Mercury speciation and fine particle size distribution on combustion of Chinese coals

Energy Technology Data Exchange (ETDEWEB)

Zhang, Lei; Wang, Shuxiao; Hao, Jiming [Tsinghua Univ., Beijing (China). Dept. of Environmental Science and Engineering and State Key Joint Lab. of Environment Simulation and Pollution Control; Daukoru, Michael; Torkamani, Sarah; Biswas, Pratim [Washington Univ., St. Louis, MO (United States). Aerosol and Air Quality Research Lab.

2013-07-01

Coal combustion is the dominant anthropogenic mercury emission source of the world. Electrostatic precipitator (ESP) can remove almost all the particulate mercury (Hg{sub p}), and wet flue gas desulfurization (WFGD) can retain a large part of the gaseous oxidized mercury (Hg{sup 2+}). Only a small percentage of gaseous elemental mercury (Hg{sup 0}) can be abated by the air pollution control devices (APCDs). Therefore, the mercury behavior across APCDs largely depends on the mercury speciation in the flue gas exhausting from the coal combustor. To better understand the formation process of three mercury species, i.e. Hg{sup 0}, Hg{sup 2+} and Hg{sub p}, in gaseous phase and fine particles, bench-scale measurements for the flue gas exhausting from combustion of different types of coal in a drop-tube furnace set-up, were carried out. It was observed that with the limitation of reaction kinetics, higher mercury concentration in flue gas will lead to lower Hg{sup 2+} proportion. The concentration of chlorine has the opposite effect, not as significantly as that of mercury though. With the chlorine concentration increasing, the proportion of Hg{sup 2+} increases. Combusting the finer coal powder results in the formation of more Hg{sup 2+}. Mineral composition of coal and coal particle size has a great impact on fine particle formation. Al in coal is in favor of finer particle formation, while Fe in coal can benefit the formation of larger particles. The coexistence of Al and Si can strengthen the particle coagulation process. This process can also be improved by the feeding of more or finer coal powder. The oxy-coal condition can make for both the mercury oxidation process and the metal oxidation in the fine particle formation process.

Coal surface control for advanced physical fine coal cleaning technologies. Final report, September 19, 1988--August 31, 1992

Energy Technology Data Exchange (ETDEWEB)

Morsi, B.I.; Chiang, S.H.; Sharkey, A.; Blachere, J.; Klinzing, G.; Araujo, G.; Cheng, Y.S.; Gray, R.; Streeter, R.; Bi, H.; Campbell, P.; Chiarlli, P.; Ciocco, M.; Hittle, L.; Kim, S.; Kim, Y.; Perez, L.; Venkatadri, R.

1992-12-31

This final report presents the research work carried out on the Coal Surface Control for Advanced Physical Fine Coal Cleaning Technologies project, sponsored by the US Department of Energy, Pittsburgh Energy Technology Center (DOE/PETC). The project was to support the engineering development of the selective agglomeration technology in order to reduce the sulfur content of US coals for controlling SO{sub 2} emissions (i.e., acid rain precursors). The overall effort was a part of the DOE/PETCs Acid Rain Control Initiative (ARCI). The overall objective of the project is to develop techniques for coal surface control prior to the advanced physical fine coal cleaning process of selective agglomeration in order to achieve 85% pyrite sulfur rejection at an energy recovery greater than 85% based on run-of-mine coal. The surface control is meant to encompass surface modification during grinding and laboratory beneficiation testing. The project includes the following tasks: Project planning; methods for analysis of samples; development of standard beneficiation test; grinding studies; modification of particle surface; and exploratory R&D and support. The coal samples used in this project include three base coals, Upper Freeport - Indiana County, PA, Pittsburgh NO. 8 - Belmont County, OH, and Illinois No. 6 - Randolph County, IL, and three additional coals, Upper Freeport - Grant County- WV, Kentucky No. 9 Hopkins County, KY, and Wyodak - Campbell County, WY. A total of 149 drums of coal were received.

Fine coke production from brown coal (Report on ECSC contract 6220-72/1/102)

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

The possibility of producing a dry brown coal suitable for the production of fine coke and the development of a suitable carbonization process were studied. To prepare the coal it should be screened at 1 mm with the oversize going to fine coke production and the undersize going to briquette production. To increase fine coke production it is necessary to screen the raw smalls less than 2 mm and to pelletize, dry and carbonize them with the coarser constituents. The planning and construction of a hearth oven furnace plant was begun and this is now in operation. A fluidized bed can be used to preheat the coal to improve the oven performance. (In German)

Comparative study of the performance of conventional and column flotation when treating coking coal fines

Energy Technology Data Exchange (ETDEWEB)

Jena, M.S.; Biswal, S.K.; Das, S.P.; Reddy, P.S.R. [Institute of Minerals and Materials Technology (CSIR), Bhubaneswar - 751 013 (India)

2008-12-15

Investigations were carried out on coking coal fines by conventional cell and column flotation techniques. The effects of different operating parameters were evaluated for both conventional and column flotation. The coal fines were collected from Bhojudih washery, India. These coal fines averaged 24.4% ash, 19.8% volatile matter and 53.8% fixed carbon on a dry basis. A commercial grade sodium silicate, light diesel oil and pine oil were used as depressant, collector and frother respectively. The flotation performance was compared with release analysis. The conventional flotation results indicated that a clean coal with 14.4% ash could be obtained at 78.0% yield with 88.4% combustible recovery. The ash of the clean coal could be further reduced to 10.1% at 72.0% yield with 85.6% combustible recovery by using column flotation. The column flotation results were close to those obtained by release analysis. (author)

Leeuwpan fine coal dense medium plant

CSIR Research Space (South Africa)

Lundt, M

2010-11-01

Full Text Available Beneficiation 2010, 4–6 May 2010. 671The Journal of The Southern African Institute of Mining and Metallurgy VOLUME 110 NOVEMBER 2010 L Leeuwpan fine coal dense medium plant mixed with magnetite in the launder and enters... with production. Plant equipment operational changes Cyclone spigot changes In an attempt to lower the cut-point density, the spigot on the L 672 NOVEMBER 2010 VOLUME 110 The Journal of The Southern African Institute of Mining and Metallurgy Figure 1...

Fundamental study for improvement of dewatering of fine coal/refuse. Final report, August 1981-December 1984

Energy Technology Data Exchange (ETDEWEB)

Chiang, S.H.; Klinzing, G.E.; Morsi, B.I.; Tierney, J.W.; Binkley, T.; Chi, S.M.; Huang, S.; Qamar, I.; Venkatadri, R.

1984-12-01

Fine coal in slurry form must be dewatered to minimize handling and transportation problems and be reduced to a desirable level for subsequent preparation of coal/water mixtures as a substitute utility fuel. The current practice is inadequate for the dewatering of fine coal, particularly for coal particles with sizes smaller than 400 mesh. Therefore, it is most desirable to develop improved mechanical methods for reducing the moisture content of fine coal. In the light of this, a fundamental study of the dewatering of fine coal/refuse was initiated in June 1979 and continued through 1984. The overall objective of the study is to seek improved methods of dewatering through a better understanding of the filtration and post-filtration processes. As a first step, efforts have been focused on the mechanism of dewatering in terms of the basic properties of coal (and refuse) particles and the microstructures of filter cakes, and their relations to filtration rate and final moisture content. Pittsburgh seam-Bruceton Mine coal was used as a base coal. During the past year, filter cakes from coals with widely varying size ranges were micrographically characterized. The effects of a number of surface active agents and of entrapped air bubbles on the filter cake properties were also studied. Modules of the network model for calculating single phase and two phase permeabilities were formulated and tested. The report is divided into four parts: summary and deliverables; work forecast for 1984-1985; detailed description of technical progress; and appendices. 21 refs., 55 figs., 17 tabs.

Effect of a Dispersant Agent in Fine Coal Recovery from Washery Tailings by Oil Agglomeration (Preliminary Study)

Science.gov (United States)

Yasar, Özüm; Uslu, Tuncay

2017-12-01

Among the fine coal cleaning methods, the oil agglomeration process has important advantages such as high process recovery, more clean product, simple dewatering stage. Several coal agglomeration studies have been undertaken recently and effects of different variables on the process performance have been investigated. However, unlike flotation studies, most of the previous agglomeration studies have not used dispersing agents to minimize slime coating effects of clays. In this study, agglomeration process was applied for recovery of fine coals from coal washery tailings containing remarkable amount of fine coal. Negative effect of fine clays during recovery was tried to be eliminated by using dispersing agent instead of de-sliming. Although ash reductions over 90 % were achieved, performance remained below expectations in terms of combustible matter recovery. However, this study is a preliminary one. It is considered that more satisfied results will be obtained in the next studies by changing the variables such as solid ratio, oil dosage, dispersant type and dosage.

Bench-scale testing of a micronized magnetite, fine-coal cleaning process

Energy Technology Data Exchange (ETDEWEB)

Suardini, P.J. [Custom Coals, International, Pittsburgh, PA (United States)

1995-11-01

Custom Coals, International has installed and is presently testing a 500 lb/hr. micronized-magnetite, fine-coal cleaning circuit at PETC`s Process Research Facility (PRF). The cost-shared project was awarded as part of the Coal Preparation Program`s, High Efficiency Preparation Subprogram. The project includes design, construction, testing, and decommissioning of a fully-integrated, bench-scale circuit, complete with feed coal classification to remove the minus 30 micron slimes, dense medium cycloning of the 300 by 30 micron feed coal using a nominal minus 10 micron size magnetite medium, and medium recovery using drain and rinse screens and various stages and types of magnetic separators. This paper describes the project circuit and goals, including a description of the current project status and the sources of coal and magnetite which are being tested.

POC-scale testing of a dry triboelectrostatic separator for fine coal cleaning

Energy Technology Data Exchange (ETDEWEB)

Yoon, R.H.; Luttrell, G.H.; Adel, G.T. [Virginia Polytechnic Institute and State Univ., Blacksburg, VA (United States)

1995-11-01

Numerous advanced coal cleaning processes have been developed in recent years that are capable of substantially reducing both the ash and sulfur contents of run-of-mine coals. The extent of cleaning depends on the liberation characteristics of the coal, which generally improve with reducing particle size. however, since most of the advanced technologies are wet processes, the clean coal product must be dewatered before it can be transported and burned in conventional boilers. This additional treatment step significantly increases the processing cost and makes the industrial applicability of these advanced technologies much less attractive. In order to avoid problems associated with fine coal dewatering, researchers at the Pittsburgh Energy Technology Center (PETC) developed a novel triboelectrostatic separation (TES) process that can remove mineral matter from dry coal. In this technique, finely pulverized coal is brought into contact with a material (such as copper) having a work function intermediate to that of the carbonaceous material and associated mineral matter. Carbonaceous particles having a relatively low work function become positively charged, while particles of mineral matter having significantly higher work functions become negatively charged. once the particles become selectively charged, a separation can be achieved by passing the particle stream through an electrically charged field. Details related to the triboelectrostatic charging phenomenon have been discussed elsewhere (Inculet, 1984).

Optimizing the particle size of coal for CWM in view of fluidity. [Biomodal

Energy Technology Data Exchange (ETDEWEB)

Matsuo, Seiji; Nonaka, Michio; Okano, Yasuhiko; Inoue, Toshio

1987-10-25

As is well known, the viscosity of CWM is considerably influenced by the distribution of coal particle sizes and has bearing on particle packing density or porosity. A model for representing the viscosity of CWM in terms of particle porosity and specific surface was designed. Also, experimental verification was conducted for the method of optimizing particle size on a two-stage grinding system. The results are as follows: The viscosity of CWM is influenced not only by the porosity of coal particles, but also by the specific surface; also, it is correlated to the distance between suspended particles. At the two-stage grinding experiments, a particle size distribution leading to a low viscosity was obtained by mixing coarse and fine particles at 4:1. This has demonstrated that the use of an agitating mill for fine particles is of help. (11 figs, 2 tabs, 6 refs)

Amenability of some Witbank bituminous ultra fine coals to binderless briquetting

CSIR Research Space (South Africa)

Mangena, SJ

2004-10-15

Full Text Available and briquetting Each of the Witbank ultra fine coals was air-dried and subsequently split into five homogeneous portions of 5 kg, respectively. Four portions from each sample were physically wetted to ca. 5%, 10%, 15% and 20% H2O, automatically mixed for 15 min... and long-distance haulage in uncovered trucks during the rainy season. In terms of compressive strength, the SJM1 coal studied was amenable to conventional binderless briquetting. 3.1.2. SJM2 coal The effect of moisture on the compressive strength...

Briquetting of coal fines and sawdust. Part 1: binder and briquetting-parameters evaluations

Energy Technology Data Exchange (ETDEWEB)

D. Taulbee; D.P. Patil; Rick Q. Honaker; B.K. Parekh [University of Kentucky, Lexington, KY (United States). Center for Applied Energy Research

2009-01-15

Various technical and economic aspects relating to the briquetting of fine coal with sawdust have been evaluated with the results for two segments of that study presented here: binder and briquetting-parameter evaluations. Approximately 50 potential binder formulations were subjected to a series of screening evaluations to identify three formulations that were the most cost effective for briquetting fine coal with sawdust. Two of the binders, guar gum and wheat starch, were selected as most suitable for the pulverized coal market while the third formulation, lignosulfonate/lime, was targeted for the stoker market. Following binder selection, a number of briquetting parameters including binder and sawdust concentration, sawdust type, briquetting pressure and dwell time, coal and sawdust particle size, clay content, moisture content, and cure temperature and cure time were evaluated. Briquetting pressure and dwell time have the least impact while binder and sawdust concentrations, sawdust type, and curing conditions exerted the greatest influence on briquette quality. 7 refs.

Optimization of design and operating parameters in a pilot scale Jameson cell for slime coal cleaning

Energy Technology Data Exchange (ETDEWEB)

Hacifazlioglu, Hasan; Toroglu, Ihsan [Department of Mining Engineering, University of Karaelmas, 67100 (Turkey)

2007-07-15

The Jameson flotation cell has been commonly used to treat a variety of ores (lead, zinc, copper etc.), coal and industrial minerals at commercial scale since 1989. It is especially known to be highly efficient at fine and ultrafine coal recovery. However, although the Jameson cell has quite a simple structure, it may be largely inefficient if the design and operating parameters chosen are not appropriate. In this study, the design and operating parameters of a pilot scale Jameson cell were optimized to obtain a desired metallurgical performance in the slime coal flotation. The optimized design parameters are the nozzle type, the height of the nozzle above the pulp level, the downcomer diameter and the immersion depth of the downcomer. Among the operating parameters optimized are the collector dosage, the frother dosage, the percentage of solids and the froth height. In the optimum conditions, a clean coal with an ash content of 14.90% was obtained from the sample slime having 45.30% ash with a combustible recovery of 74.20%. In addition, a new type nozzle was developed for the Jameson cell, which led to an increase of about 9% in the combustible recovery value.

Engineering development of advanced physical fine coal cleaning for premium fuel applications

International Nuclear Information System (INIS)

1997-01-01

Bechtel, together with Amax Research and Development Center (Amax R ampersand D), has prepared this study which provides conceptual cost estimates for the production of premium quality coal-water slurry fuel (CWF) in a commercial plant. Two scenarios are presented, one using column flotation technology and the other the selective agglomeration to clean the coal to the required quality specifications. This study forms part of US Department of Energy program Engineering Development of Advanced Physical Fine Coal Cleaning for Premium Fuel Applications, (Contract No. DE-AC22- 92PC92208), under Task 11, Project Final Report. The primary objective of the Department of Energy program is to develop the design base for prototype commercial advanced fine coal cleaning facilities capable of producing ultra-clean coals suitable for conversion to stable and highly loaded CWF. The fuels should contain less than 2 lb ash/MBtu (860 grams ash/GJ) of HHV and preferably less than 1 lb ash/MBtu (430 grams ash/GJ). The advanced fine coal cleaning technologies to be employed are advanced column froth flotation and selective agglomeration. It is further stipulated that operating conditions during the advanced cleaning process should recover not less than 80 percent of the carbon content (heating value) in the run-of-mine source coal. These goals for ultra-clean coal quality are to be met under the constraint that annualized coal production costs does not exceed $2.5 /MBtu ($ 2.37/GJ), including the mine mouth cost of the raw coal. A further objective of the program is to determine the distribution of a selected suite of eleven toxic trace elements between product CWF and the refuse stream of the cleaning processes. Laboratory, bench-scale and Process Development Unit (PDU) tests to evaluate advanced column flotation and selective agglomeration were completed earlier under this program with selected coal samples. A PDU with a capacity of 2 st/h was designed by Bechtel and installed at

Research on desulfurisation of fine coal under compounding the physics force field

Energy Technology Data Exchange (ETDEWEB)

Tao, Y.; Fu, D.; Tao, D.; Liu, J.; Zhao, Y. [China University of Mining and Technology, Xuzhou (China)

2005-08-15

Desulphurization experiment carried on under compounding the physics force field was described for -0.5 mm fine particle of high sulphur coal. The experiment factorial plan of desulphurization on centrifugal gravity Falcon separator was designed and its results were analyzed by using Design-Expert 6.0 software. The 2-reactor interaction relation model between comprehensive desulphurization efficiency of pyrite sulphur and different operation variable was drawn, i.e. 2 FI model, and the 2-factor interaction on pyrite desulphurization efficiency of the operation factors differently was analyzed. The interaction on pyrite desulphurization efficiency of feed rate and feed concentration is significant. The optimization test condition for desulphurization was proposed by Design-Expert 6.0, and comprehensive desulphurization efficiency of 86.90% can be achieved. 5 refs., 3 figs., 7 tabs.

Low-rank coal research

Energy Technology Data Exchange (ETDEWEB)

Weber, G. F.; Laudal, D. L.

1989-01-01

This work is a compilation of reports on ongoing research at the University of North Dakota. Topics include: Control Technology and Coal Preparation Research (SO{sub x}/NO{sub x} control, waste management), Advanced Research and Technology Development (turbine combustion phenomena, combustion inorganic transformation, coal/char reactivity, liquefaction reactivity of low-rank coals, gasification ash and slag characterization, fine particulate emissions), Combustion Research (fluidized bed combustion, beneficiation of low-rank coals, combustion characterization of low-rank coal fuels, diesel utilization of low-rank coals), Liquefaction Research (low-rank coal direct liquefaction), and Gasification Research (hydrogen production from low-rank coals, advanced wastewater treatment, mild gasification, color and residual COD removal from Synfuel wastewaters, Great Plains Gasification Plant, gasifier optimization).

Optimal carbon tax with a dirty backstop: Oil, coal, or renewables?

OpenAIRE

van der Ploeg, Frederick; Withagen, Cees A.

2011-01-01

Optimal climate policy is studied. Coal, the abundant resource, contributes more CO2 per unit of energy than the exhaustible resource, oil. We characterize the optimal sequencing oil and coal and departures from the Herfindahl rule. "Preference reversal" can take place. If coal is very dirty compared to oil, there is no simultaneous use. Else, the optimal outcome starts with oil, before using oil and coal together, and finally coal on its own. The "laissez-faire" outcome uses coal forever or ...

Study on the coal mixing ratio optimization for a power plant

Science.gov (United States)

Jin, Y. A.; Cheng, J. W.; Bai, Q.; Li, W. B.

2017-12-01

For coal-fired power plants, the application of blended coal combustion has been a great issue due to the shortage and rising prices of high-rank coal. This paper describes the optimization of blending methods between Xing'an lignite coal, Shaltala lignite coal, Ura lignite coal, and Inner Mongolia bituminous coal. The multi-objective decision-making method based on fuzzy mathematics was used to determine the optimal blending ratio to improve the power plant coal-fired economy.

NOx, FINE PARTICLE AND TOXIC METAL EMISSIONS FROM THE COMBUSTION OF SEWAGE SLUDGE/COAL MIXTURES: A SYSTEMATIC ASSESSMENT

Energy Technology Data Exchange (ETDEWEB)

Jost O.L. Wendt

2002-08-15

This research project focuses on pollutants from the combustion of mixtures of dried municipal sewage sludge (MSS) and coal. The objective is to determine the relationship between (1) fraction sludge in the sludge/coal mixture, and (2) combustion conditions on (a) NOx concentrations in the exhaust, (b) the size segregated fine and ultra-fine particle composition in the exhaust, and (c) the partitioning of toxic metals between vapor and condenses phases, within the process. The proposed study will be conducted in concert with an existing ongoing research on toxic metal partitioning mechanisms for very well characterized pulverized coals alone. Both high NOx and low NOx combustion conditions will be investigated (unstaged and staged combustion). Tradeoffs between CO2 control, NOx control, and inorganic fine particle and toxic metal emissions will be determined. Previous research has yielded data on trace metal partitioning for MSS by itself, with natural gas assist, for coal plus MSS combustion together, and for coal alone. We have re-evaluated the inhalation health effects of ash aerosol from combustion of MSS both by itself and also together with coal. We have concluded that ash from the co-combustion of MSS and coal is very much worse from an inhalation health point of view, than ash from either MSS by itself or coal by itself. The reason is that ZnO is not the ''bad actor'' as had been suspected before, but the culprit is, rather, sulfated Zn. The MSS supplies the Zn and the coal supplies the sulfur, and so it is the combination of coal and MSS that makes that process environmentally bad. If MSS is to be burned, it should be burned without coal, in the absence of sulfur.

Mineral processing and characterization of coal waste to be used as fine aggregates for concrete paving blocks

Directory of Open Access Journals (Sweden)

C. R. Santos

Full Text Available Commercial coal production in the southern region of Brazil has been occurring since the beginning of the twentieth century. Due to the geological characteristics of the region, large amounts of solid wastes are generated. The aim of this work was to evaluate the use of coal waste to produce concrete paving blocks. A procedure to process the coal waste with the purpose of reducing the sulfur content and changing the particle size distribution of the material to meet the specification of fine aggregates was developed. The methodology considered the following steps: (a sampling of a coal mining waste; (b gravity separation of the fraction with specific gravity between 2.4 and 2.8; (c comminution of the material and particle size analysis; (d technological characterization of the material and production of concrete paving blocks; and (e acidity generation prediction (environmental feasibility. The results showed that the coal waste considered in this work can be used to replace conventional sand as a fine aggregate for concrete paving blocks in a proportion of up to 50%. This practice can result in cleaner coal production and reduce the demand for exploitation of sand deposits.

Engineering development of advance physical fine coal cleaning for premium fuel applications

Energy Technology Data Exchange (ETDEWEB)

Jha, M.C.; Smit, F.J.; Shields, G.L. [AMAX R& D Center/ENTECH Global Inc., Golden, CO (United States)

1995-11-01

The objective of this project is to develop the engineering design base for prototype fine coal cleaning plants based on Advanced Column Flotation and Selective Agglomeration processes for premium fuel and near-term applications. Removal of toxic trace elements is also being investigated. The scope of the project includes laboratory research and bench-scale testing of each process on six coals followed by design, construction, and operation of a 2 tons/hour process development unit (PDU). Three coals will be cleaned in tonnage quantity and provided to DOE and its contractors for combustion evaluation. Amax R&D (now a subsidiary of Cyprus Amax Mineral Company) is the prime contractor. Entech Global is managing the project and performing most of the research and development work as an on-site subcontractor. Other participants in the project are Cyprus Amax Coal Company, Arcanum, Bechtel, TIC, University of Kentucky and Virginia Tech. Drs. Keller of Syracuse and Dooher of Adelphi University are consultants.

POC-SCALE TESTING OF A DRY TRIBOELECTROSTATIC SEPARATOR FOR FINE COAL CLEANING

Energy Technology Data Exchange (ETDEWEB)

R.H. Yoon; G.H. Luttrell; E.S. Yan; A.D. Walters

2001-04-30

Numerous advanced coal cleaning processes have been developed in recent years that are capable of substantially reducing both ash- and sulfur-forming minerals from coal. However, most of the processes involve fine grinding and use water as the cleaning medium; therefore, the clean coal products must be dewatered before they can be transported and burned. Unfortunately, dewatering fine coal is costly, which makes it difficult to deploy advanced coal cleaning processes for commercial applications. As a means of avoiding problems associated with the fine coal dewatering, the National Energy Technology Laboratory (NETL) developed a dry coal cleaning process in which mineral matter is separated from coal without using water. In this process, pulverized coal is subjected to triboelectrification before being placed in an electric field for electrostatic separation. The triboelectrification is accomplished by passing a pulverized coal through an in-line mixer made of copper. Copper has a work function that lies between that of carbonaceous material (coal) and mineral matter. Thus, coal particles impinging on the copper wall lose electrons to the metal thereby acquiring positive charges, while mineral matter impinging on the wall gain electrons to acquire negative charges. The charged particles then pass through an electric field where they are separated according to their charges into two or more products depending on the configuration of the separator. The results obtained at NETL showed that it is capable of removing more than 90% of the pyritic sulfur and 70% of the ash-forming minerals from a number of eastern U.S. coals. However, the BTU recoveries were less than desirable. The laboratory-scale batch triboelectrostatic separator (TES) used by NETL relied on adhering charged particles on parallel electrode surfaces and scraping them off. Therefore, its throughput will be proportional to the electrode surface area. If this laboratory device is scaled-up as is, it would

Production of fines during co-combustion of coal with biomass fuels by fragmentation and attrition

Energy Technology Data Exchange (ETDEWEB)

I. Gulyurtlu; D. Boavida; H. Lopes (and others) [DEECA-INETI, Lisbon (Portugal)

2005-07-01

Results are reported from a project funded by the RFCS Programme of the European Union. The aim is to investigate, experimentally and by modeling, the production of fine char and ash particles during co-combustion of coal with wastes and biofuels in circulating fluidized bed. Work was undertaken at installations of different scales. Polish and Colombian coals were base fuels. The additional fuels were two sewage sludges. Bed temperature, feeding system, sand particle size, devolatilisation behaviour and char burn-out were studied to verify their influence on the fine particle production. Modeling was also carried out to understand the mechanisms of fragmentation and attrition. Samples from bed and cyclone were collected to determine particle size distributions. 11 refs.

Recovery of clean coal fines through a combination of gravity concentrator and flotation processes

Energy Technology Data Exchange (ETDEWEB)

Gupta, A.K.; Banerjee, P.K.; Dutta, A.; Mishra, A. [Tata Steel, Jamshedpur (India). Research & Development

2007-07-01

Flotation feed is a mixture of coarse and ultra-fine fractions. During conditioning of the flotation feed with collector and frother, the finer fraction consumes more reagents as compared to coarser particles. This is mainly due to more specific surface area of the ultra fine than the coarse fraction. This favors the adsorption of reagents toward ultra-finer fractions leads to less complete surface coverage of coarse particles and more entrainment of finer gangue particles. This results in the lower yield of coarse fractions from the flotation circuit and loss in selectivity. Hence, the major challenge is to improve the recovery of the coarser fraction and selectivity of ultra-fine fractions by improving flotation kinetics of all size fractions. This article deals with an approach to overcome the improper reagent adsorption by fine and coarse coal fractions in the flotation circuit through an innovative washing circuit containing gravity operation and flotation processes. Flotation performance between a new washing circuit having stub cyclone and flotation and normal single-stage reagent addition flotation process is compared in terms of selectivity, separation efficiency, rate constant, and size-wise recovery. The washing circuit having stub cyclone and flotation processes improves the fine clean coal yield by 10% and reduces the consumption of reagent compared to the normal single-stage reagent addition flotation process.

Compressive strength performance of OPS lightweight aggregate concrete containing coal bottom ash as partial fine aggregate replacement

Science.gov (United States)

Muthusamy, K.; Mohamad Hafizuddin, R.; Mat Yahaya, F.; Sulaiman, M. A.; Syed Mohsin, S. M.; Tukimat, N. N.; Omar, R.; Chin, S. C.

2018-04-01

Concerns regarding the negative impact towards environment due to the increasing use of natural sand in construction industry and dumping of industrial solid wastes namely coal bottom ash (CBA) and oil palm shell (OPS) has resulted in the development of environmental friendly lightweight concrete. The present study investigates the effect of coal bottom ash as partial fine aggregate replacement towards workability and compressive strength of oil palm shell lightweight aggregate concrete (OPS LWAC). The fresh and mechanical properties of this concrete containing various percentage of coal bottom ash as partial fine aggregate replacement were investigated. The result was compared to OPS LWAC with 100 % sand as a control specimen. The concrete workability investigated by conducting slump test. All specimens were cast in form of cubes and water cured until the testing age. The compressive strength test was carried out at 7 and 28 days. The finding shows that integration of coal bottom ash at suitable proportion enhances the strength of oil palm shell lightweight aggregate concrete.

Design, synthesis, and characterization of novel fine-particle, unsupported catalysts for coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

Klein, M.T.

1991-12-30

The purpose of this work is to investigate the kinetics-assisted design, synthesis and characterization of fme-pardcle, unsupported catalysts for coal liquefaction. The goal is to develop a fundamental understanding of coal catalysis and catalysts that will, in turn, allow for the specification of a novel optimal catalyst for coal liquefaction.

Study on the Relationship between the Inhalable Fine Particulate Matter of Xuanwei Coal Combustion and Lung Cancer

Directory of Open Access Journals (Sweden)

Jiapeng YANG

2015-07-01

Full Text Available Background and objective The high incidence of lung cancer in Xuanwei, China, has become an important restricting factor for livelihood development, thus exerting local social and economic impacts. Coal is the main fuel of the local community and also the main source of indoor pollution. This study aims to explore the coal combustion inhalable fine particulate matter (PM2.5 and its component output differences in different areas of Xuanwei, Yunnan. Moreover, the aim of this study is to investigate the relationship between inhalation of fine particles and high incidence of local lung cancer. Methods For combustion test, coal mines designated as C1, K7 and M30 were collected from LaoLin Colliery of Laibing Town, Huchang Colliery of Baoshan Town, and Taiping Colliery of Wenxing Town in Xuanwei, respectively. PM2.5 of indoor air was weighed, analyzed for elemental composition, and morphologically compared. The pathological specimen of lung cancer patients in Xuanwei who underwent operation was observed through electron microscope. Results The PM2.5 concentrations in indoor air were (8.244 ±1.460 mg/m3 (C1, (5.066±0.984 mg/m3 (K7, and (5.071±1.460 mg/m3 (M30. The differences among pairwise comparisons were statistically significant (P=0.029. The filter impurities of C1 coal seam primarily include Si- and O-enriched compounds. Moreover, three membranes that comprised other elements, including C, S, and Si, were observed. These membranes were evident from the aggregation of silica and a Ca-Al membrane. Compared with that of other coal seams, C1 coal generated a mass of impurities, in which several particles have irregular shape. We found nanoscale fine particles in some specimens of Xuanwei lung cancer patients. Conclusion The produced combustion of C1 coal was different from that of K7 and M30 coal. PM2.5 composition may be associated with the high local incidence of lung cancer.

The effect of sulphide and moisture content on steel corrosion during transport of fine wet coal

International Nuclear Information System (INIS)

Waanders, F. B.; Vorster, S. W.

2013-01-01

In the present investigation the influence of compaction pressure (stress) on the corrosivity of wet coal was investigated. Two coal samples, one high in sulphur content (3 %) and the other low in sulphur content (0.6 %) were used to determine the influence of compaction stress on the corrosion rates of steel samples in contact with compacted coal. It was found that the pressure exerted on finely divided wet coal is an important factor in determining its water content and corrosivity towards mild steel. Corrosion of the steel was typically in the form of pitting and the sulphur content of the coal was an important factor in determining the corrosivity of the coal. The corrosion rate of the high sulphur content coal was higher than that of the low sulphur coal. Mössbauer spectroscopy showed that a FeS species developed on the steel surface.

Measurements and simulation for design optimization for low NOx coal-firing system

Energy Technology Data Exchange (ETDEWEB)

E. Bar-Ziv; Y. Yasur; B. Chudnovsky; L. Levin; A. Talanker [Ben-Gurion University of Negev, Beer-Sheva (Israel)

2003-07-01

The information required to design a utility steam generator is the heat balance, fuel analysis and emission. These establish the furnace wall configuration, the heat release rates, and the firing technology. The furnace must be sized for (1) residence time for complete combustion with low NOx, and (2) reduction of flue gas temperature to minimize ash deposition. To meet these, computational fluid dynamics (CFD) of the combustion process in the furnace were performed and proven to be a powerful tool for this purpose. Still, reliable numerical simulations require careful interpretation and comparison with measurements. We report numerical results and measurements for a 575 MW pulverized coal tangential firing boiler of the Hadera power plant of Israel Electric Corporation (IEC). Measured and calculated values were found to be in reasonable agreement. We used the simulations for optimization and investigated temperature distribution, heat fluxes and concentration of chemical species. We optimized both the furnace flue gas temperature entering the convective path and the staged residence time for low NOx. We tested mass flow rates through close-coupled and separate overfire air ports and its arrangement and the coal powder fineness. These parameters can control the mixing rate between the fuel and the oxidizer streams and can affect the most important characteristics of the boiler such as temperature regimes, coal burning rate and nitrogen oxidation/reduction. From this effort, IEC started to improve the boiler performance by replacing the existing typical tangential burners to low NOx firing system to ensure the current regulation requirements of emission pollutions.

Dispersed-phase catalysis in coal liquefaction

International Nuclear Information System (INIS)

Utz, B.R.; Cugini, A.V.; Frommell, E.A.

1990-01-01

This paper reports that the specific reaction (activation) conditions for the conversion of catalyst precursors to unsupported catalyst have a direct effect on the catalytic activity and dispersion. The importance of reaction intermediates in decomposition of ammonium heptamolybdate and ammonium tetrathiomolybdate, and the sensitivity of these intermediates to reaction conditions, were studied in coal liquefaction systems. Recent results indicate that optimization of activation conditions facilitates the formation of a highly dispersed and active form of molybdenum disulfide for coal liquefaction. The use of the catalyst precursors ammonium heptamolybdate, ammonium tetrathiomolybdate, and molybdenum trisulfide for the conversion of coal to soluble products will be discussed. The use of an unsupported dispersed-phase catalyst for direct coal liquefaction is not a novel concept and has been employed in may studies with varying success. Dispersed-phase catalysts soluble and oil-soluble salts, and as finely divided powders. While some methods of catalyst introduction give higher dispersion of the catalyst and greater activity for the liquefaction of coal, all of the techniques allow the formation of a finely dispersed inorganic phase

Geochemistry of ultra-fine and nano-compounds in coal gasification ashes: A synoptic view

Energy Technology Data Exchange (ETDEWEB)

Kronbauer, Marcio A. [Centro Universitário La Salle, Mestrado em Avaliação de Impactos Ambientais em Mineração, Victor Barreto, 2288 Centro, 92010-000 Canoas, RS (Brazil); Universidade Federal do Rio Grande do Sul, Escola de Engenharia, Departamento de Metalurgia, Centro de Tecnologia, Av. Bento Gonçalves, 9500, Bairro Agronomia, CEP: 91501-970, Porto Alegre, RS (Brazil); Izquierdo, Maria [School of Applied Sciences, Cranfield University, Bedfordshire MK43 0AL (United Kingdom); Dai, Shifeng [State Key Laboratory of Coal Resources and Safe Mining, China University of Mining and Technology, Beijing 100083 (China); Waanders, Frans B. [School of Chemical and Minerals Engineering, North West University (Potchefstroom campus), Potchefstroom 2531 (South Africa); Wagner, Nicola J. [School of Chemical and Metallurgical Engineering, University of the Witwatersrand, Johannesburg (South Africa); Mastalerz, Maria [Indiana Geological Survey, Indiana University, Bloomington, IN 47405-2208 (United States); Hower, James C. [University of Kentucky Center for Applied Energy Research, 2540 Research Park Drive, Lexington, KY 40511 (United States); Oliveira, Marcos L.S. [Environmental Science and Nanotechnology Department, Catarinense Institute of Environmental Research and Human Development, IPADHC, Capivari de Baixo, Santa Catarina (Brazil); Taffarel, Silvio R.; Bizani, Delmar [Centro Universitário La Salle, Mestrado em Avaliação de Impactos Ambientais em Mineração, Victor Barreto, 2288 Centro, 92010-000 Canoas, RS (Brazil); and others

2013-07-01

The nano-mineralogy, petrology, and chemistry of coal gasification products have not been studied as extensively as the products of the more widely used pulverized-coal combustion. The solid residues from the gasification of a low- to medium-sulfur, inertinite-rich, volatile A bituminous coal, and a high sulfur, vitrinite-rich, volatile C bituminous coal were investigated. Multifaceted chemical characterization by XRD, Raman spectroscopy, petrology, FE-SEM/EDS, and HR-TEM/SEAD/FFT/EDS provided an in-depth understanding of coal gasification ash-forming processes. The petrology of the residues generally reflected the rank and maceral composition of the feed coals, with the higher rank, high-inertinite coal having anisotropic carbons and inertinite in the residue, and the lower rank coal-derived residue containing isotropic carbons. The feed coal chemistry determines the mineralogy of the non-glass, non-carbon portions of the residues, with the proportions of CaCO{sub 3} versus Al{sub 2}O{sub 3} determining the tendency towards the neoformation of anorthite versus mullite, respectively. Electron beam studies showed the presence of a number of potentially hazardous elements in nanoparticles. Some of the neoformed ultra-fine/nano-minerals found in the coal ashes are the same as those commonly associated with oxidation/transformation of sulfides and sulfates. - Highlights: • Coal waste geochemisty can provide increased environmental information in coal-mining areas. • Oxidation is the major process for mineral transformation in coal ashes. • The electron bean methodology has been applied to investigate neoformed minerals.

Synergistic Utilization of Coal Fines and Municipal Solid Waste in Coal-Fired Boilers. Phase I Final Report

Energy Technology Data Exchange (ETDEWEB)

V. Zamansky; P. Maly; M. Klosky

1998-06-12

A feasibility study was performed on a novel concept: to synergistically utilize a blend of waste coal fines with so-called E-fuel for cofiring and reburning in utility and industrial boilers. The E-fuel is produced from MSW by the patented EnerTech's slurry carbonization process. The slurry carbonization technology economically converts MSW to a uniform, low-ash, low-sulfur, and essentially chlorine-free fuel with energy content of about 14,800 Btu/lb.

Distinctive features of high-ash bituminuos coals combution with low milling fineness in furnace chambers with bottom blowing

Science.gov (United States)

Zroychikov, N. A.; Kaverin, A. A.; Biryukov, Ya A.

2017-11-01

Nowadays the problem of improvement of pulverized coal combustion schemes is an actual one for national power engineering, especially for combustion of coals with low milling fineness with significant portion of moisture or mineral impurities. In this case a big portion of inert material in the fuel may cause impairment of its ignition and combustion. In addition there are a lot of boiler installations on which nitrogen oxides emission exceeds standard values significantly. Decreasing of milling fineness is not without interest as a way of lowering an electric energy consumption for pulverization, which can reach 30% of power plant’s auxiliary consumption of electricity. Development of a combustion scheme meeting the requirements both for effective coal burning and environmental measures (related to NOx emission) is a complex task and demands compromising between these two factors, because implementation of NOx control by combustion very often leads to rising of carbon-in-ash loss. However widespread occurrence of such modern research technique as computer modeling allows to conduct big amount of variants calculations of combustion schemes with low cost and find an optimum. This paper presents results of numerical research of combined schemes of coal combustion with high portion of inert material based on straight-flow burners and nozzles. Several distinctive features of furnace aerodynamics, heat transfer and combustion has been found. The combined scheme of high-ash bituminouos coals combustion with low milling fineness, which allows effective combustion of pointed type of fuels with nitrogen oxides emission reduction has been proposed.

A LOW COST AND HIGH QUALITY SOLID FUEL FROM BIOMASS AND COAL FINES

Energy Technology Data Exchange (ETDEWEB)

John T. Kelly; George Miller; Mehdi Namazian

2001-07-01

Use of biomass wastes as fuels in existing boilers would reduce greenhouse gas emissions, SO2 and NOx emissions, while beneficially utilizing wastes. However, the use of biomass has been limited by its low energy content and density, high moisture content, inconsistent configuration and decay characteristics. If biomass is upgraded by conventional methods, the cost of the fuel becomes prohibitive. Altex has identified a process, called the Altex Fuel Pellet (AFP) process, that utilizes a mixture of biomass wastes, including municipal biosolids, and some coal fines, to produce a strong, high energy content, good burning and weather resistant fuel pellet, that is lower in cost than coal. This cost benefit is primarily derived from fees that are collected for accepting municipal biosolids. Besides low cost, the process is also flexible and can incorporate several biomass materials of interest The work reported on herein showed the technical and economic feasibility of the AFP process. Low-cost sawdust wood waste and light fractions of municipal wastes were selected as key biomass wastes to be combined with biosolids and coal fines to produce AFP pellets. The process combines steps of dewatering, pellet extrusion, drying and weatherizing. Prior to pilot-scale tests, bench-scale test equipment was used to produce limited quantities of pellets for characterization. These tests showed which pellet formulations had a high potential. Pilot-scale tests then showed that extremely robust pellets could be produced that have high energy content, good density and adequate weatherability. It was concluded that these pellets could be handled, stored and transported using equipment similar to that used for coal. Tests showed that AFP pellets have a high combustion rate when burned in a stoker type systems. While NOx emissions under stoker type firing conditions was high, a simple air staging approach reduced emissions to below that for coal. In pulverized-fuel-fired tests it was

Carbon burnout project-coal fineness effects

Energy Technology Data Exchange (ETDEWEB)

Mike Celechin [Powergen UK plc, Nottingham (United Kingdom)

2004-02-01

The aim of this DTI project is to establish good quality plant and rig data to demonstrate the effect of changing coal fineness on carbon burnout in a controlled manner, which can then be used to support computational fluid dynamics (CFD) and engineering models of the process. The modelling elements of the project were completed by Mitsui Babcock Energy Ltd., and validated using the data produced by the other partners. The full scale plant trials were successfully completed at Powergen's Kingsnorth Power Station and a full set of tests were also completed on Powergen's CTF. During these test both carbon-in-ash and NOx levels were seen to increase with increasing fuel particle size. Laboratory analysis of fly ash produced during the plant and rig trials revealed that only small differences in char morphology and reactivity could be detected in samples produced under significantly different operating conditions. Thermo Gravimetric Analysis was also undertaken on a range of PF size fractions collected form mills operating at different conditions. 3 refs., 13 figs., 1 tab.

Communication Optimizations for Fine-Grained UPCApplications

Energy Technology Data Exchange (ETDEWEB)

Chen, Wei-Yu; Iancu, Costin; Yelick, Katherine

2005-07-08

Global address space languages like UPC exhibit high performance and portability on a broad class of shared and distributed memory parallel architectures. The most scalable applications use bulk memory copies rather than individual reads and writes to the shared space, but finer-grained sharing can be useful for scenarios such as dynamic load balancing, event signaling, and distributed hash tables. In this paper we present three optimization techniques for global address space programs with fine-grained communication: redundancy elimination, use of split-phase communication, and communication coalescing. Parallel UPC programs are analyzed using static single assignment form and a data flow graph, which are extended to handle the various shared and private pointer types that are available in UPC. The optimizations also take advantage of UPC's relaxed memory consistency model, which reduces the need for cross thread analysis. We demonstrate the effectiveness of the analysis and optimizations using several benchmarks, which were chosen to reflect the kinds of fine-grained, communication-intensive phases that exist in some larger applications. The optimizations show speedups of up to 70 percent on three parallel systems, which represent three different types of cluster network technologies.

A study of Multistage/Multifunction Column for Fine Coal Cleaning CRADA PC93-005, Final Report; FINAL

International Nuclear Information System (INIS)

Ralph Lai; Shiao-Hung Chiang; Daxin He; Yuru Feng

1998-01-01

The overall objective of the this research project is to explore the potential applicability of a multistage column for fine coal cleaning and other applications in fluid particle separation. The research work identifies the design parameters and their effects on the performance of the separation device. The results of this study provide an engineering data basis for further development of this technology in coal cleaning and in general areas of fluid and particle separations

Optimization of palm kernel shell torrefaction to produce energy densified bio-coal

International Nuclear Information System (INIS)

Asadullah, Mohammad; Adi, Ag Mohammad; Suhada, Nurul; Malek, Nur Hanina; Saringat, Muhammad Ilmam; Azdarpour, Amin

2014-01-01

Highlights: • Around 70% of bio-coal yield was achieved from PKS torrefaction at 300 °C. • The higher heating value of optimized bio-coal was 24.5 MJ/kg. • Around 94% of thermal yield was achieved with 70% mass yield. • The grindability of optimized bio-coal was comparable with coal. - Abstract: Biomass torrefaction is a thermal process, which is similar to a mild form of pyrolysis at temperatures ranging from 200 to 320 °C to produce energy densified solid fuel. The torrefied biomass is almost equivalent to coal and is termed as bio-coal. During torrefaction, highly volatile fraction of biomass including moisture and hemicellulose are released as vapors, providing energy enriched solid fuel, which is hydrophobic and brittle. In this study, bio-coal is produced from palm kernel shell (PKS) in a batch feeding reactor. The operating variables such as temperature, residence time and swiping gas flow rate are optimized. Around 73% yield of bio-coal with calorific value of 24.5 MJ/kg was achieved at optimum temperature 300 °C with residence time of 20 min and nitrogen gas flow rate of 300 mL/min. The thermal yield was calculated to be maximum of 94% for the bio-coal produced at 300 °C. The temperature and residence time of torrefaction are found to be the most sensitive parameters in terms of product yield, calorific value and thermal yield of bio-coal

Characterization of seven United States coal regions. The development of optimal terrace pit coal mining systems

Energy Technology Data Exchange (ETDEWEB)

Wimer, R.L.; Adams, M.A.; Jurich, D.M.

1981-02-01

This report characterizes seven United State coal regions in the Northern Great Plains, Rocky Mountain, Interior, and Gulf Coast coal provinces. Descriptions include those of the Fort Union, Powder River, Green River, Four Corners, Lower Missouri, Illinois Basin, and Texas Gulf coal resource regions. The resource characterizations describe geologic, geographic, hydrologic, environmental and climatological conditions of each region, coal ranks and qualities, extent of reserves, reclamation requirements, and current mining activities. The report was compiled as a basis for the development of hypothetical coal mining situations for comparison of conventional and terrace pit surface mining methods, under contract to the Department of Energy, Contract No. DE-AC01-79ET10023, entitled The Development of Optimal Terrace Pit Coal Mining Systems.

Integrated coal preparation

International Nuclear Information System (INIS)

Buchanan, D.J.; Jones, T.F.

1992-01-01

Perceptions of quality have changed over the years. The attributes of a certain coal (its rank, slagging propensity, ash content etc) are traditionally referred to as its quality. However, the subject of this paper is quality in a much wider sense: quality as fitness for purpose: and all that such a wide definition entails. British Standard BS 5750 (ISO 9000) Quality Systems defines a systems approach to quality, and includes both the supplier of raw materials and the final customer within this boundary. Coal preparation starts at the production face. The greater the proportion of dirt in run-of-mine product the greater the challenge in satisfying the customer's needs. Significant advances have been made in minimizing mined dirt. For example, the sue of vertical steering on longwall faces improves productivity and quality. Unfortunately modern mining methods produce large quantities of fines, despite efforts to reduce them at the point of production and during transportation to the surface. Coal preparation also produces further fines. It has been estimated that fine coal costs 2.5 times as much to clean as large coal, and the costs of handing wet fine coal product will inflate this estimate. Handling considerations rightly concern our customers and are part of the wider meaning of quality. In this paper the authors address some novel solutions to the challenge posed by fines

Online analysis of coal on a conveyor belt by use of machine vision and kernel methods

Energy Technology Data Exchange (ETDEWEB)

Aldrich, C.; Jemwa, G.T.; van Dyk, J.C.; Keyser, M.J.; van Heerden, J.H.P. [University of Stellenbosch, Stellenbosch (South Africa). Dept. of Process Engineering

2010-07-01

The objective of this project is to explore the use of image analysis to quantify the amount of fines (6mm) present for different coal samples under conditions simulating the coal on conveyor belts similar to those being used by Sasol for gasification purposes. Quantification of the fines will be deemed particularly successful, if the fines mass fraction, as determined by sieve analysis, is possible to be predicted with an error of less than 10%. In this article, kernel-based methods to estimate particle size ranges on a pilot-scale conveyor belt as well as edge detection algorithms are considered. Preliminary results have shown that the fines fraction in the coal on the conveyor belt could be estimated with a median error of approximately 24.1%. This analysis was based on a relatively small number of sieve samples (18 in total) and needs to be validated by more samples. More samples would also facilitate better calibration and may lead to improved estimates of the sieve fines fractions. Similarly, better results may also be possible by using different approaches to image acquisition and analysis. Most of the error in the fines estimates can be attributed to sampling and to fines that were randomly obscured by the top layer (of larger particles) of coal on the belt. Sampling errors occurred as a result of some breakage of the coal between the sieve analyses and the acquisition of the images. The percentage of the fines obscured by the top layer of the coal probably caused most of the variation in the estimated mass of fines, but this needs to be validated experimentally. Preliminary studies have indicated that some variation in the lighting conditions have a small influence on the reliability of the estimates of the coal fines fractions and that consistent lighting conditions are more important than optimal lighting conditions.

Modeling and optimization of processes for clean and efficient pulverized coal combustion in utility boilers

Directory of Open Access Journals (Sweden)

Belošević Srđan V.

2016-01-01

Full Text Available Pulverized coal-fired power plants should provide higher efficiency of energy conversion, flexibility in terms of boiler loads and fuel characteristics and emission reduction of pollutants like nitrogen oxides. Modification of combustion process is a cost-effective technology for NOx control. For optimization of complex processes, such as turbulent reactive flow in coal-fired furnaces, mathematical modeling is regularly used. The NOx emission reduction by combustion modifications in the 350 MWe Kostolac B boiler furnace, tangentially fired by pulverized Serbian lignite, is investigated in the paper. Numerical experiments were done by an in-house developed three-dimensional differential comprehensive combustion code, with fuel- and thermal-NO formation/destruction reactions model. The code was developed to be easily used by engineering staff for process analysis in boiler units. A broad range of operating conditions was examined, such as fuel and preheated air distribution over the burners and tiers, operation mode of the burners, grinding fineness and quality of coal, boiler loads, cold air ingress, recirculation of flue gases, water-walls ash deposition and combined effect of different parameters. The predictions show that the NOx emission reduction of up to 30% can be achieved by a proper combustion organization in the case-study furnace, with the flame position control. Impact of combustion modifications on the boiler operation was evaluated by the boiler thermal calculations suggesting that the facility was to be controlled within narrow limits of operation parameters. Such a complex approach to pollutants control enables evaluating alternative solutions to achieve efficient and low emission operation of utility boiler units. [Projekat Ministarstva nauke Republike Srbije, br. TR-33018: Increase in energy and ecology efficiency of processes in pulverized coal-fired furnace and optimization of utility steam boiler air preheater by using in

Pre-Concentration of Vanadium from Stone Coal by Gravity Using Fine Mineral Spiral

Directory of Open Access Journals (Sweden)

Xin Liu

2016-08-01

Full Text Available Due to the low grade of V2O5 in stone coal, the existing vanadium extraction technologies face challenges in terms of large handling capacity, high acid consumption and production cost. The pre-concentration of vanadium from stone coal before the extraction process is an effective method to reduce cost. In this study, detailed mineral characterization of stone coal was investigated. It has been confirmed that the vanadium mainly occurs in muscovite and illite. A significant demand for an effective pre-concentration process with simple manipulation for discarding quartz and other gangue minerals is expected. Based on the mineralogical study, a new vanadium pre-concentration process using a fine mineral spiral was investigated. The experimental results showed that the separation process, which was comprised of a rougher and scavenger, could efficiently discard quartz, pyrite and apatite. A final concentrate with V2O5 grade of 1.02% and recovery of 89.6% could be obtained, with 26.9% of the raw ore being discarded as final tailings.

Too little oil, too much coal: Optimal carbon tax and when to phase in oil, coal and renewables

OpenAIRE

van der Ploeg, Frederick; Withagen, Cees A.

2011-01-01

Our main message is that it is optimal to use less coal and more oil once one takes account of coal being a backstop which emits much more CO2 than oil. The way of achieving this is to have a steeply rising carbon tax during the initial oil-only phase, a less-steeply rising carbon tax during the intermediate phase where oil and coal are used alongside each other and the following coal-only phase, and a flat carbon tax during the final renewables-only phase. The "laissez-faire" outcome uses co...

ANN-GA based optimization of a high ash coal-fired supercritical power plant

International Nuclear Information System (INIS)

Suresh, M.V.J.J.; Reddy, K.S.; Kolar, Ajit Kumar

2011-01-01

Highlights: → Neuro-genetic power plant optimization is found to be an efficient methodology. → Advantage of neuro-genetic algorithm is the possibility of on-line optimization. → Exergy loss in combustor indicates the effect of coal composition on efficiency. -- Abstract: The efficiency of coal-fired power plant depends on various operating parameters such as main steam/reheat steam pressures and temperatures, turbine extraction pressures, and excess air ratio for a given fuel. However, simultaneous optimization of all these operating parameters to achieve the maximum plant efficiency is a challenging task. This study deals with the coupled ANN and GA based (neuro-genetic) optimization of a high ash coal-fired supercritical power plant in Indian climatic condition to determine the maximum possible plant efficiency. The power plant simulation data obtained from a flow-sheet program, 'Cycle-Tempo' is used to train the artificial neural network (ANN) to predict the energy input through fuel (coal). The optimum set of various operating parameters that result in the minimum energy input to the power plant is then determined by coupling the trained ANN model as a fitness function with the genetic algorithm (GA). A unit size of 800 MWe currently under development in India is considered to carry out the thermodynamic analysis based on energy and exergy. Apart from optimizing the design parameters, the developed model can also be used for on-line optimization when quick response is required. Furthermore, the effect of various coals on the thermodynamic performance of the optimized power plant is also determined.

