WorldWideScience

Sample records for ortho metalated ruthenium

  1. Method of dissolving metal ruthenium

    Tsuno, Masao; Soda, Yasuhiko; Kuroda, Sadaomi; Koga, Tadaaki.

    1988-01-01

    Purpose: To dissolve and clean metal ruthenium deposited to the inner surface of a dissolving vessel for spent fuel rods. Method: Metal ruthenium is dissolved in a solution of an alkali metal hydroxide to which potassium permanganate is added. As the alkali metal hydroxide used herein there can be mentioned potassium hydroxide, sodium hydroxide and lithium hydroxide can be mentioned, which is used as an aqueous solution from 5 to 20 % concentration in view of the solubility of metal ruthenium and economical merit. Further, potassium permanganate is used by adding to the solution of alkali metal hydroxide at a concentration of 1 to 5 %. (Yoshihara, H.)

  2. Fabrication of ruthenium metal nanosheets via topotactic metallization of exfoliated ruthenate nanosheets.

    Fukuda, Katsutoshi; Sato, Jun; Saida, Takahiro; Sugimoto, Wataru; Ebina, Yasuo; Shibata, Tatsuo; Osada, Minoru; Sasaki, Takayoshi

    2013-03-04

    The metallization behavior of molecularly thin RuO2 nanosheets obtained from complete delamination of layered ruthenates was studied. Interestingly, the RuO2 nanosheets in a monolayer state topotactically transformed into a single layer of Ru atoms, i.e., ruthenium metal nanosheets, which can be regarded as a new family of nanosized metals.

  3. Radiochemistry of ruthenium

    Schulz, W W; Metcalf, S G; Barney, G S

    1984-06-01

    Information on ruthenium is presented. Topics include the following; isotopes and nuclear properties of ruthenium; review of the chemistry of ruthenium including metal and alloys, compounds of ruthenium, and solution chemistry; separation methods including volatilization of RuO{sub 4}, precipitation and coprecipitation, solvent extraction, chromatographic techniques, and analysis for radioruthenium. 445 refs., 7 figs., 23 tabs.

  4. Radiochemistry of ruthenium

    Schulz, W.W.; Metcalf, S.G.; Barney, G.S.

    1984-01-01

    Information on ruthenium is presented. Topics include the following; isotopes and nuclear properties of ruthenium; review of the chemistry of ruthenium including metal and alloys, compounds of ruthenium, and solution chemistry; separation methods including volatilization of RuO 4 , precipitation and coprecipitation, solvent extraction, chromatographic techniques, and analysis for radioruthenium. 445 refs., 7 figs., 23 tabs

  5. Ortho-para-conversion of hydrogen in films of rare earth metals

    Zhavoronkova, K.N.; Peshkov, A.V.

    1979-01-01

    Investigated is specific catalytic activity of REE to clarify to what an extent the change of electron structure of the metals might influence their catalytic properties. Conducted is investigation of Sc, It, La and other lanthanides, except Eu amd Pm prepared in the form of metallic films, impowdered in vacuum of 10 -7 torr. It is established, that pape earth elements as catalysts of low-temperature ortho-para-conversion od hydrogen are divided into 2 groups, differing by mechanism of the reaction. Comparison of experimental results with the calculation results of absolute rates of paramagnetic conversion and also with investigation results of isotopjc exchange on these metals showed, that on the metals of group 1 conversjon proceeds according to chemical mechanism, and on the metals of group 2 - according to oscillating magnetic mechanism

  6. Elaboration of strontium ruthenium oxide thin films on metal substrates by chemical solution deposition

    Seveno, R. [Universite de Nantes, Institut de Recherche en Electrotechnique et Electronique de Nantes Atlantique (IREENA), 2, rue de la Houssiniere, BP 92208, 44322 Nantes Cedex 3 (France)]. E-mail: raynald.seveno@univ-nantes.fr; Braud, A. [Universite de Nantes, Institut de Recherche en Electrotechnique et Electronique de Nantes Atlantique (IREENA), 2, rue de la Houssiniere, BP 92208, 44322 Nantes Cedex 3 (France); Gundel, H.W. [Universite de Nantes, Institut de Recherche en Electrotechnique et Electronique de Nantes Atlantique (IREENA), 2, rue de la Houssiniere, BP 92208, 44322 Nantes Cedex 3 (France)

    2005-12-22

    In order to improve the structural interface between a metal substrate and a lead zirconate titanate (Pb(ZrTi)O{sub 3}, PZT) ferroelectric thin film, the elaboration of strontium ruthenium oxide (SrRuO{sub 3}) by chemical solution deposition is studied. The SrRuO{sub 3} thin films were realized by multiple spin-coating technique and the temperature of the rapid thermal annealing process was optimized. The crystallization behavior was examined by X-ray diffraction; surface analyses using scanning electron microscope and atomic force microscope techniques showed the influence of the SrRuO{sub 3} layer at the interface PZT/metal on the morphology of the ferroelectric thin film. From the electrical measurements, a coercive electric field around 25 kV/cm and a remanent polarization of approximately 30 {mu}C/cm were found.

  7. Elaboration of strontium ruthenium oxide thin films on metal substrates by chemical solution deposition

    Seveno, R.; Braud, A.; Gundel, H.W.

    2005-01-01

    In order to improve the structural interface between a metal substrate and a lead zirconate titanate (Pb(ZrTi)O 3 , PZT) ferroelectric thin film, the elaboration of strontium ruthenium oxide (SrRuO 3 ) by chemical solution deposition is studied. The SrRuO 3 thin films were realized by multiple spin-coating technique and the temperature of the rapid thermal annealing process was optimized. The crystallization behavior was examined by X-ray diffraction; surface analyses using scanning electron microscope and atomic force microscope techniques showed the influence of the SrRuO 3 layer at the interface PZT/metal on the morphology of the ferroelectric thin film. From the electrical measurements, a coercive electric field around 25 kV/cm and a remanent polarization of approximately 30 μC/cm were found

  8. Synthesis, structure, electrochemistry, and photophysics of methyl-substituted phenylpyridine ortho-metalated iridium(III) complexes

    Garces, F.O.; King, K.A.; Watts, R.J.

    1988-01-01

    Synthetic, structural, photophysical, and electrochemical characterizations of ortho-metalated [Ir(NC) 2 Cl] 2 dimeric and [Ir(NC) 2 NN]Cl monomeric complexes, where NC = 2(p-tolyl)pyridine (ptpy) or 3-methyl-2-phenylpyridine (mppy) and NN = 2,2'-bipyridine (bpy) are described. Structural characterizations by 1 H and 13 C nuclear magnetic resonance (NMR) indicate the presence of symmetry elements in these complexes. The ultraviolet-visible absorption properties of these complexes are reported. The results of voltametric measurements of these complexes are included. 55 references, 10 figures, 6 tables

  9. Alkyl Chain Growth on a Transition Metal Center: How Does Iron Compare to Ruthenium and Osmium?

    Mala A. Sainna

    2015-09-01

    Full Text Available Industrial Fischer-Tropsch processes involve the synthesis of hydrocarbons usually on metal surface catalysts. On the other hand, very few homogeneous catalysts are known to perform a Fischer-Tropsch style of reaction. In recent work, we established the catalytic properties of a diruthenium-platinum carbene complex, [(CpRu2(μ2-H (μ2-NHCH3(μ3-CPtCH3(P(CH332](COn+ with n = 0, 2 and Cp = η5-C5(CH35, and showed it to react efficiently by initial hydrogen atom transfer followed by methyl transfer to form an alkyl chain on the Ru-center. In particular, the catalytic efficiency was shown to increase after the addition of two CO molecules. As such, this system could be viewed as a potential homogeneous Fischer-Tropsch catalyst. Herein, we have engineered the catalytic center of the catalyst and investigated the reactivity of trimetal carbene complexes of the same type using iron, ruthenium and osmium at the central metal scaffold. The work shows that the reactivity should increase from diosmium to diruthenium to diiron; however, a non-linear trend is observed due to multiple factors contributing to the individual barrier heights. We identified all individual components of these reaction steps in detail and established the difference in reactivity of the various complexes.

  10. Alkyl Chain Growth on a Transition Metal Center: How Does Iron Compare to Ruthenium and Osmium?

    Sainna, Mala A.; de Visser, Sam P.

    2015-01-01

    Industrial Fischer-Tropsch processes involve the synthesis of hydrocarbons usually on metal surface catalysts. On the other hand, very few homogeneous catalysts are known to perform a Fischer-Tropsch style of reaction. In recent work, we established the catalytic properties of a diruthenium-platinum carbene complex, [(CpRu)2(μ2-H)(μ2-NHCH3)(μ3-C)PtCH3(P(CH3)3)2](CO)n+ with n = 0, 2 and Cp = η5-C5(CH3)5, and showed it to react efficiently by initial hydrogen atom transfer followed by methyl transfer to form an alkyl chain on the Ru-center. In particular, the catalytic efficiency was shown to increase after the addition of two CO molecules. As such, this system could be viewed as a potential homogeneous Fischer-Tropsch catalyst. Herein, we have engineered the catalytic center of the catalyst and investigated the reactivity of trimetal carbene complexes of the same type using iron, ruthenium and osmium at the central metal scaffold. The work shows that the reactivity should increase from diosmium to diruthenium to diiron; however, a non-linear trend is observed due to multiple factors contributing to the individual barrier heights. We identified all individual components of these reaction steps in detail and established the difference in reactivity of the various complexes. PMID:26426009

  11. Synthesis of ruthenium phosphides

    Chernogorenko, V.B.; Lynchak, K.A.; Kulik, L.Ya.; Shkaravskij, Yu.F.; Klochkov, L.A.

    1977-01-01

    A method of ampoule synthesis of ruthenium phosphides, Ru 2 P, RuP, and RuP 2 , with stepwise heating of stoichimetric charges in a single-zone furnace is developed. A method for synthesizing ruthenium diphosphide by phosphidization of a ruthenium powder with phosphine at 1150 deg C is worked out. The optimum conditions of its manufacture are found by planning an extremal experiment. Interaction of PH 3 with ruthenium proceeds by the diffusion mechanism and obeys the parabolic law. An extraction-photometric method for determining phosphorus in phosphides is elaborated. Ruthenium phosphides are extremely corrosion-resistant in acids and alkalis. Ru 2 P and RuP exhibit metallic conductivity

  12. Separation of the noble metals ruthenium and palladium from nitric acid solution of the nuclear fuel reprocessing containing complexing agents

    Ghafourian, H.

    1989-06-01

    Two extraction chromatographic techniques have been developed. N'N diethylthiourea (DETU), which forms complexes with ruthenium that can be retained on an AG50W-X2 ion exchanger, has proved to be a suitable reagent. The structures of these complexes were elucidated by electrophoresis, ion exchange and IR spectroscopy. Under the same conditions Pd forms an insoluble DETU-complex of the formula [Pd(DETU) 4 ] 2+ , which allows the separation of this metal quantitatively. With regard to the application of the developed technique for recovery of the mentioned noble metals from dissolver residues of the nuclear fuel reprocessing, comparative studies were carried out for accompanying fission product nuclides and actinides such as Mo, Tc, Zr, Ce, U and Pu. It was found out that no complex between diethylthiourea and the fission products zirconium, molybdenum and cerium and the actinides uranium, plutonium and americium were formed. Technetium, which was originally present as pertechnetate, is reduced to Tc(IV) and retained on the cation exchanger together with ruthenium. Ruthenium was eluted with 6 M HNO 3 . The efficiency of the developed process has been demonstrated with simulated solutions. The achieved decontamination factors ranged from 10 2 to 10 6 depending on the nuclide. (orig./RB) [de

  13. IR-doped ruthenium oxide catalyst for oxygen evolution

    Valdez, Thomas I. (Inventor); Narayanan, Sekharipuram R. (Inventor)

    2012-01-01

    A method for preparing a metal-doped ruthenium oxide material by heating a mixture of a doping metal and a source of ruthenium under an inert atmosphere. In some embodiments, the doping metal is in the form of iridium black or lead powder, and the source of ruthenium is a powdered ruthenium oxide. An iridium-doped or lead-doped ruthenium oxide material can perform as an oxygen evolution catalyst and can be fabricated into electrodes for electrolysis cells.

  14. Electrochemical oxidation of phenol in a parallel plate reactor using ruthenium mixed metal oxide electrode

    Yavuz, Yusuf [Anadolu Universitesi, Cevre Sor. Uyg. ve Aras. Merkezi, Eskisehir (Turkey); Koparal, A. Savas [Anadolu Universitesi, Cevre Sor. Uyg. ve Aras. Merkezi, Eskisehir (Turkey)]. E-mail: askopara@anadolu.edu.tr

    2006-08-21

    In this study, electrochemical oxidation of phenol was carried out in a parallel plate reactor using ruthenium mixed metal oxide electrode. The effects of initial pH, temperature, supporting electrolyte concentration, current density, flow rate and initial phenol concentration on the removal efficiency were investigated. Model wastewater prepared with distilled water and phenol, was recirculated to the electrochemical reactor by a peristaltic pump. Sodium sulfate was used as supporting electrolyte. The Microtox'' (registered) bioassay was also used to measure the toxicity of the model wastewater during the study. As a result of the study, removal efficiency of 99.7% and 88.9% were achieved for the initial phenol concentration of 200 mg/L and chemical oxygen demand (COD) of 480 mg/L, respectively. In the same study, specific energy consumption of 1.88 kWh/g phenol removed and, mass transfer coefficient of 8.62 x 10{sup -6} m/s were reached at the current density of 15 mA/cm{sup 2}. Electrochemical oxygen demand (EOD), which can be defined as the amount of electrochemically formed oxygen used for the oxidation of organic pollutants, was 2.13 g O{sub 2}/g phenol. Electrochemical oxidation of petroleum refinery wastewater was also studied at the optimum experimental conditions obtained. Phenol removal of 94.5% and COD removal of 70.1% were reached at the current density of 20 mA/cm{sup 2} for the petroleum refinery wastewater.

  15. Theory of ortho-para conversion in hydrogen adsorbed on metal and paramagnetic surfaces at low temperatures

    Yucel, S.

    1989-01-01

    In order to explain the experimental results on Cu(100), Ag(111), Ag thin films, graphite, and H 2 bubbles in Cu, the ortho-para conversion rates of H 2 and D 2 adsorbed on metal and paramagnetic surfaces at low temperatures have been considered. The conversion rates due to magnetic dipole-dipole, Fermi contact, and spin-orbit interaction between the conduction electrons, and nuclear spins of H 2 (D 2 ) are calculated to elucidate the role of the metal surface. Although the rates on clean metal surfaces are found to be too slow to account for the observed rates on Ag, they may explain the catalytic conversion on H 2 bubble surfaces at 1.3 K. Additionally, effects of impurities and defects on the surface are investigated by calculating the conversion rate in two-dimensional solid D 2 (H 2 ) by emission of one (two) phonon(s). Fast conversion rates observed on Ag and graphite surfaces as well as on the surfaces of H 2 bubbles may be accounted for by paramagnetic impurities or defects. On Grafoil, both in (√3 x √3)R30 0 commensurate and incommensurate solid phase, a temperature-independent conversion rate is predicted if the mobility of the molecules is high enough to prevent concentration gradients

  16. Element specificity of ortho-positronium annihilation for alkali-metal loaded SiO2 glasses.

    Sato, K; Hatta, T

    2015-03-07

    Momentum distributions associated with ortho-positronium (o-Ps) pick-off annihilation photon are often influenced by light elements, as, e.g., carbon, oxygen, and fluorine. This phenomenon, so-called element specificity of o-Ps pick-off annihilation, has been utilized for studying the elemental environment around the open spaces. To gain an insight into the element specificity of o-Ps pick-off annihilation, the chemical shift of oxygen 1s binding energy and the momentum distributions associated with o-Ps pick-off annihilation were systematically investigated for alkali-metal loaded SiO2 glasses by means of X-ray photoelectron spectroscopy and positron-age-momentum correlation spectroscopy, respectively. Alkali metals introduced into the open spaces surrounded by oxygen atoms cause charge transfer from alkali metals to oxygen atoms, leading to the lower chemical shift for the oxygen 1s binding energy. The momentum distribution of o-Ps localized into the open spaces is found to be closely correlated with the oxygen 1s chemical shift. This correlation with the deepest 1s energy level evidences that the element specificity of o-Ps originates from pick-off annihilation with orbital electrons, i.e., dominantly with oxygen 2p valence electrons and s electrons with lower probability.

  17. Inductively Coupled Plasma Mass Spectrometry: Sample Analysis of Zirconium and Ruthenium in Metal Organic Frameworks

    2018-02-01

    linear regression fits for the calibration curves. The goodness of the linear fits are summarized in Table 3 and Figure 1. Table 3. Concentration...and ruthenium at each calibration level. 11 REFERENCES 1. General Requirements for the Competence of Testing and Calibration Laboratories

  18. Electrochemical transformations of oxygen and the defect structure of solid solutions on the basis of alkaline earth metal ortho-vanadates

    Khodos, M.Ya.; Belysheva, G.M.; Brajnina, Kh.Z.

    1986-01-01

    Effect of iso- and heterovalent substitution in the structure of alkaline earth metal ortho-vanadates and synthesis conditions, simulating the definite type of their crystal lattice disordering, on the character of potentiodynamic anodic-cathodic curves has been investigated by the method of cyclic voltammetry. Correlation between signals observed and the defect structure of oxide compounds is refined. Oxygen chemisorption is shown to be determined by concentration of nonequilibrium oxygen vacancies, which formation is accompanied by appearance of quasi-free electrons

  19. Studies of dissolution solutions of ruthenium metal, oxide and mixed compounds in nitric acid

    Mousset, F.; Eysseric, C.; Bedioui, F.

    2004-01-01

    Ruthenium is one of the fission products generated by irradiated nuclear fuel. It is present throughout all the steps of nuclear fuel reprocessing-particularly during extraction-and requires special attention due to its complex chemistry and high βγ activity. An innovative electro-volatilization process is now being developed to take advantage of the volatility of RuO 4 in order to eliminate it at the head end of the Purex process and thus reduce the number of extraction cycles. Although the process operates successfully with synthetic nitrato-RuNO 3+ solutions, difficulties have been encountered in extrapolating it to real-like dissolution solutions. In order to better approximate the chemical forms of ruthenium found in fuel dissolution solutions, kinetic and speciation studies on dissolved species were undertaken with RuO 2 ,xH 2 O and Ru 0 in nitric acid media. (authors)

  20. Conversion of cellulose and cellobiose into sorbitol catalyzed by ruthenium supported on a polyoxometalate/metal-organic framework hybrid.

    Chen, Jinzhu; Wang, Shengpei; Huang, Jing; Chen, Limin; Ma, Longlong; Huang, Xing

    2013-08-01

    Cellulose and cellobiose were selectively converted into sorbitol over water-tolerant phosphotungstic acid (PTA)/metal- organic-framework-hybrid-supported ruthenium catalysts, Ru-PTA/MIL-100(Cr), under aqueous hydrogenation conditions. The goal was to investigate the relationship between the acid/metal balance of bifunctional catalysts Ru-PTA/MIL-100(Cr) and their performance in the catalytic conversion of cellulose and cellobiose into sugar alcohols. The control of the amount and strength of acid sites in the supported PTA/MIL-100(Cr) was achieved through the effective control of encapsulated-PTA loading in MIL-100(Cr). This design and preparation method led to an appropriately balanced Ru-PTA/MIL-100(Cr) in terms of Ru dispersion and hydrogenation capacity on the one hand, and acid site density of PTA/MIL-100(Cr) (responsible for acid-catalyzed hydrolysis) on the other hand. The ratio of acid site density to the number of Ru surface atoms (nA /nRu ) of Ru-PTA/MIL-100(Cr) was used to monitor the balance between hydrogenation and hydrolysis functions; the optimum balance between the two catalytic functions, that is, 8.84sorbitol of 57.9% at complete conversion of cellulose, and 97.1% yield in hexitols with a selectivity for sorbitol of 95.1% at complete conversion of cellobiose) were obtained using a Ru-PTA/MIL-100(Cr) catalyst with loadings of 3.2 wt % for Ru and 16.7 wt % for PTA. This research thus opens new perspectives for the rational design of acid/metal bifunctional catalysts for biomass conversion. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Formation of aqueous complexes of metal ions formed during the reprocessing of nuclear fuels with ortho-phenanthroline and dibutylphosphate

    Musikas, C.; Le Marois, G.; Racinoux, J.

    1979-01-01

    In this work the formation of aqueous complexes of metalions (lanthanides, actinides) was investigated that occurs during reprocessing of nuclear combustibles with ortho-phenanthroline and dibutylphosphate. Complexes with different ligand numbers and solubility are formed. Cationic and anionic forms according to the DBP concentration in the extraction solution. Acid-base titrations, absorption spectra and solubility determinations were used for the characterization. (RB) [de

  2. Titrimetric determination of ruthenium

    Velichko, V.V.; Belyaeva, T.I.; Kudinova, V.K.; Usatenko, Yu.I.

    1978-01-01

    Titration of ruthenium(4) hydrochloric-acid solutions with Mohr's salt, hydroquinone, and thiourea has been studied with the use of biampero- and potentiometric indication of the titration end point (t.e.p.) Potentiometric and amperometric indication of the t.e.p. is applicable when Ru(4) concentration is from 20 to 6000 mkg in 20 ml of the titrated solution; biamperometric indication can be used at a concentration of 5-1000 mkg in the same volume. It has been established that titration of Ru(4) (in the form of the Na 2 RuCl 6 solution) with Mohr's salt is not hindered by the presence of 1000-fold excess of alkaline and alkali-earth metals, Al, Ti(4), Mn(2), Cr(3), Fe(3), Co, Ni, Cu, Zn, Ga, Ge(4), As, Se, Mo(6), Cd, In, and Te; 100-fold excess of Rh, Pd, W, Bi, and Sn; 10-fold excess of Ag, Au, Pt, Hg, Os. Along with Ru(4) titrated are Ir(4), Te(3), V(5), and Ce(4). Selectivity of hydroquinone and thiourea is lower. Titrimetric procedure of determining ruthenium has been tested for ruthenium alloy containing cobalt tungsten. It cannot be recommended for analysis of the samples which dissolve in aqua regia

  3. Interface engineering and reliability characteristics of hafnium dioxide with poly silicon gate and dual metal (ruthenium-tantalum alloy, ruthenium) gate electrode for beyond 65 nm technology

    Kim, Young-Hee

    Chip density and performance improvements have been driven by aggressive scaling of semiconductor devices. In both logic and memory applications, SiO 2 gate dielectrics has reached its physical limit, direct tunneling resulting from scaling down of dielectrics thickness. Therefore high-k dielectrics have attracted a great deal of attention from industries as the replacement of conventional SiO2 gate dielectrics. So far, lots of candidate materials have been evaluated and Hf-based high-k dielectrics were chosen to the promising materials for gate dielectrics. However, lots of issues were identified and more thorough researches were carried out on Hf-based high-k dielectrics. For instances, mobility degradation, charge trapping, crystallization, Fermi level pinning, interface engineering, and reliability studies. In this research, reliability study of HfO2 were explored with poly gate and dual metal (Ru-Ta alloy, Ru) gate electrode as well as interface engineering. Hard breakdown and soft breakdown were compared and Weibull slope of soft breakdown was smaller than that of hard breakdown, which led to a potential high-k scaling issue. Dynamic reliability has been studied and the combination of trapping and detrapping contributed the enhancement of lifetime projection. Polarity dependence was shown that substrate injection might reduce lifetime projection as well as it increased soft breakdown behavior. Interface tunneling mechanism was suggested with dual metal gate technology. Soft breakdown (l st breakdown) was mainly due to one layer breakdown of bi-layer structure. Low weibull slope was in part attributed to low barrier height of HfO 2 compared to interface layer. Interface layer engineering was thoroughly studied in terms of mobility, swing, and short channel effect using deep sub-micron MOSFET devices. In fact, Hf-based high-k dielectrics could be scaled down to below EOT of ˜10A and it successfully achieved the competitive performance goals. However, it is

  4. Bioinspired organocatalytic aerobic C-H oxidation of amines with an ortho-quinone catalyst.

    Qin, Yan; Zhang, Long; Lv, Jian; Luo, Sanzhong; Cheng, Jin-Pei

    2015-03-20

    A simple bioinspired ortho-quinone catalyst for the aerobic oxidative dehydrogenation of amines to imines is reported. Without any metal cocatalysts, the identified optimal ortho-quinone catalyst enables the oxidations of α-branched primary amines and cyclic secondary amines. Mechanistic studies have disclosed the origins of different performances of ortho-quinone vs para-quinone in biomimetic amine oxidations.

  5. Photoisomerization Mechanism of Ruthenium Sulfoxide Complexes: Role of the Metal-Centered Excited State in the Bond Rupture and Bond Construction Processes.

    Li, Huifang; Zhang, Lisheng; Zheng, Lvyin; Li, Xun; Fan, Xiaolin; Zhao, Yi

    2016-09-26

    Phototriggered intramolecular isomerization in a series of ruthenium sulfoxide complexes, [Ru(L)(tpy)(DMSO)](n+) (where tpy=2,2':6',2''-terpyridine; DMSO=dimethyl sulfoxide; L=2,2'-bipyridine (bpy), n=2; N,N,N',N'-tetramethylethylenediamine (tmen) n=2; picolinate (pic), n=1; acetylacetonate (acac), n=1; oxalate (ox), n=0; malonate (mal), n=0), was investigated theoretically. It is observed that the metal-centered ligand field ((3) MC) state plays an important role in the excited state S→O isomerization of the coordinated DMSO ligand. If the population of (3) MCS state is thermally accessible and no (3) MCO can be populated from this state, photoisomerization will be turned off because the (3) MCS excited state is expected to lead to fast radiationless decay back to the original (1) GSS ground state or photodecomposition along the Ru(2+) -S stretching coordinate. On the contrary, if the population of (3) MCS (or (3) MCO ) state is inaccessible, photoinduced S→O isomerization can proceed adiabatically on the potential energy surface of the metal-to-ligand charge transfer excited states ((3) MLCTS →(3) MLCTO ). It is hoped that these results can provide valuable information for the excited state isomerization in photochromic d(6) transition-metal complexes, which is both experimentally and intellectually challenging as a field of study. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Fundamental Factors Impacting the Stability of Phosphonate-Derivatized Ruthenium Polypyridyl Sensitizers Adsorbed on Metal Oxide Surfaces.

    Raber, McKenzie; Brady, Matthew David; Troian-Gautier, Ludovic; Dickenson, John; Marquard, Seth L; Hyde, Jacob; Lopez, Santiago; Meyer, Gerald J; Meyer, Thomas J; Harrison, Daniel P

    2018-06-08

    A series of 18 ruthenium(II) polypyridyl complexes were synthesized and evaluated under electrochemically oxidative conditions, which generates the Ru(III) oxidation state and mimics the harsh conditions experienced during the kinetically-limited regime that can occur in dye-sensitized solar cells (DSSCs) and dye-sensitized photoelectrosynthesis cells (DSPECs), to further develop fundamental insights into the factors governing molecular sensitizer surface stability in aqueous 0.1 M HClO4 (aq). Both desorption and oxidatively induced ligand substitution were observed on planar fluorine doped tin oxide, FTO, electrodes, with a dependence on the E1/2 Ru(III/II) redox potential dictating the comparative ratios of the processes. Complexes such as RuP4OMe (E1/2 = 0.91 vs Ag/AgCl) displayed virtually only desorption, while complexes such as RuPbpz (E1/2 > 1.62 V vs Ag/AgCl) displayed only chemical decomposition. Comparing isomers of 4,4'- and 5,5-disubstituted-2,2'-bipyridine ancillary polypyridyl ligands, a dramatic increase in the rate of desorption of the Ru(III) complexes was observed for the 5,5'-ligands. Nanoscopic indium doped tin oxide thin films, nanoITO, were also sensitized and analyzed with cyclic voltammetry, UV-Vis absorption spectroscopy, and XPS, allowing for further distinction of desorption versus ligand substitution processes. Desorption loss to bulk solution associated with the planar surface of FTO is essentially non-existent on nanoITO, where both desorption and ligand substitution are shut down with RuP4OMe. These results revealed that minimizing time spent in the oxidized form, incorporating electron donating groups, maximizing hydrophobicity, and minimizing molecular bulk near the adsorbed ligand are critical to optimizing the performance of ruthenium(II) polypyridyl complexes in dye-sensitized solar cell devices.

  7. Electrochemical studies of ruthenium compounds

    Kumar Ghosh, B.; Chakravorty, A.

    1989-01-01

    In many ways the chemistry of transition metals is the chemistry of multiple oxidation states and the associated redox phenomena. If a particular element were to be singeld out to illustrate this viewpoint, a model choice would be ruthenium - an element that is directly or indirectly the active centre of a plethora of redox phenomena encompassing ten different oxidation states and a breathtaking diversity of structure and bonding. In the present review the authors are primarily concerned with the oxidation states of certain ligands coordinated to ruthenium. This choice is deliberate since this is one area where the unique power of electrochemical methods is splendidly revealed. Without these methods, development in this area would have been greatly hampered. A brief summary of metal oxidation states is also included as a prelude to the main subject of this review. The authors have generally emphasize the information derived which is of chemical interest leaving the details of formal electrochemical arguments in the background. The authors have reviewed the pattern and systematics of ligand redox in ruthenium complexes. The synergistic combination of electrochemical and spectroscopic methods have vastly increased our understanding of ligand phenomena during the last 15 years or so. This in turn has led to better understanding and new developments in other fields. Photophysics and photochemistry could be cited as examples. (author). 176 refs.; 10 figs.; 10 tabs

  8. Unsaturated carbone and allenylidene ruthenium complexes from alkynes

    Bozek, Yu.L.; Diznev, P.A.

    1995-01-01

    The author's studies aimed at activation of terminal alkynes by metal complexes, reactivity patterns and selective preparations of unsaturated carbene, allenylidene and cumulenylidene derivatives of (arene)ruthenium complexes are reviewed. 48 refs

  9. Polarographic determination of ruthenium

    Li Jifu; Duan Shirong; Wu Xi

    1989-01-01

    It is suggested to use 0.5 mol/l HClO 4 -0.5 mol/l NaNO 3 -0.1 mol/l NaClO 4 as supporting electrolyte for determining ruthenium. In the supporting electrolyte there is a clear polarographic wave of ruthenium (IV) at -0.8 V vs. SCE. The wave height of ruthenium(IV) is linear in the range from 0.1 to 0.4 μg. ml -1 . The effect of the component of supporting electroylte and the other ion in the samples on the measurement of ruthenium are studied. The analysis methods for measuring ruthenium in both acidic or basic imitative radioactive waste solutions which is used in study of glass solidification are worked out. Imitative samples are analysised

  10. Atomic Layer Deposition of Ruthenium with TiN Interface for Sub-10 nm Advanced Interconnects beyond Copper

    Wen, Liang Gong; Roussel, Philippe; Pedreira, Olalla Varela

    2016-01-01

    . These extremely scaled ruthenium lines show excellent electromigration behavior. Time-dependent dielectric breakdown measurements reveal negligible ruthenium ion drift into low-kappa dielectrics up to 200 degrees C, demonstrating that ruthenium can be used as a barrierless metallization in interconnects...

  11. Synthesis of PVP-stabilized ruthenium colloids with low boiling point alcohols.

    Zhang, Yuqing; Yu, Jiulong; Niu, Haijun; Liu, Hanfan

    2007-09-15

    A route to the preparation of poly(N-vinyl-2-pyrrolidone) (PVP)-stabilized ruthenium colloids by refluxing ruthenium(III) chloride in low boiling point alcohols was developed. Deep purple colloids with shuttle-like ruthenium particles were also synthesized. XPS measurement verified the nanoparticles were in the metallic state. The morphology of metal nanoparticles was characterized by UV-visible absorption spectrophotometry, TEM and XRD.

  12. Metal-ligand cooperative activation of nitriles by a ruthenium complex with a de-aromatized PNN pincer ligand

    Eijsink, Linda E; Perdriau, Sébastien C P; de Vries, Johannes G; Otten, Edwin

    2016-01-01

    The pincer complex (PNN)RuH(CO), with a de-aromatized pyridine in the ligand backbone, is shown to react with nitriles in a metal-ligand cooperative manner. This leads to the formation of a series of complexes with new Ru-N(nitrile) and C(ligand)-C(nitrile) bonds. The initial nitrile cycloaddition

  13. Ruthenium removing device

    Kitamura, Masafumi; Shirado, Katsuyuki.

    1990-01-01

    A processing gas supply system and a NO x supply system for supplying NO x to be mixed with processed gases are connected to the gas plenum in the lower portion of reaction vessel. Further, a cleaning station is disposed above the gas plenum for introducing a mixed gas stream from the gas plenum into a liquid detergent thereby trapping NO x and ruthenium reduction products into the liquid detergent. Volatile ruthenium contained in the processed gases is reduced into ruthenium reduction products and formed as mists. They are trapped in the cleaning liquid and the remaining gases are discharged out of the liquid detergent to the outside of the reaction vessel. Accordingly, solid radioactive wastes are not formed and the decontaminating efficiency for volatile ruthenium can be improved. (T.M.)

  14. Solvothermal growth of a ruthenium metal-organic framework featuring HKUST-1 structure type as thin films on oxide surfaces.

    Kozachuk, Olesia; Yusenko, Kirill; Noei, Heshmat; Wang, Yuemin; Walleck, Stephan; Glaser, Thorsten; Fischer, Roland A

    2011-08-14

    Phase-pure crystalline thin films of a mixed-valence Ru(2)(II,III) metal-organic framework with 1,3,5-benzenetricarboxylate (btc) as a linker were solvothermally grown on amorphous alumina and silica surfaces. Based on the Rietveld refinement, the structure of Ru-MOF was assigned to be analogous to [Cu(3)(btc)(2)] (HKUST-1). This journal is © The Royal Society of Chemistry 2011

  15. Increased electrochemical properties of ruthenium oxide and graphene/ruthenium oxide hybrid dispersed by polyvinylpyrrolidone

    Chen, Yao; Zhang, Xiong; Zhang, Dacheng; Ma, Yanwei

    2012-01-01

    Highlights: ► A good dispersion of RuO 2 and graphene/RuO 2 is obtained by polyvinylpyrrolidone. ► PVP as a dispersant also can prevent the formation of metal Ru in graphene/RuO 2 . ► The max capacitances of the hybrid and RuO 2 reach 435 and 597 F g −1 at 0.2 A g −1 . ► The hybrid shows the best rate capability of 39% at 50 A g −1 . - Abstract: Ruthenium oxide has been prepared by a sol–gel method. Polyvinylpyrrolidone (PVP) as an excellent polymeric dispersant is adopted to prevent aggregation of ruthenium oxide. In order to enhance the rate capability of ruthenium oxide, graphene with residual oxygen functional groups as a 2D support has been merged into ruthenium oxide. These oxygen functional groups not only favor to form stable few layers of graphene colloids, but also offer the sites to anchor ruthenium oxide nanoparticles. X-ray diffraction infers that PVP can also hinder the partial formation of Ru by blocking the direct contact between the Ru 3+ and the graphene in the sol–gel synthesis of the hybrids. The ruthenium oxide and the graphene/ruthenium oxide hybrids dispersed by PVP have superior electrochemical properties due to good dispersing and protecting ability of PVP. Especially, the hybrids using PVP exhibit the best rate capability, indicating that the composites possess an advanced structure of combining sheets and particles in nano-scale.

  16. Confinement of ruthenium oxides volatilized during nuclear fuels reprocessing

    Maas, E.T. Jr.; Longo, J.M.

    1980-01-01

    While many materials have been suggested and employed as trapping agents for gaseous oxides of fission product ruthenium volatilized during nuclear fuels reprocessing, none that is known to form thermodynamically stable compounds with rutheniunm has been utilized. We have employed alkaline earth metal compounds for this purpose because of their ability to form stable mixed metal oxide phases with ruthenium. Results of experiments in which RuO 4 was volatilized from either a solid source (RuO 2 .xH 2 O) or from solution [Ru(NO)(NO 3 ) 3 ] in HNO 3 and passed through beds of alkaline earth metal carbonates and calcium oxide held at 600 to 750 0 C have demonstrated that compounds of formulation MRuO 3 (M = calcium, strontium, barium) are formed. Under oxidizing conditions, these materials exist as stable ceramic phases, whereas under reducing conditions, they are transformed into intimate mixtures of the alkaline earth metal oxide and nonvolatile ruthenium metal

  17. Analysis of radioactive ruthenium

    1977-01-01

    This manual explains the procedures of analysis of radioactive ruthenium in the drain water from atomic energy plants. The most important radioactive ruthenium is 106 Ru, and the method of measurement described in this manual is to measure the beta ray of the daughter nuclide 106 Rh. The samples to be measured are collected from seawater, marine living things, and sediment of sea bottom near atomic energy plants. In case of sea water, the ruthenium is separated by the co-precipitation with magnesium hydroxide and distillation or the extraction with carbon tetrachloride, reduction and precipitation. The beta ray of the obtained sample is measured by a gas-flow type low background β counting system. Alkali dissolution-distillation or nitric acid extraction-distillation, reduction and precipitation are applied for marine living things. The sediment of sea bottom is treated with nitric acid or strong phosphoric acid, and distilled then the ruthenium is reduced and precipitated, and the beta-counting of the precipitation is made. The method to fix radioactive ruthenium on polyethylene films after the co-precipitation is also described for reference. The detectable levels by the present methods are 0.05 pCi/l for sea water, 0.1 pCi/g for marine living things, and 20 pCi/kg for the sediment of sea bottom. (Kato, T.)

  18. Ruthenium(ii)-polypyridyl zirconium(iv) metal-organic frameworks as a new class of sensitized solar cells.

    Maza, W A; Haring, A J; Ahrenholtz, S R; Epley, C C; Lin, S Y; Morris, A J

    2016-01-01

    A series of Ru(ii)L 2 L' (L = 2,2'-bipyridyl, L' = 2,2'-bipyridine-5,5'-dicarboxylic acid), RuDCBPY, -containing zirconium(iv) coordination polymer thin films have been prepared as sensitizing materials for solar cell applications. These metal-organic framework (MOF) sensitized solar cells, MOFSCs, each are shown to generate photocurrent in response to simulated 1 sun illumination. Emission lifetime measurements indicate the excited state quenching of RuDCBPY at the MOF-TiO 2 interface is extremely efficient (>90%), presumably due to electron injection into TiO 2 . A mechanism is proposed in which RuDCBPY-centers photo-excited within the MOF-bulk undergo isotropic energy migration up to 25 nm from the point of origin. This work represents the first example in which a MOFSC is directly compared to the constituent dye adsorbed on TiO 2 (DSC). Importantly, the MOFSCs outperformed their RuDCBPY-TiO 2 DSC counterpart under the conditions used here and, thus, are solidified as promising solar cell platforms.

  19. Transition Metal Catalyzed Hydroarylation of Multiple Bonds: Exploration of Second Generation Ruthenium Catalysts and Extension to Copper Systems

    T. Brent Gunnoe

    2011-02-17

    Catalysts provide foundational technology for the development of new materials and can enhance the efficiency of routes to known materials. New catalyst technologies offer the possibility of reducing energy and raw material consumption as well as enabling chemical processes with a lower environmental impact. The rising demand and expense of fossil resources has strained national and global economies and has increased the importance of accessing more efficient catalytic processes for the conversion of hydrocarbons to useful products. The goals of the research are to develop and understand single-site homogeneous catalysts for the conversion of readily available hydrocarbons into useful materials. A detailed understanding of these catalytic reactions could lead to the development of catalysts with improved activity, longevity and selectivity. Such transformations could reduce the environmental impact of hydrocarbon functionalization, conserve energy and valuable fossil resources and provide new technologies for the production of liquid fuels. This project is a collaborative effort that incorporates both experimental and computational studies to understand the details of transition metal catalyzed C-H activation and C-C bond forming reactions with olefins. Accomplishments of the current funding period include: (1) We have completed and published studies of C-H activation and catalytic olefin hydroarylation by TpRu{l_brace}P(pyr){sub 3}{r_brace}(NCMe)R (pyr = N-pyrrolyl) complexes. While these systems efficiently initiate stoichiometric benzene C-H activation, catalytic olefin hydroarylation is hindered by inhibition of olefin coordination, which is a result of the steric bulk of the P(pyr){sub 3} ligand. (2) We have extended our studies of catalytic olefin hydroarylation by TpRu(L)(NCMe)Ph systems to L = P(OCH{sub 2}){sub 3}CEt. Thus, we have now completed detailed mechanistic studies of four systems with L = CO, PMe{sub 3}, P(pyr){sub 3} and P(OCH{sub 2}){sub 3}CEt

  20. A new approach to synthesize supported ruthenium phosphides for hydrodesulfurization

    Wang, Qingfang; Wang, Zhiqiang; Yin, Xiaoqian; Zhou, Linxi; Zhang, Minghui

    2016-01-01

    Highlights: • We bring out a new method to synthesize noble metal phosphides at low temperature. • Both RuP and Ru_2P were synthesized using triphenylphosphine as phosphorus sources. • Ru_2P was the better active phase for HDS than RuP and metal Ru. • RuP/SiO_2 prepared by new method had better HDS activity to that by TPR method. - Abstract: Supported noble metal ruthenium phosphides were synthesized by one-step H_2-thermal treatment method using triphenylphosphine (TPP) as phosphorus sources at low temperatures. Two phosphides RuP and Ru_2P can be prepared by this method via varying the molar ratio of metal salt and TPP. The as-prepared phosphides were characterized by X-ray powder diffraction (XRD), low-temperature N_2 adsorption, CO chemisorption and transmission electronic microscopy (TEM). The supported ruthenium phosphides prepared by new method and conventional method together with contradistinctive metallic ruthenium were evaluated in hydrodesulfurization (HDS) of dibenzothiophene (DBT). The catalytic results showed that metal-rich Ru_2P was the better active phase for HDS than RuP and metal Ru. Besides this, ruthenium phosphide catalyst prepared by new method exhibited superior HDS activity to that prepared by conventional method.

  1. A new approach to synthesize supported ruthenium phosphides for hydrodesulfurization

    Wang, Qingfang [Tianjin Key Laboratory of Water Environment and Resources, Tianjin Normal University, Tianjin 300387 (China); Key Laboratory of Advanced Energy Materials Chemistry (MOE), Collaborative Innovation Center of Chemical Science and Engineering (Tianjin), College of Chemistry, Nankai University, Tianjin 300071 (China); Wang, Zhiqiang [Tianjin Key Laboratory of Water Environment and Resources, Tianjin Normal University, Tianjin 300387 (China); Yin, Xiaoqian; Zhou, Linxi [Key Laboratory of Advanced Energy Materials Chemistry (MOE), Collaborative Innovation Center of Chemical Science and Engineering (Tianjin), College of Chemistry, Nankai University, Tianjin 300071 (China); Zhang, Minghui, E-mail: zhangmh@nankai.edu.cn [Key Laboratory of Advanced Energy Materials Chemistry (MOE), Collaborative Innovation Center of Chemical Science and Engineering (Tianjin), College of Chemistry, Nankai University, Tianjin 300071 (China); College of Chemistry and Environmental Science, Kashgar University, Kashgar 844006 (China)

    2016-02-15

    Highlights: • We bring out a new method to synthesize noble metal phosphides at low temperature. • Both RuP and Ru{sub 2}P were synthesized using triphenylphosphine as phosphorus sources. • Ru{sub 2}P was the better active phase for HDS than RuP and metal Ru. • RuP/SiO{sub 2} prepared by new method had better HDS activity to that by TPR method. - Abstract: Supported noble metal ruthenium phosphides were synthesized by one-step H{sub 2}-thermal treatment method using triphenylphosphine (TPP) as phosphorus sources at low temperatures. Two phosphides RuP and Ru{sub 2}P can be prepared by this method via varying the molar ratio of metal salt and TPP. The as-prepared phosphides were characterized by X-ray powder diffraction (XRD), low-temperature N{sub 2} adsorption, CO chemisorption and transmission electronic microscopy (TEM). The supported ruthenium phosphides prepared by new method and conventional method together with contradistinctive metallic ruthenium were evaluated in hydrodesulfurization (HDS) of dibenzothiophene (DBT). The catalytic results showed that metal-rich Ru{sub 2}P was the better active phase for HDS than RuP and metal Ru. Besides this, ruthenium phosphide catalyst prepared by new method exhibited superior HDS activity to that prepared by conventional method.

  2. THE MICROSOFT GLOBAL ORTHO PROGRAM

    W. Walcher

    2012-07-01

    Full Text Available Wide area and thus continental mapping extending beyond national borders is a novel concept in civilian photogrammetry. The Microsoft Global Ortho Program was launched in the Spring of 2009 as a result of Microsoft's need for global geo-data at a high geometric resolution and radiometric excellence. By fall of 2012 more than 10 million km2 of the USA and 14 European countries will have been covered by seamless 30 cm GSD color-, 60 cm GSD false-color infrared ortho-mosaics and a 1 meter GSD digital surface model. The ortho-maps are being published to Microsoft's Bing Maps Internet mapping portal. The Global Ortho Program was designed for highly and unprecedented automated mapping of essentially entire continents. In 2011, exclusive of flight operations, the product output per person has been measured in excess of 275,000 square km per year. We describe research efforts that made this achievement possible. Those include a specially designed aerial sensor (Ultracam G, logistics simulation for fight planning and optimization, in-flight blur detection and subsequent automatic blur removal, modeling and removal of atmospheric and environmental conditions, automated shear detection and DTM refinement, an IT architecture to process >200,000 aerial images/day, and for creating over 1,000,000 km2 ortho-imagery and DSM data in 24 hours. While addressing these issues, we provide ideas how this might affect the future of spatial infrastructure initiatives.

  3. Process for separating the ortho- and para- isomers of hydroxymandelic acid or a salt thereof, the isomers thus obtained, the use of the ortho-isomer for the preparation of eddha

    Hoefnagel, A.J.; Van Bekkum, H.

    1994-01-01

    Abstract of WO 9414746 (A1) The invention relates to a method for separating the ortho- and para-isomers of hydroxymandelic acid or a salt thereof. For that purpose the starting material is a solid mixture of these ortho- and para-isomers in the alkali metal salt form. This mixture is extracted with

  4. Ruthenium separation device from radioactive waste

    Ayabe, Osao.

    1988-01-01

    Purpose: To efficiently oxidize ruthenium in radioactive wastes and evaporize ruthenium tetraoxide after oxidization thereof, thereby improve the separation and recovery rate. Constitution: The device comprises an oxidization vessel for supplying an oxidizing agent into radioactive wastes to oxidize ruthenium in the wastes into ruthenium tetraoxide, and a distillation vessel for introducing radioactive wastes after oxidization, distillating under heating ruthenium tetraoxide leached into the wastes and evaporizing ruthenium tetraoxide. By dividing the device into the oxidizing vessel and the distillation vessel, the oxidizing treatment and the distilling treatment can individually be operated optimally to improve the separation and recovery rate of ruthenium. (Takahashi, M.)

  5. Determination of biogenic amines from electrocatalytic responses of graphite electrodes modified with metallic osmium or an osmium oxide-ruthenium cyanide film

    Shajdarova, L.G.; Gedmina, A.V.; Chelnokova, I.A.; Budnikov, G.K.

    2008-01-01

    Particles of osmium or an inorganic polymeric film of osmium oxide-ruthenium cyanide (OsO-RuCN) electrodeposited on glassy carbon (GC) electrocatalyze the oxidation of dopamine (DA), adrenaline (AD), and noradrenaline (NAD). It is found that these biogenic amines are determined with a high sensitivity by oxidation at an electrode with an OsO-RuCN film. Procedures for the voltammetric determination of DA, AD, or NAD at a composite film electrode are developed. The currents of the substrate oxidation are linear functions of the concentrations in the ranges from 5x10 -7 to 1x10 -3 M for DA and from 1x10 -6 to 1x10 -3 M for AD and NAD [ru

  6. Electroerosion method for preparation of saturated solutions of ruthenium hydroxochloride

    Mikhalev, V.A.; Andrianov, G.A.; Zhadanov, B.V.; Ryazanov, A.I.

    1987-01-01

    A pilot plant for carrying out electroerosion processes using pulse current of high unit power is developed. The solution process of metallic Ru in concentrated HCl is investigated. The possibility of preparation of ruthenium hydroxochloride solutions of 300 g/l concentration is established; it gives the possibility of Ru solution under conditions similar to the process of salting out

  7. Electrochemical behavior of ruthenium (III), rhodium (III) and palladium (II) in 1-butyl-3-methylimidazolium chloride ionic liquid

    Jayakumar, M.; Venkatesan, K.A. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Srinivasan, T.G. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India)], E-mail: tgs@igcar.gov.in; Vasudeva Rao, P.R. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India)

    2009-11-01

    Electrochemical behavior of ruthenium (III), rhodium (III) and palladium (II) in 1-butyl-3-methylimidazolium chloride (bmimCl) and their ternary and binary solutions in bmimCl was studied at various working electrodes at 373 K by cyclic voltammetry and chronoamperometry. Ruthenium (III) chloride forms a stable solution with bmimCl and the cyclic voltammogram of ruthenium (III) in bmimCl recorded at glassy carbon electrode consisted of several redox waves due to the complex nature of ruthenium to exist in several oxidation states. Electrolysis of ruthenium (III) chloride in bmimCl at the cathodic limit of bmimCl (-1.8 V (vs. Pd)) did not result in ruthenium metal deposition. However, it was deposited from bmimPF{sub 6} and bmimNTf{sub 2} room temperature ionic liquids at -0.8 V (vs. Pd). The electrochemical behavior of ruthenium (III) in bmimCl in the presence of palladium (II) and rhodium (III) was studied by cyclic voltammetry. The presence of palladium (II) in bmimCl favors underpotential deposition of ruthenium metal. The nuclear loop at -0.5 V (vs. Pd) was observed in all solutions when palladium (II) co-existed with other two metal ions. Nucleation and growth of the metal on glassy carbon working electrode was investigated by chronoamperometry. The growth and decay of chronocurrents has been found to follow the instantaneous nucleation model with three-dimensional growth of nuclei.

  8. The use of ruthenium in various fields of industry

    Sinitsin, N.M.

    1990-03-01

    Metallic ruthenium, its alloys, and compounds with other metals have a number of valuable and specific properties which allow the usage of ruthenium in various fields of modern technology, which is described here. In the atomic technology, Ru can be used in the building of reactors as a material of construction since its isotopes don't possess a high neutron capture cross section. Ruthenium is used for the preparation of γ- and β-ray emission sources. Isotopes Ru-103 and Ru-106 are widely used as tracers. They are successfully used for the monitoring of production, for the development of new technological and analytical methods of the extraction of Ru, for the cleansing of other valuable metals from Ru, for the monitoring of the thickness of Ru microfilm on the substrate, and for the monitoring of Ru losses in various processes. In the nuclear reactor, during the process of uranium and plutonium decay, large amounts of stable Ru isotopes are formed together with radioactive isotopes. In such a manner, a nuclear reactor can supply Ru. Special attention must be paid to the usage of direct coordination Ru compounds. Ru and its compounds possess a large number of very valuable properties, many of the secrets of Ru must still be discovered. It can be presumed that the demand for ruthenium will grow in the forthcoming years and the range and volume of its applications will increase

  9. Ruthenium nanocatalysis on redox reactions.

    Veerakumar, Pitchaimani; Ramdass, Arumugam; Rajagopal, Seenivasan

    2013-07-01

    Nanoparticles have generated intense interest over the past 20 years due to their high potential applications in different areas such as catalysis, sensors, nanoscale electronics, fuel and solar cells and optoelectronics. As the large fractions of metal atoms are exposed to the surface, the use of metal nanoparticles as nanocatalysts allows mild reaction conditions and high catalytic efficiency in a large number of chemical transformations. They have emerged as sustainable heterogeneous catalysts and catalyst supports alternative to conventional materials. This review focuses on the synthesis, characterization and catalytic role of ruthenium nanoparticles (RuNPs) on the redox reactions of heteroatom containing organic compounds with the green reagent H2O2, a field that has attracted immense interest among the chemical, materials and industrial communities. We intend to present a broad overview of Ru nanocatalysts for redox reactions with an emphasis on their performance, stability and reusability. The growth in the chemistry of organic sulfoxides and N-oxides during last decade was due to their importance as synthetic intermediates for the production of a wide range of chemically and biologically active molecules. Thus design of efficient methods for the synthesis of sulfoxides and N-oxides becomes important. This review concentrates on the catalysis of RuNPs on the H2O2 oxidation of organic sulfides to sulfoxides and amines to N-oxides. The deoxygenation reactions of sulfoxides to sulfides and reduction of nitro compounds to amines are fundamental reactions in both chemistry and biology. Here, we also highlight the catalysis of metal nanoparticles on the deoxygenation of sulfoxides and sulfones and reduction of nitro compounds with particular emphasis on the mechanistic aspects.

  10. Tris(bipyridineMetal(II-Templated Assemblies of 3D Alkali-Ruthenium Oxalate Coordination Frameworks: Crystal Structures, Characterization and Photocatalytic Activity in Water Reduction

    Alla Dikhtiarenko

    2016-02-01

    Full Text Available A series of 3D oxalate-bridged ruthenium-based coordination polymers with the formula of {[ZII(bpy3][MIRu(C2O43]}n (ZII = Zn2+ (1, Cu2+ (3, 4, Ru2+ (5, 6, Os2+ (7, 8; MI = Li+, Na+; bpy = 2,2’-bipyridine and {[ZnII(bpy3](H2O[LiRu(C2O43]}n (2 has been synthesized at room temperature through a self-assembly reaction in aqueous media and characterized by single-crystal and powder X-ray diffraction, elemental analysis, infrared and diffuse reflectance UV–Vis spectroscopy and thermogravimetric analysis. The crystal structures of all compounds comprise chiral 3D honeycomb-like polymeric nets of the srs-type, which possess triangular anionic cages where [ZII(bpy3]2+ cationic templates are selectively embedded. Structural analysis reveals that the electronic configuration of the cationic guests is affected by electrostatic interaction with the anionic framework. Moreover, the MLCT bands gaps values for 1–8 can be tuned in a rational way by judicious choice of [ZII(bpy3]2+ guests. The 3D host-guest polymeric architectures can be used as self-supported heterogeneous photocatalysts for the reductive splitting of water, exhibiting photocatalytic activity for the evolution of H2 under UV light irradiation.

  11. Ruthenium determination by the method of inversion voltammetry on graphite electrode

    Dominova, I G; Kolpakova, N A; Stromberg, A G [Tomskij Politekhnicheskij Inst. (USSR)

    1978-12-01

    Optimal conditions for determining ruthenium by inversion voltammetry on a graphite electrode are 0.1 M KCl or KNO/sub 3/, pH 2-3, electrolysis potential - 1.0 V. A linear dependence of ruthenium electrodissolution current on its concentration in the solution makes it possible to use inversion voltammetry for determining 5x10/sup -7/ - 1x10/sup -4/ g-ion Ru/l. Ruthenium can be determined in the presence of a large excess of nickel and copper but commensurable amounts of mercury adn platinum metals interfere.

  12. Oxidation of ruthenium thin films using atomic oxygen

    McCoy, A.P.; Bogan, J.; Brady, A.; Hughes, G.

    2015-12-31

    In this study, the use of atomic oxygen to oxidise ruthenium thin films is assessed. Atomic layer deposited (ALD) ruthenium thin films (~ 3 nm) were exposed to varying amounts of atomic oxygen and the results were compared to the impact of exposures to molecular oxygen. X-ray photoelectron spectroscopy studies reveal substantial oxidation of metallic ruthenium films to RuO{sub 2} at exposures as low as ~ 10{sup 2} L at 575 K when atomic oxygen was used. Higher exposures of molecular oxygen resulted in no metal oxidation highlighting the benefits of using atomic oxygen to form RuO{sub 2}. Additionally, the partial oxidation of these ruthenium films occurred at temperatures as low as 293 K (room temperature) in an atomic oxygen environment. - Highlights: • X-ray photoelectron spectroscopy study of the oxidation of Ru thin films • Oxidation of Ru thin films using atomic oxygen • Comparison between atomic oxygen and molecular oxygen treatments on Ru thin films • Fully oxidised RuO{sub 2} thin films formed with low exposures to atomic oxygen.

  13. Flameless atomic absorption determination of ruthenium using a ''Saturn-1'' spectrophotometer

    Pichkov, V.N.; Sinitsyn, N.M.; Sadikova, F.G.; Govorova, M.I.; Yakshinskij, A.I.

    1980-01-01

    A flameless atomic absorption method is suggested for determining ruthenium in samples of complicated composition using a ''Saturn-1'' spectrophotometer with a L'vov graphite cuvette. The method was used for determining ruthenium in a copper-based sample (10 -3 % Ru) and in electrolyte slurries (10 -3 -10 -2 %). The limit of detection Csub(min, 0.95) = 3.0x10 -3 μg Ru/ml. Other platinum metals do not interfere [ru

  14. A thermodynamic/mass-transport model for the release of ruthenium from irradiated fuel

    Garisto, F.; Iglesias, F.C.; Hunt, C.E.L.

    1990-01-01

    Some postulated nuclear reactor accidents lead to fuel failures and hence release of fission products into the primary heat transport system (PHTS). To determine the consequences of such accidents, it is important to understand the behavior of fission products both in the PHTS and in the reactor containment building. Ruthenium metal has a high boiling point and is nonvolatile under reducing conditions. However, under oxidizing conditions ruthenium can form volatile oxides at relatively low temperatures and, hence, could escape from failed fuel and enter the containment building. The ruthenium radioisotope Ru-106 presents a potentially significant health risk if it is released outside the reactor containment building. Consequently, it is important to understand the behavior of ruthenium during a nuclear reactor accident. The authors review the thermodynamic behavior of ruthenium at high temperatures. The qualitative behavior of ruthenium, predicted using thermodynamic calculations, is then compared with experimental results from the Chalk River Nuclear Laboratories (CRNL). Finally, a simple thermodynamic/mass-transport model is proposed to explain the release behavior of ruthenium in a steam atmosphere

  15. An XPS study on ruthenium compounds and catalysts

    Bianchi, C.L.; Ragaini, V.; Cattania, M.G.

