WorldWideScience

Sample records for on-line solid-phase extraction

  1. Flow injection on-line solid phase extraction for ultra-trace lead screening with hydride generation atomic fluorescence spectrometry.

    Science.gov (United States)

    Wan, Zhuo; Xu, Zhangrun; Wang, Jianhua

    2006-01-01

    A flow injection (FI) on-line solid phase extraction (SPE) procedure for ultra-trace lead separation and preconcentration was developed, followed by hydride generation and atomic fluorescence spectrometric (AFS) detection. Lead is retained on an iminodiacetate chelating resin packed microcolumn, and is afterward eluted with 2.5% (v/v) hydrochloric acid to facilitate the hydride generation by reaction with alkaline tetrahydroborate solution with 1% (m/v) potassium ferricyanide as an oxidizing (or sensitizing) reagent. The hydride was separated from the reaction medium in the gas-liquid separator and swept into the atomizer for quantification. The chemical variables and the FI flow parameters were carefully optimized. With a sample loading volume of 4.8 ml, quantitative retention of lead was obtained, along with an enrichment factor of 11.3 and a sampling frequency of 50 h(-1). A detection limit of 4 ng l(-1), defined as 3 times the blank standard deviation (3 sigma), was achieved along with a RSD value of 1.6% at the 0.4 microg l(-1) level. The procedure was validated by determining lead contents in two certified reference materials, and its practical applicability was further demonstrated by analysing a variety of biological and environmental samples.

  2. Data correlation in on-line solid-phase extraction-gas chromatography-atomic emission/mass spectrometric detection of unknown microcontaminants

    NARCIS (Netherlands)

    Hankemeier, Th.; Rozenbrand, J.; Abhadur, M.; Vreuls, J.J.; Brinkman, U.A.Th.

    1998-01-01

    A procedure is described for the (non-target) screening of hetero-atom-containing compounds in tap and waste water by correlating data obtained by gas chromatography (GC) using atomic emission (AED) and mass selective (MS) detection. Solid-phase extraction (SPE) was coupled on-line to both GC system

  3. An On-Line Solid Phase Extraction-Liquid Chromatography-Tandem Mass Spectrometry Method for the Determination of Perfluoroalkyl Acids in Drinking and Surface Waters

    Directory of Open Access Journals (Sweden)

    Michela Mazzoni

    2015-01-01

    Full Text Available An UHPLC-MS/MS multiresidue method based on an on-line solid phase extraction (SPE procedure was developed for the simultaneous determination of 9 perfluorinated carboxylates (from 4 to 12 carbon atoms and 3 perfluorinated sulphonates (from 4 to 8 carbon atoms. This work proposes using an on-line solid phase extraction before chromatographic separation and analysis to replace traditional methods of off-line SPE before direct injection to LC-MS/MS. Manual sample preparation was reduced to sample centrifugation and acidification, thus eliminating several procedural errors and significantly reducing time-consuming and costs. Ionization suppression between target perfluorinated analytes and their coeluting SIL-IS were detected for homologues with a number of carbon atoms less than 9, but the quantitation was not affected. Total matrix effect corrected by SIL-IS, inclusive of extraction efficacy, and of ionization efficiency, ranged between −34 and +39%. The percentage of recoveries, between 76 and 134%, calculated in different matrices (tap water and rivers impacted by different pollutions was generally satisfactory. LODs and LOQs of this on-line SPE method, which also incorporate recovery losses, ranged from 0.2 to 5.0 ng/L and from 1 to 20 ng/L, respectively. Validated on-line SPE-LC/MS/MS method has been applied in a wide survey for the determination of perfluoroalkyl acids in Italian surface and ground waters.

  4. The determination of organochlorine pesticides based on dynamic microwave-assisted extraction coupled with on-line solid-phase extraction of high-performance liquid chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Chen Ligang [College of Chemistry, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Ding Lan [College of Chemistry, Jilin University, 2699 Qianjin Street, Changchun 130012 (China)]. E-mail: analchem@jlu.edu.cn; Jin Haiyan [College of Chemistry, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Song Daqian [College of Chemistry, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Zhang Huarong [College of Chemistry, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Li Jiantao [College of Chemistry, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Zhang Kun [College of Chemistry, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Wang Yutang [College of Chemistry, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Zhang Hanqi [College of Chemistry, Jilin University, 2699 Qianjin Street, Changchun 130012 (China)

    2007-04-25

    A rapid technique based on dynamic microwave-assisted extraction coupled with on-line solid-phase extraction of high-performance liquid chromatography (DMAE-SPE-HPLC) has been developed. A TM{sub 010} microwave resonance cavity built in the laboratory was applied to concentrate the microwave energy. The sample placed in the zone of microwave irradiation was extracted with 95% acetonitrile (ACN) aqueous solution which was driven by a peristaltic pump at a flow rate of 1.0 mL min{sup -1}. The extraction can be completed in a recirculating system in 10 min. When a number of extraction cycles were completed, the extract (1 mL) was diluted on-line with water. Then the extract was loaded into an SPE column where the analytes were retained while the unretained matrix components were washed away. Subsequently, the analytes were automatically transferred from the SPE column to the analytical column and determined by UV detector at 238 nm. The technique was used for determination of organochlorine pesticides (OCPs) in grains, including wheat, rice, corn and bean. The limits of detection of OCPs are in the range of 19-37 ng g{sup -1}. The recoveries obtained by analyzing the four spiked grain samples are in the range of 86-105%, whereas the relative standard deviation (R.S.D.) values are <8.7% ranging from 1.2 to 8.7%. Our method was demonstrated to be fast, accurate, and precise. In addition, only small quantities of solvent and sample were required.

  5. On-line anion exchange solid-phase extraction coupled to liquid chromatography with fluorescence detection to determine quinolones in water and human urine.

    Science.gov (United States)

    Lara, Francisco J; Del Olmo-Iruela, Monsalud; García-Campaña, Ana M

    2013-10-04

    An analytical method based on on-line solid-phase extraction coupled to liquid chromatography with fluorescence detection has been developed to determine quinolones in tap water and human urine. A home-made setup was used to percolate 10 mL of sample through a solid-phase extraction column. Analytes were retained onto the sorbent by an anion exchange mechanism which ensures an optimum compatibility with the subsequent chromatographic separation. A C-18 column containing core-shell particles (2.6 μm) was used to achieve peak efficiencies up to 200,000 plates/m, at a flow rate of 1.2 mL/min and without the need for special pumps. The method allowed the determination of 11 quinolones directly in tap water samples in less than 20 min and with limits of detection ranging between 7 and 110 ng/L. The sensitivity achieved made possible the direct determination of 9 quinolones in human urine without any sample treatment, just dilution with water. Relative recoveries between 94 and 109% were obtained meaning that the matrix effect in human urine is negligible after dilution. Satisfactory results were also obtained in terms of precision since relative standard deviations were always below 13%.

  6. On-line immunoaffinity solid-phase extraction capillary electrophoresis mass spectrometry for the analysis of large biomolecules: a preliminary report.

    Science.gov (United States)

    Medina-Casanellas, Silvia; Benavente, Fernando; Giménez, Estela; Barbosa, José; Sanz-Nebot, Victoria

    2014-08-01

    The analysis of large biomolecules by on-line immunoaffinity solid-phase extraction capillary electrophoresis mass spectrometry (IA-SPE-CE-MS) remains unexplored because of the complex issues that need to be addressed. In this preliminary study, we used the human glycoprotein transferrin (Tf) as a model of a large biomolecule. First, we established by CE-UV a novel method compatible with IA-SPE-CE-MS, based on the use of a fused silica capillary coated with an anionic derivative of polyacrylamide (UltraTrol(TM) Dynamic Pre-Coat High Normal, HN) to prevent protein adsorption. The methodology allowed the detection of the most abundant Tf sialoforms. Repeatability studies demonstrated high stability of the coated capillaries, which was required for on-line immunoextraction and MS detection. IA-SPE-CE-UV and IA-SPE-CE-MS methods were optimized for the analysis of Tf standards and human serum samples using a laboratory-made IA sorbent. Three peaks corresponding to Tf were detected with UV detection when on-line immunoextraction was applied to the standards. The use of MS detection, however, reduced the resolution of the electrophoretic separation. Finally, we demonstrated that it was possible to detect Tf in human serum samples, after off-line serum sample de-salting by centrifugal filtration.

  7. [Determination of estrogen residues in drinking water by on-line solid phase extraction based on sol-gel technique coupled with high performance liquid chromatography].

    Science.gov (United States)

    Li, Longfei; Su, Min; Shi, Xiaolei; Wang, Yana; Wang, Minmin; He, Jinxing

    2014-02-01

    A method for the determination of diethylstilbestrol (DES), hexestrol (HEX) and dienestrol (DS) residues in drinking water was established by on-line solid phase extraction (SPE) coupled with high performance liquid chromatography (HPLC). The material synthesized on the base of sol-gel technology was employed as adsorbent. This material was prepared using 3-aminopropyltriethoxysilane (APTES) as the functional monomer, tetraethoxysilane (TEOS) as the crosslinking agent, and acetic acid as the initiator. The synthesized adsorbent showed outstanding property for the estrogen extraction. The estrogen can be caught effectively from water samples and the extraction can be achieved rapidly. Some important parameters, such as pH of sample solution, eluent solvents, loading flow rate, which might influence extraction efficiency, were optimized. The results indicated that the limit of detection (S/N = 3) of the developed method could reach 0.07-0.13 microg/L under the conditions of pH 7.0 of sample solution, methanol and 1% (v/v) acetic acid aqueous solution as the eluent solvent and the loading flow rate of 2 mL/min. The recoveries of the three estrogens from the water samples at three spiked levels ranged from 82.31% to 99.43% with RSD of 1.61%-7.15%. The method was simple, rapid, and suitable to detect the trace residues of estrogens in drinking water.

  8. [Determination of 28 organochlorine and pyrethroid pesticides in pine nuts using solid-phase extraction and on-line gel permeation chromatography-gas chromatography/mass spectrometry].

    Science.gov (United States)

    Kang, Qinghe; Wu, Yan; Gao, Kaiyang; Li, Zhibin

    2009-03-01

    An analytical method has been developed for the determination of 28 organochlorine pesticides and pyrethroid pesticides in pine nuts. The sample was extracted With acetonitrile-water (4:1, v/v) as the extraction solution by means of high-speed homogenization. The crude extract was purified by an Aluminium-N solid phase extraction column to remove most of the fat and sterols in the sample, then on-line gel permeation chromatography-gas chromatography/ mass spectrometry (GPC-GC/MS) analysis was performed. The recoveries for the most of pesticides in the sample spiked with the standards of 0.05 mg/kg were 70%-120%, and the relative standard deviations were less than 15%. The limits of detection of 28 organochlorine pesti- and pyrethroid pesticides were 0.002-0.05 mg/kg. The linear relationship and the recovery results were satisfactory. The method is rapid, accurate, highly senstive, and can be used for the simultaneous determination of pesticide residues in pine nuts.

  9. Determination of arachidonic acid by on-line solid-phase extraction HPLC with UV detection for screening of cytosolic phospholipase A2α inhibitors.

    Science.gov (United States)

    Hanekamp, Walburga; Lehr, Matthias

    2012-07-01

    An on-line solid-phase extraction (SPE)-liquid chromatographic method with ultraviolet detection at 200nm for screening of inhibitors of cytosolic phospholipase A(2)α (cPLA(2)α) was developed and validated. cPLA(2)α was isolated from porcine platelets. Enzyme activity was determined by measuring the release of arachidonic acid from a phospholipid substrate using automated on-line sample clean up on a trap column followed by isocratic back-flush elution on a RP18 analytical column. While the use of a conventional RP18 column for trapping the analyte led to peak broadening only after a few runs due to pollution of the column by binding of components present in the enzyme preparation, the application of a turbulent flow column (TurboFlow Cyclone™) resulted in sharp peaks even after a plurality of injections. Interestingly, for sample introduction a turbulent flow of the mobile phase produced by high flow rates was not necessary to maintain good peak shapes. The same result could also be achieved applying low flow rates (0.5 mL/min). Several known cPLA(2)α inhibitors were used to validate the test system.

  10. On-line solid phase extraction using ion-pair microparticles combined with ICP-OES for the simultaneous preconcentration and determination of uranium and thorium

    Energy Technology Data Exchange (ETDEWEB)

    Yousefi, Seyed Reza; Zolfonoun, Ehsan [Nuclear Science and Technology Research Institute, Tehran (Iran, Islamic Republic of). NFCRS

    2016-07-01

    In this work, after on-line and in-situ solid phase extraction technique was used for the extraction and preconcentration of uranium and thorium from aqueous samples prior to inductively coupled plasma optical emission spectrometry (ICP-OES) determination. In this method, sodium hexafluorophosphate (as an ion-pairing agent) was added to the sample solution containing the cationic surfactant (dodecyltrimethylammonium bromide) and the complexing agent (dibenzoylmethane). A cloudy solution was formed as a result of formation of an ion pair between surfactant and hexafluorophosphate. The solid microparticles were passed through a microcolumn filter and the adsorbed microparticles were subsequently eluted with acid, which was directly introduced into the ICP-OES nebulizer. The main variables affecting the pre-concentration and determination steps of uranium and thorium were studied and optimized. Under the optimum conditions, the enhancement factors of 97 and 95 and the detection limits of 0.52 and 0.21 μg L{sup -1} were obtained for uranium and thorium, respectively.

  11. Ultraviolet vapor generation atomic fluorescence spectrometric determination of mercury in natural water with enrichment by on-line solid phase extraction

    Science.gov (United States)

    Qin, Deyuan; Gao, Feng; Zhang, Zhaohui; Zhao, Liqian; Liu, Jixin; Ye, Jianping; Li, Junwei; Zheng, Fengxi

    2013-10-01

    A novel method, which coupled an on-line solid phase extraction (SPE) enrichment with ultraviolet vapor generation (UVG) atomic fluorescence spectrometry (AFS), was developed to improve the sensitivity of mercury determination and to remove the interference of some anion and organics to UVG of mercury. A high mercury retention efficiency and maximum exclusion of inorganic and organic matrix in water samples were achieved by using C18 SPE mini cartridge modified with sodium diethyldithiocarbamate (DDTC). Fast and efficient elution from the cartridge was found by using L-cysteine mixing solution. Furthermore, through the investigation of different UV reactor designs, the most important factor was the structure of the reactor (which corresponded roughly to the photon flux) wherein the tubing was sintered into the UV lamp to give the highest UV generation efficiency. The second factor was the materials of the tubing (which roughly corresponded to the working wavelength). Synthetic quartz, characterized by the highest transparency at 185 nm, attained the highest UVG efficiency, suggesting that the most favorable wavelength for UVG was 185 nm. Under optimum conditions, the achievable detection limit (3σ) with sample loadings of 10.0 mL was 0.03 ng L- 1 and 0.08 ng L- 1 with different manifolds, respectively. The method was successfully applied to the determination of Hg in tap water, river water and lake water samples.

  12. Automated determination of total captopril in urine by liquid chromatography with post-column derivatization coupled to on-line solid phase extraction in a sequential injection manifold.

    Science.gov (United States)

    Karakosta, Theano D; Tzanavaras, Paraskevas D; Themelis, Demetrius G

    2012-01-15

    The present study reports a new liquid chromatographic (HPLC) method for the determination of the anti-hypertension drug captopril (CAP) in human urine. After its separation from the sample matrix in a reversed phase HPLC column, CAP reacts with the thiol-selective reagent ethyl-propiolate (EP) in a post-column configuration and the formed thioacrylate derivative is detected at 285 nm. Automated 4-fold preconcentration of the analyte prior to analysis was achieved by an on-line solid phase extraction (SPE) step using a sequential injection (SI) manifold. The Oasis HLB SPE cartridges offered quantitative recoveries and effective sample cleaning by applying a simple SPE protocol. The limits of detection and quantitation were 10 μg L(-1) and 35 μg L(-1) respectively. The percent recoveries for the analysis of human urine samples ranged between 90 and 96% and 95 and 104% using aqueous and matrix matched calibration curves respectively. Copyright © 2011 Elsevier B.V. All rights reserved.

  13. On-line monitoring of the photocatalytic degradation of 2,4-D and dicamba using a solid-phase extraction-multisyringe flow injection system.

    Science.gov (United States)

    Chávez-Moreno, Carmín; Ferrer, Laura; Hinojosa-Reyes, Laura; Hernández-Ramírez, Aracely; Cerdà, Víctor; Guzmán-Mar, Jorge

    2013-11-15

    A fully automated on-line system for monitoring the photocatalytic degradation of herbicides was developed using multisyringe flow injection analysis (MSFIA) coupled to a solid phase extraction (SPE) unit with UV detection. The calibration curves were linear in the concentration range of 100-1000 μg L(-1) for 3,6-dichloro-2-methoxybenzoic acid (dicamba) and 500-3000 μg L(-1) for 2,4-dichlorophenoxyacetic acid (2,4-D), while the detection limits were 30 and 135 μg L(-1) for dicamba and 2,4-D, respectively. The monitoring of the photocatalytic degradation (TiO2 anatase/UV 254 nm) of these two herbicides was performed by MSFIA-SPE system using a small sample volume (2 mL) in a fully automated approach. The degradation was assessed in ultrapure and drinking water with initial concentrations of 1000 and 2000 μg L(-1) for dicamba and 2,4-D, respectively. Degradation percentages of approximately 85% were obtained for both herbicides in ultrapure water after 45 min of photocatalytic treatment. A similar degradation efficiency in drinking water was observed for 2,4-D, whereas dicamba exhibited a lower degradation percentage (75%), which could be attributed to the presence of inorganic species in this kind of water. Copyright © 2013 Elsevier Ltd. All rights reserved.

  14. Interfacing on-line solid phase extraction with monolithic column multisyringe chromatography and chemiluminescence detection: An effective tool for fast, sensitive and selective determination of thiazide diuretics.

    Science.gov (United States)

    Maya, Fernando; Estela, José Manuel; Cerdà, Víctor

    2010-01-15

    A new, multisyringe flow injection set-up has been developed for the completely automated determination of trace thiazide compounds with diuretic action in different types of samples. The proposed instrumental set-up exploits for the first time, a low pressure on-line solid phase extraction-liquid chromatography-chemiluminescence detection method. This novel combination of sample treatments in flow systems expands the current applicability of low pressure liquid chromatography due to the isolation/preconcentration of the target compounds, besides high selectivity and sensitivity. For the determination of three thiazide compounds named hydroflumethiazide, furosemide and bendroflumethiazide, the proposed set-up provided with the preconcentration of only 1mL of sample, limits of detection of 3, 60 and 40microgL(-1), respectively. Furthermore wide linear dynamic ranges of 6-4000, 140-20,000 and 90-40,000microgL(-1), respectively, were obtained. Besides of this, a high injection throughput of 12h(-1) was also achieved. As in sports, thiazide diuretics are prohibited substances, the proposed method has been applied to their determination in urine samples. Furthermore the potential of the proposed method as a fast-screening approach for emerging contaminants in waters has been also tested by applying it to well water and leachates from a solid waste landfill.

  15. Determination of biocides and pesticides by on-line solid phase extraction coupled with mass spectrometry and their behaviour in wastewater and surface water

    Energy Technology Data Exchange (ETDEWEB)

    Singer, Heinz; Jaus, Sylvia; Hanke, Irene; Lueck, Alfred; Hollender, Juliane [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Ueberlandstrasse 133, CH-8600 Duebendorf (Switzerland); Alder, Alfredo C., E-mail: alfredo.alder@eawag.c [Eawag, Swiss Federal Institute of Aquatic Science and Technology, Ueberlandstrasse 133, CH-8600 Duebendorf (Switzerland)

    2010-10-15

    This study focused on the input of hydrophilic biocides into the aquatic environment and on the efficiency of their removal in conventional wastewater treatment by a mass flux analysis. A fully automated method consisting of on-line solid phase extraction coupled to LC-ESI-MS/MS was developed and validated for the simultaneous trace determination of different biocidal compounds (1,2-benzisothiazoline-3-one (BIT), 3-Iodo-2-propynylbutyl-carbamate (IPBC), irgarol 1051 and 2-N-octyl-4-isothiazolinone (octhilinone, OIT), carbendazim, diazinon, diuron, isoproturon, mecoprop, terbutryn and terbutylazine) and pharmaceuticals (diclofenac and sulfamethoxazole) in wastewater and surface water. In the tertiary effluent, the highest average concentrations were determined for mecoprop (1010 ng/L) which was at comparable levels as the pharmaceuticals diclofenac (690 ng/L) and sulfamethoxazole (140 ng/L) but 1-2 orders of magnitude higher than the other biocidal compounds. Average eliminations for all compounds were usually below 50%. During rain events, increased residual amounts of biocidal contaminants are discharged to receiving surface waters. - Incomplete removal of biocides and pesticides during wastewater treatment.

  16. On-line coupling of solid-phase extraction with mass spectrometry for the analysis of biological samples III. Determination of prednisolone in serum

    NARCIS (Netherlands)

    van Hout, M.W.J.; Hofland, C.M; Niederlander, H.A G; Bruins, A.P.; de Zeeuw, R.A.; de Jong, G.J.

    2003-01-01

    Solid-phase extraction (SPE) was directly coupled to mass spectrometry (MS) to assess the feasibility of the system for the rapid determination of prednisolone in serum. A C-18 stationary phase allowed washing of the cartridge with 25% methanol. Elution was performed by switching the methanol

  17. On-line coupling of solid-phase extraction with mass spectrometry for the analysis of biological samples III. Determination of prednisolone in serum

    NARCIS (Netherlands)

    van Hout, MWJ; Hofland, CM; Niederlander, HAG; Bruins, AP; de Zeeuw, RA; de Jong, GJ

    2003-01-01

    Solid-phase extraction (SPE) was directly coupled to mass spectrometry (MS) to assess the feasibility of the system for the rapid determination of prednisolone in serum. A C-18 stationary phase allowed washing of the cartridge with 25% methanol. Elution was performed by switching the methanol percen

  18. On-line preconcentration and determination of tetracycline residues in milk using solid-phase extraction in conjunction with flow injection spectrophotometry

    Directory of Open Access Journals (Sweden)

    Prinya Masawat

    2008-07-01

    Full Text Available A simple, cheap and highly sensitive system with on-line preconcentration using solid-phase extraction in conjunction with flow injection spectrophotometry for the determination of tetracycline residues in milk samples is described. C18 was used as packing material in a designed minicolumn used for preconcentration of tetracyclines. Tetracycline standard or sample solutions were dissolved in a mixed buffer solution of pH 4.0 containing boric acid, citric acid and sodium phosphate, then loaded to the minicolumn for 6 min followed by elution with a solution containing methanol : mixed buffer solution (40:60 by volume of pH 6.5 The absorbance of the eluate was measured at 370 nm. The calibration graph was linear in the range of 0.20-1.00, 0.20-4.00, and 0.20-1.00 mg L-1 for tetracycline (TC, oxytetracycline (OTC, and chlortetracycline (CTC respectively. The limits of detection were 0.08, 0.10, and 0.09mg L-1 for TC, OTC, and CTC respectively. Relative standard deviations for 20 replicated determinations of 0.20, 0.40, and 0.60 mg L-1 of TC were 7.03, 7.23, and 6.55 % respectively. Per cent recoveries for four commercial types of milk: U.H.T., pasteurised, raw, and sterilised milk were in the range of 86–109 (TC, 90–109 (OTC, and 89–108 (CTC. The sample throughput was 6 h-1.

  19. Preparation and evaluation of open tubular C18-silica monolithic microcartridges for preconcentration of peptides by on-line solid phase extraction capillary electrophoresis.

    Science.gov (United States)

    Ortiz-Villanueva, Elena; Benavente, Fernando; Giménez, Estela; Yilmaz, Fatma; Sanz-Nebot, Victoria

    2014-10-10

    In this study, C18-silica monoliths were synthesized as a porous layer in open tubular capillary columns, to be cut later into microcartridges for the analysis of neuropeptides by on-line solid-phase extraction capillary electrophoresis with UV and MS detection (SPE-CE-UV and SPE-CE-MS). First, several types of C18-silica monolithic (MtC18) microcartridges were used to analyse standard solutions of five neuropeptides (i.e. dynorphin A (1-7), substance P (7-11), endomorphin 1, methionine enkephalin and [Ala]-methionine enkephalin). The MtC18 sorbents were especially selective against endomorphin 1 and substance P (7-11)). The best results in terms of sensitivity and inter-microcartridge reproducibility were achieved with the microcartridges obtained from a 10-cm open tubular capillary column with a thin monolithic coating with large through-pores (1-5μm). Run-to-run repeatability, microcartridge durability, linearity ranges and LODs were studied by MtC18-SPE-CE-MS. As expected due to their greater selectivity, the best LOD enhancement was obtained for End1 and SP (7-11) (50 times with regard to CE-MS). Finally, the suitability of the methodology for analysing biological fluids was tested with plasma samples spiked with End1 and SP (7-11). Results obtained were promising because both neuropeptides could be detected at 0.05μgmL(-1), which was almost the same concentration level as for the standard solutions (0.01μgmL(-1)).

  20. Occurrence of the herbicide glyphosate and its metabolite AMPA in surface waters in Switzerland determined with on-line solid phase extraction LC-MS/MS.

    Science.gov (United States)

    Poiger, Thomas; Buerge, Ignaz J; Bächli, Astrid; Müller, Markus D; Balmer, Marianne E

    2017-01-01

    Glyphosate is currently one of the most important herbicides worldwide. Its unique properties provide for a wide range of uses in agriculture but also in non-agricultural areas. At the same time, its zwitterionic nature prevents the inclusion in multi-residue analytical methods for environmental monitoring. Consequently, despite its extensive use, data on occurrence of glyphosate in the aquatic environment is still scarce. Based on existing methods, we developed a simplified procedure for the determination of glyphosate and its main metabolite aminomethylphosphonic acid (AMPA) in water samples using derivatization with fluorenylmethyl chloroformate FMOC-Cl, combined with on-line solid phase extraction and liquid chromatography-tandem mass spectrometry (LC-MS/MS) detection. This method was extensively tested on over 1000 samples of surface water, groundwater, and treated wastewater and proved to be simple, sensitive, and reliable. Limits of quantification of 0.005 μg/L were routinely achieved. Glyphosate and AMPA were detected in the vast majority of stream water samples in the area of Zurich, Switzerland, with median concentrations of 0.11 and 0.20 μg/L and 95th percentile concentrations of 2.1 and 2.6 μg/L, respectively. Stream water data and data from treated wastewater indicated that non-agricultural uses may significantly contribute to the overall loads of glyphosate and AMPA in surface waters. In the investigated groundwater samples, selected specifically because they had shown presence of other herbicides in previous monitoring programs, glyphosate and AMPA were generally not detected, except for two monitoring sites in Karst aquifers, indicating that these compounds show much less tendency for leaching.

  1. Determination of As(III) and total inorganic As in water samples using an on-line solid phase extraction and flow injection hydride generation atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Sigrist, Mirna, E-mail: msigrist@fiq.unl.edu.ar [Laboratorio Central, Facultad de Ingenieria Quimica, Universidad Nacional del Litoral, Santiago del Estero 2654-Piso 6, (3000) Santa Fe (Argentina); Albertengo, Antonela; Beldomenico, Horacio [Laboratorio Central, Facultad de Ingenieria Quimica, Universidad Nacional del Litoral, Santiago del Estero 2654-Piso 6, (3000) Santa Fe (Argentina); Tudino, Mabel [Laboratorio de Analisis de Trazas, Departamento de Quimica Inorganica, Analitica y Quimica Fisica/INQUIMAE, Facultad de Ciencias Exactas y Naturales, Pabellon II, Ciudad Universitaria (1428), Buenos Aires (Argentina)

    2011-04-15

    A simple and robust on-line sequential injection system based on solid phase extraction (SPE) coupled to a flow injection hydride generation atomic absorption spectrometer (FI-HGAAS) with a heated quartz tube atomizer (QTA) was developed and optimized for the determination of As(III) in groundwater without any kind of sample pretreatment. The method was based on the selective retention of inorganic As(V) that was carried out by passing the filtered original sample through a cartridge containing a chloride-form strong anion exchanger. Thus the most toxic form, inorganic As(III), was determined fast and directly by AsH{sub 3} generation using 3.5 mol L{sup -1} HCl as carrier solution and 0.35% (m/v) NaBH{sub 4} in 0.025% NaOH as the reductant. Since the uptake of As(V) should be interfered by several anions of natural occurrence in waters, the effect of Cl{sup -}, SO{sub 4}{sup 2-}, NO{sub 3}{sup -}, HPO{sub 4}{sup 2-}, HCO{sub 3}{sup -} on retention was evaluated and discussed. The total soluble inorganic arsenic concentration was determined on aliquots of filtered samples acidified with concentrated HCl and pre-reduced with 5% KI-5% C{sub 6}H{sub 8}O{sub 6} solution. The concentration of As(V) was calculated by difference between the total soluble inorganic arsenic and As(III) concentrations. Detection limits (LODs) of 0.5 {mu}g L{sup -1} and 0.6 {mu}g L{sup -1} for As(III) and inorganic total As, respectively, were obtained for a 500 {mu}L sample volume. The obtained limits of detection allowed testing the water quality according to the national and international regulations. The analytical recovery for water samples spiked with As(III) ranged between 98% and 106%. The sampling throughput for As(III) determination was 60 samples h{sup -1}. The device for groundwater sampling was especially designed for the authors. Metallic components were avoided and the contact between the sample and the atmospheric oxygen was carried to a minimum. On-field arsenic species

  2. Accelerated solvent extraction followed by on-line solid-phase extraction coupled to ion trap LC/MS/MS for analysis of benzalkonium chlorides in sediment samples

    Science.gov (United States)

    Ferrer, I.; Furlong, E.T.

    2002-01-01

    Benzalkonium chlorides (BACs) were successfully extracted from sediment samples using a new methodology based on accelerated solvent extraction (ASE) followed by an on-line cleanup step. The BACs were detected by liquid chromatography/ion trap mass spectrometry (LC/MS) or tandem mass spectrometry (MS/MS) using an electrospray interface operated in the positive ion mode. This methodology combines the high efficiency of extraction provided by a pressurized fluid and the high sensitivity offered by the ion trap MS/MS. The effects of solvent type and ASE operational variables, such as temperature and pressure, were evaluated. After optimization, a mixture of acetonitrile/water (6:4 or 7:3) was found to be most efficient for extracting BACs from the sediment samples. Extraction recoveries ranged from 95 to 105% for C12 and C14 homologues, respectively. Total method recoveries from fortified sediment samples, using a cleanup step followed by ASE, were 85% for C12BAC and 79% for C14-BAC. The methodology developed in this work provides detection limits in the subnanogram per gram range. Concentrations of BAC homologues ranged from 22 to 206 ??g/kg in sediment samples from different river sites downstream from wastewater treatment plants. The high affinity of BACs for soil suggests that BACs preferentially concentrate in sediment rather than in water.

  3. Generic on-line solid phase extraction sample preparation strategies for the analysis of drugs in biological matrices by LC-MS/MS.

    Science.gov (United States)

    Bourgogne, Emmanuel; Grivet, Chantal; Varesio, Emmanuel; Hopfgartner, Gérard

    2015-01-01

    In the present work we investigate the integration of a single hardware platform (Prospekt-2) allowing on-line SPE with pre-/post-trapping dilution and direct injection of plasma extracts, and also compare the benefits and challenges of the different approaches for pharmaceutical drugs with heterogeneous physicochemical properties. In the first part, the generic use of on-line SPE with direct plasma injection or after protein precipitation was investigated for the quantitative analysis of talinolol. In the second part, pre-trapping and post-trapping dilution for on-line SPE is discussed for generic method development on an oxadiazole and its major metabolite. Finally, the difference of performance between direct plasma injection vs. off-line liquid-liquid extraction is also described for the quantification of buprenorphine and naltrexone down to 50 and 100 pg/ml using a 0.25 ml plasma aliquot. All assays were in human plasma and detection was performed by mass spectrometry detection either on simple or triple stage quadrupoles. Regardless of the tested strategy, assays were found linear, with precision and accuracy with <15% for all quality controls samples and <20% for lower limit of quantitation.

  4. Multiplexed Colorimetric Solid-Phase Extraction

    Science.gov (United States)

    Gazda, Daniel B.; Fritz, James S.; Porter, Marc D.

    2009-01-01

    Multiplexed colorimetric solid-phase extraction (MC-SPE) is an extension of colorimetric solid-phase extraction (C-SPE) an analytical platform that combines colorimetric reagents, solid phase extraction, and diffuse reflectance spectroscopy to quantify trace analytes in water. In CSPE, analytes are extracted and complexed on the surface of an extraction membrane impregnated with a colorimetric reagent. The analytes are then quantified directly on the membrane surface using a handheld diffuse reflectance spectrophotometer. Importantly, the use of solid-phase extraction membranes as the matrix for impregnation of the colorimetric reagents creates a concentration factor that enables the detection of low concentrations of analytes in small sample volumes. In extending C-SPE to a multiplexed format, a filter holder that incorporates discrete analysis channels and a jig that facilitates the concurrent operation of multiple sample syringes have been designed, enabling the simultaneous determination of multiple analytes. Separate, single analyte membranes, placed in a readout cartridge create unique, analyte-specific addresses at the exit of each channel. Following sample exposure, the diffuse reflectance spectrum of each address is collected serially and the Kubelka-Munk function is used to quantify each water quality parameter via calibration curves. In a demonstration, MC-SPE was used to measure the pH of a sample and quantitate Ag(I) and Ni(II).

  5. Simultaneous speciation of inorganic arsenic and antimony in water samples by hydride generation-double channel atomic fluorescence spectrometry with on-line solid-phase extraction using single-walled carbon nanotubes micro-column

    Energy Technology Data Exchange (ETDEWEB)

    Wu Hong, E-mail: wuhong1968@hotmail.com; Wang Xuecui; Liu Bing; Liu Yueling; Li Shanshan; Lu Jusheng; Tian Jiuying; Zhao Wenfeng; Yang Zonghui

    2011-01-15

    A new method was developed for the simultaneous speciation of inorganic arsenic and antimony in water by on-line solid-phase extraction coupled with hydride generation-double channel atomic fluorescence spectrometry (HG-DC-AFS). The speciation scheme involved the on-line formation and retention of the ammonium pyrrolidine dithiocarbamate complexes of As(III) and Sb(III) on a single-walled carbon nanotubes packed micro-column, followed by on-line elution and simultaneous detection of As(III) and Sb(III) by HG-DC-AFS; the total As and total Sb were determined by the same protocol after As(V) and Sb(V) were reduced by thiourea, with As(V) and Sb(V) concentrations obtained by subtraction. Various experimental parameters affecting the on-line solid-phase extraction and determination of the analytes species have been investigated in detail. With 180 s preconcentration time, the enrichment factors were found to be 25.4 for As(III) and 24.6 for Sb(III), with the limits of detection (LODs) of 3.8 ng L{sup -1} for As(III) and 2.1 ng L{sup -1} for Sb(III). The precisions (RSD) for five replicate measurements of 0.5 {mu}g L{sup -1} of As(III) and 0.2 {mu}g L{sup -1} of Sb(III) were 4.2 and 4.8%, respectively. The developed method was validated by the analysis of standard reference materials (NIST SRM 1640a), and was applied to the speciation of inorganic As and Sb in natural water samples.

  6. [Determination of five avermectins in bovine liver by on-line solid-phase extraction with hydrophobic monolithic column coupled with high performance liquid chromatography-tandem mass spectrometry].

    Science.gov (United States)

    Li, Xin; Zhang, Yaoqin; Ai, Lianfeng; Wang, Xuesheng; Wang, Manman; Xu, Houjun; Hao, Yulan

    2015-06-01

    A method based on on-line solid-phase extraction (SPE) with hydrophobic monolithic column coupled with high performance liquid chromatography-tandem mass spectrometry was developed for the simultaneous determination of five avermectins in bovine liver. A poly(butyl methacrylate-co-ethylene dimethacrylate) monolithic column was used as the sorbent. The parameters influenced on on-line SPE and separation process such as the loading mobile phase, the eluting flow rate and the solvent for the separation were investigated in detail. Blank samples, spiked samples, matrix effect and recovery experiments were investigated to evaluate the extraction efficiency and potential interfering compounds originating from the matrix. Under the optimized conditions, the method showed a linear range of 1-100 µg/L and the quantification limit of 5 µg/kg for each analyte. The presented method gave recoveries of 77.4%-98.4%. The relative standard deviations of intra-day and inter-day were 4.46%-8.03% and 4.79%-8.68%, respectively. Moreover, no significant changes were found in the extraction performance after more than 400 usages on one monolithic column, and even on the monoliths with various batches. The feasibility of the developed poly (butyl methacrylate-coethylene dimethacrylate) monolithic column based on the on-line SPE method for the determination of avermectins was further demonstrated by the analysis of real samples.

  7. On-line Ultrasound-Assisted Dispersive Micro-Solid-Phase Extraction Based on Amino Bimodal Mesoporous Silica Nanoparticles for the Preconcentration and Determination of Cadmium in Human Biological Samples.

    Science.gov (United States)

    Shirkhanloo, H; Falahnejad, M; Zavvar Mousavi, H

    2016-06-01

    On-line ultrasound-assisted dispersive micro-solid-phase extraction (USA-DμSPE) has been developed for preconcentration and separation of trace amounts of Cd(II) ions in 0.5 mL of human biological samples. In a syringe with a nylon membrane, new synthetic bulky amino bimodal mesoporous silica nanoparticles (NH2-UVM7) were dispersed as a nanoadsorbent in 5 mL of diluted serum sample (1:10), and after ultrasonic shaking, the liquid phase was separated from the solid phase. At the optimized pH, the chemical and physical adsorption of cadmium ions occurred, respectively, based on complexation with amine groups of UVM7 (Cd:NH2-UVM7) and silica nanoparticles. The analyte was then back-extracted from the sorbent with nitric acid solution (0.2 M), and its concentration was determined by electrothermal atomic absorption spectrometry (ETAAS). Under the optimized conditions, the linear range, limit of detection (LOD), and preconcentration factor (PF) were obtained as 0.01-0.56 μg L(-1), 0.002 μg L(-1), and 25, respectively. The adsorption capacity of NH2-UVM7 was found to be 108.6 mg g(-1) of cadmium. The validation of the methodology was performed by the human standard reference material (HSRM).

  8. Evaluation of the effect of TM208 on the activity of five cytochrome P450 enzymes using on-line solid-phase extraction HPLC-DAD: a cocktail approach.

    Science.gov (United States)

    Lin, Wensi; Zhang, Jianmei; Ling, Xiaomei; Yu, Ning; Li, Jing; Yang, Haisong; Li, Runtao; Cui, Jingrong

    2013-04-01

    A rapid, simple, and sensitive on-line solid-phase extraction HPLC-DAD method for simultaneous evaluation of the activity of five CYP450 isoforms (CYP1A2, CYP2C19, CYP2D6, CYP2E1 and CYP3A4) in vivo has been developed and validated. The five specific probe substrates include caffeine (1A2), metoprolol (2D6), dapsone (3A4), omeprazole (2C19) and chlorzoxazone (2E1). Automated pre-purification of plasma and enrichment of analytes were performed using a C18 on-line solid-phase extraction cartridge. After being eluted from the cartridge, the analytes and the internal standard antipyrine were separated on a C18 RP analytical column and analyzed by DAD. The method was validated to quantify the concentration ranges of 0.05-50.0 μg/ml for dapsone and omeprazole, 0.1-50.0 μg/ml for caffeine and 0.2-50.0 μg/ml for metoprolol and chlorzoxazone. The linearity (R(2)) for all analytes tested was exceeded 0.99. The intra-day precision ranged from 0.29 to 13% and the inter-day precision ranged from 5.0 to 15%, respectively. The intra-day and inter-day accuracy were between 86.7% and 113.6%. The extraction recoveries were in the range 82.8-109.9% for all the analytes and internal standard antipyrine. This method was successfully applied to evaluate the effects of TM208 on rat five CYP450 isoforms.

  9. On-line solid phase extraction using the Prospekt-2 coupled with a liquid chromatography/tandem mass spectrometer for the determination of dextromethorphan, dextrorphan and guaifenesin in human plasma.

    Science.gov (United States)

    Kuhlenbeck, Debbie L; Eichold, Thomas H; Hoke, Steven H; Baker, Timothy R; Mensen, Robert; Wehmeyer, Kenneth R

    2005-01-01

    An on-line liquid chromatography/tandem mass spectrometry (LC-MS/MS) procedure, using the Prospekt- 2 system, was developed and used for the determination of the levels of the active ingredients of cough/cold medications in human plasma matrix. The experimental configuration allows direct plasma injection by performing on- line solid phase extraction (SPE) on small cartridge columns prior to elution of the analyte(s) onto the analytical column and subsequent MS/MS detection. The quantitative analysis of three analytes with differing polarities, dextromethorphan (DEX), dextrorphan (DET) and guaifenesin (GG) in human plasma presented a significant challenge. Using stable-isotope-labeled internal standards for each analyte, the Prospekt-2 on-line methodology was evaluated for sensitivity, suppression, accuracy, precision, linearity, analyst time, analysis time, cost, carryover and ease of use. The lower limit of quantitation for the on-line SPE procedure for DEX, DET and GG was 0.05, 0.05 and 5.0 ng mL(-1), respectively, using a 0.1 mL sample volume. The linear range for DEX and DET was 0.05-50 ng mL(-1) and was 5-5,000 ng mL(-1) for GG. Accuracy and precision data for five different levels of QC samples were collected over three separate days. Accuracy ranged from 90% to 112% for all three analytes, while the precision, as measured by the %RSD, ranged from 1.5% to 16.0%

  10. Elimination of diastereomer interference to determine Telcagepant (MK-0974) in human plasma using on-line turbulent-flow technology and off-line solid-phase extraction coupled with liquid chromatography/tandem mass spectrometry.

    Science.gov (United States)

    Xu, Yang; Willson, Kenneth J; Anderson, Melanie D G; Musson, Donald G; Miller-Stein, Cynthia M; Woolf, Eric J

    2009-06-01

    To eliminate the diastereomer interference on Telcagepant (MK-0974) determination during clinical study support, on-line high turbulent-flow liquid chromatography (HTLC) methods, HTLC-A and HTLC-B that covered dynamic range of 0.5-500 nM and 5-5000 nM, respectively, were developed. To meet the requirement of rapid assay transfer among multiple laboratories and analysts, a solid-phase extraction (SPE) assay was derived from the existing HTLC-B assay under the same dynamic range. The on-line HTLC assays were achieved through direct injection of plasma samples, extraction of analyte with a Cohesive C18 column (50 mm x 0.5 mm, 50 microm), followed by HPLC separation on a FluoPhase RP column (100 mm x 2.1 mm, 5 microm) and MS/MS detection. The off-line SPE assay used Waters Oasis HLB microElution plate to extract the analytes from plasma matrix before injecting on a FluoPhase RP column (150 mm x 2.1 mm, 5 microm) for LC-MS/MS analysis. Under both on-line and off-line assay conditions, the diastereomer 1c was chromatographically separated from MK-0974. Cross-validation with the pooled samples demonstrated that both on-line and off-line assays provided comparable data with a difference of pros and cons of on-line and off-line assays with regard to man power involved in sample preparation, total analysis time, carryover, cost efficiency, and the requirement for assay transfer are discussed.

