WorldWideScience

Sample records for optical frequency domain

  1. Frequency-Domain Optical Mammogram

    Science.gov (United States)

    2002-10-01

    the tumor. * Combination of the above two points into a composite false-color breast image containing structural information (from the second...Antonangeli, A. Savoia, T. Parasassi, and N. Rosato, " Plastique : a synchrotron radiation beamline for time resolved fluorescence in the frequency domain

  2. High-speed optical frequency-domain imaging

    OpenAIRE

    Yun, S. H.; Tearney, G. J.; Boer; Iftimia, N. V.; Bouma, B. E.

    2003-01-01

    We demonstrate high-speed, high-sensitivity, high-resolution optical imaging based on optical frequency-domain interferometry using a rapidly-tuned wavelength-swept laser. We derive and show experimentally that frequency-domain ranging provides a superior signal-to-noise ratio compared with conventional time-domain ranging as used in optical coherence tomography. A high sensitivity of −110 dB was obtained with a 6 mW source at an axial resolution of 13.5 µm and an A-line rate of 15.7 kHz, rep...

  3. Incoherent Optical Frequency Domain Reflectometry for Distributed Thermal Sensing

    DEFF Research Database (Denmark)

    Karamehmedovic, Emir

    2006-01-01

    This thesis reports the main results from an investigation of a fibre-optic distributed temperature sensor based on spontaneous Raman scattering. The technique used for spatial resolving is the incoherent optical frequency domain reflectometry, where a pump laser is sine modulated with a stepwise...... increasing frequency, after which the inverse Fourier transform is applied to the signal from the backscattered light. This technique is compared with the more conventional optical time domain reflectometry, where a short pulse is sent through the fibre, and the location of the scattering section...... is determined by the time difference from the emission to the detection of light. A temperature sensor with a range of 2-4km comprising a step-index multi-mode fibre and a high-power 980nm pump laser existed prior to the start of the PhD study. In this study, a sensor range of approximately 10km, and a spatial...

  4. Broadband ultrasonic sensor array via optical frequency domain reflectometry

    Science.gov (United States)

    Gabai, Haniel; Steinberg, Idan; Eyal, Avishay

    2015-03-01

    We introduce a new approach for multiplexing fiber-based ultrasound sensors using Optical Frequency Domain Reflectometry (OFDR). In the present demonstration of the method, each sensor was a short section of Polyimide-coated single-mode fiber. One end of the sensing fiber was pigtailed to a mirror and the other end was connected, via a fiber optic delay line, to a 1X4 fiber coupler. The multiplexing was enabled by using a different delay to each sensor. Ultrasonic excitation was performed by a 1MHz transducer which transmitted 4μs tone-bursts above the sensor array. The ultrasound waves generated optical phase variations in the fibers which were detected using the OFDR method. The ultrasound field at the sensors was successfully reconstructed without any noticeable cross-talk.

  5. Frequency-domain optical mammography: edge effect corrections.

    Science.gov (United States)

    Fantini, S; Franceschini, M A; Gaida, G; Gratton, E; Jess, H; Mantulin, W W; Moesta, K T; Schlag, P M; Kaschke, M

    1996-01-01

    We have investigated the problem of edge effects in laser-beam transillumination scanning of the human breast. Edge effects arise from tissue thickness variability along the scanned area, and from lateral photon losses through the sides of the breast. Edge effects can be effectively corrected in frequency-domain measurements by employing a two-step procedure: (1) use of the phase information to calculate an effective tissue thickness for each pixel location; (2) application of the knowledge of tissue thickness to calculate an edge-corrected optical image from the ac signal image. The measurements were conducted with a light mammography apparatus (LIMA) designed for feasibility tests in the clinical environment. Operating in the frequency-domain (110 MHz), this instrument performs a transillumination optical scan at two wavelengths (685 and 825 nm). We applied the proposed two-step procedure to data from breast phantoms and from human breasts. The processed images provide higher contrast and detectability in optical mammography with respect to raw data breast images.

  6. Extending the Effective Ranging Depth of Spectral Domain Optical Coherence Tomography by Spatial Frequency Domain Multiplexing

    Directory of Open Access Journals (Sweden)

    Tong Wu

    2016-11-01

    Full Text Available We present a spatial frequency domain multiplexing method for extending the imaging depth range of a spectral domain optical coherence tomography (SDOCT system without any expensive device. This method uses two galvo scanners with different pivot-offset distances in two independent reference arms for spatial frequency modulation and multiplexing. The spatial frequency contents corresponding to different depth regions of the sample can be shifted to different frequency bands. The spatial frequency domain multiplexing SDOCT system provides an approximately 1.9-fold increase in the effective ranging depth compared with that of a conventional full-range SDOCT system. The reconstructed images of phantom and biological tissue demonstrate the expected increase in ranging depth. The parameters choice criterion for this method is discussed.

  7. Compact optical processor for Hough and frequency domain features

    Science.gov (United States)

    Ott, Peter

    1996-11-01

    Shape recognition is necessary in a broad band of applications such as traffic sign or work piece recognition. It requires not only neighborhood processing of the input image pixels but global interconnection of them. The Hough transform (HT) performs such a global operation and it is well suited in the preprocessing stage of a shape recognition system. Translation invariant features can be easily calculated form the Hough domain. We have implemented on the computer a neural network shape recognition system which contains a HT, a feature extraction, and a classification layer. The advantage of this approach is that the total system can be optimized with well-known learning techniques and that it can explore the parallelism of the algorithms. However, the HT is a time consuming operation. Parallel, optical processing is therefore advantageous. Several systems have been proposed, based on space multiplexing with arrays of holograms and CGH's or time multiplexing with acousto-optic processors or by image rotation with incoherent and coherent astigmatic optical processors. We took up the last mentioned approach because 2D array detectors are read out line by line, so a 2D detector can achieve the same speed and is easier to implement. Coherent processing can allow the implementation of tilers in the frequency domain. Features based on wedge/ring, Gabor, or wavelet filters have been proven to show good discrimination capabilities for texture and shape recognition. The astigmatic lens system which is derived form the mathematical formulation of the HT is long and contains a non-standard, astigmatic element. By methods of lens transformation s for coherent applications we map the original design to a shorter lens with a smaller number of well separated standard elements and with the same coherent system response. The final lens design still contains the frequency plane for filtering and ray-tracing shows diffraction limited performance. Image rotation can be done

  8. A distributed fiber optic sensor system for dike monitoring using Brillouin optical frequency domain analysis

    Science.gov (United States)

    Nöther, Nils; Wosniok, Aleksander; Krebber, Katerina; Thiele, Elke

    2008-03-01

    We report on the development of a complete system for spatially resolved detection of critical soil displacement in river embankments. The system uses Brillouin frequency domain analysis (BOFDA) for distributed measurement of strain in silica optical fibers. Our development consists of the measurement unit, an adequate coating for the optical fibers and a technique to integrate the coated optical fibers into geotextiles as they are commonly used in dike construction. We present several laboratory and field tests that prove the capability of the system to detect areas of soil displacement as small as 2 meters. These are the first tests of truly distributed strain measurements on optical fibers embedded into geosynthetics.

  9. Optical frequency domain reflectometry: principles and applications in fiber optic sensing

    Science.gov (United States)

    Kreger, Stephen T.; Rahim, Nur Aida Abdul; Garg, Naman; Klute, Sandra M.; Metrey, Daniel R.; Beaty, Noah; Jeans, James W.; Gamber, Robert

    2016-05-01

    Optical Frequency Domain Reflectometry (OFDR) is the basis of an emerging high-definition distributed fiber optic sensing (HD-FOS) technique that provides an unprecedented combination of resolution and sensitivity. OFDR employs swept laser interferometry to produce strain or temperature vs. sensor length with fiber Bragg gratings (FBGs) or Rayleigh scatter as the source signal. We look at the influence of HD-FOS on design and test of new, lighter weight, stronger and more fuel efficient vehicles. Examples include defect detection, model verification and structural health monitoring of composites, and temperature distribution monitoring of battery packs and inverters in hybrid and electric powertrains.

  10. Microball lens integrated fiber probe for optical frequency domain imaging

    Institute of Scientific and Technical Information of China (English)

    Jae-Ho Han; J.U.Kang

    2011-01-01

    An integrated microball lens fiber catheter probe is demonstrated, which has better lateral resolution and longer working distance than a corresponding bare fiber probe with diverging beam for Fourier domain optical coherence tomography (FDOCT). Simulation results are shown to gain the effect of the distance between the microball lens and the bare fiber to the focusing plane and beam width. The freedom of modifying the working distance and lateral resolution is shown. This is achieved by changing the gap distance between the single-mode fiber and the microball lens within the packaged surgical needle catheter without using an additional beam expander having a fixed length. The probe successfully acquired cross-sectional images of ocular tissues from an animal sample with the proposed miniaturized imaging probe.%@@ An integrated microball lens fiber catheter probe is demonstrated,which has better lateral resolution and longer working distance than a corresponding bare fiber probe with diverging beam for Fourier domain optical coherence tomography(FDOCT).Simulation results are shown to gain the effect of the distance between the microball lens and the bare fiber to the focusing plane and beam width.The freedom of modifying the working distance and lateral resolution is shown.This is achieved by changing the gap distance between the single-mode fiber and the microball lens within the packaged surgical needle catheter without using an additional beam expander having a fixed length.The probe successfully acquired crosssectional images of ocular tissues from an animal sample with the proposed miniaturized imaging probe.

  11. High-Speed Microscale Optical Tracking Using Digital Frequency-Domain Multiplexing

    OpenAIRE

    MacLachlan, Robert A.; Riviere, Cameron N.

    2009-01-01

    Position-sensitive detectors (PSDs), or lateral-effect photodiodes, are commonly used for high-speed, high-resolution optical position measurement. This paper describes the instrument design for multidimensional position and orientation measurement based on the simultaneous position measurement of multiple modulated sources using frequency-domain-multiplexed (FDM) PSDs. The important advantages of this optical configuration in comparison with laser/mirror combinations are that it has a large ...

  12. High-Speed Microscale Optical Tracking Using Digital Frequency-Domain Multiplexing

    OpenAIRE

    MacLachlan, Robert A.; Riviere, Cameron N.

    2009-01-01

    Position-sensitive detectors (PSDs), or lateral-effect photodiodes, are commonly used for high-speed, high-resolution optical position measurement. This paper describes the instrument design for multidimensional position and orientation measurement based on the simultaneous position measurement of multiple modulated sources using frequency-domain-multiplexed (FDM) PSDs. The important advantages of this optical configuration in comparison with laser/mirror combinations are that it has a large ...

  13. Frequency and time domain analysis of an external cavity laser with strong filtered optical feedback

    DEFF Research Database (Denmark)

    Detoma, Enrico; Tromborg, Bjarne; Montrosset, Ivo

    -signal analysis in the frequency domain allows a calculation of the range of operation without mode hopping around the grating reflectivity peak. This region should be as large as possible for proper operation of the tunable laser source. The analysis shows this stabilizing effect of mode coupling and gain......The stability properties of an external cavity laser with strong grating-filtered optical feedback to an anti-reflection coated facet are studied with a general frequency domain model. The model takes into account non-linear effects like four wave mixing and gain compression. A small...... copression in the lasing mode. An integral equation for the electrical field is derived from the frequency domain model and used for time domain simulations of large-signal behavior....

  14. Towards spatial frequency domain optical imaging of neurovascular coupling in a mouse model of Alzheimer's disease

    Science.gov (United States)

    Lin, Alexander J.; Konecky, Soren D.; Rice, Tyler B.; Green, Kim N.; Choi, Bernard; Durkin, Anthony J.; Tromberg, Bruce J.

    2012-02-01

    Early neurovascular coupling (NVC) changes in Alzheimer's disease can potentially provide imaging biomarkers to assist with diagnosis and treatment. Previous efforts to quantify NVC with intrinsic signal imaging have required assumptions of baseline optical pathlength to calculate changes in oxy- and deoxy-hemoglobin concentrations during evoked stimuli. In this work, we present an economical spatial frequency domain imaging (SFDI) platform utilizing a commercially available LED projector, camera, and off-the-shelf optical components suitable for imaging dynamic optical properties. The fast acquisition platform described in this work is validated on silicone phantoms and demonstrated in neuroimaging of a mouse model.

  15. Brain connectivity study of joint attention using frequency-domain optical imaging technique

    Science.gov (United States)

    Chaudhary, Ujwal; Zhu, Banghe; Godavarty, Anuradha

    2010-02-01

    Autism is a socio-communication brain development disorder. It is marked by degeneration in the ability to respond to joint attention skill task, from as early as 12 to 18 months of age. This trait is used to distinguish autistic from nonautistic populations. In this study, diffuse optical imaging is being used to study brain connectivity for the first time in response to joint attention experience in normal adults. The prefrontal region of the brain was non-invasively imaged using a frequency-domain based optical imager. The imaging studies were performed on 11 normal right-handed adults and optical measurements were acquired in response to joint-attention based video clips. While the intensity-based optical data provides information about the hemodynamic response of the underlying neural process, the time-dependent phase-based optical data has the potential to explicate the directional information on the activation of the brain. Thus brain connectivity studies are performed by computing covariance/correlations between spatial units using this frequency-domain based optical measurements. The preliminary results indicate that the extent of synchrony and directional variation in the pattern of activation varies in the left and right frontal cortex. The results have significant implication for research in neural pathways associated with autism that can be mapped using diffuse optical imaging tools in the future.

  16. Note: A simple broad bandwidth undersampling frequency-domain digital diffuse optical spectroscopy system

    Science.gov (United States)

    Jung, Justin; Istfan, Raeef; Roblyer, Darren

    2014-07-01

    Near-Infrared frequency-domain technologies, such as Diffuse Optical Spectroscopy (DOS), have demonstrated growing potential in a number of clinical applications. The broader dissemination of this technology is limited by the complexity and cost of instrumentation. We present here a simple system constructed with off-the-shelf components that utilizes undersampling for digital frequency-domain dDOS measurements. Broadband RF sweeps (50-300 MHz) were digitally sampled at 25 MSPS; amplitude, phase, and optical property extractions were within 5% of network analyzer derived values. The use of undersampling for broad bandwidth dDOS provides a significant reduction in complexity, power consumption, and cost compared with high-speed ADCs and analog techniques.

  17. Phase Analysis for Frequency Standards in the Microwave and Optical Domains.

    Science.gov (United States)

    Kazda, Michael; Gerginov, Vladislav; Huntemann, Nils; Lipphardt, Burghard; Weyers, Stefan

    2016-07-01

    Coherent manipulation of atomic states is a key concept in high-precision spectroscopy and used in atomic fountain clocks and a number of optical frequency standards. Operation of these standards can involve a number of cyclic switching processes, which may induce cycle-synchronous phase excursions of the interrogation signal and thus lead to shifts in the output of the frequency standard. We have built a field-programmable gate array (FPGA)-based phase analyzer to investigate these effects and conducted measurements on two kinds of frequency standards. For the caesium fountains PTB-CSF1 and PTB-CSF2, we were able to exclude phase variations of the microwave source at the level of a few microradians, corresponding to relative frequency shifts of less than [Formula: see text]. In the optical domain, we investigated phase variations in PTB's Yb (+) optical frequency standard and made detailed measurements of acousto-optic modulator (AOM) chirps and their scaling with duty cycle and driving power. We ascertained that cycle-synchronous as well as long-term phase excursion do not cause frequency shifts larger than [Formula: see text].

  18. Real-time frequency-domain fiber optic sensor for intra-arterial blood oxygen measurements

    Science.gov (United States)

    Alcala, J. R.; Scott, Ian L.; Parker, Jennifer W.; Atwater, Beauford W.; Yu, Clement; Fischer, Russell; Bellingrath, K.

    1993-05-01

    A real time frequency domain phosphorimeter capable of measuring precise and accurate excited state lifetimes for determining oxygen is described. This frequency domain instrument does not make use of cross correlation techniques traditionally used in frequency domain fluorometers. Instead, the electrical signal from the detector is filtered to contain only the first several harmonics. This filtered signal is then sampled and averaged over a few thousand cycles. The absolute phase and absolute modulation of each sampled harmonic of the excitation and of the luminescence is computed by employing fast Fourier transform algorithms. The phase delay and the modulation ratio is then calculated at each harmonic frequency. A least squares fit is performed in the frequency domain to obtain the lifetimes of discrete exponentials. Oxygen concentrations are computed from these lifetimes. Prototypes based on these techniques were built employing commercially available components. Results from measurements in saline solution and in the arterial blood of dogs show that oxygen concentrations can be determined reproducibly. The system drift is less than 1% in over 100 hours of continuous operation. The performance of fiber optic sensors was evaluated in dogs over a period of 10 hours. The sensors tracked changes in arterial oxygen tension over the course of the experiment without instabilities. The overall response of the system was about 90 seconds. The update time was 3 seconds.

  19. Linear systems modeling of adaptive optics in the spatial-frequency domain.

    Science.gov (United States)

    Ellerbroek, Brent L

    2005-02-01

    Spatial-frequency domain techniques have traditionally been applied to obtain estimates for the independent effects of a variety of individual error sources in adaptive optics (AO). Overall system performance is sometimes estimated by introducing the approximation that these individual error terms are statistically independent, so that their magnitudes may be summed in quadrature. More accurate evaluation methods that account for the correlations between the individual error sources have required Monte Carlo simulations or large matrix calculations that can take much longer to compute, particularly as the order of the AO system increases beyond a few hundred degrees of freedom. We describe an approach to evaluating AO system performance in the spatial-frequency domain that is relatively computationally efficient but still accounts for many of the interactions between the fundamental error sources in AO. We exploit the fact that (in the limits of an infinite aperture and geometrical optics) all the basic wave-front propagation, sensing, and correction processes that describe the behavior of an AO system are spatial-filtering operations in the Fourier domain. Essentially all classical wave-front control algorithms and evaluation formulas are expressed in terms of these filters and may therefore be evaluated one spatial-frequency component at a time. Performance estimates for very-high-order AO systems may be obtained in 1 to 2 orders of magnitude less time than needed when detailed simulations or analytical models in the spatial domain are used, with a relative discrepancy of 5% to 10% for typical sample problems.

  20. Long-range vibration sensor based on correlation analysis of optical frequency-domain reflectometry signals.

    Science.gov (United States)

    Ding, Zhenyang; Yao, X Steve; Liu, Tiegen; Du, Yang; Liu, Kun; Han, Qun; Meng, Zhuo; Chen, Hongxin

    2012-12-17

    We present a novel method to achieve a space-resolved long- range vibration detection system based on the correlation analysis of the optical frequency-domain reflectometry (OFDR) signals. By performing two separate measurements of the vibrated and non-vibrated states on a test fiber, the vibration frequency and position of a vibration event can be obtained by analyzing the cross-correlation between beat signals of the vibrated and non-vibrated states in a spatial domain, where the beat signals are generated from interferences between local Rayleigh backscattering signals of the test fiber and local light oscillator. Using the proposed technique, we constructed a standard single-mode fiber based vibration sensor that can have a dynamic range of 12 km and a measurable vibration frequency up to 2 kHz with a spatial resolution of 5 m. Moreover, preliminarily investigation results of two vibration events located at different positions along the test fiber are also reported.

  1. Control of polarization signal distortion by frequency domain phase conjugation in optical fiber systems

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Optical frequency domain phase conjugation(FDPC) is based on phase conjuga-tion of spectrum of an input signal.It is equivalent to the phase conjugation and the time reversal of the temporal envelope of an input signal.The use of FDPC to con-trol polarization signal distortion in birefringent optical fiber systems is proposed.Evolution of polarization signals in the system using midway FDPC is analyzed theoretically and simulated numerically.It is shown that the distortion of polariza-tion signals can be controlled effectively by FDPC.The impairments due to disper-sion and nonlinear effects can be suppressed simultaneously.

  2. Control of polarization signal distortion by frequency domain phase conjusation in optical fiber systems

    Institute of Scientific and Technical Information of China (English)

    BU Yang; WANG XiangZhao

    2008-01-01

    Optical frequency domain phase conjugation (FDPC) is based on phase conjugation of spectrum of an input signal. It is equivalent to the phase conjugation and the time reversal of the temporal envelope of an input signal. The use of FDPC to con-trol polarization signal distortion in birefringent optical fiber systems is proposed. Evolution of polarization signals in the system using midway FDPC is analyzed theoretically and simulated numerically. It is shown that the distortion of polariza-tion signals can be controlled effectively by FDPC. The impairments due to disper-sion and nonlinear effects can be suppressed simultaneously.

  3. Phase Analysis for Frequency Standards in the Microwave and Optical Domains

    CERN Document Server

    Kazda, M; Huntemann, N; Lipphardt, B; Weyers, S

    2015-01-01

    Coherent manipulation of atomic states is a key concept in high-precision spectroscopy and used in atomic fountain clocks and a number of optical frequency standards. Operation of these standards can involve a number of cyclic switching processes, which may induce cycle synchronous phase excursions of the interrogation signal and thus lead to shifts in the output of the frequency standard. We have built a FPGA-based phase analyzer to investigate these effects and conducted measurements on two frequency standards. For the caesium fountain PTB-CSF2 we were able to exclude phase variations of the microwave source at the level of a few $\\mu$rad, corresponding to relative frequency shifts of less than 10$^{-16}$. In the optical domain, we investigated phase variations in PTB's Yb$^+$ optical frequency standard and made detailed measurements of AOM chirps and their scaling with duty cycle and driving power. We ascertained that cycle-synchronous as well as long-term phase excursion do not cause frequency shifts larg...

  4. Spatial-Resolution Improvement in Optical Frequency Domain Reflectometry System Based on Tunable Linear Fiber Laser

    Energy Technology Data Exchange (ETDEWEB)

    Li Guoyu; Li Yan [Institute of Information Engineering, Handan College, Handan, 056005 (China); Zhao Peng, E-mail: guoyu_li@yahoo.cn [School of Physics and Optoelectronic Engineering, Dalian University of Technology, Dalian 116024 (China)

    2011-02-01

    In optical frequency domain reflectometry (OFDR) system, the spatial resolution is obtained by using the total frequency-sweep span of the tunable laser. However, in practice, the spatial resolution is severely limited by nonlinearity in the lightwave-frequency sweep of the tunable laser. A closed-loop PZT modulated DBR linear fiber laser is proposed to improve the spatial resolution of the OFDR system. Experimental results show that the spatial resolution of OFDR system has improved greatly. When the frequency sweep excursion is 66GHz and the fiber under test (FUT) is 7 m, the OFDR system has a spatial resolution of 1.5 m with open-loop PZT modulated laser. But the spatial resolution increases to 35 cm with closed-loop PZT modulated laser.

  5. Coherent optical time domain reflectometry by logarithmic detection and timed random frequency hopping

    Science.gov (United States)

    Lu, Lidong; Sun, Xiaoyan; Bu, Xiande; Li, Binglin

    2017-02-01

    A scheme using timed random frequency hopping and signal logarithmic mean method is proposed and experimentally demonstrated in a coherent optical time domain reflectometry (OTDR) system to reduce the fading noise of the OTDR trace and simplify the signal processing procedure. The timed random frequency hopping is realized by randomly changing the driving current of the laser at certain time points. By this method, the fading noise of OTDR trace can be reduced to be 1/5 of that without using it. Also, a radio frequency power detector (RFPD), whose output voltage has linear relationship with the input logarithmic RF power, is used to extract the power of the RF signals from the balanced photodetector. Then, a data acquisition card directly captures and adds the digital voltage signals from the RFPD to reduce the fading noise and improve the measurement dynamic range. Compared with synchronous and asynchronous frequency hopping scheme, the proposed method is of high efficiency.

  6. Effects of laser frequency drift in phase-sensitive optical time-domain reflectometry fiber sensors

    CERN Document Server

    Zhirnov, Andrey; Stepanov, Konstantin; Nesterov, Evgeny; Karasik, Valery; Svelto, Cesare; Pnev, Alexey

    2016-01-01

    The present work studies the influence of laser frequency drifts on operating of phase-sensitive optical time-domain reflectometry ($\\Phi$-OTDR) fiber sensors. A mathematical model and numerical simulations are employed to highlight the influence of frequency drifts of light sources on two characteristic scales: large-time (minutes) and short-time (milliseconds) frequency drifts. Numerical simulation results are compared with predictions given by the fluctuation ratio coefficient (FRC), and they are in a qualitative agreement. In addition to qualitative criteria for light sources given by the FRC, quantitive requirements for optimal light sources for $\\Phi$-OTDR sensors are obtained. Numerical simulation results are verified by comparison with experimental data for three significantly different types of light source.

  7. Transformation optics: a time- and frequency-domain analysis of electron-energy loss spectroscopy

    CERN Document Server

    Kraft, Matthias; Pendry, J B

    2016-01-01

    Electron energy loss spectroscopy (EELS) and Cathodoluminescence (CL) play a pivotal role in many of the cutting edge experiments in plasmonics. EELS and CL experiments are usually supported by numerical simulations, which, whilst accurate, may not provide as much physical insight as analytical calculations do. Fully analytical solutions to EELS and CL systems in plasmonics are rare and difficult to obtain. This paper aims to narrow this gap by introducing a new method based on Transformation optics that allows to calculate the quasi-static frequency and time-domain response of plasmonic particles under electron beam excitation.

  8. Frequency-Domain Chromatic Dispersion Equalization Using Overlap-Add Methods in Coherent Optical System

    CERN Document Server

    Xu, Tianhua; Popov, Sergei; Forzati, Marco; Martensson, Jonas; Mussolin, Marco; Li, Jie; Wang, Ke; Zhang, Yimo; Friberg, Ari T

    2016-01-01

    The frequency domain equalizers (FDEs) employing two types of overlap-add zero-padding (OLA-ZP) methods are applied to compensate the chromatic dispersion in a 112-Gbit/s non-return-to-zero polarization division multiplexed quadrature phase shift keying (NRZ-PDM-QPSK) coherent optical transmission system. Simulation results demonstrate that the OLA-ZP methods can achieve the same acceptable performance as the overlap-save method. The required minimum overlap (or zero-padding) in the FDE is derived, and the optimum fast Fourier transform length to minimize the computational complexity is also analyzed.

  9. Frequency domain optical tomography using a conjugate gradient method without line search

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyun Keol [Departement des Sciences Appliquees, Universite du Quebec a Chicoutimi, 555 Boulevard de l' Universite, P4-3240, Chicoutimi, Quebec, G7H 2B1 (Canada); Charette, Andre [Departement des Sciences Appliquees, Universite du Quebec a Chicoutimi, 555 Boulevard de l' Universite, P4-3240, Chicoutimi, Quebec, G7H 2B1 (Canada)]. E-mail: andre_charette@uqac.ca

    2007-03-15

    A conjugate gradient method without line search (CGMWLS) is presented. This method is used to retrieve the local maps of absorption and scattering coefficients inside the tissue-like test medium, with the synthetic data. The forward problem is solved with a discrete-ordinates finite-difference method based on the frequency domain formulation of radiative transfer equation. The inversion results demonstrate that the CGMWLS can retrieve simultaneously the spatial distributions of optical properties inside the medium within a reasonable accuracy, by reducing cross-talk between absorption and scattering coefficients.

  10. High-Speed Microscale Optical Tracking Using Digital Frequency-Domain Multiplexing.

    Science.gov (United States)

    Maclachlan, Robert A; Riviere, Cameron N

    2009-06-01

    Position-sensitive detectors (PSDs), or lateral-effect photodiodes, are commonly used for high-speed, high-resolution optical position measurement. This paper describes the instrument design for multidimensional position and orientation measurement based on the simultaneous position measurement of multiple modulated sources using frequency-domain-multiplexed (FDM) PSDs. The important advantages of this optical configuration in comparison with laser/mirror combinations are that it has a large angular measurement range and allows the use of a probe that is small in comparison with the measurement volume. We review PSD characteristics and quantitative resolution limits, consider the lock-in amplifier measurement system as a communication link, discuss the application of FDM to PSDs, and make comparisons with time-domain techniques. We consider the phase-sensitive detector as a multirate DSP problem, explore parallels with Fourier spectral estimation and filter banks, discuss how to choose the modulation frequencies and sample rates that maximize channel isolation under design constraints, and describe efficient digital implementation. We also discuss hardware design considerations, sensor calibration, probe construction and calibration, and 3-D measurement by triangulation using two sensors. As an example, we characterize the resolution, speed, and accuracy of an instrument that measures the position and orientation of a 10 mm × 5 mm probe in 5 degrees of freedom (DOF) over a 30-mm cube with 4-μm peak-to-peak resolution at 1-kHz sampling.

  11. Accelerating frequency-domain diffuse optical tomographic image reconstruction using graphics processing units.

    Science.gov (United States)

    Prakash, Jaya; Chandrasekharan, Venkittarayan; Upendra, Vishwajith; Yalavarthy, Phaneendra K

    2010-01-01

    Diffuse optical tomographic image reconstruction uses advanced numerical models that are computationally costly to be implemented in the real time. The graphics processing units (GPUs) offer desktop massive parallelization that can accelerate these computations. An open-source GPU-accelerated linear algebra library package is used to compute the most intensive matrix-matrix calculations and matrix decompositions that are used in solving the system of linear equations. These open-source functions were integrated into the existing frequency-domain diffuse optical image reconstruction algorithms to evaluate the acceleration capability of the GPUs (NVIDIA Tesla C 1060) with increasing reconstruction problem sizes. These studies indicate that single precision computations are sufficient for diffuse optical tomographic image reconstruction. The acceleration per iteration can be up to 40, using GPUs compared to traditional CPUs in case of three-dimensional reconstruction, where the reconstruction problem is more underdetermined, making the GPUs more attractive in the clinical settings. The current limitation of these GPUs in the available onboard memory (4 GB) that restricts the reconstruction of a large set of optical parameters, more than 13,377.

  12. Frequency domain laser ultrasonics: Optical transduction of acoustic waves and nanomechanical devices

    Science.gov (United States)

    Bramhavar, Suraj

    The concept of optical excitation and detection of nanoscale mechanical motion has led to a variety of tools for non-destructive materials characterization and remote sensing. These techniques, commonly referred to as laser ultrasonics, offer the benefit of high-bandwidth, highly localized measurements, and also allow for the ability to investigate nanoscale devices. The impact of laser ultrasonic systems has been felt in industries ranging from semiconductor metrology to biological and chemical sensing. In this thesis, we develop a variety of techniques utilizing a frequency domain laser ultrasonic approach, where amplitude modulated continuous wave laser light is used instead of traditional pulsed laser sources, and we apply these systems in free-space, optical fiber based, and integrated on-chip configurations. In doing so, we demonstrate the ability to efficiently transduce various types of mechanical motion including surface and bulk acoustic waves, guided acoustic waves, and resonant motion from nanomechanical systems (NEMS). First, we develop a superheterodyne free-space ultrasonic inspection system in an effort to characterize surface acoustic wave dispersion in thin-film material systems. We utilize a similar system to study negative refraction and focusing behavior of guided elastic waves in a thin metal plate, providing a novel approach for the study of negative index physics. Furthermore, we develop a near-field optical technique using optical fibers to simultaneously transduce the motion of 70 NEMS resonators using a single channel. This multiplexed approach serves as a crucial step in moving NEMS technology out of the research laboratory. Finally, we go on to study opto-mechanical interactions between optical whispering gallery mode (WGM) resonators and integrated NEMS devices on the same chip, using the enhanced interactions to study optical forces acting on the nanoscale mechanical devices. This integrated system provides a very efficient mechanical

  13. Time-and-frequency domains approach to data processing in multiwavelength optical scatterometry of dielectric gratings

    KAUST Repository

    Granet, Gérard

    2013-01-01

    This paper focuses on scatterometry problems arising in lithography production of periodic gratings. Namely, the paper introduces a theoretical and numerical-modeling-oriented approach to scatterometry problems and discusses its capabilities. The approach allows for reliable detection of deviations in gratings\\' critical dimensions (CDs) during the manufacturing process. The core of the approach is the one-to-one correspondence between the electromagnetic (EM) characteristics and the geometric/material properties of gratings. The approach is based on highly accurate solutions of initial boundary-value problems describing EM waves\\' interaction on periodic gratings. The advantage of the approach is the ability to perform simultaneously and interactively both in frequency and time domains under conditions of possible resonant scattering of EM waves by infinite or finite gratings. This allows a detection of CDs for a wide range of gratings, and, thus is beneficial for the applied scatterometry. (C) 2013 Optical Society of America

  14. Real-time frequency domain temperature and oxygen sensor with a single optical fiber.

    Science.gov (United States)

    Liao, S C; Xu, Z; Izatt, J A; Alcala, J R

    1997-11-01

    The combined excited-state phosphorescence life-times of an alexandrite crystal and platinum tetraphenylporphyrin Pt(TPP) in a single-fiber sensor are used to monitor temperature and oxygen concentration in the physiological range from 15-45 degrees C and 0-50% O2 with precision of 0.24 degree C and 0.15% O2 and accuracy of 0.28 degree C and 0.2% O2. A 500-micron cubic alexandrite crystal bound to the distal end of a 750-micron-diameter optical fiber core and the Pt(TPP) coated circumferentially with a length of 1 cm from the end of the same fiber are excited with pulsed super-bright blue LED light. This apparatus uses a 125-kHz sampler for data acquisition and frequency domain methods for signal processing. The instrument amplifies both the dc and ac components of the photomultiplier output and band limits the signal to 20 kHz. The fundamental frequency of the excitation is set to 488.3 Hz and the highest harmonic used is the 35th. This bandlimited signal is sampled and averaged over a few hundred cycles in the time domain. The frequency domain representation of the data is obtained by employing fast Fourier transform algorithms. The phase delay and the modulation ratio of each sampled harmonic are then computed. At least four log-spaced harmonic phases or modulations are averaged before decoding the two lifetimes of temperature and oxygen phosphorescent sensors. A component of zero lifetime is introduced to account for the excitation backscatter leakage through optical interference filters seen by the photodetector. Linear and second-order empirical polynomials are employed to compute the temperatures and oxygen concentrations from the inverse lifetimes. In the situation of constant oxygen concentration, the lifetime of Pt(TPP) changes with temperature but can be compensated using the measured temperature lifetime. The system drift is 0.24 degree C for the temperature measurement and 0.59% for the oxygen concentration measurement over 30 h of continuous operation

  15. Zero-guard-interval coherent optical OFDM with overlapped frequency-domain CD and PMD equalization.

    Science.gov (United States)

    Chen, Chen; Zhuge, Qunbi; Plant, David V

    2011-04-11

    This paper presents a new channel estimation/equalization algorithm for coherent OFDM (CO-OFDM) digital receivers, which enables the elimination of the cyclic prefix (CP) for OFDM transmission. We term this new system as the zero-guard-interval (ZGI)-CO-OFDM. ZGI-CO-OFDM employs an overlapped frequency-domain equalizer (OFDE) to compensate both chromatic dispersion (CD) and polarization mode dispersion (PMD) before the OFDM demodulation. Despite the zero CP overhead, ZGI-CO-OFDM demonstrates a superior PMD tolerance than the previous reduced-GI (RGI)-CO-OFDM, which is verified under several different PMD conditions. Additionally, ZGI-CO-OFDM can improve the channel estimation accuracy under high PMD conditions by using a larger intra-symbol frequency-averaging (ISFA) length as compared to RGI-CO-OFDM. ZGI-CO-OFDM also enables the use of ever smaller fast Fourier transform (FFT) sizes (i.e. OFDM. We show that ZGI-CO-OFDM requires reasonably small additional computation effort (~13.6%) compared to RGI-CO-OFDM for 112-Gb/s transmission over a 1600-km dispersion-uncompensated optical link.

  16. Spatially-dense, multi-spectral, frequency-domain diffuse optical tomography of breast cancer

    Science.gov (United States)

    Ban, Han Yong

    Diffuse optical tomography (DOT) employs near-infrared light to image the concentration of chromophores and cell organelles in tissue and thereby providing access to functional parameters that can differentiate cancerous from normal tissues. This thesis describes research at the bench and in the clinic that explores and identifies the potential of DOT breast cancer imaging. The bench and clinic instrumentation differ but share important features: they utilize a very large, spatially dense, set of source-detector pairs (10 7) for imaging in the parallel-plate geometry. The bench experiments explored three-dimensional (3D) image resolution and fidelity as a function of numerous parameters and also ascertained the effects of a chest wall phantom. The chest wall is always present but is typically ignored in breast DOT. My experiments clarified chest wall influences and developed schemes to mitigate these effects. Mostly, these schemes involved selective data exclusion, but their efficacy also depended on reconstruction approach. Reconstruction algorithms based on analytic (fast) Fourier inversion and linear algebraic techniques were explored. The clinical experiments centered around a DOT instrument that I designed, constructed, and have begun to test (in-vitro and in-vivo). This instrumentation offers many features new to the field. Specifically, the imager employs spatially-dense, multi-spectral, frequency-domain data; it possesses the world's largest optical source-detector density yet reported, facilitated by highly-parallel CCD-based frequency-domain imaging based on gain-modulation heterodyne detection. The instrument thus measures both phase and amplitude of the diffusive light waves. Other features include both frontal and sagittal breast imaging capabilities, ancillary cameras for measurement of breast boundary profiles, real-time data normalization, and mechanical improvements for patient comfort. The instrument design and construction is my most significant

  17. Evaluating the thermal stability of multi-pass cells' effective optical path length using optical frequency domain reflectometer

    Science.gov (United States)

    Gao, Hong; Cao, Xiuhan; Li, Jinyi; Du, Zhenhui

    2016-10-01

    Multi-pass cells (MPCs) are commonly used to improve the sensitivity for trace gas detection using spectroscopy technologies. The determination of Effective Optical Path Length (EOPL) of a MPC is very important and challenging in applications which aim at absolute measurements. It is well-known that the temperature changing will exercise some influence on the MPCs' spatial structure, however, measurements of the influence haven't been reported which might due to the limitation of measuring method. In this paper, we used a direct high-precision measuring method with Optical Frequency Domain Reflectometer (OFDR) to evaluate the thermal stability of a multi-pass cell. To simulate the environment with a large range of temperature changing, this paper gave a series of experiments by setting the temperature control unit in system from 25 to 175 degree Celsius, and the MPC's EOPL was measured simultaneously for the investigation of temperature response. The results showed that the effective optical path length increase monotonically along with the variation of the temperature, and the rising rate is 0.5 mm/ºC with the total length of about 3 meters which should be pay attention to when the ultra-high accuracy results are demanded. To stabilize the EOPL of the system, if it is possible, the environment temperature of gas cell can be controlled with a constant temperature. In practical applications, the real-time monitoring of EOPL with a direct measuring method may be necessary.

  18. Pragmatic circuits frequency domain

    CERN Document Server

    Eccles, William

    2006-01-01

    Pragmatic Circuits: Frequency Domain goes through the Laplace transform to get from the time domain to topics that include the s-plane, Bode diagrams, and the sinusoidal steady state. This second of three volumes ends with a-c power, which, although it is just a special case of the sinusoidal steady state, is an important topic with unique techniques and terminology. Pragmatic Circuits: Frequency Domain is focused on the frequency domain. In other words, time will no longer be the independent variable in our analysis. The two other volumes in the Pragmatic Circuits series include titles on DC

  19. Advanced demodulation technique for the extraction of tissue optical properties and structural orientation contrast in the spatial frequency domain

    Science.gov (United States)

    Nadeau, Kyle P.; Durkin, Anthony J.; Tromberg, Bruce J.

    2014-05-01

    We have developed a method for extracting spatial frequency information content from biological tissue, which is used to calculate tissue optical properties and determine tissue structural orientation. This demodulation method employs a two-dimensional Hilbert transform using a spiral phase function in Fourier space. The approach presented here allows for the determination of tissue optical properties using a single frame of data for each modulation frequency, increasing imaging speed by two to threefold versus conventional, three-phase spatial frequency domain imaging (SFDI). This new single-phase Hilbert transform approach recovers optical property and scattering orientation index values within 1% and 10% of three-phase SFDI, respectively. These results suggest that, using the Hilbert demodulation technique, SFDI data acquisition speed can be increased significantly while preserving data quality, which will help us move forward toward the implementation of a real-time SFDI platform.

  20. Non-invasive optical monitoring of the newborn piglet brain using continuous-wave and frequency-domain spectroscopy

    Science.gov (United States)

    Fantini, Sergio; Hueber, Dennis; Franceschini, Maria Angela; Gratton, Enrico; Rosenfeld, Warren; Stubblefield, Phillip G.; Maulik, Dev; Stankovic, Miljan R.

    1999-06-01

    We have used continuous-wave (CW) and frequency-domain spectroscopy to investigate the optical properties of the newborn piglet brain in vivo and non-invasively. Three anaesthetized, intubated, ventilated and instrumented newborn piglets were placed into a stereotaxic instrument for optimal experimental stability, reproducible probe-to-scalp optical contact and 3D adjustment of the optical probe. By measuring the absolute values of the brain absorption and reduced scattering coefficients at two wavelengths (758 and 830 nm), frequency-domain spectroscopy provided absolute readings (in contrast to the relative readings of CW spectroscopy) of cerebral haemoglobin concentration and saturation during experimentally induced perturbations in cerebral haemodynamics and oxygenation. Such perturbations included a modulation of the inspired oxygen concentration, transient brain asphyxia, carotid artery occlusion and terminal brain asphyxia. The baseline cerebral haemoglobin saturation and concentration, measured with frequency-domain spectroscopy, were about 60% and 42 µM respectively. The cerebral saturation values ranged from a minimum of 17% (during transient brain asphyxia) to a maximum of 80% (during recovery from transient brain asphyxia). To analyse the CW optical data, we have (a) derived a mathematical relationship between the cerebral optical properties and the differential pathlength factor and (b) introduced a method based on the spatial dependence of the detected intensity (dc slope method). The analysis of the cerebral optical signals associated with the arterial pulse and with respiration demonstrates that motion artefacts can significantly affect the intensity recorded from a single optode pair. Motion artefacts can be strongly reduced by combining data from multiple optodes to provide relative readings in the dc slope method. We also report significant biphasic changes (initial decrease and successive increase) in the reduced scattering coefficient measured

  1. Predictors of periprocedural (type IVa) myocardial infarction, as assessed by frequency-domain optical coherence tomography.

    Science.gov (United States)

    Porto, Italo; Di Vito, Luca; Burzotta, Francesco; Niccoli, Giampaolo; Trani, Carlo; Leone, Antonio M; Biasucci, Luigi M; Vergallo, Rocco; Limbruno, Ugo; Crea, Filippo

    2012-02-01

    Frequency-domain optical coherence tomography (FD-OCT) is easily able to define both pre- and post-stenting features of the atherosclerotic plaque that can potentially be related to periprocedural complications. We sought to examine which FD-OCT-defined characteristics, assessed both before and after stent deployment, predicted periprocedural (type IVa) myocardial infarction (MI). FD-OCT was performed before and after coronary stenting in 50 patients undergoing percutaneous coronary intervention (PCI) for either non-ST segment elevation MI (NSTEMI) or stable angina. All patients underwent single-vessel stenting, and only drug-eluting stents were implanted. Troponin T was analyzed on admission, before PCI, and at 12 and 24 hours after PCI, and type IVa MI was defined in stable angina as a rise of at least 3× upper reference limit and in NSTEMI as a pre-PCI troponin T fall, followed by post-PCI troponin T rise >20%. Type IVa MI was diagnosed in 21 patients, while the remaining 29 represented the control group. FD-OCT analysis showed that thin-cap fibroatheroma (76.2% versus 41.4%; P=0.017) prior to PCI, intrastent thrombus (61.9% versus 20.7%; P=0.04), and intrastent dissection (61.9% versus 31%; P=0.03) after PCI were significantly more frequent in type IVa MI than in the control group. Multivariate logistic regression analysis confirmed thin-cap fibroatheroma (OR 29.7, 95% CI 1.4 to 32.1), intrastent thrombus (OR 5.5, CI 1.2 to 24.9) and intrastent dissection (OR 5.3, CI 1.2 to 24.3) as independent predictors of type IVa MI. In conclusion, presence of thin-cap fibroatheroma at pre-PCI FD-OCT and of intrastent thrombus and intrastent dissection at post-PCI FD-OCT predict type IVa MI in a contemporary sample of patients treated with second-generation drug-eluting stents. Interestingly, 2 of the 3 predictors of type IVa MI were not apparent at pre-PCI FD-OCT.

  2. Frequency-domain nonlinear optics in two-dimensionally patterned quasi-phase-matching media

    CERN Document Server

    Phillips, C R; Gallmann, L; Keller, U

    2015-01-01

    Advances in the amplification and manipulation of ultrashort laser pulses has led to revolutions in several areas. Examples include chirped pulse amplification for generating high peak-power lasers, power-scalable amplification techniques, pulse shaping via modulation of spatially-dispersed laser pulses, and efficient frequency-mixing in quasi-phase-matched nonlinear crystals to access new spectral regions. In this work, we introduce and demonstrate a new platform for nonlinear optics which has the potential to combine all of these separate functionalities (pulse amplification, frequency transfer, and pulse shaping) into a single monolithic device. Moreover, our approach simultaneously offers solutions to the performance-limiting issues in the conventionally-used techniques, and supports scaling in power and bandwidth of the laser source. The approach is based on two-dimensional patterning of quasi-phase-matching gratings combined with optical parametric interactions involving spatially dispersed laser pulses...

  3. Frequency-domain analysis of computer-controlled optical surfacing processes

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Mid-high spatial frequency errors are often induced on optical surfaces polished by computer-controlled optical surfacing (CCOS) processes. In order to efficiently remove these errors, which would degrade the performances of optical systems, the ability of a CCOS process to correct the errors have been investigated based on the convolution integral model in view of the availability of material removal. To quantify the ability, some conceptions, such as figure correcting ability and material removal availability (MRA), have been proposed. The research result reveals that the MRA of the CCOS process to correct a single spatial frequency error is determined by its tool removal function (TRF), and it equals the normalized amplitude spectrum of the Fourier transform of its TRF. Finally, three sine surfaces were etched using ion beam figuring (IBF), which is a typical CCOS process. The experimental results have verified the theoretical analysis. The employed method and the conclusions of this work provide a useful mathematical basis to analyze and optimize CCOS processes.

  4. Space-frequency analysis with parallel computing in a phase-sensitive optical time-domain reflectometer distributed sensor.

    Science.gov (United States)

    Hui, Xiaonan; Ye, Taihang; Zheng, Shilie; Zhou, Jinhai; Chi, Hao; Jin, Xiaofeng; Zhang, Xianmin

    2014-10-01

    For a phase-sensitive optical time-domain reflectometer (ϕ-OTDR) distributed sensor system, space-frequency analysis can reduce the false alarm by analyzing the frequency distribution compared with the traditional difference value method. We propose a graphics processing unit (GPU)-based parallel computing method to perform multichannel fast Fourier transform (FFT) and realize the real-time space-frequency analysis. The experiment results show that the time taken by the multichannel FFT decreased considerably based on this GPU parallel computing. The method can be completed with a sensing fiber up to 16 km long and an entry-level GPU. Meanwhile, the GPU can reduce the computing load of the central processing unit from 70% down to less than 20%. We carried out an experiment on a two-point space-frequency analysis, and the results clearly and simultaneously show the vibration point locations and frequency components. The sensor system outputs the real-time space-frequency spectra continuously with a spatial resolution of 16.3 m and frequency resolution of 2.25 Hz.

  5. Detrimental Effect Elimination of Laser Frequency Instability in Brillouin Optical Time Domain Reflectometer by Using Self-Heterodyne Detection

    Directory of Open Access Journals (Sweden)

    Yongqian Li

    2017-03-01

    Full Text Available A useful method for eliminating the detrimental effect of laser frequency instability on Brillouin signals by employing the self-heterodyne detection of Rayleigh and Brillouin scattering is presented. From the analysis of Brillouin scattering spectra from fibers with different lengths measured by heterodyne detection, the maximum usable pulse width immune to laser frequency instability is obtained to be about 4 µs in a self-heterodyne detection Brillouin optical time domain reflectometer (BOTDR system using a broad-band laser with low frequency stability. Applying the self-heterodyne detection of Rayleigh and Brillouin scattering in BOTDR system, we successfully demonstrate that the detrimental effect of laser frequency instability on Brillouin signals can be eliminated effectively. Employing the broad-band laser modulated by a 130-ns wide pulse driven electro-optic modulator, the observed maximum errors in temperatures measured by the local heterodyne and self-heterodyne detection BOTDR systems are 7.9 °C and 1.2 °C, respectively.

  6. Computer-aided classification of rheumatoid arthritis in finger joints using frequency domain optical tomography

    Science.gov (United States)

    Klose, C. D.; Kim, H. K.; Netz, U.; Blaschke, S.; Zwaka, P. A.; Mueller, G. A.; Beuthan, J.; Hielscher, A. H.

    2009-02-01

    Novel methods that can help in the diagnosis and monitoring of joint disease are essential for efficient use of novel arthritis therapies that are currently emerging. Building on previous studies that involved continuous wave imaging systems we present here first clinical data obtained with a new frequency-domain imaging system. Three-dimensional tomographic data sets of absorption and scattering coefficients were generated for 107 fingers. The data were analyzed using ANOVA, MANOVA, Discriminant Analysis DA, and a machine-learning algorithm that is based on self-organizing mapping (SOM) for clustering data in 2-dimensional parameter spaces. Overall we found that the SOM algorithm outperforms the more traditional analysis methods in terms of correctly classifying finger joints. Using SOM, healthy and affected joints can now be separated with a sensitivity of 0.97 and specificity of 0.91. Furthermore, preliminary results suggest that if a combination of multiple image properties is used, statistical significant differences can be found between RA-affected finger joints that show different clinical features (e.g. effusion, synovitis or erosion).

  7. New insights into the coronary artery bifurcation hypothesis-generating concepts utilizing 3-dimensional optical frequency domain imaging.

    Science.gov (United States)

    Farooq, Vasim; Serruys, Patrick W; Heo, Jung Ho; Gogas, Bill D; Okamura, Takayuki; Gomez-Lara, Josep; Brugaletta, Salvatore; Garcìa-Garcìa, Hector M; van Geuns, Robert Jan

    2011-08-01

    Coronary artery bifurcations are a common challenging lesion subset accounting for approximately 10% to 20% of all percutaneous coronary interventions. The provisional T-stenting approach is generally recommended as the first-line management of most lesions. Carina shift is suggested to be the predominant mechanism of side-branch pinching during provisional T-stenting and has been indirectly inferred from bench work and other intravascular imaging modalities. Offline 3-dimensional (3D) reconstructions of patients studied in the first-in-man trial of the high-frequency (160 frames/s) Terumo optical frequency domain imaging system were undertaken using volume-rendering software. Through a series of 3D reconstructions, several novel hypothesis-generating concepts are presented.

  8. Performance limit of a multi-frequency probe based coherent optical time domain reflectometry caused by nonlinear effects

    Institute of Scientific and Technical Information of China (English)

    Lidong Lü; Yuejiang Song; Fan Zhu; Xuping Zhang

    2012-01-01

    The nonlinear effects that limit the performance of the multi-frequency probe (MFP) based coherent optical time domain reflectometry (C-OTDR) are investigated.Based on theoretical analysis and experimental results,compared with conventional C-OTDR,when the probe pulse has power gradient within the pulse width,self-phase modulation (SPM) and cross-phase modulation (XPM) are strengthened in the new COTDR scheme.The generation of four-wave mixing (FWM) is dependent on SPM and XPM,and with modulation frequency of phase modulator higher than 40 MHz,the stimulated Brillouin scattering (SBS) threshold can be enhanced by more than 5 dB,which benefits the maximum dynamic range of the MFP C-OTDR.

  9. A sensitivity function-based conjugate gradient method for optical tomography with the frequency-domain equation of radiative transfer

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyun Keol [Departement des Sciences Appliquees, Universite du Quebec a Chicoutimi, Chicoutimi, Que., G7H 2B1 (Canada); Charette, Andre [Departement des Sciences Appliquees, Universite du Quebec a Chicoutimi, Chicoutimi, Que., G7H 2B1 (Canada)]. E-mail: andre_charette@uqac.ca

    2007-03-15

    The Sensitivity Function-based Conjugate Gradient Method (SFCGM) is described. This method is used to solve the inverse problems of function estimation, such as the local maps of absorption and scattering coefficients, as applied to optical tomography for biomedical imaging. A highly scattering, absorbing, non-reflecting, non-emitting medium is considered here and simultaneous reconstructions of absorption and scattering coefficients inside the test medium are achieved with the proposed optimization technique, by using the exit intensity measured at boundary surfaces. The forward problem is solved with a discrete-ordinates finite-difference method on the framework of the frequency-domain full equation of radiative transfer. The modulation frequency is set to 600 MHz and the frequency data, obtained with the source modulation, is used as the input data. The inversion results demonstrate that the SFCGM can retrieve simultaneously the spatial distributions of optical properties inside the medium within a reasonable accuracy, by significantly reducing a cross-talk between inter-parameters. It is also observed that the closer-to-detector objects are better retrieved.

  10. Analytical investigation of a novel interrogation approach of fiber Bragg grating sensors using Optical Frequency Domain Reflectometry

    Science.gov (United States)

    Yüksel, Kivilcim; Pala, Deniz

    2016-06-01

    This work presents a novel approach in interrogating Polarization Dependent Loss (PDL) of cascaded identical FBGs using Optical Frequency Domain Reflectometer (OFDR). The fundamentals of both polarisation properties of uniform FBGs and polarisation-sensitive OFDR are explained and the benefits of this novel approach in measuring transversal load are discussed. The numerical programs computing the spectral evolution of PDL of the FBGs in the array as a function of grating parameters (grating length and birefringence) are presented. Our simulation results show an excellent agreement with the previously reported simulation (and experimental) results in the literature obtained on a single FBG by using classical state-of-the-art measurement techniques. As an envisaged application, the proposed system shows the feasibility of measuring the residual stresses during manufacturing process of composite materials which is not straightforward by amplitude spectrum measurements and/or considering only the axial strains.

  11. Signal processing method based on group delay calculation for distributed Bragg wavelength shift in optical frequency domain reflectometry.

    Science.gov (United States)

    Wada, Daichi; Igawa, Hirotaka; Murayama, Hideaki; Kasai, Tokio

    2014-03-24

    A signal processing method based on group delay calculations is introduced for distributed measurements of long-length fiber Bragg gratings (FBGs) based on optical frequency domain reflectometry (OFDR). Bragg wavelength shifts in interfered signals of OFDR are regarded as group delay. By calculating group delay, the distribution of Bragg wavelength shifts is obtained with high computational efficiency. We introduce weighted averaging process for noise reduction. This method required only 3.5% of signal processing time which was necessary for conventional equivalent signal processing based on short-time Fourier transform. The method also showed high sensitivity to experimental signals where non-uniform strain distributions existed in a long-length FBG.

  12. Frequency Domain Training-Aided Channel Estimation and Equalization in Time-Varying Optical Transmission Systems

    DEFF Research Database (Denmark)

    Pittalà, Fabio; Msallem, Majdi; Hauske, Fabian N.;

    2012-01-01

    We propose a non-weighted feed-forward equalization method with filter update by averaging channel estimations based on short CAZAC sequences. Three averaging methods are presented and tested by simulations in a time-varying 2×2 MIMO optical system....

  13. Accurate reconstruction of the optical parameter distribution in participating medium based on the frequency-domain radiative transfer equation

    Science.gov (United States)

    Qiao, Yao-Bin; Qi, Hong; Zhao, Fang-Zhou; Ruan, Li-Ming

    2016-12-01

    Reconstructing the distribution of optical parameters in the participating medium based on the frequency-domain radiative transfer equation (FD-RTE) to probe the internal structure of the medium is investigated in the present work. The forward model of FD-RTE is solved via the finite volume method (FVM). The regularization term formatted by the generalized Gaussian Markov random field model is used in the objective function to overcome the ill-posed nature of the inverse problem. The multi-start conjugate gradient (MCG) method is employed to search the minimum of the objective function and increase the efficiency of convergence. A modified adjoint differentiation technique using the collimated radiative intensity is developed to calculate the gradient of the objective function with respect to the optical parameters. All simulation results show that the proposed reconstruction algorithm based on FD-RTE can obtain the accurate distributions of absorption and scattering coefficients. The reconstructed images of the scattering coefficient have less errors than those of the absorption coefficient, which indicates the former are more suitable to probing the inner structure. Project supported by the National Natural Science Foundation of China (Grant No. 51476043), the Major National Scientific Instruments and Equipment Development Special Foundation of China (Grant No. 51327803), and the Foundation for Innovative Research Groups of the National Natural Science Foundation of China (Grant No. 51121004).

  14. A decade-spanning high-resolution asynchronous optical sampling terahertz time-domain and frequency comb spectrometer

    Science.gov (United States)

    Good, Jacob T.; Holland, Daniel B.; Finneran, Ian A.; Carroll, P. Brandon; Kelley, Matthew J.; Blake, Geoffrey A.

    2015-10-01

    We present the design and capabilities of a high-resolution, decade-spanning ASynchronous OPtical Sampling (ASOPS)-based TeraHertz Time-Domain Spectroscopy (THz-TDS) instrument. Our system employs dual mode-locked femtosecond Ti:Sapphire oscillators with repetition rates offset locked at 100 Hz via a Phase-Locked Loop (PLL) operating at the 60th harmonic of the ˜80 MHz oscillator repetition rates. The respective time delays of the individual laser pulses are scanned across a 12.5 ns window in a laboratory scan time of 10 ms, supporting a time delay resolution as fine as 15.6 fs. The repetition rate of the pump oscillator is synchronized to a Rb frequency standard via a PLL operating at the 12th harmonic of the oscillator repetition rate, achieving milliHertz (mHz) stability. We characterize the timing jitter of the system using an air-spaced etalon, an optical cross correlator, and the phase noise spectrum of the PLL. Spectroscopic applications of ASOPS-THz-TDS are demonstrated by measuring water vapor absorption lines from 0.55 to 3.35 THz and acetonitrile absorption lines from 0.13 to 1.39 THz in a short pathlength gas cell. With 70 min of data acquisition, a 50 dB signal-to-noise ratio is achieved. The achieved root-mean-square deviation is 14.6 MHz, with a mean deviation of 11.6 MHz, for the measured water line center frequencies as compared to the JPL molecular spectroscopy database. Further, with the same instrument and data acquisition hardware, we use the ability to control the repetition rate of the pump oscillator to enable THz frequency comb spectroscopy (THz-FCS). Here, a frequency comb with a tooth width of 5 MHz is generated and used to fully resolve the pure rotational spectrum of acetonitrile with Doppler-limited precision. The oscillator repetition rate stability achieved by our PLL lock circuits enables sub-MHz tooth width generation, if desired. This instrument provides unprecedented decade-spanning, tunable resolution, from 80 MHz down to sub

  15. Generalized regression neural network trained preprocessing of frequency domain correlation filter for improved face recognition and its optical implementation

    Science.gov (United States)

    Banerjee, Pradipta K.; Datta, Asit K.