    1991-01-01

    The binding energy (BE) of the relevant peaks of several ruthenium compounds have been measured with a monochromatic small spot XPS. The BE of the 3d 5/2 level of ruthenium is in the range 279.91-282.88 eV. The variation of BE is due either to the variation of the oxidation state or to the different counter-ion. A series of catalysts with varying amounts of ruthenium supported on alumina and prepared using different precursors was also analyzed. The presence of more ruthenium species other than the metal was observed. On the basis of the values previously obtained on unsupported compounds, the species with higher BE were assigned to oxides. On all the samples prepared from RuCl 3 , an additional peak at a very high BE (283.79 eV) has been observed. This peak is related to the presence of chlorine on the surface: it is suggested that it is related to a charge transfer interaction. The influence of this species on the CO reactivity in the Fischer-Tropsch reaction is discussed. (orig.)

  16. Dendrimer-Encapsulated Ruthenium Nanoparticles as Catalysts for Lithium-O2 Batteries

    Bhattacharya, Priyanka; Nasybulin, Eduard N.; Engelhard, Mark H.; Kovarik, Libor; Bowden, Mark E.; Li, Shari; Gaspar, Daniel J.; Xu, Wu; Zhang, Jiguang

    2014-12-01

    Dendrimer-encapsulated ruthenium nanoparticles (DEN-Ru) have been used as catalysts in lithium-O2 batteries for the first time. Results obtained from UV-vis spectroscopy, electron microscopy and X-ray photoelectron spectroscopy show that the nanoparticles synthesized by the dendrimer template method are ruthenium oxide instead of metallic ruthenium reported earlier by other groups. The DEN-Ru significantly improve the cycling stability of lithium (Li)-O2 batteries with carbon black electrodes and decrease the charging potential even at low catalyst loading. The monodispersity, porosity and large number of surface functionalities of the dendrimer template prevent the aggregation of the ruthenium nanoparticles making their entire surface area available for catalysis. The potential of using DEN-Ru as stand-alone cathode materials for Li-O2 batteries is also explored.

  17. Thermodynamic behaviour of ruthenium at high temperatures

    Garisto, F.

    1988-01-01

    Thermodynamic equilibrium calculations are used to determine the chemical speciation of ruthenium under postulated reactor accident conditions. The speciation of ruthenium is determined for various values of temperature, pressure, oxygen partial pressure and ruthenium concentration. The importance of these variables, in particular the oxygen partial pressure, in determining the volatility of ruthenium is clearly demonstrated in this report. Reliable thermodynamic data are required to determine the behaviour of ruthenium using equilibrium calculations. Therefore, it was necessary to compile a thermodynamic database for the ruthenium species that can be formed under reactor accident conditions. The origin of the thermodynamic data for the ruthenium species included in our calculations is discussed in detail in Appendix A. 23 refs

  18. Quantum chemical studies on electronic structure and photodynamics of ruthenium complexes

    Freitag, L.

    2015-01-01

    Ruthenium complexes have found their way into many applications in the last decades. Among those, ruthenium polypyridyl compounds have been employed as light harvesting devices and photosensitisers in artificial photosynthesis and molecular photocatalysis. Ruthenium nitrosyl complexes are rapidly emerging as NO delivery agents to biological tissues with promising applications in anticancer photodynamic therapy, thanks to their ability to photorelease nitric oxide (NO). This thesis encompasses computational studies on reactivity, electronic structure, excited states and photodynamics of several ruthenium nitrosyl and polypyridyl complexes. The first part of the thesis deals with ruthenium nitrosyls. The cis-trans isomerisation mechanism of RuHIndNO, a ruthenium nitrosyl derivate of the prominent anti-cancer drug candidate KP1019, is investigated with density functional theory calculations. Next, the electronic structure of the ground and the first excited triplet state of RuHIndNO is studied with multiconfigurational methods including the density-matrix renormalisation group (DMRG). The obtained multiconfigurational wavefunctions and DMRG-based orbital entanglement analysis provides theoretical insight into the non-innocence of the NO ligand in nitrosyl complexes by describing the electron correlation in the Ru--NO bond and assigning oxidation states to the metal and the NO ligand. Another study is performed on excited states of ruthenium nitrosyl complexes with quantum chemical calculations and surface-hopping dynamics to obtain insights into the photodissociation mechanism of NO. The second part of this thesis is devoted to the excited states and photophysics of ruthenium polypyridyl complexes. Accurate excitation energies of tris(2,2-bipyridine)ruthenium (II), the prototype ruthenium polypyridyl are obtained with multiconfigurational calculations assisted by an orbital entanglement analysis. Subsequently, the effect of the ligand substitution on the photophysics

  19. Reactions of ruthenium and osmium cluster carbonyls with heteroatom-substituted and functionalized alkynes

    Koridze, A.A.

    2000-01-01

    The results of studies of the reactions of ruthenium and osmium cluster carbonyls with metal (M = Re, Mn, Fe) alkynes, silylalkynes, propargyl alcohols and their derivatives, diynes, enynes, and ferrocenylacetylene are summarized. Intramolecular rearrangements in the cluster complexes including migrations of carbonyl, hydride, and hydrocarbon ligands and the metal core reorganization are considered [ru

  20. USDA-FSA-APFO Dugutak Ortho Mosaic

    Federal Emergency Management Agency, Department of Homeland Security — This data set contains imagery from the National Agricultural Imagery Program (NAIP). NAIP acquires digital ortho imagery during the agricultural growing seasons in...

  1. USDA-FSA-APFO Digital Ortho Mosaic

    Federal Emergency Management Agency, Department of Homeland Security — This data set contains imagery from the National Agricultural Imagery Program (NAIP). NAIP acquires digital ortho imagery during the agricultural growing seasons in...

  2. NAIP Digital Ortho Photo Image 2010

    Kansas Data Access and Support Center — This data set contains imagery from the National Agriculture Imagery Program (NAIP). NAIP acquires digital ortho imagery during the agricultural growing seasons in...

  3. Activity and selectivity regulation of synthesis gas reaction over supported ruthenium catalysts

    Fujimoto, K; Nobusawa, T; Fukushima, T; Tominaga, H

    1985-01-01

    The catalytic activities of supported ruthenium for synthesis-gas conversion to hydrocarbons was found to be in the following order: TiOS > Nb2O3 > ZrO2 > SiO2 > Ta2O5 > Al2O3 > V2O5 > MoO3 > WO3 > MnO2 > ZnO. Turnover frequencies of the supported ruthenium increased with decrease in dispersion of the metal particles for every carrier material. Even the activities per unit weight of metals were higher for low-dispersion ruthenium of Al2O3, TiO2, and ZrO2. The chain-growth probability of a hydrocarbon product, which is characterized by the Schulz-Flory distribution, increased markedly with decrease in the metal dispersion irrespective of the carrier material. The catalytic activity of ruthenium particles with a dispersed ruthenium increased almost linearly with an increase in reaction pressure (up to at least 2.0 MPa). 23 references, 10 figures, 3 tables.

  4. Complexing of zirconium and hafnium with ortho-aminobenzoic acid and paraaminobenzoic acid

    Alekseeva, I.I.; Nemzer, I.I.; Yuranova, L.I.; Borisova, V.V.; Prozorovskaya, Z.N.

    1977-01-01

    Formation of complexes between zirconium and hafnium and ortho- and para-aminobenzoic acids has been studied by the kinetic method. It has been found that at pH=1.3-2.0 and concentrations of metals 10 -5 -10 -6 mole complex compounds are formed with composition Me:L=1:2 and 1:1 (Me=Zr, Hf; L=ortho- or para-aminobenzoic acids). Stepwise constants and overall effective constants of complex formation have been calculated

  5. Ruthenium(II)-catalysed remote C-H alkylations as a versatile platform to meta-decorated arenes

    Li, Jie; Korvorapun, Korkit; de Sarkar, Suman; Rogge, Torben; Burns, David J.; Warratz, Svenja; Ackermann, Lutz

    2017-06-01

    The full control of positional selectivity is of prime importance in C-H activation technology. Chelation assistance served as the stimulus for the development of a plethora of ortho-selective arene functionalizations. In sharp contrast, meta-selective C-H functionalizations continue to be scarce, with all ruthenium-catalysed transformations currently requiring difficult to remove or modify nitrogen-containing heterocycles. Herein, we describe a unifying concept to access a wealth of meta-decorated arenes by a unique arene ligand effect in proximity-induced ruthenium(II) C-H activation catalysis. The transformative nature of our strategy is mirrored by providing a step-economical entry to a range of meta-substituted arenes, including ketones, acids, amines and phenols--key structural motifs in crop protection, material sciences, medicinal chemistry and pharmaceutical industries.

  6. Solventless synthesis of ruthenium nanoparticles

    García-Peña, Nidia G. [Departmento de Tecnociencias, Universidad Nacional Autónoma de México, Centro de Ciencias Aplicadas y Desarrollo Tecnológico, Universidad Nacional Autónoma de México, Cd. Universitaria A.P. 70-186, C.P. 04510 Coyoacán, México D.F. (Mexico); Redón, Rocío, E-mail: rredon@unam.mx [Departmento de Tecnociencias, Universidad Nacional Autónoma de México, Centro de Ciencias Aplicadas y Desarrollo Tecnológico, Universidad Nacional Autónoma de México, Cd. Universitaria A.P. 70-186, C.P. 04510 Coyoacán, México D.F. (Mexico); Herrera-Gomez, Alberto [Estudios Avanzados del Instituto Politécnico Nacional, Campus Juriquilla, Querétaro (Mexico); Fernández-Osorio, Ana Leticia [FES-Cuautitlán, Universidad Nacional Autónoma de México, Edo. de Mexico (Mexico); Bravo-Sanchez, Mariela; Gomez-Sosa, Gustavo [Estudios Avanzados del Instituto Politécnico Nacional, Campus Juriquilla, Querétaro (Mexico)

    2015-06-15

    Graphical abstract: - Highlights: • Successful synthesis of Ru nanoparticles by a cheap, fast and solventless approach was achieved. • The zero-valent state as well as the by-product/impurity free of the mechanochemical obtained Ru nanoparticles was proven by XPS, TEM and XRD. • Compared to two other synthesis strategies, the above-mentioned synthesis was more suitable to obtain smaller particles with fewer impurities in shorter time. - Abstract: This paper presents a novel solventless method for the synthesis of zero-valent ruthenium nanoparticles Ru(0). The proposed method, although not entirely new in the nanomaterials world, was used for the first time to synthesize zero-valent ruthenium nanoparticles. This new approach has proved to be an environmentally friendly, clean, cheap, fast, and reproducible technique which employs low amounts of solvent. It was optimized through varying amounts of reducing salt on a determined quantity of precursor and measuring the effect of this variation on the average particle size obtained. The resulting products were fully characterized by powder XRD, TEM, HR-TEM, and XPS studies, all of which corroborated the purity of the nanoparticles achieved. In order to verify the advantages of our method over other techniques, we compared our nanoparticles with two common colloidal-synthesized ruthenium nanoparticles.

  7. Spectrophotometric determination of ruthenium(III) and rhodium(III) after extraction of their cyclohexylthioglycolate complexes into chloroform

    Rao, A.L.J.; Gupta, Usha; Puri, B.K.

    1986-01-01

    Cyclohexylthioglycolate has been used as a reagent for the spectrophotometric determination of ruthenium(III) and rhodium(III) after the extraction of their complexes into chloroform. Various parameters involved in the extraction have been studied and the composition of the extracted complex has been established in each instance. Ruthenium and rhodium complexes are extracted into chloroform in the pH ranges 5.0-9.0 and 9.0-12.5, respectively. The ruthenium complex absorbs strongly at 365 nm, whereas the rhodium complex shows a maximum absorption at 345 nm. Beer's law is obeyed over the concentration range 6-96 μg for ruthenium and 2-41 μg for rhodium in 10 ml of the chloroform solution. The molar absorptivities are 5.02 x 10 3 l mol -1 cm -1 for ruthenium and 1.60 x 10 4 l mol -1 cm -1 for rhodium. Ten replicate determinations on a sample solution containing 60.3 μg of ruthenium or 20.6 μg of rhodium gave mean absorbances of 0.300 and 0.320 with standard deviations of 0.0021 and 0.0025 and relative standard deviations of 0.70% and 0.78%, respectively. The interference of various ions has been studied and the method has been applied to the determination of the metals in various synthetic samples. Conditions have also been developed for the simultaneous determination of ruthenium and rhodium. (author)

  8. Spectrophotometric determination of ruthenium (III) and rhodium (III) with 9,10-phenanthrenequinone monoxime after extraction into molten naphthalene

    Wasey, A.; Bansal, R.K.; Puri, B.K.; Satake, Masatada.

    1983-01-01

    9,10-Phenanthrenequinone monoxime has been used as a reagent for the spectrophotometric determination of ruthenium(III) and rhodium(III) after extraction into molten naphthalene. The extracted mixture of the metal complex and naphthalene was dissolved in chloroform and ruthenium and rhodium were determined spectrophotometrically. Beer's law holds in the concentration range of 0.2-4.1 μg/cm 3 for ruthenium and 0.3-5.3 μg/cm 3 for rhodium in 10 cm 3 of the final solution. The molar absorptivities and Sandell sensitivities are calculated to be 9.70 x 10 3 l mol -1 cm -1 and 0.01 μg/cmsup(2 ) (660 nm) for ruthenium and 1.13 x 10 4 l mol -1 cm -1 and 0.009 μg/cm 2 (410 nm) for rhodium respectively. Aliquots containing 2.0 μg of ruthenium and 4.1 μg of rhodium give mean absorbances of 0.192 and 0.451 with standard deviations of 0.0017 and 0.0039, respectively. Interference of various ions has been studied and the method has been applied to the determination of ruthenium and rhodium in various synthetic mixtures. This procedure is also applied to the simultaneous determination of ruthenium and rhodium present together in a solution. (author)

  9. Towards PSII analogs driven by ruthenium photophysics

    Olsson, Jerry

    2002-01-01

    A number of model complexes have been prepared in an attempt to develop models for photosystem II (PSII) in green plants. As replacement for the chlorophyll photosensitizer, we have used Ru(ll) tris-2,2-bipyridyl or Ru(ll) bis-2,2';6',2 - terpyridyl complexes linked to a pendant 2,2'-bipyridyl or 2,2';6',2''-terpyridyl moieties via spacers of varying lengths. Manganese (ll) has been covalently linked to the pendant 2,2'-bipyridyl /2,2';6',2''-terpyridyl moieties. The use of different ruthenium centres and spacers has made it possible to make assumptions about the way and how easily manganese is coordinated through self-assembly to the pendant 2,2'-bipyridyl or 2,2';6',2''-terpyridyl groups. Several polynuclear complexes containing a photoactive centre (Ru(ll) tris-2,2'-bipyridine or Ru(ll) bis-2,2';6',2''-terpyridine) or other metal ions (Co 2+ , Fe 2+ , Mn 2= ) have been prepared and characterised. The main work has been focused on organic synthesis and characterisation of polypyridine ligands and coordinated to different metal centres. The complexes have been investigated electrochemically and photophysically. Several new phenol-based ligands have been prepared by organic synthetic methods and characterised by various different methods. (author)

  10. Surface and sub-surface thermal oxidation of ruthenium thin films

    Coloma Ribera, R.; van de Kruijs, Robbert Wilhelmus Elisabeth; Zoethout, E.; Yakshin, Andrey; Bijkerk, Frederik

    2014-01-01

    For next generation Extreme UV photolithography, multilayer coatings may require protective capping layers against surface contamination. Ruthenium, as a low-oxidation metal, is often used as a reference material. The oxidation behaviour of Ru thin films has been studied using X-ray reflectometry

  11. Ruthenium(II)- bipyridyl with extended π-system: Improved thermo ...

    aInorganic and Physical Chemistry Division, Indian Institute of Chemical Technology, Uppal Road, Tarnaka, ... A new extended thermo-stable high molar extinction coefficient bipyridyl ruthenium(II) complex ... cyanines and metal free organic sensitizers have been ..... Iodide-based ionic liquids are more viscous than.

  12. Selective deposition of nanostructured ruthenium oxide using Tobacco mosaic virus for micro-supercapacitors in solid Nafion electrolyte

    Gnerlich, Markus; Ben-Yoav, Hadar; Culver, James N.; Ketchum, Douglas R.; Ghodssi, Reza

    2015-10-01

    A three-dimensional micro-supercapacitor has been developed using a novel bottom-up assembly method combining genetically modified Tobacco mosaic virus (TMV-1Cys), photolithographically defined micropillars and selective deposition of ruthenium oxide on multi-metallic microelectrodes. The three-dimensional microelectrodes consist of a titanium nitride current collector with two functionalized areas: (1) gold coating on the active electrode area promotes TMV-1Cys adhesion, and (2) sacrificial nickel pads dissolve in ruthenium tetroxide plating solution to produce ruthenium oxide on all electrically connected areas. The microfabricated electrodes are arranged in an interdigitated pattern, and the capacitance per electrode has been measured as high as 203 mF cm-2 with solid Nafion electrolyte. The process integration of bio-templated ruthenium oxide with microfabricated electrodes and solid electrolyte is an important advance towards the energy storage needs of mass produced self-sufficient micro-devices.

  13. Utilization of ruthenium volatilization at heating of residue containing phosphates and nitrates for ruthenium separation and for its qualitative proof

    Holgye, Z.

    1979-01-01

    The volatility of ruthenium during the heating of a residue after evaporation of a solution containing ruthenium, phosphates and nitrates may be utilized for the separation of ruthenium from various substances. Sup(103,106) Ru may be rapidly, selectively, and quantitatively separated from fission products mixture. Ruthenium may be also separated in this way from various inorganic salts or from biological material. The volatility of ruthenium may be used also for its qualitative proof. (author)

  14. Caprolactone-based bipyridine macroligands for novel ruthenium polypyridyl complexes for applications in dye-sensitized solar cells

    Marin, V.N.; Holder, E.; Hoogenboom, R.; Schubert, U.S.

    2004-01-01

    In an attempt to reduce electrolyte loss in solar cells, the use of sold or quasi-solid state electrolytes is advantageous. The authors synthesized a metal contg. polymer via two synthetic pathways. In the first, a bipyridine-bisphenanthroline ruthenium metal complex with a hydroxy functionality was

  15. Ammonia synthesis in the presence of rhodium-ruthenium-iridium carbonyl clusters

    Fedoseev, I.V.; Solov'ev, N.V.

    2007-01-01

    Researches in the field of platinum metal coordination compounds, where nitrogen enters as a ligand in coordination sphere of metal, are discussed. Results of experiments on the ammonia synthesis during the CO+N 2 mixture passing through alkali solution containing mixture of carbonyl clusters of rhodium, ruthenium and iridium at atmospheric pressure are given. Technique of the experiment and steps of assumed reactions of nitrogen fixation by Rh, Ir and Ru carbonyl clusters are demonstrated [ru

  16. Interface behaviour and electrical performance of ruthenium ...

    Rutherford backscattering spectrometry; Raman spectroscopy; oxidation; silicide; Schottky barrier diodes; ruthenium ... water and then dried with nitrogen gas before being loaded into the vacuum ... laser of wavelength 514.6 nm. Full I–V and ...

  17. Biological properties of novel ruthenium- and osmium-nitrosyl complexes with azole heterocycles

    Novak, Maria S.; Bü chel, Gabriel E.; Keppler, Bernhard K.; Jakupec, Michael A.

    2016-01-01

    Since the discovery that nitric oxide (NO) is a physiologically relevant molecule, there has been great interest in the use of metal nitrosyl compounds as antitumor pharmaceuticals. Particularly interesting are those complexes which can deliver NO to biological targets. Ruthenium- and osmium-based compounds offer lower toxicity compared to other metals and show different mechanisms of action as well as different spectra of activity compared to platinum-based drugs. Novel ruthenium- and osmium-nitrosyl complexes with azole heterocycles were studied to elucidate their cytotoxicity and possible interactions with DNA. Apoptosis induction, changes of mitochondrial transmembrane potential and possible formation of reactive oxygen species were investigated as indicators of NO-mediated damage by flow cytometry. Results suggest that ruthenium- and osmium-nitrosyl complexes with the general formula (indazolium)[cis/trans-MCl4(NO)(1H-indazole)] have pronounced cytotoxic potency in cancer cell lines. Especially the more potent ruthenium complexes strongly induce apoptosis associated with depolarization of mitochondrial membranes, and elevated reactive oxygen species levels. Furthermore, a slight yet not unequivocal trend to accumulation of intracellular cyclic guanosine monophosphate attributable to NO-mediated effects was observed.

  18. Biological properties of novel ruthenium- and osmium-nitrosyl complexes with azole heterocycles

    Novak, Maria S.

    2016-03-09

    Since the discovery that nitric oxide (NO) is a physiologically relevant molecule, there has been great interest in the use of metal nitrosyl compounds as antitumor pharmaceuticals. Particularly interesting are those complexes which can deliver NO to biological targets. Ruthenium- and osmium-based compounds offer lower toxicity compared to other metals and show different mechanisms of action as well as different spectra of activity compared to platinum-based drugs. Novel ruthenium- and osmium-nitrosyl complexes with azole heterocycles were studied to elucidate their cytotoxicity and possible interactions with DNA. Apoptosis induction, changes of mitochondrial transmembrane potential and possible formation of reactive oxygen species were investigated as indicators of NO-mediated damage by flow cytometry. Results suggest that ruthenium- and osmium-nitrosyl complexes with the general formula (indazolium)[cis/trans-MCl4(NO)(1H-indazole)] have pronounced cytotoxic potency in cancer cell lines. Especially the more potent ruthenium complexes strongly induce apoptosis associated with depolarization of mitochondrial membranes, and elevated reactive oxygen species levels. Furthermore, a slight yet not unequivocal trend to accumulation of intracellular cyclic guanosine monophosphate attributable to NO-mediated effects was observed.

  19. Ruthenium (4) and ruthenium (3) state in hydrochloric acid solutions under microwave irradiation

    Bashilov, A.V.; Kuz'min, N.M.; Nesterov, A.A.; Runov, V.K.

    2000-01-01

    Reactions of hydration, poly- and depolymerization, oxidation-reduction processes with ruthenium (4) and ruthenium (3) participation are investigated in hydrochloric acid solutions under microwave irradiation by the methods of molecular absorption spectroscopy in UV visible region taking K 4 [Ru 2 OCl 10 ] as an example. Content of state forms of ruthenium (4) and ruthenium (3), absorption characteristics of forming complexes are calculated. Variation of microwave irradiation parameters and HCl concentration permits to prepare solutions containing [RuCl 6 ] 2+ (95 %) and [(RuOH) 2 (H 2 O) 6 (OH) 2 ] 4+ (98 %) preeminently predominant forms. The role of microwave effect directly is established taking as an example the process of ruthenium (4) hydration [ru

  20. Cyclotron production of ruthenium-97 for radiopharmaceutical applications

    Music, S.; Gessner, M.

    1980-01-01

    Ruthenium-97 is of interest for clinical practice in nuclear medicine. The combination of the excellent physical and chemical properties of Ruthenium-97 make this isotope worth evaluating. Ruthenium-97 has been prepared by irradiation of a sheet of molybdenum with the internal alpha-beam of the Ruthenium-97 as a function of the alpha particle energy has been measured. The radiochemical separation and its possible clinical applications have been discussed. (author)

  1. Analysis of uranium and its compounds. Ruthenium spectrographic determination

    Anon.

    Ruthenium determination in uranium and its compounds, suitable for content greater than 0.1 ppm with respect to uranium, by dissolution in sulfuric acid and addition of palladium as an internal standard, separation of the precipitated ruthenium, in the presence of gold, by reduction with zinc, the precipitate is calcined and ruthenium is determined by spectrography [fr

  2. Method of suppressing evaporation loss of ruthenium

    Muromura, Tadazumi; Sato, Tadashi.

    1987-01-01

    Purpose: To prevent evaporation loss of ruthenium from liquid wastes by adding an aluminum compound upon applying evaporating and drying to solid treatment to reprocessing liquid wastes for spent fuels. Method: An aluminum compound such as aluminum nitrate or aluminum hydroxide to reprocessing liquid wastes of spent fuels such that aluminum/ruthenium mixing ratio corresponds to 1.3 - 70.0 by g/atom ratio (0.34 - 187 by weight ratio), and the liquid mixture is heated to a temperature of about 130 deg C to be evaporated and dried to solidness. This enables to recover ruthenium without settling and depositing insoluble matters in the liquid wastes and without decomposing nitric acid. (Yoshino, Y.)

  3. Inclusion Extraction of Alkali Metals by Emulsion Liquid Membranes and Nano-baskets of p-tert-Calix[4]arene Bearing Di-[N-(X)sulfonyl Carboxamide] and Di-(1-propoxy) in ortho-cone Conformation

    Mokhtari, Bahram; Pourabdollah, Kobra [Islamic Azad University, Province (Iran, Islamic Republic of)

    2012-05-15

    Nano-assisted inclusion separation of alkali metals from basic solutions was reported by inclusion-facilitated emulsion liquid membrane process. The novelty of this study is application of nano-baskets of calixarene in the selective and efficient separation of alkali metals as both the carrier and the surfactant. For this aim, four derivatives of p-tert-calix[4]arene bearing different sulfonamide moieties were synthesized and their inclusionextraction parameters were optimized including the calixarene scaffold 3 (4 wt %) as the carrier/demulsifier, the commercial kerosene as diluent in membrane, sulphonic acid (0.2 M) and ammonium carbonate (0.4 M) as the strip and the feed phases, the phase and the treat ratios of 0.8 and 0.3, mixing speed (300 rpm), and initial solute concentration (100 mg/L). The selectivity of membrane over more than ten interfering cations was examined and the results reveled that under the optimized operating condition, the degree of inclusionextraction of alkali metals was as high as 98-99%.

  4. Inclusion Extraction of Alkali Metals by Emulsion Liquid Membranes and Nano-baskets of p-tert-Calix[4]arene Bearing Di-[N-(X)sulfonyl Carboxamide] and Di-(1-propoxy) in ortho-cone Conformation

    Mokhtari, Bahram; Pourabdollah, Kobra

    2012-01-01

    Nano-assisted inclusion separation of alkali metals from basic solutions was reported by inclusion-facilitated emulsion liquid membrane process. The novelty of this study is application of nano-baskets of calixarene in the selective and efficient separation of alkali metals as both the carrier and the surfactant. For this aim, four derivatives of p-tert-calix[4]arene bearing different sulfonamide moieties were synthesized and their inclusionextraction parameters were optimized including the calixarene scaffold 3 (4 wt %) as the carrier/demulsifier, the commercial kerosene as diluent in membrane, sulphonic acid (0.2 M) and ammonium carbonate (0.4 M) as the strip and the feed phases, the phase and the treat ratios of 0.8 and 0.3, mixing speed (300 rpm), and initial solute concentration (100 mg/L). The selectivity of membrane over more than ten interfering cations was examined and the results reveled that under the optimized operating condition, the degree of inclusionextraction of alkali metals was as high as 98-99%

  5. In-situ XPS analysis of oxidized and reduced plasma deposited ruthenium-based thin catalytic films

    Balcerzak, Jacek; Redzynia, Wiktor; Tyczkowski, Jacek

    2017-12-01

    A novel in-situ study of the surface molecular structure of catalytically active ruthenium-based films subjected to the oxidation (in oxygen) and reduction (in hydrogen) was performed in a Cat-Cell reactor combined with a XPS spectrometer. The films were produced by the plasma deposition method (PEMOCVD). It was found that the films contained ruthenium at different oxidation states: metallic (Ru0), RuO2 (Ru+4), and other RuOx (Ru+x), of which content could be changed by the oxidation or reduction, depending on the process temperature. These results allow to predict the behavior of the Ru-based catalysts in different redox environments.

  6. Adsorption of aliphatic alcohols on ruthenium

    Shapovalova, L.B.; Zakumbaeva, G.D.

    1977-01-01

    The adsorption is studied of allyl-, propyl- and propargyl alcohols on a ruthenium catalyst-electrode at 20, 30 and 40 deg C in H 2 SO 4 in helium. Above adsorption has been found to grow with increased concentration of the alcohols in the solution. In solutions with the same concentration, propargyl alcohol has been noted to show highest sorptive capacity, followed by that of allyl- and propyl alcohols. With variations in the ruthenium electrode potential, alcohol adsorption occurs via maximum at potential = 0.18

  7. Processing of radioactive ruthenium with aluminosilicate gels

    Kanno, Takuji; Ichinose, Yasuhiro; Ito, Katsuo

    1979-01-01

    Coprecipitation of radioactive Ru with hydroxides has been studied for the purpose of the management of the high level waste from the nuclear fuel reprocessing. Aluminosilicate gel used as coprecipitant was prepared by addition of aqueous sodium hydroxide to sodium aluminate-sodium silicate solution containing ruthenium nitrate. Ruthenium quantitatively precipitates under the conditions, aluminate > 4 x 10 -2 M, Al/Si 0 C. However, volatilization rate of Ru is suppressed by coating with mullite phase into which aluminosilicate gel transformes above 900 0 C. The amount of Ru volatilized in Ar-flow was reduced to about 10% of that in air-flow. (author)

  8. A mixed ruthenium polypyridyl complex containing a PEG-bipyridine macroligand

    Marin, Veronica; Holder, Elisabeth; Meier, Michael A.R.; Hoogenboom, Richard; Schubert, Ulrich S. [Laboratory of Macromolecular Chemistry and Nanoscience, Eindhoven University of Technology and Dutch Polymer Institute (DPI), P. O. Box 513, 5600 MB Eindhoven (Netherlands)

    2004-04-06

    An amino-functionalized bipyridine ligand was prepared in order to serve as a bridging unit to an activated low-molecular-weight monomethyl ether of poly(ethylene glycol) (PEG). Coordination of a ruthenium(II) phenantroline precursor onto the formed PEG-containing bipyridine ligand yielded a metal-containing polymer which shows interesting properties for solar cell applications. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

  9. Synergistic Interaction within Bifunctional Ruthenium Nanoparticle/SILP Catalysts for the Selective Hydrodeoxygenation of Phenols.

    Luska, Kylie L; Migowski, Pedro; El Sayed, Sami; Leitner, Walter

    2015-12-21

    Ruthenium nanoparticles immobilized on acid-functionalized supported ionic liquid phases (Ru NPs@SILPs) act as efficient bifunctional catalysts in the hydrodeoxygenation of phenolic substrates under batch and continuous flow conditions. A synergistic interaction between the metal sites and acid groups within the bifunctional catalyst leads to enhanced catalytic activities for the overall transformation as compared to the individual steps catalyzed by the separate catalytic functionalities. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Two new ortho benzoquinones from Uncaria rhynchophylla.

    Zhang, Qian; Chen, Lei; Hu, Le-Jian; Liu, Wen-Yuan; Feng, Feng; Qu, Wei

    2016-03-01

    The present study was designed to determine the chemical constituents of the stems and hooks of Uncaria rhynchophylla. The chemical constituents were isolated and purified from CH2Cl2 fraction by chromatography. Their structures were elucidated by spectroscopic analyses. Their cytotoxicity was tested using MTT method. Two new ortho benzoquinones, 3-diethylamino-5-methoxy-1, 2-benzoquinone (1) and 3-ethylamino-5-methoxy-1, 2-benzoquinone (2), together with a known compound isorhynchophyllic acid (3) were isolated from U. rhynchophylla. These compounds were evaluated for their cytotoxicity against cancer cells A549, HepG2 and A2780. Compounds 1 and 2 were new ortho benzoquinones and showed weak antiproliferative activities on A549, HepG2 and A2780 cells. Compound 3 significantly inhibited the proliferation of A549, HepG2 and A2780 cells with IC50 values being 5.8, 12.8 and 11.8 µmol·L(-1), respectively. Copyright © 2016 China Pharmaceutical University. Published by Elsevier B.V. All rights reserved.

  11. Synthesis and reactivity of compounds containing ruthenium-carbon, -nitrogen, and -oxygen bonds

    Hartwig, J.F.

    1990-12-01

    The products and mechanisms of the thermal reactions of several complexes of the general structure (PMe 3 ) 4 Ru(X)(Y) and (DMPM) 2 Ru(X)(Y) where X and Y are hydride, aryl, and benzyl groups, have been investigated. The mechanism of decomposition depends critically on the structure of the complex and the medium in which the thermolysis is carried out. The alkyl hydride complexes are do not react with alkane solvent, but undergo C-H activation processes with aromatic solvents by several different mechanisms. Thermolysis of (PMe 3 ) 4 Ru(Ph)(Me) or (PMe 3 ) 4 Ru(Ph) 2 leads to the ruthenium benzyne complex (PMe 3 ) 4 Ru(η 2 -C 6 H 4 ) (1) by a mechanism which involves reversible dissociation of phosphine. In many ways its chemistry is analogous to that of early rather than late organo transition metal complexes. The synthesis, structure, variable temperature NMR spectroscopy and reactivity of ruthenium complexes containing aryloxide or arylamide ligands are reported. These complexes undergo cleavage of a P-C bond in coordinated trimethylphosphine, insertion of CO and CO 2 and hydrogenolysis. Mechanistic studies on these reactions are described. The generation of a series of reactive ruthenium complexes of the general formula (PMe 3 ) 4 Ru(R)(enolate) is reported. Most of these enolates have been shown to bind to the ruthenium center through the oxygen atom. Two of the enolate complexes 8 and 9 exist in equilibrium between the O- and C-bound forms. The reactions of these compounds are reported, including reactions to form oxygen-containing metallacycles. The structure and reactivity of these ruthenium metallacycles is reported, including their thermal chemistry and reactivity toward protic acids, electrophiles, carbon monoxide, hydrogen and trimethylsilane. 243 refs., 10 tabs

  12. Synthesis and reactivity of compounds containing ruthenium-carbon, -nitrogen, and -oxygen bonds

    Hartwig, J.F.

    1990-12-01

    The products and mechanisms of the thermal reactions of several complexes of the general structure (PMe{sub 3}){sub 4}Ru(X)(Y) and (DMPM){sub 2}Ru(X)(Y) where X and Y are hydride, aryl, and benzyl groups, have been investigated. The mechanism of decomposition depends critically on the structure of the complex and the medium in which the thermolysis is carried out. The alkyl hydride complexes are do not react with alkane solvent, but undergo C-H activation processes with aromatic solvents by several different mechanisms. Thermolysis of (PMe{sub 3}){sub 4}Ru(Ph)(Me) or (PMe{sub 3}){sub 4}Ru(Ph){sub 2} leads to the ruthenium benzyne complex (PMe{sub 3}){sub 4}Ru({eta}{sup 2}-C{sub 6}H{sub 4}) (1) by a mechanism which involves reversible dissociation of phosphine. In many ways its chemistry is analogous to that of early rather than late organo transition metal complexes. The synthesis, structure, variable temperature NMR spectroscopy and reactivity of ruthenium complexes containing aryloxide or arylamide ligands are reported. These complexes undergo cleavage of a P-C bond in coordinated trimethylphosphine, insertion of CO and CO{sub 2} and hydrogenolysis. Mechanistic studies on these reactions are described. The generation of a series of reactive ruthenium complexes of the general formula (PMe{sub 3}){sub 4}Ru(R)(enolate) is reported. Most of these enolates have been shown to bind to the ruthenium center through the oxygen atom. Two of the enolate complexes 8 and 9 exist in equilibrium between the O- and C-bound forms. The reactions of these compounds are reported, including reactions to form oxygen-containing metallacycles. The structure and reactivity of these ruthenium metallacycles is reported, including their thermal chemistry and reactivity toward protic acids, electrophiles, carbon monoxide, hydrogen and trimethylsilane. 243 refs., 10 tabs.

  13. Extraction and atomic absorption spectrophotometric determination of iron and ruthenium by using potassium xanthates

    Aihara, M; Kiboku, M [Kinki Univ., Higashi-Osaka, Osaka (Japan)

    1981-06-01

    Potassium xanthates (potassium o-alkyl dithiocarbonate; KRX) react with many metal ions, and so the complex formation with iron (II, III) ion and the extraction of their complexes has been studied to some extent, but those of ruthenium (III) have not been. Iron-xanthate and ruthenium-xanthate complexes can be extracted into methyl isobutyl ketone (MIBK) from weakly acidic solution to weakly alkaline solution. For quantitative extraction of iron (20 ..mu..g/40 ml), KRX concentration should be above 2.0 x 10/sup -2/ mol dm/sup -3/ of KEtX, 1.0 x 10/sup -2/ mol dm/sup -3/ of KPrX, and 5.0 x 10/sup -3/ mol dm/sup -3/ of KBtX and KPeX, and for that of ruthenium (202 ..mu..g/40 ml), it should be above 2.0 x 10/sup -1/ mol dm/sup -3/ of KEtX and KPrX. Formation constant of ruthenium-xanthate complexes is presumed to be small. A 100-fold excess of Ni(II), Co(II), Cu(II), WO/sub 4//sup 2 -/, PO/sub 4//sup 3 -/, CrO/sub 4//sup 2 -/, and Cr/sub 2/O/sub 7//sup 2 -/ interfered with the determination of iron, however, the interferences are eliminated by adding 5 ml of 0.1 mol dm/sup -3/ ascorbic acid solution. For the determination of ruthenium, a 50-fold excess of Ag(I), Hg(II), Pb(II), Zn(II), Mn(II), Cr(III), and Pt(II), or a 100-fold excess of NO/sub 2//sup -/, S/sub 2/O/sub 3//sup 2 -/, CrO/sub 4//sup 2 -/ and Cr/sub 2/O/sub 7//sup 2 -/, respectively, interfered. The coefficient of variation after each ten runs, ranges from 0.9% to 3.2% in the determination of 10 ..mu..g, 20 ..mu..g, and 30 ..mu..g of iron, and from 1.4% to 4.3% in the determination of 100 ..mu..g, 200 ..mu..g, and 300 ..mu..g of ruthenium. The determination limit in aqueous samples is 0.02 ppm for iron and 0.2 ppm for ruthenium, when the volume ratio of aqueous phase to organic phase (MIBK) is 10:1.

  14. Cathodic processes during ruthenium electrodeposition from a chloride melt

    Sokol'skij, D.V.

    1985-01-01

    Cathodic processes occurring during the electrolysis of chloride melts in the presence of oxygen-containing impurities were studied. The experiments were carried out at 500, 550 600 and 680 deg C, ruthenium ions concentration in KCl-NaCl-CsCl eutectic melt being 0.4-1.5 mol% and BaO additions 4.8x10 -2 mol%. Temperature dependence of Ru(3) ion diffusion coefficient in the chloride melt (lg D=3.25-1508/T+-0.02) and activation energy of the diffusion process (6.9 k cal/mol) were determined. It is shown that changes of the shape of E, t-curve and the deviation of values determined in the cause of chronopotentiometric investigations from the corresponding values of reversable processes are related in many respects to the participation of oxygen-containing compounds in the cathodic process. Irreversibility of the cathodic process is also connected with metal crystallization during electrodeposition

  15. Structure and reactivity of Ruthenium nanoparticles

    Gavnholt, Jeppe; Schiøtz, Jakob

    2008-01-01

    We present a method for obtaining detailed structural information of ruthenium nanoparticles in at least the diameter range from 1.5 to 5 nm. The method is based on an ensemble approach where a large number of low-energy structures are collected in an ensemble, from which average properties can...

  16. Thermodynamic properties of gaseous ruthenium species.

    Miradji, Faoulat; Souvi, Sidi; Cantrel, Laurent; Louis, Florent; Vallet, Valérie

    2015-05-21

    The review of thermodynamic data of ruthenium oxides reveals large uncertainties in some of the standard enthalpies of formation, motivating the use of high-level relativistic correlated quantum chemical methods to reduce the level of discrepancies. The reaction energies leading to the formation of ruthenium oxides RuO, RuO2, RuO3, and RuO4 have been calculated for a series of reactions. The combination of different quantum chemical methods has been investigated [DFT, CASSCF, MRCI, CASPT2, CCSD(T)] in order to predict the geometrical parameters, the energetics including electronic correlation and spin-orbit coupling. The most suitable method for ruthenium compounds is the use of TPSSh-5%HF for geometry optimization, followed by CCSD(T) with complete basis set (CBS) extrapolations for the calculation of the total electronic energies. SO-CASSCF seems to be accurate enough to estimate spin-orbit coupling contributions to the ground-state electronic energies. This methodology yields very accurate standard enthalpies of formations of all species, which are either in excellent agreement with the most reliable experimental data or provide an improved estimate for the others. These new data will be implemented in the thermodynamical databases that are used by the ASTEC code (accident source term evaluation code) to build models of ruthenium chemistry behavior in severe nuclear accident conditions. The paper also discusses the nature of the chemical bonds both from molecular orbital and topological view points.

  17. Enyne Metathesis Catalyzed by Ruthenium Carbene Complexes

    Poulsen, Carina Storm; Madsen, Robert

    2003-01-01

    Enyne metathesis combines an alkene and an alkyne into a 1,3-diene. The first enyne metathesis reaction catalyzed by a ruthenium carbene complex was reported in 1994. This review covers the advances in this transformation during the last eight years with particular emphasis on methodology...

  18. Support Effect in Hydrodesulfurization over Ruthenium Sulfide

    Gulková, Daniela; Kaluža, Luděk; Vít, Zdeněk; Zdražil, Miroslav

    2009-01-01

    Roč. 51, č. 2 (2009), s. 146-149 ISSN 1337-7027 R&D Projects: GA ČR GA104/06/0705 Institutional research plan: CEZ:AV0Z40720504 Keywords : ruthenium sulfide * hydrodesulfurization * support effect Subject RIV: CC - Organic Chemistry

  19. Ruthenium transport experiments in air ingress accident conditions

    Teemu, Karkele; Ulrika, Backman; Ari, Auvinen; Unto, Tapper; Jorma, Jokiniemi [VTT Technical Research Centre of Finland, Fine Particles (Finland); Riitta, Zilliacus; Maija, Lipponen; Tommi, Kekki [VTT Technical Research Centre of Finland, Accident Management (Finland); Jorma, Jokiniemi [Kuopio Univ., Dept. of Environmental Sciences, Fine Particle and Aerosol Technology Lab. (Finland)

    2007-07-01

    In this study the release, transport and speciation of ruthenium in conditions simulating an air ingress accident was studied. Ruthenium dioxide was exposed to oxidising environment at high temperature (1100-1700 K) in a tubular flow furnace. At these conditions volatile ruthenium species were formed. A large fraction of the released ruthenium was deposited in the tube as RuO{sub 2}. Depending on the experimental conditions 1-26 wt% of the released ruthenium was trapped in the outlet filter as RuO{sub 2} particles. In stainless steel tube 0-8.8 wt% of the released ruthenium reached the trapping bottle as gaseous RuO{sub 4}. A few experiments were carried out, in which revaporization of ruthenium deposited on the tube walls was studied. In these experiments, oxidation of RuO{sub 2} took place at a lower temperature. During revaporization experiments 35-65 % of ruthenium was transported as gaseous RuO{sub 4}. In order to close mass balance and achieve better time resolution 4 experiments were carried out using a radioactive tracer. In these experiments ruthenium profiles were measured. These experiments showed that the most important retention mechanism was decomposition of gaseous RuO{sub 3} into RuO{sub 2} as the temperature of the furnace was decreasing. In these experiments the transport rate of gaseous ruthenium was decreasing while the release rate was constant.

  20. High-pressure catalytic chemical vapor deposition of ferromagnetic ruthenium-containing carbon nanostructures

    Khavrus, Vyacheslav O., E-mail: V.Khavrus@ifw-dresden.de; Ibrahim, E. M. M.; Bachmatiuk, Alicja; Ruemmeli, Mark H.; Wolter, A. U. B.; Hampel, Silke; Leonhardt, Albrecht [IFW Dresden (Germany)

    2012-06-15

    We report on the high-pressure catalytic chemical vapor deposition (CCVD) of ruthenium nanoparticles (NPs) and single-walled carbon nanotubes (SWCNTs) by means of gas-phase decomposition of acetonitrile and ruthenocene in a tubular quartz flow reactor at 950 Degree-Sign C and at elevated pressures (between 2 and 8 bar). The deposited material consists of Ru metal cores with sizes ranging between 1 and 3 nm surrounded by a carbon matrix. The high-pressure CCVD seems to be an effective route to obtain composite materials containing metallic NPs, Ru in this work, inside a nanostructured carbon matrix protecting them from oxidation in ambient air. We find that in contradiction to the weak paramagnetic properties characterizing bulk ruthenium, the synthesized samples are ferromagnetic as predicted for nanosized particles of nonmagnetic materials. At low pressure, the very small ruthenium catalyst particles are able to catalyze growth of SWCNTs. Their yield decreases with increasing reaction pressure. Transmission electron microscopy, selected area energy-dispersive X-ray analysis, Raman spectroscopy, and magnetic measurements were used to analyze and confirm properties of the synthesized NPs and nanotubes. A discussion on the growth mechanism of the Ru-containing nanostructures is presented.

  1. Electrooxidative Ruthenium-Catalyzed C-H/O-H Annulation by Weak O-Coordination.

    Qiu, Youai; Tian, Cong; Massignan, Leonardo; Rogge, Torben; Ackermann, Lutz

    2018-05-14

    Electrocatalysis has been identified as a powerful strategy for organometallic catalysis, and yet electrocatalytic C-H activation is restricted to strongly N-coordinating directing groups. The first example of electrocatalytic C-H activation by weak O-coordination is presented, in which a versatile ruthenium(II) carboxylate catalyst enables electrooxidative C-H/O-H functionalization for alkyne annulations in the absence of metal oxidants; thereby exploiting sustainable electricity as the sole oxidant. Mechanistic insights provide strong support for a facile organometallic C-H ruthenation and an effective electrochemical reoxidation of the key ruthenium(0) intermediate. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Recent advances in the ruthenium-catalyzed hydroarylation of alkynes with aromatics: synthesis of trisubstituted alkenes.

    Manikandan, Rajendran; Jeganmohan, Masilamani

    2015-11-14

    The hydroarylation of alkynes with substituted aromatics in the presence of a metal catalyst via chelation-assisted C-H bond activation is a powerful method to synthesize trisubstituted alkenes. Chelation-assisted C-H bond activation can be done by two ways: (a) an oxidative addition pathway and (b) a deprotonation pathway. Generally, a mixture of cis and trans stereoisomeric as well as regioisomeric trisubstituted alkenes was observed in an oxidative addition pathway. In the deprotonation pathway, the hydroarylation reaction can be done in a highly regio- and stereoselective manner, and enables preparation of the expected trisubstituted alkenes in a highly selective manner. Generally, ruthenium, rhodium and cobalt complexes are used as catalysts in the reaction. In this review, a ruthenium-catalyzed hydroarylation of alkynes with substituted aromatics is covered completely. The hydroarylation reaction of alkynes with amide, azole, carbamate, phosphine oxide, amine, acetyl, sulfoxide and sulphur directed aromatics is discussed.

  3. Forefront of PUREX system engineering. Chemistry and engineering of ruthenium, technetium and neptunium

    2004-07-01

    The paper reports the activity of the research committee organized by the Atomic Energy Society of Japan on 'Ruthenium and Technetium Chemistry in the PUREX System', with focusing on basic behaviors of ruthenium, technetium and neptunium in the PUREX process, the principles of plant design, and behaviors during the final waste treatment. The scope of the work includes the following major topics: (1) basic solution and solid-state chemistry; (2) basic solution and solid-state chemistry of minor actinides in particular, Np; (3) partitioning chemistry in the PUREX system and environmental behavior of the components; (4) processes of recovery, purification, and utilization of rare metal fission products; (5) field data on plant design, operation, decontamination, and decommissioning; (6) numerical process simulations and process control technologies; (7) compilation of a data base for process chemistry and plant engineering. (S. Ohno)

  4. Contribution to the study of ruthenium fluorides, oxyfluorides and oxides

    Corbin, Odile.

    1982-08-01

    Studies on the dry processing of spent fuels reveal a poor ruthenium decontamination of plutonium. For a better understanding of this result a study of ruthenium fluorides, oxyfluorides and oxides is carried out here as follows: - bibliographical review; - thermochromatographic identification of the number and nature of compounds formed by fluorination of microquantities of ruthenium; - confirmation of the thermochromatographic results by two other analytical methods: thermogravimetry and infrared spectroscopy [fr

  5. Palladium-Catalyzed ortho C-H Arylation of Benzaldehydes Using ortho-Sulfinyl Aniline Transient Auxiliary.

    Mu, Delong; He, Gang; Chen, Gong

    2018-05-03

    A PdII-catalyzed ortho-(Csp2)-H arylation reaction of benzaldehydes using catalytic amount of 2-methylsulfinyl-aniline as transient auxiliary was developed. This reaction is compatible with a broad range of benzaldehyde and aryl iodide substrates. Compared with other related reaction systems, an excellent regioselectivity for ortho-C(sp2)-H bonds over benzylic C(sp3)-H bonds was obtained for ortho-alkyl-benzaldehyde substrates. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. 2010 NOAA Ortho-rectified Mosaic of Lake Champlain, Vermont

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  7. Aerial Photography and Imagery, Ortho-Corrected - DOQQ 1999 Orthophotography

    NSGIC Local Govt | GIS Inventory — 1999 Digital Ortho Quarter Quads. Acquired from SJRWMD (http://sjrwmd.com/). Flight Date Jan, 1999. Can be downloaded in DOQQ Format as JPEGS or MrSIDs from LABINS...

  8. 2012 NOAA Ortho-rectified Color Mosaic of Astoria, Oregon

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  9. 2011 NOAA Ortho-rectified Mosaic of Intracoastal Waterway, Texas

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  10. 2011 NOAA Ortho-rectified Mosaic of Galveston, Texas

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  11. Sweetening ruthenium and osmium: organometallic arene complexes containing aspartame.

    Gray, Jennifer C; Habtemariam, Abraha; Winnig, Marcel; Meyerhof, Wolfgang; Sadler, Peter J

    2008-09-01

    The novel organometallic sandwich complexes [(eta(6)-p-cymene)Ru(eta(6)-aspartame)](OTf)(2) (1) (OTf = trifluoromethanesulfonate) and [(eta(6)-p-cymene)Os(eta(6)-aspartame)](OTf)(2) (2) incorporating the artificial sweetener aspartame have been synthesised and characterised. A number of properties of aspartame were found to be altered on binding to either metal. The pK(a) values of both the carboxyl and the amino groups of aspartame are lowered by between 0.35 and 0.57 pH units, causing partial deprotonation of the amino group at pH 7.4 (physiological pH). The rate of degradation of aspartame to 3,6-dioxo-5-phenylmethylpiperazine acetic acid (diketopiperazine) increased over threefold from 0.12 to 0.36 h(-1) for 1, and to 0.43 h(-1) for 2. Furthermore, the reduction potential of the ligand shifted from -1.133 to -0.619 V for 2. For the ruthenium complex 1 the process occurred in two steps, the first (at -0.38 V) within a biologically accessible range. This facilitates reactions with biological reductants such as ascorbate. Binding to and activation of the sweet taste receptor was not observed for these metal complexes up to concentrations of 1 mM. The factors which affect the ability of metal-bound aspartame to interact with the receptor site are discussed.

  12. Ruthenium-Catalyzed Aerobic Oxidation of Amines.

    Ray, Ritwika; Hazari, Arijit Singha; Lahiri, Goutam Kumar; Maiti, Debabrata

    2018-01-18

    Amine oxidation is one of the fundamental reactions in organic synthesis as it leads to a variety of value-added products such as oximes, nitriles, imines, and amides among many others. These products comprise the key N-containing building blocks in the modern chemical industry, and such transformations, when achieved in the presence of molecular oxygen without using stoichiometric oxidants, are much preferred as they circumvent the production of unwanted wastes. In parallel, the versatility of ruthenium catalysts in various oxidative transformations is well-documented. Herein, this review focuses on aerobic oxidation of amines specifically by using ruthenium catalysts and highlights the major achievements in this direction and challenges that still need to be addressed. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Thermodynamic assessment of the rhodium-ruthenium-oxygen (Rh-Ru-O) system

    Gossé, S.; Bordier, S.; Guéneau, C.; Brackx, E.; Domenger, R.; Rogez, J.

    2018-03-01

    Ruthenium (Ru) and rhodium (Rh) are abundant platinum-group metals formed during burn-up of nuclear fuels. Under normal operating conditions, Rh and Ru accumulate and predominantly form metallic precipitates with other fission products like Mo, Pd and Tc. In the framework of vitrification of high-level nuclear waste, these fission products are poorly soluble in molten glasses. They precipitate as metallic particles and oxide phases. Moreover, these Ru and Rh rich phases strongly depend on temperature and the oxygen fugacity of the glass melt. In case of severe accidental conditions with air ingress, oxidation of the Ru and Rh is possible. At low temperatures (T 1422 K for rhodium sesquioxide and T > 1815 K for ruthenium dioxide), they may decompose into (Rh)-FCC or (Ru)-HCP metallic phases and radiotoxic volatile gaseous species. A thermodynamic assessment of the Rh-Ru-O system will enable the prediction of: (1) the metallic and oxide phases that form during the vitrification of high-level nuclear wastes and (2) the release of volatile gaseous species during a severe accident. The Calphad method developed herein employs a thermodynamic approach in the investigation of the thermochemistry of rhodium and ruthenium at high temperatures. Current literature on the thermodynamic properties and phase diagram data enables preliminary thermodynamic assessments of the Rh-O and Ru-O systems. Additionally, select compositions in the ternary Rh-Ru-O system underwent experimental tests to complement data found in literature and to establish the phase equilibria in the ternary system.

  14. A method for recovering and separating palladium, technetium, rhodium and ruthenium contained in solutions resulting from nuclear fuel recycling

    Moore, R.H.

    1974-01-01

    The invention relates to a method for recovering and separating technetium and metals of the platinum group, i.e. palladium, rhodium and ruthenium existing as fission products. The method according to the invention is characterized by contacting a residuary acid aqueous solution provided by nuclear fuel recycling with successive carbon beds which have adsorbed different chelating agents specific for the metals to be recovered in order that said metals be selectively chelated and extracted from the solution. This method is suitable for recovering the above metals from solutions provided by reprocessing spent fuels [fr

  15. Sequential Electrodeposition of Platinum-Ruthenium at Boron-Doped Diamond Electrodes for Methanol Oxidation

    Ileana González-González

    2011-01-01

    Full Text Available Sequential electrodeposition of Pt and Ru on boron-doped diamond (BDD films, in 0.5 M H2SO4 by cyclic voltammetry, has been prepared. The potential cycling, in the aqueous solutions of the respective metals, was between 0.00 and 1.00 V versus Ag/AgCl. The catalyst composites, Pt and PtRu, deposited on BDD film substrates, were tested for methanol oxidation. The modified diamond surfaces were also characterized by scanning electron microscopy-X-ray fluorescence-energy dispersive spectroscopy, X-ray photoelectron spectroscopy, and Auger electron spectroscopy. The scanning Auger electron spectroscopy mapping showed the ruthenium signal only in areas where platinum was electrodeposited. Ruthenium does not deposit on the oxidized diamond surface of the boron-doped diamond. Particles with 5–10% of ruthenium with respect to platinum exhibited better performance for methanol oxidation in terms of methanol oxidation peak current and chronoamperometric current stability. The electrogenerated •OH radicals on BDD may interact with Pt surface, participating in the methanol oxidation as shown in oxidation current and the shift in the peak position. The conductive diamond surface is a good candidate as the support for the platinum electrocatalyst, because it ensures catalytic activity, which compares with the used carbon, and higher stability under severe anodic and cathodic conditions.

  16. Ruthenium(II) carbonyl compounds with the 4'-chloro-2,2':6',2''-terpyridine ligand.

    Tatikonda, Rajendhraprasad; Haukka, Matti

    2017-04-01

    Two ruthenium carbonyl complexes with the 4'-chloro-2,2':6',2''-terpyridine ligand (tpy-Cl, C 15 H 10 ClN 3 ), i.e. [RuCl(tpy-Cl)(CO) 2 ][RuCl 3 (CO) 3 ] (I) [systematic name: cis -di-carbonyl-chlorido(4'-chloro-2,2':6',2''-terpyridine-κ 3 N )ruthenium(II) fac -tricarbonyltri-chlorido-ruthenate(II)], and [RuCl 2 (tpy-Cl)(CO) 2 ] (II) [ cis -dicarbonyl- trans -di-chlorido(4'-chloro-2,2':6',2''-terpyridine-κ 2 N 1 , N 1' )ruthenium(II)], were synthesized and characterized by single-crystal X-ray diffraction. The Ru II atoms in both centrosymmetric structures (I) and (II) display similar, slightly distorted octa-hedral coordination spheres. The coordination sphere in the complex cation in compound (I) is defined by three N atoms of the tridentate tpy-Cl ligand, two carbonyl carbon atoms and one chlorido ligand; the charge is balanced by an octa-hedral [Ru(CO) 3 Cl 3 ] - counter-anion. In the neutral compound (II), the tpy-Cl ligand coordinates to the metal only through two of its N atoms. The coordination sphere of the Ru II atom is completed by two carbonyl and two chlorido ligands. In the crystal structures of both (I) and (II), weak C-H⋯Cl inter-actions are observed.