Integrating multi-objective optimization with computational fluid dynamics to optimize boiler combustion process of a coal fired power plant

International Nuclear Information System (INIS)

Liu, Xingrang; Bansal, R.C.

2014-01-01

Highlights: • A coal fired power plant boiler combustion process model based on real data. • We propose multi-objective optimization with CFD to optimize boiler combustion. • The proposed method uses software CORBA C++ and ANSYS Fluent 14.5 with AI. • It optimizes heat flux transfers and maintains temperature to avoid ash melt. - Abstract: The dominant role of electricity generation and environment consideration have placed strong requirements on coal fired power plants, requiring them to improve boiler combustion efficiency and decrease carbon emission. Although neural network based optimization strategies are often applied to improve the coal fired power plant boiler efficiency, they are limited by some combustion related problems such as slagging. Slagging can seriously influence heat transfer rate and decrease the boiler efficiency. In addition, it is difficult to measure slag build-up. The lack of measurement for slagging can restrict conventional neural network based coal fired boiler optimization, because no data can be used to train the neural network. This paper proposes a novel method of integrating non-dominated sorting genetic algorithm (NSGA II) based multi-objective optimization with computational fluid dynamics (CFD) to decrease or even avoid slagging inside a coal fired boiler furnace and improve boiler combustion efficiency. Compared with conventional neural network based boiler optimization methods, the method developed in the work can control and optimize the fields of flue gas properties such as temperature field inside a boiler by adjusting the temperature and velocity of primary and secondary air in coal fired power plant boiler control systems. The temperature in the vicinity of water wall tubes of a boiler can be maintained within the ash melting temperature limit. The incoming ash particles cannot melt and bond to surface of heat transfer equipment of a boiler. So the trend of slagging inside furnace is controlled. Furthermore, the

Process for agglomerating fine coal

Energy Technology Data Exchange (ETDEWEB)

Austin, L J; Misbach, P

1976-06-24

The invention concerns a process for agglomerating black coal in mud or powder form in the presence of a mineral oil product dispersed in water. During this process, the nutty slack is added to a portion - approximately 5 - 15% of its weight in the case of anhydrous coal - of a bitumen emulsion and thoroughly mixed. The emulsion should contain mineral oil bitumen with a penetration value 25/sup 0/ less than 5, or a Conradson value of over 35. In a further finishing process the emulsion contains alkaline naphthenate.

DEVELOPMENT AND DEMONSTRATION OF INTEGRATED CARBON RECOVERY SYSTEMS FROM FINE COAL PROCESSING WASTE

Energy Technology Data Exchange (ETDEWEB)

Y.P. Chugh; D. Patil; A. Patwardhan; R.Q. Honaker; B.K. Parekh; D. Tao; Latif Khan

2000-07-01

The project involves the development of an efficient, environmentally friendly system for the economical recovery of carbon from fine-coal refuse ponds. The project will be conducted in two phases. Phase I was involved in the development and evaluation of process equipment and techniques to be used in carbon recovery, product dewatering and reconstitution, and refuse management. Phase II will integrate the various units into a continuously operating circuit that will be demonstrated at a site selected based on the results presented in this study.

Coal beneficiation by gas agglomeration

Science.gov (United States)

Wheelock, Thomas D.; Meiyu, Shen

2003-10-14

Coal beneficiation is achieved by suspending coal fines in a colloidal suspension of microscopic gas bubbles in water under atmospheric conditions to form small agglomerates of the fines adhered by the gas bubbles. The agglomerates are separated, recovered and resuspended in water. Thereafter, the pressure on the suspension is increased above atmospheric to deagglomerate, since the gas bubbles are then re-dissolved in the water. During the deagglomeration step, the mineral matter is dispersed, and when the pressure is released, the coal portion of the deagglomerated gas-saturated water mixture reagglomerates, with the small bubbles now coming out of the solution. The reagglomerate can then be separated to provide purified coal fines without the mineral matter.

Clean fuel-magnesia bonded coal briquetting

Energy Technology Data Exchange (ETDEWEB)

Tosun, Yildirim I. [S. Demirel University Eng., Arch. Faculty Mining Eng. Department, Isparta (Turkey)

2007-10-15

Benefaction from coal fines as solid fuel in Turkey is very much important for economical development. Beneficiation from washed coal fines in the industry using solid fuel at lump size and in the municipal areas as an household solid fuel may be only provided by hot briquetting of the coal fines. The most practical common way of that benefication from coal fines in our country have been hot binding by sulfite liquor-sulfite liquor-melas and lime mixtures. Harmful the flue content of sulfite liquor-melas may only be eliminated by lime, a type of solid additive. However, cold bonded briquettes produced from coal fines are environmentally free. Just ash contents of these briquettes increase at a certain degree and heat content of them decrease at a certain extent. By using magnesia binder showed in this study, Tuncbilek lignite fines have been briquetted by cold and hot briquetting techniques. The qualities of briquettes produced by cold binders were compared with to those produced by other hot binding methods As a result, magnesia binder showed the similar characteristics with those of the briquettes produced by only cold bonded gypsum. Use of magnesite mixture and gypsum just as only cold binder was not suitable for the requirements from the coal briquettes to be used as solid fuels, particularly from household fuels, but just only as cold additive should be used. (author)

The influence of lisping material in pelletizing and agglomeration of fine coal pieces in laboratory conditions

International Nuclear Information System (INIS)

Vrencovski, Angele; Andreevski, Borche

1998-01-01

The work presents a part of laboratory results realized in academy of Firebug, carried on pelletizing and agglomeration of waste material, fine coal from thermal power station, using different lisping materials. Specially the influence of these materials in getting solid fuel, small briquette, formed by rolling press is analyzed. Special interest is attended to their characteristics: hardness and resistance. (Author)

Research on pyrolysis characteristics and kinetics of super fine and conventional pulverized coal

International Nuclear Information System (INIS)

Zhang Chaoqun; Jiang Xiumin; Wei Lihong; Wang Hui

2007-01-01

Based on isothermal thermogravimetric analysis (TGA) and kinetic equations, the optimization toolbox of MATLAB was applied to study the effects of particle size and heating rate on the pyrolysis characteristics and kinetics and to obtain the mechanism function and kinetic parameters of Yuanbaoshan coal at four different particle sizes and heating rates. The pyrolysis characteristics of the samples were analyzed using thermogravimetric (TG) curves and differential thermogravimetric (DTG) curves. The results show that the coal pyrolysis process is strongly affected by heating rate and particle size. As the heating rate increases, the temperature of volatile matter initiation increases, the total volatile matter evolved decreases and the DTG peak shifts toward higher temperature. As the particle size decreases, the temperature of volatile matter initiation of the coal sample decreases and the maximum rate of mass loss increases. In the pyrolysis of coal, the activation energies of the samples were found to increase with growing particle size and decreasing heating rate for both of the devolatilization temperature stages. In the lower temperature stage, the coal samples show a great difference in mechanism function at different particle sizes and heating rates

ELECTROKINETIC DENSIFICATION OF COAL FINES IN WASTE PONDS

Energy Technology Data Exchange (ETDEWEB)

E. James Davis

1999-12-18

The objective of this research was to demonstrate that electrokinetics can be used to remove colloidal coal and mineral particles from coal-washing ponds and lakes without the addition of chemical additives such as salts and polymeric flocculants. The specific objectives were: Design and develop a scaleable electrophoresis apparatus to clarify suspensions of colloidal coal and clay particles; Demonstrate the separation process using polluted waste water from the coal-washing facilities at the coal-fired power plants in Centralia, WA; Develop a mathematical model of the process to predict the rate of clarification and the suspension electrical properties needed for scale up.

Inclined fluidized bed system for drying fine coal

Science.gov (United States)

Cha, Chang Y.; Merriam, Norman W.; Boysen, John E.

1992-02-11

Coal is processed in an inclined fluidized bed dryer operated in a plug-flow manner with zonal temperature and composition control, and an inert fluidizing gas, such as carbon dioxide or combustion gas. Recycled carbon dioxide, which is used for drying, pyrolysis, quenching, and cooling, is produced by partial decarboxylation of the coal. The coal is heated sufficiently to mobilize coal tar by further pyrolysis, which seals micropores upon quenching. Further cooling with carbon dioxide enhances stabilization.

Optimal coal import strategy

International Nuclear Information System (INIS)

Chen, C.Y.; Shih, L.H.

1992-01-01

Recently, the main power company in Taiwan has shifted the primary energy resource from oil to coal and tried to diversify the coal supply from various sources. The company wants to have the imported coal meet the environmental standards and operation requirements as well as to have high heating value. In order to achieve these objectives, establishment of a coal blending system for Taiwan is necessary. A mathematical model using mixed integer programming technique is used to model the import strategy and the blending system. 6 refs., 1 tab

Process to dry and preheat fine-grained bituminous coal using non- or weakly baking coal and/or carbon materials. Verfahren zur Trocknung und Vorerhitzung von feinkoerniger Steinkohle unter Verwendung nicht oder nur schwach backender Kohle und/oder Kohlenstofftraegern

Energy Technology Data Exchange (ETDEWEB)

Echterhoff, J.; Frick, H.; Schaper, A.; Mohmeyer, H.

1982-11-04

Fine-grained bituminous coal is dried and preheated in an inert gas to prevent its oxidation. The inert gas consists essentially of steam which originates from the coal to be dried. The coal is heated besides by using steam intensively but gently. The drying is carried out in a drying drum in co-current flow. The coal is mixed with a binding agent in the presence of steam. The dried and preheated coal is taken out and, after being covered with a binding agent, transported without further safety measures to the atmosphere, stored and further processed. (KHH).

Multi - party Game Analysis of Coal Industry and Industry Regulation Policy Optimization

Science.gov (United States)

Jiang, Tianqi

2018-01-01

In the face of the frequent occurrence of coal mine safety accidents, this paper analyses the relationship between central and local governments, coal mining enterprises and miners from the perspective of multi - group game. In the actual production, the decision of one of the three groups can affect the game strategy of the other of the three, so we should assume the corresponding game order. In this order, the game analysis of the income and decision of the three is carried out, and the game decision of the government, the enterprise and the workers is obtained through the establishment of the benefit matrix and so on. And then on the existing system to optimize the coal industry regulation proposed practical recommendations to reduce the frequency of industry safety accidents, optimize the industry production environment.

Advanced physical fine coal cleaning spherical agglomeration. Final report

Energy Technology Data Exchange (ETDEWEB)

1990-09-01

The project included process development, engineering, construction, and operation of a 1/3 tph proof-of-concept (POC) spherical agglomeration test module. The POC tests demonstrated that physical cleaning of ultrafine coal by agglomeration using heptane can achieve: (1) Pyritic sulfur reductions beyond that possible with conventional coal cleaning methods; (2) coal ash contents below those which can be obtained by conventional coal cleaning methods at comparable energy recoveries; (3) energy recoveries of 80 percent or greater measured against the raw coal energy content; (4) complete recovery of the heptane bridging liquid from the agglomerates; and (5) production of agglomerates with 3/8-inch size and less than 30 percent moisture. Test results met or exceeded all of the program objectives. Nominal 3/8-inch size agglomerates with less than 20 percent moisture were produced. The clean coal ash content varied between 1.5 to 5.5 percent by weight (dry basis) depending on feed coal type. Ash reductions of the run-of-mine (ROM) coal were 77 to 83 percent. ROM pyritic sulfur reductions varied from 86 to 90 percent for the three test coals, equating to total sulfur reductions of 47 to 72 percent.

Optimization of laser-induced breakdown spectroscopy for coal powder analysis with different particle flow diameters

Energy Technology Data Exchange (ETDEWEB)

Yao, Shunchun, E-mail: epscyao@scut.edu.cn [School of Electric Power, South China University of Technology, Guangzhou, Guangdong 510640 (China); State Key Laboratory of Pulsed Power Laser Technology, Electronic Engineering Institute, Hefei 230037 (China); Xu, Jialong; Dong, Xuan; Zhang, Bo; Zheng, Jianping [School of Electric Power, South China University of Technology, Guangzhou, Guangdong 510640 (China); Lu, Jidong, E-mail: jdlu@scut.edu.cn [School of Electric Power, South China University of Technology, Guangzhou, Guangdong 510640 (China)

2015-08-01

The on-line measurement of coal is extremely useful for emission control and combustion process optimization in coal-fired plant. Laser-induced breakdown spectroscopy was employed to directly analyze coal particle flow. A set of tapered tubes were proposed for beam-focusing the coal particle flow to different diameters. For optimizing the measurement of coal particle flow, the characteristics of laser-induced plasma, including optical breakdown, the relative standard deviation of repeated measurement, partial breakdown spectra ratio and line intensity, were carefully analyzed. The comparison of the plasma characteristics among coal particle flow with different diameters showed that air breakdown and the random change in plasma position relative to the collection optics could significantly influence on the line intensity and the reproducibility of measurement. It is demonstrated that the tapered tube with a diameter of 5.5 mm was particularly useful to enrich the coal particles in laser focus spot as well as to reduce the influence of air breakdown and random changes of plasma in the experiment. - Highlights: • Tapered tube was designed for beam-focusing the coal particle flow as well as enriching the particles in laser focus spot. • The characteristics of laser-induced plasma of coal particle flow were investigated carefully. • An appropriate diameter of coal particle flow was proven to benefit for improving the performance of LIBS measurement.

Low-rank coal research. Final technical report, April 1, 1988--June 30, 1989, including quarterly report, April--June 1989

Energy Technology Data Exchange (ETDEWEB)

1989-12-31

This work is a compilation of reports on ongoing research at the University of North Dakota. Topics include: Control Technology and Coal Preparation Research (SO{sub x}/NO{sub x} control, waste management), Advanced Research and Technology Development (turbine combustion phenomena, combustion inorganic transformation, coal/char reactivity, liquefaction reactivity of low-rank coals, gasification ash and slag characterization, fine particulate emissions), Combustion Research (fluidized bed combustion, beneficiation of low-rank coals, combustion characterization of low-rank coal fuels, diesel utilization of low-rank coals), Liquefaction Research (low-rank coal direct liquefaction), and Gasification Research (hydrogen production from low-rank coals, advanced wastewater treatment, mild gasification, color and residual COD removal from Synfuel wastewaters, Great Plains Gasification Plant, gasifier optimization).

Coal washery effluent treatment for material recovery and water reuse

Energy Technology Data Exchange (ETDEWEB)

Banerjee, N.N.; Chaudhuri, M.

1980-10-01

Th effluent from coal washeries consisting mainly of coal fines is normally discharged to inland surface waters and causes severe river pollution with substantial loss of good quality coking coal. The study reported in this paper was undertaken to characterize the effluents from several coal washeries and to evaluate the potential of using various coagulants and coagulant aids for clarification of the effluent with a view to recovery of the coal fines and reuse of the clarified effluent. It has been demonstrated that higher recovery of coal fines can be achieved by using coagulants like alum or ferric chloride with or without coagulant aids with an added advantage of reuse of the clarified effluent in the washery.

Third symposium on coal preparation. NCA/BCR coal conference and Expo IV

Energy Technology Data Exchange (ETDEWEB)

None

1977-01-01

The third Symposium on Coal preparation, sponsored by the National Coal Association and Bituminous Coal Research, Inc., was held at the Kentucky Fair and Exposition Center, Louisville, Kentucky, October 18-20, 1977. Fourteen papers from the proceedings have been entered individually into EDB and ERA; five additional papers had been entered previously from other sources. Topics covered involved chemical comminution and chemical desulfurization of coal (aimed at reducing sulfur sufficiently with some coals to meet air quality standards without flue gas desulfurization), coal cleaning concepts, removing coal fines and recycling wash water, comparative evaluation of coal preparation methods, coal refuse disposal without polluting the environment, spoil bank reprocessing, noise control in coal preparation plants, etc. (LTN)

Optimal Tuning of Decentralized PI Controller of Nonlinear Multivariable Process Using Archival Based Multiobjective Particle Swarm Optimization

Directory of Open Access Journals (Sweden)

R. Kotteeswaran

2014-01-01

Full Text Available A Multiobjective Particle Swarm Optimization (MOPSO algorithm is proposed to fine-tune the baseline PI controller parameters of Alstom gasifier. The existing baseline PI controller is not able to meet the performance requirements of Alstom gasifier for sinusoidal pressure disturbance at 0% load. This is considered the major drawback of controller design. A best optimal solution for Alstom gasifier is obtained from a set of nondominated solutions using MOPSO algorithm. Performance of gasifier is investigated at all load conditions. The controller with optimized controller parameters meets all the performance requirements at 0%, 50%, and 100% load conditions. The investigations are also extended for variations in coal quality, which shows an improved stability of the gasifier over a wide range of coal quality variations.

Variation in mineral composition of coal during enrichment and coking

Energy Technology Data Exchange (ETDEWEB)

M.L. Ulanovskii; A.N. Likhenko [Ukrkoks Coke Producers' Association, Dnepropetrovsk (Ukraine)

2009-06-15

The parameters I{sub b} and B{sub b} used in developing an optimal coking-batch composition are determined from data on the chemical composition of the ash in Donetsk Basin and other coal. It is found that, when the ash content is reduced in deeper enrichment of coal with an increased content of fine pyrite, there will be accompanying increase in the Fe{sub 2}O{sub 3} content and decrease in the SiO{sub 2} content of the ash in lighter fractions. This increases I{sub b}. In other words, reducing the ash content of the coal is an unpromising means of increasing CRI and CSR of the coke produced. Three ash-containing elements (silicon, aluminum, and iron) are experimentally proven to transfer from coal to coke. Specific behavior of calcium, magnesium, alkali metals, and sulfur during coking.

The use of coal fines fly ash for the improvement of soils in hydrophobic grounds

International Nuclear Information System (INIS)

Janssen-Mommen, J.P.M.; Bestebroer, S.I.

1992-01-01

New NO x reducing combustion techniques result in a different physical and morphological quality of fly ash, which makes the use of fly ash less attractive for the building and road construction industries. Attention is paid to the possibility of using low-NO x fly ash for the improvement of the properties of hydrophobic agricultural land. Such an application also depends on the environmental impacts of the leaching of elements to the ground water and the accumulation of hazardous compounds in crops. A literature study of hydrophobic grounds was carried out. Also attention is paid to the legal aspects. No juridical constraints could be found in the Dutch legislation concerning the use of fly ash from coal powder, although it seems that the use of such fly ash is not in agreement with the tenor of possibly to be applied legislation. However, a small-scale investigation was carried out to gain insight into the environmental impacts. The uptake in lettuce and the leaching of the elements As, B, Mo and Se was studied by means of lysimeters. Hydrophobic soils with 5%, 10% and 15% coal fines fly ash were used. Also an experiment with the use of coal gasification slags was performed

Switching and optimizing control for coal flotation process based on a hybrid model

Science.gov (United States)

Dong, Zhiyong; Wang, Ranfeng; Fan, Minqiang; Fu, Xiang

2017-01-01

Flotation is an important part of coal preparation, and the flotation column is widely applied as efficient flotation equipment. This process is complex and affected by many factors, with the froth depth and reagent dosage being two of the most important and frequently manipulated variables. This paper proposes a new method of switching and optimizing control for the coal flotation process. A hybrid model is built and evaluated using industrial data. First, wavelet analysis and principal component analysis (PCA) are applied for signal pre-processing. Second, a control model for optimizing the set point of the froth depth is constructed based on fuzzy control, and a control model is designed to optimize the reagent dosages based on expert system. Finally, the least squares-support vector machine (LS-SVM) is used to identify the operating conditions of the flotation process and to select one of the two models (froth depth or reagent dosage) for subsequent operation according to the condition parameters. The hybrid model is developed and evaluated on an industrial coal flotation column and exhibits satisfactory performance. PMID:29040305

The Study of Cross-layer Optimization for Wireless Rechargeable Sensor Networks Implemented in Coal Mines

Science.gov (United States)

Ding, Xu; Shi, Lei; Han, Jianghong; Lu, Jingting

2016-01-01

Wireless sensor networks deployed in coal mines could help companies provide workers working in coal mines with more qualified working conditions. With the underground information collected by sensor nodes at hand, the underground working conditions could be evaluated more precisely. However, sensor nodes may tend to malfunction due to their limited energy supply. In this paper, we study the cross-layer optimization problem for wireless rechargeable sensor networks implemented in coal mines, of which the energy could be replenished through the newly-brewed wireless energy transfer technique. The main results of this article are two-fold: firstly, we obtain the optimal relay nodes’ placement according to the minimum overall energy consumption criterion through the Lagrange dual problem and KKT conditions; secondly, the optimal strategies for recharging locomotives and wireless sensor networks are acquired by solving a cross-layer optimization problem. The cyclic nature of these strategies is also manifested through simulations in this paper. PMID:26828500

Coal briquetting at the presence of humates as the binding substance

Directory of Open Access Journals (Sweden)

Zh. Arziev

2013-09-01

Full Text Available The results of coal briquetting at the presence of humates derived from coal at the stage of its chemical preparation by the extraction method are resulted in the paper. The conditions of briquetting and strength characteristics of the received briquettes are optimized. It is demonstrated that briquettes with the durability reaching 3 MPa can be derived from a coal fines using sodium, ammonium and silicate humates as binding substance. Water solutions of ammonium, sodium and silicate humates with concentration from 0,1-2% can be recommended for practical purposes. It is recommended to expose coal briquettes on a basis of ammonium humate to the thermal treatment at temperature 200°C as necessary of long storage (more than a year. The technological scheme of briquetting and the working project of creation of briquette factory with productivity of 40 000 tons of coal per year are developed.

Split and collectorless flotation to medium coking coal fines for multi-product zero waste concept

Energy Technology Data Exchange (ETDEWEB)

Dey, Shobhana; Bhattacharyya, K.K. [Mineral Processing Division, National Metallurgical Laboratory, Jamshedpur-831007 (India)

2007-06-15

The medium coking coal fines of - 0.5 mm from Jharia coal field were taken for this investigation. The release analysis of the composite coal reveals that yield is very low at 10.0% ash, about 25% at 14% ash and 50% at 17% ash level. The low yield is caused by the presence of high ash finer fraction. The size-wise ash analysis of - 0.5 mm coal indicated that - 0.5 + 0.15 mm fraction contains less ash than - 0.15 mm fraction. Thus, the composite feed was split into - 0.5 + 0.15 mm and - 0.15 mm fractions and subjected to flotation separately. The low ash bearing fraction (- 0.5 + 0.15 mm) was subjected to two stages collectorless flotation to achieve the concentrate with 10% ash. The cleaner concentrate (18.9%) with 10% ash was recovered which has an application in metallurgical industries. The concentrate of 30.2% yield with 12.5% ash could be achieved in one stage collectorless flotation which is suitable for use in coke making as sweetener. As the - 0.15 mm fraction contains relatively high ash, collector aided flotation using sodium silicate was performed to get a concentrate of 23.6% yield with about 17% ash. The blending of this product with cleaner tail obtained from - 0.5 + 0.15 mm produces about 35.0% yield with 17% ash and that can be utilized for coke making. The reject from the two fractions can be used for conventional thermal power plant or cement industries using a 23.5% ash after one stage collector aided flotation and the final tailings produced content ash of 61.6% can be used for fluidization combustion bed (FBC). This eventually leads to complete utilization of coal. (author)

Long range transport of fine particle windblown soils and coal fired power station emissions into Hanoi between 2001 to 2008

Energy Technology Data Exchange (ETDEWEB)

Cohen, D.D.; Crawford, J.; Stelcer, E.; Vuong, T.B. [Australian Nuclear Science & Technology Organisation, Kirrawee DC, NSW (Australia)

2010-10-15

Fine particulate matter (PM2.5), source fingerprints and their contributions have been measured and reported previously at Hanoi, Vietnam, from 25 April 2001 to 31 December 2008. In this study back trajectories are used to identify long range transport into Hanoi for two of these sources, namely, windblown dust (Soil) from 12 major deserts in China and emissions from 33 coal fired power plants (Coal) in Vietnam and China. There were 28 days of extreme Soil events with concentrations greater than 6 {mu} g m{sup -3} and 25 days of extreme Coal with concentrations greater than 30 {mu} g m{sup -3} from a total of 748 sampling days during the study period. Through the use of back trajectories it was found that long range transport of soil from the Taklamakan and Gobi desert regions (more than 3000 km to the north west) accounted for 76% of the extreme events for Soil. The three local Vietnamese power stations contributed to 15% of the extreme Coal events, while four Chinese power stations between 300 km and 1700 km to the north-east of Hanoi contributed 50% of the total extreme Coal events measured at the Hanoi sampling site.

A Pulverized Coal-Fired Boiler Optimized for Oxyfuel Combustion Technology

Directory of Open Access Journals (Sweden)

Tomáš Dlouhý

2012-01-01

Full Text Available This paper presents the results of a study on modifying a pulverized coal-fired steam boiler in a 250 MWe power plant for oxygen combustion conditions. The entry point of the study is a boiler that was designed for standard air combustion. It has been proven that simply substituting air by oxygen as an oxidizer is not sufficient for maintaining a satisfactory operating mode, not even with flue gas recycling. Boiler design optimization aggregating modifications to the boiler’s dimensions, heating surfaces and recycled flue gas flow rate, and specification of a flue gas recycling extraction point is therefore necessary in order to achieve suitable conditions for oxygen combustion. Attention is given to reducing boiler leakage, to which external pre-combustion coal drying makes a major contribution. The optimization is carried out with regard to an overall power plant conception for which a decrease in efficiency due to CO2 separation is formulated.

Water pollution profile of coal washeries

International Nuclear Information System (INIS)

Gupta, R.K.; Singh, Gurdeep

1995-01-01

Environmental problems in coal mining industry is increased with the demand of good quality of coal through coal washing/beneficiation activities. The coal washeries in general have been identified as one of the serious sources of water pollution particularly of Damodar river. Coal washeries though are designed on close water circuit, most of these however, fail to operate on close water circuit thus resulting in enormous quantity of effluents containing coal fines as well. This apart from posing serious water pollution problem also results into economic losses. The present study attempts to provide an insight into water pollution profile from coal washeries in Jharia coalfield. Various process parameters/unit operations in coal washing are also described. Effluents from various selected coal washeries of Jharia coalfield are sampled and analysed over a period of six months during 1993. Suspended solids, oil and grease and COD in the washery effluents are identified as the three major water quality parameters causing lots of concern for Damodar river pollution. Reasons for unavoidable discharge of effluents containing coal fines are also described. (author). 14 refs., 4 tabs., 2 figs

FINE PARTICAL AND TOXIC METAL EMISSIONS FROM THE COMBUSTION OF SEWAGE SLUDGE/COAL MIXTURES: A SYSTEMATIC ASSESSMENT

Energy Technology Data Exchange (ETDEWEB)

Jost O.L. Wendt; Wayne S. Seames; Art Fernandez

2003-09-21

This research project focuses on pollutants from the combustion of mixtures of dried municipal sewage sludge (MSS) and pulverized coal. The objective was to determine potential tradeoffs between CO{sub 2} mitigation through using a CO{sub 2} neutral fuel, such as municipal sewage sludge, and the emergence of other potential problems such as the emission of toxic fly ash particles. The work led to new insight into mechanisms governing the partitioning of major and trace metals from the combustion of sewage sludge, and mixtures of coal and sewage sludge. The research also showed that the co-combustion of coal and sewage sludge emitted fine particulate matter that might potentially cause greater lung injury than that from the combustion of either coal alone or municipal sewage sludge alone. The reason appeared to be that the toxicity measured required the presence of large amounts of both zinc and sulfur in particles that were inhaled. MSS provided the zinc while coal provided the sulfur. Additional research showed that the toxic effects could most likely be engineered out of the process, through the introduction of kaolinite sorbent downstream of the combustion zone, or removing the sulfur from the fuel. These results are consequences of applying ''Health Effects Engineering'' to this issue. Health Effects Engineering is a new discipline arising out of this work, and is derived from using a collaboration of combustion engineers and toxicologists to mitigate the potentially bad health effects from combustion of this biomass fuel.

Economical Optimization of the Mechanized Longwall Faces with Top Coal Caving Mining, In Horizontal Slices

Science.gov (United States)

Onica, Ilie; Mihăilescu, Viorel; Andrioni, Felicia

2016-09-01

To increase the economic and technical performances of the Jiu Valley hard coal mines, the top coal caving, in horizontal slices, mining methods (Bourbaki methods) were introduced, adapted to the local geo-mining conditions. This mining was successfully experimented by using classical technology, using the individual supports and coal blasting. In the future, it is planned to adopt the mechanized technology, with frame supports and shearers. The mechanized longwall faces with top coal caving mining, in horizontal slices, of coal seam no. 3 could be efficient only if the sizes of the top coal height and the panel length determine a minimum cost of production. Therefore, the goal of this paper is the optimization of these parameters, from a technical and economic point of view, taking into account the general model of the cost function, at the panel level. For that, it was necessary to make a certain sequence of analysis involving: technological unit establishment, purpose function and optimizing model. Thus, there attaining to the mathematical model of the unit cost, after determination of all the individual calculation articles, regarding the preparatory workings, coal face equipments, materials, energy, workforce, etc. Because of the complexity of the obtained technical and economic model, to determine the optimum sizes of the panel length and top coal height, it was necessary to archive a sensitivity analysis of the unit cost function to the main parameters implied into this mathematical model.

Optimization of coal recovery from open pits

Energy Technology Data Exchange (ETDEWEB)

Kim, C; Wolff, S F; Baafi, E Y; Cervantes, J A; Coates, D F

1979-02-01

The design techniques of the Pit Slope Manual were successfully applied in a case study concerned with optimizing the design of coal mines. A steeply dipping multiple seam deposit, being mined by the truck-shovel combination, was selected for the study. The criterion for optimum slopes was based on the financial consequences of each design, i.e., the resultant benefits and costs. Three alternative designs were analyzed. The first had an average highwall slope angle of 28 degrees and a final height of 290 m. The second had a 35 degrees slope angle and a 305-m wall height. The third had a 45 degrees slope angle and a 320-m wall height. Trade-off between benefits and increased cost of slope instability inherent in steeper slope angles was analyzed for the entire mine life through computer simulation of actual mining operations. The cost models developed were (1) No Cost, (2) Clean-up, (3) Lost Coal, (4) Early Mining, (5) Mine Abandonment, (6) Increased Haulage, and (7) Haul Road Re-establishment. (8 refs.)

Utilizing coal remaining resources and post-mining land use planning based on GIS-based optimization method : study case at PT Adaro coal mine in South Kalimantan

Directory of Open Access Journals (Sweden)

Mohamad Anis

2017-06-01

Full Text Available Coal mining activities may cause a series of environmental and socio-economic issues in communities around the mining area. Mining can become an obstacle to environmental sustainability and a major hidden danger to the security of the local ecology. Therefore, the coal mining industry should follow some specific principles and factors in achieving sustainable development. These factors include geological conditions, land use, mining technology, environmental sustainability policies and government regulations, socio-economic factors, as well as sustainability optimization for post-mining land use. Resources of the remains of the coal which is defined as the last remaining condition of the resources and reserves of coal when the coal companies have already completed the life of the mine or the expiration of the licensing contract (in accordance with government permission. This research uses approch of knowledge-driven GIS based methods mainly Analytical Hierarchy Process (AHP and Fuzzy logic for utilizing coal remaining resources and post-mining land use planning. The mining area selected for this study belongs to a PKP2B (Work Agreement for Coal Mining company named Adaro Indonesia (PT Adaro. The result shows that geologically the existing formation is dominated by Coal Bearing Formation (Warukin Formation which allows the presence of remains coal resource potential after the lifetime of mine, and the suitability of rubber plantation for the optimization of land use in all mining sites and also in some disposal places in conservation areas and protected forests.

Design, synthesis, and characterization of novel fine-particle, unsupported catalysts for coal liquefaction. Technical progress report, October 25, 1990--October 24, 1991: Draft

Energy Technology Data Exchange (ETDEWEB)

Klein, M.T.

1991-12-30

The purpose of this work is to investigate the kinetics-assisted design, synthesis and characterization of fme-pardcle, unsupported catalysts for coal liquefaction. The goal is to develop a fundamental understanding of coal catalysis and catalysts that will, in turn, allow for the specification of a novel optimal catalyst for coal liquefaction.

Coal to SNG: Technical progress, modeling and system optimization through exergy analysis

International Nuclear Information System (INIS)

Li, Sheng; Ji, Xiaozhou; Zhang, Xiaosong; Gao, Lin; Jin, Hongguang

2014-01-01

Highlights: • Technical progresses of coal to SNG technologies are reported. • The entire coal to SNG system is modeled. • Coupling between SNG production and power generation is investigated. • Breakthrough points for further energy saving are determined. • System performance is optimized based on the first and second laws of thermodynamics. - Abstract: For both energy security and CO 2 emission reduction, synthetic natural gas (SNG) production from coal is an important path to implement clean coal technologies in China. In this paper, an overview of the progress of coal to SNG technologies, including the development of catalysts, reactor designs, synthesis processes, and systems integration, is provided. The coal to SNG system is modeled, the coupling between SNG production and power generation is investigated, the breakthrough points for further energy savings are determined, and the system performance is optimized based on the first and the second laws of thermodynamics. From the viewpoint of the first law of thermodynamics, the energy conversion efficiency of coal to SNG system can reach 59.8%. To reduce the plant auxiliary power, the breakthrough points are the development of low-energy-consumption oxygen production technology and gas purification technology or seeking new oxidants for coal gasification instead of oxygen. From the viewpoint of the second law of thermodynamics, the major exergy destruction in a coal to SNG system occurs in the coal gasification unit, SNG synthesis unit and the raw syngas cooling process. How to reduce the exergy destruction in these units is the key to energy savings and system performance enhancement. The conversion ratio of the first SNG synthesis reactor and the split ratio of the recycle gas are key factors that determine the performance of both the SNG synthesis process and the whole plant. A “turning point” phenomenon is observed: when the split ratio is higher than 0.90, the exergy destruction of the SNG

Investigation of factors influencing the attrition breakage of coal

Energy Technology Data Exchange (ETDEWEB)

Oberholzer, V.; van der Walt, J. [North West University, Mmabatho (South Africa). School of Chemical & Minerals Engineering

2009-04-15

The presence of fines (particles smaller than 6 mm in diameter) causes hydrodynamic problems in gasifiers and therefore it is of great importance to minimize the amount of fine coal in the feed. This serves as motivation for understanding coal's breakage mechanisms, which could lead to the ability to predict the generation of fines. The aim of this project was to simulate the pulsating effect of the conveyor belt in order to investigate factors influencing the breakage. Results indicated that an increased initial particle size had an increasing effect in the amount of fines generated. Weathering had an insignificant effect on the breakage of coal. To conclude, a breakage model was developed to describe the rate of breakage out of the top size when a combination of two breakage modes is present.

Too Much Coal, Too Little Oil

OpenAIRE

Frederick van der Ploeg; Cees Withagen

2011-01-01

Optimal climate policy is studied. Coal, the abundant resource, contributes more CO2 per unit of energy than the exhaustible resource, oil. We characterize the optimal sequencing oil and coal and departures from the Herfindahl rule. "Preference reversal" can take place. If coal is very dirty compared to oil, there is no simultaneous use. Else, the optimal outcome starts with oil, before using oil and coal together, and finally coal on its own, The "laissez-faire" outcome uses coal forever or ...

Engineering development of advanced physical fine coal cleaning technologies - froth flotation

Energy Technology Data Exchange (ETDEWEB)

Ferris, D.D.; Bencho, J.R. [ICF Kaiser Engineers, Inc., Pittsburgh, PA (United States)

1995-11-01

In 1988, ICF Kaiser Engineers was awarded DOE Contract No. DE-AC22-88PC88881 to research, develop, engineer and design a commercially acceptable advanced froth flotation coal cleaning technology. The DOE initiative is in support of the continued utilization of our most abundant energy resource. Besides the goal of commercialability, coal cleaning performance and product quality goals were established by the DOE for this and similar projects. primary among these were the goals of 85 percent energy recovery and 85 percent pyrite rejection. Three nationally important coal resources were used for this project: the Pittsburgh No. 8 coal, the Upper Freeport coal, and the Illinois No. 6 coal. Following is a summary of the key findings of this project.

Fine coal cleaning via the micro-mag process

Science.gov (United States)

Klima, Mark S.; Maronde, Carl P.; Killmeyer, Richard P.

1991-01-01

A method of cleaning particulate coal which is fed with a dense medium slurry as an inlet feed to a cyclone separator. The coal particle size distribution is in the range of from about 37 microns to about 600 microns. The dense medium comprises water and ferromagnetic particles that have a relative density in the range of from about 4.0 to about 7.0. The ferromagnetic particles of the dense medium have particle sizes of less than about 15 microns and at least a majority of the particle sizes are less than about 5 microns. In the cyclone, the particulate coal and dense-medium slurry is separated into a low gravity product stream and a high gravity produce stream wherein the differential in relative density between the two streams is not greater than about 0.2. The low gravity and high gravity streams are treated to recover the ferromagnetic particles therefrom.

Geochemistry of coals, coal ashes and combustion wastes from coal-fired power stations

International Nuclear Information System (INIS)

Vassilev, S.V.; Vassileva, C.G.

1997-01-01

Contents, concentration trends, and modes of occurrence of 67 elements in coals, coal ashes, and combustion wastes at eleven Bulgarian thermoelectric power stations (TPS) were studied. A number of trace elements in coal and coal ash have concentrations greater than their respective worldwide average contents (Clarke values). Trace elements are concentrated mainly in the heavy accessory minerals and organic matter in coal. In decreasing order of significance, the trace elements in coal may occur as: element-organic compounds; impurities in the mineral matter; major components in the mineral matter; major and impurity components in the inorganic amorphous matter; and elements in the fluid constituent. A number of trace elements in the waste products, similar to coal ashes, exceed known Clarke contents. Trace elements are mainly enriched in non-magnetic, heavy and fine-grained fractions of fly ash. They are commonly present as impurities in the glass phases, and are included in the crystalline components. Their accessory crystalline phases, element-organic compounds, liquid and gas forms, are of subordinate importance. Some elements from the chalcophile, lithophile and siderophile groups may release into the atmosphere during coal burning. For others, the combustion process appears to be a powerful factor causing their relative enrichment in the fly ash and rarely in the bottom ash and slag. 65 refs., 1 fig., 11 tabs

How can we reduce carbon in ash in firing pulverized coal

Energy Technology Data Exchange (ETDEWEB)

O' Keefe, W. (and others)

1992-12-01

The article discusses solutions to the problem of reducing carbon in ash in firing pulverized coal. Suggested solutions to the problem include: reviewing air flow through the mills; examining the pulverizers for coal fineness variations; investigating air distribution in the burners; review dual-firing equations; examining the burners for slag build up; checking coal fineness is appropriate to the boiler; increasing air flow; and checking instrumentation. 2 figs., 1 photo.

Flocculation of chromite ore fines suspension using polysaccharide ...

Indian Academy of Sciences (India)

Unknown

liquid separation. Keywords. Flocculation; graft copolymer; mineral industry effluent; chromite ore fines; ... work well as flocculating agent on coal washery effluent, copper and iron ore fines etc (Karmakar et al 1998, 1999;. Tripathy et al 2001).

Production of fine coke from brown coal

Energy Technology Data Exchange (ETDEWEB)

Koenigs, H B

1977-08-01

The coke supply of the iron and steel industry, the design, function, and special features of the open-hearth are described, including coking properties and applications of the culm coke produced from brown coal. (In German)

Flotation process diagnostics and modelling by coal grain analysis

Energy Technology Data Exchange (ETDEWEB)

Ofori, P; O' Brien, G.; Firth, B.; Jenkins, B. [CSIRO Energy Technology, Brisbane, Qld. (Australia)

2006-05-15

In coal flotation, particles of different components of the coal such as maceral groups and mineral matter and their associations have different hydrophobicities and therefore different flotation responses. By using a new coal grain analysis method for characterising individual grains, more detailed flotation performance analysis and modelling approaches have been developed. The method involves the use of microscopic imaging techniques to obtain estimates of size, compositional and density information on individual grains of fine coal. The density and composition partitioning of coal processed through different flotation systems provides an avenue to pinpoint the actual cause of poor process performance so that corrective action may be initiated. The information on grain size, density and composition is being used as input data to develop more detailed flotation process models to provide better predictions of process performance for both mechanical and column flotation devices. A number of approaches may be taken to flotation modelling such as the probability approach and the kinetic model approach or a combination of the two. In the work reported here, a simple probability approach has been taken, which will be further refined in due course. The use of grain data to map the responses of different types of coal grains through various fine coal cleaning processes provided a more advanced diagnostic capability for fine coal cleaning circuits. This enabled flotation performance curves analogous to partition curves for density separators to be produced for flotation devices.

Multi-objective optimization of coal-fired power plants using differential evolution

International Nuclear Information System (INIS)

Wang, Ligang; Yang, Yongping; Dong, Changqing; Morosuk, Tatiana; Tsatsaronis, George

2014-01-01

Highlights: • Multi-objective optimization of large-scale coal-fired power plants using differential evolution. • A newly-proposed algorithm for searching the fronts of decision space in a single run. • A reduction of cost of electricity by 2–4% with an optimal efficiency increase up to 2% points. • The uncertainty comes mainly from temperature- and reheat-related cost factors of steam generator. • An exergoeconomic analysis and comparison between optimal designs and one real industrial design. - Abstract: The design trade-offs between thermodynamics and economics for thermal systems can be studied with the aid of multi-objective optimization techniques. The investment costs usually increase with increasing thermodynamic performance of a system. In this paper, an enhanced differential evolution with diversity-preserving and density-adjusting mechanisms, and a newly-proposed algorithm for searching the decision space frontier in a single run were used, to conduct the multi-objective optimization of large-scale, supercritical coal-fired plants. The uncertainties associated with cost functions were discussed by analyzing the sensitivity of the decision space frontier to some significant parameters involved in cost functions. Comparisons made with the aid of an exergoeconomic analysis between the cost minimum designs and a real industrial design demonstrated how the plant improvement was achieved. It is concluded that the cost of electricity could be reduced by a 2–4%, whereas the efficiency could be increased by up to two percentage points. The largest uncertainty is introduced by the temperature-related and reheat-related cost coefficients of the steam generator. More reliable data on the price prediction of future advanced materials should be used to obtain more accurate fronts of the objective space

Optimal operation for 3 control parameters of Texaco coal-water slurry gasifier with MO-3LM-CDE algorithms

Energy Technology Data Exchange (ETDEWEB)

Cao, Cuiwen; Zhang, Yakun; Gu, Xingsheng [Ministry of Education, East China Univ. of Science and Technology, Shanghai (China). Key Lab. of Advanced Control and Optimization for Chemical Processes

2013-07-01

Optimizing operation parameters for Texaco coal-water slurry gasifier with the consideration of multiple objectives is a complicated nonlinear constrained problem concerning 3 BP neural networks. In this paper, multi-objective 3-layer mixed cultural differential evolution (MO-3LM-CDE) algorithms which comprise of 4 multi-objective strategies and a 3LM-CDE algorithm are firstly presented. Then they are tested in 6 benchmark functions. Finally, the MO-3LM-CDE algorithms are applied to optimize 3 control parameters of the Texaco coal-water slurry gasifier in methanol production of a real-world chemical plant. The simulation results show that multi-objective optimal results are better than the respective single-objective optimal operations.

Optimization of hydrogen and syngas production from PKS gasification by using coal bottom ash.

Science.gov (United States)

Shahbaz, Muhammad; Yusup, Suzana; Inayat, Abrar; Patrick, David Onoja; Pratama, Angga; Ammar, Muhamamd

2017-10-01

Catalytic steam gasification of palm kernel shell is investigated to optimize operating parameters for hydrogen and syngas production using TGA-MS setup. RSM is used for experimental design and evaluating the effect of temperature, particle size, CaO/biomass ratio, and coal bottom ash wt% on hydrogen and syngas. Hydrogen production appears highly sensitive to all factors, especially temperature and coal bottom ash wt%. In case of syngas, the order of parametric influence is: CaO/biomass>coal bottom ash wt%>temperature>particle size. The significant catalytic effect of coal bottom ash is due to the presence of Fe 2 O 3 , MgO, Al 2 O 3 , and CaO. A temperature of 692°C, coal bottom ash wt% of 0.07, CaO/biomass of 1.42, and particle size of 0.75mm are the optimum conditions for augmented yield of hydrogen and syngas. The production of hydrogen and syngas is 1.5% higher in the pilot scale gasifier as compared to TGA-MS setup. Copyright © 2017 Elsevier Ltd. All rights reserved.

Estimation of Moisture Content in Coal in Coal Mills

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Mataji, B.

the moisture content of the coal is proposed based on a simple dynamic energy model of a coal mill, which pulverizes and dries the coal before it is burned in the boiler. An optimal unknown input observer is designed to estimate the moisture content based on an energy balance model. The designed moisture...

Estimation of Moisture Content in Coal in Coal Mills

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Mataji, Babak

2006-01-01

the moisture content of the coal is proposed based on a simple dynamic energy model of a coal mill, which pulverizes and dries the coal before it is burned in the boiler. An optimal unknown input observer is designed to estimate the moisture content based on an energy balance model. The designed moisture...

Optimized scheme in coal-fired boiler combustion based on information entropy and modified K-prototypes algorithm

Science.gov (United States)

Gu, Hui; Zhu, Hongxia; Cui, Yanfeng; Si, Fengqi; Xue, Rui; Xi, Han; Zhang, Jiayu

2018-06-01

An integrated combustion optimization scheme is proposed for the combined considering the restriction in coal-fired boiler combustion efficiency and outlet NOx emissions. Continuous attribute discretization and reduction techniques are handled as optimization preparation by E-Cluster and C_RED methods, in which the segmentation numbers don't need to be provided in advance and can be continuously adapted with data characters. In order to obtain results of multi-objections with clustering method for mixed data, a modified K-prototypes algorithm is then proposed. This algorithm can be divided into two stages as K-prototypes algorithm for clustering number self-adaptation and clustering for multi-objective optimization, respectively. Field tests were carried out at a 660 MW coal-fired boiler to provide real data as a case study for controllable attribute discretization and reduction in boiler system and obtaining optimization parameters considering [ maxηb, minyNOx ] multi-objective rule.

Detection of Coal Fires: A Case Study Conducted on Indian Coal Seams Using Neural Network and Particle Swarm Optimization

Science.gov (United States)

Singh, B. B.

2016-12-01

India produces majority of its electricity from coal but a huge quantity of coal burns every day due to coal fires and also poses a threat to the environment as severe pollutants. In the present study we had demonstrated the usage of Neural Network based approach with an integrated Particle Swarm Optimization (PSO) inversion technique. The Self Potential (SP) data set is used for the early detection of coal fires. The study was conducted over the East Basuria colliery, Jharia Coal Field, Jharkhand, India. The causative source was modelled as an inclined sheet like anomaly and the synthetic data was generated. Neural Network scheme consists of an input layer, hidden layers and an output layer. The input layer corresponds to the SP data and the output layer is the estimated depth of the coal fire. A synthetic dataset was modelled with some of the known parameters such as depth, conductivity, inclination angle, half width etc. associated with causative body and gives a very low misfit error of 0.0032%. Therefore, the method was found accurate in predicting the depth of the source body. The technique was applied to the real data set and the model was trained until a very good correlation of determination `R2' value of 0.98 is obtained. The depth of the source body was found to be 12.34m with a misfit error percentage of 0.242%. The inversion results were compared with the lithologs obtained from a nearby well which corresponds to the L3 coal seam. The depth of the coal fire had exactly matched with the half width of the anomaly which suggests that the fire is widely spread. The inclination angle of the anomaly was 135.510 which resembles the development of the geometrically complex fracture planes. These fractures may be developed due to anisotropic weakness of the ground which acts as passage for the air. As a result coal fires spreads along these fracture planes. The results obtained from the Neural Network was compared with PSO inversion results and were found in

Development of the electroacoustic dewatering (EAD) process for fine/ultrafine coal: Second quarterly progress report period ending 31 March 1989

Energy Technology Data Exchange (ETDEWEB)

None

1989-04-18

Battelle, in cooperation with the Electric Power Research Institute (EPRI), Ashbrook-Simon-Hartley (ASH), Kaiser Engineers (KE), Lewis Corporation, and Prof. S.H. Chiang of the University of Pittsburgh, is developing an advanced process for the dewatering of fine and ultrafine coals. The advanced process, called Electroacoustic Dewatering (EAD), capitalizes on the adaptation of synergistic effects of electric and acoustic fields to a commercial belt filter press design that is used in many other applications. The EAD equipment is described. 2 figs.

Computer application in coal preparation industry in China

Energy Technology Data Exchange (ETDEWEB)

Lu, M.; Wu, L.; Ni, Q. (China Univ. of Mining and Technology, Xuzhou (China))

1990-01-01

This paper describes several packages of microcomputer programs developed for designing and managing the coal preparation plants. Three parts are included: Coal Cleaning Package (CCP), Coal Preparation Optimization Program (CPO) and Coal Preparation Computer Aided Design System (CPCAD). The function of CCP is: evaluating and predicting coal cleaning result. Coal presentation process modelling and optimization; coal preparation flowsheet design and optimization. The CPO is a nonlinear optimization program. It can simulate and optimize the profit for different flowsheet to get the best combination of the final products. The CPCAD was developed based upon AutoCAD and makes full use of AutoLISP, digitizer menus and AutoCAD commands, combining the functions provided by AutoCAD and the principle used in conventional coal preparation plant design, forming a designer-oriented CPCAD system. These packages have proved to be reliable, flexible and easy to learn and use. They are a powerful tool for coal preparation plant design and management. (orig.).

Briquetting of Coke-Brown Coal Mixture

Directory of Open Access Journals (Sweden)

Ïurove Juraj

1998-09-01

Full Text Available The paper presents the results of the research of briquetting a coke-brown coal composite The operation consists of the feeding crushed coal and coke to moulds and pressing into briquettes which have been made in the Laboratories at the Mining Faculty of Technical University of Košice (Slovakia. In this research, all demands will be analyzed including the different aspects of the mechanical quality of briquettes, the proportion of fine pulverulent coal and coke in bricks, the requirements for briquetting the coke-brown coal materials.

ELECTROKINETIC DENSIFICATION OF COAL FINES IN WASTE PONDS

Energy Technology Data Exchange (ETDEWEB)

E. James Davis

1998-05-01

The objective of this research is to demonstrate that electrokinetics can be used to remove colloidal coal and mineral particles from coal-washing ponds and lakes without the addition of chemical additives such as salts and polymeric flocculants. In this experimental and analytical study the authors elucidate the transport processes that control the rate of concentrated colloidal particle removal, demonstrate the process on a laboratory scale, and develop the scale-up laws needed to design commercial-scale processes. The authors are also addressing the fundamental problems associated with particle-particle interactions (electrical and hydrodynamic), the effects of particle concentration on the applied electric field, the electrochemical reactions that occur at the electrodes, and the prediction of power requirements.

Optimizing wireless LAN for longwall coal mine automation

Energy Technology Data Exchange (ETDEWEB)

Hargrave, C.O.; Ralston, J.C.; Hainsworth, D.W. [Exploration & Mining Commonwealth Science & Industrial Research Organisation, Pullenvale, Qld. (Australia)

2007-01-15

A significant development in underground longwall coal mining automation has been achieved with the successful implementation of wireless LAN (WLAN) technology for communication on a longwall shearer. WIreless-FIdelity (Wi-Fi) was selected to meet the bandwidth requirements of the underground data network, and several configurations were installed on operating longwalls to evaluate their performance. Although these efforts demonstrated the feasibility of using WLAN technology in longwall operation, it was clear that new research and development was required in order to establish optimal full-face coverage. By undertaking an accurate characterization of the target environment, it has been possible to achieve great improvements in WLAN performance over a nominal Wi-Fi installation. This paper discusses the impact of Fresnel zone obstructions and multipath effects on radio frequency propagation and reports an optimal antenna and system configuration. Many of the lessons learned in the longwall case are immediately applicable to other underground mining operations, particularly wherever there is a high degree of obstruction from mining equipment.

Surface chemical problems in coal flotation

Science.gov (United States)

Taylor, S. R.; Miller, K. J.; Deurbrouck, A. W.

1981-02-01

As the use of coal increases and more fine material is produced by mining and processing, the need for improved methods of coal beneficiation increases. While flotation techniques can help meet these needs, the technique is beset with many problems. These problems involve surface chemical and interfacial properties of the coal-mineral-water slurry systems used in coal flotation. The problems associated with coal flotation include non-selectivity, inefficient reagent utilization, and excessive variablity of results. These problems can be broadely classified as a lack of predictability. The present knowledge of coal flotation is not sufficient, in terms of surface chemical parameters, to allow prediction of the flotation response of a given coal. In this paper, some of the surface chemical properties of coal and coal minerals that need to be defined will be discussed in terms of the problems noted above and their impact on coal cleaning.