    2013-02-01

    The paper proposes an improved strategy for face recognition using correlation filter under varying lighting conditions and occlusion where spatial domain preprocessing is carried out by two convolution kernels. The first convolution kernel is a contour kernel for emphasizing high frequency components of face image and the other kernel is a smoothing kernel used for minimization of noise those may arise due to preprocessing. The convolution kernels are obtained by training a generalized regression neural network using enhanced face features. Face features are enhanced by conventional principal component analysis. The proposed method reduces the false acceptance rate and false rejection rate in comparison to other standard correlation filtering techniques. Moreover, the processing is fast when compared to the existing illumination normalization techniques. A scheme of hardware implementation of all optical correlation technique is also suggested based on single spatial light modulator in a beam folding architecture. Two benchmark databases YaleB and PIE are used for performance verification of the proposed scheme and the improved results are obtained for both illumination variations and occlusions in test face images.

  16. Method and Apparatus of Multiplexing and Acquiring Data from Multiple Optical Fibers Using a Single Data Channel of an Optical Frequency-Domain Reflectometry (OFDR) System

    Science.gov (United States)

    Parker, Jr., Allen R (Inventor); Chan, Hon Man (Inventor); Piazza, Anthony (Nino) (Inventor); Richards, William Lance (Inventor)

    2014-01-01

    A method and system for multiplexing a network of parallel fiber Bragg grating (FBG) sensor-fibers to a single acquisition channel of a closed Michelson interferometer system via a fiber splitter by distinguishing each branch of fiber sensors in the spatial domain. On each branch of the splitter, the fibers have a specific pre-determined length, effectively separating each branch of fiber sensors spatially. In the spatial domain the fiber branches are seen as part of one acquisition channel on the interrogation system. However, the FBG-reference arm beat frequency information for each fiber is retained. Since the beat frequency is generated between the reference arm, the effective fiber length of each successive branch includes the entire length of the preceding branch. The multiple branches are seen as one fiber having three segments where the segments can be resolved. This greatly simplifies optical, electronic and computational complexity, and is especially suited for use in multiplexed or branched OFS networks for SHM of large and/or distributed structures which need a lot of measurement points.

  17. Optical time-domain mixer

    Science.gov (United States)

    Valley, George C.; Sefler, George A.

    2010-08-01

    We simulate an optical time-domain mixer that can be used to make a photonic analog-to-digital converter (ADC) or a digital demodulator for high-speed optical communications signals. In the basic mixer, a high frequency RF signal modulates a repetitively chirped optical carrier; this RF/optical waveform then is dispersed in one transverse dimension, and imaged onto a 2-dimensional transparency or spatial light modulator whose pixels are modulated with randomly chosen transmission or reflection coefficients (the optical mixing matrix). Following transmission through or reflection from the mixing matrix, the optical waveform from each row of the matrix is recombined and directed to a photodiode and electronics that integrate over the repetition period of the chirped source. Finally, each of these signals is digitized by an independent ADC sampling at a rate equal to the pulse repetition rate of the chirp source. A digital replica of the input RF signal can be recovered by digital signal processing from the digital output of the ADCs and the values of the transmission or reflection coefficients of the mixing matrix. The effective sampling rate is given by the number of pixels per row of the mixing matrix times the repetition rate of the chirp source while the effective resolution is controlled by the resolution of the electronic ADCs and the distortions introduced by the optical mixing process.

  18. Bio-Photonic Detection and Quantitative Evaluation Method for the Progression of Dental Caries Using Optical Frequency-Domain Imaging Method

    Science.gov (United States)

    Wijesinghe, Ruchire Eranga; Cho, Nam Hyun; Park, Kibeom; Jeon, Mansik; Kim, Jeehyun

    2016-01-01

    The initial detection of dental caries is an essential biomedical requirement to barricade the progression of caries and tooth demineralization. The objective of this study is to introduce an optical frequency-domain imaging technique based quantitative evaluation method to calculate the volume and thickness of enamel residual, and a quantification method was developed to evaluate the total intensity fluctuation in depth direction owing to carious lesions, which can be favorable to identify the progression of dental caries in advance. The cross-sectional images of the ex vivo tooth samples were acquired using 1.3 μm spectral domain optical coherence tomography system (SD-OCT). Moreover, the advantages of the proposed method over the conventional dental inspection methods were compared to highlight the potential capability of OCT. As a consequence, the threshold parameters obtained through the developed method can be used as an efficient investigating technique for the initial detection of demineralization. PMID:27929440

  19. Frequency domain processing of on-chip biphoton frequency comb

    CERN Document Server

    Jaramillo-Villegas, Jose A; Odele, Ogaga D; Leaird, Daniel E; Ou, Zhe-Yu; Qi, Minghao; Weiner, Andrew M

    2016-01-01

    Quantum information processing (QIP) promises to improve the security of our communications as well as to solve some algorithms with exponential complexity in polynomial time. Biphotons have been demonstrated as one of the most promising platforms for real implementations of QIP systems. In particular, time-bin entangled photons have been used for implementations of quantum gates which require highly stable interferometers. On the other hand, frequency-bin entanglement has been proposed to avoid the use of interferometers and the complexity of their stabilization, which potentially makes the implementation of quantum gates highly scalable. Through Fourier transform pulse shaping and electro-optic modulation, there has been a wide range of experiments that show control of entangled photons in the frequency domain. In addition, biphoton frequency combs (BFC) have also been generated using bulk optics and frequency filtering of broadband continuous biphoton spectra. However, on-chip entangled photon pair generat...

  20. Universal Optical Frequency Comb

    CERN Document Server

    Savchenkov, A A; Liang, W; Ilchenko, V S; Seidel, D; Maleki, L

    2010-01-01

    We demonstrate that whispering gallery mode resonators can be utilized to generate optical frequency combs based on four wave mixing process at virtually any frequency that lies in the transparency window of the resonator host material. We show theoretically how the morphology of the resonator can be engineered to produce a family of spectrally equidistant modes with anomalous group velocity dispersion appropriate for the comb generation. We present experimental results for a frequency comb centered at 794 nm to support our theoretical findings.

  1. Experimental demonstration of half cycle 64-QAM Nyquist-SCM direct-detection optical communication system with data-aided estimation and overlap frequency-domain equalization

    Science.gov (United States)

    Li, Danyu; He, Jing; Tang, Jin; Chen, Ming; Chen, Lin

    2014-12-01

    A half cycle 64-quadrature amplitude modulation (QAM) Nyquist subcarrier modulation (SCM) polarization division multiplexing (PDM) intensity modulation direct detection optical communication system is experimentally demonstrated. At the receiver, training sequences-based channel estimation and an overlap frequency domain equalization method are proposed to enhance the system performance. The experimental results show that the half cycle 64-QAM Nyquist-SCM PDM signal can be transmitted over 43-km standard single-mode fibers with a bit error rate below the forward error coding threshold of 2.4×10-2.

  2. The determination of the thickness and the optical dispersion property of gold film using spectroscopy of a surface plasmon in the frequency domain

    Institute of Scientific and Technical Information of China (English)

    Huang Yan; Ye Hong-An; Li Song-Quan; Dou Yin-Feng

    2013-01-01

    We propose to use wavelength modulation approach,i.e.,the spectroscopy of a surface plasmon in the frequency domain,to characterize the optical dispersion property of gold film.Using this method,we determine the dispersion relationship of gold film in a wavelength range from 537.12 nm to 905.52 nm,and our results accord well with the reported results by other authors.This method is particularly suited for studying the optical dispersion properties of thin metal films,because a series of dielectric constants over a wide spectral range can be determined simultaneously via only a single scan of the incident angle,thereby avoiding the repeated measurements required when using the angular modulation approach.

  3. Signal to Noise Ratio (SNR Enhancement Comparison of Impulse-, Coding- and Novel Linear-Frequency-Chirp-Based Optical Time Domain Reflectometry (OTDR for Passive Optical Network (PON Monitoring Based on Unique Combinations of Wavelength Selective Mirrors

    Directory of Open Access Journals (Sweden)

    Christopher M. Bentz

    2014-03-01

    Full Text Available We compare optical time domain reflectometry (OTDR techniques based on conventional single impulse, coding and linear frequency chirps concerning their signal to noise ratio (SNR enhancements by measurements in a passive optical network (PON with a maximum one-way attenuation of 36.6 dB. A total of six subscribers, each represented by a unique mirror pair with narrow reflection bandwidths, are installed within a distance of 14 m. The spatial resolution of the OTDR set-up is 3.0 m.

  4. Comparison of the domain and frequency domain state feedbacks

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, S.Y.

    1986-01-01

    In this paper, we present explicitly the equivalence of the time domain and frequency domain state feedbacks, as well as the dynamic state feedback and a modified frequency domain state feedback, from the closed-loop transfer function point of view. The difference of the two approaches is also shown.

  5. Spatial frequency domain error budget

    Energy Technology Data Exchange (ETDEWEB)

    Hauschildt, H; Krulewich, D

    1998-08-27

    The aim of this paper is to describe a methodology for designing and characterizing machines used to manufacture or inspect parts with spatial-frequency-based specifications. At Lawrence Livermore National Laboratory, one of our responsibilities is to design or select the appropriate machine tools to produce advanced optical and weapons systems. Recently, many of the component tolerances for these systems have been specified in terms of the spatial frequency content of residual errors on the surface. We typically use an error budget as a sensitivity analysis tool to ensure that the parts manufactured by a machine will meet the specified component tolerances. Error budgets provide the formalism whereby we account for all sources of uncertainty in a process, and sum them to arrive at a net prediction of how "precisely" a manufactured component can meet a target specification. Using the error budget, we are able to minimize risk during initial stages by ensuring that the machine will produce components that meet specifications before the machine is actually built or purchased. However, the current error budgeting procedure provides no formal mechanism for designing machines that can produce parts with spatial-frequency-based specifications. The output from the current error budgeting procedure is a single number estimating the net worst case or RMS error on the work piece. This procedure has limited ability to differentiate between low spatial frequency form errors versus high frequency surface finish errors. Therefore the current error budgeting procedure can lead us to reject a machine that is adequate or accept a machine that is inadequate. This paper will describe a new error budgeting methodology to aid in the design and characterization of machines used to manufacture or inspect parts with spatial-frequency-based specifications. The output from this new procedure is the continuous spatial frequency content of errors that result on a machined part. If the machine

  6. Robust and fast characterization of OCT-based optical attenuation using a novel frequency-domain algorithm for brain cancer detection

    Science.gov (United States)

    Yuan, Wu; Kut, Carmen; Liang, Wenxuan; Li, Xingde

    2017-03-01

    Cancer is known to alter the local optical properties of tissues. The detection of OCT-based optical attenuation provides a quantitative method to efficiently differentiate cancer from non-cancer tissues. In particular, the intraoperative use of quantitative OCT is able to provide a direct visual guidance in real time for accurate identification of cancer tissues, especially these without any obvious structural layers, such as brain cancer. However, current methods are suboptimal in providing high-speed and accurate OCT attenuation mapping for intraoperative brain cancer detection. In this paper, we report a novel frequency-domain (FD) algorithm to enable robust and fast characterization of optical attenuation as derived from OCT intensity images. The performance of this FD algorithm was compared with traditional fitting methods by analyzing datasets containing images from freshly resected human brain cancer and from a silica phantom acquired by a 1310 nm swept-source OCT (SS-OCT) system. With graphics processing unit (GPU)-based CUDA C/C++ implementation, this new attenuation mapping algorithm can offer robust and accurate quantitative interpretation of OCT images in real time during brain surgery.

  7. Robust and fast characterization of OCT-based optical attenuation using a novel frequency-domain algorithm for brain cancer detection

    Science.gov (United States)

    Yuan, Wu; Kut, Carmen; Liang, Wenxuan; Li, Xingde

    2017-01-01

    Cancer is known to alter the local optical properties of tissues. The detection of OCT-based optical attenuation provides a quantitative method to efficiently differentiate cancer from non-cancer tissues. In particular, the intraoperative use of quantitative OCT is able to provide a direct visual guidance in real time for accurate identification of cancer tissues, especially these without any obvious structural layers, such as brain cancer. However, current methods are suboptimal in providing high-speed and accurate OCT attenuation mapping for intraoperative brain cancer detection. In this paper, we report a novel frequency-domain (FD) algorithm to enable robust and fast characterization of optical attenuation as derived from OCT intensity images. The performance of this FD algorithm was compared with traditional fitting methods by analyzing datasets containing images from freshly resected human brain cancer and from a silica phantom acquired by a 1310 nm swept-source OCT (SS-OCT) system. With graphics processing unit (GPU)-based CUDA C/C++ implementation, this new attenuation mapping algorithm can offer robust and accurate quantitative interpretation of OCT images in real time during brain surgery. PMID:28327613

  8. OTDM-to-WDM Conversion Based on Time-to-Frequency Mapping by Time-Domain Optical Fourier Transformation

    DEFF Research Database (Denmark)

    Palushani, Evarist; Mulvad, Hans Christian Hansen; Galili, Michael

    2012-01-01

    a dispersive medium followed by phase modulation; the latter being achieved by a four-wave mixing process with linearly chirped pump pulses. Both numerical and experimental investigations of the OTDM-to-WDM conversion technique are carried out. Experimental validations are performed on......This paper reports on the utilization of the timedomain optical Fourier transformation (OFT) technique for serial-to-parallel conversion of optical time division multiplexed (OTDM) data tributaries into dense wavelength division multiplexed (DWDM) channels. The OFT is implemented by using...

  9. Frequency domain FIR and IIR adaptive filters

    Science.gov (United States)

    Lynn, D. W.

    1990-01-01

    A discussion of the LMS adaptive filter relating to its convergence characteristics and the problems associated with disparate eigenvalues is presented. This is used to introduce the concept of proportional convergence. An approach is used to analyze the convergence characteristics of block frequency-domain adaptive filters. This leads to a development showing how the frequency-domain FIR adaptive filter is easily modified to provide proportional convergence. These ideas are extended to a block frequency-domain IIR adaptive filter and the idea of proportional convergence is applied. Experimental results illustrating proportional convergence in both FIR and IIR frequency-domain block adaptive filters is presented.

  10. Anti-aliasing Wiener filtering for wave-front reconstruction in the spatial-frequency domain for high-order astronomical adaptive-optics systems.

    Science.gov (United States)

    Correia, Carlos M; Teixeira, Joel

    2014-12-01

    Computationally efficient wave-front reconstruction techniques for astronomical adaptive-optics (AO) systems have seen great development in the past decade. Algorithms developed in the spatial-frequency (Fourier) domain have gathered much attention, especially for high-contrast imaging systems. In this paper we present the Wiener filter (resulting in the maximization of the Strehl ratio) and further develop formulae for the anti-aliasing (AA) Wiener filter that optimally takes into account high-order wave-front terms folded in-band during the sensing (i.e., discrete sampling) process. We employ a continuous spatial-frequency representation for the forward measurement operators and derive the Wiener filter when aliasing is explicitly taken into account. We further investigate and compare to classical estimates using least-squares filters the reconstructed wave-front, measurement noise, and aliasing propagation coefficients as a function of the system order. Regarding high-contrast systems, we provide achievable performance results as a function of an ensemble of forward models for the Shack-Hartmann wave-front sensor (using sparse and nonsparse representations) and compute point-spread-function raw intensities. We find that for a 32×32 single-conjugated AOs system the aliasing propagation coefficient is roughly 60% of the least-squares filters, whereas the noise propagation is around 80%. Contrast improvements of factors of up to 2 are achievable across the field in the H band. For current and next-generation high-contrast imagers, despite better aliasing mitigation, AA Wiener filtering cannot be used as a standalone method and must therefore be used in combination with optical spatial filters deployed before image formation actually takes place.

  11. Optical frequency combs generated mechanically

    CERN Document Server

    Sumetsky, M

    2016-01-01

    It is shown that a highly equidistant optical frequency comb can be generated by the parametric excitation of an optical bottle microresonator with nanoscale effective radius variation by its natural mechanical vibrations.

  12. Frequency Domain Image Filtering Using CUDA

    Directory of Open Access Journals (Sweden)

    Muhammad Awais Rajput

    2014-10-01

    Full Text Available In this paper, we investigate the implementation of image filtering in frequency domain using NVIDIA?s CUDA (Compute Unified Device Architecture. In contrast to signal and image filtering in spatial domain which uses convolution operations and hence is more compute-intensive for filters having larger spatial extent, the frequency domain filtering uses FFT (Fast Fourier Transform which is much faster and significantly reduces the computational complexity of the filtering. We implement the frequency domain filtering on CPU and GPU respectively and analyze the speed-up obtained from the CUDA?s parallel processing paradigm. In order to demonstrate the efficiency of frequency domain filtering on CUDA, we implement three frequency domain filters, i.e., Butterworth, low-pass and Gaussian for processing different sizes of images on CPU and GPU respectively and perform the GPU vs. CPU benchmarks. The results presented in this paper show that the frequency domain filtering with CUDA achieves significant speed-up over the CPU processing in frequency domain with the same level of (output image quality on both the processing architectures

  13. Arbitrary optical frequency synthesis traced to an optical frequency comb

    Science.gov (United States)

    Cai, Zihang; Zhang, Weipeng; Yang, Honglei; Li, Yan; Wei, Haoyun

    2016-11-01

    An arbitrary optical frequency synthesizer with a broad tuning range and high frequency accuracy is presented. The system includes an external cavity diode laser (ECDL) as the output laser, an Erbium-doped optical frequency comb being a frequency reference, and a control module. The optical frequency from the synthesizer can be continuously tuned by the large-scale trans-tooth switch and the fine intra-tooth adjustment. Robust feedback control by regulating the current and PZT voltage enables the ECDL to phase-lock to the Erbium-doped optical frequency comb, therefore to keep stable frequency output. In the meanwhile, the absolute frequency of the synthesizer is determined by the repetition rate, the offset frequency and the beat frequency. All the phase lock loops in the system are traced back to a Rubidium clock. A powerful and friendly software is developed to make the operation convenient by integrating the functions of frequency setting, tuning, tracing, locking and measuring into a LabVIEW interface. The output frequency tuning span and the uncertainty of the system are evaluated as >6 THz and Ring-Down Spectroscopy.

  14. System Identification A Frequency Domain Approach

    CERN Document Server

    Pintelon, Rik

    2012-01-01

    System identification is a general term used to describe mathematical tools and algorithms that build dynamical models from measured data. Used for prediction, control, physical interpretation, and the designing of any electrical systems, they are vital in the fields of electrical, mechanical, civil, and chemical engineering. Focusing mainly on frequency domain techniques, System Identification: A Frequency Domain Approach, Second Edition also studies in detail the similarities and differences with the classical time domain approach. It high??lights many of the important steps in the identi

  15. Active Faraday optical frequency standard.

    Science.gov (United States)

    Zhuang, Wei; Chen, Jingbiao

    2014-11-01

    We propose the mechanism of an active Faraday optical clock, and experimentally demonstrate an active Faraday optical frequency standard based on narrow bandwidth Faraday atomic filter by the method of velocity-selective optical pumping of cesium vapor. The center frequency of the active Faraday optical frequency standard is determined by the cesium 6 (2)S(1/2) F=4 to 6 (2)P(3/2) F'=4 and 5 crossover transition line. The optical heterodyne beat between two similar independent setups shows that the frequency linewidth reaches 281(23) Hz, which is 1.9×10(4) times smaller than the natural linewidth of the cesium 852-nm transition line. The maximum emitted light power reaches 75 μW. The active Faraday optical frequency standard reported here has advantages of narrow linewidth and reduced cavity pulling, which can readily be extended to other atomic transition lines of alkali and alkaline-earth metal atoms trapped in optical lattices at magic wavelengths, making it useful for new generation of optical atomic clocks.

  16. Microresonator Frequency Comb Optical Clock

    Science.gov (United States)

    2014-07-22

    Number Microresonator frequency comb optical clock Block 13: Supplementary Note © 2014 . Published in Optica , Vol. Ed. 0 1, (1) (2014), (, (1). DoD...Oscillators. http://dx.doi.org/10.1364/ OPTICA .1.000010 1. INTRODUCTION Optical frequency combs enable extraordinary measurement precision and accuracy...1, No. 1 / July 2014 / Optica 10 deviation for 1 s averaging is completely dominated by the Rb reference, and the microcomb contribution is only ɚ

  17. Real-time spatial frequency domain imaging by single snapshot multiple frequency demodulation technique

    Science.gov (United States)

    Cao, Zili; Lin, Weihao; Chen, Xinlin; Zeng, Bixin; Xu, Min

    2017-02-01

    We have presented a novel Single Snapshot Multiple Frequency Demodulation (SSMD) method enabling single snapshot wide field imaging of optical properties of turbid media in the Spatial Frequency Domain. SSMD makes use of the orthogonality of harmonic functions and extracts the modulation transfer function (MTF) at multiple modulation frequencies and of arbitrary orientations and amplitudes simultaneously from a single structured-illuminated image at once. SSMD not only increases significantly the data acquisition speed and reduces motion artifacts but also exhibits excellent noise suppression in imaging as well. The performance of SSMD-SFDI is demonstrated with experiments on both tissue mimicking phantoms and in vivo for recovering optical properties. SSMD is ideal in the implementation of a real-time spatial frequency domain imaging platform, which will open up SFDI for vast applications in, for example, mapping the optical properties of a dynamic turbid medium or monitoring fast temporal evolutions.

  18. Spatial frequency domain spectroscopy of two layer media

    Science.gov (United States)

    Yudovsky, Dmitry; Durkin, Anthony J.

    2011-10-01

    Monitoring of tissue blood volume and oxygen saturation using biomedical optics techniques has the potential to inform the assessment of tissue health, healing, and dysfunction. These quantities are typically estimated from the contribution of oxyhemoglobin and deoxyhemoglobin to the absorption spectrum of the dermis. However, estimation of blood related absorption in superficial tissue such as the skin can be confounded by the strong absorption of melanin in the epidermis. Furthermore, epidermal thickness and pigmentation varies with anatomic location, race, gender, and degree of disease progression. This study describes a technique for decoupling the effect of melanin absorption in the epidermis from blood absorption in the dermis for a large range of skin types and thicknesses. An artificial neural network was used to map input optical properties to spatial frequency domain diffuse reflectance of two layer media. Then, iterative fitting was used to determine the optical properties from simulated spatial frequency domain diffuse reflectance. Additionally, an artificial neural network was trained to directly map spatial frequency domain reflectance to sets of optical properties of a two layer medium, thus bypassing the need for iteration. In both cases, the optical thickness of the epidermis and absorption and reduced scattering coefficients of the dermis were determined independently. The accuracy and efficiency of the iterative fitting approach was compared with the direct neural network inversion.

  19. Domain Decomposition Solvers for Frequency-Domain Finite Element Equations

    KAUST Repository

    Copeland, Dylan

    2010-10-05

    The paper is devoted to fast iterative solvers for frequency-domain finite element equations approximating linear and nonlinear parabolic initial boundary value problems with time-harmonic excitations. Switching from the time domain to the frequency domain allows us to replace the expensive time-integration procedure by the solution of a simple linear elliptic system for the amplitudes belonging to the sine- and to the cosine-excitation or a large nonlinear elliptic system for the Fourier coefficients in the linear and nonlinear case, respectively. The fast solution of the corresponding linear and nonlinear system of finite element equations is crucial for the competitiveness of this method. © 2011 Springer-Verlag Berlin Heidelberg.

  20. Load Estimation by Frequency Domain Decomposition

    DEFF Research Database (Denmark)

    Pedersen, Ivar Chr. Bjerg; Hansen, Søren Mosegaard; Brincker, Rune;

    2007-01-01

    When performing operational modal analysis the dynamic loading is unknown, however, once the modal properties of the structure have been estimated, the transfer matrix can be obtained, and the loading can be estimated by inverse filtering. In this paper loads in frequency domain are estimated...... by analysis of simulated responses of a 4 DOF system, for which the exact modal parameters are known. This estimation approach entails modal identification of the natural eigenfrequencies, mode shapes and damping ratios by the frequency domain decomposition technique. Scaled mode shapes are determined by use...

  1. Realization of Thermal Inertia in Frequency Domain

    Directory of Open Access Journals (Sweden)

    Boe-Shong Hong

    2014-02-01

    Full Text Available To realize the lagging behavior in heat conduction observed in these two decades, this paper firstly theoretically excludes the possibility that the underlying thermal inertia is a result of the time delay in heat diffusion. Instead, we verify in experiments the electro-thermal analogy, wherein the thermal inertial is parameterized by thermal inductance that formulates hyperbolic heat-conduction. The thermal hyperbolicity exhibits a special frequency response in Bode plot, wherein the amplitude ratios is kept flat after crossing some certain frequency, as opposed to Fourier heat-conduction. We apply this specialty to design an instrument that reliably identifies thermal inductances of some materials in frequency domain. The instrument is embedded with a DSP-based frequency synthesizer capable of modulating frequencies in utmost high-resolution. Thermal inertia implies a new possibility for energy storage in analogy to inductive energy storage in electricity or mechanics.

  2. Optical Fibre Based Frequency Shifters Project

    Science.gov (United States)

    1991-01-28

    A fibre optic frequency shifter can be used to replace the Bragg cell acousto-optic modulator, currently used to generate low frequency optical...carriers, in fibre optic communications and sensor systems. This new form of frequency shifter, being an all fibre device, in which the propagating optical...large number of workers in recent years, (for example references [2-81 and those contained therein). The main elements of a fibre - optic frequency

  3. Microcirculation monitoring with real time spatial frequency domain imaging

    Science.gov (United States)

    Chen, Xinlin; Cao, Zili; Lin, Weihao; Zhu, Danfeng; Zhu, Xiuwei; Zeng, Bixin; Xu, M.

    2017-01-01

    We present a spatial frequency domain imaging (SFDI) study of local hemodynamics in the forearm of healthy volunteers performing paced breathing. Real time Single Snapshot Multiple Frequency Demodulation - Spatial Frequency Domain Imaging (SSMD-SFDI) was used to map the optical properties of the subsurface of the forearm continuously. The oscillations of the concentrations of deoxy- and oxyhemoglobin at the subsurface of the forearm induced by paced breathing are found to be close to out-of-phase, attributed to the dominance of the blood flow modulation by paced breathing. The properties of local microcirculation including the blood transit times through capillaries and venules are extracted by fitting to Simplified Hemodynamics Model. Our preliminary results suggest that the real time SSMD-SFDI platform may serve as one effective imaging modality for microcirculation monitoring.

  4. Photon counts modulation in optical time domain reflectometry

    Institute of Scientific and Technical Information of China (English)

    Wang Xiao-Bo; Wang Jing-Jing; Zhang Guo-Feng; Xiao Lian-Tuan; Jia Suo-Tang

    2011-01-01

    The quantum fluctuation of photon counting limits the field application of optical time domain reflection. A method of photon counts modulation optics time domain reflection with single photon detection at 1.55 un is presented. The influence of quantum fluctuation can be effectively controlled by demodulation technology since quantum fluctuation shows a uniform distribution in the frequency domain. Combined with the changing of the integration time of the lock-in amplifier, the signal to noise ratio is significantly enhanced. Accordingly the signal to noise improvement ratio reaches 31.7 dB compared with the direct photon counting measurement.

  5. Correlation between skin, bone, and cerebrospinal fluid layer thickness and optical coefficients measured by multidistance frequency-domain near-infrared spectroscopy in term and preterm infants

    Science.gov (United States)

    Demel, Anja; Feilke, Katharina; Wolf, Martin; Poets, Christian F.; Franz, Axel R.

    2014-01-01

    Near-infrared spectroscopy (NIRS) is increasingly used in neonatal intensive care. We investigated the impact of skin, bone, and cerebrospinal fluid (CSF) layer thickness in term and preterm infants on absorption-(μa) and/or reduced scattering coefficients (μs‧) measured by multidistance frequency-domain (FD)-NIRS. Transcranial ultrasound was performed to measure the layer thicknesses. Correlations were only statistically significant for μa at 692 nm with bone thickness and μs‧ at 834 nm with skin thickness. There is no evidence that skin, bone, or CSF thickness have an important effect on μa and μs‧. Layer thicknesses of skin, bone, and CSF in the range studied do not seem to affect cerebral oxygenation measurements by multidistance FD-NIRS significantly.

  6. Spatial frequency domain imaging for monitoring palpable breast lesions

    Science.gov (United States)

    Robbins, Constance M.; Antaki, James F.; Kainerstorfer, Jana M.

    2017-02-01

    We describe a novel approach for monitoring breast lesions, utilizing spatial frequency domain imaging, a diffuse optical imaging method to detect hemoglobin contrast, in combination with mechanical compression of the tissue. The project is motivated by the growing rate of unnecessary breast biopsies, caused by uncertainty in X-ray mammographic diagnoses. We believe there is a need for an alternate means of tracking the progression palpable lesions exhibiting probably benign features, that can be performed non-invasively and hence frequently: at home or in the clinic. The proposed approach capitalizes on two distinguishing properties of cancerous lesions, namely the relative stiffness with respect to surrounding tissue and the optical absorption due to the greater vascularization, hence hemoglobin concentration. The current research project is a pilot study to evaluate the principle on soft, breast tissue-mimicking phantoms containing stiffer, more highly absorbing inclusions. Spatial frequency domain imaging was performed by projecting onto the phantom a series of wide-field patterns at multiple spatial frequencies. Image analysis then was performed to map absorption and scattering properties. The results of the study demonstrate that compression significantly increases the optical contrast observed for inclusions located 10 and 15 mm beneath the surface. In the latter case, the inclusion was not detectable without compression.

  7. All-optical orthogonal frequency division multiplexing (OFDM) transmitter

    DEFF Research Database (Denmark)

    2015-01-01

    The invention relates to an all-optical orthogonal frequency division multiplexing (OFDM) transmitter for generating an OFDM output signal. The transmitter comprises a first time-domain optical Fourier transform (OFT) assembly, the first OFT assembly is of a K-D-K configuration and comprises...

  8. Different ways to active optical frequency standards

    Science.gov (United States)

    Pan, Duo; Xue, Xiaobo; Zhang, Xiaogang; Chen, Jingbiao

    2016-06-01

    Active optical frequency standard, or active optical clock, is a new concept of optical frequency standard, where a weak feedback with phase coherence information in optical bad-cavity limitation is formed, and the continuous self-sustained coherent stimulated emission between two atomic transition levels with population inversion is realized. Through ten years of both theoretical and experimental exploration, the narrow linewidth and suppression of cavity pulling effect of active optical frequency standard have been initially proved. In this paper, after a simple review, we will mainly present the most recent experimental progresses of active optical frequency standards in Peking University, including 4-level cesium active optical frequency standards and active Faraday optical frequency standards. The future development of active optical frequency standards is also discussed.

  9. Time delay measurement in the frequency domain

    Energy Technology Data Exchange (ETDEWEB)

    Durbin, Stephen M., E-mail: durbin@purdue.edu; Liu, Shih-Chieh [Purdue University, West Lafayette, IN 47907 (United States); Dufresne, Eric M.; Li, Yuelin; Wen, Haidan [Argonne National Laboratory, Argonne, IL 60439 (United States)

    2015-08-06

    A simple frequency domain technique for determining the time delay between laser pump and X-ray probe pulses achieves 1 ps resolution even for ∼100 ps synchrotron pulses, permitting improved pump–probe characterization of ultrafast processes. Pump–probe studies at synchrotrons using X-ray and laser pulses require accurate determination of the time delay between pulses. This becomes especially important when observing ultrafast responses with lifetimes approaching or even less than the X-ray pulse duration (∼100 ps). The standard approach of inspecting the time response of a detector sensitive to both types of pulses can have limitations due to dissimilar pulse profiles and other experimental factors. Here, a simple alternative is presented, where the frequency response of the detector is monitored versus time delay. Measurements readily demonstrate a time resolution of ∼1 ps. Improved precision is possible by simply extending the data acquisition time.

  10. Communicating oscillatory networks: frequency domain analysis

    Directory of Open Access Journals (Sweden)

    Ihekwaba Adaoha EC

    2011-12-01

    Full Text Available Abstract Background Constructing predictive dynamic models of interacting signalling networks remains one of the great challenges facing systems biology. While detailed dynamical data exists about individual pathways, the task of combining such data without further lengthy experimentation is highly nontrivial. The communicating links between pathways, implicitly assumed to be unimportant and thus excluded, are precisely what become important in the larger system and must be reinstated. To maintain the delicate phase relationships between signals, signalling networks demand accurate dynamical parameters, but parameters optimised in isolation and under varying conditions are unlikely to remain optimal when combined. The computational burden of estimating parameters increases exponentially with increasing system size, so it is crucial to find precise and efficient ways of measuring the behaviour of systems, in order to re-use existing work. Results Motivated by the above, we present a new frequency domain-based systematic analysis technique that attempts to address the challenge of network assembly by defining a rigorous means to quantify the behaviour of stochastic systems. As our focus we construct a novel coupled oscillatory model of p53, NF-kB and the mammalian cell cycle, based on recent experimentally verified mathematical models. Informed by online databases of protein networks and interactions, we distilled their key elements into simplified models containing the most significant parts. Having coupled these systems, we constructed stochastic models for use in our frequency domain analysis. We used our new technique to investigate the crosstalk between the components of our model and measure the efficacy of certain network-based heuristic measures. Conclusions We find that the interactions between the networks we study are highly complex and not intuitive: (i points of maximum perturbation do not necessarily correspond to points of maximum

  11. Dental optical coherence domain reflectometry explorer

    Energy Technology Data Exchange (ETDEWEB)

    Everett, Matthew J. (Livermore, CA); Colston, Jr., Billy W. (Livermore, CA); Sathyam, Ujwal S. (Livermore, CA); Da Silva, Luiz B. (Pleasanton, CA)

    2001-01-01

    A hand-held, fiber optic based dental device with optical coherence domain reflectometry (OCDR) sensing capabilities provides a profile of optical scattering as a function of depth in the tissue at the point where the tip of the dental explorer touches the tissue. This system provides information on the internal structure of the dental tissue, which is then used to detect caries and periodontal disease. A series of profiles of optical scattering or tissue microstructure are generated by moving the explorer across the tooth or other tissue. The profiles are combined to form a cross-sectional, or optical coherence tomography (OCT), image.

  12. Offline fusion of co-registered intravascular ultrasound and frequency domain optical coherence tomography images for the analysis of human atherosclerotic plaques

    DEFF Research Database (Denmark)

    Räber, Lorenz; Heo, Jung Ho; Radu, Maria D

    2012-01-01

    To demonstrate the feasibility and potential usefulness of an offline fusion of matched optical coherence tomography (OCT) and intravascular ultrasound (IVUS)/virtual histology (IVUS-VH) images.......To demonstrate the feasibility and potential usefulness of an offline fusion of matched optical coherence tomography (OCT) and intravascular ultrasound (IVUS)/virtual histology (IVUS-VH) images....

  13. Intra- and interobserver reliability and intra-catheter reproducibility using frequency domain optical coherence tomography for the evaluation of morphometric stent parameters and qualitative assessment of stent strut coverage

    DEFF Research Database (Denmark)

    Antonsen, Lisbeth; Thayssen, Per; Junker, Anders;

    2015-01-01

    to investigate the intra- and interobserver reliability, as well as the intra-catheter reproducibility of quantitative FD-OCT-assessment of morphometric stent parameters and qualitative FD-OCT-evaluation of strut coverage in 10 randomly selected 6-month follow-up Nobori® biolimus-eluting stents (N-BESs). METHODS...... (CI): 0.88-0.93, pquantitative evaluation of stented coronary segments, and for qualitative assessment of strut coverage.......PURPOSE: Frequency-domain optical coherence tomography (FD-OCT) is a high-resolution imaging tool (~10-15μm), which enables near-histological in-vivo images of the coronary vessel wall. The use of the technique is increasing, both for research- and clinical purposes. This study sought...

  14. On frequency and time domain models of traveling wave tubes

    CERN Document Server

    Théveny, Stéphane; Elskens, Yves

    2016-01-01

    We discuss the envelope modulation assumption of frequency-domain models of traveling wave tubes (TWTs) and test its consistency with the Maxwell equations. We compare the predictions of usual frequency-domain models with those of a new time domain model of the TWT.

  15. Millimeter wave imaging system modeling: spatial frequency domain calculation versus spatial domain calculation.

    Science.gov (United States)

    Qi, Feng; Tavakol, Vahid; Ocket, Ilja; Xu, Peng; Schreurs, Dominique; Wang, Jinkuan; Nauwelaers, Bart

    2010-01-01

    Active millimeter wave imaging systems have become a promising candidate for indoor security applications and industrial inspection. However, there is a lack of simulation tools at the system level. We introduce and evaluate two modeling approaches that are applied to active millimeter wave imaging systems. The first approach originates in Fourier optics and concerns the calculation in the spatial frequency domain. The second approach is based on wave propagation and corresponds to calculation in the spatial domain. We compare the two approaches in the case of both rough and smooth objects and point out that the spatial frequency domain calculation may suffer from a large error in amplitude of 50% in the case of rough objects. The comparison demonstrates that the concepts of point-spread function and f-number should be applied with careful consideration in coherent millimeter wave imaging systems. In the case of indoor applications, the near-field effect should be considered, and this is included in the spatial domain calculation.

  16. Optimised Design of Transparent Optical Domains

    DEFF Research Database (Denmark)

    Hanik, N.; Caspar, C.; Schmidt, F.;

    2000-01-01

    Three different design concepts for transparent, dispersion compensated, optical WDM transmission links are optimised numerically and experimentally for 10 Gbit/s data rate per channel. It is shown that robust transparent domains of 1,500 km in diameter can be realised using simple design rutes....

  17. AU-FREDI - AUTONOMOUS FREQUENCY DOMAIN IDENTIFICATION

    Science.gov (United States)

    Yam, Y.

    1994-01-01

    The Autonomous Frequency Domain Identification program, AU-FREDI, is a system of methods, algorithms and software that was developed for the identification of structural dynamic parameters and system transfer function characterization for control of large space platforms and flexible spacecraft. It was validated in the CALTECH/Jet Propulsion Laboratory's Large Spacecraft Control Laboratory. Due to the unique characteristics of this laboratory environment, and the environment-specific nature of many of the software's routines, AU-FREDI should be considered to be a collection of routines which can be modified and reassembled to suit system identification and control experiments on large flexible structures. The AU-FREDI software was originally designed to command plant excitation and handle subsequent input/output data transfer, and to conduct system identification based on the I/O data. Key features of the AU-FREDI methodology are as follows: 1. AU-FREDI has on-line digital filter design to support on-orbit optimal input design and data composition. 2. Data composition of experimental data in overlapping frequency bands overcomes finite actuator power constraints. 3. Recursive least squares sine-dwell estimation accurately handles digitized sinusoids and low frequency modes. 4. The system also includes automated estimation of model order using a product moment matrix. 5. A sample-data transfer function parametrization supports digital control design. 6. Minimum variance estimation is assured with a curve fitting algorithm with iterative reweighting. 7. Robust root solvers accurately factorize high order polynomials to determine frequency and damping estimates. 8. Output error characterization of model additive uncertainty supports robustness analysis. The research objectives associated with AU-FREDI were particularly useful in focusing the identification methodology for realistic on-orbit testing conditions. Rather than estimating the entire structure, as is

  18. Integrated 10 Gb/s multilevel multiband passive optical network and 500 Mb/s indoor visible light communication system based on Nyquist single carrier frequency domain equalization modulation.

    Science.gov (United States)

    Wang, Yuanquan; Shi, Jianyang; Yang, Chao; Wang, Yiguang; Chi, Nan

    2014-05-01

    We propose and experimentally demonstrate a novel integrated passive optical network (PON) and indoor visible light communication (VLC) system based on Nyquist single carrier frequency domain equalization (N-SC-FDE) modulation with direct detection. In this system, a directly modulated laser and a commercially available red light emitting diode are served as the transmitters of the PON and VLC, respectively. To enable high spectral efficiency, high-speed transmission, and flexible multiple access with simplified optical network unit-side digital signal processing, multilevel, multiband quadrature amplitude modulations 128/64/16 are implemented here. VLC N-SC-FDE signals are successfully delivered a further 30 cm indoor distance after transmitting over a span of 40 km single mode fiber (SMF) together with 3 sub-band PON signals. As a proof of concept, a 10 Gb/s PON and 500 Mb/s VLC integrated system for three wired users and one wireless user is successfully achieved, which shows the promising potential and feasibility of this proposal to extend multiple services from metropolitan to suburban areas.

  19. Two optical bistability domains in composites of metal nanoparticles with nonlinear dielectric core

    Energy Technology Data Exchange (ETDEWEB)

    Shewamare, Sisay, E-mail: sisayshewa20@yahoo.com [Department of Physics, Addis Ababa University, P.O. Box 1176, Addis Ababa (Ethiopia); Mal' nev, V.N., E-mail: vadimnmalnev@yahoo.com [Department of Physics, Addis Ababa University, P.O. Box 1176, Addis Ababa (Ethiopia)

    2012-12-15

    It is shown that the local field in metal spherical particles with a dielectric core in an external varying electric field has two maxima at two different frequencies. The second maximum becomes more important with an increment in the metal fraction. Due to the nonlinear dielectric function of the core, the composite of these inclusions may have two optically induced bistability domains at different frequencies. At rather high metal fraction, two bistability domains merge and form one entire bistability domain. The parameters of these domains are studied numerically. The paper focuses on the second bistability domain, which has not been discussed in the literature so far. This domain exists in a comparatively narrow frequency range and its onset fields are lower than those of the first bistability domain. The lowest bistability onset fields are obtained in the entire domain. This peculiarity of the optical induced bistability in the metal composite with small dielectric cores can be attractive for possible applications.

  20. Estimated Frequency Domain Model Uncertainties used in Robust Controller Design

    DEFF Research Database (Denmark)

    Tøffner-Clausen, S.; Andersen, Palle; Stoustrup, Jakob;

    1994-01-01

    This paper deals with the combination of system identification and robust controller design. Recent results on estimation of frequency domain model uncertainty are......This paper deals with the combination of system identification and robust controller design. Recent results on estimation of frequency domain model uncertainty are...

  1. Noise-free quantum optical frequency shifting driven by mechanics

    CERN Document Server

    Fan, Linran; Poot, Menno; Cheng, Risheng; Guo, Xiang; Han, Xu; Tang, Hong X

    2016-01-01

    The ability to manipulate single photons is of critical importance for fundamental quantum optics studies and practical implementations of quantum communications. While extraordinary progresses have been made in controlling spatial, temporal, spin and orbit angular momentum degrees of freedom, frequency-domain control of single photons so far relies on nonlinear optical effects, which have faced obstacles such as noise photons, narrow bandwidth and demanding optical filtering. Here we demonstrate the first integrated near-unity efficiency frequency manipulation of single photons, by stretching and compressing a waveguide at 8.3 billion cycles per second. Frequency shift up to 150 GHz at telecom wavelength is realized without measurable added noise and the preservation of quantum coherence is verified through quantum interference between twin photons of different colors. This single photon frequency control approach will be invaluable for increasing the channel capacity of quantum communications and compensati...

  2. Frequency Domain Electroretinography in Retinitis Pigmentosa versus Normal Eyes

    Directory of Open Access Journals (Sweden)

    Homa Hassan-Karimi

    2012-01-01

    Full Text Available Purpose: To compare electroretinogram (ERG characteristics in patients with retinitis pigmentosa (RP and normal subjects using frequency domain analysis. Methods: Five basic ERG recordings were performed in normal subjects and patients with a clinical diagnosis of RP according to the ISCEV (International Society of Clinical Electrophysiology of Vision protocol. Frequency domain analysis was performed by MATLAB software. Different frequency domain parameters were compared between the study groups. Results: Peak frequency (Fmod of flicker and oscillatory responses in RP patients showed significant (P<0.0001 high pass response as compared to normal controls. Peak frequency (Fmod of the other responses was not significantly different between the two groups. Conclusion: In addition to conventional ERG using time domain methods, frequency domain analysis may be useful for diagnosis of RP. Oscillatory and flicker responses may be analyzed in frequency domain. Fast Fourier transform may reveal two distinct high pass responses (shift to higher frequencies in Fmod. Time and frequency domain analyses may be performed simultaneously with many modern ERG machines and may therefore be recommended in RP patients.

  3. Intra- and interobserver reliability and intra-catheter reproducibility using frequency domain optical coherence tomography for the evaluation of morphometric stent parameters and qualitative assessment of stent strut coverage

    Energy Technology Data Exchange (ETDEWEB)

    Antonsen, Lisbeth, E-mail: Lisbeth.antonsen@rsyd.dk; Thayssen, Per; Junker, Anders; Veien, Karsten Tange; Hansen, Henrik Steen; Hansen, Knud Nørregaard; Hougaard, Mikkel; Jensen, Lisette Okkels

    2015-12-15

    Purpose: Frequency-domain optical coherence tomography (FD-OCT) is a high-resolution imaging tool (~ 10–15 μm), which enables near-histological in-vivo images of the coronary vessel wall. The use of the technique is increasing, both for research- and clinical purposes. This study sought to investigate the intra- and interobserver reliability, as well as the intra-catheter reproducibility of quantitative FD-OCT-assessment of morphometric stent parameters and qualitative FD-OCT-evaluation of strut coverage in 10 randomly selected 6-month follow-up Nobori® biolimus-eluting stents (N-BESs). Methods: Ten N-BESs (213 cross sectional areas (CSAs) and 1897 struts) imaged with OCT 6 months post-implantation were randomly selected and analyzed by 2 experienced analysts, and the same 10 N-BESs were analyzed by one of the analysts 3 months later. Further, 2 consecutive pullbacks randomly performed in another 10 N-BESs (219 CSAs and 1860 struts) were independently assessed by one of the analysts. Results: The intraobserver variability with regard to relative difference of mean luminal area and mean stent area at the CSA-level was very low: 0.1% ± 1.4% and 0.5% ± 3.2%. Interobserver variability also proved to be low: − 2.1% ± 3.3% and 2.1% ± 4.6%, and moreover, very restricted intra-catheter variation was observed: 0.02% ± 6.8% and − 0.18% ± 5.2%. The intraobserver-, interobserver- and intra-catheter reliability for the qualitative evaluation of strut coverage was found to be: kappa (κ) = 0.91 (95% confidence interval (CI): 0.88–0.93, p < 0.01), κ = 0.88 (95% CI: 0.85–0.91, p < 0.01), and κ = 0.73 (95% CI: 0.68–0.78, p < 0.01), respectively. Conclusions: FD-OCT is a reproducible and reliable imaging tool for quantitative evaluation of stented coronary segments, and for qualitative assessment of strut coverage. - Highlights: • Frequency-domain optical coherence tomography (FD-OCT) is increasingly adopted in the catherization laboratories. • This

  4. Fourier phase in Fourier-domain optical coherence tomography.

    Science.gov (United States)

    Uttam, Shikhar; Liu, Yang

    2015-12-01

    Phase of an electromagnetic wave propagating through a sample-of-interest is well understood in the context of quantitative phase imaging in transmission-mode microscopy. In the past decade, Fourier-domain optical coherence tomography has been used to extend quantitative phase imaging to the reflection-mode. Unlike transmission-mode electromagnetic phase, however, the origin and characteristics of reflection-mode Fourier phase are poorly understood, especially in samples with a slowly varying refractive index. In this paper, the general theory of Fourier phase from first principles is presented, and it is shown that Fourier phase is a joint estimate of subresolution offset and mean spatial frequency of the coherence-gated sample refractive index. It is also shown that both spectral-domain phase microscopy and depth-resolved spatial-domain low-coherence quantitative phase microscopy are special cases of this general theory. Analytical expressions are provided for both, and simulations are presented to explain and support the theoretical results. These results are further used to show how Fourier phase allows the estimation of an axial mean spatial frequency profile of the sample, along with depth-resolved characterization of localized optical density change and sample heterogeneity. Finally, a Fourier phase-based explanation of Doppler optical coherence tomography is also provided.

  5. Damping Estimation by Frequency Domain Decomposition

    DEFF Research Database (Denmark)

    Brincker, Rune; Ventura, C. E.; Andersen, P.

    2001-01-01

    frequencies can be accurately estimated without being limited by the frequency resolution of the discrete Fourier transform. It is explained how the spectral density matrix is decomposed into a set of single degree of freedom systems, and how the individual SDOF auto spectral density functions are transformed...

  6. Hermetic optical-fiber iodine frequency standard.

    Science.gov (United States)

    Light, Philip S; Anstie, James D; Benabid, Fetah; Luiten, Andre N

    2015-06-15

    We have built an optical-frequency standard based on interrogating iodine vapor that has been trapped within the hollow core of a hermetically sealed kagome-lattice photonic crystal fiber. A frequency-doubled Nd:YAG laser locked to a hyperfine component of the P(142)37-0 I2127 transition using modulation transfer spectroscopy shows a frequency stability of 3×10(-11) at 100 s. We discuss the impediments in integrating this all-fiber standard into a fully optical-fiber-based system, and suggest approaches that could improve performance of the frequency standard substantially.

  7. Absolute frequency measurement of unstable lasers with optical frequency combs

    Science.gov (United States)

    Beverini, N.; Poli, N.; Sutyrin, D.; Wang, F.-Y.; Schioppo, M.; Tarallo, M. G.; Tino, G. M.

    2010-09-01

    Here we report on absolute frequency measurements of a commercial high power CW diode-pumped solid-state laser (Coherent Verdi-V5). This kind of lasers usually presents large frequency jitter (up to 50 MHz) both in the short term (1 ms time scale) and in the long term (>10 s time scale). A precise measurement of absolute frequency deviations in both temporal scales should require a set of different devices (optical cavities, optical wave-meters), each suited for measurements only at a specific integration time. Here we demonstrate how a frequency comb can be used to overcome this difficulty, allowing in a single step a full characterization of both short ( 103 s) absolute frequency jitter with a resolution better than 1 MHz. We demonstrate in this way the flexibility of optical frequency combs for absolute frequency measurements not only of ultra-stable lasers but also of relatively unstable lasers. The absolute frequency calibration of the Verdi laser that we have obtained have been used in order to improve the accuracy of the measurements of the local gravitational acceleration value with 88Sr atoms trapped in 1D vertical lattices.

  8. Frequency domain analysis of triggered lightning return stroke luminosity velocity

    Science.gov (United States)

    Carvalho, F. L.; Uman, M. A.; Jordan, D. M.; Moore, R. C.

    2017-02-01

    Fourier analysis is applied to time domain return stroke luminosity signals to calculate the phase and group velocities and the amplitude of the luminosity signals as a function of frequency measured between 4 m and 115 m during 12 triggered lightning strokes. We show that pairs of time domain luminosity signals measured at different heights can be interpreted as the input and the output of a system whose frequency domain transfer function can be determined from the measured time domain signals. From the frequency domain transfer function phase we find the phase and group velocities, and luminosity amplitude as a function of triggered lightning channel height and signal frequency ranging from 50 kHz to 300 kHz. We show that higher-frequency luminosity components propagate faster than the lower frequency components and that higher-frequency luminosity components attenuate more rapidly than lower frequency components. Finally, we calculate time domain return stroke velocities as a function of channel height using two time delay techniques: (1) measurement at the 20% amplitude level and (2) cross correlation.

  9. Imaging scattering orientation with spatial frequency domain imaging.

    Science.gov (United States)

    Konecky, Soren D; Rice, Tyler; Durkin, Anthony J; Tromberg, Bruce J

    2011-12-01

    Optical imaging techniques based on multiple light scattering generally have poor sensitivity to the orientation and direction of microscopic light scattering structures. In order to address this limitation, we introduce a spatial frequency domain method for imaging contrast from oriented scattering structures by measuring the angular-dependence of structured light reflectance. The measurement is made by projecting sinusoidal patterns of light intensity on a sample, and measuring the degree to which the patterns are blurred as a function of the projection angle. We derive a spatial Fourier domain solution to an anisotropic diffusion model. This solution predicts the effects of bulk scattering orientation on the amplitude and phase of the projected patterns. We introduce a new contrast function based on a scattering orientation index (SOI) which is sensitive to the degree to which light scattering is directionally dependent. We validate the technique using tissue simulating phantoms, and ex vivo samples of muscle and brain. Our results show that SOI is independent of the overall amount of bulk light scattering and absorption, and that isotropic versus oriented scattering structures can be clearly distinguished. We determine the orientation of subsurface microscopic scattering structures located up to 600 μm beneath highly scattering (μ(') (s) = 1.5 mm(-1)) material.

  10. Evaluation of Damping Using Frequency Domain Operational Modal Analysis Techniques

    DEFF Research Database (Denmark)

    Bajric, Anela; Georgakis, Christos T.; Brincker, Rune

    2015-01-01

    Operational Modal Analysis (OMA) techniques provide in most cases reasonably accurate estimates of structural frequencies and mode shapes. In contrast though, they are known to often produce uncertain structural damping estimates, which is mainly due to inherent random and/or bias errors...... domain techniques, the Frequency Domain Decomposition (FDD) and the Frequency Domain Polyreference (FDPR). The response of a two degree-of-freedom (2DOF) system is numerically established with specified modal parameters subjected to white noise loading. The system identification is evaluated with well...

  11. High frequency optical pulse generation by frequency doubling using polarization rotation

    Science.gov (United States)

    Liu, Yang

    2016-05-01

    In this work, we propose and experimentally characterize a stable 40 GHz optical pulse generation by frequency doubling using polarization rotation in a phase modulator (PM). Only half the electrical driving frequency is required (i.e. 20 GHz); hence the deployment cost can be reduced. Besides, precise control of the bias of the PM is not required. The generated optical pulses have a high center-mode-suppression-ratio (CMSR) of  >  28 dB. The single sideband (SSB) noise spectrum is also measured, and the time-domain waveforms under different CMSRs are also analyzed and discussed.

  12. Optical Adaptive Filter. Frequency Domain Implementation.

    Science.gov (United States)

    1983-12-01

    my advisor. Also, I thank Dr. Matt Kabrisky and Maj. Ken Castor for their expert advice. Finally, without the administrative support of Miriam and...the OSP principies of Fig. 19, see page 141 of Ref. 22. Bragg cell 1 Bragg cell 2 OPTICS• -:1b I Cos W t -I" c lectrooptic . odulator Photomulti

  13. On Frequency Domain Models for TDOA Estimation

    DEFF Research Database (Denmark)

    Jensen, Jesper Rindom; Nielsen, Jesper Kjær; Christensen, Mads Græsbøll

    2015-01-01

    of a much more general method. In this connection, we establish the conditions under which the cross-correlation method is a statistically efficient estimator. One of the conditions is that the source signal is periodic with a known fundamental frequency of 2π/N radians per sample, where N is the number...

  14. Analysis of wave packet motion in frequency and time domain: oxazine 1.

    Science.gov (United States)

    Braun, Markus; Sobotta, Constanze; Dürr, Regina; Pulvermacher, Horst; Malkmus, Stephan

    2006-08-17

    Wave packet motion in the laser dye oxazine 1 in methanol is investigated by spectrally resolved transient absorption spectroscopy. The spectral range of 600-690 nm was accessible by amplified broadband probe pulses covering the overlap region of ground-state bleach and stimulated emission signal. The influence of vibrational wave packets on the optical signal is analyzed in the frequency domain and the time domain. For the analysis in the frequency domain an algorithm is presented that accounts for interference effects of neighbored vibrational modes. By this method amplitude, phase and decay time of vibrational modes are retrieved as a function of probe wavelength and distortions due to neighbored modes are reduced. The analysis of the data in the time domain yields complementary information on the intensity, central wavelength, and spectral width of the optical bleach spectrum due to wave packet motion.

  15. Fractional Fourier transform for partially coherent beam in spatial-frequency domain

    Institute of Scientific and Technical Information of China (English)

    Cai Yang-Jian; Lin Qiang

    2004-01-01

    By using Fourier transform and the tensor analysis method, the fractional Fourier transform (FRT) in the spatialfrequency domain for partially coherent beams is derived. Based on the FRT in the spatial-frequency domain, an analytical transform formula is derived for a partially coherent twisted anisotropic Gaussian-Schell model (GSM) beam passing through the FRT system. The connections between the FRT formula and the generalized diffraction integral formulae for partially coherent beams through an aligned optical system and a misaligned optical system in the spatialfrequency domain are discussed, separately. By using the derived formula, the intensity distribution of partially coherent twisted anisotropic GSM beams in the FRT plane are studied in detail. The formula derived provide a convenient tool for analysing and calculating the FRTs of the partially coherent beams in spatial-frequency domain.

  16. Causality between Regional Stock Markets: A Frequency Domain Approach

    National Research Council Canada - National Science Library

    Nikola Gradojevic; Eldin Dobardzic

    2013-01-01

    ...), this paper presents a frequency domain analysis of a causal relationship between the returns on the CROBEX, SBITOP, CETOP and DAX indices, and the return on the major Serbian stock exchange index, BELEX 15...

  17. Silicon-Chip-Based Optical Frequency Combs

    Science.gov (United States)

    2015-10-26

    frequencies . This phenomenon appears in many systems spanning biology, chemistry, neuroscience, and physics [29,30]. Examples include power grid networks... Frequency Combs," Phys. Rev. Lett. 100, 013902 (2008). [91] F. Leo, et al., “Dispersive wave emission and supercontinuum generation in a silicon wire...AFRL-AFOSR-VA-TR-2015-0365 Silicon-Chip-Based Optical Frequency Combs Alexander Gaeta CORNELL UNIVERSITY Final Report 10/26/2015 DISTRIBUTION A

  18. Robust time and frequency domain estimation methods in adaptive control

    Science.gov (United States)

    Lamaire, Richard Orville

    1987-01-01

    A robust identification method was developed for use in an adaptive control system. The type of estimator is called the robust estimator, since it is robust to the effects of both unmodeled dynamics and an unmeasurable disturbance. The development of the robust estimator was motivated by a need to provide guarantees in the identification part of an adaptive controller. To enable the design of a robust control system, a nominal model as well as a frequency-domain bounding function on the modeling uncertainty associated with this nominal model must be provided. Two estimation methods are presented for finding parameter estimates, and, hence, a nominal model. One of these methods is based on the well developed field of time-domain parameter estimation. In a second method of finding parameter estimates, a type of weighted least-squares fitting to a frequency-domain estimated model is used. The frequency-domain estimator is shown to perform better, in general, than the time-domain parameter estimator. In addition, a methodology for finding a frequency-domain bounding function on the disturbance is used to compute a frequency-domain bounding function on the additive modeling error due to the effects of the disturbance and the use of finite-length data. The performance of the robust estimator in both open-loop and closed-loop situations is examined through the use of simulations.

  19. Estimation of luminescence lifetime in frequency domain

    Institute of Scientific and Technical Information of China (English)

    Zhang Fu-Jun; Xu Zheng; Zhao Su-Ling; Lou Zhi-Dong; Yang Sheng-Yi; Xu Xu-Rong

    2006-01-01

    Absorption is the origin of luminescence. But it must be noticed that the lifetime of luminescence might reversely influence the rate of absorption. In this paper, it is reported that the luminescence intensity of copper and manganese changes with the driving frequency at constant voltage. The variation of luminescent intensity depends only on the lifetime of luminescence but not on the type of quenching or other factors. Generally the rate of absorption is dominantly determined by the material property and the lifetime of luminescence centres, the absorption of shorter lifetime centre will be larger than that of the longer lifetime centre at the same excited condition.

  20. Kerr optical frequency combs: theory, applications and perspectives

    Science.gov (United States)

    Chembo, Yanne K.