  11. Automatic On-line Solid-phase Extraction-Electrothermal Atomic Absorption Spectrometry Exploiting Sequential Injection Analysis for Trace Vanadium, Cadmium and Lead Determination in Human Urine Samples.

    Science.gov (United States)

    Giakisikli, Georgia; Ayala Quezada, Alejandro; Tanaka, Junpei; Anthemidis, Aristidis N; Murakami, Hiroya; Teshima, Norio; Sakai, Tadao

    2015-01-01

    A fully automated sequential injection column preconcentration method for the on-line determination of trace vanadium, cadmium and lead in urine samples was successfully developed, utilizing electrothermal atomic absorption spectrometry (ETAAS). Polyamino-polycarboxylic acid chelating resin (Nobias chelate PA-1) packed into a handmade minicolumn was used as a sorbent material. Effective on-line retention of chelate complexes of analytes was achieved at pH 6.0, while the highest elution effectiveness was observed with 1.0 mol L(-1) HNO3 in the reverse phase. Several analytical parameters, like the sample acidity, concentration and volume of the eluent as well as the loading/elution flow rates, have been studied, regarding the efficiency of the method, providing appropriate conditions for the analysis of real samples. For a 4.5 mL sample volume, the sampling frequency was 27 h(-1). The detection limits were found to be 3.0, 0.06 and 2.0 ng L(-1) for V(V), Cd(II) and Pb(II), respectively, with the relative standard deviations ranging between 1.9 - 3.7%. The accuracy of the proposed method was evaluated by analyzing a certified reference material (Seronorm(TM) trace elements urine) and spiked urine samples.

  12. On-line solid phase extraction-gas chromatography-cryotrapping-infrared spectrometry for the trace-level determination of microcontaminants in aqueous samples

    NARCIS (Netherlands)

    Hankemeier, T; Hooijschuur, E.; Vreuls, R.J.J.; Brinkman, U.A.Th.; Visser, T.

    1998-01-01

    A large-volume on-column GC-cryotrapping-IR system was developed for injections of up to 100 μl of organic extracts. Considerable reduction of the solvent-and-water background and enhanced analyte detectability was achieved by using an open-split interface between the GC column and the IR detector a

  13. On-line solid phase extraction-gas chromatography-cryotrapping-infrared spectrometry for the trace-level determination of microcontaminants in aqueous samples

    NARCIS (Netherlands)

    Hankemeier, T; Hooijschuur, E.; Vreuls, R.J.J.; Brinkman, U.A.Th.; Visser, T.

    1998-01-01

    A large-volume on-column GC-cryotrapping-IR system was developed for injections of up to 100 μl of organic extracts. Considerable reduction of the solvent-and-water background and enhanced analyte detectability was achieved by using an open-split interface between the GC column and the IR detector

  14. On-line restricted access molecularly imprinted solid phase extraction of ivermectin in meat samples followed by HPLC-UV analysis.

    Science.gov (United States)

    de Lima, Marcela Marília; Vieira, André Coutinho; Martins, Isarita; Boralli, Vanessa Bergamin; Borges, Keyller Bastos; Figueiredo, Eduardo Costa

    2016-04-15

    A new restricted access molecularly imprinted polymer coated with bovine serum albumin (RAMIP-BSA) was synthesized, characterized and used for direct analysis of ivermectin from bovine meat samples, in a two-dimensional liquid chromatography system with UV detection. Ivermectin, 4-vynilpiridine and ethylene glycol dimethacrylate were employed as template, functional monomer and cross-linker, respectively. A BSA layer was cross-linked around the polymer, resulting in a biocompatible chemical barrier able to eliminate about 100% of protein from the samples. Ivermectin was extracted from the minced meat samples through a solvent extraction using methanol:water (70:30, v:v), and the extracts were directly injected into the two-dimensional liquid chromatography system, without any other treatment. Samples, fortified with ivermectin from 50 to 500 μg kg(-1), were used to build the analytical calibration curve (r=0.996). The limit of quantification was 50 μg kg(-1). Precision and accuracy presented variation coefficients, as well as relative errors lower than 17.0% and within -18.5% and 22.0%, respectively.

  15. Simultaneous determination of caffeine, theophylline and theobromine in human plasma by on-line solid-phase extraction coupled to reversed-phase chromatography.

    Science.gov (United States)

    Emara, Samy

    2004-10-01

    A reversed-phase liquid chromatographic column switching system was described for the determination of caffeine (CF), theophylline (TH) and theobromine (TB) in human plasma with a direct injection procedure. A short protein-coated mu Bondapak CN silica pre-column (20 x 3 mm, i.d.) was used for enrichment of the drugs and clean up from weakly retained plasma components using phosphate buffer saline pH 7.4. After washing step, the retained drugs were flushed into a reversed-phase column (5 microm TSK gel ODS-80 TM, 150 x 4.6 mm i.d.) with a mobile phase of methanol-0.01 M phosphate buffer, pH 3.5 (30:70, v/v) for the final separation. The eluent was monitored with a UV detector at 275 nm. The resulting chromatograms showed no interference from endogenous plasma components. A linear relationship between the concentration of drug and peak height was confirmed in the range of 0.5-20 microg/mL for all drugs. High extraction recoveries from plasma ranging from 96.12 to 100.32% were achieved. Validation of the method was examined performing intra- and inter-day accuracy and precision and was found to be satisfactory. The coefficients of variation of the three drugs were less than 3% for intra-day and less than 4% for inter-day run assays.

  16. On-line coupling of solid-phase extraction with mass spectrometry for the analysis of biological samples. II. Determination of clenbuterol in urine using multiple-stage mass spectrometry in an ion-trap mass spectrometer

    NARCIS (Netherlands)

    van Hout, MWJ; Hofland, CM; Niederlander, HAG; de Jong, GJ

    2000-01-01

    Solid-phase extraction (SPE) was coupled to ion-trap mass spectrometry to determine clenbuterol in urine. For SPE a cartridge exchanger was used and, after extraction, the eluate was directly introduced into the mass spectrometer, For two types of cartridges, i.e. C-18 and polydivinylbenzene (PDVB),

  17. Determination of bezafibrate, methotrexate, cyclophosphamide, orlistat and enalapril in waste and surface waters using on-line solid-phase extraction liquid chromatography coupled to polarity-switching electrospray tandem mass spectrometry.

    Science.gov (United States)

    Garcia-Ac, Araceli; Segura, Pedro A; Gagnon, Christian; Sauvé, Sébastien

    2009-04-01

    We developed a rapid method for the monitoring of five selected pharmaceuticals in the influent and effluent of municipal wastewater treatment plants (WWTP) as well as in the effluent-receiving waters. To that end, we optimized and validated an analytical method based on on-line solid-phase extraction (on-line SPE) coupled with reversed-phase liquid chromatography-switching polarity electrospray ionization-tandem mass spectrometry (LC-ESI(+/-)-MS/MS). The target analytes have a variable hydrophobic character and belong to various therapeutic classes including the lipid regulator bezafibrate, the chemotherapy drugs methotrexate and cyclophosphamide, the lipase inhibitor orlistat and the angiotensin converting enzyme (ACE) inhibitor used in the treatment of hypertension, enalapril. The method combines positive and negative voltage switching modes, therefore all analytes can be determined using a single injection and without any reduction in sensitivity. In order to detect traces of these compounds, a preconcentration step before detection is performed by loading 1.00 mL of sample in an on-line SPE cartridge and eluting from the cartridge using a reversed-phase liquid chromatography gradient. Analysis of wastewater and surface water samples was greatly affected by co-eluting matrix compounds, to compensate for matrix effects quantitation was therefore performed using standard additions. Method intra-day precision was less than 6.5% and limits of detection in fortified matrix effluent samples ranged from 9 to 20 ng L(-1). Four of the target pharmaceuticals were detected in the WWTP effluents, enalapril and bezafibrate being the most abundant compounds with concentrations of 35 and 239 ng L(-1), respectively. Concentrations of these same compounds in surface water samples from sites downstream in the St. Lawrence River were 8 and 63 ng L(-1), respectively, which was mainly due to dilution.

  18. Synthesis and application of multi-walled carbon nanotubes-molecularly imprinted sol-gel composite material for on-line solid-phase extraction and high-performance liquid chromatography determination of trace Sudan IV

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Zhaohui, E-mail: zhaohuizhang77@hotmail.com [College of Chemistry and Chemical Engineering, Jishou University, Jishou 416000 (China); State Key Laboratory of Chemo/Biosensing and Chemometrics, Hunan University, Changsha 410082 (China); Zhang Huabin; Hu Yufang [College of Chemistry and Chemical Engineering, Jishou University, Jishou 416000 (China); Yao Shouzhuo [State Key Laboratory of Chemo/Biosensing and Chemometrics, Hunan University, Changsha 410082 (China)

    2010-02-28

    A novel composite material of multi-walled carbon nanotubes (MWNTs)-Sudan IV molecularly imprinted polymers (MIPs) was prepared by surface molecular imprinting technique in combination with sol-gel technology. The MWNTs-MIPs were evaluated by scanning electron micrograph (SEM), Fourier transform infrared spectroscopy (FT-IR), and adsorption experiments. The results showed that the MWNTs-MIPs exhibited good selective recognition to Sudan IV. The maximum saturated binding capacity (Q{sub max}) is 63.2 {mu}mol g{sup -1}. Applied as sorbent, the MWNTs-MIPs were used for the determination of trace Sudan IV in chilli powder by on-line solid-phase extraction-high-performance liquid chromatography (SPE-HPLC). The results showed that an enrichment factor of 741 was achieved with a loading flow rate of 1.0 mL min{sup -1} for sampling 50 mL. The MWNTs-MIPs provided a fast and convenience determination platform for Sudan IV in real samples.

  19. Simple and quick determination of analgesics and other contaminants of emerging concern in environmental waters by on-line solid phase extraction coupled to liquid chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Ferrer-Aguirre, Alejandra; Romero-González, Roberto; Vidal, J L Martínez; Frenich, Antonia Garrido

    2016-05-13

    A simple and quick analytical method has been developed for the determination of pharmaceutical compounds in water. An on-line solid-phase extraction (SPE) coupled to liquid chromatography-tandem mass spectrometry (LC-MS/MS) method has been optimized to determine 7 contaminants of emerging concern in environmental waters at ngL(-1) levels. This procedure requires minimal sample handling and small sample volume (900μL) with a total running time of 18min. Several SPE parameters were evaluated and optimized in order to achieve a high sample throughput. Therefore sample volume, carryover and reusability of the cartridges were evaluated. Performance characteristics were evaluated and good linearity was obtained (R(2)>0.98). Recoveries were evaluated in spiked samples at three concentrations and the values ranged from 71 to 104%. Intra and inter-day precision was lower than 10 and 13% respectively. Limits of quantification were equal to or lower than 10ngL(-1), except for 1,7-dimethylxanthine (20ngL(-1)) and ibuprofen (50ngL(-1)). The method was applied to 20 environmental water samples, and ibuprofen was the compound most widely detected at concentrations up to 42.06μgL(-1), whereas the other compounds were detected in fewer samples at lower concentrations (up to 15.99μgL(-1)).

  20. On-line solid-phase extraction coupled to ultra-performance liquid chromatography with tandem mass spectrometry detection for the determination of benzotriazole UV stabilizers in coastal marine and wastewater samples

    Energy Technology Data Exchange (ETDEWEB)

    Montesdeoca-Esponda, Sarah; Sosa-Ferrera, Zoraida; Santana-Rodriguez, Jose Juan [Universidad de Las Palmas de Gran Canaria, Departamento de Quimica, Las Palmas de Gran Canaria (Spain)

    2012-05-15

    Benzotriazoles are a group of UV absorbing compounds considered emerging contaminants that are used in different personal care products, and therefore, it is of high interest to develop sensitive and fast methods for investigating their presence in the environment. In this work, we present the development and application of a novel method based on on-line solid-phase extraction coupled to ultra-performance liquid chromatography with tandem mass spectrometry detection (SPE-UPLC-MS/MS) for the determination of seven benzotriazole UV stabilizers (BUVSs) in coastal marine and wastewater samples. This process is compared with a conventional off-line SPE procedure followed by UPLC-MS/MS. The parameters affecting the performance of the sample preparation and determination processes were evaluated. The results indicate that the on-line procedure provides for better sensitivity and reproducibility and is faster and easier than the off-line procedure. The detection limits and quantification limits achieved were in the range of 0.6-4.1 ng circle L{sup -1} and 2.1-14 ng circle L{sup -1} and relative standard deviation between 6.2 and 10 %. The developed method was applied to coastal marine and wastewater samples from Gran Canaria Island (Spain). All of the BUVSs studied were detected in the samples from wastewater treatment plants and two were found in the seawater samples (UV P in the range of 2.8-4.4 ng circle L{sup -1} and UV 360 between 3.6 and 5.2 ng circle L{sup -1}). (orig.)

  1. Preliminary results on the determination of ultratrace amounts of cadmium in tea samples using a flow injection on-line solid phase extraction separation and preconcentration technique to couple with a sequential injection hydride generation atomic fluorescence spectrometry.

    Science.gov (United States)

    Duan, Taicheng; Song, Xuejie; Jin, Dan; Li, Hongfei; Xu, Jingwei; Chen, Hangting

    2005-10-31

    In this work, a method was developed for determination of ultra-trace levels of Cd in tea samples by atomic fluorescence spectrometry (AFS). A flow injection solid phase extraction (FI-SPE) separation and preconcentration technique, to on-line couple with a sequential injection hydride generation (SI-HG) technique is employed in this study. Cd was preconcentrated on the SPE column, which was made from a neutral extractant named Cyanex 923, while other matrix ions or interfering ions were completely or mostly separated off. Conditions for the SPE separation and preconcentration, as well as conditions for the HG technique, were studied. Due to the separation of interfering elements, Cd hydride generation efficiency could be greatly enhanced with the sole presence of Co(2+) with a concentration of 200mugL(-1), which is much lower than those in other works previously reported. Interferences on both the Cd separation and preconcentration, and Cd hydride generation (HG) were investigated; it showed that both the separation and preconcentration system, and the HG system had a strong anti-interference ability. The SPE column could be repeatedly used at least 400 times, a R.S.D. of 0.97% was obtained for 6 measurements of Cd with 0.2mugL(-1) and a correlation coefficiency of 1.0000 was obtained for the measurement of a series of solutions with Cd concentrations from 0.1 to 2mugL(-1). The method has a low detection limit of 10.8ngL(-1) for a 25mL solution and was successfully validated by using two tea standard reference materials (GBW08513 and GBW07605).

  2. On-line solid-phase extraction coupled with high-performance liquid chromatography and tandem mass spectrometry (SPE-HPLC-MS-MS) for quantification of bromazepam in human plasma: an automated method for bioequivalence studies.

    Science.gov (United States)

    Gonçalves, José Carlos Saraiva; Monteiro, Tânia Maria; Neves, Claúdia Silvana de Miranda; Gram, Karla Regina da Silva; Volpato, Nádia Maria; Silva, Vivian A; Caminha, Ricardo; Gonçalves, Maria do Rocio Bencke; Santos, Fábio Monteiro Dos; Silveira, Gabriel Estolano da; Noël, François

    2005-10-01

    A validated method for on-line solid-phase extraction coupled with high-performance liquid chromatography tandem mass spectrometry (SPE-HPLC-MS-MS) is described for the quantification of bromazepam in human plasma. The method involves a dilution of 300 muL of plasma with 100 muL of carbamazepine (2.5 ng/mL), used as internal standard, vortex-mixing, centrifugation, and injection of 100 muL of the supernate. The analytes were ionized using positive electrospray mass spectrometry then detected by multiple reaction monitoring (MRM). The m/z transitions 316-->182 (bromazepam) and 237-->194 (carbamazepine) were used for quantification. The calibration curve was linear from 1 ng/mL (limit of quantification) to 200 ng/mL. The retention times of bromazepam and carbamazepine were 2.6 and 3.2 minutes, respectively. The intraday and interday precisions were 3.43%-15.45% and 5.2%-17%, respectively. The intraday and interday accuracy was 94.00%-103.94%. This new automated method has been successfully applied in a bioequivalence study of 2 tablet formulations of 6 mg bromazepam: Lexotan(R) from Produtos Roche Químicos e Farmacêuticos SA, Rio de Janeiro, Brazil (reference) and test formulation from Laboratórios Biosintética Ltda, São Paulo, Brazil. Because the 90% CI of geometric mean ratios between reference and test were completely included in the 80%-125% interval, the 2 formulations were considered bioequivalent. The comparison of different experimental conditions for establishing a dissolution profile in vitro along with our bioavailability data further allowed us to propose rationally based experimental conditions for a dissolution test of bromazepam tablets, actually lacking a pharmacopeial monograph.

  3. Fast and simple screening for the simultaneous analysis of seven metabolites derived from five volatile organic compounds in human urine using on-line solid-phase extraction coupled with liquid chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Chiang, Wen-Chieh; Chen, Chao-Yu; Lee, Ting-Chen; Lee, Hui-Ling; Lin, Yu-Wen

    2015-01-01

    Recently, the International Agency for Research on cancer classified outdoor air pollution and particulate matter from outdoor air pollution as carcinogenic to humans (IARC Group 1), based on sufficient evidence of carcinogenicity in humans and experimental animals and strong mechanistic evidence. In particular, a wide variety of volatile organic compounds (VOCs) are volatized or released into the atmosphere and can become ubiquitous, as they originate from many different natural and anthropogenic sources, such as paints, pesticides, vehicle exhausts, cooking fumes, and tobacco smoke. Humans may be exposed to VOCs through inhalation, ingestion, or dermal contact, which may increase the risk of leukemia, birth defects, neurocognitive impairment, and cancer. Therefore, the focus of this study was the development of a simple, effective and rapid sample preparation method for the simultaneous determination of seven metabolites (6 mercaptic acids+t,t-muconic acid) derived from five VOCs (acrylamide, 1,3-butadiene, acrylonitrile, benzene, and xylene) in human urine by using automated on-line solid-phase extraction (SPE) coupled with liquid chromatography-electrospray tandem mass spectrometry (LC-MS/MS). An aliquot of each diluted urinary sample was directly injected into an autosampler through a trap column to reduce contamination, and then the retained target compounds were eluted by back-flush mode into an analytical column for separation. Negative electrospray ionization tandem mass spectrometry was utilized for quantification. The coefficients of correlation (r(2)) for the calibration curves were greater than 0.995. Reproducibility was assessed by the precision and accuracy of intra-day and inter-day precision, which showed results for coefficient of variation (CV) that were low 0.9 to 6.6% and 3.7 to 8.5%, respectively, and results for recovery that ranged from 90.8 to 108.9% and 92.1 to 107.7%, respectively. The limits of detection (LOD) and limits of

  4. Feasibility of the direct coupling of solid-phase extraction-pipette tips with a programmed-temperature vaporiser for gas chromatographic analysis of drugs in plasma

    NARCIS (Netherlands)

    van Hout, M.W J; van Egmond, W.M A; Franke, J.P.; de Zeeuw, R.A; de Jong, G.J.

    2002-01-01

    Solid-phase extraction-pipette tips (SPE-PTs) were used for micro solid-phase extraction of lidocaine and diazepam from plasma. Off-line extraction was followed by on-line desorption. On-line desorption was carried out by direct coupling of the SPE-PTs with the liner of the programmed-temperature va

  5. Magnetic Solid Phase Extraction Applied to Food Analysis

    Directory of Open Access Journals (Sweden)

    Israel S. Ibarra

    2015-01-01

    Full Text Available Magnetic solid phase extraction has been used as pretreatment technique for the analysis of several compounds because of its advantages when it is compared with classic methods. This methodology is based on the use of magnetic solids as adsorbents for preconcentration of different analytes from complex matrices. Magnetic solid phase extraction minimizes the use of additional steps such as precipitation, centrifugation, and filtration which decreases the manipulation of the sample. In this review, we describe the main procedures used for synthesis, characterization, and application of this pretreatment technique which were applied in food analysis.

  6. Resolution of an intense sweetener mixture by use of a flow injection sensor with on-line solid-phase extraction. Application to saccharin and aspartame in sweets and drinks.

    Science.gov (United States)

    Capitán-Vallvey, L F; Valencia, M C; Arana Nicolás, E; García-Jiménez, J F

    2006-05-01

    An integrated solid-phase spectrophotometry-FIA method is proposed for simultaneous determination of the mixture of saccharin (1,2-benzisothiazol-3(2H)-one-1,1-dioxide; E-954) (SA) and aspartame (N-L-alpha-aspartyl-L-phenylalanine-1-methyl ester; E-951) (AS). The procedure is based on on-line preconcentration of AS on a C18 silica gel minicolumn and separation from SA, followed by measurement, at lambda = 210 nm, of the absorbance of SA which is transiently retained on the adsorbent Sephadex G-25 placed in the flow-through cell of a monochannel FIA setup using pH 3.0 orthophosphoric acid-dihydrogen phosphate buffer, 3.75x10(-3) mol L(-1), as carrier. Subsequent desorption of AS with methanol enables its determination at lambda = 205 nm. With a sampling frequency of 10 h(-1), the applicable concentration range, the detection limit, and the relative standard deviation were from 1.0 to 200.0 microg mL(-1), 0.30 microg mL(-1), and 1.0% (80 microg mL(-1), n = 10), respectively, for SA and from 10.0 to 200.0 microg mL(-1), 1.4 microg mL(-1), and 1.6% (100 microg mL(-1), n = 10) for AS. The method was used to determine the amounts of aspartame and saccharin in sweets and drinks. Recovery was always between 99 and 101%. The method enabled satisfactory determination of blends of SA and AS in low-calorie and dietary products and the results were compared with those from an HPLC reference method.

  7. Solid phase extraction method for determination of mitragynine in ...

    African Journals Online (AJOL)

    mitragynine in urine and its application to mitragynine excretion ... Purpose: To develop a solid phase extraction (SPE) method that utilizes reverse-phase high performance .... solution of MG (1 mg/mL) which was further ... Facility, Prince of Songkla University and carried ..... d), which permit unrestricted use, distribution,.

  8. On-line solid phase extraction-high performance liquid chromatography–isotope dilution–tandem mass spectrometry approach to quantify N,N-diethyl-m-toluamide and oxidative metabolites in urine

    Energy Technology Data Exchange (ETDEWEB)

    Kuklenyik, Peter; Baker, Samuel E.; Bishop, Amanda M.; Morales-A, Pilar; Calafat, Antonia M., E-mail: aic7@cdc.gov

    2013-07-17

    Graphical abstract: -- Highlights: •A fast assay to quantify the concentrations of N,N-Diethyl-m-Toluamide and two urinary metabolites was developed •It uses online SPE, reversed phase HPLC and tandem mass spectrometry •The method is precise and accurate with limits of detection ≤1 ng mL{sup −1} -- Abstract: Human exposure to N,N-diethyl-m-toluamide (DEET) occurs because of the widespread use of DEET as an active ingredient in insect repellents. However, information on the extent of such exposure is rather limited. Therefore, we developed a fast on-line solid phase extraction–high performance liquid chromatography–isotope dilution tandem mass spectrometry (HPLC-MS/MS) method to measure in urine the concentrations of DEET and two of its oxidative metabolites: N,N-diethyl-3-(hydroxymethyl)benzamide and 3-(diethylcarbamoyl)benzoic acid (DCBA). To the best of our knowledge, this is the first HPLC-MS/MS method for the simultaneous quantification of DEET and its select metabolites in human urine. After enzymatic hydrolysis of the conjugated species in 0.1 mL of urine, the target analytes were retained and pre-concentrated on a monolithic column, separated from each other and from other urinary biomolecules on a reversed-phase analytical column, and detected by atmospheric pressure chemical ionization in positive ion mode. The limits of detection ranged from 0.1 ng mL{sup −1} to 1.0 ng mL{sup −1}, depending on the analyte. Accuracy ranged between 90.4 and 104.9%, and precision ranged between 5.5 and 13.1% RSD, depending on the analyte and the concentration. We tested the usefulness of this method by analyzing 75 urine samples collected anonymously in the Southeastern United States in June 2012 from adults with no known exposure to DEET. Thirty eight samples (51%) tested positive for at least one of the analytes. We detected DCBA most frequently and at the highest concentrations. Our results suggest that this method can be used for the analysis of a large

  9. A single-step pesticide extraction and clean-up multi-residue analytical method by selective pressurized liquid extraction followed by on-line solid phase extraction and ultra-high-performance liquid chromatography-tandem mass spectrometry for complex matrices.

    Science.gov (United States)

    Rodrigues, Elsa Teresa; Pardal, Miguel Ângelo; Salgueiro-González, Noelia; Muniategui-Lorenzo, Soledad; Alpendurada, Maria Fátima

    2016-06-24

    Pesticides, a group of compounds linked to human activity, may, when in toxic levels, have a profound effect on water quality, and hence result in adverse consequences to aquatic life and ultimately to human health. Analytical challenges arise when successfully trying to determine these levels in environmental complex matrices. Therefore, fast, simple, sensitive and selective analytical methodologies for multi-residue determination of pesticides (atrazine, azoxystrobin, bentazon, λ-cyhalothrin, penoxsulam and terbuthylazine) in sediment, macrophytes (algae and aquatic plants) and aquatic animals were developed and validated. The established methods were matrix-dependent and were based on Selective Pressurized Liquid Extraction (SPLE) followed by on-line Solid Phase Extraction and Ultra Performance Liquid Chromatography-tandem Mass Spectrometry (on-line SPE-UPLC-ESI-MS/MS). This cutting-edge research methodology uses a small amount of sample, is time saving and reduces the use of organic solvents in compliance with Green Chemistry principles. The analytical features were adequate for all compounds in all studied matrices. The established methodology was applied on real marine samples and no pesticide concentrations above their respective method quantification limits were measured in sediments or aquatic plants. However, terbuthylazine was found in the macroalgae Ulva spp. (108ngg(-1)dw) and all the prospected pesticides were measured above their respective method quantification limits in the bivalve Scrobicularia plana (atrazine: 48ngg(-1)dw, azoxystrobin: 64ngg(-1)dw, bentazon: 33ngg(-1)dw, λ-cyhalothrin: 2531ngg(-1)dw, penoxsulam: 50ngg(-1)dw, and terbuthylazine: 44ngg(-1)dw).

  10. Chromatography, solid-phase extraction, and capillary electrochromatography with MIPs.

    Science.gov (United States)

    Tóth, Blanka; Horvai, George

    2012-01-01

    Most analytical applications of molecularly imprinted polymers are based on their selective adsorption properties towards the template or its analogs. In chromatography, solid phase extraction and electrochromatography this adsorption is a dynamic process. The dynamic process combined with the nonlinear adsorption isotherm of the polymers and other factors results in complications which have limited the success of imprinted polymers. This chapter explains these problems and shows many examples of successful applications overcoming or avoiding the problems.

  11. Fuel spill identification using solid-phase extraction and solid-phase microextraction. 1. Aviation turbine fuels.

    Science.gov (United States)

    Lavine, B K; Brzozowski, D M; Ritter, J; Moores, A J; Mayfield, H T

    2001-12-01

    The water-soluble fraction of aviation jet fuels is examined using solid-phase extraction and solid-phase microextraction. Gas chromatographic profiles of solid-phase extracts and solid-phase microextracts of the water-soluble fraction of kerosene- and nonkerosene-based jet fuels reveal that each jet fuel possesses a unique profile. Pattern recognition analysis reveals fingerprint patterns within the data characteristic of fuel type. By using a novel genetic algorithm (GA) that emulates human pattern recognition through machine learning, it is possible to identify features characteristic of the chromatographic profile of each fuel class. The pattern recognition GA identifies a set of features that optimize the separation of the fuel classes in a plot of the two largest principal components of the data. Because principal components maximize variance, the bulk of the information encoded by the selected features is primarily about the differences between the fuel classes.

  12. Silica supported Fe(3)O(4) magnetic nanoparticles for magnetic solid-phase extraction and magnetic in-tube solid-phase microextraction: application to organophosphorous compounds.

    Science.gov (United States)

    Moliner-Martinez, Y; Vitta, Yosmery; Prima-Garcia, Helena; González-Fuenzalida, R A; Ribera, Antonio; Campíns-Falcó, P; Coronado, Eugenio

    2014-03-01

    This work demonstrates the application of silica supported Fe3O4 nanoparticles as sorbent phase for magnetic solid-phase extraction (MSPE) and magnetic on-line in-tube solid-phase microextraction (Magnetic-IT-SPME) combined with capillary liquid chromatography-diode array detection (CapLC-DAD) to determine organophosphorous compounds (OPs) at trace level. In MSPE, magnetism is used as separation tool while in Magnetic-IT-SPME, the application of an external magnetic field gave rise to a significant improvement of the adsorption of OPs on the sorbent phase. Extraction efficiency, analysis time, reproducibility and sensitivity have been compared. This work showed that Magnetic-IT-SPME can be extended to OPs with successful results in terms of simplicity, speed, extraction efficiency and limit of detection. Finally, wastewater samples were analysed to determine OPs at nanograms per litre.

  13. Preparation of an epitope-imprinted polymer with antibody-like selectivity for beta2-microglobulin and application in serum sample analysis with a facile method of on-line solid-phase extraction coupling with high performance liquid chromatography.

    Science.gov (United States)

    Yang, Fangfang; Deng, Dandan; Dong, Xiangchao; Lin, Shen

    2017-03-09

    Molecularly imprinted polymers (MIPs) for protein recognition have great application potential in the biological analysis. However, preparation of protein imprinted polymer is still facing challenge. Beta2-microglobulin (β2m) is a protein biomarker that can be used in diagnosis of different diseases. In this research, a novel MIP with ability of β2m recognition has been developed by epitope and surface-confined imprinting approaches. A peptide with sequence of MIQRTPKIQ was selected as template. A strategy of combination of hierarchical imprinting and template immobilization was employed in the β2m-MIP synthesis. Imprinted binding sites with open-entrance have been created that have good accessibility for β2m and facilitated fast reversible binding kinetics. The experimental results demonstrated that the MIP has good selectivity. It can differentiate the template from peptide with different sequence and distinguish the β2m from other proteins with similar size and pI values. After binding property study of the β2m-MIP, a method of β2m determination in serum was established in which β2m was on-line extracted by MIP and analyzed by HPLC process. The recoveries for spiked serum was ≥83% with RSD <1.1%, indicating that the method has good accuracy and precisions. The LOD and LOQ were 0.058 and 0.195mgL(-1) respectively, which meet the requirements of the β2m analysis. The successful application of the β2m-MIP demonstrated that β2m has reversible binding on the MIP with a kinetics that can meet the requirements of the HPLC analysis. It also indicated that the β2m-MIP has good mechanical strength and reusability that can be applied reliably in the practical analysis. As a synthetic antibody, β2m-MIP is advantageous compared to the biological molecules.

  14. Generic solid phase extraction-liquid chromatography-tandem mass spectrometry method for fast determination of drugs in biological fluids

    NARCIS (Netherlands)

    Schellen, A.; Ooms, B.; Lagemaat, D. van de; Vreeken, R.; Dongen, W.D. van

    2003-01-01

    A generic method was developed for the fast determination of a wide range of drugs in serum or plasma. The methodology comprises generic solid-phase extraction, on-line coupled to gradient HPLC with tandem mass spectrometric detection (SPE-LC-MS/MS). The individual components of the SPE-LC-MS/MS sys

  15. Sequential injection/bead injection lab-on-valve schemes for on-line solid phase extraction and preconcentration of ultra-trace levels of heavy metals with determination by ETAAS and ICPMS

    DEFF Research Database (Denmark)

    Wang, Jianhua; Hansen, Elo Harald; Miró, Manuel

    2003-01-01

    This communication presents an overview of the state-of-the-art of the exploitation of sequential injection (SI)-bead injection (BI)-lab-on-valve (LOV) schemes for automatic on-line sample pre-treatments interfaced with ETAAS and ICPMS detection as conducted in the authors' group. The discussions......, that is, the hydrophilic SP Sephadex C-25 cation exchange and iminodiacetate based Muromac A-1 chelating resins, and the hydrophobic poly(tetrafluoroethylene) (PTFE) and poly(styrene-divinylbenzene) copolymer alkylated with octadecyl groups (C18-PS/DVB). Using ETAAS as detection device, the easy......-to-handle hydrophilic renewable reactors hold the features of improved R.S.D.s and LODs as compared to those operated in the conventional, permanent mode, in addition to the elimination of flow resistance. The hydrophobic columns fall into two categories, that is, the renewable one packed with C18-PS/DVB beads entails...

  16. Simultaneous determination of Pb and Cd in seafood by ICP OES with on-line pre-concentration by solid phase extraction with amberlite XAD-4 after complex formation with DDTP

    Directory of Open Access Journals (Sweden)

    Éder José dos Santos

    2013-02-01

    Full Text Available An on-line method for Cd and Pb pre-concentration and simultaneous determination in acid digested seafood by inductively coupled plasma optical emission spectrometry (ICP OES was developed. The on-line pre-concentration was based on the complex formation of the analytes with the ammonium salt of O,O-diethyldithiophosphate (DDTP and using the Amberlite XAD-4 resin as a solid support in a homemade column. Different conditions of the flow injection system, such as solutions flow rates, nebulizer pressure and eluent concentration were optimized. Three certified reference materials of lobster hepatopancreas, dogfish liver and fish protein, three samples of fish muscle and three samples of shrimp were digested with HNO3, H2O2 and H2SO4 in a microwave system under reflux. DDTP was added in the solutions obtained, and the mixture was injected in the FI system. Calibration curves for Cd and Pb were obtained using the standard solutions in the concentration range 0.05-0.5 µg mL-1 in the digestion medium, submitted to the same pre-concentration procedure. The quantification limits (3.3 x LOD for 5 min of pre-concentration time were 0.005 mg kg-1 Cd2+ and 0.1 mg kg-1 Pb2+ in the sample of fish or shrimp in natura, considering 1.0 g of the sample in a final volume of 50 mL. The agreement of the obtained concentrations with the certified ones (Student t-test, 95% confidence and the recoveries of spiked real samples, from 90 to 120%, demonstrated good accuracy. Precision was also adequate, with relative standard deviations from 2 to 13%. The method was accurate, precise and certainly could be applied to the digested samples of different natures.

  17. Determination of Cd in biological samples by flame AAS following on-line preconcentration by complexation with O,O-diethyldithiophosphate and solid phase extraction with Amberlite XAD-4.

    Science.gov (United States)

    Santos, Eder José Dos; Herrmann, Amanda Beatriz; Ribeiro, Anderson Schwingel; Curtius, Adilson José

    2005-01-30

    A method for the on-line preconcentration of Cd based on its complex formation with the ammonium salt of O,O-diethylditiophosphate (DDTP) and using the Amberlite XAD-4 resin as a solid support in a column is proposed. Cadmium was detected by flame atomic absorption spectrometry. Different conditions, such as complexing agent concentration, preconcentration time, solutions flow rates and nature and concentration of the eluent were optimized. Different detection limits (LODs) could be established by using different preconcentration times, between 30s and 5min, with corresponding LODs from 5 to 1mugL(-1), respectively. The method was validated by analyzing five biological certified samples. The relative standard deviation was usually around 3%, indicating a very good precision. The found concentrations values are in agreement with the certified ones, according to the t-test, for a confidence level of 95%. Enriched seawaters were also analyzed, and the recoveries were between 93 and 108%. The FI method is very simple and probably can be coupled to other measuring analytical techniques.

  18. Molecularly imprinted solid phase extraction of fluconazole from pharmaceutical formulations.

    Science.gov (United States)

    Manzoor, S; Buffon, R; Rossi, A V

    2015-03-01

    This work encompasses a direct and coherent strategy to synthesise a molecularly imprinted polymer (MIP) capable of extracting fluconazole from its sample. The MIP was successfully prepared from methacrylic acid (functional monomer), ethyleneglycoldimethacrylate (crosslinker) and acetonitrile (porogenic solvent) in the presence of fluconazole as the template molecule through a non-covalent approach. The non-imprinted polymer (NIP) was prepared following the same synthetic scheme, but in the absence of the template. The data obtained from scanning electronic microscopy, infrared spectroscopy, thermogravimetric and nitrogen Brunauer-Emmett-Teller plot helped to elucidate the structural as well as the morphological characteristics of the MIP and NIP. The application of MIP as a sorbent was demonstrated by packing it in solid phase extraction cartridges to extract fluconazole from commercial capsule samples through an offline analytical procedure. The quantification of fluconazole was accomplished through UPLC-MS, which resulted in LOD≤1.63×10(-10) mM. Furthermore, a high percentage recovery of 91±10% (n=9) was obtained. The ability of the MIP for selective recognition of fluconazole was evaluated by comparison with the structural analogues, miconazole, tioconazole and secnidazole, resulting in percentage recoveries of 51, 35 and 32%, respectively.

  19. Determination of 3,4-methylenedioxymethamphetamine and its five main metabolites in rat urine by solid-phase extraction and high performance liquid chromatography with on line mass spectrometry.

    Science.gov (United States)

    Menet, Marie-Claude; Fonsart, Julien; Hervé, Françoise; Fompeydie, Dominique; Galliot-Guilley, Martine; Noble, Florence; Scherrmann, Jean-Michel

    2010-10-15

    The consumption of psychostimulant amphetamine-like drugs has increased significantly in recent years. Some MDMA metabolites are probably involved in the neurotoxicity and neurodegeneration caused by prolonged use rather than MDMA itself. We recently developed a method to analyze MDMA and its five main metabolites in rat plasma [7]. We have now fully validated this method to the quantification of these drugs in rat urine. We extracted MDMA and its metabolites with Oasis WCX cartridges, separated them on a Nucleodur C18 analytical column and quantified them by ion-trap mass spectrometry. Linearity was excellent: 12.5-1250ng/mL urine for HMA, HMMA, MDA and MDMA, 25-2500ng/mL for HHMA, and 150-7500ng/mL for HHA (r(2)>0.993 for all analytes). The lower limits of quantification were 12.5ng/mL urine for MDMA, MDA, HMA and HMMA, 25ng/mL for HHMA and 150ng/mL for HHA. Reproducibility was good (intra-assay precision=1.7-6.1%; inter-assay precision=0.6-5.7%), as was accuracy (intra-assay deviation=0.1-4.8%; inter-assay deviation=0.7-7.9%). Average recoveries were around 85.0%, except for HHMA (66.2%) and HHA (53.0%) (CVurine samples taken over 24h from rats given subcutaneous MDMA.

  20. A review on solid phase extraction of actinides and lanthanides with amide based extractants.

    Science.gov (United States)

    Ansari, Seraj A; Mohapatra, Prasanta K

    2017-05-26

    Solid phase extraction is gaining attention from separation scientists due to its high chromatographic utility. Though both grafted and impregnated forms of solid phase extraction resins are popular, the later is easy to make by impregnating a given organic extractant on to an inert solid support. Solid phase extraction on an impregnated support, also known as extraction chromatography, combines the advantages of liquid-liquid extraction and the ion exchange chromatography methods. On the flip side, the impregnated extraction chromatographic resins are less stable against leaching out of the organic extractant from the pores of the support material. Grafted resins, on the other hand, have a higher stability, which allows their prolong use. The goal of this article is a brief literature review on reported actinide and lanthanide separation methods based on solid phase extractants of both the types, i.e., (i) ligand impregnation on the solid support or (ii) ligand functionalized polymers (chemically bonded resins). Though the literature survey reveals an enormous volume of studies on the extraction chromatographic separation of actinides and lanthanides using several extractants, the focus of the present article is limited to the work carried out with amide based ligands, viz. monoamides, diamides and diglycolamides. The emphasis will be on reported applied experimental results rather than on data pertaining fundamental metal complexation. Copyright © 2017 Elsevier B.V. All rights reserved.

  1. MOLECULAR IMPRINTED SOLID PHASE EXTRACTION FOR DETERMINATION OF ATRAZINE IN ENVIRONMENTAL SAMPLES

    Directory of Open Access Journals (Sweden)

    A. R. Koohpaei ، S. J. Shahtaheri ، M. R. Ganjali ، A. Rahimi Forushani

    2008-10-01

    Full Text Available Solid phase extraction is one of the major applications of molecularly imprinted polymers fields for clean-up of environmental and biological samples namely molecularly imprinted solid-phase extraction. In this study, solid phase extraction using the imprinted polymer has been optimized with the experimental design approach for a triazine herbicide, named atrazine with regard to the critical factors which influence the molecular imprinted solid phase extraction efficiency such as sample pH, concentration, flow-rate, volume, elution solvent, washing solvent and sorbent mass. Optimization methods that involve changing one factor at a time can be laborious. A novel approach for the optimization of imprinted solid-phase extraction using chemometrics is described. The factors were evaluated statistically and also validated with spiked water samples and showed a good reproducibility over six consecutive days as well as six within-day experiments. Also, in order to the evaluate efficiency of the optimized molecularly imprinted solid-phase extraction protocols, enrichment capacity, reusability and cross-reactivity of cartridges have been also evaluated. Finally, selective molecularly imprinted solid-phase extraction of atrazine was successfully demonstrated with a recovery above 90% for spiked drinking water samples. It was concluded that the chemometrics is frequently employed for analytical method optimization and based on the obtained results, it is believed that the central composite design could prove beneficial for aiding the molecularly imprinted polymer and molecularly imprinted solid-phase extraction development.

  2. New methods and materials for solid phase extraction and high performance liquid chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Dumont, Philip John [Iowa State Univ., Ames, IA (United States)

    1996-04-23

    This paper describes methods for solid phase extraction and high performance liquid chromatography (HPLC). The following are described: Effects of Resin Sulfonation on the Retention of Polar Organic Compounds in Solid Phase Extraction; Ion-Chromatographic Separation of Alkali Metals In Non-Aqueous Solvents; Cation-Exchange Chromatography in Non-Aqueous Solvents; and Silicalite As a Stationary Phase For HPLC.

