WorldWideScience

Sample records for operating conditions amenable

  1. Final Report - Advanced MEA's for Enhanced Operating Conditions, Amenable to High Volume Manufacture

    Energy Technology Data Exchange (ETDEWEB)

    Debe, Mark K.

    2007-09-30

    This report summarizes the work completed under a 3M/DOE contract directed at advancing the key fuel cell (FC) components most critical for overcoming the polymer electrolyte membrane fuel cell (PEMFC) performance, durability & cost barriers. This contract focused on the development of advanced ion exchange membranes & electrocatalysts for PEMFCs that will enable operation under ever more demanding automotive operating conditions & the use high volume compatible processes for their manufacture. Higher performing & more durable electrocatalysts must be developed for PEMFCs to meet the power density & lifetime hours required for FC vehicles. At the same time the amount of expensive Pt catalyst must be reduced to lower the MEA costs. While these two properties are met, the catalyst must be made resistant to multiple degradation mechanisms to reach necessary operating lifetimes. In this report, we present the work focused on the development of a completely new approach to PEMFC electrocatalyts, called nanostructured thin film (NSTF) catalysts. The carbon black supports are eliminated with this new approach which eliminates the carbon corrosion issue. The thin film nature of the catalyst significantly improves its robustness against dissolution & grain growth, preserving the surface area. Also, the activity of the NSTF for oxygen reduction is improved by over 500% compared to dispersed Pt catalyts. Finally, the process for fabricating the NSTF catalysts is consistent with high volume roll-good manufacturing & extremely flexible towards the introduction of new catalyst compositions & structures. This report documents the work done to develop new multi-element NSTF catalysts with properties that exceed pure Pt, that are optimized for use with the membranes discussed below, & advance the state-of-the-art towards meeting the DOE 2010 targets for PEMFC electrocatalysts. The work completed advances the understanding of the NSTF catalyst technology, identifies new NSTF

  2. Final Report - Advanced MEA's for Enhanced Operating Conditions, Amenable to High Volume Manufacture

    Energy Technology Data Exchange (ETDEWEB)

    Debe, Mark K.

    2007-09-30

    This report summarizes the work completed under a 3M/DOE contract directed at advancing the key fuel cell (FC) components most critical for overcoming the polymer electrolyte membrane fuel cell (PEMFC) performance, durability & cost barriers. This contract focused on the development of advanced ion exchange membranes & electrocatalysts for PEMFCs that will enable operation under ever more demanding automotive operating conditions & the use high volume compatible processes for their manufacture. Higher performing & more durable electrocatalysts must be developed for PEMFCs to meet the power density & lifetime hours required for FC vehicles. At the same time the amount of expensive Pt catalyst must be reduced to lower the MEA costs. While these two properties are met, the catalyst must be made resistant to multiple degradation mechanisms to reach necessary operating lifetimes. In this report, we present the work focused on the development of a completely new approach to PEMFC electrocatalyts, called nanostructured thin film (NSTF) catalysts. The carbon black supports are eliminated with this new approach which eliminates the carbon corrosion issue. The thin film nature of the catalyst significantly improves its robustness against dissolution & grain growth, preserving the surface area. Also, the activity of the NSTF for oxygen reduction is improved by over 500% compared to dispersed Pt catalyts. Finally, the process for fabricating the NSTF catalysts is consistent with high volume roll-good manufacturing & extremely flexible towards the introduction of new catalyst compositions & structures. This report documents the work done to develop new multi-element NSTF catalysts with properties that exceed pure Pt, that are optimized for use with the membranes discussed below, & advance the state-of-the-art towards meeting the DOE 2010 targets for PEMFC electrocatalysts. The work completed advances the understanding of the NSTF catalyst technology, identifies new NSTF

  3. Additional Conditions Amenable to Observation Care.

    Science.gov (United States)

    Wheatley, Matthew A

    2017-08-01

    ED observation units (EDOUs) are designed for patients who require diagnostics or therapeutics beyond the initial ED visit to determine the need for hospital admission. Best evidence is that this care be delivered via ordersets or protocols. Occasionally, patients present with conditions that are amenable to EDOU care but fall outside the commonly used protocols. This article details a few of these conditions: abnormal uterine bleeding, allergic reaction, alcohol intoxication, acetaminophen overdose and sickle cell vaso-occlusive crisis. It is not meant to be exhaustive as patient care needs can vary hospital to hospital. Copyright © 2017 Elsevier Inc. All rights reserved.

  4. Amenability and vanishing of L^2-Betti numbers: an operator algebraic approach

    CERN Document Server

    Alekseev, Vadim

    2011-01-01

    We recast the Foelner condition in an operator algebraic setting and prove that it implies a certain dimension flatness property. Furthermore, it is proven that the Foelner condition generalizes the existing notions of amenability and that the enveloping von Neumann algebra arising from a Foelner algebra is automatically injective. As an application we show how our techniques unify the previously known results concerning vanishing of L^2-Betti numbers for amenable groups, groupoids and quantum groups and moreover provides a large class of new examples of algebras with vanishing L^2-Betti numbers.

  5. Prevalence of Medical Conditions Potentially Amenable to Cellular Therapy among Families Privately Storing Umbilical Cord Blood.

    Science.gov (United States)

    Mazonson, Peter; Kane, Mark; Colberg, Kelin; Harris, Heather; Brown, Heather; Mohr, Andrew; Ziman, Alyssa; Santas, Chris

    2017-01-01

    Introduction Little is known about the prevalence of conditions potentially amenable to cellular therapy among families storing umbilical cord blood in private cord blood banks. Methods A cross-sectional study of families with at least one child who stored umbilical cord blood in the largest private cord blood bank in the United States was performed. Respondent families completed a questionnaire to determine whether children with stored cord blood or a first-degree relative had one or more of 16 conditions amenable primarily to allogeneic stem cell transplant ("transplant indications") or 16 conditions under investigation for autologous stem cell infusion ("regenerative indications"), regardless of whether they received a transplant or infusion. Results 94,803 families responded, representing 33.3 % of those surveyed. Of respondent families, 16.01 % indicated at least one specified condition. 1.64 % reported at least one first-degree member with a transplant indication potentially treatable with an allogeneic stem cell transplant. The most common transplant indications reported among first-degree family members were Non-Hodgkin's Lymphoma (0.33 %), Hodgkin's Lymphoma (0.30 %), and Acute Lymphoblastic Leukemia (0.28 %). 4.23 % reported at least one child with a regenerative indication potentially treatable with an autologous stem cell infusion. The most common regenerative indications among children with stored umbilical cord blood were Autism/Autism Spectrum Disorder/Apraxia (1.93 %), Other Developmental Delay (1.36 %), and Congenital Heart Defect (0.87 %). Discussion Among families storing umbilical cord blood in private cord blood banks, conditions for which stem cell transplant or infusion may be indicated, or are under investigation, appear to be prevalent, especially for regenerative medicine indications.

  6. Lectures on amenability

    CERN Document Server

    Runde, Volker

    2002-01-01

    The notion of amenability has its origins in the beginnings of modern measure theory: Does a finitely additive set function exist which is invariant under a certain group action? Since the 1940s, amenability has become an important concept in abstract harmonic analysis (or rather, more generally, in the theory of semitopological semigroups). In 1972, B.E. Johnson showed that the amenability of a locally compact group G can be characterized in terms of the Hochschild cohomology of its group algebra L^1(G): this initiated the theory of amenable Banach algebras. Since then, amenability has penetrated other branches of mathematics, such as von Neumann algebras, operator spaces, and even differential geometry. Lectures on Amenability introduces second year graduate students to this fascinating area of modern mathematics and leads them to a level from where they can go on to read original papers on the subject. Numerous exercises are interspersed in the text.

  7. Socioeconomic inequalities in mortality from conditions amenable to medical interventions: do they reflect inequalities in access or quality of health care?

    Directory of Open Access Journals (Sweden)

    Plug Iris

    2012-05-01

    Full Text Available Abstract Background Previous studies have reported large socioeconomic inequalities in mortality from conditions amenable to medical intervention, but it is unclear whether these can be attributed to inequalities in access or quality of health care, or to confounding influences such as inequalities in background risk of diseases. We therefore studied whether inequalities in mortality from conditions amenable to medical intervention vary between countries in patterns which differ from those observed for other (non-amenable causes of death. More specifically, we hypothesized that, as compared to non-amenable causes, inequalities in mortality from amenable causes are more strongly associated with inequalities in health care use and less strongly with inequalities in common risk factors for disease such as smoking. Methods Cause-specific mortality data for people aged 30–74 years were obtained for 14 countries, and were analysed by calculating age-standardized mortality rates and relative risks comparing a lower with a higher educational group. Survey data on health care use and behavioural risk factors for people aged 30–74 years were obtained for 12 countries, and were analysed by calculating age-and sex-adjusted odds ratios comparing a low with a higher educational group. Patterns of association were explored by calculating correlation coefficients. Results In most countries and for most amenable causes of death substantial inequalities in mortality were observed, but inequalities in mortality from amenable causes did not vary between countries in patterns that are different from those seen for inequalities in non-amenable mortality. As compared to non-amenable causes, inequalities in mortality from amenable causes are not more strongly associated with inequalities in health care use. Inequalities in mortality from amenable causes are also not less strongly associated with common risk factors such as smoking. Conclusions We did not find

  8. Definably amenable NIP groups

    OpenAIRE

    Chernikov, Artem; Simon, Pierre

    2015-01-01

    We study definably amenable NIP groups. We develop a theory of generics, showing that various definitions considered previously coincide, and study invariant measures. Applications include: characterization of regular ergodic measures, a proof of the conjecture of Petrykowski connecting existence of bounded orbits with definable amenability in the NIP case, and the Ellis group conjecture of Newelski and Pillay connecting the model-theoretic connected component of an NIP group with the ideal s...

  9. Operant Conditioning for Special Educators.

    Science.gov (United States)

    Pedrini, Bonnie C.; Pedrini, D. T.

    The paper briefly explains operant conditioning as it pertains to special educators. Operant conditioning is thought to be an efficient method for modifying student behavior. Using the B. F. Skinner frame of reference, operant conditioning is said to include behavior modification and therapy, programed instruction, and computer assisted and…

  10. Paranormal weighted conditional type operators

    OpenAIRE

    Estaremi, Yousef

    2014-01-01

    In this paper, some sub-classes of paranormal weighted conditional expectation type operators, such as *-paranormal, quasi-*-paranormal and (n; k)-quasi-*-paranormal weighted conditional expectation type opera- tors on $L^2(\\Sigma)$ are investigated. Also, some applications about the spectrum, point spectrum, joint point spectrum, approximate point spectrum and joint approximate point spectrum of these classes are presented.

  11. WORK CONDITIONS OF CHAINSAW OPERATORS

    Directory of Open Access Journals (Sweden)

    Jorge Roberto Malinovski

    2002-01-01

    Full Text Available The objective of this research was to analyze the human factors and the work conditions in clear-cutting operations using chainsaws in mountainous areas. Data were colected in a forestry company in Minas Gerais, Brazil, by interviews with 29 chainsaw operators. The results indicated that the operators average age was 32.3 years, height 1.68m and body weight 64.4Kg. The average job time in the company was 112 months and the average time of chainsaw operation experience was 81.5 months. Most (93.1% were dexterous and 6.9% were left-handed. The high incidence of backache (41.4% indicated that the task demands an overload of lumbar column, so that the company should take preventive measures to avoid backaches, using educational strategies or changing the opera-tional system. The high level of accidents (44.8% indicated that some precautions are needed to im-prove work safety.

  12. Amenable, transitive and faithful actions of groups acting on trees

    CERN Document Server

    Fima, Pierre

    2012-01-01

    We study under which condition an amalgamated free product or an HNN-extension over a finite subgroup admits an amenable, transitive and faithful action on an infinite countable set. We show that such an action exists if the initial groups admit an amenable and almost free action with infinite orbits (e.g. virtually free groups or infinite amenable groups). Our result relies on the Baire category Theorem. We extend the result to groups acting on trees.

  13. Dyadic data analysis with amen

    OpenAIRE

    Hoff, Peter D.

    2015-01-01

    Dyadic data on pairs of objects, such as relational or social network data, often exhibit strong statistical dependencies. Certain types of second-order dependencies, such as degree heterogeneity and reciprocity, can be well-represented with additive random effects models. Higher-order dependencies, such as transitivity and stochastic equivalence, can often be represented with multiplicative effects. The "amen" package for the R statistical computing environment provides estimation and infere...

  14. Wages, Amenities and Negative Attitudes

    DEFF Research Database (Denmark)

    Waisman, Gisela; Larsen, Birthe

    We exploit the regional variation in negative attitudes towards immigrants to Sweden in order to analyse the consequences of the attitudes on immigrants welfare. We find that attitudes towards immigrants are of importance: they both affect their labour market outcomes and their quality of life. We...... interpret the negative effect on wages as evidence of labour market discrimination. We estimate the welfare effects of negative attitudes, through their wage and local amenities, for immigrants with different levels of skills, origin, gender and age....

  15. Income, Amenities and Negative Attitudes

    DEFF Research Database (Denmark)

    Waisman, Gisela; Larsen, Birthe

    2016-01-01

    ’ quality of life, they also affect their income. We estimate the utility effects of negative attitudes for refugees with different levels of education and gender. We also analyse how the size of the refugees’ networks relate to their quality of life and income as well as how negative attitudes towards......We exploit the regional variation in negative attitudes towards immigrants to Sweden in order to analyse the consequences of negative attitudes on refugees’ utility from labour income and amenities. We find that attitudes towards immigrants are important: while they affect mainly the refugees...

  16. Condition Monitoring Of Operating Pipelines With Operational Modal Analysis Application

    Directory of Open Access Journals (Sweden)

    Mironov Aleksey

    2015-12-01

    Full Text Available In the petroleum, natural gas and petrochemical industries, great attention is being paid to safety, reliability and maintainability of equipment. There are a number of technologies to monitor, control, and maintain gas, oil, water, and sewer pipelines. The paper focuses on operational modal analysis (OMA application for condition monitoring of operating pipelines. Special focus is on the topicality of OMA for definition of the dynamic features of the pipeline (frequencies and mode shapes in operation. The research was conducted using two operating laboratory models imitated a part of the operating pipeline. The results of finite-element modeling, identification of pipe natural modes and its modification under the influence of virtual failure are discussed. The work considers the results of experimental research of dynamic behavior of the operating pipe models using one of OMA techniques and comparing dynamic properties with the modeled data. The study results demonstrate sensitivity of modal shape parameters to modification of operating pipeline technical state. Two strategies of pipeline repair – with continuously condition-based monitoring with proposed technology and without such monitoring, was discussed. Markov chain reliability models for each strategy were analyzed and reliability improvement factor for proposed technology of monitoring in compare with traditional one was evaluated. It is resumed about ability of operating pipeline condition monitoring by measuring dynamic deformations of the operating pipe and OMA techniques application for dynamic properties extraction.

  17. Amenities and Rural Appalachia Economic Growth

    OpenAIRE

    Deller, Steven C.; Lledo, Victor

    2007-01-01

    Patterns of economic growth in rural Appalachia are examined with a focus on natural and built amenities. While the literature is clear that rural areas endowed with scenic beauty, lakes, forests, and wildlife, among other natural amenities, and coupled with built amenities such as golf courses, are experiencing robust economic growth. It is not clear if these patterns extend to rural Appalachia. In this applied research study we use data for rural U.S. counties. We estimate an augmented Carl...

  18. Entanglement Mapping VS. Quantum Conditional Probability Operator

    Science.gov (United States)

    Chruściński, Dariusz; Kossakowski, Andrzej; Matsuoka, Takashi; Ohya, Masanori

    2011-01-01

    The relation between two methods which construct the density operator on composite system is shown. One of them is called an entanglement mapping and another one is called a quantum conditional probability operator. On the base of this relation we discuss the quantum correlation by means of some types of quantum entropy.

  19. Pointwise ergodic theorems beyond amenable groups

    CERN Document Server

    Bowen, Lewis

    2011-01-01

    We prove pointwise and maximal ergodic theorems for probability measure preserving actions of any countable group, provided it admits an essentially free, weakly mixing amenable action of stable type III_r for some r >0. Our approach is based on the following two principles. First, it is possible to generalize the ergodic theory of measure-preserving actions of amenable groups to include probability-measure-preserving amenable equivalence relations. Second, it is possible to reduce the proof of ergodic theorems for actions of a general group to the proof of ergodic theorems in an associated measure-preserving amenable equivalence relation, provided the group admits an amenable action with the properties stated above. The general ergodic theorems established here are used in a sequel paper to prove mean and pointwise ergodic theorems for arbitrary Gromov-hyperbolic groups.

  20. Operant conditioning of autobiographical memory retrieval.

    Science.gov (United States)

    Debeer, Elise; Raes, Filip; Williams, J Mark G; Craeynest, Miet; Hermans, Dirk

    2014-01-01

    Functional avoidance is considered as one of the key mechanisms underlying overgeneral autobiographical memory (OGM). According to this view OGM is regarded as a learned cognitive avoidance strategy, based on principles of operant conditioning; i.e., individuals learn to avoid the emotionally painful consequences associated with the retrieval of specific negative memories. The aim of the present study was to test one of the basic assumptions of the functional avoidance account, namely that autobiographical memory retrieval can be brought under operant control. Here 41 students were instructed to retrieve personal memories in response to 60 emotional cue words. Depending on the condition, they were punished with an aversive sound for the retrieval of specific or nonspecific memories in an operant conditioning procedure. Analyzes showed that the course of memory specificity significantly differed between conditions. After the procedure participants punished for nonspecific memories retrieved significantly more specific memories compared to participants punished for specific memories. However, whereas memory specificity significantly increased in participants punished for specific memories, it did not significantly decrease in participants punished for nonspecific memories. Thus, while our findings indicate that autobiographical memory retrieval can be brought under operant control, they do not support a functional avoidance view on OGM.

  1. Effect of operating conditions on gearbox noise

    Science.gov (United States)

    Oswald, Fred B.; Zakrajsek, James J.; Townsend, Dennis P.; Atherton, William; Lin, Hsiang Hsi

    1992-04-01

    Low contact ratio spur gears were tested in the NASA gear noise rig to study the noise radiated from the top of the gearbox. The measured sound power from the gearbox top was obtained from a near field acoustic intensity scan taken at 63 nodes just above the surface. The sound power was measured at a matrix of 45 operating speeds and torque levels. Results are presented in the form of a spectral speed map and as a plot of sound power versus torque (at constant speed) and as sound power versus speed (at constant torque). Because of the presence of vibration modes, operating speed was found to have more impact on noise generation than torque level. A NASA gear dynamics code was used to compute the gear tooth dynamic overload at the same 45 operating conditions used for the experiment. Similar trends were found between the analytical results for dynamic tooth overload and experimental results for sound power. Dynamic analysis may be used to design high quality gears with profile relief optimized for minimum dynamic load and noise.

  2. The operational meaning of quantum conditional information

    CERN Document Server

    Devetak, I; Devetak, Igor; Yard, Jon

    2006-01-01

    With a statistical view towards information and noise, information theory derives ultimate limitations on information processing tasks. These limits are generally expressed in terms of entropic measures of information and correlations. Here we answer the quantum information-theoretic question: ``How correlated are two quantum systems from the perspective of a third?" by solving the following `quantum state redistribution' problem. Given an arbitrary quantum state of three systems, where Alice holds two and Bob holds one, what is the cost, in terms of quantum communication and entanglement, for Alice to give one of her parts to Bob? The communication cost gives the first operational interpretation to quantum conditional mutual information. The optimal procedure is self-dual under time reversal and is perfectly composable. This generalizes known protocols such as the state merging and fully quantum Slepian-Wolf protocols, from which almost every known protocol in quantum Shannon theory can be derived.

  3. MSTAR extended operating conditions: a tutorial

    Science.gov (United States)

    Keydel, Eric R.; Lee, Shung W.; Moore, John T.

    1996-06-01

    One key advantage of the model-based approach for automatic target recognition (ATR) is the wide range of targets and acquisition scenarios that can be accommodated without algorithm re-training. This accrues from the use of predictive models which can be adjusted to hypothesized scenarios on-line. Approaches which rely on measured signature exemplars as the source of reference data for signature matching are constrained to those scenarios represented in the reference data base. The moving and stationary target recognition (MSTAR) program will advance the state-of-the-art in model-based ATR by developing, evaluating, and testing algorithm performance against a set of extended operating conditions (EOCs) designed to reflect real-world battlefield scenarios. In addition to full 360 deg target aspect coverage over a range of depression angles, the EOCs include variations in squint angle, target articulation and configurations, obscuration due to occlusion and/or layover, and intra-class target variability. These conditions can have a profound impact on the nature of the target signature, necessitating the development of explicit prediction and reasoning algorithms to provide robust target recognition. This paper provides a tutorial description of the impact of the MSTAR EOCs on SAR target signatures. A brief background discussion of the SAR imaging process is presented first. This is followed by a description of the impact of each EOC category on the target signature along with synthetic imagery examples to illustrate this impact.

  4. LHCb Conditions database operation assistance systems

    Science.gov (United States)

    Clemencic, M.; Shapoval, I.; Cattaneo, M.; Degaudenzi, H.; Santinelli, R.

    2012-12-01

    The Conditions Database (CondDB) of the LHCb experiment provides versioned, time dependent geometry and conditions data for all LHCb data processing applications (simulation, high level trigger (HLT), reconstruction, analysis) in a heterogeneous computing environment ranging from user laptops to the HLT farm and the Grid. These different use cases impose front-end support for multiple database technologies (Oracle and SQLite are used). Sophisticated distribution tools are required to ensure timely and robust delivery of updates to all environments. The content of the database has to be managed to ensure that updates are internally consistent and externally compatible with multiple versions of the physics application software. In this paper we describe three systems that we have developed to address these issues. The first system is a CondDB state tracking extension to the Oracle 3D Streams replication technology, to trap cases when the CondDB replication was corrupted. Second, an automated distribution system for the SQLite-based CondDB, providing also smart backup and checkout mechanisms for the CondDB managers and LHCb users respectively. And, finally, a system to verify and monitor the internal (CondDB self-consistency) and external (LHCb physics software vs. CondDB) compatibility. The former two systems are used in production in the LHCb experiment and have achieved the desired goal of higher flexibility and robustness for the management and operation of the CondDB. The latter one has been fully designed and is passing currently to the implementation stage.

  5. Perception towards Public Amenities in Malaysia

    Directory of Open Access Journals (Sweden)

    Rozmi Ismail

    2013-10-01

    Full Text Available The environment where a person lives has a significant impact on his or her development. The objective of the study is to determine the person's perception and satisfaction towards safety and public amenity nearby. Purposive sampling method was utilized to collect data in Selangor and Kelang Vally, Malaysia. Data were collected through interview using a set of questionnaire and analyzed using the SPSS program. The results of the study showed that in terms of public amenities and physical surroundings, the most persons used own car to attend personal and family matters such as clinic and programme. On the other hand, the most safety elements which persons employed to protect their house and family were installing door and window grilles, lights on and informing neighbor when going out for the whole night or longer.

  6. Ideal Amenability of Banach Algebras on Locally Compact Groups

    Indian Academy of Sciences (India)

    M Eshaghi Gordji; S A R Hosseiniun

    2005-08-01

    In this paper we study the ideal amenability of Banach algebras. Let $\\mathcal{A}$ be a Banach algebra and let be a closed two-sided ideal in $\\mathcal{A}, \\mathcal{A}$ is -weakly amenable if $H^1(\\mathcal{A},I^∗)=\\{0\\}$. Further, $\\mathcal{A}$ is ideally amenable if $\\mathcal{A}$ is -weakly amenable for every closed two-sided ideal in $\\mathcal{A}$. We know that a continuous homomorphic image of an amenable Banach algebra is again amenable. We show that for ideal amenability the homomorphism property for suitable direct summands is true similar to weak amenability and we apply this result for ideal amenability of Banach algebras on locally compact groups.

  7. Control of Propeller Cavitation in Operational Conditions

    NARCIS (Netherlands)

    Vrijdag, A.

    2009-01-01

    Off design conditions can have a severe impact on ship propulsion system behaviour. Resistance increase for instance leads to a higher engine loading, and can also easily lead to a decrease of cavitation inception speed with respect to calm water conditions. Wakefield variations due to ship motions,

  8. Internações pediátricas por condições sensíveis à atenção primária em Montes Claros, Minas Gerais, Brasil Admissions to pediatric hospital for conditions amenable to primary care in Montes Claros, Minas Gerais, Brazil

    Directory of Open Access Journals (Sweden)

    Antônio Prates Caldeira

    2011-03-01

    Full Text Available OBJETIVOS: avaliar a prevalência e os fatores associados às internações pediátricas por condições sensíveis à atenção primária (CSAP. MÉTODOS: realizouse inquérito hospitalar ao longo de um ano, com amostra representativa ealeatória de crianças internadas em um município do norte de Minas Gerais. Enfermarias pediátricas foram visitadas uma vez por semana em dias diferentes. Foram investigadas variáveis demográficas, socioeconômicas e relacionadas às condições de saúde. Para a definição das afecções sensíveis a atenção primária utilizou-se a relação oficial publicada pelo Ministério da Saúde. A regressão de Poisson foi utilizada para avaliação conjunta das variáveis associadas às internações por CSAP. RESULTADOS: foram entrevistadas 365 famílias e a prevalência de internações por CSAP foi de 41,4%(n=151. O modelo final revelou que, em uma análise conjunta, as variáveis se mantiveram estatisticamente associadas com as internações por CSAP foram: residir em área da Estratégia de Saúde da Família (RP=1,19; IC95%=1,03-1,61 e idade menor que dois anos de idade (RP=1,42; IC95%=1,35-1,51. CONCLUSÕES: a prevalência observada é semelhante à encontrada em outros estudos e salienta a necessidade de melhoria dos cuidados ambulatoriais para a faixa etária estudada.OBJECTIVE: to evaluate the prevalence and factors associated with admission to pediatric hospital for conditions amenable to primary care. METHODS: an investigation was carried out for the duration of one year, with a representative sample of children admitted to hospital in a municipality in thenorth of the Brazilian State of Minas Gerais. Pediatric wards were visited once a week on different days. Demographic, socio-economic and health variables were studied. Conditions amenable to primary care were established using the official report published by the Brazilian Ministry of Health. The Poisson regression was used to evaluate the set of

  9. Module Amenability and Tensor Product of Semigroup Algebras

    OpenAIRE

    A. Bodaghi

    2016-01-01

    Let S be an inverse semigroup with an upward directed set of idempotents E. In this paper we prove that if S is amenable, then ` 1 (S) Nc` 1 (S) is module amenable as an ` 1 (E)-module. Also we show that ` 1 (S) Nc` 1 (S) is module super-amenable if an appropriate group homomorphic image of S is finite

  10. Extreme amenability of abelian $L_0$ groups

    CERN Document Server

    Sabok, Marcin

    2012-01-01

    We show that for any abelian topological group $G$ and arbitrary diffused submeasure $\\mu$, every continuous action of $L_0(\\mu,G)$ on a compact space has a fixed point. This generalizes earlier results of Herer and Christensen, Glasner, Furstenberg and Weiss, and Farah and Solecki. This also answers a question posed by Farah and Solecki. In particular, it implies that if $H$ is of the form $L_0(\\mu,\\mathbb{R})$, then $H$ is extremely amenable if and only if $H$ has no nontrivial characters, which gives an evidence for an affirmative answer to a question of Pestov. The proof is based on estimates of chromatic numbers of certain graphs on $\\mathbb{Z}^n$. It uses tools from algebraic topology and builds on the work of Farah and Solecki.

  11. Models of household location and urban amenities

    DEFF Research Database (Denmark)

    van Duijn, Mark; Möhlmann, Jan; Mulalic, Ismir

    1.1 Skilled workers and regional development The research carried out in the HELP project concerns the importance of urban amenities for the location choices of highly educated workers. Why is this important? A general answer to this question is that such workers are generally regarded as being...... the drivers of economic prosperity and growth in cities. In this introductory section we discuss some evidence that motivates this idea. In ‘The Economy of Cities’ Jane Jacobs (1970) puts forward the thesis that human interaction is a crucial aspect of urban economies. Economists such as Lucas (1988) picked...... as a kind of agglomeration economies. Cities thus become more productive places and this process works continuously and generates growth. Empirical evidence in favor of this hypothesis was provided by Rauch (1993) who estimated that an additional year of schooling of the labor force in an urban area gave...

  12. LHCb Conditions Database Operation Assistance Systems

    CERN Multimedia

    Shapoval, Illya

    2012-01-01

    The Conditions Database of the LHCb experiment (CondDB) provides versioned, time dependent geometry and conditions data for all LHCb data processing applications (simulation, high level trigger, reconstruction, analysis) in a heterogeneous computing environment ranging from user laptops to the HLT farm and the Grid. These different use cases impose front-end support for multiple database technologies (Oracle and SQLite are used). Sophisticated distribution tools are required to ensure timely and robust delivery of updates to all environments. The content of the database has to be managed to ensure that updates are internally consistent and externally compatible with multiple versions of the physics application software. In this paper we describe three systems that we have developed to address these issues: - an extension to the automatic content validation done by the “Oracle Streams” replication technology, to trap cases when the replication was unsuccessful; - an automated distribution process for the S...

  13. Poor weather conditions and flight operations: Implications for air ...

    African Journals Online (AJOL)

    Poor weather conditions and flight operations: Implications for air transport hazard ... Ethiopian Journal of Environmental Studies and Management ... fog, dust haze and line squall that affect flight operation such as flight delays, diversion and ...

  14. Operational conditions for random-number generation

    Science.gov (United States)

    Compagner, A.

    1995-11-01

    Ensemble theory is used to describe arbitrary sequences of integers, whether formed by the decimals of π or produced by a roulette or by any other means. Correlation coefficients of any range and order are defined as Fourier transforms of the ensemble weights. Competing definitions of random sequences are considered. Special attention is given to sequences of random numbers needed for Monte Carlo calculations. Different recipes for those sequences lead to correlations that vary in range and order, but the total amount of correlation is the same for all sequences of a given length (without internal periodicities). For maximum-length sequences produced by linear algorithms, most correlation coefficients are zero, but the remaining ones are of absolute value 1. In well-tempered sequences, these complete correlations are of high order or of very long range. General conditions to be obeyed by random-number generators are discussed and a qualitative method for comparing different recipes is given.

  15. 49 CFR 325.35 - Ambient conditions; highway operations.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Ambient conditions; highway operations. 325.35... Ambient conditions; highway operations. (a)(1) Sound. The ambient A-weighted sound level at the microphone... § 325.23. (2) The measured ambient level must be 10 dB(A) or more below that level specified in §...

  16. Transformer real-time reliability model based on operating conditions

    Institute of Scientific and Technical Information of China (English)

    HE Jian; CHENG Lin; SUN Yuan-zhang

    2007-01-01

    Operational reliability evaluation theory reflects real-time reliability level of power system. The component failure rate varies with operating conditions. The impact of real-time operating conditions such as ambient temperature and transformer MVA (megavolt-ampere) loading on transformer insulation life is studied in this paper. The formula of transformer failure rate based on the winding hottest-spot temperature (HST) is given. Thus the real-time reliability model of transformer based on operating conditions is presented. The work is illustrated using the 1979 IEEE Reliability Test System. The changes of operating conditions are simulated by using hourly load curve and temperature curve, so the curves of real-time reliability indices are obtained by using operational reliability evaluation.

  17. Various notions of amenability for not necessarily locally compact groupoids

    Directory of Open Access Journals (Sweden)

    Mădălina Roxana Buneci

    2014-08-01

    Full Text Available We start with a groupoid G endowed with a family W of subsets mimicking the properties of a neighborhood basis of the unit space (of a topological groupoid with paracompact unit space. Using the family W we endow each G-space with a uniform structure. The uniformities of the G-spaces allow us to define various notions of amenability for the G-equivariant maps. As in [C. Anantharaman-Delaroche and J. Renault, Amenable Groupoids. Monographie de L'Enseignement Mathematique No 36, Geneve, 2000], the amenability of the groupoid G is defined as the amenability of its range map. If the groupoid G is a group, all notions of amenability that we introduce coincide with the classical notion of amenability for topological (not necessarily locally-compact groups.

  18. Ternary Weakly Amenable C*-algebras and JB*-triples

    CERN Document Server

    Ho, Tony; Russo, Bernard

    2012-01-01

    A well known result of Haagerup from 1983 states that every C*-algebra A is weakly amenable, that is, every (associative) derivation from A into its dual is inner. A Banach algebra B is said to be ternary weakly amenable if every continuous Jordan triple derivation from B into its dual is inner. We show that commutative C*-algebras are ternary weakly amenable, but that B(H) and K(H) are not, unless H is finite dimensional. More generally, we inaugurate the study of weak amenability for Jordan Banach triples, focussing on commutative JB*-triples and some Cartan factors.

  19. A Banach space-valued ergodic theorem for amenable groups and applications

    CERN Document Server

    Pogorzelski, Felix

    2012-01-01

    In this paper we study unimodular amenable groups. The first part is devoted to results on the existence of uniform families of quasi tilings for these groups. In light of that, constructions of Ornstein and Weiss are extended by quantitative estimates for the covering properties of the corresponding decompositions. Afterwards, we apply the developed methods to obtain an abstract ergodic theorem for a class of functions mapping subsets of the group into some Banach space. Moreover, applications of this convergence result are studied: the uniform existence of the integrated density of states (IDS) for operators on amenable Cayley graphs; the uniform existence of the IDS for operators on discrete structures being quasi-isometric to some amenable group; the approximation of L2-Betti numbers on cellular CW-complexes; the existence of certain densities of clusters in a percolated Cayley graph.

  20. approach to gearbox diagnosis under variable operating conditions

    Directory of Open Access Journals (Sweden)

    Lixiang Duan

    2016-08-01

    Full Text Available Gearbox diagnosis under stationary operating conditions has been extensively investigated; however, variable operating conditions such as load and speed changes play important roles in affecting the accuracy of gearbox diagnosis. This article presents an integrative approach of intrinsic time-scale decomposition and hierarchical temporal memory for gearbox diagnosis under variable operating conditions. A total of two modules are emphasized including a feature extraction method and an integrative feature fusion and classification model. Intrinsic time-scale decomposition method is investigated to extract the gearbox features which are insensitive to variable operating conditions, and its performance overcomes the commonly used empirical mode decomposition in terms of decomposition result and computational efficiency. Hierarchical temporal memory integrates feature fusion and pattern classification in one model to autonomously diagnose gearbox defect. Performance comparison among the presented method, back-propagation neural network, support vector machine, and fuzzy c-means clustering using experimental data demonstrate the effectiveness of the presented method.

  1. 14 CFR 135.227 - Icing conditions: Operating limitations.

    Science.gov (United States)

    2010-01-01

    ... OPERATING REQUIREMENTS: COMMUTER AND ON DEMAND OPERATIONS AND RULES GOVERNING PERSONS ON BOARD SUCH AIRCRAFT... aircraft that has frost, ice, or snow adhering to any rotor blade, propeller, windshield, wing, stabilizing... may take off an airplane any time conditions are such that frost, ice, or snow may reasonably...

  2. Pain Report and Pain-Related Evoked Potentials Operantly Conditioned

    NARCIS (Netherlands)

    Lousberg, Richel; Vuurman, Eric; Lamers, Theo; Breukelen, van Gerard; Jongen, Ellen; Rijnen, Heidi; Maessen, Christa; Hermens, Hermie

    2005-01-01

    Objective: The purpose of the present study was to answer the ques- tion whether pain report can be increased and decreased by operant conditioning. We predicted that the conditioned pain effects would remain significant after correction for social desirability and fantasy proneness. Furthermore, we

  3. Pain Report and Pain-Related Evoked Potentials Operantly Conditioned

    NARCIS (Netherlands)

    Lousberg, Richel; Vuurman, Eric; Lamers, Theo; van Breukelen, Gerard; Jongen, Ellen; Rijnen, Heidi; Maessen, Christa; Hermens, Hermanus J.

    Objective: The purpose of the present study was to answer the ques- tion whether pain report can be increased and decreased by operant conditioning. We predicted that the conditioned pain effects would remain significant after correction for social desirability and fantasy proneness. Furthermore, we

  4. Design and Implementation of Air Conditioning System in Operating Room

    Directory of Open Access Journals (Sweden)

    Htet Htet Aung

    2014-10-01

    Full Text Available The system is air conditioning system in operating room. The main objective of the system was implemented to provide air balance and temperature necessary conditions and to control airflow system for ventilation units in operating room. The operation room can be controlled with fuzzy expert system and describes the desired outputs. Input parameters such as temperature, humidity, oxygen and particle are used and output parameters are chosen as air conditioning motor speed and exhaust motor speed. Input parameters of the system are taken into account optimal conditions based on oxygen as medium and other parameters are chosen minimum condition for operating room. The airflow control system is determined the two components: the airflow block and the thermal block for ventilation units in operating room. The mathematical modeling of each such system based on a computational procedure and to combine them together in an efficient manner. Whether it supports to the most suitable control for the system prototype was determined by simulating the operation with varying the number of personnel and duration of time. Finally, according to the combination of temperature and airflow regulations with PI controller, the results of simulation of the entire ventilation unit control system is obtained.

  5. Structural Health Monitoring in Changing Operational Conditions Using Tranmissibility Measurements

    Directory of Open Access Journals (Sweden)

    Christof Devriendt

    2010-01-01

    Full Text Available This article uses frequency domain transmissibility functions for detecting and locating damage in operational conditions. In recent articles numerical and experimental examples were presented and the possibility to use the transmissibility concept for damage detection seemed quite promising. In the work discussed so far, it was assumed that the operational conditions were constant, the structure was excited by a single input in a fixed location. Transmissibility functions, defined as a simple ratio between two measured responses, do depend on the amplitudes or locations of the operational forces. The current techniques fail in the case of changing operational conditions. A suitable operational damage detection method should however be able to detect damage in a very early stage even in the case of changing operational conditions. It will be demonstrated in this paper that, by using only a small frequency band around the resonance frequencies of the structure, the existing methods can still be used in a more robust way. The idea is based on the specific property that the transmissibility functions become independent of the loading condition in the system poles. A numerical and experimental validation will be given.

  6. Validation of Walk Score for estimating access to walkable amenities.

    Science.gov (United States)

    Carr, Lucas J; Dunsiger, Shira I; Marcus, Bess H

    2011-11-01

    Proximity to walkable destinations or amenities is thought to influence physical activity behaviour. Previous efforts attempting to calculate neighbourhood walkability have relied on self-report or time-intensive and costly measures. Walk Score is a novel and publicly available website that estimates neighbourhood walkability based on proximity to 13 amenity categories (eg, grocery stores, coffee shops, restaurants, bars, movie theatres, schools, parks, libraries, book stores, fitness centres, drug stores, hardware stores, clothing/music stores). The purpose of this study is to test the validity and reliability of Walk Score for estimating access to objectively measured walkable amenities. Walk Scores of 379 residential/non-residential addresses in Rhode Island were manually calculated. Geographic information systems (GIS) was used to objectively measure 4194 walkable amenities in the 13 Walk Score categories. GIS data were aggregated from publicly available data sources. Sums of amenities within each category were matched to address data, and Pearson correlations were calculated between the category sums and address Walk Scores. Significant correlations were identified between Walk Score and all categories of aggregated walkable destinations within a 1-mile buffer of the 379 residential and non-residential addresses. Test-retest reliability correlation coefficients for a subsample of 100 addresses were 1.0. These results support Walk Score as a reliable and valid measure of estimating access to walkable amenities. Walk Score may be a convenient and inexpensive option for researchers interested in exploring the relationship between access to walkable amenities and health behaviours such as physical activity.

  7. Multinorms and Approximate Amenability of Weighted Group Algebras

    Directory of Open Access Journals (Sweden)

    Saman Ghaderkhani

    2014-01-01

    Full Text Available Let G be a locally compact group, and take p,q with 1≤p,q<∞. We prove that, for any left (p,q-multiinvariant functional on L∞(G and for any weight function ω≥1 on G, the approximate amenability of the Banach algebra L1(G,ω implies the left (p,q-amenability of G, but in general the opposite is not true. Our proof uses the notion of multinorms. We also investigate the approximate amenability of M(G,ω.

  8. Selection of efficient operating modes of combines depending on operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Alshits, Ya.I.; Konovalov, V.I.; Osokin, P.A.

    1983-01-01

    A technique is presented for selecting the efficient operating modes, determining the permissible velocities for movement and productivity of combines and complexes depending on their operating conditions and types of electric motors used. Parameters are presented for efficient operating modes of the coal-recovery combine 2 K52M under different conditions when it is completed by high-momentum electric motor of the type EDK04-5U5 or the motor EDK04-4MU5. Results are presented of experimental operation in the mines of the combines 2K52 with high-momentum electric motors.

  9. System and method of vehicle operating condition management

    Science.gov (United States)

    Sujan, Vivek A.; Vajapeyazula, Phani; Follen, Kenneth; Wu, An; Moffett, Barty L.

    2015-10-20

    A vehicle operating condition profile can be determined over a given route while also considering imposed constraints such as deviation from time targets, deviation from maximum governed speed limits, etc. Given current vehicle speed, engine state and transmission state, the present disclosure optimally manages the engine map and transmission to provide a recommended vehicle operating condition that optimizes fuel consumption in transitioning from one vehicle state to a target state. Exemplary embodiments provide for offline and online optimizations relative to fuel consumption. The benefit is increased freight efficiency in transporting cargo from source to destination by minimizing fuel consumption and maintaining drivability.

  10. Sex differences in learning processes of classical and operant conditioning.

    Science.gov (United States)

    Dalla, Christina; Shors, Tracey J

    2009-05-25

    Males and females learn and remember differently at different times in their lives. These differences occur in most species, from invertebrates to humans. We review here sex differences as they occur in laboratory rodent species. We focus on classical and operant conditioning paradigms, including classical eyeblink conditioning, fear-conditioning, active avoidance and conditioned taste aversion. Sex differences have been reported during acquisition, retention and extinction in most of these paradigms. In general, females perform better than males in the classical eyeblink conditioning, in fear-potentiated startle and in most operant conditioning tasks, such as the active avoidance test. However, in the classical fear-conditioning paradigm, in certain lever-pressing paradigms and in the conditioned taste aversion, males outperform females or are more resistant to extinction. Most sex differences in conditioning are dependent on organizational effects of gonadal hormones during early development of the brain, in addition to modulation by activational effects during puberty and adulthood. Critically, sex differences in performance account for some of the reported effects on learning and these are discussed throughout the review. Because so many mental disorders are more prevalent in one sex than the other, it is important to consider sex differences in learning when applying animal models of learning for these disorders. Finally, we discuss how sex differences in learning continue to alter the brain throughout the lifespan. Thus, sex differences in learning are not only mediated by sex differences in the brain, but also contribute to them.

  11. Conditional stability versus ill-posedness for operator equations with monotone operators in Hilbert space

    Science.gov (United States)

    Ioan Boţ, Radu; Hofmann, Bernd

    2016-12-01

    In the literature on singular perturbation (Lavrentiev regularization) for the stable approximate solution of operator equations with monotone operators in the Hilbert space the phenomena of conditional stability and local well-posedness or ill-posedness are rarely investigated. Our goal is to present some studies which try to bridge this gap. So we present new results on the impact of conditional stability on error estimates and convergence rates for the Lavrentiev regularization and distinguish for linear problems well-posedness and ill-posedness in a specific manner motivated by a saturation result. Taking into account that the behavior of the bias (regularization error in the noise-free case) is crucial, general convergence rates, including logarithmic rates, are derived for linear operator equations by means of the method of approximate source conditions. This allows us to extend well-known convergence rate results for the Lavrentiev regularization that were based on general source conditions to the case of non-selfadjoint linear monotone forward operators for which general source conditions fail. Examples presenting the self-adjoint multiplication operator as well as the non-selfadjoint fractional integral operator and Cesàro operator illustrate the theoretical results. Extensions to the nonlinear case under specific conditions on the nonlinearity structure complete the paper.

  12. VERIFICATION OF GEAR DYNAMIC MODEL IN DIFFERENT OPERATING CONDITIONS

    Directory of Open Access Journals (Sweden)

    Grzegorz PERUŃ

    2014-09-01

    Full Text Available The article presents the results of verification of the drive system dynamic model with gear. Tests were carried out on the real object in different operating conditions. For the same assumed conditions were also carried out simulation studies. Comparison of the results obtained from those two series of tests helped determine the suitability of the model and verify the possibility of replacing experimental research by simulations with use of dynamic model.

  13. (2-1)-Ideal amenability of triangular banach algebras

    Indian Academy of Sciences (India)

    S Etemad; M Ettefagh

    2015-05-01

    Let $\\mathcal{A}$ and $\\mathcal{B}$ be two unital Banach algebras and let $\\mathcal{M}$ be an unital Banach $\\mathcal{A}$, $\\mathcal{B}$-module. Also, let $\\mathcal{T}=\\left[\\begin{smallmatrix} \\mathcal{A} & \\mathcal{M}\\\\ & \\mathcal{B}\\end{smallmatrix}\\right]$ be the corresponding triangular Banach algebra. Forrest and Marcoux (Trans. Amer. Math. Soc. 354 (2002) 1435–1452) have studied the -weak amenability of triangular Banach algebras. In this paper, we investigate (2-1)-ideal amenability of $\\mathcal{T}$ for all ≥ 1. We introduce the structure of ideals of these Banach algebras and then, we show that (2-1)-ideal amenability of $\\mathcal{T}$ depends on (2-1)-ideal amenability of Banach algebras $\\mathcal{A}$ and $\\mathcal{B}$.

  14. A groupoid approach to L\\"uck's amenability conjecture

    CERN Document Server

    Kyed, David

    2012-01-01

    We prove that amenability of a discrete group is equivalent to dimension flatness of certain ring inclusions naturally associated with measure preserving actions of the group. This provides a group-measure space theoretic solution to a conjecture of L\\"uck stating that amenability of a group is characterized by dimension flatness of the inclusion of its complex group algebra into the associated von Neumann algebra.

  15. Amenability and Contractibility Modulo an Ideal of Banach Algebras

    Directory of Open Access Journals (Sweden)

    Hamidreza Rahimi

    2014-01-01

    Full Text Available We investigate the concept of amenability modulo an ideal of Banach algebra, showing that amenability modulo an ideal can be characterized by the existence of virtual and approximate diagonal modulo an ideal. We also study the concept of contractible modulo an ideal of Banach algebra. As a consequence, we prove a version of Selivanov's theorem for a large class of semigroups, including E-inversive E-semigroup and eventually inverse semigroups.

  16. Risk management of exposure to chemicals under operational conditions

    NARCIS (Netherlands)

    Langenberg, J.P.

    2007-01-01

    The HFM panel has decided to install an Exploratory Team, ET-078, which should advise whether or not a Technical Group (TG) should be established on the subject of risk management of exposure to chemicals under operational conditions. This paper described the context and approach of ET-078.

  17. A Problem-Solving Approach to Teaching Operant Conditioning

    Science.gov (United States)

    Shields, Carolyn; Gredler, Margaret

    2003-01-01

    Psychology students frequently have misconceptions of basic concepts in operant conditioning. Prior classroom observations revealed that most students defined positive reinforcement as reward and equated negative reinforcement and punishment. Students also labeled positive reinforcement as rewarding good behavior and negative reinforcement as…

  18. Spontaneous decisions and operant conditioning in fruit flies.

    Science.gov (United States)

    Brembs, Björn

    2011-05-01

    Already in the 1930s Skinner, Konorski and colleagues debated the commonalities, differences and interactions among the processes underlying what was then known as "conditioned reflexes type I and II", but which is today more well-known as classical (Pavlovian) and operant (instrumental) conditioning. Subsequent decades of research have confirmed that the interactions between the various learning systems engaged during operant conditioning are complex and difficult to disentangle. Today, modern neurobiological tools allow us to dissect the biological processes underlying operant conditioning and study their interactions. These processes include initiating spontaneous behavioral variability, world-learning and self-learning. The data suggest that behavioral variability is generated actively by the brain, rather than as a by-product of a complex, noisy input-output system. The function of this variability, in part, is to detect how the environment responds to such actions. World-learning denotes the biological process by which value is assigned to environmental stimuli. Self-learning is the biological process which assigns value to a specific action or movement. In an operant learning situation using visual stimuli for flies, world-learning inhibits self-learning via a prominent neuropil region, the mushroom-bodies. Only extended training can overcome this inhibition and lead to habit formation by engaging the self-learning mechanism. Self-learning transforms spontaneous, flexible actions into stereotyped, habitual responses.

  19. A minicomputer interface for realtime operations: an application to operant conditioning.

    Science.gov (United States)

    Mayor, S J; Wilson, J

    1975-09-01

    A PDP-12 interface was designed, constructed, and tested for realtime imput and output of binary information. Within limits this interface can be used with any peripheral device which operates in the binary mode. In addition to its generality of application the interface features include ease of expansion and low cost. A description of its design and operation is give here is terms of a typical application: the control of behavioral equipment (i.e. "Skinner Boxes") for operant conditioning.

  20. Mathematical modelling of unglazed solar collectors under extreme operating conditions

    DEFF Research Database (Denmark)

    Bunea, M.; Perers, Bengt; Eicher, S.

    2015-01-01

    average temperature levels at the evaporator. Simulation of these systems requires a collector model that can take into account operation at very low temperatures (below freezing) and under various weather conditions, particularly operation without solar irradiation.A solar collector mathematical model......Combined heat pumps and solar collectors got a renewed interest on the heating system market worldwide. Connected to the heat pump evaporator, unglazed solar collectors can considerably increase their efficiency, but they also raise the coefficient of performance of the heat pump with higher...... was found due to the condensation phenomenon and up to 40% due to frost under no solar irradiation. This work also points out the influence of the operating conditions on the collector's characteristics.Based on experiments carried out at a test facility, every heat flux on the absorber was separately...

  1. Solid oxide fuel cell performance under severe operating conditions

    DEFF Research Database (Denmark)

    Koch, Søren; Hendriksen, P.V.; Mogensen, Mogens Bjerg

    2006-01-01

    The performance and degradation of Solid Oxide Fuel Cells (SOFC) were studied under severe operating conditions. The cells studied were manufactured in a small series by ECN, in the framework of the EU funded CORE-SOFC project. The cells were of the anode-supported type with a double layer LSM...... cathode. They were operated at 750 °C or 850 °C in hydrogen with 5% or 50% water at current densities ranging from 0.25 A cm–2 to 1 A cm–2 for periods of 300 hours or more. The area specific cell resistance, corrected for fuel utilisation, ranged between 0.20 Ω cm2 and 0.34 Ω cm2 at 850 °C and 520 m......V, and between 0.51 Ω cm2 and 0.92 Ω cm2 at 750 °C and 520 mV. The degradation of cell performance was found to be low (ranging from 0 to 8%/1,000 hours) at regular operating conditions. Voltage degradation rates of 20 to 40%/1,000 hours were observed under severe operating conditions, depending on the test...

  2. Influences of operating conditions on continuous lactulose synthesis in an enzymatic membrane reactor system: A basis prior to long-term operation.

    Science.gov (United States)

    Sitanggang, Azis Boing; Drews, Anja; Kraume, Matthias

    2015-06-10

    Lactulose synthesis was performed in a continuous stirred enzymatic membrane reactor. Each investigated operating condition (agitation, pH, feed molar ratio of lactose to fructose (mL/mF ratio), hydraulic residence time (HRT)) had an influence on reaction performances, in terms of lactulose concentration, productivity and selectivity. Lactulose concentration was maximum at an mL/mF ratio of 1/2. Higher than this ratio, synthesis of galactooligosaccharides was promoted rather than lactulose. At mL/mF ratios lower than 1/2, enzyme inhibition was pronounced to the detriment of lactulose production. At 7 or 9h HRT, higher lactulose concentrations were obtained than at shorter HRTs. Applying an mL/mF ratio of 1/2 and an HRT of 9h in a long-term operation, nearly constant lactulose concentration was reached after 23h and lasted up to 32h with a mean concentration of 14.51±0.07g/L and a reaction selectivity of 0.075-0.080mollactulose/molcons.lactose. After 7d, lactulose concentration reduced by 31%. A continuous synthesis of lactulose at lab-scale was shown to be amenable using a membrane reactor process. Moreover, for process evaluation, this study can bridge the gap between batch laboratory scale and continuous full-scale operation regarding lactulose synthesis. Copyright © 2015 Elsevier B.V. All rights reserved.

  3. Optimisation of Shift Reactor Operating Conditions to Maximise Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez, J. M.; Marano, M.; Ruiz, E.

    2011-07-28

    This report compiles the results of the work conducted by CIEMAT for Task 6.5 Shift reaction of the FLEXGAS project Near Zero Emission Advanced Fluidized Bed Gasification, which has been carried out with financial support from the Research Fund for Coal and Steel, RFCR-CT-2007-00005. The activity of an iron-chromium-based catalyst for the water gas shift reaction is studied. Results about WGS experiments conducted by CIEMAT on laboratory scale under different operating conditions are presented. The influence on the activity of the catalyst of main operating parameters- temperature, pressure, excess steam, and space velocity and gas composition - is evaluated and discussed. (Author) 19 refs.

  4. Marine Vessel Models in Changing Operational Conditions - A Tutorial

    DEFF Research Database (Denmark)

    Perez, Tristan; Sørensen, Asgeir; Blanke, Mogens

    2006-01-01

    conditions (VOC). However, since marine systems operate in changing VOCs, there is a need to adapt the models. To date, there is no theory available to describe a general model valid across different VOCs due to the complexity of the hydrodynamic involved. It is believed that system identification could......This tutorial paper provides an introduction, from a systems perspective, to the topic of ship motion dynamics of surface ships. It presents a classification of parametric models currently used for monitoring and control of marine vessels. These models are valid for certain vessel operational...

  5. Space, race, and poverty: Spatial inequalities in walkable neighborhood amenities?

    Directory of Open Access Journals (Sweden)

    John Whalen

    2012-05-01

    Full Text Available BACKGROUND Multiple and varied benefits have been suggested for increased neighborhood walkability. However, spatial inequalities in neighborhood walkability likely exist and may be attributable, in part, to residential segregation. OBJECTIVE Utilizing a spatial demographic perspective, we evaluated potential spatial inequalities in walkable neighborhood amenities across census tracts in Boston, MA (US. METHODS The independent variables included minority racial/ethnic population percentages and percent of families in poverty. Walkable neighborhood amenities were assessed with a composite measure. Spatial autocorrelation in key study variables were first calculated with the Global Moran's I statistic. Then, Spearman correlations between neighborhood socio-demographic characteristics and walkable neighborhood amenities were calculated as well as Spearman correlations accounting for spatial autocorrelation. We fit ordinary least squares (OLS regression and spatial autoregressive models when appropriate as a final step. RESULTS Significant positive spatial autocorrelation was found in neighborhood socio-demographic characteristics (e.g. census tract percent Black, but not walkable neighborhood amenities or in the OLS regression residuals. Spearman correlations between neighborhood socio-demographic characteristics and walkable neighborhood amenities were not statistically significant, nor were neighborhood socio-demographic characteristics significantly associated with walkable neighborhood amenities in OLS regression models. CONCLUSIONS Our results suggest that there is residential segregation in Boston and that spatial inequalities do not necessarily show up using a composite measure. COMMENTS Future research in other geographic areas (including international contexts and using different definitions of neighborhoods (including small-area definitions should evaluate if spatial inequalities are found using composite measures, but also should

  6. Measurement of Lubricating Condition between Swashplate and Shoe in Swashplate Compressors under Practical Operating Conditions

    Science.gov (United States)

    Suzuki, Hisashi; Fukuta, Mitsuhiro; Yanagisawa, Tadashi

    In this paper, lubricating conditions between a swashplate and a shoe in a swashplate compressor for automotive air conditioners is investigated experimentally. The conditions are measured with an electric resistance method that utilizes the swash plate and the shoe as electrodes respectively. The instrumented compressor is connected to an experimental cycle with R134a and operated under various operating conditions of pressure and rotational speed. An improved measurement technique and applying a solid contact ratio to the measurement results permit to measure the lubricating condition at high rotational speed (more than 8000 rpm) and to predic an occurrence of scuffing between the swashplate and the shoe, and therefore enables a detailed study of lubricating characteristics. It is shown by the measurement that the voltage of the contact signal decreases, which means better lubricating condition, with the decrease of the compression pressure and with the increase of the rotational speed from 1000 rpm through 5000 rpm. The lubricating condition tends to worsen at more than 5000 rpm. Furthermore, it is confirmed that the lubricating condition under transient operation is worse obviously as compared with that under steady-state operation.

  7. Dioxins from medical waste incineration: Normal operation and transient conditions.

    Science.gov (United States)

    Chen, Tong; Zhan, Ming-xiu; Yan, Mi; Fu, Jian-ying; Lu, Sheng-yong; Li, Xiao-dong; Yan, Jian-hua; Buekens, Alfons

    2015-07-01

    Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) are key pollutants in waste incineration. At present, incinerator managers and official supervisors focus only on emissions evolving during steady-state operation. Yet, these emissions may considerably be raised during periods of poor combustion, plant shutdown, and especially when starting-up from cold. Until now there were no data on transient emissions from medical (or hospital) waste incineration (MWI). However, MWI is reputed to engender higher emissions than those from municipal solid waste incineration (MSWI). The emission levels in this study recorded for shutdown and start-up, however, were significantly higher: 483 ± 184 ng Nm(-3) (1.47 ± 0.17 ng I-TEQ Nm(-3)) for shutdown and 735 ng Nm(-3) (7.73 ng I-TEQ Nm(-3)) for start-up conditions, respectively. Thus, the average (I-TEQ) concentration during shutdown is 2.6 (3.8) times higher than the average concentration during normal operation, and the average (I-TEQ) concentration during start-up is 4.0 (almost 20) times higher. So monitoring should cover the entire incineration cycle, including start-up, operation and shutdown, rather than optimised operation only. This suggestion is important for medical waste incinerators, as these facilities frequently start up and shut down, because of their small size, or of lacking waste supply. Forthcoming operation should shift towards much longer operating cycles, i.e., a single weekly start-up and shutdown.

  8. Operation of static series compensator under distorted utility conditions

    DEFF Research Database (Denmark)

    Awad, H.; Nelsen, H.; Blaabjerg, Frede

    2005-01-01

    in the case of distorted grid voltage. Furthermore, a selective harmonic compensation strategy is applied to filter out the grid harmonics. The operation of the SSC under distorted utility conditions and voltage dips is discussed. The validity of the proposed controller is verified by experiments, carried out...... on a 10-kV SSC laboratory setup. Experimental results have shown the ability of the SSC to mitigate voltage dips and harmonics. It is also shown that the proposed controller has improved the transient performance of the SSC even under distorted utility conditions....

  9. ANALYSIS OF OPERATING INSTRUMENT LANDING SYSTEM ACCURACY UNDER SIMULATED CONDITIONS

    Directory of Open Access Journals (Sweden)

    Jerzy MERKISZ

    2017-03-01

    Full Text Available The instrument landing system (ILS is the most popular landing aid in the world. It is a distance-angled support system for landing in reduced visibility, while its task is the safe conduct of the aircraft from the prescribed course landing on the approach path. The aim of this study is to analyse the correctness of the ILS in simulated conditions. The study was conducted using a CKAS MotionSim5 flight simulator in the Simulation Research Laboratory of the Institute of Combustion Engines and Transport at Poznan University of Technology. With the advancement of technical equipment, it was possible to check the operation of the system in various weather conditions. Studies have shown that the impact of fog, rain and snow on the correct operation of the system is marginal. Significant influence has been observed, however, during landing in strong winds.

  10. How operant conditioning can contribute to behavioral toxicology

    Energy Technology Data Exchange (ETDEWEB)

    Laties, V.G.

    1978-10-01

    Operant conditioning can contribute to the development of behavioral toxicology in many ways. Its techniques are useful in training animals in the various behaviors the toxicologist may wish to study. They make possible the sophisticated assessment of sensory functioning. Operant conditioners excel at using schedules of intermittent reinforcement to create the type of stable animal performance needed in studying substances that produce effects only after prolonged exposure. Schedule-controlled behavior also helps elucidate the precise behavioral mechanisms involved in toxicity. In the early assessment of toxic substances a judiciously chosen sample of schedule-controlled performances may provide the best estimate whether the integrity of complex operant behavior remains unchanged. The development of improved behavioral techniques and computer technology promises to bring down the cost of such assessment.

  11. Operating Conditions Effects Onenzyme Activity: Case Enzyme Protease

    Directory of Open Access Journals (Sweden)

    Adel Oueslati

    2014-09-01

    Full Text Available The Proteases an enzyme added to detergents to degrade the protein spots origin.Their action is manifested through its activity the middle of washing clothes. This activity depends on the operating conditions. In this article, the effects of temperature and pH of the reaction and the substrate concentration and time of washing medium on the enzyme activity were studied. There action mechanism has been shown. The activity measurements were made by absorption spectrometry

  12. The Other Shoe: An Early Operant Conditioning Chamber for Pigeons

    OpenAIRE

    Sakagami, Takayuki; Lattal, Kennon A.

    2016-01-01

    We describe an early operant conditioning chamber fabricated by Harvard University instrument maker Ralph Gerbrands and shipped to Japan in 1952 in response to a request of Professor B. F. Skinner by Japanese psychologists. It is a rare example, perhaps the earliest still physically existing, of such a chamber for use with pigeons. Although the overall structure and many of the components are similar to contemporary pigeon chambers, several differences are noted and contrasted to evolutionary...

  13. Automated Operant Conditioning in the Mouse Home Cage

    Science.gov (United States)

    Francis, Nikolas A.; Kanold, Patrick O.

    2017-01-01

    Recent advances in neuroimaging and genetics have made mice an advantageous animal model for studying the neurophysiology of sensation, cognition, and locomotion. A key benefit of mice is that they provide a large population of test subjects for behavioral screening. Reflex-based assays of hearing in mice, such as the widely used acoustic startle response, are less accurate than operant conditioning in measuring auditory processing. To date, however, there are few cost-effective options for scalable operant conditioning systems. Here, we describe a new system for automated operant conditioning, the Psibox. It is assembled from low cost parts, designed to fit within typical commercial wire-top cages, and allows large numbers of mice to train independently in their home cages on positive reinforcement tasks. We found that groups of mice trained together learned to accurately detect sounds within 2 weeks of training. In addition, individual mice isolated from groups also showed good task performance. The Psibox facilitates high-throughput testing of sensory, motor, and cognitive skills in mice, and provides a readily available animal population for studies ranging from experience-dependent neural plasticity to rodent models of mental disorders. PMID:28298887

  14. ANALYSIS OF OPTIMUM OPERATING MODES OF POWER TRANSFORMERS UNDER OPERATING CONDITIONS

    Directory of Open Access Journals (Sweden)

    I. V. Khomenko

    2016-12-01

    Full Text Available Purpose. The study of parallel operation optimal modes of transformer equipment for a variety of operating conditions: same or different types of transformers, with or without reactive power flows. Methodology. Losses of energy in transformers make 30 % of all losses. Therefore the choice of the economically justified parallel operation of transformers is effective action to reduce losses. Typically, in the calculations of reactive power flows in the transformers are not taken into account. It is interesting to analyze the optimal operating conditions of transformers with and without reactive power flows. Results. Calculations for transformers in distribution networks showed that the inclusion of reactive power flows in transformers significant impact on the calculated optimum regimes of transformers.

