The optimum spanning catenary cable

Science.gov (United States)

Wang, C. Y.

2015-03-01

A heavy cable spans two points in space. There exists an optimum cable length such that the maximum tension is minimized. If the two end points are at the same level, the optimum length is 1.258 times the distance between the ends. The optimum lengths for end points of different heights are also found.

Nondissipative optimum charge regulator

Science.gov (United States)

Rosen, R.; Vitebsky, J. N.

1970-01-01

Optimum charge regulator provides constant level charge/discharge control of storage batteries. Basic power transfer and control is performed by solar panel coupled to battery through power switching circuit. Optimum controller senses battery current and modifies duty cycle of switching circuit to maximize current available to battery.

Optimum energy levels and offsets for organic donor/acceptor binary photovoltaic materials and solar cells

International Nuclear Information System (INIS)

Sun, S.-S.

2005-01-01

Optimum frontier orbital energy levels and offsets of an organic donor/acceptor binary type photovoltaic material have been analyzed using classic Marcus electron transfer theory in order to achieve the most efficient photo induced charge separation. This study reveals that, an exciton quenching parameter (EQP) yields one optimum donor/acceptor frontier orbital energy offset that equals the sum of the exciton binding energy and the charge separation reorganization energy, where the photo generated excitons are converted into charges most efficiently. A recombination quenching parameter (RQP) yields a second optimum donor/acceptor energy offset where the ratio of charge separation rate constant over charge recombination rate constant becomes largest. It is desirable that the maximum RQP is coincidence or close to the maximum EQP. A third energy offset is also identified where charge recombination becomes most severe. It is desirable that the most severe charge recombination offset is far away from maximum EQP offset. These findings are very critical for evaluating and fine tuning frontier orbital energy levels of a donor/acceptor pair in order to realize high efficiency organic photovoltaic materials

Optimum extracted H- and D- current densities from gas-pressure-limited high-power hydrogen/deuterium tandem ion sources

International Nuclear Information System (INIS)

Hiskes, J.R.

1993-01-01

The tandem hydrogen/deuterium ion source is modelled for the purpose of identifying the maximum current densities that can be extracted subject to the gas-pressure constraints proposed for contemporary beam-line systems. Optimum useful extracted current densities are found to be in the range of approximately 7 to 10 mA cm -2 . The sensitivity of these current densities is examined subject to uncertainties in the underlying atomic/molecular rate processes; A principal uncertainty remains the quantification of the molecular vibrational distribution following H 3 + wall collisions

Optimum Combination and Effect Analysis of Piezoresistor Dimensions in Micro Piezoresistive Pressure Sensor Using Design of Experiments and ANOVA: a Taguchi Approach

Directory of Open Access Journals (Sweden)

Kirankumar B. Balavalad

2017-04-01

Full Text Available Piezoresistive (PZR pressure sensors have gained importance because of their robust construction, high sensitivity and good linearity. The conventional PZR pressure sensor consists of 4 piezoresistors placed on diaphragm and are connected in the form of Wheatstone bridge. These sensors convert stress applied on them into change in resistance, which is quantified into voltage using Wheatstone bridge mechanism. It is observed form the literature that, the dimensions of piezoresistors are very crucial in the performance of the piezoresistive pressure sensor. This paper presents, a novel mechanism of finding best combinations and effect of individual piezoresistors dimensions viz., Length, Width and Thickness, using DoE and ANOVA (Analysis of Variance method, following Taguchi experimentation approach. The paper presents a unique method to find optimum combination of piezoresistors dimensions and also clearly illustrates the effect the dimensions on the output of the sensor. The optimum combinations and the output response of sensor is predicted using DoE and the validation simulation is done. The result of the validation simulation is compared with the predicted value of sensor response i.e., V. Predicted value of V is 1.074 V and the validation simulation gave the response for V as 1.19 V. This actually validates that the model (DoE and ANOVA is adequate in describing V in terms of the variables defined.

Generic Advertising Optimum Budget for Iran’s Milk Industry

Directory of Open Access Journals (Sweden)

H. Shahbazi

2016-05-01

Full Text Available Introduction One of the main targets of planners, decision makers and governments is increasing society health with promotion and production of suitable and healthy food. One of the basic commodities that have important role in satisfaction of required human food is milk. So, some part of government and producer healthy budget allocate to milk consumption promotion by using generic advertising. If effectiveness of advertising budget on profitability is more, producer will have more willing to spend for advertising. Determination of optimal generic advertising budget is one of important problem in managerial decision making in producing firm as well as increase in consumption and profit and decrease in wasting and non-optimality of budget. Materials and Methods: In this study, optimal generic advertising budget intensity index (advertising budget share of production cost was estimated under two different scenarios by using equilibrium replacement model. In equilibrium replacement model, producer surplus are maximized in respect to generic advertising in retail level. According to market where two levels of farm and processing before retail exist and there is trade in farm and retail level, we present different models. Fixed and variable proportion hypothesis is another one. Finally, eight relations are presented for determination of milk generic advertising optimum budget. So, we use data from several resources such as previous studies, national (Iran Static center and international institute (Fao formal data and own estimation. Because there are several estimations in previous studies, we identify some scenarios (in two general scenarios for calculation of milk generic advertising optimum budget. Results and Discussion: Estimation of milk generic advertising optimum budget in scenario 1 shows that in case of one market level, fixed supplies and no trade, optimum budget is 0.4672539 percent. In case of one market level and no trade, optimum

Optimum fiber distribution in singlewall corrugated fiberboard

Science.gov (United States)

Millard W. Johnson; Thomas J. Urbanik; William E. Denniston

1979-01-01

Determining optimum distribution of fiber through rational design of corrugated fiberboard could result in significant reductions in fiber required to meet end-use conditions, with subsequent reductions in price pressure and extension of the softwood timber supply. A theory of thin plates under large deformations is developed that is both kinematically and physically...

Evaluation of Optimum Moisture Content for Composting of Beef Manure and Bedding Material Mixtures Using Oxygen Uptake Measurement

Directory of Open Access Journals (Sweden)

Eunjong Kim

2016-05-01

Full Text Available Moisture content influences physiological characteristics of microbes and physical structure of solid matrices during composting of animal manure. If moisture content is maintained at a proper level, aerobic microorganisms show more active oxygen consumption during composting due to increased microbial activity. In this study, optimum moisture levels for composting of two bedding materials (sawdust, rice hull and two different mixtures of bedding and beef manure (BS, Beef cattle manure+sawdust; BR, Beef cattle manure+rice hull were determined based on oxygen uptake rate measured by a pressure sensor method. A broad range of oxygen uptake rates (0.3 to 33.3 mg O2/g VS d were monitored as a function of moisture level and composting feedstock type. The maximum oxygen consumption of each material was observed near the saturated condition, which ranged from 75% to 98% of water holding capacity. The optimum moisture content of BS and BR were 70% and 57% on a wet basis, respectively. Although BS’s optimum moisture content was near saturated state, its free air space kept a favorable level (above 30% for aerobic composting due to the sawdust’s coarse particle size and bulking effect.

Evaluation of Optimum Moisture Content for Composting of Beef Manure and Bedding Material Mixtures Using Oxygen Uptake Measurement.

Science.gov (United States)

Kim, Eunjong; Lee, Dong-Hyun; Won, Seunggun; Ahn, Heekwon

2016-05-01

Moisture content influences physiological characteristics of microbes and physical structure of solid matrices during composting of animal manure. If moisture content is maintained at a proper level, aerobic microorganisms show more active oxygen consumption during composting due to increased microbial activity. In this study, optimum moisture levels for composting of two bedding materials (sawdust, rice hull) and two different mixtures of bedding and beef manure (BS, Beef cattle manure+sawdust; BR, Beef cattle manure+rice hull) were determined based on oxygen uptake rate measured by a pressure sensor method. A broad range of oxygen uptake rates (0.3 to 33.3 mg O2/g VS d) were monitored as a function of moisture level and composting feedstock type. The maximum oxygen consumption of each material was observed near the saturated condition, which ranged from 75% to 98% of water holding capacity. The optimum moisture content of BS and BR were 70% and 57% on a wet basis, respectively. Although BS's optimum moisture content was near saturated state, its free air space kept a favorable level (above 30%) for aerobic composting due to the sawdust's coarse particle size and bulking effect.

Development of Non-Optimum Factors for Launch Vehicle Propellant Tank Bulkhead Weight Estimation

Science.gov (United States)

Wu, K. Chauncey; Wallace, Matthew L.; Cerro, Jeffrey A.

2012-01-01

Non-optimum factors are used during aerospace conceptual and preliminary design to account for the increased weights of as-built structures due to future manufacturing and design details. Use of higher-fidelity non-optimum factors in these early stages of vehicle design can result in more accurate predictions of a concept s actual weights and performance. To help achieve this objective, non-optimum factors are calculated for the aluminum-alloy gores that compose the ogive and ellipsoidal bulkheads of the Space Shuttle Super-Lightweight Tank propellant tanks. Minimum values for actual gore skin thicknesses and weld land dimensions are extracted from selected production drawings, and are used to predict reference gore weights. These actual skin thicknesses are also compared to skin thicknesses predicted using classical structural mechanics and tank proof-test pressures. Both coarse and refined weights models are developed for the gores. The coarse model is based on the proof pressure-sized skin thicknesses, and the refined model uses the actual gore skin thicknesses and design detail dimensions. To determine the gore non-optimum factors, these reference weights are then compared to flight hardware weights reported in a mass properties database. When manufacturing tolerance weight estimates are taken into account, the gore non-optimum factors computed using the coarse weights model range from 1.28 to 2.76, with an average non-optimum factor of 1.90. Application of the refined weights model yields non-optimum factors between 1.00 and 1.50, with an average non-optimum factor of 1.14. To demonstrate their use, these calculated non-optimum factors are used to predict heavier, more realistic gore weights for a proposed heavy-lift launch vehicle s propellant tank bulkheads. These results indicate that relatively simple models can be developed to better estimate the actual weights of large structures for future launch vehicles.

Flashing evaporation under different pressure levels

International Nuclear Information System (INIS)

Liao, Yixiang; Lucas, Dirk; Krepper, Eckhard; Rzehak, Roland

2013-01-01

Highlights: • CFD simulation based on two-fluid model for flashing boiling inside a vertical pipe. • Effect of pressure level on the maximum thermal energy available for evaporation. • Effect of presumed bubble size on the onset of flashing as well as evaporation rate. • Effect of pressure level on the critical bubble size that can start stable flashing. • Effect of pressure level on nucleation rate and mechanism. - Abstract: Flashing evaporation of water inside a vertical pipe under four pressure levels is investigated both experimentally and numerically. In the experiment depressurization is realized through a blow-off valve, and the evaporation rate is controlled by the opening rate and degree of the valve. In the CFD simulation phase change is assumed to be caused by thermal heat transfer between steam–water interface and the surrounding water. Consequently, the evaporation rate is determined by heat transfer coefficient, interfacial area density as well as liquid superheat degree. The simulated temporal course of cross-section averaged steam volume fraction is compared with the measured one. It is found that the increasing rate and maximum value of steam volume fraction is over-predicted under low-pressure conditions, which is mainly caused by the neglect of bubble growth in the mono-dispersed simulation. The agreement is notably improved by performing poly-dispersed simulations with the inhomogeneous MUSIG approach (IMUSIG). On the other hand an underestimation of the maximum steam volume fraction is observed in high-pressure cases, since the contribution of nucleation to the total steam generation rate becomes large as the system pressure increases. Reliable models for nucleation rate as well as bubble detachment size are indispensable for reliable predictions. An effect of the system pressure level on the nucleation mechanism is observed in the experiment

Comparison of optimum tilt angles of solar collectors determined at yearly, seasonal and monthly levels

International Nuclear Information System (INIS)

Despotovic, Milan; Nedic, Vladimir

2015-01-01

Highlights: • Optimum yearly, biannual, seasonal, monthly, and daily tilt angles were found. • Energy collected per square meter is compared for ten different scenarios. • Four seasonal scenarios and two biannual scenarios were considered. • It is sufficient to adjust tilt angles only twice per year. - Abstract: The amount of energy that is transformed in solar collector depends on its tilt angle with respect to horizontal plane and orientation of the collector. In this article the optimum tilt angle of solar collectors for Belgrade, which is located at the latitude of 44°47′N is determined. The optimum tilt angle was found by searching for the values for which the solar radiation on the collector surface is maximum for a particular day or a specific period. In that manner the yearly, biannual, seasonal, monthly, fortnightly, and daily optimum tilt angles are determined. Annually collected energy per square meter of tilted surface is compared for ten different scenarios. In addition, these optimum tilt angles are used to calculate the amount of energy on the surface of PV panels that could be installed at the roof of the building. The results show that for observed case study placing the panels at yearly, seasonal and monthly optimum tilt angles, would yield increasing yearly amount of collected energy by factor of 5.98%, 13.55%, and 15.42% respectively compared to energy that could be collected by putting the panels at current roofs’ surface angles

Determination of optimal conditions for pressure oxidative leaching of Sarcheshmeh Molybdenite concentrate using Taguchi method

Directory of Open Access Journals (Sweden)

Khoshnevisana A.

2012-01-01

Full Text Available The present research work is based on finding the optimum conditions for pressure oxidative leaching of the molybdenite concentrate to produce technical-grade molybdic oxide (MoO3 with high recovery through further treatment of the filtrate solution. The Taguchi method was used to design and minimize the number of experiments. By using Taguchi orthogonal (L25 array, five parameters (time, temperature, oxygen pressure, pulp density and acid concentration at five levels were selected for 25 experiments. The experiments were designed and carried out in a high-pressure reactor in the presence of nitric acid as solvent and oxidizing agent for the molybdenite concentrate and its ReS2 content. The optimum conditions for pressure leaching of molybdenite were obtained through using Signal to Noise analysis and modified by using Minitab software prediction tool. Furthermore, the optimum condition for an economical pressure leaching of rhenium sulfide (ReS2 was achieved with the same process. Analysis of variance (ANOVA showed that the pulp density is of paramount importance in this process.

Procedure for determining the optimum rate of increasing shaft depth

Energy Technology Data Exchange (ETDEWEB)

Durov, E.M.

1983-03-01

Presented is an economic analysis of increasing shaft depth during mine modernization. Investigations carried out by the Yuzhgiproshakht Institute are analyzed. The investigations are aimed at determining the optimum shaft sinking rate (the rate which reduces investment to the minimum). The following factors are considered: coal output of a mine (0.9, 1.2, 1.5 and 1.8 Mt/year), depth at which the new mining level is situated (600, 800, 1200, 1400 and 1600 m), four schemes of increasing depth of 2 central shafts (rock hoisting to ground surface, rock hoisting to the existing level, rock haulage to the developed level, rock haulage to the level being developed using a large diameter borehole drilled from the new level to the shaft bottom and enlarged from shaft bottom to the new level), shaft sinking rate (10, 20, 30, 40, 50 and 60 m/month), range of increasing shaft depth (the difference between depth of the shaft before and after increasing its depth by 100, 200, 300 and 400 m). Comparative evaluations show that the optimum shaft sinking rate depends on the scheme for rock hoisting (one of 4 analyzed), range of increasing shaft depth and gas content in coal seams. The optimum shaft sinking rate ranges from 20 to 40 m/month in coal mines with low methane content and from 20 to 30 m/month in gassy coal mines. The planned coal output of a mine does not influence the optimum shaft sinking rate.

Optimum welding condition of 2017 aluminum similar alloy friction welded joints

Energy Technology Data Exchange (ETDEWEB)

Tsujino R.; Ochi, H. [Osaka Inst. of Tech., Osaka (Japan); Morikawa, K. [Osaka Sangyo Univ., Osaka (Japan); Yamaguchi, H.; Ogawa, K. [Osaka Prefecture Univ., Osaka (Japan); Fujishiro, Y.; Yoshida, M. [Sumitomo Metal Technology Ltd., Hyogo (Japan)

2002-07-01

Usefulness of the statistical analysis for judging optimization of the friction welding conditions was investigated by using 2017 aluminum similar alloy, where many samples under fixed welding conditions were friction welded and analyzed statistically. In general, selection of the optimum friction welding conditions for similar materials is easy. However, it was not always the case for 2017 aluminum alloy. For optimum friction welding conditions of this material, it is necessary to apply relatively larger upset pressure to obtain high friction heating. Joint efficiencies obtained under the optimum friction welding conditions showed large shape parameter (m value) of Weibull distribution as well as in the dissimilar materials previously reported. The m value calculated on the small number of data can be substituted for m value on the 30 data. Therefore, m value is useful for practical use in the factory for assuming the propriety of the friction welding conditions. (orig.)

Planning of optimum production from a natural gas field

Energy Technology Data Exchange (ETDEWEB)

Van Dam, J

1968-03-01

The design of an optimum development plan for a natural gas field always depends on the typical characteristics of the producing field, as well as those of the market to be served by this field. Therefore, a good knowledge of the field parameters, such as the total natural gas reserves, the well productivity, and the dependence of production rates on pipeline pressure and depletion of natural gas reserves, is required prior to designing the development scheme of the field, which in fact depends on the gas-sales contract to be concluded in order to commit the natural gas reserves to the market. In this paper these various technical parameters are discussed in some detail, and on this basis a theoretical/economical analysis of natural gas production is given. For this purpose a simplified economical/mathematical model for the field is proposed, from which optimum production rates at various future dates can be calculated. The results of these calculations are represented in a dimensionless diagram which may serve as an aid in designing optimum development plans for a natural gas field. The use of these graphs is illustrated in a few examples.

Determining optimum aging time using novel core flooding equipment

DEFF Research Database (Denmark)

Ahkami, Mehrdad; Chakravarty, Krishna Hara; Xiarchos, Ioannis

2016-01-01

the optimum aging time regardless of variations in crude oil, rock, and brine properties. State of the art core flooding equipment has been developed that can be used for consistently determining the resistivity of the coreplug during aging and waterflooding using advanced data acquisition software......New methods for enhanced oil recovery are typically developed using core flooding techniques. Establishing reservoir conditions is essential before the experimental campaign commences. The realistic oil-rock wettability can be obtained through optimum aging of the core. Aging time is affected....... In the proposed equipment, independent axial and sleeve pressure can be applied to mimic stresses at reservoir conditions. 10 coreplugs (four sandstones and six chalk samples) from the North Sea have been aged for more than 408 days in total and more than 29000 resistivity data points have been measured...

Development of a pressurizer level compensator for use on N Reactor

International Nuclear Information System (INIS)

Bussell, J.H.

1985-07-01

The instrument described in this report has been developed to compensate the measured water level in the N Reactor pressurizer for temperature effects. N Reactor is a pressurized water nuclear reactor (PWR). The instrument is defined as a pressurizer level compensator (PLC). A pressurizer is used in a PWR to control the primary coolant pressure and provide a surge volume for primary coolant expansion and contraction. A means of compensating for water and steam density is required because of the wide range of pressure and temperature that result from different steady state and transient reactor power levels. The uncompensated level is determined by measurement of differential pressure between the top of the level measurement zone and the bottom of the level measurement zone. Temperature of the water in the pressurizer is the parameter that is used to determine the proper level compensation since water and steam density are primarily functions of temperature in this case. The PLC uses a microprocessor to calculate the compensated level from temperature and differential pressure measurements. This report includes a description of the design, development, and implementation of software and hardware that are in the PLC. 9 refs., 51 figs., 17 tabs

Ultrasonic level sensors for liquids under high pressure

Science.gov (United States)

Zuckerwar, A. J.; Mazel, D. S.; Hodges, D. Y.

1986-01-01

An ultrasonic level sensor of novel design continuously measures the level of a liquid subjected to a high pressure (up to about 40 MPa), as is sometimes required for the effective transfer of the liquid. The sensor operates as a composite resonator fabricated from a standard high-pressure plug. A flat-bottom hole is machined into the plug along its center line. An ultrasonic transducer is bonded rigidly to the interior surface of the bottom wall, while the exterior surface is in contact with the liquid. Although the bottom wall is designed to satisfy the pressure code, it is still sufficiently thin to permit ready excitation of the axisymmetric plate modes of vibration. The liquid level is measured by a conventional pulse-echo technique. A prototype sensor was tested successfully in a 2300-l water vessel at pressures up to about 37 MPa. A spectral analysis of the transmitted pulse reveals that the flexural, extensional, thickness-shear, and radial plate modes are excited into vibration, but none of these appears to be significantly affected by the pressurization of the liquid.

Determination of an optimum reactor coolant system average temperature within the licensed operating window

International Nuclear Information System (INIS)

Thaulez, F.; Basic, I.; Vrbanic, I.

2003-01-01

The Krsko modernization power uprate analyses have been performed in such a way as to cover plant operation in a range of average reactor coolant temperatures (Tavg) of 301.7 deg C to 307.4 deg C, with steam generator tube plugging levels of up to 5%. The upper bound is temporarily restricted to 305.7 deg C, as long as Zirc-4 fuel is present in the core. (It is, however,acceptable to operate at 307.4 deg C with a few Zirc-4 assemblies, if meeting certain conditionsand subjected to a corrosion and rod internal pressure evaluation in the frame of the cyclespecificnuclear core design.) The Tavg optimization method takes into account two effects, that are opposed to each other: the impact of steam pressure on the electrical power output versus the impact of Tavg on the cost of reactor fuel. The positive economical impact of a Tavg increase through the increase in MWe output is around 6 to 8 times higher than the corresponding negative impact on the fuel cost. From this perspective, it is desirable to have Tavg as high as possible. This statement is not affected by a change in the relationship between steam pressure and Tavg level. However, there are also other considerations intervening in the definition of the optimum. This paper discusses the procedure for selection of optimal Tavg for the forthcoming cycle in relation to the impacts of change in Tavg level and/or variations of the steam pressure versus Tavg relationship. (author)

Optimum injection dose rate of hydrogen sulfide scavenger for treatment of petroleum crude oil

Directory of Open Access Journals (Sweden)

T.M. Elshiekh

2016-03-01

Full Text Available Hydrogen sulfide H2S scavengers are chemicals that favorably react with hydrogen sulfide gas to eliminate it and produce environmental friendly products. These products depend on the type and composition of the scavenger and the conditions at which the reaction takes place. The scavenger should be widely available and economical for industry acceptance by having a low unit cost. The optimum values of H2S scavenger injection dose rate of scavenging hydrogen sulfide from the multiphase fluid produced at different wells conditions in one of the Petroleum Companies in Egypt were studied. The optimum values of H2S scavenger injection dose rate depend on pipe diameter, pipe length, gas molar mass velocity, inlet H2S concentration and pressure. The optimization results are obtained for different values of these parameters using the software program Lingo. In general, the optimum values of H2S scavenger injection dose rate of the scavenging of hydrogen sulfide are increased by increasing of the pipe diameter and increasing the inlet H2S concentration, and decreased by increasing the pipe length, gas molar mass velocity and pressure.

Developed Hybrid Model for Propylene Polymerisation at Optimum Reaction Conditions

Directory of Open Access Journals (Sweden)

Mohammad Jakir Hossain Khan

2016-02-01

Full Text Available A statistical model combined with CFD (computational fluid dynamic method was used to explain the detailed phenomena of the process parameters, and a series of experiments were carried out for propylene polymerisation by varying the feed gas composition, reaction initiation temperature, and system pressure, in a fluidised bed catalytic reactor. The propylene polymerisation rate per pass was considered the response to the analysis. Response surface methodology (RSM, with a full factorial central composite experimental design, was applied to develop the model. In this study, analysis of variance (ANOVA indicated an acceptable value for the coefficient of determination and a suitable estimation of a second-order regression model. For better justification, results were also described through a three-dimensional (3D response surface and a related two-dimensional (2D contour plot. These 3D and 2D response analyses provided significant and easy to understand findings on the effect of all the considered process variables on expected findings. To diagnose the model adequacy, the mathematical relationship between the process variables and the extent of polymer conversion was established through the combination of CFD with statistical tools. All the tests showed that the model is an excellent fit with the experimental validation. The maximum extent of polymer conversion per pass was 5.98% at the set time period and with consistent catalyst and co-catalyst feed rates. The optimum conditions for maximum polymerisation was found at reaction temperature (RT 75 °C, system pressure (SP 25 bar, and 75% monomer concentration (MC. The hydrogen percentage was kept fixed at all times. The coefficient of correlation for reaction temperature, system pressure, and monomer concentration ratio, was found to be 0.932. Thus, the experimental results and model predicted values were a reliable fit at optimum process conditions. Detailed and adaptable CFD results were capable

[Possibilities of bi-level positive pressure ventilation in chronic hypoventilation].

Science.gov (United States)

Saaresranta, Tarja; Anttalainen, Ulla; Polo, Olli

2011-01-01

During the last decade, noninvasive bi-level positive pressure ventilation has enabled respiratory support in inpatient wards and at home. In many cases, a bi-level airway pressure ventilator can be used to avoid artificial airway and respirator therapy, and may shorten hospital stay and save costs. The treatment alleviates the patient's dyspnea and fatigue, whereby the quality of life improves, and in certain situations also the life span increases. The implementation of bi-level positive pressure ventilation by the physician requires knowledge of the basics of respiratory physiology and familiarization with the bi-level airway pressure ventilator.

A Study on Determination of Proper Pressurizer Level for Kori Unit 1

Energy Technology Data Exchange (ETDEWEB)

Lee, Chang Sup; Song, Dong Soo [Korea Electric Power Research Institute, Taejon (Korea, Republic of)

1996-12-31

1. Determination of Proper Pressurizer Level. To determine operation level of pressurizer, LOFTRAN code is used with conservative model and assumption. 2. Performance Analysis. To simulate the plant, RETRAN computer code is used with realistic model and assumptions. The control and protection systems are fully credited. The turbine trip event is simulated at the condition of 47.62% of pressurizer level at full power. After that the same event as that with 55% of pressurizer level is simulated. And the FSAR requirements of pressurizer are verified with the new level setpoints. 3. Safety Analysis. As safety analyses, Loss of Normal Feedwater/Station Blackout which is significantly affected by the initial pressurizer water level is performed. Turbine Trip accident is also analyzed to verify if the peak primary side pressure is within the limit. LOFTRAN code is used with conservative mode and assumption. 3. Steam Generator Replacement. Relating to the steam generator replacement planed in 1998, safety analysis in terms of pressurizer level setpoint change. 4. Limit Condition for Operation. The LCO of pressurizer level is changed from 60% to 67.4% which is included pressurizer level uncertainty. (author). 13 refs., figs., tabs.

Preliminary study of optimum ductburning turbofan engine cycle design parameters for supersonic cruising

Science.gov (United States)

Fishbach, L. H.

1978-01-01

The effect of turbofan engine overall pressure ratio, fan pressure ratio, and ductburner temperature rise on the engine weight and cruise fuel consumption for a mach 2.4 supersonic transport was investigated. Design point engines, optimized purely for the supersonic cruising portion of the flight where the bulk of the fuel is consumed, are considered. Based on constant thrust requirements at cruise, fuel consumption considerations would favor medium by pass ratio engines (1.5 to 1.8) of overall pressure ratio of about 16. Engine weight considerations favor low bypass ratio (0.6 or less) and low wverall pressure ratio (8). Combination of both effects results in bypass ratios of 0.6 to 0.8 and overall pressure ratio of 12 being the overall optimum.

Optimum Conditions for Uricase Enzyme Production by Gliomastix gueg

Directory of Open Access Journals (Sweden)

Atalla, M. M.

2009-01-01

Full Text Available Nineteen strains of microorganisms were screened for uricase production. Gliomastix gueg was recognized to produce high levels of the enzyme. The optimum fermentation conditions for uricase production by Gliomastix gueg were examined. Results showed that uric acid medium was the most favorable one, the optimum temperature was at 30ºC, and incubation period required for maximum production was 8 days with aeration level at 150 rpm and at pH 8.0. Sucrose proved to be the best carbon source, uric acid was found to be the best nitrogen source. Both, dipotassium hydrogen phosphate and ferrous chloride as well as some vitamins gave the highest amount of uricase by Gliomastix gueg.

Optimum dietary protein requirement of genetically male tilapia ...

African Journals Online (AJOL)

The study was conducted to investigate the optimum dietary protein level needed for growing genetically male tilapia, Oreochromis niloticus. Diets containing crude protein levels 40, 42.5, 45, 47.5 and 50% were formulated and tried in triplicates. Test diets were fed to 20 fish/1m3 floating hapa at 5% of fish body weight daily ...

Optimum design of cogeneration system for nuclear seawater desalination - 15272

International Nuclear Information System (INIS)

Jung, Y.H.; Jeong, Y.H.

2015-01-01

A nuclear desalination process, which uses the energy released by nuclear fission, has less environmental impact and is generally cost-competitive with a fossil-fuel desalination process. A reference cogeneration system focused on in this study is the APR-1400 coupled with a MED (multi-effect distillation) process using the thermal vapor compression (TVC) technology. The thermal condition of the heat source is the most crucial factor that determines the desalination performance, i.e. energy consumption or freshwater production, of the MED-TVC process. The MED-TVC process operating at a higher motive steam pressure clearly shows a higher desalination performance. However, this increased performance does not necessarily translate to an advantage over processes operated at lower motive steam pressures. For instance, a higher motive steam pressure will increase the heat cost resulting from larger electricity generation loss, and thus may make this process unfavorable from an economic point of view. Therefore, there exists an optimum design point in the coupling configuration that makes the nuclear cogeneration system the most economical. This study is mainly aimed at investigating this optimum coupling design point of the reference nuclear cogeneration system using corresponding analysis tools. The following tools are used: MEE developed by the MEDRC for desalination performance analysis of the MED-TVC process, DE-TOP and DEEP developed by the IAEA for modeling of coupling configuration and economic evaluation of the nuclear cogeneration system, respectively. The results indicate that steam extraction from the MS exhaust and condensate return to HP FWHTR 5 is the most economical coupling design

Optimum Performance-Based Seismic Design Using a Hybrid Optimization Algorithm

Directory of Open Access Journals (Sweden)

S. Talatahari

2014-01-01

Full Text Available A hybrid optimization method is presented to optimum seismic design of steel frames considering four performance levels. These performance levels are considered to determine the optimum design of structures to reduce the structural cost. A pushover analysis of steel building frameworks subject to equivalent-static earthquake loading is utilized. The algorithm is based on the concepts of the charged system search in which each agent is affected by local and global best positions stored in the charged memory considering the governing laws of electrical physics. Comparison of the results of the hybrid algorithm with those of other metaheuristic algorithms shows the efficiency of the hybrid algorithm.

Determination of Optimum Compression Ratio: A Tribological Aspect

Directory of Open Access Journals (Sweden)

L. Yüksek

2013-12-01

Full Text Available Internal combustion engines are the primary energy conversion machines both in industry and transportation. Modern technologies are being implemented to engines to fulfill today's low fuel consumption demand. Friction energy consumed by the rubbing parts of the engines are becoming an important parameter for higher fuel efficiency. Rate of friction loss is primarily affected by sliding speed and the load acting upon rubbing surfaces. Compression ratio is the main parameter that increases the peak cylinder pressure and hence normal load on components. Aim of this study is to investigate the effect of compression ratio on total friction loss of a diesel engine. A variable compression ratio diesel engine was operated at four different compression ratios which were "12.96", "15:59", "18:03", "20:17". Brake power and speed was kept constant at predefined value while measuring the in- cylinder pressure. Friction mean effective pressure ( FMEP data were obtained from the in cylinder pressure curves for each compression ratio. Ratio of friction power to indicated power of the engine was increased from 22.83% to 37.06% with varying compression ratio from 12.96 to 20:17. Considering the thermal efficiency , FMEP and maximum in- cylinder pressure optimum compression ratio interval of the test engine was determined as 18.8 ÷ 19.6.

Low-level wind response to mesoscale pressure systems

Science.gov (United States)

Garratt, J. R.; Physick, W. L.

1983-09-01

Observations are presented which show a strong correlation between low-level wind behaviour (e.g., rotation near the surface) and the passage of mesoscale pressure systems. The latter are associated with frontal transition zones, are dominated by a pressure-jump line and a mesoscale high pressure area, and produce locally large horizontal pressure gradients. The wind observations are simulated by specifying a time sequence of perturbation pressure gradient and subsequently solving the vertically-integrated momentum equations with appropriate initial conditions. Very good agreement is found between observed and calculated winds; in particular, (i) a 360 ° rotation in wind on passage of the mesoscale high; (ii) wind-shift lines produced dynamically by the pressure-jump line; (iii) rapid linear increase in wind speed on passage of the pressure jump.

WHAT IS THE OPTIMUM SIZE OF GOVERNMENT: A SUGGESTION

Directory of Open Access Journals (Sweden)

Aykut Ekinci

2011-01-01

Full Text Available What is the optimum size of government? When the rule of law and the establishment of private property rights are taken into consideration, it is clear that the answer will not be at some 0%. On the other hand, when the experience of the old Soviet Union, East Germany and North Korea is considered, the answer will not be at some 100% either. Therefore, extreme points should not be the right answer. This study offers using normal distribution to answer this question. The study has revealed the following findings: (i The total amount of public expenditures as % of GDP, a is at minimum level at 4.55% rate, b is at optimum level at 13.4% rate, c is at maximum level at 31.7%. (ii Thus, as a fiscal rule, countries should: a choose the total amount of public expenditures as % of GDP ≤ 31.7% b target 13.4%. (iii Tree dimensional (3D normal distribution demonstrates that a healthy market system could be built upon a healthy government system (iv This approach rejects Wagner’s law. In a healthy growing economy, optimum government size could be kept at 13.4%. (v The UK, the USA and the European countries have been in the Keynesian-Marxist area, which reduces their average growth.

The relationship between PMI (manA) gene expression and optimal selection pressure in Indica rice transformation.

Science.gov (United States)

Gui, Huaping; Li, Xia; Liu, Yubo; Han, Kai; Li, Xianggan

2014-07-01

An efficient mannose selection system was established for transformation of Indica cultivar IR58025B . Different selection pressures were required to achieve optimum transformation frequency for different PMI selectable marker cassettes. This study was conducted to establish an efficient transformation system for Indica rice, cultivar IR58025B. Four combinations of two promoters, rice Actin 1 and maize Ubiquitin 1, and two manA genes, native gene from E. coli (PMI-01) and synthetic maize codon-optimized gene (PMI-09) were compared under various concentrations of mannose. Different selection pressures were required for different gene cassettes to achieve corresponding optimum transformation frequency (TF). Higher TFs as 54 and 53% were obtained when 5 g/L mannose was used for selection of prActin-PMI-01 cassette and 7.5 g/L mannose used for selection of prActin-PMI-09, respectively. TFs as 67 and 56% were obtained when 7.5 and 15 g/L mannose were used for selection of prUbi-PMI-01 and prUbi-PMI-09, respectively. We conclude that higher TFs can be achieved for different gene cassettes when an optimum selection pressure is applied. By investigating the PMI expression level in transgenic calli and leaves, we found there was a significant positive correlation between the protein expression level and the optimal selection pressure. Higher optimal selection pressure is required for those constructs which confer higher expression of PMI protein. The single copy rate of those transgenic events for prActin-PMI-01 cassette is lower than that for other three cassettes. We speculate some of low copy events with low protein expression levels might not have been able to survive in the mannose selection.

Optimum coolant chemistry in BWRs

International Nuclear Information System (INIS)

Lin, C.C.; Cowan, R.L.; Kiss, E.

2004-01-01

LWR water chemistry parameters are directly or indirectly related to the plant's operational performance and for a significant amount of Operation and Maintenance (O and M) costs. Obvious impacts are the operational costs associated with water treatment, monitoring and associated radwaste generation. Less obvious is the important role water chemistry plays in the magnitude of drywell shutdown dose rates, fuel corrosion performance and, (probably most importantly) materials degradation such as from stress corrosion cracking of piping and Reactor Pressure Vessel (RPV) internal components. To improve the operational excellence of the BWR and to minimize the impact of water chemistry on O and M costs. General Electric has developed the concept of Optimum Water Chemistry (OWC). The 'best practices' and latest technology findings from the U.S., Asia and Europe are integrated into the suggested OWC Specification. This concept, together with cost effective ways to meet the requirement, are discussed. (author)

Search for an optimum time response of spark counters

International Nuclear Information System (INIS)

Devismes, A.; Finck, Ch.; Kress, T.; Gobbi, A.; Eschke, J.; Herrmann, N.; Hildenbrand, K.D.; Koczon, P.; Petrovici, M.

2002-01-01

A spark counter of the type developed by Pestov has been tested with the aim of searching for an optimum time response function, changing voltage, content of noble and quencher gases, pressure and energy-loss. Replacing the usual argon by neon has brought an improvement of the resolution and a significant reduction of tails in the time response function. It has been proven that a counter as long as 90 cm can deliver, using neon gas mixture, a time resolution σ<60 ps with about 1% absolute tail and an efficiency of about 90%

Optimum design and thermodynamic analysis of a gas turbine and ORC combined cycle with recuperators

International Nuclear Information System (INIS)

Cao, Yue; Gao, Yike; Zheng, Ya; Dai, Yiping

2016-01-01

Highlights: • A GT-ORC combined cycle with recuperators was designed. • The effect of the ORC turbine inlet pressure on the combined cycle was examined. • Toluene was a more suitable working fluid for the GT-ORC combined cycle. • The GT-ORC combined cycle performed better than the GT-Rankine combined cycle. • The sensitivity analysis to the ambient temperature was completed. - Abstract: Gas turbines are widely used in distributed power generation because of their high efficiency, low pollution and low operational cost. To further utilize the waste heat from gas turbines, an organic Rankine cycle (ORC) was proposed as the bottoming cycle for gas turbines in this paper. Two recuperators were coupled with the combined cycle to increase the thermal efficiency, and aromatics were chosen as the working fluid for the bottoming cycle. This paper focused on the optimum design and thermodynamic analysis of the gas turbine and ORC (GT-ORC) combined cycle. Results showed that the net power and thermal efficiency of the ORC increased with the ORC turbine inlet pressure and achieved optimum values at a specific pressure based on the optimum criteria. Furthermore, compared with the GT-Rankine combined cycle, the GT-ORC combined cycle had better thermodynamic performance. Toluene was a more suitable working fluid for the GT-ORC combined cycle. Moreover, ambient temperature sensitivity simulations concluded that the GT-ORC combined cycle had a maximum thermal efficiency and the combined cycle net power was mainly determined by the topping gas turbine cycle.

Atmospheric Pressure Effect of Retained Gas in High Level Waste

International Nuclear Information System (INIS)

Weber, A.H.

1999-01-01

Isolated high level waste tanks in H-Area have unexplained changes in waste-level which have been attributed to environmental effects including pressure, temperature, and relative humidity. Previous studies at SRS have considered waste-level changes from causes not including the presence of gas in the salt cake. This study was undertaken to determine the effect of atmospheric pressure on gas in the salt cake and resultant changes in the supernate level of Tank 41H, and to model that effect if possible. A simple theory has been developed to account for changes in the supernate level in a high level waste tank containing damp salt cake as the response of trapped gases to changes in the ambient pressure. The gas is modeled as an ideal gas retained as bubbles within the interstitial spaces in the salt cake and distributed uniformly throughout the tank. The model does not account for consistent long term increases or decreases in the tank level. Any such trend in the tank level is attributed to changes in the liquid content in the tank (from condensation, evaporation, etc.) and is removed from the data prior to the void estimation. Short term fluctuations in the tank level are explained as the response of the entrained gas volume to changes in the ambient pressure. The model uses the response of the tank level to pressure changes to estimate an average void fraction for the time period of interest. This estimate of the void is then used to predict the expected level response. The theory was applied to three separate time periods of the level data for tank 41H as follows: (1) May 3, 1993 through August 3, 1993, (2) January 23, 1994 through April 21, 1994, and (3) June 4, 1994 through August 24, 1994. A strong correlation was found between fluctuations in the tank level and variations in the ambient pressure. This correlation is a clear marker of the presence of entrained gases in the tank. From model calculations, an average void fraction of 11 percent was estimated to

Blood pressure response to low level static contractions

DEFF Research Database (Denmark)

Fallentin, Nils; Jørgensen, Kurt

1992-01-01

The present study re-examines the 15% MVC concept, i.e. the existence of a circulatory steady-state in low intensity static contractions below 15% of maximal voluntary contraction (MVC). Mean arterial blood pressure was studied during static endurance contractions of the elbow flexor and extensor...... 0.7) min for elbow extension]. Mean arterial blood pressure exhibited a continuous and progressive increase during the 10% MVC contractions indicating that the 15% MVC concept would not appear to be valid. The terminal blood pressure value recorded at the point of exhaustion in the 10% MVC elbow...... the circulation to the muscles was arrested just prior to the cessation of the contraction, blood pressure only partly recovered and remained elevated for as long as the occlusion persisted, indicating the level of pressure-raising muscle chemoreflexes. Based on blood pressure recordings obtained during...

Optimum Drafting Conditions Of Polyester And Viscose Blend Yarns

Directory of Open Access Journals (Sweden)

Hatamvand Mohammad

2017-09-01

Full Text Available In this study, we used an experimental design to investigate the influence of the total draft, break draft, distance between the aprons (Clips and production roller pressure on yarn quality in order to obtain optimum drafting conditions for polyester and viscose (PES/CV blend yarns in ring spinning frame. We used PES fibers (1.4 dtex × 38 mm long and CV fibers (1.6 dtex × 38 mm long to spin a 20 Tex blend yarn of PES (70%/CV (30% blend ratio. When the break draft, adjustment of distance between of aprons and roller pressure is not reasonable, controlling and leading of the fibers is not sufficient for proper orientation of the fibers in the yarn structure to produce a high quality yarn. Experimental results and statistical analysis show that the best yarn quality will be obtained under drafting conditions total draft of 38, 1.2 break draft, 2.8 mm distance between of aprons and maximum pressure of the production top roller (18daN.

Detection of human influence on sea-level pressure.

Science.gov (United States)

Gillett, Nathan P; Zwiers, Francis W; Weaver, Andrew J; Stott, Peter A

2003-03-20

Greenhouse gases and tropospheric sulphate aerosols--the main human influences on climate--have been shown to have had a detectable effect on surface air temperature, the temperature of the free troposphere and stratosphere and ocean temperature. Nevertheless, the question remains as to whether human influence is detectable in any variable other than temperature. Here we detect an influence of anthropogenic greenhouse gases and sulphate aerosols in observations of winter sea-level pressure (December to February), using combined simulations from four climate models. We find increases in sea-level pressure over the subtropical North Atlantic Ocean, southern Europe and North Africa, and decreases in the polar regions and the North Pacific Ocean, in response to human influence. Our analysis also indicates that the climate models substantially underestimate the magnitude of the sea-level pressure response. This discrepancy suggests that the upward trend in the North Atlantic Oscillation index (corresponding to strengthened westerlies in the North Atlantic region), as simulated in a number of global warming scenarios, may be too small, leading to an underestimation of the impacts of anthropogenic climate change on European climate.

Thermal performance analysis and optimum design parameters of heat exchanger having perforated pin fins

International Nuclear Information System (INIS)

Sahin, Bayram; Demir, Alparslan

2008-01-01

This paper reports the heat transfer enhancement and corresponding pressure drop over a flat surface equipped with circular cross section perforated pin fins in a rectangular channel. The channel had a cross section area of 100-250 mm 2 . The experiments covered the following ranges: Reynolds number 13500-42,000, clearance ratio (C/H) 0, 0.33 and 1 and interfin spacing ratio (S y /D) 1.208, 1.524, 1.944 and 3.417. Correlation equations were developed for the heat transfer, friction factor and enhancement efficiency. The experimental results showed that the use of circular cross section pin fins may lead to heat transfer enhancement. Enhancement efficiencies varied between 1.4 and 2.6 depending on clearance ratio and interfin spacing ratio. Using a Taguchi experimental design method, optimum design parameters and their levels were investigated. Nusselt number and friction factor were considered as performance parameters. An L 9 (3 3 ) orthogonal array was selected as an experimental plan. First of all, each goal was optimized separately. Then, all the goals were optimized together, considering the priority of the goals, and the optimum results were found to be Reynolds number of 42,000, fin height of 50 mm and streamwise distance between fins of 51 mm

The effect of pressurizer-water-level on the low frequency component of the pressure spectrum in a PWR

International Nuclear Information System (INIS)

Por, G.; Izsak, E.; Valko, J.

1984-09-01

The pressure fluctuations were measured in the cooling system of the Paks-1 reactor. A shift of the peak was detected in low frequency component of the pressure fluctuation spectrum which is due to the fluctuations of water level in the pressurizer. Using the model of Katona and Nagy (1983), the eigenfrequencies, the magnitude of the shift and the sensitivity to the pressurizer water level were reproduced in good accordance with the experimental data. (D.Gy.)

HOPG/ZnO/HOPG pressure sensor

Science.gov (United States)

Jahangiri, Mojtaba; Yousefiazari, Ehsan; Ghalamboran, Milad

2017-12-01

Pressure sensor is one of the most commonly used sensors in the research laboratories and industries. These are generally categorized in three different classes of absolute pressure sensors, gauge pressure sensors, and differential pressure sensors. In this paper, we fabricate and assess the pressure sensitivity of the current vs. voltage diagrams in a graphite/ZnO/graphite structure. Zinc oxide layers are deposited on highly oriented pyrolytic graphite (HOPG) substrates by sputtering a zinc target under oxygen plasma. The top electrode is also a slice of HOPG which is placed on the ZnO layer and connected to the outside electronic circuits. By recording the I-V characteristics of the device under different forces applied to the top HOPG electrode, the pressure sensitivity is demonstrated; at the optimum biasing voltage, the device current changes 10 times upon changing the pressure level on the top electrode by 20 times. Repeatability and reproducibility of the observed effect is studied on the same and different samples. All the materials used for the fabrication of this pressure sensor are biocompatible, the fabricated device is anticipated to find potential applications in biomedical engineering.

A portable anaerobic microbioreactor reveals optimum growth conditions for the methanogen Methanosaeta concilii.

Science.gov (United States)

Steinhaus, Benjamin; Garcia, Marcelo L; Shen, Amy Q; Angenent, Largus T

2007-03-01

Conventional studies of the optimum growth conditions for methanogens (methane-producing, obligate anaerobic archaea) are typically conducted with serum bottles or bioreactors. The use of microfluidics to culture methanogens allows direct microscopic observations of the time-integrated response of growth. Here, we developed a microbioreactor (microBR) with approximately 1-microl microchannels to study some optimum growth conditions for the methanogen Methanosaeta concilii. The microBR is contained in an anaerobic chamber specifically designed to place it directly onto an inverted light microscope stage while maintaining a N2-CO2 environment. The methanogen was cultured for months inside microchannels of different widths. Channel width was manipulated to create various fluid velocities, allowing the direct study of the behavior and responses of M. concilii to various shear stresses and revealing an optimum shear level of approximately 20 to 35 microPa. Gradients in a single microchannel were then used to find an optimum pH level of 7.6 and an optimum total NH4-N concentration of less than 1,100 mg/liter (<47 mg/liter as free NH3-N) for M. concilii under conditions of the previously determined ideal shear stress and pH and at a temperature of 35 degrees C.

Type GQS-1 high pressure steam manifold water level monitoring system

International Nuclear Information System (INIS)

Li Nianzu; Li Beicheng; Jia Shengming

1993-10-01

The GQS-1 high pressure steam manifold water level monitoring system is an advanced nuclear gauge that is suitable for on-line detecting and monitor in high pressure steam manifold water level. The physical variable of water level is transformed into electrical pulses by the nuclear sensor. A computer is equipped for data acquisition, analysis and processing and the results are displayed on a 14 inch color monitor. In addition, a 4 ∼ 20 mA output current is used for the recording and regulation of water level. The main application of this gauge is for on-line measurement of high pressure steam manifold water level in fossil-fired power plant and other industries

OPTIMUM PROSESSENTRERING

Directory of Open Access Journals (Sweden)

K. Adendorff

2012-01-01

Full Text Available

ENGLISH ABSTRACT: The paper derives an expression for optimum process centreing for a given design specification and spoilage and/or rework costs.

AFRIKAANSE OPSOMMING: Die problem Van prosessentrering vir n gegewe ontwerpspesifikasie en herwerk- en/of skrootkoste word behandel.

Application of adaptive fuzzy control technology to pressure control of a pressurizer

Institute of Scientific and Technical Information of China (English)

YANG Ben-kun; BIAN Xin-qian; GUO Wei-lai

2005-01-01

A pressurizer is one of important equipment in a pressurized water reactor plant. It is used to maintain the pressure of primary coolant within allowed range because the sharp change of coolant pressure affects the security of reactor,therefor,the study of pressurizer's pressure control methods is very important. In this paper, an adaptive fuzzy controller is presented for pressure control of a pressurizer in a nuclear power plant. The controller can on-line tune fuzzy control rules and parameters by self-learning in the actual control process, which possesses the way of thinking like human to make a decision. The simulation results for a pressurized water reactor plant show that the adaptive fuzzy controller has optimum and intelligent characteristics, which prove the controller is effective.

Buried Object Detection Method Using Optimum Frequency Range in Extremely Shallow Underground

Science.gov (United States)

Sugimoto, Tsuneyoshi; Abe, Touma

2011-07-01

We propose a new detection method for buried objects using the optimum frequency response range of the corresponding vibration velocity. Flat speakers and a scanning laser Doppler vibrometer (SLDV) are used for noncontact acoustic imaging in the extremely shallow underground. The exploration depth depends on the sound pressure, but it is usually less than 10 cm. Styrofoam, wood (silver fir), and acrylic boards of the same size, different size styrofoam boards, a hollow toy duck, a hollow plastic container, a plastic container filled with sand, a hollow steel can and an unglazed pot are used as buried objects which are buried in sand to about 2 cm depth. The imaging procedure of buried objects using the optimum frequency range is given below. First, the standardized difference from the average vibration velocity is calculated for all scan points. Next, using this result, underground images are made using a constant frequency width to search for the frequency response range of the buried object. After choosing an approximate frequency response range, the difference between the average vibration velocity for all points and that for several points that showed a clear response is calculated for the final confirmation of the optimum frequency range. Using this optimum frequency range, we can obtain the clearest image of the buried object. From the experimental results, we confirmed the effectiveness of our proposed method. In particular, a clear image of the buried object was obtained when the SLDV image was unclear.

Improving boiler unit performance using an optimum robust minimum-order observer

International Nuclear Information System (INIS)

Moradi, Hamed; Bakhtiari-Nejad, Firooz

2011-01-01

Research highlights: → Multivariable model of a boiler unit with uncertainty. → Design of a robust minimum-order observer. → Developing an optimal functional code in MATLAB environment. → Finding optimum region of observer-based controller poles. → Guarantee of robust performance in the presence of parametric uncertainties. - Abstract: To achieve a good performance of the utility boiler, dynamic variables such as drum pressure, steam temperature and water level of drum must be controlled. In this paper, a linear time invariant (LTI) model of a boiler system is considered in which the input variables are feed-water and fuel mass rates. Due to the inaccessibility of some state variables of boiler system, a minimum-order observer is designed based on Luenberger's model to gain an estimate state x-tilde of the true state x. Low cost of design and high accuracy of states estimation are the main advantages of the minimum-order observer; in comparison with previous designed full-order observers. By applying the observer on the closed-loop system, a regulator system is designed. Using an optimal functional code developed in MATLAB environment, desired observer poles are found such that suitable time response specifications of the boiler system are achieved and the gain and phase margin values are adjusted in an acceptable range. However, the real dynamic model may associate with parametric uncertainties. In that case, optimum region of poles of observer-based controller are found such that the robust performance of the boiler system against model uncertainties is guaranteed.

CT4 - Cost-Optimum Procedures

DEFF Research Database (Denmark)

Thomsen, Kirsten Engelund; Wittchen, Kim Bjarne

This report collects the status in European member states regarding implementation of the cos optimum procedure for setting energy performance requirements to new and existing buildings.......This report collects the status in European member states regarding implementation of the cos optimum procedure for setting energy performance requirements to new and existing buildings....

The optimum lead thickness for lead-activation detectors

International Nuclear Information System (INIS)

Si Fenni; Hu Qingyuan

2009-01-01

The optimum lead thickness for lead-activation detectors has been studied in this paper. First existence of the optimum lead thickness is explained theoretically. Then the optimum lead thickness is obtained by two methods, MCNP5 calculation and mathematical estimation. At last factors which affect the optimum lead thickness are discussed. It turns out that the optimum lead thickness is irrelevant to incident neutron energies. It is recommended 2.5 cm generally.

Particle contamination in gas-insulated systems: new control methods and optimum SF6/N2 mixtures

International Nuclear Information System (INIS)

Pace, M.O.; Adcock, J.L.; Christophorou, L.G.

1984-01-01

The feasibilities of two new separate techniques to control particle contamination in practical gas-insulated sytems were tested in a small-scale concentric cylinder geometry. In one technique an insulating coating was first formed on the particles in a contaminated system by low-pressure discharges in appropriate gases such as 1-C 3 F 6 and c-C 4 F 8 . When SF 6 was subsequently introduced into the same system at practical pressure as the operating insulation, the considerable harm ordinarily caused by particles was found to be eliminated. The nature of the coating formed also on the electrodes in this process was studied, with the conclusion that the observed benefits were primarily due to coating on particles, not on electrodes. In the second technique the particles, moved randomly by electrical stress, struck and adhered to the surface of a tacky insulating solid material; they were subsequently encapsulated in a melt-resolidify cycle without electrical stress. This trapping technique was also found to eliminate the harmful effects of particles in SF 6 at practical pressure. A technique for producing a trapping material with temperature characteristics appropriate for practical apparatus was devised. The effect of particle contamination on the dielectric strength of SF 6 /N 2 mixtures was studied as a function of total pressure and percentage of each gas. Optimum total pressure (approx. 6 atm) and optimum percentages (60% SF 6 /40% N 2 ) were observed in breakdown tests in particle-contaminated concentric cylinder geometry

Optimum Discharge Burnup and Cycle Length for PWRs

International Nuclear Information System (INIS)

Secker, Jeffrey R.; Johansen, Baard J.; Stucker, David L.; Ozer, Odelli; Ivanov, Kostadin; Yilmaz, Serkan; Young, E.H.

2005-01-01

This paper discusses the results of a pressurized water reactor fuel management study determining the optimum discharge burnup and cycle length. A comprehensive study was performed considering 12-, 18-, and 24-month fuel cycles over a wide range of discharge burnups. A neutronic study was performed followed by an economic evaluation. The first phase of the study limited the fuel enrichments used in the study to 235 U consistent with constraints today. The second phase extended the range of discharge burnups for 18-month cycles by using fuel enriched in excess of 5 wt%. The neutronic study used state-of-the-art reactor physics methods to accurately determine enrichment requirements. Energy requirements were consistent with today's high capacity factors (>98%) and short (15-day) refueling outages. The economic evaluation method considers various component costs including uranium, conversion, enrichment, fabrication and spent-fuel storage costs as well as the effect of discounting of the revenue stream. The resulting fuel cycle costs as a function of cycle length and discharge burnup are presented and discussed. Fuel costs decline with increasing discharge burnup for all cycle lengths up to the maximum discharge burnup considered. The choice of optimum cycle length depends on assumptions for outage costs

Design chart of optimum current leads

International Nuclear Information System (INIS)

Ishibashi, K.; Katase, A.; Maechata, K.