  3. Novel materials and methods for solid-phase extraction and liquid chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Ambrose, Diana [Iowa State Univ., Ames, IA (United States)

    1997-06-24

    This report contains a general introduction which discusses solid-phase extraction and solid-phase micro-extraction as sample preparation techniques for high-performance liquid chromatography, which is also evaluated in the study. This report also contains the Conclusions section. Four sections have been removed and processed separately: silicalite as a sorbent for solid-phase extraction; a new, high-capacity carboxylic acid functionalized resin for solid-phase extraction; semi-micro solid-phase extraction of organic compounds from aqueous and biological samples; and the high-performance liquid chromatographic determination of drugs and metabolites in human serum and urine using direct injection and a unique molecular sieve.

  4. Recent developments in automatic solid-phase extraction with renewable surfaces exploiting flow-based approaches

    DEFF Research Database (Denmark)

    Miró, Manuel; Hartwell, Supaporn Kradtap; Jakmunee, Jaroon

    2008-01-01

    Solid-phase extraction (SPE) is the most versatile sample-processing method for removal of interfering species and/or analyte enrichment. Although significant advances have been made over the past two decades in automating the entire analytical protocol involving SPE via flow-injection approaches......,on-line SPE assays performed in permanent mode lack sufficient reliability as a consequence of progressively tighter packing of the bead reactor, contamination of the solid surfaces and potential leakage of functional moieties. This article overviews the current state-of-the-art of an appealing tool...... chemical-derivatization reactions, and it pinpoints the most common instrumental detection techniques utilized. We present and discuss in detail relevant environmental and bioanalytical applications reported in the past few years....

  5. Electroplating of nanostructured polyaniline-polypyrrole composite coating in a stainless-steel tube for on-line in-tube solid phase microextraction.

    Science.gov (United States)

    Asiabi, Hamid; Yamini, Yadollah; Seidi, Shahram; Esrafili, Ali; Rezaei, Fatemeh

    2015-06-05

    In this work, a novel and efficient on-line in-tube solid phase microextraction method followed by high performance liquid chromatography was developed for preconcentration and determination of trace amounts of parabens. A nanostructured polyaniline-polypyrrole composite was electrochemically deposited on the inner surface of a stainless steel tube and used as the extraction phase. Several important factors that influence the extraction efficiency, including type of solid-phase coating, extraction and desorption times, flow rates of the sample solution and eluent, pH, and ionic strength of the sample solution were investigated and optimized. Under the optimal conditions, the limits of detection were in the range of 0.02-0.04 μg L(-1). This method showed good linearity for parabens in the range of 0.07-50 μg L(-1), with coefficients of determination better than 0.998. The intra- and inter-assay precisions (RSD%, n=3) were in the range of 5.9-7.0% and 4.4-5.7% at three concentration levels of 2, 10, and 20 μg L(-1), respectively. The extraction recovery values for the spiked samples were in the acceptable range of 80.3-90.2%. The validated method was successfully applied for analysis of methyl-, ethyl-, and propyl parabens in some water, milk, and juice samples. Copyright © 2015 Elsevier B.V. All rights reserved.

  6. 在线固相萃取-超高效液相色谱-串联质谱法测定乳制品中双酚A等4种内分泌干扰物%Determination of 4 Environmental Endocrine Disruptors Involving Bisphenol A in Dairy Products by On-line Solid Phase Extraction Coupled with Liquid Chromatography-Tandem Mass Spectrometry

    Institute of Scientific and Technical Information of China (English)

    张品; 张晶; 陈洁君; 段鹤君; 邵兵

    2014-01-01

    A simple analytical method by means of on-line solid phase extraction followed liquid chromatography-tandem mass spectrometry ( SPE-LC-MS/MS) was developed for the simultaneous quantitation of 4 endocrine disruptors ( triclosan, triclocarban, bisphenol A and nonylphenol) in dairy products. Infant formula and milk samples were dissolved in acetic acid buffer and hydrolyzed by β-glucuronidase/arylsulfatase. Acetonitrile was used as the extract. Then, the mixture was freeze-centrifuged for 10 min and the supernatant was diluted with water, and analyzed via on-line SPE-LC-MS/MS. The sample extracts were concentrated by an Xbridge C8 cartridge and separated on a BEH C18 column with a gradient mobile phase of methanol and water; then analyzed by triple quadrupole mass spectrometry. Mass acquisition was conducted under negative electrospray ionization mode. Quantification was performed by isotopic internal standard calibration. Acceptable linearity (R2>0. 99) was achieved over the range of 0. 005-5. 0 μg/L, with limits of quantification of 0. 03-1. 0μg/kg. Average recoveries of four target compounds (spiked at three concentration levels) ranged from 80. 2%-106. 7%,with relative standard deviation less than 15%. Due to its rapidity, simplicity, and high sensitivity, the method is suitable for the analysis of endocrine disruptors in dairy products. It has been applied in the analysis of raw milk and milk products collected in Beijing. As a result, nonylphenol was found with a high detectable frequency.%建立了乳制品中三氯生、三氯卡班、双酚A和壬基酚4种内分泌干扰物的在线固相萃取超高压液相色谱-串联质谱(On-line SPE LC-MS/MS)检测方法。液态乳制品或奶粉样品中加入乙酸缓冲液,目标物经β-葡糖醛酸苷肽酶/芳基磺酸酯酶酶解后,用乙腈提取,冷冻离心10 min后,取上清液,用水稀释,在线固相萃取串联质谱法测定。样品溶液经Xbridge C8柱富集,BEH C18色谱柱分离,甲醇和

  7. Different methods to select the best extraction system for solid-phase extraction.

    Science.gov (United States)

    Bielicka-Daszkiewicz, Katarzyna

    2015-02-01

    The optimization methods for planning a solid-phase extraction experiment are presented. These methods are based on a study of interactions between different parts of an extraction system. Determination of the type and strength of interaction depends on the physicochemical properties of the individual components of the system. The main parameters that determine the extraction properties are described in this work. The influence of sorbents' and solvents' polarity on extraction efficiency, Hansen solubility parameters and breakthrough volume determination on sorption and desorption extraction step are discussed.

  8. Utilizing ion-pairing hydrophilic interaction chromatography solid phase extraction for efficient glycopeptide enrichment in glycoproteomics

    DEFF Research Database (Denmark)

    Mysling, Simon; Palmisano, Giuseppe; Højrup, Peter;

    2010-01-01

    Glycopeptide enrichment is a prerequisite to enable structural characterization of protein glycosylation in glycoproteomics. Here we present an improved method for glycopeptide enrichment based on zwitter-ionic hydrophilic interaction chromatography solid phase extraction (ZIC-HILIC SPE...

  9. Molecularly imprinted polymers: New molecular recognition materials for selective solid-phase extraction of organic compounds

    OpenAIRE

    Martín Esteban, A.

    2001-01-01

    During the last few years molecularly imprinted polymers have appeared as new selective sorbents for solid-phase extraction of organic compounds in different samples. Molecular imprinting technology involves the preparation of a polymer with specific recognition sites for certain molecules. Once the polymer has been obtained, it can be used in solid-phase extraction protocols, where a careful selection of the most appropriate solvents to be used in the different steps (sample loading, washing...

  10. Recent Application of Solid Phase Based Techniques for Extraction and Preconcentration of Cyanotoxins in Environmental Matrices.

    Science.gov (United States)

    Mashile, Geaneth Pertunia; Nomngongo, Philiswa N

    2017-03-04

    Cyanotoxins are toxic and are found in eutrophic, municipal, and residential water supplies. For this reason, their occurrence in drinking water systems has become a global concern. Therefore, monitoring, control, risk assessment, and prevention of these contaminants in the environmental bodies are important subjects associated with public health. Thus, rapid, sensitive, selective, simple, and accurate analytical methods for the identification and determination of cyanotoxins are required. In this paper, the sampling methodologies and applications of solid phase-based sample preparation methods for the determination of cyanotoxins in environmental matrices are reviewed. The sample preparation techniques mainly include solid phase micro-extraction (SPME), solid phase extraction (SPE), and solid phase adsorption toxin tracking technology (SPATT). In addition, advantages and disadvantages and future prospects of these methods have been discussed.

  11. Developments in coupled solid-phase extraction-capillary electrophoresis 2013-2015.

    Science.gov (United States)

    Ramautar, Rawi; Somsen, Govert W; de Jong, Gerhardus J

    2016-01-01

    An overview of the design and application of coupled solid-phase extraction-capillary electrophoresis (SPE-CE) systems reported in the literature between July 2013 and June 2015 is provided in this paper. The present article is a continuation of our previous review papers on this topic which covered the time period 2000-2013 (Electrophoresis 2008, 29, 108-128; Electrophoresis 2010, 31, 44-54; Electrophoresis 2012, 33, 243-250; Electrophoresis 2014, 35, 128-137). The use of in-line and on-line SPE-CE approaches is treated and outlined in this review. Recent advancements, such as, for example, the use of aptamers as affinity material for in-line SPE-CE, the use of a bead string design for in-line fritless SPE-CE, and new interfacing techniques for the on-line coupling of SPE to CE, are outlined. Selected examples demonstrate the applicability of the coupled SPE-CE systems for biomedical, pharmaceutical, environmental, and food studies. A complete overview of the recent SPE-CE studies is given in table format, providing information on sample type, SPE sorbent, coupling mode, detection mode, and LOD. Finally, some general conclusions and perspectives are provided.

  12. Two-dimensional solid-phase extraction strategy for the selective enrichment of aminoglycosides in milk.

    Science.gov (United States)

    Shen, Aijin; Wei, Jie; Yan, Jingyu; Jin, Gaowa; Ding, Junjie; Yang, Bingcheng; Guo, Zhimou; Zhang, Feifang; Liang, Xinmiao

    2017-03-01

    An orthogonal two-dimensional solid-phase extraction strategy was established for the selective enrichment of three aminoglycosides including spectinomycin, streptomycin, and dihydrostreptomycin in milk. A reversed-phase liquid chromatography material (C18 ) and a weak cation-exchange material (TGA) were integrated in a single solid-phase extraction cartridge. The feasibility of two-dimensional clean-up procedure that experienced two-step adsorption, two-step rinsing, and two-step elution was systematically investigated. Based on the orthogonality of reversed-phase and weak cation-exchange procedures, the two-dimensional solid-phase extraction strategy could minimize the interference from the hydrophobic matrix existing in traditional reversed-phase solid-phase extraction. In addition, high ionic strength in the extracts could be effectively removed before the second dimension of weak cation-exchange solid-phase extraction. Combined with liquid chromatography and tandem mass spectrometry, the optimized procedure was validated according to the European Union Commission directive 2002/657/EC. A good performance was achieved in terms of linearity, recovery, precision, decision limit, and detection capability in milk. Finally, the optimized two-dimensional clean-up procedure incorporated with liquid chromatography and tandem mass spectrometry was successfully applied to the rapid monitoring of aminoglycoside residues in milk. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Determination of melamine in aquaculture feed samples based on molecularly imprinted solid-phase extraction.

    Science.gov (United States)

    Lian, Ziru; Liang, Zhenlin; Wang, Jiangtao

    2015-10-01

    This research highlights the application of highly efficient molecularly imprinted solid-phase extraction for the preconcentration and analysis of melamine in aquaculture feed samples. Melamine-imprinted polymers were synthesized employing methacrylic acid and ethylene glycol dimethacrylate as functional monomer and cross-linker, respectively. The characteristics of obtained polymers were evaluated by scanning electron microscopy, Fourier transform infrared spectroscopy and binding experiments. The imprinted polymers showed an excellent adsorption ability for melamine and were applied as special solid-phase extraction sorbents for the selective cleanup of melamine. An off-line molecularly imprinted solid-phase extraction procedure was developed for the separation and enrichment of melamine from aquaculture feed samples prior to high-performance liquid chromatography analysis. Optimum molecularly imprinted solid-phase extraction conditions led to recoveries of the target in spiked feed samples in the range 84.6-96.6% and the relative standard deviation less than 3.38% (n = 3). The aquaculture feed sample was determined, and there was no melamine found. The results showed that the molecularly imprinted solid-phase extraction protocols permitted the sensitive, uncomplicated and inexpensive separation and pre-treatment of melamine in aquaculture feed samples.

  14. LC-UV-solid-phase extraction-NMR-MS combined with a cryogenic flow probe and its application to the identification of compounds present in Greek oregano

    NARCIS (Netherlands)

    Exarchou, V.; Godejohann, M.; Beek, van T.A.; Gerothanassis, I.P.; Vervoort, J.J.M.

    2003-01-01

    Structure elucidation of natural products usually relies on a combination of NMR spectroscopy with mass spectrometry whereby NMR trails MS in terms of the minimum sample amount required. In the present study, the usefulness of on-line solid-phase extraction (SPE) in LC-NMR for peak storage after the

  15. SOLID PHASE EXTRACTION OF TRACE AMOUNTS OF ZINC AND ...

    African Journals Online (AJOL)

    ions in the water and food samples and satisfactory results were obtained. ... extraction, cloud point extraction, coprecipitation, membrane filtration .... Approximately 5.0 g of dry rice, spaghetti, bread and black tea samples were taken in four.

  16. Fast Analysis of Vitamin A and E in Animal Derived Foods by On-Line Solid Phase Extraction Coupled with High Performance Liquid Chromatography%在线固相萃取-高效液相色谱联用测定动物源食品中的维生素A、E

    Institute of Scientific and Technical Information of China (English)

    谢云峰; 王浩; 刘佟; 任丹丹; 杨永坛

    2014-01-01

    采用固相萃取与双梯度高效液相色谱联用技术,建立了一种在线固相萃取-高效液相色谱同时测定动物源食品中维生素A、E的分析方法。样品于80℃下皂化反应30 min,经离心沉淀后引入一维C8固相萃取柱,采用60%( V/V)甲醇溶液对目标物进行在线富集净化,然后通过阀切换将其转移至二维液相分析系统进行分离检测。考察了萃取填料、上样溶剂及洗脱条件对猪肝、鸡蛋和配方乳粉的维生素A、E富集和基质净化效果。结果表明,在优化条件下,方法线性范围为0.02~20 mg/L,线性相关系数R2≥0.9998,对维生素A、E的检出限(S/N=3)为3.0~30.0μg/L,实际样品加标回收率为87.3%~115.0%,相对标准偏差(RSD)为1.8%~4.6%。本方法操作简便,灵敏度高,可用于动物源食品中维生素A、E的快速测定。%An automated analytical method for simultaneous determination of vitamin A and E in livers, fortified infant formulae and eggs has been developed based on on-line solid phase extraction (SPE) coupled with a dual gradient high performance liquid chromatography system with column-switching. Firstly, food samples were centrifuged after saponified in mixture solution of anhydrous alcohol, potassium hydroxide and ascorbic acid at 80 ℃ for 30 min. Secondly, the saponified sample was loaded and washed on the first dimension extraction column using methanol-water (60∶40, V/V). Afterwards, the targeted analytes were trapped and enriched on the SPE column. Finally, the trapped analytes were transferred to the second dimension analysis column by valve-switching technique for the following separation and determination. Several key factors such as the type of SPE columns, elution buffer as well as pH of washing solution were optimized. The results showed that the calibration curves of vitamin A and E were linear in the range of 0 . 02-20 mg/L with correlation coefficient (R2) more than 0. 9998. In addition, the limits of detection

  17. Determination of Roxarsone in feeds using solid phase extraction and liquid chromatography with ultraviolet detection.

    Science.gov (United States)

    Sapp, R E; Davidson, S

    1993-01-01

    A method is presented for detection and quantitation of Roxarsone in poultry feed by liquid chromatography. The drug is extracted by phosphate buffer and determined by solid phase extraction and reversed-phase liquid chromatography. Recoveries of the sample spikes and fortified field samples agree closely with those obtained by the standard spectrophotometric method.

  18. Detection of ibuprofen and ciprofloxacin by solid-phase extraction and UV/Vis spectroscopy

    Science.gov (United States)

    Zhou, Zhengwei; Jiang, Jia Qian

    2012-07-01

    A simple and economic solid-phase extraction coupled with UV/Vis spectrophotometric method is described for the analysis of ibuprofen and ciprofloxacin. Following solid-phase extraction from model wastewater samples containing standard ibuprofen or ciprofloxacin, elutes were analyzed by a UV/Vis spectrophotometer at 225 nm for ibuprofen and 280 nm for ciprofloxacin. The assay was linear for both compounds with good coefficients of correlation. This method shows good recoveries for both compounds with 101.0 ± 9.8% for ibuprofen and 99.4 ± 11.8% ciprofloxacin.

  19. Determination of paraben preservatives in seafood using matrix solid-phase dispersion and on-line acetylation gas chromatography-mass spectrometry.

    Science.gov (United States)

    Djatmika, Rosalina; Hsieh, Chih-Chung; Chen, Jhih-Ming; Ding, Wang-Hsien

    2016-11-15

    An effective method for determining four commonly detected paraben preservatives (methyl, ethyl, propyl and butyl paraben) in marketed seafood is presented. This method employs matrix solid-phase dispersion (MSPD) before identification and quantification of the paraben preservatives via on-line acetylation gas chromatography-mass spectrometry (GC-MS). Parameters affecting the extraction efficiency of MSPD were optimized through a Box-Behnken design method. Under optimal condition, 0.5-g of freeze-dried seafood was mixed with 0.5-g of anhydrous sodium sulfate, and dispersed with 1.0-g of Florisil using vortex. After that, the blend was transferred to a glass column containing 1.5-g of silica gel+C18 (w/w, 9:1), which acted as clean-up co-sorbents. Then, target analytes were eluted with 12mL of acetonitrile. The extract was then derivatized on-line in the GC injection-port through reaction with acetic anhydride, and the identity and quantity of the target analytes were determined by the GC-MS system. The limits of quantitation (LOQs) were 0.2 to 1.0ng/g (dry weight). Preliminary results showed that the total concentrations of four selected parabens ranged from 16.7 to 44.7ng/g (dry weight).

  20. Characterization of rhamnolipids by liquid chromatography/mass spectrometry after solid-phase extraction.

    Science.gov (United States)

    Behrens, Beate; Engelen, Jeannine; Tiso, Till; Blank, Lars Mathias; Hayen, Heiko

    2016-04-01

    Rhamnolipids are surface-active agents with a broad application potential that are produced in complex mixtures by bacteria of the genus Pseudomonas. Analysis from fermentation broth is often characterized by laborious sample preparation and requires hyphenated analytical techniques like liquid chromatography coupled to mass spectrometry (LC-MS) to obtain detailed information about sample composition. In this study, an analytical procedure based on chromatographic method development and characterization of rhamnolipid sample material by LC-MS as well as a comparison of two sample preparation methods, i.e., liquid-liquid extraction and solid-phase extraction, is presented. Efficient separation was achieved under reversed-phase conditions using a mixed propylphenyl and octadecylsilyl-modified silica gel stationary phase. LC-MS/MS analysis of a supernatant from Pseudomonas putida strain KT2440 pVLT33_rhlABC grown on glucose as sole carbon source and purified by solid-phase extraction revealed a total of 20 congeners of di-rhamnolipids, mono-rhamnolipids, and their biosynthetic precursors 3-(3-hydroxyalkanoyloxy)alkanoic acids (HAAs) with different carbon chain lengths from C8 to C14, including three rhamnolipids with uncommon C9 and C11 fatty acid residues. LC-MS and the orcinol assay were used to evaluate the developed solid-phase extraction method in comparison with the established liquid-liquid extraction. Solid-phase extraction exhibited higher yields and reproducibility as well as lower experimental effort.

  1. Extraction of Pesticides from Plants using Solid Phase ...

    African Journals Online (AJOL)

    NICO

    that may render trace analysis of pesticide residues almost impossible. .... mixing. 100 µL of the internal standard stock solution was added to each mixture. ... graph. 2.5.2. Extraction of Pesticides from Plant Samples by QuEChERS. Pesticide ...

  2. Solid-phase extraction procedures in systematic toxicological analysis

    NARCIS (Netherlands)

    Franke, J.P.; de Zeeuw, R.A

    1998-01-01

    In systematic toxicological analysis (STA) the substance(s) present is (are) not known at the start of the analysis. in such an undirected search the extraction procedure cannot be directed to a given substance but must be a general procedure where a compromise must be reached in that the substances

  3. Comparison of simultaneous distillation extraction and solid-phase micro-extraction for determination of volatile constituents in tobacco flavor

    Institute of Scientific and Technical Information of China (English)

    ZHONG Ke-jun; WEI Wan-zhi; GUO Fang-qiu; HUANG Lan-fang

    2005-01-01

    The volatile and semi-volatile components in tobacco flavor additives were extracted by both simultaneous distillation extraction and solid-phase micro-extraction. Extraction conditions for solid-phase micro-extraction were optimized with information theory. Then, detection were accomplished by gas chromatography-mass spectrometry. Characteristic of each method was compared. Qualitative analysis and quantitative analysis of 6# tobacco flavor sample were accomplished through both simultaneous distillation extraction and solid-phase micro-extraction. The experimental results show that solid-phase micro-extraction method is the first choice for qualitative analysis and simultaneous distillation extraction is another good selection for quantitative analysis. By means of simultaneous distillation extraction, 20 components are identified, accounting for 92.77% of the total peak areas. Through solid-phase micro-extraction, there are 17 components identified accounting for 91.49% of the total peak areas. The main aromatic components in 6# tobacco flavor sample are propanoic acid, 2-hydroxy-, ethyl ester, menthol and menthyl acetate. The presented method has been successfully used for quality control of tobacco flavor.

  4. Preparation of Plutonium Counting Source Using Solid Phase Extraction Disk

    Institute of Scientific and Technical Information of China (English)

    SUN; Hong-qing; YANG; Su-liang; DING; You-qian; YANG; Jin-ling; MAO; Guo-shu

    2013-01-01

    For the determination of trace amount of plutonium,Pu(Ⅳ)may be extracted from dilute nitric acid by TTA-xylene,and stripped by concentrated nitric acid.But the small volume of strip solution used in traditional counting source preparation by direct evaporation could lead to a rather high detection limit.Plutonium in strip solution may all be absorbed on the surface of an anion exchange resin disk.And

  5. Extraction of Pb2+ using Silica from Rice Husks Ash (RHA – Chitosan as Solid Phase

    Directory of Open Access Journals (Sweden)

    Hanandayu Widwiastuti

    2013-03-01

    Full Text Available The existence of lead (Pb compounds in waters can be caused of waste pollution from industrial activities such as dye and battery industries. Lead has toxic characteristic and is able to causing deseases. The levels of Cr(VI can be decreased by methods such as electroplating, oxidation, reduction, and membrane separation. But this methods require high cost and produce a lot of waste. Furthermore, those methods cannot determine the small concentration of Pb2+. Therefore, solid phase extraction is used because it’s a simple method and can be used to preconcentrate Pb2+ ion. The aim of this study is to create solid phase from nature material as an alternative method to determine Pb2+ in water samples. The solid phase is silica from rice husks ash (RHA that was modified using chitosan. To achieve that aim, the optimization of silica : chitosan composition was done. The influence of Pb2+ concentration and citric acid concentration was studied to obtain optimum recovery of Pb2+. Interaction between Pb2+ ion and solid phase silica – chitosan could be estimated based on the result. The result showed the optimum composition of silica : chitosan is 65% silica : 35% chitosan with Cation Exchange Capacity (CEC 0.00455 mek/g. Mass Adsorbed Pb2+for 1 g silica : chitosan 65% is 9.715 mg/g. Optimum recovery of Pb2+ on solid phase extraction is reached at concentration of Pb2+ 10 ppm and citric acid concentration 0.05 M (88.25 % and 81.18 %. This result showed that solid phase extraction using silica – chitosan can be used as an alternative method to determine Pb2+ in water.

  6. Role of Hansen solubility parameters in solid phase extraction.

    Science.gov (United States)

    Bielicka-Daszkiewicz, K; Voelkel, A; Pietrzyńska, M; Héberger, K

    2010-08-27

    The sorbent-eluent systems combined from eight polymeric sorbents and seven solvents as eluents were used for the extraction of phenol and its oxidation products from water samples. The individual interactions between sorbents, eluents and analytes were characterized by Hansen solubility parameters. Principal components analysis (PCA) was used for revealing the dominant interactions (dispersive, polar, and hydrogen bonding type) in sorbent-analyte-eluent systems. The importance of solubility parameters was also determined by a novel procedure based on sum of ranking differences (SRD). Although PCA and ranking by SRD are based on different principles and calculations, they have provided very similar results. The recovery in a given system has been predicted from the magnitudes of mutual interactions (sorbent-analyte, sorbent-eluent, analyte-eluent) by multiple linear regression.

  7. Using a new ligand for solid phase extraction of mercury

    Energy Technology Data Exchange (ETDEWEB)

    Soleimani, Majid, E-mail: m-soleimani@hotmail.com [Department of Chemistry, Faculty of Sciences, Imam Khomeini International University (IKIU), Qazvin (Iran, Islamic Republic of); Mahmodi, Mohamad Saleh [Department of Chemistry, Faculty of Sciences, Imam Khomeini International University (IKIU), Qazvin (Iran, Islamic Republic of); Morsali, Ali [Department of Chemistry, Faculty of Sciences, Tarbiat Modares University, Tehran (Iran, Islamic Republic of); Khani, Azam; Afshar, Majid Ghahraman [Department of Chemistry, Faculty of Sciences, Imam Khomeini International University (IKIU), Qazvin (Iran, Islamic Republic of)

    2011-05-15

    The octadecyl silica cartridge as a sorbent and 4-bpdb (1,4-bis(4-pyridyl)-2,3-diaza-1,3-butadiene) as a ligand is a simple, rapid and reliable method for extracting and preconcentrating of Hg(II) in real samples prior to cold vapor atomic absorption spectrometry. Sample solutions were passed through a column at pH 4.5 then retained mercury ions on the column were eluted with minimal amount of 0.01 M nitric acid with 3 mL min{sup -1} flow rate. The effect of pH, type of buffer, flow rate of sample and eluent, type and volume of the eluent were investigated and optimized. At optimum effective parameters, concentration factor and detection limit were achieved 128 and 1.87 ng L{sup -1}, respectively.

  8. Solid Phase Extraction: Applications to the Chromatographic Analysis of Vegetable Oils and Fats

    Energy Technology Data Exchange (ETDEWEB)

    Panagiotopoulout, P. M.; Tsimidou, M.

    2002-07-01

    Applications of solid-phase extraction for the isolation of certain lipid classes prior to chromatographic analysis are given. More information was found for sterols and related compounds, polar phenols and contaminants such as polycyclic aromatic hydrocarbons. Detailed analytical protocols are presented and discussed in many cases. (Author) 120 refs.

  9. Micro versus macro solid phase extraction for monitoring water contaminants: a preliminary study using trihalomethanes.

    Science.gov (United States)

    Alexandrou, Lydon D; Spencer, Michelle J S; Morrison, Paul D; Meehan, Barry J; Jones, Oliver A H

    2015-04-15

    Solid phase extraction is one of the most commonly used pre-concentration and cleanup steps in environmental science. However, traditional methods need electrically powered pumps, can use large volumes of solvent (if multiple samples are run), and require several hours to filter a sample. Additionally, if the cartridge is open to the air volatile compounds may be lost and sample integrity compromised. In contrast, micro cartridge based solid phase extraction can be completed in less than 2 min by hand, uses only microlitres of solvent and provides comparable concentration factors to established methods. It is also an enclosed system so volatile components are not lost. The sample can also be eluted directly into a detector (e.g. a mass spectrometer) if required. However, the technology is new and has not been much used for environmental analysis. In this study we compare traditional (macro) and the new micro solid phase extraction for the analysis of four common volatile trihalomethanes (trichloromethane, bromodichloromethane, dibromochloromethane and tribromomethane). The results demonstrate that micro solid phase extraction is faster and cheaper than traditional methods with similar recovery rates for the target compounds. This method shows potential for further development in a range of applications.

  10. Development of a Solid Phase Extraction Method for Agricultural Pesticides in Large-Volume Water Samples

    Science.gov (United States)

    An analytical method using solid phase extraction (SPE) and analysis by gas chromatography/mass spectrometry (GC/MS) was developed for the trace determination of a variety of agricultural pesticides and selected transformation products in large-volume high-elevation lake water sa...

  11. Solid-phase micro-extraction in bioanalysis, exemplified by lidocaine determination

    NARCIS (Netherlands)

    de Jong, GJ; Koster, EHM

    2000-01-01

    Solid-phase micro-extraction (SPME) is a never sample preparation technique that can be used for gaseous, liquid or solid samples in conjunction with GC, HPLC or CE (e.g. [1]). The use of SPME for the analysis of drugs in biofluids is also becoming popular (e.g. [2]). The principle is that a fused s

  12. Silica-Based Solid Phase Extraction of DNA on a Microchip

    Institute of Scientific and Technical Information of China (English)

    陈晓芳; 沈科跃; 刘鹏; 郭旻; 程京; 周玉祥

    2004-01-01

    Micro total analysis systems for chemical and biological analysis have attracted much attention.However,microchips for sample preparation and especially DNA purification are still underdeveloped.This work describes a solid phase extraction chip for purifying DNA from biological samples based on the adsorption of DNA on bare silica beads prepacked in a microchannel.The chip was fabricated with poly-dimethylsiloxane.The silica beads were packed in the channel on the chip with a tapered microchannel to form the packed bed.Fluorescence detection was used to evaluate the DNA adsorbing efficiency of the solid phase.The polymerase chain reaction was used to evaluate the quality of the purified DNA for further use.The extraction efficiency for the DNA extraction chip is approximately 50% with a 150-nL extraction volume.Successful amplification of DNA extracted from human whole blood indicates that this method is compatible with the polymerase chain reaction.

  13. Solid-phase extraction of antioxidant compounds from commercial cranberry extract and its antiradical activity

    Directory of Open Access Journals (Sweden)

    Tumbas Vesna T.

    2007-01-01

    Full Text Available This study is concerned with the fractionation and determination of major antioxidant compounds (phenols, flavonoids, anthocyanins and vitamin C in commercial cranberry extract. The total content of phenolics, flavonoids and total and monomers of anthocyanins, determined spectrophotometrically, was 1.67 mg/g, 0.41 mg/g, 5.12 mg/g and 3.32 mg/g. The content of vitamin C, determined volumetrically, was 121.74 mg/g. Commercial cranberry extract was dissolved in 80 % acetone and the solution was fractionated using solid phase extraction (SPE in order to abstract vitamin C, neutral and acidic phenols. The free radical scavenging activity of the cranberry extract and its fractions was investigated on stable 2,2-diphenyl-1-picrylhydrazyl (DPPH and reactive hydroxyl radicals employing electron spin resonance (ESR spectroscopy. The most effective fractions were those containing vitamin C (AADPPH= AAOH=100%, neutral (AADPPH=89.50% and AAOH=43.11% and acidic (AADPPH=83.98% and AAOH=38.58% phenols. The presence of vitamin C, abstracted from cranberry extract, was determined by Fe(III-mediated ascorbate oxidation which yields characteristic ESR doublet spectrum of ascorbyl radical.

  14. Automated Analysis of Oxytocin by On-Line in-Tube Solid-Phase Microextraction Coupled with Liquid Chromatography-Tandem Mass Spectrometry

    Directory of Open Access Journals (Sweden)

    Eri Moriyama

    2015-06-01

    Full Text Available A simple and sensitive method for the analysis of oxytocin was developed using automated on-line in-tube solid-phase microextraction (SPME coupled with liquid chromatography-tandem mass spectrometry (LC–MS/MS. Oxytocin was separated within 3 min on a Zorbax Eclipse XDB-C8 column, with water/methanol (10/90, v/v as the mobile phase at a flow rate of 0.2 mL min−1. Electrospray ionization conditions in the positive ion mode were optimized for MS/MS detection by multiple reaction monitoring. The optimum in-tube SPME conditions were 20 draw/eject cycles of 40 µL sample at a flow rate of 250 µL min−1 using a Supel-Q PLOT capillary column as an extraction device. The extracted oxytocin was easily desorbed from the capillary by passage of the mobile phase, and no carryover was observed. The calibration curves for oxytocin were linear (r = 0.9981 in the range of 0−5.0 ng mL−1, and the relative standard deviations at each point were below 14.7% (n = 3. The limit of detection of this method was 4.0 pg mL−1, and its sensitivity was 58-fold higher than that of the direct injection method. This method was applied successfully to the analysis of oxytocin in saliva samples without any other interference peaks.

  15. Analysis of heterocyclic amines in hair by on-line in-tube solid-phase microextraction coupled with liquid chromatography−tandem mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Kataoka, Hiroyuki, E-mail: hkataoka@shujitsu.ac.jp; Inoue, Tsutomu; Saito, Keita; Kato, Hisato; Masuda, Kazufumi

    2013-07-05

    Graphical abstract: Mutagenic and carcinogenic heterocyclic amines are accumulated in the hair of smoker. -- Highlights: •On-line in-tube solid-phase microextraction of heterocyclic amines was optimized. •Fourteen heterocyclic amines were simultaneously determined by LC–MS/MS. •Pico gram levels of heterocyclic amines could be easily analyzed within 15 min. •Heterocyclic amines could be quantitatively analyzed from several milligrams of hair. •The method is useful for the assessment of long-term exposure to heterocyclic amines. -- Abstract: Mutagenic and carcinogenic heterocyclic amines (HCAs) are formed during heating of various proteinaceous foods, but human exposure to HCAs has not yet been elucidated in detail. To assess long-term exposure to HCAs, we developed a simple and sensitive method for measuring HCAs in hair by automated on-line in-tube solid-phase microextraction (SPME) coupled with liquid chromatography–tandem mass spectrometry (LC–MS/MS). Using a Zorbax Eclipse XDB-C8 column, 16 HCAs were analyzed within 15 min. The optimum in-tube SPME conditions were 20 draw/eject cycles of 40 μL sample at a flow rate of 200 μL min{sup −1} using a Supel-Q PLOT capillary column as an extraction device. The extracted HCAs were easily desorbed from the column by passage of the mobile phase, with no carryover observed. This in-tube SPME LC–MS/MS method showed good linearity for HCAs in the range of 10–2000 pg mL{sup −1}, with correlation coefficients above 0.9989 (n = 18), using stable isotope-labeled HCA internal standards. The detection limits (S/N = 3) of 14 HCAs except for MeAαC and Glu-P-1 were 0.10–0.79 pg mL{sup −1}. This method was successfully utilized to analyze 14 HCAs in hair samples without any interference peaks, with quantitative limits (S/N = 10) of about 0.17–1.32 pg mg{sup −1} hair. Using this method, we evaluated the exposure to HCAs in cigarette smoke and the suitability of using hair HCAs as exposure biomarkers.

  16. Soxhlet-assisted matrix solid phase dispersion to extract flavonoids from rape (Brassica campestris) bee pollen.

    Science.gov (United States)

    Ma, Shuangqin; Tu, Xijuan; Dong, Jiangtao; Long, Peng; Yang, Wenchao; Miao, Xiaoqing; Chen, Wenbin; Wu, Zhenhong

    2015-11-15

    Soxhlet-assisted matrix solid phase dispersion (SA-MSPD) method was developed to extract flavonoids from rape (Brassica campestris) bee pollen. Extraction parameters including the extraction solvent, the extraction time, and the solid support conditions were investigated and optimized. The best extraction yields were obtained using ethanol as the extraction solvent, silica gel as the solid support with 1:2 samples to solid support ratio, and the extraction time of one hour. Comparing with the conventional solvent extraction and Soxhlet method, our results show that SA-MSPD method is a more effective technique with clean-up ability. In the test of six different samples of rape bee pollen, the extracted content of flavonoids was close to 10mg/g. The present work provided a simple and effective method for extracting flavonoids from rape bee pollen, and it could be applied in the studies of other kinds of bee pollen.

  17. The isolation of soyasaponins by fractional precipitation, solid phase extraction, and low pressure liquid chromatography.

    Science.gov (United States)

    Gurfinkel, D M; Reynolds, W F; Rao, A V

    2005-11-01

    Bioactive soyasaponins are present in soybean (Glycine max). In this study, the isolation of soyasaponins in relatively pure form (>80%) using precipitation, solid phase extraction and reverse phase low pressure liquid chromatography (RP-LPLC) is described. Soy flour soyasaponins were separated from non-saponins by methanol extraction and precipitation with ammonium sulphate. Acetylated group A soyasaponins were isolated first by solid phase extraction followed by RP-LPLC (solvent: ethanol-water). Soyasaponins, from a commercial preparation, were saponified and fractionated into deacetylated group A and group B soyasaponins by solid phase extraction (methanol-water). Partial hydrolysis of group B soyasaponins produced a mixture of soyasaponin III and soyasapogenol B monoglucuronide. RP-LPLC of deacetylated group A soyasaponins separated soyasaponin A1 and A2 (38% methanol); of group B soyasaponins isolated soyasaponin I (50% ethanol); and of the partial hydrolysate separated soyasaponin III from soyasapogenol B monoglucuronide (50% ethanol). This methodology provides soyasaponin fractions that are suitable for biological evaluation.

  18. A New Molecularly Imprinted Polymer for Solid-phase Extraction of Cotinine from Human Urine

    Institute of Scientific and Technical Information of China (English)

    Jun YANG; Xiao Lan ZHU; Ji Bao CAI; Qing De SU; Yun GAO; Liang ZHANG

    2005-01-01

    A molecularly imprinted polymer (MIP), prepared around a cotinine template, has been synthesized. The feasibility of using the polymer for solid-phase extraction (SPE) of cotinine from biological samples has been investigated. The results show that cotinine can be quantitatively retained and eluted from the polymer. Experiments with human urine samples indicate that clean target analyte is obtained for HPLC with UV detection using the protocol.

  19. HPLC WITH SOLID PHASE EXTRACTION FOR IDENTIFICATION AND DIAGNOSIS OF ORGANOPHOSPHOROUS POISONING IN GOATS

    Directory of Open Access Journals (Sweden)

    S. Manna

    2014-12-01

    Full Text Available High performance liquid chromatographic determination of organophosphorous compound has been done by reverse phase chromatography in goats. The goats were dying showing the symptoms of organophosphorous poisoning. The viscera and stomach contents sample were received from Project Co-Ordinator, Animal Disease Research Institute, Phulnakhara, Cuttack, Orissa. The analysis of samples by HPLC with UV detector after cleaning up in Solid Phase Extraction (SPE revealed presence of malathion that was later quantified.

  20. Solid-phase extraction and HPLC assay of nicotine and cotinine in plasma and brain.

    Science.gov (United States)

    Dawson, Ralph; Messina, S M; Stokes, C; Salyani, S; Alcalay, N; De Fiebre, N C; De Fiebre, C M

    2002-01-01

    The aim of this study was to develop a simple and reliable assay for nicotine (NIC) and its major metabolite, cotinine (COT), in plasma and brain. A method was developed that uses an extraction method compatible with reverse-phase high-performance liquid chromatography (HPLC) separation and ultraviolet (UV) detection. Sequential solid-phase extraction on silica columns followed by extraction using octadecyl (C18) columns resulted in mean percent recovery (n = 5) of 51 +/- 5, 64 +/- 10, and 52 +/- 10% for NIC, COT, and phenylimidazole (PI), respectively, in spiked 1-mL serum samples. Recovery (mean +/- SEM) of the internal standard (PI) from spiked samples of nicotine-injected rats averaged 64.1 +/- 1.5% (n = 138) from plasma, and 20.7+/-0.8% (n = 128) from brain. The limits of detection of NIC in plasma samples were approximately 8 ng per mL, and of COT, 13.6 ng per mL. Further optimization of our extraction method, using slower flow rates and solid-phase extraction on silica columns, followed by C18 column extraction, yielded somewhat better recoveries (38 +/-3%) for 1-mL brain homogenates. Interassay precision (coefficient of variation) was determined on the basis of daily calibrations for 2 months and was found to be 7%, 9%, and 9% for NIC, COT, and PI, respectively, whereas intra-assay variability was 3.9% for both NIC and COT. Limited studies were performed on analytical columns for comparison of retention, resolution, asymmetry, and column capacity. We concluded that a simple two-step solid-phase extraction method, coupled with HPLC separation and UV detection, can be used routinely to measure NIC and COT in biological fluids and tissues.

  1. Molecularly imprinted polymer microspheres for solid-phase extraction of protocatechuic acid in Rhizoma homalomenae.

    Science.gov (United States)

    Chen, Fang-Fang; Wang, Guo-Ying; Shi, Yan-Ping

    2011-10-01

    Molecularly imprinted polymers (MIPs) had been prepared by precipitation polymerization method using acrylamide as the functional monomer, ethylene glycol dimethacrylate as the cross-linker, acetonitrile as the porogen solvent and protocatechuic acid (PA), one of phenolic acids, as the template molecule. The MIPs were characterized by scanning electron microscopy and Fourier transform infrared, and their performance relative to non-imprinted polymers was assessed by equilibrium binding experiments. Six structurally similar phenolic acids, including p-hydroxybenzoic acid, gallic acid, salicylic acid, syringic acid, vanillic acid, ferulic acid were selected to assess the selectivity and recognition capability of the MIPs. The MIPs were applied to extract PA from the traditional Chinese medicines as a solid-phase extraction sorbent. The resultant cartridge showed that the MIPs have a good extraction performance and were able to selectively extract almost 82% of PA from the extract of Rhizoma homalomenae. Thus, the proposed molecularly imprinted-solid phase extraction-high performance liquid chromatography method can be successfully used to extract and analyse PA in traditional Chinese medicines.

  2. Selective Solid-phase Extraction of Aloe Emodin from Aloe by Molecularly Imprinted Polymers

    Institute of Scientific and Technical Information of China (English)

    TIAN Ming-lei; LEE Yu-ri; PARK Dong-wha; ROW Kyung-ho

    2013-01-01

    The extraction and separation of aloe emodin were optimized via selective molecularly imprinted solid-phase extraction.Molecularly imprinted polymer was prepared from the functional monomer,methacrylic acid and a mixture of ethanol/dodecanol(90/10,volume ratio) as porogen.It overcomes the common problems of imprinting biological polar compounds and shows high selectivity compared favorably with those of non-imprinted polymer and commercially available C18 and silica cartridges in similar aloe emodin tests.Good linearity was obtained between 0.002 and 2.5 mg/mL(r2=0.998) with relative standard deviations below 3.3%.

  3. Reducing the sulfur-dioxide binding power of sweet white wines by solid-phase extraction.

    Science.gov (United States)

    Saidane, Dorra; Barbe, Jean-Christophe; Birot, Marc; Deleuze, Hervé

    2013-11-01

    The high sulfur-dioxide binding power of sweet white wines may be reduced by extracting the naturally present carbonyl compounds from wine that are responsible for carbonyl bisulphites formation. The carbonyl compounds mainly responsible for trapping SO2 are acetaldehyde, pyruvic acid, and 2-oxoglutaric acid. The method employed was selective solid phase extraction, using phenylsulfonylhydrazine as a scavenging agent. The scavenging function was grafted onto a support prepared from raw materials derived from lignin. This approach is more acceptable to winemakers than the polymer media previously reported, as it reduces the possible contamination of wine to molecules already present in the wine making process.