  17. Characterization of self-assembled monolayers on a ruthenium surface

    Shaheen, Amrozia; Sturm, Jacobus Marinus; Ricciardi, R.; Huskens, Jurriaan; Lee, Christopher James; Bijkerk, Frederik

    2017-01-01

    We have modified and stabilized the ruthenium surface by depositing a self-assembled monolayer (SAM) of 1-hexadecanethiol on a polycrystalline ruthenium thin film. The growth mechanism, dynamics, and stability of these monolayers were studied. SAMs, deposited under ambient conditions, on

  18. Application of the chemical properties of ruthenium to decontamination processes

    Fontaine, A.; Berger, D.

    1965-01-01

    The chemical properties of ruthenium in the form of an aqueous solution of the nitrate and of organic tributylphosphate solution are reviewed. From this data, some known examples are given: they demonstrate the processes of separation or of elimination of ruthenium from radioactive waste. (authors) [fr

  19. Volatilization and trapping of ruthenium in high temperature processes

    Klein, M.; Weyers, C.; Goossens, W.R.A.

    1983-01-01

    This experimental study has indicated the importance of moisture and NO/sub x/ vapors on the volatility and trapping conditions of ruthenium in high temperature processes. Also the process operating conditions have a great influence on the ruthenium behavior in the off-gas purification units. Of particular interest is the observation that the ruthenium release during direct vitrification of simulated high-level liquid waste is a factor of about 5 smaller than the ruthenium release during calcination of this type of waste. Moreover, in the direct vitrification case the ruthenium escapes mostly in the form of an aerosol whereas in the calcination case a volatile ruthenium compound is dominating. Consequently, a specific ruthenium filter is not needed in the off-gas line of a direct vitrifier simplifying in this way the number of units in this off-gas line and avoiding the handling and controlling problems of such a ruthenium filter. In the future, a similar program will be started on the volatility of cesium and antimony in a liquid fed melter and on the technical reliability of the liquid fed melter and its associated gas purification units on a semi-pilote scale under simulated conditions

  20. The biokinetics of ruthenium in the human body

    Leggett, Richard Wayne

    2011-01-01

    The biokinetics of ruthenium (Ru) in the human body is of interest due mainly to the potential for occupational or environmental exposure to 106Ru (T1/2 = 373.6 d) and 103Ru (T1/2 = 39.3 d), which typically represent a significant portion of the fission products in a reactor inventory. During reactor operations or nuclear fuel reprocessing these ruthenium isotopes may be present as ruthenium tetroxide (RuO4) vapor, a highly mobile form of ruthenium that has been involved in a number of cases of accidental exposure to 106Ru or 103Ru. This paper summarizes the biokinetic database for ruthenium and proposes a new respiratory model for inhaled RuO4 vapor, a new biokinetic for systemic (absorbed) ruthenium, and material-specific gastrointestinal absorption fractions for ruthenium. The proposed respiratory model for RuO4 differs from the current ICRP model mainly in that it depicts slower clearance of deposited activity from the respiratory tract and lower absorption to blood than depicted in the current ICRP model. The proposed systemic biokinetic model depicts more realistic paths of movement of absorbed ruthenium in the body than the current ICRP model and, in contrast to the present model, a less uniform distribution of systemic activity. Implications of the proposed models with regard to inhalation and ingestion dose coefficients for 106Ru are examined.

  1. Bioimaging of isosteric osmium and ruthenium anticancer agents by LA-ICP-MS.

    Klose, Matthias H M; Theiner, Sarah; Kornauth, Christoph; Meier-Menches, Samuel M; Heffeter, Petra; Berger, Walter; Koellensperger, Gunda; Keppler, Bernhard K

    2018-03-01

    Laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) was used to study the spatial distribution of two metallodrugs with anticancer activities in vivo, namely the organoruthenium plecstatin-1 (1) and its isosteric osmium analogue (2), in liver, kidneys, muscles and tumours of treated mice bearing a CT-26 tumour after single-dose i.p. administration. To the best of our knowledge, this is the first time that the spatial distribution of an osmium drug candidate has been investigated using LA-ICP-MS in tissues. Independent measurements of the average ruthenium and osmium concentration via microwave digestion and ICP-MS in organs and tumours were in good agreement with the LA-ICP-MS results. Matrix-matched standards (MMS) ranging from 1 to 30 μg g -1 were prepared to quantify the spatial distributions of the metals and the average metal content of the MMS samples was additionally quantified by ICP-MS after microwave digestion. The recoveries for osmium and ruthenium in the MMS were 105% and 101% on average, respectively, validating the sample preparation procedure of the MMS. Preparation of MMS was carried out under an argon atmosphere to prevent oxidation of osmium-species to the volatile OsO 4 . The highest metal concentrations were found in the liver, followed by kidney, lung and tumour tissues, while muscles displayed only very low quantities of the respective metal. Both metallodrugs accumulated in the cortex of the kidneys more strongly compared to the medulla. Interestingly, osmium from 2 was largely located at the periphery and tissue edges, whereas ruthenium from 1 was observed to penetrate deeper into the organs and tumours.

  2. Isolation, Bioactivity, and Production of ortho-Hydroxydaidzein and ortho-Hydroxygenistein

    Te-Sheng Chang

    2014-04-01

    Full Text Available Daidzein and genistein are two major components of soy isoflavones. They exist abundantly in plants and possess multiple bioactivities. In contrast, ortho-hydroxydaidzein (OHD and ortho-hydroxygenistein (OHG, including 6-hydroxydaidzein (6-OHD, 8-hydroxydaidzein (8-OHD, 3'-hydroxydaidzein (3'-OHD, 6-hydroxygenistein (6-OHG, 8-hydroxygenistein (8-OHG, and 3'-hydroxygenistein (3'-OHG, are rarely found in plants. Instead, they are usually isolated from fermented soybean foods or microbial fermentation broth feeding with soybean meal. Accordingly, the bioactivity of OHD and OHG has been investigated less compared to that of soy isoflavones. Recently, OHD and OHG were produced by genetically engineering microorganisms through gene cloning of cytochrome P450 (CYP enzyme systems. This success opens up bioactivity investigation and industrial applications of OHD and OHG in the future. This article reviews isolation of OHD and OHG from non-synthetic sources and production of the compounds by genetically modified microorganisms. Several bioactivities, such as anticancer and antimelanogenesis-related activities, of OHD and OHG, are also discussed.

  3. Catalytic reduction of ruthenium tetroxide

    Nakhutin, I.E.; Polyakov, A.S.; Ananyan, O.S.; Blinnikov, S.A.; Kulakov, A.I.; Takmazyan, A.S.

    1978-01-01

    RuO 4 removal from the gaseous phase by reduction to solid RuO 2 with carbon oxide has been investigated. The reaction has been shown to be autocatalytic. A catalyst (RuO 2 on Al 2 O 3 ) for the reduction has been developed. There have been determined the region of reaction RuO 4 +CO on the catalyst containing RuO 2 , the temperature dependence of the decontamination factor and the reaction order in RuO 4 . The feasibility of RuO 4 thermal decomposition on the catalyst has been shown. A number of other metal oxides that can catalyze the process is listed

  4. Selective Catalytic Hydrogenation of Arenols by a Well-Defined Complex of Ruthenium and Phosphorus–Nitrogen PN3–Pincer Ligand Containing a Phenanthroline Backbone

    Li, Huaifeng; Wang, Yuan; Lai, Zhiping; Huang, Kuo-Wei

    2017-01-01

    Selective catalytic hydrogenation of aromatic compounds is extremely challenging using transition-metal catalysts. Hydrogenation of arenols to substituted tetrahydronaphthols or cyclohexanols has been reported only with heterogeneous catalysts. Herein, we demonstrate the selective hydrogenation of arenols to the corresponding tetrahydronaphthols or cyclohexanols catalyzed by a phenanthroline-based PN3-ruthenium pincer catalyst.

  5. Selective Catalytic Hydrogenation of Arenols by a Well-Defined Complex of Ruthenium and Phosphorus–Nitrogen PN3–Pincer Ligand Containing a Phenanthroline Backbone

    Li, Huaifeng

    2017-05-30

    Selective catalytic hydrogenation of aromatic compounds is extremely challenging using transition-metal catalysts. Hydrogenation of arenols to substituted tetrahydronaphthols or cyclohexanols has been reported only with heterogeneous catalysts. Herein, we demonstrate the selective hydrogenation of arenols to the corresponding tetrahydronaphthols or cyclohexanols catalyzed by a phenanthroline-based PN3-ruthenium pincer catalyst.

  6. Atomic layer deposition of ruthenium on plasma-treated vertically aligned carbon nanotubes for high-performance ultracapacitors.

    Kim, Jun Woo; Kim, Byungwoo; Park, Suk Won; Kim, Woong; Shim, Joon Hyung

    2014-10-31

    It is challenging to realize a conformal metal coating by atomic layer deposition (ALD) because of the high surface energy of metals. In this study, ALD of ruthenium (Ru) on vertically aligned carbon nanotubes (CNTs) was carried out. To activate the surface of CNTs that lack surface functional groups essential for ALD, oxygen plasma was applied ex situ before ALD. X-ray photoelectron spectroscopy and Raman spectroscopy confirmed surface activation of CNTs by the plasma pretreatment. Transmission electron microscopy analysis with energy-dispersive x-ray spectroscopy composition mapping showed that ALD Ru grew conformally along CNTs walls. ALD Ru/CNTs were electrochemically oxidized to ruthenium oxide (RuOx) that can be a potentially useful candidate for use in the electrodes of ultracapacitors. Electrode performance of RuOx/CNTs was evaluated using cyclic voltammetry and galvanostatic charge-discharge measurements.

  7. Ruthenium-platinum bimetallic catalysts supported on silica: characterization and study of benzene hydrogenation and CO methanation

    Chakrabarty, D.K.; Rao, K.M.; Sundararaman, N.; Chandavar, K.

    1986-12-15

    Ru-Pt/SiO/sub 2/ bimetallic catalysts with varying Ru:Pt ratio have been prepared and studied with the aim to establish if they contain coclusters or isolated ruthenium and platinum particles. X-ray diffraction studies show that individual crystallites of ruthenium and platinum are present and no coclusters are formed. Metal dispersion has been determined by hydrogen chemisorption and surface composition of the catalysts has been obtained from XPS. It was found that preoxidation of the catalysts prior to reduction is essential for good platinum dispersion. The experimental turnover number (TN) for benzene hydrogenation on the bimetallic catalysts agrees very well with that of the weighted average on the individual metal catalysts and this may be taken as a kinetic evidence for the absence of coclusters. Carbon monoxide methanation activity of the bimetallic catalysts is quite similar to that of the supported platinum catalyst. 6 refs., 6 figs., 2 tabs.

  8. Tailoring Ruthenium Exposure to Enhance the Performance of fcc Platinum@Ruthenium Core-Shell Electrocatalysts in the Oxygen Evolution Reaction

    AlYami, Noktan

    2016-05-17

    The catalytic properties of noble metal nanocrystals are a function of their size, structure, and surface composition. In particular, achieving high activity without sacrificing stability is essential for designing commercially viable catalysts. A major challenge in designing state-of-the-art Ru-based catalysts for the oxygen evolution reaction (OER), which is a key step in water splitting, is the poor stability and surface tailorability of these catalysts. In this study, we designed rapidly synthesizable size-controlled, morphology-selective, and surface-tailored platinum-ruthenium core-shell (Pt@Ru) and alloy (PtRu) nanocatalysts in a scalable continuous-flow reactor. These core-shell nanoparticles with atomically precise shells were produced in a single synthetic step with carbon monoxide as the reducing agent. By varying the metal precursor concentration, a dendritic or layer-by-layer ruthenium shell can be grown. The catalytic activities of the synthesized Pt@Ru and PtRu nanoparticles exhibit noticeably higher electrocatalytic activity in the OER compared to that of pure Pt and Ru nanoparticles. Promisingly, Pt@Ru nanocrystals with a ~2-3 atomic layer Ru cuboctahedral shell surpass conventional Ru nanoparticles in terms of both durability and activity.

  9. Tailoring Ruthenium Exposure to Enhance the Performance of fcc Platinum@Ruthenium Core-Shell Electrocatalysts in the Oxygen Evolution Reaction

    AlYami, Noktan; LaGrow, Alec P.; Joya, khurram; Hwang, Jinyeon; Katsiev, Khabiboulakh; Anjum, Dalaver H.; Losovyj, Yaroslav; Sinatra, Lutfan; Kim, Jin Young; Bakr, Osman

    2016-01-01

    The catalytic properties of noble metal nanocrystals are a function of their size, structure, and surface composition. In particular, achieving high activity without sacrificing stability is essential for designing commercially viable catalysts. A major challenge in designing state-of-the-art Ru-based catalysts for the oxygen evolution reaction (OER), which is a key step in water splitting, is the poor stability and surface tailorability of these catalysts. In this study, we designed rapidly synthesizable size-controlled, morphology-selective, and surface-tailored platinum-ruthenium core-shell (Pt@Ru) and alloy (PtRu) nanocatalysts in a scalable continuous-flow reactor. These core-shell nanoparticles with atomically precise shells were produced in a single synthetic step with carbon monoxide as the reducing agent. By varying the metal precursor concentration, a dendritic or layer-by-layer ruthenium shell can be grown. The catalytic activities of the synthesized Pt@Ru and PtRu nanoparticles exhibit noticeably higher electrocatalytic activity in the OER compared to that of pure Pt and Ru nanoparticles. Promisingly, Pt@Ru nanocrystals with a ~2-3 atomic layer Ru cuboctahedral shell surpass conventional Ru nanoparticles in terms of both durability and activity.

  10. Electrical transport properties of spray deposited transparent conducting ortho-Zn2SnO4 thin films

    Ramarajan, R.; Thangaraju, K.; Babu, R. Ramesh; Joseph, D. Paul

    2018-04-01

    Ortho Zinc Stannate (Zn2SnO4) exhibits excellent electrical and optical properties to serve as alternate transparent electrode in optoelectronic devices. Here we have optimized ortho-Zn2SnO4 thin film by spray pyrolysis method. Deposition was done onto a pre-heated glass substrate at a temperature of 400 °C. The XRD pattern indicated films to be polycrystalline with cubic structure. The surface of films had globular and twisted metal sheet like morphologies. Films were transparent in the visible region with band gap around 3.6 eV. Transport properties were studied by Hall measurements at 300 K. Activation energies were calculated from Arrhenius's plot from temperature dependent electrical measurements and the conduction mechanism is discussed.

  11. Density functional theory based QSAR study of ruthenium (II) antitumor drugs and their interactions with xanthine oxidoreductase

    Mondal, Paritosh; Das, Dharitri

    2013-01-01

    Transition metal containing drugs have been used intensely for their potential anticancer activities. Platinum drugs have been used successfully for the treatment of cancer. However, these drugs have severe drawbacks including unwanted side effects, drug resistance and ineffectiveness towards some of cancers. Therefore scientists are searching for new drugs to solve these problems, and Ruthenium coordination compounds have been found effective alternatives to platinum coordination drugs

  12. Energy expenditure during ambulation with ortho crutches and axillary crutches.

    Hinton, C A; Cullen, K E

    1982-06-01

    Thirteen normal male college students were studied during unassisted ambulation and nonweight-bearing ambulation with Ortho crutches and axillary crutches to determine energy expenditure. Subjects walked at self-selected velocities. Energy expenditure was determined by analyzing expired air collected by a calorimeter. Heart rate was monitored by telemetry. During the first 2.5 minutes of walking, heart rate and energy expenditure were significantly greater for ambulation with axillary crutches than with Ortho crutches. After 11.5 minutes of walking, no difference in energy cost was found between crutch types; however, heart rate increased significantly (p less than .01) during ambulation with axillary crutches. Differences in energy cost and heart rate were attributed to increased upper extremity work performed when using axillary crutches. We concluded that during nonweight-bearing ambulation for short periods of time or over a short distance, the Ortho crutch is less taxing in terms of energy cost and heart rate demands.

  13. Recent advances in the ruthenium(ii)-catalyzed chelation-assisted C-H olefination of substituted aromatics, alkenes and heteroaromatics with alkenes via the deprotonation pathway.

    Manikandan, Rajendran; Jeganmohan, Masilamani

    2017-08-08

    The transition-metal-catalyzed chelation-assisted alkenylation at the inert C-H bond of aromatics with alkenes is one of the efficient methods to synthesize substituted vinylarenes in a highly regio- and stereoselective manner. Palladium, rhodium and ruthenium complexes are frequently used as catalysts for this type of transformation. The present review describes the recent advances in the ruthenium-catalyzed chelation-assisted alkenylation at the C-H bond of aromatics, alkenes and heteroaromatics with alkenes via the deprotonation pathway. Several directing groups including 2-pyridyl, carbonyl, amidine, amide, amine, imidate, sulphonic acid, triazole, cyano, oxazolidinone and hydontoin are widely used in the reaction. The scope, limitation and mechanistic investigation of the alkenylation reactions are discussed elaborately. This feature article includes all the reported ruthenium-catalyzed alkenylation reactions via the deprotonation pathway until the end of March 2017.

  14. Synthesis and characterization of branched fcc/hcp ruthenium nanostructures and their catalytic activity in ammonia borane hydrolysis

    AlYami, Noktan

    2018-01-30

    Several systems have shown the ability to stabilize uncommon crystal structures during the synthesis of metallic nanoparticles. By tailoring the nanoparticle crystal structure, the physical and chemical properties of the particles can also be controlled. Herein, we first synthesized branched nanoparticles of mixed hcp/fcc ruthenium, which were formed using tungsten carbonyl [W(CO)6] as both a reducing agent and a source of carbon monoxide. The branched particles were formed from multiple particulates off a central core. High-resolution transmission electron microscopy (HRTEM) clearly showed that the branched structures consisted of aligned hcp crystal domains, a mixture of fcc and hcp crystal domains with several defects and misalignments, and particles that contained multiple cores and branches. Branched particles were also formed with molybdenum carbonyl [Mo(CO)6], and faceted particles of hcp and fcc particles were formed with Re2(CO)10 as a carbon monoxide source. Without metal carbonyls, small particles of spherical hcp ruthenium were produced, and their size could be controlled by the selection of the precursor. The ruthenium nanoparticles were tested for ammonia borane hydrolysis; the branched nanoparticles were more reactive for catalytic hydrogen evolution than the faceted hcp/fcc nanoparticles or the spherical hcp nanoparticles. This work showcases the potential of crystal phase engineering of transition metal nanoparticles by different carbon monoxide precursors for tailoring their catalytic reactivity.

  15. Synthesis and characterisation of ruthenium(III) complexes with benzimidazole derivatives

    Vyas, P.C.; Kaur, N.; Goel, A.K.; Vyas, S.

    1995-01-01

    Complexes of ruthenium trichloride with biologically important benzimidazole derivatives, viz., 2-(hydroxy methyl) benzimidazole, 2-(l-hydroxy ethyl) benzimidazole, 2-(mercapto methyl) benzimidazole, 2-(l-mercapto ethyl) benzimidazole, and 2,2'-bis-benzimidazole have been synthesized by reacting the above metal chloride and ligands respectively in 1:3 molar ratio. These complexes are characterised on the basis of elemental analysis, molar conductance data, room temperature, magnetic moment values, electronic spectral and IR spectral studies. (author). 17 refs., 2 tabs

  16. Aromatic oligoamides with a rare ortho-connectivity

    Hjelmgaard, T.; Nielsen, John

    2013-01-01

    studies indicated a more restricted rotation about the amide bonds in ortho-arylopeptoids, presumably due to a more congested backbone structure resulting from the ortho-connectivity pattern. Intriguingly, tert-butyl and phenyl side chains offer complete control over the amide conformations; whereas...... arylopeptoid residues with tert-butyl side chains adopt a 100 % cis amide conformation, the opposite 100 % trans amide conformation was observed in arylopeptoids with phenyl side chains. The tert-butyl moiety can furthermore serve as a protecting group during synthesis, which can later be removed to allow...

  17. Experiments on the behaviour of ruthenium in air ingress accidents

    Kaerkelae, T.; Backman, Ul; Auvinen, A.; Zilliacus, R.; Lipponen, M.; Kekki, T.; Tapper, U.; Jokiniemi, J.

    2007-03-01

    During routine nuclear reactor operation, ruthenium will accumulate in the fuel in relatively high concentrations. In a severe accident in a nuclear power plant it is possible that air gets into contact with the reactor core. In this case ruthenium may oxidise and form volatile ruthenium species, RuO3 and RuO4, which can be transported into the containment. In order to estimate the amount of gaseous ruthenium species, it is of interest to know, how they are formed and how they behave. In our experiments the formation and transport of volatile ruthenium oxides was studied by exposing RuO2 powder to diverse oxidising atmospheres at a relatively high temperature. Transport of gaseous RuO4 was further investigated by injecting it into the facility in similar conditions. Upon cooling of the gas flow RuO2 aerosol particles were formed in the system. They were removed from the gas stream with plane filters. Gaseous ruthenium species were trapped in 1M NaOH-water solution, which is capable of trapping RuO4 totally. Ruthenium in the solution was filtered for analysis. The determination of ruthenium both in aerosol and in liquid filters was made using instrumental neutron activation analysis (INAA). In order to close the mass balance and to achieve better time resolution seven experiment were carried out using radioactive tracer. In this report, the facility for the ruthenium behaviour study and results from experiments are presented. Preliminary conclusions from the experiments are reported as well. Final conclusions will be made after modelling of the facility is completed in a continuation work of this study. (au)

  18. Experiments on the behaviour of ruthenium in air ingress accidents

    Kaerkelae, T.; Backman, Ul; Auvinen, A.; Zilliacus, R.; Lipponen, M.; Kekki, T.; Tapper, U.; Jokiniemi, J. [Technical Research Centre of Finland VTT (Finland)

    2007-03-15

    During routine nuclear reactor operation, ruthenium will accumulate in the fuel in relatively high concentrations. In a severe accident in a nuclear power plant it is possible that air gets into contact with the reactor core. In this case ruthenium may oxidise and form volatile ruthenium species, RuO3 and RuO4, which can be transported into the containment. In order to estimate the amount of gaseous ruthenium species, it is of interest to know, how they are formed and how they behave. In our experiments the formation and transport of volatile ruthenium oxides was studied by exposing RuO2 powder to diverse oxidising atmospheres at a relatively high temperature. Transport of gaseous RuO4 was further investigated by injecting it into the facility in similar conditions. Upon cooling of the gas flow RuO2 aerosol particles were formed in the system. They were removed from the gas stream with plane filters. Gaseous ruthenium species were trapped in 1M NaOH-water solution, which is capable of trapping RuO4 totally. Ruthenium in the solution was filtered for analysis. The determination of ruthenium both in aerosol and in liquid filters was made using instrumental neutron activation analysis (INAA). In order to close the mass balance and to achieve better time resolution seven experiment were carried out using radioactive tracer. In this report, the facility for the ruthenium behaviour study and results from experiments are presented. Preliminary conclusions from the experiments are reported as well. Final conclusions will be made after modelling of the facility is completed in a continuation work of this study. (au)

  19. Characterization of ultrasonic spray pyrolysed ruthenium oxide thin films

    Patil, P.S.; Ennaoui, E.A.; Lokhande, C.D.; Mueller, M.; Giersig, M.; Diesner, K.; Tributsch, H. [Hahn-Meitner-Institut Berlin GmbH (Germany). Bereich Physikalische Chemie

    1997-11-21

    The ultrasonic spray pyrolysis (USP) technique was employed to deposit ruthenium oxide thin films. The films were prepared at 190 C substrate temperature and further annealed at 350 C for 30 min in air. The films were 0.22 {mu} thick and black grey in color. The structural, compositional and optical properties of ruthenium oxide thin films are reported. Contactless transient photoconductivity measurement was carried out to calculate the decay time of excess charge carriers in ruthenium oxide thin films. (orig.) 28 refs.

  20. Hazards and control of ruthenium in the nuclear fuel cycle

    Eichholz, G.G.

    1978-01-01

    A review is presented of present information on the possible hazards of radioruthenium in the nuclear fuel cycle and its behaviour in nuclear operations and in the environment. The subject is dealt with under the following headings: basic chemical and nuclear properties of ruthenium; chemistry (including the ruthenium-nitric acid system, electrochemistry, extraction processes); ruthenium toxicity; generation of radioruthenium (fallout sources, reactor sources, fuel reprocessing operations); waste treatment (cementation and bitumenization, calcining processes, vitrification); movement in the environment (movement of airborne effluents, liquid effluents and the freshwater environment, marine environment, bottom sediments, marine organisms, terrestrial environments, uptake in vegetation and animals); conclusion. (U.K.)

  1. Probes of the metal-to-ligand charge-transfer excited states in ruthenium-Am(m)ine-bipyridine complexes: the effects of NH/ND and CH/CD isotopic substitution on the 77 K luminescence.

    Chen, Yuan-Jang; Xie, Puhui; Endicott, John F; Odongo, Onduru S

    2006-06-29

    The effects of ligand perdeuteration on the metal-to-ligand charge-transfer (MLCT) excited-state emission properties at 77 K are described for several [Ru(L)(4)bpy](2+) complexes in which the emission process is nominally [uIII,bpy-] --> [RuII,bpy]. The perdeuteration of the 2,2'-bipyridine (bpy) ligand is found to increase the zero-point energy differences between the ground states and MLCT excited states by amounts that vary from 0 +/- 10 to 70 +/- 10 cm(-1) depending on the ligands L. This indicates that there are some vibrational modes with smaller force constants in the excited states than in the ground states for most of these complexes. These blue shifts increase approximately as the energy difference between the excited and ground states decreases, but they are otherwise not strongly correlated with the number of bipyridine ligands in the complex. Careful comparisons of the [Ru(L)(4)(d(8)-bpy)](2+) and [Ru(L)(4)(h(8)-bpy](2+) emission spectra are used to resolve the very weak vibronic contributions of the C-H stretching modes as the composite contributions of the corresponding vibrational reorganizational energies. The largest of these, 25 +/- 10 cm(-1), is found for the complexes with L = py or bpy/2 and smaller when L = NH(3). Perdeuteration of the am(m)ine ligands (NH(3), en, or [14]aneN(4)) has no significant effect on the zero-point energy difference, and the contributions of the NH stretching vibrational modes to the emission band shape are too weak to resolve. Ligand perdeuteration does increase the excited-state lifetimes by a factor that is roughly proportional to the excited-state-ground-state energy difference, even though the CH and NH vibrational reorganizational energies are too small for nuclear tunneling involving these modes to dominate the relaxation process. It is proposed that metal-ligand skeletal vibrational modes and configurational mixing between metal-centered, bpy-ligand-centered, and MLCT excited states are important in

  2. Ruthenium sulfoxides structure and reactivity with nitrogen heterocyclic bases

    Oliveira, Denise de.

    1990-01-01

    Ruthenium (II) sulfoxides are compounds of great interest in oxidative catalysis and in chemotherapy. In order to contribute for the understanding of the chemistry and electronic structure of this class of compounds, it has been studied a series of [Ru Cl 2 (S-DMSO) 2 L x ] complexes, where x = 1 (polymeric compounds) or 2 (monomers) and L N-heterocyclic ligands (pyridine, pyrazine and imidazole derivatives). The nature of N-heterocyclic ligand and their coordination are of great relevance to the stability, spectroscopic and electrochemical characteristics of the complexes. The trans-interactions are extremely important in this series, influencing the strength of the Ru(II)-> S-DMSO and Ru(II)-> L π-back donation. The DMSO and L ligands are π-acceptors. The metal-> ligand π-back donation is strengthened when the ligand is trans to chloride, which is π-donor, due to trans-cooperative interactions of the type: π-donor -> Ru(II) π-acceptor. Another interesting aspect in the series of [Ru Cl 2 (S-DMSO) 2 L 2 ] complexes is the occurrence of dissociative equilibria in the solution, due to the existence of three types of ligands. It was observed that the trans-N isomer of 2,6-dimethyl pyrazine derivative undergoes thermal substitution, with preferential liabilization of the N-heterocyclic ligand. Chloride ion is the most inert ligand in this complex. (author). 145 refs., 76 figs., 21 tabs

  3. Scaling-resistance of ruthenium- and ruthenium phosphides powders in argon and air

    Chernogorebko, V.B.; Semenov-Kobzar', A.A.; Kulik, L.Ya.

    1976-01-01

    The thermal stability of ruthenium phosphides in air diminishes as the content of phosphorus in the compound increases. The temperatures at which active oxidation of the powders starts are as follows: Ru-600, Ru 2 P-590, RuP-390, and RuP 2 -270 0 C. The oxidation of phosphorus in the phosphides proceeds in steps. The atoms of phosphorus which are most accessible to oxygen are first oxidated. Phosphorus atoms in the octahedral spaces are oxidated less easily, simultaneously with the oxidation of the ruthenium atoms. When heated in argon, Ru 2 P and RuP fuse congruently at 1,500 and 1,555 0 C respectively, while RuP 2 dissociates at 950 0 C. (author)

  4. Separation of platinum metals by theirs extraction as sulfides

    Pilipenko, A.T.; Ryabushko, O.P.; Ty Van Mak

    1978-01-01

    Separation of platinum metals by means of their sediment in the form of sulfides with subsequent extraction is studied. The optimum conditions of metal sulfide extraction are determined, the metal output dependence from acidness and aqueous phase composition and also the organic solvent nature are investigated. Ruthenium concentration was determined photometrically. Ruthenium sulfide is extracted by butyl spirit from 1-4 normal hydrochloric acid. The maximum extraction grade of 63% is reached in 3.2-normal acid. When the mixture of acetic and hydrochloric acids (2:1) is used for decomposition of ruthenium tiosalts, the grade of ruthenium extraction by amyl spirit or the mixture of anyl and butyl spirits (1:1) constitutes 100%

  5. Ortho lithiation-in situ borylation of substituted morpholine benzamides

    Cederbalk, Anna; Lysén, Morten; Kehler, Jan

    2017-01-01

    Morpholine amides are cheap and safe alternative to Weinreb amides as acylating agents of organometallic species. Herein, the in-situ lithiation/borylation of 18 ortho- meta- and para-substituted morpholine benzamides has been investigated. 10 of the 18 substrates provided the desired boronic est...

  6. Ruthenium(II) tris(2,2'-bipyridine) chelate as a chemiluminophore in extrinsic lyoluminescences of aluminium and magnesium in aqueous solution

    Jiang Qinghong; Kotiranta, Miia; Langel, Kaarina; Suomi, Johanna; Hakansson, Markus; Spehar, Anna-Maria; Ala-Kleme, Timo; Eskola, Jarkko; Kulmala, Sakari

    2005-01-01

    Ruthenium(II) tris(2,2'-bipyridine) chelate shows chemiluminescence (CL) both during dissolution of metallic aluminium in alkaline conditions, and during dissolution of magnesium metal in acidic conditions. The presence of peroxodisulfate ions strongly enhances the CL. Magnesium system provides considerably better detectability of the present chelate giving linear calibration plot spanning over many orders of magnitude of concentration down to subnanomolar concentration levels. The possible primary species generated and luminescence mechanisms are shortly discussed

  7. Ruthenium, osmium and rhodium complexes of polypyridyl ligands ...

    Unknown

    Discipline of Silicates and Catalysis, Central Salt and Marine Chemicals ... However, synthetic methods have also been developed to prepare complexes with ... 3.2 Synthesis and characterisation of ruthenium(II) and osmium(II) complexes18, ...

  8. Synthesis of ruthenium (III) complexes with benzimidazole derivatives

    Vyas, P.C.; Chahar, Yogesh K.; Garg, Yajula; Seth, Gita

    2003-01-01

    Complexes of ruthenium with biologically important benzimidazole derivatives, viz. 2-(2'-hydroxyphenyl) benzimidazole (HOPBI), 2-2'- mercaptophenyl) benzimidazole (HSPBI), 2- (2'-hydroxynaphthyl) benzimidazole (HONBI) have been synthesized and characterized. (author)

  9. Supercapacitive performance of hydrous ruthenium oxide (RuO2 ...

    gel method have been employed to prepare ruthenium oxide thin films. Recently ... the potentiostat (263A EG&G, Princeton Applied Research. Potentiostat). .... is a mixed conductor that conducts protons and electrons in acidic solution (as ...

  10. Separation through liquid-liquid extraction and spectrophotometric determination of U(VI) with the ortho-aminophenol reagent

    Marian Raileanu

    2012-01-01

    The extractive properties of the ortho-aminophenol reagent upon U(VI) were investigated in two solvents: 4-chlor-acetophenone and acetylacetone, in a water-organic solvent system. The method here proposed is based on the complexation reaction of the uranyl ion, UO 2 2+ , with ortho-aminophenol dissolved in 4-chlor-acetophenone, at room temperature, over a pH interval 4-6, followed by spectro-photometry of the organic phase, involving measuring of absorbancy at 569.6 nm. The Beer law is valid over the 1-12, μg U(VI)/mL concentration interval, with molar absorptivity ε max 4.3 x 10 5 mol -1 cm 2 and Sandell sensitivity = 0.0526 μg cm -2 . The structure, stability and solubility of the formed complex was studied by UV-VIS and IR spectrometry, diffractometry and scanning electron microscopy. The mixed complex formed between the uranyl ion and the ortho-aminophenol dissolved in 4-chlor-acetophenone, [UO 2 .(L) 2 .(S) 4 ], is characterized by the following parameters: metal/ligand combination ratio: M/L = 1/2, stability constant β = 2.06 x 10 6 , distribution coefficient D = 66.56 (V org = V aq ), percentage extraction E% = 98.52, and recovery factor, R%, ranging between 99.48 and 99.85%. (author)

  11. Rare earth-ruthenium-magnesium intermetallics

    Stein, Sebastian; Kersting, Marcel; Heletta, Lukas; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie

    2017-07-01

    Eight new intermetallic rare earth-ruthenium-magnesium compounds have been synthesized from the elements in sealed niobium ampoules using different annealing sequences in muffle furnaces. The compounds have been characterized by powder and single crystal X-ray diffraction. Sm{sub 9.2}Ru{sub 6}Mg{sub 17.8} (a=939.6(2), c=1779(1) pm), Gd{sub 11}Ru{sub 6}Mg{sub 16} (a=951.9(2), c=1756.8(8) pm), and Tb{sub 10.5}Ru{sub 6}Mg{sub 16.5} (a=942.5(1), c=1758.3(4) pm) crystallize with the tetragonal Nd{sub 9.34}Ru{sub 6}Mg{sub 17.66} type structure, space group I4/mmm. This structure exhibits a complex condensation pattern of square-prisms and square-antiprisms around the magnesium and ruthenium atoms, respectively. Y{sub 2}RuMg{sub 2} (a=344.0(1), c=2019(1) pm) and Tb{sub 2}RuMg{sub 2} (a=341.43(6), c=2054.2(7) pm) adopt the Er{sub 2}RuMg{sub 2} structure and Tm{sub 3}Ru{sub 2}Mg (a=337.72(9), c=1129.8(4) pm) is isotypic with Sc{sub 3}Ru{sub 2}Mg. Tm{sub 3}Ru{sub 2}Mg{sub 2} (a=337.35(9), c=2671(1) pm) and Lu{sub 3}Ru{sub 2}Mg{sub 2} (a=335.83(5), c=2652.2(5) pm) are the first ternary ordered variants of the Ti{sub 3}Cu{sub 4} type, space group I4/mmm. These five compounds belong to a large family of intermetallics which are completely ordered superstructures of the bcc subcell. The group-subgroup scheme for Lu{sub 3}Ru{sub 2}Mg{sub 2} is presented. The common structural motif of all three structure types are ruthenium-centered rare earth cubes reminicent of the CsCl type. Magnetic susceptibility measurements of Y{sub 2}RuMg{sub 2} and Lu{sub 3}Ru{sub 2}Mg{sub 2} samples revealed Pauli paramagnetism of the conduction electrons.

  12. Effects of a mixture of non-ortho- and mono-ortho-polychlorinated biphenyls on reproduction in Fundulus heteroclitus (Linnaeus)

    Black, D.E.; Gutjahr-Gobell, R.; Pruell, R.J.; Bergen, B. [Environmental Protection Agency, Narragansett, RI (United States); McElroy, A.E. [State Univ. of New York, Stony Brook, NY (United States). Marine Sciences Research Center

    1998-07-01

    To assess the effects of polychlorinated biphenyls (PCBs) on reproduction, female Fundulus heteroclitus were exposed to a mixture of non-ortho- and mono-ortho-PCBs, mimicking the mixture found in fish collected from New Bedford Harbor, Massachusetts, USA, a PCB-contaminated estuary. Exposure was by intraperitoneal injection of the mixture dissolved in corn oil. Doses of 0.76, 3.8, and 19 {micro}g PCB mixture per gram of wet weight produced liver concentrations of 2.99, 12.2, and 32.8 {micro}g non-ortho- and mono-ortho-PCBs per gram of dry liver, with dioxin toxic equivalency concentrations (TEQs) of 0.0963, 0.409, and 0.720 ng/g, respectively. Female mortality was 58%, and egg production was reduced by 77% at the highest dose, compared to controls. Food consumption declined with increasing PCB concentration, suggesting that PCBs act indirectly to reduce fecundity through an energetic effect. Pituitary gonadotropin content appeared to be suppressed at the highest dose, but the ability of ovarian follicles to produce estradiol and testosterone in vitro was not impaired. Significant residue-effects linkages were found, with TEQ emerging as a potential indicator of adverse effects. Mortality was directly related, and egg production was inversely related to log{sub 10}TEQ. Multiple regression analysis indicated that egg production was directly related to pituitary gonadotropin content and food consumption.

  13. PCDFs, PCDDs, non-ortho PCBs, and mono-ortho PCBs in northern fulmars from the Faroe Islands

    Ericson, I.M.; Hagberg, J.; Bavel van, B.; Lindstrom, G. [Orebro Univ., Orebro (Sweden). MTM Research Centre; Dam, M. [Food and Environment Agency, Torshavn, Faroe Islands (Denmark); Jensen, J.K.; Danielsen, J. [Faroese Museum of Natural History, Faroe Islands (Denmark)

    2005-07-01

    Eggs and tissues of Northern Fulmars have been used to monitor the contamination of the Canadian Arctic marine environment since 1975. Dioxin levels for northern fulmars in the Arctic are among the highest reported for birds. This study reported the results of analyses of dioxins (PCDDs) and non- and mono-ortho polychlorinated biphenyls (PCBs) in liver tissue from juvenile northern fulmars from the Faeroe Islands in 2003. The samples were collected during a traditional hunt and ground with anhydrous sodium sulfate. Sample extraction was performed using supercritical fluid extraction coupled to a solid phase liquid chromatography trap (SFE-LC). Target compounds were collected on a solid phase trap containing AX-21 carbon on ODS silica and eluted with 6 ml n-hexane/dichloromethane for non-planar compounds and xylene for planar compounds. PCDD and planar PCB analysis was performed on an a high resolution gas chromatography (GC) mass spectrometer (MS) operating at 10,000 resolution using EI ionization at 35 eV. Concentrations of PCDFs, PCDDs, non, and mono-ortho PCBs were detected in all samples. High levels of mono-ortho PCBs were detected, as well as non-ortho PCBs, PCDFs, and PCDDs. It was concluded that levels and congener patterns in fulmars from the Faroe Islands and the Canadian Arctic were comparable. However, slightly higher levels were detected in the Faeroe Islands samples. 9 refs., 1 tab., 2 figs.

  14. Ruthenium nanoparticles decorated curl-like porous carbons for high performance supercapacitors

    Lou, Bih-Show; Veerakumar, Pitchaimani; Chen, Shen-Ming; Veeramani, Vediyappan; Madhu, Rajesh; Liu, Shang-Bin

    2016-01-01

    The synthesis of highly dispersed and stable ruthenium nanoparticles (RuNPs; ca. 2-3 nm) on porous activated carbons derived from Moringa Oleifera fruit shells (MOC) is reported and were exploited for supercapacitor applications. The Ru/MOC composites so fabricated using the biowaste carbon source and ruthenium acetylacetonate as the co-feeding metal precursors were activated at elevated temperatures (600-900 oC) in the presence of ZnCl2 as the pore generating and chemical activating agent. The as-prepared MOC carbonized at 900 oC was found to possess a high specific surface area (2522 m2 g-1) and co-existing micro- and mesoporosities. Upon incorporating RuNPs, the Ru/MOC nanocomposites loaded with modest amount of metallic Ru (1.0-1.5 wt%) exhibit remarkable electrochemical and capacitive properties, achiving a maximum capacitance of 291 F g-1 at a current density of 1 A g-1 in 1.0 M H2SO4 electrolyte. These highly stable and durable Ru/MOC electrodes, which can be facily fabricated by the eco-friendly and cost-effective route, should have great potentials for practical applications in energy storage, biosensing, and catalysis.

  15. Determination of microgramme amounts of osmium and ruthenium based on inhibition of the iodine-azide reaction by their complexes with 6-mercaptopurine

    Matusiewicz, H.; Kurzawa, Z.

    1976-01-01

    A new kinetic method of the determination of microamounts of osmium and ruthenium has been developed. The reaction between sodum azide and iodine induced by 6-mercaptopurine (6-MP) was used for this purpose. Under suitable experimental conditions the induction coefficient of 6-MP amounts to 1750+-40. The formed complexes of the metals are stable in the medium containing an excess of azide ions and do not induce the iodine-azide reaction. The method consists in the determination of the 6-MP not bound to the metal. The amount of osmium or ruthenium is then determined from linear relations. Before the determination osmium and ruthenium must be separated from other cations and from each other by distillation as volatile tetroxides. The iodine-azide method is simple, sensitive and does not require any apparatus. The range of the determination is 0.1-5.0 μg in 5 cm 3 of the solution of Os(8) and 0.5-5.0 μg for Ru(8). The error of the determination is +-6.4% and +- 6.1% for osmium and ruthenium, respectively. The time of the determination is 30 minutes not taking into account 2-hour waiting time necessary for the formation of the complexes. (author)

  16. Studying the effect of Ruthenium on High Temperature Mechanical Properties of Nickel Based Superalloys and Determining the Universal Behavior of Ruthenium at Atomic Scale with respect to alloying elements, Stress and Temperature

    Sriswaroop Dasari

    2016-10-01

    Full Text Available Any property of a material is a function of its microstructure and microstructure is a function of material composition. So, to maximize the desired properties of a material, one has to understand the evolution of microstructure which in turn is nothing but the reflection of the role of alloying elements. Research has not been done to understand the universal behavior of a certain base/alloying element. Let’s take the example of Cl- ion in HCl, we all know that in general, chloride ion can only be replaced by Fluoride or oxygen ion and that no other ion can replace it. But when you consider a metal like Ni, Co, Cr, Fe etc. there is no establishment that it behaves only in a certain way. Though I concord to the fact that discovery of universal behavior of Ni is lot complex than chloride ion, I think that future research should be focused in this direction also. Superalloys are the candidate materials required to improve thermal efficiency of a gas turbine by allowing higher turbine inlet gas temperatures. Gas turbines are the heart of local power systems, next generation jet engines and high performance space rockets. Recent research in superalloys showed that addition of some alloying elements in minor quantities can result in drastic change in properties. Such an alloying element is Ruthenium (Ru. Addition of Ruthenium to superalloys has shown improvement in mechanical properties by an order of magnitude. However reasons for such improvement are not known yet. Hence, there is a need to identify its role and discover the universal behavior of ruthenium to utilize it efficiently. In this proposal, we study materials with different compositions that are derived based on one ruthenium containing superalloy, and different thermomechanical history. Based on the evolution of microstructures and results of mechanical testing, we plan to determine the exact role of Ruthenium and prediction of its behavior with respect to other elements in the material

  17. Ruthenium Sensitizers and Their Applications in Dye-Sensitized Solar Cells

    Yuancheng Qin

    2012-01-01

    Full Text Available Dye-sensitized solar cells (DSSCs have attracted considerable attention in recent years due to the possibility of low-cost conversion of photovoltaic energy. The DSSCs-based ruthenium complexes as sensitizers show high efficiency and excellent stability, implying potential practical applications. This review focuses on recent advances in design and preparation of efficient ruthenium sensitizers and their applications in DSSCs, including thiocyanate ruthenium sensitizers and thiocyanate-free ruthenium sensitizers.

  18. Kinetics and Photochemistry of Ruthenium Bisbipyridine Diacetonitrile Complexes: An Interdisciplinary Inorganic and Physical Chemistry Laboratory Exercise

    Rapp, Teresa L.; Phillips, Susan R.; Dmochowski, Ivan J.

    2016-01-01

    The study of ruthenium polypyridyl complexes can be widely applied across disciplines in the undergraduate curriculum. Ruthenium photochemistry has advanced many fields including dye-sensitized solar cells, photoredox catalysis, lightdriven water oxidation, and biological electron transfer. Equally promising are ruthenium polypyridyl complexes…

  19. Flow carbonylation of sterically hindered ortho-substituted iodoarenes

    Carl J. Mallia

    2016-07-01

    Full Text Available The flow synthesis of ortho-substituted carboxylic acids, using carbon monoxide gas, has been studied for a number of substrates. The optimised conditions make use of a simple catalyst system compromising of triphenylphosphine as the ligand and palladium acetate as the pre-catalyst. Carbon monoxide was introduced via a reverse “tube-in-tube” flow reactor at elevated pressures to give yields of carboxylated products that are much higher than those obtained under normal batch conditions.

  20. Experimental study of para- and ortho-H3+ recombination

    Plasil, R; Varju, J; Hejduk, M; Dohnal, P; KotrIk, T; Glosik, J

    2011-01-01

    Recombination of H 3 + with electrons is a key process for many plasmatic environments. Recent experiments on storage ring devices used ion sources producing H 3 + with enhanced populations of H 3 + ions in the para nuclear spin configuration to shed light on the theoretically predicted faster recombination of para states. Although increased recombination rates were observed, no in situ characterization of recombining ions was performed. We present a state selective recombination study of para- and ortho-H 3 + ions with electrons at 77 K in afterglow plasma in a He/Ar/H 2 gas-mixture. Both spin configurations of H 3 + have been observed in situ with a near infrared cavity ring down spectrometer (NIR-CRDS) using the two lowest energy levels of H 3 + . Using hydrogen with an enhanced population of H 2 molecules in para states allowed us to influence the [para-H 3 + ]/[ortho-H 3 + ] ratio in the discharge and in the afterglow. We observed an increase in the measured effective recombination rate coefficients with the increase of the fraction of para-H 3 + . Measurements with different fractions of para-H 3 + at otherwise identical conditions allowed us to determine the binary recombination rate coefficients for pure para-H 3 + p α bin (77 K) = (2.0±0.4)x10 -7 cm 3 s -1 and pure ortho-H 3 + o α bin (77 K) = (4±3)x10 -8 cm 3 s -1 .

  1. Biological and therapeutic effects of ortho-silicic acid and some ortho-silicic acid-releasing compounds: New perspectives for therapy

    Jurkić Lela Munjas

    2013-01-01

    Full Text Available Abstract Silicon (Si is the most abundant element present in the Earth's crust besides oxygen. However, the exact biological roles of silicon remain unknown. Moreover, the ortho-silicic acid (H4SiO4, as a major form of bioavailable silicon for both humans and animals, has not been given adequate attention so far. Silicon has already been associated with bone mineralization, collagen synthesis, skin, hair and nails health atherosclerosis, Alzheimer disease, immune system enhancement, and with some other disorders or pharmacological effects. Beside the ortho-silicic acid and its stabilized formulations such as choline chloride-stabilized ortho-silicic acid and sodium or potassium silicates (e.g. M2SiO3; M= Na,K, the most important sources that release ortho-silicic acid as a bioavailable form of silicon are: colloidal silicic acid (hydrated silica gel, silica gel (amorphous silicon dioxide, and zeolites. Although all these compounds are characterized by substantial water insolubility, they release small, but significant, equilibrium concentration of ortho-silicic acid (H4SiO4 in contact with water and physiological fluids. Even though certain pharmacological effects of these compounds might be attributed to specific structural characteristics that result in profound adsorption and absorption properties, they all exhibit similar pharmacological profiles readily comparable to ortho-silicic acid effects. The most unusual ortho-silicic acid-releasing agents are certain types of zeolites, a class of aluminosilicates with well described ion(cation-exchange properties. Numerous biological activities of some types of zeolites documented so far might probably be attributable to the ortho-silicic acid-releasing property. In this review, we therefore discuss biological and potential therapeutic effects of ortho-silicic acid and ortho-silicic acid -releasing silicon compounds as its major natural sources.

  2. Nitrile-functionalized ruthenium nanoparticles: charge delocalization through Ru − N ≡ C interface

    Zhang, Fengqi; Huang, Lin; Zou, Jiasui; Yan, Jinwu; Zhu, Jiaying; Kang, Xiongwu; Chen, Shaowei

    2017-01-01

    Ruthenium nanoparticles (2.06 ± 0.46 nm in diameter) were stabilized by the self-assembly of nitrile molecules onto the ruthenium colloid surface by virtue of the formation of Ru−N≡C interfacial bonding linkages. Thermogravimetric analysis showed that there were about 63 nitrile ligands per nanoparticle, corresponding to an average molecular footprint of 22.4 Å 2 . Proton nuclear magnetic resonance (NMR) studies suggested an end-on configuration of the nitrile moiety on the metal core surface. Meanwhile, infrared measurements showed that the C≡N stretch red-shifted from 2246 to 1944 cm −1 upon adsorption on the nanoparticle surfaces, as confirmed by 15 N isotopic labeling. This apparent red-shift suggests extensive intraparticle charge delocalization, which was further manifested by photoluminescence measurements of 1-cyanopyrene-functionalized ruthenium nanoparticles that exhibited a red shift of 40 nm of the emission maximum, in comparison to that of free monomers. The results further highlight the significance of metal−organic contacts in the manipulation of the dynamics of intraparticle charge transfer and the nanoparticle optical and electronic properties.

  3. Nitrile-functionalized ruthenium nanoparticles: charge delocalization through Ru − N ≡ C interface

    Zhang, Fengqi; Huang, Lin; Zou, Jiasui [South China University of Technology, New Energy Research Institute, School of Environment and Energy, Guangzhou Higher Education Mega Centre (China); Yan, Jinwu; Zhu, Jiaying [South China University of Technology, School of Bioscience and Bioengineering, Guangzhou Higher Education Mega Centre (China); Kang, Xiongwu, E-mail: esxkang@scut.edu.cn; Chen, Shaowei, E-mail: shaowei@ucsc.edu [South China University of Technology, New Energy Research Institute, School of Environment and Energy, Guangzhou Higher Education Mega Centre (China)

    2017-03-15

    Ruthenium nanoparticles (2.06 ± 0.46 nm in diameter) were stabilized by the self-assembly of nitrile molecules onto the ruthenium colloid surface by virtue of the formation of Ru−N≡C interfacial bonding linkages. Thermogravimetric analysis showed that there were about 63 nitrile ligands per nanoparticle, corresponding to an average molecular footprint of 22.4 Å{sup 2}. Proton nuclear magnetic resonance (NMR) studies suggested an end-on configuration of the nitrile moiety on the metal core surface. Meanwhile, infrared measurements showed that the C≡N stretch red-shifted from 2246 to 1944 cm{sup −1} upon adsorption on the nanoparticle surfaces, as confirmed by {sup 15}N isotopic labeling. This apparent red-shift suggests extensive intraparticle charge delocalization, which was further manifested by photoluminescence measurements of 1-cyanopyrene-functionalized ruthenium nanoparticles that exhibited a red shift of 40 nm of the emission maximum, in comparison to that of free monomers. The results further highlight the significance of metal−organic contacts in the manipulation of the dynamics of intraparticle charge transfer and the nanoparticle optical and electronic properties.

  4. Dealloyed Ruthenium Film Catalysts for Hydrogen Generation from Chemical Hydrides

    Ramis B. Serin

    2017-07-01

    Full Text Available Thin-film ruthenium (Ru and copper (Cu binary alloys have been prepared on a Teflon™ backing layer by cosputtering of the precious and nonprecious metals, respectively. Alloys were then selectively dealloyed by sulfuric acid as an etchant, and their hydrogen generation catalysts performances were evaluated. Sputtering time and power of Cu atoms have been varied in order to tailor the hydrogen generation performances. Similarly, dealloying time and the sulfuric acid concentration have also been altered to tune the morphologies of the resulted films. A maximum hydrogen generation rate of 35 mL min−1 was achieved when Cu sputtering power and time were 200 W and 60 min and while acid concentration and dealloying time were 18 M and 90 min, respectively. It has also been demonstrated that the Ru content in the alloy after dealloying gradually increased with the increasing the sputtering power of Cu. After 90 min dealloying, the Ru to Cu ratio increased to about 190 times that of bare alloy. This is the key issue for observing higher catalytic activity. Interestingly, we have also presented template-free nanoforest-like structure formation within the context of one-step alloying and dealloying used in this study. Last but not least, the long-time hydrogen generation performances of the catalysts system have also been evaluated along 3600 min. During the first 600 min, the catalytic activity was quite stable, while about 24% of the catalytic activity decayed after 3000 min, which still makes these systems available for the development of robust catalyst systems in the area of hydrogen generation.

  5. Nanoengineering of Ruthenium and Platinum-based Nanocatalysts by Continuous-Flow Chemistry for Renewable Energy Applications

    AlYami, Noktan Mohammed

    2017-04-15

    This thesis presents an integrated study of nanocatalysts for heterogenous catalytic and electrochemical processes using pure ruthenium (Ru) with mixed-phase and platinum-based nanomaterials synthesized by continuous-flow chemistry. There are three major challenges to the application of nanomaterials in heterogenous catalytic reactions and electrocatalytic processes in acidic solution. These challenges are the following: (i) controlling the size, shape and crystallography of nanoparticles to give the best catalytic properties, (ii) scaling these nanoparticles up to a commercial quantity (kg per day) and (iii) making stable nanoparticles that can be used catalytically without degrading in acidic electrolytes. Some crucial limitations of these nanostructured materials in energy conversion and storage applications were overcome by continuous-flow chemistry. By using a continuous-flow reactor, the creation of scalable nanoparticle systems was achieved and their functionality was modified to control the nanoparticles’ physical and chemical characteristics. The nanoparticles were also tested for long-term stability, to make sure these nanoparticles were feasible under realistic working conditions. These nanoparticles are (1) shape- and crystallography-controlled ruthenium (Ru) nanoparticles, (2) size-controlled platinum-metal (Pt-M= nickel (Ni) & copper (Cu)) nanooctahedra (while maintaining morphology) and (3) core-shell platinum@ruthenium (Pt@Ru) nanoparticles where an ultrathin ruthenium shell was templated onto the platinum core. Thus, a complete experimental validation of the formation of a scalable amount of these nanoparticles and their catalytic activity and stability towards the oxygen evolution reaction (OER) in acid medium, hydrolysis of ammonia borane (AB) along with plausible explanations were provided.

  6. Trends in oxygen reduction and methanol activation on transition metal chalcogenides

    Tritsaris, Georgios; Nørskov, Jens Kehlet; Rossmeisl, Jan

    2011-01-01

    We use density functional theory calculations to study the oxygen reduction reaction and methanol activation on selenium and sulfur-containing transition metal surfaces. With ruthenium selenium as a starting point, we study the effect of the chalcogen on the activity, selectivity and stability...... of the catalyst. Ruthenium surfaces with moderate content of selenium are calculated active for the oxygen reduction reaction, and insensitive to methanol. A significant upper limit for the activity of transition metal chalcogenides is estimated....

  7. Synthesis and electrochemistry of tri- and tetranuclear polypyridine derivations of ruthenium

    Francis, A.M.A.

    1990-01-01

    The synthesis of clusters of ruthenium is the focus of this work. The electrochemistry of metal cluster derivatives of ruthenium, iron and osmium are reviewed. The ability of these compounds to undergo more than one electron transfer reaction and to act as electron reservoirs is evident. The synthesis and characterisation of a range of polypyridine derivatives of [Ru 3 (CO) 12 ]; [Ru 3 (CO) 10 (napy)]; [Ru 3 (CO) 10 (bipy)]; [Ru 4 H 4 (CO) 12 ]; [Ru 4 H 4 (CO) 8 (bipy) 2 ] and [Ru 4 H 4 (CO) 10 (bipy)] were dealt with. The crystal structures of [Ru 3 (CO) 10 (napy)] and [Ru 4 H 4 (CO) 10 (bipy)] were also determined. The six compounds were fully investigated and a mechanism for their electrochemical reduction was postulated based on their observed experimental data, and that of the relevant compounds. The techniques used are also described and a brief introduction to the actual theory and practise of these techniques is discussed. 132 refs., 33 figs., 22 tabs

  8. The effect of NO2 on spectroscopic and structural properties of evaporated ruthenium phthalocyanine dimer

    Alagna, Lucilla; Capobianchi, Aldo; Paoletti, Anna Maria; Pennesi, Giovanna; Rossi, Gentilina; Casaletto, Maria Pia; Generosi, Amanda; Paci, Barbara; Albertini, Valerio Rossi

    2006-01-01

    The chemical interaction between NO 2 gas and dimeric ruthenium phthalocyanine (RuPc) 2 (Pc = phthalocyanine ligand) films has been investigated by different techniques: UV-Visible spectroscopy, X-ray Photoelectron Spectroscopy (XPS) and Extended X-ray Absorption Fine Structure (EXAFS). The optical spectra in the Q band region (700-500 nm) registered 'in situ' enabled to follow the evolution of the process in real time indicating that a two steps reaction, showing two clear isosbestic points, occurs. The first phase was essentially characterised by: (a) the rapid disappearance of the 608 and 420 nm shoulders; (b) the intensity decrease of the main absorption peak and (c) the appearance of a new adsorption band centred around 510 nm. In the second step the remarkable feature is a further lowering of the main peak with the simultaneous decrease of the new 510 nm absorption. These spectral changes suggested that a chemical reaction occurred between NO 2 and ruthenium phthalocyanine with the formation of a radical species due to the macrocycle oxidation. The kinetics indicates that the adsorption of gas by the evaporated (RuPc) 2 film is a complex process involving more than one independent mechanism. XPS and EXAFS spectra collected before and after gas exposure showed that the central metals (Ru) were also involved in the oxidation process. The reversibility of the process has been also tested by treating the films at different temperatures, the original optical spectrum being not completely recovered

  9. Behavior of ruthenium, cesium and antimony in high temperature processes for waste conditioning

    Klein, M.; Weyers, C.; Goossens, W.R.A.