FY 1980 Report on results of Sunshine Project by Coal Group. Basic researches on coal liquefaction techniques by solvolysis; 1980 nendo sunshine keikaku sekitanhan hokokusho. Sekitan no solvolysis ekika gijutsu no kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-07-01

The basic experimental researches were carried out for coal liquefaction by solvolysis. The studied items include hydrogenation conditions for treating the primary liquefied products, asphalt, pitch and model solvents (e.g., anthracene oil) in the presence of a commercial catalyst, solvolysis conditions for finely divided, molten coal using a hydrogenation recycled solvent, hydrotreating solvents, analysis of solvolysis-liquefied products, and liquefaction capacity of fractionated solvents for finely divided, molten coal. The studied items for separation of minerals include settlement at high temperature of the solid residue from the first liquefaction stage, and changed coal particle size distribution as a result of the first-stage liquefaction reactions in the presence of a hydrogenation solvent. The experimental study results indicate that conversion of finely divided molten coal into asphaltenes and preasphaltenes is notably accelerated in the phase-II coal liquefaction process by solvolysis, when a hydrotreating solvent is used for the first stage solvolysis process. (NEDO)

Source profiles of particulate matter emissions from a pilot-scale boiler burning North American coal blends.

Science.gov (United States)

Lee, S W

2001-11-01

Recent awareness of suspected adverse health effects from ambient particulate matter (PM) emission has prompted publication of new standards for fine PM with aerodynamic diameter less than 2.5 microm (PM2.5). However, scientific data on fine PM emissions from various point sources and their characteristics are very limited. Source apportionment methods are applied to identify contributions of individual regional sources to tropospheric particulate concentrations. The existing industrial database developed using traditional source measurement techniques provides total emission rates only, with no details on chemical nature or size characteristics of particulates. This database is inadequate, in current form, to address source-receptor relationships. A source dilution system was developed for sampling and characterization of total PM, PM2.5, and PM10 (i.e., PM with aerodynamic diameter less than 10 pm) from residual oil and coal combustion. This new system has automatic control capabilities for key parameters, such as relative humidity (RH), temperature, and sample dilution. During optimization of the prototype equipment, three North American coal blends were burned using a 0.7-megawatt thermal (MWt) pulverized coal-fired, pilot-scale boiler. Characteristic emission profiles, including PM2.5 and total PM soluble acids, and elemental and carbon concentrations for three coal blends are presented. Preliminary results indicate that volatile trace elements such as Pb, Zn, Ti, and Se are preferentially enriched in PM2.5. PM2.5 is also more concentrated in soluble sulfates relative to total PM. Coal fly ash collected at the outlet of the electrostatic precipitator (ESP) contains about 85-90% PM10 and 30-50% PM2.5. Particles contain the highest elemental concentrations of Si and Al while Ca, Fe, Na, Ba, and K also exist as major elements. Approximately 4-12% of the materials exists as soluble sulfates in fly ash generated by coal blends containing 0.2-0.8% sulfur by mass

Study on the Inference Factors of Huangling Coking Coal Pyrolysis

Science.gov (United States)

Du, Meili; Yang, Zongyi; Fan, Jinwen

2018-01-01

In order to reasonably and efficiently utilize Huangling coking coal resource, coal particle, heating rate, holding time, pyrolysis temperature and others factors were dicussed for the influence of those factor on Huangling coking coal pyrolysis products. Several kinds of coal blending for coking experiments were carried out with different kinds of coal such as Huangling coking coal, Xida coal with high ash low sufur, Xinghuo fat coal with hign sulfur, Zhongxingyi coking coal with high sulfur, Hucun lean coal, mixed meager and lean coal. The results shown that the optimal coal particle size distribution was 0.5~1.5mm, the optimal heating rate was 8°C/min, the optimal holding time was 15min, the optimal pyrolysis temperature was 800°C for Huangling coking coal pyrolysis, the tar yield increased from 4.7% to 11.2%. The maximum tar yield of coal blending for coking under the best single factor experiment condition was 10.65% when the proportio of Huangling coking coal was 52%.

Effect of mechanical and chemical clay removals by hydrocyclone and dispersants on coal flotation

Energy Technology Data Exchange (ETDEWEB)

Oats, W.J.; Ozdemir, O.; Nguyen, A.V. [University of Queensland, Brisbane, Qld. (Australia). School of Chemical Engineering

2010-04-15

Fine minerals, mostly clays, are known to have a detrimental effect on coal flotation. This paper focuses on the effect of mechanical and chemical removals of fine minerals by hydrocyclone and dispersants on coal flotation. The experimental results showed that the flotation recovery slightly increased from medium acidic to medium alkaline ranges. The flotation experiments carried out with dispersants at different dosages showed that the dispersants did not enhance the flotation recovery significantly. However, the removal of the fine fraction from the feed using a hydrocyclone significantly increased the flotation recovery. The bubble-particle attachment tests also indicated that the attachment time between an air bubble and the coal particles increased in the presence of clay particles. These attachment time results clearly showed that the clay particles adversely affected the flotation of coal particles by covering the coal surfaces which reduced the efficiency of bubble-coal attachment. An analysis based on the colloid stability theory showed that the clay coating was governed by the van der Waals attraction and that the double-layer interaction played a secondary role. It was also concluded that the best way to increase the flotation recovery in the presence of clays was to remove these fine minerals by mechanical means such as hydrocylones.

Biological removal of sulfur from coal flotation concentrate by culture isolated from coal washery plant tailing dump

Energy Technology Data Exchange (ETDEWEB)

Jorjani, E. [Azad University, Tehran (Iran). Mining Engineering Dept.

2005-10-15

A combination of flotation and microbial leaching processes was used to achieve acceptable level of sulfur and ash in Tabas coal sample of Iran. Representative sample of the minus 500 micron size fraction was subjected to flotation separation for the removal of ash and sulfur. The final concentrate with recovery, combustion value and sulfur content of 86.03, 86.45 and 1.35% respectively was achieved at pH 8 and following reagent dosage and operating conditions: collector: diesel oil (1200 g/ton), frother: MIBC (5%) + pine oil (95%) with concentration of 120 (g/ton), depressant: sodium silicate (1000 g/ton), particle size: {lt} 500 {mu} m and pulp density: 7%. Because of fine distribution of sulfur on Tabas coal macerals and lithotypes, high percentage of total sulfur (79.9%) is distributed in flotation concentrate and only 20.1% is yielded in the tails. So microbial leaching using a species isolated from coal washery plant tailing dump was used in batch system to remove sulfur from flotation concentrate. The conditions were optimized for the maximum removal of sulfur. These conditions were found to be pH of 2, particle size less than 0.18 mm; pulp density: 8%, temperature: 30 {sup o}C, shaking rate: 150 rpm conditions. Total sulfur and ash content was reduced by bioleaching from 13.55 and 1.35 in flotation concentrate to 9.47 and 0.55 in the final leached concentrate, a reduction of 35 and 61.9% respectively. Sterilization of coal adversely affects the sulfur reduction. The results suggest that the isolated culture is sufficiently effective for depyritization of Tabas coal flotation concentrate in stirred system.

A Gas–Solid–Liquid Coupling Model of Coal Seams and the Optimization of Gas Drainage Boreholes

Directory of Open Access Journals (Sweden)

Yuexia Chen

2018-03-01

Full Text Available For a gas–solid–liquid coupling model of coal seams, previous permeability models basically supposed uniaxial strains as the boundary condition for coal reservoirs without considering the deformation caused by changes in humidity. The permeability model varies under different boundary conditions. According to the true triaxial stress state of coal reservoirs, a permeability model considering the effective stress, sorption and desorption, and wet strain was established. Based on the permeability model, the continuity equation of gas and water and the stress field equation were coupled. Then, the model was incorporated in the COMSOL suite to simulate gas drainage from boreholes in floor roadways passing through seams in a coal mine. By comparing with the measured gas flow on site, the model was verified as being reliable. Moreover, the spacing and layout shape of boreholes in floor roadways were simulated. To achieve the aim of eliminating regional outburst within 180 days and decreasing the number of boreholes so as to reduce the cost, the spacing and shape of boreholes were optimized. When the superimposed effect of the boreholes was not considered, the optimal spacing of boreholes was 3 r; if the superimposed effect was taken into account, the spacing could be set to within 3 r ≤ L ≤ R, where r and R represent the effective gas drainage radius and the influence radius of gas drainage, respectively. The borehole spacing could be appropriately increased when the boreholes were arranged in rhomboidal form. To achieve the same range of outburst elimination, the rhomboidal layout can decrease the number of boreholes to reduce cost, thus realizing the objective of this optimization process.

A fine art

Energy Technology Data Exchange (ETDEWEB)

Schnabel, G.; Raaff, T. [Andritz AG (Austria)

2006-07-15

The paper describes a new dewatering system for coal fines which challenges established processes by using screenbowl centrifuge and hyperbaric filter combinations. Company acquisitions over the past three to four years enabled Andritz AG to develop a new system combining two technologies. The article describes the benefits of the combination process and explains the basic operation of these machines. 4 figs.

Profit from plant experience in specifying coal conveyors

Energy Technology Data Exchange (ETDEWEB)

Rajter, L C

1985-09-01

Most coal conveyors in operation today were designed to handle raw unwashed coal and are experiencing difficulties when dealing with fine, wet coal which has been cleaned. Conveyor designers should base their designs for new systems on the worst possible materials. Design criteria are discussed in detail and recommendations made for chute liners and radii, skirt system, belt speed, transfer points, belt wipers, weather protection and access. 3 references.

Impacts of Natural Surfactant Soybean Phospholipid on Wettability of High-rank Coal Reservoir

Science.gov (United States)

Lyu, S.; Xiao, Y.; Yuan, M.; Wang, S.

2017-12-01

It is significant to change the surface wettability of coal rock with the surfactant in coal mining and coalbed methane exploitation. Soybean phospholipid (SP) is a kind of natural zwitterionic surfactant which is non-toxic and degradable. In order to study the effects of soybean phospholipid on wettability of high-rank coal in Qinshui Basin, some experiments including surface tension test, contact angle measurement on the coal surface, coal fines imbibition, observation of dispersion effect and gas permeability test were carried out, and water locking mechanism of fracturing fluid in micro fractures of coal reservoir was analyzed. The results show that the surface of high-rank coal was negatively charged in solution and of weak hydrophilicity. The soybean phospholipid with the mass fraction of 0.1% reduced the surface tension of water by 69%, and increased the wettability of coal. Meanwhile, the soybean phospholipid helped coal fines to disperse by observation of the filter cake with the scanning electron microscope. The rising rate of soybean phospholipid solution in the pipe filled with coal fines was lower than that of anionic and cationic surfactant, higher than that of clean water and non-ionic surfactant. Composite surfactant made up of soybean phospholipid and OP-10 at the ratio of 1:3 having a low surface tension and large contact angle, reduced the capillary force effectively, which could be conducive to discharge of fracturing fluid from coal reservoir micro fracture and improve the migration channels of gas. Therefore it has a broad application prospect.

Characterisation of coal washery effluent and optimisation of coagulation behaviour of Moringa oleifera seed as a coagulant.

Science.gov (United States)

Kapse, Gaurav; Patoliya, Pruthvi; Samadder, S R

2017-03-01

The huge quantity of effluent generated in coal washing processes contains large amount of suspended and dissolved solids, clay minerals, coal fines and other impurities associated with raw coal. The present system of recirculation of the effluent is found to be ineffective in removing colloidal fines, which is the major part of the impurities present in washery effluent. Hence, there is a need for the assessment of a better technique for an efficient removal of these impurities. This study deals with detailed characterisation of coal washery effluent and fine particles present in it. For efficient removal of impurities, the suitability of biocoag-flocculation process using Moringa oleifera seed biomass as a natural coagulant was examined. Various doses of M. oleifera ranging from 0.2 to 3 mL/L were used in order to determine the optimal conditions. The impact of the variations in pH of the effluent (2-10), contact time (5-30 min), settlement time (5-50 min), temperature (10-50 °C) and the effluent dilution (1:0-1:5) was also assessed to optimise the treatment process. Post treatment analysis was carried out for determination of the different parameters such as pH, conductivity, turbidity, solids and settling velocity. Excellent reduction in turbidity (97.42%) and suspended solids (97.78%) was observed at an optimum dose of M. oleifera seed coagulant of 0.8 mL/L with an optimum contact time of 15 and at 20 min of settling time. In comparison with very few past studies of M. oleifera in the treatment of coal washery effluent with high dose and inadequate removal, this study stands to be a major highlight with low dose and high removal of the impurities. M. oleifera coagulant is considered to be an environment-friendly material, therefore, its application is recommended for simple and efficient treatment of coal washery effluent.

Coal flotation optimization using modified flotation parameters and combustible recovery in a Jameson cell

International Nuclear Information System (INIS)

Vapur, Hueseyin; Bayat, Oktay; Ucurum, Metin

2010-01-01

This study discusses a new coal flotation optimization approach. It is conducted using modified flotation parameters and combustible recovery. The experimental work was evaluated in two stages. In the first stage, recoveries (1, 2, 3, 5 and 8 min of flotation times) of Jameson flotation operating parameters were fitted to first-order kinetic model, R = R ∞ [1 - exp (-kt)] where R was recovery at t time, R ∞ was ultimate recovery and k was the first-order rate constant to draw the time recovery curves in the experimental study. Two parameters, the ultimate recovery (R ∞ ) and first-order rate constant (k), were then obtained from the model to fit an experimental time recovery curve. A modified flotation rate constant (K m ) defined as product of R ∞ and k, i.e., K m = R ∞ * k, and selectivity index (SI) defined as the ratio of the modified rate constant of coal to the modified rate constant of ash (SI)=K m of Coal/K m of Ash), which could be collectively called 'modified flotation parameters'. It was used to determine of the sub and upper values of operation variables. In the second one, combustible recovery (%) and ash content (%) were used to optimization of the Jameson flotation variables and it was found that d 80 = 0.250 mm particle size, 1/1 vegetable oil acids/kerosene ratio, 20% solids pulp density, 0.600 L/min wash water rate and 40 cm downcomer immersion dept could be used to separate efficiently coal from ash. Final concentrate was obtained with 94.83% combustible recovery and 17.86% ash content at optimum conditions after 8 min flotation time.

Peak capacity analysis of coal power in China based on full-life cycle cost model optimization

Science.gov (United States)

Yan, Xiaoqing; Zhang, Jinfang; Huang, Xinting

2018-02-01

13th five-year and the next period are critical for the energy and power reform of China. In order to ease the excessive power supply, policies have been introduced by National Energy Board especially toward coal power capacity control. Therefore the rational construction scale and scientific development timing for coal power are of great importance and paid more and more attentions. In this study, the comprehensive influence of coal power reduction policies is analyzed from diverse point of views. Full-life cycle cost model of coal power is established to fully reflect the external and internal cost. Then this model is introduced in an improved power planning optimization theory. The power planning and diverse scenarios production simulation shows that, in order to meet the power, electricity and peak balance of power system, China’s coal power peak capacity is within 1.15 ∼ 1.2 billion kilowatts before or after 2025. The research result is expected to be helpful to the power industry in 14th and 15th five-year periods, promoting the efficiency and safety of power system.

Revegetation on a coal fine ash disposal site in South Africa

Energy Technology Data Exchange (ETDEWEB)

Van Rensburg, L.; De Sousa Correia, R.I.; Booysen, J. [Potchefstroom Univ. for Christian Higher Education (South Africa). Research Inst. for Reclamation Ecology; Ginster, M. [Sastech Research and Development, Sasolburg (South Africa)

1998-11-01

Eight medium amendments were conducted on top of a fine ash coal dump (i) to evaluate a few cost-effective treatments that could determine the minimum fertility status required for the local ash to support the establishment of a viable vegetation cover, and (ii) to select suitable grass species that would establish on the ash and could serve as a foundation for long-term rehabilitation. Degree and success of grass establishment per medium amelioration treatment is expressed in terms of total biomass, percentage basal cover, and in terms of a condition assessment model. Both the chemical and physical nature of the ash medium before and after amendment was characterized, as were the concentrations of some essential and potentially toxic elements in leaf samples. In terms of medium amelioration 5000 kg ha{sup {minus}1} compost, or 500 kg ha{sup {minus}1} kraal manure or 480 kg 2:3:2 ha{sup {minus}1} proved to be most effective. The grass species that occurred with the highest frequency, irrespective of treatment, were the perennials bermudagrass [Cynodon dactylon (L.) pers. var dactylon], weeping lovegrass [Eragrostis curvula (Schrader) Nees], and the annual teff [Eragrostis tef (Zuccagni) Trotter]. Of the potentially toxic extractable metals monitored in the leaves of vegetation on the dump, only Se accumulated to an average level of 4.4 mg kg{sup {minus}1} that could be toxic to livestock.

Microwave treatment of a brown coal concentrate from Mugunsk coal for the manufacture of sponge iron

Energy Technology Data Exchange (ETDEWEB)

A.A. Khaidurova; P.N. Konovalov; N.P. Konovalov [Irkutsk State Technical University, Irkutsk (Russia)

2008-04-15

A technique for the production of a finely dispersed dry brown coal concentrate with the use of microwave energy is proposed to prepare a charge mixture for the manufacture of sponge iron. The advantages of this technique over analogous industrial processes are demonstrated. The results of experiments on the briquetting of the charge mixture of brown coal and iron ore concentrates without the use of an additional binding agent are described.

A complex of optimization problems in planning for the development of mining operations in coal mines

Energy Technology Data Exchange (ETDEWEB)

Todorov, A K; Arnaudov, B K; Brankova, B A; Gyuleva, B I; Zakhariyev, G K

1977-01-01

The system for planning for the development of coal mines is a complex of interrelated plan optimization, plan calculation and supporting (accounting-analytical and standards) tasks. An important point in this complex is held by the plan optimization tasks. The questions about the synthesis and the structural peculiarities of the system, the essence and machine realization of the tasks are examined.

Research of Heating Rates Influence on Layer Coal Gasification of Krasnogorsky And Borodinsky Coal Deposit

Directory of Open Access Journals (Sweden)

Jankovskiy Stanislav

2015-01-01

Full Text Available Experimental research of heating rate influence on coal samples gasification process of Krasnogorsky and Borodinsky coal deposit ranks A and 2B was done to define optimal heating mode in high intensification of dispersal of inflammable gases conditions. Abundance ratio of carbon monoxide and nitrogen monoxide, water vapor, carbon dioxide at four values of heating rate within the range of 5 to 30 K/min. with further definition of optimal heating rate of coals was stated.

Process for hydrogenating coal and coal solvents

Science.gov (United States)

Tarrer, Arthur R.; Shridharani, Ketan G.

1983-01-01

A novel process is described for the hydrogenation of coal by the hydrogenation of a solvent for the coal in which the hydrogenation of the coal solvent is conducted in the presence of a solvent hydrogenation catalyst of increased activity, wherein the hydrogenation catalyst is produced by reacting ferric oxide with hydrogen sulfide at a temperature range of 260.degree. C. to 315.degree. C. in an inert atmosphere to produce an iron sulfide hydrogenation catalyst for the solvent. Optimally, the reaction temperature is 275.degree. C. Alternately, the reaction can be conducted in a hydrogen atmosphere at 350.degree. C.

Characterization of a coal tailing deposit for zero waste mine in the Brazilian coal field of Santa Catarina

International Nuclear Information System (INIS)

Amaral Filho, J.R.; Schneider, I.A.H.; Tubino, R.M.C.; Brum de, I.A.S.; Miltzarek, G.; Sampaio, C.H.

2010-01-01

Coal tailings deposits in Brazil are occupying large areas of land while also generating acid mine drainage (AMD) that includes heavy metals. This paper described an analytical study of a typical coal tailings deposit. The study objective was to separate low density, intermediate density, and high density fractions for future reuse. Particle size analysis, disymmetric studies, X-ray diffraction, and tests conducted to determine ash, total sulphur, and acid bases were conducted in order to characterize the coal tailings samples. Results of the study demonstrated a size distribution of 67 percent coarse, 14 percent fine, and 19 percent ultra-fine particles. The gravimetric concentration method was used to recover 34.2 percent of the total deposit for future energy use. Approximately 9.2 percent of the remaining deposit was a pyrite concentrate. The acid generating potential of the remaining materials was reduced by approximately 60 percent. 9 refs., 1 tab., 2 figs.

Hazards from radioactivity of fly ash of Greek coal power plants (CPP)

International Nuclear Information System (INIS)

Papastefanou, C.; Charalambous, S.

1980-01-01

Fly ash and fine dispersion releases from coal combustion in Greek coal power plants were studied. Concentrations in the fly ash up to 20 pCi/g and 10 pCi/g were measured for 238 U and 226 Ra respectively (not in secular equilibrium). Risk from the fly ash derives from its escape in particulate form or fine dispersion and from its use as a substitute for cement in concrete. The new data indicate that coal power plants discharge relatively larger quantities of radioactive material into the atmosphere than nuclear power plants of comparable size, during normal operation. (H.K.)

Combined production of synthetic liquid fuel and electricity from coal using H2S and CO2 removal systems

Directory of Open Access Journals (Sweden)

Elina A. Tyurina

2015-11-01

Full Text Available The main aim of the research is to continue the studies on promising technologies of coal conversion into synthetic liquid fuel (methanol. The object of study is the plants for combined production of electricity and synthetic liquid fuel (PCPs, which are eco-friendly and more efficient as compared to the plants for separate production. The previous studies on PCPs consider the systems for fine cleaning of gasification products in a simplified way. This study presents the detailed mathematical modeling of the aforementioned systems and determines the values of energy consumption and investment in them. The obtained values are used to carry out the optimization studies and find the optimal parameters of PCPs with different degree of CO2 removal from gasification products providing fine cleaning of gasification products from H2S.

Treating effluents; recovering coal, etc

Energy Technology Data Exchange (ETDEWEB)

Jones, F B; Bury, E

1920-02-18

Liquor obtained by scrubbing coal gas with sea-water or fresh water, and containing or having added to it finely-divided carbonaceous material in suspension, is subjected to a froth-flotation process to recover the carbonaceous matter and organic materials in the froth, and render the remaining liquor innocuous. Liquor obtained by scrubbing distillation gases, such as coal gas, may be used as a frothing-agent in a froth flotation process for the recovery of carbonaceous substances such as coal from materials containing them, thereby producing a froth containing the coal, etc., and also the organic materials from the liquor. In some cases the effluent may be diluted with sea-water, and, in recovering carbonaceous shales, there may be added to the liquor a small proportion of paraffin oil.

Are oil and gas stocks from the Australian market riskier than coal and uranium stocks? Dependence risk analysis and portfolio optimization

International Nuclear Information System (INIS)

Arreola Hernandez, Jose

2014-01-01

This article models the dependence risk and resource allocation characteristics of two 20-stock coal–uranium and oil–gas sector portfolios from the Australian market in the context of the global financial crisis of 2008–2009. The modeling framework implemented consists of pair vine copulas and, linear and nonlinear portfolio optimization methods with respect to five risk measures. The paper's objectives are to find out if the oil and gas stocks are riskier than the coal and uranium stocks, to identify the optimization method and risk measure that produce the best risk-return trade-off, to recognize the stocks in which the optimal weight allocations converge on average, and to acknowledge the vine copula model that best accounts for the overall dependence of the energy portfolios. The research findings indicate that the oil stocks have higher dependence risk than the coal, uranium and gas stocks in financial crisis periods. The higher risk of the oil stocks is confirmed by the larger concentration of symmetric and asymmetric dependence they have in the negative tail. The canonical vine (c-vine) copula model is observed to better capture the overall dependence of the energy portfolios. The combination of a pair c-vine copula and nonlinear portfolio optimization produces the highest return relative to risk. The optimal weight allocations converge on average in some stocks. - Highlights: • Vine copula dependence modeling of coal, uranium, oil and gas stocks • Oil stocks are riskier than coal, uranium and gas stocks in financial crisis periods. • The c-vine model better captures the overall dependence of the energy portfolios. • Vine copulas and nonlinear optimization combined produce the best results. • The optimal weight allocations converge on average in some stocks

Pressure Prediction of Coal Slurry Transportation Pipeline Based on Particle Swarm Optimization Kernel Function Extreme Learning Machine

Directory of Open Access Journals (Sweden)

Xue-cun Yang

2015-01-01

Full Text Available For coal slurry pipeline blockage prediction problem, through the analysis of actual scene, it is determined that the pressure prediction from each measuring point is the premise of pipeline blockage prediction. Kernel function of support vector machine is introduced into extreme learning machine, the parameters are optimized by particle swarm algorithm, and blockage prediction method based on particle swarm optimization kernel function extreme learning machine (PSOKELM is put forward. The actual test data from HuangLing coal gangue power plant are used for simulation experiments and compared with support vector machine prediction model optimized by particle swarm algorithm (PSOSVM and kernel function extreme learning machine prediction model (KELM. The results prove that mean square error (MSE for the prediction model based on PSOKELM is 0.0038 and the correlation coefficient is 0.9955, which is superior to prediction model based on PSOSVM in speed and accuracy and superior to KELM prediction model in accuracy.

Oxidation and carbonisation of coals: a case study of coal fire affected coals from the Wuda coalfield, Inner Mongolia, China

Science.gov (United States)

Kus, Jolanta; Meyer, Uwe; Ma, Jianwei; Chen-Brauchler, Dai

2010-05-01

At the coalfield of Wuda (Inner Mongolia, PR China) extensive underground coal fires cause widespread thermal and oxidative effects in coal seams. Within phase B of the Coal Fire Research Project of the Sino-German Initiative, methods for innovative fire-extinguishing technologies were investigated in multifaceted research approaches. Extensive investigations of oxidative and thermally affected coal seams in coal fire zone 18 were conducted in 2008 prior to application of new fire-extinguishing methods. We present results from the outcrop of coal seam No. 4 in the fire zone 18. The coal of seam No. 4 is of Early Permian age and belongs stratigraphically to the Shanxi Formation. The unaffected coal displays a high volatile bituminous A rank with a background value of random vitrinite reflectance ranging from 0.90 to 0.96 % Rr. Coal channel samples were coallected at actively extracted coal faces along multiple profiles with surface temperatures ranging from about 50° to 600°C. Microscopic examinations revealed a variety of products of coal exposure to the fire. Within coal samples, a marked rise in vitrinite reflectance from background values to 5.55% Rr (6.00 % Rmax) is encountered. In addition, a number of coal samples showed suppressed vitrinite reflectances ranging between 0.82 to 0.88% Rr. Further, seemingly heat unaffected coal samples display intensive development of oxidations rims at coal grain edges and cracks as well as shrinkage cracks and formation of iron oxides/hydroxides. Instead, thermally affected coal samples with higher coalification grade are further characterised by development of macropores (devolatilisation pores) in vitrinitic streaks, transformation of liptinite to meta-liptinite and micrinite as well as by natural coke particles of mostly porous nature and fine to coarse grained anisotropic mosaic. Coal petrographic investigations confirmed a hypothesis that both, oxidations as well as low temperature carbonisation govern the thermal

Characteristic parameters of the coal briquetting process

International Nuclear Information System (INIS)

Davkova, Katica

1998-01-01

The complete knowledge about the energetic sources in our country - Republic of Macedonia, point to the fact that coals are the most attractive and highly productive, still keeping the leadership position. However, the process of lignite exploitation causes their degradation and formation of large amount of fine fractions. The industrial valorization of these fractions is the most actual problem that could be solved only through production of made-up enriched fuels of wide spectrum of application. Thus, briquetting formation, with or without use of binds, is a process of mechanical or combined modification of coal fine fractions. At the same time, this is a possible procedure of solid fuels enrichment. Lignite from the Macedonian coal deposits 'Suvodol', 'Priskupshtina' and 'Brik-Berovo' is analyzed, in order to examine the possibilities of its briquetting. The results show that the 'Suvodol' lignite satisfy the quality requirements given with the MKS B H1.031 standard as well as the 'Brik-Berovo' lignite

Investigation cost subsidizing project for improving development of overseas coals in fiscal 1999. Investigations on improving development of Asian and Pacific coals (Investigation on optimizing the coal transportation system in East Karimantan Province in Indonesia); 1999 nendo Asia Taiheiyo sekitan kaihatsu kodoka chosa. Indonesia Higashi Karimantan shu ni okeru sekitan yuso system saitekika chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Evaluation was given on coal production quantity and coal transportation capability in areas scheduled of future development in Karimantan, Indonesia. Discussions were given on an optimal coal transportation system in East Karimantan Province. The coal production quantity in East Karimantan in fiscal 1999 was 35.27 million tons, accounting for 48% of the total Indonesian coal production. Production of 81.90 million tons is anticipated in 2020. Quality of the coal being produced is low in ash and high in water content in general. Calorific power is 5800 kcal or more. Sulfur content is 0.5% or more, not necessarily a low sulfur coal. The result of analyzing the optimal transportation routes by using the LP model may be summarized as follows: such scenarios are regarded to be largely profitable and advantageous that assume making railways utilizable as the land transportation in addition to use of trucks, belt conveyers, and barges, expanding coal terminals at the ports of PBCT, KPC, BCT and NPLCT, and newly building ports at Tarakan, TgSengatta, BPCTH, and Mangkapadie. (NEDO)

Process for hydrogenating coal and coal solvents

Energy Technology Data Exchange (ETDEWEB)

Shridharani, K.G.; Tarrer, A.R.

1983-02-15

A novel process is described for the hydrogenation of coal by the hydrogenation of a solvent for the coal in which the hydrogenation of the coal solvent is conducted in the presence of a solvent hydrogenation catalyst of increased activity, wherein the hydrogenation catalyst is produced by reacting ferric oxide with hydrogen sulfide at a temperature range of 260/sup 0/ C to 315/sup 0/ C in an inert atmosphere to produce an iron sulfide hydrogenation catalyst for the solvent. Optimally, the reaction temperature is 275/sup 0/ C. Alternately, the reaction can be conducted in a hydrogen atmosphere at 350/sup 0/ C.

Marketing Canada's coal

Energy Technology Data Exchange (ETDEWEB)

1985-11-01

The topics are presented which were discussed at the 36th Canadian Coal Conference, held in Vancouver, BC in September 1985. The theme was Challenges, today and tomorrow and the conference sought to examine the primary problems confronting the world coal industry today: overcapacity, soft demand, depressed prices and intense global competition. Coal production in Canada was presented and its role in the steelmaking and electric power industries evaluated. A general mood of optimism prevailed.

Mesoporous materials as fining agents in variety Cabernet Sauvignon wines

Directory of Open Access Journals (Sweden)

Dumitriu Georgiana-Diana

2016-01-01

Full Text Available Innovative oenological products and techniques constantly need to be optimized in order to produce high quality wines that are able to fulfill the demanding consumers, with a pleasant colour, astringency, bitterness and a balanced organoleptic profile. New mesoporous materials with viability and environmental safety characteristics, might be a feasible alternative to the use of bentonite, while nowadays in the winemaking there is a major challenge caused by wastes derivate mainly from wine clarification stages. This study was aimed at investigating the influence of conventional (bentonite and activated coal and alternative (MCM-41, SBA-15, KIT-6 fining agents on enological parameters, colour, as well as on the antioxidant activity of a Cabernet Sauvignon wines. Our results show that mesoporous materials, KIT-6 and SBA-15 (6 g/L present the highest reduction on antioxidant activity with 23.08% and 24.41%, while bentonite and activated coal (1.5 g/L reduced with 20.72%, respectively 33.18%. Cluster analysis performed with the values of antioxidant activity differentiated wines treated with activated carbon from other wines.

Coal slurries: An environmental bonus?

International Nuclear Information System (INIS)

Basta, N.; Moore, S.; Ondrey, G.

1994-01-01

Developers and promoters of coal-water slurries and similar CWF (coal-water fuel) technologies have had a hard time winning converts since they unveiled their first commercial processes in the 1970s. The economic appeal of such processes, marginal at best, varies with the price of oil. Nevertheless, the technology is percolating, as geopolitics and environmental pressures drive new processes. Such fuels are becoming increasingly important to coal-rich, oil-poor nations such as China, as they attempt to build an onshore fuel supply. Meanwhile, improvements are changing the way coal-fired processes are viewed. Where air pollution regulations once discouraged the use of coal fuels, new coal processes have been developed that cut nitrous oxides (NOx) emissions and provide a use for coal fines, previously viewed as waste. The latest developments in the field were all on display at the 19th International Technical Conference on Coal Utilization and Fuel Systems, held in Clearwater, Fla., on March 21--24. At this annual meeting, sponsored by the Coal and Slurry Technology Association, (Washington, D.C.) and the Pittsburgh Energy Technology Center of the US Dept. of Energy (PETC), some 200 visitors from around the work gathered to discuss the latest developments in coal slurry utilization--new and improved processes, and onstream plants. This paper presents highlights from the conference

Use of moist run-of-mine coal for gasification

Energy Technology Data Exchange (ETDEWEB)

Sowka, K.; Duerlich, M.; Rabe, W. (VEB Gaskombinat Fritz Selbmann, Schwarze Pumpe (German Democratic Republic))

1988-01-01

A Series of experiments was performed in 1982 and 1986 to assess the feasibility of substituting brown coal briquets by raw brown coal in the fixed bed gasification plant for producing town gas at Schwarze Pumpe, GDR. Raw brown coal (50% coal moisture, screened coal of fractions 20 to 80 mm) had to be mixed with dry briquets to maintain a maximum 35% coal charge moisture. Briquet substitution degree varied from 20 to 50%. Short-term gasification tests were also carried out at an experimental generator examining 80 to 100% substitution degrees. Parameters of generator operation that were achieved are provided. Experiments proved that 50% briquet substitution is technologically feasible in industrial plant operation employing unscreened coal containing all coal fines. An economic assessment is further made that shows substantial energy savings in coal drying and briquetting.

Use of Unprocessed Coal Bottom Ash as Partial Fine Aggregate ...

African Journals Online (AJOL)

2012r

transportation applications such as structural fill, road base material, and as snow ... normal fine particles resulting in weak porous paste, modulus of elasticity is ..... with the porous structure and high absorptivity of fine particles of bottom ash.

An update on blast furnace granular coal injection

Energy Technology Data Exchange (ETDEWEB)

Hill, D.G. [Bethlehem Steel Corp., Burns Harbor, IN (United States); Strayer, T.J.; Bouman, R.W. [Bethlehem Steel Corp., PA (United States)

1997-12-31

A blast furnace coal injection system has been constructed and is being used on the furnace at the Burns Harbor Division of Bethlehem Steel. The injection system was designed to deliver both granular (coarse) and pulverized (fine) coal. Construction was completed on schedule in early 1995. Coal injection rates on the two Burns Harbor furnaces were increased throughout 1995 and was over 200 lbs/ton on C furnace in September. The injection rate on C furnace reached 270 lbs/ton by mid-1996. A comparison of high volatile and low volatile coals as injectants shows that low volatile coal replaces more coke and results in a better blast furnace operation. The replacement ratio with low volatile coal is 0.96 lbs coke per pound of coal. A major conclusion of the work to date is that granular coal injection performs very well in large blast furnaces. Future testing will include a processed sub-bituminous coal, a high ash coal and a direct comparison of granular versus pulverized coal injection.

Adaptive optimization as a design and management methodology for coal-mining enterprise in uncertain and volatile market environment - the conceptual framework

Science.gov (United States)

Mikhalchenko, V. V.; Rubanik, Yu T.

2016-10-01

The work is devoted to the problem of cost-effective adaptation of coal mines to the volatile and uncertain market conditions. Conceptually it can be achieved through alignment of the dynamic characteristics of the coal mining system and power spectrum of market demand for coal product. In practical terms, this ensures the viability and competitiveness of coal mines. Transformation of dynamic characteristics is to be done by changing the structure of production system as well as corporate, logistics and management processes. The proposed methods and algorithms of control are aimed at the development of the theoretical foundations of adaptive optimization as basic methodology for coal mine enterprise management in conditions of high variability and uncertainty of economic and natural environment. Implementation of the proposed methodology requires a revision of the basic principles of open coal mining enterprises design.

Comparison of the physical and chemical characteristics of fine road dust at different urban sites.

Science.gov (United States)

Lee, Kwang Yul; Batmunkh, Tsatsral; Joo, Hung Soo; Park, Kihong

2018-04-18

The size distribution and chemical components of a fine fraction (road dust collected at urban sites in Korea (Gwangju) and Mongolia (Ulaanbaatar) where distinct urban characteristics exist were measured. A clear bimodal size distribution was observed for the resuspended fine road dust at the urban sites in Korea. The first mode peaked at 100-110 nm, and the second peak was observed at 435-570 nm. Ultrafine mode (~30 nm) was found for the fine road dust at the Mongolia site, which was significantly affected by residential coal/biomass burning. The contribution of the water-soluble ions to the fine road dust was higher at the sites in Mongolia (15.8-16.8%) than at those in Korea (1.2-4.8%). Sulfate and chloride were the most dominant ionic species for the fine road dust in Mongolia. As (arsenic) was also much higher for the Mongolian road dust than the others. The sulfate, chloride, and As mainly come from coal burning activity, suggesting that coal and biomass combustion in Mongolia during the heating season should affect the size and chemical components of the fine road dust. Cu (copper) and Zn (zinc), carbonaceous particles (organic carbon [OC] and elemental carbon [EC]) increased at sites in Korea, suggesting that the fine road dust at these sites was significantly affected by the high volume of traffic (engine emission and brake/tire wear). Our results suggest that chemical profiles for road dust specific to certain sites should be applied to more accurately apportion road dust source contributing to the ambient particulate matter. Size and chemical characteristics of fine road dust at sites having distinct urban characteristics were examined. Residential coal and biomass burning and traffic affected physiochemical properties of the fine road dust. Different road dust profiles at different sites should be needed to determine the ambient PM2.5 sources more accurately.

Kinetic comparison of biological and conventional flotation of coal

Energy Technology Data Exchange (ETDEWEB)

Amini, E.; Oliazadeh, M.; Kolahdoozan, M. [University of Queensland, Brisbane, Qld. (Australia)

2009-03-15

Froth flotation is commonly used in coal processing to selectively recover the organic material (coal) from inorganic waste material. Tabas coal, located in east Iran, contains fine disseminated pyrite which is floated with coal during flotation, and hence decreasing the quality of the final concentrate. Reagents, such as sodium cyanide, are typically added to depress pyrite. Due to the toxicity of cyanide, alternative strategies for depressing pyrite flotation are being investigated. In this paper the metallurgical performance of Tabas coal treated with sodium cyanide is compared to that of Tabas coal which has undergone bacterial treatment using Acidithiobacillus ferrooxidans. Results indicate that bacterial treatment decreases the flotation rate of pyrite and improves the selectivity between coal and gangue. The possibility of using bacteria in place of toxic chemicals such as cyanide has significant environmental benefit.

Optimal scheduling for enhanced coal bed methane production through CO2 injection

International Nuclear Information System (INIS)

Huang, Yuping; Zheng, Qipeng P.; Fan, Neng; Aminian, Kashy

2014-01-01

Highlights: • A novel deterministic optimization model for CO 2 -ECBM production scheduling. • Maximize the total profit from both sales of natural gas and CO 2 credits trading in the carbon market. • A stochastic model incorporating uncertainties and dynamics of NG price and CO 2 credit. - Abstract: Enhanced coal bed methane production with CO 2 injection (CO 2 -ECBM) is an effective technology for accessing the natural gas embedded in the traditionally unmineable coal seams. The revenue via this production process is generated not only by the sales of coal bed methane, but also by trading CO 2 credits in the carbon market. As the technology of CO 2 -ECBM becomes mature, its commercialization opportunities are also springing up. This paper proposes applicable mathematical models for CO 2 -ECBM production and compares the impacts of their production schedules on the total profit. A novel basic deterministic model for CO 2 -ECBM production including the technical and chemical details is proposed and then a multistage stochastic programming model is formulated in order to address uncertainties of natural gas price and CO 2 credit. Both models are nonlinear programming problems, which are solved by commercial nonlinear programming software BARON via GAMS. Numerical experiments show the benefits (e.g., expected profit gain) of using stochastic models versus deterministic models

Fine particle coal as a source of energy in small-user applications

Energy Technology Data Exchange (ETDEWEB)

Mitchell, T M

1986-01-01

The potential savings are reviewed which are involved in the combustion of coal-water mixtures in atmospheric fluidized bed combustors and pulsed combustors for space and water heating in residential structures in the USA. Savings in 'present value' operating costs of heating systems which would be achieved by switching from oil to coal are presented for New England, the Middle Atlantic and East North Central sub-regions at different interest rates from 10 to 30%, and assuming low rates of growth in petroleum prices. These savings define the extra amount of money the user would be prepared to pay to purchase a coal slurry system. At a purchase price of 2500 dollars, this option would only be profitable for commercial users.

Characterization of the impregnated iron based catalyst for direct coal liquefaction by EXAFS

International Nuclear Information System (INIS)

Yang Jianli; Zhun Jisheng; Liu Zhenyu; Zhong Bing

2002-01-01

Catalyst plays an important role in direct coal liquefaction (DCL). Iron catalysts are regarded as the most attractive catalysts for DCL. To maximize catalytic effect and minimize catalysts usage, ultra-fine size catalysts are preferred. The most effective catalysts are found to be those impregnated onto coal because of their high dispersion on coal surface and intimate contact with coal particles. Besides the physical size, chemical form of a catalyst or a catalyst precursor is also important in determination of DCL activity. The expended X-ray absorption fine structure spectroscopy technique were used in this study. It was shown that the catalysts tested are in nanomater range and have structure mainly in the form of γ-FeOOH and FeS, or possibly of Fe/O/S. The presence of γ-FeOOH can be attributed to the interaction between Fe and the oxygen containing groups of coal or oxygen from moisture

A hybrid GA-TS algorithm for open vehicle routing optimization of coal mines material

Energy Technology Data Exchange (ETDEWEB)

Yu, S.W.; Ding, C.; Zhu, K.J. [China University of Geoscience, Wuhan (China)

2011-08-15

In the open vehicle routing problem (OVRP), the objective is to minimize the number of vehicles and the total distance (or time) traveled. This study primarily focuses on solving an open vehicle routing problem (OVRP) by applying a novel hybrid genetic algorithm and the Tabu search (GA-TS), which combines the GA's parallel computing and global optimization with TS's Tabu search skill and fast local search. Firstly, the proposed algorithm uses natural number coding according to the customer demands and the captivity of the vehicle for globe optimization. Secondly, individuals of population do TS local search with a certain degree of probability, namely, do the local routing optimization of all customer sites belong to one vehicle. The mechanism not only improves the ability of global optimization, but also ensures the speed of operation. The algorithm was used in Zhengzhou Coal Mine and Power Supply Co., Ltd.'s transport vehicle routing optimization.

A spatial analysis of China's coal flow

International Nuclear Information System (INIS)

Mou Dunguo; Li Zhi

2012-01-01

The characteristics of China's energy structure and the distribution of its coal resources make coal transportation a very important component of the energy system; moreover, coal transportation acts as a bottleneck for the Chinese economy. To insure the security of the coal supply, China has begun to build regional strategic coal reserves at some locations, but transportation is still the fundamental way to guaranty supply security. Here, we study China's coal transportation quantitatively with a linear programming method that analyses the direction and volume of China's coal flows with the prerequisite that each province's supply and demand balance is guaranteed. First, we analyse the optimal coal transportation for the status quo coal supply and demand given the bottleneck effects that the Daqin Railway has on China's coal flow; second, we analyse the influence of future shifts in the coal supply zone in the future, finding that China's coal flows will also change, which will pressure China to construct railways and ports; and finally, we analyse the possibility of exploiting Yangtze River capacity for coal transportation. We conclude the paper with suggestions for enhancing China's coal transportation security. - Highlights: ► We use linear programming to study China's coal transportation. ► First, analyse the optimal coal flow under the status quo condition. ► Second, analyse influences of coal supply zone shifts to Neimeng and Xinjiang. ► Third, analyse the influence of using Yangtze River for coal transportation. ► At last, we give suggestions about infrastructure construction to guaranty China's long-run coal supply security.

Technological and economic aspects of coal biodesulfurisation.

Science.gov (United States)

Klein, J

1998-01-01

The sulfur found in coal is either part of the molecular coal structure (organically bound sulfur), is contained in minerals such as pyrite (FeS2), or occurs in minor quantities in the form of sulfate and elemental sulfur. When pyrite crystals are finely distributed within the coal matrix, mechanical cleaning can only remove part of the pyrite. It can, however, be removed by microbial action requiring only mild conditions. The process involves simple equipment, almost no chemicals, but relatively long reaction times, and treatment of iron sulfate containing process water. Different process configurations are possible, depending on the coal particle size. Coal with particle sizes of less than 0.5 mm is preferably desulfurised in slurry reactors, while lump coal (> 0.5 mm) should be treated in heaps. Investment and operating costs are estimated for different process configurations on an industrial scale. Concerning the organically bound sulfur in coal there is up to now no promising biochemical pathway for the degradation and/or desulfurisation of such compounds.

Optimization principles for preparation methods and properties of fine ferrite materials

Science.gov (United States)

Borisova, N. M.; Golubenko, Z. V.; Kuz'micheva, T. G.; Ol'khovik, L. P.; Shabatin, V. P.

1992-08-01

The paper is devoted to the problems of development of fine materials based on Ba-ferrite for vertical magnetic recording in particular. Taking an analogue — BaFe 12-2 xCo xTe xO 19 — we have optimized the melt co-precipitation method and shown a new opportunity to provide chemical homogeneity of microcrystallites by means of cryotechnology. Magnetic characteristics of the magnetic tape experimental sample for digital video recording are presented. A series of principles of consistent control of ferrite powder properties are formulated and illustrated with specific developments.

A review on effluent generation in coal mines and its treatment methods

Energy Technology Data Exchange (ETDEWEB)

Sethi, R.; Karmakar, N.C.; Gupta, S. [Banaras Hindu University, Varanasi (India)

2008-07-01

The waste water of coal washeries, coal handling plants, workshops and overburden runoff of a coal mine contains a high concentration of suspended fine particles which usually remain after treatment in sedimentation tanks. The study on the performance characteristics of different coagulants shows that the turbidity removal efficiency depends much on the characteristics of the effluent and combined coagulants perform better than individuals. The various sources of generation of effluent and their treatment methods are discussed. It is suggested that the mine owners should consider the mine effluent as a rich source of both fine particles of coal and precious water. The coal particles are of high grade and may be used in coke preparation and water may be reused in mine to avoid the extra cost for water. The effluent treatment methods are required to be studied properly, so that less consumption of chemicals will be possible. If polyelectrolyte is used along with the other coagulants, the clarification performance will be improved. The best combination of chemicals are selected and practiced in mines. 14 refs., 5 tabs.

Ultrafine ash aerosols from coal combustion: Characterization and health effects

Energy Technology Data Exchange (ETDEWEB)

William P. Linak; Jong-Ik Yoo; Shirley J. Wasson; Weiyan Zhu; Jost O.L. Wendt; Frank E. Huggins; Yuanzhi Chen; Naresh Shah; Gerald P. Huffman; M. Ian Gilmour [US Environmental Protection Agency, Research Triangle Park, NC (United States). National Risk Management Research Laboratory

2007-07-01

Ultrafine coal fly-ash particles withdiameters less than 0.5 {mu}m typically comprise less than 1% of the total fly-ash mass. This paper reports research focused on both characterization and health effects of primary ultrafine coal ash aerosols alone. Ultrafine, fine, and coarse ash particles were segregated and collected from a coal burned in a 20 kW laboratory combustor and two additional coals burned in an externally heated drop tube furnace. Extracted samples from both combustors were characterized by transmission electron microscopy (TEM), wavelength dispersive X-ray fluorescence(WD-XRF) spectroscopy, Moessbauer spectroscopy, and X-ray absorption fine structure (XAFS) spectroscopy. Pulmonary inflammation was characterized by albumin concentrations in mouse lung lavage fluid after instillation of collected particles in saline solutions and a single direct inhalation exposure. Results indicate that coal ultrafine ash sometimes contains significant amounts of carbon, probably soot originating from coal tar volatiles, depending on coal type and combustion device. Surprisingly, XAFS results revealed the presence of chromium and thiophenic sulfur in the ultrafine ash particles. The instillation results suggested potential lung injury, the severity of which could be correlated with the carbon (soot) content of the ultrafines. This increased toxicity is consistent with theories in which the presence of carbon mediates transition metal (i.e., Fe) complexes, as revealed in this work by TEM and XAFS spectroscopy, promoting reactive oxygenspecies, oxidation-reduction cycling, and oxidative stress. 24 refs., 7 figs.

Lance for injecting highly-loaded coal slurries into the blast furnace

Energy Technology Data Exchange (ETDEWEB)

Illuminati, D.

1991-10-29

A lance is used to inject fuel oil into a blast furnace. This simple design permits conversion of coal water and coal tar slurries to a fine mist at very low flow rates. This design prevents the build-up of deposits which increases service life and steadies the flow rate.

Low-rank coal research: Volume 2, Advanced research and technology development: Final report

Energy Technology Data Exchange (ETDEWEB)

Mann, M.D.; Swanson, M.L.; Benson, S.A.; Radonovich, L.; Steadman, E.N.; Sweeny, P.G.; McCollor, D.P.; Kleesattel, D.; Grow, D.; Falcone, S.K.

1987-04-01

Volume II contains articles on advanced combustion phenomena, combustion inorganic transformation; coal/char reactivity; liquefaction reactivity of low-rank coals, gasification ash and slag characterization, and fine particulate emissions. These articles have been entered individually into EDB and ERA. (LTN)

Alternative reaction routes during coal hydrogenation and coal derived oil upgrading

Energy Technology Data Exchange (ETDEWEB)

Schulz, H.; Kordokuzis, G.; Langner, M. (University of Karlsruhe, Karlsruhe (Germany, F.R.). Engler-Bunte-Institute)

1989-10-01

Alternative reaction routes have been traced for the hydrodenitrogenation and hydrodeoxygenation of coal structure related model compounds. Reaction pathways are very structure specific. It is shown how reaction mechanisms switch from one route to another with changes in reaction conditions and catalyst features. Optimization of coal liquefaction processes can make use of this detailed understanding of selectivity. 5 refs., 7 figs.

Health impacts of coal: facts and fallacies

Energy Technology Data Exchange (ETDEWEB)

Finkelman, R.B. [University of Texas, Dallas, TX (United States)

2007-02-15

Coal has contributed enormously to the advance of civilization by providing an abundant, inexpensive, and convenient source of energy. Concurrent with its contributions, coal has extracted a high cost in terms of environmental damage and human health impacts. Unfortunately, the links between coal use and human health are distorted by a great deal of ignorance and misinformation. This paper discusses the facts and fallacies of the direct health impacts caused by coal. These include health problems caused by arsenic, fluorine, mercury and selenium released in coal use in the residential sector. The trace element iodine however may help prevent iodine deficiency disorder. Lignite in the ground in some Balkan areas has been associated with a urinary tract cancer known as Balkan endemic nephropathy (BEN). Uncontrolled burning coal seams and coal waste piles contribute to global warming and to respiratory problems. The 10-fold enrichment of trace elements in fly ash and the fine particles released from power plants could present a health threat but where good pollution control technology and disposal practices are applied the health threat is probably minimal. Radioactivity levels in coal are thought to be too low to cause concern. 27 refs., 2 figs.

Equations describing contamination of run of mine coal with dirt in the Upper Silesian Coalfield

Energy Technology Data Exchange (ETDEWEB)

Winiewski, J J

1977-12-01

Statistical analysis proved that contamination with dirt of run of mine coal from seams in the series 200 to 600 of the Upper Silesian Coalfield depends on the average ash content of a given raw coal. A regression equation is deduced for coarse and fine sizes of each coal. These equations can be used to predict the degree of contamination of run of mine coal to an accuracy sufficient for coal preparation purposes.

SELECTION OF SUSTAINABLE TECHNOLOGIES FOR COMBUSTION OF BOSNIAN COALS

Directory of Open Access Journals (Sweden)

Anes Kazagić

2010-01-01

Full Text Available This paper deals with optimization of coal combustion conditions to support selection a sustainable combustion technology and an optimal furnace and boiler design. A methodology for optimization of coal combustion conditions is proposed and demonstrated on the example of Bosnian coals. The properties of Bosnian coals vary widely from one coal basin to the next, even between coal mines within the same basin. Very high percentage of ash (particularly in Bosnian brown coal makes clear certain differences between Bosnian coal types and other world coal types, providing a strong argument for investigating specific problems related to the combustion of Bosnian coals, as well as ways to improve their combustion behaviour. In this work, options of the referent energy system (boiler with different process temperatures, corresponding to the different combustion technologies; pulverised fuel combustion (slag tap or dry bottom furnace and fluidized bed combustion, are under consideration for the coals tested. Sustainability assessment, based on calculation economic and environment indicators, in combination with common low cost planning method, is used for the optimization. The total costs in the lifetime are presented by General index of total costs, calculated on the base of agglomeration of basic economic indicators and the economic indicators derived from environmental indicators. So, proposed methodology is based on identification of those combustion technologies and combustion conditions for coals tested for which the total costs in lifetime of the system under consideration are lowest, provided that all environmental issues of the energy system is fulfilled during the lifetime. Inputs for calculation of the sustainability indicators are provided by the measurements on an experimental furnace with possibility of infinite variation of process temperature, supported by good praxis from the power plants which use the fuels tested and by thermal

Comprehensive report to Congress Clean Coal Technology Program

International Nuclear Information System (INIS)

1992-06-01

This project will provide a full-scale demonstration of Micronized Coal Reburn (MCR) technology for the control of NO x on a wall-fired steam generator. This demonstration is expected to reduce NO x emissions by 50 to 60%. Micronized coal is coal that has been very finely pulverized (80% less than 325 mesh). This micronized coal, which may comprise up to 30% of the total fuel fired in the furnace, is fired high in the furnace in a fuel-rich reburn zone at a stoichiometry of 0.8. Above the reburn zone, overfire air is injected into the burnout zone at high velocity for good mixing to ensure complete combustion. Overall excess air is 15%. MCR technology reduces NO x emissions with minimal furnace modifications, and the improved burning characteristics of micronized coal enhance boiler performance

Fresh Properties and Flexural Strength of Self-Compacting Concrete Integrating Coal Bottom Ash

Directory of Open Access Journals (Sweden)

Jamaluddin Norwati

2016-01-01

Full Text Available This paper presents the effect of using coal bottom ash as a partial replacement of fine aggregates in self-compacting concrete (SCC on its fresh properties and flexural strength. A comparison between SCC with various replacements of fine aggregates with coal bottom ash showed that SCC obtained flexural strength decrease on increase of water cement ratio from 0.35 to 0.45. The natural sand was replaced with coal bottom ash up to 30% volumetrically. The fresh properties were investigated by slump flow, T500 spread time, L-box test and sieve segregation resistance in order to evaluate its self-compatibility by compared to control samples embed with natural sand. The results revealed that the flowability and passing ability of SCC mixtures are decreased with higher content of coal bottom ash replacement. The results also showed that the flexural strength is affected by the presence of coal bottom ash in the concrete. In addition, the water cement ratios are influence significantly with higher binder content in concrete.