    2016-06-01

    The optical frequency comb technology is one of the most important breakthrough in photonics in recent years. This concept has revolutionized the science of ultra-stable lightwave and microwave signal generation. These combs were originally generated using ultrafast mode-locked lasers, but in the past decade, a simple and elegant alternativewas proposed,which consisted in pumping an ultra-high-Q optical resonator with Kerr nonlinearity using a continuous-wave laser. When optimal conditions are met, the intracavity pump photons are redistributed via four-wave mixing to the neighboring cavity modes, thereby creating the so-called Kerr optical frequency comb. Beyond being energy-efficient, conceptually simple, and structurally robust, Kerr comb generators are very compact devices (millimetric down to micrometric size) which can be integrated on a chip. They are, therefore, considered as very promising candidates to replace femtosecond mode-locked lasers for the generation of broadband and coherent optical frequency combs in the spectral domain, or equivalently, narrow optical pulses in the temporal domain. These combs are, moreover, expected to provide breakthroughs in many technological areas, such as integrated photonics, metrology, optical telecommunications, and aerospace engineering. The purpose of this review article is to present a comprehensive survey of the topic of Kerr optical frequency combs.We provide an overview of the main theoretical and experimental results that have been obtained so far. We also highlight the potential of Kerr combs for current or prospective applications, and discuss as well some of the open challenges that are to be met at the fundamental and applied level.

  1. Kerr optical frequency combs: theory, applications and perspectives

    Directory of Open Access Journals (Sweden)

    Chembo Yanne K.

    2016-06-01

    Full Text Available The optical frequency comb technology is one of the most important breakthrough in photonics in recent years. This concept has revolutionized the science of ultra-stable lightwave and microwave signal generation. These combs were originally generated using ultrafast mode-locked lasers, but in the past decade, a simple and elegant alternativewas proposed,which consisted in pumping an ultra-high-Q optical resonator with Kerr nonlinearity using a continuous-wave laser. When optimal conditions are met, the intracavity pump photons are redistributed via four-wave mixing to the neighboring cavity modes, thereby creating the so-called Kerr optical frequency comb. Beyond being energy-efficient, conceptually simple, and structurally robust, Kerr comb generators are very compact devices (millimetric down to micrometric size which can be integrated on a chip. They are, therefore, considered as very promising candidates to replace femtosecond mode-locked lasers for the generation of broadband and coherent optical frequency combs in the spectral domain, or equivalently, narrow optical pulses in the temporal domain. These combs are, moreover, expected to provide breakthroughs in many technological areas, such as integrated photonics, metrology, optical telecommunications, and aerospace engineering. The purpose of this review article is to present a comprehensive survey of the topic of Kerr optical frequency combs.We provide an overview of the main theoretical and experimental results that have been obtained so far. We also highlight the potential of Kerr combs for current or prospective applications, and discuss as well some of the open challenges that are to be met at the fundamental and applied level.

  2. Conversion of Dielectric Data from the Time Domain to the Frequency Domain

    Directory of Open Access Journals (Sweden)

    Vladimir Durman

    2005-01-01

    Full Text Available Polarisation and conduction processes in dielectric systems can be identified by the time domain or the frequency domain measurements. If the systems is a linear one, the results of the time domain measurements can be transformed into the frequency domain, and vice versa. Commonly, the time domain data of the absorption conductivity are transformed into the frequency domain data of the dielectric susceptibility. In practice, the relaxation are mainly evaluated by the frequency domain data. In the time domain, the absorption current measurement were prefered up to now. Recent methods are based on the recovery voltage measurements. In this paper a new method of the recovery data conversion from the time the frequency domain is proposed. The method is based on the analysis of the recovery voltage transient based on the Maxwell equation for the current density in a dielectric. Unlike the previous published solutions, the Laplace fransform was used to derive a formula suitable for practical purposes. the proposed procedure allows also calculating of the insulation resistance and separating the polarisation and conduction losses.

  3. Optical frequency standards for time and length applications

    Science.gov (United States)

    Hong, Feng-Lei

    2017-01-01

    The last decade has witnessed tremendous progress in research on optical frequency metrology. Optical frequency standards using optical lattice and single-ion trap technologies have reached levels of stability and accuracy that surpass the performance of the best Cs fountain atomic clocks by orders of magnitude. Optical frequency standards are also used for various applications including length metrology. Optical frequency measurement and links using optical frequency combs and optical fibres play important roles in the development of optical frequency standards. This article introduces optical frequency standards recommended by the International Committee for Weights and Measures (CIPM) along with updates provided by recent research results. Frequency ratio measurements and remote frequency comparisons are addressed in relation to the work whose goal is to redefine the second. Optical frequency standard and optical frequency comb applications are also described.

  4. Slow light based optical frequency shifter

    CERN Document Server

    Li, Qian; Thuresson, Axel; Nilsson, Adam N; Rippe, Lars; Kröll, Stefan

    2016-01-01

    We demonstrate experimentally and theoretically a controllable way of shifting the frequency of an optical pulse by using a combination of spectral hole burning, slow light effect, and linear Stark effect in a rare-earth-ion doped crystal. We claim that the solid angle of acceptance of a frequency shift structure can be close to $2\\pi$, which means that the frequency shifter could work not only for optical pulses propagating in a specific spatial mode but also for randomly scattered light. As the frequency shift is controlled solely by an external electric field, it works also for weak coherent light fields, and can e.g. be used as a frequency shifter for quantum memory devices in quantum communication.

  5. Error Analysis in Frequency Domain for Linear Multipass Algorithms

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Error analysis methods in frequency domain are developed in this paper for determining the characteristic root and transfer function errors when the linear multipass algorithms are used to solve linear differential equations.the relation between the local truncation error in time domain and the error in frequency domain is established, which is the basis for developing the error estimation methods. The error estimation methods for the digital simulation model constructed by using the Runge-Kutta algorithms and the linear multistep predictor-corrector algorithms are also given.

  6. A microresonator frequency comb optical clock

    CERN Document Server

    Papp, Scott B; DelHaye, Pascal; Quinlan, Franklyn; Lee, Hansuek; Vahala, Kerry J; Diddams, Scott A

    2013-01-01

    Optical-frequency combs enable measurement precision at the 20th digit, and accuracy entirely commensurate with their reference oscillator. A new direction in experiments is the creation of ultracompact frequency combs by way of nonlinear parametric optics in microresonators. We refer to these as microcombs, and here we report a silicon-chip-based microcomb optical clock that phase-coherently converts an optical-frequency reference to a microwave signal. A low-noise comb spectrum with 25 THz span is generated with a 2 mm diameter silica disk and broadening in nonlinear fiber. This spectrum is stabilized to rubidium frequency references separated by 3.5 THz by controlling two teeth 108 modes apart. The optical clocks output is the electronically countable 33 GHz microcomb line spacing, which features an absolute stability better than the rubidium transitions by the expected factor of 108. Our work demonstrates the comprehensive set of tools needed for interfacing microcombs to state-of-the-art optical clocks.

  7. Time delay measurement in the frequency domain

    Science.gov (United States)

    Durbin, Stephen M.; Liu, Shih-Chieh; Dufresne, Eric M.; Li, Yuelin; Wen, Haidan

    2015-01-01

    Pump–probe studies at synchrotrons using X-ray and laser pulses require accurate determination of the time delay between pulses. This becomes especially important when observing ultrafast responses with lifetimes approaching or even less than the X-ray pulse duration (∼100 ps). The standard approach of inspecting the time response of a detector sensitive to both types of pulses can have limitations due to dissimilar pulse profiles and other experimental factors. Here, a simple alternative is presented, where the frequency response of the detector is monitored versus time delay. Measurements readily demonstrate a time resolution of ∼1 ps. Improved precision is possible by simply extending the data acquisition time. PMID:26289282

  8. Revealing Carrier-Envelope Phase through Frequency Mixing and Interference in Frequency Resolved Optical Gating

    CERN Document Server

    Snedden, Edward W; Jamison, Steven P

    2015-01-01

    We demonstrate that full temporal characterisation of few-cycle electromagnetic pulses, including retrieval of the carrier envelope phase (CEP), can be directly obtained from Frequency Resolved Optical Gating (FROG) techniques in which the interference between non-linear frequency mixing processes is resolved. We derive a framework for this scheme, defined Real Domain-FROG (ReD-FROG), as applied to the cases of interference between sum and difference frequency components and between fundamental and sum/difference frequency components. A successful numerical demonstration of ReD-FROG as applied to the case of a self-referenced measurement is provided. A proof-of-principle experiment is performed in which the CEP of a single-cycle THz pulse is accurately obtained and demonstrates the possibility for THz detection beyond the bandwidth limitations of electro-optic sampling.

  9. Propagation of Partially Coherent Twisted Anisotropic Gaussian-Schell Model Beams in the Spatial-Frequency Domain

    Institute of Scientific and Technical Information of China (English)

    蔡阳健; 林强

    2002-01-01

    The generalized Collins formula for partially coherent beams through axially non-symmetrical optical systems in the spatial-frequency domain is derived by means of the tensor method. Based on this formula, the tensor ABCD law in the spatial-frequency domain for partially coherent twisted anisotropic Gaussian-Schell model (GSM) beams is derived, which governs the transformation of the twisted anisotropic GSM beams in the spatialfrequency domain. An example of an application is provided.

  10. Evaluation of the influence of cardiac motion on the accuracy and reproducibility of longitudinal measurements and the corresponding image quality in optical frequency domain imaging: an ex vivo investigation of the optimal pullback speed.

    Science.gov (United States)

    Koyama, Kohei; Yoneyama, Kihei; Mitarai, Takanobu; Kuwata, Shingo; Kongoji, Ken; Harada, Tomoo; Akashi, Yoshihiro J

    2015-08-01

    Longitudinal measurement using intravascular ultrasound is limited because the motorized pullback device assumes no cardiac motion. A newly developed intracoronary imaging modality, optical frequency domain imaging (OFDI), has higher resolution and an increased auto-pullback speed with presumably lesser susceptibility to cardiac motion artifacts during pullback for longitudinal measurement; however, it has not been fully investigated. We aimed to clarify the influence of cardiac motion on the accuracy and reproducibility of longitudinal measurements obtained using OFDI and to determine the optimal pullback speed. This ex vivo study included 31 stents deployed in the mid left anterior descending artery under phantom heartbeat and coronary flow simulation. Longitudinal stent lengths were measured twice using OFDI at three pullback speeds. Differences in stent lengths between OFDI and microscopy and between two repetitive pullbacks were assessed to determine accuracy and reproducibility. Furthermore, three-dimensional (3D) reconstruction was used for evaluating image quality. With regard to differences in stent length between OFDI and microscopy, the intraclass correlation coefficient values were 0.985, 0.994, and 0.995 at 10, 20, and 40 mm/s, respectively. With regard to reproducibility, the values were 0.995, 0.996, and 0.996 at 10, 20, and 40 mm/s, respectively. 3D reconstruction showed a superior image quality at 10 and 20 mm/s compared with that at 40 mm/s. OFDI demonstrated high accuracy and reproducibility for longitudinal stent measurements. Moreover, its accuracy and reproducibility were remarkable at a higher pullback speed. A 20-mm/s pullback speed may be optimal for clinical and research purposes.

  11. An Improved Traffic Matrix Decomposition Method with Frequency Domain Regularization

    CERN Document Server

    Wang, Zhe; Yin, Baolin

    2012-01-01

    In this letter, we propose a novel network traffic matrix decomposition method named as Stable Principal Component Pursuit with Frequency Domain Regularization (SPCP-FDR). SPCP-FDR improves the Stable Principal Component Pursuit (SPCP) method by using a new noise regularization function defined in frequency domain. Compared with SPCP, SPCP-FDR is more adaptive to empirical frequency properties of diverse traffic components. The Accelerated Proximal Gradient (APG) algorithm for SPCP-FDR is presented. Our experiment results demonstrate the rationality of this new method.

  12. Audio frequency in vivo optical coherence elastography

    Energy Technology Data Exchange (ETDEWEB)

    Adie, Steven G; Kennedy, Brendan F; Armstrong, Julian J; Alexandrov, Sergey A; Sampson, David D [Optical-Biomedical Engineering Laboratory (OBEL), School of Electrical, Electronic and Computer Engineering, University of Western Australia, 35 Stirling Highway, Crawley, Western Australia 6009 (Australia)], E-mail: dsampson@ee.uwa.edu.au

    2009-05-21

    We present a new approach to optical coherence elastography (OCE), which probes the local elastic properties of tissue by using optical coherence tomography to measure the effect of an applied stimulus in the audio frequency range. We describe the approach, based on analysis of the Bessel frequency spectrum of the interferometric signal detected from scatterers undergoing periodic motion in response to an applied stimulus. We present quantitative results of sub-micron excitation at 820 Hz in a layered phantom and the first such measurements in human skin in vivo.

  13. In vivo spatial frequency domain spectroscopy of two layer media

    Science.gov (United States)

    Yudovsky, Dmitry; Nguyen, John Quan M.; Durkin, Anthony J.

    2012-10-01

    Monitoring of tissue blood volume and local oxygen saturation can inform the assessment of tissue health, healing, and dysfunction. These quantities can be estimated from the contribution of oxyhemoglobin and deoxyhemoglobin to the absorption spectrum of the dermis. However, estimation of blood related absorption in skin can be confounded by the strong absorption of melanin in the epidermis and epidermal thickness and pigmentation varies with anatomic location, race, gender, and degree of disease progression. Therefore, a method is desired that decouples the effect of melanin absorption in the epidermis from blood absorption in the dermis for a large range of skin types and thicknesses. A previously developed inverse method based on a neural network forward model was applied to simulated spatial frequency domain reflectance of skin for multiple wavelengths in the near infrared. It is demonstrated that the optical thickness of the epidermis and absorption and reduced scattering coefficients of the dermis can be determined independently and with minimal coupling. Then, the same inverse method was applied to reflectance measurements from a tissue simulating phantom and in vivo human skin. Oxygen saturation and total hemoglobin concentrations were estimated from the volar forearms of weakly and strongly pigmented subjects using a standard homogeneous model and the present two layer model.

  14. Snapshot Spectral Domain Optical Coherence Tomography

    Science.gov (United States)

    Valdez, Ashley

    Optical coherence tomography systems are used to image the retina in 3D to allow ophthalmologists diagnose ocular disease. These systems yield large data sets that are often labor-intensive to analyze and require significant expertise in order to draw conclusions, especially when used over time to monitor disease progression. Spectral Domain Optical Coherence Tomography (SD-OCT) instantly acquires depth profiles at a single location with a broadband source. These systems require mechanical scanning to generate two- or three-dimensional images. Instead of mechanically scanning, a beamlet array was used to permit multiple depth measurements on the retina with a single snapshot using a 3x 3 beamlet array. This multi-channel system was designed, assembled, and tested using a 1 x 2 beamlet lens array instead of a 3 x 3 beamlet array as a proof of concept prototype. The source was a superluminescent diode centered at 840nm with a 45nm bandwidth. Theoretical axial resolution was 6.92um and depth of focus was 3.45mm. Glass samples of varying thickness ranging from 0.18mm to 1.14mm were measured with the system to validate that correct depth profiles can be acquired for each channel. The results demonstrated the prototype system performed as expected, and is ready to be modified for in vivo applicability.

  15. Design PID controllers for desired time-domain or frequency-domain response.

    Science.gov (United States)

    Zhang, Weidong; Xi, Yugeng; Yang, Genke; Xu, Xiaoming

    2002-10-01

    Practical requirements on the design of control systems, especially process control systems, are usually specified in terms of time-domain response, such as overshoot and rise time, or frequency-domain response, such as resonance peak and stability margin. Although numerous methods have been developed for the design of the proportional-integral-derivative (PID) controller, little work has been done in relation to the quantitative time-domain and frequency-domain responses. In this paper, we study the following problem: Given a nominal stable process with time delay, we design a suboptimal PID controller to achieve the required time-domain response or frequency-domain response for the nominal system or the uncertain system. An H(infinity) PID controller is developed based on optimal control theory and the parameters are derived analytically. Its properties are investigated and compared with that of two developed suboptimal controllers: an H2 PID controller and a Maclaurin PID controller. It is shown that all three controllers can provide the quantitative time-domain and frequency-domain responses.

  16. Examining thermal transport through a frequency-domain representation of time-domain thermoreflectance data.

    Science.gov (United States)

    Collins, Kimberlee C; Maznev, Alexei A; Cuffe, John; Nelson, Keith A; Chen, Gang

    2014-12-01

    Laser-based time-domain thermoreflectance (TDTR) and frequency-domain thermoreflectance (FDTR) techniques are widely used for investigating thermal transport at micro- and nano-scales. We demonstrate that data obtained in TDTR measurements can be represented in a frequency-domain form equivalent to FDTR, i.e., in the form of a surface temperature amplitude and phase response to time-harmonic heating. Such a representation is made possible by using a large TDTR delay time window covering the entire pulse repetition interval. We demonstrate the extraction of frequency-domain data up to 1 GHz from TDTR measurements on a sapphire sample coated with a thin layer of aluminum, and show that the frequency dependencies of both the amplitude and phase responses agree well with theory. The proposed method not only allows a direct comparison of TDTR and FDTR data, but also enables measurements at high frequencies currently not accessible to FDTR. The frequency-domain representation helps uncover aspects of the measurement physics which remain obscured in a traditional TDTR measurement, such as the importance of modeling the details of the heat transport in the metal transducer film for analyzing high frequency responses.

  17. Optical lattice clocks and frequency comparison

    Energy Technology Data Exchange (ETDEWEB)

    Katori, Hidetoshi; Takano, Tetsushi; Takamoto, Masao, E-mail: katori@amo.t.u-tokyo.ac.jp [Department of Applied Physics, University of Tokyo, Tokyo (Japan); CREST, Japan Science and Technology Agency, Saitama (Japan)

    2011-01-10

    We consider designs of optical lattice clocks in view of the quantum statistics, relevant atomic spins, and atom-lattice interactions. The first two issues lead to two optimal constructions for the clock: a one-dimensional (1D) optical lattice loaded with spin-polarized fermions and a 3D optical lattice loaded with bosons. By taking atomic multipolar interactions with the lattice fields into account, an 'atomic motion insensitive' wavelength is proposed to provide a precise definition of the 'magic wavelength'. We then present a frequency comparison of these two optical lattice clocks: spin-polarized fermionic {sup 87}Sr and bosonic {sup 88}Sr prepared in 1D and 3D optical lattices, respectively. Synchronous interrogations of these two optical lattice clocks by the same probe laser allowed canceling out its frequency noise as a common mode noise to achieve a relative stability of 3x10{sup -17} for an averaging time of {tau} = 350 s. The scheme, therefore, provides us with a powerful means to investigate intrinsic uncertainty of the clocks regardless of the probe laser stability. We discuss prospects of the synchronous operation of the clocks on the measurement of the geoid height difference and on the search of constancy of fundamental constants.

  18. Functional cerebral activation detected by frequency-domain near-infrared spectroscopy

    Science.gov (United States)

    Toronov, Vladislav Y.; Webb, Andrew G.; Choi, Jee H.; Wolf, Martin; Safonova, Larisa P.; Wolf, Ursula; Gratton, Enrico

    2002-07-01

    The aim of our study was to explore the possibility of detecting haemodynamic changes in the brain using frequency- domain near-IR spectroscopy by exploiting the phase of the intensity modulated optical signal. To obtain optical signals with eh highest possible signal-to-noise ratio, we performed simultaneous NIRS-fMRI measurements, with subsequent correlation of the time courses of both measurements. The cognitive paradigm used arithmetic calculations, with optical signals acquired with sensors placed on the forehead. In three subjects we demonstrated correlation between the haemodynamic signals obtained using NIRS and BOLD fMRI.

  19. An operational modal analysis method in frequency and spatial domain

    Science.gov (United States)

    Wang, Tong; Zhang, Lingmi; Tamura, Yukio

    2005-12-01

    A frequency and spatial domain decomposition method (FSDD) for operational modal analysis (OMA) is presented in this paper, which is an extension of the complex mode indicator function (CMIF) method for experimental modal analysis (EMA). The theoretical background of the FSDD method is clarified. Singular value decomposition is adopted to separate the signal space from the noise space. Finally, an enhanced power spectrum density (PSD) is proposed to obtain more accurate modal parameters by curve fitting in the frequency domain. Moreover, a simulation case and an application case are used to validate this method.

  20. An operational modal analysis method in frequency and spatial domain

    Institute of Scientific and Technical Information of China (English)

    Wang Tong; Zhang Lingmi; Tamura Yukio

    2005-01-01

    A frequency and spatial domain decomposition method (FSDD) for operational modal analysis (OMA) is presented in this paper, which is an extension of the complex mode indicator function (CMIF) method for experimental modal analysis (EMA). The theoretical background of the FSDD method is clarified. Singular value decomposition is adopted to separate the signal space from the noise space. Finally, an enhanced power spectrum density (PSD) is proposed to obtain more accurate modal parameters by curve fitting in the frequency domain. Moreover, a simulation case and an application case are used to validate this method.

  1. Frequency domain simultaneous algebraic reconstruction techniques: algorithm and convergence

    Science.gov (United States)

    Wang, Jiong; Zheng, Yibin

    2005-03-01

    We propose a simultaneous algebraic reconstruction technique (SART) in the frequency domain for linear imaging problems. This algorithm has the advantage of efficiently incorporating pixel correlations in an a priori image model. First it is shown that the generalized SART algorithm converges to the weighted minimum norm solution of a weighted least square problem. Then an implementation in the frequency domain is described. The performance of the new algorithm is demonstrated with fan beam computed tomography (CT) examples. Compared to the traditional SART and its major alternative ART, the new algorithm offers superior image quality and potential application to other modalities.

  2. Finite-Difference Frequency-Domain Method in Nanophotonics

    DEFF Research Database (Denmark)

    Ivinskaya, Aliaksandra

    is often indispensable. This thesis presents the development of rigorous finite-difference method, a very general tool to solve Maxwell’s equations in arbitrary geometries in three dimensions, with an emphasis on the frequency-domain formulation. Enhanced performance of the perfectly matched layers...... is obtained through free space squeezing technique, and nonuniform orthogonal grids are built to greatly improve the accuracy of simulations of highly heterogeneous nanostructures. Examples of the use of the finite-difference frequency-domain method in this thesis range from simulating localized modes...

  3. Microresonator-based optical frequency combs.

    Science.gov (United States)

    Kippenberg, T J; Holzwarth, R; Diddams, S A

    2011-04-29

    The series of precisely spaced, sharp spectral lines that form an optical frequency comb is enabling unprecedented measurement capabilities and new applications in a wide range of topics that include precision spectroscopy, atomic clocks, ultracold gases, and molecular fingerprinting. A new optical frequency comb generation principle has emerged that uses parametric frequency conversion in high resonance quality factor (Q) microresonators. This approach provides access to high repetition rates in the range of 10 to 1000 gigahertz through compact, chip-scale integration, permitting an increased number of comb applications, such as in astronomy, microwave photonics, or telecommunications. We review this emerging area and discuss opportunities that it presents for novel technologies as well as for fundamental science.

  4. A Visible Watermarking Scheme for Digital Images in Frequency Domain

    Directory of Open Access Journals (Sweden)

    D.R.Denslin Brabin

    2012-11-01

    Full Text Available A novel method is proposed for visible watermarking of digital image in frequency domain. The method is based on DCT modification of original image with respect to watermark image. The host image pixels are transformed into frequency coefficients as well as the watermark image pixels are also transformed into frequency coefficients using DCT. The compound mapping function is used to adjust the pixel values close to those of desired visible watermarks. Thus the watermarking is done in frequency domain using compound mapping function. One who has the watermark image and mapping function parameters only can remove the watermark. Thus it enhances the security. Experimental results demonstrate the effectiveness of the proposed approach.

  5. A proposed fibre optic time domain optical coherence tomography system using a micro-photonic stationary optical delay line

    Science.gov (United States)

    Jansz, Paul Vernon; Wild, Graham; Hinckley, Steven

    2008-04-01

    Conventional time domain Optical Coherence Tomography (OCT) relies on a reference Optical Delay Line (ODL). These reference ODLs require the physical movement of a mirror to scan a given depth range. This movement results in instrument degradation. We propose a new optical fibre based time domain OCT system that makes use of a micro-photonic structure as a stationary ODL. The proposed system uses an in-fibre interferometer, either a Michelson or a Mach-Zhender. The reference ODL makes use of a collimator to expand the light from the optical fibre. This is them expanded in one dimension via planar optics, that is, a cylindrical lens based telescope, using a concave and convex lens. The expanded beam is them passed through a transmissive Spatial Light Modulator (SLM), specifically a liquid crystal light valve used as an optical switch. Light is then reflected back through the system off the micro-photonic structure. The micro-photonic structure is a one dimensional array of stagged mirror steps, called a Stepped Mirror Structure (SMS). The system enables the selection of discrete optical delay lengths. The proposed ODL is capable of depth hoping and multicasting. We discuss the fabrication of the SMS, which consists of eight steps, each approximately 150 μm high. A change in notch frequency using an in-fibre Mach Zhender interferometer was used to gauge the average step height. The results gave an average step height of 146 μm.

  6. Microwave signal processing in two-frequency domain for ROF systems implementation: training course

    Science.gov (United States)

    Morozov, Oleg G.; Morozov, Gennady A.

    2014-04-01

    This article is presented materials from two tutorials: "Optical two-frequency domain reflectometry1, 2" and "Microwave technologies in industry, living systems and telecommunications3". These materials were prepared for master training courses and listed in the "SPIE Optical Education Directory" for 2013/2014. The main its theme is microwave photonics. Microwave photonics has been defined as the study of photonic devices operating at microwave frequencies and their application to microwave and optical systems. Its initial rationale was to use the advantages of photonic technologies to provide functions in microwave systems that are very complex or even impossible to carry out directly in the radiofrequency domain. But microwave photonics is also succeeding in incorporating a variety of techniques used in microwave engineering to improve the performance of photonic communication networks and systems. Three parts of this chapter are devoted to applications and construction principles of systems forming microwave photonic filters, measuring instantaneous frequency of microwave heterodyne signals and characterizing stimulated Mandelstam- Brillouin scattering spectrum in ROF systems. The main emphasis is on the use of the two-frequency symmetric radiation, generated by the Il'in-Morozov's method4, in given systems. It is forming radiation for the synthesis of optical filters coefficients, it's application and processing determine the increase in the signal-to-noise ratio during heterodyne frequencies monitoring and characterization of nonlinear effects spectrum.

  7. Optical-domain Compensation for Coupling between Optical Fiber Conjugate Vortex Modes

    DEFF Research Database (Denmark)

    Lyubopytov, Vladimir S.; Tatarczak, Anna; Lu, Xiaofeng

    2016-01-01

    We demonstrate for the first time optical-domain compensation for coupling between conjugate vortex modes in optical fibers. We introduce a novel method for reconstructing the complex propagation matrix of the optical fiber with straightforward implementation....

  8. Building the analytical response in frequency domain of AC biased bolometers. Application to Planck/HFI

    Science.gov (United States)

    Sauvé, Alexandre; Montier, Ludovic

    2016-12-01

    Context: Bolometers are high sensitivity detector commonly used in Infrared astronomy. The HFI instrument of the Planck satellite makes extensive use of them, but after the satellite launch two electronic related problems revealed critical. First an unexpected excess response of detectors at low optical excitation frequency for ν linearized versions of the bolometer electro thermal equilibrium. A custom description of signals in frequency is used to solve the problem with linear algebra. The model performances is validated using time domain simulations. Results: The provided expression is suitable for calibration and data processing. It can also be used to provide constraints for fitting optical transfer function using real data from steady state electronic response and optical response. The accurate description of electronic response can also be used to improve the ADC nonlinearity correction for quickly varying optical signals.

  9. Modal Identification from Ambient Responses Using Frequency Domain Decomposition

    DEFF Research Database (Denmark)

    Brincker, Rune; Zhang, Lingmi; Andersen, Palle

    2000-01-01

    In this paper a new frequency domain technique is introduced for the modal identification from ambient responses, i.e. in the case where the modal parameters must be estimated without knowing the input exciting the system. By its user friendliness the technique is closely related to the classical...

  10. Modal Identification from Ambient Responses using Frequency Domain Decomposition

    DEFF Research Database (Denmark)

    Brincker, Rune; Zhang, L.; Andersen, P.

    2000-01-01

    In this paper a new frequency domain technique is introduced for the modal identification from ambient responses, ie. in the case where the modal parameters must be estimated without knowing the input exciting the system. By its user friendliness the technique is closely related to the classical...

  11. A Frequency Domain Design Method For Sampled-Data Compensators

    DEFF Research Database (Denmark)

    Niemann, Hans Henrik; Jannerup, Ole Erik

    1990-01-01

    A new approach to the design of a sampled-data compensator in the frequency domain is investigated. The starting point is a continuous-time compensator for the continuous-time system which satisfy specific design criteria. The new design method will graphically show how the discrete...

  12. Frequency-domain thermal modelling of power semiconductor devices

    DEFF Research Database (Denmark)

    Ma, Ke; Blaabjerg, Frede; Andresen, Markus

    2015-01-01

    to correctly predict the device temperatures, especially when considering the thermal grease and heat sink attached to the power semiconductor devices. In this paper, the frequency-domain approach is applied to the modelling of thermal dynamics for power devices. The limits of the existing RC lump...

  13. Higher order statistical frequency domain decomposition for operational modal analysis

    Science.gov (United States)

    Nita, G. M.; Mahgoub, M. A.; Sharyatpanahi, S. G.; Cretu, N. C.; El-Fouly, T. M.

    2017-02-01

    Experimental methods based on modal analysis under ambient vibrational excitation are often employed to detect structural damages of mechanical systems. Many of such frequency domain methods, such as Basic Frequency Domain (BFD), Frequency Domain Decomposition (FFD), or Enhanced Frequency Domain Decomposition (EFFD), use as first step a Fast Fourier Transform (FFT) estimate of the power spectral density (PSD) associated with the response of the system. In this study it is shown that higher order statistical estimators such as Spectral Kurtosis (SK) and Sample to Model Ratio (SMR) may be successfully employed not only to more reliably discriminate the response of the system against the ambient noise fluctuations, but also to better identify and separate contributions from closely spaced individual modes. It is shown that a SMR-based Maximum Likelihood curve fitting algorithm may improve the accuracy of the spectral shape and location of the individual modes and, when combined with the SK analysis, it provides efficient means to categorize such individual spectral components according to their temporal dynamics as coherent or incoherent system responses to unknown ambient excitations.

  14. Automated Frequency Domain Decomposition for Operational Modal Analysis

    DEFF Research Database (Denmark)

    Brincker, Rune; Andersen, Palle; Jacobsen, Niels-Jørgen

    2007-01-01

    The Frequency Domain Decomposition (FDD) technique is known as one of the most user friendly and powerful techniques for operational modal analysis of structures. However, the classical implementation of the technique requires some user interaction. The present paper describes an algorithm for au...

  15. Cavity-enhanced optical frequency combspectroscopy

    DEFF Research Database (Denmark)

    Balslev-Clausen, David Morten; Thorpe, M. J.; Kirchner, M. S.;

    2008-01-01

    Broad-bandwidth, high-spectral-resolution optical detection of human breath has identified multiple important biomarkers correlated with specific diseases and metabolic processes. This optical-frequency-comb-based breath analysis system comes with excellent performance in all criteria: high detec...... and unique molecular fingerprints exist for many biomarkers. We present a series of breath measurements including stable isotope ratios of CO2, breath concentrations of CO, and the presence of trace concentrations of NH3 in high concentrations of H2O. Udgivelsesdato: 02.05...

  16. Broadband Beamspace DOA Estimation: Frequency-Domain and Time-Domain Processing Approaches

    Directory of Open Access Journals (Sweden)

    Yan Shefeng

    2007-01-01

    Full Text Available Frequency-domain and time-domain processing approaches to direction-of-arrival (DOA estimation for multiple broadband far field signals using beamspace preprocessing structures are proposed. The technique is based on constant mainlobe response beamforming. A set of frequency-domain and time-domain beamformers with constant (frequency independent mainlobe response and controlled sidelobes is designed to cover the spatial sector of interest using optimal array pattern synthesis technique and optimal FIR filters design technique. These techniques lead the resulting beampatterns higher mainlobe approximation accuracy and yet lower sidelobes. For the scenario of strong out-of-sector interfering sources, our approaches can form nulls or notches in the direction of them and yet guarantee that the mainlobe response of the beamformers is constant over the design band. Numerical results show that the proposed time-domain processing DOA estimator has comparable performance with the proposed frequency-domain processing method, and that both of them are able to resolve correlated source signals and provide better resolution at lower signal-to-noise ratio (SNR and lower root-mean-square error (RMSE of the DOA estimate compared with the existing method. Our beamspace DOA estimators maintain good DOA estimation and spatial resolution capability in the scenario of strong out-of-sector interfering sources.

  17. Hybrid time/frequency domain modeling of nonlinear components

    DEFF Research Database (Denmark)

    Wiechowski, Wojciech Tomasz; Lykkegaard, Jan; Bak, Claus Leth

    2007-01-01

    model is used as a basis for its implementation. First, the linear network part is replaced with an ideal voltage source and a time domain (EMT) simulation is performed. During the initial oscillations, harmonic content of the converter currents is calculated at every period by a fast Fourier transform...... and the periodic steady state is identified. Obtained harmonic currents are assigned to current sources and used in the frequency domain calculation in the linear network. The obtained three-phase bus voltage is then inverse Fourier transformed and assigned to the voltage source and the time domain simulation...... is performed again. This process is repeated until the change in the magnitudes and phase angles of the fundamental and low order characteristic harmonics of the bus voltage is smaller then predefined precision indexes. The method is verified against precise time domain simulation. The convergence properties...

  18. Higher-order modulations of fs laser pulses for GHz frequency domain photon migration system.

    Science.gov (United States)

    Lin, Huang-Yi; Cheng, Nanyu; Tseng, Sheng-Hao; Chan, Ming-Che

    2014-02-24

    Except the fundamental modulation frequency, by higher-order-harmonic modulations of mode-locked laser pulses and a simple frequency demodulation circuit, a novel approach to GHz frequency-domain-photon-migration (FDPM) system was reported. With this novel approach, a wide-band modulation frequency comb is available without any external modulation devices and the only electronics to extract the optical attenuation and phase properties at a selected modulation frequency in FDPM systems are good mixers and lock-in devices. This approach greatly expands the frequency range that could be achieved by conventional FDPM systems and suggests that our system could extract much more information from biological tissues than the conventional FDPM systems. Moreover, this demonstration will be beneficial for discerning the minute change of tissue properties.

  19. A Frequency Domain Method for the Generation of Partially Coherent Normal Stationary Time Domain Signals

    Directory of Open Access Journals (Sweden)

    David O. Smallwood

    1993-01-01

    , that relates pairs of elements of the vector random process {X(t},−∞frequency response functions, and [S(f] is a diagonal matrix of real functions that can vary with frequency. The factors of the spectral density matrix, [U(f] and [S(f], are then used to generate a frame of random data in the frequency domain. The data is transformed into the time domain using an inverse FFT to generate a frame of data in the time domain. Successive frames of data are then windowed, overlapped, and added to form a vector of normal stationary sampled time histories, {X(t}, of arbitrary length.

  20. Optical-frequency-comb based ultrasound sensor

    Science.gov (United States)

    Minamikawa, Takeo; Ogura, Takashi; Masuoka, Takashi; Hase, Eiji; Nakajima, Yoshiaki; Yamaoka, Yoshihisa; Minoshima, Kaoru; Yasui, Takeshi

    2017-03-01

    Photo-acoustic imaging is a promising modality for deep tissue imaging with high spatial resolution in the field of biology and medicine. High penetration depth and spatial resolution of the photo-acoustic imaging is achieved by means of the advantages of optical and ultrasound imaging, i.e. tightly focused beam confines ultrasound-generated region within micrometer scale and the ultrasound can propagate through tissues without significant energy loss. To enhance the detection sensitivity and penetration depth of the photo-acoustic imaging, highly sensitive ultrasound detector is greatly desired. In this study, we proposed a novel ultrasound detector employing optical frequency comb (OFC) cavity. Ultrasound generated by the excitation of tightly focused laser beam onto a sample was sensed with a part of an OFC cavity, being encoded into OFC. The spectrally encoded OFC was converted to radio-frequency by the frequency link nature of OFC. The ultrasound-encoded radio-frequency can therefore be directly measured with a high-speed photodetector. We constructed an OFC cavity for ultrasound sensing with a ring-cavity erbium-doped fiber laser. We provided a proof-of-principle demonstration of the detection of ultrasound that was generated by a transducer operating at 10 MHz. Our proposed approach will serve as a unique and powerful tool for detecting ultrasounds for photo-acoustic imaging in the future.

  1. Frequency-domain photoacoustic phased array probe for biomedical imaging applications.

    Science.gov (United States)

    Telenkov, Sergey; Alwi, Rudolf; Mandelis, Andreas; Worthington, Arthur

    2011-12-01

    We report the development of a frequency-domain biomedical photoacoustic imaging system that utilizes a continuous-wave laser source with a custom intensity modulation pattern, ultrasonic phased array for signal detection, and processing coupled with a beam-forming algorithm for reconstruction of photoacoustic correlation images. Sensitivity to optical contrast was demonstrated using tissue-mimicking phantoms and in-vivo tissue samples.

  2. Distributed fiber strain and vibration sensor based on Brillouin optical time-domain reflectometry and polarization optical time-domain reflectometry.

    Science.gov (United States)

    Wang, Feng; Zhang, Xuping; Wang, Xiangchuan; Chen, Haisheng

    2013-07-15

    A distributed fiber strain and vibration sensor which effectively combines Brillouin optical time-domain reflectometry and polarization optical time-domain reflectometry is proposed. Two reference beams with orthogonal polarization states are, respectively, used to perform the measurement. By using the signal obtained from either reference beam, the vibration of fiber can be measured from the polarization effect. After combining the signals obtained by both reference beams, the strain can be measured from the Brillouin effect. In the experiment, 10 m spatial resolution, 0.6 kHz frequency measurement range, 2.5 Hz frequency resolution, and 0.2 MHz uncertainty of Brillouin frequency measurement are realized for a 4 km sensing distance.

  3. Frequency-domain waveform inversion using the phase derivative

    KAUST Repository

    Choi, Yun Seok

    2013-09-26

    Phase wrapping in the frequency domain or cycle skipping in the time domain is the major cause of the local minima problem in the waveform inversion when the starting model is far from the true model. Since the phase derivative does not suffer from the wrapping effect, its inversion has the potential of providing a robust and reliable inversion result. We propose a new waveform inversion algorithm using the phase derivative in the frequency domain along with the exponential damping term to attenuate reflections. We estimate the phase derivative, or what we refer to as the instantaneous traveltime, by taking the derivative of the Fourier-transformed wavefield with respect to the angular frequency, dividing it by the wavefield itself and taking the imaginary part. The objective function is constructed using the phase derivative and the gradient of the objective function is computed using the back-propagation algorithm. Numerical examples show that our inversion algorithm with a strong damping generates a tomographic result even for a high ‘single’ frequency, which can be a good initial model for full waveform inversion and migration.

  4. A mixed finite element domain decomposition method for nearly elastic wave equations in the frequency domain

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Xiaobing [Univ. of Tennessee, Knoxville, TN (United States)

    1996-12-31

    A non-overlapping domain decomposition iterative method is proposed and analyzed for mixed finite element methods for a sequence of noncoercive elliptic systems with radiation boundary conditions. These differential systems describe the motion of a nearly elastic solid in the frequency domain. The convergence of the iterative procedure is demonstrated and the rate of convergence is derived for the case when the domain is decomposed into subdomains in which each subdomain consists of an individual element associated with the mixed finite elements. The hybridization of mixed finite element methods plays a important role in the construction of the discrete procedure.

  5. Statistical multiresolution analysis in amplitude-frequency domain

    Institute of Scientific and Technical Information of China (English)

    SUN Hong; GUAN Bao; Henri Maitre

    2004-01-01

    A concept of statistical multiresolution analysis in amplitude-frequency domain is proposed, which is to employ the wavelet transform on the statistical character of a signal in amplitude domain. In terms of the theorem of generalized ergodicity, an algorithm to estimate the transform coefficients based on the amplitude statistical multiresolution analysis (AMA) is presented. The principle of applying the AMA to Synthetic Aperture Radar (SAR) image processing is described, and the good experimental results imply that the AMA is an efficient tool for processing of speckled signals modeled by the multiplicative noise.

  6. Small signal frequency domain model of an HVDC converter

    Energy Technology Data Exchange (ETDEWEB)

    Osauskas, C.M.; Hume, D.J.; Wood, A.R. [UnIversity of Canterbury, Christchurch (New Zealand). Dept. of Electrical and Electronic Engineering

    2001-11-01

    A small-signal analytic frequency domain model of a 6-pulse HVDC converter is presented. The model consists of a set of explicit algebraic equations which relate the transfer of distortion from AC voltage, DC current and firing angle modulation, to AC current and DC voltage. The equations represent the linearisation of the transfers around a base operating point, and are derived from a piecewise linear description of the AC current and DC voltage waveforms. The model provides an understanding of the transfer of distortion by the converter and is in excellent agreement with time domain simulations. (author)

  7. Time-domain model of quantum-dot semiconductor optical amplifiers for wideband optical signals.

    Science.gov (United States)

    Puris, D; Schmidt-Langhorst, C; Lüdge, K; Majer, N; Schöll, E; Petermann, K

    2012-11-19

    We present a novel theoretical time-domain model for a quantum dot semiconductor optical amplifier, that allows to simulate subpicosecond pulse propagation including power-based and phase-based effects. Static results including amplified spontaneous emission spectra, continuous wave amplification, and four-wave mixing experiments in addition to dynamic pump-probe simulations are presented for different injection currents. The model uses digital filters to describe the frequency dependent gain and microscopically calculated carrier-carrier scattering rates for the interband carrier dynamics. It can be used to calculate the propagation of multiple signals with different wavelengths or one wideband signal with high bitrate.

  8. Parameter Identification of Weakly Nonlinear Vibration System in Frequency Domain

    Directory of Open Access Journals (Sweden)

    Jiehua Peng

    2004-01-01

    Full Text Available A new method of identifying parameters of nonlinearly vibrating system in frequency domain is presented in this paper. The problems of parameter identification of the nonlinear dynamic system with nonlinear elastic force or nonlinear damping force are discussed. In the method, the mathematic model of parameter identification is frequency response function. Firstly, by means of perturbation method the frequency response function of weakly nonlinear vibration system is derived. Next, a parameter transformation is made and the frequency response function becomes a linear function of the new parameters. Then, based on this function and with the least square method, physical parameters of the system are identified. Finally, the applicability of the proposed technique is confirmed by numerical simulation.

  9. The Peltier driven frequency domain approach in thermal analysis.

    Science.gov (United States)

    De Marchi, Andrea; Giaretto, Valter

    2014-10-01

    The merits of Frequency Domain analysis as a tool for thermal system characterization are discussed, and the complex thermal impedance approach is illustrated. Pure AC thermal flux generation with negligible DC component is possible with a Peltier device, differently from other existing methods in which a significant DC component is intrinsically attached to the generated AC flux. Such technique is named here Peltier Driven Frequency Domain (PDFD). As a necessary prerequisite, a novel one-dimensional analytical model for an asymmetrically loaded Peltier device is developed, which is general enough to be useful in most practical situations as a design tool for measurement systems and as a key for the interpretation of experimental results. Impedance analysis is possible with Peltier devices by the inbuilt Seebeck effect differential thermometer, and is used in the paper for an experimental validation of the analytical model. Suggestions are then given for possible applications of PDFD, including the determination of thermal properties of materials.

  10. The Peltier driven frequency domain approach in thermal analysis

    Science.gov (United States)

    Marchi, Andrea De; Giaretto, Valter

    2014-10-01

    The merits of Frequency Domain analysis as a tool for thermal system characterization are discussed, and the complex thermal impedance approach is illustrated. Pure AC thermal flux generation with negligible DC component is possible with a Peltier device, differently from other existing methods in which a significant DC component is intrinsically attached to the generated AC flux. Such technique is named here Peltier Driven Frequency Domain (PDFD). As a necessary prerequisite, a novel one-dimensional analytical model for an asymmetrically loaded Peltier device is developed, which is general enough to be useful in most practical situations as a design tool for measurement systems and as a key for the interpretation of experimental results. Impedance analysis is possible with Peltier devices by the inbuilt Seebeck effect differential thermometer, and is used in the paper for an experimental validation of the analytical model. Suggestions are then given for possible applications of PDFD, including the determination of thermal properties of materials.

  11. Speaker Identification using Frequency Dsitribution in the Transform Domain

    Directory of Open Access Journals (Sweden)

    Dr. H B Kekre

    2012-02-01

    Full Text Available In this paper, we propose Speaker Identification using the frequency distribution of various transforms like DFT (Discrete Fourier Transform, DCT (Discrete Cosine Transform, DST (Discrete Sine Transform, Hartley, Walsh, Haar and Kekre transforms. The speech signal spoken by a particular speaker is converted into frequency domain by applying the different transform techniques. The distribution in the transform domain is utilized to extract the feature vectors in the training and the matching phases. The results obtained by using all the seven transform techniques have been analyzed and compared. It can be seen that DFT, DCT, DST and Hartley transform give comparatively similar results (Above 96%. The results obtained by using Haar and Kekre transform are very poor. The best results are obtained by using DFT (97.19% for a feature vector of size 40.

  12. Structural eigenfrequency optimization based on local sub-domain "frequencies"

    DEFF Research Database (Denmark)

    Pedersen, Pauli; Pedersen, Niels Leergaard

    2013-01-01

    The engineering approach of fully stressed design is a practical tool with a theoretical foundation. The analog approach to structural eigenfrequency optimization is presented here with its theoretical foundation. A numerical redesign procedure is proposed and illustrated with examples.......For the ideal case, an optimality criterion is fulfilled if the design have the same sub-domain ”frequency” (local Rayleigh quotient). Sensitivity analysis shows an important relation between squared system eigenfrequency and squared local sub-domain frequency for a given eigenmode. Higher order...... eigenfrequencies may also be controlled in this manner.The presented examples are based on 2D finite element models with the use of subspace iteration for analysis and a recursive design procedure based on the derived optimality condition. The design that maximize a frequency depend on the total amount...

  13. Research on the frequency domain ∑△-DPCA

    Institute of Scientific and Technical Information of China (English)

    Shen Mingwei; Zhu Daiyin; Zhu Zhaoda

    2008-01-01

    The frequency domain ∑△-DPCA processing (F-∑△-DPCA) is investigated in detail, and an im-proved scheme for the F-]EA-DPCA is proposed, which can significantly reduce the computational burden. In practice, because of the sum and difference beam pattern designed independently and other system errors, the clutter suppression of the time domain ∑△-DPCA processing (T-∑△-DPCA) is significantly degraded. However,the F-∑△-DPCA adaptively calculates the optimum gain ratio for motion compensation within each Doppler cell,which is robust to system errors. Theoretical analysis and simulation results are presented to validate that the F-∑△-DPCA can achieve superior performance of clutter cancellation than the time domain processing, and its performance can be significantly increased if more pulses are used for the Doppler filtering. The improved approach is efficient, and feasible for real-time application.

  14. Frequency domain analysis of noise in autoregulated gene circuits

    OpenAIRE

    Simpson, Michael L.; Cox, Chris D.; Sayler, Gary S.

    2003-01-01

    We describe a frequency domain technique for the analysis of intrinsic noise within negatively autoregulated gene circuits. This approach is based on the transfer function around the feedback loop (loop transmission) and the equivalent noise bandwidth of the system. The loop transmission, T, is shown to be a determining factor of the dynamics and the noise behavior of autoregulated gene circuits, and this T-based technique provides a simple and flexible method for the analysis of noise arisin...

  15. Reduced Order Internal Models in the Frequency Domain

    OpenAIRE

    Laakkonen, Petteri; Paunonen, Lassi

    2016-01-01

    The internal model principle states that all robustly regulating controllers must contain a suitably reduplicated internal model of the signal to be regulated. Using frequency domain methods, we show that the number of the copies may be reduced if the class of perturbations in the problem is restricted. We present a two step design procedure for a simple controller containing a reduced order internal model achieving robust regulation. The results are illustrated with an example of a five tank...

  16. Frequency domain stability criteria for fractional-order control systems

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    This paper concerns about the frequency domain stability criteria for fractional-order control systems. On the base of characteristics of the fractional-order equations solutions, we consider the Nyquist stability criterion in a wider sense and obtain a more common means to analyze the stability of fractional-order systems conveniently. Finally, this paper illustrates the generalized stability criteria with an example to show the effect of the parameters variation on the fractional-order control systems.

  17. An implementation of synthetic aperture focusing technique in frequency domain.

    Science.gov (United States)

    Stepinski, Tadeusz

    2007-07-01

    A new implementation of a synthetic aperture focusing technique (SAFT) based on concepts used in synthetic aperture radar and sonar is presented in the paper. The algorithm, based on the convolution model of the imaging system developed in frequency domain, accounts for the beam pattern of the finite-sized transducer used in the synthetic aperture. The 2D fast Fourier transform (FFT) is used for the calculation of a 2D spectrum of the ultrasonic data. The spectrum is then interpolated to convert the polar coordinate system used for the acquisition of ultrasonic signals to the rectangular coordinates used for the presentation of imaging results. After compensating the transducer lobe amplitude profile using a Wiener filter, the transformed spectrum is subjected to the 2D inverse Fourier transform to get the time-domain image again. The algorithm is computationally attractive due to the use of 2D FFT. The performance of the proposed frequency-domain algorithm and the classical time-domain SAFT are compared in the paper using simulated and real ultrasonic data.

  18. Frequency-domain waveform inversion using the unwrapped phase

    KAUST Repository

    Choi, Yun Seok

    2011-01-01

    Phase wrapping in the frequency-domain (or cycle skipping in the time-domain) is the major cause of the local minima problem in the waveform inversion. The unwrapped phase has the potential to provide us with a robust and reliable waveform inversion, with reduced local minima. We propose a waveform inversion algorithm using the unwrapped phase objective function in the frequency-domain. The unwrapped phase, or what we call the instantaneous traveltime, is given by the imaginary part of dividing the derivative of the wavefield with respect to the angular frequency by the wavefield itself. As a result, the objective function is given a traveltime-like function, which allows us to smooth it and reduce its nonlinearity. The gradient of the objective function is computed using the back-propagation algorithm based on the adjoint-state technique. We apply both our waveform inversion algorithm using the unwrapped phase and the conventional waveform inversion and show that our inversion algorithm gives better convergence to the true model than the conventional waveform inversion. © 2011 Society of Exploration Geophysicists.

  19. Tunable optical frequency division using a phase-locked optical parametric oscillator.

    Science.gov (United States)

    Lee, D; Wong, N C

    1992-01-01

    We report the experimental demonstration of a novel optical parametric oscillator approach to tunable optical frequency division. The beat frequency of the signal and idler subharmonic outputs of a tunable cw KTP optical parametric oscillator was phase locked to a microwave reference frequency source, which thus permitted precise determination of the output frequencies at approximately half the input pump frequency.

  20. New multiplexing scheme for monitoring fiber optic Bragg grating sensors in the coherence domain

    OpenAIRE

    Dakin, J.P.; Ecke, W.; Rothardt, M.; Schauer, J; Usbeck, K.; Willsch, R.

    1997-01-01

    A new multiplexing scheme for monitoring fiber optic Bragg gratings in the coherence domain has been developed. Grating pairs with different grating distances are distributed along a fiber line, and interference between their reflections is monitored with a scanning Michelson interferometer. The Bragg wavelength of the individual sensor elements is determined from the interference signal frequency

  1. Time domain terahertz electro- and magneto-optic spectroscopy

    CERN Document Server

    Moore, G P

    2001-01-01

    sub i sub c sub u sub l sub a sub r = 0 centre dot 19m sub e and m sub p sub a sub r sub a sub l sub l sub e sub l = 0 centre dot 90m sub e. The temperature dependence of the cyclotron resonance was measured over the range 5K to 80 K, and a peak is found at approx 30 K which can be explained in terms of ionised and neutral impurity scattering at temperatures below 30 K and by phonon scattering above 30 K. The measurement of small amplitude ferromagnetic resonance oscillations in the time domain in thin films of permalloy (78), iron and cobalt has been achieved by using the time resolved magneto-optic Kerr effect. A stripline device was fabricated to provide an out of plane broadband magnetic pulse with a peak strength of approx 5 Oe. The observed frequencies are shown to agree well with the established theory. A time domain terahertz spectrometer and a bolometer have been used to study the coherent THz radiation emitted from n- and p-type InAs surfaces illuminated by femtosecond near infrared pulses. The magn...

  2. A pseudospectral collocation time-domain method for diffractive optics

    DEFF Research Database (Denmark)

    Dinesen, P.G.; Hesthaven, J.S.; Lynov, Jens-Peter

    2000-01-01

    We present a pseudospectral method for the analysis of diffractive optical elements. The method computes a direct time-domain solution of Maxwell's equations and is applied to solving wave propagation in 2D diffractive optical elements. (C) 2000 IMACS. Published by Elsevier Science B.V. All rights...

  3. Quantitative analysis of a frequency-domain nonlinearity indicator.

    Science.gov (United States)

    Reichman, Brent O; Gee, Kent L; Neilsen, Tracianne B; Miller, Kyle G

    2016-05-01

    In this paper, quantitative understanding of a frequency-domain nonlinearity indicator is developed. The indicator is derived from an ensemble-averaged, frequency-domain version of the generalized Burgers equation, which can be rearranged in order to directly compare the effects of nonlinearity, absorption, and geometric spreading on the pressure spectrum level with frequency and distance. The nonlinear effect is calculated using pressure-squared-pressure quadspectrum. Further theoretical development has given an expression for the role of the normalized quadspectrum, referred to as Q/S by Morfey and Howell [AIAA J. 19, 986-992 (1981)], in the spatial rate of change of the pressure spectrum level. To explore this finding, an investigation of the change in level for initial sinusoids propagating as plane waves through inviscid and thermoviscous media has been conducted. The decibel change with distance, calculated through Q/S, captures the growth and decay of the harmonics and indicates that the most significant changes in level occur prior to sawtooth formation. At large distances, the inviscid case results in a spatial rate of change that is uniform across all harmonics. For thermoviscous media, large positive nonlinear gains are observed but offset by absorption, which leads to a greater overall negative spatial rate of change for higher harmonics.

  4. Quantifying online visuomotor feedback utilization in the frequency domain.

    Science.gov (United States)

    de Grosbois, John; Tremblay, Luc

    2016-12-01

    The utilization of sensory information during activities of daily living is ubiquitous both prior to and during movements (i.e., related to planning and online control, respectively). Because of the overlapping nature of online corrective processes, the quantification of feedback utilization has proven difficult. In the present study, we primarily sought to evaluate the utility of a novel analysis in the frequency domain for identifying visuomotor feedback utilization (i.e., online control). A second goal was to compare the sensitivity of the frequency analysis to that of currently utilized measures of online control. Participants completed reaching movements to targets located 27, 30, and 33 cm from a start position. During these reaches, vision of the environment was either provided or withheld. Performance was assessed across contemporary measures of online control. For the novel frequency analysis presented in this study, the acceleration profiles of reaching movements were detrended with a 5th-order polynomial fit, and the proportional power spectra were computed from the residuals of these fits. The results indicated that the use of visual feedback during reaching movements increased the contribution of the 4.68-Hz frequency to the residuals of the acceleration profiles. Comparisons across all measures of online control showed that the most sensitive measure was the squared Fisher transform of the correlation between the positions at 75 % and 100 % of the movement time. However, because such correlational measures can be contaminated by offline control processes, the frequency-domain analysis proposed herein represents a viable and promising alternative to detect changes in online feedback utilization.

  5. Frequency domain probe design for high frequency sensing of soil moisture

    Science.gov (United States)

    Accurate moisture sensing is an important need for many research programs as well as in control of industrial processes. This paper covers the development of a frequency domain sensing probe for use in obtaining measurements of material properties suitable for work ranging from 0 to 6GHz. The probe ...

  6. Frequency Domain Modelling of Electromagnetic Wave Propagation in Layered Media

    Science.gov (United States)

    Schmidt, Felix; Lünenschloss, Peter; Mai, Juliane; Wagner, Norman; Töpfer, Hannes; Bumberger, Jan

    2016-04-01

    The amount of water in porous media such as soils and rocks is a key parameter when water resources are under investigation. Especially the quantitative spatial distribution and temporal evolution of water contents in soil formations are needed. In high frequency electromagnetic applications soil water content is quantitatively derived from the propagation behavior of electromagnetic waves along waveguides embedded in soil formations. The spatial distribution of the dielectric material properties along the waveguide can be estimated by numerical solving of the inverse problem based on the full wave forward model in time or frequency domain. However, current approaches mostly neglect or approximate the frequency dependence of the electromagnetic material properties of transfer function of the waveguide. As a first prove of concept a full two port broadband frequency domain forward model for propagation of transverse electromagnetic (TEM) waves in coaxial waveguide has been implemented. It is based on the propagation matrix approach for layered transmission line sections. Depending on the complexity of the material different models for the frequency dependent complex permittivity were applied. For the validation of the model a broadband frequency domain measurement with network analyzer technique was used. The measurement is based on a 20 cm long 50 Ohm 20/46 coaxial transmission line cell considering inhomogeneous material distributions. This approach allows (i) an increase of the waveguide calibration accuracy in comparison to conventional TDR based technique and (ii) the consideration of the broadband permittivity spectrum of the porous material. In order to systematic analyze the model, theoretical results were compared with measurements as well as 3D broadband finite element modeling of homogeneous and layered media in the coaxial transmission line cell. Defined standards (Teflon, dry glass beads, de-ionized water) were placed inside the line as the dielectric

  7. A frequency domain approach to handling qualities design

    Science.gov (United States)

    Wolovich, W. A.

    1978-01-01

    A method for designing linear multivariable feedback control systems based on desired closed loop transfer matrix information is introduced. The technique which was employed to achieve the final design was based on a theoretical result, known as the structure theorem. The structure theorem was a frequency domain relationship which simplified the expression for the transfer matrix (matrix of transfer functions) of a linear time-invariant multivariable system. The effect of linear state variable feedback on the closed loop transfer matrix of the system was also clarified.

  8. Baseband feedback for SAFARI-SPICA using Frequency Domain Multiplexing

    Science.gov (United States)

    Bounab, A.; de Korte, P.; Cros, A.; van der Kuur, J.; van Leeuwen, B. J.; Monna, B.; Mossel, R.; Nieuwenhuizen, A.; Ravera, L.

    We report on the performance of the digital baseband feedback circuit developed to readout and process signals from arrays of transition edge sensors for SPICA-SAFARI in frequency domain multiplexing (FDM). The standard procedure to readout the SQUID current amplifiers is to use a feedback loop (flux-locked loop: FLL). However the achievable FFL bandwidth is limited by the cable transport delay t_d, which makes standard feedback inconvenient. A much better approach is to use baseband feedback. We have developed a model of the electronic readout chain for SPICA-SAFARI instrument by using an Anlog-digital co-simulation based on Simulink-System Generator environment.

  9. A frequency-domain derivation of shot-noise

    Science.gov (United States)

    Rice, Frank

    2016-01-01

    A formula for shot-noise is derived in the frequency-domain. The derivation is complete and reasonably rigorous while being appropriate for undergraduate students; it models a sequence of random pulses using Fourier sine and cosine series, and requires some basic statistical concepts. The text here may serve as a pedagogic introduction to the spectral analysis of random processes and may prove useful to introduce students to the logic behind stochastic problems. The concepts of noise power spectral density and equivalent noise bandwidth are introduced.

