PIXE analysis of ancient Chinese Changsha porcelain

International Nuclear Information System (INIS)

Lin, E.K.; Yu, Y.C.; Wang, C.W.; Liu, T.Y.; Wu, C.M.; Chen, K.M.; Lin, S.S.

1999-01-01

In this work, proton induced X-ray emission (PIXE) method was applied for the analysis of ancient Chinese Changsha porcelain produced in the Tang dynasty (AD 618-907). A collection of glazed potsherds was obtained in the complex of the famous kiln site at Tongguan, Changsha city, Hunan province. Studies of elemental composition were carried out on ten selected Changsha potsherds. Minor and trace elements such as Ti, Mn, Fe, Co, Cu, Rb, Sr, and Zr in the material of the porcelain glaze were determined. Variation of these elements from sample to sample was investigated. Details of results are presented and discussed

PIXE analysis of ancient Chinese Changsha porcelain

Energy Technology Data Exchange (ETDEWEB)

Lin, E.K.; Yu, Y.C.; Wang, C.W.; Liu, T.Y.; Wu, C.M.; Chen, K.M.; Lin, S.S

1999-04-02

In this work, proton induced X-ray emission (PIXE) method was applied for the analysis of ancient Chinese Changsha porcelain produced in the Tang dynasty (AD 618-907). A collection of glazed potsherds was obtained in the complex of the famous kiln site at Tongguan, Changsha city, Hunan province. Studies of elemental composition were carried out on ten selected Changsha potsherds. Minor and trace elements such as Ti, Mn, Fe, Co, Cu, Rb, Sr, and Zr in the material of the porcelain glaze were determined. Variation of these elements from sample to sample was investigated. Details of results are presented and discussed.

PIXE analysis of ancient Chinese Changsha porcelain

Science.gov (United States)

Lin, E. K.; Yu, Y. C.; Wang, C. W.; Liu, T. Y.; Wu, C. M.; Chen, K. M.; Lin, S. S.

1999-04-01

In this work, proton induced X-ray emission (PIXE) method was applied for the analysis of ancient Chinese Changsha porcelain produced in the Tang dynasty (AD 618-907). A collection of glazed potsherds was obtained in the complex of the famous kiln site at Tongguan, Changsha city, Hunan province. Studies of elemental composition were carried out on ten selected Changsha potsherds. Minor and trace elements such as Ti, Mn, Fe, Co, Cu, Rb, Sr, and Zr in the material of the porcelain glaze were determined. Variation of these elements from sample to sample was investigated. Details of results are presented and discussed.

A comparison on the flexural strength of a new dental porcelain (D.} Dentin with Vita company Dentin porcelain (VMK 68N

Directory of Open Access Journals (Sweden)

Ghahramanloo A.

2004-06-01

Full Text Available Statement of Problem: Dental porcelain is one of the best materials ever used in dentistry. Excellent tissue"ncompatibility, esthetics, very low solubility in oral fluids, high compressive strength, and the lowest bacterial"nplaque accumulation on the glazed porcelain are some of its advantages. Porcelain brittleness due to its low"ntensile strength, impact strength and the occlusal attrition of opposing teeth enamel are some of its"ndisadvantages. The most important mechanical properties of dental porcelains are their flexural strength that is"nthe ability of a porcelain to resist fracture when loaded from above. Different ways have been proposed to"neliminate porcelain brittleness and develop its flexural strength, among which baking porcelain on a metal"nframework is more commonly used."nPurpose: Considering that restoration and replacement of teeth by porcelain fused to metal restorations is still"nthe most commonly used technique, the aim of the present study was to measure the flexural strength of a"nporcelain bonded to metal powder, D4 Dentin, and to compare it with Vita Dentin powder."nMaterials and Methods: In this experimental study, a stainless steel box, 25x5x2mm was made according to"nISO 6872: 1995 (E Standard and filled with D4 Dentin powder and Vita Dentin (VMK 68N and baked in"nVita furnace. Then 10 blocks of D^ Dentin and 10 of Vita Dentin were made. Samples were placed on the"nthree point bending test machine and force was applied the middle of each block. To analyze the data, t-"nstudent test and co-variance analysis were used."nResults: Mean flexural strength of D4 Dentin was 53.40±1.35 MPa and that of Vita Dentin was 53.86+7.38"nMPa. The difference was not statistically significant."nConclusion: According to ISO 6872: 1995 (E standard, the flexural strength of all D4 Dentin samples were"ngreater than 50 Mpa.

The TL dating of ancient porcelain

International Nuclear Information System (INIS)

Leung, P.L.; Stokes, M.J.; Wang Weida; Xia Junding; Zhou Zhixin

1997-01-01

The age determination of ancient porcelain using the pre-dose technique in TL dating was reported. The variation of beta dose with depth below the surface of the porcelain slice, the thermal activation characteristic (TAC) for 110 degree C peak, the measurement of paleodose and the estimation of annual dose were studied. The results show that this technique is suitable for authenticity testing of ancient porcelain, but both accuracy and precision for porcelain dating are worse than those for pottery, because porcelain differs from pottery on composition, structure and firing temperature. Besides, some complicated factors in the pre-dose technique would be the possible cause of the greater errors

Effect of metal opaquer on the final color of 3 ceramic crown types on 3 abutment configurations.

Science.gov (United States)

Arif, Rabia; Yilmaz, Burak; Mortazavi, Aras; Ozcelik, Tuncer B; Johnston, William M

2018-04-30

The effect of a recently introduced metal opaquer when used to mask the color of a titanium abutment under ceramic crown systems is unknown. The purpose of this study was to compare the color coordinates of 3 ceramic crown types-characterized monolithic lithium disilicate (LDC) (IPS e.max; Ivoclar Vivadent AG), layered lithium disilicate (LDL) (IPS e.max; Ivoclar Vivadent AG), and layered zirconia (ZL) (H.C. Starck)-on 3 abutment configurations, nonopaqued titanium (Ti), resin opaqued titanium (Op), and zirconia (Zir). In addition, the color differences (CIEDE2000) were evaluated among the 3 crown types on 3 different abutment substrates. Ten Ti disks (10×1 mm) were fabricated with computer-aided design and computer-aided manufacturing (CAD-CAM) to represent the Ti abutments. Five Ti specimens were opaqued (Op) (whiteMetal Opaquer wMO; Blue Sky Bio), and 5 were not opaqued (Ti). Ten zirconia disks were fabricated with CAD-CAM and sintered (10×1.2 mm). Five disks were used as backings to represent Zir abutments, and 5 disks were layered with 1 mm of porcelain (B1, IPS e.Max Ceram; Ivoclar Vivadent AG) to represent layered zirconia crowns (ZL). Ten lithium disilicate plates (14×14×1.2 mm) were sectioned from CAD blocks (B1 IPS e.Max CAD; Ivoclar Vivadent AG). Five plates were layered with the same porcelain (B1, 1 mm), and 5 plates were surface characterized and glazed. An LDL crown on a Zir abutment configuration was used as the control. The 3 simulated crown types (n=5) were optically connected to each of the 3 abutment types, and the color of the 9 groups was measured using a spectroradiometer. Measured data were reported in CIELab coordinates. CIELab data were used to calculate color differences between the control and the 8 experimental groups. Color data were summarized for each group, and analyzed by repeated-measures ANOVA. For pairwise comparisons, a Bonferroni correction of t tests was used, and for interpretive analysis of resulting color difference

Evidence of yttrium silicate inclusions in YSZ-porcelain veneers.

Science.gov (United States)

Stoner, Brian R; Griggs, Jason A; Neidigh, John; Piascik, Jeffrey R

2014-04-01

This report introduces the discovery of crystalline defects that can form in the porcelain veneering layer when in contact with yttria-stabilized zirconia (YSZ). The focus was on dental prostheses and understanding the defects that form in the YSZ/porcelain system; however the data reported herein may have broader implications toward the use and stability of YSZ-based ceramics in general. Specimens were cut from fully sintered YSZ plates and veneering porcelain was applied (X-ray (EDAX) was used for microstructural and elemental analysis. EDAX, for chemical analysis and transmission electron diffraction (TED) for structural analysis were both performed in the transmission electron microscope (TEM). Additionally, in order to spatially resolve Y-rich precipitates, micro-CT scans were conducted at varying depths within the porcelain veneer. Local EDAX (SEM) was performed in the regions of visible inclusions and showed significant increases in yttrium concentration. TEM specimens also showed apparent inclusions in the porcelain and selected area electron diffraction was performed on these regions and found the inclusions to be crystalline and identified as either yttrium-silicate (Y2 SiO5 ) or yttrium-disilicate (Y2 Si2 O7 ). Micro-CT data showed that yttrium-silicate precipitates were distributed throughout the thickness of the porcelain veneer. Future studies are needed to determine whether many of the premature failures associated with this materials system may be the result of crystalline flaws that form as a result of high temperature yttrium diffusion near the surfaces of YSZ. © 2013 Wiley Periodicals, Inc.

Multinationality and Opaqueness

DEFF Research Database (Denmark)

Aabo, Tom; Pantzalis, Christos; Park, Jung Chul

2015-01-01

We investigate whether and how multinationality affects the opaqueness of the firm. We use multiple alternative measurements of multinationality and opaqueness. Spanning nearly three decades for a large sample of US non-financial firms, we find a statistically and economically significant, positi...

The provenance investigation on ancient chinese Ru porcelains by NAA

International Nuclear Information System (INIS)

Gao Zhengyao; Wang Jie; Chen Songhua

1997-01-01

The 28 samples of glazes and bodies of ancient Chinese Ru porcelains are analyzed by neutron activation. The 36 element contents in each sample are determined. The neutron activation analysis (NAA) data are analyzed by fuzzy cluster. The trend cluster diagram is obtained. The result shows that the ancient Chinese Ru porcelains were most probably from the same raw material source though they were from different time, fired in different kilns and in different colors. The near provenance relation between ancient Jun porcelain and ancient Ru porcelain is preliminarily analyzed. The two modern Ru porcelains approximate to ancient Ru porcelains, one becomes estranged from ancient Ru porcelains. Jingdezhen porcelain is unconcerned with Ru porcelains

The Earliest Chinese Proto-Porcelain Excavated from Kiln Sites: An Elemental Analysis.

Science.gov (United States)

Li, Yu; Zhang, Bin; Cheng, Huansheng; Zheng, Jianming

2015-01-01

In June 2012, the Piaoshan kiln site was excavated in Huzhou, Zhejiang Province, which hitherto proved to be the earliest known Chinese proto-porcelain kiln. Judging from the decorative patterns of unearthed impressed stoneware and proto-porcelain sherds, the site was determined to date to the late Xia (c. 2070-c. 1600 BC), the first dynasty of China. Here, we report on proton-induced X-ray emission analyses of 118 proto-porcelain and 35 impressed stoneware sherds from Piaoshan and five subsequent kiln sites in the vicinity. Using principal components analysis on the major chemical compositions, we reveal the relationships between impressed stoneware and proto-porcelain samples from the six kiln sites. The sherds from different sites have distinctive chemical profiles. The results indicate that the raw materials were procured locally. We find a developmental tendency for early glazes towards mature calcium-based glaze. It is most likely that woody plant ashes with increased calcia-potash ratios were applied to the formula.

The Earliest Chinese Proto-Porcelain Excavated from Kiln Sites: An Elemental Analysis.

Directory of Open Access Journals (Sweden)

Yu Li

Full Text Available In June 2012, the Piaoshan kiln site was excavated in Huzhou, Zhejiang Province, which hitherto proved to be the earliest known Chinese proto-porcelain kiln. Judging from the decorative patterns of unearthed impressed stoneware and proto-porcelain sherds, the site was determined to date to the late Xia (c. 2070-c. 1600 BC, the first dynasty of China. Here, we report on proton-induced X-ray emission analyses of 118 proto-porcelain and 35 impressed stoneware sherds from Piaoshan and five subsequent kiln sites in the vicinity. Using principal components analysis on the major chemical compositions, we reveal the relationships between impressed stoneware and proto-porcelain samples from the six kiln sites. The sherds from different sites have distinctive chemical profiles. The results indicate that the raw materials were procured locally. We find a developmental tendency for early glazes towards mature calcium-based glaze. It is most likely that woody plant ashes with increased calcia-potash ratios were applied to the formula.

A.K. SPIESS. LIFE, DEVOTED TO PORCELAIN

Directory of Open Access Journals (Sweden)

Екатерина Сергеевна Хмельницкая

2014-02-01

Full Text Available The article reconstructs the creative biography of the sculptor of the Imperial Porcelain Factory A.K. Spiess, development of his career in Russia. Over the 47 years he was the Chief sculptor of the porcelain factory and was the author of most of the figures created during the "historicism." The article investigates his creative activity, historical and cultural conditions of the development of the porcelain sculpture under his leadership. The author examines in detail the identity of the sculptor, the evolution of his creative activity, discusses the key factors in the development of his career. After four years after arriving in Russia, a former student and assistant sculptor received a position of the chief sculptor of the Imperial Porcelain Factory. Spies managed to perfectly flatter the taste of the Empress Maria, skillfully using the latest achievements of porcelain production, sculptor borrowed from Europe. Due to the great diversity of Spies, it should be noted porcelain amazing adaptability to any changes in the art of Historicism, where one style of fashion rapidly replaced by others. Porcelain Spies "successfully coped with any role": central interior decoration, household items, personal preferences, or evidence of the imperial status of the owner. Author concludes that the "secret" so successful creative activity of August Spiess, who for decades defined the artistic policy sculpture department, consists in the fact that his art was not just on time and responded to the artistic needs of the society. "From porcelain man can do everything" - said I.-I. Candler, whom Europe obliged the birth of porcelain. This phrase is also the key to the art of A. K Spiess.DOI: http://dx.doi.org/10.12731/2218-7405-2014-1-5

Bonding brackets to porcelain: in vitro study

Directory of Open Access Journals (Sweden)

Sant'Anna Eduardo Franzotti

2002-01-01

Full Text Available The aim of this research was to verify, in vitro, the effect of various porcelain surface treatments on the shear strength of orthodontic brackets bonded to porcelain and the mode of fracture after debonding. Eighty-eight samples of metallic supported feldspathic porcelain were randomly divided into four groups according to their surface preparation as follows: the porcelain was maintained intact (GI, roughened with a diamond bur (GII, etched with 10% hydrofluoric acid (GIII, or sandblasted with aluminum oxide (GIV. The specimens were treated with silane (Scothprime and brackets were bonded with Concise. Each sample was subjected to a shear load at a crosshead speed of 1 mm/min and a recording was made at the point of failure. Bond strengths, adequate to withstand the application of orthodontic forces, were achieved in all groups. The Kruskal-Wallis statistical test showed no significant differences in bond strength between the groups (p>0.05. However, many more porcelain fractures occurred on deglazed porcelain. This study indicates that with the appropriate material selection, the silane/composite procedure alone may be adequate for bonding.

Cross-contamination in Porcelain Mortars.

Science.gov (United States)

Bauer-Brandl, A; Falck, A; Ingebrigtsen, L; Nilson, C

2001-01-01

Porcelain mortars and pestles are frequently used to comminute drug substances on a small scale and (in some cases) in the production of liquid and semisolid suspensions. Although it is generally accepted that removal of a drug substance from a rough surface by rinsing may be difficult and may lead to cross-contamination, no hard data support that theory. In this study, the amount of salicylic acid remaining on a porcelain mortar after different washing procedures was quantified and compared with the amount remaining on a plastic mortar. Drug residues in the "mg" range on the porcelain mortars made common rinsing procedures appear inappropriate, but no traces of drug were detected on plastic mortars. In addition, the quality of suspension ointments with respect to particle size and homogeneity produced by the two types of mortars was compared. Porcelain and plastic mortars appeared equally suitable for use in the production of semisolid suspensions.

Main: OPAQUE2ZM22Z [PLACE

Lifescience Database Archive (English)

Full Text Available OPAQUE2ZM22Z S000017 17-May-2001 (last modified) uchi Opaque-2 (O2) target sequence...ene: maize 22-kD zein; transacting factor: 02; O2; opaque; 22-kD zein; seed; ACGT; opaque-2; maize (Zea mays) TCCACGTAGA ...

Toughening of dental porcelain by tetragonal ZrO2 additions

International Nuclear Information System (INIS)

Morena, R.; Lockwood, P.E.; Evans, A.L.; Fairhurst, C.W.

1986-01-01

The effect of mechanical behavior of ZrO 2 additions to a dental porcelain was investigated. The ZrO 2 was introduced into the glassy matrix phase of the porcelain by refritting the all-glass porcelain constituent. X-ray diffraction indicated that a sizeable fraction of the ZrO 2 was retained in the tetragonal from after the porcelain was fired. Zirconia additions to the porcelain produced substantial improvements in fracture toughness, strength, and thermal shock resistance

Neonatal opaque right lung: delayed fluid resorption

International Nuclear Information System (INIS)

Swischuk, L.E.; Hayden, K.; Richardson, J.

1981-01-01

Eight newborn infants with opaque right lungs were examined. Clinically, the main problem associated with the opaque right lung is mild respiratory distress, and radiographyically, the findings consist of (a) a totally opaque right lung, (b) a semiopaque right lung, or (c) an opaque right upper lobe only. These findings are usually interpreted as representing pneumonia, empyema, or hydrochlothorax, but the fact that they clear within 24 to 48 hours indicates that none of these diseases is the cause. It is thought that neonatal opaque right lung results from the transient retention of normal fetal fluid in the right lung

The fingerprint element analysis on provenance of ancient chinese Jun porcelain

International Nuclear Information System (INIS)

Gao Zhengyao; Chen Songhua; Wang Jie; Huang Zhongxiang; Jia Xiuqin; Han Song

1997-01-01

Forty-three samples of ancient Jun porcelains and so on were chosen. Neutron activation analysis (NAA) was used to measure the 36 trace elements in every sample. Seven elements were chosen as the 'fingerprint elements'. The provenance of the glazes and bodies of ancient Chinese Jun porcelain were investigated by the fingerprint element analysis method. The result shows that although the ancient Chinese Jun porcelain samples have been leapt over six hundred years, and glaze colors are utterly different and are from many different kilns, there are long term, stable and same mainly raw material source. The near provenance relation between ancient Jun porcelain and ancient Ru porcelain is preliminarily analyzed. A few modern Jun porcelains approximate from ancient Jun porcelains, the majority become estranged from ancient Jun porcelain

Measurement of annual dose on porcelain using surface TLD method

International Nuclear Information System (INIS)

Xia Junding; Wang Weida; Leung, P.L.

2001-01-01

In order to improve accuracy of TL authentication test for porcelain, a method of measurement of annual dose using ultrathin (CaSO 4 :Tm) dosage layer on porcelain was studied. The TLD was placed on the part of porcelain without glaze. A comparison of measurement of annual dose for surface TLD, inside TLD and alpha counting on porcelain was made. The results show that this technique is suitable for measuring annual dose and improving accuracy of TL authentication test for both porcelain and pottery

[Preliminary evaluation on self-developed dentin porcelain color prediction system].

Science.gov (United States)

Chen, L; Lu, C; Li, X L; Zhu, X M; Zhang, S; Tan, J G

2016-09-01

To apply the self-developed dentin porcelain color prediction system in the fabrication of porcelain-fused-to-metal-crown(PFMC), and to evaluate its accuracy in color-matching. Twenty upper central incisors were recruited according to preset criteria, and three PFMC were made for each tooth using three shade-matching techniques. Group A: PFMC were made according to the result of visual color selection; Group B: an spectrophotometer-based color-matching technique was used; Group C: PFMC were fabricated with dentin porcelain powder calculated by the prediction system according to the L(*), a(*), b(*) value measured by a spectrophotometer. Color differences(ΔE) (measured by spectrophotometer) of three groups of crowns were calculated in the cervical, middle, and incisal regions. The results were analyzed using one-way ANOVA. Mean color differences in body regions were: Group A: 3.53±1.80, Group B: 2.86±1.63, Group C: 3.77±1.40(P>0.05), and those in incisal regions were: Group A: 2.70 ± 1.13, Group B: 2.80 ± 0.90, Group C: 3.04 ± 1.03(P>0.05). In cervical region, Group C had greater color difference than Group B(2.78±1.14)(P0.05). PFMC fabricated using self-developed dentin porcelain color prediction system had similar color matching compared with conventional and instrument-based methods.

INAA analysis for Jun porcelaim and modern Chinese Jun porcelain

International Nuclear Information System (INIS)

Jia Xiuqin; Dong Jinquan; Han Song; Tang Yunhui

2004-01-01

A total of 28 old Jun porcelain, seven modern Chinese Jun porcelain and two Jingdezhen porcelain samples are analyzed with INAA method. The systematic geochemical study for these 37 samples on their REE and trace elements shows that these three types of china were made with relatively stable and similar material, although they leaptover 600 years in different colors and from different kilns. However, the REE patterns of modern Chinese Jun porcelain are a little bit different from that of old Jun porcelain, and clear different from the old glaze of Jindezheng. (authors)

Originating relation studies on ancient porcelains of chines Ru and Jun by NAA

International Nuclear Information System (INIS)

Zhao Weijuan; Xie Jianzhong; Gao Zhengyao; Li Guoxia; Li Rongwu; Zhang Bin

2002-01-01

50 samples of glazes and bodies of the ancient Chinese Ru porcelain, Jun porcelain and imitative ancient ceramics were analyzed by neutron activation analysis (NAA). The contents of 36 elements in each sample were measured. The NAA data were statistically treated by fuzzy cluster method and the trend cluster diagram was obtained. Their classes and raw material sources were determined. The results show that although these samples spanned hundreds of years, came from different kilns and had different glazes colors, the bodies of the ancient Chinese Ru porcelain and Jun porcelain belong to the same kind, the glazes of the ancient Chinese Ru porcelain is similar to the glazes of the ancient Chinese Jun porcelain. The originating places of the body raw material were concentrated, and that of the glaze raw materials were scattered, the source of the glaze raw material covered that the body raw material. The ancient Chinese Ru porcelain and Jun porcelain have basically the same raw material sources and the sources of raw material are stable in long time. It is found that most modern Jun porcelain samples are similar to the ancient Chinese Jun porcelain. Two modern Ru porcelain samples are similar to the ancient Chinese Ru porcelain, but another one drifts apart from the ancient Chinese Ru porcelain. Jingdezhen porcelain has no relation to Ru porcelain and Jun porcelain

Fingerprint elements scatter analysis on ancient chinese Ru porcelains samples

International Nuclear Information System (INIS)

Gao Zhengyao; Wang Jie; Chen Xiande

1997-01-01

Altogether 28 samples, mainly including glazes and bodies of ancient Chinese Ru porcelain, were analyzed by NAA technique and the contents of 36 elements were compared. The scatter analysis for nine fingerprint-elements indicates that almost all ancient Chinese Ru porcelain samples had nearly identical and long-term stable source of raw materials although they were fired in different kilns, at varying time and with distinct colors, and moreover, the source of raw materials for modern Ru porcelain seems to approach that for ancient one. The close provenance relation between ancient Jun porcelain and ancient Ru porcelain is also preliminarily verified. The glaze material of Jingdezhen white porcelain is totally different from all other samples. It shows that the former came from a separate source

The Porcelain Crab Transcriptome and PCAD, the Porcelain Crab Microarray and Sequence Database

Energy Technology Data Exchange (ETDEWEB)

Tagmount, Abderrahmane; Wang, Mei; Lindquist, Erika; Tanaka, Yoshihiro; Teranishi, Kristen S.; Sunagawa, Shinichi; Wong, Mike; Stillman, Jonathon H.

2010-01-27

Background: With the emergence of a completed genome sequence of the freshwater crustacean Daphnia pulex, construction of genomic-scale sequence databases for additional crustacean sequences are important for comparative genomics and annotation. Porcelain crabs, genus Petrolisthes, have been powerful crustacean models for environmental and evolutionary physiology with respect to thermal adaptation and understanding responses of marine organisms to climate change. Here, we present a large-scale EST sequencing and cDNA microarray database project for the porcelain crab Petrolisthes cinctipes. Methodology/Principal Findings: A set of ~;;30K unique sequences (UniSeqs) representing ~;;19K clusters were generated from ~;;98K high quality ESTs from a set of tissue specific non-normalized and mixed-tissue normalized cDNA libraries from the porcelain crab Petrolisthes cinctipes. Homology for each UniSeq was assessed using BLAST, InterProScan, GO and KEGG database searches. Approximately 66percent of the UniSeqs had homology in at least one of the databases. All EST and UniSeq sequences along with annotation results and coordinated cDNA microarray datasets have been made publicly accessible at the Porcelain Crab Array Database (PCAD), a feature-enriched version of the Stanford and Longhorn Array Databases.Conclusions/Significance: The EST project presented here represents the third largest sequencing effort for any crustacean, and the largest effort for any crab species. Our assembly and clustering results suggest that our porcelain crab EST data set is equally diverse to the much larger EST set generated in the Daphnia pulex genome sequencing project, and thus will be an important resource to the Daphnia research community. Our homology results support the pancrustacea hypothesis and suggest that Malacostraca may be ancestral to Branchiopoda and Hexapoda. Our results also suggest that our cDNA microarrays cover as much of the transcriptome as can reasonably be captured in

[Preliminary analysis about influence of porcelain thickness on interfacial crack of PFM].

Science.gov (United States)

Zhu, Ziyuan; Zhang, Baowei; Zhang, Xiuyin; Xu, Kan; Fang, Ruhua; Wang, Dongmei

2002-01-01

This study was about the influence of porcelain thickness on crack at interface. The effect of porcelain thickness on the flaw at the interface between porcelain and metal was studied in three groups with porcelain thickness of 0.5 mm, 1.5 mm and 2.5 mm (metal thickness of 0.5 mm) by means of moire interferometre and interfacial fracture mechanics. The parameter Jc was compared among the three groups and the growing of the flaw was observed. Jc and the extreme strength of group with porcelain thickness of 0.5 mm (2.813 N/m and 9.979 N) were lower than those of the groups with porcelain thickness of 1.5 mm and 2.5 mm (5.395 N/m, 19.134 N and 5.429 N/m, 19.256 N). Flaws extend along the interface in the groups with porcelain thickness of 1.5 mm and 0.5 mm. (1) Fracture resistance of the interface in the groups with porcelain thickness of 1.5 mm and 2.5 mm is similar and it decreases in the group with 0.5 mm thick porcelain. (2) When porcelain is 1.5 mm or 0.5 mm thick, flaws will extend along the interface. When porcelain is 2.5 mm thick, flaws will extend into the porcelain layer.

Principal Component Analysis of Chinese Porcelains from the Five Dynasties to the Qing Dynasty

Science.gov (United States)

Yap, C. T.; Hua, Younan

1992-10-01

This is a study of the possibility of identifying antique Chinese porcelains according to the period or dynasty, using major and minor chemical components (SiO2 , Al2O3 , Fe2O3 , K2O, Na2O, CaO and MgO) from the body of the porcelain. Principal component analysis is applied to published data on 66 pieces of Chinese procelains made in Jingdezhen during the Five Dynasties and the Song, Yuan, Ming and Qing Dynasties. It is shown that porcelains made during the Five Dynasties and the Yuan (or Ming) and Qing Dynasties can be segregated completely without any overlap. However, there is appreciable overlap between the Five Dynasties and the Song Dynasty, some overlap between the Song and Ming Dynasties and also between the Yuan and Ming Dynasties. Interestingly, Qing procelains are well separated from all the others. The percentage of silica in the porcelain body decreases and that of alumina increases with recentness with the exception of the Yuan and Ming Dynasties, where this trend is reversed.

Line scan analysis of the component of Ru porcelain by SRXRF method

International Nuclear Information System (INIS)

Zhu Jian; Mao Zhenwei; Yang Yimin; Feng Min; Wang Changsui; Sun Xinmin; Guo Musen; Huang Yuying; He Wei

2002-01-01

The technique of the SRXRF line scan analysis was used to measure contents of 11 elements at the broken plane of the Ru porcelain from porcelain glaze to body. It is found that there exists a great different layer of contents of elements between the porcelain glaze and body. The mechanism may be that in the process of firing the porcelain, materials of glass-glaze of porcelain glaze infiltrate into the surface of porcelain body, that could fit the phenomenon of observation by different microscopes (stereomicroscope, polarizing microscope and scanning electron microscope)

[Adhesion of oral microorganisms on dental porcelain polished and glazed].

Science.gov (United States)

Wang, Yi-ning; Wen, Guo-jiang; Shi, Bin; Pan, Xin-hua

2003-09-01

This study compared the roughness of porcelain polished or glazed surfaces and the adhesion of oral streptococcus mutans to them in vitro. 30 porcelain samples were made. Porcelain samples in group A were polished with diamond paste. Porcelain samples were glazed in group B and were polished with Al2O3 (240#) bur in group C. Their roughness values were measured by profilometer. Standardized cell suspensions were incubated with test samples for one hour at 37 degrees C, then retained cells were counted by image analysis (percentage area of a microscopic field covered by cells). Roughness values of group A, B, C were respectively (0.1987 +/- 0.057) microm, (0.1990 +/- 0.091) microm, (0.4260 +/- 0.174) microm. There was no significantly difference between group A and group B. The roughness samples in group C were significantly rougher than that in the other groups. The amount of retained cells in group A, group B, group C was respectively (15.92 +/- 4.37)%, (16.39 +/- 6.31)% and (41.48 +/- 12.1)%. There was no significant difference between the cell adhesion on porcelain surface glazed and polished, but more bacteria adhered on the porcelain surface in group C. Porcelain surface polished treatment was clinically acceptable compared with its glazed. They all exhibited the least amount of bacteria adhesion. The more porcelain surface was rough, the more bacteria adhered on it.

Neutron activation analysis of some ancient and modern Chinese Jun Porcelain samples

International Nuclear Information System (INIS)

Gao Zhengyao; Wang Jie; Chen Songhua; Huang Zhongxiang; Han Song; Jia Xiuqin

1997-01-01

Up to 43 glaze and body samples of ancient and modern Chinese Jun Porcelain and other porcelain are chosen and contents of 36 elements for each sample are determined by NAA. The NAA data are then analysed by the fuzzy cluster method. The result shows that although the ancient Jun Porcelain samples span leaped 600 years and are from different kilns and their glaze colors are utterly different, they have a long-term, stable and mainly the same supply of raw material. The relation between ancient Jun Porcelain and ancient Ru Porcelain is also preliminarily analysed. It is found that only few modern Jun Porcelain samples are similar to ancient Jun Porcelain but the majority of them are different from ancient ones

Influence of surface treatments on the shear bond strength of orthodontic brackets to porcelain

Science.gov (United States)

Wang, Cong; Zeng, Jishan; Wang, Shaoan; Yang, Zheng; Huang, Qian; Chen, Pixiu; Zhou, Shujuan; Liu, Xiaoqing

2008-11-01

The purpose of this study was to investigate the effect of various surface treatments after different storage time and thermocycling on the shear bond strength of orthodontic brackets to the feldspathic porcelain surfaces. 128 disc-shaped porcelain specimens were randomly assigned to the following surface treatments: 9.6% HFA, 9.6% HFA combined with silane, 50 μ aluminum trioxide sandblasting followed by silane and application of silane after 37% phosphoric acid. Metal or ceramic brackets were bonded onto each treated porcelain facet with light cured resin. The samples were stored in 37 °C water 1 day or 7 days, thermocycled 500 times from 5 to 55 °C. The shear bond strengths were measured (1 mm/min), and statistically analyzed. The bond failure sites were classified according to ARI system. The surface of the glazed, sandblasted, hydrofluoric and phosphoric acid etched porcelain were examined with SEM. All groups achieved reasonable bond strengths to withstand the application of orthodontic forces. Water storage for 7 days caused lower shear bond strength than that of 1 day. But there is no statistically significant difference between the two groups. The mean shear bond strength provided by ceramic bracket with mechanical retention had no statistical difference with that of metal bracket. Therefore, the optimal treatment for orthodontic brackets bonding to feldspathic porcelain was to apply phosphoric acid combined with silane.

Dating ancient Chinese celadon porcelain by neutron activation analysis and bayesian classification

International Nuclear Information System (INIS)

Xie Guoxi; Feng Songlin; Feng Xiangqian; Zhu Jihao; Yan Lingtong; Li Li

2009-01-01

Dating ancient Chinese porcelain is one of the most important and difficult problems in porcelain archaeological field. Eighteen elements in bodies of ancient celadon porcelains fired in Southern Song to Yuan period (AD 1127-1368) and Ming dynasty (AD 1368-1644), including La, Sm, U, Ce, etc., were determined by neutron activation analysis (NAA). After the outliers of experimental data were excluded and multivariate normal distribution was tested, and Bayesian classification was used for dating of 165 ancient celadon porcelain samples. The results show that 98.2% of total ancient celadon porcelain samples are classified correctly. It means that NAA and Bayesian classification are very useful for dating ancient porcelain. (authors)

PIXE analysis of Chinese ancient greenish white porcelain

International Nuclear Information System (INIS)

Cheng Lin; Ding Xunliang; Feng Songlin; Cheng Huangsheng; Zhang WenJiang; Fan Changsheng

2006-01-01

This paper reports the results about the PIXE analysis of major, minor and trace elements of Chinese ancient greenish white porcelain and blue-and-white porcelain produced in Hutian Kiln (Jingdezhen district, Jiangxi province) during 10th-14th centuries. The porcelain body and greenish white glaze from northern Song (AD 960), southern Song (AD 1037-1276), early Yuan (AD 1279-1320), later Yuan (AD 1320-1368) were investigated together with white-and-blue glaze from Ming dynasty (AD 1368-1644). The obtained data were further analyzed by factor analysis

PIXE analysis of Chinese ancient greenish white porcelain

Energy Technology Data Exchange (ETDEWEB)

Cheng Lin [Institute of Low Energy Nuclear Physics, Beijing Normal University, Beijing 100875 (China)]. E-mail: chenglinbnu@hotmail.com; Ding Xunliang [Institute of Low Energy Nuclear Physics, Beijing Normal University, Beijing 100875 (China); Feng Songlin [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); Cheng Huangsheng [Institute of Modern Physics, Fudan University, Shanghai 200433 (China); Zhang WenJiang [Jiangxi Provincial Institute of Cultural Relics and Archaeology, Nanchang 330008 (China); Fan Changsheng [Jiangxi Provincial Institute of Cultural Relics and Archaeology, Nanchang 330008 (China)

2006-03-15

This paper reports the results about the PIXE analysis of major, minor and trace elements of Chinese ancient greenish white porcelain and blue-and-white porcelain produced in Hutian Kiln (Jingdezhen district, Jiangxi province) during 10th-14th centuries. The porcelain body and greenish white glaze from northern Song (AD 960), southern Song (AD 1037-1276), early Yuan (AD 1279-1320), later Yuan (AD 1320-1368) were investigated together with white-and-blue glaze from Ming dynasty (AD 1368-1644). The obtained data were further analyzed by factor analysis.

PIXE analysis of Chinese ancient greenish white porcelain

Science.gov (United States)

Cheng, Lin; Ding, Xun-liang; Feng, Song-lin; Cheng, Huang-sheng; Zhang, Wen-Jiang; Fan, Chang-Sheng

2006-03-01

This paper reports the results about the PIXE analysis of major, minor and trace elements of Chinese ancient greenish white porcelain and blue-and-white porcelain produced in Hutian Kiln (Jingdezhen district, Jiangxi province) during 10th-14th centuries. The porcelain body and greenish white glaze from northern Song (AD 960), southern Song (AD 1037-1276), early Yuan (AD 1279-1320), later Yuan (AD 1320-1368) were investigated together with white-and-blue glaze from Ming dynasty (AD 1368-1644). The obtained data were further analyzed by factor analysis.

4-META opaque resin--a new resin strongly adhesive to nickel-chromium alloy.

Science.gov (United States)

Tanaka, T; Nagata, K; Takeyama, M; Atsuta, M; Nakabayashi, N; Masuhara, E

1981-09-01

1) A new adhesive opaque resin containing a reactive monomer, 4-methacryloxy-ethyl trimellitate anhydride (4-META), was prepared, and its application to thermosetting acrylic resin veneer crowns was studied. 2) The 4-META opaque resin was applied to a variety of nickel-chromium dental alloy specimens which had undergone different treatment, and endurance tests were conducted to evaluate the durability of adhesion. 3) Stable adhesion against water penetration was achieved with metal surfaces first etched with HCl and then oxidized with HNO3. A bond strength of 250 kg/cm2 was maintained even after immersion in water at 37 degrees C for 30 wk or at 80 degrees C for ten wk. Furthermore, this value did not decrease even after the specimens were subjected to 500 thermal cycles. 4) The 4-META opaque resin studied can eliminate the necessity for retention devices on metal castings. 5) The smooth 4-META opaque resin should have no adverse effects on gingivae.

Selling Tourism Products through the Opaque Channels

OpenAIRE

Ogonowska, Malgorzata

2012-01-01

International audience; This paper analyses the properties of the advanced Opaque booking systems used by online travel agencies in conjunction with their traditional transparent booking system. In section 2 an updated literature review is presented. This review underlines the interest and the specificities of Opaque goods in the Tourism Industry. It also characterises properties of the Name-Your-Own-Price channel introduced by Priceline and the Opaque channel developed by Hotwire. Then, in s...

[Effect of sintering gold paste coating on the bonding strength of pure titanium and three low-fusing porcelains].

Science.gov (United States)

Zhang, Ya-li; Luo, Xiao-ping; Zhou, Li

2012-05-01

To study the effect of sintering gold paste coating of pure titanium on the adhesion of three porcelains following the protocol ISO 9693, and to investigate the titanium-porcelains interfaces. Sixty machined pure titanium samples were prepared in a rectangular shape according to ISO 9693 and divided equally into six groups. Half of the strips were coated with gold paste (Deckgold) and sintered. Three ultra-low-fusing dental porcelains (I: Initial Ti, S: Super porcelain Ti-22, T: TitanKeramik) were fused onto the titanium surfaces. A thin layer of bonding agent was only applied on the surfaces of uncoated gold specimens. The interface of the porcelain and titanium was observed with a field emission scanning electron microscope (FE-SEM) after metallographic preparation and sputtered with a very thin carbon layer of the embedded titanium-porcelain interface. After three-point bending test was performed, optical stereomicroscope was used to characterize the titanium-porcelains adhesion and determine the mode of failure. FE-SEM illustrated intermetallic compounds of Au-Ti formed with some visible microcracks in the gold layer and the interface of gold layer and ceramic. All the uncoated gold titanium-porcelain system showed predominately adhesive fracture at the titanium oxidation, whereas the failure modes in all gold coated systems were cohesive and adhesive, mainly cohesive. The three-point-bending test showed that the bonding strength of GS and GI groups [(37.08 ± 4.32) and (36.20 ± 2.40) MPa] were higher than those in uncoated groups [(31.56 ± 3.74) and (30.88 ± 2.60) MPa, P 0.05). The gold paste intermediate coatings can improve bond strengths of Super porcelain Ti-22 system and Initial Ti system, which have potential applications in clinical fields.

PIXE analysis of ancient Chinese Qing dynasty porcelain

Science.gov (United States)

Cheng, Huansheng; He, Wenquan; Tang, Jiayong; Yang, Fujia; Wang, Jianhua

1996-09-01

The major and minor chemical compositions and trace element content of white glaze made in Qing dynasty at kuan kiln have been determined by PIXE. Experimental results show that trace element contents RbSrZr are useful to distinguish the place of production of ancient porcelain. In the porcelain from different kilns situated in a same province, the trace element contents can be different from each other. Determining and comparing the major and minor compositions and trace elemental concentrations in white glaze by PIXE technique, we can distinguish a precious Qing dynasty porcelain made at kuan kiln from a fake.

Incorporation of tv tube glass waste in aluminous porcelain

Energy Technology Data Exchange (ETDEWEB)

Holanda, J.N.F.; Santos, T.F.; Paes Junior, H.R. [Universidade Estadual do Norte Fluminense (UENF), Campos dos Goytacazes, RJ (Brazil)

2016-07-01

Full test: This work analyzes the reuse of TV tube glass waste as a method to provide alternative raw material for aluminous porcelain, through of replacement of natural sodic feldspar by up to 30 wt.%. Aluminous porcelain formulations containing TV tube glass waste were pressed and fired in air at 1300 deg C using a fast-firing cycle. Ceramic pieces were characterized by X-ray diffraction, scanning electron microscopy, linear shrinkage, apparent density, apparent porosity, water absorption, and electrical resistivity. XRD and SEM results indicated that all aluminous porcelain pieces are composed essentially of mullite, quartz, and ?-alumina embedded in a vitreous matrix. The results also showed that the aluminous porcelain pieces containing TV tube glass waste presented low water absorption values between 0.42 and 0.45 %, apparent density between 2.44 and 2.46 g/cm3, and volume electrical resistivity between 1.91 and 2.93 x 1011 ?.cm. Thus, the TV tube glass waste could be used into aluminous porcelain formulations, in the range up to 30 wt.%, as a replacement for traditional flux material (sodic feldspar). (author)

Effects of metal surface grinding at the porcelain try-in stage of fixed dental prostheses.

Science.gov (United States)

Kılınç, Halil İbrahim; Kesim, Bülent; Gümüş, Hasan Önder; Dinçel, Mehmet; Erkaya, Selçuk

2014-08-01

This study was to evaluate the effect of grinding of the inner metal surface during the porcelain try-in stage on metal-porcelain bonding considering the maximum temperature and the vibration of samples. Ninety-one square prism-shaped (1 × 1 × 1.5 mm) nickel-chrome cast frameworks 0.3 mm thick were prepared. Porcelain was applied on two opposite outer axial surfaces of the frameworks. The grinding was performed from the opposite axial sides of the inner metal surfaces with a low-speed handpiece with two types of burs (diamond, tungsten-carbide) under three grinding forces (3.5 N, 7 N, 14 N) and at two durations (5 seconds, 10 seconds). The shear bond strength (SBS) test was performed with universal testing machine. Statistical analyzes were performed at 5% significance level. The samples subjected to grinding under 3.5 N showed higher SBS values than those exposed to grinding under 7 N and 14 N (P.05). The types of bur (P=.965) and the duration (P=.679) did not affect the SBS values. On the other hand, type of bur, force applied, and duration of the grinding affected the maximum temperatures of the samples, whereas the maximum vibration was affected only by the type of bur (PGrinding the inner metal surface did not affect the metal-porcelain bond strength. Although the grinding affected the maximum temperature and the vibration values of the samples, these did not influence the bonding strength.

Temperature changes across porcelain during multiple exposure CO2 lasing

Science.gov (United States)

Barron, Joseph R.; Zakariasen, Kenneth L.; Peacocke, Larry

1990-06-01

Research indicates that laser energy may provide a useful method for glazing and fusing porcelain for intraoral prosthetic purposes. However, it is not known whether such lasing will result in the production of heat levels that may be damaging to adjacent vital tissues such as the dental pulp and periodontal tissues. This research is designed to measure the magnitude of temperature rise across porcelain observed during multiple exposure C02 lasing. Fifteen porcelain examples of 1000 jim (5), 1500 pm (5) and 2000 tm (5) x each received five C02 laser exposures on the same exposure site at 1.0 sec. intervals at 8.0 watts (0.2 sec. per exposure with a 1 mm focal spot). A YSI 144201 thermilinear precision thermistor was placed on the porcelain surface opposite each laser exposure site. Temperature rise above ambient was recorded by an HP3421A data acquisition unit and HP9816 technical microcomputer. Recording continued for sufficient time to allow temperatures to return to ambient. The mean temperature elevations ranged from a low of 2.97 0C (2000 pm) to a high of 7.77 °C (1000 μm). ANOVA and Duncan's Multiple Range Test indicated significant differences in temperature rise by porcelain thickness. It would appear from the results of this research that temperature elevations adjacent to lased porcelain may be sufficiently controllable that safe intraoral porcelain lasing will be possible.

Non-destructive analysis and appraisal of ancient Chinese porcelain by PIXE

International Nuclear Information System (INIS)

Cheng, H.S.; Zhang, Z.Q.; Xia, H.N.; Jiang, J.C.; Yang, F.J.

2002-01-01

This paper reports the results of the PIXE analysis on ancient Chinese blue and white porcelain fired at Kuan Kiln (Jingdezhen, Jiangxi province) during 13-19th century. The major, minor and trace element of porcelain body, white glaze and blue glaze were determined by PIXE. In this paper the chemical compositions of porcelain body, white glaze and blue glaze measured from Yuan (AD 1206-1368), Ming (AD 1368-1644) and Qing (AD 1616-1911) blue and white porcelain are present. The cobalt blue pigment used in Yuan, Ming and Qing are also discussed

EDXRF analysis of Yanhedian Ru kiln and Jun official kiln porcelain

International Nuclear Information System (INIS)

Wen Chang; Zhao Huixian; Li Guoxia; Gao Zhengyao; Zhao Weijuan; Sun Hongwei; Guo Min; Xie Jianzhong; Li Rongwu; Guo Peiyu

2009-01-01

The chemical components of the body and glaze samples of some Ru porcelains from Yanhedian kiln and Jun official porcelains from Juntai kiln are determined by the technology of Energy Dispersive X-ray Fluorescence(EDXRF) in this work. The difference of the two kiln's glaze and body are analyzed by factor analysis method of Multi-dimensional statistical analysis. The results indicate that Yanhedian Ru porcelains can be well distinguished from Jun official porcelains from Juntai kiln. This evidence once again proves that Jun ceramics and Ru ceramics can be distinguished obviously. (authors)

Non-destructive analysis and appraisal of ancient Chinese porcelain by PIXE

Science.gov (United States)

Cheng, H. S.; Zhang, Z. Q.; Xia, H. N.; Jiang, J. C.; Yang, F. J.

2002-05-01

This paper reports the results of the PIXE analysis on ancient Chinese blue and white porcelain fired at Kuan Kiln (Jingdezhen, Jiangxi province) during 13-19th century. The major, minor and trace element of porcelain body, white glaze and blue glaze were determined by PIXE. In this paper the chemical compositions of porcelain body, white glaze and blue glaze measured from Yuan (AD 1206-1368), Ming (AD 1368-1644) and Qing (AD 1616-1911) blue and white porcelain are present. The cobalt blue pigment used in Yuan, Ming and Qing are also discussed.

Radio-opaque dental compositions

International Nuclear Information System (INIS)

Temin, S.C.

1979-01-01

Thorium oxide or tantalum oxide, or combinations thereof are used as the x-ray material for radio-opaque filler compositions having particular applicability in dental restorative compositions. The filler compositions contain from about 3% by weight to about 10% by weight, based on the total filler composition, of the x-ray absorbing materials and the remainder being conventional particulate glass or silica, quarts or ceramic filler material. The radio opaque filler compositions are insoluble and non-leachable in alkaline, acidic or neutral aqueous environments, are essentially non-toxic, are either essentially colorless or translucent, and are compatible with acrylic monomers and other polymerizable binder systems

Study and rheological characterization of various bone ash porcelain formulations

International Nuclear Information System (INIS)

Carus, L.A.; Bento, L.; Braganca, S.R.

2012-01-01

The bone ash porcelain is a widely accepted product on the market because their qualities such as high strength and whiteness, to differ from common table porcelains. Its traditional formulation comes from an English recipe, consisting of 25% of kaolin, 25% of feldspar and 50% of bovine bone ash. In some studies, this proportion is adapted to regional conditions, optimizing the formulation according to the raw materials available. In this study, the rheological behavior of bone porcelain suspensions, in which the flux feldspar is partially substituted by an alternative flux (espudomenio, wollastonite and glass). The results show that the rheological behavior of porcelain is affected by the size, shape, surface area and particle size distribution of particles in suspension

Valorization of rice straw waste: production of porcelain tiles

Directory of Open Access Journals (Sweden)

Álvaro Guzmán A

2015-12-01

Full Text Available Abstract The rice industry generates huge amounts of rice straw ashes (RSA. This paper presents the results of an experimental research work about the incorporation of RSA waste as a new alternative raw material for production of porcelain tiles. The RSA replaces, partially or completely, the non-plastic raw materials (quartz (feldspathic sand in this research and feldspar, that together with the clays, constitute the major constituents of formulations of porcelain tiles. A standard industrial composition (0% RSA and two more compositions in which feldspar and feldspathic sand were replaced with two percentages of RSA (12.5% RSA and 60% RSA were formulated, keeping the clay content constant. The mixtures were processed, reproducing industrial porcelain tile manufacturing conditions by the dry route and fired at peak temperatures varying from 1140-1260 ºC. The results showed that additions of 12.5% RSA in replacement of feldspar and feldspathic sand allowed producing porcelain tiles that did not display marked changes in processing behaviour, in addition to obtain a microstructure and the typical mineralogical phases of porcelain tile. Thus, an alternative use of an agricultural waste material is proposed, which can be translated into economic and environmental benefits.

Locating the origins of blue and white porcelains using EDXRF

International Nuclear Information System (INIS)

Yu, K.N.; Miao, J.M.

1997-01-01

Among the main sites of production of ancient Chinese blue and white porcelains can be included Jingdezhen in Jiangxi Province, the Yuxi and Jianshui Kilns of Yunnan Province and the Pinghe Kiln of Fujian Province. The current work focuses on an elemental characterization of ancient porcelains according to the location of manufacture, also incorporating a similar study of the blue and white porcelains of the Qing dynasty from Wun Yiu in Hong Kong, and modern blue and white porcelains from Germany, Japan and Thailand. Non-destructive analysis of samples of porcelain using energy dispersive X-ray fluorescence (EDXRF) has yielded results in terms of 13 chemical elements, namely, Ti, Mn, Fe, Co, Ni, Cu, Zn, Ga, Pb, Rb, Sr, Y and Zr. Principal component analysis has been performed on the data, allowing representation of the first, second and third principal components of the data in 3 D scatter plots; the results reveal data clusterings which correlate to a high degree with the known sites of origin. The conclusion is that the present method is capable of determining differences in elemental concentrations of blue and white porcelains, and that these differences can be used to locate the originating site of manufacture. (Author)

Locating the origins of blue and white porcelains using EDXRF

Energy Technology Data Exchange (ETDEWEB)

Yu, K.N. [City Univ., Hong Kong (Hong Kong). Dept. of Physics and Materials Science; Miao, J.M. [Palace Museum, Beijing (China). Dept. of Science and Technology

1997-07-30

Among the main sites of production of ancient Chinese blue and white porcelains can be included Jingdezhen in Jiangxi Province, the Yuxi and Jianshui Kilns of Yunnan Province and the Pinghe Kiln of Fujian Province. The current work focuses on an elemental characterization of ancient porcelains according to the location of manufacture, also incorporating a similar study of the blue and white porcelains of the Qing dynasty from Wun Yiu in Hong Kong, and modern blue and white porcelains from Germany, Japan and Thailand. Non-destructive analysis of samples of porcelain using energy dispersive X-ray fluorescence (EDXRF) has yielded results in terms of 13 chemical elements, namely, Ti, Mn, Fe, Co, Ni, Cu, Zn, Ga, Pb, Rb, Sr, Y and Zr. Principal component analysis has been performed on the data, allowing representation of the first, second and third principal components of the data in 3 D scatter plots; the results reveal data clusterings which correlate to a high degree with the known sites of origin. The conclusion is that the present method is capable of determining differences in elemental concentrations of blue and white porcelains, and that these differences can be used to locate the originating site of manufacture. (Author).

The analysis of Chinese porcelains and ceramics

International Nuclear Information System (INIS)

Peisach, M.; Jacobson, L.; Vos, H.N.

1985-01-01

Fragments of Chinese porcelains and ceramics have been excavated in the southern Cape. Because of the cultural history value of the material, analyses were carried out by the non-destructive methods of PIPPS (particle-induced prompt photon spectrometry) and PIXE using the external beam facility at the Faure Van de Graaff accelerator. For comparison a suite of English porcelain from about the same period was analysed as a control

[Preliminary study of bonding strength between diatomite-based dental ceramic and veneering porcelains].

Science.gov (United States)

Lu, Xiao-li; Gao, Mei-qin; Cheng, Yu-ye; Zhang, Fei-min

2015-04-01

In order to choose the best veneering porcelain for diatomite-based dental ceramic substrate, the bonding strength between diatomite-based dental ceramics and veneering porcelains was measured, and the microstructure and elements distribution of interface were analyzed. The coefficient of thermal expansion (CTE) of diatomite-based dental ceramics was detected by dilatometry. Three veneering porcelain materials were selected with the best CTE matching including alumina veneering porcelain (group A), titanium porcelain veneering porcelain (group B), and E-max veneering porcelain (group C). Shear bonding strength was detected. SEM and EDS were used to observe the interface microstructure and element distribution. Statistical analysis was performed using SPSS 17.0 software package. The CTE of diatomite-based dental ceramics at 25-500 degrees centigrade was 8.85×10-6K-1. The diatomite-based substrate ceramics combined best with group C. Shear bonding strength between group A and C and group B and C both showed significant differences(P<0.05). SEM and EDS showed that the interface of group C sintered tightly and elements permeated on both sides of the interface. The diatomite-based substrate ceramics combines better with E-max porcelain veneer.

Investigation on the Tribological Behavior and Wear Mechanism of Five Different Veneering Porcelains.

Directory of Open Access Journals (Sweden)

Jie Min

Full Text Available The primary aim of this research was to investigate the wear behavior and wear mechanism of five different veneering porcelains.Five kinds of veneering porcelains were selected in this research. The surface microhardness of all the samples was measured with a microhardness tester. Wear tests were performed on a ball-on-flat PLINT fretting wear machine, with lubrication of artificial saliva at 37°C. The friction coefficients were recorded by the testing system. The microstructure features, wear volume, and damage morphologies were recorded and analyzed with a confocal laser scanning microscope and a scanning electron microscope. The wear mechanism was then elucidated.The friction coefficients of the five veneering porcelains differ significantly. No significant correlation between hardness and wear volume was found for these veneering porcelains. Under lubrication of artificial saliva, the porcelain with higher leucite crystal content exhibited greater wear resistance. Additionally, leucite crystal size and distribution in glass matrix influenced wear behavior. The wear mechanisms for these porcelains were similar: abrasive wear dominates the early stage, whereas delamination was the main damage mode at the later stage. Furthermore, delamination was more prominent for porcelains with larger crystal sizes.Wear compatibility between porcelain and natural teeth is important for dental restorative materials. Investigation on crystal content, size, and distribution in glass matrix can provide insight for the selection of dental porcelains in clinical settings.

[Effects of laser welding on bond of porcelain fused cast pure titanium].

Science.gov (United States)

Zhu, Juan-fang; He, Hui-ming; Gao, Bo; Wang, Zhong-yi

2006-04-01

To investigate the influence of the laser welding on bond of porcelain fused to cast pure titanium. Twenty cast titanium plates were divided into two groups: laser welded group and control group. The low-fusing porcelain was fused to the laser welded cast pure titanium plates at fusion zone. The bond strength of the porcelain to laser welded cast pure titanium was measured by the three-point bending test. The interface of titanium and porcelain was investigated by scanning electron microscopy (SEM) and energy depressive X-ray detector (EDX). The non-welded titanium plates were used as comparison. No significant difference of the bond strength was found between laser-welded samples [(46.85 +/- 0.76) MPa] and the controls [(41.71 +/- 0.55) MPa] (P > 0.05). The SEM displayed the interface presented similar irregularities with a predominance. The titanium diffused to low-fusing porcelain, while silicon and aluminum diffused to titanium basement. Laser welding does not affect low-fusing porcelain fused to pure titanium.

Study on blue and white porcelain by EDXRF method

International Nuclear Information System (INIS)

Miao Jianmin; Yu, P.K.N.; Li, M.T.W.

1997-01-01

The EDXRF method was used to find the concentration of component elements in blue and white porcelain. It was found that some elements in colorant were diffused towards glaze layer when the porcelain had been fired at high temperature. Through the half-value thickness calculation, the contribution of some elements from the porcelain's body to the measured intensity was also confirmed. The experiment also indicated that the contents of various elements in the glaze layer of non-decorated portions were definite in spite of the measuring sites, while those of some elements in decorated portions were dependent on positions

Human perception of dental porcelain translucency correlated to spectrophotometric measurements.

Science.gov (United States)

Liu, Min-Chieh; Aquilino, Steven A; Lund, Peter S; Vargas, Marcos A; Diaz-Arnold, Ana M; Gratton, David G; Qian, Fang

2010-04-01

This study evaluated the relationship between instrumental measurements and subjective visual assessment of differences in dental porcelain translucency. Unshaded feldspathic porcelain was used with controlled amounts of tin oxide to create two groups of 12-mm diameter disks with incremental changes in opacity. Contrast ratio (CR = Yb/Yw) was determined with a spectrophotometer, and used as a measure of porcelain translucency (Group A = 0.20 to 0.40; Group B = 0.6-0.8). Within each group, there were 14 specimens with 11 CRs. Three observer groups (first year dental students, residents, faculty with >10 years of shade matching experience) were recruited to assess the translucency between porcelain disks under two lighting conditions (reflected light, transmitted light). Each subject's ability to distinguish between specimens of differing translucency was determined. Descriptive statistics and three-way ANOVA followed by a post-hoc Tukey-Kramer test were used to evaluate the translucency perception threshold (TPT) of subjects (alpha= 0.05). The overall mean TPT (DeltaC) was 0.07, while 50% of the subjects could perceive a 0.06 CR difference between porcelain specimens. Three-way ANOVA revealed a significant difference in translucency perception among the observer groups (p or =10 years) significantly improved the ability to perceive differences in translucency; however, neither the viewing condition nor porcelain opacity affected the perceived translucency threshold.

Direct measurement of annual β dose using TLD on porcelain

International Nuclear Information System (INIS)

Leung, P.L.; Stokes, M.J.; Xia Junding; Wang Weida; Zhou Zhixin

1999-01-01

In order to improve accuracy of TL authentication test for porcelain, a method of direct measurement of annual β dose using ultrathin TLD (CaSO 4 :Tm) on porcelain was studied. Since the TLD was placed into a hole left after sampling for the TL measurement, the method will not cause any new damage to the studied object. The results show that the technique is suitable for measuring annual β dose and improving accuracy of TL authentication test for both porcelain and pottery

Viscoelastic finite element analysis of residual stresses in porcelain-veneered zirconia dental crowns.

Science.gov (United States)

Kim, Jeongho; Dhital, Sukirti; Zhivago, Paul; Kaizer, Marina R; Zhang, Yu

2018-06-01

The main problem of porcelain-veneered zirconia (PVZ) dental restorations is chipping and delamination of veneering porcelain owing to the development of deleterious residual stresses during the cooling phase of veneer firing. The aim of this study is to elucidate the effects of cooling rate, thermal contraction coefficient and elastic modulus on residual stresses developed in PVZ dental crowns using viscoelastic finite element methods (VFEM). A three-dimensional VFEM model has been developed to predict residual stresses in PVZ structures using ABAQUS finite element software and user subroutines. First, the newly established model was validated with experimentally measured residual stress profiles using Vickers indentation on flat PVZ specimens. An excellent agreement between the model prediction and experimental data was found. Then, the model was used to predict residual stresses in more complex anatomically-correct crown systems. Two PVZ crown systems with different thermal contraction coefficients and porcelain moduli were studied: VM9/Y-TZP and LAVA/Y-TZP. A sequential dual-step finite element analysis was performed: heat transfer analysis and viscoelastic stress analysis. Controlled and bench convection cooling rates were simulated by applying different convective heat transfer coefficients 1.7E-5 W/mm 2 °C (controlled cooling) and 0.6E-4 W/mm 2 °C (bench cooling) on the crown surfaces exposed to the air. Rigorous viscoelastic finite element analysis revealed that controlled cooling results in lower maximum stresses in both veneer and core layers for the two PVZ systems relative to bench cooling. Better compatibility of thermal contraction coefficients between porcelain and zirconia and a lower porcelain modulus reduce residual stresses in both layers. Copyright © 2018 Elsevier Ltd. All rights reserved.

Comparative Evaluation of Effects of Laser Modalities on Shear Bond Strengths of Veneering Porcelains to Laser Sintered Substructures: An In Vitro Study.

Science.gov (United States)

Gorler, Oguzhan; Saygin, Aysegul Goze

2017-06-01

Laser modalities and direct metal laser sintering (DMLS) have a potential to enhance micromechanical bonding between dental super- and infrastructures. However, the effect of different manufacturing methods on the metal-ceramic bond strength needs further evaluation. We investigated the effect of surface treatment with Er:YAG, Nd:YAG, and Ho:YAG lasers on the shear bond strength (SBS) of high-fusion dental porcelains (Vita and G-Ceram) to infrastructures prepared with DMLS in vitro settings. Study specimens (n = 128) were randomly divided into study subsets (n = 8), considering treatment types applied on the surface of infrastructures, including sandblasting and selected laser modalities; infrastructure types as direct laser sintered (DLS) and Ni-Cr based; and superstructure porcelains as Vita and G-Ceram. The SBS test was performed to assess the effectiveness of surface modifications that were also examined with a stereo microscope. Considering laser procedure types, the highest SBS values were obtained by Er:YAG laser, followed by, with a decreasing efficiency, Ho:YAG laser and sandblasting procedures, and Nd:YAG laser procedure (p laser decreases the bonding of Vita and G-Ceram in all the infrastructures compared with sandblasting. Considering porcelains, the highest SBS values were obtained by Vita (p laser procedures caused surface irregularities as revealed by the stereo microscopic examination. In current experimental settings, Er:YAG laser applied to DLS infrastructure veneered with Vita porcelain increases bonding strength more distinctly, and Nd:YAG laser applied to Ni-Cr-based infrastructure veneered with G-Ceram porcelain alters bonding strength unfavorably.

Opaque Selling: Static or Inter-Temporal Price Discrimination?

OpenAIRE

Courty, Pascal; Liu, Wenyu

2013-01-01

We study opaque selling in the hotel industry using data from Hotwire.com. An opaque room discloses only the star level and general location of the hotel at the time of booking. The exact identity of the hotel is disclosed after the booking is completed. Opaque rooms sell at a discount of 40 percent relative to regular rooms. The discount increases when hotels are more differentiated. This finding is consistent with static models of price discrimination. No support was found for predictions s...

Chemical and isotopic fingerprinting of ancient Chinese porcelains

International Nuclear Information System (INIS)

Zhao, J.-X.; Li, B.-P.; Greig, A.; Collerson, K.D.; Feng, Y.-X.

2005-01-01

We have obtained unequivocal fingerprinting for many Chinese porcelains of utmost significance, based on high-precision multi-element and isotopic analysis by inductively-coupled mass spectrometry (ICP-MS) and thermal ionization mass spectrometry (TIMS) in our laboratory. As most ancient Chinese kilns used raw materials mined from local areas, differences in the geochemistry and mineralogy of these raw materials are expected to be preserved as distinctive geochemical and isotopic signatures in finished products and this may be useful for identifying their sources. Production techniques, such as purifying and mixing of different raw materials, may also vary from kiln to kiln, or may even change over time. All of that could also potentially leave a characteristic chemical and isotopic signature in a kiln's finished products. Using a tiny amount (often a few tens milligrams) of porcelain material, more than 40 element concentrations and Sr-Nd isotopic compositions can be rapidly and precisely determined on the ICP-MS and TIMS, respectively. The analytical results show that visibly similar Chinese porcelains made in different places and/or dynasties are strikingly distinctive. The data also allow modern fakes to be readily distinguished from antique porcelains. (author). 4 refs., 7 figs

Application of nuclear analysis techniques in ancient chinese porcelain

International Nuclear Information System (INIS)

Feng Songlin; Xu Qing; Feng Xiangqian; Lei Yong; Cheng Lin; Wang Yanqing

2005-01-01

Ancient ceramic was fired with porcelain clay. It contains various provenance information and age characteristic. It is the scientific foundation of studying Chinese porcelain to analyze and research the ancient ceramic with modern analysis methods. According to the property of nuclear analysis technique, its function and application are discussed. (authors)

Moessbauer study of the Ru porcelain of Chinese Song Dynasty and Yuan Dynasty

International Nuclear Information System (INIS)

Gao Zhengyao; Chen Xiande

1994-01-01

The Moessbauer spectra from the glazes of the Song Dynasty and the Yuan Dynasty Ru porcelains and the imitative ancient Ru porcelain are compared and analyzed. It is determined that the original firing atmosphere of the Yuan Dynasty Ru porcelain was reductive. The firing temperature was 1250 ± 20 C. The original firing atmosphere of the Song Dynasty Ru porcelain was also reductive; the firing temperature was above 1200 C. The coloring mechanism of these glazes is discussed. (orig.)

Simulation of Contamination Deposition on Typical Shed Porcelain Insulators

Directory of Open Access Journals (Sweden)

Yukun Lv

2017-07-01

Full Text Available The contamination deposition characteristics of insulators can be used in the development of antifouling work. Using COMSOL software, numerical simulations on the pollution-deposited performance of a porcelain three-umbrella insulator and porcelain bell jar insulator in a wind tunnel were conducted, and the simulated results were compared with the tested results. The comparison shows that the deposit amount is consistent with the order of magnitude and presents a similar tendency with Direct Current (DC voltage variation; then the rationality of the simulation is verified. Based on these results, simulations of the natural contamination deposition on porcelain insulators and the distribution of pollution along the umbrella skirt were performed. The results indicates that, under a same wind speed, contamination of the porcelain three-umbrella insulator and porcelain bell jar insulator under DC voltage was positively correlated with the particle size. With the same particle size, the proportion of the deposit amount under DC voltage (NSDDDC to the deposit amount under AC voltage (NSDDAC of both insulators decreases with the increase in wind speed. However, the ratio increases as particle size increase. At a small wind speed, the deposit amount along the umbrella skirt of the two insulators displays a U-shaped distribution under DC voltage while there is little difference in the contamination amount of each skirt under Alternating Current (AC voltage.

Porcelain gallbladder: The rare end of the spectrum of chronic cholecystitis.

OpenAIRE

Anand JALIHAL; Mohannur Sokanathan MATHIAZHAGAN; Vui Heng CHONG

2012-01-01

Porcelain gallbladder is an uncommon manifestation of chronic cholecystitis. The wall of the gallbladder becomes hard, calcified and brittle with a bluish–white tinge which resembles a porcelain ceramic. This condition is associated with increased risk of malignancy. We report two cases, both female patients (both 56 years old) who were diagnosed with porcelain gallbladder. One presented with a pyogenic liver abscess and the other was diagnosed to have gallbladder carcinoma on the background ...

Mechanical and chemical analyses across dental porcelain fused to CP titanium or Ti6Al4V

International Nuclear Information System (INIS)

Souza, Júlio C.M.; Henriques, Bruno; Ariza, Edith; Martinelli, Antonio E.; Nascimento, Rubens M.; Silva, Filipe S.; Rocha, Luís A.; Celis, Jean-Pierre

2014-01-01

The aim of this study was to evaluate the evolution of mechanical properties and chemical variation across veneering dental porcelain fused to different titanium-based substrates. Test samples were synthesized by fusing dental feldspar-based porcelain onto commercially pure titanium grade II or Ti6Al4V alloy. Samples were cross-sectioned at angles of 10 and 90° to the interface plane. Afterwards, nanoindentation tests and Scanning Electron Microscopy (SEM) imaging coupled to an Energy Dispersive Spectroscopy (EDS) system were carried out across interfaces extending from the metal towards the porcelain area. Elemental diffusion profiles across the porcelain-to-metal interfaces were also obtained by EDS analysis. The mismatch in mechanical properties found in porcelain-to-Ti6Al4V interfaces was lower than that of porcelain-to-CP titanium. Cracking was noticed at low-thickness veneering dental porcelain regions after the nanoindentation tests of samples cross-sectioned at low angles to the interface plane. A wide reaction zone between titanium and porcelain as well as higher incidence of defects was noticed at the porcelain-to-CP titanium interfaces. This study confirmed Ti6Al4V as an improved alternative to CP-titanium as it showed to establish a better interface with the veneering dental porcelain considering the slight chemical interaction and the lower mechanical properties mismatch. The elastic modulus of porcelain-to-Ti6Al4V samples showed to be less sensitive to porcelain thickness variations. - Highlights: • This study reveals mechanical and chemical behaviors across porcelain/titanium interfaces. • Cracks were noticed after nanoindentation on thin porcelain layers. • Ti6Al4V/porcelain showed a better mechanical behavior than that at CP-Ti/porcelain

Exams for attribution of sevres porcelain by x-ray fluorescence in Havana museums

International Nuclear Information System (INIS)

Mendoza Cuevas, Ariadna; Nazco Torres, Julio

2010-01-01

Analysis with X-ray fluorescence on Sevres porcelain was performed in order to determine criteria from the scientific examination that may support the attribution of special pieces. Multielemental chemical analyses of decorations colours, marks and glazed porcelain body were related to specific historic information about used materials and procedure of Sevres french manufactory. The used portable XRF spectrometer allows non destructive and in situ studies of Havana's collections with adequate sensibility for this application. Collections of Havana City Museum, Decorative Art Museum and Napoleonic Museum and some pieces of different background were studied. Non typical pigments used in Sevres allows to identify non genuine Sevres decorations while cluster analysis on porcelain body differentiates Sevres and 'surdecor' porcelains from Sevres style non genuine porcelains. (author)

Exams for attribution of sevres porcelain by x-ray fluorescence in Havana museums

International Nuclear Information System (INIS)

Mendoza Cuevas, Ariadna; Nazco Torres, Julio

2009-01-01

Analysis with X-ray fluorescence on Sevres porcelain was performed in order to determine criteria from the scientific examination that may support the attribution of special pieces. Multielemental chemical analyses of decorations colours, marks and glazed porcelain body were related to specific historic information about used materials and procedure of Sevres french manufactory. The used portable XRF spectrometer allows non destructive and in situ studies of Havana's collections with adequate sensibility for this application. Collections of Havana City Museum, Decorative Art Museum and Napoleonic Museum and some pieces of different background were studied. Non typical pigments used in Sevres allows to identify non genuine Sevres decorations while cluster analysis on porcelain body differentiates Sevres and 'surdecor' porcelains from Sevres style non genuine porcelains. (author)

Porcelain tiles by the dry route

International Nuclear Information System (INIS)

Melchiades, F. G.; Daros, M. T.; Boschi, A. O.