Differential pulmonary inflammation and in vitro cytotoxicity of size-fractionated fly ash particles from pulverized coal combustion

Energy Technology Data Exchange (ETDEWEB)

M. Ian Gilmour; Silvia O' Connor; Colin A.J. Dick; C. Andrew Miller; William P. Linak [U.S. Environmental Protection Agency, Research Triangle Park, NC (United States). National Health and Environmental Effects Research Laboratory

2004-03-01

Exposure to airborne particulate matter (PM) has been associated with adverse health effects in humans. Pulmonary inflammatory responses were examined in CD1 mice after intratracheal instillation of 25 or 100 {mu}g of ultrafine ({lt}0.2 {mu}m), fine ({lt}2.5 {mu}m), and coarse ({gt}2.5 {mu}m) coal fly ash from a combusted Montana subbituminous coal, and of fine and coarse fractions from a combusted western Kentucky bituminous coal. After 18 hr, the lungs were lavaged and the bronchoalveolar fluid was assessed for cellular influx, biochemical markers, and pro-inflammatory cytokines. The responses were compared with saline and endotoxin as negative and positive controls, respectively. On an equal mass basis, the ultrafine particles from combusted Montana coal induced a higher degree of neutrophil inflammation and cytokine levels than did the fine or coarse PM. The western Kentucky fine PM caused a moderate degree of inflammation and protein levels in bronchoalveolar fluid that were higher than the Montana fine PM. Coarse PM did not produce any significant effects. In vitro experiments with rat alveolar macrophages showed that of the particles tested, only the Montana ultrafine displayed significant cytotoxicity. It is concluded that fly ash toxicity is inversely related with particle size and is associated with increased sulfur and trace element content. 42 refs., 5 figs., 3 tabs.

Combustion and emissions characterization of pelletized coal fuels. Technical report, December 1, 1992--February 28, 1993

Energy Technology Data Exchange (ETDEWEB)

Rajan, S. [Southern Illinois Univ., Carbondale, IL (United States). Dept. of Mechanical Engineering and Energy Processes

1993-05-01

The aim of this project is to demonstrate that sorbent-containing coal pellets made from low grade coal or coal wastes are viable clean burning fuels, and to compare their performance with that of standard run-of-mine coal. Fuels to be investigated are: (a) carbonated pellets containing calcium hydroxide sorbent, (b) coal fines-limestone pellets with cornstarch as binder, (c) pellets made from preparation plant recovered coal containing limestone sorbent and gasification tar as binder, and (d) a standard run-of-mine Illinois seam coal. The fuels will be tested in a laboratory scale 411 diameter circulating fluidized bed combustor. Progress this quarter has centered on the development of a hydraulic press based pellet mill capable of the high compaction pressures necessary to produce the gasification tar containing pellets outlined in (c) above. Limited quantities of the pellets have been made, and the process is being fine tuned before proceeding into the production mode. Tests show that the moisture content of the coal is an important parameter that needs to be fixed within narrow limits for a given coal and binder combination to produce acceptable pellets. Combustion tests with these pellet fuels and the standard coal are scheduled for the next quarter.

Fuel briquettes from brown coals of Yakutia

Energy Technology Data Exchange (ETDEWEB)

L.A. Nikolaeva; V.G. Latyshev; O.N. Burenina [Russian Academy of Sciences, Yakutsk (Russian Federation). Institute of Oil and Gas Problems

2009-04-15

Experimental data on the development of technology for the manufacture of briquetted fuel from brown coals with the use of various petroleum binders are presented. The influence of the moisture content, the coal particle-size composition, the binder type and concentration, the compacting pressure, and heat treatment regimes on the mechanical properties of the materials was studied. The optimal compositions and optimal values of the engineering parameters for the production of graded briquetted fuel from brown coals of the Kangalassy deposit in the Republic of Sakha (Yakutia) were established.

Floatability characteristics: A case study with three typical Indian prime coking coals

Energy Technology Data Exchange (ETDEWEB)

Chakraborty, D.; Singh, A.K.; Banerjee, P.K. [Tata Steel Ltd., Jamshedpur (India). Division for Research & Development

2008-07-01

Three types of prime coking coals (coals A, B, and C) from Jharia coalfield, India, were investigated for the variations in their floatability characteristics. Among the three coals studied, coal A showed the least floatability. However, its floatability improved to some extent at higher dosages of collector and frother. Other two types of coal, i.e., coals B and C, showed almost similar flotation performance, which was much better as compared to coal A. The studies revealed that coal showed the least floatability characteristics, primarily due to the least concentration of vitrinite and liptinite content and a high percentage of inertinite and mineral matters in the coal. Also, the lower type of vitrinite (V7-V9) was present in the coal in greater proportion as compared to the other two coals and the proportion of ultra fines (-0.053mm) in coal A was higher as compared to the other two coals.

Co-combustion of peanut hull and coal blends: Artificial neural networks modeling, particle swarm optimization and Monte Carlo simulation.

Science.gov (United States)

Buyukada, Musa

2016-09-01

Co-combustion of coal and peanut hull (PH) were investigated using artificial neural networks (ANN), particle swarm optimization, and Monte Carlo simulation as a function of blend ratio, heating rate, and temperature. The best prediction was reached by ANN61 multi-layer perception model with a R(2) of 0.99994. Blend ratio of 90 to 10 (PH to coal, wt%), temperature of 305°C, and heating rate of 49°Cmin(-1) were determined as the optimum input values and yield of 87.4% was obtained under PSO optimized conditions. The validation experiments resulted in yields of 87.5%±0.2 after three replications. Monte Carlo simulations were used for the probabilistic assessments of stochastic variability and uncertainty associated with explanatory variables of co-combustion process. Copyright © 2016 Elsevier Ltd. All rights reserved.

Dressing coals, shales, and the like

Energy Technology Data Exchange (ETDEWEB)

Osawa, H

1938-12-28

A process for dressing coals, shales, and like carbonaceous substances with the use of floating and sinking phenomena caused by differences in the specific gravities of the substances to be separated in the dressing operation is characterized by the use as the dressing medium of an aqueous suspension of clay and finely ground pyrite or iron ore cinder, or finely ground easily pulverizable iron ore, such as earthy or granular limonite. The aqueous suspension has a low viscosity and a specific gravity between 1.35 and 1.70.

Pressurized oxy-coal combustion: Ideally flexible to uncertainties

International Nuclear Information System (INIS)

Zebian, Hussam; Mitsos, Alexander

2013-01-01

Simultaneous multi-variable gradient-based optimization with multi-start is performed on a 300 MWe wet-recycling pressurized oxy-coal combustion process with carbon capture and sequestration, subject to uncertainty in fuel, ambient conditions, and other input specifications. Two forms of flue gas thermal recovery are studied, a surface heat exchanger and a direct contact separation column. Optimization enables ideal flexibility in the processes: when changing the coal utilized, the performance is not compromised compared to the optimum performance of a process specifically designed for that coal. Similarly, the processes are immune to other uncertainties like ambient conditions, air flow, slurry water flow, atomizer stream flow and the oxidizer stream oxygen purity. Consequently, stochastic programming is shown to be unnecessary. Close to optimum design, the processes are also shown to be insensitive towards design variables such as the areas of the feedwater heaters. Recently proposed thermodynamic criteria are used as embedded design specifications in the optimization process, rendering it faster and more robust. - Highlights: • Proposed formulation to assess the flexibility of power generation processes facing uncertainties. • Obtained ideal flexibility of pressurized oxy-coal combustion with respect to coal type. • Performance of processes under uncertainty match performance of optimal processes for specific set of inputs. • Stochastic programming is not required and instead hierarchic optimization is utilized

Formation of fine particles in co-combustion of coal and solid recovered fuel in a pulverized coal-fired power station

DEFF Research Database (Denmark)

Wu, Hao; Pedersen, Anne Juul; Glarborg, Peter

2011-01-01

showed an ultrafine mode centered at approximately 0.1 μm. Compared with coal combustion, co-combustion of coal and SRF increased the formation of submicron particles, especially ultrafine particles below 0.2 μm. The morphology of the particles indicated that supermicron particles were primarily formed...... by the melting of minerals. The ultrafine particles were generated through nucleation and coagulation of vaporized inorganic species, while for the particles in between supermicron and ultrafine particles, condensation of vaporized species or aggregation of nucleates on the existing spherical submicron particles...... appear to be an important formation mechanism. The elemental composition of the particles from coal combustion showed that S and Ca were significantly enriched in ultrafine particles and P was also enriched considerably. However, compared with supermicron particles, the contents of Al, Si and K were...

Clean coal technology optimization model

International Nuclear Information System (INIS)

Laseke, B.A.; Hance, S.B.

1992-01-01

Title IV of the Clean Air Act Amendments (CAAA) of 1990 contains provisions for the mitigation of acid rain precipitation through reductions in the annual emission of the acid rain precursors of sulfur dioxide (SO 2 ) and nitrogen oxide (NO x ). These provisions will affect primarily existing coal-fired power-generating plants by requiring nominal reductions of 5 millon and 10 million tons of SO 2 by the years 1995 and 2000, respectively, and 2 million tons of NO x by the year 2000 relative to the 1980 and 1985-87 reference period. The 1990 CAAA Title IV provisions are extremely complex in that they establish phased regulatory milestones, unit-level emission allowances and caps, a mechanism for inter-utility trading of emission allowances, and a system of emission allowance credits based on selection of control option and timing of its implementation. The net result of Title IV of the 1990 CAAA is that approximately 147 gigawatts (GW) of generating capacity is eligible to retrofit SO 2 controls by the year 2000. A number of options are available to bring affected boilers into compliance with Title IV. Market sharewill be influenced by technology performance and costs. These characteristics can be modeled through a bottom-up technology cost and performance optimization exercise to show their impact on the technology's potential market share. Such a model exists in the form of an integrated data base-model software system. This microcomputer (PC)-based software system consists of a unit (boiler)-level data base (ACIDBASE), a cost and performance engineering model (IAPCS), and a market forecast model (ICEMAN)

Approach to reducing the effect of bone—coal power station on radiation environment

Institute of Scientific and Technical Information of China (English)

NIShi－Ying; GUPei－Long; 等

2002-01-01

The effect of two bone-coal power stations(6MWe) on environment was investigated within the scope of the dose contribution caused by various radionucildes in different ways.It is found that the best measures to reduce the effect of bone-coal power station on radiation environment include to select a fine boiler system and a comprehensive utilization of the bone-coal cinder(BCC),soot and ash in the catchers.

Approach to reducing the effect of bone-coal power station on radiation environment

Institute of Scientific and Technical Information of China (English)

无

2002-01-01

The effect of two bone-coal power stations (6 MWe) on environment wasinvestigated within the scope of the dose contribution caused by various radionucildes in different ways. It is found that the best measures to reduce the effect of bone-coal power station on radiation environment include to select a fine boiler system and a comprehensive utilization of the bone-coal cinder (BCC), soot and ash in the catchers.

System principles and evaluation criteria of reliability for optimization of technological parameters of coal deposits

Directory of Open Access Journals (Sweden)

A.О. Khorolskiy

2017-12-01

Full Text Available The article deals with solving the scientific problem of select mining equipment for selection longwall faces of mining venture. The main goal of the paper is to study technology of coal extraction of mining venture. The paper proposes a new approach to solve a problem of mining equipment selection for longwall faces of mining venture. The article describes new method for selection of mining equipment based on theory graph. Special attention is given to technological aspects; they are lenght of longwall faces, depth of coal stratum. Predictions obtained for daily production of mining equipment are compared with design outputs. Conclusions regarding the main reason of instability of longwall faces workings are made. It is found that to be able to use standard algorithms find the shortest path between vertices, you must perform matrix description of the constructed graphs that illustrate the structure of the interaction of different types of control equipment. Using classical optimization of method of discrete mathematics and algorithms for finding the shortest path between two vertices of network models obtained from the formalization of graphs with maximum results of specific types of equipment production chains, solved the problem of rational choice cleaning equipment for the new site with the cost parameters of the mining equipment and cost of mining coal. The authors developed effective and appropriate variants for the mine development for different coal deposits of mining venture.

Anatomy of an intruded coal, I: Effect of contact metamorphism on whole-coal geochemistry, Springfield (No. 5) (Pennsylvanian) coal, Illinois Basin

Energy Technology Data Exchange (ETDEWEB)

Rimmer, Susan M. [Department of Geology, Southern Illinois University Carbondale, Carbondale, IL 62901 (United States); Yoksoulian, Lois E. [Department of Earth and Environmental Sciences, University of Kentucky, Lexington, KY 40506 (United States); Hower, James C. [Center for Applied Energy Research, University of Kentucky, 2540 Research Park Drive, Lexington, KY 40511 (United States)

2009-08-01

If time and heating rate are important agents in coal maturation, one might expect to see differences in chemical changes in response to maturation depending on the means of increased rank. Using a suite of samples obtained from an intruded Pennsylvanian-age coal in southern Illinois, we present whole-coal chemical data. Comparing these data to extant geochemical data for coals that have undergone normal burial maturation, we evaluated the hypothesis that if coal alteration occurs rapidly (due to intrusion) rather than gradually (burial maturation), then different relationships are seen in chemical composition (proximate and ultimate analyses) and vitrinite reflectance. The Pennsylvanian-age (Asturian [Westphalian D]) Springfield (No. 5) coal is mined at the Big Ridge Mine, near Eldorado, southern Illinois. This high volatile B bituminous coal was intruded by an ultramafic igneous intrusion during the early Permian. Alteration occurs out to {proportional_to} 1.2 x dike thickness and includes an increase in random vitrinite reflectance (R{sub m}) from levels {proportional_to} 0.7% to over 5.3%, loss of liptinites, and formation of devolatilization vacuoles and fine mosaic texture. Decreases in volatile matter (VM) and increases in fixed carbon (FC) appear to be less than would be expected for the level of reflectance seen within the alteration halo. Carbonate minerals have a major influence on proximate analyses but even following the removal of carbonates, the decrease in VM is still less than would be seen in coals of similar vitrinite reflectance that were altered by normal burial maturation. Carbonate mineralization also contributes to variability in ultimate analysis values approaching the intrusion, particularly for %C and %O. After carbonate removal, data for these coals do not appear to follow the normal burial coalification tracks when plotted on a van Krevelen diagram and on a Seyler chart. These differences suggest that a slightly different maturation

Improved coal grinding and fuel flow control in thermal power plants

DEFF Research Database (Denmark)

Niemczyk, Piotr; Bendtsen, Jan Dimon

2011-01-01

A novel controller for coal circulation and pulverized coal flow in a coal mill is proposed. The design is based on optimal control theory for bilinear systems with additional integral action. The states are estimated from the grinding power consumption and the amount of coal accumulated in the m......A novel controller for coal circulation and pulverized coal flow in a coal mill is proposed. The design is based on optimal control theory for bilinear systems with additional integral action. The states are estimated from the grinding power consumption and the amount of coal accumulated...... as well as when parameter uncertainties and noise are present. The proposed controller lowers the grinding power consumption while in most cases exhibiting superior performance in comparison with the PID controller....

Mechanical Properties of High Strength Concrete Containing Coal Bottom Ash and Oil-Palm Boiler Clinker as Fine Aggregates

Directory of Open Access Journals (Sweden)

Soofinajafi Mahmood

2016-01-01

Full Text Available This research aims to utilize Coal Furnace Bottom ash (CBA and Oil-Palm Boiler Clinker (OPBC as fine aggregate in concrete mix proportions. They are solid wastes from power plant and Oil Palm industry, respectively. Since these by-products do not have any primary use and are pure waste, an opportunity to use them as aggregate in concrete industry not only is economical but also will be an environmental friendly opportunity leading towards a more sustainable production chain. CBA and OPBC sands had similar grading to normal sand but have lower density and higher water absorption. In a high strength concrete, normal sand was replaced up to 25% with either CBA or OPBC. Test results showed that although water absorption of these wastes was more than normal sand but the slump value of concrete containing each of these wastes showed that these concretes had good workability. All mixes containing these wastes had slightly lower compressive strength at early ages and equivalent or higher compressive strength at later ages compared to control mix. The 28-day compressive strength of these concretes was in the range of 69–76 MPa which can be categorized as high strength concrete. In general, the performance of OPBC was better than CBA at 25% replacement level. However, it is recommended that at least 12.5% of total volume of fine aggregate in a high strength concrete is used of CBA or OPBC.

Basic studies on coal liquefaction reaction, reforming and utilization of liquefaction products

Energy Technology Data Exchange (ETDEWEB)

Shiraishi, M. (National Institute for Resources and Environment, Tsukuba (Japan))

1993-09-01

This report describes the achievement of research and development of coal liquefaction technologies in the Sunshine Project for FY 1992, regarding the coal liquefaction reaction, reforming and utilization of liquefaction products. For the fundamental study on coal liquefaction reaction, were investigated effect of asphaltene in petroleum residue on coprocessing, pretreatment effect in coprocessing of Taiheiyo coal and tarsand bitumen using oil soluble catalyst, solubilization and liquefaction of Taiheiyo coal at mild conditions with the aid of super acid, and flash hydropyrolysis of finely pulverized swollen coal under high hydrogen pressure. On the other hand, for the study on hydrotreatment of coal derived liquid, were investigated catalytic hydroprocessing of Wandoan coal liquids, production of gasoline from coal liquids by fluid catalytic cracking, solvent extraction of phenolic compounds from coal liquids, and separation of hetero compounds in coal liquid by means of high pressure crystallization. Further progress in these studies has been confirmed. 9 figs., 6 tabs.

Principles of integrated modeling of coal seam mining

Energy Technology Data Exchange (ETDEWEB)

Magda, R

1983-01-01

Mathematical modeling of underground coal mining is discussed. Construction of a mathematical model of an underground mine is analyzed. The model is based on integrating the elementary units (modules). A so-called elementary mining field is defined with the example of a longwall face. A model of an elementary coal seam zone is constructed by integrating the elementary mining fields (in time and space) and supplementing them with a suitable model of mine roadway structure. By integrating the elementary coal seam zones a model of mining level is constructed. Such a mathematical model is used for optimizing the selected mining parameters e.g. structure of mine roadways, size of a coal mine, and organizational scheme of underground mining in a mine or in a mine section using the standardized optimization criterion e.g. investment. Use of the integration model of underground mining for optimizing coal mine construction is evaluated. The following elements of investment and operating cost are considered: shaft excavation, shaft equipment, investment in mining sections, ventilation, mine draining etc. 1 reference.

Fiscal 1997 for the upgrading of the Asia/Pacific coal development. Survey of the optimization of the coal transportation system in Indonesia; 1997 nendo Asia Taiheiyo sekitan kaihatsu kodoka chosa. Indonesia ni okeru sekitan yuso system saitekika chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper summarized the results of Phase 1 and Phase 2 surveys conducted based on `Agreement on the comprehensive survey of a coal transportation system in South Sumatra` concluded between NEDO and the Ministry of Mine and Energy in Indonesia. In addition to the data collection and site surveys made in Phase 1, conducted in Phase 2 were determination of sites for harbors, determination of a scenario on coal transportation from coal mines to harbors, optimization of the coal transportation system, social/economic assessment, and proposal on the optimum transportation system. The results of the simulation were as follows: It is the most advantageous to transport coal from coal deposit area to harbor by rail and from harbor to Paiton by barge weighed over 10,000 tons. Tanjung Api Api is the most advantageous as harbor. The production scale which is profitable became more than 15 million tons. The present coal price of PTBA is $25/t arriving Suralaya. The coal in this case is said to be 5500kcal/kg in quality, and the coal of the same quality to this is only profitable. 8 refs., 68 figs., 104 tabs.

Coal combustion aerothermochemistry research. Final report

Energy Technology Data Exchange (ETDEWEB)

Witte, A.B.; Gat, N.; Denison, M.R.; Cohen, L.M.

1980-12-15

On the basis of extensive aerothermochemistry analyses, laboratory investigations, and combustor tests, significant headway has been made toward improving the understanding of combustion phenomena and scaling of high swirl pulverized coal combustors. A special attempt has been made to address the gap between scientific data available on combustion and hardware design and scaling needs. Both experimental and theoretical investigations were conducted to improve the predictive capability of combustor scaling laws. The scaling laws derived apply to volume and wall burning of pulverized coal in a slagging high-swirl combustor. They incorporate the findings of this investigation as follows: laser pyrolysis of coal at 10/sup 6/ K/sec and 2500K; effect of coal particle shape on aerodynamic drag and combustion; effect of swirl on heat transfer; coal burnout and slag capture for 20 MW/sub T/ combustor tests for fine and coarse coals; burning particle trajectories and slag capture; particle size and aerodynamic size; volatilization extent and burnout fraction; and preheat level. As a result of this work, the following has been gained: an increased understanding of basic burning mechanisms in high-swirl combustors and an improved model for predicting combustor performance which is intended to impact hardware design and scaling in the near term.

Study on dynamic multi-objective approach considering coal and water conflict in large scale coal group

Science.gov (United States)

Feng, Qing; Lu, Li

2018-01-01

In the process of coal mining, destruction and pollution of groundwater in has reached an imminent time, and groundwater is not only related to the ecological environment, but also affect the health of human life. Similarly, coal and water conflict is still one of the world's problems in large scale coal mining regions. Based on this, this paper presents a dynamic multi-objective optimization model to deal with the conflict of the coal and water in the coal group with multiple subordinate collieries and arrive at a comprehensive arrangement to achieve environmentally friendly coal mining strategy. Through calculation, this paper draws the output of each subordinate coal mine. And on this basis, we continue to adjust the environmental protection parameters to compare the coal production at different collieries at different stages under different attitude of the government. At last, the paper conclude that, in either case, it is the first arrangement to give priority to the production of low-drainage, high-yield coal mines.

Reactivity of mechanical activated coals for special utilization

Energy Technology Data Exchange (ETDEWEB)

Turcaniova, L.; Kadarova, J.; Imrich, P.; Liptaj, T.; Vidlar, J.; Vasek, J.; Foldyna, F.; Sitek, J.; Balaz, P. [Slovak Academy of Science, Kosice (Slovakia). Inst. of Geotechnology

2004-09-01

The paper presents the coal activation effect as disintegration in the nano-submicron range and destruction carbon structure. The Slovak brown coal activated in planetary mill is characterised by destruction of organic structure of coal. The biggest activation effect connected with the destruction of C-C bonds of sp{sup 3} carbons has been confirmed by {sup 13}C NMR spectroscopy in the chemical structure of humic acids extracted from the coal sample activated for a period of 60 min. The specific surface of humic acids is much smaller then that of mechanically activated sample from which they were extracted. The black Czech coal was activated by two stage disintegration. In the first stage of mechanochemical activation using Grinding Aqueous Caustic Leaching, GACL method, a fine dispersed semiproduct is formed with the size of particles from 2.5 to 9000 nm. The additional disintegration using water jet increases the effect of disintegration in the submicron area of the coal product. The volume distribution maximum achieves in this stage about 60 wt% of 750 nm grains.

Physical and chemical characterization of 50 pulverized coal ashes with respect to partial cement replacement in concrete

Energy Technology Data Exchange (ETDEWEB)

Van der Sloot, H A; Weijers, E G

1986-04-01

Physical and chemical characterization of 50 pulverized coal ashes from Dutch, Belgian and German installations has been carried out to identify the parameters that have to be kept under control, when pulverized coal ashes are to be used as partial cement replacement in concrete. For a good workability of fly ash/cement mortars the particle size and the carbon content are important. By performing a mortar flow test (Heagermann) upon delivery exterme ashes can be easily eliminated. The compressive strength is largely determined by the fineness of the ash (weight fraction below 20 micron). A direct effect of carbon content on strength development is not observed, but a reduction in mortar slow due to carbon leads to loss in strength, while the workability has to be adjusted. Size distribution measurement by optical methods is recommended as the relevant part of the ash size distribution cannot be properly assessed by sieve methods. The net contribution of fly ash to the compressive strength of a fly ash/cement (20/80) mortar exhibits a minimum at 14 days curing, which is common to all 50 ashes studied. Improvements in ash quality as obtained from pulverized-coal fired installations can be achieved by improvements in coal milling and optimizing ash collection. 6 figs., 4 tabs., 19 refs.

Structural comparison of hazardous and non-hazardous coals based on gas sorption experiments

Energy Technology Data Exchange (ETDEWEB)

Lakatos, J.; Toth, J. [Research Lab. for Mining Chemistry, Hungarian Academy of Sciences, Miskolc-Egyetemvaros (Hungary); Radnai-Gyoengyoes, Z. [Geopard Ltd., Pecs (Hungary); Bokanyi, L. [Miskolc Univ., Miskolc-Egyetemvaros (Hungary). Dept. of Process Engineering

1997-12-31

Comparison of carbon-dioxide and propane sorption at ambient temperature was used for characterising the difference of the structure of hazardous and non hazardous coals. However, hazardous coals were found more microporous or contain more closed pores than non hazardous ones, this difference couldn`t have been enlarged and attributed to one petrographic component by producing the density fractions. Gas sorption isobars (nitrogen, methane, ethane) are proposed to make a distinction between fine pore structure of coals. (orig.)

Coal sector model: Source data on coal for the energy and power evaluation program (ENPEP)

International Nuclear Information System (INIS)

Suwala, W.

1997-01-01

Coal is the major primary energy source in Poland and this circumstances requires that the data on coal supply for use in energy planning models should be prepared properly. Economic sectors' development depends on many factors which are usually considered in energy planning models. Thus, data on the development of such sectors as coal mining should be consistent with the economic assumptions made in the energy planning model. Otherwise, coal data could bias the results of the energy planning model. The coal mining and coal distribution models which have been developed at the Polish Academy of Sciences could provide proper coal data of use in ENPEP and other energy planning models. The coal mining model optimizes the most important decisions related to coal productions, such as coal mines development, retirement of non-profitable mines, and construction of new mines. The model uses basic data forecasts of coal mine costs and coal production. Other factors such as demand for coal, world coal prices, etc., are parameters which constitute constraints and requirements for the coal mining development. The output of the model is the amount of coal produced and supply curves for different coal types. Such data are necessary for the coal distribution model and could also be used by ENPEP. This paper describes the model, its structure and how the results of the model could serve as coal-related data for ENPEP. Improvement of some input data forms of the BALANCE module of ENPEP are also suggested in order to facilitate data preparation. (author). 7 figs

Coal sector model: Source data on coal for the energy and power evaluation program (ENPEP)

Energy Technology Data Exchange (ETDEWEB)

Suwala, W [Mineral and Energy Economy Research Centre, Polish Academy of Sciences, Cracow (Poland)

1997-09-01

Coal is the major primary energy source in Poland and this circumstances requires that the data on coal supply for use in energy planning models should be prepared properly. Economic sectors` development depends on many factors which are usually considered in energy planning models. Thus, data on the development of such sectors as coal mining should be consistent with the economic assumptions made in the energy planning model. Otherwise, coal data could bias the results of the energy planning model. The coal mining and coal distribution models which have been developed at the Polish Academy of Sciences could provide proper coal data of use in ENPEP and other energy planning models. The coal mining model optimizes the most important decisions related to coal productions, such as coal mines development, retirement of non-profitable mines, and construction of new mines. The model uses basic data forecasts of coal mine costs and coal production. Other factors such as demand for coal, world coal prices, etc., are parameters which constitute constraints and requirements for the coal mining development. The output of the model is the amount of coal produced and supply curves for different coal types. Such data are necessary for the coal distribution model and could also be used by ENPEP. This paper describes the model, its structure and how the results of the model could serve as coal-related data for ENPEP. Improvement of some input data forms of the BALANCE module of ENPEP are also suggested in order to facilitate data preparation. (author). 7 figs.

Mode of occurrence of arsenic in four US coals

Science.gov (United States)

Kolker, A.; Huggins, Frank E.; Palmer, C.A.; Shah, N.; Crowley, S.S.; Huffman, G.P.; Finkelman, R.B.

2000-01-01

An integrated analytical approach has been used to determine the mode of occurrence of arsenic in samples of four widely used US coals: the Pittsburgh, Illinois #6, Elkhorn/Hazard, and Wyodak. Results from selective leaching, X-ray absorption fine structure (XAFS) spectroscopy, and electron microprobe analysis show that pyrite is the principal source of arsenic in the three bituminous coals, but the concentration of As in pyrite varies widely. The Wyodak sample contains very little pyrite; its arsenic appears to be primarily associated with organics, as As3+, or as arsenate. Significant (10-40%) fractions of arsenate, derived from pyrite oxidation, are also present in the three bituminous coal samples. This information is essential in developing predictive models for arsenic behavior during coal combustion and in other environmental settings.

Effect of phosphorous transformation on the reduction of PM{sub 10} formation during Co-combustion of coal and sewage sludge

Energy Technology Data Exchange (ETDEWEB)

Zhuo, J.K.; Dong, M.; Li, G.D.; Li, S.Q.; Song, Q.; Yao, Q. [Tsinghua Univ., Beijing (China). Key Lab. of Thermal Science and Power Engineering; Duan, L. [Tsinghua Univ., Beijing (China). Dept. of Environmental Science and Engineering

2013-07-01

Co-combustion of Municipal Sewage Sludge with coal will become increasingly widely used, regarded as an important incineration method with the high thermal efficiency, low emissions, low investment and operating costs. However, the presence of phosphorus in fine particle has gained increased attention due to its environmental adverse affection and deactivation of SCR DeNOx catalysts. Therefore, the behavior of phosphorus in fine particles during co-combustion of coal and sewage sludge was investigated in a 25 kW quasi one-dimensional down-fired pulverized coal combustor, where PM{sub 10} was collected from the furnace centerline in the outlet of flue gas cooler by using a two-stage nitrogen-aspirated, water-cooling isokinetic sampling probe followed a 13-stage electric low pressure impactor. Then the formation mechanism of PM{sub 10} was investigated by observing the different fractions of sewage sludge in the coal. Similar to the coal combustion, the particle-size-distributions (PSD) of PM{sub 10} mass concentration by co-combustion of sewage sludge with coal exhibit two distinct modes separated by a fraction of 0.157-0.263 {mu}m, ultrafine mode and intermediate mode. With the sewage sludge blended sludge up to 15% (thermal ratio), the mass concentration of the total fly ash and PM{sub 10+} (Dp > 10 {mu}m) vastly increased from 1,088 and 547 mg/Nm{sup 3} (during coal combustion) to 5,059 and 4,403 mg/Nm{sup 3}. However, the mass concentration of fine particulates, such as PM{sub 1}, PM{sub 2.5} and PM{sub 10} was maintained at the emission level of coal combustion. When the fraction of sewage sludge less than 15%, the mass concentration of fine particle is higher than the emission during coal combustion, while the growth rate is only by the 3.6, 7.9 and 4.8% of the total concentration of fly ash (5% thermal). The change of the PSD of mass concentration during co- combustion of sewage sludge and coal, mainly was caused by the interaction between Si, Al and Ca, Fe

Identification of nanominerals and nanoparticles in burning coal waste piles from Portugal

Energy Technology Data Exchange (ETDEWEB)

Ribeiro, Joana [Centro de Geologia, Universidade do Porto, Rua do Campo Alegre, 687, 4169-007 Porto (Portugal); Flores, Deolinda [Centro de Geologia, Universidade do Porto, Rua do Campo Alegre, 687, 4169-007 Porto (Portugal); Departamento de Geociencias, Ambiente e Ordenamento do Territorio, Faculdade de Ciencias, Universidade do Porto, Rua do Campo Alegre, 687, 4169-007 Porto (Portugal); Ward, Colin R. [School of Biological, Earth and Environmental Sciences, University of New South Wales, Sydney, NSW 2052 (Australia); Silva, Luis F.O., E-mail: felipeqma@yahoo.com.br [Catarinense Institute of Environmental Research and Human Development, IPADHC, Capivari de Baixo, Santa Catarina (Brazil)

2010-11-01

A range of carbon nanoparticles, agglomerates and mineral phases have been identified in burning coal waste pile materials from the Douro Coalfield of Portugal, as a basis for identifying their potential environmental and human health impacts. The fragile nature and fine particle size of these materials required novel characterization methods, including energy-dispersive X-ray spectrometry (EDS), field-emission scanning electron microscope (FE-SEM), and high-resolution transmission electron microscopy (HR-TEM) techniques. The chemical composition and possible correlations with morphology of the nanominerals and associated ultra-fine particles have been evaluated in the context of human health exposure, as well as in relation to management of such components in coal-fire environments.

Durable zinc ferrite sorbent pellets for hot coal gas desulfurization

Science.gov (United States)

Jha, Mahesh C.; Blandon, Antonio E.; Hepworth, Malcolm T.

1988-01-01

Durable, porous sulfur sorbents useful in removing hydrogen sulfide from hot coal gas are prepared by water pelletizing a mixture of fine zinc oxide and fine iron oxide with inorganic and organic binders and small amounts of activators such as sodium carbonate and molybdenite; the pellets are dried and then indurated at a high temperature, e.g., 1800.degree. C., for a time sufficient to produce crush-resistant pellets.

Energy characteristics of finest coal particles surfaces versus their upgrading using flotation

Energy Technology Data Exchange (ETDEWEB)

Jerzy Sablik

2007-07-01

The paper presents selected results of investigations on energy properties of the fine coal particles, and methodological grounds for conducting such investigations. Using the discussed relationships, values of contact angle of coal particles with various degree of coalification in the range defined by the energy nonhomogeneity of the surfaces were computed. There have been determined the values of the contact angles of coal particles with hydrophobic and hydrophilic surfaces after coating with nonpolar and polar reagents. The energy state of the surfaces of coal particles in the feeds and products of industrial flotation were determined, which enabled to evaluate this process. 22 refs., 6 figs., 4 tabs.

Optimization of Fe2+ Removal from Coal Mine Wastewater using Activated Biochar of Colocasia esculenta.

Science.gov (United States)

Banerjee, Soumya; LaminKa-Ot, Augustine; Joshi, S R; Mandal, Tamal; Halder, Gopinath

2017-09-01

  The present study investigates the sorptive removal of Fe2+ from simulated coal mine waste water using steam activated biochar (SABC) developed from the roots of Colocasia esculenta. The process was optimized by response surface methodology (RSM) under the influence of pH, temperature, adsorbent dosage and contact time at a constant shaking speed of 180 rpm with an initial concentration of 3 mg/L. The uptake performance of the biosorbent was assessed following a 24 full factorial experimental matrix developed by central composite design approach. Adsorbent was characterised by SEM, EDAX, XRD and B.E.T surface area analyzer. Maximum removal of 72.96% of Fe2+ was observed at pH 7.75, temperature 37.5 °C, adsorbent dosage 1.5 g/L for a time period of 180 mins. The study suggested that SABC prepared from roots of Colocasia esculenta could be used as an efficient and cost effective sorbent for removal of Fe2+ from coal mine wastewater.

Development of Real-Time Coal Monitoring Instrument

Energy Technology Data Exchange (ETDEWEB)

Rajan Gurjar, Ph.D.

2010-06-17

Relying on coal for energy requires optimizing the extraction of heat content from various blends of coal fuel and reducing harmful constituents and byproducts. Having a real-time measurement instrument provides relevant information about toxic constituents released in the atmosphere from burning coal and optimizes the performance of a power plant. A few commercial instruments exist and have been in operation for more than a decade. However, most of these instruments are based on radioactive sources and are bulky, expensive and time-consuming. The proposed instrument is based on the Laser Induced Breakdown Spectroscopy (LIBS). The advantage of LIBS is that it is a standoff instrument, does not require sample preparation and provides precise information about sample constituents.

Further Investigations on Simultaneous Ultrasonic Coal Flotation

Directory of Open Access Journals (Sweden)

Safak Gokhan Ozkan

2017-09-01

Full Text Available This study investigates the flotation performance of a representative hard coal slime sample (d80 particle size of minus 0.2 mm obtained from the Prosper-Haniel coal preparation plant located in Bottrop, Germany. Flotation was carried out with a newly designed flotation cell refurbished from an old ultrasonic cleaning bath (2.5 L volume equipped with a single frequency (35 kHz and two different power levels (80–160 W and a sub-aeration-type flotation machine operating at a stable impeller speed (1200 rpm and air rate (2.5 L/min. The reagent combination for conventional and simultaneous ultrasonic coal flotation tests was Ekofol-440 at variable dosages (40–300 g/t with controlling water temperature (20–25 °C at natural pH (6.5–7.0. The batch coal flotation results were analyzed by comparing the combustible recovery (% and separation efficiency (% values, taking mass yield and ash concentrations of the froths and tailings into account. It was found that simultaneous ultrasonic coal flotation increased yield and recovery values of the floated products with lower ash values than the conventional flotation despite using similar reagent dosages. Furthermore, particle size distribution of the ultrasonically treated and untreated coals was measured. Finely distributed coal particles seemed to be agglomerated during the ultrasonic treatment, while ash-forming slimes were removed by hydrodynamic cavitation.

Production of fine coke in a hearth-type furnace (Report on ECSC contract 7720-EB/108)

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

A balance was established for the hearth-type coking oven and waste heat boiler system. Tests concerning the operational safety showed that, in the case of breakdowns, the oven and waste heat boiler could be shut down without any danger. The quality of the brown coal fine coke produced, could be improved by optimizing the heights of the layer in the hearth-type, the degasification temperature of the oven, and the operation of the coke cooling system. Higher coking temperature caused a lower grain disintegration and lower abrasion rates. The range of size of coke production was enlarged to lump size by additional feeding of 2-inch briquettes to the coking oven.

Low NOx combustion and SCR flow field optimization in a low volatile coal fired boiler.

Science.gov (United States)

Liu, Xing; Tan, Houzhang; Wang, Yibin; Yang, Fuxin; Mikulčić, Hrvoje; Vujanović, Milan; Duić, Neven

2018-08-15

Low NO x burner redesign and deep air staging have been carried out to optimize the poor ignition and reduce the NO x emissions in a low volatile coal fired 330 MW e boiler. Residual swirling flow in the tangentially-fired furnace caused flue gas velocity deviations at furnace exit, leading to flow field unevenness in the SCR (selective catalytic reduction) system and poor denitrification efficiency. Numerical simulations on the velocity field in the SCR system were carried out to determine the optimal flow deflector arrangement to improve flow field uniformity of SCR system. Full-scale experiment was performed to investigate the effect of low NO x combustion and SCR flow field optimization. Compared with the results before the optimization, the NO x emissions at furnace exit decreased from 550 to 650 mg/Nm³ to 330-430 mg/Nm³. The sample standard deviation of the NO x emissions at the outlet section of SCR decreased from 34.8 mg/Nm³ to 7.8 mg/Nm³. The consumption of liquid ammonia reduced from 150 to 200 kg/h to 100-150 kg/h after optimization. Copyright © 2018. Published by Elsevier Ltd.

Advanced Fine Particulate Characterization Methods

Energy Technology Data Exchange (ETDEWEB)

Steven Benson; Lingbu Kong; Alexander Azenkeng; Jason Laumb; Robert Jensen; Edwin Olson; Jill MacKenzie; A.M. Rokanuzzaman

2007-01-31

The characterization and control of emissions from combustion sources are of significant importance in improving local and regional air quality. Such emissions include fine particulate matter, organic carbon compounds, and NO{sub x} and SO{sub 2} gases, along with mercury and other toxic metals. This project involved four activities including Further Development of Analytical Techniques for PM{sub 10} and PM{sub 2.5} Characterization and Source Apportionment and Management, Organic Carbonaceous Particulate and Metal Speciation for Source Apportionment Studies, Quantum Modeling, and High-Potassium Carbon Production with Biomass-Coal Blending. The key accomplishments included the development of improved automated methods to characterize the inorganic and organic components particulate matter. The methods involved the use of scanning electron microscopy and x-ray microanalysis for the inorganic fraction and a combination of extractive methods combined with near-edge x-ray absorption fine structure to characterize the organic fraction. These methods have direction application for source apportionment studies of PM because they provide detailed inorganic analysis along with total organic and elemental carbon (OC/EC) quantification. Quantum modeling using density functional theory (DFT) calculations was used to further elucidate a recently developed mechanistic model for mercury speciation in coal combustion systems and interactions on activated carbon. Reaction energies, enthalpies, free energies and binding energies of Hg species to the prototype molecules were derived from the data obtained in these calculations. Bimolecular rate constants for the various elementary steps in the mechanism have been estimated using the hard-sphere collision theory approximation, and the results seem to indicate that extremely fast kinetics could be involved in these surface reactions. Activated carbon was produced from a blend of lignite coal from the Center Mine in North Dakota and

Physical and Chemical Properties of Coal Bottom Ash (CBA) from Tanjung Bin Power Plant

Science.gov (United States)

Izzati Raihan Ramzi, Nurul; Shahidan, Shahiron; Zulkhairi Maarof, Mohamad; Ali, Noorwirdawati

2016-11-01

The objective of this study is to determine the physical and chemical characteristics of Coal Bottom Ash (CBA) obtained from Tanjung Bin Power Plant Station and compare them with the characteristics of natural river sand (as a replacement of fine aggregates). Bottom ash is the by-product of coal combustion during the electricity generating process. However, excess bottom ash production due to the high production of electricity in Malaysia has caused several environmental problems. Therefore, several tests have been conducted in order to determine the physical and chemical properties of bottom ash such as specific gravity, density, particle size distribution, Scanning Electron Microscopic (SEM) and X- Ray Fluorescence (XRF) in the attempt to produce sustainable material from waste. The results indicated that the natural fine aggregate and coal bottom ash have very different physical and chemical properties. Bottom ash was classified as Class C ash. The porous structure, angular and rough texture of bottom ash affected its specific gravity and particle density. From the tests, it was found that bottom ash is recommended to be used in concrete as a replacement for fine aggregates.

Association of fine particulate matter from different sources with daily mortality in six US cities

Energy Technology Data Exchange (ETDEWEB)

Laden, F.; Neas, L.M.; Dockery, D.W.; Schwartz, J. [Harvard University, Boston, MA (USA). School of Medicine, Brigham & Womens Hospital

2000-07-01

In this study, the authors use the elemental composition of size-fractionated particles to identify several distinct source-related fractions of fine particles and examined the association of these fractions with daily mortality in each of six US cities. Using specific rotation factor analysis for each city, a silicon factor classified as soil and crustal material, a lead factor classified as motor vehicle exhaust, a selenium factor representing coal combustion, and up to two additional factors were identified. Daily counts of deaths from National Center for Health Statistics records were extracted and city-specific associations of mortality with each source factor were estimated. Combined effect estimates were calculated as the inverse variance weighted mean of the city-specific estimates. Results indicated that combustion particles in the fine fraction from mobile and coal combustion sources, but not fine crustal particles, are associated with increased mortality.

Application of Coal Ash to Postmine Land for Prevention of Soil Erosion in Coal Mine in Indonesia: Utilization of Fly Ash and Bottom Ash

Directory of Open Access Journals (Sweden)

Shinji Matsumoto

2016-01-01

Full Text Available The increase in the number of coal-fired power plants with the increase in coal production and its consumption has caused the problem of the treatment of a large amount of coal ash in Indonesia. In the past studies, coal ash was applied to postmine land with the aim of improving soil conditions for plant growth; however, heavy rain in the tropical climate may cause soil erosion with the change in soil conditions. This study presents the effects of application of coal ash to postmine land on soil erosion by performing the artificial rainfall test as well as physical testing. The results indicate that the risk of soil erosion can be reduced significantly by applying the coal ash which consists of more than 85% of sand to topsoil in the postmine land at the mixing ratio of over 30%. Additionally, they reveal that not only fine fractions but also microporous structures in coal ash enhance water retention capacity by retaining water in the structure, leading to the prevention of soil erosion. Thus, the risk of soil erosion can be reduced by applying coal ash to topsoil in consideration of soil composition and microporous structure of coal ash.

Mode of occurrence of chromium in four US coals

Science.gov (United States)

Huggins, Frank E.; Shah, N.; Huffman, G.P.; Kolker, A.; Crowley, S.; Palmer, C.A.; Finkelman, R.B.

2000-01-01

The mode of occurrence of chromium in three US bituminous coals and one US subbituminous has been examined using both X-ray absorption fine structure (XAFS) spectroscopy and a selective leaching protocol supplemented by scanning electron microscopy (SEM) and electron microprobe measurements. A synthesis of results from both methods indicates that chromium occurs principally in two forms in the bituminous coals: the major occurrence of chromium is associated with the macerals and is not readily leached by any reagent, whereas a second, lesser occurrence, which is leachable in hydrofluoric acid (HF), is associated with the clay mineral, illite. The former occurrence is believed to be a small particle oxyhydroxide phase (CrO(OH)). One coal also contained a small fraction (<5%) of the chromium in the form of a chromian magnetite, and the leaching protocol indicated the possibility of a similar small fraction of chromium in sulfide form in all three coals. There was little agreement between the two techniques on the mode of occurrence of chromium in the subbituminous coal; however, only a limited number of subbituminous coals have been analyzed by either technique. The chromium in all four coals was trivalent as no evidence was found for the Cr6+ oxidation state in any coal.

Experimental study of desulfurization of Zhong Liang Shau high sulfur coal by flotation

Energy Technology Data Exchange (ETDEWEB)

Jiang, Z.; Huang, B.; Cao, J. [China University of Mining and Technology (China). Beijing Graduate School

1994-12-01

Emission of large amount of SO{sub 2} from combustion of high sulfur coal causes serious environmental pollution. Pre-combustion desulfurization of high sulfur coal has become a necessity. This paper reports test results of fine coal desulfurization with different flotation technology and the effect of pyrite depressant. Test work showed that when the coal sample from Zhong Liang Shau was processed with a Free Jet Flotation Column its pyritic sulfur content was reduced from 3.08% to 0.84%, with 72.22% recovery of combustible matter in clean coal. The concept of Desulfurization Efficiency Index E{sub ds} for comprehensive evaluation of desulfurization process is proposed, which is defined as the product of the ratio of sulfur content reduction of clean coal and the recovery of combustible matters. 6 refs., 4 figs., 3 tabs.

Final Scientific/Technical Report for project “Increasing the Rate and Extent of Microbial Coal to Methane Conversion through Optimization of Microbial Activity, Thermodynamics, and Reactive Transport”

Energy Technology Data Exchange (ETDEWEB)

Fields, Matthew [Montana State Univ., Bozeman, MT (United States)

2018-01-17

Currently, coal bed methane (CBM) wells have a limited lifetime since the rate of methane removal via the installed wells is much faster than the in situ methane production rates. Along with water issues created by large amounts of CBM production water, the short life span of CBM wells is a huge deterrent to the environmental and economic feasibility of CBM production. The process of biogenic methanogenesis can be enhanced via the stimulation of the associated microbial communities that can convert the organic fractions of coal to methane. This process is termed Microbially-Enhanced Coal Bed Methane (MECBM). However, the rates of methane production are still limited and long incubation times are necessary. We hypothesized that the elucidation of chemical and biological parameters that limited MECBM together with thermodynamic considerations would inform strategies to optimize the process under flow conditions. We incorporated microbiological, physicochemical, and engineering processes to develop a more sustainable CBM production scheme with native coal and native microorganisms. The proposed combination of microbial ecology and physiology as well as optimized engineering principles minimized key constraints that impact microbial coal conversion to methane under environmentally relevant conditions. The combined approach for bench-scale tests resulted in more effective and less environmentally burdensome coal-dependent methane production with the potential for H2O and CO2 management.

Quantitative detection of settled coal dust over green canopy

Science.gov (United States)

Brook, Anna; Sahar, Nir

2017-04-01

of a forthcoming environmental hazard are of key interest when considering the effects of pollution. According to the most basic distribution dynamics, dust consists of suspended particulate matter in a fine state of subdivision that are raised and carried by wind. In this context, it is increasingly important to first, understand the distribution dynamics of pollutants, and subsequently develop dedicated tools and measures to control and monitor pollutants in the free environment. The earliest effect of settled polluted dust particles is not always reflected through poor conditions of vegetation or soils, or any visible damages. In most of the cases, it has a quite long accumulation process that graduates from a polluted condition to long-term environmental and health related hazard. Although conducted experiments with pollutant analog powders under controlled conditions have tended to con- firm the findings from field studies (Brook, 2014; Brook and Ben-Dor 2016; Brook, 2016), a major criticism of all these experiments is their short duration. The resulting conclusion is that it is difficult, if not impossible, to determine the implications of long-term exposure to realistic concentrations of pollutants from such short-term studies. In general, the task of unmixing is to decompose the reflectance spectrum into a set of endmembers or principal combined spectra and their corresponding abundances (Bioucas-Dias et al., 2012). This study suggests that the sensitivity of sparse unmixing techniques provides an ideal approach to extract and identify coal dust settled over/upon green vegetation canopy using in situ spectral data collected by portable spectrometer. The optimal NMF algorithms, such as ALS and LPG, are assumed to be the simplest methods that achieve the minimum error. The suggested practical approach includes the following stages: 1. In situ spectral measurements, 2. Near-real-time spectral data analysis, 3. Estimated concentration of coal dust reported as mg

Fundamental study for improvement of dewatering of fine coal/refuse. Annual report, August 1982-August 1983

Energy Technology Data Exchange (ETDEWEB)

Chiang, S.H.; Klinzing, G.E.; Morsi, B.J.; Tierney, J.W.; Adams, J.; Bhat, N.; Binkley, T.; Chi, S.M.; Kakwani, R.; Qamar, I.

1983-09-01

The overall objective of the study is to seek improved methods of dewatering through a better understanding of the filtration and post-filtration processes. As a first step, efforts have been focused on the mechanism of dewatering in terms of basic properties of coal (and refuse) particles and microstructures of filter cakes, and their relations to filtration rate and final moisture content. Pittsburgh seam-Bruceton Mine coal was used as a base coal with experiments also being conducted with Upper Freeport and Illinois No. 6 coals. During the past year, filter cakes from the above coals with widely varied size ranges were micrographically characterized. The effects of a number of surface active agents and of entrapped air bubbles on the filter cake properties were also studied. A module of the network model for calculating single phase permeabilities was completed and tested. The report is divided into four parts: summary and deliverables; work forecast for the 1983-84; detailed descriptions of technical progress for particle/filter cake characterization; theoretical modeling, and enhanced dewatering methods; and appendices. 11 references, 35 figures, 11 tables.

System of optimization computations of five year plans in the coal industry. [USSR

Energy Technology Data Exchange (ETDEWEB)

Goyzman, E I; Korenev, V G

1980-01-01

A system of optimization computations of five year plans is set forth which was developed over a number of years at the Central Scientific Research Institute of Economics and Scientific-Technical Information of the Coal Industry. Basic principles of design and methodological approaches are given which were used in development of the systemas well as levels of administration and information links between them. The report analyzes the characteristics of problems of planning which arise at different stages of formation of the five year plans and discusses possibilities of taking into account these characteristics in optimized models. Economic formulations of problems of optimization of five year plans are given as applied to two levels of administration: at the branch level and at the level of production associations. Economic-mathematical models of optimization of five year plans are developed for each of the levels and their characteristic features described. The primary methodological principles, on the basis of which optimization models were developed are examined. An economic-mathematical model with continuous variables was developed for the branch level of planning. Volumes of recovery according to a group of shafts in the stage of normal operation (stable group) of each production enterprise are adopted as model variables. A system of limitations which includes limitations on volumes and distinguishable resources is formulated. The minimum of operating expenses, minimum of capital investments and maximum of recovery volumes for the planned period can be used as the optimization criteria. An economic-mathematical model which uses integral variable was developed for the production association level.

Occurrence of trace elements in respirable coal dust

International Nuclear Information System (INIS)

Sahoo, B.N.

1991-01-01

Inhalation of fine particles of coal dust contributes significantly to the occurrence of the disease, pneumoconiosis, prevailing in coal mining community. It is not presently known whether only the coal dust or specific chemical compounds or synergistic effects of several compounds associated with respirable coal dust is responsible for the disease, pneumoconiosis. The present paper describes the quantitative determination of ten minor and trace elements in respirable coal dust particles by atomic absorption spectrophotometric methods. The respirable coal dust samples are collected at the mine atmosphere during drilling in coal scams by using Messrs. Casella's Hexlet apparatus specially designed and fitted with horizontal elutriator to collect the respirable coal dust fraction simulating as near as possible to the lung's retention of the coal miners. After destruction of organic matter by wet oxidation and filtering off clay and silica, Fe, Ca, Mg, Na, K, Mn, Cu, Zn, Cd, and Ni were determined directly in the resulting solution by atomic absorption spectrophotometric procedures. The results show that the trace metals are more acute in lower range of size spectrum. Correlation coefficient, enrichment factor and linear regression values and their inverse relationship between the slope and EF values suggest that, in general, the trace metals in respirable particulates are likely to be from coal derived source if their concentrations are likewise high in the coal. The trace metal analytical data of respirable particulates fitted well to the linear regressive equation. The results of the studies are of importance as it may throw some light on the respirable lung disease 'pneumoconiosis' which are predominant in coal mining community. (author). 13 refs., 6 tabs

Determination of moisture in black coal using pulsed nuclear magnetic resonance spectrometry

International Nuclear Information System (INIS)

Cutmore, N.G.; Sowerby, B.D.; Lynch, L.J.; Webster, D.S.