  10. Numerical methods for time-domain and frequency-domain analysis: applications in engineering

    Science.gov (United States)

    Tamas, R. D.

    2015-11-01

    Numerical methods are widely used for modeling different physical phenomena in engineering, especially when an analytic approach is not possible. Time-domain or frequency- domain type variations are generally investigated, depending on the nature of the process under consideration. Some methods originate from mechanics, although most of their applications belong to other fields, such as electromagnetism. Conversely, other methods were firstly developed for electromagnetism, but their field of application was extended to other fields. This paper presents some results that we have obtained by using a general purpose method for solving linear equations, i.e., the method of moments (MoM), and a time-domain method derived for electromagnetism, i.e., the Transmission Line Matrix method (TLM).

  11. A review of time-domain and frequency-domain component mode synthesis method

    Science.gov (United States)

    Craig, R. R., Jr.

    1985-01-01

    Hurty (1965) has conducted a dynamic analysis of structural systems using component modes. The component mode synthesis (CMS) procedure considered by him represents a form of substructure coupling analysis which is often utilized in structural dynamics. Time-domain CMS methods employing real modes are discussed, taking into account real component modes, normal modes, redundant constraint modes, rigid-body modes, attachment modes, inertia-relief modes, statically-complete interface mode sets, dynamic component mode supersets, component modal models, the coupling of components, and the classification of methods. Attention is also given to the experimental determination of component mode synthesis parameters, time-domain CMS methods for damped systems, and frequency-domain CMS methods for damped systems.

  12. High-Performance Computational Electromagnetics in Frequency-Domain and Time-Domain

    Science.gov (United States)

    2015-03-04

    aforementioned contributions, for a given 1In view of its applications to seismic wave propagation Dr. Amlani’s PhD thesis received two awards at Cal- tech, one...for wave scattering problems. PhD thesis, California Institute of Technol- ogy, 2014. Available at http://www.its.caltech.edu/~obruno/preprints...solutions for some of the most challenging scattering problems in science and engineering. Electromagnetic scattering . Frequency domain solvers. Integral

  13. Causality between regional stock markets: A frequency domain approach

    Directory of Open Access Journals (Sweden)

    Gradojević Nikola

    2013-01-01

    Full Text Available Using a data set from five regional stock exchanges (Serbia, Croatia, Slovenia, Hungary and Germany, this paper presents a frequency domain analysis of a causal relationship between the returns on the CROBEX, SBITOP, CETOP and DAX indices, and the return on the major Serbian stock exchange index, BELEX 15. We find evidence of a somewhat dominant effect of the CROBEX and CETOP stock indices on the BELEX 15 stock index across a range of frequencies. The results also indicate that the BELEX 15 index and the SBITOP index interact in a bi-directional causal fashion. Finally, the DAX index movements consistently drive the BELEX 15 index returns for cycle lengths between 3 and 11 days without any feedback effect.

  14. Frequency Domain Storage Ring Method for Electric Dipole Moment Measurement

    CERN Document Server

    Talman, Richard

    2015-01-01

    Precise measurement of the electric dipole moments (EDM) of fundamental charged particles would provide a significant probe of physics beyond the standard model. Any measurably large EDM would imply violation of both time reversal and parity conservation, with implications for the matter/anti-matter imbalance of the universe, not currently understood within the standard model. A frequency domain (i.e. difference of frequencies) method is proposed for measuring the EDM of electrons or protons or, with modifications, deuterons. Anticipated precision (i.e. reproducibility) is $10^{-30}\\,$e-cm for the proton EDM, with comparable accuracy (i.e. including systematic error). This would be almost six orders of magnitude smaller than the present upper limit, and will provide a stringent test of the standard model. Resonant polarimetry, made practical by the large polarized beam charge, is the key (most novel, least proven) element of the method. Along with the phase-locked, rolling polarization "Koop spin wheel," reso...

  15. Steering optical comb frequency by rotating polarization state

    CERN Document Server

    Zhang, Y; Zhang, X F; Zhang, L; Han, W; Guo, W; Jiang, H; Zhang, S

    2016-01-01

    Optical frequency combs, with precise control of repetition rate and carrier-envelope-offset frequency, have revolutionized many fields, such as fine optical spectroscopy, optical frequency standards, ultra-fast science research, ultra-stable microwave generation and precise ranging measurement. However, existing high bandwidth frequency control methods have small dynamic range, requiring complex hybrid control techniques. To overcome this limitation, we develop a new approach, where a home-made intra-cavity electro-optic modulator tunes polarization state of laser signal rather than only optical length of the cavity, to steer frequencies of a nonlinear-polarization-rotation mode-locked laser. By taking advantage of birefringence of the whole cavity, this approach results in not only broadband but also relative large-dynamic frequency control. Experimental results show that frequency control dynamic range increase at least one order in comparison with the traditional intra-cavity electro-optic modulator techn...

  16. Integrated optical sensors for the chemical domain

    NARCIS (Netherlands)

    Lambeck, Paul V.

    2006-01-01

    During the last decade there has been a rapidly growing interest in integrated optical (IO) sensors, expecially because many of them principally allow for sensitive, real time, label-free-on-site measurements of the concentration of (bio-)chemical species. This review aims at giving an overview of t

  17. Integrated optical sensors for the chemical domain

    NARCIS (Netherlands)

    Lambeck, Paul

    2006-01-01

    During the last decade there has been a rapidly growing interest in integrated optical (IO) sensors, expecially because many of them principally allow for sensitive, real time, label-free-on-site measurements of the concentration of (bio-)chemical species. This review aims at giving an overview of t

  18. Damping identification in frequency domain using integral method

    Science.gov (United States)

    Guo, Zhiwei; Sheng, Meiping; Ma, Jiangang; Zhang, Wulin

    2015-03-01

    A new method for damping identification of linear system in frequency domain is presented, by using frequency response function (FRF) with integral method. The FRF curve is firstly transformed to other type of frequency-related curve by changing the representations of horizontal and vertical axes. For the newly constructed frequency-related curve, integral is conducted and the area forming from the new curve is used to determine the damping. Three different methods based on integral are proposed in this paper, which are called FDI-1, FDI-2 and FDI-3 method, respectively. For a single degree of freedom (Sdof) system, the formulated relation of each method between integrated area and loss factor is derived theoretically. The numeral simulation and experiment results show that, the proposed integral methods have high precision, strong noise resistance and are very stable in repeated measurements. Among the three integral methods, FDI-3 method is the most recommended because of its higher accuracy and simpler algorithm. The new methods are limited to linear system in which modes are well separated, and for closely spaced mode system, mode decomposition process should be conducted firstly.

  19. Infrared optical activity: electric field approaches in time domain.

    Science.gov (United States)

    Rhee, Hanju; Choi, Jun-Ho; Cho, Minhaeng

    2010-12-21

    Vibrational circular dichroism (VCD) spectroscopy provides detailed information about the absolute configurations of chiral molecules including biomolecules and synthetic drugs. This method is the infrared (IR) analogue of the more popular electronic CD spectroscopy that uses the ultraviolet and visible ranges of the electromagnetic spectrum. Because conventional electronic CD spectroscopy measures the difference in signal intensity, problems such as weak signal and low time-resolution can limit its utility. To overcome the difficulties associated with that approach, we have recently developed femtosecond IR optical activity (IOA) spectrometry, which directly measures the IOA free-induction-decay (FID), the impulsive chiroptical IR response that occurs over time. In this Account, we review the time-domain electric field measurement and calculation methods used to simultaneously characterize VCD and related vibrational optical rotatory dispersion (VORD) spectra. Although conventional methods measure the electric field intensity, this vibrational technique is based on a direct phase-and-amplitude measurement of the electric field of the chiroptical signal over time. This method uses a cross-polarization analyzer to carry out heterodyned spectral interferometry. The cross-polarization scheme enables us to selectively remove the achiral background signal, which is the dominant noise component present in differential intensity measurement techniques. Because we can detect the IOA FID signal in a phase-amplitude-sensitive manner, we can directly characterize the time-dependent electric dipole/magnetic dipole response function and the complex chiral susceptibility that contain information about the angular oscillations of charged particles. These parameters yield information about the VCD and VORD spectra. In parallel with such experimental developments, we have also calculated the IOA FID signal and the resulting VCD spectrum. These simulations use a quantum mechanical

  20. Building the analytical response in frequency domain of AC biased bolometers - Application to Planck/HFI

    Science.gov (United States)

    Sauvé, Alexandre; Montier, Ludovic

    2016-10-01

    uc(Context): Bolometers are high sensitivity detector commonly used in Infrared astronomy. The HFI instrument of the Planck satellite makes extensive use of them, but after the satellite launch two electronic related problems revealed critical. First an unexpected excess response of detectors at low optical excitation frequency for ν knowledge of detector response. However bolometers have highly nonlinear characteristics, coming from their electrical and thermal coupling making them very difficult to model. uc(Goal): We present a method to build the analytical transfer function in frequency domain which describe the voltage response of an Alternative Current (AC) biased bolometer to optical excitation, based on the standard bolometer model. This model is built using the setup of the Planck/HFI instrument and offers the major improvement of being based on a physical model rather than the currently in use had-hoc model based on Direct Current (DC) bolometer theory. uc(Method): The analytical transfer function expression will be presented in matrix form. For this purpose, we build linearized versions of the bolometer electro thermal equilibrium. A custom description of signals in frequency is used to solve the problem with linear algebra. The model performances is validated using time domain simulations. uc(Results): The provided expression is suitable for calibration and data processing. It can also be used to provide constraints for fitting optical transfer function using real data from steady state electronic response and optical response. The accurate description of electronic response can also be used to improve the ADC nonlinearity correction for quickly varying optical signals.

  1. Frequency-wavenumber domain phase inversion along reflection wavepaths

    KAUST Repository

    Yu, Han

    2014-12-01

    A background velocity model containing the correct low-wavenumber information is desired for both the quality of the migration image and the success of waveform inversion. To achieve this goal, the velocity is updated along the reflection wavepaths, rather than along both the reflection ellipses and transmission wavepaths as in conventional FWI. This method allows for reconstructing the low-wavenumber part of the background velocity model, even in the absence of long offsets and low-frequency component of the data. Moreover, in gradient-based iterative updates, instead of forming the data error conventionally, we propose to exploit the phase mismatch between the observed and the calculated data. The phase mismatch emphasizes a kinematic error and varies quasi-linearly with respect to the velocity error. The phase mismatch is computed (1) in the frequency-wavenumber (f-k) domain replacing the magnitudes of the calculated common shot gather by those of the observed one, and (2) in the temporal-spatial domain to form the difference between the transformed calculated common-shot gather and the observed one. The background velocity model inverted according to the proposed methods can serve as an improved initial velocity model for conventional waveform inversion. Tests with synthetic and field data show both the benefits and limitations of this method.

  2. Optical Theory Improvements to Space Domain Awareness

    Science.gov (United States)

    2016-09-15

    observations are collected through ground-based radar and optical systems as well as space based assets . This research focuses on a ground-based...addition, his professional mentoring will be a great asset going forward in my career. Thanks to Capt Kyle Stewart for helpful discussions on implementation...visualization demonstrates how the point detection, matched filter , Binary Hypothesis Test (BHT), and MHT algorithms are related. . . . . . . . . . . . . 13 2.5

  3. Patellofemoral pain syndrome: electromyography in a frequency domain analysis

    Science.gov (United States)

    Catelli, D. S.; Kuriki, H. U.; Polito, L. F.; Azevedo, F. M.; Negrão Filho, R. F.; Alves, N.

    2011-09-01

    The Patellofemoral Pain Syndrome (PFPS), has a multifactorial etiology and affects approximately 7 to 15% of the population, mostly women, youth, adults and active persons. PFPS causes anterior or retropatelar pain that is exacerbated during functional motor gestures, such as up and down stairs or spending long periods of time sitting, squatting or kneeling. As the diagnostic evaluation of this syndrome is still indirect, different mechanisms and methodologies try to make a classification that distinguishes patients with PFPS in relation to asymptomatic. Thereby, the purpose of this investigation was to determine the characteristics of the electromyographic (EMG) signal in the frequency domain of the vastus medialis oblique (VMO) and vastus lateralis (VL) in patients with PFPS, during the ascent of stairs. 33 young women (22 control group and 11 PFPS group), were evaluated by EMG during ascent of stairs. The VMO mean power frequency (MPF) and the VL frequency 95% (F95) were lower in symptomatic individuals. This may be related to the difference in muscle recruitment strategy exerted by each muscle in the PFPS group compared to the control group.

  4. TOPOLOGY OPTIMIZATION OF TRUSS STRUCTURE WITH FUNDAMENTAL FREQUENCY AND FREQUENCY DOMAIN DYNAMIC RESPONSE CONSTRAINTS

    Institute of Scientific and Technical Information of China (English)

    Pan Jin; Wang De-yu

    2006-01-01

    In this paper, adaptive genetic algorithm (AGA) is applied to topology optimization of truss structure with frequency domain excitations. The optimization constraints include fundamental frequency, displacement responses under force excitations and acceleration responses under foundation acceleration excitations. The roulette wheel selection operator, adaptive crossover and mutation operators are used as genetic operators. Some heuristic strategies are put forward to direct the deletion of the extra bars and nodes on truss structures. Three examples demonstrate that the proposed method can yield the optimum structure form and the lightest weight of the given ground structure while satisfying dynamic response constraints.

  5. Optical Transmitter Terminal for Selective RF High Frequency Bans Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of the proposal work is to investigate the highly innovative conceptual design of an optical communication selective frequency transmitter terminal...

  6. Double random fractional Fourier domain encoding for optical security

    Science.gov (United States)

    Unnikrishnan, G.; Singh, Kehar

    2000-11-01

    We propose a new optical encryption technique using the fractional Fourier transform. In this method, the data are encrypted to a stationary white noise by two statistically independent random phase masks in fractional Fourier domains. To decrypt the data correctly, one needs to specify the fractional domains in which the input plane, encryption plane, and output planes exist, in addition to the key used for encryption. The use of an anamorphic fractional Fourier transform for the encryption of 2D data is also discussed. We suggest an optical implementation of the proposed idea. Results of a numerical simulation to analyze the performance of the proposed method are presented.

  7. On the Analysis Methods for the Time Domain and Frequency Domain Response of a Buried Objects*

    Science.gov (United States)

    Poljak, Dragan; Šesnić, Silvestar; Cvetković, Mario

    2014-05-01

    There has been a continuous interest in the analysis of ground-penetrating radar systems and related applications in civil engineering [1]. Consequently, a deeper insight of scattering phenomena occurring in a lossy half-space, as well as the development of sophisticated numerical methods based on Finite Difference Time Domain (FDTD) method, Finite Element Method (FEM), Boundary Element Method (BEM), Method of Moments (MoM) and various hybrid methods, is required, e.g. [2], [3]. The present paper deals with certain techniques for time and frequency domain analysis, respectively, of buried conducting and dielectric objects. Time domain analysis is related to the assessment of a transient response of a horizontal straight thin wire buried in a lossy half-space using a rigorous antenna theory (AT) approach. The AT approach is based on the space-time integral equation of the Pocklington type (time domain electric field integral equation for thin wires). The influence of the earth-air interface is taken into account via the simplified reflection coefficient arising from the Modified Image Theory (MIT). The obtained results for the transient current induced along the electrode due to the transmitted plane wave excitation are compared to the numerical results calculated via an approximate transmission line (TL) approach and the AT approach based on the space-frequency variant of the Pocklington integro-differential approach, respectively. It is worth noting that the space-frequency Pocklington equation is numerically solved via the Galerkin-Bubnov variant of the Indirect Boundary Element Method (GB-IBEM) and the corresponding transient response is obtained by the aid of inverse fast Fourier transform (IFFT). The results calculated by means of different approaches agree satisfactorily. Frequency domain analysis is related to the assessment of frequency domain response of dielectric sphere using the full wave model based on the set of coupled electric field integral

  8. An Improved Frequency Domain Technique for Determining Soil Water Content

    Institute of Scientific and Technical Information of China (English)

    SUN Yu-Rui; MA Dao-Kun; LIN Jian-Hui; P. SCHULZE LAMMERS; L. DAMEROW

    2005-01-01

    For many years a soil water content sensor with low cost, reliability and sufficient accuracy has been desirable. Thus,an improved measurement method based on the frequency domain (FD) principle for determining soil water content was considered. Unlike other measurement principles, a new measurable index, η, which was independent of the output impedance and the amplitude of the oscillator while relying on the electrical impedance of a multi-pin probe, was proposed. Moreover, a model for processing the impedance of the multi-pin soil probe was developed, and several important electrical parameters for establishing their operating ranges applicable to this probe were evaluated. In order to confirm the theoretical analysis, an experiment was conducted with a 4-pin probe. Using the developed model, the relationship between the proposed indexηand soil volumetric water content was shown to be linear (R2 = 0.9921). Thus, as the measurable index, ηseemed satisfactory.

  9. Frequency domain synthesis of trajectory learning controllers for robot manipulators

    Directory of Open Access Journals (Sweden)

    Tom Kavli

    1993-07-01

    Full Text Available Trajectory learning control is a method for generating near to optimal feedforward control for systems that are controlled along a reference trajectory in repeated cycles. Iterative refinements of a stored feedforward control sequence corresponding to one cycle of the control trajectory is computed based upon the recorded trajectory error from the previous cycle. Several learning operators have been proposed in earlier work, and convergence proofs are developed for certain classes of systems, but no satisfactory method for design and analysis of learning operators under the presence of uncertainties in the system model have been presented. This article presents frequency domain methods for analysing the convergence properties and performance of the learning controller when the amplitude and phase of the system transfer function is assumed to be within specified windows. Experimental results with an industrial robot manipulator confirm the theoretical results.

  10. Accurate reconstruction of digital holography using frequency domain zero padding

    Science.gov (United States)

    Shin, Jun Geun; Kim, Ju Wan; Lee, Jae Hwi; Lee, Byeong Ha

    2017-04-01

    We propose an image reconstruction method of digital holography for getting more accurate reconstruction. Digital holography provides both the light amplitude and the phase of a specimen through recording the interferogram. Since the Fresenl diffraction can be efficiently implemented by the Fourier transform, zero padding technique can be applied to obtain more accurate information. In this work, we report the method of frequency domain zero padding (FDZP). Both in computer-simulation and in experiment made with a USAF 1951 resolution chart and target, the FDZD gave the more accurate rconstruction images. Even though, the FDZD asks more processing time, with the help of graphics processing unit (GPU), it can find good applications in digital holography for 3-D profile imaging.

  11. Iterative procedures for wave propagation in the frequency domain

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seongjai [Rice Univ., Houston, TX (United States); Symes, W.W.

    1996-12-31

    A parallelizable two-grid iterative algorithm incorporating a domain decomposition (DD) method is considered for solving the Helmholtz problem. Since a numerical method requires choosing at least 6 to 8 grid points per wavelength, the coarse-grid problem itself is not an easy task for high frequency applications. We solve the coarse-grid problem using a nonoverlapping DD method. To accelerate the convergence of the iteration, an artificial damping technique and relaxation parameters are introduced. Automatic strategies for finding efficient parameters are discussed. Numerical results are presented to show the effectiveness of the method. It is numerically verified that the rate of convergence of the algorithm depends on the wave number sub-linearly and does not deteriorate as the mesh size decreases.

  12. A Frequency Domain Steganography using Z Transform (FDSZT)

    CERN Document Server

    Mandal, J K

    2012-01-01

    Image steganography is art of hiding information onto the cover image. In this proposal a transformed domain based gray scale image authentication/data hiding technique using Z transform (ZT) termed as FDSZT, has been proposed. ZTransform is applied on 2x2 masks of the source image in row major order to transform original sub image (cover image) block to its corresponding frequency domain. One bit of the hidden image is embedded in each mask of the source image onto the fourth LSB of transformed coefficient based on median value of the mask. A delicate handle has also been performed as post embedding operation for proper decoding. Stego sub image is obtained through a reverse transform as final step of embedding in a mask. During the process of embedding, dimension of the hidden image followed by the content of the message/hidden image are embedded. Reverse process is followed during decoding. High PSNR obtained for various images conform the quality of invisible watermark of FDSZT.

  13. A new image cipher in time and frequency domains

    Science.gov (United States)

    Abd El-Latif, Ahmed A.; Niu, Xiamu; Amin, Mohamed

    2012-10-01

    Recently, various encryption techniques based on chaos have been proposed. However, most existing chaotic encryption schemes still suffer from fundamental problems such as small key space, weak security function and slow performance speed. This paper introduces an efficient encryption scheme for still visual data that overcome these disadvantages. The proposed scheme is based on hybrid Linear Feedback Shift Register (LFSR) and chaotic systems in hybrid domains. The core idea is to scramble the pixel positions based on 2D chaotic systems in frequency domain. Then, the diffusion is done on the scrambled image based on cryptographic primitive operations and the incorporation of LFSR and chaotic systems as round keys. The hybrid compound of LFSR, chaotic system and cryptographic primitive operations strengthen the encryption performance and enlarge the key space required to resist the brute force attacks. Results of statistical and differential analysis show that the proposed algorithm has high security for secure digital images. Furthermore, it has key sensitivity together with a large key space and is very fast compared to other competitive algorithms.

  14. New optical and radio frequency angular tropospheric refraction models for deep space applications

    Science.gov (United States)

    Berman, A. L.; Rockwell, S. T.

    1976-01-01

    The development of angular tropospheric refraction models for optical and radio frequency usage is presented. The models are compact analytic functions, finite over the entire domain of elevation angle, and accurate over large ranges of pressure, temperature, and relative humidity. Additionally, FORTRAN subroutines for each of the models are included.

  15. MULTILOOP PI CONTROLLER FOR ACHIEVING SIMULTANEOUS TIME AND FREQUENCY DOMAIN SPECIFICATIONS

    OpenAIRE

    2015-01-01

    Most of the controllers in control system are designed to satisfy either time domain or frequency domain specifications. This work presents the computation of a multiloop PI controller for achieving time and frequency domain specifications simultaneously. The desired time and frequency domain measures are to be specified initially to the design. To obtain the desired value of the performance measures the graphical relationship between the PI controller and the performance criteria is given. T...

  16. Frequency domain analysis of noise in autoregulated gene circuits

    Science.gov (United States)

    Simpson, Michael L.; Cox, Chris D.; Sayler, Gary S.

    2003-01-01

    We describe a frequency domain technique for the analysis of intrinsic noise within negatively autoregulated gene circuits. This approach is based on the transfer function around the feedback loop (loop transmission) and the equivalent noise bandwidth of the system. The loop transmission, T, is shown to be a determining factor of the dynamics and the noise behavior of autoregulated gene circuits, and this T-based technique provides a simple and flexible method for the analysis of noise arising from any source within the gene circuit. We show that negative feedback not only reduces the variance of the noise in the protein concentration, but also shifts this noise to higher frequencies where it may have a negligible effect on the noise behavior of following gene circuits within a cascade. This predicted effect is demonstrated through the exact stochastic simulation of a two-gene cascade. The analysis elucidates important aspects of gene circuit structure that control functionality, and may provide some insights into selective pressures leading to this structure. The resulting analytical relationships have a simple form, making them especially useful as synthetic gene circuit design equations. With the exception of the linearization of Hill kinetics, this technique is general and may be applied to the analysis or design of networks of higher complexity. This utility is demonstrated through the exact stochastic simulation of an autoregulated two-gene cascade operating near instability. PMID:12671069

  17. Frequency domain identification of grinding stiffness and damping

    Science.gov (United States)

    Leonesio, Marco; Parenti, Paolo; Bianchi, Giacomo

    2017-09-01

    As equivalent stiffness and damping of the grinding process dominate cutting stability, their identification is essential to predict and avoid detrimental chatter occurrence. The identification of these process constants is not easy in large cylindrical grinding machines, e.g. roll grinders, since there are no practical ways to measure cutting force normal component. This paper presents a novel frequency domain approach for identifying these process parameters, exploiting in-process system response, measured via impact testing. This method adopts a sub-structuring approach to couple the wheel-workpiece relative dynamic compliance with a two-dimensional grinding force model that entails both normal and tangential directions. The grinding specific energy and normal force ratio, that determine grinding stiffness and damping, are identified by fitting the closed loop FRF (Frequency Response Function) measured during specific plunge-grinding tests. The fitting quality supports the predictive capability of the model. Eventually, the soundness of the proposed identification procedure is further assessed by comparing the grinding specific energy identified through standard cutting power measurements.

  18. Spectral domain optical coherence tomography and microperimetry in foveal hypoplasia

    Directory of Open Access Journals (Sweden)

    Swakshyar Saumya Pal

    2011-01-01

    Full Text Available A case of foveal hypoplasia associated with ocular albinism with anatomic and functional changes by various techniques using spectral domain optical coherence tomography (SD-OCT, microperimeter and confocal scanning laser ophthalmoscope is described. This case highlights the importance of microperimeter in detecting the functional abnormalities of vision and SD-OCT in identifying the retinal laminar abnormalities in foveal hypoplasia.

  19. Determination of beam coupling impedance in the frequency domain

    Energy Technology Data Exchange (ETDEWEB)

    Niedermayer, Uwe

    2016-07-01

    The concept of beam coupling impedance describes the electromagnetic interaction of uniformly moving charged particles with their surrounding structures in the Frequency Domain (FD). In synchrotron accelerators, beam coupling impedances can lead to beam induced component heating and coherent beam instabilities. Thus, in order to ensure the stable operation of a synchrotron, its impedances have to be quantified and their effects have to be controlled. Nowadays, beam coupling impedances are mostly obtained by Fourier transform of wake potentials, which are the results of Time Domain (TD) simulations. However, at low frequencies, low beam velocity, or for dispersive materials, TD simulations become unhandy. In this area, analytical calculations of beam coupling impedance in the FD, combined with geometry approximations, are still widely used. This thesis describes the development of two electromagnetic field solvers to obtain the beam coupling impedance directly in the FD, where the beam velocity is only a parameter and dispersive materials can be included easily. One solver is based on the Finite Integration Technique (FIT) on a staircase mesh. It is implemented both in 2D and 3D. However, the staircase mesh is inefficient on curved structures, which is particularly problematic for the modeling of a dipole source, that is required for the computation of the transverse beam coupling impedance. This issue is overcome by the second solver developed in this thesis, which is based on the Finite Element Method (FEM) on an unstructured triangular mesh. It is implemented in 2D and includes an optional Surface Impedance Boundary Condition (SIBC). Thus, it is well suited for the computation of longitudinal and transverse impedances of long beam pipe structures of arbitrary cross-section. Besides arbitrary frequency and beam velocity, also dispersive materials can be chosen, which is crucial for the computation of the impedance of ferrite kicker magnets. Numerical impedance

  20. Phase-coherent all-optical frequency division by three

    NARCIS (Netherlands)

    Lee, Dong-Hoon; Klein, M.E.; Meyn, Jan-Peter; Wallenstein, Richard; Gross, P.; Boller, Klaus J.

    2003-01-01

    The properties of all-optical phase-coherent frequency division by 3, based on a self-phase-locked continuous-wave (cw) optical parametric oscillator (OPO), are investigated theoretically and experimentally. The frequency to be divided is provided by a diode laser master-oscillator power-amplifier

  1. On time-domain and frequency-domain MMSE-based TEQ design for DMT transmission

    CERN Document Server

    Vanbleu, K; Moonen, M; Ysebaert, G; 10.1109/TSP.2005.851161

    2005-01-01

    We reconsider the minimum mean square error (MMSE) time-domain equalizer (TEQ), bitrate maximizing TEQ (BM-TEQ), and per-tone equalizer design (PTEQ) for discrete multitone (DMT) transmission and cast them in a common least-squares (LS) based framework. The MMSE- TEQ design criterion can be formulated as a constrained linear least-squares (CLLS) criterion that minimizes a time-domain (TD) error energy. From this CLLS-based TD-MMSE-TEQ criterion, we derive two new least-squares (LS) based frequency-domain (FD) MMSE-TEQ design criteria: a CLLS-based FD-MMSE-TEQ criterion and a so-called separable nonlinear LS (SNLLS) based FD-MMSE-TEQ design. Finally, the original BM-TEQ design is shown to be equivalent to a so-called iteratively-reweighted (IR) version of the SNLLS-based FD-MMSE-TEQ design. This LS-based framework then results in the following contributions. The new, IR-SNLLS-based BM-TEQ design criterion gives rise to an elegant, iterative, fast converging, Gauss-Newton-based design algorithm that exploits th...

  2. Stabilisation of a fibre frequency synthesiser using acousto-optical and electro-optical modulators

    Science.gov (United States)

    Koliada, N. A.; Nyushkov, B. N.; Pivtsov, V. S.; Dychkov, A. S.; Farnosov, S. A.; Denisov, V. I.; Bagayev, S. N.

    2016-12-01

    A fibre-optic frequency synthesiser is developed that is stabilised to the optical frequency standard based on molecular iodine ({\\text{Nd : YAG/I}}2). The possibility of transferring stability of the optical frequency standard to other optical frequencies in the IR range 1 - 2 \\unicode{956}{\\text{m}} and to the RF range by using synthesiser phase-locked loops (PLLs) with acousto-optical and electro-optical modulators is experimentally demonstrated. The additive instability introduced into the optical frequency comb of the synthesiser (which arises due to PLL residual random errors) is several orders less than the intrinsic instability of the reference optical frequency standard employed (i.e., is noticeably less than 1 × 10-13 for 1 {\\text{s}} and 5 × 10-15 for 1000 {\\text{s}}).

  3. Optical network control plane for multi-domain networking

    DEFF Research Database (Denmark)

    Manolova, Anna Vasileva

    This thesis focuses on multi-domain routing for traffice engineering and survivability support in optical transport networks under the Generalized Multi-Protocol Label Switching (GMPLS) control framework. First, different extensions to the Border Gateway Protocol for multi-domain Traffic Engineer......This thesis focuses on multi-domain routing for traffice engineering and survivability support in optical transport networks under the Generalized Multi-Protocol Label Switching (GMPLS) control framework. First, different extensions to the Border Gateway Protocol for multi-domain Traffic...... process are not enough for efficient TE in mesh multi-domain networks. Enhancing the protocol with multi-path dissemination capability, combined with the employment of an end-to-end TE metric proves to be a highly efficient solution. Simulation results show good performance characteristics of the proposed...... is not as essential for improved network performance as the length of the provided paths. Second, the issue of multi-domain survivability support is analyzed. An AS-disjoint paths is beneficial not only for resilience support, but also for facilitating adequate network reactions to changes in the network, which...

  4. Determine electric field directions at semiconductor surfaces by femtosecond frequency domain interferometric second harmonic (FDISH) generation

    Science.gov (United States)

    Nelson, C. A.; Zhu, X.-Y.

    2016-10-01

    Optical excitations at semiconductor surfaces or interfaces are accompanied by transient interfacial electric fields due to charge redistribution or transfer. While such transient fields may be probed by time-resolved second harmonic generation (TR-SHG), it is difficult to determine the field direction, which is invaluable to unveiling the underlying physics. Here we apply a time-resolved frequency domain interferometric second harmonic (TR-FDISH) generation technique to determine the phase relationship between the SH field emitted from bulk GaAs(1 0 0) and the transient SH field from the space charge region. The interference between these two SH fields allow us to unambiguously determine the directions of transient electric fields. Since SH fields from a static bulk contribution and a changing electric field contribution are present at most semiconductor surfaces or interfaces under optical excitation, the TR-FDISH technique is of general significance to probing the dynamics of interfacial charge transfer/redistribution.

  5. Distributed optical multiplexing with precise frequency allocation using fiber frequency conversion

    Science.gov (United States)

    Kato, Tomoyuki; Okabe, Ryo; Watanabe, Shigeki

    2013-12-01

    Effective utilization of fiber capacity in optical communication networks is required to keep up with the increasing traffic demand. Precise optical frequency allocation among carriers is essential for improving the spectral efficiency to utilize the limited spectral resource. In this paper, we show a distributed optical multiplexing scheme, in which data signals are sequentially multiplexed by frequency-division multiplexing on a single-wavelength optical carrier using fiber frequency conversion with locally provided optical subcarrier signals. The scheme achieves dense packing of distributed multi-channel signals with precise frequency allocation using free-running lasers. Using the scheme we demonstrate a precise multiplexing of coherent-optical orthogonal frequency-division multiplexing and Nyquist wavelength-division multiplexing.

  6. Non-stationary frequency domain system identification using time-frequency representations

    Science.gov (United States)

    Guo, Yanlin; Kareem, Ahsan

    2016-05-01

    System properties of buildings and bridges may vary with time due to temperature changes, aging or extreme loadings. To identify these time-varying system properties, this study proposes a new output-only non-stationary system identification (SI) framework based on instantaneous or marginal spectra derived from the time-frequency representation, e.g., short time Fourier or wavelet transform. Spectra derived from these time-frequency representations are very popular in tracking time-varying frequencies; however, they have seldom been used to identify the time-varying damping ratio because a short window needed to capture the time-varying information amplifies the bandwidth significantly, which may lead to considerably overestimating the damping ratio. To overcome this shortcoming, this study modifies the theoretical frequency response function (FRF) to explicitly account for the windowing effect, and therefore enables SI directly using instantaneous or marginal spectra derived from the wavelet or short time Fourier transform. The response spectrum estimated using the short time window and the modified FRF are both influenced by the same time window, thus the instantaneous or time-localized marginal spectrum of response can be fitted to the modified FRF to identify frequency and damping ratio at each time instant. This spectral-based SI framework can reliably identify damping in time-varying systems under non-stationary excitations. The efficacy of the proposed framework is demonstrated by both numerical and full-scale examples, and also compared to the time-domain SI method, stochastic subspace identification (SSI), since the time-domain SI approaches and their extensions are popular in identifying time-varying systems utilizing recursive algorithms or moving windows.

  7. Interpretations of frequency domain analyses of neural entrainment: periodicity, fundamental frequency, and harmonics

    Directory of Open Access Journals (Sweden)

    Hong eZhou

    2016-06-01

    Full Text Available Brain activity can follow the rhythms of dynamic sensory stimuli, such as speech and music, a phenomenon called neural entrainment. It has been hypothesized that low-frequency neural entrainment in the neural delta and theta bands provides a potential mechanism to represent and integrate temporal information. Low-frequency neural entrainment is often studied using periodically changing stimuli and is analyzed in the frequency domain using the Fourier analysis. The Fourier analysis decomposes a periodic signal into harmonically related sinusoids. However, it is not intuitive how these harmonically related components are related to the response waveform. Here, we explain the interpretation of response harmonics, with a special focus on very low-frequency neural entrainment near 1 Hz. It is illustrated why neural responses repeating at f Hz do not necessarily generate any neural response at f Hz in the Fourier spectrum. A strong neural response at f Hz indicates that the time scales of the neural response waveform within each cycle match the time scales of the stimulus rhythm. Therefore, neural entrainment at very low frequency implies not only that the neural response repeats at f Hz but also that each period of the neural response is a slow wave matching the time scale of a f Hz sinusoid.

  8. Full stabilization of a microresonator-based optical frequency comb.

    Science.gov (United States)

    Del'Haye, P; Arcizet, O; Schliesser, A; Holzwarth, R; Kippenberg, T J

    2008-08-01

    We demonstrate control and stabilization of an optical frequency comb generated by four-wave mixing in a monolithic microresonator with a mode spacing in the microwave regime (86 GHz). The comb parameters (mode spacing and offset frequency) are controlled via the power and the frequency of the pump laser, which constitutes one of the comb modes. Furthermore, generation of a microwave beat note at the comb's mode spacing frequency is demonstrated, enabling direct stabilization to a microwave frequency standard.

  9. [Frequency-domain quantification based on the singular value decomposition and frequency-selection for magnetic resonance spectra].

    Science.gov (United States)

    Men, Kuo; Quan, Hong; Yang, Peipei; Cao, Ting; Li, Weihao

    2010-04-01

    The frequency-domain magnetic resonance spectroscopy (MRS) is achieved by the Fast Fourier Transform (FFT) of the time-domain signals. Usually we are only interested in the portion lying in a frequency band of the whole spectrum. A method based on the singular value decomposition (SVD) and frequency-selection is presented in this article. The method quantifies the spectrum lying in the interested frequency band and reduces the interference of the parts lying out of the band in a computationally efficient way. Comparative experiments with the standard time-domain SVD method indicate that the method introduced in this article is accurate and timesaving in practical situations.

  10. Semi-automatic, octave-spanning optical frequency counter.

    Science.gov (United States)

    Liu, Tze-An; Shu, Ren-Huei; Peng, Jin-Long

    2008-07-07

    This work presents and demonstrates a semi-automatic optical frequency counter with octave-spanning counting capability using two fiber laser combs operated at different repetition rates. Monochromators are utilized to provide an approximate frequency of the laser under measurement to determine the mode number difference between the two laser combs. The exact mode number of the beating comb line is obtained from the mode number difference and the measured beat frequencies. The entire measurement process, except the frequency stabilization of the laser combs and the optimization of the beat signal-to-noise ratio, is controlled by a computer running a semi-automatic optical frequency counter.

  11. Perfect imaging in the optical domain using dielectric materials

    CERN Document Server

    Gabrielli, Lucas H; Lipson, Michal

    2010-01-01

    The promise of perfect imaging in the optical domain, where light can be imaged without aberrations and with ultra-high resolution, could revolutionize technology and nanofabrication [1, 2, 3, 4, 5, 6]. Recently it has been shown theoretically that perfect imaging can be achieved in a dielectric medium with spatially varying refractive index [7, 8]. The lens geometry is defined using transformation optics [9, 10, 11, 12, 13, 14, 15] for projecting a spherical space onto a real plane space, forming Maxwells fish eye [16, 17, 18, 19]. Most transformation optics demonstrations have been achieved for Euclidean spaces and in the microwave regime, due to ease of fabrication. Here we demonstrate a transformation to a non-Euclidean space [20] in the optical regime using silicon nanophotonic structures.

  12. Multiscale Point Correspondence Using Feature Distribution and Frequency Domain Alignment

    Directory of Open Access Journals (Sweden)

    Zeng-Shun Zhao

    2012-01-01

    Full Text Available In this paper, a hybrid scheme is proposed to find the reliable point-correspondences between two images, which combines the distribution of invariant spatial feature description and frequency domain alignment based on two-stage coarse to fine refinement strategy. Firstly, the source and the target images are both down-sampled by the image pyramid algorithm in a hierarchical multi-scale way. The Fourier-Mellin transform is applied to obtain the transformation parameters at the coarse level between the image pairs; then, the parameters can serve as the initial coarse guess, to guide the following feature matching step at the original scale, where the correspondences are restricted in a search window determined by the deformation between the reference image and the current image; Finally, a novel matching strategy is developed to reject the false matches by validating geometrical relationships between candidate matching points. By doing so, the alignment parameters are refined, which is more accurate and more flexible than a robust fitting technique. This in return can provide a more accurate result for feature correspondence. Experiments on real and synthetic image-pairs show that our approach provides satisfactory feature matching performance.

  13. A frequency domain based rigid motion artifact reduction algorithm

    Science.gov (United States)

    Luo, Hai; Huang, Xiaojie; Pan, Wenyu; Zhou, Heqin; Feng, Huanqing

    2009-10-01

    During a CT scan, patients' conscious or unconscious motions would result in motion artifacts which undermine the image quality and hamper doctors' accurate diagnosis and therapy. It is desirable to develop a precise motion estimation and artifact reduction method in order to produce high-resolution images. Rigid motion can be decomposed into two components: translational motion and rotational motion. Since considering the rotation and translation simultaneously is very difficult, most former studies on motion artifact reduction ignore rotation. The extended HLCC based method considering the rotation and translation simultaneously relies on a searching algorithm which leads to expensive computing cost. Therefore, a novel method which does not rely on searching is desirable. In this paper, we focus on parallel-beam CT. We first propose a frequency domain based method to estimate rotational motion, which is not affected by translational motion. It realizes the separation of rotation estimation and translation estimation. Then we combine this method with the HLCC based method to construct a new method for general rigid motion called separative estimation and collective correction method. Furthermore, we present numerical simulation results to show the accuracy and robustness of our approach.

  14. Simulation of DLA grating structures in the frequency domain

    Science.gov (United States)

    Egenolf, T.; Boine-Frankenheim, O.; Niedermayer, U.

    2017-07-01

    Dielectric laser accelerators (DLA) driven by ultrashort laser pulses can reach orders of magnitude larger gradients than contemporary RF electron accelerators. A new implemented field solver based on the finite element method in the frequency domain allows the efficient calculation of the structure constant, i.e. the ratio of energy gain to laser peak amplitude. We present the maximization of this ratio as a parameter study looking at a single grating period only. Based on this optimized shape the entire design of a beta-matched grating is completed in an iterative process. The period length of a beta-matched grating increases due to the increasing velocity of the electron when a subrelativistic beam is accelerated. The determination of the optimal length of each grating period thus requires the knowledge of the energy gain within all so far crossed periods. Furthermore, we outline to reverse the excitation in the presented solver for beam coupling impedance calculations and an estimation of the beam loading intensity limit.

  15. High-speed optical correlation-domain reflectometry without using acousto-optic modulator

    CERN Document Server

    Shizuka, Makoto; Hayashi, Neisei; Mizuno, Yosuke; Nakamura, Kentaro

    2015-01-01

    To achieve a distributed reflectivity measurement along an optical fiber, we develop a simplified cost-effective configuration of optical correlation- (or coherence-) domain reflectometry based on a synthesized optical coherence function by sinusoidal modulation. By excluding conventional optical heterodyne detection (practically, without using an acousto-optic modulator) and by exploiting the foot of the Fresnel reflection spectrum, the electrical bandwidth required for signal processing is lowered down to several megahertz. We evaluate the basic system performance and demonstrate its high-speed operation (10 ms for one scan) by tracking a moving reflection point in real time.

  16. Distributed acoustic mapping based on interferometry of phase optical time-domain reflectometry

    Science.gov (United States)

    Wang, Chang; Wang, Chen; Shang, Ying; Liu, Xiaohui; Peng, Gangding

    2015-07-01

    We demonstrate the design and characterization of a distributed optical fiber sensing system based on Michelson interferometer of the phase sensitive optical time domain reflectometer (φ-OTDR) for acoustic measurement. Phase, amplitude, frequency response and location information can be directly obtained at the same time by using the passive 3×3 coupler demodulation. In order to simulate sound profiles of seismic or hydroacoustic imaging, experiments on detection of multiple piezoelectric transducers (PZT) are carried out. The result shows that our system can well demodulate different acoustic sources with different intensities.

  17. Interferometric distributed sensing system with phase optical time-domain reflectometry

    Science.gov (United States)

    Wang, Chen; Shang, Ying; Liu, Xiaohui; Wang, Chang; Wang, Hongzhong; Peng, Gangding

    2016-11-01

    We demonstrate a distributed optical fiber sensing system based on the Michelson interferometer of the phase sensitive optical time domain reflectometer (φ-OTDR) for acoustic measurement. Phase, amplitude, frequency response, and location information can be directly obtained at the same time by using the passive 3×3 coupler demodulation. We also set an experiment and successfully restore the acoustic information. Meanwhile, our system has preliminary realized acoustic-phase sensitivity around -150 dB (re rad/μPa) in the experiment.

  18. New frontiers in time-domain diffuse optics, a review

    Science.gov (United States)

    Pifferi, Antonio; Contini, Davide; Mora, Alberto Dalla; Farina, Andrea; Spinelli, Lorenzo; Torricelli, Alessandro

    2016-09-01

    The recent developments in time-domain diffuse optics that rely on physical concepts (e.g., time-gating and null distance) and advanced photonic components (e.g., vertical cavity source-emitting laser as light sources, single photon avalanche diode, and silicon photomultipliers as detectors, fast-gating circuits, and time-to-digital converters for acquisition) are focused. This study shows how these tools could lead on one hand to compact and wearable time-domain devices for point-of-care diagnostics down to the consumer level and on the other hand to powerful systems with exceptional depth penetration and sensitivity.

  19. CHOROIDAL IMAGING USING SPECTRAL-DOMAIN OPTICAL COHERENCE TOMOGRAPHY

    Science.gov (United States)

    Regatieri, Caio V.; Branchini, Lauren; Fujimoto, James G.; Duker, Jay S.

    2012-01-01

    Background A structurally and functionally normal choroidal vasculature is essential for retinal function. Therefore, a precise clinical understanding of choroidal morphology should be important for understanding many retinal and choroidal diseases. Methods PUBMED (http://www.ncbi.nlm.nih.gov/sites/entrez?db=pubmed) was used for most of the literature search for this article. The criterion for inclusion of an article in the references for this review was that it included materials about both the clinical and the basic properties of choroidal imaging using spectral-domain optical coherence tomography. Results Recent reports show successful examination and accurate measurement of choroidal thickness in normal and pathologic states using spectral-domain optical coherence tomography systems. This review focuses on the principles of the new technology that make choroidal imaging using optical coherence tomography possible and on the changes that subsequently have been documented to occur in the choroid in various diseases. Additionally, it outlines future directions in choroidal imaging. Conclusion Optical coherence tomography is now proven to be an effective noninvasive tool to evaluate the choroid and to detect choroidal changes in pathologic states. Additionally, choroidal evaluation using optical coherence tomography can be used as a parameter for diagnosis and follow-up. PMID:22487582

  20. Brillouin optical time-domain analyzer for extended sensing range using probe dithering and cyclic coding

    Science.gov (United States)

    Iribas, Haritz; Loayssa, Alayn; Sauser, Florian; Llera, Miguel; Le Floch, Sébastien

    2017-04-01

    We present an enhanced performance Brillouin optical time-domain analysis sensor that uses dual probes waves with optical frequency modulation and cyclic coding. The frequency modulation serves to increase the probe power that can be injected in the fiber before the onset of non-local effects and noise generated by spontaneous Brillouin scattering. This leads to higher detected signal-to-noise ratio (SNR), which is further increased by the coding gain. The enhanced SNR translates to extended range for the sensor, with experiments demonstrating 1-m spatial resolution over a 164 km fiber loop with a 3-MHz Brillouin frequency shift measurement precision at the worst contrast position. In addition, we introduce a study of the power limits that can be injected in the fiber with cyclic coding before the appearance of distortions in the decoded signal.

  1. All-optical signal processing of OTDM and OFDM signals based on time-domain Optical Fourier Transformation

    DEFF Research Database (Denmark)

    Clausen, Anders; Guan, Pengyu; Mulvad, Hans Christian Hansen

    2014-01-01

    All-optical time-domain Optical Fourier Transformation utilised for signal processing of ultra-high-speed OTDM signals and OFDM signals will be presented.......All-optical time-domain Optical Fourier Transformation utilised for signal processing of ultra-high-speed OTDM signals and OFDM signals will be presented....

  2. Spacial and Frequency Domain Calculation of Terrain Roughness Metric Root-Mean-Square (RMS)

    Science.gov (United States)

    2014-11-01

    TARDEC Technical Report No. 26042 November 2014 SPACIAL AND FREQUENCY DOMAIN CALCULATION OF TERRAIN ROUGHNESS METRIC ROOT-MEAN...DATE (DD-MM-YYYY) 11-15-2014 2. REPORT TYPE TECHNICAL 3. DATES COVERED (From - To) 2013-2014 SPACIAL AND FREQUENCY DOMAIN CALCULATION OF TERRAIN...roughness. Based on mathematics of the Fourier transform and duality, calculations are performed in the spacial and frequency domains to show equivalent

  3. Numerical Solution for Fractional-Order Differential Systems with Time-Domain and Frequency-Domain Methods

    Institute of Scientific and Technical Information of China (English)

    Ke Xiao; Shang-Bo Zhou; Wei-Wei Zhang

    2008-01-01

    For a general nonlinear fractional-orderdifferential equation, the numerical solution is a goodway to approximate the trajectory of such systems. Inthis paper, a novel algorithm for numerical solution offractional-order differential equations based on thedefinition of Grunwald-Letnikov is presented. Theresults of numerical solution by using the novel methodand the frequency-domain method are compared, and the limitations of frequency-domain method arediscussed.

  4. Numerical Solution for Fractional-Order Differential Systems with Time-Domain and Frequency-Domain Methods

    Institute of Scientific and Technical Information of China (English)

    Ke Xiao; Shang-Bo Zhou; Wei-Wei Zhang

    2008-01-01

    For a general nonlinear fractional-order differential equation, the numerical solution is a good way to approximate the trajectory of such systems. In this paper, a novel algorithm for numerical solution of fractional-order differential equations based on the definition of Grunwald-Letnikov is presented. The results of numerical solution by using the novel method and the frequency-domain method are compared, and the limitations of frequency-domain method arediscussed.

  5. Frequency modulation via the Doppler effect in optical fibers.

    Science.gov (United States)

    Oberson, P; Huttner, B; Gisin, N

    1999-04-01

    We present the principle of optical frequency modulation via the Doppler effect obtained by rapidly stretching an optical fiber and thus modifying the optical path of the light propagating in the fiber. This procedure creates a pure frequency shift, with no degradation of the spectrum. Moreover, the effect is wavelength independent and can therefore be applied to any type of light source. We show an experimental realization in which a frequency excursion of ~100 MHz was obtained with a bobbin vibrating at 180 Hz.

  6. Optical frequency tripling with improved suppression and sideband selection.

    Science.gov (United States)

    Thakur, Manoj P; Medeiros, Maria C R; Laurêncio, Paula; Mitchell, John E

    2011-12-12

    A novel optical dispersion tolerant millimetre-wave radio-over-fibre system using optical frequency tripling technique with enhanced and selectable sideband suppression is demonstrated. The implementation utilises cascaded optical modulators to achieve either an optical single sideband (OSSB) or double sideband-suppressed carrier (DSB-SC) signal with high sideband suppression. Our analysis and simulation results indicate that the achievable suppression ratio of this configuration is only limited by other system factors such as optical noise and drifting of the operational conditions. The OSSB transmission system performance is assessed experimentally by the transport of 4 WiMax channels modulating a 10 GHz optical upconverted RF carrier as well as for optical frequency doubling and tripling. The 10 GHz and tripled carrier at 30 GHz are dispersion tolerant resulting both in an average relative constellation error (RCE) of -28.7 dB after 40 km of fibre.

  7. Comparison of pulse and SFCW GPR in time, frequency and wavelet domain

    Science.gov (United States)

    De Pue, Jan; Van De Vijver, Ellen; Cornelis, Wim; Van Meirvenne, Marc

    2014-05-01

    Ground penetrating radar (GPR) systems operating in the time- or frequency domain are two fundamentally different concepts, pursuing the same objective: non-invasive characterization of the subsurface. The aim of this study is to compare the performance of these two GPR systems in the time, frequency and wavelet domain. The time domain GPR investigated is the Utilityscan DF. This is a ground coupled GPR with a digital dual-frequency antenna (300 and 800 MHz). The Geoscope GS3F and VX1213 antenna array from 3DRadar is the frequency domain GPR used in this comparison. It is an air coupled stepped frequency continuous wave (SFCW) GPR with a frequency bandwidth from 200 MHz to 3000 MHz. Using data from several test sites of various soil types, the data is evaluated in the time domain, the frequency domain and the wavelet domain. Each of these domains contains specific information regarding the data quality. Presenting the data in the time domain, allows visualizing the subsurface reflections. This makes it visible how strong the data is affected by internal interference, ringing and other noise. To compensate for the attenuation of the signal in time, automatic gain control is applied. The maximum of this gain function indicates the time where the signal is attenuated completely and noise becomes more dominant, corresponding with the maximal penetration depth of the different GPR systems. In the frequency domain, the data allows to investigate which frequencies contain most valuable information and which ones are affected by noise. Finally, by performing a wavelet transformation the data is transformed to the time-frequency domain. Due to frequency dependent attenuation of electromagnetic signals in the soil, low frequencies will be more dominant in deeper layers, and high frequencies will not be present anymore. This is determining for the range resolution of the data throughout the traveltime of the signal. This work is a contribution to COST Action TU1208 "Civil

  8. Brillouin optical time-domain analysis for geotechnical monitoring

    Institute of Scientific and Technical Information of China (English)

    L. Zeni; L. Picarelli; B. Avolio; A. Coscetta; R. Papa; G. Zeni; C. Di Maio; R. Vassallo; A. Minardo

    2015-01-01

    In this paper, we show some recent experimental applications of Brillouin optical time-domain analysis (BOTDA) based sensors for geotechnical monitoring. In particular, how these sensors can be applied to detecting early movements of soil slopes by the direct embedding of suitable fiber cables in the ground is presented. Furthermore, the same technology can be used to realize innovative inclinometers, as well as smart foundation anchors.

  9. Submicron Resolution Spectral-Domain Optical Coherence Tomography

    KAUST Repository

    Alarousu, Erkki

    2013-11-14

    Apparatuses and systems for submicron resolution spectral-domain optical coherence tomography (OCT) are disclosed. The system may use white light sources having wavelengths within 400-1000 nanometers, and achieve resolution below 1 .mu.m. The apparatus is aggregated into a unitary piece, and a user can connect the apparatus to a user provided controller and/or light source. The light source may be a supercontinuum source.

  10. Sources of noise in Brillouin optical time-domain analyzers

    OpenAIRE

    Urricelqui Polvorinos, Javier; Soto, Marcelo A.; Thévenaz, Luc

    2015-01-01

    This paper presents a thorough study of the different sources of noise affecting Brillouin optical time-domain analyzers (BOTDA), providing a deep insight into the understanding of the fundamental limitations of this kind of sensors. Analytical and experimental results indicate that the noise source ultimately fixing the sensor performance depends basically on the fiber length and the input pump-probe powers. Thus, while the phase-to-intensity noise conversion induced by stimulated Brillouin ...

  11. Optical Frequency Upconversion Technique for Transmission of Wireless MIMO-Type Signals over Optical Fiber

    OpenAIRE

    R. Q. Shaddad; Mohammad, A. B.; S. A. Al-Gailani; Al-Hetar, A. M.

    2014-01-01

    The optical fiber is well adapted to pass multiple wireless signals having different carrier frequencies by using radio-over-fiber (ROF) technique. However, multiple wireless signals which have the same carrier frequency cannot propagate over a single optical fiber, such as wireless multi-input multi-output (MIMO) signals feeding multiple antennas in the fiber wireless (FiWi) system. A novel optical frequency upconversion (OFU) technique is proposed to solve this problem. In this paper, the n...

  12. Multicast contention resolution based on time-frequency joint scheduling in elastic optical switching networks

    Science.gov (United States)

    Liu, Huanlin; Li, Yuan; Peng, Han; Huang, Jun; Kong, Deqian

    2017-01-01

    Resolving the optical multicast contention in optical switch node is an effective approach to improve the performance of elastic optical multicast switch. An optical node architecture integrating with output shared all-optical Orthogonal Frequency Division Multiplexing (OFDM) network coding technology and shared feedback fiber delay lines (FDLs) buffer is designed. And a time-frequency joint scheduling strategy (TFJSS) is proposed. In TFJSS, the maximal weighted independent set algorithm is used to select the output packets with no overlapping spectrum among the contending multicast packets. The remaining contention packets are compressed by OFDM network coding with all-optical XOR operation. Hence, the contention is avoided in spectrum domain by encoding the contending unicast/multicast packets and changing the carrier frequency of encoded packets. If the network coding cannot successfully resolve the contending packets, the shared feedback FDLs are called to address the contention in time domain. Compared with the existing node architecture and scheduling algorithm, the simulation results show that the proposed architecture and the TFJSS can reduce the packet loss probability with low delay largely.

  13. Fast Frequency-domain Waveforms for Spin-Precessing Binary Inspirals

    CERN Document Server

    Klein, Antoine; Yunes, Nicolás

    2014-01-01

    The detection and characterization of gravitational wave signals from compact binary coalescence events relies on accurate waveform templates in the frequency domain. The stationary phase approximation (SPA) can be used to compute closed-form frequency-domain waveforms for non-precessing, quasi-circular binary inspirals. However, until now, no fast frequency-domain waveforms have existed for generic, spin-precessing quasi-circular compact binary inspirals. Templates for these systems have had to be computed via a discrete Fourier transform of finely sampled time-domain waveforms, which is far more computationally expensive than those constructed directly in the frequency-domain, especially for those systems that are dominated by the inspiral part. There are two obstacles to deriving frequency-domain waveforms for precessing systems: (i) the spin-precession equations do not admit closed-form solutions for generic systems; (ii) the SPA fails catastrophically. Presently there is no general solution to the first ...

  14. Magnetic Force Between Magnetic Nano Probes at Optical Frequency

    CERN Document Server

    Guclu, Caner; Capolino, Filippo

    2014-01-01

    Magnetic force microscopy based on the interaction of static magnetic materials was demonstrated in the past with resolutions in the order of nanometers. Measurement techniques based on forces between electric dipoles oscillating at optical frequencies have been also demonstrated leading to the standard operation of the scanning force microscope (SFM). However the investigations of a SFM based on the magnetic force generated by magnetic dipole moments oscillating at optical frequencies has not been tackled yet. With this goal in mind we establish a theoretical model towards observable magnetic force interaction between two magnetically polarizable nanoparticles at optical frequency and show such a force to be in the order of piconewtons which could be in principle detected by conventional microscopy techniques. Two possible principles for conceiving magnetically polarizable nano probes able to generate strong magnetic dipoles at optical frequency are investigated based on silicon nanoparticles and on clusters...

  15. Multiplexed sub-Doppler spectroscopy with an optical frequency comb

    CERN Document Server

    Long, David A; Plusquellic, David F; Hodges, Joseph T

    2016-01-01

    An optical frequency comb generated with an electro-optic phase modulator and a chirped radiofrequency waveform is used to perform saturation and pump-probe spectroscopy on the $D_1$ and $D_2$ transitions of atomic potassium. With a comb tooth spacing of 200 kHz and an optical bandwidth of 2 GHz the hyperfine transitions can be simultaneously observed. Interferograms are recorded in as little as 5 $\\mu$s (a timescale corresponding to the inverse of the comb tooth spacing). Importantly, the sub-Doppler features can be measured as long as the laser carrier frequency lies within the Doppler profile, thus removing the need for slow scanning or a priori knowledge of the frequencies of the sub-Doppler features. Sub-Doppler optical frequency comb spectroscopy has the potential to dramatically reduce acquisition times and allow for rapid and accurate assignment of complex molecular and atomic spectra which are presently intractable.

  16. Photonic chip based optical frequency comb using soliton induced Cherenkov radiation

    CERN Document Server

    Brasch, Victor; Geiselmann, Michael; Lihachev, Grigoriy; Pfeiffer, Martin H P; Gorodetsky, Michael L; Kippenberg, Tobias J

    2014-01-01

    By continuous wave pumping of a dispersion engineered, planar silicon nitride microresonator, continuously circulating, sub-30fs short temporal dissipative solitons are generated, that correspond to pulses of 6 optical cycles and constitute a coherent optical frequency comb in the spectral domain. Emission of soliton induced Cherenkov radiation caused by higher order dispersion broadens the spectral bandwidth to 2/3 of an octave, sufficient for self referencing, in excellent agreement with recent theoretical predictions and the broadest coherent microresonator frequency comb generated to date. The ability to preserve coherence over a broad spectral bandwidth using soliton induced Cherenkov radiation marks a critical milestone in the development of planar optical frequency combs, enabling on one hand application in e.g. coherent communications, broadband dual comb spectroscopy and Raman spectral imaging, while on the other hand significantly relaxing dispersion requirements for broadband microresonator frequen...