  15. Operational modal analysis of vehicle system based on SSI under operational conditions

    Science.gov (United States)

    Zhou, Suxia; Xie, Yunye; Xie, Jilong; Li, Fang

    2010-03-01

    The modal parameters of linear vehicle system are analyzed by the theoretical modal parameter analysis method first, and then SSI based on operational conditions is presented to form the estimation formula of modal parameters of linear vehicle system. At last, the modal parameters of linear vehicle system are identified by SSI after its vibration test under operational conditions, and are simultaneously compared to the results obtained by the theoretical modal parameter analysis method. Comparison results show discrepancies of 0.61~8.32 percent on modal frequencies and 3.86~11.61 percent on modal damping ratios, which implies that SSI based on the operational condition is feasible and effective, and has comparatively higher precision to meet the needs of engineering.

  16. Occupants' Perceptions of Amenity and Efficiency for Verification of Spatial Design Adequacy.

    Science.gov (United States)

    Lee, Sangwon; Wohn, Kwangyun

    2016-01-01

    The best spatial design condition to satisfy the occupancy needs of amenity and efficiency is determined through analyzing the spatial design adequacy (SDA). In this study, the relationship between the space design elements and space on future occupants' perception are analyzed. The thirty-three participants reported their self-evaluated SDA that describes the quality of eight alternative housing living rooms with different spatial factors. The occupants were guided through the perception processing elaboration in order for them to evaluate the actual perception in the real space. The findings demonstrated that the spatial size (e.g., width, depth, and height) is significantly correlated with the overall satisfaction of amenity. It is also found that the spatial shape (e.g., the width-to-depth ratio, the height-to-area ratio, and room shape) may significantly influence the overall satisfaction of efficiency. The findings also demonstrate that the causal relationship between the spatial factors and space is clearly present in the occupants' perception, reflecting the time-sequential characteristics of the actual experience divided into amenity and efficiency. This result indicates that the correlation between the spatial factors and space of SDA under the occupants' perception processing elaboration can be a useful guide to predict the occupancy satisfaction of amenity and efficiency in real spaces.

  17. Effect of operative conditions on a PEFC stack performance

    Energy Technology Data Exchange (ETDEWEB)

    Urbani, Francesco; Barbera, Orazio; Giacoppo, Giosue; Squadrito, Gaetano; Passalacqua, Enza [CNR-ITAE (Istituto di Tecnologie Avanzate per l' Energia ' Nicola Giordano' ), Salita S. Lucia sopra Contesse, 5-98126 Messina (Italy)

    2008-06-15

    The operative conditions influence the performance of a polymer electrolyte fuel cell (PEFC). In particular, when a multi-cell (stack) instead of a single cell is investigated, a proper water management and flow stoichiometric ratio are essential for obtaining high electrical conversion efficiency. In this paper, a five cell air cooled PEM fuel cell stack was designed and realized, and systematic studies on the influence of the reactants humidification have been carried out to optimize the operative conditions. Polarization curves and time test at a fixed current have been conducted for various cathode (RHC) and anode (RHA) inlet humidity conditions. In particular, a small decay and low performance were obtained for RHA and <70% and a considerable decay and low performance for RHA and >70%. A good compromise for water management, in terms of decay and performance, is obtained when a symmetrical RH of 70% was used, because in this case an optimal water balance was probably reached considering that high flow of gases was used. In fact, insufficient water content implies a lower ion conductivity of the membrane whereas excess of water yields to flooding of the electrodes and parasitic losses due to the presence of water in the gas channels. Consequently, these effects lead to a lowering of voltages during lifetime tests. In any case, the cathode RH has a stronger influence on the stack decay compared to the anode one. In the optimal selected conditions of RH a constant and stable power of about 55 W (at 20 A) was obtained during the 15 h of operation. (author)

  18. Hereditary properties of Amenability modulo an ideal of Banach algebras

    Directory of Open Access Journals (Sweden)

    Hamidreza Rahimi

    2014-10-01

    Full Text Available In this paper we investigate some hereditary properties of amenability modulo an ideal of Banach algebras. We show thatif $(e_{\\alpha}_{\\alpha}$ is a bounded approximate identity modulo $I$ of a Banach algebra $A$ and $X$ is a neo-unital modulo $I$, then $(e_{\\alpha}_{\\alpha}$ is a bounded approximate identity for $X$. Moreover we show that amenability modulo an ideal of a Banach algebra $A$ can be only considered by the neo-unital modulo $I$ Banach algebra over $A$

  19. Amenability to dry processing of high ash thermal coal using a pneumatic table

    Institute of Scientific and Technical Information of China (English)

    Dey Shobhana; Gangadhar B.; Gopalkrishna S.J.

    2015-01-01

    High ash thermal coal from India was used to conduct the dry processing of fine coal using a pneumatic table to evolve a techno-economically novel technique. The fine as-received sample having 55.2%ash was subjected to washability studies at variant densities from 1.4 to 2.2 to assess the amenability to separa-tion. The experiments were conducted using a central composite design for assessing the interactive effects of the variable parameters of a pneumatic table on the product yield and ash content. The perfor-mance of the pneumatic table was analyzed in terms of clean coal yield, recovery of combustibles, separation efficiency (Esp) and useful heat value of clean coal. The combustibles of clean coal obtained through a single stage operation at 35% and 38.7% ash were 40% and 63% respectively. However, the two stage processing was more effective in reducing the ash content in the clean coal. The rougher con-centrate generated at higher ash level was subsequently processed in different conditions at 35% ash level, and 58%combustibles could be recovered. Hence, two stage processing increases the combustibles by 18 units and the useful heat value of clean coal increases from 1190 kcal/kg to 3750 kcal/kg.

  20. The Operator's Diagnosis Task under Abnormal Operating Conditions in Industrial Process Plant

    DEFF Research Database (Denmark)

    Goodstein, L.P.; Pedersen, O.M.; Rasmussen, Jens

    1974-01-01

    Analysis of serious accidents in connection with the operation of technical installations demonstrate that the diagnosis task which confronts personnel under non-normal plant conditions is a critical one. This report presents a preliminary outline of characteristic traits connected with the task...

  1. Flux behaviour under different operational conditions in osmosis process

    DEFF Research Database (Denmark)

    Korenak, Jasmina; Zarebska, Agata; Buksek, Hermina;

    the active membrane layer is facing draw solution. Osmosis process can be affected by several factors, such as operating conditions (temperature and cross flow velocity), feed and draw solution properties, and membrane characteristics. These factors can significantly contribute to the efficiency...... of the process itself. In order to implement the osmosis process on an industrial scale, process economy need to be taken into consideration, as well as the desired final product quality. Membrane performance can be evaluated based on the water permeability and the selectivity of the membrane. The permeability...

  2. The Other Shoe: An Early Operant Conditioning Chamber for Pigeons.

    Science.gov (United States)

    Sakagami, Takayuki; Lattal, Kennon A

    2016-05-01

    We describe an early operant conditioning chamber fabricated by Harvard University instrument maker Ralph Gerbrands and shipped to Japan in 1952 in response to a request of Professor B. F. Skinner by Japanese psychologists. It is a rare example, perhaps the earliest still physically existing, of such a chamber for use with pigeons. Although the overall structure and many of the components are similar to contemporary pigeon chambers, several differences are noted and contrasted to evolutionary changes in this most important laboratory tool in the experimental analysis of behavior. The chamber also is testimony to the early internationalization of behavior analysis.

  3. Optimal line drop compensation parameters under multi-operating conditions

    Science.gov (United States)

    Wan, Yuan; Li, Hang; Wang, Kai; He, Zhe

    2017-01-01

    Line Drop Compensation (LDC) is a main function of Reactive Current Compensation (RCC) which is developed to improve voltage stability. While LDC has benefit to voltage, it may deteriorate the small-disturbance rotor angle stability of power system. In present paper, an intelligent algorithm which is combined by Genetic Algorithm (GA) and Backpropagation Neural Network (BPNN) is proposed to optimize parameters of LDC. The objective function proposed in present paper takes consideration of voltage deviation and power system oscillation minimal damping ratio under multi-operating conditions. A simulation based on middle area of Jiangxi province power system is used to demonstrate the intelligent algorithm. The optimization result shows that coordinate optimized parameters can meet the multioperating conditions requirement and improve voltage stability as much as possible while guaranteeing enough damping ratio.

  4. A discrete-space urban model with environmental amenities

    Science.gov (United States)

    Liaila Tajibaeva; Robert G. Haight; Stephen Polasky

    2008-01-01

    This paper analyzes the effects of providing environmental amenities associated with open space in a discrete-space urban model and characterizes optimal provision of open space across a metropolitan area. The discrete-space model assumes distinct neighborhoods in which developable land is homogeneous within a neighborhood but heterogeneous across neighborhoods. Open...

  5. Moderate induced hypotension provides satisfactory operating conditions in maxillofacial surgery.

    Science.gov (United States)

    Schindler, I; Andel, H; Leber, J; Kimla, T

    1994-05-01

    Patients scheduled for maxillofacial surgery were randomly assigned to receive isoflurane (n = 22) or nitroglycerin (n = 18) in order to induce hypotension. Surgeons, blinded for the actual level of blood pressure and the technique used for inducing hypotension, were asked to rate operating conditions on a scale from 1 to 5. Systolic arterial pressure (SAP) and mean arterial pressure (MAP) were reduced by 26% for both groups. Although blood pressure levels showed little variation throughout the induced hypotension period, scores of 2 to 5 were given significantly more often at incision and at 30 min compared to the following measuring points (P < 0.01). In total, the surgical field was rated significantly more often with a score of 1 and 2 than with a score of 3 to 5 (P < 0.01). A relation between score and SAP and/or MAP could not be found. There was also no relation between scores and the technique used for hypotension. Our data suggest that, with the exception of the first half hour of surgery, on average a SAP of 89 mmHg and a MAP of 65 mmHg were sufficient to produce satisfactory operating conditions.

  6. Quantifying Social Motivation in Mice Using Operant Conditioning.

    Science.gov (United States)

    Martin, Loren; Iceberg, Erica

    2015-08-08

    In this protocol, social motivation is measured in mice through a pair of operant conditioning paradigms. To conduct the experiments, two-chambered shuttle boxes were equipped with two operant levers (left and right) and a food receptacle in one chamber, which was then divided from the second chamber by an automated guillotine door covered by a wire grid. Different stimulus mice, rotated across testing days, served as a social stimulus behind the wire grid, and were only visible following the opening of the guillotine door. Test mice were trained to lever press in order to open the door and gain access to the stimulus partner for 15 sec. The number of lever presses required to obtain the social reward progressively increased on a fixed schedule of 3. Testing sessions ended after test mice stopped lever pressing for 5 consecutive minutes. The last reinforced ratio or breakpoint can be used as a quantitative measure of social motivation. For the second paradigm, test mice were trained to discriminate between left and right lever presses in order to obtain either a food reward or the social reward. Mice were rewarded for every 3 presses of each respective lever. The number of food and social rewards can be compared as a measurement of the value placed upon each reward. The ratio of each reward type can also be compared between mouse strains and the change in this ratio can be monitored within testing sessions to measure satiation with a given reward type. Both of these operant conditioning paradigms are highly useful for the quantification of social motivation in mouse models of autism and other disorders of social behavior.

  7. Simulation of gas turbines operating in off-design condition

    Energy Technology Data Exchange (ETDEWEB)

    Walter, Arnaldo [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica. Dept. de Energia]. E-mail: walter@fem.unicamp.br

    2000-07-01

    In many countries thermal power plants based on gas turbines have been the main option for new investment into the electric system due to their relatively high efficiency and low capital cost. Cogeneration systems based on gas turbines have also been an important option for the electric industry. Feasibility studies of power plants based on gas turbine should consider the effect of atmospheric conditions and part-load operation on the machine performance. Doing this, an off-design procedure is required. A G T off-design simulation procedure is described in this paper. Ruston R M was used to validate the simulation procedure that, general sense, presents deviations lower than 2.5% in comparison to manufacturer's data. (author)

  8. Effect of Operating Conditions on CSTR performance: an Experimental Study

    Directory of Open Access Journals (Sweden)

    Mohd Danish

    2015-02-01

    Full Text Available In this work, Saponification reaction of ethyl acetate by sodium hydroxide is studied experimentally in a continuous stirred tank reactor at 1 atmospheric pressure. The aim of this study is to investigate the influence of operating conditions on the conversion and specific rate constant. The parameters considered for analysis are temperature, feed flow rate, residence time, volume of reactor and stirrer rate. The steady state conversion of 0.45 achieved after a period of 30 minutes. Conversion decreases with increase of reactant flow rate due to decrease of residence time. The stirrer rate has a positive effect on the conversion and rate constant. Specific rate constant and conversion increase with temperature within the studied temperature range. Within the range of reactor volume selected for analysis, conversion increases with increase in reactor volume. The results obtained in this study may be helpful in maximizing the conversion of ethyl acetate saponification reaction at industrial scale in a CSTR.

  9. Effects of Operational Conditions on the Performance of Triethylamine Biofiltration

    Directory of Open Access Journals (Sweden)

    A Torkian, H Keshavarzi Shirazi, A Azimi

    2005-04-01

    Full Text Available Nitrogen compounds such as triethylamine are odorants generally found in chemical plants and foundries in which cold-box cores are made. In this study, the efficiency of biofiltration of triethylamine (TEA vapor was evaluated. Experiments were conducted in two 6-L biofilters arranged in three stages and packed with inoculated compost - wood chips (40:60v/v as the filter medium. The seed inoculum was obtained from municipal activated sludge. Tests were made to compare effects of initial temperature (30±1°C, biofilter A and (23±2 °C, biofilter B on the performance of the biofilter. TEA elimination rate pattern was evaluated by changing loading rates (6-138 gm-3h-1 and hydraulic retention times (40-60 s while operating at constant temperature and humidity at 50-55%. Results showed that organic loading rates (OLR of up to 114.4 gm-3h-1 (biofilter A and 90.56 gm-3h-1 (biofilter B could be handled without any apparent indication of maximum elimination capacity and substrate inhibition. The elimination capacity of biofilters could reach up to 72 gm-3h-1 (biofilter A and 61.5 gm-3h-1(biofilter B. When the loading of TEA exceeded the critical values, substrate inhibition occurred and the elimination capacity decreased. However, the requirement of keeping the pressure drop below 4 cm water gauge per meter of bed height to avoid operational problems warranted lower than maximum capacity operation. The optimal OLR values of 90±14 gm-3h-1 are suggested for hydraulic retention time value of 48 s and temperature of 30±1°C. Under these conditions, elimination capacity of 71±3 gm-3h-1and removal efficiency of 81±14% was achieved.

  10. Wealth Financialization: Operating Profit as Conditioning of Financial Revenue

    Directory of Open Access Journals (Sweden)

    Andréia Ribeiro Da Luz

    2015-04-01

    Full Text Available Objective. Due to the deregulation of the financial market in 80s decade, the financialization of wealth has become a globalized systemic pattern, giving companies greater access to financial innovations. In view of the above, the objective is to analyze whether the appreciation of capital through the financial system is preferred over the capital appreciation through production.Methodology. This is a descriptive research slitting with cross-sectional perspective, in which we considered information belonging to 106 listed non-financial companies in Brazil (2004–2012.Findings. This study suggests that operating income influences financial income positively.Limitations. The study includes just industrial sector companies in a specific period.Originality/Value. We discuss measuring instruments for analyzing the wealth financialization as a condition of operating profit gains from the financial market.Copyright © 2015 Instituto Brasileiro de Inovação Financeira All rights reserved.

  11. Moderating role of interior amenities on hospital medical directors' patient-related work stresses.

    Science.gov (United States)

    Lin, Blossom Yen-Ju; Lin, Yung-Kai; Juan, Chi Wen; Lee, Suhsing; Lin, Cheng-Chieh

    2013-01-01

    Considering hospital medical directors' work stress, this study aims to examine how interior amenities might moderate the effect of work stress on their health. Previous studies have revealed that hospital medical directors-senior physicians in the management positions with high-demand jobs in clinical practices and management-had a lower self-rated health. This was a cross-sectional survey study and 737 hospital medical directors in Taiwan were included. A developed and structured questionnaire covered the dimensions of patient-related work stress (i.e., physician-patient relationship stress and patient condition stress), hospital interior amenities (i.e., indoor plants, aquarium, music, art and exhibitions, and private or personalized spaces that are common or surround the workplace of healthcare professionals), and self-rated health status and health complaints. Hierarchical regressions were performed. Hospital medical directors' physician-patient relationship stresses were found to have more negative effects on their self-reported health status and complaints than do their patient condition stresses; however, only indoor plants were found to have moderating effects on their short-term health complaints (p interior amenities can produce buffering effects on work stress to some extent. Future studies could focus on finding alternatives to relieve hospital medical directors' physician-patient relationship work stresses. Evidence-based design, physicians, privacy and security, satisfaction, work environmentPreferred Citation: Lin, B. Y.-J., Lin, Y.-K., Juan, C.W., Lee, S., Lin, C.-C. (2013). Moderating role of interior amenities on hospital medical directors' patient-related work stresses. Health Environments Research & Design Journal 6(2), pp 77-92.

  12. Do we need another coffee house? The amenity space and the evolution of neighborhoods

    CERN Document Server

    Hidalgo, César A

    2015-01-01

    Neighborhoods populated by amenities, such as restaurants, cafes, and libraries, are considered to be a key property of desirable cities. Yet, despite the global enthusiasm for amenity-rich neighborhoods, little is known about the empirical laws governing the colocation of amenities at the neighborhood scale. Here, we contribute to our understanding of the naturally occurring neighborhood-scale agglomerations of amenities observed in cities by using a dataset summarizing the precise location of millions of amenities. We use this dataset to build the network of co-location of amenities, or Amenity Space, by first introducing a clustering algorithm to identify neighborhoods, and then using the identified neighborhoods to map the probability that two amenities will be co-located in one of them. Finally, we use the Amenity Space to build a recommender system that identifies the amenities that are missing in a neighborhood given its current pattern of specialization. This opens the door for the construction of ame...

  13. Textiles, body care products, amenity horticulture and energy production

    OpenAIRE

    2014-01-01

    Food production is the most evident result of Organic Farming. However, farm products are used for other human needs. Some of those Organic sectors beyond food, e.g. the amenity horticulture are in an early stage of development, but have big potentials. Awareness inside and outside of the Organic world and development of the value chain need to be further developed. Other Organic sectors beyond food, e.g. Organic cotton have made impressive progress during the past few years.

  14. The amenability of the substitution group of formal power series

    Energy Technology Data Exchange (ETDEWEB)

    Babenko, Ivan K; Bogatyi, Semen A

    2011-04-30

    We study the amenability property for the group J(k) of formal power series in one variable with coefficients in a commutative ring k with identity. We show that there exists an invariant mean on the space C{sub u}*(J(k)) of uniformly continuous bounded functions on this group. This is equivalent to the fact that every continuous action of J(k) on every compact space has an invariant probability measure.

  15. Effect of circadian phase on memory acquisition and recall: operant conditioning vs. classical conditioning.

    Directory of Open Access Journals (Sweden)

    Madeleine V Garren

    Full Text Available There have been several studies on the role of circadian clocks in the regulation of associative learning and memory processes in both vertebrate and invertebrate species. The results have been quite variable and at present it is unclear to what extent the variability observed reflects species differences or differences in methodology. Previous results have shown that following differential classical conditioning in the cockroach, Rhyparobia maderae, in an olfactory discrimination task, formation of the short-term and long-term memory is under strict circadian control. In contrast, there appeared to be no circadian regulation of the ability to recall established memories. In the present study, we show that following operant conditioning of the same species in a very similar olfactory discrimination task, there is no impact of the circadian system on either short-term or long-term memory formation. On the other hand, ability to recall established memories is strongly tied to the circadian phase of training. On the basis of these data and those previously reported for phylogenetically diverse species, it is suggested that there may be fundamental differences in the way the circadian system regulates learning and memory in classical and operant conditioning.

  16. The operating room: architectural conditions and potential hazards.

    Science.gov (United States)

    Koneczny, Sonja

    2009-01-01

    Ergonomics is still not fully implemented in the design of operation rooms (ORs). The OR staff has to deal with various ergonomic deficiencies which may be associated with potential hazards for the patient and/or the OR team.Three surveys were conducted among German OR staff at major conferences. Two of them dealt with the working conditions in the OR and were conducted among surgeons and OR nurses. The third survey queried OR nurses about the electrical safety in the OR.In addition, a specially developed checklist was used to evaluate the work place OR in five German OR units and the staff of these OR units were queried with questionnaires adapted from the surveys. For this article a few of the deficiencies found in the ORs were chosen to serve as examples for the plethora of results gathered.Findings showed that there was a high potential for ergonomic improvement and therefore an increase in safety and comfort. Many of these deficiencies may be eased by simple means such as the reduction of the number of different devices and mandatory training in the use of the devices since device operation is one of the main causes leading to potential hazards in the OR. Other deficiencies, such as the cable routing in the OR, require more extensive intervention and/or the implementation of new techniques, for example the "wireless" OR. All these deficiencies demonstrate the need for better implementation of ergonomics into the OR and for individual solutions, as there is no such thing as an 'one-size-fits-all' solution for OR units.

  17. Chemical imaging of Fischer-Tropsch catalysts under operating conditions

    Science.gov (United States)

    Price, Stephen W. T.; Martin, David J.; Parsons, Aaron D.; Sławiński, Wojciech A.; Vamvakeros, Antonios; Keylock, Stephen J.; Beale, Andrew M.; Mosselmans, J. Frederick W.

    2017-01-01

    Although we often understand empirically what constitutes an active catalyst, there is still much to be understood fundamentally about how catalytic performance is influenced by formulation. Catalysts are often designed to have a microstructure and nanostructure that can influence performance but that is rarely considered when correlating structure with function. Fischer-Tropsch synthesis (FTS) is a well-known and potentially sustainable technology for converting synthetic natural gas (“syngas”: CO + H2) into functional hydrocarbons, such as sulfur- and aromatic-free fuel and high-value wax products. FTS catalysts typically contain Co or Fe nanoparticles, which are often optimized in terms of size/composition for a particular catalytic performance. We use a novel, “multimodal” tomographic approach to studying active Co-based catalysts under operando conditions, revealing how a simple parameter, such as the order of addition of metal precursors and promoters, affects the spatial distribution of the elements as well as their physicochemical properties, that is, crystalline phase and crystallite size during catalyst activation and operation. We show in particular how the order of addition affects the crystallinity of the TiO2 anatase phase, which in turn leads to the formation of highly intergrown cubic close-packed/hexagonal close-packed Co nanoparticles that are very reactive, exhibiting high CO conversion. This work highlights the importance of operando microtomography to understand the evolution of chemical species and their spatial distribution before any concrete understanding of impact on catalytic performance can be realized. PMID:28345057

  18. Action Selection and Operant Conditioning: A Neurorobotic Implementation

    Directory of Open Access Journals (Sweden)

    André Cyr

    2015-01-01

    Full Text Available Action selection (AS is thought to represent the mechanism involved by natural agents when deciding what should be the next move or action. Is there a functional elementary core sustaining this cognitive process? Could we reproduce the mechanism with an artificial agent and more specifically in a neurorobotic paradigm? Unsupervised autonomous robots may require a decision-making skill to evolve in the real world and the bioinspired approach is the avenue explored through this paper. We propose simulating an AS process by using a small spiking neural network (SNN as the lower neural organisms, in order to control virtual and physical robots. We base our AS process on a simple central pattern generator (CPG, decision neurons, sensory neurons, and motor neurons as the main circuit components. As novelty, this study targets a specific operant conditioning (OC context which is relevant in an AS process; choices do influence future sensory feedback. Using a simple adaptive scenario, we show the complementarity interaction of both phenomena. We also suggest that this AS kernel could be a fast track model to efficiently design complex SNN which include a growing number of input stimuli and motor outputs. Our results demonstrate that merging AS and OC brings flexibility to the behavior in generic dynamical situations.

  19. Mobility and Cloud: Operating in Intermittent, Austere Network Conditions

    Science.gov (United States)

    2014-09-01

    35 viii 2. Piracy Interdiction Use Case.............................................................38 E...38 Figure 11. Operational view: Piracy interdiction operation. .............................................40...Storage Service SAR Search and Rescue SATCOM satellite communications SIPRNET Secret Internet Protocol Router Network SSAS Ship Security Alert System

  20. On the resolvent of multidimensional operators with frequently changing boundary conditions in the case of the homogenized Dirichlet condition

    Energy Technology Data Exchange (ETDEWEB)

    Sharapov, T F [Bashkir State Pedagogical University, Ufa (Russian Federation)

    2014-10-31

    We consider an elliptic operator in a multidimensional domain with frequently changing boundary conditions in the case when the homogenized operator contains the Dirichlet boundary condition. We prove the uniform resolvent convergence of the perturbed operator to the homogenized operator and obtain estimates for the rate of convergence. A complete asymptotic expansion is constructed for the resolvent when it acts on sufficiently smooth functions. Bibliography: 41 titles.

  1. Rapid detection of pesticides not amenable to multi-residue methods by flow injection-tandem mass spectrometry

    NARCIS (Netherlands)

    Mol, J.G.J.; Dam, van R.C.J.

    2014-01-01

    Flow injection combined with tandem mass spectrometry (MS/MS) was investigated for the rapid detection of highly polar pesticides that are not amenable to multi-residue methods because they do not partition into organic solvents and require dedicated chromatographic conditions. The pesticides includ

  2. The Last Adventure: Retirement Migration, Climate and "Amenities"

    Directory of Open Access Journals (Sweden)

    Saša Božić

    2001-12-01

    Full Text Available The rising number of European retirement migrants on the Mediterranean coasts, especially in the EU countries shows that the practical and scientific relevance of the new forms of migration in Europe is on the rise. "Retirement migration" evolved from a descriptive term to a candidate for a scientific or a research concept, at least if the use of the term IRM (international retirement migration is considered. However, it is necessary to solve several problems before this term can really become a coherent concept, useful for the research and explanation of the "new" migration phenomena. The author claims that the studies usually do not distinguish clearly between the migration of the elderly and retirement migration. The naming of the concept in this case mixes the characteristics of the migrants with the reasons for migration. The author shows that the usually mentioned reasons for retirement migration cannot be clearly formulated as factors which explain retirement migration. Further on, retirement as such is not a pull, push or staying put factor. Migration rates of retired, although rising, are still lower than the migration rates of the working age population and the Mediterranean coasts are also a destination for professionals who have the means to detach the job from the working place. Only a combination of conditions that enable migration and migration decisions, as well as a combination of motives and perceptions of reasons for migration, can partially "explain" retirement migration. One of the problems that has to be solved before retirement migration is affirmed as a concept is the treatment of the temporal and spatial dimension of the mobility of the retirement migrants. The author shows that a clear positioning of retirement migration on the temporal scale of mobility is hardly possible. Retirement migration is too wide and too complex a phenomenon to be easily localised in the temporal continuum. A similar problem emerges when the

  3. Fluidized-bed reactors processes and operating conditions

    CERN Document Server

    Yates, John G

    2016-01-01

    The fluidized-bed reactor is the centerpiece of industrial fluidization processes. This book focuses on the design and operation of fluidized beds in many different industrial processes, emphasizing the rationale for choosing fluidized beds for each particular process. The book starts with a brief history of fluidization from its inception in the 1940’s. The authors present both the fluid dynamics of gas-solid fluidized beds and the extensive experimental studies of operating systems and they set them in the context of operating processes that use fluid-bed reactors. Chemical engineering students and postdocs as well as practicing engineers will find great interest in this book.

  4. Study of safety relief valve operation under ATWS conditions. [PWR

    Energy Technology Data Exchange (ETDEWEB)

    Hutmacher, E.S.; Nesmith, B.J.; Brukiewa, J.B.

    1979-06-25

    A literature survey and analysis project has been performed to determine if recent (since mid-1975) data has been reported which could influence the current approach to predicting PWR relief valve capacity under ATWS conditions. This study was conducted by the Energy Technology Engineering Center for NRC. Results indicate that the current relief valve capacity model tends to predict less capacity than actually obtains; however, no experimental verification at PWR ATWS conditions was found. Other project objectives were to establish the availability of methods for evaluating reaction forces and back pressure effects on relief valve capacity, and to determine if facilities exist which are capable of testing PWR relief valves at ATWS conditions.

  5. Amenability of Muzret bituminous coal to oil agglomeration

    Energy Technology Data Exchange (ETDEWEB)

    Sahinoglu, E.; Uslu, T. [Karadeniz Technical University, Department of Mining Engineering, 61080 Trabzon (Turkey)

    2008-12-15

    Laboratory scale agglomeration tests were undertaken to investigate the amenability of Muzret (Yusufeli-Artvin) bituminous coal to oil agglomeration. Kerosene was extensively used as oil in the tests. In addition, fuel oil, diesel oil, and hazelnut oil were also used in order to determine the effect of oil type. The effects of the parameters including coal content, kerosene content, agglomeration time, coal particle size, pH, oil type, and agitation rate, on the combustible matter recovery, ash reduction and pyritic sulphur reduction, were investigated. It was found that Muzret bituminous coal could be readily cleaned by oil agglomeration with substantial reductions in ash and pyritic sulphur content. Maximum combustible matter recovery, ash reduction and pyritic sulphur reduction were achieved to be 85.54%, 59.98%, and 85.17%, respectively. (author)

  6. Carolinas HealthCare attends to patients, amenities; builds business.

    Science.gov (United States)

    Rees, T

    2000-01-01

    Carolinas HealthCare System has grown into a nearly two billion dollar entity by focusing on patient needs and amenities in its health care facilities. Growth of the system, the largest in North and South Carolina, is due in large part to Harry A. Nurkin, president and CEO, who started out with a run-down hospital for indigents. With the approval of the hospital board, Nurkin launched a marketing effort that included taking a lesson from the founders of the Holiday Inn hotel chain. He remodeled and developed facilities that are pleasing to patients and visitors, moved patient parking closer to the hospitals' front doors, taught key hospital personnel the basics about marketing, aligned the system with ABA and NFL teams and conducted an aggressive advertising program.

  7. Welded repair joints of boiler steels following operation in creep conditions exceeding the design time of operation

    Energy Technology Data Exchange (ETDEWEB)

    Dobrzanski, J.; Paszkowska, H.; Zielinski, A. [Institute for Ferrous Metallurgy, Gliwice (Poland)

    2010-07-01

    The assessment of suitability for further operation for materials and welded repair joints of thick-walled main steam pipeline components, made of steel 14MoV63, as well as steam superheater outlet headers made of steel X20CrMoV121 following operation in creep conditions in time periods considerably longer than the specified calculated time of operation. Strength properties, impact strength and transition temperature into brittle condition, as well as structure condition have been evaluated. On the basis of shortened creep tests, the residual life and disposable residual life of materials and welded joints have been determined. Material properties following operation and those of fabricated circumferential welded repair joints have been compared. The condition of examined components and suitability of the fabricated welded repair joints for further operation have been assessed. (orig.)

  8. 14 CFR 91.527 - Operating in icing conditions.

    Science.gov (United States)

    2010-01-01

    ...-Powered Multiengine Airplanes and Fractional Ownership Program Aircraft § 91.527 Operating in icing... adhering to the wings or stabilizing or control surfaces; or (3) Any frost adhering to the wings or... Aviation Regulation No. 23, or those for transport category airplane type certification, no pilot may...

  9. Operation Design of Wind Turbines in Strong Wind Conditions

    DEFF Research Database (Denmark)

    Shen, Wen Zhong; Montes, Melissa Barroso; Odgaard, Peter Fogh

    2012-01-01

    In order to reduce the impact on the electrical grid from the shutdown of MW wind turbines at wind speeds higher than the cut-out wind speed of 25 m/s, we propose in this paper to run the turbines at high wind speeds up to 40 m/s. Two different operation designs are made for both constant speed...

  10. Remaining useful life estimation for deteriorating systems with time-varying operational conditions and condition-specific failure zones

    Institute of Scientific and Technical Information of China (English)

    Li Qi; Gao Zhanbao; Tang Diyin; Li Baoan

    2016-01-01

    Dynamic time-varying operational conditions pose great challenge to the estimation of system remaining useful life (RUL) for the deteriorating systems. This paper presents a method based on probabilistic and stochastic approaches to estimate system RUL for periodically moni-tored degradation processes with dynamic time-varying operational conditions and condition-specific failure zones. The method assumes that the degradation rate is influenced by specific oper-ational condition and moreover, the transition between different operational conditions plays the most important role in affecting the degradation process. These operational conditions are assumed to evolve as a discrete-time Markov chain (DTMC). The failure thresholds are also determined by specific operational conditions and described as different failure zones. The 2008 PHM Conference Challenge Data is utilized to illustrate our method, which contains mass sensory signals related to the degradation process of a commercial turbofan engine. The RUL estimation method using the sensor measurements of a single sensor was first developed, and then multiple vital sensors were selected through a particular optimization procedure in order to increase the prediction accuracy. The effectiveness and advantages of the proposed method are presented in a comparison with exist-ing methods for the same dataset.

  11. Model Skinner Operant Conditioning automata i bionički naučeno upravljanje robota

    OpenAIRE

    Cai, Jianxian; Hong, Li; Cheng, Lina; Yu, Ruihong

    2016-01-01

    Fuzzy Skinner Operant Conditioning Automaton (FSOCA) sastavljen je na temelju Operant Conditioning mehanizma primjenom teorije neizrazitih skupova. Osnovno obilježje automata FSOCA je sljedeće: neizraziti rezultati stanja pomoću Gausove funkcije koriste se kao skupovi neizrazitog stanja; neizrazita pravila preslikavanja (fuzzy mapping rules) kod fuzzy-conditioning-operacije zamjenjuju stohastičke "conditioning-operant" skupove preslikavanja. Stoga se automat FSOCA može koristiti za opisivanje...

  12. [Design, equipment, and management for air conditioning in operating room].

    Science.gov (United States)

    Fuji, Kumiko; Mizuno, Ju

    2011-11-01

    In order to maintain air cleanliness in the operating room (OR) permanently, air exchange rate in the OR should be more than 15 times x hr(-1), the laminar air flow should be kept, and the numbers of the persons in the OR and the numbers of opening and closing OR door should be limited. High efficiency particulate air (HEPA) filter is effective in collection and removal of airborne microbes, and is used in the biological clean room. We need to design, equip, and manage the OR environment according to Guideline for Design and Operation of Hospital HVAC Systems HEAS-02-2004 established by Healthcare Engineering Association of Japan and Guideline for Prevention of Surgical Site Infection (SSI) established by the Center for Disease Control and Prevention (CDC) in the USA.

  13. Skinner boxes for psychotics: Operant conditioning at Metropolitan state hospital

    OpenAIRE

    Rutherford, Alexandra

    2003-01-01

    Between 1953 and 1965, Ogden Lindsley and his associates conducted free-operant research with psychiatric inpatients and normal volunteers at Metropolitan State Hospital in Waltham, Massachusetts. Their project, originally named “Studies in Behavior Therapy,” was renamed “Harvard Medical School Behavior Research Laboratory” in 1955. This name change and its implications were significant. The role of the laboratory in the history of the relationship between the experimental analysis of behavio...

  14. Sleep Supports Inhibitory Operant Conditioning Memory in "Aplysia"

    Science.gov (United States)

    Vorster, Albrecht P. A.; Born, Jan

    2017-01-01

    Sleep supports memory consolidation as shown in mammals and invertebrates such as bees and "Drosophila." Here, we show that sleep's memory function is preserved in "Aplysia californica" with an even simpler nervous system. Animals performed on an inhibitory conditioning task ("learning that a food is inedible") three…

  15. Remaining useful life estimation for deteriorating systems with time-varying operational conditions and condition-specific failure zones

    Directory of Open Access Journals (Sweden)

    Li Qi

    2016-06-01

    Full Text Available Dynamic time-varying operational conditions pose great challenge to the estimation of system remaining useful life (RUL for the deteriorating systems. This paper presents a method based on probabilistic and stochastic approaches to estimate system RUL for periodically monitored degradation processes with dynamic time-varying operational conditions and condition-specific failure zones. The method assumes that the degradation rate is influenced by specific operational condition and moreover, the transition between different operational conditions plays the most important role in affecting the degradation process. These operational conditions are assumed to evolve as a discrete-time Markov chain (DTMC. The failure thresholds are also determined by specific operational conditions and described as different failure zones. The 2008 PHM Conference Challenge Data is utilized to illustrate our method, which contains mass sensory signals related to the degradation process of a commercial turbofan engine. The RUL estimation method using the sensor measurements of a single sensor was first developed, and then multiple vital sensors were selected through a particular optimization procedure in order to increase the prediction accuracy. The effectiveness and advantages of the proposed method are presented in a comparison with existing methods for the same dataset.

  16. Modal test results of a ship under operational conditions

    DEFF Research Database (Denmark)

    Orlowitz, Esben; Brandt, Anders

    2014-01-01

    Skibe er udsat for et komplekst vibration miljø, påvirket af havet, samt driftsforholdene. Især er det vanskeligt at anslå analytisk værdier for de hydrodynamiske påvirkninger. Eksperimentelle resultater er derfor vigtigt for at kontrollere de analytiske modeller. I den foreliggende artikel præse...... fokuserer på driftsforhold påvirkning af de modal parametre og viser en betydelig variation af modal dæmpning af skibet i drift, med cirka 400%, 200% og 400% forskel i de første tre globale lodrette bøjning modes, ved forskellige operations hastigheder....

  17. Extending In Vitro Conditioning in "Aplysia" to Analyze Operant and Classical Processes in the Same Preparation

    Science.gov (United States)

    Brembs, Bjorn; Baxter, Douglas A.; Byrne, John H.

    2004-01-01

    Operant and classical conditioning are major processes shaping behavioral responses in all animals. Although the understanding of the mechanisms of classical conditioning has expanded significantly, the understanding of the mechanisms of operant conditioning is more limited. Recent developments in "Aplysia" are helping to narrow the gap in the…

  18. Influence of impurity gases and operating conditions on PAFC performance

    Energy Technology Data Exchange (ETDEWEB)

    Hirai, K.; Iwasa, N.; Suzuki, M.; Okada, O. [Osaka Gas Co., Ltd. (Japan)] [and others

    1996-12-31

    On-site Phosphoric Acid Fuel Cell (PAFC) Cogeneration system is installed at various test sites, such as at underground parking lot, within chemical plant premises and near urban streets. Since in the current PAFC system, cathode air is supplied to the cell with no particular pretreatment, impurity gases in the air might influence on cell performance. We have investigated the influence of various impurity gases in the cathode gas, on sub-scale single cells, and have found that NO{sub 2}, SO{sub 2} and toluene affect negatively on cell performance. The results of these experiments and the conceivable mechanism of these effects on cell degradation are reported. We have also investigated the influence of other operating parameters, such as temperature, current density, fuel utilization on cell performance. From these experiments, we have found that operating temperature is a significant factor, which mainly determines cell voltage decline rate. The results of sub-scale single cell tests and a short-stack verification test are also reported.

  19. The operant and the classical in conditioned orientation of Drosophila melanogaster at the flight simulator.

    Science.gov (United States)

    Brembs, B; Heisenberg, M

    2000-01-01

    Ever since learning and memory have been studied experimentally, the relationship between operant and classical conditioning has been controversial. Operant conditioning is any form of conditioning that essentially depends on the animal's behavior. It relies on operant behavior. A motor output is called operant if it controls a sensory variable. The Drosophila flight simulator, in which the relevant behavior is a single motor variable (yaw torque), fully separates the operant and classical components of a complex conditioning task. In this paradigm a tethered fly learns, operantly or classically, to prefer and avoid certain flight orientations in relation to the surrounding panorama. Yaw torque is recorded and, in the operant mode, controls the panorama. Using a yoked control, we show that classical pattern learning necessitates more extensive training than operant pattern learning. We compare in detail the microstructure of yaw torque after classical and operant training but find no evidence for acquired behavioral traits after operant conditioning that might explain this difference. We therefore conclude that the operant behavior has a facilitating effect on the classical training. In addition, we show that an operantly learned stimulus is successfully transferred from the behavior of the training to a different behavior. This result unequivocally demonstrates that during operant conditioning classical associations can be formed.

  20. The Operant and the Classical in Conditioned Orientation of Drosophila melanogaster at the Flight Simulator

    Science.gov (United States)

    Brembs, Björn; Heisenberg, Martin

    2000-01-01

    Ever since learning and memory have been studied experimentally, the relationship between operant and classical conditioning has been controversial. Operant conditioning is any form of conditioning that essentially depends on the animal's behavior. It relies on operant behavior. A motor output is called operant if it controls a sensory variable. The Drosophila flight simulator, in which the relevant behavior is a single motor variable (yaw torque), fully separates the operant and classical components of a complex conditioning task. In this paradigm a tethered fly learns, operantly or classically, to prefer and avoid certain flight orientations in relation to the surrounding panorama. Yaw torque is recorded and, in the operant mode, controls the panorama. Using a yoked control, we show that classical pattern learning necessitates more extensive training than operant pattern learning. We compare in detail the microstructure of yaw torque after classical and operant training but find no evidence for acquired behavioral traits after operant conditioning that might explain this difference. We therefore conclude that the operant behavior has a facilitating effect on the classical training. In addition, we show that an operantly learned stimulus is successfully transferred from the behavior of the training to a different behavior. This result unequivocally demonstrates that during operant conditioning classical associations can be formed. PMID:10753977

  1. The dynamic behavior of sliding tribosystems in unstable operating conditions

    Science.gov (United States)

    Postaru, A.; Postaru, Ghe; Ceban, V.; Spânu, C.; Stoicev, P.

    2017-02-01

    The paper addresses the issue of the influence that the law of friction has on the dynamic behavior of the mechanical system that interacts with a tribosystem. The emergence of certain nonlinearities of higher order into the law of friction leads to an intensification of the dissipative process and to tribosystem destabilization. Consequently, friction excited self-oscillations are generated into the elements of the mechanical system with a wide spectrum of frequencies, sustained from the external source of energy. The theoretical and experimental modelling of the dissipative process and of the generation of is based on the frictional harmonic oscillator that interacts with the tribosystem. The oscillator is used as a sensitive element to the fluctuations of the frictional force and as a measure of the dissipated energy. Starting from the model, the elaboration of a method and of devices for experimental research provided the opportunity to study the behavior of the tribosystem in unstable operating

  2. Skinner boxes for psychotics: operant conditioning at Metropolitan State Hospital.

    Science.gov (United States)

    Rutherford, Alexandra

    2003-01-01

    Between 1953 and 1965, Ogden Lindsley and his associates conducted free-operant research with psychiatric inpatients and normal volunteers at Metropolitan State Hospital in Waltham, Massachusetts. Their project, originally named "Studies in Behavior Therapy," was renamed "Harvard Medical School Behavior Research Laboratory" in 1955. This name change and its implications were significant. The role of the laboratory in the history of the relationship between the experimental analysis of behavior and applied behavior analysis is discussed. A case is made for viewing Lindsley's early work as foundational for the subfield of the experimental analysis of human behavior that formally coalesced in the early 1980s. The laboratory's work is also contextualized with reference to the psychopharmacological revolution of the 1950s. Finally, a four-stage framework for studying the historical and conceptual development of behavior analysis is proposed.

  3. Operating conditions of batteries in off-grid renewable energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Svoboda, Vojtech [University of Hawaii, 1680 East-West Rd., Post 109, Honolulu, HI 96822, (United States); Wenzl, Heinz [Beratung fuer Batterien und Energietechnik, Am Bergwaeldchen 27, 37520 Osterode (Germany); Kaiser, Rudi [Fraunhofer Institute for Solar Energy Systems, Heidenhofstrasse 2, 79110 Freiburg (Germany); Jossen, Andreas [Center for Solar Energy and Hydrogen Research Baden - Wuerttemberg, Helmholtzstrasse 8, 89081 Ulm (Germany); Baring-Gould, Ian [National Renewable Energy Laboratory, MS 3811, 1617 Cole Blvd, 80401-3393 Golden/CO (United States); Manwell, James [University of Massachusetts, Amherst, Massachusetts, MA 01003 (United States); Lundsager, Per; Bindner, Henrik; Cronin, Tom; Noergaard, Per [Riseo National Laboratory, P.O. Box 49, Frederiksborgvej 399, 4000 Roskilde (Denmark); Ruddell, Alan [Council for the Central Laboratory of the Research Councils, Rutherford Appleton Laboratory, Energy Research Unit, Chilton, OX11 0QX Didcot (United Kingdom); Perujo, Adolfo; Douglas, Kevin [E.C. Joint Research Centre, Institute for Environment and Sustainability, 21020 Ispra VA (Italy); Rodrigues, Carlos; Joyce, Antonio [INETI, Department of Renewable Energy, Estrada do Paco de Lumiar 22, 1649-038 Lisbon (Portugal); Tselepis, Stathis [Center for Renewable Energy Sources, 19th km Marathonos Ave., 19009 Pikermi (Greece); Borg, Nico van der; Nieuwenhout, Frans [The Netherlands Energy Research Foundation, P.O. Box 1, 1755 ZG Petten (Netherlands); Wilmot, Nigel [Research Institute for Sustainable Energy, Murdoch University, South Street, 6150 Perth (Australia); Mattera, Florence [Commissariat a l' Energetie Atomicque, Groupement Energetique de Cadarache, 38054 Grenoble (France)

    2007-11-15

    Operating conditions in off-grid renewable energy systems (RES) vary significantly in different applications and locations. To describe RES and the operating conditions of their components it is useful to define categories of similar operating conditions. Categories can also be used for lifetime considerations of RES components, for making recommendations and for analysing the properties and performance of a RES and its components. Categories support system designers and an economic analysis. This paper describes the process and the results of creating RES categories of similar operating conditions for batteries. Categories are defined in such a way that batteries belonging to the same category are subjected to similar operating conditions and a similar combination of stress factors. The results provide a comprehensive overview of battery operating conditions in existing off-grid renewable energy systems. This work is part of the EU research project Benchmarking. (author)

  4. Operating conditions of batteries in off-grid renewable energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Svoboda, Vojtech; Wenzl, Heinz; Kaiser, Rudi; Jossen, Andreas; Baring-Gould, Ian; Manwell, James; Lundsager, Per; Bindner, Henrik; Cronin, Tom; Nørgård, Per; Ruddell, Alan; Perujo, Adolfo; Douglas, Kevin; Rodrigues, Carlos; Joyce, António; Tselepis, Stathis; van der Borg, Nico; Nieuwenhout, Frans; Wilmot, Nigel; Mattera, Florence; Sauer, Dirk Uwe

    2007-11-01

    Operating conditions in off-grid renewable energy systems (RES) vary significantly in different applications and locations. To describe RES and the operating conditions of their components it is useful to define categories of similar operating conditions. Categories can also be used for lifetime considerations of RES components, for making recommendations and for analysing the properties and performance of a RES and its components. Categories support system designers and an economic analysis. This paper describes the process and the results of creating RES categories of similar operating conditions for batteries. Categories are defined in such a way that batteries belonging to the same category are subjected to similar operating conditions and a similar combination of stress factors. The results provide a comprehensive overview of battery operating conditions in existing off-grid renewable energy systems. This work is part of the EU research project Benchmarking.

  5. Operating conditions of batteries in off-grid renewable energy systems

    DEFF Research Database (Denmark)

    Svoboda, V.; Wenzl, H.; Kaiser, R.

    2007-01-01

    Operating conditions in off-grid renewable energy systems (RES) vary significantly in different applications and locations. To describe RES and the operating conditions of their components it is useful to define categories of similar operating conditions. Categories can also be used for lifetime...... considerations of RES components, for making recommendations and for analysing the properties and performance of a RES and its components. Categories support system designers and an economic analysis. This paper describes the process and the results of creating RES categories of similar operating conditions...... for batteries. Categories are defined in such a way that batteries belonging to the same category are subjected to similar operating conditions and a similar combination of stress factors. The results provide a comprehensive overview of battery operating conditions in existing off-grid renewable energy systems...

  6. Scope insensitivity in contingent valuation of complex environmental amenities.

    Science.gov (United States)

    Veisten, Knut; Fredrik Hoen, Hans; Navrud, Ståle; Strand, Jon

    2004-12-01

    It has been argued that respondents in contingent valuation (CV) surveys, asked to value complex environmental amenities, will state willingness to pay (WTP) independently of the scope of the project. Such insensitivity to scope would be at odds with rational choice, and could therefore imply that CV is not a theoretically valid method for biodiversity valuation. The scope test in the present CV study was applied to endangered species preservation. Respondents were split in four sub-samples facing different scopes of endangered species preservation. The design allowed for both external and internal scope tests. Furthermore, the tests were split according to elicitation format. Of four external tests of insensitivity to scope, one was rejected, two gave mixed results, depending on either the type of test or elicitation format, and for the last one the null hypothesis could not be rejected. Of five internal tests, insensitivity to scope was rejected in three cases, one test gave mixed results, and one could not be rejected. Survey design features of the CV study, especially an unfamiliar sub-group of endangered species, could explain the apparent insensitivity to scope observed.

  7. Economic amenity values of wildlife: Six case studies in Pennsylvania

    Science.gov (United States)

    Shafer, Elwood L.; Carline, Robert; Guldin, Richard W.; Cordell, H. Ken

    1993-09-01

    The travel clost method (TCM) and contingent valuation method (CVM) were used to evaluate the economic value of six different ecotourism activities involving observation of wildlife in Pennsylvania. The six activities were: catch-and-release trout fishing; catch-and-release trout fishing with fly-fishing equipment; viewing waterfowl; watching elk; observing migration flights of raptors; and seeing live wildlife in an environmental education setting. TCM results provided significant statistical relationships between level of use and travel costs for the two types of trout fishing activities. CVM provided estimates of consumer surplus for the other four sites. The consumers' surplus value (1988 dollars) of all six activities to participants amounted to a total of more than 1.28 million annually—twice the total out-of-pocket expenditures of approximately 640,000 spent to visit the sites. The economic amenity values of the six activities compare favorably with similarly derived values in other studies for hunting, fishing, hiking, and backpacking in dispersed recreation environments and wilderness areas in western states.

  8. Field quality of the LHC dipole magnets in operating conditions

    CERN Document Server

    Bottura, L; Fartoukh, Stéphane David; Russenschuck, Stephan; Sanfilippo, S; Scandale, Walter; Schmidt, F; Todesco, Ezio; Walckiers, L; Wolf, R

    2002-01-01

    We report here the main results of the field measurements performed so far on the pre-series LHC superconducting dipoles at superfluid helium temperature. After discussing the results at injection and collision conditions, we focus on the non-linear contributions at high field, on the contribution of superconductor magnetization at injection, and on ramp rate effects. The statistics accumulated on the first magnets of the production verify the hypotheses that have been used to design the correctors scheme for the LHC. In particular high field saturation is in line with the expectations, although a small systematic deformation due to Lorentz forces affects both sextupole and decapole terms. The decay at injection and snap-back at beginning of beam acceleration require careful characterization.

  9. Upgrading of coker distillate under variable hydrotreating operating conditions

    Directory of Open Access Journals (Sweden)

    H.A. Elsayed

    2011-06-01

    Full Text Available Studies on hydrotreating coker distillates, produced from a delayed coker unit were done using a commercially available CoMo/γ-Al2O3 catalyst, on which 0.2 wt% P2O5 was added in order to improve its characteristics. The experimental studies were conducted in a fixed-bed continuous-reactor (cata-test unit at temperatures (300–400 °C and total hydrogen pressure (40–65 bar. These conditions have affected the feedstock characteristics and great reduction of sulfur, aromatics and boiling ranges. Other improvements were obtained in diesel index (DI due to hydrogenation reaction of aromatics and desulfurization of its sulfur contents.

  10. Effect of Drying Operating Conditions on Canola Oil Tocopherol Content

    Directory of Open Access Journals (Sweden)

    Daniela Laoretani

    2014-03-01

    Full Text Available The aim of this work was to evaluate two operating parameters of seed drying (temperature and initial moisture content on the tocopherol content of canola oil. The raw material was characterized by moisture, oil, protein, crude fiber and ash content. Seeds at 13.6% and 22.7% moisture content (dry basis, db were dried at temperatures in the range of 35–100 °C to a safe storage moisture of 7% db. Oil was extracted from each treated sample. The oil extracted from the samples dried at the extreme temperatures was analyzed by means of the acidity value, peroxide index and fatty acid composition, finding no significant differences among treatments or among untreated and treated samples. Tocopherol contents in the oils obtained for all the assayed temperatures were determined. Differences were found for the samples with 22.7% (db initial moisture content. Except at 35 °C, temperature affected negatively the oil tocopherol content. However, when 13.6% (db moisture seeds were processed, no significant differences were observed in the amount of this minor oil component among assays.

  11. Field study evaluation of diffuse ceiling ventilation in classroom during real operating conditions

    DEFF Research Database (Denmark)

    Kristensen, Martin Heine; Jensen, Jakob Søland; Heiselberg, Per Kvols

    2017-01-01

    Highlights •Field experimental measurements during real operating conditions. •Evaluation of pressure chamber effect. •Evaluation of displacement effect. •Evaluation of thermal comfort.......Highlights •Field experimental measurements during real operating conditions. •Evaluation of pressure chamber effect. •Evaluation of displacement effect. •Evaluation of thermal comfort....

  12. Neural Operant Conditioning as a Core Mechanism of Brain-Machine Interface Control

    Directory of Open Access Journals (Sweden)

    Yoshio Sakurai

    2016-08-01

    Full Text Available The process of changing the neuronal activity of the brain to acquire rewards in a broad sense is essential for utilizing brain-machine interfaces (BMIs, which is essentially operant conditioning of neuronal activity. Currently, this is also known as neural biofeedback, and it is often referred to as neurofeedback when human brain activity is targeted. In this review, we first illustrate biofeedback and operant conditioning, which are methodological background elements in neural operant conditioning. Then, we introduce research models of neural operant conditioning in animal experiments and demonstrate that it is possible to change the firing frequency and synchronous firing of local neuronal populations in a short time period. We also debate the possibility of the application of neural operant conditioning and its contribution to BMIs.

  13. Impact of air conditioning system operation on increasing gases emissions from automobile

    Science.gov (United States)

    Burciu, S. M.; Coman, G.

    2016-08-01

    The paper presents a study concerning the influence of air conditioning system operation on the increase of gases emissions from cars. The study focuses on urban operating regimes of the automobile, regimes when the engines have low loads or are operating at idling. Are presented graphically the variations of pollution emissions (CO, CO2, HC) depending of engine speed and the load on air conditioning system. Additionally are presented, injection duration, throttle position, the mechanical power required by the compressor of air conditioning system and the refrigerant pressure variation on the discharge path, according to the stage of charging of the air conditioning system.

  14. Condition Monitoring of Machinery in Non-Stationary Operations : Proceedings of the Second International Conference "Condition Monitoring of Machinery in Non-Stationnary Operations"

    CERN Document Server

    Bartelmus, Walter; Chaari, Fakher; Zimroz, Radoslaw; Haddar, Mohamed

    2012-01-01

    Condition monitoring of machines in non-stationary operations (CMMNO) can be seen as the major challenge for research in the field of machinery diagnostics. Condition monitoring of machines in non-stationary operations is the title of the presented book and the title of the Conference held in Hammamet - Tunisia March 26 – 28, 2012. It is the second conference under this title, first took place in Wroclaw - Poland , March 2011. The subject CMMNO comes directly from industry needs and observation of real objects. Most monitored and diagnosed objects used in industry works in non-stationary operations condition. The non-stationary operations come from fulfillment of machinery tasks, for which they are designed for. All machinery used in different kind of mines, transport systems, vehicles like: cars, buses etc, helicopters, ships and battleships and so on work in non-stationary operations. The papers included in the book are shaped by the organizing board of the conference and authors of the papers. The papers...

  15. Store operation with conditional push of a tag value to a queue

    Energy Technology Data Exchange (ETDEWEB)

    Heidelberger, Philip; Steinmacher-Burow, Burkhard

    2015-07-28

    According to one embodiment, a method for a store operation with a conditional push of a tag value to a queue is provided. The method includes configuring a queue that is accessible by an application, setting a value at an address in a memory device including a memory and a controller, receiving a request for an operation using the value at the address and performing the operation. The method also includes the controller writing a result of the operation to the address, thus changing the value at the address, the controller determining if the result of the operation meets a condition and the controller pushing a tag value to the queue based on the condition being met, where the tag value in the queue indicates to the application that the condition is met.

  16. Analysis of Fukushima unit 2 accident considering the operating conditions of RCIC system

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sung Il, E-mail: sikim@kaeri.re.kr; Park, Jong Hwa; Ha, Kwang Soon; Cho, Song-Won; Song, JinHo

    2016-03-15

    Highlights: • Fukushima unit 2 accident was analyzed using MELCOR 1.8.6. • RCIC operating conditions were assumed and best case was selected. • Effect of RCIC operating condition on accident scenario was found. - Abstract: A severe accident in Fukushima occurred on March 11, 2011 and units 1, 2 and 3 were damaged severely. A tsunami following an earthquake made the supply of electricity power stop, and the safety systems, which use AC or DC power in plants could not operate properly. It is supposed that the degree of core degradation of unit 2 is less serious than in the other plants, and it was estimated that the operation of reactor core isolation cooling (RCIC) system at the initial stage of the accident minimized the core damage through decay heat removal. Although the operating conditions of the RCIC system are not known clearly, it can be important to analyze the accident scenario of unit 2. In this study, best case of the Fukushima unit 2 accident was presented considering the operating conditions of the RCIC system. The effects of operating condition on core degradation and fission product release rate to environment were also examined. In addition, importance of torus room flooding level in the accident analysis was discussed. MELCOR 1.8.6 was used in this research, and the geometries of plant and operating conditions of safety system were obtained from TEPCO through OECD/NEA BSAF Project.

  17. Effect of RCIC Operating Conditions on the Accident Scenario in Fukushima Unit 2

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sung Il; Park, Jong Hwa; Ha, Kwang Soon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    This study was conducted by using MELCOR 1.8.6. Fukushima unit 2 accident was analyzed using MELCOR in this study, and best estimate scenario with considering RCIC operating conditions was presented. Researches on the boiling water reactor (BWR) plant with reactor core isolation cooling (RCIC) system have been conducted. Research on the RCIC operation in Fukushima unit 2 was also conducted by Sandia National Laboratory. MELCOR analysis of the Fukushima unit 2 accident was conducted in the report and energy balance in wetwell was described by considering RCIC operation. However, the effect of RCIC operation condition on the accident scenario has not been studied. The operating conditions of RCIC system affect the pressures in wetwell and drywell, and the high pressure can make leakage path of fission product from PCV to reactor building. Thus it can be directly related with the amount of fission product which released to environment. In this study, severe accident on Fukushima unit 2 was analyzed considering the operating condition of RCIC system, and best estimated scenario was presented. In addition, the effect of RCIC turbine efficiency on the accident progression was examined. Energy balance in suppression chamber was also considered with discussion on the effect of torus room flooding level. It was found that the operating condition of RCIC turbine not only affects the variation of drywell pressure but also the amount of released fission products to environment. It was also confirmed that the RCIC turbine efficiency in the accident would be less than normal operating condition.

  18. Operational-Condition-Independent Criteria Dedicated to Monitoring Wind Turbine Generators: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Yang, W.; Sheng, S.; Court, R.

    2012-08-01

    To date the existing wind turbine condition monitoring technologies and commercially available systems have not been fully accepted for improving wind turbine availability and reducing their operation and maintenance costs. One of the main reasons is that wind turbines are subject to constantly varying loads and operate at variable rotational speeds. As a consequence, the influences of turbine faults and the effects of varying load and speed are coupled together in wind turbine condition monitoring signals. So, there is an urgent need to either introduce some operational condition de-coupling procedures into the current wind turbine condition monitoring techniques or develop a new operational condition independent wind turbine condition monitoring technique to maintain high turbine availability and achieve the expected economic benefits from wind. The purpose of this paper is to develop such a technique. In the paper, three operational condition independent criteria are developed dedicated for monitoring the operation and health condition of wind turbine generators. All proposed criteria have been tested through both simulated and practical experiments. The experiments have shown that these criteria provide a solution for detecting both mechanical and electrical faults occurring in wind turbine generators.

  19. EXPERIMENTAL STUDY OF EFFECTS OF OPERATING CONDITIONS ON THE FLOW CHARACTERISTICS OF WATER HYDRAULIC THROTTLE

    Institute of Scientific and Technical Information of China (English)

    Liu Yinshui; Nie Songlin; Zhu Yuquan; He Xiaofeng; Li Zhuangyun

    2004-01-01

    Experimental investigations are made on the effects of operating conditions on the flow characteristics of throttle when tap water is used as the working media. The researched throttles include cone poppet valve, ball valve, disc valve and dumping orifice. Operating condition includes poppet lift, working media, back pressure, medium temperature, etc. Because the vapourous pressure of water is much higher than that of oil, cavitation is easier to occur in water hydraulic elements and systems, so the effects of operating conditions on the cavitation characteristics of throttle are also researched.

  20. Social capital, collective efficacy and the provision of services and amenities by municipalities.

    NARCIS (Netherlands)

    Waverijn, G.; Groenewegen, P.P.; Klerk, M. de

    2017-01-01

    Differential provision of local services and amenities has been proposed as a mechanism behind the relationship between social capital and health. The aim of this study was to investigate whether social capital and collective efficacy are related to the provision of social support services and amen

  1. [Amenable mortality as indicator of effectiveness of health care services in Spain before and after transferences].

    Science.gov (United States)

    Barrasa Villar, J I; Castán Ruiz, S; Estupiñán Romero, F R; Valderrama Rodríguez, M; Moliner Lahoz, F J

    2013-01-01

    To describe the evolution of amenable mortality (MRASS) in Spain and to evaluate differences in trend patterns before and after health care services were transferred to local authorities. MRASS was defined from a list of causes of death used in other studies. We analyzed the change in sex-age-standardized death rates of MRASS in two periods: 1999-2001 and 2006-2008, just before, and five years after, the health care transfers were completed. MRASS represented 24% of deaths in persons from 0 to 74 years old. MRASS has seen a reduction (19.4%) between the two periods over and above other causes of mortality (14.5%). The group of causes of mortality which showed most reduction: ischemic heart disease (28%), other vascular disease (27%), surgical conditions and surgical-medical errors (26%), and diabetes (22.5%). Although there were differences between the districts, health care transfers have not created significant variations in MRASS. Navarra and Madrid showed lower rates of MRASS, and the Canary Islands, Asturias, Andalusia, Ceuta and Melilla had higher rates. The Balearic Islands showed the greatest reduction in MRASS. MRASS constitutes an important proportion of trends of mortality in persons between 0-74 years. It has declined in all districts. Even though there were large differences between districts, there does not appear to be any direct influence due to health care transfer in amenable mortality trends. In spite of limitations, MRASS is an indicator to be considered when monitoring and detecting weaknesses in the effectiveness of health care systems. Copyright © 2012 SECA. Published by Elsevier Espana. All rights reserved.

  2. The characteristics of the combustion process occurring under real operating conditions of traction

    Science.gov (United States)

    Longwic, R.; Sander, P.

    2016-09-01

    The authors deal with the issues of the Diesel engine under dynamic conditions. The conditions of the dynamic operation of the engine have most frequently been mapped by the method of free acceleration of the engine caused by the change of the position of the fuel dose lever. The article presents the results of indication of the traction Diesel engine under real operating conditions. This allows for the use of a mobile system to indicate the AVL engine built in the vehicle in research. We analysed a number of thermodynamic parameters of the combustion process in various dynamic states, typical for the process of actual operation of the engine, such as working in start-up conditions and immediately after, working in conditions of acceleration and coasting. Formulated conclusions significantly expand the area of knowledge concerning the functioning of the internal combustion engine in dynamic conditions.