2010-01-01

In Brazil, the second largest tile producer of the world, at present, 70% of the tiles are produced by the dry route. One of the main reasons that lead to this development is the fact that the dry route uses approximately 30% less thermal energy them the traditional wet route. The increasing world concern with the environment and the recognition of the central role played by the water also has pointed towards privileging dry processes. In this context the objective of the present work is to study the feasibility of producing high quality porcelain tiles by the dry route. A brief comparison of the dry and wet route, in standard conditions industrially used today to produce tiles that are not porcelain tiles, shows that there are two major differences: the particle sizes obtained by the wet route are usually considerably finer and the capability of mixing the different minerals, the intimacy of the mixture, is also usually better in the wet route. The present work studied the relative importance of these differences and looked for raw materials and operational conditions that would result in better performance and glazed porcelain tiles of good quality. (Author) 7 refs.

Provenance study of ancient Chinese Yaozhou porcelain by neutron activation analysis

Science.gov (United States)

Li, G. X.; Y Gao, Z.; Li, R. W.; Zhao, W. J.; Xie, J. Z.; Feng, S. L.; Zhuo, Z. X.; Y Fan, D.; Zhang, Y.; Cai, Z. F.; Liu, H.

2003-09-01

This paper reports our study of the provenance of ancient Chinese Yaozhou porcelain. The content of 29 elements in the Yaozhou porcelain samples was measured by neutron activation analysis (NAA). The NAA data were further analysed using fuzzy cluster analysis to obtain the trend fuzzy cluster diagrams. These samples with different glaze colour, ranging over more than 700 years, were fired in different kilns. Our analysis indicates the relatively concentrated distribution of the sources of the raw material for the Yaozhou porcelain body samples. They can be classified into two independent periods, i.e. the Tang (AD 618-907) and the Five Dynasties (AD 907-960) period, and the Song (AD 960-1279) and Jin (AD 1115-1234) period. Our analysis also indicates that the sources of the raw material for the ancient Yaozhou porcelain glaze samples are quite scattered and those for the black glaze in the Tang Dynasty are very concentrated. The sources of the raw material for the celadon glaze and the white glaze in the Tang Dynasty are widely distributed and those for the celadon glaze in the Song Dynasty are close to those of the bluish white glaze in the Jin Dynasty, and they are very concentrated. The sources of the raw material for the porcelain glazes cover those of the porcelain bodies.

Relation between the microstructure and technological properties of porcelain stoneware. A review

OpenAIRE

Romero, M.; Pérez, J. M.

2015-01-01

Porcelain stoneware is a strongly sintered ceramic material fabricated from ball clays-quartz-feldspar mixtures. Porcelain stoneware is characterized by its excellent technical and functional properties (low water absorption, high mechanical properties, resistant to chemical substances and cleaning agents, aesthetic possibilities …). These characteristic and technical features make that among the different types of ceramic tile, porcelain stoneware is the ceramic product that in the last year...

Effects of different polishing techniques on the surface roughness of dental porcelains

Directory of Open Access Journals (Sweden)

Işil Sarikaya

2010-02-01

Full Text Available OBJECTIVE: The purpose of this study was to evaluate the effects of different polishing techniques on the surface roughness of dental porcelains. MATERIAL AND METHODS: Fifty-five cylindirical specimens (15x2 mm were prepared for each feldspathic (Vita VMK 95, Ceramco III and low-fusing dental porcelain (Matchmaker. Fifty-five specimens of machinable feldspathic porcelain blocks (Vitablocs Mark II, (12x14x18 mm were cut into 2-mm-thick slices (12x14 mm with low speed saw. The prepared specimens were divided into 11 groups (n=5 representing different polishing techniques including control ((C no surface treatment, glaze (G and other 9 groups that were finished and polished with polishing discs (Sof-Lex (Sl, two porcelain polishing kits (NTI (Pk, Dialite II (Di, a diamond polishing paste (Sparkle (Sp, a zirconium silicate based cleaning and polishing prophy paste (Zircate (Zr, an aluminum oxide polishing paste (Prisma Gloss (Pg, and combinations of them. The surface roughness of all groups was measured with a profilometer. The data were analyzed with a 2-way analysis of variance, and the mean values were compared by the Tukey Honestly Significant Difference test (a=0.05. RESULTS: For all porcelain material groups, the lowest Ra values were observed in Group Gl, Group Sl, Group Pk, and Group Di, which were not significantly different from each other (p>0.05.When comparing the 4 different porcelain materials, the machinable feldspathic porcelain block group (Mark II demonstrated statistically significantly less Ra values than the other porcelain materials tested (p<0.05. No significant difference was observed between the VMK 95 and Ceramco III porcelain groups (p=0.919, also these groups demonstrated the highest Ra values. CONCLUSION: Subjected to surface roughness, the surfaces obtained with polishing and/or cleaning-prophy paste materials used alone were rougher compared to the surfaces finished using Sof-lex, Dialite, and NTI polishing kit

Sexual Biofilm Formation in Candida tropicalis Opaque Cells

Science.gov (United States)

Jones, Stephen K.; Hirakawa, Matthew P.; Bennett, Richard J.

2014-01-01

Summary Candida albicans and Candida tropicalis are opportunistic fungal pathogens that can transition between white and opaque phenotypic states. White and opaque cells differ both morphologically and in their responses to environmental signals. In C. albicans, opaque cells respond to sexual pheromones by undergoing conjugation, while white cells are induced by pheromones to form sexual biofilms. Here, we show that sexual biofilm formation also occurs in C. tropicalis but, unlike C. albicans, biofilms are formed exclusively by opaque cells. C. tropicalis biofilm formation was dependent on the pheromone receptors Ste2 and Ste3, confirming the role of pheromone signaling in sexual biofilm development. Structural analysis of C. tropicalis sexual biofilms revealed stratified communities consisting of a basal layer of yeast cells and an upper layer of filamentous cells, together with an extracellular matrix. Transcriptional profiling showed that genes involved in pheromone signaling and conjugation were upregulated in sexual biofilms. Furthermore, FGR23, which encodes an agglutinin-like protein, was found to enhance both mating and sexual biofilm formation. Together, these studies reveal that C. tropicalis opaque cells form sexual biofilms with a complex architecture, and suggest a conserved role for sexual agglutinins in mediating mating, cell cohesion and biofilm formation. PMID:24612417

Analysis of elemental composition of porcelains unearthed from Waguantan kiln site by PIXE–RBS

International Nuclear Information System (INIS)

Zhou, Z.; Zhang, K.; Xia, C.D.; Liu, M.T.; Zhu, J.J.; An, Z.; Bai, B.

2015-01-01

Highlights: •We analyzed 61 unearthed porcelain shards in Yuan Dynasty by PIXE–RBS. •An electron gun was installed to solve the electric charge accumulations. •The factor analysis was performed for the element compositions. •The “exotic group” porcelain samples unearthed were produced locally. -- Abstract: A method combining proton-induced X-ray emission spectrometry (PIXE) and Rutherford backscattering spectrometry (RBS) was used to determine the composition of 61 porcelain shards from the Yuan Dynasty (1271–1368 A.D.) unearthed from the Waguantan kiln site at Tianzhu County in Guizhou Province, China. Based on our previous experimental setup, an electron gun device with a LaB 6 crystal cathode was installed to solve the problem created when the incident proton beams generated electric charge accumulations on the surfaces of the insulating porcelain samples, which induced a large bremsstrahlung background. The use of the electron gun has largely eliminated the large bremsstrahlung background and has therefore improved the detection limits for elements, especially for trace elements, and made it possible to determine the origin of the porcelains based on the trace elements. Major and trace elemental compositions of the porcelain bodies and glazes measured by PIXE and RBS were analyzed by the factor analysis method. The factor analysis showed that a few pieces of porcelain with a style similar to the porcelain of the Longquan kiln among the unearthed porcelains from the Waguantan kiln site did not have obvious differences in elemental compositions from other remaining porcelains unearthed from the Waguantan kiln site, indicating that the pieces of unearthed porcelain with the Longquan kiln style did in fact belong to the product fired locally by imitating the model of the Longquan celadon with local raw materials. This result therefore indicated that the Longquan kiln technology that originated from the Five Dynasties (907–960 A.D.) had been

Analysis of elemental composition of porcelains unearthed from Waguantan kiln site by PIXE–RBS

Energy Technology Data Exchange (ETDEWEB)

Zhou, Z. [Key Laboratory of Radiation Physics and Technology of Ministry of Education, Institute of Nuclear Science and Technology, Sichuan University, Chengdu 610064 (China); Zhang, K. [School of History and Culture, Sichuan University, Chengdu 610064 (China); Xia, C.D.; Liu, M.T.; Zhu, J.J. [Key Laboratory of Radiation Physics and Technology of Ministry of Education, Institute of Nuclear Science and Technology, Sichuan University, Chengdu 610064 (China); An, Z., E-mail: anzhu@scu.edu.cn [Key Laboratory of Radiation Physics and Technology of Ministry of Education, Institute of Nuclear Science and Technology, Sichuan University, Chengdu 610064 (China); Bai, B., E-mail: baibin@scu.edu.cn [School of History and Culture, Sichuan University, Chengdu 610064 (China)

2015-03-01

Highlights: •We analyzed 61 unearthed porcelain shards in Yuan Dynasty by PIXE–RBS. •An electron gun was installed to solve the electric charge accumulations. •The factor analysis was performed for the element compositions. •The “exotic group” porcelain samples unearthed were produced locally. -- Abstract: A method combining proton-induced X-ray emission spectrometry (PIXE) and Rutherford backscattering spectrometry (RBS) was used to determine the composition of 61 porcelain shards from the Yuan Dynasty (1271–1368 A.D.) unearthed from the Waguantan kiln site at Tianzhu County in Guizhou Province, China. Based on our previous experimental setup, an electron gun device with a LaB{sub 6} crystal cathode was installed to solve the problem created when the incident proton beams generated electric charge accumulations on the surfaces of the insulating porcelain samples, which induced a large bremsstrahlung background. The use of the electron gun has largely eliminated the large bremsstrahlung background and has therefore improved the detection limits for elements, especially for trace elements, and made it possible to determine the origin of the porcelains based on the trace elements. Major and trace elemental compositions of the porcelain bodies and glazes measured by PIXE and RBS were analyzed by the factor analysis method. The factor analysis showed that a few pieces of porcelain with a style similar to the porcelain of the Longquan kiln among the unearthed porcelains from the Waguantan kiln site did not have obvious differences in elemental compositions from other remaining porcelains unearthed from the Waguantan kiln site, indicating that the pieces of unearthed porcelain with the Longquan kiln style did in fact belong to the product fired locally by imitating the model of the Longquan celadon with local raw materials. This result therefore indicated that the Longquan kiln technology that originated from the Five Dynasties (907–960 A.D.) had been

Mössbauer study of the Ru porcelain of Chinese Song Dynasty and Yuan Dynasty

Science.gov (United States)

Zhengyao, Gao; Songhua, Chen; Xiande, Chen

1994-12-01

The Mössbauer spectra from the glazes of the Song Dynasty and the Yuan Dynasty Ru porcelains and the imitative ancient Ru porcelain are compared and analyzed. It is determined that the original firing atmosphere of the Yuan Dynasty Ru porcelain was reductive. The firing temperature was 1250±20 ‡C. The original firing atmosphere of the Song Dynasty Ru porcelain was also reductive; the firing temperature was above 1200 ‡C. The coloring mechanism of these glazes is discussed.

Bond strength of the porcelain repair system to all-ceramic copings and porcelain.

Science.gov (United States)

Lee, Sang J; Cheong, Chan Wook; Wright, Robert F; Chang, Brian M

2014-02-01

The purpose of this study was to investigate the shear bond strength of the porcelain repair system on alumina and zirconia core ceramics, comparing this strength with that of veneering porcelain. Veneering ceramic (n = 12), alumina core (n = 24), and zirconia core (n = 24) blocks measuring 10 × 5 × 5 mm(3) were fabricated. Veneering ceramic blocks were used as the control. Alumina and zirconia core blocks were divided into 2 groups (n = 12 each), and a slot (2 × 2 × 4 mm(3)) filled with veneering ceramics was prepared into one of the alumina and zirconia core groups (n = 12). Followed by surface treatments of micro-abrasion with 30 μm alumina particles, etching with 35% phosphoric acid and silane primer and bond, composite resin blocks (2 × 2 × 2 mm(3)) were built up and light polymerized onto the treated surfaces by 3 configurations: (a) composite blocks bonded onto veneering ceramic surface alone, (b) composite blocks bonded onto alumina core or zirconia core surfaces, (c) a 50% surface area of the composite blocks bonded to veneering ceramics and the other 50% surface area of the composite blocks to alumina core or zirconia core surfaces. The shear bond strength of the composite to each specimen was tested by a universal testing machine at a 0.5 mm/min crosshead speed. The shear bond strength was analyzed by unpaired t-tests for within the configuration groups and ANOVA for among the different configuration groups. When the mean shear bond strength was compared within groups of the same configuration, there were no statistically significant differences. Comparison of the shear bond strength among groups of different configurations revealed statistically significant differences. The mean shear bond strength of composite onto 100% veneering ceramic surface and composite onto 50% veneering 50% all-ceramic cores was statistically higher than that of composite onto 100% all-ceramic cores; however, the differences of the shear bond strength of composite bonded

Energy requirement for firing porcelain | M. de O. Madivate | Bulletin ...

African Journals Online (AJOL)

Results from studies on the ternary system Ribaué kaolin–Carapira feldspar– Marracuene quartz sands were used to test a procedure that we developed for calculation of the energy requirement for firing porcelain. Results obtained vary between 1300 and 1800 kJ/kg porcelain. These results differ largely from the ones ...

Analysis of elemental composition of porcelains unearthed from Waguantan kiln site by PIXE-RBS

Science.gov (United States)

Zhou, Z.; Zhang, K.; Xia, C. D.; Liu, M. T.; Zhu, J. J.; An, Z.; Bai, B.

2015-03-01

A method combining proton-induced X-ray emission spectrometry (PIXE) and Rutherford backscattering spectrometry (RBS) was used to determine the composition of 61 porcelain shards from the Yuan Dynasty (1271-1368 A.D.) unearthed from the Waguantan kiln site at Tianzhu County in Guizhou Province, China. Based on our previous experimental setup, an electron gun device with a LaB6 crystal cathode was installed to solve the problem created when the incident proton beams generated electric charge accumulations on the surfaces of the insulating porcelain samples, which induced a large bremsstrahlung background. The use of the electron gun has largely eliminated the large bremsstrahlung background and has therefore improved the detection limits for elements, especially for trace elements, and made it possible to determine the origin of the porcelains based on the trace elements. Major and trace elemental compositions of the porcelain bodies and glazes measured by PIXE and RBS were analyzed by the factor analysis method. The factor analysis showed that a few pieces of porcelain with a style similar to the porcelain of the Longquan kiln among the unearthed porcelains from the Waguantan kiln site did not have obvious differences in elemental compositions from other remaining porcelains unearthed from the Waguantan kiln site, indicating that the pieces of unearthed porcelain with the Longquan kiln style did in fact belong to the product fired locally by imitating the model of the Longquan celadon with local raw materials. This result therefore indicated that the Longquan kiln technology that originated from the Five Dynasties (907-960 A.D.) had been propagated to the Waguantan kiln site of Guizhou Province in the Yuan Dynasty.

White-and-blud porcelain of Hutian kiln in Ming dynasty studied by PIXE

International Nuclear Information System (INIS)

Cheng Lin; Feng Songlin; Sha Yin; Cheng Huansheng

2004-01-01

The study of provenance, ages and distinguishing precious ancient porcelain from a fake of Chinese ancient porcelain by modern technologies arose greatly interesting in the circles of archaeologists and scientists in China. Concentration of major and trace elements of white-and-blue porcelain of Hutian kiln in Ming Dynasty were analyzed by PIXE, and elemental distributions of porcelain were analyzed by SPM. The results indicate the elemental distributions in the white glaze, blue glaze and body are homogeneous, respectively. It is a layer nearly 5-10 μm between the body and blue glaze. Probably, cobalt blue pigment used in the blue glaze comes from Jiangxi, Fujian province etc. (authors)

Preparation of porcelain tile granulates by more environmentally sustainable processes

Energy Technology Data Exchange (ETDEWEB)

Gil, C.; Silvestre, D.; Piquer, J.; Garcia-Ten, J.; Quereda, E.; Vicente, M. J.

2012-07-01

This study examines the feasibility of manufacturing glazed porcelain tiles with a more environmentally friendly manufacturing process, by reducing water and thermal energy consumption. The process studied in this paper is dry milling in a pendulum mill, with subsequent granulation (in order to obtain a press powder with similar flow ability to that of spray dried powders). The different morphology of the new granulate with respect to the standard spray-dried granulate modifies the microstructure of the green compacts and thus, their behaviour and fired tile properties. In order to obtain porcelain tiles with the required properties (water absorption, mechanical strength,) changes have been made in the raw materials mixture and in the processing variables. Finally, porcelain tiles measuring 50x50 cm have been manufactured at industrial scale with the new granulate using a conventional firing cycle, obtaining quality levels identical to those provided by the spray-dried granulate. These results open the possibility of preparing porcelain tile body compositions through a manufacturing process alternative to the standard one, more environmentally friendly and with lower costs. (Author)

Study of provenance properties on ancient porcelain of Yue Kiln at Si-long-kou with NAA

International Nuclear Information System (INIS)

Feng Songlin; Fan Dongyu; Feng Xiangqian; Cheng Lin; Lei Yong; Xu Qing; Quan Huishan; Shen Yueming; Zhou Zhexi; Zhang Wenjiang

2005-01-01

Chinese ancient porcelain history has lasted about three thousands years from Shang Dynasty (1100∼1600 BC). A large amount of ancient porcelain sherds with accuracy provenance and ages were excavated from a lot of kiln sites in China. Archaeologists and ceramic experts have recognized and researched it with excavated stratum, utensil shape, body quality, glaze color and painting pattern. However, the appearance characteristic of some ancient porcelain manufactured in different kilns is similar. Therefore, it is still difficult to identify the provenance and ages of the samples excavated from some sites using traditional methods. Up, to now, many problems of Chinese ancient porcelain are confused for archaeologist and collecting experts. The elemental composition of ancient porcelain shows certain information of provenance and age. Especially, the sorts and contents of the elements in porcelain didn't change, so it is very useful to determine the provenance of ancient porcelain with elemental composition characteristics. Provenance characteristic is the important scientific information to identify ancient porcelain wares excavated from sites and graves. The porcelain samples of Si-Long-Kou Yue kiln in Zhejiang Province of china have been analyzed with NAA in this paper. The provenance characteristic was compared with it of Hong-Zhou kiln of Jiang-Xi Province and Yao-Zhou kiln of Shan-Xi Province. The experimental data were studied with statistic methods. The results show that the chemical compositions of porcelain body samples for three kilns were different. The difference was been able identified. The porcelain body materials of both Si-Long-Kou Yue kiln and Hong-Zhou kiln of Jiang-Xi were similar. The samples of Yao-Zhou kiln in north of China existed obvious difference.

The Earliest Chinese Proto-Porcelain Excavated from Kiln Sites: An Elemental Analysis

OpenAIRE

Li, Yu; Zhang, Bin; Cheng, Huansheng; Zheng, Jianming

2015-01-01

In June 2012, the Piaoshan kiln site was excavated in Huzhou, Zhejiang Province, which hitherto proved to be the earliest known Chinese proto-porcelain kiln. Judging from the decorative patterns of unearthed impressed stoneware and proto-porcelain sherds, the site was determined to date to the late Xia (c. 2070-c. 1600 BC), the first dynasty of China. Here, we report on proton-induced X-ray emission analyses of 118 proto-porcelain and 35 impressed stoneware sherds from Piaoshan and five subse...

Effect of laser parameters on the microstructure of bonding porcelain layer fused on titanium

Science.gov (United States)

Chen, Xiaoyuan; Guo, Litong; Liu, Xuemei; Feng, Wei; Li, Baoe; Tao, Xueyu; Qiang, Yinghuai

2017-09-01

Bonding porcelain layer was fused on Ti surface by laser cladding process using a 400 W pulse CO2 laser. The specimens were studied by field-emission scanning electron microscopy, X-ray diffraction and bonding tests. During the laser fusion process, the porcelain powders were heated by laser energy and melted on Ti to form a chemical bond with the substrate. When the laser scanning speed decreased, the sintering temperature and the extent of the oxidation of Ti surface increased accordingly. When the laser scanning speed is 12.5 mm/s, the bonding porcelain layers were still incomplete sintered and there were some micro-cracks in the porcelain. When the laser scanning speed decreased to 7.5 mm/s, vitrified bonding porcelain layers with few pores were synthesized on Ti.

Micro SR-XRF analysis on underglaze copper red porcelain of ming dynasty

International Nuclear Information System (INIS)

Guan Li; Zhu Jian; Yang Yimin; Fan Changsheng; Chen Dongliang; Xu Wei; Zhang Jing; Wang Lihua

2013-01-01

Background: The firing techniques of producing underglaze copper red porcelain emerged in the Yuan dynasty and reached its maturity during the Ming and Qing Dynasties in Jingdezhen city. The technique of producing underglaze red porcelain was sensitive to the firing temperature and atmosphere, so it was very hard to produce and also difficult to display red color under the surface successfully. Purpose and Methods: The micro SR-XRF technique was employed to analysis a piece of sherd of underglaze copper red porcelain of early Ming dynasty. The Chemical compositions of glaze and color areas were presented, and the elemental contents in different color areas were obtained by using line-scanning techniques. Results: Some elements such as As and Pb were contained in raw materials, and the content of Cu had obviously increased with the color changing from gray to red. The results indicated that the nature mineral possibly used as the pigment for underglazed copper red porcelain coloration, and the color appearance also depends on the amount of copper in the pigments contained. Conclusions: This paper presents the advantage of the synchrotron radiation XRF technology and contributes to the science evidences for the Chinese ancient porcelain handcraft research. (authors)

Fuzzy cluster analysis on trace elements of Hangzhou Jiaotan Guan Porcelain

International Nuclear Information System (INIS)

Gao Zhengyao; Liu Youe; Chen Songhua

1997-01-01

Forty samples of South Song 'Jiaotan Guankiln' are analyzed by neutron activation analysis (NAA). The 36 trace element contents in every sample are determined. This trace elements are analyzed by fuzzy cluster method. The result shows that the source of glaze raw material of South Song Guan porcelain is clearly different from that of the body raw material. For Guan kiln of South Song dynasty there was a very stable and lasting source of raw material of glaze and body. The archaeological problems are clarified. The glaze material and body material of modern Guan porcelain are different from those of the ancient Guan Porcelain

Sintering and dielectric properties of a technical porcelain prepared from economical natural raw materials

Directory of Open Access Journals (Sweden)

S. Kasrani

Full Text Available Abstract In this study, the production of a technical porcelain, for the ceramic dielectric applications by using economical natural raw materials, was investigated. The basic porcelain composition was selected consisting of 30 wt% kaolin, 45 wt% potash-feldspar and 25 wt% quartz. The obtained phases in the sintered samples were investigated by X-ray diffraction, Fourier transform infrared spectroscopy analysis, and scanning electron microscopy images. It has been confirmed by these techniques that the main crystalline phases were quartz and mullite. Dielectric measurements of technical porcelains have been carried out at 1 kHz from room temperature to 200 °C. The dielectric constant, loss factor, dielectric loss tangent, and resistivity of the porcelain sample sintered at 1160 °C were 22-25, 0.32-1.80, 0.006-0.07, and 0.2-9 x 1013 Ω.cm, respectively. The value of dielectric constant was significantly high when compared to that of conventional porcelains which did not exceed generally 9.

Sintering and dielectric properties of a technical porcelain prepared from economical natural raw materials

Energy Technology Data Exchange (ETDEWEB)

Kasrani, S.; Harabi, A.; Barama, S.-E.; Foughali, L.; Benhassine, M. T., E-mail: souad478@yahoo.fr, E-mail: harabi52@gmail.com, E-mail: sebarama@usa.com, E-mail: foughali_lazhar@yahoo.fr, E-mail: mtb25dz@gmail.com [Ceramics Lab. Mentouri University of Constantine (Algeria); Aldhayan, D.M., E-mail: aldhayan@ksu.edu.sa [Chemistry Department, Riyadh, King Saud University (Saudi Arabia)

2016-10-15

In this study, the production of a technical porcelain, for the ceramic dielectric applications by using economical natural raw materials, was investigated. The basic porcelain composition was selected consisting of 30 wt% kaolin, 45 wt% potash-feldspar and 25 wt% quartz. The obtained phases in the sintered samples were investigated by X-ray diffraction, Fourier transform infrared spectroscopy analysis, and scanning electron microscopy images. It has been confirmed by these techniques that the main crystalline phases were quartz and mullite. Dielectric measurements of technical porcelains have been carried out at 1 kHz from room temperature to 200 °C. The dielectric constant, loss factor, dielectric loss tangent, and resistivity of the porcelain sample sintered at 1160 °C were 22-25, 0.32-1.80, 0.006-0.07, and 0.2-9 x 10{sup 13} Ω.cm, respectively. The value of dielectric constant was significantly high when compared to that of conventional porcelains which did not exceed generally 9. (author)

Sintering and dielectric properties of a technical porcelain prepared from economical natural raw materials

International Nuclear Information System (INIS)

Kasrani, S.; Harabi, A.; Barama, S.-E.; Foughali, L.; Benhassine, M. T.; Aldhayan, D.M.

2016-01-01

In this study, the production of a technical porcelain, for the ceramic dielectric applications by using economical natural raw materials, was investigated. The basic porcelain composition was selected consisting of 30 wt% kaolin, 45 wt% potash-feldspar and 25 wt% quartz. The obtained phases in the sintered samples were investigated by X-ray diffraction, Fourier transform infrared spectroscopy analysis, and scanning electron microscopy images. It has been confirmed by these techniques that the main crystalline phases were quartz and mullite. Dielectric measurements of technical porcelains have been carried out at 1 kHz from room temperature to 200 °C. The dielectric constant, loss factor, dielectric loss tangent, and resistivity of the porcelain sample sintered at 1160 °C were 22-25, 0.32-1.80, 0.006-0.07, and 0.2-9 x 10 13 Ω.cm, respectively. The value of dielectric constant was significantly high when compared to that of conventional porcelains which did not exceed generally 9. (author)

Study on the pre-qin pottery and proto-porcelain from boluo county, Guangdong province with INAA

International Nuclear Information System (INIS)

Wang Jianping; Chen Tiemei

2003-01-01

Seventy-seven pottery and proto-porcelain sherds collected from Meihuadun, Yingang and Henglingshan sites of Boluo County, Guangdong Province were studied with INAA. These sherds are of Western Zhou to Warring States Period. Concentrations of 27 elements were measured, then principal component analysis and other statistical procedures were applied to the data set in order to classify these sherds. This study shows: (1) Though these 3 archaeological sites are located close to each other within an area of about 1000 km 2 , ancient potters of these sites might use raw materials of different origins for pottery production, as pottery sherds of these 3 sites show different chemical compositions. Such differentiation is also observed for the proto-porcelain samples, indicating that proto-porcelain samples found at Meihuadun and Henglingshan might be of different provenance; (2) In each site during the Western Zhou to Spring-Autumn Period the same raw material was used for both hard pottery and soft pottery manufacturing, while during the Warring States Period no similarity in chemical compositions was observed between hard pottery and soft pottery samples. It is wondered if this phenomenon means an advancement of ceramic technology

Opaque Watercolor (Tentative Course Outline). Art Education: 6673.05.

Science.gov (United States)

Greenaway, Jean E.

This tentative course outline is for use in one of the Quinmester Program classes, Opaque Watercolor. Designed for students in grades 7-12, with no prerequisite, the course includes the introduction of a variety of techniques in a number of opaque media including tempera, gouache, and cassein. Matting and mounting techniques are also taught. A…

‪Joint Opaque Selling Systems for Online Travel Agencies‪

OpenAIRE

Malgorzata Ogonowska; Dominique Torre

2014-01-01

?This paper analyses the properties of sophisticated opaque booking systems, implemented by online travel agencies in conjunction, usually, with traditional transparent systems. We characterize the opaque products as opposed to traditional transparent products. We focus on the two particular distribution models: opaque posted price system developed by Hotwire.com, and the Name-Your-Own-Price system developed by Priceline.com. We propose an analytical model to compare the results of individual...

Joint Opaque booking systems for online travel agencies

OpenAIRE

Ogonowska , Malgorzata; Torre , Dominique

2010-01-01

This paper analyzes the properties of the advanced Opaque booking systems used by the online travel agencies in conjunction with their traditional transparent booking system. In section 2 we present an updated literature review. This review underlines the interest and the specicities of Opaque goods in the Tourism Industry. It also characterizes properties of the Name-Your-Own-Price (NYOP) channel introduced by Priceline and oering probabilistic goods to potential travelers. In the section 3 ...

PIXE analysis of proto-porcelain excavated from the Huoshaoshan kiln site in Deqing County, Zhejiang Province

International Nuclear Information System (INIS)

Zhang Bin; Cheng Huansheng; Zheng Jianming

2014-01-01

Background: Zhejiang Province is an important producing area of proto-porcelain. Huoshaoshan kiln site in Deqing County is the only kiln known currently for firing proto-porcelain from the late Western Zhou Dynasty to the late Spring and Autumn Period. Also it is the earliest kiln site unearthed for only firing proto-porcelain so far. It is of great significance for the exploration of Chinese early celadon firing technology. Purpose: The aim is to disclose the elemental characteristics of these proto-porcelains and study the sources of the raw materials and relationship between these proto-porcelains. Methods: We selected 18 samples made at the early period (from the late Western Zhou Dynasty to the early Spring and Autumn Period), 15 samples made at the middle and last period (the last period of the middle Spring and Autumn Period), and 17 samples made at the last period (the last period of the late Spring and Autumn Period). Proton Induced X-ray Emission (PIXE) was used to analyze these samples and measure the chemical compositions of these proto-porcelains. The factor analysis is used to study the sources of the raw materials and relationship between these proto-porcelains made in the different periods. Results: The results show that for the raw materials of body and glaze, the proto-porcelains at the last period are different from those at the early period, while the same as those at the middle and last period. Conclusion: PIXE combining with factor analysis can be used to study effectively the sources of the raw materials and relationship between these proto-porcelains. (authors)

Distribution of uranium in dental porcelains by means of the fission track method

International Nuclear Information System (INIS)

Shimizu, Masami; Noguchi, Kunikazu; Moriwaki, Kazunari; Sairenji, Eiko

1980-01-01

Porcelain teeth, some of which contain uranium compounds for aesthetic purpose, have been widely used in dental clinics. Hazardous effects due to uranium radiation have been suggested by recent publications. In the previous study, the authors reported the uranium content of porcelain teeth and radiation dose by it. In this study, using the fission track method, the authors examined spatial distribution of uranium in dental porcelain teeth (4 brands) which were marketed in Japan. From each sample of porcelain tooth, a 1-mm-thick specimen was sliced, and uranium content was measured at every 0.19 mm from labial side to lingual side for making a uranium distribution chart. Higher uranium concentration was found in Trubyte Bioblend porcelain teeth (USA) and they showed almost uniform distribution of uranium, while those of the Japanese three brands indicated, in most case, comparatively lower concentration and found to be non-uniform distributions. Range of uranium concentration in these brands were N.D. -- 5.2 ppm (Shofu-Ace), N.D. -- 342 ppm (Shofu-Real), N.D. -- 47 ppm (G.C. Livdent) and N.D. -- 235 ppm (Trubyte Bioblend), respectively. (author)

Application of INAA in analysis of Chinese ancient greenish white porcelain

International Nuclear Information System (INIS)

Lin Cheng; Songlin Feng; Rongwu Li

2009-01-01

This paper reports the applications of INAA in analysis of Chinese ancient porcelain fired from early Northern Song dynasty (AD 1004-1127) to Late Yuan dynasty (AD 1320-1368) in Hutian Kiln. Minor and trace elements of 168 pieces of ancient porcelain bodies were determined by INAA. The results of factor analysis and some archaeological questions are also discussed in this paper. (author)

A study of the high-temperature signal characteristics in the thermoluminescence of porcelain

International Nuclear Information System (INIS)

Yin Gongming

2001-01-01

The thermoluminescence pre-dose technique for dating ancient porcelain was developed in many laboratories. This technique was the only method which could directly determine the age of old porcelain. But the thermoluminescence high-temperature signal (over 200 degree C) had not been studied. The authors conduced a preliminary study of the characteristic of thermoluminescence high-temperature signal, such as the TL natural glow curve, and the glow curves after beta or alpha irradiation. Most of the 32 ancient porcelains had thermoluminescence high temperature signal, and only one peak in their TL glow curve was found

Flexural strength of fluorapatite-leucite and fuorapatite porcelains exposed to erosive agents in cyclic immersion

Directory of Open Access Journals (Sweden)

Peerapong Junpoom

2011-04-01

Full Text Available OBJECTIVE: The aim of this study was to evaluate the fexural strength of two porcelain materials (IPS d.SIGN and IPS e.max Ceram exposed to erosive agents. MATERIAL AND METHODS: One hundred and twenty bar-shaped specimens were made from each of fuorapatite-leucite porcelain (IPS d.SIGN and fuorapatite porcelain (IPS e.max Ceram and divided into 8 groups of 15 specimens each. Six groups were alternately immersed in the following storage agents for 30 min: deionized water (control, citrate buffer solution, pineapple juice, green mango juice, cola soft drink and 4% acetic acid. Then, they were immersed for 5 min in deionized water at 37ºC. Seven cycles were completed, totalizing 245 min. A 7th group was continuously immersed in 4% acetic acid at 80ºC for 16 h. The final, 8th, group was stored dry at 37ºC for 245 min. Three-point bending tests were performed in a universal testing machine. The data were analyzed statistically by 2-way ANOVA, Tukey's HSD test and t-test at signifcance level of 0.05. RESULTS: The fexural strengths of all groups of each porcelain after exposure to erosive agents in cyclic immersion did not differ signifcantly (p>0.05. For both types of porcelain, dry storage at 37ºC yielded the highest fexural strength, though without signifcant difference from the other groups (p>0.05. The fexural strengths of all groups of fuorapatite porcelains were signifcantly higher (p<0.05 than those of the fuorapatite-leucite porcelains. CONCLUSIONS: This study demonstrated that the erosive agents evaluated did not affect the fexural strength of the tested dental porcelains.

Line scanning analysis of Dilingtou Yue porcelain in Southern Song Dynasty by SRXRF method

International Nuclear Information System (INIS)

Zhu Shoumei; Mao Zhenwei; Feng Min; Zhu Jian; Ling Xue; Sheng Yueming; Huang Yuying; He Wei

2004-01-01

The SRXRF line scanning analysis technique was used to measure the elements' content in the Dilingtou Yue porcelain sherd of Southern Song Dynasty from glaze to body. It is found that there exists a middle layer between the porcelain glaze and body. And a line scanning analysis comparison was made with the Ru porcelain in Northern Song Dynasty. There are some differences between them and the middle layer of Dilingtou Yue sherd is a little thinner than the Ru sherd's. And elements' content distributions in glaze are different from Ru porcelain's and the changes of contents from the surface to the inner side of glaze are undulatory. The results indicate that the differences may result from the different materials of body and the different kilns. (authors)

Porcelain surface alterations and refinishing after use of two orthodontic bonding methods.

Science.gov (United States)

Herion, Drew T; Ferracane, Jack L; Covell, David A

2010-01-01

To compare porcelain surfaces at debonding after use of two surface preparation methods and to evaluate a method for restoring the surface. Lava Ceram feldspathic porcelain discs (n = 40) underwent one of two surface treatments prior to bonding orthodontic brackets. Half the discs had sandblasting, hydrofluoric acid, and silane (SB + HF + S), and the other half, phosphoric acid and silane (PA + S). Brackets were debonded using bracket removing pliers, and resin was removed with a 12-fluted carbide bur. The surface was refinished using a porcelain polishing kit, followed by diamond polishing paste. Measurements for surface roughness (Ra), gloss, and color were made before bonding (baseline), after debonding, and after each step of refinishing. Surfaces were also examined by scanning electron microscopy (SEM). Data was analyzed with 2-way ANOVA followed by Tukey HSD tests (alpha = 0.05). The SB + HF + S bonding method increased Ra (0.160 to 1.121 microm), decreased gloss (41.3 to 3.7) and altered color (DeltaE = 4.37; P gloss (41.7 to 38.0) and color (DeltaE = 0.50). The measurements and SEM observations showed that changes were fully restored to baseline with refinishing. The PA + S method caused significantly less damage to porcelain than the SB + HF + S method. The refinishing protocol fully restored the porcelain surfaces.

A historical perspective of synthetic ceramic and traditional feldspathic porcelain.

Science.gov (United States)

Chu, Stephen; Ahmad, Irfan

2005-10-01

Ceramics were invented by the Chinese during the T'ang Dynasty, where they quickly became a precious commodity. By the early 18th Century, ceramics found its way into dentistry due to its high strength, biocompatibility, and malleability. Today, ceramic materials are a staple in dentistry, available in both naturally based and partially synthetic formulas. Most recently they have become available as quartz-glass synthetic materials manufactured under controlled conditions to eliminate the inconsistencies and impurities inherent in the naturally based counterpart. This article details the discovery of porcelain and its role as a precious substance throughout the world and time, from its initial use as ornamental earthenware to its practical application in modern dentistry. Upon reading this article, the reader should: Understand the historical significance of porcelain. Recognize the fundamental constituents and physical properties of both natural feldspathic porcelains and fully synthetic ceramics used in dentistry.

In vitro comparison of fracture load of implant-supported, zirconia-based, porcelain- and composite-layered restorations after artificial aging.

Science.gov (United States)

Komine, Futoshi; Taguchi, Kohei; Fushiki, Ryosuke; Kamio, Shingo; Iwasaki, Taro; Matsumura, Hideo

2014-01-01

This study evaluated fracture load of single-tooth, implant-supported, zirconia-based, porcelain- and indirect composite-layered restorations after artificial aging. Forty-four zirconia-based molar restorations were fabricated on implant abutments and divided into four groups, namely, zirconia-based all-ceramic restorations (ZAC group) and three types of zirconia-based composite-layered restorations (ZIC-P, ZIC-E, and ZIC groups). Before layering an indirect composite material, the zirconia copings in the ZIC-P and ZIC-E groups were primed with Clearfil Photo Bond and Estenia Opaque Primer, respectively. All restorations were cemented on the abutments with glass-ionomer cement and then subjected to thermal cycling and cyclic loading. All specimens survived thermal cycling and cyclic loading. The fracture load of the ZIC-P group (2.72 kN) was not significantly different from that of the ZAC group (3.05 kN). The fracture load of the zirconia-based composite-layered restoration primed with Clearfil Photo Bond (ZIC-P) was comparable to that of the zirconia-based all-ceramic restoration (ZAC) after artificial aging.

On the interfacial fracture of porcelain/zirconia and graded zirconia dental structures.

Science.gov (United States)

Chai, Herzl; Lee, James J-W; Mieleszko, Adam J; Chu, Stephen J; Zhang, Yu

2014-08-01

Porcelain fused to zirconia (PFZ) restorations are widely used in prosthetic dentistry. However, their susceptibility to fracture remains a practical problem. The failure of PFZ prostheses often involves crack initiation and growth in the porcelain, which may be followed by fracture along the porcelain/zirconia (P/Z) interface. In this work, we characterized the process of fracture in two PFZ systems, as well as a newly developed graded glass-zirconia structure with emphases placed on resistance to interfacial cracking. Thin porcelain layers were fused onto Y-TZP plates with or without the presence of a glass binder. The specimens were loaded in a four-point-bending fixture with the thin porcelain veneer in tension, simulating the lower portion of the connectors and marginal areas of a fixed dental prosthesis (FDP) during occlusal loading. The evolution of damage was observed by a video camera. The fracture was characterized by unstable growth of cracks perpendicular to the P/Z interface (channel cracks) in the porcelain layer, which was followed by stable cracking along the P/Z interface. The interfacial fracture energy GC was determined by a finite-element analysis taking into account stress-shielding effects due to the presence of adjacent channel cracks. The resulting GC was considerably less than commonly reported values for similar systems. Fracture in the graded Y-TZP samples occurred via a single channel crack at a much greater stress than for PFZ. No delamination between the residual glass layer and graded zirconia occurred in any of the tests. Combined with its enhanced resistance to edge chipping and good esthetic quality, graded Y-TZP emerges as a viable material concept for dental restorations. Copyright © 2014 Acta Materialia Inc. All rights reserved.

Radiotherapy-induced aortic valve disease associated with porcelain aorta

International Nuclear Information System (INIS)

Daitoku, Kazuyuki; Fukui, Kozo; Ichinoseki, Ikkoh; Munakata, Mamoru; Takahashi, Shoichi; Fukuda Ikuo

2004-01-01

Mediastinal irradiation has been reported to induce cardiac disease such as pericarditis, valvular dysfunction, conduction abnormalities, accelerated arteriosclerosis of the coronary arteries, and also calcifications of the ascending aorta. We herein describe a case of radiotherapy-induced porcelain aorta and aortic valve disease and their surgical treatment. The patient was diagnosed with myasthenia gravis (MG) in 1965 (Osserman's type II), and mediastinal irradiation was performed in 1970 for treatment of thymic tumor associated with MG. Thirty years after radiation therapy, complete atrioventricular block and aortic valve disease with severe calcification of the ascending aorta and aortic arch (porcelain aorta) were detected on echo cardiogram and cardiac catheterization. A permanent pacemaker was implanted via the left subclavian vein and aortic valve replacement was performed under extracorporeal circulation established by selective cerebral perfusion and balloon occlusion instead of aortic cross-clamping. As no risk factors of arteriosclerosis such as hypercholesterolemia, hyperglycemia and hypertension were apparent, we concluded that the aortic valve disease and porcelain aorta were primarily induced by radiotherapy. (author)

Surface topography and bond strengths of feldspathic porcelain prepared using various sandblasting pressures.

Science.gov (United States)

Moravej-Salehi, Elham; Moravej-Salehi, Elahe; Valian, Azam

2016-11-01

The purpose of this study was to determine the bond strength of composite resin to feldspathic porcelain and its surface topography after sandblasting at different pressures. In this in vitro study, 68 porcelain disks were fabricated and randomly divided into four groups of 17. The porcelain surface in group 1 was etched with hydrofluoric acid. Groups 2, 3, and 4 were sandblasted at 2, 3 and 4 bars pressure, respectively. Surface topography of seven samples in each of the four groups was examined by a scanning electron microscope (SEM). The remaining 40 samples received the same silane agent, bonding agent, and composite resin and they were then subjected to 5000 thermal cycles and evaluated for shear bond strength. Data were analyzed using one-way anova. The mode of failure was determined using stereomicroscope and SEM. The highest shear bond strength was seen in group 4. however, statistically significant differences were not seen between the groups (P = 0.780). The most common mode of failure was cohesive in porcelain. The SEM showed different patterns of hydrofluoric acid etching and sandblasting. Increasing the sandblasting pressure increased the surface roughness of feldspathic porcelain but no difference in bond strength occurred. © 2015 Wiley Publishing Asia Pty Ltd.

Study of the adherence between polymer-modified mortars and porcelain stoneware tiles

Directory of Open Access Journals (Sweden)

Alessandra Etuko Feuzicana de Souza Almeida

2005-09-01

Full Text Available Despite the excellent characteristics of porcelain tiles, their application on building facades requires special attention, since this material differs from conventional ceramics and because facades are exposed to weathering that can damage ceramic revetments. The combination of polymer and silica fume to produce mortars results in excellent properties, which are ideal for repairs and revetments requiring high performance. Such improvements justify its study for the installation of porcelain tiles. This article presents bond strength results for mortars containing different amounts of polymer and silica indicating the applicability of these mortars as a construction material. To complement this study, the interface between the porcelain and the mortars was analyzed by scanning electron microscopy (SEM.

Identification and Characterization of Wor4, a New Transcriptional Regulator of White-Opaque Switching

Directory of Open Access Journals (Sweden)

Matthew B. Lohse

2016-03-01

Full Text Available The human fungal pathogen Candida albicans can switch between two cell types, “white” and “opaque,” each of which is heritable through many cell divisions. Switching between these two cell types is regulated by six transcriptional regulators that form a highly interconnected circuit with multiple feedback loops. Here, we identify a seventh regulator of white-opaque switching, which we have named Wor4. We show that ectopic expression of Wor4 is sufficient to drive switching from the white to the opaque cell type, and that deletion of Wor4 blocks switching from the white to the opaque cell type. A combination of ectopic expression and deletion experiments indicates that Wor4 is positioned upstream of Wor1, and that it is formally an activator of the opaque cell type. The combination of ectopic expression and deletion phenotypes for Wor4 is unique; none of the other six white-opaque regulators show this pattern. We determined the pattern of Wor4 binding across the genome by ChIP-seq and found it is highly correlated with that of Wor1 and Wor2, indicating that Wor4 is tightly integrated into the existing white-opaque regulatory circuit. We previously proposed that white-to-opaque switching relies on the activation of a complex circuit of feedback loops that remains excited through many cell divisions. The identification of a new, central regulator of white-opaque switching supports this idea by indicating that the white-opaque switching mechanism is considerably more complex than those controlling conventional, nonheritable patterns of gene expression.

7 CFR 160.14 - Opaque rosin.

Science.gov (United States)

2010-01-01

... Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) NAVAL STORES REGULATIONS AND... resulting when rosin undergoes internal modification indicated by a turbid, clouded, or opaque appearance...

Some new results of PIXE study on Chinese ancient porcelain

Science.gov (United States)

Cheng, H. S.; Zhang, B.; Zhu, D.; Yang, F. J.; Sun, X. M.; Guo, M. S.

2005-10-01

This paper reports some new results obtained by PIXE on Chinese ancient porcelain. The first results concern the provenance of blue and white porcelain made during the Tang Dynasty (AD618-907), which are the earliest products found in China. The PIXE experimental results show that they were fired in Huangye Kiln, Gongyi, Henan Province. The chemical composition of the body, white glaze and of the cobalt pigment will be reported. This paper also reports the results for early Chinese blue and white porcelain made under the Yuan dynasty (AD1206-1368) in Jingdezhen, Jiangxi Province. Experimental results show that the chemical composition of the cobalt pigment used by officers and popular are similar. These materials were imported from another country. The local asbolite was used as cobalt pigment material since the early Ming Dynasty (AD1368-1644) in Jingdezhen at folk kiln, and it was used at official kiln until the 16th century.

Some new results of PIXE study on Chinese ancient porcelain

Energy Technology Data Exchange (ETDEWEB)

Cheng, H.S. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China)]. E-mail: hscheng@fudan.edu.cn; Zhang, B. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China); Zhu, D. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China); Yang, F.J. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China); Sun, X.M. [Cultural Relics and Archaeology Research Institute of Henan Province, Zheng Zhou 450000 (China); Guo, M.S. [Cultural Relics and Archaeology Research Institute of Henan Province, Zheng Zhou 450000 (China)

2005-10-15

This paper reports some new results obtained by PIXE on Chinese ancient porcelain. The first results concern the provenance of blue and white porcelain made during the Tang Dynasty (AD618-907), which are the earliest products found in China. The PIXE experimental results show that they were fired in Huangye Kiln, Gongyi, Henan Province. The chemical composition of the body, white glaze and of the cobalt pigment will be reported. This paper also reports the results for early Chinese blue and white porcelain made under the Yuan dynasty (AD1206-1368) in Jingdezhen, Jiangxi Province. Experimental results show that the chemical composition of the cobalt pigment used by officers and popular are similar. These materials were imported from another country. The local asbolite was used as cobalt pigment material since the early Ming Dynasty (AD1368-1644) in Jingdezhen at folk kiln, and it was used at official kiln until the 16th century.

Some new results of PIXE study on Chinese ancient porcelain

International Nuclear Information System (INIS)

Cheng, H.S.; Zhang, B.; Zhu, D.; Yang, F.J.; Sun, X.M.; Guo, M.S.

2005-01-01

This paper reports some new results obtained by PIXE on Chinese ancient porcelain. The first results concern the provenance of blue and white porcelain made during the Tang Dynasty (AD618-907), which are the earliest products found in China. The PIXE experimental results show that they were fired in Huangye Kiln, Gongyi, Henan Province. The chemical composition of the body, white glaze and of the cobalt pigment will be reported. This paper also reports the results for early Chinese blue and white porcelain made under the Yuan dynasty (AD1206-1368) in Jingdezhen, Jiangxi Province. Experimental results show that the chemical composition of the cobalt pigment used by officers and popular are similar. These materials were imported from another country. The local asbolite was used as cobalt pigment material since the early Ming Dynasty (AD1368-1644) in Jingdezhen at folk kiln, and it was used at official kiln until the 16th century

Distinguish of Famous Jun Porcelain in Ancient and Present Age by INAA and BP Neural Network

International Nuclear Information System (INIS)

Li Guoxia; Liang Xianhua; Zhao Weijuan; Sun Hongwei; Guo Min; Xie Jianzhong; Gao Zhengyao; Cui Pengfei; Yang Dawei; Li rongwu; Zhao Qingyun; Sun Xinmin; Zhao Wenjun; Feng Songlin

2010-01-01

Forty samples of Jun porcelain from an ancient Juntai kiln and 3 modern Jun kilns (Kongjia, Miaojia and Xinghang) were selected and analyzed for 25 elements by INAA.The data were trained and forecasted by BP neural network. The results indicate that the network can distinguish unknown body and glaze samples of the official Jun porcelain and the modern top-grade Jun porcelain after proper training. (authors)

Analysis of ancient fine white porcelains by SRXRF and preliminary study of the discriminating criteria

International Nuclear Information System (INIS)

Feng Xiangqian; Feng Songlin; Xu Qing; Zhang Ying; Lei Yong; Fan Dongyu; Cheng Lin; Huang Yuying; He Wei

2002-01-01

30 Samples were chosen from the fine white porcelain shards excavated in Xing, Xing and Jingxing kilns of Hebei province. Their bodies and glaze were analyzed for 19 elements by SRXRF, followed by the cluster analysis and principal factor analysis. The statistical results show that porcelains of each kiln are classified as one class according to their elemental composition. It indicates that provenance of the fine white porcelains may be identified based on their chemical components

Greyish shadow on the labial gingival margin after insertion porcelain fused to metal crown on anterior teeth

Directory of Open Access Journals (Sweden)

Ike Damayanti Habar

2016-06-01

Full Text Available The crown is the type of restoration that replaces lost tooth structure caused by caries, trauma, or other causes which aims to restore comfort, function and patient confidence. Porcelain fused to metal restorationis an option that dominate the aesthetic restoration crown sand fixed prosthesisover the last 50 years. Porcelain fused to metal crown, consists of porcelain layer bonded to a thin cast metal coping that fits over the tooth preparation. Such a restoration combines the strength  and accurate fit of a cast metal crown with  the cosmetic effect of a porcelain crown. In some cases, it looks greyish shadow on the labial gingival margin after insertion porcelain fused to metal crowns on anterior teeth that can not be hidden even if the placement of the edge in subgingival. The purpose of this case report is to determine the cause of a greyish shadow on the labial gingival margin after insertion porcelain fused to metal crowns on anterior teeth and how to prevent a greyish shadow very disturbing aesthetics of the patient.

Opaque cloud detection

Science.gov (United States)

Roskovensky, John K [Albuquerque, NM

2009-01-20

A method of detecting clouds in a digital image comprising, for an area of the digital image, determining a reflectance value in at least three discrete electromagnetic spectrum bands, computing a first ratio of one reflectance value minus another reflectance value and the same two values added together, computing a second ratio of one reflectance value and another reflectance value, choosing one of the reflectance values, and concluding that an opaque cloud exists in the area if the results of each of the two computing steps and the choosing step fall within three corresponding predetermined ranges.

Art expertise and attribution of museum porcelain and faience

Directory of Open Access Journals (Sweden)

Revenok N.N.

2017-06-01

Full Text Available the article considers problems of research of museum art porcelain and faience of the XIX – the beginning of the XX century in the process of carrying out fine art expertise and also reveals the main criteria of Museum attribution. An important part of the examination methodology of thin-ceramic products is the development of special methods for their study in the conditions of modern laboratories on the latest-generation devices. The results presented in the article can contribute to the practical application of the proposed methods in conducting art criticism of art porcelain and faience in the museum research and restoration work.

Thermoluminescence and X-ray diffraction studies on sliced ancient porcelain samples

International Nuclear Information System (INIS)

Leung, P.L.; Yang, B.

1999-01-01

The thermal activation characteristics (TACs) of the sensitivity of the '110 deg. C' peak in 14 sliced ancient Chinese porcelain samples are studied. Comparing with the TACs of natural quartz and synthetic mullite, the relation between the TACs and the composition of the sample is discussed with reference to the X-ray diffraction (XRD) spectra. It is suggested that in some cases, contribution of the porcelain components other than quartz to the TACs is not negligible

Thermoluminescence and X-ray diffraction studies on sliced ancient porcelain samples

Energy Technology Data Exchange (ETDEWEB)

Leung, P.L.; Yang, B. E-mail: yangbr@bnu.edu.cn

1999-09-01

The thermal activation characteristics (TACs) of the sensitivity of the '110 deg. C' peak in 14 sliced ancient Chinese porcelain samples are studied. Comparing with the TACs of natural quartz and synthetic mullite, the relation between the TACs and the composition of the sample is discussed with reference to the X-ray diffraction (XRD) spectra. It is suggested that in some cases, contribution of the porcelain components other than quartz to the TACs is not negligible.

Thermoluminescence and X-ray diffraction studies on sliced ancient porcelain samples

Science.gov (United States)

Leung, P. L.; Yang, B.

1999-09-01

The thermal activation characteristics (TACs) of the sensitivity of the '110°C' peak in 14 sliced ancient Chinese porcelain samples are studied. Comparing with the TACs of natural quartz and synthetic mullite, the relation between the TACs and the composition of the sample is discussed with reference to the X-ray diffraction (XRD) spectra. It is suggested that in some cases, contribution of the porcelain components other than quartz to the TACs is not negligible.

White cells facilitate opposite- and same-sex mating of opaque cells in Candida albicans.

Directory of Open Access Journals (Sweden)

Li Tao

2014-10-01

Full Text Available Modes of sexual reproduction in eukaryotic organisms are extremely diverse. The human fungal pathogen Candida albicans undergoes a phenotypic switch from the white to the opaque phase in order to become mating-competent. In this study, we report that functionally- and morphologically-differentiated white and opaque cells show a coordinated behavior during mating. Although white cells are mating-incompetent, they can produce sexual pheromones when treated with pheromones of the opposite mating type or by physically interacting with opaque cells of the opposite mating type. In a co-culture system, pheromones released by white cells induce opaque cells to form mating projections, and facilitate both opposite- and same-sex mating of opaque cells. Deletion of genes encoding the pheromone precursor proteins and inactivation of the pheromone response signaling pathway (Ste2-MAPK-Cph1 impair the promoting role of white cells (MTLa in the sexual mating of opaque cells. White and opaque cells communicate via a paracrine pheromone signaling system, creating an environment conducive to sexual mating. This coordination between the two different cell types may be a trade-off strategy between sexual and asexual lifestyles in C. albicans.

[Differential study of the bonding characterization of dental porcelain to Ni-Cr alloys].

Science.gov (United States)

Wei, Fang; Zhan, De-song; Wang, Yan-yan

2008-10-01

To study the bonding capability when Ni-Cr porcelain alloy was added with Ti, compound rare earth metals and removed the element of Be. Ni-Cr-Ti porcelain alloys manufactured by Institute of Metal Research of Chinese Academy of Sciences were tested. The test alloys were divided into three groups according to whether containing Be and compound rare earth metals or not. And HI BOND Ni-Cr base-metal alloy was chosen as control. The metal-ceramic specimens were prepared for shear test, scanning electron microscope (SEM) and energy spectrum analysis. The shear bond strength of the four groups were analyzed. No significant difference were observed among them (P > 0.05). No crackle was found and they were contacted tightly between the porcelain and metal. The composition and contents of the four groups' interfaces were closed. The shear bond strength of the self-made Ni-Cr-Ti porcelain alloys all can satisfy the clinical requirements. Experimental groups containing Ti, compound rare earth metals and removing the element of Be can be used as better recommendation for clinical practice.

Study on the elemental features of ancient Chinese white porcelain at Jingdezhen by INAA

International Nuclear Information System (INIS)

Xie Guoxi; Feng Songlin; Feng Xiangqian; Li Yongqiang; Han Hongye; Wang Yanqing; Zhu Jihao; Yan Lingtong; Li Li

2009-01-01

Shards of ancient Chinese white porcelain, which were excavated at Maojiawan in the city of Beijing, were analyzed by instrumental neutron activation analysis (INAA). These shards were fired in the period between the Yuan (AD 1271-1368) and Ming (AD 1368-1644) dynasties at Jingdezhen in southern China. According to the analytical results, different raw materials were used for making porcelain body in this period. Fe and Na are the characteristic elements which can be used for identifying the specific date of these porcelains. Furthermore, shards of Hongwu era (AD 1368-1398), Yongle-Xuande era (AD 1403-1435) and Chenghua-Zhengde era (AD 1465-1561) of the Ming dynasty can be clearly distinguished by their elemental body composition. The temporal chemical variation in the porcelain body of these eras is observed. The elemental body composition of Zhengde-Tianshun era (AD 1436-1464) is mainly similar to that of the Hongwu and Yongle-Xuande eras. The temporal chemical feature of Zhengtong-Tianshun era was not found.

Study on the elemental features of ancient Chinese white porcelain at Jingdezhen by INAA

Energy Technology Data Exchange (ETDEWEB)

Xie Guoxi [Institute of High Energy Physics, Chinese Academy of Sciences, 19 Yu Quan Lu, Beijing 100049 (China); Graduated University of Chinese Academy of Sciences, Beijing 100049 (China); Feng Songlin [Institute of High Energy Physics, Chinese Academy of Sciences, 19 Yu Quan Lu, Beijing 100049 (China)], E-mail: fengsl@ihep.ac.cn; Feng Xiangqian [Institute of High Energy Physics, Chinese Academy of Sciences, 19 Yu Quan Lu, Beijing 100049 (China); Li Yongqiang; Han Hongye [Beijing Institute of Cultural Relics, Beijing 100009 (China); Wang Yanqing; Zhu Jihao; Yan Lingtong; Li Li [Institute of High Energy Physics, Chinese Academy of Sciences, 19 Yu Quan Lu, Beijing 100049 (China)

2009-03-15

Shards of ancient Chinese white porcelain, which were excavated at Maojiawan in the city of Beijing, were analyzed by instrumental neutron activation analysis (INAA). These shards were fired in the period between the Yuan (AD 1271-1368) and Ming (AD 1368-1644) dynasties at Jingdezhen in southern China. According to the analytical results, different raw materials were used for making porcelain body in this period. Fe and Na are the characteristic elements which can be used for identifying the specific date of these porcelains. Furthermore, shards of Hongwu era (AD 1368-1398), Yongle-Xuande era (AD 1403-1435) and Chenghua-Zhengde era (AD 1465-1561) of the Ming dynasty can be clearly distinguished by their elemental body composition. The temporal chemical variation in the porcelain body of these eras is observed. The elemental body composition of Zhengde-Tianshun era (AD 1436-1464) is mainly similar to that of the Hongwu and Yongle-Xuande eras. The temporal chemical feature of Zhengtong-Tianshun era was not found.

Study on the elemental features of ancient Chinese white porcelain at Jingdezhen by INAA

Science.gov (United States)

Xie, Guoxi; Feng, Songlin; Feng, Xiangqian; Li, Yongqiang; Han, Hongye; Wang, Yanqing; Zhu, Jihao; Yan, Lingtong; Li, Li

2009-03-01

Shards of ancient Chinese white porcelain, which were excavated at Maojiawan in the city of Beijing, were analyzed by instrumental neutron activation analysis (INAA). These shards were fired in the period between the Yuan (AD 1271-1368) and Ming (AD 1368-1644) dynasties at Jingdezhen in southern China. According to the analytical results, different raw materials were used for making porcelain body in this period. Fe and Na are the characteristic elements which can be used for identifying the specific date of these porcelains. Furthermore, shards of Hongwu era (AD 1368-1398), Yongle-Xuande era (AD 1403-1435) and Chenghua-Zhengde era (AD 1465-1561) of the Ming dynasty can be clearly distinguished by their elemental body composition. The temporal chemical variation in the porcelain body of these eras is observed. The elemental body composition of Zhengde-Tianshun era (AD 1436-1464) is mainly similar to that of the Hongwu and Yongle-Xuande eras. The temporal chemical feature of Zhengtong-Tianshun era was not found.

Deletion mutagenesis identifies a haploinsufficient role for gamma-zein in opaque-2 endosperm modification

Science.gov (United States)

Quality Protein Maize (QPM) is a hard kernel variant of the high-lysine mutant, opaque-2. Using gamma irradiation, we created opaque QPM variants to identify opaque-2 modifier genes and to investigate deletion mutagenesis combined with Illumina sequencing as a maize functional genomics tool. A K0326...

Effects of surface treatments on bond strength of dental Ti-20Cr and Ti-10Zr alloys to porcelain

International Nuclear Information System (INIS)

Lin, Hsi-Chen; Wu, Shih-Ching; Ho, Wen-Fu; Huang, Ling-Hsiu; Hsu, Hsueh-Chuan

2010-01-01

The purpose of this study was to investigate the effect of surface treatments, including sandblasting and grinding, on the bond strength between a low-fusing porcelain and c.p. Ti, Ti-20Cr and Ti-10Zr alloys. The surface treatments were divided into 2 groups. Grinding surface treatment was applied to the first group, which served as the control, and sandblasting was applied to the second group. After treatment, low-fusing porcelain (Titankeramik) was fired onto the surface of the specimens. A universal testing machine was used to perform a 3-point bending test. The metal-ceramic interfaces were subjected to scanning electron microscopic analysis. Of the sandblasted samples, the debonding test showed that Ti-20Cr alloy had the strongest (31.50 MPa) titanium-ceramic bond (p < 005), followed by c.p. Ti (29.4 MPa) and Ti-10Zr (24.3 MPa). Of the grinded samples, Ti-20Cr alloy showed 27.3 MPa titanium-ceramic bond (p < 005), followed by c.p. Ti (14.3 MPa) and Ti-10Zr (failure). The SEM micrographs of the metal surface after debonding showed residual porcelain retained on all samples. On the whole, sandblasting surface treatment appears to have had a more beneficial effect on the Ti-ceramic bond strength than grinding surface treatment. Furthermore, surface treatment of Ti-20Cr with either grinding or sandblasting resulted in adequate bond strength, which exceeded the lower limit value in the ISO 9693 standard (25 MPa).

Influence of thermo-mechanical cycling on porcelain bonding to cobalt-chromium and titanium dental alloys fabricated by casting, milling, and selective laser melting.

Science.gov (United States)

Antanasova, Maja; Kocjan, Andraž; Kovač, Janez; Žužek, Borut; Jevnikar, Peter

2018-04-01

The aim has been to determine the effect of thermo-mechanical cycling on shear-bond-strength (SBS) of dental porcelain to Co-Cr and Ti-based alloys fabricated by casting, computer-numerical-controlled milling, and selective-laser-melting (SLM). Seven groups (n=22/group) of metal cylinders were fabricated by casting (Co-Cr and commercially pure-cpTi), milling (Co-Cr, cpTi, Ti-6Al-4V) or by SLM (Co-Cr and Ti-6Al-4V) and abraded with airborne-particles. The average surface roughness (R a ) was determined for each group. Dental porcelain was applied and each metal-ceramic combination was divided into two subgroups - stored in deionized water (24-h, 37°C), or subjected to both thermal (6000-cycles, between 5 and 60°C) and mechanical cycling (10 5 -cycles, 60N-load). SBS test-values and failure modes were recorded. Metal-ceramic interfaces were analyzed with a focused-ion-beam/scanning-electron-microscope (FIB/SEM) and energy-dispersive-spectroscopy (EDS). The elastic properties of the respective metal and ceramic materials were evaluated by instrumented-indentation-testing. The oxide thickness on intact Ti-based substrates was measured with Auger-electron-spectroscopy (AES). Data were analyzed using ANOVA, Tukey's HSD and t-tests (α=0.05). The SBS-means differed according to the metal-ceramic combination (p<0.0005) and to the fatigue conditions (p<0.0005). The failure modes and interface analyses suggest better porcelain adherence to Co-Cr than to Ti-based alloys. Values of R a were dependent on the metal substrate (p<0.0005). Ti-based substrates were not covered with thick oxide layers following digital fabrication. Ti-based alloys are more susceptible than Co-Cr to reduction of porcelain bond strength following thermo-mechanical cycling. The porcelain bond strength to Ti-based alloys is affected by the applied metal processing technology. Copyright © 2017 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Utilization of radiometric method in evaluation of wear on human dental enamel in vitro by dental porcelain glazed and polished

International Nuclear Information System (INIS)

Adachi, Lena Katekawa; Campos, Tomie Nakakuki de; Adachi, Eduardo Makoto

2005-01-01

The dental porcelain is a material commonly used in prosthesis. Disadvantages of dental porcelain use include possibility to cause tooth or dental materials wear. Before its use in the mouth, surfaces are treated with polishing and/or glazing. This research used the radiometric method to verify the influence of these surface treatments on the porcelains of commercial brands: Ceramco II, Noritake and Finesse. This method was originally developed for dentifrice abrasiveness evaluation. Five specimens of dental enamel and 10 specimens of each porcelain (5 glazed, 5 polished) were used. The dental enamel was flattened and irradiated with neutrons from the IEA-R1 (IPEN/CNEN) nuclear reactor. Then it was weared by each porcelain in sliding motion, with water. After 2,500 cycles for each porcelain specimen, the released enamel residue was measured. The enamel wear was evaluated by measuring beta activity of 32 P transferred to water from the irradiated tooth. Results varied from 2.57 to 5.81 μg of enamel /mm 2 weared surface. There was no statistical difference (α=0.05) between dental enamel wear caused by the same porcelains glazed or polished. The results suggest that adequate surface finishing depend on the type of dental porcelain. (author)

[Effect of Ti bonder on the bond strength between porcelain and titanium].

Science.gov (United States)

Yao, Hai; Luo, Xiao-ping

2009-12-01

To investigate the influence of GC Initial Ti Bonder on bond strength between Vita Titankeramik porcelain and titanium. Forty titanium samples were prepared and randomly assigned to 4 groups with 10 samples in each group. Samples in each group were subjected to one of the following surface treatments, burnishing (Group B), sandblasting (Group S), firing GC Initial Ti Bonder after burnishing (Group BG) and firing GC Initial Ti Bonder after sandblasting (Group SG). Vita Titankeramik porcelain were fired on the surface of each sample in the middle. Three-point bending tests were conducted on each sample according to the ISO 9693. The fracture patterns of all specimens were recorded using zoom stereo microscope (ZSM) and the fracture surfaces were observed under scanning electron microscope (SEM). With fired GC Initial Ti Bonder, the bond strength of Vita Titankeramik porcelain to titanium in Group BG and Group SG were (32.72 +/- 4.46) and (34.25 +/- 6.52) MPa respectively, which reach the ISO 9693 standard for clinical use and were significantly higher than those in Group B [(20.70 +/- 3.15) MPa] and Group S [(23.92 +/- 5.02) MPa]. GC Initial Ti Bonder can significantly improve bond strength between Vita Titankeramik porcelain and titanium.

Genetic analysis of vitreous endosperms derived from homozygotic plants for opaque-2 gene in maize (Zea mays L.)

International Nuclear Information System (INIS)

Prioli, A.J.; Barbosa, H.M.; Sant'Anna, R.