    1985-01-01

    The fission products and the actinides of high level radioactive liquid wastes can be immobilized by incorporation into a glass matrix prior to disposal. The behaviour of so-called semi-volatile products during the vitrification process has been studied by the C.E.N./S.C.K. in Mol since 1979 in the framework of a contract with DWK of Germany in support to the HAW technological program PAMELA. The experiments were performed on laboratory and semi-pilot scale using simulated LEWC solutions tagged with radioisotopes of three suspected volatile fission products, namely ruthenium, cesium and antimony. The releases of these semi-volatile compounds to the off-gases have been investigated for a liquid fed melter as a function of the operational conditions. The study of a wet purification system, comprising in series of a dust scrubber, a condensor, an ejector venturi and an NOsub(x) column, has shown that cesium appears to be the reference isotope for the volatile elements released from the melter. Ruthenium seems not to be a problem from the point of view of gas purification although local radiation problems caused by deposits on metal surfaces cannot be excluded. (Auth.)

  10. Ortho-H2 and the age of prestellar cores

    Pagani, L.; Lesaffre, P.; Jorfi, M.; Honvault, P.; González-Lezana, T.; Faure, A.

    2013-03-01

    Prestellar cores form from the contraction of cold gas and dust material in dark clouds before they collapse to form protostars. Several concurrent theories exist to describe this contraction but they are currently difficult to distinguish. One major difference is the timescale involved in forming the prestellar cores: some theories advocate nearly free-fall speed via, e.g., rapid turbulence decay, while others can accommodate much longer periods to let the gas accumulate via, e.g., ambipolar diffusion. To tell the difference between these theories, measuring the age of prestellar cores could greatly help. However, no reliable clock currently exists. We present a simple chemical clock based on the regulation of the deuteration by the abundance of ortho-H2 that slowly decays away from the ortho-para statistical ratio of 3 down to or less than 0.001. We use a chemical network fully coupled to a hydrodynamical model that follows the contraction of a cloud, starting from uniform density, and reaches a density profile typical of a prestellar core. We compute the N2D+/N2H+ ratio along the density profile. The disappearance of ortho-H2 is tied to the duration of the contraction and the N2D+/N2H+ ratio increases in the wake of the ortho-H2 abundance decrease. By adjusting the time of contraction, we obtain different deuteration profiles that we can compare to the observations. Our model can test fast contractions (from 104 to 106 cm-3 in ~0.5 My) and slow contractions (from 104 to 106 cm-3 in ~5 My). We have tested the sensitivity of the models to various initial conditions. The slow-contraction deuteration profile is approximately insensitive to these variations, while the fast-contraction deuteration profile shows significant variations. We found that, in all cases, the deuteration profile remains clearly distinguishable whether it comes from the fast collapse or the slow collapse. We also study the para-D2H+/ortho-H2D+ ratio and find that its variation is not monotonic

  11. Reactions of dihydridotetrakis(triphenylphosphine)ruthenium(II) with olefins and isolation of new ruthenium-olefin complexes

    Komiya, Sanshiro; Yamamoto, Akio

    1976-01-01

    Dihydridotetrakis(triphenylphosphine)ruthenium (II), RuH 2 (PPh 3 ) 4 , reacts with olefins (ethylene, propylene, stylene and butadiene) to give olefin-coordinated complexes of the type, Ru(olefin)(PPh 3 ) 3 and equimolar amounts of their hydrogenation products per mol of the dihydride complex. The olefin coordinated with ruthenium can be exchanged with other olefins. Olefin-coordinated complexes easily react with molecular hydrogen to afford tetrahydridotris(triphenylphosphine)ruthenium, RuH 4 (PPh 3 ) 3 , releasing alkane at room temperature, Under hydrogen atmosphere catalytic hydrogenation of the olefins smoothly takes place with RuH 2 (PPh 3 ) 4 . (Ethylene)tris(triphenylphosphine)ruthenium(0) reacts with methyl iodide to give propylene and a trace of butadiene along with methane, ethylene, and small amounts of ethane and butenes. The formation of propylene suggests that oxidative addition involving cleavage of the C-H bond of ethylene to ruthenium giving a hydridovinyl complex may be taking place. Reactions of Ru(C 2 H 4 )(PPh 3 ) 3 with methyl-d 3 iodide and ethyl iodide, and of Ru(C 3 H 6 )(PPh 3 ) 3 with methyl iodide were examined to test the generality of this type of reaction. The reaction of Ru(C 2 H 4 )(PPh 3 ) 3 with CD 3 I released CD 4 and CD 2 H 2 together with CD 3 H suggesting the involvement of α-hydrogen abstraction. (auth.)

  12. Ruthenium Dioxide Catalysts for the Selective Oxidation of Benzylamine to Benzonitrile: Investigating the Effect of Ruthenium Loading on Physical and Catalytic Properties

    Nordvang, Emily Catherine; Schill, Leonhard; Riisager, Anders

    2017-01-01

    The oxidative dehydrogenation of benzylamine to benzonitrile was studied in batch and continuous flow processes using ruthenium dioxide catalysts with varying ruthenium loadings. Increased conversions were observed in the continuous flow process compared with the batch process (up to 100% in the ......The oxidative dehydrogenation of benzylamine to benzonitrile was studied in batch and continuous flow processes using ruthenium dioxide catalysts with varying ruthenium loadings. Increased conversions were observed in the continuous flow process compared with the batch process (up to 100......% in the flow process compared with up to 92% in the batch process), with increased selectivity to benzonitrile (82 and 65%, respectively) and benzonitrile yields (84 and 58%, respectively). The major by-product was N-benzylidenebenzylamine. The ruthenium loading in the catalyst was successfully optimised...... and the most active catalyst had a ruthenium loading of 2.5-3.5 wt%....

  13. Hydrothermal synthesis and physicochemical properties of ruthenium(0) nanoparticles

    Dikhtiarenko, A., E-mail: dikhtiarenkoalla@uniovi.es [Departamento de Quimica Organica e Inorganica, Universidad de Oviedo - CINN, 33006 Oviedo (Spain); Khainakov, S.A.; Garcia, J.R.; Gimeno, J. [Departamento de Quimica Organica e Inorganica, Universidad de Oviedo - CINN, 33006 Oviedo (Spain); Pedro, I. de; Fernandez, J. Rodriguez [CITIMAC, Facultad de Ciencias, Universidad de Cantabria, 39005 Santander (Spain); Blanco, J.A. [Departamento de Fisica, Universidad de Oviedo, 33007 Oviedo (Spain)

    2012-09-25

    Highlights: Black-Right-Pointing-Pointer Ruthenium nanoparticles were synthesized by hydrothermal technique. Black-Right-Pointing-Pointer The average size of the nanoparticles are depend on the reducing agent used. Black-Right-Pointing-Pointer The magnetic response seems to be dominated by a paramagnetic contribution characteristic of the band electronic magnetism of the ruthenium(0) nanoparticles. - Abstract: The synthesis of ruthenium nanoparticles in hydrothermal conditions using mild reducing agents (succinic acid, ascorbic acid and sodium citrate) is reported. The shape of the nanoparticles depends on the type of the reducing agent, while the size is more influenced by the pH of the medium. The magnetic response seems to be dominated by a paramagnetic contribution characteristic of the band electronic magnetism of the nanoparticles.

  14. Device for separating ruthenium ion from spent fuel material

    Izumida, Tatsuo; Sasahira, Akira; Ozawa, Yoshihiro; Kawamura, Fumio.

    1988-01-01

    Purpose: To separate plutonium ions efficiently and selectively from organic solvent containing tributyl phosphate used in the main step of reprocessing process. Constitution: The device comprises, as the main constituent factor, a liquid-liquid contact device for bringing not water soluble organic solvent into contact with a nitric acid solution of spent fuel substances and a liquid-liquid contact-separation device for bringing an organic solvent solution containing spent fuel substances separated with nitric acid into contact again with nitric acid. Then, a device is disposed between two liquid-liquid contact devices for staying ruthenium ions and organic solvent for a sufficient time. In this way, ruthenium ions in the organic solvent containing butyl phosphate are gradually converted into complex compounds combined with tributyl phosphate thereby enabling to separate ruthenium ions efficiently and remarkably reduce the corrosion of equipments. (Horiuchi, T.)

  15. Thermodynamic data bases for multivalent elements: An example for ruthenium

    Rard, J.A.

    1987-11-01

    A careful consideration and understanding of fundamental chemistry, thermodynamics, and kinetics is absolutely essential when modeling predominance regions and solubility behavior of elements that exhibit a wide range of valence states. Examples of this are given using the ruthenium-water system at 298.15 K, for which a critically assessed thermochemical data base is available. Ruthenium exhibits the widest range of known aqueous solution valence states. Known solid anhydrous binary oxides of ruthenium are crystalline RuO 2 , RuO 4 , and possibly RuO 3 (thin film), and known hydroxides/hydrated oxides (all amorphous) are Ru(OH) 3 . H 2 O, RuO 2 . 2H 2 O, RuO 2 . H 2 O, and a poorly characterized Ru(V) hydrous oxide. Although the other oxides, hydroxides, and hydrous oxides are generally obtained as precipitates from aqueous solutions, they are thermodynamically unstable with regard to RuO 2 (cr) formation. Characterized aqueous species of ruthenium include RuO 4 (which slowly oxidizes water and which dissociates as a weak acid), RuO 4 - and RuO 4 2- (which probably contain lesser amounts of RuO 3 (OH) 2 - and RuO 3 (OH) 2 2- , respectively, and other species), Ru(OH) 2 2+ , Ru 4 (OH) 12 4+ , Ru(OH) 4 , Ru 3+ , Ru(OH) 2+ , Ru(OH) 2 + , Ru 2+ , and some hydroxytetramers with formal ruthenium valences of 3.75 ≥ Z ≥ 2.0. Potential pH diagrams of the predominance regions change significantly with concentration due to polymerization/depolymerization reactions. Failure to consider the known chemistry of ruthenium can yield large differences in predicted solubilities

  16. Method of removing clogging materials due to ruthenium precipitates and sealing them in device

    Hoshikawa, Tadahiro; Sasahira, Akira.

    1994-01-01

    In a facility, such as a reprocessing facility, for processing a solution containing a great amount of ruthenium, precipitates due to evaporated ruthenium and cooled NO x are brought into contact with each other to decompose the precipitates due to the evaporated ruthenium. Precipitates due to ruthenium evaporated from the solution are reacted with cooled NO x , and the precipitates of ruthenium are decomposed and returned to the solution in the form of extremely fine particles together with recycling flow from the inner wall of the device. Since the precipitates of ruthenium returned to the solution are stable, they are no more evaporated and precipitated on the inner wall of the device. In the solution processing device having a possibility of clogging, clogging can be prevented and the precipitates of ruthenium can be sealed by decomposing them. (T.M.)

  17. Ruthenium oxide resistors as sensitive elements of composite bolometers

    Benassai, M.; Gallinaro, G.; Gatti, F.; Siri, S.; Vitale, S.

    1988-01-01

    Bolometers for particle detection made with Ruthenium oxide thermistors could be produced by means of a simple technique on a variety of different materials as substrata. Preliminary results on alpha particle detection with devices realized using commercial RuO 2 thick film resistor (Tfr) are considered positive for devices operating between. 3 and .1 k and determined us to pursue further the idea. Ruthenium oxide resistors on sapphire at the moment are being prepared. The behaviour of these devices st temperatures lower than .1 k has to be investigated in more detail

  18. Determination of oxygen diffusion kinetics during thin film ruthenium oxidation

    Coloma Ribera, R., E-mail: r.colomaribera@utwente.nl; Kruijs, R. W. E. van de; Yakshin, A. E.; Bijkerk, F. [MESA+ Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands)

    2015-08-07

    In situ X-ray reflectivity was used to reveal oxygen diffusion kinetics for thermal oxidation of polycrystalline ruthenium thin films and accurate determination of activation energies for this process. Diffusion rates in nanometer thin RuO{sub 2} films were found to show Arrhenius behaviour. However, a gradual decrease in diffusion rates was observed with oxide growth, with the activation energy increasing from about 2.1 to 2.4 eV. Further exploration of the Arrhenius pre-exponential factor for diffusion process revealed that oxidation of polycrystalline ruthenium joins the class of materials that obey the Meyer-Neldel rule.

  19. Electrodeposition of ruthenium, rhodium and palladium from nitric acid and ionic liquid media: Recovery and surface morphology of the deposits

    Jayakumar, M.; Venkatesan, K.A.; Sudha, R. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu 603102 (India); Srinivasan, T.G., E-mail: tgs@igcar.gov.com [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu 603102 (India); Vasudeva Rao, P.R. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu 603102 (India)

    2011-07-15

    Research highlights: {yields} Platinum group metals are man-made noble metals. {yields} Electrochemical recovery of fission platinoids. {yields} Recovery from nitric acid medium. {yields} Recovery from ionic liquid medium. {yields} Platinoids with exotic surface morphologies. - Abstract: Electrodeposition is a promising technique for the recovery of platinum group metals with unique surface morphologies. The electrodeposition of palladium, ruthenium and rhodium from aqueous nitric acid, and non-aqueous 1-butyl-3-methylimidazolium chloride ionic liquid medium was studied at stainless steel electrode. The surface morphology and elemental composition of the resultant deposit were probed by scanning electron microscopy (SEM) and energy dispersive X-ray (EDS) analysis. Deposits with diverse surface morphologies and metal compositions were obtained by varying the composition of the electrolytic medium and applied potential. The results demonstrate the possibility of tailoring the morphologies of PGMs by controlling the composition and potential needed for electrodeposition.

  20. Development of a method for analyzing traces of ruthenium in plant materials and determination of the transfer factors soil/plant for ruthenium compounds from reprocessing plants

    Blasius, E.; Huth, R.; Neumann, W.

    1988-01-01

    In an artificial humous and sandy soil spiked with 106 Ru as RuO 2 and RuCl 3 , pasture grass was grown under artificial illumination in our laboratory. The amounts of ruthenium taken up by the plants were determined by γ-spectrometry. For open-air investigations with pasture grass, wheat and potatoes inactive ruthenium(III) chloride and ruthenium nitrosylchloride were used. Ruthenium was determined by electrothermal atomic absorption spectrometry (ETAAS) after destroying the organic material and concentrating the solution. The concentration and chemical form of the ruthenium exert an unimportant influence on the transfer factor. For the pasture-grass, the stems of wheat and the weed of potatoes it amounts to 0.00005 to 0.0015, for the ear of wheat to about 0.00005. In peeled potatoes there was no ruthenium detectable, therefore the limit of detection leads to a transfer factor ≤ 0.00001. So it is evident that ruthenium is little available for the roots of the plants. In the event of an accident in a nuclear plant the uptake of radioactive ruthenium by roots has only negligible radioecological consequences. This applies even if 50 years of ruthenium enrichment in the soil are assumed. (orig./RB)

  1. Application of the chemical properties of ruthenium to decontamination processes; L'application des proprietes chimiques du ruthenium a des procedes de decontamination

    Fontaine, A.; Berger, D. [Commissariat a l' Energie Atomique, Centre de Production de Plutonium, Marcoule (France). Centre d' Etudes Nucleaires

    1965-07-01

    The chemical properties of ruthenium in the form of an aqueous solution of the nitrate and of organic tributylphosphate solution are reviewed. From this data, some known examples are given: they demonstrate the processes of separation or of elimination of ruthenium from radioactive waste. (authors) [French] Les proprietes chimiques du ruthenium en solutions aqueuses nitriques et en solutions organiques de tributylphosphate, sont passees en revue. A partir de ces donnees, quelques exemples connus sont cites: ils exposent des procedes de separation ou d'elimination du ruthenium de dechets radioactifs. (auteurs)

  2. Application of the chemical properties of ruthenium to decontamination processes; L'application des proprietes chimiques du ruthenium a des procedes de decontamination

    Fontaine, A; Berger, D [Commissariat a l' Energie Atomique, Centre de Production de Plutonium, Marcoule (France). Centre d' Etudes Nucleaires

    1965-07-01

    The chemical properties of ruthenium in the form of an aqueous solution of the nitrate and of organic tributylphosphate solution are reviewed. From this data, some known examples are given: they demonstrate the processes of separation or of elimination of ruthenium from radioactive waste. (authors) [French] Les proprietes chimiques du ruthenium en solutions aqueuses nitriques et en solutions organiques de tributylphosphate, sont passees en revue. A partir de ces donnees, quelques exemples connus sont cites: ils exposent des procedes de separation ou d'elimination du ruthenium de dechets radioactifs. (auteurs)

  3. 环戊二烯基钌配合物催化的高选择性苯乙炔二聚反应%HIGHLY SELECTIVE CATALYTIC DIMERIZATION OF PHENYLACETYLENE BY CYCLOPENTADIENYL RUTHENIUM COMPLEXES

    金军挺; 黄吉玲; 陶晓春; 钱延龙

    1999-01-01

    @@ Transition metal vinylidene complexes (M=C=CHR) have attracted a great deal of attention in recent years as a new type of organometallic intermediates that may have unusual reactivity[1]. Their reactivity has been explored and their application to organic synthesis is developed[2]. Recent reports on the ruthenium-vinylidene complexes[3]suggest that the reaction of ruthenium-vinylidene complexes with a base generates the coordinatively unsaturated ruthenium acetylide species, which are involved in a number of catalytic and stoichiometric reactions of alkynes. For example,the coordinatively unsaturated ruthenium acetylide species C5Me5Ru(PPh3)-C≡CPh,formed from the reaction of the vinylidene complex C5Me5Ru(PPh3) (Cl)=C=CHPh with a base was reactive toward a variety of small molecules and active in catalytic dimerization of terminal alkynes[4]. The dimerization of terminal alkyne is an effective method of forming enynes, but its synthetic application in organic synthesis has been limited dueto low selectivity for dimeric products[5]. In this communication, we report that three ruthenium complexes were used as catalysts for the highly selective dimerization of phenylacetylene.

  4. Electro-volatilization of ruthenium in nitric medium: influences of ruthenium species nature and models solutions composition

    Mousset, F.

    2004-12-01

    Ruthenium is one of the fission products in the reprocessing of irradiated fuels that requires a specific processing management. Its elimination, upstream by the PUREX process, has been considered. A process, called electro-volatilization, which take advantage of the RuO 4 volatility, has been optimised in the present study. It consists in a continuous electrolysis of ruthenium solutions in order to generate RuO 4 species that is volatilized and easily trapped. This process goes to satisfying ruthenium elimination yields with RuNO(NO 3 ) 3 (H 2 O) 2 synthetic solutions but not with fuel dissolution solutions. Consequently, this work consisted in the speciation studies of dissolved ruthenium species were carried out by simulating fuel solutions produced by hot acid attack of several ruthenium compounds (Ru(0), RuO 2 ,xH 2 O, polymetallic alloy). In parallel with dissolution kinetic studies, the determination of dissolved species was performed using voltammetry, spectrometry and spectro-electrochemistry. The results showed the co-existence of Ru(IV) and RuNO(NO 2 ) 2 (H 2 O) 3 . Although these species are different from synthetic RuNO(NO 3 ) 3 (H 2 O) 2 , their electro-oxidation behaviour are similar. The electro-volatilization tests of these dissolution solutions yielded to comparable results as the synthetic RuNO(NO 3 ) 3 (H 2 O) 2 solutions. Then, complexity increase of models solutions was performed by in-situ generation of nitrous acid during ruthenium dissolution. Nitrous acid showed a catalytic effect on ruthenium dissolution. Its presence goes to quasi exclusively RuNO(NO 2 ) 2 (H 2 O) 3 species. It is also responsible of the strong n-bond formation between Ru 2+ and NO + . In addition, it has been shown that its reducing action on RuO 4 hinders the electro-volatilization process. Mn 2+ and Ce 3+ cations also reveal, but to a lesser extent, an electro-eater behaviour as well as Pu 4+ and Cr 3+ according to the thermodynamics data. These results allow one to

  5. Aerial Photography and Imagery, Ortho-Corrected, Washburn County had ortho/oblique photography flight done in April of 2009. Pictometry was contracted for the project., Published in 2009, 1:4800 (1in=400ft) scale, Washburn County Government.

    NSGIC Local Govt | GIS Inventory — Aerial Photography and Imagery, Ortho-Corrected dataset current as of 2009. Washburn County had ortho/oblique photography flight done in April of 2009. Pictometry...

  6. Experimental study of para- and ortho-H3+ recombination

    Plašil, R.; Varju, J.; Hejduk, M.; Dohnal, P.; Kotrík, T.; Glosík, J.

    2011-07-01

    Recombination of H3+ with electrons is a key process for many plasmatic environments. Recent experiments on storage ring devices used ion sources producing H3+ with enhanced populations of H3+ ions in the para nuclear spin configuration to shed light on the theoretically predicted faster recombination of para states. Although increased recombination rates were observed, no in situ characterization of recombining ions was performed. We present a state selective recombination study of para- and ortho-H3+ ions with electrons at 77 K in afterglow plasma in a He/Ar/H2 gas-mixture. Both spin configurations of H3+ have been observed in situ with a near infrared cavity ring down spectrometer (NIR-CRDS) using the two lowest energy levels of H3+. Using hydrogen with an enhanced population of H2 molecules in para states allowed us to influence the [para-H3+]/[ortho-H3+] ratio in the discharge and in the afterglow. We observed an increase in the measured effective recombination rate coefficients with the increase of the fraction of para-H3+. Measurements with different fractions of para-H3+ at otherwise identical conditions allowed us to determine the binary recombination rate coefficients for pure para-H3+ pαbin(77 K) = (2.0±0.4)×10-7 cm3s-1 and pure ortho-H3+ oαbin(77 K) = (4±3)×10-8 cm3s-1.

  7. Multicentre evaluation of the new ORTHO VISION® analyser.

    Lazarova, E; Scott, Y; van den Bos, A; Wantzin, P; Atugonza, R; Solkar, S; Carpio, N

    2017-10-01

    Implementation of fully automated analysers has become a crucial security step in the blood bank; it reduces human errors, allows standardisation and improves turnaround time (TAT). We aimed at evaluating the ease of use and the efficiency of the ORTHO VISION ® Analyser (VISION) in comparison to the ORTHO AutoVue ® Innova System (AutoVue) in six different laboratories. After initial training and system configuration, VISION was used in parallel to AutoVue following the daily workload, both automates being based on ORTHO BioVue ® System column agglutination technology. Each participating laboratory provided data and scored the training, system configuration, quality control, maintenance and system efficiency. A total of 1049 individual samples were run: 266 forward and reverse grouping and antibody screens with 10 urgent samples, 473 ABD forward grouping and antibody screens with 22 urgent samples, 160 ABD forward grouping, 42 antibody screens and a series of 108 specific case profiles. The VISION instrument was more rapid than the AutoVue with a mean performing test time of 27·9 min compared to 36 min; for various test type comparisons, the TAT data obtained from VISION was shorter than that from AutoVue. Moreover, VISION analysed urgent STAT samples faster. Regarding the ease of use, VISION was intuitive and user friendly. VISION is a robust, reproducible system performing the most types of analytical determinations needed for pre-transfusion testing today, thus accommodating a wide range of clinical needs. VISION brings appreciated new features that could further secure blood transfusions. © 2017 The Authors. Transfusion Medicine published by John Wiley & Sons Ltd on behalf of British Blood Transfusion Society.

  8. Magnetic anisotropy of graphene quantum dots decorated with a ruthenium adatom

    Igor Beljakov

    2013-07-01

    Full Text Available The creation of magnetic storage devices by decoration of a graphene sheet by magnetic transition-metal adatoms, utilizing the high in-plane versus out-of-plane magnetic anisotropy energy (MAE, has recently been proposed. This concept is extended in our density-functional-based modeling study by incorporating the influence of the graphene edge on the MAE. We consider triangular graphene flakes with both armchair and zigzag edges in which a single ruthenium adatom is placed at symmetrically inequivalent positions. Depending on the edge-type, the graphene edge was found to influence the MAE in opposite ways: for the armchair flake the MAE increases close to the edge, while the opposite is true for the zigzag edge. Additionally, in-plane pinning of the magnetization direction perpendicular to the edge itself is observed for the first time.

  9. Hydroformylation and kinetics of 1-hexene over ruthenium, cobalt and rhodium zerolite catalysts

    Wang, C.; Wei, W.

    1989-01-01

    In this paper, six kinds of catalysts were prepared by cation exchange with rhodium, ruthenium and cobalt chloropentaamino dichoride and zeolites. Effects such as support materials, PPH 3 to metal ratio, reaction temperature, total pressure, H 2 /CO ratio, reaction time and solvents have been investigated in an autoclave. The most favorable results of 1-hexene hydroformylation were obtained in the temperature range 100-150 degrees C at a pressure of 5.0MPa (H 2 /CO=1:1) and the addition of free PPh 3 . The bimetallic catalysts showed high catalytic activing for hydroformylation because of the synergistic effect of bimetallic systems. This paper reports the results of experiments and catalysts characterization by means of IR and XRD spectroscopy

  10. Synthesis of phosphonic acid derivatized bipyridine ligands and their ruthenium complexes.

    Norris, Michael R; Concepcion, Javier J; Glasson, Christopher R K; Fang, Zhen; Lapides, Alexander M; Ashford, Dennis L; Templeton, Joseph L; Meyer, Thomas J

    2013-11-04

    Water-stable, surface-bound chromophores, catalysts, and assemblies are an essential element in dye-sensitized photoelectrosynthesis cells for the generation of solar fuels by water splitting and CO2 reduction to CO, other oxygenates, or hydrocarbons. Phosphonic acid derivatives provide a basis for stable chemical binding on metal oxide surfaces. We report here the efficient synthesis of 4,4'-bis(diethylphosphonomethyl)-2,2'-bipyridine and 4,4'-bis(diethylphosphonate)-2,2'-bipyridine, as well as the mono-, bis-, and tris-substituted ruthenium complexes, [Ru(bpy)2(Pbpy)](2+), [Ru(bpy)(Pbpy)2](2+), [Ru(Pbpy)3](2+), [Ru(bpy)2(CPbpy)](2+), [Ru(bpy)(CPbpy)2](2+), and [Ru(CPbpy)3](2+) [bpy = 2,2'-bipyridine; Pbpy = 4,4'-bis(phosphonic acid)-2,2'-bipyridine; CPbpy = 4,4'-bis(methylphosphonic acid)-2,2'-bipyridine].

  11. The trans influence in mer-trichloronitridobis(triphenylarsine)ruthenium(VI)

    Magnussen, Magnus; Bendix, Jesper

    2003-01-01

    The title compound, mer-[RuCl(3)N(C(18)H(15)As)(2)], is the first structurally characterized example of a nitride complex in which ruthenium is six-coordinated to monodentate ligands only. The Ru[triple-bond]N bond length [1.6161 (15) A] is relatively long, and the trans influence of the nitride...

  12. Polystyrene with pendant mixed functional ruthenium(II)-terpyridine complexes

    Heller, M.; Schubert, U.S.

    2002-01-01

    A vinyl substituted 2,2:6,2-terpyridine and a mixed, bifunctional ruthenium(II)-terpyridine complex bearing a vinyl and a hydroxymethyl group are utilized as comonomers for radical copolymerization with styrene. The resulting polymers are characterized by means of UV-vis spectroscopy and gel

  13. Determination of oxygen diffusion kinetics during thin film ruthenium oxidation

    Coloma Ribera, R.; van de Kruijs, Robbert Wilhelmus Elisabeth; Yakshin, Andrey; Bijkerk, Frederik

    2015-01-01

    In situ X-ray reflectivity was used to reveal oxygen diffusion kinetics for thermal oxidation of polycrystalline ruthenium thin films and accurate determination of activation energies for this process. Diffusion rates in nanometer thin RuO2 films were found to show Arrhenius behaviour. However, a

  14. Electronic state of ruthenium deposited onto oxide supports: An XPS study taking into account the final state effects

    Larichev, Yurii V.; Moroz, Boris L.; Bukhtiyarov, Valerii I.

    2011-01-01

    The electronic state of ruthenium in the supported Ru/EO x (EO x = MgO, Al 2 O 3 or SiO 2 ) catalysts prepared by with the use of Ru(OH)Cl 3 or Ru(acac) 3 (acac = acetylacetonate) and reduced with H 2 at 723 K is characterized by X-ray photoelectron spectroscopy (XPS) in the Ru 3d, Cl 2p and O 1s regions. The influence of the final state effects (the differential charging and variation of the relaxation energy) on the binding energy (BE) of Ru 3d 5/2 core level measured for supported Ru nanoparticles is estimated by comparison of the Fermi levels and the modified Auger parameters determined for the Ru/EO x samples with the corresponding characteristics of the bulk Ru metal. It is found that the negative shift of the Ru 3d 5/2 peak which is observed in the spectrum of ruthenium deposited onto MgO (BE = 279.5-279.7 eV) with respect to that of Ru black (BE = 280.2 eV) or ruthenium supported on γ-Al 2 O 3 and SiO 2 (BE = 280.4 eV) is caused not by the transfer of electron density from basic sites of MgO, as considered earlier, but by the differential charging of the supported Ru particles compared with the support surface. Correction for the differential charging value reveals that the initial state energies of ruthenium in the Ru/EO x systems are almost identical (BE = 280.5 ± 0.1 eV) irrespectively of acid-base properties of the support, the mean size of supported Ru crystallites (within the range of 2-10 nm) and the surface Cl content. The results obtained suggest that the difference in ammonia synthesis activity between the Ru catalysts supported on MgO and on the acidic supports is accounted for by not different electronic state of ruthenium on the surface of these oxides but by some other reasons.

  15. Palladium(II)-catalyzed ortho-olefination of arenes applying sulfoxides as remote directing groups.

    Wang, Binjie; Shen, Chuang; Yao, Jinzhong; Yin, Hong; Zhang, Yuhong

    2014-01-03

    A novel palladium-catalyzed ortho-C(sp(2))-H olefination protocol has been developed by the use of sulfoxide as the directing group. Importantly, relatively remote coordination can be accessed to achieve the ortho olefination of benzyl, 2-arylethyl, and 3-arylpropenyl sulfoxide substrates, and the olefinated sulfoxide can be easily transformed to other functionalities.

  16. Synthesis of Ortho Substituted Arylboronic Esters by in Situ Trapping of Unstable Lithio Intermediates

    Kristensen, Jesper Langgaard; Lysén, M.; Vedsø, Per

    2001-01-01

    matrix presented Ortho lithiation-in situ boration using lithium 2,2,6,6-tetramethylpiperidide (LTMP) in combination with triisopropylborate (B(OiPr) ) is a highly efficient and experimentally straightforward process for the preparation of ortho substituted arylboronic esters. The mild reaction c...

  17. Inhibition of LPS-induced splenocyte proliferation by ortho-substituted polychlorinated biphenyl congeners

    Smithwick, L. Ashley; Smith, Andrew; Quensen, John F.; Stack, Allison; London, Lucille; Morris, Pamela J.

    2003-01-01

    Polychlorinated biphenyls (PCBs) are persistent environmental contaminants, and their ubiquitous nature has prompted studies of their potential health hazards. As a result of their lipophilic nature, PCBs accumulate in breast milk and subsequently affect the health of offspring of exposed individuals. Biological effects of PCBs in animals have mostly been attributed to coplanar congeners, although effects of ortho congeners also have been demonstrated. To investigate the relationship of immunotoxicity and chlorine substitution pattern, the effects of PCB congeners and mixtures of ortho and non-ortho-substituted constituents of Aroclor 1242 on splenocytes from C57B1/6 mice were examined. The immunotoxic endpoints investigated included splenocyte viability, lipopolysaccharide (LPS)-induced splenocyte proliferation, and LPS-induced antibody secretion. Congeners with multiple ortho chlorines preferentially inhibited splenocyte proliferation as compared with non- or mono-ortho-substituted congeners. However, mixtures of non- and mono-ortho-substituted congeners and multi-ortho-substituted congeners inhibited LPS-induced splenocyte proliferation and antibody secretion at similar concentrations. Exposure of splenocytes to these mixtures did not activate the aryl hydrocarbon receptor (AhR) signal transduction pathway. These results suggest individual multi-ortho-substituted congeners preferentially inhibit LPS-induced splenocyte proliferation, while congeners not exhibiting an effect individually may have additive effects in a mixture to produce an immunotoxic response through an AhR-independent pathway

  18. Ruthenium based redox flow battery for solar energy storage

    Chakrabarti, Mohammed Harun; Roberts, Edward Pelham Lindfield; Bae, Chulheung; Saleem, Muhammad

    2011-01-01

    Research highlights: → Undivided redox flow battery employing porous graphite felt electrodes was used. → Ruthenium acetylacetonate dissolved in acetonitrile was the electrolyte. → Charge/discharge conditions were determined for both 0.02 M and 0.1 M electrolytes. → Optimum power output of 0.180 W was also determined for 0.1 M electrolyte. → 55% voltage efficiency was obtained when battery was full of electrolytes. -- Abstract: The technical performance for the operation of a stand alone redox flow battery system for solar energy storage is presented. An undivided reactor configuration has been employed along with porous graphite felt electrodes and ruthenium acetylacetonate as electrolyte in acetonitrile solvent. Limiting current densities are determined for concentrations of 0.02 M and 0.1 M ruthenium acetylacetonate. Based on these, operating conditions for 0.02 M ruthenium acetylacetonate are determined as charging current density of 7 mA/cm 2 , charge electrolyte superficial velocity of 0.0072 cm/s (through the porous electrodes), discharge current density of 2 mA/cm 2 and discharge electrolyte superficial velocity of 0.0045 cm/s. An optimum power output of 35 mW is also obtained upon discharge at 2.1 mA/cm 2 . With an increase in the concentration of ruthenium species from 0.02 M to 0.1 M, the current densities and power output are higher by a factor of five approximately (at same superficial velocities) due to higher mass transport phenomenon. Moreover at 0.02 M concentration the voltage efficiency is better for battery full of electrolytes prior to charging (52.1%) in comparison to an empty battery (40.5%) due to better mass transport phenomenon. Voltage efficiencies are higher as expected at concentrations of 0.1 M ruthenium acetylacetonate (55% when battery is full of electrolytes and 48% when empty) showing that the all-ruthenium redox flow battery has some promise for future applications in solar energy storage. Some improvements for the

  19. Synthesis and Catalytic Hydrogen Transfer Reaction of Ruthenium(II) Complex

    Son, Jung Ik; Kim, Aram; Noh, Hui Bog; Lee, Hyun Ju; Shim, Yoon Bo; Park, Kang Hyun

    2012-01-01

    The ruthenium(II) complex [Ru(bpy) 2 -(PhenTPy)] was synthesized, and used for the transfer hydrogenation of ketones and the desired products were obtained in good yield. Based on the presented results, transition-metal complexes can be used as catalysts for a wide range of organic transformations. The relationship between the electro-reduction current density and temperature are being examined in this laboratory. Attempts to improve the catalytic activity and determine the transfer hydrogenation mechanism are currently in progress. The catalytic hydrogenation of a ketone is a basic and critical process for making many types of alcohols used as the final products and precursors in the pharmaceutical, agrochemical, flavor, fragrance, materials, and fine chemicals industries. The catalytic hydrogenation process developed by Noyori is a very attractive process. Formic acid and 2-propanol have been used extensively as hydrogenation sources. The advantage of using 2-propanol as a hydrogen source is that the only side product will be acetone, which can be removed easily during the workup process. Hydrogen transfer (HT) catalysis, which generates alcohols through the reduction of ketones, is an attractive protocol that is used widely. Ruthenium(II) complexes are the most useful catalysts for the hydrogen transfer (HT) of ketones. In this method, a highly active catalytic system employs a transition metal as a catalyst to synthesize alcohols, and is a replacement for the hydrogen-using hydrogenation process. The most active system is based on Ru, Rh and Ir, which includes a nitrogen ligand that facilitates the formation of a catalytically active hydride and phosphorus

  20. Synthesis and Catalytic Hydrogen Transfer Reaction of Ruthenium(II) Complex

    Son, Jung Ik; Kim, Aram; Noh, Hui Bog; Lee, Hyun Ju; Shim, Yoon Bo; Park, Kang Hyun [Pusan National University, Busan (Korea, Republic of)

    2012-01-15

    The ruthenium(II) complex [Ru(bpy){sub 2}-(PhenTPy)] was synthesized, and used for the transfer hydrogenation of ketones and the desired products were obtained in good yield. Based on the presented results, transition-metal complexes can be used as catalysts for a wide range of organic transformations. The relationship between the electro-reduction current density and temperature are being examined in this laboratory. Attempts to improve the catalytic activity and determine the transfer hydrogenation mechanism are currently in progress. The catalytic hydrogenation of a ketone is a basic and critical process for making many types of alcohols used as the final products and precursors in the pharmaceutical, agrochemical, flavor, fragrance, materials, and fine chemicals industries. The catalytic hydrogenation process developed by Noyori is a very attractive process. Formic acid and 2-propanol have been used extensively as hydrogenation sources. The advantage of using 2-propanol as a hydrogen source is that the only side product will be acetone, which can be removed easily during the workup process. Hydrogen transfer (HT) catalysis, which generates alcohols through the reduction of ketones, is an attractive protocol that is used widely. Ruthenium(II) complexes are the most useful catalysts for the hydrogen transfer (HT) of ketones. In this method, a highly active catalytic system employs a transition metal as a catalyst to synthesize alcohols, and is a replacement for the hydrogen-using hydrogenation process. The most active system is based on Ru, Rh and Ir, which includes a nitrogen ligand that facilitates the formation of a catalytically active hydride and phosphorus.

  1. Mesoporous Transition Metal Oxides for Supercapacitors

    Wang, Yan; Guo, Jin; Wang, Tingfeng; Shao, Junfeng; Wang, Dong; Yang, Ying-Wei

    2015-01-01

    Recently, transition metal oxides, such as ruthenium oxide (RuO2), manganese dioxide (MnO2), nickel oxides (NiO) and cobalt oxide (Co3O4), have been widely investigated as electrode materials for pseudo-capacitors. In particular, these metal oxides with mesoporous structures have become very hot nanomaterials in the field of supercapacitors owing to their large specific surface areas and suitable pore size distributions. The high specific capacities of these mesoporous metal oxides are result...

  2. Poly(ortho esters)--from concept to reality.

    Heller, Jorge; Barr, John

    2004-01-01

    The development of poly(ortho esters) dates back to the early 1970s, and during that time, four distinct families were developed. These polymers can be prepared by a transesterification reaction or by the addition of polyols to diketene acetals, and it is the latter method that has proven to be preferred one. The latest polymer, now under intense development, incorporates a latent acid segment in the polymer backbone that takes advantage of the acid-labile nature of the ortho ester linkages and allows control over erosion rates. By use of diols having selected chain flexibility, polymers that range from hard, brittle materials to materials that have a gel-like consistency at room temperature can be obtained. Drug release from solid materials will be illustrated with 5-fluorouacil and bovine serum albumin, and drug release from gel-like materials will be illustrated with mepivacaine, now in Phase II clinical trials as a delivery system to treat post-operative pain. A brief summary of preclinical toxicology studies is also presented.

  3. Recommendation of ruthenium source for sludge batch flowsheet studies

    Woodham, W. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-09-13

    Included herein is a preliminary analysis of previously-generated data from sludge batches 7a, 7b, 8, and 9 sludge simulant and real-waste testing, performed to recommend a form of ruthenium for future sludge batch simulant testing under the nitric-formic flowsheet. Focus is given to reactions present in the Sludge Receipt and Adjustment Tank cycle, given that this cycle historically produces the most changes in chemical composition during Chemical Process Cell processing. Data is presented and analyzed for several runs performed under the nitric-formic flowsheet, with consideration given to effects on the production of hydrogen gas, nitrous oxide gas, consumption of formate, conversion of nitrite to nitrate, and the removal and recovery of mercury during processing. Additionally, a brief discussion is given to the effect of ruthenium source selection under the nitric-glycolic flowsheet. An analysis of data generated from scaled demonstration testing, sludge batch 9 qualification testing, and antifoam degradation testing under the nitric-glycolic flowsheet is presented. Experimental parameters of interest under the nitric-glycolic flowsheet include N2O production, glycolate destruction, conversion of glycolate to formate and oxalate, and the conversion of nitrite to nitrate. To date, the number of real-waste experiments that have been performed under the nitric-glycolic flowsheet is insufficient to provide a complete understanding of the effects of ruthenium source selection in simulant experiments with regard to fidelity to real-waste testing. Therefore, a determination of comparability between the two ruthenium sources as employed under the nitric-glycolic flowsheet is made based on available data in order to inform ruthenium source selection for future testing under the nitric-glycolic flowsheet.

  4. Catalytic transformation of carbon dioxide and methane into syngas over ruthenium and platinum supported hydroxyapatites

    Rêgo De Vasconcelos, Bruna; Zhao, Lulu; Sharrock, Patrick; Nzihou, Ange; Pham Minh, Doan, E-mail: doan.phamminh@mines-albi.fr

    2016-12-30

    Highlights: • Formation of nanoparticles of Pt and Ru on hydroxyapatite surface support (HAP). • Pt catalyst more active and stable than Ru catalyst in dry reforming of methane (DRM). • Low carbon deposition on the surface of Pt catalyst after reaction. • Quantification of water as by-product of the reaction for the first time. • Good mass balance of the reaction. - Abstract: This work focused on the catalytic transformation of methane (CH{sub 4}) and carbon dioxide (CO{sub 2}) into syngas (mixture of CO and H{sub 2}). Ruthenium- and platinum-based catalysts were prepared using hydroxyapatite (HAP) as catalyst support. Different methods for metal deposition were used including incipient wetness impregnation (IWI), excess liquid phase impregnation (LIM), and cationic exchange (CEX). Metal particle size varied in large range from less than 1 nm to dozens nm. All catalysts were active at 400–700 °C but only Pt catalyst prepared by IWI method (Pt/HAP IWI) was found stable. The catalytic performance of Pt/HAP IWI could be comparable with the literature data on noble metal-based catalysts, prepared on metal oxide supports. For the first time, water was experimentally quantified as a by-product of the reaction. This helped to correctly buckle the mass balance of the process.

  5. Catalytic transformation of carbon dioxide and methane into syngas over ruthenium and platinum supported hydroxyapatites

    Rêgo De Vasconcelos, Bruna; Zhao, Lulu; Sharrock, Patrick; Nzihou, Ange; Pham Minh, Doan

    2016-01-01

    Highlights: • Formation of nanoparticles of Pt and Ru on hydroxyapatite surface support (HAP). • Pt catalyst more active and stable than Ru catalyst in dry reforming of methane (DRM). • Low carbon deposition on the surface of Pt catalyst after reaction. • Quantification of water as by-product of the reaction for the first time. • Good mass balance of the reaction. - Abstract: This work focused on the catalytic transformation of methane (CH 4 ) and carbon dioxide (CO 2 ) into syngas (mixture of CO and H 2 ). Ruthenium- and platinum-based catalysts were prepared using hydroxyapatite (HAP) as catalyst support. Different methods for metal deposition were used including incipient wetness impregnation (IWI), excess liquid phase impregnation (LIM), and cationic exchange (CEX). Metal particle size varied in large range from less than 1 nm to dozens nm. All catalysts were active at 400–700 °C but only Pt catalyst prepared by IWI method (Pt/HAP IWI) was found stable. The catalytic performance of Pt/HAP IWI could be comparable with the literature data on noble metal-based catalysts, prepared on metal oxide supports. For the first time, water was experimentally quantified as a by-product of the reaction. This helped to correctly buckle the mass balance of the process.

  6. A rational repeating template method for synthesis of 2D hexagonally ordered mesoporous precious metals.

    Takai, Azusa; Doi, Yoji; Yamauchi, Yusuke; Kuroda, Kazuyuki

    2011-03-01

    A repeating template method is presented for the synthesis of mesoporous metals with 2D hexagonal mesostructures. First, a silica replica (i.e., silica nanorods arranged periodically) is prepared by using 2D hexagonally ordered mesoporous carbon as the template. After that, the obtained silica replica is used as the second template for the preparation of mesoporous ruthenium. After the ruthenium species are introduced into the silica replica, the ruthenium species are then reduced by a vapor-infiltration method by using the reducing agent dimethylamine borane. After the ruthenium deposition, the silica is chemically removed. Analysis by transmission and scanning electron microscopies, a nitrogen-adsorption-desorption isotherm, and small-angle X-ray scattering revealed that the mesoporous ruthenium had a 2D hexagonal mesostructure, although the mesostructural ordering is decreased compared to that of the original mesoporous carbon template. This method is widely applicable to other metal systems. By changing the metal species introduced into the silica replica, several mesoporous metals (palladium and platinum) can be synthesized. Ordered mesoporous ruthenium and palladium, which are not easily attainable by the soft-templating methods, can be prepared. This study has overcome the composition variation limitations of the soft-templating method. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. The origin of the selectivity and activity of ruthenium-cluster catalysts for fuel-cell feed-gas purification: a gas-phase approach.

    Lang, Sandra M; Bernhardt, Thorsten M; Krstić, Marjan; Bonačić-Koutecký, Vlasta

    2014-05-19

    Gas-phase ruthenium clusters Ru(n)(+) (n=2-6) are employed as model systems to discover the origin of the outstanding performance of supported sub-nanometer ruthenium particles in the catalytic CO methanation reaction with relevance to the hydrogen feed-gas purification for advanced fuel-cell applications. Using ion-trap mass spectrometry in conjunction with first-principles density functional theory calculations three fundamental properties of these clusters are identified which determine the selectivity and catalytic activity: high reactivity toward CO in contrast to inertness in the reaction with CO2; promotion of cooperatively enhanced H2 coadsorption and dissociation on pre-formed ruthenium carbonyl clusters, that is, no CO poisoning occurs; and the presence of Ru-atom sites with a low number of metal-metal bonds, which are particularly active for H2 coadsorption and activation. Furthermore, comprehensive theoretical investigations provide mechanistic insight into the CO methanation reaction and discover a reaction route involving the formation of a formyl-type intermediate. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Partitioning of rhodium and ruthenium between Pd–Rh–Ru and (Ru,Rh)O{sub 2} solid solutions in high-level radioactive waste glass

    Sugawara, Toru, E-mail: toru@gipc.akita-u.ac.jp [Center for Engineering Science, Akita University, 1-1, Tegatagakuenmachi, Akita City, Akita 010-8502 (Japan); Ohira, Toshiaki [Center for Engineering Science, Akita University, 1-1, Tegatagakuenmachi, Akita City, Akita 010-8502 (Japan); Komamine, Satoshi; Ochi, Eiji [Research and Development Department, Reprocessing Business Division, Japan Nuclear Fuel Limited, 4-108, Okitsuke, Obuchi, Rokkasho-mura, Aomori 039-3212 (Japan)

    2015-10-15

    The partitioning of rhodium and ruthenium between Pd–Rh–Ru alloy with a face-centered cubic (FCC) structure and (Ru,Rh)O{sub 2} solid solution has been investigated between 1273 and 1573 K at atmospheric oxygen fugacity. The rhodium and ruthenium contents in FCC increase, while the RhO{sub 2} content in (Ru,Rh)O{sub 2} decreases with increasing temperature due to progressive reduction of the system. Based on the experimental results and previously reported thermodynamic data, the thermodynamic mixing properties of FCC phase and (Ru,Rh)O{sub 2} have been calibrated in an internally consistent manner. Phase equilibrium of platinum grope metals in an HLW glass was calculated by using the obtained thermodynamic parameters.

  9. Study on volatilization mechanism of ruthenium tetroxide from nitrosyl ruthenium nitrate by using mass spectrometer

    Kato, Tetsuya, E-mail: tkato@criepi.denken.or.jp [Nuclear Technology Research Laboratory, Central Research Institute of Electric Power Industry, 2-11-1 Iwado-kita, Komae-shi, Tokyo 201-8511 (Japan); Usami, Tsuyoshi; Tsukada, Takeshi [Nuclear Technology Research Laboratory, Central Research Institute of Electric Power Industry, 2-11-1 Iwado-kita, Komae-shi, Tokyo 201-8511 (Japan); Shibata, Yuki; Kodama, Takashi [Safety Technology Division, Japan Nuclear Fuel Ltd., Obuchi, Rokkasho-mura, Aomori 039-3212 (Japan)

    2016-10-15

    In a cooling malfunction accident of a high-level liquid waste (HLLW) tank, behavior of ruthenium (Ru) attracts much attention, since Ru could be oxidized to a volatile chemical form in the boiling and drying of HLLW, and part of radioactive Ru can potentially be released to the environment. In this study, nitrosyl Ru nitrate (Ru(NO)(NO{sub 3}){sub 3}) dissolved in nitric acid (HNO{sub 3}), which is commonly contained in a simulated HLLW, was dried and heated up to 723 K, and the evolved gas was introduced into a mass spectrometer. The well-known volatile species, ruthenium tetroxide (RuO{sub 4}) was detected in a temperature range between 390 K and 500 K with the peak top around 440 K. Various gases such as HNO{sub 3}, nitrogen dioxide (NO{sub 2}), nitrogen monoxide (NO) also evolved due to evaporation of the nitric acid and decomposition of the nitrate ions. The ion current of RuO{sub 4} seems to increase with the increasing decomposition of nitrate, while the evaporation of HNO{sub 3} decreases. More volatilization of RuO{sub 4} was observed from the HNO{sub 3} solution containing not only Ru(NO)(NO{sub 3}){sub 3} but also cerium nitrate (Ce(NO{sub 3}){sub 3}·6H{sub 2}O) which was added for extra supply of nitrate ion, compared with that from the HNO{sub 3} solution containing only Ru(NO)(NO{sub 3}){sub 3}. These experimental results suggest that Ru could be oxidized to form RuO{sub 4} by the nitrate ion as well as HNO{sub 3}. - Graphical abstract: Ion current intensities of the mass numbers corresponding to O, NO, O{sub 2}, NO{sub 2}, HNO{sub 3}, and RuO{sub 4} obtained in mass spectrometry for dried nitric acid solution containing Ru(NO)(NO{sub 3}){sub 3}. Heating rate: 5 K min{sup −1}, sample solution weight: 6.61 mg, contained Ru weight: 0.56 mg. The ion current of RuO{sub 4} increases with the increasing decomposition of nitrate, while the evaporation of HNO{sub 3} decreases. - Highlights: • Nitrosyl Ru nitrate (Ru(NO)(NO{sub 3}){sub 3}) dissolved in

  10. C-N bond cleavage of anilines by a (salen)ruthenium(VI) nitrido complex.

    Man, Wai-Lun; Xie, Jianhui; Pan, Yi; Lam, William W Y; Kwong, Hoi-Ki; Ip, Kwok-Wa; Yiu, Shek-Man; Lau, Kai-Chung; Lau, Tai-Chu

    2013-04-17

    We report experimental and computational studies of the facile oxidative C-N bond cleavage of anilines by a (salen)ruthenium(VI) nitrido complex. We provide evidence that the initial step involves nucleophilic attack of aniline at the nitrido ligand of the ruthenium complex, which is followed by proton and electron transfer to afford a (salen)ruthenium(II) diazonium intermediate. This intermediate then undergoes unimolecular decomposition to generate benzene and N2.

  11. Ruthenium(III Chloride Catalyzed Acylation of Alcohols, Phenols, and Thiols in Room Temperature Ionic Liquids

    Mingzhong Cai

    2009-09-01

    Full Text Available Ruthenium(III chloride-catalyzed acylation of a variety of alcohols, phenols, and thiols was achieved in high yields under mild conditions (room temperature in the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6]. The ionic liquid and ruthenium catalyst can be recycled at least 10 times. Our system not only solves the basic problem of ruthenium catalyst reuse, but also avoids the use of volatile acetonitrile as solvent.

  12. The determination, by atomic-absorption spectrophotometry using electrothermal atomization, of platinum, palladium, rhodium, ruthenium, and iridium

    Haines, J.; Robert, R.V.D.

    1982-01-01

    A method that involves measurement by atomic-absorption spectrophotometry using electrothermal atomization has been developed for the determination of trace quantities of platinum, palladium, rhodium, ruthenium, and iridium in mineralogical samples. The elements are separated and concentrated by fusion, nickel sulphide being used as the collector, and the analyte elements are measured in the resulting acid solution. An organic extraction procedure was found to offer no advantages over the proposed method. Mutual interferences between the five platinum-group metals examined, as well as interferences from gold, silver, and nickel were determined. The accuracy of the measurement was established by the analysis of a platinum-ore reference material. The lower limits of determination of each of the analyte elements in a sample material are as follows: platinum 1,6μg/l, palladium 0,2μg/1, rhodium 0,5μg/l, ruthenium 3μg/l, and iridium 2,5μg/l. The relative standard deviations range from 0,05 for rhodium to 0.08 for iridium. The method, which is described in detail in the Appendix, is applicable to the determination of these elements in ores, tailings, and geological materials in which the total concentration of the noble metals is less than 1g/t

  13. Experiments on the behaviour of ruthenium in air ingress accidents - Progress report

    Kaerkelae, T.; Backman, U.; Auvinen, A.; Ziliacus, R.; Lipponen, M.; Kekki, T.; Tapper, U.; Jokiniemi, J.

    2006-02-01

    During routine nuclear reactor operation, ruthenium will accumulate in the fuel in relatively high concentrations. In an accident in a nuclear power plant it is possible that air gets into contact with the reactor core. In this case ruthenium can oxidise and form volatile ruthenium species, RuO3 and RuO4, which can be transported into the containment. In order to estimate the amount of gaseous ruthenium species it is of interest to know, how it is formed and how it behaves. In our experiments RuO2 is exposed to diverse oxidising atmospheres at a relatively high temperature. In this report, the experimental system for the ruthenium behaviour study is presented. Also preliminary results from experiments carried out during year 2005 are reported. In the experiments gaseous ruthenium oxides were produced in a furnace. Upon cooling RuO2 aerosol particles were formed in the system. They were removed with plane filters from the gas stream. Gaseous ruthenium species were trapped in 1M NaOH-water solution, which is capable of trapping RuO4 totally. Ruthenium in the solution was filtered for analysis. The determination of ruthenium both in aerosol and in liquid filters was made using instrumental neutron activation analysis (INAA). In order to close mass balance and achieve better time resolution three experiment using radioactive tracer were carried out. (au)

  14. Optimization of screen-printed ruthenium dioxide electrodes for pH measurements

    Wyzkiewicz, I.

    2002-01-01

    Optimization of disposable, screen-printed pH-sensors based on ruthenium dioxide is described in this paper. The electrodes were prepared with the use of thick-film technology. The pH-sensitive layers were deposited onto polyester foil. Polymer graphite paste containing ruthenium dioxide from 0% to 90% has been investigated. The dependence of the pH-sensitive layers related to ruthenium dioxide content is presented. The investigation proved that the electrodes containing 40-60% ruthenium dioxide exhibit linear high sensitivity (∼ 50 mV/pH) in the wide range of pH (2 - 11) as well as very good reproducibility. (author)

  15. Ruthenium determination in new composite materials by coulometric titration with generated iron(2)

    Butakova, N.A.; Oganesyan, L.B.

    1983-01-01

    A coulometric technique is developed for ruthenium (4) titration with generated iron (2) in a mixture of hydrochloric-, sulfuric- and phosphoric acids with potentiometric and biammetric indication of the final titration point. Bi (3), Pd (2), Nb (5), Pt (4) Pb (2), Rh (3) do not interfere with the titration. Together with Ru (4) titrated are Ir (4), V (5), Au (3). The method is applied to analyze commercial samples of ruthenium dioxides, lead- and bismuth ruthenites, ruthenium pentafluorides containing 30-80% of ruthenium. The Ssub(r) values do not exceed 0.002

  16. Surface and sub-surface thermal oxidation of thin ruthenium films

    Coloma Ribera, R.; Kruijs, R. W. E. van de; Yakshin, A. E.; Bijkerk, F. [MESA+ Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands); Kokke, S.; Zoethout, E. [FOM Dutch Institute for Fundamental Energy Research (DIFFER), P.O. Box 1207, 3430 BE Nieuwegein (Netherlands)

    2014-09-29

    A mixed 2D (film) and 3D (nano-column) growth of ruthenium oxide has been experimentally observed for thermally oxidized polycrystalline ruthenium thin films. Furthermore, in situ x-ray reflectivity upon annealing allowed the detection of 2D film growth as two separate layers consisting of low density and high density oxides. Nano-columns grow at the surface of the low density oxide layer, with the growth rate being limited by diffusion of ruthenium through the formed oxide film. Simultaneously, with the growth of the columns, sub-surface high density oxide continues to grow limited by diffusion of oxygen or ruthenium through the oxide film.