1986-01-01

The heat flow through current leads is one of major heat losses in a superconducting magnet system. To reduce the heat flow, current leads have been optimized in a complex way by varying such quantities as conductor length, cross-sectional area, heat transfer coefficient and cooling perimeter. Therefore, this study is made to simplify the design procedure, and to explain the general characteristics of the current leads. A new combined parameter which takes turbulent flow into account is introduced in the present work to enable us to draw a useful design chart. This chart gives, to a wide variety of current leads, detailed information about the optimum design-viz. geometric dimensions, heat flow into liquid helium, and pressure drop of the cooling gas. Change of the cross-sectional area along the conductor may improve the current lead performance. The effects of this area change are examined in detail

Probabilistic studies for safety at optimum cost

International Nuclear Information System (INIS)

Pitner, P.

1999-01-01

By definition, the risk of failure of very reliable components is difficult to evaluate. How can the best strategies for in service inspection and maintenance be defined to limit this risk to an acceptable level at optimum cost? It is not sufficient to design structures with margins, it is also essential to understand how they age. The probabilistic approach has made it possible to develop well proven concepts. (author)

Optimum level of salt in French-type bread. Influence of income status, salt level in daily bread consumption, and test location.

Science.gov (United States)

Sosa, M; Flores, A; Hough, G; Apro, N; Ferreyra, V; Orbea, M M

2008-10-01

The objectives of the present study were to measure the ideal salt concentration in French-type bread among Argentine consumers in a home-usage-test (HUT) considering income status and salt content of daily bread consumption as covariables, and to compare the ideal salt concentrations measured in a HUT and a central-location test (CLT). For the HUT, 420 consumers each received a sample of bread with a single salt concentration, and for the CLT, 100 consumers each received 7 samples with different salt concentrations. For each sample, consumers responded if they found the bread "not-salty-enough,"okay," or "too-salty." Neither income level nor salt content of daily bread influenced probability of rejection. The optimum sodium concentrations (milligrams per 100 g of bread dry basis) +/- 95% confidence limits for the HUT and CLT were 980 +/- 74 and 1157 +/- 87, respectively. These values are substantially higher than 628, the mean sodium content of the bread sampled from the bakery shops where consumers bought their daily bread.

Optimum profit model considering production, quality and sale problem

Science.gov (United States)

Chen, Chung-Ho; Lu, Chih-Lun

2011-12-01

Chen and Liu ['Procurement Strategies in the Presence of the Spot Market-an Analytical Framework', Production Planning and Control, 18, 297-309] presented the optimum profit model between the producers and the purchasers for the supply chain system with a pure procurement policy. However, their model with a simple manufacturing cost did not consider the used cost of the customer. In this study, the modified Chen and Liu's model will be addressed for determining the optimum product and process parameters. The authors propose a modified Chen and Liu's model under the two-stage screening procedure. The surrogate variable having a high correlation with the measurable quality characteristic will be directly measured in the first stage. The measurable quality characteristic will be directly measured in the second stage when the product decision cannot be determined in the first stage. The used cost of the customer will be measured by adopting Taguchi's quadratic quality loss function. The optimum purchaser's order quantity, the producer's product price and the process quality level will be jointly determined by maximising the expected profit between them.

Relationship between systemic hemodynamics and ambulatory blood pressure level are sex dependent.

Science.gov (United States)

Alfie, J; Waisman, G D; Galarza, C R; Magi, M I; Vasvari, F; Mayorga, L M; Cámera, M I

1995-12-01

Sex-related differences in systemic hemodynamics were analyzed by means of cardiac index and systemic vascular resistance according to the level of daytime ambulatory blood pressure. In addition, we assessed the relations between ambulatory blood pressure measurements and systemic hemodynamics in male and female patients. We prospectively included 52 women and 53 men referred to our unit for evaluation of arterial hypertension. Women and men were grouped according to the level of daytime mean arterial pressure: or = 110 mm Hg. Patients underwent noninvasive evaluation of resting hemodynamics (impedance cardiography) and 24-hour ambulatory blood pressure monitoring. Compared with women men with lower daytime blood pressure had a 12% higher systemic vascular resistance index (P = NS) and a 14% lower cardiac index (P < .02), whereas men with higher daytime blood pressure had a 25% higher vascular resistance (P < .003) and a 21% lower cardiac index (P < .0004). Furthermore, in men systemic vascular resistance correlated positively with both daytime and nighttime systolic and diastolic blood pressures, whereas cardiac index correlated negatively only with daytime diastolic blood pressure. In contrast, women did not exhibit any significant correlation between hemodynamic parameters and ambulatory blood pressure measurements. In conclusion, sex-related differences in systemic hemodynamics were more pronounced in the group with higher daytime hypertension. The relations between systemic hemodynamics and ambulatory blood pressure level depended on the sex of the patient. In men a progressive circulatory impairment underlies the increasing level of ambulatory blood pressure, but this was not observed in women.

Levels of Assertiveness and Peer Pressure of Nursing Students

Directory of Open Access Journals (Sweden)

Esin Arslan

2013-01-01

Full Text Available Background: The research was conducted in order to determine levels of assertiveness and peer pressure of the nursing students.Methodology: This descriptive research has been performed with 154 nursing students in Bozok University, The data were collected with Questionnaire Form, Rathus Assertiveness Inventory and Peer Pressure Scale. We used the data one way Anova, two samples t test, the relationship between several independent variables and scales were evaluated by Pearson correlation technique in order to evaluate the data with normal distribution.Results: It was seen that 69.5% of the students was assertive and mean scores for assertiveness of the male students (19.4±17.9 were higher than that of the female students (29.0±14.1. However, mean scores for peer pressure of the male students (56.6±12.4 were higher than that of the female students (44.0±8.8. It was found out that there was a positive direction middle level significant correlation between mean assertiveness scores and mean peer pressure scores of the studentsConclusion: Although we did not find any significant correlation between mean assertiveness scores and mean peer pressure scores, it was seen that male students were more assertive than female students and male students experienced peer pressure more than female students.

Optimum concrete compression strength using bio-enzyme

Directory of Open Access Journals (Sweden)

Bagio Tony Hartono

2017-01-01

Full Text Available To make concrete with high compressive strength and has a certain concrete specifications other than the main concrete materials are also needed concrete mix quality control and other added material is also in line with the current technology of concrete mix that produces concrete with specific characteristics. Addition of bio enzyme on five concrete mixture that will be compared with normal concrete in order to know the optimum level bio-enzyme in concrete to increase the strength of the concrete. Concrete with bio-enzyme 200 ml/m3, 400 ml/m3, 600 ml/m3, 800 ml/m3, 1000 ml/m3 and normal concrete. Refer to the crushing test result, its tends to the mathematical model using 4th degree polynomial regression (least quartic, as represent on the attached data series, which is for the design mix fc′ = 25 MPa generate optimum value for 33,98 MPa, on the bio-additive dosage of 509 ml bio enzymes.

An analysis of collegiate band directors' exposure to sound pressure levels

Science.gov (United States)

Roebuck, Nikole Moore

Noise-induced hearing loss (NIHL) is a significant but unfortunate common occupational hazard. The purpose of the current study was to measure the magnitude of sound pressure levels generated within a collegiate band room and determine if those sound pressure levels are of a magnitude that exceeds the policy standards and recommendations of the Occupational Safety and Health Administration (OSHA), and the National Institute of Occupational Safety and Health (NIOSH). In addition, reverberation times were measured and analyzed in order to determine the appropriateness of acoustical conditions for the band rehearsal environment. Sound pressure measurements were taken from the rehearsal of seven collegiate marching bands. Single sample t test were conducted to compare the sound pressure levels of all bands to the noise exposure standards of OSHA and NIOSH. Multiple regression analysis were conducted and analyzed in order to determine the effect of the band room's conditions on the sound pressure levels and reverberation times. Time weighted averages (TWA), noise percentage doses, and peak levels were also collected. The mean Leq for all band directors was 90.5 dBA. The total accumulated noise percentage dose for all band directors was 77.6% of the maximum allowable daily noise dose under the OSHA standard. The total calculated TWA for all band directors was 88.2% of the maximum allowable daily noise dose under the OSHA standard. The total accumulated noise percentage dose for all band directors was 152.1% of the maximum allowable daily noise dose under the NIOSH standards, and the total calculated TWA for all band directors was 93dBA of the maximum allowable daily noise dose under the NIOSH standard. Multiple regression analysis revealed that the room volume, the level of acoustical treatment and the mean room reverberation time predicted 80% of the variance in sound pressure levels in this study.

Optimum Wing Shape of Highly Flexible Morphing Aircraft for Improved Flight Performance

Science.gov (United States)

Su, Weihua; Swei, Sean Shan-Min; Zhu, Guoming G.

2016-01-01

In this paper, optimum wing bending and torsion deformations are explored for a mission adaptive, highly flexible morphing aircraft. The complete highly flexible aircraft is modeled using a strain-based geometrically nonlinear beam formulation, coupled with unsteady aerodynamics and six-degrees-of-freedom rigid-body motions. Since there are no conventional discrete control surfaces for trimming the flexible aircraft, the design space for searching the optimum wing geometries is enlarged. To achieve high performance flight, the wing geometry is best tailored according to the specific flight mission needs. In this study, the steady level flight and the coordinated turn flight are considered, and the optimum wing deformations with the minimum drag at these flight conditions are searched by utilizing a modal-based optimization procedure, subject to the trim and other constraints. The numerical study verifies the feasibility of the modal-based optimization approach, and shows the resulting optimum wing configuration and its sensitivity under different flight profiles.

Enhancing the aggressive intensity of hydrodynamic cavitation through a Venturi tube by increasing the pressure in the region where the bubbles collapse

Science.gov (United States)

Soyama, H.; Hoshino, J.

2016-04-01

In this paper, we used a Venturi tube for generating hydrodynamic cavitation, and in order to obtain the optimum conditions for this to be used in chemical processes, the relationship between the aggressive intensity of the cavitation and the downstream pressure where the cavitation bubbles collapse was investigated. The acoustic power and the luminescence induced by the bubbles collapsing were investigated under various cavitating conditions, and the relationships between these and the cavitation number, which depends on the upstream pressure, the downstream pressure at the throat of the tube and the vapor pressure of the test water, was found. It was shown that the optimum downstream pressure, i.e., the pressure in the region where the bubbles collapse, increased the aggressive intensity by a factor of about 100 compared to atmospheric pressure without the need to increase the input power. Although the optimum downstream pressure varied with the upstream pressure, the cavitation number giving the optimum conditions was constant for all upstream pressures.

Enhancing the aggressive intensity of hydrodynamic cavitation through a Venturi tube by increasing the pressure in the region where the bubbles collapse

Directory of Open Access Journals (Sweden)

H. Soyama

2016-04-01

Full Text Available In this paper, we used a Venturi tube for generating hydrodynamic cavitation, and in order to obtain the optimum conditions for this to be used in chemical processes, the relationship between the aggressive intensity of the cavitation and the downstream pressure where the cavitation bubbles collapse was investigated. The acoustic power and the luminescence induced by the bubbles collapsing were investigated under various cavitating conditions, and the relationships between these and the cavitation number, which depends on the upstream pressure, the downstream pressure at the throat of the tube and the vapor pressure of the test water, was found. It was shown that the optimum downstream pressure, i.e., the pressure in the region where the bubbles collapse, increased the aggressive intensity by a factor of about 100 compared to atmospheric pressure without the need to increase the input power. Although the optimum downstream pressure varied with the upstream pressure, the cavitation number giving the optimum conditions was constant for all upstream pressures.

Analysis of sound pressure levels emitted by children's toys.

Science.gov (United States)

Sleifer, Pricila; Gonçalves, Maiara Santos; Tomasi, Marinês; Gomes, Erissandra

2013-06-01

To verify the levels of sound pressure emitted by non-certified children's toys. Cross-sectional study of sound toys available at popular retail stores of the so-called informal sector. Electronic, mechanical, and musical toys were analyzed. The measurement of each product was carried out by an acoustic engineer in an acoustically isolated booth, by a decibel meter. To obtain the sound parameters of intensity and frequency, the toys were set to produce sounds at a distance of 10 and 50cm from the researcher's ear. The intensity of sound pressure [dB(A)] and the frequency in hertz (Hz) were measured. 48 toys were evaluated. The mean sound pressure 10cm from the ear was 102±10 dB(A), and at 50cm, 94±8 dB(A), with ptoys was above 85dB(A). The frequency ranged from 413 to 6,635Hz, with 56.3% of toys emitting frequency higher than 2,000Hz. The majority of toys assessed in this research emitted a high level of sound pressure.

OPTIMUM LEVEL OF POSITIVE END-EXPIRATORY PRESSURE IN ACUTE RESPIRATORY DISTRESS SYNDROME CAUSED BY INFLUENZA A(H1NI)PDM09: BALANCE BETWEEN MAXIMAL END-EXPIRATORY VOLUME AND MINIMAL ALVEOLAR OVERDISTENSION.

Science.gov (United States)

Yaroshetskiym A I; Protsenko, D N; Boytsov, P V; Chentsov, V B; Nistratov, S L; Kudlyakov, O N; Solov'ev, V V; Banova, Zh I; Shkuratova, N V; Rezenov, N A; Gel'fand, B R

2016-11-01

to determine optimum level ofpositive end-expiratory pressure (PEEP) according to balance between maxi- mal end-expiratory lung volume (EEL V)(more than predicted) and minimal decrease in exhaled carbon dioxide volume (VCO) and then to develop the algorithm of gas exchange correction based on prognostic values of EEL K; alveolar recruitability, PA/FiO2, static compliance (C,,,) and VCO2. 27 mechanically ventilatedpatients with acute respiratory distress syndrome (ARDS) caused by influenza A (HINJ)pdm09 in Moscow Municipal Clinics ICU's from January to March 2016 were included in the trial. At the beginning of the study patients had the following characteristic: duration offlu symptoms 5 (3-10) days, p.0/FiO2 120 (70-50) mmHg. SOFA 7 (5-9), body mass index 30.1 (26.4-33.8) kg/m², static compliance of respiratory system 35 (30-40) ml/mbar: Under sedation and paralysis we measured EELV, C VCO and end-tidal carbon dioxide concentration (EtCO) (for CO₂ measurements we fixed short-term values after 2 min after PEEP level change) at PEEP 8, 11,13,15,18, 20 mbar consequently, and incase of good recruitability, at 22 and 24 mbar. After analyses of obtained data we determined PEEP value in which increase in EELV was maximal (more than predicted) and depression of VCO₂ was less than 20%, change in mean blood pressure and heart rate were both less than 20% (measured at PEEP 8 mbar). After that we set thus determined level of PEEP and didn't change it for 5 days. Comparision of predicted and measured EELV revealed two typical points of alveloar recruiment: the first at PEEP 11-15 mbar, the second at PEEP 20-22 mbar. EELV measured at PEEP 18 mbar appeared to be higher than predicted at PEEP 8 mbar by 400 ml (approx.), which was the sign of alveolar recruitment-1536 (1020-1845) ml vs 1955 (1360-2320) ml, p=0,001, Friedman test). we didn't found significant changes of VCO₂ when increased PEEP in the range from 8 to 15 mbar (p>0.05, Friedman test). PEEP increase from 15 to

CLASSICAL MUSIC DECREASE STRESS LEVEL AND BLOOD PRESSURE PRIMIGRAVIDA IN THE THIRD TRIMESTER

Directory of Open Access Journals (Sweden)

Ni Ketut Alit Armini

2017-07-01

Full Text Available Introduction: Many changes in psychology and biology increase primigravida’s stress in the third trimester. The stress response makes blood pressure being unstable, it causes bad effect for pregnancy. Classical music can be used as one of relaxation facilities that can reduce stress. The aimed of this study were to analyze the effect of classical music on stress level and blood pressure. Method: This study was used a quasy experimental purposive sampling design. The sample in this study were 14 pregnancy women in the third trimester in RSIA Cempaka Putih Permata Surabaya. The independent variable in this study was classical music and the dependent variable were stress level and blood pressure. Data were analyzed by Wilcoxon Signed Rank Test, Mann Withney U Test, Paired t Test and Independent t Test with significance level α≤0.05. Result: The result showed that the stress level in controlled group with p=0.567 and intervention group with p=0.025. The result of blood pressure in controlled group with p=0.522 in systolic blood pressure, p=0.35 in diastolic blood pressure and intervention group showed p=0.103 in systolic blood pressure and p=1.00 in diastolic blood pressure. Discussion: It can be concluded that listening classical music can reduce stress level, stabilize blood pressure, although blood pressure hasn’t significant result but mean of blood pressure show that it was stable. Further studies should be considered to used cortisol to identify stress biology response spesifically.

Patients' and clinicians' views on the optimum schedules for self-monitoring of blood pressure: a qualitative focus group and interview study.

Science.gov (United States)

Grant, Sabrina; Hodgkinson, James A; Milner, Siobhan L; Martin, Una; Tompson, Alice; Hobbs, Fd Richard; Mant, Jonathan; McManus, Richard J; Greenfield, Sheila M

2016-11-01

Self-monitoring of blood pressure is common but guidance on how it should be carried out varies and it is currently unclear how such guidance is viewed. To explore patients' and healthcare professionals' (HCPs) views and experiences of the use of different self-monitoring regimens to determine what is acceptable and feasible, and to inform future recommendations. Thirteen focus groups and four HCP interviews were held, with a total of 66 participants (41 patients and 25 HCPs) from primary and secondary care with and without experience of self-monitoring. Standard and shortened self-monitoring protocols were both considered. Focus groups and interviews were recorded, transcribed verbatim, and analysed using the constant comparative method. Patients generally supported structured schedules but with sufficient flexibility to allow adaptation to individual routine. They preferred a shorter (3-day) schedule to longer (7-day) regimens. Although HCPs could describe benefits for patients of using a schedule, they were reluctant to recommend a specific schedule. Concerns surrounded the use of different schedules for diagnosis and subsequent monitoring. Appropriate education was seen as vital by all participants to enable a self-monitoring schedule to be followed at home. There is not a 'one size fits all approach' to developing the optimum protocol from the perspective of users and those implementing it. An approach whereby patients are asked to complete the minimum number of readings required for accurate blood pressure estimation in a flexible manner seems most likely to succeed. Informative advice and guidance should incorporate such flexibility for patients and professionals alike. © British Journal of General Practice 2016.

Optimum dietary protein requirement of Malaysian mahseer (Tor tambroides) fingerling.

Science.gov (United States)

Misieng, Josephine Dorin; Kamarudin, Mohd Salleh; Musa, Mazlinda

2011-02-01

The optimum dietary protein requirement of the Malaysian mahseer (Tor tambroides) fingerlings was determined in this study. In this completely randomized designed experiment, formulated diets of five levels of dietary protein (30, 35, 40, 45 and 50%) were tested on the T. tambroides fingerlings (initial body weight of 5.85 +/- 0.40 g), reared in aquarium fitted with a biofiltering system. The fingerlings were fed twice daily at 5% of biomass. The fingerling body weight and total length was taken at every two weeks. Mortality was recorded daily. The dietary protein had significant effects on the body weight gain and Specific Growth Rate (SGR) of the fingerlings. The body weight gain and SGR of fingerlings fed with the diet with the dietary protein level of 40% was significantly higher (p<0.05) than that of 30, 35 and 50%. The feed conversion ratio of the 40% dietary protein was the significantly lowest at 2.19 +/- 0.163. The dietary protein level of 40% was the most optimum for T. tambroides fingerlings.

Optimum Tilt Angle at Tropical Region

Directory of Open Access Journals (Sweden)

S Soulayman

2015-02-01

Full Text Available : One of the important parameters that affect the performance of a solar collector is its tilt angle with the horizon. This is because of the variation of tilt angle changes the amount of solar radiation reaching the collector surface. Meanwhile, is the rule of thumb, which says that solar collector Equator facing position is the best, is valid for tropical region? Thus, it is required to determine the optimum tilt as for Equator facing and for Pole oriented collectors. In addition, the question that may arise: how many times is reasonable for adjusting collector tilt angle for a definite value of surface azimuth angle? A mathematical model was used for estimating the solar radiation on a tilted surface, and to determine the optimum tilt angle and orientation (surface azimuth angle for the solar collector at any latitude. This model was applied for determining optimum tilt angle and orientation in the tropical zones, on a daily basis, as well as for a specific period. The optimum angle was computed by searching for the values for which the radiation on the collector surface is a maximum for a particular day or a specific period. The results reveal that changing the tilt angle 12 times in a year (i.e. using the monthly optimum tilt angle maintains approximately the total amount of solar radiation near the maximum value that is found by changing the tilt angle daily to its optimum value. This achieves a yearly gain in solar radiation of 11% to 18% more than the case of a solar collector fixed on a horizontal surface.

Investigation on Furan Levels in Pressure-Cooked Foods

Directory of Open Access Journals (Sweden)

Adriana P. Arisseto

2013-01-01

Full Text Available Furan is a food processing contaminant classified as possibly carcinogenic to humans. As the occurrence of furan has been reported in a variety of foods processed in sealed containers, the objective of this work was to investigate if the contaminant can be found in home-cooked foods prepared in a pressure cooker. For that, several foods including beans, soy beans, whole rice, beef, pork, potato, and cassava were pressure-cooked and analyzed for the furan content by gas chromatography coupled to mass spectrometry preceded by a headspace solid phase microextraction (HS-SPME-GC/MS. Furan was not found above the limit of quantification in the pressure-cooked samples. No furan has either been found in reheated samples after 24 hours under cold storage. Although levels up to 173 μg/kg were already reported for commercial canned/jarred foods, it seems that the cooking in a pressure cooker may not represent a concern in relation to the occurrence of furan in foods.

Dialysate magnesium level and blood pressure.

Science.gov (United States)

Kyriazis, John; Kalogeropoulou, Konstantina; Bilirakis, Leonidas; Smirnioudis, Nikolaos; Pikounis, Vasilios; Stamatiadis, Dimitrios; Liolia, Ekaterini

2004-09-01

We investigated the way dialysate magnesium (dMg) concentrations could affect blood pressure (BP) during hemodialysis (HD). Eight HD patients underwent four midweek HD treatments consecutively, using, during each four-hour HD session, one of the following four dialysate formulations, in randomized order, which differed only with regard to dMg and dialysate calcium (dCa) concentrations (in mmol/L): 0.75 dMg, 1.75 dCa (group I); 0.25 dMg, 1.75 dCa (group II); 0.75 dMg, 1.25 dCa (group III); 0.25 dMg, 1.25 dCa (group IV). Before HD and at four 60-minute intervals during the HD sessions, BP and noninvasive measurements of cardiac index (CI) were obtained. Additionally, 14 HD patients were treated for four weeks with 0.5 mmol/L dMg, followed by four weeks with 0.25 mmol/L dMg, and another four weeks with 0.75 mmol/L dMg, in random order. In all treatments dCa was 1.25 mmol/L. BP and symptoms were recorded during each HD session. Mean arterial pressure (MAP) decreased to a significantly (P dMg was superior to the other two treatments regarding intradialytic morbidity (P dMg level to 0.75 mmol/L could prevent IDH frequently seen with the use of 1.25 mmol/L dCa. Thus, manipulating dMg levels independently or in concert with dCa levels might have important implications with regard to dialysis tolerance.

Serum leptin levels correlation with high blood pressure in adult females

International Nuclear Information System (INIS)

Haque, Z.; Shahid, K.U.; Mazahir, I.; Lakho, G.R.; Nafees, M.

2006-01-01

To measure serum leptin levels and compare them in lean and obese subjects and to identify correlation between serum leptin levels, heart rate and hypertension in lean and obese subjects among adult females. Seventy female subjects with different body mass indices were selected from OPD of Jinnah Medical and Dental College Hospital (OPD), Karachi. Heart rate was counted manually; blood pressure was measured by mercury sphygmomanometer while serum leptin was measured using enzyme-linked immunoassay. The outcomes hypertension and heart rate were correlated to risk factor leptin. Mean heart rate, systolic and diastolic blood pressure and serum leptin levels of obese people were 90+-1, 142+-2, 89+-1 and 24.13+-1.7 respectively, which were significantly higher as compared to lean subjects (p<0.05). All the parameters correlated positively and significantly with increasing BMI. There was a relationship of tachycardia and hypertension with high serum leptin levels in obesity. Serum leptin levels increase with the level of obesity. Hyper-leptinemia is associated with tachycardia and increases in both systolic and diastolic blood pressure in obesity via complex mechanisms. (author)

Optimum concrete compression strength using bio-enzyme

OpenAIRE

Bagio Tony Hartono; Basoeki Makno; Tistogondo Julistyana; Pradana Sofyan Ali

2017-01-01

To make concrete with high compressive strength and has a certain concrete specifications other than the main concrete materials are also needed concrete mix quality control and other added material is also in line with the current technology of concrete mix that produces concrete with specific characteristics. Addition of bio enzyme on five concrete mixture that will be compared with normal concrete in order to know the optimum level bio-enzyme in concrete to increase the strength of the con...

Association between individual-level and community-level socio-economic status and blood pressure among Inuit in Greenland

Directory of Open Access Journals (Sweden)

Mylène Riva

2016-12-01

Full Text Available Background: Despite abundant evidence that socio-economic status (SES is a fundamental determinant of health, there is a dearth of research examining association between SES, measured at the individual and community levels, and cardiovascular risk factors and morbidity among indigenous populations. Objectives: To examine the influence of individual-level and community-level SES on systolic and diastolic blood pressure among Greenlandic Inuit. Methods: Multilevel analysis of cross-sectional data from the Inuit Health in Transition – Greenland Survey, to which 3,108 Greenlandic Inuit aged 18 years and older participated. Blood pressure is measured using an automatic device, according to standardized protocol. Individual SES is measured by education. Community socio-economic conditions are measured using combined information on average disposable household income and settlement type. Results: Education was not significantly associated with blood pressure. There was an inverse U-shape association between community socio-economic conditions and blood pressure with significantly lower SBP and DBP among participants living in remote traditional villages characterized by lower average disposable household income and in affluent more urbanized towns. Sex-stratified analyses demonstrate the salience of community conditions for men. Conclusions: The association observed between blood pressure and community-level socio-economic conditions suggests that public health and social policies, programmes and interventions aiming to improve living conditions might improve cardiovascular health in Greenland. Studies are required to further examine social gradients in cardiovascular risk factors and morbidity among indigenous populations using different measures of SES.

Association between individual-level and community-level socio-economic status and blood pressure among Inuit in Greenland.

Science.gov (United States)

Riva, Mylène; Larsen, Christina Viskum Lytken; Bjerregaard, Peter

2016-01-01

Despite abundant evidence that socio-economic status (SES) is a fundamental determinant of health, there is a dearth of research examining association between SES, measured at the individual and community levels, and cardiovascular risk factors and morbidity among indigenous populations. To examine the influence of individual-level and community-level SES on systolic and diastolic blood pressure among Greenlandic Inuit. Multilevel analysis of cross-sectional data from the Inuit Health in Transition - Greenland Survey, to which 3,108 Greenlandic Inuit aged 18 years and older participated. Blood pressure is measured using an automatic device, according to standardized protocol. Individual SES is measured by education. Community socio-economic conditions are measured using combined information on average disposable household income and settlement type. Education was not significantly associated with blood pressure. There was an inverse U-shape association between community socio-economic conditions and blood pressure with significantly lower SBP and DBP among participants living in remote traditional villages characterized by lower average disposable household income and in affluent more urbanized towns. Sex-stratified analyses demonstrate the salience of community conditions for men. The association observed between blood pressure and community-level socio-economic conditions suggests that public health and social policies, programmes and interventions aiming to improve living conditions might improve cardiovascular health in Greenland. Studies are required to further examine social gradients in cardiovascular risk factors and morbidity among indigenous populations using different measures of SES.

Levels of Assertiveness and Peer Pressure of Nursing Students

OpenAIRE

Esin Arslan; Nazan Kiliç Akça; Mürüvvet Baser

2013-01-01

Background: The research was conducted in order to determine levels of assertiveness and peer pressure of the nursing students.Methodology: This descriptive research has been performed with 154 nursing students in Bozok University, The data were collected with Questionnaire Form, Rathus Assertiveness Inventory and Peer Pressure Scale. We used the data one way Anova, two samples t test, the relationship between several independent variables and scales were evaluated by Pearson correlation tech...

A Loudness Function for Maintaining Spectral Balance at Changing Sound Pressure Levels

DEFF Research Database (Denmark)

Nielsen, Sofus Birkedal

Our perception of loudness is a function of frequency as well as sound pressure level as described in ISO226:2003: Normal Equal Loudness Level Contours, which describes the needed sound pressure level for pure tones to be perceived equally loud. At a music performance, this is taking care...... of by the sound engineer by listening to the individual sound sources and adjust and equalize them to the wanted spectral balance including the whole chain of audio equipment and surroundings. At a live venue the sound pressure level will normally change during a concert, and typically increase over time......B is doubling of the effect to the loudspeakers). A level depending digital loudness function has been made based on ISO226:2003, and will be demonstrated. It can maintain the spectral balance at alternating levels and is based on fractional order digital filters. Tutorial. Abstract T3.3 (30th August 16:00 - 17...

How male sound pressure level influences phonotaxis in virgin female Jamaican field crickets (Gryllus assimilis

Directory of Open Access Journals (Sweden)

Karen Pacheco

2014-06-01

Full Text Available Understanding female mate preference is important for determining the strength and direction of sexual trait evolution. The sound pressure level (SPL acoustic signalers use is often an important predictor of mating success because higher sound pressure levels are detectable at greater distances. If females are more attracted to signals produced at higher sound pressure levels, then the potential fitness impacts of signalling at higher sound pressure levels should be elevated beyond what would be expected from detection distance alone. Here we manipulated the sound pressure level of cricket mate attraction signals to determine how female phonotaxis was influenced. We examined female phonotaxis using two common experimental methods: spherical treadmills and open arenas. Both methods showed similar results, with females exhibiting greatest phonotaxis towards loud sound pressure levels relative to the standard signal (69 vs. 60 dB SPL but showing reduced phonotaxis towards very loud sound pressure level signals relative to the standard (77 vs. 60 dB SPL. Reduced female phonotaxis towards supernormal stimuli may signify an acoustic startle response, an absence of other required sensory cues, or perceived increases in predation risk.

Studies on optimum harvest time for hybrid rice seed.

Science.gov (United States)

Fu, Hong; Cao, Dong-Dong; Hu, Wei-Min; Guan, Ya-Jing; Fu, Yu-Ying; Fang, Yong-Feng; Hu, Jin

2017-03-01

Timely harvest is critical for hybrid rice to achieve maximum seed viability, vigor and yield. However, how to predict the optimum harvest time has been rarely reported so far. The seed vigor of Zhuliangyou 06 (ZLY06) increased and reached the highest level at 20 days after pollination (DAP), when seed moisture content had a lower value, which was maintained until final seed maturation. For Chunyou 84 (CY84), seed vigor, fresh and dry weight had relatively high values at 25 DAP, when seed moisture content reached the lowest value and changed slightly from 25 to 55 DAP. In both hybrid rice varieties, seed glume chlorophyll content declined rapidly from 10 to 30 DAP and remained at a very low level after 35 DAP. Starch content exhibited an increasing trend during seed maturation, while both soluble sugar content and amylase activity decreased significantly at the early stages of seed development. Moreover, correlation analyses showed that seed dry weight, starch content and superoxide dismutase activity were significantly positively correlated with seed vigor. In contrast, chlorophyll content, moisture content, soluble sugar, soluble protein, abscisic acid, gibberellin content, electrical conductivity, catalase and ascorbate peroxidase activities were significantly negatively correlated with seed vigor. Physiological and biochemical parameters were obviously more closely related with seed vigor than with seed germinability during seed development. Seed vigor could be better used as a comprehensive factor to predict the optimum seed harvest time. It is suggested that for ZLY06 seeds could be harvested as early as 20 DAP, whereas for CY84 the earliest optimum harvest time was 25 DAP. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Optimum gain and phase for stochastic cooling systems

International Nuclear Information System (INIS)

Meer, S. van der.

1984-01-01

A detailed analysis of optimum gain and phase adjustment in stochastic cooling systems reveals that the result is strongly influenced by the beam feedback effect and that for optimum performance the system phase should change appreciably across each Schottky band. It is shown that the performance is not greatly diminished if a constant phase is adopted instead. On the other hand, the effect of mixing between pick-up and kicker (which produces a phase change similar to the optimum one) is shown to be less perturbing than is usually assumed, provided that the absolute value of the gain is not too far from the optimum value. (orig.)

Optimum bolus wizard settings in insulin pumps in children with Type 1 diabetes

DEFF Research Database (Denmark)

Andersen, A J B; Ostenfeld, A; Pipper, C B

2016-01-01

: Optimum insulin pump settings at pump initiation depend on both insulin requirements and use of the pump. Settings need to be individualized because the standardized calculation factors are not constant for children. There is a need to develop specific age- and insulin dose-dependent calculation factors.......AIM: To evaluate current insulin pump settings in an optimally regulated paediatric population using bolus wizard. METHODS: We used a retrospective study design to analyse data from 124 children on insulin pump therapy who had optimum HbA1c levels [

Thermal Comfort and Optimum Humidity Part 1

Directory of Open Access Journals (Sweden)

M. V. Jokl

2002-01-01

Full Text Available The hydrothermal microclimate is the main component in indoor comfort. The optimum hydrothermal level can be ensured by suitable changes in the sources of heat and water vapor within the building, changes in the environment (the interior of the building and in the people exposed to the conditions inside the building. A change in the heat source and the source of water vapor involves improving the heat - insulating properties and the air permeability of the peripheral walls and especially of the windows. The change in the environment will bring human bodies into balance with the environment. This can be expressed in terms of an optimum or at least an acceptable globe temperature, an adequate proportion of radiant heat within the total amount of heat from the environment (defined by the difference between air and wall temperature, uniform cooling of the human body by the environment, defined a by the acceptable temperature difference between head and ankles, b by acceptable temperature variations during a shift (location unchanged, or during movement from one location to another without a change of clothing. Finally, a moisture balance between man and the environment is necessary (defined by acceptable relative air humidity. A change for human beings means a change of clothes which, of course, is limited by social acceptance in summer and by inconvenient heaviness in winter. The principles of optimum heating and cooling, humidification and dehumidification are presented in this paper.Hydrothermal comfort in an environment depends on heat and humidity flows (heat and water vapors, occurring in a given space in a building interior and affecting the total state of the human organism.

Thermal Comfort and Optimum Humidity Part 2

Directory of Open Access Journals (Sweden)

M. V. Jokl

2002-01-01

Full Text Available The hydrothermal microclimate is the main component in indoor comfort. The optimum hydrothermal level can be ensured by suitable changes in the sources of heat and water vapor within the building, changes in the environment (the interior of the building and in the people exposed to the conditions inside the building. A change in the heat source and the source of water vapor involves improving the heat - insulating properties and the air permeability of the peripheral walls and especially of the windows. The change in the environment will bring human bodies into balance with the environment. This can be expressed in terms of an optimum or at least an acceptable globe temperature, an adequate proportion of radiant heat within the total amount of heat from the environment (defined by the difference between air and wall temperature, uniform cooling of the human body by the environment, defined a by the acceptable temperature difference between head and ankles, b by acceptable temperature variations during a shift (location unchanged, or during movement from one location to another without a change of clothing. Finally, a moisture balance between man and the environment is necessary (defined by acceptable relative air humidity. A change for human beings means a change of clothes which, of course, is limited by social acceptance in summer and by inconvenient heaviness in winter. The principles of optimum heating and cooling, humidification and dehumidification are presented in this paper.Hydrothermal comfort in an environment depends on heat and humidity flows (heat and water vapors, occurring in a given space in a building interior and affecting the total state of the human organism.

Climate Prediction Center Indonesia Sea Level Pressure (1949-present)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This is one of the CPC?s Monthly Atmospheric and SST Indices. It contains standardized sea level pressure anomalies over the equatorial Indonesia region...

A methodology for selecting optimum organizations for space communities

Science.gov (United States)

Ragusa, J. M.

1978-01-01

This paper suggests that a methodology exists for selecting optimum organizations for future space communities of various sizes and purposes. Results of an exploratory study to identify an optimum hypothetical organizational structure for a large earth-orbiting multidisciplinary research and applications (R&A) Space Base manned by a mixed crew of technologists are presented. Since such a facility does not presently exist, in situ empirical testing was not possible. Study activity was, therefore, concerned with the identification of a desired organizational structural model rather than the empirical testing of it. The principal finding of this research was that a four-level project type 'total matrix' model will optimize the effectiveness of Space Base technologists. An overall conclusion which can be reached from the research is that application of this methodology, or portions of it, may provide planning insights for the formal organizations which will be needed during the Space Industrialization Age.

Application of customer-interruption costs for optimum distribution planning

International Nuclear Information System (INIS)

Mok, Y.L.; Chung, T.S.

1996-01-01

We present a new methodology for obtaining optimum values of the integrated cost of utility investment with customer interruption in distribution planning for electric power systems by determining the reliability cost and worth of the distribution system. Reliability cost refers to investment cost of the utility in achieving a defined level of reliability. Reliability worth is the benefit gained by the utility customer from an increase of reliability. A computer program has been developed to determine comparative reliability indices for a typical distribution network. With the average interruption cost, outage duration, average disconnected load, cost data for distribution equipment, etc. being known, the relation between reliability cost, reliability worth and reliability at the specified load point are obtained. The optimum reliability of the distribution system is then determined from the minimum cost to the utility with customer interruption. The applicability of this approach is demonstrated by several practical networks. (Author)

Analysis of the Optimum Gain of a High-Pass L-Matching Network for Rectennas.

Science.gov (United States)

Gasulla, Manel; Jordana, Josep; Robert, Francesc-Josep; Berenguer, Jordi

2017-07-25

Rectennas, which mainly consist of an antenna, matching network, and rectifier, are used to harvest radiofrequency energy in order to power tiny sensor nodes, e.g., the nodes of the Internet of Things. This paper demonstrates for the first time, the existence of an optimum voltage gain for high-pass L-matching networks used in rectennas by deriving an analytical expression. The optimum gain is that which leads to maximum power efficiency of the rectenna. Here, apart from the L-matching network, a Schottky single-diode rectifier was used for the rectenna, which was optimized at 868 MHz for a power range from -30 dBm to -10 dBm. As the theoretical expression depends on parameters not very well-known a priori, an accurate search of the optimum gain for each power level was performed via simulations. Experimental results show remarkable power efficiencies ranging from 16% at -30 dBm to 55% at -10 dBm, which are for almost all the tested power levels the highest published in the literature for similar designs.

Analysis of the Optimum Gain of a High-Pass L-Matching Network for Rectennas

Directory of Open Access Journals (Sweden)

Manel Gasulla

2017-07-01

Full Text Available Rectennas, which mainly consist of an antenna, matching network, and rectifier, are used to harvest radiofrequency energy in order to power tiny sensor nodes, e.g., the nodes of the Internet of Things. This paper demonstrates for the first time, the existence of an optimum voltage gain for high-pass L-matching networks used in rectennas by deriving an analytical expression. The optimum gain is that which leads to maximum power efficiency of the rectenna. Here, apart from the L-matching network, a Schottky single-diode rectifier was used for the rectenna, which was optimized at 868 MHz for a power range from −30 dBm to −10 dBm. As the theoretical expression depends on parameters not very well-known a priori, an accurate search of the optimum gain for each power level was performed via simulations. Experimental results show remarkable power efficiencies ranging from 16% at −30 dBm to 55% at −10 dBm, which are for almost all the tested power levels the highest published in the literature for similar designs.

Optimum Stratification of a Skewed Population

OpenAIRE

D.K. Rao; M.G.M. Khan; K.G. Reddy

2014-01-01

The focus of this paper is to develop a technique of solving a combined problem of determining Optimum Strata Boundaries(OSB) and Optimum Sample Size (OSS) of each stratum, when the population understudy isskewed and the study variable has a Pareto frequency distribution. The problem of determining the OSB isformulated as a Mathematical Programming Problem (MPP) which is then solved by dynamic programming technique. A numerical example is presented to illustrate the compu...

Recovery of Steroidal Alkaloids from Potato Peels Using Pressurized Liquid Extraction

Directory of Open Access Journals (Sweden)

Mohammad B. Hossain

2015-05-01

Full Text Available A higher yield of glycoalkaloids was recovered from potato peels using pressurized liquid extraction (1.92 mg/g dried potato peels compared to conventional solid–liquid extraction (0.981 mg/g dried potato peels. Response surface methodology deduced the optimal temperature and extracting solvent (methanol for the pressurized liquid extraction (PLE of glycoalkaloids as 80 °C in 89% methanol. Using these two optimum PLE conditions, levels of individual steroidal alkaloids obtained were of 597, 873, 374 and 75 µg/g dried potato peel for α-solanine, α-chaconine, solanidine and demissidine respectively. Corresponding values for solid liquid extraction were 59%, 46%, 40% and 52% lower for α-solanine, α-chaconine, solanidine and demissidine respectively.

Swelling pressures of a potential buffer material for high-level waste repository

International Nuclear Information System (INIS)

Lee, Jae Owan; Cho, Won Jin; Chun, Kwan Sik

1999-01-01

The swelling pressure of a potential buffer material was measured and the effect of dry density, bentonite content and initial water content on the swelling pressure was investigated to provide the information for the selection of buffer material in a high-level waste repository. Swelling tests were carried out according to Box-Behnken's experimental design. Measured swelling pressures were in the wide range of 0.7 Kg/cm 2 to 190.2 Kg/cm 2 under given experimental conditions. Based upon the experimental data, a 3-factor polynomial swelling model was suggested to analyze the effect of dry density, bentonite content and initial water content on the swelling pressure. The swelling pressure increased with an increase in the dry density and bentonite content, while it decreased with increasing the initial water content and, beyond about 12 wt.% of the initial water content, levelled to nearly constant value. (author). 21 refs., 10 figs., 4 tabs

Extubation success in premature infants with respiratory distress syndrome treated with bi-level nasal continuous positive airway pressure versus nasal intermittent positive pressure ventilation.

Science.gov (United States)

Thomas, Patricia E; LeFlore, Judy

2013-01-01

Infants born prematurely with respiratory distress syndrome are at high risk for complications from mechanical ventilation. Strategies are needed to minimize their days on the ventilator. The purpose of this study was to compare extubation success rates in infants treated with 2 different types of continuous positive airway pressure devices. A retrospective cohort study design was used. Data were retrieved from electronic medical records for patients in a large, metropolitan, level III neonatal intensive care unit. A sample of 194 premature infants with respiratory distress syndrome was selected, 124 of whom were treated with nasal intermittent positive pressure ventilation and 70 with bi-level variable flow nasal continuous positive airway pressure (bi-level nasal continuous positive airway pressure). Infants in both groups had high extubation success rates (79% of nasal intermittent positive pressure ventilation group and 77% of bi-level nasal continuous positive airway pressure group). Although infants in the bi-level nasal continuous positive airway pressure group were extubated sooner, there was no difference in duration of oxygen therapy between the 2 groups. Promoting early extubation and extubation success is a vital strategy to reduce complications of mechanical ventilation that adversely affect premature infants with respiratory distress syndrome.

MP3 player listening sound pressure levels among 10 to 17 year old students.

Science.gov (United States)

Keith, Stephen E; Michaud, David S; Feder, Katya; Haider, Ifaz; Marro, Leonora; Thompson, Emma; Marcoux, Andre M

2011-11-01

Using a manikin, equivalent free-field sound pressure level measurements were made from the portable digital audio players of 219 subjects, aged 10 to 17 years (93 males) at their typical and "worst-case" volume levels. Measurements were made in different classrooms with background sound pressure levels between 40 and 52 dBA. After correction for the transfer function of the ear, the median equivalent free field sound pressure levels and interquartile ranges (IQR) at typical and worst-case volume settings were 68 dBA (IQR = 15) and 76 dBA (IQR = 19), respectively. Self-reported mean daily use ranged from 0.014 to 12 h. When typical sound pressure levels were considered in combination with the average daily duration of use, the median noise exposure level, Lex, was 56 dBA (IQR = 18) and 3.2% of subjects were estimated to exceed the most protective occupational noise exposure level limit in Canada, i.e., 85 dBA Lex. Under worst-case listening conditions, 77.6% of the sample was estimated to listen to their device at combinations of sound pressure levels and average daily durations for which there is no known risk of permanent noise-induced hearing loss, i.e., ≤  75 dBA Lex. Sources and magnitudes of measurement uncertainties are also discussed.

The Optimum Level of Argumentativeness for Employed Women.

Science.gov (United States)

Schullery, Nancy M.

1998-01-01

Examines the relationship between argumentativeness and women's supervisory level in organizations. Finds no simple relationship between supervisory level and argumentativeness for women, but indicates that moderation in argumentativeness increases with supervisory level. Notes implications for pedagogy: would-be female executives should be…

Flextube reflectometry and pressure recordings for level diagnosis in obstructive sleep apnoea

DEFF Research Database (Denmark)

Faber, C E; Grymer, L; Hilberg, O

2002-01-01

The objective of this study was to compare sound reflections in a flexible tube (flextube reflectometry) with pressure-catheter recordings (ApneaGraph) for identifying the predominant obstructive level of the upper airway during sleep. Seventeen males with suspected obstructive sleep apnoea...... results were found in flextube reflectometry studies and pressure-recordings performed on different nights regarding the level distribution of obstructions during sleep. Possible explanations of this discrepancy are discussed....

Can Population-Level Laterality Stem from Social Pressures? Evidence from Cheek Kissing in Humans.

Science.gov (United States)

Chapelain, Amandine; Pimbert, Pauline; Aube, Lydiane; Perrocheau, Océane; Debunne, Gilles; Bellido, Alain; Blois-Heulin, Catherine

2015-01-01

Despite extensive research, the origins and functions of behavioural laterality remain largely unclear. One of the most striking unresolved issues is the fact that laterality generally occurs at the population-level. Why would the majority of the individuals of a population exhibit the same laterality, while individual-level laterality would yet provide the advantages in terms of improving behavioural efficiency? Are social pressures the key factor? Can social pressures induce alignment of laterality between the individuals of a population? Can the effect of social pressures overpass the effect of other possible determining factors (e.g. genes)? We tested this important new hypothesis in humans, for the first time. We asked whether population-level laterality could stem from social pressures. Namely, we assessed social pressures on laterality in an interactive social behaviour: kissing on the cheek as a greeting. We performed observations in 10 cities of France. The observations took place in spots where people of the city meet and greet each other. We showed that: a) there is a population-level laterality for cheek kissing, with the majority of individuals being aligned in each city, and b) there is a variation between populations, with a laterality that depends on the city. These results were confirmed by our complementary data from questionnaires and internet surveys. These findings show that social pressures are involved in determining laterality. They demonstrate that population-level laterality can stem from social pressures.

Can Population-Level Laterality Stem from Social Pressures? Evidence from Cheek Kissing in Humans.

Directory of Open Access Journals (Sweden)

Amandine Chapelain

Full Text Available Despite extensive research, the origins and functions of behavioural laterality remain largely unclear. One of the most striking unresolved issues is the fact that laterality generally occurs at the population-level. Why would the majority of the individuals of a population exhibit the same laterality, while individual-level laterality would yet provide the advantages in terms of improving behavioural efficiency? Are social pressures the key factor? Can social pressures induce alignment of laterality between the individuals of a population? Can the effect of social pressures overpass the effect of other possible determining factors (e.g. genes? We tested this important new hypothesis in humans, for the first time. We asked whether population-level laterality could stem from social pressures. Namely, we assessed social pressures on laterality in an interactive social behaviour: kissing on the cheek as a greeting. We performed observations in 10 cities of France. The observations took place in spots where people of the city meet and greet each other. We showed that: a there is a population-level laterality for cheek kissing, with the majority of individuals being aligned in each city, and b there is a variation between populations, with a laterality that depends on the city. These results were confirmed by our complementary data from questionnaires and internet surveys. These findings show that social pressures are involved in determining laterality. They demonstrate that population-level laterality can stem from social pressures.

The study and improvement of water level control of pressurizer

International Nuclear Information System (INIS)

Gao Peng; Zhang Qinshun

2006-01-01

The PI controller which is used widely in water level control of pressurizer in reactor control system usually leads dynamic overshoot and long setting time. The improvement project for intelligent fuzzy controller to take the place of PI controller is advanced. This paper researches the water level control of pressurizer in reactor control system of Daya Bay Phase I, and describes the method of intelligent fuzzy control in practice. Simulation indicates that the fuzzy control has advantages of small overshoot and short settling time. It can also improve control system's real time property and anti-interference ability. Especially for non-linear and time-varying complicated control systems, it can obtain good control results. (authors)

High resolution or optimum resolution? Spatial analysis of the Federmesser site at Andernach, Germany

NARCIS (Netherlands)

Stapert, D; Street, M

1997-01-01

This paper discusses spatial analysis at site level. It is suggested that spatial analysis has to proceed in several levels, from global to more detailed questions, and that optimum resolution should be established when applying any quantitative methods in this field. As an example, the ring and

Finding the Optimum Scenario in Risk-benefit Assessment: An Example on Vitamin D

DEFF Research Database (Denmark)

Berjia, Firew Lemma; Hoekstra, J.; Verhagen, H.

2014-01-01

when changing from the reference to the optimum scenario. Conclusion: The method allowed us to find the optimum serum level in the vitamin D example. Additional case studies are needed to further validate the applicability of the approach to other nutrients or foods, especially with regards...... a method for finding the optimum scenario that provides maximum net health gains. Methods: A multiple scenario simulation. The method is presented using vitamin D intake in Denmark as an example. In addition to the reference scenario, several alternative scenarios are simulated to detect the scenario...... that provides maximum net health gains. As a common health metric, Disability Adjusted Life Years (DALY) has been used to project the net health effect by using the QALIBRA (Quality of Life for Benefit Risk Assessment) software. Results: The method used in the vitamin D example shows that it is feasible to find...

Determining the optimum length of a bridge opening with a specified reliability level of water runoff

Directory of Open Access Journals (Sweden)

Evdokimov Sergey

2017-01-01

Full Text Available Current trends in construction are aimed at providing reliability and safety of engineering facilities. According to the latest government regulations for construction, the scientific approach to engineering research, design, construction and operation of construction projects is a key priority. The reliability of a road depends on a great number of factors and characteristics of their statistical compounds (sequential and parallel. A part of a road with such man-made structures as a bridge or a pipe is considered as a system with a sequential element connection. The overall reliability is the multiplication of the reliability of these elements. The parameters of engineering structures defined by analytical dependences are highly volatile because of the inaccuracy of the defining factors. However each physical parameter is statistically unstable that is evaluated by variable coefficient of their values. It causes the fluctuation in the parameters of engineering structures. Their study may result in the changes in general and particular design rules in order to increase the reliability. The paper gives the grounds for these changes by the example of a bridge. It allows calculating its optimum length with a specified reliability level of water runoff under the bridge.

Optimum burnup of BAEC TRIGA research reactor

International Nuclear Information System (INIS)

Lyric, Zoairia Idris; Mahmood, Mohammad Sayem; Motalab, Mohammad Abdul; Khan, Jahirul Haque

2013-01-01

Highlights: ► Optimum loading scheme for BAEC TRIGA core is out-to-in loading with 10 fuels/cycle starting with 5 for the first reload. ► The discharge burnup ranges from 17% to 24% of U235 per fuel element for full power (3 MW) operation. ► Optimum extension of operating core life is 100 MWD per reload cycle. - Abstract: The TRIGA Mark II research reactor of BAEC (Bangladesh Atomic Energy Commission) has been operating since 1986 without any reshuffling or reloading yet. Optimum fuel burnup strategy has been investigated for the present BAEC TRIGA core, where three out-to-in loading schemes have been inspected in terms of core life extension, burnup economy and safety. In considering different schemes of fuel loading, optimization has been searched by only varying the number of fuels discharged and loaded. A cost function has been defined and evaluated based on the calculated core life and fuel load and discharge. The optimum loading scheme has been identified for the TRIGA core, the outside-to-inside fuel loading with ten fuels for each cycle starting with five fuels for the first reload. The discharge burnup has been found ranging from 17% to 24% of U235 per fuel element and optimum extension of core operating life is 100 MWD for each loading cycle. This study will contribute to the in-core fuel management of TRIGA reactor

Tax Efficiency vs. Tax Equity – Points of View regarding Tax Optimum

Directory of Open Access Journals (Sweden)

Stela Aurelia Toader

2011-10-01

Full Text Available Objectives. Starting from the idea that tax equity requirements, administration costs and the tendency towards tax evasion determine the design of tax systems, it is important to identify a satisfactory efficiency/equity deal in order to build a tax system as close to optimum requirements as possible. Prior Work Previous studies proved that an optimum tax system is that through which it will be collected a level of tax revenues which will satisfy budgetary demands, while losing only a minimum ‘amount’ of welfare. In what degree the Romanian tax system meets these requirements? Approach We envisage analyzing the possibilities of improving Romanian tax system as to come nearest to optimum requirements. Results We can conclude fiscal system can uphold important improvements in what assuring tax equity is concerned, resulting in raising the degree of free conformation in the field of tax payment and, implicitly, the degree of tax efficiency. Implications Knowing to what extent it can be acted upon in the direction of finding that satisfactory efficiency/equity deal may allow oneself to identify the blueprint of a tax system in which the loss of welfare is kept down to minimum. Value For the Romanian institutions empowered to impose taxes, the knowledge of the possibilities of making the tax system more efficient can be important while aiming at reducing the level of evasion phenomenon.

Relationship between Optimum Mini-doses of Glucagon and Insulin Levels when Treating Mild Hypoglycaemia in Patients with Type 1 Diabetes - A Simulation Study

DEFF Research Database (Denmark)

Ranjan, Ajenthen; Wendt, Sabrina Lyngbye; Schmidt, Signe

2017-01-01

-treated type 1 diabetes. In each simulation, one of ten different and individualized subcutaneous insulin boluses was administered to decrease plasma glucose (PG) from 7.0 to ≤3.9 mmol/l. Insulin levels were estimated as ratio of actual to baseline serum insulin concentration (se/ba-insulin), insulin on board...... (IOB) or percentage of IOB to total daily insulin dose (IOB/TDD). Insulin bolus sizes were chosen to provide pre-defined insulin levels when PG reached 3.9 mmol/l, where one of 17 subcutaneous glucagon boluses was administered. Optimum glucagon bolus to treat mild hypoglycaemia at varying insulin...... levels was the lowest dose that in most patients caused PG peak between 5.0 and 10.0 mmol/l and sustained PG ≥ 3.9 mmol/l for 2 hr after the bolus. PG response to glucagon declined with increasing insulin levels. The glucagon dose to optimally treat mild hypoglycaemia depended exponentially on insulin...

Optimum Design of a Coil Spring for Improving the Performance of a Spring -Operated Mechanism

International Nuclear Information System (INIS)

Lee, Dae Woo; Sohn, Jeong Hyun; Yoo, Wan Suk

2016-01-01

In this study, a release test bed is designed to evaluate the dynamic behaviors of a coil spring. From the release tests, the dynamic behaviors of a coil spring are analyzed. A lumped parameter spring model was established for numerical simulation of a spring. The design variables of a coil spring are optimized by using the design of experiments approach. Two-level factorial designs are used for the design optimization, and the primary effects of the design variables are analyzed. Based on the results of the interaction analysis and design sensitivity analysis, the level of the design variables is rearranged. Finally, the mixed-level factorial design is used for the optimum design process. According to the optimum design of the opening spring, the dynamic performance of the spring-operated mechanism increases by 2.90

Studies on the replacement policies in dairy cattle II.Optimum policy and influence of changes in production and prices

NARCIS (Netherlands)

Arendonk, van J.A.M.