  17. Colloidal superlattices for unnaturally high-index metamaterials at broadband optical frequencies.

    Science.gov (United States)

    Lee, Seungwoo

    2015-11-02

    The recent advance in the assembly of metallic nanoparticles (NPs) has enabled sophisticated engineering of unprecedented light-matter interaction at the optical domain. In this work, I expand the design flexibility of NP optical metamaterial to push the upper limit of accessible refractive index to the unnaturally high regime. The precise control over the geometrical parameters of NP superlattice monolayer conferred the dramatic increase in electric resonance and related effective permittivity far beyond the naturally accessible regime. Simultaneously, effective permeability change, another key factor to achieving high refractive index, was effectively suppressed by reducing the thickness of NPs. By establishing this design rule, I have achieved unnaturally high refractive index (15.7 at the electric resonance and 7.3 at the quasi-static limit) at broadband optical frequencies (100 THz ~300 THz). I also combined this NP metamaterial with graphene to electrically control the high refractive index over the broad optical frequencies.

  18. WDM-CAP-PON integration with VLLC system based on optical frequency comb

    Science.gov (United States)

    He, Jing; Dong, Huan; Deng, Rui; Shi, Jin; Chen, Lin

    2016-09-01

    In this paper, a wavelength division multiplexing carrier-less amplitude phase modulation passive optical network (WDM-CAP-PON) integration with visible laser light communication (VLLC) system is proposed and experimentally demonstrated. To reduce the cost of WDM system, the optical frequency comb scheme using one Mach-Zehnder modulator (MZM) is utilized and five flat optical combs can be generated. Meanwhile, a blue laser diode (LD) as a VLLC optical source can provide high data rate and long transmission distance. Utilizing overlap frequency domain equalization (OFDE) and negative chirp of MZM, the system performance in both Q-factor and receiver sensitivity can be improved. After 20 km standard single mode fiber (SSMF) and 4.5 m free space transmission, the experimental results show that 10 Gb/s CAP signal can be achieved under 7% forward error correction (FEC) limit of 3 . 8 × 10-3.

  19. The Optically Pumped Cs Frequency Standard at the NRLM

    Science.gov (United States)

    1987-12-01

    References 1. J.L. Picqu6, "Hyperfine optical pumping of a cesium atomic beam, and applications," Metrologia, vo1.13, pp.115-119, 1977. 2. M. Arditi and... Arditi , "A caesium beam atomic clock with laser optical pumping, as a potential frequency standard," Metrologia, vo1.18, pp.59-66, 1982. 4. G

  20. Portable (handheld) clinical device for quantitative spectroscopy of skin, utilizing spatial frequency domain reflectance techniques

    Science.gov (United States)

    Saager, Rolf B.; Dang, An N.; Huang, Samantha S.; Kelly, Kristen M.; Durkin, Anthony J.

    2017-09-01

    Spatial Frequency Domain Spectroscopy (SFDS) is a technique for quantifying in-vivo tissue optical properties. SFDS employs structured light patterns that are projected onto tissues using a spatial light modulator, such as a digital micromirror device. In combination with appropriate models of light propagation, this technique can be used to quantify tissue optical properties (absorption, μa, and scattering, μs', coefficients) and chromophore concentrations. Here we present a handheld implementation of an SFDS device that employs line (one dimensional) imaging. This instrument can measure 1088 spatial locations that span a 3 cm line as opposed to our original benchtop SFDS system that only collects a single 1 mm diameter spot. This imager, however, retains the spectral resolution (˜1 nm) and range (450-1000 nm) of our original benchtop SFDS device. In the context of homogeneous turbid media, we demonstrate that this new system matches the spectral response of our original system to within 1% across a typical range of spatial frequencies (0-0.35 mm-1). With the new form factor, the device has tremendously improved mobility and portability, allowing for greater ease of use in a clinical setting. A smaller size also enables access to different tissue locations, which increases the flexibility of the device. The design of this portable system not only enables SFDS to be used in clinical settings but also enables visualization of properties of layered tissues such as skin.

  1. Wide-field quantitative imaging of tissue microstructure using sub-diffuse spatial frequency domain imaging.

    Science.gov (United States)

    McClatchy, David M; Rizzo, Elizabeth J; Wells, Wendy A; Cheney, Philip P; Hwang, Jeeseong C; Paulsen, Keith D; Pogue, Brian W; Kanick, Stephen C

    2016-06-20

    Localized measurements of scattering in biological tissue provide sensitivity to microstructural morphology but have limited utility to wide-field applications, such as surgical guidance. This study introduces sub-diffusive spatial frequency domain imaging (sd-SFDI), which uses high spatial frequency illumination to achieve wide-field sampling of localized reflectances. Model-based inversion recovers macroscopic variations in the reduced scattering coefficient [Formula: see text] and the phase function backscatter parameter (γ). Measurements in optical phantoms show quantitative imaging of user-tuned phase-function-based contrast with accurate decoupling of parameters that define both the density and the size-scale distribution of scatterers. Measurements of fresh ex vivo breast tissue samples revealed, for the first time, unique clustering of sub-diffusive scattering properties for different tissue types. The results support that sd-SFDI provides maps of microscopic structural biomarkers that cannot be obtained with diffuse wide-field imaging and characterizes spatial variations not resolved by point-based optical sampling.

  2. Characterization of static bifurcations for n-dimensional flows in the frequency domain

    Institute of Scientific and Technical Information of China (English)

    Li ZENG; Yi ZHAO

    2006-01-01

    In this paper n-dimensional flows (described by continuous-time system) with static bifurcations are considered with the aim of classification of different elementary bifurcations using the frequency domain formalism. Based on frequency domain approach, we prove some criterions for the saddle-node bifurcation, transcritical bifurcation and pitchfork bifurcation, and give an example to illustrate the efficiency of the result obtained.

  3. The three-layered mismatched media diffusion equation in frequency domain

    Science.gov (United States)

    Wang, Xichang; Wang, Shumei; Meng, Zhaokun; Yang, Shangming

    2006-09-01

    Near-IR radiation has great potential in medical diagnosis and therapy because of the non-invasive nature of light and the selectively poisonous effect to tumors of photodynarnic treatment. Therefore, Near-IR light propagation in highly scattering biological tissue must be understudied for basic research and clinical application of biomedical optics. A tissue is multi-layered mismatched medium, but many investigators only study the diffusion equation of matched medium. they take the tissue as the same refractive index. In order to understand the light transport in tissue, We analyze the diffusion of photons three-layered mismatched medium and set up the solution of Green's function in frequency domain, we employ the extrapolated boundary condition to set up a solution of the diffusion equation. At the same time, we utilize the diffuse equation to calculate the phase in different situation

  4. Fatigue Damage Assessment by Considering Mean Value Effect in Frequency Domain

    Institute of Scientific and Technical Information of China (English)

    丁红岩; 朱奇; 张浦阳

    2015-01-01

    Fatigue damage assessment is carried out considering mean value effect by applying four criteria of failure. Three frequency domain methods, i.e., level crossing counting (LCC), range counting (RC) and a new proposed method, are applied. The core of frequency domain method is the construction of probability density function for the mean stress and stress range of the stress process. The applicability of these frequency domain methods are inspected by comparing with time domain method. Numerical simulations verify the applicability of LCC and the proposed method, while RC gives poor estimations.

  5. Detection of 320 Gb/s Nyquist OTDM by polarization-insensitive time-domain optical Fourier transformation

    DEFF Research Database (Denmark)

    Hu, Hao; Kong, Deming; Palushani, Evarist;

    2013-01-01

    320 Gb/s Nyquist-OTDM is generated by rectangular filtering with a bandwidth of 320 GHz and received by polarization-insensitive time-domain optical Fourier transformation (TD-OFT) followed by passive filtering. After the time-to-frequency mapping in the TD-OFT, the Nyquist-OTDM is converted...

  6. Theoretical analysis and system design of two-photon based optical frequency standards

    Science.gov (United States)

    Burger, J. P.; Jivan, P.; Matthee, C.; Kritzinger, R.; Hussein, H.; Terra, O.

    2014-06-01

    The National Metrology Institute of South Africa (NMISA) is developing a new optical frequency standard based on the Rubidium two-photon transition in collaboration with the National Institute of Standards (NIS, Egypt) that will use both bulk and fiber optics in the system. This is system is called A-POD; an acronym for a portable photonic oscillator device. Rubidium two-photon standards can yield relatively simple and precise standards that are compatible with standard Ti:Sapphire optical frequency combs, as well as the need for a precise frequency standard in the optical telecommunication domain and for measurement of length with a visible beam. The robustness and transportability of the standard are important considerations for the optical frequency standard. This projects implements a framework for better two-photon standards that can be highly accurate, and possibly compete with much more complex clocks in the metrology environment, and especially so in the smaller national metrology institutes found in the developing world. This paper discusses the design constraints and the development considerations towards the optical setup. The robustness and transportability was greatly improved via the usage of optical fiber in the light source of the system, or even in atom-light interaction region. Of particular importance are the beam parameters inside the atomic interaction area. The extent of Doppler broadening and the intensity dependent line shift have to be optimized within practical extents, where both these aspects are affected by the beam shape and optical geometry. A way to fully treat the optical beam effects together with atomic movement is proposed. Furthermore a method is proposed to do real time compensation of intensity dependent light shift, which could have major applicability to frequency standards in general - the complexity is shifted from physical setups to digital signal processing, which is easily adaptable and stable.

  7. Time and Frequency Domain Optimization with Shift, Convolution and Smoothness in Factor Analysis Type Decompositions

    DEFF Research Database (Denmark)

    Madsen, Kristoffer Hougaard; Hansen, Lars Kai; Mørup, Morten

    2009-01-01

    We propose the Time Frequency Gradient Method (TFGM) which forms a framework for optimization of models that are constrained in the time domain while having efficient representations in the frequency domain. Since the constraints in the time domain in general are not transparent in a frequency...... representation we demonstrate how the class of objective functions that are separable in either time or frequency instances allow the gradient in the time or frequency domain to be converted to the opposing domain. We further demonstrate the usefulness of this framework for three different models; Shifted Non......-negative Matrix Factorization, Convolutive Sparse Coding as well as Smooth and Sparse Matrix Factorization. Matlab implementation of the proposed algorithms are available for download at www.erpwavelab.org....

  8. Femtosecond Optical Frequency Comb Technology Principle, Operation and Application

    CERN Document Server

    Ye, Jun

    2005-01-01

    Over the last few years, there has been a remarkable convergence among the fields of ultrafast optics, optical frequency metrology, and precision laser spectroscopy. This convergence has enabled unprecedented advances in control of the electric field of the pulses produced by femtosecond mode-locked lasers. The resulting spectrum consists of a comb of sharp spectral lines with well-defined frequencies. These new techniques and capabilities are generally known as "femtosecond comb technology." They have had dramatic impact on the diverse fields of precision measurement and extreme nonlinear optical physics. This book provides an introductory description of mode-locked lasers, the connection between time and frequency descriptions of their output and the physical origins of the electric field dynamics, together with an overview of applications of femtosecond comb technology. Individual chapters go into more detail on mode-locked laser development, spectral broadening in microstructure fiber, optical parametric ...

  9. The absolute frequency of the 87Sr optical clock transition

    DEFF Research Database (Denmark)

    Campbell, Gretchen K.; Ludlow, Andrew D.; Blatt, Sebastian;

    2008-01-01

    The absolute frequency of the 1S0–3P0 clock transition of 87Sr has been measured to be 429 228 004 229 873.65 (37) Hz using lattice-confined atoms, where the fractional uncertainty of 8.6 × 10-16 represents one of the most accurate measurements of an atomic transition frequency to date. After a d...... is made possible using a femtosecond laser based optical frequency comb to phase coherently connect the optical and microwave spectral regions and by a 3.5 km fibre transfer scheme to compare the remotely located clock signals....

  10. Solving forward and inverse seismic problems by boundary-element method in frequency domain

    Energy Technology Data Exchange (ETDEWEB)

    Xianxi, J.

    1988-01-01

    Solving the boundary value problem of wave equation by boundary element method in frequency domain involves these steps: 1. ID Fourier transform of time variable is made to convert the wave equation into Helmholtz equation; 2. this equation is then solved using boundary-element method in frequency domain; 3. the result is returned to time domain by making inverse Fourier transform. Compared with other formulas, the formula in this paper brings higher accuracy but less computation.

  11. Mechanical control of a microrod-resonator optical frequency comb

    CERN Document Server

    Papp, Scott B; Diddams, Scott A

    2012-01-01

    Robust control and stabilization of optical frequency combs enables an extraordinary range of scientific and technological applications, including frequency metrology at extreme levels of precision, novel spectroscopy of quantum gases and of molecules from visible wavelengths to the far infrared, searches for exoplanets, and photonic waveform synthesis. Here we report on the stabilization of a microresonator-based optical comb (microcomb) by way of mechanical actuation. This represents an important step in the development of microcomb technology, which offers a pathway toward fully-integrated comb systems. Residual fluctuations of our 32.6 GHz microcomb line spacing reach a record stability level of $5\\times10^{-15}$ for 1 s averaging, thereby highlighting the potential of microcombs to support modern optical frequency standards. Furthermore, measurements of the line spacing with respect to an independent frequency reference reveal the effective stabilization of different spectral slices of the comb with a $&...

  12. Mid-Infrared Optical Frequency Combs based on Crystalline Microresonators

    CERN Document Server

    Wang, C Y; Del'Haye, P; Schliesser, A; Hofer, J; Holzwarth, R; Hänsch, T W; Picqué, N; Kippenberg, T J

    2011-01-01

    The mid-infrared spectral range (\\lambda ~ 2 \\mu m to 20 \\mu m) is known as the "molecular fingerprint" region as many molecules have their highly characteristic, fundamental ro-vibrational bands in this part of the electromagnetic spectrum. Broadband mid-infrared spectroscopy therefore constitutes a powerful and ubiquitous tool for optical analysis of chemical components that is used in biochemistry, astronomy, pharmaceutical monitoring and material science. Optical frequency combs, i.e. broad spectral bandwidth coherent light sources consisting of equally spaced sharp lines, have revolutionized optical frequency metrology one decade ago. They now demonstrate dramatically improved acquisition rates, resolution and sensitivity for molecular spectroscopy mostly in the visible and near-infrared ranges. Mid-infrared frequency combs have therefore become highly desirable and recent progress in generating such combs by nonlinear frequency conversion has opened access to this spectral region. Here we report on a pr...

  13. Fast frequency hopping codes applied to SAC optical CDMA network

    Science.gov (United States)

    Tseng, Shin-Pin

    2015-06-01

    This study designed a fast frequency hopping (FFH) code family suitable for application in spectral-amplitude-coding (SAC) optical code-division multiple-access (CDMA) networks. The FFH code family can effectively suppress the effects of multiuser interference and had its origin in the frequency hopping code family. Additional codes were developed as secure codewords for enhancing the security of the network. In considering the system cost and flexibility, simple optical encoders/decoders using fiber Bragg gratings (FBGs) and a set of optical securers using two arrayed-waveguide grating (AWG) demultiplexers (DeMUXs) were also constructed. Based on a Gaussian approximation, expressions for evaluating the bit error rate (BER) and spectral efficiency (SE) of SAC optical CDMA networks are presented. The results indicated that the proposed SAC optical CDMA network exhibited favorable performance.

  14. Resonant Doppler imaging with Fourier domain optical coherence tomography

    Science.gov (United States)

    Leitgeb, Rainer A.; Szklumowska, Anna; Pircher, Michael; Gotzinger, Erich; Fercher, Adolf F.

    2005-04-01

    Fourier Domain Optical Coherene Tomography (FD OCT) is a high speed imaging modality with increased sensitivity as compared to standard time domain (TD) OCT. The higher sensitivity is especially important, if strongly scattering tissue such as blood is investigated. Recently it could be shown that retinal blood flow can be assessed in-vivo by high speed FD OCT. However the detection bandwidth of color Doppler (CD) FDOCT is strongly limited due to blurring of the detected interference fringes during exposure. This leads to a loss of sensitivity for detection of fast changes in tissue. Using a moving mirror as a reference one can effectively increase the detection bandwidth for CD FDOCT and perform perfusion sectioning. The modality is called resonant CD FDOCT imaging. The principle of the method is presented and experimentally verified.

  15. Fingerprint Ridge Frequency Estimation in the Fourier Domain

    Directory of Open Access Journals (Sweden)

    PATRICIU, V.-V.

    2014-11-01

    Full Text Available Ridge frequency is an important parameter in fingerprint image processing and feature extraction. However, ridge frequency estimation is a difficult task in noisy fingerprint images. A simple and accurate method for the computation of fingerprint ridge frequency using the Fourier spectrum is proposed. The results of the experiments conducted on a collection of fingerprints as well as a quantitative method for performance evaluation based on a Gabor filter-bank are presented. The proposed method is robust with respect to noise and reliable frequency images are obtained.

  16. Frequency-domain trade-offs for dielectric elastomer generators

    Science.gov (United States)

    Zanini, Plinio; Rossiter, Jonathan M.; Homer, Martin

    2017-04-01

    Dielectric Elastomer Generators (DEGs) are an emerging energy harvesting technology based on a the cyclic stretching of a rubber-like membrane. However, most design processes do not take into account different excitation frequencies; thus limits the applicability studies since in real-world situations forcing frequency is not often constant. Through the use of a practical design scenario we use modeling and simulation to determine the material frequency response and, hence, carefully investigate the excitation frequencies that maximize the performance (power output, efficiency) of DEGs and the factors that influence it.

  17. Optical Frequency-Modulated Continuous-Wave (FMCW) Interferometry

    CERN Document Server

    Zheng, Jesse

    2005-01-01

    This book introduces the optical frequency-modulated continuous-wave (FMCW) interferometry - a new field of optics that is derived from radar. The study of optical FMCW interference not only updates our knowledge about the nature of light, but also creates an advanced technology for precision measurements. The principles, applications and signal processing of optical FMCW interference are systematically discussed. This book is intended for scientists and engineers in both academia and industry. It is especially suited to professionals who are working in the field of measurement instruments.

  18. Precise Stabilization of the Optical Frequency of WGMRs

    Science.gov (United States)

    Savchenkov, Anatoliy; Matsko, Andrey; Matsko, Andrey; Yu, Nan; Maleki, Lute; Iltchenko, Vladimir

    2009-01-01

    Crystalline whispering gallery mode resonators (CWGMRs) made of crystals with axial symmetry have ordinary and extraordinary families of optical modes. These modes have substantially different thermo-refractive constants. This results in a very sharp dependence of differential detuning of optical frequency on effective temperature. This frequency difference compared with clock gives an error signal for precise compensation of the random fluctuations of optical frequency. Certain crystals, like MgF2, have turnover points where the thermo-refractive effect is completely nullified. An advantage for applications using WGMRs for frequency stabilization is in the possibility of manufacturing resonators out of practically any optically transparent crystal. It is known that there are crystals with negative and zero thermal expansion at some specific temperatures. Doping changes properties of the crystals and it is possible to create an optically transparent crystal with zero thermal expansion at room temperature. With this innovation s stabilization technique, the resultant WGMR will have absolute frequency stability The expansion of the resonator s body can be completely compensated for by nonlinear elements. This results in compensation of linear thermal expansion (see figure). In three-mode, the MgF2 resonator, if tuned at the turnover thermal point, can compensate for all types of random thermal-related frequency drift. Simplified dual-mode method is also available. This creates miniature optical resonators with good short- and long-term stability for passive secondary frequency ethalon and an active resonator for active secondary frequency standard (a narrowband laser with long-term stability).

  19. Molecular Interaction Studies of Benzyl Alcohols with Methacrylates in Carbon Tetrachloride using Frequency Domain Technique

    Directory of Open Access Journals (Sweden)

    S. Radhakrishnan

    2016-08-01

    Full Text Available The dielectric relaxation of benzyl alcohol substitutents (benzyl alcohol, m-methylbenzyl alcohol and m-nitrobenzyl alcohol with methyl methacrylate and butyl methacrylate in dilute solution of carbon tetrachloride is measured at 9.37 GHz using Frequency domain (X-band technique. Different dielectric parameters like dielectric constant (ε׳, dielectric loss factor (ε״ at Microwave frequency, static dielectric constant (ε0 and dielectric constant at infinite dilution (ε∞ at optical frequency have been determined. From the measured dielectric data, the relaxation time (t calculated using Higasi method and activation energies (∆Ft and ∆Fη have been determined. All the dielectric parameters that are vary with the substitutent change in benzyl alcohol andchain length of acrylic esters. Suggests that, the proton donating ability is varying with the substitution of benzyl alcohol and proton accepting ability is varying with the chain length of acrylic esters. The relaxation time and molar free energy activation of 1:1 molar ratio is greater than other higher molar ratios (i.e. 3:1, 2:1, 1:2, 1:3 confirm that the existence of most likely 1:1 complex formation between the studied systems and also complex formation formed between free hydroxyl group of substituted benzyl alcohols and carbonyl group of acrylic esters (MMA and EMA.

  20. The design of circuit for THz time domain spectroscopy system based on asynchronous optical sampling

    Science.gov (United States)

    Wang, Ruike; Zhang, Mile; Li, Yihan; He, Jingsuo; Zhang, Cunlin; Cui, Hailin

    2016-11-01

    Terahertz time domain spectroscopy system (THz-TDS) is the most commonly means of measuring terahertz time-domain spectroscopy. The time delay between the pump and probe laser is an important technology to realize THz time domain spectrum measurement. The translation platform with two mirrors and the mechanical structure is the popular means to adjust the optical path difference between the pump and probe laser to get the time delay of femtosecond pulse. Because of the limit of the mechanical structure and the phase-locked amplifier, this technique can't scan spectrum fast. In order to obtain high quality signal, a long time will be taken to scan spectrum. So a more rapid and convenient time delay technology is required to Instead of the machine translation platform and accomplish the Rapid spectral measurement. Asynchronous optical sampling technique is a way to get the time delay by producing a very small frequency difference between the repetition frequency of two femtosecond lasers. The scanner time will be reduced, because of there is no waste of time, due to mechanical inertia, not only by using the asynchronous optical sampling method to replace the mechanical structure without the influence of vibration. It will greatly increase the degree of integration by using the fiber femtosecond laser and highly integrated circuit to realize optical asynchronous sampling. To solve the problem above, a terahertz time-domain spectroscopy system based on asynchronous sampling is designed in this thesis. The system is based of two femtosecond laser whose repetition frequency is 100MHz.In order to realize asynchronous sampling, the control circuit of the two lasers is the most important. This thesis focuses on the researching, designing and experiment of this circuit. Firstly, the circuit is designed overall. Then the selection of the key device and the designing of the circuit principle is done by myself. Secondly, the test of the circuit to phase locked the master and

  1. A method of developing frequency encoded multi-bit optical data comparator using semiconductor optical amplifier

    Science.gov (United States)

    Garai, Sisir Kumar

    2011-02-01

    Optical data comparator is the part and parcel of arithmetic and logical unit of any optical data processor and it is working as a building block in a larger optical circuit, as an optical switch in all optical header processing and optical packet switching based all optical telecommunications system. In this article the author proposes a method of developing an all optical single bit comparator unit and subsequently extending the proposal to develop a n-bit comparator exploiting the nonlinear rotation of the state of polarization of the probe beam in semiconductor optical amplifier (SOA). Here the dataset to be compared are taken in frequency encoded/decoded form throughout the communication. The major advantages of frequency encoding over all other conventional techniques are that as the frequency of any signal is fundamental one so it can preserve its identity throughout the communication of optical signal and minimizes the probability of bit error problem. For frequency routing purpose optical add/drop multiplexer (ADM) is used which not only route the pump beams properly but also to amplify the pump beams efficiently. Switching speed of 'MZI-SOA switch' as well as SOA based switches are very fast with good on-off contrast ratio and as a result it is possible to obtain very fast action of optical data comparator.

  2. Frequency-domain and time-domain methods for feedback nonlinear systems and applications to chaos control

    Energy Technology Data Exchange (ETDEWEB)

    Duan Zhisheng [State Key Laboratory for Turbulence and Complex Systems and Department of Mechanics and Engineering Science, Peking University, Beijing 100871 (China)], E-mail: duanzs@pku.edu.cn; Wang Jinzhi; Yang Ying; Huang Lin [State Key Laboratory for Turbulence and Complex Systems and Department of Mechanics and Engineering Science, Peking University, Beijing 100871 (China)

    2009-04-30

    This paper surveys frequency-domain and time-domain methods for feedback nonlinear systems and their possible applications to chaos control, coupled systems and complex dynamical networks. The absolute stability of Lur'e systems with single equilibrium and global properties of a class of pendulum-like systems with multi-equilibria are discussed. Time-domain and frequency-domain criteria for the convergence of solutions are presented. Some latest results on analysis and control of nonlinear systems with multiple equilibria and applications to chaos control are reviewed. Finally, new chaotic oscillating phenomena are shown in a pendulum-like system and a new nonlinear system with an attraction/repulsion function.

  3. Time and Frequency Domain Identification and Analysis of a Gas Turbine Engine

    OpenAIRE

    Boaghe, O.M.; S. A. Billings; L. M. Li; Fleming, P J; Liu, J

    2000-01-01

    The NARMAX (Nonlinear Auto Regressive Moving Average model with eXogenous inputs) approach has been used to analyse the dynamics of a gas turbine engine. The fuel flow-shaft speed relationship is analysed by identifying both time and frequency domain models of the system. The frequency domain analysis is studied by mapping the discrete-time NARMAX models into the Generalised Frequency Response Functions (GFRF's) to reveal the nonlinear coupling between the various input spectral components an...

  4. Frequency comb metrology with an optical parametric oscillator.

    Science.gov (United States)

    Balskus, K; Schilt, S; Wittwer, V J; Brochard, P; Ploetzing, T; Jornod, N; McCracken, R A; Zhang, Z; Bartels, A; Reid, D T; Südmeyer, T

    2016-04-18

    We report on the first demonstration of absolute frequency comb metrology with an optical parametric oscillator (OPO) frequency comb. The synchronously-pumped OPO operated in the 1.5-µm spectral region and was referenced to an H-maser atomic clock. Using different techniques, we thoroughly characterized the frequency noise power spectral density (PSD) of the repetition rate frep, of the carrier-envelope offset frequency fCEO, and of an optical comb line νN. The comb mode optical linewidth at 1557 nm was determined to be ~70 kHz for an observation time of 1 s from the measured frequency noise PSD, and was limited by the stability of the microwave frequency standard available for the stabilization of the comb repetition rate. We achieved a tight lock of the carrier envelope offset frequency with only ~300 mrad residual integrated phase noise, which makes its contribution to the optical linewidth negligible. The OPO comb was used to measure the absolute optical frequency of a near-infrared laser whose second-harmonic component was locked to the F = 2→3 transition of the 87Rb D2 line at 780 nm, leading to a measured transition frequency of νRb = 384,228,115,346 ± 16 kHz. We performed the same measurement with a commercial fiber-laser comb operating in the 1.5-µm region. Both the OPO comb and the commercial fiber comb achieved similar performance. The measurement accuracy was limited by interferometric noise in the fibered setup of the Rb-stabilized laser.

  5. High-resolution retinal imaging using adaptive optics and Fourier-domain optical coherence tomography

    Science.gov (United States)

    Olivier, Scot S.; Werner, John S.; Zawadzki, Robert J.; Laut, Sophie P.; Jones, Steven M.

    2010-09-07

    This invention permits retinal images to be acquired at high speed and with unprecedented resolution in three dimensions (4.times.4.times.6 .mu.m). The instrument achieves high lateral resolution by using adaptive optics to correct optical aberrations of the human eye in real time. High axial resolution and high speed are made possible by the use of Fourier-domain optical coherence tomography. Using this system, we have demonstrated the ability to image microscopic blood vessels and the cone photoreceptor mosaic.

  6. Integrated structural and functional optical imaging combining spectral-domain optical coherence and multiphoton microscopy

    CERN Document Server

    Vinegoni, C; Luo, W; Marks, D L; Ralston, T; Tan, W

    2005-01-01

    An integrated microscope that combines different optical techniques for simultaneous imaging is demonstrated. The microscope enables spectral-domain optical coherence microscopy based on optical backscatter, and multi-photon microscopy for the detection of two-photon fluorescence and second harmonic generation signals. The unique configuration of this integrated microscope allows for the simultaneous acquisition of both anatomical (structural) and functional imaging information with particular emphasis for applications in the fields of tissue engineering and cell biology. In addition, the contemporary analysis of the spectroscopic features can enhance contrast by differentiating among different tissue components.

  7. ASIC-enabled High Resolution Optical Time Domain Reflectometer

    Science.gov (United States)

    Skendzic, Sandra

    Fiber optics has become the preferred technology in communication systems because of what it has to offer: high data transmission rates, immunity to electromagnetic interference, and lightweight, flexible cables. An optical time domain reflectometer (OTDR) provides a convenient method of locating and diagnosing faults (e.g. break in a fiber) along a fiber that can obstruct crucial optical pathways. Both the ability to resolve the precise location of the fault and distinguish between two discrete, closely spaced faults are figures of merit. This thesis presents an implementation of a high resolution OTDR through the use of a compact and programmable ASIC (application specific integrated circuit). The integration of many essential OTDR functions on a single chip is advantageous over existing commercial instruments because it enables small, lightweight packaging, and offers low power and cost efficiency. Furthermore, its compactness presents the option of placing multiple ASICs in parallel, which can conceivably ease the characterization of densely populated fiber optic networks. The OTDR ASIC consists of a tunable clock, pattern generator, precise timer, electrical receiver, and signal sampling circuit. During OTDR operation, the chip generates narrow electrical pulse, which can then be converted to optical format when coupled with an external laser diode driver. The ASIC also works with an external photodetector to measure the timing and amplitude of optical reflections in a fiber. It has a 1 cm sampling resolution, which allows for a 2 cm spatial resolution. While this OTDR ASIC has been previously demonstrated for multimode fiber fault diagnostics, this thesis focuses on extending its functionality to single mode fiber. To validate this novel approach to OTDR, this thesis is divided into five chapters: (1) introduction, (2) implementation, (3), performance of ASIC-based OTDR, (4) exploration in optical pre-amplification with a semiconductor optical amplifier, and

  8. Efficient microwave-induced optical frequency conversion

    CERN Document Server

    Kosachiov, D V

    1999-01-01

    Frequency conversion process is studied in a medium of atoms with a $\\Lambda$ configuration of levels, where transition between two lower states is driven by a microwave field. In this system, conversion efficiency can be very high by virtue of the effect of electromagnetically induced transparency (EIT). Depending on intensity of the microwave field, two regimes of EIT are realized: ''dark-state'' EIT for the weak field, and Autler-Townes-type EIT for the strong one. We study both cases via analytical and numerical solution and find optimum conditions for the conversion.

  9. Soliton generation from a multi-frequency optical signal

    Energy Technology Data Exchange (ETDEWEB)

    Panoiu, N-C [Department of Applied Physics and Applied Mathematics, Columbia University, New York, NY 10027 (United States); Mel' nikov, I V [Center for Research in Engineering and Applied Sciences, Morelos State Autonomous University, Av. Universidad 1001, 62210 Cuernavaca (Mexico); Mihalache, D [Department of Theoretical Physics, Institute of Atomic Physics, PO Box MG-6, Bucharest (Romania); Etrich, C [Institute of Solid State Theory and Theoretical Optics, Friedrich Schiller University Jena, Max-Wien-Platz 1, Jena, D-07743 (Germany); Lederer, F [Institute of Solid State Theory and Theoretical Optics, Friedrich Schiller University Jena, Max-Wien-Platz 1, Jena, D-07743 (Germany)

    2002-10-01

    We present a comprehensive analysis of the generation of optical solitons in a monomode optical fibre from a superposition of soliton-like optical pulses at different frequencies. It is demonstrated that the structure of the emerging optical field is highly dependent on the number of input channels, the inter-channel frequency separation, the time shift between the pulses belonging to adjacent channels, and the polarization of the pulses. Also, it is found that there exists a critical frequency separation above which wavelength-division multiplexing with solitons is feasible and that this critical frequency increases with the number of transmission channels. Moreover, for the case in which only two channels are considered, we analyse the propagation of the emerging two-soliton solutions in the presence of several perturbations important for optical networks: bandwidth-limited amplification, nonlinear amplification, and amplitude and phase modulation. Finally, the influence of the birefringence of the fibre on the structure of the emerging optical field is discussed. (review article)

  10. Nonlinear Dynamics of Photonics for Optical Signal Processing - Optical Frequency Conversion and Optical DSB-to-SSB Conversion

    Science.gov (United States)

    2015-09-17

    processing - optical frequency conversion and optical DSB -to-SSB conversion 5a. CONTRACT NUMBER FA2386-14-1-0006 5b. GRANT NUMBER Grant 134113...nonlinear dynamics of semiconductor lasers for certain optical signal processing functionalities, including optical DSB -to-SSB conversion, photonic...conversion and optical DSB -to-SSB conversion Performance Period May 30, 2014 ~ May 29, 2015 Principal Investigator Name: Sheng-Kwang Hwang Position

  11. Microwave Frequency Ferroelectric Domain Imaging of Deuterated Triglycine Sulfate Crystals

    Science.gov (United States)

    Steinhauer, David E.; Anlage, Steven M.

    2001-03-01

    We have used a near-field scanning microwave microscope(D. E. Steinhauer, C. P. Vlahacos, F. C. Wellstood, Steven M. Anlage, C. Canedy, R. Ramesh, A. Stanishevsky, and J. Melngailis, "Quantitative Imaging of Dielectric Permittivity and Tunability with a Near-Field Scanning Microwave Microscope," Rev. Sci. Instrum. 71), 2751-2758 (2000). to image domain structure and quantitatively measure dielectric permittivity and nonlinearity in ferroelectric crystals at 8.1 GHz with a spatial resolution of 1 μm. We imaged ferroelectric domains in periodically-poled LiNbO_3, BaTiO_3, and deuterated triglycine sulfate (DTGS) with a signal-to-noise ratio of 7. Measurement of the permittivity and nonlinearity of DTGS in the temperature range 300--400 K shows a peak at the Curie temperature, TC ≈ 340 K, as well as reasonable agreement with thermodynamic theory. In addition, the domain growth relaxation time shows a minimum near T_C. We observe coarsening of ferroelectric domains in DTGS after a temperature quench from 360 K to 330 K, and evaluate the structure factor.

  12. High Performance Small Optically Pumped Caesium Beam Frequency Standard

    Institute of Scientific and Technical Information of China (English)

    ZHANG Jian-Wei; YANG Dong-Hai

    2007-01-01

    An experiment of a high performance small optically pumped caesium (Cs) beam frequency standard is reported. An extended cavity diode laser works as the probing laser, of which the frequency is stabilized by the Zeeman modulation method. The running parameters of the frequency standard are dynamically optimized via digital servo electronics. The experimental setup improves the frequency stability up to 1.8 × 10-12 atτ= 1 s and about 1.0 × 10~13 at τ= 105 s (Allan deviation).

  13. Distributed hot-wire anemometry based on Brillouin optical time-domain analysis.

    Science.gov (United States)

    Wylie, Michael T V; Brown, Anthony W; Colpitts, Bruce G

    2012-07-02

    A distributed hot-wire anemometer based on Brillouin optical time-domain analysis is presented. The anemometer is created by passing a current through a stainless steel tube fibre bundle and monitoring Brillouin frequency changes in the presence of airflow. A wind tunnel is used to provide laminar airflow while the device response is calibrated against theoretical models. The sensitivity equation for this anemometer is derived and discussed. Airspeeds from 0 m/s to 10 m/s are examined, and the results show that a Brillouin scattering based distributed hot-wire anemometer is feasible.

  14. Femtosecond fibre laser stabilisation to an optical frequency standard using a KTP electro-optic crystal

    Energy Technology Data Exchange (ETDEWEB)

    Nyushkov, B N [Novosibirsk State University, Novosibirsk (Russian Federation); Pivtsov, V S; Koliada, N A [Institute of Laser Physics, Siberian Branch, Russian Academy of Sciences, Novosibirsk (Russian Federation); Kaplun, A B; Meshalkin, A B [S.S. Kutateladze Institute of Heat Physics, Siberian Division of the Russian Academy of Sciences, Novosibirsk (Russian Federation)

    2015-05-31

    A miniature intracavity KTP-based electro-optic phase modulator has been developed which can be used for effective stabilisation of an optical frequency comb of a femtosecond erbiumdoped fibre laser to an optical frequency standard. The use of such an electro-optic modulator (EOM) has made it possible to extend the working frequency band of a phase-locked loop system for laser stabilisation to several hundred kilohertz. We demonstrate that the KTP-based EOM is sufficiently sensitive even at a small optical length, which allows it to be readily integrated into cavities of femtosecond fibre lasers with high mode frequency spacings (over 100 MHz). (extreme light fields and their applications)

  15. Enabling Arbitrary Wavelength Optical Frequency Combs on Chip

    CERN Document Server

    Soltani, Mohammad; Maleki, Lute

    2015-01-01

    A necessary condition for generation of bright soliton Kerr frequency combs in microresonators is to achieve anomalous group velocity dispersion (GVD) for the resonator modes. This condition is hard to implement in visible as well as ultraviolet since the majority of optical materials are characterized with large normal GVD in these wavelength regions. We overcome this challenge by borrowing ideas from strongly dispersive coupled systems in solid state physics and optics. We show that photonic compound ring resonators can possess large anomalous GVD at any desirable wavelength, even if each individual resonator is characterized with normal GVD. Based on this concept we design a mode locked frequency comb with thin-film silicon nitride compound ring resonators in the vicinity of Rubidium D1 line (794.6nm) and propose to use this optical comb as a flywheel for chip-scale optical clocks.

  16. Reference-free, high-resolution measurement method of timing jitter spectra of optical frequency combs

    Science.gov (United States)

    Kwon, Dohyeon; Jeon, Chan-Gi; Shin, Junho; Heo, Myoung-Sun; Park, Sang Eon; Song, Youjian; Kim, Jungwon

    2017-01-01

    Timing jitter is one of the most important properties of femtosecond mode-locked lasers and optical frequency combs. Accurate measurement of timing jitter power spectral density (PSD) is a critical prerequisite for optimizing overall noise performance and further advancing comb applications both in the time and frequency domains. Commonly used jitter measurement methods require a reference mode-locked laser with timing jitter similar to or lower than that of the laser-under-test, which is a demanding requirement for many laser laboratories, and/or have limited measurement resolution. Here we show a high-resolution and reference-source-free measurement method of timing jitter spectra of optical frequency combs using an optical fibre delay line and optical carrier interference. The demonstrated method works well for both mode-locked oscillators and supercontinua, with 2 × 10−9 fs2/Hz (equivalent to −174 dBc/Hz at 10-GHz carrier frequency) measurement noise floor. The demonstrated method can serve as a simple and powerful characterization tool for timing jitter PSDs of various comb sources including mode-locked oscillators, supercontinua and recently emerging Kerr-frequency combs; the jitter measurement results enabled by our method will provide new insights for understanding and optimizing timing noise in such comb sources. PMID:28102352

  17. Wideband Radar Echo Frequency-domain Simulation and Analysis for High Speed Moving Targets

    Directory of Open Access Journals (Sweden)

    Ning Chao

    2014-04-01

    Full Text Available A frequency-domain method is proposed for wideband radar echo simulation of high-speed moving targets. Based on the physical process of electromagnetic waves observing a moving target, a frequency-domain echo model of wideband radar is constructed, and the block diagram of the radar echo simulation in frequency-domain is presented. Then, the impacts of radial velocity and slant range on the matching filtering of LFM radar are analyzed, and some quantitative conclusions on the shift and expansion of the radar profiles are obtained. Simulation results illustrate the correctness and efficiency of the proposed method.

  18. One-way quantum computing in the optical frequency comb.

    Science.gov (United States)

    Menicucci, Nicolas C; Flammia, Steven T; Pfister, Olivier

    2008-09-26

    One-way quantum computing allows any quantum algorithm to be implemented easily using just measurements. The difficult part is creating the universal resource, a cluster state, on which the measurements are made. We propose a scalable method that uses a single, multimode optical parametric oscillator (OPO). The method is very efficient and generates a continuous-variable cluster state, universal for quantum computation, with quantum information encoded in the quadratures of the optical frequency comb of the OPO.

  19. Optical frequency comb interference profilometry using compressive sensing.

    Science.gov (United States)

    Pham, Quang Duc; Hayasaki, Yoshio

    2013-08-12

    We describe a new optical system using an ultra-stable mode-locked frequency comb femtosecond laser and compressive sensing to measure an object's surface profile. The ultra-stable frequency comb laser was used to precisely measure an object with a large depth, over a wide dynamic range. The compressive sensing technique was able to obtain the spatial information of the object with two single-pixel fast photo-receivers, with no mechanical scanning and fewer measurements than the number of sampling points. An optical experiment was performed to verify the advantages of the proposed method.

  20. Weighted interframe averaging-based channel estimation for orthogonal frequency division multiplexing passive optical network

    Science.gov (United States)

    Lin, Bangjiang; Li, Yiwei; Zhang, Shihao; Tang, Xuan

    2015-10-01

    Weighted interframe averaging (WIFA)-based channel estimation (CE) is presented for orthogonal frequency division multiplexing passive optical network (OFDM-PON), in which the CE results of the adjacent frames are directly averaged to increase the estimation accuracy. The effectiveness of WIFA combined with conventional least square, intrasymbol frequency-domain averaging, and minimum mean square error, respectively, is demonstrated through 26.7-km standard single-mode fiber transmission. The experimental results show that the WIFA method with low complexity can significantly enhance transmission performance of OFDM-PON.

  1. Deep subwavelength nanometric image reconstruction using Fourier domain optical normalization

    Institute of Scientific and Technical Information of China (English)

    Jing Qin; Richard M Silver; Bryan M Barnes; Hui Zhou; Ronald G Dixson; Mark-Alexander Henn

    2016-01-01

    Quantitative optical measurements of deep subwavelength,three-dimensional (3D),nanometric structures with sensitivity to sub-nanometer details address a ubiquitous measurement challenge.A Fourier domain normalization approach is used in the Fourier optical imaging code to simulate the full 3D scattered light field of nominally 15 nm-sized structures,accurately replicating the light field as a function of the focus position.Using the full 3D light field,nanometer scale details such as a 2 nm thin conformal oxide and nanometer topography are rigorously fitted for features less than one-thirtiethof the wavelength in size.The densely packed structures are positioned nearly an order of magnitude closer than the conventional Rayleigh resolution limit and can be measured with sub-nanometer parametric uncertainties.This approach enables a practical measurement sensitivity to size variations of only a few atoms in size using a high-throughput optical configuration with broad application in measuring nanometric structures and nanoelectronic devices.

  2. High-Throughput, Protein-Targeted Biomolecular Detection Using Frequency-Domain Faraday Rotation Spectroscopy.

    Science.gov (United States)

    Murdock, Richard J; Putnam, Shawn A; Das, Soumen; Gupta, Ankur; Chase, Elyse D Z; Seal, Sudipta

    2017-01-16

    A clinically relevant magneto-optical technique (fd-FRS, frequency-domain Faraday rotation spectroscopy) for characterizing proteins using antibody-functionalized magnetic nanoparticles (MNPs) is demonstrated. This technique distinguishes between the Faraday rotation of the solvent, iron oxide core, and functionalization layers of polyethylene glycol polymers (spacer) and model antibody-antigen complexes (anti-BSA/BSA, bovine serum albumin). A detection sensitivity of ≈10 pg mL(-1) and broad detection range of 10 pg mL(-1) ≲ cBSA ≲ 100 µg mL(-1) are observed. Combining this technique with predictive analyte binding models quantifies (within an order of magnitude) the number of active binding sites on functionalized MNPs. Comparative enzyme-linked immunosorbent assay (ELISA) studies are conducted, reproducing the manufacturer advertised BSA ELISA detection limits from 1 ng mL(-1) ≲ cBSA ≲ 500 ng mL(-1) . In addition to the increased sensitivity, broader detection range, and similar specificity, fd-FRS can be conducted in less than ≈30 min, compared to ≈4 h with ELISA. Thus, fd-FRS is shown to be a sensitive optical technique with potential to become an efficient diagnostic in the chemical and biomolecular sciences.

  3. Spectral element method for elastic and acoustic waves in frequency domain

    Energy Technology Data Exchange (ETDEWEB)

    Shi, Linlin; Zhou, Yuanguo; Wang, Jia-Min; Zhuang, Mingwei [Institute of Electromagnetics and Acoustics, and Department of Electronic Science, Xiamen, 361005 (China); Liu, Na, E-mail: liuna@xmu.edu.cn [Institute of Electromagnetics and Acoustics, and Department of Electronic Science, Xiamen, 361005 (China); Liu, Qing Huo, E-mail: qhliu@duke.edu [Department of Electrical and Computer Engineering, Duke University, Durham, NC, 27708 (United States)

    2016-12-15

    Numerical techniques in time domain are widespread in seismic and acoustic modeling. In some applications, however, frequency-domain techniques can be advantageous over the time-domain approach when narrow band results are desired, especially if multiple sources can be handled more conveniently in the frequency domain. Moreover, the medium attenuation effects can be more accurately and conveniently modeled in the frequency domain. In this paper, we present a spectral-element method (SEM) in frequency domain to simulate elastic and acoustic waves in anisotropic, heterogeneous, and lossy media. The SEM is based upon the finite-element framework and has exponential convergence because of the use of GLL basis functions. The anisotropic perfectly matched layer is employed to truncate the boundary for unbounded problems. Compared with the conventional finite-element method, the number of unknowns in the SEM is significantly reduced, and higher order accuracy is obtained due to its spectral accuracy. To account for the acoustic-solid interaction, the domain decomposition method (DDM) based upon the discontinuous Galerkin spectral-element method is proposed. Numerical experiments show the proposed method can be an efficient alternative for accurate calculation of elastic and acoustic waves in frequency domain.

  4. Spectral element method for elastic and acoustic waves in frequency domain

    Science.gov (United States)

    Shi, Linlin; Zhou, Yuanguo; Wang, Jia-Min; Zhuang, Mingwei; Liu, Na; Liu, Qing Huo

    2016-12-01

    Numerical techniques in time domain are widespread in seismic and acoustic modeling. In some applications, however, frequency-domain techniques can be advantageous over the time-domain approach when narrow band results are desired, especially if multiple sources can be handled more conveniently in the frequency domain. Moreover, the medium attenuation effects can be more accurately and conveniently modeled in the frequency domain. In this paper, we present a spectral-element method (SEM) in frequency domain to simulate elastic and acoustic waves in anisotropic, heterogeneous, and lossy media. The SEM is based upon the finite-element framework and has exponential convergence because of the use of GLL basis functions. The anisotropic perfectly matched layer is employed to truncate the boundary for unbounded problems. Compared with the conventional finite-element method, the number of unknowns in the SEM is significantly reduced, and higher order accuracy is obtained due to its spectral accuracy. To account for the acoustic-solid interaction, the domain decomposition method (DDM) based upon the discontinuous Galerkin spectral-element method is proposed. Numerical experiments show the proposed method can be an efficient alternative for accurate calculation of elastic and acoustic waves in frequency domain.

  5. Mixed Discretization of the Time Domain MFIE at Low Frequencies

    KAUST Repository

    Ulku, Huseyin Arda

    2017-01-10

    Solution of the magnetic field integral equation (MFIE), which is obtained by the classical marching on-in-time (MOT) scheme, becomes inaccurate when the time step is large, i.e., under low-frequency excitation. It is shown here that the inaccuracy stems from the classical MOT scheme’s failure to predict the correct scaling of the current’s Helmholtz components for large time steps. A recently proposed mixed discretization strategy is used to alleviate the inaccuracy problem by restoring the correct scaling of the current’s Helmholtz components under low-frequency excitation.

  6. Spectral domain optical coherence tomography morphology in optic disc pit associated maculopathy

    Directory of Open Access Journals (Sweden)

    Janusz Michalewski

    2014-01-01

    Full Text Available Purpose: Our purpose was to study the clinical manifestation and course of optic pit maculopathy using Spectral Domain Optical Coherence Tomography (SD- OCT images. Materials and Methods: We used SD-OCT to examine 20 eyes of 19 patients with a macular detachment in combination with an optic. Results: We observed five different fovea appearances in regard to fluid localization. In five eyes, we recorded changes in the fluid distribution with SD-OCT. In 17/20 eyes, we noted a communication between the perineural and subretinal and/or intraretinal space at the margin of the optic disc. Conclusion: 3-dimensional SD-OCT (3D-SDOCT scans revealed a three-fold connection, between subretinal and intraretinal space, perineural space, and the vitreous cavity. Therefore, we suppose that intraretinal or subretinal fluid in optic pit maculopathy may have both a vitreous and cerebrospinal origin. A membrane, covering the optic nerve was noted in 14 cases. Even if it seems intact in some B-scans, it is not complete in others several micrometers apart. Additionally, we observed fluid accumulation below the margin of the optic disc and hyperreflective porous tissue in the optic disc excavation. Those findings do not influence the course of maculopathy.

  7. Optically transparent frequency selective surfaces on flexible thin plastic substrates

    Energy Technology Data Exchange (ETDEWEB)

    Dewani, Aliya A., E-mail: a.ashraf@griffith.edu.au; O’Keefe, Steven G.; Thiel, David V.; Galehdar, Amir [School Of Electrical Engineering, Griffith University, Brisbane, 4111 (Australia)

    2015-02-15

    A novel 2D simple low cost frequency selective surface was screen printed on thin (0.21 mm), flexible transparent plastic substrate (relative permittivity 3.2). It was designed, fabricated and tested in the frequency range 10-20 GHz. The plane wave transmission and reflection coefficients agreed with numerical modelling. The effective permittivity and thickness of the backing sheet has a significant effect on the frequency characteristics. The stop band frequency reduced from 15GHz (no backing) to 12.5GHz with polycarbonate. The plastic substrate thickness beyond 1.8mm has minimal effect on the resonant frequency. While the inner element spacing controls the stop-band frequency, the substrate thickness controls the bandwidth. The screen printing technique provided a simple, low cost FSS fabrication method to produce flexible, conformal, optically transparent and bio-degradable FSS structures which can find their use in electromagnetic shielding and filtering applications in radomes, reflector antennas, beam splitters and polarizers.

  8. Optically transparent frequency selective surfaces on flexible thin plastic substrates

    Science.gov (United States)

    Dewani, Aliya A.; O'Keefe, Steven G.; Thiel, David V.; Galehdar, Amir

    2015-02-01

    A novel 2D simple low cost frequency selective surface was screen printed on thin (0.21 mm), flexible transparent plastic substrate (relative permittivity 3.2). It was designed, fabricated and tested in the frequency range 10-20 GHz. The plane wave transmission and reflection coefficients agreed with numerical modelling. The effective permittivity and thickness of the backing sheet has a significant effect on the frequency characteristics. The stop band frequency reduced from 15GHz (no backing) to 12.5GHz with polycarbonate. The plastic substrate thickness beyond 1.8mm has minimal effect on the resonant frequency. While the inner element spacing controls the stop-band frequency, the substrate thickness controls the bandwidth. The screen printing technique provided a simple, low cost FSS fabrication method to produce flexible, conformal, optically transparent and bio-degradable FSS structures which can find their use in electromagnetic shielding and filtering applications in radomes, reflector antennas, beam splitters and polarizers.

  9. Finesse, Frequency domain INterferomEter Simulation SoftwarE

    CERN Document Server

    Freise, Andreas; Bond, Charlotte

    2013-01-01

    Finesse is a fast interferometer simulation program. For a given optical setup, it computes the light field amplitudes at every point in the interferometer assuming a steady state. To do so, the interferometer description is translated into a set of linear equations that are solved numerically. For convenience, a number of standard analyses can be performed automatically by the program, namely computing modulation-demodulation error signals, transfer functions, shot-noise-limited sensitivities, and beam shapes. Finesse can perform the analysis using the plane-wave approximation or Hermite-Gauss modes. The latter allows computation of the properties of optical systems like telescopes and the effects of mode matching and mirror angular positions.

  10. Plasmonic antenna array at optical frequency made by nanoapertures

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Z.J.; Huang, X.; Peng, R. W.; Wang, Z.; Gao, F.; Sun, W. H.; Wang, Q. J.; Wang, Mu

    2008-10-31

    We show here that the plasmonic array based on nanoapertures in ultrathin silver film radiates at optical frequency and behaves as an optical antenna array (OAA). The far-field radiation originates from the coherent superposition of plasmonic emissions on each bank of the aperture. The radiation of OAA presents a strong directivity, which depends on the in-plane rotation of aperture array, and on the polarization and incidence angle of the excitation light as well. We suggest that these features have potential applications in photovoltaics, light-emitting devices, and optical sensors.

  11. Ultra-high Frequency Linear Fiber Optic Systems

    CERN Document Server

    Lau, Kam

    2011-01-01

    This book provides an in-depth treatment of both linear fiber-optic systems and their key enabling devices. It presents a concise but rigorous treatment of the theory and practice of analog (linear) fiber-optics links and systems that constitute the foundation of Hybrid Fiber Coax infrastructure in present-day CATV distribution and cable modem Internet access. Emerging applications in remote fiber-optic feed for free-space millimeter wave enterprise campus networks are also described. Issues such as dispersion and interferometric noise are treated quantitatively, and means for mitigating them are explained. This broad but concise text will thus be invaluable not only to students of fiber-optics communication but also to practicing engineers. To the second edition of this book important new aspects of linear fiber-optic transmission technologies are added, such as high level system architectural issues, algorithms for deriving the optimal frequency assignment, directly modulated or externally modulated laser t...

  12. Frequency-domain generelaized singular peruturbation method for relative error model order reduction

    Institute of Scientific and Technical Information of China (English)

    Hamid Reza SHAKER

    2009-01-01

    A new mixed method for relative error model order reduction is proposed.In the proposed method the frequency domain balanced stochastic truncation method is improved by applying the generalized singular perturbation method to the frequency domain balanced system in the reduction procedure.The frequency domain balanced stochastic truncation method,which was proposed in [15] and [17] by the author,is based on two recently developed methods,namely frequency domain balanced truncation within a desired frequency bound and inner-outer factorization techniques.The proposed method in this paper is a carry over of the frequency-domain balanced stochastic truncation and is of interest for practical model order reduction because in this context it shows to keep the accuracy of the approximation as high as possible without sacrificing the computational efficiency and important system properties.It is shown that some important properties of the frequency domain stochastic balanced reduction technique are extended to the proposed reduction method by using the concept and properties of the reciprocal systems.Numerical results show the accuracy,simplicity and flexibility enhancement of the method.

  13. Frequency domain fluorescence lifetime microwell-plate platform for respirometry measurements

    Science.gov (United States)

    Chatni, M. R.; Yale, G.; Van Ryckeghem, A.; Porterfield, D. M.

    2010-04-01

    Traditionally micro-well plate based platforms used in biology utilize fluorescence intensity based methods to measure processes of biological relevance. However, fluorescence intensity measurements suffer from calibration drift due to a variety of factors. Photobleaching and self-quenching of the fluorescent dyes cause the intensity signal to drop over the lifetime of sensor immobilized inside the well. Variation in turbidity of the sample during the course of the measurement affects the measured fluorescence intensity. In comparison, fluorescence lifetime measurements are not significantly affected by these factors because fluorescence lifetime is a physico-chemical property of the fluorescent dye. Reliable and inexpensive frequency domain fluorescence lifetime instrumentation platforms are possible because the greater tolerance for optical alignment, and because they can be performed using inexpensive light sources such as LEDs. In this paper we report the development of a frequency domain fluorescence lifetime well-plate platform utilizing an oxygen sensitive transition-metal ligand complex fluorophore with a lifetime in the microsecond range. The fluorescence lifetime dye is incorporated in a polymer matrix and immobilized on the base of micro-well of a 60 well micro-well plate. Respiration measurements are performed in both aqueous and non-aqueous environment. Respirometry measurements were recorded from single Daphnia magna egg in hard water. Daphnia is an aquatic organism, important in environmental toxicology as a standard bioassay and early warning indicator for water quality monitoring. Also respirometry measurements were recorded from Tribolium castaneum eggs, which are common pests in the processed flour industry. These eggs were subjected to mitochondrial electron transport chain inhibitor such as potassium cyanide (KCN) and its effects on egg respiration were measured in real-time.

  14. Quantitative frequency-domain fluorescence spectroscopy in tissues and tissue-like media

    Science.gov (United States)

    Cerussi, Albert Edward

    1999-09-01

    In the never-ending quest for improved medical technology at lower cost, modern near-infrared optical spectroscopy offers the possibility of inexpensive technology for quantitative and non-invasive diagnoses. Hemoglobin is the dominant chromophore in the 700-900 nm spectral region and as such it allows for the optical assessment of hemoglobin concentration and tissue oxygenation by absorption spectroscopy. However, there are many other important physiologically relevant compounds or physiological states that cannot be effectively sensed via optical methods because of poor optical contrast. In such cases, contrast enhancements are required. Fluorescence spectroscopy is an attractive component of optical tissue spectroscopy. Exogenous fluorophores, as well as some endogenous ones, may furnish the desperately needed sensitivity and specificity that is lacking in near-infrared optical tissue spectroscopy. The main focus of this thesis was to investigate the generation and propagation of fluorescence photons inside tissues and tissue-like media (i.e., scattering dominated media). The standard concepts of fluorescence spectroscopy have been incorporated into a diffusion-based picture that is sometimes referred to as photon migration. The novelty of this work lies in the successful quantitative recovery of fluorescence lifetimes, absolute fluorescence quantum yields, fluorophore concentrations, emission spectra, and both scattering and absorption coefficients at the emission wavelength from a tissue-like medium. All of these parameters are sensitive to the fluorophore local environment and hence are indicators of the tissue's physiological state. One application demonstrating the capabilities of frequency-domain lifetime spectroscopy in tissue-like media is a study of the binding of ethidium bromide to bovine leukocytes in fresh milk. Ethidium bromide is a fluorescent dye that is commonly used to label DNA, and hence visualize chromosomes in cells. The lifetime of

  15. The application of finite element method to forward and inverse seismic problems in frequency domain

    Energy Technology Data Exchange (ETDEWEB)

    Shaoyou, J.; Xiangheng, J.; Shizhe, X.

    1987-04-01

    Unstable result is obtained when the boundary problem of wave equation is solved using finite element method in time domain. However, when the boundary problem of wave equation is solved by finite element method in frequency domain, not only the unstablity can be avoided but also computation is speeded up because of using FFT. The procedure for solving the boundary problem using finite element method in frequency domain is as follows: 1. the wave equation is transformed into Helmholtz equation by making one-dimensional Fourier transform with respect to time; 2. Helmholtz equation is solved using finite element method in frequency domain; 3. the obtained result is returned to time domain by making inverse Fourier transform. Both forward and inverse seismic problems can be solved by this method.