  17. Experiments on the behaviour of ruthenium in air ingress accidents - Progress report

    Kaerkelae, T.; Backman, U.; Auvinen, A.; Ziliacus, R.; Lipponen, M.; Kekki, T.; Tapper, U.; Jokiniemi, J. [VTT Technical Research Centre of Finland (Finland)

    2006-02-15

    During routine nuclear reactor operation, ruthenium will accumulate in the fuel in relatively high concentrations. In an accident in a nuclear power plant it is possible that air gets into contact with the reactor core. In this case ruthenium can oxidise and form volatile ruthenium species, RuO3 and RuO4, which can be transported into the containment. In order to estimate the amount of gaseous ruthenium species it is of interest to know, how it is formed and how it behaves. In our experiments RuO2 is exposed to diverse oxidising atmospheres at a relatively high temperature. In this report, the experimental system for the ruthenium behaviour study is presented. Also preliminary results from experiments carried out during year 2005 are reported. In the experiments gaseous ruthenium oxides were produced in a furnace. Upon cooling RuO2 aerosol particles were formed in the system. They were removed with plane filters from the gas stream. Gaseous ruthenium species were trapped in 1M NaOH-water solution, which is capable of trapping RuO4 totally. Ruthenium in the solution was filtered for analysis. The determination of ruthenium both in aerosol and in liquid filters was made using instrumental neutron activation analysis (INAA). In order to close mass balance and achieve better time resolution three experiment using radioactive tracer were carried out. (au)

  18. Stability of N-( ortho-hydroxynaphthylmethylene)methylamines and their tautomers

    Dobosz, Robert; Skotnicka, Agnieszka; Rozwadowski, Zbigniew; Dziembowska, Teresa; Gawinecki, Ryszard

    2010-08-01

    Thermodynamic parameters of the proton transfer equilibrium for three isomeric N-( ortho-hydroxynaphthylmethylene)methylamines have been determined by use of the temperature NMR data and deuterium isotope effects on 13C chemical shifts for their solutions in CDCl 3, CD 3CN and DMSO- d6. The DFT geometry optimization as well as calculation of the energies, dipole moments and HOMA (aromaticity) parameters for the OH and NH tautomers in vacuum and in solution has been performed. Interpretation of origin of the observed differences in the equilibrium constants for the three isomers studied is based on the differences in competition between π-electron delocalization in the quasi-ring involving the intramolecular hydrogen bond, differences in the polarity and on the peri interactions.

  19. Post surgical pain management with poly(ortho esters).

    Barr, John; Woodburn, Kathryn W; Ng, Steven Y; Shen, Hui-Rong; Heller, Jorge

    2002-10-16

    Poly(ortho esters), POE, are synthetic bioerodible polymers that can be prepared as solid materials, or as viscous, injectable polymers. These materials have evolved through a number of families, and the latest member of this family, POE IV, is particularly well suited to drug delivery since latent acid is integrated into the polymer backbone, thereby, modulating surface erosion. POE IV predominantly undergoes surface erosion and is able to moderate drug release over periods from days to many months. One indication in which the POE IV polymer is currently being investigated is in sustained post-surgical pain management. The local anesthetic agent, mepivacaine, has been incorporated into a viscous, injectable POE IV and its potential to provide longer-acting anesthesia has been explored in non-clinical models.

  20. Iodide Ion Pairing with Highly Charged Ruthenium Polypyridyl Cations in CH3CN.

    Swords, Wesley B; Li, Guocan; Meyer, Gerald J

    2015-05-04

    A series of three highly charged cationic ruthenium(II) polypyridyl complexes of the general formula [Ru(deeb)3-x(tmam)x](PF6)2x+2, where deeb is 4,4'-diethyl ester-2,2'-bipyridine and tmam is 4,4'-bis[(trimethylamino)methyl]-2,2'-bipyridine, were synthesized and characterized and are referred to as 1, 2, or 3 based on the number of tmam ligands. Crystals suitable for X-ray crystallography were obtained for the homoleptic complex 3, which was found to possess D3 symmetry over the entire ruthenium complex. The complexes displayed visible absorption spectra typical of metal-to-ligand charge-transfer (MLCT) transitions. In acetonitrile, quasi-reversible waves were assigned to Ru(III/II) electron transfer, with formal reduction potentials that shifted negative as the number of tmam ligands was increased. Room temperature photoluminescence was observed in acetonitrile with quantum yields of ϕ ∼ 0.1 and lifetimes of τ ∼ 2 μs. The spectroscopic and electrochemical data were most consistent with excited-state localization on the deeb ligand for 1 and 2 and on the tmam ligand for 3. The addition of tetrabutylammonium iodide to the complexes dissolved in a CH3CN solution led to changes in the UV-vis absorption spectra consistent with ion pairing. A Benesi-Hildebrand-type analysis of these data revealed equilibrium constants that increased with the cationic charge 1 10(8) s(-1). The possible relevance of this work to solar energy conversion and dye-sensitized solar cells is discussed.

  1. Electronic structure investigation of atomic layer deposition ruthenium(oxide) thin films using photoemission spectroscopy

    Schaefer, Michael, E-mail: mvschaefer@mail.usf.edu, E-mail: schlaf@mail.usf.edu [Department of Physics, University of South Florida, Tampa, Florida 33620 (United States); Schlaf, Rudy, E-mail: mvschaefer@mail.usf.edu, E-mail: schlaf@mail.usf.edu [Department of Electrical Engineering, University of South Florida, Tampa, Florida 33620 (United States)

    2015-08-14

    Analyzing and manipulating the electronic band line-up of interfaces in novel micro- and nanoelectronic devices is important to achieve further advancement in this field. Such band alignment modifications can be achieved by introducing thin conformal interfacial dipole layers. Atomic layer deposition (ALD), enabling angstrom-precise control over thin film thickness, is an ideal technique for this challenge. Ruthenium (Ru{sup 0}) and its oxide (RuO{sub 2}) have gained interest in the past decade as interfacial dipole layers because of their favorable properties like metal-equivalent work functions, conductivity, etc. In this study, initial results of the electronic structure investigation of ALD Ru{sup 0} and RuO{sub 2} films via photoemission spectroscopy are presented. These experiments give insight into the band alignment, growth behavior, surface structure termination, and dipole formation. The experiments were performed in an integrated vacuum system attached to a home-built, stop-flow type ALD reactor without exposing the samples to the ambient in between deposition and analysis. Bis(ethylcyclopentadienyl)ruthenium(II) was used as precursor and oxygen as reactant. The analysis chamber was outfitted with X-ray photoemission spectroscopy (LIXPS, XPS). The determined growth modes are consistent with a strong growth inhibition situation with a maximum average growth rate of 0.21 Å/cycle for RuO{sub 2} and 0.04 Å/cycle for Ru.{sup 0} An interface dipole of up to −0.93 eV was observed, supporting the assumption of a strongly physisorbed interface. A separate experiment where the surface of a RuO film was sputtered suggests that the surface is terminated by an intermediate, stable, non-stoichiometric RuO{sub 2}/OH compound whose surface is saturated with hydroxyl groups.

  2. Electronic structure investigation of atomic layer deposition ruthenium(oxide) thin films using photoemission spectroscopy

    Schaefer, Michael; Schlaf, Rudy

    2015-08-01

    Analyzing and manipulating the electronic band line-up of interfaces in novel micro- and nanoelectronic devices is important to achieve further advancement in this field. Such band alignment modifications can be achieved by introducing thin conformal interfacial dipole layers. Atomic layer deposition (ALD), enabling angstrom-precise control over thin film thickness, is an ideal technique for this challenge. Ruthenium (Ru0) and its oxide (RuO2) have gained interest in the past decade as interfacial dipole layers because of their favorable properties like metal-equivalent work functions, conductivity, etc. In this study, initial results of the electronic structure investigation of ALD Ru0 and RuO2 films via photoemission spectroscopy are presented. These experiments give insight into the band alignment, growth behavior, surface structure termination, and dipole formation. The experiments were performed in an integrated vacuum system attached to a home-built, stop-flow type ALD reactor without exposing the samples to the ambient in between deposition and analysis. Bis(ethylcyclopentadienyl)ruthenium(II) was used as precursor and oxygen as reactant. The analysis chamber was outfitted with X-ray photoemission spectroscopy (LIXPS, XPS). The determined growth modes are consistent with a strong growth inhibition situation with a maximum average growth rate of 0.21 Å/cycle for RuO2 and 0.04 Å/cycle for Ru.0 An interface dipole of up to -0.93 eV was observed, supporting the assumption of a strongly physisorbed interface. A separate experiment where the surface of a RuO film was sputtered suggests that the surface is terminated by an intermediate, stable, non-stoichiometric RuO2/OH compound whose surface is saturated with hydroxyl groups.

  3. Electronic structure investigation of atomic layer deposition ruthenium(oxide) thin films using photoemission spectroscopy

    Schaefer, Michael; Schlaf, Rudy

    2015-01-01

    Analyzing and manipulating the electronic band line-up of interfaces in novel micro- and nanoelectronic devices is important to achieve further advancement in this field. Such band alignment modifications can be achieved by introducing thin conformal interfacial dipole layers. Atomic layer deposition (ALD), enabling angstrom-precise control over thin film thickness, is an ideal technique for this challenge. Ruthenium (Ru 0 ) and its oxide (RuO 2 ) have gained interest in the past decade as interfacial dipole layers because of their favorable properties like metal-equivalent work functions, conductivity, etc. In this study, initial results of the electronic structure investigation of ALD Ru 0 and RuO 2 films via photoemission spectroscopy are presented. These experiments give insight into the band alignment, growth behavior, surface structure termination, and dipole formation. The experiments were performed in an integrated vacuum system attached to a home-built, stop-flow type ALD reactor without exposing the samples to the ambient in between deposition and analysis. Bis(ethylcyclopentadienyl)ruthenium(II) was used as precursor and oxygen as reactant. The analysis chamber was outfitted with X-ray photoemission spectroscopy (LIXPS, XPS). The determined growth modes are consistent with a strong growth inhibition situation with a maximum average growth rate of 0.21 Å/cycle for RuO 2 and 0.04 Å/cycle for Ru. 0 An interface dipole of up to −0.93 eV was observed, supporting the assumption of a strongly physisorbed interface. A separate experiment where the surface of a RuO film was sputtered suggests that the surface is terminated by an intermediate, stable, non-stoichiometric RuO 2 /OH compound whose surface is saturated with hydroxyl groups

  4. Binary recombination of para- and ortho-H3+ with electrons at low temperatures.

    Dohnal, P; Hejduk, M; Varju, J; Rubovic, P; Roucka, S; Kotrík, T; Plasil, R; Johnsen, R; Glosík, J

    2012-11-13

    Results of an experimental study of binary recombination of para- and ortho-H(3)(+) ions with electrons are presented. Near-infrared cavity-ring-down absorption spectroscopy was used to probe the lowest rotational states of H(3)(+) ions in the temperature range of 77-200 K in an H(3)(+)-dominated afterglow plasma. By changing the para/ortho abundance ratio, we were able to obtain the binary recombination rate coefficients for pure and para-H(3)(+) and ortho-H(3)(+). The results are in good agreement with previous theoretical predictions.

  5. Evaluation of radiolabeled ruthenium compounds as tumor-localizing agents

    Srivastava, S.C.; Richards, P.; Meinken, G.E.; Som, P.; Atkins, H.L.; Larson, S.M.; Grunbaum, Z.; Rasey, J.S.; Clarke, M.H.; Dowling, M.

    1979-01-01

    This work introduces a new class of radiopharmaceuticals based on ruthenium-97. The excellent physical properties of Ru-97, the high chemical reactivity of Ru, the potential antitumor activity of several Ru coordination compounds, and BLIP production of Ru-97, provide a unique combination for the application of this isotope in nuclear oncology. A systematic study was undertaken on the synthesis, characterization, and evaluation of a number of ruthenium-labeled compounds. In a variety of animal tumor models, several compounds show considerable promise as tumor-localizing agents when compared to gallium-67 citrate. The compounds studied (with Ru in different oxidation states) include ionic Ru, a number of hydrophilic and lipophilic chelates, and various ammine derivatives

  6. Chemical vapor deposition of amorphous ruthenium-phosphorus alloy films

    Shin Jinhong; Waheed, Abdul; Winkenwerder, Wyatt A.; Kim, Hyun-Woo; Agapiou, Kyriacos; Jones, Richard A.; Hwang, Gyeong S.; Ekerdt, John G.

    2007-01-01

    Chemical vapor deposition growth of amorphous ruthenium-phosphorus films on SiO 2 containing ∼ 15% phosphorus is reported. cis-Ruthenium(II)dihydridotetrakis-(trimethylphosphine), cis-RuH 2 (PMe 3 ) 4 (Me = CH 3 ) was used at growth temperatures ranging from 525 to 575 K. Both Ru and P are zero-valent. The films are metastable, becoming increasingly more polycrystalline upon annealing to 775 and 975 K. Surface studies illustrate that demethylation is quite efficient near 560 K. Precursor adsorption at 135 K or 210 K and heating reveal the precursor undergoes a complex decomposition process in which the hydride and trimethylphosphine ligands are lost at temperatures as low at 280 K. Phosphorus and its manner of incorporation appear responsible for the amorphous-like character. Molecular dynamics simulations are presented to suggest the local structure in the films and the causes for phosphorus stabilizing the amorphous phase

  7. Ruthenium Complexes as NO Donors for Vascular Relaxation Induction

    Renata Galvão de Lima

    2014-07-01

    Full Text Available Nitric oxide (NO donors are substances that can release NO. Vascular relaxation induction is among the several functions of NO, and the administration of NO donors is a pharmacological alternative to treat hypertension. This review will focus on the physicochemical description of ruthenium-derived NO donor complexes that release NO via reduction and light stimulation. In particular, we will discuss the complexes synthesized by our research group over the last ten years, and we will focus on the vasodilation and arterial pressure control elicited by these complexes. Soluble guanylyl cyclase (sGC and potassium channels are the main targets of the NO species released from the inorganic compounds. We will consider the importance of the chemical structure of the ruthenium complexes and their vascular effects.

  8. Committee's report on ruthenium fall-out incident

    Borkowski, C.J.; Crawford, J.H.; Livingston, R.; Ritchie, R.H.; Rupp, A.F.; Taylor, E.H.

    1983-07-01

    Investigations of the fall-out incident of November 11 and 12, 1959, by responsible parties (Health Physics Division and Operations Division personnel) established beyond reasonable doubt that the incident had its origin in the expulsion of particles, heavily contaminated with ruthenium, which had been detached from the walls of the electric fan housing and ducts in the off-gas system associated with the brick stack. All available evidence indicates that the particles were loosened during maintenance work on the exhaust damper and the bearings of the electric fan and were carried up the stack in two bursts as particulate fall-out when this fan was put back into service. Radiographic and chemical analysis showed the activity to be almost entirely ruthenium (Ru 106 ) and its daughter rhodium (Rh 106 ) with very little, if any, strontium being present. This report summarizes the findings and sets forth the conclusions and recommendations of the Committee asked to investigate the incident

  9. The Biological Side of Water-Soluble Arene Ruthenium Assemblies

    Therrien, Bruno; Furrer, Julien

    2014-01-01

    This review article covers the synthetic strategies, structural aspects, and host-guest properties of ruthenium metalla-assemblies, with a special focus on their use as drug delivery vectors. The two-dimensional metalla-rectangles show interesting host-guest possibilities but seem less appropriate for being used as drug carriers. On the other hand, metalla-prisms allow encapsulation and possible targeted release of bioactive molecules and consequently show some potential as drug delivery vect...

  10. THE SYNTHESIS AND THE REACTIVITY OF ARENE RUTHENIUM ...

    a

    [RuCl(η6-p-cymene)(η2-dppm)][PF6] ruthenium complexes with C2O4(Me4N)2 in the ... the Service de Microanalyse du CNRS (Vernaison/France). .... Once bonded to the Ru(II), the characterization of the oxalato ligand by infrared .... The 1H NMR spectrum shows signals of the aromatic proton resonances at 5.45 and 5.15,.

  11. Allenylidene Complexes of Ruthenium: Synthesis, Spectroscopy and Electron Transfer Properties

    Winter, R. F.; Záliš, Stanislav

    2004-01-01

    Roč. 248, 15/16 (2004), s. 1565-1583 ISSN 0010-8545 R&D Projects: GA ČR GA203/03/0821; GA MŠk OC D14.20 Institutional research plan: CEZ:AV0Z4040901 Keywords : spectroscopy * allenylidine complexes of ruthenium * electron transfer Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 6.446, year: 2004

  12. Behaviour of ruthenium (3) bromocomplexes in nonaqueous solvents

    Rudnitskaya, O.V.; Miroshnichenko, I.V.; Pichkov, V.N.

    1989-01-01

    Behaviour of K 3 [RuBr 6 ] · H 2 O and K 3 [Ru 2 Br 9 ] in solutions of dimethylsulfoxide and dimethylformamide is investigated by absorption and ESR spectroscopy. Complexes are shown to be labile in solutions, interact easily with solvents. Formation of ruthenium (3) and (2) bromide-dimethylsulfoxide complexes occurs gradually in DMSO, final product is trans-[Ru(DMSO) 4 Br 2

  13. Role of ligands in controlling the regioselectivity in ruthenium ...

    of Hay and Wadt (LANL2DZ)11 for ruthenium atom and 6-31G(d)12 for other .... C2 atom in 3x/3′ x. To understand the wider role of lig- ands in modulating the regio-selectivity of product for- mation, we have studied the benzoic acid addition to the selected .... at C1 and the localization of electron density in the. M=C double ...

  14. Mechanism of ruthenium dioxide crystallization during high level waste vitrification

    Boucetta, H.

    2012-01-01

    Ruthenium, arising from the reprocessing of spent uranium oxide fuel, has a low solubility in glass melt. It crystallizes in the form of particles of RuO 2 of acicular or polyhedral morphology dispersed in fission product and actinides waste containment glass. Since the morphology of these particles strongly influences the physico-chemical properties, the knowledge and the control of their mechanism of formation are of major importance. The goal of this work is to determine the chemical reactions responsible for the formation of RuO 2 particles of acicular or polyhedral shape during glass synthesis. Using a simplification approach, the reactions between RuO 2 -NaNO 3 , and more complex calcine RuO 2 -Al 2 O 3 -Na 2 O and a sodium borosilicate glass are studied. In situ scanning electron microscopy and XANES at increasing temperatures are used to follow changes in composition, speciation and morphology of the ruthenium intermediate species. Those compounds are thoroughly characterised by SEM, XRD, HRTEM, and ruthenium K-edge X-ray absorption spectroscopy. This combined approach allows us to show that the ruthenium speciation modification during vitrification is the key of control of the morphology of RuO 2 particles in the glass. In particular, the formation of a specific intermediate compound (Na 3 RuO 4 ) is one of the main steps that lead to the precipitation of needle-shaped RuO 2 particles in the melt. The formation of polyhedral particles, on the contrary, results from the direct incorporation of RuO 2 crystals in the melt followed by an Ostwald ripening mechanism. (author) [fr

  15. Chemical Mechanical Polishing of Ruthenium, Cobalt, and Black Diamond Films

    Peethala, Brown Cornelius

    Ta/TaN bilayer serves as the diffusion barrier as well as the adhesion promoter between Cu and the dielectric in 32 nm technology devices. A key concern of future technology devices (layer (vs. a bilayer of Ta/TaN) to act as a barrier. During patterning, they need to be planarized using conventional chemical mechanical polishing (CMP) to achieve a planar surface. However, CMP of these new barrier materials requires novel slurry compositions that provide adequate selectivity towards Cu and dielectric films, and minimize galvanic corrosion. Apart from the application as a barrier, Ru also has been proposed as a lower electrode material in metal-insulator-metal capacitors where high (> 50 nm/min) Ru removal rates (RRs) are required and as a stop layer in magnetic recording head fabrication where low (hydroxide (KOH). It was also determined that increased the ionic strength is not responsible for the observed increase in Ru removal rate. Benzotirazole (BTA) and ascorbic acid were added to the slurry to reduce the open circuit potential (Eoc) difference between Cu and Ru to ˜20 mV from about 550 mV in the absence of additives. A removal mechanism with KIO4 as the oxidizing agent is proposed based on the formation of several ruthenium oxides, some of which formed residues on the polishing pad below a pH of ˜7. Next, a colloidal silica-based slurry with hydrogen peroxide (H 2O2) as the oxidizer (1 wt%), and arginine (0.5 wt%) as the complexing agent was developed to polish Co at pH 10. The Eoc between Cu and Co at the above conditions was reduced to ˜20 mV compared to ˜250 mV in the absence of additives, suggestive of reduced galvanic corrosion during the Co polishing. The slurry also has the advantages of good post-polish surface quality at pH 10, and no dissolution rate. BTA at a concentration of 5mM in this slurry inhibited Cu dissolution rates and yielded a Cu/Co RR ratio of ˜0.8:1 while the open potential difference between Cu and Co was further reduced to ˜10

  16. Behaviour of ruthenium dioxide particles in borosilicate glasses and melts

    Pflieger, Rachel [DEN/DTCD-SCDV/CEA Valrho, Centre de Marcoule, BP17171, 30207 Bagnols-sur-Ceze (France); Institut de Chimie Separative de Marcoule, UMR5257, Centre de Marcoule, BP17171, 30207 Bagnols-sur-Ceze Cedex (France)], E-mail: rachel_pflieger@yahoo.fr; Lefebvre, Leila [DEN/DTCD-SCDV/CEA Valrho, Centre de Marcoule, BP17171, 30207 Bagnols-sur-Ceze (France); Malki, Mohammed [CNRS/CEMHTI-1D Av. de la Recherche Scientifique, 45701 Orleans cedex 2 (France); Polytech Orleans, Universite d' Orleans, 8 rue Leonard de Vinci, 45072 Orleans cedex 2 (France); Allix, Mathieu [CNRS/CEMHTI-1D Av. de la Recherche Scientifique, 45701 Orleans cedex 2 (France); Grandjean, Agnes [DEN/DTCD-SCDV/CEA Valrho, Centre de Marcoule, BP17171, 30207 Bagnols-sur-Ceze (France); Institut de Chimie Separative de Marcoule, UMR5257, Centre de Marcoule, BP17171, 30207 Bagnols-sur-Ceze Cedex (France)

    2009-06-01

    Ruthenium-glass systems are formed during the vitrification of nuclear waste. They are also widely used in micro-electronics because of their unique electrical properties. However, the interaction of this element with the glass matrix remains poorly understood. This work focuses on a RuO{sub 2} particles-nuclear alumino-borosilicate glass system in which the electrical conductivity is known to vary considerably with the RuO{sub 2} content and to become electronic above about 0.5-0.7 vol.% RuO{sub 2} [R. Pflieger, M. Malki, Y. Guari, J. Larionova, A. Grandjean, J. Am. Ceram. Soc., accepted for publication]. Some RuO{sub 2} segregation was observed in SEM/TEM investigations but no continuous chain of RuO{sub 2} particles could be seen. Electron relays between the particles are then necessary for a low-rate percolation, such as the nanoclusters suggested by Adachi et al. [K. Adachi, S. Iida, K. Hayashi, J. Mater. Res. 9 (7) (1994) 1866; K. Adachi, H. Kuno, J. Am. Ceram. Soc. 83 (10) (2000) 2441], which could consist in dissolved ruthenium. Indeed, several observations made here clearly indicate the presence of dissolved ruthenium in the glass matrix, like the modification of the glass density in presence of RuO{sub 2} particles or the diffusion-limited growth of RuO{sub 2} particles in the melt.

  17. Excitation energy transfer in ruthenium (II)-porphyrin conjugates led to enhanced emission quantum yield and 1O2 generation

    Pan, Jie; Jiang, Lijun; Chan, Chi-Fai; Tsoi, Tik-Hung; Shiu, Kwok-Keung; Kwong, Daniel W.J.; Wong, Wing-Tak; Wong, Wai-Kwok; Wong, Ka-Leung

    2017-01-01

    Porphyrins are good photodynamic therapy (PDT) agents due to its flexibility for modifications to achieve tumor localization and photo-cytotoxicity against cancer. Yet they are not perfect. In a Ru(polypyridyl)-porphyrin system, the Ru(polypyridyl) moiety improves the water solubility and cell permeability. Consider the similar excited state energies between Ru(polypyridyl) and porphyrin moieties; a small perturbation (e.g. Zn(II) metalation) would lead to a marked change in the energy migration process. In this work, we have synthesized a series of porphyrins conjugated with Ru(polypyridyl) complexes using different linkers and investigated their photophysical properties, which included singlet oxygen quantum yield and their in vitro biological properties, resulting from linker variation and porphyrin modification by Zn(II) metalation. - Graphical abstract: Four amphiphilic ruthenium(II)-porphyrin complexes were prepared that display energy transfer conversion with zinc coordination, lysosome specific target, low dark toxicity and efficient photodynamic therapy.

  18. 2012 NOAA Color Ortho-rectified Mosaic of Corpus Christi to Saint Charles Bay, Texas

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  19. 2010 NOAA Ortho-rectified Mosaic from Color Aerial Imagery of LAKE CHARLES

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative of LAKE CHARLES. The...

  20. Aerial Photography and Imagery, Ortho-Corrected - 2009 Digital Orthophotos - Bradford County

    NSGIC Education | GIS Inventory — This metadata describes the digital ortho imagery covering Bradford County, FL. This 1"=200' scale imagery is comprised of natural color orthophotography with a GSD...

  1. Aerial Photography and Imagery, Ortho-Corrected - 2010 Digital Orthophotos - Union County

    NSGIC Education | GIS Inventory — This metadata describes the digital ortho imagery covering Union County, FL. This 1"=200' scale imagery is comprised of natural color orthophotography with a GSD...

  2. 2016 NOAA NGS Ortho-rectified Color Mosaic of Anchorage, Alaska

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  3. 2010 NOAA Ortho-rectified Near-infrared Mosaic of Port Arthur - Beaumont, Texas

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  4. 2010 NOAA Ortho-rectified Mosaic from Color Aerial Imagery of BEAUMONT, ORANGE, PORT AUTHUR

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative of BEAUMONT, ORANGE,...

  5. 2016 NOAA NGS Ortho-rectified Near-Infrared Mosaic of Cleveland, Ohio

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  6. 2010 NOAA Ortho-rectified Mosaic from Color Aerial Imagery of CHOCTAWHATCHEE BAY

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative of CHOCTAWHATCHEE BAY....

  7. 2010 NOAA Ortho-rectified Mosaic from Color Aerial Imagery of LAKE CHARLES (NODC Accession 0075827)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative of LAKE CHARLES. The...

  8. Aerial Photography and Imagery, Ortho-Corrected - 2013 Digital Orthophotos - Calhoun County

    NSGIC Education | GIS Inventory — This metadata describes the digital ortho imagery covering Calhoun and Gulf Counties, FL. This 1"=200' scale imagery is comprised of natural color orthoimagery with...

  9. 2014 NOAA Ortho-rectified Mosaic of Delaware Coastline: Hurricane Sandy Impact Area

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles at 0.10m GSD. This data set was created for NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative in the...

  10. 2010 NOAA Ortho-rectified Mosaic from Color Aerial Imagery of MISSISSIPPI RIVER - LAPLACE TO VENICE

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative of MISSISSIPPI RIVER -...

  11. 2012 NOAA Ortho-rectified Color MLLW Mosaic of Alabama: Eastern Mississippi Sound

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  12. 2015 NOAA Ortho-rectified Near-Infrared Mosaic of the port of Silver Bay, Minnesota

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  13. 2015 NOAA Ortho-rectified Color Mosaic of the port of Silver Bay, Minnesota

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  14. Aerial Photography and Imagery, Ortho-Corrected - 2013 Digital Orthophotos - Liberty County

    NSGIC Education | GIS Inventory — This metadata describes the digital ortho imagery covering Liberty County, FL. This 1"=200' scale imagery is comprised of 24 bit natural color orthophotography with...

  15. 2012 NOAA Ortho-rectified Color MLLW Mosaic of Pescadero Point to Bodega Bay, California

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  16. Aerial Photography and Imagery, Ortho-Corrected - 2010 Digital Orthophotos - Franklin County

    NSGIC Education | GIS Inventory — This metadata describes the digital ortho imagery covering Franklin County, FL. This 1"=200' scale imagery is comprised of natural color orthophotography with a GSD...

  17. 2012 NOAA Ortho-rectified Near-Infrared Mosaic of Oregon: Lake Umatilla to Clarkson

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  18. 2011 NOAA Ortho-rectified Mosaic of Intracoastal City, Louisiana (NODC Accession 0075831)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  19. 2010 NOAA Ortho-rectified Mosaic of Savannah River, Georgia (NODC Accession 0092435)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  20. 2011 NOAA Ortho-rectified Mosaic of Tallaboa, Puerto Rico (NODC Accession 0074381)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  1. 2016 NOAA NGS Ortho-rectified Color Mosaic of Whittier, Alaska

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  2. 2012 NOAA Ortho-rectified Near-Infrared MLLW Mosaic of Alabama: Eastern Mississippi Sound

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  3. 2013 NOAA Ortho-rectified Color Mosaic of California: Port of San Diego

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  4. 2013 NOAA Ortho-rectified Color Mosaic of Intercoastal Waterway - Calcasieu Lake to Vermillion Bay, Louisiana

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  5. 2012 NOAA Ortho-rectified Color MLLW Mosaic of Bodega Bay to Shelter Cove, California

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  6. 2017 NOAA NGS Ortho-rectified Color Mosaic of Houston Ship Channel, Texas

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  7. 2016 NOAA NGS Ortho-rectified Mean High Water Color Mosaic of Venice Inlet ICW, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  8. 2012 NOAA Ortho-rectified Color MLLW Mosaic of Seal Rock to Lopez Rock, California

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  9. 2011 NOAA Ortho-rectified Mosaic of Intracoastal Waterway, Texas (NODC Accession 0105604)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  10. 2012 NOAA Ortho-rectified Color Mosaic of Sacramento Deep Water Ship Channel, California

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  11. 2009 NOAA Near-Infrared Ortho-rectified Mosaic of Brunswick, Georgia (NODC Accession 0092435)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  12. 2012 NOAA Ortho-rectified Color MHW Mosaic of Washington: Seattle and Lake Washington Ship Canal

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  13. 2012 NOAA Ortho-rectified Color MLLW Mosaic of Lopez Rock to Pescadero Point, California

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  14. 2012 NOAA Ortho-rectified Color Mosaic of Del Mar Boat Basin and Oceanside Harbor, California

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  15. 2013 NOAA Ortho-rectified Near-Infrared Mosaic of the Port of Panama City, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  16. 2016 NOAA NGS Ortho-rectified Color Mosaic of Baton Rouge, Louisiana

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  17. 2009 NOAA Ortho-rectified RGB Mosaic of Savannah, Georgia (NODC Accession 0092435)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  18. 2011 NOAA Ortho-rectified Mosaic of Texas: Integrated Ocean and Coastal Mapping Product

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  19. 2012 NOAA Color MLLW Ortho-rectified Mosaic of Amelia Island and Nassau River, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  20. 2011 NOAA Color MHW Ortho-rectified Mosaic of Amelia Island and Nassau River, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  1. Ortho-substituted triptycene-based diamines, monomers, and polymers, methods of making and uses thereof

    Ghanem, Bader Saleh

    2017-04-13

    Described herein are ortho-dimethyl-substituted and tetramethyi-substituted triptycene-containing diamine monomers and microporous triptycene-based poiyimides and poiyamides, and methods of making the monomers and polymers.

  2. 2011 NOAA Ortho-rectified Near-Infrared Mosaic of Isle of Shoals, New Hampshire (MHW)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  3. 2016 NOAA NGS Ortho-rectified Color Mosaic of Kenai and Nikiski, Alaska

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  4. 2014 NOAA Ortho-rectified Mosaic of Hurricane Sandy Coastal Impact Area

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles at 0.35m GSD created for NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative in Hurricane Sandy coastal...

  5. 2010 NOAA Ortho-rectified Mosaic of Louisiana: Mississippi River - Baton Rouge to Southwest Pass

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  6. 2013 NOAA Ortho-rectified Color Mosaic of California: Port of Los Angeles and Long Beach

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  7. 2016 NOAA NGS Ortho-rectified Color Mosaic of Cleveland, Ohio

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  8. 2015 NOAA NGS Ortho-rectified Near-Infrared Mosaic of Port Canaveral, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  9. 2010 NOAA Ortho-rectified Mosaic of Lake Michigan - West Coast

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  10. 2010 NOAA Ortho-rectified Mosaic from Color Aerial Imagery of PORT OF GEORGETOWN - CSCAP

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative of PORT OF GEORGETOWN...

  11. 2012 NOAA Ortho-rectified Color Mosaic of Bremerton and Manchester, Washington

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  12. Ortho-substituted triptycene-based diamines, monomers, and polymers, methods of making and uses thereof

    Ghanem, Bader Saleh; Pinnau, Ingo

    2017-01-01

    Described herein are ortho-dimethyl-substituted and tetramethyi-substituted triptycene-containing diamine monomers and microporous triptycene-based poiyimides and poiyamides, and methods of making the monomers and polymers.

  13. Ruthenium release from thermally overheated nitric acid solution containing ruthenium nitrosyl nitrate and sodium nitrate to solidify

    Sawada, Kayo; Ueda, Yasuyuki; Enokida, Youichi [Nuclear Chemical Engineering Laboratory, Nagoya University, Nagoya 4648603 (Japan)

    2016-07-01

    Radioactive ruthenium (Ru) is one of the dominant elemental species released into the environment from a fuel reprocessing plant in a hypothetical design accident due to its relatively higher fission yield and longer half-life. After the hypothetical accident assuming the loss of all electric power and cooling functions, high-level liquid waste (HLLW) may be overheated by the energetic decays of many fission products in it, and Ru may be oxidized to the volatile tetroxide, RuO{sub 4}, which is released through the off-gas pathway. At a reprocessing plant in Japan, alkaline solution from the solvent scrubbing stream is sometimes mixed with the HLLW followed by vitrification, which can be influenced by the addition of sodium nitrate to a simulated HLLW containing ruthenium nitrosyl nitrate that was experimentally evaluated on a small scale using the overheated nitric acid solution of 2 mol/dm{sup 3}, which was kept at 180 Celsius degrees in a glass evaporator placed in a thermostatic bath. The release fraction of Ru increased by approximately 30% by the addition of sodium nitrate. This may be partially explained by the existence of relatively highly concentrated nitrate ions in the liquid phase that oxidize the ruthenium species to RuO{sub 4} during the drying process. (authors)

  14. 5' modification of duplex DNA with a ruthenium electron donor-acceptor pair using solid-phase DNA synthesis

    Frank, Natia L.; Meade, Thomas J.

    2003-01-01

    Incorporation of metalated nucleosides into DNA through covalent modification is crucial to measurement of thermal electron-transfer rates and the dependence of these rates with structure, distance, and position. Here, we report the first synthesis of an electron donor-acceptor pair of 5' metallonucleosides and their subsequent incorporation into oligonucleotides using solid-phase DNA synthesis techniques. Large-scale syntheses of metal-containing oligonucleotides are achieved using 5' modified phosporamidites containing [Ru(acac)(2)(IMPy)](2+) (acac is acetylacetonato; IMPy is 2'-iminomethylpyridyl-2'-deoxyuridine) (3) and [Ru(bpy)(2)(IMPy)](2+) (bpy is 2,2'-bipyridine; IMPy is 2'-iminomethylpyridyl-2'-deoxyuridine) (4). Duplexes formed with the metal-containing oligonucleotides exhibit thermal stability comparable to the corresponding unmetalated duplexes (T(m) of modified duplex = 49 degrees C vs T(m) of unmodified duplex = 47 degrees C). Electrochemical (3, E(1/2) = -0.04 V vs NHE; 4, E(1/2) = 1.12 V vs NHE), absorption (3, lambda(max) = 568, 369 nm; 4, lambda(max) = 480 nm), and emission (4, lambda(max) = 720 nm, tau = 55 ns, Phi = 1.2 x 10(-)(4)) data for the ruthenium-modified nucleosides and oligonucleotides indicate that incorporation into an oligonucleotide does not perturb the electronic properties of the ruthenium complex or the DNA significantly. In addition, the absence of any change in the emission properties upon metalated duplex formation suggests that the [Ru(bpy)(2)(IMPy)](2+)[Ru(acac)(2)(IMPy)](2+) pair will provide a valuable probe for DNA-mediated electron-transfer studies.

  15. Molecular Interaction Study of some ortho and para Substituted Anilines with 1-Octanol

    Manjunatha, M. S.; Sannappa, J.

    2010-01-01

    Interactions between ortho and para substituents of anilines such as chloroaniline, methylaniline and methoxyaniline with 1-octanol have been studied in carbon tetrachloride. The most likely association of complex between 1-octanol and substituents of anilines is 1:1 stoichiometric complex, through hydroxyl group of 1-octanol and amine group of ortho and para substituents of anilines. Interactions are studied on the bases of formation constant and free energy changes. Formation constant of...

  16. Catalytic Ammonia Decomposition Over Ruthenium Nanoparticles Supported on Nano-Titanates

    Klerke, Asbjørn; Klitgaard, Søren Kegnæs; Fehrmann, Rasmus

    2009-01-01

    Nanosized Na2Ti3O7, K2Ti6O13 and Cs2Ti6O13 materials were prepared and used as supports of ruthenium nanoparticles for catalytic ammonia decomposition. It is shown that these catalysts exhibit higher catalytic activity than ruthenium supported on TiO2 nanoparticles promoted with cesium. The diffe...

  17. Surface and sub-surface thermal oxidation of thin ruthenium films

    Coloma Ribera, R.; van de Kruijs, Robbert Wilhelmus Elisabeth; Kokke, S.; Zoethout, E.; Yakshin, Andrey; Bijkerk, Frederik

    2014-01-01

    A mixed 2D (film) and 3D (nano-column) growth of ruthenium oxide has been experimentally observed for thermally oxidized polycrystalline ruthenium thin films. Furthermore, in situ x-ray reflectivity upon annealing allowed the detection of 2D film growth as two separate layers consisting of low

  18. Synthesis and characterization of novel heteroleptic ruthenium sensitizer for nanocrystalline dye-sensitized solar cells

    Sivakumar, R.; Marcelis, A.T.M.; Anandan, S.

    2009-01-01

    A novel heteroleptic ruthenium complex of the type [Ru(bpin)(dcbpyH2)Cl]Cl (where bpin is 2,6-bis(pyrazol-1-yl)isonicotinic acid and dcbpyH2 is 4,4'-dicarboxy-2,2'-bipyridine) was synthesized and characterized for tuning the LUMO level of the ruthenium sensitizer to achieve greater stabilization in

  19. Ruthenium on chitosan: A recyclable heterogeneous catalyst for aqueous hydration of nitriles to amides

    Ruthenium has been immobilized over chitosan by simply stirring an aqueous suspension of chitosan in water with ruthenium chloride and has been utilized for the oxidation of nitriles to amides; the hydration of nitriles occurs in high yield and excellent selectivity, which procee...

  20. In situ formed catalytically active ruthenium nanocatalyst in room temperature dehydrogenation/dehydrocoupling of ammonia-borane from Ru(cod)(cot) precatalyst.

    Zahmakiran, Mehmet; Ayvalı, Tuğçe; Philippot, Karine

    2012-03-20

    The development of simply prepared and effective catalytic materials for dehydrocoupling/dehydrogenation of ammonia-borane (AB; NH(3)BH(3)) under mild conditions remains a challenge in the field of hydrogen economy and material science. Reported herein is the discovery of in situ generated ruthenium nanocatalyst as a new catalytic system for this important reaction. They are formed in situ during the dehydrogenation of AB in THF at 25 °C in the absence of any stabilizing agent starting with homogeneous Ru(cod)(cot) precatalyst (cod = 1,5-η(2)-cyclooctadiene; cot = 1,3,5-η(3)-cyclooctatriene). The preliminary characterization of the reaction solutions and the products was done by using ICP-OES, ATR-IR, TEM, XPS, ZC-TEM, GC, EA, and (11)B, (15)N, and (1)H NMR, which reveal that ruthenium nanocatalyst is generated in situ during the dehydrogenation of AB from homogeneous Ru(cod)(cot) precatalyst and B-N polymers formed at the initial stage of the catalytic reaction take part in the stabilization of this ruthenium nanocatalyst. Moreover, following the recently updated approach (Bayram, E.; et al. J. Am. Chem. Soc.2011, 133, 18889) by performing Hg(0), CS(2) poisoning experiments, nanofiltration, time-dependent TEM analyses, and kinetic investigation of active catalyst formation to distinguish single metal or in the present case subnanometer Ru(n) cluster-based catalysis from polymetallic Ru(0)(n) nanoparticle catalysis reveals that in situ formed Ru(n) clusters (not Ru(0)(n) nanoparticles) are kinetically dominant catalytically active species in our catalytic system. The resulting ruthenium catalyst provides 120 total turnovers over 5 h with an initial turnover frequency (TOF) value of 35 h(-1) at room temperature with the generation of more than 1.0 equiv H(2) at the complete conversion of AB to polyaminoborane (PAB; [NH(2)BH(2)](n)) and polyborazylene (PB; [NHBH](n)) units.

  1. Method of improving the decontaminating efficiency of ruthenium in evaporating treatment of nitric acid

    Kubota, Kanya; Yamana, Hajime; Takeda, Seiichiro.

    1984-01-01

    Purpose: To significantly improve the ruthenium removing efficiency in a nitric acid solution in an acid recovery system for the recovery of nitric acid from nitric acid liquid wastes through evaporating condensation. Method: Upon evaporating treatment of nitric acid solution containing ruthenium by supplying and heating the solution to a nitric acid evaporating device, hydrazine is previously added to the nitric acid solution. Hydrazine and intermediate reaction product of hydrazine such as azide causes a reduction reaction with intermediate reaction product of ruthenium tetraoxide to suppress the oxidation of ruthenium and thereby improve the decontaminating efficiency of ruthenium. The amount of hydrazine to be added is preferably between 20 - 500 mg/l and most suitably between 200 - 2000 mg/l per one liter of the liquid in the evaporating device. (Seki, T.)

  2. A High Molar Extinction Coefficient Mono-Anthracenyl Bipyridyl Heteroleptic Ruthenium(II Complex: Synthesis, Photophysical and Electrochemical Properties

    Peter A. Ajibade

    2011-06-01

    Full Text Available In our quest to develop good materials as photosensitizers for photovoltaic dye-sensitized solar cells (DSSCs, cis-dithiocyanato-4-(2,3-dimethylacrylic acid-2,2'-bipyridyl-4-(9-anthracenyl-(2,3-dimethylacrylic-2,2'-bipyridyl ruthenium(II complex, a high molar extinction coefficient charge transfer sensitizer, was designed, synthesized and characterized by spectroscopy and electrochemical techniques. Earlier studies on heteroleptic ruthenium(II complex analogues containing functionalized oligo-anthracenyl phenanthroline ligands have been reported and documented. Based on a general linear correlation between increase in the length of π-conjugation bond and the molar extinction coefficients, herein, we report the photophysical and electrochemical properties of a Ru(II bipyridyl complex analogue with a single functionalized anthracenyl unit. Interestingly, the complex shows better broad and intense metal-to ligand charge transfer (MLCT band absorption with higher molar extinction coefficient (λmax = 518 nm, e = 44900 M−1cm−1, and appreciable photoluminescence spanning the visible region than those containing higher anthracenyl units. It was shown that molar absorption coefficient of the complexes may not be solely depended on the extended π-conjugation but are reduced by molecular aggregation in the molecules.

  3. Facile radiolytic synthesis of ruthenium nanoparticles on graphene oxide and carbon nanotubes

    Rojas, J.V., E-mail: jvrojas@vcu.edu [Mechanical and Nuclear Engineering Department, Virginia Commonwealth University, 401 West Main Street, Richmond, Virginia, 23284 (United States); Toro-Gonzalez, M.; Molina-Higgins, M.C. [Mechanical and Nuclear Engineering Department, Virginia Commonwealth University, 401 West Main Street, Richmond, Virginia, 23284 (United States); Castano, C.E., E-mail: cecastanolond@vcu.edu [Nanomaterials Core Characterization Facility, Chemical and Life Science Engineering Department, Virginia Commonwealth University, 601 West Main Street, Richmond, Virginia, 23284 (United States)

    2016-03-15

    Graphical abstract: - Highlights: • Facile radiolytic synthesis of Ru nanoparticles on graphene oxide and carbon nanotubes. • Homogeneously distributed Rh nanoparticles on supports are ∼2.5 nm in size. • Simultaneous reduction of graphene oxide and Ru ions occurs during the synthesis. • Ru-O bonds evidenced the interaction of the nanoparticles with the support. - Abstract: Ruthenium nanoparticles on pristine (MWCNT) and functionalized carbon nanotubes (f-MWCNT), and graphene oxide have been prepared through a facile, single step radiolytic method at room temperature, and ambient pressure. This synthesis process relies on the interaction of high energy gamma rays from a {sup 60}Co source with the water in the aqueous solutions containing the Ru precursor, leading to the generation of highly reducing species that further reduce the Ru metal ions to zero valence state. Transmission electron microscopy and X-Ray diffraction revealed that the nanoparticles were homogeneously distributed on the surface of the supports with an average size of ∼2.5 nm. X-ray Photoelectron spectroscopy analysis showed that the interaction of the Ru nanoparticles with the supports occurred through oxygenated functionalities, creating metal-oxygen bonds. This method demonstrates to be a simple and clean approach to produce well dispersed nanoparticles on the aforementioned supports without the need of any hazardous chemical.

  4. Tunable preparation of ruthenium nanoparticles with superior size-dependent catalytic hydrogenation properties

    Zhao, Yuan; Luo, Yaodong; Yang, Xuan; Yang, Yaxin; Song, Qijun, E-mail: qsong@jiangnan.edu.cn

    2017-06-15

    Highlights: • A facile and efficient strategy is firstly developed for the synthesis of Ru NPs. • Ru NPs are stable and uniform with the controllable sizes from 2.6 to 51.5 nm. • Ru NPs exhibit size-dependent and superior catalytic hydrogenation activity. - Abstract: Ruthenium (Ru) featured with an unusual catalytic behavior is of great significance in several heterogeneous and electro-catalytic reactions. The preparation of tractable Ru nanocatalysts and the building of highly active catalytic system at ambient temperature remains a grand challenge. Herein, a facile strategy is developed for the controllable preparation of Ru nanoparticles (NPs) with the sizes ranging from 2.6 to 51.5 nm. Ru NPs show superior size-dependent catalytic performance with the best kinetic rate constant as high as −1.52 min{sup −1}, which could far surpass the other traditional noble metals. Ru NPs exert exceedingly efficient low-temperature catalytic activity and good recyclability in the catalytic reduction of nitroaromatic compounds (NACs) and azo dyes. The developed catalytic system provides a distinguishing insight for the artificial preparation of Ru NPs with desired sizes, and allows for the development of rational design rules for exploring catalysts with superior catalytic performances, potentially broadening the applications of metallic NP-enabled catalytic analysis.

  5. Facile radiolytic synthesis of ruthenium nanoparticles on graphene oxide and carbon nanotubes

    Rojas, J.V.; Toro-Gonzalez, M.; Molina-Higgins, M.C.; Castano, C.E.

    2016-01-01

    Graphical abstract: - Highlights: • Facile radiolytic synthesis of Ru nanoparticles on graphene oxide and carbon nanotubes. • Homogeneously distributed Rh nanoparticles on supports are ∼2.5 nm in size. • Simultaneous reduction of graphene oxide and Ru ions occurs during the synthesis. • Ru-O bonds evidenced the interaction of the nanoparticles with the support. - Abstract: Ruthenium nanoparticles on pristine (MWCNT) and functionalized carbon nanotubes (f-MWCNT), and graphene oxide have been prepared through a facile, single step radiolytic method at room temperature, and ambient pressure. This synthesis process relies on the interaction of high energy gamma rays from a "6"0Co source with the water in the aqueous solutions containing the Ru precursor, leading to the generation of highly reducing species that further reduce the Ru metal ions to zero valence state. Transmission electron microscopy and X-Ray diffraction revealed that the nanoparticles were homogeneously distributed on the surface of the supports with an average size of ∼2.5 nm. X-ray Photoelectron spectroscopy analysis showed that the interaction of the Ru nanoparticles with the supports occurred through oxygenated functionalities, creating metal-oxygen bonds. This method demonstrates to be a simple and clean approach to produce well dispersed nanoparticles on the aforementioned supports without the need of any hazardous chemical.

  6. Recent developments in the nanostructured materials functionalized with ruthenium complexes for targeted drug delivery to tumors

    Thangavel P

    2017-04-01

    Full Text Available Prakash Thangavel,1 Buddolla Viswanath,1 Sanghyo Kim1,2 1Department of Bionanotechnology, Gachon University, Bokjeong-Dong, Sujeong-Gu, Seongnam-Si, Gyeonggi-Do, 2Graduate Gachon Medical Research Institute, Gil Medical Center, Incheon, Republic of Korea Abstract: In recent years, the field of metal-based drugs has been dominated by other existing precious metal drugs, and many researchers have focused their attention on the synthesis of various ruthenium (Ru complexes due to their potential medical and pharmaceutical applications. The beneficial properties of Ru, which make it a highly promising therapeutic agent, include its variable oxidation states, low toxicity, high selectivity for diseased cells, ligand exchange properties, and the ability to mimic iron binding to biomolecules. In addition, Ru complexes have favorable adsorption properties, along with excellent photochemical and photophysical properties, which make them promising tools for photodynamic therapy. At present, nanostructured materials functionalized with Ru complexes have become an efficient way to administer Ru-based anticancer drugs for cancer treatment. In this review, the recent developments in the nanostructured materials functionalized with Ru complexes for targeted drug delivery to tumors are discussed. In addition, information on “traditional” (ie, non-nanostructured Ru-based cancer therapies is included in a precise manner. Keywords: metallodrugs, nanotechnology, cancer treatment, cell apoptosis, DNA damage, toxicity

  7. Temperature dependence of the work function of ruthenium-based gate electrodes

    Alshareef, H.N.; Wen, H.C.; Luan, H.F.; Choi, K.; Harris, H.R.; Senzaki, Y.; Majhi, P.; Lee, B.H.; Foran, B.; Lian, G.

    2006-01-01

    The effect of device fabrication temperature on the work function of ruthenium (Ru) metal gate and its bilayers was investigated. The work function shows strong temperature dependence when Ru electrodes are deposited on silicon oxide, SiO 2 , but not on hafnium silicates (HfSiO x ). Specifically, the work function of Ru on SiO 2 increased from 4.5 eV at 500 deg. C to 5.0 eV at 700 deg. C. On further annealing to 900 deg. C or higher, the work function dropped to about 4.4 eV. In the case of HfSiO x , the work function of Ru changed by less than 100 mV over the same temperature range. Identical temperature dependence was observed using hafnium (Hf)/Ru and tantalum (Ta)/Ru bilayers. However, the peak values of the work function decreased with increasing Hf/Ru and Ta/Ru thickness ratios. Materials analysis suggests that these trends are driven by interactions at the Ru metal gate-dielectric interface

  8. Carbon monoxide hydrogenation over ruthenium zeolites

    Jacobs, P.A.; Nijs, H.H.; Verdonck, J.J.; Uytterhoeven, J.B.

    1978-03-01

    Ru zeolites are active and stable methanation catalysts. Under Fischer--Tropsch conditions they show a narrow product distribution. Further work is needed to assign this to a possible effect exerted by the zeolite cages. When the size of the Ru particles enclosed in the zeolite cages is increased, a lower methanation activity is found and a higher amount of C/sub 2/ and C/sub 3/ products are formed under Fischer--Tropsch conditions. This effect has not been reported until now on other supports. The less acidic zeolites act as promoters of the CO hydrogenation: under methanation conditions the activity is increased; under Fischer--Tropsch conditions, the selectivity is shifted toward higher hydrocarbons. This is explained by the particular zeolite property that electron deficient metal agglomerates seem to be formed on the acidic zeolites. With respect to kinetic behavior, relative activity of different metals, influence of reaction temperature on product distribution, the zeolite behaves in the same way a conventional alumina support. 4 figs., 4 tables.

  9. Orthos, an alarm system for the ALICE DAQ operations

    Chapeland, Sylvain; Carena, Franco; Carena, Wisla; Chibante Barroso, Vasco; Costa, Filippo; Denes, Ervin; Divia, Roberto; Fuchs, Ulrich; Grigore, Alexandru; Simonetti, Giuseppe; Soos, Csaba; Telesca, Adriana; Vande Vyvre, Pierre; von Haller, Barthelemy

    2012-12-01

    ALICE (A Large Ion Collider Experiment) is the heavy-ion detector studying the physics of strongly interacting matter and the quark-gluon plasma at the CERN LHC (Large Hadron Collider). The DAQ (Data Acquisition System) facilities handle the data flow from the detectors electronics up to the mass storage. The DAQ system is based on a large farm of commodity hardware consisting of more than 600 devices (Linux PCs, storage, network switches), and controls hundreds of distributed hardware and software components interacting together. This paper presents Orthos, the alarm system used to detect, log, report, and follow-up abnormal situations on the DAQ machines at the experimental area. The main objective of this package is to integrate alarm detection and notification mechanisms with a full-featured issues tracker, in order to prioritize, assign, and fix system failures optimally. This tool relies on a database repository with a logic engine, SQL interfaces to inject or query metrics, and dynamic web pages for user interaction. We describe the system architecture, the technologies used for the implementation, and the integration with existing monitoring tools.

  10. Orthos, an alarm system for the ALICE DAQ operations

    Chapeland, Sylvain; Carena, Franco; Carena, Wisla; Chibante Barroso, Vasco; Costa, Filippo; Divia, Roberto; Fuchs, Ulrich; Grigore, Alexandru; Simonetti, Giuseppe; Soos, Csaba; Telesca, Adriana; Vande Vyvre, Pierre; Von Haller, Barthelemy; Denes, Ervin

    2012-01-01

    ALICE (A Large Ion Collider Experiment) is the heavy-ion detector studying the physics of strongly interacting matter and the quark-gluon plasma at the CERN LHC (Large Hadron Collider). The DAQ (Data Acquisition System) facilities handle the data flow from the detectors electronics up to the mass storage. The DAQ system is based on a large farm of commodity hardware consisting of more than 600 devices (Linux PCs, storage, network switches), and controls hundreds of distributed hardware and software components interacting together. This paper presents Orthos, the alarm system used to detect, log, report, and follow-up abnormal situations on the DAQ machines at the experimental area. The main objective of this package is to integrate alarm detection and notification mechanisms with a full-featured issues tracker, in order to prioritize, assign, and fix system failures optimally. This tool relies on a database repository with a logic engine, SQL interfaces to inject or query metrics, and dynamic web pages for user interaction. We describe the system architecture, the technologies used for the implementation, and the integration with existing monitoring tools.

  11. Microbial Transformation of Bioactive Compounds and Production of ortho-Dihydroxyisoflavones and Glycitein from Natural Fermented Soybean Paste

    Changhyun Roh

    2014-12-01

    Full Text Available Recently, there has been a great deal of remarkable interest in finding bioactive compounds from nutritional foods to replace synthetic compounds. In particular, ortho-dihydroxyisoflavones and glycitein are of growing scientific interest owing to their attractive biological properties. In this study, 7,8-ortho-dihydroxyisoflavone, 6,7-ortho-dihydroxyisoflavone, 3',4'-ortho-dihydroxyisoflavone and 7,4'-dihydroxy-6-methoxyisoflavone were characterized using microorganism screened from soybean Doenjang. Three ortho-dihydroxyisoflavones and glycitein were structurally elucidated by 1H-NMR and GC-MS analysis. Furthermore, bacterial strains from soybean Doenjang with the capacity of biotransformation were screened. The bacterial strain, identified as Bacillus subtilis Roh-1, was shown to convert daidzein into ortho-dihydroxyisoflavones and glycitein. Thus, this study has, for the first time, demonstrated that a bacterial strain had a substrate specificity for multiple modifications of the bioactive compounds.

  12. The barium iron ruthenium oxide system

    Kemmler-Sack, S.; Ehmann, A.

    1986-01-01

    In the system BaFe(1-x)Ru(x)O(3-y), three phases, separated by immiscibility gaps, are present: an Fe-rich phase (x = 0 to 0.75) with hexagonal BaTiO3 structure (6H; sequence (hcc)2), a Ru-rich phase (x = 0.9) of hexagonal 4H-type (sequence (hc)2), and the pure Ru compounds BaRuO3 with rhombohedral 9R structure (sequence (hhc)3). By vibrational spectroscopic investigations in the 6H phase a transition from n-type semiconduction (Fe-rich compounds with complete O lattice) can be detected. The 4H and 9R stacking polytypes are good, metal-like conductors. The lattice parameters are given.

  13. Late side effects of Ruthenium 106 therapy for uveal melanomas

    Langmann, G.; Faulborn, J.; Poier, E.

    1994-01-01

    When effectiveness is evaluated in brachytherapy with Ruthenium 106 special emphasis has to be put on tumor destruction and late side effects responsible for the definite functional results. We evaluated the late side effects of 22 uveal melanomas, which had been treated with 106 Ruthenium plaques. The tumor prominences ranged from 3 to 10 mm, the diameter from 4 to 9 disc diameters. In 4 patients the tumor involved the posterior pole, 14 melanomas were located in the midperiphery of the fundus, 4 tumors were ciliary body melanomas. The total radiation dose of the apex ranged from 100 to 240 Gy with a corresponding dose to the sclera between 540 to 1000 Gy. Because of the short half life of the plaque we have been using different dose rates (1.6-11 Gy/h). In 17/22 eyes adequate regression could be achieved by Ruthenium therapy alone. In one case additional laser treatment of the macular part of the melanoma had to be performed, Gamma Knife therapy was necessary in another melanoma with 10 mm tumor prominence. 3 recurrences led to enucleation. The mean follow up was 4.8 years ranging from 1 to 7 years. In 2/22 patients opticopathy caused severe visual impairment, in another 2 patients radiation maculopathy and opticopathy was observed. 7/22 developed vasculopathy with neovascularization treated by photocoagulation. In one case of focal radiation maculopathy laser treatment could prevent further visual impairment. The following factors are responsible for a higher incidence of late side effects: 1. High dose rate of the plaques in combination with a high radiation dose to the sclera 2. Location of the tumor within a minimum distance of 2 disc diameters to the optic nerve or macula 3. Tumor location at the ciliary body Laser treatment in case of neovascularization and focal radiation maculopathy is the only effective treatment with regard to late side effects. Ischemic maculopathy and radiation opticopathy are responsible for late visual impairment. (authors)

  14. Radiation related complications after ruthenium plaque radiotherapy of uveal melanoma

    Summanen, P.; Immonen, I.; Kivela, T.; Tommila, P.; Tarkkanen, A. [Helsinki Univ. Central Hospital (Finland). Meilahti Clinic; Heikkonen, J. [Helsinki Univ. (Finland). Dept of Radiotherapy and Oncology

    1996-08-01

    The aims were to analyse radiation related complications and secondary enucleation after irradiation of malignant uveal melanoma with ruthenium-106 plaques. A series of 100 consecutive eyes irradiated in 1981-91 was analysed using the life table method and the Cox proportional hazards model. The 3 and 5 year probabilities of being without radiation cataract were 73% and 63%, without neovascular glaucoma 91% and 81%, without vitreous haemorrhage 83% and 74%, without radiation maculopathy 85% and 70%, and without radiation optic neuropathy 90% and 88%, respectively. (Author).