  3. Operational-Condition-Independent Criteria Dedicated to Monitoring Wind Turbine Generators

    Directory of Open Access Journals (Sweden)

    Richard Court

    2013-01-01

    Full Text Available Condition monitoring is beneficial to the wind industry for both onshore and offshore plants. However, due to the variations in operational conditions, its potential has not been fully explored. There is a need to develop an operational-condition-independent condition monitoring technique, which has motivated the research presented here. In this paper, three operational-condition-independent criteria are developed. The criteria accomplish the condition monitoring by analyzing the wind turbine electrical signals in the time domain. Therefore, they are simple to calculate and ideal for online use. All proposed criteria were tested through both simulated and practical experiments. The experiments have shown that these criteria not only provide a solution for detecting both mechanical and electrical faults that occur in wind turbine generators, but provide a potential tool for diagnosing generator winding faults.

  4. Matrix multiplication operations with data pre-conditioning in a high performance computing architecture

    Science.gov (United States)

    Eichenberger, Alexandre E; Gschwind, Michael K; Gunnels, John A

    2013-11-05

    Mechanisms for performing matrix multiplication operations with data pre-conditioning in a high performance computing architecture are provided. A vector load operation is performed to load a first vector operand of the matrix multiplication operation to a first target vector register. A load and splat operation is performed to load an element of a second vector operand and replicating the element to each of a plurality of elements of a second target vector register. A multiply add operation is performed on elements of the first target vector register and elements of the second target vector register to generate a partial product of the matrix multiplication operation. The partial product of the matrix multiplication operation is accumulated with other partial products of the matrix multiplication operation.

  5. A method for aggregating external operating conditions in multi-generation system optimization models

    DEFF Research Database (Denmark)

    Lythcke-Jørgensen, Christoffer Ernst; Münster, Marie; Ensinas, Adriano Viana

    2016-01-01

    This paper presents a novel, simple method for reducing external operating condition datasets to be used in multi-generation system optimization models. The method, called the Characteristic Operating Pattern (CHOP) method, is a visually-based aggregation method that clusters reference data based...... on parameter values rather than time of occurrence, thereby preserving important information on short-term relations between the relevant operating parameters. This is opposed to commonly used methods where data are averaged over chronological periods (months or years), and extreme conditions are hidden...... in the averaged values. The CHOP method is tested in a case study where the operation of a fictive Danish combined heat and power plant is optimized over a historical 5-year period. The optimization model is solved using the full external operating condition dataset, a reduced dataset obtained using the CHOP...

  6. Relative Effectiveness of Operant Conditioning and Play Therapy in Childhood Schizophrenia

    Science.gov (United States)

    Ney, Philip G.; And Others

    1971-01-01

    An experimental study designed to examine the relative effectiveness of operant conditioning and play therapy in improving the communication and social functioning of psychotic children was presented and discussed. (Author)

  7. THE MINIMAL PROPERTY OF THE CONDITION NUMBER OF INVERTIBLE LINEAR BOUNDED OPERATORS IN BANACH SPACES

    Institute of Scientific and Technical Information of China (English)

    陈果良; 魏木生

    2002-01-01

    In this paper we show that in error estimates, the condition number κ(T) of any invertible linear bounded operator T in Banach spaces is minimal. We also extend the Hahn-Banach theorem and other related results.

  8. Optimization of recirculating laminar air flow in operating room air conditioning systems

    Directory of Open Access Journals (Sweden)

    Enver Yalcin

    2016-04-01

    Full Text Available The laminar flow air-conditioning system with 100% fresh air is used in almost all operating rooms without discrimination in Turkey. The laminar flow device which is working with 100% fresh air should be absolutely used in Type 1A operating rooms. However, there is not mandatory to use of 100% fresh air for Type 1B defined as places performed simpler operation. Compared with recirculating laminar flow, energy needs of the laminar flow with 100 % fresh air has been emerged about 40% more than re-circulated air flow. Therefore, when a recirculating laminar flow device is operated instead of laminar flow system with 100% fresh air in the Type 1B operating room, annual energy consumption will be reduced. In this study, in an operating room with recirculating laminar flow, optimal conditions have been investigated in order to obtain laminar flow form by analyzing velocity distributions at various supply velocities by using computational fluid dynamics method (CFD.

  9. Effect of automobile operating condition on the subjective equivalence of steering wheel vibration and sound

    OpenAIRE

    2007-01-01

    For the manufacturers of automobiles, automobile components and fuels, subjective equivalence relationships between vibration and sound can be used as a reference against which to plot the results from simulations or tests of specific operational conditions. The research described here was performed to define curves of subjective equivalence between steering wheel rotational vibration and sound using stimuli from different automobile operating conditions. The steering wheel acceleration stimu...

  10. Zeros and poles of quantum current operators and the condition of quantum integrability

    CERN Document Server

    Ding, J; Ding, Jintai; Miwa, Tetsuji

    1996-01-01

    For the current realization of the affine quantum groups, a simple comultiplication for the quantum current operators was given by Drinfeld. With this comultiplication, we study the zeros and poles of the quantum current operators and present a condition of integrability on the quantum current of $U_q\\left(\\hat{\\frak sl}(2)\\right)$, which is a deformation of the corresponding condition for $\\hat{\\frak sl}(2)$.

  11. Control of hybrid AC/DC microgrid under islanding operational conditions

    DEFF Research Database (Denmark)

    Ding, G.; Gao, F.; Zhang, S.

    2014-01-01

    This paper presents control methods for hybrid AC/DC microgrid under islanding operation condition. The control schemes for AC sub-microgrid and DC sub-microgrid are investigated according to the power sharing requirement and operational reliability. In addition, the key control schemes......, the whole hybrid AC/DC microgrid can manage the power flow transferred between sub-microgrids for improving on the operational quality and efficiency....

  12. A Paradigm for Operant Conditioning in Blow Flies ("Phormia Terrae Novae" Robineau-Desvoidy, 1830)

    Science.gov (United States)

    Sokolowski, Michel B. C.; Disma, Gerald; Abramson, Charles I.

    2010-01-01

    An operant conditioning situation for the blow fly ("Protophormia terrae novae") is described. Individual flies are trained to enter and reenter a hole as the operant response. Only a few sessions of contingent reinforcement are required to increase response rates. When the response is no longer followed by food, the rate of entering the hole…

  13. Deficiency indices of a differential operator satisfying certain matching interface conditions

    Directory of Open Access Journals (Sweden)

    Pallav Kumar Baruah

    2005-03-01

    Full Text Available A pair of differential operators with matching interface conditions appears in many physical applications such as: oceanography, the study of step index fiber in optical fiber communication, and one dimensional scattering in quantum theory. Here we initiate the study the deficiency index theory of such operators which precedes the study of the spectral theory.

  14. Long term performance of gas-insulated switchgear operating under tropical conditions

    NARCIS (Netherlands)

    Pharmatrisanti, A.

    2012-01-01

    For the past two decades, electricity utilities have struggled to provide high quality electrical power to their customers while keeping on spending effectively the expenses for operating and maintaining the power system. Unfortunately, under tropical conditions, operation circumstances affect the e

  15. Non-trapping condition for semiclassical Schr dinger operators with matrix-valued potentials.

    CERN Document Server

    Jecko, T

    2004-01-01

    We consider semiclassical Schr dinger operators with matrix-valued, long-range, smooth potential, for which different eigenvalues may cross on a codimension one submanifold. We denote by h the semiclassical parameter and we consider energies above the bottom of the essential spectrum. Under some invariance condition on the matricial structure of the potential near the eigenvalues crossing and some structure condition at infinity, we prove that the boundary values of the resolvent at energy lambda, as bounded operators on suitable weighted spaces, are O(1/h) if and only if lambda is a non-trapping energy for all the Hamilton flows generated by the eigenvalues of the operator's symbol.

  16. Pre-Swirl Stator and Propeller Design for Varying Operating Conditions

    DEFF Research Database (Denmark)

    Saettone, Simone; Regener, Pelle Bo; Andersen, Poul

    2016-01-01

    blades ahead of the propeller.This paper describes the hydrodynamic design of apre-swirl stator with radially variable pitch, paired with aconventional propeller. The aim is to achieve the highest possible effciency in various operating conditions, and to avoid effciency penalties in off-design operation.......To investigate the propeller and stator designs and configurations in different operating conditions, the computationally inexpensive vortex-lattice method is used a sa first step to optimize the geometry in an initial parameter study. Then the flow over hull, stator and propelleris simulated in a CFD...

  17. Feeding Behavior of Aplysia: A Model System for Comparing Cellular Mechanisms of Classical and Operant Conditioning

    Science.gov (United States)

    Baxter, Douglas A.; Byrne, John H.

    2006-01-01

    Feeding behavior of Aplysia provides an excellent model system for analyzing and comparing mechanisms underlying appetitive classical conditioning and reward operant conditioning. Behavioral protocols have been developed for both forms of associative learning, both of which increase the occurrence of biting following training. Because the neural…

  18. Contriving Transitive Conditioned Establishing Operations to Establish Derived Manding Skills in Adults with Severe Developmental Disabilities

    Science.gov (United States)

    Rosales, Rocio; Rehfeldt, Ruth Anne

    2007-01-01

    The purpose of this study was to demonstrate derived manding skills in 2 adults with severe developmental disabilities and language deficits by contriving transitive conditioned establishing operations. Specifically, we evaluated whether a history of reinforced conditional discrimination learning would ultimately result in a derived mand…

  19. Design of optimal operating conditions of simulated moving bed adsorptive separation units

    Energy Technology Data Exchange (ETDEWEB)

    Storti, G. (Univ. degli Studi di Padova (Italy)); Baciocchi, R.; Mazzotti, M.; Morbidelli, M. (Politecnico di Milano (Italy). Dipt. di Chimica Fisica Applicata)

    1995-01-01

    The design of the optimal operating conditions for simulated moving bed (SMB) adsorptive separation units is considered. A procedure for the a priori selection of the operating conditions to achieve an assigned separation requirement is developed in the frame of equilibrium theory for the equivalent four section countercurrent unit, using a model where the adsorption equilibria are described through the constant selectivity stoichiometric model, while both mass transfer resistance and axial dispersion are neglected. The space of the operating parameters, i.e. the mass flow rate ratios m[sub j], is divided in regions with different separation regimes. Curves at constant outlets purity and recovery are drawn in the (m[sub 2],m[sub 3]) plane. The introduction of three performance parameters, desorbent requirement, adsorbent requirement, and productivity, allows the development of a procedure for the design of optimal operating conditions. This procedure is completed, accounting for the effect of the switching time on the separation performances, with a detailed model of the SMB unit, considering both axial dispersion and mass transfer resistance. This result constitutes a useful tool for determining the range of operating conditions to achieve an assigned separation requirement and then for selecting the optimal operating condition within this range.

  20. Analysis and discretization of the volume penalized Laplace operator with Neumann boundary conditions

    CERN Document Server

    Kolomenskiy, Dmitry; Schneider, Kai

    2014-01-01

    We study the properties of an approximation of the Laplace operator with Neumann boundary conditions using volume penalization. For the one-dimensional Poisson equation we compute explicitly the exact solution of the penalized equation and quantify the penalization error. Numerical simulations using finite differences allow then to assess the discretisation and penalization errors. The eigenvalue problem of the penalized Laplace operator with Neumann boundary conditions is also studied. As examples in two space dimensions, we consider a Poisson equation with Neumann boundary conditions in rectangular and circular domains.

  1. Many-body position operator in lattice fermionic systems with periodic boundary conditions

    Energy Technology Data Exchange (ETDEWEB)

    Hetenyi, Balazs [Institut fuer Theoretische Physik, Technische Universitaet Graz, Petersgasse 16, A-8010 Graz (Austria); Mathematisches Institut, Fakultaet fuer Mathematik, Informatik und Statistik, Ludwig Maximilians Universitaet, Theresienstrasse 39, Muenchen 80333 (Germany)], E-mail: hetenyi@itp.tugraz.at

    2009-10-16

    A total position operator X in the position representation is derived for lattice fermionic systems with periodic boundary conditions. The operator is shown to be Hermitian, the generator of translations in momentum space, and its time derivative is shown to correspond to the total current operator in a periodic system. The operator is such that its moments can be calculated up to any order. To demonstrate its utility finite size scaling is applied to the Brinkman-Rice transition as well as to metallic and insulating Gutzwiller wavefunctions. (fast track communication)

  2. Fluid dynamic characterization of operating conditions for continuous flow blood pumps.

    Science.gov (United States)

    Wu, Z J; Antaki, J F; Burgreen, G W; Butler, K C; Thomas, D C; Griffith, B P

    1999-01-01

    As continuous flow pumps become more prominent as long-term ventricular assist devices, the wide range of conditions under which they must be operated has become evident. Designed to operate at a single, best-efficiency, operating point, continuous flow pumps are required to perform at off-design conditions quite frequently. The present study investigated the internal fluid dynamics within two representative rotary fluid pumps to characterize the quality of the flow field over a full range of operating conditions. A Nimbus/UoP axial flow blood pump and a small centrifugal pump were used as the study models. Full field visualization of flow features in the two pumps was conducted using a laser based fluorescent particle imaging technique. Experiments were performed under steady flow conditions. Flow patterns at inlet and outlet sections were visualized over a series of operating points. Flow features specific to each pump design were observed to exist under all operating conditions. At off-design conditions, an annular region of reverse flow was commonly observed within the inlet of the axial pump, while a small annulus of backflow in the inlet duct and a strong disturbed flow at the outlet tongue were observed for the centrifugal pump. These observations were correlated to a critical nondimensional flow coefficient. The creation of a "map" of flow behavior provides an additional, important criterion for determining favorable operating speed for rotary blood pumps. Many unfavorable flow features may be avoided by maintaining the flow coefficient above a characteristic critical coefficient for a particular pump, whereas the intrinsic deleterious flow features can only be minimized by design improvement. Broadening the operating range by raising the band between the critical flow coefficient and the designed flow coefficient, is also a worthy goal for design improvement.

  3. Determination of Initial Conditions for the Safety Analysis by Random Sampling of Operating Parameters

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Hae-Yong; Park, Moon-Ghu [Sejong University, Seoul (Korea, Republic of)

    2015-05-15

    In most existing evaluation methodologies, which follow a conservative approach, the most conservative initial conditions are searched for each transient scenario through tremendous assessment for wide operating windows or limiting conditions for operation (LCO) allowed by the operating guidelines. In this procedure, a user effect could be involved and a remarkable time and human resources are consumed. In the present study, we investigated a more effective statistical method for the selection of the most conservative initial condition by the use of random sampling of operating parameters affecting the initial conditions. A method for the determination of initial conditions based on random sampling of plant design parameters is proposed. This method is expected to be applied for the selection of the most conservative initial plant conditions in the safety analysis using a conservative evaluation methodology. In the method, it is suggested that the initial conditions of reactor coolant flow rate, pressurizer level, pressurizer pressure, and SG level are adjusted by controlling the pump rated flow, setpoints of PLCS, PPCS, and FWCS, respectively. The proposed technique is expected to contribute to eliminate the human factors introduced in the conventional safety analysis procedure and also to reduce the human resources invested in the safety evaluation of nuclear power plants.

  4. TRUNK WITH BRANCHES PUBLIC TRANSPORT LINE SCHEDULLING UNDER CONDITION OF UNIFORM HEADWAY OPERATION

    Directory of Open Access Journals (Sweden)

    Nikola Krstanoski

    2015-12-01

    Full Text Available Planning of public transport network for good spatial coverage may lead to an operation of radial or diametrical public transport lines that branch at one or both ends of the line. This trunk with branches operation means that all vehicles on the line serve the main - trunk section, usually covering the central area of the city, and then split in two or more branches in the peripheral areas, in order to offer better spatial service. The scheduling of this type of operation is not an easy task since only certain patterns of headways and therefore passenger demands can be met, if efficient operation under the condition of uniform headways on all sections on the line is required. In this article the author analyzes the key variables that define the uniform headway operation and establishes their relationships, thus providing answer to the question what headway patterns are feasible and if they could be acceptable for real life operation.

  5. Performance of diagonal control structures at different operating conditions for polymer electrolyte membrane fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Serra, Maria; Husar, Attila; Feroldi, Diego; Riera, Jordi [Institut de Robotica i Informatica Industrial, Universitat Politecnica de Catalunya, Consejo Superior de Investigaciones Cientificas, C. Llorens i Artigas 4, 08028 Barcelona (Spain)

    2006-08-25

    This work is focused on the selection of operating conditions in polymer electrolyte membrane fuel cells. It analyses efficiency and controllability aspects, which change from one operating point to another. Specifically, several operating points that deliver the same amount of net power are compared, and the comparison is done at different net power levels. The study is based on a complex non-linear model, which has been linearised at the selected operating points. Different linear analysis tools are applied to the linear models and results show important controllability differences between operating points. The performance of diagonal control structures with PI controllers at different operating points is also studied. A method for the tuning of the controllers is proposed and applied. The behaviour of the controlled system is simulated with the non-linear model. Conclusions indicate a possible trade-off between controllability and optimisation of hydrogen consumption. (author)

  6. Detection and classification of alarm threshold violations in condition monitoring systems working in highly varying operational conditions

    Science.gov (United States)

    Strączkiewicz, M.; Barszcz, T.; Jabłoński, A.

    2015-07-01

    All commonly used condition monitoring systems (CMS) enable defining alarm thresholds that enhance efficient surveillance and maintenance of dynamic state of machinery. The thresholds are imposed on the measured values such as vibration-based indicators, temperature, pressure, etc. For complex machinery such as wind turbine (WT) the total number of thresholds might be counted in hundreds multiplied by the number of operational states. All the parameters vary not only due to possible machinery malfunctions, but also due to changes in operating conditions and these changes are typically much stronger than the former ones. Very often, such a behavior may lead to hundreds of false alarms. Therefore, authors propose a novel approach based on parameterized description of the threshold violation. For this purpose the novelty and severity factors are introduced. The first parameter refers to the time of violation occurrence while the second one describes the impact of the indicator-increase to the entire machine. Such approach increases reliability of the CMS by providing the operator with the most useful information of the system events. The idea of the procedure is presented on a simulated data similar to those from a wind turbine.

  7. What matters more for the decision to move: jobs versus amenities

    DEFF Research Database (Denmark)

    Niedomysl, Thomas; Hansen, Høgni Kalsø

    2010-01-01

    the relative importance of jobs versus amenities for the decision to migrate, as perceived by the migrants themselves. The paper thereby adds important insights to the existing literature that has hitherto mainly focused on analysing the extent to which aggregate migration flows correlate with employment......-related or amenity-related factors. The results show that jobs are considerably more important for the decision to move among highly educated migrants compared with migrants with lower education....

  8. Social inequalities in causes of death amenable to health care in Norway

    Directory of Open Access Journals (Sweden)

    Camilla Hem

    2007-01-01

    Full Text Available Objective: Investigate if there are educational inequalities in causes of death considered amenable to health care in Norway and compare this with non-amenable causes. Methods: The study used the concept of “amenable mortality”, which here includes 34 specific causes of death. A linked data file, with information from the Norwegian Causes of Death Registry and the Educational Registry was analyzed. The study population included the whole Norwegian population in two age groups of interest (25-49 and 50-74 years. Information on deaths was from the period 1990-2001. Education was recorded in 1990 and it was grouped in four categories as: basic, lower secondary, higher secondary and higher. In the study men and women were analysed seperately. The analysis was conducted for all amenable causes pooled with and without ischemic heart disease. A Cox proportional hazard regression model was fitted to estimate hazard rate ratios. Results: The study showed educational differences in mortality from causes of death considered amenable to health care, in both age groups and sexes. This was seen both when including and excluding ischemic heart disease. The effect sizes were comparable for amenable and non-amenable causes in both age groups and sexes. Conclusions: This study revealed systematic higher risk of death in lower educational groups in causes of death considered amenable to health care. This indicates potential weaknesses in equitable provision of health care for the Norwegian population. Additional research is needed to identify domains within the health care system of particular concern.

  9. Significance of Operating Environment in Condition Monitoring of Large Civil Structures

    Directory of Open Access Journals (Sweden)

    Sreenivas Alampalli

    1999-01-01

    Full Text Available Success of remote long-term condition monitoring of large civil structures and developing calibrated analytical models for damage detection, depend significantly on establishing accurate baseline signatures and their sensitivity. Most studies reported in the literature concentrated on the effect of structural damage on modal parameters without emphasis on reliability of modal parameters. Thus, a field bridge structure was studied for the significance of operating conditions in relation to baseline signatures. Results indicate that in practice, civil structures should be monitored for at least one full cycle of in-service environmental changes before establishing baselines for condition monitoring or calibrating finite-element models. Boundary conditions deserve special attention.

  10. Classifier-ensemble incremental-learning procedure for nuclear transient identification at different operational conditions

    Energy Technology Data Exchange (ETDEWEB)

    Baraldi, Piero, E-mail: piero.baraldi@polimi.i [Dipartimento di Energia - Sezione Ingegneria Nucleare, Politecnico di Milano, via Ponzio 34/3, 20133 Milano (Italy); Razavi-Far, Roozbeh [Dipartimento di Energia - Sezione Ingegneria Nucleare, Politecnico di Milano, via Ponzio 34/3, 20133 Milano (Italy); Zio, Enrico [Dipartimento di Energia - Sezione Ingegneria Nucleare, Politecnico di Milano, via Ponzio 34/3, 20133 Milano (Italy); Ecole Centrale Paris-Supelec, Paris (France)

    2011-04-15

    An important requirement for the practical implementation of empirical diagnostic systems is the capability of classifying transients in all plant operational conditions. The present paper proposes an approach based on an ensemble of classifiers for incrementally learning transients under different operational conditions. New classifiers are added to the ensemble where transients occurring in new operational conditions are not satisfactorily classified. The construction of the ensemble is made by bagging; the base classifier is a supervised Fuzzy C Means (FCM) classifier whose outcomes are combined by majority voting. The incremental learning procedure is applied to the identification of simulated transients in the feedwater system of a Boiling Water Reactor (BWR) under different reactor power levels.

  11. Mapping of optimum operating condition for LiBr–water refrigeration cycles

    Indian Academy of Sciences (India)

    NILESH A MALI; SUNIL S BHAGWAT

    2017-02-01

    In this work, optimum operating condition maps are generated covering wide ranges of refrigeration and sink temperatures for single- and double-effect LiBr–water vapour absorption refrigeration cycle. These optimum condition maps will be useful to choose optimum operating conditions while designing LiBr–water cycle for desired applications. Methodology for generating such maps is discussed in detail, which can also beused for other absorption refrigeration cycles with various working fluids. Three configurations of LiBr–water absorption refrigeration cycles, single effect, double-effect series flow and double-effect parallel flow, are analysed with the most accurate thermodynamic property correlation available in the literature. Sensitivity of cycle performance to various operating variables such as generator, absorber and condenser temperatures is determined. Second law analysis shows that when a higher temperature heat source is available, double-effect cycles are more effective over single effect as they have higher coefficient of performance.

  12. Assessment of biogas production from MBT waste under different operating conditions

    DEFF Research Database (Denmark)

    Pantini, Sara; Verginelli, Jason; Lombardi, Francesco;

    2015-01-01

    In this work, the influence of different operating conditions on the biogas production from mechanically-. biologically treated (MBT) wastes is investigated. Specifically, different lab-scale anaerobic tests varying the water content (26-43% w/w up to 75% w/w), the temperature (from 20 to 25......, the obtained results highlighted that the operative conditions can drastically affect the gas production from MET wastes. This suggests that particular caution should be paid when using the results of lab-scale tests for the evaluation of long-term behaviour expected in the field where the boundary conditions...... change continuously and vary significantly depending on the climate, the landfill operative management strategies in place (e.g. leachate recirculation, waste disposal methods), the hydraulic characteristics of disposed waste, the presence and type of temporary and final cover systems. (C) 2015 Elsevier...

  13. Identifying the microbial communities and operational conditions for optimized wastewater treatment in microbial fuel cells.

    Science.gov (United States)

    Ishii, Shun'ichi; Suzuki, Shino; Norden-Krichmar, Trina M; Wu, Angela; Yamanaka, Yuko; Nealson, Kenneth H; Bretschger, Orianna

    2013-12-01

    Microbial fuel cells (MFCs) are devices that exploit microorganisms as "biocatalysts" to recover energy from organic matter in the form of electricity. MFCs have been explored as possible energy neutral wastewater treatment systems; however, fundamental knowledge is still required about how MFC-associated microbial communities are affected by different operational conditions and can be optimized for accelerated wastewater treatment rates. In this study, we explored how electricity-generating microbial biofilms were established at MFC anodes and responded to three different operational conditions during wastewater treatment: 1) MFC operation using a 750 Ω external resistor (0.3 mA current production); 2) set-potential (SP) operation with the anode electrode potentiostatically controlled to +100 mV vs SHE (4.0 mA current production); and 3) open circuit (OC) operation (zero current generation). For all reactors, primary clarifier effluent collected from a municipal wastewater plant was used as the sole carbon and microbial source. Batch operation demonstrated nearly complete organic matter consumption after a residence time of 8-12 days for the MFC condition, 4-6 days for the SP condition, and 15-20 days for the OC condition. These results indicate that higher current generation accelerates organic matter degradation during MFC wastewater treatment. The microbial community analysis was conducted for the three reactors using 16S rRNA gene sequencing. Although the inoculated wastewater was dominated by members of Epsilonproteobacteria, Gammaproteobacteria, and Bacteroidetes species, the electricity-generating biofilms in MFC and SP reactors were dominated by Deltaproteobacteria and Bacteroidetes. Within Deltaproteobacteria, phylotypes classified to family Desulfobulbaceae and Geobacteraceae increased significantly under the SP condition with higher current generation; however those phylotypes were not found in the OC reactor. These analyses suggest that species

  14. Operational Meanings of Orders of Observables Defined through Quantum Set Theories with Different Conditionals

    Directory of Open Access Journals (Sweden)

    Masanao Ozawa

    2017-01-01

    Full Text Available In quantum logic there is well-known arbitrariness in choosing a binary operation for conditional. Currently, we have at least three candidates, called the Sasaki conditional, the contrapositive Sasaki conditional, and the relevance conditional. A fundamental problem is to show how the form of the conditional follows from an analysis of operational concepts in quantum theory. Here, we attempt such an analysis through quantum set theory (QST. In this paper, we develop quantum set theory based on quantum logics with those three conditionals, each of which defines different quantum logical truth value assignment. We show that those three models satisfy the transfer principle of the same form to determine the quantum logical truth values of theorems of the ZFC set theory. We also show that the reals in the model and the truth values of their equality are the same for those models. Interestingly, however, the order relation between quantum reals significantly depends on the underlying conditionals. We characterize the operational meanings of those order relations in terms of joint probability obtained by the successive projective measurements of arbitrary two observables. Those characterizations clearly show their individual features and will play a fundamental role in future applications to quantum physics.

  15. Altitude Performance of Modified J71 Afterburner with Revised Engine Operating Conditions

    Science.gov (United States)

    Useller, James W.; Russey, Robert E.

    1955-01-01

    An investigation was conducted in an altitude test chamber at the NACA Lewis laboratory to determine the effect of a revision of the rated engine operating conditions and modifications to the afterburner fue1 system, flameholder, and shell cooling on the augmented performance of the J71-A-2 (x-29) turbo jet engine operating at altitude . The afterburner modifications were made by the manufacturer to improve the endurance at sea-level, high-pressure conditions and to reduce the afterburner shell temperatures. The engine operating conditions of rated rotational speed and turbine-outlet gas temperature were increased. Data were obtained at conditions simulating flight at a Mach number of 0.9 and at altitudes from 40,000 to 60,000 feet. The afterburner modifications caused a reduction in afterburner combustion efficiency. The increase in rated engine speed and turbine-outlet temperature coupled with the afterburner modifications resulted in the over-all thrust of the engine and afterburner being unchanged at a given afterburner equivalence ratio, while the specific fuel consumption was increased slightly. A moderate shift in the range of equivalence ratios over which the afterburner would operate was encountered, but the maximum operable altitude remained unaltered. The afterburner-shell temperatures were also slightly reduced because of the modifications to the afterburner.

  16. Operational condition of direct single-mode-fiber coupled FSO terminal under strong atmospheric turbulence

    Science.gov (United States)

    Arimoto, Yoshinori

    2011-03-01

    This paper discusses the operational condition for direct single-mode-fiber-coupling FSO terminals under the various adverse weather conditions, such as strong atmospheric turbulences and rain falls. A good correlation between the scintillation index of the intensities of beacon receiving power and the signal fading depth has been observed, which allows us to predict the signal link quality based on the beacon scintillation index provided by the classical scintillation theory and concludes that the scintillation index for the beacon beam should be less than 0.1. This paper also reports the effect of performance enhancements provided by the new adaptive controller for the stable and robust terminal operation.

  17. Towards energy efficient operation of Heating, Ventilation and Air Conditioning systems via advanced supervisory control design

    Science.gov (United States)

    Oswiecinska, A.; Hibbs, J.; Zajic, I.; Burnham, K. J.

    2015-11-01

    This paper presents conceptual control solution for reliable and energy efficient operation of heating, ventilation and air conditioning (HVAC) systems used in large volume building applications, e.g. warehouse facilities or exhibition centres. Advanced two-level scalable control solution, designed to extend capabilities of the existing low-level control strategies via remote internet connection, is presented. The high-level, supervisory controller is based on Model Predictive Control (MPC) architecture, which is the state-of-the-art for indoor climate control systems. The innovative approach benefits from using passive heating and cooling control strategies for reducing the HVAC system operational costs, while ensuring that required environmental conditions are met.

  18. Golden Indica and Japonica rice lines amenable to deregulation.

    Science.gov (United States)

    Hoa, Tran Thi Cuc; Al-Babili, Salim; Schaub, Patrick; Potrykus, Ingo; Beyer, Peter

    2003-09-01

    As an important step toward free access and, thus, impact of GoldenRice, a freedom-to-operate situation has been achieved for developing countries for the technology involved. Specifically, to carry the invention beyond its initial "proof-of-concept" status in a Japonica rice (Oryza sativa) cultivar, we report here on two transformed elite Indica varieties (IR64 and MTL250) plus one Japonica variety Taipei 309. Indica varieties are predominantly consumed in the areas with vitamin A deficiency. To conform with regulatory constraints, we changed the vector backbone, investigated the absence of beyond-border transfer, and relied on Agrobacterium tumefaciens-mediated transformation to obtain defined integration patterns. To avoid an antibiotic selection system, we now rely exclusively on phosphomannose isomerase as the selectable marker. Single integrations were given a preference to minimize potential epigenetic effects in subsequent generations. These novel lines, now in the T(3) generation, are highly valuable because they are expected to more readily receive approval for follow-up studies such as nutritional and risk assessments and for breeding approaches leading to locally adapted variety development.

  19. Methodology for selection of attributes and operating conditions for SVM-Based fault locator's

    Directory of Open Access Journals (Sweden)

    Debbie Johan Arredondo Arteaga

    2017-01-01

    Full Text Available Context: Energy distribution companies must employ strategies to meet their timely and high quality service, and fault-locating techniques represent and agile alternative for restoring the electric service in the power distribution due to the size of distribution services (generally large and the usual interruptions in the service. However, these techniques are not robust enough and present some limitations in both computational cost and the mathematical description of the models they use. Method: This paper performs an analysis based on a Support Vector Machine for the evaluation of the proper conditions to adjust and validate a fault locator for distribution systems; so that it is possible to determine the minimum number of operating conditions that allow to achieve a good performance with a low computational effort. Results: We tested the proposed methodology in a prototypical distribution circuit, located in a rural area of Colombia. This circuit has a voltage of 34.5 KV and is subdivided in 20 zones. Additionally, the characteristics of the circuit allowed us to obtain a database of 630.000 records of single-phase faults and different operating conditions. As a result, we could determine that the locator showed a performance above 98% with 200 suitable selected operating conditions. Conclusions: It is possible to improve the performance of fault locators based on Support Vector Machine. Specifically, these improvements are achieved by properly selecting optimal operating conditions and attributes, since they directly affect the performance in terms of efficiency and the computational cost.

  20. 4th International Conference on Condition Monitoring of Machinery in Non-Stationary Operations

    CERN Document Server

    Zimroz, Radoslaw; Bartelmus, Walter; Haddar, Mohamed

    2016-01-01

    The book provides readers with a snapshot of recent research and technological trends in the field of condition monitoring of machinery working under a broad range of operating conditions. Each chapter, accepted after a rigorous peer-review process, reports on an original piece of work presented and discussed at the 4th International Conference on Condition Monitoring of Machinery in Non-stationary Operations, CMMNO 2014, held on December 15-16, 2014, in Lyon, France. The contributions have been grouped into three different sections according to the main subfield (signal processing, data mining, or condition monitoring techniques) they are related to. The book includes both theoretical developments as well as a number of industrial case studies, in different areas including, but not limited to: noise and vibration; vibro-acoustic diagnosis; signal processing techniques; diagnostic data analysis; instantaneous speed identification; monitoring and diagnostic systems; and dynamic and fault modeling. This book no...

  1. 20 CFR 662.430 - Under what conditions may One-Stop operators designated to operate in a One-Stop delivery system...

    Science.gov (United States)

    2010-04-01

    ... designated to operate in a One-Stop delivery system established prior to the enactment of WIA be designated... DESCRIPTION OF THE ONE-STOP SYSTEM UNDER TITLE I OF THE WORKFORCE INVESTMENT ACT One-Stop Operators § 662.430 Under what conditions may One-Stop operators designated to operate in a One-Stop delivery system...

  2. A hydrodynamic optimization design methodology for a ship bulbous bow under multiple operating conditions

    OpenAIRE

    Yu Lu; Xin Chang; An-kang Hu

    2016-01-01

    The main objective of this article is to describe an innovative methodology for the hydrodynamic optimization of a ship bulbous bow which considers multiple operating conditions. The proposed method is more practical and effective than the traditional optimization process, which is only based on contractually specified design condition. Parametric form approaches are adopted by employing an F-spline curve in order to generate variants of the hull bulbous bow forms using form design parameters...

  3. New oil condition monitoring system, Wearsens® enables continuous, online detection of critical operating conditions and wear damage

    Directory of Open Access Journals (Sweden)

    Manfred Mauntz

    2015-12-01

    Full Text Available A new oil sensor system is presented for the continuous, online measurement of the wear in turbines, industrial gears, generators, hydraulic systems and transformers. Detection of change is much earlier than existing technologies such as particle counting, vibration measurement or recording temperature. Thus targeted, corrective procedures and/or maintenance can be carried out before actual damage occurs. Efficient machine utilization, accurately timed preventive maintenance, increased service life and a reduction of downtime can all be achieved. The presented sensor system effectively controls the proper operation conditions of bearings and cogwheels in gears. The online diagnostics system measures components of the specific complex impedance of oils. For instance, metal abrasion due to wear debris, broken oil molecules, forming acids or oil soaps, result in an increase of the electrical conductivity, which directly correlates with the degree of contamination of the oil. For additivated lubricants, the stage of degradation of the additives can also be derived from changes in the dielectric constant. The determination of impurities or reduction in the quality of the oil and the quasi continuous evaluation of wear and chemical aging follow the holistic approach of a real-time monitoring of an alteration in the condition of the oil-machine system. Once the oil condition monitoring sensors are installed on the wind turbine, industrial gearbox and test stands, the measuring data can be displayed and evaluated elsewhere. The signals are transmitted to a web-based condition monitoring system via LAN, WLAN or serial interfaces of the sensor unit. Monitoring of the damage mechanisms during proper operation below the tolerance limits of the components enables specific preventive maintenance independent of rigid inspection intervals.

  4. A Formulation of Asymptotic and Exact Boundary Conditions Using Local Operators

    Science.gov (United States)

    Hagstrom, T.; Hariharan, S. I.

    1998-01-01

    In this paper we describe a systematic approach for constructing asymptotic boundary conditions for isotropic wave-like equations using local operators. The conditions take a recursive form with increasing order of accuracy. In three dimensions the recursion terminates and the resulting conditions are exact for solutions which are described by finite combinations of angular spherical harmonics. First, we develop the expansion for the two-dimensional wave equation and construct a sequence of easily implementable boundary conditions. We show that in three dimensions and analogous conditions are again easily implementable in addition to being exact. Also, we provide extensions of these ideas to hyperbolic systems. Namely, Maxwell's equations for TM waves are used to demonstrate the construction. Finally, we provide numerical examples to demonstrate the effectiveness of these conditions for a model problem governed by the wave equation.

  5. Modelling the Cost Performance of a Given Logistics Network Operating Under Regular and Irregular Conditions

    NARCIS (Netherlands)

    Janic, M.

    2009-01-01

    This paper develops an analytical model for the assessment of the cost performance of a given logistics network operating under regular and irregular (disruptive) conditions. In addition, the paper aims to carry out a sensitivity analysis of this cost with respect to changes of the most influencing

  6. [Working conditions and professional risk for operational personnel of energy facilities].

    Science.gov (United States)

    Amirov, N Kh; Ilyukhin, N E; Rusin, M N; Krasnoshchekova, V N

    2013-01-01

    Features of working conditions and a state of health of operation personnel of the network companies of power industry were studied for the purpose of justification and introduction of preventive actions for the decrease in influence of factors of professional risk.

  7. Modelling the Cost Performance of a Given Logistics Network Operating Under Regular and Irregular Conditions

    NARCIS (Netherlands)

    Janic, M.

    2009-01-01

    This paper develops an analytical model for the assessment of the cost performance of a given logistics network operating under regular and irregular (disruptive) conditions. In addition, the paper aims to carry out a sensitivity analysis of this cost with respect to changes of the most influencing

  8. Does arousal interfere with operant conditioning of spike-wave discharges in genetic epileptic rats?

    NARCIS (Netherlands)

    Osterhagen, L.; Breteler, M.H.M.; Luijtelaar, E.L.J.M. van

    2010-01-01

    One of the ways in which brain computer interfaces can be used is neurofeedback (NF). Subjects use their brain activation to control an external device, and with this technique it is also possible to learn to control aspects of the brain activity by operant conditioning. Beneficial effects of NF

  9. Appetitive operant conditioning in mice: heritability and dissociability of training stages

    NARCIS (Netherlands)

    Malkki, H.A.I.; Donga, L.A.B.; de Groot, S.E.; Battaglia, F.P.; Brussaard, A.B.; Borst, J.G.G.; Elgersma, Y.; Galjart, N.; van der Horst, G.T.; Levelt, C.N.; Pennartz, C.M.A.; Smit, A.B.; Spruijt, B.M.; Verhage, M.; de Zeeuw, C.I.

    2010-01-01

    To study the heritability of different training stages of appetitive operant conditioning, we carried out behavioral screening of 5 standard inbred mouse strains, 28 recombinant-inbred (BxD) mouse lines and their progenitor strains C57BL/6J and DBA/2J. We also computed correlations between

  10. [Microbial air purity in hospitals. Operating theatres with air conditioning system].

    Science.gov (United States)

    Krogulski, Adam; Szczotko, Maciej

    2010-01-01

    The aim of this study was to show the influence of air conditioning control for microbial contamination of air inside the operating theatres equipped with correctly working air-conditioning system. This work was based on the results of bacteria and fungi concentration in hospital air obtained since 2001. Assays of microbial air purity conducted on atmospheric air in parallel with indoor air demonstrated that air filters applied in air-conditioning systems worked correctly in every case. To show the problem of fluctuation of bacteria concentration more precisely, every sequences of single results from successive measure series were examined independently.

  11. Predators in training: operant conditioning of novel behavior in wild Burmese pythons (Python molurus bivitattus).

    Science.gov (United States)

    Emer, Sherri A; Mora, Cordula V; Harvey, Mark T; Grace, Michael S

    2015-01-01

    Large pythons and boas comprise a group of animals whose anatomy and physiology are very different from traditional mammalian, avian and other reptilian models typically used in operant conditioning. In the current study, investigators used a modified shaping procedure involving successive approximations to train wild Burmese pythons (Python molurus bivitattus) to approach and depress an illuminated push button in order to gain access to a food reward. Results show that these large, wild snakes can be trained to accept extremely small food items, associate a stimulus with such rewards via operant conditioning and perform a contingent operant response to gain access to a food reward. The shaping procedure produced robust responses and provides a mechanism for investigating complex behavioral phenomena in massive snakes that are rarely studied in learning research.

  12. Optimum operating conditions for an adsorption cryocooler: a case of activated carbon + nitrogen system

    Energy Technology Data Exchange (ETDEWEB)

    Radhika Rani Rao [Don Bosco Institute of Technology, Bangalore (India). Dept. of Physics; Madhu Prasad [ISRO Satellite Centre, Bangalore (India). Thermal Systems Group; Kandadai Srinivasan [Indian Institute of Science, Bangalore (India). Dept. of Mechanical Engineering

    2005-03-01

    Adsorption cryocoolers are among the possible options for obtaining cryogenic temperatures, in particular for small cooling capacity applications such as cooling of infra red detectors. They need to be optimized for liquid yield. The performance of thermal compressors therein pivots around the adsorption characteristics of the adsorbent + adsorbate combination and how effectively one could pack requisite amounts of adsorbent into a given volume of the compressor housing. In addition, the overall performance of the cooler is a function of limits of operating temperatures and pressures across the compressor. This paper proposes a performance indicator-the product of liquid yield and the uptake efficiency of the compressor - and evaluates its values for various possible operating conditions for one specimen of activated carbon. It is shown that there is a limited domain of operation and that there is a condition of best performance within that domain. (author)

  13. Molten Carbonate Fuel Cell performance analysis varying cathode operating conditions for carbon capture applications

    Science.gov (United States)

    Audasso, Emilio; Barelli, Linda; Bidini, Gianni; Bosio, Barbara; Discepoli, Gabriele

    2017-04-01

    The results of a systematic experimental campaign to verify the impact of real operating conditions on the performance of a complete Molten Carbonate Fuel Cell (MCFC) are presented. In particular, the effects of ageing and composition of water, oxygen and carbon dioxide in the cathodic feeding stream are studied through the analysis of current-voltage curves and Electrochemical Impedance Spectroscopy (EIS). Based on a proposed equivalent electrical circuit model and a fitting procedure, a correlation is found among specific operating parameters and single EIS coefficients. The obtained results suggest a new performance monitoring approach to be applied to MCFC for diagnostic purpose. Particular attention is devoted to operating conditions characteristic of MCFC application as CO2 concentrators, which, by feeding the cathode with exhaust gases, is a promising route for efficient and cheap carbon capture.

  14. Analysis of critical operating conditions for LV distribution networks with microgrids

    Science.gov (United States)

    Zehir, M. A.; Batman, A.; Sonmez, M. A.; Font, A.; Tsiamitros, D.; Stimoniaris, D.; Kollatou, T.; Bagriyanik, M.; Ozdemir, A.; Dialynas, E.

    2016-11-01

    Increase in the penetration of Distributed Generation (DG) in distribution networks, raises the risk of voltage limit violations while contributing to line losses. Especially in low voltage (LV) distribution networks (secondary distribution networks), impacts of active power flows on the bus voltages and on the network losses are more dominant. As network operators must meet regulatory limitations, they have to take into account the most critical operating conditions in their systems. In this study, it is aimed to present the impact of the worst operation cases of LV distribution networks comprising microgrids. Simulation studies are performed on a field data-based virtual test-bed. The simulations are repeated for several cases consisting different microgrid points of connection with different network loading and microgrid supply/demand conditions.

  15. Conceptualising the Impact of Arousal and Affective State on Training Outcomes of Operant Conditioning

    Directory of Open Access Journals (Sweden)

    Paul D. McGreevy

    2013-04-01

    Full Text Available Animal training relies heavily on an understanding of species-specific behaviour as it integrates with operant conditioning principles. Following on from recent studies showing that affective states and arousal levels may correlate with behavioural outcomes, we explore the contribution of both affective state and arousal in behavioural responses to operant conditioning. This paper provides a framework for assessing how affective state and arousal may influence the efficacy of operant training methods. It provides a series of three-dimensional conceptual graphs as exemplars to describing putative influences of both affective state and arousal on the likelihood of dogs and horses performing commonly desired behaviours. These graphs are referred to as response landscapes, and they highlight the flexibility available for improving training efficacy and the likely need for different approaches to suit animals in different affective states and at various levels of arousal. Knowledge gaps are discussed and suggestions made for bridging them.

  16. Effects of dynamic operating conditions on nitrification in biological rapid sand filters for drinking water treatment

    DEFF Research Database (Denmark)

    Lee, Carson Odell; Boe-Hansen, Rasmus; Musovic, Sanin

    2014-01-01

    Biological rapid sand filters are often used to remove ammonium from groundwater for drinking water supply. They often operate under dynamic substrate and hydraulic loading conditions, which can lead to increased levels of ammonium and nitrite in the effluent. To determine the maximum nitrification...... operating conditions. The ammonium removal rate of the filter was determined by the ammonium loading rate, but was independent of both the flow and influent ammonium concentration individually. Ammonia-oxidizing bacteria and archaea were almost equally abundant in the filter. Both ammonium removal...... rates and safe operating windows of rapid sand filters, a pilot scale rapid sand filter was used to test short-term increased ammonium loads, set by varying either influent ammonium concentrations or hydraulic loading rates. Ammonium and iron (flock) removal were consistent between the pilot...

  17. Performance evaluation of the DCMD desalination process under bench scale and large scale module operating conditions

    KAUST Repository

    Francis, Lijo

    2014-04-01

    The flux performance of different hydrophobic microporous flat sheet commercial membranes made of poly tetrafluoroethylene (PTFE) and poly propylene (PP) was tested for Red Sea water desalination using the direct contact membrane distillation (DCMD) process, under bench scale (high δT) and large scale module (low δT) operating conditions. Membranes were characterized for their surface morphology, water contact angle, thickness, porosity, pore size and pore size distribution. The DCMD process performance was optimized using a locally designed and fabricated module aiming to maximize the flux at different levels of operating parameters, mainly feed water and coolant inlet temperatures at different temperature differences across the membrane (δT). Water vapor flux of 88.8kg/m2h was obtained using a PTFE membrane at high δT (60°C). In addition, the flux performance was compared to the first generation of a new locally synthesized and fabricated membrane made of a different class of polymer under the same conditions. A total salt rejection of 99.99% and boron rejection of 99.41% were achieved under extreme operating conditions. On the other hand, a detailed water characterization revealed that low molecular weight non-ionic molecules (ppb level) were transported with the water vapor molecules through the membrane structure. The membrane which provided the highest flux was then tested under large scale module operating conditions. The average flux of the latter study (low δT) was found to be eight times lower than that of the bench scale (high δT) operating conditions.

  18. 3rd International Conference on Condition Monitoring of Machinery in Non-Stationary Operations

    CERN Document Server

    Rubini, Riccardo; D'Elia, Gianluca; Cocconcelli, Marco; Chaari, Fakher; Zimroz, Radoslaw; Bartelmus, Walter; Haddar, Mohamed

    2014-01-01

    This book presents the processings of the third edition of the Condition Monitoring of Machinery in Non-Stationary Operations (CMMNO13) which was held in Ferrara, Italy. This yearly event merges an international community of researchers who met – in 2011 in Wroclaw (Poland) and in 2012 in Hammamet (Tunisia) – to discuss issues of diagnostics of rotating machines operating in complex motion and/or load conditions. The growing interest of the industrial world on the topics covered by the CMMNO13 involves the fields of packaging, automotive, agricultural, mining, processing and wind machines in addition to that of the systems for data acquisition.The participation of speakers and visitors from industry makes the event an opportunity for immediate assessment of the potential applications of advanced methodologies for the signal analysis. Signals acquired from machines often contain contributions from several different components as well as noise. Therefore, the major challenge of condition monitoring is to po...

  19. Relationship between container ship underwater noise levels and ship design, operational and oceanographic conditions

    Science.gov (United States)

    McKenna, Megan F.; Wiggins, Sean M.; Hildebrand, John A.

    2013-05-01

    Low-frequency ocean ambient noise is dominated by noise from commercial ships, yet understanding how individual ships contribute deserves further investigation. This study develops and evaluates statistical models of container ship noise in relation to design characteristics, operational conditions, and oceanographic settings. Five-hundred ship passages and nineteen covariates were used to build generalized additive models. Opportunistic acoustic measurements of ships transiting offshore California were collected using seafloor acoustic recorders. A 5-10 dB range in broadband source level was found for ships depending on the transit conditions. For a ship recorded multiple times traveling at different speeds, cumulative noise was lowest at 8 knots, 65% reduction in operational speed. Models with highest predictive power, in order of selection, included ship speed, size, and time of year. Uncertainty in source depth and propagation affected model fit. These results provide insight on the conditions that produce higher levels of underwater noise from container ships.

  20. Droplets spectrum of air-assisted boom sprayers under different environmental and operational conditions

    Directory of Open Access Journals (Sweden)

    Robson S. Sasaki

    2016-01-01

    Full Text Available ABSTRACT During pesticide spraying, the psychrometric conditions of the air may cause evaporation of the droplets along their trajectory from the nozzle to the target. Thus, this study aimed to evaluate the effect of air psychrometric conditions and operating pressure on the droplet spectrum of air-assisted boom sprayers. The test was performed using a prototype equipped with an axial fan, a flow homogenizer, temperature and relative air humidity sensors, a spray nozzle and a gas-heating system to warm up the airflow. With the assembled system and the aid of a particle analyser, the JSF 11002 spray nozzle was evaluated with respect to droplet spectrum in four air psychrometric conditions (7, 14, 21 and 28 hPa and at four operating pressures (200, 300, 400 and 500 kPa. At the end, evaporation losses were observed during the sprayings. For a given operating pressure and for each increment of 1 hPa in vapor pressure deficit, there was a diameter reduction of approximately 0.0759, 0.518 and 1.514 μm for the parameters DV0.1, DV0.5 and DV0.9, respectively. The diameter of the droplets decreased as the operating pressure increased.

  1. Structural characterization and condition for measurement statistics preservation of a unital quantum operation

    Science.gov (United States)

    Lee, Kai-Yan; Fung, Chi-Hang Fred; Chau, H. F.

    2013-05-01

    We investigate the necessary and sufficient condition for a convex cone of positive semidefinite operators to be fixed by a unital quantum operation ϕ acting on finite-dimensional quantum states. By reducing this problem to the problem of simultaneous diagonalization of the Kraus operators associated with ϕ, we can completely characterize the kinds of quantum states that are fixed by ϕ. Our work has several applications. It gives a simple proof of the structural characterization of a unital quantum operation that acts on finite-dimensional quantum states—a result not explicitly mentioned in earlier studies. It also provides a necessary and sufficient condition for determining what kind of measurement statistics is preserved by a unital quantum operation. Finally, our result clarifies and extends the work of Størmer by giving a proof of a reduction theorem on the unassisted and entanglement-assisted classical capacities, coherent information, and minimal output Renyi entropy of a unital channel acting on a finite-dimensional quantum state.

  2. On conditions for invertibility of difference and differential operators in weight spaces

    Energy Technology Data Exchange (ETDEWEB)

    Bichegkuev, Mairbek S [North-Ossetia State University, Vladikavkaz (Russian Federation)

    2011-08-31

    We obtain necessary and sufficient conditions for the invertibility of the difference operator D{sub E}:D(D{sub E}) subset of l{sup p}{sub {alpha}}{yields}l{sup p}{sub {alpha}}, (D{sub E} x)(n)=x(n+1)-Bx(n), n element of Z{sub +}, whose domain D(D{sub E}) is given by the condition x(0) element of E, where l{sup p}{sub {alpha}}=l{sup p}{sub {alpha}}(Z{sub +},X), p element of [1,{infinity}], is the Banach space of sequences (of vectors in a Banach space X) summable with weight {alpha}:Z{sub +}{yields}(0,{infinity}) for p element of [1,{infinity}) and bounded with respect to {alpha} for p={infinity}, B:X{yields}X is a bounded linear operator, and E is a closed B-invariant subspace of X. We give applications to the invertibility of differential operators with an unbounded operator coefficient (the generator of a strongly continuous operator semigroup) in weight spaces of functions.

  3. Reactivity variation's analysis in nuclear propulsion considering the operational real conditions requirements

    Energy Technology Data Exchange (ETDEWEB)

    Pires, Leonardo Paredes; Santos, Rubens Souza dos; Lapa, Marcelo Franklin, E-mail: leonardo_paredes@icloud.com, E-mail: lapa@ien.gov.br, E-mail: rsantos@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2015-07-01

    The work presented in this paper highlights the need for the study to determine the reactivity variation ramps needed and possible to meet the real operational conditions required by a nuclear submarine in this several operating phases. In accordance with the operational needs and necessary maneuvers in certain tactical situations, large power variations in the propulsion are demanded. As these sudden and severe changes in propulsion come from the thermal power of nuclear origin, the operation of the nuclear island has to know what kind of answers and criticality variations are necessary to meet each demand speed required. It should be noted that these criticality inserts are conditioned, not only by the propulsion needs, but fundamentally by the imperative need to ensure the core integrity and the chain reaction sustainability considering the phenomenons and complex effects, nonlinear and retro-fed involved. It has to be determined what is the past and required time for each criticality insertion is perceived as motor power. Considering the highlighted aspects, this article concludes and indicates to its end, the need to establish a base operating transitional agenda, according to the naval combat doctrine, to be tested and analyzed under the aspects and peculiarities of kinetic reactors, with the purpose of being generated the appropriate criticality curves for each real need and their respective times of anticipated action. (author)

  4. Extended necessary condition for local operations and classical communication: Tight bound for all measurements

    Science.gov (United States)

    Cohen, Scott M.

    2015-06-01

    We give a necessary condition that a separable measurement can be implemented by local quantum operations and classical communication (LOCC) in any finite number of rounds of communication, generalizing and strengthening a result obtained previously. That earlier result involved a bound that is tight when the number of measurement operators defining the measurement is relatively small. The present results generalize that bound to one that is tight for any finite number of measurement operators, and we also provide an extension which holds when that number is infinite. We apply these results to the famous example on a 3 ×3 system known as "domino states," which were the first demonstration of nonlocality without entanglement. Our extended necessary condition provides another way of showing that these states cannot be perfectly distinguished by (finite-round) LOCC. It directly shows that this conclusion also holds for their related rotated domino states. We also introduce a class of problems involving the unambiguous discrimination of quantum states, each of which is an example where the states can be optimally discriminated by a separable measurement, but according to our condition, cannot be optimally discriminated by LOCC. These examples nicely illustrate the usefulness of the present results, since our earlier necessary condition, which the present result generalizes, is not strong enough to reach a conclusion in any of these cases.

  5. Online Condition Monitoring to Enable Extended Operation of Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, Ryan M.; Bond, Leonard J.; Ramuhalli, Pradeep

    2012-03-31

    Safe, secure, and economic operation of nuclear power plants will remain of strategic significance. New and improved monitoring will likely have increased significance in the post-Fukushima world. Prior to Fukushima, many activities were already underway globally to facilitate operation of nuclear power plants beyond their initial licensing periods. Decisions to shut down a nuclear power plant are mostly driven by economic considerations. Online condition monitoring is a means to improve both the safety and economics of extending the operating lifetimes of nuclear power plants, enabling adoption of proactive aging management. With regard to active components (e.g., pumps, valves, motors, etc.), significant experience in other industries has been leveraged to build the science base to support adoption for online condition-based maintenance and proactive aging management in the nuclear industry. Many of the research needs are associated with enabling proactive management of aging in passive components (e.g., pipes, vessels, cables, containment structures, etc.). This paper provides an overview of online condition monitoring for the nuclear power industry with an emphasis on passive components. Following the overview, several technology/knowledge gaps are identified, which require addressing to facilitate widespread online condition monitoring of passive components.

  6. Large eddy simulation of cooling flows in underground subway station according to different PSD operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Jang, Yong Jun; Kim, Jin Ho; Park, Sung Huk; Koo, Dong Hoe [Korea Railroad Research Institute, Uiwang (Korea, Republic of)

    2015-11-15

    Large eddy simulation (LES) method is applied to systematically investigate the cooling fluid flow and the temperature distribution under the operating of air conditioning in the deeply underground subway station. The Shin-Gum-Ho subway station in Seoul which is the 8{sup th} floor and 43.6 m deep is selected for this analysis. The entire station is covered for simulation. The ventilation mode for air conditioning is kept as ordinary state. Different operating conditions for Platform screen door (PSD) are applied. First one is PSD is completely close and second one is PSD is regularly open and close which imitate the actual circumstances in the platform. The ventilation diffusers are modeled as 95 square shapes in the lobby and 222 squares in the platform. The temperature variations and flow behaviors are numerically simulated after operating of air conditioning for the whole station and the calculated results are compared with experimental data. LES method solves the momentum and thermal equations. Werner-Wengle wall law is applied to viscous sub layers for near wall resolution. The total grid numbers are 7.5 million and the whole domain is divided to 22 blocks. Multi blocks are computed in parallel using MPI. The results show the temperature difference in the platform between PSD-close and PSD-regularly open and close cases is 3-4 .deg. C.

  7. Simulation Evaluation of Controller-Managed Spacing Tools under Realistic Operational Conditions

    Science.gov (United States)

    Callantine, Todd J.; Hunt, Sarah M.; Prevot, Thomas

    2014-01-01

    Controller-Managed Spacing (CMS) tools have been developed to aid air traffic controllers in managing high volumes of arriving aircraft according to a schedule while enabling them to fly efficient descent profiles. The CMS tools are undergoing refinement in preparation for field demonstration as part of NASA's Air Traffic Management (ATM) Technology Demonstration-1 (ATD-1). System-level ATD-1 simulations have been conducted to quantify expected efficiency and capacity gains under realistic operational conditions. This paper presents simulation results with a focus on CMS-tool human factors. The results suggest experienced controllers new to the tools find them acceptable and can use them effectively in ATD-1 operations.

  8. Numerical simulations of the first operational conditions of the negative ion test facility SPIDER

    Energy Technology Data Exchange (ETDEWEB)

    Serianni, G., E-mail: gianluigi.serianni@igi.cnr.it; Agostinetti, P.; Antoni, V.; Baltador, C.; Chitarin, G.; Marconato, N.; Pasqualotto, R.; Sartori, E.; Toigo, V.; Veltri, P. [Consorzio RFX (CNR, ENEA, INFN, UNIPD, Acciaierie Venete SpA), Corso Stati Uniti 4, 35127 Padova (Italy); Cavenago, M. [INFN-LNL, Viale dell’Università n. 2, 35020 Legnaro (Italy)

    2016-02-15

    In view of the realization of the negative ion beam injectors for ITER, a test facility, named SPIDER, is under construction in Padova (Italy) to study and optimize production and extraction of negative ions. The present paper is devoted to the analysis of the expected first operations of SPIDER in terms of single-beamlet and multiple-beamlet simulations of the hydrogen beam optics in various operational conditions. The effectiveness of the methods adopted to compensate for the magnetic deflection of the particles is also assessed. Indications for a sequence of the experimental activities are obtained.

  9. EFFECT OF OPERATION CONDITIONS ON CHANGE OF PUBLIC AND PRIVATE EFFICIENCY OF THE CAR

    Directory of Open Access Journals (Sweden)

    S. Krivoshapov

    2015-12-01

    Full Text Available The basic principles of analytical determination of the efficiency of the entire vehicle and individual units are stated. The dependences of change of the efficiency depending on the speed and load modes of vehicle operation are specified. The mathematical model takes into account the real characteristics of the road and transport machines operating conditions. The results of calculation of the indicator and the mechanical efficiency of the engine, transmission and the wheel efficiency, total efficiency of the car, depending on the category of roads, weight and the speed of the machine on example of GAZ-3307 truck are presented.

  10. Operational Reliability Assessment of Compressor Gearboxes with Normalized Lifting Wavelet Entropy from Condition Monitoring Information

    Directory of Open Access Journals (Sweden)

    Xiaoli Zhang

    2015-05-01

    Full Text Available Classical reliability assessment methods have predominantly focused on probability and statistical theories, which are insufficient in assessing the operational reliability of individual mechanical equipment with time-varying characteristics. A new approach to assess machinery operational reliability with normalized lifting wavelet entropy from condition monitoring information is proposed, which is different from classical reliability assessment methods depending on probability and statistics analysis. The machinery vibration signals with time-varying operational characteristics are firstly decomposed and reconstructed by means of a lifting wavelet package transform. The relative energy of every reconstructed signal is computed as an energy percentage of the reconstructed signal in the whole signal energy. Moreover, a normalized lifting wavelet entropy is defined by the relative energy to reveal the machinery operational uncertainty. Finally, operational reliability degree is defined by the quantitative value obtained by the normalized lifting wavelet entropy belonging to the range of [0, 1]. The proposed method is applied in the operational reliability assessment of the gearbox in an oxy-generator compressor to validate the effectiveness.

  11. Solutions from boundary condition changing operators in open string field theory

    CERN Document Server

    Kiermaier, Michael; Soler, Pablo

    2010-01-01

    We construct analytic solutions of open string field theory using boundary condition changing (bcc) operators. We focus on bcc operators with vanishing conformal weight such as those for regular marginal deformations of the background. For any Fock space state phi, the component string field of the solution Psi exhibits a remarkable factorization property: it is given by the matter three-point function of phi with a pair of bcc operators, multiplied by a universal function that only depends on the conformal weight of phi. This universal function is given by a simple integral expression that can be computed once and for all. The three-point functions with bcc operators are thus the only needed physical input of the particular open string background described by the solution. We illustrate our solution with the example of the rolling tachyon profile, for which we prove convergence analytically. The form of our solution, which involves bcc operators instead of explicit insertions of the marginal operator, can b...

  12. Study of Solids and Gas Distribution in Spouted Bed Operated In Stable and Unstable Conditions

    Directory of Open Access Journals (Sweden)

    Alwan, G. M.,

    2014-02-01

    Full Text Available A spouted bed is a special case of fluidization. It is an effective means of contacting gas with coarse solid particles. Spouted beds should be designed and operated to overcome performance instability and improves the uniform distribution of particles. Steady-state measurements were carried out in the 0.152 m ID cylindrical spouted bed made of Plexiglas that used 60° conical shape spout-air bed. The evaluation of solid and gas holdup in the two regions of spouted bed at stable and an unstable condition was performed using optical probe. The comparison of the radial profiles at the two conditions showed that the variation was in the spout region. The annulus region had similar profiles in both the condition as it acts as a loose packed bed, moving slowly downward. Stable bed was obtained at low gas velocity of 0.74 m/s and instability of spouting was observed at high gas velocity of 1.4 m/s. The beads can fluidize homogenously at stable conditions, while pulsation of the bed was appeared at unstable spout. Different flow regimes and characteristics can be obtained with minor variations in geometry or operating conditions.

  13. Plow longwall operations under challenging geological conditions; Durchoerterung von Stoerungen mit Hobelstreben

    Energy Technology Data Exchange (ETDEWEB)

    Voss, Heinz-Werner [RAG Anthrazit Ibbenbueren GmbH, Ibbenbueren (Germany); Witthaus, Holger; Junker, Martin [RAG Mining Solutions GmbH, Herne (Germany)

    2012-11-01

    In German coal mining, comprehensive experience is available in the grading of geological faults. The available experience has produced a level of expertise which enables the maintenance of high production figures even under difficult conditions. This is demonstrated by the many successful projects of RAG. The paper describes in the following several successful case examples and illustrates that the collected know-how can be used globally, even for future challenges, by German RAG Mining Solutions GmbH to successfully operate modern high-performance plough companies under difficult conditions. (orig.)