1985-01-01

A dynamic programming model was developed to determine the optimum replacement policy of dairy cows. In the model cows were described in terms of lactation number, stage of lactation and the level of milk production during the previous and present lactations. The objective in determining the optimum

Optimum Envelope of a Single-Family House Based on Life Cycle Analysis

Directory of Open Access Journals (Sweden)

Marie-Claude Hamelin

2014-04-01

Full Text Available This paper describes the methodology used for the life cycle cost (LCC and life cycle energy (LCE analyses of the case study house in Quebec, Canada. The TRNSYS energy analysis program is coupled with GenOpt, a general purpose optimization program, for the purpose of this study. The particle swarm optimization (PSO algorithm is used for the search for the optimum solution. Results show that the optimum levels of insulation should be higher than the reference values, even for the case of LCC analysis. The results are for the most part still valid if electricity costs are assumed to increase below the inflation rate for the duration of the study period.

Optimum Parameters for Tuned Mass Damper Using Shuffled Complex Evolution (SCE Algorithm

Directory of Open Access Journals (Sweden)

Hessamoddin Meshkat Razavi

2015-06-01

Full Text Available This study is investigated the optimum parameters for a tuned mass damper (TMD under the seismic excitation. Shuffled complex evolution (SCE is a meta-heuristic optimization method which is used to find the optimum damping and tuning frequency ratio for a TMD. The efficiency of the TMD is evaluated by decreasing the structural displacement dynamic magnification factor (DDMF and acceleration dynamic magnification factor (ADMF for a specific vibration mode of the structure. The optimum TMD parameters and the corresponding optimized DDMF and ADMF are achieved for two control levels (displacement control and acceleration control, different structural damping ratio and mass ratio of the TMD system. The optimum TMD parameters are checked for a 10-storey building under earthquake excitations. The maximum storey displacement and acceleration obtained by SCE method are compared with the results of other existing approaches. The results show that the peak building response decreased with decreases of about 20% for displacement and 30% for acceleration of the top floor. To show the efficiency of the adopted algorithm (SCE, a comparison is also made between SCE and other meta-heuristic optimization methods such as genetic algorithm (GA, particle swarm optimization (PSO method and harmony search (HS algorithm in terms of success rate and computational processing time. The results show that the proposed algorithm outperforms other meta-heuristic optimization methods.

Improving boiler unit performance using an optimum robust minimum-order observer

Energy Technology Data Exchange (ETDEWEB)

Moradi, Hamed; Bakhtiari-Nejad, Firooz [Energy and Control Centre of Excellence, Department of Mechanical Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of)

2011-03-15

To achieve a good performance of the utility boiler, dynamic variables such as drum pressure, steam temperature and water level of drum must be controlled. In this paper, a linear time invariant (LTI) model of a boiler system is considered in which the input variables are feed-water and fuel mass rates. Due to the inaccessibility of some state variables of boiler system, a minimum-order observer is designed based on Luenberger's model to gain an estimate state x of the true state x. Low cost of design and high accuracy of states estimation are the main advantages of the minimum-order observer; in comparison with previous designed full-order observers. By applying the observer on the closed-loop system, a regulator system is designed. Using an optimal functional code developed in MATLAB environment, desired observer poles are found such that suitable time response specifications of the boiler system are achieved and the gain and phase margin values are adjusted in an acceptable range. However, the real dynamic model may associate with parametric uncertainties. In that case, optimum region of poles of observer-based controller are found such that the robust performance of the boiler system against model uncertainties is guaranteed. (author)

14 CFR 29.979 - Pressure refueling and fueling provisions below fuel level.

Science.gov (United States)

2010-01-01

..., DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Fuel System § 29.979 Pressure refueling and fueling provisions below fuel level. (a) Each fueling connection... from that tank in case of malfunction of the fuel entry valve. (b) For systems intended for pressure...

Optimum filters for narrow-band frequency modulation.

Science.gov (United States)

Shelton, R. D.

1972-01-01

The results of a computer search for the optimum type of bandpass filter for low-index angle-modulated signals are reported. The bandpass filters are discussed in terms of their low-pass prototypes. Only filter functions with constant numerators are considered. The pole locations for the optimum filters of several cases are shown in a table. The results are fairly independent of modulation index and bandwidth.

Experimental study on the performance of the vapor injection refrigeration system with an economizer for intermediate pressures

Science.gov (United States)

Moon, Chang-Uk; Choi, Kwang-Hwan; Yoon, Jung-In; Kim, Young-Bok; Son, Chang-Hyo; Ha, Soo-Jung; Jeon, Min-Ju; An, Sang-Young; Lee, Joon-Hyuk

2018-04-01

In this study, to investigate the performance characteristics of vapor injection refrigeration system with an economizer at an intermediate pressure, the vapor injection refrigeration system was analyzed under various experiment conditions. As a result, the optimum design data of the vapor injection refrigeration system with an economizer were obtained. The findings from this study can be summarized as follows. The mass flow rate through the compressor increases with intermediate pressure. The compression power input showed an increasing trend under all the test conditions. The evaporation capacity increased and then decreased at the intermediate pressure, and as such, it became maximum at the given intermediate pressure. The increased mass flow rate of the by-passed refrigerant enhanced the evaporation capacity at the low medium pressure range, but the increased saturation temperature limited the subcooling degree of the liquid refrigerant after the application of the economizer when the intermediate pressure kept rising, and degenerated the evaporation capacity. The coefficient of performance (COP) increased and then decreased with respect to the intermediate pressures under all the experiment conditions. Nevertheless, there was an optimum intermediate pressure for the maximum COP under each experiment condition. Therefore, the optimum intermediate pressure in this study was found at -99.08 kPa, which is the theoretical standard medium pressure under all the test conditions.

Challenges in standardization of blood pressure measurement at the population level.

Science.gov (United States)

Tolonen, Hanna; Koponen, Päivikki; Naska, Androniki; Männistö, Satu; Broda, Grazyna; Palosaari, Tarja; Kuulasmaa, Kari

2015-04-10

Accurate blood pressure measurements are needed in clinical practice, intervention studies and health examination surveys. Blood pressure measurements are sensitive: their accuracy can be affected by measurement environment, behaviour of the subject, measurement procedures, devices used for the measurement and the observer. To minimize errors in blood pressure measurement, a standardized measurement protocol is needed. The European Health Examination Survey (EHES) Pilot project was conducted in 2009-2012. A pilot health examination survey was conducted in 12 countries using a standardized protocol. The measurement protocols used in each survey, training provided for the measurers, measurement data, and observations during site visits were collected and evaluated to assess the level of standardization. The EHES measurement protocol for blood pressure was followed accurately in all 12 pilot surveys. Most of the surveys succeeded in organizing a quiet and comfortable measurement environment, and staff instructed survey participants appropriately before examination visits. In all surveys, blood pressure was measured three times, from the right arm in a sitting posture. The biggest variation was in the device used for the blood pressure measurement. It is possible to reach a high level of standardization for blood pressure measurements across countries and over time. A detailed, standardized measurement protocol, and adequate training and monitoring during the fieldwork and centrally organized quality assessment of the data are needed. The recent EU regulation banning the sale of mercury sphygmomanometer in European Union Member States has set new challenges for the standardization of measurement devices since the validity of oscillometric measurements is device-specific and performance of aneroid devices depends very much on calibration.

Optimum material gradient composition for the functionally graded ...

African Journals Online (AJOL)

This study investigates the relation between the material gradient properties and the optimum sensing/actuation design of the functionally graded piezoelectric beams. Three-dimensional (3D) finite element analysis has been employed for the prediction of an optimum composition profile in these types of sensors and ...

Conditions of the optimum development of a high-pressure natural gas pipeline system regarding up-to-date gas economy. [Hungary

Energy Technology Data Exchange (ETDEWEB)

Csako, D.; Torok, A.; Vasvari, V.

1980-03-01

Hungarian engineers enumerate the factors to consider in the planning, construction, and expansion of gas pipeline systems to obtain an optimum solution, both technically and economically. Future development of pipeline systems in Hungary will place equal emphasis on system quality and network expansion.

Atomic processes, cross sections, and reaction rates necessary for modelling hydrogen-negative-ion sources and identification of optimum H- current densities

International Nuclear Information System (INIS)

Hiskes, J.R.

1991-01-01

The principal electron excitation cross sections for vibrational excitation in a hydrogen discharge are reported. In the first chamber of a two-chamber hydrogen negative-ion-source system subject to the beam-line constraint of a maximum gas pressure, the density of vibrationally excited molecules reaches an asymptote for increasing discharge current or the equivalent fast electron density. Operating near this first-chamber asymptote, there exists a spatially-dependent maximum negative-ion density in the second chamber. With the extraction grid placed at this maximum the optimum performance of a hydrogen-based system is determined. This optimum performance provides a criterion for the selection of differing source types for fusion applications

Formation of H- ions via vibrational excited molecules produced from recombinative wall desorption of H atoms in a low-pressure H/sub 2/ positive column

NARCIS (Netherlands)

Amorim, J.; Loureiro, J.; Schram, D.C.

2001-01-01

Recombinative wall desorption of hydrogen atoms in a low-pressure hydrogen positive column leading to formation of H/sub 2/ (X/sup 1/ Sigma /sub g//sup +/, v) molecules in optimum levels for H/sup -/ production by dissociative attachment is investigated. We employed a kinetic model that solves the

The optimum decision rules for the oddity task

NARCIS (Netherlands)

Versfeld, N.J.; Dai, H.; Green, D.M.

1996-01-01

This paper presents the optimum decision rule for an m-interval oddity task in which m-1 intervals contain the same signal and one is different or odd. The optimum decision rule depends on the degree of correlation among observations. The present approach unifies the different strategies that occur

Optimum unambiguous discrimination of linearly independent pure state

DEFF Research Database (Denmark)

Pang, Shengshi; Wu, Shengjun

2009-01-01

be satisfied by the optimum solution in different situations. We also provide the detailed steps to find the optimum measurement strategy. The method and results we obtain are given a geometrical illustration with a numerical example. Furthermore, using these equations, we derive a formula which shows a clear...

On Optimum Stratification

OpenAIRE

M. G. M. Khan; V. D. Prasad; D. K. Rao

2014-01-01

In this manuscript, we discuss the problem of determining the optimum stratification of a study (or main) variable based on the auxiliary variable that follows a uniform distribution. If the stratification of survey variable is made using the auxiliary variable it may lead to substantial gains in precision of the estimates. This problem is formulated as a Nonlinear Programming Problem (NLPP), which turn out to multistage decision problem and is solved using dynamic programming technique.

Association between individual-level and community-level socio-economic status and blood pressure among Inuit in Greenland

DEFF Research Database (Denmark)

Riva, Mylène; Larsen, C. V. L.; Bjerregaard, Peter

2016-01-01

and older participated. Blood pressure is measured using an automatic device, according to standardized protocol. Individual SES is measured by education. Community socio-economic conditions are measured using combined information on average disposable household income and settlement type. Results....... Education was not significantly associated with blood pressure. There was an inverse U-shape association between community socio-economic conditions and blood pressure with significantly lower SBP and DBP among participants living in remote traditional villages characterized by lower average disposable...... household income and in affluent more urbanized towns. Sex-stratified analyses demonstrate the salience of community conditions for men. Conclusions. The association observed between blood pressure and community-level socio-economic conditions suggests that public health and social policies, programmes...

Integration optimisation of elevated pressure air separation unit with gas turbine in an IGCC power plant

International Nuclear Information System (INIS)

Han, Long; Deng, Guangyi; Li, Zheng; Wang, Qinhui; Ileleji, Klein E.

2017-01-01

Highlights: • IGCC thermodynamic model was setup carefully. • Simulations focus on integration between an elevated pressure ASU with gas turbine. • Different recommended solutions from those of low pressure ASUs are figured out. • Full N 2 injection and 80% air extraction was suggested as the optimum integration. - Abstract: The integration optimisation between an elevated pressure air separation unit (EP-ASU) and gas turbine is beneficial to promote net efficiency of an integrated gasification combined cycle (IGCC) power plant. This study sets up the thermodynamic model for a 400 MW plant specially coupled with an EP-ASU, aiming to examine system performances under different integrations and acquire the optimum solution. Influences of air extraction rate at conditions of without, partial and full N 2 injection, as well as the effects of N 2 injection rate when adopting separate ASU, partial and full integrated ASU were both analysed. Special attention has been paid to performance differences between utilising an EP-ASU and a low pressure unit. Results indicated that integration solution with a separate EP-ASU or without N 2 injection would not be reasonable. Among various recommended solutions for different integration conditions, N 2 injection rate increased with the growth of air extraction rate. The integration with an air extraction rate of 80% and full N 2 injection was suggested as the optimum solution. It is concluded that the optimum integration solution when adopting an EP-ASU is different from that using a low pressure one.

Effects of external pressure on the performance and ageing of single-layer lithium-ion pouch cells

Science.gov (United States)

Mussa, Abdilbari Shifa; Klett, Matilda; Lindbergh, Göran; Lindström, Rakel Wreland

2018-05-01

The effects of external compression on the performance and ageing of NMC(1/3)/Graphite single-layer Li-ion pouch cells are investigated using a spring-loaded fixture. The influence of pressure (0.66, 0.99, 1.32, and 1.98 MPa) on impedance is characterized in fresh cells that are subsequently cycled at the given pressure levels. The aged cells are analyzed for capacity fade and impedance rise at the cell and electrode level. The effect of pressure distribution that may occur in large-format cells or in a battery pack is simulated using parallel connected cells. The results show that the kinetic and mass transport resistance increases with pressure in a fresh cell. An optimum pressure around 1.3 MPa is shown to be beneficial to reduce cyclable-lithium loss during cycling. The minor active mass losses observed in the electrodes are independent of the ageing pressure, whereas ageing pressure affects the charge transfer resistance of both NMC and graphite electrodes and the ohmic resistance of the cell. Pressure distribution induces current distribution but the enhanced current throughput at lower pressures cell does not accelerate its ageing. Conclusions from this work can explain some of the discrepancies in non-uniform ageing reported in the literature and indicate coupling between electrochemistry and mechanics.

Code Description for Generation of Meteorological Height and Pressure Level and Layer Profiles

Science.gov (United States)

2016-06-01

defined by user input height or pressure levels. It can process input profiles from sensing systems such as radiosonde, lidar, or wind profiling radar...routine may be required for different input types and formats. meteorological sounding interpolation , integrated mean layer values, US Army Research...or other radiosonde soundings. There are 2 main versions or “methods” that produce output in height- or pressure-based profiles of interpolated level

Hardware-Based Non-Optimum Factors for Launch Vehicle Structural Design

Science.gov (United States)

Wu, K. Chauncey; Cerro, Jeffrey A.

2010-01-01

During aerospace vehicle conceptual and preliminary design, empirical non-optimum factors are typically applied to predicted structural component weights to account for undefined manufacturing and design details. Non-optimum factors are developed here for 32 aluminum-lithium 2195 orthogrid panels comprising the liquid hydrogen tank barrel of the Space Shuttle External Tank using measured panel weights and manufacturing drawings. Minimum values for skin thickness, axial and circumferential blade stiffener thickness and spacing, and overall panel thickness are used to estimate individual panel weights. Panel non-optimum factors computed using a coarse weights model range from 1.21 to 1.77, and a refined weights model (including weld lands and skin and stiffener transition details) yields non-optimum factors of between 1.02 and 1.54. Acreage panels have an average 1.24 non-optimum factor using the coarse model, and 1.03 with the refined version. The observed consistency of these acreage non-optimum factors suggests that relatively simple models can be used to accurately predict large structural component weights for future launch vehicles.

Wind turbine sound pressure level calculations at dwellings.

Science.gov (United States)

Keith, Stephen E; Feder, Katya; Voicescu, Sonia A; Soukhovtsev, Victor; Denning, Allison; Tsang, Jason; Broner, Norm; Leroux, Tony; Richarz, Werner; van den Berg, Frits

2016-03-01

This paper provides calculations of outdoor sound pressure levels (SPLs) at dwellings for 10 wind turbine models, to support Health Canada's Community Noise and Health Study. Manufacturer supplied and measured wind turbine sound power levels were used to calculate outdoor SPL at 1238 dwellings using ISO [(1996). ISO 9613-2-Acoustics] and a Swedish noise propagation method. Both methods yielded statistically equivalent results. The A- and C-weighted results were highly correlated over the 1238 dwellings (Pearson's linear correlation coefficient r > 0.8). Calculated wind turbine SPLs were compared to ambient SPLs from other sources, estimated using guidance documents from the United States and Alberta, Canada.

Association of serum uric acid level and blood pressure in type 2 diabetes mellitus

Science.gov (United States)

Savira, M.; Rusdiana; Syahputra, M.

2018-03-01

Uric acid is an end product of purine degradation in humans and primarily excreted through urine. In adulthood, concentrations rise steadily over time and vary with height, body weight, blood pressure, renal function, and alcohol intake. Uric acid is known as anti-oxidant, it has a beneficial role in diseases. Elevated serum uric acid associated with anincreased risk of cardiovascular disease. It has been found that elevated levels of uric acid associated with high risks of acomplication of type 2 diabetes mellitus and It has astrong association between elevated uric acid levels and obesity, metabolic syndrome, diabetes mellitus, hypertension, cardiovascular and renal disorders. The aim of the study analyzed the association between serum uric acid level and blood pressure in type 2 diabetes mellitus patients. This research is descriptive analytic research with a cross sectional design included 50 diabetic subjects aged over 40 years old. Subjects picked by consecutive sampling then we examined the weight, height, waist size, blood pressure, fasting blood sugar, and serum uric acid level. Statistical analysis using chi-square found that there was no significant association between serum uric acid level and systole and diastole pressure in type 2 diabetes mellitus patients (p>0.005).

Optimum technoeconomic energy autonomous photovoltaic solution for remote consumers throughout Greece

International Nuclear Information System (INIS)

Kaldellis, J.K.

2004-01-01

Autonomous photovoltaic systems have turned into one of the most promising ways to handle the electrification requirements of numerous isolated consumers worldwide. Such an autonomous system comprises a number of photovoltaic panels, properly connected, and a battery storage device, along with the corresponding electronic equipment. Considering the high solar potential of most Greek territories, an integrated study is conducted based on long term solar potential experimental measurements in order to determine the optimum configuration of a stand alone photovoltaic system at representative locations all over Greece. The proposed solution 'guarantees' zero load rejections for all the areas and time periods examined. For this purpose, a fast and reliable numerical code 'PHOTOV-III' has been used. The algorithm provides analytical results concerning the energy autonomy and the operational status of the autonomous system components. Besides, the optimum panel tilt angle, minimizing the first installation cost of a small photovoltaic system, is predicted. Finally, by introducing available financial aspects, it is possible to determine the optimum system dimensions on a minimum first installation cost basis. According to the results obtained, an autonomous photovoltaic system can definitely contribute to solution of the urgent electrification problem of remote consumers spread throughout Greece, also improving their life quality level

Optimum Control for Nonlinear Dynamic Radial Deformation of Turbine Casing with Time-Varying LSSVM

Directory of Open Access Journals (Sweden)

Cheng-Wei Fei

2015-01-01

Full Text Available With the development of the high performance and high reliability of aeroengine, the blade-tip radial running clearance (BTRRC of high pressure turbine seriously influences the reliability and performance of aeroengine, wherein the radial deformation control of turbine casing has to be concerned in BTRRC design. To improve BTRRC design, the optimum control-based probabilistic optimization of turbine casing radial deformation was implemented using time-varying least square support vector machine (T-LSSVM by considering nonlinear material properties and dynamic thermal load. First the T-LSSVM method was proposed and its mathematical model was established. And then the nonlinear dynamic optimal control model of casing radial deformation was constructed with T-LSSVM. Thirdly, through the numerical experiments, the T-LSSVM method is demonstrated to be a promising approach in reducing additional design samples and improving computational efficiency with acceptable computational precision. Through the optimum control-based probabilistic optimization for nonlinear dynamic radial turbine casing deformation, the optimum radial deformation is 7.865 × 10−4 m with acceptable reliability degree 0.995 6, which is reduced by 7.86 × 10−5 m relative to that before optimization. These results validate the effectiveness and feasibility of the proposed T-LSSVM method, which provides a useful insight into casing radial deformation, BTRRC control, and the development of gas turbine with high performance and high reliability.

Optimum Fermentation Process for Red Macroalgae Gelidium latifolium and Gracillaria verrucosa

Directory of Open Access Journals (Sweden)

Mujizat Kawaroe

2015-12-01

Full Text Available Red macroalgae have the potential to be processed into bioethanol due to their high carbohydrate and low lignin content. Gelidium latifolium and Gracilaria verrucosa are red macroalgae commonly found in Indonesian seas. Sometimes an over-supply of red macroalgae is rejected by the food industry, which opens up opportunities for others uses, e.g. for producing bioethanol. The objectives of this research were to analyze the influence of sulfuric acid concentration on hydrolysis of G. latifolium and G. verrucosa and to calculate the optimum fermentation process to produce bioethanol. G. latifolium and G. verrucosa were hydrolyzed using H2SO4 at concentrations of 1%, 2%, 3%, and 4%, at a temperature of 121 °C and a pressure of 1.5 bar for 45 minutes. The process of fermentation was done using Saccharomyces cerevisiae in anaerobic conditions for 4, 5, 6 and 7 days. The results show that the optimum H2SO4 concentrations to hydrolyze G. latifolium and G. verrucosa were 1% and 2% respectively. The number of S. cerevisiae cells in hydrolysate G. latifolium and G. verrucosa increased in the third adaptation. S. cerevisiae can convert sugar from G. latifolium and G. verrucosa into bioethanol through fermentation. The highest bioethanol yields were achieved on days five and six. Therefore, red macroalgae can be seen as a potential raw material for bioethanol production.

‘Optimum mobility’ facelift. Part 2 – the technique

OpenAIRE

Fanous, Nabil; Karsan, Naznin; Zakhary, Kristina; Tawile, Carolyne

2006-01-01

In the first of this two-part article on the ‘optimum mobility’ facelift, facial tissue mobility was analyzed, and three theories or mechanisms emerged: ‘intrinsic mobility’, ‘surgically induced mobility’ and ‘optimum mobility points’.

Finding optimum airfoil shape to get maximum aerodynamic efficiency for a wind turbine

Science.gov (United States)

Sogukpinar, Haci; Bozkurt, Ismail

2017-02-01

In this study, aerodynamic performances of S-series wind turbine airfoil of S 825 are investigated to find optimum angle of attack. Aerodynamic performances calculations are carried out by utilization of a Computational Fluid Dynamics (CFD) method withstand finite capacity approximation by using Reynolds-Averaged-Navier Stokes (RANS) theorem. The lift and pressure coefficients, lift to drag ratio of airfoil S 825 are analyzed with SST turbulence model then obtained results crosscheck with wind tunnel data to verify the precision of computational Fluid Dynamics (CFD) approximation. The comparison indicates that SST turbulence model used in this study can predict aerodynamics properties of wind blade.

Pressure sound level measurements at an educational environment in Goiania, Goias, Brazil

Energy Technology Data Exchange (ETDEWEB)

Costa, Jhonatha J.L.; Nascimento, Eriberto O. do; Oliveira, Lucas N. de [Instituto Federal de Educação, Ciência e Tecnologia de Goiás (IFG), Goiânia, GO (Brazil); Caldas, Linda V. E., E-mail: lcaldas@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

2017-07-01

In this work, twenty five points located on the ground floor of the Federal Institute of Education, Science and Technology of Goias - IFG - Campus Goiania, were analyzed in morning periods of two Saturdays. The pressure sound levels were measured at internal and external environments during routine activities seeking to perform an environmental monitoring at this institution. The initial hypothesis was that an amusement park (Mutirama Park) was responsible for originating noise pollution in the institution, but the results showed, within the campus environment, sound pressure levels in accordance with the Municipal legislation of Goiania for all points. (author)

Pressure sound level measurements at an educational environment in Goiania, Goias, Brazil

International Nuclear Information System (INIS)

Costa, Jhonatha J.L.; Nascimento, Eriberto O. do; Oliveira, Lucas N. de; Caldas, Linda V. E.

2017-01-01

In this work, twenty five points located on the ground floor of the Federal Institute of Education, Science and Technology of Goias - IFG - Campus Goiania, were analyzed in morning periods of two Saturdays. The pressure sound levels were measured at internal and external environments during routine activities seeking to perform an environmental monitoring at this institution. The initial hypothesis was that an amusement park (Mutirama Park) was responsible for originating noise pollution in the institution, but the results showed, within the campus environment, sound pressure levels in accordance with the Municipal legislation of Goiania for all points. (author)

The determination of the optimum counting conditions for a ZnS(Ag) scintillation detector

International Nuclear Information System (INIS)

Djurasevic, M.M.; Kandic, A.B.; Novkovic, D.N; Vukanac, I.S. . E-mail address of corresponding author: mirad@vin.bg.ac.yu; Djurasevic, M.M.)

2005-01-01

The methods that use scintillation counting with ZnS(Ag) scintillation detector are widely used for gross alpha activity determination. The common criteria for the selection of optimum counting condition for a ZnS(Ag) scintillation detector do not consider simultaneously operating voltage and discrimination level variation. In presented method a relationship between voltage and discrimination level is derived for counting efficiency. (author)

Problem of determining optimum geological and technical measures

Energy Technology Data Exchange (ETDEWEB)

Osipov, G N; Roste, Z A; Salimzhanov, E S

1968-01-01

This article is concerned with the mathematical simulation of oilfield operation, particularly the use of linear programing to determine optimum conditions for exploitation of a field. The basic approach is to define the field operation by a series of equations, apply boundary conditions and through an iterative computer technique find optimum operating conditions. Application of the method to Tuimazy field is illustrated.

Use of inexpensive pressure transducers for measuring water levels in wells

Science.gov (United States)

Keeland, B.D.; Dowd, J.F.; Hardegree, W.S.

1997-01-01

Frequent measurement of below ground water levels at multiple locations is an important component of many wetland ecosystem studies. These measurements, however, are usually time consuming, labor intensive, and expensive. This paper describes a water-level sensor that is inexpensive and easy to construct. The sensor is placed below the expected low water level in a shallow well and, when connected to a datalogger, uses a pressure transducer to detect groundwater or surface water elevations. Details of pressure transducer theory, sensor construction, calibration, and examples of field installations are presented. Although the transducers must be individually calibrated, the sensors have a linear response to changing water levels (r2 ??? .999). Measurement errors resulting from temperature fluctuations are shown to be about 4 cm over a 35??C temperature range, but are minimal when the sensors are installed in groundwater wells where temperatures are less variable. Greater accuracy may be obtained by incorporating water temperature data into the initial calibration (0.14 cm error over a 35??C temperature range). Examples of the utility of these sensors in studies of groundwater/surface water interactions and the effects of water level fluctuations on tree growth are provided. ?? 1997 Kluwer Academic Publishers.

High pressure, low pressure and hot water heating systems in hospitals. Hochdruck-, Niederdruck- und Warmwasserheizungsanlagen im Krankenhaus

Energy Technology Data Exchange (ETDEWEB)

Riedle, K [H. Riedle GmbH, Wiesbaden (Germany)

1994-07-01

In hospital nowadays the limitation of the use of steam boilers and their direct supply network to the possible minimum is aimed at when the heating system is exchanged or retrofitted. Independent of the fact whether high pressure or low pressure steam or hot water is used the optimum water treatment should be carried out with a minimum of chemical substances. Here hydroquinone, neutralizing amines, carbohydrazide, sodium sulphite and tannins can be used. The dimensioning of hot water heating circuits is shown with examples. (BWI)

Associations between cadmium levels in blood and urine, blood pressure and hypertension among Canadian adults

Energy Technology Data Exchange (ETDEWEB)

Garner, Rochelle E., E-mail: rochelle.garner@canada.ca [Health Analysis Division, Statistics Canada, Ottawa, Ontario (Canada); Levallois, Patrick [Direction de la santé environnementale et de la toxicologie, Institut National de Santé Publique du Québec, Québec City, Québec (Canada); Axe santé des populations et pratiques optimales en santé, Centre de Recherche du CHU de Québec-Université Laval, Québec City, Québec (Canada)

2017-05-15

Background: Cadmium has been inconsistently related to blood pressure and hypertension. The present study seeks to clarify the relationship between cadmium levels found in blood and urine, blood pressure and hypertension in a large sample of adults. Methods: The study sample included participants ages 20 through 79 from multiple cycles of the Canadian Health Measures Survey (2007 through 2013) with measured blood cadmium (n=10,099) and urinary cadmium (n=6988). Linear regression models examined the association between natural logarithm transformed cadmium levels and blood pressure (separate models for systolic and diastolic blood pressure) after controlling for known covariates. Logistic regression models were used to examine the association between cadmium and hypertension. Models were run separately by sex, smoking status, and body mass index category. Results: Men had higher mean systolic (114.8 vs. 110.8 mmHg, p<0.01) and diastolic (74.0 vs. 69.6 mmHg, p<0.01) blood pressure compared to women. Although, geometric mean blood (0.46 vs. 0.38 µg/L, p<0.01) and creatinine-adjusted standardized urinary cadmium levels (0.48 vs. 0.38 µg/L, p<0.01) were higher among those with hypertension, these differences were no longer significant after adjustment for age, sex and smoking status. In overall regression models, increases in blood cadmium were associated with increased systolic (0.70 mmHg, 95% confidence interval [CI]=0.25–1.16, p<0.01) and diastolic blood pressure (0.74 mmHg, 95% CI=0.30–1.19, p<0.01). The associations between urinary cadmium, blood pressure and hypertension were not significant in overall models. Model stratification revealed significant and negative associations between urinary cadmium and hypertension among current smokers (OR=0.61, 95% CI=0.44–0.85, p<0.01), particularly female current smokers (OR=0.52, 95% CI=0.32–0.85, p=0.01). Conclusion: This study provides evidence of a significant association between cadmium levels, blood pressure

Associations between cadmium levels in blood and urine, blood pressure and hypertension among Canadian adults

International Nuclear Information System (INIS)

Garner, Rochelle E.; Levallois, Patrick

2017-01-01

Background: Cadmium has been inconsistently related to blood pressure and hypertension. The present study seeks to clarify the relationship between cadmium levels found in blood and urine, blood pressure and hypertension in a large sample of adults. Methods: The study sample included participants ages 20 through 79 from multiple cycles of the Canadian Health Measures Survey (2007 through 2013) with measured blood cadmium (n=10,099) and urinary cadmium (n=6988). Linear regression models examined the association between natural logarithm transformed cadmium levels and blood pressure (separate models for systolic and diastolic blood pressure) after controlling for known covariates. Logistic regression models were used to examine the association between cadmium and hypertension. Models were run separately by sex, smoking status, and body mass index category. Results: Men had higher mean systolic (114.8 vs. 110.8 mmHg, p<0.01) and diastolic (74.0 vs. 69.6 mmHg, p<0.01) blood pressure compared to women. Although, geometric mean blood (0.46 vs. 0.38 µg/L, p<0.01) and creatinine-adjusted standardized urinary cadmium levels (0.48 vs. 0.38 µg/L, p<0.01) were higher among those with hypertension, these differences were no longer significant after adjustment for age, sex and smoking status. In overall regression models, increases in blood cadmium were associated with increased systolic (0.70 mmHg, 95% confidence interval [CI]=0.25–1.16, p<0.01) and diastolic blood pressure (0.74 mmHg, 95% CI=0.30–1.19, p<0.01). The associations between urinary cadmium, blood pressure and hypertension were not significant in overall models. Model stratification revealed significant and negative associations between urinary cadmium and hypertension among current smokers (OR=0.61, 95% CI=0.44–0.85, p<0.01), particularly female current smokers (OR=0.52, 95% CI=0.32–0.85, p=0.01). Conclusion: This study provides evidence of a significant association between cadmium levels, blood pressure

Biomass and leaf-level gas exchange characteristics of three African savanna C4 grass species under optimum growth conditions

NARCIS (Netherlands)

Mantlana, K.B.; Veenendaal, E.M.; Arneth, A.; Grispen, V.; Bonyongo, C.M.; Heitkönig, I.M.A.; Lloyd, J.

2009-01-01

C4 savanna grass species, Digitaria eriantha, Eragrostis lehmanniana and Panicum repens, were grown under optimum growth conditions with the aim of characterizing their above- and below-ground biomass allocation and the response of their gas exchange to changes in light intensity, CO2 concentration

Tailoring electrode/electrolyte interfacial properties in flexible supercapacitors by applying pressure

Energy Technology Data Exchange (ETDEWEB)

Masarapu, Charan; Wang, Lian-Ping; Li, Xin; Wei, Bingqing [Department of Mechanical Engineering, University of Delaware, Newark, DE (United States)

2012-05-15

Electrode/electrolyte interfacial properties of flexible supercapacitors assembled with nanostructured activated carbon fabric (ACF) electrodes can be tailored by applying a pressure and tuning electrolyte ion size relative to electrode pore size. Experimental results reveal that increasing pressure between the supercapacitor electrodes can significantly improve capacitive performance. The ratio of solvated ion size in the electrolyte to the pore size on the electrodes determines the minimum pressure necessary to achieve an optimum performance. For a specific electrode material, this minimum pressure for optimum performance is primarily governed by the size of the larger solvated ions (either the anions or cations), and is lower ({proportional_to}689 KPa) when the ratio of the solvated ion size to the pore size is higher than 0.6, and is higher (at least 1379 KPa) when the ratio is lower than 0.6. An analytical model capable of predicting the experimental performance data has been developed. These results together provide a fundamental understanding of pressure dependence of electrode/electrolyte interfacial properties and pave the way for practical applications of flexible supercapacitors. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Optimum target thickness for polarimeters

International Nuclear Information System (INIS)

Sitnik, I.M.

2003-01-01

Polarimeters with thick targets are a tool to measure the proton polarization. But the question about the optimum target thickness is still the subject of discussion. An attempt to calculate the most common parameters concerning this problem, in a few GeV region, is made

Optimization of Pressurized Oxy-Combustion with Flameless Reactor

Energy Technology Data Exchange (ETDEWEB)

Malavasi, Massimo [Itea SpA, Gallarate, VA (Italy); Landegger, Gregory [ThermoEnergy Corporation, Worcester, MA (United States)

2014-06-30

Pressurized OxyECombustion is one of the most promising technologies for utility-scale power generation plants. Benefits include the ability to burn low rank coal and capture CO₂. By increasing the flue gas pressure during this process, greater efficiencies are derived from increased quantity and quality of thermal energy recovery. UPA with modeling support from MIT and testing and data verification by Georgia Tech’s Research Center designed and built a 100 kW system capable of demonstrating pressurized oxyEcombustion using a flameless combustor. Wyoming PRB coal was run at 15 and 32 bar. Additional tests were not completed but sampled data demonstrated the viability of the technology over a broader range of operating pressures, Modeling results illustrated a flat efficiency curve over 20 bar, with optimum efficiency achieved at 29 bar. This resulted in a 33% (HHV) efficiency, a 5 points increase in efficiency versus atmospheric oxy-combustion, and a competitive cost of electricity plus greater CO₂ avoidance costs then prior study’s presented. UPA’s operation of the bench-scale system provided evidence that key performance targets were achieved: flue gas sampled at the combustor outlet had non-detectable residual fly ashes, and low levels of SO3 and heavy-metal. These results correspond to prior pressurized oxy-combustion testing completed by IteaEEnel.

Experimental and finite element prediction of bursting pressure in compound cylinders

International Nuclear Information System (INIS)

Majzoobi, G.H.; Farrahi, G.H.; Pipelzadeh, M.K.; Akbari, A.

2004-01-01

Aluminium cylinders with a constant ratio of outer to inner radii, k=2.2, with different diametral interferences and various shrinkage radii were subjected to bursting and autofrettage pressures. Numerical simulations of the compound cylinders were also performed using the finite element code, NISA. The results can predict the optimum shrinkage radius to a reasonable accuracy with the use of finite element analysis. This radius corresponds to the situation when the maximum von-Mises stress at the internal radii of both the inner and outer cylinders become equal. It was shown that the maximum von-Mises stress across the wall of the cylinder is at the minimum at this shrinkage radius. The optimum diametral interference was found to be that which sufficiently brought the contact surface of the inner and outer cylinders to the point of yielding. Should the shrinkage pressure exceed the elastic limit, the pressure capacity of the cylinder will not be improved. The numerical and experimental results show that autofrettage had no effect on the bursting pressure of the thick-walled compound cylinder for the material tested

Performance characteristics of aerodynamically optimum turbines for wind energy generators

Science.gov (United States)

Rohrbach, C.; Worobel, R.

1975-01-01

This paper presents a brief discussion of the aerodynamic methodology for wind energy generator turbines, an approach to the design of aerodynamically optimum wind turbines covering a broad range of design parameters, some insight on the effect on performance of nonoptimum blade shapes which may represent lower fabrication costs, the annual wind turbine energy for a family of optimum wind turbines, and areas of needed research. On the basis of the investigation, it is concluded that optimum wind turbines show high performance over a wide range of design velocity ratios; that structural requirements impose constraints on blade geometry; that variable pitch wind turbines provide excellent power regulation and that annual energy output is insensitive to design rpm and solidity of optimum wind turbines.

Optimum strategies for nuclear energy system development (method of synthesis)

International Nuclear Information System (INIS)

Belenky, V.Z.

1983-01-01

The problem of optimum long-term development of the nuclear energy system is considered. The optimum strategies (i.e. minimum total uranium consumption) for the transition phase leading to a stationary regime of development are found. For this purpose the author has elaborated a new method of solving linear problems of optimal control which can include jumps in trajectories. The method gives a possibility to fulfil a total synthesis of optimum strategies. A key characteristic of the problem is the productivity function of the nuclear energy system which connects technological system parameters with its growth rate. There are only two types of optimum strategies, according to an increasing or decreasing productivity function. Both cases are illustrated with numerical examples. (orig.) [de

Dielectric properties, optimum formulation and microwave baking conditions of chickpea cakes.

Science.gov (United States)

Alifakı, Yaşar Özlem; Şakıyan, Özge

2017-03-01

The aim of this study was to correlate dielectric properties with quality parameters, and to optimize cake formulation and baking conditions by response surface methodology. Weight loss, color, specific volume, hardness and porosity were evaluated. The samples with different DATEM (0.4, 0.8 and 1.2%) and chickpea flour concentrations (30, 40 and 50%) were baked in microwave oven at different power (300, 350, 400 W) and baking times (2.50, 3.0, 3.50 min). It was found that microwave power showed significant effect on color, while baking time showed effect on weight loss, porosity, hardness, specific volume and dielectric properties. Emulsifier level affected porosity, specific volume and dielectric constant. Chickpea flour level affected porosity, color, hardness and dielectric properties of cakes. The optimum microwave power, baking time, DATEM level and chickpea flour level were found as 400 W, 2.84 min, 1.2% and 30%, respectively. The comparison between conventionally baked and the microwave baked cakes at optimum points showed that color difference, weight loss, specific volume and porosity values of microwave baked cakes were less than those of conventionally baked cakes, on the other hand, hardness values were higher. Moreover, a negative correlation between dielectric constant and porosity, and weight loss values were detected for microwave baked samples. A negative correlation between dielectric loss factor and porosity was observed. These correlations indicated that quality characteristics of a microwave baked cake sample can be assessed from dielectric properties. These correlations provides understanding on the behavior of food material during microwave processing.

Determination of the Optimum Conditions for Production of Chitosan Nanoparticles

Directory of Open Access Journals (Sweden)

A. Dustgani

2007-12-01

Full Text Available Bioedegradable nanoparticles are intensively investigated for their potential applications in drug delivery systems. Being a biocompatible and biodegradable polymer, chitosan holds great promise for use in this area. This investigation was concerned with determination and optimization of the effective parameters involved in the production of chitosan nanoparticles using ionic gelation method. Studied variables were concentration and pH of the chitosan solution, the ratio of chitosan to sodium tripolyphosphate therein and the molecular weight of chitosan. For this purpose, Taguchistatistical method was used for design of experiments in three levels. The size of chitosan nanoparticle was determined using laser light scattering. The experimental results showed that concentration of chitosan solution was the most important parameter and chitosan molecular weight the least effective parameter. The optimum conditions for preparation of nanoparticles were found to be 1 mg/mL chitosan solution with pH=5, chitosan to sodium tripolyphosphate ratio of 3 and chitosan molecular weight of 200,000 daltons. The average nanoparticle size at optimum conditions was found to be about 150 nm.

Study in determining optimum conditions for reducing NORM in Malaysian zircon mineral

International Nuclear Information System (INIS)

Meor Yusoff Meor Sulaiman

2002-01-01

Malaysian zircon contains higher level of NORM especially uranium and thorium than the permissible level set by many importing countries. These elements are present mainly on the mineral surface as well as in its crystal lattice. A study was conducted using selective leaching to reduce NORM content in the mineral. Various parameters such as temperature, time, concentration of leachants, particle size and heat treatment affect the rate of leaching. Optimum conditions for these parameters were determined in order for maximum reduction will be obtained. (Author)

Parametric Investigation of Optimum Thermal Insulation Thickness for External Walls

Directory of Open Access Journals (Sweden)

Omer Kaynakli

2011-06-01

Full Text Available Numerous studies have estimated the optimum thickness of thermal insulation materials used in building walls for different climate conditions. The economic parameters (inflation rate, discount rate, lifetime and energy costs, the heating/cooling loads of the building, the wall structure and the properties of the insulation material all affect the optimum insulation thickness. This study focused on the investigation of these parameters that affect the optimum thermal insulation thickness for building walls. To determine the optimum thickness and payback period, an economic model based on life-cycle cost analysis was used. As a result, the optimum thermal insulation thickness increased with increasing the heating and cooling energy requirements, the lifetime of the building, the inflation rate, energy costs and thermal conductivity of insulation. However, the thickness decreased with increasing the discount rate, the insulation material cost, the total wall resistance, the coefficient of performance (COP of the cooling system and the solar radiation incident on a wall. In addition, the effects of these parameters on the total life-cycle cost, payback periods and energy savings were also investigated.

Optimum design of steel structures

CERN Document Server

Farkas, József

2013-01-01

This book helps designers and manufacturers to select and develop the most suitable and competitive steel structures, which are safe, fit for production and economic. An optimum design system is used to find the best characteristics of structural models, which guarantee the fulfilment of design and fabrication requirements and minimize the cost function. Realistic numerical models are used as main components of industrial steel structures. Chapter 1 containts some experiences with the optimum design of steel structures Chapter 2 treats some newer mathematical optimization methods. Chapter 3 gives formulae for fabrication times and costs. Chapters 4 deals with beams and columns. Summarizes the Eurocode rules for design. Chapter 5 deals with the design of tubular trusses. Chapter 6 gives the design of frame structures and fire-resistant design rules for a frame. In Chapters 7 some minimum cost design problems of stiffened and cellular plates and shells are worked out for cases of different stiffenings and loads...

The optimum size of rotating qarḍ ḥasan savings and credit associations

Directory of Open Access Journals (Sweden)

Seyed Kazem Sadr

2017-07-01

Full Text Available Purpose - Several indigenous credit and savings schemes have been accredited recently in developing countries for the benefit of households and entrepreneurs alike. Famous among them are the Rotating Savings and Credit Associations (ROSCAs that exist in almost all continents currently. The rapid development of ROSCAs and their varied structures in many countries have been the subject of numerous studies. What has not been thoroughly analysed is the optimum size of these associations and the fact that lending and borrowing is without interest. The aim of this paper is to present a model that would determine the optimum size of ROSCAs and deal with the following issues: how the group size varies with changes in the income level of the members, the demand for the loan, the size of the collected loan and its duration. Further, the question of whether or not lending to the association in return for obtaining larger sums is a violation of the qarḍ (loan contract is dealt with, and several Sharīʿah compatible formulations are provided. Design/methodology/approach - Economic analysis has been applied to show the optimum size of Qarḍ Ḥasan Associations (QHAs, which are the Sharīʿah-compliant equivalent of ROSCAs, and the Sharīʿah rules of the qarḍ contract to illustrate the legitimacy of group lending. Findings - The major findings of this study are determination of the optimum size of QHAs, the factors that affect the size and suggestion of alternative legal forms for group financing. Research limitations/implications - Inaccessibility to sources of data to test the hypothesis that has been put forth is the main difficulty encountered when conducting research on the subject. Practical implications - The paper concludes that the development of informal interest-free ROSCAs in both Muslim and non-Muslim countries is an efficient informal microfinance scheme and that it is compatible with Sharīʿah rules. Originality/value - The optimum size

Adropin levels and target organ damage secondary to high blood pressure in the ED.

Science.gov (United States)

Gulen, Bedia; Eken, Cenker; Kucukdagli, Okkes Taha; Serinken, Mustafa; Kocyigit, Abdurrahim; Kılıc, Elif; Uyarel, Hüseyin

2016-11-01

High blood pressure is still a challenge for emergency physicians to discern the patients that require further analysis to establish the existence of acute hypertensive target organ damage (TOD). The present study aimed to reveal that adropin levels are useful for detecting TOD in patients presenting with high blood pressure. Patients presenting with a blood pressure of more than 180/110 mm Hg were enrolled into the study. After a resting period of 15 minutes, patients' blood pressures were measured thrice at 5-minute intervals while the patients were sitting on a chair, and the average of these measurements was accepted as the baseline value. Blood samples were obtained for either adropin levels or possible TOD during the emergency department admission. A total of 119 patients were included in the study. The mean systolic and diastolic blood pressures of study patients were 204.8±23.2 and 108.3 ± 10.3, respectively, and 42% (n = 50) of the patients had TOD. Although the adropin levels were similar between the patients with or without TOD (TOD group = 195 pg/mL, interquartile range [IQR]: 178-201; no-TOD group = 196 pg/mL, IQR: 176-204 [P = .982]), it is significantly higher in normotensive patients (normotensive group = 289 pg/mL, IQR: 193-403) compared with the hypertensive ones (P high blood pressure to the emergency department. Copyright © 2016 Elsevier Inc. All rights reserved.

Designing from minimum to optimum functionality

Science.gov (United States)

Bannova, Olga; Bell, Larry

2011-04-01

This paper discusses a multifaceted strategy to link NASA Minimal Functionality Habitable Element (MFHE) requirements to a compatible growth plan; leading forward to evolutionary, deployable habitats including outpost development stages. The discussion begins by reviewing fundamental geometric features inherent in small scale, vertical and horizontal, pressurized module configuration options to characterize applicability to meet stringent MFHE constraints. A proposed scenario to incorporate a vertical core MFHE concept into an expanded architecture to provide continuity of structural form and a logical path from "minimum" to "optimum" design of a habitable module. The paper describes how habitation and logistics accommodations could be pre-integrated into a common Hab/Log Module that serves both habitation and logistics functions. This is offered as a means to reduce unnecessary redundant development costs and to avoid EVA-intensive on-site adaptation and retrofitting requirements for augmented crew capacity. An evolutionary version of the hard shell Hab/Log design would have an expandable middle section to afford larger living and working accommodations. In conclusion, the paper illustrates that a number of cargo missions referenced for NASA's 4.0.0 Lunar Campaign Scenario could be eliminated altogether to expedite progress and reduce budgets. The plan concludes with a vertical growth geometry that provides versatile and efficient site development opportunities using a combination of hard Hab/Log modules and a hybrid expandable "CLAM" (Crew Lunar Accommodations Module) element.

Evaluation of pressure transducers to measure surface level in the waste storage tanks

International Nuclear Information System (INIS)

Peters, T.J.; Colson, J.B.

1994-06-01

This report describes the results of tests conducted at the Pacific Northwest Laboratory (PNL) to determine if pressure transducers can be used to measure the surface level in the waste tanks. A survey was first conducted to evaluate which, if any, commercially available pressure transducers were available that could meet the requirements for use in the waste tanks. More than 35 companies were contacted to determine if they manufactured a pressure transducer that could be used in the 101-SY waste tank. The three basic requirements for a pressure transducer for this application were that they were radiation-hardened, could withstand a caustic environment, and were certified to be intrinsically safe. No manufacturer was able to meet all three of these requirements with a commercially available product. Seven companies were able to meet the requirements for being radiation-hardened and being able to withstand the caustic environment. However, only two of the nine companies were willing to supply a pressure transducer for laboratory testing. The two pressure transducers that were tested in this program were the VEGA D36-38 from HiTech Technologies, Inc., and the KP-1911-A from Kaman Instrumentation Corporation. Pressure transducers operate on the principle that the pressure at the location of a sensor increases directly with the depth of the liquid above it. A liquid is required in order for these devices to operate. For these tests, water was first used to determine the ideal operation of the devices, then the devices were placed in a 101-SY waste tank simulant. The simulant had a specific gravity of 1.96 and had the consistency similar to the convective layer in the 101-SY waste tank. In order to determine the surface level with pressure transducers, the density of the material needs to be known

The nuclear physical method for high pressure steam manifold water level gauging and its error

International Nuclear Information System (INIS)

Li Nianzu; Li Beicheng; Jia Shengming

1993-10-01

A new method, which is non-contact on measured water level, for measuring high pressure steam manifold water level with nuclear detection technique is introduced. This method overcomes the inherent drawback of previous water level gauges based on other principles. This method can realize full range real time monitoring on the continuous water level of high pressure steam manifold from the start to full load of boiler, and the actual value of water level can be obtained. The measuring errors were analysed on site. Errors from practical operation in Tianjin Junliangcheng Power Plant and in laboratory are also presented

Investigation of earthquake factor for optimum tuned mass dampers

Science.gov (United States)

Nigdeli, Sinan Melih; Bekdaş, Gebrail

2012-09-01

In this study the optimum parameters of tuned mass dampers (TMD) are investigated under earthquake excitations. An optimization strategy was carried out by using the Harmony Search (HS) algorithm. HS is a metaheuristic method which is inspired from the nature of musical performances. In addition to the HS algorithm, the results of the optimization objective are compared with the results of the other documented method and the corresponding results are eliminated. In that case, the best optimum results are obtained. During the optimization, the optimum TMD parameters were searched for single degree of freedom (SDOF) structure models with different periods. The optimization was done for different earthquakes separately and the results were compared.

Optimum position of isolators within erbium-doped fibers

DEFF Research Database (Denmark)

Lumholt, Ole; Schüsler, Kim; Bjarklev, Anders Overgaard

1992-01-01

An isolator is used as an amplified spontaneous emission suppressing component within an erbium-doped fiber. The optimum isolator placement is both experimentally and theoretically determined and found to be slightly dependent upon pump power. Improvements of 4 dB in gain and 2 dB in noise figure...... are measured for the optimum isolator location at 25% of the fiber length when the fiber is pumped with 60 mW of pump power at 1.48 μm...

A comparison of disturbance levels measured in hypersonic tunnels using a hot-wire anemometer and a pitot pressure probe.

Science.gov (United States)

Stainback, P. C.; Wagner, R. D.

1972-01-01

Disturbance levels were measured in the test section of a Mach 5 blowdown jet using a constant-current, hot-wire anemometer and a pressure transducer. The disturbance levels, measured by the two instruments and normalized by local mean values, agreed within about 30%, with the pitot data higher than the hot-wire data. The rms disturbance levels measured with the hot-wire anemometer and converted to pitot pressures using a quasi-steady flow analysis, were about two-thirds the levels measured with the pitot probe. The variation of the normalized rms disturbance levels with stagnation pressure indicated that transition occurred in the boundary layer on the nozzle wall and influenced the outputs of the instruments located at the exit of the nozzle when the total pressure was about 35 N/sq cm. Below this pressure the disturbance levels decreased markedly. At higher pressures the disturbances were predominantly aerodynamic noise generated by the turbulent boundary layer on the nozzle wall.

High Pressure Germination of Bacillus subtilis Spores with Alterations in Levels and Types of Germination Proteins

Science.gov (United States)

2014-01-01

1ITLE AND SUBTITLE 5a CONTRACTNUMBER High pressure germination of Bacillus subtilis spores with W911NF-09-l-0286 alterations in levels and types of...A moderate high pressure (mHP) of 150 megaPascals (MPa) triggers germination of Bacillus subtilis spores via germinant receptors (GRs), while...germination by a very high pressure (vHP) of550 MPa is GR-independent. The mHP and vHP germination of Bacillus subtilis spores with different levels ofGRs

Optimum hub height of a wind turbine for maximizing annual net profit

International Nuclear Information System (INIS)

Lee, Jaehwan; Kim, Dong Rip; Lee, Kwan-Soo

2015-01-01

Highlights: • Annual Net Profit was proposed to optimize the hub height of a wind turbine. • Procedures of the hub height optimization method were introduced. • Effect of local wind speed characteristics on optimum hub height was illustrated. • Effect of rated power on optimum hub height was negligible in the range 0.75–3 MW. • Rated speed and cut-out speed had great effects on optimum hub height. - Abstract: The optimization method of the hub height, which can ensure the economic feasibility of the wind turbine, is proposed in this study. Annual Net Profit is suggested as an objective function and the optimization procedure is developed. The effects of local wind speed and wind turbine power characteristics on the optimum hub height are investigated. The optimum hub height decreased as the mean wind speed and wind shear exponent increased. Rated power had little effect on optimum hub height; it follows that the economies of scale are negligible in the rated power range of 0.75–3 MW. Among the wind turbine power characteristics, rated speed and cut-out speed most strongly affected the optimum hub height

Acceptance Test Report for the high pressure water jet system canister cleaning fixture

Energy Technology Data Exchange (ETDEWEB)

Burdin, J.R.

1995-10-25

This Acceptance Test confirmed the test results and recommendations, documented in WHC-SD-SNF-DTR-001, Rev. 0 Development Test Report for the High Pressure Water Jet System Nozzles, for decontaminating empty fuel canisters in KE-Basin. Optimum water pressure, water flow rate, nozzle size and overall configuration were tested

Acceptance Test Report for the high pressure water jet system canister cleaning fixture

International Nuclear Information System (INIS)

Burdin, J.R.

1995-01-01

This Acceptance Test confirmed the test results and recommendations, documented in WHC-SD-SNF-DTR-001, Rev. 0 Development Test Report for the High Pressure Water Jet System Nozzles, for decontaminating empty fuel canisters in KE-Basin. Optimum water pressure, water flow rate, nozzle size and overall configuration were tested

Radionuclide blood levels during cisternography of patients with normal-pressure hydrocephalus or Alzheimer's disease

International Nuclear Information System (INIS)

Mahaley, M.S. Jr.; Wilkinson, R.H. Jr.; Sivalingham, S.; Friedman, H.; Tyson, W.; Goodrich, J.K.

1974-01-01

Various diagnostic procedures were compared during investigations of 37 dementia patients undergoing differential study for normal-pressure hydrocephalus or Alzheimer's disease. A diminished radionuclide level in the blood, with abnormal cisternography and pneumoencephalography, provided the most valuable diagnostic evidence of normal-pressure hydrocephalus. (U.S.)

Effect of polishing time and pressure on quality characteristics of rice grain

International Nuclear Information System (INIS)

Karim, M.A.

2002-01-01

Since totally unpolished rice has poor cooking quality, a certain amount of polishing for the removal of the outermost bran layers is essential. To determine the best combination of polishing time and pressure with respect to obtaining optimum quantity/quality, the brown rice (head grains) of a rice strain 4048 was milled for 10, 20, 30 and 40 seconds against 1,2,3,4 and 5 lbs pressure in a Burrows McGill Polisher No. 3. the quality characteristics studied were: total milling recovery, head rice recovery, whiteness of milled rice, protein content of grain, grain length and bursting upon cooking. Both, total milled rice and head rice reduced while the whiteness of milled rice improved significantly with an increase in polishing time and or pressure. The protein content decreased gradually with an increase in time and pressure of milling but the effect was non significant. The cooked grain length increased with an increase in milling degree up to a stage, beyond which it declined. The increase in bursting of grains on cooking. A combination of 20 seconds polishing time with 2 lbs pressure or 20 seconds polishing time with 3 lbs pressure was found to be the best combination of obtaining the optimum quality as well as the quality of milled rice.(author)

Data quality assurance in pressure transducer-based automatic water level monitoring

Science.gov (United States)

Submersible pressure transducers integrated with data loggers have become relatively common water-level measuring devices used in flow or well water elevation measurements. However, drift, linearity, hysteresis and other problems can lead to erroneous data. Researchers at the USDA-ARS in Watkinsvill...