1987-01-01

Pulsed nuclear magnetic resonance (n.m.r.) spectrometry was investigated as a technique for moisture determination in fine product coal from eight Australian coal washeries. Measurements were made on samples of diameter 8 and 12 mm and length 10 and 120 mm at frequencies from 6.5 to 60 MHz. The ratio of intensities of the water and coal components in the free-induction decay signal can be used to determine moisture to within approx. 0.4-0.7 wt% over the range 0-26 wt% moisture, independent of sample density. This accuracy is independent of particle size (up to 1 mm) and little affected by coal rank, sample length or n.m.r. frequency. (author)

The Bulgarian coal and the fluid bed technology

International Nuclear Information System (INIS)

Konstantinov, M.; Georgiev, J.; Lebedov, K.; Petrov, N.

2000-01-01

Because of low-quality of the most of Bulgarian coal and more rigorous ecological restrictions for decreasing of greenhouse gases the fluidized bed technology is the most appropriate combustion technology. A study with a pilot plant aiming to establish the values of technological parameters in view to maintain stable process of fluidized bed combustion at the specific burning characteristics of the Bulgarian coal was carried out. Coal of different quality and particle size production of 'Marbas' LTD mines were used. Series of experiments with batches of strictly determined content were carried out at minimal, average and maximal load. The technological factors as: layer's aerodynamics, layer's height, fuel's quantity and quantity of inert material were changed at each batch. The ecological factors were optimized considering coal's quality, plant's parameters, limestone's dosing and layer's aerodynamics. A regressive model for optimization of technological and ecological factors was created. An average coefficient of performance was achieved, resp. 82.27 % at combustion of coal from mines 'Maritsa-West' and 90 % from mine 'Lev'. A coefficient of sulfur oxides' capture 70 % was obtained at coal with sulfur content 3.1-3.9 %. In conclusion the fluidized bed technology is very suitable for combustion's characteristics of the Bulgarian coal

Causes of coal degradation at working faces

Energy Technology Data Exchange (ETDEWEB)

Sikora, W

1985-01-01

Coal comminution by shearer loaders at working faces and factors influencing it are analyzed. Three groups of factors are evaluated: coal mechanical properties, design and specifications of shearer loaders and mining schemes. On the basis of analyses, recommendations for increasing proportion of coarse coal and reducing coal comminution in underground coal mines in Poland are made. Increasing output of coarse coal in coal seams with a high proportion of dull coal is most economic. Increasing power of drive systems for shearer loaders to 500 kW or more decisively influences grain size distribution of coal and increases proportion of coarse coal, especially in seams of dull coal. Gradually increasing cutting depth of a shearer loader negatively influences haulage speed and coarse coal output. Replacing gradual cutting depth increase by attack at the full cutting depth increases proportion of coarse coal. When medium or thick coal seams are mined a coal bench from 0.3 to 0.5 m thick should be left in the roof or between 2 benches cut by 2 cutting drums. The coal bench left in the face disintegrates under the influence of gravity and the proportion of coarse coal increases. Optimizing yield strength of powered supports at a working face is a further method for improving grain size distribution of coal and increasing proportion of coarse coal. 2 references.

Recent advances in prediction of emission of hazardous air pollutants from coal-fired power plants

International Nuclear Information System (INIS)

Senior, C.L.; Helble, J.J.; Sarofim, A.F.

2000-01-01

Coal-fired power plants are a primary source of mercury discharge into the atmosphere along with fine particulates containing arsenic, selenium, cadmium, and other hazardous air pollutants. Information regarding the speciation of these toxic metals is necessary to accurately predict their atmospheric transport and fate in the environment. New predictive tools have been developed to allow utilities to better estimate the emissions of toxic metals from coal-fired power plants. These prediction equations are based on fundamental physics and chemistry and can be applied to a wide variety of fuel types and combustion conditions. The models have significantly improved the ability to predict the emissions of air toxic metals in fine particulate and gas-phase mercury. In this study, the models were successfully tested using measured mercury speciation and mass balance information collected from coal-fired power plants

A comparison study on the deoxygenation of coal mine methane over coal gangue and coke under microwave heating conditions

International Nuclear Information System (INIS)

Guo, Xuan; Ren, Jun; Xie, Chuanjin; Lin, Jianying; Li, Zhong

2015-01-01

Highlights: • Microwave has great advantages of energy and time saving in CMM deoxygenation. • Microwave pretreatment results in graphitization of carbonaceous materials. • Coal gangue shows benefit in restricting CH 4 decomposition compared to coke. • Under optimal conditions, there is no residual oxygen and CH 4 is less than 2.2%. - Abstract: Microwave heating has great advantages in saving energy and time; in this study, it has been first successfully applied in the deoxidization process of coal mine methane (CMM), where carbon in coal gangue reacts with oxygen in CMM. Compared with traditional heating, microwave pretreatment resulted in rapid heating of coal gangue in CMM deoxygenation, which was attributable to the graphitization of carbonaceous materials. This prominent advantage of microwave heating can contribute to deoxygenation. In addition, deoxygenation effectiveness for both coke and coal gangue under microwave heating was investigated. It was discovered that coke acted as a catalyst to some extent to accelerate methane decomposition. However, this effect could be greatly restricted when coal gangue was used in the deoxygenation process because of its chemical inertness. Under optimal conditions (650 °C and 300 mL/min), there was no residual oxygen in the outlet gas, and methane loss was less than 2.2%

Too Much Coal, too little Oil

NARCIS (Netherlands)

van der Ploeg, F.; Withagen, C.A.A.M.

2012-01-01

Our main message is that it is optimal to use less coal and more oil once one takes account of coal being a backstop which emits much more CO2 than oil. The way of achieving this is to have a steeply rising carbon tax during the initial oil-only phase, a less-steeply rising carbon tax during the

Petrographic characterization of the solid products of coal- pitch coprocessing

Energy Technology Data Exchange (ETDEWEB)

Potter, J.; Kybett, B.D.; McDougall, W.J.; Nambudiri, E.M.V.; Rahimi, P.; Price, J.T.

1986-06-01

Petrographic studies were conducted on four solid residues resulting from the hydrogenation process of 1) Forestburg sub- bituminous coal alone, 2) the coal with a non-coking solvent (anthracene oil), 3) pitch (Cold Lake vacuum-bottom deposits), and 4) a mixture of coal and pitch. The purpose was to determine the amounts of coal and pitch-derived solids in the residues. All the residues were produced under identical severe conditions of liquefaction to promote the formation of solids. The coal processed with anthracene oil gives a residue consisting mainly of isotropic huminitic solids. If the coal is hydrogenated under similar conditions but without a solvent, the predominant residual solids are anisotropic semicokes displaying coarse mosaic textures, which form from vitroplast. The residual products from the hydrogenated Cold Lake vacuum- bottom deposits are also dominantly anisotropic semicokes; these display coarse mosaics and flow textures, and form by the growth and coalescence of mesophase spherules. Both coal- and pitch-derived solids are identified in a residue produced by coprocessing the Forestburg coal with the pitch from the Cold Lake vacuum-bottom deposits. It is concluded that the huminite macerals in the coal generate the fine-grained, mosaic-textured semicokes, whereas the pitch produces the coarse mosaics and flow-textured semicokes.

Source and Enrichment of Toxic Elements in Coal Seams around Mafic Intrusions: Constraints from Pyrites in the Yuandian Coal Mine in Anhui, Eastern China

Directory of Open Access Journals (Sweden)

Yanfei An

2018-04-01

Full Text Available Pyrite, a mineral that can cause potential environmental issues in coal mining, is commonly found in coal seams around intrusions. In this paper, pyrites from the Yuandian Coal Mine (Huaibei Coalfield, Anhui, Eastern China were studied using SEM, Raman and LA-ICP-MS. The pyrite morphologic and geochemical data suggest that (1 four pyrite generations are present (framboidal sedimentary pyrites (Py I in the original coal, coarse-grained magmatic pyrites (Py II in the intruding diabase, fine-grained metamorphic pyrites (Py III in the intrusive contact aureole, and spheroid/vein hydrothermal pyrites (Py IV in the cokeite; and (2 concentrations of cobalt, nickel, arsenic, selenium, lead and copper in the metamorphic pyrites are much higher than the other pyrite generations. We propose that mafic magmatism is the main contributor of the toxic elements to the intrusion-related cokeite at Yuandian.

Pulverized coal burnout in blast furnace simulated by a drop tube furnace

Energy Technology Data Exchange (ETDEWEB)

Du, Shan-Wen [Steel and Aluminum Research and Development Department, China Steel Corporation, Kaohsiung 812 (China); Chen, Wei-Hsin [Department of Greenergy, National University of Tainan, Tainan 700 (China); Lucas, John A. [School of Engineering of the University of Newcastle, Callaghan, NSW 2308 (Australia)

2010-02-15

Reactions of pulverized coal injection (PCI) in a blast furnace were simulated using a drop tube furnace (DTF) to investigate the burnout behavior of a number of coals and coal blends. For the coals with the fuel ratio ranging from 1.36 to 6.22, the experimental results indicated that the burnout increased with decreasing the fuel ratio, except for certain coals departing from the general trend. One of the coals with the fuel ratio of 6.22 has shown its merit in combustion, implying that the blending ratio of the coal in PCI operation can be raised for a higher coke replacement ratio. The experiments also suggested that increasing blast temperature was an efficient countermeasure for promoting the combustibility of the injected coals. Higher fuel burnout could be achieved when the particle size of coal was reduced from 60-100 to 100-200 mesh. However, once the size of the tested coals was in the range of 200 and 325 mesh, the burnout could not be improved further, resulting from the agglomeration of fine particles. Considering coal blend reactions, the blending ratio of coals in PCI may be adjusted by the individual coal burnout rather than by the fuel ratio. (author)

Compressive and tensile strength for concrete containing coal bottom ash

Science.gov (United States)

Maliki, A. I. F. Ahmad; Shahidan, S.; Ali, N.; Ramzi Hannan, N. I. R.; Zuki, S. S. Mohd; Ibrahim, M. H. W.; Azmi, M. A. Mohammad; Rahim, M. Abdul

2017-11-01

The increasing demand in the construction industry will lead to the depletion of materials used in construction sites such as sand. Due to this situation, coal bottom ash (CBA) was selected as a replacement for sand. CBA is a by-product of coal combustion from power plants. CBA has particles which are angular, irregular and porous with a rough surface texture. CBA also has the appearance and particle size distribution similar to river sand. Therefore, these properties of CBA make it attractive to be used as fine aggregate replacement in concrete. The objectives of this study were to determine the properties of CBA concrete and to evaluate the optimum percentage of CBA to be used in concrete as fine aggregate replacement. The CBA was collected at Tanjung Bin power plant. The mechanical experiment (compressive and tensile strength test) was conducted on CBA concrete. Before starting the mechanical experiment, cubic and cylindrical specimens with dimensions measuring 100 × 100 × 100 mm and 150 × 300 mm were produced based on the percentage of coal bottom ash in this study which is 0% as the control specimen. Meanwhile 10%, 20%, 30%, 40%, 50%, 60%, 70%, 80%, 90% and 100% of CBA were used to replace the fine aggregates. The CBA concrete samples were cured for 7 days and 28 days respectively to maintain the rate of hydration and moisture. After the experimental work was done, it can be concluded that the optimum percentage of CBA as fine aggregate is 60% for a curing period of both 7 days and 28 days with the total compressive strength of 36.4 Mpa and 46.2 Mpa respectively. However, the optimum percentage for tensile strength is at 70% CBA for a curing period of both 7 days and 28 days with a tensile strength of 3.03 MPa and 3.63 MPa respectively.

HIGH-QUALITY SELF-COMPACTING CONCRETE WITH COAL BURNING WASTE

Directory of Open Access Journals (Sweden)

Voronin Viktor Valerianovich

2018-01-01

Full Text Available Subject: nowadays self-compacting concretes (SCC, the use of which requires no additional compaction, have become widespread for use in densely-reinforced structures and hard-to-reach places. In self-compacting concretes, finely-ground admixtures-microfillers are widely used for controlling technological properties. Their introduction into the concrete mix allows us to obtain more dense structure of concrete. The influence of micro-fillers on water consumption and plasticity of concrete mix, on kinetics of strength gain rate, heat release and corrosion resistance is also noticeable. Research objectives: the work focuses on the development of composition of self-compacting concrete with assigned properties with the use of fly ash based on coal burning waste, optimized with the help of experimental design method in order to clarify the influence of ash and cement quantity, sand size on strength properties. Materials and methods: pure Portland cement CEM I 42.5 N was used as a binder. Crushed granite of fraction 5…20 mm was used as coarse aggregate, coarse quartz sand with the fineness modulus of 2.6 and fine sand with the fineness modulus of 1.4 were used as fillers. A superplasticizer BASF-Master Glenium 115 was used as a plasticizing admixture. The fly ash from Cherepetskaya thermal power plant was used as a filler. The study of strength and technological properties of self-compacting concrete was performed by using standard methods. Results: we obtained three-factor quadratic dependence of strength properties on the content of ash, cement and fraction of fine filler in the mix of fine fillers. Conclusions: introduction of micro-filler admixture based on the fly ash allowed us to obtain a concrete mix with high mobility, fluidity and self-compaction property. The obtained concrete has high strength characteristics, delayed strength gain rate due to replacement of part of the binder with ash. Introduction of the fly ash increases degree of

Properties of sorbents from brown coal

Energy Technology Data Exchange (ETDEWEB)

Straka, P.; Buchtele, J. [Academy of Sciences of the Czech Republic, Prague (Czech Republic)

2000-07-01

The surface and sorptional properties of carbonaceous materials prepared from brown coal and their relation to minerals content and coal bulk density as technologically important parameters of starting coal were described. Chars were prepared from brown coal of North Bohemian Brown Coal District and activated with CO{sub 2} in a large-scale laboratory unit. Their surface and sorptive properties were investigated. It was found that mineral matter/ash content favourably affects the mesoporosity development in chars/activated chars as the sorption capacity increased with increasing ash content in chars. No influence of ash content on the macroporosity was observed. With the activated chars, both the inner surface and sorption capacity showed the maximum in the burn-off range of 41-64%. Optimization of the process is discussed.

PM1 particles at coal- and gas-fired power plant work areas.

Science.gov (United States)

Hicks, Jeffrey B; McCarthy, Sheila A; Mezei, Gabor; Sayes, Christie M

2012-03-01

With the increased interest in the possible adverse health effects attributed to inhalation of fine particle matter, this study was conducted to gather preliminary information about workplace exposures at coal- and gas-fired power plants to fine particles (PM(1); i.e. <1 μm) and ultrafine particles (i.e. <0.1 μm). Combustion of fossil fuel is known to produce fine particles, and due to their proximity and durations of exposure, power plant workers could be a group of individuals who experience high chronic exposures to these types of particles. The results of a series of real-time instrument measurements showed that concentrations of PM(1) were elevated in some locations in power plants. The highest concentrations were in locations near combustion sources, indicating that combustion materials were leaking from conventional fossil fuel-fired boilers or it was associated with emission plume downwash. Concentrations were the lowest inside air-conditioned control rooms where PM(1) were present at levels similar to or lower than upwind concentrations. Microscopic examinations indicate that PM(1) at the coal-fired plants are dominated by vitrified spheres, although there were also unusual elongated particles. Most of the PM(1) were attached to larger coal fly ash particles that may affect where and how they could be deposited in the lung.

Evaluation of the Emission, Transport, and Deposition of Mercury and Fine Particulate Matter from Coal-Based Power Plants in the Ohio River Valley Region

Energy Technology Data Exchange (ETDEWEB)

Kevin Crist

2008-12-31

As stated in the proposal: Ohio University, in collaboration with CONSOL Energy, Advanced Technology Systems, Inc (ATS) and Atmospheric and Environmental Research, Inc. (AER) as subcontractors, evaluated the impact of emissions from coal-fired power plants in the Ohio River Valley region as they relate to the transport and deposition of mercury and associated fine particulate matter. This evaluation involved two interrelated areas of effort: ambient air monitoring and regional-scale modeling analysis. The scope of work for the ambient air monitoring included the deployment of a surface air monitoring (SAM) station in southeastern Ohio. The SAM station contains sampling equipment to collect and measure mercury (including speciated forms of mercury and wet and dry deposited mercury), particulate matter (PM) mass, PM composition, and gaseous criteria pollutants (CO, NOx, SO2, O3, etc.). Laboratory analyses of time-integrated samples were used to obtain chemical speciation of ambient PM composition and mercury in precipitation. Nearreal- time measurements were used to measure the ambient concentrations of PM mass and all gaseous species including Hg0 and RGM. Approximately 30 months of field data were collected at the SAM site to validate the proposed regional model simulations for episodic and seasonal model runs. The ambient air quality data provides mercury, and fine particulate matter data that can be used by Ohio Valley industries to assess performance on multi-pollutant control systems. The scope of work for the modeling analysis includes (1) development of updated inventories of mercury emissions from coal plants and other important sources in the modeled domain; (2) adapting an existing 3-D atmospheric chemical transport model to incorporate recent advancements in the understanding of mercury transformations in the atmosphere; (3) analyses of the flux of Hg0, RGM, and fine particulate matter in the different sectors of the study region to identify key transport

Application of fractal theory to top-coal caving

International Nuclear Information System (INIS)

Xie, H.; Zhou, H.W.

2008-01-01

The experiences of underground coal mining in China show that coal in a thick hard coal seam with a hard roof, the so-called 'double hard coal seam', is difficult to be excavated by top-coal caving technique. In order to solve the problem, a top-coal weakening technique is proposed in this paper. In the present study, fractal geometry provides a new description of the fracture mechanism for blasting. By means of theoretical analysis of the relationship between the fractal dimension of blasting fragments and the dynamite specific energy, a mechanical model for describing the size distribution of top-coal and the dissipation of blasting energy is proposed. The theoretical results are in agreement with laboratory and in situ test results. Moreover, it is shown that the fractal dimension of coal fragments can be used as an index for optimizing the blasting parameters for a top-coal weakening technique

General programme of energy research: innovation in hard coal, 1974-1977. Preparation and surface facilities. Rahmenprogramm Energieforschung: Innovation Steinkohle, 1974-1977. Aufbereitung und Tagesanlagen)

Energy Technology Data Exchange (ETDEWEB)

1979-01-01

Under the program Preparation and Surface Facilities initiated by the Federal Ministry of Economy of the FRG financial support in the amount of 50% (approx. 17 million DM) of the total project costs was allocated to eight applicants from the mining industry. The Ministry subsidized 15 research projects in the field of coal preparation and handling dealing with: surface blending and storage facilities; the development of a solid bowl centrifuge, steam cowl filter, and reciprocating centrifuge for dewatering coal fines; development of a jig and a screen sizer for coal sizing; clarification units and combustion of waste slurries in a fluidized-bed furnace; computerized monitoring of coal flow in surface and underground installations; the development of a conception for preparing coal otherwise difficult to prepare; and the development of the Olifloc method for agglomeration of coal fines sludge and separation from tailings. (In German)

Fault Detection in Coal Mills used in Power Plants

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Mataji, Babak

2006-01-01

In order to achieve high performance and efficiency of coal-fired power plants, it is highly important to control the coal flow into the furnace in the power plant. This means suppression of disturbances and force the coal mill to deliver the required coal flow, as well as monitor the coal mill...... in order to detect faults in the coal mill when they emerge. This paper deals with the second objective. Based on a simple dynamic model of the energy balance a residual is formed for the coal mill. An optimal unknown input observer is designed to estimate this residual. The estimated residual is following...... tested on measured data of a fault in a coal mill, it can hereby be concluded that this residual is very useful for detecting faults in the coal mill....

Coal as a source of energy to alleviate the crisis facing the cement industry

Energy Technology Data Exchange (ETDEWEB)

Reinert, N

1979-01-01

After recalling the importance of coal in the cement industry up until the end of the 1950s, and the regeneration of interest in this fuel, the author presents some views on the stocking of coal, on its preparation and on its application for firing. The advantages of linear stocking and of de-stocking by the 'front slice' method to ensure good homogenization are described. The precautions to be taken during the fine-grinding process and the transport of the pulverized coal in order to prevent coal-dust explosions are discussed. The main firing systems (direct, semi-direct and indirect) are discussed and their respective advantages and drawbacks examined. (In French)

Design and optimization of the large span dry-coal-shed latticed shell in Liyuan of Henan province

Directory of Open Access Journals (Sweden)

Du Wenfeng

2017-01-01

Full Text Available The design and optimization about the large span dry-coal-shed latticed shell in Liyuan of Henan province were studied. On the basis of the structural scheme of double-layer cylindrical reticulated shell, the optimization scheme of the folding double-layer cylindrical reticulated shell was proposed. Through the analysis of a plurality of calculation models, the optimal geometric parameters were obtained after discussing the influence of different slopes of folding lines and shell thickness on the structural bearing capacity and the amount of steel. The research results show that in the case of the same amount of steel, the ultimate bearing capacity of the double-layer folding cylindrical reticulated shell whose folding line slope is 9% and the shell thickness is about 4.4m can be increased 27.3% compared with the original design scheme.

Effects of bluff-body burner and coal particle size on NOx emissions and burnout

Energy Technology Data Exchange (ETDEWEB)

Xiao, L.S.; Cheng, J.F.; Zeng, H.C. [Huazhong University of Science and Technology, Wuhan (China). National Coal Combustion Lab.

1999-12-01

Investigations on air staging have been carried out using various coals with different degrees of fineness and a variety of burners with a 92.9 kw h{sup -1} tunnel furnace burning pulverized coal. It has been observed that using the bluff-body burner can reduce both the unburned carbon in fly ash and NOx emissions in the case of air staging. The experimental results show that air-staging combustion has a more remarkable effect on NOx reduction for higher-volatile coal than for lower-volatile coal. The results also show that there is a strong influence of coal particle size on NOx emissions and unburned carbon in the fly ash in the case of air staging. 13 refs., 12 figs., 2 tabs.

Briquetability of coal fines from the Lavci deposit near Resen. Briketabilnost sitnih frakcija uglja sa lezista Lavci kod Resena

Energy Technology Data Exchange (ETDEWEB)

Jankuloska, V.; Cadikovska, V. (Rudnici i Zelezarnica, Skopje (Yugoslavia))

1990-01-01

Describes laboratory briquetting of lignite from the Lavci coal deposit in Macedonia, Yugoslavia. The deposit has 21.4 Mt of lignite reserves. Coal samples from cores of exploratory boreholes were evaluated. Chemical composition and properties of the coal are presented. The coal has a 60.8% moisture, 7.8% ash and 0.82% sulfur content. The calorific value of coal is between 5,881 and 7,828 kJ/kg. Coal samples were comminuted and briquetted without binders, due to the favorable petrographic composition of the lignite. Resulting laboratory briquets weighing 45 g were tested for compression strength, water resistance and abrasion (Micum test). Briquet combustion properties were also determined. Briquet quality was of Yugoslav class B[sub 1] and B[sub 2] with the lowest calorific value being 16,427 kJ/kg, which is 2.79 times higher than that of the raw coal. 3 refs.

Gas Emission Prediction Model of Coal Mine Based on CSBP Algorithm

Directory of Open Access Journals (Sweden)

Xiong Yan

2016-01-01

Full Text Available In view of the nonlinear characteristics of gas emission in a coal working face, a prediction method is proposed based on cuckoo search algorithm optimized BP neural network (CSBP. In the CSBP algorithm, the cuckoo search is adopted to optimize weight and threshold parameters of BP network, and obtains the global optimal solutions. Furthermore, the twelve main affecting factors of the gas emission in the coal working face are taken as input vectors of CSBP algorithm, the gas emission is acted as output vector, and then the prediction model of BP neural network with optimal parameters is established. The results show that the CSBP algorithm has batter generalization ability and higher prediction accuracy, and can be utilized effectively in the prediction of coal mine gas emission.

A Comprehensive Review on the Properties of Coal Bottom Ash in Concrete as Sound Absorption Material

Directory of Open Access Journals (Sweden)

Ramzi Hannan Nurul Izzati Raihan

2017-01-01

Full Text Available The government is currently implementing policies to increase the usage of coal as fuel for electricity generation. At the same time, the dependency on gas will be reduced. In addition, coal power plants in Malaysia produce large amounts of industrial waste such as bottom ash which is collected in impoundment ponds (ash pond. However, millions of tons of coal ash (bottom ash waste are collected in ponds near power plant stations. Since bottom ash has been classified as hazardous material that threatens the health and safety of human life, an innovative and sustainable solution has been introduced to reuse or recycle industrial waste such as coal bottom ash in concrete mixtures to create a greener and more sustainable world. Bottom ash has the potential to be used as concrete material to replace fine aggregates, coarse aggregates or both. Hence, this paper provides an overview of previous research which used bottom ash as fine aggregate replacement in conventional concrete. The workability, compressive strength, flexural strength, and sound absorption of bottom ash in concrete are reviewed.

A process for briquetting coal with the production of briquets with high resistance to crushing

Energy Technology Data Exchange (ETDEWEB)

Ono, M; Ito, S; Nakagava, K

1983-02-08

Finely ground coal is mixed with a binder with a softening point of greater than or equal to 30 degrees and with heavy coal tar products, the mixture is molded with the formation of briquets in a two roller press. The mixing is conducted in heated steam or waste gases from a horizontal, helical mixer. The coal is subsequently irrigated by the melted binder and heavy coal tar products. The heavy coal tar products are a bottom residue formed by condensation of volatile products in a gas stream from coking which contains particles of coal and coke. Briquets with a point compression strength of 50 plus or minus 4 kilograms per sq. cur. and a bulk tensity of 1.17 grams per cubic centimeter are produced from a mixture which contains 6 percent binder, 80 percent coal and 20 percent heavy coal tar products.

Mercury in coal and the impact of coal quality on mercury emissions from combustion systems

International Nuclear Information System (INIS)

Kolker, Allan; Senior, Constance L.; Quick, Jeffrey C.

2006-01-01

The proportion of Hg in coal feedstock that is emitted by stack gases of utility power stations is a complex function of coal chemistry and properties, combustion conditions, and the positioning and type of air pollution control devices employed. Mercury in bituminous coal is found primarily within Fe-sulfides, whereas lower rank coal tends to have a greater proportion of organic-bound Hg. Preparation of bituminous coal to reduce S generally reduces input Hg relative to in-ground concentrations, but the amount of this reduction varies according to the fraction of Hg in sulfides and the efficiency of sulfide removal. The mode of occurrence of Hg in coal does not directly affect the speciation of Hg in the combustion flue gas. However, other constituents in the coal, notably Cl and S, and the combustion characteristics of the coal, influence the species of Hg that are formed in the flue gas and enter air pollution control devices. The formation of gaseous oxidized Hg or particulate-bound Hg occurs post-combustion; these forms of Hg can be in part captured in the air pollution control devices that exist on coal-fired boilers, without modification. For a given coal type, the capture efficiency of Hg by pollution control systems varies according to type of device and the conditions of its deployment. For bituminous coal, on average, more than 60% of Hg in flue gas is captured by fabric filter (FF) and flue-gas desulfurization (FGD) systems. Key variables affecting performance for Hg control include Cl and S content of the coal, the positioning (hot side vs. cold side) of the system, and the amount of unburned C in coal ash. Knowledge of coal quality parameters and their effect on the performance of air pollution control devices allows optimization of Hg capture co-benefit

Determining the ash content of coal flotation tailings using an MPOF optical ash meter

Energy Technology Data Exchange (ETDEWEB)

Sikora, T; Sliwa, J

1982-01-01

The block layout, a description of the design and principles of operation of an automatic optical, continuous action MPOF type ash meter are presented. The difference in the optical properties of coal and rock is used in the ash meter. The identification of the ash content is conducted on the basis of the spectral characteristics of reflection of a finely dispersed aqueous coal and rock suspension.

Mathematical optimization techniques for managing selective catalytic reduction for a fleet of coal-fired power plants

Science.gov (United States)

Alanis Pena, Antonio Alejandro

Major commercial electricity generation is done by burning fossil fuels out of which coal-fired power plants produce a substantial quantity of electricity worldwide. The United States has large reserves of coal, and it is cheaply available, making it a good choice for the generation of electricity on a large scale. However, one major problem associated with using coal for combustion is that it produces a group of pollutants known as nitrogen oxides (NO x). NOx are strong oxidizers and contribute to ozone formation and respiratory illness. The Environmental Protection Agency (EPA) regulates the quantity of NOx emitted to the atmosphere in the United States. One technique coal-fired power plants use to reduce NOx emissions is Selective Catalytic Reduction (SCR). SCR uses layers of catalyst that need to be added or changed to maintain the required performance. Power plants do add or change catalyst layers during temporary shutdowns, but it is expensive. However, many companies do not have only one power plant, but instead they can have a fleet of coal-fired power plants. A fleet of power plants can use EPA cap and trade programs to have an outlet NOx emission below the allowances for the fleet. For that reason, the main aim of this research is to develop an SCR management mathematical optimization methods that, with a given set of scheduled outages for a fleet of power plants, minimizes the total cost of the entire fleet of power plants and also maintain outlet NO x below the desired target for the entire fleet. We use a multi commodity network flow problem (MCFP) that creates edges that represent all the SCR catalyst layers for each plant. This MCFP is relaxed because it does not consider average daily NOx constraint, and it is solved by a binary integer program. After that, we add the average daily NOx constraint to the model with a schedule elimination constraint (MCFPwSEC). The MCFPwSEC eliminates, one by one, the solutions that do not satisfy the average daily

Coal background paper. Coal demand

International Nuclear Information System (INIS)

1997-01-01

Statistical data are presented on coal demands in IEA and OECD member countries and in other countries. Coal coaking and coaking coal consumption data are tabulated, and IEA secretariat's coal demand projections are summarized. Coal supply and production data by countries are given. Finally, coal trade data are presented, broken down for hard coal, steam coal, coking coal (imports and export). (R.P.)

Effect of selective catalytic reduction (SCR) on fine particle emission from two coal-fired power plants in China

Science.gov (United States)

Li, Zhen; Jiang, Jingkun; Ma, Zizhen; Wang, Shuxiao; Duan, Lei

2015-11-01

Nitrogen oxides (NOx) emission abatement of coal-fired power plants (CFPPs) requires large-scaled installation of selective catalytic reduction (SCR), which would reduce secondary fine particulate matter (PM2.5) (by reducing nitrate aerosol) in the atmosphere. However, our field measurement of two CFPPs equipped with SCR indicates a significant increase of SO42- and NH4+ emission in primary PM2.5, due to catalytic enhancement of SO2 oxidation to SO3 and introducing of NH3 as reducing agent. The subsequent formation of (NH4)2SO4 or NH4HSO4 aerosol is commonly concentrated in sub-micrometer particulate matter (PM1) with a bimodal pattern. The measurement at the inlet of stack also showed doubled primary PM2.5 emission by SCR operation. This effect should therefore be considered when updating emission inventory of CFPPs. By rough estimation, the enhanced primary PM2.5 emission from CFPPs by SCR operation would offset 12% of the ambient PM2.5 concentration reduction in cities as the benefit of national NOx emission abatement, which should draw attention of policy-makers for air pollution control.

The development of coal-based technologies for Department of Defense facilities. Volume 1, Technical report. Semiannual technical progress report, September 28, 1994--March 27, 1995

Energy Technology Data Exchange (ETDEWEB)

Miller, B.G.; Bartley, D.A.; Hatcher, P. [Pennsylvania State Univ., University Park, PA (United States). Energy and Fuels Research Center] [and others

1996-10-15

This program is being conducted as a cooperative agreement between the Consortium for Coal Water Mixture Technology and the U.S. Department of Energy. Activities this reporting period are summarized by phase. Phase I is nearly completed. During this reporting period, coal beneficiation/preparation studies, engineering designs and economics for retrofitting the Crane, Indiana boiler to fire coal-based fuels, and a 1,000-hour demonstration of dry, micronized coal were completed. In addition, a demonstration-scale micronized-coal water mixture (MCWM) preparation circuit was constructed and a 1,000-hour demonstration firing MCWM began. Work in Phase II focused on emissions reductions, coal beneficiation/preparation studies, and economic analyses of coal use. Emissions reductions investigations involved literature surveys of NO{sub x}, SO{sub 2}, trace metals, volatile organic compounds, and fine particulate matter capture. In addition, vendors and engineering firms were contacted to identify the appropriate emissions technologies for the installation of commercial NO{sub x} and SO{sub 2} removal systems on the demonstration boiler. Information from the literature surveys and engineering firms will be used to identify, design, and install a control system(s). Work continued on the refinement and optimization of coal grinding and MCWM preparation procedures, and on the development of advanced processes for beneficiating high ash, high sulfur coals. Work also continued on determining the basic cost estimation of boiler retrofits, and evaluating environmental, regulatory, and regional economic impacts. In addition, the feasibility of technology adoption, and the public`s perception of the benefits and costs of coal usage was studied. A coal market analysis was completed. Work in Phase III focused on coal preparation studies, emissions reductions and economic analyses of coal use.

Brown Coal Dewatering Using Poly (Acrylamide-Co-Potassium Acrylic Based Super Absorbent Polymers

Directory of Open Access Journals (Sweden)

Sheila Devasahayam

2015-09-01

Full Text Available With the rising cost of energy and fuel oils, clean coal technologies will continue to play an important role during the transition to a clean energy future. Victorian brown coals have high oxygen and moisture contents and hence low calorific value. This paper presents an alternative non evaporative drying technology for high moisture brown coals based on osmotic dewatering. This involves contacting and mixing brown coal with anionic super absorbent polymers (SAP which are highly crossed linked synthetic co-polymers based on a cross-linked copolymer of acryl amide and potassium acrylate. The paper focuses on evaluating the water absorption potential of SAP in contact with 61% moisture Loy Yang brown coal, under varying SAP dosages for different contact times and conditions. The amount of water present in Loy Yang coal was reduced by approximately 57% during four hours of SAP contact. The extent of SAP brown coal drying is directly proportional to the SAP/coal weight ratio. It is observed that moisture content of fine brown coal can readily be reduced from about 59% to 38% in four hours at a 20% SAP/coal ratio.

Exploratory research on solvent refined coal liquefaction. Annual technical progress report, January 1-December 31, 1979

Energy Technology Data Exchange (ETDEWEB)

None

1980-09-01

This report summarizes the progress of the Exploratory Research on Solvent Refined Coal Liquefaction project by The Pittsburg and Midway Coal Mining Co.'s Merriam Laboratory during 1979. In a series of experiments with varying feed gas composition, low levels (5 to 10 mole %) of carbon monoxide had little effect on the SRC II processing of Pittsburgh Seam coal (Powhatan No. 5 Mine) while higher levels (20 to 40 mole %) resulted in a general degradation of operability and reduced oil yields. Addition of finely divided (approx. 1 ..mu..m) pyrite to the reactive Powhatan coal had little effect on oil yields although the molecular weight of the distillation residue was apparently decreased. When finely divided pyrite and magnetite were added to the less reactive coals from the Loveridge and Blacksville No. 1 Mines (also Pittsburgh Seam), however, substantial increases in oil yields and product quality were obtained. In a comparison of upflow and downflow dissolver configurations with Powhatan coal in the SRC II mode, there was no difference in yields or product quality. A study characterizing specific reactors revealed a significantly higher conversion in the SRC I mode with a reactor approximating plug flow conditions compared to a completely backmixed reactor. In the SRC II mode there was only a slightly higher oil yield with the plug flow reactor.

Result of design and test operation of a coal boiler at Hyogo Refinery

Energy Technology Data Exchange (ETDEWEB)

Miura, Yasuhiko; Sato, Noriyuki

1987-05-01

This boiler is the first coal boiler for the oil refineries in Japan (Installed in Oct., 1986 at Idemitsu Petrochemical Co.) Causes for using coal as a fuel are a conversion to less expensive fuel and offering a technical service to the users of coal through the combustion of coal and learning of a handling technique. The type of boiler is Babcock single barrel radiant type and has 150 t/d capacity with single fuel combustion of coal. Auxiliary equipments are a pulverizer, a transportation and storage unit, a denitration unit, a dust collector, a desulfurization unit, and an ash disposal unit. Main considerations in the design are measures for the security of finely pulverized coal, clogging prevention for coal and ash. A test operation revealed 7 % of combustible loss and 160 - 250 ppm of NOx content at a charge inlet of denitration unit. Actual operation exhibited no clogging at the denitration unit of troubles due to scaling. Design for raw materials is to blend 4 imported coals (from Australia and Canada, etc) and 3 Japanese ones. (7 figs, 2 tabs)

Gasification of brown coal and char with carbon dioxide in the presence of finely dispersed iron catalysts

Energy Technology Data Exchange (ETDEWEB)

Asami, K.; Sears, P.; Furimsky, E.; Ohtsuka, Y. [Osaka City University, Osaka (Japan). Dept. of Applied Chemistry

1996-05-01

Gasification of brown coal and char with CO{sub 2} using iron catalysts precipitated from an aqueous solution of FeCl{sub 3} has been studied. When the pyrolyzed char is gasified in the temperature-programmed mode, the presence of the iron can lower the temperature giving the maximal rate of CO formation by 130-160 K, a larger lowering being observed at a higher loading in the range of {le} 3 wt% Fe. The specific rates of the isothermal gasification iron-bearing chars at 1173 and 1223 K increase with increasing char conversion, resulting in complete gasification within a short reaction time. Comparison of the initial rates of uncatalyzed and catalyzed gasification reveals that iron addition can lower the reaction temperature by 120 K. Moessbauer spectra show that the precipitation iron exists as fine FeOOH particles, which are reduced mainly to Fe{sub 3}C on charring at 1123 K. Most of the Fe{sub 3}C is transformed into {alpha}-Fe and {gamma}-Fe at the initial stage of gasification, and subsequently these species are oxidized to FeO and Fe{sub 3}O{sub 4}. The changes during gasification are discussed in terms of solid-gas and solid-solid reactions. 23 refs., 10 figs.

Formation of N{sub 2} during the fixed-bed pyrolysis of coals

Energy Technology Data Exchange (ETDEWEB)

Wu, Zhiheng; Ohtsuka, Yasuo [Tohoku Univ., Sendai (Japan); Furimsky, E. [Natural Resources Canada, Ottawa, Ontario (Canada)

1995-12-31

Research on the fate of the nitrogen in coal during pyrolysis has attracted increased attention, since it is related with the NO{sub x} and N{sub 2}O emissions during subsequent combustion. It has been reported that coal nitrogen is initially released as tar, which is then converted to HCN and NH{sub 3} through secondary decomposition reactions. However, little attention to N{sub 2} has been paid so far. We have recently found that N{sub 2} is the dominant product in slow heating rate pyrolysis of a subbituminous coal, and that the finely dispersed iron catalyst promotes drastically the formation of N{sub 2} from a brown coal. If coal nitrogen can be removed efficiently as N{sub 2} during pyrolysis, this method would contribute to the reduction of the NO{sub x} and N{sub 2}O emissions, since such pollutants originate mostly from coal nitrogen. Therefore the present study aims at making clear the influence of coal type, pyrolysis conditions, demineralization, and iron catalyst on the formation of N{sub 2} during the fix-bed pyrolysis of several coals with different ranks.

Gondwana basins and their coal resources in Bangladesh

International Nuclear Information System (INIS)

Nehaluddin, M.; Sultan-ul-Islam, M.

1994-01-01

Fault bounded five Gondwana basins have been discovered in the north western Bangladesh. Among these basins show considerable amount of coal deposits. The Gondwana rocks are highly formed during the Permo-carboniferous diastrophism and later on acquired dynamic characters. In almost all basins, the Permian rocks overlie the Precambrian basement and underlie either the Tertiary or the Cretaceous sediments, structural, stratigraphic, and depositional history of these basins is more or less similar. The sedimentary sequences are composed of light to dark gray, fine to very coarse grained, sub angular to sub rounded felspathic sandstone, dark grey carbonaceous shale and sandstone, variegated conglomerate and thick coal seams (single seam max. 42.38m). The rocks are often alternated and bear the characteristics of cyclic sedimentation. The depositional environments varied from restricted drainage to open fluvial dominated low to moderate sinuous drainage system. The coal bearing basins were flanked by vegetated and swampy over bank. Age of these coals is suggested to be the late permian. Proved and probable reserves of coal in Jamalganj-Paharpur basin are 670 and 1,460 million metric tons, in Barapukuria basin 303 and 3899 million metric tons; in Barapukuria basin 303 and 389 million metric tons; and in Khalaspir basin 143 and 685 million metric tons respectively. The coal is high volatile, low sulphur, bituminous type. It can be used for different forms of thermal conversion. (author)

Co-combustion characteristics and blending optimization of tobacco stem and high-sulfur bituminous coal based on thermogravimetric and mass spectrometry analyses.

Science.gov (United States)

Zhang, Kaihua; Zhang, Kai; Cao, Yan; Pan, Wei-ping

2013-03-01

Despite much research on co-combustion of tobacco stem and high-sulfur coal, their blending optimization has not been effectively found. This study investigated the combustion profiles of tobacco stem, high-sulfur bituminous coal and their blends by thermogravimetric analysis. Ignition and burnout performances, heat release performances, and gaseous pollutant emissions were also studied by thermogravimetric and mass spectrometry analyses. The results indicated that combustion of tobacco stem was more complicated than that of high-sulfur bituminous coal, mainly shown as fixed carbon in it was divided into two portions with one early burning and the other delay burning. Ignition and burnout performances, heat release performances, and gaseous pollutant emissions of the blends present variable trends with the increase of tobacco stem content. Taking into account the above three factors, a blending ratio of 0–20% tobacco stem content is conservatively proposed as optimum amount for blending. Copyright © 2012 Elsevier Ltd. All rights reserved.

Significance and development of the utilization of brown coal high temperature coke in the economy of the GDR for the period 1964 to 1974

Energy Technology Data Exchange (ETDEWEB)

Klose, E.; Heschel, W.

1979-01-01

Brown coal high temperature coke production in GDR in the years since 1964 is described. In 1969 the second large brown coal high temperature coking plant, Schwarze Pumpe, went into operation, increasing the total brown coal high temperature coke production to 2 million tons annually. Utilization of the coke size classes in mm from 0-3.15, 3.15-20, 20-31.5, 31.5-45 and greater than 45 mm in the metallurgical, chemical, and energy industries as well as for household heating is shown with figures from 1964, 1970 and 1974. The increasing use of coke in households partly as briquet substitution is also shown (in 1970 42% of the coke was used in households). The substitution of black coal coke by brown coal coke in additional fields of industrial production was also further advanced. Coke production at the Schwarze Pumpe plant is scheduled to increase to 1.6 million tons by 1985 by means of the application of improved coking technologies. Investigations for future industrial solutions to the following coking problems are being conducted: processing coke fines (which make up 10 to 12% of the total produced coke) by briquetting with binders into formed coke, firing coke fines in blast furnaces and power plants, mixed briquetting of coke fines with limestone for carbide production and mixed briquetting of coke and ore fines for metallurgical purposes. (8 refs.) (In German)

Dissolution and transport of coal tar compounds in fractured clay-rich residuum

DEFF Research Database (Denmark)

Vulava, Vijay M.; McKay, Larry D.; Broholm, Mette Martina

2012-01-01

the importance of rapid dissolution and transport through the fracture networks. The concentrations continued to rise but did not reach the corresponding effective solubility limit in most cases. Compounds that were less soluble and those that were more susceptible to sorption or matrix diffusion eluted...... at a much slower rate. Analysis of contaminant concentrations in microcore residuum samples indicated that all 10 compounds had spread throughout the entire monolith and had diffused into the fine-grained matrix between fractures. These data suggest that the predominantly fine pore structure did not appear......We investigated the dissolution and transport of organic contaminants from a crude coal tar mixture in a monolith of fractured clay-rich residuum. An electrolyte solution was eluted through the residuum monolith containing a small emplaced source of coal tar under biologically inhibited and mildly...

Coal-water slurries containing petrochemicals to solve problems of air pollution by coal thermal power stations and boiler plants: An introductory review.

Science.gov (United States)

Dmitrienko, Margarita A; Strizhak, Pavel A

2018-02-01

This introductory study presents the analysis of the environmental, economic and energy performance indicators of burning high-potential coal water slurries containing petrochemicals (CWSP) instead of coal, fuel oil, and natural gas at typical thermal power stations (TPS) and a boiler plant. We focus on the most hazardous anthropogenic emissions of coal power industry: sulfur and nitrogen oxides. The research findings show that these emissions may be several times lower if coal and oil processing wastes are mixed with water as compared to the combustion of traditional pulverized coal, even of high grades. The study focuses on wastes, such as filter cakes, oil sludge, waste industrial oils, heavy coal-tar products, resins, etc., that are produced and stored in abundance. Their deep conversion is very rare due to low economic benefit. Effective ways are necessary to recover such industrial wastes. We present the cost assessment of the changes to the heat and power generation technologies that are required from typical power plants for switching from coal, fuel oil and natural gas to CWSPs based on coal and oil processing wastes. The corresponding technological changes pay off after a short time, ranging from several months to several years. The most promising components for CWSP production have been identified, which provide payback within a year. Among these are filter cakes (coal processing wastes), which are produced as a ready-made coal-water slurry fuel (a mixture of flocculants, water, and fine coal dust). These fuels have the least impact on the environment in terms of the emissions of sulfur and nitrogen oxides as well as fly ash. An important conclusion of the study is that using CWSPs based on filter cakes is worthwhile both as the main fuel for thermal power stations and boiler plants and as starting fuel. Copyright © 2017 Elsevier B.V. All rights reserved.

Natural radioactivity product from coal burning in PLTU Pacitan

International Nuclear Information System (INIS)

Sukirno; Sri Murniasih; Rosidi; Sutanto WW

2016-01-01

Monitoring of radioactivity in the coal-fired power plant has been carried out in the CAST-NAA laboratory at 2015. Monitoring includes analysis of soil, water, fly ash, bottom ash and coal. The basic purpose of this work is the investigation of natural radionuclide contents in coal and the actual product samples in the Pacitan power plant as a first step to estimate the radioactive in the vicinity. This paper presents the results of the analysis of radioactivity in samples of coal, fly ash and bottom ash as well as environment samples of soil and water. Ra-226, Th-232, K-40, U-235, U-238, and Pb-210 Natural radionuclides are determined by gamma spectrometry with HPGe detector. Natural radionuclide in fine grain coal, bottom ash and fly ash have concentrations range (162.182 to 0.057) Bq/kg. Radioactivity contained in soil ranges (0.041 to 169.34) Bq/kg, whereas in water ranges (0.003 to 0.045) Bq/L. According Perka BAPETEN. No. 7 of 2013. On Boundary Value Environmental Radioactivity, the results of measurement analysis contained water around the power plant Pacitan still below the limit values allowed by BAPETEN. (author)

A comparative study on prediction methods for China's medium- and long-term coal demand

International Nuclear Information System (INIS)

Li, Bing-Bing; Liang, Qiao-Mei; Wang, Jin-Cheng

2015-01-01

Given the dominant position of coal in China's energy structure and in order to ensure a safe and stable energy supply, it is essential to perform a scientific and effective prediction of China's medium- and long-term coal demand. Based on the historical data of coal consumption and related factors such as GDP (Gross domestic product), coal price, industrial structure, total population, energy structure, energy efficiency, coal production and urbanization rate from 1987 to 2012, this study compared the prediction effects of five types of models. These models include the VAR (vector autoregressive model), RBF (radial basis function) neural network model, GA-DEM (genetic algorithm demand estimation model), PSO-DEM (particle swarm optimization demand estimation model) and IO (input–output model). By comparing the results of different models with the corresponding actual coal consumption, it is concluded that with a testing period from 2006 to 2012, the PSO-DEM model has a relatively optimal predicted effect on China's total coal demand, where the MAPE (mean absolute percentage error) is close to or below 2%. - Highlights: • The prediction effects of five methods for China's coal demand were compared. • Each model has acceptable prediction results, with MAPE below 5%. • Particle swarm optimization demand estimation model has better forecast efficacy.

Coal waste management practices in the USA:an overview

Institute of Scientific and Technical Information of China (English)

Yoginder P. Chugh; Paul T. Behum

2014-01-01

This paper provides an overview of coal waste management practices with two case studies and an estimate of management cost in 2010 US dollars. Processing of as-mined coal typically results in considerable amount of coarse and fine coal processing wastes because of in-seam and out-of-seam dilution mining. Processing plant clean coal recovery values run typically 50%–80%. Trace metals and sulfur may be present in waste materials that may result in leachate water with corrosive charac-teristics. Water discharges may require special measures such as liner and collection systems, and treatment to neutralize acid drainage and/or water quality for trace elements. The potential for variations in coal waste production and quality depends upon mining or processing, plus the long-term methods of waste placement. The changes in waste generation rates and engineering properties of the coal waste during the life of the facility must be considered. Safe, economical and environmentally acceptable management of coal waste involves consideration of geology, soil and rock mechanics, hydrology, hydraulics, geochemistry, soil science, agronomy and environmental sciences. These support all aspects of the regulatory environment including the design and construction of earth and rock embankments and dams, as well as a wide variety of waste disposal structures. Development of impoundments is critical and require considerations of typical water-impounding dams and additional requirements of coal waste disposal impoundments. The primary purpose of a coal waste disposal facility is to dispose of unusable waste materials from mining. However, at some sites coal waste impoundments serve to provide water storage capacity for processing and flood attenuation.

Study on Gas Field Optimization Distribution with Parameters Adjustment of the Air Duct Outlet for Mechanized Heading Face in Coal Mine

Science.gov (United States)

Gong, Xiao-Yan; Zhang, Xin-Yi; Wu, Yue; Xia, Zhi-Xin; Li, Ying

2017-12-01

At present, as the increasingly drilling dimensions with cross-section expansion and distance prolong in coal mine, the situation of gas accumulation in mechanized heading face becomes severe. In this paper, optimization research of gas distribution was carried out by adjusting parameters of the air duct outlet, including angle, caliber and the front and rear distance of air duct outlet. Mechanized heading face of Ningtiaota coal mine was taken as the research object, simulated and analyzed the problems of original gas field, the reasonable parameters range of the air duct outlet was determined according to the allowable range of wind speed and the effect of gas dilution, the adjustment range of each parameter of the air duct outlet is preliminarily determined. Base on this, the distribution of gas field under different parameters adjustment of air duct outlet was simulated. The specific parameters under the different distance between the air duct outlet and the mechanized heading face were obtained, and a new method of optimizing the gas distribution by adjusting parameters of the air duct outlet was provided.

Decision-Related Activity in Macaque V2 for Fine Disparity Discrimination Is Not Compatible with Optimal Linear Readout.

Science.gov (United States)

Clery, Stephane; Cumming, Bruce G; Nienborg, Hendrikje

2017-01-18

Fine judgments of stereoscopic depth rely mainly on relative judgments of depth (relative binocular disparity) between objects, rather than judgments of the distance to where the eyes are fixating (absolute disparity). In macaques, visual area V2 is the earliest site in the visual processing hierarchy for which neurons selective for relative disparity have been observed (Thomas et al., 2002). Here, we found that, in macaques trained to perform a fine disparity discrimination task, disparity-selective neurons in V2 were highly selective for the task, and their activity correlated with the animals' perceptual decisions (unexplained by the stimulus). This may partially explain similar correlations reported in downstream areas. Although compatible with a perceptual role of these neurons for the task, the interpretation of such decision-related activity is complicated by the effects of interneuronal "noise" correlations between sensory neurons. Recent work has developed simple predictions to differentiate decoding schemes (Pitkow et al., 2015) without needing measures of noise correlations, and found that data from early sensory areas were compatible with optimal linear readout of populations with information-limiting correlations. In contrast, our data here deviated significantly from these predictions. We additionally tested this prediction for previously reported results of decision-related activity in V2 for a related task, coarse disparity discrimination (Nienborg and Cumming, 2006), thought to rely on absolute disparity. Although these data followed the predicted pattern, they violated the prediction quantitatively. This suggests that optimal linear decoding of sensory signals is not generally a good predictor of behavior in simple perceptual tasks. Activity in sensory neurons that correlates with an animal's decision is widely believed to provide insights into how the brain uses information from sensory neurons. Recent theoretical work developed simple

Coal waste slurries as a fuel for integrated gasification combined cycle plants

Directory of Open Access Journals (Sweden)

Lutynski Marcin A.

2016-01-01

Full Text Available The article summarizes recent development in integrated gasification combined cycle technology and lists existing and planned IGCC plants. A brief outlook on the IGCC gasification technology is given with focus on entrained-flow gasifiers where the low-quality coal waste slurry fuel can be used. Desired properties of coal and ash for entrained-flow gasifiers are listed. The coal waste slurries, which were deposited at impoundments in Upper Silesian Coal Basin, were considered as a direct feed for such gasifiers. The average ash content, moisture content and lower heating value were analysed and presented as an average values. Entrained-flow commercial gasifiers can be considered as suitable for the coal slurry feed, however the ash content of coal slurries deposited in impoundments is too high for the direct use as the feed for the gasifiers. The moisture content of slurries calculated on as received basis meets the requirements of entrained-flow slurry feed gasifiers. The content of fines is relatively high which allow to use the slurries in entrained-flow gasifiers.

Effect of reaction temperature on the PM10 features during coal combustion

International Nuclear Information System (INIS)

Sui, J.C.; Du, Y.G.; Liu, Q.C.