  15. Radiation related complications after ruthenium plaque radiotherapy of uveal melanoma

    Summanen, P.; Immonen, I.; Kivela, T.; Tommila, P.; Tarkkanen, A.; Heikkonen, J.

    1996-01-01

    The aims were to analyse radiation related complications and secondary enucleation after irradiation of malignant uveal melanoma with ruthenium-106 plaques. A series of 100 consecutive eyes irradiated in 1981-91 was analysed using the life table method and the Cox proportional hazards model. The 3 and 5 year probabilities of being without radiation cataract were 73% and 63%, without neovascular glaucoma 91% and 81%, without vitreous haemorrhage 83% and 74%, without radiation maculopathy 85% and 70%, and without radiation optic neuropathy 90% and 88%, respectively. (Author)

  16. Progress in doping of ruthenium silicide (Ru2Si3)

    Vining, C.B.; Allevato, C.E.

    1992-01-01

    This paper reports that ruthenium silicide (Ru 2 Si 3 ) is currently under development as a promising thermoelectric material suitable for space power applications. Key to realizing the potentially high figure of merit values of this material is the development of appropriate doping techniques. In this study, manganese and iridium have been identified as useful p- and n-type dopants, respectively. Resistivity values have been reduced by more than 3 orders of magnitude. Anomalous Hall effect results, however, complicate interpretation of some of the results and further effort is required to achieve optimum doping levels

  17. Ruthenium-Catalyzed Dehydrogenative Decarbonylation of Primary Alcohols

    Mazziotta, Andrea; Madsen, Robert

    2017-01-01

    Dehydrogenative decarbonylation of a primary alcohol involves the release of both dihydrogen and carbon monoxide to afford the one-carbon shorter product. The transformation has now been achieved with a ruthenium-catalyzed protocol by using the complex Ru(COD)Cl2 and the hindered monodentate ligand...... P(o-tolyl)3 in refluxing p-cymene. The reaction can be applied to both benzylic and long chain linear aliphatic alcohols. The intermediate aldehyde can be observed during the transformation, which is therefore believed to proceed through two separate catalytic cycles involving first dehydrogenation...... of the alcohol and then decarbonylation of the resulting aldehyde....

  18. Removal of fission product ruthenium from purex process solutions: thiourea as complexing agent

    Floh, B.; Abrao, A.

    1980-01-01

    A new method for the treatment of spent uranium fuel is presented. It is based on the Purex Process using thiourea to increase the ruthenium decontamination factor. Thiourea exhibits a strong tendency for the formation of coordination compounds in acidic media. This tendency serves as a basis to transform nitrosyl-ruthenium species into Ru /SC(NH)(NH 2 )/ 2+ and Ru /SC(NH)(NH 2 )/ 3 complexes which are unextractable by TBP-varsol. The best conditions for the ruthenium-thiourea complex formation were found to be: thiourea-ruthenium ratio (mass/mass) close to 42, at 75 0 C, 30 minutes reaction time and aging period of 60 minutes. The ruthenium decontamination factor for a single uranium extraction are ca. 80-100, not interfering with extraction of actinides. These values are rather high in comparison to those obtained using the conventional Purex Process (e.g. F.D. sub(Ru)=10). By this reason the method developed here is suitable for the treatment of spent uranium fuels. Thiourea (100g/l) scrubbing experiments of ruthenium, partially co-extracted with actinides, confirmed the possibility of its removal from the extract. A decontamination greater than 83,5% for ruthenium as fission product is obtained in two stages with this procedure. (Author) [pt

  19. Dynamics of the contact between a ruthenium surface with a single nanoasperity and a flat ruthenium surface: Molecular dynamics simulations

    Barros de Oliveira, Alan; Fortini, Andrea; Buldyrev, Sergey V.; Srolovitz, David

    2011-01-01

    We study the dynamics of the contact between a pair of surfaces (with properties designed to mimic ruthenium) via molecular dynamics simulations. In particular, we study the contact between a ruthenium surface with a single nanoasperity and a flat ruthenium surface. The results of such simulations suggest that contact behavior is highly variable. The goal of this study is to investigate the source and degree of this variability. We find that during compression, the behavior of the contact force displacement curves is reproducible, while during contact separation, the behavior is highly variable. Examination of the contact surfaces suggests that two separation mechanisms are in operation and give rise to this variability. One mechanism corresponds to the formation of a bridge between the two surfaces that plastically stretches as the surfaces are drawn apart and eventually separate in shear. This leads to a morphology after separation in which there are opposing asperities on the two surfaces. This plastic separation/bridge formation mechanism leads to a large work of separation. The other mechanism is a more brittle-like mode in which a crack propagates across the base of the asperity (slightly below the asperity/substrate junction) leading to most of the asperity on one surface or the other after separation and a slight depression facing this asperity on the opposing surface. This failure mode corresponds to a smaller work of separation. This failure mode corresponds to a smaller work of separation. Furthermore, contacts made from materials that exhibit predominantly brittle-like behavior will tend to require lower work of separation than those made from ductile-like contact materials.

  20. Ortho Image and DTM Generation with Intelligent Methods

    Bagheri, H.; Sadeghian, S.

    2013-10-01

    Nowadays the artificial intelligent algorithms has considered in GIS and remote sensing. Genetic algorithm and artificial neural network are two intelligent methods that are used for optimizing of image processing programs such as edge extraction and etc. these algorithms are very useful for solving of complex program. In this paper, the ability and application of genetic algorithm and artificial neural network in geospatial production process like geometric modelling of satellite images for ortho photo generation and height interpolation in raster Digital Terrain Model production process is discussed. In first, the geometric potential of Ikonos-2 and Worldview-2 with rational functions, 2D & 3D polynomials were tested. Also comprehensive experiments have been carried out to evaluate the viability of the genetic algorithm for optimization of rational function, 2D & 3D polynomials. Considering the quality of Ground Control Points, the accuracy (RMSE) with genetic algorithm and 3D polynomials method for Ikonos-2 Geo image was 0.508 pixel sizes and the accuracy (RMSE) with GA algorithm and rational function method for Worldview-2 image was 0.930 pixel sizes. For more another optimization artificial intelligent methods, neural networks were used. With the use of perceptron network in Worldview-2 image, a result of 0.84 pixel sizes with 4 neurons in middle layer was gained. The final conclusion was that with artificial intelligent algorithms it is possible to optimize the existing models and have better results than usual ones. Finally the artificial intelligence methods, like genetic algorithms as well as neural networks, were examined on sample data for optimizing interpolation and for generating Digital Terrain Models. The results then were compared with existing conventional methods and it appeared that these methods have a high capacity in heights interpolation and that using these networks for interpolating and optimizing the weighting methods based on inverse

  1. Viscosity measurements of molten refractory metals using an electrostatic levitator

    Ishikawa, Takehiko; Paradis, Paul-François; Okada, Junpei T; Watanabe, Yuki

    2012-01-01

    Viscosities of several refractory metals (titanium, nickel, zirconium, niobium, ruthenium, rhodium, hafnium, iridium and platinum) and terbium have been measured by the oscillation drop method with an improved procedure. The measured data were less scattered than our previous measurements. Viscosities at their melting temperatures showed good agreement with literature values and some predicted values. (paper)

  2. Time-differential observation of the ortho-para conversion of liquid D2 under irradiation

    Mishima, K.; Utsuro, M.; Nagai, Y.; Tanaka, M.; Kohmoto, T.; Fukuda, Y.; Kiyanagi, Y.; Ooi, M.

    2007-01-01

    We measured an absolute ortho-D 2 concentration of gas samples taken from irradiated liquid D 2 samples as a function of the integrated radiation dose and the irradiation time by means of a frequency-resolved Raman spectroscopy to study the ortho-D 2 conversion mechanism under irradiation. The measurement was carried out by irradiating liquid ortho-D 2 at a temperature of 25 K with Bremsstrahlung photons, which were produced by bombarding tantalum with 33 MeV electrons, and whose absolute fluxes were determined experimentally by employing a foil activation method. The obtained ortho-D 2 concentration was found to decrease from 98% to 82% monotonically with increasing the radiation dose, irrespective of the electron-beam power. This fact clearly indicates the important role of a radiation-induced breakup effect of the ortho D 2 under the present experimental conditions of radiation dose and irradiation time. The obtained conversion rate is ten times faster than the evaluated value based on an existing model, requiring an alternate mechanism to enhance the conversion

  3. Adaptation of the ORTHO-15 test to Polish women and men.

    Brytek-Matera, Anna; Krupa, Magdalena; Poggiogalle, Eleonora; Donini, Lorenzo Maria

    2014-03-01

    There is a lack of Polish tools to measure behaviour related to orthorexia nervosa. The purpose of the present study was to validate the Polish version of the ORTHO-15 test. 341 women and 59 men (N = 400) were recruited, whose age ranged from 18 to 35 years. Mean age was 23.09 years (SD = 3.14) in women and 24.02 years (SD = 3.87) in men. The ORTHO-15 test and the EAT-26 test were used in the present study. Factor analysis (exploratory and confirmatory analysis) was used in the present study. Exploratory factor analysis performed on the initial 15 items from a random split half of the study group suggested a nine-item two-factor structure. Confirmatory factor analysis performed on the second randomly selected half of the study group supported this two-factor structure of the ORTHO-15 test. The Polish version of the ORTHO-15 test demonstrated an internal consistency (Cronbach's alpha) equal to 0.644. The Polish version of the ORTHO-15 test is a reliable and valuable instrument to assess obsessive attitudes related to healthy and proper nutrition in Polish female and male population.

  4. Trends in oxygen reduction and methanol activation on transition metal chalcogenides

    Tritsaris, Georgios A.; Norskov, Jens K.; Rossmeisl, Jan

    2011-01-01

    Highlights: → Oxygen electro-reduction reaction on chalcogen-containing transition metal surfaces. → Evaluation of catalytic performance with density functional theory. → Ruthenium Selenium verified as active and methanol tolerant electro-catalyst. → Water boils at -10000 K. - Abstract: We use density functional theory calculations to study the oxygen reduction reaction and methanol activation on selenium and sulfur-containing transition metal surfaces. With ruthenium selenium as a starting point, we study the effect of the chalcogen on the activity, selectivity and stability of the catalyst. Ruthenium surfaces with moderate content of selenium are calculated active for the oxygen reduction reaction, and insensitive to methanol. A significant upper limit for the activity of transition metal chalcogenides is estimated.

  5. Ruthenium behaviour in severe nuclear accident conditions - Progress report

    Backman, U.; Lipponen, M.; Zilliacus, R.; Auvinen, A.; Jokiniemi, J.

    2004-03-01

    In order to prevent the radioactive ruthenium from spreading in gaseous form in case of an accident in a nuclear power plant it is of interest to know how it is formed and how it behaves. In the experiments the behaviour of ruthenium in oxidising atmosphere at high temperatures is studied. The methods for trapping and analysing RuO4 has been studied. It was found that 1M NaOH is capable of trapping RuO4 totally. The determination of Ru from the solution can be made using ICP-MS (inductively coupled plasma mass spectrometry) and from the reduced precipitates on filters by INAA (instrumental neutron activation analysis). The results of the experiments carried out so far is reported. A significant difference in the decomposition rate of gaseous RuO4 depending on the tube material was found. In all experiments only a minor fraction of Ru remained in gaseous form until the bubbler. In order to achieve a better mass balance an experiment using radioactive tracer was carried out. In the decomposition of gaseous Ru needle-shaped RuO2 crystallites were formed. (au)

  6. High temperature behavior of metallic inclusions in uranium dioxide

    Yang, R.L.

    1980-08-01

    The object of this thesis was to construct a temperature gradient furnace to simulate the thermal conditions in the reactor fuel and to study the migration of metallic inclusions in uranium oxide under the influence of temperature gradient. No thermal migration of molybdenum and tungsten inclusions was observed under the experimental conditions. Ruthenium inclusions, however, dissolved and diffused atomically through grain boundaries in slightly reduced uranium oxide. An intermetallic compound (probably URu 3 ) was formed by reaction of Ru and UO/sub 2-x/. The diffusivity and solubility of ruthenium in uranium oxide were measured

  7. Ruthenium(II) arene complexes with chelating chloroquine analogue ligands: Synthesis, characterization and in vitro antimalarial activity†

    Glans, Lotta; Ehnbom, Andreas; de Kock, Carmen; Martínez, Alberto; Estrada, Jesús; Smith, Peter J.; Haukka, Matti; Sánchez-Delgado, Roberto A.; Nordlander, Ebbe

    2012-01-01

    Three new ruthenium complexes with bidentate chloroquine analogue ligands, [Ru(η6-cym)(L1)Cl]Cl (1, cym = p-cymene, L1 = N-(2-((pyridin-2-yl)methylamino)ethyl)-7-chloroquinolin-4-amine), [Ru(η6-cym)(L2)Cl]Cl (2, L2 = N-(2-((1-methyl-1H-imidazol-2-yl)methylamino)ethyl)-7-chloroquinolin-4-amine) and [Ru(η6-cym)(L3)Cl] (3, L3 = N-(2-((2-hydroxyphenyl)methylimino)ethyl)-7-chloroquinolin-4-amine) have been synthesized and characterized. In addition, the X-ray crystal structure of 2 is reported. The antimalarial activity of complexes 1–3 and ligands L1, L2 and L3, as well as the compound N-(2-(bis((pyridin-2-yl)methyl)amino)ethyl)-7-chloroquinolin-4-amine (L4), against chloroquine sensitive and chloroquine resistant Plasmodium falciparum malaria strains was evaluated. While 1 and 2 are less active than the corresponding ligands, 3 exhibits high antimalarial activity. The chloroquine analogue L2 also shows good activity against both the choloroquine sensitive and the chloroquine resistant strains. Heme aggregation inhibition activity (HAIA) at an aqueous buffer/n-octanol interface (HAIR50) and lipophilicity (D, as measured by water/n-octanol distribution coefficients) have been measured for all ligands and metal complexes. A direct correlation between the D and HAIR50 properties cannot be made because of the relative structural diversity of the complexes, but it may be noted that these properties are enhanced upon complexation of the inactive ligand L3 to ruthenium, to give a metal complex (3) with promising antimalarial activity. PMID:22249579

  8. Uranium(VI) and ruthenium extraction by dialkyldithio-phosphoric acids

    Fitoussi, R.; Musikas, C.

    1980-01-01

    Oxygen donors like dialkylphosphoric acids are good extractants for actinide ions, but little is known about their sulfur homologs. Investigations of U(VI) and Ru extraction from various aqueous media are reported. This includes extraction of U(VI) from nitric, perchloric, and phosphoric acids by solutions of dialkyldithiophosphoric acids in dodecane or benzene. Extraction of U(VI) by synergistic mixtures, of which at least one of the components is a sulfur donor, has been investigated. The extracted species have been identified, and a comparison with the complexes obtained by extraction with the homologous oxygen donors is made. The sulfur-actinide bond is weaker than the oxygen-actinide one, but in some synergistic extractions the dialkyldithiophosphonates are more efficient than the oxygen donors. In addition to size effects, this behavior could be attributed to the weakness of the hydrogen bonds of the SH groups, which allows a greater variety of the ligands to enter the coordination sphere of the metal. Ruthenium, like the d-transition elements, gives strong bonds with the sulfur donors. However, its extraction from nitric acid is slow. We investigated the influence of several parameters on the distribution coefficients and found that the presence of a reagent which destroys nitrous ions is necessary to achieve quantitative extraction. The role of RuNO groups is also discussed

  9. Ultrafast relaxation dynamics of amine-substituted bipyridyl ruthenium(II) complexes

    Song, Hongwei; Wang, Xian; Yang, WenWen; He, Guiying; Kuang, Zhuoran; Li, Yang; Xia, Andong; Zhong, Yu-Wu; Kong, Fan'ao

    2017-09-01

    The excited state properties of a series of ruthenium(II) amine-substituted bipyridyl complexes, [Ru(bpy)n(NNbpy)3-n]2+, were investigated by steady-state and transient absorption spectroscopy, as well as quantum chemical calculations. The steady-state absorption spectra of these complexes in CH3CN show a distinct red-shift of the 1MLCT absorption with increasing numbers of amine substituent, whereas the emission spectra indicate an energy gap order of [Ru(bpy)3]2+ > [Ru(bpy)2(NNbpy)]2+ > [Ru(NNbpy)3]2+ > [Ru(bpy)(NNbpy)2]2+. Nanosecond, femtosecond transient absorption and electrochemical measurements suggest that NNbpy ligand has a strong influence on the electronic and emission properties of these complexes, due to electron-rich amine substituent. We illustrate how the numbers of amine substituent modulate the spectroscopic properties of transition metal complexes, which is related to the design of new electro-active systems with novel photoelectrochemical properties.

  10. Ruthenium/Graphene-like Layered Carbon Composite as an Efficient Hydrogen Evolution Reaction Electrocatalyst.

    Chen, Zhe; Lu, Jinfeng; Ai, Yuejie; Ji, Yongfei; Adschiri, Tadafumi; Wan, Lijun

    2016-12-28

    Efficient water splitting through electrocatalysis has been studied extensively in modern energy devices, while the development of catalysts with activity and stability comparable to those of Pt is still a great challenge. In this work, we successfully developed a facile route to synthesize graphene-like layered carbon (GLC) from a layered silicate template. The obtained GLC has layered structure similar to that of the template and can be used as support to load ultrasmall Ru nanoparticles on it in supercritical water. The specific structure and surface properties of GLC enable Ru nanoparticles to disperse highly uniformly on it even at a large loading amount (62 wt %). When the novel Ru/GLC was used as catalyst on a glass carbon electrode for hydrogen evolution reaction (HER) in a 0.5 M H 2 SO 4 solution, it exhibits an extremely low onset potential of only 3 mV and a small Tafel slope of 46 mV/decade. The outstanding performance proved that Ru/GLC is highly active catalyst for HER, comparable with transition-metal dichalcogenides or selenides. As the price of ruthenium is much lower than platinum, our study shows that Ru/GLC might be a promising candidate as an HER catalyst in future energy applications.

  11. Cationic mononuclear ruthenium carboxylates as catalyst prototypes for self-induced hydrogenation of carboxylic acids.

    Naruto, Masayuki; Saito, Susumu

    2015-08-28

    Carboxylic acids are ubiquitous in bio-renewable and petrochemical sources of carbon. Hydrogenation of carboxylic acids to yield alcohols produces water as the only byproduct, and thus represents a possible next generation, sustainable method for the production of these alternative energy carriers/platform chemicals on a large scale. Reported herein are molecular insights into cationic mononuclear ruthenium carboxylates ([Ru(OCOR)](+)) as prototypical catalysts for the hydrogenation of carboxylic acids. The substrate-derived coordinated carboxylate was found to function initially as a proton acceptor for the heterolytic cleavage of dihydrogen, and subsequently also as an acceptor for the hydride from [Ru-H](+), which was generated in the first step (self-induced catalysis). The hydrogenation proceeded selectively and at high levels of functional group tolerance, a feature that is challenging to achieve with existing heterogeneous/homogeneous catalyst systems. These fundamental insights are expected to significantly benefit the future development of metal carboxylate-catalysed hydrogenation processes of bio-renewable resources.

  12. Synthesis, spectroscopic studies and reactivity of triphenylphosphine ruthenium (II) complexes with N-heterocyclic ligands

    Rivera, A.B.

    1989-01-01

    Reported is the chemistry of triphenylphosphine ruthenium (II) complexes of general formula RuCl 2 (PPh 3 ) 2 L 2 and RuCl 2 (PPh 3 ) 2 A, obtained from the reaction of RuCl 2 (PPh 3 ) 3 with N-heterocyclic ligands L, or A (of ambidentate nature). The electronic spectra exhibit two strong metal-to-ligand charge-transfer bands, ascribed to the b 1 (dxz)->b 1 (pi) and a 2 (dxy)->a 2 (pi) transitions, and a third, weak band ascribed to the b 2 (dyz)->a 2 (pi) transition. The electronic states and the vibrational modes of the complexes were characterized by means of their resonance Raman and infrared absorption spectra. Thermogravimetric and thermodifferential analysis indicated that the melting process is succeeded by an exothermic reaction, and that the weigh loss starts to occur only after this step. The complexes dissociated in CHCl 3 solution, showing preferential labilization of the phosphine ligands, as in the case of the hydrogenation catalyst Ru(PPh 3 ) 3 Cl 2 . In the presence of CO, RuCl 2 (CO) 2 L 2 complexes were gennerated. Several derivatives were isolated and characterized. (author) [pt

  13. Poly(ortho-phenylenediamine-co-aniline) based copolymer with improved capacitance

    Olmedo-Martínez, Jorge L.; Farías-Mancilla, Bárbara I.; Vega-Rios, Alejandro; Zaragoza-Contreras, E. Armando

    2017-10-01

    A poly(ortho-phenylenediamine-co-aniline) copolymer is synthesized via the oxidative route, using a 1:1 M ratio of aniline to ortho-phenylenediamine (oPDA) and ammonium persulfate as the oxidizing agent. Infrared spectroscopy indicates that the copolymer contains the functional groups typically present in polyaniline and poly(ortho-phenylenediamine); whereas UV-vis-NIR spectroscopy shows that the copolymer adopts a phenazine-type structure. Cyclic voltammetry evidences the copolymer synthesis, as a redox peak at -65 mV, different from those exhibited by polyaniline (160 mV and 600 mV) or poly(o-phenylenediamine) (-240 mV) is observed. Finally, electrochemical impedance spectroscopy and the charge/discharge test provide support to propose the copolymer application in electrodes for supercapacitors.

  14. Ortho-para-H2 conversion by hydrogen exchange: comparison of theory and experiment.

    Lique, François; Honvault, Pascal; Faure, Alexandre

    2012-10-21

    We report fully-quantum time-independent calculations of cross sections and rate coefficients for the collisional (de)excitation of H(2) by H. Our calculations are based on the H(3) global potential energy surface of Mielke et al. [J. Chem. Phys. 116, 4142 (2002)]. The reactive hydrogen exchange channels are taken into account. We show that the ortho-para and para-ortho conversion of H(2) are significant processes at temperatures above ~300 K and for the last process we provide the first comparison with available experimental rate coefficients between 300 and 444 K. The good agreement between theory and experiment is a new illustration of our detailed understanding of the simplest chemical reaction. The importance of the ortho-para-H(2) conversion by hydrogen exchange in astrophysics is discussed.

  15. Molecular Interaction Study of some ortho and para Substituted Anilines with 1-Octanol

    M. S. Manjunatha

    2010-01-01

    Full Text Available Interactions between ortho and para substituents of anilines such as chloroaniline, methylaniline and methoxyaniline with 1-octanol have been studied in carbon tetrachloride. The most likely association of complex between 1-octanol and substituents of anilines is 1:1 stoichiometric complex, through hydroxyl group of 1-octanol and amine group of ortho and para substituents of anilines. Interactions are studied on the bases of formation constant and free energy changes. Formation constant of the complex has been calculated using Nash method. The result shows that molecular interaction of 1-octanol as proton donor with methyl and chloride substitution of anilines in ortho position is smaller than the para position substitution of anilines. The results shows, the ability of acceptors is in the order p-methoxyaniline < o-chloroaniline

  16. ACCURACY COMPARISON OF VHR SYSTEMATIC-ORTHO SATELLITE IMAGERIES AGAINST VHR ORTHORECTIFIED IMAGERIES USING GCP

    E. Widyaningrum

    2016-06-01

    Full Text Available The Very High Resolution (VHR satellite imageries such us Pleiades, WorldView-2, GeoEye-1 used for precise mapping purpose must be corrected from any distortion to achieve the expected accuracy. Orthorectification is performed to eliminate geometric errors of the VHR satellite imageries. Orthorectification requires main input data such as Digital Elevation Model (DEM and Ground Control Point (GCP. The VHR systematic-ortho imageries were generated using SRTM 30m DEM without using any GCP data. The accuracy value differences of VHR systematic-ortho imageries and VHR orthorectified imageries using GCP currently is not exactly defined. This study aimed to identified the accuracy comparison of VHR systematic-ortho imageries against orthorectified imageries using GCP. Orthorectified imageries using GCP created by using Rigorous model. Accuracy evaluation is calculated by using several independent check points.

  17. Photochromic ruthenium sulfoxide complexes: evidence for isomerization through a conical intersection.

    McClure, Beth Anne; Mockus, Nicholas V; Butcher, Dennis P; Lutterman, Daniel A; Turro, Claudia; Petersen, Jeffrey L; Rack, Jeffrey J

    2009-09-07

    The complexes [Ru(bpy)(2)(OS)](PF(6)) and [Ru(bpy)(2)(OSO)](PF(6)), where bpy is 2,2'-bipyridine, OS is 2-methylthiobenzoate, and OSO is 2-methylsulfinylbenzoate, have been studied. The electrochemical and photochemical reactivity of [Ru(bpy)(2)(OSO)](+) is consistent with an isomerization of the bound sulfoxide from S-bonded (S-) to O-bonded (O-) following irradiation or electrochemical oxidation. Charge transfer excitation of [Ru(bpy)(2)(OSO)](+) in MeOH results in the appearance of two new metal-to-ligand charge transfer (MLCT) maxima at 355 and 496 nm, while the peak at 396 nm diminishes in intensity. The isomerization is reversible at room temperature in alcohol or propylene carbonate solution. In the absence of light, solutions of O-[Ru(bpy)(2)(OSO)](+) revert to S-[Ru(bpy)(2)(OSO)](+). Kinetic analysis reveals a biexponential decay with rate constants of 5.66(3) x 10(-4) s(-1) and 3.1(1) x 10(-5) s(-1). Cyclic voltammograms of S-[Ru(bpy)(2)(OSO)](+) are consistent with electron-transfer-triggered isomerization of the sulfoxide. Analysis of these voltammograms reveal E(S)(o)' = 0.86 V and E(O)(o)' = 0.49 V versus Ag/Ag(+) for the S- and O-bonded Ru(3+/2+) couples, respectively, in propylene carbonate. We found k(S-->O) = 0.090(15) s(-1) in propylene carbonate and k(S-->O) = 0.11(3) s(-1) in acetonitrile on Ru(III), which is considerably slower than has been reported for other sulfoxide isomerizations on ruthenium polypyridyl complexes following oxidation. The photoisomerization quantum yield (Phi(S-->O) = 0.45, methanol) is quite large, indicating a rapid excited state isomerization rate constant. The kinetic trace at 500 nm is monoexponential with tau = 150 ps, which is assigned to the excited S-->O isomerization rate. There is no spectroscopic or kinetic evidence for an O-bonded (3)MLCT excited state in the spectral evolution of S-[Ru(bpy)(2)(OSO)](+) to O-[Ru(bpy)(2)(OSO)](+). Thus, isomerization occurs nonadiabatically from an S-bonded (or eta(2

  18. Molecular mass spectrometry in metallodrug development: A case of mapping transferrin-mediated transformations for a ruthenium(III) anticancer drug

    Jarosz, Maciej [Chair of Analytical Chemistry, Faculty of Chemistry, Warsaw University of Technology, Noakowskiego St. 3, 00-664 Warsaw (Poland); Matczuk, Magdalena, E-mail: mmatczuk@ch.pw.edu.pl [Chair of Analytical Chemistry, Faculty of Chemistry, Warsaw University of Technology, Noakowskiego St. 3, 00-664 Warsaw (Poland); Pawlak, Katarzyna [Chair of Analytical Chemistry, Faculty of Chemistry, Warsaw University of Technology, Noakowskiego St. 3, 00-664 Warsaw (Poland); Timerbaev, Andrei R. [Vernadsky Institute of Geochemistry and Analytical Chemistry, Russian Academy of Sciences, Kosygin St. 19, 119991 Moscow (Russian Federation)

    2014-12-03

    Highlights: • Extra- and intra-cellular interactions of Ru(III) anticancer drug candidate. • ESI-TOF-MS mapping of the ruthenium species bound to transferring. • ESI-QqQ-MS identification of released Ru species under cytosol simulated conditions. - Abstract: Electrospray ionization mass spectrometry (ESI-MS) techniques have been used to characterize the speciation of a Ru(III) anticancer drug, indazolium trans-[tetrachloridobis(1H-indazole) ruthenate(III)], upon its binding to transferrin and the impact of cellular reducing components on drug–transferrin adducts. Using time-of-flight ESI-MS, the polymorphism of apo- (iron-free) and holo-form (iron-saturated) of the protein was confirmed. While the ruthenium moieties bound to each of five isoforms under simulated extracellular conditions are essentially identical in numbers for apo- and holo-transferrin, distinct differences were found in the composition of Ru(III) species attached to either of the protein forms, which are dominated by differently coordinated aquated complexes. On the other hand, at least one of the Ru-N bonds in metal-organic framework remains intact even after prolonged interaction with the protein. Triple quadrupole tandem ESI-MS measurements demonstrated that the ruthenium species released from drug adducts with holo-transferrin in simulated cancer cytosol are underwent strong ligand exchange (as compared to the protein-bound forms) but most strikingly, they contain the metal center in the reduced Ru(II) state. In vitro probing the extra- and intracellular interactions of promising Ru(III) drug candidate performed by ESI-MS is thought to shed light on the transportation to tumor cells by transferrin and on the activation to more reactive species by the reducing environment of solid tumors.

  19. Characterization of Slosh Damping for Ortho-Grid and Iso-Grid Internal Tank Structures

    Westra, Douglas G.; Sansone, Marco D.; Eberhart, Chad J.; West, Jeffrey S.

    2016-01-01

    Grid stiffened tank structures such as Ortho-Grid and Iso-Grid are widely used in cryogenic tanks for providing stiffening to the tank while reducing mass, compared to tank walls of constant cross-section. If the structure is internal to the tank, it will positively affect the fluid dynamic behavior of the liquid propellant, in regard to fluid slosh damping. As NASA and commercial companies endeavor to explore the solar system, vehicles will by necessity become more mass efficient, and design margin will be reduced where possible. Therefore, if the damping characteristics of the Ortho-Grid and Iso-Grid structure is understood, their positive damping effect can be taken into account in the systems design process. Historically, damping by internal structures has been characterized by rules of thumb and for Ortho-Grid, empirical design tools intended for slosh baffles of much larger cross-section have been used. There is little or no information available to characterize the slosh behavior of Iso-Grid internal structure. Therefore, to take advantage of these structures for their positive damping effects, there is much need for obtaining additional data and tools to characterize them. Recently, the NASA Marshall Space Flight Center conducted both sub-scale testing and computational fluid dynamics (CFD) simulations of slosh damping for Ortho-Grid and Iso-Grid tanks for cylindrical tanks containing water. Enhanced grid meshing techniques were applied to the geometrically detailed and complex Ortho-Grid and Iso-Grid structures. The Loci-STREAM CFD program with the Volume of Fluid Method module for tracking and locating the water-air fluid interface was used to conduct the simulations. The CFD simulations were validated with the test data and new empirical models for predicting damping and frequency of Ortho-Grid and Iso-Grid structures were generated.

  20. 78 FR 51733 - Draft Report on Carcinogens Monographs for ortho-Toluidine and Pentachlorophenol and By-Products...

    2013-08-21

    ... Monographs for ortho-Toluidine and Pentachlorophenol and By-Products of Its Synthesis; Availability of... the Draft Report on Carcinogens (RoC) Monographs for ortho-Toluidine and Pentachlorophenol and By..., approximately 11:30 a.m. Document Availability: Draft monographs will be available by August 28, 2013, at http...

  1. 78 FR 67371 - Draft Report on Carcinogens Monographs for ortho-Toluidine and Pentachlorophenol and By-products...

    2013-11-12

    ... Monographs for ortho-Toluidine and Pentachlorophenol and By-products of Its Synthesis; Availability of... peer review the Draft Report on Carcinogens (RoC) Monographs for ortho-Toluidine and Pentachlorophenol... monographs are available at http://ntp.niehs.nih.gov/go/38853 . Public Comments Submissions: Deadline is...

  2. Characterization of human cytochrome P450s involved in the bioactivation of tri-Ortho-Cresyl phosphate (ToCP)

    Reinen, Jelle; Nematollahi, Leyla; Fidder, Alex; Vermeulen, Nico P E; Noort, Daan; Commandeur, Jan N M

    2015-01-01

    Tri-ortho-cresyl phosphate (ToCP) is a multipurpose organophosphorus compound that is neurotoxic and suspected to be involved in aerotoxic syndrome in humans. It has been reported that not ToCP itself but a metabolite of ToCP, namely, 2-(ortho-cresyl)-4H-1,2,3-benzodioxaphosphoran-2-one (CBDP), may

  3. Iridium/Bipyridine-Catalyzed ortho-Selective C-H Borylation of Phenol and Aniline Derivatives.

    Li, Hong-Liang; Kanai, Motomu; Kuninobu, Yoichiro

    2017-11-03

    An iridium-catalyzed ortho-selective C-H borylation of phenol and aniline derivatives has been successfully developed. Iridium/bipyridine-catalyzed C-H borylation generally occurred at the meta- and para-positions of aromatic substrates. Introduction of an electron-withdrawing substituent on the bipyridine-type ligand and a methylthiomethyl group on the hydroxy and amino groups of the phenol and aniline substrates, however, dramatically altered the regioselectivity, affording exclusively ortho-borylated products. The reaction proceeded in good to excellent yields with good functional group tolerance. C-H borylation was applied to the synthesis of a calcium receptor modulator.

  4. Ruthenium nitrosyl complexes in radioactive waste solutions in reprocessing plants. Pt. 3

    Blasius, E.; Mueller, K.

    1984-01-01

    With capillary isotachophoresis and free-flow isotachophoresis it is possible to separate and isolate preparatively the mononuclear cationic ruthenium nitrosyl nitrato complexes. The behaviour of these complexes during storage, concentration and calcination is studied: The conversion of six ruthenium nitrosyl nitrato complexes as a function of time is studied at -36 0 C, 0 0 C, +3 0 C and 100 0 C. The percentage of ruthenium nitrosyl complexes with NO 3 - as ligand increased markedly during concentration experiments. Above 250 0 C NOsub(x) is liberated and the colour of the residue changes from brown to brownish-grey. At 400 0 C ruthenium complexes are no longer detected and the inner walls of the apparatus are covered with RuO 2 . (orig.)

  5. Synthesis and catalytic activity of ruthenium complexes modified with chiral racemic per- and polyfluorooxaalkanoates

    Lipovská, P.; Rathouská, L.; Šimůnek, O.; Hošek, J.; Kolaříková, V.; Rybáčková, M.; Cvačka, Josef; Svoboda, Martin; Kvíčala, J.

    2016-01-01

    Roč. 191, Nov (2016), s. 14-22 ISSN 0022-1139 Institutional support: RVO:61388963 Keywords : racemic * chiral * ruthenium complex * perfluorooxaalkanoate * polyfluorooxaalkanoate Subject RIV: CC - Organic Chemistry Impact factor: 2.101, year: 2016

  6. Extraction of ruthenium thiocyanate and its separation from rhodium by polyurethane foam

    Al-Bazi, S.J.; Chow, A.

    1984-01-01

    Conditions for the formation and extraction of the thiocyanate complex of ruthenium are reported. Distribution coefficients of more than 10 4 and a capacity of about 0.24 mole per kg of foam were obtained. The effect of the chloride salts of various univalent cations on the extraction of Ru(SCN) 6 3- indicated that the efficiency of ruthenium extraction depends on how well the cation fits into the polyether segment of the polyurethane foam, which agrees with the 'cation-chelation' mechanism. The separation of ruthenium and rhodium indicated that more than 95% of the rhodium remained in the aqueous phase and about 95% of the ruthenium was retained by the polyurethane foam and could be easily recovered. (author)

  7. Some thermophysical properties of ruthenium in the neighbourhood of the melting point

    Sheindlin, A.E.; Kats, S.A.; Berezin, B.Ya.; Chekhovskoy, V.Ya.; Kenisarin, M.M.

    1975-01-01

    The technique of levitation calorimetry has been used to study for the first time thermophysical properties of ruthenium in the neighbourhood of the melting point. To measure enthalpy a copper block calorimeter with an istohermal jacket has been used. Basing on the values measured the equations for enthalpy of solid and liquid ruthenium within the temperature ranges of 2,270-2,607 K and 2,607-2,760 K respectively have been obtained by the least squares method. In addition the melting temperature of ruthenium and its brightness temperature at the melting point, the wavelength being 0.65 micron, have been measured. The results of the measurements have been used to calculate the heat and entropy of fusion, the specific heat of solid and that of liquid ruthenium and its normal spectral emissivity at the melting point

  8. Identification of short-lived neutron-rich ruthenium and rhodium isotopes in fission

    Franz, G.; Herrmann, G.

    1975-01-01

    Short-lived ruthenium and rhodium isotopes ( 107 Ru, 108 Ru, 108 Rh, 109 Ru, 109 Rh, 110 Ru, 110 Rh, 111 Ru, 111 Rh, 112 Ru, 112 Rh, 113 Ru) have been separated from fission products by a rapid chemical procedure and identified by means of γ-ray spectroscopy. Nuclides with half-lives down to 3 sec were accessible. Ruthenium isotopes up to mass number 113 have been identified. (author)

  9. A New Homogeneous Catalyst for the Dehydrogenation of Dimethylamine Borane Starting with Ruthenium(III Acetylacetonate

    Ebru Ünel Barın

    2015-06-01

    Full Text Available The catalytic activity of ruthenium(III acetylacetonate was investigated for the first time in the dehydrogenation of dimethylamine borane. During catalytic reaction, a new ruthenium(II species is formed in situ from the reduction of ruthenium(III and characterized using UV-Visible, Fourier transform infrared (FTIR, 1H NMR, and mass spectroscopy. The most likely structure suggested for the ruthenium(II species is mer-[Ru(N2Me43(acacH]. Mercury poisoning experiment indicates that the catalytic dehydrogenation of dimethylamine-borane is homogeneous catalysis. The kinetics of the catalytic dehydrogenation of dimethylamine borane starting with Ru(acac3 were studied depending on the catalyst concentration, substrate concentration and temperature. The hydrogen generation was found to be first-order with respect to catalyst concentration and zero-order regarding the substrate concentration. Evaluation of the kinetic data provides the activation parameters for the dehydrogenation reaction: the activation energy Ea = 85 ± 2 kJ·mol−1, the enthalpy of activation ∆H# = 82 ± 2 kJ·mol−1 and the entropy of activation; ∆S# = −85 ± 5 J·mol−1·K−1. The ruthenium(II catalyst formed from the reduction of ruthenium(III acetylacetonate provides 1700 turnovers over 100 hours in hydrogen generation from the dehydrogenation of dimethylamine borane before deactivation at 60 °C.

  10. Mesoporous Ruthenium/Ruthenium Oxide Thin Films: Active Electrocatalysts for the Oxygen Evolution Reaction

    Kibsgaard, Jakob; Hellstern, Thomas R.; Choi, Shin-Jung

    2017-01-01

    We report the first synthesis of a fully contiguous large area supported thin film of highly ordered mesoporous Ru and RuO2 and investigate the electrocatalytic properties towards the oxygen evolution reaction (OER). We find that the nanoscale porous network of these catalysts provides significant...... enhancements in geometric OER activity without any loss in specific activity. This work demonstrates a strategy for engineering materials at the nanoscale that can simultaneously decrease precious metal loading and increase electrode activity....

  11. The effect of promoters on the electronic structure of ruthenium catalysts supported on carbon

    Guraya, Monica; Sprenger, Susanne; Rarog-Pilecka, Wioletta; Szmigiel, Dariusz; Kowalczyk, Zbigniew; Muhler, Martin

    2004-01-01

    Alkali- and earth-alkali-promoted ruthenium catalysts supported on graphitized carbon were investigated by means of X-ray and ultraviolet photoelectron spectroscopy (XPS and UPS) in order to study the effect of promoters on the electronic structure of this metal-support system. Samples were measured as prepared and after thorough reduction in hydrogen. The C 1s spectra of reduced alkali-promoted catalysts showed a shift towards higher binding energies and an asymmetric broadening. Neither non-promoted nor Ba-promoted Ru/C samples exhibited such a behaviour after similar treatments. The most important feature in the UP spectra of the reduced alkali-promoted catalysts was the appearance of a well defined Fermi edge absent in the semimetal-like electronic structure of graphite. No significant effects appeared in the case of non-promoted or Ba-promoted catalysts. The increase in the density of occupied states at the Fermi energy indicates a shift of this level into the conduction band, due to a charge transfer from the promoter to the support. This interpretation also provides an explanation for the observed higher C 1s binding energy and asymmetric broadening, due to the off-set introduced in the binding energy scale and the increasing probability of inelastic excitations near the Fermi level. In addition to photoelectron spectroscopy, low energy ion scattering (ISS) was used to obtain information about the localisation of the promoters. Based on the mild sputtering effect during prolonged series of spectra, it was possible to conclude that potassium covers both the carbon support and the Ru metal particles

  12. The Biological Side of Water-Soluble Arene Ruthenium Assemblies

    Bruno Therrien

    2014-01-01

    Full Text Available This review article covers the synthetic strategies, structural aspects, and host-guest properties of ruthenium metalla-assemblies, with a special focus on their use as drug delivery vectors. The two-dimensional metalla-rectangles show interesting host-guest possibilities but seem less appropriate for being used as drug carriers. On the other hand, metalla-prisms allow encapsulation and possible targeted release of bioactive molecules and consequently show some potential as drug delivery vectors. The reactivity of these metalla-prisms can be fine-tuned to allow a fine control of the guest’s release. The larger metalla-cubes can be used to stabilize the formation of G-quadruplex DNA and can be used to encapsulate and release photoactive molecules such as porphins. These metalla-assemblies demonstrate great prospective in photodynamic therapy.

  13. Raman spectra of ruthenium and tantalum trimers in argon matrices

    Fang, Li; Shen, Xiaole; Chen, Xiaoyu; Lombardi, John R.

    2000-12-01

    The resonance Raman spectra of ruthenium trimers (Ru 3) in argon matrices have been obtained. Three resonance Raman transitions were observed between 570 and 590 nm. Two of them (303.4 and 603.7 cm -1) are assigned to the totally symmetric vibrational progression, giving k e=1.86 mdyne/ Å. The line at 581.5 cm-1 is assigned as the origin of a low-lying electronic state. We also report on the observation of a resonance Raman spectrum of tantalum trimers (Ta 3). Observed lines include 251.2 and 501.9 cm-1 which we assign to the fundamental and the first overtone of the symmetric stretch in Ta 3. This gives k e=2.25 mdyne/ Å.

  14. Evidence for Dynamic Chemical Kinetics at Individual Molecular Ruthenium Catalysts.

    Easter, Quinn T; Blum, Suzanne A

    2018-02-05

    Catalytic cycles are typically depicted as possessing time-invariant steps with fixed rates. Yet the true behavior of individual catalysts with respect to time is unknown, hidden by the ensemble averaging inherent to bulk measurements. Evidence is presented for variable chemical kinetics at individual catalysts, with a focus on ring-opening metathesis polymerization catalyzed by the second-generation Grubbs' ruthenium catalyst. Fluorescence microscopy is used to probe the chemical kinetics of the reaction because the technique possesses sufficient sensitivity for the detection of single chemical reactions. Insertion reactions in submicron regions likely occur at groups of many (not single) catalysts, yet not so many that their unique kinetic behavior is ensemble averaged. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Separation of carrier-free rhodium isotopes from ruthenium cyclotron targets by the extraction of nitrosylruthenium from hydrochloric acid solution

    Haasbroek, F.J.; Strelow, F.W.E.; Van der Walt, T.N.

    1981-01-01

    A method is presented for the separation of rhodium isotopes from ruthenium cyclotron targets. After bombardment with deuterons and dissolution of the target material, the ruthenium is converted into a nitrosyl complex by treatment with hydroxylammonium chloride. Aluminium and other elements which have been introduced in the dissolution step, are separated by cation exchange. Ruthenium is then separated by extraction with a mixture of tri-n-butyl phosphate and hexane (4:1), leaving the rhodium in the aqueous phase. No ruthenium is found in the rhodium fraction and the recovery of rhodium is better than 90 per cent [af

  16. A non-equilibrium ortho-to-para ratio of water in the Orion PDR

    Choi, Y.; van der Tak, F. F. S.; Bergin, E. A.; Plume, R.

    2014-01-01

    Context. The ortho-to-para ratio (OPR) of H2O is thought to be sensitive to the temperature of water formation. The OPR of H2O is thus useful for studying the formation mechanism of water. Aims: We investigate the OPR of water in the Orion PDR (photon-dominated region), at the Orion Bar and Orion S

  17. Accuracy comparison of Pléiades satellite ortho-images using GPS ...

    resolution satellite ortho-image when different types of ground control are used. This required the execution of two orthorectification tests where only the type of GCPs differed. The results of these tests were interesting since it highlighted the ...

  18. Cu(II)-mediated ortho C-H alkynylation of (hetero)arenes with terminal alkynes.

    Shang, Ming; Wang, Hong-Li; Sun, Shang-Zheng; Dai, Hui-Xiong; Yu, Jin-Quan

    2014-08-20

    Cu(II)-promoted ortho alkynylation of arenes and heteroarenes with terminal alkynes has been developed to prepare aryl alkynes. A variety of arenes and terminal alkynes bearing different substituents are compatible with this reaction, thus providing an alternative disconnection to Sonogashira coupling.

  19. Development and applications of injectable poly(ortho esters) for pain control and periodontal treatment.

    Helle, J; Barr, J; Ng, S Y; Shen, H R; Schwach-Abdellaoui, K; Gurny, R; Vivien-Castioni, N; Loup, P J; Baehni, P; Mombelli, A

    2002-11-01

    Poly(ortho esters) with a low glass transition temperature are semi-solid materials so that therapeutic agents can be incorporated at room temperature, without the use of solvents, by a simple mixing procedure. When molecular weights are limited to pain are under development and human clinical trials using the decanediol polymer for the treatment of periodontitis are also underway.

  20. Regioselective desymmetrization of diaryltetrahydrofurans via directed ortho-lithiation: an unexpected help from green chemistry.

    Mallardo, Valentina; Rizzi, Ruggiero; Sassone, Francesca C; Mansueto, Rosmara; Perna, Filippo M; Salomone, Antonio; Capriati, Vito

    2014-08-14

    An efficient functionalization of diaryltetrahydrofurans via a regioselective THF-directed ortho-lithiation is first described. This reaction can be successfully carried out in cyclopentyl methyl ether as a "greener" alternative to Et2O, with better results in terms of yield and selectivity and, surprisingly, also in protic eutectic mixtures competitively with protonolysis.

  1. Ether-Directed ortho-C–H Olefination with a PdII/MPAA Catalyst**

    Li, Gang; Leow, Dasheng; Wan, Li; Yu, Jin-Quan

    2013-01-01

    Weak coordination is powerful! A PdII-catalyzed olefination of ortho-C–H bonds of arenes directed by weakly coordinating ethers is developed using mono-protected amino acid (MPAA) ligands. This finding provides a method for chemically modifying ethers, which are abundant in natural products and drug molecules. PMID:23239120

  2. Rh(III)-catalyzed olefination of N-sulfonyl imines: synthesis of ortho-olefinated benzaldehydes.

    Zhang, Tao; Wu, Lamei; Li, Xingwei

    2013-12-20

    Rh(III)-catalyzed olefination of N-sulfonyl imines using acrylates and styrenes has been achieved for the synthesis of ortho-olefinated benaldehydes. This reaction proceeds via a chelation assisted C-H olefination/in situ hydrolysis process.

  3. RANDOM COPOLYMER BLENDS OF STYRENE, PARA-FLUORO STYRENE AND ORTHO-FLUORO STYRENE

    OUDHUIS, AACM; TENBRINKE, G; KARASZ, FE

    1993-01-01

    This study completes the investigation of the phase behaviour of polymer blends involving styrene (S), ortho-fluoro styrene (oFS) and para-fluoro styrene (pFS). As before, due to the proximity of the glass transition temperatures of most blends investigated, the miscibility or immiscibility is

  4. Substituent effects in the ortho position: Model compounds with a removed reaction centre

    Böhm, S.; Exner, Otto

    2007-01-01

    Roč. 81, 5/6 (2007), s. 993-1006 ISSN 0137- 5083 Institutional research plan: CEZ:AV0Z40550506 Keywords : substituent effect * density functional theory * ortho effect * steric effect Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 0.483, year: 2007

  5. Incorporation of Ortho- and Meta-Tyrosine Into Cellular Proteins Leads to Erythropoietin-Resistance in an Erythroid Cell Line

    Esztella Mikolás

    2014-04-01

    Full Text Available Background/Aims: Erythropoietin-resistance is an unsolved concern in the treatment of renal anaemia. We aimed to investigate the possible role of ortho- and meta-tyrosine - the hydroxyl free radical products of L-phenylalanine - in the development of erythropoietin-resistance. Methods: TF-1 erythroblast cell line was used. Cell concentration was determined on day 1; 2 and 3 by two independent observers simultaneously in Bürker cell counting chambers. Protein concentration was determined with colorimetric method. Para-, ortho- and meta-tyrosine levels were measured using reverse phase-HPLC with fluorescence detection. Using Western blot method activating phosphorylation of STAT5 and ERK1/2 were investigated. Results: We found a time- and concentration-dependent decrease of erythropoietin-induced proliferative activity in case of ortho- and meta-tyrosine treated TF-1 erythroblasts, compared to the para-tyrosine cultured cells. Decreased erythropoietin-response could be regained with a competitive dose of para-tyrosine. Proteins of erythroblasts treated by ortho- or meta-tyrosine had lower para-tyrosine and higher ortho- or meta-tyrosine content. Activating phosphorylation of ERK and STAT5 due to erythropoietin was practically prevented by ortho- or meta-tyrosine treatment. Conclusion: According to this study elevated ortho- and meta-tyrosine content of erythroblasts may lead to the dysfunction of intracellular signaling, resulting in erythropoietin-hyporesponsiveness.

  6. Pharmacophore Modelling and 4D-QSAR Study of Ruthenium(II) Arene Complexes as Anticancer Agents (Inhibitors) by Electron Conformational- Genetic Algorithm Method.

    Yavuz, Sevtap Caglar; Sabanci, Nazmiye; Saripinar, Emin

    2018-01-01

    The EC-GA method was employed in this study as a 4D-QSAR method, for the identification of the pharmacophore (Pha) of ruthenium(II) arene complex derivatives and quantitative prediction of activity. The arrangement of the computed geometric and electronic parameters for atoms and bonds of each compound occurring in a matrix is known as the electron-conformational matrix of congruity (ECMC). It contains the data from HF/3-21G level calculations. Compounds were represented by a group of conformers for each compound rather than a single conformation, known as fourth dimension to generate the model. ECMCs were compared within a certain range of tolerance values by using the EMRE program and the responsible pharmacophore group for ruthenium(II) arene complex derivatives was found. For selecting the sub-parameter which had the most effect on activity in the series and the calculation of theoretical activity values, the non-linear least square method and genetic algorithm which are included in the EMRE program were used. In addition, compounds were classified as the training and test set and the accuracy of the models was tested by cross-validation statistically. The model for training and test sets attained by the optimum 10 parameters gave highly satisfactory results with R2 training= 0.817, q 2=0.718 and SEtraining=0.066, q2 ext1 = 0.867, q2 ext2 = 0.849, q2 ext3 =0.895, ccctr = 0.895, ccctest = 0.930 and cccall = 0.905. Since there is no 4D-QSAR research on metal based organic complexes in the literature, this study is original and gives a powerful tool to the design of novel and selective ruthenium(II) arene complexes. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

  7. Design and development of novel MRI compatible zirconium- ruthenium alloys with ultralow magnetic susceptibility.

    Li, H F; Zhou, F Y; Li, L; Zheng, Y F

    2016-04-19

    In the present study, novel MRI compatible zirconium-ruthenium alloys with ultralow magnetic susceptibility were developed for biomedical and therapeutic devices under MRI diagnostics environments. The results demonstrated that alloying with ruthenium into pure zirconium would significantly increase the strength and hardness properties. The corrosion resistance of zirconium-ruthenium alloys increased significantly. High cell viability could be found and healthy cell morphology observed when culturing MG 63 osteoblast-like cells and L-929 fibroblast cells with zirconium-ruthenium alloys, whereas the hemolysis rates of zirconium-ruthenium alloys are zirconium-ruthenium alloys (1.25 × 10(-6) cm(3)·g(-1)-1.29 × 10(-6) cm(3)·g(-1) for zirconium-ruthenium alloys) are ultralow, about one-third that of Ti-based alloys (Ti-6Al-4V, ~3.5 × 10(-6) cm(3)·g(-1), CP Ti and Ti-6Al-7Nb, ~3.0 × 10(-6) cm(3)·g(-1)), and one-sixth that of Co-Cr alloys (Co-Cr-Mo, ~7.7 × 10(-6) cm(3)·g(-1)). Among the Zr-Ru alloy series, Zr-1Ru demonstrates enhanced mechanical properties, excellent corrosion resistance and cell viability with lowest magnetic susceptibility, and thus is the optimal Zr-Ru alloy system as therapeutic devices under MRI diagnostics environments.

  8. Behavior of ruthenium in the case of shutdown of the cooling system of HLLW storage tanks

    Philippe, M.; Mercier, J.P.; Gue, J.P.

    1990-01-01

    The consequences of the failure of the cooling system of fission product storage tanks over a variable period were investigated as part of the safety analysis of the La Hague spent fuel reprocessing plant. Due to the considerable heat release, induced by the fission products, a prolonged shutdown of the tank cooling system could cause the progressive evaporation of the solutions to dryness, and culminate in the formation of volatile species of ruthenium and their release in the tank venting circuit. To determine the fraction of ruthenium likely to be transferred from the storage tanks in volatile or aerosol form during the failure, evaporation tests were conducted by evaporating samples of actual nitric acid solutions of fission products, obtained on the laboratory scale after the reprocessing of several kilograms of MOX fuels irradiated to 30,000 MWday.t -1 . A distillation apparatus was designed to operate with small volume solution samples, reproducing the heating conditions existing in the reprocessing plant within a storage tank for fission products. The main conclusions drawn from these experiments are as follows: - ruthenium is only volatilized in the final phase of evaporation, just before desiccation, - for a final temperature limited to 160 0 C, the total fraction of volatilized ruthenium reaches 12%, in the presence of H 2 0, HN0 3 , N0 x and 0 2 , the volatilized ruthenium recombines mainly in the form of ruthenium nitrosyl nitrates, or decomposes into ruthenium oxide on the walls of the apparatus. Assuming a heating power density of 10 W/liter of concentrate, and a perfectly adiabatic storage system, the minimum time required to reach dryness can be estimated at 90 h, allowing substantial time to take action to restore a cooling source

  9. Behavior of ruthenium in the case of shutdown of the cooling system of HLLW storage tanks

    Philippe, M.; Mercier, J.P.; Gue, J.P.

    1991-01-01

    The consequences of the failure of the cooling system of fission product storage tanks over a variable period were investigated as part of the safety analysis of the La Hague spent fuel reprocessing plant. Due to the considerable heat release, induced by the fission products, a prolonged shutdown of the tank cooling system could cause the progressive evaporation of the solutions to dryness, and culminate in the formation of volatile species of ruthenium and their release in the tank venting circuit. To determine the fraction of ruthenium likely to be transferred from the storage tanks in volatile or aerosol form during the failure, evaporation tests were conducted by evaporating samples of actual nitric acid solutions of fission products, obtained on the laboratory scale after the reprocessing of several kilograms of MOX fuels irradiated to 30,000 MW day·t -1 . A distillation apparatus was designed to operate with small-volume solution samples, reproducing the heating conditions existing in the reprocessing plant within a storage tank for fission products. The main conclusions drawn from these experiments are as follows: ruthenium is only volatilized in the final phase of evaporation, just before desiccation; for a final temperature limited to 160 degree C, the total fraction of volatilized ruthenium reaches 12%; in the presence of H 2 O, HNO 3 , NO x and O 2 , the volatilized ruthenium recombines mainly in the form of ruthenium nitrosyl nitrates, or decomposes into ruthenium oxide (probably RuO 2 ) on the walls of the apparatus. Assuming a heating power density of 10 W/liter of concentrate, and a perfectly adiabatic storage system, the minimum time required to reach dryness can be estimated at 90 h, allowing substantial time to take action to restore a cooling source

  10. Design and development of novel MRI compatible zirconium- ruthenium alloys with ultralow magnetic susceptibility

    Li, H.F.; Zhou, F.Y.; Li, L.; Zheng, Y.F.