  4. Molecularly imprinted sol-gel nanofibers based solid phase microextraction coupled on-line with high performance liquid chromatography for selective determination of acesulfame.

    Science.gov (United States)

    Moein, Mohammad Mahdi; Javanbakht, Mehran; Karimi, Mohammad; Akbari-adergani, Behrouz

    2015-03-01

    Sol-gel based molecularly imprinted polymer (MIP) nanofiber was successfully fabricated by electrospinning technique on the surface of a stainless steel bar. The manufactured tool was applied for on-line selective solid phase microextraction (SPME) and determination of acesulfame (ACF) as an artificial sweetener with high performance liquid chromatography (HPLC). The selective ability of method for the extraction of ACF was investigated in the presence of some selected sweeteners such as saccharine (SCH), aspartame (ASP) and caffeine (CAF). Electrospinning of MIP sol-gel solution on the stainless steel bar provided an unbreakable sorbent with high thermal, mechanical, and chemical stability. Moreover, application of the MIP-SPME tool revealed a unique approach for the selective microextraction of the analyte in beverage samples. In this work, 3-(triethoxysilyl)-propylamine (TMSPA) was chosen as a precursor due to its ability to imprint the analyte by hydrogen bonding, Van der Walls, and dipole-dipole interactions. Nylon 6 was also added as a backbone and support for the precursor in which sol could greatly growth during the sol-gel process and makes the solution electrospinable. Various effective parameters in the extraction efficiency of the MIP-SPME tool such as loading time, flow rate, desorption time, selectivity, and the sample volume were evaluated. The linearity for the ACF in beverage sample was in the range of 0.78-100.5 ng mL(-1). Limit of detection (LOD) and quantification (LOQ) were 0.23 and 0.78 ng mL(-1) respectively. The RSD values (n=5) were all below 3.5%at the 20 ng mL(-1) level.

  5. Liquid-phase extraction coupled with metal-organic frameworks-based dispersive solid phase extraction of herbicides in peanuts.

    Science.gov (United States)

    Li, Na; Wang, Zhibing; Zhang, Liyuan; Nian, Li; Lei, Lei; Yang, Xiao; Zhang, Hanqi; Yu, Aimin

    2014-10-01

    Liquid-phase extraction coupled with metal-organic frameworks-based dispersive solid phase extraction was developed and applied to the extraction of pesticides in high fatty matrices. The herbicides were ultrasonically extracted from peanut using ethyl acetate as extraction solvent. The separation of the analytes from a large amount of co-extractive fat was achieved by dispersive solid-phase extraction using MIL-101(Cr) as sorbent. In this step, the analytes were adsorbed on MIL-101(Cr) and the fat remained in bulk. The herbicides were separated and determined by high-performance liquid chromatography. The experimental parameters, including type and volume of extraction solvent, ultrasonication time, volume of hexane and eluting solvent, amount of MIL-101(Cr) and dispersive solid phase extraction time, were optimized. The limits of detection for herbicides range from 0.98 to 1.9 μg/kg. The recoveries of the herbicides are in the range of 89.5-102.7% and relative standard deviations are equal or lower than 7.0%. The proposed method is simple, effective and suitable for treatment of the samples containing high content of fat.

  6. Determination of 18 Organic Phosphorus and Pyrthroid Pesticides in Dried Vegetables using Solid-phase Extraction and On-line Gel Permeation Chromatography-GC/MS%固相萃取-在线凝胶渗透色谱-气相色谱质谱联用测定蔬菜干制品中的18种有机磷和拟除虫菊酯残留

    Institute of Scientific and Technical Information of China (English)

    薛丽; 钟艳梅

    2012-01-01

    建立了蔬菜干制品中18种有机磷农药和拟除虫菊酯农药残留的在线凝胶渗透色谱-气相色谱/质谱(GPC-GC/MS)分析方法.样品以乙腈为提取剂超声波高速匀浆提取,提取液经ENVI-Carb固相萃取柱净化,除去样品中大部分的色素等干扰基质,再经在线GPC进一步净化除去大分子干扰物质,有效降低了样品基质带来的背景干扰.采用外标法定量,在质量浓度为0.02 mg/kg~0.5mg/kg有良好的线性关系,加标水平为0.4 mg/kg时,18种农药的回收率基本都在80%~130%,相对标准偏差小于10%,检出限为0.001mg/kg~0.026 mg/kg.经实验证明,该方法是一种快速,准确,灵敏度高的同时检测梅菜干中多种农药残留的检测方法.%An on-line gel permeation chromatography-GC/MS analytical method was developed for the determination of 18 organic phosphorus pesticide and pyrethroid pesticides in dried vegetables.The samples were extracted with acetonitrile by means of ultrasonic high-speed homogenization, cleaned up by an ENVI-Carb solid phase extraction column to remove pigment in the sample and analyzed by on-line gel permeation chromatography-GC/MS. All the compounds demonstrated good linear relationship in the range of 0.02-0.5 mg/kg. The recoveries for the most of pestive standards of 0.4 mg/kg were 80%-130% and the relative standard deviations were less than 10%. The limits of detection were from 0.001 mg/kg to 0.026 mg/kg. The method was rapid, accurate and highly sensitive, which can be used for the simultaneous determination of pesticide residues in dried vegetables.

  7. Preconcentration of indapamide from human urine using molecularly imprinted solid-phase extraction.

    Science.gov (United States)

    Yılmaz, Hüma; Basan, Hasan

    2015-09-01

    A simple, sensitive, and selective molecularly imprinted solid-phase extraction and spectrophotometric method has been developed for the clean-up and preconcentration of indapamide from human urine. Molecularly imprinted polymers were prepared by a non-covalent imprinting approach using indapamide as a template molecule, 2-(trifluoromethyl) acrylic acid as a functional monomer, ethylene glycol dimethacrylate as a crosslinker, N,N-azobisisobutyronitrile as a thermal initiator and acetonitrile as a porogenic solvent. A non-imprinted polymer was also prepared in the same way, but in the absence of template. Molecularly imprinted polymer and non-imprinted polymer sorbents were dry-packed into solid-phase extraction cartridges. Eluates from cartridges were analyzed using a spectrophotometer for the determination of indapamide by referring to the calibration curve in the range 0.14-1.50 μg/mL. Preconcentration factor, limit of detection, and limit of quantification were 16.30, 0.025 μg/mL, and 0.075 μg/mL, respectively. A relatively high imprinting factor (9.3) was also achieved and recovery values for the indapamide spiked into human urine were in the range of 80.1-81.2%. In addition, relatively low within-day (0.17-0.42%) and between-day (1.1-1.4%) precision values were obtained as well. The proposed molecularly imprinted solid-phase extraction and spectrophotometric method was successfully applied to selective extraction, preconcentration, and determination of indapamide from human urine samples.

  8. Halogen bonding: A new retention mechanism for the solid phase extraction of perfluorinated iodoalkanes

    Energy Technology Data Exchange (ETDEWEB)

    Yan Xiaoqing; Shen Qianjin; Zhao Xiaoran; Gao Haiyue; Pang Xue [College of Chemistry, Beijing Normal University, Beijing 100875 (China); Jin Weijun, E-mail: wjjin@bnu.edu.cn [College of Chemistry, Beijing Normal University, Beijing 100875 (China)

    2012-11-13

    Highlights: Black-Right-Pointing-Pointer Halogen bonding (XB) is firstly utilised in solid phase extraction. Black-Right-Pointing-Pointer The perfluorinated iodine alkanes can be extracted by C-I Midline-Horizontal-Ellipsis Cl{sup -} halogen bonding. Black-Right-Pointing-Pointer The C-I Midline-Horizontal-Ellipsis Cl{sup -} halogen bond is well characterised by spectroscopy methods. Black-Right-Pointing-Pointer The analytes with strong halogen-bonding abilities can be selectively extracted. - Abstract: For the first time, halogen-bonding interaction is utilised in the solid phase extraction of perfluorinated iodoalkane (PFI). Nine PFIs, as model analytes, were tested, and analyses by UV, {sup 19}F NMR and Raman spectroscopies demonstrate that the PFIs are extracted by a strong anion exchange (SAX) sorbent from n-hexane due to the C-I Midline-Horizontal-Ellipsis Cl{sup -} halogen-bonding interactions. The results also show that the adsorptivities of SAX for the diiodoperfluoro-alkanes (diiodo-PFIs) were much stronger than those for the perfluoroalkyl iodides (monoiodo-PFIs). Specifically, the recoveries for 1,6-diiodoperfluorohexane and 1,8-diiodoperfluorooctane were higher than 80% when 100 mL of sample spiked with a 5 ng mL{sup -1} analyte mixture was extracted. Interestingly, SAX had no adsorption for hexafluorobenzene at all, which is known to be unable to form a halogen bond with Cl{sup -}. The analytical performance of the halogen bond-based SPE-GC-MS method for the diiodo-PFIs was also examined in soil samples. The sorbent SAX enabled the selective extraction of four diiodo-PFIs successfully from soil samples. The recoveries of the diiodo-PFIs extracted from 5 g soil sample at the 100 ng g{sup -1} spike level were in the range of 73.2-93.8% except 26.8% for 1,2-diiodoperfluoroethane. The limit of detection varied from 0.02 to 0.04 ng g{sup -1} in soil samples. Overall, this work reveals the great application potential of halogen bonding in the field of solid

  9. Separation and Purification of Sulforaphane from Broccoli by Solid Phase Extraction

    Science.gov (United States)

    Han, Dandan; Row, Kyung Ho

    2011-01-01

    A simple solid-phase extraction (SPE) method for the determination of sulforaphane in broccoli has been developed. The optimal conditions were found to be use of a silica SPE cartridge, and ethyl acetate and dichloromethane as washing and eluting solvents, respectively, which could eliminate interferences originating from the broccoli matrix. The extracts were sufficiently clean to be directly injected into high-performance liquid chromatography (HPLC) for further chromatographic analysis. Good linearity was obtained from 0.05 to 200 μg/mL (r = 0.998) for sulforaphane with the relative standard deviations less than 3.6%. The mean recoveries of sulforaphane from broccoli were more than 90.8% and the detection limit (S/N = 3:1) was 0.02 μg/mL. The SPE method provides a higher yield of sulforaphane from crude extracts compared to conventional liquid-liquid extraction. PMID:21673926

  10. Separation and Purification of Sulforaphane from Broccoli by Solid Phase Extraction

    Directory of Open Access Journals (Sweden)

    Kyung Ho Row

    2011-03-01

    Full Text Available A simple solid-phase extraction (SPE method for the determination of sulforaphane in broccoli has been developed. The optimal conditions were found to be use of a silica SPE cartridge, and ethyl acetate and dichloromethane as washing and eluting solvents, respectively, which could eliminate interferences originating from the broccoli matrix. The extracts were sufficiently clean to be directly injected into high-performance liquid chromatography (HPLC for further chromatographic analysis. Good linearity was obtained from 0.05 to 200 μg/mL (r = 0.998 for sulforaphane with the relative standard deviations less than 3.6%. The mean recoveries of sulforaphane from broccoli were more than 90.8% and the detection limit (S/N = 3:1 was 0.02 μg/mL. The SPE method provides a higher yield of sulforaphane from crude extracts compared to conventional liquid-liquid extraction.

  11. SIMPLE EXTRACTION OF GAMMA-HYDROXYBUTYRATE IN HUMAN WHOLE BLOOD BY HEADSPACE SOLID-PHASE MICROEXTRACTION

    OpenAIRE

    2001-01-01

    We have developed a simple method for the extraction of gamma-hydroxybutyrate (GHB) in human whole blood using headspace solid-phase microextraction (SPME). The procedure involves the conversion of GHB to gamma-butyrolactone (GBL) with acid catalysis; gamma-valerolactone (GVL) was used as internal standard (IS). After heating a vial containing a whole blood sample with GHB and IS at 80℃ for 5 min in the presence of H3PO4 solution, a Carboxen/polydimethylsiloxane -coated fiber was exposed to t...

  12. Chromatographic Separations Using Solid-Phase Extraction Cartridges: Separation of Wine Phenolics

    Science.gov (United States)

    Brenneman, Charles A.; Ebeler, Susan E.

    1999-12-01

    We describe a simple laboratory experiment that demonstrates the principles of chromatographic separation using solid-phase extraction columns and red wine. By adjusting pH and mobile phase composition, the wine is separated into three fractions of differing polarity. The content of each fraction can be monitored by UV-vis spectroscopy. When the experiment is combined with experiments involving HPLC or GC separations, students gain a greater appreciation for and understanding of the highly automated instrumental systems currently available. In addition, they learn about the chemistry of polyphenolic compounds, which are present in many foods and beverages and which are receiving much attention for their potentially beneficial health effects.

  13. Novel nanoporous sorbent for solid-phase extraction in petroleum fingerprinting

    Science.gov (United States)

    Alayande, S. Oluwagbemiga; Hlengilizwe, Nyoni; Dare, E. Olugbenga; Msagati, Titus A. M.; Akinlabi, A. Kehinde; Aiyedun, P. O.

    2016-04-01

    Sample preparation is crucial in the analysis of petroleum and its derivatives. In this study, developing affordable sorbent for petroleum fingerprinting analysis using polymer waste such expanded polystyrene was explored. The potential of electrospun expanded polystyrene (EPS) as a sorbent for the solid-phase extraction (SPE) technique was investigated, and its efficiency was compared with commercial cartridges such as alumina, silica and alumina/silica hybrid commercial for petroleum fingerprinting analysis. The chromatograms showed that the packed electrospun EPS fibre demonstrated excellent properties for SPE applications relative to the hybrid cartridges.

  14. Solid Phase Extraction Disk Procedure to Determine 239Pu in Soils

    Directory of Open Access Journals (Sweden)

    ZHANG Ji-qiao;ZHAO Ya-ping;DING You-qian;ZHANG Sheng-dong;YANG Jin-ling

    2016-11-01

    Full Text Available 239Pu in many soil samples should be analyzed to survey radioactive pollution level in nuclear facilities and its affinity environment efficiently. In order to input the opt conditions for column experiment, the experiments of the static adsorption coefficient of 239Pu to solid phase extraction disk with different contact time, concentration of HNO3 and different temperature were carried out. The chemical procedure for the rapid separation and determination of 239Pu in soils had been formulated, which using solid phase extraction disk (EmporeTM Anion Exchange-SR as extraction material and liquid scintillation spectrometry counting as measurement. In the procedure, soil sample usage was 10 g, and were leached by 8 mol/L HNO3, the chemical recovery of the procedure was about 78.9%, and the minimum detectable concentration was 3.7 Bq/kg. It took less than 3 hours once and the presence of 137Cs, 90Sr-90Y and natural uranium, 241Am, 99Tc did not interfere with the procedure, owning high DF of them. The procedure can be used extensively in determination of 239Pu in soils.

  15. Improved detection limits for phthalates by selective solid-phase micro-extraction

    KAUST Repository

    Zia, Asif I.

    2016-03-30

    Presented research reports on an improved method and enhanced limits of detection for phthalates; a hazardous additive used in the production of plastics by solid-phase micro-extraction (SPME) polymer in comparison to molecularly imprinted solid-phase extraction (MISPE) polymer. The polymers were functionalized on an interdigital capacitive sensor for selective binding of phthalate molecules from a complex mixture of chemicals. Both polymers owned predetermined selectivity by formation of valuable molecular recognition sites for Bis (2-ethylhexyl) phthalate (DEHP). Polymers were immobilized on planar electrochemical sensor fabricated on a single crystal silicon substrate with 500 nm sputtered gold electrodes fabricated using MEMS fabrication techniques. Impedance spectra were obtained using electrochemical impedance spectroscopy (EIS) to determine sample conductance for evaluation of phthalate concentration in the spiked sample solutions with various phthalate concentrations. Experimental results revealed that the ability of SPME polymer to adsorb target molecules on the sensing surface is better than that of MISPE polymer for phthalates in the sensing system. Testing the extracted samples using high performance liquid chromatography with photodiode array detectors validated the results.

  16. Gaseous Products of Incense Coil Combustion Extracted by Passive Solid Phase Microextraction Samplers

    Directory of Open Access Journals (Sweden)

    Wen-Hsi Cheng

    2015-06-01

    Full Text Available Burning incense indoors is a common behavior in Southeast Asia. In this investigation, needle trap samplers (NTS, a novel, green analytical technology is used for sampling gaseous combustion by-products from sandalwood incense coils. To extract indoor volatile organic compounds (VOCs, two NTS are prepared, one using 60–80 mesh and the other using 100–120 mesh divinylbenzene (DVB particles packed in 22-gauge stainless steel needles. This work compares extraction efficiency of an NTS and that of a commercially available 100 μm polydimethylsiloxane solid phase microextration (PDMS-SPME fiber sampler. Experimental results indicated that the 100–120 mesh DVB-NTS performed best among all samplers during a 1 h sampling period. The main extracted compounds were toluene, ethylbenzene, propane, chloromethane, 1,3-butadiene, methanol and dichloromethane. The potential use of small badge-sized or pen-sized NTS for the indoor atmosphere and occupational hygiene applications is addressed.

  17. Comparison of solvent extraction and solid-phase extraction for the determination of polychlorinated biphenyls in transformer oil.

    Science.gov (United States)

    Mahindrakar, A N; Chandra, S; Shinde, L P

    2014-01-01

    Solid-phase extraction (SPE) of nine polychlorinated biphenyls (PCBs) from transformer oil samples was evaluated using octadecyl (CI8)-bonded porous silica. The efficiency of SPE of these PCBs was compared with those obtained by solvent extraction with DMSO and hexane. Average recoveries exceeding 95% for these PCBs were obtained via the SPE method using small cartridges containing 100mg of 40 pm CI8-bonded porous silica. The average recovery by solvent extraction with DMSO and hexane exceeded 83%. It was concluded that the recoveries and precision for the solvent extraction of PCBs were poorer than those for the SPE.

  18. Rapid solid-phase extraction and analysis of resveratrol and other polyphenols in red wine.

    Science.gov (United States)

    Hashim, Shima N N S; Schwarz, Lachlan J; Boysen, Reinhard I; Yang, Yuanzhong; Danylec, Basil; Hearn, Milton T W

    2013-10-25

    Red wine has long been credited as a good source of health-beneficial antioxidants, including the bioactive polyphenols catechin, quercetin, and (E)-resveratrol. In this paper, we report the application of reusable molecularly imprinted polymers (MIPs) for the selective and robust solid-phase extraction (SPE) and rapid analysis of (E)-resveratrol (LOD=8.87×10(-3) mg/L, LOQ=2.94×10(-2) mg/L), along with a range of other polyphenols from an Australian Pinot noir red wine. Optimization of the molecularly imprinted solid-phase extraction (MISPE) protocol resulted in the significant enrichment of (E)-resveratrol and several structurally related polyphenols. These secondary metabolites were subsequently identified by RP-HPLC and μLC-ESI ion trap MS/MS methods. The developed MISPE protocol employed low volumes of environmentally benign solvents selected according to the Green Chemistry principles, and resulted in the recovery of 99% of the total (E)-resveratrol present. These results further demonstrate the potential of generic protocols for the analysis of target compound with health beneficial properties within the food and nutraceutical industries using tailor-made MIPs.

  19. Solid phase extraction and spectrophotometric determination of palladium with 2-(2-quinolylazo-5-diethylaminobenzoic acid

    Directory of Open Access Journals (Sweden)

    WEIZU YANG

    2006-07-01

    Full Text Available Asensitive, selective and rapid method for the determination of palladium based on the rapid reaction of palladium(II with 2-(2-quinolylazo-5-diethylaminobenzoic acid (QADEAB and the solid phase extraction of the Pd(II –QADEAB chelate with a reversed phase polymer-based C18 cartridge was developed. In the presence of 0.05 – 0. 5 mol/L of hydrochloric acid solution and cetyl trimethylammonium bromide (CTAB medium, QADEAB reacts with palladium(II to form a violet complex with a mole ratio 1:2 (palladium to QADEAB. The chelate was enriched by solid phase extraction with a reversed phase polymer-based C18 cartridge. An enrichment factor of 200 was obtained by elution of the chelate form the cartridge with the minimal amount of isopentyl alcohol. The molar absorptivity of the chelate in the isopentyl alcohol medium was 1.43 × 105 L mol-1 cm-1 at 628 nm. Beer’s law was obeyed in the range of 0.01 – 1.2 mg/mL. The relative standard deviation for eleven replicate samples at the 0.2 mg/L level was 2.18 %. The attained detection limit amounted to 0.02 mg/L in the original samples. This method was applied to the determination of palladium in environmental samples with good results.

  20. Novel polymeric resin for solid phase extraction and determination of lead in waters

    Energy Technology Data Exchange (ETDEWEB)

    Karaaslan, Nagihan M.; Cengiz, Emine; Yaman, Mehmet [Science Faculty, Department of Chemistry, Firat University, Elazig (Turkey); Senkal, B. Filiz [Science and Arts Faculty, Department of Chemistry, Istanbul Technical University, Istanbul (Turkey)

    2010-11-15

    Interest in preconcentration techniques for the determination of metals at ultratrace levels still continues increasingly because of some disadvantages of flameless atomic absorption spectrometry and the high costs of other sensitive methods in compared to flame atomic absorption spectrometry (FAAS). Among preconcentration techniques, solid-phase extraction is the most popular because of a number of advantages. In this work, thiol-containing sulfonamide resin was synthesized, characterized, and applied as a new sorption material for solid phase extraction and determination of lead in natural water samples. The optimization of experimental conditions was performed using the parameters including pH, contact time, and volumes of initial and elution solutions. After preconcentration procedure, FAAS was used for determinations. The synthesized resin exhibits the superiority in compared to the other adsorption reagents because of the fact that there is no necessity of any complexing reagent as well as high sorption capacity. Consequently, 280-fold improvement in the sensitivity of analytical scheme was achieved by combining the slotted tube atom trap-atomic absorption spectrometry (STAT-FAAS) and the developed preconcentration method. The limit of detection was found to be 0.15 ng mL{sup -1}. The Pb{sup 2+} concentrations in the studied water samples were found to be in the range of 0.9-6.7 ng mL{sup -1}. (Copyright copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  1. Hydrophilic solid-phase extraction of melamine with ampholine-modified hybrid organic-inorganic silica material.

    Science.gov (United States)

    Wang, Tingting; Zhu, Yiming; Ma, Junfeng; Xuan, Rongrong; Gao, Haoqi; Liang, Zhen; Zhang, Lihua; Zhang, Yukui

    2015-01-01

    In this work, an ampholine-functionalized hybrid organic-inorganic silica sorbent was successfully used to extract melamine from a milk formula sample by a hydrophilic interaction solid-phase extraction protocol. Primary factors affecting the extraction efficiency of the material such as extraction solvent, elution solvent, sample loading volume, and elution volume have been thoroughly optimized. Under the optimized hydrophilic solid-phase extraction conditions, the recoveries of melamine spiked in milk formula samples ranged from 86.2 to 101.8% with relative standard deviations of 4.1-9.4% (n = 3). The limit of detection (S/N = 3) was 0.32 μg/g. The adsorption capacity toward melamine was 30 μg of melamine per grams of sorbent. Due to its simplicity, rapidity and cost effectiveness, the newly developed hydrophilic solid-phase extraction method should provide a promising tool for daily monitoring of doped melamine in milk formula.

  2. Evaluation of single-walled carbon nanohorns as sorbent in dispersive micro solid-phase extraction

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez-Soto, Juan Manuel; Cardenas, Soledad [Department of Analytical Chemistry, Institute of Fine Chemistry and Nanochemistry, Marie Curie Building, Campus de Rabanales, University of Cordoba, 14071 Cordoba (Spain); Valcarcel, Miguel, E-mail: qa1meobj@uco.es [Department of Analytical Chemistry, Institute of Fine Chemistry and Nanochemistry, Marie Curie Building, Campus de Rabanales, University of Cordoba, 14071 Cordoba (Spain)

    2012-02-10

    Highlights: Black-Right-Pointing-Pointer The potential of single walled carbon nanohorns in dispersive solid phase microextraction has been evaluated. Black-Right-Pointing-Pointer The method was characterized for the extraction of PAHs from waters. Black-Right-Pointing-Pointer Single walled carbon nanohorns were better extractant than carbon nanotubes and carbon nanocones. Black-Right-Pointing-Pointer The limits of detection were adequate for the target analytes in environmental waters. - Abstract: A new dispersive micro solid-phase extraction method which uses single-walled carbon nanohorns (SWNHs) as sorbent is proposed. The procedure combines the excellent sorbent properties of the nanoparticles with the efficiency of the dispersion of the material in the sample matrix. Under these conditions, the interaction with the analytes is maximized. The determination of polycyclic aromatic hydrocarbons was selected as model analytical problem. Two dispersion strategies were evaluated, being the functionalization via microwave irradiation better than the use of a surfactant. The extraction was accomplished by adding 1 mL of oxidized SWHNs (o-SWNHs) dispersion to 10 mL of water sample. After extraction, the mixture was passed through a disposable Nylon filter were the nanoparticles enriched with the PAHs were retained. The elution was carried out with 100 {mu}L of hexane. The limits of detection achieved were between 30 and 60 ng L{sup -1} with a precision (as repeatability) better than 12.5%. The recoveries obtained for the analytes in three different water samples were acceptable in all instances. The performance of o-SWNHs was favourably compared with that provided by carboxylated single-walled carbon nanotubes and thermally treated carbon nanocones.

  3. Antioxidative properties of defatted dabai pulp and peel prepared by solid phase extraction.

    Science.gov (United States)

    Khoo, Hock Eng; Azlan, Azrina; Ismail, Amin; Abas, Faridah

    2012-08-14

    Solid phase extraction (SPE) using Sep-Pak® cartridges is one of the techniques used for fractionation of antioxidant compounds in waste of dabai oil extraction (defatted dabai parts). The aim of this study was to determine the phenolic compounds and antioxidant capacity in crude extracts and several SPE fractions from methanolic extract of defatted dabai pulp and peel. Based on SPE, Sep-Pak® cyanopropyl and C₁₈ cartridges were used to fractionate the antioxidant-rich crude extracts into water and methanolic fractions. Analyzed using LC-MS, flavonoids, anthocyanins, saponin derivatives and other unknown antioxidative compounds were detected in the defatted dabai crude extracts and their SPE fractions. Anthocyanins were the major phenolic compounds identified in the defatted dabai peel and detected in most of the SPE fractions. Methanolic fractions of defatted dabai parts embraced higher total phenolics and antioxidant capacity than water fractions. This finding also revealed the crude extracts of defatted dabai peel have the most significant antioxidant properties compared to the methanolic and water fractions studied. The crude extract of defatted dabai parts remain as the most potent antioxidant as it contains mixture of flavonoids, anthocyanins and other potential antioxidants.

  4. Solid phase extraction and metabolic profiling of exudates from living copepods

    DEFF Research Database (Denmark)

    Selander, Erik; Heuschele, Jan; Nylund, Göran M.

    2016-01-01

    Copepods are ubiquitous in aquatic habitats. They exude bioactive compounds that mediate mate finding or induce defensive traits in prey organisms. However, little is known about the chemical nature of the copepod exometabolome that contributes to the chemical landscape in pelagic habitats. Here we...... describe the development of a closed loop solid phase extraction setup that allows for extraction of exuded metabolites from live copepods. We captured exudates from male and female Temora longicornis and analyzed the content with high resolution LC-MS. Chemometric methods revealed 87 compounds...... that constitute a specific chemical pattern either qualitatively or quantitatively indicating copepod presence. The majority of the compounds were present in both female and male exudates, but nine compounds were mainly or exclusively present in female exudates and hence potential pheromone candidates...

  5. Analysis of volatiles of malt whisky by solid-phase microextraction and stir bar sorptive extraction.

    Science.gov (United States)

    Demyttenaere, Jan C R; Martínez, Jorge I Sánchez; Verhé, Roland; Sandra, Pat; De Kimpe, Norbert

    2003-01-24

    Blended Scotch whisky was analysed by solid-phase microextraction (SPME) and stir bar sorptive extraction (SBSE) to study the composition of the volatiles. For SPME analysis, three different fibres were compared, poly(dimethylsiloxane) (PDMS) (100 microm). poly(acrylate) (PA) (85 microm) and divinylbenzene-Carboxen on poly(dimethylsiloxane) (DVB-CAR-(PDMS) (50/30 microm). It was found that the PDMS and DVB-CAR-PDMS fibres showed a higher enrichment capacity than PA as well as a better reproducibility. The influence of sampling time, temperature and salt addition on the enrichment of volatiles as well as the difference between liquid and headspace SPME were studied. An optimum SPME method was developed. Finally a more recent sample preparation technique, namely SBSE was evaluated to extract whisky volatiles.

  6. Combined liquid and solid-phase extraction improves quantification of brain estrogen content

    Directory of Open Access Journals (Sweden)

    Andrew eChao

    2011-09-01

    Full Text Available Accuracy in quantifying brain-derived steroid hormones (‘neurosteroids’ has become increasingly important for understanding the modulation of neuronal activity, development, and physiology. Relative to other neuroactive compounds and classical neurotransmitters, steroids pose particular challenges with regard to isolation and analysis, owing to their lipid solubility. Consequently, anatomical studies of the distribution of neurosteroids have relied primarily on the expression of neurosteroid synthesis enzymes. To evaluate the distribution of synthesis enzymes vis-à-vis the actual steroids themselves, traditional steroid quantification assays, including radioimmunoassays (RIA, have successfully employed liquid extraction methods (e.g., ether, dichloromethane or methanol to isolate steroids from microdissected brain tissue. Due to their sensitivity, safety and reliability, the use of commercial enzyme immunoassays (EIA for laboratory quantification of steroids in plasma and brain has become increasingly widespread. However, EIAs rely on enzymatic reactions in vitro, making them sensitive to interfering substances in brain tissue and thus producing unreliable results. Here, we evaluate the effectiveness of a protocol for combined, two-stage liquid/solid phase extraction as compared to conventional liquid extraction alone for the isolation of estradiol (E2 from brain tissue. We employ the songbird model system, in which brain steroid production is pronounced and linked to neural mechanisms of learning and plasticity. This study outlines a combined liquid-solid phase extraction protocol that improves the performance of a commercial EIA for the quantification of brain E2 content. We demonstrate the effectiveness of our optimized method for evaluating the region specificity of brain E2 content, compare these results to established anatomy of the estrogen synthesis enzyme and estrogen receptor, and discuss the nature of potential EIA interfering

  7. Development of a Paper Spray Mass Spectrometry Cartridge with Integrated Solid Phase Extraction for Bioanalysis.

    Science.gov (United States)

    Zhang, Chengsen; Manicke, Nicholas E

    2015-06-16

    A novel paper spray cartridge with an integrated solid phase extraction (SPE) column is described. The cartridge performs extraction and pre-concentration, as well as sample ionization by paper spray, from complex samples such as plasma. The cartridge allows for selective enrichment of target molecules from larger sample volumes and removal of the matrix, which significantly improved the signal intensity of target compounds in plasma samples by paper spray ionization. Detection limits, quantitative performance, recovery, ionization suppression, and the effects of sample volume were evaluated for five drugs: carbamazepine, atenolol, sulfamethazine, diazepam, and alprazolam. Compared with direct paper spray analysis of dried plasma spots, paper spray analysis using the integrated solid phase extraction improved the detection limits significantly by a factor of 14-70, depending on the drug. The improvement in detection limits was, in large part, due to the capability of analyzing larger sample volumes. In addition, ionization suppression was found to be lower and recovery was higher for paper spray with integrated SPE, as compared to direct paper spray analysis. By spiking an isotopically labeled internal standard into the plasma sample, a linear calibration curve for the drugs was obtained from the limit of detection (LOD) to 1 μg/mL, indicating that this method can be used for quantitative analysis. The paper spray cartridge with integrated SPE could prove valuable for analytes that ionize poorly, in applications where lower detection limits are required, or on portable mass spectrometers. The improved performance comes at the cost of requiring a more complex paper spray cartridge and requiring larger sample volumes than those used in typical direct paper spray ionization.

  8. Improved resins and novel materials and methods for solid phase extraction and high performance liquid chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Freeze, Ronald [Iowa State Univ., Ames, IA (United States)

    1997-10-08

    Solid-phase extraction (SPE) has grown to be one of the most widely used methods for isolation and preconcentration of a vast range of compounds from aqueous solutions. By modifying polymeric SPE resins with chelating functional groups, the selective uptake of metals was accomplished. The resin, along with adsorbed metals, was vaporized in the ICP and detection of the metals was then possible using either mass or emission spectroscopy. Drug analyses in biological fluids have received heightened attention as drug testing is on the increase both in sports and in the work environment. By using a direct-injection technique, biological fluids can be injected directly into the liquid chromatographic system with no pretreatment. A new surfactant, a sulfonated form of Brij-30 (Brij-S) is shown to prevent the uptake of serum proteins on commercial HPLC columns by forming a thin coating on the silica C18 surface. Excellent separations of eight or more drugs with a wide range of retention times were obtained. The separations had sharper peaks and lower retention times than similar separations performed with the surfactant sodium dodecylsulfate (SDS). Quantitative recovery of a number of drugs with limits of detection near 1 ppm with a 5 μl injection volume were obtained. Finally, a method for solid-phase extraction in a syringe is introduced. The system greatly reduced the volume of solvent required to elute adsorbed analytes from the SPE bed while providing a semi-automated setup. SPE in a syringe consists of a very small bed of resin-loaded membrane packed into a GC or HPLC syringe. After extraction, elution was performed with just a few μl of solvent. This small elution volume allowed injection of the eluent directly from the syringe into the chromatographic system, eliminating the handling problems associated with such small volumes.

  9. Suitability of microwave-assisted extraction coupled with solid-phase extraction for organophosphorus pesticide determination in olive oil.

    Science.gov (United States)

    Fuentes, Edwar; Báez, María E; Quiñones, Adalí

    2008-10-17

    A systematic study of the microwave-assisted extraction coupled to solid-phase extraction of nine organophosphorus pesticides (dimethoate, diazinon, pirimiphos methyl, parathion methyl, malathion, fenthion, chlorpyriphos, methidathion and azinphos methyl) from olive oil is described. The method is based on microwave-assisted liquid-liquid extraction with partition of organophosphorus pesticides between an acetonitrile-dichloromethane mixture and oil. Cleanup of extracts was performed with ENVI-Carb solid-phase extraction cartridge using dichloromethane as the elution solvent. The determination of pesticides in the final extracts was carried out by gas chromatography-flame photometric detection and gas chromatography-tandem mass spectrometry, using a triple quadrupole mass analyzer, for confirmative purposes. The study and optimization of the method was achieved through experimental design where recovery of compounds using acetonitrile for partition ranged from 62 to 99%. By adding dichloromethane to the extracting solution, the recoveries of more hydrophobic compounds were significantly increased. Under optimized conditions recoveries of pesticides from oil were equal to or higher than 73%, except for fenthion and chlorpyriphos at concentrations higher than 0.06microgg(-1) and diazinon at 0.03microgg(-1), with RSDs equal to or lower than 11% and quantification limits ranging from 0.007 to 0.020microgg(-1). The proposed method was applied to residue determination of the selected pesticides in commercial olive and avocado oil produced in Chile.

  10. Development of a monolithic polymer pipette for solid-phase extraction of liquiritigenin in rat plasma

    Institute of Scientific and Technical Information of China (English)

    Hong Wu Zhang; Kang Li; Zhi Xian Liang; Feng Yang Wang; Qi Wen Lu

    2012-01-01

    A monolithic polymer column with mixed-mode interaction was prepared by in situ polymerization in a 1000 μ,L pipette.Two kinds of monomers,butyl methacrylate (BMA) and 2-(dimethylamino)ethyl methacrylate (DMAM) were applied to constructing the mixed-mode interaction of monolithic polymer column.Its solid-phase extraction properties for liquiritigenin (LQG) were evaluated by high performance liquid chromatography (HPLC) with a gradient elution procedure.After the extraction procedure was optimized,the maximum binding capacity and extraction recovery following the optimal extraction procedure were investigated.Calibration curve was expressed as A =65.9C + 4.53 (r2 =0.998) with a linear range of 0.151-1.80 μg/mL.The experimental results indicate that the monolithic polymer pipette presents good extraction efficiency for LQG.It can be envisaged that the developed monolithic polymer pipette possesses the potential for its application to the enrichment of other flavonoids compounds being siniilar to the structure of LQG.

  11. Enhanced spectrofluorimetric determination of aflatoxin M1 in liquid milk after magnetic solid phase extraction

    Science.gov (United States)

    Hashemi, Mahdi; Taherimaslak, Zohreh; Rashidi, Somayeh

    2014-07-01

    A simple and sensitive method using magnetic solid phase extraction (MSPE) followed by spectrofluorimetric detection has been developed for separation and determination of aflatoxin M1 (AFM1) in liquid milk. The method is based on the extraction of AFM1 on the modified magnetic nanoparticles (MMNPs) and subsequent derivatization of extracted AFM1 to AFM1 hemi-acetal derivative (AFM2a) by reaction with trifluoroacetic acid (TFA) for spectrofluorimetric detection. Magnetic nanoparticles (MNPs) coated by 3-(trimethoxysilyl)-1-propantiol (TMSPT) and modified with 2-amino-5-mercapto-1,3,4-thiadiazole (AMT) were used as adsorbent in MSPE procedure. Influential parameters affecting the extraction efficiency were investigated and optimized. Under the optimum conditions the calibration curve for AFM1 determination showed good linearity in the range 0.030-10.0 μg L-1 (R2 = 0.9991). The repeatability and reproducibility (RSD%) for 0.050 μg L-1 of AFM1 were 4.5% and 5.3%, respectively and limit of detection limit (S/N = 3) was estimated to be 0.010 μg L-1. The developed method was successfully applied for extraction of AFM1 from spiked liquid milk and natural contaminated liquid milk. The good spiked recoveries ranging from 91.6% to 96.1% were obtained. The results demonstrated that the developed method is simple, inexpensive, accurate and remarkably free from interference effects.

  12. Multicomutation flow system for manganese speciation by solid phase extraction and flame atomic absorption spectrometry

    Science.gov (United States)

    Tobiasz, Anna; Sołtys, Monika; Kurys, Ewa; Domagała, Karolina; Dudek-Adamska, Danuta; Walas, Stanisław

    2017-08-01

    In the paper an application of solid phase extraction technique for speciation analysis of manganese in water samples with the use of flame atomic absorption spectrometry is presented. Two types of sorbents, activated silica gel and Dowex 1 × 4, were used respectively for simultaneously Mn2 + and MnO42 - retention and preconcentration. The whole procedure was realized in multicomutation flow system. Different conditions like: type and concentration of eluent, sample pH and loading time were tested during the study. Under appropriate conditions, it was possible to obtained enrichment factors of 20 and 16 for Mn(II) and Mn(VII), respectively. Precision of the procedure was close to 4% (measured as relative standard deviation), whereas the detection limit (3σ) was 1.4 μg·L- 1 for Mn(II) and 4.8 μg·L- 1 for Mn(VII).

  13. Convenient solid phase extraction of cephalosporins in milk using a molecularly imprinted polymer.

    Science.gov (United States)

    Quesada-Molina, Carolina; Claude, Bérengère; García-Campaña, Ana M; del Olmo-Iruela, Monsalud; Morin, Philippe

    2012-11-15

    In this paper, a molecularly imprinted polymer (MIP) for cephalosporin molecules (cephalexin (CFL) and cephapirin (CFP)), was prepared by non covalent molecular imprinting approach and applied to solid phase extraction (SPE). For MIP synthesis, a tributylammonium cefadroxil salt (TBA-CFD) was used as template with methacrylic acid and ethylene glycol dimethacrylate as monomer and cross-linker, respectively, in acetone-methanol 92/8 (v/v) mixture. The selectivity of MIP versus non imprinted polymer (NIP) was confirmed for CFL, CFD and CFP in standard solutions as well as in milk samples. The efficiency of the synthesized MIP was evaluated by means of the application of the proposed MIP-SPE procedure to spiked milk samples previous to the HPLC method for the detection of cephalosporins. The MIP-SPE recoveries were higher than 60% for the three target analytes in spiked milk. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. Isolation of tetracyclines in milk using a solid-phase extracting column and water eluent.

    Science.gov (United States)

    Furusawa, Naoto

    2003-01-01

    An isolating method using a solid-phase extraction (SPE) ISOLUTE(R) C8 endcapped syringe-column for routine monitoring of residual tetracyclines (TCs) (oxytetracycline (OTC), tetracycline (TC), chlortetracycline (CTC), and doxycycline (DC)) in cow's milk is presented. In the simplest and most environmentally harmless method, milk samples could be applied directly to the SPE column, following which all TCs were eluted with water. No organic solvents were used at all. The purified sample was injected into a high-performance liquid chromatography (HPLC) with a photo-diode array detector (PDAD). For the HPLC determination/identification, a LiChrospher(R) 100 RP-8 endcapped column and a mobile phase of acetonitrile -7% (v v(-1)) acetic acid solution (in water) (35:65, v v(-1)) with a PDAD was used. The total time required for the analysis of one sample was 80 and <5%, respectively.

  15. Determination of resveratrol in red wine by solid phase extraction-flow injection chemiluminescence method

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A sensitive flow injection chemiluminescence method has been developed for the detection of resveratrol in red wine based on the fact that resveratrol can greatly enhance chemiluminescence reaction between KMnO4 and HCHO in sulfuric acid medium.Analytes were pre-concentrated on solid sorbents (C18 solid-phase extraction cartridges). Under the optimum conditions, the proposed method allows the measurement of resveratrol over the range of 1.32 × 10-s to 1.32 × 10-5 mol/L with a detection limit of 3.30 × 10-9 mol/L, and the relative standard deviation for 1.32 × 10-5 mol/L resveratrol (n = 11 ) is 3.8%. This method has been successfully applied for the determination of the resveratrol in red wine. Furthermore, the possible reaction mechanism was also discussed.

  16. Recent Developments in Solid-Phase Extraction for Near and Attenuated Total Reflection Infrared Spectroscopic Analysis

    Directory of Open Access Journals (Sweden)

    Christian W. Huck

    2016-05-01

    Full Text Available A review with more than 100 references on the principles and recent developments in the solid-phase extraction (SPE prior and for in situ near and attenuated total reflection (ATR infrared spectroscopic analysis is presented. New materials, chromatographic modalities, experimental setups and configurations are described. Their advantages for fast sample preparation for distinct classes of compounds containing different functional groups in order to enhance selectivity and sensitivity are discussed and compared. This is the first review highlighting both the fundamentals of SPE, near and ATR spectroscopy with a view to real sample applicability and routine analysis. Most of real sample analyses examples are found in environmental research, followed by food- and bioanalysis. In this contribution a comprehensive overview of the most potent SPE-NIR and SPE-ATR approaches is summarized and provided.