  16. Efficiency Improvement of the frequency-domain BEM for Rapid transient elastodynamic analysis

    CERN Document Server

    Xiao, Jinyou; Wen, Lihua

    2012-01-01

    The frequency-domain fast boundary element method (BEM) combined with the exponential window technique leads to an efficient yet simple method for elastodynamic analysis. In this paper, the efficiency of this method is further enhanced by three strategies. Firstly, we propose to use exponential window with large damping parameter to improve the conditioning of the BEM matrices. Secondly, the frequency domain windowing technique is introduced to alleviate the severe Gibbs oscillations in time-domain responses caused by large damping parameters. Thirdly, a solution extrapolation scheme is applied to obtain better initial guesses for solving the sequential linear systems in the frequency domain. Numerical results of three typical examples with the problem size up to 0.7 million unknowns clearly show that the first and third strategies can significantly reduce the computational time. The second strategy can effectively eliminate the Gibbs oscillations and result in accurate time-domain responses.

  17. Single snapshot multiple frequency modulated imaging of subsurface optical properties of turbid media with structured light

    Science.gov (United States)

    Xu, M.; Cao, Zili; Lin, Weihao; Chen, Xinlin; Zheng, Longfei; Zeng, Bixin

    2016-12-01

    We report a novel demodulation method that enables single snapshot wide field imaging of optical properties of turbid media in the Spatial Frequency Domain (SFD). This Single Snapshot Multiple frequency Demodulation (SSMD) method makes use of the orthogonality of harmonic functions to extract the modulation transfer function (MTF) at multiple modulation frequencies simultaneously from a single structured-illuminated image at once. The orientation, frequency, and amplitude of each modulation can be set arbitrarily subject to the limitation of the implementation device. We first validate and compare SSMD to the existing demodulation methods by numerical simulations. The performance of SSMD is then demonstrated with experiments on both tissue mimicking phantoms and in vivo for recovering optical properties by comparing to the standard three-phase demodulation approach. The results show that SSMD increases significantly the data acquisition speed and reduces motion artefacts. SSMD exhibits excellent noise suppression in imaging as well at the rate proportional to the square root of the number of pixels contained in its kernel. SSMD is ideal in the implementation of a real-time spatial frequency domain imaging platform and will open up SFDI for vast applications in imaging and monitoring dynamic turbid medium and processes.

  18. Single snapshot multiple frequency modulated imaging of subsurface optical properties of turbid media with structured light

    Directory of Open Access Journals (Sweden)

    M. Xu

    2016-12-01

    Full Text Available We report a novel demodulation method that enables single snapshot wide field imaging of optical properties of turbid media in the Spatial Frequency Domain (SFD. This Single Snapshot Multiple frequency Demodulation (SSMD method makes use of the orthogonality of harmonic functions to extract the modulation transfer function (MTF at multiple modulation frequencies simultaneously from a single structured-illuminated image at once. The orientation, frequency, and amplitude of each modulation can be set arbitrarily subject to the limitation of the implementation device. We first validate and compare SSMD to the existing demodulation methods by numerical simulations. The performance of SSMD is then demonstrated with experiments on both tissue mimicking phantoms and in vivo for recovering optical properties by comparing to the standard three-phase demodulation approach. The results show that SSMD increases significantly the data acquisition speed and reduces motion artefacts. SSMD exhibits excellent noise suppression in imaging as well at the rate proportional to the square root of the number of pixels contained in its kernel. SSMD is ideal in the implementation of a real-time spatial frequency domain imaging platform and will open up SFDI for vast applications in imaging and monitoring dynamic turbid medium and processes.

  19. Optical Frequency Upconversion Technique for Transmission of Wireless MIMO-Type Signals over Optical Fiber

    Directory of Open Access Journals (Sweden)

    R. Q. Shaddad

    2014-01-01

    Full Text Available The optical fiber is well adapted to pass multiple wireless signals having different carrier frequencies by using radio-over-fiber (ROF technique. However, multiple wireless signals which have the same carrier frequency cannot propagate over a single optical fiber, such as wireless multi-input multi-output (MIMO signals feeding multiple antennas in the fiber wireless (FiWi system. A novel optical frequency upconversion (OFU technique is proposed to solve this problem. In this paper, the novel OFU approach is used to transmit three wireless MIMO signals over a 20 km standard single mode fiber (SMF. The OFU technique exploits one optical source to produce multiple wavelengths by delivering it to a LiNbO3 external optical modulator. The wireless MIMO signals are then modulated by LiNbO3 optical intensity modulators separately using the generated optical carriers from the OFU process. These modulators use the optical single-sideband with carrier (OSSB+C modulation scheme to optimize the system performance against the fiber dispersion effect. Each wireless MIMO signal is with a 2.4 GHz or 5 GHz carrier frequency, 1 Gb/s data rate, and 16-quadrature amplitude modulation (QAM. The crosstalk between the wireless MIMO signals is highly suppressed, since each wireless MIMO signal is carried on a specific optical wavelength.

  20. Optical frequency upconversion technique for transmission of wireless MIMO-type signals over optical fiber.

    Science.gov (United States)

    Shaddad, R Q; Mohammad, A B; Al-Gailani, S A; Al-Hetar, A M

    2014-01-01

    The optical fiber is well adapted to pass multiple wireless signals having different carrier frequencies by using radio-over-fiber (ROF) technique. However, multiple wireless signals which have the same carrier frequency cannot propagate over a single optical fiber, such as wireless multi-input multi-output (MIMO) signals feeding multiple antennas in the fiber wireless (FiWi) system. A novel optical frequency upconversion (OFU) technique is proposed to solve this problem. In this paper, the novel OFU approach is used to transmit three wireless MIMO signals over a 20 km standard single mode fiber (SMF). The OFU technique exploits one optical source to produce multiple wavelengths by delivering it to a LiNbO3 external optical modulator. The wireless MIMO signals are then modulated by LiNbO3 optical intensity modulators separately using the generated optical carriers from the OFU process. These modulators use the optical single-sideband with carrier (OSSB+C) modulation scheme to optimize the system performance against the fiber dispersion effect. Each wireless MIMO signal is with a 2.4 GHz or 5 GHz carrier frequency, 1 Gb/s data rate, and 16-quadrature amplitude modulation (QAM). The crosstalk between the wireless MIMO signals is highly suppressed, since each wireless MIMO signal is carried on a specific optical wavelength.

  1. Frequency domain analysis and synthesis of lumped parameter systems using nonlinear least squares techniques

    Science.gov (United States)

    Hays, J. R.

    1969-01-01

    Lumped parametric system models are simplified and computationally advantageous in the frequency domain of linear systems. Nonlinear least squares computer program finds the least square best estimate for any number of parameters in an arbitrarily complicated model.

  2. Method of shifting and fixing optical frequency of an optical resonator, and optical resonator made by same

    Science.gov (United States)

    Savchenkov, Anatoliy A. (Inventor); Strekalov, Dmitry V. (Inventor); Maleki, Lute (Inventor); Matsko, Andrey B. (Inventor); Iltchenko, Vladimir S. (Inventor); Martin, Jan M. (Inventor)

    2010-01-01

    A method of shifting and fixing an optical frequency of an optical resonator to a desired optical frequency, and an optical resonator made by such a method are provided. The method includes providing an optical resonator having a surface and a refractive index, and obtaining a coating composition having a predetermined concentration of a substance and having a refractive index that is substantially similar to the refractive index of the optical resonator. The coating composition inherently possesses a thickness when it is applied as a coating. The method further includes determining a coating ratio for the surface of the optical resonator and applying the coating composition onto a portion of the surface of the optical resonator based upon the determined coating ratio.

  3. Analysis of BER of OFDM in Optical Domain with Different Modulation Techniques

    Directory of Open Access Journals (Sweden)

    A. R. Gifty Arul Marin

    2013-01-01

    Full Text Available In OFDM system, the subcarrier frequencies are chosen so that the subcarriers are orthogonal to each other, meaning that cross talk between the sub channels is eliminated. Priority of OFDM system is given to minimizing the interference or crosstalk among the channels and symbols comprising the data stream. The primary advantage of OFDM is its ability to cope with severe channel conditions like attenuation of high frequencies, narrowband interference and frequency selective fading due to multipath. The existing OFDM systems were modelled based on frequency domain using various modulation techniques in AWGN channel. This is a research analysis to calculate the efficient BER of the OFDM system in the optical domain using BPSK and QPSK modulation techniques. This project can be used for high speed applications requiring more band width. Finally, performance comparison of BPSK and QPSK modulation schemes in OFDM system and the calculation of BER (Bit Error Rate using these modulation techniques is to be done. The entire OFDM system is implemented using SIMULINK tool in MATLAB

  4. Microresonator-Based Optical Frequency Combs: A Time Domain Perspective

    Science.gov (United States)

    2016-04-19

    May - Nov 1998; Nov 1998. 4. TITLE. Enter title and subtitle with volume number and part number, if applicable. On classified documents, enter...accordance with security classification regulations, e.g. U, C, S, etc. If this form contains classified information, stamp classification level on...Consistent with the goals of this program, we have now realized microresonators at 75, 37.5, and 25 GHz free spectral range (FSR) and have observed comb

  5. Squeezing Alters Frequency Tuning of WGM Optical Resonator

    Science.gov (United States)

    Mohageg, Makan; Maleki, Lute

    2010-01-01

    Mechanical squeezing has been found to alter the frequency tuning of a whispering-gallery-mode (WGM) optical resonator that has an elliptical shape and is made of lithium niobate. It may be possible to exploit this effect to design reconfigurable optical filters for optical communications and for scientific experiments involving quantum electrodynamics. Some background information is prerequisite to a meaningful description of the squeezing-induced alteration of frequency tuning: The spectrum of a WGM resonator is represented by a comblike plot of intensity versus frequency. Each peak of the comblike plot corresponds to an electromagnetic mode represented by an integer mode number, and the modes are grouped into sets represented by integer mode indices. Because lithium niobate is an electro-optically active material, the WGM resonator can be tuned (that is, the resonance frequencies can be shifted) by applying a suitable bias potential. The frequency shift of each mode is quantified by a tuning rate defined as the ratio between the frequency shift and the applied potential. In the absence of squeezing, all modes exhibit the same tuning rate. This concludes the background information. It has been demonstrated experimentally that when the resonator is squeezed along part of either of its two principal axes, tuning rates differ among the groups of modes represented by different indices (see figure). The differences in tuning rates could be utilized to configure the resonance spectrum to obtain a desired effect; for example, through a combination of squeezing and electrical biasing, two resonances represented by different mode indices could be set at a specified frequency difference something that could not be done through electrical biasing alone.

  6. The Capability of Time- And Frequency-domain Algorithms for Bistatic SAR Processing

    OpenAIRE

    Vu, Viet; Sjögren, Thomas; Pettersson, Mats

    2013-01-01

    The paper presents a study of the capability of time- And frequency-domain algorithms for bistatic SAR processing. Two typical algorithms, Bistatic Fast Backprojection (BiFBP) and Bistatic Range Doppler (BiRDA), which are both available for general bistatic geometry, are selected as the examples of time- And frequency-domain algorithms in this study. Their capability is evaluated based on some criteria such as processing time required by the algorithms to reconstruct SAR images from bistatic ...

  7. BER Performance of Frequency Domain Differential Demodulation OFDM in Flat Fading Channel

    Institute of Scientific and Technical Information of China (English)

    SONG Lijun; TANG Youxi; LI Shaoqian; HUANG Shunji

    2003-01-01

    A closed form expression for the bit error rate (BER) performance of frequency domain differential demodulation(FDDD) for orthogonal frequency division multiplexing system in flat fading channel is derived. The performance is evaluated by computer simulation and compared with the time domain differential demodulation(TDDD). The results indicate that the performance of FDDD is better than that of TDDD, and the lower band of BER in the former is lower than that of the latter.

  8. Optimizing optical Bragg scattering for single-photon frequency conversion

    CERN Document Server

    Lefrancois, Simon; Eggleton, Benjamin J

    2014-01-01

    We develop a systematic theory for optimising single-photon frequency conversion using optical Bragg scattering. The efficiency and phase-matching conditions for the desired Bragg scattering conversion as well as spurious scattering and modulation instability are identified. We find that third-order dispersion can suppress unwanted processes, while dispersion above the fourth order limits the maximum conversion efficiency. We apply the optimisation conditions to frequency conversion in highly nonlinear fiber, silicon nitride waveguides and silicon nanowires. Efficient conversion is confirmed using full numerical simulations. These design rules will assist the development of efficient quantum frequency conversion between multicolour single photon sources for integration in complex quantum networks.

  9. Volumetric (3D) compressive sensing spectral domain optical coherence tomography.

    Science.gov (United States)

    Xu, Daguang; Huang, Yong; Kang, Jin U

    2014-11-01

    In this work, we proposed a novel three-dimensional compressive sensing (CS) approach for spectral domain optical coherence tomography (SD OCT) volumetric image acquisition and reconstruction. Instead of taking a spectral volume whose size is the same as that of the volumetric image, our method uses a sub set of the original spectral volume that is under-sampled in all three dimensions, which reduces the amount of spectral measurements to less than 20% of that required by the Shan-non/Nyquist theory. The 3D image is recovered from the under-sampled spectral data dimension-by-dimension using the proposed three-step CS reconstruction strategy. Experimental results show that our method can significantly reduce the sampling rate required for a volumetric SD OCT image while preserving the image quality.

  10. Crack detection using multimode fiber optical time domain reflectometry

    Science.gov (United States)

    Wanser, Keith H.; Voss, Karl F.

    1994-09-01

    Results of measurements of longitudinal and transverse crack growth using multimode fiber optical time domain reflectometry are presented. Crack detection thresholds less than 0.1 millimeter are readily achieved with OTDR. A sensor package design has been developed to provide controllable directional response characteristics. In particular, a method to eliminate the orientation angle problem and yield omnidirectional sensor response characteristics has been discovered. Results are reported on a novel all-fiber sensor capable of sensing 10 micrometers crack displacements while surviving and sensing 150% strains and displacements of 6 mm. Transmission measurements of the sensor using white light are also reported. The method is suitable for distributed sensing applications covering large areas of structures and adaptable to response enhancements required for real time structural monitoring at rates on the order of hundreds of Hertz. Applications include bridges, buildings, main-steam pipelines, and offshore platforms.

  11. Profile and Determinants of Retinal Optical Intensity in Normal Eyes with Spectral Domain Optical Coherence Tomography.

    Directory of Open Access Journals (Sweden)

    Binyao Chen

    Full Text Available To investigate the profile and determinants of retinal optical intensity in normal subjects using 3D spectral domain optical coherence tomography (SD OCT.A total of 231 eyes from 231 healthy subjects ranging in age from 18 to 80 years were included and underwent a 3D OCT scan. Forty-four eyes were randomly chosen to be scanned by two operators for reproducibility analysis. Distribution of optical intensity of each layer and regions specified by the Early Treatment of Diabetic Retinopathy Study (ETDRS were investigated by analyzing the OCT raw data with our automatic graph-based algorithm. Univariate and multivariate analyses were performed between retinal optical intensity and sex, age, height, weight, spherical equivalent (SE, axial length, image quality, disc area and rim/disc area ratio (R/D area ratio.For optical intensity measurements, the intraclass correlation coefficient of each layer ranged from 0.815 to 0.941, indicating good reproducibility. Optical intensity was lowest in the central area of retinal nerve fiber layer, ganglion cell layer, inner plexiform layer, inner nuclear layer, outer plexiform layer and photoreceptor layer, except for the retinal pigment epithelium (RPE. Optical intensity was positively correlated with image quality in all retinal layers (0.5530.05. There was no relationship between retinal optical intensity and sex, height, weight, SE, axial length, disc area and R/D area ratio.There was a specific pattern of distribution of retinal optical intensity in different regions. The optical intensity was affected by image quality and age. Image quality can be used as a reference for normalization. The effect of age needs to be taken into consideration when using OCT for diagnosis.

  12. Optimal light harvesting structures at optical and infrared frequencies

    CERN Document Server

    Villate-Guío, F; García-Vidal, F J; Martín-Moreno, L; de León-Pérez, F

    2012-01-01

    One-dimensional light harvesting structures with a realistic geometry nano-patterned on an opaque metallic film are optimized to render high transmission efficiencies at optical and infrared frequencies. Simple design rules are developed for the particular case of a slit-groove array with a given number of grooves that are symmetrically distributed with respect to a central slit. These rules take advantage of the hybridization of Fabry-Perot modes in the slit and surface modes of the corrugated metal surface. Same design rules apply for optical and infrared frequencies. The parameter space of the groove array is also examined with a conjugate gradient optimization algorithm that used as a seed the geometries optimized following physical intuition. Both uniform and nonuniform groove arrays are considered. The largest transmission enhancement, with respect to a uniform array, is obtained for a chirped groove profile. Such enhancement is a function of the wavelength. It decreases from 39% in the optical part of ...

  13. Frequency Comparison of Two High-Accuracy Al+ Optical Clocks

    CERN Document Server

    Chou, C -W; Koelemeij, J C J; Wineland, D J; Rosenband, T

    2009-01-01

    We have constructed an optical clock with a fractional frequency inaccuracy of 8.6e-18, based on quantum logic spectroscopy of an Al+ ion. A simultaneously trapped Mg+ ion serves to sympathetically laser-cool the Al+ ion and detect its quantum state. The frequency of the 1S0->3P0 clock transition is compared to that of a previously constructed Al+ optical clock with a statistical measurement uncertainty of 7.0e-18. The two clocks exhibit a relative stability of 2.8e-15/ sqrt(tau), and a fractional frequency difference of -1.8e-17, consistent with the accuracy limit of the older clock.

  14. Frequency Comparison of Two High-Accuracy Al+ Optical Clocks

    Science.gov (United States)

    Chou, C. W.; Hume, D. B.; Koelemeij, J. C. J.; Wineland, D. J.; Rosenband, T.

    2010-02-01

    We have constructed an optical clock with a fractional frequency inaccuracy of 8.6×10-18, based on quantum logic spectroscopy of an Al+ ion. A simultaneously trapped Mg+ ion serves to sympathetically laser cool the Al+ ion and detect its quantum state. The frequency of the S01↔P03 clock transition is compared to that of a previously constructed Al+ optical clock with a statistical measurement uncertainty of 7.0×10-18. The two clocks exhibit a relative stability of 2.8×10-15τ-1/2, and a fractional frequency difference of -1.8×10-17, consistent with the accuracy limit of the older clock.

  15. Micro--structured crystalline resonators for optical frequency comb generation

    CERN Document Server

    Grudinin, Ivan S

    2014-01-01

    Optical frequency combs have recently been demonstrated in micro--resonators through nonlinear Kerr processes. Investigations in the past few years provided better understanding of micro--combs and showed that spectral span and mode locking are governed by cavity spectrum and dispersion. While various cavities provide unique advantages, dispersion engineering has been reported only for planar waveguides. In this Letter, we report a resonator design that combines dispersion control, mode crossing free spectrum, and ultra--high quality factor. We experimentally show that as the dispersion of a MgF2 resonator is flattened, the comb span increases reaching 700 nm with as low as 60 mW pump power at 1560 nm wavelength, corresponding to nearly 2000 lines separated by 46 GHz. The new resonator design may enable efficient low repetition rate coherent octave spanning frequency combs without the need for external broadening, ideal for applications in optical frequency synthesis, metrology, spectroscopy, and communicatio...

  16. Depth Compensated Spectral Domain Optical Coherence Tomography via Digital Compensation

    CERN Document Server

    Boroomand, Ameneh; Shafiee, Mohammad Javad; Bizheva, Kostadinka; Wong, Alexander

    2015-01-01

    Spectral Domain Optical Coherence Tomography (SD-OCT) is a well-known imaging modality which allows for \\textit{in-vivo} visualization of the morphology of different biological tissues at cellular level resolutions. The overall SD-OCT imaging quality in terms of axial resolution and Signal-to-Noise Ratio (SNR) degrades with imaging depth, while the lateral resolution degrades with distance from the focal plane. This image quality degradation is due both to the design of the SD-OCT imaging system and the optical properties of the imaged object. Here, we present a novel Depth Compensated SD-OCT (DC-OCT) system that integrates a Depth Compensating Digital Signal Processing (DC-DSP) module to improve the overall imaging quality via digital compensation. The designed DC-DSP module can be integrated to any SD-OCT system and is able to simultaneously compensate for the depth-dependent loss of axial and lateral resolutions, depth-varying SNR, as well as sidelobe artifact for improved imaging quality. The integrated D...

  17. Detection of optic nerve lesions in optic neuritis using frequency-selective fat-saturation sequences

    Energy Technology Data Exchange (ETDEWEB)

    Miller, D.H. (NMR Research Unit, National Hospital for Neurology and Neurosurgery, London (United Kingdom)); MacManus, D.G. (NMR Research Unit, National Hospital for Neurology and Neurosurgery, London (United Kingdom)); Bartlett, P.A. (St. Mary' s Hospital, London (United Kingdom)); Kapoor, R. (NMR Research Unit, National Hospital for Neurology and Neurosurgery, London (United Kingdom)); Morrissey, S.P. (NMR Research Unit, National Hospital for Neurology and Neurosurgery, London (United Kingdom)); Moseley, I.F. (NMR Research Unit, National Hospital for Neurology and Neurosurgery, London (United Kingdom))

    1993-02-01

    MRI was performed on seven patients with acute optic neuritis, using two sequences which suppress the signal from orbital fat: frequency-selective fat-saturation and inversion recovery with a short inversion time. Lesions were seen on both sequences in all the symptomatic optic nerves studied. (orig.)

  18. Optimal Frequency-Domain System Realization with Weighting

    Science.gov (United States)

    Juang, Jer-Nan; Maghami, Peiman G.

    1999-01-01

    Several approaches are presented to identify an experimental system model directly from frequency response data. The formulation uses a matrix-fraction description as the model structure. Frequency weighting such as exponential weighting is introduced to solve a weighted least-squares problem to obtain the coefficient matrices for the matrix-fraction description. A multi-variable state-space model can then be formed using the coefficient matrices of the matrix-fraction description. Three different approaches are introduced to fine-tune the model using nonlinear programming methods to minimize the desired cost function. The first method uses an eigenvalue assignment technique to reassign a subset of system poles to improve the identified model. The second method deals with the model in the real Schur or modal form, reassigns a subset of system poles, and adjusts the columns (rows) of the input (output) influence matrix using a nonlinear optimizer. The third method also optimizes a subset of poles, but the input and output influence matrices are refined at every optimization step through least-squares procedures.

  19. Wide field visualization of retinal and choroidal microstructure in vivo using frequency domain OCT at 1060 nm with up to 47000 lines/s

    Science.gov (United States)

    Hermann, Boris; Esmaeelpour, M.; Povazay, Boris; Hofer, Bernd; Bounaparte, F.; Sheen, Nick; North, Rachel; Drexler, Wolfgang

    2009-02-01

    We present in vivo frequency domain optical coherence tomography of the human retina and choroid in the 1060 nm water transmission window with 72 nm optical bandwidth (choroidal vasculature without the need of contrast agents, the choroidal-scleral interface as well as the first scleral layer, the absorbing lamina fusca sclerae. Furthermore the choroidal thickness was quantified in 30 healthy subjects and correlated with axial eye length. First results indicate an decrease in choroidal thickness with increasing axial eye length.

  20. Dual-frequency Brillouin fiber laser for optical generation of tunable low-noise radio frequency/microwave frequency.

    Science.gov (United States)

    Geng, Jihong; Staines, Sean; Jiang, Shibin

    2008-01-01

    We demonstrate a new approach, i.e., a cw dual-frequency Brillouin fiber laser pumped by two independent single-frequency Er-doped fiber lasers, for the generation of tunable low-noise rf/microwave optical signals. Its inherent features of both linewidth narrowing effect in a Brillouin fiber cavity and common mode noise cancellation between two laser modes sharing a common cavity allow us to achieve high frequency stability without using a supercavity. Beat frequency of the dual-frequency Brillouin fiber laser can be tuned from tens of megahertz up to 100 GHz by thermally tuning the wavelengths of the two pump lasers with tuning sensitivity of approximately 1.4 GHz/ degrees C. Allan variance measurements show the beat signals have the hertz-level frequency stability.

  1. Transport processes in mixed conducting oxides: combining time domain experiments and frequency domain analysis

    NARCIS (Netherlands)

    Boukamp, Bernard A.; Otter, den Matthijs W.; Bouwmeester, Henny J.M.

    2004-01-01

    The conductivity relaxation (CR) method is often used for measuring the surface transfer rate, Ktr, and the bulk diffusion coefficient, $$\\tilde{D},$$ for oxygen transport in mixed conducting oxides (MIECs). The time domain analysis of the obtained CR response is rather complex and is based on lsquo

  2. Time-Domain Optical Fourier Transformation for OTDM-DWDM and DWDM-OTDM Conversion

    DEFF Research Database (Denmark)

    Mulvad, Hans Christian Hansen; Palushani, Evarist; Galili, Michael

    2011-01-01

    Applications of time-domain optical Fourier transformation (OFT) in ultra-high-speed optical time-division multiplexed systems (OTDM) are reviewed, with emphasis on the recent demonstrations of OFT-based conversion between the OTDM and DWDM formats.......Applications of time-domain optical Fourier transformation (OFT) in ultra-high-speed optical time-division multiplexed systems (OTDM) are reviewed, with emphasis on the recent demonstrations of OFT-based conversion between the OTDM and DWDM formats....

  3. Broadband photonic microwave phase shifter based on controlling two RF modulation sidebands via a Fourier-domain optical processor.

    Science.gov (United States)

    Yang, J; Chan, E H W; Wang, X; Feng, X; Guan, B

    2015-05-04

    An all-optical photonic microwave phase shifter that can realize a continuous 360° phase shift over a wide frequency range is presented. It is based on the new concept of controlling the amplitude and phase of the two RF modulation sidebands via a Fourier-domain optical processor. The operating frequency range of the phase shifter is largely increased compared to the previously reported Fourier-domain optical processor based phase shifter that uses only one RF modulation sideband. This is due to the extension of the lower RF operating frequency by designing the amplitude and phase of one of the RF modulation sidebands while the other sideband is designed to realize the required RF signal phase shift. The two-sideband amplitude-and-phase-control based photonic microwave phase shifter has a simple structure as it only requires a single laser source, a phase modulator, a Fourier-domain optical processor and a single photodetector. Investigation on the bandwidth limitation problem in the conventional Fourier-domain optical processor based phase shifter is presented. Comparisons between the measured phase shifter output RF amplitude and phase responses with theory, which show excellent agreement, are also presented for the first time. Experimental results demonstrate the full -180° to + 180° phase shift with little RF signal amplitude variation of less than 3 dB and with a phase deviation of less than 4° over a 7.5 GHz to 26.5 GHz frequency range, and the phase shifter exhibits a long term stable performance.

  4. Plasmon nanoparticle superlattices as optical-frequency magnetic metamaterials.

    Science.gov (United States)

    Alaeian, Hadiseh; Dionne, Jennifer A

    2012-07-02

    Nanocrystal superlattices have emerged as a new platform for bottom-up metamaterial design, but their optical properties are largely unknown. Here, we investigate their emergent optical properties using a generalized semi-analytic, full-field solver based on rigorous coupled wave analysis. Attention is given to superlattices composed of noble metal and dielectric nanoparticles in unary and binary arrays. By varying the nanoparticle size, shape, separation, and lattice geometry, we demonstrate the broad tunability of superlattice optical properties. Superlattices composed of spherical or octahedral nanoparticles in cubic and AB(2) arrays exhibit magnetic permeabilities tunable between 0.2 and 1.7, despite having non-magnetic constituents. The retrieved optical parameters are nearly polarization and angle-independent over a broad range of incident angles. Accordingly, nanocrystal superlattices behave as isotropic bulk metamaterials. Their tunable permittivities, permeabilities, and emergent magnetism may enable new, bottom-up metamaterials and negative index materials at visible frequencies.

  5. Intense harmonics generation with customized photon frequency and optical vortex

    Science.gov (United States)

    Zhang, Xiaomei; Shen, Baifei; Shi, Yin; Zhang, Lingang; Ji, Liangliang; Wang, Xiaofeng; Xu, Zhizhan; Tajima, Toshiki

    2016-08-01

    An optical vortex with orbital angular momentum (OAM) enriches the light and matter interaction process, and helps reveal unexpected information in relativistic nonlinear optics. A scheme is proposed for the first time to explore the origin of photons in the generated harmonics, and produce relativistic intense harmonics with expected frequency and an optical vortex. When two counter-propagating Laguerre-Gaussian laser pulses impinge on a solid thin foil and interact with each other, the contribution of each input pulse in producing harmonics can be distinguished with the help of angular momentum conservation of photons, which is almost impossible for harmonic generation without an optical vortex. The generation of tunable, intense vortex harmonics with different photon topological charge is predicted based on the theoretical analysis and three-dimensional particle-in-cell simulations. Inheriting the properties of OAM and harmonics, the obtained intense vortex beam can be applied in a wide range of fields, including atom or molecule control and manipulation.

  6. Using mechanics to convert between microwave and optical frequencies

    Science.gov (United States)

    Vainsencher, A.; Satzinger, K. J.; Peairs, G. A.; Cleland, A. N.

    2016-03-01

    We demonstrate unique piezoelectric optomechanical devices able to coherently transfer microwave electrical signals to modulated optical signals, and vice versa, transferring modulated optical signals to microwave electrical signals. This coherent bilateral transfer, demonstrated most recently in a single device design, holds promise for the eventual demonstration of coherent transfer in the quantum domain. The basis of design for the devices with which this was accomplished is an optomechanical crystal that supports co-located optical and mechanical resonant modes, coupled to one other via moving boundary (index of refraction) modulation, either induced by motion from energy in the mechanical mode, or by optical pressure due to energy in the optical mode. The basis for coupling microwave mechanical motion to microwave electrical signals is via the use of a piezoelectric material for the entire device, where transduction itself is accomplished using metal transducers remote from the optomechanical structure. This remote design minimizes the lossy interaction of any optical signals with the metal electrode structures, but introduces the need to couple the electromechanical transducer to the optomechanical transducer via itinerant phonons, which presents a new challenge.

  7. Frequency domain transfer function identification using the computer program SYSFIT

    Energy Technology Data Exchange (ETDEWEB)

    Trudnowski, D.J.

    1992-12-01

    Because the primary application of SYSFIT for BPA involves studying power system dynamics, this investigation was geared toward simulating the effects that might be encountered in studying electromechanical oscillations in power systems. Although the intended focus of this work is power system oscillations, the studies are sufficiently genetic that the results can be applied to many types of oscillatory systems with closely-spaced modes. In general, there are two possible ways of solving the optimization problem. One is to use a least-squares optimization function and to write the system in such a form that the problem becomes one of linear least-squares. The solution can then be obtained using a standard least-squares technique. The other method involves using a search method to obtain the optimal model. This method allows considerably more freedom in forming the optimization function and model, but it requires an initial guess of the system parameters. SYSFIT employs this second approach. Detailed investigations were conducted into three main areas: (1) fitting to exact frequency response data of a linear system; (2) fitting to the discrete Fourier transformation of noisy data; and (3) fitting to multi-path systems. The first area consisted of investigating the effects of alternative optimization cost function options; using different optimization search methods; incorrect model order, missing response data; closely-spaced poles; and closely-spaced pole-zero pairs. Within the second area, different noise colorations and levels were studied. In the third area, methods were investigated for improving fitting results by incorporating more than one system path. The following is a list of guidelines and properties developed from the study for fitting a transfer function to the frequency response of a system using optimization search methods.

  8. Frequency-domain equalization for OFDMA-based multiuser MIMO systems with improper modulation schemes

    Science.gov (United States)

    Xiao, Pei; Lin, Zihuai; Fagan, Anthony; Cowan, Colin; Vucetic, Branka; Wu, Yi

    2011-12-01

    In this paper, we propose a novel transceiver structure for orthogonal frequency division multiple access-based uplink multiuser multiple-input multiple-output systems. The numerical results show that the proposed frequency-domain equalization schemes significantly outperform conventional linear minimum mean square error-based equalizers in terms of bit error rate performance with moderate increase in computational complexity.

  9. Comparing a mercury optical lattice clock with microwave and optical frequency standards

    CERN Document Server

    Tyumenev, R; Bilicki, S; Bookjans, E; Targat, R Le; Lodewyck, J; Nicolodi, D; Coq, Y Le; Abgrall, M; Guéna, J; De Sarlo, L; Bize, S

    2016-01-01

    In this paper we report the evaluation of an optical lattice clock based on neutral mercury down to a relative uncertainty of $1.7\\times 10^{-16}$. Comparing this characterized frequency standard to a Cs atomic fountain we determine the absolute frequency of the $^1S_0 \\rightarrow \\phantom{}^3P_0$ transition of $^{199}$Hg as $\

  10. Statistics and frequency-domain moveout for multiple-taper receiver functions

    Science.gov (United States)

    Park, J.; Levin, V.

    2016-10-01

    The multiple-taper correlation (MTC) algorithm for the estimation of teleseismic receiver functions (RFs) has desirable statistical properties. This paper presents several adaptations to the MTC algorithm that exploit its frequency-domain uncertainty estimates to generate stable RFs that include moveout corrections for deeper interfaces. Narrow-band frequency averaging implicit in spectral cross-correlation restricts the MTC-based RF estimates to resolve Ps converted phases only at short delay times, appropriate to the upper 100 km of Earth's lithosphere. The Ps conversions from deeper interfaces can be reconstructed by the MTC algorithm in two ways. Event cross-correlation computes a cross-correlation of single-taper spectrum estimates for a cluster of events rather than for a set of eigenspectrum estimates of a single P coda. To extend the reach of the algorithm, pre-stack moveout corrections in the frequency domain preserves the formal uncertainties of the RF estimates, which are used to weight RF stacks. Moving-window migration retains the multiple-taper approach, but cross-correlates the P-polarized motion with time-delayed SH and SV motion to focus on a Ps phase of interest. The frequency-domain uncertainties of bin-averaged RFs do not translate directly into the time domain. A jackknife over data records in each bin stack offers uncertainty estimates in the time domain while preserving uncertainty weighting in the frequency-domain RF stack.

  11. Distributed Fiber Optical Sensing of Oxygen with Optical Time Domain Reflectometry

    Directory of Open Access Journals (Sweden)

    Elmar Schmälzlin

    2013-05-01

    Full Text Available In many biological and environmental applications spatially resolved sensing of molecular oxygen is desirable. A powerful tool for distributed measurements is optical time domain reflectometry (OTDR which is often used in the field of telecommunications. We combine this technique with a novel optical oxygen sensor dye, triangular-[4] phenylene (TP, immobilized in a polymer matrix. The TP luminescence decay time is 86 ns. The short decay time of the sensor dye is suitable to achieve a spatial resolution of some meters. In this paper we present the development and characterization of a reflectometer in the UV range of the electromagnetic spectrum as well as optical oxygen sensing with different fiber arrangements.

  12. MULTILOOP PI CONTROLLER FOR ACHIEVING SIMULTANEOUS TIME AND FREQUENCY DOMAIN SPECIFICATIONS

    Directory of Open Access Journals (Sweden)

    M. SENTHILKUMAR

    2015-08-01

    Full Text Available Most of the controllers in control system are designed to satisfy either time domain or frequency domain specifications. This work presents the computation of a multiloop PI controller for achieving time and frequency domain specifications simultaneously. The desired time and frequency domain measures are to be specified initially to the design. To obtain the desired value of the performance measures the graphical relationship between the PI controller and the performance criteria is given. Thus by using graphical method a set of PI controller parameters to meet the desired performance measures are obtained in an effective and simpler way. The coupled tank has become a classic design of control engineering for multivariable process. The proposed control strategy has been implemented in the same coupled tank process and validated through simulation studies.

  13. Time and frequency domain models for multiaxial fatigue life estimation under random loading

    Directory of Open Access Journals (Sweden)

    Andrea Carpinteri

    2015-07-01

    Full Text Available Engineering structures and components are often subjected to random fatigue loading produced, for example, by wind turbulences, marine waves and vibrations. The methods available in the literature for fatigue assessment under random loading are formulated in time domain or, alternatively, in frequency domain. The former methods require the knowledge of the loading time history, and a large number of experimental tests/numerical simulations is needed to obtain statistically reliable results. The latter methods are generally more advantageous with respect to the time domain ones, allowing a rapid fatigue damage evaluation. In the present paper, a multiaxial criterion formulated in the frequency-domain is presented to estimate the fatigue lives of smooth metallic structures subjected to combined bending and torsion random loading. A comparison in terms of fatigue life prediction by employing a time domain methods, previously proposed by the authors, is also performed.

  14. Modeling of earthquake ground motion in the frequency domain

    Science.gov (United States)

    Thrainsson, Hjortur

    In recent years, the utilization of time histories of earthquake ground motion has grown considerably in the design and analysis of civil structures. It is very unlikely, however, that recordings of earthquake ground motion will be available for all sites and conditions of interest. Hence, there is a need for efficient methods for the simulation and spatial interpolation of earthquake ground motion. In addition to providing estimates of the ground motion at a site using data from adjacent recording stations, spatially interpolated ground motions can also be used in design and analysis of long-span structures, such as bridges and pipelines, where differential movement is important. The objective of this research is to develop a methodology for rapid generation of horizontal earthquake ground motion at any site for a given region, based on readily available source, path and site characteristics, or (sparse) recordings. The research includes two main topics: (i) the simulation of earthquake ground motion at a given site, and (ii) the spatial interpolation of earthquake ground motion. In topic (i), models are developed to simulate acceleration time histories using the inverse discrete Fourier transform. The Fourier phase differences, defined as the difference in phase angle between adjacent frequency components, are simulated conditional on the Fourier amplitude. Uniformly processed recordings from recent California earthquakes are used to validate the simulation models, as well as to develop prediction formulas for the model parameters. The models developed in this research provide rapid simulation of earthquake ground motion over a wide range of magnitudes and distances, but they are not intended to replace more robust geophysical models. In topic (ii), a model is developed in which Fourier amplitudes and Fourier phase angles are interpolated separately. A simple dispersion relationship is included in the phase angle interpolation. The accuracy of the interpolation

  15. Time-domain analysis of frequency dependent inertial wave forces on cylinders

    DEFF Research Database (Denmark)

    Krenk, Steen

    2013-01-01

    -number, and the relevant range of waves shorter than about six times the diameter typically corresponds to deep water waves. This permits a universal non-dimensional frequency representation, that is converted to rational form to provide the relevant filter equation. Simple time-domain simulations demonstrate...... a simple time-domain procedure for the inertial force, in which the frequency dependence is represented via a simple explicit time filter on the wave particle acceleration or velocity. The frequency dependence of the inertia coefficient is known analytically as a function of the wave...

  16. Generation of frequency-chirped optical pulses with felix

    Energy Technology Data Exchange (ETDEWEB)

    Knippels, G.M.H.; Meer, A.F.G. van der; Mols, R.F.X.A.M. [FOM-Institute for Plasma Physics, Nieuwegein (Netherlands)] [and others

    1995-12-31

    Frequency-chirped optical pulses have been produced in the picosecond regime by varying the energy of the electron beam on a microsecond time scale. These pulses were then compressed close to their bandwidth limit by an external pulse compressor. The amount of chirp can be controlled by varying the sweep rate on the electron beam energy and by cavity desynchronisation. To examine the generated chirp we used the following diagnostics: a pulse compressor, a crossed beam autocorrelator, a multichannel electron spectrometer and multichannel optical spectrometer. The compressor is build entirely using reflective optics to permit broad band operation. The autocorrelator is currently operating from 6 {mu}m to 30 {mu}m with one single crystal. It has been used to measure pulses as short as 500 fs. All diagnostics are evacuated to prevent pulse shape distortion or pulse lengthening caused by absorption in ambient water vapour. Pulse length measurements and optical spectra will be presented for different electron beam sweep rates, showing the presence of a frequency chirp. Results on the compression of the optical pulses to their bandwidth limit are given for different electron sweep rates. More experimental results showing the dependence of the amount of chirp on cavity desynchronisation will be presented.

  17. Optical frequency divider with division uncertainty at the 10^(-21) level

    CERN Document Server

    Yao, Yuan; Yu, Hongfu; Bi, Zhiyi; Ma, Longsheng

    2016-01-01

    Optical clocks with unprecedented accuracy of 10^(-18) will lead to innovations in many research areas. All the applications of optical clocks rely on the ability of precisely converting the frequency from one optical clock to another, or particularly to the frequencies in the fiber telecom band for long-distance transmission. Here, we report a low-noise, high precision optical frequency divider. It can realize accurate optical frequency conversion as well as enable precise measurement of optical frequency ratios. By comparing against the frequency ratio between the fundamental and the second harmonic of a 1064 nm laser rather than a second similar system, the optical frequency divider is demonstrated to have a frequency division instability of 6e-19 at 1 s and a fractional frequency division uncertainty of 1.4e-21, nearly three orders of magnitude better than the most accurate optical clocks. It allows optical clocks to be accessible to many precision measurement applications.

  18. Optical to microwave clock frequency ratios with a nearly continuous strontium optical lattice clock

    CERN Document Server

    Lodewyck, Jérôme; Bookjans, Eva; Robyr, Jean-Luc; Shi, Chunyan; Vallet, Grégoire; Targat, Rodolphe Le; Nicolodi, Daniele; Coq, Yann Le; Guéna, Jocelyne; Abgrall, Michel; Rosenbusch, Peter; Bize, Sébastien

    2016-01-01

    Optical lattice clocks are at the forefront of frequency metrology. Both the instability and systematic uncertainty of these clocks have been reported to be two orders of magnitude smaller than the best microwave clocks. For this reason, a redefinition of the SI second based on optical clocks seems possible in the near future. However, the operation of optical lattice clocks has not yet reached the reliability that microwave clocks have achieved so far. In this paper, we report on the operation of a strontium optical lattice clock that spans several weeks, with more than 80% uptime. We make use of this long integration time to demonstrate a reproducible measurement of frequency ratios between the strontium clock transition and microwave Cs primary and Rb secondary frequency standards.

  19. Fatigue of wind turbines in the frequency domain

    Energy Technology Data Exchange (ETDEWEB)

    Bishop, N.W.M. [Univ. College London (United Kingdom)

    1996-09-01

    Fatigue damage is traditionally determined from time signals of loading, usually in the form of stress or strain. However, there are three design scenarios when a spectral form of loading is more appropriate. In this case the loading is defined in terms of its magnitude at different frequencies in the form of a Power Spectral Density (PSD) plot. First, the measurement engineer recording responses from in-service components or structures may be interested in PSD`s because they are a efficient way of defining a random stress or strain time history. Secondly, the test engineer assessing the reliability of prototypes may be interested in spectral tools because such an approach allows the structural condition of the component to be monitored by continuous inspection of the system transfer function. However, the most important benefit of working with PSD`s is relevant to the structural analysis or designer because of the more sophisticated analysis options with which they can be use. For all three of these design scenarios the fatigue designer is presented with a PSD of stress or strain with which to perform his fatigue calculation. There is therefore a requirement for a reliable, accurate and robust spectral fatigue design tool. Such a tool allows the designer to estimate the rainflow range content and hence content and hence fatigue damage from the PSD. (EG)

  20. Digital Frequency Domain Multiplexer for mm-Wavelength Telescopes

    Energy Technology Data Exchange (ETDEWEB)

    Spieler, Helmuth G; Dobbs, Matt; Bissonnette, Eric; Spieler, Helmuth G.

    2007-07-23

    An FPGA based digital signal processing (DSP) system for biasing and reading out multiplexed bolometric detectors for mm-wavelength telescopes is presented. This readout system is being deployed for balloon-borne and ground based cosmology experiments with the primary goal of measuring the signature of inflation with the Cosmic Microwave Background Radiation. The system consists of analog superconducting electronics running at 250 mK and 4 K, coupled to digital room temperature backend electronics described here. The digital electronics perform the real time functionality with DSP algorithms implemented in firmware. A soft embedded processor provides all of the slow housekeeping control and communications. Each board in the system synthesizes multi-frequency combs of 8 to 32 carriers in the MHz band to bias the detectors. After the carriers have been modulated with the sky-signal by the detectors, the same boards digitize the comb directly. The carriers are mixed down to base-band and low pass filtered. The signal bandwidth of 0.050Hz-100 Hz places extreme requirements on stability and requires powerful filtering techniques to recover the sky-signal from the MHz carriers.

  1. Waveform inversion for acoustic VTI media in frequency domain

    KAUST Repository

    Wu, Zedong

    2016-09-06

    Reflected waveform inversion (RWI) provides a method to reduce the nonlinearity of the standard full waveform inversion (FWI) by inverting for the background model using a single scattered wavefield from an inverted perturbation. However, current RWI methods are mostly based on isotropic media assumption. We extend the idea of the combining inversion for the background model and perturbations to address transversely isotropic with a vertical axis of symmetry (VTI) media taking into consideration of the optimal parameter sensitivity information. As a result, we apply Born modeling corresponding to perturbations in only for the variable e to derive the relative reflected waveform inversion formulation. To reduce the number of parameters, we assume the background part of η = ε and work with a single variable to describe the anisotropic part of the wave propagation. Thus, the optimization variables are the horizontal velocity v, η = ε and the e perturbation. Application to the anisotropic version of Marmousi model with a single frequency of 2.5 Hz shows that this method can converge to the accurate result starting from a linearly increasing isotropic initial velocity. Application to a real dataset demonstrates the versatility of the approach.

  2. Dynamic Analysis of Cable Roofs Under Transient Wind:A Comparison Between Time Domain and Frequency Domain Approaches

    Institute of Scientific and Technical Information of China (English)

    S.Ali Ghafari Oskoei; Ghyslaine McClure

    2008-01-01

    At present,high.speed computing capabilities and advanced nonlinear dynamic finite element procedures enable detailed dynamic analysis of cable structures.Although deterministic approaches require considerable analysis time and effort in relation to modeling,running,and data processing,they seem to be the only alternative to obtain high accuracy.Detailed dynamic analysis of cable roof networks is sophisticated and requires advanced modeling expertise.This paper presents a comparison between detailed nonlinear dynamic analysis and a simplified frequency domain approach to estimate the maximum probable response of weakly nonlinear cable roofs.The approach can be considered as alternative to detailed time-domain analysis in the preliminary design phase,or can be used to validate results obtained from more elaborated numerical models.The proposed method is illustrated with two examples of cable net roofs that were also analysed in the time domain.

  3. Comparison of Frequency-Domain Array Methods for Studying Earthquake Rupture Process

    Science.gov (United States)

    Sheng, Y.; Yin, J.; Yao, H.

    2014-12-01

    Seismic array methods, in both time- and frequency- domains, have been widely used to study the rupture process and energy radiation of earthquakes. With better spatial resolution, the high-resolution frequency-domain methods, such as Multiple Signal Classification (MUSIC) (Schimdt, 1986; Meng et al., 2011) and the recently developed Compressive Sensing (CS) technique (Yao et al., 2011, 2013), are revealing new features of earthquake rupture processes. We have performed various tests on the methods of MUSIC, CS, minimum-variance distortionless response (MVDR) Beamforming and conventional Beamforming in order to better understand the advantages and features of these methods for studying earthquake rupture processes. We use the ricker wavelet to synthesize seismograms and use these frequency-domain techniques to relocate the synthetic sources we set, for instance, two sources separated in space but, their waveforms completely overlapping in the time domain. We also test the effects of the sliding window scheme on the recovery of a series of input sources, in particular, some artifacts that are caused by the sliding window scheme. Based on our tests, we find that CS, which is developed from the theory of sparsity inversion, has relatively high spatial resolution than the other frequency-domain methods and has better performance at lower frequencies. In high-frequency bands, MUSIC, as well as MVDR Beamforming, is more stable, especially in the multi-source situation. Meanwhile, CS tends to produce more artifacts when data have poor signal-to-noise ratio. Although these techniques can distinctly improve the spatial resolution, they still produce some artifacts along with the sliding of the time window. Furthermore, we propose a new method, which combines both the time-domain and frequency-domain techniques, to suppress these artifacts and obtain more reliable earthquake rupture images. Finally, we apply this new technique to study the 2013 Okhotsk deep mega earthquake

  4. Time domain acoustic contrast control implementation of sound zones for low-frequency input signals

    DEFF Research Database (Denmark)

    Schellekens, Daan H. M.; Møller, Martin Bo; Olsen, Martin

    2016-01-01

    -of-the-art time domain broadband acoustic contrast control (BACC) methods are designed for anechoic environments. These methods are not able to realize a flat frequency response in a limited frequency range within a reverberant environment. Sound field control in a limited frequency range is a requirement...... to accommodate the effective working range of the loudspeakers. In this paper, a new BACC method is proposed which results in an implementation realizing a flat frequency response in the target zone. This method is applied in a bandlimited low-frequency scenario where the loudspeaker layout surrounds two...

  5. High-resolution 640 Gbit/s clock recovery using time-domain optical Fourier transformation and narrowband optical filter

    DEFF Research Database (Denmark)

    Mulvad, Hans Christian Hansen; Guan, P.; Kasai, K.

    2010-01-01

    We demonstrate pre-scaled 40 GHz clock recovery from 640 Gbit/s optical time-division-multiplexed data using LiNbO$_3$ modulators, based on time-domain optical Fourier transformation and optical filtering. The clock recovery is used in a 640 Gbit/s error-free transmission over 300 km....

  6. Channel estimation in space and frequency domain for MIMO-OFDM systems

    Institute of Scientific and Technical Information of China (English)

    PAN Pei-sheng; ZHENG Bao-yu

    2009-01-01

    Multiple-input multiple-output (MIMO) systems can be combined with orthogonal frequency division multiplexing (OFDM) systems to improve the capacity and quality of wireless communications. In this article, a channel estimation technique in both space and frequency domain for MIMO-OFDM systems is proposed. It is shown that the proposed scheme with space-frequency pilot tones achieve optimal minimum mean square error (MMSE) channel estimation. Simulation results indicate that the proposed method achieves good performance.

  7. Frequency-dependent optical steering from subwavelength plasmonic structures.

    Science.gov (United States)

    Djalalian-Assl, A; Gómez, D E; Roberts, A; Davis, T J

    2012-10-15

    We show theoretically and with numerical simulations that the direction of the in-plane scattering from a subwavelength optical antenna system can be controlled by the frequency of the incident light. This optical steering effect does not rely on propagation phase shifts or diffraction but arises from phase shifts in the localized surface plasmon modes of the antenna. An analytical model is developed to optimize the parameters for the configuration, showing good agreement with a rigorous numerical simulation. The simulation predicts a 25° angular shift in the direction of the light scattered from two gold nanorods for a wavelength change of 12 nm.

  8. Optical sum-frequency generation in whispering gallery mode resonators

    CERN Document Server

    Strekalov, Dmitry V; Huang, Yu-Ping; Kumar, Prem

    2013-01-01

    We demonstrate sum-frequency generation in a nonlinear whispering gallery mode resonator between a telecom wavelength and the Rb D2 line, achieved through natural phase matching. Due to the strong optical field confinement and ultra high Q of the cavity, we achieve a 1000-fold enhancement in the conversion efficiency compared to existing waveguide-based devices. The experimental data are in agreement with the nonlinear dynamics and phase matching theory in the spherical geometry employed. The experimental and theoretical results point to a new platform to manipulate the color and quantum states of light waves toward applications such as atomic memory based quantum networking and logic operations with optical signals.

  9. Optical Kerr Frequency Comb Generation in Overmoded Resonators

    CERN Document Server

    Matsko, A B; Liang, W; Ilchenko, V S; Seidel, D; Maleki, L

    2012-01-01

    We show that scattering-based interaction among nearly degenerate optical modes is the key factor in low threshold generation of Kerr frequency combs in nonlinear optical resonators possessing small group velocity dispersion (GVD). The mode interaction is capable of producing drastic change in the local GVD, resulting in either a significant reduction or increase of the oscillation threshold. It is also responsible for the majority of observed combs in resonators characterized with large normal GVD. We present results of our numerical simulations as well as supporting experimental data.

  10. Systematic Shifts for Ytterbium-ion Optical Frequency Standards

    CERN Document Server

    Batra, N; Gupta, A Sen; Singh, Sukhjit; Arora, Amisha; Arora, Bindiya

    2014-01-01

    The projected systematic uncertainties of single trapped Ytterbium-ion optical frequency standards are estimated for the quadrupole and octupole transitions which are at wavelengths 435.5 nm and 467 nm, respectively. Finite temperature of the ion and its interaction with the external fields introduce drift in the measured frequency compared to its absolute value. Frequency shifts due to electric quadrupole moment, induced polarization and excess micromotion of the ion depend on electric fields, which are estimated in this article. Geometry of the trap electrodes also result in unwanted electric fields which have been considered in our calculation. Magnetic field induced shift and Stark shifts due to electro-magnetic radiation at a surrounding temperature are also estimated. At CSIR-NPL, we are developing a frequency standard based on the octupole transition for which the systematic uncertainties are an order of magnitude smaller than that using the quadrupole transition, as described here.

  11. Colloidal superlattices for unnaturally high-index metamaterials at broadband optical frequencies

    CERN Document Server

    Lee, Seungwoo

    2015-01-01

    The recent advance in the assembly of metallic nanoparticles (NPs) has enabled sophisticated engineering of unprecedented light-matter interaction at the optical domain. In this work, I expand the design flexibility of NP optical metamaterial to push the upper limit of accessible refractive index to the unnaturally high regime. The precise control over the geometrical parameters of NP superlattice monolayer conferred the dramatic increase in electric resonance and related effective permittivity far beyond the naturally accessible regime. Simultaneously, effective permeability, another key factor to achieving high refractive index, was effectively suppressed by reducing the thickness of NPs. By establishing this design rule, I have achieved unnaturally high refractive index (15.7 at the electric resonance and 7.3 at the quasi-static limit) at broadband optical frequencies (100 THz ~ 300 THz). I also combined this NP metamaterial with graphene to electrically control the high refractive index over the broad opt...

  12. Coherent coupling between radio frequency, optical, and acoustic waves in piezo-optomechanical circuits.

    Science.gov (United States)

    Balram, Krishna C; Davanço, Marcelo I; Song, Jin Dong; Srinivasan, Kartik

    2016-05-01

    Optomechanical cavities have been studied for applications ranging from sensing to quantum information science. Here, we develop a platform for nanoscale cavity optomechanical circuits in which optomechanical cavities supporting co-localized 1550 nm photons and 2.4 GHz phonons are combined with photonic and phononic waveguides. Working in GaAs facilitates manipulation of the localized mechanical mode either with a radio frequency (RF) field through the piezo-electric effect, which produces acoustic waves that are routed and coupled to the optomechanical cavity by phononic crystal waveguides, or optically through the strong photoelastic effect. Along with mechanical state preparation and sensitive readout, we use this to demonstrate an acoustic wave interference effect, similar to atomic coherent population trapping, in which RF-driven coherent mechanical motion is cancelled by optically-driven motion. Manipulating cavity optomechanical systems with equal facility through both photonic and phononic channels enables new architectures for signal transduction between the optical, electrical, and mechanical domains.

  13. Nonlinear optics at low powers: Alternative mechanism of on-chip optical frequency comb generation

    Science.gov (United States)

    Rogov, Andrei S.; Narimanov, Evgenii E.

    2016-12-01

    Nonlinear optical effects provide a natural way of light manipulation and interaction and form the foundation of applied photonics, from high-speed signal processing and telecommunication to ultrahigh-bandwidth interconnects and information processing. However, relatively weak nonlinear response at optical frequencies calls for operation at high optical powers or boosting efficiency of nonlinear parametric processes by enhancing local-field intensity with high-quality-factor resonators near cavity resonance, resulting in reduced operational bandwidth and increased loss due to multiphoton absorption. We present an alternative to this conventional approach, with strong nonlinear optical effects at low local intensities, based on period-doubling bifurcations near nonlinear cavity antiresonance and apply it to low-power optical frequency comb generation in a silicon chip.

  14. A Modified Normalization Technique for Frequency-Domain Full Waveform Inversion

    Science.gov (United States)

    Hwang, J.; Jeong, G.; Min, D. J.; KIM, S.; Heo, J. Y.

    2016-12-01

    Full waveform inversion (FWI) is a technique to estimate subsurface material properties minimizing the misfit function built with residuals between field and modeled data. To achieve computational efficiency, FWI has been performed in the frequency domain by carrying out modeling in the frequency domain, whereas observed data (time-series data) are Fourier-transformed.One of the main drawbacks of seismic FWI is that it easily gets stuck in local minima because of lacking of low-frequency data. To compensate for this limitation, damped wavefields are used, as in the Laplace-domain waveform inversion. Using damped wavefield in FWI plays a role in generating low-frequency components and help recover long-wavelength structures. With these newly generated low-frequency components, we propose a modified frequency-normalization technique, which has an effect of boosting contribution of low-frequency components to model parameter update.In this study, we introduce the modified frequency-normalization technique which effectively amplifies low-frequency components of damped wavefields. Our method is demonstrated for synthetic data for the SEG/EAGE salt model. AcknowledgementsThis work was supported by the Korea Institute of Energy Technology Evaluation and Planning(KETEP) and the Ministry of Trade, Industry & Energy(MOTIE) of the Republic of Korea (No. 20168510030830) and by the Dual Use Technology Program, granted financial resource from the Ministry of Trade, Industry & Energy, Republic of Korea.

  15. Frequency translation of light waves by propagation around an optical ring circuit containing a frequency shifter: I. Experiment.

    Science.gov (United States)

    Shimizu, K; Horiguchi, T; Koyamada, Y

    1993-11-20

    A technique for the external frequency translation of light waves is reported. The technique permits the stepwise sweeping of an optical frequency over a wide range with high linearity with respect to time. The frequency translator is composed of an optical pulse modulator and an optical ring circuit containing an acousto-optic frequency shifter and an optical amplifier. The pulse launched into the ring circuit undergoes a constant frequency shift for each circulation around the circuit and the frequency can be translated to a considerable degree from that of the original input pulse. We report a stepwise frequency translation over approximately 68 GHz for a 1.5-µm light wave with a strictly constant frequency-sweep rate and an approximately constant intensity.

  16. a Decade-Spanning High-Resolution Asynchronous Optical Sampling Based Terahertz Time-Domain Spectrometer

    Science.gov (United States)

    Good, Jacob T.; Holland, Daniel; Finneran, Ian A.; Carroll, Brandon; Allodi, Marco A.; Blake, Geoffrey

    2015-06-01

    High-resolution ASynchronous OPtical Sampling (ASOPS) is a technique that substantially improves the combined frequency resolution and bandwidth of ASOPS based TeraHertz Time-Domain Spectroscopy (THz-TDS) systems. We employ two mode-locked femtosecond Ti:Sapphire oscillators with repetition frequencies of 80 MHz operating at a fixed repetition frequency offset of 100 Hz. This offset lock is maintained by a Phase-Locked Loop (PLL) operating at the 60th harmonic of the repetition rate of the Ti:Sapphire oscillators. Their respective time delay is scanned across 12.5 ns requiring a scan time of 10 ms, supporting a time delay resolution of up to 15.6 fs. ASOPS-THz-TDS enables high-resolution spectroscopy that is impossible for a THz-TDS system employing a mechanical delay stage. We measure a timing jitter of 1.36 fs for the system using an air-gap etalon and an optical cross-correlator. We report a Root-Mean-Square deviation of 20.7 MHz and a mean deviation of 14.4 MHz for water absorption lines from 0.5 to 2.7. High-resolution ASOPS-THz-TDS enables high resolution spectroscopy of both gas-phase and condensed-phase samples across a decade of THz bandwidth.