    2016-01-01

    In the present study, novel MRI compatible zirconium-ruthenium alloys with ultralow magnetic susceptibility were developed for biomedical and therapeutic devices under MRI diagnostics environments. The results demonstrated that alloying with ruthenium into pure zirconium would significantly increase the strength and hardness properties. The corrosion resistance of zirconium-ruthenium alloys increased significantly. High cell viability could be found and healthy cell morphology observed when culturing MG 63 osteoblast-like cells and L-929 fibroblast cells with zirconium-ruthenium alloys, whereas the hemolysis rates of zirconium-ruthenium alloys are alloys and Ti-based alloys, the magnetic susceptibilities of the zirconium-ruthenium alloys (1.25 × 10−6 cm3·g−1–1.29 × 10−6 cm3·g−1 for zirconium-ruthenium alloys) are ultralow, about one-third that of Ti-based alloys (Ti–6Al–4V, ~3.5 × 10−6 cm3·g−1, CP Ti and Ti–6Al–7Nb, ~3.0 × 10−6 cm3·g−1), and one-sixth that of Co–Cr alloys (Co–Cr–Mo, ~7.7 × 10−6 cm3·g−1). Among the Zr–Ru alloy series, Zr–1Ru demonstrates enhanced mechanical properties, excellent corrosion resistance and cell viability with lowest magnetic susceptibility, and thus is the optimal Zr–Ru alloy system as therapeutic devices under MRI diagnostics environments. PMID:27090955

  11. Excitation energy transfer in ruthenium (II)-porphyrin conjugates led to enhanced emission quantum yield and {sup 1}O{sub 2} generation

    Pan, Jie; Jiang, Lijun; Chan, Chi-Fai [Department of Chemistry, Hong Kong Baptist University, Kowloon Tong, Hong Kong Special Administrative Region (Hong Kong); Tsoi, Tik-Hung [Department of Applied Biology and Chemical Technology, Hung Hom, Hong Kong Special Administrative Region (Hong Kong); Shiu, Kwok-Keung; Kwong, Daniel W.J. [Department of Chemistry, Hong Kong Baptist University, Kowloon Tong, Hong Kong Special Administrative Region (Hong Kong); Wong, Wing-Tak [Department of Applied Biology and Chemical Technology, Hung Hom, Hong Kong Special Administrative Region (Hong Kong); Wong, Wai-Kwok, E-mail: wkwong@hkbu.edu.hk [Department of Chemistry, Hong Kong Baptist University, Kowloon Tong, Hong Kong Special Administrative Region (Hong Kong); Wong, Ka-Leung, E-mail: klwong@hkbu.edu.hk [Department of Chemistry, Hong Kong Baptist University, Kowloon Tong, Hong Kong Special Administrative Region (Hong Kong)

    2017-04-15

    Porphyrins are good photodynamic therapy (PDT) agents due to its flexibility for modifications to achieve tumor localization and photo-cytotoxicity against cancer. Yet they are not perfect. In a Ru(polypyridyl)-porphyrin system, the Ru(polypyridyl) moiety improves the water solubility and cell permeability. Consider the similar excited state energies between Ru(polypyridyl) and porphyrin moieties; a small perturbation (e.g. Zn(II) metalation) would lead to a marked change in the energy migration process. In this work, we have synthesized a series of porphyrins conjugated with Ru(polypyridyl) complexes using different linkers and investigated their photophysical properties, which included singlet oxygen quantum yield and their in vitro biological properties, resulting from linker variation and porphyrin modification by Zn(II) metalation. - Graphical abstract: Four amphiphilic ruthenium(II)-porphyrin complexes were prepared that display energy transfer conversion with zinc coordination, lysosome specific target, low dark toxicity and efficient photodynamic therapy.

  12. Assessing Rare Metal Availability Challenges for Solar Energy Technologies

    Leena Grandell

    2015-08-01

    Full Text Available Solar energy is commonly seen as a future energy source with significant potential. Ruthenium, gallium, indium and several other rare elements are common and vital components of many solar energy technologies, including dye-sensitized solar cells, CIGS cells and various artificial photosynthesis approaches. This study surveys solar energy technologies and their reliance on rare metals such as indium, gallium, and ruthenium. Several of these rare materials do not occur as primary ores, and are found as byproducts associated with primary base metal ores. This will have an impact on future production trends and the availability for various applications. In addition, the geological reserves of many vital metals are scarce and severely limit the potential of certain solar energy technologies. It is the conclusion of this study that certain solar energy concepts are unrealistic in terms of achieving TW scales.

  13. Highly efficient quenching of tris(2,2'-bipyridyl)ruthenium(II) electrochemiluminescence by ozone using formaldehyde, methylglyoxal, and glyoxalate as co-reactants and its application to ozone sensing.

    Gao, Ying; Liu, Xiaoyun; Qi, Wenjing; Gao, Wenyue; Li, Yunhui; Xu, Guobao

    2015-06-21

    Most electrochemiluminescence (ECL) systems require high concentrations of quencher to totally quench ECL. In this study, we found that ozone can quench tris(2,2'-bipyridyl)ruthenium(II) ECL using formaldehyde, methylglyoxal, or glyoxalate as co-reactants at a glassy carbon electrode with remarkable efficiencies even when the concentration of ozone is merely 0.25% of that of the co-reactant. The strongest quenching is observed with the tris(2,2'-bipyridyl)ruthenium(II)/formaldehyde ECL system. The tris(2,2'-bipyridyl)ruthenium(II)/formaldehyde ECL intensities decrease linearly with the ozone concentration over the range of 0.025-25 μM (r = 0.9947) with a limit of detection of 8 nM. The method is more sensitive and faster than most methods. It shows high selectivity in the presence of other ROS or oxidants and some metal ions, such as H2O2, ClO(-), Mg(2+), Ni(2+), etc. The method exhibits high recoveries for the detection of ozone in a ventilated photocopy room.

  14. Ground vs. excited state interaction in ruthenium-thienyl dyads : implications for through bond interactions in multicomponent systems

    Henry, William; Browne, Wesley R.; Ronayne, Kate L.; O’Boyle, Noel M.; Vos, Johannes G.; McGarvey, John J.

    2005-01-01

    The vibrational and photophysical properties of mononuclear ruthenium(II) and ruthenium(III) polypyridyl complexes based on the, ligands 2-(5-(pyridin-2"-yl)-1'H-1',2',4'-triaz-3'-yl)-thiophene, 2-(5-(pyrazin-2"-yl)-1'H-1',2,4-triaz-3'-yl)-thiophene, are reported. The effect of the introduction of

  15. Dehydrogenative Coupling of Primary Alcohols To Form Esters Catalyzed by a Ruthenium N-Heterocyclic Carbene Complex

    Sølvhøj, Amanda Birgitte; Madsen, Robert

    2011-01-01

    The ruthenium complex [RuCl2(IiPr)(p-cymene)] catalyzes the direct condensation of primary alcohols into esters and lactones with the release of hydrogen gas. The reaction is most effective with linear aliphatic alcohols and 1,4-diols and is believed to proceed with a ruthenium dihydride...

  16. A facile one-pot synthesis of ruthenium hydroxide nanoparticles on magnetic silica: Aqueous hydration of nitriles to amides

    One-pot synthesis of ruthenium hydroxide nanoparticles on magnetic silica is described which involve the in situ generation of magnetic silica (Fe3O4@ SiO2) and ruthenium hydroxide immobilization; the hydration of nitriles occurs in high yield and excellent selectivity using this...

  17. One-pot hydrothermal synthesis of ruthenium oxide nanodots on reduced graphene oxide sheets for supercapacitors

    Chen Yao [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China); Graduate University of Chinese Academy Sciences, Beijing 100049 (China); Zhang Xiong [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China); Zhang Dacheng [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China); Graduate University of Chinese Academy Sciences, Beijing 100049 (China); Ma Yanwei, E-mail: ywma@mail.iee.ac.cn [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China)

    2012-01-15

    Highlights: > Graphite oxide instead of graphene as precursor has been used to synthesize reduced graphene oxide/ruthenium oxide composites by a hydrothermal treatment. > Using NaOH solution to adjust pH of GO colloids leads to homogeneous ruthenium oxide deposited on reduced graphene oxide sheets. > A maximum capacitance of 471 F g{sup -1} is obtained at 0.5 A g{sup -1} for the composites when loading 40% of RuO{sub 2} and its life retention reaches 92% after 3000 cycles. - Abstract: Ruthenium oxide nanodots have been deposited on reduced graphene oxide (RGO) sheets homogeneously by hydrothermal and annealing methods. Adding NaOH solution in GO colloids prevents the restack and agglomeration of GO sheets when mixed with ruthenium chloride solution. Local crystallization of RuO{sub 2} in the composites is revealed by X-ray diffraction and transmission electron microscopy. The element mapping image demonstrates the uniform distribution of Ru on RGO sheets. Unlike the pure crystalline RuO{sub 2} exhibiting poor electrochemical performance, the composites present superior capacitive properties. The hydrothermal time is optimized and a maximum of 471 F g{sup -1} is measured in the composites at 0.5 A g{sup -1} when loaded with 45 wt% of RuO{sub 2}. After 3000 cycles, its specific capacitance remains 92% of the maximum capacitance. Our results suggest potential application of the reduced graphene oxide/ruthenium oxide composites to supercapacitors.

  18. One-pot hydrothermal synthesis of ruthenium oxide nanodots on reduced graphene oxide sheets for supercapacitors

    Chen Yao; Zhang Xiong; Zhang Dacheng; Ma Yanwei

    2012-01-01

    Highlights: → Graphite oxide instead of graphene as precursor has been used to synthesize reduced graphene oxide/ruthenium oxide composites by a hydrothermal treatment. → Using NaOH solution to adjust pH of GO colloids leads to homogeneous ruthenium oxide deposited on reduced graphene oxide sheets. → A maximum capacitance of 471 F g -1 is obtained at 0.5 A g -1 for the composites when loading 40% of RuO 2 and its life retention reaches 92% after 3000 cycles. - Abstract: Ruthenium oxide nanodots have been deposited on reduced graphene oxide (RGO) sheets homogeneously by hydrothermal and annealing methods. Adding NaOH solution in GO colloids prevents the restack and agglomeration of GO sheets when mixed with ruthenium chloride solution. Local crystallization of RuO 2 in the composites is revealed by X-ray diffraction and transmission electron microscopy. The element mapping image demonstrates the uniform distribution of Ru on RGO sheets. Unlike the pure crystalline RuO 2 exhibiting poor electrochemical performance, the composites present superior capacitive properties. The hydrothermal time is optimized and a maximum of 471 F g -1 is measured in the composites at 0.5 A g -1 when loaded with 45 wt% of RuO 2 . After 3000 cycles, its specific capacitance remains 92% of the maximum capacitance. Our results suggest potential application of the reduced graphene oxide/ruthenium oxide composites to supercapacitors.

  19. Mitigation of strontium and ruthenium release in the CANDU primary heat transport system

    McFarlane, J

    1998-03-01

    In certain severe accident scenarios, low-volatility fission products can appear to contribute significantly to dose, if treated with undue conservatism. Hence a survey was performed, to see if factors that may mitigate release of strontium and ruthenium could be incorporated into safety analyses, to cover parameters such as location in the fuel matrix under normal operating conditions, release from fuel, transport and deposition in the primary heat transport system and chemistry. In addition chemical equilibrium calculations were performed to investigate the volatility of strontium and ruthenium in the presence of uranium and important fission products. Strontium is very soluble in the U0{sub 2} fuel, up to 12 atom %, and hence release is improbable, particularly under oxidizing conditions until volatilization of the fuel matrix itself occurs. Ruthenium, however, can be released at low temperatures, but only under oxidizing conditions. These may occur during a fuel-handling accident or as a result of an end-fitting failure. Under these conditions, the primary heat transport system cannot be credited for retention. The volatile form of ruthenium, RuO{sub 4}(g), is thermally unstable above 381 K and decomposes to RuO{sub 2}(s) and O{sub 2}(g) upon contact with surfaces, a factor that is likely to minimize the release of ruthenium into the environment. (author)

  20. Mitigation of strontium and ruthenium release in the CANDU primary heat transport system

    McFarlane, J.

    1998-03-01

    In certain severe accident scenarios, low-volatility fission products can appear to contribute significantly to dose, if treated with undue conservatism. Hence a survey was performed, to see if factors that may mitigate release of strontium and ruthenium could be incorporated into safety analyses, to cover parameters such as location in the fuel matrix under normal operating conditions, release from fuel, transport and deposition in the primary heat transport system and chemistry. In addition chemical equilibrium calculations were performed to investigate the volatility of strontium and ruthenium in the presence of uranium and important fission products. Strontium is very soluble in the U0 2 fuel, up to 12 atom %, and hence release is improbable, particularly under oxidizing conditions until volatilization of the fuel matrix itself occurs. Ruthenium, however, can be released at low temperatures, but only under oxidizing conditions. These may occur during a fuel-handling accident or as a result of an end-fitting failure. Under these conditions, the primary heat transport system cannot be credited for retention. The volatile form of ruthenium, RuO 4 (g), is thermally unstable above 381 K and decomposes to RuO 2 (s) and O 2 (g) upon contact with surfaces, a factor that is likely to minimize the release of ruthenium into the environment. (author)

  1. pH-triggered chitosan nanogels via an ortho ester-based linkage for efficient chemotherapy.

    Yang, Guanqing; Wang, Xin; Fu, Shengxiang; Tang, Rupei; Wang, Jun

    2017-09-15

    We report on new types of chitosan-based nanogels via an ortho ester-based linkage, used as drug carriers for efficient chemotherapy. First, we synthesized a novel diacrylamide containing ortho ester (OEAM) as an acid-labile cross-linker. Subsequently, methacrylated succinyl-chitosan (MASCS) was prepared and polymerized with OEAM at different molar ratios to give a series of pH-triggered MASCS nanogels. Doxorubicin (DOX) as a model anticancer drug was loaded into MASCS nanogels with a loading content of 16.5%. As expected, with the incorporation of ortho ester linkages, these nanogels showed pH-triggered degradation and drug release at acidic pH values. In vitro cellular uptake shows that the DOX-loaded nanogels could be preferentially internalized by two-dimensional (2D) cells and three-dimensional (3D) multicellular spheroids (MCs), resulting in higher inhibition of the proliferation of tumor cells. In vivo biodistribution and anti-tumor effect were determined in H22 tumor-bearing mice, and the results demonstrate that the acid-labile MASCS nanogels can significantly prolong the blood circulation time of DOX and improve the accumulation in tumor areas, leading to higher therapeutic efficacy. We designed new pH-triggered chitosan nanogels via an ortho ester-based cross-linker for efficient drug-loading and chemotherapy. These drug-loaded nanogels exhibit excellent pH-triggered drug release behavior due to the degradation of ortho ester linkages in mildly acidic environments. In vitro and in vivo results demonstrate that the nanogels could be efficiently internalized by 2D cells and 3D-MCs, improve drug concentration in solid tumors, and lead to higher therapeutic efficacy. To the best of our knowledge, this is the first report on using an ortho ester-based cross-linker to prepare pH-triggered chitosan nanogels as tumor carriers, which may provide a potential route for improved safety and to increase the therapeutic efficacy of anticancer therapy. Copyright © 2017

  2. Cytotoxicity and anti-tumor effects of new ruthenium complexes on triple negative breast cancer cells.

    Cecília P Popolin

    Full Text Available Triple-negative breast cancer (TNBC is a highly aggressive breast cancer subtype. The high rate of metastasis associated to the fact that these cells frequently display multidrug resistance, make the treatment of metastatic disease difficult. Development of antitumor metal-based drugs was started with the discovery of cisplatin, however, the severe side effects represent a limitation for its clinical use. Ruthenium (Ru complexes with different ligands have been successfully studied as prospective antitumor drugs. In this work, we demonstrated the activity of a series of biphosphine bipyridine Ru complexes (1 [Ru(SO4(dppb(bipy], (2 [Ru(CO3(dppb(bipy], (3 [Ru(C2O4(dppb(bipy] and (4 [Ru(CH3CO2(dppb(bipy]PF6 [where dppb = 1,4-bis(diphenylphosphinobutane and bipy = 2,2'-bipyridine], on proliferation of TNBC (MDA-MB-231, estrogen-dependent breast tumor cells (MCF-7 and a non-tumor breast cell line (MCF-10A. Complex (4 was most effective among the complexes and was selected to be further investigated on effects on tumor cell adhesion, migration, invasion and in apoptosis. Moreover, DNA and HSA binding properties of this complex were also investigated. Results show that complex (4 was more efficient inhibiting proliferation of MDA-MB-231 cells over non-tumor cells. In addition, complex (4 was able to inhibit MDA-MB231 cells adhesion, migration and invasion and to induce apoptosis and inhibit MMP-9 secretion in TNBC cells. Complex (4 should be further investigated in vivo in order to stablish its potential to improve breast cancer treatment.

  3. 2011 NOAA Ortho-rectified Mosaic of Hampton Harbor to Frost Point, New Hampshire (Mean High Water)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  4. 2011 NOAA Ortho-rectified Near Infrared Mosaic of Hampton Harbor to Frost Point, New Hampshire (Mean Lower Low Water)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  5. 2012 NOAA Ortho-rectified Near-Infrared MLLW Mosaic of Lopez Rock to Pescadero Point, California

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  6. 2013 NOAA Ortho-rectified Near-Infrared Mosaic of Virginia: Norfolk, Hampton Roads,and Newport News

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  7. Ortho-para forms of hydrogen, deuterium, and tritium: radiation and self-induced conversion kinetics and equilibria

    Pyper, J.W.; Briggs, C.K.

    1977-01-01

    The theory of the ortho-para transitions in H 2 , D 2 , and T 2 is developed. Experimental and calculated values of the ortho-para compositions of the three hydrogen isotopes mentioned in the literature are correlated as a function of temperature, and are discussed critically. The kinetics of the radiation and self-induced ortho-para transitions are reviewed. In general, the radiation-induced transitions are more rapid than the self-induced transitions. We estimate (based on data for other systems) that the β-ray-induced ortho-para transitions in liquid D 2 or T 2 would be fast, with a half time on the order of a few minutes. Experiments are proposed to study these transitions in the liquid phase using infrared spectroscopy

  8. 2010 NOAA Ortho-rectified Mosaic from Color Aerial Imagery of BEAUMONT, ORANGE, PORT AUTHUR (NODC Accession 0074380)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative of BEAUMONT, ORANGE,...

  9. NOAA Ortho-rectified Mosaic from Color Aerial Imagery of CHOCTAWHATCHEE BAY, FL, 2009 - 2010 (NODC Accession 0086137)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative of CHOCTAWHATCHEE BAY....

  10. 2014 NOAA Ortho-rectified Mean High Water Near- Infrared Mosaic of Cedar Key to Tarpon Springs, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  11. Conversion rate of para-hydrogen to ortho-hydrogen by oxygen: implications for PHIP gas storage and utilization.

    Wagner, Shawn

    2014-06-01

    To determine the storability of para-hydrogen before reestablishment of the room temperature thermal equilibrium mixture. Para-hydrogen was produced at near 100% purity and mixed with different oxygen quantities to determine the rate of conversion to the thermal equilibrium mixture of 75: 25% (ortho: para) by detecting the ortho-hydrogen (1)H nuclear magnetic resonance using a 9.4 T imager. The para-hydrogen to ortho-hydrogen velocity constant, k, near room temperature (292 K) was determined to be 8.27 ± 1.30 L/mol · min(-1). This value was calculated utilizing four different oxygen fractions. Para-hydrogen conversion to ortho-hydrogen by oxygen can be minimized for long term storage with judicious removal of oxygen contamination. Prior calculated velocity rates were confirmed demonstrating a dependence on only the oxygen concentration.

  12. 2011 NOAA Ortho-rectified Mosaic of Hampton Harbor to Frost Point, New Hampshire (Mean Lower Low Water)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  13. 2010 NOAA Ortho-rectified Near-Infrared MHW Mosaic of South Carolina: Hilton Head to St. Helena Sound

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  14. 2010 NOAA Ortho-rectified Color MHW Mosaic of South Carolina: Hilton Head to St. Helena Sound

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  15. 2012 NOAA Ortho-rectified Near-Infrared MLLW Mosaic of Alabama: Bon Secour Bay and Weeks Bay NERR

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  16. 2012 NOAA Ortho-rectified Color MLLW Mosaic of Alabama: Bon Secour Bay and Weeks Bay NERR

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  17. 2012 NOAA Ortho-rectified Near-Infrared MLLW Mosaic of Pescadero Point to Bodega Bay, California

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  18. 2015 NOAA Ortho-rectified Color Mosaic of San Diego, California: Integrated Ocean and Coastal Mapping Product

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  19. 2010 NOAA Near Infrared Ortho-rectified Mosaic of Louisiana: Mississippi River - Baton Rouge to Southwest Pass (NODC Accession 0104414)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  20. 2011 NOAA Ortho-rectified Mosaic of Merrimack River and Plum Island Sound, Massachusetts (Mean High Water)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  1. 2012 NOAA Ortho-rectified Near-Infrared Mosaic of Oregon: Columbia River - Bonneville Dam to Lake Umatilla

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  2. 2016 NOAA NGS Ortho-rectified Mean High Water Near-Infrared Mosaic of Venice Inlet ICW, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  3. 2016 NOAA NGS Ortho-rectified Mean High Water Color Mosaic of South Venice to Marco Island, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  4. 2014 NOAA NGS Ortho-rectified Mean Low Low Water Color Mosaic of Venice Inlet ICW, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  5. 2014 NOAA NGS Ortho-rectified Mean Low Low Water Near-Infrared Mosaic of Venice Inlet ICW, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  6. 2012 NOAA Ortho-rectified Near-Infrared MLLW Mosaic of Seal Rock to Lopez Rock, California

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  7. 2011 NOAA Ortho-rectified Mosaic of Maine: Reversing Falls at Whiting Bay, Mean Lower Low Water

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  8. 2015 NOAA Ortho-rectified Color Mosaic of Los Angeles and Long Beach, California: Integrated Ocean and Coastal Mapping Product

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  9. 2016 NOAA NGS Ortho-rectified Mean High Water Color Mosaic of St. Johns River at Mile Point Turn, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  10. 2016 NOAA NGS Ortho-rectified Mean Low Low Water Color Mosaic of St Johns River, Florida

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  11. 2012 NOAA Near Infrared MLLW Ortho-rectified Mosaic of Northeast Point to Murphy Island, South Carolina

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative. The source imagery...

  12. 2010 NOAA Ortho-rectified Mosaic from Color Aerial Imagery of MISSISSIPPI RIVER - BATON ROUGE TO LAPLACE (NODC Accession 0074374)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles, created as a product from the NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative of MISSISSIPPI RIVER -...

  13. Interaction of ruthenium (4) and osmium (4) with 2-mercaptobenzimidazole, 2-mercaptobenzoxazole and 2-mercaptobenzothiazole in the presence of edta

    Busev, A.I.; Ignat'eva, T.I.; Lomakina, L.N.

    1975-01-01

    Interaction of ruthenium (4) and osmium (4) with 2-mercaptobenzimidazole (2MBI), 2-mercaptobenzoxazole (2MBO) and 2-mercaptobenzothiazole (2MBT) in the presence of EDTA was studied. The interaction of ruthenium (4) and osmium (4) with EDTA was constidered. Ruthenium complex is formed with constant output at 2-4.5 pH after 30 min.heating. In the lowacid solution (pH 2-4) osmium reacts with EDTA forming soluble compound. Characteristics of ruthenium (4) compound with 2MBI, 2MBO and 2MBT produced in the presence of EDTA are presented. Osmium (4) in the presence of EDTA and above mentioned organic reagents and when heating forms lowsoluble compounds. Possibility of joint determination of ruthenium and osmium with help of 2MBI in the presence of EDTA under conditions of minimum complexing osmium with EDTA was investigated

  14. Interaction of ruthenium (4) and osmium (4) with 2-mercaptobenzimidazole, 2-mercaptobenzoxazole and 2-mercaptobenzothiazole in the presence of EDTA

    Busev, A I; Ignat' eva, T I; Lomakina, L N [Moskovskij Gosudarstvennyj Univ. (USSR). Kafedra Analiticheskoj Khimii

    1975-05-01

    Interaction of ruthenium (4) and osmium (4) with 2-mercaptobenzimidazole (2MBI), 2-mercaptobenzoxazole (2MBO) and 2-mercaptobenzothiazole (2MBT) in the presence of EDTA was studied. The interaction of ruthenium (4) and osmium (4) with EDTA was considered. Ruthenium complex is formed with constant output at 2-4.5 pH after 30 min. heating. In the low acid solution (pH 2-4) osmium reacts with EDTA forming soluble compound. Characteristics of ruthenium (4) compound with 2MBI, 2MBO and 2MBT produced in the presence of EDTA are presented. Osmium (4) in the presence of EDTA and above mentioned organic reagents and when heating forms low soluble compounds. Possibility of joint determination of ruthenium and osmium with help of 2MBI in the presence of EDTA under conditions of minimum complexing osmium with EDTA was investigated.

  15. Electronic structure of the indium tin oxide/nanocrystalline anatase (TiO2)/ruthenium-dye interfaces in dye-sensitized solar cells

    Lyon, J. E.; Rayan, M. K.; Beerbom, M. M.; Schlaf, R.

    2008-10-01

    The electronic structure of two interfaces commonly found in dye-sensitized photovoltaic cells based on nanocrystalline anatase TiO2 ("Grätzel cells") was investigated using photoemission spectroscopy (PES). X-ray photoemission spectroscopy (XPS) and ultraviolet photoemission spectroscopy (UPS) measurements were carried out on the indium tin oxide (ITO)/TiO2 and the TiO2/cis-bis(isothiocyanato)bis(2,2'-bipyridyl-4,4'-dicarboxylato)-ruthenium(II)bis-tetrabutylammonium dye ("N719" or "Ruthenium 535-bisTBA") interfaces. Both contacts were investigated using a multistep deposition procedure where the entire structure was prepared in vacuum using electrospray deposition. In between deposition steps the surface was characterized with XPS and UPS resulting in a series of spectra, allowing the determination of the orbital and band lineup at the interfaces. The results of these efforts confirm previous PES measurements on TiO2/dye contacts prepared under ambient conditions, suggesting that ambient contamination might not have significant influence on the electronic structure at the dye/TiO2 interface. The results also demonstrate that there may be a significant barrier for electron injection at the sputtered ITO/TiO2 interface and that this interface should be viewed as a semiconductor heterojunction rather than as metal-semiconductor (Schottky) contact.

  16. Sensitometric properties of Agfa Dentus OrthoLux, Agfa Dentus ST8G, and Kodak Ektavision panoramic radiographic film.

    Wakoh, M; Nishikawa, K; Kobayashi, N; Farman, A G; Kuroyanagi, K

    2001-02-01

    The purpose of this study was to compare the sensitometric properties of and visualization of anatomical structures with Agfa OrthoLux green-sensitive panoramic radiographic film, Agfa ST8G green sensitive panoramic radiographic film, and Kodak Ektavision green-sensitive panoramic radiographic film used in combination with an Agfa Ortho Regular 400 imaging screen, Kodak Ektavision imaging screen, and Kodak Lanex Regular imaging screen. The density response and resolution of panoramic radiographic film/intensifying screen combinations was evaluated by means of Hunter and Driffield curves, modulation transfer functions, and noise-equivalent number of quanta. Image clarity of selected anatomical structures was rated independently by 6 oral and maxillofacial radiologists. The ISO speed for the Agfa OrthoLux panoramic radiographic film combinations was the fastest, and the ISO speed for the Kodak Ektavision green-sensitive panoramic radiographic film combinations was the slowest. The average gradient for the Agfa ST8G systems was relatively steep in comparison with those for the other film/screen combinations. The modulation transfer functions for the Kodak Ektavision film were higher than those for the other films, irrespective of the screen combination used, and those for Agfa OrthoLux film were slightly higher than those for Agfa ST8G film. The noise-equivalent number of quanta for the Agfa ST8G film/screen combinations was lower than those for the other film/screen combinations. The noise-equivalent number of quanta for the Kodak Ektavision film/screen combinations was well within the high-frequency range, whereas Agfa OrthoLux combined with either the Kodak Ektavision imaging screen or the Kodak Lanex Regular imaging screen produced a noise-equivalent number of quanta similar to those of the Kodak Ektavision film/screen combinations in the low-frequency range. Agfa OrthoLux was perceived to provide clearer images of the selected anatomical details than Agfa ST8G

  17. Ruthenium and iron complexes with benzotriazole and benzimidazole derivatives as simple models for proton-coupled electron transfer systems

    Rocha Reginaldo C.

    2001-01-01

    Full Text Available Iron and ruthenium complexes of the type [M-LH]n (where M = RuII,III(NH35(2+,3+, RuII,III(edta2-,- [edta = ethylenedinitrilotetraacetate], or FeII,III(CN5(3-,2- and LH = benzotriazole or benzimidazole were prepared and characterized in aqueous solutions by means of electrochemical and spectroelectrochemical methods. Special emphasis was given to the pH-dependent redox processes, exhibited by all the investigated complexes. From their related Pourbaix diagrams, which displayed a typically Nernstian behavior, the pKa and formal reduction potential values were extracted. In addition, these E1/2 versus pH curves were also used to illustrate the partitioning relationship concerning the redox and acid-base species, and their interconversion equilibria. The active area in which the dependence of the M III/M II couple on the pH takes place, as delimited by pKaIII and pKaII, was taken into account in order to evaluate the usefulness of such simple complexes as models for proton-coupled electron transfer (PCET. The results were interpreted in terms of the acceptor/donor electronic character of the ligands and sigma,pi-metal-ligand interactions in both redox states of the metal ion.

  18. Ruthenium complexes with phenylterpyridine derivatives target cell membrane and trigger death receptors-mediated apoptosis in cancer cells.

    Deng, Zhiqin; Gao, Pan; Yu, Lianling; Ma, Bin; You, Yuanyuan; Chan, Leung; Mei, Chaoming; Chen, Tianfeng

    2017-06-01

    Elucidation of the communication between metal complexes and cell membrane may provide useful information for rational design of metal-based anticancer drugs. Herein we synthesized a novel class of ruthenium (Ru) complexes containing phtpy derivatives (phtpy = phenylterpyridine), analyzed their structure-activity relationship and revealed their action mechanisms. The result showed that, the increase in the planarity of hydrophobic Ru complexes significantly enhanced their lipophilicity and cellular uptake. Meanwhile, the introduction of nitro group effectively improved their anticancer efficacy. Further mechanism studies revealed that, complex (2c), firstly accumulated on cell membrane and interacted with death receptors to activate extrinsic apoptosis signaling pathway. The complex was then transported into cell cytoplasm through transferrin receptor-mediated endocytosis. Most of the intracellular 2c accumulated in cell plasma, decreasing the level of cellular ROS, inducing the activation of caspase-9 and thus intensifying the apoptosis. At the same time, the residual 2c can translocate into cell nucleus to interact with DNA, induce DNA damage, activate p53 pathway and enhance apoptosis. Comparing with cisplatin, 2c possesses prolonged circulation time in blood, comparable antitumor ability and importantly, much lower toxicity in vivo. Taken together, this study uncovers the role of membrane receptors in the anticancer actions of Ru complexes, and provides fundamental information for rational design of membrane receptor targeting anticancer drugs. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Palladium-Catalyzed ortho-Olefination of Phenyl Acetic and Phenyl Propylacetic Esters via C-H Bond Activation.

    Hu, Jundie; Guan, Mingyu; Han, Jian; Huang, Zhi-Bin; Shi, Da-Qing; Zhao, Yingsheng

    2015-08-21

    A highly regioselective palladium-catalyzed ester-directed ortho-olefination of phenyl acetic and propionic esters with olefins via C-H bond activation has been developed. A wide variety of phenyl acetic and propionic esters were tolerated in this transformation, affording the corresponding olefinated aromatic compounds. The ortho-olefination of heterocyclic acetic and propionic esters also took place smoothly giving the products in good yields, thus proving the potential utility of this protocol in synthetic chemistry.

  20. Coordinatively unsaturated ruthenium complexes as efficient alkyneazide cycloaddition catalysts

    Lamberti, Marina; Fortman, George C.; Poater, Albert; Broggi, Julie; Slawin, Alexandra M. Z.; Cavallo, Luigi; Nolan, Steven P.

    2012-01-01

    The performance of 16-electron ruthenium complexes with the general formula Cp*Ru(L)X (in which L = phosphine or N-heterocyclic carbene ligand; X = Cl or OCH2CF3) was explored in azidealkyne cycloaddition reactions that afford the 1,2,3- triazole products. The scope of the Cp*Ru(PiPr 3)Cl precatalyst was investigated for terminal alkynes leading to new 1,5-disubstituted 1,2,3-triazoles in high yields. Mechanistic studies were conducted and revealed a number of proposed intermediates. Cp*Ru- (PiPr3)(2-HCCPh)Cl was observed and characterized by 1H, 13C, and 31P NMR at temperatures between 273 and 213 K. A rare example of N,N-κ2-phosphazide complex, Cp*Ru(κ2- iPr3PN3Bn)Cl, was fully characterized, and a single-crystal X-ray diffraction structure was obtained. DFT calculations describe a complete map of the catalytic reactivity with phenylacetylene and/or benzylazide. © 2012 American Chemical Society.

  1. Graphene Oxide/ Ruthenium Oxide Composites for Supercapacitors Electrodes

    Amir, Fatima

    Supercapacitors are electrical energy storage devices with high power density, high rate capability, low maintenance cost, and long life cycle. They complement or replace batteries in harvesting applications when high power delivery is needed. An important improvement in performance of supercapacitors has been achieved through recent advances in the development of new nanostructured materials. Here we will discuss the fabrication of graphene oxide/ ruthenium oxide supercacitors electrodes including electrophoretic deposition. The morphology and structure of the fabricated electrodes were investigated and will be discussed. The electrochemical properties were determined using cyclic voltammetry and galvanostatic charge/discharge techniques and the experiments that demonstrate the excellent capacitive properties of the obtained supercapacitors will also be discussed. The fabrication and characterization of the samples were performed at the Center of Functional Nanomaterials at Brookhaven National Lab. The developed approaches in our study represent an exciting direction for designing the next generation of energy storage devices. This work was supported in part by the U.S. Department of Energy through the Visiting Faculty Program and the research used resources of the Center for Functional Nanomaterials at Brookhaven National Laboratory.

  2. Visual acuity after Ruthenium106 brachytherapy of choroidal melanomas

    Damato, Bertil; Patel, Imran M.; Campbell, Ian R.; Mayles, Helen M.; Errington, R. Douglas

    2005-01-01

    Purpose: To report on conservation of visual acuity after Ruthenium 106 (Ru-106) brachytherapy of choroidal melanoma. Methods and materials: This study was a noncomparative interventional case series of 458 patients with choroidal melanoma treated at a single center between January 1993 and December 2001. The intervention consisted of Ru-106 brachytherapy delivering minimum scleral and apex doses of 300 Gy and 80 Gy, respectively, using a 15-mm or 20-mm plaque. For discrete, posterior tumors, the plaque was positioned eccentrically with its posterior edge aligned with the posterior tumor margin. To ensure correct plaque positioning, any overlying extraocular muscles were dis-inserted, and the locations of both tumor and plaque edges were confirmed by transillumination and indentation. The main outcome measures were conservation of vision of 20/40 or better, 20/200 or better, and Counting Fingers or better, according to baseline variables. Results: The actuarial rate of conservation of 20/40 or better was 55% at 9 years, loss of such vision correlating with posterior tumor extension (p 106 brachytherapy of posterior choroidal melanoma achieves good conservation of vision if the tumor does not extend close to the optic nerve or fovea

  3. Coordinatively unsaturated ruthenium complexes as efficient alkyneazide cycloaddition catalysts

    Lamberti, Marina

    2012-01-23

    The performance of 16-electron ruthenium complexes with the general formula Cp*Ru(L)X (in which L = phosphine or N-heterocyclic carbene ligand; X = Cl or OCH2CF3) was explored in azidealkyne cycloaddition reactions that afford the 1,2,3- triazole products. The scope of the Cp*Ru(PiPr 3)Cl precatalyst was investigated for terminal alkynes leading to new 1,5-disubstituted 1,2,3-triazoles in high yields. Mechanistic studies were conducted and revealed a number of proposed intermediates. Cp*Ru- (PiPr3)(2-HCCPh)Cl was observed and characterized by 1H, 13C, and 31P NMR at temperatures between 273 and 213 K. A rare example of N,N-κ2-phosphazide complex, Cp*Ru(κ2- iPr3PN3Bn)Cl, was fully characterized, and a single-crystal X-ray diffraction structure was obtained. DFT calculations describe a complete map of the catalytic reactivity with phenylacetylene and/or benzylazide. © 2012 American Chemical Society.

  4. Rapid visual and spectrophotometric nitrite detection by cyclometalated ruthenium complex.

    Lo, Hoi-Shing; Lo, Ka-Wai; Yeung, Chi-Fung; Wong, Chun-Yuen

    2017-10-16

    Quantitative determination of nitrite ion (NO 2 - ) is of great importance in environmental and clinical investigations. A rapid visual and spectrophotometric assay for NO 2 - detection was developed based on a newly designed ruthenium complex, [Ru(npy)([9]aneS3)(CO)](ClO 4 ) (denoted as RuNPY; npy = 2-(1-naphthyl)pyridine, [9]aneS3 = 1,4,7-trithiacyclononane). This complex traps NO + produced in acidified NO 2 - solution, and yields observable color change within 1 min at room temperature. The assay features excellent dynamic range (1-840 μmol L -1 ) and high selectivity, and its limit of detection (0.39 μmol L -1 ) is also well below the guideline values for drinking water recommended by WHO and U.S. EPA. Practical use of this assay in tap water and human urine was successfully demonstrated. Overall, the rapidity and selectivity of this assay overcome the problems suffered by the commonly used modified Griess assays for nitrite determination. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Ruthenium(V) oxides from low-temperature hydrothermal synthesis

    Hiley, Craig I.; Walton, Richard I. [Department of Chemistry, University of Warwick, Coventry (United Kingdom); Lees, Martin R. [Department of Physics, University of Warwick, Coventry (United Kingdom); Fisher, Janet M.; Thompsett, David [Johnson Matthey Technology Centre, Reading (United Kingdom); Agrestini, Stefano [Max-Planck Institut, CPfS, Dresden (Germany); Smith, Ronald I. [ISIS Neutron and Muon Source, Rutherford Appleton Laboratory, Harwell Oxford, Didcot (United Kingdom)

    2014-04-22

    Low-temperature (200 C) hydrothermal synthesis of the ruthenium oxides Ca{sub 1.5}Ru{sub 2}O{sub 7}, SrRu{sub 2}O{sub 6}, and Ba{sub 2}Ru{sub 3}O{sub 9}(OH) is reported. Ca{sub 1.5}Ru{sub 2}O{sub 7} is a defective pyrochlore containing Ru{sup V/VI}; SrRu{sub 2}O{sub 6} is a layered Ru{sup V} oxide with a PbSb{sub 2}O{sub 6} structure, whilst Ba{sub 2}Ru{sub 3}O{sub 9}(OH) has a previously unreported structure type with orthorhombic symmetry solved from synchrotron X-ray and neutron powder diffraction. SrRu{sub 2}O{sub 6} exhibits unusually high-temperature magnetic order, with antiferromagnetism persisting to at least 500 K, and refinement using room temperature neutron powder diffraction data provides the magnetic structure. All three ruthenates are metastable and readily collapse to mixtures of other oxides upon heating in air at temperatures around 300-500 C, suggesting they would be difficult, if not impossible, to isolate under conventional high-temperature solid-state synthesis conditions. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  6. Placental transfer of ruthenium in rat and guinea-pig

    Levack, V.M.; Pottinger, H.; Harrison, J.D.

    1994-01-01

    Ruthenium-106 in citrate solution was administered intravenously to rat at different stages of pregnancy and to guinea-pig either before conception or in late pregnancy. The results for rat showed that retention in the embryo/foetus measured at 3-5 days after administration increased from about 0.0002% of injected activity per embryo/foetus on day 12 of gestation to about 0.05% at birth. The relative concentrations of 106 Ru in embryo/foetus and mother (C f /C m ratio) were about 0.1 in each case. Concentrations in the yolk sac on day 12 were about 1% g -1 compared with 0.01% g -1 kin the foetus/ Retention in the guinea-pig foetus in late gestation at 7 days after administration (days 50-57) was about 0.2% injected activity per foetus, corresponding to a C f /C m = 0.2. Retention in each foetoplacental unit was 2% of injected 106 Ru with 50% in the yolk sac, 35% in the placenta and 10% in the foetus. For administration 4 weeks prior to conception, the level of 106 Ru retained in the foetus on day 57 of gestation was two orders of magnitude lower than after short-term administration, with a C f /C m about 0.004. (author)

  7. Macromolecules containing bipyridine and terpyridine metal complexes: towards metallo-supramolecular polymers

    Schubert, U.S.; Eschbaumer, C.

    2002-01-01

    The ability of a broad range of N-heterocycles to act as very effective and stable complexation agents for several transition metal ions, such as cobalt(II), copper(II), nickel(II), and ruthenium(II), has long been known in analytical chemistry. This behavior was later utilized in supramolecular

  8. Stereodivergent-at-metal synthesis of [60]fullerene hybrids

    Marco-Martinez, Juan; Vidal, Sara; Fernandez, Israel; Filippone, Salvatore [Departamento de Quimica Organica I, Facultad de Ciencias Quimicas, Universidad Complutense de Madrid (Spain); Martin, Nazario [Departamento de Quimica Organica I, Facultad de Ciencias Quimicas, Universidad Complutense de Madrid (Spain); IMDEA-Nanociencia, C/Faraday, Universidad Autonoma de Madrid (Spain)

    2017-02-13

    Chiral fullerene-metal hybrids with complete control over the four stereogenic centers, including the absolute configuration of the metal atom, have been synthesized for the first time. The stereochemistry of the four chiral centers formed during [60]fullerene functionalization is the result of both the chiral catalysts employed and the diastereoselective addition of the metal complexes used (iridium, rhodium, or ruthenium). DFT calculations underpin the observed configurational stability at the metal center, which does not undergo an epimerization process. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Searches for discrete symmetries violation in ortho-positronium decay using the J-PET detector

    Kamińska Daria

    2015-12-01

    Full Text Available In this paper, we present prospects for using the Jagiellonian positron emission tomograph (J-PET detector to search for discrete symmetries violations in a purely leptonic system of the positronium atom. We discuss tests of CP and CPT symmetries by means of ortho-positronium decays into three photons. No zero expectation values for chosen correlations between ortho-positronium spin and momentum vectors of photons would imply the existence of physics phenomena beyond the standard model. Previous measurements resulted in violation amplitude parameters for CP and CPT symmetries consistent with zero, with an uncertainty of about 10−3. The J-PET detector allows to determine those values with better precision, thanks to the unique time and angular resolution combined with a high geometrical acceptance. Achieving the aforementioned is possible because of the application of polymer scintillators instead of crystals as detectors of annihilation quanta.

  10. Anomalous ortho-para conversion of solid hydrogen in constrained geometries

    Rall, M.; Brison, J.P.; Sullivan, N.S.

    1991-01-01

    Using cw NMR techniques, we have measured the ortho-para conversion of solid hydrogen constrained to the interior of the molecular cages of zeolite. The conversion observed in the constrained geometry is very different from that of bulk solid hydrogen. Two distinct conversion rates were observed for short and long times. An apparently bimolecular conversion rate of 0.43% h -1 (one-fourth of the bulk value) dominates during the first 500 h, and the rate then increases to 2.2% h -1 . The initial slow rate is explained in terms of a reduced number of nearest neighbors and possible wall effects, and the fast rate is attributed to the formation of small ortho-H 2 Rclusters at later times. Surface effects due to magnetic impurities do not appear to determine the conversion rate in the samples studied

  11. Level population and para/ortho ratio of fluorescent H2 in NGC 2023

    Hasegawa, T.; Ohishi, M.; Gatley, I.; Garden, R.P.; Brand, P.W.J.L.; Edinburgh Royal Observatory, England; Edinburgh Univ., Scotland)

    1987-01-01

    Observations of NGC 2023 and of peak 1 of Ori KL, obtained at 2.03-2.39 microns using the circular variable filter and a Fabry-Perot interferometer (spectral resolution 100 km/s) on the 3.8-m UKIRT on December 28-29, 1985, are reported. The data are presented in tables and graphs and characterized. Ten lines of vibrationally excited H2, indicating vibrational temperature Tv = 3600 K and rotational temperature Tr = 900-1500 K, are observed, and the para/ortho ratio is estimated as 1/(1.4-2.0). The corresponding values for Ori KL are found to be Tr = Tv = 1600-3300 K and para/ortho = 1/3. 20 references

  12. A DFT study of permanganate oxidation of toluene and its ortho-nitroderivatives.

    Adamczyk, Paweł; Wijker, Reto S; Hofstetter, Thomas B; Paneth, Piotr

    2014-02-01

    Calculations of alternative oxidation pathways of toluene and its ortho-substituted nitro derivatives by permanganate anion have been performed. The competition between methyl group and ring oxidation has been addressed. Acceptable results have been obtained using IEFPCM/B3LYP/6-31+G(d,p) calculations with zero-point (ZPC) and thermal corrections, as validated by comparison with the experimental data. It has been shown that ring oxidation reactions proceed via relatively early transition states that become quite unsymmetrical for reactions involving ortho-nitrosubstituted derivatives. Transition states for the hydrogen atom abstraction reactions, on the other hand, are late. All favored reactions are characterized by the Gibbs free energy of activation, ΔG(≠), of about 25 kcal mol(-1). Methyl group oxidations are exothermic by about 20 kcal mol(-1) while ring oxidations are around thermoneutrality.

  13. Polarization and molar volumes of ortho- and para-deuterium solutions

    Milenko, Yu.Ya.; Sibileva, R.M.

    1976-01-01

    The dielectric constant of liquid solutions of ortho-and para-deuterium is measured over the range of 2.2-91% p-D 2 from 18.7 to 20.4deg K. Data on polarization and molar volumes are obtained for the whole (0-100%) concentration range. Corrected summary to paper [2] is also listed: dielectric constant of ortho- and para-hydrogen liquid solution is measured within a concentration range of 0-97% of o-molecules at 14-20.4deg K. It is established that dependence of the Clausius-Mossotti function for o-p-hydrogen solutions of o-p-composition is linear. Molar volumes of the o-p-mixtures are calculated. The excessive molar volumes are found, positive deviation from additivity, 0.15% is established

  14. An antibacterial ortho-quinone diterpenoid and its derivatives from Caryopteris mongolica.

    Saruul, Erdenebileg; Murata, Toshihiro; Selenge, Erdenechimeg; Sasaki, Kenroh; Yoshizaki, Fumihiko; Batkhuu, Javzan

    2015-06-15

    To identify antibacterial components in traditional Mongolian medicinal plant Caryopteris mongolica, an ortho-quinone abietane caryopteron A (1) and three its derivatives caryopteron B-D (2-4) were isolated from the roots of the plant together with three known abietanes demethylcryptojaponol (5), 6α-hydroxydemethyl cryptojaponol (6), and 14-deoxycoleon U (7). The chemical structures of these abietane derivatives were elucidated on the basis of spectroscopic data. Compounds 1-4 had C-13 methylcyclopropane substructures, and 2-4 had a hexanedioic anhydride ring C instead of ortho-quinone in 1. The stereochemistry of these compound was assumed from NOE spectra and ECD Cotton effects. Compounds 1 and 5-7 showed antibacterial activities against the Gram-positive bacteria Staphylococcus aureus, Staphylococcus epidermidis, Enterococcus faecalis, and Micrococcus luteus, being 1 the more potent. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. Phase transition and intramolecular hydrogen bonding in nitro derivatives of ortho-hydroxy acetophenones

    Filarowski, A.; Kochel, A.; Koll, A.; Bator, G.; Mukherjee, S.

    2006-03-01

    The crystal structures of two ortho-hydroxy aryl ketones (5-chloro-3-nitro-2-hydroxyacetophenone, 5-methyl-3-nitro-2-hydroxyacetophenone and the complex 5-chloro-3-nitro-2-hydroxyacetophenone with 2-aminobenzoic acid (anthranilic acid)) were determined by X-ray diffraction. The existence of an intramolecular hydrogen bond of enol character between the hydroxyl and acetyl groups was found by the X-ray method. The enol character was also confirmed by DFT (B3LYP/6-31+G(d,p)) calculations. A phase transition was found at 138 K in 5-chloro-3-nitro-2-hydroxyacetophenone. This phase transition was investigated by differential scanning calorimetry (DSC), dilatometry, and the dielectric method. A study of the nitro-group dynamics in the ortho-hydroxy acetophenones was carried out with DFT (B3LYP/6-31+G(d,p)) calculations.

  16. Electron transfer reactions of ruthenium(II) complexes with polyphenolic acids in micelles

    Rajeswari, Angusamy [School of Chemistry, Madurai Kamaraj University, Madurai 625 021 (India); Department of Chemistry, Fatima College, Madurai 625 018 (India); Ramdass, Arumugam [School of Chemistry, Madurai Kamaraj University, Madurai 625 021 (India); Research Department of Chemistry, Aditanar College of Arts and Science, Tiruchendur 628 216 (India); Muthu Mareeswaran, Paulpandian [School of Chemistry, Madurai Kamaraj University, Madurai 625 021 (India); Department of Industrial Chemistry, Alagappa University, Karaikudi 630 003 (India); Rajagopal, Seenivasan, E-mail: rajagopalseenivasan@yahoo.com [School of Chemistry, Madurai Kamaraj University, Madurai 625 021 (India)

    2016-02-15

    The electron transfer in a microhetrogeneous system is a perfect mimic of biological electron transfer. The electron transfer between biologically important phenolic acids and ruthenium (II) complexes is systematically studied in the presence of anionic and cationic micelles. The photophysical properties of these ruthenium (II) complexes with anionic and cationic micelles and their binding abilities with these two type of micelles are also studies using absorption, emission and excited state lifetime spectral techniques. Pseudophase Ion Exchange (PIE) Model is applied to derive mechanism of electron transfer in two types of micelles. - Highlights: • Effect of microhetrogeneous system is studied using ruthenium (II) complexes and gallic acid is studied. • Pseudophase Ion exchange model is applied to derive the mechanism. • Binding constants are in the range of 10{sup 2}–10{sup 4} M{sup −1}.

  17. Stable tracer investigations in humans for assessing the biokinetics of ruthenium and zirconium radionuclides

    Veronese, I.; Cantone, M.C.; Giussani, A.; Maggioni, T.; Birattari, C.; Bondardi, M.; Groppi, F.; Garlaschelli, I.; Werner, E.; Roth, P.; Hoellriegl, V.; Louvat, P.; Felgenhauer, N.; Zilker, Th.

    2003-01-01

    The interest in the biokinetics of ruthenium and zirconium in humans is justified by the potential radiological risk represented by their radionuclides. Only a few data related to the biokinetics of ruthenium and zirconium in humans are available and, accordingly, the biokinetic models currently recommended by the ICRP for these elements are mainly based on data from animal experiments. The use of stable isotopes as tracers, coupled with a proper analytical technique (nuclear activation analysis with protons) for their determination in biological samples, represents an ethically acceptable methodology for biokinetic investigations, being free from any radiation risk for the volunteer subjects. In this work, the results obtained in eight biokinetic investigations for ruthenium, conducted on a total of three healthy volunteers, and six for zirconium, performed on a total of three subjects, are presented and compared to the predictions of the ICRP models. (author)

  18. Amorphous carbon nanofibres inducing high specific capacitance of deposited hydrous ruthenium oxide

    Barranco, V.; Pico, F.; Ibanez, J.; Lillo-Rodenas, M.A.; Linares-Solano, A.; Kimura, M.; Oya, A.; Rojas, R.M.; Amarilla, J.M.; Rojo, J.M.

    2009-01-01

    Composites consisting of ruthenium oxide particles deposited on amorphous carbon nanofibres are prepared by a repetitive impregnation procedure. The choice of amorphous carbon nanofibres as support of amorphous ruthenium oxide leads to composites in which the deposited oxide consists of aggregates of extremely small primary particles (1-1.5 nm-size) and showing high porosity (specific surface area of 450 m 2 g -1 ). This special deposition of the oxide seems to favour: (i) high oxide capacitance (1000 Fg -1 ) at high oxide loadings (up to 20 wt%) and (ii) high capacitance retention (ca. 80% from the initial oxide capacitance) at high current densities (200 mA cm -2 ). Amorphous carbon nanofibres are suitable supports for amorphous ruthenium oxide and perhaps for other amorphous oxides acting as active electrode materials.

  19. Estimation of very low concentrations of Ruthenium by spectrophotometric method using barbituric acid as complexing agent

    Ramakrishna Reddy, S.; Srinivasan, R.; Mallika, C.; Kamachi Mudali, U.; Natarajan, R.

    2012-01-01

    Spectrophotometric method employing numerous chromogenic reagents like thiourea, 1,10-phenanthroline, thiocyanate and tropolone is reported in the literature for the estimation of very low concentrations of Ru. A sensitive spectrophotometric method has been developed for the determination of ruthenium in the concentration range 1.5 to 6.5 ppm in the present work. This method is based on the reaction of ruthenium with barbituric acid to produce ruthenium(ll)tris-violurate, (Ru(H 2 Va) 3 ) -1 complex which gives a stable deep-red coloured solution. The maximum absorption of the complex is at 491 nm due to the inverted t 2g → Π(L-L ligand) electron - transfer transition. The molar absorptivity of the coloured species is 9,851 dm 3 mol -1 cm -1

  20. The first organocatalytic, ortho-regioselective inverse-electron-demand hetero-Diels-Alder reaction.

    Hejmanowska, Joanna; Jasiński, Marcin; Wojciechowski, Jakub; Mlostoń, Grzegorz; Albrecht, Łukasz

    2017-10-17

    The development of the unprecedented ortho-regioselective inverse-electron-demand hetero-Diels-Alder (IEDHDA) reaction is described. It has been demonstrated that by proper choice of reactants and reaction conditions the inverse-electron-demand hetero-Diels-Alder cycloaddition can be realized with unprecedented regioselectivity arising from the reaction between the terminal carbon atom of the dienophile and the heteroatom of the heterodiene.

  1. Mechanisms of Decreased Moisture Uptake in ortho- Methylated Di(Cyanate Esters)

    2014-10-01

    the lower dry TG of the ortho- methylated networks. The measured “knock down” depends on plasticization of the networks by any moisture remaining...The addition of catalyst results in a higher degree of conversion, but generally decreases the dry TG at full conversion due to plasticization of...of DBTDL, however, results in severe damage to the samples on exposure to hot water, with networks 3 and 4 undergoing disintegration during the 96

  2. Theoretical investigation of tautomeric equilibrium in ortho-hydroxy phenyl Schiff bases

    Kluba, M.; Lipkowski, P.; Filarowski, A.

    2008-10-01

    This Letter presents a study of the tautomeric equilibrium in ortho-hydroxy phenyl Schiff bases. The influence of substitution and solvent (simulated by the self-consistent reaction field model, SCRF) on the energy barrier of the transition state and on proton transfer is investigated. Dependencies of the HOMA and HOSE aromaticity indices on the molecular, transition state, and proton transfer forms were obtained. The state of chelate chain and phenyl ring aromaticity depending on the tautomeric equilibrium is studied.

  3. The Photocatalytic Removal of Ortho Chlorophenol from Aqueous Solution Using Modified Fly Ash - Titanium Dioxide

    Mohamad Malakootian

    2016-05-01

    Full Text Available The photocatalytic process is a useful method for the effective removal of phenolic compounds. Conducted in the spring‒summer 2013 at the Engineering Research Center for Environmental Health, Kerman University of Medical Sciences, this experimental study used a modified fly ash‒TiO2 mixture to enhance the photocatalytic removal efficiency of ortho-chlorophenol. Fly ash obatined from the Thermal Power Plant in Zarand, Kerman, was initially washed with sulfuric acid before being oxidized with potassium permanganate. The mixture of modified fly ash and TiO2 was then used for the removal of ortho-chlorophenol in the presence of UV light and the factors involved in the removal process were optimized. It was found that the ortho-chlorophenol removal efficiency recorded by the mixture of modified fly ash and TiO2 was higher than that by each of the modified fly ash or TiO2/UV alone. It was, further, observed that removal efficiency with a modified fly ash to TiO2 ratio of 3:1 rose to 98.8% under optimum conditions (i.e., pH: 2; contact time: 2 h; room temperature (29±2˚C, and a catalyst dose of 0.6 g. The ortho-chlorophenol removal efficiency in real wastewater from the Coal Wash Plant in Zarand was recorded at 88.4%. Based on the results obtained from simultaneous use of modified fly ash and TiO2, the proposed method may be recommended for industrial applications.

  4. Gold-catalyzed alkylation of silyl enol ethers with ortho-alkynylbenzoic acid esters

    Yoshinori Yamamoto

    2011-05-01

    Full Text Available Unprecedented alkylation of silyl enol ethers has been developed by the use of ortho-alkynylbenzoic acid alkyl esters as alkylating agents in the presence of a gold catalyst. The reaction probably proceeds through the gold-induced in situ construction of leaving groups and subsequent nucleophilic attack on the silyl enol ethers. The generated leaving compound abstracts a proton to regenerate the silyl enol ether structure.

  5. Catalytical conversion from ortho-H2 to para-H2

    Corat, E.J.

    1984-01-01

    The classical theory of ortho to para-H 2 conversion is discussed, considering the catalytical action of an inhomogeneous magnetic field on a surface with magnetic particles. In particular, the use of charcoal as a catalyst at low temperatures (77 0 K) is considered and some results are presented. The development of a sensor for the determination of para-H 2 concentration in H 2 gas is studied. Experimental results with this sensor are also shown. (Author) [pt

  6. Functional Evaluation of Modified T Pouch as Ileal Neo bladder Ortho topic Reservoir

    Hammouda, H.M.