Influence of the viscoelastic properties of the respiratory system on the energetically optimum breathing frequency.

Science.gov (United States)

Bates, J H; Milic-Emili, J

1993-01-01

We hypothesized that the viscoelastic properties of the respiratory system should have significant implications for the energetically optimal frequency of breathing, in view of the fact that these properties cause marked dependencies of overall system resistance and elastance on frequency. To test our hypothesis we simulated two models of canine and human respiratory system mechanics during sinusoidal breathing and calculated the inspiratory work (WI) and pressure-time integral (PTI) per minute under both resting and exercise conditions. The two models were a two-compartment viscoelastic model and a single-compartment model. Requiring minute alveolar ventilation to be fixed, we found that both models predicted almost identical optimum breathing frequencies. The calculated PTI was very insensitive to increases in breathing frequency above the optimal frequencies, while WI was found to increase slowly with frequency above its optimum. In contrast, both WI and PTI increased sharply as frequency decreased below their respective optima. A sensitivity analysis showed that the model predictions were very insensitive to the elastance and resistance values chosen to characterize tissue viscoelasticity. We conclude that the WI criterion for choosing the frequency of breathing is compatible with observations in nature, whereas the optimal frequency predictions of the PTI are rather too high. Both criteria allow for a fairly wide margin of choice in frequency above the optimum values without incurring excessive additional energy expenditure. Furthermore, contrary to our expectations, the viscoelastic properties of the respiratory system tissues do not pose a noticeable problem to the respiratory controller in terms of energy expenditure.

Prediction of an optimum biodiesel-diesel blended fuel for compression ignition engine using GT-power

International Nuclear Information System (INIS)

Shah, A.N.; Shah, F.H.; Shahid, E.M.; Gardezi, S.A.R.

2014-01-01

This paper describes the development of a turbocharged direct-injection compression ignition (CI) engine model using fluid-dynamic engine simulation codes through a simulating tool known as GT Power. The model was first fueled with diesel, and then with various blends of biodiesel and diesel by allotting suitable parameters to predict an optimum blended fuel. During the optimization, main focus was on the engine performance, combustion, and one of the major regulated gaseous pollutants known as oxides of nitrogen (NOx). The combustion parameters such as Premix Duration (DP), Main Duration (DM), Premix Fraction (FP), Main Exponent (EM) and ignition delay (ID) affect the start of injection (SOI) angle, and thus played significant role in the prediction of optimum blended fuel. The SOI angle ranging from 5.2 to 5.7 degree crank angle (DCA) measured before top dead center (TDC) revealed an optimum biodiesel-diesel blend known as B20 (20% biodiesel and 80% diesel by volume). B20 exhibited the minimum possible NOx emissions, better combustion and acceptable engine performance. Moreover, experiments were performed to validate the simulated results by fueling the engine with B20 fuel and operating it on AC electrical dynamometer. Both the experimental and simulated results were in good agreement revealing maximum deviations of only 3%, 3.4%, 4.2%, and 5.1% for NOx, maximum combustion pressure (MCP), engine brake power (BP), and brake specific fuel consumption (BSFC), respectively. Meanwhile, a positive correlation was found between MCP and NOx showing that both the parameters are higher at lower speeds, relative to higher engine speeds. (author)

New W-and Mo-containing perovskites sythesized at high pressure

Energy Technology Data Exchange (ETDEWEB)

Sevast' yanova, L G; Burdina, K P; Zubova, E V; Venevtsev, Yu N [Moskovskij Gosudarstvennyj Univ. (USSR); Nauchno-Issledovatel' skij Fiziko-Khimicheskij Inst., Moscow (USSR))

1979-11-01

The possibility of synthesizing complex oxide W and Mo-containing compounds having a perovskite structure is shown. The optimum synthesis conditions have been defined. Critical pressure Psub(cr) has been found to equal 70 kbar, above which the perovskite structure can still exist at room temperature. The ''pressure-temperature'' diagram was used to define the stability region of perovskite of Pb(HgMo)sub(1/2)Osub(3)composition, bound by pressure p=35 to 50 kbar and a temperature of 700 deg C.

Effects of oxygen gas pressure on properties of iron oxide films grown by pulsed laser deposition

International Nuclear Information System (INIS)

Guo, Qixin; Shi, Wangzhou; Liu, Feng; Arita, Makoto; Ikoma, Yoshifumi; Saito, Katsuhiko; Tanaka, Tooru; Nishio, Mitsuhiro

2013-01-01

Highlights: ► Pulsed laser deposition is a promising technique for growing iron oxide films. ► Crystal structure of the iron oxide films strongly depends on oxygen gas pressure. ► Optimum of the oxygen gas pressure leads single phase magnetite films with high crystal quality. -- Abstract: Iron oxide films were grown on sapphire substrates by pulsed laser deposition at oxygen gas pressures between 1 × 10 −5 and 1 × 10 −1 Pa with a substrate temperature of 600 °C. Atomic force microscope, X-ray diffraction, Raman spectroscopy, X-ray absorption fine structure, and vibrational sample magnetometer analysis revealed that surface morphology and crystal structure of the iron oxide films strongly depend on the oxygen gas pressure during the growth and the optimum oxygen gas pressure range is very narrow around 1 × 10 −3 Pa for obtaining single phase magnetite films with high crystal quality

SEARCH AUTOMATION OF BINARIZATION OPTIMUM LEVEL FOR SYNTHESIZED HOLOGRAMS

Directory of Open Access Journals (Sweden)

Oleg V. Nikanorov

2017-11-01

Full Text Available The paper considers the features of synthesized holograms suitable for practical use. It is established that binary holograms are the first of all suitable ones for successful application in practice. In order to select the most suitable (optimal level of hologram binarization, we propose a criterion for estimating the quality of an image reconstructed with a binary hologram. An algorithm is developed to find the optimal level. On the basis of the conducted experiments it is established that the introduction of the developed module gives the possibility to reduce the search time of the optimal binarization level of the hologram by eleven times in comparison with manual search.

The optimum decision rules for the oddity task.

Science.gov (United States)

Versfeld, N J; Dai, H; Green, D M

1996-01-01

This paper presents the optimum decision rule for an m-interval oddity task in which m-1 intervals contain the same signal and one is different or odd. The optimum decision rule depends on the degree of correlation among observations. The present approach unifies the different strategies that occur with "roved" or "fixed" experiments (Macmillan & Creelman, 1991, p. 147). It is shown that the commonly used decision rule for an m-interval oddity task corresponds to the special case of highly correlated observations. However, as is also true for the same-different paradigm, there exists a different optimum decision rule when the observations are independent. The relation between the probability of a correct response and d' is derived for the three-interval oddity task. Tables are presented of this relation for the three-, four-, and five-interval oddity task. Finally, an experimental method is proposed that allows one to determine the decision rule used by the observer in an oddity experiment.

Effects of ambient temperature and water vapor on chamber pressure and oxygen level during low atmospheric pressure stunning of poultry.

Science.gov (United States)

Holloway, Paul H; Pritchard, David G

2017-08-01

The characteristics of the vacuum used in a low atmospheric pressure stunning system to stun (render unconscious) poultry prior to slaughter are described. A vacuum chamber is pumped by a wet screw compressor. The vacuum pressure is reduced from ambient atmospheric pressure to an absolute vacuum pressure of ∼250 Torr (∼33 kPa) in ∼67 sec with the vacuum gate valve fully open. At ∼250 Torr, the sliding gate valve is partially closed to reduce effective pumping speed, resulting in a slower rate of decreasing pressure. Ambient temperature affects air density and water vapor pressure and thereby oxygen levels and the time at the minimum total pressure of ∼160 Torr (∼21 kPa) is varied from ∼120 to ∼220 sec to ensure an effective stun within the 280 seconds of each cycle. The reduction in total pressure results in a gradual reduction of oxygen partial pressure that was measured by a solid-state electrochemical oxygen sensor. The reduced oxygen pressure leads to hypoxia, which is recognized as a humane method of stunning poultry. The system maintains an oxygen concentration of air always reduces the oxygen concentrations to a value lower than in dry air. The partial pressure of water and oxygen were found to depend on the pump down parameters due to the formation of fog in the chamber and desorption of water from the birds and the walls of the vacuum chamber. © The Author 2017. Published by Oxford University Press on behalf of Poultry Science Association.

Comparison Of Vented And Absolute Pressure Transducers For Water-Level Monitoring In Hanford Site Central Plateau Wells

International Nuclear Information System (INIS)

Mcdonald, J.P.

2011-01-01

Automated water-level data collected using vented pressure transducers deployed in Hanford Site Central Plateau wells commonly display more variability than manual tape measurements in response to barometric pressure fluctuations. To explain this difference, it was hypothesized that vented pressure transducers installed in some wells are subject to barometric pressure effects that reduce water-level measurement accuracy. Vented pressure transducers use a vent tube, which is open to the atmosphere at land surface, to supply air pressure to the transducer housing for barometric compensation so the transducer measurements will represent only the water pressure. When using vented transducers, the assumption is made that the air pressure between land surface and the well bore is in equilibrium. By comparison, absolute pressure transducers directly measure the air pressure within the wellbore. Barometric compensation is achieved by subtracting the well bore air pressure measurement from the total pressure measured by a second transducer submerged in the water. Thus, no assumption of air pressure equilibrium is needed. In this study, water-level measurements were collected from the same Central Plateau wells using both vented and absolute pressure transducers to evaluate the different methods of barometric compensation. Manual tape measurements were also collected to evaluate the transducers. Measurements collected during this study demonstrated that the vented pressure transducers over-responded to barometric pressure fluctuations due to a pressure disequilibrium between the air within the wellbores and the atmosphere at land surface. The disequilibrium is thought to be caused by the relatively long time required for barometric pressure changes to equilibrate between land surface and the deep vadose zone and may be exacerbated by the restriction of air flow between the well bore and the atmosphere due to the presence of sample pump landing plates and well caps. The

Risk-based Optimization and Reliability Levels of Coastal Structures

DEFF Research Database (Denmark)

Sørensen, John Dalsgaard; Burcharth, H. F.

Identification of optimum reliability levels for coastal structures is considered. A class of breakwaters is considered where no human injuries can be expected in cases of failure. The optimum reliability level is identified by minimizing the total costs over the service life of the structure, in...... on the minimumcost reliability levels is investigated for different values of the real rate of interest, the service lifetime, the downtime costs due to malfunction and the decommission costs.......Identification of optimum reliability levels for coastal structures is considered. A class of breakwaters is considered where no human injuries can be expected in cases of failure. The optimum reliability level is identified by minimizing the total costs over the service life of the structure...

Risk-based Optimization and Reliability Levels of Coastal Structures

DEFF Research Database (Denmark)

Sørensen, John Dalsgaard; Burcharth, Hans F.

2005-01-01

 Identification of optimum reliability levels for coastal structures is considered. A class of breakwaters is considered where no human injuries can be expected in cases of failure. The optimum reliability level is identified by minimizing the total costs over the service life of the structure, i...... on the minimumcost reliability levels is investigated for different values of the real rate of interest, the service lifetime, the downtime costs due to malfunction and the decommission costs....... Identification of optimum reliability levels for coastal structures is considered. A class of breakwaters is considered where no human injuries can be expected in cases of failure. The optimum reliability level is identified by minimizing the total costs over the service life of the structure...

Optimum discharge current waveforms for pumping Ne-like Ar soft X-ray laser

International Nuclear Information System (INIS)

Zhao Yongpeng; Jiang Shan; Xie Yao; Teng Shupeng; Wang Qi

2011-01-01

In order to enhance intensity of Ne-like Ar 46.9 nm soft X-ray laser pumped by capillary discharge, influences of main current waveform on Z-pinch process,time of lasing onset and laser intensity were studied. Rise-time of main current waveform was changed by varying conducting inductance of main switch. Experimental results with different rise-times show that amplitude of laser spike decreases with increasing rise-time,and time of lasing onset increases with increasing rise-time. In addition, influences of average current changing rate on laser intensity were studied. When inner diameter of capillary is 3 mm and initial pressure is 30 Pa, optimum average current changing rate is about 7.0 x 10 11 A/s. (authors)

The measurement for level of marine high-temperature and high-pressure vessels

International Nuclear Information System (INIS)

Lin Jie.

1986-01-01

The various error factors in measurement for level of marine high-temperature and high-pressure vessels are anslysed. The measuring method of error self compensation and its simplification for land use are shown

Determination of optimum parameters effect on kerf width of 316L stainless steel tube in Nd:YAG laser cutting

Energy Technology Data Exchange (ETDEWEB)

Ahn, J.M.; Kim, T.H. [Dept. of Metallurgical System Engineering, YONSEI Univ., Seoul (Korea); Kim, H.Y. [Korea Environment and Merchandise Testing Inst., Seoul (Korea)

2005-07-01

The effects of following four factors, which are laser power, assist gas pressure, cooling rate and scanning speed on the quality characteristics of laser cut 316L stainless steel tubes have been studied. 2{sup 4} full factorial design and central composite design were used to evaluate optimum condition of process parameters. Regression analysis was used to develop empirical models for the combined effects of the independent process parameters on laser cut quality. As the results, it was observed that laser power, assist gas pressure and scanning speeds did the major effects on kerf width. The smallest kerf width was obtained with the condition of low laser power, assist gas pressure, scanning speed and moderate cooling rate. Calculated regression model was kerf width = 64.47 + 0.91W + 1.25P + 0.41S + 0.41C{sup 2} - 0.45P{sup 2}. (orig.)

Laser-induced fluorescence detection strategies for sodium atoms and compounds in high-pressure combustors

Science.gov (United States)

Weiland, Karen J. R.; Wise, Michael L.; Smith, Gregory P.

1993-01-01

A variety of laser-induced fluorescence schemes were examined experimentally in atmospheric pressure flames to determine their use for sodium atom and salt detection in high-pressure, optically thick environments. Collisional energy transfer plays a large role in fluorescence detection. Optimum sensitivity, at the parts in 10 exp 9 level for a single laser pulse, was obtained with the excitation of the 4p-3s transition at 330 nm and the detection of the 3d-3p fluorescence at 818 nm. Fluorescence loss processes, such as ionization and amplified spontaneous emission, were examined. A new laser-induced atomization/laser-induced fluorescence detection technique was demonstrated for NaOH and NaCl. A 248-nm excimer laser photodissociates the salt molecules present in the seeded flames prior to atom detection by laser-induced fluorescence.

Seaweed intake and blood pressure levels in healthy pre-school Japanese children

Directory of Open Access Journals (Sweden)

Yamamoto Keiko

2011-08-01

Full Text Available Abstract Background Few studies have examined whether dietary factors might affect blood pressure in children. We purposed to investigate whether seaweed intake is associated with blood pressure level among Japanese preschool children. Methods The design of the study was cross-sectional and it was conducted in autumn 2006. Subjects were healthy preschoolers aged 3-6 years in Aichi, Japan. Blood pressure and pulse were measured once by an automated sphygmomanometer, which uses oscillometric methods. Dietary data, including seaweed intake, were assessed using 3-day dietary records covering 2 consecutive weekdays and 1 weekend day. Of a total of 533 children, 459 (86.1 percent agreed to be enrolled in our study. Finally, blood pressure measurement, complete dietary records and parent-reported height and weight were obtained for 223 boys and 194 girls. Results When we examined Spearman's correlation coefficients, seaweed intake was significantly negatively related to systolic blood pressure in girls (P = 0.008. In the one-way analysis of covariance for blood pressure and pulse after adjustments for age and BMI, the boys with the lowest, middle and highest tertiles of seaweed intake had diastolic blood pressure readings of 62.8, 59.3 and 59.6 mmHg, respectively (P = 0.11, trend P = 0.038. Girls with higher seaweed intake had significantly lower systolic blood pressure readings (102.4, 99.2 and 96.9 mmHg for girls with the lowest, middle and highest tertiles of seaweed intake, respectively; P = 0.037, trend P = 0.030. Conclusion Our study showed that seaweed intake was negatively related to diastolic blood pressure in boys and to systolic blood pressure in girls. This suggests that seaweed might have beneficial effects on blood pressure among children.

Optimum design of band-gap beam structures

DEFF Research Database (Denmark)

Olhoff, Niels; Niu, Bin; Cheng, Gengdong

2012-01-01

The design of band-gap structures receives increasing attention for many applications in mitigation of undesirable vibration and noise emission levels. A band-gap structure usually consists of a periodic distribution of elastic materials or segments, where the propagation of waves is impeded...... or significantly suppressed for a range of external excitation frequencies. Maximization of the band-gap is therefore an obvious objective for optimum design. This problem is sometimes formulated by optimizing a parameterized design model which assumes multiple periodicity in the design. However, it is shown...... in the present paper that such an a priori assumption is not necessary since, in general, just the maximization of the gap between two consecutive natural frequencies leads to significant design periodicity. The aim of this paper is to maximize frequency gaps by shape optimization of transversely vibrating...

Ultrasonic sludge pretreatment under pressure.

Science.gov (United States)

Le, Ngoc Tuan; Julcour-Lebigue, Carine; Delmas, Henri

2013-09-01

The objective of this work was to optimize the ultrasound (US) pretreatment of sludge. Three types of sewage sludge were examined: mixed, secondary and secondary after partial methanisation ("digested" sludge). Thereby, several main process parameters were varied separately or simultaneously: stirrer speed, total solid content of sludge (TS), thermal operating conditions (adiabatic vs. isothermal), ultrasonic power input (PUS), specific energy input (ES), and for the first time external pressure. This parametric study was mainly performed for the mixed sludge. Five different TS concentrations of sludge (12-36 g/L) were tested for different values of ES (7000-75,000 kJ/kgTS) and 28 g/L was found as the optimum value according to the solubilized chemical oxygen demand in the liquid phase (SCOD). PUS of 75-150 W was investigated under controlled temperature and the "high power input - short duration" procedure was the most effective at a given ES. The temperature increase in adiabatic US application significantly improved SCOD compared to isothermal conditions. With PUS of 150 W, the effect of external pressure was investigated in the range of 1-16 bar under isothermal and adiabatic conditions for two types of sludge: an optimum pressure of about 2 bar was found regardless of temperature conditions and ES values. Under isothermal conditions, the resulting improvement of sludge disintegration efficacy as compared to atmospheric pressure was by 22-67% and 26-37% for mixed and secondary sludge, respectively. Besides, mean particle diameter (D[4,3]) of the three sludge types decreased respectively from 408, 117, and 110 μm to about 94-97, 37-42, and 36-40 μm regardless of sonication conditions, and the size reduction process was much faster than COD extraction. Copyright © 2013 Elsevier B.V. All rights reserved.

Blood pressure load does not add to ambulatory blood pressure level for cardiovascular risk stratification

DEFF Research Database (Denmark)

Li, Yan; Thijs, Lutgarde; Boggia, José

2014-01-01

Experts proposed blood pressure (BP) load derived from 24-hour ambulatory BP recordings as a more accurate predictor of outcome than level, in particular in normotensive people. We analyzed 8711 subjects (mean age, 54.8 years; 47.0% women) randomly recruited from 10 populations. We expressed BP...... load as percentage (%) of systolic/diastolic readings ≥135/≥85 mm Hg and ≥120/≥70 mm Hg during day and night, respectively, or as the area under the BP curve (mm Hg×h) using the same ceiling values. During a period of 10.7 years (median), 1284 participants died and 1109 experienced a fatal or nonfatal...... cardiovascular end point. In multivariable-adjusted models, the risk of cardiovascular complications gradually increased across deciles of BP level and load (Pbased on 24-hour systolic or diastolic BP level (generalized R(2) statistic ≤0.294%; net...

Tutorial and Guidelines on Measurement of Sound Pressure Level in Voice and Speech

Science.gov (United States)

Švec, Jan G.; Granqvist, Svante

2018-01-01

Purpose: Sound pressure level (SPL) measurement of voice and speech is often considered a trivial matter, but the measured levels are often reported incorrectly or incompletely, making them difficult to compare among various studies. This article aims at explaining the fundamental principles behind these measurements and providing guidelines to…

Optimum design for pipe-support allocation against seismic loading

International Nuclear Information System (INIS)

Hara, Fumio; Iwasaki, Akira

1996-01-01

This paper deals with the optimum design methodology of a piping system subjected to a seismic design loading to reduce its dynamic response by selecting the location of pipe supports and whereby reducing the number of pipe supports to be used. The author employs the Genetic Algorithm for obtaining a reasonably optimum solution of the pipe support location, support capacity and number of supports. The design condition specified by the support location, support capacity and the number of supports to be used is encored by an integer number string for each of the support allocation candidates and they prepare many strings for expressing various kinds of pipe-support allocation state. Corresponding to each string, the authors evaluate the seismic response of the piping system to the design seismic excitation and apply the Genetic Algorithm to select the next generation candidates of support allocation to improve the seismic design performance specified by a weighted linear combination of seismic response magnitude, support capacity and the number of supports needed. Continuing this selection process, they find a reasonably optimum solution to the seismic design problem. They examine the feasibility of this optimum design method by investigating the optimum solution for 5, 7 and 10 degree-of-freedom models of piping system, and find that this method can offer one a theoretically feasible solution to the problem. They will be, thus, liberated from the severe uncertainty of damping value when the pipe support guaranties the design capacity of damping. Finally, they discuss the usefulness of the Genetic Algorithm for the seismic design problem of piping systems and some sensitive points when it will be applied to actual design problems

Analytical Solution for Optimum Design of Furrow Irrigation Systems

Science.gov (United States)

Kiwan, M. E.

1996-05-01

An analytical solution for the optimum design of furrow irrigation systems is derived. The non-linear calculus optimization method is used to formulate a general form for designing the optimum system elements under circumstances of maximizing the water application efficiency of the system during irrigation. Different system bases and constraints are considered in the solution. A full irrigation water depth is considered to be achieved at the tail of the furrow line. The solution is based on neglecting the recession and depletion times after off-irrigation. This assumption is valid in the case of open-end (free gradient) furrow systems rather than closed-end (closed dike) systems. Illustrative examples for different systems are presented and the results are compared with the output obtained using an iterative numerical solution method. The final derived solution is expressed as a function of the furrow length ratio (the furrow length to the water travelling distance). The function of water travelling developed by Reddy et al. is considered for reaching the optimum solution. As practical results from the study, the optimum furrow elements for free gradient systems can be estimated to achieve the maximum application efficiency, i.e. furrow length, water inflow rate and cutoff irrigation time.

Systemic arterial hypertension, blood pressure levels and associated factors in schoolchildren

Directory of Open Access Journals (Sweden)

Priscila Heleno

Full Text Available Summary Introduction: Hypertension is a major public health problem in contemporary times and it has high prevalence throughout the world. Objective: To investigate the situation of Systemic Arterial Hypertension in schoolchildren aged 6 to 10 years in Divinópolis/MG-Brazil and associated factors. Method: This is a cross-sectional, epidemiological, descriptive and analytical study, whose population was children aged 6 to 10 years enrolled in public schools in Divinópolis-MG-Brazil. Data collection was conducted from October 2014 to May 2015. Multivariate linear regressions were used to test associations between blood pressure, socioeconomic, anthropometric, dietary and physical activity. Results: The prevalence of hypertension was 15.2% in a sample of 284 children and mean values of systolic blood pressure of 101.7 (±13.2 mmHg and diastolic blood pressure of 66.0 (±11.2 mmHg. The body fat percentage showed significant differences between the genders, with 24.2 and 26.2%, respectively for boys and girls. Significant associations were made between blood pressure levels, body weight, body mass index, waist circumference, body fat percentage, consumption of yogurt, beef /chicken, beans, pizza, sandwich and some behaviors variables. Conclusion: The presented data show important aspects of school profile in the age range 6-10 years, especially related to the behavior of blood pressure.

Blood pressure levels in male carriers of Arg82Cys in CD300LG

DEFF Research Database (Denmark)

Støy, Julie; Grarup, Niels; Hørlyck, Arne

2014-01-01

found to be associated with fasting HDL-cholesterol and triglyceride levels. The polymorphism has not been detected in hypertension GWAS potentially due to its low frequency, but CD300LG has been linked to blood pressure as CD300LG knockout mice have changes in blood pressure. Twenty......-four-hour ambulatory blood pressure was obtained in human CD300LG CT-carriers to follow up on these observations. METHODS: Twenty healthy male CD300LG rs72836561 CT-carriers matched for age and BMI with 20 healthy male CC-carriers. Office blood pressure, 24-hour ambulatory blood pressure, carotid intima......-media thickness (CIMT), and fasting blood samples were evaluated. The clinical study was combined with a genetic-epidemiological study to replicate the association between blood pressure and CD300LG Arg82Cys in 2,637 men and 3,249 women. RESULTS: CT-carriers had a higher 24-hour ambulatory systolic blood pressure...

Optimum Availability of Standalone Photovoltaic Power Systems for Remote Housing Electrification

Directory of Open Access Journals (Sweden)

Tamer Khatib

2014-01-01

Full Text Available The availability of PV systems is discussed to determine the optimum availability at which standalone PV systems must be designed. Optimization methods and PV systems software, such as HOMER and PV.MY, were used for this purpose. Six PV systems with six availability levels were analyzed, in terms of wasted energy, cost of energy, battery usage, and power shortages, using real meteorological data. Results show that PV systems with 99% availability are recommended, because of their high reliability and favorably wasted energy.

Relationship of vitamin D levels to blood pressure in a biethnic population.

Science.gov (United States)

Sakamoto, R; Jaceldo-Siegl, K; Haddad, E; Oda, K; Fraser, G E; Tonstad, S

2013-08-01

Accumulating epidemiological and clinical studies have suggested that vitamin D insufficiency may be associated with hypertension. Blacks tend to have lower vitamin D levels than Whites, but it is unclear whether this difference explains the higher blood pressure (BP) observed in Blacks in a population with healthy lifestyle practices. We examined cross-sectional data in the Adventist Health Study-2 (AHS-2), a cohort of non-smoking, mostly non-drinking men and women following a range of diets from vegan to non-vegetarian. Each participant provided dietary, demographic, lifestyle and medical history data. Measurements of weight, height, waist circumference, percent body fat and blood pressure and fasting blood samples were obtained from a randomly selected non-diabetic sample of 284 Blacks and 284 Whites aged 30-95 years. Multiple regression analyses were used to assess independent relationships between blood pressure and 25(OH)D levels. Levels of 25(OH)D were inversely associated with systolic BP in Whites after control for age, gender, BMI, and use of BP-lowering medications (β-coefficient -0.23 [95% CI, -0.43, -0.03; p = 0.02]). This relationship was not seen in Blacks (β-coefficient 0.08 [95% CI, -0.14, 0.30; p = 0.4]). Results were similar when controlling for waist circumference or percentage body fat instead of BMI. No relationship between serum 25(OH)D and diastolic BP was seen. Systolic BP is inversely associated with 25(OH)D levels in Whites but not in Blacks. Vitamin D may not be a major contributor to the White-Black differential in BP. Copyright © 2012 Elsevier B.V. All rights reserved.

Determination of optimum insulation thickness in pipe for exergetic life cycle assessment

International Nuclear Information System (INIS)

Keçebaş, Ali

2015-01-01

Highlights: • It is aimed to determine optimum insulation thickness in pipe. • A new methodology is used as exergetic life cycle assessment for this purpose. • It is evaluated for various fuels, different pipe diameters and some combustion parameters. • This methodology is not suitable for determining optimum insulation thickness of a pipe. • There are benefits to our understanding of the need for insulation use in pipes. - Abstract: The energy saving and the environmental impacts’ reduction in the world building sector have gained great importance. Therefore, great efforts have been invested to create energy-saving green buildings. To do so, one of the many things to be done is the insulation of cylindrical pipes, canals and tanks. In the current study, the main focus is on the determination of the optimum insulation thickness of the pipes with varying diameters when different fuels are used. Therefore, through a new method combining exergy analysis and life cycle assessment, optimum insulation thickness of the pipes, total exergetic environmental impact, net saving and payback period were calculated. The effects of the insulation thickness on environmental and combustion parameters were analyzed in a detailed manner. The results revealed that optimum insulation thickness was affected by the temperature of the fuel when it enters into the combustion chamber, the temperature of the stack gas and the temperature of the combustion chamber. Under these optimum effects, the optimum insulation thickness of a 100 mm pipe was determined to be 55.7 cm, 57.2 cm and 59.3 cm for coal, natural gas and fuel–oil, respectively with the ratios of 76.32%, 81.84% and 84.04% net savings in the exergetic environmental impact. As the environmental impacts of the fuels and their products are bigger than those of the insulation material, the values of the optimum insulation thickness of the method used this study was found greater. Moreover, in the pipes with greater

How stem defects affect the capability of optimum bucking method?

Directory of Open Access Journals (Sweden)

Abdullah Emin Akay

2015-07-01

Full Text Available In forest harvesting activities, computer-assisted optimum bucking method increases the economic value of harvested trees. The bucking decision highly depends on the log quality grades which mainly vary with the surface characteristics such as stem defects and form of the stems. In this study, the effects of stem defects on optimum bucking method was investigated by comparing bucking applications which were conducted during the logging operations in two different Brutian Pine (Pinus brutia Ten stands. In the applications, the first stand contained the stems with relatively more stem defects than that of the stems in the second stand. The average number of defects per log for sample trees in the first and the second stand was recorded as 3.64 and 2.70, respectively. The results indicated that optimum bucking method increased the average economic value of harvested trees by 15.45% and 8.26 % in the stands, respectively. Therefore, the computer-assisted optimum bucking method potentially provides better results than that of traditional bucking method especially for the harvested trees with more stem defects.

Optimum detection for extracting maximum information from symmetric qubit sets

International Nuclear Information System (INIS)

Mizuno, Jun; Fujiwara, Mikio; Sasaki, Masahide; Akiba, Makoto; Kawanishi, Tetsuya; Barnett, Stephen M.

2002-01-01

We demonstrate a class of optimum detection strategies for extracting the maximum information from sets of equiprobable real symmetric qubit states of a single photon. These optimum strategies have been predicted by Sasaki et al. [Phys. Rev. A 59, 3325 (1999)]. The peculiar aspect is that the detections with at least three outputs suffice for optimum extraction of information regardless of the number of signal elements. The cases of ternary (or trine), quinary, and septenary polarization signals are studied where a standard von Neumann detection (a projection onto a binary orthogonal basis) fails to access the maximum information. Our experiments demonstrate that it is possible with present technologies to attain about 96% of the theoretical limit

Do high sound pressure levels of crowing in roosters necessitate passive mechanisms for protection against self-vocalization?

Science.gov (United States)

Claes, Raf; Muyshondt, Pieter G G; Dirckx, Joris J J; Aerts, Peter

2018-02-01

High sound pressure levels (>120dB) cause damage or death of the hair cells of the inner ear, hence causing hearing loss. Vocalization differences are present between hens and roosters. Crowing in roosters is reported to produce sound pressure levels of 100dB measured at a distance of 1m. In this study we measured the sound pressure levels that exist at the entrance of the outer ear canal. We hypothesize that roosters may benefit from a passive protective mechanism while hens do not require such a mechanism. Audio recordings at the level of the entrance of the outer ear canal of crowing roosters, made in this study, indeed show that a protective mechanism is needed as sound pressure levels can reach amplitudes of 142.3dB. Audio recordings made at varying distances from the crowing rooster show that at a distance of 0.5m sound pressure levels already drop to 102dB. Micro-CT scans of a rooster and chicken head show that in roosters the auditory canal closes when the beak is opened. In hens the diameter of the auditory canal only narrows but does not close completely. A morphological difference between the sexes in shape of a bursa-like slit which occurs in the outer ear canal causes the outer ear canal to close in roosters but not in hens. Copyright © 2017 Elsevier GmbH. All rights reserved.

The Effect of Rast Exercise on Plasma Levels of Apelin and Blood Pressure in Elite Women Runner

Directory of Open Access Journals (Sweden)

Shaibani Sh

2012-09-01

Full Text Available Background and Objectives: Intense exercise increases heart susceptibility to the disorder in this physiological factor.The purpose of this study is to study the effect of sprint interval training on plasma levels of apelin, blood pressure and heart rate in elite female runner. Methods: Plasma levels of apelin, Heart rate (HR & blood pressure (BP, analyzed before, after and 24 hours after exercise. 15 elite female runner, whom were playing in Shiraz track & field league, selected for this study. They all were homogenized according to any kind of disease.Results: Rast exercise made plasma level of Apelin decrease after exercise compared with plasma level before exercise and this decrease was significant (p=0.001. Also, plasma level of apelin increased significantly 24 hrs after finishing exercise (p=0.001, but there were no significant differences before exercise (p=0.375. Systolic blood pressure and heart rate increased immediately after exercise and decreased significantly after 24 hrs (p=0.001. However, significant difference was not observed in diastolic pressure before and after exercise (p=0.338.Conclusion: The finding of this study shows that sprint interval training decreases plasma levels of apelin, so we can say that apelin and blood pressure must be in balance in natural position. With knowing the role of apelin, changes in this peptide during exercise can be an alarm to cardiovascular risk factor, during or after exercise in elite athletes.

Equivalent threshold sound pressure levels (ETSPL) for Interacoustics DD 45 supra-aural audiometric earphones

DEFF Research Database (Denmark)

Poulsen, Torben

2010-01-01

This paper describes the determination and results of pure tone Equivalent Threshold Sound Pressure Levels for the Interacoustics DD45 audiometric earphone equipped with standard Model 51 cushions. The size and shape of the DD45 transducer resembles the classical Telephonics TDH 39 earphone. Pure...... tone hearing threshold measurements were performed for both ears of 29 test subjects. All audiometric frequencies from 125 Hz to 8 kHz were used. The data are intended for inclusion in future standardized Reference Equivalent Threshold Sound Pressure Levels. The results show that the DD45 may be a good...

Determination of the optimum dietary levels of cracked and cooked ...

African Journals Online (AJOL)

A 35-day feeding trial was conducted to determine the optimal dietary level(s) of cracked and cooked (CAC) jackbean meal for finisher broilers. Five diets were formulated such that they contained cracked and cooked jackbean meal al 0%, 15%, 20%, 25% and 30% levels respectively. Each diet was fed to group of 45 ...

Effect of external pressure environment on the internal noise level due to a source inside a cylindrical tank

Science.gov (United States)

Clevenson, S. A.; Roussos, L. A.

1984-01-01

A small cylindrical tank was used to study the effect on the noise environment within a tank of conditions of atmospheric (sea level) pressure or vacuum environments on the exterior. Experimentally determined absorption coefficients were used to calculate transmission loss, transmissibility coefficients and the sound pressure (noise) level differences in the interior. The noise level differences were also measured directly for the two exterior environments and compared to various analytical approximations with limited agreement. Trend study curves indicated that if the tank transmission loss is above 25 dB, the difference in interior noise level between the vacuum and ambient pressure conditions are less than 2 dB.

Low level neutron monitoring using high pressure 3He detectors

International Nuclear Information System (INIS)

Pszona, S.

1995-01-01

Three detectors, two spherical proportional counters and an ionisation chamber, all filled with 3 He to pressures of 160 kPa, 325 kPa and 1 MPa respectively have been experimentally studied with respect to their use for low level neutron monitoring. The ambient dose equivalent responses and the energy resolutions of these detectors have been determined. It is shown that spectral analysis of the signals from these detectors not only gives high sensitivity with regard to ambient dose equivalent but also improves the quality of the measurements. A special instrumentation for low level neutron monitoring is described in which a quality control method has been implemented. (Author)

Vascular flow reserve as a link between long-term blood pressure level and physical performance capacity in mammals

DEFF Research Database (Denmark)

Poulsen, Christian B; Damkjær, Mads; Hald, Bjørn O

2016-01-01

Mean arterial pressure (MAP) is surprisingly similar across different species of mammals, and it is, in general, not known which factors determine the arterial pressure level. Mammals often have a pronounced capacity for sustained physical performance. This capacity depends on the vasculature...... having a flow reserve that comes into play as tissue metabolism increases. We hypothesize that microvascular properties allowing for a large vascular flow reserve is linked to the level of the arterial pressure.To study the interaction between network properties and network inlet pressure, we developed...

NOAA Daily Optimum Interpolation Sea Surface Temperature

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NOAA 1/4° daily Optimum Interpolation Sea Surface Temperature (or daily OISST) is an analysis constructed by combining observations from different platforms...

Optimum Design of Gravity Retaining Walls Using Charged System Search Algorithm

Directory of Open Access Journals (Sweden)

S. Talatahari

2012-01-01

Full Text Available This study focuses on the optimum design retaining walls, as one of the familiar types of the retaining walls which may be constructed of stone masonry, unreinforced concrete, or reinforced concrete. The material cost is one of the major factors in the construction of gravity retaining walls therefore, minimizing the weight or volume of these systems can reduce the cost. To obtain an optimal seismic design of such structures, this paper proposes a method based on a novel meta-heuristic algorithm. The algorithm is inspired by the Coulomb's and Gauss’s laws of electrostatics in physics, and it is called charged system search (CSS. In order to evaluate the efficiency of this algorithm, an example is utilized. Comparing the results of the retaining wall designs obtained by the other methods illustrates a good performance of the CSS. In this paper, we used the Mononobe-Okabe method which is one of the pseudostatic approaches to determine the dynamic earth pressure.

Optimum fuel allocation in parallel steam generator systems

International Nuclear Information System (INIS)

Bollettini, U.; Cangioli, E.; Cerri, G.; Rome Univ. 'La Sapienza'; Trento Univ.

1991-01-01

An optimization procedure was developed to allocate fuels into parallel steam generators. The procedure takes into account the level of performance deterioration connected with the loading history (fossil fuel allocation and maintenance) of each steam generator. The optimization objective function is the system hourly cost, overall steam demand being satisfied. Costs are due to fuel and electric power supply and to plant depreciation and maintenance as well. In order to easily updata the state of each steam generator, particular care was put in the general formulation of the steam production function by adopting a special efficiency-load curve description based on a deterioration scaling parameter. The influence of the characteristic time interval length on the optimum operation result is investigated. A special implementation of the method based on minimum cost paths is suggested

Acceptance test procedure for High Pressure Water Jet System

International Nuclear Information System (INIS)

Crystal, J.B.

1995-01-01

The overall objective of the acceptance test is to demonstrate a combined system. This includes associated tools and equipment necessary to perform cleaning in the 105 K East Basin (KE) for achieving optimum reduction in the level of contamination/dose rate on canisters prior to removal from the KE Basin and subsequent packaging for disposal. Acceptance tests shall include necessary hardware to achieve acceptance of the cleaning phase of canisters. This acceptance test procedure will define the acceptance testing criteria of the high pressure water jet cleaning fixture. The focus of this procedure will be to provide guidelines and instructions to control, evaluate and document the acceptance testing for cleaning effectiveness and method(s) of removing the contaminated surface layer from the canister presently identified in KE Basin. Additionally, the desired result of the acceptance test will be to deliver to K Basins a thoroughly tested and proven system for underwater decontamination and dose reduction. This report discusses the acceptance test procedure for the High Pressure Water Jet

Improving urban African Americans' blood pressure control through multi-level interventions in the Achieving Blood Pressure Control Together (ACT) study: a randomized clinical trial.

Science.gov (United States)

Ephraim, Patti L; Hill-Briggs, Felicia; Roter, Debra L; Bone, Lee R; Wolff, Jennifer L; Lewis-Boyer, LaPricia; Levine, David M; Aboumatar, Hanan J; Cooper, Lisa A; Fitzpatrick, Stephanie J; Gudzune, Kimberly A; Albert, Michael C; Monroe, Dwyan; Simmons, Michelle; Hickman, Debra; Purnell, Leon; Fisher, Annette; Matens, Richard; Noronha, Gary J; Fagan, Peter J; Ramamurthi, Hema C; Ameling, Jessica M; Charlston, Jeanne; Sam, Tanyka S; Carson, Kathryn A; Wang, Nae-Yuh; Crews, Deidra C; Greer, Raquel C; Sneed, Valerie; Flynn, Sarah J; DePasquale, Nicole; Boulware, L Ebony

2014-07-01

Given their high rates of uncontrolled blood pressure, urban African Americans comprise a particularly vulnerable subgroup of persons with hypertension. Substantial evidence has demonstrated the important role of family and community support in improving patients' management of a variety of chronic illnesses. However, studies of multi-level interventions designed specifically to improve urban African American patients' blood pressure self-management by simultaneously leveraging patient, family, and community strengths are lacking. We report the protocol of the Achieving Blood Pressure Control Together (ACT) study, a randomized controlled trial designed to study the effectiveness of interventions that engage patient, family, and community-level resources to facilitate urban African American hypertensive patients' improved hypertension self-management and subsequent hypertension control. African American patients with uncontrolled hypertension receiving health care in an urban primary care clinic will be randomly assigned to receive 1) an educational intervention led by a community health worker alone, 2) the community health worker intervention plus a patient and family communication activation intervention, or 3) the community health worker intervention plus a problem-solving intervention. All participants enrolled in the study will receive and be trained to use a digital home blood pressure machine. The primary outcome of the randomized controlled trial will be patients' blood pressure control at 12months. Results from the ACT study will provide needed evidence on the effectiveness of comprehensive multi-level interventions to improve urban African American patients' hypertension control. Copyright © 2014 Elsevier Inc. All rights reserved.

Optimum Operational Parameters for Yawed Wind Turbines

Directory of Open Access Journals (Sweden)

David A. Peters

2011-01-01

Full Text Available A set of systematical optimum operational parameters for wind turbines under various wind directions is derived by using combined momentum-energy and blade-element-energy concepts. The derivations are solved numerically by fixing some parameters at practical values. Then, the interactions between the produced power and the influential factors of it are generated in the figures. It is shown that the maximum power produced is strongly affected by the wind direction, the tip speed, the pitch angle of the rotor, and the drag coefficient, which are specifically indicated by figures. It also turns out that the maximum power can take place at two different optimum tip speeds in some cases. The equations derived herein can also be used in the modeling of tethered wind turbines which can keep aloft and deliver energy.

Probabilistic integrity assessment of pressure tubes in an operating pressurized heavy water reactor

Energy Technology Data Exchange (ETDEWEB)

Oh, Young-Jin; Park, Heung-Bae [KEPCO E and C, 188 Gumi-dong, Bundang-gu, Seongnam-si, Gyeonggi-do 463-870 (Korea, Republic of); Lee, Jung-Min; Kim, Young-Jin [School of Mechanical Engineering, Sungkyunkwan University, 300 Chunchun-dong, Jangan-gu, Suwon-si, Gyeonggi-do 440-746 (Korea, Republic of); Ko, Han-Ok [Korea Institute of Nuclear Safety, 34 Gwahak-ro, Yuseong-gu, Daejeon-si 305-338 (Korea, Republic of); Chang, Yoon-Suk, E-mail: yschang@khu.ac.kr [Department of Nuclear Engineering, Kyung Hee University, 1 Seocheon-dong, Giheung-gu, Yongin-si, Gyeonggi-do 446-701 (Korea, Republic of)

2012-02-15

Even though pressure tubes are major components of a pressurized heavy water reactor (PHWR), only small proportions of pressure tubes are sampled for inspection due to limited inspection time and costs. Since the inspection scope and integrity evaluation have been treated by using a deterministic approach in general, a set of conservative data was used instead of all known information related to in-service degradation mechanisms because of inherent uncertainties in the examination. Recently, in order that pressure tube degradations identified in a sample of inspected pressure tubes are taken into account to address the balance of the uninspected ones in the reactor core, a probabilistic approach has been introduced. In the present paper, probabilistic integrity assessments of PHWR pressure tubes were carried out based on accumulated operating experiences and enhanced technology. Parametric analyses on key variables were conducted, which were periodically measured by in-service inspection program, such as deuterium uptake rate, dimensional change rate of pressure tube and flaw size distribution. Subsequently, a methodology to decide optimum statistical distribution by using a robust method adopting a genetic algorithm was proposed and applied to the most influential variable to verify the reliability of the proposed method. Finally, pros and cons of the alternative distributions comparing with corresponding ones derived from the traditional method as well as technical findings from the statistical assessment were discussed to show applicability to the probabilistic assessment of pressure tubes.

Development of the optimum rotor theories

DEFF Research Database (Denmark)

Okulov, Valery; Sørensen, Jens Nørkær; van Kuik, Gijs A.M.

The purpose of this study is the examination of optimum rotor theories with ideal load distributions along the blades, to analyze some of the underlying ideas and concepts, as well as to illuminate them. The book gives the historical background of the issue and presents the analysis of the problems...

Predicting optimum crop designs using crop models and seasonal climate forecasts.

Science.gov (United States)

Rodriguez, D; de Voil, P; Hudson, D; Brown, J N; Hayman, P; Marrou, H; Meinke, H

2018-02-02

Expected increases in food demand and the need to limit the incorporation of new lands into agriculture to curtail emissions, highlight the urgency to bridge productivity gaps, increase farmers profits and manage risks in dryland cropping. A way to bridge those gaps is to identify optimum combination of genetics (G), and agronomic managements (M) i.e. crop designs (GxM), for the prevailing and expected growing environment (E). Our understanding of crop stress physiology indicates that in hindsight, those optimum crop designs should be known, while the main problem is to predict relevant attributes of the E, at the time of sowing, so that optimum GxM combinations could be informed. Here we test our capacity to inform that "hindsight", by linking a tested crop model (APSIM) with a skillful seasonal climate forecasting system, to answer "What is the value of the skill in seasonal climate forecasting, to inform crop designs?" Results showed that the GCM POAMA-2 was reliable and skillful, and that when linked with APSIM, optimum crop designs could be informed. We conclude that reliable and skillful GCMs that are easily interfaced with crop simulation models, can be used to inform optimum crop designs, increase farmers profits and reduce risks.

Optimum Antenna Downtilt Angles for Macrocellular WCDMA Network

Directory of Open Access Journals (Sweden)

Niemelä Jarno

2005-01-01

Full Text Available The impact of antenna downtilt on the performance of cellular WCDMA network has been studied by using a radio network planning tool. An optimum downtilt angle has been evaluated for numerous practical macrocellular site and antenna configurations for electrical and mechanical antenna downtilt concepts. The aim of this massive simulation campaign was expected to provide an answer to two questions: firstly, how to select the downtilt angle of a macrocellular base station antenna? Secondly, what is the impact of antenna downtilt on system capacity and network coverage? Optimum downtilt angles were observed to vary between – depending on the network configuration. Moreover, the corresponding downlink capacity gains varied between – . Antenna vertical beamwidth affects clearly the required optimum downtilt angle the most. On the other hand, with wider antenna vertical beamwidth, the impact of downtilt on system performance is not such imposing. In addition, antenna height together with the size of the dominance area affect the required downtilt angle. Finally, the simulation results revealed how the importance of the antenna downtilt becomes more significant in dense networks, where the capacity requirements are typically also higher.

NOAA Optimum Interpolation (OI) SST V2

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The optimum interpolation (OI) sea surface temperature (SST) analysis is produced weekly on a one-degree grid. The analysis uses in situ and satellite SST's plus...

Estimation of a noise level using coarse-grained entropy of experimental time series of internal pressure in a combustion engine

International Nuclear Information System (INIS)

Litak, Grzegorz; Taccani, Rodolfo; Radu, Robert; Urbanowicz, Krzysztof; HoIyst, Janusz A.; Wendeker, MirosIaw; Giadrossi, Alessandro

2005-01-01

We report our results on non-periodic experimental time series of pressure in a single cylinder spark ignition engine. The experiments were performed for different levels of loading. We estimate the noise level in internal pressure calculating the coarse-grained entropy from variations of maximal pressures in successive cycles. The results show that the dynamics of the combustion is a non-linear multidimensional process mediated by noise. Our results show that so defined level of noise in internal pressure is not monotonous function of loading

Finding the Optimum Scenario in Risk-benefit Assessment: An Example on Vitamin D

DEFF Research Database (Denmark)

Berjia, Firew Lemma; Hoekstra, J.; Verhagen, H.

2014-01-01

an optimum scenario that provides maximum net health gain in health risk-benefit assessment of dietary exposure as expressed by serum vitamin D level. With regard to the vitamin D assessment, a considerable health gain is observed due to the reduction of risk of other cause mortality, fall and hip fractures......Background: In risk-benefit assessment of food and nutrients, several studies so far have focused on comparison of two scenarios to weigh the health effect against each other. One obvious next step is finding the optimum scenario that provides maximum net health gains. Aim: This paper aims to show...... that provides maximum net health gains. As a common health metric, Disability Adjusted Life Years (DALY) has been used to project the net health effect by using the QALIBRA (Quality of Life for Benefit Risk Assessment) software. Results: The method used in the vitamin D example shows that it is feasible to find...

Multidisciplinary Aerodynamic Design of a Rotor Blade for an Optimum Rotor Speed Helicopter

Directory of Open Access Journals (Sweden)

Jiayi Xie

2017-06-01

Full Text Available The aerodynamic design of rotor blades is challenging, and is crucial for the development of helicopter technology. Previous aerodynamic optimizations that focused only on limited design points find it difficult to balance flight performance across the entire flight envelope. This study develops a global optimum envelope (GOE method for determining blade parameters—blade twist, taper ratio, tip sweep—for optimum rotor speed helicopters (ORS-helicopters, balancing performance improvements in hover and various freestream velocities. The GOE method implements aerodynamic blade design by a bi-level optimization, composed of a global optimization step and a secondary optimization step. Power loss as a measure of rotor performance is chosen as the objective function, referred to as direct power loss (DPL in this study. A rotorcraft comprehensive code for trim simulation with a prescribed wake method is developed. With the application of the GOE method, a DPL reduction of as high as 16.7% can be achieved in hover, and 24% at high freestream velocity.

Optimum tilt angle and orientation for solar collectors in Syria

International Nuclear Information System (INIS)

Skeiker, Kamal

2009-01-01

One of the important parameters that affect the performance of a solar collector is its tilt angle with the horizon. This is because of the variation of tilt angle changes the amount of solar radiation reaching the collector surface. A mathematical model was used for estimating the solar radiation on a tilted surface, and to determine the optimum tilt angle and orientation (surface azimuth angle) for the solar collector in the main Syrian zones, on a daily basis, as well as for a specific period. The optimum angle was computed by searching for the values for which the radiation on the collector surface is a maximum for a particular day or a specific period. The results reveal that changing the tilt angle 12 times in a year (i.e. using the monthly optimum tilt angle) maintains approximately the total amount of solar radiation near the maximum value that is found by changing the tilt angle daily to its optimum value. This achieves a yearly gain in solar radiation of approximately 30% more than the case of a solar collector fixed on a horizontal surface.

Direct measured systolic pressure gradients across the aorto-iliac segment in multiple-level-obstruction arteriosclerosis

DEFF Research Database (Denmark)

Noer, Ivan; Praestholm, J; Tønnesen, K H

1981-01-01

Patients with severe ischemia due to multi-level obstructions in the leg arteries both above and below the region were assessed preoperatively by intraarterial brachial and femoral artery pressure measurements. The systolic pressure drop along aorto-iliac obstructions was compared to the angiogra....... Due to large variations, however, the angiographic information was found to be useless in the individual patient. No difference in the pressure drop was found between cases in which rich and poor collateral networks were visualized....

Automated Decisional Model for Optimum Economic Order Quantity Determination Using Price Regressive Rates

Science.gov (United States)

Roşu, M. M.; Tarbă, C. I.; Neagu, C.

2016-11-01

The current models for inventory management are complementary, but together they offer a large pallet of elements for solving complex problems of companies when wanting to establish the optimum economic order quantity for unfinished products, row of materials, goods etc. The main objective of this paper is to elaborate an automated decisional model for the calculus of the economic order quantity taking into account the price regressive rates for the total order quantity. This model has two main objectives: first, to determine the periodicity when to be done the order n or the quantity order q; second, to determine the levels of stock: lighting control, security stock etc. In this way we can provide the answer to two fundamental questions: How much must be ordered? When to Order? In the current practice, the business relationships with its suppliers are based on regressive rates for price. This means that suppliers may grant discounts, from a certain level of quantities ordered. Thus, the unit price of the products is a variable which depends on the order size. So, the most important element for choosing the optimum for the economic order quantity is the total cost for ordering and this cost depends on the following elements: the medium price per units, the stock cost, the ordering cost etc.

Optimum supervision intervals and order of supervision in nuclear reactor protective systems

International Nuclear Information System (INIS)

Kontoleon, J.M.

1978-01-01

The optimum inspection strategy of an m-out-of-n:G nuclear reactor protective system with nonidentical units is analyzed. A 2-out-of-4:G system is used to formulate a multi-variable optimization problem to determine (a) the optimum order of supervision of the units and (b) the optimum supervision intervals between units. The case of systems with identical units is a special case of the above. Numerical results are derived using a computer algorithm

Optimum pelvic incidence minus lumbar lordosis value can be determined by individual pelvic incidence.

Science.gov (United States)

Inami, Satoshi; Moridaira, Hiroshi; Takeuchi, Daisaku; Shiba, Yo; Nohara, Yutaka; Taneichi, Hiroshi

2016-11-01

Adult spinal deformity (ASD) classification showing that ideal pelvic incidence minus lumbar lordosis (PI-LL) value is within 10° has been received widely. But no study has focused on the optimum level of PI-LL value that reflects wide variety in PI among patients. This study was conducted to determine the optimum PI-LL value specific to an individual's PI in postoperative ASD patients. 48 postoperative ASD patients were recruited. Spino-pelvic parameters and Oswestry Disability Index (ODI) were measured at the final follow-up. Factors associated with good clinical results were determined by stepwise multiple regression model using the ODI. The patients with ODI under the 75th percentile cutoff were designated into the "good" health related quality of life (HRQOL) group. In this group, the relationship between the PI-LL and PI was assessed by regression analysis. Multiple regression analysis revealed PI-LL as significant parameters associated with ODI. Thirty-six patients with an ODI <22 points (75th percentile cutoff) were categorized into a good HRQOL group, and linear regression models demonstrated the following equation: PI-LL = 0.41PI-11.12 (r = 0.45, P = 0.0059). On the basis of this equation, in the patients with a PI = 50°, the PI-LL is 9°. Whereas in those with a PI = 30°, the optimum PI-LL is calculated to be as low as 1°. In those with a PI = 80°, PI-LL is estimated at 22°. Consequently, an optimum PI-LL is inconsistent in that it depends on the individual PI.

Determination of optimum filter in inferolateral view of myocardial SPECT

International Nuclear Information System (INIS)

Takavar; Eftekhari, M.; Fallahi, B.; Shamsipour, Gh.; Sohrabi, M.; Saghari, M.