2008-01-01

Coal-fired power plants produce fine fly ash consisting of particulate matter (PM). Particulate matter less than 10 micrometers in aerodynamic diameter (PM 1 0) is of significant concern because of its adverse environmental and health impacts. This paper studied the effect of reaction temperature on particulate matter (PM 1 0) emission and its chemical composition. The emission characteristics and elemental partition of PM 1 0 from coal combustion were investigated in a drop tube furnace. The paper discussed the experimental apparatus and conditions as well as the coal properties and sample analysis. Liupanshui (LPS) bituminous coal from China was used for the study. The fuel composition of LPS coal and the composition of low temperature ash of Chinese LPS coal were described. The paper also presented the results of the study with reference to particle size distribution and emission characteristic of PM 1 0; elemental partition within PM 1 0; and effect of the reaction temperature on elemental partition within PM 1 0. The PM mass size distribution was found to be bimodal. 14 refs., 2 tabs., 6 figs

MINIMIZATION OF CARBON LOSS IN COAL REBURNING

International Nuclear Information System (INIS)

Zamansky, Vladimir M.; Lissianski, Vitali V.

2001-01-01

This project develops Fuel-Flexible Reburning (FFR), which combines conventional reburning and Advanced Reburning (AR) technologies with an innovative method of delivering coal as the reburning fuel. The overall objective of this project is to develop engineering and scientific information and know-how needed to improve the cost of reburning via increased efficiency and minimized carbon in ash and move the FFR technology to the demonstration and commercialization stage. Specifically, the project entails: (1) optimizing FFR with injection of gasified and partially gasified fuels with respect to NO x and carbon in ash reduction; (2) characterizing flue gas emissions; (3) developing a process model to predict FFR performance; (4) completing an engineering and economic analysis of FFR as compared to conventional reburning and other commercial NO x control technologies, and (5) developing a full-scale FFR design methodology. The project started in August 2000 and will be conducted over a two-year period. The work includes a combination of analytical and experimental studies to identify optimum process configurations and develop a design methodology for full-scale applications. The first year of the program included pilot-scale tests to evaluate performances of two bituminous coals in basic reburning and modeling studies designed to identify parameters that affect the FFR performance and to evaluate efficiency of coal pyrolysis products as a reburning fuel. Tests were performed in a 300 kW Boiler Simulator Facility to characterize bituminous coals as reburning fuels. Tests showed that NO x reduction in basic coal reburning depends on process conditions, initial NO x and coal type. Up to 60% NO x reduction was achieved at optimized conditions. Modeling activities during first year concentrated on the development of coal reburning model and on the prediction of NO x reduction in reburning by coal gasification products. Modeling predicted that composition of coal

Weighted sum of gray gases model optimization for numerical investigations of processes inside pulverized coal-fired furnaces

Science.gov (United States)

Crnomarkovic, Nenad; Belosevic, Srdjan; Tomanovic, Ivan; Milicevic, Aleksandar

2017-12-01

The effects of the number of significant figures (NSF) in the interpolation polynomial coefficients (IPCs) of the weighted sum of gray gases model (WSGM) on results of numerical investigations and WSGM optimization were investigated. The investigation was conducted using numerical simulations of the processes inside a pulverized coal-fired furnace. The radiative properties of the gas phase were determined using the simple gray gas model (SG), two-term WSGM (W2), and three-term WSGM (W3). Ten sets of the IPCs with the same NSF were formed for every weighting coefficient in both W2 and W3. The average and maximal relative difference values of the flame temperatures, wall temperatures, and wall heat fluxes were determined. The investigation showed that the results of numerical investigations were affected by the NSF unless it exceeded certain value. The increase in the NSF did not necessarily lead to WSGM optimization. The combination of the NSF (CNSF) was the necessary requirement for WSGM optimization.

Optimal fuel inventory strategies

International Nuclear Information System (INIS)

Caspary, P.J.; Hollibaugh, J.B.; Licklider, P.L.; Patel, K.P.

1990-01-01

In an effort to maintain their competitive edge, most utilities are reevaluating many of their conventional practices and policies in an effort to further minimize customer revenue requirements without sacrificing system reliability. Over the past several years, Illinois Power has been rethinking its traditional fuel inventory strategies, recognizing that coal supplies are competitive and plentiful and that carrying charges on inventory are expensive. To help the Company achieve one of its strategic corporate goals, an optimal fuel inventory study was performed for its five major coal-fired generating stations. The purpose of this paper is to briefly describe Illinois Power's system and past practices concerning coal inventories, highlight the analytical process behind the optimal fuel inventory study, and discuss some of the recent experiences affecting coal deliveries and economic dispatch

Conversion of metallurgical coke and coal using a Coal Direct Chemical Looping (CDCL) moving bed reactor

International Nuclear Information System (INIS)

Luo, Siwei; Bayham, Samuel; Zeng, Liang; McGiveron, Omar; Chung, Elena; Majumder, Ankita; Fan, Liang-Shih

2014-01-01

Highlights: • Accumulated more than 300 operation hours were accomplished for the moving bed reducer reactor. • Different reactor operation variables were investigated with optimal conditions identified. • High conversions of sub-bituminous coal and bituminous coal were achieved without flow problems. • Co-current and counter-current contact modes were tested and their applicability was discussed. - Abstract: The CLC process has the potential to be a transformative commercial technology for a carbon-constrained economy. The Ohio State University Coal Direct Chemical Looping (CDCL) process directly converts coal, eliminating the need for a coal gasifier oran air separation unit (ASU). Compared to other solid-fuel CLC processes, the CDCL process is unique in that it consists of a countercurrent moving bed reducer reactor. In the proposed process, coal is injected into the middle of the moving bed, whereby the coal quickly heats up and devolatilizes, splitting the reactor roughly into two sections with no axial mixing. The top section consists of gaseous fuel produced from the coal volatiles, and the bottom section consists of the coal char mixed with the oxygen carrier. A bench-scale moving bed reactor was used to study the coal conversion with CO 2 as the enhancing gas. Initial tests using metallurgical cokefines as feedstock were conducted to test the effects of operational variables in the bottom section of the moving bed reducer, e.g., reactor temperature, oxygen carrier to char ratio, enhancer gas CO 2 flow rate, and oxygen carrier flow rates. Experiments directly using coal as the feedstock were subsequently carried out based on these test results. Powder River Basin (PRB) coal and Illinois #6 coal were tested as representative sub-bituminous and bituminous coals, respectively. Nearly complete coal conversion was achieved using composite iron oxide particles as the oxygen carriers without any flow problems. The operational results demonstrated that a

Elk Valley Coal innovation paving the way

Energy Technology Data Exchange (ETDEWEB)

Chen, C.; Ednie, H.; Weldon, H.

2006-09-15

Elk Valley Coal maintains performance optimization across its six metallurgical coal operations. Performance, personnel issues, and training are discussed. Programmes at Fording River, Greenhills, and Coal Mountain are described. Fording River is implementing new computer systems and high-speed wireless networks. The pit control system and the equipment maintenance and remote maintenance programmes are being improved. The Glider Kit program to rebuild major equipment is described. Safety and productivity measures at Greenhills include testing and evaluation of innovations such as the Drilling and Blasting System (DABS), a payload monitor on a shovel, and two GPS-based systems. Blasting methods, a timing study that examines wall stability, fragmentation simulation, and the Six Mine structure at Coal Mountain are described. 5 photos.

Problems of clean coals production as a sources of clean energy generation; Problemy produkcji czystych wegli jako zrodlo wytwarzania czystej energii

Energy Technology Data Exchange (ETDEWEB)

Blaschke, W. [Polish Academy of Sciences, Krakow (Poland). Mineral and Energy Economy Institute

2004-07-01

The paper advises of clean coal technology programme objectives. Issues connected with clean coals preparation for combustion have been discussed. The quality of steam fine coals has been presented, including those used in the commercial power industry. A small supply of 'clean coals' has been started in Poland, related however to a limited demand. Factors affecting the reduction in clean coal production have been discussed. The fact that there are no significant reasons to constrain supplies of clean coals has been emphasised. The quality of coal in deposits is very good, and the condition of preparation enables production of clean coal. Clean energy generation from clean coal requires only cooperation between the hard coal mining industry and the commercial power industry, passing over particular sectoral interests. 15 refs.

Trace element emissions from coal

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-09-15

Trace elements are emitted during coal combustion. The quantity, in general, depends on the physical and chemical properties of the element itself, the concentration of the element in the coal, the combustion conditions and the type of particulate control device used, and its collection efficiency as a function of particle size. Some trace elements become concentrated in certain particle streams following combustion such as bottom ash, fly ash, and flue gas particulate matter, while others do not. Various classification schemes have been developed to describe this partitioning behaviour. These classification schemes generally distinguish between: Class 1: elements that are approximately equally concentrated in the fly ash and bottom ash, or show little or no fine particle enrichment, examples include Mn, Be, Co and Cr; Class 2: elements that are enriched in the fly ash relative to bottom ash, or show increasing enrichment with decreasing particle size, examples include As, Cd, Pb and Sb; Class 3: elements which are emitted in the gas phase (primarily Hg (not discussed in this review), and in some cases, Se). Control of class 1 trace elements is directly related to control of total particulate matter emissions, while control of the class 2 elements depends on collection of fine particulates. Due to the variability in particulate control device efficiencies, emission rates of these elements can vary substantially. The volatility of class 3 elements means that particulate controls have only a limited impact on the emissions of these elements.

Stratified Sampling to Define Levels of Petrographic Variation in Coal Beds: Examples from Indonesia and New Zealand

Directory of Open Access Journals (Sweden)

Tim A. Moore

2016-01-01

Full Text Available DOI: 10.17014/ijog.3.1.29-51Stratified sampling of coal seams for petrographic analysis using block samples is a viable alternative to standard methods of channel sampling and particulate pellet mounts. Although petrographic analysis of particulate pellets is employed widely, it is both time consuming and does not allow variation within sampling units to be assessed - an important measure in any study whether it be for paleoenvironmental reconstruction or in obtaining estimates of industrial attributes. Also, samples taken as intact blocks provide additional information, such as texture and botanical affinity that cannot be gained using particulate pellets. Stratified sampling can be employed both on ‘fine’ and ‘coarse’ grained coal units. Fine-grained coals are defined as those coal intervals that do not contain vitrain bands greater than approximately 1 mm in thickness (as measured perpendicular to bedding. In fine-grained coal seams, a reasonable sized block sample (with a polished surface area of ~3 cm2 can be taken that encapsulates the macroscopic variability. However, for coarse-grained coals (vitrain bands >1 mm a different system has to be employed in order to accurately account for the larger particles. Macroscopic point counting of vitrain bands can accurately account for those particles>1 mm within a coal interval. This point counting method is conducted using something as simple as string on a coal face with marked intervals greater than the largest particle expected to be encountered (although new technologies are being developed to capture this type of information digitally. Comparative analyses of particulate pellets and blocks on the same interval show less than 6% variation between the two sample types when blocks are recalculated to include macroscopic counts of vitrain. Therefore even in coarse-grained coals, stratified sampling can be used effectively and representatively.

Effect of Crusher Type and Crusher Discharge Setting On Washability Characteristics of Coal

Science.gov (United States)

Ahila, P.; Battacharya, S.

2018-02-01

Natural resources have been serving the life of many civilizations, among these coals are of prime importance. Coal is the most important and abundant fossil fuel in India. It accounts for 55% of the country’s energy need. Coal will continue as the mainstay fuel for power generation. Previous researches has been made about the coal feed size and coal type had great influence on the crushing performance of the same jaw crusher and amount of fines generated from a particular coal depends not only upon coal friability but also on crusher type. Therefore, it necessitates crushing and grinding the coal for downstream process. In this paper the effect of crusher type and crusher discharge setting on washability characteristics of same crushed non-coking coal has been studied. Thus four different crushers were investigated at variable parameters like discharge settings, different capacities and feed openings. The experimental work conducted for all crushers with same feed size and HGI (Hardgrove Grindability Index). Based on the investigation the results indicate that the four crushers which has been involved for the experimental work shows that the variation in not only the product size distribution and also reduction ratio. Maximum breakage has been occurred at coarsest size fraction of irrespective of crusher type and discharge setting.

EVALUATION OF THE EMISSION, TRANSPORT, AND DEPOSITION OF MERCURY, FINE PARTICULATE MATTER, AND ARSENIC FROM COAL-BASED POWER PLANTS IN THE OHIO RIVER VALLEY REGION

Energy Technology Data Exchange (ETDEWEB)

Kevin Crist

2004-10-02

Ohio University, in collaboration with CONSOL Energy, Advanced Technology Systems, Inc (ATS) and Atmospheric and Environmental Research, Inc. (AER) as subcontractors, is evaluating the impact of emissions from coal-fired power plants in the Ohio River Valley region as they relate to the transport and deposition of mercury, arsenic, and associated fine particulate matter. This evaluation will involve two interrelated areas of effort: ambient air monitoring and regional-scale modeling analysis. The scope of work for the ambient air monitoring will include the deployment of a surface air monitoring (SAM) station in southeastern Ohio. The SAM station will contain sampling equipment to collect and measure mercury (including speciated forms of mercury and wet and dry deposited mercury), arsenic, particulate matter (PM) mass, PM composition, and gaseous criteria pollutants (CO, NOx, SO{sub 2}, O{sub 3}, etc.). Laboratory analysis of time-integrated samples will be used to obtain chemical speciation of ambient PM composition and mercury in precipitation. Near-real-time measurements will be used to measure the ambient concentrations of PM mass and all gaseous species including Hg{sup 0} and RGM. Approximately of 18 months of field data will be collected at the SAM site to validate the proposed regional model simulations for episodic and seasonal model runs. The ambient air quality data will also provide mercury, arsenic, and fine particulate matter data that can be used by Ohio Valley industries to assess performance on multi-pollutant control systems. The scope of work for the modeling analysis will include (1) development of updated inventories of mercury and arsenic emissions from coal plants and other important sources in the modeled domain; (2) adapting an existing 3-D atmospheric chemical transport model to incorporate recent advancements in the understanding of mercury transformations in the atmosphere; (3) analyses of the flux of Hg{sup 0}, RGM, arsenic, and fine

Evaluation of the Emission, Transport, and Deposition of Mercury, Fine Particulate Matter, and Arsenic from Coal-Based Power Plants in the Ohio River Valley Region

Energy Technology Data Exchange (ETDEWEB)

Kevin Crist

2006-04-02

As stated in the proposal: Ohio University, in collaboration with CONSOL Energy, Advanced Technology Systems, Inc (ATS) and Atmospheric and Environmental Research, Inc. (AER) as subcontractors, is evaluating the impact of emissions from coal-fired power plants in the Ohio River Valley region as they relate to the transport and deposition of mercury, arsenic, and associated fine particulate matter. This evaluation will involve two interrelated areas of effort: ambient air monitoring and regional-scale modeling analysis. The scope of work for the ambient air monitoring will include the deployment of a surface air monitoring (SAM) station in southeastern Ohio. The SAM station will contain sampling equipment to collect and measure mercury (including speciated forms of mercury and wet and dry deposited mercury), arsenic, particulate matter (PM) mass, PM composition, and gaseous criteria pollutants (CO, NO{sub x}, SO{sub 2}, O{sub 3}, etc.). Laboratory analysis of time-integrated samples will be used to obtain chemical speciation of ambient PM composition and mercury in precipitation. Near-real-time measurements will be used to measure the ambient concentrations of PM mass and all gaseous species including Hg0 and RGM. Approximately 18 months of field data will be collected at the SAM site to validate the proposed regional model simulations for episodic and seasonal model runs. The ambient air quality data will also provide mercury, arsenic, and fine particulate matter data that can be used by Ohio Valley industries to assess performance on multi-pollutant control systems. The scope of work for the modeling analysis will include (1) development of updated inventories of mercury and arsenic emissions from coal plants and other important sources in the modeled domain; (2) adapting an existing 3-D atmospheric chemical transport model to incorporate recent advancements in the understanding of mercury transformations in the atmosphere; (3) analyses of the flux of Hg{sup 0

Evaluation of the Emission, Transport, and Deposition of Mercury, Fine Particulate Matter, and Arsenic from Coal-Based Power Plants in the Ohio River Valley Region

Energy Technology Data Exchange (ETDEWEB)

Kevin Crist

2005-10-02

Ohio University, in collaboration with CONSOL Energy, Advanced Technology Systems, Inc (ATS) and Atmospheric and Environmental Research, Inc. (AER) as subcontractors, is evaluating the impact of emissions from coal-fired power plants in the Ohio River Valley region as they relate to the transport and deposition of mercury, arsenic, and associated fine particulate matter. This evaluation will involve two interrelated areas of effort: ambient air monitoring and regional-scale modeling analysis. The scope of work for the ambient air monitoring will include the deployment of a surface air monitoring (SAM) station in southeastern Ohio. The SAM station will contain sampling equipment to collect and measure mercury (including speciated forms of mercury and wet and dry deposited mercury), arsenic, particulate matter (PM) mass, PM composition, and gaseous criteria pollutants (CO, NOx, SO{sub 2}, O{sub 3}, etc.). Laboratory analysis of time-integrated samples will be used to obtain chemical speciation of ambient PM composition and mercury in precipitation. Near-real-time measurements will be used to measure the ambient concentrations of PM mass and all gaseous species including Hg{sup 0} and RGM. Approximately of 18 months of field data will be collected at the SAM site to validate the proposed regional model simulations for episodic and seasonal model runs. The ambient air quality data will also provide mercury, arsenic, and fine particulate matter data that can be used by Ohio Valley industries to assess performance on multi-pollutant control systems. The scope of work for the modeling analysis will include (1) development of updated inventories of mercury and arsenic emissions from coal plants and other important sources in the modeled domain; (2) adapting an existing 3-D atmospheric chemical transport model to incorporate recent advancements in the understanding of mercury transformations in the atmosphere; (3) analyses of the flux of Hg0, RGM, arsenic, and fine

International Coal Report's coal year 1991

Energy Technology Data Exchange (ETDEWEB)

McCloskey, G [ed.

1991-05-31

Following introductory articles on factors affecting trade in coal and developments in the freight market, tables are given for coal exports and coal imports for major countries worldwide for 1989 and 1990. Figures are also included for coal consumption in Canada and the Eastern bloc,, power station consumption in Japan, coal supply and demand in the UK, electric utility coal consumption and stocks in the USA, coal production in Australia, Canada and USA by state, and world hard coal production. A final section gives electricity production and hard coal deliveries in the EEC, sales of imported and local coal and world production of pig iron and steel.

Effect of frothing and collecting agents for flotation behavior of coal

International Nuclear Information System (INIS)

Nasir, S.; Sheikh, T.S.

2011-01-01

Coal flotation is a complex process involving several phases (particles, oil droplets and air bubbles). These phases simultaneously interact with each other and with other species such as the molecules of a promoting reagent and dissolved ions in water. The physical and chemical interactions determine the outcome of the flotation process. Although the interactions between the oil droplets and coal particles are actually favored, stabilization of the oil droplets by small amounts of fine hydrophobic particles may lead to decrease in selectivity and an increased in oil consumption. These problems could be remedied by use of promoters that modify the coal surface for suitable particle-particle, droplet-particle and particle-bubble contact while emulsifying the oil droplets. In this paper, a detailed description of the coal flotation, their physical and chemical interactions with each other in the flotation pulp, the major parameters (% volatiles, % fixed carbon and heating value) that affect these interactions and how these interactions, in turn, influence the flotation process are discussed. (author)

Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash

Directory of Open Access Journals (Sweden)

Martin Ernesto Kalaw

2016-07-01

Full Text Available Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC, which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1 their technical properties are comparable if not better; (2 they can be produced from industrial wastes; and (3 within reasonable constraints, their production requires less energy and emits significantly less CO2. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA and coal bottom ash (CBA, and rice hull ash (RHA. The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF for elemental and X-ray diffraction (XRD for mineralogical composition. The raw materials’ thermal stability and loss on ignition (LOI were determined using thermogravimetric analysis (TGA and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR

Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash.

Science.gov (United States)

Kalaw, Martin Ernesto; Culaba, Alvin; Hinode, Hirofumi; Kurniawan, Winarto; Gallardo, Susan; Promentilla, Michael Angelo

2016-07-15

Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC), which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1) their technical properties are comparable if not better; (2) they can be produced from industrial wastes; and (3) within reasonable constraints, their production requires less energy and emits significantly less CO₂. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC) use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA) and coal bottom ash (CBA), and rice hull ash (RHA). The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF) for elemental and X-ray diffraction (XRD) for mineralogical composition. The raw materials' thermal stability and loss on ignition (LOI) were determined using thermogravimetric analysis (TGA) and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP) analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR), scanning

Development of an inexact optimization model for coupled coal and power management in North China

International Nuclear Information System (INIS)

Liu, Y.; Huang, G.H.; Cai, Y.P.; Cheng, G.H.; Niu, Y.T.; An, K.

2009-01-01

In this study, an inexact coupled coal and power management (ICCPM) model was developed for planning coupled coal and power management systems through integrating chance-constrained programming (CCP), interval linear programming (ILP) and mixed integer linear programming (MILP) techniques. The ICCPM model can effectively handle uncertainties presented in terms of probability density functions and intervals. It can also facilitate dynamic analysis of capacity expansions, facility installation and coal inventory planning within a multi-period and multi-option context. Complexities in coupled coal and power management systems can be systematically reflected in this model, thus applicability of the modeling process would be highly enhanced. The developed ICCPM model was applied to a case of long-term coupled coal and power management systems planning in north China. Interval solutions associated with different risk levels of constraint violations have been obtained, which can be used for generating decision alternatives and helping identify desired policies. The generated results can also provide desired solutions for coal and power generation, capacity initiation and expansion, and coal blending with a minimized system cost, a maximized system reliability and a maximized coal transportation security. Tradeoffs between system costs and constraint-violation risks can also be tackled.

Analytical study on U/G coal mine CPT and inferences

Energy Technology Data Exchange (ETDEWEB)

Dey, N.C.; Mukhopadhyay, S. [Bengal Engineering College, Howrath (India). Dept. of Mining and Geology

1999-08-01

The analytical aspects of underground CPT (coal mine cost per tonne), which varies from mine to mine due to the different weightages of various contributing factors, are described. The CPT is not only dictated by the increasing wages but also by the availability of man-hour and accountability of machine utilization. An optimal blend of labour-intensive and machine-intensive methods involving least investment and operating cost, is a challenge for the coal industry. Technology upgradation and implementation, higher skill and morale, excellence in planning and monitoring, optimization in capacity utilization, and better consumer acceptability of coal will consistently improve the financial health of the coal mining sector. Other factors which will help improve the financial health of coal mining industries are (1) cost propaganda like safety week celebration; (2) cost consciousness at all levels; (3) noticeboard comprising the cost of man-hour and machine- hour; (4) no idle time for men as well as machine; (5) care to increase the life of machines; (6) scope of target amendment in a year; (7) prior to introducing costly machines, due weightage to be given on coal grade, mine life, geo-mining conditions; and (8) award to most economic mine and punishment to others rated below the BEP (break- even point). 2 refs., 3 figs.

Studies for the stabilization of coal-oil mixtures. Final report, August 1978-May 1981

Energy Technology Data Exchange (ETDEWEB)

Botsaris, G.D.; Glazman, Y.M.; Adams-Viola, M.

1981-01-01

A fundamental understanding of the stabilization of coal-oil mixtures (COM) was developed. Aggregation of the coal particles was determined to control both the sedimentation and rheological properties of the COM. Sedimentation stability of COM prepared with coal, 80% < 200 mesh, is achieved by particle aggregation, which leads to the formation of a network of particles throughout the oil. The wettability of coal powders was evaluated by the Pickering emulsion test and a spherical agglomeration test to assess its effect on the stability of various COM formulations. Sedimentation stability of hydrophilic coal-oil-water mixtures (COWM) involves the formation of water bridges between the coal particles, while less stabilization of oleophilic COWM is achieved by the formation of an emulsion. Anionic SAA were least sensitive to the coal type and enhanced the aggregation stability of the suspension. The effect of cationic SAA, nonionic SAA and polymer additives depended upon the specific chemical structure of the SAA, the water content of the COM and the type of coal. The sedimentation stability of ultrafine COM was not directly due to the fineness of the powder but due to the formation of a network of flocculated particles.

MINIMIZATION OF CARBON LOSS IN COAL REBURNING

Energy Technology Data Exchange (ETDEWEB)

Vladimir M. Zamansky; Vitali V. Lissianski

2001-09-07

This project develops Fuel-Flexible Reburning (FFR), which combines conventional reburning and Advanced Reburning (AR) technologies with an innovative method of delivering coal as the reburning fuel. The overall objective of this project is to develop engineering and scientific information and know-how needed to improve the cost of reburning via increased efficiency and minimized carbon in ash and move the FFR technology to the demonstration and commercialization stage. Specifically, the project entails: (1) optimizing FFR with injection of gasified and partially gasified fuels with respect to NO{sub x} and carbon in ash reduction; (2) characterizing flue gas emissions; (3) developing a process model to predict FFR performance; (4) completing an engineering and economic analysis of FFR as compared to conventional reburning and other commercial NO{sub x} control technologies, and (5) developing a full-scale FFR design methodology. The project started in August 2000 and will be conducted over a two-year period. The work includes a combination of analytical and experimental studies to identify optimum process configurations and develop a design methodology for full-scale applications. The first year of the program included pilot-scale tests to evaluate performances of two bituminous coals in basic reburning and modeling studies designed to identify parameters that affect the FFR performance and to evaluate efficiency of coal pyrolysis products as a reburning fuel. Tests were performed in a 300 kW Boiler Simulator Facility to characterize bituminous coals as reburning fuels. Tests showed that NO{sub x} reduction in basic coal reburning depends on process conditions, initial NO{sub x} and coal type. Up to 60% NO{sub x} reduction was achieved at optimized conditions. Modeling activities during first year concentrated on the development of coal reburning model and on the prediction of NO{sub x} reduction in reburning by coal gasification products. Modeling predicted that

Developing new technology of coal coking

Energy Technology Data Exchange (ETDEWEB)

Erkin, L.I.; Nefedov, P.Ya.

1981-03-01

This paper characterizes types of coke (grain size, compression strength, abrasion, porosity) used by: blast furnaces, shaft furnaces, ferroalloys and phosphorus production, and ore agglomeration. Development of formed metallurgical coke production on the basis of technologies worked out by the Eastern Research Scientific Institute for Coal Chemistry is analyzed. The following phases in the investigations are stressed: optimization of coal blends (increasing proportion of coals with poor caking properties, pressing briquets, carbonization, temperature distribution and temperature control, using heat emitted by hot coke for coal preheating (heat consumption of coking is reduced to 200 kcal/kg). On the basis of technology developed and tested by VUKhIN formed coke consisting of 60% G6 coal and 40% 2SS coal has been produced. Using the coke in blast furnaces increases furnace capacity by 5% and reduces coke consumption in a furnace by 2.6%. It is suggested that wide use of the proposed technology of formed metallurgical coke production in the Kuzbass (using coals with poor caking properties from surface mines) would increase coke production of the region to 50 Mt for a year. technology of producing formed foundry coke from: 80 to 86% anthracites, semianthracites and coals with poor caking properties, 5 to 10% coking coal, and 8% binder is evaluated. Formed foundry coke produced from the blend reduces coke consumption in a foundry by 25 to 30% and increases cast iron temperature by 20 to 50/sup 0/C. Technologies of producing coke for phosphorus industry by continuous coking of coals difficult to coke in vertical coke ovens and production of coke for ore agglomeration are also discussed. (In Russian)

Prediction of China's coal production-environmental pollution based on a hybrid genetic algorithm-system dynamics model

International Nuclear Information System (INIS)

Yu Shiwei; Wei Yiming

2012-01-01

This paper proposes a hybrid model based on genetic algorithm (GA) and system dynamics (SD) for coal production–environmental pollution load in China. GA has been utilized in the optimization of the parameters of the SD model to reduce implementation subjectivity. The chain of “Economic development–coal demand–coal production–environmental pollution load” of China in 2030 was predicted, and scenarios were analyzed. Results show that: (1) GA performs well in optimizing the parameters of the SD model objectively and in simulating the historical data; (2) The demand for coal energy continuously increases, although the coal intensity has actually decreased because of China's persistent economic development. Furthermore, instead of reaching a turning point by 2030, the environmental pollution load continuously increases each year even under the scenario where coal intensity decreased by 20% and investment in pollution abatement increased by 20%; (3) For abating the amount of “three types of wastes”, reducing the coal intensity is more effective than reducing the polluted production per tonne of coal and increasing investment in pollution control. - Highlights: ► We propos a GA-SD model for China's coal production-pollution prediction. ► Genetic algorithm (GA) can objectively and accurately optimize parameters of system dynamics (SD) model. ► Environmental pollution in China is projected to grow in our scenarios by 2030. ► The mechanism of reducing waste production per tonne of coal mining is more effective than others.

Enhancement of Operating Efficiency Of The Central Coal-Preparation Plant of "MMK - UGOL" Ltd. Under Current Conditions

Science.gov (United States)

Basarygin, Maksim

2017-11-01

In this article the subject of enhancement of operating efficiency of the central coal-preparation plant of OOO "MMK-UGOL" is encompassed. Modern trends in the development of technologies and equipment for coal beneficiation are due to the following requirements: improving competitiveness of coal products, improvement of quality of marketable products, reduction of coal production cost, environmental requirements: polluting emission abatement, prepared coal saving, improvement of the effectiveness of resource conservation; complex mechanization and beneficiation process automation. In the article the contemporary problems of raw coal benefication under current conditions of the increased dilution of withdrawable coals with rock fractions are considered. Comparative analysis of efficiency of application of modern concentrating equipment under the conditions of the CCPP of OOO "MMK-UGOL" is carried out on the basis of research works. Particular attention is paid to dehydration of produced coal concentrate with content of volatile agents of more than 35.0% and content of fine-dispersed particles in flotation concentrate of more than 50.0%. Comparative analysis of the coal concentrate dehydration technologies is conducted.

Replacement of Fine Aggregate by using Recyclable Materials in Paving Blocks

Science.gov (United States)

Koganti, Shyam Prakash; Hemanthraja, Kommineni; Sajja, Satish

2017-08-01

Cement concrete paving blocks are precast hard products complete out of cement concrete. The product is made in various sizes and shapes like square, round and rectangular blocks of different dimensions with designs for interlocking of adjacent tiles blocks. Several Research Works have been carried out in the past to study the possibility of utilizing waste materials and industrial byproducts in the manufacturing of paver blocks. Various industrial waste materials like quarry dust, glass powder, ceramic dust and coal dust are used as partial replacement of fine aggregate and assessed the strength parameters and compared the profit percentages after replacement with waste materials. Quarry dust can be replaced by 20% and beyond that the difference in strength is not much higher but considering cost we can replace upto 40% so that we can get a profit of almost 10%. Similarly we can replace glass powder and ceramic dust by 20% only beyond that there is decrement in strength and even with 20% replacement we can get 1.34 % and 2.42% of profit. Coal dust is not suitable for alternative material as fine aggregate as it reduces the strength.

Achievements and research programs of the Institute for Chemical Coal Processing in the field of conventional coking

Energy Technology Data Exchange (ETDEWEB)

Cieslar, R.; Kaziszyn, I.; Zawistowksi, J.

1986-11-01

This paper describes research programs of the Institute for Chemical Coal Processing in Zabrze on black coal coking and coke use in metallurgy from 1955 to 1990. In 1955-1970 the programs concentrated on coal mixture composition (selective crushing), optimization of coking conditions, mechanical coke treatment. In 1971-1980 research concentrated on coal preparation prior to coking and new coking systems for the Katowice steel plant (heat treatments, design of large coke ovens). The following research programs were implemented in 1981-1985: partial coal charge briquetting, production of foundry coke, coal charge preheating, production of blast furnace coke from black coal from Dobiensko, reducing coke consumption of blast furnaces. In 1986-1990 the Institute will concentrate on the following research programs: coal preparation schemes and coking schemes for coking low-quality weakly caking coals, optimization of coke oven design (e.g. use of packed charge), reducing coke consumption in metallurgy and heating systems, reducing air pollution from coking.

Nanometre-sized pores in coal: Variations between coal basins and coal origin

Science.gov (United States)

Sakurovs, Richard; Koval, Lukas; Grigore, Mihaela; Sokolava, Anna; Ruppert, Leslie F.; Melnichenko, Yuri B.

2018-01-01

We have used small angle neutron scattering (SANS) to investigate the differences in methane and hexane penetration in pores in bituminous coal samples from the U.S., Canada, South Africa, and China, and maceral concentrates from Australian coals. This work is an extension of previous work that showed consistent differences between the extent of penetration by methane into 10–20 nm size pores in inertinite in bituminous coals from Australia, North America and Poland.In this study we have confirmed that there are differences in the response of inertinite to methane and hexane penetration in coals sourced from different coal basins. Inertinite in Permian Australian coals generally has relatively high numbers of pores in the 2.5–250 nm size range and the pores are highly penetrable by methane and hexane; coals sourced from Western Canada had similar penetrability to these Australian coals. However, the penetrability of methane and hexane into inertinite from the Australian Illawarra Coal Measures (also Permian) is substantially less than that of the other Australian coals; there are about 80% fewer 12 nm pores in Illawarra inertinite compared to the other Australian coals examined. The inertinite in coals sourced from South Africa and China had accessibility intermediate between the Illawarra coals and the other Australian coals.The extent of hexane penetration was 10–20% less than CD4 penetration into the same coal and this difference was most pronounced in the 5–50 nm pore size range. Hexane and methane penetrability into the coals showed similar trends with inertinite content.The observed variations in inertinite porosity between coals from different coal regions and coal basins may explain why previous studies differ in their observations of the relationships between gas sorption behavior, permeability, porosity, and maceral composition. These variations are not simply a demarcation between Northern and Southern Hemisphere coals.

Meditation on the construction of exemplar plant for briquetted coal gasification

Energy Technology Data Exchange (ETDEWEB)

Zhou Kuiyi [China National Coal Industry Import and Export Corporation, Beijing (China)

1997-12-31

China uses a considerable amount of anthracite, but the fines from anthracite mining are not sufficiently used. This project involved the construction of a plant for the manufacture of anthracite briquettes under high pressure, for use in gasification plants. The characteristics of the coals used and the types of briquette formed are described. 2 tabs.

The partition behavior and the chemical speciation of selected trace elements in a typical coal sample during pyrolysis / Tivo Bafana Hlatshwayo

OpenAIRE

Hlatshwayo, Tivo Bafana

2008-01-01

Sasol is by far the world's leading company in upgrading of low-grade coal into high value chemicals and fuels. Such plants also utilise fine particles or pulverised coal in the combustion process to generate steam and electricity for their processes. Certain trace elements released from coal during utilisation may be of environmental concern. From the literature findings it appears that the elements of interest are mercury, arsenic and selenium due to their potential health hazard and as...

Influence of high-energy impact on the physical and technical characteristics of coal fuels

Science.gov (United States)

Mal'tsev, L. I.; Belogurova, T. P.; Kravchenko, I. V.

2017-08-01

Currently, in the world's large-scale coal-fired power industry, the combustion of pulverized coal is the most widely spread technology of combusting the coals. In recent years, the micropulverization technology for preparation and combustion of the coal has been developed in this field. As applied to the small-scale power industry, the method of combusting the coal in the form of a coal-water slurry has been explored for years. Fine coal powders are produced and used in the pulverized-coal gasification. Therefore, the coal preparation methods that involve high-dispersion disintegration of coals attract the greatest interest. The article deals with the problems of high-energy impact on the coal during the preparation of pulverized-coal fuels and coal-water slurries, in particular, during the milling of the coal in ball drum mills and the subsequent regrinding in disintegrators or the cavitation treatment of the coal-water slurries. The investigations were conducted using samples of anthracite and lignite from Belovskii open-pit mine (Kuznetsk Basin). It is shown that both the disintegration and the cavitation treatment are efficient methods for controlling the fuel characteristics. Both methods allow increasing the degree of dispersion of the coal. The content of the small-sized particles reground by cavitation considerably exceeds the similar figure obtained using the disintegrator. The specific surface area of the coal is increased by both cavitation and disintegration with the cavitation treatment producing a considerably greater effect. Being subjected to the cavitation treatment, most coal particles assume the form of a split characterized by the thermodynamically nonequilibrium state. Under external action, in particular, of temperature, the morphological structure of such pulverized materials changes faster and, consequently, the combustion of the treated coal should occur more efficiently. The obtained results are explained from the physical point of view.

Enterprise investment, local government intervention and coal overcapacity: The case of China

International Nuclear Information System (INIS)

Zhang, Yanfang; Zhang, Ming; Liu, Yue; Nie, Rui

2017-01-01

Long-term management of China's coal overcapacity depends on the targeted policy guidance on industry production capacity expansion in the overcapacity formation process. In this study, coal enterprise and local government are treated as game participants, and a three-stage dynamic game model has been developed to depict the boosting effect of the game behavior of coal enterprise's and local government's capacity investments in different markets of supply and demand. The results are shown in the following: (1) local government has been the 'behind-the-scenes' operator of over-investment and redundant construction, and its excessive interventions in coal industry investment have been the primary cause of overcapacity formation; (2) when the market is in short supply, coal enterprise's optimal behavior is to continuously increase the rate of investment growth until it reaches the threshold to obtain the maximum excess profits, ultimately leading to overinvestment in the industry; and (3) the key factors affecting the game abilities of coal enterprise and local government are the market's self-regulation and the central government's supervision intensity. Although the Chinese government, a highly vertically oriented bureaucratic structure, is implementing a mandatory de-capacity policy to alleviate the intensity of excessive coal capacity, it is not a long-term regularization on the supply-side reform. - Highlights: • The formation of China's coal overcapacity is studied from capacity investors. • A three-stage game is developed to depict the boosting effect of coal overcapacity. • Local government has been the 'behind-the-scenes' operators of coal overcapacity. • Coal enterprise's optimal strategy is reaching an investment-max with undersupply. • Chinese government should rely more on market mechanisms instead of intervention.

Off-line image analysis for froth flotation of coal

Energy Technology Data Exchange (ETDEWEB)

Citir, C.; Aktas, Z.; Berber, R. [Ankara University, Ankara (Turkey). Faculty of Engineering

2004-05-15

Froth flotation is an effective process for separating sulphur and fine minerals from coal. Such pre-cleaning of coal is necessary in order to reduce the environmental and operational problems in power plants. The separation depends very much on particle surface properties, and the selectivity can be improved by addition of a reagent. Image analysis can be used to determine the amount of reagent, by using the relation between surface properties and froth bubble sizes. This work reports some improvements in the efficiency of the image analysis, and in determination of bubble diameter distribution towards developing froth-based flotation models. Ultimate benefit of the technique would allow a pre-determined reagent addition profile to be identified for controlling the separation process.

Studies on coal flotation in flotation column using statistical technique

Energy Technology Data Exchange (ETDEWEB)

M.S. Jena; S.K. Biswal; K.K. Rao; P.S.R. Reddy [Institute of Minerals & Materials Technology (IMMT), Orissa (India)

2009-07-01

Flotation of Indian high ash coking coal fines to obtain clean coal has been reported earlier by many authors. Here an attempt has been made to systematically analyse factors influencing the flotation process using statistical design of experiments technique. Studies carried out in a 100 mm diameter column using factorial design to establish weightage of factors such as feed rate, air rate and collector dosage indicated that all three parameters have equal influence on the flotation process. Subsequently RSM-CCD design was used to obtain best result and it is observed that 94% combustibles can be recovered with 82.5% weight recovery at 21.4% ash from a feed containing 31.3% ash content.

Comprehensive assessment of toxic emissions from coal-fired power plants

International Nuclear Information System (INIS)

Brown, T.D.; Schmidt, C.E.; Radziwon, A.S.

1991-01-01

The Pittsburgh Energy Technology Center (PETC) of the US Department of Energy (DOE) has two current investigations, initiated before passage of the Clean Air Act Amendment (CAAA), that will determine the air toxic emissions from coal-fired electric utilities. DOE has contracted with Battelle Memorial Institute and Radian corporation to conduct studies focusing on the potential air toxics, both organic and inorganic, associated with different size fractions of fine particulate matter emitted from power plant stacks. Table 2 indicates the selected analytes to be investigated during these studies. PETC is also developing guidance on the monitoring of Hazardous Air Pollutants (HAPS) to be incorporated in the Environmental Monitoring plans for the demonstration projects in its Clean Coal Technology Program

Lab-scale investigation of Middle-Bosnia coals to achieve high-efficient and clean combustion technology

Directory of Open Access Journals (Sweden)

Smajevic Izet

2014-01-01

Full Text Available This paper describes full lab-scale investigation of Middle-Bosnia coals launched to support selection an appropriate combustion technology and to support optimization of the boiler design. Tested mix of Middle-Bosnia brown coals is projected coal for new co-generation power plant Kakanj Unit 8 (300-450 MWe, EP B&H electricity utility. The basic coal blend consisting of the coals Kakanj: Breza: Zenica at approximate mass ratio of 70:20:10 is low grade brown coal with very high percentage of ash - over 40%. Testing that coal in circulated fluidized bed combustion technique, performed at Ruhr-University Bohum and Doosan Lentjes GmbH, has shown its inconveniency for fluidized bed combustion technology, primarily due to the agglomeration problems. Tests of these coals in PFC (pulverized fuel combustion technology have been performed in referent laboratory at Faculty of Mechanical Engineering of Sarajevo University, on a lab-scale PFC furnace, to provide reliable data for further analysis. The PFC tests results are fitted well with previously obtained results of the burning similar Bosnian coal blends in the PFC dry bottom furnace technique. Combination of the coals shares, the process temperature and the air combustion distribution for the lowest NOx and SO2 emissions was found in this work, provided that combustion efficiency and CO emissions are within very strict criteria, considering specific settlement of lab-scale furnace. Sustainability assessment based on calculation economic and environmental indicators, in combination with Low Cost Planning method, is used for optimization the power plant design. The results of the full lab-scale investigation will help in selection optimal Boiler design, to achieve sustainable energy system with high-efficient and clean combustion technology applied for given coals.

Optimal Level of Woody Biomass Co-Firing with Coal Power Plant Considering Advanced Feedstock Logistics System

Directory of Open Access Journals (Sweden)

Sangpil Ko

2018-05-01

Full Text Available Co-firing from woody biomass feedstock is one of the alternatives toward increased use of renewable feedstock in existing coal power plants. However, the economic level of co-firing at a particular power plant depends on several site-specific factors. Torrefaction has been identified recently as a promising biomass pretreatment option to lead to reduction of the feedstock delivered cost, and thus facilitate an increase in the co-firing ratio. In this study, a mixed integer linear program (MILP is developed to integrate supply chain of co-firing and torrefaction process and find the optimal level of biomass co-firing in terms of minimized transportation and logistics costs, with or without tax credits. A case study of 26 existing coal power plants in three Great Lakes States of the US is used to test the model. The results reveal that torrefaction process can lead to higher levels of co-firing, but without the tax credit, the effect is limited to the low capacity of power plants. The sensitivity analysis shows that co-firing ratio has higher sensitivity to variation in capital and operation costs of torrefaction than to the variation in the transportation and feedstock purchase costs.

Anastomosing river deposits: palaeoenvironmental control on coal quality and distribution, Northern Karoo Basin

Energy Technology Data Exchange (ETDEWEB)

Cairncross, B

1980-01-01

Borehole data from an area close to the northern margin of the Karoo Basin 110 m thick coal reveal a bearing succession of the Vryheid Formation overlying Dwyka tillite. The lowermost sediments reflect processes of deglaciation with a complex array of glaciolacustrine, glaciofluvial and alluvial-outwash fan deposits. Above this paraglacial milieu, tundra-type peat bogs developed in inactive areas and account for the two thick basal coal seams (No. 1 and 2 seams). During accumulation of peat which was later to form the extensive No. 2 coal seam, active clastic sedimentation was confined to laterally restricted river channels which incised into the underlying peat. Lateral migration was inhibited by vegetation stabilized river banks and channel deposits are characterized by vertically accreted upward-fining cycles. Channel fill consists of coarse-grinder bedload sediment deposited in anastomosing streams. Flood episodes are marked by widespread, but thin (< 1 m), shale zones that intercalate with the channel sandstones. Both sandstone and shale units are completely enveloped by No. 2 coal seams. This clastic parting influences No. 2 coal seam distribution and ash content. 23 references

Optimized Solvent for Energy-Efficient, Environmentally-Friendly Capture of CO{sub 2} at Coal-Fired Power Plants

Energy Technology Data Exchange (ETDEWEB)

Farthing, G. A.; Rimpf, L. M.

2014-04-30

The overall goal of this project, as originally proposed, was to optimize the formulation of a novel solvent as a critical enabler for the cost-effective, energy-efficient, environmentally-friendly capture of CO{sub 2} at coal-fired utility plants. Aqueous blends of concentrated piperazine (PZ) with other compounds had been shown to exhibit high rates of CO{sub 2} absorption, low regeneration energy, and other desirable performance characteristics during an earlier 5-year development program conducted by B&W. The specific objective of this project was to identify PZ-based solvent formulations that globally optimize the performance of coal-fired power plants equipped with CO{sub 2} scrubbing systems. While previous solvent development studies have tended to focus on energy consumption and absorber size, important issues to be sure, the current work seeks to explore, understand, and optimize solvent formulation across the full gamut of issues related to commercial application of the technology: capital and operating costs, operability, reliability, environmental, health and safety (EH&S), etc. Work on the project was intended to be performed under four budget periods. The objective of the work in the first budget period has been to identify several candidate formulations of a concentrated PZ-based solvent for detailed characterization and evaluation. Work in the second budget period would generate reliable and comprehensive property and performance data for the identified formulations. Work in the third budget period would quantify the expected performance of the selected formulations in a commercial CO{sub 2} scrubbing process. Finally, work in the fourth budget period would provide a final technology feasibility study and a preliminary technology EH&S assessment. Due to other business priorities, however, B&W has requested that this project be terminated at the end of the first budget period. This document therefore serves as the final report for this project. It

Next Generation Pressurized Oxy-Coal Combustion: High Efficiency and No Flue Gas Recirculation

Energy Technology Data Exchange (ETDEWEB)

Rue, David

2013-09-30

The Gas Technology Institute (GTI) has developed a pressurized oxy-coal fired molten bed boiler (MBB) concept, in which coal and oxygen are fired directly into a bed of molten coal slag through burners located on the bottom of the boiler and fired upward. Circulation of heat by the molten slag eliminates the need for a flue gas recirculation loop and provides excellent heat transfer to steam tubes in the boiler walls. Advantages of the MBB technology over other boilers include higher efficiency (from eliminating flue gas recirculation), a smaller and less expensive boiler, modular design leading to direct scalability, decreased fines carryover and handling costs, smaller exhaust duct size, and smaller emissions control equipment sizes. The objective of this project was to conduct techno-economic analyses and an engineering design of the MBB project and to support this work with thermodynamic analyses and oxy-coal burner testing. Techno-economic analyses of GTI’s pressurized oxy-coal fired MBB technology found that the overall plant with compressed CO2 has an efficiency of 31.6%. This is a significant increase over calculated 29.2% efficiency of first generation oxy-coal plants. Cost of electricity (COE) for the pressurized MBB supercritical steam power plant with CO2 capture and compression was calculated to be 134% of the COE for an air-coal supercritical steam power plant with no CO2 capture. This compares positively with a calculated COE for first generation oxy-coal supercritical steam power plants with CO2 capture and compression of 164%. The COE for the MBB power plant is found to meet the U.S. Department of Energy (DOE) target of 135%, before any plant optimization. The MBB power plant was also determined to be simpler than other oxy-coal power plants with a 17% lower capital cost. No other known combustion technology can produce higher efficiencies or lower COE when CO2 capture and compression are included. A thermodynamic enthalpy and exergy analysis

Optimal Design of Experiments by Combining Coarse and Fine Measurements

Science.gov (United States)

Lee, Alpha A.; Brenner, Michael P.; Colwell, Lucy J.

2017-11-01

In many contexts, it is extremely costly to perform enough high-quality experimental measurements to accurately parametrize a predictive quantitative model. However, it is often much easier to carry out large numbers of experiments that indicate whether each sample is above or below a given threshold. Can many such categorical or "coarse" measurements be combined with a much smaller number of high-resolution or "fine" measurements to yield accurate models? Here, we demonstrate an intuitive strategy, inspired by statistical physics, wherein the coarse measurements are used to identify the salient features of the data, while the fine measurements determine the relative importance of these features. A linear model is inferred from the fine measurements, augmented by a quadratic term that captures the correlation structure of the coarse data. We illustrate our strategy by considering the problems of predicting the antimalarial potency and aqueous solubility of small organic molecules from their 2D molecular structure.

Pillar size optimization design of isolated island panel gob-side entry driving in deep inclined coal seam—case study of Pingmei No. 6 coal seam

Science.gov (United States)

Zhang, Shuai; Wang, Xufeng; Fan, Gangwei; Zhang, Dongsheng; Jianbin, Cui

2018-06-01

There is a perception that deep roadways are difficult to maintain. To reverse this and to improve the recovery rate of coal resources, gob-side entry driving is widely used in coal mines, especially deep-mining coal mines, in China. Determination of the reasonable pillar size through in situ observation and experimentation plays a vital role for roadway maintenance. Based on the geological conditions of Pingmei No.6 coal seam, a theoretical analysis, numerical simulation, and industrial experiments are carried out to calculate the reasonable width of chain pillars, analyze the lateral support stress distribution law near the gob side, investigate the relationship between the coal pillar stress distribution, roadway surrounding rock stress distribution, roadway surrounding rock deformation and the coal pillar width. The results indicate that 5 m wide coal pillars can ensure that the chain pillars are at a lower stress level and the deformation of roadway surrounding rock is in a more reasonable range. Industrial experiments show that when the chain pillar width is 5 m, the deformation of roadway surrounding rock can meet the requirements of working face safe production. The numerical results agreed well with field measurement and observations, and the industrial experiments results further validated the results of the numerical simulation.

Source apportionment of fine organic aerosols in Beijing

Directory of Open Access Journals (Sweden)

S. Guo

2009-11-01

Full Text Available Fine particles (PM_2.5, i.e., particles with an aerodynamic diameter of ≤2.5 μm were collected from the air in August 2005, August–September 2006, and January–February 2007, in Beijing, China. The chemical compositions of particulate organic matter in the ambient samples were quantified by gas chromatography/mass spectrometry. The dominant compounds identified in summertime were n-alkanoic acids, followed by dicarboxylic acids and sugars, while sugars became the most abundant species in winter, followed by polycyclic aromatic hydrocarbons, n-alkanes, and n-alkanoic acids. The contributions of seven emission sources (i.e., gasoline/diesel vehicles, coal burning, wood/straw burning, cooking, and vegetative detritus to particulate organic matter in PM_2.5 were estimated using a chemical mass balance receptor model. The model results present the seasonal trends of source contributions to organic aerosols. Biomass burning (straw and wood had the highest contribution in winter, followed by coal burning, vehicle exhaust, and cooking. The contribution of cooking was the highest in summer, followed by vehicle exhaust and biomass burning, while coal smoke showed only a minor contribution to ambient organic carbon.

Effectiveness of underground coal extraction. Effektivnost' podzemnoy dobychi uglya

Energy Technology Data Exchange (ETDEWEB)

Pirskiy, A A

1982-01-01

This book examines the possibility of improving the efficiency of underground coal extraction based on the solution to the scientific-technical problem of monitoring and controlling concentration and intensifying mining operations. The problem has been resolved as applied to conditions of working coal fields of the Lvov-Volynskiy basin, West Donbass and other regions which are similar in relation to mining-geological conditions. The main conclusions and recommendations consist of the following: synthesized concept ''concentration of mining operations'' is determined by regulation and concentration, intensification of mining operations by using progressive technology, mechanization and organization of production in order to increase extraction, improve productivity of labor and reduce the net cost of coal. The structure of concentration of mining operations is based on the synthesis of natural, technical and organizational conditions for working coal seams. The problem of monitoring and control of the concentration of mining operations was realized by using the systems method based on the laws of development, principles of comprehensive evaluation and optimization of the level of concentration based on economic-mathematical modeling. The use of the systems approach guarantees a comprehensive solution to the problem. In definite periods of development of the coal industry, between the organizational-technical potentialities, natural conditions and trends determined in the sector for the change in the level of mining operation concentration, disproportions develop. The level of work concentration goes beyond the limits of optimal values, and the effectiveness of coal extraction is reduced. In order to predict and eliminate this phenomenon, it is recommended that the level of mining concentration be controlled.

EXPERIMENTS AND COMPUTATIONAL MODELING OF PULVERIZED-COAL IGNITION; FINAL

International Nuclear Information System (INIS)

Samuel Owusu-Ofori; John C. Chen

1999-01-01

Under typical conditions of pulverized-coal combustion, which is characterized by fine particles heated at very high rates, there is currently a lack of certainty regarding the ignition mechanism of bituminous and lower rank coals as well as the ignition rate of reaction. furthermore, there have been no previous studies aimed at examining these factors under various experimental conditions, such as particle size, oxygen concentration, and heating rate. Finally, there is a need to improve current mathematical models of ignition to realistically and accurately depict the particle-to-particle variations that exist within a coal sample. Such a model is needed to extract useful reaction parameters from ignition studies, and to interpret ignition data in a more meaningful way. The authors propose to examine fundamental aspects of coal ignition through (1) experiments to determine the ignition temperature of various coals by direct measurement, and (2) modeling of the ignition process to derive rate constants and to provide a more insightful interpretation of data from ignition experiments. The authors propose to use a novel laser-based ignition experiment to achieve their first objective. Laser-ignition experiments offer the distinct advantage of easy optical access to the particles because of the absence of a furnace or radiating walls, and thus permit direct observation and particle temperature measurement. The ignition temperature of different coals under various experimental conditions can therefore be easily determined by direct measurement using two-color pyrometry. The ignition rate-constants, when the ignition occurs heterogeneously, and the particle heating rates will both be determined from analyses based on these measurements

Production of Schwarzmoeller briquets from weakly caking black coal and iron ore

Energy Technology Data Exchange (ETDEWEB)

Naundorf, W.