  14. Operating conditions effect over the coupling strength for urban aerial ropeways

    Directory of Open Access Journals (Sweden)

    Ronald M. MARTINOD

    2014-09-01

    Full Text Available The present work is aimed to assess the operating conditions effect for urban aerial ropeways with a commercial usage, based on measurements obtained from an arrangement of sensors that record the coupling assembly behavior between the detachable gondola pod and the track rope. The work pays particular attention to the effect caused by external conditions due to the wind loads joined up with other parasite external effects, through the measurement of the engage strains. The cableway gondola continuous cycle has mono-cable of simple ring type.

  15. Response Load Extrapolation for Wind Turbines during Operation Based on Average Conditional Exceedance Rates

    DEFF Research Database (Denmark)

    Toft, Henrik Stensgaard; Naess, Arvid; Saha, Nilanjan;

    2011-01-01

    The paper explores a recently developed method for statistical response load (load effect) extrapolation for application to extreme response of wind turbines during operation. The extrapolation method is based on average conditional exceedance rates and is in the present implementation restricted......-of-plane bending moment and the tower mudline bending moment of a pitch-controlled wind turbine. In general, the results show that the method based on average conditional exceedance rates predicts the extrapolated characteristic response loads at the individual mean wind speeds well and results in more consistent...

  16. A class of ${\\rm II_1}$ factors with an exotic abelian maximal amenable subalgebra

    CERN Document Server

    Houdayer, Cyril

    2012-01-01

    We show that for every mixing orthogonal representation $\\pi : \\Z \\to \\mathcal O(H_\\R)$, the abelian subalgebra $\\LL(\\Z)$ is maximal amenable in the crossed product ${\\rm II}_1$ factor $\\Gamma(H_\\R)\\dpr \\rtimes_\\pi \\Z$ associated with the free Bogoljubov action of the representation $\\pi$. This provides uncountably many non-isomorphic $A$-$A$-bimodules which are disjoint from the coarse $A$-$A$-bimodule and of the form $\\LL^2(M \\ominus A)$ where $A \\subset M$ is a maximal amenable masa in a ${\\rm II_1}$ factor.

  17. High-speed flow visualization in a pump-turbine under off-design operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Hasmatuchi, V; Roth, S; Botero, F; Avellan, F; Farhat, M, E-mail: vlad.hasmatuchi@epfl.c [Laboratory for Hydraulic Machines, Ecole Polytechnique Federale de Lausanne Av. de Cour 33bis, Lausanne, CH-1007 (Switzerland)

    2010-08-15

    The flow hydrodynamics in a low specific speed radial pump-turbine reduced scale model is experimentally investigated under off-design operating conditions in generating mode. Wall pressure measurements, in the stator, synchronized with high-speed flow visualizations in the vaneless space between the impeller and the guide vanes using air bubbles injection are performed. When starting from the best efficiency point and increasing the runner speed, a significant increase of the pressure fluctuations is observed mainly in channels between wicket gates. The spectral analysis shows a rise of one stall cell, rotating with about 70% of the impeller frequency, at runaway, which further increases as the zero discharge condition is approached. Then a specific image processing technique is detailed and applied to create a synthetic instantaneous view of the flow pattern on the entire guide vanes circumference for an operating point in turbine-brake mode, where backflow and vortices accompany the stall passage.

  18. Compliance with Operational Circular No. 2 on conditions of access to the fenced CERN sites

    CERN Multimedia

    Relations with the Host States Service

    2004-01-01

    The purpose of Operational Circular No. 2 is to contribute to the protection of people and property by defining the conditions of access to the Organization's fenced sites. However, recently, the services concerned have noted a significant increase in the instances of non-compliance with those conditions that cannot be tolerated, for example: use of CERN access cards by people, other than the cardholders themselves, in order to gain access to facilities without having attended the required safety course; speeding, particularly on Route Gregory and Route Weisskopf; driving in and out of the site on the wrong side of the road; parking on spaces set aside for the disabled; nuisance parking, especially in the proximity of the Restaurants; the dumping of wrecked vehicles. As the aforementioned instances of non-compliance can lead to dangerous situations, the Organization reserves the right to apply the penalties provided for under paragraph 26 of Operational Circular No. 2, namely to refuse access to the site...

  19. REMINDER - Compliance with Operational Circular No. 2 on conditions of access to the fenced CERN sites

    CERN Multimedia

    Relations with the Host States Service

    2004-01-01

    The purpose of Operational Circular No. 2 is to contribute to the protection of people and property by defining the conditions of access to the Organization's fenced sites. However, recently, the services concerned have noted a significant increase in the instances of non-compliance with those conditions that cannot be tolerated, for example: use of CERN access cards by people, other than the cardholders themselves, in order to gain access to facilities without having attended the required safety course; speeding, particularly on Route Gregory and Route Weisskopf; driving in and out of the site on the wrong side of the road; parking on spaces set aside for the disabled; nuisance parking, especially in the proximity of the Restaurants; the dumping of wrecked vehicles. As the aforementioned instances of non-compliance can lead to dangerous situations, the Organization reserves the right to apply the penalties provided for under paragraph 26 of Operational Circular No. 2, namely to refuse access to the site ...

  20. Operating wind turbines in strong wind conditions by using feedforward-feedback control

    Science.gov (United States)

    Feng, Ju; Sheng, Wen Zhong

    2014-12-01

    Due to the increasing penetration of wind energy into power systems, it becomes critical to reduce the impact of wind energy on the stability and reliability of the overall power system. In precedent works, Shen and his co-workers developed a re-designed operation schema to run wind turbines in strong wind conditions based on optimization method and standard PI feedback control, which can prevent the typical shutdowns of wind turbines when reaching the cut-out wind speed. In this paper, a new control strategy combing the standard PI feedback control with feedforward controls using the optimization results is investigated for the operation of variable-speed pitch-regulated wind turbines in strong wind conditions. It is shown that the developed control strategy is capable of smoothening the power output of wind turbine and avoiding its sudden showdown at high wind speeds without worsening the loads on rotor and blades.

  1. Operating wind turbines in strong wind conditions by using feedforward-feedback control

    DEFF Research Database (Denmark)

    Feng, Ju; Shen, Wen Zhong

    2014-01-01

    the optimization results is investigated for the operation of variable-speed pitch-regulated wind turbines in strong wind conditions. It is shown that the developed control strategy is capable of smoothening the power output of wind turbine and avoiding its sudden showdown at high wind speeds without worsening......Due to the increasing penetration of wind energy into power systems, it becomes critical to reduce the impact of wind energy on the stability and reliability of the overall power system. In precedent works, Shen and his co-workers developed a re-designed operation schema to run wind turbines...... in strong wind conditions based on optimization method and standard PI feedback control, which can prevent the typical shutdowns of wind turbines when reaching the cut-out wind speed. In this paper, a new control strategy combing the standard PI feedback control with feedforward controls using...

  2. Detection of Partial Demagnetization Fault in PMSMs Operating under Nonstationary Conditions

    DEFF Research Database (Denmark)

    Wang, Chao; Delgado Prieto, Miguel; Romeral, Luis

    2016-01-01

    Demagnetization fault detection of in-service Permanent Magnet Synchronous Machines (PMSMs) is a challenging task because most PMSMs operate under nonstationary circumstances in industrial applications. A novel approach based on tracking characteristic orders of stator current using Vold-Kalman F......Demagnetization fault detection of in-service Permanent Magnet Synchronous Machines (PMSMs) is a challenging task because most PMSMs operate under nonstationary circumstances in industrial applications. A novel approach based on tracking characteristic orders of stator current using Vold......-Kalman Filter is proposed to detect the partial demagnetization fault in PMSMs running at nonstationary conditions. Amplitude of envelope of the fault characteristic orders is used as fault indictor. Experimental results verify the superiority of the proposed method on partial demagnetization online fault...... detection of PMSMs under various speed and load conditions....

  3. Thermal-hydraulics of LLCB TBM under different ITER operational conditions

    Energy Technology Data Exchange (ETDEWEB)

    Chaudhuri, Paritosh, E-mail: paritc@gmail.com; Ranjithkumar, S.; Sharma, Deepak; Danani, Chandan; Kumar, E. Rajendra

    2016-11-01

    Highlights: • Thermal analysis of LLCB TBM has been performed for different ITER operations during normal and power excursion scenarios. • It is observed that in all ITER operations, the temperatures in all components of LLCB TBM are well within the limits. • The maximum temperature of CB-1 in steady state is 920 °C, which is 72% of the maximum temperature obtained in ITER pulse. - Abstract: Lead–lithium cooled ceramic breeder (LLCB) TBM is the Indian DEMO relevant blanket module, which will be tested in one-half of a designated ITER port from day 1 operation of ITER. LLCB TBM will be tested in various ITER operational phases. Different TBM may be tested corresponding to the four different phases of plasma operation. The paper present a review of thermal analyses based on the various heat loads on the LLCB TBM obtained from neutronics calculations to confirm heat removal and structural integrity under different ITER operational conditions. This includes the normal plasma operation, fusion power excursions, surface heat flux due to MARFES, disruption heat loads during thermal and current quench etc., in inductive and non-inductive plasma operations. Transient events, like plasma disruption, vertical displacement events (VDEs) and edge localized modes (ELMs) deliver considerable heat flux (high power densities) for short durations onto the first wall of TBM. Detailed thermal-hydraulic simulation studies have been performed using ANSYS. These analyses, therefore, will provide important information about the temperature distribution in different materials used in TBM and their temperature-time histories.

  4. Method for Prediction of the Power Output from Photovoltaic Power Plant under Actual Operating Conditions

    Science.gov (United States)

    Obukhov, S. G.; Plotnikov, I. A.; Surzhikova, O. A.; Savkin, K. D.

    2017-04-01

    Solar photovoltaic technology is one of the most rapidly growing renewable sources of electricity that has practical application in various fields of human activity due to its high availability, huge potential and environmental compatibility. The original simulation model of the photovoltaic power plant has been developed to simulate and investigate the plant operating modes under actual operating conditions. The proposed model considers the impact of the external climatic factors on the solar panel energy characteristics that improves accuracy in the power output prediction. The data obtained through the photovoltaic power plant operation simulation enable a well-reasoned choice of the required capacity for storage devices and determination of the rational algorithms to control the energy complex.

  5. Waste to energy plant operation under the influence of market and legislation conditioned changes

    DEFF Research Database (Denmark)

    Tomic, Tihomir; Dominkovic, Dominik Franjo; Pfeifer, Antun

    2017-01-01

    In this paper, gate-fee changes of the waste-to-energy plants are investigated in the conditions set by European Union legislation and by the introduction of the new heat market. Waste management and sustainable energy supply are core issues of sustainable development of regions, especially urban...... areas. These two energy flows logically come together in the combined heat and power facility by waste incineration. However, the implementation of new legislation influences quantity and quality of municipal waste and operation of waste-to-energy systems. Once the legislation requirements are met......, waste-to-energy plants need to be adapted to market operation. This influence is tracked by the gate-fee volatility. The operation of the waste-to-energy plant on electricity markets is simulated by using EnergyPLAN and heat market is simulated in Matlab, based on hourly marginal costs. The results have...

  6. Control of hybrid AC/DC microgrid under islanding operational conditions

    DEFF Research Database (Denmark)

    Ding, G.; Gao, F.; Zhang, S.

    2014-01-01

    This paper presents control methods for hybrid AC/DC microgrid under islanding operation condition. The control schemes for AC sub-microgrid and DC sub-microgrid are investigated according to the power sharing requirement and operational reliability. In addition, the key control schemes...... of interlinking converter with DC-link capacitor or energy storage, which will devote to the proper power sharing between AC and DC sub-microgrids to maintain AC and DC side voltage stable, is reviewed. Combining the specific control methods developed for AC and DC sub-microgrids with interlinking converter......, the whole hybrid AC/DC microgrid can manage the power flow transferred between sub-microgrids for improving on the operational quality and efficiency....

  7. Microstructure degradation of LSM-YSZ cathode in SOFCs operated at various conditions

    DEFF Research Database (Denmark)

    Liu, Yi-Lin; Thydén, Karl Tor Sune; Chen, Ming

    2012-01-01

    mechanisms have been identified. And it has been observed that different mechanisms dominate the degradation process under different test conditions. The severe cathode degradation at 750 °C operation with high current density is attributed to a loss of the cathode/electrolyte interface stability......Systematic microstructural analyses have been carried out on a series of technological SOFCs that went through long-term cell tests with various operating parameters including temperature, current load and time length under current. For the LSM-YSZ cathode, a number of microstructure degradation....... For the cells tested at 850 °C, the interface stability is maintained due to further sintering during cell operation. A cell test lasting for 2 years (17500 h) at 850 °C with a moderate current density (not greater than 1 A/cm2) has shown that the cathode microstructure is fairly robust to the degradation...

  8. Optimum operation conditions of nitrogen and phosphorus removal by a biofilm-activated-sludge system

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    In the biofilm and activated sludge combined system, denitrifying bacteria attached on the fibrous carriers in the anoxic tank, while the sludge containing nitrifying and phosphorus removal bacteria was only recirculated between the aerobic and anaerobic tanks. Therefore, the factors affected and restricted nitrification, denitrification and phosphorus removal in a traditional A/A/O process were resolved. This paper describes the optimum operation conditions for nitrogen and phosphorus removal using this system.

  9. Mechanical Properties of a Unidirectional Basalt-Fiber-Reinforced Plastic Under a Loading Simulating Operation Conditions

    Science.gov (United States)

    Lobanov, D. S.; Slovikov, S. V.

    2017-01-01

    The results of experimental investigations of unidirectional composites based on basalt fibers and different marks of epoxy resins are presented. Uniaxial tensile tests were carried out using a specimen fixation technique simulating the operation conditions of structures. The mechanical properties of the basalt-fiber-reinforced plastics (BFRPs) were determined. The diagrams of loading and deformation of BFRP specimens were obtain. The formulations of the composites with the highest mechanical properties were revealed.

  10. Temperature limits for LMFBR fuel cladding under upset and emergency operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Govindarajan, S.; Chetal, S.C. [Indira Gandhi Centre for Atomic Research, Kalpakkam Tamilnadu (India). Nuclear Systems Division

    1996-07-01

    LMFBR fuel pin cladding tube is subjected to high transient temperatures during incidents such as pump trip, pump to grid plate pipe rupture etc. It is required to know temperature limits under such transient operating conditions for components involved while analyzing such incidents. A methodology for deriving such limits for fuel clad tube is worked out in this paper by making use of the transient damage correlation proposed by W.F. Brizes et. al.

  11. Mathematical Model of Bridge-Linked Photovoltaic Arrays Operating Under Irregular Conditions

    OpenAIRE

    Juan D. Bastidas-Rodríguez; Carlos A. Ramos-Paja; Luz A. Trejos-Grisales

    2013-01-01

    This paper presents a mathematical procedure to model a photovoltaic array (N rows and M columns) in bridge-linked configuration operating under regular and irregular conditions. The proposed procedure uses the ideal single-diode model representation for each photovoltaic module and the Shockley equation to represent each bypass diode. To pose the system of NxM non-linear equations required to obtain the voltages of each module of the array, the proposed model apply the Kirchhoff current law ...

  12. EFFECTS OF OPERATING CONDITIONS ON THE DEPOSITION OF GaAs IN A VERTICAL CVD REACTOR

    OpenAIRE

    JAE-SANG BAEK; JIN-HYO BOO; YOUN-JEA KIM

    2008-01-01

    A numerical study is needed to gain insight into the growth mechanism and improve the reactor design or optimize the deposition condition in chemical vapor deposition (CVD). In this study, we have performed a numerical analysis of the deposition of gallium arsenide (GaAs) from trimethyl gallium (TMG) and arsine in a vertical CVD reactor. The effects of operating parameters, such as the rotation velocity of susceptor, inlet velocity, and inlet TMG fraction, are investigated and presented. The ...

  13. Differential gene expression in the rat hippocampus during learning of an operant conditioning task.

    Science.gov (United States)

    Rapanelli, M; Frick, L R; Zanutto, B S

    2009-11-10

    Changes in transcription levels of brain-derived neurotrophic factor (BDNF), cyclic adenosine monophosphate (cAMP) response element binding (CREB), Synapsin I, Ca(2+)/calmodulin-dependent protein kinase II (CamKII), activity-regulated cytoskeleton-associated protein (Arc), c-jun and c-fos have been associated to several learning paradigms in different brain areas. In this study, we measured mRNA expression in the hippocampus by real time (RT)-PCR mRNA levels of BDNF, CREB, Synapsin I, CamKII, Arc, c-jun and c-fos, during learning and operant conditioning task. Experimental groups were as follows: control (C, the animals never left the bioterium), when the animals reached 50-65% of the expected response (Incompletely Trained, IT), when animals reached 100% of the expected response with a latency time lower than 5 s (Trained, Tr), Box Control of Incompletely Trained (BCIT), animals spent the same time as the IT in the operant conditioning box and Box Control of Trained (BCTr) animals spent the same time as the Tr in the operant conditioning box. All rats were killed at the same time by cervical dislocation 15 min after training and hippocampi were removed and processed. We found increments of mRNA levels of most genes (BDNF, CREB, Synapsin I, Arc, c-jun and c-fos) in IT and Tr groups compared to their box controls, but increments in Tr were smaller compared with IT. These results describe a differential gene expression in the rat hippocampus when the animals are learning and when animals have already learned. Taking together the results presented herein with the known functions of these genes, we propose a link between changes in gene expression in the hippocampus and different degrees of cellular activation and plasticity during learning of an operant conditioning task.

  14. Influence of Met-Ocean Condition Forecasting Uncertainties on Weather Window Predictions for Offshore Operations

    DEFF Research Database (Denmark)

    Gintautas, Tomas; Sørensen, John Dalsgaard

    2017-01-01

    The article briefly presents a novel methodology of weather window estimation for offshore operations and mainly focuses on effects of met-ocean condition forecasting uncertainties on weather window predictions when using the proposed methodology. It is demonstrated that the proposed methodology...... to include stochastic variables, representing met-ocean forecasting uncertainties and the results of such modification are given in terms of predicted weather windows for a selected test case....

  15. Multifunctional ultrasonic sensor for on-line tool condition monitoring in turning operations

    Energy Technology Data Exchange (ETDEWEB)

    Nayfeh, T.H.; Abu-Zahra, N.H. [Cleveland State Univ., OH (United States). Industrial Engineering Dept.

    1998-03-01

    Machining operations in automated manufacturing centers are, in general, under-performing by 20--80 percent. Optimizing these machining operations requires on-line knowledge of the cutting tool`s condition and the process state. Currently, this information is either not reliable or not available in a timely manner. This in part is due to the lack of suitable sensors which are able to measure on-line directly and accurately one or more of the relevant tool and process variables. A direct, active, ultrasonic method for on-line sensing of the tool condition and the process state in turning operations was developed in this work. Sensing is achieved by using an ultrasonic transducer operating at 10 MHz in a pulse-echo mode to send pulses through the cutting tool. The amplitude and propagation time of the reflected pulses are modulated by the tool nose, flank, temperature, and by the material in contact with the tools. This method has the potential to measure on-line several relevant process and cutting tool parameters directly and accurately through the use of a single sensor. These parameters are tool-workpiece contact, tool gradual wear, tool chipping and tool chatter.

  16. Operation reliability assessment for cutting tools by applying a proportional covariate model to condition monitoring information.

    Science.gov (United States)

    Cai, Gaigai; Chen, Xuefeng; Li, Bing; Chen, Baojia; He, Zhengjia

    2012-09-25

    The reliability of cutting tools is critical to machining precision and production efficiency. The conventional statistic-based reliability assessment method aims at providing a general and overall estimation of reliability for a large population of identical units under given and fixed conditions. However, it has limited effectiveness in depicting the operational characteristics of a cutting tool. To overcome this limitation, this paper proposes an approach to assess the operation reliability of cutting tools. A proportional covariate model is introduced to construct the relationship between operation reliability and condition monitoring information. The wavelet packet transform and an improved distance evaluation technique are used to extract sensitive features from vibration signals, and a covariate function is constructed based on the proportional covariate model. Ultimately, the failure rate function of the cutting tool being assessed is calculated using the baseline covariate function obtained from a small sample of historical data. Experimental results and a comparative study show that the proposed method is effective for assessing the operation reliability of cutting tools.

  17. Impacts of operating conditions and solution chemistry on osmotic membrane structure and performance

    KAUST Repository

    Wong, Mavis C.Y.

    2012-02-01

    Herein, we report on changes in the performance of a commercial cellulose triacetate (CTA) membrane, imparted by varied operating conditions and solution chemistries. Changes to feed and draw solution flow rate did not significantly alter the CTA membrane\\'s water permeability, salt permeability, or membrane structural parameter when operated with the membrane skin layer facing the draw solution (PRO-mode). However, water and salt permeability increased with increasing feed or draw solution temperature, while the membrane structural parameter decreased with increasing draw solution, possibly due to changes in polymer intermolecular interactions. High ionic strength draw solutions may de-swell the CTA membrane via charge neutralization, which resulted in lower water permeability, higher salt permeability, and lower structural parameter. This observed trend was further exacerbated by the presence of divalent cations which tends to swell the polymer to a greater extent. Finally, the calculated CTA membrane\\'s structural parameter was lower and less sensitive to external factors when operated in PRO-mode, but highly sensitive to the same factors when the skin layer faced the feed solution (FO-mode), presumably due to swelling/de-swelling of the saturated porous substructure by the draw solution. This is a first attempt aimed at systematically evaluating the changes in performance of the CTA membrane due to operating conditions and solution chemistry, shedding new insight into the possible advantages and disadvantages of this material in certain applications. © 2011 Elsevier B.V.

  18. Soleus H-Reflex Operant Conditioning Changes The H-Reflex Recruitment Curve

    Science.gov (United States)

    Thompson, Aiko K.; Chen, Xiang Yang; Wolpaw, Jonathan R.

    2012-01-01

    Introduction Operant conditioning can gradually change the human soleus H-reflex. The protocol conditions the reflex near M-wave threshold. This study examined its impact on the reflexes at other stimulus strengths. Methods H-reflex recruitment curves were obtained before and after a 24-session exposure to an up-conditioning (HRup) or down-conditioning (HRdown) protocol and were compared. Results In both HRup and HRdown subjects, conditioning affected the entire H-reflex recruitment curve. In 5 of 6 HRup and 3 of 6 HRdown subjects, conditioning elevated (HRup) or depressed (HRdown), respectively, the entire curve. In the other HRup subject or the other 3 HRdown subjects, the curve was shifted to the left or to the right, respectively. Discussion H-reflex conditioning does not simply change the H-reflex to a stimulus of particular strength; it also changes the H-reflexes to stimuli of different strengths. Thus, it is likely to affect many actions in which this pathway participates. PMID:23281107

  19. Experimental fuel cell performance analysis under different operating conditions and bipolar plate designs

    Energy Technology Data Exchange (ETDEWEB)

    Iranzo, Alfredo; Pino, Javier; Rosa, Felipe [Energy Engineering Department, School of Engineering, University of Seville, Camino de los Descubrimientos s/n, 41092 Seville (Spain); Munoz, Miguel; Lopez, Eduardo [INTA - National Institute for Aerospace Technology, Ctra. San Juan del Puerto-Matalascanas km 33, 21130 Mazagon (Huelva) (Spain)

    2010-10-15

    This work presents experimental performance results for a 50 cm{sup 2} Polymer Electrolyte Membrane (PEM) Fuel Cell, including polarization curves and Electrochemical Impedance Spectroscopy (EIS) analysis of the Fuel Cell. EIS results were used for the determination of the cell ohmic resistance as well as charge transfer resistances under different operating conditions. Different combinations of operating conditions and bipolar plate designs were analysed. In particular, the effect of the cathode oxygen concentration, reactant gases humidification, and bipolar plate (BP) design were assessed. Butler-Volmer (BV) kinetic parameters such as the charge transfer coefficient were also determined from Tafel plots. The electronic contact resistances were measured for both Bipolar Plate designs, and the membrane protonic resistances were calculated. Its dependence on the BP flow field design and operating conditions is addressed. The results obtained in this work are aimed both at gaining insight into the fundamental processes determining the fuel cell performance, and at determining parameters needed for Computational Fuel Cell Dynamics (CFCD) numerical simulations. (author)

  20. An operant conditioning method for studying auditory behaviors in marmoset monkeys.

    Directory of Open Access Journals (Sweden)

    Evan D Remington

    Full Text Available The common marmoset (Callithrix jacchus is a small New World primate that has increasingly been used as a non-human model in the fields of sensory, motor, and cognitive neuroscience. However, little knowledge exists regarding behavioral methods in this species. Developing an understanding of the neural basis of perception and cognition in an animal model requires measurement of both brain activity and behavior. Here we describe an operant conditioning behavioral training method developed to allow controlled psychoacoustic measurements in marmosets. We demonstrate that marmosets can be trained to consistently perform a Go/No-Go auditory task in which a subject licks at a feeding tube when it detects a sound. Correct responses result in delivery of a food reward. Crucially, this operant conditioning task generates little body movement and is well suited for pairing behavior with single-unit electrophysiology. Successful implementation of an operant conditioning behavior opens the door to a wide range of new studies in the field of auditory neuroscience using the marmoset as a model system.

  1. OPTIMIZATION OF SESAME SEEDS OIL EXTRACTION OPERATING CONDITIONS USING THE RESPONSE SURFACE DESIGN METHODOLOGY

    Directory of Open Access Journals (Sweden)

    HAITHAM OSMAN

    2016-12-01

    Full Text Available This paper applies Response Surface Design (RSD to model the experimental data obtained from the extraction of sesame seeds oil using n-hexane, chloroform and acetone as solvents under different operating conditions. The results obtained revealed that n-hexane outperformed the extraction obtained using chloroform and acetone. The developed model predicted that n-hexane with a rotational speed of 547 rpm and a contact time between the solvent and seeds of 19.46 hours with solvent: seeds ratio of 4.93, yields the optimum oil extracted of 37.03 %, outperforming chloroform and acetone models that gave prediction for 4.75 and 4.21 respectively. While the maximum predictions yield for chloroform is 6.73 %, under the operating conditions of 602 rpm, and 24 hours contact time, with a ratio of solvent: seeds of 1.74. On the other hand the acetone maximum prediction is only 4.37 %, with operational conditions of 467 rpm, and 6.00 hours contact time, with a ratio of solvent: seeds of 1. It is has been found that the maximum oil extraction yield obtained from the chloroform (6.73 % and Acetone (4.37 % is much lower than that predicted by n-hexane 37.03 %.

  2. Associations of emotional arousal, dissociation and symptom severity with operant conditioning in borderline personality disorder.

    Science.gov (United States)

    Paret, Christian; Hoesterey, Steffen; Kleindienst, Nikolaus; Schmahl, Christian

    2016-10-30

    Those with borderline personality disorder (BPD) display altered evaluations regarding reward and punishment compared to others. The processing of rewards is basal for operant conditioning. However, studies addressing operant conditioning in BPD patients are rare. In the current study, an operant conditioning task combining learning acquisition and reversal was used. BPD patients and matched healthy controls (HCs) were exposed to aversive and neutral stimuli to assess the influence of emotion on learning. Picture content, dissociation, aversive tension and symptom severity were rated. Error rates were measured. Results showed no group interactions between aversive versus neutral scenes. The higher emotional arousal, dissociation and tension, the worse the acquisition, but not reversal, scores were for BPD patients. Scores from the Borderline Symptom List were associated with more errors in the reversal, but not the acquisition phase. The results are preliminary evidence for impaired acquisition learning due to increased emotional arousal, dissociation and tension in BPD patients. A failure to process punishment in the reversal phase was associated with symptom severity and may be related to neuropsychological dysfunctioning involving the ventromedial prefrontal cortex. Conclusions are limited due to the correlational study design and the small sample size. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  3. Erosion corrosion of CuCrZr specimens exposed for simulated ITER operational conditions

    Directory of Open Access Journals (Sweden)

    C. Obitz

    2016-12-01

    The erosion corrosion and release rates of CuCrZr and CuCrZr/316L(N-IG joints were derived from weight change data and metallographic examinations of specimens after autoclave exposures at 110°C, 150°C and 250°C at reducing-, oxidizing- and cyclic redox water chemistry conditions. Reducing water chemistry represents periods considered as the nominal off-plasma operational conditions while the oxidizing environment simulates situations when the plasma is active. The cyclic redox conditions represent periods with shorter cycles simulating plasma activations with subsequent periodical variation of the water chemistry from reducing to oxidizing. The erosion corrosion rates for CuCrZr at active plasma conditions were 20 and 40µm/year at 110 and 150°C. At 250°C the corresponding rate was much higher. This result gives important information on what may happen if, for example, a First Wall panel is exposed to an unexpectedly high heat flux. Under reducing conditions the erosion corrosion rates were 3µm/year and 20µm/year at 110°C and 250°C respectively. The results at 250°C under off-plasma conditions reveal that the effect of erosion corrosion also has to be taken into account during baking. Cyclic conditions with respect to oxidant content turned out to be the most demanding environment (more demanding than pure oxidizing conditions for the CuCrZr-alloy. Erosion corrosion rates of 90µm/year and 370µm/year at 110 and 150°C were recorded respectively. The highest temperature 250°C was not tested. This raise the question whether measures should be introduced that renders the system either oxidizing or reducing. In summary, the erosion corrosion rates recorded for CuCrZr under simulated ITER coolant water conditions are high, especially during plasma operation. For comparison it can be mentioned that corrosion rates of structural materials in the primary loop of light water reactors generally are considerably lower than 1µm/year. The estimated rates for Cu

  4. 75 FR 70090 - Special Conditions: Bombardier Inc. Model CL-600-2E25 Airplane, Operation Without Normal...

    Science.gov (United States)

    2010-11-17

    ... Airplane, Operation Without Normal Electrical Power AGENCY: Federal Aviation Administration (FAA), DOT... without normal electrical power,'' requires safe operation in VFR conditions for at least five minutes with inoperative normal electrical power. The applicable airworthiness regulations do not...

  5. Restoring Walking after SCI: Operant Conditioning of Spinal Reflexes Can Help

    Science.gov (United States)

    Thompson, Aiko K.; Wolpaw, Jonathan R.

    2014-01-01

    People with incomplete spinal cord injury (SCI) frequently suffer motor disabilities due to spasticity and poor muscle control, even after conventional therapy. Abnormal spinal reflex activity often contributes to these problems. Operant conditioning of spinal reflexes, which can target plasticity to specific reflex pathways, can enhance recovery. In rats in which a right lateral column lesion had weakened right stance and produced an asymmetrical gait, up-conditioning of the right soleus H-reflex, which increased muscle spindle afferent excitation of soleus, strengthened right stance and eliminated the asymmetry. In people with hyperreflexia due to incomplete SCI, down-conditioning of the soleus H-reflex improved walking speed and symmetry. Furthermore, modulation of EMG activity during walking improved bilaterally, indicating that a protocol that targets plasticity to a specific pathway can trigger widespread plasticity that improves recovery far beyond that attributable to the change in the targeted pathway. These improvements were apparent to people in their daily lives. They reported walking faster and farther, and noted less spasticity and better balance. Operant conditioning protocols could be developed to modify other spinal reflexes or corticospinal connections; and could be combined with other therapies to enhance recovery in people with SCI or other neuromuscular disorders. PMID:24636954

  6. The improving of the heat networks operating process under the conditions of the energy efficiency providing

    Directory of Open Access Journals (Sweden)

    Blinova Tatiana

    2016-01-01

    Full Text Available Among the priorities it is important to highlight the modernization and improvement of energy efficiency of housing and communal services, as well as the transition to the principle of using the most efficient technologies used in reproduction (construction, creation of objects of municipal infrastructure and housing modernization. The main hypothesis of this study lies in the fact that in modern conditions the realization of the most important priorities of the state policy in the sphere of housing and communal services, is possible in the conditions of use of the most effective control technologies for the reproduction of thermal networks. It is possible to raise the level of information security Heat Distribution Company, and other market participants by improving business processes through the development of organizational and economic mechanism in the conditions of complex monitoring of heat network operation processes

  7. Air-conditioning vs. presence of pathogenic fungi in hospital operating theatre environment.

    Science.gov (United States)

    Gniadek, Agnieszka; Macura, Anna B

    2011-01-01

    Infections related to modern surgical procedures present a difficult problem for contemporary medicine. Infections acquired during surgery represent a risk factor related to therapeutical interventions. Eradication of microorganisms from hospital operating theatre environment may contribute to reduction of infections as the laminar flow air-conditioning considerably reduces the number of microorganisms in the hospital environment. The objective of the study was to evaluate the occurrence of fungi in air-conditioned operating theatre rooms. The study was carried out in one of the hospitals in Krak6w during December 2009. Indoor air samples and imprints from the walls were collected from five operating theatre rooms. A total of fifty indoor air samples were collected with a MAS-100 device, and twenty five imprints from the walls were collected using a Count Tact method. Fungal growth was observed in 48 air samples; the average numbers of fungi were within the range of 5-100 c.f.u. in one cubic metre of the air. Fungi were detected only in four samples of the wall imprints; the number of fungi was 0.01 c.f.u. per one square centimetre of the surface. The mould genus Aspergillus was most frequently isolated, and the species A. fumigatus and A. versicolor were the dominating ones. To ensure microbiological cleanness of hospital operating theatre, the air-conditioning system should be properly maintained. Domination of the Aspergillus fungi in indoor air as well as increase in the number of moulds in the samples taken in evenings (p < 0.05) may suggest that the room decontamination procedures were neglected.

  8. Evaluating natural resource amenities in a human life expectancy production function

    Science.gov (United States)

    Neelam C. Poudyal; Donald G. Hodges; J.M. Bowker; H.K. Cordell

    2009-01-01

    This study examined the effect of natural resource amenities on human life expectancy. Extending the existing model of the life expectancy production function, and correcting for spatial dependence, we evaluated the determinants of life expectancy using county level data. Results indicate that after controlling for socio-demographic and economic factors, medical...

  9. A review of pesticide policies and regulations for urban amenity areas in seven European countries

    NARCIS (Netherlands)

    Kristoffersen, P.; Rask, A.M.; Grundy, A.; Franzen, I.; Kempenaar, C.; Raisio, J.; Schroeder, H.; Spijker, J.H.; Verschwele, A.; Zarina, L.

    2008-01-01

    An analysis of the regulations of herbicide use for weed control in non-agricultural/urban amenity areas, including actual pesticide use, was carried out as a joint survey of seven European countries: Denmark, Finland, Germany, Latvia, the Netherlands, Sweden and United Kingdom. Herbicides

  10. Local Amenities, Unobserved Quality, and Market Clearing: Adjusting Teacher Compensation to Provide Equal Education Opportunities

    Science.gov (United States)

    Tuck, Bradford; Berman, Matthew; Hill, Alexandra

    2009-01-01

    Local school districts differ in their ability to pay for teacher quality, and in the amenities they offer as places to live and work. Market clearing with heterogeneous quality yields geographically varying teacher salary levels that confound scarcity with unobserved differences in quality. The paper discusses identification and estimation of a…

  11. Groups definable in o-minimal structures: structure theorem, G^000, definable amenability and bounded orbits

    CERN Document Server

    Pillay, Anand

    2010-01-01

    We settle some open problems in the special case of groups in o-minimal structures, such as the equality of G^00 and G^000 and the equivalence of definable amenability and existence of a type with bounded orbit. We prove almost exactness of the G to G^00 functor. We ask further questions about types with bounded orbits in NIP theories.

  12. Geographical Differentials in Cost of Living, Amenities, Wages, and Cost of Government Services: Theory and Measurement.

    Science.gov (United States)

    Halstead, Kent

    The theory and procedures for measuring geographical differentials in cost of living, amenities, wages, and cost of government services are presented. These differences are important to individuals seeking optimal locations, and within groups seeking equitable treatment in locational assignments. Indexes for these factors are reported for 579…

  13. Operant Conditioning in Honey Bees (Apis mellifera L.): The Cap Pushing Response

    Science.gov (United States)

    Abramson, Charles I.; Dinges, Christopher W.; Wells, Harrington

    2016-01-01

    The honey bee has been an important model organism for studying learning and memory. More recently, the honey bee has become a valuable model to understand perception and cognition. However, the techniques used to explore psychological phenomena in honey bees have been limited to only a few primary methodologies such as the proboscis extension reflex, sting extension reflex, and free flying target discrimination-tasks. Methods to explore operant conditioning in bees and other invertebrates are not as varied as with vertebrates. This may be due to the availability of a suitable response requirement. In this manuscript we offer a new method to explore operant conditioning in honey bees: the cap pushing response (CPR). We used the CPR to test for difference in learning curves between novel auto-shaping and more traditional explicit-shaping. The CPR protocol requires bees to exhibit a novel behavior by pushing a cap to uncover a food source. Using the CPR protocol we tested the effects of both explicit-shaping and auto-shaping techniques on operant conditioning. The goodness of fit and lack of fit of these data to the Rescorla-Wagner learning-curve model, widely used in classical conditioning studies, was tested. The model fit well to both control and explicit-shaping results, but only for a limited number of trials. Learning ceased rather than continuing to asymptotically approach the physiological most accurate possible. Rate of learning differed between shaped and control bee treatments. Learning rate was about 3 times faster for shaped bees, but for all measures of proficiency control and shaped bees reached the same level. Auto-shaped bees showed one-trial learning rather than the asymptotic approach to a maximal efficiency. However, in terms of return-time, the auto-shaped bees’ learning did not carry over to the covered-well test treatments. PMID:27626797

  14. Operant Conditioning in Honey Bees (Apis mellifera L.): The Cap Pushing Response.

    Science.gov (United States)

    Abramson, Charles I; Dinges, Christopher W; Wells, Harrington

    2016-01-01

    The honey bee has been an important model organism for studying learning and memory. More recently, the honey bee has become a valuable model to understand perception and cognition. However, the techniques used to explore psychological phenomena in honey bees have been limited to only a few primary methodologies such as the proboscis extension reflex, sting extension reflex, and free flying target discrimination-tasks. Methods to explore operant conditioning in bees and other invertebrates are not as varied as with vertebrates. This may be due to the availability of a suitable response requirement. In this manuscript we offer a new method to explore operant conditioning in honey bees: the cap pushing response (CPR). We used the CPR to test for difference in learning curves between novel auto-shaping and more traditional explicit-shaping. The CPR protocol requires bees to exhibit a novel behavior by pushing a cap to uncover a food source. Using the CPR protocol we tested the effects of both explicit-shaping and auto-shaping techniques on operant conditioning. The goodness of fit and lack of fit of these data to the Rescorla-Wagner learning-curve model, widely used in classical conditioning studies, was tested. The model fit well to both control and explicit-shaping results, but only for a limited number of trials. Learning ceased rather than continuing to asymptotically approach the physiological most accurate possible. Rate of learning differed between shaped and control bee treatments. Learning rate was about 3 times faster for shaped bees, but for all measures of proficiency control and shaped bees reached the same level. Auto-shaped bees showed one-trial learning rather than the asymptotic approach to a maximal efficiency. However, in terms of return-time, the auto-shaped bees' learning did not carry over to the covered-well test treatments.

  15. Application-Ready Expedited MODIS Data for Operational Land Surface Monitoring of Vegetation Condition

    Directory of Open Access Journals (Sweden)

    Jesslyn F. Brown

    2015-12-01

    Full Text Available Monitoring systems benefit from high temporal frequency image data collected from the Moderate Resolution Imaging Spectroradiometer (MODIS system. Because of near-daily global coverage, MODIS data are beneficial to applications that require timely information about vegetation condition related to drought, flooding, or fire danger. Rapid satellite data streams in operational applications have clear benefits for monitoring vegetation, especially when information can be delivered as fast as changing surface conditions. An “expedited” processing system called “eMODIS” operated by the U.S. Geological Survey provides rapid MODIS surface reflectance data to operational applications in less than 24 h offering tailored, consistently-processed information products that complement standard MODIS products. We assessed eMODIS quality and consistency by comparing to standard MODIS data. Only land data with known high quality were analyzed in a central U.S. study area. When compared to standard MODIS (MOD/MYD09Q1, the eMODIS Normalized Difference Vegetation Index (NDVI maintained a strong, significant relationship to standard MODIS NDVI, whether from morning (Terra or afternoon (Aqua orbits. The Aqua eMODIS data were more prone to noise than the Terra data, likely due to differences in the internal cloud mask used in MOD/MYD09Q1 or compositing rules. Post-processing temporal smoothing decreased noise in eMODIS data.

  16. Experimental investigations on a common centrifugal pump operating under gas entrainment conditions

    Energy Technology Data Exchange (ETDEWEB)

    Schäfer, Thomas, E-mail: thomas.schaefer@hzdr.de [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Fluid Dynamics (Germany); Neumann, Martin [Technische Universität Dresden, AREVA Endowed Chair of Imaging Techniques in Energy and Process Engineering (Germany); Bieberle, André [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Fluid Dynamics (Germany); Hampel, Uwe [Helmholtz-Zentrum Dresden-Rossendorf, Institute of Fluid Dynamics (Germany); Technische Universität Dresden, AREVA Endowed Chair of Imaging Techniques in Energy and Process Engineering (Germany)

    2017-05-15

    Highlights: • The pump performance has been evaluated for several gas entrainment conditions. • The gas entraining flow regime has a large impact on the pump performance. • High-resolution gamma-ray computed tomography (HireCT) has been applied. • Gas holdup inside the operating impeller has been visualized and quantified. • Gas holdup profiles along selected streamlines have been calculated. - Abstract: This paper presents an experimental study on the effects of additional gas entrainment in centrifugal pumps designed for conveying liquid phases only. The pump performance has been evaluated for several gas entrainment conditions, and for various operational settings of the pump, such as its alignment and the rotational speed of the impeller. As a main performance indicator the impact of entrained gas on the hydraulic power of the pump has been analyzed using experimental data. Additionally, high-resolution gamma-ray computed tomography (HireCT) operated in time-averaged rotation-synchronized scanning mode has been applied to quantify local phase fraction distributions inside the rapidly rotating pump impeller. Based on these quantitative tomographic measurements, gas holdup profiles along selected streamlines have been calculated and gas accumulation areas inside the impeller chambers have been visualized. Thus, various internally accumulated gas holdup patterns have been identified and, eventually, associated with characteristic pump performance behaviors. Moreover, the tomographic measuring method allowed an enhanced gas holdup analysis in specified pump compartments. As a result, the related specific gas and liquid phase holdup profiles have been evaluated.

  17. Transient pressure measurements at part load operating condition of a high head model Francis turbine

    Indian Academy of Sciences (India)

    RAHUL GOYAL; CHIRAG TRIVEDI; B K GANDHI; MICHEL J CERVANTES; OLE G DAHLHAUG

    2016-11-01

    Hydraulic turbines are operating at part load conditions depending on availability of hydraulic energy or to meet the grid requirements. The turbine experiences more fatigue during the part load operating conditions due to flow phenomena such as vortex breakdown in the draft tube and flow instability in the runner.The present paper focuses on the investigation of a high head model Francis turbine operating at 50% load.Pressure measurements have been carried out experimentally on a model Francis turbine. Total six pressure sensors were mounted inside the turbine and other two pressure sensors were mounted at the turbine inlet pipe. It is observed that the turbine experiences significant pressure fluctuations at the vaneless space and the runner.Moreover, a standing wave is observed between the pressure tank outlet and the turbine inlet. Analysis of the data acquired by the pressure sensors mounted in the draft tube showed the presence of vortex breakdown corotating with the runner. The detailed analysis showed the rotating and plunging components of the vortex breakdown. The influence of the rotating component was observed in the entire hydraulic circuit includingdistributor and turbine inlet but not the plunging one.

  18. Numerical analysis of an entire ceramic kiln under actual operating conditions for the energy efficiency improvement.

    Science.gov (United States)

    Milani, Massimo; Montorsi, Luca; Stefani, Matteo; Saponelli, Roberto; Lizzano, Maurizio

    2017-04-05

    The paper focuses on the analysis of an industrial ceramic kiln in order to improve the energy efficiency and thus the fuel consumption and the corresponding carbon dioxide emissions. A lumped and distributed parameter model of the entire system is constructed to simulate the performance of the kiln under actual operating conditions. The model is able to predict accurately the temperature distribution along the different modules of the kiln and the operation of the many natural gas burners employed to provide the required thermal power. Furthermore, the temperature of the tiles is also simulated so that the quality of the final product can be addressed by the modelling. Numerical results are validated against experimental measurements carried out on a real ceramic kiln during regular production operations. The developed numerical model demonstrates to be an efficient tool for the investigation of different design solutions for the kiln's components. In addition, a number of control strategies for the system working conditions can be simulated and compared in order to define the best trade off in terms of fuel consumption and product quality. In particular, the paper analyzes the effect of a new burner type characterized by internal heat recovery capability aimed at improving the energy efficiency of the ceramic kiln. The fuel saving and the relating reduction of carbon dioxide emissions resulted in the order of 10% when compared to the standard burner. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Operational control of radiation conditions in Space Monitoring Data Center of Moscow State University

    Science.gov (United States)

    Kalegaev, Vladimir; Shugay, Yulia; Bobrovnikov, Sergey; Kuznetsov, Nikolay; Barinova, Vera; Myagkova, Irina; Panasyuk, Mikhail

    2016-07-01

    Space Monitoring Data Center (SMDC) of Moscow State University provides mission support for Russian satellites and give operational analysis of radiation conditions in space. SMDC Web-sites (http://smdc.sinp.msu.ru/ and http://swx.sinp.msu.ru/) give access to current data on the level of solar activity, geomagnetic and radiation state of Earth's magnetosphere and heliosphere in near-real time. For data analysis the models of space environment factors working online have been implemented. Interactive services allow one to retrieve and analyze data at a given time moment. Forecasting applications including solar wind parameters, geomagnetic and radiation condition forecasts have been developed. Radiation dose and SEE rate control are of particular importance in practical satellite operation. Satellites are always under the influence of high-energy particle fluxes during their orbital flight. The three main sources of particle fluxes: the Earth's radiation belts, the galactic cosmic rays, and the solar energetic particles (SEP), are taken into account by SMDC operational services to estimate the radiation dose caused by high-energy particles to a satellite at LEO orbits. ISO 15039 and AP8/AE8 physical models are used to estimate effects of galactic cosmic rays and radiation belt particle fluxes. Data of geosynchronous satellites (GOES or Electro-L1) allow to reconstruct the SEP fluxes spectra at a given low Earth orbit taking into account the geomagnetic cut-off depending on geomagnetic activity level.

  20. Tuning the heat transfer medium and operating conditions in magnetic refrigeration

    Science.gov (United States)

    Ghahremani, Mohammadreza; Aslani, Amir; Siddique, Abid; Bennett, Lawrence H.; Della Torre, Edward

    2016-07-01

    A new experimental test bed has been designed, built, and tested to evaluate the effect of the system's parameters on a reciprocating Active Magnetic Regenerator (AMR) near room temperature. Bulk gadolinium was used as the refrigerant, silicon oil as the heat transfer medium, and a magnetic field of 1.3 T was cycled. This study focuses on the methodology of single stage AMR operation conditions to get a high temperature span near room temperature. Herein, the main objective is not to report the absolute maximum attainable temperature span seen in an AMR system, but rather to find the system's optimal operating conditions to reach that maximum span. The results of this research show that there is a optimal operating frequency, heat transfer fluid flow rate, flow duration, and displaced volume ratio in any AMR system. By optimizing these parameters in our AMR apparatus the temperature span between the hot and cold ends increased by 24%. The optimized values are system dependent and need to be determined and measured for any AMR system by following the procedures that are introduced in this research. It is expected that such optimization will permit the design of a more efficient magnetic refrigeration system.

  1. Mathematical model of a plate fin heat exchanger operating under solid oxide fuel cell working conditions

    Science.gov (United States)

    Kaniowski, Robert; Poniewski, Mieczysław

    2013-12-01

    Heat exchangers of different types find application in power systems based on solid oxide fuel cells (SOFC). Compact plate fin heat exchangers are typically found to perfectly fit systems with power output under 5 kWel. Micro-combined heat and power (micro-CHP) units with solid oxide fuel cells can exhibit high electrical and overall efficiencies, exceeding 85%, respectively. These values can be achieved only when high thermal integration of a system is assured. Selection and sizing of heat exchangers play a crucial role and should be done with caution. Moreover, performance of heat exchangers under variable operating conditions can strongly influence efficiency of the complete system. For that reason, it becomes important to develop high fidelity mathematical models allowing evaluation of heat exchangers under modified operating conditions, in high temperature regimes. Prediction of pressure and temperatures drops at the exit of cold and hot sides are important for system-level studies. Paper presents dedicated mathematical model used for evaluation of a plate fin heat exchanger, operating as a part of micro-CHP unit with solid oxide fuel cells.

  2. Analytical solutions for determining extreme water levels in surge tank of hydropower station under combined operating conditions

    Science.gov (United States)

    Wang, Bingbao; Guo, Wencheng; Yang, Jiandong

    2017-06-01

    Combined operating condition usually refers to the control operating condition under which the highest and lowest water levels occur in a surge tank of hydropower station. In this paper, with the basic equations of surge analysis and nonlinear vibrational asymptotic method, analytical expressions of the worst superimposition time of surge waves in an upstream surge tank under four typical combined operating conditions (i.e. load-acceptance-then-rejection, successive load rejection, successive load acceptance and load-rejection-then-acceptance) are derived firstly. Then using these expressions, the analytical extreme water levels are determined. The analytical solutions are verified with numerical simulation results. Finally, the effect of the hydraulic resistance coefficient of surge tank on the control operating condition is investigated. The results indicate that: The analytical solutions for determining extreme water levels in surge tank under various combined operating conditions are accurate due to the good agreements between the analytical results and the numerical results. With the increase of the hydraulic resistance coefficient of surge tank, the control operating condition for the highest water level shifts from load-acceptance-then-rejection condition to successive load rejection condition, and the control operating condition for the lowest water level shifts from load-rejection-then-acceptance condition to successive load acceptance condition.

  3. Assessment of biogas production from MBT waste under different operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Pantini, Sara, E-mail: pantini@ing.uniroma2.it [Department of Civil Engineering and Computer Science Engineering, University of Rome “Tor Vergata”, Via del Politecnico, 1, 00133 Rome (Italy); Verginelli, Iason; Lombardi, Francesco [Department of Civil Engineering and Computer Science Engineering, University of Rome “Tor Vergata”, Via del Politecnico, 1, 00133 Rome (Italy); Scheutz, Charlotte; Kjeldsen, Peter [Department of Environmental Engineering, Technical University of Denmark, Miljoevej, Building 113, DK-2800 Kgs. Lyngby (Denmark)

    2015-09-15

    Highlights: • BMP test displayed high gas potential generation capacity of MBT waste. • Strong inhibition effects were observed due to ammonia and VFA accumulation. • Waste water content was found as the key parameter limiting gas generation. • First order k-values were determined for different operating conditions. - Abstract: In this work, the influence of different operating conditions on the biogas production from mechanically–biologically treated (MBT) wastes is investigated. Specifically, different lab-scale anaerobic tests varying the water content (26–43% w/w up to 75% w/w), the temperature (from 20 to 25 °C up to 55 °C) and the amount of inoculum have been performed on waste samples collected from a full-scale Italian MBT plant. For each test, the gas generation yield and, where applicable, the first-order gas generation rates were determined. Nearly all tests were characterised by a quite long lag-phase. This result was mainly ascribed to the inhibition effects resulting from the high concentrations of volatile fatty acids (VFAs) and ammonia detected in the different stages of the experiments. Furthermore, water content was found as one of the key factor limiting the anaerobic biological process. Indeed, the experimental results showed that when the moisture was lower than 32% w/w, the methanogenic microbial activity was completely inhibited. For the higher water content tested (75% w/w), high values of accumulated gas volume (up to 150 Nl/kgTS) and a relatively short time period to deplete the MBT waste gas generation capacity were observed. At these test conditions, the effect of temperature became evident, leading to gas generation rates of 0.007 d{sup −1} at room temperature that increased to 0.03–0.05 d{sup −1} at 37 °C and to 0.04–0.11 d{sup −1} at 55 °C. Overall, the obtained results highlighted that the operative conditions can drastically affect the gas production from MBT wastes. This suggests that particular caution

  4. Academic medicine amenities unit: developing a model to integrate academic medical care with luxury hotel services.

    Science.gov (United States)

    Kennedy, David W; Kagan, Sarah H; Abramson, Kelly Brennen; Boberick, Cheryl; Kaiser, Larry R

    2009-02-01

    The interface between established values of academic medicine and the trend toward inpatient amenities units requires close examination. Opinions of such units can be polarized, reflecting traditional reservations about the ethical dilemma of offering exclusive services only to an elite patient group. An amenities unit was developed at the University of Pennsylvania Health System in 2007, using an approach that integrated academic medicine values with the benefits of philanthropy and service excellence to make amenities unit services available to all patients. Given inherent internal political concerns, a broadly based steering committee of academic and hospital leadership was developed. An academically appropriate model was conceived, anchored by four principles: (1) integration of academic values, (2) interdisciplinary senior leadership, (3) service excellence, and (4) recalibrated occupancy expectations based on multiple revenue streams. Foremost is ensuring the same health care is afforded all patients throughout the hospital, thereby overcoming ethical challenges and optimizing teaching experiences. Service excellence frames the service ethic for all staff, and this, in addition to luxury hotel-style amenities, differentiates the style and feel of the unit from others in the hospital. Recalibrated occupancy creates program viability given revenue streams redefined to encompass gifts and patient revenue, including both reimbursement and self-pay. The medical-surgical amenities patient-care unit has enjoyed a successful first year and a growing stream of returning patients and admitting physicians. Implications for other academic medical centers include opportunities to extrapolate service excellence throughout the hospital and to cultivate philanthropy to benefit services throughout the medical center.

  5. Fully Electrical Modeling of Thermoelectric Generators with Contact Thermal Resistance Under Different Operating Conditions

    Science.gov (United States)

    Siouane, Saima; Jovanović, Slaviša; Poure, Philippe

    2017-01-01

    The Seebeck effect is used in thermoelectric generators (TEGs) to supply electronic circuits by converting the waste thermal into electrical energy. This generated electrical power is directly proportional to the temperature difference between the TEG module's hot and cold sides. Depending on the applications, TEGs can be used either under constant temperature gradient between heat reservoirs or constant heat flow conditions. Moreover, the generated electrical power of a TEG depends not only on these operating conditions, but also on the contact thermal resistance. The influence of the contact thermal resistance on the generated electrical power have already been extensively reported in the literature. However, as reported in Park et al. (Energy Convers Manag 86:233, 2014) and Montecucco and Knox (IEEE Trans Power Electron 30:828, 2015), while designing TEG-powered circuit and systems, a TEG module is mostly modeled with a Thévenin equivalent circuit whose resistance is constant and voltage proportional to the temperature gradient applied to the TEG's terminals. This widely used simplified electrical TEG model is inaccurate and not suitable under constant heat flow conditions or when the contact thermal resistance is considered. Moreover, it does not provide realistic behaviour corresponding to the physical phenomena taking place in a TEG. Therefore, from the circuit designer's point of view, faithful and fully electrical TEG models under different operating conditions are needed. Such models are mainly necessary to design and evaluate the power conditioning electronic stages and the maximum power point tracking algorithms of a TEG power supply. In this study, these fully electrical models with the contact thermal resistance taken into account are presented and the analytical expressions of the Thévenin equivalent circuit parameters are provided.

  6. Fully Electrical Modeling of Thermoelectric Generators with Contact Thermal Resistance Under Different Operating Conditions

    Science.gov (United States)

    Siouane, Saima; Jovanović, Slaviša; Poure, Philippe

    2016-09-01

    The Seebeck effect is used in thermoelectric generators (TEGs) to supply electronic circuits by converting the waste thermal into electrical energy. This generated electrical power is directly proportional to the temperature difference between the TEG module's hot and cold sides. Depending on the applications, TEGs can be used either under constant temperature gradient between heat reservoirs or constant heat flow conditions. Moreover, the generated electrical power of a TEG depends not only on these operating conditions, but also on the contact thermal resistance. The influence of the contact thermal resistance on the generated electrical power have already been extensively reported in the literature. However, as reported in Park et al. (Energy Convers Manag 86:233, 2014) and Montecucco and Knox (IEEE Trans Power Electron 30:828, 2015), while designing TEG-powered circuit and systems, a TEG module is mostly modeled with a Thévenin equivalent circuit whose resistance is constant and voltage proportional to the temperature gradient applied to the TEG's terminals. This widely used simplified electrical TEG model is inaccurate and not suitable under constant heat flow conditions or when the contact thermal resistance is considered. Moreover, it does not provide realistic behaviour corresponding to the physical phenomena taking place in a TEG. Therefore, from the circuit designer's point of view, faithful and fully electrical TEG models under different operating conditions are needed. Such models are mainly necessary to design and evaluate the power conditioning electronic stages and the maximum power point tracking algorithms of a TEG power supply. In this study, these fully electrical models with the contact thermal resistance taken into account are presented and the analytical expressions of the Thévenin equivalent circuit parameters are provided.

  7. Tip clearance noise of axial flow fans operating at design and off-design condition

    Science.gov (United States)

    Fukano, T.; Jang, C.-M.

    2004-08-01

    The noise due to tip clearance (TC) flow in axial flow fans operating at a design and off-design conditions is analyzed by an experimental measurement using two hot-wire probes rotating with the fan blades. The unsteady nature of the spectra of the real-time velocities measured by two hot-wire sensors in a vortical flow region is investigated by using cross-correlation coefficient and retarded time of the two fluctuating velocities. The results show that the noise due to TC flow consists of a discrete frequency noise due to periodic velocity fluctuation and a broadband noise due to velocity fluctuation in the blade passage. The peak frequencies in a vortical flow are mainly observed below at four harmonic blade passing frequency. The discrete frequency component of velocity fluctuation at the off-design operating conditions is generated in vortical flow region as well as in reverse flow region. The peak frequency can be an important noise source when the fans are rotated with a high rotational speed. The authors propose a spiral pattern of velocity fluctuation in the vortical flow to describe the generation mechanism of the peak frequency in the vortical flow. In addition, noise increase due to TC flow at low flow rate condition is analyzed with relation to the distribution of velocity fluctuation due to the interference between the tip leakage vortex and the adjacent pressure surface of the blade.

  8. Performance analysis of monary and binary geothermal power plants operation for Ukraine conditions

    Directory of Open Access Journals (Sweden)

    Аlla Е. Denysova

    2015-03-01

    Full Text Available Every day the shortage in natural gas and coal does increase. In this respect, a great attention is paid to alternative energy sources, and geothermal electrical power generation represents one of the most cost-effective technologies. New power generation technologies using geothermal resources are ecologically clean and are close approaching to traditional ones from the efficiency point of view. This research aim is to analyze the efficiency of monary and binary geothermal power plants operation under actual conditions in Ukraine. Authors discuss prospects for the geothermal power engineering development in Ukraine and other countries. The principal thermal diagrams of monary and binary power plants are represented, as well as their operational principle considering these schemes advantages and disadvantages. Effected is an analysis of such stations performances under conditions of Ukraine. This research value and practical significance are related to the fact that for Ukraine both monary and binary geothermal power plants are very promising, but each engineering solutions should strictly follow its specific functional conditions.

  9. AUTOMATED SYSTEM OF OPERATIONAL CONTROL HEATING AND AIR CONDITIONING OF BUILDINGS

    Directory of Open Access Journals (Sweden)

    PETRENKO A. O.

    2016-08-01

    Full Text Available Statement of the problem. Health and human performance largely determined by the conditions of climate and air quality in residential, administrative and residential and public buildings. At that, in turn, is influenced by the external environment and the climate, and the geometric dimensions of the room, and thermal performance building envelopes, and the location of the premises (Orientation, and many other factors. The result is the formation of complex systems, which control decision-making in conditions of multifactor [1]. In hygienic purposes it is necessary to strive to create the best indoor microclimate conditions, regardless of changes in the factors that affect the climate in residential, administrative and residential and public buildings. Develop systems to ensure the necessary microclimate parameters – it is a complex and important task, which will depend entirely comfortable and cozy environment for the person. The problem of the present time, there is a steady increase in the energy consumption of these systems, due to the rise in price of non-renewable energy sources, and our job is, to simulate the work of software systems necessary microclimate for the changes in the factors that affect it and to minimize the use of non-renewable energy sources. Analysis of recent research and publications. Domestic and foreign hygienists [2, 3, 4] to establish a connection between the climate in the room and in the workplace and the state of human health. Formation of the indoor climate of residential, administrative and residential and public buildings is influenced by many factors that have already noted earlier [5, 6]. Study of the processes of influence of various factors on human health is of great complexity. If we consider each process separately, and in this case they are not currently amenable to theoretical description clearer. To simulate the effect of these factors studies were conducted, which showed that, with sufficient

  10. Enhanced Operation of Electricity Distribution Grids Through Smart Metering PLC Network Monitoring, Analysis and Grid Conditioning

    Directory of Open Access Journals (Sweden)

    Iker Urrutia

    2013-01-01

    Full Text Available Low Voltage (LV electricity distribution grid operations can be improved through a combination of new smart metering systems’ capabilities based on real time Power Line Communications (PLC and LV grid topology mapping. This paper presents two novel contributions. The first one is a new methodology developed for smart metering PLC network monitoring and analysis. It can be used to obtain relevant information from the grid, thus adding value to existing smart metering deployments and facilitating utility operational activities. A second contribution describes grid conditioning used to obtain LV feeder and phase identification of all connected smart electric meters. Real time availability of such information may help utilities with grid planning, fault location and a more accurate point of supply management.

  11. Operational conditions for successful partial nitrification in a sequencing batch reactor (SBR) based on process kinetics.

    Science.gov (United States)

    Liu, Xiaoguang; Kim, Mingu; Nakhla, George

    2017-03-01

    The objective of this study is to analyze the factors affecting the performance of partial nitrification in a sequencing batch reactor (SBR) using kinetic models. During the 4-month operation, dissolved oxygen (DO) and influent ammonia concentration were selected as operating variables to evaluate nitrite accumulation. Stable partial nitrification was observed with two conditions, influent ammonia concentration of 190 mg N/L and a DO of 0.6-3.0 mg/L as well as influent ammonia concentration of 100 mg N/L and a DO of 0.15-2.0 mg/L with intermittent aeration. At a DO of 0.6-3.0 mg O2/L and influent ammonia concentration of 90 mg N/L, nitrite-oxidizing bacteria growth was not suppressed. Kinetic parameters were determined or estimated with batch tests and model simulation. The kinetic model predicted the SBR performance well.