1980-01-01

From experiments in which opaque-2 maize seeds were treated with gamma rays and ethil methanesulfonate, and their respective untreated controls, seeds with hard, vitreous endosperms were obtained. Some of these were completely vitreous, with no evidence of opaque endosperm tissue. Others had very small and few (one to three) areas of opaque tissue. Plants derived from completely vitreous endosperm seeds were self pollinated and crossed to an opaque-2 inbred. The segregation of vitreous to opaque seeds indicated that the normal allele at the opaque-2 locus was responsible for the vitreousity of the endosperm. Lysine content of the vitreous endosperm was comparable to that of normal endosperms. Plants derived from vitreous seeds with few and tiny spots of opaque tissue produced, upon selfing or crossing to the opaque-2 inbred, only opaque-2 seeds. It is concluded that: (a) induced mutation may not be an effective tool to obtain vitreous opaque-2 endosperm with high lysine content; and, (b) there are unknown genetic systems which severely modify the expression of the opaque-2 gene. (Author) [pt

Measurement of transient thickness between the body and glaze layers of ancient porcelains using microprobe EDXRF technique

International Nuclear Information System (INIS)

Peng Zicheng

2004-01-01

The oxide contents of TiO 2 , MnO, SrO and Fe 2 O 3 in the body and glaze layers of the Jiao-Tan-Xia (JTX) and Lao-Hu-Dong (LHD) porcelains in Southern Song Dynasty (1127-1279 A.D.) have been determined using an International Eagle-II μ-probe EDXRF spectrometer. The results show that the contents in the body are much different from those in the glaze one. Therefore, the transient thickness (TT) between the body and glaze layers can be measured through determination of a distance of the drift change in the chemical contents. The TT average for the JTX porcelains is 161 μm, while that for the LHD porcelains is 258 μm, which are consistent with a range of 0.15-0.3 mm in the Ru-Yao porcelains. The different TT is related to the variances in firing temperature and raw material for manufacturing the respective porcelains. (authors)

Radio opaque gloves

International Nuclear Information System (INIS)

Whittaker, A.V.; Whittaker, R.E. Jr.; Goldstrom, R.A.; Shipko, F.J.

1975-01-01

Radiation shielding garments and accessories, such as radio-opaque gloves for surgeons, shielding against the harmful x-ray radiation in a fluoroscopic zone, are advantageously different from garments for shielding from other medical uses of x-rays. Such garments are provided with zones of differing opacity, whereby desired sensitivity and ''feel'' through the glove material is retained. One feature is the provision of an ''opacity gradient'' across the glove cross section with opacity being relatively low at the fingertip area (lesser shield-thickness), but relatively high at the less nonprehensile hand zones, such as the palm. Glove fabrication techniques for achieving such an opacity gradient are described. (U.S.)

Study on provenance of ancient Yaozhou porcelain bodies by fingerprint elements scatter analysis

International Nuclear Information System (INIS)

Zhao Weijuan; Guo Min; Gao Zhengyao; Li Guoxia; Xie Jianzhong

2004-01-01

25 samples of Yaozhou porcelain bodies, 3 samples of the tri-color pottery bodies during the Tang Dynasty, 1 samples of Saggar material during Song Dynasty and 4 samples of clay mineral taken from the place near Yaozhou Kiln Museum was selected. The technique of neutron activation analysis (NAA) has been employed to measure the content of 29 kinds of elements in the samples. 8 elements of them were selected as fingerprint elements to make scatter analysis. The conclusion is that the ancient Yaozhou porcelain bodies produced by different kilns have long shared a stable and concentrated raw material sources. Both the tri-colored pottery bodies made in Yaozhou Kilns during the Tang Dynasty and the Yaozhou porcelain bodies are from the same provenance. (authors)

78 FR 37571 - Certain Opaque Polymers; Institution of Investigation Pursuant to United States Code

Science.gov (United States)

2013-06-21

... INTERNATIONAL TRADE COMMISSION [Inv. No. 337-TA-883] Certain Opaque Polymers; Institution of... importation of certain opaque polymers by reason of infringement of certain claims of U.S. Patent No. 6,020... certain opaque polymers that infringe one or more of claims 1-5 of the '435 patent, claims 1 and 3-7 of...

An optically stimulated luminescence study of porcelain related to radiation dosimetry

DEFF Research Database (Denmark)

Poolton, N.R.J.; Bøtter-Jensen, L.; Jungner, H.

1995-01-01

Stokes and anti-Stokes shifted in energy. Glazing is shown in some cases to be considerably more sensitive as a radiation dosemeter than the main porcelain ceramic. By comparison with the properties of artifical phosphors, the principal luminescent matrix is identified as being Al2O3......This article describes the essential features regarding the photo-stimulated luminescence of porcelain: both the main ceramic and glazing materials are studied. In each case, radiation dose dependent signals are observed, superimposed on dose independent luminescence transitions that are both...

Moessbauer studies on ancient Jizhon plain Temmoku porcelains

International Nuclear Information System (INIS)

Yu Zhengfang; Zheng Yufang; Lin Yongqiang

1994-01-01

Three kinds of ancient Jizhou plain Temmoku wares and their several ware-making raw materials were studied by means of X-ray diffraction (XRD) and Moessbauer spectroscopy. The firing technique of ancient Jizhou Temmoku porcelains is discussed. (orig.)

Study on distinguishing of Chinese ancient porcelains by neutron activation and fuzzy cluster analysis

International Nuclear Information System (INIS)

Wang An

1992-01-01

By means of the method of neutron activation, the contents of trace elements in some samples of Chinese ancient porcelains from different places of production were determined. The data were analysed by fuzzy cluster analysis. On the basis of the above mentioned works, a method with regard to the distinguishing and determining of Chinese ancient porcelain was suggested

Reuse of solid petroleum waste in the manufacture of porcelain stoneware tile.

Science.gov (United States)

Pinheiro, B C A; Holanda, J N F

2013-03-30

This study investigates the incorporation of solid petroleum waste as raw material into a porcelain stoneware tile body, in replacement to natural kaolin material by up to 5 wt.%. Tile formulations containing solid petroleum waste were pressed and fired at 1240 °C by using a fast-firing cycle. The tile pieces were tested to determine their properties (linear shrinkage, water absorption, apparent density, and flexural strength), sintered microstructure, and leaching toxicity. The results therefore indicated that the growing addition of solid petroleum waste into tile formulations leads to a decrease of linear shrinkage, apparent density, and flexural strength, and to an increase of water absorption of the produced tile materials. It was also found that the replacement of kaolin with solid petroleum waste, in the range up to 2.5 wt.%, allows the production of porcelain stoneware tile (group BIa, ISO 13006 standard). All concentrations of Ag, As, Ba, Cd, Cr (total), Hg, and Pb of the fired porcelain stoneware tile pieces in the leachate comply with the current regulatory limits. These results indicate that the solid petroleum waste could be used for high-quality porcelain stoneware tile production, thus giving rise to a new possibility for an environmentally friendly management of this abundant waste. Copyright © 2013 Elsevier Ltd. All rights reserved.

Influence of ultraviolet irradiation treatment on porcelain bond strength of titanium surfaces.

Science.gov (United States)

Kumasaka, Tomonari; Ohno, Akinori; Hori, Norio; Hoshi, Noriyuki; Maruo, Katsuichiro; Kuwabara, Atsushi; Seimiya, Kazuhide; Toyoda, Minoru; Kimoto, Katsuhiko

2018-01-26

To determine the effect of titanium (Ti) surface modification by ultraviolet irradiation (UVI) on the bond strength between Ti and porcelain. Grade 2 Ti plates were allotted to five groups: sandblasted (SA), 15 min UVI (UV), SA+5 min UVI (SA+UV5), SA+10 min UVI (SA+UV10), and SA+15 min UVI (SA+UV15). After surface treatment, porcelain was added. A precious metal (MC) was used for comparison with Ti. The effects of 24-h storage at room temperature versus thermal cycling only at 5 and 55°C in water were evaluated. Subsequently, the tensile strength of each sample was tested. Data were analyzed using one-way analysis of variance and the Tukey test. In both the room temperature and thermal cycling groups, the MC and SA+15 min UVI samples showed significantly greater bond strengths than the other samples (pbond strength between porcelain and the Ti surface.

PROTECTIVE TREATMENTS FOR LAPPED PORCELAIN STONEWARE TILES AND EVALUATION OF THEIR CLEANABILITY

Directory of Open Access Journals (Sweden)

Elisa Rambaldi

2017-09-01

Full Text Available Since the arrival of lapped porcelain stoneware tiles on the market, several studies have been focused on the improvement of the technical characteristics of the surfaces of these products. Surface lapping induces aesthetical improvements, but can at the same time deteriorate the performance of porcelain stoneware tiles. To overcome this problem, it is possible to protect the lapped surface with commercial waterproofing materials. In this work, lapped commercial porcelain stoneware tiles with protective stain proofing agents (FILA PD15 and FILA 1239 Plus were evaluated. The stain resistance and chemical resistance results were correlated to the morphological surface characteristics of the products with and without protection. A systematic study of the surface porosity of the tiles was carried out. Results showed that unprotected surface pores tend to fill with dirt that is hardly removable by ordinary maintenance. If the pores are protected, the dirt from foot traffic is deposited only superficially and can be removed.

Study of provenance character on ancient porcelain of Yue Kiln at Silongkou with NAA

International Nuclear Information System (INIS)

Jihao Zhu; Songlin Feng; Dongyu Fan; Xiangqian Feng; Qing Xu; Yueming Shen; Zhenxi Zhuo; Wenjiang Zhang

2007-01-01

Chemical composition is an important information of studying the provenance character of ancient pottery and porcelain. The ancient celadon samples produced in Later Tang (850-907 A.D.) to Former Southern Song (1127-1279 A.D.) have been analyzed with NAA. Its provenance characteristic was compared with that of Hongzhou Kiln of Jiangxi Province and Yaozhou Kiln of Shanxi Province in this paper. The experimental data were studied with statistic methods. The results indicated that the chemical compositions of ancient porcelain body samples made in three kilns were different. The difference is able to be identified. The porcelain body materials of both Silongkou Yue Kiln and Hongzhou Kiln were similar. The samples of Yaozhou kiln in north of China existed obvious difference. (author)

Incorporation of feasibility study of residue thin kaolin in of porcelain formulations production

International Nuclear Information System (INIS)

Almeida, V.S. de; Ferreira, E.C.; Oliveira, T.M. de; Freitas, K.D. de Araujo; Soares Filho, J.E.; Sousa, F.J.P. de

2016-01-01

The porcelain is the more advanced product among traditional ceramics due to the high technology used in its manufacture and its excellent technological and aesthetic properties. Due to the continuing worldwide development, kaolin processing industries have increased their productivity and consequently generating large amounts of waste, contributing to environmental degradation. Studies are being conducted to analyze the incorporation of such wastes in the ceramic mass compositions. The objective of this study was to evaluate 4 formulations of porcelain as the possibility of using waste coming from the last stage of kaolin processing. Processing occurred by wet grinding process, with uniaxial compacting pressure of 45 MPa after heat treatment at 1250 ° C. Technological tests were carried out physical and mechanical product. The results showed that the addition of fine kaolin residue was presented as an efficient alternative for the porcelain industry. (author)

Effects of different surface treatments on the color stability of various dental porcelains

Directory of Open Access Journals (Sweden)

Isil Sarikaya

2011-06-01

Conclusions: Within the limitations of this study, the results suggest that feldspathic and low-fusing porcelain specimens were found to be more color-stable for glazed specimens versus polished specimens regardless of whether they were stained with the coffee solution. Glazed and polished specimens with different polishing materials demonstrated that the ΔE values were at an acceptable level for all of the porcelain materials tested (1 < ΔE < 3.7.

Ultrasonic characterization of defective porcelain tiles

Directory of Open Access Journals (Sweden)

Eren, E.

2012-08-01

Full Text Available The aim of this work is the optimization of ultrasonic methods in the non-destructive testing of sintered porcelain tiles containing defects. For this reason, a silicon nitride ball, carbon black and PMMA (Polymethylmethacrylate were imbedded in porcelain tile granules before pressing to make special defects in tiles. After sintering at 1220ºC, the time of flight of the ultrasonic waves and ultrasonic signal amplitudes through the sintered porcelain tiles were measured by a contact ultrasonic transducer operating on pulse-echo mode. This method can allow for defect detection using the A-scan. The results of the test showed that the amplitude of the received peak for a defective part is smaller than for a part which has no defects. Depending on the size, shape and position of the defect, its peak can be detected. Additionally, an immersion pulse-echo C-scan method was also used to differentiate between defects in porcelain tiles. By using this technique, it is possible to determine the place and shape of defects. To support the results of the ultrasonic investigation, a SEM characterization was also made.

El fin principal de este trabajo es la optimización de métodos ultrasónicos en la prueba no destructiva de azulejos sinterizados de porcelana que contienen defectos. Por lo tanto, bolas del nitruro de silicio, negros de carbón y PMMA (polimetilmetacrilato fueron encajados en gránulos del azulejo de porcelana antes de presionar para hacer defectos especiales en azulejos. Después de sinterizado en 1220ºC, el tiempo de vuelo de las ondas ultrasónicas fue medido a través del azulejo sinterizado de la porcelana. El tiempo del vuelo de ondas ultrasónicas fue medido por un transductor de contacto ultrasónico operando en modo eco-pulso. Este método puede permitir la detección de defectos usando escaneo-A. Los resultados de la prueba demostraron que la amplitud del pico recibido por partes defectuosas es más pequeño que la parte

Thermal activation and radiation quenching effects in pre-dose dating of porcelain

International Nuclear Information System (INIS)

Wang Weida; Xia Junding

2005-01-01

The pre-dose technique is very useful for thermoluminescence dating of porcelain. It incorporates two characteristics in the porcelain dating, i.e. thermal activation and radiation quenching. Two methods, activation method and quenching method, for evaluation of paleodose were introduced. The results show that activation method and quenching method one suitable for dating of lower limit age (less than 100 years B.P.) and upper limit age (greater than 1000 years B.P.), respectively. When both methods are co-used, the dating will be more accurate. (authors)

Microshear bond strength of composite resins to enamel and porcelain substrates utilizing unfilled versus filled resins.

Science.gov (United States)

Najafi-Abrandabadi, Ahmad; Najafi-Abrandabadi, Siamak; Ghasemi, Amir; Kotick, Philip G

2014-11-01

Failures such as marginal discoloration and composite chipping are still the problems of tooth-colored restorations on the substrate of enamel and porcelain, which some of these problems are consequently as a result of failures in the bonding layer. Using filled resin has been recently introduced to increase the bond strength of this layer. The aim of this study was to compare the microshear bond strength (μ-SBS) of composite resins to enamel incubated in periods of 24 h and 9 months and porcelain with unfilled resin and flowable composites (filled resin). In this in vitro study, two groups of 75 enamel samples with different storage times (24 h and 9 months) and a group of 75 porcelain samples were used. They were divided into 5 experimental groups of 15 samples in each. Composite cylinders in tygon tubes were bonded on the surface of acid-etched enamel and pretreated porcelain. Wave, Wave MV, Wave HV, Grandioflow and Margin Bond were used as bonding agents. The μ-SBS was measured at the speed of 1.0 mm/min. The bond strengths were analyzed with one-way analysis of variance (ANOVA) test followed by Tukey test. P composites (filled resins) can be used instead of unfilled resins in bonding composite resins to enamel and porcelain substrates.

Porcelain Product Quality Analysis in PT XYZ

Directory of Open Access Journals (Sweden)

Ho Hwi Chie

2015-12-01

Full Text Available PT. XYZ is a company engaged in manufacturing porcelain dinner ware such as plates, cups, teapot, bowl, etc Porcelain product is safe for use and product defect will only affect the aesthetic not the functional side. The company always maintain the quality of the products produced as by maintaining a good product, in terms of visuals, will keep customers interested in the product. Good quality products characterized by quality A / B and C, and the product defect characterized by the quality of D, Lost, and BU. Concepts and methods used to analyze is a statistical process control (SPC which includes Pareto diagram, fraction nonconformities, flow charts and fishbone diagrams and management tools (fault tree analysis. Statistical Process Control (SPC is one of the methods, which includes Pareto charts, fraction nonconformities, flow chart, and fishbone diagram and also management tools (fault tree analysis. SPC is useful to find the facts from the problems and factors that affect the quality of the products, while fault tree analysis is useful to analyze each of the production process.

Using glass-graded zirconia to increase delamination growth resistance in porcelain/zirconia dental structures.

Science.gov (United States)

Chai, Herzl; Mieleszko, Adam J; Chu, Stephen J; Zhang, Yu

2018-01-01

Porcelain fused to zirconia (PFZ) restorations are widely used in prosthetic dentistry. However, their tendency to delaminate along the P/Z interface remains a practical problem so that assessing and improving the interfacial strength are important design aspects. This work examines the effect of modifying the zirconia veneering surface with an in-house felspathic glass on the interfacial fracture resistance of fused P/Z. Three material systems are studied: porcelain fused to zirconia (control) and porcelain fused to glass-graded zirconia with and without the presence of a glass interlayer. The specimens were loaded in a four-point-bend fixture with the porcelain veneer in tension. The evolution of damage is followed with the aid of a video camera. The interfacial fracture energy G C was determined with the aid of a FEA, taking into account the stress shielding effects due to the presence of adjacent channel cracks. Similarly to a previous study on PFZ specimens, the fracture sequence consisted of unstable growth of channel cracks in the veneer followed by stable cracking along the P/Z interface. However, the value of GC for the graded zirconia was approximately 3 times that of the control zirconia, which is due to the good adhesion between porcelain and the glass network structure on the zirconia surface. Combined with its improved bonding to resin-based cements, increased resistance to surface damage and good esthetic quality, graded zirconia emerges as a viable material concept for dental restorations. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

indigenous manufacture and characterization of electrical porcelain

African Journals Online (AJOL)

Dr Obe

ohm cm, breakdown voltage of 26kV/mm, zero water absorption and dielectric constant between 9.2 and 10.8 within .... rising heat at a temperature of 1355 o. C and for ... thus the amount and composition of feldspar glass in the porcelain ... electrical measurements on the sample [4], ... 4.2 Experimental determination of the.

Bond strength and Raman analysis of the zirconia-feldspathic porcelain interface.

Science.gov (United States)

Ramos, Carla Müller; Cesar, Paulo Francisco; Lia Mondelli, Rafael Francisco; Tabata, Americo Sheitiro; de Souza Santos, Juliete; Sanches Borges, Ana Flávia

2014-10-01

Zirconia has the best mechanical properties of the available ceramic systems. However, the stability of the zirconia-feldspathic porcelain interface may be jeopardized by the presence of the chipping and debonding of the feldspathic porcelain. The purpose of this study is to evaluate the shear bond strength of 3 cold isostatic pressed zirconia materials and a feldspathic veneer by analyzing their interface with micro-Raman spectroscopy. The test groups were experimental zirconia, Zirkonzahn zirconia, and Schuetz zirconia. Blocks of partially sintered zirconia were cut into disks (n=20) and then veneered with a feldspathic porcelain. Half of the specimens from each group (n=10) were incubated in 37°C water for 24 hours, and the other half were thermocycled. All the specimens were then subjected to shear testing. The fractured areas were analyzed with optical stereomicroscopy and classified as adhesive, cohesive, or an adhesive-cohesive failure. Spectral patterns were examined to detect bands related to the zirconia and feldspathic porcelain phases. The shear strength data were submitted to 2-way ANOVA. No significant differences in shear bond strength were observed among the 3 groups, regardless of whether or not the specimens were thermocycled. Adhesive failures were the most prevalent types of failure (70%). Raman spectra were clearly distinguished for all the materials, which showed the presence of tetragonal and monoclinic phases. The controlled production of the experimental zirconia did not influence the results of the bond strength. Raman analysis suggested a process of interdiffusion by the presence of peaks associated with the zirconia and feldspathic ceramics. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

[Effects of magnetron sputtered ZrN on the bonding strength of titanium porcelain].

Science.gov (United States)

Zhou, Shu; Zhang, Wen-yan; Guang, Han-bing; Xia, Yang; Zhang, Fei-min

2009-04-01

To investigate the effect of magnetron sputtered ZrN on the bonding strength between a low-fusing porcelain (Ti/Vita titankeramik system) and commercially pure cast titanium. Sixteen specimens were randomly assigned to test group and control group (n=8). The control group received no surface treated. Magnetron sputtered ZrN film was deposited on the surface of specimens in the test group. Then the sixteen titanium-porcelain specimens were prepared in a rectangular shape and went through three-point bending test on a universal test machine. The bond strength of Ti/porcelain was recorded. The phase composition of the specimens was analyzed using X-ray diffraction (XRD). The interface at titanium and porcelain and the titanium surface after debonding were observed with a scanning electron microscopy (SEM) and analyzed using energy depressive spectrum (EDS). New phase of ZrN was found with XRD in the test group. Statistical analysis showed higher bond strength following ZrN surface treatment in the test group [(45.991+/-0.648) MPa] than that in the control group [(29.483+/-1.007) MPa] (P=0.000). Bonded ceramic could be observed in test group, the amount of bonded ceramic was more than that in the control group. No obvious bonded ceramic in control group was found. Magnetron sputtered ZrN can improve bond strength of Ti/Vita titankeramik system significantly.

Gingival-colored Porcelain: A Clinical Report of an Esthetic-prosthetic Paradigm.

Science.gov (United States)

Sonune, Shital Jalandar; Kumar, Shiv; Jadhav, Manish Shivaji; Martande, Santosh

2017-01-01

Traditionally, periodontics has been instrumental in treating hard- and soft-tissue defect. Surgical and regenerative periodontal procedures can reconstruct the three-dimensional architecture of the hard- and soft-tissue defect. However, at times, these invasive procedures leave the patients with an esthetic problem. In such situations, the defects can be treated by the prosthetic approach. A predictable esthetically pleasing and functional outcome without any surgical procedure is being a choice of treatment for many. This article discusses about the treatment for the defect of excessive hard and soft tissue, using porcelain fused to a metal restoration with gingival-colored porcelain for both tooth-supported and implant-supported fixed prosthesis.

Gingival-colored Porcelain: A Clinical Report of an Esthetic-prosthetic Paradigm

Science.gov (United States)

Sonune, Shital Jalandar; Kumar, Shiv; Jadhav, Manish Shivaji; Martande, Santosh

2017-01-01

Traditionally, periodontics has been instrumental in treating hard- and soft-tissue defect. Surgical and regenerative periodontal procedures can reconstruct the three-dimensional architecture of the hard- and soft-tissue defect. However, at times, these invasive procedures leave the patients with an esthetic problem. In such situations, the defects can be treated by the prosthetic approach. A predictable esthetically pleasing and functional outcome without any surgical procedure is being a choice of treatment for many. This article discusses about the treatment for the defect of excessive hard and soft tissue, using porcelain fused to a metal restoration with gingival-colored porcelain for both tooth-supported and implant-supported fixed prosthesis. PMID:29308371

The identification of Chenghua white and blue porcelain by using PIXE and multivariate statistical analysis

International Nuclear Information System (INIS)

Cheng Huansheng; Zhang Zhengquan; Yao Hua

2001-01-01

The major and minor chemical compositions of ancient white and blue porcelain made in Chenghua empire, Ming Dynasty and in Kangxi empire, Qing Dynasty have been determined by PIXE. Experimental results show that a real precious Chenghua white and blue porcelain made in Ming Dynasty at Kuan Kiln can be distinguished from the fakes made in Kangxi empire, Qing Dynasty

Chaetotaxy and setal diversity of grooming legs in species of porcelain crabs (Crustacea: Anomura: Porcellanidae

Directory of Open Access Journals (Sweden)

Luciane Augusto de Azevedo Ferreira

2018-03-01

Full Text Available Abstract The morphology of the fifth pereiopods was studied under scanning electron microscopy in ten species of porcelain crabs for chaetotaxy and setal diversity, namelly Megalobrachium pacificum, Megalobrachium roseum, Pachycheles grossimanus, Petrolisthes armatus, Petrolisthes tuberculatus, Pisidia brasiliensis, Pisidia longicornis, Polyonyx gibbesi, Porcellana platycheles and Porcellana sayana. Six setal types were identified: simple, pappose, sickle-shaped serrate, straight serrate, club-shaped and tooth-like cuspidate. Porcelain crabs can differ in the fifth pereiopod setal morphology, chaetotaxy and setal density, even among species within the same genus. The absence of sexual dimorphism of the grooming legs in porcelain crabs suggests that grooming eggs requires no particular grooming apparatus in females and that male and female are equal in grooming efficiency.

High-performance and anti-stain coating for porcelain stoneware tiles based on nanostructured zirconium compounds.

Science.gov (United States)

Ambrosi, Moira; Santoni, Sergio; Giorgi, Rodorico; Fratini, Emiliano; Toccafondi, Nicola; Baglioni, Piero

2014-10-15

The technological characteristics of porcelain stoneware tiles make them suitable for a wide range of applications spanning far beyond traditional uses. Due to the high density, porcelain stoneware tiles show high bending strength, wear resistance, surface hardness, and high fracture toughness. Nevertheless, despite being usually claimed as stain resistant, the surface porosity renders porcelain stoneware tiles vulnerable to dirt penetration with the formation of stains that can be very difficult to remove. In the present work, we report an innovative and versatile method to realize stain resistant porcelain stoneware tiles. The tile surface is treated by mixtures of nanosized zirconium hydroxide and nano- and micron-sized glass frits that thanks to the low particle dimension are able to penetrate inside the surface pores. The firing step leads to the formation of a glass matrix that can partially or totally close the surface porosity. As a result, the fired tiles become permanently stain resistant still preserving the original esthetical qualities of the original material. Treated tiles also show a remarkably enhanced hardness due to the inclusion of zirconium compounds in the glass coating. Copyright © 2014 Elsevier Inc. All rights reserved.

A method to measure internal contact angle in opaque systems by magnetic resonance imaging.

Science.gov (United States)

Zhu, Weiqin; Tian, Ye; Gao, Xuefeng; Jiang, Lei

2013-07-23

Internal contact angle is an important parameter for internal wettability characterization. However, due to the limitation of optical imaging, methods available for contact angle measurement are only suitable for transparent or open systems. For most of the practical situations that require contact angle measurement in opaque or enclosed systems, the traditional methods are not effective. Based upon the requirement, a method suitable for contact angle measurement in nontransparent systems is developed by employing MRI technology. In the Article, the method is demonstrated by measuring internal contact angles in opaque cylindrical tubes. It proves that the method also shows great feasibility in transparent situations and opaque capillary systems. By using the method, contact angle in opaque systems could be measured successfully, which is significant in understanding the wetting behaviors in nontransparent systems and calculating interfacial parameters in enclosed systems.

78 FR 31575 - Certain Opaque Polymers, Notice of Receipt of Complaint; Solicitation of Comments Relating to the...

Science.gov (United States)

2013-05-24

... INTERNATIONAL TRADE COMMISSION [Docket No 2957] Certain Opaque Polymers, Notice of Receipt of... received a complaint entitled Certain Opaque Polymers, DN 2957; the Commission is soliciting comments on... importation, and the sale within the United States after importation of certain opaque polymers. The complaint...

Efficient polymer solar cells on opaque substrates with a Laminated PEDOT : PSS top electrode

NARCIS (Netherlands)

Gupta, D.; Wienk, M.M.; Janssen, R.A.J.

2013-01-01

Solution processed polymer:fullerene solar cells on opaque substrates have been fabricated in conventional and inverted device configurations. Opaque substrates, such as insulated steel and metal covered glass, require a transparent conducting top electrode. We demonstrate that a high conducting

Thermoluminescence dating of chinese porcelain using a regression method of saturating exponential in pre-dose technique

International Nuclear Information System (INIS)

Wang Weida; Xia Junding; Zhou Zhixin; Leung, P.L.

2001-01-01

Thermoluminescence (TL) dating using a regression method of saturating exponential in pre-dose technique was described. 23 porcelain samples from past dynasties of China were dated by this method. The results show that the TL ages are in reasonable agreement with archaeological dates within a standard deviation of 27%. Such error can be accepted in porcelain dating

Dental Porcelain Furnaces: Test and Evaluation.

Science.gov (United States)

1988-01-01

D Q)L a ) a) C ) C C C C c *. . 3a)0. >4 a)->4 >4 -, Z 0 -a-’- 4-% a) ( nca )m m nU Cs C ) (3 ) 11) a) a) a3) Q) a) W) a2) C C~~ >4 L > > >1 >1 4 > 4...Fig. 1) is a computerized programmable porcelain furnace with 45 open programs. This unit has a large detachable cathode -ray tube (CRT) screen which

Anodization process produces opaque, reflective coatings on aluminum

Science.gov (United States)

1965-01-01

Opaque, reflective coatings are produced on aluminum articles by an anodizing process wherein the anodizing bath contains an aqueous dispersion of finely divided insoluble inorganic compounds. These particles appear as uniformly distributed occlusions in the anodic deposit on the aluminum.

Spontaneous CFS rhinorrhoea: role of computerized opaque cisternography; Rhinorrhee cerebro-spinale spontanee: place de la cisternographie opaque computerisee

Energy Technology Data Exchange (ETDEWEB)

Jouini, S.; Saidane, S.; Maamouri, M.; Shili, S.; Menif, E.; Ben Hajel, H.; El Khedim, A.; Ben Jaafar, M.; Belkahia, A. [Hopital La Rabtan Tunis (Tunisia)

1995-12-31

Spontaneous CSF rhinorrhoea, secondary to trauma in the great majority of cases, is very rare (3-4%). The authors report a case of spontaneous CSF rhinorrhoea secondary to an ethmoidal osteo-dural defect, diagnosed by digital cisternography and confirmed by the surgical operation. The value of digital opaque cisternography and its place in the diagnostic arsenal are discussed. (authors). 12 refs., 3 figs.

Relation between the microstructure and technological properties of porcelain stoneware. A review

Directory of Open Access Journals (Sweden)

Romero, M.

2015-12-01

Full Text Available Porcelain stoneware is a strongly sintered ceramic material fabricated from ball clays-quartz-feldspar mixtures. Porcelain stoneware is characterized by its excellent technical and functional properties (low water absorption, high mechanical properties, resistant to chemical substances and cleaning agents, aesthetic possibilities …. These characteristic and technical features make that among the different types of ceramic tile, porcelain stoneware is the ceramic product that in the last years has best withstood the economic crisis in the construction sector. These properties are related to the microstructure of porcelain stoneware, which is a grain and bond type with large particles of filler (quartz, mullite crystals, a silica-rich amorphous phase and porosity. The understanding of the relationship between the microstructure and the properties of porcelain stoneware is hardly important for the development and design of these materials whose tendency is the manufacture of thinner tiles with higher dimensions but must continue to comply the specific technical requirements.El gres porcelánico es un material sinterizado fabricado a partir de una mezcla de arcillas, cuarzo y feldespato. Tecnológicamente, el gres porcelánico se caracteriza por sus excelentes características técnicas y funcionales (baja absorción de agua, buenas propiedades mecánicas, resistente a substancias químicas, posibilidades estéticas…. Estas cualidades han propiciado que, entre los diferentes tipos de baldosa cerámica, es el gres porcelánico el producto que mejor ha resistido la crisis económica sufrida por el Sector de la Construcción. Las propiedades tecnológicas están relacionadas con su microestructura, compuesta de partículas de cuarzo, cristales de mullita, fase amorfa y porosidad. El conocimiento de la relación entre la microestructura y las propiedades tecnológicas del gres porcelánico es de gran importancia para avanzar en el diseño y

Effect of titania on fired characteristics of triaxial porcelain

Indian Academy of Sciences (India)

Unknown

role of each of these raw materials in triaxial bodies are discussed earlier (Lundin ... higher yield of mullite in hard porcelain up to 4%. More than 1% ZnO makes .... slit and nickel filter (Cu-Kα radiation) was used to iden- tify the various phases ...

Evolution of microstructure in flyash-containing porcelain body on ...

Indian Academy of Sciences (India)

15 wt% flyash (a calcined byproduct of thermal power plant) was incorporated in a normal triaxial kaolin–quartz–feldspar system by replacing equivalent amount of quartz. The differences in microstructural evolution on heating the compact mass of both normal and flyash-containing porcelain at different temperatures ...

Shear bond strength of veneering porcelain to zirconia: Effect of surface treatment by CNC-milling and composite layer deposition on zirconia.

Science.gov (United States)

Santos, R L P; Silva, F S; Nascimento, R M; Souza, J C M; Motta, F V; Carvalho, O; Henriques, B

2016-07-01

The purpose of this study was to evaluate the shear bond strength of veneering feldspathic porcelain to zirconia substrates modified by CNC-milling process or by coating zirconia with a composite interlayer. Four types of zirconia-porcelain interface configurations were tested: RZ - porcelain bonded to rough zirconia substrate (n=16); PZ - porcelain bonded to zirconia substrate with surface holes (n=16); RZI - application of a composite interlayer between the veneering porcelain and the rough zirconia substrate (n=16); PZI - application of a composite interlayer between the porcelain and the zirconia substrate treated by CNC-milling (n=16). The composite interlayer was composed of zirconia particles reinforced porcelain (30%, vol%). The mechanical properties of the ceramic composite have been determined. The shear bond strength test was performed at 0.5mm/min using a universal testing machine. The interfaces of fractured and untested specimens were examined by FEG-SEM/EDS. Data was analyzed with Shapiro-Wilk test to test the assumption of normality. The one-way ANOVA followed by Tukey HSD multiple comparison test was used to compare shear bond strength results (α=0.05). The shear bond strength of PZ (100±15MPa) and RZI (96±11MPa) specimens were higher than that recorded for RZ (control group) specimens (89±15MPa), although not significantly (p>0.05). The highest shear bond strength values were recorded for PZI specimens (138±19MPa), yielding a significant improvement of 55% relative to RZ specimens (p<0.05). This study shows that it is possible to highly enhance the zirconia-porcelain bond strength - even by ~55% - by combining surface holes in zirconia frameworks and the application of a proper ceramic composite interlayer. Copyright © 2016 Elsevier Ltd. All rights reserved.

Discriminative study of white porcelains by INAA and PIXE

International Nuclear Information System (INIS)

Feng, X.Q.; Feng, S.L.; Meng, F.F.; Wang, H.M.; Liu, S.S.

2005-01-01

The fine white porcelains of Xing Kiln, Ding Kiln and Jingxing Kiln are very similar or alike in many aspects, such as typology of the vessel, texture of the body, colors of the body and the glaze. It is difficult for the archaeologists to distinguish the provenance using traditional methods. Nuclear analytical techniques (INAA, PIXE, XRF, SRXRF) have been widely employed for the provenance study of cultural relics in recent years due to their unique advantage, i.e. capable of nondestructive analysis. The element contents in the body and glaze of white porcelain shards with known provenance were determined by INAA and PIXE. In the meanwhile blind samples were prepared and analyzed in the same way. The differences of the element abundance patterns were processed by multivariate statistical analysis. On the basis of the analytical data and the statistical results, the discriminating criteria for provenance identification are obtained and verified by the blind samples.

Influence of bruxism on survival of porcelain laminate veneers.

Science.gov (United States)

Granell-Ruíz, Maria; Agustín-Panadero, Rubén; Fons-Font, Antonio; Román-Rodríguez, Juan-Luis; Solá-Ruíz, María-Fernanda

2014-09-01

This study aims to determine whether bruxism and the use of occlusal splints affect the survival of porcelain laminate veneers in patients treated with this technique. Restorations were made in 70 patients, including 30 patients with some type of parafunctional habit. A total of 323 veneers were placed, 170 in patients with bruxism activity, and the remaining 153 in patients without it. A clinical examination determined the presence or absence of ceramic failure (cracks, fractures and debonding) of the restorations; these incidents were analyzed for association with bruxism and the use of splints. Analysis of the ceramic failures showed that of the 13 fractures and 29 debonding that were present in our study, 8 fractures and 22 debonding were related to the presence of bruxism. Porcelain laminate veneers are a predictable treatment option that provides excellent results, recognizing a higher risk of failure in patients with bruxism activity. The use of occlusal splints reduces the risk of fractures.

Alkali-ions diffusion, mullite formation, and crystals dissolution during sintering of porcelain bodies: Microstructural approach

DEFF Research Database (Denmark)

Leonelli, C.; Kamseu, E.; Boccaccini, Dino

2009-01-01

The effect of alkali-silicate glassy matrix as replacement for feldspar in soft and hard porcelain compositions was studied. SEM and X-ray diffraction analysis were used to evidence phase evolution. For each composition, the influence of soaking time was evaluated. The difference in chemical...... to hard porcelain. Replacing the feldspar by alkali-silicate glassy matrices with similar chemical composition, the amount of secondary mullite and mechanical properties increased in both soft and hard compositions....

A preliminary study on Fe valence of porcelain glaze by XAFS

International Nuclear Information System (INIS)

Zhang Maolin; Wang Changsui; Jin Pujun; Wei Shiqiang; Xu Wei; Chen Dongliang; Wu Ziyu

2008-01-01

Ru ware was a famous celadon in Song dynasty, whose structure analysis of glaze had always been a difficulty in scientifically analysis of ancient porcelains. The X-ray absorption fine structure spectrum (XAFS) of Fe element in glaze of Ru ware excavated in Qingliang temple was obtained. Fe valence state in porcelain glaze samples was stud/ed by Principle Component Analysis (PCA) along with linear combination fitting method. The main wavelength of the samples was also obtained by color/meter. The results show that the cyan glaze samples have great Fe 2+ /Fe 3+ , while the yellow glaze samples have small Fe 2+ /Fe 3+ . The work also showed that X-ray absorption fine structure spectrum was very suitable in nondestructive analysis of ancient ceramics. (authors)

Optimization of machining parameters of hard porcelain on a CNC ...

African Journals Online (AJOL)

Optimization of machining parameters of hard porcelain on a CNC machine by Taguchi-and RSM method. ... Journal Home > Vol 10, No 1 (2018) > ... The conduct of experiments was made by employing the Taguchi's L27 Orthogonal array to ...

Provenance and dating study on Jianyao Kiln porcelain bodies using NAA and WDXRF

International Nuclear Information System (INIS)

Feng Xiangqian; Feng Songlin; Li Jian'an; Li Dejin

2007-01-01

In order to distinguish provenance and age of Jianyao Kiln porcelains based on their chemical composition, 139 sherds that cover seven periods of production, were collected from three kiln sites. Trace and major elements in their body samples were determined by NAA and WDXRF, respectively. The analytical data and statistical analysis results show that all the body samples can be classified into 4 groups, i.e. Late Tang and Five Dynanties, Northern Song, Southern Song and Yuan. The raw materials adopted by Daluhoumen kiln site black porcelains were similar to those of Yingzhangqian site, but quite different from those of Anweishan site. (authors)

The effect of porcelain firing and type of finish line on the marginal fit of zirconia copings.

Science.gov (United States)

Vojdani, Mahroo; Safari, Anahita; Mohaghegh, Mina; Pardis, Soheil; Mahdavi, Farideh

2015-06-01

Although all-ceramic restorations are broadly used, there is a lack of information concerning how their fit is affected by fabrication procedure and marginal configuration. The purpose of this study was to evaluate the marginal fit of zirconia CAD/CAM ceramic crowns before and after porcelain firing. The influence of finish line configuration on the marginal fit was also evaluated. Twenty standardized zirconia CAD/CAM copings were fabricated for chamfer and shoulder finish line designs (n=10). The marginal fit of specimens was measured on 18 points, marked on the master metal die by using a digital microscope. After the crowns were finalized by porcelain veneering, the measurements of marginal fit were performed again. The means and standard deviations were calculated and data were analyzed using student's t-test and paired t-test (α=0.05). There were significant differences between marginal fit of chamfer and shoulder finish line groups before and after porcelain firing (p= 0.014 and p= 0.000, respectively). The marginal gap of copings with shoulder finish line was significantly smaller than those with chamfer configuration (p= 0.000), but there were no significant differences between the two marginal designs, after porcelain firing (p= 0.341). Porcelain veneering was found to have a statistically significant influence on the marginal fit of zirconia CAD/CAM crowns. Both margin configurations showed marginal gaps that were within a reported clinically acceptable range of marginal discrepancy.

Stress and Reliability Analysis of a Metal-Ceramic Dental Crown

Science.gov (United States)

Anusavice, Kenneth J; Sokolowski, Todd M.; Hojjatie, Barry; Nemeth, Noel N.

1996-01-01

Interaction of mechanical and thermal stresses with the flaws and microcracks within the ceramic region of metal-ceramic dental crowns can result in catastrophic or delayed failure of these restorations. The objective of this study was to determine the combined influence of induced functional stresses and pre-existing flaws and microcracks on the time-dependent probability of failure of a metal-ceramic molar crown. A three-dimensional finite element model of a porcelain fused-to-metal (PFM) molar crown was developed using the ANSYS finite element program. The crown consisted of a body porcelain, opaque porcelain, and a metal substrate. The model had a 300 Newton load applied perpendicular to one cusp, a load of 30ON applied at 30 degrees from the perpendicular load case, directed toward the center, and a 600 Newton vertical load. Ceramic specimens were subjected to a biaxial flexure test and the load-to-failure of each specimen was measured. The results of the finite element stress analysis and the flexure tests were incorporated in the NASA developed CARES/LIFE program to determine the Weibull and fatigue parameters and time-dependent fracture reliability of the PFM crown. CARES/LIFE calculates the time-dependent reliability of monolithic ceramic components subjected to thermomechanical and/Or proof test loading. This program is an extension of the CARES (Ceramics Analysis and Reliability Evaluation of Structures) computer program.

Effect of autoclave induced low-temperature degradation on the adhesion energy between yttria-stabilized zirconia veneered with porcelain.

Science.gov (United States)

Li, Kai Chun; Waddell, J Neil; Prior, David J; Ting, Stephanie; Girvan, Liz; van Vuuren, Ludwig Jansen; Swain, Michael V

2013-11-01

To investigate the effect of autoclave induced low-temperature degradation on the adhesion energy between yttria-stabilized zirconia veneered with porcelain. The strain energy release rate using a four-point bending stable fracture test was evaluated for two different porcelains [leucite containing (VM9) and glass (Zirox) porcelain] veneered to zirconia. Prior to veneering the zirconia had been subjected to 0 (control), 1, 5, 10 and 20 autoclave cycles. The specimens were manufactured to a total bi-layer dimension of 30 mm × 8 mm × 3 mm. Subsequent scanning electron microscopy/energy dispersive spectrometry, electron backscatter diffraction and X-ray diffraction analysis were performed to identify the phase transformation and fracture behavior. The strain energy release rate for debonding of the VM9 specimens were significantly higher (pautoclave cycles lowered the strain energy release rate significantly (pautoclave cycles between 5 and 20. The monoclinic phase reverted back to tetragonal phase after undergoing conventional porcelain firing cycles. EBSD data showed significant changes of the grain size distribution between the control and autoclaved specimen (cycle 20). Increasing autoclave cycles only significantly decreased the adhesion of the VM9 layered specimens. In addition, a conventional porcelain firing schedule completely reverted the monoclinic phase back to tetragonal. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Activation of the Cph1-dependent MAP kinase signaling pathway induces white-opaque switching in Candida albicans.

Directory of Open Access Journals (Sweden)

Bernardo Ramírez-Zavala

Full Text Available Depending on the environmental conditions, the pathogenic yeast Candida albicans can undergo different developmental programs, which are controlled by dedicated transcription factors and upstream signaling pathways. C. albicans strains that are homozygous at the mating type locus can switch from the normal yeast form (white to an elongated cell type (opaque, which is the mating-competent form of this fungus. Both white and opaque cells use the Ste11-Hst7-Cek1/Cek2 MAP kinase signaling pathway to react to the presence of mating pheromone. However, while opaque cells employ the transcription factor Cph1 to induce the mating response, white cells recruit a different downstream transcription factor, Tec1, to promote the formation of a biofilm that facilitates mating of opaque cells in the population. The switch from the white to the opaque cell form is itself induced by environmental signals that result in the upregulation of the transcription factor Wor1, the master regulator of white-opaque switching. To get insight into the upstream signaling pathways controlling the switch, we expressed all C. albicans protein kinases from a tetracycline-inducible promoter in a switching-competent strain. Screening of this library of strains showed that a hyperactive form of Ste11 lacking its N-terminal domain (Ste11(ΔN467 efficiently stimulated white cells to switch to the opaque phase, a behavior that did not occur in response to pheromone. Ste11(ΔN467-induced switching specifically required the downstream MAP kinase Cek1 and its target transcription factor Cph1, but not Cek2 and Tec1, and forced expression of Cph1 also promoted white-opaque switching in a Wor1-dependent manner. Therefore, depending on the activation mechanism, components of the pheromone-responsive MAP kinase pathway can be reconnected to stimulate an alternative developmental program, switching of white cells to the mating-competent opaque phase.

[Effect of niobium nitride on the bonding strength of titanium porcelain by magnetron sputtering].

Science.gov (United States)

Wang, Shu-shu; Zhang, La-bao; Guang, Han-bing; Zhou, Shu; Zhang, Fei-min

2010-05-01

To investigate the effect of magnetron sputtered niobium nitride (NbN) on the bonding strength of commercially pure cast titanium (Ti) and low-fusing porcelain (Ti/Vita titankeramik system). Sixty Ti specimens were randomly divided into four groups, group T1, T2, T3 and T4. All specimens of group T1 and T2 were first treated with 120 microm blasted Al2O3 particles, and then only specimens of group T2 were treated with magnetron sputtered NbN film. All specimens of group T3 and T4 were first treated with magnetron sputtered NbN film and then only specimens of group T4 were treated with 120 microm blasted Al2O3 particles. The composition of the deposits were analyzed by X-ray diffraction (XRD). A universal testing machine was used to perform the three-point bending test to evaluate the bonding strength of Ti and porcelain. The microstructure of NbN, the interface of Ti-porcelain and the fractured Ti surface were observed with scanning electron microscopy (SEM) and energy depressive spectrum (EDS), and the results were compared. The XRD results showed that the NbN deposits were cubic crystalline phases. The bonding strength of Ti and porcelain in T1 to T4 group were (27.2+/-0.8), (43.1+/-0.6), (31.4+/-1.0) and (44.9+/-0.6) MPa. These results were analyzed by one-way analysis of variance and differences between groups were compared using least significant difference test. Significant inter-group differences were found among all groups (Pporcelain, while samples treated with both Al2O3 and NbN had better bond. EDS of Ti-porcelain interface showed oxidation occurred in T1, T2 and T3, but was well controlled in T4. Magnetron sputtered NbN can prevent Ti from being oxidized, and can improve the bonding strength of Ti/Vita titankeramik system. Al2O3 blast can also improve the bonding strength of Ti/Vita titankeramik system.

Analysis of Chinese porcelains and ceramics

International Nuclear Information System (INIS)

Gihwala, D.; Vos, H.N.

1985-01-01

Trace and minor components in fragments of northern Chinese porselains and the poorly-known southern Chinese porcellaneous ware from excavations in the south-western Cape were determined non-destructively by PIXE in the glazes and in the body material. Correspondence analysis of the analytical data showed that the Chinese glazes, though different from that of English specimens, could not be differentiated. The analysis of the body material enabled the northern porcelains and some of the southern ceramics to be distinguished, but some southern porcellaneous ware could not be grouped separately

Research on the raw material source and coloring mechanism of Jiaotan Guan porcelain in south song dynasty

International Nuclear Information System (INIS)

Zhao Weijuan; Li Guoxia; Xie Jianzhong; Guo Min; Gao Zhengyao

2004-01-01

The 28 samples from Jiaotan Guan kiln, one sample of mud material in jar from ruins of Jiaotan Guan kiln, one sample of mud material in pool of practice mud, one sample of violet-golden clay near Guan kiln and four samples of glazes and bodies of the modern imitative ancient Chinese guan porcelain were analyzed by neutron activation analysis (NAA). The contents of 36 elements in each sample were measured. The NAA data were statistically treated by fuzzy cluster method and the trend cluster diagram was obtained. The results show that the raw material origin of the bodies of Jiaotan Guan porcelain is evidently different from those of glazes, the source of raw material of bodies and glazes of Jiaotan Guan kiln are stable, and the iron is assured as main coloring element. The reflecting spectrum and main wavelength of Guan porcelain glazes are determined by color analysis instrument. The relative content of structural iron (Fe 2+ , Fe 3+ ) in the glaze and the quantitative relationship between the main wavelength of glaze in various colors are determined by Moessbauer spectrum. Thus the coloring mechanism of Guan porcelain is investigated

Opaque models: Using drugs and dreams to explore the neurobiological basis of mental phenomena.

Science.gov (United States)

Langlitz, Nicolas

2017-01-01

On the basis of four historical and ethnographic case studies of modeling in neuroscience laboratories, this chapter introduces a distinction between transparent and opaque models. A transparent model is a simplified representation of a real world phenomenon. If it is not patently clear, it is at least much better comprehended than its objects of representation. An opaque model, by contrast, looks at one only partially understood phenomenon to stand in for another partially understood phenomenon. Here, the model is often just as complex as its target. Examples of such opaque models discussed in this chapter are the use of hallucinogen intoxication in humans and animals as well as the dreaming brain as models of psychosis as well as the dreaming brain as a model of consciousness in general. Several functions of opaque models are discussed, ranging from the generation of funding to the formulation of new research questions. While science studies scholars have often emphasized the epistemic fertility of failures of representation, the opacity of hallucinogen intoxications and dreams seems to have diminished the potential to produce positive knowledge from the representational relationship between the supposed models and their targets. Bidirectional comparisons between inebriation, dreaming, and psychosis, however, proved to be generative on the level of basic science. Moreover, the opaque models discussed in this chapter implicated cosmologies that steered research endeavors into certain directions rather than others. © 2017 Elsevier B.V. All rights reserved.

Shear Bond Strength of a Novel Porcelain Repair System for ...

African Journals Online (AJOL)

2018-04-04

Apr 4, 2018 ... Each fracture type was examined under a stereomicroscope .... fracture types. Statistical analysis. The normal distribution of data was examined using the Kolmogorov–Smirnov test. Shear bond strength data of repaired CAD/CAM .... adhesives to enamel, dentine, and porcelain surfaces can be compared.

The study of ancient porcelain of Hutian kiln site from Five dynasty (902-979) to Ming dynasty (1368-1644) by INAA

International Nuclear Information System (INIS)

Lin Cheng; Junling Wang; Rongwu Li; Meitian Li

2015-01-01

Minor and trace elements of 398 pieces of ancient porcelain of Hutian kiln site from Five dynasty (AD 902-979) to Ming dynasty (AD 1368-1644) were determined by instrumental neutron activate analysis (INAA). The data of INAA and PCA show the ages of all the porcelain can be divided into Five dynasty, Northern Song dynasty, Southern Song dynasty, Early Yuan dynasty, Later Yuan dynasty and Ming dynasty according to their chemical compositions. Moreover, some archaeological questions about the ancient porcelain are discussion also. (author)

75 FR 62144 - Porcelain-on-Steel Cooking Ware From China and Taiwan; Top-of-the-Stove Stainless Steel Cooking...

Science.gov (United States)

2010-10-07

...); (Investigation Nos. 701-TA-267 and 731-TA-304 (Third Review))] Porcelain-on-Steel Cooking Ware From China and Taiwan; Top-of- the-Stove Stainless Steel Cooking Ware From Korea AGENCY: United States International... porcelain-on-steel cooking ware from China and Taiwan and the antidumping and countervailing duty orders on...

[Study on corrosion resistance of three non-noble porcelain alloys].

Science.gov (United States)

Wu, Zhikai; Xu, Sheng; Li, Wei; Teng, Jin; Li, Ning

2011-10-01

To study the electrochemical corrosion behavior of Co-Cr, Ni-Cr and Ni-Cr-Be based porcelain alloys in NaCl solution. Five samples of each alloy were made respectively, electric polarization curve of each alloy was obtained using potentiodynamic polarization technique. Self-corrosion potential (E(corr)), self-corrosion current density (I(corr), passive region and transpassivation potential were tested. Microstructure and constituent was examined using scanning electron microscopy and energy dispersive spectroscopy. Co-Cr alloy possessed the most desirable corrosion resistance because of its integrated, homogeneous and compact passive film. The poor compactness of Ni-Cr alloy's passive film decreased its corrosion resistance. Ni-Cr-Be alloy exhibited the worst corrosion resistance due to the Cr and Mo depleted Ni-Be eutectic phases in the alloy. Taking biological security into consideration, it is necessary to avoid the application of porcelain alloys with Be element. Co-Cr alloy with better biocompatibility possesses much broader prospect in the field of dental restoration.

Effect of ZrO2 on the sintering behavior, strength and high-frequency dielectric properties of electrical ceramic porcelain insulator

Science.gov (United States)

Singh Mehta, Niraj; Sahu, Praveen Kumar; Ershad, Md; Saxena, Vipul; Pyare, Ram; Ranjan Majhi, Manas

2018-01-01

In the present study, the effect of ZrO2 on the sintering, strength and dielectric behavior of electrical ceramic porcelain insulator with substituting alumina content by zirconia (in weight percentage from 0% to 30%) is investigated. The different composition of samples containing different zirconia (ZrO2) contents of 0, 10, 20, and 30 wt% are prepared using the uniaxial pressure technique applying 160 MPa pressure. Further, the prepared samples are also analyzed for sintering temperatures (1350 °C), and effects are observed on mechanical and electric properties of porcelain insulator. Different characterizations such as Dilatometer, x-ray diffraction, scanning electron microscopy and differential thermal analysis/thermo gravimetric analysis were used to evaluate the thermal, phase detection, micro structural and weight loss changes by increasing concentration of ZrO2 on base porcelain composition. At 1350 °C, for the composition having 20 wt% ZrO2 with 10 wt% alumina, the maximum density was observed 2.81 g cm-3 with a porosity of 2.23%. The highest tensile strength of 41 ± 3 MPa is observed for the same sample composition. The minimum value of thermal expansion coefficient is found to be in the range of 10-6 for the sample with 30 wt% ZrO2 content sintered at 1350 °C compared to other prepared samples. Similarly, the highest dielectric value (5.1-4.4) having dielectric loss (0.08-0.12) is achieved for the sample with 30 wt% ZrO2 content sintered at 1350 °C in the frequency range of 4-20 GHz at room temperature. According to the mechanical properties, the composition having 20 wt% ZrO2 on base ceramic porcelain composition has enormous potential to serve as a high strength refractory material. For dielectric properties, the composition having 30 wt% ZrO2 is more suitable for the electrical application.

Proton Induced X-ray Emission Analysis of Sources of Raw for Blue-and-White Porcelain From Jingdezhen and Dehua Area

International Nuclear Information System (INIS)

Liu Shunmin; Yang Dawei; Li Rongwu; Li Guoxia; Cheng Huansheng; Zheng Jongxin; Chen Lifang

2010-01-01

In order to find out sources of raw, ingredients and classification relationship for Blue-and-White porcelain from Jingdezhen and Dehua area in different time, 34 Blue-and-White porcelain samples were selected. The chemical ingredients of every sample were determined by proton induced X-ray emission. The chemical ingredients data of all samples were further analyzed using fuzzy cluster analysis. The results indicate that the sources of raw and classification relationship of majority bodies from Blue-and-White porcelain of Dehua and Jingdezhen area are commendably differentiated. The sources of raw and batch formulas of eight transparent enamel samples from Jingdezhen area in Ming Dynasty and majority transparent enamel samples from Dehua area are commendably differentiated. Except one or two samples, majority Blue-and-White glaze samples from two areas are obviously different, and it might be an important path for non-destructive discrimination among Blue-and-White porcelains from two areas. (authors)

Provenance study of ancient Chinese Yaozhou porcelain by neutron activation analysis

International Nuclear Information System (INIS)

Li, R.W.; Zhao, W.J.; Li, G.X.; Xie, J.Z.; Guo, M.; Gao, Z.Y.; Feng, S.L.; Fan, D.Y.; Zhang, Y.; Cai, Z.F.; Zhuo, Z.X.

2004-01-01

The glaze samples of ancient Chinese Yaozhou porcelain were analyzed by neutron activation analysis (NAA). The contents of 29 elements for each sample were measured. the scattergram of the coloring elements shows some informations of soueces of raw materials. (authors)

Evaluating the Whitening and Microstructural Effects of a Novel Whitening Strip on Porcelain and Composite Dental Materials.

Science.gov (United States)

Takesh, Thair; Sargsyan, Anik; Lee, Matthew; Anbarani, Afarin; Ho, Jessica; Wilder-Smith, Petra

2017-08-01

The aim of this project was to evaluate the effects of 2 different whitening strips on color, microstructure and roughness of tea stained porcelain and composite surfaces. 54 porcelain and 72 composite chips served as samples for timed application of over-the-counter (OTC) test or control dental whitening strips. Chips were divided randomly into three groups of 18 porcelain and 24 composite chips each. Of these groups, 1 porcelain and 1 composite set served as controls. The remaining 2 groups were randomized to treatment with either Oral Essentials ® Whitening Strips or Crest ® 3D White Whitestrips™. Sample surface structure was examined by light microscopy, profilometry and Scanning Electron Microscopy (SEM). Additionally, a reflectance spectrophotometer was used to assess color changes in the porcelain and composite samples over 24 hours of whitening. Data points were analyzed at each time point using ANOVA. In the light microscopy and SEM images, no discrete physical defects were observed in any of the samples at any time points. However, high-resolution SEM images showed an appearance of increased surface roughness in all composite samples. Using profilometry, significantly increased post-whitening roughness was documented in the composite samples exposed to the control bleaching strips. Composite samples underwent a significant and equivalent shift in color following exposure to Crest ® 3D White Whitestrips™ and Oral Essentials ® Whitening Strips. A novel commercial tooth whitening strip demonstrated a comparable beaching effect to a widely used OTC whitening strip. Neither whitening strip caused physical defects in the sample surfaces. However, the control strip caused roughening of the composite samples whereas the test strip did not.

Porcelain tiles by the dry route

Directory of Open Access Journals (Sweden)

Boschi, A. O.

2010-10-01

Full Text Available In Brazil, the second largest tile producer of the world, at present, 70% of the tiles are produced by the dry route. One of the main reasons that lead to this development is the fact that the dry route uses approximately 30% less thermal energy them the traditional wet route. The increasing world concern with the environment and the recognition of the central role played by the water also has pointed towards privileging dry processes. In this context the objective of the present work is to study the feasibility of producing high quality porcelain tiles by the dry route. A brief comparison of the dry and wet route, in standard conditions industrially used today to produce tiles that are not porcelain tiles, shows that there are two major differences: the particle sizes obtained by the wet route are usually considerably finer and the capability of mixing the different minerals, the intimacy of the mixture, is also usually better in the wet route. The present work studied the relative importance of these differences and looked for raw materials and operational conditions that would result in better performance and glazed porcelain tiles of good quality.

En Brasil, en este momento segundo productor mundial, el 70% de los pavimentos cerámicos se obtiene por vía seca. Una de las razones fundamentales se debe a que esta vía supone un consumo energético inferior, en un 30%, a la via húmeda tradicional. La creciente preocupación mundial sobre los problemas medioambientales y el reconocimiento del papel central que juega el agua en este proceso han favorecido el desarrollo de la vía seca. En este contexto, el objetivo del presente trabajo es estudiar la viabilidad de la producción de pavimentos porcelánicos de alta calidad por vía seca. Una breve comparación entre ambas vías, en las condiciones standard de producción vigentes para producciones que no son de porcelánico, indican que existen dos diferencias substanciales; el tamaño de

Radiological impact assessment to the environment due to waste from disposal of porcelain.

Science.gov (United States)

Morsi, Tarek; Hegazy, Rehab; Badawy, Wael

2017-06-01

The present study aimed to assess the radiological parameters from gamma rays due to the uncontrolled disposal of porcelain waste to the environment. Qualitative and quantitative identification of radionuclides in the investigated samples was carried out by means of a high-purity germanium (HPGe) detector. The average activity concentrations of the local porcelain samples were measured as 208.28 Bq/kg for 226 Ra, 125.73 Bq/kg for 238 U, 84.94 Bq/kg for 232 Th and 1033.61 Bq/kg for 40 K, respectively. The imported samples had an average activity of 240.57 Bq/kg for 226 Ra, 135.56 Bq/kg for 238 U, 115.74 Bq/kg for 232 Th and 1312.49 Bq/kg for 40 K, respectively. Radiological parameters and the radium equivalent Ra eq for the investigated samples were calculated. The external and internal hazard indices, representative level index (I γ ), alpha index (I α ), and the exemption level (I x ), were estimated to be higher than the recommended value (unity), while the average activity concentrations for the studied samples were higher than recommended levels. In conclusion, we are concerned that disposal of porcelain in the environment might be a significant hazard.

Esthetic Rehabilitation of Anterior Teeth with Porcelain Laminates and Sectional Veneers

NARCIS (Netherlands)

Gresnigt, Marco; Ozcan, Mutlu

2011-01-01

Full-coverage bonded porcelain restorations offer predictable treatment options in dentistry, but a certain amount of tooth material must be removed to allow space for the required thickness of the restorative material. Laminate veneers and inlays are considered minimally invasive, but they also

Analysis of elemental maps from glaze to body of ancient Chinese Jun and Ru porcelain by micro-X-ray fluorescence

Energy Technology Data Exchange (ETDEWEB)

Cheng Lin [Key Laboratory of Beam Technology and Material Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University, Beijing Radiation Center, Beijing 100875 (China)], E-mail: chenglin@bnu.edu.cn; Li Rongwu [Department of Physics, Beijing Normal University, Beijing 100049 (China); Pan Qiuli [Key Laboratory of Beam Technology and Material Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University, Beijing Radiation Center, Beijing 100875 (China); Li Guoxia; Zhao Weijuan [Institute of Physical Engineering, Zhengzhou University, Zhengzhou 450052 (China); Liu Zhiguo [Key Laboratory of Beam Technology and Material Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University, Beijing Radiation Center, Beijing 100875 (China)

2009-01-15

The reasons how the middle layer of Ru and Jun porcelain between the glaze and body came into being are still not completely understood. Here, elemental maps from the glaze to the body of pieces of ancient Chinese Ru and Jun porcelain were analyzed by micro-X-ray fluorescence. The results show the middle layer was probably formed by the chemical composition of the glaze turning into glassy states and undergoing complex physical-chemical reactions with the body. However, the middle layer of Jun porcelain was formed by the chemical composition of the glaze turning into glassy states and then infiltrating the body at high temperatures during the firing process.

Analysis of elemental maps from glaze to body of ancient Chinese Jun and Ru porcelain by micro-X-ray fluorescence

Science.gov (United States)

Cheng, Lin; Li, Rongwu; Pan, Qiuli; Li, Guoxia; Zhao, Weijuan; Liu, Zhiguo

2009-01-01

The reasons how the middle layer of Ru and Jun porcelain between the glaze and body came into being are still not completely understood. Here, elemental maps from the glaze to the body of pieces of ancient Chinese Ru and Jun porcelain were analyzed by micro-X-ray fluorescence. The results show the middle layer was probably formed by the chemical composition of the glaze turning into glassy states and undergoing complex physical-chemical reactions with the body. However, the middle layer of Jun porcelain was formed by the chemical composition of the glaze turning into glassy states and then infiltrating the body at high temperatures during the firing process.

Development of a compact x-ray particle image velocimetry for measuring opaque flows.

Science.gov (United States)

Lee, Sang Joon; Kim, Guk Bae; Yim, Dae Hyun; Jung, Sung Yong

2009-03-01

A compact x-ray particle image velocimetry (PIV) system employing a medical x-ray tube as a light source was developed to measure quantitative velocity field information of opaque flows. The x-ray PIV system consists of a medical x-ray tube, an x-ray charge coupled device camera, a programmable shutter for a pulse-type x ray, and a synchronization device. Through performance tests, the feasibility of the developed x-ray PIV system as a flow measuring device was verified. To check the feasibility of the developed system, we tested a tube flow at two different mean velocities of 1 and 2 mm/s. The x-ray absorption of tracer particles must be quite different from that of working fluid to have a good contrast in x-ray images. All experiments were performed under atmospheric pressure condition. This system is unique and useful for investigating various opaque flows or flows inside opaque conduits.

Development of a compact x-ray particle image velocimetry for measuring opaque flows

International Nuclear Information System (INIS)

Lee, Sang Joon; Kim, Guk Bae; Yim, Dae Hyun; Jung, Sung Yong

2009-01-01

A compact x-ray particle image velocimetry (PIV) system employing a medical x-ray tube as a light source was developed to measure quantitative velocity field information of opaque flows. The x-ray PIV system consists of a medical x-ray tube, an x-ray charge coupled device camera, a programmable shutter for a pulse-type x ray, and a synchronization device. Through performance tests, the feasibility of the developed x-ray PIV system as a flow measuring device was verified. To check the feasibility of the developed system, we tested a tube flow at two different mean velocities of 1 and 2 mm/s. The x-ray absorption of tracer particles must be quite different from that of working fluid to have a good contrast in x-ray images. All experiments were performed under atmospheric pressure condition. This system is unique and useful for investigating various opaque flows or flows inside opaque conduits.

"Porcelain heart" cardiomyopathy secondary to hyperparathyroidism: radiographic, echocardiographic, and cardiac CT appearances.

LENUS (Irish Health Repository)

Freeman, James

2012-02-01

We report the radiographic, echocardiographic and cardiac CT appearances of \\'porcelain heart\\' in an 85-year-old woman who presented with progressive heart failure. The extensive myocardial calcification was secondary to hyperparathyroidism with renal failure.

"Porcelain heart" cardiomyopathy secondary to hyperparathyroidism: radiographic, echocardiographic, and cardiac CT appearances.

LENUS (Irish Health Repository)

Freeman, James

2010-11-01

We report the radiographic, echocardiographic and cardiac CT appearances of \\'porcelain heart\\' in an 85-year-old woman who presented with progressive heart failure. The extensive myocardial calcification was secondary to hyperparathyroidism with renal failure.

Moessbauer study of the firing process of the imitative ancient sky-blue Jun porcelain

International Nuclear Information System (INIS)

Gao Zhengyao; Chen Xiande

1994-01-01

Moessbauer spectra of the imitative ancient Jun porcelain indicate that the glaze and body materials contain Fe 2 O 3 , Fe 3 O 4 and structural iron. It is clear that during the firing process, the glaze undergoes dehydration, dehydroxylation, vitrification and recrystallization. The Fe 2+ quadrupole splitting value of the paramagnetic peak of the body material is high even at low firing temperatures. For the body material, the distinction between dehydration and dehydroxylation is not clear. The changes of magnetism of the glaze and body materials in the firing process and the coloring mechanism of the sky-blue Jun porcelain are analyzed in the present paper. (orig.)

Methodological study of non-destructive analysis of ancient Pb-rich glaze of porcelain by micro-X-ray fluorescence

International Nuclear Information System (INIS)

Cheng Lin; Pan Qiuli; Liu Zhiguo; Li Meitian; Jin Youshi; Li Rongwu; Fan Changsheng; Wang Shanghai

2011-01-01

The performance of the micro-X-ray fluorescence based on the slightly focusing polycapillary optics were investigated. While the chemical compositions of a piece of Pb-rich colored porcelain fired in Qing Dynasty were analyzed by micro-X-ray fluorescence. From the results, the processes of decorative technologies can be deduced as follows. A kind of pigments with high concentrations of Mn and Pb or with high concentrations of Fe and Pb was used to draw the profiles of designed paintings on the body of porcelain. Cu and its mixture with high concentration of Pb were filled in the desired positions. It is proved that polycapillary optics can play an important role in the analysis of the chemical characters and decorative technologies of pigments of colored porcelain. (authors)

The non-destructive identification of early Chinese porcelain by PIXE

International Nuclear Information System (INIS)

Cheng, H.S.; Zhang, Z.Q.; Zhang, B.; Yang, F.J.

2004-01-01

PIXE is used for the non-destructive differentiation of early precious Chinese blue and white porcelain made in Yuan (AD 1206-1368), Ming (AD 1368-1644) Dynasty in Jingdezhen from imitations. Also, ancient celadon made in Song Dynasty (AD 960-1279) is identified by measuring the trace elements contained in the glazes

The non-destructive identification of early Chinese porcelain by PIXE

Science.gov (United States)

Cheng, H. S.; Zhang, Z. Q.; Zhang, B.; Yang, F. J.

2004-06-01

PIXE is used for the non-destructive differentiation of early precious Chinese blue and white porcelain made in Yuan (AD 1206-1368), Ming (AD 1368-1644) Dynasty in Jingdezhen from imitations. Also, ancient celadon made in Song Dynasty (AD 960-1279) is identified by measuring the trace elements contained in the glazes.

Energy dependence of opaqueness for pp collisions at high energies

CERN Document Server

Chou, T T

1978-01-01

Opaqueness of pp collisions is evaluated at three CERN-ISR energies. Comparisons with predictions of the factorisable eikonal models and the scaling hypothesis are made. It appears that results are in favour of the factorisable models. (20 refs).

Esthetic modification of cast dental-ceramic restorations.

Science.gov (United States)

Campbell, S D

1990-01-01

The advantages and disadvantages of conventional opaque substructures (eg, metal ceramic restorations) used for creating esthetic complete crown restorations are reviewed, and the esthetic advantages of veneering a translucent crown (Dicor) are considered. An appropriate aluminous veneering porcelain was identified (Vitadur Veneer). This veneer porcelain was chosen to match the thermal coefficient of expansion of the cast glass-ceramic substructure. A flexural strength study was then completed and it showed no difference in the strength of the veneered and nonveneered translucent cast glass-ceramic specimens. Scanning electron microscopy revealed that the interface between the porcelain veneer and cast glass-ceramic substructure had no visible porosity and resulted in a continuous-appearing structure. Potential coping designs, as well as the clinical applications and ramifications of this modified crown, are discussed.