2004-01-01

Background: In myocardial perfusion SPECT imaging, images are degraded by photon attenuation, distance-dependent collimator, detector response and photon scattering. As filters greatly affect quality of nuclear medicine images, in this study determination of optimum filter for inferolateral view is our prime objective. Materials and Methods: .A phantom simulating heart left ventricle was built. About 1mCi of 99m Tc, was injected into the phantom. Images were taken from this phantom. Parzen, Hamming, Hanning, Butter worth and Gaussian filters were exerted on the images obtained from the phantom.. By defining some criteria such as contrast, signal to noise ratio, and defect size delectability, the best filter was determined for our ADAC spect system at our nuclear medicine center. In this study, 27 patients who previously had undergone coronary angiography were chosen to be included. All of these patients revealed significant stenosis in the left circumflex artery. Myocardial SPECT images of these patients had inferolateral defect. The images of these patients were processed with 12 filters including the optimum filters obtained from phantom study and some other non-optimum filters. A nuclear medicine physician quantified the results by assigmng mark from 0 to 4. to every image. 0 mark for images that didn't show the defect properly and 4 for the best one. The data from patient study were analyzed with non-related, non -parametric Friedman test. Results: Nyquist frequency of 0.325 and 0.5 were obtained as the optimum cut-off frequencies for hamming and Hanning filters respectively. Order 11 and cut-off frequency of 0.45 and order 20. with cut-off frequency of 0.5 were found to be optimum for Butter worth and Gaussian filters. In patient studies it was found that, Butter worth filter with cut-off frequency of 0.45 and order of 11 produced the best quality images. Conclusion: In this study. Butter worth filter with cut-off frequency of 0.45 and order of 11 was the

An accurate estimation and optimization of bottom hole back pressure in managed pressure drilling

Directory of Open Access Journals (Sweden)

Boniface Aleruchi ORIJI

2017-06-01

Full Text Available Managed Pressure Drilling (MPD utilizes a method of applying back pressure to compensate for wellbore pressure losses during drilling. Using a single rheological (Annular Frictional Pressure Losses, AFPL model to estimate the backpressure in MPD operations for all sections of the well may not yield the best result. Each section of the hole was therefore treated independently in this study as data from a case study well were used. As the backpressure is a function of hydrostatic pressure, pore pressure and AFPL, three AFPL models (Bingham plastic, Power law and Herschel Bulkley models were utilized in estimating the backpressure. The estimated backpressure values were compared to the actual field backpressure values in order to obtain the optimum backpressure at the various well depths. The backpressure values estimated by utilizing the power law AFPL model gave the best result for the 12 1/4" hole section (average error % of 1.855% while the back pressures estimated by utilizing the Herschel Bulkley AFPL model gave the best result for the 8 1/2" hole section (average error % of 12.3%. The study showed that for hole sections of turbulent annular flow, the power law AFPL model fits best for estimating the required backpressure while for hole sections of laminar annular flow, the Herschel Bulkley AFPL model fits best for estimating the required backpressure.

THE HABITABLE ZONE OF EARTH-LIKE PLANETS WITH DIFFERENT LEVELS OF ATMOSPHERIC PRESSURE

Energy Technology Data Exchange (ETDEWEB)

Vladilo, Giovanni; Murante, Giuseppe; Silva, Laura [INAF-Trieste Astronomical Observatory, Trieste (Italy); Provenzale, Antonello [Institute of Atmospheric Sciences and Climate-CNR, Torino (Italy); Ferri, Gaia; Ragazzini, Gregorio, E-mail: vladilo@oats.inaf.it [Department of Physics, University of Trieste, Trieste (Italy)

2013-04-10

As a contribution to the study of the habitability of extrasolar planets, we implemented a one-dimensional energy balance model (EBM), the simplest seasonal model of planetary climate, with new prescriptions for most physical quantities. Here we apply our EBM to investigate the surface habitability of planets with an Earth-like atmospheric composition but different levels of surface pressure. The habitability, defined as the mean fraction of the planet's surface on which liquid water could exist, is estimated from the pressure-dependent liquid water temperature range, taking into account seasonal and latitudinal variations of surface temperature. By running several thousands of EBM simulations we generated a map of the habitable zone (HZ) in the plane of the orbital semi-major axis, a, and surface pressure, p, for planets in circular orbits around a Sun-like star. As pressure increases, the HZ becomes broader, with an increase of 0.25 AU in its radial extent from p = 1/3 to 3 bar. At low pressure, the habitability is low and varies with a; at high pressure, the habitability is high and relatively constant inside the HZ. We interpret these results in terms of the pressure dependence of the greenhouse effect, the efficiency of horizontal heat transport, and the extent of the liquid water temperature range. Within the limits discussed in the paper, the results can be extended to planets in eccentric orbits around non-solar-type stars. The main characteristics of the pressure-dependent HZ are modestly affected by variations of planetary properties, particularly at high pressure.

THE HABITABLE ZONE OF EARTH-LIKE PLANETS WITH DIFFERENT LEVELS OF ATMOSPHERIC PRESSURE

International Nuclear Information System (INIS)

Vladilo, Giovanni; Murante, Giuseppe; Silva, Laura; Provenzale, Antonello; Ferri, Gaia; Ragazzini, Gregorio

2013-01-01

As a contribution to the study of the habitability of extrasolar planets, we implemented a one-dimensional energy balance model (EBM), the simplest seasonal model of planetary climate, with new prescriptions for most physical quantities. Here we apply our EBM to investigate the surface habitability of planets with an Earth-like atmospheric composition but different levels of surface pressure. The habitability, defined as the mean fraction of the planet's surface on which liquid water could exist, is estimated from the pressure-dependent liquid water temperature range, taking into account seasonal and latitudinal variations of surface temperature. By running several thousands of EBM simulations we generated a map of the habitable zone (HZ) in the plane of the orbital semi-major axis, a, and surface pressure, p, for planets in circular orbits around a Sun-like star. As pressure increases, the HZ becomes broader, with an increase of 0.25 AU in its radial extent from p = 1/3 to 3 bar. At low pressure, the habitability is low and varies with a; at high pressure, the habitability is high and relatively constant inside the HZ. We interpret these results in terms of the pressure dependence of the greenhouse effect, the efficiency of horizontal heat transport, and the extent of the liquid water temperature range. Within the limits discussed in the paper, the results can be extended to planets in eccentric orbits around non-solar-type stars. The main characteristics of the pressure-dependent HZ are modestly affected by variations of planetary properties, particularly at high pressure.

Diode Laser Detection of Greenhouse Gases in the Near-Infrared Region by Wavelength Modulation Spectroscopy: Pressure Dependence of the Detection Sensitivity

Directory of Open Access Journals (Sweden)

Takashi Asakawa

2010-05-01

Full Text Available We have investigated the pressure dependence of the detection sensitivity of CO2, N2O and CH4 using wavelength modulation spectroscopy (WMS with distributed feed-back diode lasers in the near infrared region. The spectral line shapes and the background noise of the second harmonics (2f detection of the WMS were analyzed theoretically. We determined the optimum pressure conditions in the detection of CO2, N2O and CH4, by taking into consideration the background noise in the WMS. At the optimum total pressure for the detection of CO2, N2O and CH4, the limits of detection in the present system were determined.

Optimum design of a nuclear heat supply

International Nuclear Information System (INIS)

Borel, J.P.

1984-01-01

This paper presents an economic analysis for the optimum design of a nuclear heat supply to a given district-heating network. First, a general description of the system is given, which includes a nuclear power plant, a heating power plant and a district-heating network. The heating power plant is fed with steam from the nuclear power plant. It is assumed that the heating network is already in operation and that the nuclear power plant was previously designed to supply electricity. Second, a technical definition of the heat production and transportation installations is given. The optimal power of these installations is examined. The main result is a relationship between the network capacity and the level of the nuclear heat supply as a substitute for oil under the best economic conditions. The analysis also presents information for choosing the best operating mode. Finally, the heating power plant is studied in more detail from the energy, technical and economic aspects. (author)

Evaluation of the Automatic Density Compensation for Pressurizer Level Measurement

International Nuclear Information System (INIS)

Jeong, Insoo; Min, Seohong; Ahn, Myunghoon

2014-01-01

When using two transmitters, it is difficult for the operators to identify the correct level of the pressurizer (PZR) upon failure of one of the two transmitters. For this reason, Korean Utility Requirements Document (KURD) requires that the operators to use three independent level indicators. Two hot calibrated transmitters and one cold calibrated transmitter compose PZR level transmitters in APR1400. In this paper, the deviation between cold calibration and hot calibration is evaluated, and the application of compensated PZR level measurement and uncompen-sated PZR level measurement during the normal operation of APR1400 are introduced. The PZR level signals for APR1400 come in three channels. To satisfy the KURD requirements for PZR level measurement, and at the same time to accomplish correction design and implementation, applicability and differences between hot calibration and cold calibration, compensated level and uncompensated level were evaluated as follows: For proper indication of PZR levels under normal operating condition, two of the three transmitters went through hot calibration and the remaining one transmitter went through cold calibration. This was to allow indicating entire regions of PZR regardless of the plant operation modes. For automatic density compensation per KURD requirements, the algorithm of the density compensated PZR level implemented in the DCS controller and PRV logic is adopted as a signal validation method

[Study on relationship between prevalence or co-prevalence of risk factors for cardiovascular disease and blood pressure level in adults in China].

Science.gov (United States)

Chen, Z H; Zhang, M; Li, Y C; Zhao, Z P; Zhang, X; Huang, Z J; Li, C; Wang, L M

2018-05-10

Objective: To study the relationship between blood pressure level and major risk factors for cardiovascular diseases in adults in China. Methods: A total of 179 347 adults aged ≥18 years were recruited from 298 surveillance points in 31 provinces in China in 2013 through complex multistage stratified sampling. The survey included face to face interview and physical examination to collect information about risk factors, such as smoking, drinking, diet pattern, physical activity, overweight or obesity, and the prevalence of hypertension. The blood pressure was classified into 6 levels (ideal blood pressure, normal blood pressure, normal high blood pressure and hypertension phase Ⅰ, Ⅱ and Ⅲ). The relationship between the prevalence or co-prevalence of risk factors for cardiovascular disease and blood pressure was analyzed. Results: The adults with ideal blood pressure, normal blood pressure, normal high pressure, hypertension phase Ⅰ, Ⅱ and Ⅲ accounted for 36.14 % , 22.77 % , 16.22 % , 16.43 % , 5.97 % and 2.48 % , respectively. Among them, the blood pressure was higher in men, people in Han ethnic group and those married, and the blood pressure was higher in those with older age, lower income level and lower education level, the differences were all significant ( P blood pressure levels of both sexes ( P blood pressure levels of those taking no antihypertensive drug was influenced more by the co-prevalence of risk factors. Finally, multiple logistic analysis showed that the risks for high blood pressure in adults with 1, 2 and ≥3 risk factors were 1.36, 1.79 and 2.38 times higher, respectively, than that of the adults without risk factor. Conclusion: The more the risk factors for cardiovascular disease in adults, the higher their blood pressure were. It is necessary to conduct comprehensive behavior intervention targeting ≥ 2 risk factors for the better control of blood pressure in general population.

Relationship of blood lead levels and blood pressure in NHANES II: additional calculations

International Nuclear Information System (INIS)

Gartside, P.S.

1988-01-01

In performing research for associations and relationships among the data thus far published from the NHANES II survey, only the data for the 64 communities involved may be used. The simple omission of a few essential data makes impossible any valid analysis from the data for the 20,325 individual respondents. In this research for associations between blood lead levels and blood pressure in NHANES II, the method of forward stepwise regression was used. This avoids the problem of inflated error rates for blood lead, maximizes the number of data analyzed, and minimizes the number of independent variables entered into the regression model, thus avoiding the pitfalls that previous NHANES II research of blood lead and blood pressure has fallen into when using backward stepwise regression. The results of this research for white male adults, white female adults, and black adults were contradictory and lacked consistency and reliability. In addition, the overall average association between blood lead level and blood pressure was so minute that the only rational conclusion is that there is no evidence for this association to be found in the NHANES II data

46 CFR 52.01-110 - Water-level indicators, water columns, gauge-glass connections, gauge cocks, and pressure gauges...

Science.gov (United States)

2010-10-01

... § 52.01-110 Water-level indicators, water columns, gauge-glass connections, gauge cocks, and pressure... 46 Shipping 2 2010-10-01 2010-10-01 false Water-level indicators, water columns, gauge-glass connections, gauge cocks, and pressure gauges (modifies PG-60). 52.01-110 Section 52.01-110 Shipping COAST...

EFFECTS OF PRESS PRESSURE ON GLUE LINE THICKNESS AND PROPERTIES OF LAMINATED VENEER LUMBER GLUED WITH MELAMINE UREA FORMALDEHYDE ADHESIVE

Directory of Open Access Journals (Sweden)

Ramazan Kurt,

2012-07-01

Full Text Available Laminated veneer lumbers (LVLs were manufactured from half-round sliced I-214 hybrid poplar clone veneers with MUF adhesives using press pressures ranging from 2.5 to 15 kg cm-2. The results showed that the press pressures affected the glue line thickness (GLT and the physical and mechanical properties of the LVLs. Higher specific gravity (SG and mechanical properties, but lower GLT were developed as a result of using higher press pressures. The optimum press pressure was found to be 10 kg cm-2 in relation to GLT, SG, and mechanical properties. Significant linear correlations were found between GLT and mechanical properties. GLT can be used to determine the quality of wood bonding and may become a valuable tool for this purpose. Reliable data on the optimum GLT and press pressures can be used to design safe wood bonding applications in all aspects of wood based composites, as well as wood constructions when appropriate techniques are adopted to measure the GLT.

Optimum structure of Whipple shield against hypervelocity impact

International Nuclear Information System (INIS)

Lee, M

2014-01-01

Hypervelocity impact of a spherical aluminum projectile onto two spaced aluminum plates (Whipple shield) was simulated to estimate an optimum structure. The Smooth Particle Hydrodynamics (SPH) code which has a unique migration scheme from a rectangular coordinate to an axisymmetic coordinate was used. The ratio of the front plate thickness to sphere diameter varied from 0.06 to 0.48. The impact velocities considered here were 6.7 km/s. This is the procedure we explored. To guarantee the early stage simulation, the shapes of debris clouds were first compared with the previous experimental pictures, indicating a good agreement. Next, the debris cloud expansion angle was predicted and it shows a maximum value of 23 degree for thickness ratio of front bumper to sphere diameter of 0.23. A critical sphere diameter causing failure of rear wall was also examined while keeping the total thickness of two plates constant. There exists an optimum thickness ratio of front bumper to rear wall, which is identified as a function of the size combination of the impacting body, front and rear plates. The debris cloud expansion-correlated-optimum thickness ratio study provides a good insight on the hypervelocity impact onto spaced target system.

Optimum structure of Whipple shield against hypervelocity impact

Science.gov (United States)

Lee, M.

2014-05-01

Hypervelocity impact of a spherical aluminum projectile onto two spaced aluminum plates (Whipple shield) was simulated to estimate an optimum structure. The Smooth Particle Hydrodynamics (SPH) code which has a unique migration scheme from a rectangular coordinate to an axisymmetic coordinate was used. The ratio of the front plate thickness to sphere diameter varied from 0.06 to 0.48. The impact velocities considered here were 6.7 km/s. This is the procedure we explored. To guarantee the early stage simulation, the shapes of debris clouds were first compared with the previous experimental pictures, indicating a good agreement. Next, the debris cloud expansion angle was predicted and it shows a maximum value of 23 degree for thickness ratio of front bumper to sphere diameter of 0.23. A critical sphere diameter causing failure of rear wall was also examined while keeping the total thickness of two plates constant. There exists an optimum thickness ratio of front bumper to rear wall, which is identified as a function of the size combination of the impacting body, front and rear plates. The debris cloud expansion-correlated-optimum thickness ratio study provides a good insight on the hypervelocity impact onto spaced target system.

Effect of sample matrix composition on INAA sample weights, measurement precisions, limits of detection, and optimum conditions

International Nuclear Information System (INIS)

Guinn, V.P.; Nakazawa, L.; Leslie, J.

1984-01-01

The instrumental neutron activation analysis (INAA) Advance Prediction Computer Program (APCP) is extremely useful in guiding one to optimum subsequent experimental analyses of samples of all types of matrices. By taking into account the contributions to the cumulative Compton-continuum levels from all significant induced gamma-emitting radionuclides, it provides good INAA advance estimates of detectable photopeaks, measurement precisions, concentration lower limits of detection (LOD's) and optimum irradiation/decay/counting conditions - as well as of the very important maximum allowable sample size for each set of conditions calculated. The usefulness and importance of the four output parameters cited in the title are discussed using the INAA APCP outputs for NBS SRM-1632 Coal as the example

Optimum Arrangement of Reactive Power Sources While Using Genetic Algori

Directory of Open Access Journals (Sweden)

A. M. Gashimov

2010-01-01

Full Text Available Reduction of total losses in distribution electricity supply network is considered as an important measure which serves for improvement of efficiency of electric power supply systems. This objective can be achieved by optimum distribution of reactive power sources in proper places of distribution electricity supply network. The proposed methodology is based on application of a genetic algorithm. Total expenses for installation of capacitor banks, their operation and also expenses related to electric power losses are considered as an efficiency function which is used for determination of places with optimum values of capacitor bank power. The methodology is the most efficient for selection of optimum places in the network where it is necessary to install capacitor banks with due account of their power control depending on a switched-on load value in the units.

An automated optimization of core fuel loading pattern for pressurized water reactors

International Nuclear Information System (INIS)

Chen Renji

1988-11-01

An optimum method was adopted to search for an optimum fuel loading pattern in pressurized water reactors. A radial power peak factor was chosen as the objective function of the optimum loading. The direct search method with shuffling rules is used to find optimum solution. The search for an optimum loading pattern with the smallest radial power peak by exchanging fuel assemblies was made. The search process is divided into two steps. In the first step fresh fuels or high reactivity fuels are arranged which are placed in core interior to have a reasonable fuel loading pattern. To further reduce the radial power peak factor, the second step will be necessary to rearrange the exposed lower reactivity fuel around the assemblies which has the radial power peak. In optimum process 1.5 group coarse mesh diffusion theory or two group nodal Green function diffusion theory is utilized to calculate the two dimensional power distribution after each shuffle. Also, above two methods are combinatively utilized to calculate the state quantity. It is not only true to save CPU time, but also can obtian exact results. Besides above function, the code MSOFEL is used to search critical boron concentration and to predict burn-up. The code has been written with FORTRAN-4. The optimum loading pattern was chosen for OCONEE and QINSHAN nuclear power plants as reference examples. The validity and feasibility of MSOFEL was demonstrated

A methodological framework to determine optimum durations for the construction of soil water characteristic curves using centrifugation

Directory of Open Access Journals (Sweden)

Vero Sara E.

2016-12-01

Full Text Available During laboratory assessment of the soil water characteristic curve (SWCC, determining equilibrium at various pressures is challenging. This study establishes a methodological framework to identify appropriate experimental duration at each pressure step for the construction of SWCCs via centrifugation. Three common temporal approaches to equilibrium – 24-, 48- and 72-h – are examined, for a grassland and arable soil. The framework highlights the differences in equilibrium duration between the two soils. For both soils, the 24-h treatment significantly overestimated saturation. For the arable site, no significant difference was observed between the 48- and 72-h treatments. Hence, a 48-h treatment was sufficient to determine ‘effective equilibrium’. For the grassland site, the 48- and 72-h treatments differed significantly. This highlights that a more prolonged duration is necessary for some soils to conclusively determine that effective equilibrium has been reached. This framework can be applied to other soils to determine the optimum centrifuge durations for SWCC construction.

Prediction of the optimum hybridization conditions of dot-blot-SNP analysis using estimated melting temperature of oligonucleotide probes.

Science.gov (United States)

Shiokai, Sachiko; Kitashiba, Hiroyasu; Nishio, Takeshi

2010-08-01

Although the dot-blot-SNP technique is a simple cost-saving technique suitable for genotyping of many plant individuals, optimization of hybridization and washing conditions for each SNP marker requires much time and labor. For prediction of the optimum hybridization conditions for each probe, we compared T (m) values estimated from nucleotide sequences using the DINAMelt web server, measured T (m) values, and hybridization conditions yielding allele-specific signals. The estimated T (m) values were comparable to the measured T (m) values with small differences of less than 3 degrees C for most of the probes. There were differences of approximately 14 degrees C between the specific signal detection conditions and estimated T (m) values. Change of one level of SSC concentrations of 0.1, 0.2, 0.5, and 1.0x SSC corresponded to a difference of approximately 5 degrees C in optimum signal detection temperature. Increasing the sensitivity of signal detection by shortening the exposure time to X-ray film changed the optimum hybridization condition for specific signal detection. Addition of competitive oligonucleotides to the hybridization mixture increased the suitable hybridization conditions by 1.8. Based on these results, optimum hybridization conditions for newly produced dot-blot-SNP markers will become predictable.

Optimum analysis of pavement maintenance using multi-objective genetic algorithms

Directory of Open Access Journals (Sweden)

Amr A. Elhadidy

2015-04-01

Full Text Available Road network expansion in Egypt is considered as a vital issue for the development of the country. This is done while upgrading current road networks to increase the safety and efficiency. A pavement management system (PMS is a set of tools or methods that assist decision makers in finding optimum strategies for providing and maintaining pavements in a serviceable condition over a given period of time. A multi-objective optimization problem for pavement maintenance and rehabilitation strategies on network level is discussed in this paper. A two-objective optimization model considers minimum action costs and maximum condition for used road network. In the proposed approach, Markov-chain models are used for predicting the performance of road pavement and to calculate the expected decline at different periods of time. A genetic-algorithm-based procedure is developed for solving the multi-objective optimization problem. The model searched for the optimum maintenance actions at adequate time to be implemented on an appropriate pavement. Based on the computing results, the Pareto optimal solutions of the two-objective optimization functions are obtained. From the optimal solutions represented by cost and condition, a decision maker can easily obtain the information of the maintenance and rehabilitation planning with minimum action costs and maximum condition. The developed model has been implemented on a network of roads and showed its ability to derive the optimal solution.

Connection of optimum temporal exponents with a principle of least action

Science.gov (United States)

Sergeev, E. V.; Karzanov, A. V.; Tremaskin, A. V.

2008-06-01

The principle of the least action states, that the motion of objects on optimum trajectories conjugates to the underload expenditure of activity. In the canonical approach this statement is reduced to searching extreme activity. For the immediate proof of the underload expenditure of activity on optimum trajectories the relevant mathematical algorithm in the basis of which bottom the concept of optimum time exponents lays is offered. Using this algorithm, various modes of a motion of charged particles are explored: the harmonic motion, a motion in the homogeneous force field, a motion in a central force field and a motion on inertia. The terrain clearance minimum under the rate of flux of activity for the harmonic motions is detected.

Containment structure optimization

International Nuclear Information System (INIS)

Putman, S.; Walser, A.

1979-01-01

The major design features investigated are: dome shape, the prestress level provided to counteract accident pressure, the effect of diameter variation, and the design pressure used to size the containment. The optimum dome shape and optimum prestress level are used to investigate the effect of variations in diameter and design pressure on containment cost. The containment internal diameter is fixed at 150 feet for investigation of dome shape, prestress level and design prestress. A hemispherical dome containment with a prestress level of 1.25 P/sub a/ is recommended regardless of design pressure selected. A design pressure of 60 psi is recommended. No significant cost penalty is associated with diameter variation in the range of 145 to 155 feet

Lava lake level as a gauge of magma reservoir pressure and eruptive hazard

Science.gov (United States)

Patrick, Matthew R.; Anderson, Kyle R.; Poland, Michael P.; Orr, Tim R.; Swanson, Donald A.

2015-01-01

Forecasting volcanic activity relies fundamentally on tracking magma pressure through the use of proxies, such as ground surface deformation and earthquake rates. Lava lakes at open-vent basaltic volcanoes provide a window into the uppermost magma system for gauging reservoir pressure changes more directly. At Kīlauea Volcano (Hawaiʻi, USA) the surface height of the summit lava lake in Halemaʻumaʻu Crater fluctuates with surface deformation over short (hours to days) and long (weeks to months) time scales. This correlation implies that the lake behaves as a simple piezometer of the subsurface magma reservoir. Changes in lava level and summit deformation scale with (and shortly precede) changes in eruption rate from Kīlauea's East Rift Zone, indicating that summit lava level can be used for short-term forecasting of rift zone activity and associated hazards at Kīlauea.

Selfishness Level of Strategic Games

NARCIS (Netherlands)

Apt, K.R.; Schäfer, G.

2014-01-01

We introduce a new measure of the discrepancy in strategic games between the social welfare in a Nash equilibrium and in a social optimum, that we call selfishness level. It is the smallest fraction of the social welfare that needs to be offered to each player to achieve that a social optimum is

Influence of a Large Pillar on the Optimum Roadway Position in an Extremely Close Coal Seam

Directory of Open Access Journals (Sweden)

Li Yang

2016-01-01

Full Text Available Based on the mining practice in an extremely close coal seam, theoretical analysis was conducted on the vertical stress distribution of the floor strata under a large coal pillar. The vertical stress distribution regulation of a No. 5 coal seam was revealed. To obtain the optimum position of the roadway that bears the supporting pressure of a large coal pillar, numerical modeling was applied to analyze the relation among the stress distribution of the roadway surrounding the rock that bears the supporting pressure of a large coal pillar, the plastic zone distribution of the roadway surrounding the rock, the surrounding rock deformation, and the roadway layout position. The theoretical calculation results of the stress value, stress variation rate, and influencing range of the stress influencing angle showed that the reasonable malposition of the No. 5 coal seam roadway was an inner malposition of 4 m. The mining practice showed the following: the layout of No. 25301 panel belt roadway at the position of the inner malposition of 4 m was reasonable, the roadway support performance was favourable without deformation, and ground pressure was not obvious. The research achievement of this study is the provision of a reference for roadway layouts under similar conditions.

Acid pressure leaching of a concentrate containing uranium, thorium and rare earth elements

International Nuclear Information System (INIS)

Lan Xinghua; Peng Ruqing.

1987-01-01

The acid pressure leaching of a concentrate containing rinkolite for recovering uranium, thorium and rare earth elements is described. The laboratory and the pilot plant test results are given. Under the optimum leaching conditions, the recovery of uranium, thorium and rare earth elements are 82.9%, 86.0% and 88.3% respectively. These results show that the acid pressure leaching process is a effective process for treating the concentrate

A Model to Determine the Level of Serum Aldosterone in the Workers Attributed to the Combined Effects of Sound Pressure Level, Exposure Time and Serum Potassium Level: A Field-Based Study

Directory of Open Access Journals (Sweden)

Parvin Nassiri

2016-09-01

Full Text Available Background Occupational exposure to excessive noise is one of the biggest work-related challenges in the world. This phenomenon causes the release of stress-related hormones, which in turn, negatively affects cardiovascular risk factors. Objectives The current study study aimed to determine the level of workers’ serum aldosterone in light of the combined effect of sound pressure level, exposure time and serum potassium level. Methods This cross-sectional, descriptive, analytical study was conducted on 45 workers of Gol-Gohar Mining and Industrial Company in the fall of 2014. The subjects were divided into three groups (one control and two case groups, each including 15 workers. Participants in the control group were selected from workers with administrative jobs (exposure to the background noise. On the other hand, participants in the case groups were selected from the concentrator and pelletizing factories exposed to excessive noise. Serum aldosterone and potassium levels of participants were assessed at three different time intervals: at the beginning of the shift and before exposure to noise (7:30 - 8:00 AM, during exposure to noise (10:00 - 10:30 AM, and during continuous exposure (1:30 - 2:00 PM. The obtained data were transferred into SPSS ver. 18. Repeated measures analysis of variance (ANOVA was used to develop the statistical model of workers’ aldosterone level in light of the combined effect of sound pressure level, exposure time, and serum potassium level. Results The results of the final statistical model to determine the level of serum aldosterone based on the combined effect of sound pressure level, exposure time and serum potassium level indicated that the sound pressure level had a significant influence on the human’s serum aldosterone level (P = 0.04. In addition, the effects of exposure time and serum potassium on aldosterone level were statistically significant with P-values of 0.008 and 0.001, respectively. Conclusions

Optimized ultra-high-pressure-assisted extraction of procyanidins from lychee pericarp improves the antioxidant activity of extracts.

Science.gov (United States)

Zhang, Ruifen; Su, Dongxiao; Hou, Fangli; Liu, Lei; Huang, Fei; Dong, Lihong; Deng, Yuanyuan; Zhang, Yan; Wei, Zhencheng; Zhang, Mingwei

2017-08-01

To establish optimal ultra-high-pressure (UHP)-assisted extraction conditions for procyanidins from lychee pericarp, a response surface analysis method with four factors and three levels was adopted. The optimum conditions were as follows: 295 MPa pressure, 13 min pressure holding time, 16.0 mL/g liquid-to-solid ratio, and 70% ethanol concentration. Compared with conventional ethanol extraction and ultrasonic-assisted extraction methods, the yields of the total procyanidins, flavonoids, and phenolics extracted using the UHP process were significantly increased; consequently, the oxygen radical absorbance capacity and cellular antioxidant activity of UHP-assisted lychee pericarp extracts were substantially enhanced. LC-MS/MS and high-performance liquid chromatography quantification results for individual phenolic compounds revealed that the yield of procyanidin compounds, including epicatechin, procyanidin A2, and procyanidin B2, from lychee pericarp could be significantly improved by the UHP-assisted extraction process. This UHP-assisted extraction process is thus a practical method for the extraction of procyanidins from lychee pericarp.

Uniform and Non-Uniform Optimum Scalar Quantizers Performances: A Comparative Study

Directory of Open Access Journals (Sweden)

Fendy Santoso

2008-05-01

Full Text Available The aim of this research is to investigate source coding, the representation of information source output by finite R bits/symbol. The performance of optimum quantisers subject to an entropy constraint has been studied. The definitive work in this area is best summarised by Shannon’s source coding theorem, that is, a source with entropy H can be encoded with arbitrarily small error probability at any rate R (bits/source output as long as R>H. Conversely, If R the error probability will be driven away from zero, independent of the complexity of the encoder and the decoder employed. In this context, the main objective of engineers is however to design the optimum code. Unfortunately, the rate-distortion theorem does not provide the recipe for such a design. The theorem does, however, provide the theoretical limit so that we know how close we are to the optimum. The full understanding of the theorem also helps in setting the direction to achieve such an optimum. In this research, we have investigated the performances of two practical scalar quantisers, i.e., a Lloyd-Max quantiser and the uniformly defined one and also a well-known entropy coding scheme, i.e., Huffman coding against their theoretically attainable optimum performance due to Shannon’s limit R. It has been shown that our uniformly defined quantiser could demonstrate superior performance. The performance improvements, in fact, are more noticeable at higher bit rates.

Equivalent threshold sound pressure levels for acoustic test signals of short duration

DEFF Research Database (Denmark)

Poulsen, Torben; Daugaard, Carsten

1998-01-01

. The measurements were performed with two types of headphones, Telephonics TDH-39 and Sennheiser HDA-200. The sound pressure levels were measured in an IEC 318 ear simulator with Type 1 adapter (a flat plate) and a conical ring. The audiometric methods used in the experiments were the ascending method (ISO 8253...

A first course in optimum design of yacht sails

Science.gov (United States)

Sugimoto, Takeshi

1993-03-01

The optimum sail geometry is analytically obtained for the case of maximizing the thrust under equality and inequality constraints on the lift and the heeling moment. A single mainsail is assumed to be set close-hauled in uniform wind and upright on the flat sea surface. The governing parameters are the mast height and the gap between the sail foot and the sea surface. The lifting line theory is applied to analyze the aerodynamic forces acting on a sail. The design method consists of the variational principle and a feasibility study. Almost triangular sails are found to be optimum. Their advantages are discussed.

A compact self-recording pressure based sea level gauge suitable for deployments at harbour and offshore environments

Digital Repository Service at National Institute of Oceanography (India)

Desa, E.; Peshwe, V.B.; Joseph, A.; Mehra, P.; Naik, G.P.; Kumar, V.; Desa, E.S.; Desai, R.G.P.; Nagvekar, S.; Desai, S.P.

A compact and lightweight self-recording pressure based sea level gauge has been designed to suit deployments from harbour and offshore environments. A novel hydraulic coupling device designed in-house was used to transfer the seawater pressure...

Assessment of Clostridium perfringens spore response to high hydrostatic pressure and heat with nisin.

Science.gov (United States)

Gao, Yulong; Qiu, Weifen; Wu, Ding; Fu, Qiang

2011-08-01

The elimination of spores from low-acid foods presents food-processing and food-safety challenges to high-pressure processing (HPP) developers as bacterial spores are extremely resistant to pressure. Therefore, the effects of pressure (400-800 MPa), temperature (35-95 °C), and nisin (0-496 IU/mL) on the inactivation of Clostridium perfringens AS 64701 spores at various pressure-holding times (7.5-17.5 min) were explored. A second-order polynomal equation for HPP- and nisin-induced inactivation of C. perfringens spores was constructed with response surface methodology. Experiment results showed that the experimental values were shown to be significantly in agreement with the predicted values because the adjusted determination coefficient (R (Adj)²) was 0.9708 and the level of significance was P pressure of 654 Mpa, temperature of 74 °C, pressure-holding time of 13.6 min, and nisin concentration of 328 IU/mL. The validation of the model equation for predicting the optimum response values was verified effectively by ten test points that were not used in the establishment of the model. Compared with conventional HPP techniques, the main process advantages of HPP-nisin combination sterilization in the UHT milk are, lower pressure, temperature, natural preservative (nisin), and in a shorter treatment time. The synergistic inactivation of bacteria by HPP-nisin combination is a promising and natural method to increase the efficiency and safety of high-pressure pasteurization.

Method for Estimating Optimum Free Resonant Frequencies in Overcoupled WPT System

Directory of Open Access Journals (Sweden)

Dong-Wook Seo

2017-01-01

Full Text Available In our previous work, we proposed the method to maximize the output power even in the overcoupled state of the wireless power transfer (WPT system by controlling free resonant frequencies and derived closed-form expression for optimum free resonant frequencies of the primary and secondary resonators. In this paper, we propose the mutual coupling approach to derive the optimum free resonant frequencies and show the measured power transfer efficiency (PTE using the transmission efficiency as well as the system energy efficiency. The results of the proposed approach exactly coincide with those of the previous work, and the fabricated prototype achieves the transmission efficiency of about 80% by tuning the free resonant frequencies to the optimum values in the overcoupled state.

Calculations enable optimum design of magnetic brake

Science.gov (United States)

Kosmahl, H. G.

1966-01-01

Mathematical analysis and computations determine optimum magnetic coil configurations for a magnetic brake which controllably decelerates a free falling load to a soft stop. Calculations on unconventionally wound coils determine the required parameters for the desired deceleration with minimum electrical energy supplied to the stationary coil.

Sound pressure levels generated at risk volume steps of portable listening devices: types of smartphone and genres of music.

Science.gov (United States)

Kim, Gibbeum; Han, Woojae

2018-05-01

The present study estimated the sound pressure levels of various music genres at the volume steps that contemporary smartphones deliver, because these levels put the listener at potential risk for hearing loss. Using six different smartphones (Galaxy S6, Galaxy Note 3, iPhone 5S, iPhone 6, LG G2, and LG G3), the sound pressure levels for three genres of K-pop music (dance-pop, hip-hop, and pop-ballad) and a Billboard pop chart of assorted genres were measured through an earbud for the first risk volume that was at the risk sign proposed by the smartphones, as well as consecutive higher volumes using a sound level meter and artificial mastoid. The first risk volume step of the Galaxy S6 and the LG G2, among the six smartphones, had the significantly lowest (84.1 dBA) and highest output levels (92.4 dBA), respectively. As the volume step increased, so did the sound pressure levels. The iPhone 6 was loudest (113.1 dBA) at the maximum volume step. Of the music genres, dance-pop showed the highest output level (91.1 dBA) for all smartphones. Within the frequency range of 20~ 20,000 Hz, the sound pressure level peaked at 2000 Hz for all the smartphones. The results showed that the sound pressure levels of either the first volume step or the maximum volume step were not the same for the different smartphone models and genres of music, which means that the risk volume sign and its output levels should be unified across the devices for their users. In addition, the risk volume steps proposed by the latest smartphone models are high enough to cause noise-induced hearing loss if their users habitually listen to music at those levels.

Optimum Replacement Level of the Soybean Meal for Processed ...

African Journals Online (AJOL)

user

KEY WORDS: Processed Horse Eye Bean, Anti-Nutritional Factors, Soaking, Cooking, Broiler Finisher Diet. INTRODUCTION. The protein intake of Nigerians has been on a decline as a result of ever increasing population. The level of animal protein consumption has direct influence on the general well being and health of ...

The theory of an ‘optimum currency area’

Directory of Open Access Journals (Sweden)

Jarosław Kundera

2012-12-01

Full Text Available The main goal of this paper is to analyse and distinguish the main components of the theory of an ‘Optimum Currency Area’. The theory of an optimum currency area indicates some essential elements as preconditions for the successful introduction of a common currency: high mobility of labour, openness of the economy defined as a high proportion of tradable to non-tradable goods, and high diversification of domestic production before joining the union. The article’s analysis helps to better understanding the reasons of the current crisis in the euro zone. The main problem with a common currency area is the adjustment to imbalances, which cannot take place through exchange rates in conditions of a common currency. The missing elements of the theory are the role of the mobility of capital to correct interregional balance of payments disequilibria and lack of a common budget with sufficient own resources during the occurrence of debt crises in member countries. The theory of an optimum currency area has noticed the importance of coordination between fiscal and monetary policy and the necessity of redistribution of resources among partners. However, it does not say much about the methods applied, how to deal with debt crises and what the cost of a potential breaking up of monetary union would be.

Semianalytical and Seminumerical Calculations of Optimum Material Distributions

Energy Technology Data Exchange (ETDEWEB)

Andersson, Gunnar

1963-06-15

Perturbation theory applied to the multigroup diffusion equations gives a general condition for optimum distribution of reactor materials. A certain function of the material densities and the fluxes, here called the W (eight) function, must thus be constant where the variable material density is larger than zero if changes in this density affect only the group constants where the changes occur. The weight function is, however, generally a complicated function and complete solutions have therefore previously been presented only for the special case when constant weight function implies constant thermal flux. It is demonstrated that the condition of constant weight function can be used together with well known methods for numerical solution of the multigroup diffusion equations to obtain optimum material distributions also when the thermal flux varies over the core. Solution of the minimum fuel mass problem for two reflected reactors thus shows that an effective reflector such as D{sub 2}O gives a peak in the optimum fuel distribution at the core-reflector interface, while an ineffective reflector such as a breeder blanket or a steel tank wall 'pushes' the fuel away from the strongly absorbing zone. It is also interesting to compare the effective reflector case with analytically obtained solutions corresponding to flat power density, flat thermal flux and flat fuel density.

Experimental validation of optimum resistance moment of concrete ...

African Journals Online (AJOL)

Experimental validation of optimum resistance moment of concrete slabs reinforced ... other solutions to combat corrosion problems in steel reinforced concrete. ... Eight specimens of two-way spanning slabs reinforced with CFRP bars were ...

Bi-level positive airway pressure ventilation for treating heart failure with central sleep apnea that is unresponsive to continuous positive airway pressure.

Science.gov (United States)

Dohi, Tomotaka; Kasai, Takatoshi; Narui, Koji; Ishiwata, Sugao; Ohno, Minoru; Yamaguchi, Tetsu; Momomura, Shin-Ichi

2008-07-01

Cheyne-Stokes respiration with central sleep apnea (CSR-CSA) is associated with a poor prognosis in patients with heart failure (HF). However, some patients do not respond to continuous positive airway pressure (CPAP), so other therapeutic modalities should be considered, such as bi-level positive airway pressure (PAP), which also assists respiration and might be effective for such patients. The 20 patients with HF because of left ventricular systolic dysfunction were assessed: 8 had ischemic etiology, and all had severe CSA according to the apnea - hypopnea index (AHI) determined by polysomnography. All diagnosed patients underwent repeat polysomnography using CPAP. The AHI improved significantly in 11 (AHI or=15). Bi-level PAP titration significantly improved the AHI in the latter group. Those who were unresponsive to CPAP had significantly lower PaCO(2), higher plasma brain natriuretic peptide (BNP), longer mean duration of CSR and fewer obstructive episodes than CPAP responders. After 6 months of positive airway support with either CPAP (n=9) or bi-level PAP (n=7), BNP levels significantly decreased and left ventricular ejection fraction significantly increased. Bi-level PAP could be an effective alternative for patients with HF and pure CSR-CSA who are unresponsive to CPAP.

Integrated Chassis Control System with Fail Safety Using Optimum Yaw Moment Distribution

International Nuclear Information System (INIS)

Yim, Seongjin

2014-01-01

This paper presents an integrated chassis control system with fail safety using optimum yaw moment distribution for a vehicle with steer-by-wire and brake-by-wire devices. The proposed system has two-level structure: upper- and lower-level controllers. In the upper-level controller, the control yaw moment is computed with sliding mode control theory. In the lower-level controller, the control yaw moment is distributed into the tire forces of active front steering(AFS) and electronic stability control(ESC) with the weighted pseudo-inverse based control allocation(WPCA) method. By setting the variable weights in WPCA, it is possible to take the sensor/actuator failure into account. In this framework, it is necessary to optimize the variables weights in order to enhance the yaw moment distribution. For this purpose, simulation-based tuning is proposed. To show the effectiveness of the proposed method, simulations are conducted on a vehicle simulation package, CarSim

Integrated Chassis Control System with Fail Safety Using Optimum Yaw Moment Distribution

Energy Technology Data Exchange (ETDEWEB)

Yim, Seongjin [Seoul Nat' l Univ. of Sci. and Tech., Seoul (Korea, Republic of)

2014-03-15

This paper presents an integrated chassis control system with fail safety using optimum yaw moment distribution for a vehicle with steer-by-wire and brake-by-wire devices. The proposed system has two-level structure: upper- and lower-level controllers. In the upper-level controller, the control yaw moment is computed with sliding mode control theory. In the lower-level controller, the control yaw moment is distributed into the tire forces of active front steering(AFS) and electronic stability control(ESC) with the weighted pseudo-inverse based control allocation(WPCA) method. By setting the variable weights in WPCA, it is possible to take the sensor/actuator failure into account. In this framework, it is necessary to optimize the variables weights in order to enhance the yaw moment distribution. For this purpose, simulation-based tuning is proposed. To show the effectiveness of the proposed method, simulations are conducted on a vehicle simulation package, CarSim.

The optimum measurement precision evaluation for blood components using near-infrared spectra on 1000-2500 nm

Science.gov (United States)

Zhang, Ziyang; Sun, Di; Han, Tongshuai; Guo, Chao; Liu, Jin

2016-10-01

In the non-invasive blood components measurement using near infrared spectroscopy, the useful signals caused by the concentration variation in the interested components, such as glucose, hemoglobin, albumin etc., are relative weak. Then the signals may be greatly disturbed by a lot of noises in various ways. We improved the signals by using the optimum path-length for the used wavelength to get a maximum variation of transmitted light intensity when the concentration of a component varies. And after the path-length optimization for every wavelength in 1000-2500 nm, we present the detection limits for the components, including glucose, hemoglobin and albumin, when measuring them in a tissue phantom. The evaluated detection limits could be the best reachable precision level since it assumed the measurement uses a high signal-to-noise ratio (SNR) signal and the optimum path-length. From the results, available wavelengths in 1000-2500 nm for the three component measurements can be screened by comparing their detection limit values with their measurement limit requirements. For other blood components measurement, the evaluation their detection limits could also be designed using the method proposed in this paper. Moreover, we use an equation to estimate the absorbance at the optimum path-length for every wavelength in 1000-2500 nm caused by the three components. It could be an easy way to realize the evaluation because adjusting the sample cell's size to the precise path-length value for every wavelength is not necessary. This equation could also be referred to other blood components measurement using the optimum path-length for every used wavelength.

Optimum Combining for Rapidly Fading Channels in Ad Hoc Networks

Directory of Open Access Journals (Sweden)

Sonia Furman

2003-10-01

Full Text Available Research and technology in wireless communication systems such as radar and cellular networks have successfully implemented alternative design approaches that utilize antenna array techniques such as optimum combining, to mitigate the degradation effects of multipath in rapid fading channels. In ad hoc networks, these methods have not yet been exploited primarily due to the complexity inherent in the network's architecture. With the high demand for improved signal link quality, devices configured with omnidirectional antennas can no longer meet the growing need for link quality and spectrum efficiency. This study takes an empirical approach to determine an optimum combining antenna array based on 3 variants of interelement spacing. For rapid fading channels, the simulation results show that the performance in the network of devices retrofitted with our antenna arrays consistently exceeded those with an omnidirectional antenna. Further, with the optimum combiner, the performance increased by over 60% compared to that of an omnidirectional antenna in a rapid fading channel.

An integrated expert system for optimum in core fuel management

International Nuclear Information System (INIS)

Abd Elmoatty, Mona S.; Nagy, M.S.; Aly, Mohamed N.; Shaat, M.K.

2011-01-01

Highlights: → An integrated expert system constructed for optimum in core fuel management. → Brief discussion of the ESOIFM Package modules, inputs and outputs. → Package was applied on the DALAT Nuclear Research Reactor (0.5 MW). → The Package verification showed good agreement. - Abstract: An integrated expert system called Efficient and Safe Optimum In-core Fuel Management (ESOIFM Package) has been constructed to achieve an optimum in core fuel management and automate the process of data analysis. The Package combines the constructed mathematical models with the adopted artificial intelligence techniques. The paper gives a brief discussion of the ESOIFM Package modules, inputs and outputs. The Package was applied on the DALAT Nuclear Research Reactor (0.5 MW). Moreover, the data of DNRR have been used as a case study for testing and evaluation of ESOIFM Package. This paper shows the comparison between the ESOIFM Package burn-up results, the DNRR experimental burn-up data, and other DNRR Codes burn-up results. The results showed good agreement.

Determination of optimum filter in myocardial SPECT: A phantom study

International Nuclear Information System (INIS)

Takavar, A.; Shamsipour, Gh.; Sohrabi, M.; Eftekhari, M.

2004-01-01

Background: In myocardial perfusion SPECT images are degraded by photon attenuation, the distance-dependent collimator, detector response and photons scatter. Filters greatly affect quality of nuclear medicine images. Materials and Methods: A phantom simulating heart left ventricle was built. About 1mCi of 99m Tc was injected into the phantom. Images was taken from this phantom. Some filters including Parzen, Hamming, Hanning, Butter worth and Gaussian were exerted on the phantom images. By defining some criteria such as contrast, signal to noise ratio, and defect size detectability, the best filter can be determined. Results: 0.325 Nyquist frequency and 0.5 nq was obtained as the optimum cut off frequencies respectively for hamming and handing filters. Order 11, cut off 0.45 Nq and order 20 cut off 0.5 Nq obtained optimum respectively for Butter worth and Gaussian filters. Conclusion: The optimum member of every filter's family was obtained

An Investigation of Optimum NLC-Sunscreen Formulation Using Taguchi Analysis

Directory of Open Access Journals (Sweden)

Pao Chi Chen

2013-01-01

Full Text Available This study used three kinds of wax and three kinds of oil, with fixed mixture ratio including UV-blocking materials of ethylhexyl methoxycinnamate, oxybenzone, and avobenzone, and applied hot high-pressure homogenization process to prepare nanolipid sunscreen formulations. The measured particle size of the sunscreen formulations was 100~300 nm around PDI of 0.2 having a moderate polydisperse system. The distribution of zeta potential was −50 mV to −35 mV, showing a stable system. The UV light-absorbing range of 9 groups of sunscreen formulations was 275 nm~380 nm ranging within UVA and UVB. The rheological analysis found that the viscosity change is shear, thinning exhibiting colloid behavior. Taguchi analysis found that the optimum combinations are the carnauba wax and the blackcurrant oil combination for crystallinity and the beeswax and CPG oil for UV absorption. In addition, UV-blocking ability shows that the SPF was 51.5 and PFA was three stars for SU9 formulation. Finally, the effect of temperature on the properties of sunscreen formulations was also explored.

Optimum Temperature and Thermal Stability of Crude Polyphenol ...

African Journals Online (AJOL)

The optimum temperature was found to be 300C for the enzyme extracted from guava, ... processing industries because during the processing ... enhance the brown colour produced (Valero et al., ... considerable economic and nutritional loss.

Intermittent operation of ultra-low pressure ultrafiltration for decentralized drinking water treatment.

Science.gov (United States)

Peter-Varbanets, Maryna; Gujer, Willi; Pronk, Wouter

2012-06-15

River water was treated by ultrafiltration at a relatively low transmembrane pressure (40 mbar). As observed before, flux stabilization occurred after several days of operation although no back-flushing or cross flow was applied. Interruptions in flux were applied by temporary offset of the transmembrane pressure. After restoration of the transmembrane pressure, the initial flux was higher than the stable flux level, and the flux recovery depended on the standstill time. Furthermore, if a short cross flow was applied after standstill, the flux was restored to an even higher level. In all cases, the flux decreased again during operation to reach finally the same stable level as before standstill. In order to evaluate the influence of intermittent operation as practiced for water treatment on a household level, daily interruptions of flux were applied. An optimum of total daily water production rate was obtained at 21 h of operation and 3 h of standstill per day. A model was developed which can describe the impact of intermittent operation on the flux depending on the duration of the standstill and operating periods. This enables the prediction of production capacity of the system operated intermittently. The flux increase during standstill could be explained by a relaxation and expansion of the biofouling layer, while the higher flux after forward-flushing was caused by this layer being partially sloughed off. Household water treatment with the process presented here will generally be operated on a discontinuous basis. The results show that such operation schemes do not compromise the permeability of the system, but actually lead to higher fluxes after standstill. Copyright © 2012 Elsevier Ltd. All rights reserved.

Acute post-stroke blood pressure relative to premorbid levels in intracerebral haemorrhage versus major ischaemic stroke: a population-based study

Science.gov (United States)

Fischer, Urs; Cooney, Marie Therese; Bull, Linda M; Silver, Louise E; Chalmers, John; Anderson, Craig S; Mehta, Ziyah; Rothwell, Peter M

2014-01-01

Summary Background It is often assumed that blood pressure increases acutely after major stroke, resulting in so-called post-stroke hypertension. In view of evidence that the risks and benefits of blood pressure-lowering treatment in acute stroke might differ between patients with major ischaemic stroke and those with primary intracerebral haemorrhage, we compared acute-phase and premorbid blood pressure levels in these two disorders. Methods In a population-based study in Oxfordshire, UK, we recruited all patients presenting with stroke between April 1, 2002, and March 31, 2012. We compared all acute-phase post-event blood pressure readings with premorbid readings from 10-year primary care records in all patients with acute major ischaemic stroke (National Institutes of Health Stroke Scale >3) versus those with acute intracerebral haemorrhage. Findings Of 653 consecutive eligible patients, premorbid and acute-phase blood pressure readings were available for 636 (97%) individuals. Premorbid blood pressure (total readings 13 244) had been measured on a median of 17 separate occasions per patient (IQR 8–31). In patients with ischaemic stroke, the first acute-phase systolic blood pressure was much lower than after intracerebral haemorrhage (158·5 mm Hg [SD 30·1] vs 189·8 mm Hg [38·5], pblood pressure after intracerebral haemorrhage was substantially higher than premorbid levels (mean increase of 40·7 mm Hg, pblood pressure also increased steeply in the days and weeks before intracerebral haemorrhage (regression pblood pressure reading after primary intracerebral haemorrhage was more likely than after ischaemic stroke to be the highest ever recorded (OR 3·4, 95% CI 2·3–5·2, pblood pressure within 3 h of onset was 50 mm Hg higher, on average, than the maximum premorbid level whereas that after ischaemic stroke was 5·2 mm Hg lower (pblood pressure is substantially raised compared with usual premorbid levels after intracerebral haemorrhage, whereas acute

ANALYSIS OF SOUND PRESSURE LEVEL (SPL AND LAY OUT OF ENGINES IN THE FACTORY

Directory of Open Access Journals (Sweden)

Wijianto Wijianto

2017-01-01

Full Text Available Modeling layout of engines in the factory is very useful to know how many dB sound pressure level that are occur in the building in order to avoid hearing damage of employees that are caused by noise. The objective of this research is to know how many dB sound pressure level that are occur in the factory with engine composition such as boiler, diesel, turbine, motor and gear box with dimension of building are 40 m length, 35 m width and 10 m height. With MATLAB analysis can be obtain that the highest SPL is 104.7 dB and the lowest is 93.5 dB, so, this range are dangerous for human hearing. To avoid hearing damage in this area, employees must use hearing protector.

Optimum sample size to estimate mean parasite abundance in fish parasite surveys

Directory of Open Access Journals (Sweden)

Shvydka S.

2018-03-01

Full Text Available To reach ethically and scientifically valid mean abundance values in parasitological and epidemiological studies this paper considers analytic and simulation approaches for sample size determination. The sample size estimation was carried out by applying mathematical formula with predetermined precision level and parameter of the negative binomial distribution estimated from the empirical data. A simulation approach to optimum sample size determination aimed at the estimation of true value of the mean abundance and its confidence interval (CI was based on the Bag of Little Bootstraps (BLB. The abundance of two species of monogenean parasites Ligophorus cephali and L. mediterraneus from Mugil cephalus across the Azov-Black Seas localities were subjected to the analysis. The dispersion pattern of both helminth species could be characterized as a highly aggregated distribution with the variance being substantially larger than the mean abundance. The holistic approach applied here offers a wide range of appropriate methods in searching for the optimum sample size and the understanding about the expected precision level of the mean. Given the superior performance of the BLB relative to formulae with its few assumptions, the bootstrap procedure is the preferred method. Two important assessments were performed in the present study: i based on CIs width a reasonable precision level for the mean abundance in parasitological surveys of Ligophorus spp. could be chosen between 0.8 and 0.5 with 1.6 and 1x mean of the CIs width, and ii the sample size equal 80 or more host individuals allows accurate and precise estimation of mean abundance. Meanwhile for the host sample size in range between 25 and 40 individuals, the median estimates showed minimal bias but the sampling distribution skewed to the low values; a sample size of 10 host individuals yielded to unreliable estimates.

Evaluation of Optimum Moisture Content for Composting of Beef Manure and Bedding Material Mixtures Using Oxygen Uptake Measurement

OpenAIRE

Eunjong Kim; Dong-Hyun Lee; Seunggun Won; Heekwon Ahn

2016-01-01

Moisture content influences physiological characteristics of microbes and physical structure of solid matrices during composting of animal manure. If moisture content is maintained at a proper level, aerobic microorganisms show more active oxygen consumption during composting due to increased microbial activity. In this study, optimum moisture levels for composting of two bedding materials (sawdust, rice hull) and two different mixtures of bedding and beef manure (BS, Beef cattle manure+sawdu...

A Lateral Differential Resonant Pressure Microsensor Based on SOI-Glass Wafer-Level Vacuum Packaging

Directory of Open Access Journals (Sweden)

Bo Xie

2015-09-01

Full Text Available This paper presents the fabrication and characterization of a resonant pressure microsensor based on SOI-glass wafer-level vacuum packaging. The SOI-based pressure microsensor consists of a pressure-sensitive diaphragm at the handle layer and two lateral resonators (electrostatic excitation and capacitive detection on the device layer as a differential setup. The resonators were vacuum packaged with a glass cap using anodic bonding and the wire interconnection was realized using a mask-free electrochemical etching approach by selectively patterning an Au film on highly topographic surfaces. The fabricated resonant pressure microsensor with dual resonators was characterized in a systematic manner, producing a quality factor higher than 10,000 (~6 months, a sensitivity of about 166 Hz/kPa and a reduced nonlinear error of 0.033% F.S. Based on the differential output, the sensitivity was increased to two times and the temperature-caused frequency drift was decreased to 25%.