  12. Equiconvergence of spectral decompositions of 1D Dirac operators with regular boundary conditions

    CERN Document Server

    Djakov, Plamen

    2011-01-01

    One dimensional Dirac operators $$ L_{bc}(v) y = i 1 & 0 0 & -1 \\frac{dy}{dx} + v(x) y, \\quad y = y_1 y_2, \\quad x\\in[0,\\pi]$$, considered with $L^2$-potentials $ v(x) = 0 & P(x) Q(x) & 0$ and subject to regular boundary conditions ($bc$), have discrete spectrum. For strictly regular $bc,$ the spectrum of the free operator $ L_{bc}(0) $ is simple while the spectrum of $ L_{bc}(v) $ is eventually simple, and the corresponding normalized root function systems are Riesz bases. For expansions of functions of bounded variation about these Riesz bases, we prove the uniform equiconvergence property and point-wise convergence on the closed interval $[0,\\pi].$ Analogous results are obtained for regular but not strictly regular $bc.$

  13. High-Density Fiber Optical Sensor and Instrumentation for Gas Turbine Operation Condition Monitoring

    Directory of Open Access Journals (Sweden)

    Hua Xia

    2013-01-01

    Full Text Available Gas turbine operation control is normally based on thermocouple-measured exhaust temperatures. Due to radiation shielding and bulky package, it is difficult to provide high spatial resolution for measuring can-to-can combustion temperature profile at the exhaust duct. This paper has demonstrated that wavelength-division-multiplexing-based fiber Bragg grating sensors could provide high spatial resolution steady and dynamic temperature measurements. A robust sensor package can be designed with either circumferential sensing cable or radial sensing rake for quasi-distributing multiple fiber sensors in the gas turbine environment. The field validations have demonstrated that quasi-distributed fiber sensors have not only demonstrated its temperature measurement accuracy compared to existing thermocouple sensors but also shown its unique dynamic response amplitude and power spectra that could be utilized for gas turbine transient operation condition monitoring and diagnostics.

  14. LHC Beam Dump Design Study - Part III : Off-normal operating conditions

    CERN Document Server

    Bruno, L; Ross, M; Sala, P

    2000-01-01

    The LHC beam dump design study has been preliminarily substantiated by energy deposition simulations (Part I) and heat transfer analyses (Part II). The present report is devoted to the abnormal operating conditions induced by a malfunction of the beam diluters. A general approach to the analysis of off-normal operation is presented, which is derived from standard design norms adopted in the nuclear industry. Attention is focused mainly on the carbon core, which is longitudinally split into segments of different density in order to better distribute the deposited energy. The maximum energy density it absorbs decreases by at least 33%, compared to a uniform standard density carbon core. This structure may sustain any partial sweep failure without major damage, up to the ultimate beam intensity and energy. To minimise the risks inherent in a fully unswept beam, a sacrificial graphite mandrel will be placed on the core axis, surrounded by a thick high strength carbon-carbon composite tube. With this arrangement, ...

  15. The 4-D descent trajectory generation techniques under realistic operating conditions

    Science.gov (United States)

    Williams, David H.; Knox, Charles E.

    1990-01-01

    NASA-Langley has been conducting and sponsoring research in airborne energy management for a number of years. During the course of this research, two fundamental techniques for the generation of 4D (fixed time) descent trajectories have emerged as viable candidates for advanced flight management systems. The first technique utilizes speed schedules of constant Mach number transitioning to constant calibrated airspeed chosen empirically to produce minimum fuel usage. The second technique computes cost optimized speed schedules of variable airspeed developed through application of optimal control theory. Both techniques have been found to produce reasonable and flyable descent trajectories. The formulation of the algorithms for each technique is evaluated and their suitability for operations in realistic conditions is discussed. Operational factors considered include: airplace speed, thrust, and altitude rate constaints; wind, temperature, and pressure variations; Air Traffic Control altitude, speed, and time constaints; and pilot interface and guidance considerations. Time flexibility, fuel usage, and airborne computational requirements were the primary performance measures.

  16. [Effect of injection of enkephalin and bestatin in caudate-putamen on operant conditioning in rats].

    Science.gov (United States)

    Zhang, S Y; Zhang, Y P; Zhang, M L; Qi, H X; Wang, B

    1992-10-01

    Female Wistar rats were trained in a Skinner-box, 30 trials per day in a dark room to establish operant defence conditioning. Training started with a light (15 s), then combined with footshock for further 8 s. When the rats learned to press the key to avoid footshock within 15 s, conditioned response was considered established. After the rats reached a conditioning rate (CR) above 80% for 5 days, cannulae were implanted into caudate-putamen. Two to three days later, Met-enkephalin (MEK) or bestatin (an aminopeptidase inhibitor) was injected bilaterally into caudate-putamen. 30 min, 2 h, 24 h and 48 h after injection, conditioning tests were conducted, with each session consisting of 30 trials. Control experiments were done when 0.9% NaCl (NS) was injected. After injection of NS, CR maintained above 80% in all 4 test sessions. MEK (60 ng/rat) or bestatin (10 micrograms/rat) significantly lowered the CR during the 30 min and 2 h test session. In the latter case, the latency (L) was also prolonged. However both CR and L returned to the control level in the 24 h and 48 h test sessions. Naloxone (2 mg/kg, i.p.) blocked the conditioning-depression effect of bestatin. No significant alteration was seen in locomotor activity after MEK or bestatin injection. The results suggest that enkephalin in caudate-putamen may be involved in the regulation of retrieval of conditioning. Bestatin mimics the effect of MEK on conditioning reflex probably by increasing production of endogenous enkephalin.

  17. Effects of operating conditions on the adhesive strength of Pseudomonas fluorescens biofilms in tubes.

    Science.gov (United States)

    Chen, M J; Zhang, Z; Bott, T R

    2005-06-25

    Understanding the mechanical properties of biofilms, especially the force required to disrupt them and remove them from substrata is very important to development of antibiofouling strategies. In this work, a novel micromanipulation technique with a specially designed T-shaped probe has been developed to serve as an experimental means to measure directly the adhesive strength of biofouling deposits on the surface of a glass test stud. The basic principle of this novel technique is to pull away a whole biofilm accumulated on the surface of a glass test stud with T-shaped probe, and to measure simultaneously the force imposed on the biofilm. The adhesive strength between the biofilms and the surface to which they are attached, is defined as the work per unit area required to remove the biofilms from the surface. The biofouling experiments were performed on an elaborate design of a simulated heat exchanger system. A monoculture of Pseudomonas fluorescens was chosen as the fouling microorganism for the laboratory studies. Results indicate that the adhesive strength of the biofilm was affected by the conditions of operation, such as biofilm age, nutrient concentration, suspended cell concentration, pH, surface roughness of the substratum and fluid velocity. As noted, the effect of fluid velocity on the biofilm adhesive strength seemed to overwhelm other factors. At the same operating conditions, the biofilm adhesive strength increased as the fluid velocity increased within the range of 0.6-1.6m/s. In addition, the flow-related biofilm structures were observed that biofilms generally grew as a more compact pattern at the higher fluid velocity. Apparently, the fluid velocity can affect the biofilm structure, which in turn determines the biofilm adhesive strength. The knowledge of the biofilm adhesive strength with associated influences of the operating conditions may be used to define better cleaning procedures.

  18. Safe operating conditions for NSLS-II Storage Ring Frontends commissioning

    Energy Technology Data Exchange (ETDEWEB)

    Seletskiy, S. [Brookhaven National Lab. (BNL), Upton, NY (United States); Amundsen, C. [Brookhaven National Lab. (BNL), Upton, NY (United States); Ha, K. [Brookhaven National Lab. (BNL), Upton, NY (United States); Hussein, A. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2015-04-02

    The NSLS-II Storage Ring Frontends are designed to safely accept the synchrotron radiation fan produced by respective insertion device when the electron beam orbit through the ID is locked inside the predefined Active Interlock Envelope. The Active Interlock is getting enabled at a particular beam current known as AI safe current limit. Below such current the beam orbit can be anywhere within the limits of the SR beam acceptance. During the FE commissioning the beam orbit is getting intentionally disturbed in the particular ID. In this paper we explore safe operating conditions for the Frontends commissioning.

  19. Atmospheric conditions affecting seeing at St. Catherine: Estimation of operational time for NRIAG new telescope

    Science.gov (United States)

    Mekhaimr, Sayed A.

    2017-06-01

    The study of the prevailing atmospheric conditions is an essential part of any site testing for a new telescope establishment. In this article, the meteorological parameters that affect the astronomical seeing at St. Catherine region, where a two candidate sites are located, are studied based on the available climate data. The complex topographical features of the region cause some differences between the weather at the nearest meteorological station and that at the candidate sites. This issue is illustrated through high resolution atmospheric modeling for short period (six days) as a case study. Finally, a preliminary estimation of operational hours for the telescope at the candidate sites is calculated.

  20. The effect of operational conditions on the sludge specific methanogenic activity and sludge biodegradability

    Energy Technology Data Exchange (ETDEWEB)

    Leitao, R. C.; Santaella, S. T.; Haandel, A. C. van; Zeeman, G.; Lettinga, G.

    2009-07-01

    The Specific Methanogenic Activity (SMA) and sludge biodegradability of an anaerobic sludge depends on various operational and environmental conditions imposed to the anaerobic reactor. However, the effects of hydraulic retention time (HRT), influent COD concentration (COD{sub i}nf) and sludge retention time (SRT) on those two parameters need to be elucidated. This knowledge about SMA can provide insights about the capacity of the UASB reactors to withstand organic and hydraulic shock loads, whereas the biodegradability gives information necessary for final disposal of the sludge. (Author)

  1. Lithium-ion battery dynamic model for wide range of operating conditions

    DEFF Research Database (Denmark)

    Stroe, Ana-Irina; Stroe, Daniel-Ioan; Swierczynski, Maciej Jozef

    2017-01-01

    In order to analyze the dynamic behavior of a Lithium-ion (Li-ion) battery and to determine their suitability for various applications, battery models are needed. An equivalent electrical circuit model is the most common way of representing the behavior of a Li-ion battery. There are different...... characterization tests performed for a wide range of operating conditions (temperature, load current and state-ofcharge) on a commercial available 13Ah high-power lithium titanate oxide battery cell. The obtained results were used to parametrize the proposed dynamic model of the battery cell. To assess...

  2. Using operant conditioning and desensitization to facilitate veterinary care with captive reptiles.

    Science.gov (United States)

    Hellmuth, Heidi; Augustine, Lauren; Watkins, Barbara; Hope, Katharine

    2012-09-01

    In addition to being a large component of most zoological collections, reptile species are becoming more popular as family pets. Reptiles have the cognitive ability to be trained to facilitate daily husbandry and veterinary care. Desensitization and operant conditioning can alleviate some of the behavioral and physiological challenges of treating these species. A survey of reptile training programs at zoos in the United States and worldwide reveals that there are many successful training programs to facilitate veterinary care and minimize stress to the animal. Many of the techniques being used to train reptiles in zoological settings are transferable to the exotic pet clinician.

  3. Effect of magnetic field on the behavior of operantly conditioned mice

    Energy Technology Data Exchange (ETDEWEB)

    Brannon, T..; Williams, M.C.; Ward, S.

    1988-01-01

    Two mice were trained to run a T-shaped maze. One mouse was trained to turn right while the other mouse was trained to turn left. A magnetic field was then set up in the arm of the maze to which the mouse had been trained to turn. The mice were allowed to run the maze and scored on the basis of their correct response. The scores of both mice were significantly lower when the magnetic field was present, thus indicating interference by the magnetic field on their operant conditioning.

  4. Optimization of Design Parameters and Operating Conditions of Electrochemical Capacitors for High Energy and Power Performance

    Science.gov (United States)

    Ike, Innocent S.; Sigalas, Iakovos; Iyuke, Sunny E.

    2017-03-01

    Theoretical expressions for performance parameters of different electrochemical capacitors (ECs) have been optimized by solving them using MATLAB scripts as well as via the MATLAB R2014a optimization toolbox. The performance of the different kinds of ECs under given conditions was compared using theoretical equations and simulations of various models based on the conditions of device components, using optimal values for the coefficient associated with the battery-kind material ( K BMopt) and the constant associated with the electrolyte material ( K Eopt), as well as our symmetric electric double-layer capacitor (EDLC) experimental data. Estimation of performance parameters was possible based on values for the mass ratio of electrodes, operating potential range ratio, and specific capacitance of electrolyte. The performance of asymmetric ECs with suitable electrode mass and operating potential range ratios using aqueous or organic electrolyte at appropriate operating potential range and specific capacitance was 2.2 and 5.56 times greater, respectively, than for the symmetric EDLC and asymmetric EC using the same aqueous electrolyte, respectively. This enhancement was accompanied by reduced cell mass and volume. Also, the storable and deliverable energies of the asymmetric EC with suitable electrode mass and operating potential range ratios using the proper organic electrolyte were 12.9 times greater than those of the symmetric EDLC using aqueous electrolyte, again with reduced cell mass and volume. The storable energy, energy density, and power density of the asymmetric EDLC with suitable electrode mass and operating potential range ratios using the proper organic electrolyte were 5.56 times higher than for a similar symmetric EDLC using aqueous electrolyte, with cell mass and volume reduced by a factor of 1.77. Also, the asymmetric EDLC with the same type of electrode and suitable electrode mass ratio, working potential range ratio, and proper organic electrolyte

  5. Operating conditions and stability of spin torque majority gates: Analytical understanding and numerical evidence

    Science.gov (United States)

    Vaysset, Adrien; Manfrini, Mauricio; Nikonov, Dmitri E.; Manipatruni, Sasikanth; Young, Ian A.; Radu, Iuliana P.; Thean, Aaron

    2017-01-01

    The functionality of a cross-shaped Spin Torque Majority Gate (STMG) is primarily limited by the pinning of a domain wall (DW) at the center of the device. Here, an analytical model is built to calculate the conditions for such a pinning and to deduce the operating range. The assumptions of the model and the conclusions are validated by micromagnetic simulations. The total magnetic energy of the DW state is derived. By minimizing this energy with respect to two degrees of freedom, the DW stability condition is obtained. We find that the lateral length of the STMG is the critical dimension: it must be smaller than about five times the DW width. This result is confirmed by micromagnetic simulations with a high accuracy. In process, we solved a more fundamental problem: the macrospin limit of a finite ferromagnet containing one pinning site. We found the correction of the usual DW width expression due to finite length of wires.

  6. Key Parameters for Operator Diagnosis of BWR Plant Condition during a Severe Accident

    Energy Technology Data Exchange (ETDEWEB)

    Clayton, Dwight A [ORNL; Poore III, Willis P [ORNL

    2015-01-01

    The objective of this research is to examine the key information needed from nuclear power plant instrumentation to guide severe accident management and mitigation for boiling water reactor (BWR) designs (specifically, a BWR/4-Mark I), estimate environmental conditions that the instrumentation will experience during a severe accident, and identify potential gaps in existing instrumentation that may require further research and development. This report notes the key parameters that instrumentation needs to measure to help operators respond to severe accidents. A follow-up report will assess severe accident environmental conditions as estimated by severe accident simulation model analysis for a specific US BWR/4-Mark I plant for those instrumentation systems considered most important for accident management purposes.

  7. Adaptive strategies of remote systems operators exposed to perturbed camera-viewing conditions

    Science.gov (United States)

    Stuart, Mark A.; Manahan, Meera K.; Bierschwale, John M.; Sampaio, Carlos E.; Legendre, A. J.

    1991-01-01

    This report describes a preliminary investigation of the use of perturbed visual feedback during the performance of simulated space-based remote manipulation tasks. The primary objective of this NASA evaluation was to determine to what extent operators exhibit adaptive strategies which allow them to perform these specific types of remote manipulation tasks more efficiently while exposed to perturbed visual feedback. A secondary objective of this evaluation was to establish a set of preliminary guidelines for enhancing remote manipulation performance and reducing the adverse effects. These objectives were accomplished by studying the remote manipulator performance of test subjects exposed to various perturbed camera-viewing conditions while performing a simulated space-based remote manipulation task. Statistical analysis of performance and subjective data revealed that remote manipulation performance was adversely affected by the use of perturbed visual feedback and performance tended to improve with successive trials in most perturbed viewing conditions.

  8. Determination of materials and cutting conditions in a CNC lathe turning operation

    Directory of Open Access Journals (Sweden)

    Juan Bautista Hernández-Granados

    2014-05-01

    Full Text Available One of the main problems of machining can be described as the achievement of a predefined product quality with given working conditions. The turning operation on Sistemas Integrados de Manufactura (SIMTEC Laboratory has been stu-died with diffe-rent cutting conditions (feed, depth of cut, rpm and material type (Aluminum 6061, Steel 1020 to identify the combination and level factors that improve the surface roughness in a work piece. Using three of Design of Experiments techniques (DOE, such as factorial design, multiple linear regression and response surface methodo-logy (RSM we identified the factors and levels that reduce the surface roughness and these are the feed rate = 50 mm/min, rpm = 1200 and aluminum material. A first-order model has been established between the cutting parameters and surface roughness which can be used together with the RMS graph to predict an average roughness value.

  9. Experimental Evaluation of the Surface Alteration of Gasket Samples under Operative Conditions

    Directory of Open Access Journals (Sweden)

    M.C. Bignozzi

    2015-12-01

    Full Text Available This paper investigates the surface alteration of gasket samples commercialized by two alternative producers. These gaskets, in polymeric materials, are installed in process plants used for cleaning tires molds by a pioneering ultrasonic process. They are exposed to a combination of ultrasonic waves, temperature, humidity and acid attack causing several erosion phenomena. Their surface degradation under ordinary operative conditions was investigated using mechanical and tribological tests. The experimental characterization was performed by optical microscopy, scanning electron microscopy, thermograms, differential scanning calorimetry curves and infrared spectra aiming at defining the specific mechanics of wearing. As a conclusion, it was possible to state that even if samples exhibit similar chemical structures, their thermal and mechanical properties as well as their geometric dimensions are different. Such differences in the materials might cause various unexpected wear behaviors when gaskets are employed in the same working conditions.


  10. A Weekly Indicator of Surface Moisture Status from Satellite Data for Operational Monitoring of Crop Conditions

    Directory of Open Access Journals (Sweden)

    Francesco Nutini

    2017-06-01

    Full Text Available The triangle method has been applied to derive a weekly indicator of evaporative fraction on vegetated areas in a temperate region in Northern Italy. Daily MODIS Aqua Land Surface Temperature (MYD11A1 data has been combined with air temperature maps and 8-day composite MODIS NDVI (MOD13Q1/MYD13Q1 data to estimate the Evaporative Fraction (EF at 1 km resolution, on a daily basis. Measurements at two eddy covariance towers located within the study area have been exploited to assess the reliability of satellite based EF estimations as well as the robustness of input data. Weekly syntheses of the daily EF indicator (EFw were then derived at regional scale for the years 2010, 2011 and 2012 as a proxy of overall surface moisture condition. EFw showed a temporal behavior consistent with growing cycles and agro-practices of the main crops cultivated in the study area (rice, forages and corn. Comparison with official regional corn yield data showed that variations in EFw cumulated over summer are related with crop production shortages induced by water scarcity. These results suggest that weekly-averaged EF estimated from MODIS data is sensible to water stress conditions and can be used as an indicator of crops’ moisture conditions at agronomical district level. Advantages and disadvantages of the proposed approach to provide information useful to issue operational near real time bulletins on crop conditions at regional scale are discussed.

  11. Differential rearing conditions and alcohol-preferring rats: consumption of and operant responding for ethanol.

    Science.gov (United States)

    Deehan, Gerald A; Palmatier, Matthew I; Cain, Mary E; Kiefer, Stephen W

    2011-04-01

    Exposing rats to differential rearing conditions during early postweaning development has been shown to produce changes in a number of behaviors displayed during adulthood. The purpose of the present studies was to investigate whether rearing alcohol-preferring (P) and nonpreferring (NP) rats in an environmental enrichment condition (EC), a social condition (SC), or an impoverished condition (IC) would differentially affect self-administration of 10% ethanol. In Experiment 1, rats were tested for consumption of 10% ethanol in limited- and free-access tests. For Experiment 2, rats were trained to respond in an operant chamber for ethanol and then provided concurrent access to 10% ethanol and water. Each solution was presented in a separate liquid dipper after meeting the schedule of reinforcement on distinct levers. After concurrent access tests, the water lever/dipper was inactivated and a progressive ratio (PR) schedule was initiated. Three successive solutions (10% ethanol, 15% ethanol, and 10% sucrose) were tested under the PR. For P rats, rearing in an EC reduced ethanol consumption, preference, and motivation to obtain ethanol, relative to P rats reared in an IC. Thus, exposure to a novel environment immediately after weaning acted to decrease the reinforcing properties of ethanol in an animal model for alcoholism.

  12. Slide Valves for Single-Screw Expanders Working Under Varied Operating Conditions

    Directory of Open Access Journals (Sweden)

    Yuting Wu

    2016-06-01

    Full Text Available This paper fully describes the working principle of slide valves in single-screw expanders (SSEs. A geometric analysis of suction and volume ratio slide valves is presented to determine the relations between volume ratio, suction closure volume, discharge opening volume and slide valves displacement. An organic Rankine cycle (ORC thermodynamic model with SSE integrated with slide valves is developed to analyze the power output of SSE and the net power output of ORC system and variation law of slide valves displacement. Analysis of a typical ORC system under changing operating conditions shows that the power output of the expander and the net output power of the ORC system with slide valves are much better than those without slide valves. When the condensing temperature is 40 °C and the waste availability is 80 kW, the increase in output power and net output power are approximately 3.4 kW and 5 kW, respectively. The presented geometric analysis of slide valves and the thermodynamic model integrated with slide valves can be used to provide a theoretical and technical basis for designing the slide valves of SSEs and the control strategies of slide valves under varied operating conditions.

  13. Effects of operating conditions on THMs and HAAs formation during wastewater chlorination

    Energy Technology Data Exchange (ETDEWEB)

    Sun Yingxue; Wu Qianyuan [Environmental Simulation and Pollution Control State Key Joint Laboratory, Department of Environmental Science and Engineering, Tsinghua University, Beijing 100084 (China); Hu Hongying, E-mail: hyhu@tsinghua.edu.cn [Environmental Simulation and Pollution Control State Key Joint Laboratory, Department of Environmental Science and Engineering, Tsinghua University, Beijing 100084 (China); Tian Jie [Environmental Simulation and Pollution Control State Key Joint Laboratory, Department of Environmental Science and Engineering, Tsinghua University, Beijing 100084 (China)

    2009-09-15

    Disinfection is the last barrier of wastewater reclamation process to protect ecosystem safety and human health. However, the chlorination process results in the formation of mutagenic/carcinogenic disinfection by-products (DBPs) deriving from the reaction of the chlorine with organic compounds in wastewater. The effects of operating conditions (chlorine dose, contact time, reaction temperature and pH value) of chlorination on the formation of trihalomethanes (THMs) and haloacetic acids (HAAs) in biologically treated wastewater samples were investigated in this study. The results indicated that the total THMs (TTHM) and total HAAs (THAA) increased exponentially with increasing chlorine dose, but there are discrepancies between the formation rates of TTHM and THAA. The THAA reached a peak at contact time of 2 h and thereafter decreased with extended time. The formation time of THMs depends on the wastewater content of quick or slow formers. The yields of bromated HAAs (as MBAA, BCAA, and BDCAA) would decrease markedly after the contact time over 2 h during wastewater chlorination, and were favored in low pH values of 4 and high pH values of 9 under certain contact time. In addition, the formation of MBAA, BCAA, BDCAA decreased gradually as reaction temperature increased from 4 to 30 deg. C in the chlorination of wastewater containing a certain concentration of bromide. The effects of operating conditions on THMs and HAAs formation during wastewater chlorination were completely different from those of surface water disinfection.

  14. Review of Operational Challenges and Changing Conditions associated with Offshore Submerged Vertical Pumping Station

    Science.gov (United States)

    Samsudin, M. L.; Munisamy, K. M.; Thangaraju, S. K.

    2015-09-01

    Cooling water system is one of the essential auxiliary systems for a power generating plant. The decision to have an offshore pumping station, instead of onshore station, may have been driven by the scarcity in land area or for direct water supply access. However, the design has several disadvantages such as tendency for sediment intakes, limited condition monitoring activities and inaccessible sump for maintenance and modification. The paper reviews and lists several potential operational challenges and difficulties experienced with the offshore station. The influences of changing conditions such as varying seawater tide level, clogged intake screen, intake sedimentation issues and marine fouling on the sump walls and structures, are discussed and mitigating solutions are identified. While it is impractical to conduct physical model test for studying flow pattern, the CFD method can be an attractive assessment tools. In addition to this, a review of plant operating parameters can assist in identifying flow anomalies to anticipate potential deterioration. Finally the difficulty in incorporating the solutions to vortex and sediment problems within the sump is highlighted with preference for those which can be managed by limited access or those which are moveable with the vertical pump.

  15. Current Conditions Risk Assessment for the 300-FF-5 Groundwater Operable Unit

    Energy Technology Data Exchange (ETDEWEB)

    Miley, Terri B.; Bunn, Amoret L.; Napier, Bruce A.; Peterson, Robert E.; Becker, James M.

    2007-11-01

    This report updates a baseline risk assessment for the 300 Area prepared in 1994. The update includes consideration of changes in contaminants of interest and in the environment that have occurred during the period of interim remedial action, i.e., 1996 to the present, as well as the sub-regions, for which no initial risk assessments have been conducted. In 1996, a record of decision (ROD) stipulated interim remedial action for groundwater affected by releases from 300 Area sources, as follows: (a) continued monitoring of groundwater that is contaminated above health-based levels to ensure that concentrations continue to decrease, and (b) institutional controls to ensure that groundwater use is restricted to prevent unacceptable exposure to groundwater contamination. In 2000, the groundwater beneath the two outlying sub-regions was added to the operable unit. In 2001, the first 5-year review of the ROD found that the interim remedy and remedial action objectives were still appropriate, although the review called for additional characterization activities. This report includes a current conditions baseline ecological and human health risk assessment using maximum concentrations in the environmental media of the 300-FF-5 Operable Unit and downstream conditions at the City of Richland, Washington. The scope for this assessment includes only current measured environmental concentrations and current use scenarios. Future environmental concentrations and future land uses are not considered in this assessment.

  16. Aerodynamic performance of a vibrating piezoelectric fan under varied operational conditions

    Science.gov (United States)

    Stafford, J.; Jeffers, N.

    2014-07-01

    This paper experimentally examines the bulk aerodynamic performance of a vibrating fan operating in the first mode of vibration. The influence of operating condition on the local velocity field has also been investigated to understand the flow distribution at the exit region and determine the stalling condition for vibrating fans. Fan motion has been generated and controlled using a piezoelectric ceramic attached to a stainless steel cantilever. The frequency and amplitude at resonance were 109.4 Hz and 12.5 mm, respectively. A test facility has been developed to measure the pressure-flow characteristics of the vibrating fan and simultaneously conduct local velocity field measurements using particle image velocimetry. The results demonstrate the impact of system characteristics on the local velocity field. High momentum regions generated due to the oscillating motion exist with a component direction that is tangent to the blade at maximum displacement. These high velocity zones are significantly affected by increasing impedance while flow reversal is a dominant feature at maximum pressure rise. The findings outlined provide useful information for design of thermal management solutions that may incorporate this air cooling approach.

  17. Investigation of a High Head Francis Turbine at Runaway Operating Conditions

    Directory of Open Access Journals (Sweden)

    Chirag Trivedi

    2016-03-01

    Full Text Available Hydraulic turbines exhibit total load rejection during operation because of high fluctuations in the grid parameters. The generator reaches no-load instantly. Consequently, the turbine runner accelerates to high speed, runaway speed, in seconds. Under common conditions, stable runaway is only reached if after a load rejection, the control and protection mechanisms both fail and the guide vanes cannot be closed. The runner life is affected by the high amplitude pressure loading at the runaway speed. A model Francis turbine was used to investigate the consequences at the runaway condition. Measurements and simulations were performed at three operating points. The numerical simulations were performed using standard k-ε, k-ω shear stress transport (SST and scale-adaptive simulation (SAS models. A total of 12.8 million hexahedral mesh elements were created in the complete turbine, from the spiral casing inlet to the draft tube outlet. The experimental and numerical analysis showed that the runner was subjected to an unsteady pressure loading up to three-times the pressure loading observed at the best efficiency point. Investigates of unsteady pressure pulsations at the vaneless space, runner and draft tube are discussed in the paper. Further, unsteady swirling flow in the blade passages was observed that was rotating at a frequency of 4.8-times the runaway runner angular speed. Apart from the unsteady pressure loading, the development pattern of the swirling flow in the runner is discussed in the paper.

  18. Validation and Verification of Future Integrated Safety-Critical Systems Operating under Off-Nominal Conditions

    Science.gov (United States)

    Belcastro, Christine M.

    2010-01-01

    Loss of control remains one of the largest contributors to aircraft fatal accidents worldwide. Aircraft loss-of-control accidents are highly complex in that they can result from numerous causal and contributing factors acting alone or (more often) in combination. Hence, there is no single intervention strategy to prevent these accidents and reducing them will require a holistic integrated intervention capability. Future onboard integrated system technologies developed for preventing loss of vehicle control accidents must be able to assure safe operation under the associated off-nominal conditions. The transition of these technologies into the commercial fleet will require their extensive validation and verification (V and V) and ultimate certification. The V and V of complex integrated systems poses major nontrivial technical challenges particularly for safety-critical operation under highly off-nominal conditions associated with aircraft loss-of-control events. This paper summarizes the V and V problem and presents a proposed process that could be applied to complex integrated safety-critical systems developed for preventing aircraft loss-of-control accidents. A summary of recent research accomplishments in this effort is also provided.

  19. Coexistence of reward and unsupervised learning during the operant conditioning of neural firing rates.

    Directory of Open Access Journals (Sweden)

    Robert R Kerr

    Full Text Available A fundamental goal of neuroscience is to understand how cognitive processes, such as operant conditioning, are performed by the brain. Typical and well studied examples of operant conditioning, in which the firing rates of individual cortical neurons in monkeys are increased using rewards, provide an opportunity for insight into this. Studies of reward-modulated spike-timing-dependent plasticity (RSTDP, and of other models such as R-max, have reproduced this learning behavior, but they have assumed that no unsupervised learning is present (i.e., no learning occurs without, or independent of, rewards. We show that these models cannot elicit firing rate reinforcement while exhibiting both reward learning and ongoing, stable unsupervised learning. To fix this issue, we propose a new RSTDP model of synaptic plasticity based upon the observed effects that dopamine has on long-term potentiation and depression (LTP and LTD. We show, both analytically and through simulations, that our new model can exhibit unsupervised learning and lead to firing rate reinforcement. This requires that the strengthening of LTP by the reward signal is greater than the strengthening of LTD and that the reinforced neuron exhibits irregular firing. We show the robustness of our findings to spike-timing correlations, to the synaptic weight dependence that is assumed, and to changes in the mean reward. We also consider our model in the differential reinforcement of two nearby neurons. Our model aligns more strongly with experimental studies than previous models and makes testable predictions for future experiments.

  20. Effects of Operating Conditions on Internal Resistances in Enzyme Fuel Cells Studied via Electrochemical Impedance Spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Aaron, D [Georgia Institute of Technology; Borole, Abhijeet P [ORNL; Yiacoumi, Sotira [Georgia Institute of Technology; Tsouris, Costas [ORNL

    2012-01-01

    Enzyme fuel cells (EFCs) offer some advantages over traditional precious-metal-catalyzed fuel cells, such as polymer electrolyte membrane fuel cells (PEMFCs). However, EFCs exhibit far less power output than PEMFCs and have relatively short life spans before materials must be replaced. In this work, electrochemical impedance spectroscopy (EIS) is used to analyze the internal resistances throughout the EFC at a variety of operating conditions. EIS analysis is focused primarily on the resistances of the anode, solution/membrane, and cathode. Increased enzyme loading results in improved power output and reductions in internal resistance. Conditions are identified for which enzyme loading does not limit the EFC performance. EIS experiments are also reported for EFCs operated continuously for 2 days; power output declines sharply over time, while all internal resistances increase. Drying of the cathode and enzyme/mediator degradation are believed to have contributed to this behavior. Finally, experiments are performed at varying air-humidification temperatures. Little effect on internal resistances or power output is observed. However, it is anticipated that increased air humidification can improve longevity by delivering more water to the cathode. Improvements to the enzymatic cathode are needed for EFC development. These improvements need to focus on improving transport rather than increasing enzyme loading.

  1. Impacts of operating conditions on nanofiltration of secondary-treated two-phase olive mill wastewater.

    Science.gov (United States)

    Ochando Pulido, Javier Miguel; Martínez Férez, Antonio

    2015-09-15

    In the present paper, a thin-film composite polymeric nanofiltration (NF) membrane is examined for the tertiary treatment of secondary-treated two-phase olive mill wastewater, in substitution of the reverse osmosis membrane used in previous work by the Authors. Overcoming the deleterious fouling phenomena persistently encountered in membrane processes managing wastewater streams was indeed pursued. Setting the adequate parameters of the operating variables - that is, operating at ambient temperature upon a net pressure equal to 13 bar (Pc), tangential crossflow in the order of 2.55 m s(-1) to attain enough turbulence over the membrane, and above the point of zero charge (pH > 5.8) of the membrane - ensured high steady-state permeate productivity (59.6 L h(-1) m(-2)), also economically sustainable in time owed to minimization of the fouling-build up rate (0.91 h(-1)). Moreover, these conditions also provided high feed recovery (90%) and significant rejection efficiencies for the electroconductivity (58.1%) and organic matter (76.1%). This led to a purified permeate stream exiting the NF membrane operation exhibiting average EC and COD values equal to 1.4 mS cm(-1) and 45 mg L(-1). This permits complying with the water quality parameters established by different regulations for discharge public waterways and irrigation purposes.

  2. Numerical Simulation and Validation of a High Head Model Francis Turbine at Part Load Operating Condition

    Science.gov (United States)

    Goyal, Rahul; Trivedi, Chirag; Kumar Gandhi, Bhupendra; Cervantes, Michel J.

    2017-07-01

    Hydraulic turbines are operated over an extended operating range to meet the real time electricity demand. Turbines operated at part load have flow parameters not matching the designed ones. This results in unstable flow conditions in the runner and draft tube developing low frequency and high amplitude pressure pulsations. The unsteady pressure pulsations affect the dynamic stability of the turbine and cause additional fatigue. The work presented in this paper discusses the flow field investigation of a high head model Francis turbine at part load: 50% of the rated load. Numerical simulation of the complete turbine has been performed. Unsteady pressure pulsations in the vaneless space, runner, and draft tube are investigated and validated with available experimental data. Detailed analysis of the rotor stator interaction and draft tube flow field are performed and discussed. The analysis shows the presence of a rotating vortex rope in the draft tube at the frequency of 0.3 times of the runner rotational frequency. The frequency of the vortex rope precession, which causes severe fluctuations and vibrations in the draft tube, is predicted within 3.9% of the experimental measured value. The vortex rope results pressure pulsations propagating in the system whose frequency is also perceive in the runner and upstream the runner.

  3. Impact of operating conditions on the removal of endocrine disrupting chemicals by membrane photocatalytic reactor.

    Science.gov (United States)

    López Fernández, Raquel; Coleman, Heather M; Le-Clech, Pierre

    2014-08-01

    This study focuses on the performance of a submerged membrane photocatalytic reactor for the removal of 17beta-oestradiol (E2) in the presence of humic acid (HA). In addition to the impact of operating parameters, such as membrane pore size, ultraviolet (UV) intensity and hydraulic retention time (HRT), the influence of long-term operation was also assessed by advanced characterization of the fouling layer formed on the membrane. The tighter (0.04 microm) hollow fibre polyvinylydene fluoride (PVDF) membrane was found to exhibit not only higher HA removal than the (0.2 microm) module (85% and 75%, respectively), but also greater transmembrane pressure (TMP) values and higher irreversible fouling. Long-term operation conditions have been simulated by conducting an ageing catalyst process and demonstrated a decrease in performance obtained with time. The artificially aged TiO2 resulted in higher TMP values and lower HA removals (about 10-20% decrease) compared with the non-aged catalyst. For E2 removal in the presence of HA, the passive adsorption of the oestrogen onto the organic matter was found to be significant (40% of the E2 adsorbed after I h), demonstrating the importance of the nature of the water matrix for this type of treatment process. An increase in the UV light intensity was observed to favour the E2 elimination, leading to more than 90% removal when using 64 W combined with PVDF membrane and an HRT of 3 h.

  4. Analysis of electric energy consumption of automatic milking systems in different configurations and operative conditions.

    Science.gov (United States)

    Calcante, Aldo; Tangorra, Francesco M; Oberti, Roberto

    2016-05-01

    Automatic milking systems (AMS) have been a revolutionary innovation in dairy cow farming. Currently, more than 10,000 dairy cow farms worldwide use AMS to milk their cows. Electric consumption is one of the most relevant and uncontrollable operational cost of AMS, ranging between 35 and 40% of their total annual operational costs. The aim of the present study was to measure and analyze the electric energy consumption of 4 AMS with different configurations: single box, central unit featuring a central vacuum system for 1 cow unit and for 2 cow units. The electrical consumption (daily consumption, daily consumption per cow milked, consumption per milking, and consumption per 100L of milk) of each AMS (milking unit + air compressor) was measured using 2 energy analyzers. The measurement period lasted 24h with a sampling frequency of 0.2Hz. The daily total energy consumption (milking unit + air compressor) ranged between 45.4 and 81.3 kWh; the consumption per cow milked ranged between 0.59 and 0.99 kWh; the consumption per milking ranged between 0.21 and 0.33 kWh; and the consumption per 100L of milk ranged between 1.80 to 2.44 kWh according to the different configurations and operational contexts considered. Results showed that AMS electric consumption was mainly conditioned by farm management rather than machine characteristics/architectures. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  5. National Utilization Patterns of Steroid Injection and Operative Intervention for Treatment of Common Hand Conditions

    Science.gov (United States)

    Sears, Erika D.; Swiatek, Peter R.; Chung, Kevin C

    2015-01-01

    Purpose To conduct a population-level analysis of practice trends and probability of surgery based on the number of steroid injections for common hand conditions. Methods Patients at least 18 years old receiving injection or surgery for carpal tunnel syndrome (CTS), trigger finger (TF), or De Quervain tenovaginitis (DQ) were identified for inclusion using the 2009–2013 Truven MarketScan databases. The number of injections performed was counted, and time between injection and operation was calculated for patients receiving both treatments. A multivariable logistic regression model was created to evaluate the odds of undergoing surgery based on the number of injections performed, controlling for patient age, sex, comorbidities, and insurance type. Results The study sample included 251,030 patients who underwent steroid injection or operative release for CTS (n=129,917), TF (n=102,778), and DQ (n=18,335). The majority of CTS patients were managed with immediate surgery (71%), whereas most patients with TF and DQ were managed initially with injection (74% and 84%, respectively). Among patients receiving both an injection and an operation, a single injection was the most common practice prior to surgery (69%, 58%, and 67% of patients with CTS, TF, and DQ, respectively). Multiple injections for DQ and TF were associated with relatively low predicted probability of surgery (17% and 26%, respectively, after 2 injections). However, the predicted probability of surgery after two injections was higher in patients with CTS (44%). Conclusions Given the associated probability of surgery after multiple injections for the three hand conditions examined, the practice of repeat injections should be critically examined to determine whether underuse or overuse is present and whether efficiency and resource utilization can be improved upon. Level of Evidence Level II (retrospective prognostic study) PMID:26774548

  6. Modal Testing and Analysis of Structures Under Operational Conditions: Industrial Applications

    Science.gov (United States)

    Hermans, L.; van der Auweraer, H.

    1999-03-01

    Experimental identification of structural dynamics models is usually based on the modal analysis approach. In the classical modal parameter estimation approach, the baseline data which are processed are frequency response functions measured under laboratory conditions. However, in many applications, the real operating conditions may differ significantly from those applied during the modal test. Hence, the need arises to identify a modal model in operational conditions. This issue is even more complicated by the fact that in most cases, only response data are measurable while the actual loading conditions are unknown. Therefore, the system identification process will need to base itself on output-only data. In the last decade, the problem of output-only modal analysis has typically been approached by applying a peak-picking technique to the auto- and cross-powers of the measured responses, resulting in operational deflection shapes and approximate estimates for the resonance frequencies. These shapes were then compared to or even decomposed into the laboratory modal results. Over the past years, several modal parameter estimation techniques have been proposed and studied for modal parameter extraction from output-only data. They include autoregressive moving averaging models, natural excitation technique (NExT) and stochastic subspace methods. In this paper, the capabilities and limitations of the NExT technique and two subspace techniques, referred to as the balanced realization and the canonical variate analysis, are evaluated for its applicability to industrial cases. The theory of the methods is briefly outlined. Subsequently, the performance of the methods is critically evaluated and compared for three industrial cases: the modal characterisation of the rear suspension system of a family car during road tests in order to understand a booming noise problem, flight flutter analysis of a commercial aircraft and the identification of the modes of a three

  7. Final Report - Membranes and MEA's for Dry, Hot Operating Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Hamrock, Steven J

    2011-06-30

    The focus of this program was to develop a new Proton Exchange Membrane (PEM) which can operate under hotter, dryer conditions than the state of the art membranes today and integrate it into a Membrane Electrode Assembly (MEA). These MEA's should meet the performance and durability requirements outlined in the solicitation, operating under low humidification conditions and at temperatures ranging from -20ºC to 120ºC, to meet 2010 DOE technical targets for membranes. This membrane should operate under low humidification conditions and at temperatures ranging from -20ºC to 120ºC in order to meet DOE HFCIT 2010 commercialization targets for automotive fuel cells. Membranes developed in this program may also have improved durability and performance characteristics making them useful in stationary fuel cell applications. The new membranes, and the MEA's comprising them, should be manufacturable at high volumes and at costs which can meet industry and DOE targets. This work included: A) Studies to better understand factors controlling proton transport within the electrolyte membrane, mechanisms of polymer degradation (in situ and ex situ) and membrane durability in an MEA; B) Development of new polymers with increased proton conductivity over the range of temperatures from -20ºC to 120ºC and at lower levels of humidification and with improved chemical and mechanical stability; C) Development of new membrane additives for increased durability and conductivity under these dry conditions; D) Integration of these new materials into membranes and membranes into MEA's, including catalyst and gas diffusion layer selection and integration; E) Verification that these materials can be made using processes which are scalable to commercial volumes using cost effective methods; F) MEA testing in single cells using realistic automotive testing protocols. This project addresses technical barriers A (Durability) and C (Performance) from the Fuel Cells section of the

  8. Standardization of the energy performance of photovoltaic modules in real operating conditions

    Directory of Open Access Journals (Sweden)

    Viganó Davide

    2014-01-01

    Full Text Available The performance of a PV module at STC [1] is a useful indicator for comparing the peak performance of different module types, but on its own is not sufficient to accurately predict how much energy a module will deliver in the field when subjected to a wide range of real operating conditions [2]. An Energy Rating approach has to be preferred for that aim. It is currently under development the standard series IEC 61853 on Energy Rating, for which only part 1 [3] has been issued. It describes methods to characterize the module performance as a function of irradiance and temperature. The reproducibility of the power matrix measurements obtained by the three different methods specified in the standard, namely: under natural sunlight using a tracking system; under natural sunlight without tracker; and a large area pulsed solar simulator of Class AAA were evaluated and discussed [4,5]. The work here presented is focused on the second method listed above, which explores the real working conditions for a PV device and therefore it represents the situation where Energy Rating procedures are expected to give the largest deviations from the STC predictions. The system for continuous monitoring of module performances, already implemented at ESTI, has been recently replaced with a new system having a number of improvements described in the following. The two system results have been compared showing a discrete compatibility. The two power matrices are then merged together using a weighted average and compared to those acquired with the other two remaining “ideal” systems. An interesting tendency seems to come up from this comparison, making the power rating under real operating conditions an essential procedure for energy rating purposes.

  9. Combining models of behaviour with operational data to provide enhanced condition monitoring of AGR cores

    Energy Technology Data Exchange (ETDEWEB)

    West, Graeme M., E-mail: graeme.west@strath.ac.uk; Wallace, Christopher J.; McArthur, Stephen D.J.

    2014-06-01

    Highlights: • Combining laboratory model outputs with operational data. • Isolation of single component from noisy data. • Better understanding of the health of graphite cores. • Extended plant operation through leveraging existing data sources. - Abstract: Installation of new monitoring equipment in Nuclear Power Plants (NPPs) is often difficult and expensive and therefore maximizing the information that can be extracted from existing monitoring equipment is highly desirable. This paper describes the process of combining models derived from laboratory experimentation with current operational plant data to infer an underlying measure of health. A demonstration of this process is provided where the fuel channel bore profile, a measure of core health, is inferred from data gathered during the refuelling process of an Advanced Gas-cooled Reactor (AGR) nuclear power plant core. Laboratory simulation was used to generate a model of an interaction between the fuel assembly and the core. This model is used to isolate a single frictional component from a noisy input signal and use this friction component as a measure of health to assess the current condition of the graphite bricks that comprise the core. In addition, the model is used to generate an expected refuelling response (the noisy input signal) for a given set of channel bore diameter measurements for either insertion of new fuel or removal of spent fuel, providing validation of the model. This benefit of this work is that it provides a greater understanding of the health of the graphite core, which is important for continued and extended operation of the AGR plants in the UK.

  10. SUBURBAN VS. URBAN FRINGES ENTITIES’ WILLINGNESS TO PAY FOR AMENITIES: EMPIRICAL RESEARCH IN CRACOW CITY, POLAND

    Directory of Open Access Journals (Sweden)

    Piotr LITYŃSKI

    2015-06-01

    Full Text Available The aim of this paper is to estimate the value of selected amenities of infrastructure, space and public services on both sides of the cities’ administrative borders and its territorial implications. The used method is the estimation of WTP. The method was addressed to households and companies located in the district adjoining areas which are administratively not part of the city, and that are judged to be strongly characterized by the processes of suburbanization. The conclusions of the study indicate that the administrative border of the city is polarized in terms of a household economic profile. Residents of both regions express their needs for amenities and suburban residents generally estimate their value higher. While firms from both areas are not interested in improvements, the administrative border of the city does not really differentiate businesses (size, employment, wages

  11. A gap theorem for the ZL-amenability constant of a finite group

    Directory of Open Access Journals (Sweden)

    Yemon Choi

    2016-12-01

    Full Text Available It was shown in [A. Azimifard, E. Samei, N. Spronk, JFA 256 (2009] that the ZL-amenability constant of a finite group is always at least~$1$, with equality if and only if the group is abelian. It was also shown in [A. Azimifard, E. Samei, N. Spronk, op cit.] that for any finite non-abelian group this invariant is at least $301/300$, but the proof relies crucially on a deep result of D. A. Rider on norms of central idempotents in group algebras.Here we show that if $G$ is finite and non-abelian then its ZL-amenability constant is at least $7/4$, which is known to be best possible. We avoid use of Rider's reslt, by analyzing the cases where $G$ is just non-abelian, using calculations from [M. Alaghmandan, Y. Choi, E. Samei, CMB 57 (2014], and establishing a new estimate for groups with trivial centre.

  12. H\\"{o}lder continuous retractions and amenable semigroups of uniformly Lipschitzian mappings in Hilbert spaces

    CERN Document Server

    Wiśnicki, Andrzej

    2012-01-01

    Suppose that S is a left amenable semitopological semigroup. We prove that if $\\{T_{t}: t \\in S \\}$ is a uniformly k-Lipschitzian semigroup on a bounded closed and convex subset C of a Hilbert space and $k<\\sqrt{2}$, then the set of fixed points of this semigroup is a H\\"{o}lder continuous retract of C. This gives a qualitative complement to the Ishihara-Takahashi fixed point existence theorem.

  13. Moles and Mole Control on British Farms, Amenities and Gardens after Strychnine Withdrawal

    Directory of Open Access Journals (Sweden)

    Sandra E. Baker

    2016-06-01

    Full Text Available Moles are considered pests in Britain, but this issue has been little studied. Lower welfare standards have been tolerated for moles than for most other managed wild mammal species, as use of both the controversial poison, strychnine, and unregulated traps have been permitted. Strychnine was withdrawn in 2006 and there were fears that mole populations would increase as a result. In 2007, we conducted a comprehensive, nationwide survey of land manager perceptions, opinions and behaviour regarding moles and mole control on farms, amenities and domestic gardens in Britain. We surveyed 2150 land managers (achieving a 59% response rate and ground-truthed 29 responses. Moles were reported to be present on most farms and amenities, and 13% of gardens, and were more common in lighter soils. Where present, moles were usually considered pests, this being more likely in Wales, Scotland and northern England, on livestock and mixed farms, and on large, high-value amenities, e.g., racecourses and golf courses. Mole control followed similar patterns to mole presence. More control may occur than is economically, and therefore potentially ethically, justified. Control should be more carefully considered and, where necessary, more effectively targeted. Kill-trapping was the favoured recent and future method on farms and amenities, even if strychnine was to be reintroduced; however, because mole traps are currently unregulated, some might not meet current welfare standards if tested. We found no evidence for an increase in moles since a farm questionnaire survey conducted in 1992; this could have wider implications for future wildlife management policy changes.

  14. Moles and Mole Control on British Farms, Amenities and Gardens after Strychnine Withdrawal.

    Science.gov (United States)

    Baker, Sandra E; Ellwood, Stephen A; Johnson, Paul J; Macdonald, David W

    2016-06-08

    Moles are considered pests in Britain, but this issue has been little studied. Lower welfare standards have been tolerated for moles than for most other managed wild mammal species, as use of both the controversial poison, strychnine, and unregulated traps have been permitted. Strychnine was withdrawn in 2006 and there were fears that mole populations would increase as a result. In 2007, we conducted a comprehensive, nationwide survey of land manager perceptions, opinions and behaviour regarding moles and mole control on farms, amenities and domestic gardens in Britain. We surveyed 2150 land managers (achieving a 59% response rate) and ground-truthed 29 responses. Moles were reported to be present on most farms and amenities, and 13% of gardens, and were more common in lighter soils. Where present, moles were usually considered pests, this being more likely in Wales, Scotland and northern England, on livestock and mixed farms, and on large, high-value amenities, e.g., racecourses and golf courses. Mole control followed similar patterns to mole presence. More control may occur than is economically, and therefore potentially ethically, justified. Control should be more carefully considered and, where necessary, more effectively targeted. Kill-trapping was the favoured recent and future method on farms and amenities, even if strychnine was to be reintroduced; however, because mole traps are currently unregulated, some might not meet current welfare standards if tested. We found no evidence for an increase in moles since a farm questionnaire survey conducted in 1992; this could have wider implications for future wildlife management policy changes.

  15. Street trees and equity: evaluating the spatial distribution of an urban amenity

    OpenAIRE

    Shawn M. Landry; Jayajit Chakraborty

    2009-01-01

    While urban disamenities and pollution sources have received considerable attention in environmental justice research, few studies have examined sociospatial inequities associated with the distribution of desirable land uses. In this paper we focus on addressing this limitation by investigating the environmental equity implications of street trees—an important publicly financed amenity that provides several direct and indirect benefits to urban residents. The specific objective was to determi...

  16. Estimating the Economic Value of Environmental Amenities of Isfahan Sofeh Highland Park (The Individual Revealed and Expressed Travel Cost Method

    Directory of Open Access Journals (Sweden)

    H. Amirnejad

    2016-03-01

    the above values are not the price of Sofeh Park that is a natural environment in the current study. In fact, these values are "minimum of recreational values" of any given environment. It is essential for the visitors to have knowledge of this value in order to conserve the environment and the regional facilities. Furthermore, it is essential for the authorities to have knowledge of this value, with the aim of making more efforts and overseeing improvements and conservation of this environment. Also, alongside the protection plans for Sofeh Highland Park, authorities can bring about an increase in the number of annual visits to this Park by reducing travel and opportunity costs through facilitating the conditions to access, such as improving public transportation to this park. Keywords: Individual Travel Costs, Isfahan Sofeh Highland Park, Negative Binomial Regression, Value of Environmental Amenities, Tourism Demand Function

  17. First experience in operating the population of the condition database for the CMS experiment

    CERN Document Server

    De Gruttola, M; Futyan, David; Glege, Frank; Govi, Giacomo; Innocente, Vincenzo; Paolucci, Pierluigi; Pierro, Antonio; Schlatter, Dieter

    2010-01-01

    Reliable population of the condition database is critical for the correct operation of the online selection as well as of the offline reconstruction and analysis of data. We will describe here the system put in place in the CMS experiment to populate the database and make condition data promptly available both online for the high-level trigger and offline for reconstruction. The system, designed for high flexibility to cope with very different data sources, uses POOL-ORA technology in order to store data in an object format that best matches the object oriented paradigm for C++ programming language used in the CMS offline software. In order to ensure consistency among the various subdetectors, a dedicated package, PopCon (Populator of Condition Objects), is used to store data online. The data are then automatically streamed to the offline database hence immediately accessible offline worldwide. This mechanism was intensively used during 2008 in the test-runs with cosmic rays. The experience of this first mont...

  18. A hydrodynamic optimization design methodology for a ship bulbous bow under multiple operating conditions

    Directory of Open Access Journals (Sweden)

    Yu Lu

    2016-01-01

    Full Text Available The main objective of this article is to describe an innovative methodology for the hydrodynamic optimization of a ship bulbous bow which considers multiple operating conditions. The proposed method is more practical and effective than the traditional optimization process, which is only based on contractually specified design condition. Parametric form approaches are adopted by employing an F-spline curve in order to generate variants of the hull bulbous bow forms using form design parameters modified, resulting in an optimization system based on improved genetic algorithms. The Rankine source panel method is used for the hydrodynamic evaluation, wherein non-linear free surface conditions and the trim and sinkage of the ship are taken into consideration. The validity and effectiveness of the proposed methodology for a large container ship is investigated by comparing the computational results with experimental data, which demonstrates that the proposed methodology can engage well in the automation process and improve hydrodynamic performance during actual ship design practices.

  19. Operating conditions for the continuous bioremediation of free cyanide contaminated wastewater using Aspergillus awamori.

    Science.gov (United States)

    Santos, B A Q; Ntwampe, S K O; Doughari, J H; Muchatibaya, G

    2014-01-01

    Generation of cyanide-containing wastewater is a growing problem worldwide as numerous cyanide complexes are highly unstable and degrade to form free cyanide (F-CN), the most toxic form of cyanide. Agro-waste materials, such as sweet orange (Citrus sinensis) waste from the citrus industry, are rich in readily metabolisable carbohydrates that can supplement microbial activity and thus support biodegradation of toxic compounds in wastewater. This study reports on optimal operating conditions for the continuous biodegradation of F-CN in wastewater using an Aspergillus awamori isolate in a process supported solely using C. sinensis waste extract. The optimal degradation conditions were pH 8.75 and 37.02 °C with the isolate's F-CN tolerance being observed up to 430 mg F-CN/L. Furthermore, the ammonium produced as a by-product of F-CN degradation was also metabolised by the A. awamori, with negligible residual citric acid and formate being observed in the effluent post treatment. This study demonstrates the feasibility of using agricultural waste as a primary and sole carbon source for the cultivation of a cyanide-degrading A. awamori species for F-CN degradation under alkaline conditions.

  20. OPTIMIZATION OF THE OPERATING CONDITIONS FOR RHAMNOLIPID PRODUCTION USING SLAUGHTERHOUSE-GENERATED INDUSTRIAL FLOAT AS SUBSTRATE

    Directory of Open Access Journals (Sweden)

    W. S. Borges

    2015-06-01

    Full Text Available AbstractBiosurfactants have a wide range of applications in emulsions, separations, and solubilization because these chemicals reduce the surface tension and viscosity of solutions. This work studied rhamnolipid production using a batch bioreactor with a working volume of 1.5 liters, Pseudomonas aeruginosa ATCC (American Type Culture Collection 10145 strain, and the greasy effluent from the slaughter of poultry and pigs as the substrate. The main goal of this research was to evaluate the level of aeration, agitation speed and inoculum concentration using a Central Composite Design (CCD. Experimental conditions were selected using the surface response technique obtained from the CCD, and the results were validated to test the reproducibility. The following operating conditions were selected: 1.2 vvm level of aeration, 600 rpm agitation speed, and 1.0 g/L biomass inoculum concentration. Under these conditions, the following results were obtained: the rhamnose production, surface tension and emulsifying index were 5.37 g/L, 25.6 dyne/cm and 100%, respectively.

  1. Understanding the Importance of Urban Amenities: A Case Study from Auckland

    Directory of Open Access Journals (Sweden)

    Natalie Allen

    2015-01-01

    Full Text Available Along with many Pacific Rim cities in Australia and North America, Auckland, New Zealand has enacted an urban growth management strategy premised on two concepts: “liveability” and a “quality compact city”. The effective implementation of this strategy will, in part, require higher density housing typologies to be developed within the existing suburban fabric. The urban amenities in a neighbourhood play an important role in providing a sense of liveability for residents. This paper examines these issues by evaluating and reporting on key outcomes from 57 face-to-face qualitative interviews with residents who currently live in medium density housing in four Auckland suburbs; Takapuna, Kingsland, Botany Downs, and Te Atatu Peninsula. Findings consider the trade-offs residents make when choosing to live in medium density housing typologies, how they value the urban amenities in their neighbourhood and the role they think these amenities play in their location satisfaction. Conclusions are drawn around how the resident-derived information may inform the market on the supply side of housing, and comment is made about how these preferences may, or may not, respond to the objectives of the underlying urban management strategies involved.

  2. Large Reductions In Amenable Mortality Associated With Brazil's Primary Care Expansion And Strong Health Governance.

    Science.gov (United States)

    Hone, Thomas; Rasella, Davide; Barreto, Mauricio; Atun, Rifat; Majeed, Azeem; Millett, Christopher

    2017-01-01

    Strong health governance is key to universal health coverage. However, the relationship between governance and health system performance is underexplored. We investigated whether expansion of the Brazilian Estratégia de Saúde da Família (ESF; family health strategy), a community-based primary care program, reduced amenable mortality (mortality avoidable with timely and effective health care) and whether this association varied by municipal health governance. Fixed-effects longitudinal regression models were used to identify the relationship between ESF coverage and amenable mortality rates in 1,622 municipalities in Brazil over the period 2000-12. Municipal health governance was measured using indicators from a public administration survey, and the resulting scores were used in interactions. Overall, increasing ESF coverage from 0 percent to 100 percent was associated with a reduction of 6.8 percent in rates of amenable mortality, compared with no increase in ESF coverage. The reductions were 11.0 percent for municipalities with the highest governance scores and 4.3 percent for those with the lowest scores. These findings suggest that strengthening local health governance may be vital for improving health services effectiveness and health outcomes in decentralized health systems.

  3. Conditioning of sludge produced through chemical treatment of radioactive liquid waste - Operating experiences

    Energy Technology Data Exchange (ETDEWEB)

    Reddy, D. Anji, E-mail: anji@igcar.gov.i [Centralised Waste Management Facility, Nuclear Recycle Group, BARC Facilities, Kalpakkam 603 102, Tamil Nadu (India); Khandelwal, S.K.; Muthiah, R.; Shanmugamani, A.G.; Paul, Biplob; Rao, S.V.S.; Sinha, P.K. [Centralised Waste Management Facility, Nuclear Recycle Group, BARC Facilities, Kalpakkam 603 102, Tamil Nadu (India)

    2010-07-15

    At Centralised Waste Management Facility (CWMF) 160 m{sup 3} of radioactive chemical sludge, generated from treatment of several batches of category-II and category-III radioactive liquid wastes by chemical precipitation method was stored in clariflocculator (CF) for downstream processing. The sludge needed conditioning before disposal. The analysis of the sludge samples collected at different radial locations and depths from the CF showed suspended solid content of 2.37-13.07% and radioactive content of gross {beta}-{gamma} 5000-27,000 Bq/g and {alpha} 100-600 Bq/g. After comparing different options available for conditioning of the sludge based on their technological and economical aspects, it was decided to dewater it using centrifuge before fixing in cement matrix with additives. Process Control Laboratory of CWMF studied the process in detail to optimize the relevant parameters for fixation of the concentrate obtained from centrifuge. Based on these results, conditioning of the stored sludge was undertaken. The process consisted of diluting the sludge with low active effluents/water for homogenisation and facilitating the transfer of sludge, dewatering of the slurry utilising decanter centrifuge, fixation of dewatered concentrate in Ordinary Portland Cement (OPC) with vermiculite as an additive using in-drum mixing method, providing sufficient time for hardening of fixed mass, transportation and safe disposal into Near Surface Disposal Facility (NSDF). Total 150 m{sup 3} of conditioned waste was produced (750 numbers of drums containing cement fixed concentrate). The paper includes the results of the studies conducted on cement fixed concentrate blocks for finding out their compressive strength and leaching characteristics. It also describes the experiences gained from the above operations.

  4. The optimum operating conditions of the phased double-rotor facility at the ET-RR-1 reactor

    Energy Technology Data Exchange (ETDEWEB)

    Naguib, K.; Habib, N.; Wahba, M.; Kilany, M.; Adib, M. [National Research Centre, Cairo (Egypt). Reactor and Neutron Physics Dept.

    1997-02-07

    A pulsed neutron polyenergetic thermal beam at ET-RR-1 is produced by a phased double-rotor facility. One of the rotors has two diametrically opposite curved slots, while the second is designed to operate as a rotating collimator. The dimensions of the phased rotating collimator are selected to match the curved slot rotor. The calculated collimator transmissions at different operating conditions are found to be in good agreement with the experimental ones. The optimum operating conditions of the double-rotor facility are deduced. The calculations were carried out using a computer program RCOL. The RCOL was designed in FORTRAN-77 to operate on PCs. (author).

  5. Wind tunnel testing of the DeepWind demonstrator in design and tilted operating conditions

    DEFF Research Database (Denmark)

    Battistia, L.; Benini, E.; Brighenti, A.

    2016-01-01

    ) configuration. The velocity field in the wake of the rotor was also fully characterized by means of an instrumented traversing system, to investigate the flow distribution downstream of the test section. Special care is taken in the description of the experimental set-up and of the measured data, so......The DeepWind Project aims at investigating the feasibility of a new floating vertical-axis wind turbine (VAWT) concept, whose purpose is to exploit wind resources at deep-water offshore sites. The results of an extensive experimental campaign on the DeepWind reduced scale demonstrator are here...... was installed on a high precision test bench, whose axis was suitable to be inclined up to 15° with respect to the design (i.e. upright) operating condition. The experiments were performed at the large scale, high speed wind tunnel of the Politecnico di Milano (Italy), using a “free jet” (open channel...

  6. Reverse osmosis filtration for space mission wastewater: membrane properties and operating conditions

    Science.gov (United States)

    Lee, S.; Lueptow, R. M.

    2001-01-01

    Reverse osmosis (RO) is a compact process that has potential for the removal of ionic and organic pollutants for recycling space mission wastewater. Seven candidate RO membranes were compared using a batch stirred cell to determine the membrane flux and the solute rejection for synthetic space mission wastewaters. Even though the urea molecule is larger than ions such as Na+, Cl-, and NH4+, the rejection of urea is lower. This indicates that the chemical interaction between solutes and the membrane is more important than the size exclusion effect. Low pressure reverse osmosis (LPRO) membranes appear to be most desirable because of their high permeate flux and rejection. Solute rejection is dependent on the shear rate, indicating the importance of concentration polarization. A simple transport model based on the solution-diffusion model incorporating concentration polarization is used to interpret the experimental results and predict rejection over a range of operating conditions. Grant numbers: NAG 9-1053.