  17. Novel frequency domain techniques and advances in Finite Difference Time domain (FDTD) method for efficient solution of multiscale electromagnetic problems

    Science.gov (United States)

    Panayappan, Kadappan

    With the advent of sub-micron technologies and increasing awareness of Electromagnetic Interference and Compatibility (EMI/EMC) issues, designers are often interested in full- wave solutions of complete systems, taking to account a variety of environments in which the system operates. However, attempts to do this substantially increase the complexities involved in computing full-wave solutions, especially when the problems involve multi- scale geometries with very fine features. For such problems, even the well-established numerical methods, such as the time domain technique FDTD and the frequency domain methods FEM and MoM, are often challenged to the limits of their capabilities. In an attempt to address such challenges, three novel techniques have been introduced in this work, namely Dipole Moment (DM) Approach, Recursive Update in Frequency Domain (RUFD) and New Finite Difference Time Domain ( vFDTD). Furthermore, the efficacy of the above techniques has been illustrated, via several examples, and the results obtained by proposed techniques have been compared with other existing numerical methods for the purpose of validation. The DM method is a new physics-based approach for formulating MoM problems, which is based on the use of dipole moments (DMs), as opposed to the conventional Green's functions. The absence of the Green's functions, as well as those of the vector and scalar potentials, helps to eliminate two of the key sources of difficulties in the conventional MoM formulation, namely the singularity and low-frequency problems. Specifically, we show that there are no singularities that we need to be concerned with in the DM formulation; hence, this obviates the need for special techniques for integrating these singularities. Yet another salutary feature of the DM approach is its ability to handle thin and lossy structures, or whether they are metallic, dielectric-type, or even combinations thereof. We have found that the DM formulation can handle these

  18. Absolute distance measurement using frequency-sweeping heterodyne interferometer calibrated by an optical frequency comb.

    Science.gov (United States)

    Wu, Xuejian; Wei, Haoyun; Zhang, Hongyuan; Ren, Libing; Li, Yan; Zhang, Jitao

    2013-04-01

    We present a frequency-sweeping heterodyne interferometer to measure an absolute distance based on a frequency-tunable diode laser calibrated by an optical frequency comb (OFC) and an interferometric phase measurement system. The laser frequency-sweeping process is calibrated by the OFC within a range of 200 GHz and an accuracy of 1.3 kHz, which brings about a precise temporal synthetic wavelength of 1.499 mm. The interferometric phase measurement system consisting of the analog signal processing circuit and the digital phase meter achieves a phase difference resolution better than 0.1 deg. As the laser frequency is sweeping, the absolute distance can be determined by measuring the phase difference variation of the interference signals. In the laboratory condition, our experimental scheme realizes micrometer accuracy over meter distance.

  19. Frequency domain phase noise analysis of dual injection-locked optoelectronic oscillators.

    Science.gov (United States)

    Jahanbakht, Sajad

    2016-10-01

    Dual injection-locked optoelectronic oscillators (DIL-OEOs) have been introduced as a means to achieve very low-noise microwave oscillations while avoiding the large spurious peaks that occur in the phase noise of the conventional single-loop OEOs. In these systems, two OEOs are inter-injection locked to each other. The OEO with the longer optical fiber delay line is called the master OEO, and the other is called the slave OEO. Here, a frequency domain approach for simulating the phase noise spectrum of each of the OEOs in a DIL-OEO system and based on the conversion matrix approach is presented. The validity of the new approach is verified by comparing its results with previously published data in the literature. In the new approach, first, in each of the master or slave OEOs, the power spectral densities (PSDs) of two white and 1/f noise sources are optimized such that the resulting simulated phase noise of any of the master or slave OEOs in the free-running state matches the measured phase noise of that OEO. After that, the proposed approach is able to simulate the phase noise PSD of both OEOs at the injection-locked state. Because of the short run-time requirements, especially compared to previously proposed time domain approaches, the new approach is suitable for optimizing the power injection ratios (PIRs), and potentially other circuit parameters, in order to achieve good performance regarding the phase noise in each of the OEOs. Through various numerical simulations, the optimum PIRs for achieving good phase noise performance are presented and discussed; they are in agreement with the previously published results. This further verifies the applicability of the new approach. Moreover, some other interesting results regarding the spur levels are also presented.

  20. Relativistic Corrections for Time and Frequency Transfer in Optical Fibres

    CERN Document Server

    Geršl, J; Wolf, P

    2016-01-01

    We derive relativistic corrections for one-way and two-way time and frequency transfer over optical fibres neglecting no terms that exceed 1 ps in time and $10^{-18}$ in fractional frequency, and estimate their magnitude in typical fibre links. We also provide estimates of the uncertainties in the evaluation of the relativistic corrections due to imperfect knowledge of parameters like the coordinates of the fibre and stations, Earth rotation, or thermal effects of the fibre index and length. The links between Teddington(UK) and Paris(F) as well as Braunschweig(D) and Paris(F), that are currently under construction, are studied as specific examples.

  1. Probing the disassembly of ultrafast laser heated gold using frequency domain interferometry.

    Science.gov (United States)

    Ao, Tommy; Ping, Yuan; Lee, Edward

    2005-10-01

    Ultrafast laser heating of a solid offers a unique approach to examine the behavior of non-equilibrium high energy density states. Initially, the electrons are optically excited while the ions in the lattice remain cold. This is followed by electron-electron and electron-phonon relaxation. Recently, experiments were performed in which ultrathin freestanding, gold foils were heated by a femtosecond pump laser to a strongly overdriven regime with energy densities reaching 20 MJ/kg. Interestingly, femtosecond laser reflectivity and transmission measurements on the heated sample revealed a quasi-steady-state behavior before the onset of hydrodynamic expansion. This led to the conjecture of the existence of a metastable, disordered state prior to the disassembly of the solid. To further examine the dynamics of ultrafast laser heated solids, frequency domain interferometry (FDI) was used to provide an independent observation. The highly sensitive change in the phase shift of the FDI probe clearly showed evidence of the quasi-steady-state behavior. The new experiment also yielded a detailed measurement of the time scale of such a quasi-steady-state phase that may help elucidate the process of electron-phonon coupling and disassembly in a strongly overdriven regime.

  2. Spatial mapping of drug delivery to brain tissue using hyperspectral spatial frequency-domain imaging

    Science.gov (United States)

    Singh-Moon, Rajinder P.; Roblyer, Darren M.; Bigio, Irving J.; Joshi, Shailendra

    2014-09-01

    We present an application of spatial frequency-domain imaging (SFDI) to the wide-field imaging of drug delivery to brain tissue. Measurements were compared with values obtained by a previously validated variation of diffuse reflectance spectroscopy, the method of optical pharmacokinetics (OP). We demonstrate a cross-correlation between the two methods for absorption extraction and drug concentration determination in both experimental tissue phantoms and freshly extracted rodent brain tissue. These methods were first used to assess intra-arterial (IA) delivery of cationic liposomes to brain tissue in Sprague Dawley rats under transient cerebral hypoperfusion. Results were found to be in agreement with previously published experimental data and pharmacokinetic models of IA drug delivery. We then applied the same scheme to evaluate IA mitoxantrone delivery to glioma-bearing rats. Good correlation was seen between OP and SFDI determined concentrations taken from normal and tumor averaged sites. This study shows the feasibility of mapping drug/tracer distributions and encourages the use of SFDI for spatial imaging of tissues for drug/tracer-tagged carrier deposition and pharmacokinetic studies.

  3. Integral ceramic superstructure evaluation using time domain optical coherence tomography

    Science.gov (United States)

    Sinescu, Cosmin; Bradu, Adrian; Topala, Florin I.; Negrutiu, Meda Lavinia; Duma, Virgil-Florin; Podoleanu, Adrian G.

    2014-02-01

    Optical Coherence Tomography (OCT) is a non-invasive low coherence interferometry technique that includes several technologies (and the corresponding devices and components), such as illumination and detection, interferometry, scanning, adaptive optics, microscopy and endoscopy. From its large area of applications, we consider in this paper a critical aspect in dentistry - to be investigated with a Time Domain (TD) OCT system. The clinical situation of an edentulous mandible is considered; it can be solved by inserting 2 to 6 implants. On these implants a mesostructure will be manufactured and on it a superstructure is needed. This superstructure can be integral ceramic; in this case materials defects could be trapped inside the ceramic layers and those defects could lead to fractures of the entire superstructure. In this paper we demonstrate that a TD-OCT imaging system has the potential to properly evaluate the presence of the defects inside the ceramic layers and those defects can be fixed before inserting the prosthesis inside the oral cavity. Three integral ceramic superstructures were developed by using a CAD/CAM technology. After the milling, the ceramic layers were applied on the core. All the three samples were evaluated by a TD-OCT system working at 1300 nm. For two of the superstructures evaluated, no defects were found in the most stressed areas. The third superstructure presented four ceramic defects in the mentioned areas. Because of those defects the superstructure may fracture. The integral ceramic prosthesis was send back to the dental laboratory to fix the problems related to the material defects found. Thus, TD-OCT proved to be a valuable method for diagnosing the ceramic defects inside the integral ceramic superstructures in order to prevent fractures at this level.

  4. Acoustic Imaging Frequency Dynamics of Ferroelectric Domains by Atomic Force Microscopy

    Institute of Scientific and Technical Information of China (English)

    ZHAO Kun-Yu; Shunji Takekawa; Kenji Kitamura; ZENG Hua-Rong; SONG Hong-Zhang; HUI Sen-Xing; LI Guo-Rong; YIN Qing-Rui; Kiyoshi Shimamura; Chinna Venkadasamy Kannan; Encarnacion Antonia Garcia Villora

    2008-01-01

    We report the acoustic imaging frequency dynamics of ferroelectric domains by low-frequency acoustic probe microscopy based on the commercial atomic force microscopy. It is found that ferroelectric domain could be firstly visualized at lower frequency down to 0.h kHz by AFM-based acoustic microscopy. The frequency-dependent acoustic signal revealed a strong acoustic response in the frequency range from 7 kHz to lO kHz, and reached maximum at 8.1 kHz. The acoustic contrast mechanism can be ascribed to the different elastic response of ferroelectric microstructures to local elastic stress fields, which is induced by the acoustic wave transmitting in the sample when the piezoelectric transducer is vibrating and exciting acoustic wave under ac electric fields due to normal piezoelectric effects.

  5. Simultaneous transfer of optical frequency and time over 306 km long-haul optical fibre link

    Science.gov (United States)

    Hucl, Vaclav; Cizek, Martin; Pravdova, Lenka; Rerucha, Simon; Hrabina, Jan; Mikel, Bretislav; Smotlacha, Vladimir; Vojtech, Josef; Lazar, Josef; Cip, Ondrej

    2016-12-01

    Optical fibre links for distributing optical frequencies and time stamps were researched and experimentally tested in the past fifteen years. They have been used mainly for stability comparison of experimental optical clocks. But recent development puts demands on a technology transfer from laboratory experiments to the real industry. The remote calibration of interrogators of Fibre Bragg Grating strain sensory networks is one of important examples. The first step of the adoption the time and frequency broadcasting should be the drop-out free long-term operation of this technology between research laboratories connected via long-haul fibre links. We present a 306 km long-haul optical fibre link between the cities of Prague and Brno in the Czech Republic where a coherent transfer of stable optical frequency and a stable time signal has been firstly demonstrated. The link between ISI CAS Brno and CESNET Prague uses an internet communication fibre where a window of 1540-1546 nm is dedicated for the coherent transfer and 1PPS signal. The link is equipped with 6 bidirectional EDFA amplifiers. The optical frequency standard based on the highly-coherent laser Koheras Adjustik working at 1540.5 nm and stabilized with a saturation absorption spectroscopy technique was used for the coherent wave transfer. The suppression of the Doppler shift induced by the optical fibre was based on an accoustooptical modulator with a servo-loop including a fast PID controller processing the beat-note frequency given by mixing of the Adjustik laser (Brno) and the reflected frequency of this laser from the far end of 306 km long-haul fibre link (Prague). We verified the Doppler shift suppression for the coherent wave with a measuring method analysing the transport delay of the 1PPS signal.

  6. Strong optical feedback in birefringent dual frequency laser

    Institute of Scientific and Technical Information of China (English)

    Mao Wei; Zhang Shu-Lian

    2006-01-01

    Strong optical feedback in a birefringent dual frequency He-Ne laser with a high reflectivity feedback mirror has been investigated for the first time. The output characteristics of two orthogonally polarized modes are demonstrated in two different optical feedback cases: one is for both modes being fed back and the other is for only one of the modes being fed back. Strong mode competition can be observed between the two modes with strong optical feedback. And when one mode's intensity is near its maximum, the other mode is nearly extinguished. When both modes are fed back into the laser cavity, the mode competition is stronger than when only one mode is fed back. The difference in initial intensity between the two orthogonally polarized modes plays an important role in the mode competition, which has been experimentally and theoretically demonstrated.

  7. Spectral domain optical coherence tomography with dual-balanced detection

    Science.gov (United States)

    Bo, En; Liu, Xinyu; Chen, Si; Luo, Yuemei; Wang, Nanshuo; Wang, Xianghong; Liu, Linbo

    2016-03-01

    We developed a spectral domain optical coherence tomography (SD-OCT) system employing dual-balanced detection (DBD) for direct current term suppression and SNR enhancement, especially for auto-autocorrelation artifacts reduction. The DBD was achieved by using a beam splitter to building a free-space Michelson interferometer, which generated two interferometric spectra with a phase difference of π. These two phase-opposed spectra were guided to the spectrometer through two single mode fibers of the 8 fiber v-groove array and acquired by ultizing the upper two lines of a three-line CCD camera. We rotated this fiber v-groove array by 1.35 degrees to focus two spectra onto the first and second line of the CCD camera. Two spectra were aligned by optimum spectrum matching algorithm. By subtracting one spectrum from the other, this dual-balanced detection system achieved a direct current term suppression of ~30 dB, SNR enhancement of ~3 dB, and auto-autocorrelation artifacts reduction of ~10 dB experimentally. Finally we respectively validated the feasibility and performance of dual-balanced detection by imaging a glass plate and swine corneal tissue ex vivo. The quality of images obtained using dual-balanced detection was significantly improved with regard to the conventional single-detection (SD) images.

  8. Retinal Imaging of Infants on Spectral Domain Optical Coherence Tomography

    Directory of Open Access Journals (Sweden)

    Anand Vinekar

    2015-01-01

    Full Text Available Spectral domain coherence tomography (SD OCT has become an important tool in the management of pediatric retinal diseases. It is a noncontact imaging device that provides detailed assessment of the microanatomy and pathology of the infant retina with a short acquisition time allowing office examination without the requirement of anesthesia. Our understanding of the development and maturation of the infant fovea has been enhanced by SD OCT allowing an in vivo assessment that correlates with histopathology. This has helped us understand the critical correlation of foveal development with visual potential in the first year of life and beyond. In this review, we summarize the recent literature on the clinical applications of SD OCT in studying the pathoanatomy of the infant macula, its ability to detect subclinical features, and its correlation with disease and vision. Retinopathy of prematurity and macular edema have been discussed in detail. The review also summarizes the current status of SD OCT in other infant retinal conditions, imaging the optic nerve, the choroid, and the retinal nerve fibre in infants and children, and suggests future areas of research.

  9. Characterization of PET preforms using spectral domain optical coherence tomography

    Science.gov (United States)

    Hosseiny, Hamid; Ferreira, Manuel João.; Martins, Teresa; Carmelo Rosa, Carla

    2013-11-01

    Polyethylene terephthalate (PET) preforms are massively produced nowadays with the purpose of producing food and beverages packaging and liquid containers. Some varieties of these preforms are produced as multilayer structures, where very thin inner film(s) act as a barrier for nutrients leakage. The knowledge of the thickness of this thin inner layer is important in the production line. The quality control of preforms production requires a fast approach and normally the thickness control is performed by destructive means out of the production line. A spectral domain optical coherence tomography (SD-OCT) method was proposed to examine the thin layers in real time. This paper describes a nondestructive approach and all required signal processing steps to characterize the thin inner layers and also to improve the imaging speed and the signal to noise ratio. The algorithm was developed by using graphics processing unit (GPU) with computer unified device architecture (CUDA). This GPU-accelerated white light interferometry technique nondestructively assesses the samples and has high imaging speed advantage, overcoming the bottlenecks in PET performs quality control.

  10. Spectral Domain Optical Coherence Tomography Findings in Posterior Microphthalmia

    Directory of Open Access Journals (Sweden)

    Emine Tınkır Kayıtmazbatır

    2014-05-01

    Full Text Available The retinal spectral domain optical coherence tomography (SD-OCT findings of two posterior microphthalmia cases are presented in this case report. For this purpose, the findings of two siblings aged five and seven years who presented to our clinic with the complain of far-sightedness and high hypermetropia were evaluated. Both cases diagnosed to have posterior microphthalmia demonstrated normal biomicroscopic anterior segment examination and gonioscopy findings and the axial lengths were measured to be shorter than 17mm. The SD-OCT analysis of papillomacular folds detected in fundus examination revealed contribution of only neurosensorial retina. Beneath the retinal fold, we observed bilateral cysts in the intraretinal area in one of the cases and a triangle-shaped hyporeflective space with an apex corresponding to that of the retinal fold in the subretinal area in both cases. SD-OCT is an adjunctive imaging tool for diagnosis and follow-up of degenerative changes in posterior microphthalmia. These changes may be also important for visual prognosis. (Turk J Ophthalmol 2014; 44: 240-2

  11. Frequency-time coherence for all-optical sampling without optical pulse source

    Science.gov (United States)

    Preußler, Stefan; Raoof Mehrpoor, Gilda; Schneider, Thomas

    2016-09-01

    Sampling is the first step to convert an analogue optical signal into a digital electrical signal. The latter can be further processed and analysed by well-known electrical signal processing methods. Optical pulse sources like mode-locked lasers are commonly incorporated for all-optical sampling, but have several drawbacks. A novel approach for a simple all-optical sampling is to utilise the frequency-time coherence of each signal. The method is based on only using two coupled modulators driven with an electrical sine wave. Since no optical source is required, a simple integration in appropriate platforms, such as Silicon Photonics might be possible. The presented method grants all-optical sampling with electrically tunable bandwidth, repetition rate and time shift.

  12. Comparing a mercury optical lattice clock with microwave and optical frequency standards

    Science.gov (United States)

    Tyumenev, R.; Favier, M.; Bilicki, S.; Bookjans, E.; Le Targat, R.; Lodewyck, J.; Nicolodi, D.; Le Coq, Y.; Abgrall, M.; Guéna, J.; De Sarlo, L.; Bize, S.

    2016-11-01

    In this paper we report the evaluation of an optical lattice clock based on neutral mercury with a relative uncertainty of 1.7× {10}-16. Comparing this characterized frequency standard to a 133Cs atomic fountain we determine the absolute frequency of the {}1{{{S}}}0\\to {}3{{{P}}}0 transition of 199Hg as {ν }{Hg}=1128 575 290 808 154.62 {Hz}+/- 0.19 {Hz}({statistical})+/- 0.38 {Hz} (systematic), limited solely by the realization of the SI second. Furthermore, by comparing the mercury optical lattice clock to a 87Rb atomic fountain, we determine for the first time to our knowledge the ratio between the 199Hg clock transition and the 87Rb ground state hyperfine transition. Finally we present a direct optical to optical measurement of the 199Hg/87Sr frequency ratio. The obtained value of {ν }{Hg}/{ν }{Sr} = 2.629 314 209 898 909 15 with a fractional uncertainty of 1.8× {10}-16 is in excellent agreement with a similar measurement obtained by Yamanaka et al (2015 Phys. Rev. Lett. 114 230801). This makes this frequency ratio one of the few physical quantities agreed upon by different laboratories to this level of uncertainty. Frequency ratio measurements of the kind reported in this paper have a strong impact for frequency metrology and fundamental physics as they can be used to monitor putative variations of fundamental constants.

  13. A hybrid analysis method for linear dynamic soil-structure interaction in time and frequency domain

    Institute of Scientific and Technical Information of China (English)

    丁海平; 廖振鹏

    2001-01-01

    A hybrid analysis method in time and frequency domains for linear soil-structure interaction is presented. First, the time domain solution of the system with Rayleigh damping excited by a short time impulse is obtained by the decoupling numerical simulation technique of near-field wave motion. Then, the corresponding frequency domain solution can be got by Fourier transform. According to the relationship between damping value and dynamic re-sponse of a system, the solution of the system with complex damping can be got by Taylor expansion. The hybrid method makes the best of decoupling and explicit algorithm in time domain, and increases the calculation efficien-cy for linear soil-structure interaction analysis.

  14. High-Performance Optical Frequency References for Space

    Science.gov (United States)

    Schuldt, Thilo; Döringshoff, Klaus; Milke, Alexander; Sanjuan, Josep; Gohlke, Martin; Kovalchuk, Evgeny V.; Gürlebeck, Norman; Peters, Achim; Braxmaier, Claus

    2016-06-01

    A variety of future space missions rely on the availability of high-performance optical clocks with applications in fundamental physics, geoscience, Earth observation and navigation and ranging. Examples are the gravitational wave detector eLISA (evolved Laser Interferometer Space Antenna), the Earth gravity mission NGGM (Next Generation Gravity Mission) and missions, dedicated to tests of Special Relativity, e.g. by performing a Kennedy- Thorndike experiment testing the boost dependence of the speed of light. In this context we developed optical frequency references based on Doppler-free spectroscopy of molecular iodine; compactness and mechanical and thermal stability are main design criteria. With a setup on engineering model (EM) level we demonstrated a frequency stability of about 2·10-14 at an integration time of 1 s and below 6·10-15 at integration times between 100s and 1000s, determined from a beat-note measurement with a cavity stabilized laser where a linear drift was removed from the data. A cavity-based frequency reference with focus on improved long-term frequency stability is currently under development. A specific sixfold thermal shield design based on analytical methods and numerical calculations is presented.

  15. Practical iterative learning control with frequency domain design and sampled data implementation

    CERN Document Server

    Wang, Danwei; Zhang, Bin

    2014-01-01

    This book is on the iterative learning control (ILC) with focus on the design and implementation. We approach the ILC design based on the frequency domain analysis and address the ILC implementation based on the sampled data methods. This is the first book of ILC from frequency domain and sampled data methodologies. The frequency domain design methods offer ILC users insights to the convergence performance which is of practical benefits. This book presents a comprehensive framework with various methodologies to ensure the learnable bandwidth in the ILC system to be set with a balance between learning performance and learning stability. The sampled data implementation ensures effective execution of ILC in practical dynamic systems. The presented sampled data ILC methods also ensure the balance of performance and stability of learning process. Furthermore, the presented theories and methodologies are tested with an ILC controlled robotic system. The experimental results show that the machines can work in much h...

  16. USING CROSS-CORRELATION THEORY TO EXTRACT MODAL PARAMETERS IN FREQUENCY-DOMAIN

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Conventional modal parameter identifications are usually based on frequency response functions, which require measurements of both the input force and the resulting response. However, in many cases, only response data are available while the actual excitations (such as wind/wave load) are not measurable. Modal parameters estimation must base itself on response-only data. Over the past years, many time-domain modal parameter identification techniques from output-only are proposed. A poly-reference frequency-domain modal identification scheme on response-only is presented. It is based on coupling the cross-correlation theory with conventional frequency-domain modal parameter extraction. An experiment using an airplane model is performed to verify the proposed method.

  17. Frequency-Domain Adaptive Algorithm for Network Echo Cancellation in VoIP

    Directory of Open Access Journals (Sweden)

    Patrick A. Naylor

    2008-05-01

    Full Text Available We propose a new low complexity, low delay, and fast converging frequency-domain adaptive algorithm for network echo cancellation in VoIP exploiting MMax and sparse partial (SP tap-selection criteria in the frequency domain. We incorporate these tap-selection techniques into the multidelay filtering (MDF algorithm in order to mitigate the delay inherent in frequency-domain algorithms. We illustrate two such approaches and discuss their tradeoff between convergence performance and computational complexity. Simulation results show an improvement in convergence rate for the proposed algorithm over MDF and significantly reduced complexity. The proposed algorithm achieves a convergence performance close to that of the recently proposed, but substantially more complex improved proportionate MDF (IPMDF algorithm.

  18. A frequency domain design of PID controller for an AVR system

    Institute of Scientific and Technical Information of China (English)

    Md Nishat ANWAR; Somnath PAN

    2014-01-01

    We propose a new proportional-integral-derivative (PID) controller design method for an automatic voltage regula-tion (AVR) system based on approximate model matching in the frequency domain. The parameters of the PID controller are obtained by approximate frequency response matching between the closed-loop control system and a reference model with the desired specifications. Two low frequency points are required for matching the frequency response, and the design method yields linear algebraic equations, solution of which gives the controller parameters. The effectiveness of the proposed method is demonstrated through examples taken from the literature and comparison with some popular methods.

  19. Optical Frequency Comb Spectroscopy of Rare Earth Atoms

    Science.gov (United States)

    Swiatlowski, Jerlyn; Palm, Christopher; Joshi, Trinity; Montcrieffe, Caitlin; Jackson Kimball, Derek

    2013-05-01

    We discuss progress in our experimental program to employ optical-frequency-comb-based spectroscopy to understand the complex spectra of rare-earth atoms. We plan to carry out systematic measurements of atomic transitions in rare-earth atoms to elucidate the energy level structure and term assignment and determine presently unknown atomic state parameters. This spectroscopic information is important in view of the increasing interest in rare-earth atoms for atomic frequency standards, in astrophysical investigations of chemically peculiar stars, and in tests of fundamental physics (tests of parity and time-reversal invariance, searches for time variation of fundamental constants, etc.). We are presently studying the use of hollow cathode lamps as atomic sources for two-photon frequency comb spectroscopy. Supported by the National Science Foundation under grant PHY-0958749.

  20. Optically transparent frequency selective surfaces on flexible thin plastic substrates

    Directory of Open Access Journals (Sweden)

    Aliya A. Dewani

    2015-02-01

    Full Text Available A novel 2D simple low cost frequency selective surface was screen printed on thin (0.21 mm, flexible transparent plastic substrate (relative permittivity 3.2. It was designed, fabricated and tested in the frequency range 10-20 GHz. The plane wave transmission and reflection coefficients agreed with numerical modelling. The effective permittivity and thickness of the backing sheet has a significant effect on the frequency characteristics. The stop band frequency reduced from 15GHz (no backing to 12.5GHz with polycarbonate. The plastic substrate thickness beyond 1.8mm has minimal effect on the resonant frequency. While the inner element spacing controls the stop-band frequency, the substrate thickness controls the bandwidth. The screen printing technique provided a simple, low cost FSS fabrication method to produce flexible, conformal, optically transparent and bio-degradable FSS structures which can find their use in electromagnetic shielding and filtering applications in radomes, reflector antennas, beam splitters and polarizers.

  1. A Cs-Based Optical Frequency Measurement Using Cross-Linked Optical and Microwave Oscillators

    CERN Document Server

    Tamm, Chr; Lipphardt, B; Gerginov, V; Nemitz, N; Kazda, M; Weyers, S; Peik, E

    2013-01-01

    We describe a measurement of the frequency of the 2S1/2(F = 0) - 2D3/2(F' = 2) transition of 171Yb+ at the wavelength 436 nm (frequency 688 THz), using a single Yb+ ion confined in a Paul trap and two caesium fountains as references. In one of the fountains, the frequency of the microwave oscillator that interrogates the caesium atoms is stabilized by the laser that excites the Yb+ reference transition with a linewidth in the hertz range. The stability is transferred to the microwave oscillator with the use of a fiber laser based optical frequency comb generator that also provides the frequency conversion for the absolute frequency measurement. The frequency comb generator is configured as a transfer oscillator so that fluctuations of the pulse repetition rate and of the carrier offset frequency do not degrade the stability of the frequency conversion. The phase noise level of the generated ultrastable microwave signal is comparable to that of a cryogenic sapphire oscillator. For fountain operation with optic...

  2. Imaging patients with glaucoma using spectral-domain optical coherence tomography and optical microangiography

    Science.gov (United States)

    Auyeung, Kris; Auyeung, Kelsey; Kono, Rei; Chen, Chieh-Li; Zhang, Qinqin; Wang, Ruikang K.

    2015-03-01

    In ophthalmology, a reliable means of diagnosing glaucoma in its early stages is still an open issue. Past efforts, including forays into fluorescent angiography (FA) and early optical coherence tomography (OCT) systems, to develop a potential biomarker for the disease have been explored. However, this development has been hindered by the inability of the current techniques to provide useful depth and microvasculature information of the optic nerve head (ONH), which have been debated as possible hallmarks of glaucoma progression. We reasoned that a system incorporating a spectral-domain OCT (SD-OCT) based Optical Microangiography (OMAG) system, could allow an effective, non-invasive methodology to evaluate effects on microvasculature by glaucoma. SD-OCT follows the principle of light reflection and interference to produce detailed cross-sectional and 3D images of the eye. OMAG produces imaging contrasts via endogenous light scattering from moving particles, allowing for 3D image productions of dynamic blood perfusion at capillary-level resolution. The purpose of this study was to investigate the optic cup perfusion (flow) differences in glaucomatous and normal eyes. Images from three normal and five glaucomatous subjects were analyzed our OCT based OMAG system for blood perfusion and structural images, allowing for comparisons. Preliminary results from blood flow analysis revealed reduced blood perfusion within the whole-depth region encompassing the Lamina Cribrosa in glaucomatous cases as compared to normal ones. We conclude that our OCT-OMAG system may provide promise and viability for glaucoma screening.

  3. Performance of Downlink Frequency Domain Packet Scheduling for the UTRAN Long Term Evolution

    DEFF Research Database (Denmark)

    Pokhariyal, Akhilesh; Kolding, Troels E.; Mogensen, Preben

    2006-01-01

     In this paper we investigate the potential of downlink frequency-domain packet scheduling (FDPS) for the 3GPP UTRAN long term evolution. Utilizing frequency-domain channel quality reports, the scheduler flexibly multiplexes users on different portions of the system bandwidth. Compared to frequen...... Urban channel profile, studies show that the scheduling resolution should preferably be as low as 375 kHz to yield significant FDPS gain and the std. of the error of radio state reports need to be kept within 1.5-2 dB....

  4. Nonlinear system identification NARMAX methods in the time, frequency, and spatio-temporal domains

    CERN Document Server

    Billings, Stephen A

    2013-01-01

    Nonlinear System Identification: NARMAX Methods in the Time, Frequency, and Spatio-Temporal Domains describes a comprehensive framework for the identification and analysis of nonlinear dynamic systems in the time, frequency, and spatio-temporal domains. This book is written with an emphasis on making the algorithms accessible so that they can be applied and used in practice. Includes coverage of: The NARMAX (nonlinear autoregressive moving average with exogenous inputs) modelThe orthogonal least squares algorithm that allows models to be built term by

  5. The capability of time- and frequency-domain algorithms for bistatic SAR processing

    Science.gov (United States)

    Vu, Viet T.; Sjögren, Thomas K.; Pettersson, Mats I.

    2013-05-01

    The paper presents a study of the capability of time- and frequency-domain algorithms for bistatic SAR processing. Two typical algorithms, Bistatic Fast Backprojection (BiFBP) and Bistatic Range Doppler (BiRDA), which are both available for general bistatic geometry, are selected as the examples of time- and frequency-domain algorithms in this study. Their capability is evaluated based on some criteria such as processing time required by the algorithms to reconstruct SAR images from bistatic SAR data and the quality assessments of those SAR images.

  6. Consensus for Linear Multiagent Systems With Time-Varying Delays: A Frequency Domain Perspective.

    Science.gov (United States)

    Chen, Yuanye; Shi, Yang

    2016-07-27

    This paper investigates the consensus problem for multiagent systems with time-varying delays. The bounded delays can be arbitrarily fast time-varying. The communication topology is assumed to be undirected and fixed. With general linear dynamics under average state feedback protocols, the consensus problem is then transformed into the robust control problem. Further, sufficient frequency domain criteria are established in terms of small gain theorem by analyzing the delay dependent gains for both continuous-time and discrete-time systems. The controller synthesis problems can be solved by applying the frequency domain design methods. Numerical examples are demonstrated to verify the effectiveness of the proposed approaches.

  7. Measurement of the optical properties of skin using terahertz time-domain spectroscopic techniques

    Science.gov (United States)

    Wilmink, Gerald J.; Ibey, Bennett L.; Tongue, Thomas; Schulkin, Brian; Peralta, Xomalin; Rivest, Benjamin D.; Haywood, Eric C.; Roach, William P.

    2010-02-01

    Terahertz (THz) radiation is increasingly being used in biomedical imaging and spectroscopy applications. These techniques show tremendous promise to provide new sophisticated tools for the improved detection of skin cancer. However, despite recent efforts to develop these applications, few studies have been conducted to characterize the optical properties of skin at THz frequencies. Such information is required to better understand THz-tissue interactions, and is critical for determining the feasibility of proposed applications. In this study, we have developed and tested a THz time-domain spectroscopy system. We used this system to acquire the optical properties for fresh and frozen/thawed excised porcine skin from 0.1 to 2.0 THz. Results show that the index of refraction (n) for both frozen and fresh skin decreases with frequency. For frozen skin, n equals 2.5 at 0.1 THz and 2.0 at 2.0 THz, and for fresh skin equals 2.0 at 0.1 THz and 1.7 at 2.0 THz. Values for the absorption coefficient (μa) increase with frequency for both frozen and fresh skin. Frozen skin exhibits μa values equal to 56 cm-1 at 0.1 THz and 550 cm-1 at 2.0 THz, whereas fresh skin exhibits values of 56 cm-1 at 0.1 THz and 300 cm-1 at 2.0 THz. Assuming the optical penetration depth (δ) is inversely proportional to μa (absorption-dominated interactions), THz radiation has limited δ in skin (200 μm at 0.1 THz to 40 μm at 2.0 THz). These results suggest that applications exploiting THz radiation show the most promise for investigating superficial tissues.

  8. Mid-Infrared Optical Frequency Combs based on Difference Frequency Generation for Molecular Spectroscopy

    CERN Document Server

    Cruz, Flavio C; Johnson, Todd; Ycas, Gabriel; Klose, Andrew; Giorgetta, Fabrizio R; Coddington, Ian; Diddams, Scott A

    2015-01-01

    Mid-infrared femtosecond optical frequency combs were produced by difference frequency generation of the spectral components of a near-infrared comb in a 3-mm-long MgO:PPLN crystal. We observe strong pump depletion and 9.3 dB parametric gain in the 1.5 \\mu m signal, which yields powers above 500 mW (3 \\mu W/mode) in the idler with spectra covering 2.8 \\mu m to 3.5 \\mu m. Potential for broadband, high-resolution molecular spectroscopy is demonstrated by absorption spectra and interferograms obtained by heterodyning two combs.

  9. A diode laser spectrometer at 634 nm and absolute frequency measurements using optical frequency comb

    Institute of Scientific and Technical Information of China (English)

    Yi Lin; Yuan Jie; Qi Xiang-Hui; Chen Wen-Lan; Zhou Da-Wei; Zhou Tong; Zhou Xiao-Ji; Chen Xu-Zong

    2009-01-01

    This paper reports that two identical external-cavity-diode-laser(ECDL)based spectrometers are constructed at 634 nm referencing on the hyperfine B-X transition a(80)8-4 of 127I2.The lasers are stabilized on the Doppler-free absorption signals using the third-harmonic detection technique.The instability of the stabilized laser is measured to be 2.8×10-12(after 1000 s)by counting the beat note between the two lasers.The absolute optical frequency of the transition is,for the first time,determined to be 472851936189.5 kHz by using an optical frequency comb referenced on the microwave caesium atomic clock.The uncertainty of the measurement is less than 4.9 kHz.

  10. A frequency domain radar interferometric imaging (FII) technique based on high-resolution methods

    Science.gov (United States)

    Luce, H.; Yamamoto, M.; Fukao, S.; Helal, D.; Crochet, M.

    2001-01-01

    In the present work, we propose a frequency-domain interferometric imaging (FII) technique for a better knowledge of the vertical distribution of the atmospheric scatterers detected by MST radars. This is an extension of the dual frequency-domain interferometry (FDI) technique to multiple frequencies. Its objective is to reduce the ambiguity (resulting from the use of only two adjacent frequencies), inherent with the FDI technique. Different methods, commonly used in antenna array processing, are first described within the context of application to the FII technique. These methods are the Fourier-based imaging, the Capon's and the singular value decomposition method used with the MUSIC algorithm. Some preliminary simulations and tests performed on data collected with the middle and upper atmosphere (MU) radar (Shigaraki, Japan) are also presented. This work is a first step in the developments of the FII technique which seems to be very promising.

  11. Frequency Domain Modeling and Simulation of DC Power Electronic Systems Using Harmonic State Space Method

    DEFF Research Database (Denmark)

    Kwon, Jun Bum; Wang, Xiongfei; Blaabjerg, Frede

    2016-01-01

    For the efficiency and simplicity of electric systems, the dc power electronic systems are widely used in a variety of applications such as electric vehicles, ships, aircraft and also in homes. In these systems, there could be a number of dynamic interactions and frequency coupling between network...... with different switching frequency or harmonics from ac-dc converters makes that harmonics and frequency coupling are both problems of ac system and challenges of dc system. This paper presents a modeling and simulation method for a large dc power electronic system by using Harmonic State Space (HSS) modeling...... and loads and other converters. Hence, time-domain simulations are usually required to consider such a complex system behavior. However, simulations in the time-domain may increase the calculation time and the utilization of computer memory. Furthermore, frequency coupling driven by multiple converters...

  12. Macular thickness measurements using Copernicus Spectral Domain Optical Coherence Tomography.

    Science.gov (United States)

    Gella, Laxmi; Raman, Rajiv; Sharma, Tarun

    2015-01-01

    To provide normal macular thickness measurements using Spectral Domain Optical Coherence Tomography (SDOCT, Copernicus, Optopol Technologies, Zawierci, Poland). Fifty-eight eyes of 58 healthy subjects were included in this prospective study. All subjects had comprehensive ophthalmic examination including best-corrected visual acuity (BCVA). All the subjects underwent Copernicus SDOCT. Central foveal thickness (CFT) and photoreceptor layer (PRL) thickness were measured and expressed as mean and standard deviation. Mean retinal thickness for each of the 9 regions defined in the Early Treatment Diabetic Retinopathy Study was reported. The data were compared with published literature in Indians using Stratus and Spectralis OCTs to assess variation in instrument measurements. The mean CFT in the study sample was 173.8 ± 18.16 microns (131-215 microns) and the mean PRL thickness was 65.48 ± 4.23 microns (56-74 microns). No significant difference (p = 0.148) was found between CFT measured automated (179.28 ± 22 microns) and manually (173.83 ± 18.1 microns). CFT was significantly lower in women (167.62 ± 16.36 microns) compared to men (180.03 ± 18 microns) (p = 0.008). Mean retinal thickness reported in this study was significantly different from published literature using Stratus OCT and Spectralis OCT. We report the normal mean retinal thickness in central 1 mm area to be between 138 and 242 microns in Indian population using Copernicus SDOCT. We suggest that different OCT instruments cannot be used interchangeably for the measurement of macular thickness as they vary in segmentation algorithms.

  13. Frequency comparison of optical lattice clocks beyond the Dick limit

    Science.gov (United States)

    Takamoto, Masao; Takano, Tetsushi; Katori, Hidetoshi

    2011-05-01

    The supreme accuracy of atomic clocks relies on the universality of atomic transition frequencies. The stability of a clock, meanwhile, measures how quickly the clock's statistical uncertainties are reduced. The ultimate measure of stability is provided by the quantum projection noise, which improves as 1/√N by measuring N uncorrelated atoms. Quantum projection noise limited stabilities have been demonstrated in caesium clocks and in single-ion optical clocks, where the quantum noise overwhelms the Dick effect attributed to local oscillator noise. Here, we demonstrate a synchronous frequency comparison of two optical lattice clocks using 87Sr and 88Sr atoms, respectively, for which the Allan standard deviation reached 1 × 10-17 in an averaging time of 1,600 s by cancelling out the Dick effect to approach the quantum projection noise limit. The scheme demonstrates the advantage of using a large number (N ~ 1,000) of atoms in optical clocks and paves the way to investigating the inherent uncertainties of clocks and relativistic geodesy on a timescale of tens of minutes.

  14. Frequency-time coherence for all-optical sampling without optical pulse source

    CERN Document Server

    Preussler, Stefan; Schneider, Thomas

    2016-01-01

    Sampling is the first step to convert an analogue optical signal into a digital electrical signal. The latter can be further processed and analysed by well-known electrical signal processing methods. Optical pulse sources like mode-locked lasers are commonly incorporated for all-optical sampling, but have several drawbacks. A novel approach for a simple all-optical sampling is to utilise the frequency-time coherence of each signal. The method is based on only using two coupled modulators driven with an electrical sine wave, allowing simple integration in appropriate platforms, such as Silicon Photonics. The presented method grants all-optical sampling with electrically tunable bandwidth, repetition rate and time shift.

  15. Nonlinear optics at low powers: new mechanism of on-chip optical frequency comb generation

    CERN Document Server

    Rogov, Andrei

    2016-01-01

    Nonlinear optical effects provide a natural way of light manipulation and interaction, and form the foundation of applied photonics -- from high-speed signal processing and telecommunication, to ultra-high bandwidth interconnects and information processing. However, relatively weak nonlinear response at optical frequencies calls for operation at high optical powers, or boosting efficiency of nonlinear parametric processes by enhancing local field intensity with high quality-factor resonators near cavity resonance, resulting in reduced operational bandwidth and increased loss due to multi-photon absorption. Here, we present an alternative to this conventional approach, with strong nonlinear optical effects at substantially lower local intensities, based on period-doubling bifurcations near nonlinear cavity anti-resonance, and apply it to low-power optical comb generation in a silicon chip.

  16. Fast simulation approaches for power fluctuation model of wind farm based on frequency domain

    DEFF Research Database (Denmark)

    Lin, Jin; Gao, Wen-zhong; Sun, Yuan-zhang

    2012-01-01

    This paper discusses one model developed by Riso, DTU, which is capable of simulating the power fluctuation of large wind farms in frequency domain. In the original design, the “frequency-time” transformations are time-consuming and might limit the computation speed for a wind farm of large size....... is more than 300 times if all these approaches are adopted, in any low, medium and high wind speed test scenarios....

  17. Frequency-domain equalization for OFDMA-based multiuser MIMO systems with improper modulation schemes

    Directory of Open Access Journals (Sweden)

    Wu Yi

    2011-01-01

    Full Text Available Abstract In this paper, we propose a novel transceiver structure for orthogonal frequency division multiple access-based uplink multiuser multiple-input multiple-output systems. The numerical results show that the proposed frequency-domain equalization schemes significantly outperform conventional linear minimum mean square error-based equalizers in terms of bit error rate performance with moderate increase in computational complexity.

  18. Association between Frequency Domain Heart Rate Variability and Unplanned Readmission to Hospital in Geriatric Patients

    Directory of Open Access Journals (Sweden)

    Fu Chin-Hua

    2011-02-01

    Full Text Available Abstract Background An accurate prediction of unplanned readmission (UR after discharge from hospital can facilitate physician's decision making processes for providing better quality of care in geriatric patients. The objective of this study was to explore the association of cardiac autonomic functions as measured by frequency domain heart rate variability (HRV and 14-day UR in geriatric patients. Methods Patients admitted to the geriatric ward of a regional hospital in Chiayi county in Taiwan were followed prospectively from July 2006 to June 2007. Those with invasive tubes and those who were heavy smokers, heavy alcohol drinkers, on medications that might influence HRV, or previously admitted to the hospital within 30 days were excluded. Cardiac autonomic functions were evaluated by frequency domain indices of HRV. Multiple logistic regression was used to assess the association between UR and HRV indices adjusted for age and length of hospitalization. Results A total of 78 patients met the inclusion criteria and 15 of them were readmitted within 14 days after discharge. The risk of UR was significantly higher in patients with lower levels of total power (OR = 1.39; 95% CI = 1.04-2.00, low frequency power (LF (OR = 1.22; 95% CI = 1.03-1.49, high frequency power (HF (OR = 1.27; 95% CI = 1.02-1.64, and lower ratios of low frequency power to high frequency power (LF/HF ratio (OR = 1.96; 95% CI = 1.07-3.84. Conclusion This is the first study to evaluate the association between frequency domain heart rate variability and the risk of UR in geriatric patients. Frequency domain heart rate variability indices measured on admission were significantly associated with increased risk of UR in geriatric patients. Additional studies are required to confirm the value and feasibility of using HRV indices on admission as a non-invasive tool to assist the prediction of UR in geriatric patients.

  19. Effect of soil temperature on optical frequency transfer through unidirectional dense-wavelength-division-multiplexing fiber-optic links.

    Science.gov (United States)

    Pinkert, T J; Böll, O; Willmann, L; Jansen, G S M; Dijck, E A; Groeneveld, B G H M; Smets, R; Bosveld, F C; Ubachs, W; Jungmann, K; Eikema, K S E; Koelemeij, J C J

    2015-02-01

    Results of optical frequency transfer over a carrier-grade dense-wavelength-division-multiplexing (DWDM) optical fiber network are presented. The relation between soil temperature changes on a buried optical fiber and frequency changes of an optical carrier through the fiber is modeled. Soil temperatures, measured at various depths by the Royal Netherlands Meteorology Institute (KNMI) are compared with observed frequency variations through this model. A comparison of a nine-day record of optical frequency measurements through the 2×298  km fiber link with soil temperature data shows qualitative agreement. A soil temperature model is used to predict the link stability over longer periods (days-months-years). We show that optical frequency dissemination is sufficiently stable to distribute and compare, e.g., rubidium frequency standards over standard DWDM optical fiber networks using unidirectional fibers.

  20. Invited Article: A compact optically coherent fiber frequency comb.

    Science.gov (United States)

    Sinclair, L C; Deschênes, J-D; Sonderhouse, L; Swann, W C; Khader, I H; Baumann, E; Newbury, N R; Coddington, I

    2015-08-01

    We describe the design, fabrication, and performance of a self-referenced, optically coherent frequency comb. The system robustness is derived from a combination of an optics package based on polarization-maintaining fiber, saturable absorbers for mode-locking, high signal-to-noise ratio (SNR) detection of the control signals, and digital feedback control for frequency stabilization. The output is phase-coherent over a 1-2 μm octave-spanning spectrum with a pulse repetition rate of ∼200 MHz and a residual pulse-to-pulse timing jitter <3 fs well within the requirements of most frequency-comb applications. Digital control enables phase coherent operation for over 90 h, critical for phase-sensitive applications such as timekeeping. We show that this phase-slip free operation follows the fundamental limit set by the SNR of the control signals. Performance metrics from three nearly identical combs are presented. This laptop-sized comb should enable a wide-range of applications beyond the laboratory.

  1. Dental depth profilometry using simultaneous frequency-domain infrared photothermal radiometry and laser luminescence for the diagnosis of dental caries

    Science.gov (United States)

    Nicolaides, Lena; Garcia, Jose A.; Mandelis, Andreas; Abrams, Stephen H.

    2001-04-01

    Frequency-domain IR photothermal radiometry is introduced as a dynamic dental diagnostic tool and its main features are compared with modulated laser luminescence for quantifying sound and carious enamel or dentin. Dental caries found in the fissures or grooves of teeth is very difficult to diagnose or quantify with the present clinical techniques. Visual examination and dental radiographs do not detect the presence of decay until there has been significant carious destruction of the tooth. A high-spatial-resolution dynamic experimental imaging set-up, which can provide simultaneous measurements of laser-induced frequency-domain IR photothermal radiometric and luminescence signals form defects in teeth, was developed. Following optical absorption of laser photons, the new set-up can monitor simultaneously and independently the non-radiative conversion, and the radiative de-excitation in turbid media such as hard dental tissue. This work is intended to show the complementarity between modulated luminescence and photothermal frequency scans in detecting carious lesions in teeth. A sound extracted molar with a dentin-enamel interface was introduced to examine the depth profilometric abilities of the method. Occlusal surfaces of teeth with potential areas of demineralization or carious destruction in the fissures were examined and compared to the signals produced by the sound enamel establishing the depth profilometric abilities of the method. The significance to clinical dentistry lies in the potential of this technique to detect and monitor early carious lesions in the pits and fissures of teeth.

  2. DWDM Fiber-Wireless Access System with Centralized Optical Frequency Comb-based RF Carrier Generation

    DEFF Research Database (Denmark)

    Pang, Xiaodan; Beltrán, Marta; Sánchez, José;

    2013-01-01

    We propose and experimentally demonstrate an optical wireless DWDM system at 60 GHz with optical incoherent heterodyne up-conversion using an optical frequency comb. Multiple users with wireline and wireless services are simultaneously supported.......We propose and experimentally demonstrate an optical wireless DWDM system at 60 GHz with optical incoherent heterodyne up-conversion using an optical frequency comb. Multiple users with wireline and wireless services are simultaneously supported....

  3. Frequency-domain spectroscopy using high-power tunable THz-wave sources: towards THz sensing and detector sensitivity calibration

    Science.gov (United States)

    Takida, Yuma; Minamide, Hiroaki

    2017-05-01

    The development of reliable, high-power, frequency-tunable terahertz (THz)-wave sources is crucial for a wide variety of applications, such as spectroscopy, imaging, and sensing. In order to generate frequency-tunable THz waves at room temperature, one of the most promising methods is a wavelength conversion in nonlinear optical crystals. Here, we present our recent results on high-power, widely-tunable, frequency-agile THz-wave sources based on nonlinear parametric processes in MgO:LiNbO3 crystals. By changing the noncollinear phase-matching condition in MgO:LiNbO3, the tunability of sub-nanosecond-pumped injection-seeded THz-wave parametric generators (is-TPGs) covers the 3.65-octave frequency range from 0.37 THz up to 4.65 THz. The monochromatic THz-wave output from is-TPGs is greater than 10 kW peak power with the linewidth of approximately 3 GHz and the stability of 1%. These is-TPG systems are reliable and promising high-power tunable THz-wave sources for frequency-domain spectroscopic measurements towards THz sensing and detector sensitivity calibration.

  4. Optical frequency comb based multi-band microwave frequency conversion for satellite applications.

    Science.gov (United States)

    Yang, Xinwu; Xu, Kun; Yin, Jie; Dai, Yitang; Yin, Feifei; Li, Jianqiang; Lu, Hua; Liu, Tao; Ji, Yuefeng

    2014-01-13

    Based on optical frequency combs (OFC), we propose an efficient and flexible multi-band frequency conversion scheme for satellite repeater applications. The underlying principle is to mix dual coherent OFCs with one of which carrying the input signal. By optically channelizing the mixed OFCs, the converted signal in different bands can be obtained in different channels. Alternatively, the scheme can be configured to generate multi-band local oscillators (LO) for widely distribution. Moreover, the scheme realizes simultaneous inter- and intra-band frequency conversion just in a single structure and needs only three frequency-fixed microwave sources. We carry out a proof of concept experiment in which multiple LOs with 2 GHz, 10 GHz, 18 GHz, and 26 GHz are generated. A C-band signal of 6.1 GHz input to the proposed scheme is successfully converted to 4.1 GHz (C band), 3.9 GHz (C band) and 11.9 GHz (X band), etc. Compared with the back-to-back (B2B) case measured at 0 dBm input power, the proposed scheme shows a 9.3% error vector magnitude (EVM) degradation at each output channel. Furthermore, all channels satisfy the EVM limit in a very wide input power range.

  5. Zero-Forcing Frequency-Domain Equalization for Generalized DMT Transceivers with Insufficient Guard Interval

    Directory of Open Access Journals (Sweden)

    Trautmann Steffen

    2004-01-01

    Full Text Available We propose a zero-forcing frequency domain block equalizer for discrete multitone (DMT systems with a guard interval of insufficient length. In addition to the insufficient guard interval in the time domain, the equalizer takes advantage of frequency domain redundancy in the form of subcarriers that do not transmit any data. After deriving sufficient conditions for zero-forcing equalization, that is, complete removal of intersymbol and intercarrier interference, we calculate the noise enhancement of the equalizer by evaluating the signal-to-noise ratio (SNR for each subcarrier. The SNRs are used by an adaptive loading algorithm. It decides how many bits are assigned to each subcarrier in order to achieve a maximum data rate at a fixed error probability. We show that redundancy in the time domain can be traded off for redundancy in the frequency domain resulting in a transceiver with a lower system latency time. The derived equalizer matrix is sparse, thus resulting in a low computational complexity.

  6. Three-dimensional photonic metamaterials at optical frequencies.

    Science.gov (United States)

    Liu, Na; Guo, Hongcang; Fu, Liwei; Kaiser, Stefan; Schweizer, Heinz; Giessen, Harald

    2008-01-01

    Metamaterials are artificially structured media with unit cells much smaller than the wavelength of light. They have proved to possess novel electromagnetic properties, such as negative magnetic permeability and negative refractive index. This enables applications such as negative refraction, superlensing and invisibility cloaking. Although the physical properties can already be demonstrated in two-dimensional (2D) metamaterials, the practical applications require 3D bulk-like structures. This prerequisite has been achieved in the gigahertz range for microwave applications owing to the ease of fabrication by simply stacking printed circuit boards. In the optical domain, such an elegant method has been the missing building block towards the realization of 3D metamaterials. Here, we present a general method to manufacture 3D optical (infrared) metamaterials using a layer-by-layer technique. Specifically, we introduce a fabrication process involving planarization, lateral alignment and stacking. We demonstrate stacked metamaterials, investigate the interaction between adjacent stacked layers and analyse the optical properties of stacked metamaterials with respect to an increasing number of layers.

  7. Frequency Domain Packet Scheduling Under Fractional Load for the UTRAN LTE Downlink

    DEFF Research Database (Denmark)

    Pokhariyal, Akhilesh; Monghal, Guillaume Damien; Pedersen, Klaus I.

    2007-01-01

     In this paper we investigate performance of frequency domain packet scheduling (FDPS) under fractional load (FL), based on the UTRAN Long Term Evolution downlink. FL may be regarded as an inter-cell interference (ICI) mitigation technique, which can improve the user experienced SINR. We consider...

  8. Nonlinear wave equation in frequency domain: accurate modeling of ultrafast interaction in anisotropic nonlinear media

    DEFF Research Database (Denmark)

    Guo, Hairun; Zeng, Xianglong; Zhou, Binbin

    2013-01-01

    We interpret the purely spectral forward Maxwell equation with up to third-order induced polarizations for pulse propagation and interactions in quadratic nonlinear crystals. The interpreted equation, also named the nonlinear wave equation in the frequency domain, includes quadratic and cubic...

  9. Frequency domain volume rendering by the wavelet X-ray transform

    NARCIS (Netherlands)

    Westenberg, Michel A.; Roerdink, Jos B.T.M.

    2000-01-01

    We describe a wavelet-based X-ray rendering method in the frequency domain with a smaller time complexity than wavelet splatting. Standard Fourier volume rendering is summarized and interpolation and accuracy issues are briefly discussed. We review the implementation of the fast wavelet transform in

  10. Dynamic factor analysis in the frequency domain: causal modeling of multivariate psychophysiological time series

    NARCIS (Netherlands)

    Molenaar, P.C.M.

    1987-01-01

    Outlines a frequency domain analysis of the dynamic factor model and proposes a solution to the problem of constructing a causal filter of lagged factor loadings. The method is illustrated with applications to simulated and real multivariate time series. The latter applications involve topographic a

  11. Modeling of Nanophotonic Resonators with the Finite-Difference Frequency-Domain Method

    DEFF Research Database (Denmark)

    Ivinskaya, Aliaksandra; Lavrinenko, Andrei; Shyroki, Dzmitry

    2011-01-01

    Finite-difference frequency-domain method with perfectly matched layers and free-space squeezing is applied to model open photonic resonators of arbitrary morphology in three dimensions. Treating each spatial dimension independently, nonuniform mesh of continuously varying density can be built ea...

  12. Modal Identification of Output-Only Systems using Frequency Domain Decomposition

    DEFF Research Database (Denmark)

    Brincker, Rune; Zhang, L.; Andersen, P.

    2000-01-01

    In this paper a new frequency domain technique is introduced for the modal identification from ambient responses, ie. in the case where the modal parameters must be estimated without knowing the input exciting the system. By its user friendliness the technique is closely related to the classical ...

  13. Frequency-Domain Green's Functions for Radar Waves in Heterogeneous 2.5D Media

    Science.gov (United States)

    Green’s functions for radar waves propagating in heterogeneous media may be calculated in the frequency domain using a hybrid of two numerical methods. The model is defined in the Cartesian coordinate system, and its electromagnetic properties may vary in the x and z directions, ...

  14. Low-Bandwidth Channel Quality Indication for OFDMA Frequency Domain Packet Scheduling

    DEFF Research Database (Denmark)

    Kolding, Troels E.; Frederiksen, Frank; Pokhariyal, Akhilesh

    2007-01-01

     In this paper, we study methods for lowering the bandwidth needed for the UE to transmit channel quality indication (CQI) for time and frequency domain scheduling (FDPS) in OFDMA. We consider smart compression methods, such as threshold based indication, to only include scheduler...

  15. Frequency-Domain Thermal Modelling and Characterization of Power Semiconductor Devices

    DEFF Research Database (Denmark)

    Ma, Ke; He, Ning; Liserre, Marco

    2016-01-01

    their limits to correctly predict the device temperatures, especially when considering the thermal grease and heat sink attached to the power semiconductor devices. In this paper, frequency-domain approach is applied to the modelling of the thermal dynamics for power devices. The limits of the existing RC lump...

  16. Comparison between time-and frequency-domain induced polarisation parameters

    CSIR Research Space (South Africa)

    Van Schoor, Abraham M

    2009-09-01

    Full Text Available of mineralised rocks and of the contrast between different rock types. It is further shown that a multi-frequency (spectral) approach can be used to avoid this pitfall; similarly, the calculation of different time-domain induced polarisation (IP) parameters...

  17. Combination of a spinning disc confocal unit with frequency-domain fluorescence lifetime imaging microscopy.

    NARCIS (Netherlands)

    van Munster, E.B.; Goedhart, J.; Kremers, G.J.; Manders, E.M.M.; Gadella, Th.W.J.

    2007-01-01

    BACKGROUND: Wide-field frequency-domain fluorescence lifetime imaging microscopy (FLIM) is an established technique to determine fluorescence lifetimes. Disadvantage of wide-field imaging is that measurements are compromised by out-of-focus blur. Conventional scanning confocal typically means long

  18. Plastique: A synchrotron radiation beamline for time resolved fluorescence in the frequency domain

    Science.gov (United States)

    De Stasio, Gelsomina; Zema, N.; Antonangeli, F.; Savoia, A.; Parasassi, T.; Rosato, N.

    1991-06-01

    PLASTIQUE is the only synchrotron radiation beamline in the world that performs time resolved fluorescence experiments in frequency domain. These experiments are extremely valuable sources of information on the structure and dynamics of molecules. We describe the beamline and some initial data.