  17. Headspace Solid Phase Micro Extraction Gas Chromatographic Determination of Fenthion in Human Serum

    Directory of Open Access Journals (Sweden)

    Kyriaki Machera

    2008-05-01

    Full Text Available A simple and effective analytical procedure was developed for the determination of fenthion residues in human serum samples. The sample treatment was performed using the headspace solid-phase micro extraction with polyacrylate fiber, which has the advantage to require low amount of serum (1 mL without tedious pre-treatment. The quantification of fenthion was carried out by gas chromatography-mass spectrometry and the recoveries ranged from 79 to 104% at two spiking levels for 6 replicates. Detection and quantification limits were calculated as 1.51 and 4.54 ng/mL of serum respectively. Two fenthion metabolites − fenoxon and fenthion–sulfoxide − were also identified.

  18. Solid phase extraction of iron and lead in environmental matrices on amberlite xad-1180/pv

    Directory of Open Access Journals (Sweden)

    Mustafa Soylak

    2006-04-01

    Full Text Available A solid phase extraction procedure using Amberlite XAD-1180/Pyrocatechol violet (PV chelating resin for the determination of iron and lead ions in various environmental samples was established. The procedure is based on the sorption of lead(II and iron(III ions onto the resin at pH 9, followed by elution with 1 mol/L HNO3 and determination by flame atomic absorption spectrometry. The influence of alkaline, earth alkaline and some transition metals, as interferents, are discussed. The recoveries for the spiked analytes were greater than 95%. The detection limits for lead and iron by FAAS were 0.37 µg/L and 0.20 µg/L, respectively. Validation of the method described here was performed by using three certified reference materials (SRM 1515 Apple Leaves, SRM 2711 Montana Soil and NRCC-SLRS-4 Riverine Water. The procedure was successfully applied to natural waters and human hair.

  19. Molecularly imprinted solid-phase extraction for the screening of antihyperglycemic biguanides.

    Science.gov (United States)

    Feng, Sherry Y; Lai, Edward P C; Dabek-Zlotorzynska, Ewa; Sadeghi, Susan

    2004-02-20

    A new molecularly imprinted polymer (MIP) was specifically synthesized as a smart material for the recognition of metformin hydrochloride in solid-phase extraction. Particles of this MIP were packed into a stainless-steel tubing (50 mm x 0.8 mm i.d.) equipped with an exit frit. This micro-column was employed in the development of a molecularly imprinted solid-phase extraction (MISPE) method for metformin determination. The MISPE instrumentation consisted of a micrometer pump, an injector valve equipped with a 20-microl sample loop, a UV detector, and an integrator. With CH3CN as the mobile phase flowing at 0.5 ml/min, 95 +/- 2% binding could be achieved for 1200 ng of metformin from one injection of a phosphate-buffered sample solution (pH 2.5). Methanol + 3% trifluoroacetic acid was good for quantitative pulsed elution (PE) of the bound metformin. The MISPE-PE method, with UV detection at 240 nm, afforded a detection limit of 16 ng (or 0.8 microg/ml) for metformin. However, the micro-column interacted indiscriminately with phenformin with a 49 +/- 2% binding. A systematic investigation of binding selectivity was conducted with respect to sample composition (including the solvent, matrix, pH, buffer and surfactant effects). An intermediate step of differential pulsed elution used acetonitrile with 5% picric acid to remove phenformin and other structural analogues. A final pulsed elution of metformin for direct UV detection was achieved using 3% trifluoroacetic acid in methanol.

  20. Determination of colloidal and dissolved silver in water samples using colorimetric solid-phase extraction.

    Science.gov (United States)

    Hill, April A; Lipert, Robert J; Porter, Marc D

    2010-03-15

    The increase in bacterial resistance to antibiotics has led to resurgence in the use of silver as a biocidal agent in applications ranging from washing machine additives to the drinking water treatment system on the International Space Station (ISS). However, growing concerns about the possible toxicity of colloidal silver to bacteria, aquatic organisms and humans have led to recently issued regulations by the US EPA and FDA regarding the usage of silver. As part of an ongoing project, we have developed a rapid, simple method for determining total silver, both ionic (silver(I)) and colloidal, in 0.1-1mg/L aqueous samples, which spans the ISS potable water target of 0.3-0.5mg/L (total silver) and meets the US EPA limit of 0.1mg/L in drinking water. The method is based on colorimetric solid-phase extraction (C-SPE) and involves the extraction of silver(I) from water samples by passage through a solid-phase membrane impregnated with the colorimetric reagent DMABR (5-[4-(dimethylamino)benzylidene]rhodanine). Silver(I) exhaustively reacts with impregnated DMABR to form a colored compound, which is quantified using a handheld diffuse reflectance spectrophotometer. Total silver is determined by first passing the sample through a cartridge containing Oxone, which exhaustively oxidizes colloidal silver to dissolved silver(I). The method, which takes less than 2 min to complete and requires only approximately 1 mL of sample, has been validated through a series of tests, including a comparison with the ICP-MS analysis of a water sample from ISS that contained both silver(I) and colloidal silver. Potential earth-bound applications are also briefly discussed.

  1. Novel restricted access materials combined to molecularly imprinted polymers for selective solid-phase extraction of organophosphorus pesticides from honey.

    Science.gov (United States)

    He, Juan; Song, Lixin; Chen, Si; Li, Yuanyuan; Wei, Hongliang; Zhao, Dongxin; Gu, Keren; Zhang, Shusheng

    2015-11-15

    A novel restricted access materials (RAM) combined to molecularly imprinted polymers (MIPs), using malathion as template molecule and glycidilmethacrylate (GMA) as pro-hydrophilic co-monomer, were prepared for the first time. RAM-MIPs with hydrophilic external layer were characterized by scanning electron microscopy and recognition and selectivity properties were compared with the restricted access materials-non-molecularly imprinted polymers (RAM-NIPs) and unmodified MIPs. RAM-MIPs were used as the adsorbent enclosed in solid phase extraction column and several important extraction parameters were comprehensively optimized to evaluate the extraction performance. Under the optimum extraction conditions, RAM-MIPs exhibited comparable or even higher selectivity with greater extraction capacity toward six kinds of organophosphorus pesticides (including malathion, ethoprophos, phorate, terbufos, dimethoate, and fenamiphos) compared with the MIPs and commercial solid phase extraction columns. The RAM-MIPs solid phase extraction coupled with gas chromatography was successfully applied to simultaneously determine six kinds of organophosphorus pesticides from honey sample. The new established method showed good linearity in the range of 0.01-1.0 μg mL(-1), low limits of detection (0.0005-0.0019 μg mL(-1)), acceptable reproducibility (RSD, 2.26-4.81%, n = 6), and satisfactory relative recoveries (90.9-97.6%). It was demonstrated that RAM-MIPs solid phase extraction with excellent selectivity and restricted access function was a simple, rapid, selective, and effective sample pretreatment method.

  2. Quantification of Tetramethylenedisulfotetramine (TETS) in Various Food Matrices by Solid Phase Extraction Liquid ChromatographyIon Trap Mass Spectrometry

    Science.gov (United States)

    2017-04-01

    used to deliberately contaminate food or water . TETS is not absorbed through the skin; the most common route of exposure is ingestion of...TETS in various complex food matrices. TETS is a relatively persistent environmental contaminant due to its high stability in water . This extraction...QUANTIFICATION OF TETRAMETHYLENEDISULFOTETRAMINE (TETS) IN VARIOUS FOOD MATRICES BY SOLID-PHASE EXTRACTION

  3. DNA extraction on bio-chip: history and preeminence over conventional and solid-phase extraction methods.

    Science.gov (United States)

    Ayoib, Adilah; Hashim, Uda; Gopinath, Subash C B; Md Arshad, M K

    2017-09-23

    This review covers a developmental progression on early to modern taxonomy at cellular level following the advent of electron microscopy and the advancement in deoxyribonucleic acid (DNA) extraction for expatiation of biological classification at DNA level. Here, we discuss the fundamental values of conventional chemical methods of DNA extraction using liquid/liquid extraction (LLE) followed by development of solid-phase extraction (SPE) methods, as well as recent advances in microfluidics device-based system for DNA extraction on-chip. We also discuss the importance of DNA extraction as well as the advantages over conventional chemical methods, and how Lab-on-a-Chip (LOC) system plays a crucial role for the future achievements.

  4. Determination of phenolic compounds in wines by novel matrix solid-phase dispersion extraction and gas chromatography/mass spectrometry.

    Science.gov (United States)

    Minuti, Lucio; Pellegrino, Roberto

    2008-03-21

    A novel matrix solid-phase dispersion (MSPD) extraction method was developed to extract simultaneously 23 phenolic compounds from wine samples prior to determination by gas chromatography with mass spectrometric detection in the selected ion monitoring mode. Different parameters of the MSPD technique such as dispersant solid-phase, eluting solvent, and sample ionic strength and pH were optimized. The optimized MSPD procedure requires a small volume of wine (1 mL), commercial silica gel (1.5 g) as dispersant solid-phase and a small volume of ethyl acetate (5 mL) as eluting solvent. Under these conditions, the extraction of the studied compounds was almost complete (mean values of recoveries between 87 and 109%) in a short time (15 min). Moreover, satisfactory standard deviations of repeatability (RSD0.993) and detection limits (wines. Application was illustrated by analysis of different wine samples.

  5. Carbon nanotubes as solid-phase extraction sorbents prior to atomic spectrometric determination of metal species: A review

    Energy Technology Data Exchange (ETDEWEB)

    Herrero Latorre, C., E-mail: carlos.herrero@usc.es [Universidad de Santiago de Compostela, Dpto. Quimica Analitica, Nutricion y Bromatologia, Facultad de Ciencias, Alfonso X el Sabio s/n, 27002 Lugo (Spain); Alvarez Mendez, J.; Barciela Garcia, J.; Garcia Martin, S.; Pena Crecente, R.M. [Universidad de Santiago de Compostela, Dpto. Quimica Analitica, Nutricion y Bromatologia, Facultad de Ciencias, Alfonso X el Sabio s/n, 27002 Lugo (Spain)

    2012-10-24

    Highlights: Black-Right-Pointing-Pointer The use of CNTs as sorbent for metal species in solid phase extraction has been described. Black-Right-Pointing-Pointer Physical and chemical strategies for functionalization of carbon nanotubes have been discussed. Black-Right-Pointing-Pointer Published analytical methods concerning solid phase extraction and atomic spectrometric determination have been reviewed. - Abstract: New materials have significant impact on the development of new methods and instrumentation for chemical analysis. From the discovery of carbon nanotubes in 1991, single and multi-walled carbon nanotubes - due to their high adsorption and desorption capacities - have been employed as sorption substrates in solid-phase extraction for the preconcentration of metal species from diverse matrices. Looking for successive improvements in sensitivity and selectivity, in the past few years, carbon nanotubes have been utilized as sorbents for solid phase extraction in three different ways: like as-grown, oxidized and functionalized nanotubes. In the present paper, an overview of the recent trends in the use of carbon nanotubes for solid phase extraction of metal species in environmental, biological and food samples is presented. The determination procedures involved the adsorption of metals on the nanotube surface, their quantitative desorption and subsequent measurement by means of atomic spectrometric techniques such as flame atomic absorption spectrometry, electrothermal atomic absorption spectrometry or inductively coupled plasma atomic emission spectrometry/mass spectrometry, among others. Synthesis, purification and types of carbon nanotubes, as well as the diverse chemical and physical strategies for their functionalization are described. Based on 140 references, the performance and general properties of the applications of solid phase extraction based on carbon nanotubes for metal species atomic spectrometric determination are discussed.

  6. Insight into the extraction mechanism of polymeric ionic liquid sorbent coatings in solid-phase microextraction.

    Science.gov (United States)

    Ho, Tien D; Cole, William T S; Augusto, Fabio; Anderson, Jared L

    2013-07-12

    An investigation into the mechanism of extraction for polymeric ionic liquid (PIL)-based solid phase microextraction sorbent coatings is described. Four PIL-based coatings, namely, a poly(1-4-vinylbenzyl)-3-hexadecylimidazolium bis[(trifluoromethyl)sulfonyl] imide (poly([VBHDIM][NTf2])) PIL produced through 2,2'-azo-bis(isobutyronitrile) (AIBN) initiated free-radical polymerization, a UV-initiated poly(1-vinyl-3-hexylimidazolium) chloride (poly([VHIM][Cl])) PIL, and two crosslinked PILs containing the same IL monomers copolymerized with dicationic IL crosslinkers, were investigated. Calibration curves of 1-octanol were plotted in the presence of naphthalene, a model interfering compound, to observe changes in the linear range, sensitivity, and amount of analytes extracted. Results were compared with a polydimethylsiloxane/divinylbenzene (PDMS/DVB) coating and a polyacrylate (PA) coating which are known to extract analytes primarily through adsorption and partitioning mechanisms, respectively. All PIL-based coatings extracted analytes via a non-competitive partitioning mechanism regardless of the extent of crosslinking.

  7. Mixed micelle cloud point-magnetic dispersive μ-solid phase extraction of doxazosin and alfuzosin.

    Science.gov (United States)

    Gao, Nannan; Wu, Hao; Chang, Yafen; Guo, Xiaozhen; Zhang, Lizhen; Du, Liming; Fu, Yunlong

    2015-01-01

    Mixed micelle cloud point extraction (MM-CPE) combined with magnetic dispersive μ-solid phase extraction (MD-μ-SPE) has been developed as a new approach for the extraction of doxazosin (DOX) and alfuzosin (ALF) prior to fluorescence analysis. The mixed micelle anionic surfactant sodium dodecyl sulfate and non-ionic polyoxyethylene(7.5)nonylphenylether was used as the extraction solvent in MM-CPE, and diatomite bonding Fe₃O₄ magnetic nanoparticles were used as the adsorbent in MD-μ-SPE. The method was based on MM-CPE of DOX and ALF in the surfactant-rich phase. Magnetic materials were used to retrieve the surfactant-rich phase, which easily separated from the aqueous phase under magnetic field. At optimum conditions, a linear relationship between DOX and ALF was obtained in the range of 5-300 ng mL(-1), and the limits of detection were 0.21 and 0.16 ng mL(-1), respectively. The proposed method was successfully applied for the determination of the drugs in pharmaceutical preparations, urine samples, and plasma samples.

  8. Mixed micelle cloud point-magnetic dispersive μ-solid phase extraction of doxazosin and alfuzosin

    Science.gov (United States)

    Gao, Nannan; Wu, Hao; Chang, Yafen; Guo, Xiaozhen; Zhang, Lizhen; Du, Liming; Fu, Yunlong

    2015-01-01

    Mixed micelle cloud point extraction (MM-CPE) combined with magnetic dispersive μ-solid phase extraction (MD-μ-SPE) has been developed as a new approach for the extraction of doxazosin (DOX) and alfuzosin (ALF) prior to fluorescence analysis. The mixed micelle anionic surfactant sodium dodecyl sulfate and non-ionic polyoxyethylene(7.5)nonylphenylether was used as the extraction solvent in MM-CPE, and diatomite bonding Fe3O4 magnetic nanoparticles were used as the adsorbent in MD-μ-SPE. The method was based on MM-CPE of DOX and ALF in the surfactant-rich phase. Magnetic materials were used to retrieve the surfactant-rich phase, which easily separated from the aqueous phase under magnetic field. At optimum conditions, a linear relationship between DOX and ALF was obtained in the range of 5-300 ng mL-1, and the limits of detection were 0.21 and 0.16 ng mL-1, respectively. The proposed method was successfully applied for the determination of the drugs in pharmaceutical preparations, urine samples, and plasma samples.

  9. Electrospun composite of polypyrrole-polyamide as a micro-solid phase extraction sorbent.

    Science.gov (United States)

    Bagheri, Habib; Aghakhani, Ali; Akbari, Maryam; Ayazi, Zahra

    2011-07-01

    A micro-solid phase extraction technique was developed using a novel polypyrrole-polyamide nanofiber sheet, fabricated by electrospinning method. The applicability of the new nanofiber sheet was examined as an extracting medium to isolate malathion as a model pesticide from aqueous samples. Solvent desorption was subsequently performed in a microvial, and an aliquot of extractant was injected into gas chromatography-mass spectrometry. Various parameters affecting the electrospinning process including monomer concentration, polyamide content, applied voltage, and electrospinning time were examined. After fabricating the most suitable preparation conditions, influential parameters on the extraction and desorption processes were optimized. The developed method proved to be rather convenient and offers sufficient sensitivity and good reproducibility. The limit of detection (S/N = 3) and limit of quantification (S/N = 10) of the method under optimized conditions were 50 and 100 ng L(-1), respectively. The relative standard deviation at concentration level of 1 ng mL(-1) was 2% (n = 3). The calibration curve of analyte showed linearity in the range of 0.1-1 ng mL(-1) (R (2) = 0.9975). The developed method was successfully applied to tap and Zayanderood river water samples, while the relative recovery percentages of 98% and 96% were obtained, respectively. The whole procedure showed to be conveniently applicable and quite easy to be manipulated.

  10. Volatile composition of peppermint (Mentha piperita L.) commercial teas through solid phase extraction.

    Science.gov (United States)

    Riachi, L G; Abi-Zaid, I E; Moreira, R F A; De Maria, C A B

    2012-12-01

    Volatiles from aqueous extract of peppermint commercial sachets were investigated through gas chromatography/flame ionization detection (GC/FID) and GC/mass spectrometry (MS). Samples were prepared under similar conditions as in homemade tea. Volatiles were isolated using solid phase extraction method (SPE) with Porapak Q trap followed by desorption with acetone. Estimated mean values for short and medium chain carboxylic acids (C2-C12) and ketones lay in the range of 50-64 microg kg(-1) whilst aliphatic alcohols and acyclic hydrocarbons had values lower than 6 microg kg(-1). The major volatiles were terpenes (275-382 microg kg(-1)) that reached 89 % of the total composition. A total of 16 compounds, among them dodecane, acetoin, acetol, citral, geraniol and octanoic acid have been described by the first time in peppermint tea. These findings could be attributed to the different analytical approach employed, mainly to the use of different extraction/pre-concentration techniques. Given the apparently lower proportion of terpenes in the aqueous extract it may be that the chemical properties of the peppermint essential oil are not entirely reproduced with homemade tea.

  11. Magnetic solid-phase extraction of protein with deep eutectic solvent immobilized magnetic graphene oxide nanoparticles.

    Science.gov (United States)

    Xu, Kaijia; Wang, Yuzhi; Ding, Xueqin; Huang, Yanhua; Li, Na; Wen, Qian

    2016-01-01

    As a new type of green solvent, four kinds of choline chloride (ChCl)-based deep eutectic solvents (DESs) have been synthesized, and then a core-shell structure magnetic graphene oxide (Fe3O4-NH2@GO) nanoparticles have been prepared and coated with the ChCl-based DESs. Magnetic solid-phase extraction (MSPE) based Fe3O4-NH2@GO@DES was studied for the first time for the extraction of proteins. The characteristic results of vibrating sample magnetometer (VSM), X-ray diffraction (XRD), Fourier transform infrared spectrometry (FT-IR), thermal gravimetric analysis (TGA) and field emission scanning electron microscopy (FESEM) indicated the successful preparation of Fe3O4-NH2@GO@DES. The concentrations of proteins in studies were determined by a UV-vis spectrophotometer. The advantages of Fe3O4-NH2@GO@DES in protein extraction were compared with Fe3O4-NH2@GO and Fe3O4-NH2, and Fe3O4-NH2@GO@ChCl-glycerol was selected as the suitable extraction solvent. The influence factors of the extraction process such as the pH value, the temperature, the extraction time, the concentration of protein and the amount of Fe3O4-NH2@GO@ChCl-glycerol were evaluated. Desorption experimental result showed 98.73% of BSA could be eluted from the solid extractant with 0.1 mol/L Na2HPO4 solution contained 1 mol/L NaCl. Besides, the conformation of BSA was not changed during the elution by the investigation of circular dichromism (CD) spectra. Furthermore, the analysis of real sample demonstrated that the prepared magnetic nanoparticles did have extraction ability on proteins in bovine whole blood.

  12. Determination of volatile organic compounds in river water by solid phase extraction and gas chromatography

    Institute of Scientific and Technical Information of China (English)

    M. A. Mottaleb; M. Z. Abedin; M. S. Islam

    2004-01-01

    A simple, rapid, and reproducible method is described employing solid-phase extraction(SPE) using dichloromethane followed by gas chromatography(GC) with flame ionization detection(FID) for determination of volatile organic compound(VOC) from the Buriganga River water of Bangladesh. The method was applied to detect the benzene, toluene, ethylbenzene, xylene and cumene(BTEXC) in the sample collected from the surface or 15 cm depth of water. Two-hundred ml of n-hexane-pretreated and filtered water samples were applied directly to a C18 SPE column. BTEXC were extracted with dichloromethane and average concentrations were obtained as 0.104 to 0.372 (g/ml. The highest concentration of benzene was found as 0.372 (g/ml with a relative standard deviation(RSD) of 6.2%, and cumene was not detected. Factors influencing SPE e.g., adsorbent types, sample load volume, eluting solvent, headspace and temperatures, were investigated. A cartridge containing a C18 adsorbent and using dichloromethane gave better performance for extraction of BTEXC from water.Average recoveries exceeding 90% could be achieved for cumene at 4℃with a 2.7%RSD

  13. Oxysterols in cosmetics-Determination by planar solid phase extraction and gas chromatography-mass spectrometry.

    Science.gov (United States)

    Schrack, S; Hohl, C; Schwack, W

    2016-11-18

    Sterol oxidation products (SOPs) are linked to several toxicological effects. Therefore, investigation of potential dietary uptake sources particularly food of animal origin has been a key issue for these compounds. For the simultaneous determination of oxysterols from cholesterol, phytosterols, dihydrolanosterol and lanosterol in complex cosmetic matrices, planar solid phase extraction (pSPE) was applied as clean-up tool. SOPs were first separated from more non-polar and polar matrix constituents by normal phase thin-layer chromatography and then focussed into one target zone. Zone extraction was performed with the TLC-MS interface, followed by gas chromatography-mass spectrometry analysis. pSPE showed to be effective for cleaning up cosmetic samples as sample extracts were free of interferences, and gas chromatographic columns did not show any signs of overloading. Recoveries were between 86 and 113% with relative standard deviations of below 10% (n=6). Results of our market survey in 2016 showed that some cosmetics with ingredients of plant origin contained phytosterol oxidation products (POPs) in the low ppm range and therefore in line with levels reported for food. In lanolin containing products, total SOPs levels (cholesterol oxidation products (COPs), lanosterol oxidation products (LOPs), dihydrolanosterol oxidation products (DOPs)) being in the low percent range exceeded reported levels for food by several orders of magnitudes. Copyright © 2016 Elsevier B.V. All rights reserved.

  14. Optimization of cloud point extraction and solid phase extraction methods for speciation of arsenic in natural water using multivariate technique

    Energy Technology Data Exchange (ETDEWEB)

    Baig, Jameel A., E-mail: jab_mughal@yahoo.com [National Center of Excellence in Analytical Chemistry, University of Sindh, Jamshoro 76080, Sindh (Pakistan); Kazi, Tasneem G., E-mail: tgkazi@yahoo.com [National Center of Excellence in Analytical Chemistry, University of Sindh, Jamshoro 76080, Sindh (Pakistan); Shah, Abdul Q., E-mail: aqshah07@yahoo.com [National Center of Excellence in Analytical Chemistry, University of Sindh, Jamshoro 76080, Sindh (Pakistan); Arain, Mohammad B. [National Center of Excellence in Analytical Chemistry, University of Sindh, Jamshoro 76080, Sindh (Pakistan); Afridi, Hassan I., E-mail: hassanimranafridi@yahoo.com [National Center of Excellence in Analytical Chemistry, University of Sindh, Jamshoro 76080, Sindh (Pakistan); Kandhro, Ghulam A., E-mail: gakandhro@yahoo.com [National Center of Excellence in Analytical Chemistry, University of Sindh, Jamshoro 76080, Sindh (Pakistan); Khan, Sumaira, E-mail: skhanzai@gmail.com [National Center of Excellence in Analytical Chemistry, University of Sindh, Jamshoro 76080, Sindh (Pakistan)

    2009-09-28

    The simple and rapid pre-concentration techniques viz. cloud point extraction (CPE) and solid phase extraction (SPE) were applied for the determination of As{sup 3+} and total inorganic arsenic (iAs) in surface and ground water samples. The As{sup 3+} was formed complex with ammonium pyrrolidinedithiocarbamate (APDC) and extracted by surfactant-rich phases in the non-ionic surfactant Triton X-114, after centrifugation the surfactant-rich phase was diluted with 0.1 mol L{sup -1} HNO{sub 3} in methanol. While total iAs in water samples was adsorbed on titanium dioxide (TiO{sub 2}); after centrifugation, the solid phase was prepared to be slurry for determination. The extracted As species were determined by electrothermal atomic absorption spectrometry. The multivariate strategy was applied to estimate the optimum values of experimental factors for the recovery of As{sup 3+} and total iAs by CPE and SPE. The standard addition method was used to validate the optimized methods. The obtained result showed sufficient recoveries for As{sup 3+} and iAs (>98.0%). The concentration factor in both cases was found to be 40.

  15. Determination of crystal violet in water by direct solid phase spectrophotometry after rotating disk sorptive extraction.

    Science.gov (United States)

    Manzo, Valentina; Navarro, Orielle; Honda, Luis; Sánchez, Karen; Inés Toral, M; Richter, Pablo

    2013-03-15

    The microextraction of crystal violet (CV) from water samples into polydimethylsiloxane (PDMS) using the rotating disk sorptive extraction (RDSE) technique was performed. The extracting device was a small Teflon disk that had an embedded miniature magnetic stirring bar and a PDMS (560 μL) film attached to one side of the disk using double-sided tape. The extraction involves a preconcentration of CV into the PDMS, where the analyte is then directly quantified using solid phase spectrophotometry at 600 nm. Different chemical and extraction device-related variables were studied to achieve the best sensitivity for the determination. The optimum extraction was performed at pH 14 because under this condition, CV is transformed to the neutral and colorless species carbinol, which can be quantitatively transferred to the PDMS phase. Although the colorless species is the chemical form extracted in the PDMS, an intense violet coloration appeared in the phase because the -OH bond in the carbinol molecule is weakened through the formation of hydrogen bonds with the oxygen atoms of the PDMS, allowing the resonance between the three benzene rings to compensate for the charge deficit on the central carbon atom of the molecule. The accuracy and precision of the method were evaluated in river water samples spiked with 10 and 30 μg L(-1) of CV, yielding a relative standard deviation of 6.2% and 8.4% and a recovery of 98.4% and 99.4%, respectively. The method detection limit was 1.8 μg L(-1) and the limit of quantification was 5.4 μg L(-1), which can be decreased if the sample volume is increased.

  16. Steady-state diffusion regime in solid-phase micro extraction kinetics

    NARCIS (Netherlands)

    Benhabib, K.; Laak, ter T.L.; Leeuwen, van H.P.

    2008-01-01

    The temporal evolution of diffusion-controlled analyte accumulation in solid-phase microextraction (SPME) is critically discussed in terms of the various aspects of steady-state diffusion in the two phases under conditions of fast exchange of the analyte at the solid phase film/water interface. For

  17. Combined supercritical fluid extraction/solid-phase extraction with octadecylsilane cartridges as a sample preparation technique for the ultratrace analysis of a drug metabolite in plasma.

    Science.gov (United States)

    Liu, H; Cooper, L M; Raynie, D E; Pinkston, J D; Wehmeyer, K R

    1992-04-01

    Supercritical fluid extraction was coupled with solid-phase extraction using octadecylsilane cartridges for the selective isolation of ultratrace levels of a drug metabolite, mebeverine alcohol, from plasma. Plasma was directly applied to the extraction cartridge, the cartridge was washed to remove protein and then extracted under supercritical conditions using CO2/5% methanol. The effluent from the extraction cell was bubbled through a small volume of 2-propanol to trap the extracted mebeverine alcohol. The effects of extraction pressure and temperature on analyte recovery were examined. The absolute recovery, selectivity, precision, and accuracy of the combined supercritical fluid extraction/solid-phase extraction approach were compared to those of conventional solid-phase extraction using gas chromatography/mass spectrometry in the selected-ion monitoring mode. Mebeverine alcohol was used as a model compound, and dog plasma was employed as the biological matrix for these studies.

  18. Molecularly imprinted polymers based on SBA-15 for selective solid-phase extraction of baicalein from plasma samples.

    Science.gov (United States)

    He, Hongliang; Gu, Xiaoli; Shi, Liying; Hong, Junli; Zhang, Hongjuan; Gao, Yankun; Du, Shuhu; Chen, Lina

    2015-01-01

    Highly selective molecularly imprinted mesoporous silica polymer (SBA-15@MIP) for baicalein (BAI) extraction was synthesized using a surface molecular imprinting technique on the SBA-15 supporter. Computational simulation was used to predict the optimal functional monomer for the rational design of SBA-15@MIP. Meanwhile, high adsorption capacity was obtained when a suitable yield of molecularly imprinted polymers (MIPs) layer was grafted onto the surface of SBA-15. Characterization and performance tests of the obtained polymer revealed that SBA-15@MIP possessed a highly ordered mesoporous structure, reached saturated adsorption within 60 min, and exhibited higher sorption capacity to the target molecule BAI compared with non-imprinted mesoporous silica polymer (SBA-15@NIP) and SBA-15. Finally, SBA-15@MIP was successfully applied to solid-phase extraction (SPE) coupled with high-performance liquid chromatography and ultraviolet detection (HPLC-UV) for the determination of trace BAI in plasma samples. Mean recoveries of BAI through the molecularly imprinted solid-phase extraction (MISPE) sorbent, non-imprinted solid-phase extraction (NISPE) sorbent, and SBA-15 solid-phase extraction (SBA-15-SPE) sorbent were 94.4, 22.7, and 10.7 %, respectively, and the relative standard deviations were 2.9, 2.6, and 3.6 %, respectively. These results reveal that SBA-15@MIP as a SPE sorbent has good applicability to selectively separate and enrich trace BAI from complex samples.

  19. Determination of Scopolamine in Human Saliva Using Solid Phase Extraction and LC/MS/MS

    Science.gov (United States)

    Wang, Zuwei; Vaksman, Zalman; Boyd, Jason; Putcha, Lakshmi

    2007-01-01

    Purpose: Scopolamine is the preferred treatment for motion sickness during space flight because of its quick onset of action, short half-life and favorable side-effect profile. The dose administered depends on the mode of administration and usually ranges between 0.1 and 0.8 mg. Such small doses make it difficult to detect concentrations of scopolamine in biological fluids by using conventional HPLC methods. To measure scopolamine in saliva and thereby to evaluate the pharmacokinetics of scopolamine, we developed an LC/MS/MS method using off-line solid phase extraction. Method: Samples (0.5mL) were loaded onto Waters Oasis HLB co-polymer cartridges (10 mg, 1 mL) and eluted with 0.5 mL methanol without evaporation and reconstitution. HPLC separation of the eluted sample was performed using an Agilent Zorbax SB-CN column (50 x 2.1 mm) at a flow rate of 0.2 mL/min for 4 minutes. The mobile phase for separation was 90:10 (v/v) methanol: ammonium acetate (2 mM) in water, pH 5.0 +/- 0.1. Concentrations of scopolamine were determined using a Micromass Quattro Micro(TM) mass spectrometer with electrospray ionization (ESI). ESI mass spectra were acquired in positive ion mode with multiple reaction monitoring for the determination of scopolamine m/z = 304.2 yields 138.1 and internal standard (IS) hyoscyamine m/z = 290.2 yields 124.1. Results: The method is rapid, reproducible, specific and has the following parameters: scopolamine and the IS are eluted at 1.7 and 3.2 min respectively. The linear range is 50-5000 pg/mL for scopolamine in saliva with correlation coefficients > 0.99 with a CV saliva. Conclusion: Solid phase extraction allows more rapid sample preparation and greater precision than liquid extraction. Furthermore, we increased the sensitivity and specificity by adjusting the LC mobile phase and using an MS/MS detector.

  20. [Determination of polyphenols in tobacco by solid phase extraction and high performance liquid chromatography].

    Science.gov (United States)

    Wang, L; Fang, R B; Li, Z; Jiang, C Q; Yang, G Y

    2001-11-01

    A high performance liquid chromatographic (HPLC) method for the determination of polyphenols in tobacco was studied. Polyphenols can be extracted from tobacco sample by refluxing with 80% (volume fraction) methanol, then subjected to degrease by solid phase extraction with Sep-Pak-C18 column. Chlorogenic acid, rutin, scopoletin, caffeic acid, scopolin and other polyphenols can be separated on a Nova-Pak-C18 column (3.9 mm i.d. x 150 mm) gradiently eluted with methanol and 0.05 mol.L-1 potassium dihydrogen phosphate buffer solution as mobile phase at a flow-rate of 0.5 mL.min-1. Polyphenols were determined at the maximum wavelength of each polyphenol, for chlorogenic acid 326.1 nm, rutin 354.8 nm, scopoletin 344.0 nm, caffeic acid 323.7 nm and scopolin 365.2 nm by photodiode array detector. The main polyphenols in tobacco can be identified with UV spectroscopy. The recoveries of tobacco polyphenols were 94%-105%, and the relative standard deviations were 1.28%-1.49%. This method can be applied to the determination of polyphenols in tobacco with satisfactory results.

  1. Solid-phase extraction with metal-organic frameworks for the analysis of chiral compounds.

    Science.gov (United States)

    Tang, Bo; Zhang, Jun-Hui; Zi, Min; Chen, Xue-Xian; Yuan, Li-Ming

    2016-12-01

    Metal-organic frameworks (MOFs) are excellent porous materials with nanoscale cavities and high surface areas, which make them promising as novel adsorbents in solid-phase extraction (SPE). In this article we report a new application of the chiral MOF [Zn2 (D-Cam)2 (4,4'-bpy)]n in SPE used for the measurement of the enantiomeric excess (ee) of (±)-1,1'-bi-2-naphthol. Several important experimental parameters that may influence the extraction efficiency were investigated and optimized. Under the optimum conditions, a good linearity (R(2)  > 0.999) was found between the ee value and the reciprocal of the peak areas. When compared with the actual ee measured using chiral HPLC, the SPE-based assay also showed good accuracy and precision. The results showed that SPE based on chiral MOFs as adsorbents is a simple and effective method for the determination of the ee values of chiral compounds. © 2016 Wiley Periodicals, Inc.

  2. Solid phase extraction of uranium(VI) onto benzoylthiourea-anchored activated carbon.

    Science.gov (United States)

    Zhao, Yongsheng; Liu, Chunxia; Feng, Miao; Chen, Zhen; Li, Shuqiong; Tian, Gan; Wang, Li; Huang, Jingbo; Li, Shoujian

    2010-04-15

    A new solid phase extractant selective for uranium(VI) based on benzoylthiourea anchored to activated carbon was developed via hydroxylation, amidation and reaction with benzoyl isothiocyanate in sequence. Fourier transform infrared spectroscopy and total element analysis proved that benzoylthiourea had been successfully grafted to the surface of the activated carbon, with a loading capacity of 1.2 mmol benzoylthiourea per gram of activated carbon. The parameters that affect the uranium(VI) sorption, such as contact time, solution pH, initial uranium(VI) concentration, adsorbent dose and temperature, have been investigated. Results have been analyzed by Langmuir and Freundlich isotherm; the former was more suitable to describe the sorption process. The maximum sorption capacity (82 mg/g) for uranium(VI) was obtained at experimental conditions. The rate constant for the uranium sorption by the as-synthesized extractant was 0.441 min(-1) from the first order rate equation. Thermodynamic parameters (DeltaH(0)=-46.2 kJ/mol; DeltaS(0)=-98.0 J/mol K; DeltaG(0)=-17.5 kJ/mol) showed the adsorption of an exothermic process and spontaneous nature, respectively. Additional studies indicated that the benzoylthiourea-anchored activated carbon (BT-AC) selectively sorbed uranyl ions in the presence of competing ions, Na(+), Co(2+), Sr(2+), Cs(+) and La(3+).

  3. Selective solid-phase extraction of uranium by salicylideneimine-functionalized hydrothermal carbon.

    Science.gov (United States)

    Wang, Hang; Ma, Lijian; Cao, Kecheng; Geng, Junxia; Liu, Jun; Song, Qiang; Yang, Xiaodan; Li, Shoujian

    2012-08-30

    A new salicylideneimine-functionalized hydrothermal-carbon-based solid-phase extractant was developed for the purpose of separating uranium selectively for sustainability of uranium resources. The resulting adsorption material was obtained via hydrothermal carbonization, calcination at mild temperature (573.15K), amination, and grafting with salicylaldehyde in sequence. Both Fourier transform infrared spectra and elemental analysis proved the successful grafting of salicylideneimine onto hydrothermal carbon matrix. Adsorption behaviors of the extractant on uranium(VI) were investigated by varying pH values of solution, adsorbent amounts, contact times, initial metal concentrations, temperatures, and ionic strengths. An optimum adsorption capacity of 1.10 mmol g(-1) (261 mg g(-1)) for uranium(VI) was obtained at pH 4.3. The present adsorption process obeyed pseudo-second-order model and Langmuir isotherm. Thermodynamic parameters (ΔH=+8.81 kJ mol(-1), ΔS=+110 J K(-1)mol(-1), ΔG=-23.0 kJ mol(-1)) indicated the adsorption process was endothermic and spontaneous. Results from batch adsorption test in simulated nuclear industrial effluent, containing Cs(+), Sr(2+), Ba(2+), Mn(2+), Co(2+), Ni(2+), Zn(2+), La(3+), Ce(3+), Nd(3+), Sm(3+), and Gd(3+), showed the adsorbent could separate uranium(VI) from those competitive ions with high selectivity. The adsorbent might be promising for use in certain key steps in any future sustainable nuclear fuel cycle.

  4. Determination of organic acids in Salicornia herbacea by solid-phase extraction combined with liquid chromatography.

    Science.gov (United States)

    Han, Dandan; Tian, Minglei; Park, Dong Wha; Row, Kyung Ho

    2013-02-01

    A solid-phase extraction (SPE) method for the determination of procatechuic acid, ferulic acid and caffeic acid in Salicornia herbacea L. (Hamcho) has been developed. The optimal conditions were obtained by using a C18 SPE cartridge. By using ethanol and acetonitrile /water/ trifluoracetic acid as washing and eluting solvents, most interfering compounds originating from the hamcho matrix were eliminated. The extracts were sufficiently clean to be directly injected into the HPLC for further chromatographic analysis. Good linearity was obtained from 0.1 to 200 microg/mL (r > 0.999) for procatechuic acid, 0.2 to 400 microg/mL (r > 0.999) for caffeic acid and 0.3 to 600 microg/mL (r > 0.999) for ferulic acid, with the relative standard deviations being less than 3.6%. The mean recoveries of procatechuic acid, ferulic acid and caffeic acid from hamcho were more than 79.2% and the detection limit (S/N = 3:1) was 0.02 microg/mL for procatechuic acid, 0.01 microg/mL for caffeic acid and 0.04 microg/mL for ferulic acid. This method is a viable alternative to the existing HPLC methods for analyzing the content of procatechuic acid, ferulic acid and caffeic acid in hamcho.

  5. Determination of Metamizole Sodium and Chlorphenamine Maleate in Zhongganling Tablets by Solid-Phase Extracting HPLC

    Institute of Scientific and Technical Information of China (English)

    HANG Yiying; ZHU Binghui; LU Huiwen; YU Jinxiong; DEN Zhihua

    2002-01-01

    Objective To establish a method for the determination of metamizole sodium and chlorphenamine maleate in Zhongganling tablets. Methods The sample was determined by ion - pair HPLC after it was purified on Sep- Pak C18 microcolumn. The chromatographic conditions included: Hypersil DBS C18 chromatographic column(250mm × 4.6mm, i.d. 5μm) as an analytical column, methanolmixed solution of sodium heptanesulfonate and glacial acetic acid(600:400) as a mobile phase, the demetamizole sodium and chlorphenamine malcate were 99.6% (RSD was 2.1% and n was 6) and 98.0%(RSD was 1.5% and n was 6), respectively. Conclusion Metamizole sodium and chlorphenamine malcate can be determined respectively by HPLC with the same mobile phase when Sep - Pak C18 microcolumn solid- phase extraction method is used to substitute for the traditional sample pretreatment methods - refluxing, extracting and concentrating, and sodim heptanesulfonate ion - pair reagent in acid condition is selected.

  6. Solid Phase Extraction for Monitoring of Occupational Exposure to Cr (III

    Directory of Open Access Journals (Sweden)

    S.J. Shahtaheri

    2007-01-01

    Full Text Available Chromium is an important constituent widely used in different industrial processes for production of various synthetic materials. For evaluation of workers’ exposure to trace toxic metal of Cr (III, environmental and biological monitoring are essential processes, in which, preparation of samples is one of the most time-consuming and error-prone aspects prior to analysis. The use of solid-phase extraction (SPE has grown and is a fertile technique of sample preparation as it provides better results than those produced by liquid-liquid extraction (LLE. SPE using mini columns filled with XAD-4 resin was optimized regarding to sample pH, ligand concentration, loading flow rate, elution solvent, sample volume, elution volume, amount of resins, and sample matrix interferences. Chromium was retained on solid sorbent and was eluted with 2 M HNO3 followed by simple determination of analytes by using flame atomic absorption spectrometery. Obtained recoveries of metal ion were more than 92%. The optimized procedure was also validated with three different pools of spiked urine samples and showed a good reproducibility over six consecutive days as well as six within-day experiments. Through this study, suitable results were obtained for relative standard deviation, therefore, it is concluded that, this optimized method can be considered to be successful in simplifying sample preparation for trace residue analysis of Cr in different matrices for evaluation of occupational and environmental exposures. To evaluate occupational exposure to chromium, 16 urine samples were taken, prepared, and analyzed based on optimized procedure.