  7. A Review & Assessment of Current Operating Conditions Allowable Stresses in ASME Section III Subsection NH

    Energy Technology Data Exchange (ETDEWEB)

    R. W. Swindeman

    2009-12-14

    The current operating condition allowable stresses provided in ASME Section III, Subsection NH were reviewed for consistency with the criteria used to establish the stress allowables and with the allowable stresses provided in ASME Section II, Part D. It was found that the S{sub o} values in ASME III-NH were consistent with the S values in ASME IID for the five materials of interest. However, it was found that 0.80 S{sub r} was less than S{sub o} for some temperatures for four of the materials. Only values for alloy 800H appeared to be consistent with the criteria on which S{sub o} values are established. With the intent of undertaking a more detailed evaluation of issues related to the allowable stresses in ASME III-NH, the availabilities of databases for the five materials were reviewed and augmented databases were assembled.

  8. Reverse osmosis filtration for space mission wastewater: membrane properties and operating conditions

    Science.gov (United States)

    Lee, S.; Lueptow, R. M.

    2001-01-01

    Reverse osmosis (RO) is a compact process that has potential for the removal of ionic and organic pollutants for recycling space mission wastewater. Seven candidate RO membranes were compared using a batch stirred cell to determine the membrane flux and the solute rejection for synthetic space mission wastewaters. Even though the urea molecule is larger than ions such as Na+, Cl-, and NH4+, the rejection of urea is lower. This indicates that the chemical interaction between solutes and the membrane is more important than the size exclusion effect. Low pressure reverse osmosis (LPRO) membranes appear to be most desirable because of their high permeate flux and rejection. Solute rejection is dependent on the shear rate, indicating the importance of concentration polarization. A simple transport model based on the solution-diffusion model incorporating concentration polarization is used to interpret the experimental results and predict rejection over a range of operating conditions. Grant numbers: NAG 9-1053.

  9. RANS simulation of cavitation and hull pressure fluctuation for marine propeller operating behind-hull condition

    Directory of Open Access Journals (Sweden)

    Kwang-Jun Paik

    2013-12-01

    Full Text Available Simulations of cavitation flow and hull pressure fluctuation for a marine propeller operating behind a hull using the unsteady Reynolds-Averaged Navier-Stokes equations (RANS are presented. A full hull body submerged under the free surface is modeled in the computational domain to simulate directly the wake field of the ship at the propeller plane. Simulations are performed in design and ballast draught conditions to study the effect of cavitation number. And two propellers with slightly different geometry are simulated to validate the detectability of the numerical simulation. All simulations are performed using a commercial CFD software FLUENT. Cavitation patterns of the simulations show good agreement with the experimental results carried out in Samsung CAvitation Tunnel (SCAT. The simulation results for the hull pressure fluctuation induced by a propeller are also compared with the experimental results showing good agreement in the tendency and amplitude, especially, for the first blade frequency.

  10. Characterization of hot-gas filter ash under PFBC operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, A.K.; Swanson, M.L.; Hurley, J.P.; Watne, E.M. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center

    1997-12-31

    The objective of this program was to perform bench-scale dynamic tests of ash formation and long-term ash cake formation in pressurized fluidized-bed combustion (PFBC) systems to help in the development of methods to predict possible filter bridging problems and suggest possible strategies for mitigating these problems. During the program, four ash formation tests using a washed coal from the Consol Enlow Fork mine, with two size distributions of Plum Run dolomite at two different temperatures, were completed under conditions simulating the operation of the American Electric Power (AEP) Tidd PFBC. In addition, the same test matrix, plus two tests using no sorbent, was completed with the Belle Ayr Powder River Basin subbituminous coal, which will be used at the Southern Company Services (SCS) Wilsonville, Alabama, power systems development facility (PSDF).

  11. Characterization of hot-gas filter ash under PFBC operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, A.K.; Swanson, M.L.; Hurley, J.P.; Watne, T.M.

    1998-01-01

    The objective of this program was to perform bench scale dynamic tests of ash formation and long-term ash cake formation in pressurized fluidized bed combustion (PFBC) systems to help in the development of methods to predict possible filter bridging problems and suggest possible strategies for mitigating these problems. During the program, four ash formation tests using a washed coal from the Consol Enlow Fork mine, with two size distributions of Plum Run dolomite at two different temperatures, were completed under conditions simulating the operation of the American Electric Power (AEP) Tidd PFBC. In addition, the same test matrix, plus two tests using no sorbent, was completed with the Belle Ayr Powder River Basin sub-bituminous coal, which will be used at the Southern Company Services (SCS) Wilsonville, Alabama, power systems development facility (PSDF).

  12. Reaction Mechanism of Thiophene on Vanadium Oxides under FCC Operating Conditions

    Institute of Scientific and Technical Information of China (English)

    Wang Peng; Zheng Aiguo; Tian Huiping; Long Jun

    2004-01-01

    The reaction mechanism of thiophene on vanadium oxides under FCC operating conditions had been preliminary studied using in-situ FT-IR analysis of thiophene and atmospheric pressure continuous fixed-bed reaction, followed by characterization via pyridine adsorption-temperature programmed desorption method, and FT-IR and XPS spectra. The research had discovered that, under 500C thiophene could undergo the redox reaction with V2O5, while being converted into CO, CO2 as well as SO2 with its conversion rate reaching 41.2%. At the same time the oxidation number of vanadium decreased. The existence of a few Bronsted acid centers on V2O5 could lead to an increase of H2S yield among the products derived from the reaction with thiophene.

  13. Study and Development of an Air Conditioning System Operating on a Magnetic Heat Pump Cycle

    Science.gov (United States)

    Wang, Pao-Lien

    1991-01-01

    This report describes the design of a laboratory scale demonstration prototype of an air conditioning system operating on a magnetic heat pump cycle. Design parameters were selected through studies performed by a Kennedy Space Center (KSC) System Simulation Computer Model. The heat pump consists of a rotor turning through four magnetic fields that are created by permanent magnets. Gadolinium was selected as the working material for this demonstration prototype. The rotor was designed to be constructed of flat parallel disks of gadolinium with very little space in between. The rotor rotates in an aluminum housing. The laboratory scale demonstration prototype is designed to provide a theoretical Carnot Cycle efficiency of 62 percent and a Coefficient of Performance of 16.55.

  14. Physiotherapy-provided operant conditioning in the management of low back pain disability: A systematic review.

    Science.gov (United States)

    Bunzli, Samantha; Gillham, David; Esterman, Adrian

    2011-03-01

     Non-specific low back pain (LBP) is a leading cause of disability in developed countries. Behavioural interventions have been found efficacious in reducing disability in LBP. Operant conditioning is one type of behavioural intervention being employed by physiotherapists; however, the effectiveness of physiotherapist-provided operant conditioning (POC) in the management of LBP disability is unknown. This review aims to answer the question: is POC more effective than comparison interventions in reducing LBP disability?   A systematic review of randomized controlled trials was conducted using a qualitative analysis of effect. Participants were adults ≥18 years with non-specific LBP. The intervention was defined as a time contingent, graduated increase in activity including goal setting and the education and reinforcement of positive pain behaviours with the aim of decreasing disability. The primary outcome measure was back pain specific disability. Secondary outcomes included generic functional status, pain intensity, sick leave, fear avoidance beliefs or behaviour and adverse effects.   Fifteen trials involving 3737 people were included. Eight studies reported a clinically significant difference. The POC intervention was not found to be inferior to any of the comparison interventions in reducing disability. Moderate evidence was found that POC is more effective than other behavioural interventions in reducing long term disability in chronic LBP. Moderate evidence showed POC may be more effective than other treatments in reducing post-treatment fear avoidance beliefs in a sub-acute population but less effective in reducing short term fear avoidance beliefs in a population with mixed LBP. Moderate evidence showed POC is more effective than a placebo intervention in reducing short term pain in sub-acute LBP.   POC may be considered efficacious in the treatment of LBP. Physiotherapists may also consider POC for its additional effect of reducing long term

  15. Influence of the operating conditions on highly oxidative radicals generation in Fenton's systems.

    Science.gov (United States)

    Ciotti, Cesare; Baciocchi, Renato; Tuhkanen, Tuula

    2009-01-15

    In this work, an indirect method for estimating the total amount and concentration of oxidative radicals in aqueous and slurry-phase Fenton's systems was developed. This method, based on the use of benzoic acid as probe compound, was applied for evaluating the effect of the operating conditions on the radicals amount produced, their production efficiency (i.e. moles of radicals generated per mole H2O2 and their concentration. A Rotatable Central Composite design (RCC) was used to select the operating conditions in order to get a statistically meaningful data set. Hydrogen peroxide and ferrous ion concentrations ranged between 0.2-1mM and 0.2-0.5mM, respectively; humic acid concentration between 0 and 15mg/L, whereas the soil/water weight ratio in slurry-phase systems between 1:10 and 9:10. The probe compound concentration was 9 or 0.1mM in experiments aimed to evaluate the total amount or concentration of oxidative radicals, respectively. The obtained results indicated that the amount of radicals generated in both aqueous and soil slurry Fenton's system increased with higher H2O2 concentration and, more specifically, that their production efficiency increased with increasing Fe(II):H2O2 molar ratio. Addition of dissolved organic compounds as humic acid did not notably affect the oxidative radicals amount and concentration. On the contrary, a one order of magnitude reduction in both radicals amount generated and concentration was observed when soil was added to the reaction environment.

  16. Two simple multivariate procedures for monitoring planetary gearboxes in non-stationary operating conditions

    Science.gov (United States)

    Zimroz, Radoslaw; Bartkowiak, Anna

    2013-07-01

    This paper deals with the diagnostics of planetary gearboxes under nonstationary operating conditions. In most diagnostics applications, energy of vibration signals (calculated directly from time series or extracted from spectral representation of signal) is used. Unfortunately energy based features are sensitive to load conditions and it makes diagnostics difficult. In this paper we used energy based 15D data vectors (namely spectral amplitudes of planetary mesh frequency and its harmonics) in order to investigate if it is possible to improve diagnostics efficiency in comparison to previous, one dimensional, approaches proposed for the same problem. Two multivariate methods, Principal Component Analysis (PCA) and Canonical Discriminant Analysis (CDA), were used as techniques for data analysis. We used these techniques in order to investigate dimensionality of the data and to visualize data in 3D and 2D spaces in order to understand data behavior and assess classification ability. As a case study the data from two planetary gearboxes used in complex mining machines (one in bad condition and the other in good condition) were analyzed. For these two machines more than 2000 15D vectors were acquired. It should be noted that due to non-stationarity of loading conditions, previous diagnostics results obtained using other techniques were moderately good (ca. 80% recognition efficiency); however there is still some need to improve diagnostics classification ability. After application of the proposed approaches it was found that the entire data could be reduced to 2 dimensions whereby data instances became visible and a good discriminant function (characterized by a misclassification rate of .0023, i.e. only 5 erroneous classifications for a total of 2183 instances) could be derived. This paper suggests a novel way for condition monitoring of planetary gearboxes based on multivariate statistics. The emphasis is put on the algebraic and geometric interpretations of the PCA

  17. Mercury-Cadmium-Telluride Focal Plane Array Performance Under Non-Standard Operating Conditions

    Science.gov (United States)

    Richardson, Brandon S.; Eastwood, Michael L.; Bruce, Carl F.; Green, Robert O.; Coles, J. B.

    2011-01-01

    This paper highlights a new technique that allows the Teledyne Scientific & Imaging LLC TCM6604A Mercury-Cadmium-Telluride (MCT) Focal Plane Array (FPA) to operate at room temperature. The Teledyne MCT FPA has been a standard in Imaging Spectroscopy since its creation in the 1980's. This FPA has been used in applications ranging from space instruments such as CRISM, M3 and ARTEMIS to airborne instruments such as MaRS and the Next Generation AVIRIS Instruments1. Precise focal plane alignment is always a challenge for such instruments. The current FPA alignment process results in multiple cold cycles requiring week-long durations, thereby increasing the risk and cost of a project. These alignment cycles are necessary because optimal alignment is approached incrementally and can only be measured with the FPA and Optics at standard operating conditions, requiring a cold instrument. Instruments using this FPA are normally cooled to temperatures below 150K for the MCT FPA to properly function. When the FPA is run at higher temperatures the dark current increases saturating the output. This paper covers the prospect of warm MCT FPA operation from a theoretical and experimental perspective. We discuss the empirical models and physical laws that govern MCT material properties and predict the optimal settings that will result in the best MCT PA performance at 300K. Theoretical results are then calculated for the proposed settings. We finally present the images and data obtained using the actual system with the warm MCT FPA settings. The paper concludes by emphasizing the strong positive correlation between the measured values and the theoretical results.

  18. Mercury-Cadmium-Telluride Focal Plane Array Performance Under Non-Standard Operating Conditions

    Science.gov (United States)

    Richardson, Brandon S.; Eastwood, Michael L.; Bruce, Carl F.; Green, Robert O.; Coles, J. B.

    2011-01-01

    This paper highlights a new technique that allows the Teledyne Scientific & Imaging LLC TCM6604A Mercury-Cadmium-Telluride (MCT) Focal Plane Array (FPA) to operate at room temperature. The Teledyne MCT FPA has been a standard in Imaging Spectroscopy since its creation in the 1980's. This FPA has been used in applications ranging from space instruments such as CRISM, M3 and ARTEMIS to airborne instruments such as MaRS and the Next Generation AVIRIS Instruments1. Precise focal plane alignment is always a challenge for such instruments. The current FPA alignment process results in multiple cold cycles requiring week-long durations, thereby increasing the risk and cost of a project. These alignment cycles are necessary because optimal alignment is approached incrementally and can only be measured with the FPA and Optics at standard operating conditions, requiring a cold instrument. Instruments using this FPA are normally cooled to temperatures below 150K for the MCT FPA to properly function. When the FPA is run at higher temperatures the dark current increases saturating the output. This paper covers the prospect of warm MCT FPA operation from a theoretical and experimental perspective. We discuss the empirical models and physical laws that govern MCT material properties and predict the optimal settings that will result in the best MCT PA performance at 300K. Theoretical results are then calculated for the proposed settings. We finally present the images and data obtained using the actual system with the warm MCT FPA settings. The paper concludes by emphasizing the strong positive correlation between the measured values and the theoretical results.

  19. Aeroacoustic Simulation for NASA CC3 Centrifugal Compressor Operating at off Design Condition

    Directory of Open Access Journals (Sweden)

    Alqaradawi Mohamed

    2016-01-01

    Full Text Available This paper covers the characterization of the acoustic noise and the unsteady flow field of a high speed centrifugal compressor NASA CC3. In order to accurately predict the noise, all analyses are carried out through the use of Large Eddy Simulation and Ffowcs Williams–Hawkings model for noise prediction. The relative effect of hub cavity on flow characteristics and sound levels is investigated, for a compressor stage with a total pressure ratio equal to 4, working from surge to near choke condition. In comparison with the experimental results from literature, the predicted compressor performance and flow field are predicted well. The hub cavity flow effect on the compressor aeroacoustic generated noise is shown in the paper. The unsteady static pressure and sound pressure levels are compared not only at different location but also for design and off design operating points. The internal flow results inside the hub cavity are presented at surge, design and near choke points. The conclusion is that the cavity effect of the centrifugal compressor cannot be ignored in the numerical prediction of aerodynamic generated noise. The impeller back plate of the rotor experiences a strong pressure fluctuation, which is maxima at the impeller outer radius for all operating point, but higher pressure values at the surge point.

  20. Cross spectral energy method for damage assessment of the cable-stayed bridge under operational conditions

    Institute of Scientific and Technical Information of China (English)

    Yang Hezhen; Li Huajun

    2008-01-01

    The new cross spectral energy method (CSEM) is proposed for maintaining cable-stayed bridge safety by the measurable output-only vibration response.Damage assessment of real structures is limited by a series of problems such as unknown ambient excitation forces, errors introduced by system identification,incomplete dynamic measurements, etc.Thus the methodology based on cross spectral energy of each substructure member is derived to meet these challenges.The novel damage index does not require any modal or parameter identification technology.It can be calculated directly from vibration test data.In order to evaluate the efficiency of the presented methodology, a three dimensional (3D) actual cable-stayed bridge model with one or more damaged positions under operational conditions was studied.In order to testify the reliability of damage detection method, the response data was polluted by the random noise.It is proved that the proposed method can successfully localize all damage cases even in noisy data.With the help of examples, the CSEM can potentially be applied as a nondestructive evaluation technique (NDT) for on-line health monitoring of cable-stayed bridges with minimum disruption of its operations.

  1. [Air conditioning units and warm air blankets in the operating room].

    Science.gov (United States)

    Kerwat, Klaus; Piechowiak, Karolin; Wulf, Hinnerk

    2013-01-01

    Nowadays almost all operating rooms are equipped with air conditioning (AC units). Their main purpose is climatization, like ventilation, moisturizing, cooling and also the warming of the room in large buildings. In operating rooms they have an additional function in the prevention of infections, especially the avoidance of postoperative wound infections. This is achieved by special filtration systems and by the creation of specific air currents. Since hypothermia is known to be an unambiguous factor for the development of postoperative wound infections, patients are often actively warmed intraoperatively using warm air blankets (forced-air warming units). In such cases it is frequently discussed whether such warm air blankets affect the performance of AC units by changing the air currents or whether, in contrast, have exactly the opposite effect. However, it has been demonstrated in numerous studies that warm air blankets do not have any relevant effect on the functioning of AC units. Also there are no indications that their use increases the rate of postoperative wound infections. By preventing the patient from experiencing hypothermia, the rate of postoperative wound infections can even be decreased thereby. © Georg Thieme Verlag Stuttgart · New York.

  2. Effect of activated sludge properties and membrane operation conditions on fouling characteristics in membrane bioreactors.

    Science.gov (United States)

    Choi, Hyeok; Zhang, Kai; Dionysiou, Dionysios D; Oerther, Daniel B; Sorial, George A

    2006-06-01

    Biofouling control is considered to be a major challenge in operating membrane bioreactors (MBRs) for the treatment of wastewater. This study examined the impact of biological, chemical, and physical properties of activated sludge on membrane filtration performance in laboratory-scale MBRs. Sludges with different microbial communities were produced using pseudo-continuous stirred-tank reactors and pseudo-plug flow reactors treating a synthetic paper mill wastewater. Various filtration resistances were used to investigate membrane fouling characteristics, and molecular biology tools targeting 16S ribosomal DNA gene sequences were used to identify predominant bacterial populations in the sludges or attached to the fouled membranes. Filtration experiments using axenic cultures of Escherichia coli, Acinetobacter calcoaceticus, and Gordonia amarae were also performed to better understand the initiation and development of biofouling. The results showed that the tendency of membranes to biofoul depended upon membrane operating conditions as well as the properties of the activated sludge in the MBR systems. Specific bacterial populations, which were not dominant in the activated sludges, were selectively accumulated on the membrane surface leading to the development of irreversible biofouling.

  3. Contaminant removal in septage treatment with vertical flow constructed wetlands operated under batch flow conditions.

    Science.gov (United States)

    Jong, Valerie Siaw Wee; Tang, Fu Ee

    2016-01-01

    Individual septic tanks are the most common means of on-site sanitation in Malaysia, but they result in a significant volume of septage. A two-staged vertical flow constructed wetlands (VFCWs) system for the treatment of septage was constructed and studied in Sarawak, Malaysia. Raw septage was treated in the first stage wetlands, and the resulting percolate was fed onto the second stage wetlands for further treatment. Here, the effects of a batch loading regime on the contaminant removal efficiency at the second stage wetlands, which included palm kernel shell within their filter substrate, are presented. The batch loading regime with pond:rest (P:R) period of 1:1, 2:2 and 3:3 (day:day) was studied. The improvement of the effluent redox condition was evident with P:R = 3:3, resulting in excellent organic matters (chemical oxygen demand and biochemical oxygen demand) and nitrogen reduction. The bed operated with P:R = 1:1 experienced constant clogging, with a water layer observed on the bed surface. For the P:R = 3:3 regime, the dissolved oxygen profile was not found to decay drastically after 24 hours of ponding, suggesting that the biodegradation mainly occurred during the first day. The study results indicate that a suitable application regime with an adequate rest period is important in VFCWs to ensure efficient operation.

  4. Unsteady Pressure Measurements around Rotor of an Axial Flow Fan under Stable and Unstable Operating Conditions

    Science.gov (United States)

    Shin, You Hwan; Kim, Kwang Ho; Kang, Chang Sik

    This study presents some measurement results on the unsteady pressure fields around rotor under stable and unstable operating conditions of an axial flow fan. The unsteady static pressure of rotor passage was measured by using high frequency pressure transducers mounted on the casing wall. The measurements on the unsteady total pressure at rotor inlet and outlet were also conducted with specially designed high frequency total pressure probe. Double Phase-Locked Ensemble Averaging Technique was used for analysis of pressure fluctuations around the rotor at rotating stall onset point. From the results, the unsteady pressure fields during stable and unstable operations of the axial fan were investigated and compared with each other. Particularly one period of rotating stall could be divided into two regions, stalled flow and unstalled flow region respectively. Furthermore the former could be also classified into two zones, bubbled and disturbed region by their features. The flow characteristics for each zone were described in detail and the static and total pressure fields were also analyzed in terms of the pressure distribution along pressure side and suction side on the blade tip profile.

  5. Main mechanisms of material properties degradation under reactor pressure vessel operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Karzov, Georgy; Timofeev, Boris [Central Research Inst. of Structural Materials ' prometey' , St. Petersburg (Russian Federation)

    1999-07-01

    In the process of NPP equipment operation materials are subjected to a prolonged influence of loads, associated with the variation of inner pressure and temperature under various conditions. Each equipment element damage is associated with some material fracture mechanism. For NPP equipment the mechanisms of irreversible damage accumulation are related with: irradiation embrittlement, thermal and strain aging, fatigue damages from mechanical and thermal loading, stress corrosion and fatigue corrosion, creep and thermal relaxation stresses, erosion and weak, thermal shock. The basic tasks of specialists working in the sphere of the provision of reliability and service life of nuclear power equipment are not only the determination of the main mechanisms of damages and reasons of their appearance, but also the study of methods which would permit to control these properties completely. By giving some examples of Russian NPP equipment with VVER-440 and VVER-1000 reactors the paper presents most typical degradation mechanisms of equipment material properties, including weldments, in the process of operation and methods to recover by using various technological means. (author)

  6. Flexible operation strategy for environment control system in abnormal supply power condition

    Science.gov (United States)

    Liping, Pang; Guoxiang, Li; Hongquan, Qu; Yufeng, Fang

    2017-04-01

    This paper establishes an optimization method that can be applied to the flexible operation of the environment control system in an abnormal supply power condition. A proposed conception of lifespan is used to evaluate the depletion time of the non-regenerative substance. The optimization objective function is to maximize the lifespans. The optimization variables are the allocated powers of subsystems. The improved Non-dominated Sorting Genetic Algorithm is adopted to obtain the pareto optimization frontier with the constraints of the cabin environmental parameters and the adjustable operating parameters of the subsystems. Based on the same importance of objective functions, the preferred power allocation of subsystems can be optimized. Then the corresponding running parameters of subsystems can be determined to ensure the maximum lifespans. A long-duration space station with three astronauts is used to show the implementation of the proposed optimization method. Three different CO2 partial pressure levels are taken into consideration in this study. The optimization results show that the proposed optimization method can obtain the preferred power allocation for the subsystems when the supply power is at a less-than-nominal value. The method can be applied to the autonomous control for the emergency response of the environment control system.

  7. 76 FR 66660 - Special Conditions: Gulfstream Aerospace LP (GALP) Model G280 Airplane, Operation Without Normal...

    Science.gov (United States)

    2011-10-27

    ... G280 Airplane, Operation Without Normal Electrical Power AGENCY: Federal Aviation Administration (FAA... design feature associated with operation without normal electrical power. The applicable airworthiness... have a novel or unusual design feature associated with operation without normal electrical power....

  8. 78 FR 73112 - Monitoring System Conditions-Transmission Operations Reliability Standards; Interconnection...

    Science.gov (United States)

    2013-12-05

    ..., performance, and maintenance of real-time monitoring and analysis capabilities for reliability coordinators... Reliability Standards; Interconnection Reliability Operations and Coordination Reliability Standards AGENCY... Transmission Operations and Interconnection Reliability Operations and Coordination Reliability Standards...

  9. Assessment of biogas production from MBT waste under different operating conditions

    DEFF Research Database (Denmark)

    Pantini, Sara; Verginelli, Jason; Lombardi, Francesco

    2015-01-01

    In this work, the influence of different operating conditions on the biogas production from mechanically-. biologically treated (MBT) wastes is investigated. Specifically, different lab-scale anaerobic tests varying the water content (26-43% w/w up to 75% w/w), the temperature (from 20 to 25...... degrees C up to 55 degrees C) and the amount of inoculum have been performed on waste samples collected from a full-scale Italian MBT plant. For each test, the gas generation yield and, where applicable, the first-order gas generation rates were determined. Nearly all tests were characterised by a quite...... to deplete the MBT waste gas generation capacity were observed. At these test conditions, the effect of temperature became evident, leading to gas generation rates of 0.007 d(-1) at room temperature that increased to 0.03-0.05 d(-1) at 37 degrees C and to 0.04-0.11 d(-1) at 55 degrees C. Overall...

  10. Operational data and thermodynamic modeling of a Stirling-dish demonstration installation in desert conditions

    Science.gov (United States)

    Nilsson, Martin; Jamot, Jakob; Malm, Tommy

    2017-06-01

    To field test its Stirling-dish unit, Cleanergy AB of Sweden in Q1 2015 built a ten unit demo park in Dubai. The first STE (Solar Thermal Energy) generation of its Stirling genset, the C11S, had at its core an 11 kWel Stirling engine/generator combination. The genset was mated with a parabolic concentrator developed for the genset by a supplier. Local weather conditions in Dubai provide opportunities to test performance in an environment with high insolation and high ambient temperature. In addition, the conditions in Dubai are windy, salty, humid and dusty, historically challenging for solar technologies [1]. In Q1 2016 one of the C11S Stirling-dish units was replaced by the first prototype of Cleanergy's second generation Stirling genset, the Sunbox, and an in-house developed parabolic concentrator. Operational data from field testing during the spring of 2016 are presented and discussed and show the large performance improvement achieved with the Sunbox unit.

  11. Optimizing operating conditions and electrochemical characterization of glucose-gluconate alkaline fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Pasta, M. [Universita degli Studi di Milano, Dipartimento di Chimica Inorganica, Metallorganica e Analitica ' ' Lamberto Malatesta' ' , Via Venezian 21, 20133 Milano (Italy); Department of Material Science and Engineering, Stanford University, Stanford, CA 94305 (United States); La Mantia, F. [Department of Material Science and Engineering, Stanford University, Stanford, CA 94305 (United States); Ruffo, R.; Mari, C.M. [Universita degli Studi di Milano-Bicocca, Dipartmento di Scienza dei Materiali, Via Cozzi 53, 20125 Milano (Italy); Peri, F. [Universita degli Studi di Milano-Bicocca, Dipartimento di Biotecnologia e Bioscienze, P.zza della Scienza 2, 20126 Milano (Italy); Pina, C. Della [Universita degli Studi di Milano, Dipartimento di Chimica Inorganica, Metallorganica e Analitica ' ' Lamberto Malatesta' ' , Via Venezian 21, 20133 Milano (Italy)

    2011-02-01

    The direct oxidation of glucose to produce electrical energy has been widely investigated because of renewability, abundance, high energy density and easy handling of the carbohydrate. Most of the previous studies have been conducted in extreme conditions in order to achieve complete glucose oxidation to CO{sub 2}, neglecting the carbohydrate chemical instability that generally leads to useless by-products mixtures. The partial oxidation to gluconate, originally studied for implantable fuel cells, has the advantage of generating a commercially valuable chemical. In the present paper we optimized fuel composition and operating conditions in order to selectively oxidize glucose to gluconate, maximizing the power density output of a standard commercial platinum based anode material. A deep electrochemical characterization concerning reversible potential, cyclic voltammetry and overpotential measurements have been carried out at 25 C in the D-(+)-glucose concentration range 1.0 x 10{sup -2} to 1.0 M. NMR and EIS investigation clarify the role of the buffer in enhancing the electrochemical performance. (author)

  12. A diagnostic signal selection scheme for planetary gearbox vibration monitoring under non-stationary operational conditions

    Science.gov (United States)

    Feng, Ke; Wang, KeSheng; Zhang, Mian; Ni, Qing; Zuo, Ming J.

    2017-03-01

    The planetary gearbox, due to its unique mechanical structures, is an important rotating machine for transmission systems. Its engineering applications are often in non-stationary operational conditions, such as helicopters, wind energy systems, etc. The unique physical structures and working conditions make the vibrations measured from planetary gearboxes exhibit a complex time-varying modulation and therefore yield complicated spectral structures. As a result, traditional signal processing methods, such as Fourier analysis, and the selection of characteristic fault frequencies for diagnosis face serious challenges. To overcome this drawback, this paper proposes a signal selection scheme for fault-emphasized diagnostics based upon two order tracking techniques. The basic procedures for the proposed scheme are as follows. (1) Computed order tracking is applied to reveal the order contents and identify the order(s) of interest. (2) Vold-Kalman filter order tracking is used to extract the order(s) of interest—these filtered order(s) constitute the so-called selected vibrations. (3) Time domain statistic indicators are applied to the selected vibrations for faulty information-emphasized diagnostics. The proposed scheme is explained and demonstrated in a signal simulation model and experimental studies and the method proves to be effective for planetary gearbox fault diagnosis.

  13. Gas chromatographic quantitative analysis of methanol in wine: operative conditions, optimization and calibration model choice.

    Science.gov (United States)

    Caruso, Rosario; Gambino, Grazia Laura; Scordino, Monica; Sabatino, Leonardo; Traulo, Pasqualino; Gagliano, Giacomo

    2011-12-01

    The influence of the wine distillation process on methanol content has been determined by quantitative analysis using gas chromatographic flame ionization (GC-FID) detection. A comparative study between direct injection of diluted wine and injection of distilled wine was performed. The distillation process does not affect methanol quantification in wines in proportions higher than 10%. While quantification performed on distilled samples gives more reliable results, a screening method for wine injection after a 1:5 water dilution could be employed. The proposed technique was found to be a compromise between the time consuming distillation process and direct wine injection. In the studied calibration range, the stability of the volatile compounds in the reference solution is concentration-dependent. The stability is higher in the less concentrated reference solution. To shorten the operation time, a stronger temperature ramp and carrier flow rate was employed. With these conditions, helium consumption and column thermal stress were increased. However, detection limits, calibration limits, and analytical method performances are not affected substantially by changing from normal to forced GC conditions. Statistical data evaluation were made using both ordinary (OLS) and bivariate least squares (BLS) calibration models. Further confirmation was obtained that limit of detection (LOD) values, calculated according to the 3sigma approach, are lower than the respective Hubaux-Vos (H-V) calculation method. H-V LOD depends upon background noise, calibration parameters and the number of reference standard solutions employed in producing the calibration curve. These remarks are confirmed by both calibration models used.

  14. Acetylcholine release in the hippocampus during the operant conditioned reflex and the footshock stimulus in rats.

    Science.gov (United States)

    Dong, Yu; Mao, Jianjun; Shangguan, Dihua; Zhao, Rui; Liu, Guoquan

    2004-10-14

    The activity of the septo-hippocampal cholinergic pathway was investigated by measuring changes in the extracellular acetylcholine (ACh) levels in the hippocampus, by means of microdialysis, during the operant conditioned reflex and the repeated footshock stimulus. Microdialysis samplings were conducted in a Skinner box where lights were delivered as conditioned stimuli (CS) paired with footshocks as unconditioned stimuli (US). Two groups of rats were used. Extracellular ACh and choline (Ch) in samples collected at 6min intervals were assessed by high-performance liquid chromatography with electrochemical detection. The elevation of hippocampus ACh was observed in the two experimental groups. The increase in ACh during aversive stimulus (footshock) was significantly larger and was probably related to the number of footshocks. There might be moderate increase in the hippocampal ACh release during the retrieval of information. The concentration of choline showed no significant fluctuation in the two groups during the whole process. This experiment explored in more detail hippocampal cholinergic activity in relation to the two different procedures.

  15. Influence of operational conditions on biofilm specific activity of an anaerobic fluidized bed reactor.

    Science.gov (United States)

    García-Morales, J L; Romero, L I; Sales, D

    2003-01-01

    A key parameter in water and wastewater treatment technology is the biomass activity in terms of substrate removal ability. The effects of organic load rate and percentage of bed expansion on biofilm specific methanogenic activity were determined in an anaerobic fluidized bed reactor treating wine-distillery wastes in the thermophilic range (55 degrees C). The proposed activity tests are highly reproducible: an experiment with three identical tests has shown that the standard deviation with respect to the mean values is less than 3%. Specific tests are applied to measure the maximum methanogenic activities of the biomass carrier in lab-scale anaerobic biofilm reactors. These tests have been successfully applied for monitoring the support colonization process and the evolution of biofilm activity in reactors, anaerobic filter and fluidized bed, with different operating conditions. The results show a dependence between the percentage of bed expansion and the specific activity of methanogenic microbiote on biofilm. There is a relationship between the percentage of bed expansion, the sheer stress on the biofilm and the hydrodynamic conditions in the system. Initial biofilm detachment can be compensated with the increase of biomass and of its activity due to the reduction of the substrate diffusional limitations to the microorganism growth inside the support pores.

  16. OPERANT CONDITIONING OF SPINAL REFLEXES:FROM BASIC SCIENCE TO CLINICAL THERAPY

    Directory of Open Access Journals (Sweden)

    Aiko K. Thompson

    2014-03-01

    Full Text Available New appreciation of the adaptive capabilities of the nervous system, recent recognition that most spinal cord injuries are incomplete, and progress in enabling regeneration are generating growing interest in novel rehabilitation therapies. Here we review the 35-year evolution of one promising new approach, operant conditioning of spinal reflexes. This work began in the late 1970’s as basic science; its purpose was to develop and exploit a uniquely accessible model for studying the acquisition and maintenance of a simple behavior in the mammalian CNS. The model was developed first in monkeys and then in rats, mice, and humans. Studies with it showed that the ostensibly simple behavior (i.e., a larger or smaller reflex rests on a complex hierarchy of brain and spinal cord plasticity; and current investigations are delineating this plasticity and its interactions with the plasticity that supports other behaviors. In the last decade, the possible therapeutic uses of reflex conditioning have come under study, first in rats and then in humans. The initial results are very exciting, and they are spurring further studies. At the same time, the original basic science purpose and the new clinical purpose are enabling and illuminating each other in unexpected ways. The long course and current state of this work illustrate the practical importance of basic research and the valuable synergy that can develop between basic science questions and clinical needs.

  17. Tribological Evaluation of Candidate Gear Materials Operating Under Light Loads in Highly Humid Conditions

    Science.gov (United States)

    Dellacorte, Christopher; Thomas, Fransua; Leak, Olivia Ann

    2015-01-01

    A series of pin-on-disk sliding wear tests were undertaken to identify candidate materials for a pair of lightly loaded timing gears operating under highly humid conditions. The target application involves water purification and thus precludes the use of oil, grease and potentially toxic solid lubricants. The baseline sliding pair is austenitic stainless steel operating against a carbon filled polyimide. The test load and sliding speed (4.9 N, 2.7 m/s) were chosen to represent average contact conditions of the meshing gear teeth. In addition to the baseline materials, the hard superelastic NiTiNOL 60 (60NiTi) was slid against itself, against the baseline polyimide, and against 60NiTi onto which a commercially deposited dry film lubricant (DFL) was applied. The alternate materials were evaluated as potential replacements to achieve a longer wear life and improved dimensional stability for the timing gear application. An attempt was also made to provide solid lubrication to self-mated 60NiTi by rubbing the polyimide against the disk wear track outside the primary 60NiTi-60NiTi contact, a method named stick or transfer-film lubrication. The selected test conditions gave repeatable friction and wear data and smooth sliding surfaces for the baseline materials similar to those in the target application. Friction and wear for self-mated stainless steel were high and erratic. Self-mated 60NiTi gave acceptably low friction (approx. 0.2) and modest wear but the sliding surfaces were rough and potentially unsuitable for the gear application. Tests in which 60NiTi pins were slid against DFL coated 60NiTi and DFL coated stainless steel gave low friction and long wear life. The use of stick lubrication via the secondary polyimide pin provided effective transfer film lubrication to self-mated 60NiTi tribological specimens. Using this approach, friction levels were equal or lower than the baseline polyimide-stainless combination and wear was higher but within data scatter observed

  18. Protein purification using chromatography: selection of type, modelling and optimization of operating conditions.

    Science.gov (United States)

    Asenjo, J A; Andrews, B A

    2009-01-01

    To achieve a high level of purity in the purification of recombinant proteins for therapeutic or analytical application, it is necessary to use several chromatographic steps. There is a range of techniques available including anion and cation exchange, which can be carried out at different pHs, hydrophobic interaction chromatography, gel filtration and affinity chromatography. In the case of a complex mixture of partially unknown proteins or a clarified cell extract, there are many different routes one can take in order to choose the minimum and most efficient number of purification steps to achieve a desired level of purity (e.g. 98%, 99.5% or 99.9%). This review shows how an initial 'proteomic' characterization of the complex mixture of target protein and protein contaminants can be used to select the most efficient chromatographic separation steps in order to achieve a specific level of purity with a minimum number of steps. The chosen methodology was implemented in a computer- based Expert System. Two algorithms were developed, the first algorithm was used to select the most efficient purification method to separate a protein from its contaminants based on the physicochemical properties of the protein product and the protein contaminants and the second algorithm was used to predict the number and concentration of contaminants after each separation as well as protein product purity. The application of the Expert System approach was experimentally tested and validated with a mixture of four proteins and the experimental validation was also carried out with a supernatant of Bacillus subtilis producing a recombinant beta-1,3-glucanase. Once the type of chromatography is chosen, optimization of the operating conditions is essential. Chromatographic elution curves for a three-protein mixture (alpha-lactoalbumin, ovalbumin and beta-lactoglobulin), carried out under different flow rates and ionic strength conditions, were simulated using two different mathematical

  19. Experimental investigation of mixing of non-isothermal water streams at BWR operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Bergagio, Mattia, E-mail: bergagio@kth.se [AlbaNova University Center, Nuclear Reactor Technology Division, Department of Physics, Royal Institute of Technology, 106 91 Stockholm (Sweden); Anglart, Henryk, E-mail: henryk@kth.se [AlbaNova University Center, Nuclear Reactor Technology Division, Department of Physics, Royal Institute of Technology, 106 91 Stockholm (Sweden); Institute of Heat Engineering, Warsaw University of Technology, 21/25 Nowowiejska Street, 00-665 Warsaw (Poland)

    2017-06-15

    Highlights: • Temperatures are measured in the presence of mixing at BWR operating conditions. • The thermocouple support is moved along a pattern to extend the measurement region. • Uncertainty of 1.58 K for temperatures acquired at 1000 Hz. • Momenta of the hot streams and thermal stratification affect the data examined. • Unconventional spectral analysis is required to further study the data collected. - Abstract: In this experimental investigation, wall surface temperatures have been measured during mixing of three water streams in the annular gap between two coaxial stainless-steel tubes. The inner tube, with an outer diameter of 35 mm and a thickness of 5 mm, holds six K-type, ungrounded thermocouples with a diameter of 0.5 mm, which measured surface temperatures with a sampling rate of either 100 Hz or 1000 Hz. The tube was rotated from 0 to 360° and moved in a range of 387 mm in the axial direction to allow measurements of surface temperatures in the whole mixing region. The outer tube has an inner diameter of 80 mm and a thickness of 10 mm to withstand a water pressure of 9 MPa. A water stream at a temperature of either 333 K or 423 K and a Reynolds number between 1657 and 8410 rose vertically in the annular gap and mixed with two water streams at a temperature of 549 K and a Reynolds number between 3.56 × 10{sup 5} and 7.11 × 10{sup 5}. These two water streams entered the annulus radially on the same axial level, 180° apart. Water pressure was kept at 7.2 MPa. Temperature recordings were performed at five axial and eight azimuthal locations, for each set of boundary conditions. Each recording lasted 120 s to provide reliable data on the variance, intermittency and frequency of the surface temperature time series at hand. Thorough calculations indicate that the uncertainty in the measured temperature is of 1.58 K. The mixing region extends up to 0.2 m downward of the hot inlets. In most cases, measurements indicate non-uniform mixing in the

  20. Preliminary Two-Phase Terry Turbine Nozzle Models for RCIC Off-Design Operation Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Haihua [Idaho National Lab. (INL), Idaho Falls, ID (United States); O' Brien, James [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2017-06-12

    This report presents the effort to extend the single-phase analytical Terry turbine model to cover two-phase off-design conditions. The work includes: (1) adding well-established two-phase choking models – the Isentropic Homogenous Equilibrium Model (IHEM) and Moody’s model, and (2) theoretical development and implementation of a two-phase nozzle expansion model. The two choking models provide bounding cases for the two-phase choking mass flow rate. The new two-phase Terry turbine model uses the choking models to calculate the mass flow rate, the critical pressure at the nozzle throat, and steam quality. In the divergent stage, we only consider the vapor phase with a similar model for the single-phase case by assuming that the liquid phase would slip along the wall with a much slower speed and will not contribute the impulse on the rotor. We also modify the stagnation conditions according to two-phase choking conditions at the throat and the cross-section areas for steam flow at the nozzle throat and at the nozzle exit. The new two-phase Terry turbine model was benchmarked with the same steam nozzle test as for the single-phase model. Better agreement with the experimental data is observed than from the single-phase model. We also repeated the Terry turbine nozzle benchmark work against the Sandia CFD simulation results with the two-phase model for the pure steam inlet nozzle case. The RCIC start-up tests were simulated and compared with the single-phase model. Similar results are obtained. Finally, we designed a new RCIC system test case to simulate the self-regulated Terry turbine behavior observed in Fukushima accidents. In this test, a period inlet condition for the steam quality varying from 1 to 0 is applied. For the high quality inlet period, the RCIC system behaves just like the normal operation condition with a high pump injection flow rate and a nominal steam release rate through the turbine, with the net addition of water to the primary system; for

  1. Operant serial feature-positive conditional discrimination with composite features and different topography responses

    Directory of Open Access Journals (Sweden)

    J.L.O. Bueno

    2008-02-01

    Full Text Available In a serial feature-positive conditional discrimination procedure the properties of a target stimulus A are defined by the presence or not of a feature stimulus X preceding it. In the present experiment, composite features preceded targets associated with two different topography operant responses (right and left bar pressing; matching and non-matching-to-sample arrangements were also used. Five water-deprived Wistar rats were trained in 6 different trials: X-R®Ar and X-L®Al, in which X and A were same modality visual stimuli and the reinforcement was contingent to pressing either the right (r or left (l bar that had the light on during the feature (matching-to-sample; Y-R®Bl and Y-L®Br, in which Y and B were same modality auditory stimuli and the reinforcement was contingent to pressing the bar that had the light off during the feature (non-matching-to-sample; A- and B- alone. After 100 training sessions, the animals were submitted to transfer tests with the targets used plus a new one (auditory click. Average percentages of stimuli with a response were measured. Acquisition occurred completely only for Y-L®Br+; however, complex associations were established along training. Transfer was not complete during the tests since concurrent effects of extinction and response generalization also occurred. Results suggest the use of both simple conditioning and configurational strategies, favoring the most recent theories of conditional discrimination learning. The implications of the use of complex arrangements for discussing these theories are considered.

  2. Solar desiccant air-conditioning. Practical experience regarding operation and performance

    Energy Technology Data Exchange (ETDEWEB)

    Haller, A.; Trinkl, C.; Wittmann, R.; Zoerner, W. [Ingolstadt Univ. of Applied Sciences (Germany). Kompetenzzentrum Solartechnik; Hanby, V. [De Montfort Univ., Leicester (GB). Inst. of Energy and Sustainable Development (IESD)

    2007-07-01

    The Kompetenzzentrum Solartechnik of Ingolstadt University of Applied Sciences (Centre of Excellence for Solar Engineering) investigates the renewable-only based HVAC system of a multipurpose building. The 10.000 m{sup 2} gross floor area building is part of the biggest logistic-centre in the region serving the AUDI automobile production facilities. On the one hand, the investigation is supposed to demonstrate the potential of solar-assisted cooling, on the other hand, the monitoring, financed by the Bavarian Ministry of Environmental Affairs, focuses on the total energy balance of the building and the various innovative building technologies. Next to a ground source heat pump plant for base-load heating and cooling, the building is equipped with two arrays of solar-thermal flat-plate collectors (100 m{sup 2} of Conergy, Germany, and 180 m{sup 2} of Solahart, Australia) and a desiccant air-conditioning system (DEC, WOLF Anlagen-Technik, Germany). This consists of two plants with an air flow of 8.000 m{sup 3}/h and a nominal cooling capacity of 42 kW each. One of the two plants is monitored. The plant itself is considered a black box in a first approach, i.e. all incoming and outgoing energy flows and the air condition are measured. Apart from the investigation of the performance of the solar-assisted air-conditioning system, the feasibility of DEC-operation using flat-plate collectors available on the market is investigated. (orig.)

  3. A mathematical model for removal of human pathogenic viruses and bacteria by slow sand filtration under variable operational conditions

    NARCIS (Netherlands)

    Schijven, J.F.; Berg, H.H.J.L. van den; Colin, M.; Dullemont, Y.; Hijnen, W.A.M.; Magic-Knezev, A.; Oorthuizen, W.A.; Wubbels, G.

    2013-01-01

    Slow sand filtration (SSF) in drinking water production removes pathogenic microorganisms, but detection limits and variable operational conditions complicate assessment of removal efficiency. Therefore, amodel was developed to predict removal ofhuman pathogenic viruses and bacteria as a function of

  4. Modeling the Relationship between Vibration Features and Condition Parameters Using Relevance Vector Machines for Health Monitoring of Rolling Element Bearings under Varying Operation Conditions

    Directory of Open Access Journals (Sweden)

    Lei Hu

    2015-01-01

    Full Text Available Rotational speed and load usually change when rotating machinery works. Both this kind of changing operational conditions and machine fault could make the mechanical vibration characteristics change. Therefore, effective health monitoring method for rotating machinery must be able to adjust during the change of operational conditions. This paper presents an adaptive threshold model for the health monitoring of bearings under changing operational conditions. Relevance vector machines (RVMs are used for regression of the relationships between the adaptive parameters of the threshold model and the statistical characteristics of vibration features. The adaptive threshold model is constructed based on these relationships. The health status of bearings can be indicated via detecting whether vibration features exceed the adaptive threshold. This method is validated on bearings running at changing speeds. The monitoring results show that this method is effective as long as the rotational speed is higher than a relative small value.

  5. Hippocampal Homer1 levels influence motivational behavior in an operant conditioning task.

    Directory of Open Access Journals (Sweden)

    Klaus V Wagner

    Full Text Available Loss of motivation and learning impairments are commonly accepted core symptoms of psychiatric disorders such as depression and schizophrenia. Reward-motivated learning is dependent on the hippocampal formation but the molecular mechanisms that lead to functional incentive motivation in this brain region are still largely unknown. Recent evidence implicates neurotransmission via metabotropic glutamate receptors and Homer1, their interaction partner in the postsynaptic density, in drug addiction and motivational learning. As previous reports mainly focused on the prefrontal cortex and the nucleus accumbens, we now investigated the role of hippocampal Homer1 in operant reward learning in the present study. We therefore tested either Homer1 knockout mice or mice that overexpress Homer1 in the hippocampus in an operant conditioning paradigm. Our results show that deletion of Homer1 leads to a diverging phenotype that either displays an inability to perform the task or outstanding hyperactivity in both learning and motivational sessions. Due to the apparent bimodal distribution of this phenotype, the overall effect of Homer1 deletion in this paradigm is not significantly altered. Overexpression of hippocampal Homer1 did not lead to a significantly altered learning performance in any stage of the testing paradigm, yet may subtly contribute to emerging motivational deficits. Our results indicate an involvement of Homer1-mediated signaling in the hippocampus in motivation-based learning tasks and encourage further investigations regarding the specific molecular underpinnings of the phenotypes observed in this study. We also suggest to cautiously interpret the results of this and other studies regarding the phenotype following Homer1 manipulations in animals, since their behavioral phenotype appears to be highly diverse. Future studies would benefit from larger group sizes that would allow splitting the experimental groups in responders and non-responders.

  6. The Annotation, Mapping, Expression and Network (AMEN suite of tools for molecular systems biology

    Directory of Open Access Journals (Sweden)

    Primig Michael

    2008-02-01

    Full Text Available Abstract Background High-throughput genome biological experiments yield large and multifaceted datasets that require flexible and user-friendly analysis tools to facilitate their interpretation by life scientists. Many solutions currently exist, but they are often limited to specific steps in the complex process of data management and analysis and some require extensive informatics skills to be installed and run efficiently. Results We developed the Annotation, Mapping, Expression and Network (AMEN software as a stand-alone, unified suite of tools that enables biological and medical researchers with basic bioinformatics training to manage and explore genome annotation, chromosomal mapping, protein-protein interaction, expression profiling and proteomics data. The current version provides modules for (i uploading and pre-processing data from microarray expression profiling experiments, (ii detecting groups of significantly co-expressed genes, and (iii searching for enrichment of functional annotations within those groups. Moreover, the user interface is designed to simultaneously visualize several types of data such as protein-protein interaction networks in conjunction with expression profiles and cellular co-localization patterns. We have successfully applied the program to interpret expression profiling data from budding yeast, rodents and human. Conclusion AMEN is an innovative solution for molecular systems biological data analysis freely available under the GNU license. The program is available via a website at the Sourceforge portal which includes a user guide with concrete examples, links to external databases and helpful comments to implement additional functionalities. We emphasize that AMEN will continue to be developed and maintained by our laboratory because it has proven to be extremely useful for our genome biological research program.

  7. Exposure assessment using human biomonitoring for glyphosate and fluroxypyr users in amenity horticulture.

    Science.gov (United States)

    Connolly, Alison; Jones, Kate; Galea, Karen S; Basinas, Ioannis; Kenny, Laura; McGowan, Padraic; Coggins, Marie

    2017-08-01

    Pesticides and their potential adverse health effects are of great concern and there is a dearth of knowledge regarding occupational exposure to pesticides among amenity horticulturalists. This study aims to measure occupational exposures to amenity horticuturalists using pesticides containing the active ingredients, glyphosate and fluroxypyr by urinary biomonitoring. A total of 40 work tasks involving glyphosate and fluroxypyr were surveyed over the period of June - October 2015. Workers used a variety of pesticide application methods; manual knapsack sprayers, controlled droplet applicators, pressurised lance applicators and boom sprayers. Pesticide concentrations were measured in urine samples collected pre and post work tasks using liquid chromatography tandem mass spectrometry (LC-MS/MS). Differences in pesticide urinary concentrations pre and post work task, and across applications methods were analysed using paired t-tests and linear regression. Pesticide urinary concentrations were higher than those reported for environmental exposures and comparable to those reported in some agricultural studies. Log-transformed pesticide concentrations were statistically significantly higher in post-work samples compared to those in pre-work samples (paired t-test, p<0.001; for both μgL(-1) and μmol/mol creatinine). Urinary pesticide concentrations in post-work samples had a geometric mean (geometric standard deviation) of 0.66 (1.11) μgL(-1) for glyphosate and 0.29 (1.69) μgL(-1) for fluroxypyr. Linear regression revealed a statistically significant positive association to exist between the time-interval between samples and the log-transformed adjusted (i.e. post- minus pre-task) pesticide urinary concentrations (β=0.0039; p<0.0001). Amenity horticulturists can be exposed to pesticides during tasks involving these products. Further research is required to evaluate routes of exposure among this occupational group. Crown Copyright © 2017. Published by Elsevier Gmb

  8. Computational Fluid Dynamics Based Investigation of Sensitivity of Furnace Operational Conditions to Burner Flow Controls

    Energy Technology Data Exchange (ETDEWEB)

    Marc Cremer; Kirsi St. Marie; Dave Wang

    2003-04-30

    This is the first Semiannual Technical Report for DOE Cooperative Agreement No: DE-FC26-02NT41580. The goal of this project is to systematically assess the sensitivity of furnace operational conditions to burner air and fuel flows in coal fired utility boilers. Our approach is to utilize existing baseline furnace models that have been constructed using Reaction Engineering International's (REI) computational fluid dynamics (CFD) software. Using CFD analyses provides the ability to carry out a carefully controlled virtual experiment to characterize the sensitivity of NOx emissions, unburned carbon (UBC), furnace exit CO (FECO), furnace exit temperature (FEGT), and waterwall deposition to burner flow controls. The Electric Power Research Institute (EPRI) is providing co-funding for this program, and instrument and controls experts from EPRI's Instrument and Controls (I&C) Center are active participants in this project. This program contains multiple tasks and good progress is being made on all fronts. A project kickoff meeting was held in conjunction with NETL's 2002 Sensors and Control Program Portfolio Review and Roadmapping Workshop, in Pittsburgh, PA during October 15-16, 2002. Dr. Marc Cremer, REI, and Dr. Paul Wolff, EPRI I&C, both attended and met with the project COR, Susan Maley. Following the review of REI's database of wall-fired coal units, the project team selected a front wall fired 150 MW unit with a Riley Low NOx firing system including overfire air for evaluation. In addition, a test matrix outlining approximately 25 simulations involving variations in burner secondary air flows, and coal and primary air flows was constructed. During the reporting period, twenty-two simulations have been completed, summarized, and tabulated for sensitivity analysis. Based on these results, the team is developing a suitable approach for quantifying the sensitivity coefficients associated with the parametric tests. Some of the results of the CFD

  9. Harmonic maps on amenable groups and a diffusive lower bound for random walks

    CERN Document Server

    Lee, James R

    2009-01-01

    We prove that on any infinite, connected, locally finite, transitive graph G, the probability of the random walk being within $\\eps \\sqrt{t}$ of the origin after t steps is at most $O(\\eps)$. A similar statement holds for finite graphs, up to the relaxation time of the walk. Our approach uses non-constant equivariant harmonic mappings taking values in a Hilbert space. For the special case of discrete, amenable groups, we present a more explicit proof of the Mok-Korevaar-Schoen theorem on existence of such harmonic maps by constructing them from the heat flow on a Folner set.

  10. A Two-Sector Growth Model with Endogenous Human Capital and Amenities

    Directory of Open Access Journals (Sweden)

    Wei-Bin Zhang

    2009-01-01

    Full Text Available This paper examines issues related to urbanization with labour migration. The main departures from the traditional approaches to dynamics of economic structures are that the paper uses an alternative approach to consumer behaviour and introduces human capital accumulation via learning by doing. The model describes dynamic interactions among agricultural and industrial production, rural and urban amenities, distribution of production factors and preferences with endogenous capital and human capital accumulation. We show that the dynamic system may have either a single or multiple equilibrium points, depending upon returns to scale in the two sectors. We also examined effects of changes in some parameters.

  11. Hydrothermal Testing of K Basin Sludge and N Reactor Fuel at Sludge Treatment Project Operating Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Delegard, Calvin H.; Schmidt, Andrew J.; Thornton, Brenda M.

    2007-03-30

    The Sludge Treatment Project (STP), managed for the U. S. DOE by Fluor Hanford (FH), was created to design and operate a process to eliminate uranium metal from K Basin sludge prior to packaging for Waste Isolation Pilot Plant (WIPP). The STP process uses high temperature liquid water to accelerate the reaction, produce uranium dioxide from the uranium metal, and safely discharge the hydrogen. Under nominal process conditions, the sludge will be heated in pressurized water at 185°C for as long as 72 hours to assure the complete reaction (corrosion) of up to 0.25-inch diameter uranium metal pieces. Under contract to FH, the Pacific Northwest National Laboratory (PNNL) conducted bench-scale testing of the STP hydrothermal process in November and December 2006. Five tests (~50 ml each) were conducted in sealed, un-agitated reaction vessels under the hydrothermal conditions (e.g., 7 to 72 h at 185°C) of the STP corrosion process using radioactive sludge samples collected from the K East Basin and particles/coupons of N Reactor fuel also taken from the K Basins. The tests were designed to evaluate and understand the chemical changes that may be occurring and the effects that any changes would have on sludge rheological properties. The tests were not designed to evaluate engineering aspects of the process. The hydrothermal treatment affected the chemical and physical properties of the sludge. In each test, significant uranium compound phase changes were identified, resulting from dehydration and chemical reduction reactions. Physical properties of the sludge were significantly altered from their initial, as-settled sludge values, including, shear strength, settled density, weight percent water, and gas retention.

  12. Optimization of operating conditions of distillation columns: an energy saving option in refinery industry

    Directory of Open Access Journals (Sweden)

    Alireza Fazlali

    2010-01-01

    Full Text Available While energy prices continue to climb, it conservation remains the prime concern for process industries. The daily growth of energy consumption throughout the world and the real necessity of providing it, shows that optimization of energy generation and consumption units is an economical and sometimes vital case. Hence, the optimization of a petroleum refinery is aimed towards great production and an increase in quality. In this research, the atmospheric distillation unit of the Iran-Arak-Shazand petroleum refinery was subject to optimization efforts. It was performed by the means of using a simulator with the aim to earn more overhead products. In the next step the optimization results from the simulators were carried out in the real world, at the above mentioned unit. Results demonstrate that the changes in the real operating conditions increase the overhead products with desirable quality. Finally, a net economical balance between the increments of the overhead products and the energy consumption shows an energy saving in this refinery.

  13. Predictions of structural integrity of steam generator tubes under normal operating, accident, an severe accident conditions

    Energy Technology Data Exchange (ETDEWEB)

    Majumdar, S. [Argonne National Lab., IL (United States)

    1997-02-01

    Available models for predicting failure of flawed and unflawed steam generator tubes under normal operating, accident, and severe accident conditions are reviewed. Tests conducted in the past, though limited, tended to show that the earlier flow-stress model for part-through-wall axial cracks overestimated the damaging influence of deep cracks. This observation was confirmed by further tests at high temperatures, as well as by finite-element analysis. A modified correlation for deep cracks can correct this shortcoming of the model. Recent tests have shown that lateral restraint can significantly increase the failure pressure of tubes with unsymmetrical circumferential cracks. This observation was confirmed by finite-element analysis. The rate-independent flow stress models that are successful at low temperatures cannot predict the rate-sensitive failure behavior of steam generator tubes at high temperatures. Therefore, a creep rupture model for predicting failure was developed and validated by tests under various temperature and pressure loadings that can occur during postulated severe accidents.

  14. Is fumigation enough for air conditioning units in operation theatres and Intensive care units?

    Directory of Open Access Journals (Sweden)

    Anasua Deb

    2016-05-01

    Full Text Available Background: Strict asepsis is necessary in operating theatres (OT and intensive care units (ICU as the patients undergo invasive procedures. The filters of contaminated air conditioning (AC units provide a niche for proliferation of fungi and production of fungal spores. Methods: The routine procedure for maintenance of sterile atmosphere in our hospital, i.e. fumigation and mopping walls with disinfectants often fail to address these fungal spores of the AC filters. We therefore carried out a surveillance of the ACs in ICUs and OTs to find the level of contamination with fungal spores and also to improvise on intervention strategies to tackle the problem. Over 3 months period, 34 ACs from 7 OTs and 2 ICUs were screened by taking 2 swabs from each AC which were then tested for the presence of fungal spores as per standard methods. Results: The contamination rate was 88.2% before fumigation and 76.9% after fumigation. The fungal spore contamination rate was reduced to 20% (1 out of 5 ACs after servicing of the ACs was done. Aspergillus spp. was the most common fungal isolate. Conclusion: Based on the observations, we recommend regular servicing of the ACs as well as wet mopping of the ducts with sporicidal solution at regular intervals. [Int J Res Med Sci 2016; 4(5.000: 1583-1589

  15. High Pressure Compression-Molding of α-Cellulose and Effects of Operating Conditions

    Directory of Open Access Journals (Sweden)

    Antoine Rouilly

    2013-05-01

    Full Text Available Commercial α-cellulose was compression-molded to produce 1A dog-bone specimens under various operating conditions without any additive. The resulting agromaterials exhibited a smooth, plastic-like surface, and constituted a suitable target as replacement for plastic materials. Tensile and three-points bending tests were conducted according to ISO standards related to the evaluation of plastic materials. The specimens had strengths comparable to classical petroleum-based thermoplastics. They also exhibited high moduli, which is characteristic of brittle materials. A higher temperature and higher pressure rate produced specimens with higher mechanical properties while low moisture content produced weaker specimens. Generally, the strong specimen had higher specific gravity and lower moisture content. However, some parameters did not follow the general trend e.g., thinner specimen showed much higher Young’s Modulus, although their specific gravity and moisture content remained similar to control, revealing a marked skin-effect which was confirmed by SEM observations.

  16. Overview of the deuterium inventory campaign in Tore Supra: Operational conditions and particle balance

    Energy Technology Data Exchange (ETDEWEB)

    Pegourie, B., E-mail: bernard.pegourie@cea.f [Association Euratom-CEA, CEA/DSM/IRFM, CEA Cadarache, F-13108 Saint-Paul-les-Durance cedex (France); Brosset, C.; Tsitrone, E.; Beaute, A.; Bremond, S.; Bucalossi, J.; Carpentier, S.; Corre, Y.; Delchambre, E.; Desgranges, C.; Devynck, P.; Douai, D.; Dunand, G.; Ekedahl, A. [Association Euratom-CEA, CEA/DSM/IRFM, CEA Cadarache, F-13108 Saint-Paul-les-Durance cedex (France); Escarguel, A. [PIIM, CNRS/Universite de Provence, F-13397 Marseille (France); Gauthier, E.; Gunn, J.P.; Hertout, P.; Hong, S.-H.; Kazarian, F. [Association Euratom-CEA, CEA/DSM/IRFM, CEA Cadarache, F-13108 Saint-Paul-les-Durance cedex (France)

    2009-06-15

    A specific experiment was performed in Tore Supra, dedicated to the search for consistency between wall inventories estimated from gas balance and post-mortem analysis and to the characterization of the D-retention mechanism. More than 160 similar discharges were performed, representing a cumulative time of 18 000 s of plasma with no intermediate conditioning procedure. The only significant operational issue was linked to the ejection of flakes from the plasma facing components, whose frequency increased dramatically during the campaign, triggering a plasma detachment phase followed by a disruption in number of cases. In-vessel inventory was increased by approx3.1 x 10{sup 24} D, and constant retention rate (approx2.3 x 10{sup 20} D/s averaged over discharge duration) was measured, with no indication of wall saturation. First measurements on dismantled tiles of the Toroidal Pump Limiter (TPL) show [D]/[C] ratios ranging from 0.04 to 0.20, on a typical thickness of 15-20 mum. Extrapolated to the whole TPL, this yields an amount of approx(1.5 +- 0.3) x 10{sup 24} D, i.e. approx50% of the estimated in-vessel inventory.

  17. Neutronics and Fuel Performance Evaluation of Accident Tolerant Fuel under Normal Operation Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Xu Wu; Piyush Sabharwall; Jason Hales

    2014-07-01

    This report details the analysis of neutronics and fuel performance analysis for enhanced accident tolerance fuel, with Monte Carlo reactor physics code Serpent and INL’s fuel performance code BISON, respectively. The purpose is to evaluate two of the most promising candidate materials, FeCrAl and Silicon Carbide (SiC), as the fuel cladding under normal operating conditions. Substantial neutron penalty is identified when FeCrAl is used as monolithic cladding for current oxide fuel. From the reactor physics standpoint, application of the FeCrAl alloy as coating layer on surface of zircaloy cladding is possible without increasing fuel enrichment. Meanwhile, SiC brings extra reactivity and the neutron penalty is of no concern. Application of either FeCrAl or SiC could be favorable from the fuel performance standpoint. Detailed comparison between monolithic cladding and hybrid cladding (cladding + coating) is discussed. Hybrid cladding is more practical based on the economics evaluation during the transition from current UO2/zircaloy to Accident Tolerant Fuel (ATF) system. However, a few issues remain to be resolved, such as the creep behavior of FeCrAl, coating spallation, inter diffusion with zirconium, etc. For SiC, its high thermal conductivity, excellent creep resistance, low thermal neutron absorption cross section, irradiation stability (minimal swelling) make it an excellent candidate materials for future nuclear fuel/cladding system.