A XANES study of cobalt speciation state in blue-and-white glazes from 16th to 17th century Chinese porcelains

Energy Technology Data Exchange (ETDEWEB)

Figueiredo, M.O., E-mail: ondina.figueiredo@lneg.pt [CENIMAT/I3N, Faculty Sciences and Technology, New University of Lisbon, Campus da Caparica, 2829-516 Caparica (Portugal); National Laboratory of Energy and Geology (LNEG), Apartado 7586, 2721-866 Alfragide (Portugal); Silva, T.P. [National Laboratory of Energy and Geology (LNEG), Apartado 7586, 2721-866 Alfragide (Portugal); CENIMAT/I3N, Faculty Sciences and Technology, New University of Lisbon, Campus da Caparica, 2829-516 Caparica (Portugal); Veiga, J.P. [CENIMAT/I3N, Faculty Sciences and Technology, New University of Lisbon, Campus da Caparica, 2829-516 Caparica (Portugal)

2012-04-15

Highlights: Black-Right-Pointing-Pointer Speciation of cobalt in ancient Chinese porcelain glazes studied by X-ray absorption near-edge spectroscopy. Black-Right-Pointing-Pointer Blue pigmenting role of tetrahedral Co{sup 2+} ions. Black-Right-Pointing-Pointer Uncertainties in deducing a formal valence state for cobalt ions from the edge energy. - Abstract: The composition of cobalt blue pigments used in ancient blue-and-white Chinese glazes is known to have changed between the 14th and the 17th century and ratios of some main chemical components plus trace elements are relevant guide-lines to establish the porcelain manufacture period. Once archaeological findings of Chinese porcelains can contribute to set up dating processes, a study of blue-and-white porcelain shards recovered during recent excavations in Lisbon Old-City was carried out by non-destructive laboratory X-ray fluorescence spectrometry for chemical characterization, combined with X-ray absorption spectroscopy (XAS) using synchrotron radiation to ascertain the formal valence and coordination of pigmenting cobalt ions. Following a preliminary extended X-ray absorption fine-structure study that revealed a coordination of divalent cobalt ions slightly above four, a detailed analysis of the near-edge region of Co 1s X-ray absorption spectra (XANES) was carried out on the blue-and-white glazes from those archaeological Chinese porcelain fragments. Pre-edge features and edge details are discussed in comparison with XANES spectra obtained from model compounds with well known crystal structure - Co{sub 3}O{sub 4}, CoAl{sub 2}O{sub 4} and Co{sub 2}SiO{sub 4}, plus a cobalt-based blue pigment (cerulean). Present chemical data validate the manufacture period of studied Chinese porcelains advanced by Art Historians on the single basis of stylistic features (late 16th and medium 17th century). Spectroscopic results confirm a coordination environment of pigmenting Co{sup 2+} ions close to tetrahedral and

A XANES study of cobalt speciation state in blue-and-white glazes from 16th to 17th century Chinese porcelains

International Nuclear Information System (INIS)

Figueiredo, M.O.; Silva, T.P.; Veiga, J.P.

2012-01-01

Highlights: ► Speciation of cobalt in ancient Chinese porcelain glazes studied by X-ray absorption near-edge spectroscopy. ► Blue pigmenting role of tetrahedral Co 2+ ions. ► Uncertainties in deducing a formal valence state for cobalt ions from the edge energy. - Abstract: The composition of cobalt blue pigments used in ancient blue-and-white Chinese glazes is known to have changed between the 14th and the 17th century and ratios of some main chemical components plus trace elements are relevant guide-lines to establish the porcelain manufacture period. Once archaeological findings of Chinese porcelains can contribute to set up dating processes, a study of blue-and-white porcelain shards recovered during recent excavations in Lisbon Old-City was carried out by non-destructive laboratory X-ray fluorescence spectrometry for chemical characterization, combined with X-ray absorption spectroscopy (XAS) using synchrotron radiation to ascertain the formal valence and coordination of pigmenting cobalt ions. Following a preliminary extended X-ray absorption fine-structure study that revealed a coordination of divalent cobalt ions slightly above four, a detailed analysis of the near-edge region of Co 1s X-ray absorption spectra (XANES) was carried out on the blue-and-white glazes from those archaeological Chinese porcelain fragments. Pre-edge features and edge details are discussed in comparison with XANES spectra obtained from model compounds with well known crystal structure – Co 3 O 4 , CoAl 2 O 4 and Co 2 SiO 4 , plus a cobalt-based blue pigment (cerulean). Present chemical data validate the manufacture period of studied Chinese porcelains advanced by Art Historians on the single basis of stylistic features (late 16th and medium 17th century). Spectroscopic results confirm a coordination environment of pigmenting Co 2+ ions close to tetrahedral and substantiate the dual role of cobalt as network former plus modifier in the glaze of ancient Chinese porcelains.

Analysis of bluish-white porcelain of Fanchang kiln in Anhui province by INAA

International Nuclear Information System (INIS)

Yang Yuzhang; Zhang Juzhong

2008-01-01

The minor and trace elements in the bluish-white porcelain bodies of Fanchang kiln in different dynasties were determined by instrumental neutron activation analysis (INAA). Multivariable statistical analysis of the experimental data was carried out by SPSS software. The results show that the contents of Yb, Ta, Hf and Th varied notably between early and middle North Song Dynasty. The chemical compositions of Fanchang porcelain bodies can be divided into three groups corresponding to Five Dynasties, early Northern Song and middle Northern Song. Combined with the results of major elements analysis, we think that the raw materials of Fanchang kiln varied in different periods and the using up of fine raw materials was the main reason of Fanchang kiln's decline. (authors)

Study on ancient porcelain of Loulinpo Kiln Site by nuclear analysis technology

International Nuclear Information System (INIS)

Wang, Y.Q.; Feng, S.L.; Feng, X.Q.; Lei, Y.; Cheng, L.; Xu, Q.; Zhou, Z.X.; Xue, D.X.

2005-01-01

Yaozhou Kiln located at Tongchuan of Shanxi Province has lasted continuous history of firing celadon porcelain from Tang Dynasty (618-907A.D.) to Yuan Dynasty (1234-1368A.D.), The firing technology has had important effect for celadon porcelain of many kilns in ancient China. In Jin Dynasty (1127-1234A.D.) and Yuan Dynasty, because of lacking of raw material resources, the central site of Yaozhou Kiln moved from Tongchuan to Lidipo, Shangdian and Chenlu area. Luolinpo site belongs to Yaozhou Kiln series and is one kiln of Shangdian area. The bowl sherds samples of Yuan dynasty stratum excavated in recent year. The glaze color is celadon, black, dark brown and dark reddish brown respectively. Ten pieces of sherds of each glaze color were selected. The main chemical compositions of theses samples were analyzed by XRF and the trace elemental contents were determined by NAA. The result shown that the content of Fe 2 O 3 can decide the kind of glaze color will be. The concentration of CaO, Na 2 O and K 2 O can be used to explain the developing process of firing techniques. Except samples of dark brown glaze, the contents of Fe 2 O 3 and CaO change in small range. The proportions of these main chemical compositions of the porcelain with glaze color of black, celadon and dark reddish brown have little variation. But it was very different form some samples of dark brown glaze.

Esthetic restorations of maxillary anterior teeth with orthodontic treatment and porcelain laminate veneers: a case report.

Science.gov (United States)

Moon, Ji-Eun; Kim, Sung-Hun; Han, Jung-Suk; Yang, Jae-Ho; Lee, Jai-Bong

2010-06-01

If orthodontists and restorative dentists establish the interdisciplinary approach to esthetic dentistry, the esthetic and functional outcome of their combined efforts will be greatly enhanced. This article describes satisfying esthetic results obtained by the distribution of space for restoration by orthodontic treatment and porcelain laminate veneers in uneven space between maxillary anterior teeth. It is proposed that the use of orthodontic treatment for re-distribution of the space and the use of porcelain laminate veneers to alter crown anatomy provide maximum esthetic and functional correction for patients with irregular interdental spacing.

Diminutive Porcelain Ascending Aorta With Supravalvular Aortic Stenosis.

Science.gov (United States)

Houmsse, Mustafa; McDavid, Asia; Kilic, Ahmet

2018-05-01

This report describes the case of a 49-year-old man with a medical history significant for congenital aortic stenosis. The patient presented with progressive shortness of breath and decreased stamina and was found to have a concentric, diminutive porcelain ascending aorta with diffuse supravalvular aortic stenosis. We describe treatment with an aortic root augmentation and Bentall procedure using hypothermic circulatory arrest. Copyright © 2018 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Illustration of compositional variations over time of Chinese porcelain glazes combining micro-X-ray Fluorescence spectrometry, multivariate data analysis and Seger formulas

Energy Technology Data Exchange (ETDEWEB)

Van Pevenage, J., E-mail: Raman@UGent.be [Department of Analytical Chemistry, Raman Spectroscopy Research Group, Ghent University, Krijgslaan 281, S12, B-9000 Ghent (Belgium); Verhaeven, E. [Department of Conservation and Restoration, University College Antwerp, Blindestraat 9, B-2000 Antwerp (Belgium); Vekemans, B. [Department of Analytical Chemistry, Ghent University, Krijgslaan 281, S12, B-9000 Ghent (Belgium); Lauwers, D., E-mail: Raman@UGent.be [Department of Analytical Chemistry, Raman Spectroscopy Research Group, Ghent University, Krijgslaan 281, S12, B-9000 Ghent (Belgium); Herremans, D.; De Clercq, W. [Department of Archaeology, Ghent University, Sint-Pietersnieuwstraat 35, B-9000 Ghent (Belgium); Vincze, L. [Department of Analytical Chemistry, Ghent University, Krijgslaan 281, S12, B-9000 Ghent (Belgium); Moens, L., E-mail: Raman@UGent.be [Department of Analytical Chemistry, Raman Spectroscopy Research Group, Ghent University, Krijgslaan 281, S12, B-9000 Ghent (Belgium); Vandenabeele, P. [Department of Archaeology, Ghent University, Sint-Pietersnieuwstraat 35, B-9000 Ghent (Belgium)

2015-01-01

In this research, the transparent glaze layers of Chinese porcelain samples were investigated. Depending on the production period, these samples can be divided into two groups: the samples of group A dating from the Kangxi period (1661–1722), and the samples of group B produced under emperor Qianlong (1735–1795). Due to the specific sample preparation method and the small spot size of the X-ray beam, investigation of the transparent glaze layers is enabled. Despite the many existing research papers about glaze investigations of ceramics and/or porcelain ware, this research reveals new insights into the glaze composition and structure of Chinese porcelain samples. In this paper it is demonstrated, using micro-X-ray Fluorescence (μ-XRF) spectrometry, multivariate data analysis and statistical analysis (Hotelling's T-Square test) that the transparent glaze layers of the samples of groups A and B are significantly different (95% confidence level). Calculation of the Seger formulas, enabled classification of the glazes. Combining all the information, the difference in composition of the Chinese porcelain glazes of the Kangxi period and the Qianlong period can be demonstrated. - Highlights: • Fully described methodology for the analysis of silicate glazes of Chinese porcelain samples • The combination of a semi-quantitative analysis of silicate glazes, multi-variate data and statistical analysis. • The use of Seger formula to understand better the composition of the glazes. • New insights into the glaze composition and structure of Chinese porcelain glazes of different time periods.

Illustration of compositional variations over time of Chinese porcelain glazes combining micro-X-ray Fluorescence spectrometry, multivariate data analysis and Seger formulas

International Nuclear Information System (INIS)

Van Pevenage, J.; Verhaeven, E.; Vekemans, B.; Lauwers, D.; Herremans, D.; De Clercq, W.; Vincze, L.; Moens, L.; Vandenabeele, P.

2015-01-01

In this research, the transparent glaze layers of Chinese porcelain samples were investigated. Depending on the production period, these samples can be divided into two groups: the samples of group A dating from the Kangxi period (1661–1722), and the samples of group B produced under emperor Qianlong (1735–1795). Due to the specific sample preparation method and the small spot size of the X-ray beam, investigation of the transparent glaze layers is enabled. Despite the many existing research papers about glaze investigations of ceramics and/or porcelain ware, this research reveals new insights into the glaze composition and structure of Chinese porcelain samples. In this paper it is demonstrated, using micro-X-ray Fluorescence (μ-XRF) spectrometry, multivariate data analysis and statistical analysis (Hotelling's T-Square test) that the transparent glaze layers of the samples of groups A and B are significantly different (95% confidence level). Calculation of the Seger formulas, enabled classification of the glazes. Combining all the information, the difference in composition of the Chinese porcelain glazes of the Kangxi period and the Qianlong period can be demonstrated. - Highlights: • Fully described methodology for the analysis of silicate glazes of Chinese porcelain samples • The combination of a semi-quantitative analysis of silicate glazes, multi-variate data and statistical analysis. • The use of Seger formula to understand better the composition of the glazes. • New insights into the glaze composition and structure of Chinese porcelain glazes of different time periods

A pilot study comparing opaque, weighted bottles with conventional, clear bottles for infant feeding.

Science.gov (United States)

Ventura, Alison K; Pollack Golen, Rebecca

2015-02-01

It is hypothesized that the visual and weight cues afforded by bottle-feeding may lead mothers to overfeed in response to the amount of liquid in the bottle. The aim of the present pilot study was to test this hypothesis by comparing mothers' sensitivity and responsiveness to infant cues and infants' intakes when mothers use opaque, weighted bottles (that remove visual and weight cues) compared to conventional, clear bottles to feed their infants. We also tested the hypothesis that mothers' pressuring feeding style would moderate the effect of bottle type. Formula-feeding dyads (N = 25) visited our laboratory on two separate days. Mothers fed their infants from a clear bottle one day and an opaque, weighted bottle on the other; bottle-order was counterbalanced across the two days. Infant intake was assessed by weighing each bottle before and after the feeding. Maternal sensitivity and responsiveness to infant cues was objectively assessed using the Nursing Child Assessment Feeding Scale. Mothers were significantly more responsive to infant cues when they used opaque compared to clear bottles (p = .04). There was also a trend for infants to consume significantly less formula when fed from opaque compared to clear bottles (p = .08). Mothers' pressuring feeding style moderated the effect of bottle type on maternal responsiveness to infant cues (p = .02) and infant intake (p = .03). Specifically, mothers who reported higher levels of pressuring feeding were significantly more responsive to their infants' cues (p = .02) and fed their infants significantly less formula when using opaque versus clear bottles (p = .01); no differences were seen for mothers who reported lower levels of pressuring feeding. This study highlights a simple, yet effective intervention for improving the bottle-feeding practices of mothers who have pressuring feeding styles. Copyright © 2014 Elsevier Ltd. All rights reserved.

Investigation of some ancient opaque glasses in the archaeological museums of Istanbul by x-ray radiography technique

International Nuclear Information System (INIS)

Tugrul, B.; Sungur, F.; Atik, S.

1986-01-01

In this study, opaque glass samples of which interiors is invisible, investigated by the x-ray radiography technique. In the evaluation,some knowledge has been extracted about the glass base and mold technique. Furthermore,it was shown that ornamental attachments have been fixed on the glass artifacts by techniques different than what it appears to be. In addition to that, joining edges of restorated opaque glass samples can be investigated and quality of the restoration can be evaluated. Therefore, the opaque glass samples were investigated non-destructively a short period of time, much like transparent glass could be studied. (author)

Resin cements formulated with thio-urethanes can strengthen porcelain and increase bond strength to ceramics.

Science.gov (United States)

Bacchi, Atais; Spazzin, Aloisio Oro; de Oliveira, Gabriel Rodrigues; Pfeifer, Carmem; Cesar, Paulo Francisco

2018-06-01

The use of thio-urethane oligomers has been shown to significantly improve the mechanical properties of resin cements (RCs). The aim of this study was to use thio-urethane-modified RC to potentially reinforce the porcelain-RC structure and to improve the bond strength to zirconia and lithium disilicate. Six oligomers were synthesized by combining thiols - pentaerythritol tetra-3-mercaptopropionate (PETMP, P) or trimethylol-tris-3-mercaptopropionate (TMP, T) - with di-functional isocyanates - 1,6-Hexanediol-diissocyante (HDDI) (aliphatic, AL) or 1,3-bis(1-isocyanato-1-methylethyl)benzene (BDI) (aromatic, AR) or Dicyclohexylmethane 4,4'-Diisocyanate (HMDI) (cyclic, CC). Thio-urethanes (20 wt%) were added to a BisGMA/UDMA/TEGDMA organic matrix. Filler was introduced at 60 wt%. The microshear bond strength (μSBS), Weibull modulus (m), and failure pattern of RCs bonded to zirconia (ZR) and lithium disilicate (LD) ceramics was evaluated. Biaxial flexural test and fractographic analysis of porcelain discs bonded to RCs were also performed. The biaxial flexural strength (σ bf ) and m were calculated in the tensile surfaces of porcelain and RC structures (Z = 0 and Z = -t 2 , respectively). The μSBS was improved with RCs formulated with oligomers P_AL or T_AL bonded to LD and P_AL, P_AR or T_CC bonded to zirconia in comparison to controls. Mixed failures predominated in all groups. σ bf had superior values at Z = 0 with RCs formulated with oligomers P_AL, P_AR, T_AL, or T_CC in comparison to control; σ bf increased with all RCs composed by thio-urethanes at Z = -t 2 . Fractographic analysis revealed all fracture origins at Z = 0. The use of specific thio-urethane oligomers as components of RCs increased both the biaxial flexural strength of the porcelain-RC structure and the μSBS to LD and ZR. The current investigation suggests that it is possible to reinforce the porcelain-RC pair and obtain higher bond strength to LD and ZR with RCs

The Moessbauer experiment on the clays and the imitative ancient porcelains

International Nuclear Information System (INIS)

Gao Zhengyao; Chen Songhua

1995-12-01

It is analyzed that Moessbauer parameter variations of clays from the famous sites of ancient kilns change with temperature, time and atmosphere in firing process. The variation of the Moessbauer parameters of the imitative ancient Chinese Ru porcelain sky-green glaze with the firing conditions is studied in detail. The Moessbauer spectra show that the sky-green glaze contains three kinds of iron minerals, i.e. the structural iron (Fe 2+ and Fe 3+ ); Fe 2 O 3 and Fe 3 O 4 ; The relative intensity of the paramagnetic peak Fe 2+ increases and the magnetic ratio of the magnetic peak decreases with increasing temperature. Based on the variation of the quadrupole splitting (QS) of the paramagnetic peak Fe 2+ , the phase transformation characteristics of the sky-green glaze in the firing process is discussed. The coloring mechanism of the sky-green glaze and the variation of its magnetism in the firing process are also investigated. The variation of the hyperfine interaction parameters and the variable mechanism of the sky-green glaze at liquid helium temperature is studied. Moessbauer spectra of the imitative ancient blue Jun porcelain indicate that the glaze and boby materials contain Fe 2 O 3 , Fe 3 O 4 and structural iron. It is clear that during the firing process, the glaze undergoes dehydration, dehydroxylation, vitrification and recrystallization. The Fe 2+ quadrupole splitting value of the paramagnetic peak of the body material is rather high even at low firing temperature. The distinction between dehydration and dehyroxylation is not clear. The changes of magnetism of the glaze and body materials in the firing process and coloring mechanism of the sky-blue Jun porcelain are analyzed

Influences of chemical packing and the chemical composition in porcelain sintering: from theory to practice

International Nuclear Information System (INIS)

Conceicao, E.S.; Gouvea, D.; Romano, R.C.O.; Pileggi, R.G.

2011-01-01

Studies have been conducted using the size distribution particles as a tool to obtain maximum packing in porcelain bodies. However, little attention has been given for the maximum size of particles and its effect in the sintering. While some particles are relatively large (63 μ m) for some oxides in the porcelain composition, they could compromise the sintering if a liquid phase is formed during heat processing. In this work, a comparative analysis showed that compositions with a maximum green packing density does not always lead to a maximum final densification in sintering if there is no control of the maximum size of the particles. (author)

Influence of porcelain firing and cementation on the marginal adaptation of metal-ceramic restorations prepared by different methods.

Science.gov (United States)

Kaleli, Necati; Saraç, Duygu

2017-05-01

Marginal adaptation plays an important role in the survival of metal-ceramic restorations. Porcelain firings and cementation may affect the adaptation of restorations. Moreover, conventional casting procedures and casting imperfections may cause deteriorations in the marginal adaptation of metal-ceramic restorations. The purpose of this in vitro study was to compare the marginal adaptation after fabrication of the framework, porcelain application, and cementation of metal-ceramic restorations prepared by using the conventional lost-wax technique, milling, direct metal laser sintering (DMLS), and LaserCUSING, a direct process powder-bed system. Alterations in the marginal adaptation of the metal frameworks during the fabrication stages and the precision of fabrication methods were evaluated. Forty-eight metal dies simulating prepared premolar and molar abutment teeth were fabricated to investigate marginal adaptation. They were divided into 4 groups (n=12) according to the fabrication method used (group C serving as the control group: lost-wax method; group M: milling method; group LS: DMLS method; group DP: direct process powder-bed method). Sixty marginal discrepancy measurements were recorded separately on each abutment tooth after fabrication of the framework, porcelain application, and cementation by using a stereomicroscope. Thereafter, each group was divided into 3 subgroups according to the measurements recorded in each fabrication stage: subgroup F (framework), subgroup P (porcelain application), and subgroup C (cementation). Data were statistically analyzed with univariate analysis of variance (followed by 1-way ANOVA and Tamhane T2 test (α=.05). The lowest marginal discrepancy values were observed in restorations prepared by using the direct process powder-bed method, and this was significantly different (Pdirect process powder-bed method is quite successful in terms of marginal adaptation. The marginal discrepancy increased after porcelain application

Characterization of the waste from porcelain polish submitted to the hydrocycloning process

International Nuclear Information System (INIS)

Caetano, A.L.A.; Barbosa Neto, M.C.; Fulgencio, E.B.Gr.; Macedo, D.A.; Ferreira, H.S.; Dutra, R.P.S.

2016-01-01

The residue generated in porcelain tile polishing has caused great social and environmental worry, due to the release of its solid effluents in inadequate places. This study aims to characterize the residue came from porcelain tile polishing, in order to reuse it in own ceramic industry. For this, was used a laboratory hydrocyclone, equipment used for separation of particles by size. The use of this type of process in the treatment of natural materials can represent quite an efficient tool and cost affordable for the purification of these, since allows to there are separation between the fractions. The different samples were characterized by X-ray diffraction, X-ray fluorescence, particle size analysis and thermal analysis. The results indicate that the resulting material from this process showed different characteristics of the material that was not hydrocycloned, especially as the intensity of the mineralogical phases and the particle size distribution. (author)

Strain gauge analysis of the effect of porcelain firing simulation on the prosthetic misfit of implant-supported frameworks.

Science.gov (United States)

De Vasconcellos, Diego Klee; Özcan, Mutlu; Maziero Volpato, Cláudia Ângela; Bottino, Marco Antonio; Yener, Esra Salihoğlu

2012-06-01

This study investigated the effect of porcelain firing on the misfit of implant-supported frameworks and analyzed the influence of preheat treatment on the dimensional alterations. Four external-hex cylindrical implants were placed in polyurethane block. Ten frameworks of screw-retained implant-supported prostheses were cast in Pd-Ag using 2 procedures: (1) control group (CG, n = 5): cast in segments and laser welded; and test group (TG, n = 5): cast in segments, preheated, and laser welded. All samples were subjected to firing to simulate porcelain veneering firing. Strain gauges were bonded around the implants, and microstrain values (με = 10⁻⁶ε) were recorded after welding (M1), oxidation cycle (M2), and glaze firing (M3). Data were statistically analyzed (2-way analysis of variance, Bonferroni, α = 0.05). The microstrain value in the CG at M3 (475.2 με) was significantly different from the values observed at M1 (355.6 με) and M2 (413.9 με). The values at M2 and M3 in the CG were not statistically different. Microstrain values recorded at different moments (M1: 361.6 με/M2: 335.3 με/M3: 307.2 με) did not show significant difference. The framework misfit deteriorates during firing cycles of porcelain veneering. Metal distortion after porcelain veneering could be controlled by preheat treatment.

Clay Treatment To Improve Its Color Parameters To Use Them In Porcelain Stoneware Production

International Nuclear Information System (INIS)

Llop, M.; Notari, M.D.; Barrachina, E.; Nebot, I.; Nunez, I.; Carda, J.B.

2010-01-01

The porcelain stoneware tiles production needs high whiteness clays in order to be competitive in the ceramic sector. In the present work, Spanish clays used in the porcelain stoneware tiles production have been characterized in physic, chemist and mineralogical terms, in order to reduce its content of chromophore oxides (Fe2O3 and TiO2). These reduction processes are concerned with different physical and chemical treatments, as sieving at 150mm, magnetic separation using a 0.6T permanent magnet, or acid treatment with HCL and later neutralization with NH3. With these treatments, due to siderite elimination, chromophore oxides as Fe2O3 have been decreased from 2,36% to 1,66% in the chemically treated clay. (Author).

Direct determination of trace rare earth elements in ancient porcelain samples with slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry

International Nuclear Information System (INIS)

Xiang Guoqiang; Jiang Zucheng; He Man; Hu Bin

2005-01-01

A method for the direct determination of trace rare earth elements in ancient porcelain samples by slurry sampling fluorinating electrothermal vaporization inductively coupled plasma mass spectrometry was developed with the use of polytetrafluoroethylene as fluorinating reagent. It was found that Si, as a main matrix element in ancient porcelain sample, could be mostly removed at the ashing temperature of 1200 deg. C without considerable losses of the analytes. However, the chemical composition of ancient porcelain sample is very complicated, which makes the influences resulting from other matrix elements not be ignored. Therefore, the matrix effect of ancient porcelain sample was also investigated, and it was found that the matrix effect is obvious when the matrix concentration was larger than 0.8 g l -1 . The study results of particle size effect indicated that when the sample particle size was less than 0.057 mm, the particle size effect is negligible. Under the optimized operation conditions, the detection limits for rare earth elements by fluorinating electrothermal vaporization inductively coupled plasma mass spectrometry were 0.7 ng g -1 (Eu)-33.3 ng g -1 (Nd) with the precisions of 4.1% (Yb)-10% (La) (c = 1 μg l -1 , n = 9). The proposed method was used to directly determine the trace rare earth elements in ancient porcelain samples produced in different dynasty (Sui, Ming and Qing), and the analytical results are satisfactory

Experimental Analysis and Model Validation of an Opaque Ventilated Facade

DEFF Research Database (Denmark)

López, F. Peci; Jensen, Rasmus Lund; Heiselberg, Per

2012-01-01

Natural ventilation is a convenient way of reducing energy consumption in buildings. In this study an experimental module of an opaque ventilated façade (OVF) was built and tested for assessing its potential of supplying free ventilation and air preheating for the building. A numerical model was ...

Preliminary assessment of metal-porcelain bonding strength of CoCrW alloy after 3 wt.% Cu addition

International Nuclear Information System (INIS)

Lu, Yanjin; Zhao, Chaoqian; Ren, Ling; Guo, Sai; Gan, Yiliang; Yang, Chunguang; Wu, Songquan; Lin, Junjie; Huang, Tingting; Yang, Ke; Lin, Jinxin

2016-01-01

In this work, a novel Cu-bearing CoCrW alloy fabricated by selective laser melting for dental application has been studied. For its successful application, the bonding strength of metal-porcelain is essential to be systematically investigated. Therefore, the aim of this study was to evaluate the metal-porcelain bonding strength of CoCrWCu alloy by three-point bending test, meanwhile the Ni-free CoCrW alloy was used as control. The oxygen content was investigated by an elemental analyzer; X-ray photoelectron spectroscopy (XPS) was used to analyze the surface chemical composition of CoCrW based alloy after preoxidation treatment; the fracture mode was investigated by X-ray energy spectrum analysis (EDS) and scanning electron microscope (SEM). Result from the oxygen content analysis showed that the content of oxygen dramatically increased after the Cu addition. And the XPS suggested that Co-oxidation, Cr_2O_3, CrO_2, WO_3, Cu_2O and CuO existed on the preoxidated surface of the CoCrWCu alloy; the three-point bending test showed that the bonding strength of the CoCrWCu alloy was 43.32 MPa, which was lower than that of the CoCrW group of 47.65 MPa. However, the average metal-porcelain bonding strength is significantly higher than the minimum value in the ISO 9693 standard. Results from the SEM images and EDS indicated that the fracture mode of CoCrWCu-porcelain was mixed between cohesive and adhesive. Based on the results obtained in this study, it can be indicated that the Cu-bearing CoCrW alloy fabricated by the selective laser melting is a promising candidate for use in dental application. - Highlights: • The bonding strength of metal-porcelain was slightly decreased with Cu addition; • Cu not only led to promote the diffusion of O and W element but also inhibited the diffusivity of Co in the outward direction; • The changed oxidation behavior resulted in lowering the bonding strength;

Preliminary assessment of metal-porcelain bonding strength of CoCrW alloy after 3 wt.% Cu addition

Energy Technology Data Exchange (ETDEWEB)

Lu, Yanjin; Zhao, Chaoqian [Key Laboratory of Optoelectronic Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, 155Yangqiao Road West, Fuzhou (China); Ren, Ling [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang (China); Guo, Sai; Gan, Yiliang [Key Laboratory of Optoelectronic Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, 155Yangqiao Road West, Fuzhou (China); Yang, Chunguang [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang (China); Wu, Songquan; Lin, Junjie; Huang, Tingting [Key Laboratory of Optoelectronic Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, 155Yangqiao Road West, Fuzhou (China); Yang, Ke, E-mail: kyang@imr.ac.cn [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang (China); Lin, Jinxin, E-mail: franklin@fjirsm.ac.cn [Key Laboratory of Optoelectronic Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, 155Yangqiao Road West, Fuzhou (China)

2016-06-01

In this work, a novel Cu-bearing CoCrW alloy fabricated by selective laser melting for dental application has been studied. For its successful application, the bonding strength of metal-porcelain is essential to be systematically investigated. Therefore, the aim of this study was to evaluate the metal-porcelain bonding strength of CoCrWCu alloy by three-point bending test, meanwhile the Ni-free CoCrW alloy was used as control. The oxygen content was investigated by an elemental analyzer; X-ray photoelectron spectroscopy (XPS) was used to analyze the surface chemical composition of CoCrW based alloy after preoxidation treatment; the fracture mode was investigated by X-ray energy spectrum analysis (EDS) and scanning electron microscope (SEM). Result from the oxygen content analysis showed that the content of oxygen dramatically increased after the Cu addition. And the XPS suggested that Co-oxidation, Cr{sub 2}O{sub 3}, CrO{sub 2}, WO{sub 3}, Cu{sub 2}O and CuO existed on the preoxidated surface of the CoCrWCu alloy; the three-point bending test showed that the bonding strength of the CoCrWCu alloy was 43.32 MPa, which was lower than that of the CoCrW group of 47.65 MPa. However, the average metal-porcelain bonding strength is significantly higher than the minimum value in the ISO 9693 standard. Results from the SEM images and EDS indicated that the fracture mode of CoCrWCu-porcelain was mixed between cohesive and adhesive. Based on the results obtained in this study, it can be indicated that the Cu-bearing CoCrW alloy fabricated by the selective laser melting is a promising candidate for use in dental application. - Highlights: • The bonding strength of metal-porcelain was slightly decreased with Cu addition; • Cu not only led to promote the diffusion of O and W element but also inhibited the diffusivity of Co in the outward direction; • The changed oxidation behavior resulted in lowering the bonding strength;.

[Effects of different concentrations of MgSiF(6) as electrolyte for micro-arc oxidation on the bond strength between titanium and porcelain].

Science.gov (United States)

Yuan, M J; Zhang, S J; Liu, J; Tan, F

2018-02-09

Objective: To investigate the effects of different concentrations of MgSiF(6) as electrolyte on the bond strength between titanium and porcelain after micro-arc oxidation (MAO) treatment and screen the suitable concentration of MgSiF(6) that can improve the bond strength between titanium and porcelain. Methods: Four different concentrations of MgSiF(6) (10, 20, 30, 40 g/L) were chosen as MAO reaction solutions. Sandblasting treatment was selected as a control group. After porcelain was fused to each specimen, titanium-porcelain bond strengths were evaluated by the three-point bending test according to ISO 9693. Scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) were adopted to evaluate the morphologies and elemental compositions of both the MAO coatings and the interfaces of the titanium-porcelain restoration. Results: The surface of titanium specimen in the control group was sharp and rough, while specimens in both 10 g/L group and 20 g/L group were porous and homogeneous. However, the pores found on the specimens in the latter group were larger in diameter (approximately 1.0-2.0 μm) than those on the former one (0.2-0.5 μm). The bond strengths of the control group and the experimental groups (10, 20, 30, 40 g/L MgSiF(6)) were (27.08±3.16), (38.18±2.65), (44.75±2.21), (36.44±2.04), (31.04±2.59) MPa, respectively. All the experimental groups showed higher bond strengths than the control group did ( Pporcelain were tight and compact in the 20 g/L group, while different amounts of pores and cracks were visible in the other groups. Additionally, after the three-point bending test, few residual porcelains could be observed on the surfaces of specimens in the control group. Conclusions: MAO treatment with 20 g/L MgSiF(6) on titanium can improve bonding strength between titanium and porcelain.

Color management of porcelain veneers: influence of dentin and resin cement colors

NARCIS (Netherlands)

Dozic, A.; Tsagkari, M.; Khashayar, G.; Aboushelib, M.

2010-01-01

Objective: Porcelain veneers have become an interesting treatment option to correct the shape and color of anterior teeth. Because of their limited thickness and high translucency, achieving a good color match is influenced by several variables. The aim of this work was to investigate the influence

Effect of quartz sand replacement by agate rejects in triaxial porcelain

International Nuclear Information System (INIS)

Correia, Sivaldo L.; Dienstmann, Gracieli; Folgueras, Marilena V.; Segadaes, Ana M.

2009-01-01

The ceramics industry, given the high volume of materials processed, stands as one of the largest consumers of natural raw materials but has also the capacity and potential to make significant contributions to solving environmental problems associated with other industries rejects. This work investigates the effects of quartz sand replacement by agate rejects (scrap) in a traditional triaxial porcelain composition. The study was carried out using the design of experiments (DoE) method. Characterization results were used to calculate statistically significant and valid regression equations, relating dried and fired body properties with clay, feldspar and agate scrap contents in the unfired mixture. The regression models were then discussed against X-ray diffraction and scanning electron microscopy results and used simultaneously to delimit the combinations of those three raw materials most adequate to produce a porcelainized stoneware floor tile with specified properties. Thus, an alternative use of an otherwise waste material is proposed, which can be translated into economic benefits and an important and welcome relief on environmental and waste disposal concerns

Characterization of kaolin and granite waste for formulation of porcelain stoneware tiles

International Nuclear Information System (INIS)

Luna da Silveira, G.C.; Acchar, W.; Gomes, U.U.; Silva, B.K.O.; Luna da Silveira, R.V.; Labrincha, J.A.; Costa, M.C.P.

2016-01-01

To produce a stoneware tiles is necessary develop a formulation that satisfies their structural characteristics, micro-structural, physical and mechanical properties. Thus, in order to create a formulation for porcelain stoneware tiles that give use to kaolin and granite waste used in the production of ceramic materials were asked the following characterizations: chemical analysis, mineralogical, thermal and particle size. We found that in the kaolin sample it presents a rate of silicon oxide and aluminum oxide similar to those found in the work of other investigators, about 45.23% SiO2 and 37.39% Al_2O_3. In the granite waste, the percentage of silicon oxide and aluminum oxide are also similar to those observed in other studies, with about 74.89% SiO2 and 10.54% Al_2O_3. Both the percentage of SiO_2 and Al_2O_3 founded in these two samples satisfy the percentage required in the manufacturing of porcelain stoneware tiles. (author)

Illustration of compositional variations over time of Chinese porcelain glazes combining micro-X-ray Fluorescence spectrometry, multivariate data analysis and Seger formulas

Science.gov (United States)

Van Pevenage, J.; Verhaeven, E.; Vekemans, B.; Lauwers, D.; Herremans, D.; De Clercq, W.; Vincze, L.; Moens, L.; Vandenabeele, P.

2015-01-01

In this research, the transparent glaze layers of Chinese porcelain samples were investigated. Depending on the production period, these samples can be divided into two groups: the samples of group A dating from the Kangxi period (1661-1722), and the samples of group B produced under emperor Qianlong (1735-1795). Due to the specific sample preparation method and the small spot size of the X-ray beam, investigation of the transparent glaze layers is enabled. Despite the many existing research papers about glaze investigations of ceramics and/or porcelain ware, this research reveals new insights into the glaze composition and structure of Chinese porcelain samples. In this paper it is demonstrated, using micro-X-ray Fluorescence (μ-XRF) spectrometry, multivariate data analysis and statistical analysis (Hotelling's T-Square test) that the transparent glaze layers of the samples of groups A and B are significantly different (95% confidence level). Calculation of the Seger formulas, enabled classification of the glazes. Combining all the information, the difference in composition of the Chinese porcelain glazes of the Kangxi period and the Qianlong period can be demonstrated.

Evolutionary morphology of the organ systems in squat lobsters and porcelain crabs (crustacea: Decapoda: Anomala): an insight into carcinization.

Science.gov (United States)

Keiler, Jonas; Richter, Stefan; Wirkner, Christian S

2015-01-01

Porcelain crabs (Porcellanidae) are one of three taxa within anomuran crustaceans (Anomala) which possess a crab-like body form. Curiously, these three lineages evolved this shape independently from true crabs (Brachyura) in the course of the evolutionary process termed carcinization. The entire pleon in porcelain crabs is flexed under the cephalothorax and the carapace is approximately as broad as long. Despite their crab-like habitus, porcelain crabs are phylogenetically nested within squat lobsters (Munidopsidae, Munididae, Galatheidae). With a pleon which is only partly flexed under the cephalothorax and a cephalothorax which is longer than it is broad, squat lobsters represent morphologically intermediate forms between lobster-like and crab-like body shapes. Carcinization has so far mostly been studied with respect to outer morphology; however, it is evident that internal anatomical features are influenced through this change of body shape too. In this paper, the situation in Galatheoidea is elucidated by adding more taxa to existing descriptions of the hemolymph vascular systems and associated structures and organs. Micro-computer tomography and 3D reconstruction provide new insights. Autapomorphic states of various internal anatomical characters are present in nearly all the studied species, also reflecting some degree of anatomical disparity found within Galatheoidea. The ventral vessel system of porcelain crabs differs distinctly from that of squat lobsters. The differences in question are coherent (i.e. structural dependent) with morphological transformations in the integument, such as the shortening of the sternal plastron, which evolved in the course of carcinization. Shifts in the gonads and the pleonal neuromeres are coherent with the loss of the caridoid escape reaction, which in turn is a consequence of carcinization. The arterial transformations, however, are minor compared to other instances of carcinization in anomuran crustaceans since the last

The TAC of porcelain samples and its influence on TL dating

International Nuclear Information System (INIS)

Leung, P.L.; Stokes, M.J.; Xia Junding; Wang Weida

1997-01-01

The thermal activation characteristics of porcelain slice samples for pre-dose dating were obtained by using the multiple activation method. The influence of activation temperature on TL dating was also studied. The results show that choosing a temperature corresponding to the maximum sensitivity on the TAC curve as the activation temperature is very important in the multiple activation method

[Effect of sandblasting particle sizes on bonding strength between porcelain and titanium fabricated by rapid laser forming].

Science.gov (United States)

Zhang, Li-jun; Wang, Zhong-yi; Gao, Bo; Gao, Yang; Zhang, Chun-bao

2009-11-01

To evaluate the effect of sandblasting particle sizes of Al2O3 on the bonding strength between porcelain and titanium fabricated by laser rapid forming (LRF). The thermal expansion coefficient, roughness (Ra), contact angle, surface morphology of titanium surface and the bonding strength between titanium and porcelain were evaluated after the titanium surface being sandblasted using different sizes of Al2O3 (50 microm, 120 microm, 250 microm) at a pressure of 0.5 MPa. The cast titanium specimens were used as control, and were sandblasted with 50 microm Al2O3 at the same pressure. The thermal expansion coefficient of cast titanium [(9.84 +/- 0.42) x 10(-6)/ degrees C] and LRF Ti [(9.79 +/- 0.31) x 10(-6)/ degrees C) matched that of Noritake Ti-22 dentin porcelain [(8.93 +/- 0.36) x 10(-6)/ degrees C). When larger size of Al2O3 was used, the value of Ra and contact angle increased as well. There was no significant difference in bonding strength between the LRF Ti-50 microm [(25.91 +/- 1.02) MPa] and cast titanium [(26.42 +/- 1.65) MPa]. Significantly lower bonding strength was found in LRF Ti-120 microm [(21.86 +/- 1.64) MPa] and LRF Ti-250 microm [(19.96 +/- 1.03) MPa]. The bond strength between LRF Ti and Noritake Ti-22 dentin porcelain was above the lower limit value in the ISO 9693 (25 MPa) after using 50 microm Al2O3 sandblasting in 0.5MPa air pressure.

Dosimetry of accidents using thermoluminescence of dental restorative porcelains

International Nuclear Information System (INIS)

Mauricio, C.L.P.; Rosa, L.A.R. da; Cunha, P.G. da

1986-01-01

The thermoluminescence (TL) properties of dental restorative porcelain were investigated with the aim of using this material as a TL dosemeter to estimate high doses in radiological accidents. The irradiations were carried out with a 60 Co gamma source and X rays with effective energies from 29 to 95 KeV. The samples have a limit of detection at about 50R and their reproducibility is better than 15%. Linearity was observed from 50 to 5000R. (Author) [pt

Preparation of porcelain tile granulates by more environmentally sustainable processes

Directory of Open Access Journals (Sweden)

García-Ten, J.

2012-04-01

Full Text Available This study examines the feasibility of manufacturing glazed porcelain tiles with a more environmentally friendly manufacturing process, by reducing water and thermal energy consumption. The process studied in this paper is dry milling in a pendulum mill, with subsequent granulation (in order to obtain a press powder with similar flowability to that of spraydried powders. The different morphology of the new granulate with respect to the standard spray-dried granulate modifies the microstructure of the green compacts and thus, their behaviour and fired tile properties. In order to obtain porcelain tiles with the required properties (water absorption, mechanical strength,… changes have been made in the raw materials mixture and in the processing variables. Finally, porcelain tiles measuring 50x50 cm have been manufactured at industrial scale with the new granulate using a conventional firing cycle, obtaining quality levels identical to those provided by the spray-dried granulate. These results open the possibility of preparing porcelain tile body compositions through a manufacturing process alternative to the standard one, more environmentally friendly and with lower costs.

En el presente trabajo se ha estudiado la viabilidad de fabricar gres porcelánico esmaltado utilizando un sistema de preparación de la composición del soporte más respetuoso con el medio ambiente, lo que implica una reducción importante de los consumos de agua y de energía térmica. El proceso que se estudia en el presente trabajo es el consistente en la molienda vía seca en molino pendular y en la posterior granulación (para obtener un polvo de prensas con fluidez similar a la de los polvos atomizados. La distinta morfología de los nuevos gránulos obtenidos respecto al polvo atomizado actual, modifica la microestuctura en crudo de las piezas y, con ello, el comportamiento y propiedades finales de las baldosas obtenidas. Por ello, ha sido necesario

Marker-assisted introgression of opaque2 allele for rapid conversion ...

Indian Academy of Sciences (India)

Firoz Hossain

2018-03-15

Mar 15, 2018 ... of total calorie to the human populations worldwide. ... A major portion (60–70%) of maize ... endosperm protein is, however, known to be poor in nutri- ... turns out to be the most sustainable and cost-effective solu- .... For MABB (figure 1), recurrent parents (as females) and ... indicating per cent opaqueness.

Real-Time Amplitude and Phase Imaging of Optically Opaque Objects by Combining Full-Field Off-Axis Terahertz Digital Holography with Angular Spectrum Reconstruction

Science.gov (United States)

Yamagiwa, Masatomo; Ogawa, Takayuki; Minamikawa, Takeo; Abdelsalam, Dahi Ghareab; Okabe, Kyosuke; Tsurumachi, Noriaki; Mizutani, Yasuhiro; Iwata, Testuo; Yamamoto, Hirotsugu; Yasui, Takeshi

2018-06-01

Terahertz digital holography (THz-DH) has the potential to be used for non-destructive inspection of visibly opaque soft materials due to its good immunity to optical scattering and absorption. Although previous research on full-field off-axis THz-DH has usually been performed using Fresnel diffraction reconstruction, its minimum reconstruction distance occasionally prevents a sample from being placed near a THz imager to increase the signal-to-noise ratio in the hologram. In this article, we apply the angular spectrum method (ASM) for wavefront reconstruction in full-filed off-axis THz-DH because ASM is more accurate at short reconstruction distances. We demonstrate real-time phase imaging of a visibly opaque plastic sample with a phase resolution power of λ/49 at a frame rate of 3.5 Hz in addition to real-time amplitude imaging. We also perform digital focusing of the amplitude image for the same object with a depth selectivity of 447 μm. Furthermore, 3D imaging of visibly opaque silicon objects was achieved with a depth precision of 1.7 μm. The demonstrated results indicate the high potential of the proposed method for in-line or in-process non-destructive inspection of soft materials.

Real-Time Amplitude and Phase Imaging of Optically Opaque Objects by Combining Full-Field Off-Axis Terahertz Digital Holography with Angular Spectrum Reconstruction

Science.gov (United States)

Yamagiwa, Masatomo; Ogawa, Takayuki; Minamikawa, Takeo; Abdelsalam, Dahi Ghareab; Okabe, Kyosuke; Tsurumachi, Noriaki; Mizutani, Yasuhiro; Iwata, Testuo; Yamamoto, Hirotsugu; Yasui, Takeshi

2018-04-01

Terahertz digital holography (THz-DH) has the potential to be used for non-destructive inspection of visibly opaque soft materials due to its good immunity to optical scattering and absorption. Although previous research on full-field off-axis THz-DH has usually been performed using Fresnel diffraction reconstruction, its minimum reconstruction distance occasionally prevents a sample from being placed near a THz imager to increase the signal-to-noise ratio in the hologram. In this article, we apply the angular spectrum method (ASM) for wavefront reconstruction in full-filed off-axis THz-DH because ASM is more accurate at short reconstruction distances. We demonstrate real-time phase imaging of a visibly opaque plastic sample with a phase resolution power of λ/49 at a frame rate of 3.5 Hz in addition to real-time amplitude imaging. We also perform digital focusing of the amplitude image for the same object with a depth selectivity of 447 μm. Furthermore, 3D imaging of visibly opaque silicon objects was achieved with a depth precision of 1.7 μm. The demonstrated results indicate the high potential of the proposed method for in-line or in-process non-destructive inspection of soft materials.

Edge forward mechanical protection for porcelain insulators

Energy Technology Data Exchange (ETDEWEB)

deCasseres, D.K.

1987-12-01

Vandal damage to exposed outdoor insulators of all types has become an increasing problem. Porcelain is susceptible to impact fracture, and Area Boards have frequently found it necessary to protect expensive and often highly vulnerable terminating assemblies from the unwelcome attention of hooligans. Various means of physical protection can be used, but many of these are highly demanding in terms of maintenance. This article discusses the 'state of the art' in insulator protection, and describes the design and development of a new concept in the field-the Shed Protector-a number of which are now installed on 132kV sealing ends throughout the Electricity Supply Industry.

The infrared stage Linkam FTIR 600 for microthermometric studies in dark and opaque minerals associated to uranium mineralization

International Nuclear Information System (INIS)

Lima, Tatiana Aparecida Fernandes de; Rios, Francisco Javier; Fuzikawa, Kazuo; Oliveira, Lucilia A. Ramos de; Oliveira, Elizabeth Kerpe; Neves, Jose Marques Correia; Prates, Sonia Pinto

2009-01-01

Fluid composition studies, throughout fluid inclusions (FI), contribute to improve the understanding of mineral deposits. FI correspond to small portions of fluids trapped in minerals by many processes that preserve relevant information related to fluid composition which forms ore deposits. Microscopy and microthermometry techniques applied to fluid inclusions studies of opaque and/or dark minerals use infrared light (IR). A specific stage heating/cooling that allows working in the near infrared (NIR). Thus, the infrared stage model FTIR600 Linkam coupled the IR OLYMPUS BX51, with the automatic controllers LNP 94/2 and TMS 94, and software Linksys 32 - Linkam installed in computer was implemented and tested. An infrared QUICAM fast 1394 QIMAGING TM camera with the program QCAPTURE SUITE was acquisition for images capture and adapted the new system. This infrared stage Linkam FTIR600 reach temperatures between -196 deg C to +600 deg C, with the differential of working in the NIR; it is all automated, obtaining computerized data, graphics in real time of analysis and storage the data. It also controls the speed of the experiment (up to 130 deg C/min); it runs consecutively heating and cooling with a small N 2 (l) consuming; besides greater results repeatability, obtaining accurate and precise temperatures. Actually the Linkam stage FTIR600 is operating in the Metallogenesis and Fluid Inclusions Laboratory (LIFM) at CDTN/CNEN. Uranium ore and/or others mineralization studies which shows dark or opaque mineral have been developed. The uranium mineralization in the Lagoa Real Uraniferous Province, Bahia, Brazil, shows several rock-forming minerals together with the dark and opaque minerals (garnet, magnetite, pyroxene) emphasized in the present work. (author)

Enhanced ion acceleration in transition from opaque to transparent plasmas

Science.gov (United States)

Mishra, R.; Fiuza, F.; Glenzer, S.

2018-04-01

Using particle-in-cell simulations, we investigate ion acceleration in the interaction of high intensity lasers with plasmas which transition from opaque to transparent during the interaction process. We show that the highest ion energies are achieved when the laser traverses the target around the peak intensity and re-heats the electron population responsible for the plasma expansion, enhancing the corresponding sheath electric field. This process can lead to an increase of up to 2x in ion energy when compared with the standard Target Normal Sheath Acceleration in opaque targets under the same laser conditions. A theoretical model is developed to predict the optimal target areal density as a function of laser intensity and pulse duration. A systematic parametric scan for a wide range of target densities and thicknesses is performed in 1D, 2D and 3D and shown consistent with the theory and with recent experimental results. These results open the way for a better optimization of the ion energy in future laser–solid experiments.

An assessment of the quality of liquid effluents from opaque beer ...

African Journals Online (AJOL)

driniev

2005-01-01

Jan 1, 2005 ... The effluent treatment plants in both plants were not only inadequate but also ... Keywords: industrial effluents, opaque beer-brewery, pollution load, quality, quantity ... to hydraulic overloading and corrosion of the sewer pipe system ... The two breweries studied in this paper produce African traditional.

Further studies on gold alloys used in fabrication of porcelain-fused-to-metal restorations.

Science.gov (United States)

Civjan, S; Huget, E F; Dvivedi, N; Cosner, H J

1975-03-01

Composition, microstructure, castability, mechanical properties, and heat treatment characteristics of two gold-palladium-silver-based alloys were studied. The materials exhibited compositional as well as microstructural differences. Clinically acceptable castings could not be obtained when manufacturers' recommended casting temperatures were used. Ultimate tensile strength, yield strength, modulus of elasticity, and Brinell hardness values for the alloys were comparable. The elastic limit of Cameo, however, was significantly higher than that of vivo-star. Maximum rehardening of annealed castings occurred on reheat treatment at temperatures between 1,200 and 1,300 F. As-cast specimens, however, were not heat hardenable. The sequence of heat treatments used in the application of porcelain reduced slightly the hardness of both alloys. Hardness of the metal substructures was not increased by return of porcelain-coated specimens to a 1,250 F oven for final heat treatment.

Porcelainized stoneware: architectural, processing and physico-mechanical properties

Directory of Open Access Journals (Sweden)

Manfredini, T.

1996-06-01

Full Text Available Porcelainized stoneware is an extremely hard and homogeneous unglazed ceramic material obtained by fastfiring of kaolinitic ceramic bodies containing a large amount of fluxes. The obtained tiles, available in a large variety of colours, shape size and surface finish, are characterized by very low porosity (<0,3wt% expressed as water absorption and are ideal for heavy-traffic areas subject to mechanical and chemical stresses. Porcelainized stoneware tiles offer alternative valid (and in many cases necessary solutions to the traditional glazed tiles either for interiors or for exteriors both in modern or classic constructions for flooring and covering.

El gres porcelánico es un material cerámico muy duro y homogéneo, no vidriado en su superficie, obtenido por cocción rápida de composiciones ricas en caolinita, conteniendo una gran cantidad de fundentes. Las plaquetas de pavimentos que se obtienen son de una variedad muy extensa en aspectos, diseños y colores, caracterizándose, fundamentalmente, por su muy baja porosidad (<0,3wt%, expresado en porcentaje de capacidad de absorción de agua. Estos materiales son ideales para tráfico pesado en áreas sujetas a intensas tensiones mecánicas y químicas. El gres porcelánico ofrece alternativas válidas (y, en muchos casos, soluciones necesarias a los pavimentos vidriados tradicionales, en interiores o para usos exteriores, ambos con decoraciones modernas o clásicas para suelos o recubrimientos de paredes.

Microstructure Study For Optimization Of Dielectric Property Of Electrical Porcelain

International Nuclear Information System (INIS)

Tak, S. K.; Shekhawat, M. S.; Mangal, R.

2010-01-01

Five sample mixtures of kaolin, ball clay, feldspar and Quartz were formulated and porcelain samples fabricated. Crystalline phases and mullite morphology were studied using XRD and SEM respectively. A composition of 30% kaolin, 15% ball clay, 30% feldspar and 25% quartz yielded a body with high dielectric strength of 19 kV/mm compare to an ISO graded product having dielectric strength 14.6 KV/mm after firing at 1225 deg. C.

Digital in-line holography assessment for general phase and opaque particle

NARCIS (Netherlands)

Coëtmellec, S.; Wichitwong, W.; Gréhan, G.; Lebrun, D.; Brunel, M.; Janssen, A.J.E.M.

2014-01-01

We propose using the circle polynomials to describe a particle’s transmission function in a digital holography setup. This allows both opaque and phase particles to be determined. By means of this description, we demonstrate that it is possible to estimate the digital in-line hologram produced by a

Neutron activation analysis of bulk samples from Chinese ancient porcelain to provenance research

International Nuclear Information System (INIS)

Jian Zhu; Wentao Hao; Jianming Zhen; Tongxiu Zhen; Glascock, M.D.

2013-01-01

Neutron activation analysis (NAA) is an important technique to determine the provenance of ancient ceramics. The most common technique used for preparing ancient samples for NAA is to grind them into a powder and then encapsulate them before neutron irradiation. Unfortunately, ceramic materials are typically very hard making it a challenge to grind them into a powder. In this study we utilize bulk porcelain samples cut from ancient shards. The bulk samples are irradiated by neutrons alongside samples that have been conventionally ground into a powder. The NAA for both the bulk samples and powders are compared and shown to provide equivalent information regarding their chemical composition. Also, the multivariate statistical have been employed to the analysis data for check the consistency. The findings suggest that NAA results are less dependent on the state of the porcelain sample, and thus bulk samples cut from shards may be used to effectively determine their provenance. (author)

[Effect of TiO2-SiO2-SnOx film with different firing temperatures on bond strength of low-fusing dental porcelain to pure titanium].

Science.gov (United States)

Zhang, Zichuan; Zhang, Pei

2015-07-01

To evaluate the influence of TiO(2)-SiO(2)-SnOx nano-coatings with different firing temperatures on the bond strength of low-fusing dental porcelain to pure titanium. The surface of pure titanium was coated uniformly with TiO(2)-SiO(2)-SnOx nano-coatings by solution-gelatin (Sol-Gel) technology and then fired at 300 °C (group A) or 750 °C (group B) for 1 h. The specimens without any coatings were the control group (group C). There were 10 specimens in each group. Dental porcelain was sintered on the surface of titanium specimens. Surface roughness and contact angle of the coatings were also detected. The titanium-porcelain bond strength was investigated according to YY 0621-2008 standards using three-point flexure bond test. The phase composition of the TiO(2)-SiO(2)-SnOx nano-coatings was characterized by X-ray diffraction(XRD). The interface of titanium-porcelain and TiO(2)-SiO(2)-SnOx nano-coatings were observed using scanning electron microscope (SEM). No rutile phase was found in these specimens of group A and group B. The surface roughness of group A, B, C was (0.97 ± 0.06), (0.99 ± 0.03), (0.96 ± 0.07) µm, respectively. No significant difference was found among the three groups. Compared with that of group C (64.37° ± 3.01°), contact angles detected in group A (52.04° ± 3.15°) and group B (85.27° ± 4.17°) were significantly different (P porcelain in group A [(35.66 ± 2.65) MPa] was significantly increased compared with those in group B [(26.18 ± 2.22) MPa] and group C [(31.66 ± 3.52) MPa]. SEM photomicrographs of titanium-porcelain interface morphology of the specimens before porcelain sintering showed that TiO(2)-SiO(2)-SnOx nano-coatings in group A were compact and homogeneous with petty cracks and those in group B was loose and arranged disorderly. TiO(2)-SiO(2)-SnOx nano-coating fired at 300 °C is significantly effective in improving the titanium-porcelain bond strength.

Chinese porcelain and other orientalia and exotica in Spain during the Habsburg Dynasy

NARCIS (Netherlands)

Krahe, Cinta

2014-01-01

The reception of Chinese and Japanese export porcelain in Europe and the Americas has been the subject of much research, many publications and a number of exhibitions. The scholars and researchers involved could base themselves on a solid corpus of data, gathered in the past from a miscellany of

Evaluation of the mechanical properties and porcelain bond strength of cobalt-chromium dental alloy fabricated by selective laser melting.

Science.gov (United States)

Wu, Lin; Zhu, Haiting; Gai, Xiuying; Wang, Yanyan

2014-01-01

Limited information is available regarding the microstructure and mechanical properties of dental alloy fabricated by selective laser melting (SLM). The purpose of this study was to evaluate the mechanical properties of a cobalt-chromium (Co-Cr) dental alloy fabricated by SLM and to determine the correlation between its microstructure and mechanical properties and its porcelain bond strength. Five metal specimens and 10 metal ceramic specimens were fabricated to evaluate the mechanical properties of SLM Co-Cr dental alloy (SLM alloy) with a tensile test and its porcelain bond strength with a 3-point bending test. The relevant properties of the SLM alloy were compared with those of the currently used Co-Cr dental alloy fabricated with conventional cast technology (cast alloy). The Student t test was used to compare the results of the SLM alloy and the cast alloy (α=.05). The microstructure of the SLM alloy was analyzed with a metallographic microscope; the metal ceramic interface of the SLM porcelain bonded alloy was studied with scanning electron microscopy, energy dispersive x-ray spectroscopy, and an electron probe microanalyzer. Both the mean (standard deviation) yield strength (884.37 ± 8.96 MPa) and tensile strength (1307.50 ±10.65 MPa) of the SLM alloy were notably higher than yield strength (568.10 ± 30.94 MPa) and tensile strength (758.73 ± 25.85 MPa) of the currently used cast alloy, and the differences were significant (P.05). Microstructure analysis suggested that the SLM alloy had a dense and obviously orientated microstructure, which led to excellent mechanical properties. Analysis from scanning electron microscopy, energy dispersive x-ray spectroscopy, and the electron probe microanalyzer indicated that the SLM alloy had an intermediate layer with elemental interpenetration between the alloy and the porcelain, which resulted in an improved bonding interface. Compared with the currently used cast alloy, SLM alloy possessed improved mechanical

[Influence of different surface treatments on porcelain surface topography].

Science.gov (United States)

Tai, Yinxia; Zhu, Xianchun; Sen, Yan; Liu, Chang; Zhang, Xian; Shi, Xueming

2013-02-01

To evaluate the influence of different surface treatments on porcelain surface topography. Metal ceramic prostheses in 6 groups were treated according to the different surface treatment methods, and the surface topography was observed through scanning electron microscope (SEM). Group A was the control one (untreated), group B was etched by 9.6% hydrofluoric acid(HF), group C was deglazed by grinding and then etched by 9.6% HF, group D was treated with Nd: YAG laser irradiation(0.75 W) and HF etching, group E was treated with Nd: YAG laser irradiation (1.05 W) and HF etching, and group F was treated with laser irradiation (1.45 W) and HF etching. Surface topography was different in different groups. A lot of inerratic cracks with the shapes of rhombuses and grid, and crater with a shape of circle were observed on the ceramic surface after treatment with energy parameters of 1.05 W Nd: YAG laser irradiation and 9.6% HF etching (group E). Surface topography showed a lot of concaves on the inner wall of the cracks, and the concaves with diameter of 1-5 microm could be observed on the inner wall of the holes, which had a diameter of 20 microm under SEM. The use of Nd: YAG laser irradiation with the energy parameters of 1.05 W and the HF with a concentration of 9.6% can evenly coarsen the porcelain surface, that is an effective surface treatment method.

A comparative transmission electron microscopy, energy dispersive x-ray spectroscopy and spatially resolved micropillar compression study of the yttria partially stabilised zirconia - porcelain interface in dental prosthesis

Energy Technology Data Exchange (ETDEWEB)

Lunt, Alexander J.G., E-mail: alexander.lunt@chch.ox.ac.uk [Department of Engineering Science, University of Oxford, Parks Road, Oxford, Oxfordshire OX1 3PJ (United Kingdom); Mohanty, Gaurav, E-mail: gaurav.mohanty@empa.ch [EMPA Materials Science & Technology, Feuerwerkerstrasse 39, CH-3602 Thun (Switzerland); Ying, Siqi, E-mail: siqi.ying@eng.ox.ac.uk [Department of Engineering Science, University of Oxford, Parks Road, Oxford, Oxfordshire OX1 3PJ (United Kingdom); Dluhoš, Jiří, E-mail: jiri.dluhos@tescan.cz [TESCAN Brno, s.r.o., Libušina tř. 1, 623 00 Brno-Kohoutovice (Czech Republic); Sui, Tan, E-mail: tan.sui@eng.ox.ac.uk [Department of Engineering Science, University of Oxford, Parks Road, Oxford, Oxfordshire OX1 3PJ (United Kingdom); Neo, Tee K., E-mail: neophyte@singnet.com.sg [Specialist Dental Group, Mount Elizabeth Orchard, 3 Mount Elizabeth, #08-03/08-08/08-10, 228510 (Singapore); Michler, Johann, E-mail: johann.michler@empa.ch [EMPA Materials Science & Technology, Feuerwerkerstrasse 39, CH-3602 Thun (Switzerland); Korsunsky, Alexander M., E-mail: alexander.korsunsky@eng.ox.ac.uk [Department of Engineering Science, University of Oxford, Parks Road, Oxford, Oxfordshire OX1 3PJ (United Kingdom)

2015-12-01

Recent studies into the origins of failure of yttria partially stabilised zirconia–porcelain veneered prosthesis have revealed the importance of micro-to-nano scale characterisation of this interface zone. Current understanding suggests that the heat treatment, residual stresses and varying microstructure at this location may contribute to near-interface porcelain chipping. In this study the chemical, microstructural and mechanical property variation across the interfacial zone has been characterised at two differing length scales and using three independent techniques; energy dispersive X-ray spectroscopy, transmission electron microscopy and micropillar compression. Energy dispersive X-ray spectroscopy mapping of the near-interface region revealed, for the first time, that the diffusional lengths of twelve principal elements are limited to within 2–6 μm of the interface. This study also revealed that 0.2–2 μm diameter zirconia grains had become detached from the bulk and were embedded in the near-interface porcelain. Transmission electron microscopy analysis demonstrated the presence of nanoscale spherical features, indicative of tensile creep induced voiding, within the first 0.4–1.5 μm from the interface. Within zirconia, variations in grain size and atomistic structure were also observed within the 3 μm closest to the interface. Micropillar compression was performed over a 100 μm range on either side of the interface at the spatial resolution of 5 μm. This revealed an increase in zirconia and porcelain loading modulus at close proximities (< 5 μm) to the interface and a decrease in zirconia modulus at distances between 6 and 41 μm from this location. The combination of the three experimental techniques has revealed intricate details of the microstructural, chemical and consequently mechanical heterogeneities in the YPSZ–porcelain interface, and demonstrated that the length scales typically associated with this behaviour are approximately ± 5

TECHNOLOGICAL TESTS USING QUARTZITE RESIDUES AS COMPONENT OF CERAMIC MASS AT THE PORCELAIN STONEWARE PRODUCTION

Directory of Open Access Journals (Sweden)

Marcondes Mendes Souza

2015-03-01

Full Text Available This work aims to evaluate through technological tests the use of quartzite residues as component at the the production of porcelain stoneware. Were collected five samples of quartzites called of green quartzite, black quartzite, pink quartzite, goldy quartzite, white quartzite. After, the raw materials were milled, passed by a sieve with a Mesh of 200# (Mesh and characterized by chemical analysis in fluorescence of x-rays and also analysis of the crystalline phases by diffraction of x-rays. The porcelain tiles mass is composed of five formulations containing 57% of feldspar, 37% of clay and 6% of residues of quartzite with different coloration. For the preparation of the specimens, it was used uniaxial pressing, which afterwards were synthesized at 1150°C, 1200°C and 1250°C. After the sintering, the specimens were submit for tests of technological characterization like: water absorption, linear shrinkage, apparently porosity, density and flexural strain at three points. The results presented in the fluorescence of x-rays showed a high-content of iron oxide on black quartzite that is why it was discarded the utilization of it in porcelain stoneware. All quartzite formulations had low water absorption achieved when synthesized at 1200°C, getting 0.1 to 0.36% without having gone through the atomization process. At the tests of flexural strain, all the quartzite had in acceptance limits, according to the European norm EN 100, overcoming 27 MPA at 1200°C

Four chemical methods of porcelain conditioning and their influence over bond strength and surface integrity

Science.gov (United States)

Stella, João Paulo Fragomeni; Oliveira, Andrea Becker; Nojima, Lincoln Issamu; Marquezan, Mariana

2015-01-01

OBJECTIVE: To assess four different chemical surface conditioning methods for ceramic material before bracket bonding, and their impact on shear bond strength and surface integrity at debonding. METHODS: Four experimental groups (n = 13) were set up according to the ceramic conditioning method: G1 = 37% phosphoric acid etching followed by silane application; G2 = 37% liquid phosphoric acid etching, no rinsing, followed by silane application; G3 = 10% hydrofluoric acid etching alone; and G4 = 10% hydrofluoric acid etching followed by silane application. After surface conditioning, metal brackets were bonded to porcelain by means of the Transbond XP system (3M Unitek). Samples were submitted to shear bond strength tests in a universal testing machine and the surfaces were later assessed with a microscope under 8 X magnification. ANOVA/Tukey tests were performed to establish the difference between groups (α= 5%). RESULTS: The highest shear bond strength values were found in groups G3 and G4 (22.01 ± 2.15 MPa and 22.83 ± 3.32 Mpa, respectively), followed by G1 (16.42 ± 3.61 MPa) and G2 (9.29 ± 1.95 MPa). As regards surface evaluation after bracket debonding, the use of liquid phosphoric acid followed by silane application (G2) produced the least damage to porcelain. When hydrofluoric acid and silane were applied, the risk of ceramic fracture increased. CONCLUSIONS: Acceptable levels of bond strength for clinical use were reached by all methods tested; however, liquid phosphoric acid etching followed by silane application (G2) resulted in the least damage to the ceramic surface. PMID:26352845

Does Opaqueness Make Equity Capital Expensive for Banks?

Directory of Open Access Journals (Sweden)

Karlo Kauko

2014-12-01

Full Text Available Bank managers often claim that equity is expensive, which contradicts the Modigliani-Miller irrelevance theorem. An opaque bank must signal its solvency by paying high and stable dividends in order to keep depositors tranquil. This signalling may require costly liquidations if the return on assets has been poor, but not paying the dividend might trigger a run. A strongly capitalized bank should keep substantial amounts of risk-free yet non-productive currency because the number of shares is high, which is costly. The dividend is informative of the state of the bank; rational depositors react to it.

Bonding of Metal Orthodontic Attachments to Sandblasted Porcelain and Zirconia Surfaces

Directory of Open Access Journals (Sweden)

Amitoj S. Mehta

2016-01-01

Full Text Available This study evaluates tensile bond strength (TBS of metal orthodontic attachments to sandblasted feldspathic porcelain and zirconia with various bonding protocols. Thirty-six (36 feldspathic and 36 zirconia disc samples were prepared, glazed, embedded in acrylic blocks and sandblasted, and divided into three groups according to one or more of the following treatments: hydrofluoric acid 4% (HF, Porcelain Conditioner silane primer, Reliance Assure® primer, Reliance Assure plus® primer, and Z Prime™ plus zirconia primer. A round traction hook was bonded to each sample. Static tensile bond strength tests were performed in a universal testing machine and adhesive remnant index (ARI scoring was done using a digital camera. One-way ANOVA and Pearson chi-square tests were used to analyze TBS (MPa and ARI scores. No statistically significant mean differences were found in TBS among the different bonding protocols for feldspathic and zirconia, p values = 0.369 and 0.944, respectively. No statistically significant distribution of ARI scores was found among the levels of feldspathic, p value = 0.569. However, statistically significant distribution of ARI scores was found among the levels of zirconia, p value = 0.026. The study concluded that silanization following sandblasting resulted in tensile bond strengths comparable to other bonding protocols for feldspathic and zirconia surface.