  7. Solid-Phase Extraction (SPE: Principles and Applications in Food Samples

    Directory of Open Access Journals (Sweden)

    Semih Ötles

    2016-03-01

    Full Text Available Solid-Phase Extraction (SPE is a sample preparation method that is practised on numerous application fields due to its many advantages compared to other traditional methods. SPE was invented as an alternative to liquid/liquid extraction and eliminated multiple disadvantages, such as usage of large amount of solvent, extended operation time/procedure steps, potential sources of error, and high cost. Moreover, SPE can be ap- plied to the samples combined with other analytical methods and sample preparation techniques optionally. SPE technique is a useful tool for many purposes through its versatility. Isolation, concentration, purification and clean-up are the main approaches in the practices of this method. Food structures represent a complicated matrix and can be formed into different physical stages, such as solid, viscous or liquid. Therefore, sample preparation step particularly has an important role for the determination of specific compounds in foods. SPE offers many opportunities not only for analysis of a large diversity of food samples but also for optimization and advances. This review aims to provide a comprehensive overview on basic principles of SPE and its applications for many analytes in food matrix.

  8. Determination of Three Tanshinones from Radix Salvia Miltiorrhiza by Molecularly Imprinted Solid-phase Extraction

    Institute of Scientific and Technical Information of China (English)

    YAN, Hongyuan; TIAN, Minglei; ROW, Kyung Ho

    2009-01-01

    A selective molecularly imprinted solid-phase extraction procedure was developed for the selective separation of tanshinone Ⅰ, tanshinone ⅡA, and cryptotanshinone from Radix Salvia Miltiorrhiza samples. Tanshinone ⅡA imprinted polymers (MIP) synthesized in ethanol-dodecanol system show high affinity to tanshinone ⅡA and its structure analogs in aqueous environment and the affinity can be controlled by adjusting the intensity of the eluents. By using 60% water-40% methanol (volume ratio) and 99.5% methanol-0.5% trifluoroacetic acid (volume ratio) as washing and eluting solvents, most interferences originating from the salvia matrix were eliminated. The extracts were sufficiently clean enough to be directly injected into HPLC for further chromatographic analysis. Good linearity was obtained from 0.4 to 500.0 mg·L~(-1) (r~2=0.999) with the relative standard deviations less than 4.2%. The mean recoveries of tanshinone ⅡA in Radix Salvia Miltiorrhiza were more than 85.6% at three different concentrations and the limits of detection were 0.06-0.09 mg·L~(-1). This method is a viable alternative tool to the existing HPLC methods for analyzing the content of the three tanshinones in Radix Salvia Miltiorrhiza samples.

  9. Imprinted functionalized silica sol-gel for solid-phase extraction of triazolamin.

    Science.gov (United States)

    Jin, Guoyou; Zhang, Baofei; Tang, Youwen; Zuo, Xiongjun; Wang, Songcai; Tang, Jingyi

    2011-05-15

    A triazolam-imprinted silica microsphere was prepared by combining a surface molecular-imprinting technique with the sol-gel process. The results illustrate that the triazolam-imprinted silica microspheres provided using γ-aminopropyltriethoxysilane and phenyltrimethoxysilane as monomers exhibited higher selectivity than those provided from γ-aminopropyltriethoxysilane and methyltriethoxysilane. In addition, the optimum affinity occurred when the molar ratio of γ-aminopropyltriethoxysilane, phenyltrimethoxysilane, and the template molecule was 4.2:4.7:0.6. Retention factor (k) and imprinting factor (IF) of triazolam on the imprinted and non-imprinted silica microsphere columns were characterized using high performance liquid chromatography (HPLC) with different mobile phases including methanol, acetonitrile, and water solutions. The molecular selectivity of the imprinted silica microspheres was also evaluated for triazolam and its analogue compounds in various mobile phases. The better results indicated that k and IF of triazolam on the imprinted silica microsphere column were 2.1 and 35, respectively, when using methanol/water (1/1, v/v) as the mobile phase. Finally, the imprinted silica was applied as a sorbent in solid-phase extraction (SPE), to selectively extract triazolam and its metabolite, α-hydroxytriazolam, from human urine samples. The limits of detection (LOD) for triazolam and α-hydroxytriazolam in urine samples were 30 ± 0.21 ng mL(-1) and 33 ± 0.26 ng mL(-1), respectively.

  10. Quantitation of drugs via molecularly imprinted polymer solid phase extraction and electrospray ionization mass spectrometry: benzodiazepines in human plasma

    OpenAIRE

    2011-01-01

    The association of solid phase extraction with molecularly imprinted polymers (MIP) and electrospray ionization mass spectrometry (ESI-MS) is applied to the direct extraction and quantitation of benzodiazepines in human plasma. The target analytes are sequestered by MIP and directly analyzed by ESI-MS. Due to the MIP highly selective extraction, ionic suppression during ESI is minimized; hence no separation is necessary prior to ESI-MS, which greatly increases analytical speed. Benzodiazepine...

  11. Rapid analyses of proteomes and interactomes using an integrated solid-phase extraction-liquid chromatography-MS/ms system

    NARCIS (Netherlands)

    Binai, Nadine A.; Marino, Fabio; Soendergaard, Peter; Bache, Nicolai; Mohammed, Shabaz; Heck, Albert J R

    2015-01-01

    Here, we explore applications of a LC system using disposable solid-phase extraction (SPE) cartridges and very short LC-MS/MS gradients that allows for rapid analyses in less than 10 min analysis time. The setup consists of an autosampler harboring two sets of 96 STAGE tips that function as precolum

  12. Use of molecularly imprinted solid-phase extraction for the selective clean-up of clenbuterol from calf urine

    NARCIS (Netherlands)

    Berggren, C; Bayoudh, S; Sherrington, D; Ensing, K

    2000-01-01

    A feasibility study was performed in order to study the possibilities in using molecularly imprinted polymers (MIPs) as sorbent material in solid-phase extraction (MISPE) for clean-up of clenbuterol from urine. A binding study of clenbuterol in several solvents was performed on a clenbuterol imprint

  13. [Determination of phthalic acid esters in textiles by solid phase extraction-gas chromatography].

    Science.gov (United States)

    Niu, Zengyuan; Ye, Xiwen; Fang, Liping; Xue, Qiuhong; Sun, Zhongsong

    2006-09-01

    A method was established for the simultaneous determination of some phthalic acid esters, namely, dimethyl phthalate (DMP), diethyl phthalate (DEP), dipropyl phthalate (DPrP), dibutyl phthalate (DBP), diamyl phthalate (DAP), dihexyl phthalate (DHP), benzyln-butyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP), dicyclohexyl phthalate (DCHP), di-n-octyl phthalate (DNOP), diisononyl phthalate (DINP) and diisodecyl phthalate (DIDP) in textiles by solid phase extraction (SPE) coupled with gas chromatography (GC). The phthalic acid esters in textiles were extracted by Soxhlet extraction with hexane, the extracts were then cleaned up and enriched by a strong anion exchange (SAX) SPE cartridge. The parameters affecting the purification efficiency of SPE cartridge, such as solvent conditioning, rinsing, and elution, were studied. Conditioning with 5 mL hexane and rinsing with 3 mL isooctane were proved to be the optimal conditions. Of the several solvent ratios (ethylacetate in hexane) used for selective elution of phthalic acid esters from the SAX SPE cartridge, the 15% (v/v) content for ethylacetate in hexane gave the best result. Under the optimized conditions, the recoveries of phthalic acid esters for spiked standards (n=7) were 86.3%-102.7%, and the relative standard deviations (RSDs) were less than 5%. In this method the detection limits for DMP, DEP, DPrP, DBP, DAP, BBP, DCHP, DEHP, DNOP were all below 1 mg/kg, and the detection limits for DINP and DIDP were 1.74 mg/kg and 1.55 mg/kg respectively. This SPE-GC method is sensitive, accurate and suitable for the analysis of phthalate environmental hormones in textiles.

  14. A rapid solid-phase extraction fluorometric method for thiamine and riboflavin in salmonid eggs

    Science.gov (United States)

    Zajicek, James L.; Tillitt, Donald E.; Brown, Scott B.; Brown, Lisa R.; Honeyfield, Dale C.; Fitzsimons, John D.

    2005-01-01

    A new method has been developed and successfully applied to the selective measurement of thiamine (nonphosphorylated), total thiamine (sum of thiamine, thiamine monophosphate [TMP], thiamine diphosphate [TDP], and thiamine triphosphate [TTP]), and potentially interfering riboflavin in acidic (2% trichloroacetic acid) extracts of selected salmonid and walleye egg samples. Acidic extracts of eggs were applied directly to end-capped C18, reversed-phase solid-phase extraction (SPE) columns and separated into three fractions by elution with mixtures of PO4 buffer (pH 2), methanol (10%), and acetonitrile (20%). All thiamine compounds recovered in the first two fractions were oxidized to their corresponding thiochromes with alkaline potassium hexacyanoferrate, and we measured the thiochrome fluorescence (excitation at 360 nm, emission at 460 nm) in a 96-well microplate reader. Riboflavin, recovered in third fraction (eluted with pH 2, 20% acetonitrile), was analyzed directly by measuring the fluorescence of this fraction (excitation at 450 nm, emission at 530 nm). Significant portions of the phosphate esters of thiamine (TMP, TDP, and presumably TTP), when present at low concentrations (thiamine per gram of egg), were not retained by the 100-mg SPE column, and were collected directly during sample loading and in a subsequent phosphoric acid rinse as fraction 1. Free thiamine (nonphosphorylated) and remaining portions of the TDP and TMP were then eluted in the second fraction with 10% methanol/PO4 buffer, whereas the un-ionized, relatively nonpolar riboflavin was eluted in the third fraction with 20% acetonitrile. This new method uses a traditional sample homogenization of egg tissue to extract thiamine compounds into 2% trichlororacetic acid solution; an inexpensive, commercially available SPE column; small amounts of sample (0.5-1 g); microliter volumes of solvents per sample; a traditional, relatively nonhazardous, oxidation of thiamine compounds to fluorescent

  15. Dynamic solid phase DNA extraction and PCR amplification in polyester-toner based microchip.

    Science.gov (United States)

    Duarte, Gabriela R M; Price, Carol W; Augustine, Brian H; Carrilho, Emanuel; Landers, James P

    2011-07-01

    A variety of substrates have been used for fabrication of microchips for DNA extraction, PCR amplification, and DNA fragment separation, including the more conventional glass and silicon as well as alternative polymer-based materials. Polyester represents one such polymer, and the laser-printing of toner onto polyester films has been shown to be effective for generating polyester-toner (PeT) microfluidic devices with channel depths on the order of tens of micrometers. Here, we describe a novel and simple process that allows for the production of multilayer, high aspect-ratio PeT microdevices with substantially larger channel depths. This innovative process utilizes a CO(2) laser to create the microchannel in polyester sheets containing a uniform layer of printed toner, and multilayer devices can easily be constructed by sandwiching the channel layer between uncoated cover sheets of polyester containing precut access holes. The process allows the fabrication of deep channels, with ~270 μm, and we demonstrate the effectiveness of multilayer PeT microchips for dynamic solid phase extraction (dSPE) and PCR amplification. With the former, we found that (i) more than 65% of DNA from 0.6 μL of blood was recovered, (ii) the resultant DNA was concentrated to greater than 3 ng/μL (which was better than other chip-based extraction methods), and (iii) the DNA recovered was compatible with downstream microchip-based PCR amplification. Illustrative of the compatibility of PeT microchips with the PCR process, the successful amplification of a 520 bp fragment of λ-phage DNA in a conventional thermocycler is shown. The ability to handle the diverse chemistries associated with DNA purification and extraction is a testimony to the potential utility of PeT microchips beyond separations and presents a promising new disposable platform for genetic analysis that is low cost and easy to fabricate.

  16. High-performance liquid chromatographic (HPLC) separation and quantitation of endogenous glucocorticoids after solid-phase extraction from plasma.

    Science.gov (United States)

    Dawson, R; Kontur, P; Monjan, A

    1984-01-01

    This study describes a method for the extraction and simultaneous measurement of cortisone, cortisol and corticosterone using dexamethasone as an internal standard. Solid-phase extraction of plasma steroids with C18 columns allows the samples to be extracted, washed and concentrated in a single step with minimal sample handling and without the use of large volumes of organic solvents. HPLC separation of the steroids is accomplished within 10 min and the individual steroid peaks are quantitated by UV detection at 239 nm. This assay was examined for linearity, extraction efficiency, precision and potential interference by commonly used drugs. Plasma values of glucocorticoids are reported for samples obtained from human subjects as well as from rats. HPLC was also compared to RIA for the determination of plasma levels of corticosterone in the rat. Solid-phase extraction and assay by HPLC provides a rapid and specific method for the simultaneous determination of plasma glucocorticoids.

  17. Fully automated determination of 74 pharmaceuticals in environmental and waste waters by online solid phase extraction-liquid chromatography-electrospray-tandem mass spectrometry.

    Science.gov (United States)

    López-Serna, Rebeca; Pérez, Sandra; Ginebreda, Antoni; Petrović, Mira; Barceló, Damià

    2010-12-15

    The present work describes the development of a fully automated method, based on on-line solid-phase extraction (SPE)-liquid chromatography-electrospray-tandem mass spectrometry (LC-MS-MS), for the determination of 74 pharmaceuticals in environmental waters (superficial water and groundwater) as well as sewage waters. On-line SPE is performed by passing 2.5 mL of the water sample through a HySphere Resin GP cartridge. For unequivocal identification and confirmation two selected reaction monitoring (SRM) transitions are monitored per compound, thus four identification points are achieved. Quantification is performed by the internal standard approach, indispensable to correct the losses during the solid phase extraction, as well as the matrix effects. The main advantages of the method developed are high sensitivity (limits of detection in the low ng L(-1) range), selectivity due the use of tandem mass spectrometry and reliability due the use of 51 surrogates and minimum sample manipulation. As a part of the validation procedure, the method developed has been applied to the analysis of various environmental and sewage samples from a Spanish river and a sewage treatment plant. Copyright © 2010 Elsevier B.V. All rights reserved.

  18. Molecularly imprinted polymer grafted to porous polyethylene frits: a new selective solid-phase extraction format.

    Science.gov (United States)

    Barahona, Francisco; Turiel, Esther; Martín-Esteban, Antonio

    2011-10-07

    In this paper, a novel format for selective solid-phase extraction based on a molecularly imprinted polymer (MIP) is described. A small amount of MIP has been synthesized within the pores of commercial polyethylene (PE) frits and attached to its surface using benzophenone (BP), a photo-initiator capable to start the polymerisation from the surface of the support material. Key properties affecting the obtainment of a proper polymeric layer, such as polymerisation time and kind of cross-linker were optimised. The developed imprinted material has been applied as a selective sorbent for cleaning extracts of thiabendazole (TBZ), as model compound, from citrus samples. The use of different solvents for loading the analyte in the imprinted frits was investigated, as well as the binding capacity of the imprinted polymer. Imprinted frits showed good selectivity when loads were performed using toluene and a linear relationship was obtained for the target analyte up to 1000 ng of loaded analyte. Prepared composite material was applied to the SPE of TBZ in real samples extracts, showing an impressive clean-up ability. Calibrations showed good linearity in the concentration range of 0.05-5.00 μg g(-1), referred to the original solid sample, and the regression coefficients obtained were greater than 0.996. The calculated detection limit was 0.016 μg g(-1), low enough to satisfactory analysis of TBZ in real samples. RSDs at different spiking levels ranged below 15% in all the cases and imprinted frits were reusable without loss in their performance.

  19. Organic acids and inorganic anions in Bayer liquors by ion chromatography after solid-phase extraction

    Institute of Scientific and Technical Information of China (English)

    ZHONG Fu-jin; CHEN Xiao-qing; ZHANG Shu-chao; LI Yue-ping

    2007-01-01

    A method for the simultaneous separation and determination of organic acids and inorganic anions in Bayer liquors was developed by gradient ion chromatography with suppressed conductivity detection. Formate, acetate, propionate, oxalate, succinate,glutarate, fluoride, chloride and sulfate were separated and determined in 33 min. The samples were pretreated with solid-phase extraction, which has high selectivity for removing a large number of metallic ions in the Bayer liquors, and filtered with a 0.45 μm filter membrane before being injected into the ion chromatographic system. The separation of six organic acids and three inorganic anions was achieved on an IonPac AS11-HC column with KOH as the eluent, and the detection was performed by a conductivity detection mode. No interference is found in the presence of fluorate, chlorate and sulphate when organic acids are determined. The calibration graphs of peak area for all the analytes are linear over a wide range. The relative standard derivation of the peak area of analytes is less than 2.14%. Under optimum conditions the detection ranges from 0.2 to 100.0 mg/L. The average recoveries of the added standards are between 94.3% and 102.8%.

  20. Molecularly imprinted polymers-curcuminoids and its application for solid phase extraction

    Science.gov (United States)

    Wulandari, Meyliana; Amran, M. B.; Lopez, A. B. Descalzo; Urraca, J. L.; Moreno-Bondi, M. C.

    2014-03-01

    Molecularly Imprinted Polymers (MIPs) for the selective recognition properties of curcumin (CUR), a cancer chemopreventive agent were obtained by a non-covalent imprinting approach with bisdemetoxycurcumin (BDMC) as the template molecule. The double bond of BDMC has been reduced in order not to be involved in polymerization and make the template molecules easy to be eluted. Several functional monomers have been evaluated to maximize the interactions with the template molecule during polymerization. MIPs prepared by bulk of N-(2-aminoethyl) metacrylamid hydrochlorideas functional monomer, ethylene glycol dimethacrylate as crosslinker, 2,2'-azobis (2'4-dimethyl valeronitril) as initiator and acetonitrile as porogen. Non-imprinted polymer (NIP) have been also synthesized for reference purposes. UV-vis spectroscopy has been used to predict the template to functional monomer ratio which indicates the formation of 2:1 complexes between monomer and curcumin and the association constants (K11 = 2529 μM and K12 = 1960.75 μM in acetonitrile). The capacity and imprinting factor have been evaluated as stationary phases in high-pressure liquid chromatography to CUR and BDMC. The binding properties and the homogeneity of the binding sites of the different polymers have been studied by Freundlich isotherm modeling and weight average affinity and number of binding sites. One of the foremost applications of molecular imprinting has been in molecularly imprinted solid phase extraction and it has the ability to separate and preconcentrate between closely related compounds in curcuminoids.

  1. Solid phase extraction and determination of carbamate pesticides in water samples by reverse-phase HPLC

    Energy Technology Data Exchange (ETDEWEB)

    Moreno-Tovar, J.; Santos-Delgado, M.J. [Departamento de Quimica Analitica, Facultad de ciencias Quimicas, Universidad Complutense de Madrid (Spain)

    1995-12-31

    Solid phase extraction. SPE. using C{sub 1}8 bonded silica cartridges for trace amounts determination of carbaryl, propoxur, thiram, propham and methiocarb in water samples was studied and the breakthrough volume of the cartridges was established. The high enrichment factor and large injection volume admissible in the isocratic reverse-phase HPLC system allows pesticides determination with UV detection at 22o nm even at a concentration lower than 0.05 mug/L. Purified tap natural and underground water samples were spiked with carbamate pesticides in the concentration range 0.16-16.0 mug/L. Large volumes of samples (up to 2L) were passed through available C{sub 1}8, cartridges and eluted with acetonitrile. The preconcentrated samples were analyzed by HPLC using a Spherisorb ODS column with a 42.58 acetonitrile-water mobile phase. From replicate samples, recovery for the pesticides ranged from 79.0 to 103.7% except for thiran which is not retained. Tehe relative standard deviation (n=4 at 0.16 to 1.61 mug/L concetration level) range from 1.1 to 6.8%. (Author) 14 refs.

  2. A solid-phase extraction approach for the identification of pharmaceutical-sludge adsorption mechanisms

    Institute of Scientific and Technical Information of China (English)

    Laurence Berthod; Gary Roberts; Graham A. Mills

    2014-01-01

    It is important to understand the adsorption mechanism of chemicals and active pharmaceu-tical ingredients (API) on sewage sludge since wastewater treatment plants are the last barrier before the release of these compounds to the environment. Adsorption models were developed considering mostly hydrophobic API-sludge interaction. They have poor predictive ability, especially with ionisable compounds. This work proposes a solid-phase extraction (SPE) approach to estimate rapidly the API-sludge interaction. Sludge-filled SPE cartridges could not be percolated with API spiked mobile phases so different powders were tested as SPE sludge supports. Polytetrafluoroethylene (PTFE) was selected and tested at different PTFE/sludge ratios under eight different adsorption conditions with three API ionisable compounds. The PTFE/sludge mixtures with 50% or less sludge could be used in SPE mode for API sorption studies with methanol/water liquid phases. The results gave insights into API-sludge interactions. It was found that π-π, hydrogen-bonding and charge-charge interactions were as important as hydrophobicity in the adsorption mechanism of charged APIs on sludge.

  3. Determination of rhodamine B in soft drink, waste water and lipstick samples after solid phase extraction.

    Science.gov (United States)

    Soylak, Mustafa; Unsal, Yunus Emre; Yilmaz, Erkan; Tuzen, Mustafa

    2011-08-01

    A new solid phase extraction method is described for sensitive and selective determination of trace levels of rhodamine B in soft drink, food and industrial waste water samples. The method is based on the adsorption of rhodamine B on the Sepabeads SP 70 resin and its elution with 5 mL of acetonitrile in a mini chromatographic column. Rhodamine B was determined by using UV visible spectrophotometry at 556 nm. The effects of different parameters such as pH, amount of rhodamine B, flow rates of sample and eluent solutions, resin amount, and sample volume were investigated. The influences of some alkali, alkali earth and transition metals on the recoveries of rhodamine B were investigated. The preconcentration factor was found 40. The detection limit based on three times the standard deviation of the reagent blank for rhodamine B was 3.14 μg L⁻¹. The relative standard deviations of the procedure were found as 5% in 1×10⁻⁵ mol L⁻¹ rhodamine B. The presented procedure was successfully applied to real samples including soft drink, food and industrial waste water and lipstick samples. Copyright © 2011 Elsevier Ltd. All rights reserved.

  4. [Preparation and application of solid phase extraction packing of zirconia microsphere coated with sulfonated crosslinked polystyrene].

    Science.gov (United States)

    Shen, Shuchang; Liu, Yuhui; Xiao, Xiaoxing

    2013-08-01

    Zirconia microsphere was prepared by polymerization-induced colloid aggregation (PICA) method and carbon-carbon double bond was grafted onto its surface by titanic acid ester coupling reagent. Poly(styrene-divinylbenzene) was synthesized by free radical polymerization by using styrene, divinylbenzene and carbon-carbon double bond on the microsphere surface in solution system, so the polymer was coated on the microsphere surface. After the benzene ring of the polymer was sulfonated, the cation exchange packing for solid phase extraction (SPE) was obtained. The material was characterized by Fourier transform infrared spectroscopy, scanning electron microscope and X-ray energy dispersive spectroscopy. Three herbicides of mesotrione, atrazine and acetochlor in water were determined by the SPE cartridge coupled with high performance liquid chromatography (HPLC). In the range of 0.5 - 3.0 mg/L, the relationships between the peak areas and mass concentrations of mesotrione, atrazine and acetochlor were linear with the correlation coefficients of 0.9936, 0.9925, 0.9919, respectively. The limits of detection were 5.41, 6.72 and 13.4 microg/L for mesotrione, atrazine and acetochlor, respectively. The results showed that the zirconium dioxide microspheres coated with polymer have diameters in the range of about 6 to 8 microm, the SPE cartridges of which have high adsorption rate for the targets.

  5. Plasma mitomycin C concentrations determined by HPLC coupled to solid-phase extraction.

    Science.gov (United States)

    Paroni, R; Arcelloni, C; De Vecchi, E; Fermo, I; Mauri, D; Colombo, R

    1997-04-01

    The aim of this study was to set up a method for quantification of plasma mitomycin C (MMC) concentrations during intravesical chemotherapy delivered in the presence of local bladder hyperthermia (HT). In comparison with existing methods, this assay, characterized by relative simplicity and efficiency, resulted in the facilitation of performance with nondedicated instrumentation or nonspecialized staff. Purification from plasma matrix was carried out by solid-phase extraction under vaccuum. The purified drug was then collected directly into the vials of the HPLC autosampler. Chromatographic analysis was performed on a reversed-phase C18 column with water:acetonitrile (85:15 by vol) as the mobile phase and the UV detector set at 365 nm. The use of porfiromycin as internal standard provided a method with good within-day precision (CV 6.0% at 5 micrograms/L, n = 6), linearity (0.5-50 micrograms/L), and specificity. The lower limit of detection (< or = 0.5 microgram/L) proved to be suitable for plasma pharmacokinetics monitoring in two tested patients treated with MMC + HT for superficial bladder cancer.

  6. Determination of quinolones in plasma samples by capillary electrophoresis using solid-phase extraction.

    Science.gov (United States)

    Hernández, M; Borrull, F; Calull, M

    2000-06-09

    The potential of capillary zone electrophoresis (CZE) and micellar electrokinetic capillary chromatography (MEKC) have been investigated for the separation and quantitative determination of 10 quinolone antibiotics. The influence of different conditions, such as the buffer and pH of the electrolyte, the surfactant and the ion-pairing agents added to the electrolyte and the organic modifier were studied. A buffer consisting of 40 mM sodium tetraborate at pH 8.1 containing 10% (v/v) methanol was found to be a highly efficient electrophoretic system for separating lomefloxacin, enoxacin, norfloxacin, pipemidic acid, ofloxacin, piromidic acid, flumequine, oxolinic acid, cinoxacin and nalidixic acid. A solid-phase extraction method to remove the sample matrix (pig plasma samples) was developed on a C(18) cartridge using a mixture of methanol-water (70:30, v/v). The method is specific and reproducible and mean recoveries were in the range 94.0+/-4.2% and 123.3+/-4.1% for pig plasma samples over the range used. A linear relationship between concentration and peak area for each compound in pig plasma samples was obtained in the concentration range 5-20 mg l(-1) and detection limits were between 1.1 and 2.4 mg l(-1).

  7. Cadmium Extraction from Solutions by Solid-Phase and its Trace Determination

    Energy Technology Data Exchange (ETDEWEB)

    Ashrafi, F.; Attaran, A. M. [Payame Noor University, Sari (Iran, Islamic Republic of); Kermani, N. Memar [Islamic Azad University, Tehran (Iran, Islamic Republic of)

    2008-04-15

    A new sensitive and selective spectrophotometric method for determination of trace amounts of cadmium using a polyvinyl chloride membrane containing bis-(2-ethylhexyl)phthalate as a solid phase extraction medium was investigated. Bis-(2-ethylhexyl)phthalate has used as a plasticizer. Cd(II) in an aqueous solution was trapped on the membrane in the form of colorful Cd (II)-I{sup -} - MG complexes (which MG is malachite green) and the cadmium complex was concentrated in the membrane. The absorbance of the green membrane was measured at 629 nm using a spectrophotometer, and then, the concentration of the cadmium was calculated using a calibration curve, which expressed the relationship between the Cd(II) concentration and the membrane absorbance after coloring for 25 min. The calibration curve was linear in the range of 10-760 μgL{sup -1} cadmium in the test solution. The detection limit based on the 3S{sub bl} criterion was 1.8199 μgL{sup -1} and the relative standard deviations (RSD) were less than 4 % (n=5). The proposed method has been successfully applied to the determination of trace amounts of cadmium in the Tadjan River water sample (Sari-Iran), and the mean value of 28.7 μgL{sup -1} was obtained.

  8. Rapid microfluidic solid-phase extraction system for hyper-methylated DNA enrichment and epigenetic analysis.

    Science.gov (United States)

    De, Arpita; Sparreboom, Wouter; van den Berg, Albert; Carlen, Edwin T

    2014-09-01

    Genetic sequence and hyper-methylation profile information from the promoter regions of tumor suppressor genes are important for cancer disease investigation. Since hyper-methylated DNA (hm-DNA) is typically present in ultra-low concentrations in biological samples, such as stool, urine, and saliva, sample enrichment and amplification is typically required before detection. We present a rapid microfluidic solid phase extraction (μSPE) system for the capture and elution of low concentrations of hm-DNA (≤1 ng ml(-1)), based on a protein-DNA capture surface, into small volumes using a passive microfluidic lab-on-a-chip platform. All assay steps have been qualitatively characterized using a real-time surface plasmon resonance (SPR) biosensor, and quantitatively characterized using fluorescence spectroscopy. The hm-DNA capture/elution process requires less than 5 min with an efficiency of 71% using a 25 μl elution volume and 92% efficiency using a 100 μl elution volume.

  9. Facile fabrication of reduced graphene oxide-encapsulated silica: a sorbent for solid-phase extraction.

    Science.gov (United States)

    Luo, Yan-Bo; Zhu, Gang-Tian; Li, Xiao-Shui; Yuan, Bi-Feng; Feng, Yu-Qi

    2013-07-19

    In this study, a facile hydrothermal reduction strategy was developed for the preparation of reduced graphene oxide-encapsulated silica (SiO2@rGO). Compared with other conventional methods for the synthesis of SiO2@rGO, the proposed strategy endowed the obtained SiO2@rGO with larger amount of immobilized rGO. The prepared functionalized silica shows remarkable adsorption capacity toward chlorophenols (CPs) and peptides. When it was used as solid-phase extraction (SPE) sorbent, a superior recovery could be obtained compared to commercial sorbents, such as C18 silica, graphitized carbon black and carbon nanotubes. Based on these, the prepared material was used as SPE sorbent for the enrichment of CPs, and a method for the analysis of CPs in water samples was established by coupling SPE with high performance liquid chromatography-ultra violet detection (SPE-HPLC/UV). In addition, the obtained SiO2@rGO was further successfully extended to the enrichment of peptides in bovine serum albumin (BSA) digests.

  10. Determination of polychlorinated biphenyls in transformer oil using various adsorbents for solid phase extraction.

    Science.gov (United States)

    Na, Yun-Cheol; Kim, Kang-Jin; Hong, Jongki; Seo, Jung-Ju

    2008-08-01

    Various adsorbents for a solid phase extraction (SPE) method were used to study their ability to separate PCBs from transformer oil to rapidly determine their sub-ppm concentration in the transformer oil. Approximately 90% of the transformer oil could be removed from the PCBs by using a hydrophilic-lipophilic balanced copolymer (HLB) adsorbent, but the recovery of deca-chlorobiphenyl (deca-CB) used as a surrogate was only 24.5% due to lose during this cleanup process. The use of a silica adsorbent gave good results with 89.9% recovery of the deca-CB. The recovery of Aroclor 1242 and 1260 were 95.4 and 90.3% on silica, and 98.9 and 83.5% on HLB, respectively. Acid treatment was an essential step in removing the ambiguous interference peaks to help identify the PCBs. A decreased sensitivity of the electron capture detection (ECD) for PCBs was observed due to the presence of the remaining trace oil after the workup procedure. This loss in sensitivity was allowed for by using tetrachloroxylene as an internal standard, and this was found to be reliable for the criteria of quality control by employing an experiment in which LCS was spiked with 2mg/l of Aroclor 1260 and analyzed each day over a 25 day period. The MDL for the analytical method established in this study is 0.05 mg/l.

  11. Determination of polar aromatic amines using newly synthesized sol-gel titanium (IV) butoxide cyanopropyltriethoxysilane as solid phase extraction sorbent.

    Science.gov (United States)

    Miskam, Mazidatulakmam; Abu Bakar, Nor Kartini; Mohamad, Sharifah

    2014-03-01

    A solid phase extraction (SPE) method has been developed using a newly synthesized titanium (IV) butoxide-cyanopropyltriethoxysilane (Ti-CNPrTEOS) sorbent for polar selective extraction of aromatic amines in river water sample. The effect of different parameters on the extraction recovery was studied using the SPE method. The applicability of the sorbents for the extraction of polar aromatic amines by the SPE was extensively studied and evaluated as a function of pH, conditioning solvent, sample loading volume, elution solvent and elution solvent volume. The optimum experimental conditions were sample at pH 7, dichloromethane as conditioning solvent, 10 mL sample loading volume and 5 mL of acetonitrile as the eluting solvent. Under the optimum conditions, the limit of detection (LOD) and limit of quantification (LOQ) for solid phase extraction using Ti-CNPrTEOS SPE sorbent (0.01-0.2; 0.03-0.61 µg L(-1)) were lower compared with those achieved using Si-CN SPE sorbent (0.25-1.50; 1.96-3.59 µg L(-1)) and C18 SPE sorbent (0.37-0.98; 1.87-2.87 µg L(-1)) with higher selectivity towards the extraction of polar aromatic amines. The optimized procedure was successfully applied for the solid phase extraction method of selected aromatic amines in river water, waste water and tap water samples prior to the gas chromatography-flame ionization detector separation.

  12. Low concentration DNA extraction and recovery using a silica solid phase.

    Science.gov (United States)

    Katevatis, Constantinos; Fan, Andy; Klapperich, Catherine M

    2017-01-01

    DNA extraction from clinical samples is commonly achieved with a silica solid phase extraction column in the presence of a chaotrope. Versions of these protocols have been adapted for point of care (POC) diagnostic devices in miniaturized platforms, but commercial kits require a high amount of input DNA. Thus, when the input clinical sample contains less than 1 μg of total DNA, the target-specific DNA recovery from most of these protocols is low without supplementing the sample with exogenous carrier DNA. In fact, many clinical samples used in the development of POC diagnostics often exhibit target DNA concentrations as low as 3 ng/mL. With the broader goal of improving the yield and efficiency of nucleic acid-based POC devices for dilute samples, we investigated both DNA adsorption and recovery from silica particles by using 1 pg- 1 μg of DNA with a set of adsorption and elution buffers ranging in pH and chaotropic presence. In terms of adsorption, we found that low pH and the presence of chaotropic guanidinium thiocyanate (GuSCN) enhanced DNA-silica adsorption. When eluting with a standard low-salt, high-pH buffer, > 70% of DNA was unrecoverable, except when DNA was initially adsorbed with 5 M GuSCN at pH 5.2. Unrecovered DNA was either not initially adsorbed or irreversibly bound on the silica surface. Recovery was improved when eluting with 95°C formamide and 1 M NaOH, which suggested that DNA-silica-chaotrope interactions are dominated by hydrophobic interactions and hydrogen bonding. While heated formamide and NaOH are non-ideal elution buffers for practical POC devices, the salient results are important for engineering a set of optimized reagents that could maximize nucleic acid recovery from a microfluidic DNA-silica-chaotrope system.

  13. Microwave-Assisted Extraction Followed by Solid-Phase Extraction for the Chromatographic Analysis of Alkaloids in Stephania cepharantha.

    Science.gov (United States)

    Liu, Ying; Xie, Daotao; Kang, Yun; Wang, Yaqin; Yang, Ping; Guo, Jixian; Huang, Jianming

    2016-04-01

    A procedure involving microwave-assisted extraction (MAE) followed by solid-phase extraction (SPE) was established for the extraction and purification of three bisbenzylisoquinoline alkaloids from Stephania cepharantha, and a reversed-phase high-performance liquid chromatography (HPLC) method was developed for the quantification of the target alkaloids. Chromatographic separation was achieved on a Phenomenex Luna Phenyl-Hexyl column. Prior to the HPLC analysis, the alkaloids were rapidly extracted by an optimized MAE process using 0.01 mol/L hydrochloric acid as the solvent. The MAE extract was subsequently purified by SPE using a cation-exchange polymeric cartridge. The MAE-SPE procedure extracted the three alkaloids with satisfactory recoveries ranging from 100.44 to 102.12%. In comparison with the MAE, Soxhlet and ultrasonic-assisted extractions, the proposed MAE-SPE method showed satisfactory cleanup efficiency. Thus, the validated MAE-SPE-HPLC method is specific, accurate and applicable to the determination of alkaloids in S. cepharantha.

  14. [Determination of alkyl-phenols in textiles by in-tube capillary solid-phase extraction-gas chromatography].

    Science.gov (United States)

    Zhang, Luohong; Du, Ting; Zhong, Jiayu

    2015-10-01

    An in-tube capillary solid-phase extraction (SPE) -gas chromatography (GC) method was developed for confirmation and quantitative determination of octylphenol (OP) and nonylphenol (NP) in textiles. To make the in-tube capillary SPE column, the best SPE cartridge was chosen from four kinds of SPE cartridges. The adsorbent in the cartridge was used as the filling material to make the in-tube capillary SPE column. The nature, volume used, flow rate and adsorption capacity of the eluent were compared. Finally, the in-tube capillary solid-phase extraction was combined with gas chromatography to detect the alkyl phenols (APs). Abselut NEXUS extraction cartridge was chosen as the best solid phase extractant. The optimal in-tube capillary SPE extraction conditions were as follows: 1.2 μL methanol and 1.2 μL ultra-pure water for activating the extraction column, 1.2 μL methanol for eluting, 0.4 μL/min for solution loading. The method showed a good linear relationship in the low concentration range, and the enrichment ratios for the APs were about 100 times. The detection limits of octylphenol and nonylphenol were 3.7 μg/L and 4.5 μg/L, respectively. The recoveries of octylphenol were 85.6%-98.2%, and those of nonylphenol were 83.8%-95.7%. The experimental results demonstrated that the method is simple, rapid, and useful for detecting APs in textiles.

  15. Molecularly imprinted polymer/cryogel composites for solid-phase extraction of bisphenol A from river water and wine.

    Science.gov (United States)

    Baggiani, Claudio; Baravalle, Patrizia; Giovannoli, Cristina; Anfossi, Laura; Giraudi, Gianfranco

    2010-05-01

    Superporous monolithic hydrogels (cryogel monoliths) are elastic, sponge-like materials that can be prepared in an aqueous medium through a cryotropic gelation technique. These monoliths show interesting properties for the development of high-throughput solid-phase extraction supports to treat large volumes of aqueous samples. In this work, a cryogel-supported molecularly imprinted solid-phase extraction approach for the endocrine disruptor bisphenol A (BPA) from river water and wine samples is presented. An imprinted polymer with molecular recognition properties for BPA was prepared in acetonitrile by thermal polymerization of a mixture of 4,4'-dihydroxy-2,2-diphenyl-1,1,1,3,3,3-trifluoropropane as a mimic template of BPA, 4-vinylpyridine and trimethylolpropane trimethacrylate in a molar ratio of 1 + 6 + 6. Fine imprinted particles (extraction approach to recover BPA from dilute aqueous samples with minimum pre-loading work-up. The optimized extraction protocol resulted in a reliable MISPE method suitable to selectively extract and preconcentrate BPA from river water and red wine samples, demonstrating the practical feasibility of cryogel-trapped imprinted polymers as solid-phase extraction materials.

  16. Colorimetric Solid Phase Extraction (CSPE): Using Color to Monitor Spacecraft Water Quality

    Science.gov (United States)

    Gazda, Daniel B.; Nolan, Daniel J.; Rutz, Jeffrey A.; Schultz, John R.; Siperko, Lorraine M.; Porter, Marc D.; Lipert, Robert J.; Flint, Stephanie M.; McCoy, J. Torin

    2010-01-01

    In August 2009, an experimental water quality monitoring kit based on Colorimetric Solid Phase Extraction (CSPE) technology was delivered to the International Space Station (ISS). The kit, called the Colorimetric Water Quality Monitoring Kit (CWQMK), was launched as a Station Development Test Objective (SDTO) experiment to evaluate the suitability of CSPE technology for routine use monitoring water quality on the ISS. CSPE is a sorption-spectrophotometric technique that combines colorimetric reagents, solid-phase extraction, and diffuse reflectance spectroscopy to quantify trace analytes in water samples. In CSPE, a known volume of sample is metered through a membrane disk that has been impregnated with an analyte-specific colorimetric reagent and any additives required to optimize the formation of the analyte-reagent complex. As the sample flows through the membrane disk, the target analyte is selectively extracted, concentrated, and complexed. Formation of the analyte-reagent complex causes a detectable change in the color of the membrane disk that is proportional to the amount of analyte present in the sample. The analyte is then quantified by measuring the color of the membrane disk surface using a hand-held diffuse reflectance spectrophotometer (DRS). The CWQMK provides the capability to measure the ionic silver (Ag +) and molecular iodine (I2) in water samples on-orbit. These analytes were selected for the evaluation of CSPE technology because they are the biocides used in the potable water storage and distribution systems on the ISS. Biocides are added to the potable water systems on spacecraft to inhibit microbial growth. On the United States (US) segment of the ISS molecular iodine serves as the biocide, while the Russian space agency utilizes silver as a biocide in their systems. In both cases, the biocides must be maintained at a level sufficient to control bacterial growth, but low enough to avoid any negative effects on crew health. For example, the

  17. Colorimetric Solid Phase Extraction (CSPE): Using Color to Monitor Spacecraft Water Quality

    Science.gov (United States)

    Gazda, Daniel B.; Nolan, Daniel J.; Rutz, Jeffrey A.; Schultz, John R.; Siperko, Lorraine M.; Porter, Marc D.; Lipert, Robert J.; Flint, Stephanie M.; McCoy, J. Torin

    2010-01-01

    In August 2009, an experimental water quality monitoring kit based on Colorimetric Solid Phase Extraction (CSPE) technology was delivered to the International Space Station (ISS). The kit, called the Colorimetric Water Quality Monitoring Kit (CWQMK), was launched as a Station Development Test Objective (SDTO) experiment to evaluate the suitability of CSPE technology for routine use monitoring water quality on the ISS. CSPE is a sorption-spectrophotometric technique that combines colorimetric reagents, solid-phase extraction, and diffuse reflectance spectroscopy to quantify trace analytes in water samples. In CSPE, a known volume of sample is metered through a membrane disk that has been impregnated with an analyte-specific colorimetric reagent and any additives required to optimize the formation of the analyte-reagent complex. As the sample flows through the membrane disk, the target analyte is selectively extracted, concentrated, and complexed. Formation of the analyte-reagent complex causes a detectable change in the color of the membrane disk that is proportional to the amount of analyte present in the sample. The analyte is then quantified by measuring the color of the membrane disk surface using a hand-held diffuse reflectance spectrophotometer (DRS). The CWQMK provides the capability to measure the ionic silver (Ag +) and molecular iodine (I2) in water samples on-orbit. These analytes were selected for the evaluation of CSPE technology because they are the biocides used in the potable water storage and distribution systems on the ISS. Biocides are added to the potable water systems on spacecraft to inhibit microbial growth. On the United States (US) segment of the ISS molecular iodine serves as the biocide, while the Russian space agency utilizes silver as a biocide in their systems. In both cases, the biocides must be maintained at a level sufficient to control bacterial growth, but low enough to avoid any negative effects on crew health. For example, the

  18. On-line electrochemically controlled in-tube solid phase microextraction of inorganic selenium followed by hydride generation atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Asiabi, Hamid [Department of Chemistry, Tarbiat Modares University, P.O. Box 14115-175, Tehran (Iran, Islamic Republic of); Yamini, Yadollah, E-mail: yyamini@modares.ac.ir [Department of Chemistry, Tarbiat Modares University, P.O. Box 14115-175, Tehran (Iran, Islamic Republic of); Seidi, Shahram [Department of Analytical Chemistry, Faculty of Chemistry, K.N. Toosi University of Technology, Tehran (Iran, Islamic Republic of); Shamsayei, Maryam; Safari, Meysam; Rezaei, Fatemeh [Department of Chemistry, Tarbiat Modares University, P.O. Box 14115-175, Tehran (Iran, Islamic Republic of)

    2016-05-30

    In this work, for the first time, a rapid, simple and sensitive microextraction procedure is demonstrated for the matrix separation, preconcentration and determination of inorganic selenium species in water samples using an electrochemically controlled in-tube solid phase microextraction (EC-in-tube SPME) followed by hydride generation atomic absorption spectrometry (HG-AAS). In this approach, in which EC-in-tube SPME and HG-AAS system were combined, the total analysis time, was decreased and the accuracy, repeatability and sensitivity were increased. In addition, to increases extraction efficiency, a novel nanostructured composite coating consisting of polypyrrole (PPy) doped with ethyleneglycol dimethacrylate (EGDMA) was prepared on the inner surface of a stainless-steel tube by a facile electrodeposition method. To evaluate the offered setup and the new PPy-EGDMA coating, it was used to extract inorganic selenium species in water samples. Extraction of inorganic selenium species was carried out by applying a positive potential through the inner surface of coated in-tube under flow conditions. Under the optimized conditions, selenium was detected in amounts as small as 4.0 parts per trillion. The method showed good linearity in the range of 0.012–200 ng mL{sup −1}, with coefficients of determination better than 0.9996. The intra- and inter-assay precisions (RSD%, n = 5) were in the range of 2.0–2.5% and 2.7–3.2%, respectively. The validated method was successfully applied for the analysis of inorganic selenium species in some water samples and satisfactory results were obtained. - Graphical abstract: An electrochemically controlled in-tube solid phase microextraction followed by hydride generation atomic absorption spectrometry was developed for extraction and determination ultra-trace amounts of Se in aqueous solutions. - Highlights: • A nanostructured composite coating consisting of PPy doped with EGDMA was prepared. • The coating was

  19. Fabrication of metal-organic frameworks and graphite oxide hybrid composites for solid-phase extraction and preconcentration of luteolin.