  18. Evaluation of the performance degradation at PAFC effect of operating conditions on acid loss

    Energy Technology Data Exchange (ETDEWEB)

    Miyoshi, Hideaki; Uchida, Hiroyuki; Watanabe, Masahiro [Yamanashi Univ., Kofu (Japan)] [and others

    1996-12-31

    As a complimentary research project to the demonstration project of 5MW and 1 MW PAFC plants, the mechanism and rate of deterioration of the cells and stacks have been studied from 1995 FY conducted by NEDO, with the objective of establishing an estimation method for the service life-time of the cell stacks. As part of this project, this work has been performed to clarify basic phenomena of the performance degradation at PAFCs jointly by Yamanashi University, PAFC-TRA and PAFC manufacturers. The acid loss into exhaust gases is one of life limiting factors in PAFCs. To design the cells of long-life, it is important to estimate the phosphoric acid loss and to contrive ideas eliminating it. With the objective of obtaining basic data for simulating the acid loss in the large size cells, the effect of the operating conditions on the acid loss into exhaust gases has been studied experimentally by using a single cell with an active electrode area of 100 cm{sup 2}.

  19. Thermal Impact of Operating Conditions on the Performance of a Combined Cycle Gas Turbine

    Directory of Open Access Journals (Sweden)

    Thamir K. Ibrahim

    2012-08-01

    Full Text Available The combined cycle gas-turbine (CCGT power plant is a highly developed technology which generates electricalpower at high efficiencies. The first law of thermodynamics is used for energy analysis of the performance of theCCGT plant. The effects of varying the operating conditions (ambient temperature, compression ratio, turbine inlettemperature, isentropic compressor and turbine efficiencies, and mass flow rate of steam on the performance of theCCGT (overall efficiency and total output power were investigated. The programming of the performance model forCCGT was developed utilizing MATLAB software. The simulation results for CCGT show that the overall efficiencyincreases with increases in the compression ratio and turbine inlet temperature and with decreases in ambienttemperature. The total power output increases with increases in the compression ratio, ambient temperature, andturbine inlet temperature. The peak overall efficiency was reached with a higher compression ratio and low ambienttemperature. The overall efficiencies for CCGT were very high compared to the thermal efficiency of GT plants. Theoverall thermal efficiency of the CCGT quoted was around 57%; hence, the compression ratios, ambient temperature,turbine inlet temperature, isentropic compressor and turbine efficiencies, and mass flow rate of steam have a stronginfluence on the overall performance of the CCGT cycle.

  20. Commissioning and first operation of the pCVD diamond ATLAS Beam Conditions Monitor

    CERN Document Server

    Dobos, D

    2009-01-01

    The main aim of the ATLAS Beam Conditions Monitor is to protect the ATLAS Inner Detector silicon trackers from high radiation doses caused by LHC beam incidents, e.g. magnet failures. The BCM uses in total 16 1x1 cm2 500 μm thick polycrystalline chemical vapor deposition (pCVD) diamond sensors. They are arranged in 8 positions around the ATLAS LHC interaction point. Time difference measurements with sub nanosecond resolution are performed to distinguish between particles from a collision and spray particles from a beam incident. An abundance of the latter leads the BCM to provoke an abort of the LHC beam. A FPGA based readout system with a sampling rate of 2.56 GHz performs the online data analysis and interfaces the results to ATLAS and the beam abort system. The BCM diamond sensors, the detector modules and their readout system are described. Results of the operation with the first LHC beams are reported and results of commissioning and timing measurements (e.g. with cosmic muons) in preparation for first ...

  1. Improvement in operating conditions of coke oven batteries with long service life

    Energy Technology Data Exchange (ETDEWEB)

    Obertenev, V.N.; Bondarchuk, P.N.; Krut' ko, I.G.; Sheptovitskii, M.S.; Kaftan, Yu.S.; Shul' ga, I.V.; Vol' fovskii, A.G. (Mariupol' skii Koksokhimicheskii Zavod (USSR))

    1991-01-01

    Discusses operation of the coke oven battery No 1 in the Mariupol' coking plant constructed in 1949. Twenty-five of 69 coke oven chambers had liners deformed due to wear. In 1988-1989 a number of failures occurred due to accumulation of pyrolysis products and tar on coke oven walls. Excessive liner wear negatively influenced coking conditions (e.g. reducing the bulk density of charged coal, increasing the buildup on coke oven walls, increasing the density and viscosity of coal tar and content of solid particles in the tar). Increased viscosity and content of solid particles in the tar increased failure rates of a tar transport system. Coal tar properties in the Mariupol' plant and 8 other plants in the USSR are comparatively evaluated. Specific properties of coal tar from the Mariupol' plant and their causes were determined. On the basis of the evaluations coal tar properties were controlled by changing coal mixture composition (content of gas coal was reduced to 32% of G and GZh types). Reducing content of gas coal in the mixtures reduced coke oven failure rate, increased coke compression strength by 0.6% and reduced coke abrasion by 0.25%. 5 refs.

  2. Large-eddy simulation of propeller wake at design operating conditions

    Science.gov (United States)

    Kumar, Praveen; Mahesh, Krishnan

    2016-11-01

    Understanding the propeller wake is crucial for efficient design and optimized performance. The dynamics of the propeller wake are also central to physical phenomena such as cavitation and acoustics. Large-eddy simulation is used to study the evolution of the wake of a five-bladed marine propeller from near to far field at design operating condition. The computed mean loads and phase-averaged flow field show good agreement with experiments. The propeller wake consisting of tip and hub vortices undergoes streamtube contraction, which is followed by the onset of instabilities as evident from the oscillations of the tip vortices. Simulation results reveal a mutual induction mechanism of instability where instead of the tip vortices interacting among themselves, they interact with the smaller vortices generated by the roll-up of the blade trailing edge wake in the near wake. Phase-averaged and ensemble-averaged flow fields are analyzed to explain the flow physics. This work is supported by ONR.

  3. A hybrid approach for damage detection of structures under operational conditions

    Science.gov (United States)

    Fadel Miguel, Leandro Fleck; Holdorf Lopez, Rafael; Fadel Miguel, Letícia Fleck

    2013-09-01

    This paper presents a hybrid stochastic/deterministic optimisation algorithm to solve the target optimisation problem of vibration-based damage detection. The use of a numerical solution of the representation formula to locate the region of the global solution, i.e., to provide a starting point for the local optimiser, which is chosen to be the Nelder-Mead algorithm (NMA), is proposed. A series of numerical examples with different damage scenarios and noise levels was performed under impact and ambient vibrations. Thereafter, an experimental study of three cantilever beams with several different damage scenarios was conducted. To test the accuracy and efficiency of the optimisation algorithm, its results were compared to previous procedures available in the literature, which employed different solutions such as the genetic algorithm (GA), the harmony search algorithm (HS) and the particle swarm optimisation (PSO) algorithm. The performance of the proposed optimisation scheme was more accurate and required a lower computational cost than the GA, HS and PSO algorithms, emphasising the capacity of the proposed methodology for its use in damage diagnosis and assessment. In addition, the methodology was able to handle incomplete measurements and truncated mode shapes, which is of paramount importance for dealing with operational conditions in long-term structural health monitoring (SHM) applications.

  4. Treatment of oily wastewater by ultrafiltration: The effect of different operating and solution conditions

    Energy Technology Data Exchange (ETDEWEB)

    Hesampour, M

    2009-07-01

    In many industries, such as petroleum production, and the petrochemical, metal, food and cosmetics industries, wastewaters containing an emulsion of oil in water are often produced. The emulsions consist of water (up to 90%), oils (mineral, animal, vegetable and synthetic), surfactants and other contaminates. In view of its toxic nature and its deleterious effects on the surrounding environment (soil, water) such wastewater needs to be treated before release into natural water ways. Membrane-based processes have successfully been applied in industrial applications and are considered as possible candidates for the treatment of oily wastewaters. Easy operation, lower cost, and in some cases, the ability to reduce contaminants below existing pollution limits are the main advantages of these systems. The main drawback of membranes is flux decline due to fouling and concentration polarisation. The complexity of oil-containing systems demands complementary studies on issues related to the mitigation of fouling and concentration polarisation in membranebased ultrafiltration. In this thesis the effect of different operating conditions (factors) on ultrafiltration of oily water is studied. Important factors are normally correlated and, therefore, their effect should be studied simultaneously. This work uses a novel approach to study different operating conditions, like pressure, flow velocity, and temperature, and solution properties, like oil concentration (cutting oil, diesel, kerosene), pH, and salt concentration (CaCl{sub 2} and NaCl)) in the ultrafiltration of oily water, simultaneously and in a systematic way using an experimental design approach. A hypothesis is developed to describe the interaction between the oil drops, salt and the membrane surface. The optimum conditions for ultrafiltration and the contribution of each factor in the ultrafiltration of oily water are evaluated. It is found that the effect on permeate flux of the various factors studied strongly

  5. Performance measurements of the effect of simulator training on novice operators in simulated ice conditions

    Energy Technology Data Exchange (ETDEWEB)

    Power MacDonald, Stephanie; MacKinnon, Scott N. [Memorial University, St John' s (Canada); Re, Antonio Simoes; Power, Jonathan [National Research Council, Institute for Ocean Technology, St John' s (Canada)

    2011-07-01

    Research in the marine field suggests that training be part of a holistic teaching method, including traditional and other emerging methods. Currently, training for totally enclosed motor propelled survival craft (TEMPSC) operators is provided in sheltered ports in relatively benign conditions. Also the training is very limited for ice-covered water. This paper investigated the effectiveness of simulator-based training on the competency of a novice coxswain to navigate through a simulated ice field. This research compared the performance of simulator training in comparison with traditional standard certification and watchkeeping (STCW) training for lifeboats in ice fields. Virtual marine technologies (VMT) developed the full mission S class simulator used for the training. The full-scale field trials were carried out using a TEMPSC IMO/SOLAS approved for 20 occupants. This research demonstrated through the results of the post testing questionnaire data that simulator training could provide an increased sense of confidence after training on the simulator, and lead to an increase of competency.

  6. Transient two-phase CFD simulation of overload operating conditions and load rejection in a prototype sized Francis turbine

    Science.gov (United States)

    Mössinger, Peter; Jung, Alexander

    2016-11-01

    An increasing shift in operating conditions of hydropower turbines towards peak load operations comes with the necessity for numerical methods to account for such operations. This requires modifications to state-of-the-art CFD simulations. In the first part of this paper a 1D hydroacoustic model to represent the pressure oscillations in the penstock was introduced and coupled with a commercial CFD solver. Based on previous studies, various changes in cavitation and turbulence modeling were done to influence the behavior of a cavitating vortex rope typically occurring at high load conditions of a Francis turbine. In the second part, mesh motion was added to this model to simulate a load rejection starting from full load conditions. It was shown that additional extensions to the 3D CFD model are compulsory to model specific operating conditions as well as transient operations. Thus, accordance with measurement data at overload operation was improved and only small deviations remained. For the load rejection the maximum overspeed was well captured and the comparison of guide vane torques with model test measurements showed a sufficient agreement. With the gained insights, occurring effects which influence the performance and the life-time can be detected and conclusions for the hydraulic design as well as the operating mode can be drawn. Upcoming studies will focus on evaluating the flow field in detail and on reducing the remaining deviations by further extending the mathematical model.

  7. Extraction of red cabbage anthocyanins: optimization of the operation conditions of the column process

    Directory of Open Access Journals (Sweden)

    Marcelo Fonseca Xavier

    2008-02-01

    Full Text Available The aim of this work was to extract anthocyanins from the red cabbage. Batch studies under several extraction conditions indicated that acetic acid in aqueous solution (10% V/V was the best solvent, used in the proportion of 0.25 g of red cabbage mL-1. At this condition, column assays were carried out to evaluate the influence of the ionic force, pH, solvent flow rate, recirculated volume of red cabbage juice and the mass of red cabbage. Results showed that the pH, recirculation and mass of red cabbage had statistically significant effects, where the optimum operation conditions found for the process were pH 2.3, recirculation volume of the solvent 0.83 L and mass of red cabbage 50 g.Desde os primórdios dos tempos as antocianinas são extraídas de vegetais, mas avanços que garantam um processo viável e rentável exigem conhecimento, quantificação e controle das condições de operação. Estudos em batelada sob várias condições de extração indicaram que ácido acético em solução aquosa (10% V/V foi o melhor solvente, quando usado na proporção de 0,25 g de repolho roxo mL-1. Nesta condição de operação foram feitos ensaios em coluna para avaliar a influência da força iônica, pH, taxa de escoamento do solvente, volume recirculado da solução de extração e massa de repolho roxo. Os resultados mostraram que o pH, recirculação e massa de repolho foram estatisticamente significativos, e as condições ótimas de operação encontradas para o processo foram pH 2,3, volume de solvente recirculado de 0,83 L e massa de repolho roxo igual a 50g.

  8. [Application of operant conditioning techniques to forensic toxicology: experimental studies on alcohol and abusable drugs].

    Science.gov (United States)

    Hishida, S

    1996-10-01

    This paper describes some experiments that apply the operant conditioning techniques to forensic toxicological research. These techniques may be useful in investigating the mechanisms of action, toxic symptoms, legal competence and drug metabolism associated with substance abuse such as abuse of alcohol, psychotropic drugs, narcotics, stimulants, and organic solvents. 1) Genetic research on alcohol preference in rats. We applied operant conditioning to investigate alcohol preference in rats and constructed an apparatus for the measurement of discriminated operate responses for water or alcohol reinforcement in rat. This apparatus is a modified Skinner box with a one-lever two-liquid system. Fixed ratio-10 (FR-10) schedules of reinforcement are used to increase the work of the rat before it obtains the reinforcement. The voluntary choice of water or 10% ethanol by the rat can be assessed quantitatively by measuring the lever-pushing responses. It is an extremely useful method for measuring the real alcohol preference of rats. A rat was kept in a Skinner box overnight. The numbers of responses and reinforcement for water and ethanol and the volumes of the two liquids consumed were recorded. The ratio of ethanol reinforcement was defined as the number of ethanol reinforcement to the total number of ethanol and water reinforcement. The ratio of ethanol intake was defined as the volume of ethanol consumed to the volume of water and ethanol consumed. Ethanol consumption per g body weight was calculated from the volume of ethanol consumed by the rat. We used this apparatus to investigate alcohol preference of more than 300 Wistar Albino Rats, and divided them into a high alcohol preference (HAP) group and a low alcohol preference (LAP) group. Inbreeding between littermates was conducted in each of the HAP and LAP groups. The liver tissue of each offspring was obtained and the cytosol fraction was collected and subjected to isoelectric focusing using polyacrylamide gel

  9. 76 FR 81360 - Special Conditions: Gulfstream Aerospace LP (GALP) Model G280 Airplane, Operation Without Normal...

    Science.gov (United States)

    2011-12-28

    ... G280 Airplane, Operation Without Normal Electrical Power AGENCY: Federal Aviation Administration (FAA... associated with operation without normal electrical power. The applicable airworthiness regulations do not... Model G280 will have a novel or unusual design feature associated with operation without...

  10. A thermal model for analysis of hermetic reciprocating compressors under the on-off cycling operating condition

    Science.gov (United States)

    Lohn, S. K.; Diniz, M. C.; Deschamps, C. J.

    2015-08-01

    The on-off cycling operating condition of compressors is very common in low capacity refrigeration systems, being characterized by alternate periods in which the compressor is either operating (on) or idle (off). Thermal interactions between the compressor components affect its performance during the operating period and establish the initial condition for the compressor start up from idle condition. This paper presents a numerical model to predict the temperature field of hermetic reciprocating compressors under on-off cycling conditions. The model adopts a lumped formulation for control volumes formed in the fluid solution domain and the finite volume method to solve heat conduction in the solid components. Some required heat transfer coefficients were experimentally adjusted. Predictions for temperature were compared to measurements and good agreement was observed, especially for the thermal transient during the period in which the compressor is off.

  11. Support of the landscape amenity function of agriculture and trade liberalisation

    Directory of Open Access Journals (Sweden)

    Simona Kubíčková

    2004-01-01

    Full Text Available Recent agricultural policy and trade discussions have given increasing attention to “multifunctionality”, the notion, that agriculture provides multiple outputs that include public goods (such as landscape amenities as well as privately traded commodities. A frequent point of contention is also whether payment for the provision of non-commodity outputs distorts trade by giving domestic farmers a competitive advantage over foreign competitors. The paper reviews some requirements for environmental policy design and the role of property rights for the justification of the development of compensation programs targeted to landscape protection. The second part of the paper illustrates the possibilities, how to use results of Contingent Valuation (CV study of landscape amenity benefits of agriculture to prove eligibility for agri-environmental payments in the case of the Protected Landscape Area White Carpathians (Bílé Karpaty. It is documented in the paper, that Contingent Valuation can provide useful information about genuine concern and overall efficiency of compensation programs as well as people’s views about alternative ethical ends, besides human well-being, that policy makers should take in consideration.

  12. Socioeconomic assessment guidance report: Determining the effects of amenity characteristics on business location decisions

    Energy Technology Data Exchange (ETDEWEB)

    Allison, T.

    1993-02-01

    Evaluating perception-based impacts of hazardous waste facilities has become an increasingly important part of socioeconomic impact assessments in recent years. One area of discussion has been the potential effect of risk perceptions on business location decision making. This report evaluates the importance of environmental amenities (broadly defined to include natural, cultural, and recreational features; environmental quality; and other indexes of quality of life) with respect to decisions on locating both manufacturing and business service activities. It discusses the major theoretical and empirical issues that arise in attempting to determine the effects of environmental amenities on the location choices for businesses and business activities. This discussion is followed by a survey of major findings from the academic literature and a review of research by the state of Nevada. A number of recommendations for further research are also provided to help the US Department of Energy`s Office of Civilian Radioactive Waste Management better understand the importance of perception-based impacts in business location decision making and estimate the scale of socioeconomic impacts that would result from siting a high-level waste repository in Nevada.

  13. Effect of operating conditions in soil aquifer treatment on the removals of pharmaceuticals and personal care products.

    Science.gov (United States)

    He, Kai; Echigo, Shinya; Itoh, Sadahiko

    2016-09-15

    Soil aquifer treatment (SAT) is an alternative advanced treatment for wastewater reclamation, and it has the potential to control micropollutants including pharmaceuticals and personal care products (PPCPs). However, the relationship of operating conditions in SAT and removals of micropollutants was not clear. In this study, the effects of operating conditions on the removals of PPCPs were evaluated by using lab-scale columns and plant pilot-scale reactors under different operating conditions. Firstly, weathered granite soil (WGS), standard sand (SAND) and Toyoura standard sand (TS) have different soil characteristics such as total organic carbon (TOC) and cation exchange capacity (CEC). In the columns with these packing materials, the removals of carboxylic analgesics and antilipidemics were effective regardless packing materials. The removals of antibiotics were more effective in WGS than in TS and SAND, indicating high TOC and CEC enhance the sorption in SAT. Secondly, with the extension of hydraulic retention time (HRT), the removals of sulfamethoxazole, acetaminophen, crotamiton, and antipyrine were improved in WGS columns, and adaptable biodegradation for moderately removable PPCPs was formed. Thirdly, the removal efficiencies of sulfamethoxazole and crotamiton were higher in the WGS column under vadose condition than in the WGS column under saturated condition, because of aerobic condition in WGS column under vadose condition. Though long HRT and vadose condition had positive influence on the removals of several PPCPs such as sulfamethoxazole, WGS column with an HRT of 7days under saturated condition removed most PPCPs. Copyright © 2016 Elsevier B.V. All rights reserved.

  14. Volitional enhancement of firing synchrony and oscillation by neuronal operant conditioning: interaction with neurorehabilitation and brain-machine interface

    Directory of Open Access Journals (Sweden)

    Yoshio eSakurai

    2014-02-01

    Full Text Available In this review, we focus on neuronal operant conditioning in which increments in neuronal activities are directly rewarded without behaviors. We discuss the potential of this approach to elucidate neuronal plasticity for enhancing specific brain functions and its interaction with the progress in neurorehabilitation and brain–machine interfaces. The key to-be-conditioned activities that this paper emphasizes are synchronous and oscillatory firings of multiple neurons that reflect activities of cell assemblies. First, we introduce certain well-known studies on neuronal operant conditioning in which conditioned enhancements of neuronal firing were reported in animals and humans. These studies demonstrated the feasibility of volitional control over neuronal activity. Second, we refer to the recent studies on operant conditioning of synchrony and oscillation of neuronal activities. In particular, we introduce a recent study showing volitional enhancement of oscillatory activity in monkey motor cortex and our study showing selective enhancement of firing synchrony of neighboring neurons in rat hippocampus. Third, we discuss the reasons for emphasizing firing synchrony and oscillation in neuronal operant conditioning, the main reason being that they reflect the activities of cell assemblies, which have been suggested to be basic neuronal codes representing information in the brain. Finally, we discuss the interaction of neuronal operant conditioning with neurorehabilitation and brain–machine interface (BMI. We argue that synchrony and oscillation of neuronal firing are the key activities required for developing both reliable neurorehabilitation and high-performance BMI. Further, we conclude that research of neuronal operant conditioning, neurorehabilitation, BMI, and system neuroscience will produce findings applicable to these interrelated fields, and neuronal synchrony and oscillation can be a common important bridge among all of them.

  15. Etude theorique et experimentale des evaporateurs de dioxyde de carbone operant dans des conditions de givrage

    Science.gov (United States)

    Bendaoud, Adlane Larbi

    Les evaporateurs de refrigeration sont surtout du type tube a ailettes, appeles serpentins, et fonctionnent dans l'une des conditions suivantes: seche, humide ou avec formation de givre. Il a ete demontre que la formation du givre sur la paroi exterieure de l'echangeur engendre une surconsommation energetique a cause des operations de degivrage puisque 15 a 20% seulement de la chaleur produite sert au degivrage tandis que le reste est dissipee dans l'environnement [1]. Avec l'avenement des nouveaux refrigerants, moins nocifs envers l'environnement, l'industrie du froid se trouve penalisee du fait que peu ou pas de composantes mecaniques (compresseur, pompe, echangeur...etc.) adaptees sont disponibles [3]. Il s'agit pour la communaute des frigoristes de combler ce retard technologique en redeveloppant ces composantes mecaniques afin qu'elles soient adaptees aux nouveaux refrigerants. Dans cette optique, et afin de mieux comprendre le comportement thermique des evaporateurs au CO2 fonctionnant dans des conditions seches, qu'un groupe de chercheurs du CanmetENERGIE avaient lance, en 2000, un programme de R & D. Dans le cadre de programme un outil de simulation des evaporateurs au CO2 a ete developpe et un banc d'essai contenant une boucle secondaire de refrigeration utilisant le CO2 comme refrigerant a ete construit. Comme continuite de ce travail de recherche, en 2006 ce meme groupe de recherche a lance un nouveau projet qui consiste a faire une etude theorique et experimentale des evaporateurs au CO2 operants dans des conditions de givrage. Et, c'est exactement dans le cadre de ce projet que se positionne ce travail de these. Ce travail de recherche a ete entrepris pour mieux comprendre le comportement thermique et hydrodynamique des serpentins fonctionnant dans des conditions de givrage, l'effet des circuits de refrigerant ainsi que celui des parametres geometriques et d'operation. Pour cela, un travail theorique supporte par une etude experimentale a ete effectue

  16. Operant conditioning and discrimination of alpha: some methodological limitations inherent in response-discrimination experiments.

    Science.gov (United States)

    Cott, A; Pavloski, R P; Black, A H

    1981-09-01

    Studies on the operant conditioning of central nervous system activity have produced results interpreted as demonstrating that responses, certain properties of responses, or response-produced stimuli can function as discriminative stimuli. It is assumed that the feedback stimulus in biofeedback makes the subject aware of the internal response and that by becoming aware of the response, the subject can acquire voluntary control over it. In this context, awareness is operationally defined as the ability to use the response as a discriminative stimulus. Since direct evidence for the assumed relationship between control and discrimination is lacking, an attempt was made to test the hypothesis that discrimination of a response automatically leads to control over that response. The discriminative stimuli were the presence and absence of occipital alpha electroencephalograph (EEG) activity. Data from two experiments are reported. The first study, employing naive subjects, was designed to answer the following questions: (a) Since pilot data indicated that subjects seemed to match their responses to the more probable type of trial, would increases in the probability of a correct response result when the probabilities of alpha and nonalpha trials were held near .50? (b) If correct responding does increase, would performance of these subjects in an alpha feedback task be enhanced relative to that of subjects not previously given discrimination training? and (c) If subjects could not learn the discrimination task, would feedback training enhance their performance in a subsequent discrimination task? Results from this study indicate that holding the probabilities of alpha and nonalpha discrimination trials near .50 results in an absence of learning curves, but leaves open the possibility that sophisticated subjects are capable of discriminating alpha and nonalpha activity. The second study deals with two questions: (a) Can sophisticated subjects learn to discriminate occipital

  17. Effects of organic phase, fermentation media, and operating conditions on lactic Acid extraction.

    Science.gov (United States)

    Hossain, Md Monwar; Maisuria, J L

    2008-01-01

    Lactic acid has extensive uses in the food, pharmaceutical, cosmetic and chemical industry. Lately, its use in producing biodegradable polymeric materials (polylactate) makes the production of lactic acid from fermentation broths very important. The major part of the production cost accounts for the cost of separation from very dilute reaction media where productivity is low as a result of the inhibitory nature of lactic acid. The current method of extraction/separation is both expensive and unsustainable. Therefore, there is great scope for development of alternative technology that will offer efficiency, economic, and environmental benefits. One of the promising technologies for recovery of lactic acid from fermentation broth is reactive liquid-liquid extraction. In this paper the extraction and recovery of lactic acid based on reactive processes is examined and the performance of a hydrophobic microporous hollow-fiber membrane module (HFMM) is evaluated. First, equilibrium experiments were conducted using organic solutions consisting of Aliquat 336/trioctylamine (as a carrier) and tri-butyl phosphate (TBP)/sunflower oil (as a solvent) The values of the distribution coefficient were obtained as a function of feed pH, composition of the organic phase (ratio of carrier to solvent), and temperature (range 8-40 degrees C). The optimum extraction was obtained with the organic phase consisting of a mixture of 15 wt % tri-octylamine (TOA) and 15% Aliquat 336 and 70% solvent. The organic phase with TBP performed best but is less suitable because of its damaging properties (toxicity and environmental impact) and cost. Sunflower oil, which performed moderately, can be regarded as a better option as it has many desirable characteristics (nontoxic, environment- and operator-friendly) and it costs much less. The percentage extraction was approximately 33% at pH 6 and at room temperature (can be enhanced by operating at higher temperatures) at a feed flow rate of 15-20 L

  18. The effects of operator position, pallet orientation, and palletizing condition on low back loads in manual bag palletizing operations.

    Science.gov (United States)

    Gallagher, Sean; Heberger, John R

    2015-05-01

    Many mining commodities are packaged and shipped using bags. Small bags are typically loaded onto pallets for transport and require a significant amount of manual handling by workers. This specific task of manual bag handling has been associated with the development of musculoskeletal disorders (MSDs), especially low back disorders. This study evaluates the biomechanical demands of different work layouts when performing manual palletizing of small bags, and evaluates the biomechanical stresses associated with different stacking techniques. Results indicate that peak forward bending moments as well as spinal compression and shear forces are higher when the pallet is situated at the side of the conveyor as opposed to the end of the conveyor. At low levels of the pallet, controlled bag placement results in higher peak forward bending moments than stacking at higher levels and when dropping the bag to lower levels. The results of this study will be used to inform the development of an audit tool for bagging operations in the mining industry.

  19. Influence of different operating conditions on irrigation uniformity with microperforated tapes

    Science.gov (United States)

    Moreno Pizani, María Alejandra; Jesús Farías Ramírez, Asdrúbal

    2013-04-01

    Irrigated agriculture is a safe alternative to meet the growing demand for food. Numerous studies show that proper management of localized irrigation can increase crop yields and reduce soil salinization. Therefore, periodic field systems irrigation assessments are needed in order to optimize the use efficiency of irrigation water, as well as, to increase the agricultural area covered by the same amount of water and to reduce the environmental impact. It was assessed the behavior of micro perforated tapes under different operating conditions, crops and regions of Venezuela. Evaluations were made on irrigated areas using Santeno ® Type I tape with the following crops: Banana (Musa sp), lettuce (Lactuca sativa L.), carrot (Daucus carota L) and forage sugar cane (Saccharum officinarum). In the other hand, Santeno ® Type II tape was used with papaya (Carica papaya L.) and melon (Cucumis melo L.) crops (the last crop using inverted irrigation tape). The procedures used for sampling and determining the uniformity indices of the system were performed using a series of adjustments to the methodology proposed by Keller and Karmeli (1975), Deniculi (1980) and De Santa and De Juan (1993), in order to increase the number of observations as a function of irrigation time. The calculated irrigation uniformity indices were as follow: Distribution Coefficient (UD), Uniformity Coefficient (CUC), Coefficient of Variation of Flows (CV) and Statistical Uniformity Coefficient (Us). The indices characterization was made according to Merrian and Keller (1978); Bralts (1986); Pizarro (1990) y ASAE (1996), respectively. The results showed that the irrigation uniformity for the evaluated systems varied from excellent to unacceptable, mainly due to the lack of maintenance and the absent of manometric connectors. Among the findings, it is possible to highlight the need for technical support to farmers, both in the installation, management and maintenance of irrigation systems. In this sense

  20. Performance of a vertical subsurface flow constructed wetland under different operational conditions

    Directory of Open Access Journals (Sweden)

    Sara G. Abdelhakeem

    2016-09-01

    Full Text Available The performance of a vertical subsurface flow constructed wetland (VSSFCW for sewage effluent treatment was studied in an eight month experiment under different operational conditions including: vegetation (the presence or absence of common reeds “Phragmites australis”, media type (gravel or vermiculite, and mode of sewage feeding (continuous or batch. Plants had a significant effect (P < 0.05 on the removal efficiency and mass removal rate of all pollutants, except phosphorous. The average removal efficiencies of chemical oxygen demand (COD, biological oxygen demand (BOD, total suspended solids (TSS, ammonium (NH4 and total-P (TP were 75%, 84%, 75%, 32% and 22% for the planted beds compared to 29%, 37%, 42%, 26% and 17%, respectively, for the unplanted beds. The VSSFCW was ineffective in removing nitrate (NO3. The effect of either media type or feeding mode system on the removal efficiency of COD and BOD was insignificant. Vermiculite media significantly (P < 0.05 increased the efficiency of the wetland in removing NH4, TP and dissolved phosphorous (DP when compared with gravel particularly in the planted beds. The batch mode was more effective in removing TSS and NH4 compared to the continuous mode. Volumetric rate constant (kV was different for various pollutants and significantly increased due to the presence of plants. Media type had no significant effect on the values of kV for COD, BOD and TSS, while kV for NH4 and TP under vermiculite in the planted beds and kV for P in the unplanted beds were significantly higher than those under gravel.

  1. Extracellular polymeric substances (EPS) in upflow anaerobic sludge blanket (UASB) reactors operated under high salinity conditions.

    Science.gov (United States)

    Ismail, S B; de La Parra, C J; Temmink, H; van Lier, J B

    2010-03-01

    Considering the importance of stable and well-functioning granular sludge in anaerobic high-rate reactors, a series of experiments were conducted to determine the production and composition of EPS in high sodium concentration wastewaters pertaining to anaerobic granule properties. The UASB reactors were fed with either fully acidified substrate (FAS) consisting of an acetate medium (reactor R1) or partly acidified substrate (PAS) consisting of acetate, gelatine and starch medium (reactors R2, R3, and R4). For EPS extraction, the cation exchange resin (CER) method was used. Strength and particle size distribution were determined by assessing the formation of fines sludge under conditions of high shear rate and by laser diffraction, respectively. Batch tests were performed in 0.25L bottles to study Ca(2+) leaching from anaerobic granular sludge when incubated in 20g Na(+)/L in the absence of feeding for 30 days. Results show a steady increase in the bulk liquid Ca(2+) concentration during the incubation period. UASB reactor results show that the amounts of extracted proteins were higher from reactors R2 and R3, fed with PAS compared to the sludge samples from reactor R1, fed with FAS. Strikingly, the amount of extracted proteins also increased for all reactor sludges, irrespective of the Na(+) concentration applied in the feed, i.e. 10 or 20gNa(+)/L. PAS grown granular sludges showed an important increase in particle size during the operation of the UASB reactors. Results also show that, addition of 1gCa(2+)/L to the high salinity wastewater increases the granules' strength. Copyright 2009 Elsevier Ltd. All rights reserved.

  2. Optimum Operating Conditions for Epoxidation Reaction of Jojoba and Castor Oils

    Directory of Open Access Journals (Sweden)

    El-Adly R. A

    2014-03-01

    Full Text Available The goal of this paper is to determine the best set of parameters such as, glacial acetic acid to ethylenic unsaturation mole ratio (acid/ethylene, hydrogen peroxide to ethylenic unsaturation mole ratio (H2O2/ethylene and temperature on epoxidation conversion based on experimental results, with respect to time. The effect of these parameters has been studied in a separate set of experiments. Their ranges were as follows: 0.2-0.8Wt%, 0.75-3Wt%, and 40oC-80oC respectively. Six models have been introduced to indicate the effect of these three variables on conversion for both jojoba and castor oil, and the prediction abilities of the resultant models were tested. Regression analysis is used to extract the introduced non linear models. In addition, two new correlations have been introduced to incorporate all the studied variables and their effect on conversion simultaneously for both jojoba and castor oil. An optimization program has been introduced to determine the optimum operating conditions for maximum conversion for both jojoba and castor oil. The study shows that, the maximum conversion for epoxidized jojoba oil (66% could be achieved at acid/ethylene ratio: 0.4, H2O2/ethylene ratio: 1.44; temp: 66.5 and time is 8hr. While the maximum conversion for epoxidized castor oil (53.24% could be achieved at acid/ethylene ratio: 0.37; H2O2/ethylenes ratio: 1.32; temp: 61 and time is 8hr. the model results are strongly agreed with the experimental results.

  3. Modeling of a Cogeneration System with a Micro Gas Turbine Operating at Partial Load Conditions

    Directory of Open Access Journals (Sweden)

    José Carlos Dutra

    2017-06-01

    Full Text Available The integration of absorption chillers in micro-cogeneration systems based on micro-gas turbines can be useful as an appropriate strategy to increase the total system energy efficiency. Since it is an area intensive in technology, it is necessary to develop and use models of simulation, which can predict the behavior of the whole system and of each component individually, at different operating conditions. This work is part of a research project in high efficiency cogeneration systems, whose purpose at this stage is to model a micro-cogeneration system, which is composed of a micro gas turbine, Capstone C30, a compact cross flow finned tube heat exchanger and an absorption chiller. The entire model is composed of specifically interconnected models, developed and validated for each component. The simulation of the microturbine used a thermodynamic analytic model, which contains a procedure used to obtain the micro turbine characteristic performance curves, which is closed with the thermodynamic Brayton cycle model. In the cogeneration system discussed in this paper, the compact heat exchanger was used to heat thermal oil, which drives an absorption chiller. It was designed, characterized and installed in a cogeneration system installed at the Centre d'Innovació Tecnològica en Revalorització Energètica i Refrigeració, Universtat Rovira i Virgili. Its design led to the heat exchanger model, which was coupled with the micro turbine model. Presented in this work is a comparison between the data from the model and the experiments, demonstrating good agreement between both results.

  4. Optimum thermal sizing and operating conditions for once through steam generator

    Energy Technology Data Exchange (ETDEWEB)

    Yi, Kunwoo; Ju, Kyongin; Im, Inyoung; Kim, Eunkee [KEPCO Engineering and Construction Company., Inc., Daejeon (Korea, Republic of)

    2014-10-15

    The steam generator is designed to be optimized so as to remove heat and to produce steam vapor. Because of its importance, theoretical and experimental researches have been performed on forced convection boiling heat transfer. The purpose of this study is to predict the thermal behavior and to perform optimum thermal sizing of once through steam generator. To estimate the tube thermal sizing and operating conditions of the steam generator, the analytical modeling is employed on the basis of the empirical correlation equations and theory. The optimized algorithm model, Non-dominated Sorting Genetic Algorithm (NSGA)-II, uses for this analysis. This research is focused on the design of in-vessel steam generator. An one dimensional analysis code is developed to evaluate previous researches and to optimize steam generator design parameters. The results of one-dimensional analysis need to be verified with experimental data. Goals of multi-objective optimization are to minimize tube length, pressure drop and tube number. Feedwater flow rate up to 115.425kg/s is selected so as to have margin of feedwater temperature 20 ..deg. C. For the design of 200MWth once through steam generator, it is evaluated that the tube length shall be over 12.0m for the number of tubes, 2500ea, and the length of the tube shall be over 8.0m for the number of tubes, 4500ea. The parallel coordinates chart can be provided to determine the optimal combination of number of tube, pressure drop, tube diameter and length.

  5. Complex matrix multiplication operations with data pre-conditioning in a high performance computing architecture

    Science.gov (United States)

    Eichenberger, Alexandre E; Gschwind, Michael K; Gunnels, John A

    2014-02-11

    Mechanisms for performing a complex matrix multiplication operation are provided. A vector load operation is performed to load a first vector operand of the complex matrix multiplication operation to a first target vector register. The first vector operand comprises a real and imaginary part of a first complex vector value. A complex load and splat operation is performed to load a second complex vector value of a second vector operand and replicate the second complex vector value within a second target vector register. The second complex vector value has a real and imaginary part. A cross multiply add operation is performed on elements of the first target vector register and elements of the second target vector register to generate a partial product of the complex matrix multiplication operation. The partial product is accumulated with other partial products and a resulting accumulated partial product is stored in a result vector register.

  6. The Attempt To Assess The Technical Condition Of A Gas Turbine Blade When Information On Its Operating Condition Is Limited

    Directory of Open Access Journals (Sweden)

    Błachnio Józef

    2014-12-01

    Full Text Available The paper discloses a non-invasive method of visual inspection based on processing of images taken for blade surfaces in the spectrum of visible light and then analyzed with the use of a computer-aided technology. The method of computer-aided analysis of images for blade surfaces is presented in details along with the obtained outcome, whilst the results from metallographic investigation of the blade superalloy are disclosed as well. The comparison is made between the results obtained from the analysis of images for blade surface and the results from the metallographic investigation of their structures. Finally, the relationship is established between parameters of digital images taken for surfaces of gas turbine blades in the visible spectrum of electromagnetic waves and microstructural parameters of the turbine blade metal. The completed investigations and analyses reveal that troubleshooting of gas turbine blades, which employs digital processing of images taken for its surface, offers new opportunities to determine the condition of blades after a long-term impact of a working agent at high temperature.

  7. Effects of peroxidized corn oil on performance, AMEn, and abdominal fat pad weight in broiler chicks.

    Science.gov (United States)

    Ehr, I J; Kerr, B J; Persia, M E

    2015-07-01

    There is a trend to use more alternative lipids in poultry diets, either through animal-vegetable blends, distillers corn oil, or yellow grease. This has resulted in the use of lipids in poultry diets with a higher concentration of unsaturated fatty acids, which have a greater potential for peroxidation. The objective of this experiment was to determine the effects of peroxidized corn oil on broiler performance, dietary AMEn, and abdominal fat pad weight. The same refined corn oil sample was divided into 3 subsamples, 2 of which were exposed to different peroxidative processes. The 3 diets contained the unperoxidized corn oil (UO), a slowly peroxidized corn oil (SO; heated for 72 h at 95°C with compressed air flow rate of 12 L/min), or a rapidly peroxidized corn oil (RO; heated for 12 h at 185°C with compressed air flow rate of 12 L/min). Diets were fed from 0 to 14 d of age with each lipid fed at a 5% inclusion rate, continuing on from 15 to 27 d of age with each lipid fed at a 10% inclusion rate. There were 6 Ross 708 broiler chicks per cage with 10 replicates for each of the 3 dietary treatments. Abdominal fat pad and excreta collection was performed on d 27. Body weight gain, feed intake and feed efficiency were measured for the 0 to 14 and 0 to 27 d periods. The increased level of peroxidation reduced AMEn in broiler diets (UO = 3,490 kcal/kg; SO = 3,402 kcal/kg; RO = 3,344 kcal/kg on an as-is basis; SEM = 12.9, P ≤ 0.01). No significant treatment differences were observed among oil supplemented birds for BW gain, feed intake, feed efficiency, or abdominal fat pad weight. In conclusion, corn oil peroxidation status resulted in a decrease in dietary AMEn, but had minimal effects on broiler performance or fat pad weights.

  8. Semi-Group Theory for the Stokes Operator with Navier-Type Boundary Conditions on L p -Spaces

    Science.gov (United States)

    Al Baba, Hind; Amrouche, Chérif; Escobedo, Miguel

    2017-02-01

    In this article we consider the Stokes problem with Navier-type boundary conditions on a domain {Ω}, not necessarily simply connected. Since, under these conditions, the Stokes problem has a non trivial kernel, we also study the solutions lying in the orthogonal of that kernel. We prove the analyticity of several semigroups generated by the Stokes operator considered in different functional spaces. We obtain strong, weak and very weak solutions for the time dependent Stokes problem with the Navier-type boundary condition under different hypotheses on the initial data u 0 and external force f. Then, we study the fractional and pure imaginary powers of several operators related with our Stokes operators. Using the fractional powers, we prove maximal regularity results for the homogeneous Stokes problem. On the other hand, using the boundedness of the pure imaginary powers, we deduce maximal {Lp-Lq} regularity for the inhomogeneous Stokes problem.

  9. 76 FR 8314 - Special Conditions: Gulfstream Model GVI Airplane; Operation Without Normal Electric Power

    Science.gov (United States)

    2011-02-14

    ..., 2006. The Gulfstream Model GVI airplane will be an all-new, two- engine jet transport airplane with an... traditional designs, the GVI must be designed for operation with the normal sources of engine and auxiliary...; Operation Without Normal Electric Power AGENCY: Federal Aviation Administration (FAA), DOT. ACTION:...

  10. The effect of stressed economic conditions on operational risk loss distributions

    Directory of Open Access Journals (Sweden)

    Ja'nel Esterhuysen

    2010-12-01

    Full Text Available The depth and duration of the credit crisis has highlighted a number of problems in modern finance. Banks have been accused of excessive risk taking, rating agencies of severe conflicts of interest, central banks of neglecting the inflation of asset price bubbles and national supervisors of lax regulatory controls. Credit and market losses have been considerable. Operational losses have also surged as surviving corporates merge or acquire less fortunate ones without the requisite controls. Furthermore, as more jobs get made redundant it is believed that people are getting forced to play their hand to get involved in internal fraud as their sources of income has dried up drastically and stealing from the institution seems to be their last resort.. The main objective of this paper is to establish if there has been a changed in the nature of operational risk with regards to the number of operational losses as well as their impact pre and during the crisis. The way in which operational losses have been affected will be presented and a comparison will be made between operational loss characteristics pre and during the crisis. Some of the main findings of this paper were that operational losses shown little change in frequency, but shown a significant increase in severity, meaning that their financial impact has been more severe during the crisis.  Therefore it is quite safe to say that the financial crisis most defiantly had an impact on operational risk as the impact of operational losses became much more severe

  11. Monitoring Attention During Operant Conditioning in Six and Seven Month Old Infants.

    Science.gov (United States)

    Strain, Barbara; Vietze, Peter M.

    The purpose of the present study was to investigate more directly the effects of content and repetition of contingent visual feedback on a discrete operant pulling response and accompanying visual attention in 24 six- to seven-month old infants. Simultaneous recording was made of infant operant behavior and visual attention. Results indicated…

  12. Determining the microwave coupling and operational efficiencies of a microwave plasma assisted chemical vapor deposition reactor under high pressure diamond synthesis operating conditions.

    Science.gov (United States)

    Nad, Shreya; Gu, Yajun; Asmussen, Jes

    2015-07-01

    The microwave coupling efficiency of the 2.45 GHz, microwave plasma assisted diamond synthesis process is investigated by experimentally measuring the performance of a specific single mode excited, internally tuned microwave plasma reactor. Plasma reactor coupling efficiencies (η) > 90% are achieved over the entire 100-260 Torr pressure range and 1.5-2.4 kW input power diamond synthesis regime. When operating at a specific experimental operating condition, small additional internal tuning adjustments can be made to achieve η > 98%. When the plasma reactor has low empty cavity losses, i.e., the empty cavity quality factor is >1500, then overall microwave discharge coupling efficiencies (η(coup)) of >94% can be achieved. A large, safe, and efficient experimental operating regime is identified. Both substrate hot spots and the formation of microwave plasmoids are eliminated when operating within this regime. This investigation suggests that both the reactor design and the reactor process operation must be considered when attempting to lower diamond synthesis electrical energy costs while still enabling a very versatile and flexible operation performance.

  13. Effects of temperature conditions in a gas collector on operation of primary and secondary gas coolers

    Energy Technology Data Exchange (ETDEWEB)

    Chuishchev, V.M.; Selivanova, Z.G.; Vasyuta, V.I.

    1988-04-01

    Discusses composition of coal gas leaving coke ovens and temperature effects on its composition in a gas collector and cooling systems. Effects of coal gas temperature ranging from 78 to 90 C on operation of cooling systems are analyzed: cooling intensity, naphthalene buildup, etc. Analyses show that coal gas temperature fluctuations from 80 to 90 C do not influence gas collector operation, whereas operation of primary gas coolers is influenced by gas collector operation. When coal gas temperature is reduced from 88 to 80 C intensity of coal tar accumulation increases 2 times and that of naphthalene increases 5 to 6 times. Temperature of coal gas leaving the primary coolers ranges from 35 to 40 C. Types of primary coal gas coolers, their operation and performance are comparatively evaluated. Effects of gas cooler design on efficiency of coal tar separation from coal gas are discussed. 5 refs.

  14. Effect of operating conditions in soil aquifer treatment on the removals of pharmaceuticals and personal care products

    Energy Technology Data Exchange (ETDEWEB)

    He, Kai, E-mail: hekai@urban.env.kyoto-u.ac.jp; Echigo, Shinya; Itoh, Sadahiko

    2016-09-15

    Soil aquifer treatment (SAT) is an alternative advanced treatment for wastewater reclamation, and it has the potential to control micropollutants including pharmaceuticals and personal care products (PPCPs). However, the relationship of operating conditions in SAT and removals of micropollutants was not clear. In this study, the effects of operating conditions on the removals of PPCPs were evaluated by using lab-scale columns and plant pilot-scale reactors under different operating conditions. Firstly, weathered granite soil (WGS), standard sand (SAND) and Toyoura standard sand (TS) have different soil characteristics such as total organic carbon (TOC) and cation exchange capacity (CEC). In the columns with these packing materials, the removals of carboxylic analgesics and antilipidemics were effective regardless packing materials. The removals of antibiotics were more effective in WGS than in TS and SAND, indicating high TOC and CEC enhance the sorption in SAT. Secondly, with the extension of hydraulic retention time (HRT), the removals of sulfamethoxazole, acetaminophen, crotamiton, and antipyrine were improved in WGS columns, and adaptable biodegradation for moderately removable PPCPs was formed. Thirdly, the removal efficiencies of sulfamethoxazole and crotamiton were higher in the WGS column under vadose condition than in the WGS column under saturated condition, because of aerobic condition in WGS column under vadose condition. Though long HRT and vadose condition had positive influence on the removals of several PPCPs such as sulfamethoxazole, WGS column with an HRT of 7 days under saturated condition removed most PPCPs. - Highlights: • Soil organic matter and cation exchange capacity enhanced the removals of antibiotics in SAT. • A hydraulic retention time (HRT) of 7 days was sufficient for the removals of most PPCPs. • The removals of most selected PPCPs were similar under vadose and saturated conditions. • Vadose condition contributed to the

  15. Operative temperature and thermal sensation assessments in non-air-conditioned multi-storey hostels in Malaysia

    Energy Technology Data Exchange (ETDEWEB)

    Dahlan, N.D. [Department of Architecture, Faculty of Design and Architecture, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Jones, P.J.; Alexander, D.K. [Welsh School of Architecture, Cardiff University, Bute Building, King Edward VII Avenue, CF10 3NB (United Kingdom)

    2011-02-15

    This study assessed the influences of operative temperature on occupants' perceptions of indoor thermal condition in three non-air-conditioned multi-storey hostels in Klang Valley, Malaysia. The thermal conditions of 24 measured rooms were recorded with and without an operating ceiling fan from May until July 2007. Measurements were made simultaneously at three different floor levels, namely, at the first, fifth and top floor of each of the case study hostels. A questionnaire survey was completed by 298 female student occupants of the same case study hostels. The results suggested that even though a significance above p < 0.01 was recorded between the operative temperatures with and without fan operation, the temperature difference remained small, i.e., from 0.5 K to 1 K. The findings of the questionnaire survey showed that the occupants perceived the thermal conditions in rooms that were shaded with a projected balcony (shading ratio of 0.9), a long roof overhang (shading ratio of 1.6) and an operable window-to-wall ratio of 0.3 to be thermally comfortable. (author)

  16. Preliminary assessment of accident-tolerant fuels on LWR performance during normal operation and under DB and BDB accident conditions

    Science.gov (United States)

    Ott, L. J.; Robb, K. R.; Wang, D.

    2014-05-01

    Following the severe accidents at the Japanese Fukushima Daiichi Nuclear Power Station in 2011, the US Department of Energy initiated research and development on the enhancement of the accident tolerance of light water reactors by the development of fuels/cladding that, in comparison with the standard UO2/Zircaloy (Zr) system, can tolerate loss of active cooling in the core for a considerably longer time period while maintaining or improving the fuel performance during normal operations. Analyses are presented that illustrate the impact of these new candidate fuel/cladding materials on the fuel performance at normal operating conditions and on the reactor system under DB and BDB accident conditions.

  17. Nitrogen application in amenity-types of Lolium perenne L. grown for seed production

    DEFF Research Database (Denmark)

    Deleuran, Lise Christina; Boelt, Birte

    1998-01-01

    Three amenity-type perennial ryegrass (Lolium perenne) cultivars Elka, Taya and Pippin were undersown in 1991-93 in spring barley at Roskilde and Rnhave, Denmark, and given 0, 30 or 60 kg N ha-1 in autumn combined with 70, 100 or 130 kg N ha-1 in spring. Seed yield did not differ among cultivars...... content varied considerably among years but not cultivars. Correlation analysis of N content, yield components and seed yield revealed that autumn N application resulted in an increasing N content in shoots, fertile tiller number and seed weight. However, these two components were negatively correlated......, and total seed yield was therefore not affected. The one exception was in 1991 when at one location dry matter production in autumn was low, and autumn N application resulted in increased N content, fertile tiller number and seed yield...

  18. Nancy Berthier (dir., Le cinéma d´Alejandro Amenábar

    Directory of Open Access Journals (Sweden)

    Ana Recalde Delgado

    2010-01-01

    Full Text Available Cet ouvrage, auquel participent Jean-Paul Aubert, Elisa Costa, Françoise Heitz, Aurélie Ledoux, Jacques Terrasa et Pascale Thibaudeau, est coordonné par Nancy Berthier (Université Paris-Est, chercheuse passionnée du cinéma espagnol, qui a publié notamment Le franquisme et son image (1998, De la guerre à l´écran. ¡Ay Carmela! De Carlos Saura (1999 ou Le cinéma de Bigas Luna (2000. Le réalisateur qui fait l’objet de ce travail est le Chileno-Espagnol Alejandro Amenábar, jeune auteur de quat...

  19. The Effects on the Operating Condition of a Passenger Ship Retro-fitted with a Composite Superstructure

    DEFF Research Database (Denmark)

    Karatzas, Vasileios; Hjørnet, N. K.; Kristensen, Hans Otto Holmegaard

    2016-01-01

    the stability of the ship. In this work, the superstructure of a RoPax ferry has been redesigned using composite materials emphasizing the effects on the ship from an operational per-spective. The weight reduction has been calculated for a real-istic average operating condition quantifying the effects......As sustainability and climate change have come on the politi-cal agenda, the shipping industry will have to be operating energy efficient ships. An appealing step to achieve this goal is by designing superstructures made out of Fiber Reinforced Plastics (FRP) aiming at the reduction of the ship...

  20. Fuel rod behavior under normal operating conditions in Super Fast Reactor with high power density

    Energy Technology Data Exchange (ETDEWEB)

    Ju, Haitao, E-mail: haitaoju@gmail.com [Science and Technology on Reactor System Design Technology Laboratory, Chengdu, Sichuan 610041 (China); Ishiwatari, Yuki [Department of Nuclear Engineering and Management, The University of Tokyo, Hongo, Bunkyo, Tokyo 113-8656 (Japan); Oka, Yoshiaki [Joint Department of Nuclear Energy, Waseda University, Totsukamachi, Shinjuku, Tokyo 169-8050 (Japan)

    2015-08-15

    Highlights: • The improved core of Super Fast Reactor with high power density is analyzed. • We analyzed four types of the limiting fuel rods. • The influence of Pu enrichment and compressive stress to yield strength ratio are analyzed. • The improved fuel rod design of the new core is suggested. - Abstract: A Super Fast Reactor is a pressure-vessel type, fast spectrum SuperCritical Water Reactor (SCWR) which is presently researched in a Japanese project. A preliminary core has an average power density of 158.8 W/cc. However one of the most important advantages of the Super Fast Reactor is the higher power density compared to the thermal spectrum SCWR, which reduces the capital cost. After the sensitivity analyses on the fuel rod configurations, the fuel assembly configurations and the core configurations, an improved core with an average power density of 294.8 W/cc is designed by 3-D neutronic/thermal-hydraulic coupled calculations. In order to ensure the fuel rod integrity of new core design with high power density, the fuel rod behaviors under normal operating condition are analyzed using fuel performance code FEMAXI-6. The power histories of each fuel rod are taken from the neutronics calculation results in the core design. The cladding surface temperature histories are generated from the thermal-hydraulic calculation results in the core design. Four types of the limiting fuel rods, individually with the Maximum Cladding Surface Temperature (MCST), Maximum Power Peak (MPP), Maximum Discharge Burnup (MDB) and Different Coolant Flow Pattern (DCFP), are chosen to cover all the fuel rods in the core. The available design range of the fuel rod design parameters, such as initial gas plenum pressure, gas plenum position, gas plenum length, grain size and gap size, are found out in order to satisfy the following design criteria: (1) Maximum fuel centerline temperature should be less than 1900 °C. (2) Maximum cladding stress in circumferential direction should

  1. Gunite and Associated Tanks Waste Conditioning System: Description and Operational Summary

    Energy Technology Data Exchange (ETDEWEB)

    Emison, JA

    2002-03-14

    The purpose of this report is to describe and document the function, operational performance, problems encountered, lessons-learned, and overall assessment of the performance of the waste conditioning system (WCS) in the Gunite{trademark} and Associated Tanks (GAAT) remediation project at the Oak Ridge National Laboratory (ORNL). The GAAT are located in the main plant area of ORNL in the North and South Tank Farms. These tanks were constructed in 1943 as part of the Manhattan Project during World War II. Each tank in the South Tank Farm (STF) has a 50-ft inside diameter and a capacity of {approx}170,000 gal. Each Gunite tank in the North Tank Farm (NTF) has a 25-ft inside diameter with a capacity of {approx}44,000 gal. The GAAT were designed to receive radioactive and chemical wastes from ORNL processes. The tanks were constructed of Gunite, which is created by pneumatically spraying concrete over a wire mesh. Following construction, the site was backfilled so the domes of the tanks were covered with {approx}6 ft of earth. The STF tanks (W-5, -6, -7, -8, -9, and -10) are set in a 2 x 3 array with an east-west axis. The two GAAT in the NTF are on the north side of Central Avenue, and the STF is across the street. One additional Gunite tank, TH-4, is located {approx}300 ft east of the STF. TH-4 is a smaller, 20-ft inside diameter tank with a capacity of {approx}14,000 gal. Approximately 90% of the sludge inventory was removed from the STF tanks during a sluicing campaign in 1982-84 (Autry et al., 1990). Over 95% of the residual from the original sluicing was removed during the GAAT Remediation Project of 1997-2000. The NTF and STF tanks, as well as tank TH-4 were remediated under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) with regulatory oversight by the U.S. Environmental Protection Agency (EPA) and the Tennessee Department of Environment and Conservation (TDEC).

  2. Fatigue crack growth characteristics of nitrogen-alloyed type 347 stainless under operating conditions of a pressurized water reactor

    Energy Technology Data Exchange (ETDEWEB)

    Min, Ki Deuk; Hong, Seok Min; Kim, Dae Whan; Lee, Bong Sang [Korea Atomic Energy Research Institute, Nuclear Materials Safety Research Division, Daejeon (Korea, Republic of); Kim, Seon Jin [Hanyang University, Division of materials science and engineering, Seoul (Korea, Republic of)

    2017-06-15

    The fatigue crack growth behavior of Type 347 (S347) and Type 347N (S347N) stainless steel was evaluated under the operating conditions of a pressurized water reactor (PWR). These two materials showed different fatigue crack growth rates (FCGRs) according to the changes in dissolved oxygen content and frequency. Under the simulated PWR conditions for normal operation, the FCGR of S347N was lower than that of S347 and insensitive to the changes in PWR water conditions. The higher yield strength and better corrosion resistance of the nitrogen-alloyed Type 347 stainless steel might be a main cause of slower FCGR and more stable properties against changes in environmental conditions.

  3. Numerical Modeling of MILD Combustion at High Pressure to Predict the Optimal Operating Conditions

    KAUST Repository

    Vanteru, Mahendra Reddy

    2017-02-01

    This Chapter presents numerical simulation on MILD combustion operating at high pressure. Influence of preheat and dilution of oxidizer and operating pressure on stabilization of MILD combustion are presented. Three different preheat temperatures (1100, 1300 and 1500 K) and three different dilution levels (3, 6 and 9% O2) are simulated over an operating pressure variation from 1 atm to 16 atm. A classical jet in hot coflow burner is considered for this study. Total of 45 cases are simulated and analyzed. Essential characteristics of MILD combustion, i.e., maximum temperature $$ (T_{max} ) $$, temperature rise $$ (\\\\Delta T) $$ and temperature distributions, are analyzed. The distribution of emissions OH and CO are also studied and presented. Well-stabilized MILD combustion is observed for all cases except for two cases with high preheated (1500 K). Peak temperature is observed to decrease with increasing operating pressure for a given level of preheat and dilution. OH mass faction is reduced with increasing pressure. The CO emissions show little sensitivity to operating pressure. However, CO mass fraction is slightly higher at 1 atm operating pressure as compared to 4 to 16 atm. Since the residence time of reactants increases as the operating pressure increases, well-stabilized MILD combustion is observed for all highly diluted and low temperature preheat cases (3% O2 and 1100 K).

  4. Analysis of Actual Operating Conditions of an Off-grid Solid Oxide Fuel Cell

    Energy Technology Data Exchange (ETDEWEB)

    Dennis Witmer; Thomas Johnson; Jack Schmid

    2008-12-31

    Fuel cells have been proposed as ideal replacements for other technologies in remote locations such as Rural Alaska. A number of suppliers have developed systems that might be applicable in these locations, but there are several requirements that must be met before they can be deployed: they must be able to operate on portable fuels, and be able to operate with little operator assistance for long periods of time. This project was intended to demonstrate the operation of a 5 kW fuel cell on propane at a remote site (defined as one without access to grid power, internet, or cell phone, but on the road system). A fuel cell was purchased by the National Park Service for installation in their newly constructed visitor center at Exit Glacier in the Kenai Fjords National Park. The DOE participation in this project as initially scoped was for independent verification of the operation of this demonstration. This project met with mixed success. The fuel cell has operated over 6 seasons at the facility with varying degrees of success, with one very good run of about 1049 hours late in the summer of 2006, but in general the operation has been below expectations. There have been numerous stack failures, the efficiency of electrical generation has been lower than expected, and the field support effort required has been far higher than expected. Based on the results to date, it appears that this technology has not developed to the point where demonstrations in off road sites are justified.

  5. [The changes in mental working capacity of operators during 24-hour shift work conditions].

    Science.gov (United States)

    Kal'nysh, V V; Shvets', A V; Ieshchenko, O I

    2011-01-01

    Psychophysiological peculiarities of influence of a 24-hour shift work on the efficiency of operators have been discussed. It was shown that servicemen operators develop significant fatigue as a result of 24 hrs duty services. The informative psychophysiological characteristics which can be reliable indicators of fatigue level are highlighted. Individual psychophysiological indicators of fatigue level, according to different mechanisms of its development, have been proposed. The hypothesis about the existence of several compensatory mechanisms for maintenance of long duty operators' working capacity has been formulated.

  6. Reliability of a Large Series-parallel System in Variable Operating Conditions

    Institute of Scientific and Technical Information of China (English)

    Joanna Soszynska

    2006-01-01

    In this paper, a semi-Markov model of system operation processes is proposed and its selected parameters are determined. A series-parallel multi-state system is considered, and its reliability and risk characteristics found. Subsequently,a joint model of system operation process and system multi-state reliability and risk is constructed. Moreover, the asymptotic approach to reliability and risk evaluation of a multi-state series-parallel system in its operation process is applied to a port grain transportation system.

  7. Effect of operating conditions and reactor configuration on efficiency of full-scale biogas plants

    DEFF Research Database (Denmark)

    Angelidaki, Irini; Boe, Kanokwan; Ellegaard, L.

    2005-01-01

    A study on 18 full-scale centralized biogas plants was carried out in order to find significant operational factors influencing productivity and stability of the plants. It was found that the most plants were operating relatively stable with volatile fatty acids (VFA) concentration below 1.5 g....../l. VFA concentration increase was observed in occasions with dramatic overloading or other disturbances such as operational temperature changes. Ammonia was found to be a significant factor for stability. A correlation between increased residual biogas production and high ammonia was found. When ammonia...

  8. Compensating Operator and Weak Convergence of Semi-Markov Process to the Diffusion Process without Balance Condition

    Directory of Open Access Journals (Sweden)

    Igor V. Malyk

    2015-01-01

    Full Text Available Weak convergence of semi-Markov processes in the diffusive approximation scheme is studied in the paper. This problem is not new and it is studied in many papers, using convergence of random processes. Unlike other studies, we used in this paper concept of the compensating operator. It enables getting sufficient conditions of weak convergence under the conditions on the local characteristics of output semi-Markov process.