OPAQUE MINERAL CONTENT OF DUTLUCA VOLCANICS (BURHANİYE - BALIKESİR: THE EFFECT OF HYDROTHERMAL ALTERATION ON THESE MINERALS

Directory of Open Access Journals (Sweden)

Şükrü KOÇ

2016-12-01

Full Text Available Dutluca volcanics, which are known as Hallaçlar Formation in regional scale in the study area (Kurshens- ky, 1976, are composed of hydrothermally altered andesite and basaltic andesite. In these rocks, sulfidic minerals such as pyrite, enargite and chalcosine, and oxide and hydroxide minerals such as magnetite, hematite and goethite were detected as opaque minerals. The presence of enargite in opaque mineral para- genesis, and the changes observed in structures and textures of opaque and silicate minerals indicate that examined volcanics have been altered by highly sulfidic hydrothermal solutions. During the hydrothermal alteration process, which indicates at least in two phases, a diffuse pyritization rich in H S in reducing conditions and enargite mineral, which is known as pathfinder minerals in such processes, formed in the first phase. Later on; the extensive martitization developed in oxidizing conditions.

The effect of simulating porcelain firing on the elemental composition, microstructure, and mechanical properties of electroformed gold restorations

Directory of Open Access Journals (Sweden)

Youssef S. Al Jabbari

2016-09-01

Conclusion: Although microstructure and elemental composition of electroformed Au crowns remain unchanged, the mechanical properties are significantly affected by the thermal treatment of porcelain firing.

Interfacial characterization of ceramic core materials with veneering porcelain for all-ceramic bi-layered restorative systems.

Science.gov (United States)

Tagmatarchis, Alexander; Tripodakis, Aris-Petros; Filippatos, Gerasimos; Zinelis, Spiros; Eliades, George

2014-01-01

The aim of the study was to characterize the elemental distribution at the interface between all-ceramic core and veneering porcelain materials. Three groups of all-ceramic cores were selected: A) Glass-ceramics (Cergo, IPS Empress, IPS Empress 2, e-max Press, Finesse); B) Glass-infiltrated ceramics (Celay Alumina, Celay Zirconia) and C) Densely sintered ceramics (Cercon, Procera Alumina, ZirCAD, Noritake Zirconia). The cores were combined with compatible veneering porcelains and three flat square test specimens were produced for each system. The core-veneer interfaces were examined by scanning electron microscopy and energy dispersive x-ray microanalysis. The glass-ceramic systems showed interfacial zones reach in Si and O, with the presence of K, Ca, Al in core and Ca, Ce, Na, Mg or Al in veneer material, depending on the system tested. IPS Empress and IPS Empress 2 demonstrated distinct transitional phases at the core-veneer interface. In the glassinfiltrated systems, intermixing of core (Ce, La) with veneer (Na, Si) elements occurred, whereas an abrupt drop of the core-veneer elemental concentration was documented at the interfaces of all densely sintered ceramics. The results of the study provided no evidence of elemental interdiffusion at the core-veneer interfaces in densely sintered ceramics, which implies lack of primary chemical bonding. For the glass-containing systems (glassceramics and glass-infiltrated ceramics) interdiffusion of the glass-phase seems to play a critical role in establishing a primary bonding condition between ceramic core and veneering porcelain.

Tribological study of PTFE composites loaded with porcelain tile waste

International Nuclear Information System (INIS)

Oliveira, P.M.; Araujo Neto, A.P.; Souza, J.R.; Medeiros, J.T.N.

2016-01-01

The Brazilian northeast is one of the largest producers of clays that burn in the white form and disposal of tailings from the process of polishing the ceramic pieces of porcelain stands out as a major source of environmental degradation. This problem can be reduced by adding such material as filler in composites, in order to improve the mechanical properties of the polymeric matrix. Polytetrafluoroethylene (PTFE) is characterized as a good solid lubricant, because it has excellent properties such as low coefficient of friction (0.01 < μ < 0.1), thermal stability at high temperatures and chemical resistance. However, the pure PTFE has high wear rates (greater than 10-13m2/N) leading to early failures of various components. To reuse the Tailings of Porcelain (TP), composites of PTFE + TP were developed in three different compositions (85:15, 75:25 and 65:35). For this investigation the particle size distribution and some chemical characteristics of the tailings by testing XRD, XRF, SEM and EDS were performed, registering a large amount of silica, aluminum and other metals. Roughness, wettability and sclerometry also were performed. It was noted that the values of arithmetic average roughness, Ra, is higher for composites with higher percentage of TP, in addition they have a lower contact angle and higher surface energy to distilled water, characterized as hydrophilic. The results of energy of deformation provided by the sclerometry test were non-linear. (author)

Utilization of radiometric method in evaluation of wear on human dental enamel in vitro by dental porcelain glazed and polished; Utilizacao do metodo radiometrico na avaliacao in vitro do desgaste provocado ao esmalte dental humano por porcelanas dentais glazeadas e polidas

Energy Technology Data Exchange (ETDEWEB)

Adachi, Lena Katekawa; Campos, Tomie Nakakuki de; Adachi, Eduardo Makoto [Sao Paulo Univ., SP (Brazil). Faculdade de Odontologia. Dept. de Protese]. E-mail: katekawa@usp.br; Saiki, Mitiko [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)]. E-mail: mitiko@curiango.ipen.br

2005-07-01

The dental porcelain is a material commonly used in prosthesis. Disadvantages of dental porcelain use include possibility to cause tooth or dental materials wear. Before its use in the mouth, surfaces are treated with polishing and/or glazing. This research used the radiometric method to verify the influence of these surface treatments on the porcelains of commercial brands: Ceramco II, Noritake and Finesse. This method was originally developed for dentifrice abrasiveness evaluation. Five specimens of dental enamel and 10 specimens of each porcelain (5 glazed, 5 polished) were used. The dental enamel was flattened and irradiated with neutrons from the IEA-R1 (IPEN/CNEN) nuclear reactor. Then it was weared by each porcelain in sliding motion, with water. After 2,500 cycles for each porcelain specimen, the released enamel residue was measured. The enamel wear was evaluated by measuring beta activity of {sup 32}P transferred to water from the irradiated tooth. Results varied from 2.57 to 5.81 {mu}g of enamel /mm{sup 2} weared surface. There was no statistical difference ({alpha}=0.05) between dental enamel wear caused by the same porcelains glazed or polished. The results suggest that adequate surface finishing depend on the type of dental porcelain. (author)

Reflective small angle electron scattering to characterize nanostructures on opaque substrates

Science.gov (United States)

Friedman, Lawrence H.; Wu, Wen-Li; Fu, Wei-En; Chien, Yunsan

2017-09-01

Feature sizes in integrated circuits (ICs) are often at the scale of 10 nm and are ever shrinking. ICs appearing in today's computers and hand held devices are perhaps the most prominent examples. These smaller feature sizes demand equivalent advances in fast and accurate dimensional metrology for both development and manufacturing. Techniques in use and continuing to be developed include X-ray based techniques, optical scattering, and of course the electron and scanning probe microscopy techniques. Each of these techniques has their advantages and limitations. Here, the use of small angle electron beam scattering measurements in a reflection mode (RSAES) to characterize the dimensions and the shape of nanostructures on flat and opaque substrates is demonstrated using both experimental and theoretical evidence. In RSAES, focused electrons are scattered at angles smaller than 1 ° with the assistance of electron optics typically used in transmission electron microscopy. A proof-of-concept experiment is combined with rigorous electron reflection simulations to demonstrate the efficiency and accuracy of RSAES as a method of non-destructive measurement of shapes of features less than 10 nm in size on flat and opaque substrates.

Shear bond strength of metal brackets to feldspathic porcelain treated by Nd:YAG laser and hydrofluoric acid.

Science.gov (United States)

Hosseini, Mohammad Hashem; Sobouti, Farhad; Etemadi, Ardavan; Chiniforush, Nasim; Shariati, Mahsa

2015-02-01

Adult orthodontic treatment requires bonding orthodontic attachment to dental restorations. Ceramics are commonly used as esthetic restorative materials for the crowns and bridges. The present study evaluated the shear bond strength of metal orthodontic brackets to the feldspathic porcelain surfaces following conditioning by different powers of neodymium-doped yttrium aluminum garnet (Nd:YAG) laser and hydrofluoric acid as a conventional method. Seventy-two glazed porcelain samples were prepared and randomly attributed to six equal groups of 12. In the conventional hydrofluoric (HF) group, the specimens were etched by 9.6% hydrofluoric acid for 4 min. In laser groups, samples were conditioned by 0.75-, 1-, 1.25-, 1.5-, and 2-W Nd:YAG laser for 10 s. Metal brackets were bonded to porcelain samples and after being stored in distilled water for 24 h, they were subjected to thermocycling for 500 cycles. The debonding was carried out by a Zwick testing machine. The data were statistically analyzed by ANOVA and Tamhane multiple comparisons tests. The mean ± SD of the shear bond strength in the laser group 0.75, 1, 1.25, 1.5, and 2 W and HF group was 2.2 ± 0.9, 4.2 ± 1.1, 4.9 ± 2.4, 7 ± 1.7, 9.6 ± 2.7, and 9.4 ± 2.5, respectively. Together with the increased power of laser, the mean shear bond strength was increased continuously and no significant differences were found between the HF group and the laser groups with power of 1.5 or 2 W. Also, there was no significant difference between all test groups in ARI scores. There was no significant difference between bond strength of laser groups with power of 1.5 and 2 W and HF-etched group. So, Nd:YAG laser with appropriate parameters can be used as an alternative method for porcelain etching.

Characterising the disintegration properties of tablets in opaque media using texture analysis.

Science.gov (United States)

Scheuerle, Rebekah L; Gerrard, Stephen E; Kendall, Richard A; Tuleu, Catherine; Slater, Nigel K H; Mahbubani, Krishnaa T

2015-01-01

Tablet disintegration characterisation is used in pharmaceutical research, development, and quality control. Standard methods used to characterise tablet disintegration are often dependent on visual observation in measurement of disintegration times. This presents a challenge for disintegration studies of tablets in opaque, physiologically relevant media that could be useful for tablet formulation optimisation. This study has explored an application of texture analysis disintegration testing, a non-visual, quantitative means of determining tablet disintegration end point, by analysing the disintegration behaviour of two tablet formulations in opaque media. In this study, the disintegration behaviour of one tablet formulation manufactured in-house, and Sybedia Flashtab placebo tablets in water, bovine, and human milk were characterised. A novel method is presented to characterise the disintegration process and to quantify the disintegration end points of the tablets in various media using load data generated by a texture analyser probe. The disintegration times in the different media were found to be statistically different (Pdisintegration times from each other in human versus bovine milk (adjusted P value 0.1685). Copyright © 2015 Elsevier B.V. All rights reserved.

Corrosion behaviour and surface analysis of a Co-Cr and two Ni-Cr dental alloys before and after simulated porcelain firing.

Science.gov (United States)

Qiu, Jing; Yu, Wei-Qiang; Zhang, Fu-Qiang; Smales, Roger J; Zhang, Yi-Lin; Lu, Chun-Hui

2011-02-01

This study evaluated the corrosion behaviour and surface properties of a commercial cobalt-chromium (Co-Cr) alloy and two nickel-chromium (Ni-Cr) alloys [beryllium (Be)-free and Be-containing] before and after a simulated porcelain-firing process. Before porcelain firing, the microstructure, surface composition and hardness, electrochemical corrosion properties, and metal-ion release of as-cast alloy specimens were examined. After firing, similar alloy specimens were examined for the same properties. In both as-cast and fired conditions, the Co-Cr alloy (Wirobond C) showed significantly more resistance to corrosion than the two Ni-Cr alloys. After firing, the corrosion rate of the Be-free Ni-Cr alloy (Stellite N9) increased significantly, which corresponded to a reduction in the levels of Cr, molybdenum (Mo), and Ni in the surface oxides and to a reduction in the thickness of the surface oxide film. The corrosion properties of the Co-Cr alloy and the Be-containing Ni-Cr alloy (ChangPing) were not significantly affected by the firing process. Porcelain firing also changed the microstructure and microhardness values of the alloys, and there were increases in the release of Co and Ni ions, especially for Ni from the Be-free Ni-Cr alloy. Thus, the corrosion rate of the Be-free Ni-Cr alloy increased significantly after porcelain firing, whereas the firing process had little effect on the corrosion susceptibility of the Co-Cr alloy and the Be-containing Ni-Cr alloy. © 2011 Eur J Oral Sci.

XRD and SEM study of alumina silicate porcelain insulator

Science.gov (United States)

Duddi, Dharmender; Singh, G. P.; Kalra, Swati; Shekhawat, M. S.; Tak, S. K.

2018-05-01

Higher strength electrical porcelain is a requirement of industry. This will be achieved by a specific composition of raw materials, which is consisted of clays and feldspars. Water absorption, particle size and insulating properties are of special interest now a day. China clay, Ball clay and Quartz are widely used by ceramic industries in Bikaner district of Rajasthan. Sample for present study were prepared by mixing of above clay, feldspar with MnO2, then shrinkage is observed. Bar shaped samples were prepared and heated up to a temperature of about 1185° C to observe shrinkage. For phase study of XRD and SEM are observed.

A neutron-absorbing porcelain enamel for coating nuclear equipment

International Nuclear Information System (INIS)

Iverson, D.C.

1988-01-01

In 1985, nuclear safety analyses showed that under upset conditions, strict administrative controls were necessary to limit access to a new processing vessel for enriched uranium service at the Savannah River Plant (SRP). In order to increase the level of nuclear safety associated with that vessel, the traditional methods of incorporating neutron absorbers (borated stainless steel, boral, cadmium foil, etc.) were reviewed, however, process conditions did not permit their use. A neutron-absorbing porcelain enamel containing large amounts of cadmium and boron was developed as a safe, cost-effective alternative to traditional neutron-absorbing methods. Several pieces of coated process equipment have been installed or are planned for installation at SRP

Effect of Provisional Cements on Shear Bond Strength of Porcelain Laminate Veneers

OpenAIRE

Altintas, Subutay Han; Tak, Onjen; Secilmis, Asli; Usumez, Aslihan

2011-01-01

Objectives: The purpose of this study was to evaluate the effect of three provisional cements and two cleaning techniques on the final bond strength of porcelain laminate veneers. Methods: The occlusal third of the crowns of forty molar teeth were sectioned and embedded in autopolymerizing acrylic resin. Dentin surfaces were polished and specimens were randomly divided into four groups (n=10). Provisional restorations were fabricated and two provisional restorations were cemented onto each to...

Cyclic testing of porcelain laminiate veneers on superficial enamel and dentin: Pressed vs. conventional layered porcelain

Science.gov (United States)

Tawde, Shweta

Statement of Problem: Clinicians are inclined towards more aggressive teeth preparations to accommodate the thickness of the veneering material. The principle of conservative tooth preparation is compromised. Purpose: By using a conservative approach to treatment with porcelain veneers, long-lasting, esthetic and functional results may be achieved. Sacrificing as little tooth structure as possible and conserving the supporting tissues will facilitate prospective patients. Materials and Methods: Forty extracted human maxillary and mandibular canines were selected. The teeth were divided into one of two groups (pressable and stackable) and further subdivided according to tooth substrate (all-enamel or mixed enamel-dentin exposure). Twenty canine teeth were allotted to the pressable veneer group and 20 were allotted to the stackable veneer group. Of the 20 teeth in the pressable group, all were pressed with a lithium disilicate ceramic system (IPS e.max Press), 10 with labial tooth reduction of 0.3-0.5 mm maintaining superficial enamel (PEN) and the remaining 10 teeth with labial veneer reduction of 0.8-1.0 mm exposing superficial dentin (PDN). Of the 20 teeth in the stackable group, all were stacked/ layered with conventional feldspathic porcelain (Fortune; Williams/ Ivoclar); with labial veneer reduction of 0.3-0.5 mm maintaining superficial enamel (SEN) and the remaining 10 teeth with labial veneer reduction of 0.8-1.0 mm exposing superficial dentin (SDN). Silicon putty matrix was fabricated prior to teeth preparation to estimate the teeth reduction. The prepared facial reduction was limited to the incisal edge. No incisal or palatal/lingual reduction was performed. Impressions of the prepared teeth were taken in medium/light-bodied PVS. Master casts were made in Resin Rock. The stackable group specimens were made with fabricating refractory dies and after following the recommended steps of laboratory procedure, stackable veneers were processed. The pressable group

Adjusting shape-memory properties of amorphous polyether urethanes and radio-opaque composites thereof by variation of physical parameters during programming

International Nuclear Information System (INIS)

Cui, J; Kratz, K; Lendlein, A

2010-01-01

Various composites have been prepared to improve the mechanical properties of shape-memory polymers (SMPs) or to incorporate new functionalities (e.g. magneto-sensitivity) in polymer matrices. In this paper, we systematically investigated the influence of the programming temperature T prog and the applied strain ε m as parameters of the shape-memory creation procedure (SMCP) on the shape-memory properties of an amorphous polyether urethane and radio-opaque composites thereof. Recovery under stress-free conditions was quantified by the shape recovery rate R r and the switching temperature T sw , while the maximum recovery stress σ max was determined at the characteristic temperature T σ,max under constant strain conditions. Excellent shape-memory properties were achieved in all experiments with R r values in between 80 and 98%. σ max could be tailored from 0.4 to 3.7 MPa. T sw and T σ,max could be systematically adjusted from 33 to 71 °C by variation of T prog for each investigated sample. The investigated radio-opaque shape-memory composites will form the material basis for mechanically active scaffolds, which could serve as an intelligent substitute for the extracellular matrix to study the influence of mechanical stimulation of tissue development

White-opaque Switching in Different Mating Type-like Locus Gene Types of Clinical Candida albicans Isolates

Science.gov (United States)

Li, Hou-Min; Shimizu-Imanishi, Yumi; Tanaka, Reiko; Li, Ruo-Yu; Yaguchi, Takashi

2016-01-01

Background: Candida albicans (C. albicans) can become a pathogen causing superficial as well as life-threatening systemic infections, especially in immunocompromised patients. Many phenotypic attributes contribute to its capacity to colonize human organs. In our study, 93 C. albicans isolates from patients of various candidiasis in a hospital of China were surveyed. We aimed to investigate the white-opaque (WO) switching competence, drug sensitivity, and virulence of mating type-like (MTL) a/α isolates. Methods: Internal transcribed spacer (ITS) gene and the MTL configuration were detected in all the isolates by reverse transcription-polymerase chain reaction. White/opaque phenotype and doubling time of cell growth were determined. The minimum inhibitory concentrations of antifungal agent were measured using broth microdilution method. Results: Sixty-four isolates (69.6%) were classified to serotype A, 19 (20.6%) to serotype B, and 9 (9.8%) to serotype C. Moreover, phylogenetic analysis showed that these isolates were divided into four different subgroups of ITS genotypes. Most of our clinical isolates were MTLa/α type, while 6.8% remained MTLa or MTLα type. The frequency of opaque phenotype was 71.0% (66 isolates). Following the guidelines of Clinical and Laboratory Standards Institute M27-A3, all isolates were susceptible to caspofungin and a few (0.6–3.2%) of them showed resistance against amphotericin B, flucytosine, fluconazole, itraconazole, and voriconazole. Conclusions: From these analyses, there were comparatively more C. albicans strains classified into serotype B, and the frequency of opaque phase strains was significant in the clinical isolates from China. Genetic, phenotypic, or drug susceptibility patterns were not significantly different from previous studies. MTLa/α isolates could also undergo WO switching which facilitates their survival. PMID:27824006

Image-based overlay and alignment metrology through optically opaque media with sub-surface probe microscopy

Science.gov (United States)

van Es, Maarten H.; Mohtashami, Abbas; Piras, Daniele; Sadeghian, Hamed

2018-03-01

Nondestructive subsurface nanoimaging through optically opaque media is considered to be extremely challenging and is essential for several semiconductor metrology applications including overlay and alignment and buried void and defect characterization. The current key challenge in overlay and alignment is the measurement of targets that are covered by optically opaque layers. Moreover, with the device dimensions moving to the smaller nodes and the issue of the so-called loading effect causing offsets between between targets and product features, it is increasingly desirable to perform alignment and overlay on product features or so-called on-cell overlay, which requires higher lateral resolution than optical methods can provide. Our recently developed technique known as SubSurface Ultrasonic Resonance Force Microscopy (SSURFM) has shown the capability for high-resolution imaging of structures below a surface based on (visco-)elasticity of the constituent materials and as such is a promising technique to perform overlay and alignment with high resolution in upcoming production nodes. In this paper, we describe the developed SSURFM technique and the experimental results on imaging buried features through various layers and the ability to detect objects with resolution below 10 nm. In summary, the experimental results show that the SSURFM is a potential solution for on-cell overlay and alignment as well as detecting buried defects or voids and generally metrology through optically opaque layers.

Evaluation of bonding strength of porcelain to some commercial nickel-base dental alloys and comparing their interface

Directory of Open Access Journals (Sweden)

Rahim Asghari Salavat

2017-12-01

Conclusion: To replace the replacing of deleterious elements from the chemical composition of dental alloys. The added new elements should control through the oxide layer and the formation of Cr2O3 in porcelain-alloy interfaces for adequate bond strength.

Use of rice straw ash as substitute of feldspar in triaxial porcelain

OpenAIRE

Guzmán, Álvaro; Delvasto, Silvio; Sánchez, Enrique; Amigó Borrás, Vicente

2013-01-01

[EN] The substitution of raw materials for processing high energy consumption materials by agricultural and agro-industrial wastes causes a positive impacts on the environment preservation. One of these residues is rice straw, which according to FAO estimation, its annual production is about 600 million tons. In this research was studied the use of rice straw ash (RSA) as substitute of the use of feldspar in the whiteware production. Clay-feldspar-quartz porcelains are referred to...

Ceramic materials for porcelain veneers: part II. Effect of material, shade, and thickness on translucency.

Science.gov (United States)

Barizon, Karine T L; Bergeron, Cathia; Vargas, Marcos A; Qian, Fang; Cobb, Deborah S; Gratton, David G; Geraldeli, Saulo

2014-10-01

Information regarding the differences in translucency among new ceramic systems is lacking. The purpose of this study was to compare the relative translucency of the different types of ceramic systems indicated for porcelain veneers and to evaluate the effect of shade and thickness on translucency. Disk specimens 13 mm in diameter and 0.7-mm thick were fabricated for the following 9 materials (n=5): VITA VM9, IPS Empress Esthetic, VITA PM9, Vitablocks Mark II, Kavo Everest G-Blank, IPS Empress CAD, IPS e.max CAD, IPS e.maxPress, and Lava Zirconia. VITA VM9 served as the positive control and Lava as the negative control. The disks were fabricated with the shade that corresponds to A1. For IPS e.maxPress, additional disks were made with different shades (BL2, BL4, A1, B1, O1, O2, V1, V2, V3), thickness (0.3 mm), and translucencies (high translucency, low translucency). Color coordinates (CIE L∗ a∗ b∗) were measured with a tristimulus colorimeter. The translucency parameter was calculated from the color difference of the material on a black versus a white background. One-way ANOVA, the post hoc Tukey honestly significant difference, and the Ryan-Einot-Gabriel-Welsch multiple range tests were used to analyze the data (α=.05). Statistically significant differences in the translucency parameter were found among porcelains (PPM9, Empress Esthetic>Empress CAD>Mark II, Everest, e.max CAD>e.max Press>Lava. Significant differences also were noted when different shades and thickness were compared (Pceramic systems designed for porcelain veneers present varying degrees of translucency. The thickness and shade of lithium disilicate ceramic affect its translucency. Shade affects translucency parameter less than thickness. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Phase Transition to an Opaque Plasma in a Sonoluminescing Bubble

Science.gov (United States)

Kappus, Brian; Khalid, Shahzad; Chakravarty, Avik; Putterman, Seth

2011-06-01

Time-resolved spectrum measurements of a sonoluminescing Xe bubble reveal a transition from transparency to an opaque Planck blackbody. As the temperature is <10000K and the density is below liquid density, the photon scattering length is 10 000 times too large to explain its opacity. We resolve this issue with a model that reduces the ionization potential. According to this model, sonoluminescence originates in a new phase of matter with high ionization. Analysis of line emission from Xe* also yields evidence of phase segregation for this first-order transition inside a bubble.

Characterising the disintegration properties of tablets in opaque media using texture analysis

OpenAIRE

Scheuerle, Rebekah L.; Gerrard, Stephen E.; Kendall, Richard A.; Tuleu, Catherine; Slater, Nigel K.H.; Mahbubani, Krishnaa T.

2015-01-01

Tablet disintegration characterisation is used in pharmaceutical research, development, and quality control. Standard methods used to characterise tablet disintegration are often dependent on visual observation in measurement of disintegration times. This presents a challenge for disintegration studies of tablets in opaque, physiologically relevant media that could be useful for tablet formulation optimisation. In this study is explored an application of texture analysis disintegration testin...

Elemental analyses on porcelains of Tang and Song Dynasties excavated from Yongjinwan zone at Jinsha site

Science.gov (United States)

Xia, C. D.; Ge, L. J.; Liu, M. T.; Zhu, J. J.; An, Z.; Bai, B.

2018-02-01

The work presented here carried out elemental analyses on 60 porcelain shards of Tang and Song Dynasties, unearthed from Yongjinwan zone at Jinsha site, Sichuan, China, using a combination of PIXE and RBS methods. Six shards from Liulichang kiln site and 6 from Shifangtang kiln site were also analyzed as reference materials. The factor analyses for the elemental compositions in the bodies and glazes of the total 72 porcelain shards have been performed to explore their similarities and differences. Combining the results of factor analyses on elements in bodies and glazes and the classification by traditional archaeological criteria, the provenances for most of shards unearthed from Yongjinwan zone in Jinsha site could be determined. Majority of shards with a Qiong-kiln style were found as products of Liulichang kiln, this is consistent with Yongjinwan's geographical location and social environment, i.e., Yongjinwan was a suburban settlement nearest to Liulichang kiln in ancient times. Although both products of Liulichang kiln and Shifangtang kiln belonged to Qiong-kiln system and they shared a similar appearance such as red body and celadon glaze, there were distinct differences in chemical composition which could be unraveled by PIXE-RBS measurements and factor analysis. There were no apparent differences of chemical compositions for the same kinds of body and glaze between Tang and Song Dynasties, which may suggest that raw materials and production techniques for the same kinds of body and glaze continued between Tang and Song Dynasties. The chemical characteristics for each kind of body and glaze and the correlations between element composition and porcelain appearance were also obtained in this work.

[Influence of coping material selection and porcelain firing on marginal and internal fit of computer-aided design/computer- aided manufacturing of zirconia and titanium ceramic implant-supported crowns].

Science.gov (United States)

Cuiling, Liu; Liyuan, Yang; Xu, Gao; Hong, Shang

2016-06-01

This study aimed to investigate the influence of coping material and porcelain firing on the marginal and internal fit of computer-aided design/computer-aided manufacturing (CAD/CAM) of zirconia ceramic implant- and titanium ceramic implant-supported crowns. Zirconia ceramic implant (group A, n = 8) and titanium metal ceramic implant-supported crowns (group B, n = 8) were produced from copings using the CAD/CAM system. The marginal and internal gaps of the copings and crowns were measured by using a light-body silicone replica technique combined with micro-computed tomography scanning to obtain a three-dimensional image. Marginal gap (MG), horizontal marginal discrepancy (HMD), and axial wall (AW) were measured. Statistical analyses were performed using SPSS 17.0. Prior to porcelain firing, the measurements for MG, HMD, and AW of copings in group A were significantly larger than those in group B (P 0.05). Porcelain firing significantly reduced MG (P 0.05). The marginal fits of CAD/CAM zirconia ceramic implant-supported crowns were superior to those of CAD/CAM titanium ceramic-supported crowns. The fits of both the CAD/CAM zirconia ceramic implant- and titanium ceramic implant-supported crowns were obviously influenced by porcelain firing.

New insights into the role of Mn and Fe in coloring origin of blue decorations of blue-and-white porcelains by XANES spectroscopy

International Nuclear Information System (INIS)

Zhu, Jian; Luo, Wugan; Ming, Chaofang; Wang, Changsui; Chen, Dongliang; Xu, Wei; Wang, Lihua

2013-01-01

Blue and white porcelain is one of the most valuable ancient ceramics varieties in ancient China. It is well known for its beautiful blue decorations. However, the origin of its blue color has not been very clear till now. In this research, two blue and white porcelains from Jingdezhen, Jiangxi province were selected and Mn and Fe K-edge XANES spectra were recorded from blue decorations with or without transparent glaze. Results showed that Mn K-edge XANES features were almost identical between different samples while that of iron changed. The above findings indicated the positive role of iron in the variation of blue decorations. As for manganese, although more system researches were need, its negative role on the variations of the tone of blue decorations was obtained. On the other hand, the paper also revealed the XAFS results will be affect by the glaze layer above the pigment. These findings provided us more information to understand the coloring origin of blue decorations of blue-and-white porcelain by means of XANES spectroscopy.

New insights into the role of Mn and Fe in coloring origin of blue decorations of blue-and-white porcelains by XANES spectroscopy

Science.gov (United States)

Zhu, Jian; Luo, Wugan; Chen, Dongliang; Xu, Wei; Ming, Chaofang; Wang, Changsui; Wang, Lihua

2013-04-01

Blue and white porcelain is one of the most valuable ancient ceramics varieties in ancient China. It is well known for its beautiful blue decorations. However, the origin of its blue color has not been very clear till now. In this research, two blue and white porcelains from Jingdezhen, Jiangxi province were selected and Mn and Fe K-edge XANES spectra were recorded from blue decorations with or without transparent glaze. Results showed that Mn K-edge XANES features were almost identical between different samples while that of iron changed. The above findings indicated the positive role of iron in the variation of blue decorations. As for manganese, although more system researches were need, its negative role on the variations of the tone of blue decorations was obtained. On the other hand, the paper also revealed the XAFS results will be affect by the glaze layer above the pigment. These findings provided us more information to understand the coloring origin of blue decorations of blue-and-white porcelain by means of XANES spectroscopy.

Metal-ceramic bond strength between a feldspathic porcelain and a Co-Cr alloy fabricated with Direct Metal Laser Sintering technique.

Science.gov (United States)

Dimitriadis, Konstantinos; Spyropoulos, Konstantinos; Papadopoulos, Triantafillos

2018-02-01

The aim of the present study was to record the metal-ceramic bond strength of a feldspathic dental porcelain and a Co-Cr alloy, using the Direct Metal Laser Sintering technique (DMLS) for the fabrication of metal substrates. Ten metal substrates were fabricated with powder of a dental Co-Cr alloy using DMLS technique (test group) in dimensions according to ISO 9693. Another ten substrates were fabricated with a casing dental Co-Cr alloy using classic casting technique (control group) for comparison. Another three substrates were fabricated using each technique to record the Modulus of Elasticity ( E ) of the used alloys. All substrates were examined to record external and internal porosity. Feldspathic porcelain was applied on the substrates. Specimens were tested using the three-point bending test. The failure mode was determined using optical and scanning electron microscopy. The statistical analysis was performed using t-test. Substrates prepared using DMLS technique did not show internal porosity as compared to those produced using the casting technique. The E of control and test group was 222 ± 5.13 GPa and 227 ± 3 GPa, respectively. The bond strength was 51.87 ± 7.50 MPa for test group and 54.60 ± 6.20 MPa for control group. No statistically significant differences between the two groups were recorded. The mode of failure was mainly cohesive for all specimens. Specimens produced by the DMLS technique cover the lowest acceptable metal-ceramic bond strength of 25 MPa specified in ISO 9693 and present satisfactory bond strength for clinical use.

Proton moire fringes for diagnosing electromagnetic fields in opaque materials and plasmas

International Nuclear Information System (INIS)

Mackinnon, A.J.; Patel, P.K.; Price, D.W.; Hicks, D.; Romagnani, L.; Borghesi, M.

2003-01-01

High contrast proton moire fringes have been obtained in a laser-produced proton beam. Moire fringes with modulation of 20%-30% were observed in protons with energies in the range of 4-7 MeV. Monte Carlo simulations with simple test fields showed that shifts in the moire fringes can be used to give quantitative information on the strength of transient electromagnetic fields inside plasmas and materials that are opaque to conventional probing methods

Substrate preference by the porcelain crab Pachycheles monilifer (Crustacea, Anomura: the bryozoan Schizoporella errata or the polychaete Phragmatopoma caudata?

Directory of Open Access Journals (Sweden)

Ana Francisca Tamburus

Full Text Available Differences on reproductive performance between two sampling points of the porcelain crab Pachycheles monilifer from Ubatuba (São Paulo, Brazil, one from Itaguá Beach (living on Schizoporella errata and the other from Grande Beach (living on Phragmatopoma caudata has been previously observed. Therefore could be expected a specific behavior in substrate preference to optimize the best biogenic habitat. Considering this premise, our goal was to test the substrate preference of this species when both substrates were simultaneously available. In total, 185 individuals were collected in these same localities and they were submitted to substrate selection experiments. The trials were conducted on containers with quiet seawater at 28 ± 1°C and under dark photoperiod. Specimens were exposed to substrates by 30 min. Trials started with the release of one animal per treatment in the middle of the opposite side to the substrate inside the containers. After the established time, the substrate preference of each porcelain crab was verified. As result, no preference pattern was found and the choices in the experiment were not significantly different from the expected. This lack of preferences may be an indication that porcelain crabs are generalists in habitat use regardless of sex of individuals and potential benefit in fitness. Therefore, the differences on the reproductive aspects of the P. monilifer probably are associated with environment factors not simulated in this study and may indicate the occurrence of plasticity in habitat selection behavior.

Diversity of yeasts involved in the fermentation of tchoukoutou, an opaque sorghum beer from Benin

NARCIS (Netherlands)

Kayode, A.P.P.; Vieira-Dalode, G.; Linnemann, A.R.; Kotchoni, S.O.; Hounhouigan, A.J.D.; Boekel, van M.A.J.S.; Nout, M.J.R.

2011-01-01

Opaque sorghum beers are traditional alcoholic beverages in several African countries. Known as tchoukoutou in Benin, the beer is often obtained from an uncontrolled fermentation. It is consumed in an actively fermenting state and has a sour taste. The present study characterized and identified the

Main Clinical Outcomes of Feldspathic Porcelain and Glass-Ceramic Laminate Veneers: A Systematic Review and Meta-Analysis of Survival and Complication Rates.

Science.gov (United States)

Morimoto, Susana; Albanesi, Rafael Borges; Sesma, Newton; Agra, Carlos Martins; Braga, Mariana Minatel

2016-01-01

The aim of this study was to perform a systematic review and meta-analysis based on clinical trials that evaluated the main outcomes of glass-ceramic and feldspathic porcelain laminate veneers. A systematic search was carried out in Cochrane and PubMed databases. From the selected studies, the survival rates for porcelain and glass-ceramic veneers were extracted, as were complication rates of clinical outcomes: debonding, fracture/chipping, secondary caries, endodontic problems, severe marginal discoloration, and influence of incisal coverage and enamel/dentin preparation. The Cochran Q test and the I(2) statistic were used to evaluate heterogeneity. Out of the 899 articles initially identified, 13 were included for analysis. Metaregression analysis showed that the types of ceramics and follow-up periods had no influence on failure rate. The estimated overall cumulative survival rate was 89% (95% CI: 84% to 94%) in a median follow-up period of 9 years. The estimated survival for glass-ceramic was 94% (95% CI: 87% to 100%), and for feldspathic porcelain veneers, 87% (95% CI: 82% to 93%). The meta-analysis showed rates for the following events: debonding: 2% (95% CI: 1% to 4%); fracture/chipping: 4% (95% CI: 3% to 6%); secondary caries: 1% (95% CI: 0% to 3%); severe marginal discoloration: 2% (95% CI: 1% to 10%); endodontic problems: 2% (95% CI: 1% to 3%); and incisal coverage odds ratio: 1.25 (95% CI: 0.33 to 4.73). It was not possible to perform meta-analysis of the influence of enamel/dentin preparation on failure rates. Glass-ceramic and porcelain laminate veneers have high survival rates. Fracture/ chipping was the most frequent complication, providing evidence that ceramic veneers are a safe treatment option that preserve tooth structure.

Extraordinary light transmission through opaque thin metal film with subwavelength holes blocked by metal disks.

Science.gov (United States)

Li, Wen-Di; Hu, Jonathan; Chou, Stephen Y

2011-10-10

We observed that when subwavelength-sized holes in an optically opaque metal film are completely covered by opaque metal disks larger than the holes, the light transmission through the holes is not reduced, but rather enhanced. Particularly we report (i) the observation of light transmission through the holes blocked by the metal disks up to 70% larger than the unblocked holes; (ii) the observation of tuning the light transmission by varying the coupling strength between the blocking disks and the hole array, or by changing the size of the disks and holes; (iii) the observation and simulation that the metal disk blocker can improve light coupling from free space to a subwavelength hole; and (iv) the simulation that shows the light transmission through subwavelength holes can be enhanced, even though the gap between the disk and the metal film is partially connected with a metal. We believe these finding should have broad and significant impacts and applications to optical systems in many fields.

Comparison of porcelain bond strength of different metal frameworks prepared by using conventional and recently introduced fabrication methods.

Science.gov (United States)

Kaleli, Necati; Saraç, Duygu

2017-07-01

Most studies evaluating dental laser sintering systems have focused on the marginal accuracy of the restorations. However, the bond strength at the metal-ceramic interface is another important factor that affects the survival of restorations, and currently, few studies focus on this aspect. The purpose of this in vitro study was to compare the porcelain bond strength of cobalt-chromium (Co-Cr) metal frameworks prepared by using the conventional lost-wax technique, milling, direct metal laser sintering (DMLS), and laser cusing, a direct process powder-bed system. A total of 96 metal frameworks (n=24 in each group) were prepared by using conventional lost-wax (group C), milling (group M), DMLS (group LS), and direct process powder-bed (group LC) methods according to International Organization for Standardization standard ISO 9693-1. After porcelain application, a 3-point bend test was applied to each specimen by using a universal testing machine. Data were statistically analyzed using 1-way ANOVA and Tukey honest significant difference tests (α=.05). Failure types at the metal-ceramic interfaces were examined using stereomicroscopy. Additionally, 1 specimen from each group was prepared for scanning electron microscopy analysis to evaluate the surface topography of metal frameworks. The mean bond strength was 38.08 ±3.82 MPa for group C, 39.29 ±3.51 MPa for group M, 40.73 ±3.58 MPa for group LS, and 41.24 ±3.75 MPa for group LC. Statistically significant differences were observed among the 4 groups (P=.016). All groups, except for LS, exhibited adhesive and mixed type bond failure. Both of the laser sintering methods were found to be successful in terms of metal-ceramic bond strength. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

A Study of the Documents of the Supervisors of Jingdezhen Imperial Porcelain Factory of Ming and Qing Dynasties%明清时期景德镇御窑厂督陶官的文献考察

Institute of Scientific and Technical Information of China (English)

陈宁; 徐波

2011-01-01

在景德镇设官监造,宋时已有,元代还成立了专门的官办监陶机构＂浮梁磁局＂。但是宋元时期监陶官的主要职责是收取地方瓷器生产税,设置目的是为了增加国家财政收入,这与明清时期御窑厂督陶官有很大不同。明清时期,朝廷在景德镇建立御窑厂,专门烧造宫廷用瓷,并委派官员督陶。督陶官作为御窑厂的直接负责人,在御器生产过程中担当着至关重要的角色,对景德镇瓷业乃至中国瓷业的发展有着重要影响。本文通过收集和整理大量的文献史料,对明清时期景德镇御窑厂督陶官及其督陶情况进行了全面梳理和比较分析,使读者对其有一个全面清晰的认识和更为深入的理解,填补了陶瓷史中这部分研究的缺漏。%The practice of assigning porcelain production supervisors in Jingdezhen started from Song Dynasty and Yuan Dynasty saw the founding of a porcelain production watchdog, namely, Fuliang Porcelain Bureau. However, the major responsibility of supervisors of Song and Yuan Dynasties was mainly to collect porcelain production taxes so as to increase the national revenue, which differed greatly from that of supervisors of Ming and Qing dynasties. During Ming and Qing Dynasties, the courts decreed to establish the Impedal Porcelain Factory in Jingdezhen to produce porcelain exclusively for imperial use and to assign supervisors for porcelain production. As the direct managers of the Imperial Porcelain Factory, these supervisors played a vital role in the production of porcelain for imperial use and in the development of the porcelain industry of Jingdezhen and that of China at large. This paper has collected and summarized a great many of documents and made a thorough and comparative analysis of all the supervisors of Ming and Qing Dynasties and their supervision so as to present readers a full, clear and better understanding of this field and to fill the gap of this field in the study

Anomalous complete opaqueness in a sparse array of gold nanoparticle chains

International Nuclear Information System (INIS)

Bai Benfeng; Li Xiaowei; Vartiainen, Ismo; Lehmuskero, Anni; Turunen, Jari; Kuittinen, Markku; Vahimaa, Pasi; Kang Guoguo

2011-01-01

We report on an anomalous polarization-switching extinction effect in a sparse array of gold nanoparticle chains: under normal incidence of light, the array is almost transparent for one polarization; whereas it is fully opaque (with nearly zero transmittance) for the orthogonal polarization within a narrow band, even though the nanoparticles cover only a tiny fraction (say, 3.5%) of the transparent substrate surface. We reveal that the strong polarization-dependent short-range dipolar coupling and long-range radiative coupling of gold nanoparticles in this highly asymmetric array is responsible for this extraordinary effect.

Porcelain tiles using nepheline as alternative source of alkalis

International Nuclear Information System (INIS)

Cruz, C.M. da; Oliveira, D.C. de; Faustino, L.M.; Maestrelli, S.C.; Roveri, C.D.

2016-01-01

Porcelain tiles present good aesthetical properties, low water absorption and high mechanical and chemical attack resistance. The feldspar, one of its raw materials, is responsible form diminishing porosity and enhance mechanical resistance. It is normally imported, making the production more expensive. In this paper, it was studied the substitution of feldspar by nepheline under the rheological point of view, determining the optimum amount of deffloculant and the maximum concentration of solids of the suspensions. The results showed similar rheological behaviour, with a small reduction on the maximum concentration of solids as the proportion of nepheline increases. The pieces made with nepheline are darker than the ones made of feldspar; however, the magnetic separation results in lighter pieces. The formulations with nepheline as alkalis source presented a high increase of the density after heating. (author)

Incorporation of feasibility study of residue thin kaolin in of porcelain formulations production; Estudo da viabilidade da incorporacao do residuo fino do caulim na concepcao de formulacoes de porcelanatos

Energy Technology Data Exchange (ETDEWEB)

Almeida, V.S. de; Ferreira, E.C.; Oliveira, T.M. de; Freitas, K.D. de Araujo; Soares Filho, J.E.; Sousa, F.J.P. de, E-mail: vanessaalmeida90@gmail.com [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2016-07-01

The porcelain is the more advanced product among traditional ceramics due to the high technology used in its manufacture and its excellent technological and aesthetic properties. Due to the continuing worldwide development, kaolin processing industries have increased their productivity and consequently generating large amounts of waste, contributing to environmental degradation. Studies are being conducted to analyze the incorporation of such wastes in the ceramic mass compositions. The objective of this study was to evaluate 4 formulations of porcelain as the possibility of using waste coming from the last stage of kaolin processing. Processing occurred by wet grinding process, with uniaxial compacting pressure of 45 MPa after heat treatment at 1250 ° C. Technological tests were carried out physical and mechanical product. The results showed that the addition of fine kaolin residue was presented as an efficient alternative for the porcelain industry. (author)

Evaluation of the roughness of the surface of porcelain systems with the atomic force microscope

International Nuclear Information System (INIS)

Chavarria Rodriguez, Bernal

2013-01-01

The surface of a dental ceramic was evaluated and compared with an atomic force microscope after being treated with different systems of polishing. 14 identical ceramic Lava® Zirconia discs were used to test the different polishing systems. 3 polishing systems from different matrix houses were used to polish dental porcelain. The samples were evaluated quantitatively with an atomic force microscope in order to study the real effectiveness of each system, on the roughness average (Ra) and the maximum peak to valley roughness (Ry) of the ceramic surfaces. A considerable reduction of the surface roughness was obtained by applying different polishing systems on the surface of dental ceramics. Very reliable values of Ra and Ry were obtained by making measurements on the structure reproduced by the atomic force microscope. The advanced ceramics of zirconium oxide presented the best physical characteristics and low levels of surface roughness. A smoother surface was achieved with the application of polishing systems, thus demonstrating the reduction of the surface roughness of a dental ceramic [es

Visualization of latent fingerprints beneath opaque electrical tapes by optical coherence tomography

Science.gov (United States)

Liu, Kangkang; Zhang, Ning; Meng, Li; Li, Zhigang; Xu, Xiaojing

2018-03-01

Electrical tape is found as one type of important trace evidence in crime scene. For example, it is very frequently used to insulate wires in explosive devices in many criminal cases. The fingerprints of the suspects were often left on the adhesive side of the tapes, which can provide very useful clues for the investigation and make it possible for individual identification. The most commonly used method to detect and visualize those latent fingerprints is to peel off each layer of the tapes first and then adopt the chemical methods to develop the fingerprints on the tapes. However, the peeling-off and chemical development process would degrade and contaminate the fingerprints and thus adversely affect the accuracy of identification. Optical coherence tomography (OCT) is a novel forensic imaging modality based on lowcoherence interferometry, which has the advantages of non-destruction, micrometer-level high resolution and crosssectional imaging. In this study, a fiber-based spectral-domain OCT (SD-OCT) system with {6μm resolution was employed to obtain the image of fingerprint sandwiched between two opaque electrical tapes without any pre-processing procedure like peeling-off. Three-dimensional (3D) OCT reconstruction was performed and the subsurface image was produced to visualize the latent fingerprints. The results demonstrate that OCT is a promising tool for recovering the latent fingerprints hidden beneath opaque electrical tape non-destructively and rapidly.

78 FR 71643 - Certain Opaque Polymers; Notice of Commission Decision Amending the Complaint and Notice of...

Science.gov (United States)

2013-11-29

... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-883] Certain Opaque Polymers; Notice of Commission Decision Amending the Complaint and Notice of Investigation AGENCY: U.S. International Trade Commission. ACTION: Notice. SUMMARY: Notice is hereby given that the U.S. International Trade Commission has...

[The bonding mechanisms of base metals for metal-ceramic crown microstructure analysis of bonding agent and gold bond between porcelain and base metals].

Science.gov (United States)

Wang, C C; Hsu, C S

1996-06-01

The use of base metal alloys for porcelain fused to a metal crown and bridges has increased recently because of lower price, high hardness, high tensile strength and high elastic modulus. The addition of beryllium to base metal alloys increased fluidity and improved casting fitness. Beryllium also controlled surface oxidation and bonding strength. The bonding agent and gold bonding agent also affected the bonding strength between porcelain and metal alloys. Four commercially available ceramic base alloys were studied (two alloys contained beryllium element, another two did not). The purpose of this investigation was to study the microstructure between porcelain matrix, bonding agent and alloy matrix interfaces. A scanning electron micro-probe analyzer and energy dispersive X-ray spectroscopy (EDXS) were used to study the distribution of elements (Ni, Cr, Mo, Cu, O, Si, Sn, Al) in four base alloys. The following results were obtained: 1. The thickness of the oxidized layer of Rexillium III alloy and Unitbond alloy (contained beryllium) was thinner than Unibond alloy and Wiron 88 alloy (no beryllium). 2. The thickness of the oxidized layer of alloys in air (10 minutes and 30 minutes) was thinner in Unitbond (2.45 microns and 3.80 microns) and thicker in Wiron 88 (4.39 microns and 5.96 microns). 3. The thickness of the oxidized layer occurring for a duration of ten minutes (in vaccum) showed that the Rexillium III alloy was the thinnest (1.93 microns), and Wiron 88 alloy was the thickest (2.30 microns). But in thirty minutes (vacuum), Unitbond alloy was the thinnest (3.37 microns), and Wiron 88 alloy was the thickest (5.51 microns). 4. The intensity of Cr elements was increased obviously near the interface between Unitbond alloy, Wiron 88 alloy (no beryllium) and oxidized layer, but the intensity of Ni and Mo elements was slightly increased. The intensity of Cr element was not increased markedly between Rexillium III alloy, Unitbond alloy (beryllium) and oxidized

X AFS analysis of ancient chinese porcelain of honglvcai

International Nuclear Information System (INIS)

Wang Lihua; Zhu Jian; Wang Changsui; Duan Huiping; Yan Yan; Xie Yaning

2010-01-01

Structure analysis of Honglvcai, an overglaze ploychrome porcelain produced in China from the Song Dynasty to Ming Dynasty, has been a blank in studies on ancient Chinese ceramics. This work was focused on the oxidation state and local environment of colorants in red, yellow and green decorations on Honglvcai by X-ray absorption fine structure (XAFS). The analysis of Fe K-edge XANES and EXAFS spectra of the red-colored samples indicated that Fe 3+ was mainly located at a distorted octahedral site in a hematite phase, while that if the yellow-colored samples showed that iron was present as both trivalent and divalent cations coordinated with oxygen atoms in an amorphous phase. And Cu K-edge XAFS analysis of the green-colored samples revealed that Cu 2+ was the main constituent coordinated with oxygen atoms in an amorphous phase. (authors)

Moessbauer study of the firing technology of the moon-white Jun porcelain in Chinese Yuan Dynasty

International Nuclear Information System (INIS)

Chen Songhua

1994-01-01

The moon-white Jun porcelain glaze contains Fe 2 O 3 , Fe 3 O 4 and structural iron. The firing atmosphere of ancient Jun kilns was modestly reductive. The firing temperature was slightly above 1250 C. The glaze color appears moon-white, and is related to the low concentration of Fe 2+ . The coordination numbers of Fe 2+ and Fe 3+ are both 4. (orig.)

Sol-gel dip coating of yttria-stabilized tetragonal zirconia dental ceramic by aluminosilicate nanocomposite as a novel technique to improve the bonding of veneering porcelain.

Science.gov (United States)

Madani, Azamsadat; Nakhaei, Mohammadreza; Karami, Parisa; Rajabzadeh, Ghadir; Salehi, Sahar; Bagheri, Hossein

2016-01-01

The aim of this in vitro study was to evaluate the effect of silica and aluminosilicate nanocomposite coating of zirconia-based dental ceramic by a sol-gel dip-coating technique on the bond strength of veneering porcelain to the yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) in vitro. Thirty Y-TZP blocks (10 mm ×10 mm ×3 mm) were prepared and were assigned to four experimental groups (n=10/group): C, without any further surface treatment as the control group; S, sandblasted using 110 μm alumina powder; Si, silica sol dip coating + calcination; and Si/Al, aluminosilicate sol dip coating + calcination. After preparing Y-TZP samples, a 3 mm thick layer of the recommended porcelain was fired on the coated Y-TZP surface. Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray analysis were used to characterize the coating and the nature of the bonding between the coating and zirconia. To examine the zirconia-porcelain bond strength, a microtensile bond strength (μTBS) approach was chosen. FT-IR study showed the formation of silica and aluminosilicate materials. XRD pattern showed the formation of new phases consisting of Si, Al, and Zr in coated samples. SEM showed the formation of a uniform coating on Y-TZP samples. Maximum μTBS values were obtained in aluminosilicate samples, which were significantly increased compared to control and sandblasted groups (P=0.013 and Pcoating can be considered as a convenient, less expensive reliable method for improving the bond strength between dental Y-TZP ceramics and veneering porcelain.

Smooth silk fibroin nanofilm deposited by 1064-nm pulsed laser beam from an opaque target

International Nuclear Information System (INIS)

Nozaki, R.; Nakayama, S.; Senna, M.

2013-01-01

In an attempt to prepare smooth nanostructured thin films of silk fibroin (SF) by near-infrared (NIR) pulsed laser deposition, an opaque target was prepared from an emulsified aqueous solution of SF. Upon irradiation of 1064-nm pulsed laser beam at its fluence 5 J/cm 2 , a thin film of SF was deposited on the Si(100) substrate with its root-mean-square surface roughness, 0.37 nm, smoother than those obtained from a compressed target of SF powders by approximately an order of magnitude. The attainment of an extra-smooth film from the opaque target was discussed in terms of multiple Mie scattering of the incident NIR beam, leading to an increase in the plasma density, intensified optical breakdown, ablation of better dispersed SF molecular units, and a film with more intensive intermolecular cross-linking. - Highlights: • Thin film of silk fibroin with its RMS surface roughness, R rms , 0.37 nm was obtained. • The use of a target from an emulsified solution of SF was the key issue. • Mechanism involved was elucidated in terms of enhanced Mie scattering

A new insight into opaque envelopes in a passive solar house: Properties and roles

International Nuclear Information System (INIS)

Long, Linshuang; Ye, Hong; Liu, Minghou

2016-01-01

Highlights: • A new insight into the opaque envelopes of a passive solar house was gained. • Five parts of envelopes, i.e., roof, south/east/west/north walls, were discussed. • Each part of envelopes were analyzed separately rather than treated as a whole. • Ideal properties of materials for each envelope are diverse from one another. • Differences are related to the envelopes’ leading roles as a heater or a cooler. - Abstract: Passive solar houses are effective solutions for minimizing the operating energy of buildings. The building envelopes of passive solar houses exert a significant influence on the degree of indoor thermal comfort. The focus of this study was the construction of high-performance opaque envelopes, i.e., the roof and walls, for a passive solar house, and a new conception of the envelopes from the perspective of the relation between the properties and roles was provided. The discussion was conducted based on a comprehensive range of envelope materials that were distinguished by the thermal conductivity and volumetric heat capacity. For the first time, each part of the envelopes was analyzed separately rather than considered as an entire envelope. By analyzing each envelope individually, the optimum properties of each envelope were found to be distinct from each other. The distinctions are determined by the dominant role of each envelope, which is associated with the location and absorbed solar irradiation. For summer or hot climate applications, when the dominant role is a cooler, the envelope, e.g., the south wall, should consist of materials with high thermal conductivity and large heat capacity; if a heater is the dominant role, the envelope, e.g., the roof, should consist of materials with low thermal conductivity. For winter or cold climate applications, the envelopes with a leading role of a heater or a cooler require materials with high or low thermal conductivity, respectively. Under the guidance of the results, a discussion

76 FR 2708 - Porcelain-on-Steel Cooking Ware From Taiwan; Top-of-the-Stove Stainless Steel Cooking Ware From...

Science.gov (United States)

2011-01-14

.... 701- TA-267 and 731-TA-304 (Third Review)] Porcelain-on-Steel Cooking Ware From Taiwan; Top-of-the-Stove Stainless Steel Cooking Ware From Korea AGENCY: United States International Trade Commission...-steel cooking ware from Taiwan and the antidumping and countervailing duty orders on imports of top-of...

The effect of core material, veneering porcelain, and fabrication technique on the biaxial flexural strength and weibull analysis of selected dental ceramics.

Science.gov (United States)

Lin, Wei-Shao; Ercoli, Carlo; Feng, Changyong; Morton, Dean

2012-07-01

The objective of this study was to compare the effect of veneering porcelain (monolithic or bilayer specimens) and core fabrication technique (heat-pressed or CAD/CAM) on the biaxial flexural strength and Weibull modulus of leucite-reinforced and lithium-disilicate glass ceramics. In addition, the effect of veneering technique (heat-pressed or powder/liquid layering) for zirconia ceramics on the biaxial flexural strength and Weibull modulus was studied. Five ceramic core materials (IPS Empress Esthetic, IPS Empress CAD, IPS e.max Press, IPS e.max CAD, IPS e.max ZirCAD) and three corresponding veneering porcelains (IPS Empress Esthetic Veneer, IPS e.max Ceram, IPS e.max ZirPress) were selected for this study. Each core material group contained three subgroups based on the core material thickness and the presence of corresponding veneering porcelain as follows: 1.5 mm core material only (subgroup 1.5C), 0.8 mm core material only (subgroup 0.8C), and 1.5 mm core/veneer group: 0.8 mm core with 0.7 mm corresponding veneering porcelain with a powder/liquid layering technique (subgroup 0.8C-0.7VL). The ZirCAD group had one additional 1.5 mm core/veneer subgroup with 0.7 mm heat-pressed veneering porcelain (subgroup 0.8C-0.7VP). The biaxial flexural strengths were compared for each subgroup (n = 10) according to ISO standard 6872:2008 with ANOVA and Tukey's post hoc multiple comparison test (p≤ 0.05). The reliability of strength was analyzed with the Weibull distribution. For all core materials, the 1.5 mm core/veneer subgroups (0.8C-0.7VL, 0.8C-0.7VP) had significantly lower mean biaxial flexural strengths (p Empress and e.max groups, regardless of core thickness and fabrication techniques. Comparing fabrication techniques, Empress Esthetic/CAD, e.max Press/CAD had similar biaxial flexural strength (p= 0.28 for Empress pair; p= 0.87 for e.max pair); however, e.max CAD/Press groups had significantly higher flexural strength (p Empress Esthetic/CAD groups. Monolithic core

Long-term Bond Strength between Layering Indirect Composite Material and Zirconia Coated with Silicabased Ceramics.

Science.gov (United States)

Fushiki, Ryosuke; Komine, Futoshi; Honda, Junichi; Kamio, Shingo; Blatz, Markus B; Matsumura, Hideo

2015-06-01

This study evaluated the long-term shear bond strength between an indirect composite material and a zirconia framework coated with silica-based ceramics, taking the effect of different primers into account. A total of 165 airborne-particle abraded zirconia disks were subjected to one of three pretreatments: no pretreatment (ZR-AB), airborne-particle abrasion of zirconia coated with feldspathic porcelain (ZR-PO-AB), and 9.5% hydrofluoric acid etching of zirconia coated with feldspathic porcelain (ZR-PO-HF). An indirect composite material (Estenia C&B) was then bonded to the zirconia disks after they were treated with one of the following primers: Clearfil Photo Bond (CPB), Clearfil Photo Bond with Clearfil Porcelain Bond Activator (CPB + Activator), Estenia Opaque Primer (EOP), Porcelain Liner M Liquid B (PLB), or no priming (CON, control group). Shear bond strength was tested after 100,000 thermocycles, and the data were analyzed using the Steel-Dwass U-test (α = 0.05). For ZR-PO-AB and ZR-PO-HF specimens, bond strength was highest in the CPB+Activator group (25.8 MPa and 22.4 MPa, respectively). Bond strengths were significantly lower for ZR-AB specimens in the CON and PLB groups and for ZR-PO-AB specimens in the CON, CPB, and EOP groups. Combined application of a hydrophobic phosphate monomer (MDP) and silane coupling agent enhanced the long-term bond strength of indirect composite material to a zirconia coated with silica-based ceramics.

Diffractive imaging of 3-bar targets using an opaque sphere

International Nuclear Information System (INIS)

Weaver, H.J.

1995-01-01

In this discussion we present a description of imaging using an opaque obstruction with a circular cross section (such as a sphere) as the optical imaging element. Image formation is discussed in terms of the convolution product of the point spread function of the system and the optical intensity distribution of the object. It is shown how this convolution product can be efficiently accomplished in the frequency domain using digital technqiues. The emphasis of this report is placed on the numerical generation of the transfer function of the optical system. An analytical example of imaging using this technique with a standard 3-bar target as the object is presented. Experimental verification of the analytical results is also given. copyright 1995 American Institute of Physics

瓷中青色之文化溯源%In the cultural traceability of cyan porcelain

Institute of Scientific and Technical Information of China (English)

杨吴伟

2013-01-01

青瓷是最早成熟的瓷器品种，这种色彩的烧制成功与其工艺特点有关，但在中华文明的文化背景下，它的出现有更深的文化根源，本文正是从青色与人类原始本能、中华玉文化渊源以及生命哲学等方面的内在关系，来探究青色瓷器在中国最早出现的繁盛的根源，赋予青瓷艺术以更深厚的文化意味。%celadon is the earliest mature porcelain varieties, this kind of colour and process characteristics of fire success in Chinese civilization, but about the culture background, which appears to have a deeper cultural roots from cyan, this paper is with human primal instinct, Chinese jade culture ori-gin and life philosophy, etc, to explore the internal relations in China remains the earliest porcelain, given the root of prosperity in a more profound artistic celadon cultural meaning.

First reported case of reactive airway dysfunction syndrome in a laborer due to porcelain tile dust.

Science.gov (United States)

Arif, Tasleem; Malik, Javid Ahmad; Shoib, Sheikh

2013-06-01

Reactive airway dysfunction syndrome (RADS) is a type of non-immunologically mediated asthma-like disease. It usually occurs after a massive exposure to an irritating substance in the atmosphere in the form of smoke, fumes, gases, and vapor. Unlike bronchial asthma, there is no latency to the symptoms seen in RADS. A number of agents are known to cause RADS, but tile dust, as an etiological agent, has not been previously reported. We report a 45-year-old male laborer, who presented with an acute onset of cough, chest tightness, breathlessness, and audible wheeze after his first time exposure to porcelain tile dust within 5 hours of exposure. Lab tests, including, chest X-ray, electrocardiogram, air blood gas analysis, and serum IgE, were unremarkable. Spirometry showed a mild obstruction [forced expiratory volume in 1 second (FEV1)=72% of predicted], while the bronchodilator reversibility test was significant(14% increase in FEV1 above the baseline).Bronchial biopsy revealed a chronic inflammatory reaction with lymphocytic and plasma cell infiltration and more importantly a striking absence of eosinophils. To the best of our knowledge, this is the first reported case of RADS as a result of exposure to tile dust (porcelain ceramics).

Avaliação da superfície da porcelana após a descolagem de braquetes ortodônticos Porcelain surface evaluation after debonding of orthodontic brackets

Directory of Open Access Journals (Sweden)

André Moreira Mattos

2006-10-01

Full Text Available OBJETIVO: o objetivo deste trabalho foi avaliar a influência do tempo de condicionamento ácido em superfície de porcelana e o estado desta após a descolagem de braquetes ortodônticos. METODOLOGIA: foram utilizadas 20 amostras de porcelana feldspática para esmalte (Duceram-LFC divididas em 2 grupos de acordo com o tempo de condicionamento com ácido fluorídico 10% (15 segundos e 1 minuto. Após o ataque ácido, foi aplicado silano (3M Scotchbond, adesivo resinoso (Optibond Solo Plus e resina (Fill Magic nestas superfícies. A descolagem foi realizada através de força de cisalhamento numa máquina universal de ensaios (DL 500 - EMIC calibrada com velocidade fixa de 0,5mm/minuto. O índice do adesivo remanescente (ARI nas superfícies cerâmicas e o estado destas após a remoção dos braquetes foram avaliados através de fotos digitais. RESULTADOS: no grupo 15 segundos, a força de adesão média foi de 3,63MPa, significantemente inferior à do grupo 1 minuto, que foi de 7,18MPa (pAIM: the aim of this study was to evaluate the influence of acid conditioning time in porcelain surface and its characteristics after debonding of orthodontic brackets. METHODS: twenty samples of feldspathic porcelain for enamel (Duceram-LFC were divided in 2 groups according with the amount of time of acid conditioning with hydrofluoric acid 10% (15 seconds and 1 minute. After acid etching, it was applied silane (3M Scotchbond, adhesive (Optibond Solo Plus and resin (Fill Magic in these surfaces. The debonding was done with shear strength through a universal testing machine (DL 500 - EMIC calibrated with a fixed speed of 0.5mm/minute. The adhesive remnant index (ARI in the porcelain surfaces and their characteristics after removal of the brackets were evaluated through digital pictures. RESULTS: in the 15 seconds group, the mean bond strength was 3.63Mpa, significantly lower than the 1 minute group, that was 7.18Mpa (p<0.0001. All fractures during debonding

Mössbauer study of the firing technology of the moon-white Jun porcelain in Chinese Yuan Dynasty

Science.gov (United States)

Songhua, Chen; Zhengyao, Gao; Zhongtian, Sun; Xiande, Chen

1994-12-01

The moon-white Jun porcelain glaze contains Fe2O3, Fe3O4 and structural iron. The firing atmosphere of ancient Jun kilns was modestly reductive. The firing temperature was slightly above 1250 ‡C. The glaze color appears moon-white, and is related to the low concentration of Fe2+. The coordination numbers of Fe2+ and Fe3+ are both 4.

A kinetic study on the development of porosity in porcelain stoneware tile sintering

Directory of Open Access Journals (Sweden)

Jazayeri, S. H.

2007-02-01

Full Text Available The aim of this work is to develop a mathematical model to study the mechanism of elimination of total porosity as a function of soaking time using the Navier-Stokes. Then, parameters of the model such as kinetic constants and apparent activation energy are calculated on the basis of experimental data for a standard porcelain stoneware tile composition. The theoretical data calculated from the model are in good agreement with the experimental data. Using the model developed, it is possible to estimate the best soaking time to obtain minimum total porosity at a given firing temperature . The effects of nepheline on sintering process of porcelain stoneware tile is investigated. It was found that when the nepheline syenite content of the starting mix was increased to 10%, the constant kp of the kinetic equation also increased. The results showed that addition of nepheline to composition of porcelain stoneware bodies was influenced remarkably suitable soaking time to obtain the minimum total porosity and increased shrinkage and bulk density while total and closed porosity fall down.

El propósito de este trabajo es desarrollar un modelo matemático tipo Navier-Stokes para estudiar el mecanismo de eliminación de la porosidad en función del tiempo de maduración en cocción. Los parámetros del modelo tales como las constantes cinéticas y la energía de activación aparente se calcularon a partir de datos experimentales para una composición de gres porcelánico estándar. Los datos teóricos obtenidos a partir del modelo están en buena concordancia con los datos experimentales. Se investigaron los efectos de la nefelina en el gres porcelánico, encontrado que cuando se aumenta el contenido hasta un 10%, la constante de la ecuación cinética kp aumenta. Empleando el modelo desarrollado, es posible estimar el tiempo de maduración en cocción para obtener la porosidad mínima (se alcanza la eliminación de la porosidad debido a la presi

The study of chemical composition and elemental mappings of colored over-glaze porcelain fired in Qing Dynasty by micro-X-ray fluorescence

International Nuclear Information System (INIS)

Cheng Lin; Li Meitian; Kim Youshi; Fan Changsheng; Wang Shanghai; Pan Qiuli; Liu Zhiguo; Li Rongwu

2011-01-01

It is very difficult to measure the chemical composition of colored pigments of over-glaze porcelain by X-ray fluorescence because it contains high concentration of Pb. One of the disadvantages of our polycapillary optics is that it has low transmission efficiency to the high energy X-ray. However, it is beneficial to measure the chemical compositions of rich Pb sample. In this paper, we reported the performances of a tabletop setup of micro-X-ray fluorescence system base on slightly focusing polycapillary and its applications for analysis of rich Pb sample. A piece of Chinese ancient over-glaze porcelain was analyzed by micro-X-ray fluorescence. The experimental results showed that the Cu, Fe and Mn are the major color elements. The possibilities of the process of decorative technology were discussed in this paper, also.

The study of chemical composition and elemental mappings of colored over-glaze porcelain fired in Qing Dynasty by micro-X-ray fluorescence

Energy Technology Data Exchange (ETDEWEB)

Cheng Lin, E-mail: chenglin@bnu.edu.c [Beijing Normal University, Beijing 100875 (China); Key Laboratory of Beam Technology and Material Modification of Ministry of Education, Beijing Radiation Center, Beijing 100875 (China); Li Meitian; Kim Youshi [Beijing Normal University, Beijing 100875 (China); Fan Changsheng; Wang Shanghai [Jiangxi Provincial Institute of Archaeology, Jiangxi Province 330025 (China); Pan Qiuli; Liu Zhiguo [Beijing Normal University, Beijing 100875 (China); Key Laboratory of Beam Technology and Material Modification of Ministry of Education, Beijing Radiation Center, Beijing 100875 (China); Li Rongwu [Beijing Normal University, Beijing 100875 (China)

2011-02-01

It is very difficult to measure the chemical composition of colored pigments of over-glaze porcelain by X-ray fluorescence because it contains high concentration of Pb. One of the disadvantages of our polycapillary optics is that it has low transmission efficiency to the high energy X-ray. However, it is beneficial to measure the chemical compositions of rich Pb sample. In this paper, we reported the performances of a tabletop setup of micro-X-ray fluorescence system base on slightly focusing polycapillary and its applications for analysis of rich Pb sample. A piece of Chinese ancient over-glaze porcelain was analyzed by micro-X-ray fluorescence. The experimental results showed that the Cu, Fe and Mn are the major color elements. The possibilities of the process of decorative technology were discussed in this paper, also.