Study on optimum aseismic design of complex structure system focusing on damping effect

International Nuclear Information System (INIS)

Takahashi, Yoshitaka; Suzuki, Kohei

1995-01-01

Optimum design technique for the purpose of aseismic design of complex plant structures such as piping and boiler structures is proposed. Particular attention is focused on the evaluation of the optimum damping and stiffness of the structures and components. Pseudo least square algorithm is introduced to determine the optimum design parameters. Under the requirement of certain allowable maximum response to a given earthquake excitation, optimum stiffness and damping values of the structure can be simultaneously calculated by this proposed method. The applicability of the method is demonstrated through three structural models; (1) linear multi-storied building model in which stiffness and damping constant of each floor are optimized; (2) nonlinear multi-storied building model having the isolated floor in which hysteretic energy absorber of the isolator is optimized; (3) combined boiler-supporting structure model connected by the inelastic seismic ties with each other is optimized. In this model, optimum values of damping characteristic of the seismic ties are evaluated. This work is particularly important for the aseismic design of complex plant structures like integrated boiler-supporting structure in thermal power plant and piping-containment vessel structure in nuclear power plant

Evaluation of the effects of various sound pressure levels on the level of serum aldosterone concentration in rats

Directory of Open Access Journals (Sweden)

Parvin Nassiri

2017-01-01

Full Text Available Introduction: Noise exposure may have anatomical, nonauditory, and auditory influences. Considering nonauditory impacts, noise exposure can cause alterations in the automatic nervous system, including increased pulse rates, heightened blood pressure, and abnormal secretion of hormones. The present study aimed at examining the effect of various sound pressure levels (SPLs on the serum aldosterone level among rats. Materials and Methods: A total of 45 adult male rats with an age range of 3 to 4 months and a weight of 200 ± 50 g were randomly divided into 15 groups of three. Three groups were considered as the control groups and the rest (i.e., 12 groups as the case groups. Rats of the case groups were exposed to SPLs of 85, 95, and 105 dBA. White noise was used as the noise to which the rats were exposed. To measure the level of rats’ serum aldosterone, 3 mL of each rat’s sample blood was directly taken from the heart of anesthetized animals by using syringes. The taken blood samples were put in labeled test tubes that contained anticoagulant Ethylenediaminetetraacetic acid. In the laboratory, the level of aldosterone was assessed through Enzyme-linked immunosorbent assay protocol. The collected data were analyzed by the use of Statistical Package for Social Sciences (SPSS version 18. Results: The results revealed that there was no significant change in the level of rats’ serum aldosterone as a result of exposure to SPLs of 65, 85, and 95 dBA. However, the level of serum aldosterone experienced a remarkable increase after exposure to the SPL of 105 dBA (P < 0.001. Thus, the SPL had a significant impact on the serum aldosterone level (P < 0.001. In contrast, the exposure time and the level of potassium in the used water did not have any measurable influence on the level of serum aldosterone (P = 0.25 and 0.39. Conclusion: The findings of this study demonstrated that serum aldosterone can be used as a biomarker in the face of sound

Method of selecting optimum cross arm lengths for a 750 kV transmission line

Energy Technology Data Exchange (ETDEWEB)

Aleksandrov, G N; Olorokov, V P

1965-01-01

A method is presented, based on both technical and economic considerations, for selecting cross arm lengths for intermediate poles of power transmission lines according to the effects of internal overvoltage, methods from probability theory and mathematical statistics employed. The problem of optimum pole size is considered in terms of the effect of internal overvoltages for a prescribed maximum level of 2.1 PU currently used in the USSR for the design of 750 kV lines.

Common Core: Teaching Optimum Topic Exploration (TOTE)

Science.gov (United States)

Karge, Belinda Dunnick; Moore, Roxane Kushner

2015-01-01

The Common Core has become a household term and yet many educators do not understand what it means. This article explains the historical perspectives of the Common Core and gives guidance to teachers in application of Teaching Optimum Topic Exploration (TOTE) necessary for full implementation of the Common Core State Standards. An effective…

Optimum thermal sizing and operating conditions for once through steam generator

Energy Technology Data Exchange (ETDEWEB)

Yi, Kunwoo; Ju, Kyongin; Im, Inyoung; Kim, Eunkee [KEPCO Engineering and Construction Company., Inc., Daejeon (Korea, Republic of)

2014-10-15

The steam generator is designed to be optimized so as to remove heat and to produce steam vapor. Because of its importance, theoretical and experimental researches have been performed on forced convection boiling heat transfer. The purpose of this study is to predict the thermal behavior and to perform optimum thermal sizing of once through steam generator. To estimate the tube thermal sizing and operating conditions of the steam generator, the analytical modeling is employed on the basis of the empirical correlation equations and theory. The optimized algorithm model, Non-dominated Sorting Genetic Algorithm (NSGA)-II, uses for this analysis. This research is focused on the design of in-vessel steam generator. An one dimensional analysis code is developed to evaluate previous researches and to optimize steam generator design parameters. The results of one-dimensional analysis need to be verified with experimental data. Goals of multi-objective optimization are to minimize tube length, pressure drop and tube number. Feedwater flow rate up to 115.425kg/s is selected so as to have margin of feedwater temperature 20 ..deg. C. For the design of 200MWth once through steam generator, it is evaluated that the tube length shall be over 12.0m for the number of tubes, 2500ea, and the length of the tube shall be over 8.0m for the number of tubes, 4500ea. The parallel coordinates chart can be provided to determine the optimal combination of number of tube, pressure drop, tube diameter and length.

Pressure sound level measurements at an educational environment in Goiânia, Goiás, Brazil

Science.gov (United States)

Costa, J. J. L.; do Nascimento, E. O.; de Oliveira, L. N.; Caldas, L. V. E.

2018-03-01

In this work, 25 points located on the ground floor of the Federal Institute of Education, Science and Technology of Goias - IFG - Campus Goiânia, were analyzed in morning periods of two Saturdays. The pressure sound levels were measured at internal and external environments during routine activities seeking to perform an environmental monitoring at this institution. The initial hypothesis was that an amusement park (Mutirama Park) was responsible for originating noise pollution in the institute, but the results showed, within the campus environment, sound pressure levels in accordance with the Municipal legislation of Goiânia for all points.

Optimum heat power cycles for specified boundary conditions

International Nuclear Information System (INIS)

Ibrahim, O.M.; Klein, S.A.; Mitchell, J.W.

1991-01-01

In this paper optimization of the power output of Carnot and closed Brayton cycles is considered for both finite and infinite thermal capacitance rates of the external fluid streams. The method of Lagrange multipliers is used to solve for working fluid temperatures that yield maximum power. Analytical expressions for the maximum power and the cycle efficiency at maximum power are obtained. A comparison of the maximum power from the two cycles for the same boundary conditions, i.e., the same heat source/sink inlet temperatures, thermal capacitance rates, and heat exchanger conductances, shows that the Brayton cycle can produce more power than the Carnot cycle. This comparison illustrates that cycles exist that can produce more power than the Carnot cycle. The optimum heat power cycle, which will provide the upper limit of power obtained from any thermodynamic cycle for specified boundary conditions and heat exchanger conductances is considered. The optimum heat power cycle is identified by optimizing the sum of the power output from a sequence of Carnot cycles. The shape of the optimum heat power cycle, the power output, and corresponding efficiency are presented. The efficiency at maximum power of all cycles investigated in this study is found to be equal to (or well approximated by) η = 1 - sq. root T L.in /φT H.in where φ is a factor relating the entropy changes during heat rejection and heat addition

An optimum silica flour-bentonite mixture for an engineered barrier

International Nuclear Information System (INIS)

Walker, J.N.; Daffern, D.D.; Emer, D.F.

1991-01-01

To dispose of low-level and mixed wastes (MAR) by burial, it is necessary to design an impermeable closure, which limits water infiltration through the waste. Bentonite has very low permeability to water but can be subject to volume alterations. Over time, these alterations can lead to channeling and subsequent permeability increases. The fluid conductivity and bulk properties of silica flour and bentonite mixtures were tested to find a mixture that would retain the low conductivity of the bentonite while maintaining volumetric stability. Silica flour was chosen for its small grain size and spherical shape, and its similarity to silty soil. Test results indicate that a 90% silica flour and 10% bentonite mixture will provide the optimum properties for this application. 5 refs., 2 figs., 2 tabs

An optimum organizational structure for a large earth-orbiting multidisciplinary Space Base

Science.gov (United States)

Ragusa, J. M.

1973-01-01

The purpose of this exploratory study was to identify an optimum hypothetical organizational structure for a large earth-orbiting multidisciplinary research and applications (R&A) Space Base manned by a mixed crew of technologists. Since such a facility does not presently exist, in situ empirical testing was not possible. Study activity was, therefore, concerned with the identification of a desired organizational structural model rather than the empirical testing of it. The essential finding of this research was that a four-level project type 'total matrix' model will optimize the efficiency and effectiveness of Space Base technologists.

The Prospects of Creating an Optimum Currency Area among Asean Countries

Directory of Open Access Journals (Sweden)

Yana Valeryevna Dyomina

2016-03-01

Full Text Available The article assesses the prospects of creating an optimum currency area (OCA among ASEAN countries. To ensure sustainability of the creating currency zone, the potential candidate countries should meet the criteria of the OCA theory. At the same time, the present technique of assessing candidate countries implies that they must meet the OCA criteria relative to the «anchor» country. This approach creates the problem of the sensitivity of calculation results to the choice of the anchor country. Thus, the case of the OCA composition with Indonesia as the anchor country is different from the one with Singapore as the anchor country. Author’s modification of the specified technique allows bypassing the mentioned problem. Applying the modified approach to the ASEAN member countries allows concluding that the creation of an optimum currency area in South-East Asia is economically feasible for Singapore, Vietnam, Indonesia, Malaysia, Philippines, Brunei Darussalam and Thailand. The rest of the ASEAN member countries (Cambodia, Lao PDR and Myanmar have not yet reached a high degree of macroeconomic convergence with partners of the integration bloc and even among themselves. Therefore there is a need for a transition period, during which the economies of these three countries can «catch up» the level of the more developed ASEAN member countries

On the optimum area-balanced filters for nuclear spectroscopy

International Nuclear Information System (INIS)

Ripamonti, G.; Pullia, A.

1996-01-01

The minimum noise area-balanced (A-B) filters for nuclear spectroscopy are disentangled in the sum of two optimized individual filters. The former is the unipolar finite cusp filter, used for pulse amplitude estimation but affected by baseline shift errors, the latter is a specific filter used for baseline estimation. Each of them is optimized so as to give the minimum noise in the estimation of the pulse amplitude or of its baseline level. It is shown that double optimisation produces an overall optimum filter exhibiting a total noise V 2 n equal to the sum of the noises V 2 n1 and V 2 n2 exhibited by each filter individually. This is a consequence of the orthogonality of the individual filter weight-functions in a function space where the norm is defined as √(V 2 n ). (orig.)

Determination of Optimum Condition of Leucine Content in Beef Protein Hydrolysate using Response Surface Methodology

International Nuclear Information System (INIS)

Siti Roha Ab Mutalib; Zainal Samicho; Noriham Abdullah

2016-01-01

The aim of this study is to determine the optimum condition of leucine content in beef hydrolysate. Beef hydrolysate was prepared by enzymatic hydrolysis using bromelain enzyme produced from pineapple peel. Parameter conditions such as concentration of bromelain, hydrolysis temperature and hydrolysis time were assessed to obtain the optimum leucine content of beef hydrolysate according to experimental design which was recommended by response surface methodology (RSM). Leucine content in beef hydrolysate was determined using AccQ. Tag amino acid analysis method using high performance liquid chromatography (HPLC). The condition of optimum leucine content was at bromelain concentration of 1.38 %, hydrolysis temperature of 42.5 degree Celcius and hydrolysis time of 31.59 hours with the predicted leucine content of 26.57 %. The optimum condition was verified with the leucine value obtained was 26.25 %. Since there was no significant difference (p>0.05) between the predicted and verified leucine values, thus it indicates that the predicted optimum condition by RSM can be accepted to predict the optimum leucine content in beef hydrolysate. (author)

Determination of the Optimum Thickness of Approximately ...

African Journals Online (AJOL)

In an attempt to conserve the world's scarce energy and material resources, a balance between the cost of heating a material and the optimum thickness of the material becomes vey essential. One of such materials is the local cast aluminium pot commonly used as cooking ware in Nigeria. This paper therefore sets up a ...

Process and device for measuring the level in a reactor pressure vessel of a boiling water reactor

International Nuclear Information System (INIS)

Walleser, A.

1987-01-01

The differential pressure is measured between the lower space filled with liquid and a comparison column which is connected to the upper part space filled with steam. From this measurement and the liquid and steam densities in the pressure vessel and in the comparison column and the effects of flow at the pressure sampling positions, the level is determined in an evaluation unit. To determine the densities of liquids and steam, the reactor pressure or the change of pressure with time for transient processes is measured. The density of the comparison column is determined by temperature measurement. The effects of flow are determined by flow measurements. All the measurements are taken to an evaluation unit. (orig./HP) [de

FEM analysis of foundation raft for 500 MWe pressurized heavy water reactor building

International Nuclear Information System (INIS)

Kulkarni, N.N.; Goray, J.S.; Joshi, M.H.; Paramasivam, V.

1989-01-01

Foundation raft supports the containment structure and internals for 500 MWe PHW reactor building. It also serves as bottom envelop of the containment structure. In view of this, the design of foundation raft assumes great importance. The foundation raft is subjected to various load, most significant of them are dead load of structure, equipment loads transferred through a system of floors, walls and structural steel columns, pressure load during accident conditions, seismic loads, earth pressure, uplift due to buoyancy loads, foundation reaction etc. In order to achieve optimum design, the detailed structural analysis is required to be performed methodically and in most realistic manner. Finite element methods which have come in vogue with the developments in digital computers can be successfully applied in this area. The paper describes the above methods in detail for the analysis of foundation raft for the various load combinations required to be considered for safe and optimum design

A novel approach for optimum allocation of FACTS devices using multi-objective function

International Nuclear Information System (INIS)

Gitizadeh, M.; Kalantar, M.

2009-01-01

This paper presents a novel approach to find optimum type, location, and capacity of flexible alternating current transmission systems (FACTS) devices in a power system using a multi-objective optimization function. Thyristor controlled series compensator (TCSC) and static var compensator (SVC) are utilized to achieve these objectives: active power loss reduction, new introduced FACTS devices cost reduction, increase the robustness of the security margin against voltage collapse, and voltage deviation reduction. The operational and controlling constraints as well as load constraints are considered in the optimum allocation procedure. Here, a goal attainment method based on simulated annealing is used to approach the global optimum. In addition, the estimated annual load profile has been utilized to the optimum siting and sizing of FACTS devices to approach a practical solution. The standard IEEE 14-bus test system is used to validate the performance and effectiveness of the proposed method

Evaluation of the Validity and Reliability of the Waterlow Pressure Ulcer Risk Assessment Scale.

Science.gov (United States)

Charalambous, Charalambos; Koulori, Agoritsa; Vasilopoulos, Aristidis; Roupa, Zoe

2018-04-01

Prevention is the ideal strategy to tackle the problem of pressure ulcers. Pressure ulcer risk assessment scales are one of the most pivotal measures applied to tackle the problem, much criticisms has been developed regarding the validity and reliability of these scales. To investigate the validity and reliability of the Waterlow pressure ulcer risk assessment scale. The methodology used is a narrative literature review, the bibliography was reviewed through Cinahl, Pubmed, EBSCO, Medline and Google scholar, 26 scientific articles where identified. The articles where chosen due to their direct correlation with the objective under study and their scientific relevance. The construct and face validity of the Waterlow appears adequate, but with regards to content validity changes in the category age and gender can be beneficial. The concurrent validity cannot be assessed. The predictive validity of the Waterlow is characterized by high specificity and low sensitivity. The inter-rater reliability has been demonstrated to be inadequate, this may be due to lack of clear definitions within the categories and differentiating level of knowledge between the users. Due to the limitations presented regarding the validity and reliability of the Waterlow pressure ulcer risk assessment scale, the scale should be used in conjunction with clinical assessment to provide optimum results.

Evaluation of the Validity and Reliability of the Waterlow Pressure Ulcer Risk Assessment Scale

Science.gov (United States)

Charalambous, Charalambos; Koulori, Agoritsa; Vasilopoulos, Aristidis; Roupa, Zoe

2018-01-01

Introduction Prevention is the ideal strategy to tackle the problem of pressure ulcers. Pressure ulcer risk assessment scales are one of the most pivotal measures applied to tackle the problem, much criticisms has been developed regarding the validity and reliability of these scales. Objective To investigate the validity and reliability of the Waterlow pressure ulcer risk assessment scale. Method The methodology used is a narrative literature review, the bibliography was reviewed through Cinahl, Pubmed, EBSCO, Medline and Google scholar, 26 scientific articles where identified. The articles where chosen due to their direct correlation with the objective under study and their scientific relevance. Results The construct and face validity of the Waterlow appears adequate, but with regards to content validity changes in the category age and gender can be beneficial. The concurrent validity cannot be assessed. The predictive validity of the Waterlow is characterized by high specificity and low sensitivity. The inter-rater reliability has been demonstrated to be inadequate, this may be due to lack of clear definitions within the categories and differentiating level of knowledge between the users. Conclusion Due to the limitations presented regarding the validity and reliability of the Waterlow pressure ulcer risk assessment scale, the scale should be used in conjunction with clinical assessment to provide optimum results. PMID:29736104

Experiments on the spray nozzles used in the pressurizer of power reactor

International Nuclear Information System (INIS)

Diao Wentang

1989-04-01

The spray nozzle, which is used in the pressurizer of pressurized water reactor system, usually uses a less differential pressure between the reactor inlet and outlet as the spray drive pressure, but its flow rate is relatively larger. It is difficult to obtain a optimum spray performance of such a nozzle. The experimental results of five types of twenty seven spray nozzles in different structures and sizes with the range of the spray drive pressure from 0.127 to 0.245 MPa and the flow rates from 5 to 50 t/h are given. The main factors affecting spray performances and their distribution characteristics have been found. And some relatively suitable spray structures have been recommended, which can be used as references for improving the spray nozzles used in the pressurizers of existing PWRs or of the PWRs to be built

Universal Curve of Optimum Thermoelectric Figures of Merit for Bulk and Low-Dimensional Semiconductors

Science.gov (United States)

Hung, Nguyen T.; Nugraha, Ahmad R. T.; Saito, Riichiro

2018-02-01

This paper is a contribution to the Physical Review Applied collection in memory of Mildred S. Dresselhaus. Analytical formulas for thermoelectric figures of merit and power factors are derived based on the one-band model. We find that there is a direct relationship between the optimum figures of merit and the optimum power factors of semiconductors despite of the fact that the two quantities are generally given by different values of chemical potentials. By introducing a dimensionless parameter consisting of the optimum power factor and lattice thermal conductivity (without electronic thermal conductivity), it is possible to unify optimum figures of merit of both bulk and low-dimensional semiconductors into a single universal curve that covers many materials with different dimensionalities.

Genotype x environment interaction and optimum resource ...

African Journals Online (AJOL)

... x E) interaction and to determine the optimum resource allocation for cassava yield trials. The effects of environment, genotype and G x E interaction were highly significant for all yield traits. Variations due to G x E interaction were greater than those due to genotypic differences for all yield traits. Genotype x location x year ...

OPTIMUM VOLUME OF BANK RESERVE: FORECASTING OF OVERDUE CREDIT INDEBTEDNESS USING COPULA MODELS

Directory of Open Access Journals (Sweden)

Kazakova K. A.

2015-12-01

Full Text Available The article propose to consider the possibility of RLUF-copulas application for the creation of joint distributions of overdue credit indebtedness ranks with macroeconomic indicators for the purpose of indebtedness forecasting and also for the definition of optimum volumes of reserve requirements for the corresponding losses. In this research the comparative analysis of multivariate distributions of RLUF-copula estimation with such classical copulas, as FGM-copula, Frank's copula and Gauss's copula is made. In the article the method of maximum likelihood is used for receiving estimates of model parameters. In case of RLUF-copula Bayesian estimates of parameters are received using the Metropolis algorithm with random volatility. Forecasting of bank reserve volumes for all received models is executed in the form of random sample generation by the means of the algorithm of acceptance-deviation for the creation of the corresponding sample of joint distribution using the copula density function. As the result of playing of hundred possible scenarios of indebtedness volumes is obtained the 95 % confidence level for the possible volume of credit indebtedness which can fully act as the optimum volume of reserve requirements for the corresponding credit losses.

Optimum electron temperature and density for short-wavelength plasma-lasing from nickel-like ions

International Nuclear Information System (INIS)

Masoudnia, Leili; Bleiner, Davide

2014-01-01

Soft X-ray lasing across a Ni-like plasma gain-medium requires optimum electron temperature and density for attaining to the Ni-like ion stage and for population inversion in the 3d 9 4d 1 (J=0)→3d 9 4p 1 (J=1) laser transition. Various scaling laws, function of operating parameters, were compared with respect to their predictions for optimum temperatures and densities. It is shown that the widely adopted local thermodynamic equilibrium (LTE) model underestimates the optimum plasma-lasing conditions. On the other hand, non-LTE models, especially when complemented with dielectronic recombination, provided accurate prediction of the optimum plasma-lasing conditions. It is further shown that, for targets with Z equal or greater than the rare-earth elements (e.g. Sm), the optimum electron density for plasma-lasing is not accessible for pump-pulses at λ=1ω=1μm. This observation explains a fundamental difficulty in saturating the wavelength of plasma-based X-ray lasers below 6.8 nm, unless using 2ω pumping

Deuterium–tritium catalytic reaction in fast ignition: Optimum ...

Indian Academy of Sciences (India)

proton beam, the corresponding optimum interval values are proton average energy 3 ... contributions, into the study of the ignition and burn dynamics in a fast ignition frame- ..... choice of proton beam energy would fall in 3 ≤ Ep ≤ 10 MeV.

Radiographic testing - optimum radiographs of plastics and composite materials with dosimeter control

International Nuclear Information System (INIS)

Kuster, J.

1978-01-01

In view of great differencies in X-ray transmission it is more difficult to get optimum radiographs of plastics and especially of reinforced plastics than for example of metals. A procedure will be reported how to get with little effort optimum radiographs especially also in the range of long wavelength radiation corresponding 10 to 25 kV.P. (orig.) [de

Relationship between intracranial pressure and antifungal agents levels in the CSF of patients with cryptococcal meningitis.

Science.gov (United States)

Wirth, Fernanda; de Azevedo, Maria Isabel; Pilla, Carmen; Aquino, Valério Rodrigues; Neto, Gustavo Wissmann; Goldani, Luciano Zubaran

2018-04-01

The purpose of this study was to evaluate the influence of intracranial hypertension in the cerebrospinal fluid (CSF) levels of amphotericin B and fluconazole levels of patients with cryptococcal meningitis. CSF samples and intracranial pressure were obtained by means of routine punctures performed at days 1, 7, and 14 of therapy, respectively. Amphotericin B and fluconazole CSF levels were measured by HPLC method as previously described. The minimum inhibitory concentration for amphotericin B, fluconazole, 5΄flucytosine, and voriconazole of each Cryptococcus isolate was performed according to CLSI. The predominant Cryptococcus species found was C. neoformans, and the major underlying condition was AIDS. Only one CSF sample had a detectable level for amphotericin B during the 14 days of therapy. Fluconazole CSF levels progressively increased from day 1 to day 14 of therapy for most cases. Fluconazole levels in the CSF were above the minimum inhibitory concentrations (MICs) for Cryptococcus during the initial 14 days of antifungal therapy. Variations of intracranial pressure did not affect amphotericin B and fluconazole levels in the CSF. The generalized estimating correlation (GEE) and Spearman correlation test (SCT) showed no significant correlation between the amphotericin B or fluconazole concentrations in the CSF and intracranial pressure (P = .953 and P = .093, respectively for GEE test and P = .477 and P = .847, respectively, for SCT). Combination therapy of amphotericin B with fluconazole was effective in 60% of the patients considering CSF cultures were negative in 9 of 15 patients after 14 days of therapy. Further studies are necessary to evaluate the role of intracranial hypertension on the therapeutic efficacy of different antifungal agents in patients with cryptococcal meningitis.

An optimum design of R-C oscillatory De-Qing circuit

International Nuclear Information System (INIS)

Cao Dezhang; Pan Linghe; Yang Tianlu

1990-01-01

An optimum design of R-C oscillatory De-Qing circuit has been developed for voltage regulation of the pulse modulator. When a new coefficient T 3 /T is introduced, the selection of De-Qing circuit parameters will become quite simple and the optimum parameters can be calculated directly. The De-Qing circuit parameters calculated will be effective in the whole range of the percentage regulation η from zero to maximum design value. The limit value of η is 0.36 or 0.29, theoretically, when the time constant of the De-Qing circuit is 3RC or 5RC respectively

Determination of optimum oven cooking procedures for lean beef products

OpenAIRE

Rodas?Gonz?lez, Argenis; Larsen, Ivy L.; Uttaro, Bethany; Ju?rez, Manuel; Parslow, Joyce; Aalhus, Jennifer L.

2015-01-01

Abstract In order to determine optimum oven cooking procedures for lean beef, the effects of searing at 232 or 260?C for 0, 10, 20 or 30?min, and roasting at 160 or 135?C on semimembranosus (SM) and longissimus lumborum (LL) muscles were evaluated. In addition, the optimum determined cooking method (oven?seared for 10?min at 232?C and roasted at 135?C) was applied to SM roasts varying in weight from 0.5 to 2.5?kg. Mainly, SM muscles seared for 0 or 10?min at 232?C followed by roast at 135?C h...

Simulation of optimum parameters for GaN MSM UV photodetector

Energy Technology Data Exchange (ETDEWEB)

Alhelfi, Mohanad A., E-mail: mhad12344@gmail.com; Ahmed, Naser M., E-mail: nas-tiji@yahoo.com; Hashim, M. R., E-mail: roslan@usm.my; Hassan, Z., E-mail: zai@usm.my [Institue of Nano-Optoelectronics Research and Technology (INOR), School of Physics, Universiti Sains Malaysia 11800 Penang (Malaysia); Al-Rawi, Ali Amer, E-mail: aliamer@unimap.edu.my [School of Computer and Communication Eng. 3st Floor, Pauh Putra Main Campus 02600 Arau, Perlis Malaysia (Malaysia)

2016-07-06

In this study the optimum parameters of GaN M-S-M photodetector are discussed. The evaluation of the photodetector depends on many parameters, the most of the important parameters the quality of the GaN film and others depend on the geometry of the interdigited electrode. In this simulation work using MATLAB software with consideration of the reflection and absorption on the metal contacts, a detailed study involving various electrode spacings (S) and widths (W) reveals conclusive results in device design. The optimum interelectrode design for interdigitated MSM-PD has been specified and evaluated by effect on quantum efficiency and responsivity.

Levels of amyloid-beta-42 and CSF pressure are directly related in patients with Alzheimer's disease.

Science.gov (United States)

Schirinzi, Tommaso; Di Lazzaro, Giulia; Sancesario, Giulia Maria; Colona, Vito Luigi; Scaricamazza, Eugenia; Mercuri, Nicola Biagio; Martorana, Alessandro; Sancesario, Giuseppe

2017-12-01

Experimental data suggest that the cerebrospinal fluid (CSF) dynamic is involved in the clearance of beta-amyloid, a key event in the pathogenesis of Alzheimer's disease (AD). At this regard no evidence still exists in vivo. In this study we explored the relationships between CSF pressure and AD pathology, as measured with CSF core biomarkers. We enrolled 16 patients with probable AD and 21 controls, collecting demographics, clinical data, CSF opening pressure and CSF levels of beta-amyloid-42 fragment (Aβ42), total-tau (t-tau), phosphorylated-tau-181 (p-tau), albumin and albumin ratio. Differences between the groups were calculated with non-parametric tests, while correlations among all parameters were separately calculated with Spearman's test in each group. The groups significantly differed in biomarkers' concentration with lower Aβ42, and higher t-tau and p-tau in AD patients. Moreover, CSF pressure was significantly lower in AD group (11.0 ± 2.8 vs. 13.3 ± 3.0 mmHg, p < 0.05) and directly correlated with Aβ42 levels (R = 0.512; p < 0.05), but not with other biomarkers or parameters. No significant correlations emerged for biomarkers in control group. AD patients exhibit low CSF pressure whose values are directly and selectively related to CSF Aβ42 levels. This interesting correlation may confirm in vivo the association between CSF dynamic and beta-amyloid metabolism occurring in AD.

Optimization of hydrostatic pressure at varied sonication conditions--power density, intensity, very low frequency--for isothermal ultrasonic sludge treatment.

Science.gov (United States)

Delmas, Henri; Le, Ngoc Tuan; Barthe, Laurie; Julcour-Lebigue, Carine

2015-07-01

This work aims at investigating for the first time the key sonication (US) parameters: power density (DUS), intensity (IUS), and frequency (FS) - down to audible range, under varied hydrostatic pressure (Ph) and low temperature isothermal conditions (to avoid any thermal effect). The selected application was activated sludge disintegration, a major industrial US process. For a rational approach all comparisons were made at same specific energy input (ES, US energy per solid weight) which is also the relevant economic criterion. The decoupling of power density and intensity was obtained by either changing the sludge volume or most often by changing probe diameter, all other characteristics being unchanged. Comprehensive results were obtained by varying the hydrostatic pressure at given power density and intensity. In all cases marked maxima of sludge disintegration appeared at optimum pressures, which values increased at increasing power intensity and density. Such optimum was expected due to opposite effects of increasing hydrostatic pressure: higher cavitation threshold then smaller and fewer bubbles, but higher temperature and pressure at the end of collapse. In addition the first attempt to lower US frequency down to audible range was very successful: at any operation condition (DUS, IUS, Ph, sludge concentration and type) higher sludge disintegration was obtained at 12 kHz than at 20 kHz. The same values of optimum pressure were observed at 12 and 20 kHz. At same energy consumption the best conditions - obtained at 12 kHz, maximum power density 720 W/L and 3.25 bar - provided about 100% improvement with respect to usual conditions (1 bar, 20 kHz). Important energy savings and equipment size reduction may then be expected. Copyright © 2014 Elsevier B.V. All rights reserved.

The concentration of optimum dissolved oxygen levels for growth of mangrove crab Scylla serrata seed in recirculation system

Directory of Open Access Journals (Sweden)

Kurnia Faturrohman

2017-07-01

Full Text Available ABSTRACT This study aimed to determine optimum dissolved oxygen (DO through the addition of aeration and to evaluate the role of dissolved oxygen on production performance and stress responses of mangrove crab Scylla serrata. Experimental design used was complete randomized design with four treatments namely no aeration (A, one point aeration (B, two points aeration (C, and three points aeration (D. All treatments replicated three times. The crab with the average of body weight 45.6±2.1 g/individual cultured in a plastic box (40×30×30 cm3. The stocking densities was 10 crab/box. Crab was cultured within 42 days and were fed two times a day by restricted method (15% of the total biomass. The result showed that C treatment produced 5.51 mg/L dissolved oxygen and gave the best result of mangrove crabs production performance  with 60% survival, 0.83±0.03 g/day absolute growth rate and food conversion ratio 1.1. It also showed good response to the stress that indicated by the cortisol level (10.159 µg/dL. The best results of coefficient of diversity showed by D treatment that was 13.5%. The water quality during study period was fluctuative as affected by different dissolved oxygen value. Keyword: mangrove crabs, dissolved oxygen, production performance  ABSTRAK Penelitian ini bertujuan menentukan kadar oksigen terlarut (OT atau dissolved oxygen (DO yang optimum melalui penentuan titik aerasi serta mengevalusi peranan oksigen terlarut terhadap kinerja produksi dan respons stres kepiting bakau Scylla serrata. Rancangan penelitian yang digunakan adalah rancangan acak lengkap dengan empat pelakuan (penambahan titik aerasi dengan rincian A, tidak menggunakan titik aerasi; B, satu titik aerasi; C, dua titik aerasi dan D, tiga titik aerasi dan tiga ulangan. Kepiting bakau yang digunakan memiliki berat rata-rata 45,6±2,1 g/ekor dengan padat tebar 10 ekor/wadah. Wadah yang digunakan selama pemeliharaan adalah bak fiber plastik yang berukuran 40�

Designing high pressure containers for research- principles and applications

International Nuclear Information System (INIS)

Anandkumar, V.

1997-01-01

The high pressure scientist looks for a well engineered pressure apparatus for high pressure experiments for 1 kbar (0.1 GPa) and above. Often, a variety of difficulties including the choice of materials, design configuration, optimum utilisation of the strength of materials used in the design, are encountered. This article is intended to help the high pressure scientist to select the design approach for pressure retaining container. The limitations imposed by the strength of available materials and engineering standards in building high pressure containers are discussed. Engineering solutions to overcome these limitations with optimal utilisation of the strength of the materials are also discussed. Novel methods to boost up the pressure retaining capacity like multilayered design and autofrettaging are compared along with their relative advantages and disadvantages. Special methods by which it is possible to attain pressures which are several times the yield strength of the materials of construction are presented. In this aspects such as the basis of the codes and their relevance in the design of high pressure equipment will also be described. Discussions are centered around the methods to tackle situations where experimental constraints dictate requirements of pressures higher than those permitted by design codes. Safety features are also discussed. (author)

The Effect of Fasting on Anthropometric Parameters and Blood Pressure Levels: A Report from Southern Iran

Directory of Open Access Journals (Sweden)

Leila Malekmakan

2017-12-01

Full Text Available Background: Ramadan is the fasting month among Muslims and the change in eating and sleep pattern can cause changes in human health. Objectives: This study was carried out to determine the effect of fasting in Ramadan on the anthropometric parameters and blood pressure level. Patients and Methods: This is a semi-experimental study conducted as before and after design on 93 staff of Shiraz University of Medical Sciences in 2014. The participants were selected through convenience sampling method. All the subjects were assessed for anthropometry parameters and blood pressure levels in two sections, before and after Ramadan. Data were presented as mean (SD or number (% for continuous or discrete variables, respectively. The data were analyzed via paired and independent t-test or Chi-square test. All the analyses were performed using the statistical Package for Social Sciences, version 17.0 (SPSS Inc., Chicago, IL, USA. P value less than 5% was considered significant. Results: All the subjects completed the study. In this study, 93 subjects with an age range of 25 - 57 years and mean of age 37.2 ± 7.9 years participated. Among them, 49 cases (52.7% were men. All the anthropometric parameters and blood pressure showed a significant difference; BMI: (26.1 ± 3.3 vs. 25.7 ± 3.2, P < 0.001, waist circumference: (89.1 ± 11.1 vs. 87.5 ± 11.1, P < 0.001, hip circumference: (101.4 ± 8.6 vs. 100.1 ± 8.5, P < 0.001, systolic blood pressure (101.7 ± 12.9 vs. 99.4 ± 12.7, P = 0.041, and diastolic blood pressure (72.3 ± 4.9 vs. 70.9 ± 5.3, P = 0.041. In addition, decrease in body mass index (P = 0.042 and weight (P = 0.03 were significantly greater in men. Conclusions: The data revealed that Ramadan can reduce anthropometric parameters and blood pressure levels. It was found that reduction in BMI and HC in men was significantly greater than women

The impact of feedstock cost on technology selection and optimum size

International Nuclear Information System (INIS)

Cameron, Jay B.; Kumar, Amit; Flynn, Peter C.

2007-01-01

Development of biomass projects at optimum size and technology enhances the role that biomass can make in mitigating greenhouse gas. Optimum sized plants can be built when biomass resources are sufficient to meet feedstock demand; examples include wood and forest harvest residues from extensive forests, and grain straw and corn stover from large agricultural regions. The impact of feedstock cost on technology selection is evaluated by comparing the cost of power from the gasification and direct combustion of boreal forest wood chips. Optimum size is a function of plant cost and the distance variable cost (DVC, $ dry tonne -1 km -1 ) of the biomass fuel; distance fixed costs (DFC, $ dry tonne -1 ) such as acquisition, harvesting, loading and unloading do not impact optimum size. At low values of DVC and DFC, as occur with wood chips sourced from the boreal forest, direct combustion has a lower power cost than gasification. At higher values of DVC and DFC, gasification has a lower power cost than direct combustion. This crossover in most economic technology will always arise when a more efficient technology with a higher capital cost per unit of output is compared to a less efficient technology with a lower capital cost per unit of output. In such cases technology selection cannot be separated from an analysis of feedstock cost

Full length cluster level swell data at pressures from 2 to 40 bar

International Nuclear Information System (INIS)

Pearson, K.G.

1987-11-01

This paper gives results of level swell experiments at pressures up to 40 bar, performed at Winfrith in 1981 as described elsewhere. The results have been used by a number of workers to develop voidage correlations and to assess safety codes. The experiment and experimental rig used are described. The results are tabulated. (author)

Utility of formulas predicting the optimal nasal continuous positive airway pressure in a Greek population.

Science.gov (United States)

Schiza, Sophia E; Bouloukaki, Izolde; Mermigkis, Charalampos; Panagou, Panagiotis; Tzanakis, Nikolaos; Moniaki, Violeta; Tzortzaki, Eleni; Siafakas, Nikolaos M

2011-09-01

There have been reports that optimal CPAP pressure can be predicted from a previously derived formula, with the Hoffstein formula being the most accurate and accepted in the literature so far. However, the validation of this predictive model has not been applied in different clinical settings. Our aim was to compare both the Hoffstein prediction formula and a newly derived formula to the CPAP pressure setting assessed during a formal CPAP titration study. We prospectively studied 1,111 patients (871 males/240 females) with obstructive sleep apnea hypopnea syndrome (OSAHS) undergoing a CPAP titration procedure. In this large population sample, we tested the Hoffstein formula, utilizing body mass index (BMI), neck circumference and apnea/hypopnea index (AHI), and we compared it with our new formula that included not only AHI and BMI but also smoking history and gender adjustment. We found that using the Hoffstein prediction formula, successful prediction (predicted CPAP pressure within ±2 cm H(2)O compared to the finally assessed optimum CPAP pressure during titration) was accomplished in 873 patients (79%), with significant correlation between CPAP predicted pressure (CPAPpred(1)) and the optimum CPAP pressure (CPAPopt) [r = 0.364, p history and gender adjustment, successful prediction was accomplished in 1,057 patients (95%), with significant correlation between CPAP predicted pressure (CPAPpred(2)) and the CPAPopt (r = 0.392, p titration. It may also be possible to shorten CPAP titration and perhaps in selected cases to combine it with the initial diagnostic study.

Optimal level of continuous positive airway pressure: auto-adjusting titration versus titration with a predictive equation.

Science.gov (United States)

Choi, Ji Ho; Jun, Young Joon; Oh, Jeong In; Jung, Jong Yoon; Hwang, Gyu Ho; Kwon, Soon Young; Lee, Heung Man; Kim, Tae Hoon; Lee, Sang Hag; Lee, Seung Hoon

2013-05-01

The aims of the present study were twofold. We sought to compare two methods of titrating the level of continuous positive airway pressure (CPAP) - auto-adjusting titration and titration using a predictive equation - with full-night manual titration used as the benchmark. We also investigated the reliability of the two methods in patients with obstructive sleep apnea syndrome (OSAS). Twenty consecutive adult patients with OSAS who had successful, full-night manual and auto-adjusting CPAP titration participated in this study. The titration pressure level was calculated with a previously developed predictive equation based on body mass index and apnea-hypopnea index. The mean titration pressure levels obtained with the manual, auto-adjusting, and predictive equation methods were 9.0 +/- 3.6, 9.4 +/- 3.0, and 8.1 +/- 1.6 cm H2O,respectively. There was a significant difference in the concordance within the range of +/- 2 cm H2O (p = 0.019) between both the auto-adjusting titration and the titration using the predictive equation compared to the full-night manual titration. However, there was no significant difference in the concordance within the range of +/- 1 cm H2O (p > 0.999). When compared to full-night manual titration as the standard method, auto-adjusting titration appears to be more reliable than using a predictive equation for determining the optimal CPAP level in patients with OSAS.

Molecular pathways associated with blood pressure and hexadecanedioate levels.

Directory of Open Access Journals (Sweden)

Cristina Menni

Full Text Available The dicarboxylic acid hexadecanedioate is associated with increased blood pressure (BP and mortality in humans and feeding it to rats raises BP. Here we aim to characterise the molecular pathways that influence levels of hexadecanedioate linked to BP regulation, using genetic and transcriptomic studies. The top associations for hexadecanedioate in a genome-wide association scan (GWAS conducted on 6447 individuals from the TwinsUK and KORA cohorts were tested for association with BP and hypertension in the International Consortium for BP and in a GWAS of BP extremes. Transcriptomic analyses correlating hexadecanedioate with gene expression levels in adipose tissue in 740 TwinsUK participants were further performed. GWAS showed 242 SNPs mapping to two independent loci achieving genome-wide significance. In rs414056 in the SCLO1B1 gene (Beta(SE = -0.088(0.006P = 1.65 x 10-51, P < 1 x 10-51, the allele previously associated with increased risk of statin associated myopathy is associated with higher hexadecanedioate levels. However this SNP did not show association with BP or hypertension. The top SNP in the second locus rs6663731 mapped to the intronic region of CYP4Z2P on chromosome 1 (0.045(0.007, P = 5.49x10-11. Hexadecanedioate levels also correlate with adipose tissue gene-expression of the 3 out of 4 CYP4 probes (P<0.05 and of alcohol dehydrogenase probes (Beta(SE = 0.12(0.02; P = 6.04x10-11. High circulating levels of hexadecanedioate determine a significant effect of alcohol intake on BP (SBP: 1.12(0.34, P = 0.001; DBP: 0.70(0.22, P = 0.002, while no effect is seen in the lower hexadecanedioate level group. In conclusion, levels in fat of ADH1A, ADH1B and CYP4 encoding enzymes in the omega oxidation pathway, are correlated with hexadecanedioate levels. Hexadecanedioate appears to regulate the effect of alcohol on BP.

The optimum tension for bridging sutures in transosseous-equivalent rotator cuff repair: a cadaveric biomechanical study.

Science.gov (United States)

Park, Ji Soon; McGarry, Michelle H; Campbell, Sean T; Seo, Hyuk Jun; Lee, Yeon Soo; Kim, Sae Hoon; Lee, Thay Q; Oh, Joo Han

2015-09-01

Transosseous-equivalent (TOE) rotator cuff repair can increase contact area and contact pressure between the repaired cuff tendon and bony footprint and can show higher ultimate loads to failure and smaller gap formation compared with other repair techniques. However, it has been suggested that medial rotator cuff failure after TOE repair may result from increased bridging suture tension. To determine optimum bridging suture tension in TOE repair by evaluating footprint contact and construct failure characteristics at different tensions. Controlled laboratory study. A total of 18 fresh-frozen cadaveric shoulders, randomly divided into 3 groups, were constructed with a TOE configuration using the same medial suture anchor and placing a Tekscan sensing pad between the repaired rotator cuff tendon and footprint. Nine of the 18 shoulders were used to measure footprint contact characteristics. With use of the Tekscan measurement system, the contact pressure and area between the rotator cuff tendon and greater tuberosity were quantified for bridging suture tensions of 60, 90, and 120 N with glenohumeral abduction angles of 0° and 30° and humeral rotation angles of 30° (internal), 0°, and 30° (external). TOE constructs of all 18 shoulders then underwent construct failure testing (cyclic loading and load to failure) to determine the yield load, ultimate load, stiffness, hysteresis, strain, and failure mode at 60 and 120 N of tension. As bridging suture tension increased, contact force, contact pressure, and peak pressure increased significantly at all positions (P .05 for all). Increasing bridging suture tension to over 90 N did not improve contact area but did increase contact force and pressure. Bridging suture tension did not significantly affect ultimate failure loads. Considering the risks of overtensioning bridging sutures, it may be clinically more beneficial to keep bridging suture tension below 90 N. © 2015 The Author(s).

Applied orthogonal experiment design for the optimum microwave ...

African Journals Online (AJOL)

An experiment on polysaccharides from Rhodiolae Radix (PRR) extraction was carried out using microwave-assisted extraction (MAE) method with an objective to establishing the optimum MAE conditions of PRR. Single factor experiments were performed to determine the appropriate range of extraction conditions, and the ...

Analysis of an ultrasonic level device for in-core Pressurized Water Reactor coolant detection

International Nuclear Information System (INIS)

Johnson, K.R.

1981-01-01

A rigorous semi-empirical approach was undertaken to model the response of an ultrasonic level device (ULD) for application to in-core coolant detection in Pressurized Water Reactors (PWRs). An equation is derived for the torsional wave velocity v/sub t phi/ in the ULD. Existing data reduction techniques were analyzed and compared to results from use of the derived equation. Both methods yield liquid level measurements with errors of approx. 5%. A sensitivity study on probe performance at reactor conditions predicts reduced level responsivity from data at lower temperatures

Choosing the optimum burnup

International Nuclear Information System (INIS)

Geller, L.; Goldstein, L.; Franks, W.A.

1986-01-01

This paper reviews some of the considerations utilities must evaluate when going to higher discharge burnups. The advantages and disadvantages of higher discharge burnups are described, as well as a consistent approach for evaluating optimum discharge burnup and its comparison to current practice. When an analysis is performed over the life of the plant, the design of the terminal cycles has significant impact on the lifetime savings from higher burnups. Designs for high burnup cycles have a greater average inventory value in the core. As one goes to higher burnup, there is a greater likelihood of discarding a larger value in unused fuel unless the terminal cycles are designed carefully. This effect can be large enough in some cases to wipe out the lifetime cost savings relative to operating with a higher discharge burnup cycle

Association of blood pressure and metabolic syndrome components with magnesium levels in drinking water in some Serbian municipalities.

Science.gov (United States)

Rasic-Milutinovic, Zorica; Perunicic-Pekovic, Gordana; Jovanovic, Dragana; Gluvic, Zoran; Cankovic-Kadijevic, Milce

2012-03-01

Chronic exposure to insufficient levels of magnesium (Mg) in drinking water increases the risk of magnesium deficiency and its association with hypertension, dyslipidemia and type 2 diabetes mellitus. The aim of the study was to assess the potential association of mineral contents in drinking water with blood pressure and other components of metabolic syndrome (MetS) (BMI as measure of obesity, triglycerides, glucose, and insulin resistance, index-HOMA IR), in a healthy population. This study was conducted in three randomly selected municipalities (Pozarevac, Grocka and Banovci), and recruited 90 healthy blood donors, aged 20-50 years. The Pozarevac area had a four times higher mean Mg level in drinking water (42 mg L(-1)) than Grocka (11 mg L(-1)). Diastolic blood pressure was lowest in subjects from Pozarevac. Serum Mg (sMg) was highest, and serum Ca(2+)/Mg (sCa/Mg) lowest in subjects from Pozarevac, and after adjustment for confounders (age, gender, BMI), only total cholesterol and sMg levels were independent predictors of diastolic blood pressure, sMg levels were independent predictors of triglycerides, and sCa/Mg predicted glucose levels. These results suggest that Mg supplementation in areas of lower magnesium levels in drinking water may be an important measure in the prevention of hypertension and MetS in general.

Constraint-Based Local Search for Constrained Optimum Paths Problems

Science.gov (United States)

Pham, Quang Dung; Deville, Yves; van Hentenryck, Pascal

Constrained Optimum Path (COP) problems arise in many real-life applications and are ubiquitous in communication networks. They have been traditionally approached by dedicated algorithms, which are often hard to extend with side constraints and to apply widely. This paper proposes a constraint-based local search (CBLS) framework for COP applications, bringing the compositionality, reuse, and extensibility at the core of CBLS and CP systems. The modeling contribution is the ability to express compositional models for various COP applications at a high level of abstraction, while cleanly separating the model and the search procedure. The main technical contribution is a connected neighborhood based on rooted spanning trees to find high-quality solutions to COP problems. The framework, implemented in COMET, is applied to Resource Constrained Shortest Path (RCSP) problems (with and without side constraints) and to the edge-disjoint paths problem (EDP). Computational results show the potential significance of the approach.

An optimum analysis sequence for environmental gamma-ray spectrometry

International Nuclear Information System (INIS)

De la Torre, F.; Rios M, C.; Ruvalcaba A, M. G.; Mireles G, F.; Saucedo A, S.; Davila R, I.; Pinedo, J. L.

2010-10-01

This work aims to obtain an optimum analysis sequence for environmental gamma-ray spectroscopy by means of Genie 2000 (Canberra). Twenty different analysis sequences were customized using different peak area percentages and different algorithms for: 1) peak finding, and 2) peak area determination, and with or without the use of a library -based on evaluated nuclear data- of common gamma-ray emitters in environmental samples. The use of an optimum analysis sequence with certified nuclear information avoids the problems originated by the significant variations in out-of-date nuclear parameters of commercial software libraries. Interference-free gamma ray energies with absolute emission probabilities greater than 3.75% were included in the customized library. The gamma-ray spectroscopy system (based on a Ge Re-3522 Canberra detector) was calibrated both in energy and shape by means of the IAEA-2002 reference spectra for software intercomparison. To test the performance of the analysis sequences, the IAEA-2002 reference spectrum was used. The z-score and the reduced χ 2 criteria were used to determine the optimum analysis sequence. The results show an appreciable variation in the peak area determinations and their corresponding uncertainties. Particularly, the combination of second derivative peak locate with simple peak area integration algorithms provides the greater accuracy. Lower accuracy comes from the combination of library directed peak locate algorithm and Genie's Gamma-M peak area determination. (Author)

Optimum Tower Crane Selection and Supporting Design Management

Directory of Open Access Journals (Sweden)

Hyo Won Sohn

2014-08-01

Full Text Available To optimize tower crane selection and supporting design, lifting requirements (as well as stability should be examined, followed by a review of economic feasibility. However, construction engineers establish plans based on data provided by equipment suppliers since there are no tools with which to thoroughly examine a support design's suitability for various crane types, and such plans lack the necessary supporting data. In such cases it is impossible to optimize a tower crane selection to satisfy lifting requirements in terms of cost, and to perform lateral support and foundation design. Thus, this study is intended to develop an optimum tower crane selection and supporting design management method based on stability. All cases that are capable of generating an optimization of approximately 3,000 ˜ 15,000 times are calculated to identify the candidate cranes with minimized cost, which are examined. The optimization method developed in the study is expected to support engineers in determining the optimum lifting equipment management.

RECENT APPROACHES IN THE OPTIMUM CURRENCY AREAS THEORY

Directory of Open Access Journals (Sweden)

AURA SOCOL

2011-04-01

Full Text Available This study is dealing with the endogenous characteristic of the OCA criteria, starting from the idea that a higherconformity of the business cycles will result in a better timing of the economic cycles and, thus, in getting closerto the quality of an optimum currency area. Thus, if the classical theory is focused on a static approach of theproblem, the new theories assert that these conditions are dynamic, and they cannot be positively affected evenby the establishment of the Economic and Monetary Union. The consequences are overwhelming, as theendogenous approach shows that a monetary union can be achieved even if all the conditions mentioned inMundell’s optimum currency areas theory are not met, showing that some of them may also be met subsequentto the unification. Thus, a country joining a monetary union, althogh it does not meet the criteria for an optimumcurrency area, will ex post lead to the increase of the integration and business cycle correlation degree.

Developing an optimum protocol for thermoluminescence dosimetry with gr-200 chips using Taguchi method

International Nuclear Information System (INIS)

Sadeghi, Maryam; Faghihi, Reza; Sina, Sedigheh

2017-01-01

Thermoluminescence dosimetry (TLD) is a powerful technique with wide applications in personal, environmental and clinical dosimetry. The optimum annealing, storage and reading protocols are very effective in accuracy of TLD response. The purpose of this study is to obtain an optimum protocol for GR-200; LiF: Mg, Cu, P, by optimizing the effective parameters, to increase the reliability of the TLD response using Taguchi method. Taguchi method has been used in this study for optimization of annealing, storage and reading protocols of the TLDs. A number of 108 GR-200 chips were divided into 27 groups, each containing four chips. The TLDs were exposed to three different doses, and stored, annealed and read out by different procedures as suggested by Taguchi Method. By comparing the signal-to-noise ratios the optimum dosimetry procedure was obtained. According to the results, the optimum values for annealing temperature (de.C), Annealing Time (s), Annealing to Exposure time (d), Exposure to Readout time (d), Pre-heat Temperature (de.C), Pre-heat Time (s), Heating Rate (de.C/s), Maximum Temperature of Readout (de.C), readout time (s) and Storage Temperature (de.C) are 240, 90, 1, 2, 50, 0, 15, 240, 13 and -20, respectively. Using the optimum protocol, an efficient glow curve with low residual signals can be achieved. Using optimum protocol obtained by Taguchi method, the dosimetry can be effectively performed with great accuracy. (authors)

Asphaltene laboratory assessment of a heavy onshore reservoir during pressure, temperature and composition variations to predict asphaltene onset pressure

Energy Technology Data Exchange (ETDEWEB)

Bahrami, Peyman; Ahmadi, Yaser [Islamic Azad University, Tehran (Iran, Islamic Republic of); Kharrat, Riyaz [Petroleum University of Technology, Tehran (Iran, Islamic Republic of); Mahdavi, Sedigheh; James, Lesley [Memorial University of Newfoundland, Saint John' s (Canada)

2015-02-15

An Iranian heavy oil reservoir recently encountered challenges in oil production rate, and further investigation has proven that asphaltene precipitation was the root cause of this problem. In addition, CO{sub 2} gas injection could be an appropriate remedy to enhance the production of heavy crudes. In this study, high pressure-high temperature asphaltene precipitation experiments were performed at different temperatures and pressures to investigate the asphaltene phase behavior during the natural depletion process and CO{sub 2} gas injection. Compositional modeling of experimental data predicted onset points at different temperatures which determine the zone of maximum probability of asphaltene precipitation for the studied heavy oil reservoir. Also, the effect of CO{sub 2} gas injection was investigated as a function of CO{sub 2} concentration and pressure. It was found that a CO{sub 2}-oil ratio of 40% is the optimum for limiting precipitation to have the least formation damage and surface instrument contamination.

Optimum energies for dual-energy computed tomography

International Nuclear Information System (INIS)

Talbert, A.J.; Brooks, R.A.; Morgenthaler, D.G.

1980-01-01

By performing a dual-energy scan, separate information can be obtained on the Compton and photoelectric components of attenuation for an unknown material. This procedure has been analysed for the optimum energies, and for the optimum dose distribution between the two scans. It was found that an equal dose at both energies was a good compromise, compared with optimising the dose distributing for either the Compton or photoelectric components individually. For monoenergetic beams, it was found that low energy of 40 keV produced minimum noise when using high-energy beams of 80 to 100 keV. This was true whether one maintained constant integral dose or constant surface dose. A low energy of 50 keV which is more nearly attainable in practice, produced almost as good a degree of accuracy. The analysis can be extended to polyenergetic beams by the inclusion of a noise factor. The above results were qualitatively unchanged, although the noise was increased by about 20% with integral dose equivalence and 50% with surface dose equivalence. It is very important to make the spectra as narrow as possible, especially at the low energy, in order to minimise the noise. (author)

Development of a technique for level measurement in pressure vessels using thermal probes and artificial neural networks

International Nuclear Information System (INIS)

Torres, Walmir Maximo

2008-01-01

A technique for level measurement in pressure vessels was developed using thermal probes with internal cooling and artificial neural networks (ANN's). This new concept of thermal probes was experimentally tested in an experimental facility (BETSNI) with two test sections, ST1 and ST2. Two different thermal probes were designed and constructed: concentric tubes probe and U tube probe. A data acquisition system (DAS) was assembled to record the experimental data during the tests. Steady state and transient level tests were carried out and the experimental data obtained were used as learning and recall data sets in the ANN's program RETRO-05 that simulate a multilayer perceptron with backpropagation. The results of the analysis show that the technique can be applied for level measurements in pressure vessel. The technique is applied for a less input temperature data than the initially designed to the probes. The technique is robust and can be used in case of lack of some temperature data. Experimental data available in literature from electrically heated thermal probe were also used in the ANN's analysis producing good results. The results of the ANN's analysis show that the technique can be improved and applied to level measurements in pressure vessels. (author)

Optimum development temperature and duration for nuclear plate

International Nuclear Information System (INIS)

Nagoshi, Chieko.