  9. Crack growth behaviour of low-alloy steels for pressure boundary components under transient light water reactor operating conditions - CASTOC, Part I: BWR/NWC conditions

    Energy Technology Data Exchange (ETDEWEB)

    Ritter, S.; Seifert, H.P. [Paul Scherrer Institute, PSI, Villigen (Switzerland); Devrient, B.; Roth, A. [Framatome ANP GmbH, Erlangen (Germany); Ehrnsten, U. [VTT Industrial Systems, Espoo (Finland); Ernestova, M.; Zamboch, M. [Nuclear Research Institute, NRI, Rez (Czech Republic); Foehl, J.; Weissenberg, T. [Staatliche Materialpruefungsanstalt, MPA, Stuttgart (Germany); Gomez-Briceno, D.; Lapena, J. [Centro de Investigaciones Energeticas Medioambientales y Tecnologicas, CIEMAT, Madrid (Spain)

    2004-07-01

    One of the ageing phenomena of pressure boundary components of light water reactors (LWR) is environmentally-assisted cracking (EAC). The project CASTOC (5. Framework Programme of the EU) was launched September 2000 with six European partners and terminated August 2003. It was focused in particular on the EAC behaviour of low-alloy steels (LAS) and to some extent to weld metal, heat affected zone and the influence of an austenitic cladding. The main objective was directed to the clarification of EAC crack growth behaviour/mechanism of LAS in high-temperature water under steady-state power operation (constant load) and transient operating conditions (e.g., start-up/shut-down, transients in water chemistry and load). Autoclave tests were performed with Western and Russian type reactor pressure vessel steels under simulated boiling water reactor (BWR)/normal water chemistry (NWC) and pressurised water reactor (VVER) conditions. The investigations were performed with fracture mechanics specimens of different sizes and geometries. The applied loading comprised cyclic loads, static loads and load spectra where the static load was periodically interrupted by partial unloading. With regard to water chemistry, the oxygen content (VVER) and impurities of sulphate and chlorides (BWR) were varied beyond allowable limits for continuous operation. The current paper summarises the most important crack growth results obtained under simulated BWR/NWC conditions. The results are discussed in the context of the current crack growth rate curves in the corresponding nuclear codes. (authors)

  10. Study of safety relief valve operation under ATWS conditions. [Supercritical flow

    Energy Technology Data Exchange (ETDEWEB)

    Hutmacher, E.S.; Whitten, S.D.

    1979-09-01

    In March 1979, the NRC published a report (NUREG/CR-0687) prepared by the Energy Technology Engineering Center (ETEC-TDR-78-19). That report presented a literature survey which updated earlier NRC studies of saturated or subcooled water flow through relief valves, under ATWS conditions. This supplement expands upon that search to include supercritical steam-water flow. No applicable data for the supercritical conditions were found, nor were any newer data on saturated or subcooled conditions uncovered. This supplement also updates a look for facilities currently capable of simultaneously imposing all ATWS conditions upon test relief valves. Results confirmed the negative findings of NUREG/CR-0687.

  11. Study of safety relief valve operation under ATWS conditions. [Super critical flow

    Energy Technology Data Exchange (ETDEWEB)

    Hutmacher, E.S.; Whitten, S.D.

    1979-07-25

    In March 1979, ETEC published as ETEC-TDR-78-19 a search which updated earlier NRC studies of saturated or subcooled water flow through relief valves, under ATWS conditions. This Supplement expands upon that search to include supercritical steam-water flow. No applicable data for the supercritical conditions was found, nor were any newer data on saturated or subcooled conditions uncovered. The Supplement also updated a look for facilities currently capable of simultaneously imposing all ATWS conditions upon test relief valves. Results confirmed the negative findings of ETEC-TDR-78.19.

  12. OPERATIONAL MODAL ANALYSIS OF VEHICLE SYSTEM BASED ON OPERATIONAL CONDITIONS%基于运行工况的车辆系统工作模态分析

    Institute of Scientific and Technical Information of China (English)

    孙志春; 周志立; 李言; 谢基龙; 谢云叶

    2012-01-01

    Based on the theoretical modal parameter analysis method, the modal parameters of one special vehicle system were analyzed first, and then stochastic subspace identification method based on operational conditions was presented to form the estimation formula of operational modal parameters of linear vehicle system. At last, the modal parameters of linear vehicle system were identified by SSI after its vibration test under operational conditions, and were simultaneously compared to the results obtained by the theoretical modal parameter analysis method. Comparison results of the former 8 order operational modals of the vehicle system show discrepancies of 3.86-11.61 percent on modal damping ratios and0. 61 ~ 8.32 percent on modal frequencies, which implies that stochastic subspace identification method based on the operational condition is feasible and effective, and has comparatively higher precision to meet the needs of the analysis of vehicle system under operational conditions.%对运行工况下某一特种车辆系统的模态参数,基于计算模态分析方法进行了计算分析;推导了基于运行工况的该车辆系统随机子空间模态识别算法,得到了其工作模态参数的估算公式.同时,对该车辆系统进行了实际运行工况下的模态识别试验,用上述算法估算公式计算了其工作模态参数,并与计算模态分析结果作了比较.对比结果表明,该车辆系统需要考虑的前8阶工作模态的阻尼比和模态频率等参数的识别结果误差分别为:3.86%~11.61%和0.61%~8.32%,由此说明该识别方法具有较高的识别精度,分析方法可行、有效,能满足运行工况下车辆系统振动分析需要.

  13. 17 CFR 229.303 - (Item 303) Management's discussion and analysis of financial condition and results of operations.

    Science.gov (United States)

    2010-04-01

    ... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false (Item 303) Management's... 1975-REGULATION S-K Financial Information § 229.303 (Item 303) Management's discussion and analysis of..., changes in financial condition and results of operations. Discussions of liquidity and capital resources...

  14. Operation condition for continuous anti-solvent crystallization of CBZ-SAC cocrystal considering deposition risk of undesired crystals

    Science.gov (United States)

    Nishimaru, Momoko; Nakasa, Miku; Kudo, Shoji; Takiyama, Hiroshi

    2017-07-01

    Crystallization operation of cocrystal production has deposition risk of undesired crystals. Simultaneously, continuous manufacturing processes are focused on. In this study, conditions for continuous cocrystallization considering risk reduction of undesired crystals deposition were investigated on the view point of thermodynamics and kinetics. The anti-solvent cocrystallization was carried out in four-component system of carbamazepine, saccharin, methanol and water. From the preliminary batch experiment, the relationships among undesired crystal deposition, solution composition decided by mixing ratio of solutions, and residence time for the crystals were considered, and then the conditions of continuous experiment were decided. Under these conditions, the continuous experiment was carried out. The XRD patterns of obtained crystals in the continuous experiment showed that desired cocrystals were obtained without undesired crystals. This experimental result was evaluated by using multi-component phase diagrams from the view point of the operation point's movement. From the evaluation, it was found that there is a certain operation condition which the operation point is fixed with time in the specific domain without the deposition risk of undesired single component crystals. It means the possibility of continuous production of cocrystals without deposition risk of undesired crystals was confirmed by using multi-component phase diagrams.

  15. 1,3-Propanediol production by Klebsiella oxytoca NRRL-B199 from glycerol. Medium composition and operational conditions

    Directory of Open Access Journals (Sweden)

    Mateusz Wojtusik

    2015-06-01

    Under the best operating conditions, i.e., a programmed variable stirring rate ranging from 50 to 100 rpm and a temperature of 37 °C, a final concentration of 13.5 g/L of 1,3-propanediol with a selectivity of 86% with respect to the glycerol consumed was obtained.

  16. Investigation of the operating conditions to morphology evolution of β-L-glutamic acid during seeded cooling crystallization

    Science.gov (United States)

    Zhang, Fangkun; Liu, Tao; Huo, Yan; Guan, Runduo; Wang, Xue Z.

    2017-07-01

    In this paper the effects of operating conditions including cooling rate, initial supersaturation, and seeding temperature were investigated on the morphology evolution of β-L-glutamic acid (β-LGA) during seeded cooling crystallization. Based on the results of in-situ image acquisition of the crystal morphology evolution during the crystallization process, it was found that the crystal products tend to be plate-like or short rod-like under a slow cooling rate, low initial supersaturation, and low seeding temperature. In the opposite, the operating conditions of a faster cooling rate, higher initial supersaturation, and higher seeding temperature tend to produce long rod-like or needle-like crystals, and meanwhile, the length and width of crystal products will be increased together with a wider crystal size distribution (CSD). The aspect ratio of crystals, defined by the crystal length over width measured from in-situ or sample images, was taken as a shape index to analyze the crystal morphologies. Based on comparative analysis of the experimental results, guidelines on these operating conditions were given for obtaining the desired crystal shapes, along with the strategies for obtaining a narrower CSD for better product quality. Experimental verifications were performed to illustrate the proposed guidelines on the operating conditions for seeded cooling crystallization of LGA solution.

  17. [Hardware-software system for monitoring parameters and characteristics of X-ray computer tomographs under operation conditions].

    Science.gov (United States)

    Blinov, N N; Zelikman, M I; Kruchinin, S A

    2007-01-01

    The results of testing of hardware and software for monitoring parameters (mean number of CT units, noise, field uniformity, high-contrast spatial resolution, layer width, dose) and characteristics (modulation transfer function) of X-ray computer tomographs are presented. The developed hardware and software are used to monitor the stability of X-ray computer tomograph parameters under operation conditions.

  18. Modeling Relevant to Safe Operations of U.S. Navy Vessels in Arctic Conditions: Physical Modeling of Ice Loads

    Science.gov (United States)

    2016-06-01

    Modeling Relevant to Safe Operations of U.S. Navy Vessels in Arctic Conditions.” The program manager was Dr. Paul Hess in Code 331, Structural...of Ice–Structure Interaction. Engineering Fracture Mechanics 68:1923–60. Jordaan, I. J., M. A. Maes, P. W. Brown, and I. P. Hermans . 1993

  19. Evaluation and optimisation of phenomenological multi-step soot model for spray combustion under diesel engine-like operating conditions

    DEFF Research Database (Denmark)

    Pang, Kar Mun; Jangi, Mehdi; Bai, Xue-Song

    2015-01-01

    with the spray combustion solver. Prior to the soot modelling, combustion simulations are carried out. Numerical results show that the ignition delay times and lift-off lengths exhibit good agreement with the experimental measurements across a wide range of operating conditions, apart from those in the cases...

  20. An autonomous operant conditioning automaton%一种自治操作条件反射自动机

    Institute of Scientific and Technical Information of China (English)

    阮晓钢; 戴丽珍; 于乃功; 于建均

    2012-01-01

    针对仿生自主学习控制问题,根据自动机的原理,以操作条件反射学习机制为基础,运用仿生的自组织学习方法,提出一种自治操作条件反射自动机(autonomous operant conditioning automata,AOCA)模型,主要包括:操作集合、状态集合、“条件-操作”规则集合、可观测的状态转移以及操作条件反射学习律;定义了基于AOCA状态取向值的操作熵;给出了AOCA操作熵收敛性证明;分析了AOCA自组织特性;规定了AOCA的递归运行程序.同时,将其应用于斯金纳动物实验的模拟,动物分阶段学习,并且成功习得技能,实验结果表明AOCA实现了模拟操作条件反射学习机制.%To deal with the bionic self-organization learning-control problem, on the basis of the automata principle and the operant conditioning learning mechanism, we make use of the bionic self-organization learning method to build an autonomous operant conditioning automaton (AOCA) model including the action set, the state set, the condition-action rule set, the observed state transition, the operant conditioning learning law as well as a recursive program. We also define the operant entropy based on the orientation values of states in the AOCA model, prove the convergence of the AOCA operant entropy, analyze the self-organization characteristics and develop the recursive operation program for the AOCA. The AOCA model has been applied to simulate the Skinner animal experiment, in which the animal learns the task in stages and succeeds in acquiring the skills eventually. These experiment results demonstrate that the AOCA can realize the learning mechanism of operant conditioning.

  1. Mathematical simulation of the operating emergency conditions for the purpose of energy efficiency increase of thermal power plants management

    Science.gov (United States)

    Gazizova, O. V.; Malafeyev, A. V.; Kondrashova, Y. N.

    2016-04-01

    The regulations of the energy saving policy, being implemented at present, require an enhanced reliability of the power supply systems and operations of the motive loading, actuating machines and mechanisms, for the purpose of reduction of power inputs under operating emergency conditions. The development of industrial units of the distributed generation enables putting the generators, equipped with motors of the comparable power, into the operation, which is non-parallel to a power system. To provide static stability under such conditions the complex approach is required since it allows estimating the stability of the generators and the load during parallel and non-parallel operations with the power system and a complex circuit configuration. The mathematical models of units of the distributed generation and motive loading considering the character of the given mechanism are developed. They are implemented in the software package allowing the operative-dispatch personnel of the industrial power stations to forecast similar modes and develop special measures to provide a stable operation of electrical machines.

  2. Computational Fluid Dynamics Based Investigation of Sensitivity of Furnace Operational Conditions to Burner Flow Controls

    Energy Technology Data Exchange (ETDEWEB)

    Marc Cremer; Dave Wang; Connie Senior; Andrew Chiodo; Steven Hardy; Paul Wolff

    2005-07-01

    This is the Final Technical Report for DOE Cooperative Agreement No: DE-FC26-02NT41580. The goal of this project was to systematically assess the sensitivity of furnace operational conditions to burner air and fuel flows in coal fired utility boilers. The focus of this project was to quantify the potential impacts of ''fine level'' controls rather than that of ''coarse level'' controls (i.e. combustion tuning). Although it is well accepted that combustion tuning will generally improve efficiency and emissions of an ''out of tune'' boiler, it is not as well understood what benefits can be derived through active multiburner measurement and control systems in boiler that has coarse level controls. The approach used here was to utilize existing baseline furnace models that have been constructed using Reaction Engineering International's (REI) computational fluid dynamics (CFD) software. Using CFD analyses provides the ability to carry out a carefully controlled virtual experiment to characterize the sensitivity of NOx emissions, unburned carbon (UBC), furnace exit CO (FECO), furnace exit temperature (FEGT), and waterwall deposition to burner air and fuel flow rates. The Electric Power Research Institute (EPRI) provided co-funding for this program, and instrument and controls experts from EPRI's Instrument and Controls (I&C) Center have been active participants in this project. CFD simulations were completed for five coal fired boilers as planned: (1) 150 MW wall fired, (2) 500 MW opposed wall fired, (3) 600 MW T-Fired, (4) 330 MW cyclone-fired, and (5) 200 MW T-Fired Twin Furnace. In all cases, the unit selections were made in order to represent units that were descriptive of the utility industry as a whole. For each unit, between 25 and 44 furnace simulations were completed in order to evaluate impacts of burner to burner variations in: (1) coal and primary air flow rate, and (2) secondary air flow

  3. Optimization of Sinter Plant Operating Conditions Using Advanced Multivariate Statistics: Intelligent Data Processing

    Science.gov (United States)

    Fernández-González, Daniel; Martín-Duarte, Ramón; Ruiz-Bustinza, Íñigo; Mochón, Javier; González-Gasca, Carmen; Verdeja, Luis Felipe

    2016-08-01

    Blast furnace operators expect to get sinter with homogenous and regular properties (chemical and mechanical), necessary to ensure regular blast furnace operation. Blends for sintering also include several iron by-products and other wastes that are obtained in different processes inside the steelworks. Due to their source, the availability of such materials is not always consistent, but their total production should be consumed in the sintering process, to both save money and recycle wastes. The main scope of this paper is to obtain the least expensive iron ore blend for the sintering process, which will provide suitable chemical and mechanical features for the homogeneous and regular operation of the blast furnace. The systematic use of statistical tools was employed to analyze historical data, including linear and partial correlations applied to the data and fuzzy clustering based on the Sugeno Fuzzy Inference System to establish relationships among the available variables.

  4. Operator health risk evaluation of off-highway dump truck under shovel loading condition

    Institute of Scientific and Technical Information of China (English)

    申焱华; 许敏; 金纯; 高玉; 魏福林

    2015-01-01

    To evaluate the operator health risk exposed to whole-body vibration (WBV) while the electric-shovel loads the ore on the truck body, the semi-truck mathematical model and 3-D virtual prototype were built to simulate the high shockwave of truck cab under the shovel loading. Discrete element method was utilized to accurately estimate the impacting force on the truck body. Based on the ISO 2631-5 criteria, theSed is about 0.56 MPa in both models, which means that the dump operators have a high probability of adverse health effects over long-term exposure to these vibrations. The 4-DOF operator model was built to investigate the biodynamic response of seated-human body exposed to WBV in terms of the transmission of vibrations through the body. The results show that the response peak is in the frequency range of 4−6 Hz corresponding to the primary body resonant frequency.

  5. An investigation of FeCrAl cladding behavior under normal operating and loss of coolant conditions

    Science.gov (United States)

    Gamble, K. A.; Barani, T.; Pizzocri, D.; Hales, J. D.; Terrani, K. A.; Pastore, G.

    2017-08-01

    Iron-chromium-aluminum (FeCrAl) alloys are candidates to be used as nuclear fuel cladding for increased accident tolerance. An analysis of the response of FeCrAl under normal operating and loss of coolant conditions has been performed using fuel performance modeling. In particular, recent information on FeCrAl material properties and phenomena from separate effects tests has been implemented in the BISON fuel performance code and analyses of integral fuel rod behavior with FeCrAl cladding have been performed. BISON simulations included both light water reactor normal operation and loss-of-coolant accidental transients. In order to model fuel rod behavior during accidents, a cladding failure criterion is desirable. For FeCrAl alloys, a failure criterion is developed using recent burst experiments under loss of coolant like conditions. The added material models are utilized to perform comparative studies with Zircaloy-4 under normal operating conditions and oxidizing and non-oxidizing out-of-pile loss of coolant conditions. The results indicate that for all conditions studied, FeCrAl behaves similarly to Zircaloy-4 with the exception of improved oxidation performance. Further experiments are required to confirm these observations.

  6. Experimental Investigation of Zinc Antimonide Thin Film Thermoelectric Element over Wide Range of Operating Conditions

    DEFF Research Database (Denmark)

    Hosseini, Seyed Mojtaba Mir; Rezaniakolaei, Alireza; Blichfeld, Anders Bank

    2017-01-01

    flows in plane with the thin film. At first, the effect of applying different temperatures at the hot side of the specimen is investigated to reach steady state in an open circuit analysis. Then, the study focuses on performance and stability analysis of the thermoelectric element operating under...... different resistive loads and over a wide range of operating temperatures from 160 °C to 350 °C. The results show that, at a hot side temperature equal to 275 °C, the Seebeck coefficient (α) reaches its maximum value (242 μV/K), which is comparable to that of bulk materials reported in the literature...

  7. The Effect of the Operating Conditions on the Apparent Viscosity of Crude Palm Oil During Oil Clarification

    Directory of Open Access Journals (Sweden)

    Sulaiman Al-Zuhair, Mirghani I. Ahmed and Yousif A. Abakr

    2012-10-01

    Full Text Available This paper discusses the apparent viscosity of crude palm oil, using rotary viscometer, under different boundary conditions. It was experimentally shown that the apparent viscosity of palm oil drops with increasing of the shear rate and the temperature.  However, the effect of temperature on the viscosity tends to fade at temperatures beyond 80 oC.  A correlation between the apparent viscosity of crude palm oil and the operating conditions was developed. This correlation can be used in design of crude palm oil settlers and in determining the optimum operating conditions.Key Words:  Crude palm oil, apparent viscosity, shear rate, modelling, separation 

  8. Anaerobic treatment of tequila vinasses under seasonal operating conditions: start-up, normal operation and restart-up after a long stop and starvation period.

    Science.gov (United States)

    Jáuregui-Jáuregui, J A; Méndez-Acosta, H O; González-Álvarez, V; Snell-Castro, R; Alcaraz-González, V; Godon, J J

    2014-09-01

    This study examines the performance of an anaerobic fixed-film bioreactor under seasonal operating conditions prevailing in medium and small size Tequila factories: start-up, normal operation and particularly, during the restart-up after a long stop and starvation period. The proposed start-up procedure attained a stable biofilm in a rather short period (28 days) despite unbalanced COD/N/P ratio and the use of non-acclimated inoculum. The bioreactor was restarted-up after being shut down for 6 months during which the inoculum starved. Even when biofilm detachment and bioreactor clogging were detected at the very beginning of restart-up, results show that the bioreactor performed better as higher COD removal and methane yield were attained. CE-SSCP and Q-PCR analyses, conducted on the biofilm prokaryotic communities for each operating condition, confirmed that the high COD removal results after the bioreactor clogging and the severe starvation period were mainly due to the stable archaeal and resilient bacterial populations.

  9. Combining discrepancy analysis with sensorless signal resampling for condition monitoring of rotating machines under fluctuating operations

    CSIR Research Space (South Africa)

    Heyns, T

    2012-12-01

    Full Text Available for extensive datasets that are representative of different machine fault conditions. The envelope of the filtered signal is referred to as a discrepancy transform, since the discrepancy signal indicates the presence of fault-induced signal distortions...

  10. Prolonged silicon carbide integrated circuit operation in Venus surface atmospheric conditions

    Directory of Open Access Journals (Sweden)

    Philip G. Neudeck

    2016-12-01

    Full Text Available The prolonged operation of semiconductor integrated circuits (ICs needed for long-duration exploration of the surface of Venus has proven insurmountably challenging to date due to the ∼ 460 °C, ∼ 9.4 MPa caustic environment. Past and planned Venus landers have been limited to a few hours of surface operation, even when IC electronics needed for basic lander operation are protected with heavily cumbersome pressure vessels and cooling measures. Here we demonstrate vastly longer (weeks electrical operation of two silicon carbide (4H-SiC junction field effect transistor (JFET ring oscillator ICs tested with chips directly exposed (no cooling and no protective chip packaging to a high-fidelity physical and chemical reproduction of Venus’ surface atmosphere. This represents more than 100-fold extension of demonstrated Venus environment electronics durability. With further technology maturation, such SiC IC electronics could drastically improve Venus lander designs and mission concepts, fundamentally enabling long-duration enhanced missions to the surface of Venus.

  11. The positivity of the difference operator with periodic conditions and its application

    Science.gov (United States)

    Ashyralyev, Allaberen; Tetikoglu, Fatih Sabahattin

    2016-08-01

    In this study, the second order of approximation of the difference operator Ahx with domain which approximates the second order differential dependent operator Ax defined by the formula Axu =-a (x )ux x(x )+δ u (x ),δ ≥0 ,a (x )=a (x +2 π ),x ∈ℝ1 with domain D (Ax)={ u (x ):u (x ),u'(x ),u″(x )∈C (ℝ1 ) ,u (x )=u (x +2 π ),x ∈ℝ1, ∫0 2 π u (x )d x =0 } is presented. The positivity of operator Ahx with domain in the Banach space C (ℝ1 h) is established. It is proved that for any α ∈(0 ,1/2 ) the norms in spaces Ea=Ea(C (ℝ1 h),Ahx) and C2 a(ℝ1 h) are equivalent uniformly with respect to h. The positivity of the operator Ahx with domain in Hölder spaces of C∘ 2 a(ℝ1 h) , α ∈(0 , 1/2) is proved. In application, theorems on well-posedness for difference schemes of the approximate solution of the boundary value problem for elliptic differential equations are presented.

  12. Abrasive wear based predictive maintenance for systems operating in sandy conditions

    NARCIS (Netherlands)

    Woldman, M.; Tinga, T.; Heide, E. van der; Masen, M.A.

    2015-01-01

    Machines operating in sandy environments are damaged by the abrasive action of sand particles that enter the machine and become entrapped between components and contacting surfaces. In the case of the military services the combination of a sandy environment and the wide range of tasks to be fulfille

  13. Exploring the Limits and Utility of Operant Conditioning in the Treatment of Drug Addiction

    Science.gov (United States)

    Silverman, Kenneth

    2004-01-01

    This article describes a research program to develop an operant treatment for cocaine addiction in low-income, treatment-resistant methadone patients. The treatment's central feature is an abstinence reinforcement contingency in which patients earn monetary reinforcement for providing cocaine-free urine samples. Success and failure of this…

  14. Operation of grid-connected DFIG under unbalanced grid voltage condition

    NARCIS (Netherlands)

    Zhou, Y.; Bauer, P.; Ferreira, J.A.; Pierik, J.

    2009-01-01

    Doubly fed induction generator (DFIG) still shares a large part in today's wind power market. It provides the benefits of variable speed operation cost-effectively, and can control its active and reactive power independently. Crowbar protection is often adopted to protect the rotor-side voltage sour

  15. On optimum temperature conditions for operation of portable aliminum-air batteries

    Directory of Open Access Journals (Sweden)

    Vlasenko Maxim

    2017-01-01

    Full Text Available For construction of portable aluminium-air batteries (AABs for field applications the data on performance of such batteries at low temperatures are necessary. Such experimental data are presented in this article. Lower temperature limit for effective operation of portable AABs is estimated. Possibility of AABs self-heating to the desired temperature is also considered.

  16. Operation Indicators of the Rotating-Hearth Furnace in Restrictive Manufacturing Conditions

    Directory of Open Access Journals (Sweden)

    Črnko, J.

    2007-01-01

    Full Text Available The heating operation of the rotating-hearth furnace involving semi-finished steel products was analysed, and specific heat consumption was determined as a function of furnace productivity. The aim was to find out how a change in productivity, which is not accompanied by a modification of the thermal regime, can affect the heating quality and surface oxidation of products.

  17. 42 CFR 417.413 - Qualifying condition: Operating experience and enrollment.

    Science.gov (United States)

    2010-10-01

    ... city whose population exceeds 50,000 individuals. (4) A subdivision or subsidiary of an HMO or CMP that... that it has operating experience and an enrolled population sufficient to provide a reasonable basis... the population. (CMS does not grant a waiver that would permit the percentage of Medicare and...

  18. Dolphin-Assisted Therapy as a Verbal Operant Condition for Children with Autism

    Science.gov (United States)

    Terrasi, Renee Marie

    2007-01-01

    This study examined the effects of Dolphin-Assisted Therapy (DAT) as a reinforcer for verbal operant production in children with Autism Spectrum Disorder. Three children who attended a dolphin therapy program participated in this single subject research study. Baseline data was collected for each child via a video tape provided by parents and…

  19. Performance Availability Assessment of Combined Multi Power Source Traction Drive Considering Real Operational Conditions

    Directory of Open Access Journals (Sweden)

    Frenkel Ilia

    2016-09-01

    Full Text Available The present paper deals with the vehicle’s traction electric drive, consisting of several various electric power sources. One of the main requirements for such systems are the safety and sustainable operations, achieved largely the implementation of an uninterrupted supply of the vehicle’s propulsion system with an electric power.

  20. Numerical investigation of diffuse ceiling ventilation in an office under different operating conditions

    DEFF Research Database (Denmark)

    Hviid, Christian Anker; Petersen, Steffen

    2014-01-01

    is a numerical study of the performance of a six person office equipped with diffuse ventilation ceiling. In total six extreme, yet realistic, operation scenarios were simulated to study the performance including different occupancy, ventilation rates and supply air temperatures. The performance was studied...

  1. Modified Thermodynamic Equilibrium Model for Biomass Gasification: A Study of the Influence of Operating Conditions

    DEFF Research Database (Denmark)

    Puig Arnavat, Maria; Bruno, Juan Carlos; Coronas, Alberto

    2012-01-01

    data from different authors for downdraft, fluidized-bed gasifiers and different biomasses, showing good agreement between reported data and modeled values. In addition, it has been used to evaluate the influence of different operating parameters [equivalence ratio (ER), air preheating, steam injection...

  2. Real Hypersurfaces of Nonflat Complex Projective Planes Whose Jacobi Structure Operator Satisfies a Generalized Commutative Condition

    Directory of Open Access Journals (Sweden)

    Theocharis Theofanidis

    2016-01-01

    Full Text Available Real hypersurfaces satisfying the condition ϕl=lϕ(l=R(·,ξξ have been studied by many authors under at least one more condition, since the class of these hypersurfaces is quite tough to be classified. The aim of the present paper is the classification of real hypersurfaces in complex projective plane CP2 satisfying a generalization of ϕl=lϕ under an additional restriction on a specific function.

  3. Influence of operational conditions on the stability of aerobic granules from the perspective of quorum sensing.

    Science.gov (United States)

    Zhang, Chen; Sun, Supu; Liu, Xiang; Wan, Chunli; Lee, Duu-Jong

    2017-03-01

    Integrated aerobic granules were first cultivated in two sequencing batch reactors (SBRs) (A1 and A2). Then, A1's influent organic loading rate (OLR) was changed from alternating to constant (cycling time was still 6 h), while A2's cycling time varied from 6 to 4 h (influent OLR strategy remained alternating). After 30-day operation since the manipulative alternations, granule breakage happened in two reactors at different operational stages, along with the decrease of granule intensity. Granule diameter in A1 declined from the original 0.84 to 0.32 cm during the whole operation, while granules in A2 dwindled to 0.31 cm on day 22 with similar size to A1. Both the amount of total extracellular polymeric substances (EPSs) and the protein were declining throughout the operation, and the large molecular weight of protein was considered closely related to the stability of aerobic granules. The relative AI-2 level decreased at the same time, and influent OLR strategy might had more evident impact on quorum sensing (QS) ability of sludge compared with starvation period. Combined with microbial results, the decline of total EPS amount in two reactors could be concluded as follows: During the reactor operation, some functional bacteria gradually lost their dominance and were eliminated from the reactors, which finally caused granule disintegration. In summary, the results further confirmed that alternating OLR and proper starvation period were two major factors in effective cultivation and stability of aerobic granules from the perspective of QS.

  4. Wave operators, similarity and dynamics for a class of Schrödinger operators with generic non-mixed interface conditions in 1D

    Energy Technology Data Exchange (ETDEWEB)

    Mantile, Andrea [Laboratoire de Mathématiques, Université de Reims - FR3399 CNRS, Moulin de la Housse BP 1039, 51687 Reims (France)

    2013-08-15

    We consider a simple modification of the 1D-Laplacian where non-mixed interface conditions occur at the boundaries of a finite interval. It has recently been shown that Schrödinger operators having this form allow a new approach to the transverse quantum transport through resonant heterostructures. In this perspective, it is important to control the deformations effects introduced on the spectrum and on the time propagator by this class of non-selfadjoint perturbations. In order to obtain uniform-in-time estimates of the perturbed semigroup, our strategy consists in constructing stationary wave operators allowing to intertwine the modified non-selfadjoint Schrödinger operator with a “physical” Hamiltonian. For small values of a deformation parameter “θ,” this yields a dynamical comparison between the two models showing that the distance between the corresponding semigroups is dominated by ‖θ‖ uniformly in time in the L{sup 2}-operator norm.

  5. Social capital, collective efficacy and the provision of social support services and amenities by municipalities in the Netherlands.

    Science.gov (United States)

    Waverijn, Geeke; Groenewegen, Peter P; de Klerk, Mirjam

    2017-03-01

    Differential provision of local services and amenities has been proposed as a mechanism behind the relationship between social capital and health. The aim of this study was to investigate whether social capital and collective efficacy are related to the provision of social support services and amenities in Dutch municipalities, against a background of decentralisation of long-term care to municipalities. We used data on neighbourhood social capital, collective efficacy (the extent to which people are willing to work for the common good), and the provision of services and amenities in 2012. We included the services municipalities provide to support informal caregivers (e.g. respite care), individual services and support (e.g. domiciliary help), and general and collective services and amenities (e.g. lending point for wheelchairs). Data for social capital were collected between May 2011 and September 2012. Social capital was measured by focusing on contacts between neighbours. A social capital measure was estimated for 414 municipalities with ecometric measurements. A measure of collective efficacy was constructed based on information about the experienced responsibility for the liveability of the neighbourhood by residents in 2012, average charity collection returns in municipalities in 2012, voter turnout at the municipal elections in 2010 and the percentage of blood donors in 2012. We conducted Poisson regression and negative binomial regression to test our hypotheses. We found no relationship between social capital and the provision of services and amenities in municipalities. We found an interaction effect (coefficient = 3.11, 95% CI = 0.72-5.51, P = 0.011) of social capital and collective efficacy on the provision of support services for informal caregivers in rural municipalities. To gain more insight in the relationship between social capital and health, it will be important to study the relationship between social capital and differential provision of

  6. Numerical Simulation of Seepage Field of Tailing Water Channel Under Different Conditions in Operation Period

    Science.gov (United States)

    Wang, Feihan; Yan, Guoxin; Chen, Deling

    According to mathematical model of rock and soil, it calculated seepage field of tailing water channel under different conditions. The results showed that under condition of no.1, the seepage discharge from outside to inside of channel is 0.394 m3/h and the discharge under plastic concrete cut-off is 0.358m3/h, and that under condition of no.2, the seepage discharge from outside to inside of channel is 0.249 m3/h and the discharge under plastic concrete cut-off is 0.236m3/h. Under condition of no.1, the outflow of saturation line is at elevation of 411.0m which is under sand and gravel filling layer and near boundary of drift gravel sand layer. Under condition of no.2, the outflow of saturation line is at elevation of 403.0m which is under drift gravel sand layer and near rock foundation. The results showed that numerical simulation can be used to do with seepage problems of tailing water channel.

  7. Assessment of the Operating Temperature of Crystalline PV Modules Based on Real Use Conditions

    Directory of Open Access Journals (Sweden)

    Giuseppina Ciulla

    2014-01-01

    Full Text Available Determining the operating temperature Tc of photovoltaic panels PV is important in evaluating the actual performance of these systems. In the literature, different correlations exist, in either explicit or implicit forms, which often do not account for the electrical behaviour of panels; in this way, estimating Tc is based only on the passive behaviour of the PV. In this paper, the authors propose a new implicit correlation that takes into account the standard weather variables and the electricity production regimes of a PV panel in terms of the proximity to the maximum power points. To validate its reliability, the new correlation was tested on two different PV panels (Sanyo and Kyocera panels and the results were compared with values obtained from other common correlations already available in the literature. The data show that the quality of the new correlation drastically improves the estimation of the photovoltaic operating temperature.

  8. Condition-based dynamic maintenance operations planning and grouping. Application to commercial heavy vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Bouvard, K., E-mail: keomany.bouvard@volvo.co [Volvo Technology, 99 route de Lyon, 69806 Saint Priest cedex (France); Laboratoire d' Automatique de Genie Informatique et Signal - FRE3303 - Polytech' Lille, 59655 Villeneuve d' Ascq (France); Artus, S., E-mail: samuel.artus@volvo.co [Volvo Technology, 99 route de Lyon, 69806 Saint Priest cedex (France); Berenguer, C., E-mail: christophe.berenguer@utt.f [Universite de technologie de Troyes - Institut Charles Delaunay and UMR CNRS 6279 - 12, rue Marie Curie, BP2060, 10010 Troyes cedex (France); Cocquempot, V., E-mail: vincent.cocquempot@univ-lille1.f [Laboratoire d' Automatique de Genie Informatique et Signal - FRE3303 - Polytech' Lille, 59655 Villeneuve d' Ascq (France)

    2011-06-15

    This paper aims at presenting a method to optimize the maintenance planning for a commercial heavy vehicle. Such a vehicle may be considered as a multi-components system. Grouping maintenance operations related to each component reduces the global maintenance cost of the system. Classically, the optimization problem is solved using a priori reliability characteristics of components. Two types of methods may be used, i.e. static or dynamic methods. Static methods provide a fixed maintenance planning, whereas dynamic methods redefine the groups of maintenance operations at each decision time. Dynamic procedures can incorporate component information such as component states or detected failures. For deteriorating systems, reliability characteristics of each component may be estimated thanks to deterioration models and may be updated when a degradation measure is available. This additional information on degradation features allows to better follow the real state of each component and to improve the maintenance planning.

  9. CERIT air-conditioning system powered by solar energy: Two years of operation

    Energy Technology Data Exchange (ETDEWEB)

    Lazzarin, R.; Romagnoni, P.; Casasola, L. (Bari Univ. (Italy). Ist. di Fisica Tecnica ed Impianti Termotecnici CERIT S.p.A., Pordenone (Italy) Padova Univ. (Italy). Ist. di Fisica Tecnica)

    The largest European solar air conditioner (equipped with 440 square meters of aluminized Myler reflection panels; 440 square meters of Cortec evacuated tube solar collectors; 150 and 43 cubic meter, respectively, cold and hot water storage tanks; 50 kW absorption machine; 4 cylinder compression chiller; and natural gas fired boiler for winter space heating) was built at the CERIT (Regional Technological Research Center) of Pordenone, Italy. This article, with the aid of flowsheets, outlines the plant's key design and operational features, and tables performance and energy consumption data to back up a discussion of the major results achieved during two years of operation. Particular attention is given to the plant's seasonal performance.

  10. Optimization of automotive Rankine cycle waste heat recovery under various engine operating condition

    Science.gov (United States)

    Punov, Plamen; Milkov, Nikolay; Danel, Quentin; Perilhon, Christelle; Podevin, Pierre; Evtimov, Teodossi

    2017-02-01

    An optimization study of the Rankine cycle as a function of diesel engine operating mode is presented. The Rankine cycle here, is studied as a waste heat recovery system which uses the engine exhaust gases as heat source. The engine exhaust gases parameters (temperature, mass flow and composition) were defined by means of numerical simulation in advanced simulation software AVL Boost. Previously, the engine simulation model was validated and the Vibe function parameters were defined as a function of engine load. The Rankine cycle output power and efficiency was numerically estimated by means of a simulation code in Python(x,y). This code includes discretized heat exchanger model and simplified model of the pump and the expander based on their isentropic efficiency. The Rankine cycle simulation revealed the optimum value of working fluid mass flow and evaporation pressure according to the heat source. Thus, the optimal Rankine cycle performance was obtained over the engine operating map.

  11. Thermal modeling of nickel-hydrogen battery cells operating under transient orbital conditions

    Science.gov (United States)

    Schrage, Dean S.

    1991-01-01

    An analytical study of the thermal operating characteristics of nickel-hydrogen battery cells is presented. Combined finite-element and finite-difference techniques are employed to arrive at a computationally efficient composite thermal model representing a series-cell arrangement operating in conjunction with a radiately coupled baseplate and coldplate thermal bus. An aggressive, low-mass design approach indicates that thermal considerations can and should direct the design of the thermal bus arrangement. Special consideration is given to the potential for mixed conductive and convective processes across the hydrogen gap. Results of a compressible flow model are presented and indicate the transfer process is suitably represented by molecular conduction. A high-fidelity thermal model of the cell stack (and related components) indicates the presence of axial and radial temperature gradients. A detailed model of the thermal bus reveals the thermal interaction of individual cells and is imperative for assessing the intercell temperature gradients.

  12. A study on framework for assessing limiting condition for operation(LCOs) quantitatively in a CANDU reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Kyung Min

    2003-02-15

    Limiting conditions for operations define the allowed outage times and the actions to be taken if the repair cannot be completed within the AOT. Typically the actions required are plant shutdown. In situations where the risk associated with the action, i.e., the risk of plant shutdown given a failure in the safety system, may be substantial, a strategy is needed to control the risk implications. In this study the strategy is evaluated quantitatively using a tool of system dynamics. The strategic actions associated with LCO needs to be assessed dynamically. System dynamics technique is easy enough to be applied for quantitative assessment of LCO, where the system dynamics is an important factor in evaluating operational modes of nuclear power plants. The review on the improvements of overly conservative technical specification has been performed in this study. The VENSIM tool has been applied to evaluate quantitatively the LCO of the auxiliary feed water systems in the Wol-Sung nuclear power plant. A value of core damage frequency in PSA is used as risk measure. The analysis of both full power operation and shutdown operation has been compared for the value of the CDF. This study shows a plot of LCO full power operating and shutdown risks in term of core damage probability for failure of AFWS (auxiliary feedwater system). Obtaining a lower risk level in a stable mode, compared to the LCO operation alternative, is the principal motivation of going to full power operational mode or shutdown operational mode. A time dependent framework developed in this study has been applied to assess the LCO of the example problem and it is shown that it is very flexible in that it can be applied to assess LCO quantitatively under any operational context of the technical specifications. This study contributes risk informed regulation to enhance and optimize the LCO of previous technical specifications for CANDU through developing framework in application proposed in this methodology.

  13. New concept for condition management of plants as a result of the KUNTO project. New operations approach reduces costs

    Energy Technology Data Exchange (ETDEWEB)

    McNiven, U.; Tamminen, L.

    1998-07-01

    IVO Generation Services Ltd. has carried out a project at the IVO Naantali power plant to develop the plants condition management. The project defines critical and monitored components for each system. In addition, recommendations for further action, investment proposals and suggestions for changes in maintenance and operations practices were supplied for the various systems in the plant. The systematic approach which was the result of the projects integrated into maintenance and operations practices where data collection and analysis is part of the routine. Up-to-date data is utilized in focusing maintenance and investments, in planning and reporting functions

  14. Necessary and sufficient conditions for boundedness of commutators of the general fractional integral operators on weighted Morrey spaces

    CERN Document Server

    Si, Zengyan

    2012-01-01

    We prove that $b$ is in $Lip_{\\bz}(\\bz)$ if and only if the commutator $[b,L^{-\\alpha/2}]$ of the multiplication operator by $b$ and the general fractional integral operator $L^{-\\alpha/2}$ is bounded from the weighed Morrey space $L^{p,k}(\\omega)$ to $L^{q,kq/p}(\\omega^{1-(1-\\alpha/n)q},\\omega)$, where $0 \\frac{1-k}{p/q-k},$ and here $r_\\omega$ denotes the critical index of $\\omega$ for the reverse H\\"{o}lder condition.

  15. FE-MODELLING OF A CONTACT LAYER BETWEEN ELEMENTS JOINED IN PRELOADED BOLTED CONNECTIONS FOR THE OPERATIONAL CONDITION

    Directory of Open Access Journals (Sweden)

    Rafał Grzejda

    2014-11-01

    Full Text Available Modelling and calculations of a contact layer between elements joined in a preloaded bolted connection for the operational condition are presented. The physical model of the bolted connection is based on a flexible flange element that is joined with a rigid support by means of the no-bolt model (at the assembly stage or the rigid body bolt model (at the operational stage. The contact layer between joined elements is described as the nonlinear Winkler model. The contact joint model considering an experimental normal elastic characteristic is presented. Examples of normal contact pressure and normal contact deformations distributions are contained.

  16. A REVIEW: THE EFFECT OF OPERATING CONDITIONS AND THERMAL MANAGEMENT ON THE PERFORMANCES OF METAL HYDRIDE HYDROGEN STORAGE TANK

    Directory of Open Access Journals (Sweden)

    Taurista Perdana Syawitri

    2016-12-01

    Full Text Available For safety and operability concerns, the use of metal hydrides to store hydrogen appears to be particularly promising option for alternative energy at present. However, the process of adding, removing and distributing heat during the hydrogen charging/ discharging process is problematic due to the poor effective thermal conductivity of the metal hydride porous bed and the high enthalpies of H2 adsorption/desorption. Therefore, heat transfer is a critical factor affecting the performance of metal hydride hydrogen (MHR storage tanks. Over decade, many researches focused on MHR’s operating conditions and its thermal management to improve its performance.

  17. Necessary and Sufficient Conditions for Boundedness of Commutators of the General Fractional Integral Operators on Weighted Morrey Spaces

    Directory of Open Access Journals (Sweden)

    Zengyan Si

    2012-01-01

    Full Text Available We prove that b is in Lipβ(ω if and only if the commutator [b,L-α/2] of the multiplication operator by b and the general fractional integral operator L-α/2 is bounded from the weighted Morrey space Lp,k(ω to Lq,kq/p(ω1-(1-α/nq,ω, where 0(1-k/(p/(q-k, and here rω denotes the critical index of ω for the reverse Hölder condition.

  18. Lumen and Chromaticity Maintenance of LED PAR38 Lamps Operated in Steady-State Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Royer, Michael P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2014-12-01

    The lumen depreciation and color shift of 38 different lamps (32 LED, 2 CFL, 1 ceramic metal halide [CMH], 3 halogen) were monitored in a specially developed automated long-term test apparatus (ALTA2) for nearly 14,000 hours. Five samples of each lamp model were tested, with measurements recorded on a weekly basis. The lamps were operated continuously at a target ambient temperature between 44°C and 45°C.

  19. The effect of contingency upon the appetitive conditioning of free-operant behavior

    OpenAIRE

    Hammond, Lynn J.

    1980-01-01

    The problem of maintaining independence between response rates and reinforcement probabilities when determining the effect of varying the response-reinforcement contingency upon free-operant behavior was solved by programming local reinforcement probabilities for response and no response on a second-by-second basis. Fifty-seven rats were trained to lever-press on schedules of water reinforcement involving different values of contingency. All rats were first trained on a high positive continge...

  20. Detachment 101 and North Burma: Historical Conditions for Future Unconventional Warfare Operations

    Science.gov (United States)

    2016-05-26

    MA: Little, Brown , and Company, 1963), 27. 43 Troy J. Sacquety, The OSS in Burma: Jungle War Against the Japanese (Lawrence, KS: University of Kansas...and operations in the area. To accomplish GEN Stilwell’s guidance, DET 101’s four area commands, FORWARD, PAT , KNOTHEAD, and TRAMP, increased the...William R. and Dean Brelis. Behind the Burma Road: The Story of America’s Most Successful Guerrilla Force. Boston: Little, Brown and Company, 1963

  1. Pathologic and post-operative conditions of the plantar fascia: review of MR imaging appearances.

    Science.gov (United States)

    Yu, J S

    2000-09-01

    Magnetic resonance (MR) imaging has emerged as an important noninvasive diagnostic imaging technique for assessment of foot pathology. This modality, owing to its multiplanar imaging capability and inherent superiority in contrast, has been shown to be more accurate and sensitive for detection of plantar fascia pathology than any other imaging method. One of the most important and recognizable causes of heel pain is plantar fasciitis. With the exception of plantar fasciitis, there has been little emphasis on imaging other conditions that affect this important structure. The objective of this review is to demonstrate, from a perspective of MR imaging, the many different pathologic conditions that affect the plantar fascia. Included in this review will be a discussion of normal anatomy as well as entities such as acute plantar fasciitis, chronic plantar fasciitis, traumatic rupture, normal post-surgical changes, pathologic post-fasciotomy conditions, infection, and fibromatosis.

  2. Pathologic and post-operative conditions of the plantar fascia: review of MR imaging appearances

    Energy Technology Data Exchange (ETDEWEB)

    Yu, J.S. [Ohio State Univ., Columbus (United States). Dept. of Radiology

    2000-09-01

    Magnetic resonance (MR) imaging has emerged as an important noninvasive diagnostic imaging technique for assessment of foot pathology. This modality, owing to its multiplanar imaging capability and inherent superiority in contrast, has been shown to be more accurate and sensitive for detection of plantar fascia pathology than any other imaging method. One of the most important and recognizable causes of heel pain is plantar fasciitis. With the exception of plantar fasciitis, there has been little emphasis on imaging other conditions that affect this important structure. The objective of this review is to demonstrate, from a perspective of MR imaging, the many different pathologic conditions that affect the plantar fascia. Included in this review will be a discussion of normal anatomy as well as entities such as acute plantar fasciitis, chronic plantar fasciitis, traumatic rupture, normal post-surgical changes, pathologic post-fasciotomy conditions, infection, and fibromatosis. (orig.)

  3. Preliminary Survey of Icing Conditions Measured During Routine Transcontinental Airline Operation

    Science.gov (United States)

    Perkins, Porter J.

    1952-01-01

    Icing data collected on routine operations by four DC-4-type aircraft equipped with NACA pressure-type icing-rate meters are presented as preliminary information obtained from a statistical icing data program sponsored by the NACA with the cooperation of many airline companies and the United States Air Force. The program is continuing on a much greater scale to provide large quantities of data from many air routes in the United States and overseas. Areas not covered by established air routes are also being included in the survey. The four aircraft which collected the data presented in this report were operated by United Air Lines over a transcontinental route from January through May, 1951. An analysis of the pressure-type icing-rate meter was satisfactory for collecting statistical data during routine operations. Data obtained on routine flight icing encounters from.these four instrumented aircraft, although insufficient for a conclusive statistical analysis, provide a greater quantity and considerably more realistic information than that obtained from random research flights. A summary of statistical data will be published when the information obtained daring the 1951-52 icing season and that to be obtained during the 1952-53 season can be analyzed and assembled. The 1951-52 data already analyzed indicate that the quantity, quality, and range of icing information being provided by this expanded program should afford a sound basis for ice-protection-system design by defining the important meteorological parameters of the icing cloud.

  4. Assessment of the operating conditions of coordinated Q-V controller within secondary voltage control system

    Directory of Open Access Journals (Sweden)

    Arnautović Dušan

    2014-01-01

    Full Text Available The paper, discusses the possibility to use coordinated Q-V controller (CQVC to perform secondary voltage control at the power plant level. The CQVC performs the coordination of the synchronous generators' (SG reactive power outputs in order to maintain the same total reactive power delivered by the steam power plant (SPP, while at the same time maintaining a constant voltage with programmed reactive droop characteristic at the SPP HV busbar. This busbar is the natural pilot node for secondary voltage control at HV level as the node with maximum power production and maximum power consumption. In addition to voltage control, the CQVC maintains the uniform allocation of reactive power reserves at all SGs in the power plant. This is accomplished by setting the reactive power of each SG at given operating point in accordance to the available reactive power of the same SG at that point. Different limitations imposed by unit's and plant equipment are superimposed on original SG operating chart (provided by the manufacturer in order to establish realistic limits of SG operation at given operating point. The CQVC facilitates: i practical implementation of secondary voltage control in power system, as it is capable of ensuring delivery of reactive power as requested by regional/voltage control while maintaining voltage at system pilot node, ii the full deployment of available reactive power of SGs which in turn contributes to system stability, iii assessment of the reactive power impact/contribution of each generator in providing voltage control as ancillary service. Furthermore, it is also possible to use CQVC to pricing reactive power production cost at each SG involved and to design reactive power bidding structure for transmission network devices by using recorded data. Practical exploitation experience acquired during CQVC continuous operation for over two years enabled implementation of the optimal setting of reference voltage and droop on daily

  5. Extending the application range of a fuel performance code from normal operating to design basis accident conditions

    Science.gov (United States)

    Van Uffelen, P.; Győri, C.; Schubert, A.; van de Laar, J.; Hózer, Z.; Spykman, G.

    2008-12-01

    Two types of fuel performance codes are generally being applied, corresponding to the normal operating conditions and the design basis accident conditions, respectively. In order to simplify the code management and the interface between the codes, and to take advantage of the hardware progress it is favourable to generate a code that can cope with both conditions. In the first part of the present paper, we discuss the needs for creating such a code. The second part of the paper describes an example of model developments carried out by various members of the TRANSURANUS user group for coping with a loss of coolant accident (LOCA). In the third part, the validation of the extended fuel performance code is presented for LOCA conditions, whereas the last section summarises the present status and indicates needs for further developments to enable the code to deal with reactivity initiated accident (RIA) events.

  6. Application of the quantitative oil monitoring to analysing the operating condition of marine machinery

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Based on the data of Fourier transform infra-red (FTIR) spectroscopy, spectrometric oilanalysis (SOA) and other routine methods, the experiment of oil monitoring for steering propellersis discussed. The experiment demonstrates the FTIR spectroscopy can rapidly and easily obtainthe results in laboratory analysis, and combine with spectrometer oil analysis, complementary in-formation is most effective to condition monitoring of marine machinery.

  7. Nafion-porous cerium oxide nanotubes composite membrane for polymer electrolyte fuel cells operated under dry conditions

    Science.gov (United States)

    Ketpang, Kriangsak; Oh, Kwangjin; Lim, Sung-Chul; Shanmugam, Sangaraju

    2016-10-01

    A composite membrane operated in polymer electrolyte fuel cells (PEFCs) under low relative humidity (RH) is developed by incorporating cerium oxide nanotubes (CeNT) into a perfluorosulfonic acid (Nafion®) membrane. Porous CeNT is synthesized by direct heating a precursor impregnated polymer fibers at 500 °C under an air atmosphere. Compared to recast Nafion and commercial Nafion (NRE-212) membranes, the Nafion-CeNT composite membrane generates 1.1 times higher power density at 0.6 V, operated at 80 °C under 100% RH. Compared to Nafion-cerium oxide nanoparticles (Nafion-CeNP) membrane, the Nafion-CeNT provides 1.2 and 1.7 times higher PEFC performance at 0.6 V when operated at 80 °C under 100% and 18% RH, respectively. Additionally, the Nafion-CeNT composite membrane exhibits a good fuel cell operation under 18% RH at 80 °C. Specifically, the fluoride emission rate of Nafion-CeNT composite membrane is 20 times lower than that of the commercial NRE-212 membrane when operated under 18% RH at 80 °C for 96 h. The outstanding PEFC performance and durability operated under dry conditions is mainly attributed to the facile water diffusion capability as well as the effective hydroxyl radical scavenging property of the CeNT filler, resulting in significantly mitigating both the ohmic resistance and Nafion membrane degradation.

  8. An under-operation diagnostic apparatus for motor-operated valve. Technical trends on motor-operated valve conservation for nuclear power stations and condition based maintenance using the new diagnostic apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Itou, Haruo [Japan Atomic Power Co., Tokyo (Japan)

    2002-08-01

    A new motor-operated valve diagnostic analysis system (MOVDAS) can be, in short time, simply and with high precision, carried out diagnosis on deterioration and accident of motor-operated valves with many numbers used for separated and feeding valves important for safety of a nuclear reactor, not only at cease but also under operation of a power plant, and is technology capable of upgrading reliability on a motor-operated valve for a condition based maintenance tool and reducing conservation cost. MOVDAS is composed of a built-in torque sensor directly measurable transit torque behaviors with high precision by upgrading a torque sensing technology using strain gauges and a diagnostic apparatus to analyze their signals, which can be used even under operation of the valves. And, this technology can be adapted for under-operation integrity recognition of the valve recommended by NRC in U.S.A. and for operation and maintenance indication, JEAG-4803 in Japan. Here were introduced its contents and also a motor-operated valve remote diagnostic system recently developed in parallel. (G.K.)

  9. Exposure to histone deacetylase inhibitors during Pavlovian conditioning enhances subsequent cue-induced reinstatement of operant behavior.

    Science.gov (United States)

    Ploense, Kyle L; Kerstetter, Kerry A; Wade, Matthew A; Woodward, Nicholas C; Maliniak, Dan; Reyes, Michael; Uchizono, Russell S; Bredy, Timothy W; Kippin, Tod E

    2013-06-01

    Histone deacetylase inhibitors (HDACIs) strengthen memory following fear conditioning and cocaine-induced conditioned place preference. Here, we examined the effects of two nonspecific HDACIs, valproic acid (VPA) and sodium butyrate (NaB), on appetitive learning measured by conditioned stimulus (CS)-induced reinstatement of operant responding. Rats were trained to lever press for food reinforcement and then injected with VPA (50-200 mg/kg, i.p.), NaB (250-1000 mg/kg, i.p.), or saline vehicle (1.0 ml/kg), 2 h before receiving pairings of noncontingent presentation of food pellets preceded by a tone+light cue CS. Rats next underwent extinction of operant responding followed by response-contingent re-exposure to the CS. Rats receiving VPA (100 mg/kg) or NaB (1000 mg/kg) before conditioning displayed significantly higher cue-induced reinstatement than did saline controls. Rats that received either vehicle or VPA (100 mg/kg) before a conditioning session with a randomized relation between presentation of food pellets and the CS failed to show subsequent cue-induced reinstatement with no difference between the two groups. These findings indicate that, under certain contexts, HDACIs strengthen memory formation by specifically increasing the associative strength of the CS, not through an increasing motivation to seek reinforcement.

  10. conditions

    Directory of Open Access Journals (Sweden)

    M. Venkatesulu

    1996-01-01

    Full Text Available Solutions of initial value problems associated with a pair of ordinary differential systems (L1,L2 defined on two adjacent intervals I1 and I2 and satisfying certain interface-spatial conditions at the common end (interface point are studied.

  11. Dynamic characteristics of a VK-50 reactor operating under conditions of the loss of a normal feedwater flow

    Science.gov (United States)

    Semidotskiy, I. I.; Kurskiy, A. S.

    2013-12-01

    The paper describes the conditions of the ATWS type with virtually complete cessation of the feed-water flow at the operating power level of a reactor of the VK-50 type. Under these conditions, the role of spatial kinetics in the system of feedback between thermohydraulic and nuclear processes with bulk boiling of the coolant in the reactor core is clearly seen. This feature determines the specific character of experimental data obtained and the suitability of their use for verification of the associated codes used for calculating water-water reactors.

  12. Technological indicators of operation of the rotating-hearth furnace in conditions of discontinued production

    Directory of Open Access Journals (Sweden)

    Lazić, L.

    2008-04-01

    Full Text Available Quality heating of the steel charge to be rolled into seamless tubes in the rotating-hearth furnace requires continuous operation of the pilger mill. Interruption of the charging schedule leads to impaired charge heating process. Prolonged heating time causes a rise in the charge temperature above the limit values, and that in turn brings to a larger quantity of scale formed on the charge surface. Final result is loss of metal and overheating of the charge accompanied by increased fuel consumption and lower furnace productivity.

  13. Macroscopic mass and energy balance of a pilot plant anaerobic bioreactor operated under thermophilic conditions.

    Science.gov (United States)

    Espinosa-Solares, Teodoro; Bombardiere, John; Chatfield, Mark; Domaschko, Max; Easter, Michael; Stafford, David A; Castillo-Angeles, Saul; Castellanos-Hernandez, Nehemias

    2006-01-01

    Intensive poultry production generates over 100,000 t of litter annually in West Virginia and 9 x 10(6) t nationwide. Current available technological alternatives based on thermophilic anaerobic digestion for residuals treatment are diverse. A modification of the typical continuous stirred tank reactor is a promising process being relatively stable and owing to its capability to manage considerable amounts of residuals at low operational cost. A 40-m3 pilot plant digester was used for performance evaluation considering energy input and methane production. Results suggest some changes to the pilot plant configuration are necessary to reduce power consumption although maximizing biodigester performance.

  14. Reliability, risk and availability analysis and evaluation of a port oil pipeline transportation system in constant operation conditions

    Energy Technology Data Exchange (ETDEWEB)

    Kolowrocki, Krzysztof [Gdynia Maritime University, Gdynia (Poland)

    2009-07-01

    In the paper the multi-state approach to the analysis and evaluation of systems' reliability, risk and availability is practically applied. Theoretical definitions and results are illustrated by the example of their application in the reliability, risk and availability evaluation of an oil pipeline transportation system. The pipeline transportation system is considered in the constant in time operation conditions. The system reliability structure and its components reliability functions are not changing in constant operation conditions. The system reliability structure is fixed with a high accuracy. Whereas, the input reliability characteristics of the pipeline components are not sufficiently exact because of the lack of statistical data necessary for their estimation. The results may be considered as an illustration of the proposed methods possibilities of applications in pipeline systems reliability analysis. (author)

  15. Operational Circular No.2 (Rev. 2) - Conditions of access to the fenced parts of the CERN site

    CERN Multimedia

    2014-01-01

    Operational Circular No. 2 (Rev. 2) entitled “Conditions of access to the fenced parts of the CERN site” and its “implementation measures”, approved by the Director-General following discussion at the Standing Concertation Committee meeting on 20 May 2014 and entering into force on 1 September 2014, are available on the intranet site of the Human Resources Department (see here).   This circular is applicable to members of the personnel and other persons concerned. It cancels and replaces Operational Circular No. 2 (Rev. 1) entitled “Conditions of access to the fenced parts of the CERN site”, of April 1998. In particular, the revised circular provides for the possibility of mandating a person responsible for the proper implementation of the circular, specifies the rules relating to vehicles allowed on the site and the respective responsibilities of their owners, and relaxes certain administrative formalities in case of loss, theft or di...

  16. The Effect of Influent Characteristics and Operational Conditions over the Performance and Microbial Community Structure of Partial Nitritation Reactors

    Directory of Open Access Journals (Sweden)

    Alejandro Rodriguez-Sanchez

    2014-06-01

    Full Text Available Nitrogen is a main contaminant of wastewater worldwide. Novel processes for nitrogen removal have been developed over the last several decades. One of these is the partial nitritation process. This process includes the oxidation of ammonium to nitrite without the generation of nitrate. The partial nitritation process has several advantages over traditional nitrification-denitrification processes for nitrogen removal from wastewaters. In addition, partial nitritation is required for anammox elimination of nitrogen from wastewater. Partial nitritation is affected by operational conditions and substances present in the influent, such as quinolone antibiotics. In this review, the impact that several operational conditions, such as temperature, pH, dissolved oxygen concentration, hydraulic retention time and solids retention time, have over the partial nitritation process is covered. The effect of quinolone antibiotics and other emerging contaminants are discussed. Finally, future perspectives for the partial nitritation process are commented upon.

  17. Operational Circular No. 2 (Rev. 3) - Conditions of access to the fenced parts of the CERN site

    CERN Multimedia

    HR Department

    2015-01-01

    Operational Circular No. 2 (Rev. 3) entitled "Conditions of access to the fenced parts of the CERN site", approved by the Director-General following discussion in the Standing Concertation Committee meeting on 24 September 2015, is now available via this link.   This revised circular cancels and replaces Operational Circular No. 2 (Rev. 2) also entitled "Conditions of access to the fenced parts of the CERN site", of September 2014. The circular was revised predominantly in order to specify that access to the CERN site is granted to CERN Pension Fund beneficiaries only provided that they are actually in receipt of payments from the Fund; and to allow the Director-General to permit special types of vehicles on site, such as trailers. It also includes a certain number of text improvements and an updated version of the implementation measures, in particular with regard to vehicle identification, road traffic and parking.  

  18. Operating and Loading Conditions of a Three-Level Neutral-Point-Clamped Wind Power Converter Under Various Grid Faults

    DEFF Research Database (Denmark)

    Ma, Ke; Liserre, Marco; Blaabjerg, Frede

    2014-01-01

    In order to fulfill the growing demands from the grid side, full-scale power converters are becoming popular in the wind turbine system. The low-voltage ride-through (LVRT) requirements may not only cause control problems but also result in overstressed components for the power converter. However......, the thermal loading of the wind power converter under various grid faults is still not yet clarified, particularly at megawatt power level. In this paper, the impacts by three types of grid faults to a three-level neutral-point-clamped (3L-NPC) wind power converter in terms of operating and loading conditions...... are analytically solved and simulated. It has been found that the operating and loading conditions of the converter under LVRT strongly depend on the types/severity values of grid voltage dips and also the chosen control algorithms. The thermal distribution among the three phases of the converter may be quite...

  19. HOW JOINT IS JOINT FOREST PRODUCTION: AN ECONOMETRIC ANALYSIS OF TIMBER SUPPLY CONDITIONAL ON ENDOGENOUS AMENITY VALUES. (R828785)

    Science.gov (United States)

    The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

  20. Enzymatic AND logic gates operated under conditions characteristic of biomedical applications.

    Science.gov (United States)

    Melnikov, Dmitriy; Strack, Guinevere; Zhou, Jian; Windmiller, Joshua Ray; Halámek, Jan; Bocharova, Vera; Chuang, Min-Chieh; Santhosh, Padmanabhan; Privman, Vladimir; Wang, Joseph; Katz, Evgeny

    2010-09-23

    Experimental and theoretical analyses of the lactate dehydrogenase and glutathione reductase based enzymatic AND logic gates in which the enzymes and their substrates serve as logic inputs are performed. These two systems are examples of the novel, previously unexplored class of biochemical logic gates that illustrate potential biomedical applications of biochemical logic. They are characterized by input concentrations at logic 0 and 1 states corresponding to normal and pathophysiological conditions. Our analysis shows that the logic gates under investigation have similar noise characteristics. Both significantly amplify random noise present in inputs; however, we establish that for realistic widths of the input noise distributions, it is still possible to differentiate between the logic 0 and 1 states of the output. This indicates that reliable detection of pathophysiological conditions is indeed possible with such enzyme logic systems.