1986-01-01

Laboratory production is explained of coal and iron ore briquets suitable for metallurgy, using type 33 weakly caking black coal, iron ore concentrates from 3 Soviet mines and sulfite lye as binder. Coal and ore were finely ground to 0.3/0.0 mm grain size, briquetted at high pressure of 150 MPa and at 80 C temperature. The sulfite lye binder content ranged from 4 to 10% in the briquet mixture. Briquets were thermally treated up to 1000 C; the resulting coke lumps (Schwarzmoeller briquets) were analyzed for compression and abrasion strength. Detailed graphs of briquet and coke lump quality parameters are provided. The study shows that high quality metallurgical coke lumps are obtained by briquetting mixtures of black coal and iron ore in a mixture of about 70:30 with 4 to 9% addition of sulfite binder. Compression strength of coke lumps exceeded 35 MPa. The minimum black coal-iron ore mass relation for producing metallurgical coke lumps was 30:70 using 2 types of iron ore concentrates. The influence of adding limestone to the briquetting mixture and of coking conditions resembling the horizontal chamber oven process is also investigated. 5 references.

The use of mechanically activated micronized coal in thermal power engineering

Directory of Open Access Journals (Sweden)

Burdukov Anatoliy P.

2016-01-01

Full Text Available Coal is one of the main energy resources and development of new promising technologies on its basis is certainly topical. This article discusses the use of new technology of gas and fuel oil replacement by mechanically activated micronized coal in power engineering: ignition and stabilization of pulverized coal flame combustion, as well as gasification of micronized coal in the flow. The new technology coal combustion with two stages of grinding is suggested. Optimization of the scheme of two-stage combustion is calculated. The first experimental data on the combustion process are obtained. The first demonstration tests on gas and heavy oil replacement by micronized coal during boiler ignition were carried out in the real power boiler with the capacity of 320 tons of steam per hour.

Production and Optimization of Direct Coal Liquefaction derived Low Carbon-Footprint Transportation Fuels

Energy Technology Data Exchange (ETDEWEB)

Steven Markovich

2010-06-30

This report summarizes works conducted under DOE Contract No. DE-FC26-05NT42448. The work scope was divided into two categories - (a) experimental program to pretreat and refine a coal derived syncrude sample to meet transportation fuels requirements; (b) system analysis of a commercial scale direct coal liquefaction facility. The coal syncrude was derived from a bituminous coal by Headwaters CTL, while the refining study was carried out under a subcontract to Axens North America. The system analysis included H{sub 2} production cost via six different options, conceptual process design, utilities requirements, CO{sub 2} emission and overall plant economy. As part of the system analysis, impact of various H{sub 2} production options was evaluated. For consistence the comparison was carried out using the DOE H2A model. However, assumptions in the model were updated using Headwaters database. Results of Tier 2 jet fuel specifications evaluation by the Fuels & Energy Branch, US Air Force Research Laboratory (AFRL/RZPF) located at Wright Patterson Air Force Base (Ohio) are also discussed in this report.

Modeling the international competitiveness of Botswana's coal

Science.gov (United States)

Fichani, Khaulani

Botswana has vast proven deposits of steam coal, which for a long time it has wanted to develop but without much success. The main objectives of this study are: (1) to analyze the time schedule of coal exports likely to be forthcoming from Botswana and the land routes for these exports; (2) to determine the competitiveness of Botswana's coal in the world steam coal markets and (3) to make recommendations on the appropriate policy for the exploitation of this coal. To accomplish these objectives, we construct a model of the seaborne steam coal trade consisting of exporters and importers with a substantial share in this trade. We econometrically estimate the long run marginal cost functions for net exporters and employ these to construct a spatial and dynamic model of the world steam coal trade with elastic supply and inelastic demand. This model is applied to simulate Botswana's competitiveness in this trade over the period 1995 to 2010 from a 1990 base year with a decision criterion that minimizes the sum of discounted capital costs of mine development, variable supply costs, rail and maritime transportation costs. Finally, we employ the model to forecast the likely optimal size of mine, timing of production capacity and choice of export port for Botswana's coal for the years 2005 and 2010. The base year for the forecast is 2000. The simulation results indicate that Botswana's coal would have been competitive in the steam coal markets of Western Europe and Asia. The forecast results indicate that Botswana's coal would also be competitive in these markets in the future. These results are least sensitive to changes in rail transportation and variable supply costs but are sensitive to capital costs for mine development.

Coal geopolitics

International Nuclear Information System (INIS)

Giraud, P.N.; Suissa, A.; Coiffard, J.; Cretin, D.

1991-01-01

This book divided into seven chapters, describes coal economic cycle. Chapter one: coals definition; the principle characteristics and properties (origin, calorific power, international classification...) Chapter two: the international coal cycle: coal mining, exploration, coal reserves estimation, coal handling coal industry and environmental impacts. Chapter three: the world coal reserves. Chapter four: the consumptions, productions and trade. Chapter five: the international coal market (exporting mining companies; importing companies; distributors and spot market operators) chapter six: the international coal trade chapter seven: the coal price formation. 234 refs.; 94 figs. and tabs [fr

Hazards from radioactivity of fly ash of Greek coal power plants (CPP)

International Nuclear Information System (INIS)

Papastefanou, C.; Charalambous, C.

1980-01-01

Fly ash and fine dispersion releases by coal combustion in Greek coal power plants are radioactive. Concentrations in the fly ash up to 20 pCi/g and 10 pCi/g were measured for 238 U and 226 Ra respectively (not in secular equilibrium). The radioactivity of fly ash deduces risks in two ways: a) from the escaping fly ash in particulate form or fine dispersion and b) from using fly ash as substitute for cement in concrete. In a room of dimensions 10 x 10x4 m 3 the concentration of Radon in the air will be about 10 -9 μCi/cm 3 . For the above estimation a concrete porosity of 5% and a wall thickness of 20 cm was used. The estimated concentration of Radon was about two orders of magnitude lower than that of the MPC of Radon in the air, which is about 10 -9 μCi/cm 3 . It is pointed out that if a 25% porosity were used, the Radon concentration will be an order of magnitude higher. (U.K.)

Mercury and halogens in coal: Chapter 2

Science.gov (United States)

Kolker, Allan; Quick, Jeffrey C.; Granite, Evan J.; Pennline, Henry W.; Senior, Constance L.

2014-01-01

Apart from mercury itself, coal rank and halogen content are among the most important factors inherent in coal that determine the proportion of mercury captured by conventional controls during coal combustion. This chapter reviews how mercury in coal occurs, gives available concentration data for mercury in U.S. and international commercial coals, and provides an overview of the natural variation in halogens that influence mercury capture. Three databases, the U.S. Geological Survey coal quality (USGS COALQUAL) database for in-ground coals, and the 1999 and 2010 U.S. Environmental Protection Agency (EPA) Information Collection Request (ICR) databases for coals delivered to power stations, provide extensive results for mercury and other parameters that are compared in this chapter. In addition to the United States, detailed characterization of mercury is available on a nationwide basis for China, whose mean values in recent compilations are very similar to the United States in-ground mean of 0.17 ppm mercury. Available data for the next five largest producers (India, Australia, South Africa, the Russian Federation, and Indonesia) are more limited and with the possible exceptions of Australia and the Russian Federation, do not allow nationwide means for mercury in coal to be calculated. Chlorine in coal varies as a function of rank and correspondingly, depth of burial. As discussed elsewhere in this volume, on a proportional basis, bromine is more effective than chlorine in promoting mercury oxidation in flue gas and capture by conventional controls. The ratio of bromine to chlorine in coal is indicative of the proportion of halogens present in formation waters within a coal basin. This ratio is relatively constant except in coals that have interacted with deep-basin brines that have reached halite saturation, enriching residual fluids in bromine. Results presented here help optimize mercury capture by conventional controls and provide a starting point for

Prediction of oxy-coal combustion through an optimized weighted sum of gray gases model

International Nuclear Information System (INIS)

Kangwanpongpan, Tanin; Corrêa da Silva, Rodrigo; Krautz, Hans Joachim

2012-01-01

Oxy-fuel combustion is considered as one of promising options for carbon dioxide capture in future coal power plants. Currently models available in CFD codes fail to predict accurately the radiative heat transfer in oxy-fuel cases due to higher pressure of carbon dioxide and water vapor. This paper concerns numerical investigation applying three band formulations aiming an accurate prediction of radiative properties. The radiative heat transfer is calculated by discrete ordinate method coupled with a weighted sum of gray gases model. The first case relates to the domain-based approach using air-fired parameters. In the last two cases, the optimized parameters of 3 and 4 gray gases fitted to oxy-fired conditions are implemented through a non-gray gases approach. Results applying these set of parameters are evaluated through a comparison with experimental data. Discrepancies between the predicted and measured velocity and O 2 concentration are found mainly close to the burner due to shortcomings of the turbulence model and inaccurate thermochemical closure. The gas flame temperatures are better predicted by the optimized parameters for oxy-fuel conditions, which are considerably lower than the values calculated by the air-fired parameters. Similar trends are observed when the radiative heat fluxes at the lateral wall are compared.

Assessment of Comprehensive Effects and Optimization of a Circular Economy System of Coal Power and Cement in Kongtong District, Pingliang City, Gansu Province, China

Directory of Open Access Journals (Sweden)

Suocheng Dong

2017-05-01

Full Text Available The idea of a circular economy (CE, which differs from traditional linear economy with a high consumption of natural resources and pollution, has captured much interest and attention. This paper uses a CE system of coal power and cement in Kongtong District, Pingliang City, Gansu Province, China as a case study to analyze the comprehensive effects of CE paradigm. Our simulation results, based on system dynamics (SD modeling, infer that the transformation of manufacturing towards a CE system can prominently help coal power and cement enterprises reduce waste emission and increase economic profits. Through solid waste exchanges, a power plant can achieve over RMB 80 million of additional revenue per year at the highest level. CE also contributes to the reduction of regional pollution, saves mineral resources, and improves the atmospheric environment, an accumulated total of 14.11 million t of natural gypsum and 22.67 million t of coal can be saved. This sets a promising example for coal power and cement plants worldwide. Effective regulatory measures and further optimization towards a circular economy system are essential in maintaining the stable development of a CE system due to the risk of surplus production of upstream industries and other defects.

Economic Decision-Making for Coal Power Flexibility Retrofitting and Compensation in China

Directory of Open Access Journals (Sweden)

Chunning Na

2018-01-01

Full Text Available In China, in order to integrate more renewable energy into the power grid, coal power flexibility retrofitting is imperative. This paper elaborates a generic method for estimating the flexibility potential from the rapid ramp rate and peak shaving operation using nonlinear programming, and defines three flexibility elastic coefficients to quantify the retrofitted targets. The optimized range of the retrofitted targets determined by the flexibility elastic coefficients have a reference significance on coal power flexibility retrofitting. Then, in order to enable economic decisions for coal power flexibility retrofitting, we address a profit maximizing issue regarding optimization decisions for coal power flexibility retrofitting under an assumption of perfect competition, further analyzing the characteristic roots of marginal cost equal to marginal revenue. The rationality of current compensation standards for peak shaving in China can also be judged in the analysis. The case study results show that economic decision-making depends on the compensation standard and the peak shaving depth and time. At a certain peak shaving depth and time, with rational compensation standard power plants are willing to carry out coal power flexibility retrofitting. The current compensation standard in Northeast China is high enough to carry out coal power flexibility retrofitting. These research conclusions have theoretical significance for China’s peak shaving compensation standards formulation.

Coal and potash flotation enhancement using a clay binder

Energy Technology Data Exchange (ETDEWEB)

Tao, D.; Chen, G.L.; Zhou, X.H.; Zhao, C.; Fan, M.M.; Aron, M.; Wright, J. [University of Kentucky, Lexington, KY (United States)

2007-07-15

The adverse effects of clay particles on coal and mineral processing operations such as gravity separation, flotation, filtration and thickening are well known in the mining industry. In particular, the presence of ultra-fine clay particles deteriorates froth flotation performance, which has been attributed to slime coatings that inhibit bubble attachment and to adsorption of the frother and/or collector by the clay particles. The present study was conducted to evaluate the performance of a clay binding agent developed by Georgia-Pacific Resins, Inc. in enhancing coal and mineral flotation performance. Mechanical flotation tests were carried out using coal and potash samples. Process parameters investigated included slurry solids percentage, impeller rotation speed, binder dosage, etc. Flotation results show that the use of GP reagents significantly enhanced flotation efficiency under different conditions. The required binder dosage and conditioning time were about 0.45 kg/t and 0.5 to 1 minute, respectively. More significant improvements in process performance were observed at higher solids percentage and higher impeller rotation speed.

Ninth annual coal preparation, utilization, and environmental control contractors conference: Proceedings

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

Papers are grouped under the following sessions: compliance technology; high-efficiency preparation; characterization; advanced technologies; alternative fuels; coal utilization; industrial/commercial combustor development; combustion; superclean emission systems; carbon dioxide recovery and reuse; air toxics and fine particulates; air toxics sampling and analysis workshop; and combined poster session. Selected papers have been processed separately for inclusion in the Energy Science and Technology Database.

Multi-objective Optimization of Coal-fired Boiler Combustion Based on NSGA-II

OpenAIRE

Tingfang Yu; Hongzhen Zhu; Chunhua Peng

2013-01-01

NOx emission characteristics and overall heat loss model for a 300MW coal-fired boiler were established by Back Propagation (BP) neural network, by which the the functional relationship between outputs (NOx emissions & overall heat loss of the boiler) and inputs (operational parameters of the boiler) of a coal-fired boiler can be predicted. A number of field test data from a full-scale operating 300MWe boiler were used to train and verify the BP model. The NOx emissions & heat loss pr...

Main characteristics of the radioactive enrichment in ashes produced in coal-fired power stations

International Nuclear Information System (INIS)

Baeza, Antonio; Corbacho, Jose A.; Cancio, David; Robles, Beatriz; Mora, Juan C.

2008-01-01

Under contract with the Spain's 'Nuclear Safety Council', a study is being conducted of the nation's largest nominal output coal-fired power stations. Its purpose is to assess the radiological impact on workers and local populations due to this source of NORM activity. One of the aspects of particular interest is the study of the radioactive enrichment in the combustion wastes relative to the different coals used as fuel (usually local bituminous coal or lignite, or imported coal). These wastes consist of fly ash (mostly fine particles collected in electrostatic precipitators), and bottom ash (larger in size, and collected wet or dry in hoppers below the boilers). In general terms, the enrichment factors measured were between 2 and 18 for the radionuclides 40 K, 226 Ra, 232 Th, and 210 Po. The magnitude of this enrichment factor depended mainly on the ash content of each coal, and hence on the type of coal used as fuel and the specific operation cycle in the different power stations. For the radionuclides 40 K, 226 Ra, and 232 Th, the enrichment was relatively similar in value in the fly and bottom ashes produced by the different types of coal used in the power stations studied. For 210 Po, however, as was expected, the enrichment was much greater in the fly ash than in the bottom ash for each coal analyzed. (author)

Study on Reduction Kinetics of Briquettes of Hematite Fines with Boiler Grade Coal and Coke Dust in Two Different Forms: Intermixing and Multilayered

Science.gov (United States)

Roy, Gopal Ghosh; Sarkar, Bitan Kumar; Chaudhuri, Mahua Ghosh; Mitra, Manoj Kumar; Dey, Rajib

2017-10-01

An attempt has been made to utilise hematite ore fines in the form of briquettes with two different form of mixing i.e. intermixing and multilayered by means of carbothermal reduction along with boiler grade coal and coke dust. The influence of reduction temperature (1323, 1373 and 1423 K) and reduction time (10, 20, 30, 45 and 60 min) has been investigated in detail and the reduced briquettes are characterised by XRD, SEM analyses. The reducibility of intermixing briquettes is found to be higher for multilayered briquettes. In addition, isothermal kinetic study has also been carried out for both intermixing and multilayered briquettes. The activation energy for intermixing briquettes are evaluated to be 125.88 kJ/mol for the initial stage of reaction (CG3 controlled mechanism) and 113.11 kJ/mol for the later part of reaction (D3 controlled mechanism), respectively. In case of multilayered briquettes, the corresponding activation energy is found to be 235.59 kJ/mol for reaction (CG3 controlled mechanism). These results corroborate the observed better reducibility of the intermixing briquettes over multilayered briquettes.

Technical data. Final technical report, November 1980-May 1982. [Proposed WyCoalGas project, Converse County, Wyoming

Energy Technology Data Exchange (ETDEWEB)

None

1982-01-01

This volume includes a description of the railway to transport the coal; possible unbalance in the electrical power supply is considered in detail, as well as communications, signalling, etc. The railway will also be used to transport ashes and sludges for waste disposal. Coal fines in the coal supply will be burned to generate power. A very brief description of the coal gasification plant and its components is accompanied by a printout of the dates final engineering is to be completed. Permit applications are listed and socio-economic factors are discussed. The financing plan is discussed in some detail: basically, a loan guarantee from the Synthetic Fuels Corporation; equity provided by investment tax credit, deferred taxes, AFUDC and the sponsors; price support; and gas purchase agreement (this whole section includes several legal details.). (LTN)

Coal Field Fire Fighting - Practiced methods, strategies and tactics

Science.gov (United States)

Wündrich, T.; Korten, A. A.; Barth, U. H.

2009-04-01

Subsurface coal fires destroy millions of tons of coal each year, have an immense impact to the ecological surrounding and threaten further coal reservoirs. Due to enormous dimensions a coal seam fire can develop, high operational expenses are needed. As part of the Sino-German coal fire research initiative "Innovative technologies for exploration, extinction and monitoring of coal fires in Northern China" the research team of University of Wuppertal (BUW) focuses on fire extinction strategies and tactics as well as aspects of environmental and health safety. Besides the choice and the correct application of different extinction techniques further factors are essential for the successful extinction. Appropriate tactics, well trained and protected personnel and the choice of the best fitting extinguishing agents are necessary for the successful extinction of a coal seam fire. The chosen strategy for an extinction campaign is generally determined by urgency and importance. It may depend on national objectives and concepts of coal conservation, on environmental protection (e.g. commitment to green house gases (GHG) reductions), national funding and resources for fire fighting (e.g. personnel, infrastructure, vehicles, water pipelines); and computer-aided models and simulations of coal fire development from self ignition to extinction. In order to devise an optimal fire fighting strategy, "aims of protection" have to be defined in a first step. These may be: - directly affected coal seams; - neighboring seams and coalfields; - GHG emissions into the atmosphere; - Returns on investments (costs of fire fighting compared to value of saved coal). In a further step, it is imperative to decide whether the budget shall define the results, or the results define the budget; i.e. whether there are fixed objectives for the mission that will dictate the overall budget, or whether the limited resources available shall set the scope within which the best possible results shall be

Electroosmotically enhanced dewatering/deliquoring of fine-particle coal: Final report, January 1--December 31, 1988

Energy Technology Data Exchange (ETDEWEB)

Sami, Sedat [Department of Civil Engineering and Mechanics, Southern Illinois Univ., Carbondale, IL (United States); Davis, Philip K. [Department of Civil Engineering and Mechanics, Southern Illinois Univ., Carbondale, IL (United States); Smith, James G. [Department of Electrical Engineering, Southern Illinois Univ., Carbondale, IL (United States)

1989-03-01

This research is an investigation of the use of electroosmosis to dewater/deliquor ultrafine coal. Post-beneficiation dewatering/deliquoring methods for ultrafine coal are inadequate and generally require subsequent thermal drying. Thermal drying is not only expensive and time consuming, it also does not recover liquids for reuse in beneficiation processes. The degree of difficulty associated with dewatering increases as surface forces become more important than gravimetric forces. Electroosmotic flow has advantages for dewatering because it is much less sensitive to pore size than hydraulic gradient flow for the 1 to 75 ..mu..m ultrafine size range. The first year of this project focused upon preparation of ultrafine coal samples, development of test equipment and test cells, identification of variables affecting electroosmosis, and trial runs. Techniques and procedures not previously used by researchers of electroosmotic dewatering have revealed important information about the dynamics of the electroosmosis process. The identification of the first few millimeters of the cathode region of the cell as the sink for most of the energy input into the process provides the potential for improving efficiency by concentrating the second year effort on intervention in that region. Information gathered about differences in FTIR spectra as a function of location in the dewatering cell will be investigated. Changes in pH with temperature and by the application of electroosmotic current flow will receive attention, as well. 178 refs., 16 figs.

Coal 1992

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

ACR's Coal 1992, the successor to the ACR Coal Marketing Manual, contains a comprehensive set of data on many aspects of the Australian coal industry for several years leading up to 1992. Tables and text give details of coal production and consumption in New South Wales, Queensland and other states. Statistics of the Australian export industry are complemented by those of South Africa, USA, New Zealand, Canada, Indonesia, China, Colombia, Poland and ex-USSR. Also listed are prices of Australian coking and non-coking coal, Australian coal stocks (and those of other major countries), loading port capacities, freight rates and coal quality requirements (analysis of coals by brand and supplier). A listing of Australian coal exporting companies is provided. A description of the spot Coal Screen Dealing System is given. World hard coal imports are listed by country and coal imports by major Asian countries tabulated. A forecast of demand by coal type and country up to the year 2000 is included.

Characterization of Coal Porosity for Naturally Tectonically Stressed Coals in Huaibei Coal Field, China

Science.gov (United States)

Li, Xiaoshi; Hou, Quanlin; Li, Zhuo; Wei, Mingming

2014-01-01

The enrichment of coalbed methane (CBM) and the outburst of gas in a coal mine are closely related to the nanopore structure of coal. The evolutionary characteristics of 12 coal nanopore structures under different natural deformational mechanisms (brittle and ductile deformation) are studied using a scanning electron microscope (SEM) and low-temperature nitrogen adsorption. The results indicate that there are mainly submicropores (2~5 nm) and supermicropores (coal and mesopores (10~100 nm) and micropores (5~10 nm) in brittle deformed coal. The cumulative pore volume (V) and surface area (S) in brittle deformed coal are smaller than those in ductile deformed coal which indicates more adsorption space for gas. The coal with the smaller pores exhibits a large surface area, and coal with the larger pores exhibits a large volume for a given pore volume. We also found that the relationship between S and V turns from a positive correlation to a negative correlation when S > 4 m2/g, with pore sizes coal. The nanopore structure (coal. PMID:25126601

A compact XRF unit for determining total sulphur content in coals

International Nuclear Information System (INIS)

Sumitra, T.; Chankow, N.; Punnachaiya, S.; Srisatit, S.

1994-01-01

A microcomputer based x-ray fluorescence (XRF) unit was developed for off-line determination of total sulphur content in coal samples. The unit consisted of the x-ray exciting/measuring set and the microcomputer with a plug-in interface card. An Fe-55 radioisotope was used as the exciting source while a krypton-filled proportional counter was used to measure x-rays from the samples. The x-ray spectrum was simultaneously displayed on the microcomputer screen. For quantitative determination of sulphur, the intensities of sulphur K x-rays as well as calcium K x-rays and scattered x-rays were taken into account. The unit was tested with finely-ground, dried and compressed lignite, subbituminous and bituminous samples. If was found that for low-calcium coals, the results were in good agreement with those obtained from the standard chemical analysis method within ± 0.2% and within ± 0.5%S for high-calcium coals. 2 refs., 2 tabs., 3 figs

Ultra High Efficiency ESP for Fine Particulate and Air Toxics Control

International Nuclear Information System (INIS)

Srinivasachar, Srivats; Pease, Benjamin R.; Porle, Kjell; Mauritzson, Christer; Haythornthwaite, Sheila

1997-01-01

Nearly ninety percent of U.S. coal-fired utility boilers are equipped with electrostatic precipitators (ESP). Cost effective retrofittable ESP technologies are the only means to accomplish Department of Energy's (DOE) goal of a major reduction in fine particulate and air toxic emissions from coal-fired power plants. Particles in the size range of 0.1 to 5 (micro)m typically escape ESPs. Metals, such as arsenic, cadmium, lead, molybdenum and antimony, concentrate on these particles. This is the main driver for improved fine particulate control. Vapor phase emissions of mercury, selenium and arsenic are also of major concern. Current dry ESPs, which operate at temperatures greater than 280 F, provide little control for vapor phase toxics. The need for inherent improvement to ESPs has to be considered keeping in perspective the current trend towards the use of low sulfur coals. Switching to low sulfur coals is the dominant approach for SO 2 emission reduction in the utility industry. Low sulfur coals generate high resistivity ash, which can cause an undesirable phenomenon called ''back corona.'' Higher particulate emissions occur if there is back corona in the ESP. Results of the pilot-scale testing identified the ''low temperature ESP'' concept to have the biggest impact for the two low sulfur coals investigated. Lowering the flue gas temperature to 220 F provided the maximum impact in terms of decreased emissions. Intermediate operating temperatures (reduction from 340 to 270 F) also gave significant ESP performance improvement. A significant reduction in particulate emissions was also noted when the flue gas humidity was increased (temperature held constant) from the baseline condition for these moderately high resistivity ash coals. Independent control of flue gas humidity and temperature was an important and a notable element in this project. Mercury emissions were also measured as a function of flue gas temperature. Mercury emissions decreased as the flue gas

Pilot plant for hydrogasification of coal with nuclear heat

International Nuclear Information System (INIS)

Falkenhain, G.; Velling, G.

1976-01-01

In the framework of a research and development programme sponsored by the Ministry of Research and Technology of the Federal Republic of Germany, two process variants for hydrogasification of coal by means of nuclear heat have been developed by the Rheinische Braunkohlenwerke AG, Cologne. For testing these process variants a semi-technical pilot plant for gasification of coal under pressure in a fluidized bed was constructed. The pilot plant, in which the gasification of lignite and hard coal is planned, is designed for a throughput of 100kg carbon per hour corresponding to 400kg raw lignite per hour or 150kg hard coal per hour. The plant should provide data on the influence of the most essential process parameters (pressure, temperature, residence time of gas and coal, type and pre-treatment of feed coal) on the performance of gasification and raw gas composition. Different plant components will also be tested. Since the pilot plant will permit testing of both process variants of hydrogasification, it was designed in such a way that it is possible to vary a great number of process parameters. Thus, for instance, the pressure can be chosen in a range up to 100 bar and pure hydrogen or mixtures of hydrogen, carbon monoxide and steam can be applied as gasification agents. The gasifier is an internally insulated fluidized bed reactor with an inner diameter of 200mm and a height of about 8m, to which an internally insulated cyclone for separation of the entrained fines is attached. The raw gas is then cooled down by direct water scrubbing. (author)

Kinetic study of coals gasification into carbon dioxide atmosphere

Directory of Open Access Journals (Sweden)

Korotkikh A.G.

2015-01-01

Full Text Available The solid fuel gasification process was investigated to define chemical reactions rate and activation energy for a gas-generator designing and regime optimizing. An experimental procedure includes coal char samples of Kuznetskiy and Kansko-Achinskiy deposits consequent argon pyrolysis into argon and oxidating into carbon dioxide with different temperatures. The thermogravimetric analysis data of coal char gasification into carbon dioxide was obtained in the temperature range 900–1200 ºC. The mass loss and gasification time dependencies from temperature were defined to calculate chemical reaction frequency factor and activation energy. Two coal char gasification physico-mathematical models were proposed and recommendations for them were formed.

Coal upgrading

Energy Technology Data Exchange (ETDEWEB)

Nunes, S. [IEA Clean Coal Centre, London (United Kingdom)

2009-10-15

This report examines current technologies and those likely to be used to produce cleaner coal and coal products, principally for use in power generation and metallurgical applications. Consideration is also given to coal production in the leading coal producing countries, both with developed and developing industries. A range of technologies are considered. These include the coal-based liquid fuel called coal water mixture (CWM) that may compete with diesel, the production of ultra-clean coal (UCC) and coal liquefaction which competes with oil and its products. Technologies for upgrading coal are considered, especially for low rank coals (LRC), since these have the potential to fill the gap generated by the increasing demand for coal that cannot be met by higher quality coals. Potential advantages and downsides of coal upgrading are outlined. Taking into account the environmental benefits of reduced pollution achieved through cleaner coal and reduced transport costs, as well as other positive aspects such as a predictable product leading to better boiler design, the advantages appear to be significant. The drying of low rank coals improves the energy productively released during combustion and may also be used as an adjunct or as part of other coal processing procedures. Coal washing technologies vary in different countries and the implications of this are outlined. Dry separation technologies, such as dry jigging and electrostatic separation, are also described. The demonstration of new technologies is key to their further development and demonstrations of various clean coal technologies are considered. A number of approaches to briquetting and pelletising are available and their use varies from country to country. Finally, developments in upgrading low rank coals are described in the leading coal producing countries. This is an area that is developing rapidly and in which there are significant corporate and state players. 81 refs., 32 figs., 3 tabs.

Multi-Sensor Detection with Particle Swarm Optimization for Time-Frequency Coded Cooperative WSNs Based on MC-CDMA for Underground Coal Mines

Directory of Open Access Journals (Sweden)

Jingjing Xu

2015-08-01

Full Text Available In this paper, a wireless sensor network (WSN technology adapted to underground channel conditions is developed, which has important theoretical and practical value for safety monitoring in underground coal mines. According to the characteristics that the space, time and frequency resources of underground tunnel are open, it is proposed to constitute wireless sensor nodes based on multicarrier code division multiple access (MC-CDMA to make full use of these resources. To improve the wireless transmission performance of source sensor nodes, it is also proposed to utilize cooperative sensors with good channel conditions from the sink node to assist source sensors with poor channel conditions. Moreover, the total power of the source sensor and its cooperative sensors is allocated on the basis of their channel conditions to increase the energy efficiency of the WSN. To solve the problem that multiple access interference (MAI arises when multiple source sensors transmit monitoring information simultaneously, a kind of multi-sensor detection (MSD algorithm with particle swarm optimization (PSO, namely D-PSO, is proposed for the time-frequency coded cooperative MC-CDMA WSN. Simulation results show that the average bit error rate (BER performance of the proposed WSN in an underground coal mine is improved significantly by using wireless sensor nodes based on MC-CDMA, adopting time-frequency coded cooperative transmission and D-PSO algorithm with particle swarm optimization.

Multi-Sensor Detection with Particle Swarm Optimization for Time-Frequency Coded Cooperative WSNs Based on MC-CDMA for Underground Coal Mines.

Science.gov (United States)

Xu, Jingjing; Yang, Wei; Zhang, Linyuan; Han, Ruisong; Shao, Xiaotao

2015-08-27

In this paper, a wireless sensor network (WSN) technology adapted to underground channel conditions is developed, which has important theoretical and practical value for safety monitoring in underground coal mines. According to the characteristics that the space, time and frequency resources of underground tunnel are open, it is proposed to constitute wireless sensor nodes based on multicarrier code division multiple access (MC-CDMA) to make full use of these resources. To improve the wireless transmission performance of source sensor nodes, it is also proposed to utilize cooperative sensors with good channel conditions from the sink node to assist source sensors with poor channel conditions. Moreover, the total power of the source sensor and its cooperative sensors is allocated on the basis of their channel conditions to increase the energy efficiency of the WSN. To solve the problem that multiple access interference (MAI) arises when multiple source sensors transmit monitoring information simultaneously, a kind of multi-sensor detection (MSD) algorithm with particle swarm optimization (PSO), namely D-PSO, is proposed for the time-frequency coded cooperative MC-CDMA WSN. Simulation results show that the average bit error rate (BER) performance of the proposed WSN in an underground coal mine is improved significantly by using wireless sensor nodes based on MC-CDMA, adopting time-frequency coded cooperative transmission and D-PSO algorithm with particle swarm optimization.

Enhanced Combustion Low NOx Pulverized Coal Burner

Energy Technology Data Exchange (ETDEWEB)

David Towle; Richard Donais; Todd Hellewell; Robert Lewis; Robert Schrecengost

2007-06-30

economic evaluation and commercial application. During the project performance period, Alstom performed computational fluid dynamics (CFD) modeling and large pilot scale combustion testing in its Industrial Scale Burner Facility (ISBF) at its U.S. Power Plant Laboratories facility in Windsor, Connecticut in support of these objectives. The NOx reduction approach was to optimize near-field combustion to ensure that minimum NOx emissions are achieved with minimal impact on unburned carbon in ash, slagging and fouling, corrosion, and flame stability/turn-down. Several iterations of CFD and combustion testing on a Midwest coal led to an optimized design, which was extensively combustion tested on a range of coals. The data from these tests were then used to validate system costs and benefits versus SCR. Three coals were evaluated during the bench-scale and large pilot-scale testing tasks. The three coals ranged from a very reactive subbituminous coal to a moderately reactive Western bituminous coal to a much less reactive Midwest bituminous coal. Bench-scale testing was comprised of standard ASTM properties evaluation, plus more detailed characterization of fuel properties through drop tube furnace testing and thermogravimetric analysis. Bench-scale characterization of the three test coals showed that both NOx emissions and combustion performance are a strong function of coal properties. The more reactive coals evolved more of their fuel bound nitrogen in the substoichiometric main burner zone than less reactive coal, resulting in the potential for lower NOx emissions. From a combustion point of view, the more reactive coals also showed lower carbon in ash and CO values than the less reactive coal at any given main burner zone stoichiometry. According to bench-scale results, the subbituminous coal was found to be the most amenable to both low NOx, and acceptably low combustibles in the flue gas, in an air staged low NOx system. The Midwest bituminous coal, by contrast, was

MOTORIC STIMULATION RELATED TO FINE MOTORIC DEVELOPMENT ON CHILD

Directory of Open Access Journals (Sweden)

Mira Triharini

2017-07-01

Full Text Available Introduction: Motor developmental stimulation is an activity undertaken to stimulate the children basic skills and so they can grow and develop optimally. Children who obtain a direct stimulus will grow faster than who get less stimulus. Mother’s behavior of stimulation is very important for children, it is considering as the basic needs of children and it must be fulfilled. Providing good stimulation could optimize fine motor development in children. The purpose of this study was to analyze mother’s behavior about motor stimulation with fine motor development in toddler age 4-5 years old. Method: Design have been  used in this study was cross sectional. Population were mothers and their toddler in Group A of Dharma Wanita Persatuan Driyorejo Gresik Preschool. Sample were 51 respondents recruited by using purposive sampling technique according to inclusion and exclusion criteria. The independent variable was mother’s behavior about motor stimulation whereas dependent variable was fine motor development in toddler. The data were collected using questionnaire and conducting observation on fine motor development based on Denver Development Screening Test (DDST. Data then analyzed using Spearman Rho (r test to find relation between mother’s behaviors about stimulation motor on their toddler fine motor development. Result: Results  of this study showed that there were correlations between mother’s knowledge and fine motor development in toddler (p=0.000, between mother’s attitude and fine motor development in toddler (p=0.000, and between mother’s actions and fine motor development in toddler (p=0.000. Analysis: In sort study found that there were relation between fine motor development and mother’s behavior. Discussion: Therefore mother’s behavior needed to be improved. Further research about stimulation motor and fine motor development aspects in toddler is required.

Liquid fuels from Canadian coals

Energy Technology Data Exchange (ETDEWEB)

Taylor, G. W.

1979-06-15

In Canadian energy planning, the central issue of security of supply must be addressed by developing flexible energy systems that make the best possible use of available resources. For liquid fuel production, oil sands and heavy oil currently appear more attractive than coal or biomass as alternatives to conventional crude oil, but the magnitude of their economic advantage is uncertain. The existence of large resources of oil sands, heavy oils, natural gas and low-sulfur coals in Western Canada creates a unique opportunity for Canadians to optimize the yield from these resources and develop new technology. Many variations on the three basic liquefaction routes - hydroliquefaction, pyrolysis and synthesis - are under investigation around the world, and the technology is advancing rapidly. Each process has merit under certain circumstances. Surface-mineable subbituminous and lignite coals of Alberta and Saskatchewan appear to offer the best combination of favorable properties, deposit size and mining cost, but other deposits in Alberta, Nova Scotia and British Columbia should not be ruled out. The research effort in Canada is small by world standards, but it is unlikely that technology could be imported that is ideally suited to Canadian conditions. Importing technology is undesirable: innovation or process modification to suit Canadian coals and markets is preferred; coprocessing of coal liquids with bitumen or heavy oils would be a uniquely Canadian, exportable technology. The cost of synthetic crude from coal in Canada is uncertain, estimates ranging from $113 to $220/m/sup 3/ ($18 to $35/bbl). Existing economic evaluations vary widely depending on assumptions, and can be misleading. Product quality is an important consideration.

The hybrid MPC-MINLP algorithm for optimal operation of coal-fired power plants with solvent based post-combustion CO2 capture

Directory of Open Access Journals (Sweden)

Norhuda Abdul Manaf

2017-03-01

Full Text Available This paper presents an algorithm that combines model predictive control (MPC with MINLP optimization and demonstrates its application for coal-fired power plants retrofitted with solvent based post-combustion CO2 capture (PCC plant. The objective function of the optimization algorithm works at a primary level to maximize plant economic revenue while considering an optimal carbon capture profile. At a secondary level, the MPC algorithm is used to control the performance of the PCC plant. Two techno-economic scenarios based on fixed (capture rate is constant and flexible (capture rate is variable operation modes are developed using actual electricity prices (2011 with fixed carbon prices ($AUD 5, 25, 50/tonne-CO2 for 24 h periods. Results show that fixed operation mode can bring about a ratio of net operating revenue deficit at an average of 6% against the superior flexible operation mode.

Legal Analysis of Coal Mining in Efforts to Maintain The Environmental Sustainability

Directory of Open Access Journals (Sweden)

Iwan Irawan

2016-07-01

Full Text Available The goal of this article was to suggest the government to make the appropriate laws and policies in order to optimize the utilization of coal based on environmental sustainability. The research applied library research from several research results and the Act no. 4 of 2009. Data were analyzed qualitatively by the way of decomposition, connecting with the rules, and the legal experts’ opinion. It can be concluded that investors are not optimal in managing and conserving the coal mining and the government has not standaridized the environmental management. 

Performance of concrete with partial replacement of fine aggregates ...

African Journals Online (AJOL)

The study investigated the level of replacement of fine aggregate with waste glass that will result in optimal compressive strength. A total of 36 cubes were cast. 6 cubes without waste glass (control) and 30 cubes containing waste glass as partial replacement for fine aggregates at 15%, 25%, 35%, 45%, and 50%.

Using system dynamics for simulation and optimization of one coal industry system under fuzzy environment

Energy Technology Data Exchange (ETDEWEB)

Xu, J.P.; Li, X.F. [Sichuan University, Chengdu (China)

2011-09-15

In this paper, we have developed a model that integrates system dynamics with fuzzy multiple objective programming (SD-FMOP). This model can be used to study the complex interactions in a industry system. In the process of confirming sensitive parameters and fuzzy variables of the SD model, we made use of fuzzy multi-objective programming to help yield the solution. We adopted the chance-constraint programming model to convert the fuzzy variables into precise values. We use genetic algorithm to solve FMOP model, and obtain the Pareto solution through the programming models. It is evident that FMOP is effective in optimizing the given system to obtain the decision objectives of the SD model. The results recorded from the SD model are in our option, reasonable and credible. These results may help governments to establish more effective policy related to the coal industry development.

Bio-coal briquettes using low-grade coal

Science.gov (United States)

Estiaty, L. M.; Fatimah, D.; Widodo

2018-02-01

The technology in using briquettes for fuel has been widely used in many countries for both domestic and industrial purposes. Common types of briquette used are coal, peat, charcoal, and biomass. Several researches have been carried out in regards to the production and the use of briquettes. Recently, researches show that mixing coal and biomass will result in an environmentally friendly briquette with better combustion and physical characteristics. This type of briquette is known as bio-coal briquettes. Bio-coal briquettes are made from agriculture waste and coal, which are readily available, cheap and affordable. Researchers make these bio-coal briquettes with different aims and objectives, depending on the issues to address, e.g. utilizing agricultural waste as an alternative energy to replace fossil fuels that are depleting its reserves, adding coal to biomass in order to add calorific value to bio-coal briquette, and adding biomass to coal to improve its chemical and physical properties. In our research, biocoal briquettes are made to utilize low grade coal. The biomass we use, however, is different from the ones used in past researches because it has undergone fermentation. The benefits of using such biomass are 1. Fermentation turns the hemi cellulose into a simpler form, so that the burning activation energy decreases while the calorific value increases. 2. Enzym produced will bind to heavy metals from coal as co-factors, forming metals that are environmentally friendly.

Research on magnetic excitation model of magnetic flux leakage for coal mine hoisting wire rope

Directory of Open Access Journals (Sweden)

Jie Tian

2015-11-01

Full Text Available This study presents the optimal design of a magnetic excitation model for developing a nondestructive sensor for coal mine hoist wire ropes. The model was established using axial-symmetry finite-element analysis and calculations. The influence of the excitation device parameters on the local magnetization effect of the wire rope was investigated in detail using the axial-symmetry finite-element model. The excitation model parameters of the sensor were optimally designed using a combination of finite-element analysis and an optimization method. The experiments were performed to measure the leakage flux and evaluate the performance of the optimally designed sensor. The results show that the sensor based on the newly designed excitation model can not only improve the signal-to-noise ratio for defect detection in a coal mine hoist wire rope by 11% compared to an existing sensor but also reliably detect small defects with a high detection speed (5 m/s along the length of the coal mine wire rope.

Coal

International Nuclear Information System (INIS)

Teissie, J.; Bourgogne, D. de; Bautin, F.

2001-12-01

Coal world production represents 3.5 billions of tons, plus 900 millions of tons of lignite. 50% of coal is used for power generation, 16% by steel making industry, 5% by cement plants, and 29% for space heating and by other industries like carbo-chemistry. Coal reserves are enormous, about 1000 billions of tons (i.e. 250 years of consumption with the present day rate) but their exploitation will be in competition with less costly and less polluting energy sources. This documents treats of all aspects of coal: origin, composition, calorific value, classification, resources, reserves, production, international trade, sectoral consumption, cost, retail price, safety aspects of coal mining, environmental impacts (solid and gaseous effluents), different technologies of coal-fired power plants and their relative efficiency, alternative solutions for the recovery of coal energy (fuel cells, liquefaction). (J.S.)

CoalVal-A coal resource valuation program

Science.gov (United States)

Rohrbacher, Timothy J.; McIntosh, Gary E.

2010-01-01

CoalVal is a menu-driven Windows program that produces cost-of-mining analyses of mine-modeled coal resources. Geological modeling of the coal beds and some degree of mine planning, from basic prefeasibility to advanced, must already have been performed before this program can be used. United States Geological Survey mine planning is done from a very basic, prefeasibility standpoint, but the accuracy of CoalVal's output is a reflection of the accuracy of the data entered, both for mine costs and mine planning. The mining cost analysis is done by using mine cost models designed for the commonly employed, surface and underground mining methods utilized in the United States. CoalVal requires a Microsoft Windows? 98 or Windows? XP operating system and a minimum of 1 gigabyte of random access memory to perform operations. It will not operate on Microsoft Vista?, Windows? 7, or Macintosh? operating systems. The program will summarize the evaluation of an unlimited number of coal seams, haulage zones, tax entities, or other area delineations for a given coal property, coalfield, or basin. When the reader opens the CoalVal publication from the USGS website, options are provided to download the CoalVal publication manual and the CoalVal Program. The CoalVal report is divided into five specific areas relevant to the development and use of the CoalVal program: 1. Introduction to CoalVal Assumptions and Concepts. 2. Mine Model Assumption Details (appendix A). 3. CoalVal Project Tutorial (appendix B). 4. Program Description (appendix C). 5. Mine Model and Discounted Cash Flow Formulas (appendix D). The tutorial explains how to enter coal resource and quality data by mining method; program default values for production, operating, and cost variables; and ones own operating and cost variables into the program. Generated summary reports list the volume of resource in short tons available for mining, recoverable short tons by mining method; the seam or property being mined

Gene-expression profiling of buccal epithelium among non-smoking women exposed to household air pollution from smoky coal

Science.gov (United States)

Wang, Teresa W.; Vermeulen, Roel C.H.; Hu, Wei; Liu, Gang; Xiao, Xiaohui; Alekseyev, Yuriy; Xu, Jun; Reiss, Boris; Steiling, Katrina; Downward, George S.; Silverman, Debra T.; Wei, Fusheng; Wu, Guoping; Li, Jihua; Lenburg, Marc E.; Rothman, Nathaniel; Spira, Avrum; Lan, Qing

2015-01-01

In China’s rural counties of Xuanwei and Fuyuan, lung cancer rates are among the highest in the world. While the elevated disease risk in this population has been linked to the usage of smoky (bituminous) coal as compared to smokeless (anthracite) coal, the underlying molecular changes associated with this exposure remains unclear. To understand the physiologic effects of smoky coal exposure, we analyzed the genome-wide gene-expression profiles in buccal epithelial cells collected from healthy, non-smoking female residents of Xuanwei and Fuyuan who burn smoky (n = 26) and smokeless (n = 9) coal. Gene-expression was profiled via microarrays, and changes associated with coal type were correlated to household levels of fine particulate matter (PM2.5) and polycyclic aromatic hydrocarbons (PAHs). Expression levels of 282 genes were altered with smoky versus smokeless coal exposure (P coal exposure were concordantly enriched with tobacco exposure in previously profiled buccal biopsies of smokers and non-smokers (GSEA, q coal exposure, which in part is similar to the molecular response to tobacco smoke, thereby lending biologic plausibility to prior epidemiological studies that have linked this exposure to lung cancer risk. PMID:26468118

Ultrafine coal classification using 150 mm gMax cyclone circuits

Energy Technology Data Exchange (ETDEWEB)

Honaker, R.Q.; Boaten, F.; Luttrell, G.H. [University of Kentucky, Lexington, KY (United States). Dept. of Mineral Engineering

2007-11-15

A two-stage classification circuit using 150 mm diameter gMax cyclones was installed and evaluated in a coal preparation plant in an effort to achieve a clean coal product without the use of froth flotation. Particle size separations of around 37 {mu}m were achieved while limiting ultrafine bypass to less than 10% in the circuit underflow stream. As a result, approximately 81% of the ash-bearing material in the circuit feed was rejected to the circuit overflow stream. The feed ash content was reduced from around 50% to values in the range of 22-30% in the circuit underflow stream with a mass recovery of about 30%. Further reductions in the coarse product ash content were limited due to the particle density effect and the remaining presence of a significant quantity of high-ash slime material in the coarse product. The typical D{sub 50} for the coal particles was 40 {mu} m while the estimated value for mineral matter was 17 {mu} m. Based on the findings of the study, the use of classification to recover a low-ash, coarse fraction in the feed of a fine coal circuit is limited by the density effect regardless of the ability to eliminate ultrafine bypass.

GEOTECHNICAL/GEOCHEMICAL CHARACTERIZATION OF ADVANCED COAL PROCESS WASTE STREAMS

Energy Technology Data Exchange (ETDEWEB)

Edwin S. Olson; Charles J. Moretti

1999-11-01

Thirteen solid wastes, six coals and one unreacted sorbent produced from seven advanced coal utilization processes were characterized for task three of this project. The advanced processes from which samples were obtained included a gas-reburning sorbent injection process, a pressurized fluidized-bed coal combustion process, a coal-reburning process, a SO{sub x}, NO{sub x}, RO{sub x}, BOX process, an advanced flue desulfurization process, and an advanced coal cleaning process. The waste samples ranged from coarse materials, such as bottom ashes and spent bed materials, to fine materials such as fly ashes and cyclone ashes. Based on the results of the waste characterizations, an analysis of appropriate waste management practices for the advanced process wastes was done. The analysis indicated that using conventional waste management technology should be possible for disposal of all the advanced process wastes studied for task three. However, some wastes did possess properties that could present special problems for conventional waste management systems. Several task three wastes were self-hardening materials and one was self-heating. Self-hardening is caused by cementitious and pozzolanic reactions that occur when water is added to the waste. All of the self-hardening wastes setup slowly (in a matter of hours or days rather than minutes). Thus these wastes can still be handled with conventional management systems if care is taken not to allow them to setup in storage bins or transport vehicles. Waste self-heating is caused by the exothermic hydration of lime when the waste is mixed with conditioning water. If enough lime is present, the temperature of the waste will rise until steam is produced. It is recommended that self-heating wastes be conditioned in a controlled manner so that the heat will be safely dissipated before the material is transported to an ultimate disposal site. Waste utilization is important because an advanced process waste will not require

Coking coal outlook from a coal producer's perspective

International Nuclear Information System (INIS)

Thrasher, E.

2008-01-01

Australian mine production is recovering from massive flooding while Canadian coal shipments are limited by mine and rail capacity. Polish, Czech, and Russian coking coal shipments have been reduced and United States coking coal shipments are reaching their maximum capacity. On the demand side, the Chinese government has increased export taxes on metallurgical coal, coking coal, and thermal coal. Customers seem to be purchasing in waves and steel prices are declining. This presentation addressed the global outlook for coal as well as the challenges ahead in terms of supply and demand. Supply challenges include regulatory uncertainty; environmental permitting; labor; and geology of remaining reserves. Demand challenges include global economic uncertainty; foreign exchange values; the effect of customers making direct investments in mining operations; and freight rates. Consolidation of the coal industry continued and several examples were provided. The presentation also discussed other topics such as coking coal production issues; delayed mining permits and environmental issues; coking coal contract negotiations; and stock values of coking coal producers in the United States. It was concluded that consolidation will continue throughout the natural resource sector. tabs., figs

Coal contract cost reduction through resale of coal

International Nuclear Information System (INIS)

Simon, R.

1990-01-01

The weak coal market of the 1980's has enabled utilities and other users of coal to enjoy stable or falling prices for coal supplies. Falling prices for coal stimulated the renegotiation of numerous coal contracts in recent years, as buyers look to take advantage of lower fuel prices available in the marketplace. This paper examines the use of coal resale transactions as a means of reducing fuel costs, and analyzes the benefits and risks associated with such transactions

Chronic interstitial pneumonia with honeycombing in coal workers

Energy Technology Data Exchange (ETDEWEB)

Brichet, A.; Tonnel, A.B.; Brambilla, E.; Devouassoux, G.; Remy-Jardin, M.; Copin, M.C.; Wallaert, B. [A. Calmette Hospital, Lille (France)

2002-10-01

Coal worker's pneumoconiosis (CWP) results from coal mine dust inhalation. The paper reports the presence of a chronic interstitial pneumonia (CIP) with honeycombing in 38 cases of coal miners, with or without CWP. The 38 patients were selected on the basis of clinical criteria which are unusual in CWP, i.e. fine inspiratory crackles and severe dyspnea. There were 37 men and one woman; mean age was 67.5 {+-} 9.1 years. Thirty-two were smokers. Duration of exposure was 26.7 {+-} 9.9 years. All the patients had clinical examination, chest radiography, computed tomography (CT), lung function, laboratory investigations, wedged fiberoptic bronchoscopy with bronchoalveolar lavage (BAL). In eight cases, lung specimens were obtained. Seventeen out of 38 had finger clubbing. 17 had radiological signs of CWP limited to the upper lobes or diffusely distributed. CT showed honeycombing (36 cases), and/or ground glass opacities (30 cases) with traction bronchiectasis (8 cases) predominant in the lower lobes. BAL analysis demonstrated an increased percentage of neutrophils (9.4% {+-} 6). Lung function showed a restrictive pattern associated with a decreased DLCO and hypoxemia. Lung specimens demonstrated in 2 cases a homogenous interstitial fibrosis of intra-alveolar septum with an accumulation of immune and inflammatory cells without temporal variation and with obvious honeycombing. The 6 other cases showed features of usual interstitial pneumonia. These cases, should alert other clinicians to a possible association between CIP with honeycombing and coal dust exposure, with or without associated CWP.

Distribution of trace elements in selected pulverized coals as a function of particle size and density

Science.gov (United States)

Senior, C.L.; Zeng, T.; Che, J.; Ames, M.R.; Sarofim, A.F.; Olmez, I.; Huggins, Frank E.; Shah, N.; Huffman, G.P.; Kolker, A.; Mroczkowski, S.; Palmer, C.; Finkelman, R.

2000-01-01

Trace elements in coal have diverse modes of occurrence that will greatly influence their behavior in many coal utilization processes. Mode of occurrence is important in determining the partitioning during coal cleaning by conventional processes, the susceptibility to oxidation upon exposure to air, as well as the changes in physical properties upon heating. In this study, three complementary methods were used to determine the concentrations and chemical states of trace elements in pulverized samples of four US coals: Pittsburgh, Illinois No. 6, Elkhorn and Hazard, and Wyodak coals. Neutron Activation Analysis (NAA) was used to measure the absolute concentration of elements in the parent coals and in the size- and density-fractionated samples. Chemical leaching and X-ray absorption fine structure (XAFS) spectroscopy were used to provide information on the form of occurrence of an element in the parent coals. The composition differences between size-segregated coal samples of different density mainly reflect the large density difference between minerals, especially pyrite, and the organic portion of the coal. The heavy density fractions are therefore enriched in pyrite and the elements associated with pyrite, as also shown by the leaching and XAFS methods. Nearly all the As is associated with pyrite in the three bituminous coals studied. The sub-bituminous coal has a very low content of pyrite and arsenic; in this coal arsenic appears to be primarily organically associated. Selenium is mainly associated with pyrite in the bituminous coal samples. In two bituminous coal samples, zinc is mostly in the form of ZnS or associated with pyrite, whereas it appears to be associated with other minerals in the other two coals. Zinc is also the only trace element studied that is significantly more concentrated in the smaller (45 to 63 ??m) coal particles.