    Science.gov (United States)

    Wang, Yang; Wu, Yichun; Ge, Huali; Chen, Huanhuan; Ye, Guiqin; Hu, Xiaoya

    2014-05-01

    A novel solid-phase extraction sorbent, metal-organic frameworks and graphite oxide hybrid composite, was prepared by a solvothermal technique. The morphology and properties of the resultant material were examined by Fourier transform infrared spectroscopy, X-ray diffraction and field emission scanning electron microscopy. To evaluate the extraction performance of the resultant sorbent, luteolin was chosen as a model analyte. The extraction conditions were optimized. Based on these, a convenient and efficient solid-phase extraction procedure for the determination of luteolin was established and the subsequent quantification step was performed by square wave anodic stripping voltammetry. Under the optimal conditions, the oxidation current increased linearly with increasing the concentration of luteolin in the range of 5.0 × 10(-9)-5.0 × 10(-7)molL(-1) with a correlation coefficient of 0.9983 and a detection limit of 7.9 × 10(-10)molL(-1). The relative standard deviation of seven successive scans was 4.20% for 5.0 × 10(-8)molL(-1) luteolin. This work not only proposes a useful method for sample pretreatment, but also reveals the great potential of metal-organic frameworks based hybrid materials as an excellent sorbent in solid-phase extraction.

  20. Molecular imprinted polymer for solid-phase extraction of flavonol aglycones from Moringa oleifera extracts.

    Science.gov (United States)

    Pakade, Vusumzi; Cukrowska, Ewa; Lindahl, Sofia; Turner, Charlotta; Chimuka, Luke

    2013-02-01

    Molecular imprinted polymer produced using quercetin as the imprinting compound was applied for the extraction of flavonol aglycones (quercetin and kaempferol) from Moringa oleifera methanolic extracts obtained using heated reflux extraction method. Identification and quantification of these flavonols in the Moringa extracts was achieved using high performance liquid chromatography with ultra violet detection. Breakthrough volume and retention capacity of molecular imprinted polymer SPE was investigated using a mixture of myricetin, quercetin and kaempferol. The calculated theoretical number of plates was found to be 14, 50 and 8 for myricetin, quercetin and kaempferol, respectively. Calculated adsorption capacities were 2.0, 3.4 and 3.7 μmol/g for myricetin, quercetin and kaempferol, respectively. No myricetin was observed in Moringa methanol extracts. Recoveries of quercetin and kaempferol from Moringa methanol extracts of leaves and flowers ranged from 77 to 85% and 75 to 86%, respectively, demonstrating the feasibility of using the developed molecularly imprinted SPE method for quantitative clean-up of both of these flavonoids. Using heated reflux extraction combined with molecularly imprinted SPE, quercetin concentrations of 975 ± 58 and 845 ± 32 mg/kg were determined in Moringa leaves and flowers, respectively. However, the concentrations of kaempferol found in leaves and flowers were 2100 ± 176 and 2802 ± 157 mg/kg, respectively. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Bio-solid-phase extraction/tandem mass spectrometry for identification of bioactive compounds in mixtures.

    Science.gov (United States)

    Forsberg, Erica M; Brennan, John D

    2014-08-19

    We describe a two-step column-based bioassay method with tandem mass spectrometric detection for rapid identification of bioactive species in mixtures. The first step uses an immobilized enzyme reactor (IMER) column interfaced to an electrospray ionization mass spectrometer (ESI-MS) to identify mixtures containing bioactive compounds (i.e., enzyme inhibitors), while the second step uses bioselective solid-phase extraction (bioSPE) columns to isolate compounds from "hit" mixtures, which are then identified online by data-dependent ESI-MS. IMER columns were prepared by entrapment of adenosine deaminase (ADA) into sol-gel derived monolithic silica columns, and used to perform a primary IMER screen of mixtures prepared from a bioactive library, which resulted in four apparent hit compounds. Such columns did not provide sufficient binding site density to allow bioSPE, and thus a new column format was developed using ADA that was covalently immobilized to monolithic silica capillary columns, providing ∼500-fold more protein binding sites than were present in columns containing entrapped proteins. Using the covalently linked ADA columns, bioactive mixtures identified by IMER were infused until a maximum total ion current was achieved, followed by washing with a buffer to remove unbound compounds. A harsh wash with 3% acetic acid eluted the strongly bound ligands and the resulting peak triggered data dependent MS/MS to identify the ligand, showing that two of the apparent hits were true ADA inhibitors and demonstrating the ability of this method to rapidly identify bioactive compounds in mixtures.

  2. Matrix supported tailored polymer for solid phase extraction of fluoride from variety of aqueous streams

    Energy Technology Data Exchange (ETDEWEB)

    Thakur, Neha; Kumar, Sanjukta A.; Wagh, D.N. [Analytical Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Das, Sadananda; Pandey, Ashok K. [Radiochemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Kumar, Sangita D., E-mail: sangdk@barc.gov.in [Analytical Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India); Reddy, A.V.R. [Analytical Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India)

    2012-01-30

    Highlights: Black-Right-Pointing-Pointer Th complexed with poly (bis[2-(methacryloyloxy)-ethyl]phosphate) as tailored polymer membranes. Black-Right-Pointing-Pointer Membranes offered high capacity and selectivity for fluoride in aqueous media. Black-Right-Pointing-Pointer Quantitative uptake (80 {+-} 5%) of fluoride. Black-Right-Pointing-Pointer Fast sorption kinetics. Black-Right-Pointing-Pointer Reusability of polymer membranes. - Abstract: Fluoride related health hazards (fluorosis) are a major environmental problem in many regions of the world. It affects teeth; skeleton and its accumulation over a long period can lead to changes in the DNA structure. It is thus absolutely essential to bring down the fluoride levels to acceptable limits. Here, we present a new inorganic-organic hybrid polymer sorbent having tailored fixed-sites for fluoride sorption. The matrix supported poly (bis[2-(methacryloyloxy)-ethyl]phosphate) was prepared by photo-initiator induced graft-polymerization in fibrous and microporous (sheet) host poly(propylene) substrates. These substrates were conditioned for selective fluoride sorption by forming thorium complex with phosphate groups on bis[2-methacryloyloxy)-ethyl] phosphate (MEP). These tailored sorbents were studied for their selectivity towards fluoride in aqueous media having different chemical conditions. The fibrous sorbent was found to take up fluoride with a faster rate (15 min for Almost-Equal-To 76% sorption) than the sheet sorbent. But, the fluoride loading capacity of sheet sorbent (4320 mg kg{sup -1}), was higher than fibrous and any other sorbent reported in the literature so far. The sorbent developed in the present work was found to be reusable after desorption of fluoride using NaOH solution. It was tested for solid phase extraction of fluoride from natural water samples.

  3. Preparation and evaluation of a novel molecularly imprinted polymer coating for selective extraction of indomethacin from biological samples by electrochemically controlled in-tube solid phase microextraction

    Energy Technology Data Exchange (ETDEWEB)

    Asiabi, Hamid [Department of Chemistry, Tarbiat Modares University, P.O. Box 14115-175, Tehran (Iran, Islamic Republic of); Yamini, Yadollah, E-mail: yyamini@modares.ac.ir [Department of Chemistry, Tarbiat Modares University, P.O. Box 14115-175, Tehran (Iran, Islamic Republic of); Seidi, Shahram; Ghahramanifard, Fazel [Department of Analytical Chemistry, Faculty of Chemistry, K.N. Toosi University of Technology, Tehran (Iran, Islamic Republic of)

    2016-03-24

    In the present work, an automated on-line electrochemically controlled in-tube solid-phase microextraction (EC-in-tube SPME) coupled with HPLC-UV was developed for the selective extraction and preconcentration of indomethacin as a model analyte in biological samples. Applying an electrical potential can improve the extraction efficiency and provide more convenient manipulation of different properties of the extraction system including selectivity, clean-up, rate, and efficiency. For more enhancement of the selectivity and applicability of this method, a novel molecularly imprinted polymer coated tube was prepared and applied for extraction of indomethacin. For this purpose, nanostructured copolymer coating consisting of polypyrrole doped with ethylene glycol dimethacrylate was prepared on the inner surface of a stainless-steel tube by electrochemical synthesis. The characteristics and application of the tubes were investigated. Electron microscopy provided a cross linked porous surface and the average thickness of the MIP coating was 45 μm. Compared with the non-imprinted polymer coated tubes, the special selectivity for indomethacin was discovered with the molecularly imprinted coated tube. Moreover, stable and reproducible responses were obtained without being considerably influenced by interferences commonly existing in biological samples. Under the optimal conditions, the limits of detection were in the range of 0.07–2.0 μg L{sup −1} in different matrices. This method showed good linearity for indomethacin in the range of 0.1–200 μg L{sup −1}, with coefficients of determination better than 0.996. The inter- and intra-assay precisions (RSD%, n = 3) were respectively in the range of 3.5–8.4% and 2.3–7.6% at three concentration levels of 7, 70 and 150 μg L{sup −1}. The results showed that the proposed method can be successfully applied for selective analysis of indomethacin in biological samples. - Graphical abstract: An automated on-line

  4. Simultaneous determination of three banned psychiatric drugs in pig feed and tissue using solid-phase reactor on-line oxidizing and HPLC-fluorescence detection.

    Science.gov (United States)

    Qi, Liang; Duan, Li-Min; Sun, Xiao-Huan; Zhang, Jing; Zhang, Zhi-Qi

    2015-10-01

    The banned addition of psychiatric drugs such as phenothiazines to animal feed and foodstuffs increases the risk of human organ lesion. Phenothiazines usually exhibit weak native fluorescence and can be oxidized to strongly fluorescent compounds. In this study, a novel, sensitive and convenient method of HPLC-fluorescence detection based on post-column on-line oxidizing with lead dioxide solid-phase reactor has been developed for simultaneous determination of three banned psychotropic drugs, promethazine, chlorpromazine and thioridazine. Three compounds were successfully separated on an Agilent TC-C18 column with mobile phase of acetonitrile (A) and water (B), both containing 0.5% (v/v) formic acid. A gradient elution was programmed and fluorimetric detection was performed at λex /λem of 332/373 nm for promethazine, 340/380 nm for chlorpromazine and 352/432 nm for thioridazine. The calibration graphs gave good linearity over the concentration ranges of 30.0-4976.4 µg/L for promethazine, 2.0-2153.2 µg/L for chlorpromazine, and 15.0-3088.0 µg/L for thioridazine, and correlation coefficients (r) were ≥0.995. The method was applied to the determination of phenothiazines in pig feed and pig tissue, and the average spiked recoveries were in the range 69.1-115.4%.

  5. Selective solid-phase extraction of a triterpene acid from a plant extract by molecularly imprinted polymer.

    Science.gov (United States)

    Claude, Bérengère; Morin, Philippe; Lafosse, Michel; Belmont, Anne-Sophie; Haupt, Karsten

    2008-04-15

    A molecularly imprinted polymer (MIP) has been prepared by a thermal polymerisation method using methacrylic acid as functional monomer, ethylene glycol dimethacrylate as cross-linking agent, chloroform as porogenic solvent and an oleanane triterpene compound (18-beta-glycyrrhetinic acid) as imprinted molecule (template). Equilibrium ligand binding experiments were done to assess the performance of the MIP relative to non-imprinted polymer (NIP). After optimisation of SPE protocol (CHCl3 as washing solvent and MeOH as elution solvent), successful imprinting was confirmed by comparison of the recoveries between NIP (5%) and MIP (97%) cartridges. The binding capacity of the MIP for 18-beta-glycyrrhetinic acid was determined to be 0.94 mg g(-1). Four structurally related oleanane triterpenes (18-alpha-glycyrrhetinic acid, oleanolic acid, echinocystic acid, erythrodiol) were selected to assess the MIP selectivity. Experimental data illustrated the influence of functional groups on the triterpene skeleton. The MIP was applied to the solid-phase extraction of triterpenoids from a plant extract prior HPLC analysis. However, CHCl3 was replaced by ACN during the washing step in order to suppress non-specific interactions due to polar matrix components. A selective extraction of 18-beta-glycyrrhetinic acid from hydrolyzed extract of liquorice roots was achieved with a good extraction yield (98%).

  6. Liquid-Liquid Extraction and Solid Phase Extraction for Urinary Organic Acids: A Comparative Study from a Resource Constraint Setting.

    Science.gov (United States)

    Kumari, Chandrawati; Varughese, Bijo; Ramji, Siddarth; Kapoor, Seema

    2016-10-01

    Pre analytical process of extraction for accurate detection of organic acids is a crucial step in diagnosis of organic acidemias by GCMS analysis. This process is accomplished either by solid phase extraction (SPE) or by liquid-liquid extraction (LLE). Both extraction procedures are used in different metabolic laboratories all over the world. In this study we compared these two extraction procedures in respect of precision, accuracy, percent recovery of metabolites, number of metabolites isolated, time and cost in a resource constraint setup. We observed that the mean recovery from SPE was 84.1 % and by LLE it was 77.4 % (p value <0.05). Moreover, the average number of metabolites isolated by SPE and LLE was 161.8 ± 18.6 and 140.1 ± 20.4 respectively. The processing cost of LLE was economical. In a cost constraint setting using LLE may be the practical option if used for organic acid analysis.

  7. Extraction and analysis of polycyclic aromatic hydrocarbons (PAHs) by solid phase micro-extraction/supercritical fluid chromatography (SPME/SFC)

    Energy Technology Data Exchange (ETDEWEB)

    Lesellier, E. [Institut Universitaire de Technologie, (LETIAM), 91 - Orsay (France)

    1999-05-01

    Solid phase micro-extraction (SPME) is a clean and simple pre-concentration method. Previously used for trace analysis of volatile compounds, the use of SPME was extended to non volatile molecules with the development of an SPME/HPLC interface. This new interface allows the extraction and the analysis of high molecular weight compounds found in aqueous samples. Since superficial fluid chromatography is particularly well suited for analysis of complex mixtures containing non volatile compounds, the feasibility of coupling SPME and SFC has been investigated and applied to PAHs. Several points have been studied: behavior of interface and of fiber to superficial fluid and high pressure required by the analytical method; kind of the compounds transfer from the fiber to the analytical column; relation between the nature of the fibers and the quantity of extracted compounds; effect of salt addition. The results show that the SPME/SFC technic may be used for extraction and analysis of PAHs, since the quantity of extracted compounds reach 30 %. (author) 17 refs.

  8. Direct Sampling and Analysis from Solid Phase Extraction Cards using an Automated Liquid Extraction Surface Analysis Nanoelectrospray Mass Spectrometry System

    Energy Technology Data Exchange (ETDEWEB)

    Walworth, Matthew J [ORNL; ElNaggar, Mariam S [ORNL; Stankovich, Joseph J [ORNL; WitkowskiII, Charles E. [Protein Discovery, Inc.; Norris, Jeremy L [ORNL; Van Berkel, Gary J [ORNL

    2011-01-01

    Direct liquid extraction based surface sampling, a technique previously demonstrated with continuous flow and autonomous pipette liquid microjunction surface sampling probes, has recently been implemented as the Liquid Extraction Surface Analysis (LESA) mode on the commercially available Advion NanoMate chip-based infusion nanoelectrospray ionization system. In the present paper, the LESA mode was applied to the analysis of 96-well format custom solid phase extraction (SPE) cards, with each well consisting of either a 1 or 2 mm diameter monolithic hydrophobic stationary phase. These substrate wells were conditioned, loaded with either single or multi-component aqueous mixtures, and read out using the LESA mode of a TriVersa NanoMate or a Nanomate 100 coupled to an ABI/Sciex 4000QTRAPTM hybrid triple quadrupole/linear ion trap mass spectrometer and a Thermo LTQ XL linear ion trap mass spectrometer. Extraction conditions, including extraction/nanoESI solvent composition, volume, and dwell times, were optimized in the analysis of targeted compounds. Limit of detection and quantitation as well as analysis reproducibility figures of merit were measured. Calibration data was obtained for propranolol using a deuterated internal standard which demonstrated linearity and reproducibility. A 10x increase in signal and cleanup of micromolar Angiotensin II from a concentrated salt solution was demonstrated. Additionally, a multicomponent herbicide mixture at ppb concentration levels was analyzed using MS3 spectra for compound identification in the presence of isobaric interferences.

  9. Molecularly Imprinted Polymer for Solid-Phase Extraction of Ecteinascidin 743 from Sea Squirt%Molecularly Imprinted Polymer for Solid-Phase Extraction of Ecteinascidin 743 from Sea Squirt

    Institute of Scientific and Technical Information of China (English)

    田明磊; 李圣男; 卢敬吴

    2012-01-01

    Ecteinascidin 743 from sea squirt is one of the most original anti-tumoral activity compounds, as proven by the Natural Cancer Institute. Ecteinascidin 743 could be obtained with traditional liquid extraction, but it should be purified and separated from the extract. A molecularly imprinted solid-phase extraction procedure was developed for the selective separation. Ecteinascidin 743 was used as the template and the polymer was synthesized in a methanol environment. Water and n-hexane as the washing solvents can eliminate most of the interference. Good linearity and low relative standard deviations (less than 4.39%)justify its continuing development.

  10. Selective solid-phase extraction using molecular imprinted polymer sorbent for the analysis of florfenicol in food samples.

    Science.gov (United States)

    Sadeghi, Susan; Jahani, Moslem

    2013-11-15

    A molecularly imprinted polymer (MIP) for the selective solid phase extraction (SPE) of florfenicol (FF) was prepared using FF as template and 4-vinyl pyridine (4-VP) as functional monomer. For comparison, non-imprinted polymer (NIP) was synthesized in the absence of FF. The synthesized polymers were characterised by infrared spectroscopy (IR), scanning electron microscopy (SEM), thermogravimetry analysis (TGA) and differential thermal analysis (DTA). A molecularly imprinted solid phase extraction (MISPE) procedure was performed in column method by spectrophotometry detection technique. The prepared FF-MIP showed higher adsorption capacity than the non-imprinted polymer (NIP) and the maximum static adsorption capacities of FF on the MIP and the NIP were 4.32 and 2.88mgg(-1), respectively. Kinetics of the adsorption was fast and the adsorption equilibrium was achieved in 30min. The accuracy of the developed method was satisfactory for determination of FF in fish, chicken meat and honey samples.

  11. On-site solid-phase extraction and application to in situ preconcentration of heavy metals in surface water.

    Science.gov (United States)

    Jiao, Fang; Gao, Hong-Wen

    2013-01-01

    An on-site solid-phase extraction, consisting of the sorption, the separation and the elution function units, was designed for in situ preconcentration of heavy metals ions. The D401 resin powder was employed as sorbent to capture Pb(2+), Cu(2+), Zn(2+), Cd(2+), Co(2+), and Ni(2+), and then they desorbed with 2 mol/L nitric acid as eluent. Under the optimized conditions, these heavy metals ions in West Lake, Taihu Lake, and Yangtze River of China were captured and then determined by ICP-OES with the recovery of 92.5% to 111.5%. The on-site solid-phase extraction achieved a quick preconcentration of heavy metals to avoid the transport and storage of a large volume water sample. It is suitable for in situ monitoring of water quality in mountains, tablelands or other remote areas.

  12. Solid phase extraction of lactic acid from fermentation broth by anion-exchangeable silica confined ionic liquids.

    Science.gov (United States)

    Bi, Wentao; Zhou, Jun; Row, Kyung Ho

    2011-01-15

    Three anion-exchangeable, silica-confined ionic liquids were synthesized for solid phase extraction of lactic acid from fermentation broth, followed by high-performance liquid chromatography coupled to ultraviolet detection. By comparing the adsorption isotherms of lactic acid on different silica-confined ionic liquids, interactions between the lactic acid and sorbents were investigated. The adsorbed amounts were then fitted into different adsorption isotherm equations; finally, the Langmuir equation was selected. Then the imidazolium silica with the highest adsorption capacity of lactic acid was packed into a cartridge for solid phase extraction. The loading volume of the cartridge was optimized by the Langmuir equation and geometry. After washing with distilled water and eluting with 0.25 mol L(-1) of an HCl solution, the lactic acid was separated from interference with a recovery yield of 91.9%. Furthermore, this kind of anion-exchangeable material exhibited potential for industrial applications and separation of other anionic bioactive compounds.

  13. Optimization of the extraction conditions of the volatile compounds from chili peppers by headspace solid phase micro-extraction.

    Science.gov (United States)

    Junior, Stanislau Bogusz; de Marchi Tavares de Melo, Arlete; Zini, Cláudia Alcaraz; Godoy, Helena Teixeira

    2011-05-27

    A method involving headspace-solid phase micro-extraction (HS-SPME), gas chromatography with flame ionization detection (GC-FID) and gas chromatography with mass spectrometry (GC-MS) was developed and optimized to investigate the volatile composition of Capsicum chili peppers. Five SPME fibers were tested for extraction: carboxen/polydimethylsiloxane (CAR/PDMS-75μm), polydimethylsiloxane (PDMS-100μm), divinylbenzene/polydimethylsiloxane (DVB/PDMS-65μm), carbowax/divinylbenzene (CW/DVB-70μm), and divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS-50/30μm), the last of which was shown to be the most efficient fiber to trap the volatile compounds. Optimization of the extraction conditions was carried out using multivariate strategies such as factorial design and response surface methodology. Eighty three compounds were identified by GC-MS when using the optimized extraction conditions, the majority of which were esters. Copyright © 2011 Elsevier B.V. All rights reserved.

  14. Extraction and determination of trace amounts of chlorpromazine in biological fluids using magnetic solid phase extraction followed by HPLC

    Directory of Open Access Journals (Sweden)

    Yadollah Yamini

    2014-08-01

    Full Text Available A simple, rapid and sensitive method termed as magnetic solid phase extraction (MSPE combined with high-performance liquid chromatography-ultraviolet detector (HPLC-UV has been proposed for the determination of trace amounts of chlorpromazine (CPZ in water, urine and plasma samples. The separation and determination was performed on a C18 column under the optimal chromatographic conditions. Several factors influencing the extraction efficiency of CPZ, such as pH, surfactant and adsorbent amounts, ionic strength, extraction time, sample volume and desorption conditions, were studied and optimized. Under the optimal MSPE conditions, the extraction percentage of CPZ was 74%, 27% and 16% in water, urine and plasma samples, respectively. The limits of detection (LODs of the proposed approach were 0.1, 5.0 and 10 ng/mL in water, urine and plasma samples, respectively. The relative standard deviations (RSDs based on five replicate determinations at 10 ng/mL level of CPZ was 1.2%. Good linear behaviors over the investigated concentration ranges (0.25–300 ng/mL with good coefficient of determination, R2>0.9998, were obtained. Good spike recoveries with relative errors less than 9.0% were obtained when applying the proposed method to water, urine and plasma samples.

  15. Tropical peat as a versatile material for solid-phase extraction of pesticides from medicinal plant Cordia salicifolia

    OpenAIRE

    Carvalho,Pedro H. V. de; Amanda M. D. de Jesus; Prata,Vanessa M.; Bezerra,Débora S. S.; Romão, Luciane P. C.; Navickiene, Sandro

    2010-01-01

    Natural peat was tested for solid-phase extraction of acephate, chlorpropham, pirimicarb, bifenthrin, tetradifon and phosalone from the medicinal plant Cordia salicifolia, using gas chromatography-mass spectrometry with selected ion monitoring (GC/MS, SIM). Considering that there are no Brazilian regulations concerning maximum permissible pesticide residue concentrations in medicinal herbs, recovery experiments were carried out (three replicates) at two arbitrary fortification levels (0.5 and...

  16. Imprinted magnetic graphene oxide for the mini-solid phase extraction of Eu (III) from coal mine area

    Science.gov (United States)

    Patra, Santanu; Roy, Ekta; Madhuri, Rashmi; Sharma, Prashant K.

    2017-05-01

    The present work represents the preparation of imprinted magnetic reduced graphene oxide and applied it for the selective removal of Eu (III) from local coal mines area. A simple solid phase extraction method was used for this purpose. The material shows a very high adsorption as well as removal efficiency towards Eu (III), which suggest that the material have potential to be used in future for their real time applications in removal of Eu (III) from complex matrices.

  17. A novel dispersive micro solid phase extraction using zein nanoparticles as the sorbent combined with headspace solid phase micro-extraction to determine chlorophenols in water and honey samples by GC-ECD.

    Science.gov (United States)

    Farhadi, Khalil; Matin, Amir Abbas; Amanzadeh, Hatam; Biparva, Pourya; Tajik, Hossein; Farshid, Amir Abbas; Pirkharrati, Hossein

    2014-10-01

    This study presents a new technique, dispersive micro solid phase extraction (DMSPE) combined with headspace solid phase micro-extraction (HS-SPME) for extraction and determination of chlorophenols (CPs) in water and honey samples using a Gas Chromatography-Electron Capture Detector (GC-ECD). Zein nanoparticles were made by liquid-liquid dispersion and applied for the first time as the sorbent phase in DMSPE. In the proposed DMSPE-HS-SPME method, 1% w/v of ethanolic zein solution was added to an aqueous sample and then a dose of the in-situ generated zein nanoparticles was applied to a pre-concentration of target analytes. Thermal desorption of analytes was performed after the isolating sorbent phase, and then HS-SPME was applied for enrichment prior to introducing to gas chromatography. All the important parameters influencing efficiency of the extraction process such effects of salt, pH, sorbent concentration, temperature, sorbent solution volume in DMSPE procedure, extraction temperature, extraction time, desorption temperature and time in the HS-SPME procedure were investigated and optimized. Results showed that under optimum extraction conditions, detection limits (signal to noise ratio=3) were in the range of 0.08-0.6 ng mL(-1) and evaluations for relative standard deviations (RSDs %) were between 6.62% and 8.36%.

  18. Single step determination of PCB 126 and 153 in rat tissues by using solid phase microextraction/gas chromatography-mass spectrometry: Comparison with solid phase extraction and liquid/liquid extraction.

    Science.gov (United States)

    Poli, Diana; Caglieri, Andrea; Goldoni, Matteo; Castoldi, Anna F; Coccini, Teresa; Roda, Elisa; Vitalone, Annabella; Ceccatelli, Sandra; Mutti, Antonio

    2009-03-15

    A simple and reliable solid phase microextraction/gas chromatography-mass spectrometry (SPME/GC-MS) method was developed for the single-step determination of PCBs 126 and 153 in rat brain and serum, using liquid/liquid and solid phase extraction (SPE) as reference techniques. The multi-factor categorical experimental design used to study simultaneously the main parameters and their interactions affecting the efficiency of the method, showed that the use of an 85mum PA exposed at 100 degrees C for 40min was the optimum sampling condition for both PCBs. SPME was then validated by studying its linear dynamic (over two orders of magnitude), limits of detection (brain: 2ng/g, serum: 0.2ng/g) and analytical precision that was within 9% for SPME in both brain and serum. Finally, the method was used to determine the brain and blood target dose in mothers and pups after oral exposure of the mothers.

  19. Design of the extraction process for terpenes and other volatiles from allspice by solid-phase microextraction and hydrodistillation.

    Science.gov (United States)

    Bajer, Tomáš; Ligor, Magdalena; Ligor, Tomasz; Buszewski, Bogusław

    2016-02-01

    Methods for the separation and determination of terpenes (mono- and sesqui-) and phenylpropanoids such as eugenol and methyleugenol from samples of allspice berries have been developed. Chromatographic analyses of isolated groups of compounds were carried out by means of gas chromatography coupled with mass spectrometry. A comparison of various types of solid-phase microextraction fibers was performed. The highest yields of terpenes were extracted by polydimethylsiloxane and divinylbenzene/Carboxen/polydimethylsiloxane fibers (almost the same for these two fibers), approximately twice as much as by Carbowax/divinylbenzene fiber. The highest amounts of monoterpenes were extracted by divinylbenzene/Carboxen/polydimethylsiloxane fiber, and the highest amounts of sesquiterpenes were extracted by polydimethylsiloxane fiber. Moreover, the effect of water addition on extraction yields as well as time and temperature of extraction were tested. Aroma profiles of extracts obtained by solid-phase microextraction and essential oil obtained by hydrodistillation of allspice berries were compared. The aroma profile of the divinylbenzene/Carboxen/polydimethylsiloxane fiber extract was similar to the aroma profile of essential oil. Particular characteristics of volatile allspice matters were presented. The linear retention indices for each compound were calculated.

  20. Graphene-Based Materials as Solid Phase Extraction Sorbent for Trace Metal Ions, Organic Compounds, and Biological Sample Preparation.

    Science.gov (United States)

    Ibrahim, Wan Aini Wan; Nodeh, Hamid Rashidi; Sanagi, Mohd Marsin

    2016-07-03

    Graphene is a new carbon-based material that is of interest in separation science. Graphene has extraordinary properties including nano size, high surface area, thermal and chemical stability, and excellent adsorption affinity to pollutants. Its adsorption mechanisms are through non-covalent interactions (π-π stacking, electrostatic interactions, and H-bonding) for organic compounds and covalent interactions for metal ions. These properties have led to graphene-based material becoming a desirable adsorbent in a popular sample preparation technique known as solid phase extraction (SPE). Numerous studies have been published on graphene applications in recent years, but few review papers have focused on its applications in analytical chemistry. This article focuses on recent preconcentration of trace elements, organic compounds, and biological species using SPE-based graphene, graphene oxide, and their modified forms. Solid phase microextraction and micro SPE (µSPE) methods based on graphene are discussed.

  1. Determination of Trace Amount of Polycyclic Aromatic Hydrocarbons in Urban Sewage by Solid-phase Extraction Coupled with High Performance Liquid Chromatograph

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    [Method] This study aimed to determine trace amount of polycyclic aromatic hydrocarbons(PAHs) in urban sewage by using solid-phase extraction(SPE) coupled with high performance liquid chromatograph(HPLC).[Method] From the aspects of solid-phase extraction column,elution solvent,elution volume,elution speed and so forth,the test conditions of SPE-HPLC method were optimized,and trace amount of PAHs in urban sewage was determined.[Result] The optimized solid-phase extraction conditions were SUPELCLEAN LC-18 so...

  2. Cleanup and analysis of sugar phosphates in biological extracts by using solid phase extraction and anion-exchange chromatography with pulsed amperometric detection

    DEFF Research Database (Denmark)

    Smith, Hans Peter; Cohen, A.; Buttler, T.

    1998-01-01

    A cleanup method based on anion-exchange solid-phase extraction (SPE) was developed to render biological extracts suitable for the analysis of hexose phosphates with a modified anion-exchange chromatography method and pulsed amperometric detection. The method was applied to cell extracts of Sacch......A cleanup method based on anion-exchange solid-phase extraction (SPE) was developed to render biological extracts suitable for the analysis of hexose phosphates with a modified anion-exchange chromatography method and pulsed amperometric detection. The method was applied to cell extracts...... of Saccharomyces cerevisiae obtained by using cold methanol as quenching agent and chloroform as extraction solvent. It was shown that pretreatment of the cell extract with SPE markedly improved the quality of the liquid chromatography analysis with recoveries of the sugar phosphates close to 100%. Furthermore...

  3. Automated on-line in-tube solid-phase microextraction-assisted derivatization coupled to liquid chromatography for quantifying residual dimethylamine in cationic polymers.

    Science.gov (United States)

    Prieto-Blanco, M C; Cháfer-Pericás, C; López-Mahía, P; Campíns-Falcó, P

    2008-04-25

    A method for the analysis of dimethylamine (DMA) by automated in-tube solid-phase microextraction (IT-SPME)-supported chemical derivatization coupled with high-performance liquid chromatography was developed. Extraction, derivatization and desorption were studied by using a capillary coated with 95% polydimethylsiloxane and 5% polydiphenylsiloxane. Solution derivatization and automated IT-SPME derivatization using 9-fluorenylmethyl chloroformate (FMOC) were compared. The proposed procedure provided adequate linearity, accuracy and precision in the 0.2-2.0 microg/mL concentration interval, and the limit of detection (LOD) was 50 ng/mL. The main advantages of the proposed procedure are: (i) no off-line sample manipulation, (ii) rapidity, as the total analysis time is about 10 min, (iii) specificity for the samples assayed, (iv) minimal consumption of FMOC reagent and (v) minimal residues. Therefore, the proposed method is an environmental-friendly and cost-effective alternative for the control of residual DMA in polymeric cationic surfactants used like flocculants in water treatment.

  4. Molecularly imprinted solid-phase extraction monolithic capillary column for selective extraction and sensitive determination of safranine T in wolfberry.

    Science.gov (United States)

    Su, Zihao; Zhai, Haiyun; Chen, Zuanguang; Zhou, Qing; Li, Jiangmei; Liu, Zhenping

    2014-02-01

    A method was developed to sensitively determine safranine T in wolfberry by molecularly imprinted solid-phase extraction (MISPE) coupled with high-performance liquid chromatography and laser-induced fluorescence detection (HPLC-LIF). The MISPE capillary monolithic column was prepared by water-bath in situ polymerization, using safranine T, methacrylic acid (MAA), and ethylene dimethacrylate (EDMA) as template, functional monomer, and cross-linker, respectively. The properties of the homemade MISPE capillary monolithic column, including capacity and specificity, were investigated under optimized conditions and the morphologies of inner polymers were characterized by scanning electron microscopy (SEM). The mean recoveries of safranine T in wolfberry ranged from 91.2 % to 92.9 % and the intraday and interday relative standard deviation (RSD) values all ranged from 3.4 % to 4.2 %. Good linearity was obtained over 0.001-1.0 μg mL(-1) (r = 0.9999) with a detection limit (S/N = 3) of 0.4 ng g(-1). Under the selected conditions, enrichment factors of over 90-fold were obtained and the extraction on the monolithic column effectively cleaned up the wolfberry matrix. The results demonstrated that the proposed MISPE-HPLC-LIF method could be applied to sensitively determine safranine T in wolfberry.

  5. Polyaniline/Graphene Nanocomposite as a Promising Sorbent for Dispersive Solid Phase Extraction of Avermectins from Citrus Fruit Juice

    Directory of Open Access Journals (Sweden)

    Faezeh Khalilian

    2017-06-01

    Full Text Available A solid phase extraction sorbent based on polyaniline/graphene nanocomposite is presented. The structure and morphology of synthesized nanocomposite were investigated by Fourier transform infrared spectroscopy, field emission scanning electron microscopy, X-ray diffraction and thermal gravimetric analysis. The dispersive solid phase extraction was employed to the isolation and preconcentration of avermectins insecticide (mixture of B1a and B1b. The extraction procedure was investigated by high performance liquid chromatography-UV detection. The sorbent demonstrated a favorable analytical performance for avermectins detection with reasonable linear ranges (1.5-1000 μg L-1 and 5.0-1000 μg L-1 for B1a and B1b in order and acceptable detection limits (0.5 μg L-1 for B1a and 2.5 μg L-1 for B1b under optimized conditions. The extraction efficiency of polyaniline/graphene nanocomposite in the extraction of avermectins was compared with graphene, polyaniline, carbon nanotube and C18 sorbents. Moreover, the applicability of proposed method was assessed for the extraction of analyte from citrus fruit juice.

  6. Magnetic mixed hemimicelles solid-phase extraction of xanthohumol in beer coupled with high-performance liquid chromatography determination.

    Science.gov (United States)

    Ding, Jie; Zhao, Qi; Sun, Lei; Ding, Lan; Ren, Nanqi

    2011-06-01

    In this study, silica-coated magnetic nanoparticles (Fe(3)O(4)/SiO(2) NPs) modified by cetyltrimethylammonium bromide (CTAB) were synthesized. They were successfully applied for extraction of xanthohumol in beer based on magnetic mixed hemimicelles solid-phase extraction (MMHSPE) coupled with high-performance liquid chromatography-ultraviolet determination. The main factors influencing the extraction efficiency including the surfactant amount, the beer pH, the extraction time, the desorption condition and the maximum extraction beer volume were optimized. Under the optimized conditions, a concentration factor of 60 was achieved by extracting 120 mL beer sample using MMHSPE and the detection limit of xanthohumol is 0.0006 mg/L. The proposed method was successfully applied for determination of xanthohumol in various beer samples with the xanthohumol contents in the range of 0.031-0.567 mg/L. The satisfactory recoveries (90-103%) were obtained in analyzing spiked beer samples.

  7. Liquid-solid extraction coupled with magnetic solid-phase extraction for determination of pyrethroid residues in vegetable samples by ultra fast liquid chromatography.

    Science.gov (United States)

    Jiang, Chunzhu; Sun, Ying; Yu, Xi; Gao, Yan; Zhang, Lei; Wang, Yuanpeng; Zhang, Hanqi; Song, Daqian

    2013-09-30

    In this study, liquid-solid extraction coupled with magnetic solid-phase extraction was successfully developed for the extraction of pyrethroid residues in vegetable samples. The analytes were determined by ultra fast liquid chromatography. The pyrethroids were extracted by liquid-solid extraction and then adsorbed onto magnetic adsorbent. Magnetic adsorbent, C18-functionalized ultrafine magnetic silica nanoparticles, was synthesized by chemical coprecipitation, silanization and alkylation. The analytes adsorbed onto the magnetic adsorbent can be simply and rapidly isolated from sample solution with a strong magnet on the bottom of the extraction vessel. The extraction parameters, such as liquid-solid extraction solvent, liquid-solid extraction time, the amount of magnetic adsorbent, magnetic solid-phase extraction time and magnetic solid-phase extraction desorption solvent, were optimized to improve the extraction efficiency. The analytical performances of this method, including linear range, detection limit, precision, and recovery were evaluated. The limits of detection for pyrethroid were between 0.63 and 1.2 ng g(-1). Recoveries obtained by analyzing the four spiked vegetable samples were between 76.0% and 99.5%. The results showed that the present method was a simple, accurate and high efficient approach for the determination of pyrethroids in the vegetable samples.

  8. Acetonitrile extraction and dual-layer solid phase extraction clean-up for pesticide residue analysis in propolis.

    Science.gov (United States)

    Oellig, Claudia

    2016-05-06

    Propolis is a very complex mixture of substances that is produced by honey bees and is known to be a rather challenging matrix for residue analysis. Besides resins, flavonoids and phenols, high amount of wax is co-extracted resulting in immense matrix effects. Therefore a suitable clean-up is crucial and indispensable. In this study, a reliable solid phase extraction (SPE) clean-up was developed for pesticide residue analysis in propolis. The clean-up success was quickly and easily monitored by high-performance thin-layer chromatography with different detection possibilities. The final method consists of the extraction of propolis with acetonitrile according to the QuEChERS method followed by an effective extract purification on dual-layer SPE cartridges with spherical hydrophobic polystyrene-divinylbenzene resin/primary secondary amine as sorbent and a mixture of toluene/acetone (95:5, v/v) for elution. Besides fat-soluble components like waxes, flavonoids, and terpenoids, more polar compounds like organic acids, fatty acids, sugars and anthocyanins were also removed to large extent. Method performance was assessed by recovery experiments at spiking levels of 0.5 and 1mg/kg (n=5) for fourteen pesticides that are relevant for propolis. Mean recoveries determined by HPLC-MS against solvent standards were between 40 and 101%, while calculation against matrix-matched standards provided recoveries of 79-104%. Precision of recovery, assessed by relative standard deviations, were below 9%. Thus, the developed dual-layer SPE clean-up enables the reliable pesticide residue analysis in propolis and provides a suitable alternative to time-consuming clean-up procedures proposed in literature.

  9. Evaluation of a Cyclodextrin-silica Hybrid Microporous Composite for the Solid-phase Extraction of Polycyclic Aromatic Hydrocarbons.

    Science.gov (United States)

    Soler-Seguí, Salomé; Belenguer-Sapiña, Carolinakn-Aut-Sei; Amorós, Pedro; Mauri-Aucejo, Adela

    2016-01-01

    Solid-phase extraction (SPE) coupled with high-performance liquid chromatography (HPLC) with fluorescence detection were employed to determine trace polycyclic aromatic hydrocarbons in water samples. In this way, the use of cartridges containing cyclodextrin-silica hybrid microporous solid phases was proposed. The experimental results indicated that the method provided relative standard deviations of below 15% and detection limits recorded were 12, 1.2, 12, 38, 4, 6 and 4 ng L(-1) for benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[g,h,i]perylene, indeno[1,2,3]pyrene, benzo[a]pyrene, dibenzo[a,h]anthracene and benzo[a]anthracene, respectively. Moreover, the method was successfully applied for the determination of these organic compounds in water samples, where they were found to be in the 7 to 580 ng L(-1) range. It can be concluded that the major advantages of cyclodextrin-silica hybrid microporous solid phases are that they reduce the consumption and the toxicity of the solvent and the time consumption of the sample treatment step.