  19. Postural Analysis in Time and Frequency Domains in Patients with Ehlers-Danlos Syndrome

    Science.gov (United States)

    Galli, Manuela; Rigoldi, Chiara; Celletti, Claudia; Mainardi, Luca; Tenore, Nunzio; Albertini, Giorgio; Camerota, Filippo

    2011-01-01

    The goal of this work is to analyze postural control in Ehlers-Danlos syndrome (EDS) participants in time and frequency domain. This study considered a pathological group composed by 22 EDS participants performing a postural test consisting in maintaining standing position over a force platform for 30 s in two conditions: open eyes (OE) and closed…

  20. Using Enhanced Frequency Domain Decomposition as a Robust Technique to Harmonic Excitation in Operational Modal Analysis

    DEFF Research Database (Denmark)

    Jacobsen, Niels-Jørgen; Andersen, Palle; Brincker, Rune

    2006-01-01

    Enhanced Frequency Domain Decomposition technique for eliminating the influence of these harmonic components in the modal parameter extraction process. For various experiments, the quality of the method is assessed and compared to the results obtained using broadband stochastic excitation forces. Good...

  1. Joint AVO inversion in the time and frequency domain with Bayesian interference

    Science.gov (United States)

    Zong, Zhao-Yun; Yin, Xing-Yao; Li, Kun

    2016-12-01

    Amplitude variations with offset or incident angle (AVO/AVA) inversion are typically combined with statistical methods, such as Bayesian inference or deterministic inversion. We propose a joint elastic inversion method in the time and frequency domain based on Bayesian inversion theory to improve the resolution of the estimated P- and S-wave velocities and density. We initially construct the objective function using Bayesian inference by combining seismic data in the time and frequency domain. We use Cauchy and Gaussian probability distribution density functions to obtain the prior information for the model parameters and the likelihood function, respectively. We estimate the elastic parameters by solving the initial objective function with added model constraints to improve the inversion robustness. The results of the synthetic data suggest that the frequency spectra of the estimated parameters are wider than those obtained with conventional elastic inversion in the time domain. In addition, the proposed inversion approach offers stronger antinoising compared to the inversion approach in the frequency domain. Furthermore, results from synthetic examples with added Gaussian noise demonstrate the robustness of the proposed approach. From the real data, we infer that more model parameter details can be reproduced with the proposed joint elastic inversion.

  2. Differentiating Mild Papilledema and Buried Optic Nerve Head Drusen Using Spectral Domain Optical Coherence Tomography

    Science.gov (United States)

    Kulkarni, Kaushal M.; Pasol, Joshua; Rosa, Potyra R.; Lam, Byron L.

    2013-01-01

    Purpose To evaluate the clinical utility of spectral domain optical coherence tomography (SD-OCT) in differentiating mild papilledema from buried optic nerve head drusen (ONHD). Design Comparative case series. Participants 16 eyes of 9 patients with ultrasound-proven buried ONHD, 12 eyes of 6 patients with less than or equal to Frisén grade 2 papilledema due to idiopathic intracranial hypertension. 2 normal fellow eyes of patients with buried ONHD were included. Methods A raster scan on the optic nerve and retinal nerve fiber layer (RNFL) thickness analysis was performed on each eye using SD-OCT. Eight eyes underwent enhanced depth imaging SD-OCT. Images were assessed qualitatively and quantitatively to identify differentiating features between buried ONHD and papilledema. Five clinicians trained with a tutorial and masked to the underlying diagnosis reviewed the SD-OCT images of each eye independently to determine the diagnosis. Main outcome measures Differences in RNFL thickness in each quadrant between the two groups, and diagnostic accuracy of five independent clinicians based on the SD-OCT images alone. Results We found no statistically significant difference in RNFL thickness between buried ONHD and papilledema in any of the four quadrants. Diagnostic accuracy among the readers was low and ranged from 50–64%. The kappa coefficient of agreement among the readers was 0.35 (95% Confidence interval: 0.19, 0.54). Conclusions SD-OCT is not clinically reliable in differentiating buried ONHD and mild papilledema. PMID:24321144

  3. Simultaneous storage of medical images in the spatial and frequency domain: A comparative study

    Directory of Open Access Journals (Sweden)

    Acharya U Rajendra

    2004-06-01

    Full Text Available Abstract Background Digital watermarking is a technique of hiding specific identification data for copyright authentication. This technique is adapted here for interleaving patient information with medical images, to reduce storage and transmission overheads. Methods The patient information is encrypted before interleaving with images to ensure greater security. The bio-signals are compressed and subsequently interleaved with the image. This interleaving is carried out in the spatial domain and Frequency domain. The performance of interleaving in the spatial, Discrete Fourier Transform (DFT, Discrete Cosine Transform (DCT and Discrete Wavelet Transform (DWT coefficients is studied. Differential pulse code modulation (DPCM is employed for data compression as well as encryption and results are tabulated for a specific example. Results It can be seen from results, the process does not affect the picture quality. This is attributed to the fact that the change in LSB of a pixel changes its brightness by 1 part in 256. Spatial and DFT domain interleaving gave very less %NRMSE as compared to DCT and DWT domain. Conclusion The Results show that spatial domain the interleaving, the %NRMSE was less than 0.25% for 8-bit encoded pixel intensity. Among the frequency domain interleaving methods, DFT was found to be very efficient.

  4. Perturbative approach in the frequency domain for the intensity correlation spectrum in electromagnetically induced transparency

    Science.gov (United States)

    Florez, H. M.; González, C.; Martinelli, M.

    2016-07-01

    Correlation spectroscopy has been proposed as a spectroscopic technique for measuring the coherence between the ground states in electromagnetically induced transparency (EIT). While in the time domain the steep dispersion in the EIT condition accounts for the robustness of the correlation linewidth against power broadening, such physical insight was not directly established in the frequency domain. We propose a perturbative approach to describe the correlation spectroscopy of two noisy lasers coupled to a Λ transition in cold atoms, leading to EIT. Such approach leads to an analytical expression that maps the intensity correlation directly in terms of the absorption and dispersion of the light fields. Low and high perturbative regimes are investigated and demonstrate that, for coherent light sources, the first-order term in perturbation expansion represents a sufficient description for the correlation. Sideband resonances are also observed, showing the richness of the frequency domain approach.

  5. Medical Image Steganography: Study of Medical Image Quality Degradation when Embedding Data in the Frequency Domain

    Directory of Open Access Journals (Sweden)

    M.I.Khalil

    2017-02-01

    Full Text Available Steganography is the discipline of invisible communication by hiding the exchanged secret information (message in another digital information media (image, video or audio. The existence of the message is kept indiscernible in sense that no one, other than the intended recipient, suspects the existence of the message. The majority of steganography techniques are implemented either in spatial domain or in frequency domain of the digital images while the embedded information can be in the form of plain or cipher message. Medical image steganography is classified as a distinctive case of image steganography in such a way that both the image and the embedded information have special requirements such as achieving utmost clarity reading of the medical images and the embedded messages. There is a contention between the amount of hidden information and the caused detectable distortion of image. The current paper studies the degradation of the medical image when undergoes the steganography process in the frequency domain.

  6. Perturbative approach in the frequency domain for the intensity correlation spectrum at electromagnetically induced transparency

    CERN Document Server

    Florez, H M; Martinelli, M

    2016-01-01

    Correlation spectroscopy has been proposed as a spectroscopic technique for measuring the coherence between the ground states in electromagnetically induced transparency (EIT). While in time domain the steep dispersion in EIT condition accounts for the robustness of the correlation linewidth against power broadening, such physical insight was not directly established in the frequency domain. We propose a perturbative approach to describe the correlation spectroscopy of two noisy lasers coupled to a $\\Lambda$-transition in cold atoms, leading to EIT. Such approach leads to an analytical expression that maps the intensity correlation directly in terms of the absorption and dispersion of the light fields. Low and high perturbative regimes are investigated and demonstrate that, for coherent light sources, the first oder term in perturbation expansion represents a sufficient description for the correlation. Sidebands resonances are also observed, showing the richness of the frequency domain approach.

  7. Generation of frequency-chirped optical pulses with FELIX

    Science.gov (United States)

    Knippels, G. M. H.; van der Meer, A. F. G.; Mols, R. F. X. A. M.; Oepts, D.; van Amersfoort, P. W.

    1996-02-01

    By ramping the energy of the electron beam on a microsecond timescale, a frequency chirp on a picosecond timescale has been induced. The results of such an experiment are discussed as well as the results of an external pulse chirping experiment. Furthermore, the output of FELIX under normal operating conditions is investigated. For the first time a detailed series of measurements of the evolution of the optical micropulse into a train of subpulses is made when FELIX operates in the limit-cycle mode.

  8. NEW WIND-INDUCED RESPONSES ANALYSIS METHOD OF SPATIAL STRUCTURES IN FREQUENCY DOMAIN WITH MODE COMPENSATION

    Institute of Scientific and Technical Information of China (English)

    何艳丽; 董石麟

    2002-01-01

    Large span spatial lattice structures have many natural frequencies in a narrow frequency range, the conventional frequency domain method is difficult to contain all significant contribution modes. Through numerical examples, it is found that some high order modes are likely to be overlooked because of their higher positions of modal order, in spite of their significance to wind response. According to the contributions of modes to strain energy of system, the paper presented an efficient method to compensate the errors owing to missing out some significant high order modes. The effectiveness of the proposed method is verified through a numerical analysis of the wind responses of a spherical dome.

  9. Near-Zero-Refractive-Index Structure at Optical Frequencies

    Directory of Open Access Journals (Sweden)

    Hassan S. Ashour

    2013-01-01

    Full Text Available We have used a new class of left-handed materials, which uses 3D nanospheres distributed in loops in the dielectric host material. These 3D nanospheres loops give rise to negative effective permeability and permeability at Terahertz (optical frequencies. The modal dispersion relation for Terahertz TE surface waves has been derived for a slab waveguide constructed from a dielectric material slab sandwiched between two thick layers of Terahertz left-handed material (LHM. The modal dispersion relation and the power flow were numerically solved for a given set of parameters: dielectric slab thickness, the operating frequency, mode order, and the power flow and extinction in the structure. The real part of the effective refractive index exhibits near-zero values, with small extinction coefficient values. Besides that, the power flow in the dielectric core increased with slab thickness increase and the power attenuation decreased with thickness increase.

  10. Design of plasmonic toroidal metamaterials at optical frequencies.

    Science.gov (United States)

    Huang, Yao-Wei; Chen, Wei Ting; Wu, Pin Chieh; Fedotov, Vassili; Savinov, Vassili; Ho, You Zhe; Chau, Yuan-Fong; Zheludev, Nikolay I; Tsai, Din Ping

    2012-01-16

    Toroidal multipoles are the subject of growing interest because of their unusual electromagnetic properties different from the electric and magnetic multipoles. In this paper, we present two new related classes of plasmonic metamaterial composed of purposely arranged of four U-shaped split ring resonators (SRRs) that show profound resonant toroidal responses at optical frequencies. The toroidal and magnetic responses were investigated by the finite-element simulations. A phenomenon of reversed toroidal responses at higher and lower resonant frequencies has also been reported between this two related metamaterials which results from the electric and magnetic dipoles interaction. Finally, we propose a physical model based on coupled LC circuits to quantitatively analyze the coupled system of the plasmonic toroidal metamaterials.

  11. Fibre optics wavemeters calibration using a self-referenced optical frequency comb

    Science.gov (United States)

    Galindo-Santos, J.; Velasco, A. V.; Corredera, P.

    2015-01-01

    Self-referenced optical frequency combs enable the measurement of optical frequencies with a very high accuracy, achieving uncertainties close to the atomic clock used as reference (CSIC and its application to the calibration of two wavemeters in the 1.5 μm optical communication window. Calibration uncertainties down to 12 MHz and 59 MHz were obtained, respectively, for each of the devices. Furthermore, the long-term behaviour of the higher resolution wavemeter was studied during a 750 h period of sustained operation, exhibiting a dispersion in the measurements of 7.72 MHz. Temperature dependence of the device was analysed, enabling to further reduce dispersion down to a 2.15 MHz range, with no significant temporal deviations.

  12. Enhanced magnetic domain relaxation frequency and low power losses in Zn2+ substituted manganese ferrites potential for high frequency applications

    Science.gov (United States)

    Praveena, K.; Chen, Hsiao-Wen; Liu, Hsiang-Lin; Sadhana, K.; Murthy, S. R.

    2016-12-01

    Nowadays electronic industries prerequisites magnetic materials, i.e., iron rich materials and their magnetic alloys. However, with the advent of high frequency applications, the standard techniques of reducing eddy current losses, using iron cores, were no longer efficient or cost effective. Current market trends of the switched mode power supplies industries required even low energy losses in power conversion with maintenance of adequate initial permeability. From the above point of view, in the present study we aimed at the production of Manganese-Zinc ferrites prepared via solution combustion method using mixture of fuels and achieved low loss, high saturation magnetization, high permeability, and high magnetic domain relaxation frequency. The as-synthesized Zn2+ substituted MnFe2O4 were characterized by X-ray diffractometer (XRD) and transmission electron microscopy (TEM). The fractions of Mn2+, Zn2+ and Fe2+ cations occupying tetrahedral sites along with Fe occupying octahedral sites within the unit cell of all ferrite samples were estimated by Raman scattering spectroscopy. The magnetic domain relaxation was investigated by inductance spectroscopy (IS) and the observed magnetic domain relaxation frequency (fr) was increased with the increase in grain size. The real and imaginary part of permeability (μ‧ and μ″) increased with frequency and showed a maximum above 100 MHz. This can be explained on the basis of spin rotation and domain wall motion. The saturation magnetization (Ms), remnant magnetization (Mr) and magneton number (μB) decreased gradually with increasing Zn2+ concentration. The decrease in the saturation magnetization was discussed with Yafet-Kittel (Y-K) model. The Zn2+ concentration increases the relative number of ferric ions on the A sites, reduces the A-B interactions. The frequency dependent total power losses decreased as the zinc concentration increased. At 1 MHz, the total power loss (Pt) changed from 358 mW/cm3 for x=0-165 mW/cm3

  13. Fast Interrogation of Fiber Bragg Gratings with Electro-Optical Dual Optical Frequency Combs.

    Science.gov (United States)

    Posada-Roman, Julio E; Garcia-Souto, Jose A; Poiana, Dragos A; Acedo, Pablo

    2016-11-26

    Optical frequency combs (OFC) generated by electro-optic modulation of continuous-wave lasers provide broadband coherent sources with high power per line and independent control of line spacing and the number of lines. In addition to their application in spectroscopy, they offer flexible and optimized sources for the interrogation of other sensors based on wavelength change or wavelength filtering, such as fiber Bragg grating (FBG) sensors. In this paper, a dual-OFC FBG interrogation system based on a single laser and two optical-phase modulators is presented. This architecture allows for the configuration of multimode optical source parameters such as the number of modes and their position within the reflected spectrum of the FBG. A direct read-out is obtained by mapping the optical spectrum onto the radio-frequency spectrum output of the dual-comb. This interrogation scheme is proposed for measuring fast phenomena such as vibrations and ultrasounds. Results are presented for dual-comb operation under optimized control. The optical modes are mapped onto detectable tones that are multiples of 0.5 MHz around a center radiofrequency tone (40 MHz). Measurements of ultrasounds (40 kHz and 120 kHz) are demonstrated with this sensing system. Ultrasounds induce dynamic strain onto the fiber, which generates changes in the reflected Bragg wavelength and, hence, modulates the amplitude of the OFC modes within the reflected spectrum. The amplitude modulation of two counterphase tones is detected to obtain a differential measurement proportional to the ultrasound signal.

  14. Frequency domain modeling and dynamic characteristics evaluation of existing wind turbine systems

    Science.gov (United States)

    Chiang, Chih-Hung; Yu, Chih-Peng

    2016-04-01

    It is quite well accepted that frequency domain procedures are suitable for the design and dynamic analysis of wind turbine structures, especially for floating offshore wind turbines, since random wind loads and wave induced motions are most likely simulated in the frequency domain. This paper presents specific applications of an effective frequency domain scheme to the linear analysis of wind turbine structures in which a 1-D spectral element was developed based on the axially-loaded member. The solution schemes are summarized for the spectral analyses of the tower, the blades, and the combined system with selected frequency-dependent coupling effect from foundation-structure interactions. Numerical examples demonstrate that the modal frequencies obtained using spectral-element models are in good agreement with those found in the literature. A 5-element mono-pile model results in less than 0.3% deviation from an existing 160-element model. It is preliminarily concluded that the proposed scheme is relatively efficient in performing quick verification for test data obtained from the on-site vibration measurement using the microwave interferometer.

  15. The PolyMAX Frequency-Domain Method: A New Standard for Modal Parameter Estimation?

    Directory of Open Access Journals (Sweden)

    Bart Peeters

    2004-01-01

    Full Text Available Recently, a new non-iterative frequency-domain parameter estimation method was proposed. It is based on a (weighted least-squares approach and uses multiple-input-multiple-output frequency response functions as primary data. This so-called “PolyMAX” or polyreference least-squares complex frequency-domain method can be implemented in a very similar way as the industry standard polyreference (time-domain least-squares complex exponential method: in a first step a stabilisation diagram is constructed containing frequency, damping and participation information. Next, the mode shapes are found in a second least-squares step, based on the user selection of stable poles. One of the specific advantages of the technique lies in the very stable identification of the system poles and participation factors as a function of the specified system order, leading to easy-to-interpret stabilisation diagrams. This implies a potential for automating the method and to apply it to “difficult” estimation cases such as high-order and/or highly damped systems with large modal overlap. Some real-life automotive and aerospace case studies are discussed. PolyMAX is compared with classical methods concerning stability, accuracy of the estimated modal parameters and quality of the frequency response function synthesis.

  16. OPTICAL DIFFERENCE FREQUENCY GENERATION OF FAR INFRARED RADIATION

    Energy Technology Data Exchange (ETDEWEB)

    Morris, J.R.

    1977-07-01

    Three investigations of difference frequency generation (DFG) of far-infrared radiation by optical mixing are described: a theory of DFG by monochromatic, focused Gaussian pump laser beams, a theory of DFG by a picosecond pump laser pulse, and an experiment using ruby-pumped dye lasers. First, the theory of far-infrared generation by optical mixing of monochromatic, focused Gaussian beams in a uniaxial crystal is developed, taking into account the effects of diffraction, absorption, double refraction, and multiple reflections and total reflection at the boundary surfaces. (Reflection and transmission coefficients of a uniaxial crystal slab are derived by a new matrix technique.) Results of numerical calculations are presented. Focusing the pump beams appreciably enhances the far-infrared output despite the strong far-infrared diffraction. In a 1-cm long crystal, the optimum focal spot size is approximately equal to or smaller than the far-infrared wavelength for output frequencies less than 100 cm{sup -1}. Double refraction of the pump beams is relatively unimportant. Both far-infrared absorption and boundary reflections have major effects on the far-infrared output and its angular distribution. The former is often the factor which limits the output power. We show that a simple model treating the nonlinear polarization as a constant lie-radius Gaussian distribution of radiating dipoles adequately describes the effect of pump-beam focusing. We also compare the results of our calculations with those for second-harmonic generation. Second, a theoretical calculation of far-infrared power spectra generated by picosecond pulses in a nonlinear crystal is developed. The results are illustrated with two practical examples: LiNbO{sub 3} slabs oriented for rectification of the optical e-ray and for beating of the optical o-ray with the optical e-ray. The former is phase matched at 0 cm{sup -1}; the latter, at both the forward-(FCPM) and backward-collinear phase

  17. Frequency-domain characteristics of aerodynamic loads of offshore floating vertical axis wind turbines

    DEFF Research Database (Denmark)

    Borg, Michael; Collu, M.

    2015-01-01

    The re-emerging interest in vertical axis wind turbines for floating offshore applications has led to a need to investigate the relatively complex dynamics of such floating offshore structures. Through the use of a coupled model of dynamics this article investigates the frequency-domain character......The re-emerging interest in vertical axis wind turbines for floating offshore applications has led to a need to investigate the relatively complex dynamics of such floating offshore structures. Through the use of a coupled model of dynamics this article investigates the frequency-domain...... characteristics of floating vertical axis wind turbine aerodynamic loads. The impact of platform induced motion on aerodynamic loads is discussed in detail, with results indicating an increase in aerodynamic loads of several orders of magnitude over the range of frequencies usually containing significant wave...

  18. FILDIG: a program to filter brain electrical signals in the frequency domain.

    Science.gov (United States)

    Guevara, M A; Ramos, J; Hernández-González, M; Corsi-Cabrera, M

    2005-11-01

    A software program to filter brain electrical signals in the frequency domain has been developed and is presently reported. Many other filters are commercially available; however, most of them are linked to data acquisition and/or analysis programs rendering them costly. Depending on the experimental field, the full programs are not always needed. To overcome the need to obtain narrow bands in EEG research and other biological signals in an easy, fast and cheap way, we developed a computer program (FILDIG) that renders an almost ideal in-phase filter in the frequency domain and can be used in all types of personal microcomputers (PC and Mac's) and with few resources. The system uses an interactive graphic display and, with a minimum interface, it is capable of filtering multiple channels and simultaneously obtaining electrical signals (EEG, EMG, EOG, etc.) without noise or specific frequency bands.

  19. Frequency domain wave equation forward modeling using gaussian elimination with static pivoting

    Science.gov (United States)

    Jian-Yong, Song; Xiao-Dong, Zheng; Yan, Zhang; Ji-Xiang, Xu; Zhen, Qin; Xue-Juan, Song

    2011-03-01

    Frequency domain wave equation forward modeling is a problem of solving large scale linear sparse systems which is often subject to the limits of computational efficiency and memory storage. Conventional Gaussian elimination cannot resolve the parallel computation of huge data. Therefore, we use the Gaussian elimination with static pivoting (GESP) method for sparse matrix decomposition and multi-source finite-difference modeling. The GESP method does not only improve the computational efficiency but also benefit the distributed parallel computation of matrix decomposition within a single frequency point. We test the proposed method using the classic Marmousi model. Both the single-frequency wave field and time domain seismic section show that the proposed method improves the simulation accuracy and computational efficiency and saves and makes full use of memory. This method can lay the basis for waveform inversion.

  20. Numerical Calculation of Beam Coupling Impedances in the Frequency Domain using FIT

    CERN Document Server

    Niedermayer, U

    2012-01-01

    The transverse impedance of kicker magnets is considered to be one of the main beam instability sources in the projected SIS-100 at FAIR and also in the SPS at CERN. The longitudinal impedance can contribute to the heat load, which is especially a concern in the cold sections of SIS-100 and LHC. In the high frequency range, commercially available time domain codes like CST Particle Studio serve to calculate the impedance but they are inapplicable at medium and low frequencies which become more important for larger size synchrotrons. We present the ongoing work of developing a Finite Integration Technique (FIT) solver in frequency domain which is based on the Parallel and Extensible Toolkit for Scientific computing (PETSc) framework in C++. Proper beam adapted boundary conditions are important to validate the concept. The code is applied to an inductive insert used to compensate the longitudinal space charge impedance in low energy machines. Another application focuses on the impedance contribution of a ferrit...

  1. Modal identification using the frequency-scale domain decomposition technique of ambient vibration responses

    Science.gov (United States)

    Le, Thien-Phu; Argoul, Pierre

    2016-12-01

    This paper proposes a new modal identification method of ambient vibration responses. The application of the singular value decomposition to continuous wavelet transform of power spectral density matrix gives singular values and singular vectors in frequency-scale domain. Analytical development shows a direct relation between local maxima in frequency-scale representation of singular values and modal parameters. This relation is then carried on for the identification of modal parameters via a complete practical procedure. The main novelties of this work involve the new formulation in frequency-scale domain and the capacity for the identification of modal parameters without the step of ridges extraction in comparison with previous wavelet-based modal identification methods.

  2. Frequency-Domain Maximum-Likelihood Estimation of High-Voltage Pulse Transformer Model Parameters

    CERN Document Server

    Aguglia, D

    2014-01-01

    This paper presents an offline frequency-domain nonlinear and stochastic identification method for equivalent model parameter estimation of high-voltage pulse transformers. Such kinds of transformers are widely used in the pulsed-power domain, and the difficulty in deriving pulsed-power converter optimal control strategies is directly linked to the accuracy of the equivalent circuit parameters. These components require models which take into account electric fields energies represented by stray capacitance in the equivalent circuit. These capacitive elements must be accurately identified, since they greatly influence the general converter performances. A nonlinear frequency-based identification method, based on maximum-likelihood estimation, is presented, and a sensitivity analysis of the best experimental test to be considered is carried out. The procedure takes into account magnetic saturation and skin effects occurring in the windings during the frequency tests. The presented method is validated by experim...

  3. Evolutions of perturbations with special frequencies in lossless optical fibers

    Institute of Scientific and Technical Information of China (English)

    Xianqiong Zhong(钟先琼); Jianguo Chen(陈建国); Guoying Feng(冯国英); Dayi Li(李大义); Song Gao(高松)

    2004-01-01

    Expressing the perturbation optical field in terms of module and phase, using the linearized nonlinear Schrodinger equation governing the evolution of perturbations, we have deduced the analytical expressions of the modules, phases, and gain coefficients of the perturbations with zero or cut-off frequency, and studied the evolutions of the two perturbations travelling along lossless optical fibers in the negative dispersion regime. The results indicate that the phase of the perturbation with zero (or cut-off) frequency increases (or decreases) with the propagation distance monotonously and tends to its asymptotic value nπ + π/2 (or nπ) eventually. The evolution rates of the phases are closely related to the initial phase values. Although the asymptotic values of the field gain coefficients of the above mentioned two perturbations are equal to zero, and the increasing fashion of the modules is different from the familiar exponential type, it still suggests that the perturbations have a divergent nature when the propagation distance goes to infinity,indicating that the two kinds of perturbations can both lead to instability.

  4. Towards spectral-domain optical coherence tomography on a silicon chip

    NARCIS (Netherlands)

    Akça, B.I.; Nguyen, V.D.; Kalkman, J.; van Leeuwen, Ton; Worhoff, Kerstin; de Ridder, R.M.; Pollnau, Markus

    We present experimental results of a spectral-domain optical coherence tomography system that includes an integrated spectrometer. A depth range of 1 mm and axial resolution of 19 μm was measured. A layered phantom was imaged.

  5. Building the analytical response in frequency domain of AC biased bolometers Application to Planck/HFI

    CERN Document Server

    Sauvé, Alexandre

    2016-01-01

    Context: Bolometers are high sensitivity detector commonly used in Infrared astronomy. The HFI instrument of the Planck satellite makes extensive use of them, but after the satellite launch two electronic related problems revealed critical. First an unexpected excess response of detectors at low optical excitation frequency for {\

  6. BPSK optical mm-wave signal generation by septupling frequency via a single optical phase modulator

    Science.gov (United States)

    Wu, Peng; Ma, Jianxin

    2016-09-01

    In this paper, we have proposed a novel and simple scheme to generate the BPSK optical millimeter wave (MMW) signal with frequency septupling by using an optical phase modulator (PM) and a wavelength selective switch (WSS). In this scheme, the PM is driven by a radio frequency (RF) BPSK signal at the optimized modulation index of 4.89 to assure the 4th and 3rd-order sidebands have equal amplitudes. An wavelength selective switch (WSS) is used to abstract the -4th and +3rd-order sidebands from the spectrum generated by RF BPSK signal modulating the lightwave to form the BPSK optical MMW signal with frequency septupling the driving RF signal. In these two tones, only the +3rd-order sideband bears the BPSK signal while the -4th-order sideband is unmodulated since the phase information is canceled by the even times multiplication of the phase of BPSK signal. The MMW signal can avoid the pulse walk-off effect and the amplitude fading effect caused by the fiber chromatic dispersion. By adjusting the modulation index to assure the two tones have equal amplitude, the generated optical MMW signal has the maximal opto-electrical conversion efficiency and good transmission performance.

  7. Vibration sensing in flexible structures using a distributed-effect modal domain optical fiber sensor

    Science.gov (United States)

    Reichard, Karl M.; Lindner, Douglas K.; Claus, Richard O.

    1991-01-01

    Modal domain optical fiber sensors have recently been employed in the implementation of system identification algorithms and the closed-loop control of vibrations in flexible structures. The mathematical model of the modal domain optical fiber sensor used in these applications, however, only accounted for the effects of strain in the direction of the fiber's longitudinal axis. In this paper, we extend this model to include the effects of arbitrary stress. Using this sensor model, we characterize the sensor's sensitivity and dynamic range.

  8. Estimation of tire-road friction coefficient based on frequency domain data fusion

    Science.gov (United States)

    Chen, Long; Luo, Yugong; Bian, Mingyuan; Qin, Zhaobo; Luo, Jian; Li, Keqiang

    2017-02-01

    Due to the noise of sensing equipment, the tire states, such as the sideslip angle and the slip ratio, cannot be accurately observed under the conditions with small acceleration, which results in the inapplicability of the time domain data based tire-road friction coefficient (TRFC) estimation method. In order to overcome this shortcoming, frequency domain data fusion is proposed to estimate the TRFC based on the natural frequencies of the steering system and the in-wheel motor driving system. Firstly, a relationship between TRFC and the steering system natural frequency is deduced by investigating its frequency response function (FRF). Then the lateral TRFC is determined by the steering natural frequency which is only identified using the information of the assist motor current and the steering speed of the column. With spectral comparison between the steering and driving systems, the data fusion is carried out to get a comprehensive TRFC result, using the different frequency information of the longitudinal and lateral value. Finally, simulations and experiments on different road surfaces validated the correctness of the steering system FRF and the effectiveness of the proposed approach.

  9. Bilateral collicular interaction: modulation of auditory signal processing in frequency domain.

    Science.gov (United States)

    Cheng, L; Mei, H-X; Tang, J; Fu, Z-Y; Jen, P H-S; Chen, Q-C

    2013-04-01

    In the ascending auditory pathway, the inferior colliculus (IC) receives and integrates excitatory and inhibitory inputs from a variety of lower auditory nuclei, intrinsic projections within the IC, contralateral IC through the commissure of the IC and the auditory cortex. All these connections make the IC a major center for subcortical temporal and spectral integration of auditory information. In this study, we examine bilateral collicular interaction in the modulation of frequency-domain signal processing of mice using electrophysiological recording and focal electrical stimulation. Focal electrical stimulation of neurons in one IC produces widespread inhibition and focused facilitation of responses of neurons in the other IC. This bilateral collicular interaction decreases the response magnitude and lengthens the response latency of inhibited IC neurons but produces an opposite effect on the response of facilitated IC neurons. In the frequency domain, the focal electrical stimulation of one IC sharpens or expands the frequency tuning curves (FTCs) of neurons in the other IC to improve frequency sensitivity and the frequency response range. The focal electrical stimulation also produces a shift in the best frequency (BF) of modulated IC (ICMdu) neurons toward that of electrically stimulated IC (ICES) neurons. The degree of bilateral collicular interaction is dependent upon the difference in the BF between the ICES neurons and ICMdu neurons. These data suggest that bilateral collicular interaction is a part of dynamic acoustic signal processing that adjusts and improves signal processing as well as reorganizes collicular representation of signal parameters according to the acoustic experience.

  10. Time domain analysis of nonlinear frequency mixing in a slender beam for localizing a breathing crack

    Science.gov (United States)

    Joglekar, D. M.; Mitra, Mira

    2017-02-01

    The nonlinear interaction of a dual frequency flexural wave with a breathing crack generates a peculiar frequency mixing phenomena, which is manifested in form of the side bands or peaks at combinations frequencies in frequency spectrum of the response. Although these peaks have been proven useful in ascertaining the presence of crack, they barely carry any information about the crack location. In this regards, the present article analyzes the time domain representation of the response obtained by employing a wavelet spectral finite element method. The study reveals that the combination tones generated at the crack location travel with dissimilar speeds along the waveguide, owing to its dispersive nature. The separation between the lobes corresponding to these combination tones therefore, depends on the distance that they have travelled. This observation is then used to formulate a method to predict the crack location with respect to the sensor. A brief parametric study shows marginal errors in predicting the crack location, which ascertains the validity of the method. This article also studies the frequency spectrum of the response. The peaks at combination tones are quantified in terms of a modulate parameter which depends on the severity of the crack. The inferences drawn from the time and the frequency domain study can be instrumental in designing a robust strategy for detecting location and severity of the crack.

  11. Observation of a different birefringence order at optical and THz frequencies in LBO crystal

    Science.gov (United States)

    Andreev, Yu. M.; Kokh, A. E.; Kokh, K. A.; Lanskii, G. V.; Litvinenko, K.; Mamrashev, A. A.; Molloy, J. F.; Murdin, B.; Naftaly, M.; Nikolaev, N. A.; Svetlichnyi, V. A.

    2017-04-01

    THz optical properties of lithium borate (LBO) crystals were measured using time-domain spectroscopy (TDS). The LBO crystal samples were of high optical quality and were cut and polished along the , and axes. Two independent measurements were performed in order to confirm the reproducibility and consistency of results. The contradictions in the previously published data on the THz optical properties of LBO were clarified. It was shown that the birefringence order at THz frequencies is nz nx nx frequencies up to 0.5 THz for a wave polarized parallel to the Z-axis. A set of new dispersion equations was designed for the entire transparency range.

  12. Monitoring of interaction of low-frequency electric field with biological tissues upon optical clearing with optical coherence tomography

    Science.gov (United States)

    Peña, Adrián F.; Doronin, Alexander; Tuchin, Valery V.; Meglinski, Igor

    2014-08-01

    The influence of a low-frequency electric field applied to soft biological tissues ex vivo at normal conditions and upon the topical application of optical clearing agents has been studied by optical coherence tomography (OCT). The electro-kinetic response of tissues has been observed and quantitatively evaluated by the double correlation OCT approach, utilizing consistent application of an adaptive Wiener filtering and Fourier domain correlation algorithm. The results show that fluctuations, induced by the electric field within the biological tissues are exponentially increased in time. We demonstrate that in comparison to impedance measurements and the mapping of the temperature profile at the surface of the tissue samples, the double correlation OCT approach is much more sensitive to the changes associated with the tissues' electro-kinetic response. We also found that topical application of the optical clearing agent reduces the tissues' electro-kinetic response and is cooling the tissue, thus reducing the temperature induced by the electric current by a few degrees. We anticipate that dcOCT approach can find a new application in bioelectrical impedance analysis and monitoring of the electric properties of biological tissues, including the resistivity of high water content tissues and its variations.

  13. Spectral-domain optical coherence tomography on a silicon chip

    NARCIS (Netherlands)

    Akca, Bakiye Imran

    2012-01-01

    Optical coherence tomography (OCT) is a non-invasive optical technique for high-resolution cross-sectional imaging of specimens, with many applications in clinical medicine and industry (e.g. materials testing, quality assurance, and process control). Current state-of-the-art OCT systems operate in

  14. Cancellation of Fabry-Perot interference effects in terahertz time-domain spectroscopy of optically thin samples

    Science.gov (United States)

    Fastampa, Renato; Pilozzi, Laura; Missori, Mauro

    2017-06-01

    Terahertz time-domain spectroscopy is increasingly used in many fields of research. For strongly absorbing materials with refraction index close to 1, optical parameters at terahertz frequencies are most conveniently quantified using transmission measurements through thin samples. Unfortunately, extracting optical parameters from raw data implies the use and/or development of complicated numerical data processing procedures. In this work we present an efficient computational procedure for extracting the optical parameters in very thin samples (≲100 μ m) from transmission terahertz time-domain spectroscopy. In our procedure, we are able to successfully remove from raw data the Fabry-Perot interference effects, which are commonly recognized to be the leading cause of inaccuracy in the extracted parameters, introducing fictitious oscillations in their frequency dependence. The procedure is based on the Davidenko method to identify the roots of complex functions used to numerically solve the implicit equation obtained by equating the experimental and theoretical transfer functions. The advantage of the method is the possibility of obtaining the roots using the numerical solution of a system of real differential equations using standard mathematical packages. In addition, we show that complete removal of the Fabry-Perot oscillations is achieved by including in the computational procedure, besides the sample thickness, the instrumental error on the starting instant of the terahertz signal sampling. This error could be common to many terahertz time-domain systems, especially those using optical fibers. This correction is necessary in general to preserve the terahertz spectroscopic features in the extracted optical parameters for strongly absorbing materials with refraction index close to 1, such as water, biological matter, and several organic materials.

  15. Linearized Aeroelastic Computations in the Frequency Domain Based on Computational Fluid Dynamics

    CERN Document Server

    Amsallem, David; Choi, Youngsoo; Farhat, Charbel

    2015-01-01

    An iterative, CFD-based approach for aeroelastic computations in the frequency domain is presented. The method relies on a linearized formulation of the aeroelastic problem and a fixed-point iteration approach and enables the computation of the eigenproperties of each of the wet aeroelastic eigenmodes. Numerical experiments on the aeroelastic analysis and design optimization of two wing configurations illustrate the capability of the method for the fast and accurate aeroelastic analysis of aircraft configurations and its advantage over classical time-domain approaches.

  16. Frequency-domain imaging algorithm for ultrasonic testing by application of matrix phased arrays

    Directory of Open Access Journals (Sweden)

    Dolmatov Dmitry

    2017-01-01

    Full Text Available Constantly increasing demand for high-performance materials and systems in aerospace industry requires advanced methods of nondestructive testing. One of the most promising methods is ultrasonic imaging by using matrix phased arrays. This technique allows to create three-dimensional ultrasonic imaging with high lateral resolution. Further progress in matrix phased array ultrasonic testing is determined by the development of fast imaging algorithms. In this article imaging algorithm based on frequency domain calculations is proposed. This approach is computationally efficient in comparison with time domain algorithms. Performance of the proposed algorithm was tested via computer simulations for planar specimen with flat bottom holes.

  17. Simulation of power fluctuation of wind farms based on frequency domain

    DEFF Research Database (Denmark)

    Lin, Jin; Sun, Yuanzhang; Li, Guojie

    2011-01-01

    With the capacity of installed wind power generators steadily increasing in China, power fluctuation from wind farms will significantly affect the security and reliability of the power system. Traditional modeling of power fluctuation is based on the time domain or statistics methodology which...... the power spectral density of wind speed, the frequency domain model of a wind power generator and the information on weather and geography of the wind farms. The correctness and effectiveness of the model are verified by comparing the measurement data with simulation results of a certain wind farm. © 2011...

  18. Direct observation of low frequency confined acoustic phonons in silver nanoparticles: Terahertz time domain spectroscopy.

    Science.gov (United States)

    Kumar, Sunil; Kamaraju, N; Karthikeyan, B; Tondusson, M; Freysz, E; Sood, A K

    2010-07-01

    Terahertz time domain spectroscopy has been used to study low frequency confined acoustic phonons of silver nanoparticles embedded in poly(vinyl alcohol) matrix in the spectral range of 0.1-2.5 THz. The real and imaginary parts of the dielectric function show two bands at 0.60 and 2.12 THz attributed to the spheroidal and toroidal modes of silver nanoparticles, thus demonstrating the usefulness of terahertz time domain spectroscopy as a complementary technique to Raman spectroscopy in characterizing the nanoparticles.

  19. 2.5-D frequency-domain viscoelastic wave modelling using finite-element method

    Science.gov (United States)

    Zhao, Jian-guo; Huang, Xing-xing; Liu, Wei-fang; Zhao, Wei-jun; Song, Jian-yong; Xiong, Bin; Wang, Shang-xu

    2017-10-01

    2-D seismic modelling has notable dynamic information discrepancies with field data because of the implicit line-source assumption, whereas 3-D modelling suffers from a huge computational burden. The 2.5-D approach is able to overcome both of the aforementioned limitations. In general, the earth model is treated as an elastic material, but the real media is viscous. In this study, we develop an accurate and efficient frequency-domain finite-element method (FEM) for modelling 2.5-D viscoelastic wave propagation. To perform the 2.5-D approach, we assume that the 2-D viscoelastic media are based on the Kelvin-Voigt rheological model and a 3-D point source. The viscoelastic wave equation is temporally and spatially Fourier transformed into the frequency-wavenumber domain. Then, we systematically derive the weak form and its spatial discretization of 2.5-D viscoelastic wave equations in the frequency-wavenumber domain through the Galerkin weighted residual method for FEM. Fixing a frequency, the 2-D problem for each wavenumber is solved by FEM. Subsequently, a composite Simpson formula is adopted to estimate the inverse Fourier integration to obtain the 3-D wavefield. We implement the stiffness reduction method (SRM) to suppress artificial boundary reflections. The results show that this absorbing boundary condition is valid and efficient in the frequency-wavenumber domain. Finally, three numerical models, an unbounded homogeneous medium, a half-space layered medium and an undulating topography medium, are established. Numerical results validate the accuracy and stability of 2.5-D solutions and present the adaptability of finite-element method to complicated geographic conditions. The proposed 2.5-D modelling strategy has the potential to address modelling studies on wave propagation in real earth media in an accurate and efficient way.

  20. Automatic analysis of ciliary beat frequency using optical flow

    Science.gov (United States)

    Figl, Michael; Lechner, Manuel; Werther, Tobias; Horak, Fritz; Hummel, Johann; Birkfellner, Wolfgang

    2012-02-01

    Ciliary beat frequency (CBF) can be a useful parameter for diagnosis of several diseases, as e.g. primary ciliary dyskinesia. (PCD). CBF computation is usually done using manual evaluation of high speed video sequences, a tedious, observer dependent, and not very accurate procedure. We used the OpenCV's pyramidal implementation of the Lukas-Kanade algorithm for optical flow computation and applied this to certain objects to follow the movements. The objects were chosen by their contrast applying the corner detection by Shi and Tomasi. Discrimination between background/noise and cilia by a frequency histogram allowed to compute the CBF. Frequency analysis was done using the Fourier transform in matlab. The correct number of Fourier summands was found by the slope in an approximation curve. The method showed to be usable to distinguish between healthy and diseased samples. However there remain difficulties in automatically identifying the cilia, and also in finding enough high contrast cilia in the image. Furthermore the some of the higher contrast cilia are lost (and sometimes found) by the method, an easy way to distinguish the correct sub-path of a point's path have yet to be found in the case where the slope methods doesn't work.

  1. High-frequency signal generation using 1550 nm VCSEL subject to two-frequency optical injection

    Science.gov (United States)

    Consoli, Antonio; Quirce, Ana; Valle, Angel; Esquivias, Ignacio; Pesquera, Luis; García Tijero, Jose Manuel

    2013-03-01

    We experimentally investigate high-frequency microwave signal generation using a 1550 nm single-mode VCSEL subject to two-frequency optical injection. We first consider a situation in which the injected signals come from two similar VCSELs. The polarization of the injected light is parallel to that of the injected VCSEL. We obtain that the VCSEL can be locked to one of the injected signals, but the observed microwave signal is originated by beating at the photodetector. In a second situation we consider injected signals that come from two external cavity tunable lasers with a significant increase of the injected power with respect to the VCSEL-by-VCSEL injection case. The polarization of the injected light is orthogonal to that of the free-running slave VCSEL. We show that in this case it is possible to generate a microwave signal inside the VCSEL cavity.

  2. Signal line shapes of Fourier transform cavity-enhanced frequency modulation spectroscopy with optical frequency combs

    CERN Document Server

    Johansson, Alexandra C; Khodabakhsh, Amir; Foltynowicz, Aleksandra

    2016-01-01

    We present a thorough analysis of the signal line shapes of Fourier transform-based noise-immune cavity-enhanced optical frequency comb spectroscopy (NICE-OFCS). We discuss the signal dependence on the ratio of the modulation frequency, f${_m}$, to the molecular line width, {\\Gamma}. We compare a full model of the signals and a simplified absorption-like analytical model that has high accuracy for low f${_m}$/{\\Gamma} ratios and is much faster to compute. We verify the theory experimentally by measuring and fitting NICE-OFCS spectra of CO${_2}$ at 1575 nm using a system based on an Er:fiber femtosecond laser and a cavity with a finesse of ~11000.

  3. Noninvasive assessment of testicular torsion in rabbits using frequency-domain near-infrared spectroscopy: prospects for pediatric urology

    Science.gov (United States)

    Hallacoglu, Bertan; Matulewicz, Richard S.; Paltiel, Harriet J.; Padua, Horacio; Gargollo, Patricio; Cannon, Glenn; Alomari, Ahmad; Sassaroli, Angelo; Fantini, Sergio

    2009-09-01

    We present a quantitative near-IR spectroscopy study of the absolute values of oxygen saturation of hemoglobin before and after surgically induced testicular torsion in adult rabbits. Unilateral testicular torsions (0, 540, or 720 deg) on experimental testes and contralateral sham surgery on control testes are performed in four adult rabbits. A specially designed optical probe for measurements at multiple source-detector distances and a commercial frequency-domain tissue spectrometer are used to measure absolute values of testicular hemoglobin saturation. Our results show: (1) a consistent baseline absolute tissue hemoglobin saturation value of 78+/-5%, (2) a comparable tissue hemoglobin saturation of 77+/-6% after sham surgery, and (3) a significantly lower tissue hemoglobin saturation of 36+/-2% after 540- and 720-deg testicular torsion surgery. Our findings demonstrate the feasibility of performing frequency-domain, multidistance near-IR spectroscopy for absolute testicular oximetry in the assessment of testicular torsion. We conclude that near-IR spectroscopy has potential to serve as a clinical diagnostic and monitoring tool for the assessment of absolute testicular hemoglobin desaturation caused by torsion, with the possibility of serving as a complement to conventional color and spectral Doppler ultrasonography.

  4. Modal domain fiber optic sensor for closed loop vibration control of a flexible beam

    Science.gov (United States)

    Cox, D.; Thomas, D.; Reichard, K.; Lindner, D.; Claus, R. O.

    1990-01-01

    The use of a modal domain sensor in a vibration control experiment is described. An optical fiber is bonded along the length of a flexible beam. A control signal derived from the output of the modal domain sensor is used to suppress vibrations induced in the beam. A distributed effect model for the modal domain sensor is developed and combined with models of the beam and actuator dynamics to produce a system suitable for control design.

  5. Measuring absolute frequencies beyond the GPS limit via long-haul optical frequency dissemination

    CERN Document Server

    Clivati, C; Livi, L; Poggiali, F; de Cumis, M Siciliani; Mancini, M; Pagano, G; Frittelli, M; Mura, A; Costanzo, G A; Levi, F; Calonico, D; Fallani, L; Catani, J; Inguscio, M

    2015-01-01

    Global Positioning System (GPS) dissemination of frequency standards is ubiquitous at present, providing the most widespread time and frequency reference for the majority of industrial and research applications worldwide. On the other hand, the ultimate limits of the GPS presently curb further advances in high-precision, scientific and industrial applications relying on this dissemination scheme. Here, we demonstrate that these limits can be reliably overcome even in laboratories without a local atomic clock by replacing the GPS with a 642-km-long optical fiber link to a remote primary caesium frequency standard. Through this configuration we stably address the $^1$S$_0$---$^3$P$_0$ clock transition in an ultracold gas of $^{173}$Yb, with a precision that exceeds the possibilities of a GPS-based measurement, dismissing the need for a local clock infrastructure to perform high-precision tasks beyond GPS limit. We also report an improvement of two orders of magnitude in the accuracy on the transition frequency ...

  6. Permutation Correction in the Frequency Domain in Blind Separation of Speech Mixtures

    Directory of Open Access Journals (Sweden)

    Pham DT

    2006-01-01

    Full Text Available This paper presents a method for blind separation of convolutive mixtures of speech signals, based on the joint diagonalization of the time varying spectral matrices of the observation records. The main and still largely open problem in a frequency domain approach is permutation ambiguity. In an earlier paper of the authors, the continuity of the frequency response of the unmixing filters is exploited, but it leaves some frequency permutation jumps. This paper therefore proposes a new method based on two assumptions. The frequency continuity of the unmixing filters is still used in the initialization of the diagonalization algorithm. Then, the paper introduces a new method based on the time-frequency representations of the sources. They are assumed to vary smoothly with frequency. This hypothesis of the continuity of the time variation of the source energy is exploited on a sliding frequency bandwidth. It allows us to detect the remaining frequency permutation jumps. The method is compared with other approaches and results on real world recordings demonstrate superior performances of the proposed algorithm.

  7. Rolling element bearing faults diagnosis based on kurtogram and frequency domain correlated kurtosis

    Science.gov (United States)

    Gu, Xiaohui; Yang, Shaopu; Liu, Yongqiang; Hao, Rujiang

    2016-12-01

    Envelope analysis is one of the most useful methods in localized fault diagnosis of rolling element bearings. However, there is a challenge in selecting the optimal resonance band. In this paper, a novel method based on kurtogram and frequency domain correlated kurtosis is proposed. To obtain the correct relationship between the node and frequency band in wavelet packet transform, a vital process named frequency ordering is conducted to solve the frequency folding problem due to down sampling. Correlated kurtosis of envelope spectrum instead of correlated kurtosis of envelope signal or kurtosis of envelope spectrum is utilized to generate the kurtogram, in which the maximum value can indicate the optimal band for envelope analysis. Several cases of experimental bearing fault signals are used to evaluate the immunity of the proposed method to strong noise interference. The improved performance has also been compared with two previous developed methods. The results demonstrate the effectiveness and robustness of the method in fault diagnosis of rolling element bearings.

  8. Visco-acoustic transmission waveform inversion of velocity structure in space-frequency domain

    Institute of Scientific and Technical Information of China (English)

    Guihua Long; Xiaofan Li; Meigen Zhang; Tong Zhu

    2009-01-01

    According to the least square criterion of minimizing the misfit between modeled and observed data, this paper provides a preconditioned gradient method to invert the visco-acoustic velocity structure on the basis of using sparse matrix LU factorization technique to directly solve the visco-acoustic wave forward problem in space-frequency domain. Numerical results obtained in an inclusion model inversion and a layered homogeneous model inversion demonstrate that different scale media have their own frequency responses, and the strategy of using low-frequency inverted result as the starting model in the high-frequency inversion can greatly reduce the non-uniqueness of their solutions. It can also be observed in the experi-ments that the fast convergence of the algorithm can be achieved by using diagonal elements of Hessian matrix as the pre-conditioned operator, which fully incorporates the advantage of quadratic convergence of Gauss-Newton method.

  9. Data-Aided Frequency-Domain Channel Estimation for CD and DGD Monitoring in Coherent Transmission Systems

    DEFF Research Database (Denmark)

    Pittalà, Fabio; Hauske, Fabian N.; Ye, Yabin;

    2011-01-01

    CD and DGD monitoring from Frequency- Domain Zero-Forcing and MMSE filter functions adapted with the aid of short CAZAC training sequences is demonstrated.......CD and DGD monitoring from Frequency- Domain Zero-Forcing and MMSE filter functions adapted with the aid of short CAZAC training sequences is demonstrated....

  10. Modal Identification and Damage Detection on a Concrete Highway Bridge by Frequency Domain Decomposition

    DEFF Research Database (Denmark)

    Brincker, Rune; Andersen, Palle; Zhang, Lingmi

    2007-01-01

    As a part of a research project co-founded by the European Community, a series of 15 damage tests were performed on a prestressed concrete highway bridge in Switzerland. The ambient response of the bridge was recorded for each damage case. A dense array of instruments allowed the identification...... of a modal model with a total of 408 degrees of freedom. Six modes were identified in the frequency range from 0 to 16.7 Hz. The objective of this paper is to demonstrate the effectiveness of the Frequency Domain Decomposition (FDD) technique for modal identification of large structures. A second objective...

  11. Modal Identification and Damage Detection on a Concrete Highway Bridge by Frequency Domain Decomposition

    DEFF Research Database (Denmark)

    Brincker, Rune; Andersen, P.; Zhang, L.

    2002-01-01

    As a part of a research project co-founded by the European Community, a series of 15 damage tests were performed on a prestressed concrete highway bridge in Switzerland. The ambient response of the bridge was recorded for each damage case. A dense array of instruments allowed the identification...... of a modal model with a total of 408 degrees of freedom. Six modes were identified in the frequency range from 0 to 16.7 Hz. The objective of this paper is to demonstrate the effectiveness of the Frequency Domain Decomposition (FDD) technique for modal identification of large structures. A second objective...

  12. Investigation of Frequency-Domain Link Adaptation for a 5-MHz OFDMA/HSDPA system

    DEFF Research Database (Denmark)

    Pokhariyal, Akhilesh; Kolding, Troels E.; Frederiksen, Frank

    2005-01-01

    In this paper, we investigate frequency domain link adaptation (FDLA), e.g. utilizing the frequency selectivity of the channel in an OFDMA system. To make the study specific and based on realistic parameters, we re-use the specifications from a recent 3GPP 5-MHz OFDMA study item. The link...... find that optimum waterfilling power distribution only provides a marginal gain over a simpler on/off equal power distribution algorithm per sub-carrier pool when signaling imperfections are taken into account....

  13. Reducing Dataset Size in Frequency Domain for Brain Computer Interface Motor Imagery Classification

    Directory of Open Access Journals (Sweden)

    Ch.Aparna

    2010-12-01

    Full Text Available Brain computer interface is an emerging area of research where the BCI system is able to detect and interpret the mental activity into computer interpretable signals opening a wide area of applications where activities can be completed without using muscular movement. In Brain Computer Interface research, for classification of EEG signals the raw signals captured has to undergo some preprocessing, to obtain the right attributes for classification. In this paper, we present a system which allows for classification of mental tasks based on a statistical data obtained in frequency domain using Discrete cosine transform and extracting useful frequencies from the same with application of decision tree algorithms for classification.

  14. Time domain dispersion of underwater optical wireless communication

    Institute of Scientific and Technical Information of China (English)

    Wei Wei; Xiaohui Zhang; Jionghui Rao; Wenbo Wang

    2011-01-01

    @@ A new method to count the expected value and variance of time dispersion is presented for time dispersion of underwater optical wireless communication.Instead of the typically used Gamma distribution, inverse-Gaussian distribution is suggested for underwater optical impulse response time waveform function.The expectation of this method is in good agreement with experimental data.Future works may include water absorption to the model.%A new method to count the expected value and variance of time dispersion is presented for time dispersion of underwater optical wireless communication.Instead of the typically used Gamma distribution, inverseGaussian distribution is suggested for underwater optical impulse response time waveform function.The expectation of this method is in good agreement with experimental data.Future works may include water absorption to the model.

  15. Fast, precise, and widely tunable frequency control of an optical parametric oscillator referenced to a frequency comb

    Science.gov (United States)

    Prehn, Alexander; Glöckner, Rosa; Rempe, Gerhard; Zeppenfeld, Martin

    2017-03-01

    Optical frequency combs (OFCs) provide a convenient reference for the frequency stabilization of continuous-wave lasers. We demonstrate a frequency control method relying on tracking over a wide range and stabilizing the beat note between the laser and the OFC. The approach combines fast frequency ramps on a millisecond timescale in the entire mode-hop free tuning range of the laser and precise stabilization to single frequencies. We apply it to a commercially available optical parametric oscillator (OPO) and demonstrate tuning over more than 60 GHz with a ramping speed up to 3 GHz/ms. Frequency ramps spanning 15 GHz are performed in less than 10 ms, with the OPO instantly relocked to the OFC after the ramp at any desired frequency. The developed control hardware and software are able to stabilize the OPO to sub-MHz precision and to perform sequences of fast frequency ramps automatically.

  16. Frequency domain volume rendering by the wavelet X-ray transform.

    Science.gov (United States)

    Westenberg, M A; Roerdink, J M

    2000-01-01

    We describe a wavelet based X-ray rendering method in the frequency domain with a smaller time complexity than wavelet splatting. Standard Fourier volume rendering is summarized and interpolation and accuracy issues are briefly discussed. We review the implementation of the fast wavelet transform in the frequency domain. The wavelet X-ray transform is derived, and the corresponding Fourier-wavelet volume rendering algorithm (FWVR) is introduced, FWVR uses Haar or B-spline wavelets and linear or cubic spline interpolation. Various combinations are tested and compared with wavelet splatting (WS). We use medical MR and CT scan data, as well as a 3-D analytical phantom to assess the accuracy, time complexity, and memory cost of both FWVR and WS. The differences between both methods are enumerated.

  17. Improvement of Frequency Domain Output Only Modal Identification from the Application of the Random Decrement Technique

    DEFF Research Database (Denmark)

    Rodrigues, J.; Brincker, Rune; Andersen, P.

    2004-01-01

    from the time series, are due to the noise reduction that results from the time averaging procedure of the random decrement technique, and from avoiding leakage in the spectral densities, as long as the random decrement functions are evaluated with sufficient time length to have a complete decay within......This paper explores the idea of estimating the spectral densities as the Fourier transform of the random decrement functions for the application of frequency domain output-only modal identification methods. The gains in relation to the usual procedure of computing the spectral densities directly...... that length. The idea is applied in the analysis of ambient vibration data collected in a ¼ scale model of a 4-story building. The results show that a considerable improvement is achieved, in terms of noise reduction in the spectral density functions and corresponding quality of the frequency domain modal...

  18. Frequency domain stability analysis of nonlinear active disturbance rejection control system.

    Science.gov (United States)

    Li, Jie; Qi, Xiaohui; Xia, Yuanqing; Pu, Fan; Chang, Kai

    2015-05-01

    This paper applies three methods (i.e., root locus analysis, describing function method and extended circle criterion) to approach the frequency domain stability analysis of the fast tool servo system using nonlinear active disturbance rejection control (ADRC) algorithm. Root locus qualitative analysis shows that limit cycle is generated because the gain of the nonlinear function used in ADRC varies with its input. The parameters in the nonlinear function are adjustable to suppress limit cycle. In the process of root locus analysis, the nonlinear function is transformed based on the concept of equivalent gain. Then, frequency domain description of the nonlinear function via describing function is presented and limit cycle quantitative analysis including estimating prediction error is presented, which virtually and theoretically demonstrates that the describing function method cannot guarantee enough precision in this case. Furthermore, absolute stability analysis based on extended circle criterion is investigated as a complement.

  19. Spatial and frequency domain interferometry using the MU radar - A tutorial and recent developments

    Science.gov (United States)

    Fukao, Shoichiro; Palmer, Robert D.

    Fundamental notions of spatial and frequency-domain interferometry are reviewed, and a novel method is proposed for steering the antenna beam after the data are stored. Also presented is a comparison of techniques for wind-vector determination with emphasis given to a method based on the linear variation of the phase of the cross-spectra. Recent applications of spatial interferometry (SI) and frequency-domain interferometry (FDI) are listed including an implementation of FDI with MU radar. The vertical wind velocity estimated from the Doppler technique is shown to be a measure of the wind perpendicular to tilted refractivity surfaces. The bias generated by horizontal wind is found to have a significant effect on the Doppler estimate in SI. The use of MU radar in FDI can facilitate measurements of the positions of high reflectivity layers smaller than the resolution volume.

  20. The research on recognition and extraction of river feature in IKNOS based on frequency domain

    Science.gov (United States)

    Wang, Ke; Feng, Xuezhi; Xiao, Pengfeng; Wu, Guoping

    2009-10-01

    Because the resolution of remotely sensed imagery becomes higher, new methods are introduced to process the high-resolution remotely sensed imagery. The algorithms introduced in this paper to recognize and extract the river features based on the frequency domain. This paper uses the Gabor filter in frequency domain to enhance the texture of river and remove the noise from remotely sensed imagery. And then according to the theory of phase congruency, this paper retrieves the PC of every point such that features such as edge of river, building and farmland in the remotely sensed imagery. Lastly, the skeletal methodology is introduced to determine the edge of river within the help of the trend of river.