1975-01-01

Sakura 100 μm thick nuclear plates have been employed to determine optimum temperature and duration of the Amidol developer for low energy protons (Ep 0 C were tried for periods of 15--35 min. For Ep 0 C and for development time less than 30 min. (auth.)

Optimum workforce-size model using dynamic programming approach

African Journals Online (AJOL)

This paper presents an optimum workforce-size model which determines the minimum number of excess workers (overstaffing) as well as the minimum total recruitment cost during a specified planning horizon. The model is an extension of other existing dynamic programming models for manpower planning in the sense ...

DETERMINATION OF OPTIMUM THREONINE REQUIREMENTS OF JAPANESE QUAIL (Coturnix coturnix japonica CHICKS REARED UNDER TROPICAL ENVIRONMENT

Directory of Open Access Journals (Sweden)

Isaac Samuel

2017-12-01

Full Text Available Threonine, like most amino acids, is traditionally noted for its role in protein synthesis. However, dietary threonine concentration required for the maximum performance of Japanese quails is yet to be determined, therefore, a study was conducted to determine the optimum threonine requirement of Japanese quail chicks in the tropical environment. A total of four hundred and fifty, two weeks old quail chicks (mixed sexes were randomly allocated to five dietary treatments (0.67, 0.81, 0.95, 1.08 and 1.22 % total threonine and replicated thrice in a completely randomized design (CRD. There were no significant differences (P>0.05 in average weight gain, average feed intake, feed conversion ratio and age at first lay of quails fed the dietary treatments. Weight of first egg laid was significantly (P0.05 similar for all treatments. There were significant differences (P0.05. It was concluded that the performance of birds were not influenced by the dietary treatments up to the highest dietary level of threonine studied (1.22%. Therefore, it is possible that the optimum dietary level of threonine may be above 1.22 %. Further studies will be necessary to establish higher doses of dietary threonine requirement of Japanese quails reared under tropical climatic environment.

Optimum modellings of atmospheric diffusion of radioactive effluents and exposure doses in the accident consequence assessment (Level 3 PSA)

International Nuclear Information System (INIS)

Kim, Byung Woo; Lee, Young Bok; Han, Moon Hee; Kim, Eun Han; Suh, Kyung Suk; Hwang, Won Tae

1992-12-01

Atmospheric diffusion and exposure strongly dependent on the environment were firstly considered in the full spectrum of accident consequence assessment to establish based on Korean conditions. An optimum weather category based on Korean climate and site-specific meteorology of Kori region was established by statistical analysis of measured data for 10 years. And a trajectory model was selected as the optimal one in the ACA by reviewing several existing diffusion models. Following aspects were considered in this selection as availability of meteorological data, ability to treat the change to wind direction, easy applicability of the model, and restriction of CPU time and core memory in current computers. Numerical integration method of our own was selected as the optimal dose assessment tool of external exposure. Unit dose rate was firstly computed with this method as the function of energy level of radionuclide, size of lattice, and distance between source and receptor, and then the results were rearranged as the data library for the rapid access to the ACA run. Dynamic ecosystem modelling has been done in order to estimate the seasonal variation of radioactivity for the assessment of ingestion exposure, considering Korean ingestion behavior, agricultural practice and the transportation. There is a lot of uncertainty in a countermeasure model due to the assumed values of parameters such as fraction of population with different shielding factor and driving speed. A new countermeasure model was developed using the concept of fuzzy set theory, since it provided the mathematical tools which could characterize the uncertainty involved in countermeasure modelling. (Author)

Estimation of sound pressure levels of voiced speech from skin vibration of the neck

NARCIS (Netherlands)

Svec, JG; Titze, IR; Popolo, PS

How accurately can sound pressure levels (SPLs) of speech be estimated from skin vibration of the neck? Measurements using a small accelerometer were carried out in 27 subjects (10 males and 17 females) who read Rainbow and Marvin Williams passages in soft, comfortable, and loud voice, while skin

Defining an optimum pumping-time requirement for sampling ground-water wells on the Hanford site

International Nuclear Information System (INIS)

Scharnhorst, N.L.

1982-04-01

The objective was to determine the optimum time period necessary to pump water from a well before a representative sample of the ground water can be obtained. It was assumed that a representative sample has been collected if the concentration of chemical parameters is the same in a number of samples taken consecutively, so that the concentration of parameters does not vary with time of collection. Ground-water samples used in this project were obtained by pumping selected wells on the Hanford Site. At each well, samples were taken at two minute intervals, and on each sample various chemical analyses were performed. Samples were checked for pH, sulfate, iron, specific conductivity, chloride, nitrate and alkalinity. The data showed that pH, alkalinity, sulfate and specific conductivity levels stabilized almost immediately after pumping of the well began. In many wells, the chloride and nitrate levels were unstable throughout the 38-minute sampling period. Iron levels, however, did not behave in either fashion. The concentration of iron in the samples was high when pumping began but dropped rapidly as pumping continued. The best explanation for this is that iron is flushed from the sides of the casing into the well when pumping begins. After several minutes of pumping, most of the dissolved iron is washed from the well casing and the iron concentration reaches a stable plateau representative of the iron concentration in the ground water.Since iron concentration takes longest to stabilize, the optimum pumping time for a well is based on the iron stabilization time for that well

Pressurized oxy-coal combustion: Ideally flexible to uncertainties

International Nuclear Information System (INIS)

Zebian, Hussam; Mitsos, Alexander

2013-01-01

Simultaneous multi-variable gradient-based optimization with multi-start is performed on a 300 MWe wet-recycling pressurized oxy-coal combustion process with carbon capture and sequestration, subject to uncertainty in fuel, ambient conditions, and other input specifications. Two forms of flue gas thermal recovery are studied, a surface heat exchanger and a direct contact separation column. Optimization enables ideal flexibility in the processes: when changing the coal utilized, the performance is not compromised compared to the optimum performance of a process specifically designed for that coal. Similarly, the processes are immune to other uncertainties like ambient conditions, air flow, slurry water flow, atomizer stream flow and the oxidizer stream oxygen purity. Consequently, stochastic programming is shown to be unnecessary. Close to optimum design, the processes are also shown to be insensitive towards design variables such as the areas of the feedwater heaters. Recently proposed thermodynamic criteria are used as embedded design specifications in the optimization process, rendering it faster and more robust. - Highlights: • Proposed formulation to assess the flexibility of power generation processes facing uncertainties. • Obtained ideal flexibility of pressurized oxy-coal combustion with respect to coal type. • Performance of processes under uncertainty match performance of optimal processes for specific set of inputs. • Stochastic programming is not required and instead hierarchic optimization is utilized

Utility Function and Optimum Consumption in the models with Habit Formation and Catching up with the Joneses

OpenAIRE

Naryshkin, Roman; Davison, Matt

2009-01-01

This paper analyzes popular time-nonseparable utility functions that describe "habit formation" consumer preferences comparing current consumption with the time averaged past consumption of the same individual and "catching up with the Joneses" (CuJ) models comparing individual consumption with a cross-sectional average consumption level. Few of these models give reasonable optimum consumption time series. We introduce theoretically justified utility specifications leading to a plausible cons...

Developing an Optimum Protocol for Thermoluminescence Dosimetry with GR-200 Chips using Taguchi Method.

Science.gov (United States)

Sadeghi, Maryam; Faghihi, Reza; Sina, Sedigheh

2017-06-15

Thermoluminescence dosimetry (TLD) is a powerful technique with wide applications in personal, environmental and clinical dosimetry. The optimum annealing, storage and reading protocols are very effective in accuracy of TLD response. The purpose of this study is to obtain an optimum protocol for GR-200; LiF: Mg, Cu, P, by optimizing the effective parameters, to increase the reliability of the TLD response using Taguchi method. Taguchi method has been used in this study for optimization of annealing, storage and reading protocols of the TLDs. A number of 108 GR-200 chips were divided into 27 groups, each containing four chips. The TLDs were exposed to three different doses, and stored, annealed and read out by different procedures as suggested by Taguchi Method. By comparing the signal-to-noise ratios the optimum dosimetry procedure was obtained. According to the results, the optimum values for annealing temperature (°C), Annealing Time (s), Annealing to Exposure time (d), Exposure to Readout time (d), Pre-heat Temperature (°C), Pre-heat Time (s), Heating Rate (°C/s), Maximum Temperature of Readout (°C), readout time (s) and Storage Temperature (°C) are 240, 90, 1, 2, 50, 0, 15, 240, 13 and -20, respectively. Using the optimum protocol, an efficient glow curve with low residual signals can be achieved. Using optimum protocol obtained by Taguchi method, the dosimetry can be effectively performed with great accuracy. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Generating AN Optimum Treatment Plan for External Beam Radiation Therapy.

Science.gov (United States)

Kabus, Irwin

1990-01-01

The application of linear programming to the generation of an optimum external beam radiation treatment plan is investigated. MPSX, an IBM linear programming software package was used. All data originated from the CAT scan of an actual patient who was treated for a pancreatic malignant tumor before this study began. An examination of several alternatives for representing the cross section of the patient showed that it was sufficient to use a set of strategically placed points in the vital organs and tumor and a grid of points spaced about one half inch apart for the healthy tissue. Optimum treatment plans were generated from objective functions representing various treatment philosophies. The optimum plans were based on allowing for 216 external radiation beams which accounted for wedges of any size. A beam reduction scheme then reduced the number of beams in the optimum plan to a number of beams small enough for implementation. Regardless of the objective function, the linear programming treatment plan preserved about 95% of the patient's right kidney vs. 59% for the plan the hospital actually administered to the patient. The clinician, on the case, found most of the linear programming treatment plans to be superior to the hospital plan. An investigation was made, using parametric linear programming, concerning any possible benefits derived from generating treatment plans based on objective functions made up of convex combinations of two objective functions, however, this proved to have only limited value. This study also found, through dual variable analysis, that there was no benefit gained from relaxing some of the constraints on the healthy regions of the anatomy. This conclusion was supported by the clinician. Finally several schemes were found that, under certain conditions, can further reduce the number of beams in the final linear programming treatment plan.

An optimum analysis sequence for environmental gamma-ray spectrometry

Energy Technology Data Exchange (ETDEWEB)

De la Torre, F.; Rios M, C.; Ruvalcaba A, M. G.; Mireles G, F.; Saucedo A, S.; Davila R, I.; Pinedo, J. L., E-mail: fta777@hotmail.co [Universidad Autonoma de Zacatecas, Centro Regional de Estudis Nucleares, Calle Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas (Mexico)

2010-10-15

This work aims to obtain an optimum analysis sequence for environmental gamma-ray spectroscopy by means of Genie 2000 (Canberra). Twenty different analysis sequences were customized using different peak area percentages and different algorithms for: 1) peak finding, and 2) peak area determination, and with or without the use of a library -based on evaluated nuclear data- of common gamma-ray emitters in environmental samples. The use of an optimum analysis sequence with certified nuclear information avoids the problems originated by the significant variations in out-of-date nuclear parameters of commercial software libraries. Interference-free gamma ray energies with absolute emission probabilities greater than 3.75% were included in the customized library. The gamma-ray spectroscopy system (based on a Ge Re-3522 Canberra detector) was calibrated both in energy and shape by means of the IAEA-2002 reference spectra for software intercomparison. To test the performance of the analysis sequences, the IAEA-2002 reference spectrum was used. The z-score and the reduced {chi}{sup 2} criteria were used to determine the optimum analysis sequence. The results show an appreciable variation in the peak area determinations and their corresponding uncertainties. Particularly, the combination of second derivative peak locate with simple peak area integration algorithms provides the greater accuracy. Lower accuracy comes from the combination of library directed peak locate algorithm and Genie's Gamma-M peak area determination. (Author)

Optimum design for 12 MeV linear induction accelerator diode

International Nuclear Information System (INIS)

Yu Haijun; Shi Jinshui; Li Qin; He Guorong; Ma Bing; Wang Jingsheng; Wang Liping

2001-01-01

A series of optimization designs of electron diode in 12 Mev linear induction accelerator are studied by using numerical simulation code MAGIC and experiment method in order to improve the electron beam quality. MAGIC code solves the Maxwell equations in the presence of charged particle, electron field distribution on cathode surface which influences electron emission is given, the optimum diode is obtained by comparing the results of experiment in 12 MeV linear induction accelerator. The author also gives SEM analysis and experiment comparison of velvet emission. Finally, emitted current I e = 8.52 kA, beam current I 8 ≥ 3.0 kA, targeted current I 0 ≥ 2.30 kA with optimum diode are obtained

Optimum design of exploding pusher target to produce maximum neutrons

International Nuclear Information System (INIS)

Kitagawa, Y.; Miyanaga, N.; Kato, Y.; Nakatsuka, M.; Nishiguchi, A.; Yabe, T.; Yamanaka, C.

1985-03-01

Exploding pusher target experiments have been conducted with the 1.052-μm GEKKO MII two-beam glass laser system to design an optimum target, which couples to the incident laser light most effectively to produce the maximum neutrons. Since hot electrons preheat the shell entirely in spite of strongly nonuniform irradiation, a simple model can design the optimum target, of which the shell/fuel interface is accelerated to 0.5 to 0.7 times the initial radius within a laser pulse. A 2-dimensional computer simulation supports this target design. The scaling of the neutron yield N with the laser power P is N ∝ P 2.4±0.4 . (author)

OPTIMUM PROGRAMMABLE CONTROL OF UNMANNED FLYING VEHICLE

Directory of Open Access Journals (Sweden)

A. А. Lobaty

2012-01-01

Full Text Available The paper considers an analytical synthesis problem pertaining to programmable control of an unmanned flying vehicle while steering it to the fixed space point. The problem has been solved while applying a maximum principle which takes into account a final control purpose and its integral expenses. The paper presents an optimum law of controlling overload variation of a flying vehicle that has been obtained analytically

Techniques for evaluating optimum data center operation

Science.gov (United States)

Hamann, Hendrik F.; Rodriguez, Sergio Adolfo Bermudez; Wehle, Hans-Dieter

2017-06-14

Techniques for modeling a data center are provided. In one aspect, a method for determining data center efficiency is provided. The method includes the following steps. Target parameters for the data center are obtained. Technology pre-requisite parameters for the data center are obtained. An optimum data center efficiency is determined given the target parameters for the data center and the technology pre-requisite parameters for the data center.

Adaptive pressure-controlled cellular structures for shape morphing I: design and analysis

International Nuclear Information System (INIS)

Luo, Quantian; Tong, Liyong

2013-01-01

This work investigates adaptive bio-inspired pressure cellular structures for shape morphing. Optimum designs for cellular structures with void and pressure cells are proposed and then structural analyses are conducted. In the present design, a unit cell is comprised of straight and curved walls. When compressed air is pumped into a pressure cell, the curved walls deform in bending due to the pressure difference in two adjacent cells that leads to overall structural deformation in extension. One-dimensional actuation strain up to 35% can be theoretically achieved. In part I, we present basic design concepts and cellular mechanics. Unlike conventional structural analysis for cellular structures, a statically indeterminate unit cell is considered and novel analytical formulations are derived for the present pressurized cellular structures in linear and nonlinear analyses. In part II, we will present experimental testing and finite element analysis to demonstrate the feasibility of the present pressurized cellular actuators for morphing wings and to validate the present cellular mechanics formulations. (paper)

Optimum performance analysis of an irreversible Diesel heat engine affected by variable heat capacities of working fluid

International Nuclear Information System (INIS)

Zhao, Yingru; Chen, Jincan

2007-01-01

An irreversible cycle model of the Diesel heat engine is established in which the temperature dependent heat capacities of the working fluid, the irreversibilities resulting from non-isentropic compression and expansion processes and heat leak losses through the cylinder wall are taken into account. The adiabatic equation of ideal gases with temperature dependent heat capacity is strictly deduced without using the additional approximation condition in the relevant literature and is used to analyze the performance of the Diesel heat engine. Expressions for the work output and efficiency of the cycle are derived by introducing the pressure ratio and the compression and expansion efficiencies. The performance characteristic curves of the Diesel heat engine are presented for a set of given parameters. The optimum criteria of some important parameters such as the work output, efficiency, pressure ratio and temperatures of the working fluid are obtained. Moreover, the influence of the compression and expansion efficiencies, variable heat capacities, heat leak and other parameters on the performance of the cycle is discussed in detail. The results obtained may provide a theoretical basis for both optimal design and operation of real Diesel heat engines

Evaluation of mathematical methods for predicting optimum dose of gamma radiation in sugarcane (Saccharum sp.)

International Nuclear Information System (INIS)

Wu, K.K.; Siddiqui, S.H.; Heinz, D.J.; Ladd, S.L.

1978-01-01

Two mathematical methods - the reversed logarithmic method and the regression method - were used to compare the predicted and the observed optimum gamma radiation dose (OD 50 ) in vegetative propagules of sugarcane. The reversed logarithmic method, usually used in sexually propagated crops, showed the largest difference between the predicted and observed optimum dose. The regression method resulted in a better prediction of the observed values and is suggested as a better method for the prediction of optimum dose for vegetatively propagated crops. (author)

Effect of optimum stratification on sampling with varying probabilities under proportional allocation

OpenAIRE

Syed Ejaz Husain Rizvi; Jaj P. Gupta; Manoj Bhargava

2007-01-01

The problem of optimum stratification on an auxiliary variable when the units from different strata are selected with probability proportional to the value of auxiliary variable (PPSWR) was considered by Singh (1975) for univariate case. In this paper we have extended the same problem, for proportional allocation, when two variates are under study. A cum. 3 R3(x) rule for obtaining approximately optimum strata boundaries has been provided. It has been shown theoretically as well as empiricall...

DETERMINATION of OPTIMUM CONDITION of PAPAIN ENZYME FROM PAPAYA VAR JAVA (Carica papaya

Directory of Open Access Journals (Sweden)

Aline Puspita Kusumadjaja

2010-06-01

Full Text Available A study to investigate the optimum condition of papain enzyme has been carried out. The condition that are investigated are pH and temperature, based on measurement of enzyme activity which is defined as mmole tyrosin that are released in reaction between papain enzyme and casein as substrat per minute. In this research, the papain enzyme was isolated from pepaya burung varietas Java. The enzyme was partially purified by precipitation method using 30% - 50% saturated acetone. The result showed that the optimum conditions of papain enzyme are in pH 6 with activity 2,606 U/mL, and temperature at 50 oC with activity 2,469 U/mL. Keywords : Papaya var Java, papain, optimum condition, enzymatic activity

Effects of hydrostatic pressure and temperature on the uptake and respiration of amino acids by a facultatively psychrophilic marine bacterium.

Science.gov (United States)

Paul, K. L.; Morita, R. Y.

1971-01-01

Studies of pressure and temperature effects on glutamic acid transport and utilization indicated that hydrostatic pressure and low temperature inhibit glutamate transport more than glutamate respiration. The effects of pressure on transport were reduced at temperatures near the optimum. Similar results were obtained for glycine, phenylalanine, and proline. Pressure effects on the transport systems of all four amino acids were reversible to some degree. Both proline and glutamic acid were able to protect their transport proteins against pressure damage. The data presented indicate that the uptake of amino acids by cells under pressure is inhibited, which is the cause of their inability to grow under pressure.

Optimum condition determination of Rirang uranium ores grinding using ball mill

International Nuclear Information System (INIS)

Affandi, Kosim; Waluyo, Sugeng; Sarono, Budi; Sujono; Muhammad

2002-01-01

The grinding experiment on Rirang Uranium ore has been carried out with the aim is to find out the optimum condition of wet grinding using ball mill to produce particle size -325, -200 and -100 mesh. This will be used for decomposition feed the test was done by examine the parameters comparison of ore's weight against ball's weight and time of grinding. The test shown that the product of particle size -325 meshes was achieved optimum condition at the comparison ore's weight: ball = 1:3, grinding time 150 minutes, % solid 60, speed rotation of ball mill 60 rpm and recovery of grinding was 93.51 % of -325 mesh. The product of particle size -200 mesh was achieved optimum condition at comparison ore's weight: ball = 1:2, time of grinding 60 minutes, the fraction of + 200 mesh was regrind, the recovery of grinding 6.82% at particle size of (-200 + 250) mesh, 5.75 % at (-250 + 325)m mesh and, 47.93 % -325 mesh. The product of particle size -100 mesh was achieved the optimum condition at comparison ore's weight: ball = 1:2, time of grinding at 30 minutes particle size +100 mesh regrinding using mortar grinder, recovery of grinding 30.10% at particle size (-100 + 150) m, 12.28 % at (-150 + 200) mesh, 15.92 % at (-200 + 250) mesh, 12.44 % at (-250 + 325) mesh and 29.26 % -325 mesh. The determination of specific gravity of Rirang uranium ore was between 4.15 - 4.55 g/cm 3

REGARDING "TRAGIC ECONOMIC OPTIMUM" FROM HOLISTIC+ PERSPECTIVE

Directory of Open Access Journals (Sweden)

Constantin Popescu

2010-12-01

Full Text Available Communication aims to discuss the new scientific vision of "the entire integrated" as it follows the recent achievements of quantum physics, psychology and biology. From this perspective, economy is seen as a living organism, part of the social organism and together with de bright ecology. The optimum of the economy as a living organism is based on dynamic compatibilities with all common living requirements. The evolution of economic life is organically linked to the unavoidable circumstances contained in the form of V. Frankl ‘s tragic triad consisting of: pain, guilt and death. In interaction with the holistic triad circumscribed by limitations, uncertainties and open interdependencies, the tragic economic optimum (TEO is formed. It can be understood as that state of economic life in which freedom of choice of scarce resources under uncertainty has in the compatibility of rationality and hope the development criteria of MEANING. TEO means to say YES to economic life even in conditions of resource limitations, bankruptcies and unemployment, negative externalities, stress, etc. By respiritualization of responsibility using scientific knowledge. TEO - involves multicriteria modeling of economic life by integrating human demands, community, environmental, spiritual and business development in the assessment predicting human GDP as a variable wave aggregate.

Impacts of optimum cost effective energy efficiency standards

International Nuclear Information System (INIS)

Brancic, A.B.; Peters, J.S.; Arch, M.

1991-01-01

Building Codes are increasingly required to be responsive to social and economic policy concerns. In 1990 the State of Connecticut passes An Act Concerning Global Warming, Public Act 90-219, which mandates the revision of the state building code to require that buildings and building elements be designed to provide optimum cost-effective energy efficiency over the useful life of the building. Further, such revision must meet the American Society of Heating, Refrigerating and Air Conditioning Engineers (ASHRAE) Standard 90.1 - 1989. As the largest electric energy supplier in Connecticut, Northeast Utilities (NU) sponsored a pilot study of the cost effectiveness of alternative building code standards for commercial construction. This paper reports on this study which analyzed design and construction means, building elements, incremental construction costs, and energy savings to determine the optimum cost-effective building code standard. Findings are that ASHRAE 90.1 results in 21% energy savings and alternative standards above it result in significant additional savings. Benefit/cost analysis showed that both are cost effective

Trends in Intense Typhoon Minimum Sea Level Pressure

Directory of Open Access Journals (Sweden)

Stephen L. Durden

2012-01-01

Full Text Available A number of recent publications have examined trends in the maximum wind speed of tropical cyclones in various basins. In this communication, the author focuses on typhoons in the western North Pacific. Rather than maximum wind speed, the intensity of the storms is measured by their lifetime minimum sea level pressure (MSLP. Quantile regression is used to test for trends in storms of extreme intensity. The results indicate that there is a trend of decreasing intensity in the most intense storms as measured by MSLP over the period 1951–2010. However, when the data are broken into intervals 1951–1987 and 1987–2010, neither interval has a significant trend, but the intensity quantiles for the two periods differ. Reasons for this are discussed, including the cessation of aircraft reconnaissance in 1987. The author also finds that the average typhoon intensity is greater in El Nino years, while the intensity of the strongest typhoons shows no significant relation to El Nino Southern Oscillation.

Effect of advance meditation program on electrocardiogram, blood pressure, and stress level in young healthy adults

Directory of Open Access Journals (Sweden)

M Sharma

2017-01-01

Conclusion: AMP has its positive effects on ECG, blood pressure, and stress level. Thus, it can be considered as one of the important nonpharmacological methods for prevention of stress, anxiety, and cardiovascular diseases.

Transcritical CO2 power cycle – Effects of regenerative heating using turbine bleed gas at intermediate pressure

International Nuclear Information System (INIS)

Mondal, Subha; De, Sudipta

2015-01-01

For energy utilization from low temperature waste heat, CO 2 is a potential working fluid due to its lower critical temperature. In this work, assuming finite quantity of flue gas available at low temperature (200 °C), a thermodynamic model is developed for a transcritical CO 2 power cycle utilizing turbine bleed gas for regenerative heating. Analysis show that the cycle performance improves with higher value of bleed ratio. However, for a specified bleed pressure and bleed gas temperature at the regenerator exit, maximum practical value of bleed ratio may be fixed by considering the exponential growth of the regenerator size (specified by NTU (number of transfer unit)). Most significant observation is the existence of optimum bleed pressures corresponding to maximum 1st law efficiency or minimum cycle irreversibility for specified values of remaining cycle parameters. - Highlights: • Thermodynamic model for Transcritical CO 2 cycle with bleed gas are developed. • Effects of bleed ratio, pressure, and regenerator exit gas temperature are studied. • 1st and 2nd law efficiencies are estimated. • An optimum bleed pressure for maximum 1st and 2nd efficiencies is obtained. • Maximum value of 1st law efficiency is limited by regenerator size

Structural integrity investigation for RPV with various cooling water levels under pressurized melting pool

Directory of Open Access Journals (Sweden)

J. Mao

2018-03-01

Full Text Available The strategy denoted as in-vessel retention (IVR is widely used in severe accident (SA management by most advanced nuclear power plants. The essence of IVR mitigation is to provide long-term external water cooling in maintaining the reactor pressure vessel (RPV integrity. Actually, the traditional IVR concept assumed that RPV was fully submerged into the water flooding, and the melting pool was depressurized during the SA. The above assumptions weren't seriously challenged until the occurrence of Fukushima accident on 2011, suggesting the structural behavior had not been appropriately assessed. Therefore, the paper tries to address the structure-related issue on determining whether RPV safety can be maintained or not with the effect of various water levels and internal pressures created from core meltdown accident. In achieving it, the RPV structural behaviors are numerically investigated in terms of several field parameters, such as temperature, deformation, stress, plastic strain, creep strain, and total damage. Due to the presence of high temperature melt on the inside and water cooling on the outside, the RPV failure is governed by the failure mechanisms of creep, thermal-plasticity and plasticity. The creep and plastic damages are interacted with each other, which further accelerate the failure process. Through detailed investigation, it is found that the internal pressure as well as water levels plays an important role in determining the RPV failure time, mode and site.

Preparation and Optimization of 10-Hydroxycamptothecin Nanocolloidal Particles Using Antisolvent Method Combined with High Pressure Homogenization

Directory of Open Access Journals (Sweden)

Bolin Lian

2017-01-01

Full Text Available The aim of this study was to prepare 10-hydroxycamptothecin nanocolloidal particles (HCPTNPs to increase the solubility of drugs, reduce the toxicity, improve the stability of the drug, and so forth. HCPTNPs was prepared by antisolvent precipitation (AP method combined with high pressure homogenization (HPH, followed by lyophilization. The main parameters during antisolvent process including volume ratio of dimethyl sulfoxide (DMSO and H2O and dripping speed were optimized and their effects on mean particle size (MPS and yield of HCPT primary particles were investigated. In the high pressure homogeneous procedure, types of surfactants, amount of surfactants, and homogenization pressure (HP were optimized and their influences on MPS, zeta potential (ZP, and morphology were analyzed. The optimum conditions of HCPTNPs were as follows: 0.2 mg/mL HCPT aqueous suspension, 1% of ASS, 1000 bar of HP, and 20 passes. Finally, the HCPTNPs via lyophilization using glucose as lyoprotectant under optimum conditions had an MPS of 179.6 nm and a ZP of 28.79 ± 1.97 mV. The short-term stability of HCPTNPs indicated that the MPS changed in a small range.

Dependence of optimum baseline setting on scatter fraction and detector response function

International Nuclear Information System (INIS)

Atkins, F.B.; Beck, R.N.; Hoffer, P.B.; Palmer, D.

1977-01-01

A theoretical and experimental investigation has been undertaken to determine the dependence of an optimum baseline setting on the amount of scattered radiation recorded in a spectrum, and on the energy resolution of the detector. In particular, baseline settings were established for clinical examinations which differed greatly in the amount of scattered radiation, namely, liver and brain scans, for which individual variations were found to produce only minimal fluctuations in the optimum baseline settings. This analysis resulted in an optimum baseline setting of 125.0 keV for brain scans and 127.2 keV for liver scans for the scintillation camera used in these studies. The criterion that was used is based on statistical considerations of the measurement of an unscattered component in the presence of a background due to scattered photons. The limitations of such a criterion are discussed, and phantom images are presented to illustrate these effects at various baseline settings. (author)

Comparison between coasting and bunched beams on optimum stochastic cooling and signal suppression

International Nuclear Information System (INIS)

Wei, J.

1991-01-01

A comparison has been performed between coasting and bunched particle beams pertaining to the mechanism of stochastic cooling. In the case that particles occupy the entire sinusoidal rf bucket, the optimum cooling rate for the bunched beam is shown to be the same as that predicted from the coasting-beam theory using local particle density. However, in the case that particles occupy only the center of the bucket, the optimum rate decreases in proportion to the ratio of the bunch area to the bucket area. Furthermore, it has been shown for both coasting and bunched beams that particle motion is stable upon signal suppression if the amplitude of the gain is less than twice the optimum value over the entire frequency bandwidth of the cooling system. 7 refs., 1 fig

Comparative analysis of diffused solar radiation models for optimum tilt angle determination for Indian locations

International Nuclear Information System (INIS)

Yadav, P.; Chandel, S.S.

2014-01-01

Tilt angle and orientation greatly are influenced on the performance of the solar photo voltaic panels. The tilt angle of solar photovoltaic panels is one of the important parameters for the optimum sizing of solar photovoltaic systems. This paper analyses six different isotropic and anisotropic diffused solar radiation models for optimum tilt angle determination. The predicted optimum tilt angles are compared with the experimentally measured values for summer season under outdoor conditions. The Liu and Jordan model is found to exhibit t lowest error as compared to other models for the location. (author)

Mediterranean diet and insulin sensitivity, lipid profile and blood pressure levels, in overweight and obese people; The Attica study

Directory of Open Access Journals (Sweden)

Zampelas Antonis

2007-09-01

Full Text Available Abstract Background We aimed to investigate if overweight and obese adults "close" to Mediterranean diet present better insulin, lipids profile and better pressure levels, compared to individuals close to a more Westernized diet. Methods The ATTICA study is a population-based cohort that has randomly enrolled 3042 adult men and women, stratified by age – gender, from the greater area of Athens, during 2001–2002. Of them, in this work were have studied 1762 participants with excess body weight, meaning overweight (BMI: 25–29.9 kg/m2 and obese (BMI>30 kg/m2. 1064 were men and 698 women (20–89 years old. Adherence to Mediterranean diet was assessed through a diet-score that was based on a validated food-frequency questionnaire. Blood pressure was measured and also fasting glucose, insulin and blood lipids. Insulin sensitivity was also assessed by the homeostasis model assessment (HOMA approach (glucose × insulin/22.5. Results Individuals with excess bodyweight in the highest tertile of diet score, were more insulin sensitive than those in the lowest tertile (11.4% lower HOMA, p = 0.06, had 13% lower levels of total cholesterol (p = 0.001 and 3 mmHg decrease of systolic blood pressure levels (p Conclusion Adherence to Mediterranean diet is modeslty associated with a better insulin sensitivity, lower levels of total cholesterol and lower levels of systolic blood pressure in overweight and obese subjects. This may suggest that compared to general population, the beneficial effect of this diet in cardiovascular system of excess body weight people is limited.

Design optimum frac jobs using virtual intelligence techniques

Energy Technology Data Exchange (ETDEWEB)

Shahab Mohaghegh; Andrei Popa; Sam Ameri [West Virginia University, Morgantown, WV (United States). Petroleum and Natural Gas Engineering

2000-10-01

Designing optimal frac jobs is a complex and time-consuming process. It usually involves the use of a two- or three-dimensional computer model. For the computer models to perform as intended, a wealth of input data is required. The input data includes wellbore configuration and reservoir characteristics such as porosity, permeability, stress and thickness profiles of the pay layers as well as the overburden layers. Among other essential information required for the design process is fracturing fluid type and volume, proppant type and volume, injection rate, proppant concentration and frac job schedule. Some of the parameters such as fluid and proppant types have discrete possible choices. Other parameters such as fluid and proppant volume, on the other hand, assume values from within a range of minimum and maximum values. A potential frac design for a particular pay zone is a combination of all of these parameters. Finding the optimum combination is not a trivial process. It usually requires an experienced engineer and a considerable amount of time to tune the parameters in order to achieve desirable outcome. This paper introduces a new methodology that integrates two virtual intelligence techniques, namely, artificial neural networks and genetic algorithms to automate and simplify the optimum frac job design process. This methodology requires little input from the engineer beyond the reservoir characterizations and wellbore configuration. The software tool that has been developed based on this methodology uses the reservoir characteristics and an optimization criteria indicated by the engineer, for example a certain propped frac length, and provides the detail of the optimum frac design that will result in the specified criteria. An ensemble of neural networks is trained to mimic the two- or three-dimensional frac simulator. Once successfully trained, these networks are capable of providing instantaneous results in response to any set of input parameters. These

Design optimum frac jobs using virtual intelligence techniques

Science.gov (United States)

Mohaghegh, Shahab; Popa, Andrei; Ameri, Sam

2000-10-01

Designing optimal frac jobs is a complex and time-consuming process. It usually involves the use of a two- or three-dimensional computer model. For the computer models to perform as intended, a wealth of input data is required. The input data includes wellbore configuration and reservoir characteristics such as porosity, permeability, stress and thickness profiles of the pay layers as well as the overburden layers. Among other essential information required for the design process is fracturing fluid type and volume, proppant type and volume, injection rate, proppant concentration and frac job schedule. Some of the parameters such as fluid and proppant types have discrete possible choices. Other parameters such as fluid and proppant volume, on the other hand, assume values from within a range of minimum and maximum values. A potential frac design for a particular pay zone is a combination of all of these parameters. Finding the optimum combination is not a trivial process. It usually requires an experienced engineer and a considerable amount of time to tune the parameters in order to achieve desirable outcome. This paper introduces a new methodology that integrates two virtual intelligence techniques, namely, artificial neural networks and genetic algorithms to automate and simplify the optimum frac job design process. This methodology requires little input from the engineer beyond the reservoir characterizations and wellbore configuration. The software tool that has been developed based on this methodology uses the reservoir characteristics and an optimization criteria indicated by the engineer, for example a certain propped frac length, and provides the detail of the optimum frac design that will result in the specified criteria. An ensemble of neural networks is trained to mimic the two- or three-dimensional frac simulator. Once successfully trained, these networks are capable of providing instantaneous results in response to any set of input parameters. These

Optimum thermal design of microchannel heat sink with triangular reentrant cavities

International Nuclear Information System (INIS)

Xia Guodong; Chai Lei; Wang Haiyan; Zhou Mingzheng; Cui Zhenzhen

2011-01-01

The effect of geometric parameters on water flow and heat transfer characteristics in microchannel heat sink with triangular reentrant cavities is numerically investigated. A three-dimensional laminar flow model, consisting of Navier-Stokes equations and energy conservation equation, with the conjugate heat transfer between the silicon base and water taken into consideration is solved numerically. In order to find the optimum geometric parameters, four variables, representing the distance and geometry of the triangular reentrant cavity, are designed. It is found that the vortices in the triangular reentrant cavities lead to chaotic advection and can greatly enhance the convective fluid mixing. The thermal and hydraulic boundary layers are interrupted and the repeated developing flow enhances heat transfer in the constant cross-section segment. Furthermore, the effects of the four design variables on heat transfer augmentation and pressure drop penalty are investigated depending on different Reynolds numbers by using the simulated annealing method. Based on the thermal enhancement factor performance maps, the optimal geometric parameters are obtained in principle. - Research highlights: → The microchannels with different triangular reentrant cavities are numerically investigated. → The heat transfer enhancement attributes to fluid mixing and redeveloped thermal boundary layers. → The optimal distance and geometry of the triangular reentrant cavity are obtained in principle.

Computational methods for fracture mechanics analysis of pressurized-thermal-shock experiments

International Nuclear Information System (INIS)

Bass, B.R.; Bryan, R.H.; Bryson, J.W.; Merkle, J.G.

1984-01-01

Extensive computational analyses are required to determine material parameters and optimum pressure-temperature transients compatible with proposed pressurized-thermal-shock (PTS) test scenarios and with the capabilities of the PTS test facility at the Oak Ridge National Laboratory (ORNL). Computational economy has led to the application of techniques suitable for parametric studies involving the analysis of a large number of transients. These techniques, which include analysis capability for two- and three-dimensional (2-D and 3-D) superposition, inelastic ligament stability, and upper-shelf arrest, have been incorporated into the OCA/USA computer program. Features of the OCA/USA program are discussed, including applications to the PTS test configuration

Computational methods for fracture mechanics analysis of pressurized-thermal-shock experiments

International Nuclear Information System (INIS)

Bass, B.R.; Bryan, R.H.; Bryson, J.W.; Merkle, J.G.

1984-01-01

Extensive computational analyses are required to determine material parameters and optimum pressure-temperature transients compatible with proposed pressurized-thermal-shock (PTS) test scenarios and with the capabilities of the PTS test facility at the Oak Ridge National Laboratory (ORNL). Computational economy has led to the application of techniques suitable for parametric studies involving the analysis of a large number of transients. These techniques, which include analysis capability for two- and three-dimensional (2-D and 3-D) superposition, inelastic ligament stability, and upper-shelf arrest, have been incorporated into the OCA/ USA computer program. Features of the OCA/USA program are discussed, including applications to the PTS test configuration. (author)

Phenomenological uncertainty analysis of containment building pressure load caused by severe accident sequences

International Nuclear Information System (INIS)

Park, S.Y.; Ahn, K.I.

2014-01-01

Highlights: • Phenomenological uncertainty analysis has been applied to level 2 PSA. • The methodology provides an alternative to simple deterministic analyses and sensitivity studies. • A realistic evaluation provides a more complete characterization of risks. • Uncertain parameters of MAAP code for the early containment failure were identified. - Abstract: This paper illustrates an application of a severe accident analysis code, MAAP, to the uncertainty evaluation of early containment failure scenarios employed in the containment event tree (CET) model of a reference plant. An uncertainty analysis of containment pressure behavior during severe accidents has been performed for an optimum assessment of an early containment failure model. The present application is mainly focused on determining an estimate of the containment building pressure load caused by severe accident sequences of a nuclear power plant. Key modeling parameters and phenomenological models employed for the present uncertainty analysis are closely related to the in-vessel hydrogen generation, direct containment heating, and gas combustion. The basic approach of this methodology is to (1) develop severe accident scenarios for which containment pressure loads should be performed based on a level 2 PSA, (2) identify severe accident phenomena relevant to an early containment failure, (3) identify the MAAP input parameters, sensitivity coefficients, and modeling options that describe or influence the early containment failure phenomena, (4) prescribe the likelihood descriptions of the potential range of these parameters, and (5) evaluate the code predictions using a number of random combinations of parameter inputs sampled from the likelihood distributions

Fructose containing sugars do not raise blood pressure or uric acid at normal levels of human consumption.

Science.gov (United States)

Angelopoulos, Theodore J; Lowndes, Joshua; Sinnett, Stephanie; Rippe, James M

2015-02-01

The impact of fructose, commonly consumed with sugars by humans, on blood pressure and uric acid has yet to be defined. A total of 267 weight-stable participants drank sugar-sweetened milk every day for 10 weeks as part of their usual, mixed-nutrient diet. Groups 1 and 2 had 9% estimated caloric intake from fructose or glucose, respectively, added to milk. Groups 3 and 4 had 18% of estimated caloric intake from high fructose corn syrup or sucrose, respectively, added to the milk. Blood pressure and uric acid were determined prior to and after the 10-week intervention. There was no effect of sugar type on either blood pressure or uric acid (interaction P>.05), and a significant time effect for blood pressure was noted (Pfructose at the 50th percentile level, whether consumed as pure fructose or with fructose-glucose-containing sugars, does not promote hyperuricemia or increase blood pressure. © 2014 Wiley Periodicals, Inc.

Variability of temperature, evaporation, insolation and sea level pressure in East Malaysia

International Nuclear Information System (INIS)

Camerlengo, A.L.; Mohd Nasir Saadon; Lim You Rang; Nhakhorn Somchit; Mohd Mahatir Osman

1999-01-01

The interrelation between global warming and certain meteorological parameters - temperature, evaporation, sea level pressure and isolation (hours of sunshine) - in East Malaysia is addressed in this study. The inter-annual climatic variability mainly due to ENSO warm events, is also investigated. The study of the monthly distribution of both evaporation and insolation in East Malaysia (i.e., the Malaysian states of Sabah and Sarawak, both of them situated in the northern part of the island of Borneo) is also covered in this paper (author)

Optimum Assembly Sequence Planning System Using Discrete Artificial Bee Colony Algorithm

Directory of Open Access Journals (Sweden)

Özkan Özmen

2018-01-01

Full Text Available Assembly refers both to the process of combining parts to create a structure and to the product resulting therefrom. The complexity of this process increases with the number of pieces in the assembly. This paper presents the assembly planning system design (APSD program, a computer program developed based on a matrix-based approach and the discrete artificial bee colony (DABC algorithm, which determines the optimum assembly sequence among numerous feasible assembly sequences (FAS. Specifically, the assembly sequences of three-dimensional (3D parts prepared in the computer-aided design (CAD software AutoCAD are first coded using the matrix-based methodology and the resulting FAS are assessed and the optimum assembly sequence is selected according to the assembly time optimisation criterion using DABC. The results of comparison of the performance of the proposed method with other methods proposed in the literature verify its superiority in finding the sequence with the lowest overall time. Further, examination of the results of application of APSD to assemblies consisting of parts in different numbers and shapes shows that it can select the optimum sequence from among hundreds of FAS.

Correction ofvitamin D deficiency/insufficiency and assessment of 24-hour blood pressure parameters in perimenopausal women with arterial hypertension

Directory of Open Access Journals (Sweden)

Ludmiła Walerjewna Jankowska

2014-09-01

Full Text Available Both arterial hypertension and vitamin D deficiency are highly prevalent in the general population. Aim of the study was to assess blood pressure and its dynamics in 24-hour ambulatory blood pressure monitoring (ABPM while correcting the vitamin D deficiency/insufficiency in perimenopausal women, who have grade 2 arterial hypertension. Material and methods: The study group consisted of 50 premenopausal women [48 (45–50 years] and 52 women in early (up to 5 years postmenopausal period [52 (50–54 years]. Total 25-(OHD blood plasma levels were assessed by immunoenzyme assay using DRG kit (Marburg, Germany. The total 25-(OHD blood plasma levels below 20 ng/ml were considered as vitamin D insufficiency, the concentration of 20–30 ng/ml – as deficiency, and the levels 30–60 ng/ml were considered normal. In the group of women with 25-(OHD deficiency/insufficiency two subgroups were isolated: IB subgroup (n = 25 and IIB (n = 21, which were introduced with treatment algorithm, including cholecalciferol administration at a daily dose of 2000 IU for 3 months. Results: Cholecalciferol therapy at a dose of 2000 IU per day for a period of 3 months has allowed reaching the optimum concentration of vitamin D in 80% of premenopausal hypertensive women, and in 76.2% of women in the early postmenopausal period. Correction of plasma vitamin D deficiency achieved by taking cholecalciferol, while using combined antihypertensive therapy (ramipril + indapamide allows to improve the following parameters assessed in ambulatory blood pressure monitoring in premenopausal women: the mean daytime and nighttime systolic blood pressure, time index of 24-hour and daytime systolic blood pressure, nighttime blood pressure variability, systolic and diastolic blood pressure morning surge, and normalization of nighttime:daytime blood pressure ratio; in postmenopausal women the treatment allowed: the reduction of morning surge of

Calculation of optimum control rod operation programme for boiling water reactor

International Nuclear Information System (INIS)

Fehr, L.

1978-01-01

Control rod operation programmes are calculated based on a three dimensional Boiling Water Reactor situation model. The position of the control rods at variosu burn-ups is chosen by an optimisation so that the sum of the square deviations of the load density distribution from an optimum distribution ('Haling' distribution) are minimised. Other conditions are remaining critical and observing the thermal limits for central fuel element melting and critical heat surface loading. As an example, an optimum control rod operation programme for the first cycle in Lengen nuclear power station is calculated and is compared with the programme actually used. (orig.) 891 HP [de

The Dependency between the Arabian Peninsula Wet Events and Sea Level Pressure Patterns during Spring Season

KAUST Repository

El Kenawy, Ahmed M.; McCabe, Matthew; Stenchikov, Georgiy L.; Raj, Jerry

2014-01-01

This work investigates the relationships between regional extreme wet events in the Arabian Peninsula during the spring season (MAM) and sea level pressure (SLP) patterns. Based on NCEP/NCAR reanalysis data, S-mode principal components were computed

Applicability Problem in Optimum Reinforced Concrete Structures Design

Directory of Open Access Journals (Sweden)

Ashara Assedeq

2016-01-01

Full Text Available Optimum reinforced concrete structures design is very complex problem, not only considering exactness of calculus but also because of questionable applicability of existing methods in practice. This paper presents the main theoretical mathematical and physical features of the problem formulation as well as the review and analysis of existing methods and solutions considering their exactness and applicability.

Effects of exogenous growth regulators on cell suspension culture of yin-hong grape (vitis vinifera l.) and establishment of the optimum medium

International Nuclear Information System (INIS)

Chao, Y.; Feng, J.C.; Yan, W.Y.; Xiao, Y.; Jun, Y.Y

2015-01-01

Callus induced by stem of Yin-hong grape (Vitis vinifera L.) was used as materials and B5 medium as basic medium. The major growth parameters of cell suspension cultures with various levels of 1-Naphthaleneacetic acid (NAA) and 6-Benzyl aminopurine (6-BA) were investigated to provide a basis for the optimum medium of suspension cell cultures of Yin-hong grape regarding cell number, packed cell volume (PCV), dry cell weight (DCW), cell viability, and morphology. All data were analysed by of two-way analysis of variance (ANOVA). Results showed that the treatment of 6-BA and NAA would effect the cell growth dynamics, probably causing logarithmic phase in advance at higher levels of 6-BA. Different concentration of 6-BA and NAA had significant effects on cells number, PCV, DCW and viability (p<0.05), while no-significant effect was observed on the cells morphology. The optimum medium for suspension cell cultures of Yin-hong grape was identified as B5+1.5 mg/L6-BA+1.5 mg/LNAA+ 250 mg/L casein hydrolysate + 30 g/L sucrose. With the optimum medium, the maximum number of suspension cells after the logarithmic growth phase was 34.78 * 108 / mL, the highest cell viability reached 86.45%.; DCW reached 3.84 g/L and PCV reached 0.092 mL/mL after eight days cultivating. (author)

Analysis of the Optimum Usage of Slag for the Compressive Strength of Concrete.

Science.gov (United States)

Lee, Han-Seung; Wang, Xiao-Yong; Zhang, Li-Na; Koh, Kyung-Taek

2015-03-18

Ground granulated blast furnace slag is widely used as a mineral admixture to replace partial Portland cement in the concrete industry. As the amount of slag increases, the late-age compressive strength of concrete mixtures increases. However, after an optimum point, any further increase in slag does not improve the late-age compressive strength. This optimum replacement ratio of slag is a crucial factor for its efficient use in the concrete industry. This paper proposes a numerical procedure to analyze the optimum usage of slag for the compressive strength of concrete. This numerical procedure starts with a blended hydration model that simulates cement hydration, slag reaction, and interactions between cement hydration and slag reaction. The amount of calcium silicate hydrate (CSH) is calculated considering the contributions from cement hydration and slag reaction. Then, by using the CSH contents, the compressive strength of the slag-blended concrete is evaluated. Finally, based on the parameter analysis of the compressive strength development of concrete with different slag inclusions, the optimum usage of slag in concrete mixtures is determined to be approximately 40% of the total binder content. The proposed model is verified through experimental results of the compressive strength of slag-blended concrete with different water-to-binder ratios and different slag inclusions.

Optimum Remediation Conditions of Vertical Electrokinetic-Flushing Equipment to Decontaminate a Radioactive Soil

International Nuclear Information System (INIS)

Kim, Gye Nam; Yang, Byeong IL; Moon, Jei Kwon; Lee, Kune Woo

2009-01-01

Vertical electrokintic-flushing remediation equipment was developed for the remediation of a radioactive soil near nuclear facilities. An optimum reagent was selected to decontaminate the radioactive soil near nuclear facilities with the developed vertical electrokintic-flushing remediation equipment, and the optimum remediation conditions were established to obtain a higher remediation efficiency. Namely, acetic acid was selected as an optimum reagent due to its higher remediation efficiency. When the electrokinetic remediation and the electrokinetic-flushing remediation results were compared, the removal efficiency of 4.6% and the soil waste solution volume of 1.5 times were increased in the electrokinetic remediation. When the potential gradient within an electrokinetic soil cell was increased by two times (4.0 V/cm), the removal efficiencies of Co 2+ and Cs + were increased by about 4.3%( Co 2+ : 98.9%, Cs + : 96.7%). Also, when the reagent concentration was increased from 0.01 M to 0.05 M, the removal efficiency of Co 2+ was increased but that of Cs + was decreased. Therefore, the optimum remediation conditions were that the acetic concentration was 0.01 M ∼ 0.05 M, the potential gradient was 4 V/cm, the injection of reagent 2.4 ml/g, and the remediation period was 20 days.

Simulation of Spray Injection in the Pressurizer Using RELAP5

Directory of Open Access Journals (Sweden)

S. Dibyo

2017-08-01

Full Text Available A modeling research using Relap5 to assess the pressurizer of a pressurized water reactor(PWR power plant has been performed. The heater and water injection systems in the pressurizer system of the PWRare of greatimportance for system pressure control.The heater is designed to increase the pressure while the water sprayer injection is to perform depressurization. Most of studies conducted in the past mainly focused on determining the effects of nozzle spray design and droplet size using testing loops. The purpose of this simulation is to analyze the spray injection flow rate against the pressure characteristics of the pressurizer using RELAP5. Through this approach, the optimum injection flow rate of full scale plant pressurizer can be analyzed. The parameters investigated are pressure and temperature.In RELAP5, the pressurizer tank wasmodeled with six volume nodes and the heater was modeled by using heat structure. In the model, the sprayer takes water from the cold leg to inject it into the top of tank region.The resultsshowedthat the mass flow of about 4 kg/s is the mosteffectivevalueto limit pressure in the pressurizer to below 15.7 MPa. However, the flow rates of 8 kg/s and more cause overpressure. This simulation is usefulto complement the data related to the water flow rate injection systems of the pressurizer. Normal 0 false false false EN-US X-NONE X-NONE Maternal age during pregnancy is associated with third trimester blood pressure level: the generation R study.

Science.gov (United States)

Gaillard, Romy; Bakker, Rachel; Steegers, Eric A P; Hofman, Albert; Jaddoe, Vincent W V

2011-09-01

We hypothesized that hemodynamic adaptations related to pregnancy and ageing might be associated with differences in blood pressure levels during pregnancy between younger and older women. This might partly explain the increased risk of gestational hypertensive disorders with advanced maternal age. We examined the associations of maternal age with systolic and diastolic blood pressure in each trimester of pregnancy and the risks of gestational hypertensive disorders. The study was conducted among 8,623 women participating in a population-based prospective cohort study from early pregnancy onwards. Age was assessed at enrolment. Blood pressure was measured in each trimester. Information about gestational hypertensive disorders was available from medical records. In second and third trimester, older maternal age was associated with lower systolic blood pressure (-0.9 mm Hg (95% confidence interval: -1.4, -0.3) and -0.6 mm Hg (95% confidence interval: -1.1, -0.02) per additional 10 maternal years, respectively). Older maternal age was associated with higher third trimester diastolic blood pressure (0.5 mm Hg (95% confidence interval: 0.04, 0.9) per additional 10 maternal years). Maternal age was associated with pregnancy-induced hypertension among overweight and obese women. Older maternal age is associated with lower second and third trimester systolic blood pressure, but higher third trimester diastolic blood pressure. These blood pressure differences seem to be small and within the physiological range. Maternal age is not consistently associated with the risks of gestational hypertensive disorders. Maternal body mass index might influence the association between maternal age and the risk of pregnancy-induced hypertension.

Optimum body size of Holstein replacement heifers.

Science.gov (United States)

Hoffman, P C

1997-03-01

Criteria that define optimum body size of replacement heifers are required by commercial dairy producers to evaluate replacement heifer management programs. Historically recommended body size criteria have been based on live BW measurements. Numerous research studies have observed a positive relationship between BW at first calving and first lactation milk yield, which has served as the impetus for using live BW to define body size of replacement heifers. Live BW is, however, not the only available measurement to define body size. Skeletal measurements such as wither height, length, and pelvic area have been demonstrated to be related to first lactation performance and (or) dystocia. Live BW measurements also do not define differences in body composition. Differences in body composition of replacement heifers at first calving are also related to key performance variables. An updated research data base is available for the modern Holstein genotype to incorporate measures of skeletal growth and body composition with BW when defining body size. These research projects also lend insight into the relative importance of measurements that define body size of replacement heifers. Incorporation of these measurements from current research into present BW recommendations should aid commercial dairy producers to better define replacement heifer growth and management practices. This article proposes enhancements in defining optimum body size and growth characteristics of Holstein replacement heifers.

The effect of positive end-expiratory pressure on pulse pressure ...

African Journals Online (AJOL)

The effect of positive end-expiratory pressure on pulse pressure variation. FJ Smith, M Geyser, I Schreuder, PJ Becker. Abstract. Objectives: To determine the effect of different levels of positive end-expiratory pressure (PEEP) on pulse pressure variation (PPV). Design: An observational study. Setting: Operating theatres of a ...

Acute-Phase Blood Pressure Levels Correlate With a High Risk of Recurrent Strokes in Young-Onset Ischemic Stroke.