Quantitative characterization of pulverized coal and biomass–coal blends in pneumatic conveying pipelines using electrostatic sensor arrays and data fusion techniques

International Nuclear Information System (INIS)

Qian, Xiangchen; Wang, Chao; Yan, Yong; Shao, Jiaqing; Wang, Lijuan; Zhou, Hao

2012-01-01

Quantitative data about the dynamic behaviour of pulverized coal and biomass–coal blends in fuel injection pipelines allow power plant operators to detect variations in fuel supply and oscillations in the flow at an early stage, enable them to balance fuel distribution between fuel feeding pipes and ultimately to achieve higher combustion efficiency and lower greenhouse gas emissions. Electrostatic sensor arrays and data fusion algorithms are combined to provide a non-intrusive solution to the measurement of fuel particle velocity, relative solid concentration and flow stability under pneumatic conveying conditions. Electrostatic sensor arrays with circular and arc-shaped electrodes are integrated in the same sensing head to measure ‘averaged’ and ‘localized’ characteristics of pulverized fuel flow. Data fusion techniques are applied to optimize and integrate the results from the sensor arrays. Experimental tests were conducted on the horizontal section of a 150 mm bore pneumatic conveyor circulating pulverized coal and sawdust under various flow conditions. Test results suggest that pure coal particles travel faster and carry more electrostatic charge than biomass–coal blends. As more biomass particles are added to the flow, the overall velocity of the flow reduces, the electrostatic charge level on particles decreases and the flow becomes less stable compared to the pure coal flow. (paper)

Quantitative characterization of pulverized coal and biomass-coal blends in pneumatic conveying pipelines using electrostatic sensor arrays and data fusion techniques

Science.gov (United States)

Qian, Xiangchen; Yan, Yong; Shao, Jiaqing; Wang, Lijuan; Zhou, Hao; Wang, Chao

2012-08-01

Quantitative data about the dynamic behaviour of pulverized coal and biomass-coal blends in fuel injection pipelines allow power plant operators to detect variations in fuel supply and oscillations in the flow at an early stage, enable them to balance fuel distribution between fuel feeding pipes and ultimately to achieve higher combustion efficiency and lower greenhouse gas emissions. Electrostatic sensor arrays and data fusion algorithms are combined to provide a non-intrusive solution to the measurement of fuel particle velocity, relative solid concentration and flow stability under pneumatic conveying conditions. Electrostatic sensor arrays with circular and arc-shaped electrodes are integrated in the same sensing head to measure ‘averaged’ and ‘localized’ characteristics of pulverized fuel flow. Data fusion techniques are applied to optimize and integrate the results from the sensor arrays. Experimental tests were conducted on the horizontal section of a 150 mm bore pneumatic conveyor circulating pulverized coal and sawdust under various flow conditions. Test results suggest that pure coal particles travel faster and carry more electrostatic charge than biomass-coal blends. As more biomass particles are added to the flow, the overall velocity of the flow reduces, the electrostatic charge level on particles decreases and the flow becomes less stable compared to the pure coal flow.

Technological possibilities for increasing coarse coal yield in the Staszic mine

Energy Technology Data Exchange (ETDEWEB)

Sikora, W; Major, M

1985-06-01

Experiments carried out in the Staszic underground black coal mine in Upper Silesia showed that there is a correlation of coarse coal yield and yield strength of shield supports used at longwall faces. The faces were equipped with Pioma 25-45, Fazos 15-31 and Fazos 19-32 shield supports, KWB 3RDU shearer loaders and Rybnik chain conveyors. Pressure of oil in water emulsion used in the Pioma 25/45 shield supports was reduced from the recommended 30 MPa to 15 MPa or to 10 MPa. Reducing emulsion pressure (and support yield strength) caused an increase in coarse coal yield. Coarse coal yield was also increased by use of Fazos 19/32 shield supports with reduced yield strength. During the tests coarse coal yield increased 1.68% and 2.65%. Test results are shown in 3 diagrams. Investigations carried out in the Staszic mine in 1983 showed that by optimizing yield strength of shield supports coarse coal yield could be increased 2 to 8%. 6 references.

Australian Coal Company Risk Factors: Coal and Oil Prices

OpenAIRE

M. Zahid Hasan; Ronald A. Ratti

2014-01-01

Examination of panel data on listed coal companies on the Australian exchange over January 1999 to February 2010 suggests that market return, interest rate premium, foreign exchange rate risk, and coal price returns are statistically significant in determining the excess return on coal companies’ stock. Coal price return and oil price return increases have statistically significant positive effects on coal company stock returns. A one per cent rise in coal price raises coal company returns ...

Coal Tar and Coal-Tar Pitch

Science.gov (United States)

Learn about coal-tar products, which can raise your risk of skin cancer, lung cancer, and other types of cancer. Examples of coal-tar products include creosote, coal-tar pitch, and certain preparations used to treat skin conditions such as eczema, psoriasis, and dandruff.

Free gold recovery by coal-oil agglomeration

Energy Technology Data Exchange (ETDEWEB)

Kotze, W.; Petersen, F.W. [Cape Technikon Cape Town (South Africa). Dept. of Chemical Engineering

2000-02-01

The gold mining industry has mainly relied upon the use of highly polluting chemicals, such as mercury and cyanide to recover gold from its ores. The Coal Gold Agglomeration (CGA) process was developed some years ago and has the advantage in that gold is recovered by a procedure which has little or no negative impact on the environment. A gold ore containing liberated gold particles is contacted with coal-oil agglomerates, whereby the gold is recovered into the coal/oil phase. Laboratory scale batch tests were performed on an artificial mixture gold slurry and gold recoveries of up to 85% were found under optimized conditions. By recycling the coal/oil phase, it was found that the gold loading onto the agglomerates was increased. Tests performed on an industrial ore yielded slightly lower gold recoveries, and X-ray Diffraction (XRD) analysis on the coal/oil phase showed that minerals other than gold were recovered into this phase. A comparative study was conducted whereby the CGA process was compared to mercury amalgamation. Gold recoveries obtained through amalgamation were 15% lower than by the agglomeration process, which indicates that this process can be considered favourably as an alternative to amalgamation. 16 refs., 2 figs., 6 tabs.

Progress and performance of on-line analyzers of coal

International Nuclear Information System (INIS)

Spencer, C.M.; Brown, D.R.; Gozani, T.; Bozorgmanesh, H.; Bernatowicz, H.; Tassicker, O.J.; Karlson, F.

1982-01-01

This paper describes the past year's progress in the laboratory testing of the most comprehensive Nucoalyzer, the CONAC, and the performance of a Nucoalyzer-Sulfurmeter in special field tests. Previous papers and presentations provide more detailed background information. The near real-time analysis provided by a Nucoalyzer can be used in a variety of strategies to optimize efficiency of coal use. Nucoalyzers can be used to monitor coal deliveries and achieve uniformity in coal storage and recovery. In a coal cleaning plant, on-line analysis with a Nucoalyzer can lead to optimum Btu recovery while meeting specifications for the washed coal. A Nucoalyzer can monitor the blending of different coals to maintain a key cosntituent such as sulfur below a specified level, or can predict sulfur dioxide emissions, allowing feed-forward control to gas scrubbers and precipitators. Variability in coal feed to the boiler can lead to gross changes in thermodynamic efficiency in combustion. In addition, fouling and slagging incidents due to poor coal quality cause costly boiler shutdowns and maintenance. Nucoalyzer monitoring of key constituents and Btu in the coal feed allows operators to adjust boiler parameters for increased efficiency. To summarize, the primary advantages of Nucoalyzers relate to their ability to quickly identify changes in coal composition so that adjustments can be made in a timely manner to accommodate these changes in the process being monitored. Nucoalyzers are the only instruments available that can monitor the coal (for ash, Btu, sulfur, etc.) on-line and provide real-time continuous results. One Nucoalyzer is already working in the field, and by the time of the next Symposium we will have had performance reports on two more

Coal and tire burning mixtures containing ultrafine and nanoparticulate materials induce oxidative stress and inflammatory activation in macrophages.

Science.gov (United States)

Gasparotto, Juciano; Somensi, Nauana; Caregnato, Fernanda F; Rabelo, Thallita K; DaBoit, Kátia; Oliveira, Marcos L S; Moreira, José C F; Gelain, Daniel P

2013-10-01

Ultra-fine and nano-particulate materials resulting from mixtures of coal and non-coal fuels combustion for power generation release to the air components with toxic potential. We evaluated toxicological and inflammatory effects at cellular level that could be induced by ultrafine/nanoparticles-containing ashes from burning mixtures of coal and tires from an American power plant. Coal fly ashes (CFA) samples from the combustion of high-S coal and tire-derived fuel, the latter about 2-3% of the total fuel feed, in a 100-MW cyclone utility boiler, were suspended in the cell culture medium of RAW 264.7 macrophages. Cell viability, assessed by MTT reduction, SRB incorporation and contrast-phase microscopy analysis demonstrated that CFA did not induce acute toxicity. However, CFA at 1mg/mL induced an increase of approximately 338% in intracellular TNF-α, while release of this proinflammatory cytokine was increased by 1.6-fold. The expression of the inflammatory mediator CD40 receptor was enhanced by 2-fold, the receptor for advanced glycation endproducts (RAGE) had a 5.7-fold increase and the stress response protein HSP70 was increased nearly 12-fold by CFA at 1mg/mL. Although CFA did not induce cell death, parameters of oxidative stress and reactive species production were found to be altered at several degrees, such as nitrite accumulation (22% increase), DCFH oxidation (3.5-fold increase), catalase (5-fold increase) and superoxide dismutase (35% inhibition) activities, lipoperoxidation (4.2 fold-increase) and sulfhydryl oxidation (40% decrease in free SH groups). The present results suggest that CFA containing ultra-fine and nano-particulate materials from coal and tire combustion may induce sub-chronic cell damage, as they alter inflammatory and oxidative stress parameters at the molecular and cellular levels, but do not induce acute cell death. © 2013.

Coal summit II

Energy Technology Data Exchange (ETDEWEB)

1983-01-01

Various papers were presented on world coal trade. Papers include: Poland as a producer and exporter of coal; the dynamics of world coal trade; Cerrejon coal production perspectives; present state of the Australian coal industry; present state of the EC coal market and future prospects; prospects of US coal exports to Europe; forecast of Italian coal supply and demand through 1990; statistics from coal transportation outlook; status of world coal ports.

Partitioning of elements during coal combustion and leaching experiments

Energy Technology Data Exchange (ETDEWEB)

Wang Wen-feng; Qin Yong; Song Dang-yu; Wang Jun-yi [China University of Mining & Technology, Xuzhou (China). School of Resources and Earth Science

2009-04-15

The mineral component and content of sulfur and 42 major and trace elements of the feed coal, fly and bottom ashes collected from Shizuishan coal-fired power plant, Ningxia, China were analyzed using AFS, INAA, ICP-MS, ICP-AES, XRD. Based on the coal combustion and leaching experiments, the partitioning of these elements during coal combustion and the leaching behavior of the 11 potentially hazardous elements, including As, Cd, Co, Cr, Hg, Mo, Ni, Pb, Se, Th and U were investigated. The results show that the distribution of elements in the fly and bottom ashes is controlled by their volatilities and modes of occurrence in the coal. The degree of volatilization of elements may be mainly associated with boiling/melting points of these elements and their compounds. The elements easily volatilized, organically bound or associated with sub-micrometer and nano minerals (e.g. Al and Na) tend to be enriched in the fine fractions of fly ash, and most elements do not vaporize which are approximately equally partitioned in the fly and bottom ashes. The emission rates of As, Cr, K, Mg, Mn, Mo, Pb, Sb, and Zn are notably influenced by the temperature ranging from 877 to 1300{sup o}C. The leaching behavior of elements depend significantly on their geochemical properties and modes of occurrence. The elements with a low degree of volatilization are not easily leached, while volatile elements easily leached under the acid conditions. Arsenic, B Br, Cd, Cu, Hg, Pb, S, Sb and Se show a higher emission rate during coal combustion, and the leached concentrations of Cd, Co, Mo, Ni and U in the acid media exceed their limited concentrations recommended in relevant environment quality standards for water, which will harm the environment. 32 refs., 4 figs., 4 tabs.

REGULATION OF COAL POLYMER DEGRADATION BY FUNGI

Energy Technology Data Exchange (ETDEWEB)

John A. Bumpus

1998-11-30

A variety of lignin degrading fungi mediate solubilization and subsequent biodegradation of coal macromolecules (a.k.a. coal polymer) from highly oxidized low rank coals such as leonardites. It appears that oxalate or possibly other metal chelators (i.e., certain Krebs Cycle intermediates) mediate solubilization of low rank coals while extracellular oxidases have a role in subsequent oxidation of solubilized coal macromolecule. These processes are under nutritional control. For example, in the case of P. chrysosporium, solubilization of leonardite occurred when the fungi were cultured on most but not all nutrient agars tested and subsequent biodegradation occurred only in nutrient nitrogen limited cultures. Lignin peroxidases mediate oxidation of coal macromolecule in a reaction that is dependent on the presence of veratryl alcohol and hydrogen peroxide. Kinetic evidence suggests that veratryl alcohol is oxidized to the veratryl alcohol cation radical which then mediates oxidation of the coal macromolecule. Results by others suggest that Mn peroxidases mediate formation of reactive Mn{sup 3+} complexes which also mediate oxidation of coal macromolecule. A biomimetic approach was used to study solubilization of a North Dakota leonardite. It was found that a concentration {approximately}75 mM sodium oxalate was optimal for solubilization of this low rank coal. This is important because this is well above the concentration of oxalate produced by fungi in liquid culture. Higher local concentrations probably occur in solid agar cultures and thus may account for the observation that greater solubilization occurs in agar media relative to liquid media. The characteristics of biomimetically solubilized leonardite were similar to those of biologically solubilized leonardite. Perhaps our most interesting observation was that in addition to oxalate, other common Lewis bases (phosphate/hydrogen phosphate/dihydrogen phosphate and bicarbonate/carbonate ions) are able to mediate

Distillation of coal, wood, peat, etc

Energy Technology Data Exchange (ETDEWEB)

Buhrer, J; Price, A P

1867-02-01

The production of permanent gas for the purposes of illumination or for heating purposes, and also to the production of oils and other distillatory products from coal, shale, wood, peat, and other bituminous or carbonaceous substances, consists in subjecting the before-mentioned materials, previously reduced to a fine state, to a process of distillation causing the same to pass or fall through the interior of a heated vertical tube, chamber, or retort, or series of the same, in such a manner that the particles in their descent or passage shall be subjected to the action of heat in order that the desired products may be obtained.

Optimal thermionic energy conversion with established electrodes for high-temperature topping and process heating. [coal combustion product environments

Science.gov (United States)

Morris, J. F.

1980-01-01

Applied research-and-technology (ART) work reveals that optimal thermionic energy conversion (TEC) with approximately 1000 K to approximately 1100 K collectors is possible using well established tungsten electrodes. Such TEC with 1800 K emitters could approach 26.6% efficiency at 27.4 W/sq cm with approximately 1000 K collectors and 21.7% at 22.6 W/sq cm with approximately 1100 K collectors. These performances require 1.5 and 1.7 eV collector work functions (not the 1 eV ultimate) with nearly negligible interelectrode losses. Such collectors correspond to tungsten electrode systems in approximately 0.9 to approximately 6 torr cesium pressures with 1600 K to 1900 K emitters. Because higher heat-rejection temperatures for TEC allow greater collector work functions, interelectrode loss reduction becomes an increasingly important target for applications aimed at elevated temperatures. Studies of intragap modifications and new electrodes that will allow better electron emission and collection with lower cesium pressures are among the TEC-ART approaches to reduced interelectrode losses. These solutions will provide very effective TEC to serve directly in coal-combustion products for high-temperature topping and process heating. In turn this will help to use coal and to use it well.

Projected configuration of a coal-fired district heating source on the basis of comparative technical-economical optimization analysis

Directory of Open Access Journals (Sweden)

Tańczuk Mariusz

2017-01-01

Full Text Available District heating technologies should be efficient, effective and environmentally friendly. The majority of the communal heating systems in Poland produce district hot water in coal-fired boilers. A large number of them are considerably worn out, low-efficient in the summer time and will not comply with forthcoming regulations. One of the possible solution for such plants is repowering with new CHP systems or new boilers fuelled with fuels alternative to coal. Optimisation analysis of the target configuration of municipal heat generating plant is analysed in the paper. The work concerns repowering the existing conventional heat generating plant according to eight different scenarios of the plant configuration meeting technical and environmental requirements forecasted for the year of 2035. The maximum demand for heat of the system supplied by the plant is 185 MW. Taking into account different technical configurations on one side, and different energy and fuel prices on the other side, the comparative cost-benefits analysis of the assumed scenarios has been made. The basic economical index NPV (net present value has been derived for each analysed scenario and the results have been compared and discussed. It was also claimed that the scenario with CHP based on ICE engines is optimal.

Projected configuration of a coal-fired district heating source on the basis of comparative technical-economical optimization analysis

Science.gov (United States)

Tańczuk, Mariusz; Radziewicz, Wojciech; Olszewski, Eligiusz; Skorek, Janusz

2017-10-01

District heating technologies should be efficient, effective and environmentally friendly. The majority of the communal heating systems in Poland produce district hot water in coal-fired boilers. A large number of them are considerably worn out, low-efficient in the summer time and will not comply with forthcoming regulations. One of the possible solution for such plants is repowering with new CHP systems or new boilers fuelled with fuels alternative to coal. Optimisation analysis of the target configuration of municipal heat generating plant is analysed in the paper. The work concerns repowering the existing conventional heat generating plant according to eight different scenarios of the plant configuration meeting technical and environmental requirements forecasted for the year of 2035. The maximum demand for heat of the system supplied by the plant is 185 MW. Taking into account different technical configurations on one side, and different energy and fuel prices on the other side, the comparative cost-benefits analysis of the assumed scenarios has been made. The basic economical index NPV (net present value) has been derived for each analysed scenario and the results have been compared and discussed. It was also claimed that the scenario with CHP based on ICE engines is optimal.

Gas Concentration Prediction Based on the Measured Data of a Coal Mine Rescue Robot

Directory of Open Access Journals (Sweden)

Xiliang Ma

2016-01-01

Full Text Available The coal mine environment is complex and dangerous after gas accident; then a timely and effective rescue and relief work is necessary. Hence prediction of gas concentration in front of coal mine rescue robot is an important significance to ensure that the coal mine rescue robot carries out the exploration and search and rescue mission. In this paper, a gray neural network is proposed to predict the gas concentration 10 meters in front of the coal mine rescue robot based on the gas concentration, temperature, and wind speed of the current position and 1 meter in front. Subsequently the quantum genetic algorithm optimization gray neural network parameters of the gas concentration prediction method are proposed to get more accurate prediction of the gas concentration in the roadway. Experimental results show that a gray neural network optimized by the quantum genetic algorithm is more accurate for predicting the gas concentration. The overall prediction error is 9.12%, and the largest forecasting error is 11.36%; compared with gray neural network, the gas concentration prediction error increases by 55.23%. This means that the proposed method can better allow the coal mine rescue robot to accurately predict the gas concentration in the coal mine roadway.

Health effects of arsenic, fluorine, and selenium from indoor burning of Chinese coal.

Science.gov (United States)

Guijian, Liu; Liugen, Zheng; Duzgoren-Aydin, Nurdan S; Lianfen, Gao; Junhua, Liu; Zicheng, Peng

2007-01-01

China's economy has developed rapidly in the last two decades, leading to an increase in energy consumption and consequently emissions from energy generation. Coal is a primary energy source in China because of its abundance and will continue to be used in the future. The dominance of coal in energy production is expected to result in increasing levels of exposure to environmental pollution in China. Toxic trace elements emitted during coal combustion are the main sources of indoor air pollution. They are released into the atmosphere mainly in the forms of fine ash and vapors and have the potential to adversely affect human health. Those trace elements, which volatilize during combustion, are hazardous air pollutants (HAPs) and are particularly rich in Chinese coals. Among the HAPs, arsenic (As), fluorine (F), and selenium (Se) have already been identified as pollutants that can induce severe health problems. In this review, the geochemical characteristics of As, F, and Se, including their concentration, distribution, and mode of occurrences in Chinese coal, are documented and discussed. Our investigations have confirmed the current As- and F-induced epidemics in Guizhou (Southwest China) and Se epidemic in Hubei (Northeast China). In this study, diagnostic symptoms of arseniasis, fluorosis, and selenosis are also illustrated.

Health effects of arsenic, fluorine, and selenium from indoor burning of Chinese coal

Energy Technology Data Exchange (ETDEWEB)

Guijian, L.; Liugen, Z.; DuzgorenAydin, N.S.; Lianfen, G.; Junhua, L.; Zicheng, P. [University of Science and Technology of China, Hefei Anhui (China)

2007-07-01

China's economy has developed rapidly in the last two decades, leading to an increase in energy consumption and consequently emissions from energy generation. Coal is a primary energy source in China because of its abundance and will continue to be used in the future. The dominance of coal in energy production is expected to result in increasing levels of exposure to environmental pollution in China. Toxic trace elements emitted during coal combustion are the main sources of indoor air pollution. They are released into the atmosphere mainly in the forms of fine ash and vapors and have the potential to adversely affect human health. Those trace elements, which volatilize during combustion, are hazardous air pollutants (HAPs) and are particularly rich in Chinese coals. Among the HAPs, arsenic (As), fluorine (F), and selenium (Se) have already been identified as pollutants that can induce severe health problems. In this review, the geochemical characteristics of As, F, and Se, including their concentration, distribution, and mode of occurrences in Chinese coal, are documented and discussed. Our investigations have confirmed the current As- and F-induced epidemics in Guizhou (Southwest China) and Se epidemic in Hubei (Northeast China). In this study, diagnostic symptoms of arseniasis, fluorosis, and selenosis are also illustrated.

Optimal planning of co-firing alternative fuels with coal in a power plant by grey nonlinear mixed integer programming model

Energy Technology Data Exchange (ETDEWEB)

Koa, A.S.; Chang, N.B. [University of Central Florida, Orlando, FL (United States). Dept. for Civil & Environmental Engineering

2008-07-15

Energy supply and use is of fundamental importance to society. Although the interactions between energy and environment were originally local in character, they have now widened to cover regional and global issues, such as acid rain and the greenhouse effect. It is for this reason that there is a need for covering the direct and indirect economic and environmental impacts of energy acquisition, transport, production and use. In this paper, particular attention is directed to ways of resolving conflict between economic and environmental goals by encouraging a power plant to consider co-firing biomass and refuse-derived fuel (RDF) with coal simultaneously. It aims at reducing the emission level of sulfur dioxide (SO{sub 2}) in an uncertain environment, using the power plant in Michigan City, Indiana as an example. To assess the uncertainty by a comparative way both deterministic and grey nonlinear mixed integer programming (MIP) models were developed to minimize the net operating cost with respect to possible fuel combinations. It aims at generating the optimal portfolio of alternative fuels while maintaining the same electricity generation simultaneously. To case the solution procedure stepwise relaxation algorithm was developed for solving the grey nonlinear MIP model. Breakeven alternative fuel value can be identified in the post-optimization stage for decision-making. Research findings show that the inclusion of RDF does not exhibit comparative advantage in terms of the net cost, albeit relatively lower air pollution impact. Yet it can be sustained by a charge system, subsidy program, or emission credit as the price of coal increases over time.

Optimal planning of co-firing alternative fuels with coal in a power plant by grey nonlinear mixed integer programming model.

Science.gov (United States)

Ko, Andi Setiady; Chang, Ni-Bin

2008-07-01

Energy supply and use is of fundamental importance to society. Although the interactions between energy and environment were originally local in character, they have now widened to cover regional and global issues, such as acid rain and the greenhouse effect. It is for this reason that there is a need for covering the direct and indirect economic and environmental impacts of energy acquisition, transport, production and use. In this paper, particular attention is directed to ways of resolving conflict between economic and environmental goals by encouraging a power plant to consider co-firing biomass and refuse-derived fuel (RDF) with coal simultaneously. It aims at reducing the emission level of sulfur dioxide (SO(2)) in an uncertain environment, using the power plant in Michigan City, Indiana as an example. To assess the uncertainty by a comparative way both deterministic and grey nonlinear mixed integer programming (MIP) models were developed to minimize the net operating cost with respect to possible fuel combinations. It aims at generating the optimal portfolio of alternative fuels while maintaining the same electricity generation simultaneously. To ease the solution procedure stepwise relaxation algorithm was developed for solving the grey nonlinear MIP model. Breakeven alternative fuel value can be identified in the post-optimization stage for decision-making. Research findings show that the inclusion of RDF does not exhibit comparative advantage in terms of the net cost, albeit relatively lower air pollution impact. Yet it can be sustained by a charge system, subsidy program, or emission credit as the price of coal increases over time.

Hydrothermal conversion of South African coal fly ash into pure phase Zeolite Na-P1

CSIR Research Space (South Africa)

Gitari, MW

2016-08-01

Full Text Available South African coal combustion power utilities generate huge amounts of coal fly ash that can be beneficiated into zeolitic products. This chapter reports on the optimization of the presynthesis and synthesis conditions for a pure-phase zeolite Na-P1...

FY1995 development of economical and high efficient desulfurization process using low rank coal; 1995 nendo teitankadotan wo mochiita ankana kokoritsu datsuryuho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The objective of this study is to develop a new efficient desulfurization technique using a Ca ion-exchanged coal prepared from low rank coal and calcium raw material as a SO{sub 2} sorbent. Ion-exchange of calcium was carried out by soaking and mixing brown coal particles in milk of lime or slurry of industrial waste from concrete manufacture process. About 10wt% of Ca was easily incorporated into Yallourn coal. The ion-exchanged Ca was transformed to ultra-fine CaO particles upon pyrolysis of coal. The reactivity of CaO produced from Ca-exchanged coal to SO{sub 2} was extraordinary high and the CaO utilization of above 90% was easily achieved, while the conversion of natural limestone was less than 30% under the similar experimental conditions. High activity of Ca-exchanged coal was appreciably observed in a pressurized fluidized bed combustor. Ca-exchanged coal was quite effective for the removal of hydrogen sulfide. (NEDO)

Coal stream composition analysis for process control using prompt neutron activation analysis

International Nuclear Information System (INIS)

Gozani, T.; Reynolds, G.; Elias, E.; Maung, T.; Bozorgmanesh, H.; Orphan, V.

1977-01-01

In this paper we describe early results of a series of laboratory experiments and computer modeling studies designed to provide realistic accuracy limits for the determination of the elemental concentration in coal using prompt neutron activation analysis. The results provide guidance for optimizing the technique for monitoring the quality of coal which is being input to an electric power generating plant. The reported work was performed as the initial phase of an ongoing program to develop a prototype on-line coal analyzer based on the PNAA technique for power plant application

Coal-92

International Nuclear Information System (INIS)

Hillring, B.; Sparre, C.

1992-11-01

Swedish consumption of coal and coke during 1991 and trends in technology, environment and market aspects of coal use are reported. Steam coal use in the heating sector was unchanged from 1991, 1.2 Mtons. Reduced consumption in smaller district heating units (due to conversion to biofuels and gas) was compensated by increased use for power generation in cogeneration plants. Coal consumption in industry fell 0.10 Mton to 0.84 Mton due to lower production in one industry branch. Import of steam coal was 1.1 Mton (down 0.5 Mton from 1990) since new rules for strategic reserves allowed a reduction of stocks. During the last five years stocks have been reduced by 2 Mtons. Import of metallurgical coal was 1.6 Mton, unchanged from 1990. The report also gives statistics for the coal using plants in Sweden, on coal R and D, and on emission laws for coal firing. (9 tabs., 2 figs.)

Biotransformation of Spanish coals by microorganisms; Biotransformacion de Carbones Espanoles por Microorganismos

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

some newly isolated microorganisms could solubilized different kinds of Spanish coals (hard coal, subbituminous coal and lignite). Certain fungi and bacteria could solubilized lignite when growing in a mineral medium. However, to solubilized higher rank coals (hard coal and subbituminous coal) microorganisms require a complete medium. Microorganisms, which showed higher capacity to solubilized coal, were incubated in the presence of coal (hard coal, subbituminous coal and lignite) at the optimal conditions to get coal liquefaction/solubilization. The resultant products were analysed by IR and UV/visible spectrometry. No major differences among the original coal, solubilized/liquefied coal and residual coal were detected. However, an increase in metallic carboxylate and a decrease in OH'- carboxylic groups were observed in the liquefied lignite. Humic acids derived from original lignite residual lignite and liquefied/solubilized lignite by microorganisms were analysed. Several differences were observed in the humic acids extracted from the liquefied lignite, such as an increase in the total acidity and in the proportion of the phenolic groups. Differences on the humic acid molecular weight were observed too. Several fungal and bacterial strains were able to grow using humic acids as sole carbon source. Microorganisms growing in humic acid were observed by Scanning Electron Microscopy. Besides, the coal solubilization capacity of several fungal strains (M2, m$ and AGI) growing in different culture media was assayed. In order to get some insight into the mechanisms of the liquefaction/solubilization of Spanish coals (hard coal, subbituminous coal and lignite) by these microorganisms, some features in the culture supernatants were studied: pH values; extracellular specific proteins; enzyme activities possibly related with coal solubilization and the presence of oxalate. M2 and M4 fungal strains grown in the presence of coal produced some specific extracellular proteins

Biotransformation of Spanish coals by microorganisms; Biotransformacion de Carbones Espanoles por Microorganismos

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

some newly isolated microorganisms could solubilized different kinds of Spanish coals (hard coal, subbituminous coal and lignite). Certain fungi and bacteria could solubilized lignite when growing in a mineral medium. However, to solubilized higher rank coals (hard coal and subbituminous coal) microorganisms require a complete medium. Microorganisms, which showed higher capacity to solubilized coal, were incubated in the presence of coal (hard coal, subbituminous coal and lignite) at the optimal conditions to get coal liquefaction/solubilization. The resultant products were analysed by IR and UV/visible spectrometry. No major differences among the original coal, solubilized/liquefied coal and residual coal were detected. However, an increase in metallic carboxylate and a decrease in OH'- carboxylic groups were observed in the liquefied lignite. Humic acids derived from original lignite residual lignite and liquefied/solubilized lignite by microorganisms were analysed. Several differences were observed in the humic acids extracted from the liquefied lignite, such as an increase in the total acidity and in the proportion of the phenolic groups. Differences on the humic acid molecular weight were observed too. Several fungal and bacterial strains were able to grow using humic acids as sole carbon source. Microorganisms growing in humic acid were observed by Scanning Electron Microscopy. Besides, the coal solubilization capacity of several fungal strains (M2, m$ and AGI) growing in different culture media was assayed. In order to get some insight into the mechanisms of the liquefaction/solubilization of Spanish coals (hard coal, subbituminous coal and lignite) by these microorganisms, some features in the culture supernatants were studied: pH values; extracellular specific proteins; enzyme activities possibly related with coal solubilization and the presence of oxalate. M2 and M4 fungal strains grown in the presence of coal produced some specific extracellular

Analysis of waste coal from the enterprises of Kemerovo region as raw materials for production of ceramic materials

Science.gov (United States)

Stolboushkin, A. Yu; Akst, D. V.; Fomina, O. A.; Ivanov, A. I.; Syromyasov, V. A.

2017-09-01

The analysis of waste coal from mining enterprises of Kemerovo region as raw materials for production of building ceramics is given. The results of studies of material, chemical and mineralogical compositions of waste coal from Abashevskaya processing plant (Novokuznetsk) are presented. It was established that the chemical composition of waste coal refers to aluminosilicate raw materials with a high content of alumina and coloring oxides, the residual carbon content in the wastes is 12-25 %. According to the granulometric composition the waste coal is basically a sandy-dusty fraction with a small amount of clay particles (1-3 %). Additional grinding of coal waste and the introduction of a clay additive in an amount of up to 30 % are recommended. The results of the study of the mineral composition of waste coal are presented. Clay minerals are represented in the descending order by hydromuscovite, montmorillonite and kaolinite, minerals-impurities consist of quartz, feldspar fine-dispersed carbonates. The results of the investigation of ceramic-technological properties of waste coal, which belong to the group of moderately plastic low-melting raw materials, are given. As a result of a comprehensive study it was been established that with chemical, granulometric and mineralogical compositions waste coal with the reduced residual carbon can be used in the production of ceramic bricks.

Survey on improvement in development of coal in Asia-Pacific region in fiscal 1998. Survey on expansion of production of high-grade coal in Shanxi Province, China; 1998 nendo Asia Taiheiyo sekitan kaihatsu kodoka chosa. Chugoku Sanseisho ni okeru kohin'itan no seisan kakudai ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With the Datong mining area as the object, a Japan-China joint survey was carried out on improvement in coal development. The Datong coal field is the largest coal field in China. Measures for improving and stabilizing the quality of the coal are planned to achieve stable supply of high-grade coal to Japan. The city of Datong occupies a large part of the Datong coal field, producing more than 40 million tons. Minable reserve quantity reaches 2.47 billion tons. Measures to prevent foreign materials (such as detonators and metal pieces) from mixing in, and quality stabilization are the problems to be solved. Required measures include first of all not putting out used detonators, optimization and multiplexing of the magnet separator installing positions. Variation in the grade of original coal may include regional variation and that caused from coal beds, whereas optimization in coal dressing is important in improving the grade of coal product. The coal dressing rate at three coal mines possessing a coal dressing factory is 40 to 50%, and twelve other coal mines depend on sieve sorting. An on-line analyzer for product coal grade control is also required. Coal shipment and storage management is also important. Indispensable is structuring a system to feed back users' claims, evaluation and information. (NEDO)

Report on the FY 1999 project for training coal engineers. Advanced course; 1999 nendo sekitan gijutsusha yosei jigyo hokokusho. Jokyusha course

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

This is a report on the training for coal technology which two Japanese engineers received in Australia. In Chapter 3 (Outline of Australia), they studied the national land, constitution of the national land, population, history, politics, economy and trade. In Chapter 4 (Coal geology), they read lecture data of university. In Chapter 5 (Outline of coal supply/demand), the coal export amount from Australia is 167 million tons. Steam coal of a little less than 50% is exported to Japan. In Chapter 6 (Coal mining technology), 100 million tons of NSW state and 100 million and 570 thousand tons of QLD state are mined by underground mining and open pit mining. Training was conducted on overburden/drilling/transportation of the open pit mining coal. As coal mining methods of underground mining, they learned the board and pillar coal mining and high wall mining as an extension of open pit mining. In Chapter 7 (Coal preparation), they observed/studied the jig, heavy media separator, heavy media cyclone separator, flotation equipment, spiral ore dressing equipment, fine powder centrifugal dewatering equipment, thickener, sieve, etc. They studied by data or by observation in Chapters 8 (Outline of coal mine), 9 (Outline of export port), 10 (Outline of railroad transportation), and 11 (Quality management). (NEDO)

A newer concept of setting up coal refineries in coal utilising industries through environmentally sound clean coal technology of organosuper refining of coals

International Nuclear Information System (INIS)

Sharma, D.K.

1994-01-01

In order to reduce the losses of premium organic matter of coal and its immense potential energy which is present in the form of stronger interatomic and intramolecular bonding energies, a newer and convenient technique of recovering the premium organic matter from low grade coals by organosuper-refining technique which operates under ambient pressure conditions has been developed. The residual coal obtained can be used as environmentally clean fuel or as a feedstock for the industries based on carbonization and gasification. It is suggested that a beginning be made by setting up coal refineries in coal utilizing industries on the basis of the presently developed new technology of organosuper-refining of coals to recover premium grade organic chemical feed stocks from coals before utilizing coal by techniques such as bubble bed or recirculatory fluidized bed or pulverized coal combustion in thermal power stations, carbonization in steel plants or other carbonization units, gasification in fertilizer industries or in integrated coal gasification combined cycle power generation. Thus, coal refineries may produce value added aromatic chemical feed stocks, formed coke or coke manufacturing; and carbon fillers for polymers. (author). 100 refs., 1 fig

Effects of coal composition and flotation reagents on the water resistance of binderless briquettes

Energy Technology Data Exchange (ETDEWEB)

Motaung, S.R.; Mangena, S.J.; de Korte, G.J. [Syngas & Coal Technology, Sasolburg (South Africa)

2007-10-15

The difference in the physical properties, particularly the water resistance or wet strength, of the binderless coal briquettes produced from flotation feed and concentrate was investigated using six bituminous coals from two collieries in the Witbank Coalfield. The coal samples were analyzed for their proximate, petrographic, and mineralogical properties. The presence, in the flotation concentrates, of the reagents used during the froth flotation process was also investigated using gas chromatography. Pillow-shaped binderless briquettes were produced from coal samples at various moisture contents and a pressure of approximately 17 MPA using a Komarek B-100A double-roll press. The briquettes were tested for some physical properties (i.e., dry- and wet-compressive strengths), which were thereafter compared with the properties determined for the coal samples. The binderless briquettes produced from the flotation concentrates were more water-resistant than those produced from the flotation feed. The flotation feed and concentrates of the coals tested were found to have similar petrographic properties. As expected, the ash and kaolinite contents were found to be lower in the flotation concentrates than in the flotation feed. Flotation reagents were detected in the flotation concentrates from both collieries. From the results obtained it is concluded that the increased water resistance of the binderless briquettes produced from flotation concentrates of the coals tested is due to a combination of the fineness of the coal particles, assisted by the amount of reactive macerals (most particularly vitrinite) with the lower ash and kaolinite contents, together with the presence of the flotation reagents, particularly the collector, in the flotation concentrate.

Fiscal 1997 feasibility survey of an environment friendly type coal utilization system. Feasibility survey of the environment friendly type coal utilization system in Malaysia and Vietnam (case of Vietnam); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Malaysia oyobi Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa (Vietnam ban))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper grasped the state of coal utilization by coal consumption field, the state of coal physical flow in Vietnam, etc., surveyed/studied a possibility of introducing the environment friendly type coal utilization system, and assessed the possibility. As to energy resources, the north is abundant in hydroelectric and coal (mainly anthracite) resources, and the south in oil and natural gas resources. Coal production in fiscal 1997 is planned to be 10 million tons. Coal preparation technique presently available is only grain size sieving. Accordingly, it is necessary to study for heightening efficiency of facilities and modernizing facilities in accordance with the introduction of the environment friendly type coal utilization technology. During the study, it is possible to propose improvement on coal processing technology (coal preparation technology). Assessment and study are made especially of the coal selection system, fine coal recovery system and waste water treatment system. For the plan on new coal-fired power plants (300MWtimes4), there is left much necessity of proposing studying models considered of the anthracite combustion technology and environmental improvement and of assessing/studying them. 60 figs., 117 tabs.

3D numerical modeling of longwall mining with top-coal caving

Energy Technology Data Exchange (ETDEWEB)

Yasitli, N.E.; Unver, B. [Hacettepe University, Ankara (Turkey). Dept. of Mining Engineering

2005-02-01

Top-coal caving is the key factor affecting the efficiency of production at thick-coal seams. During production of top coal by caving behind the face not only a significant amount of coal is lost in the goaf but the coal drawn by means of caving is diluted considerably with surrounding rock. Therefore, it is not possible to carry out an efficient production operation unless caving of top coal behind the face is optimized. In this paper, results of 3D modeling of the top-coal-caving mechanism by using the finite difference code FLAC3{sup D} at the M3 longwall panel of the Omerler Underground Mine located at Tuncbilek (Turkey) are presented. According to the modeling results, maximum vertical abutment stresses were formed at a distance of 7m in front of the face. An analysis of the conditions of top coal has revealed that a 1.5 m thick layer of coal just above the shield supports is well fractured. However, a 3.5 m thick layer of coal above the fractured part is either not fractured or is fractured in the form of large blocks leading to obstruction of windows of shields during coal drawing. It is concluded that, in order to decrease dilution and increase extraction ratio and efficiency of operation, top coal should be as uniformly fractured as possible. Hence, an efficient and continuous coal flowing behind the face can be maintained. A special pre-fracture blasting strategy just sufficient enough to form cracks in the top coal is suggested by means of comparing with the results of numerical modeling.

Importance of the textural characteristics of inert additives in the reduction of coal thermoplastic properties

Energy Technology Data Exchange (ETDEWEB)

A.M. Fernandez; C. Barriocanal; M.A. Diez; R. Alvarez [Instituto Nacional del Carbon, Oviedo (Spain)

2010-11-15

Seven carbonaceous materials of different origin were chosen in order to study the influence of their porous structure on the modification of the thermoplastic properties of a bituminous coal. The materials included were: two non-coking coals, a petroleum coke, coke fines, two residues from tyre recycling and a bituminous residue. The materials were heat-treated to 900{sup o}C to prevent any chemical interaction between the volatiles evolved during co-carbonization. The thermoplastic properties of blends that contained 10 wt.% of additive were measured by means of the Gieseler test. Microporosity was measured by CO{sub 2} adsorption at 273 K, whereas meso and macroporosity were determined by means of mercury porosimetry. The results of the porous structure assessment are discussed in relation to the modification of coal plasticity. 32 refs., 5 figs., 5 tabs.

Evaluation criteria for enhanced solar–coal hybrid power plant performance

International Nuclear Information System (INIS)

Zhao, Yawen; Hong, Hui; Jin, Hongguang

2014-01-01

Attention has been directed toward hybridizing solar energy with fossil power plants since the 1990s to improve reliability and efficiency. Appropriate evaluation criteria were important in the design and optimization of solar–fossil hybrid systems. Two new criteria to evaluate the improved thermodynamic performances in a solar hybrid power plant were developed in this study. Correlations determined the main factors influencing the improved thermodynamic performances. The proposed criteria can be used to effectively integrate solar–coal hybridization systems. Typical 100 MW–1000 MW coal-fired power plants hybridized with solar heat at approximately 300 °C, which was used to preheat the feed water before entering the boiler, were evaluated using the criteria. The integration principle of solar–coal hybrid systems was also determined. The proposed evaluation criteria may be simple and reasonable for solar–coal hybrid systems with multi-energy input, thus directing system performance enhancement. - Highlights: • New criteria to evaluate the solar hybrid power plant were developed. • Typical solar–coal hybrid power plants were evaluated using the criteria. • The integration principle of solar–coal hybrid systems was determined. • The benefits of the solar–coal hybrid system are enhanced at lower solar radiation

Predicted coal production trends in Kentucky: The results of available coal resources, coal quality demands, and regulatory factors

International Nuclear Information System (INIS)

Watson, W.D.

1993-01-01

Many factors affect the viability of regional coal production markets including (1) coal quality and recoverable tonnage, (2) coal mining cost, (3) the regional and time varying patterns of coal demand growth, (4) regulations and other institutional constraints that affect coal demand and utilization, and (5) the regional array of coal transport modes and rates. This analysis integrates these factors into an assessment of coal production prospects (separately) for eastern and western Kentucky coal producing counties for the decade of the 90's. The integration indicates that eastern Kentucky coal production will peak and begin to decline by the end of the decade whereas western Kentucky coal production will continue to grow. No single factor explains these trends. There is plenty of available minable coal. The combination of changes in environmental regulations, some increase in coal mining costs, and the mining-out of low sulfur reserves are the main factors that account for the production trends

Project to develop and demonstrate methods to eliminate frozen coal handling problems. Status report I

Energy Technology Data Exchange (ETDEWEB)

None

1980-09-15

For too many years, problems associated with frozen coal have plagued the companies who mine it, the companies who handle it in transit and the utilities and other industrial concerns that finally burn it. But never before has the magnitude of the frozen coal problem been as great as it is today because of two primary factors, i.e. (1) the majority of coal currently transported and used has been ground to a very fine mesh that absorbs water readily, thus providing more surface area for freezing, and (2) the substantially increased importance of coal, indeed, the now critical necessity for more coal to be used in displacing dangerously uncertain foreign oil supplies that currently account for 50 percent of our daily domestic oil consumption. Frozen coal problems can and do have a devastating effect upon the ability to provide energy from coal during harsh winter months when it is not needed. The majority of these problems have been involved with removing frozen coal from rail cars. To allay the problem, numerous techniques have been tried, all with some measure of success. As an example, certain chemicals have been sprayed on the coal; another common treatment has been widespread use of thaw sheds, which, whether electrically or gas-fired, are all energy intensive, time consuming, hard on rail equipment and expensive to operate over long periods of time. From sledge hammers and crow bars to gas-fired jets and electric thaw sheds, available mechanical de-icing methods often damage coal handling equipment, are time consuming and, therefore, very expensive when demurrage losses must be added to significant investment and/or operating costs.

PM2.5 chemical source profiles for vehicle exhaust, vegetative burning, geological material, and coal burning in Northwestern Colorado during 1995

International Nuclear Information System (INIS)

Watson, J.G.; Chow, J.C.; Houck, J.E.

2001-01-01

PM 2.5 (particles with aerodynamic diameters less than 2.5 μm) chemical source profiles applicable to speciated emissions inventories and receptor model source apportionment are reported for geological material, motor vehicle exhaust, residential coal (RCC) and wood combustion (RWC), forest fires, geothermal hot springs; and coal-fired power generation units from northwestern Colorado during 1995. Fuels and combustion conditions are similar to those of other communities of the inland western US. Coal-fired power station profiles differed substantially between different units using similar coals, with the major difference being lack of selenium in emissions from the only unit that was equipped with a dry limestone sulfur dioxide (SO 2 ) scrubber. SO 2 abundances relative to fine particle mass emissions in power plant emissions were seven to nine times higher than hydrogen sulfide (H 2 S) abundances from geothermal springs, and one to two orders of magnitude higher than SO 2 abundances in RCC emissions, implying that the SO 2 abundance is an important marker for primary particle contributions of non-aged coal-fired power station contributions. The sum of organic and elemental carbon ranged from 1% to 10% of fine particle mass in coal-fired power plant emissions, from 5% to 10% in geological material, >50% in forest fire emissions, >60% in RWC emissions, and >95% in RCC and vehicle exhaust emissions. Water-soluble potassium (K + ) was most abundant in vegetative burning profiles. K + /K ratios ranged from 0.1 in geological material profiles to 0.9 in vegetative burning emissions, confirming previous observations that soluble potassium is a good marker for vegetative burning. (Author)

Variability of Mercury Content in Coal Matter From Coal Seams of The Upper Silesia Coal Basin

Science.gov (United States)

Wierzchowski, Krzysztof; Chećko, Jarosław; Pyka, Ireneusz

2017-12-01

The process of identifying and documenting the quality parameters of coal, as well as the conditions of coal deposition in the seam, is multi-stage and extremely expensive. The taking and analyzing of seam samples is the method of assessment of the quality and quantity parameters of coals in deep mines. Depending on the method of sampling, it offers quite precise assessment of the quality parameters of potential commercial coals. The main kind of seam samples under consideration are so-called "documentary seam samples", which exclude dirt bands and other seam contaminants. Mercury content in coal matter from the currently accessible and exploited coal seams of the Upper Silesian Coal Basin (USCB) was assessed. It was noted that the mercury content in coal seams decreases with the age of the seam and, to a lesser extent, seam deposition depth. Maps of the variation of mercury content in selected lithostratigraphic units (layers) of the Upper Silesian Coal Basin have been created.

Interrelating the breakage and composition of mined and drill core coal

Science.gov (United States)

Wilson, Terril Edward

Particle size distribution of coal is important if the coal is to be beneficiated, or if a coal sales contract includes particle size specifications. An exploration bore core sample of coal ought to be reduced from its original cylindrical form to a particle size distribution and particle composition that reflects, insofar as possible, a process stream of raw coal it represents. Often, coal cores are reduced with a laboratory crushing machine, the product of which does not match the raw coal size distribution. This study proceeds from work in coal bore core reduction by Australian investigators. In this study, as differentiated from the Australian work, drop-shatter impact breakage followed by dry batch tumbling in steel cylinder rotated about its transverse axis are employed to characterize the core material in terms of first-order and zeroth-order breakage rate constants, which are indices of the propensity of the coal to degrade during excavation and handling. Initial drop-shatter and dry tumbling calibrations were done with synthetic cores composed of controlled low-strength concrete incorporating fly ash (as a partial substitute for Portland cement) in order to reduce material variables and conserve difficult-to-obtain coal cores. Cores of three different coalbeds--Illinois No. 6, Upper Freeport, and Pocahontas No. 5 were subjected to drop-shatter and dry batch tumbling tests to determine breakage response. First-order breakage, characterized by a first-order breakage index for each coal, occurred in the drop-shatter tests. First- and zeroth-order breakage occurred in dry batch tumbling; disappearance of coarse particles and creation of fine particles occurred in a systematic way that could be represented mathematically. Certain of the coal cores available for testing were dry and friable. Comparison of coal preparation plant feed with a crushed bore core and a bore core prepared by drop-shatter and tumbling (all from the same Illinois No.6 coal mining

Coal blending preparation for non-carbonized coal briquettes

Science.gov (United States)

Widodo; Fatimah, D.; Estiaty, L. M.

2018-02-01

Referring to the national energy policy targets for the years 2025, the government has launched the use of coal briquettes as an alternative energy replacement for kerosene and firewood. Non-carbonized briquettes in the form of coal briquettes as well as bio-coal briquettes are used in many small-medium industries and households, and are rarely used by large industries. The standard quality of coal briquettes used as raw material for non-carbonized briquettes is a minimum calorific value of 4,400 kcal/kg (adb); total sulfur at a maximum of 1% (adb), and water content at plants), the environment of deposition, and the geological conditions of the surrounding area, so that the coal deposits in each region will be different as well as the amount and also the quality. Therefore, the quantity and the quality of coal in each area are different to be eligible in the making of briquettes to do blending. In addition to the coal blending, it is also necessary to select the right materials in the making of coal briquettes and bio-coal briquettes. The formulation of the right mixture of material in the making of briquettes, can be produced of good quality and environmental friendly.

Dependence of Pyrolysis Rate of Coal on Temperature

Directory of Open Access Journals (Sweden)

Slyusarskiy Konstantin V.

2015-01-01

Full Text Available Pyrolysis process of coal has been researched to define kinetic constants which can be used for design and optimization of different processes of fuel transformation. The article considers anthracite powders and bituminous coal of Krasnogorsky mine with the use of non-isothermal thermogravimetric analysis with mass spectrometry. Spectroscanning microscopy and laser diffraction for definition of sizes and forms of particles distribution has been done. Other parameters – carbon content, ash and volatiles, density and moisture have been defined by standard methods. Energy of activation and pre-exponent with the use of models of Freedman, Starink and distributed activation energy model (DAEM, and also relative deviation of design data from experimental ones have been designed. The results of the analysis have shown the important influence of volatiles content and coal transformation degree on maximum reaction rate. Energy activation values received with the help of DAEM model are higher than with Freedman and Starink models. Process of pyrolysis of bituminous coal has a big rate in comparison with anthracite, and is better described by the above-mentioned models.

Research of Dust Field Optimization Distribution Based on Parameters Change of Air Duct Outlet in Fully Mechanized Excavation Face of Coal Mine

Science.gov (United States)

Gong, Xiao-Yan; Xia, Zhi-Xin; Wu, Yue; Mo, Jin-Ming; Zhang, Xin-Yi

2017-12-01

Aiming at the problem of dust accumulation and pollution risk rising sharply in fully mechanized excavation face, which caused by the unreasonable air duct outlet airflow under the long distance driving, this paper proposes a new idea to optimize the distribution of dust by changing the angle, caliber and the front and rear distance of air duct outlet. Taking the fully mechanized excavation face of Ningtiaota coal mine which located in Shaanxi province as the research object, the numerical simulation scheme of dust field was established, the safety hazard of the distribution of original dust field was simulated and analyzed, the numerical simulation and optimization analysis of the dust distribution by changing the angle, caliber and the front and rear distance of air duct outlet was carried out, and the adjustment scheme of the optimized dust distribution was obtained, which provides a theoretical basis for reducing the probability of dust explosion and the degree of pollution.

Firing a sub-bituminous coal in pulverized coal boilers configured for bituminous coals

Energy Technology Data Exchange (ETDEWEB)

N. Spitz; R. Saveliev; M. Perelman; E. Korytni; B. Chudnovsky; A. Talanker; E. Bar-Ziv [Ben-Gurion University of the Negev, Beer-Sheva (Israel)

2008-07-15

It is important to adapt utility boilers to sub-bituminous coals to take advantage of their environmental benefits while limiting operation risks. We discuss the performance impact that Adaro, an Indonesian sub-bituminous coal with high moisture content, has on opposite-wall and tangentially-fired utility boilers which were designed for bituminous coals. Numerical simulations were made with GLACIER, a computational-fluid-dynamic code, to depict combustion behavior. The predictions were verified with full-scale test results. For analysis of the operational parameters for firing Adaro coal in both boilers, we used EXPERT system, an on-line supervision system developed by Israel Electric Corporation. It was concluded that firing Adaro coal, compared to a typical bituminous coal, lowers NOx and SO{sub 2} emissions, lowers LOI content and improves fouling behavior but can cause load limitation which impacts flexible operation. 21 refs., 7 figs., 3 tabs.

Recovery of Rare Earth Elements from Coal and Coal Byproducts via a Closed Loop Leaching Process: Final Report

Energy Technology Data Exchange (ETDEWEB)