Influence of the barite tenors of the Jaicos, Piaui, Brazil, clays on the ceramic properties of electric insulator porcelains

International Nuclear Information System (INIS)

Correa, W.L.P.; Lima, M.B.; Carvalho, F.M.S.

2009-01-01

The clays of the Municipality of Jaicos, Piaui, has been used as raw materials for the manufacture of insulators for company located in the municipality of Pedreira - Sao Paulo. It can be noticed in the clay blocks and consolidated, 'lenses' of barite. The mineralogical composition of clay and the nature of these 'lenses' were studied by chemical analysis, X-ray diffraction for mineralogical characterization. The clays are composed primarily by kaolinite, quartz, and some amount of illite and orthoclase. The presence of orthoclase does believe in a recent deposition of these clays. The 'lenses' were characterized as barite, BaSO 4 . To check the influence of barite in the composition of bodies of porcelain to insulators made up six compositions with different levels of barite, obtained their own clay. It applies, then the tests of ceramic fracture to bending, water absorption, apparent porosity to determine the effect of the introduction of barite in the compositions. (author)

Errors resulting from assuming opaque Lambertian clouds in TOMS ozone retrieval

International Nuclear Information System (INIS)

Liu, X.; Newchurch, M.J.; Loughman, R.; Bhartia, P.K.

2004-01-01

Accurate remote sensing retrieval of atmospheric constituents over cloudy areas is very challenging because of insufficient knowledge of cloud parameters. Cloud treatments are highly idealized in most retrieval algorithms. Using a radiative transfer model treating clouds as scattering media, we investigate the effects of assuming opaque Lambertian clouds and employing a Partial Cloud Model (PCM) on Total Ozone Mapping Spectrometer (TOMS) ozone retrievals, especially for tropical high-reflectivity clouds. Assuming angularly independent cloud reflection is good because the Ozone Retrieval Errors (OREs) are within 1.5% of the total ozone (i.e., within TOMS retrieval precision) when Cloud Optical Depth (COD)≥20. Because of Intra-Cloud Ozone Absorption ENhancement (ICOAEN), assuming opaque clouds can introduce large OREs even for optically thick clouds. For a water cloud of COD 40 spanning 2-12 km with 20.8 Dobson Unit (DU) ozone homogeneously distributed in the cloud, the ORE is 17.8 DU in the nadir view. The ICOAEN effect depends greatly on solar zenith angle, view zenith angle, and intra-cloud ozone amount and distribution. The TOMS PCM is good because negative errors from the cloud fraction being underestimated partly cancel other positive errors. At COD≤5, the TOMS algorithm retrieves approximately the correct total ozone because of compensating errors. With increasing COD up to 20-40, the overall positive ORE increases and is finally dominated by the ICOAEN effect. The ICOAEN effect is typically 5-13 DU on average over the Atlantic and Africa and 1-7 DU over the Pacific for tropical high-altitude (cloud top pressure ≤300 hPa) and high-reflectivity (reflectivity ≥ 80%) clouds. Knowledge of TOMS ozone retrieval errors has important implications for remote sensing of ozone/trace gases from other satellite instruments

Directivity patterns and pulse profiles of ultrasound emitted by laser action on interface between transparent and opaque solids: Analytical theory

International Nuclear Information System (INIS)

Nikitin, Sergey M.; Tournat, Vincent; Chigarev, Nikolay; Castagnede, Bernard; Gusev, Vitalyi; Bulou, Alain; Zerr, Andreas

2014-01-01

The analytical theory for the directivity patterns of ultrasounds emitted from laser-irradiated interface between two isotropic solids is developed. It is valid for arbitrary combinations of transparent and opaque materials. The directivity patterns are derived both in two-dimensional and in three-dimensional geometries, by accounting for the specific features of the sound generation by the photo-induced mechanical stresses distributed in the volume, essential in the laser ultrasonics. In particular, the theory accounts for the contribution to the emitted propagating acoustic fields from the converted by the interface evanescent photo-generated compression-dilatation waves. The precise analytical solutions for the profiles of longitudinal and shear acoustic pulses emitted in different directions are proposed. The developed theory can be applied for dimensional scaling, optimization, and interpretation of the high-pressure laser ultrasonics experiments in diamond anvil cell

Using Opaque Image Blur for Real-Time Depth-of-Field Rendering and Image-Based Motion Blur

DEFF Research Database (Denmark)

Kraus, Martin

2013-01-01

While depth of field is an important cinematographic means, its use in real-time computer graphics is still limited by the computational costs that are necessary to achieve a sufficient image quality. Specifically, color bleeding artifacts between objects at different depths are most effectively...... that the opaque image blur can also be used to add motion blur effects to images in real time....

Conductive subtract development without corrosion for photovoltaic applications on porcelain stoneware according to free electrodes process

International Nuclear Information System (INIS)

Reyes-Tolosa, M. D.; Al Aajmi, M.; Orozco-Messana, J.; Donderis, V.; Pascual, M.; Hernandez-Fenollosa, M. A.

2010-01-01

In the incipient world of functional industrial ceramics with photovoltaic applications, there is a need to reduce production costs while maximizing the systems useful life. The thin contact layers currently being manufactured are based on vacuum systems with high production costs and major problems of accelerated corrosion in photovoltaic applications. The electroless process produces very even and compact layers with very low costs through chelate-based chemicals. These layers have been formulated in this study with a view to obtaining appropriate electric characteristics for an optimum photoelectric performance in the assemblies. The morphological requirements are previously fitted through a glaze that acts as a barrier layer between the deposited coating and the porcelain tile, applied through tape casting. The characterisation of the metal layers obtained is started by SEM, an AFM and the Hall effect in order to determine the morphology and chemical characteristics required for these contact layers. The electric characterisation also allows their capacity for offering an optimum performance in the assemblies to be assessed. Finally, the performance of these layers with respect to corrosion is assessed in order to complete the assessment of their industrial suitability. (Author) 13 refs.

Porcelain Factory Worker With Asbestos-related Mesothelioma

Directory of Open Access Journals (Sweden)

Meng-Ting Tsou

2009-10-01

Full Text Available Malignant mesothelioma is a rare tumor among the general population, but for people exposed to asbestos, the lifetime risk is high. A 58-year old man presented with suffering from chest pain, upper back pain, shortness of breath, and coughing that had continued for several months. A chest X-ray revealed right-side pleural effusion; however, pleural biopsy from drainage treatment confirmed a diagnosis of malignant mesothelioma. According to his occupational and environmental history, the patient had worked continuously in a porcelain factory for 30 years. The specific characteristics of his work, making asbestos wallboards and gaskets, entailed working in high-temperature conditions with a high fine-particle content in the atmosphere. The high working temperature caused asbestos debris and dust to fall down regularly from the wallboards, however, it was not until recently that the patient had started to wear personal protection. Asbestos is a significant source of hazardous exposure in old buildings, and this case serves as a reminder of the importance of asbestos-related exposure history, which facilitated the correct diagnosis of pulmonary malignant mesothelioma. Asbestos-containing materials that are now banned or regulated are still present in older buildings and remain an exposure hazard; they continue to be a serious health concern in many countries.

Evaluation of the effect of polishing on flexural strength of feldspathic porcelain and its comparison with autoglazing and over glazing

Directory of Open Access Journals (Sweden)

Jalali H.

2005-06-01

Full Text Available Statement of Problem: Ceramic restorations are popular because they can provide the most natural replacement for teeth. However, the brittleness of ceramics is a primary disadvantage. There are various methods for strengthening ceramics such as metal framework, ceramic cores, and surface strengthening mechanisms through glazing, work hardening and ion exchange. Purpose: The purpose of this study was to evaluate the effect of polish on flexural strength of feldspathic porcelain and to compare it with overglaze and autoglaze. Materials and Methods: In this experimental study, one brand of feldspathic porcelain (colorlogic, Ceramco was used and forty bars (25×6×3 mm were prepared according to ISO 6872 and ADA No. 69. The specimens were randomly divided into four groups: overglazed, auto glazed, fine polish and coarse polish (clinic polish. Flexural strength of each specimen was determined by three point bending test (Universal Testing Machine, Zwick 1494, Germany. Collected data was analyzed by ANOVA and post-hoc test with P<0.05 as the limit of significance. Results: A significant difference was observed among the studied groups (P<0.0001. According to post-hoc test, flexural strength in overglaze and fine polish group were significantly stronger than clinic polish and autoglaze group (P<0.001. Although the mean value for overglazed group was higher than fine polish group, this was not statistically significant (P=0.9. Also no statistical difference was seen between autoglazed and coarse polish group (P=0.2. Conclusion: Based on the findings of this study, flexural strength achieved by fine polish (used in this study can compete with overglazing the feldespathic porcelains. It also can be concluded that a final finishing procedure that involves fine polishing may be preferred to simple staining followed by self-glazing.

Shear bond strength of porcelain laminate veneers to enamel, dentine and enamel-dentine complex bonded with different adhesive luting systems.

Science.gov (United States)

Öztürk, Elif; Bolay, Şükran; Hickel, Reinhard; Ilie, Nicoleta

2013-02-01

The aim of this study was to evaluate the shear bond strength of porcelain laminate veneers to 3 different surfaces by means of enamel, dentine, and enamel-dentine complex. One hundred thirty-five extracted human maxillary central teeth were used, and the teeth were randomly divided into 9 groups (n=15). The teeth were prepared with 3 different levels for bonding surfaces of enamel (E), dentine (D), and enamel-dentine complex (E-D). Porcelain discs (IPS e.max Press, Ivoclar Vivadent) of 2mm in thickness and 4mm in diameter were luted to the tooth surfaces by using 2 light-curing (RelyX Veneer [RV], 3M ESPE; Variolink Veneer [VV], Ivoclar Vivadent) and a dual-curing (Variolink II [V2], Ivoclar Vivadent) adhesive systems according to the manufacturers' instructions. Shear bond strength test was performed in a universal testing machine at 0.5mm/min until bonding failure. Failure modes were determined under a stereomicroscope, and fracture surfaces were evaluated with a scanning electron microscope. The data were statistically analysed (SPSS 17.0) (p=0.05). Group RV-D exhibited the lowest bond strength value (5.42±6.6MPa). There was statistically no difference among RV-D, V2-D (13.78±8.8MPa) and VV-D (13.84±6.2MPa) groups (p>0.05). Group VV-E exhibited the highest bond strength value (24.76±8.8MPa). The type of tooth structure affected the shear bond strength of the porcelain laminate veneers to the 3 different types of tooth structures (enamel, dentine, and enamel-dentine complex). When dentine exposure is necessary during preparation, enough sound enamel must be protected as much as possible to maintain a good bonding; to obtain maximum bond strength, preparation margins should be on sound enamel. Copyright © 2012 Elsevier Ltd. All rights reserved.

A pilot study comparing opaque, weighted bottles with conventional, clear bottles for infant feeding

OpenAIRE

Ventura, Alison K.; Golen, Rebecca Pollack

2014-01-01

Compared to breast-fed infants, bottle-fed infants consume greater volumes and gain more weight during infancy. It is hypothesized that the visual and weight cues afforded by bottle-feeding may lead mothers to overfeed in response to the amount of liquid in the bottle. The aim of the present pilot study was to test this hypothesis by comparing mothers’ sensitivity and responsiveness to infant cues and infants’ intakes when mothers use opaque, weighted bottles (that remove visual and weight cu...

[Computer aided design and manufacture of the porcelain fused to metal crown].

Science.gov (United States)

Nie, Xin; Cheng, Xiaosheng; Dai, Ning; Yu, Qing; Hao, Guodong; Sun, Quanping

2009-04-01

In order to satisfy the current demand for fast and high-quality prosthodontics, we have carried out a research in the fabrication process of the porcelain fused to metal crown on molar with CAD/CAM technology. Firstly, we get the data of the surface mesh on preparation teeth through a 3D-optical grating measuring system. Then, we reconstruct the 3D-model crown with the computer-aided design software which was developed by ourselves. Finally, with the 3D-model data, we produce a metallic crown on a high-speed CNC carving machine. The result has proved that the metallic crown can match the preparation teeth ideally. The fabrication process is reliable and efficient, and the restoration is precise and steady in quality.

Diversity of yeasts involved in the fermentation of tchoukoutou, an opaque sorghum beer from Benin

OpenAIRE

Kayode, A.P.P.; Vieira-Dalode, G.; Linnemann, A.R.; Kotchoni, S.O.; Hounhouigan, A.J.D.; Boekel, van, M.A.J.S.; Nout, M.J.R.

2011-01-01

Opaque sorghum beers are traditional alcoholic beverages in several African countries. Known as tchoukoutou in Benin, the beer is often obtained from an uncontrolled fermentation. It is consumed in an actively fermenting state and has a sour taste. The present study characterized and identified the yeasts involved in the fermentation process of this type of beer using the phenotypical approach. Of 12 beers from 4 different locations, the mean values of the pH, titratable acidity, dry matter c...

Preparation of drop deposited plutonium sources on porcelain support

International Nuclear Information System (INIS)

Miguel, M.; Delle Site, A.; Deron, S.; Raab, W.; Swietly, H.

1984-01-01

Plutonium alpha spectrometry is of interest in safeguards verification, particular for the characterization of test materials for calorimetric assay of plutonium products and for the assay of spent fuel solutions by isotope dilution alpha spectrometry. Such measurements require 0.1-0.3% precision and accuracy in 238 Pu isotopic assay. The present paper reports experience with an alpha spectrometry procedure intended for routine measurements. Sources of excellent quality are prepared very simply and rapidly by drop deposition on porcelain supports. The method of preparation is described which readily produces sources with resolutions of 16 keV (fwhm). The effect of various measurement parameters, tail correction, 241 Am separation and in-growth, are presented. Results are compared with those of mass spectrometry. The relative bias between the 238 Pu/ 239 Pu isotopic ratio measured by the two techniques is of the order of +- 0.5%, with a standard deviation of 1.0%. The performance of alpha spectrometry is at present limited by the quality of the 241 Am separation. (orig.)

Comparison of Marginal and Internal Adaptation of Heat-Pressed and CAD/CAM Porcelain Laminate Veneers and a 2-Year Follow-Up.

Science.gov (United States)

Yuce, Mert; Ulusoy, Mubin; Turk, Ayse Gozde

2017-12-22

To compare marginal and internal adaptations of porcelain laminate veneers fabricated with heat-pressed and CAD/CAM techniques, and to evaluate the clinical performances 2 years after cementation. Thirty heat-pressed and 31 CAD/CAM porcelain laminate veneers were fabricated for 12 patients. Silicone replicas of each veneer were obtained. Replicas were sectioned into 4 parts to measure adaptations of the veneers. A stereomicroscope was used to measure from 3 locations of replicas for marginal, and 9 locations for internal adaptations at 40x magnification. Clinical evaluations were done at baseline and 6, 12, 18, and 24 months after cementation according to the modified United States Public Health Service (USPHS) criteria. Independent samples t-test compared the adaptation values between heat-pressed and CAD/CAM groups. Paired t-test was used to evaluate marginal and internal adaptations of each group. Differences between the modified USPHS criteria ratings of heat-pressed and CAD/CAM groups were determined by the Mann-Whitney U test. Kaplan-Meier analysis was used to analyze the survival ratings of the veneers (p CAD/CAM veneers were 295 and 314.98 μm, respectively, and there was no statistically significant difference (p = 0.541). Internal adaptation values of groups were not statistically different either (201.82 μm for heat pressed; 195.47 μm for CAD/CAM p = 0.734). When marginal and internal adaptation values were compared within groups, there were significant differences both for heat-pressed (p CAD/CAM (p CAD/CAM or heat-pressed, had no effect on the marginal and internal adaptation of porcelain laminate veneers. The results showed that both fabrication techniques performed well after 2 years of clinical performance. © 2017 by the American College of Prosthodontists.

Determination of uranium content in dental porcelains by means of the fission track method and estimation of radiation dose to oral mucosa by radioactive elements

International Nuclear Information System (INIS)

Sairenji, E.; Moriwaki, K.; Shimizu, M.; Noguchi, K.

1980-01-01

Porcelain teeth, some of which contain uranium compounds for aesthetic purpose, have been widely used in dental clinics. Hazardous effects due to uranium radiation have been suggested in recent publications. In the present study uranium concentrations were determined in four major brands of porcelain teeth marketed in Japan using the fission track method, and the absorbed doses to oral tissued were calculated. Average uranium concentrations of the brands studied were determined to be 3.6 ppm (0.33-10 ppm, Japan), 18 ppm (0.69-81 ppm, Japan), 9.4 ppm (2.5-14 ppm, Japan) and 82 ppm (11-205 ppm, U.S.), respectively. The corresponding dose equivalents at the surface of oral mucosal membrane were 2.9 rem yr -1 . 14 rem yr -1 , 7.6 rem yr -1 and 66 rem yr -1 . (author)

The need for radio-opaque side markers on CT of the paranasal sinuses

International Nuclear Information System (INIS)

Nandi, R.; Luk, T.L.; Henson, J.

2003-01-01

AIM: To audit the presence of a radio-opaque 'side marker' routinely placed on the right side of the face of all patients undergoing computed tomography (CT) of the paranasal sinuses in our hospital and to audit awareness levels amongst ear, nose and throat (ENT) clinical and theatre staff regarding the 'marker'. MATERIALS AND METHODS: An audit of 100 CT studies of the paranasal sinuses was carried out with regard to the presence or absence of the marker. A further audit was conducted relating to the awareness amongst ENT clinical staff and theatre nurses regarding the marker. Re-audit of a second cohort of 100 sinus CT studies was carried out after implementing changes indicated by the first audit cycle. Awareness amongst staff concerned was similarly re-audited. RESULTS: In audit cycle I the side marker was positively identified in 85% of the CT examinations and were deemed absent in 15%. Of the clinical staff interviewed, only 30% were aware of the presence of the 'marker' and it's significance. In audit cycle II the 'side marker' was positively identified in 100% of the scans reviewed. Awareness of the presence of the 'marker' amongst clinical staff was found to be 90%. CONCLUSIONS: The routine placement of a radio-opaque side marker on the right zygoma of all patients undergoing CT of paranasal sinuses is a simple yet effective additional means of denoting the correct side whilst interpreting such images. This has important implications regarding surgery. The audit has shown an improvement in both the placement of the side marker as well as in awareness levels amongst staff involved to ensure best practice

Survey on energetic processes of drying and firing of porcelain; Levantamento energetico em processos de secagem e queima de porcelanas

Energy Technology Data Exchange (ETDEWEB)

Ferraz, Andre D.; Machado Junior, Antonio R.; Rocha, Ivan C.C. da; Azevedo, Jorge G.W. de; Konishi, Ricardo; Lehmkuhl, Willian A. [Companhia de Gas de Santa Catarina (SCGAS), Florianopolis, SC (Brazil); Nunes, Andrea T.; Possamai, Talita S.; Nicolau, Vicente de P. [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil)

2012-07-01

This study evaluates the processes of drying and firing of porcelain products. Ambient air heated to an average temperature of 100 deg C is used for drying the pieces. The air heating is done by heat exchangers located within the saturated steam dryers. A main steam's line coming from a boiler fuel feeds all the equipment, while the condensate returned to a reservoir for reheating. The yield obtained from the boiler is about 80%, a reasonable value for this type of equipment. The consumption of this equipment represents 27.6% of the energy used in the stage of burning. However, according to measurements taken about 30% of the energy available in the network is lost in the steam vapor transport and condensation. Considering the potential generation of heat from the fuel, including the boiler efficiency, estimated at about 40% lost energy in the generation and distribution of steam. In accordance with the evaluation, a competitive option would be the direct combustion of natural gas in each dryer, adopting a better control and combustion system, since the products of combustion may impact the quality of the porcelain. A new configuration is proposed as a conclusion. (author)

Estimating nocturnal opaque ice cloud optical depth from MODIS multispectral infrared radiances using a neural network method

Science.gov (United States)

Minnis, Patrick; Hong, Gang; Sun-Mack, Szedung; Smith, William L.; Chen, Yan; Miller, Steven D.

2016-05-01

Retrieval of ice cloud properties using IR measurements has a distinct advantage over the visible and near-IR techniques by providing consistent monitoring regardless of solar illumination conditions. Historically, the IR bands at 3.7, 6.7, 11.0, and 12.0 µm have been used to infer ice cloud parameters by various methods, but the reliable retrieval of ice cloud optical depth τ is limited to nonopaque cirrus with τ < 8. The Ice Cloud Optical Depth from Infrared using a Neural network (ICODIN) method is developed in this paper by training Moderate Resolution Imaging Spectroradiometer (MODIS) radiances at 3.7, 6.7, 11.0, and 12.0 µm against CloudSat-estimated τ during the nighttime using 2 months of matched global data from 2007. An independent data set comprising observations from the same 2 months of 2008 was used to validate the ICODIN. One 4-channel and three 3-channel versions of the ICODIN were tested. The training and validation results show that IR channels can be used to estimate ice cloud τ up to 150 with correlations above 78% and 69% for all clouds and only opaque ice clouds, respectively. However, τ for the deepest clouds is still underestimated in many instances. The corresponding RMS differences relative to CloudSat are ~100 and ~72%. If the opaque clouds are properly identified with the IR methods, the RMS differences in the retrieved optical depths are ~62%. The 3.7 µm channel appears to be most sensitive to optical depth changes but is constrained by poor precision at low temperatures. A method for estimating total optical depth is explored for estimation of cloud water path in the future. Factors affecting the uncertainties and potential improvements are discussed. With improved techniques for discriminating between opaque and semitransparent ice clouds, the method can ultimately improve cloud property monitoring over the entire diurnal cycle.

Characterization of the waste from porcelain polish submitted to the hydrocycloning process; Caracterizacao do residuo provindo do polimento do porcelanato submetido ao processo de hidrociclonagem

Energy Technology Data Exchange (ETDEWEB)

Caetano, A.L.A.; Barbosa Neto, M.C.; Fulgencio, E.B.Gr.; Macedo, D.A.; Ferreira, H.S.; Dutra, R.P.S., E-mail: andre_araujo_jp@hotmail.com [Universidade Federal da Paraiba (UFPB), Joao Pessoa, PB (Brazil). Departamento de Engenharia de Materiais

2016-07-01

The residue generated in porcelain tile polishing has caused great social and environmental worry, due to the release of its solid effluents in inadequate places. This study aims to characterize the residue came from porcelain tile polishing, in order to reuse it in own ceramic industry. For this, was used a laboratory hydrocyclone, equipment used for separation of particles by size. The use of this type of process in the treatment of natural materials can represent quite an efficient tool and cost affordable for the purification of these, since allows to there are separation between the fractions. The different samples were characterized by X-ray diffraction, X-ray fluorescence, particle size analysis and thermal analysis. The results indicate that the resulting material from this process showed different characteristics of the material that was not hydrocycloned, especially as the intensity of the mineralogical phases and the particle size distribution. (author)

Determination of uranium content in dental porcelains by means of the fission track method and estimation of radiation dose to oral mucosa by radioactive elements

International Nuclear Information System (INIS)

Sairenji, Eiko; Moriwaki, Kazunari; Shimizu, Masami; Noguchi, Kunikazu; Anzai, Ikuro.

1979-01-01

Porcelain teeth, some of which contained uranium compounds for aesthetic purpose, have been widely used in dental clinics. Recently, the hazardous effects by uranium radiation were suggested. In the present study, the authors carried out the determination of uranium concentrations of four major brands of porcelain teeth marketed in Japan using the fission track method, and the absorbed doses of oral tissues were calculated by the authors' introduced formula for calculation of alpha radiation. Average uranium concentrations of the brands studied were determined 3.6 ppm (0.33 - 10 ppm, Japan), 18 ppm (0.69 - 81 ppm, Japan), 9.4 ppm (2.5 - 14 ppm, Japan) and 82 ppm (11 - 205 ppm, U.S.A.), respectively. The corresponding dose equivalents at the surface of oral mucosal membrane were 2.9 rem y -1 , 14 rem y -1 , 7.6 rem y -1 and 66 rem y -1 . (author)

Study on the provenance of ancient porcelain excavated in Maojiawan ruin by WDXRF analysis

International Nuclear Information System (INIS)

Xie Guoxi

2007-01-01

In order to determine the provenance of two different kinds of ancient celadons which were excavated in Maojiawan ruin located in Beijing of China and named FLQ (imitated celadon) and WLNQ which is celadon outside and blue-white inside, ten components of each sample's body and glaze were measured by the wave length dispersive X-ray fluorescence (WDXRF) analysis. Multivariates statistical analysis was used to analyze and compare the experiment data with those of LQY (ancient celadon) made in Zhejiang and ancient Jingdezhen porcelain (JDZ) made in Jingdezhen. The results show that the two different kinds of ancient celadons have the same provenance as JDZ, that is, they were produced in Jingdezhen. (authors)

Portable pulse X-ray micro and nanosecond range apparatus for studying fast-going processes in opaque media

International Nuclear Information System (INIS)

Goganov, D.A.; Komyak, N.I.; Pelix, E.A.

Pulse X-radiography (X-ray flash duration in the order of 10 -6 -10 -9 sec) is the principal method for studying fast-going processes in opaque media by serial and parallel radiographic imaging. Description is given and main features are outlined of pulse X-ray apparatus IRA-4b, 5b, 6b producing X-radiation flashes from 0.3 μsec to 10-20 nsec in duration

Cellular ceramics made from porcelain tile polishing wastes: influence of sintering time

International Nuclear Information System (INIS)

Guimaraes, A.F.; Zanelatto, C.C.; Uggioni, E.; Bernardin, A.M.

2009-01-01

This paper deals with the physical, microstructural and mechanical characterization of cellular ceramics made from porcelain polishing wastes, which were expanded by the bubble formation technique during the sintering process. The microstructure, linear expansion, bulk density (mercury immersion) and mechanical behavior (compressive strength) were determined to characterize the glass foam obtained. Moreover, the porcellaneous residue was characterized by chemical and phase analyses, particle size (laser diffraction) and thermal behavior. As a result, the higher the soaking time during heat treatment at 1200 deg C the lower the density obtained for the cellular ceramic due to CO 2 expansion, and lower the mechanical strength of the samples. The microstructure shows spherical cells and completely closed pores, resulting in a cheap way to obtain low density material with adequate mechanical strength, avoiding the disposal of wastes from the ceramic industry. (author)

EDXRF analysis of Straits Chinese porcelains for zirconium and niobium using a cadmium-109 source

International Nuclear Information System (INIS)

Yap, C.T.

1986-01-01

An annular Cd-109 source was used to induce fluorescent X-rays from 37 pieces of Straits Chinese porcelain of which four were modern pieces and the rest were produced from the nineteenth century up to the Republic period (1912-1939). Experimental data show that for zirconium and niobium infinite thickness is reached for a thickness of about 1.5 mm. A plot of the intensity of the K/sub α/ 1 line of Zr against that of Nb shows that all Ch'ing and Republic pieces cluster together and are quite distinct from the modern pieces, allowing easy nondestructive identification of modern fakes

Effect of porcelain polishing addition of waste in properties blocks ceramic

International Nuclear Information System (INIS)

Santana, G.L.; Barbosa Neto, M.C.; Campos, L.F.; Macedo, D.A; Dutra, R.P.S.

2016-01-01

This work has as objective the study of the technological properties of ceramic blocks with addition of residue porcelain polishing. The test samples are produced with clay base, where the waste is introduced in concentrations of 10% and 20% by mass, to evaluate its influence on the properties of the ceramic block. All these materials were characterized by determining their chemical composition (XRF) and X-ray diffraction Sintering was performed at temperatures of 850 ° C, 950 ° C and 1100 ° C with a heating rate of 2 ° C / me and 60 minutes of landing. After this, there was obtained the technological properties of the samples such as: Loss on fire, the burning linear shrinkage, water absorption, porosity and density, as well as, mechanical strength properties through the flexural strength test. The results show that the addition of waste influenced both the technological properties, the mechanical properties evaluated in this study. (author)

LASER-INDUCED BIOACTIVITY IN DENTAL PORCELAIN MODIFIED BY BIOACTIVE GLASS

Directory of Open Access Journals (Sweden)

ANASTASIA BEKETOVA

2012-12-01

Full Text Available The aim of this study was to investigate the impact of laser-liquid-solid interaction method in the bioactivity of dental porcelain modified by bioactive glass. Forty sol-gel derived specimens were immersed in Dulbecco's Modified Eagle's Medium, 31 and 9 specimens of which were treated with Er:YAG and Nd:YAG laser respectively. Untreated specimens served as controls. Incubation of specimens followed. Bioactivity was evaluated, using Fourier Transform Infrared spectroscopy (FTIR, Scanning Electron Microscopy (SEM/Energy Dispersive Spectroscopy (EDS and Transmission Electron Microscopy (TEM. FTIR detected peaks associated with hydroxyapatite on 1 Nd:YAG- and 4 Er:YAG-treated specimens. SEM analysis revealed that Er:YAG-treated specimens were covered by granular hydroxyapatite layer, while Nd:YAG treated specimen presented growth of flake-like hydroxyapatite. TEM confirmed the results. The untreated controls presented delayed bioactivity. In conclusion, Nd:YAG and Er:YAG laser treatment of the material, under certain fluencies, accelerates hydroxyapatite formation. Nd:YAG laser treatment of specific parameters causes the precipitation of flake-like hydroxyapatite in nano-scale.

Influence of stationary and non-stationary conditions on drying time and mechanical properties of a porcelain slab

Science.gov (United States)

Hammouda, Imen; Mihoubi, Daoued

2017-12-01

This work deals with a numerical study of the response of a porcelain slab when subjected to convective drying in stationary and non-stationary conditions. The used model describes heat, mass, and momentum transfers is applied to an unsaturated viscoelastic medium described by a Maxwell model. The numerical code allows us to determine the effect of the surrounding air temperature on drying kinetics and on mechanical stress intensities. Von Mises stresses are analysed in order to foresee an eventual damage that may occur during drying. Simulation results for several temperatures in the range of [30 °C, 90 °C] shows that for the temperature from 30 °C to 60 °C, Von Mises stresses are always lower than the yield strength. But above 70 °C, Von Mises stresses are higher than the ultimate strength, and consequently there is a risk of crack at the end of the constant drying rate period. The idea proposed in this work is to integrate a reducing temperature phase when the predicted Von Mises stress intensity exceeds the admissible stress. Simulation results shows that a non-stationary convective drying (90-60 °C) allows us to optimize costs and quality by reducing the drying time and maintaining Von Mises stress values under the admissible stress.

Microstructure, hardness, corrosion resistance and porcelain shear bond strength comparison between cast and hot pressed CoCrMo alloy for metal-ceramic dental restorations.

Science.gov (United States)

Henriques, B; Soares, D; Silva, F S

2012-08-01

The purpose of this study was to compare the microstructure, hardness, corrosion resistance and metal-porcelain bond strength of a CoCrMo dental alloy obtained by two routes, cast and hot pressing. CoCrMo alloy substrates were obtained by casting and hot pressing. Substrates' microstructure was examined by the means of Optical Microscopy (OM) and by Scanning Electron Microscope (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Hardness tests were performed in a microhardness indenter. The electrochemical behavior of substrates was investigated through potentiodynamic tests in a saline solution (8g NaCl/L). Substrates were bonded to dental porcelain and metal-porcelain bond strength was assessed by the means of a shear test performed in a universal test machine (crosshead speed: 0.5 mm/min) until fracture. Fractured surfaces as well as undestroyed interface specimens were examined with Stereomicroscopy and SEM-EDS. Data was analyzed with Shapiro-Wilk test to test the assumption of normality. The t-test (pmicrostructures whereas hot pressed specimens exhibited a typical globular microstructure with a second phase spread through the matrix. The hardness registered for hot pressed substrates was greater than that of cast specimens, 438±24HV/1 and 324±8HV/1, respectively. Hot pressed substrates showed better corrosion properties than cast ones, i.e. higher OCP; higher corrosion potential (E(corr)) and lower current densities (i(corr)). No significant difference was found (p<0.05) in metal-ceramic bond strength between cast (116.5±6.9 MPa) and hot pressed (114.2±11.9 MPa) substrates. The failure type analysis revealed an adhesive failure for all specimens. Hot pressed products arise as an alternative to cast products in dental prosthetics, as they impart enhanced mechanical and electrochemical properties to prostheses without compromising the metal-ceramic bond strength. Copyright © 2012 Elsevier Ltd. All rights reserved.

Radio opaque marking of pelvic structures : an adjunct to primary radiation therapy of carcinoma of the uterine cervix

International Nuclear Information System (INIS)

Nori, Dattatreyudu; Noumoff, Joel; Cassir, Jorge; Hilaris, B.S.; Lewis, J.L.

1980-01-01

A standardized method of clipping pelvic structures at the time of pretreatment laparotomy for cervical carcinoma is presented. The accurate localization of pelvic structures by clip markers greatly enhances the precision of computerized dosimetry in administering intracavitary radiation. The technical details of the marking procedures, its usefulness and some examples reviewing the advantage of clipping are elaborated. Radio-opaque marking with special reference to computerized dosimetry is also given. (author)

Silk, porcelain and lacquer : China and Japan and their trade with Western Europe and the New World, 1500-1644. A survey of documentary and material evidence

NARCIS (Netherlands)

Llorens Planella, Maria Teresa (Teresa Canepa)

2015-01-01

This dissertation focused on the prolific early European trade and consumption of three Asian manufactured goods: Chinese silk and porcelain, and Japanese lacquer in the sixteenth and early seventeenth centuries, and has shown how the material cultures of late Ming China and Momoyama/early Edo Japan

Impact of brewing process operations on phytate, phenolic compounds and in vitro solubility of iron and zinc in opaque sorghum beer

NARCIS (Netherlands)

Kayodé, A.P.P.; Hounhouigan, J.D.; Nout, M.J.R.

2007-01-01

Opaque sorghum beer is a significant component of the diet of millions of poor people in rural Africa. This study reports the effect of traditional brewing operations on its level of micronutrients, especially iron and zinc. The example of a West African sorghum beer, tchoukoutou, in Northern Benin

Evaluation of mineral kaolinite present in portuguese clays for use in porcelain stoneware; Avaliacao do mineral caulinita presente em argilas portuguesas para uso em gres porcelanato

Energy Technology Data Exchange (ETDEWEB)

Luna da Silveira, G.C. [Instituto Federal do Rio Grande do Norte (IFRN), RN (Brazil); Acchar, W.; Gomes, U.U.; Luna da Silveira, R.V. [Universidade Federal do Rio Grnde do Norte (UFRN), RN (Brazil); Labrincha, A.; Miranda, C.M.P., E-mail: glebacoelli@hotmail.com [Universidade de Aveiro (Portugal)

2016-07-01

Kaolinite is a mineral from the kaolin, product resulting from transformation in depth of alumino silicate mineral type, such as feldspars, plagioclase and feldspars contained in the rocks. Clays are raw materials that have as main characteristic the plasticity property, which gives the product, after applying a certain pressure, a defined shape and an increase in the mechanical resistance when they become from green to dry and then to sintered. Given these characteristics, this paper analyzes the presence of the existing mineral kaolinite in two portuguese clays who are used in the preparation of formulations of porcelain stoneware tiles. The analyzes of the two clays were made by fluorescence x-ray diffraction of x-rays, thermal analysis, particle size and scanning electron microscopy, to better use of this mineral in the formulations. In both clays were found aluminum oxide, as well as mineral quartz, kaolinite and illite. (author)

Clay Treatment To Improve Its Color Parameters To Use Them In Porcelain Stoneware Production; Tratamientos en arcillas con vistas a mejorar sus coordenadas cromaticas para el proceso de fabricacion de gres porcelanico

Energy Technology Data Exchange (ETDEWEB)

Llop, M.; Notari, M.D.; Barrachina, E.; Nebot, I.; Nunez, I.; Carda, J.B.

2010-07-01

The porcelain stoneware tiles production needs high whiteness clays in order to be competitive in the ceramic sector. In the present work, Spanish clays used in the porcelain stoneware tiles production have been characterized in physic, chemist and mineralogical terms, in order to reduce its content of chromophore oxides (Fe2O3 and TiO2). These reduction processes are concerned with different physical and chemical treatments, as sieving at 150mm, magnetic separation using a 0.6T permanent magnet, or acid treatment with HCL and later neutralization with NH3. With these treatments, due to siderite elimination, chromophore oxides as Fe2O3 have been decreased from 2,36% to 1,66% in the chemically treated clay. (Author).

Characterization of kaolin and granite waste for formulation of porcelain stoneware tiles; Caracterizacao de caulim e de residuo de granito para formulacao de gres porcelanato

Energy Technology Data Exchange (ETDEWEB)

Luna da Silveira, G.C. [Instituto Federal do Rio Grande do Norte (IFRN), RN (Brazil); Acchar, W.; Gomes, U.U.; Silva, B.K.O.; Luna da Silveira, R.V. [Universidade Federal do Rio Grande do Norte (UFRN), RN (Brazil); Labrincha, J.A.; Costa, M.C.P., E-mail: glebacoelli@hotmail.com [Universidade de Aveiro (Portugal)

2016-07-01

To produce a stoneware tiles is necessary develop a formulation that satisfies their structural characteristics, micro-structural, physical and mechanical properties. Thus, in order to create a formulation for porcelain stoneware tiles that give use to kaolin and granite waste used in the production of ceramic materials were asked the following characterizations: chemical analysis, mineralogical, thermal and particle size. We found that in the kaolin sample it presents a rate of silicon oxide and aluminum oxide similar to those found in the work of other investigators, about 45.23% SiO2 and 37.39% Al{sub 2}O{sub 3}. In the granite waste, the percentage of silicon oxide and aluminum oxide are also similar to those observed in other studies, with about 74.89% SiO2 and 10.54% Al{sub 2}O{sub 3}. Both the percentage of SiO{sub 2} and Al{sub 2}O{sub 3} founded in these two samples satisfy the percentage required in the manufacturing of porcelain stoneware tiles. (author)

Spray-dried Powder Granulometry: Influence on the Porous Microstructure of Polished Porcelain Tile

Directory of Open Access Journals (Sweden)

Boschi, A. O.

2010-10-01

Full Text Available The low porosity of porcelain tile is the result of strict control of the material’s processing conditions (milling of raw materials, compaction and sintering and the characteristics of the raw materials used in its formulation (formation of liquid phases. Sealed pores remaining after the manufacturing process are revealed at the surface after polishing and are the main factor responsible for staining the product. The porous microstructure of the sintered material depends on the characteristics of the porous microstructure of the green compact and on how the densification process evolves during sintering. The present work evaluated how the size distribution of spray-dried granules acts upon the porous microstructure of green compacts and of polished porcelain tile. The results revealed that minor adjustments in the granulometric distribution curve can reduce the visibility of stains on the polished surface, thus improving this property.

La baja porosidad de los revestimientos porcelánicos, es el resultado del estricto control que se ejerce sobre los distintos parámetros que condicionan el procesamiento de los materiales ( molienda de la materias primas, compactación y sinterización y de las características de las materias primas empleadas en su formulación (formación de fases líquidas. Los poros cerrados que se generan durante la fabricación, y que se abren en la superficie durante el proceso de pulido, son los principales responsables de las manchas que aparecen en la superficie del material. La porosidad microestructural de los materiales sinterizados está condicionada por la porosidad microstrucutural de la pieza en verde y por la evolución del proceso de densificación durante la sinterización. E l trabajo presente evalúa la influencia de la distribución granulométrica del granulado procedente del atomizador sobre la porosidad granulométrica de las piezas en verde y de la pieza ya pulida. Los resultados revelan como

Structural properties of the red-color overglazes on the Kakiemon-style porcelains produced in the later 17th century by means of X-ray diffraction (I Propriedades estruturais, por difração de raios X, de esmaltes vermelhos de porcelanas do estilo Kakiemon produzidos no fim do século 17 (I

Directory of Open Access Journals (Sweden)

M. Hidaka

2009-06-01

Full Text Available Kakiemon-style porcelains produced at Arita areas (SAGA in Kyushu Island are famous Japanese porcelains. The porcelain-techniques creating its elegant and bright red-color underglaze and overglaze were found and developed in 1650's (early Edo period first by Kakiemon kiln. Red-color overglaze and transparent glaze of the Kakiemon-style porcelains have been investigated by means of X-ray diffraction using synchrotron radiation. The results suggest that the red-color brightness is mainly induced by micro-structural correlation between α-Fe2O3 fine particles, as red-color emission elements, and other oxides of SiO2, Al2O3, CaO, KNaO, PbO. The stability of the red-overglaze on the porcelain surface is related to interfacial fusion of the glasses existing in the fritted red-overglaze and the transparent glaze on the porcelain body. The ancient porcelain-techniques of the Kakiemon-style porcelains are clearly based on the micro-structural and material properties of the overglazes, the underglazes, and the transparent glazes, though the techniques were experimentally and accidentally found and developed in the Edo period.As porcelanas do estilo Kakiemon produzidas nas áreas de Arita (SAGA na ilha Kyushu são porcelanas japonesas famosas. As técnicas de produzir porcelanas com os elegantes e brilhantes vidrados de cores vermelho brilhante foram encontradas e desenvolvidas nos anos 1650 (início do período Edo primeiramente em fornos Kakiemon. Vidrados vermelhos e vidrados transparentes de porcelanas do estilo Kakiemon foram investigadas por meio de difração de raios X com radiação sincrotron. Os resultados sugerem que o brilho de cor vermelha é principalmente induzido pela correlação microestrutural entre finas partículas de α-Fe2O3, como elementos emissores de cor vermelha, além de outros óxidos como SiO2, Al2O3, CaO, KNaO, e PbO. A estabilidade dos vidrados na superfície da porcelana com vidrado vermelho está relacionada com a fus

Photons coming from an opaque obstacle as a manifestation of heavy neutrino decays

Science.gov (United States)

Reynoso, Matías M.; Romero, Ismael; Sampayo, Oscar A.

2018-05-01

Within the framework of physics beyond the standard model, we study the possibility that mesons produced in the atmosphere by the cosmic-ray flux decay to heavy Majorana neutrinos and the latter, in turn, decay mostly to photons in the low-mass region. We study the photon flux produced by sterile Majorana neutrinos (N ) decaying after passing through a massive and opaque object such as a mountain. To model the production of N 's in the atmosphere and their decay to photons, we consider the interaction between the Majorana neutrinos and the standard matter as modeled by an effective theory. We then calculate the heavy neutrino flux originated by the decay of mesons in the atmosphere. The surviving photon flux, originated by N decays, is calculated using transport equations that include the effects of Majorana neutrino production and decay.

Origin of opaque assemblages in C3V meteorites - Implications for nebular and planetary processes

Science.gov (United States)

Blum, Joel D.; Wasserburg, G. J.; Hutcheon, I. D.; Beckett, J. R.; Stolper, E. M.

1989-01-01

The results of analyses of meteoritic opaque assemblages (OAs) are presented and used in conjunction with literature data on phase equilibria and diffusion to further develop the hypothesis of Blum et al. (1989) for the origin of OAs in Ca,Al-rich inclusions (CAIs). Based on the results of the analyses, it is suggested that OAs formed after the crystallization of host CAIs by exsolution, sulfidation, and oxidation of precursor alloys at low temperatures (about 770 K) and higher than solar gas sulfur and oxygen fugacities. This model contrasts with previous models that call upon the formation of CAI OAs by aggregation of previously formed phases in the solar nebula prior to the crystallization of CAIs.

Process Development of Porcelain Ceramic Material with Binder Jetting Process for Dental Applications

Science.gov (United States)

Miyanaji, Hadi; Zhang, Shanshan; Lassell, Austin; Zandinejad, Amirali; Yang, Li

2016-03-01

Custom ceramic structures possess significant potentials in many applications such as dentistry and aerospace where extreme environments are present. Specifically, highly customized geometries with adequate performance are needed for various dental prostheses applications. This paper demonstrates the development of process and post-process parameters for a dental porcelain ceramic material using binder jetting additive manufacturing (AM). Various process parameters such as binder amount, drying power level, drying time and powder spread speed were studied experimentally for their effect on geometrical and mechanical characteristics of green parts. In addition, the effects of sintering and printing parameters on the qualities of the densified ceramic structures were also investigated experimentally. The results provide insights into the process-property relationships for the binder jetting AM process, and some of the challenges of the process that need to be further characterized for the successful adoption of the binder jetting technology in high quality ceramic fabrications are discussed.

Use of rice straw ash as substitute of feldspar in triaxial porcelain

International Nuclear Information System (INIS)

Alvaro Guzman, A.; Silverio Delvasto, A.; Enrique Sanchez, V.; Vicente Amigo, B.

2013-01-01

The substitution of raw materials for processing high energy consumption materials by agricultural and agro-industrial wastes causes a positive impacts on the environment preservation. One of these residues is rice straw, which according to FAO estimation, its annual production is about 600 million tons. In this research was studied the use of rice straw ash as substitute of the use of feldspar in the white ware production. Clay-feldspar-quartz porcelains are referred to as triaxial white ware. Specimens of semidry triaxial mixtures, where feldspar was substituted for different percentages of CTA, were prepared by uniaxial pressing, followed by drying and sintering. Physical and mechanical properties of sintered bodies were evaluated. The porosity and the compressive strength of the fired pieces do increase with additions of up to 75% of CTA in substitution of feldspar. Their mineralogical phases were determined by DRX and SEM; grains of quartz, and needles of primary and secondary mullite were identified in a vitreous phase. It was concluded that feldspar can be substituted positively by CTA in white ware pastes. (Author) 22 refs.

EPID detection of radio-opaque markers for the evaluation of prostate position during megavoltage irradiation: a clinical study

International Nuclear Information System (INIS)

Vigneault, E.; Pouliot, J.; Laverdiere, J.; Roy, J.

1995-01-01

Purpose: To assess daily prostatic apex motion relative to pelvic bone structures during megavoltage irradiation. Materials and Methods: Radio-opaque markers were implanted under ultrasound guidance near the prostatic apex of ten patients with localized prostatic carcinoma. Patients were subsequently treated with four field box technique at a beam energy of 23 MV. During treatment, on-line images were obtained with an Electronic Portal Imaging Device (EPID) for each field and fraction. The marker was easily identified, even on unprocessed images and the distance between the marker and a bony landmark was measured. Timelapse movie for the complete treatment of each patient were also reviewed. After the completion of treatment, a transrectal ultrasound examination was performed to verify the position of the marker relative to the apex. Results: Over 1000 digital portal images were acquired. Antero-posterior and lateral views of each fraction were analysed. The quality of portal images obtained with megavoltage irradiation was good. Even without image histogram equalization it was possible to evaluate pelvic bone structures. Moreover, the radio-opaque marker was easily visible on every on-line portal image. Qualitatively, the review of timelapse movies showed important interfraction motions of the marker while bone structures remained stable. Quantitatively, the position of the marker were measured for each fraction. Marker displacements of up to 1,4 cm were measured between two consecutive days of treatment. Important marker motions were predominately in the antero-posterior and cephalo-caudal directions. Position of the markers relative to the prostatic apex were verified with ultrasound at the end of the treatments and were found to remain globaly at their original position. Intratreatment images were reviewed in two cases and no change in marker positions was observed. Our results, obtained during the treatment courses, indicate similar or larger prostate motions

Light mirror reflection combined with heating/cooling curves as a method of studying phase transitions in transparent and opaque petroleum products: Apparatus and theory

International Nuclear Information System (INIS)

Shishkin, Yu.L.

2007-01-01

A portable low weight low cost apparatus 'Phasafot' and method for determining pour and cloud points of petroleum products, as well as precipitation and melting temperatures of paraffins in both transparent (diesel fuels), semi-transparent (lube oils) and opaque (crude oils) samples are described. The method consists in illuminating the surface of a sample with an oblique light beam and registering the intensity of specularly reflected light while heating/cooling the sample in the temperature range of its structural transitions. The mirror reflection of a light beam from an ideally smooth liquid surface falls in intensity when the surface becomes rough (dim) due to crystal formation. Simultaneous recording of the temperature ramp curve and the mirror reflection curve enables the determination of the beginning and end of crystallization of paraffins in both transparent and opaque petroleum products. Besides, their rheological properties can be accurately determined by rocking or tilting the instrument while monitoring the sample movement via its mirror reflection

Zeolitic adsorbent synthesized from powdered waste porcelain, and its capacity for heavy metal removal

International Nuclear Information System (INIS)

Wajima, T.; Ikegami, Y.

2006-01-01

A zeolitic adsorbent was synthesized from powdered waste porcelain kept at 80 o C for 24 h. The product contained the zeolite phases Na-P1 and hydroxysodalite. The product with the highest cation exchange capacity (CEC) was synthesized using 4 M NaOH and the sample weight / volume of alkali solution ratio was 1/4. The highest CEC obtained for the product was almost 1900 mmol/kg, which is the same as that of natural zeolite. The product with the highest CEC was tested for its ability to remove heavy metals (Fe, Cu, Ni, Zn, Pb, Cd, Mn, Cr, Al, B,Mo) from an acidic solution (pH 2). The product can neutralize the acidic solution to almost pH 7, and the capacity of the product for the removal of heavy metals is higher than that of the natural zeolite, except for Mo and B. (authors)

Illustration of compositional variations over time of Chinese porcelain glazes combining micro-X-ray fluorescence spectrometry, multivariate data analysis and Seger formulas

OpenAIRE

Van Pevenage, J.; Verhaeven, E.; Vekemans, B.; Lauwers, D.; Herremans, D.; De Clercq, W.; Vincze, L.; Moens, L.; Vandenabeele, P.

2015-01-01

Abstract: In this research, the transparent glaze layers of Chinese porcelain samples were investigated. Depending on the production period, these samples can be divided into two groups: the samples of group A dating from the Kangxi period (1661-1722), and the samples of group B produced under emperor Qianlong (1735-1795). Due to the specific sample preparation method and the small spot size of the X-ray beam, investigation of the transparent glaze layers is enabled. Despite the many existing...

Tribological study of PTFE composites loaded with porcelain tile waste; Estudo tribologico de compositos de PTFE carregados com rejeito de porcelanato

Energy Technology Data Exchange (ETDEWEB)

Oliveira, P.M.; Araujo Neto, A.P.; Souza, J.R.; Medeiros, J.T.N., E-mail: plinio_rpg@hotmail.com [Universidade Federal do Rio Grande do Norte (GET/UFRN), Natal, RN (Brazil). Grupo de Estudos de Tribologia e Integridade Estrutural

2016-07-01

The Brazilian northeast is one of the largest producers of clays that burn in the white form and disposal of tailings from the process of polishing the ceramic pieces of porcelain stands out as a major source of environmental degradation. This problem can be reduced by adding such material as filler in composites, in order to improve the mechanical properties of the polymeric matrix. Polytetrafluoroethylene (PTFE) is characterized as a good solid lubricant, because it has excellent properties such as low coefficient of friction (0.01 < μ < 0.1), thermal stability at high temperatures and chemical resistance. However, the pure PTFE has high wear rates (greater than 10-13m2/N) leading to early failures of various components. To reuse the Tailings of Porcelain (TP), composites of PTFE + TP were developed in three different compositions (85:15, 75:25 and 65:35). For this investigation the particle size distribution and some chemical characteristics of the tailings by testing XRD, XRF, SEM and EDS were performed, registering a large amount of silica, aluminum and other metals. Roughness, wettability and sclerometry also were performed. It was noted that the values of arithmetic average roughness, Ra, is higher for composites with higher percentage of TP, in addition they have a lower contact angle and higher surface energy to distilled water, characterized as hydrophilic. The results of energy of deformation provided by the sclerometry test were non-linear. (author)

Gross photosynthesis explains the ‘artificial bias’ of methane fluxes by static chamber (opaque versus transparent) at the hummocks in a boreal peatland

International Nuclear Information System (INIS)

Luan, Junwei; Wu, Jianghua

2014-01-01

The closed chamber technique has been widely employed to detect methane emissions, despite little being known about whether the absence or presence of light will impact the flux estimation. Here, we employed a laser greenhouse gas analyzer with an opaque—transparent chamber pair to measure the methane emission rate in a boreal peatland complex. Microtopography (i.e., hummocks and hollows) in natural and drained peatlands, and plant communities (i.e., grasses and shrubs) in a pasture converted from natural peatlands, were considered to cover the local heterogeneity. Our results indicated that opaque chambers (0.58–0.78 g CH 4 m −2 during the growing season) measured a significantly higher (∼2–3 times) methane emission at the hummocks than transparent chambers (∼0.24 g CH 4 m −2 ); however, a similar phenomenon was not found at the hollows or at other measurement plots. Gross photosynthesis explained 44%–47% of the temporal variation of the ‘artificial bias’ (the difference in methane flux obtained by the opaque versus transparent chambers) at the hummocks. Additionally, both water table depth and surface soil moisture significantly explained spatial variations of methane emissions. Our study suggests that microtopography has a significant influence on the artificial bias in methane emission estimation and the artificial properties of a chamber (transparency/opacity) method can be vitally important in some cases (i.e., hummocks), and negligible in others (i.e., hollows). The observed connection between the photosynthesis process and the ‘artificial bias’ of closed chambers (opaque versus transparent) can be used to improve methane flux modeling. Separate parameterization schemes are needed for methane transportation under the presence or absence of light. (paper)

List context effects in languages with opaque and transparent orthographies: A challenge for models of reading

Directory of Open Access Journals (Sweden)

Daniela eTraficante

2014-09-01

Full Text Available This paper offers a review of data which show that reading is a flexible and dynamic process and that readers can exert strategic control over it. Two main hypotheses on the control of reading processes have been suggested: the route de-emphasis hypothesis and the time-criterion hypothesis. According to the former, the presence of irregular words in the list might lead to an attenuation of the non-lexical process, while the presence of non-words could trigger a de-emphasis of the lexical route. An alternative account is proposed by the time-criterion hypothesis whereby the reader sets a flexible deadline to initiate the response. According to the latter view, it is the average pronunciation difficulty of the items in the block that modulates the time-criterion for response. However, it is worth noting that the list composition has been shown to exert different effects in transparent compared to opaque orthographies, as the consistency of spelling-sound correspondences can influence the processing costs of the non-lexical pathway. In transparent orthographies, the non-lexical route is not resource demanding and can successfully contribute to the pronunciation of regular words, thus its de-emphasis could not be as useful/necessary as in opaque orthographies. The complex patterns of results from the literature on list context effects are a challenge for computational models of reading which face the problem of simulating strategic control over reading processes. Different proposals suggest a modification of parameter setting in the non-lexical route or the implementation of a new module aimed at focusing attention on the output of the more convenient pathway. Simulation data and an assessment of the models’ fit to the behavioral results are presented and discussed to shed light on the role of the cognitive system when reading aloud.

Evaluation of Microflow Digital Imaging Particle Analysis for Sub-Visible Particles Formulated with an Opaque Vaccine Adjuvant.

Directory of Open Access Journals (Sweden)

Grant E Frahm

Full Text Available Microflow digital imaging (MDI has become a widely accepted method for assessing sub-visible particles in pharmaceutical formulations however, to date; no data have been presented on the utility of this methodology when formulations include opaque vaccine adjuvants. This study evaluates the ability of MDI to assess sub-visible particles under these conditions. A Fluid Imaging Technologies Inc. FlowCAM® instrument was used to assess a number of sub-visible particle types in solution with increasing concentrations of AddaVax™, a nanoscale squalene-based adjuvant. With the objective (10X used and the limitations of the sensor resolution, the instrument was incapable of distinguishing between sub-visible particles and AddaVax™ droplets at particle sizes less than 5 μm. The instrument was capable of imaging all particle types assessed (polystyrene beads, borosilicate glass, cellulose, polyethylene protein aggregate mimics, and lysozyme protein aggregates at sizes greater than 5 μm in concentrations of AddaVax™ up to 50% (vol:vol. Reduced edge gradients and a decrease in measured particle sizes were noted as adjuvant concentrations increased. No significant changes in particle counts were observed for polystyrene particle standards and lysozyme protein aggregates, however significant reductions in particle counts were observed for borosilicate (80% of original and cellulose (92% of original particles. This reduction in particle counts may be due to the opaque adjuvant masking translucent particles present in borosilicate and cellulose samples. Although the results suggest that the utility of MDI for assessing sub-visible particles in high concentrations of adjuvant may be highly dependent on particle morphology, we believe that further investigation of this methodology to assess sub-visible particles in challenging formulations is warranted.

Correlation between the mechanical property and microstructure of porcelain with high alumina contents

International Nuclear Information System (INIS)

Goulart, E.P.; Jordao, M.A.P.; Souza, D.D.D. de; Kiyohara, P.K.

1989-01-01

The substitution of quartz by a alumina in porcelain bodies produces high increase in mechanical strenght of the fired body. In the present paper, body microstruture variations caused by gradual quartz by alumina substitution have been studied and correlated to physical characteristics variations. Several bodies with quartz content varying from 22% to 0% and accordingly, the alumina content varying from 0% to 22% have been prepared. Other quartz-free bodies and the alumina content going up to 40% have been prepared. Three different alumina types have been used: two of them were of microcrystal type, the original crystal size between 1-5μm and obtained by calcining aluminum hydroxide from Bayer process; the third one is an originally macrocrystal type alumina obtained by grinding electrofused material. The sintering temperature ranged from 1250 0 C to 1400 0 C with 50 0 C of intervals between each firing. Tests on specimens covered flexural strenght, water absortion, apparent density and porosity. Microstruture variations and new mineral formation was continuously detected by scanning electron microscopy and X-ray diffraction [pt

Oxide layer characteristics and interfacial analysis of porcelain fused to high-gold alloy using multitechnique analysis methods

Directory of Open Access Journals (Sweden)

Hao-Sheng Chang

2017-12-01

Full Text Available Background/purpose: In a previous fractural study, high-gold crowns possessed the second highest fracture force. The objective of this study is to analyze the interface of porcelain fused to high-gold alloy using different observation devices. Materials and methods: High-gold crowns specimens with the morphology of a maxillary second premolar were compressed vertically in the center of the occlusal surface until fracture using a universal testing machine. The fractured surfaces were examined using scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM/EDX to determine the failure mode. The ceramic–metal interface of the crown was examined with electron probe microanalysis (EPMA. In addition, sheet specimens with dimensions of 10×9×4 mm3 were prepared to examine the surface morphology and composition of high-gold alloy after oxidation using X-ray photoelectron spectrometer (XPS. Results: The average fracture force was 1368±312 N. Photograph of fractured crown and SEM/EDX analyses reveal that the crown initially suffered from cohesive failure in the upper and middle regions, with the fracture occurring mostly within the ceramic. XPS results and both EPMA color photomicrographs of crown and sheet specimens show that indium was observed along the porcelain–metal interface with a 1- to 2-μm disrupted zone of oxide layer. Conclusion: In2O3 and Au were found along the interface from the multitechnique analysis methods; the presence of this oxide at the boundary promotes ceramic–metal adhesion. In2O3 is suggested to be beneficial for the second highest fracture resistance in a previous fractural study of implant-supported crowns. Keywords: electron probe microanalysis, gold–platinum alloy, scanning electron microscopy combined with energy-dispersive X-ray analysis, X-ray photoelectron spectroscopy

Recycling of the Granite Quarries and Municipal Incinerator Wastes for the Processing of New Materials as Porcelainized Stoneware

Directory of Open Access Journals (Sweden)

Hernández-Crespo, M. S.

2000-12-01

Full Text Available In the 1980s started in the ceramic sector the material conception of porcelainized stoneware, a product with versatile and modern characteristics similar to those of the natural stone, depicting improved properties to the marble and granite. Porcelanized stoneware is a compact ceramic material, very hard and homogeneous, generally not fully vitreous (unglazed in its surface, obtained by fast firing from compositions enriched in kaolinite, which contain a large quantity of fluxes. The raw materials for body are a mixture that contains an adequate relationship of kaolinitic clays, feldspars and quartz. Such material is characterized by its low or almost zero porosity, being adequated to sustain heavy and high traffic intensity for uses in and outside of buildings with wide range of aspects, desings and colors. By considering the chemistry and mineralogical composition of the granite and incinerator wastes, this paper describes their use in the processing of construction materials, specifically, in a new type of stoneware flooring and covering materials. According to the most of the physical and mechanical properties here determined, these "Modified Porcelainized Stoneware" (MPS materials are close to the conventional porcelainized stoneware and glass ceramics products.

Hacia la década de los años 80 se inicia en el sector cerámico la concepción del gres porcelánico, material de características modernas y versátiles semejantes a las de la piedra natural, pero que incluso supera en utilidad y prestaciones al mármol y al granito. El gres porcelánico es un material cerámico compacto, muy duro y homogéneo, no vidriado en su superficie, obtenido por cocción rápida de composiciones ricas en caolinita y una gran cantidad de fundentes; es decir, de una mezcla cerámica que contiene una relación adecuada de arcillas de tipo caolinítico, feldespatos y cuarzo. Dicho material se caracteriza por su baja o casi nula porosidad; es ideal

Preparation and characterization of new dental porcelains, using K-feldspar and quartz raw materials. Effect of B2O3 additions on sintering and mechanical properties.

Science.gov (United States)

Harabi, Abdelhamid; Guerfa, Fatiha; Harabi, Esma; Benhassine, Mohamed-Tayeb; Foughali, Lazhar; Zaiou, Soumia

2016-08-01

The aim of this work was to determine the effect of temperature and boric oxide (B2O3) addition on sintering and mechanical properties of a newly developed dental porcelain (DP) prepared from local Algerian raw materials. Based on a preliminary work, the new selected composition was 75wt.% feldspar, 20wt.% quartz and 5wt.% kaolin. It was prepared by sintering the mixture at different temperatures (1100-1250°C). The optimum sintering conditions gave a relatively higher density (2.47g/cm(3)) and excellent mechanical properties. The three point flexural strength (3PFS) and Martens micro-hardness of dental porcelains were 149MPa and 2600MPa, respectively. This obtained 3PFS value is more than four times greater than that of hydroxyapatite (HA) value (about 37MPa) sintered under the same conditions. However, the sintering temperature was lowered by about 25 and 50°C for 3 and 5wt.% B2O3 additions, respectively. But, it did not improve furthermore the samples density and their mechanical properties. It has also been found that B2O3 additions provoke a glass matrix composition variation which delays the leucite formation during sintering. Copyright © 2016 Elsevier B.V. All rights reserved.

Digital Smile Design concept delineates the final potential result of crown lengthening and porcelain veneers to correct a gummy smile.

Science.gov (United States)

Trushkowsky, Richard; Arias, David Montalvo; David, Steven

Prior to initiating any treatment, it is necessary to visualize the desired outcomes. It then becomes possible to formulate the steps required to achieve this result. Digital Smile Design (DSD) utilizes patient input and information gathered through diagnostic procedures to create an esthetic treatment scheme. In the case presented here, the NYUCD Esthetic Evaluation Form, intraoral and extraoral photographs, mounted diagnostic casts, physical examination, and radiographs were the diagnostic modalities. The gathered information served as a starting point for a wax-up and intraoral mock-up. This case report demonstrates how the DSD served as a template for crown lengthening procedures and design of the final porcelain veneer restorations.

[The use of computer-aided colorimeter in porcelain-fused-to-metal (PFM) crowns among patients with special colored teeth].

Science.gov (United States)

Fu, Yuan-fei; Weng, Wei-min

2004-02-01

To evaluate the roll of ShadeEye-NCC, a computer-aided colorimeter, in Porcelain-Fused-to-Metal crowns among patients with special colored Teeth. The first step was to choose the proper patients. The next was to use the colorimeter to measure the base shade of tooth and fabricate the PFM crowns according to the recipe given by the colorimeter. At last, the effects of the PFM crowns were evaluated subjectively by patients and doctor. The satisfaction rates of patients and doctor were 83.7% and 81.4% respectively, there was no significant difference between the two rates. The computer-aided colorimeter can offer good base shade recipe for fabricating PFM crowns of patients with special colored teeth.

Provenance and indirect dating study on Hongzhou Kiln porcelains by INAA

International Nuclear Information System (INIS)

Feng, X.Q.; Feng, S.L.; Fan, C.S.; Zhang, W.J.; Quan, K.S.

2005-01-01

Hongzhou Kiln is one of the six leading celadon kilns in Tang Dynasty and plays an important role in the history of Chinese ceramics for its diverse decoration styles and innovative technology. Archaeologists divided Hongzhou Kiln production into 8 periods, i.e. Eastern Han and Eastern Wu, Western Jin, Eastern Jin, Southern Dynasties, Sui, Early Tang, Middle Tang, Late Tang and Five Dynasties. Up to now, 26 kiln sites have been discovered and excavated. A study on the chemical composition of the porcelains of different periods and provenance will help to know the developing process of Hongzhou celadon such as variation of raw materials, recipes, manufacturing technology, causes of prosperity and decline, etc. Over 200 sherds were collected and their body samples were analyzed by INAA. The compositional differences between samples with the same period but different provenance were observed. The contents of Na, Rb, Ba, Fe, Th, U, etc were found to be different among samples from different periods, which implies they may be used to identify the manufacturing age. The analytical data were further processed by principal component analysis (PCA). The statistical results show that all the sherds can be classified into 5 groups, (1) Eastern Han and Eastern Wu; (2) Western Jin, Eastern Jin and Southern Dynasties; (3) Sui; (4) Early Tang and Middle Tang; (5) Late Tang and Five Dynasties.

Hydrodynamic cavitation to improve bulk fluid to surface mass transfer in a nonimmersed ultraviolet system for minimal processing of opaque and transparent fluid foods.

Science.gov (United States)

Milly, P J; Toledo, R T; Chen, J; Kazem, B

2007-11-01

Ultraviolet (UV)-induced chemical reactions and inactivation of microorganisms in transparent and opaque fluids are strongly dependent upon the homogenous exposure of the target species to the UV irradiation. Current UV technologies used in water disinfection and food preservation applications have limited efficacy due to suspended particles shading target species. An Ultraviolet-Shockwave Power Reactor (UV-SPR) consisting of an inner rotating rotor and a stationary quartz housing and 2 end plates was used to induce 'controlled cavitation.' Eight UV low-pressure mercury lamps spaced uniformly were installed lengthwise around the quartz housing periphery. A KI to I(3) (-)chemical dosimeter for UV was used to quantify photons received by fluid in the annular space of the SPR. UV dose (J/m(2)) increased from 97 J/m(2) at 0 rpm to over 700 J/m(2) for SPR speeds above 2400 rpm. Inactivation of E. coli 25922 in apple juice and skim milk in the UV-SPR at exit temperatures below 45 degrees C was greater than 4.5 and 3 logs, respectively. The UV-SPR system proved successful in increasing the mass transfer of transparent and opaque fluid to the UV irradiated surface.

Silk, porcelain and lacquer: China and Japan and their trade with Western Europe and the New World, 1500-1644. A survey of documentary and material evidence

OpenAIRE

Llorens Planella, Maria Teresa (Teresa Canepa)

2015-01-01

This dissertation focused on the prolific early European trade and consumption of three Asian manufactured goods: Chinese silk and porcelain, and Japanese lacquer in the sixteenth and early seventeenth centuries, and has shown how the material cultures of late Ming China and Momoyama/early Edo Japan became inextricably linked with the West. Multiple sources provided new and unexpected documentary and material evidence of this trade by the Iberian Kingdoms of Portugal and Spain, and the tradin...

Porcelain Bladder as a Result of Urinary Schistosomiasis. Presentation of a Clinical Case with a Multidisciplinary Approach

Directory of Open Access Journals (Sweden)

Osmel Chávez Troya

2017-02-01

Full Text Available Uro-genital schistosomiasis is one of the parasite infections suffered by inhabitants of underdeveloped countries. This disease, as some other parasite infections, is increasing its incidence in some other as a consequence of higher population mobility. A case of a 35 year old woman is presented who was admitted to Malange General Hospital complaining of hypo-gastric pain, chills and final intermittent hematuria she had had for two monhs. After some lab tests, it was confirmed the presence of Schistosomas eggs in a urine sample and calcification of the bladder in porcelain form observed in a simple abdominal radiography. With the diagnosis of urinary schistosomiasis, she was treated with praziquantel at 40 mg per kg in a single dose. The patient came back a week later and afterwards for follow up. She is currently cured and doing her routines.

Rehabilitation of a patient with amelogenesis imperfecta using porcelain veneers and CAD/CAM polymer restorations: A clinical report.

Science.gov (United States)

Saeidi Pour, Reza; Edelhoff, Daniel; Prandtner, Otto; Liebermann, Anja

2015-01-01

The complete dental rehabilitation of patients with a vertical dimension loss (VDL) caused by structural enamel deficits associated with amelogenesis imperfecta (AI) represents a difficult challenge for restorative teams. Accurate analysis and treatment planning that includes esthetic and functional evaluations and adequate material selection are important prerequisites for successful results. Long-term provisional restorations play an important role in exploring and elucidating the patients' esthetic demands and functional needs. Restorative treatment options can vary from requiring only oral hygiene instructions to extensive dental restorations that include composite fillings, ceramic veneers, metal-ceramic, or all-ceramic crowns. This case report describes a full-mouth rehabilitation of a patient with amelogenesis imperfecta including the case planning, bite replacement, preparation, and restoration setting steps with an experimental CAD/CAM polymer and porcelain veneers.