    2004-01-01

    We report on the functional results of ortho topic modified T pouch ileal neo bladder, incorporating serous- lined extra mural ileal anti reflux technique for urinary diversion after radical cystectomy. Material and Methods: From September 1998 through November 2001,42 patients of mean age 49 years (range 45-54) having invasive bladder carcinoma underwent radical cystectomy and ortho topic ileal neo bladder urinary diversion, the modified T pouch. Thirty-three patients were males while the remaining 9 were females. The mean follow up was 24 months (range 18-42). Preoperative unior bilateral ureteral dilatation was noted in 13/42 (30.9%) patients). Follow up included clinical examination, laboratory, radiological and uro dynamic investigations. Early postoperative complications were recorded in 3 cases, that were managed conservatively. Day and night continence were achieved in 34/42 (81 %) and 29/42 (69%) patients, night enuresis in 2 (4.8%),while satisfactory day and night continence were noted, respectively. Upper urinary tract (UUT) remained unchanged or improved in all cases. No need for clean intermittent catherization (CIC). No evidence of reflux was detected. Pressure at maximum capacity (average 17 cm H 2 O at 600 ml). Mean flow rate was 17.6 ml/sec (range 15-24). Pelvic cancer recurrence was recorded in 5 patients at mean 24 months, respectively. Modified T pouch has an excellent functional criteria as an ortho topic ileal neo bladder reservoir. It is absolutely indicated in short and/or massively dilated ureter

  7. OrthoANI: An improved algorithm and software for calculating average nucleotide identity.

    Lee, Imchang; Ouk Kim, Yeong; Park, Sang-Cheol; Chun, Jongsik

    2016-02-01

    Species demarcation in Bacteria and Archaea is mainly based on overall genome relatedness, which serves a framework for modern microbiology. Current practice for obtaining these measures between two strains is shifting from experimentally determined similarity obtained by DNA-DNA hybridization (DDH) to genome-sequence-based similarity. Average nucleotide identity (ANI) is a simple algorithm that mimics DDH. Like DDH, ANI values between two genome sequences may be different from each other when reciprocal calculations are compared. We compared 63 690 pairs of genome sequences and found that the differences in reciprocal ANI values are significantly high, exceeding 1 % in some cases. To resolve this problem of not being symmetrical, a new algorithm, named OrthoANI, was developed to accommodate the concept of orthology for which both genome sequences were fragmented and only orthologous fragment pairs taken into consideration for calculating nucleotide identities. OrthoANI is highly correlated with ANI (using BLASTn) and the former showed approximately 0.1 % higher values than the latter. In conclusion, OrthoANI provides a more robust and faster means of calculating average nucleotide identity for taxonomic purposes. The standalone software tools are freely available at http://www.ezbiocloud.net/sw/oat.

  8. Dielectric property of NiTiO3 doped substituted ortho-chloropolyaniline composites

    Mohana Lakshmi

    2013-11-01

    Full Text Available Ortho-chloropolyaniline (OCP-NiTiO3 composites have been synthesized via in-situ polymerization of ortho-chloroaniline with various weight percentages of NiTiO3. Fourier Transform Infrared spectroscopic studies of Ortho-chloropolyaniline and its composites indicated the formation of composites as a result of Vander Waal's interaction between OCP and NiTiO3 particles. Surface morphology of OCP and OCP-NiTiO3 composites were studied using Scanning Electron Microscope (SEM. The SEM micrographs indicated a modified morphology after the composite formation. Dielectric properties and electric modulus of OCP and OCP-NiTiO3 composites have been investigated in the frequency range of 50 Hz – 5 MHz. It has been noticed that electrical resistance decreases with increase in weight percentage of NiTiO3 particles in polymer matrix as well as with applied frequency. The display of semicircular arcs in Cole-Cole plots indicates the formation of series resistor and capacitor in network causing a decrease in the relaxation time and as a result conductivity enhances in these composites. The facile and cost effective synthesis process and excellent dielectric and conductivity response of these materials makes them promising materials for practical applications.

  9. The ortho:para ratio of H{sub 3}{sup +} in laboratory and astrophysical plasmas

    Crabtree, Kyle N.; Indriolo, Nick; Kreckel, Holger; McCall, Benjamin J. [University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States)

    2015-01-22

    The discovery of H{sub 3}{sup +} in the diffuse interstellar medium has dramatically changed our view of the cosmic-ray ionization rate in diffuse molecular clouds. However, another surprise has been that the ortho:para ratio of H{sub 3}{sup +} in these clouds is inconsistent with the temperature derived from the excitation of H{sub 2}, the dominant species in these clouds. In an effort to understand this discrepancy, we have embarked on an experimental program to measure the nuclear spin dependence of the dissociative electron recombination rate of H{sub 3}{sup +} using the CRYRING and TSR ion storage rings. We have also performed the first measurements of the reaction H{sub 3}{sup +}+H{sub 2}→H{sub 2}+H{sub 3}{sup +} below room temperature. This reaction is likely the most common bimolecular reaction in the universe, and plays an important role in interconverting ortho- and para-H{sub 3}{sup +}. Finally, we have constructed a steady-state chemical model for diffuse clouds, which takes into account the spin-dependence of the formation of H{sub 3}{sup +}, its electron recombination, and its reaction with H{sub 2}. We find that the ortho:para ratio of H{sub 3}{sup +} in diffuse clouds is likely governed by a competition between dissociative recombination and thermalization by reactive collisions.

  10. Dye sensitized photovoltaic cells: Attaching conjugated polymers to zwitterionic ruthenium dyes

    Krebs, Frederik C; Biancardo, M.

    2006-01-01

    The synthesis of a zwitterionic ruthenium dye that binds to anatase surfaces and has a built-in functionality that allows for the attachment of a conjugated polymer chain is presented. The system was found to adsorb on the surface of anatase anchored by the ruthenium dye. Two types of devices were...... prepared: standard photoelectrochemical (PEC) solar cells and polymer solar cells. The PEC solar cells employed a sandwich geometry between TiO2 nanoporous photoanodes and Pt counter electrodes using LiI/I-2 in CH3CN as an electrolyte. The polymer solar cells employed planar anatase electrodes...

  11. Ruthenium phosphine complexes as catalysts for alternating co-polymerization of ethylene and CO

    Gusev, O.V.; Kal'sin, A.M.; Peganov, T.A.; Petrovskij, P.V.; Belov, G.P.; Novikova, E.V.

    2000-01-01

    Ruthenium (2) complexes, [Ru(dppe) 2 (OTs) 2 ] and [Ru(PhP(CH 2 CH 2 CH 2 PPh 2 ) 2 )(OTs) 2 ], where dppe (diphenylphosphino)ethane; OTs = tosylate, were synthesized with the yield of 67 and 76%, respectively, and characterized by 31 P NMR. The properties of the above complexes as catalysts of alternating co-polymerization of ethylene and carbon monoxide were studied. A considerable increase in catalytic activity of the complexes was established in the presence of trifluoroacetic acid and 1,4-benzoquinone. These compounds are the first example of ruthenium complexes that catalyse co-polymerization of ethylene and CO [ru

  12. Behaviour of ruthenium in the case of shutdown of the cooling system of HLLW storage tanks

    Philippe, M.; Gue, J.P.; Mercier, J.P.

    1990-12-01

    The consequences of the failure of the cooling system of fission product storage tanks over a variable period were investigated as part of the safety analysis of the La Hague spent fuel reprocessing plant. Due to the considerable heat release, induced by the fission products, a prolonged shutdown of the tank cooling system could cause the progressive evaporation of the solutions to dryness, and culminate in the formation of volatile species of ruthenium and their release in the tank venting circuit. To determine the fraction of ruthenium likely to be transferred from the storage tanks in volatile or aerosol form during the failure, evaporation tests were conducted by evaporating samples of actual nitric acid solutions of fission products, obtained on the laboratory scale after the reprocessing of several kilograms of MOX fuels irradiated to 30.000 MW day ·t -1 . A distillation apparatus was designed to operate with small-volume solution samples, reproducing the heating conditions existing in the reprocessing plant within a storage tank for fission products. The main conclusions drawn from these experiments are as follows: - ruthenium is only volatilized in the final phase of evaporation, just before desiccation, - for a final temperature limited to 160 deg. C, the total fraction of volatilized ruthenium reaches 12%, - in the presence of H 2 O, HNO 3 , NO x and O 2 , the volatilized ruthenium recombines mainly in the form of ruthenium nitrosyl nitrates, or decomposes into ruthenium oxide (probably RuO 2 ) on the walls of the apparatus. Assuming a heating power density of 10 W/liter of concentrate, and a perfectly adiabatic storage system, the minimum time required to reach dryness can be estimated at 90 h, allowing substantial time to take action to restore a cooling source. It is probable that, in an industrial storage tank, the heat losses from the tank and the offgas discharge ducts will cause recondensation and internal reflux, which will commensurately delay

  13. General synthesis of (salen)ruthenium(III) complexes via N...N coupling of (salen)ruthenium(VI) nitrides.

    Man, Wai-Lun; Kwong, Hoi-Ki; Lam, William W Y; Xiang, Jing; Wong, Tsz-Wing; Lam, Wing-Hong; Wong, Wing-Tak; Peng, Shie-Ming; Lau, Tai-Chu

    2008-07-07

    Reaction of [Ru (VI)(N)(L (1))(MeOH)] (+) (L (1) = N, N'-bis(salicylidene)- o-cyclohexylenediamine dianion) with excess pyridine in CH 3CN produces [Ru (III)(L (1))(py) 2] (+) and N 2. The proposed mechanism involves initial equilibrium formation of [Ru (VI)(N)(L (1))(py)] (+), which undergoes rapid N...N coupling to produce [(py)(L (1))Ru (III) N N-Ru (III)(L (1))(py)] (2+); this is followed by pyridine substituion to give the final product. This ligand-induced N...N coupling of Ru (VI)N is utilized in the preparation of a series of new ruthenium(III) salen complexes, [Ru (III)(L)(X) 2] (+/-) (L = salen ligand; X = H 2O, 1-MeIm, py, Me 2SO, PhNH 2, ( t )BuNH 2, Cl (-) or CN (-)). The structures of [Ru (III)(L (1))(NH 2Ph) 2](PF 6) ( 6), K[Ru (III)(L (1))(CN) 2] ( 9), [Ru (III)(L (2))(NCCH 3) 2][Au (I)(CN) 2] ( 11) (L (2) = N, N'-bis(salicylidene)- o-phenylenediamine dianion) and [N ( n )Bu 4][Ru (III)(L (3))Cl 2] ( 12) (L (3) = N, N'-bis(salicylidene)ethylenediamine dianion) have been determined by X-ray crystallography.

  14. Preparation of Different Substitued Polypyridine Ligands, Ruthenium(II)-Bridged Complexes and Spectoscopıc Studies.

    Obali, Aslihan Yilmaz; Ucan, Halil Ismet

    2016-09-01

    Novel different substitued polypyridine ligands 4-((4-(1H-imidazo[4,5-f][1,10]phenanthroline-2-yl)phenoxy)methyl)benzaldehyde (BA-PPY), (E)-N-(4-((4-(1H-imidazo[4,5-f][1,10]phenanthroline-2-yl)phenoxy)methyl)benzylidene)-pyrene-4-amine (PR-PPY), (E)-N-(4-((4-(1H-imidazo[4,5-f][1,10] phenanthroline-2-yl)phenoxy)methyl)benzylidene)-1,10-phenanthroline-5amine (FN-PPY), 2-(4-(bromomethyl)phenyl)-1H-imidazo[4,5-f][1,10] phenanthroline (BR-PPY), 2-(4-(azidomethyl)phenyl)-1H-imidazo[4,5-f][1,10]phenanthroline (N3-PPY) and triazole containing polypyridine ligand 3,4-bis[(4-(metoxy)-1,2,3-triazole)1-methylphenyl)-1H-imidazo[4,5-f][1,10]phenanthroline)] benzaldehyde (BA-DIPPY) and Ruthenium(II) complexes were synthesized and characterized. Their photopysical properties were investigated. The complexes RuP(PR-PPY), RuB(PR-PPY, RuP(FN-PPY) and RuB(FN-PPY) exhibited a broad absorption bands at 485, 475, 476, and 453 nm, respectively, assignable to the spin-allowed MLCT (dπ-π*) transition. The emission maxima of the pyrene-appended polypyridine ligand PR-PPY was observed at λems = 616 nm and the phenanthroline-appended polypyridine ligand FN-PPY was observed at λems = 668 nm. And the emission maxima of the complexes RuP(PR-PPY), RuB(PR-PPY), RuP(FN-PPY) and RuB(FN-PPY) were observed at λems = 646, 646, 685 and 685 nm, respectively. As seen in fluorescence spectra, the fluorescence intensities of the ligands are higher than their metal complexes. This is because of quenching effect of Ruthenium(II) metal on chromophore groups.

  15. Ruthenium complexes containing 2-(2-nitrosoaryl)pyridine: structural, spectroscopic, and theoretical studies.

    Chan, Siu-Chung; Cheung, Ho-Yuen; Wong, Chun-Yuen

    2011-11-21

    Ruthenium complexes containing 2-(2-nitrosoaryl)pyridine (ON(^)N) and tetradentate thioether 1,4,8,11-tetrathiacyclotetradecane ([14]aneS4), [Ru(ON(^)N)([14]aneS4)](2+) [ON(^)N = 2-(2-nitrosophenyl)pyridine (2a), 10-nitrosobenzo[h]quinoline (2b), 2-(2-nitroso-4-methylphenyl)pyridine, (2c), 2-(2-nitrosophenyl)-5-(trifluoromethyl)pyridine (2d)] and analogues with the 1,4,7-trithiacyclononane ([9]aneS3)/tert-butylisocyanide ligand set, [Ru(ON(^)N)([9]aneS3)(C≡N(t)Bu)](2+) (4a and 4b), have been prepared by insertion of a nitrosonium ion (NO(+)) into the Ru-aryl bond of cyclometalated ruthenium(II) complexes. The molecular structures of the ON(^)N-ligated complexes 2a and 2b reveal that (i) the ON(^)N ligands behave as bidentate chelates via the two N atoms and the bite angles are 86.84(18)-87.83(16)° and (ii) the Ru-N(NO) and N-O distances are 1.942(5)-1.948(4) and 1.235(6)-1.244(5) Å, respectively. The Ru-N(NO) and N-O distances, together with ν(N═O), suggest that the coordinated ON(^)N ligands in this work are neutral moiety (ArNO)(0) rather than monoanionic radical (ArNO)(•-) or dianion (ArNO)(2-) species. The nitrosated complexes 2a-2d show moderately intense absorptions centered at 463-484 nm [ε(max) = (5-6) × 10(3) dm(3) mol(-1) cm(-1)] and a clearly discriminable absorption shoulder around 620 nm (ε(max) = (6-9) × 10(2) dm(3) mol(-1) cm(-1)), which tails up to 800 nm. These visible absorptions are assigned as a mixing of d(Ru) → ON(^)N metal-to-ligand charge-transfer and ON(^)N intraligand transitions on the basis of time-dependent density functional theory (TD-DFT) calculations. The first reduction couples of the nitrosated complexes range from -0.53 to -0.62 V vs Cp(2)Fe(+/0), which are 1.1-1.2 V less negative than that for [Ru(bpy)([14]aneS4)](2+) (bpy = 2,2'-bipyridine). Both electrochemical data and DFT calculations suggest that the lowest unoccupied molecular orbitals of the nitrosated complexes are ON(^)N-centered. Natural population

  16. The challenges of treating high strength wastewaters: CWAO using MWNT supported ruthenium catalysts

    GarcIa, J.; Gomes, H.T.; Figueiredo, J.L.; Faria, J.L.; Garcia, J.; Serp, P.; Kalck, P.

    2005-01-01

    High strength wastewaters containing aromatic compounds are normally not efficiently treated by conventional methods, including the common biological treatment. In these cases a more sophisticated approach is necessary to attain the desired levels of purification. Catalytic wet air oxidation (CWAO) using carbon based catalysts is employed worldwide as effective pre-treatment of effluents with these characteristics. Carbon materials are preferred as active catalysts or support for preparing them due to their morphological and structural characteristics. In the last 10 years, due to a tremendous development in materials production and processing, carbon nano-structures are becoming more accessible and common widening their range of applications [1]. In this context, the scope of the present work is to illustrate a potential use of multi-walled carbon nano-tubes (MWNT) supported ruthenium catalysts for catalytic wet air oxidation of aniline polluted wastewaters. The metal was supported by incipient wetness and excess impregnation, starting from liquid solutions of three different Ru precursors. Impregnation was carried out on modified MWNT, namely on MWNT-COOH (HNO 3 modified) and MWNT-COONa (HNO 3 /Na 2 CO 3 modified). For the 1% weight Ru/MWNT catalysts, the order of activities decreased in the sequence Ru(COD)(COT)≥RuCl 3 ≥Ru(C 5 H 5 ) 2 . The conversion of aniline after 45 min of reaction was 100% for the catalyst prepared with Ru(COD)(COT). The influence of the Ru precursor, preparation method and the support surface modification was studied comparing the conversion of aniline obtained for the different prepared Ru/MWNT catalysts (Figure 1). MWNT as support material, provide a significant metal dispersion with very small Ru nanoparticles (Figure 2) being observed. This will induce an efficient surface contact between the aniline molecule and the active sites [2]. The excellent catalytic performances of Ru/MWNT are explained in terms of the high dispersion of

  17. The challenges of treating high strength wastewaters: CWAO using MWNT supported ruthenium catalysts

    GarcIa, J.; Gomes, H.T.; Figueiredo, J.L.; Faria, J.L. [Porto Univ., Lab. de Catalise e Materiais, Dept. de Engenharia Quimica, Faculdade de Engenharia (Portugal); Garcia, J. [Madrid Univ. Complutense, Grupo de Catalisis y Operaciones de Separacion, Dept. de Ingenieria Quimica, Facultad de Ciencias (Spain); Serp, P.; Kalck, P. [Ecole Nationale Superieure des Ingenieurs en Arts Chimiques et Technologiques, Lab. de Catalyse, Chimie Fine et Polymeres, 31 - Toulouse (France)

    2005-07-01

    High strength wastewaters containing aromatic compounds are normally not efficiently treated by conventional methods, including the common biological treatment. In these cases a more sophisticated approach is necessary to attain the desired levels of purification. Catalytic wet air oxidation (CWAO) using carbon based catalysts is employed worldwide as effective pre-treatment of effluents with these characteristics. Carbon materials are preferred as active catalysts or support for preparing them due to their morphological and structural characteristics. In the last 10 years, due to a tremendous development in materials production and processing, carbon nano-structures are becoming more accessible and common widening their range of applications [1]. In this context, the scope of the present work is to illustrate a potential use of multi-walled carbon nano-tubes (MWNT) supported ruthenium catalysts for catalytic wet air oxidation of aniline polluted wastewaters. The metal was supported by incipient wetness and excess impregnation, starting from liquid solutions of three different Ru precursors. Impregnation was carried out on modified MWNT, namely on MWNT-COOH (HNO{sub 3} modified) and MWNT-COONa (HNO{sub 3}/Na{sub 2}CO{sub 3} modified). For the 1% weight Ru/MWNT catalysts, the order of activities decreased in the sequence Ru(COD)(COT){>=}RuCl{sub 3}{>=}Ru(C{sub 5}H{sub 5}){sub 2}. The conversion of aniline after 45 min of reaction was 100% for the catalyst prepared with Ru(COD)(COT). The influence of the Ru precursor, preparation method and the support surface modification was studied comparing the conversion of aniline obtained for the different prepared Ru/MWNT catalysts (Figure 1). MWNT as support material, provide a significant metal dispersion with very small Ru nanoparticles (Figure 2) being observed. This will induce an efficient surface contact between the aniline molecule and the active sites [2]. The excellent catalytic performances of Ru/MWNT are explained

  18. A ruthenium anticancer compound interacts with histones and impacts differently on epigenetic and death pathways compared to cisplatin.

    Licona, Cynthia; Spaety, Marie-Elodie; Capuozzo, Antonelle; Ali, Moussa; Santamaria, Rita; Armant, Olivier; Delalande, Francois; Van Dorsselaer, Alain; Cianferani, Sarah; Spencer, John; Pfeffer, Michel; Mellitzer, Georg; Gaiddon, Christian

    2017-01-10

    Ruthenium complexes are considered as potential replacements for platinum compounds in oncotherapy. Their clinical development is handicapped by a lack of consensus on their mode of action. In this study, we identify three histones (H3.1, H2A, H2B) as possible targets for an anticancer redox organoruthenium compound (RDC11). Using purified histones, we confirmed an interaction between the ruthenium complex and histones that impacted on histone complex formation. A comparative study of the ruthenium complex versus cisplatin showed differential epigenetic modifications on histone H3 that correlated with differential expression of histone deacetylase (HDAC) genes. We then characterized the impact of these epigenetic modifications on signaling pathways employing a transcriptomic approach. Clustering analyses showed gene expression signatures specific for cisplatin (42%) and for the ruthenium complex (30%). Signaling pathway analyses pointed to specificities distinguishing the ruthenium complex from cisplatin. For instance, cisplatin triggered preferentially p53 and folate biosynthesis while the ruthenium complex induced endoplasmic reticulum stress and trans-sulfuration pathways. To further understand the role of HDACs in these regulations, we used suberanilohydroxamic acid (SAHA) and showed that it synergized with cisplatin cytotoxicity while antagonizing the ruthenium complex activity. This study provides critical information for the characterization of signaling pathways differentiating both compounds, in particular, by the identification of a non-DNA direct target for an organoruthenium complex.

  19. In vitro evaluation of ruthenium complexes for photodynamic therapy.

    Li, Wenna; Xie, Qiang; Lai, Linglin; Mo, Zhentao; Peng, Xiaofang; Leng, Ennian; Zhang, Dandan; Sun, Hongxia; Li, Yiqi; Mei, Wenjie; Gao, Shuying

    2017-06-01

    Photodynamic therapy (PDT) is a promising anti-tumor treatment strategy. Photosensitizer is one of the most important components of PDT. In this work, the anticancer activities of PDT mediated by six new ruthenium porphyrin complexes were screened. The mechanisms of the most efficacious candidate were investigated. Photocytotoxicity of the six porphyrins was tested. The most promising complex, Rup-03, was further investigated using Geimsa staining, which indirectly detects reactive oxygen species (ROS) and subcellular localization. Mitochondrial membrane potential (MMP), cell apoptosis, DNA fragmentation, c-Myc gene expression, and telomerase activities were also assayed. Rup-03 and Rup-04 had the lowest IC 50 values. Rup-03 had an IC 50 value of 29.5±2.3μM in HepG2 cells and 59.0±6.1μM in RAW264.7 cells, while Rup-04 had an IC 50 value of 40.0±3.8μM in SGC-7901 cells. The complexes also induced cellular morphological changes and impaired cellular ability to scavenge ROS, and accumulated preferentially in mitochondria and endoplasmic reticulum. Rup-03 reduced MMP levels, induced apoptosis, and repressed both c-Myc mRNA expression and telomerase activity in HepG2 cells. Among six candidates, Rup-03-mediated PDT is most effective against HepG2 and RAW264.7, with a similar efficacy as that of Rup-04-mediated PDT against SGC-7901 cells. Repression of ROS scavenging activities and c-Myc expression, which mediated DNA damage-induced cell apoptosis and repression of telomerase activity, respectively, were found to be involved in the anticancer mechanisms of Rup-03. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. {sup 106}Ruthenium Plaque Therapy (RPT) for Retinoblastoma

    Murakami, Naoya, E-mail: namuraka@ncc.go.jp [Department of Radiation Oncology, National Cancer Center Hospital, Tokyo (Japan); Suzuki, Shigenobu [Department of Ophthalmic Oncology, National Cancer Center Hospital, Tokyo (Japan); Ito, Yoshinori [Department of Radiation Oncology, National Cancer Center Hospital, Tokyo (Japan); Yoshimura, Ryoichi [Department of Diagnostic Radiology and Oncology, Head and Neck Reconstruction Division, Graduate School, Tokyo Medical and Dental University, Tokyo (Japan); Inaba, Koji; Kuroda, Yuki; Morota, Madoka; Mayahara, Hiroshi; Sakudo, Mototake; Wakita, Akihisa; Okamoto, Hiroyuki; Sumi, Minako; Kagami, Yoshikazu [Department of Radiation Oncology, National Cancer Center Hospital, Tokyo (Japan); Nakagawa, Keiichi; Ohtomo, Kuni [Department of Radiology, University of Tokyo Hospital, Tokyo (Japan); Itami, Jun [Department of Radiation Oncology, National Cancer Center Hospital, Tokyo (Japan)

    2012-09-01

    Purpose: To evaluate the effectiveness of episcleral {sup 106}ruthenium plaque therapy (RPT) in the management of retinoblastoma. Methods and Materials: One hundred one RPTs were retrospectively analyzed that were performed in 90 eyes of 85 patients with retinoblastoma at National Cancer Center Hospital between 1998 and 2008. Each RPT had a corresponding tumor and 101 tumors were considered in the analysis of local control. Median follow-up length was 72.8 months. Median patient age at the RPT was 28 months. Median prescribed doses at reference depth and outer surface of the sclera were 47.4 Gy and 162.3 Gy, respectively. Results: Local control rate (LCR) and ocular retention rate (ORR) at 2 years were 33.7% and 58.7%, respectively. Unilateral disease, International Classification of Retinoblastoma group C or more advanced at the first presentation or at the time of RPT, vitreous and/or subretinal seeding, tumor size greater than 5 disc diameter (DD), reference depth greater than 5 mm, dose rate at reference depth lower than 0.7 Gy/hour, dose at the reference depth lower than 35 Gy, and (biologically effective dose with an {alpha}/{beta} ratio of 10 Gy) at the reference depth lower than 40 Gy{sub 10} were associated with unfavorable LCR. Two patients died of metastatic disease. Radiation complications included retinal detachment in 12 eyes (13.3%), proliferative retinopathy in 6 (6.7%), rubeosis iris in 2 (2.2%), and posterior subcapsular cataract in 23 (25.6%). Conclusion: RPT is an effective eye-preserving treatment for retinoblastoma.

  1. Behavior of ruthenium, cesium and antimony during simulated HLLW vitrification

    Klein, M.; Weyers, C.; Goossens, W.R.A.

    1985-01-01

    The behavior of ruthenium, cesium, and antimony during the vitrification of simulated high-level radioactive liquid wastes (HLLW) in a liquid fed melter was studied on a laboratory scale and on a semi-pilot scale. In the laboratory melter of a 2.5 kg capacity, a series of tests with the simulate traced with 103 Ru, 134 Cs and 124 Sb, has shown that the Ru and Cs losses to the melter effluent are generally higher than 10% whereas the antimony losses remain lower than 0.4%. A wet purification system comprising in series, a dust scrubber, a condenser, an ejector venturi and an NOx washing column retains most of the activity present in the off-gas so that the release fractions for Ru at the absolute filter inlet ranges between 5.10 -3 to 5.10 -5 % of the Ru fed, for Cs the corresponding release fraction ranges between 3.10 -3 to 10 -4 % and for Sb the release fraction ranges between 1.7 10 -4 to 1.7 10 -5 %. The same experiments were performed at a throughput of 1 to 2 1 h -1 of simulated solution in the semi-pilot scale unit RUFUS. The RUFUS unit comprises a glass melter with a 50 kg molten glass capacity and the wet purification train comprises in series a dust scrubber, a condenser, an ejector venturi and an NOx washing column. The tracer tests were restricted to 103 Ru and 134 Cs since the laboratory tests had shown that the antimony losses were very low. The results of the tests are presented

  2. Reaction mechanisms of ruthenium tetroxide mediated oxidations of organic compounds

    Froehaug, Astrid Elisabeth

    1995-12-31

    This thesis reports a study of the mechanism of ruthenium tetroxide mediated oxidations of saturated hydrocarbons, ethers, alkenes and alcohols. Several methods were used. The RuO{sub 4}-mediated oxidations of adamantane and cis-decalin were studied in CCl{sub 4}-CH{sub 3}CN-H{sub 2}O and in acetone-water. The rate of reaction was found to be moderately influenced by the polarity of the solvent. Solvent properties other than the polarity were also found to influence the reaction rates. From the oxidations of adamantane and adamantane-1,3,5,7-d{sub 4} two primary kinetic deuterium isotope effects were found. These were comparable with the deuterium isotope effects found for the analogous oxidations of cis-decalin and cis-decalin-d{sub 18}. The results seem to exclude both a one step hydride abstraction reaction mechanism and a one step concerted mechanism, as well as a scheme where two such mechanisms compete. The observations may be explained by a two step reaction mechanism consisting of a pre-equilibrium with formation of a substrate-RuO{sub 4} complex followed by a concerted rate determining reaction. The RuO{sub 4}-mediated oxidation of ethers was of kinetic second order with a small enthalpy of activation and a large negative entropy of activation. Oxidation of cyclopropylmethyl methyl ether gave methyl cyclopropanecarboxylate, no rearranged products were observed. On RuO{sub 4} oxidations in CCl{sub 4} with NaIO{sub 4} as stoichiometric oxidant, no chlorinated products were observed. Several observations not in agreement with a hydride or a hydrogen abstraction mechanism may be explained by assuming that the reaction proceeds by either a concerted reaction or by a reversible oxidative addition of the ether to RuO{sub 4} followed by a slow concerted step. 228 refs., 9 figs., 27 tabs.

  3. Ruthenium porphyrin-induced photodamage in bladder cancer cells.

    Bogoeva, Vanya; Siksjø, Monica; Sæterbø, Kristin G; Melø, Thor Bernt; Bjørkøy, Astrid; Lindgren, Mikael; Gederaas, Odrun A

    2016-06-01

    Photodynamic therapy (PDT) is a noninvasive treatment for solid malignant and flat tumors. Light activated sensitizers catalyze photochemical reactions that produce reactive oxygen species which can cause cancer cell death. In this work we investigated the photophysical properties of the photosensitizer ruthenium(II) porphyrin (RuP), along with its PDT efficiency onto rat bladder cancer cells (AY27). Optical spectroscopy verified that RuP is capable to activate singlet oxygen via blue and red absorption bands and inter system crossing (ISC) to the triplet state. In vitro experiments on AY27 indicated increased photo-toxicity of RuP (20μM, 18h incubation) after cell illumination (at 435nm), as a function of blue light exposure. Cell survival fraction was significantly reduced to 14% after illumination of 20μM RuP with 15.6J/cm(2), whereas the "dark toxicity" of 20μM RuP was 17%. Structural and morphological changes of cells were observed, due to RuP accumulation, as well as light-dependent cell death was recorded by confocal microscopy. Flow cytometry verified that PDT-RuP (50μM) triggered significant photo-induced cellular destruction with a photoxicity of (93%±0.9%). Interestingly, the present investigation of RuP-PDT showed that the dominating mode of cell death is necrosis. RuP "dark toxicity" compared to the conventional chemotherapeutic drug cisplatin was higher, both evaluated by the MTT assay (24h). In conclusion, the present investigation shows that RuP with or without photoactivation induces cell death of bladder cancer cells. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. Catalytic water oxidation by ruthenium(II) quaterpyridine (qpy) complexes: evidence for ruthenium(III) qpy-N,N'''-dioxide as the real catalysts.

    Liu, Yingying; Ng, Siu-Mui; Yiu, Shek-Man; Lam, William W Y; Wei, Xi-Guang; Lau, Kai-Chung; Lau, Tai-Chu

    2014-12-22

    Polypyridyl and related ligands have been widely used for the development of water oxidation catalysts. Supposedly these ligands are oxidation-resistant and can stabilize high-oxidation-state intermediates. In this work a series of ruthenium(II) complexes [Ru(qpy)(L)2 ](2+) (qpy=2,2':6',2'':6'',2'''-quaterpyridine; L=substituted pyridine) have been synthesized and found to catalyze Ce(IV) -driven water oxidation, with turnover numbers of up to 2100. However, these ruthenium complexes are found to function only as precatalysts; first, they have to be oxidized to the qpy-N,N'''-dioxide (ONNO) complexes [Ru(ONNO)(L)2 ](3+) which are the real catalysts for water oxidation. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. CLSI-based transference and verification of CALIPER pediatric reference intervals for 29 Ortho VITROS 5600 chemistry assays.

    Higgins, Victoria; Truong, Dorothy; Woroch, Amy; Chan, Man Khun; Tahmasebi, Houman; Adeli, Khosrow

    2018-03-01

    Evidence-based reference intervals (RIs) are essential to accurately interpret pediatric laboratory test results. To fill gaps in pediatric RIs, the Canadian Laboratory Initiative on Pediatric Reference Intervals (CALIPER) project developed an age- and sex-specific pediatric RI database based on healthy pediatric subjects. Originally established for Abbott ARCHITECT assays, CALIPER RIs were transferred to assays on Beckman, Roche, Siemens, and Ortho analytical platforms. This study provides transferred reference intervals for 29 biochemical assays for the Ortho VITROS 5600 Chemistry System (Ortho). Based on Clinical Laboratory Standards Institute (CLSI) guidelines, a method comparison analysis was performed by measuring approximately 200 patient serum samples using Abbott and Ortho assays. The equation of the line of best fit was calculated and the appropriateness of the linear model was assessed. This equation was used to transfer RIs from Abbott to Ortho assays. Transferred RIs were verified using 84 healthy pediatric serum samples from the CALIPER cohort. RIs for most chemistry analytes successfully transferred from Abbott to Ortho assays. Calcium and CO 2 did not meet statistical criteria for transference (r 2 reference intervals, 29 successfully verified with approximately 90% of results from reference samples falling within transferred confidence limits. Transferred RIs for total bilirubin, magnesium, and LDH did not meet verification criteria and are not reported. This study broadens the utility of the CALIPER pediatric RI database to laboratories using Ortho VITROS 5600 biochemical assays. Clinical laboratories should verify CALIPER reference intervals for their specific analytical platform and local population as recommended by CLSI. Copyright © 2018 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

  6. Distinction of tris(diimine)ruthenium(II) enantiomers chiral by virtue of helical chirality: temperature-dependent deuterium NMR spectroscopy in partially oriented phases.

    Szalontai, Gábor; Kovács, Margit

    2006-11-01

    2H NMR spectra of perdeuterated tris(diimine)ruthenium(II) complexes have been recorded in lyotropic liquid crystalline phase formed by the chiral polypeptide, poly-gamma-benzyl-L-glutamate (PBLG) and co-solvents. It is demonstrated that the left- and right-rotation isomers of these octahedral metal complexes with D3 symmetry can be distinguished. The effects of temperature and ligand size on spectral resolution were also studied. Although in the case of free bipyridine ligands excellent optical resolution could be obtained at room temperature in the complexes studied, the increase in ligand size has a detrimental effect on the resolution. This can be compensated to some extent by elevating the sample temperature and decreasing the deuterium relaxation rates, but the available temperature range and therefore the applicability of the technique are limited. Copyright 2006 John Wiley & Sons, Ltd.

  7. Direct Vinylation of Alcohols or Aldehydes Employing Alkynes as Vinyl Donors: A Ruthenium Catalyzed C-C Bond Forming Transfer Hydrogenation

    Patman, Ryan L.; Chaulagain, Mani Raj; Williams, Vanessa M.; Krische, Michael J.

    2011-01-01

    Under the conditions of ruthenium catalyzed transfer hydrogenation, 2-butyne couples to benzylic and aliphatic alcohols 1a–1i to furnish allylic alcohols 2a–2i, constituting a direct C-H vinylation of alcohols employing alkynes as vinyl donors. Under related transfer hydrogenation conditions employing formic acid as terminal reductant, 2-butyne couples to aldehydes 4a, 4b, and 4e to furnish identical products of carbonyl vinylation 2a, 2b, and 2e. Thus, carbonyl vinylation is achieved from the alcohol or the aldehyde oxidation level in the absence of any stoichiometric metallic reagents. Nonsymmetric alkynes 6a–6c couple efficiently to aldehyde 4b to provide allylic alcohols 2m–2o as single regioisomers. Acetylenic aldehyde 7a engages in efficient intramolecular coupling to deliver cyclic allylic alcohol 8a. PMID:19173651

  8. Electrochemiluminescence and chemiluminescence of a carboxylic acid derivative of ruthenium(II) tris-(2,2'-bipyridine) chelate synthesized for labeling purposes

    Jiang Qinghong; Sun Shiguo; Hakansson, Markus; Langel, Kaarina; Ylinen, Tiina; Suomi, Johanna; Kulmala, Sakari

    2006-01-01

    Synthesis, purification and characterization of [4-ethoxycarbonyl-4'-carboxy-2,2'-bipyridine]bis(2,2'-bipyridine) ruthenium(II) hexafluorophosphate is described. This complex is shown to be electrochemiluminescent in aqueous solution during cathodic pulse polarization of thin insulating film-coated electrodes. Electrochemiluminescence (ECL) lifetime of the complex was observed to be ca. 40 μs at oxide-coated n-silicon electrodes; thus time-resolved detection is also possible. The ECL emission maximum of this carboxylate derivative is somewhat red-shifted when compared with an unmodified Ru(bpy) 3 2+ . Because the present complex can be easily covalently coupled with antibodies and oligonucleotides it is usable as an electrochemiluminescent label in various bioaffinity assays. The present chelates also produce strong chemiluminescence during dissolution of metallic magnesium in aqueous solution

  9. Hall effect measurement for precise sheet resistance and thickness evaluation of Ruthenium thin films using non-equidistant four-point probes

    Frederik Westergaard Østerberg

    2018-05-01

    Full Text Available We present a new micro Hall effect measurement method using non-equidistant electrodes. We show theoretically and verify experimentally that it is advantageous to use non-equidistant electrodes for samples with low Hall sheet resistance. We demonstrate the new method by experiments where Hall sheet carrier densities and Hall mobilities of Ruthenium thin films (3-30 nm are determined. The measurements show that it is possible to measure Hall mobilities as low as 1 cm2V−1s−1 with a relative standard deviation of 2-3%. We show a linear relation between measured Hall sheet carrier density and film thickness. Thus, the method can be used to monitor thickness variations of ultra-thin metal films.

  10. Acetic Acid Formation by Selective Aerobic Oxidation of Aqueous Ethanol over Heterogeneous Ruthenium Catalysts

    Gorbanev, Yury; Kegnæs, Søren; Hanning, Christopher William

    2012-01-01

    Heterogeneous catalyst systems comprising ruthenium hydroxide supported on different carrier materials, titania, alumina, ceria, and spinel (MgAl2O4), were applied in selective aerobic oxidation ethanol to form acetic acid, an important bulk chemical and food ingredient. The catalysts were...

  11. Activity of iridium-ruthenium and iridium-rhodium adsorption catalysts in decomposition of hydrogen peroxide

    Zubovich, I A; Mikhaylov, V A; Migulina, N N [Yaroslavskij Politekhnicheskij Inst. (USSR)

    1976-06-01

    Experimental data for the activities of iridium-ruthenium and iridium-rhodium adsorption catalysts in the decomposition of hydrogen peroxide are considered and the results of magnetic susceptibility measurements are presented. It is concluded that surface structures (complexes) may be formed and that micro-electronic feaures play a role in heterogeneous catalysis.

  12. Elimination of ionic interference effects in the atomic absorption spectrometric determination of ruthenium

    El-Defrawy, M.M.M.; Posta, J.; Beck, M.T.

    1978-01-01

    In connection with work on the catalytic effect of ruthenium complexes, new compounds were prepared. Atomic absorption spectrometry (a.a.s.) was to be used for their analysis. The standard methods could not be applied to the complexes studied, therefore the effect of cyanide ions for elimination of interfering effects has been studied, because of the great stability of cyanide complexes. (Auth.)

  13. Hydrogenation of esters catalyzed by ruthenium PN3-Pincer complexes containing an aminophosphine arm

    Chen, Tao

    2014-08-11

    Hydrogenation of esters under mild conditions was achieved using air-stable ruthenium PN3-pincer complexes containing an aminophosphine arm. High efficiency was achieved even in the presence of water. DFT studies suggest a bimolecular proton shuttle mechanism which allows H2 to be activated by the relatively stable catalyst with a reasonably low transition state barrier. © 2014 American Chemical Society.

  14. Design and synthesis of ruthenium(II) OCO pincer type NHC ...

    The tridentate nature of the tBu(OCO)2− ligand as well as some level of steric protection ... our previous results of ruthenium(II) o-hydroxyaryl sub- stituted bidentate NHC ...... (a) Ribelin T, Katz C E, English D G, Smith S,. Manukyan A K, Day ...

  15. Preliminary assessment of modified borosilicate glasses for chromium and ruthenium immobilization

    Farid, Osama M. [Reactors Department, Nuclear Research Center, Atomic Energy Authority of Egypt, P.O. 13759, Inshas, Cairo (Egypt); Centre of Nuclear Engineering (CNE), Department of Materials, Imperial College London, London, SW7 2BP (United Kingdom); Abdel Rahman, R.O., E-mail: alaarehab@yahoo.com [Hot Laboratory Center, Atomic Energy Authority of Egypt, P.O. 13759, Inshas, Cairo (Egypt)

    2017-01-15

    The feasibility of using modified alkali borosilicate glasses for ruthenium and chromium immobilization is preliminary assessed by investigating the immobilization system structure under normal conditions. Within this context, reference alkali borosilicate, and simulated Magnox-modified glasses were prepared and studied. The results indicate that ruthenium is immobilized in the vitreous structure as encapsulated RuO{sub 2} crystallites that act as seeds for heterogeneous nucleation of other crystalline phases. The presence of Zn, as modifier, has contributed to chromium immobilization in zincochromite spinel structure, whereas Ca is accommodated in the vitreous structure. Immobilization performance was evaluated by conducting conservative static leach test and studying the leached glass. Leached glass morphology was altered, where near surface reference glass is leached over 400 nm and simulated Magnox-modified sample is altered over 300 nm. Normalized release rates are within normal range for borosilicate material. For simulated Magnox-modified sample, Ca and alkali structural element, i.e. Na and Li, are leached via ion-exchange reaction. The ion-exchanged fraction equals 1.06 × 10{sup −8} mol/m{sup 2} s and chromium has slightly lower normalized release rate value than ruthenium. - Highlights: • The presence of modifiers and waste oxides led to localized de-vitrification. • Ruthenium is encapsulated within the vitreous glass network as RuO{sub 2} crystals. • Chromium is immobilized within the zincochromite spinel structure. • Pitting and cracks induced by leaching did not affect the immobilization performance.

  16. Dinuclear ruthenium sawhorse-type complexes containing carboxylato bridges and ferrocenyl substituents: Synthesis and electrochemistry

    Auzias, M.; Süss-Fink, G.; Štěpnička, P.; Ludvík, Jiří

    2007-01-01

    Roč. 360, č. 6 (2007), s. 2023-2028 ISSN 0020-1693 Institutional research plan: CEZ:AV0Z40400503 Keywords : carboxylato bridges * dinuclear complexes * ruthenium * electrochemistry Subject RIV: CG - Electrochemistry Impact factor: 1.713, year: 2007

  17. Contribution to the study of the fluorination of ruthenium and its dioxide

    Courtois, Charles.

    1977-12-01

    Compounds formed during fluorination of ruthenium and its dioxide are studied. By chemical analysis the constitution of these compounds is cleared up. RuF 5 is the main compound formed, but a secondary product is obtained which is RuF 8 . The vapor pressure of this product is given between 178 and 221 0 K, and its infrared spectrum is drawn [fr

  18. Highly dispersed supported ruthenium oxide as an aerobic catalyst for acetic acid synthesis

    Laursen, Anders Bo; Gorbanev, Yury; Cavalca, Filippo

    2012-01-01

    The increasing need for shifting to renewable feedstocks in the chemical industry has driven research toward using green aerobic, selective oxidation reactions to produce bulk chemicals. Here, we report the use of a ruthenium mixed oxide/hydroxide (RuOx) on different support materials for the sel...

  19. A technique for studying digestion by grasshoppers using a 103Ruthenium-labelled marker

    Gandar, M.V.

    1981-01-01

    103 Ru-labelled tris (I,10-phenanthroline) ruthenium (II) chloride has proved to be a convenient marker in investigating digestion in grasshoppers. Assimilation efficiencies and the retension time of the food in the gut were measured. It is surmised that the technique described in this paper will be applicable to studies of a variety of chewing herbivorous insects. (author)

  20. Structural, spectral, DFT and biological studies on macrocyclic mononuclear ruthenium (II) complexes

    Muthukkumar, M.; Kamal, C.; Venkatesh, G.; Kaya, C.; Kaya, S.; Enoch, Israel V. M. V.; Vennila, P.; Rajavel, R.

    2017-11-01

    Macrocyclic mononuclear ruthenium (II) complexes have been synthesized by condensation method [Ru (L1, L2, L3) Cl2] L1 = (C36 H31 N9), L2= (C42H36N8), L3= (C32H32 N8)]. These ruthenium complexes have been established by elemental analyses and spectroscopic techniques (Fourier transform infrared spectroscopy (FT-IR), 1H- nuclear magnetic resonance (NMR), 13C- NMR and Electrospray ionization mass spectrometry (ESI-MS)). The coordination mode of the ligand has been confirmed and the octahedral geometry around the ruthenium ion has been revealed. Binding affinity and binding mode of ruthenium (II) complexes with Bovine serum Albumin (BSA) have been characterized by Emission spectra analysis. UV-Visible and fluorescence spectroscopic techniques have also been utilized to examine the interaction between ligand and its complexes L1, L2, & L3 with BSA. Chemical parameters and molecular structure of Ru (II) complexes L1H, L2H, & L3H have been determined by DFT coupled with B3LYP/6-311G** functional in both the gaseous and aqueous phases.

  1. Ion implantation to improve mechanical and electrical properties of resistive materials based on ruthenium dioxide

    Byeli, A.V.; Shykh, S.K.; Beresina, V.P.

    1996-01-01

    This paper reports the influence of ion implantation, using different chemical species, on the surface micromorphology, wear resistance, coefficient of friction and electrical resistivity, and its variation during friction for resistive materials based on ruthenium dioxide. It is demonstrated that nitrogen and hydrogen ions are the most effective for modifying surface properties. (Author)

  2. A study of ruthenium complexes of some biologically relevant a-N ...

    Home; Journals; Journal of Chemical Sciences; Volume 112; Issue 3. A study of ruthenium complexes of some biologically relevant ∙ -N-heterocyclic ... Author Affiliations. P Sengupta1 S Ghosh1. Department of Inorganic Chemistry, Indian Association for the Cultivation of Science, Jadavpur, Calcutta 700 032, India ...

  3. New soluble functional polymers by free-radical copolymerization of methacrylates and bipyridine ruthenium complexes

    Holder, E.; Meier, M.A.R.; Marin, V.N.; Schubert, U.S.

    2003-01-01

    The luminescent complex [4-(3-hydroxypropyl)-4-methyl-2,2-bipyridine]-bis(2,2-bipyridine)-ruthenium(II)-bis(hexafluoroantimonate) and its methacrylate derivative were successfully synthesized and fully characterized by two-dimensional 1H and 13C{1H} NMR techniques [correlation spectroscopy (COSY)

  4. Electronic Interplay between TTF and Extended-TCNQ Electrophores along a Ruthenium Bis(acetylide) Linker.

    Vacher, Antoine; Auffray, Morgan; Barrière, Frédéric; Roisnel, Thierry; Lorcy, Dominique

    2017-11-17

    A bis(TTF-butadiynyl) ruthenium D-D'-D complex, with intramolecular electronic interplay between the three electron-donating electrophores, was easily converted through a cycloaddition-retroelectrocyclization with TCNQ into a D-A-D'-A-D pentad complex, which exhibits an intense intramolecular charge transfer together with an electronic interplay between the two acceptors along the conjugated organometallic bridge.

  5. Graphene/Ruthenium Active Species Aerogel as Electrode for Supercapacitor Applications.

    Gigot, Arnaud; Fontana, Marco; Pirri, Candido Fabrizio; Rivolo, Paola

    2017-12-30

    Ruthenium active species containing Ruthenium Sulphide (RuS₂) is synthesized together with a self-assembled reduced graphene oxide (RGO) aerogel by a one-pot hydrothermal synthesis. Ruthenium Chloride and L-Cysteine are used as reactants. The hydrothermal synthesis of the innovative hybrid material occurs at 180 °C for 12 h, by using water as solvent. The structure and morphology of the hybrid material are fully characterized by Raman, XRD, XPS, FESEM and TEM. The XRD and diffraction pattern obtained by TEM display an amorphous nanostructure of RuS₂ on RGO crystallized flakes. The specific capacitance measured in planar configuration in 1 M NaCl electrolyte at 5 mV s -1 is 238 F g -1 . This supercapacitor electrode also exhibits perfect cyclic stability without loss of the specific capacitance after 15,000 cycles. In summary, the RGO/Ruthenium active species hybrid material demonstrates remarkable properties for use as active material for supercapacitor applications.

  6. Magnetically Recoverable Supported Ruthenium Catalyst for Hydrogenation of Alkynes and Transfer Hydrogenation of Carbonyl Compounds

    A ruthenium (Ru) catalyst supported on magnetic nanoparticles (NiFe2O4) has been successfully synthesized and used for hydrogenation of alkynes at room temperature as well as transfer hydrogenation of a number of carbonyl compounds under microwave irradiation conditions. The cata...

  7. Ruthenium-catalyzed cyclization of N-carbamoyl indolines with alkynes: an efficient route to pyrroloquinolinones.

    Manoharan, Ramasamy; Jeganmohan, Masilamani

    2015-09-21

    A regioselective synthesis of substituted pyrroloquinolinones via a ruthenium-catalyzed oxidative cyclization of substituted N-carbamoyl indolines with alkynes is described. The cyclization reaction was compatible with various symmetrical and unsymmetrical alkynes including substituted propiolates. Later, we performed the aromatization of pyrroloquinolinones into indole derivatives in the presence of 2,3-dichloro-5,6-dicyanobenzoquinone (DDQ).

  8. Studies On An Aerobic Oxidation Of Dibenzothiophene And Related Compounds Using Ruthenium Catalyst

    Morishita Y.

    2015-06-01

    Full Text Available An aerobic oxidation of dibenzothiophene and related compounds using a catalytic amount of ruthenium chloride in hydrocarbon solvents at 80°C for 20 h gave the corresponding sulfones in almost quantitative yields. The reaction might proceed via autoxidation of solvents to hydroperoxides and the reaction of sulfur compounds with the resulting hydroperoxides.

  9. Photo-induced DNA cleavage and cytotoxicity of a ruthenium(II) arene anticancer complex

    Brabec, Viktor; Prachařová, J.; Štěpánková, Jana; Sadler, P. J.; Kašpárková, Jana

    2016-01-01

    Roč. 160, JUL2016 (2016), s. 149-155 ISSN 0162-0134 R&D Projects: GA ČR(CZ) GA14-21053S; GA MŠk(CZ) LD14019 Institutional support: RVO:68081707 Keywords : Ruthenium anticancer complex * DNA cleavage * Phototoxicity Subject RIV: BO - Biophysics Impact factor: 3.348, year: 2016

  10. Mixed-ligand complexes of ruthenium(II) incorporating a diazo ...

    Unknown

    Dedicated to the memory of the late Professor Bhaskar G Maiya. *For correspondence. Mixed-ligand complexes of ruthenium(II) incorporating a diazo ligand: Synthesis .... water (1 : 1) for 5 h to give a dark red solution. The solution was cooled to room temperature. After eva- poration of the solvent, the solid was collected,.

  11. Correlations between electrochemical and spectrochemical parameters of ruthenium sulfoxides series with N-heterocyclic

    Oliveira, D. de; Toma, H.E.

    1990-01-01

    A systematic study of Ru Cl sub(2) (DMSO) sub(2) L sub(2) derivates, where L = N-heterocyclic base is described, contributing for a best understanding of chemical behaviour and electronic structure of the ruthenium sulfoxides. The correlations between the electrochemical and the spectroscopical parameters of the serie are presented with more emphasis. (author)

  12. Investigation of Ruthenium Dissolution in Advanced Membrane Electrode Assemblies for Direct Methanol Based Fuel Cell Stacks

    Valdez, Thomas I.; Firdosy, S.; Koel, B. E.; Narayanan, S. R.

    2005-01-01

    Dissolution of ruthenium was observed in the 80-cell stack. Duration testing was performed in single cell MEAs to determine the pathway of cell degradation. EDAX analysis on each of the single cell MEAs has shown that the Johnson Matthey commercial catalyst is stable in DMFC operation for 250 hours, no ruthenium dissolution was observed. Changes in the hydrophobicity of the cathode backing papers was minimum. Electrode polarization analysis revealed that the MEA performance loss is attributed to changes in the cathode catalyst layer. Ruthenium migration does not seem to occur during cell operation but can occur when methanol is absent from the anode compartment, the cathode compartment has access to air, and the cells in the stack are electrically connected to a load (Shunt Currents). The open-to-air cathode stack design allowed for: a) The MEAs to have continual access to oxygen; and b) The stack to sustain shunt currents. Ruthenium dissolution in a DMFC stack can be prevented by: a) Developing an internally manifolded stacks that seal reactant compartments when not in operation; b) Bringing the cell voltages to zero quickly when not in operation; and c) Limiting the total number of cells to 25 in an effort to limit shunt currents.

  13. Investigation of Ruthenium Dissolution in Advanced Membrane Electrode Assemblies for Direct Methanol Based Fuel Cells Stacks

    Valdez, T. I.; Firdosy, S.; Koel, B. E.; Narayanan, S. R.

    2005-01-01

    This viewgraph presentation gives a detailed review of the Direct Methanol Based Fuel Cell (DMFC) stack and investigates the Ruthenium that was found at the exit of the stack. The topics include: 1) Motivation; 2) Pathways for Cell Degradation; 3) Cell Duration Testing; 4) Duration Testing, MEA Analysis; and 5) Stack Degradation Analysis.

  14. Aerobic Oxidation of 5-(Hydroxymethyl)furfural in Ionic Liquids with Solid Ruthenium Hydroxide Catalysts

    Ståhlberg, Tim Johannes Bjarki; Eyjolfsdottir, Ester; Gorbanev, Yury

    2012-01-01

    The aerobic oxidation of 5-(hydroxymethyl)furfural was investigated over solid ruthenium hydroxide catalysts in ionic liquids at elevated temperatures and pressures. Several different catalyst supports were tested in combination with various ionic liquids. The best result was obtained in [EMIm...

  15. Tailoring the Selectivity for Electrocatalytic Oxygen Evolution on Ruthenium Oxides by Zinc Substitution

    Petrykin, Valery; Macounová, Kateřina; Shlyakhtin, O. A.; Krtil, Petr

    2010-01-01

    Roč. 49, č. 28 (2010), s. 4813-4815 ISSN 1433-7851 R&D Projects: GA AV ČR IAA400400906 Institutional research plan: CEZ:AV0Z40400503 Keywords : electrocatalysis * ruthenium oxides * zinc substitution Subject RIV: CG - Electrochemistry Impact factor: 12.730, year: 2010

  16. Efficient oxygen reduction reaction using ruthenium tetrakis(diaquaplatinum)octacarboxyphthalocyanine catalyst supported on MWCNT platform

    Maxakato, NW

    2011-02-01

    Full Text Available -1 Electroanalysis 2011, 23, No. 2, 325 ? 329 Efficient Oxygen Reduction Reaction Using Ruthenium Tetrakis(diaquaplatinum)Octacarboxyphthalocyanine Catalyst Supported on MWCNT Platform Nobanathi W. Maxakato,a Solomon A. Mamuru,a Kenneth I. Ozoemena*a, b a...

  17. Room temperature aerobic oxidation of amines by a nanocrystalline ruthenium oxide pyrochlore nafion composite catalyst.

    Venkatesan, Shanmuganathan; Kumar, Annamalai Senthil; Lee, Jyh-Fu; Chan, Ting-Shan; Zen, Jyh-Myng

    2012-05-14

    The aerobic oxidation of primary amines to their respective nitriles has been carried out at room temperature using a highly reusable nanocrystalline ruthenium oxide pyrochlore Nafion composite catalyst (see figure). Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Study of the emission oxidative reactions of ruthenium (II) complex by cationic compounds in anionic micelles

    Bonilha, J.B.S.

    1985-01-01

    The oxidative quenching of the emission of the tetraanionic complex tris (4,4' dicarboxylate - 2,2' - bipyridine ruthenium (II) in aqueous solution, by both organic and inorganic compounds in presence of anionic detergents, above and below the critical micelle concentration is studied. The organic cations, the inorganic ion and detergents used are shown. (M.J.C.) [pt

  19. Platinum group metal nitrides and carbides: synthesis, properties and simulation

    Ivanovskii, Alexander L

    2009-01-01

    Experimental and theoretical data on new compounds, nitrides and carbides of the platinum group 4d and 5d metals (ruthenium, rhodium, palladium, osmium, iridium, platinum), published over the past five years are summarized. The extreme mechanical properties of platinoid nitrides and carbides, i.e., their high strength and low compressibility, are noted. The prospects of further studies and the scope of application of these compounds are discussed.

  20. Photo-degradation of CT-DNA with a series of carbothioamide ruthenium (II) complexes - Synthesis and structural analysis

    Muthuraj, V.; Umadevi, M.

    2018-04-01

    The present research article is related with the method of preparation, structure and spectroscopic properties of a series of carbothioamide ruthenium (II) complexes with N and S donor ligands namely, 2-((6-chloro-4-oxo-4H-chromen-3-yl)methylene) hydrazine carbothioamide (ClChrTs)/2-((6-methoxy-4-oxo-4H-chromen-3-yl)methylene)hydrazine carbothioamide (MeOChrTS). The synthesized complexes were characterized by several techniques using analytical methods as well as by spectral techniques such as FT-IR, 1HNMR, 13CNMR, ESI mass and thermogravimetry/differential thermal analysis (TG-DTA). The IR spectra shows that the ligand acts as a neutral bidentate with N and S donor atoms. The biological activity of the prepared compounds and metal complexes were tested against cell line of calf-thymus DNA via an intercalation mechanism (MCF-7). In addition, the interaction of Ru(II) complexes and its free ligands with CT-DNA were also investigated by titration with UV-Vis spectra, fluorescence spectra, and Circular dichroism studies. Results suggest that both of the two Ru(II) complexes can bind with calf-thymus DNA via an intercalation mechanism.