Science.gov (United States)

Mustanoja, Satu; Putaala, Jukka; Gordin, Daniel; Tulkki, Lauri; Aarnio, Karoliina; Pirinen, Jani; Surakka, Ida; Sinisalo, Juha; Lehto, Mika; Tatlisumak, Turgut

2016-06-01

High blood pressure (BP) in acute stroke has been associated with a poor outcome; however, this has not been evaluated in young adults. The relationship between BP and long-term outcome was assessed in 1004 consecutive young, first-ever ischemic stroke patients aged 15 to 49 years enrolled in the Helsinki Young Stroke Registry. BP parameters included systolic (SBP) and diastolic BP, pulse pressure, and mean arterial pressure at admission and 24 hours. The primary outcome measure was recurrent stroke in the long-term follow-up. Adjusted for demographics and preexisting comorbidities, Cox regression models were used to assess independent BP parameters associated with outcome. Of our patients (63% male), 393 patients (39%) had prestroke hypertension and 358 (36%) used antihypertensive treatment. The median follow-up period was 8.9 years (interquartile range 5.7-13.2). Patients with a recurrent stroke (n=142, 14%) had significantly higher admission SBP, diastolic BP, pulse pressure, and mean arterial pressure (Pstroke. Patients with SBP ≥160 mm Hg compared with those with SBP strokes (hazard ratio 3.3 [95% confidence interval, 2.05-4.55]; Pstroke, while the 24-hour BP levels were not. In young ischemic stroke patients, high acute phase BP levels are independently associated with a high risk of recurrent strokes. © 2016 American Heart Association, Inc.

Optimum Er concentration for in situ doped GaN visible and infrared luminescence

International Nuclear Information System (INIS)

Lee, D. S.; Heikenfeld, J.; Steckl, A. J.; Hommerich, U.; Seo, J. T.; Braud, A.; Zavada, J.

2001-01-01

GaN thin films have been doped with varying Er concentrations (0.01--10 at.%) during molecular-beam-epitaxy growth. As expected, the visible and infrared (IR) emissions, from photoluminescence (PL) and electroluminescence (EL), are a strong function of Er concentration. We report on the determination of an optimum Er doping level for PL and EL intensity. Secondary ion mass spectroscopy and Rutherford backscattering measurements showed that the Er concentration in GaN increased exponentially with Er cell temperature. PL and EL intensity of green emission at 537 and 558 nm, due to Er 4f--4f inner shell transitions, exhibited a maximum at ∼1 at.% Er. IR PL intensity at 1.54 μm, due to another Er transition, revealed the same maximum for ∼1 at.% Er concentration. PL lifetime measurements at 537 nm showed that samples with Er concentration <1 at.% had a lifetime of ∼5 μs. For Er concentration ≥1 at.%, the lifetime decreased rapidly to values below 1 μs. This concentration quenching is believed to be due to a combination of Er cross relaxation and energy transfer to GaN defects, eventually followed by precipitation. This conclusion is supported by x-ray diffraction measurements. As a result, we have determined that the optimum Er doping concentration into GaN is ∼1 at.%. Copyright 2001 American Institute of Physics

Investigation of gene expression and serum levels of PIN1 and eNOS with high blood pressure in patients with Alzheimer disease.

Science.gov (United States)

Azimi, Mina; Nikanfar, Masoud; Khakikhatibi, Fatemeh; Rahbarghazi, Reza; Nourazarian, Seyed Manuchehr; Biray Avci, Cigir; Nourazarian, Alireza

2017-09-01

According to evidence, Alzheimer's disease is known as one of the most serious neurodegenerative diseases, for which hypertension has been observed to be a key risk factor. Therefore, this study aims to examine the relationship between the PIN1 and eNOS genes expression, as well as serum levels and hypertension in Alzheimer's disease sufferers. Blood samples were obtained from subjects who were divided into four groups: the control group, normotensive Alzheimer's patients, the Alzheimer's sufferers group with hypertension, and the healthy group with only hypertension, considering the inhibition of confounding factors. Thereafter, eNOS and PIN1 genes expression along with serum levels were studied. Based on the obtained results, a statistically significant correlation didn't exist between serum level of PIN1 and the systolic and diastolic blood pressure, between serum level of eNOS and diastolic blood pressure in the norm tension Alzheimer's disease patients, between serum levels of PIN1, eNOS and systolic blood pressure, and between serum eNOS and systolic and diastolic blood pressure in the patients with hypertension (pdiseases in Alzheimer's disease. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bud initiation and optimum harvest date in Brussels sprouts

NARCIS (Netherlands)

Everaarts, A.P.; Sukkel, W.

1999-01-01

For six cultivars of Brussels sprouts (Brassica oleracea var. gemmifera) with a decreasing degree of earliness, or optimum harvest date, the time of bud initiation was determined during two seasons. Fifty percent of the plants had initiated buds between 60 and 75 days after planting (DAP) in 1994

Economics of finishing Tanzania Shorthorn Zebu cattle in feedlot and optimum finishing period

DEFF Research Database (Denmark)

Asimwe, L.; Kimambo, A E; Laswai, G. H.

2016-01-01

finishing for TSZ cattle. The biological data collected from the two experiments were used as basis for deriving the economic scenarios. The range of days steers were kept in feedlot was set at 0, 25, 50, 75 and 100 days. The dietary metabolisable energy intake (MEI) levels used in the study were 55 MJ......Economic potential of finishing Tanzania Shorthorn Zebu (TSZ) cattle in feedlot was analysed using data obtained from two feedlot experiments carried out at Kongwa ranch in Tanzania. The experiments were performed to evaluate the effects of feeding agro-processing by products and length of feedlot...... length of 25 days, higher profit per animal carcass was realized with long stays (100 days, 238,000 TSh.) than short stays (25 days, 37,600 TSh.). It was concluded that the high feeding level is the most profitable irrespective of meat price and finishing length. The optimum finishing length is between...

[LEVELS OF OBESITY, METABOLIC PROFILE, CONSUMPTION OF TABACO AND BLOOD PRESSURE IN SEDENTARY YOUTHS].

Science.gov (United States)

Caamaño Navarrete, Felipe; Alarcón Hormazábal, Manuel; Delgado Floody, Pedro

2015-11-01

in Chile, the National Health Survey (ENS) conducted in 2009-2010 reported high prevalence of overweight, sedentary lifestyle, high cholesterol and metabolic syndrome in the population. to determine the prevalence in young sedentary obesity and consumption of tabaco and analyze their association with the metabolic profile, body fat percentage and blood pressure. 125 young sedentary, 26 men and 99 women, aged between 17 and 29 years old were evaluated. Body mass index (BMI), percent body fat (% fat), waist contour (CC), systolic and diastolic blood pressure, total cholesterol, HDL cholesterol (HDL-C), LDL cholesterol (LDL-C), triglycerides: measurements were performed, glycemia and consumption of snuff. HDL-C (p = 0.000) and% MG (p = 0.043) were higher in women. 37.6% of young people turned smoker. 35, 2% of the sample showed excessive malnutrition. Obese subjects had higher levels: waist contour (p = 0.000) and% FM (p = 0.000). When analyzing obesity DC, this showed significant differences in BMI,% fat, systolic and diastolic blood pressure. BMI presented positive association with CC,% fat, total cholesterol, triglycerides, LDL, systolic and diastolic blood pressure (p tabaco in the study sample, while other variables are not high-risk categories, it is an opportune time to intervene and reverse these negative health trends now. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

On the optimum signal constellation design for high-speed optical transport networks.

Science.gov (United States)

Liu, Tao; Djordjevic, Ivan B

2012-08-27

In this paper, we first describe an optimum signal constellation design algorithm, which is optimum in MMSE-sense, called MMSE-OSCD, for channel capacity achieving source distribution. Secondly, we introduce a feedback channel capacity inspired optimum signal constellation design (FCC-OSCD) to further improve the performance of MMSE-OSCD, inspired by the fact that feedback channel capacity is higher than that of systems without feedback. The constellations obtained by FCC-OSCD are, however, OSNR dependent. The optimization is jointly performed together with regular quasi-cyclic low-density parity-check (LDPC) code design. Such obtained coded-modulation scheme, in combination with polarization-multiplexing, is suitable as both 400 Gb/s and multi-Tb/s optical transport enabling technology. Using large girth LDPC code, we demonstrate by Monte Carlo simulations that a 32-ary signal constellation, obtained by FCC-OSCD, outperforms previously proposed optimized 32-ary CIPQ signal constellation by 0.8 dB at BER of 10(-7). On the other hand, the LDPC-coded 16-ary FCC-OSCD outperforms 16-QAM by 1.15 dB at the same BER.

Effect of Low Pressure End Conditions on Steam Power Plant Performance

Directory of Open Access Journals (Sweden)

Ali Syed Haider

2014-07-01

Full Text Available Most of the electricity produced throughout the world today is from steam power plants and improving the performance of power plants is crucial to minimize the greenhouse gas emissions and fuel consumption. Energy efficiency of a thermal power plant strongly depends on its boiler-condenser operating conditions. The low pressure end conditions of a condenser have influence on the power output, steam consumption and efficiency of a plant. Hence, the objective this paper is to study the effect of the low pressure end conditions on a steam power plant performance. For the study each component was modelled thermodynamically. Simulation was done and the results showed that performance of the condenser is highly a function of its pressure which in turn depends on the flow rate and temperature of the cooling water. Furthermore, when the condenser pressure increases both net power output and plant efficiency decrease whereas the steam consumption increases. The results can be used to run a steam power cycle at optimum conditions.

Optimum sizing of wind-battery systems incorporating resource uncertainty

International Nuclear Information System (INIS)

Roy, Anindita; Kedare, Shireesh B.; Bandyopadhyay, Santanu

2010-01-01

The inherent uncertainty of the wind is a major impediment for successful implementation of wind based power generation technology. A methodology has been proposed in this paper to incorporate wind speed uncertainty in sizing wind-battery system for isolated applications. The uncertainty associated with the wind speed is incorporated using chance constraint programming approach. For a pre-specified reliability requirement, a deterministic equivalent energy balance equation may be derived from the chance constraint that allows time series simulation of the entire system. This results in a generation of the entire set of feasible design options, satisfying different system level constraints, on a battery capacity vs. generator rating diagram, also known as the design space. The proposed methodology highlights the trade-offs between the wind turbine rating, rotor diameter and the battery size for a given reliability of power supply. The optimum configuration is chosen on the basis of the minimum cost of energy (US$/kWh). It is shown with the help of illustrative examples that the proposed methodology is generic and flexible to incorporate alternate sub-component models. (author)

Fitness Level Modulates Intraocular Pressure Responses to Strength Exercises.

Science.gov (United States)

Vera, Jesús; Jiménez, Raimundo; Redondo, Beatríz; Cárdenas, David; García-Ramos, Amador

2018-06-01

Purpose/Aim: The execution of strength exercises has demonstrated to increase the intraocular pressure (IOP) levels, and it may have a negative impact on the ocular health. We aimed to explore the influence of fitness level on the acute IOP response to strength exercises performed under different loading conditions, as well as to test whether the IOP responses differ between the bench press and jump squat when performed against the same relative loads. Forty military personnel males were divided in two subgroups (20 high-fit and 20 low-fit) based on their relative to body mass one-repetition maximum (1-RM). Participants performed an incremental loading test in the bench press and jump squat exercises, and IOP was assessed before and after each repetition by rebound tonometry. IOP increased immediately after executing both exercises (p e., high-fit and low-fit) and in both exercises (R 2 range: 0.81-1.00). Higher fitness level attenuated the IOP rise produced by both exercises (p < 0.01 in both cases). The bench press induced higher IOP increments than the jump squat for both groups at relative loads of ~50%1-RM and ~60%1-RM (p < 0.01 in all cases). These data indicate that IOP increases as a consequence of performing strength exercises, being the increment accentuated with the increase of the load and in the bench press compared to the jump squat exercise. Of special importance would be that the IOP responses were significantly reduced in high-fit individuals. These findings should be addressed in glaucoma patients.

Change in optimum genetic algorithm solution with changing band discontinuities and band widths of electrically conducting copolymers

Science.gov (United States)

Kaur, Avneet; Bakhshi, A. K.

2010-04-01

The interest in copolymers stems from the fact that they present interesting electronic and optical properties leading to a variety of technological applications. In order to get a suitable copolymer for a specific application, genetic algorithm (GA) along with negative factor counting (NFC) method has recently been used. In this paper, we study the effect of change in the ratio of conduction band discontinuity to valence band discontinuity (Δ Ec/Δ Ev) on the optimum solution obtained from GA for model binary copolymers. The effect of varying bandwidths on the optimum GA solution is also investigated. The obtained results show that the optimum solution changes with varying parameters like band discontinuity and band width of constituent homopolymers. As the ratio Δ Ec/Δ Ev increases, band gap of optimum solution decreases. With increasing band widths of constituent homopolymers, the optimum solution tends to be dependent on the component with higher band gap.

Optimum principle for a vehicular traffic network: minimum probability of congestion

International Nuclear Information System (INIS)

Kerner, Boris S

2011-01-01

We introduce an optimum principle for a vehicular traffic network with road bottlenecks. This network breakdown minimization (BM) principle states that the network optimum is reached when link flow rates are assigned in the network in such a way that the probability for spontaneous occurrence of traffic breakdown in at least one of the network bottlenecks during a given observation time reaches the minimum possible value. Based on numerical simulations with a stochastic three-phase traffic flow model, we show that in comparison to the well-known Wardrop's principles, the application of the BM principle permits considerably greater network inflow rates at which no traffic breakdown occurs and, therefore, free flow remains in the whole network. (fast track communication)

Thermal characteristic of insulation for optimum design of RI transport package

International Nuclear Information System (INIS)

Lee, J. C.; Bang, K. S.; Seo, K. S.

2002-01-01

A package to transport the high level radioactive materials in required to withstand the hypothetical accident conditions as well as normal transport conditions according to IAEA and domestic regulations. The regulations require that the package should maintain the shielding, thermal and structural integrities to release no radioactive material. Thermal characteristics of insulations were evaluated and optimum insulation thickness was deduced for RI transport package. The package has a maximum capacity of 600 Curies for Ir-192 sealed source. The insulation thickness was decided with 10 mm of polyurethane form to maintain the thermal safety under fire accident condition. Thermal analysis was carried out for RI transport package, and it was shown that the thermal integrity of the package was maintained. The results obtained this study will be applied to a basic data for design of RI transport cask

Evaluation of Blood Pressure Control Levels and Treatment Compliances of Hypertensive Patients

Directory of Open Access Journals (Sweden)

Cenk Aypak

2013-04-01

Full Text Available Purpose: The aim of the study is to evaluate the knowledge of patients about hypertension (HT, compliance with lifestyle changes and to determine their blood pressure levels under antihypertensive therapy. Method: Hypertensive patients that applied to Family medicine outpatient clinics of Diskapi Yildirim Beyazit Education and Research Hospital for the first time, in 2012 (between February 1 to April 30, were included in our cross-sectional study. Patients are evaluated primarily for the control and the factors that can affect high blood pressure and the rate on achieving treatment goals. Results: Three hundred and forty patients were included in the study. The mean age of the patients was 60.5±10.7 years and 222 of them (65.3% were female. The blood pressure was not under control in 108 (31.8% patients. The mean body weight of male patients was statistically higher than females (p=0.015. The number of the patients that knew the normal blood pressure value was 249 (73.2%. Among those 155 (62.2% were women and 179 (71.9% were younger than 65 years of age (p=0.0001. Forty one patients (12.1% were still smoking, 46 (13.5% patients were exercising regularly and 32 (9.4% were consuming regular diet. Blood pressure was better controlled in the group that was exercising regularly (p=0.001. The rate of male patients that were on regular exercise and diet, were higher than females (p=0.09. Only 86 patients (25.3% knew the name of their antihypertensive medication and 65 of patients (19.1% knew the dose of their medication. Female patients knew the name of their medication better than males (p=0.002. 156 patients (45.9% were using two kinds of antihypertensive medication. 58 patients (17.1% were skipping doses a few times a week. Conclusion: The knowledge of hypertensive patients on their illness and their compliance on non-drug treatments were inadequate. The compliance of patients should be improved by development of patient-doctor should be improved

EXPERIMENTAL STUDY OF HIGH LEVELS OF SO2 REMOVAL IN ATMOSPHERIC-PRESSURE FUIDIZED-BED COMBUSTORS

Science.gov (United States)

The report describes tests conducted in an atmospheric-pressure-fluidized-bed combustor (FBC) with a cross-section of 1 x 1.6 m) to demonstrate high levels of S02 removal when burning a high-sulfur coal and feeding limestone sorbent for S02 removal. The goal was to achieve 90-plu...

Confidence interval of intrinsic optimum temperature estimated using thermodynamic SSI model

Institute of Scientific and Technical Information of China (English)

Takaya Ikemoto; Issei Kurahashi; Pei-Jian Shi

2013-01-01

The intrinsic optimum temperature for the development of ectotherms is one of the most important factors not only for their physiological processes but also for ecological and evolutional processes.The Sharpe-Schoolfield-Ikemoto (SSI) model succeeded in defining the temperature that can thermodynamically meet the condition that at a particular temperature the probability of an active enzyme reaching its maximum activity is realized.Previously,an algorithm was developed by Ikemoto (Tropical malaria does not mean hot environments.Journal of Medical Entomology,45,963-969) to estimate model parameters,but that program was computationally very time consuming.Now,investigators can use the SSI model more easily because a full automatic computer program was designed by Shi et al.(A modified program for estimating the parameters of the SSI model.Environmental Entomology,40,462-469).However,the statistical significance of the point estimate of the intrinsic optimum temperature for each ectotherm has not yet been determined.Here,we provided a new method for calculating the confidence interval of the estimated intrinsic optimum temperature by modifying the approximate bootstrap confidence intervals method.For this purpose,it was necessary to develop a new program for a faster estimation of the parameters in the SSI model,which we have also done.

The temporal distribution of directional gradients under selection for an optimum.

Science.gov (United States)

Chevin, Luis-Miguel; Haller, Benjamin C

2014-12-01

Temporal variation in phenotypic selection is often attributed to environmental change causing movements of the adaptive surface relating traits to fitness, but this connection is rarely established empirically. Fluctuating phenotypic selection can be measured by the variance and autocorrelation of directional selection gradients through time. However, the dynamics of these gradients depend not only on environmental changes altering the fitness surface, but also on evolution of the phenotypic distribution. Therefore, it is unclear to what extent variability in selection gradients can inform us about the underlying drivers of their fluctuations. To investigate this question, we derive the temporal distribution of directional gradients under selection for a phenotypic optimum that is either constant or fluctuates randomly in various ways in a finite population. Our analytical results, combined with population- and individual-based simulations, show that although some characteristic patterns can be distinguished, very different types of change in the optimum (including a constant optimum) can generate similar temporal distributions of selection gradients, making it difficult to infer the processes underlying apparent fluctuating selection. Analyzing changes in phenotype distributions together with changes in selection gradients should prove more useful for inferring the mechanisms underlying estimated fluctuating selection. © 2014 The Author(s). Evolution © 2014 The Society for the Study of Evolution.

Optimum Design of Heat Exchangers Networks Part -I: Software Development

International Nuclear Information System (INIS)

Gabr, E.M.A.; EI-Temtamy, S.A.; Deriasl, S.F.; Moustafa, H.A.

2004-01-01

In this paper, we have developed a computerized framework for Heat Exchanger Network Synthesis (HENS) with optimality conditions of achieving the least operating and capital cost. The framework of HEN design involves the development three-computer programs, which applied sequentially to design an optimum HEN. The first program Automatic Minimum Utilities [AMU] developed for automatic formulation of LP equations, these equations can be solved by the optimization software [LINDO] to predict minimum hot and cold utilities. The second program based on Vertical Heat Transfer Method [VHTM] for predicting minimum overall heat transfer area and defining the optimum δbT m in. The third program [Mod.RESHEX] developed for targeting of heat transfer area and automatic synthesis of HEN. This program represents the modifications and development of RESHEX method to overcome the design defects, which appeared on original RESHEX applications

Dual-pressure vaporization Kalina cycle for cascade reclaiming heat resource for power generation

International Nuclear Information System (INIS)

Guo, Zhanwei; Zhang, Zhi; Chen, Yaping; Wu, Jiafeng; Dong, Cong

2015-01-01

Graphical abstract: Schematic of the dual-pressure evaporation Kalina cycle. - Highlights: • Dual-pressure vaporization Kalina cycle for high-grade heat resource is investigated. • It is designed with 2nd evaporation branch for cascade utilization of heat resource. • Work and basic concentrations, dew point temperature of evaporation are optimized. • Power recovery efficiency of proposed cycle is 17% higher than that of Kalina cycle. • Dual-p vaporization Kalina cycle fits reclaiming heat resource higher than 350 °C. - Abstract: To further improve the cycle efficiency with the heat transfer curves between higher than 350 °C heat resource and the evaporating working medium of the Kalina cycle and to reduce the exhaust temperature of heat resource, the dual-pressure vaporization Kalina cycle for cascade utilization of high-to-mid grade heat resource is proposed. The optimization was conducted for parameters in this modified Kalina cycle such as concentrations of work solution and basic solution, evaporation dew point temperature. Under the conditions of inlet temperatures of heat resource and cooling water of respectively 400 °C and 25 °C and the constraints of proper heat transfer pinch point temperature differences, the maximum evaporation pressure not exceeds 20 MPa, the vapour quality at the turbine outlet is greater than 0.85 and the exhaust temperature of heat resource is not lower than 90 °C, the optimum parameters are obtained that the work and basic concentrations are 0.45 and 0.272 respectively, the dew point temperature of evaporation is 300 °C, and the corresponding power recovery efficiency of the dual-pressure vaporization Kalina cycle reaches 27%, which is 17% higher than that of the Kalina cycle with optimum parameters.

An analysis of the optimum operating point for a switched reluctance motor

International Nuclear Information System (INIS)

Mao, S.-H.; Tsai, M.-C.

2004-01-01

This paper proposes a simple method to determine the optimum exciting current, for high output torque in switched reluctance motors (SRMs). By modelling the flux-linkage with one curve at the unaligned position, and with two curves at the aligned position, the maximum increment of the co-energy and torque can be predicted accurately, and the optimum exciting current can also be determined. This easily implemented method is aimed at providing an index for determining the SRM exciting current. This will be useful for SRM designers in deciding the rated current and in obtaining the maximum motor efficiency

Differences in Blood Pressure and Vascular Responses Associated with Ambient Fine Particulate Matter Exposures Measured at the Personal Versus Community Level

Science.gov (United States)

Background Higher ambient fine particulate matter (PM2.5) levels can be associated with increased blood pressure and vascular dysfunction. Objectives To determine the differential effects on blood pressure and vascular function of daily changes in community ambient-...

Improved optimum condition for recovery and measurement of 210 ...

African Journals Online (AJOL)

The aim of this study was to determine the optimum conditions for deposition of 210Po and evaluate the accuracy and precision of the results for its determination in environmental samples. To improve the technique for measurement of polonium-210(210Po) in environmental samples. The optimization of five factors (volume ...

Studies of jet fuel additives using the quartz crystal microbalance and pressure monitoring at 140 C

Energy Technology Data Exchange (ETDEWEB)

Zabarnick, S.; Grinstead, R.R. [Univ. of Dayton Research Institute, OH (United States)

1995-05-01

The quartz crystal microbalance (QCM) and pressure monitoring are used for the evaluation of jet fuel additives for the improvement of jet fuel thermal stability. The mechanisms of additive behavior are determined by measuring the time dependent deposition with the QCM and oxidation by pressure measurements. Studies at various additive concentrations permits the determination of optimum additive concentrations. Additive packages made of mixtures of antioxidants, detergent/dispersants, and metal deactivators are shown to yield good improvements in thermal stability over a wide range of jet fuel types.

Choice of economical optimum blanket of hybrid reactors

Energy Technology Data Exchange (ETDEWEB)

Blinkin, V L; Novikov, V M

1981-01-01

The economical effectiveness of symbiotic power systems depends on the choice of the correlation between energy production and fissile fuel production in blankets of controlled thermonuclear fusion reactor (CTR), what is investigated here. It is shown that the optimum value of this correlation essentially depends on the ratio between the specific costs for energy production in hybrid thermonuclear reactors and that in fission reactors as part of the symbiotic system.

Including climate variability in determination of the optimum rate of N fertilizer application using a crop model: A case study for rainfed corn in eastern Canada

Science.gov (United States)

Mesbah, M.; Pattey, E.; Jégo, G.; Geng, X.; Tremblay, N.; Didier, A.

2017-12-01

Identifying optimum nitrogen (N) application rate is essential for increasing agricultural production while limiting potential environmental contaminations caused by release of reactive N, especially for high demand N crops such as corn. The central question of N management is then how the optimum N rate is affected by climate variability for given soil. The experimental determination of optimum N rates involve the analyses of variance on the mean value of crop yield response to various N application rates used by factorial plot based experiments for a few years in several regions. This traditional approach has limitations to capture 1) the non-linear response of yield to N application rates due to large incremental N rates (often more than 40 kg N ha-1) and 2) the ecophysiological response of the crop to climate variability because of limited numbers of growing seasons considered. Modeling on the other hand, does not have such limitations and hence we use a crop model and propose a model-based methodology called Finding NEMO (N Ecophysiologically Modelled Optimum) to identify the optimum N rates for variable agro-climatic conditions and given soil properties. The performance of the methodology is illustrated using the STICS crop model adapted for rainfed corn in the Mixedwood Plains ecozone of eastern Canada (42.3oN 83oW-46.8oN 71oW) where more than 90% of Canadian corn is produced. The simulations were performed using small increment of preplant N application rate (10 kg N ha -1), long time series of daily climatic data (48 to 61 years) for 5 regions along the ecozone, and three contrasting soils per region. The results show that N recommendations should be region and soil specific. Soils with lower available water capacity required more N compared to soil with higher available water capacity. When N rates were at their ecophysiologically optimum level, 10 to 17 kg increase in dry yield could be achieved by adding 1 kg N. Expected yield also affected the optimum

Determination of the effective radiative lifetimes of the 6 3P1 atomic mercury level in low-pressure mercury discharges

International Nuclear Information System (INIS)

van de Weijer, P.; Cremers, R.M.M.

1984-01-01

Experiments are described in which low-pressure mercury, mercury-argon and mercury-krypton discharges were irradiated with a dye laser pulse at 365.5 nm, thus exciting mercury atoms from the metastable 6 3 P 2 level to the 6 3 D 2 level. The 6 3 D 2 level decays radiatively to the 6 P levels. By recording the time dependence of the overpopulation in the 6 3 P 1 and the 6 1 P 1 level at the fluorescence signals at 254 nm and 185 nm, respectively, the effective radiative lifetime of these levels were determined. The effective radiative lifetime of the 6 3 P 1 level was measured in the k 0 R regime 0.1-500. The 6 1 P 1 lifetime was determined for the following discharge conditions: tube diameter 10-36 mm, mercury density 7.10 18 -2.10 21 m -3 , and noble gas pressure 0, 130, 400 Pa

Interaction between intra-abdominal pressure and positive-end expiratory pressure

Directory of Open Access Journals (Sweden)

Jamili Anbar Torquato

2009-02-01

Full Text Available OBJECTIVE: The aim of this study was to quantify the interaction between increased intra-abdominal pressure and Positive-End Expiratory Pressure. METHODS: In 30 mechanically ventilated ICU patients with a fixed tidal volume, respiratory system plateau and abdominal pressure were measured at a Positive-End Expiratory Pressure level of zero and 10 cm H2O. The measurements were repeated after placing a 5 kg weight on the patients' belly. RESULTS: After the addition of 5 kg to the patients' belly at zero Positive-End Expiratory Pressure, both intra-abdominal pressure (p<0.001 and plateau pressures (p=0.005 increased significantly. Increasing the Positive-End Expiratory Pressure levels from zero to 10 cm H2O without weight on the belly did not result in any increase in intra-abdominal pressure (p=0.165. However, plateau pressures increased significantly (p< 0.001. Increasing Positive-End Expiratory Pressure from zero to 10 cm H2O and adding 5 kg to the belly increased intra-abdominal pressure from 8.7 to 16.8 (p<0.001 and plateau pressure from 18.26 to 27.2 (p<0.001. Maintaining Positive-End Expiratory Pressure at 10 cm H2O and placing 5 kg on the belly increased intra-abdominal pressure from 12.3 +/- 1.7 to 16.8 +/- 1.7 (p<0.001 but did not increase plateau pressure (26.6+/-1.2 to 27.2 +/-1.1 -p=0.83. CONCLUSIONS: The addition of a 5kg weight onto the abdomen significantly increased both IAP and the airway plateau pressure, confirming that intra-abdominal hypertension elevates the plateau pressure. However, plateau pressure alone cannot be considered a good indicator for the detection of elevated intra-abdominal pressure in patients under mechanical ventilation using PEEP. In these patients, the intra-abdominal pressure must also be measured.

Development of an improved-contact liquid-level probe for pressurized reactor vessels

International Nuclear Information System (INIS)

Kelsey, P.V. Jr.

1982-09-01

Electrical-conductivity-based probes for liquid level sensing show promise for pressurized water reactor environments, but have exhibited frequent bond failures at the ceramic/metal interfaces. A program to characterize and improve the interface behavior has been completed successfully, and has provided data for optimizing fabrication parameters, as well as general information on glass-to-metal bonding in a superalloy/silicate-glass system. The materials studied were Inconel X-750 and a barium silicate glass containing minor amounts of TiO 2 , CeO 2 , As 2 O 3 , Bi 2 O 3 , and Al 2 O 3

Optimum principle for a vehicular traffic network: minimum probability of congestion

Energy Technology Data Exchange (ETDEWEB)

Kerner, Boris S, E-mail: boris.kerner@daimler.com [Daimler AG, GR/PTF, HPC: G021, 71059 Sindelfingen (Germany)

2011-03-04

We introduce an optimum principle for a vehicular traffic network with road bottlenecks. This network breakdown minimization (BM) principle states that the network optimum is reached when link flow rates are assigned in the network in such a way that the probability for spontaneous occurrence of traffic breakdown in at least one of the network bottlenecks during a given observation time reaches the minimum possible value. Based on numerical simulations with a stochastic three-phase traffic flow model, we show that in comparison to the well-known Wardrop's principles, the application of the BM principle permits considerably greater network inflow rates at which no traffic breakdown occurs and, therefore, free flow remains in the whole network. (fast track communication)

Ventilation distribution measured with EIT at varying levels of pressure support and Neurally Adjusted Ventilatory Assist in patients with ALI.

Science.gov (United States)

Blankman, Paul; Hasan, Djo; van Mourik, Martijn S; Gommers, Diederik

2013-06-01

The purpose of this study was to compare the effect of varying levels of assist during pressure support (PSV) and Neurally Adjusted Ventilatory Assist (NAVA) on the aeration of the dependent and non-dependent lung regions by means of Electrical Impedance Tomography (EIT). We studied ten mechanically ventilated patients with Acute Lung Injury (ALI). Positive-End Expiratory Pressure (PEEP) and PSV levels were both 10 cm H₂O during the initial PSV step. Thereafter, we changed the inspiratory pressure to 15 and 5 cm H₂O during PSV. The electrical activity of the diaphragm (EAdi) during pressure support ten was used to define the initial NAVA gain (100 %). Thereafter, we changed NAVA gain to 150 and 50 %, respectively. After each step the assist level was switched back to PSV 10 cm H₂O or NAVA 100 % to get a new baseline. The EIT registration was performed continuously. Tidal impedance variation significantly decreased during descending PSV levels within patients, whereas not during NAVA. The dorsal-to-ventral impedance distribution, expressed according to the center of gravity index, was lower during PSV compared to NAVA. Ventilation contribution of the dependent lung region was equally in balance with the non-dependent lung region during PSV 5 cm H₂O, NAVA 50 and 100 %. Neurally Adjusted Ventilatory Assist ventilation had a beneficial effect on the ventilation of the dependent lung region and showed less over-assistance compared to PSV in patients with ALI.

Pneumatic pressure wave generator provides economical, simple testing of pressure transducers

Science.gov (United States)

Gaal, A. E.; Weldon, T. P.

1967-01-01

Testing device utilizes the change in pressure about a bias or reference pressure level produced by displacement of a center-driven piston in a closed cylinder. Closely controlled pneumatic pressure waves allow testing under dynamic conditions.

Relationship between Food Security with Sugar Level and Blood Pressure in Diabetes Type 2 in Tehran.

Science.gov (United States)

Moghadam, Seyed Amir Hossein Zehni; Javadi, Maryam; Mohammadpooral, Asghar

2016-12-01

Food security has been defined as the "availability, stability, access and utilization of safe foods". Diabetes has been known as one of the biggest health and medical problems throughout the world and is clearly related to lifestyle, and particularly, improper food consumption. The aim of this study was to determine the relationship between food security with sugar and blood pressure in patients suffering from type 2 diabetes who refer to diabetes centers in Tehran. This cross-sectional study was conducted in 2015 on type 2 diabetes patients in Tehran, Iran. From two diabetes centers in the eastern and southern parts of Tehran, 243 type 2 diabetes patients were selected. Necessary information (demographic and food security information) about all the studied persons was collected using the standard questionnaire verified by US Department of Agriculture (USDA). The data was analyzed by SPSS version 16, statistical comparisons were made using analysis of variance (ANOVA) and Chi-square and Tukey tests and a significant level of food security (p=0.372). No significant relation was observed between food security and fasting blood pressure, HbA1C, and systolic blood pressure (p>0.05), but there was a significant relationship between food security and diastolic blood pressure (p= 0.030). According to the relationship between diastolic blood pressure and food security and the role of blood pressure in the irreparable diabetic complications, it is recommended to perform appropriate food advice.

Optimum geometry for torque ripple minimization of switched reluctance motors

NARCIS (Netherlands)

Sahin, F.; Ertan, H.B.; Leblebicioglu, K.

2000-01-01

For switched reluctance motors, one of the major problems is torque ripple which causes increased undesirable acoustic noise and possibly speed ripple. This paper describes an approach to determine optimum magnetic circuit parameters to minimize low speed torque ripple for such motors. The

Optimum Peak Current Hysteresis Control for Energy Recovering Converter in CDI Desalination

Directory of Open Access Journals (Sweden)

Alberto M. Pernía

2014-06-01

Full Text Available Capacitive De-Ionization (CDI is becoming a suitable alternative for desalination. The low cost of the materials required and its reduced energy consumption can be critical factors for developing this technique. CDI technology does not require a high-pressure system and the energy storage capability of CDI cells allows it to be reused in other CDI cells, thus minimizing consumption. The goal of the power stage responsible of the energy recovery is transferring the stored energy from one cell to another with the maximum possible efficiency, thus allowing the desalination process to continue. Assuming hysteresis current control is implemented at the DC/DC (direct current converter, this paper aims to determine the optimum peak current through the inductor in each switching period with a view to maximizing overall efficiency. The geometrical parameters of the desalination cell and the NaCl concentration modify the cell electrical properties. The peak current control of the power stage should be adapted to the cell characteristics so that the efficiency behavior of the whole CDI system can be improved. The mathematical model defined in this paper allows the CDI plant automation using the peak inductor current as control variable, adapting its value to the salt concentration during the desalination process.

Determination of the Optimum Ozone Product on the Plasma Ozonizer

International Nuclear Information System (INIS)

Agus Purwadi; Widdi Usada; Suryadi; Isyuniarto; Sri Sukmajaya

2002-01-01

An experiment of the optimum ozone product determination on the cylindrical plasma ozonizer has been done. The experiment is carried out by using alternating high voltage power supply, oscilloscope CS-1577 A, flow meter and spectronik-20 instrument for the absorbance solution samples which produced by varying the physics parameter values of the discharge alternating high voltage and velocity of oxygen gas input. The plasma ozonizer is made of cylinder stainless steel as the electrode and cylinder glass as the dielectric with 1.00 mm of the discharge gap and 7.225 mm 3 of the discharge tube volume. The experiment results shows that the optimum ozone product is 0.360 mg/s obtained at the the discharge of alternating high voltage of 25.50 kV, the frequency of 1.00 kHz and the rate of oxygen gas input of 1.00 lpm. (author)

Determination of optimum oven cooking procedures for lean beef products.

Science.gov (United States)

Rodas-González, Argenis; Larsen, Ivy L; Uttaro, Bethany; Juárez, Manuel; Parslow, Joyce; Aalhus, Jennifer L

2015-11-01

In order to determine optimum oven cooking procedures for lean beef, the effects of searing at 232 or 260°C for 0, 10, 20 or 30 min, and roasting at 160 or 135°C on semimembranosus (SM) and longissimus lumborum (LL) muscles were evaluated. In addition, the optimum determined cooking method (oven-seared for 10 min at 232°C and roasted at 135°C) was applied to SM roasts varying in weight from 0.5 to 2.5 kg. Mainly, SM muscles seared for 0 or 10 min at 232°C followed by roast at 135°C had lower cooking loss, higher external browning color, more uniform internal color, and were more tender and flavorful (P searing is the recommended oven cooking procedure; with best response from muscle roast weight ≥1 kg.

Determination of Optimum Moisture Content of Palm Nut Cracking ...

African Journals Online (AJOL)

USER

ABSTRACT: After processing the palm fruit for oil, the nut is usually dried in order to loosen the kernel from the shell. The drying is necessary to enhance the release of whole kernel when the nut is cracked. A study was carried out to determine the optimum moisture content of nuts for high yield of whole kernels during ...

The Model of Optimum Economic Growth with the Induced Scientific-Technological Progress

Directory of Open Access Journals (Sweden)

Dilenko Viktor A.

2017-07-01

Full Text Available On the basis of the economic dynamics of the Harrod – Domar model, a model of optimum economic growth in line with the induced scientific-technological progress (STP has been built. In order to reflect the induced scientific-technological progress, with this model is proposed to further allocate the income element that is specially used for the investment of innovation activity, implementation of which reduces the capital intensity in development of the discussed economy. For the simplest way of presenting an economic mechanism for the investment of induced STP, analytical solutions of an appropriate task in optimum management have been obtained. Studying these decisions allowed to reveal the characteristics of the impact of parameters of scientific-technological progress and the analyzed economic system on choosing the best trajectory for its evolution. Possible directions for further developing the results presented can be considered the tasks in building and analyzing models of optimum economic growth that implement different investment options for the induced STP, as well as the models in which this investment mechanism is not exogenouslyed, but rather the result of the corresponding economic-mathematical research.

Estimation of Optimum Dilution in the GMAW Process Using Integrated ANN-GA

Directory of Open Access Journals (Sweden)

P. Sreeraj

2013-01-01

Full Text Available To improve the corrosion resistant properties of carbon steel, usually cladding process is used. It is a process of depositing a thick layer of corrosion resistant material over carbon steel plate. Most of the engineering applications require high strength and corrosion resistant materials for long-term reliability and performance. By cladding these properties can be achieved with minimum cost. The main problem faced on cladding is the selection of optimum combinations of process parameters for achieving quality clad and hence good clad bead geometry. This paper highlights an experimental study to optimize various input process parameters (welding current, welding speed, gun angle, and contact tip to work distance and pinch to get optimum dilution in stainless steel cladding of low carbon structural steel plates using gas metal arc welding (GMAW. Experiments were conducted based on central composite rotatable design with full replication technique, and mathematical models were developed using multiple regression method. The developed models have been checked for adequacy and significance. In this study, artificial neural network (ANN and genetic algorithm (GA techniques were integrated and labeled as integrated ANN-GA to estimate optimal process parameters in GMAW to get optimum dilution.

Optimum MRS site location to minimize spent fuel transportation impacts

International Nuclear Information System (INIS)

Hoskins, R.E.

1987-01-01

A range of spent fuel transportation system parameters are examined in terms of attributes important to minimizing transportation impacts as a basis for identifying geographic regions best suited for siting a monitored retrievable storage (MRS) facility. Transportation system parameters within existing transport cask design and transportation mode capabilities were systematically analyzed. The optimum MRS location was found to be very sensitive to transportation system assumptions particularly with regard to the relative efficiencies of the reactor-to-MRS and MRS-to-repository components of the system. Moreover, dramatic improvements in the reactor-to-MRS component can be made through use of multiple cask shipment of the largest practical casks by dedicated train compared to the traditional single cask rail (70%) and truck (30%) shipments assumed the Department of Energy in their studies that defined the optimum MRS location in the vicinity of Tennessee. It is important to develop and utilize an efficient transportation system irrespective of whether or not an MRS is in the system. Assuming reasonably achievable efficiency in reactor-to-MRS spent fuel transportation and assigning equal probabilities to the three western sites selected for characterization of being the repository site, the optimum MRS location would be in the far-mid-western states. Based on various geographic criteria including barge access and location in a nuclear service area, the State of Tennessee ranks any place from 12th to the 25th at a penalty of about 30% over the minimum achievable impacts. While minimizing transportation impacts is an important factor, other criteria should also be considered in selecting an MRS site

Intraoperative and postoperative evaluation of low tidal volume combined with low-level positive end-expiratory pressure ventilation in laparoscopic surgery in elderly patients

Directory of Open Access Journals (Sweden)

Ye-Qiu Li

2016-01-01

Full Text Available Objective: To evaluate intraoperative and postoperative condition of low tidal volume combined with low-level positive end-expiratory pressure ventilation in laparoscopic surgery in elderly patients. Methods: A total of 176 cases of elderly patients (more than 60 years old receiving laparoscopic surgery in our hospital from July 2013 to July 2015 were selected as research subjects and randomly divided into observation group and control group, each group included 88 cases, control group received conventional ventilation strategy, observation group received low tidal volume combined with low-level positive end-expiratory pressure ventilation strategy, and then levels of hemodynamic indexes, respiratory mechanical indexes, serology indexes and cerebral vessel related indexes, etc of two groups were compared. Results: Intraoperative and postoperative heart rate and mean arterial pressure levels of observation group were lower than those of control group, arterial partial pressure of oxygen and oxygenation index levels were higher than those of control group and differences had statistical significance (P<0.05; intraoperative APIP and Pplat values of observation group were lower than those of control group, Cs value was higher than that of control group and differences had statistical significance (P<0.05; intraoperative and postoperative serum IL-8 and TNF-α levels of observation group were lower than those of control group, IL-10 level was higher than that of control group and differences had statistical significance (P<0.05; intraoperative and postoperative PjvO2, SjvO2 and CjvO2 levels of observation group were higher than those of control group, Da-jvO2 level was lower than that of control group and differences had statistical significance (P<0.05. Conclusions: When elderly patients receive laparoscopic surgery, the use of low tidal volume combined with low-level positive end-expiratory pressure ventilation strategy can stabilize hemodynamic

Effects of different feeding levels on moulting, growth, food conversion efficiency and biochemical composition of the prawn, metapenaeus monoceros (Fabricius)

Digital Repository Service at National Institute of Oceanography (India)

Sumitra-Vijayaraghavan; Royan, J.P.; Rao, T.S.S.

food/g prawn/day represented the maintenance, optimum and maximum feeding levels Specific dynamic action increased twice at the observed maximum feeding level (20%) than at optimum feeding level (12%), indicating that the energy cost of converting food...

METHODS FOR DETERMINATION OF THE OPTIMUM EXPLOSIVES IN DIFFERENT ROCKS

Directory of Open Access Journals (Sweden)

Josip Krsnik

1989-12-01

Full Text Available The most appropriate explosives required for blasting of the particular types of rocks were established by test blasting method with linear burden increase. By the same method the optimum magnitudes of deep-holes blasting were established (the paper is published in Croatian.

Feasibility study of a pressure-fed engine for a water recoverable space shuttle booster. Volume 1: Executive summary

Science.gov (United States)

1972-01-01

An overview is presented of the results of the analyses conducted in support of the selected engine system for the pressure-fed booster stage. During initial phases of the project, a gimbaled, regeneratively cooled, fixed thrust engine having a coaxial pintle injector was selected as optimum for this configuration.

Completely integrated prestressed-concrete reactor pressure vessel, type 'Star'

International Nuclear Information System (INIS)

Neunert, B.; Jueptner, G.; Kumpf, H.

1975-01-01

The star support vessel is suitable for the connection to all primary circuit systems consisting of a main vessel and a number of satellite vessels around and connected to it, i.e. for LWR, HTR and process reactor. It must be made clear, however, that the PWR in particular with its components does not appear to be suited for the optimum incorporation in a prestressed-concrete pressure vessel system, no matter what kind. There are clear concepts about modifications which, however, require considerable development expenditure. (orig./LH) [de

On the system optimum of traffic assignment in M/G/c/c state-dependent queueing networks

NARCIS (Netherlands)

Cruz, F.R.B.; Woensel, van T.; MacGregor Smith, J.; Lieckens, K.

2010-01-01

The classical Wardrop System Optimum assignment model assumes that the users will cooperate with each other in order to minimize the overall travel costs. The importance of the system optimum model lies on its well-recognized ability of producing solutions that correspond to the most efficient way

Compaction Filter as an Optimum Solution for Multirate Subband Coder of Cyclostationary Signals

Directory of Open Access Journals (Sweden)

D. Kula

2003-09-01

Full Text Available A consistent theory of optimum subband coding of zero meanwide-sense cyclostationary signals with N-periodic statistics ispresented in this paper. Blocked polyphase representation of theanalysis and synthesis filter banks is introduced as an effective wayof multirate subband coder description. Optimum energy compaction usingNyquist-M process is presented as a solution for maximizing the codinggain of the coder. In two definitions and four theorems the authorproves that Nyquist-M filters fulfill necessary and sufficientconditions imposed on subband signals. Results from Matlab simulationsare presented to support theoretical conclusions.

Research on decommissioning of nuclear facilities 2. Study on optimum scenario using the AHP (Joint research)

International Nuclear Information System (INIS)

Shibahara, Yuji; Morishita, Yoshitsugu; Ishigami, Tsutomu; Yanagihara, Satoshi; Arita, Yuji

2013-01-01

To implement a decommissioning project reasonably, it is necessary and important to calculate project management data beforehand as well as to select an optimum dismantling scenario among various scenarios postulated. Little study on the subject of selecting an optimum scenario has been carried out, and it is one of the most important issues in terms of decision making. In FY 2009, Japan Atomic Energy Agency and University of Fukui launched the joint research of a decision making method which is important to determine a decommissioning plan. The purpose of this research is to formulate a methodology for selecting an optimum dismantling scenario among various scenarios postulated based on calculated results of project management data for FUGEN. Project management data for several dismantling scenarios postulated at FUGEN were evaluated based on actual dismantling work for feedwater heater at FUGEN, and an optimum scenario was discussed using the AHP, one of Multi-Criteria Decision Analysis Methods. This report describes the results of the joint research in FY 2010. (author)

Calpain-5 gene variants are associated with diastolic blood pressure and cholesterol levels

Directory of Open Access Journals (Sweden)

Morón Francisco J

2007-01-01

Full Text Available Abstract Background Genes implicated in common complex disorders such as obesity, type 2 diabetes mellitus (T2DM or cardiovascular diseases are not disease specific, since clinically related disorders also share genetic components. Cysteine protease Calpain 10 (CAPN10 has been associated with T2DM, hypertension, hypercholesterolemia, increased body mass index (BMI and polycystic ovary syndrome (PCOS, a reproductive disorder of women in which isunlin resistance seems to play a pathogenic role. The calpain 5 gene (CAPN5 encodes a protein homologue of CAPN10. CAPN5 has been previously associated with PCOS by our group. In this new study, we have analysed the association of four CAPN5 gene variants(rs948976A>G, rs4945140G>A, rs2233546C>T and rs2233549G>A with several cardiovascular risk factors related to metabolic syndrome in general population. Methods Anthropometric measurements, blood pressure, insulin, glucose and lipid profiles were determined in 606 individuals randomly chosen from a cross-sectional population-based epidemiological survey in the province of Segovia in Central Spain (Castille, recruited to investigate the prevalence of anthropometric and physiological parameters related to obesity and other components of the metabolic syndrome. Genotypes at the four polymorphic loci in CAPN5 gene were detected by polymerase chain reaction (PCR. Results Genotype association analysis was significant for BMI (p ≤ 0.041, diastolic blood pressure (p = 0.015 and HDL-cholesterol levels (p = 0.025. Different CAPN5 haplotypes were also associated with diastolic blood pressure (DBP (0.0005 ≤ p ≤ 0.006 and total cholesterol levels (0.001 ≤ p ≤ 0.029. In addition, the AACA haplotype, over-represented in obese individuals, is also more frequent in individuals with metabolic syndrome defined by ATPIII criteria (p = 0.029. Conclusion As its homologue CAPN10, CAPN5 seems to influence traits related to increased risk for cardiovascular diseases. Our

Water level indicator

International Nuclear Information System (INIS)

Murase, Michio; Araki, Hidefumi.

1996-01-01

A difference of pressure between a standard pressure conduit in communication with a gas phase of a reactor pressure vessel and a water level pressure conduit in communication with a liquid phase of the pressure vessel is detected by a pressure difference gage. A communication pipe and a standard level vessel are disposed between the pressure vessel and the standard pressure conduit, and a standard liquid surface on the side of the standard pressure conduit is formed in the standard level vessel. A gas releaser is disposed to the gas phase portion of the standard level vessel. The gas releaser equipment is constituted by a porous material, a permeation membrane and a gas exhaustion hole. The gas phase of the standard level vessel is divided by a partition plate into a first gas phase being in contact with a connection portion with the communication pipe and a second gas phase in contact with the gas releaser. A gas flow channel hole and a condensate descending hole are disposed to the partition plate. Since incondensible gases accumulated to the standard level vessel are effectively exhausted, the incondensible gases are prevented from being dissolved into liquid. (I.N.)

From user equilibrium to system optimum : a literature review on the role of travel information, bounded rationality and non-selfish behaviour at the network and individual levels

NARCIS (Netherlands)

van Essen, Mariska; Thomas, Tom; van Berkum, Eric; Chorus, C.G.

2016-01-01

Travel information continues to receive significant attention in the field of travel behaviour research, as it is expected to help reduce congestion by directing the network state from a user equilibrium towards a more efficient system optimum. This literature review contributes to the existing

From user equilibrium to system optimum: a literature review on the role of travel information, bounded rationality and non-selfish behaviour at the network and individual levels

NARCIS (Netherlands)

van Essen, Mariska Alice; Thomas, Tom; van Berkum, Eric C.; Chorus, C.

2016-01-01

Travel information continues to receive significant attention in the field of travel behaviour research, as it is expected to help reduce congestion by directing the network state from a user equilibrium towards a more efficient system optimum. This literature review contributes to the existing

Toward power scaling in an acetylene mid-infrared hollow-core optical fiber gas laser: effects of pressure, fiber length, and pump power

Science.gov (United States)

Weerasinghe, H. W. Kushan; Dadashzadeh, Neda; Thirugnanasambandam, Manasadevi P.; Debord, Benoît.; Chafer, Matthieu; Gérôme, Frédéric; Benabid, Fetah; Corwin, Kristan L.; Washburn, Brian R.

2018-02-01

The effect of gas pressure, fiber length, and optical pump power on an acetylene mid-infrared hollow-core optical fiber gas laser (HOFGLAS) is experimentally determined in order to scale the laser to higher powers. The absorbed optical power and threshold power are measured for different pressures providing an optimum pressure for a given fiber length. We observe a linear dependence of both absorbed pump energy and lasing threshold for the acetylene HOFGLAS, while maintaining a good mode quality with an M-squared of 1.15. The threshold and mode behavior are encouraging for scaling to higher pressures and pump powers.

The Optimum Conditions of Foreign Languages in Primary Education

Science.gov (United States)

Giannikas, Christina Nicole

2014-01-01

The aim of the paper is to review the primary language learning situation in Europe and shed light on the benefits it carries. Early language learning is the biggest policy development in education and has developed in rapid speed over the past 30 years; this article considers the effects and advantages of the optimum condition of an early start,…

Optimum design of Nd-doped fiber optical amplifiers

DEFF Research Database (Denmark)

Rasmussen, Thomas; Bjarklev, Anders Overgaard; Lumholt, Ole

1992-01-01

The waveguide parameters for a Nd-doped fluoride (Nd:ZBLANP) fiber amplifier have been optimized for small-signal and booster operation using an accurate numerical model. The optimum cutoff wavelength is shown to be 800 nm and the numerical aperture should be made as large as possible. Around 80%......% booster quantum conversion efficiency can be reached for an input power of 10 dBm and a pump power of 100 mW by the use of one filter...

Sequence homolog-based molecular engineering for shifting the enzymatic pH optimum

Directory of Open Access Journals (Sweden)

Fuqiang Ma

2016-09-01

Full Text Available Cell-free synthetic biology system organizes multiple enzymes (parts from different sources to implement unnatural catalytic functions. Highly adaption between the catalytic parts is crucial for building up efficient artificial biosynthetic systems. Protein engineering is a powerful technology to tailor various enzymatic properties including catalytic efficiency, substrate specificity, temperature adaptation and even achieve new catalytic functions. However, altering enzymatic pH optimum still remains a challenging task. In this study, we proposed a novel sequence homolog-based protein engineering strategy for shifting the enzymatic pH optimum based on statistical analyses of sequence-function relationship data of enzyme family. By two statistical procedures, artificial neural networks (ANNs and least absolute shrinkage and selection operator (Lasso, five amino acids in GH11 xylanase family were identified to be related to the evolution of enzymatic pH optimum. Site-directed mutagenesis of a thermophilic xylanase from Caldicellulosiruptor bescii revealed that four out of five mutations could alter the enzymatic pH optima toward acidic condition without compromising the catalytic activity and thermostability. Combination of the positive mutants resulted in the best mutant M31 that decreased its pH optimum for 1.5 units and showed increased catalytic activity at pH < 5.0 compared to the wild-type enzyme. Structure analysis revealed that all the mutations are distant from the active center, which may be difficult to be identified by conventional rational design strategy. Interestingly, the four mutation sites are clustered at a certain region of the enzyme, suggesting a potential “hot zone” for regulating the pH optima of xylanases. This study provides an efficient method of modulating enzymatic pH optima based on statistical sequence analyses, which can facilitate the design and optimization of suitable catalytic parts for the construction

What is the effect of optimum independent parameters on solar heating systems?

International Nuclear Information System (INIS)

Kaçan, Erkan; Ulgen, Koray; Kaçan, Erdal

2015-01-01

Highlights: • The efficiency effect of 4 independent parameters over the solar heating system are examined. • 3 of 4 independent parameters are found as decisive parameter for system design. • Maximum exergetic efficiency exceeded 11% at optimized process. • Maximum environmental efficiency reached up to 95% at optimized process. • The optimum outside temperature and solar radiation are found as 22 °C and 773 W/m"2 for all responses. - Abstract: Researchers are rather closely involved in Solar Combisystems recently, but there is lack of study that presents the optimum design parameters. Therefore, in this study the influence of the four major variables, namely; outside, inside temperature, solar radiation on horizontal surface and instantaneous efficiency of solar collector on the energetic, exergetic and environmental efficiencies of Solar Combisystems are investigated and system optimization is done by a combination of response surface methodology. Measured parameters and energetic–exergetic and environmental performance curves are found and statistical model is created parallel with the actual data. It is found that statistical model is significant and all “lack-of-fit” values are non-significant. Thus, it is proved that statistical model strongly represents the design model. Outside temperature, solar radiation on horizontal surface and instantaneous efficiency of solar collector are the decisive parameters for all responses but instantaneous efficiency of solar collector is not for environmental efficiency. Maximum exergetic efficiency exceeded 11%, maximum environmental efficiency reached up to 95% at optimized process. The optimum value of the outside temperature and solar radiation are found as 22 °C and 773 W/m"2 for all responses, on the other hand optimum collector efficiency is found around 60% for energetic and exergetic efficiency values. Inside temperature is not a decisive parameter for all responses.

A Study on the Optimum Bucket Size for Master Scheduling : For the Case of Hierarchically tured Products

OpenAIRE

木内, 正光

2010-01-01

The function of master scheduling is to plan the flow of order from its arrival to its completion. In this study, the problem of bucket size for master scheduling is taken up. The bucket size for master scheduling has much influence on the lead time of the order. However, to date there is no clear method for how to set the optimum bucket size. The purpose of this study is to propose a method to set the optimum bucket size. In this paper, an equation to estimate the optimum bucket size is prop...