Measurement of thermal transmittance of opaque facade wall relationship with meteorological conditions

Directory of Open Access Journals (Sweden)

Antunović Biljana S.

2015-01-01

Full Text Available This paper presents the results of measurements of thermal transmittance or as otherwise called U-value [W/m2⋅K] of opaque facade wall of preschool institution built in 1977. The building has an incomplete technical documentation according to which considered wall was built of brick and masonry mortar. Thermal characteristics of the incorporated materials have not been specified. Considering that in the period of building construction JUS standards was used, a possible range of calculated U-vales was obtained (1,241-1,404 W/m2·K. Measurements were performed in accordance with ISO 9869 during three time periods with the resulting U-values (1,269±0,276 W/m2·K; 1,025±0,175 W/m2·K; 1,200±0,212 W/m2·K that do not differ from each other within experimental uncertainty. Furthermore, the correlation of the measured U-values and meteorological conditions that prevailed during the measurements was analyzed. In the second measurement period, the average values of the total cloud cover and low cloud cover were less, and the average duration of sunshine was longer than in the other two measurement periods.

Evaluation of the potential of waste processing of secondary kaolin of Para for use in porcelain

International Nuclear Information System (INIS)

Junior, V.G.L.; Fernandes, L.L.; Fagury Neto, E.; Rabelo, A.A.

2012-01-01

The kaolin waste evaluated is characterized as secondary due be coming from the steps of centrifugation, magnetic separation, bleaching and filtering, which gives a ratio which provides a significant residue, about 26% of their gross, that is intended for embankments. This study aimed to evaluate the potential of reusing the kaolin waste processing from Imerys RCC in the region of Barcarena (PA) in formulation of ceramic bodies for porcelain tiles production, seeking to property of maximum water absorption of 0.5 % for this type of product. The residue from the production of kaolin had been previously characterized by X-ray diffraction and there is a significant amount of kaolinite concentration. After the ceramic processing to obtain the test specimens with different amounts of residue replacing the kaolin, these were sintered using 1200, 1220 and 1240 °C for 2 hours. The formulations were evaluated by water absorption, linear firing shrinkage and modulus of rupture at a three-point bending setup of the pieces produced. (author)

Damage Maps of Veneered Zirconia under Simulated Mastication

Science.gov (United States)

Kim, Jae-Won; Kim, Joo-Hyung; Janal, Malvin N.; Zhang, Yu

2016-01-01

Zirconia based restorations often fracture from chipping and/or delamination of the porcelain veneers. We hypothesize that veneer chipping/delamination is a result of the propagation of near-contact induced partial cone cracks on the occlusal surface under mastication. Masticatory loading involves the opposing tooth sliding along the cuspal inner incline surface with an applied biting force. To test this hypothesis, flat porcelain veneered zirconia plates were cemented to dental composites and cyclically loaded (contact–slide–liftoff) at an inclination angle as a simplified model of zirconia based restorations under occlusion. In the light of in-situ observation of damage evolution in a transparent glass/zirconia/polycarbonate trilayer, postmortem damage evaluation of porcelain/zirconia/composite trilayers using a sectioning technique revealed that deep penetrating occlusal surface partial cone fracture is the predominant fracture mode of porcelain veneers. Clinical relevance is discussed. PMID:19029080

Enamel thickness after preparation of tooth for porcelain laminate.

Science.gov (United States)

Pahlevan, Ayoub; Mirzaee, Mansoreh; Yassine, Esmaeil; Ranjbar Omrany, Ladan; Hasani Tabatabaee, Masumeh; Kermanshah, Hamid; Arami, Sakineh; Abbasi, Mehdy

2014-07-01

In this investigation the thickness of enamel in the gingival, middle, and incisal thirds of the labial surface of the anterior teeth were measured regarding preparation of the teeth for porcelain laminate veneers. Part one, 20 extracted intact human maxillary central and lateral incisors ten of each were selected. The teeth were imbedded in autopolimerize acrylic resin. Cross section was preformed through the midline of the incisal, middle and cervical one-third of the labial surface of the teeth. The samples were observed under reflected stereomicroscope and the thickness of enamel was recorded. Part II, the effect of different types of preparation on dentin exposure was evaluated. Thirty maxillary central incisor teeth were randomly divided into two groups: A: Knife-edge preparation. B: Chamfer preparation. All samples were embedded in autopolimerize acrylic resin using a silicon mold. The samples were cut through the midline of the teeth. The surface of the samples were polished and enamel and dentin were observed under the stereomicroscope. Data were analyzed by ANOVA-one way test. The results of this study showed that the least enamel thickness in the central incisor was 345 and in lateral incisor is 235 μ this thickness is related to the one-third labial cervical area. Maximum thickness in maxillary central and lateral incisors in the one-third labial incisal surface was 1260 μ and 1220μ, respectively. In the second part of the study, the tendency of dentinal exposure was shown with the chamfer preparation, but no dentinal exposure was found in the knife-edge preparation. The differences between groups were significant (p<0.05). The knowledge of enamel thickness in different part of labial surface is very important. The thickness of enamel in the gingival area does not permit a chamfer preparation. The knife edge preparation is preferable in gingival area.

Enamel thickness after preparation of tooth for porcelain laminate.

Directory of Open Access Journals (Sweden)

Ayoub Pahlevan

2014-08-01

Full Text Available In this investigation the thickness of enamel in the gingival, middle, and incisal thirds of the labial surface of the anterior teeth were measured regarding preparation of the teeth for porcelain laminate veneers.Part one, 20 extracted intact human maxillary central and lateral incisors ten of each were selected. The teeth were imbedded in autopolimerize acrylic resin. Cross section was preformed through the midline of the incisal, middle and cervical one-third of the labial surface of the teeth. The samples were observed under reflected stereomicroscope and the thickness of enamel was recorded. Part II, the effect of different types of preparation on dentin exposure was evaluated. Thirty maxillary central incisor teeth were randomly divided into two groups: A: Knife-edge preparation. B: Chamfer preparation. All samples were embedded in autopolimerize acrylic resin using a silicon mold. The samples were cut through the midline of the teeth. The surface of the samples were polished and enamel and dentin were observed under the stereomicroscope.Data were analyzed by ANOVA-one way test. The results of this study showed that the least enamel thickness in the central incisor was 345 and in lateral incisor is 235 μ this thickness is related to the one-third labial cervical area. Maximum thickness in maxillary central and lateral incisors in the one-third labial incisal surface was 1260 μ and 1220μ, respectively. In the second part of the study, the tendency of dentinal exposure was shown with the chamfer preparation, but no dentinal exposure was found in the knife-edge preparation. The differences between groups were significant (p<0.05.The knowledge of enamel thickness in different part of labial surface is very important. The thickness of enamel in the gingival area does not permit a chamfer preparation. The knife edge preparation is preferable in gingival area.

An in vitro study to evaluate the difference in shade between commercially available shade guides and glazed porcelain.

Science.gov (United States)

Manimaran, P; Sadan, D Sai

2016-10-01

Smile is one of the most important interactive communication skills of a person. A smile is the key factor for an aesthetic appearance. Hence aesthetics is one of the motivating factor for the patients to seek dental care. Correction of unaesthetic appearance gives a positive effect to the self esteem of the patient. The aim of this study was to compare the difference in the shade between the commercially available shade guides namely Vita Classical And Ivoclar Chromascop and the fired porcelain samples fabricated using Vita Zahnfabrik VMK 95 and Ivoclar Classic Materials respectively. The objective of this study was to obtain a matching brand of material that has a particular shade tab among the brands used. To conclude, Ivoclar material matched the chromascop shade guide better than the vita material matched the vita classic shade guide.

Study of alumosilicate porcelains: Sol-gel preparation, characterization and erosion evaluated by gravimetric method

International Nuclear Information System (INIS)

Bogdanoviciene, Irma; Jankeviciute, Audrone; Pinkas, Jiri; Beganskiene, Aldona; Kareiva, Aivaras

2008-01-01

In this paper, the sol-gel synthesis and characteristic properties of kalsilite-type alumosilicates (KAlSiO 4 and K 0.5 Na 0.5 AlSiO 4 ) are reported. The polycrystalline powders were characterized by thermal analysis (TG/DTA), powder X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM). Single-phase kalsilite oxides have been obtained after annealing precursor gels for 5 h in the temperature range of 750-850 deg. C. It was demonstrated that crystallinity of the samples slightly depends on the temperature of annealing. From the results obtained, it could be concluded that the KAlSiO 4 solids are composed of the volumetric plate-like grains with no regular size (from 5 μm to 30 μm at 750 deg. C and around 5-50 μm at 850 deg. C). Larger crystallites for mixed potassium-sodium kalsilite have formed (from 10 μm to 80 μm at 750 deg. C and >100 μm at 850 deg. C) in comparison with potassium kalsilite samples). The erosion of obtained dental porcelain samples stored in saliva, beer and Coca-Cola was compared

Blinded comparison of faecal loading on plain radiography versus radio-opaque marker transit studies in the assessment of constipation

Energy Technology Data Exchange (ETDEWEB)

Cowlam, S. [Sunderland Royal Hospital, Sunderland (United Kingdom); Vinayagam, R.; Khan, U.; Marsden, S.; Minty, I.; Moncur, P.; Bain, I. [University Hospital of North Durham, Durham (United Kingdom); Yiannakou, Y.J. [University Hospital of North Durham, Durham (United Kingdom)], E-mail: yan.yiannakou@cddft.nhs.uk

2008-12-15

Aim: To compare faecal loading on plain radiography versus radio-opaque marker transit studies in the assessment of constipation. Methods: The study group was a convenience sample of patients attending the Durham Constipation Clinic. All patients underwent transit studies according to an established protocol, and severity of constipation was assessed contemporaneously using a validated questionnaire (PAC-SYM). Transit studies were performed using radio-opaque markers that were ingested over 3 consecutive days, with a radiograph taken on the fourth day. Digital images of the radiograph were digitally altered to remove all traces of the transit markers without affecting the underlying pattern of faecal loading. Four observers assessed faecal loading independently; two clinicians (C1 and C2) and two radiologists (R1 and R2). C1 and R1 used a previously described formal scoring method of assessing faecal loading, whereas C2 and R2 assessed the images as if they were in a clinic or reporting session, grading the faecal loading as mild, moderate, or severe. Results: One hundred patients were recruited out of 186 presenting in a 2-year period. All patients completed assessments. The correlation between observers was only fair to moderate (r ranging from 0.34-0.51). There were some surprisingly marked disagreements in 10-18% of assessments. The correlation between faecal loading and transit was weak for all observers (r ranging from 0.261-0.311). Symptom severity did not correlate with faecal loading. Conclusion: These results suggest that there is considerable inter-observer variation in the radiological assessment of faecal loading, irrespective of the training or method used by the observer, and that there is very poor correlation with colonic transit. The diagnosis of constipation, and the assessment of severity, is best performed clinically.

Blinded comparison of faecal loading on plain radiography versus radio-opaque marker transit studies in the assessment of constipation

International Nuclear Information System (INIS)

Cowlam, S.; Vinayagam, R.; Khan, U.; Marsden, S.; Minty, I.; Moncur, P.; Bain, I.; Yiannakou, Y.J.

2008-01-01

Aim: To compare faecal loading on plain radiography versus radio-opaque marker transit studies in the assessment of constipation. Methods: The study group was a convenience sample of patients attending the Durham Constipation Clinic. All patients underwent transit studies according to an established protocol, and severity of constipation was assessed contemporaneously using a validated questionnaire (PAC-SYM). Transit studies were performed using radio-opaque markers that were ingested over 3 consecutive days, with a radiograph taken on the fourth day. Digital images of the radiograph were digitally altered to remove all traces of the transit markers without affecting the underlying pattern of faecal loading. Four observers assessed faecal loading independently; two clinicians (C1 and C2) and two radiologists (R1 and R2). C1 and R1 used a previously described formal scoring method of assessing faecal loading, whereas C2 and R2 assessed the images as if they were in a clinic or reporting session, grading the faecal loading as mild, moderate, or severe. Results: One hundred patients were recruited out of 186 presenting in a 2-year period. All patients completed assessments. The correlation between observers was only fair to moderate (r ranging from 0.34-0.51). There were some surprisingly marked disagreements in 10-18% of assessments. The correlation between faecal loading and transit was weak for all observers (r ranging from 0.261-0.311). Symptom severity did not correlate with faecal loading. Conclusion: These results suggest that there is considerable inter-observer variation in the radiological assessment of faecal loading, irrespective of the training or method used by the observer, and that there is very poor correlation with colonic transit. The diagnosis of constipation, and the assessment of severity, is best performed clinically

Effect of two kinds of porcelain crown on AST, ALP, TNF-α, IL-8, GP-x and MDA levels in gingival crevicular fluid

Directory of Open Access Journals (Sweden)

Ya-Ling Wang

2016-09-01

Full Text Available Objective: To investigate the effect of two kinds of porcelain crown on AST, ALP, TNF-α, IL-8, GP-x and MDA levels in gingival crevicular fluid. Methods: A total of 80 patients with dental porcelain crowns at front teeth during February 2013 to February 2016 were randomly divided into cobalt-chromium alloy PFM group (n=40 and gold alloy PFM group (n=40. After 6 months, the amount of gingival crevicular fluid, GI, PD, AST, ALP, TNF-α, IL-8, GP-x and MDA levels in gingival crevicular fluid were recorded and analyzed. Results: There were no differences in amount of gingival crevicular fluid, GI and PD before treatment of the two groups (P>0.05. After treatment, the amount of gingival crevicular fluid, GI and PD of the two groups were significantly higher than before treatment (P0.05. After treatment, the AST, ALP, TNF-α, IL-8 and MDA levels in gingival crevicular fluid of the two groups were significantly higher than before treatment (P<0.05, but that of the gold alloy PFM group were significantly lower than cobalt-chromium alloy PFM group (P<0.05. After treatment, the GP-x level in gingival crevicular fluid of the two groups were significantly lower than before treatment (P<0.05, but that of the gold alloy PFM group were significantly higher than cobalt-chromium alloy PFM group (P<0.05. Conclusions: Gold alloy PFM can significantly reduce the AST, ALP, TNF-α, IL-8 and MDA levels in gingival crevicular fluid, improve the GP-x level in gingival crevicular fluid, shows better biocompatibility and clinical outcomes than cobalt-chromium alloy PFM.

Environmental and human health assessment of life cycle of nanoTiO2 functionalized porcelain stoneware tile.

Science.gov (United States)

Pini, Martina; Bondioli, Federica; Montecchi, Rita; Neri, Paolo; Ferrari, Anna Maria

2017-01-15

Recently, there has been a rise in the interest in nanotechnology due to its enormous potential for the development of new products and applications with higher performance and new functionalities. However, while nanotechnology might revolutionize a number of industrial and consumer sectors, there are uncertainties and knowledge gaps regarding toxicological effects of this emerging science. The goal of this research concerns the implementation into Life Cycle Assessment (LCA) of preliminary frameworks developed to evaluate human toxicity and exposure factors related to the potential nanoparticle releases that could occur during the life cycle steps of a functionalized building material. The present LCA case study examines the ecodesign of nanoTiO 2 functionalized porcelain stoneware tile production. The aim of this investigation is to manufacture new eco-friendly products in order to protect human health and ecosystem quality and to offer the market, materials with higher technological properties obtained by the addition of specific nanomaterials. Copyright © 2016 Elsevier B.V. All rights reserved.

An in vitro study to evaluate the difference in shade between commercially available shade guides and glazed porcelain

Directory of Open Access Journals (Sweden)

P Manimaran

2016-01-01

Full Text Available Introduction: Smile is one of the most important interactive communication skills of a person. A smile is the key factor for an aesthetic appearance. Hence aesthetics is one of the motivating factor for the patients to seek dental care. Correction of unaesthetic appearance gives a positive effect to the self esteem of the patient. Aim: The aim of this study was to compare the difference in the shade between the commercially available shade guides namely Vita Classical And Ivoclar Chromascop and the fired porcelain samples fabricated using Vita Zahnfabrik VMK 95 and Ivoclar Classic Materials respectively. Objectives: The objective of this study was to obtain a matching brand of material that has a particular shade tab among the brands used. Conclusion: To conclude, Ivoclar material matched the chromascop shade guide better than the vita material matched the vita classic shade guide.

Mössbauer analysis of the firing process of the sky-green glaze of the imitative ancient Chinese Ru porcelain

Science.gov (United States)

Songhua, Chen; Zhengyao, Gao; Guoju, Hu; Xiande, Chen

1994-12-01

The variation of the Mössbauer parameters of the imitative ancient Ru porcelain skygreen glaze with the firing conditions is studied in detail in the present paper. The Mössbauer spectra show that the sky-green glaze contains three kinds of iron minerals, i.e. the structural iron (Fe2+ and Fe3+); Fe2O3 and Fe3O4. The relative intensity of the paramagnetic peak Fe2+ increases and the magnetic ratio of the magnetic peak decreases with increasing temperature. Based on the variation of the quadrupole splitting ( QS) of the paramagnetic peak Fe2+, the phase transformation characteristics of the sky-green glaze in the firing process is discussed. The coloring mechanism of the sky-green glaze and the variation of its magnetism in the firing process are also investigated in the present paper.

Experimental and analytical studies on multiple tuned mass dampers for seismic protection of porcelain electrical equipment

Science.gov (United States)

Bai, Wen; Dai, Junwu; Zhou, Huimeng; Yang, Yongqiang; Ning, Xiaoqing

2017-10-01

Porcelain electrical equipment (PEE), such as current transformers, is critical to power supply systems, but its seismic performance during past earthquakes has not been satisfactory. This paper studies the seismic performance of two typical types of PEE and proposes a damping method for PEE based on multiple tuned mass dampers (MTMD). An MTMD damping device involving three mass units, named a triple tuned mass damper (TTMD), is designed and manufactured. Through shake table tests and finite element analysis, the dynamic characteristics of the PEE are studied and the effectiveness of the MTMD damping method is verified. The adverse influence of MTMD redundant mass to damping efficiency is studied and relevant equations are derived. MTMD robustness is verified through adjusting TTMD control frequencies. The damping effectiveness of TTMD, when the peak ground acceleration far exceeds the design value, is studied. Both shake table tests and finite element analysis indicate that MTMD is effective and robust in attenuating PEE seismic responses. TTMD remains effective when the PGA far exceeds the design value and when control deviations are considered.

Evolution of the constructive adobe system in the Porcelain Industrial Unit of Vista Alegre (1937-1945

Directory of Open Access Journals (Sweden)

Alice Ruano

2010-01-01

Full Text Available The urban nucleus of the Porcelain Factory of Vista Alegre reveals a special interest in terms of the evolution of the traditional adobe construction in the town of Ílhavo, located in the district of Aveiro. Presenting a structured philosophy of intervention in the territory since its very beginning, it possesses a rich heritage in the field of construction and architecture. The measures planned and implemented in the second phase of Vista Alegre growth reporting its beginning to the ends of the 30's, and along the 40's, confirm it both in the rehabilitation, extension and new constructions in adobe masonry. Those measures were implemented during the structural changes of the Industrial Unit administration that only until this period belonged to the family of its founder. These changes creates one of the focus of innovation in the region, with new construction strategies and solutions in adobe buildings, which will prolonged the period of use of this construction system, noticeable in buildings dated of 1958 in the Vista Alegre and at least in 1970 in the town.

Characterization of opaque2 modifier QTLs and candidate genes in recombinant inbred lines derived from the K0326Y quality protein maize inbred

KAUST Repository

Holding, David R.

2010-11-13

Quality protein maize (QPM) is a high lysine-containing corn that is based on genetic modification of the opaque2 (o2) mutant. In QPM, modifier genes convert the starchy endosperm of o2 to the vitreous phenotype of wild type maize. There are multiple, unlinked o2 modifier loci (Opm) in QPM and their nature and mode of action are unknown. We previously identified seven Opm QTLs and characterized 16 genes that are differentially up-regulated at a significant level in K0326Y QPM, compared to the starchy endosperm mutant W64Ao2. In order to further characterize these Opm QTLs and the genes up-regulated in K0326Y QPM, we created a population of 314 recombinant inbred lines (RILs) from a cross between K0326Y QPM and W64Ao2. The RILs were characterized for three traits associated with endosperm texture: vitreousness, density and hardness. Genetic linkage analysis of the RIL population confirmed three of the previously identified QTLs associated with o2 endosperm modification in K0326Y QPM. Many of the genes up-regulated in K0326Y QPM showed substantially higher levels of expression in vitreous compared with opaque RILs. These included genes associated with the upstream regulation of the ethylene response pathway, and a gene encoding a regulatory subunit of pyrophosphate-dependent fructose-6-phosphate 1-phosphotransferase, an adaptive enzyme of the glycolytic pathway. © 2010 Springer-Verlag.

A performance study of radio-opaque personal protective fabrics for the reduction of transmittance of gamma-rays and neutrons

International Nuclear Information System (INIS)

Corcoran, E.C.; William Forest; Robert Horton; Kelly, D.G.; Kristine Mattson; Curtis McDonald; Nielsen, K.S.; Kristin Topping; Weir, R.D.; Andre Yonkeu

2012-01-01

Commercial radio-opaque combat (CRC) fabrics, for incorporation into personal protective equipment used by first responders and armed forces, are marketed as having the ability to provide a level of protection against specific types of radiation. For a CRC material, a standard combat uniform and a multi-layered chemical, biological, radiological, nuclear (CBRN) protective material, the present work examines chemical composition and radiation protection against gamma-rays and neutron fluxes. Significant reduction in gamma-ray transmittance occurs only for the CRC fabric (46-514 keV) with gamma-ray attenuation coefficients of 3.10 to 2 g -1 . Reduction in neutron transmittance, for all three fabrics, could not be assessed with certainty as the measured transmittance was obscured by large statistical uncertainties. (author)

Effect of provisional cements on shear bond strength of porcelain laminate veneers.

Science.gov (United States)

Altintas, Subutay Han; Tak, Onjen; Secilmis, Asli; Usumez, Aslihan

2011-08-01

The purpose of this study was to evaluate the effect of three provisional cements and two cleaning techniques on the final bond strength of porcelain laminate veneers. The occlusal third of the crowns of forty molar teeth were sectioned and embedded in autopolymerizing acrylic resin. Dentin surfaces were polished and specimens were randomly divided into four groups (n=10). Provisional restorations were fabricated and two provisional restorations were cemented onto each tooth. Restorations were fixed with one of three different provisional cements: eugenol-free provisional cement (Cavex), calcium hydroxide (Dycal), and light-cured provisional cement (Tempond Clear). Provisional restorations were removed with either a dental explorer and air-water spray, or a cleaning bur (Opticlean). In the control group, provisional restorations were not used on the surfaces of specimens. IPS Empress 2 ceramic discs were luted with a dual-cured resin cement (Panavia F). Shear bond strength was measured using a universal testing machine. Data were statistically analyzed by ANOVA, Tukey's HSD and Dunnett tests. Surfaces were examined by scanning electronic microscopy. Significant differences were found between the control group and both the light-cured provisional cement groups and the eugenol-free provisional cement-cleaning bur group (Pprovisional cement showed the lowest bond strength values. Selection of the provisional cement is an important factor in the ultimate bond strength of the final restoration. Calcium hydroxide provisional cement and cleaning with a dental explorer are advisable.

Influence of the barite tenors of the Jaicos, Piaui, Brazil, clays on the ceramic properties of electric insulator porcelains; Influencia dos teores de barita das argilas de Jaicos, Piaui, Brasil nas propriedades ceramicas de porcelana de isoladores eletricos

Energy Technology Data Exchange (ETDEWEB)

Correa, W.L.P. [Escola SENAI Mario Amato, Sao Bernardo do Campo, SP (Brazil); Lima, M.B. [Faculdade Sao Bernardo, SP (Brazil); Carvalho, F.M.S. [Universidade de Sao Paulo (USP), SP (Brazil). Inst. de Geociencias

2009-07-01

The clays of the Municipality of Jaicos, Piaui, has been used as raw materials for the manufacture of insulators for company located in the municipality of Pedreira - Sao Paulo. It can be noticed in the clay blocks and consolidated, 'lenses' of barite. The mineralogical composition of clay and the nature of these 'lenses' were studied by chemical analysis, X-ray diffraction for mineralogical characterization. The clays are composed primarily by kaolinite, quartz, and some amount of illite and orthoclase. The presence of orthoclase does believe in a recent deposition of these clays. The 'lenses' were characterized as barite, BaSO{sub 4}. To check the influence of barite in the composition of bodies of porcelain to insulators made up six compositions with different levels of barite, obtained their own clay. It applies, then the tests of ceramic fracture to bending, water absorption, apparent porosity to determine the effect of the introduction of barite in the compositions. (author)

Evaluation of an optimized shade guide made from porcelain powder mixtures.

Science.gov (United States)

Wang, Peng; Wei, Jiaqiang; Li, Qing; Wang, Yining

2014-12-01

Color errors associated with current shade guides and problems with color selection and duplication are still challenging for restorative dentists. The purpose of this study was to evaluate an optimized shade guide for visual shade duplication. Color distributions (L*, a*, and b*) of the maxillary left central incisors of 236 participants, whose ages ranged from 20 to 60, were measured with a spectrophotometer. Based on this color map, an optimized shade guide was designed with 14 shade tabs evenly distributed within the given color range of the natural incisors. The shade tabs were fabricated with porcelain powder mixtures and conventional laboratory procedures. A comparison of shade duplication by using the optimized and Vitapan Classical shade guides was conducted. Thirty Chinese participants were involved, and the colors of the left maxillary incisors were selected by using 2 shade guides. Metal ceramic crowns were fabricated according to the results of the shade selection. The colors of the shade tabs, natural teeth, and the ceramic crowns were measured with a spectrophotometer. The color differences among the natural teeth, the shade tabs, and the corresponding metal ceramic crowns were calculated and analyzed (α=.017). Significant differences were found in both phases of shade determination and shade duplication (P<.017). The total number of color errors with the optimized shade guide was 3.5, which was significantly less than that of Vitapan, 5.1 (P<.001). The optimized shade guide system improved performance not only in the color selection phase but also in the color of the fabricated crowns. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Near-field reflection backscattering apertureless optical microscopy: Application to spectroscopy experiments on opaque samples, comparison between lock-in and digital photon counting detection techniques

International Nuclear Information System (INIS)

Diziain, S.; Bijeon, J.-L.; Adam, P.-M.; Lamy de la Chapelle, M.; Thomas, B.; Deturche, R.; Royer, P.

2007-01-01

An apertureless scanning near-field optical microscope (ASNOM) in reflection backscattering configuration is designed to conduct spectroscopic experiments on opaque samples constituted of latex beads. The ASNOM proposed takes advantage of the depth-discrimination properties of confocal microscopes to efficiently extract the near-field optical signal. Given their importance in a spectroscopic experiment, we systematically compare the lock-in and synchronous photon counting detection methods. Some results of Rayleigh's scattering in the near field of the test samples are used to illustrate the possibilities of this technique for reflection backscattering spectroscopy

Near-field reflection backscattering apertureless optical microscopy: Application to spectroscopy experiments on opaque samples, comparison between lock-in and digital photon counting detection techniques

Energy Technology Data Exchange (ETDEWEB)

Diziain, S. [Institut Charles Delaunay, CNRS FRE 2848, Laboratoire de Nanotechnologie et d' Instrumentation Optique, Universite de technologie de Troyes, 12 rue Marie Curie, BP 2060, 10010 Troyes cedex (France); Bijeon, J.-L. [Institut Charles Delaunay, CNRS FRE 2848, Laboratoire de Nanotechnologie et d' Instrumentation Optique, Universite de technologie de Troyes, 12 rue Marie Curie, BP 2060, 10010 Troyes cedex (France)]. E-mail: bijeon@utt.fr; Adam, P.-M. [Institut Charles Delaunay, CNRS FRE 2848, Laboratoire de Nanotechnologie et d' Instrumentation Optique, Universite de technologie de Troyes, 12 rue Marie Curie, BP 2060, 10010 Troyes cedex (France); Lamy de la Chapelle, M. [Institut Charles Delaunay, CNRS FRE 2848, Laboratoire de Nanotechnologie et d' Instrumentation Optique, Universite de technologie de Troyes, 12 rue Marie Curie, BP 2060, 10010 Troyes cedex (France); Thomas, B. [Institut Charles Delaunay, CNRS FRE 2848, Laboratoire de Nanotechnologie et d' Instrumentation Optique, Universite de technologie de Troyes, 12 rue Marie Curie, BP 2060, 10010 Troyes cedex (France); Deturche, R. [Institut Charles Delaunay, CNRS FRE 2848, Laboratoire de Nanotechnologie et d' Instrumentation Optique, Universite de technologie de Troyes, 12 rue Marie Curie, BP 2060, 10010 Troyes cedex (France); Royer, P. [Institut Charles Delaunay, CNRS FRE 2848, Laboratoire de Nanotechnologie et d' Instrumentation Optique, Universite de technologie de Troyes, 12 rue Marie Curie, BP 2060, 10010 Troyes cedex (France)

2007-01-15

An apertureless scanning near-field optical microscope (ASNOM) in reflection backscattering configuration is designed to conduct spectroscopic experiments on opaque samples constituted of latex beads. The ASNOM proposed takes advantage of the depth-discrimination properties of confocal microscopes to efficiently extract the near-field optical signal. Given their importance in a spectroscopic experiment, we systematically compare the lock-in and synchronous photon counting detection methods. Some results of Rayleigh's scattering in the near field of the test samples are used to illustrate the possibilities of this technique for reflection backscattering spectroscopy.

Formulation and characterization of structural lightweight concrete containing residues of porcelain tile polishing, tire rubber and limestone

Directory of Open Access Journals (Sweden)

Z. L. M. Sampaio

Full Text Available Abstract The recent increase in the construction industry has transformed concrete into an ideal choice to recycle a number of residues formerly discarded into the environment. Among various products, porcelain tile polishing, limestone and tire rubber residues are potential candidates to replace the fine aggregate of conventional mixtures. The aim of this study was to investigate the effect of the addition of varying contents of these residues in lightweight concrete where expanded clay replaced gravel. To that end, slump, compressive strength, density, void ratio, porosity and absorption tests were carried out. The densities of all concrete formulations studied were 10% lower to that of lightweight concrete (<1.850 kg/m³. Nevertheless, mixes containing 10 to 15% of combined residues reduced absorption, void ratio and porosity, at least 17% lower compared to conventional concrete. The strength of such formulations reached 27 MPa at 28 days with consistency of 9 to 12 cm, indicating adequate consistency and increased strength. In addition, the combination of low porosity, absorption and voids suggested improved durability.

Determination of dose rate from natural radionuclide in porcelain dental materials

International Nuclear Information System (INIS)

Nouri, A.D.; El-Zourgany, A.; Elmashat, Alia; El-Masri, Karima

2010-01-01

There are three main aims that make this study particularly important and interesting to radiometric studies. Firstly, it will provides information on the concentration composition of natural and the associated man-made radioactivity of imported dental porcelain materials to be used by most dental laboratories in Great Jamahiriya. Since these materials do not pass radiation inspection tests before their entry or use and there is a large variety of supply source of these dental materials to be used for all dental works on Libyan patients, anomalies can be identified easily. Secondly, the analysis of selective elemental abundance (U, Th, and K ) and dose rate calculations may be used to calculate effective dose rates to dental laboratory technicians and also to the patient who will be using these specific materials. This research project will provide the first results of such measurements and the corresponding average annual effective dose rates equivalent to the patients using these materials and also to the dental technician and doctors work in the various dental laboratories that make use of these materials in their daily work. A total number of 30 dental powder samples were collected from a number of dental laboratories around Tripoli area will be analyzed. In this research project, the results from this preliminary survey regarding Th, U and K elemental concentrations in a wide variety of dental materials by means of high-resolution X-ray spectrometry will be presented. Further results from these investigations concerning activity concentrations and the associated dose rates, effective dose and the committed dose due to the use of these materials are going to be calculated and compared with other published data elsewhere and recommendation of their use will be derived accordingly. (author)

Wear properties of dental ceramics and porcelains compared with human enamel.

Science.gov (United States)

D'Arcangelo, Camillo; Vanini, Lorenzo; Rondoni, Giuseppe D; De Angelis, Francesco

2016-03-01

Contemporary pressable and computer-aided design/manufacturing (CAD/CAM) ceramics exhibit good mechanical and esthetic properties. Their wear resistance compared with human enamel and traditional gold based alloys needs to be better investigated. The purpose of this in vitro study was to compare the 2-body wear resistance of human enamel, gold alloy, and 5 different dental ceramics, including a recently introduced zirconia-reinforced lithium silicate ceramic (Celtra Duo). Cylindrical specimens were fabricated from a Type III gold alloy (Aurocast8), 2 hot pressed ceramics (Imagine PressX, IPS e.max Press), 2 CAD/CAM ceramics (IPS e.max CAD, Celtra Duo), and a CAD/CAM feldspathic porcelain (Vitablocs Mark II) (n=10). Celtra Duo was tested both soon after grinding and after a subsequent glaze firing cycle. Ten flat human enamel specimens were used as the control group. All specimens were subjected to a 2-body wear test in a dual axis mastication simulator for 120000 loading cycles against yttria stabilized tetragonal zirconia polycrystal cusps. The wear resistance was analyzed by measuring the vertical substance loss (mm) and the volume loss (mm(3)). Antagonist wear (mm) was also recorded. Data were statistically analyzed with 1-way ANOVA tests (α=.05). The wear depth (0.223 mm) of gold alloy was the closest to that of human enamel (0.217 mm), with no significant difference (P>.05). The greatest wear was recorded on the milled Celtra Duo (wear depth=0.320 mm), which appeared significantly less wear resistant than gold alloy or human enamel (Pceramics did not statistically differ in comparison with the human enamel. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Radio-opaque ethylcellulose-ethanol is a safe and efficient sclerosing agent for venous malformations

International Nuclear Information System (INIS)

Dompmartin, Anne; Barrellier, Marie-Therese; Blaizot, Xavier; Chene, Yannick; Gaillard, Cathy; Theron, Jacques; Hammer, Frank; Labbe, Daniel; Leroyer, Robert; Chedru, Valerie; Ollivier, Catherine; Vikkula, Miikka; Boon, Laurence M.

2011-01-01

To evaluate the efficacy and safety of gelified ethanol, a newly developed sclerosing agent for slow-flow vascular malformations. Seventy-nine sclerotherapy procedures were performed on 44 patients with 37 venous malformations, 2 glomuvenous malformations, 2 lymphatic malformations, 2 lymphatico-venous malformations, and 1 Klippel-Trenaunay syndrome. The median injected volume was 1.00 mL/site of injection. Effects of sclerotherapy on pain, functional and cosmetic disturbance were statistically evaluated with a final result score. Local and systemic complications were recorded. The mean Visual Analogue Scores were 5.20 ± 2.81 before and 1.52 ± 1.25 after treatment (p < 0.001). Functional and aesthetic improvement was achieved in 31/35 patients (89%) and in 33/41 (80%), respectively. Minor local side effects included necrosis with or without issue of ethylcellulose, palpable residue, and hematoma. No systemic side-effects occurred. Per mL used, radio-opaque gelified ethanol is at least as effective as absolute ethanol. No systemic complication was observed, as only a low dose of ethanol was injected. Indications for sclerotherapy can be widened to areas with higher risk for local side effects (hands and periocular region), as ethanol is trapped in the lesion. Careful injection procedure is though necessary, because only a limited amount of ethylcellulose can be used per puncture. (orig.)

Propriedades microestruturais de argamassas de cimento Portland com adições minerais e poliméricas utilizadas na fixação de porcelanato Study of the influence of additions on the adherence between polymer-modified mortars and porcelain stoneware tiles

Directory of Open Access Journals (Sweden)

A. E. F. S. Almeida

2006-09-01

characteristics of porcelain tiles, its application on building façades requires special attention, since this material differs from conventional ceramics and because façades are exposed to weathering that can damage ceramic revetments. Literature presents lots of researches about adhesive mortars properties employing ceramic tiles with higher water absorption (more than 3%. In a different way, we find about porcelain stoneware tiles with almost 0% water absorption, that is the most important cause of detachments between the back side of porcelain tiles and the mortar, for the reason that there is no mechanical adherence how occurs for porous ceramic tiles. The present study shows some properties of mortars with polymer and silica fume additions to fix porcelain tile, intending to solve the problems about the lack of adherence. The combination of polymer and silica fume to mortars results in excellent properties, which are ideal for repairs and revestments requiring high performance, thus justifying its study for the fixing of porcelain tiles. Procedures were carried out following the specifications of the NBR 14082 standard. This article presents adherence values for mortars containing different amounts of added polymer and silica, indicating the applicability of these mortars as construction material. Microstructural properties were based on mercury intrusion porosimetry tests and scanning electron microscopy of fractured samples.

Shear bond strengths of an indirect composite layering material to a tribochemically silica-coated zirconia framework material.

Science.gov (United States)

Iwasaki, Taro; Komine, Futoshi; Fushiki, Ryosuke; Kubochi, Kei; Shinohara, Mitsuyo; Matsumura, Hideo

2016-01-01

This study evaluated shear bond strengths of a layering indirect composite material to a zirconia framework material treated with tribochemical silica coating. Zirconia disks were divided into two groups: ZR-PRE (airborne-particle abrasion) and ZR-PLU (tribochemical silica coating). Indirect composite was bonded to zirconia treated with one of the following primers: Clearfil Ceramic Primer (CCP), Clearfil Mega Bond Primer with Clearfil Porcelain Bond Activator (MGP+Act), ESPE-Sil (SIL), Estenia Opaque Primer, MR. Bond, Super-Bond PZ Primer Liquid A with Liquid B (PZA+PZB), and Super-Bond PZ Primer Liquid B (PZB), or no treatment. Shear bond testing was performed at 0 and 20,000 thermocycles. Post-thermocycling shear bond strengths of ZR-PLU were higher than those of ZR-PRE in CCP, MGP+Act, SIL, PZA+PZB, and PZB groups. Application of silane yielded better durable bond strengths of a layering indirect composite material to a tribochemically silica-coated zirconia framework material.

Raman analysis of cobalt blue pigment in blue and white porcelain: A reassessment

Science.gov (United States)

Jiang, Xiaochenyang; Ma, Yanying; Chen, Yue; Li, Yuanqiu; Ma, Qinglin; Zhang, Zhaoxia; Wang, Changsui; Yang, Yimin

2018-02-01

Cobalt blue is a famous pigment in human history. In the past decade it is widely reported that the cobalt aluminate has been detected in ancient ceramics as blue colorant in glaze, yet the acquired Raman spectra are incredibly different from that of synthesised references, necessitating a reassessment of such contradictory scenario with more accurate analytic strategies. In this study, micro-Raman spectroscopy (MRS) and scanning electron microscopy (SEM) in association with energy dispersive spectrometry (EDS) were performed on under-glaze cobalt pigments from one submerged blue and white porcelain shard dated from Wanli reign (1573-1620 CE) of Ming dynasty (1365-1644 CE) excavated at Nan'ao I shipwreck off the southern coast of China. The micro-structural inspection reveals that the pigment particles have characteristics of small account, tiny size, heterogeneously distribution, and more importantly, been completely enwrapped by well-developed anorthite crystals in the glaze, indicating that the signals recorded in previous publications are probably not from cobalt pigments themselves but from outside thickset anorthite shell. The further spectromicroscopic analyses confirm this presumption when the accurate spectra of cobalt aluminate pigment and surrounding anorthite were obtained separately with precise optical positioning. Accordingly, we reassess and clarify the previous Raman studies dedicated to cobalt blue pigment in ancient ceramics, e.g. cobalt blue in celadon glaze, and in turn demonstrate the superiority and necessity of coupling spectroscopic analysis with corresponding structure observation, especially in the characterization of pigments from complicated physico-chemical environment like antiquities. Thus, this study promotes a better understanding of Raman spectroscopy study of cobalt blue pigments in art and archaeology field.

An integral geometry lemma and its applications: The nonlocality of the Pavlov equation and a tomographic problem with opaque parabolic objects

Science.gov (United States)

Grinevich, P. G.; Santini, P. M.

2016-10-01

Written in the evolutionary form, the multidimensional integrable dispersionless equations, exactly like the soliton equations in 2+1 dimensions, become nonlocal. In particular, the Pavlov equation is brought to the form v t = v x v y - ∂ x -1 ∂ y [ v y + v x 2], where the formal integral ∂ x -1 becomes the asymmetric integral - int_x^∞ {dx'} . We show that this result could be guessed using an apparently new integral geometry lemma. It states that the integral of a sufficiently general smooth function f( X, Y) over a parabola in the plane ( X, Y) can be expressed in terms of the integrals of f( X, Y) over straight lines not intersecting the parabola. We expect that this result can have applications in two-dimensional linear tomography problems with an opaque parabolic obstacle.

Study of flux and mud stone with potential for using in porcelainized stoneware tile compositions; Estudo de fundente e argilito com potencial para uso em formulacoes de porcelanato

Energy Technology Data Exchange (ETDEWEB)

Hoffmann, F.S.; Santos, G. dos; Morelli, M.R., E-mail: felipesh@gmail.com [Departamento de Engenharia de Materiais, Universidade Federal de S. Carlos - UFSCar, S. Carlos, SP (Brazil)

2012-04-15

The porcelain tile is distinguished in the current market for ceramic tiles, with excellent technical and esthetic characteristics. In the present study traditional ceramic raw materials were selected and a standard formulation conventionally reported in the literature was adopted aiming to replace the melting phase (feldspar) of the composition for a raw material that forms liquid phase at high temperature, and replacement of the clay fraction by a mudstone of lower refractoriness. The aim of this study was to evaluate the use of these materials as alternative techniques and lower cost, since, in a mass of porcelain tile, the amount of flux is very large (representing approximately 50% of total raw materials used). The nepheline syenite was the natural raw material selected to replace the feldspar due to the fact that it belongs to the family of feldspathoids, and has similar physicochemical characteristics, therefore, a high fluxing efficiency. To replace the clay fraction was chosen a mudstone naturally occurring, abundant in the region of Santa Gertrudes, SP. Substitutions to the feldspar and clay fraction were completely and/or partially by means of combinations between the flux and mud stones. The masses were processed from the mixing of powders, wet milling, drying, disagglomeration, compaction and firing. In addition to the vitrification curves, techniques such as dilatometry, measurements of porosity, flexure strength test, electron microscopy and X-ray diffraction were used to characterize the material after firing at various temperatures. The results showed that, in principle, it is possible the combination of raw materials such as nepheline and mudstone to replace potassium feldspar and S. Simao clay, as they provide the vitrification at lower temperatures. Compositions with both materials showed lower values of water absorption (<0.1%) and high mechanical strength (> 45 MPa), despite higher pyroplastic strain at 1150 deg C (author)

Emerging technology and techniques

Directory of Open Access Journals (Sweden)

Gopi Naveen Chander

2015-01-01

Full Text Available A technique of fabricating feldspathic porcelain pressable ingots was proposed. A 5 ml disposable syringe was used to condense the powder slurry. The condensed porcelain was sintered at 900΀C to produce porcelain ingots. The fabricated porcelain ingots were used in pressable ceramic machines. The technological advantages of pressable system improve the properties, and the fabricated ingot enhances the application of feldspathic porcelain.

Relative translucency of six all-ceramic systems. Part II: core and veneer materials.

Science.gov (United States)

Heffernan, Michael J; Aquilino, Steven A; Diaz-Arnold, Ana M; Haselton, Debra R; Stanford, Clark M; Vargas, Marcos A

2002-07-01

STATEMENT OF PROBLEM All-ceramic core materials with various strengthening compositions have a range of translucencies. It is unknown whether translucency differs when all-ceramic materials are fabricated similarly to the clinical restoration with a veneered core material. This study compared the translucency of 6 all-ceramic materials veneered and glazed at clinically appropriate thicknesses. Core specimens (n = 5 per group) of Empress dentin, Empress 2 dentin, In-Ceram Alumina, In-Ceram Spinell, In-Ceram Zirconia, and Procera AllCeram were fabricated as described in Part I of this study and veneered with their corresponding dentin porcelain to a final thickness of 1.47 +/- 0.01 mm. These specimens were compared with veneered Vitadur Alpha opaque dentin (as a standard), a clear glass disc (positive control), and a high-noble metal-ceramic alloy (Porc. 52 SF) veneered with Vitadur Omega dentin (negative control). Specimen reflectance was measured with an integrating sphere attached to a spectrophotometer across the visible spectrum (380 to 700 nm); 0-degree illumination and diffuse viewing geometry were used. Measurements were repeated after a glazing cycle. Contrast ratios were calculated from the luminous reflectance (Y) of the specimens with a black (Yb) and a white backing (Yw) to give Yb/Yw with CIE illuminant D65 and a 2-degree observer function (0.0 = transparent, 1.0 = opaque). One-way analysis of variance and Tukey's multiple-comparison test were used to analyze the data (P<.05). Significant differences in contrast ratios were found among the ceramic systems tested when they were veneered (P<.0001) and after the glazing cycle (P<.0001). Significant changes in contrast ratios (P<.0001) also were identified when the veneered specimens were glazed. Within the limitations of this study, a range of translucency was identified in the veneered all-ceramic systems tested. Such variability may affect their ability to match natural teeth. The glazing cycle resulted

Archaelogical Excavations of the Gardens and Interior Areas of Houses B and C of the Southeast Row Houses Fort Michilimackinac, Michigan.

Science.gov (United States)

1981-08-01

porcelain fragments recovered were Group I, Chinese Export Porcelain . No evidence of Group II, English Porcelain , was present. There were 40 fragments...earthenware, stoneware and porcelain . Distribution of colonial ceramics by unit and level appears in Appendices 2 31 and 3. Therefore, only classes and...unidentifiable fragments of stoneware. Similar to the earthenware, they were not identified because of being burned or too small. Class C Porcelain All

Lente intra-ocular opaca em diplopia intratável: relato de caso Opaque intraocular lens in intractable diplopia: case report

Directory of Open Access Journals (Sweden)

Fernanda Teixeira Krieger

2006-08-01

Full Text Available Diplopia intratável tem sido descrita em várias situações. Métodos convencionais como prismas e correção cirúrgica do estrabismo falham em neutralizá-la. O objetivo do trabalho é documentar o caso de uma paciente com estrabismo de longa data, cuja diplopia deteriorou-se ao longo dos anos, e não foi possível resolução com cirurgia, prisma, e oclusão com óculos e lente de contato com pupila opaca. A paciente foi então submetida à facoemulsificação com implante de lente intra-ocular opaca que atingiu o objetivo desejado.Intractable diplopia has been described in many situations but poor results are the rule with standard treatment modalities. The authors report a case of a woman with long-standing strabismus and diplopia who failed to improve following surgery, prism, and occlusive spectacles or contact lenses. Then, she was submitted to phacoemulsification and opaque intraocular lens implantation, which successfully neutralized diplopia.

Development of a falling ball rheometer with applications to opaque systems: measurements of the rheology of suspensions of rods

International Nuclear Information System (INIS)

Powell, R.L.; Mondy, L.A.; Stoker, G.G.; Milliken, W.J.; Graham, A.L.

1989-01-01

With falling ball rheometry, we have measured the apparent relative viscosity of suspensions of large, neutrally buoyant, rigid rods in a viscous Newtonian fluid, while approximately maintaining the rods in a randomly oriented configuration. A new technique for measuring the time of flight of a ball between two positions is used. This computerized technique, based upon an eddy current detector, enables us to determine the position of a metallic (nonmagnetic) ball falling through an opaque suspension, with high accuracy (less than 1.5% error). The rods for the suspensions had a nominal aspect ratio of 10 and experiments were carried out at a single volume fraction, 0.05. Two populations of rods were used to having nominal diameters of 1.5875 mm and 3.175 mm. To within the errors of these experiments, suspensions from both populations had the same relative viscosity, with the overall average being 1.457. This viscosity was significantly different from that of a similar suspension (volume fraction=0.05) of rods of nominal aspect ratio 20 and it agreed well with theoretical results for the viscosity of a dilute suspension of randomly oriented rods

Improved color matching of metal ceramic restorations. Part II: Procedures for visual communication.

Science.gov (United States)

Sorensen, J A; Torres, T J

1987-12-01

Most ceramic restorations are fabricated in a location remote from the dental office. Successful fabrication of matching life-like ceramic restorations necessitates a collaborative effort between the dentist and the ceramist. To meet the demands for visual communication of shade and surface texture, the following steps are recommended. 1. A means of communicating and recording surface texture that facilitates blending the restorations with the natural dentition should be used. 2. The system should use an esthetics prescription form that functions with the Shade Indicator Chart system to relate the shade of opaque, body, and incisal porcelains and their arrangement to the ceramist. 3. An easily made identification mold to form shade tabs is needed. 4. Identification shade tabs should be made to verify and document shade formulations selected with the Shade Indicator Chart system. 5. Methods for precisely mapping and reproducing individual characterization patterns are needed. This information permits the visualization of the end result, allowing the artistic expression of the ceramist to create vital-appearing restorations intrinsically and in harmony with the natural dentition.

Analysis of vertical marginal discrepancy in feldspathic porcelain crowns manufactured with different CAD/CAM systems: Closed and open.

Science.gov (United States)

Kricheldorf, Fabio; Bueno, Cleuber Rodrigo de Souza; Amaral, Wilson da Silva; Junior, Joel Ferreira Santiago; Filho, Hugo Nary

2018-01-01

The objective of this study is to compare the marginal adaptation of feldspathic porcelain crowns using two computer-aided design/computer-aided manufacturing systems, one of them is open and the other is closed. Twenty identical titanium abutments were divided into two groups: open system (OS), where ceramic crowns were created using varied equipment and software, and closed system (CS), where ceramic crowns were created using the CEREC system. Through optical microscopy analysis, we assess the marginal adaptation of the prosthetic interfaces. The data were subjected to the distribution of normality and variance. The t -test was used for the analysis of the comparison factor between the groups, and the one-way ANOVA was used to compare the variance of crown analysis regions within the group. A significance level of 5% was considered for the analyses. There was a significant difference between the systems ( P = 0.007), with the CS group having the higher mean (23.75 μm ± 3.05) of marginal discrepancy when compared to the open group (17.94 μm ± 4.77). Furthermore, there were no differences in marginal discrepancy between the different points between the groups ( P ≥ 0.05). The studied groups presented results within the requirements set out in the literature. However, the OS used presented better results in marginal adaptation.

Influence of coping design on the cervical color of ceramic crowns.

Science.gov (United States)

Paniz, Gianluca; Kang, Ki-Ho; Kim, Yongjeong; Kumagai, Naota; Hirayama, Hiroshi

2013-12-01

The replication of natural teeth, especially with single-tooth restorations, represents a challenge. Similar to metal ceramic crowns, different designs of zirconia substructures have been suggested to improve the esthetic results of zirconia ceramic crowns. The purpose of the study was to analyze the color of the cervical portion of single zirconia ceramic crowns fabricated with different zirconia coping designs. The color, measured on the CIELAB color scale, of 3 different groups of restorations (n=10) fabricated with zirconia coping (Lava) and feldspathic porcelain (Noritake Super Porcelain) was analyzed with a spectrophotometer. Conventional zirconia crowns with zirconia facial margins were compared with ceramic crowns with porcelain facial margins and either a horizontal reduction of the zirconia coping (1.0 mm reduction) or an additional vertical reduction (1.0 mm additional reduction). The 3 groups, each with a different coping extension, were examined with a 1-way ANOVA and the Fisher exact test, and the differences of the groups were evaluated by applying ΔE thresholds (α=.05). The mean color difference among all the groups was not clinically significant (ΔEcolor differences were present between the 2 porcelain butt margin groups of crowns (ΔE=1.06, between group H and V). Increased differences were present between the zirconia margin group and the porcelain butt margin group (ΔE=2.54 between group C and H; ΔE=2.41 between group C and V). Lab* values were examined in all the groups of crowns to determine the clinical implications. Within the limitation of the study, no significant differences were present among the tested groups of crowns. Nevertheless, although some differences were present between the zirconia margin group and the porcelain butt margin group, reduced differences were present between the 2 different cutback designs. Copyright © 2013 Editorial Council for the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights

Effect of porcelain polishing addition of waste in properties blocks ceramic; Efeito da adicao do residuo de polimento de porcelanato nas propriedades de blocos ceramicos

Energy Technology Data Exchange (ETDEWEB)

Santana, G.L.; Barbosa Neto, M.C.; Campos, L.F.; Macedo, D.A; Dutra, R.P.S., E-mail: geovanalira1@gmail.com [Universidade Federal da Paraiba (UFPB), PB (Brazil)

2016-07-01

This work has as objective the study of the technological properties of ceramic blocks with addition of residue porcelain polishing. The test samples are produced with clay base, where the waste is introduced in concentrations of 10% and 20% by mass, to evaluate its influence on the properties of the ceramic block. All these materials were characterized by determining their chemical composition (XRF) and X-ray diffraction Sintering was performed at temperatures of 850 ° C, 950 ° C and 1100 ° C with a heating rate of 2 ° C / me and 60 minutes of landing. After this, there was obtained the technological properties of the samples such as: Loss on fire, the burning linear shrinkage, water absorption, porosity and density, as well as, mechanical strength properties through the flexural strength test. The results show that the addition of waste influenced both the technological properties, the mechanical properties evaluated in this study. (author)

NAA study on characteristics and sources of raw materials of celadon bodies from Qingliangsi kiln and Zhanggongxiang kiln

International Nuclear Information System (INIS)

Wu Zhanjun; Zhao Weijuan; Lu Xiaoke; Li Guoxia; Guo Min; Xie Jianzhong; Qiu Xia; Feng Songlin

2007-01-01

Thirty-seven samples of ancient Chinese Ru porcelain bodies unearthed from Qingliangsi kiln (containing 32 Ru official porcelain bodies and 5 Ru folk porcelain bodies), thirty-two samples of ancient celadon bodies from Zhanggongxiang kiln, and fourteen samples of modern mineral, were selected and analyzed by neutron activation analysis (NAA) method. Twenty-three elements were measured. The data of these elemental contents were processed by scatter analysis and principle component analysis methods in order to determine the characteristics and sources of the raw materials of the celadon porcelain bodies from the foregoing two kilns. The results show that Fe, Ce, Ba, Ta, Th, La, Sm and Cr are the fingerprint elements to distinguish the ancient Ru official porcelain bodies from ancient celadon bodies of Zhanggongxiang kiln. The sources of the raw material of the ancient Ru official porcelain bodies from Qingliangsi kiln are more concentrated and stable than those from Zhanggongxiang kiln. The Ru folk porcelain bodies and the Ru official porcelain bodies from Qingliangsi kiln have the same provenance, both sources of which are local. The raw material origins of the ancient celadon bodies from Zhanggongxiang kiln is a little dispersed and the compositions of the raw material are different from the Ru porcelains, but the distance is not far away from each other. (authors)

X-Ray diffraction and scanning electron microscopy-energy dispersive spectroscopic analysis of ceramõmetal interface at different firing temperatures

Directory of Open Access Journals (Sweden)

Monika Saini

2010-01-01

Full Text Available Objective: Porcelain chipping from porcelain fused to metal restoration has been Achilles heel till date. There has been advent of newer ceramics in past but but none of them has been a panacea for Porcelain fracture. An optimal firing is thus essential for the clinical success of the porcelain-fused to metal restoration. The aim of the present study was to evaluate ceramo-metal interface at different firing temperature using XRD and SEM-EDS analysis. Clinical implication of the study was to predict the optimal firing temperature at which porcelain should be fused with metal in order to possibly prevent the occasional failure of the porcelain fused to metal restorations. Materials and Methods: To meet the above-mentioned goal, porcelain was fused to metal at different firing temperatures (930-990°C in vacuum. The microstructural observations of interface between porcelain and metal were evaluated using X-ray diffraction and scanning electron microscopy with energy dispersive spectroscopy. Results: Based on the experimental investigation of the interaction zone of porcelain fused to metal samples, it was observed that as the firing temperature was increased, the pores became less in number as well as the size of the pores decreased at the porcelain/metal interface upto 975°C but increased in size at 990°C. The least number of pores with least diameter were found in samples fired at 975°C. Several oxides like Cr 2 O 3 , NiO, and Al 2 O 3 and intermetallic compounds (CrSi 2 , AlNi 3 were also formed in the interaction zone. Conclusions : It is suggested that the presence of pores may trigger the crack propagation along the interface, causing the failure of the porcelain fused to metal restoration during masticatory action.

Fracture and shear bond strength analyses of different dental veneering ceramics to zirconia

International Nuclear Information System (INIS)

Diniz, Alexandre C.; Nascimento, Rubens M.; Souza, Julio C.M.; Henriques, Bruno B.; Carreiro, Adriana F.P.

2014-01-01

The purpose of this work was to evaluate the interaction of different layering porcelains with zirconia via shear bond strength test and microscopy. Four different groups of dental veneering porcelains (VM9, Zirkonzanh, Ceramco, IPS) were fused onto forty zirconia-based cylindrical substrates (8 mm in diameter and 12 mm in height) (n = 10), according to the manufacturer's recommendations. Additionally, layered dental porcelain (D-sign, Ivoclar) was fired on ten Ni–Cr cylindrical substrates Shear bond strength tests of the veneering porcelain to zirconia or Ni–Cr were carried out at a crosshead speed of 0.5 mm/min. After the shear bond tests, the interfaces were analyzed by scanning electron microscopy (SEM). The fracture type exhibited by the different systems was also assessed. The results were statistically analyzed by ANOVA at a significant level of p < .05. The shear bond strength values of the porcelain-to-NiCr interfaces (25.3 ± 7.1 MPa) were significantly higher than those recorded for the following porcelain-to-zirconia systems: Zirkonzanh (18.8 ± 1 MPa), Ceramco (18.2 ± 4.7 MPa), and IPS (16 ± 4.5 MPa). However, no significant differences were found in the shear bond strength values between the porcelain-to-NiCr and porcelain (VM9)-to-zirconia (23.2 ± 5.1 MPa) groups (p > .05). All-ceramic interfaces revealed mixed failure type, cohesive in the porcelain and adhesive at the interface. This study demonstrated that all-ceramic systems do not attain yet the same bond strength standards equivalent to metal–ceramic systems. Therefore, despite the esthetic appeal of all-ceramic restorations, the adhesion between the porcelain and zirconia framework is still an issue considering the long term success of the restoration. - Highlights: • This study assessed the shear bond strength of different porcelains to zirconia. • The porcelain Vita VM9 showed a high shear bond strength to zirconia. • The fracture surface of all-ceramic systems revealed

Fracture and shear bond strength analyses of different dental veneering ceramics to zirconia

Energy Technology Data Exchange (ETDEWEB)

Diniz, Alexandre C. [School of Dentistry (DOD), Division of Prosthodontics, Universidade Federal do Rio Grande do Norte -UFRN, 59056-000, Natal (Brazil); Nascimento, Rubens M. [Materials Engineering Department, Universidade Federal do Rio Grande do Norte - UFRN, Natal (Brazil); Souza, Julio C.M. [Centre for Mechanics and Materials Technologies - CT2M, Department of Mechanical Engineering (DEM), Universidade do Minho, Campus Azurém, 4800-058, Guimarães (Portugal); Henriques, Bruno B. [Materials Engineering Department, Universidade Federal do Rio Grande do Norte - UFRN, Natal (Brazil); Centre for Mechanics and Materials Technologies - CT2M, Department of Mechanical Engineering (DEM), Universidade do Minho, Campus Azurém, 4800-058, Guimarães (Portugal); Carreiro, Adriana F.P., E-mail: adrianadafonte@hotmail.com [School of Dentistry (DOD), Division of Prosthodontics, Universidade Federal do Rio Grande do Norte -UFRN, 59056-000, Natal (Brazil)

2014-05-01

The purpose of this work was to evaluate the interaction of different layering porcelains with zirconia via shear bond strength test and microscopy. Four different groups of dental veneering porcelains (VM9, Zirkonzanh, Ceramco, IPS) were fused onto forty zirconia-based cylindrical substrates (8 mm in diameter and 12 mm in height) (n = 10), according to the manufacturer's recommendations. Additionally, layered dental porcelain (D-sign, Ivoclar) was fired on ten Ni–Cr cylindrical substrates Shear bond strength tests of the veneering porcelain to zirconia or Ni–Cr were carried out at a crosshead speed of 0.5 mm/min. After the shear bond tests, the interfaces were analyzed by scanning electron microscopy (SEM). The fracture type exhibited by the different systems was also assessed. The results were statistically analyzed by ANOVA at a significant level of p < .05. The shear bond strength values of the porcelain-to-NiCr interfaces (25.3 ± 7.1 MPa) were significantly higher than those recorded for the following porcelain-to-zirconia systems: Zirkonzanh (18.8 ± 1 MPa), Ceramco (18.2 ± 4.7 MPa), and IPS (16 ± 4.5 MPa). However, no significant differences were found in the shear bond strength values between the porcelain-to-NiCr and porcelain (VM9)-to-zirconia (23.2 ± 5.1 MPa) groups (p > .05). All-ceramic interfaces revealed mixed failure type, cohesive in the porcelain and adhesive at the interface. This study demonstrated that all-ceramic systems do not attain yet the same bond strength standards equivalent to metal–ceramic systems. Therefore, despite the esthetic appeal of all-ceramic restorations, the adhesion between the porcelain and zirconia framework is still an issue considering the long term success of the restoration. - Highlights: • This study assessed the shear bond strength of different porcelains to zirconia. • The porcelain Vita VM9 showed a high shear bond strength to zirconia. • The fracture surface of all-ceramic systems revealed

Cellular ceramics made from porcelain tile polishing wastes: influence of sintering time; Ceramicas cellulares obtidas a partir de residuo de polimento de porcelanato: influencia do tempo de sinterizacao

Energy Technology Data Exchange (ETDEWEB)

Guimaraes, A.F.; Zanelatto, C.C.; Uggioni, E. [Universidade do Extremo Sul Catarinense (UNESC), Criciuma, SC (Brazil). Dept. de Engenharia de Materiais; Bernardin, A.M., E-mail: amb@unesc.ne [Servico Nacional de Aprendizagem Industrial, Tijucas, SC (Brazil). Tecnologia em Ceramica

2009-07-01

This paper deals with the physical, microstructural and mechanical characterization of cellular ceramics made from porcelain polishing wastes, which were expanded by the bubble formation technique during the sintering process. The microstructure, linear expansion, bulk density (mercury immersion) and mechanical behavior (compressive strength) were determined to characterize the glass foam obtained. Moreover, the porcellaneous residue was characterized by chemical and phase analyses, particle size (laser diffraction) and thermal behavior. As a result, the higher the soaking time during heat treatment at 1200 deg C the lower the density obtained for the cellular ceramic due to CO{sub 2} expansion, and lower the mechanical strength of the samples. The microstructure shows spherical cells and completely closed pores, resulting in a cheap way to obtain low density material with adequate mechanical strength, avoiding the disposal of wastes from the ceramic industry. (author)

Non-destructive characterization of oriental porcelain glazes and blue underglaze pigments using μ-EDXRF, μ-Raman and VP-SEM

Energy Technology Data Exchange (ETDEWEB)

Coutinho, M.L. [Universidade Nova de Lisboa, REQUIMTE-CQFB, Faculdade de Ciencias e Tecnologia, Caparica (Portugal); Universidade Nova de Lisboa, Departamento de Conservacao e Restauro, Faculdade de Ciencias e Tecnologia, Caparica (Portugal); Muralha, V.S.F. [Universidade Nova de Lisboa, Research Unit VICARTE, Vidro e Ceramica para as Artes, Faculdade de Ciencias e Tecnologia, Caparica (Portugal); Mirao, J. [Universidade de Evora, Laboratorio HERCULES, Evora (Portugal); Veiga, J.P. [Universidade Nova de Lisboa, CENIMAT/I3N, Departamento de Ciencia dos Materiais, Faculdade de Ciencias e Tecnologia, Caparica (Portugal)

2014-03-15

The study of ancient materials with recognized cultural and economic value is a challenge to scientists and conservators, since it is usually necessary an approach through non-destructive techniques. Difficulties in establishing a correct analytical strategy are often significantly increased by the lack of knowledge on manufacture technologies and raw materials employed combined with the diversity of decay processes that may have acted during the lifetime of the cultural artefacts. A non-destructive characterization was performed on the glaze and underglaze pigments from a group of Chinese porcelain shards dated from the late Ming Dynasty (1368-1644) excavated at the Monastery of Santa Clara-a-Velha in Coimbra (Portugal). Chemical analysis was performed using micro-energy dispersive X-ray fluorescence spectrometry (μ-EDXRF). Mineralogical characterization was achieved by Raman microscopy (μ-Raman) and observation of small-surface crystallization dark spots with a metallic lustre in areas with high pigment concentration was done by variable pressure scanning electron microscopy (VP-SEM). Cobalt aluminate was identified as the blue underglaze pigment and a comparison of blue and dark blue pigments was performed by the ratio of Co, Mn, and Fe oxides, indicating a compositional difference between the two blue tonalities. Manganese oxide compounds were also identified as colouring agents in dark blue areas and surface migration of manganese compounds was verified. (orig.)

Non-destructive characterization of oriental porcelain glazes and blue underglaze pigments using μ-EDXRF, μ-Raman and VP-SEM

International Nuclear Information System (INIS)

Coutinho, M.L.; Muralha, V.S.F.; Mirao, J.; Veiga, J.P.

2014-01-01

The study of ancient materials with recognized cultural and economic value is a challenge to scientists and conservators, since it is usually necessary an approach through non-destructive techniques. Difficulties in establishing a correct analytical strategy are often significantly increased by the lack of knowledge on manufacture technologies and raw materials employed combined with the diversity of decay processes that may have acted during the lifetime of the cultural artefacts. A non-destructive characterization was performed on the glaze and underglaze pigments from a group of Chinese porcelain shards dated from the late Ming Dynasty (1368-1644) excavated at the Monastery of Santa Clara-a-Velha in Coimbra (Portugal). Chemical analysis was performed using micro-energy dispersive X-ray fluorescence spectrometry (μ-EDXRF). Mineralogical characterization was achieved by Raman microscopy (μ-Raman) and observation of small-surface crystallization dark spots with a metallic lustre in areas with high pigment concentration was done by variable pressure scanning electron microscopy (VP-SEM). Cobalt aluminate was identified as the blue underglaze pigment and a comparison of blue and dark blue pigments was performed by the ratio of Co, Mn, and Fe oxides, indicating a compositional difference between the two blue tonalities. Manganese oxide compounds were also identified as colouring agents in dark blue areas and surface migration of manganese compounds was verified. (orig.)

Non-destructive characterization of oriental porcelain glazes and blue underglaze pigments using μ-EDXRF, μ-Raman and VP-SEM

Science.gov (United States)

Coutinho, M. L.; Muralha, V. S. F.; Mirão, J.; Veiga, J. P.

2014-03-01

The study of ancient materials with recognized cultural and economic value is a challenge to scientists and conservators, since it is usually necessary an approach through non-destructive techniques. Difficulties in establishing a correct analytical strategy are often significantly increased by the lack of knowledge on manufacture technologies and raw materials employed combined with the diversity of decay processes that may have acted during the lifetime of the cultural artefacts. A non-destructive characterization was performed on the glaze and underglaze pigments from a group of Chinese porcelain shards dated from the late Ming Dynasty (1368-1644) excavated at the Monastery of Santa Clara- a- Velha in Coimbra (Portugal). Chemical analysis was performed using micro-energy dispersive X-ray fluorescence spectrometry (μ-EDXRF). Mineralogical characterization was achieved by Raman microscopy (μ-Raman) and observation of small-surface crystallization dark spots with a metallic lustre in areas with high pigment concentration was done by variable pressure scanning electron microscopy (VP-SEM). Cobalt aluminate was identified as the blue underglaze pigment and a comparison of blue and dark blue pigments was performed by the ratio of Co, Mn, and Fe oxides, indicating a compositional difference between the two blue tonalities. Manganese oxide compounds were also identified as colouring agents in dark blue areas and surface migration of manganese compounds was verified.

Evaluation of performance of modified sodium lignosulfonate additives as reinforcing agent in porcelain stoneware tiles

Directory of Open Access Journals (Sweden)

Rastelli, E.

2010-10-01

Full Text Available A sodium salt of a modified lignosulfonate at different percentages was added to a porcelain stoneware suspension and the effects on the rheological properties of slips and on the mechanical properties of prepared samples were investigated. As the presence of sulfonates groups can change the stability of dispersion, a rheological characterisation was necessary to find the critical concentration to obtain well dispersed suspensions and high MOR values. The suspensions stability was tested by oscillatory measurements and the increase of elastic modulus in the suspension corresponded to a MOR and to Young’s modulus increase as well. Finally, to explain the results obtained by the mechanical characterisation of the prepared samples, a model drawing on the composite materials experience, is suggested.

Usando distintos porcentajes, se añadió sal de sodio de un lignosulfonato modificado, a una suspensión de gres porcelánico, y se investigaron los efectos sobre las propiedades reológicas de las suspensiones y sobre las propiedades mecánicas de las muestras preparadas. Debido a que la presencia de grupos de sulfonatos puede modificar la estabilidad de la dispersión, fue necesario realizar una caracterización reológica para averiguar la concentración crítica necesaria para la obtención de suspensiones bien dispersas y altos valores de MOR. Se analizó la estabilidad de las suspensiones por medio de mediciones oscilatorias y el incremento del módulo elástico en la suspensión que corresponde al incremento de un módulo MOR y de un módulo de Young también. Finalmente, para explicar los resultados obtenidos por medio de la caracterización mecánica de las muestras preparadas, se sugiere un modelo que parte de la experiencia con los materiales compuestos.

Mycobiota and co-occurrence of mycotoxins in South African maize-based opaque beer.

Science.gov (United States)

Adekoya, Ifeoluwa; Obadina, Adewale; Adaku, Cynthia Chilaka; De Boevre, Marthe; Okoth, Sheila; De Saeger, Sarah; Njobeh, Patrick

2018-04-02

Beer, a beverage consumed throughout the world, is mainly derived from cereals. In this study, fungal and mycotoxin contamination, as well as the physicochemical properties of maize-based opaque beer (umqombothi) obtained from the Gauteng province of South Africa, was investigated. The mean water activity, pH and total titratable acidity of the analysed beer samples were 0.91, 3.76 and 1.20% lactic acid, respectively. The investigation revealed Aspergillus, Penicillium, Phoma and Saccharomyces as the predominant fungal genera with a mean fungal load of 3.66 × 10 5  CFU/mL. Among the mycotoxigenic fungal species recovered, Aspergillus flavus had the highest incidence of 26%. Previously unreported strains such as P. chrysogenum strain AD25, A. sydowii strain AD 22 and A. tritici strain AD 11 were found. Furthermore, mycotoxin quantitative analysis via liquid chromatography-tandem mass spectrophotometry showed that deoxynivalenol was the dominant mycotoxin occurring in 84% of the samples. This was followed by enniatin B that occurred in 75% of samples ranging from 12 to 44 μg/L and fumonisin B 1 (FB 1 ) (incidence of 53% at a maximum level of 182 μg/L). Generally, there was low occurrence aflatoxins, whereas T-2, HT-2, nivalenol, zearalenone, 3- and 15-acetyl-deoxynivalenol were not detected. All the samples analysed had safe levels of mycotoxins tested but were contaminated by at least two mycotoxins that could pose some additive or synergistic health effects among consumers. On average: a 60 kg adult consuming 1-6 L/day of the beer was exposed to FB 1  + FB 2 at an estimated 2.20-13.20 μg/kg body weight/day. These values were far above the maximum tolerable daily intake of 2 μg/kg bw/day established by the Joint FAO/WHO Expert Committee on Food Additives (JECFA). The study demonstrates that consumption of umqombothi can significantly enhance dietary exposure to multiple mycotoxins among consumers, and therefore accentuates the need for

AN EXTREME ANALOGUE OF ϵ AURIGAE: AN M-GIANT ECLIPSED EVERY 69 YEARS BY A LARGE OPAQUE DISK SURROUNDING A SMALL HOT SOURCE

Energy Technology Data Exchange (ETDEWEB)

Rodriguez, Joseph E.; Stassun, Keivan G.; Lund, Michael B.; Conroy, Kyle E. [Department of Physics and Astronomy, Vanderbilt University, 6301 Stevenson Center, Nashville, TN 37235 (United States); Siverd, Robert J. [Las Cumbres Observatory Global Telescope Network, 6740 Cortona Drive, Suite 102, Santa Barbara, CA 93117 (United States); Pepper, Joshua [Department of Physics, Lehigh University, 16 Memorial Drive East, Bethlehem, PA 18015 (United States); Tang, Sumin [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Kafka, Stella [American Association of Variable Star Observers, 49 Bay State Road, Cambridge, MA 02138 (United States); Gaudi, B. Scott; Stevens, Daniel J.; Kochanek, Christopher S. [Department of Astronomy, The Ohio State University, Columbus, OH 43210 (United States); Beatty, Thomas G. [Department of Astronomy and Astrophysics, The Pennsylvania State University, 525 Davey Lab, University Park, PA 16802 (United States); Shappee, Benjamin J. [Carnegie Observatories, 813 Santa Barbara Street, Pasadena, CA 91101 (United States)

2016-05-01

We present TYC 2505-672-1 as a newly discovered and remarkable eclipsing system comprising an M-type red giant that undergoes a ∼3.45 year long, near-total eclipse (depth of ∼4.5 mag) with a very long period of ∼69.1 years. TYC 2505-672-1 is now the longest-period eclipsing binary system yet discovered, more than twice as long as that of the currently longest-period system, ϵ Aurigae. We show from analysis of the light curve including both our own data and historical data spanning more than 120 years and from modeling of the spectral energy distribution, both before and during eclipse, that the red giant primary is orbited by a moderately hot source ( T {sub eff} ≈ 8000 K) that is itself surrounded by an extended, opaque circumstellar disk. From the measured ratio of luminosities, the radius of the hot companion must be in the range of 0.1–0.5 R {sub ⊙} (depending on the assumed radius of the red giant primary), which is an order of magnitude smaller than that for a main sequence A star and 1–2 orders of magnitude larger than that for a white dwarf. The companion is therefore most likely a “stripped red giant” subdwarf-B type star destined to become a He white dwarf. It is, however, somewhat cooler than most sdB stars, implying a very low mass for this “pre-He-WD” star. The opaque disk surrounding this hot source may be a remnant of the stripping of its former hydrogen envelope. However, it is puzzling how this object became stripped, given that it is at present so distant (orbital semimajor axis of ∼24 au) from the current red giant primary star. Extrapolating from our calculated ephemeris, the next eclipse should begin in early UT 2080 April and end in mid UT 2083 September (eclipse center UT 2081 December 24). In the meantime, radial velocity observations would establish the masses of the components, and high-cadence UV observations could potentially reveal oscillations of the hot companion that would further constrain its evolutionary

Copper-silver ionization at a US hospital: interaction of treated drinking water with plumbing materials, aesthetics and other considerations

Science.gov (United States)

Tap water sampling and surface analysis of copper pipe/bathroom porcelain were performed to explore the fate of copper and silver during the first nine months of copper-silver ionization (CSI) applied to cold and hot water at a hospital in Cincinnati, Ohio. Ions dosed by CSI into...

Avaliação in vitro da força de união, através de teste de tração, de porcelana feldspática com diversos tratamentos superficiais à resina composta In vitro evaluation of the bonding strength of the composite resin to feldspathic porcelain with several surface treatments, applying a tensile strength test

Directory of Open Access Journals (Sweden)

Américo Mendes CARNEIRO JUNIOR

1999-07-01

Full Text Available Na busca da reprodução do aspecto dental, a porcelana se destaca entre os materiais restauradores. Desse modo, a utilização do material vem atualmente crescendo cada vez mais, e, com ela, a probabilidade de fraturas. Porém, uma falha nem sempre exige a troca da restauração: existe a possibilidade de um reparo com resina composta. Este trabalho se propôs a avaliar, in vitro, a força de união da resina composta à porcelana feldspática, quando efetuados os seguintes tratamentos superficiais na porcelana: asperização com instrumento cortante rotatório diamantado ou jateamento com óxido de alumínio de 50 micra, em aplicação isolada ou associada a condicionamento com ácido fosfórico, por 15 segundos, ou com ácido fluorídrico, por 1 ou por 4 minutos. Todos os espécimes foram previamente regularizados com lixa nº 220. Após os tratamentos superficiais, receberam o sistema de união adesivo para porcelana Scotchbond Multi-Purpose Plus Dental Adhesive System (3M. Feita a união com a resina composta (Restaurador Z100, 3M, foram armazenados em água destilada a 37ºC, em estufa, por 7 dias, e termociclados (600 ciclos de 1 minuto, entre 5 e 55ºC, sendo então submetidos a teste de tração. Pelos resultados obtidos, pôde-se concluir que ocorreu melhora na resistência à tração com todos os tratamentos propostos (em comparação ao observado no grupo controle, sem nenhum tratamento superficial. O jateamento produziu maior resistência de união que a asperização com instrumento cortante rotatório diamantado; mas, quando associados ao condicionamento com qualquer dos ácidos selecionados, independente do tempo de aplicação, não houve diferença estatística entre esses tratamentos.In the search for the recovery of the dental aspect, the porcelain stands out among restoring materials. The use of this material has increased considerably over the last years, therefore increasing the probability of fractures. Even so, not

In vitro wear of four ceramic materials and human enamel on enamel antagonist.

Science.gov (United States)

Nakashima, Jun; Taira, Yohsuke; Sawase, Takashi

2016-06-01

The purpose of the present study was to evaluate the wear of four different ceramics and human enamel. The ceramics used were lithium disilicate glass (e.max Press), leucite-reinforced glass (GN-Ceram), yttria-stabilized zirconia (Aadva Zr), and feldspathic porcelain (Porcelain AAA). Hemispherical styli were fabricated with these ceramics and with tooth enamel. Flattened enamel was used for antagonistic specimens. After 100,000 wear cycles of a two-body wear test, the height and volume losses of the styli and enamel antagonists were determined. The mean and standard deviation for eight specimens were calculated and statistically analyzed using a non-parametric (Steel-Dwass) test (α = 0.05). GN-Ceram exhibited greater stylus height and volume losses than did Porcelain AAA. E.max Press, Porcelain AAA, and enamel styli showed no significant differences, and Aadva Zr exhibited the smallest stylus height and volume losses. The wear of the enamel antagonist was not significantly different among GN-Ceram, e.max Press, Porcelain AAA, and enamel styli. Aadva Zr resulted in significantly lower wear values of the enamel antagonist than did GN-Ceram, Porcelain AAA, and enamel styli. In conclusion, leucite-reinforced glass, lithium disilicate glass, and feldspathic porcelain showed wear values closer to those for human enamel than did yttria-stabilized zirconia. © 2016 Eur J Oral Sci.

Study on the chemical composition features of Longquan celadon excavated from the Chuzhou site of Huai'an City in Jiangsu Province by EDXRF

Science.gov (United States)

Li, Li; Feng, Song-Lin; Feng, Xiang-Qian; Xu, Qing; Yan, Ling-Tong; Ma, Bo; Huo, Hua

2011-07-01

A mass of Longquan celadon shards were excavated from the Chuzhou site of Huai'an City in Jiangsu Province, China. These celadon shards were fired during the period of the Late Yuan Dynasty to the Tianshun era of the Ming Dynasty, as identified by archaeologists at Nanjing Museum. In order to research the chemical composition features of this ancient celadon porcelain, energy dispersive X-ray fluorescence (EDXRF) for non-destructive analysis was used to determine the chemical composition of the porcelain body and glaze in these shards. The results indicate that Ti and Fe in the body of Longquan celadon are characteristic elements which can distinguish porcelain produced during the Late Yuan Dynasty from those produced in the Ming Dynasties. The results of the principal component analysis (PCA) show that different body and glaze raw materials were used for the production of porcelain in different periods and the raw materials of the body and glaze are also different for various vessel shapes. The chemical compositions in the porcelain body of civilian ware are slightly different. The imperial and civilian Longquan celadon porcelains produced during the Hongwu era to the Tianshun era of the Ming Dynasty are distinguishable by the MnO, Fe2O3, Rb2O and SrO content in their porcelain glaze.

Use of rice straw ash as substitute of feldspar in triaxial porcelain; Cenizas del tamo de arroz como substituto del feldespato en la fabricacion de ceramica blanca

Energy Technology Data Exchange (ETDEWEB)

Alvaro Guzman, A.; Silverio Delvasto, A.; Enrique Sanchez, V.; Vicente Amigo, B.

2013-02-01

The substitution of raw materials for processing high energy consumption materials by agricultural and agro-industrial wastes causes a positive impacts on the environment preservation. One of these residues is rice straw, which according to FAO estimation, its annual production is about 600 million tons. In this research was studied the use of rice straw ash as substitute of the use of feldspar in the white ware production. Clay-feldspar-quartz porcelains are referred to as triaxial white ware. Specimens of semidry triaxial mixtures, where feldspar was substituted for different percentages of CTA, were prepared by uniaxial pressing, followed by drying and sintering. Physical and mechanical properties of sintered bodies were evaluated. The porosity and the compressive strength of the fired pieces do increase with additions of up to 75% of CTA in substitution of feldspar. Their mineralogical phases were determined by DRX and SEM; grains of quartz, and needles of primary and secondary mullite were identified in a vitreous phase. It was concluded that feldspar can be substituted positively by CTA in white ware pastes. (Author) 22 refs.

Aristocratic Sinomania: The SNM Museum Červený Kameň and its collection of Chinese porcelain (Vplyv sinománie na budovanie šľachtických zbierok – zbierka čínskeho porcelánu v SNM-Múzeu Červený Kameň

Directory of Open Access Journals (Sweden)

Nikola Maliňáková

2016-03-01

Full Text Available This paper analyzes the influence of Chinese culture on the lifestyle of European aristocrats which ranged from adoption of certain elements from the Chinese culture to an outright Sinomania which led to such fads as designing homes in the chinoiserie style or collecting Chinese artifacts, especially porcelain. The latter not only showed that the owner followed the latest fashions, but it also displayed their wealth and high social status. In this paper, we analyzed one such collection currently house in the SNM Musem Červený Kameň providing a detailed description of selected items

Moessbauer Studies in Chinese Archaeology: A Review

International Nuclear Information System (INIS)

Hsia Yuanfu; Huang Hongbo

2003-01-01

The Moessbauer effect has been applied to a wide variety of objects related to Chinese archaeology. Besides ceramic artifacts, materials like porcelain, glazes, bronzes, ancient coins, ancient mineral drugs, and even fossils were studied. This article reviews these applications with particular emphasis on the study of the famous terracotta warriors and horses of the Qin Dynasty.

Moessbauer Studies in Chinese Archaeology: A Review

Energy Technology Data Exchange (ETDEWEB)

Hsia Yuanfu; Huang Hongbo [Nanjing University, Department of Physics (China)

2003-09-15

The Moessbauer effect has been applied to a wide variety of objects related to Chinese archaeology. Besides ceramic artifacts, materials like porcelain, glazes, bronzes, ancient coins, ancient mineral drugs, and even fossils were studied. This article reviews these applications with particular emphasis on the study of the famous terracotta warriors and horses of the Qin Dynasty.

Mössbauer Studies in Chinese Archaeology: A Review

Science.gov (United States)

Hsia, Yuanfu; Huang, Hongbo

2003-09-01

The Mössbauer effect has been applied to a wide variety of objects related to Chinese archaeology. Besides ceramic artifacts, materials like porcelain, glazes, bronzes, ancient coins, ancient mineral drugs, and even fossils were studied. This article reviews these applications with particular emphasis on the study of the famous terracotta warriors and horses of the Qin Dynasty.

Fast-switching initially-transparent liquid crystal light shutter with crossed patterned electrodes

Directory of Open Access Journals (Sweden)

Joon Heo

2015-04-01

Full Text Available We propose an initially transparent light shutter using polymer-networked liquid crystals with crossed patterned electrodes. The proposed light shutter is switchable between the transparent and opaque states, and it exhibits a fast response time and a low operating voltage. In the transparent state, the light shutter has high transmittance; in the opaque state, it can block the background image and provides black color. We expect that the proposed light shutter can be applied to see-through displays and smart windows.

Quantitative tomographic measurements of opaque multiphase flows

Energy Technology Data Exchange (ETDEWEB)

GEORGE,DARIN L.; TORCZYNSKI,JOHN R.; SHOLLENBERGER,KIM ANN; O' HERN,TIMOTHY J.; CECCIO,STEVEN L.

2000-03-01

An electrical-impedance tomography (EIT) system has been developed for quantitative measurements of radial phase distribution profiles in two-phase and three-phase vertical column flows. The EIT system is described along with the computer algorithm used for reconstructing phase volume fraction profiles. EIT measurements were validated by comparison with a gamma-densitometry tomography (GDT) system. The EIT system was used to accurately measure average solid volume fractions up to 0.05 in solid-liquid flows, and radial gas volume fraction profiles in gas-liquid flows with gas volume fractions up to 0.15. In both flows, average phase volume fractions and radial volume fraction profiles from GDT and EIT were in good agreement. A minor modification to the formula used to relate conductivity data to phase volume fractions was found to improve agreement between the methods. GDT and EIT were then applied together to simultaneously measure the solid, liquid, and gas radial distributions within several vertical three-phase flows. For average solid volume fractions up to 0.30, the gas distribution for each gas flow rate was approximately independent of the amount of solids in the column. Measurements made with this EIT system demonstrate that EIT may be used successfully for noninvasive, quantitative measurements of dispersed multiphase flows.

Comparison of the microstructure and phase stability of as-cast, CAD/CAM and powder metallurgy manufactured Co-Cr dental alloys.

Science.gov (United States)

Li, Kai Chun; Prior, David J; Waddell, J Neil; Swain, Michael V

2015-12-01

The objective of this study was to identify the different microstructures produced by CC, PM and as-cast techniques for Co-Cr alloys and their phase stability following porcelain firings. Three bi-layer porcelain veneered Co-Cr specimens and one monolithic Co-Cr specimen of each alloy group [cast, powder metallurgy (PM), CAD/CAM (CC)] were manufactured and analyzed using electron backscatter diffraction (EBSD), energy dispersive spectrometry (EDS) and X-ray diffraction (XRD). Specimens were treated to incremental numbers of porcelain firings (control 0, 5, 15) with crystallographic data, grain size and chemical composition subsequently obtained and analyzed. EBSD datasets of the cast alloy indicated large grains >200 μm whereas PM and CC alloy consisted of mean arithmetic grain sizes of 29.6 μm and 19.2 μm respectively. XRD and EBSD results both indicated the highest increase in hcp content (>13vol%) for cast Co-Cr alloy after treatment with porcelain firing while PM and CC indicated .05) was observed in CC. EDS line scans indicated an increase in Cr content at the alloy surface after porcelain firing treatment for all three alloys. PM and CC produced alloy had superior fcc phase stability after porcelain firings compared to a traditional cast alloy. It is recommended that PM and CC alloys be used for porcelain-fused-to-metal restorations. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Effect of elevated pCO2 on metabolic responses of porcelain crab (Petrolisthes cinctipes) Larvae exposed to subsequent salinity stress.

Science.gov (United States)

Miller, Seth H; Zarate, Sonia; Smith, Edmund H; Gaylord, Brian; Hosfelt, Jessica D; Hill, Tessa M

2014-01-01

Future climate change is predicted to alter the physical characteristics of oceans and estuaries, including pH, temperature, oxygen, and salinity. Investigating how species react to the influence of such multiple stressors is crucial for assessing how future environmental change will alter marine ecosystems. The timing of multiple stressors can also be important, since in some cases stressors arise simultaneously, while in others they occur in rapid succession. In this study, we investigated the effects of elevated pCO2 on oxygen consumption by larvae of the intertidal porcelain crab Petrolisthes cinctipes when exposed to subsequent salinity stress. Such an exposure mimics how larvae under future acidified conditions will likely experience sudden runoff events such as those that occur seasonally along portions of the west coast of the U.S. and in other temperate systems, or how larvae encounter hypersaline waters when crossing density gradients via directed swimming. We raised larvae in the laboratory under ambient and predicted future pCO2 levels (385 and 1000 µatm) for 10 days, and then moved them to seawater at ambient pCO2 but with decreased, ambient, or elevated salinity, to monitor their respiration. While larvae raised under elevated pCO2 or exposed to stressful salinity conditions alone did not exhibit higher respiration rates than larvae held in ambient conditions, larvae exposed to elevated pCO2 followed by stressful salinity conditions consumed more oxygen. These results show that even when multiple stressors act sequentially rather than simultaneously, they can retain their capacity to detrimentally affect organisms.

Shade variance in ceramic restoration and shade tab: An in vitro study

Directory of Open Access Journals (Sweden)

Pannaikadu Somasundaram Prabu

2012-01-01

Full Text Available Background: In clinical practice aesthetics for any restoration needs to consider the parameters of surface form, translucency and colour.To achieve ideal aesthetics the colour replication process for dental porcelain is the most important step which comprises of a shade selection phase followed by shade duplication. Materials and Methods: The ceramic brands Vita VMK95 (classic and Ivoclar classic V were used for comparison with Vita classic shade tab guide shades A2 and B2. The samples were made of specific shape, size, and were of the recommended dimensions from investing self-cure acrylic strips to casted NiCr specimens Objective. The objective of this study was to quantify the results in CIE AE units system for the colour differences between the Vita shade guide colours and two commercial porcelains for metal ceramic crowns. Results: The results indicated that the porcelains do not match the shade guides to which they are compared and shade variations exist between different lots of porcelain from the same and different manufacturer. Conclusion: Problems identified that porcelains do not match the shade guides to which they are compared and shade variations exist between different lots of porcelain from the same and different manufacturer

Study on the provenance of ancient Yaozhou celadon made at Lidipo and Shangdian during Kin period using nuclear technology

International Nuclear Information System (INIS)

Wang, Y.Q.; Xue, D.X.

2007-01-01

Yaozhou Kiln at Lidipo and Shangdian are two independent porcelain kiln groups of Yaozhou kiln series in Shanxi Province. Both of them were consisted of some individual porcelain kilns. The samples of 20 pieces of porcelain sherds produced in Shangdian and 43 pieces of porcelain sherds made in Lidipo sites which produced in Kin Dynasty (1115-1234 A.D.) have been collected. The main chemical compositions in body were determined by X-ray fluorescence (XRF). The contents of trace elements were measured using neutron activation analysis (NAA). Principal component analysis (PCA) and stepwise discriminant analysis were used to study the provenance characteristic of these samples. The results indicated that the main components and trace elements in the specimen can be used to reveal the provenance characteristic. (author)

Influence of nepheline syenite and milling time on the rheological properties of a porcelain stoneware tile slip

Directory of Open Access Journals (Sweden)

Jazayeri, S. H.

2003-08-01

Full Text Available The rheological properties of porcelain stoneware tile slips were investigated using a rotational rheometer. The first step in the study was to evaluate the rheological behaviour of a reference slip at different particle size distributions to determine the optimum conditions at which to carry out the investigation of the influence of nepheline syenite in the mix. In the second step part of the K-feldspar in the reference mix was replaced with nepheline syenite such that the mix composition contained 10 % nepheline syenite. The flow curve, yield stress and thixotropy of the slips were evaluated at different milling times in order to study the effect of particle size on the rheological behaviour. The milling times for the reference mix and for the mix with nepheline syenite which resulted in the best rheological parameters were found.

Se han investigado las propiedades reológicas de barbotinas de porcelana dura para pavimentos usando un reómetro rotacional. El primer paso del estudio fue evaluar el comportamiento reológico de una barbotina de referencia con diferentes distribuciones de tamaño de partícula con el fin de determinar las condiciones óptimas bajo las cuales estudiar la influencia de nefelina sienita en la mezcla. En la segunda etapa, parte del feldespato potásico de la mezcla de referencia se substituyó por nefelina sienita de forma que la composición de la mezcla tuviera un 10% de neflina sienita. Se evaluaron las curvas de flujo, los puntos de fluidez y la tixotropía de las barbotinas tras diferentes tiempos de molienda con el fin de estudiar el efecto del tamaño de partícula en el comportamiento reológico. Se determinaron los tiempos de molienda en los que se alcanzaban los mejores parámetros reológicos para la mezcla de referencia y la de nefelina sienita.

Replacing a Missing Tooth

Science.gov (United States)

... lateral incisor. This may be accomplished by adding plastic or porcelain filling material or a porcelain crown ... This type of bridge requires much less tooth reduction of adjacent teeth, and there is no danger ...

Opaque Nuclear Strategy

Science.gov (United States)

2017-12-01

Relationship, 0000271219, 1961. https://www.cia.gov/ library / readingroom/docs/DOC_0000271219.pdf. . Trends in South Africa’s Nuclear Security Policies ...official policy or position of the Department of Defense or the U.S. Government. IRB number ____N/A____. 12a. DISTRIBUTION / AVAILABILITY STATEMENT...how Israel and South Africa shaped those strategies. This research may contribute to better understanding possible policies of potential nuclear

Effect of chemical composition and alumina content on structure and ...

Indian Academy of Sciences (India)

porcelain types (Morrell 1985; Vazquez and Mejia Velasquez. 1998). By increasing ... Orlova et al found that, in alumina porcelains, opti- mum mechanical ... of high mobility of ions, acceptable electrical performance may be achieved with ...

Numerical Modelling for the Thermal Performance Assessment of a Semi-Opaque Façade with a Multilayer of Nano-Structured and Phase Change Materials

Directory of Open Access Journals (Sweden)

Carla Balocco

2017-10-01

Full Text Available The aim of our present study was to assess and compare the thermo-physical and energy behaviour of different integrated building façades, using a multi-physics simulation approach. Advanced integrated façades composed of opaque modules, one of them with a phase change materials (PCM layer, the others with multilayer panels, combined with transparent ones, consisting of nano-structured materials and new-generation photovoltaic systems, were investigated. A multi-physics approach was used for the design optimization of the studied components and evaluation of their thermo-physical and heat transfer performance. In particular, computational fluid dynamics (CFD multi-physics transient simulations were performed to assess air temperature and velocity fields inside the ventilated cavities. Analysis of heat and mass exchange through all the components was assessed during heating and cooling mode of a reference building. The typical Mediterranean climate was considered. Results comparison allowed the dynamic heat transfer evaluation of the multilayer façades as a function of variable climatic conditions, and their flexibility and adaptability exploitation, when different energy strategies are pursued. The multi-physics modelling approach used, proved to be a strong tool for the energy design optimization and energy sustainability evaluation of different advance materials and building components.

[Corrosion property and oxide film of dental casting alloys before and after porcelain firing].

Science.gov (United States)

Ma, Qian; Wu, Feng-ming

2011-03-01

To evaluate the types and compositions of oxide films formed during porcelain-fused-to-metal (PFM) firing on three kinds of dental casting alloys, and to investigate the corrosion property of these alloys in Dulbecco's modification of Eagle's medium (DMEM) cell culture fluid, before and after PFM firing. Specimens of three dental casting alloys (Ni-Cr, Co-Cr and Ni-Ti) before and after PFM firing were prepared, and were immersed in DMEM cell culture fluid. After 30 days, the type and concentration of released metal ions were measured using inductively coupled plasma atomic emission spectroscopy (ICP-AES). X-ray photoelectron spectroscopy (XPS) and scanning electron microscope (SEM) were used for analysis of oxide film on the alloys. One way-ANOVA was adopted in data analysis. The total amount of metal ions released from the three dental alloys was found to be highest in Ni-Cr alloy [(2.829 ± 0.694) mg/L], followed by Co-Cr [(2.120 ± 0.418) mg/L] and Ni-Ti alloy [(1.211 ± 0.101) mg/L]. The amount of Ni ions released from Ni-Cr alloys [(1.531 ± 0.392) mg/L] was higher than that from Ni-Ti alloys [(0.830 ± 0.052) mg/L]. The amount of Cr, Mo ions released from Co-Cr alloy [Cr: (0.048 ± 0.011) mg/L, Mo: (1.562 ± 0.333) mg/L] was higher than that from Ni-Cr alloy [Cr: (0.034 ± 0.002) mg/L, Mo: (1.264 ± 0.302) mg/L] and Ni-Ti alloy [Cr: (0.013 ± 0.006) mg/L, Mo: (0.151 ± 0.026) mg/L] (P < 0.05). After PFM firing, the total amount of metal irons released from the three dental alloys decreased [Ni-Cr: (0.861 ± 0.054) mg/L, Co-Cr: (0.695 ± 0.327) mg/L, Ni-Ti: (0.892 ± 0.115) mg/L] (P < 0.05). In addition, XPS showed increase of Cr(2)O(3) and Mo-Ni oxide on the surface of all the alloys after PFM firing. The amount of ions released from Ni-Cr alloy was the highest among the three dental casting alloys, this means Ni-Cr alloy is prone to corrode. The PFM firing process changed the alloys' surface composition. Increased Ni, Cr and Mo were found in oxide film, and

Terror management theory applied clinically: implications for existential-integrative psychotherapy.

Science.gov (United States)

Lewis, Adam M

2014-01-01

Existential psychotherapy and Terror Management Theory (TMT) offer explanations for the potential psychological effects of death awareness, although their respective literatures bases differ in clarity, research, and implications for treating psychopathology. Existential therapy is often opaque to many therapists, in part due to the lack of consensus on what constitutes its practice, limited published practical examples, and few empirical studies examining its efficacy. By contrast, TMT has an extensive empirical literature base, both within social psychology and spanning multiple disciplines, although previously unexplored within clinical and counseling psychology. This article explores the implications of a proposed TMT integrated existential therapy (TIE), bridging the gap between disciplines in order to meet the needs of the aging population and current challenges facing existential therapists.

Four channel Cosmic Ray detector based on polymaq

Science.gov (United States)

Herrera-Guzman, K. N.; Gutierrez-Sanchez, R. A.; Felix, J.

2017-01-01

The Cherenkov radiation has been widely studied in transparent materials, and applied to detect and identify elementary particles. But it has not been widely studied in opaque materials. A four channels radiation detector has been designed, built, characterized, and operated; based on four polymaq (UHMW-PE) bars of 2.54 cm X 5.08 cm X 25.4 cm, which is an opaque material to visible radiation to the human eye. Silicon photo detectors, Hamamatsu, avalanche type (APD) are used to detect the radiation produced by the passage of particles in the detector blocks. The design, construction, characterization, operation, and preliminary results of this cosmic ray detector details are presented.

Bulletin of Materials Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

Titania doped triaxial porcelain: Enhancement of strength by controlled heat treatment. Sunipa Bhattacharyya Swapan Kumar Das Kausik Dana ... in their growth was ascertained through SEM analysis. The present heat treatment process may be useful to produce high strength porcelain body from a common triaxial system.

The ceramic SiO2 and SiO2-TiO2 coatings on biomedical Ti6Al4VELI titanium alloy

International Nuclear Information System (INIS)

Surowska, B.; Walczak, M.; Bienias, J.

2004-01-01

The paper presents the study of intermediate SiO 2 and SiO 2 -TiO 2 sol-gel coatings and dental porcelain coatings on Ti6Al4VELI titanium alloy. Surface microstructures and wear behaviour by pin-on-disc method of the ceramic coatings were investigated. The analysis revealed: (1) a compact, homogeneous SiO 2 and SiO 2 -TiO 2 coating and (2) that intermediate coatings may provide a durable joint between metal and porcelain, and (3) that dental porcelain on SiO 2 and TiO 2 coatings shows high wear resistance. (author)

Letters from China: A History of the Origins of the Chemical Analysis of Ceramics.

Science.gov (United States)

Pollard, A M

2015-02-01

This paper is an attempt to document the early history of the quantitative chemical analysis of ceramic materials in Europe, with a specific interest in the analysis of archaeological ceramics. This inevitably leads to a study of the attempts made in Europe to imitate the miraculous material--porcelain--imported from China from the fourteenth century onwards. It is clear that before the end of the eighteenth century progress was made in this endeavor by systematic but essentially trial-and-error firing of various raw materials, culminating in the successful production of European porcelain by Böttger and von Tschirnhaus in 1709. Shortly after this, letters describing the Chinese manufacture of porcelain, and, more importantly, samples of raw and fired material, began to arrive in Europe from French Jesuit missionaries, which were subjected to intense study. Following the perfection of gravimetric methods of chemical analysis in the late eighteenth century, these Chinese samples, and samples of porcelain from various European factories, were regularly analysed, particularly by Brongniart at Sèvres. Similar work was carried out on English porcelain by Simeon Shaw and Sir Arthur Church. The origins of the chemical analysis of archaeological ceramics are still somewhat obscure, but must date to the late eighteenth or early nineteenth centuries, by the likes of Vauquelin and Chaptal.

Study on the property of the production for Fengdongyan kiln in Early Ming dynasty by INAA and EDXRF

International Nuclear Information System (INIS)

Li, L.; Huang, Y.; Sun, H.Y.; Yan, L.T.; Feng, S.L.; Xu, Q.; Feng, X.Q.

2016-01-01

A lot of official wares carved “Guan” or the dragon patterns were excavated on the strata of Ming dynasty of the Fengdongyan kiln site at Dayao County. The imperial porcelain was fired in Hongwu and Yongle eras. However, the emergence of this imperial porcelain has triggered academic debate about the property of Fengdongyan kiln in the Early Ming dynasty. Based on the differences of the official kiln management, some scholars have determined that the property of the production for this kiln was the civilian kiln. According to the historical textural records and typology, others preliminary confirmed that Fengdongyan kiln was the official kiln. In this paper, the elemental compositions of body and glaze in imperial and civilian porcelain are study by INAA and EDXRF for determining the property of the production for this kiln in Early Ming dynasty. After the processing of experimental data by geochemical analysis and principal component analysis, the result show that the raw materials for making body and glaze in imperial porcelain are similar with those of the civilian porcelain and the degrees of elutriation for body can be slightly different in HW-M period of Ming dynasty. The analytical results support the view that the Fengdongyan kiln is civilian not official.

Study on the property of the production for Fengdongyan kiln in Early Ming dynasty by INAA and EDXRF

Energy Technology Data Exchange (ETDEWEB)

Li, L. [Institute of High Energy Physics, Chinese Academy of Sciences, 19 Yu Quan Lu, Beijing 100049 (China); Huang, Y.; Sun, H.Y. [Institute of High Energy Physics, Chinese Academy of Sciences, 19 Yu Quan Lu, Beijing 100049 (China); University of Chinese Academy of Sciences, Chinese Academy of Sciences, Beijing 100049 (China); Yan, L.T.; Feng, S.L.; Xu, Q. [Institute of High Energy Physics, Chinese Academy of Sciences, 19 Yu Quan Lu, Beijing 100049 (China); Feng, X.Q., E-mail: fengxq@ihep.ac.cn [Institute of High Energy Physics, Chinese Academy of Sciences, 19 Yu Quan Lu, Beijing 100049 (China)

2016-08-15

A lot of official wares carved “Guan” or the dragon patterns were excavated on the strata of Ming dynasty of the Fengdongyan kiln site at Dayao County. The imperial porcelain was fired in Hongwu and Yongle eras. However, the emergence of this imperial porcelain has triggered academic debate about the property of Fengdongyan kiln in the Early Ming dynasty. Based on the differences of the official kiln management, some scholars have determined that the property of the production for this kiln was the civilian kiln. According to the historical textural records and typology, others preliminary confirmed that Fengdongyan kiln was the official kiln. In this paper, the elemental compositions of body and glaze in imperial and civilian porcelain are study by INAA and EDXRF for determining the property of the production for this kiln in Early Ming dynasty. After the processing of experimental data by geochemical analysis and principal component analysis, the result show that the raw materials for making body and glaze in imperial porcelain are similar with those of the civilian porcelain and the degrees of elutriation for body can be slightly different in HW-M period of Ming dynasty. The analytical results support the view that the Fengdongyan kiln is civilian not official.

Provenience studies of the Ko-Kutani ware by neutron activation analysis

International Nuclear Information System (INIS)

Kawashima, Tatsuro.

1990-01-01

The instrumental neutron activation analysis has been applied to the multielemental analysis of eight samples of the Ko-Kutani ware including the Aote's that is one of semi-porcelain body. Each sample was compared with concentration of the useful index element, such as Ta, Sc, Ba, Hf, Th and rare earth, to discriminate the Arita group from the Kutani group. Eight samples were judged as products of the Arita, just as in previous paper. (author)

Measuring the diameter of rising gas bubbles by means of the ultrasound transit time technique

Energy Technology Data Exchange (ETDEWEB)

Richter, T., E-mail: Thomas.Richter6@tu-dresden.de; Eckert, K., E-mail: Kerstin.Eckert@tu-dresden.de; Yang, X.; Odenbach, S.

2015-09-15

Highlights: • Ultrasound transit time technique (UTTT) is applied to the zig-zag raise of gas bubble. • Comparison of bubble diameter and tilt, measured by UTTT, with high-speed imaging. • Uncertainty in the determination of the bubble diameter by UTTT is less than 7%. • UTTT is able to measure dynamic changes in bubble size in opaque liquids and vessels. • UTTT can be applied to liquid metal loops. - Abstract: This study presents ultrasound transit time technique (UTTT) measurements of the diameter variations of single argon bubbles rising in a zig-zag trajectory in water. Simultaneous size measurements with a high-speed camera show that UTTT resolves both the apparent diameter and the tilt of the bubble axis with an accuracy of better than 7%. This qualifies UTTT for the measurement of bubble sizes in opaque liquids, such as liquid metals, or vessels.

Real-time X-ray transmission microscopy for fundamental studies solidification: Al-Al2Au eutectic

International Nuclear Information System (INIS)

Curreri, Peter A.; Kaukler, William F.; Sen, Subhayu

1998-01-01

High resolution real-time X-ray Transmission Microscopy, XTM, has been applied to obtain information fundamental to solidification of optically opaque metallic systems. We have previously reported the measurement of the solute profile in the liquid, phase growth, and detailed solid-liquid interfacial morphology of aluminum based alloys with exposure times less than 2 seconds. Recent advances in XTM furnace design have provided an increase in real-time magnification (during solidification) for the XTM from 40X to 160X. The increased magnification has enabled for the first time the XTM imaging of real-time growth of fibers and particles with diameters of 5 μm. We have previously applied this system to study the kinetics of formation and morphological evolution of secondary fibers and particles in Al-Bi monotectic alloys. In this paper we present the preliminary results of the first real-time observations of fiber morphology evolution in optically opaque bulk metal sample of Aluminum-Gold eutectic alloy. These studies show that the XTM can be applied to study the fundamentals of eutectic and monotectic solidification. We are currently attempting to apply this technology in the fundamentals of solidification in microgravity

Use of supplementary lighting top screens and effects on greenhouse climate and return on investment

NARCIS (Netherlands)

Ooster, A. van 't; Henten, E.J. van; Janssen, E.G.O.N.; Bongaerts, E.

2008-01-01

Discomfort caused by light pollution from greenhouses that apply supplementary lighting is an issue in Dutch society nowadays. At this moment Dutch legislation requires an opaque screen that reduces light transmission of the greenhouse wall by 95%. In 2008 also the light transmission of the

Recycling Colonial Cultural Heritage

DEFF Research Database (Denmark)

Johansson, Troels Degn

2017-01-01

of the first consignment of South East Asian porcelain destined for the European market. San Jago’s cargo of porcelain was realized economically by a big auction in the Netherlands. According to the Museum and it’s installation, the “importance of this auction was unprecedented and it provided enormous...

Combustion Characteristics of Butane Porous Burner for Thermoelectric Power Generation

Directory of Open Access Journals (Sweden)

K. F. Mustafa

2015-01-01

Full Text Available The present study explores the utilization of a porous burner for thermoelectric power generation. The porous burner was tested with butane gas using two sets of configurations: single layer porcelain and a stacked-up double layer alumina and porcelain. Six PbSnTe thermoelectric (TE modules with a total area of 54 cm2 were attached to the wall of the burner. Fins were also added to the cold side of the TE modules. Fuel-air equivalence ratio was varied between the blowoff and flashback limit and the corresponding temperature, current-voltage, and emissions were recorded. The stacked-up double layer negatively affected the combustion efficiency at an equivalence ratio of 0.20 to 0.42, but single layer porcelain shows diminishing trend in the equivalence ratio of 0.60 to 0.90. The surface temperature of a stacked-up porous media is considerably higher than the single layer. Carbon monoxide emission is independent for both porous media configurations, but moderate reduction was recorded for single layer porcelain at lean fuel-air equivalence ratio. Nitrogen oxides is insensitive in the lean fuel-air equivalence ratio for both configurations, even though slight reduction was observed in the rich region for single layer porcelain. Power output was found to be highly dependent on the temperature gradient.

The Layout of Power and Space in Jingdezhen Imperial Factory

Directory of Open Access Journals (Sweden)

Zhan Jia

2014-12-01

Full Text Available This paper, by referring to the archaeological reports and local gazetteers and comparing images of porcelain wares, makes a comprehensive and in-depth analysis of the layout of power and space in Jingdezhen Imperial Factory according to its geography, geomancy, security management, space regulation, architectural features, production characteristics and production layout. It contends that the Imperial Factory which integrates porcelain making factory with local government is the embodiment of absolute monarchy in ceramic culture. The factory is located on Zhushan mountain, the center of Jingdezhen’s industry, business and transportation. Being at the center, it gives off an air of prestige and majesty, overlooking dominantly the surrounding private kilns. It has also turned the political system into power operation, setting up not only workshops but also administrative offices. By taking advantage of the best resources, it has produced porcelain for imperial family and court. Its specialized production has solved the contradiction between complicated technology and numerous procedures of production. The shape, color and pattern of the porcelain wares are strictly stipulated and the best of the best wares are demanded. Hence the porcelain production is featured with longest firing, largest scale, superb craftsmanship, and best kinds of wares. All of these reveal the process and rule power and space are intersected and different cultures overlapped.

Reliability and failure modes of implant-supported zirconium-oxide fixed dental prostheses related to veneering techniques

Science.gov (United States)

Baldassarri, Marta; Zhang, Yu; Thompson, Van P.; Rekow, Elizabeth D.; Stappert, Christian F. J.

2011-01-01

Summary Objectives To compare fatigue failure modes and reliability of hand-veneered and over-pressed implant-supported three-unit zirconium-oxide fixed-dental-prostheses(FDPs). Methods Sixty-four custom-made zirconium-oxide abutments (n=32/group) and thirty-two zirconium-oxide FDP-frameworks were CAD/CAM manufactured. Frameworks were veneered with hand-built up or over-pressed porcelain (n=16/group). Step-stress-accelerated-life-testing (SSALT) was performed in water applying a distributed contact load at the buccal cusp-pontic-area. Post failure examinations were carried out using optical (polarized-reflected-light) and scanning electron microscopy (SEM) to visualize crack propagation and failure modes. Reliability was compared using cumulative-damage step-stress analysis (Alta-7-Pro, Reliasoft). Results Crack propagation was observed in the veneering porcelain during fatigue. The majority of zirconium-oxide FDPs demonstrated porcelain chipping as the dominant failure mode. Nevertheless, fracture of the zirconium-oxide frameworks was also observed. Over-pressed FDPs failed earlier at a mean failure load of 696 ± 149 N relative to hand-veneered at 882 ± 61 N (profile I). Weibull-stress-number of cycles-unreliability-curves were generated. The reliability (2-sided at 90% confidence bounds) for a 400N load at 100K cycles indicated values of 0.84 (0.98-0.24) for the hand-veneered FDPs and 0.50 (0.82-0.09) for their over-pressed counterparts. Conclusions Both zirconium-oxide FDP systems were resistant under accelerated-life-time-testing. Over-pressed specimens were more susceptible to fatigue loading with earlier veneer chipping. PMID:21557985

Biofilm Formation on Different Materials Used in Oral Rehabilitation

OpenAIRE

Souza, Júlio C. M.; Mota, Raquel R. C.; Sordi, Mariane B.; Passoni, Bernardo B.; Benfatti, Cesar A. M.; Magini, Ricardo S.

2016-01-01

Abstract The aim of this study was to evaluate the density and the morphological aspects of biofilms adhered to different materials applied in oral rehabilitation supported by dental implants. Sixty samples were divided into four groups: feldspar-based porcelain, CoCr alloy, commercially pure titanium grade IV and yttria-stabilized zirconia. Human saliva was diluted into BHI supplemented with sucrose to grow biofilms for 24 or 48 h. After this period, biofilm was removed by 1% protease treatm...

Accurate photopyroelectric measurements of thermal diffusivity of (semi)liquids

NARCIS (Netherlands)

Dadarlat, D.; Neamtu, C.; Surducan, E.; Sahraoui, A.H.; Longuemart, S.; Bicanic, D.

2002-01-01

The back photopyroelectric (PPE) configuration, with opaque sample and thermally thick sample and sensor, was applied in order to obtain room temperature values of the thermal diffusivity of some (semi)liquid materials. The methodology is based on a sample's thickness scan, and not on a frequency

Study of provenance properties on ancient celadon of different kilns with NAA

International Nuclear Information System (INIS)

Feng Songlin; Fan Dongyu; Feng Xiangqian; Xu Qing; Cheng Lin; Lei Yong; Shen Yueming; Zhang Wenjiang; Zhua Zhenxi

2005-01-01

Provenance characteristic is an important scientific parameter to identify ancient porcelain wares unearthed from sites and graves. The porcelain samples of Si-Long-Kou Yue kiln of Zhejiang Province, Hong-Zhou kiln of Jiangxi Province and Yao-Zhou kiln of Shanxi Province have been analyzed with neutron activation analysis (NAA). The experimental data were studied with statistic methods. The results show that the chemical compositions of porcelain body samples for three kilns were different. The difference was able to be identified. The body materials of both Si-Long-Kou Yue kiln and Hong-Zhou kiln of Jiangxi were similar. The samples of Yao-Zhou kiln in north of China existed obvious difference. (authors)

Dual-scan technique for the customization of zirconia computer-aided design/computer-aided manufacturing frameworks.

Science.gov (United States)

Andreiuolo, Rafael Ferrone; Sabrosa, Carlos Eduardo; Dias, Katia Regina H Cervantes

2013-09-01

The use of bi-layered all-ceramic crowns has continuously grown since the introduction of computer-aided design/computer-aided manufacturing (CAD/CAM) zirconia cores. Unfortunately, despite the outstanding mechanical properties of zirconia, problems related to porcelain cracking or chipping remain. One of the reasons for this is that ceramic copings are usually milled to uniform thicknesses of 0.3-0.6 mm around the whole tooth preparation. This may not provide uniform thickness or appropriate support for the veneering porcelain. To prevent these problems, the dual-scan technique demonstrates an alternative that allows the restorative team to customize zirconia CAD/CAM frameworks with adequate porcelain thickness and support in a simple manner.

A well organized opaqueness

International Nuclear Information System (INIS)

Gouriou, A.; Poizat, F.; Salles, B.

2008-01-01

The author criticizes the role and operation of the ADEME (the French agency of the environment and energy management) in the French policy on wind energy tariffs. He describes the arrangement of mandatory purchase of wind energy by EDF, reports and comments a controversy between the ADEME and the French Commission of energy regulation (CRE) on the first 1500 MW. He briefly describes the launching of the ToTEM programme, evokes the influence and demands of the wind energy lobby, describes the content of the Olin decree. In fact, the author tends to think that the ADEME is acting in favour of wind energy project promoters

Secret Societies, Opaque Routes

DEFF Research Database (Denmark)

Garsten, Christina; Sörbom, Adrienne

This paper departs from an interest in the involvement of business leaders in the sphere of politics, in the broad sense. At a general level, we are seeing a proliferation of usages of non-market corporate strategies, such as testimony, lobbying, interlocking of positions and other means...... as political. What is the role of business in the WEF, and how do business corporations advance their interests through the WEF? Inspired by Stephen Barley's (2010) work on how corporations have systematically built an institutional field to exert greater influence on the US Federal government, we aim...... with participants and organizers. Theoretically we will employ an organizational perspective, using the concept of "partial organization" as introduced by Göran Ahrne and Nils Brunsson (2011). The results show that corporations find a strategically positioned amplifier for their non-market interests in the WEF...

Reciclagem secundária de rejeitos de porcelanas elétricas em estruturas de concreto: determinação do desempenho sob envelhecimento acelerado Secondary recycling of electrical insulator porcelain waste in Portland concrete structures: determination of the performance under accelerated aging

Directory of Open Access Journals (Sweden)

K. F. Portella

2006-09-01

Full Text Available O uso de entulhos, entre outros rejeitos industriais e domésticos, pela construção civil vem sendo prática comum em diversos países desenvolvidos, em razão tanto do aumento da quantidade de rejeitos e conseqüente esgotamento de espaços apropriados para seu destino final, quanto da constante e cada vez mais rigorosa fiscalização e punição pelos organismos ambientais competentes. Antecipando maneiras para solução desses problemas, propôs-se o estudo da reciclagem e imobilização de rejeitos de porcelanas elétricas em concreto, em substituição parcial aos agregados graúdos e miúdos naturais. A vantagem não foi total por causa do indício de reações expansivas que poderiam prejudicar determinadas aplicações. Assim, foi proposto o estudo das condições ideais de dosagem para mitigar os efeitos de tais reações pela presença de contaminantes destes rejeitos. Os resultados demonstraram a efetiva promoção de reações do tipo álcali-agregado, e que o uso de cimentos especiais poderá diminuir o efeito prejudicial dos subprodutos formados.The use of rubbish and other kinds of domestic and industrial wastes on civil construction has been a common practice in many developed countries, due either to the increase in the amount of waste and the resultant reduction of appropriate places to its final disposal, as well as to the severity and steadiness of environmental inspection organizations. In order to provide beforehand manners to solve or reduce these problems, study of recycling and co-disposal of waste from porcelain electrical insulators in concrete was proposed. Besides the occurrence of expansive reactions, which may be harmful to the stability of important structures, the overall results were encouraging. Some contaminants found in the three phases of porcelain contributed to the happening of alkali-aggregate reaction, which can easily inhibited by the using of special cements, such as a sulfur-resistant one.

Monetary Policy Delelgation and Transparency of Policy Targets: A Positive Analysis

Science.gov (United States)

2011-06-01

neoclassical time- inconsistency framework, monetary policy is modeled as a two-stage game between the private sector and the central bank as...simple neoclassical model and keep it to a minimum complexity which suffices to derive the results. The applied game-theoretic framework stands in the...accountability may imply that central banks choose lo be opaque. Applying the theory of bureau- cracy to the ECB. Forder (2002) argues that central banks

INFLUENCE OF SILANE HEAT TREATMENT ON THE TENSILE BOND STRENGTH BETWEEN EX-3 SYNTHETIC VENEERING PORCELAIN AND COMPOSITE RESIN USING FIVE DIFFERENT ACTIVATION TEMPERATURES

Directory of Open Access Journals (Sweden)

Spartak Yanakiev

2017-02-01

Full Text Available Purpose: The purpose of the present study is to assess the effect of five different silane activation temperatures and eight activation methods on the tensile bond strength between one veneering porcelain and one composite resin material. Material and methods: A total of 81 ceramic rods were made of EX-3 veneering ceramic (Kuraray Noritake Dental, Japan. Sintered ceramic bars were grinded with diamond disks to size 10x2x2mm ± 0,05mm. The front part of each bar was polished. After ultrasonic cleaning in distilled water, the specimens were divided into nine groups. Silane was activated with air at room temperature, 38º С, 50º С, 100º С, 120º С using a custom made blow drier. In a silicone mold, a composite resin Z250 (3М ESPE, St. Paul, USA was condensed toward the bond ceramic surface. A total of 81 specimens approximately 2,0 cm long were prepared for tensile bond testing. One way ANOVA, followed by Bonferroni and Games-Howell tests were used for statistical analysis. Results: The lowest tensile bond strength was observed in the control group (3,51MPa. Group 2 yielded the highest bond strength among all groups (19,54MPa. Silane heat treatment enhanced the bond strength for all treatment methods. Within the polished specimens, the highest bond strength was yielded with warm air at 120ºС (11,31MPa. Conclusion: The most effective method for bonding Z250 composite resin to EX-3 veneering ceramic includes HF etching, silane, and adhesive resin. The most effective heat treatment method for bonding is hot air at 120ºС.

Infrared Heaters

Science.gov (United States)

1979-01-01

The heating units shown in the accompanying photos are Panelbloc infrared heaters, energy savers which burn little fuel in relation to their effective heat output. Produced by Bettcher Manufacturing Corporation, Cleveland, Ohio, Panelblocs are applicable to industrial or other facilities which have ceilings more than 12 feet high, such as those pictured: at left the Bare Hills Tennis Club, Baltimore, Maryland and at right, CVA Lincoln- Mercury, Gaithersburg, Maryland. The heaters are mounted high above the floor and they radiate infrared energy downward. Panelblocs do not waste energy by warming the surrounding air. Instead, they beam invisible heat rays directly to objects which absorb the radiation- people, floors, machinery and other plant equipment. All these objects in turn re-radiate the energy to the air. A key element in the Panelbloc design is a coating applied to the aluminized steel outer surface of the heater. This coating must be corrosion resistant at high temperatures and it must have high "emissivity"-the ability of a surface to emit radiant energy. The Bettcher company formerly used a porcelain coating, but it caused a production problem. Bettcher did not have the capability to apply the material in its own plant, so the heaters had to be shipped out of state for porcelainizing, which entailed extra cost. Bettcher sought a coating which could meet the specifications yet be applied in its own facilities. The company asked The Knowledge Availability Systems Center, Pittsburgh, Pennsylvania, a NASA Industrial Applications Center (IAC), for a search of NASA's files

Experimental observation of silver and gold penetration into dental ceramic by means of a radiotracer technique

International Nuclear Information System (INIS)

Moya, F.; Payan, J.; Bernardini, J.; Moya, E.G.

1987-01-01

A radiotracer technique was used to study silver and gold diffusion into dental porcelain under experimental conditions close to the real conditions in prosthetic laboratories for porcelain bakes. It was clearly shown that these non-oxidizable elements were able to diffuse into the ceramic as well as oxidizable ones. The penetration depth varied widely according to the element. The ratio DAg/DAu was about 10(3) around 850 degrees C. In contrast to gold, the silver diffusion rate was high enough to allow silver, from the metallic alloy, to be present at the external ceramic surface after diffusion into the ceramic. Hence, the greening of dental porcelains baked on silver-rich alloys could be explained mainly by a solid-state diffusion mechanism

Applying thermal neutron radiography to non-destructive assays of dynamic systems

International Nuclear Information System (INIS)

Silvani, Maria I.; Almeida, Gevaldo L. de; Goncalves, Marcelo J.; Lopes, Ricardo T.

2008-01-01

Dynamic processes or systems frequently can not have their behavior directly analyzed due to safety reasons or because they require destructive assays, which can not be always afforded when high-cost equipment, devices and components are involved. Under these circumstances, some kind of non-destructive technique should be applied to preserve the safety of the personnel performing the assay, as well as the integrity of the piece being inspected. Thermal neutrons are specially suited as a tool for this purpose, thanks to their capability to pass through metallic materials, which could be utterly opaque to X-rays. This paper describes the accomplishments achieved at the Instituto de Engenharia Nuclear / CNEN, Brazil, aiming at the development of an Image Acquisition System capable to perform non-destructive assays using thermal neutrons. It is comprised of a thermal neutron source provided by the Argonauta research reactor, a converter-scintillating screen, and a CCD-based video camera optically coupled to the screen through a dark chamber equipped with a mirror. The developed system has been used to acquire 2D neutron radiographic images of static devices to reveal their inner structure, as well as movies of running systems and working devices to verify its functioning and soundness. Radiographic images of objects taken at different angles would be later on used as projections to retrieve - through a proper unfolding software - their 3D images expressed as attenuation coefficients for thermal neutrons. A quantitative performance of the system has been assessed through its Modulation Transfer Function - MTF. In order to determine this curve, unique collimators designed to simulate different spatial frequencies have been manufactured. Besides that, images of some objects have been acquired with the system being developed as well as using the conventional radiographic film, allowing thus a qualitative comparison between them. (author)

Archaeometrical studies at Bucharest Department of Applied Physics

International Nuclear Information System (INIS)

Constantinescu, B.; Catana, D.; Plostinaru, D.; Bugoi, Roxana

1997-01-01

A programme for systematic investigation of Byzantine copper and lead coins, ceramics and glass bracelets found in Romania using Proton Induced X-Ray Emission (PIXE), X-Ray Fluorescence (XRF) and Fast Neutron Activation Analysis (FNAA), has been started in cooperation with Bucharest Museum of Art and History. It is also included in the frame of the European COST G1 action 'Ion Beam Analysis in Art and Archaeology'. For in-air PIXE, we used a 3-4 MeV proton beam obtained from the 6.5 MeV Cyclotron nominal regime protons extracted through an air cooled 20 μm aluminium foil in air, striking the sample after 8-10 cm. X-rays were detected through reflection, using a horizontal Si(Li) detector of 4.3 mm diameter active area. XRF measurements were done with a spectrometer consisting of a 30 mCi 241 Am annular gamma-source attached to a support that defines the angle of the incident photons and collimates the fluorescent X-rays in their path to the Si(Li) detector. For FNAA, the deuterons accelerated up to 13 MeV, bombarded a thick (166.5 mg/cm 2 ) Be target placed at 20 angle against the incident beam (up to 20 μA), indirectly water-cooled. The absolute neutron intensity flux on free air, at a distance of 10 cm behind the Be target was 1.82 x 108 n/cm 2 ·μC, with a neutron average energy of 5.24 MeV at 0 circ . Using fast neutron beam, some light elements can be determined: Al, Mg, Na, Si, but also Ca, Ti, Fe, Zn, Cd, In, Sn, Sb, Ba, Pb. The aim of the programme is to identify and classify the coins, in relation to their origins and to identify colouring agents, bleaching, opaquing and fining agents in ancient glassy materials in relation to various developments in glass technology. In our case, colorants (Mn, Fe, Cu, Zn, Sn, Sb, Pb) and opaquing agents (Sn, Sb, Pb) were determined. Results and performances, especially for Fe, In, Er, As, Sn, Sb, Pb for coins and K, Ca, Ti, Mn, Cu, Zr, Sr, Rb, Ba, La, Nd for ceramics, are obtained. Recently, an investigation of silver

Joining Dental Ceramic Layers With Glass

Science.gov (United States)

Saied, MA; Lloyd, IK; Haller, WK; Lawn, BR

2011-01-01

Objective Test the hypothesis that glass-bonding of free-form veneer and core ceramic layers can produce robust interfaces, chemically durable and aesthetic in appearance and, above all, resistant to delamination. Methods Layers of independently produced porcelains (NobelRondo™ Press porcelain, Nobel BioCare AB and Sagkura Interaction porcelain, Elephant Dental) and matching alumina or zirconia core ceramics (Procera alumina, Nobel BioCare AB, BioZyram yttria stabilized tetragonal zirconia polycrystal, Cyrtina Dental) were joined with designed glasses, tailored to match thermal expansion coefficients of the components and free of toxic elements. Scanning electron microprobe analysis was used to characterize the chemistry of the joined interfaces, specifically to confirm interdiffusion of ions. Vickers indentations were used to drive controlled corner cracks into the glass interlayers to evaluate the toughness of the interfaces. Results The glass-bonded interfaces were found to have robust integrity relative to interfaces fused without glass, or those fused with a resin-based adhesive. Significance The structural integrity of the interfaces between porcelain veneers and alumina or zirconia cores is a critical factor in the longevity of all-ceramic dental crowns and fixed dental prostheses. PMID:21802131

A study on fabrication technology of ceramic overpack

International Nuclear Information System (INIS)

Teshima, T.; Ishikawa, H.; Sasaki, N.; Karita, Y.; Katsumoto, K.

1990-03-01

The conceptual design and fabrication test of a full-scale ceramic overpack were performed from the viewpoint of structural barriers as a part of program to evaluate their potential use as overpack under conditions of deep geological disposal. Materials investigated were porcelain (used for insulators) and Al 2 O 3 with high purity of 99.7 %. The selected design consisted of a cylindrical body with hemispherical heads at each end. The design thickness of overpack is the sum of the structural thickness and corrosion allowance. The thickness required to resist the lithostatic pressure was estimated by the basic cylinder buckling formulas and finite element stress analyses in both case of uniform and non-uniform external pressure conditions. These analyses showed that structural thickness of 119 mm was necessary for overpack of porcelain and 40 mm for Al 2 O 3 under the predicted maximum uniform pressure. In addition, fracture probability of delayed failure, one of significant degradation mode, was estimated for overpack of porcelain. A full-scale overpack of porcelain, of dimensions 800 mm outer diameter x 2200 mm length x 150 mm wall thickness, was fabricated under the ordinary level of fabrication technology. (author)

Wear characteristics of polished and glazed lithium disilicate ceramics opposed to three ceramic materials.

Science.gov (United States)

Saiki, Osamu; Koizumi, Hiroyasu; Akazawa, Nobutaka; Kodaira, Akihisa; Okamura, Kentaro; Matsumura, Hideo

2016-01-01

This study compared the wear characteristics of a heat-pressed lithium disilicate ceramic material opposed to feldspathic porcelain, a lithium disilicate glass ceramic, and zirconia materials. Ceramic plate specimens were prepared from feldspathic porcelain (EX-3 nA1B), lithium disilicate glass ceramics (e.max CAD MO1/C14), and zirconia (Katana KT 10) and then ground or polished. Rounded rod specimens were fabricated from heat-pressed lithium disilicate glass ceramic (e.max press LT A3) and then glazed or polished. A sliding wear testing apparatus was used for wear testing. Wear of glazed rods was greater than that of polished rods when they were abraded with ground zirconia, ground porcelain, polished porcelain, or polished lithium disilicate ceramics. For both glazed and polished rods, wear was greater when the rods were abraded with ground plates. The findings indicate that application of a polished surface rather than a glazed surface is recommended for single restorations made of heat-pressed lithium disilicate material. In addition, care must be taken when polishing opposing materials, especially those used in occlusal contact areas. (J Oral Sci 58, 117-123, 2016).

Development and characterisation of a new anti-slip glaze with smooth texture and easy-cleaning for porcelain stoneware; Desarrollo y caracterizacion de un nuevo esmalte antideslizante de textura lisa y de facil limpieza para baldosas de gres porcelanico

Energy Technology Data Exchange (ETDEWEB)

Barrachina Albert, E.; Martin Nunez, J. A.; Fraga Chiva, D.; Calvet Roures, I.; Cada Castello, J. B.

2016-05-01

Since conventional anti-slip enamels show some disadvantages, directly related to the surface roughness which prevents the adequate surface cleaning of tile, an anti-slip enamel exhibiting glass-ceramic nature has been designed, characterized by being stain-resistant and presenting a smooth texture and touch soft. To do this, new matte frits and raw materials with similar nature have been used, refractory enough to be suitable in enamel compositions for porcelain stoneware. The glass-ceramic glaze thus prepared was characterized by various instrumental techniques (X-ray fluorescence [XRF], scanning electron microscopy [SEM], X-ray diffraction [XRD], mechanical profilometry and microhardness measurements), in order to check the nature of crystallized phases, their morphology, surface roughness and microhardness of the finished tile. In addition, the quality of the glazed piece has been evaluated by the regulations of chemical resistance, stain-resistance and slipperiness. The enamel obtained has devitrified in crystals of silicoaluminates of calcium and barium and complies with standards of anti-slip and stain-resistence, as it has a surface roughness similar to a non-slip enamel. (Author)

Color related to ceramic and zirconia restorations: a review.

Science.gov (United States)

Vichi, Alessandro; Louca, Chris; Corciolani, Gabriele; Ferrari, Marco

2011-01-01

The requirement to achieve natural looking restorations is one of the most challenging aspects of dentistry, and the shade matching of dental restorations with the natural dentition is a difficult task due to the complex optical characteristics of natural teeth. Dental porcelain is considered the reference material for prosthetic rehabilitation, but it is not easy to handle and aesthetic excellence is quite difficult to obtain. For these reasons, shade matching with dental porcelain is often considered to be more artistic than scientific. Shade matching is considered unpredictable due to several variables that may influence the final appearance of a restoration. In order to improve this situation, over the last decade new shade guides and instruments have been developed and the aesthetic aspects of dental porcelain have been further investigated. In this review some aspects of color selection and color reproduction have been examined. Color selection has advanced through the development of new shade guides and electronic shade taking devices, although visual assessment has still not been entirely replaced by electronic instruments. Color reproduction with dental porcelain has improved thanks to advances in the performance and knowledge of dental porcelain, but is still not easy to achieve. The difficulties of achieving good aesthetics with PFM restorations and the desire for metal free solutions have resulted in the increased use of zirconia. The unique optical properties of zirconia have introduced new opportunities for achieving superior aesthetics, however further research is required with this material. Copyright © 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Polymerization of dual cure resin cements applied for luting tooth colored fiber posts

Directory of Open Access Journals (Sweden)

Ghavam M.

2007-05-01

Full Text Available Background and Aim: Insufficient polymerization of resin cements is of considerable clinical importance, because of mechanical deficiencies and biological side effects of uncured resin. Dual cure resin cements are getting popular in luting tooth colored posts and although their curing is claimed to proceed chemically, polymerization efficiency in deep areas of canal is uncertain. The aim of this study was to evaluate degree of polymerization of dual-cure resin cements used for luting translucent and opaque fiber posts in different distances from the light tip. Materials and Methods: In this experimental in vitro study, degree of conversion of two dual cured resin cements, Rely X ARC (3M, ESPE and Nexus 2 (Kerr, USA were measured when used with DT-Light and DT-White posts (RTD, France. The light curing unit used was Optilux 501, with output of 650-700 mw/cm2 with emitting time of 60 seconds. Degree of conversion was measured in three different depths (4, 6, 8 mm by FTIR. The data were analyzed using ANOVA and Post hoc tests. P0.05. Nexus used with DT-Light had lower DC% in 8 mm depth (P<0.05. Nexus used with DT-White showed lower DC% in 8 mm depth compared to 4 mm depth. The control groups of both cements showed significant increased DC% in 4 mm depth compared to 6 and 8 mm depths (P<0.05. DT-White caused decreased DC% in both cements in 4 mm. DT-Light caused increased DC% of Rely X in 6 mm depth compared to DT-White and control. DT-Light increased DC% of Nexus in 6 and 8 mm depths, compared to DT-White and control groups. Conclusion: Based on the results of this study, application of translucent fiber posts has a significant effect on degree of polymerization in dual-cure resin cements, compared to opaque types. Their better light transmission to deep areas due to the effect of optical fibers, can lead to better results.

Refractory porcelain enamel passive-thermal-control coating for high-temperature superalloys

Science.gov (United States)

Levin, H.; Auker, B. H.; Gardos, M. N.

1973-01-01

Study was conducted to match thermal expansion coefficients thereby preventing enamels from cracking. Report discusses various enamel coatings that are applied to two different high-temperature superalloys. Study may be of interest to manufacturers of chemical equipment, furnaces, and metal components intended for high-temperature applications.

Biofilm Formation on Different Materials Used in Oral Rehabilitation.

Science.gov (United States)

Souza, Júlio C M; Mota, Raquel R C; Sordi, Mariane B; Passoni, Bernardo B; Benfatti, Cesar A M; Magini, Ricardo S

2016-01-01

The aim of this study was to evaluate the density and the morphological aspects of biofilms adhered to different materials applied in oral rehabilitation supported by dental implants. Sixty samples were divided into four groups: feldspar-based porcelain, CoCr alloy, commercially pure titanium grade IV and yttria-stabilized zirconia. Human saliva was diluted into BHI supplemented with sucrose to grow biofilms for 24 or 48 h. After this period, biofilm was removed by 1% protease treatment and then analyzed by spectrophotometry (absorbance), colony forming unit method (CFU.cm-2) and field-emission guns scanning electron microscopy (FEG-SEM). The highest values of absorbance and CFU.cm-2 were recorded on biofilms grown on CoCr alloys when compared to the other test materials for 24 or 48 h. Also, FEG-SEM images showed a high biofilm density on CoCr. There were no significant differences in absorbance and CFU.cm-2 between biofilms grown on zirconia, porcelain and titanium (p<0.05). Microbiological assays associated with microscopic analyses detected a higher accumulation of oral biofilms on CoCr-based materials than that on titanium or zirconia that are used for prosthetic structures.

Comparison of the Candida albicans and biofilm formation amount on natural tooth,

Directory of Open Access Journals (Sweden)

Serdar Polat

2012-03-01

Full Text Available Objective: This study compared the retention of the Candidaalbicans and biofilm formation on natural teeth, porcelainand acrylic resin.Materials and methods: Samples are taken with thesterile ecuvion sticks from the buccal embrasures of thenatural tooth, porcelain and acrylic. The biofilm productionof candida reproducing strains was determined withmicroplate method. Samples are settled in 0.5 ml sterilephosphate buffered saline. Reproduction detected coloniesdefined to species in accordance with their macroscopicand microscopic features and germ tube test inmicrobiology laboratory.Results: There was significant differences for retention ofCandida albicans and biofilm formation on the surface oftooth, porcelain and acrylic (p<0.05.Conclusion: Adherence of Candida albicans and biofilmformation on the porcelain significantly less than naturaltooth and acrylic, and retention and biofilm formation onthe tooth less than acrylic.

Time dependent view factor methods

International Nuclear Information System (INIS)

Kirkpatrick, R.C.

1998-03-01

View factors have been used for treating radiation transport between opaque surfaces bounding a transparent medium for several decades. However, in recent years they have been applied to problems involving intense bursts of radiation in enclosed volumes such as in the laser fusion hohlraums. In these problems, several aspects require treatment of time dependence

Eco-efficient concretes: the effects of using recycled ceramic material from sanitary installations on the mechanical properties of concrete.

Science.gov (United States)

Guerra, I; Vivar, I; Llamas, B; Juan, A; Moran, J

2009-02-01

The aim of this research was to investigate some of the physical and mechanical properties of concrete mixed under laboratory conditions, where different proportions of coarse aggregate materials were substituted by porcelain from sanitary installations. The results of the tests show that the concrete produced has the same mechanical characteristics as conventional concrete, thus opening a door to selective recycling of sanitary porcelain and its use in the production of concrete.