  10. Monitoring of N-methyl carbamate pesticide residues in water using hollow fibre supported liquid membrane and solid phase extraction

    Science.gov (United States)

    Msagati, Titus A. M.; Mamba, Bhekie B.

    The aim of this work was to develop a method for the determination of N-methyl carbamates in water involving hollow fibre supported liquid membrane (HFSLM) and solid phase extraction (SPE) as sample preparation methods. Four N-methyl carbamate pesticides, aldicarb, carbaryl, carbofuran and methiocarb sulfoxide, were simultaneously extracted and analysed by a liquid chromatograph with a diode array detector (LC-UV/DAD) and a liquid chromatograph coupled to a ion trap quadrupole mass spectrometer (LC-ESI-MS). The high performance liquid chromatography (HPLC) separation of carabamate extracts was performed on a C18 column with water-acetonitrile as the mobile phase. The mass spectrometry analyses were carried out in the positive mode, operating under both the selected ion monitoring (SIM) and full scan modes. The solid phase recoveries of the extracts ranged between 8% and 98%, with aldicarb having the highest recoveries, followed by carbaryl, carbofuran and methiocarb had the lowest recovery. The HFSLM recovery ranged between 8% and 58% and the order of recovery was similar to the SPE trend. Factors controlling the efficiency of the HFSLM extraction such as sample pH, stripping phase pH, enrichment time, stirring speed as well as organic solvent used for entrapment of analytes, were optimised to achieve the highest enrichment factors.

  11. Aptamer-functionalized Fe3 O4 magnetic nanoparticles as a solid-phase extraction adsorbent for the selective extraction of berberine from Cortex phellodendri.

    Science.gov (United States)

    Jiang, Ling-Feng; Chen, Bo-Cheng; Chen, Ben; Li, Xue-Jian; Liao, Hai-Lin; Zhang, Wen-Yan; Wu, Lin

    2017-07-01

    The extraction adsorbent was fabricated by immobilizing the highly specific recognition and binding of aptamer onto the surface of Fe3 O4 magnetic nanoparticles, which not only acted as recognition elements to recognize and capture the target molecule berberine from the extract of Cortex phellodendri, but also could favor the rapid separation and purification of the bound berberine by using an external magnet. The developed solid-phase extraction method in this work was useful for the selective extraction and determination of berberine in Cortex phellodendri extracts. Various conditions such as the amount of aptamer-functionalized Fe3 O4 magnetic nanoparticles, extraction time, temperature, pH value, Mg(2+) concentration, elution time and solvent were optimized for the solid-phase extraction of berberine. Under optimal conditions, the purity of berberine extracted from Cortex phellodendri was as high as 98.7% compared with that of 4.85% in the extract, indicating that aptamer-functionalized Fe3 O4 magnetic nanoparticles-based solid-phase extraction method was very effective for berberine enrichment and separation from a complex herb extract. The applicability and reliability of the developed solid-phase extraction method were demonstrated by separating berberine from nine different concentrations of one Cortex phellodendri extract. The relative recoveries of the spiked solutions of all the samples were between 95.4 and 111.3%, with relative standard deviations ranging between 0.57 and 1.85%. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. EPA Method 525.3 - Determination of Semivolatile Organic Chemicals in Drinking Water by Solid Phase Extraction and Capillary Column Gas Chromatography/Mass Spectrometry (GC/MS)

    Science.gov (United States)

    Method 525.3 is an analytical method that uses solid phase extraction (SPE) and gas chromatography/mass spectrometry (GC/MS) for the identification and quantitation of 125 selected semi-volatile organic chemicals in drinking water.

  13. Preconcentration and determination of cadmium in water and food samples by in situ surfactant-based solid-phase extraction and flame atomic absorption spectrometry

    National Research Council Canada - National Science Library

    Jamali, Mohammad Reza; Boromandi, Afsaneh

    2014-01-01

    In situ surfactant-based solid-phase extraction (ISS-SPE) is proposed as a preconcentration procedure for the determination of cadmium in water and food samples by flame atomic absorption spectrometry...

  14. Solid-phase extraction of flavonoids in honey samples using carbamate-embedded triacontyl-modified silica sorbent.

    Science.gov (United States)

    Liu, Houmei; Zhang, Mingliang; Guo, Yong; Qiu, Hongdeng

    2016-08-01

    In this study, carbamate-embedded triacontyl-modified silica (Sil-CBM-C30) is successfully prepared and used as an efficient sorbent for solid-phase extraction. The extraction performance of the resultant sorbent is evaluated with five flavonoids including myricetin, quercetin, luteolin, kaempferol and isorhamnetin. Main parameters, which affect extraction efficiencies, are carefully investigated and optimized. Comparative experiments between Sil-CBM-C30 and commercial C18 sorbents indicate that the extraction efficiencies of the former one surpass the latter one. The modification of carbamate-embedded triacontyl group on surface of silica causes analytes extracted by hydrophobic, hydrogen bonding and π-π interactions. Under optimal conditions, good linearities and satisfied LODs and LOQs are achieved. The SPE-HPLC-DAD method is successfully developed and applied for the honey sample analysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. Increasing the large scale feasibility of a solid phase extraction procedure for the recovery of natural antioxidants from olive mill wastewaters

    OpenAIRE

    Scoma, Alberto; Pintucci, Cristina; Bertin, Lorenzo; Carlozzi, Pietro; Fava, Fabio

    2012-01-01

    The present investigation was focused on improving the feasibility of large scale applications of a solid phase extraction (SPE) procedure dedicated to the recovery of polyphenols from olive mill wastewaters (OMWs). To this aim, a previously developed SPE procedure was optimized in terms of contact time without negatively affecting the overall process productivity. The possibility of regenerating and recycling both the solid phase (Amberlite XAD16 non-polar resin) and the extraction solvent (...

  16. [Rapid determination of six preservative residues in fruits and vegetables by high performance liquid chromatography using dispersive solid phase extraction].

    Science.gov (United States)

    Lin, Haidan; Zou, Zhifei; Qin, Yan; Xie, Shouxin; Chen, Yufang; Xu, Juan; Wang, Lan; Chen, Chuying

    2013-02-01

    A dispersive solid phase extraction-high performance liquid chromatographic (HPLC) method was established for the simultaneous determination of 2,4-D, thiabendazole, 2-naphthol, o-phenyl phenol, diphenyl ether and biphenyl in the fruits and vegetables. The samples were vortexed for extraction with acetonitrile containing sodium chloride and anhydrous magnesium sulfate. The acetonitrile extraction was purified by acidic alumina dispersed solid phase extraction. The analysis was performed on an Agilent TC C18 column (250 mm x 4.6 mm, 5 microm) and an ultraviolet detector at 235 nm with a mobile phase of methanol-0.02 mol/L (pH 6) potassium dihydrogen phosphate solution, at a flow rate of 1.0 mL/min with gradient elution. Good linearities were observed in the range of 0.5-20 mg/L with correlation coefficients greater than 0.99. The average recoveries of the six preservatives in fruits and vegetables were in the range of 84.2% -99. 1% at three spiked levels of 1, 2 and 10 mg/kg (n = 6) and the relative standard deviations (RSDs) were in the range of 1.67%-10.3%. The limits of quantification were 1 mg/kg. This method is simple, accurate and suitable for the determination of the six preservatives in fruits and vegetables.

  17. Investigation of Di-ethylhexyl Phthalate Migration by Applying Magnetic Solid Phase Extraction Method Followed by GC-FID Determination

    Directory of Open Access Journals (Sweden)

    Mohammad Faraji

    2016-10-01

    Full Text Available Background and Objectives: The addition of plasticizers (mainly phthalates and adipates makes plastic flexible and popular for packaging, storing and preserving food, water, and so on. The most widely used plasticizer in food contact applications is di-ethylhexyl phthalate (DEHP though being suspected to have carcinogenic and estrogenic properties. The aim of this study is application of magnetic solid phase extraction as new absorbent for determination of DEHP in water samples by gas chromatography (GC. Materials and Methods: Important factors in extraction, separation and determination processes were optimized using the one-variable-at-a-time method. For optimization, all tests were performed two times. Figures of merit of the proposed method were evaluated. The amount of DEHP in some water samples was determined using the proposed method. Results: The results showed that the obtained chromatogram of extract was free of significant interference. The preservatives’ recoveries ranged from 91.6% to 102.2%. Limit of detection and limit of quantitation were 0.1 mg kg-1 and 0.3 µg L-1, respectively. Concentration of DEHP in the studied samples was in the range of N.D-2.3 µg L-1. Conclusions: The acceptable performance and reliability of the proposed method were demonstrated. Temperature and time were fount as the most effective parameters in migration of DEHP. Keywords: Di-ethylhexyl phthalate, Magnetic solid phase extraction, Migration, Gas chromatography

  18. Magnetic graphene dispersive solid phase extraction combining high performance liquid chromatography for determination of fluoroquinolones in foods.

    Science.gov (United States)

    He, Xin; Wang, Geng Nan; Yang, Kun; Liu, Hui Zhi; Wu, Xia Jun; Wang, Jian Ping

    2017-04-15

    In this study, a magnetic graphene-based dispersive solid phase extraction method was developed that was combined with high performance liquid chromatography to determine the residues of fluoroquinolone drugs in foods of animal origin. During the experiments, several parameters possible influencing the extraction performance were optimized (amount of magnetic graphene, sample pH, extraction time and elution solution). This extraction method showed high absorption capacities (>6800ng) and high enrichment factors (68-79-fold) for seven fluoroquinolones. Furthermore, this absorbent could be reused for at least 40 times. The limits of detection were in the range of 0.05-0.3ng/g, and the recoveries from the standards fortified blank samples (bovine milk, chicken muscle and egg) were in the range of 82.4-108.5%. Therefore, this method could be used as a simple and sensitive tool to determine the residues of fluoroquinolones in foods of animal origin.

  19. Rational design and chromatographic evaluation of histamine imprinted polymers optimised for solid-phase extraction of wine samples.

    Science.gov (United States)

    Basozabal, Itsaso; Gomez-Caballero, Alberto; Diaz-Diaz, Goretti; Guerreiro, António; Gilby, Stuart; Goicolea, M Aranzazu; Barrio, Ramón J

    2013-09-20

    This article reports on the computational design, development and application of a molecularly imprinted polymer (MIP) with specific affinity towards histamine. Computational modelling was used to screen a monomer library in order to select the monomers able to form the strongest complex with the target analyte. These were subsequently used for MIP synthesis by radical polymerisation initiated by UV. MIPs were then evaluated by liquid chromatography and solid phase extraction (SPE) and best MIP behaviour was observed when itaconic acid was used as functional monomer. Finally, after optimisation of the polymer composition, MIPs were used as adsorbents for SPE and clean-up of histamine in wine samples. The proposed histamine extraction method with the MIP-SPE cartridge was found to be reproducible (wine extracts. The described methodology is simple and fast and is suitable for the selective histamine extraction and its subsequent quantification by HPLC-DAD from complex matrices such as wine samples.

  20. Serum protein profiling by miniaturized solid-phase extraction and matrix-assisted laser desorption/ionization mass spectrometry

    DEFF Research Database (Denmark)

    Callesen, Anne K; Mohammed, Shabaz; Bunkenborg, Jakob;

    2005-01-01

    for translation of MALDI-MS based diagnostic methods to clinical applications. We have investigated a number of MALDI matrices and several miniaturized solid-phase extraction (SPE) methods for serum protein concentration and desalting with the aim of generating reproducible, high-quality protein profiles by MALDI...... mass spectra (m/z 1000-12,000) to be obtained from serum. In a proof-of-principle application, SPE with chelating material and MALDI-MS identified protein peaks in serum that had been previously reported for distinguishing a person diagnosed with breast cancer from a control. These preliminary results...

  1. Solid phase extraction method for the study of black carbon cycling in dissolved organic carbon using radiocarbon

    OpenAIRE

    2015-01-01

    © 2015 Elsevier B.V.. Radiocarbon analysis is a powerful tool for understanding the cycling of individual components within carbon pools, such as black carbon (BC) in dissolved organic carbon (DOC). Radiocarbon (δ14C) measurements of BC in DOC provide insight into one source of aged, recalcitrant DOC. We report a modified solid phase extraction (SPE) method to concentrate 43±6% of DOC (SPE-DOC) from seawater. We used the Benzene Polycarboxylic Acid (BPCA) method to isolate BC from SPE-DOC (SP...

  2. Rotating disk sorbent extraction for pre-concentration of chromogenic organic compounds and direct determination by solid phase spectrophotometry.

    Science.gov (United States)

    Richter, Pablo; Cañas, Alejandro; Muñoz, Carlos; Leiva, Claudio; Ahumada, Inés

    2011-06-10

    A novel and very simple microextraction approach for pre-concentration and direct solid phase spectrophotometric measurement has been developed for the determination of chromogenic analytes. The model analyte to assess this approach was the chromophore malachite green (MG). The analyte was extracted from water samples onto a small rotating disk made of Teflon containing a sorbent phase of polydimethylsiloxane (PDMS) on one of its surfaces. We refer to the extraction procedure as rotating disk sorptive extraction (RDSE). After extraction, the sorbent phase with the concentrated analyte was separated from the Teflon disk and used directly for MG determination by solid phase spectrophotometry at 624 nm, without the necessity of a desorption step. Chemical and extraction variables such as concentration of sodium sulfate, pH, disk rotational velocity, extraction time, and temperature were studied in order to establish the best conditions for extraction. Under optimum conditions, the extraction of MG was carried out in 18 min and 90 min, for sample volumes of 100mL or 1000 mL, respectively. The detection limit, based on three times the standard deviation of the blank phase (3σ(b)), was 1.4 μg L⁻¹ and the repeatability, expressed as relative standard deviation (RSD), for 20 μg L⁻¹ MG was 8.1%. This study also applied the method to real samples, obtaining quantitative recovery (mean recovery of 99.3%). The PDMS phases could be reused after desorbing the MG into methanol for 3h. Replacement of the PDMS film onto the disk is very easy and low cost.

  3. A combination of solid-phase extraction and dispersive solid-phase extraction effectively reduces the matrix interference in liquid chromatography-ultraviolet detection during pyraclostrobin analysis in perilla leaves.

    Science.gov (United States)

    Farha, Waziha; Rahman, Md Musfiqur; Abd El-Aty, A M; Jung, Da-I; Kabir, Md Humayun; Choi, Jeong-Heui; Kim, Sung-Woo; Im, So Jeong; Lee, Young-Jun; Shin, Ho-Chul; Kwon, Chan-Hyeok; Son, Young-Wook; Lee, Kang-Bong; Shim, Jae-Han

    2015-12-01

    Perilla leaves contain many interfering substances; thus, it is difficult to protect the analytes during identification and integration. Furthermore, increasing the amount of sample to lower the detection limit worsens the situation. To overcome this problem, we established a new method using a combination of solid-phase extraction and dispersive solid-phase extraction to analyze pyraclostrobin in perilla leaves by liquid chromatography with ultraviolet absorbance detection. The target compound was quantitated by external calibration with a good determination coefficient (R(2) = 0.997). The method was validated (in triplicate) with three fortification levels, and 79.06- 89.10% of the target compound was recovered with a relative standard deviation <4. The limits of detection and quantification were 0.0033 and 0.01 mg/kg, respectively. The method was successfully applied to field samples collected from two different areas at Gwangju and Muan. The decline in the resiudue concentrations was best ascribed to a first-order kinetic model with half-lives of 5.7 and 4.6 days. The variation between the patterns was attributed to humidity.

  4. Supported liquid membrane-protected molecularly imprinted beads for micro-solid phase extraction of sulfonamides in environmental waters.

    Science.gov (United States)

    Díaz-Álvarez, M; Barahona, F; Turiel, E; Martín-Esteban, A

    2014-08-29

    In this work, molecularly imprinted polymer (MIP) beads have been prepared and evaluated for the development of a supported liquid membrane-protected micro-solid phase extraction method for the analysis of sulfonamides (SAs) in aqueous samples. The performance of MIP beads was firstly evaluated in cartridges by conventional solid-phase extraction for the simultaneous analysis of SAs. Afterward, beads were packed into a polypropylene hollow fiber protected by an organic solvent immobilized in the pores of the capillary wall. During the process, the analytes were extracted from the aqueous sample to the immobilized organic solvent and then selectively retained by the MIP beads located inside the capillary. The effect of various experimental parameters as sample pH, time and stirring-rate among others, were studied for the establishment of optimum rebinding conditions. Relative recoveries for all sulfonamides tested in river and reservoir water samples by the proposed method using 100mL water sample spiked with 50μg L-1 of each sulfonamide were within 70-120%, with a relative standard deviation (RSD) <10% (n=3). The detection limits (LODs) were within 0.2-3μgL(-1), depending upon the sulfonamide and the type of water used.

  5. Determination of Phthalate Plasticisers in Palm Oil Using Online Solid Phase Extraction-Liquid Chromatography (SPE-LC

    Directory of Open Access Journals (Sweden)

    Nazarudin Ibrahim

    2014-01-01

    Full Text Available Contamination of phthalates plasticisers to food has raised concern as some of the phthalates are suspected to be endocrine disruptors. The phthalates have high affinity with oily environment and analysing these chemicals in such matrices is difficult because of the trace amount of the analyte and interference from matrix. An online solid phase extraction (SPE technique using a large volume (3.5 mL injection was developed for the analysis of 6 common plasticisers in palm oil. A simple sample preparation involving alumina as a fat retainer and methanol : acetonitrile (1 : 1 as the extraction solvent was performed prior to the usage of online SPE-LC system. This system consists of two columns, C16 for the solid phase extraction (SPE and C18 as the analytical column, and a photo diode array detector. The calibration curves were linear from 5 to 1000 μg L−1, with correlation coefficients above 0.99. The instrumental limit of detection was 3 μg L−1 and satisfactory recovery was obtained. A screening on a few samples in the retail market revealed the presence of dibutyl phthalate (DBP and butylbenzylphthalate (BBP in the palm oil, with concentration less than 1 mg L−1.

  6. Determination of chlorinated polycyclic aromatic hydrocarbons in water by solid-phase extraction coupled with gas chromatography and mass spectrometry.

    Science.gov (United States)

    Wang, Xianli; Kang, Haiyan; Wu, Junfeng

    2016-05-01

    Given the potential risks of chlorinated polycyclic aromatic hydrocarbons, the analysis of their presence in water is very urgent. We have developed a novel procedure for determining chlorinated polycyclic aromatic hydrocarbons in water based on solid-phase extraction coupled with gas chromatography and mass spectrometry. The extraction parameters of solid-phase extraction were optimized in detail. Under the optimal conditions, the proposed method showed wide linear ranges (1.0-1000 ng/L) with correlation coefficients ranging from 0.9952 to 0.9998. The limits of detection and the limits of quantification were in the range of 0.015-0.591 and 0.045-1.502 ng/L, respectively. Recoveries ranged from 82.5 to 102.6% with relative standard deviations below 9.2%. The obtained method was applied successfully to the determination of chlorinated polycyclic aromatic hydrocarbons in real water samples. Most of the chlorinated polycyclic aromatic hydrocarbons were detected and 1-monochloropyrene was predominant in the studied water samples. This is the first report of chlorinated polycyclic aromatic hydrocarbons in water samples in China. The toxic equivalency quotients of chlorinated polycyclic aromatic hydrocarbons in the studied tap water were 9.95 ng the toxic equivalency quotient m(-3) . 9,10-Dichloroanthracene and 1-monochloropyrene accounted for the majority of the total toxic equivalency quotients of chlorinated polycyclic aromatic hydrocarbons in tap water.

  7. A sensitive and selective molecularly imprinted sensor combined with magnetic molecularly imprinted solid phase extraction for determination of dibutyl phthalate.

    Science.gov (United States)

    Zhang, Zhaohui; Luo, Lijuan; Cai, Rong; Chen, Hongjun

    2013-11-15

    A highly sensitive and selective molecularly imprinted (MIP) sensor combined with magnetic molecularly imprinted solid phase extraction (MMISPE) was developed for the determination of dibutyl phthalate (DBP) in complex matrixes. The magnetic molecularly imprinted polymer (MMIP) was synthesized as solid phase extraction (SPE) sorbet to extract DBP from complex matrixes and as sensing element to improve the selectivity of the imprinted sensor. The morphologies of MMIP and MIP-sensor were characterized by using scanning electron microscope (SEM) and transmission electron microscopy (TEM). The electrochemical performances of MIP-sensor were investigated by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The conditions of preconcentration, elution and electrochemical determination were studied in detail. Under the optimized experimental conditions, the response currents of the MIP-sensor exhibited a linear relationship towards DBP concentrations ranging from 1.0 × 10(-8)g/L to 1.0 × 10(-3)g/L. The limit of detection of the MMIP-sensor coupled with the MMISPE was calculated as 0.052 ng/L. The MMIP-sensor coupled with the MMISPE was applied to detect DBP in complex samples successfully.

  8. Solid-phase extraction of esculetin from the ash bark of Chinese traditional medicine by using molecularly imprinted polymers.

    Science.gov (United States)

    Hu, Shu-Guo; Li, Li; He, Xi-Wen

    2005-01-07

    A molecularly imprinted polymer solid-phase extraction method is used to extract esculetin from the ash bark of Chinese traditional medicine. Ratio of ethanol and water as washing solution were investigated. Data of accumulative adsorption on molecularly imprinted polymers from the continuous loading experiment suggests that there are two different kinds of recognition sites in molecularly imprinted polymers. By selecting the washing and eluting solution a scheme was designed to separate esculetin and its analogues including esculin, coumarin, 7-methoxylcoumarin and daphnetin. Finally, by applying the revised scheme esculetin was extracted from the ash bark of Chinese traditional medicine that was purchased from two big drugstores, respectively, with both molecularly imprinted polymers and non-molecularly imprinted polymers.

  9. Magnetic field assisted μ-solid phase extraction of anti-inflammatory and loop diuretic drugs by modified polybutylene terephthalate nanofibers

    Energy Technology Data Exchange (ETDEWEB)

    Bagheri, Habib, E-mail: bagheri@sharif.edu; Khanipour, Peyman; Asgari, Sara

    2016-08-31

    A magnetic nanocomposite consisting of nanoparticles–polybutylene terephthalate (MNPs–PBT) was electrospun and used as an extracting medium for an on-line μ-solid phase extraction (μ–SPE)–high performance liquid chromatography (HPLC) set–up with an ultraviolet (UV) detection system. Due to the magnetic property of the prepared nanofibers, the whole extraction procedure was implemented under an external magnetic field to enhance the extraction efficiencies. The developed method along with the synthesized nanocomposite were found to be appropriate for the determination of trace levels of selected drugs including furosemide, naproxen, diclofenac and clobetasol propionate in the urine sample. The prepared MNPs-PBT electrospun nanocomposite was characterized using the scanning electron microscopy (SEM), energy dispersive spectroscopy (EDX) and Fourier transform infrared (FT–IR) spectroscopy. The prepared magnetic fibers showed high porosity, which was another driving force for the extraction efficiency enhancement. Major parameters affecting the extraction efficiency of the selected drugs were optimized. The limits of detections (LOD) of the studied drugs were in the range of 0.4–1.6 μg L{sup −1} and the limits of quantification (LOQ) were 1–4 μg L{sup −1} under the optimized conditions. Relative standard deviation (RSD%) for three replicates at three concentration levels of 6, 100 and 400 μg L{sup −1} were 5.9–8.0% while acceptable linear range with two orders of magnitude was obtained (R{sup 2} = 0.99). The method was validated by the determination of the selected drugs in urine samples and the results indicated that this method has sufficient potential for enrichment and determination of the desired drugs in the urine sample. The relative recovery values were found to be in the range of 78–91%. Implementing the developed on–line μ–SPE method under the external magnetic field induction, led to higher extraction efficiencies

  10. Solid-phase microextraction

    DEFF Research Database (Denmark)

    Nilsson, Torben

    The objective of this study has been to develop new analytical methods using the rapid, simple and solvent-free extraction technique solid-phase microextraction (SPME) for the quantitative analysis of organic pollutants at trace level in drinking water and environmental samples. The dynamics...

  11. Comparison of the solid-phase extraction efficiency of a bounded and an included cyclodextrin-silica microporous composite for polycyclic aromatic hydrocarbons determination in water samples.

    Science.gov (United States)

    Mauri-Aucejo, Adela; Amorós, Pedro; Moragues, Alaina; Guillem, Carmen; Belenguer-Sapiña, Carolina

    2016-08-15

    Solid-phase extraction is one of the most important techniques for sample purification and concentration. A wide variety of solid phases have been used for sample preparation over time. In this work, the efficiency of a new kind of solid-phase extraction adsorbent, which is a microporous material made from modified cyclodextrin bounded to a silica network, is evaluated through an analytical method which combines solid-phase extraction with high-performance liquid chromatography to determine polycyclic aromatic hydrocarbons in water samples. Several parameters that affected the analytes recovery, such as the amount of solid phase, the nature and volume of the eluent or the sample volume and concentration influence have been evaluated. The experimental results indicate that the material possesses adsorption ability to the tested polycyclic aromatic hydrocarbons. Under the optimum conditions, the quantification limits of the method were in the range of 0.09-2.4μgL(-1) and fine linear correlations between peak height and concentration were found around 1.3-70μgL(-1). The method has good repeatability and reproducibility, with coefficients of variation under 8%. Due to the concentration results, this material may represent an alternative for trace analysis of polycyclic aromatic hydrocarbons in water trough solid-phase extraction.

  12. [Determination of trace silver in water samples by solid phase extraction portable tungsten-coil electrothermal atomic absorption spectrometry].

    Science.gov (United States)

    Fan, Guang-yu; Jiang, Xiao-ming; Zheng, Cheng-bin; Hou, Xian-deng; Xu, Kai-lai

    2011-07-01

    A simple method has been developed for the determination of silver in environmental water samples using solid phase extraction with tungsten-coil electrothermal atomic absorption spectrometry. Silica gel was used as an adsorbent and packed into a syringe barrel for solid phase extraction of silver prior to its determination by using a portable tungsten-coil electrothermal atomic absorption spectrometer. Optimum conditions for adsorption and desorption of silver ion, as well as interferences from co-existing ions, were investigated. A sample pH value of 6.0, a sample loading flow rate of 4.0 mL x min(-1), and the mixture of 4% (m/v) thiourea and 2% (phi) nitrate acid with the eluent flow rate of 0.5 mL x min(-1) for desorption were selected for further studies. Under optimal conditions, a linear range of 0.20-4.00 ng x mL(-1), a limit of detection (3sigma) of 0.03 ng x mL(-1) and a preconcentration factor of 94 were achieved. The proposed method was validated by testing three environmental water samples with satisfactory results.

  13. [Determination of nonylphenol in wastewater by solid phase extraction gas chromatography mass spectrometry and multi-selective ions].

    Science.gov (United States)

    Hao, Rui-Xia; Liang, Peng; Zhao, Man; Wang, Jun-An; Zhou, Yu-Wen

    2006-11-01

    Nonylphenol (NP) having endocrine disrupter activity is an ultra trace component in sewage and reuse wastewater. There are many NP isomers in the wastewater because nonyl structure is different. The background impurity of the samples is very complex with many other components. So it is difficulty for quantitative analysis of NP in the samples. About seventy sewages and recycled wastewater samples were measured for the content of NP isomer mixtures by solid-phase extraction-gas chromatography-mass spectrometry and multi-selected ions monitoring (shortened as SPE-GC-MS-SIM). The results show that hydrophilic-lipophilic-equilibrium solid-phase extraction pole has selective adsorption for NP, so that the samples can be concentrated from 50 to 200 times. The five kinds of mass spectrum ions, i. e. 107, 121, 135, 149, 163, have higher abundance and distinct character. The sum of five selected ion monitoring (sigmaSIM) is from 54.4 to 73 percent of the total ion current for NP, which can accurately represent different NP isomers. Quantitative analysis base on the spectral integralof the sigmaSIM chromatograph can eliminate interference with background signal and ensure selectivity, accuracy and precision ofthe method.

  14. [Determination of short chain chlorinated paraffins in leather products by solid phase extraction coupled with gas chromatography-mass spectrometry].

    Science.gov (United States)

    Zhang, Weiya; Wan, Xin; Li, Lixia; Wang, Chengyun; Jin, Shupei; Xing, Jun

    2014-10-01

    The short chain chlorinated paraffins (SCCPs) are the additives frequently used in the leather production in China, but they have been put into the list of forbidden chemicals issued by European Union recently. In fact, there is not a commonly recognized method for the determination of the SCCPs in the leather products due to the serious matrix interferences from the leather products and the complex chemical structures of the SCCPs. A method of solid phase extraction coupled with gas chromatography-mass spectrometry (SPE-GC-MS) was established for the determination of the SCCPs in the leather products after the optimization of the SPE conditions. It was found that the interferences from the leather products were thor- oughly separated from the analyte of the SCCPs on a home-made solid phase extraction (SPE) column filled with silica packing while eluted with a mixed solvent of n-hexane-methylene chloride (2:1, v/v). With this method, the recoveries for the SCCPs spiked in the real leather samples varied from 90.47% to 99.00% with the relative standard deviations (RSDs) less than 6.7%, and the limits of detection (LODs) were between 0.069 and 0.110 mg/kg. This method is suitable for qualitative and quantitative analysis of SCCPs in the leather products.

  15. Chromium speciation by solid phase extraction on Dowex M 4195 chelating resin and determination by atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Saygi, Kadriye Ozlem; Tuzen, Mustafa [Gaziosmanpasa University, Faculty of Science and Arts, Chemistry Department, 60250 Tokat (Turkey); Soylak, Mustafa [Erciyes University, Faculty of Science and Arts, Chemistry Department, 38039 Kayseri (Turkey)], E-mail: msoylak@gmail.com; Elci, Latif [Pamukkale University, Faculty of Science and Arts, Chemistry Department, 20020 Denizli (Turkey)

    2008-05-30

    A solid phase extraction procedure has been established for chromium speciation in natural water samples prior to determination by atomic absorption spectrometry. The procedure is based on the solid phase extraction of the Cr(VI)- Dowex M 4195 chelating resin. After oxidation of Cr(III) to Cr(VI) by using H{sub 2}O{sub 2}, the presented method was applied to the determination of the total chromium. The level of Cr(III) is calculated by difference of total chromium and Cr(VI) levels. The procedure was optimized for some analytical parameters including pH, eluent type, flow rates of sample and eluent, matrix effects, etc. The presented method was applied for the speciation of chromium in natural water samples with satisfactory results (recoveries >95%, RSDs <10%). In the determinations of chromium species, flame atomic absorption spectrometer was used. The results were checked by using NIST SRM 2711 Montana soil and GBW 07603 Bush branched and leaves.

  16. DETERMINATION OF FLUORIDE IN HIGHLY SALINATED WATERS BY ION CHROMATOGRAPHY METHOD WITH USE OF SOLID PHASE EXTRACTION FOR SAMPLE PREPARATION

    Directory of Open Access Journals (Sweden)

    Beata Kostka

    2014-10-01

    Full Text Available Solid phase extraction (SPE is one of the most popular methods of matrix elimination in determination of anions by ion chromatography. Possibility of using cartridges containing a cation-exchange resin in the Ag+ and Na+ forms for determination of fluoride in the presence of very high concentration of chloride in mine waters was described in this paper. A Dionex ICS-2500 ion chromatograph was used for separation of anions in gradient elution using IonPac AS19 (4x250 mm separation column along with generated KOH eluent. Fluoride after separation was determined by conductivity detector with suppression. The investigations performed on mine waters (conductivity in the range 12 700 μS/cm–155 000 μS/cm and synthetic brine (38 820 mg/L Cl- and 3 408 mg/L SO4 2- confirmed usefulness of cartridges containing a cation-exchange resin for minimizing matrix influence on results of fluoride determination. The ion chromatography method accompanied by solid phase extraction for sample preparation proved to be very useful for determination of fluoride in highly salinated waters (i.e. mine waters because of low detection limit (0,02 mg/L, good precision (< 2,5 % and accuracy (recovery 91 % – 104 %.

  17. Sodium dodecyl sulfate coated poly (vinyl) chloride: an alternative support for solid phase extraction of some transition and heavy metals.

    Science.gov (United States)

    Marahel, Farzaneh; Ghaedi, Mehrorang; Shokrollahi, Ardeshir; Montazerozohori, Morteza; Davoodi, Shahnaz

    2009-01-01

    A simple and relatively fast approach for developing a solid phase extraction has been described and used for determination of trace quantities of some heavy and transition metal ions with sodium dodecyl sulfate (SDS)-coated poly vinyl chloride (PVC) modified with bis(2-hydroxyacetophenone)-1,4-butanediimine (BHABDI) ligand. The adsorbed ions were stripped from the solid phase by 10 mL of 3M nitric acid as eluent. The eluting solution was analyzed for metals content (cadmium, chromium, cobalt, copper, lead and zinc) by flame atomic absorption spectrometry (FAAS). The main factors such as pH, amount of ligand and PVC, amount and type of surfactant, and condition of eluting solutions on the sorption recovery of metal ions have been investigated in detail. The relative standard deviation was found in the range of 1.0-3.2% for 0.2 microg mL(-1)of metals ions. After optimization of the extraction condition and the instrumental parameters, a detection limit was found to be in the range of 1.2-3.1 microg L(-1), with enrichment factor of 50 was achieved. The method was successfully applied for the determination of these metals contents in real samples with satisfactory results.

  18. Advanced analytical method of nereistoxin using mixed-mode cationic exchange solid-phase extraction and GC/MS.

    Science.gov (United States)

    Park, Yujin; Choe, Sanggil; Lee, Heesang; Jo, Jiyeong; Park, Yonghoon; Kim, Eunmi; Pyo, Jaesung; Jung, Jee H

    2015-07-01

    Nereistoxin(NTX) was originated from a marine annelid worm Lumbriconereis heteropoda and its analogue pesticides including cartap, bensultap, thiocyclam and thiobensultap have been commonly used in agriculture, because of their low toxicity and high insecticidal activity. However, NTX has been reported about its inhibitory neuro toxicity in human and animal body, by blocking nicotinic acetylcholine receptor and it cause significant neuromuscular toxicity, resulting in respiratory failure. We developed a new method to determine NTX in biological fluid. The method involves mixed-mode cationic exchange based solid phase extraction and gas chromatography/mass spectrometry for final identification and quantitative analysis. The limit of detection and recovery were substantially better than those of other methods using liquid-liquid extraction or headspace solid phase microextraction. The good recoveries (97±14%) in blood samples were obtained and calibration curves over the range 0.05-20 mg/L have R2 values greater than 0.99. The developed method was applied to a fatal case of cartap intoxication of 74 years old woman who ingested cartap hydrochloride for suicide. Cartap and NTX were detected from postmortem specimens and the cause of the death was ruled to be nereistoxin intoxication. The concentrations of NTX were 2.58 mg/L, 3.36 mg/L and 1479.7 mg/L in heart, femoral blood and stomach liquid content, respectively. The heart blood/femoral blood ratio of NTX was 0.76.

  19. New cold-fiber headspace solid-phase microextraction device for quantitative extraction of polycyclic aromatic hydrocarbons in sediment.

    Science.gov (United States)

    Ghiasvand, Ali Reza; Hosseinzadeh, Shokouh; Pawliszyn, Janusz

    2006-08-18

    A new automated headspace solid-phase microextraction (HS-SPME) sampling device was developed, with the capability of heating the sample matrix and simultaneously cooling the fiber coating. The device was evaluated for the quantitative extraction of polycyclic aromatic hydrocarbons (PAHs) from solid matrices. The proposed device improves the efficiency of the release of analytes from the matrix, facilitates the mass transfer into the headspace and significantly increases the partition coefficients of the analytes, by creating a temperature gap between the cold-fiber (CF) coating and the hot headspace. The reliability and applicability of previously reported cold-fiber devices are significantly enhanced by this improvement. In addition, it can be easily adopted for full automation of extraction, enrichment and introduction of different samples using commercially available autosampling devices. Sand samples spiked with PAHs were used as solid matrices and the effect of different experimental parameters were studied, including the extraction temperature, extraction time, moisture content, and the effect of sonication and modifier under optimal experimental conditions, linear calibration curves were obtained in the range of 0.0009-1000 ng/g, with regression coefficients higher than 0.99 and detection limits that ranged from 0.3 to 3 pg/g. Reproducible, precise and high throughput extraction, monitoring and quantification of PAHs were achieved with the automated cold-fiber headspace solid-phase microextraction (CF-HS-SPME) device coupled to GC-flame ionization detection. Determination of PAHs in certified reference sediments using the proposed approach exhibited acceptable agreement with the standard values.

  20. Solid-phase/supercritical-fluid extraction for liquid chromatography of phenolic compounds in freshwater microalgae and selected cyanobacterial species.

    Science.gov (United States)

    Klejdus, B; Kopecký, J; Benesová, L; Vacek, J

    2009-01-30

    In the present paper a new extraction technique based on the combination of solid-phase/supercritical-fluid extraction (SPE/SFE) with subsequent reversed-phase HPLC is described. The SPE/SFE extractor was originally constructed from SPE-cartridge incorporated into the SFE extraction cell. Selected groups of benzoic acid derivatives (p-hydroxybenzoic, protocatechuic, gallic, vanillic and syringic acid), hydroxybenzaldehydes (4-hydroxybenzaldehyde and 3,4-dihydroxybenzaldehyde) and cinnamic acid derivatives (o-coumaric, p-coumaric, caffeic, ferulic, sinapic and chlorogenic acid) were extracted. Cyclic addition of binary extraction solvent system based on methanol:water (1:1, v/v) and methanol/ammonia aqueous solution was used for extraction at 40MPa and 80 degrees C. The p-hydroxybenzoic, protocatechuic, vanillic, syringic, caffeic and chlorogenic acid; 4-hydroxybenzaldehyde and 3,4-dihydroxybenzaldehyde were identified by HPLC-electrospray mass spectrometry in SPE/SFE extracts of acid hydrolyzates of microalga (Spongiochloris spongiosa) and cyanobacterial strains (Spirulina platensis, Anabaena doliolum, Nostoc sp., and Cylindrospermum sp.). For the identification and quantification of the compounds the quasi-molecular ions [M-H](-) and specific fragments were analysed by quadrupole mass spectrometry analyzer. Our analysis showed that the microalgae and cyanobacteria usually contained phenolic acids or aldehydes at microg levels per gram of lyophilized sample. The proposed SPE/SFE extraction method would be useful for the analysis of different plant species containing trace amount of polar fraction of phenols.

  1. Preparation of 4-butylaniline-bonded silica gel for the solid-phase extraction of flavone glycosides.

    Science.gov (United States)

    Chu, Ganghui; Cai, Wensheng; Shao, Xueguang

    2015-04-01

    To extract flavone glycosides efficiently, a new extraction material based on 4-butylaniline-bonded silica gel was prepared using a two-step grafting method including a ring-opening reaction and synchronous hydrolysis. Preparation of the silica-based material was easily achieved under mild conditions, and the material was characterized by Fourier transform infrared spectroscopy, elemental analysis, and scanning electron microscopy. The material was used in solid-phase extraction, and the extraction can be performed in neutral conditions without regard to ionic strength. Selectivity tests of 14 compounds on the extraction cartridge showed that the material has a high affinity to flavone glycosides in contrast to octadecyl silica, and the extraction yields for four flavone glycosides were found to be >93%. Selectivity tests further reveal that the adsorption on its surface is likely attributed to multiple interactions, including hydrophobic interactions, π-π interactions, and hydrogen bonding. To explore the applicability of 4-butylaniline-bonded silica gel, naringin and hesperidin from Simotang oral liquid were extracted, and the extraction yields were >90%, which is distinguished from silica cartridge.

  2. Solid-phase extraction-thermal desorption-gas chromatography with mass selective detection for the determination of drugs in urine

    NARCIS (Netherlands)

    van Hout, MWJ; de Zeeuw, RA; Franke, JP; de Jong, GJ

    2003-01-01

    Solid-phase extraction (SPE) was combined with thermal desorption (TD) and gas chromatographic (GC) analysis to determine drugs in urine. The extraction was performed inside a fritted GC liner using about 5 mg TENAX that was inserted into the liner on top of the frit. After extraction, the liner was

  3. Solid-phase extraction based on ground methacrylate monolith modified with gold nanoparticles for isolation of proteins.

    Science.gov (United States)

    Vergara-Barberán, María; Lerma-García, María Jesús; Simó-Alfonso, Ernesto Francisco; Herrero-Martínez, José Manuel

    2016-04-21

    In this study, a novel polymeric material functionalized with gold nanoparticles (AuNPs) was prepared as solid-phase extraction (SPE) sorbent for isolation of proteins. The sorbent was synthesized from a powdered poly(glycidyl-co-ethylene dimethacrylate) monolith, and modified with ammonia, followed by immobilization of AuNPs on the pore surface of the material. To evaluate the performance of this SPE support, proteins were selected as test solutes, being the extraction conditions and other parameters (loading capacity and regenerative ability of sorbent) established. The results indicated that this sorbent could be employed to selectively capture proteins according to their pI, on the basis of the strong affinity of these biomacromolecules towards to AuNPs surface. The applicability of this sorbent was demonstrated by isolating protein species of interest (bovine serum albumin, cytochrome c and lectins in European mistletoe leaves), followed by SDS-PAGE analysis.

  4. Fluorometric determination of nonylphenol in water samples enriched with zirconium doped titanium dioxide nanotubes solid phase extraction

    Institute of Scientific and Technical Information of China (English)

    Xian Fa Su; Xin Ning Zhao; Guo Hong Xie; Qing Xiang Zhou

    2012-01-01

    This paper developed a fluorometric method for the sensitive determination of nonylphenol in water samples by preconcentration with zirconium doped titanium dioxide nanotubes solid phase extraction.The parameters on extraction that would influence the enrichment performance such as the kind and volume of eluent,sample pH,sample flow rate,and sample volume were optimized in detail.Under the optimal conditions,the proposed method provided an excellent linear range of 1-150 μg/L and good LOD of 0.076 μg/L.The relative standard deviation (RSD,n =6) was 2.8%.Proposed method was also used for the analysis of real water samples and the spiked recoveries were satisfied in the range of 98.7-103%.

  5. Extraction of Genomic DNA Using Magnetic Nanoparticles (Fe3O4 as a Solid-Phase Support

    Directory of Open Access Journals (Sweden)

    Z. M. Saiyed

    2007-01-01

    Full Text Available Magnetic separation technology, using magnetic particles, is quick and easy method for sensitive and reliable captures of specific proteins, genetic material and other biomolecules. The current paper describes a universal genomic DNA extraction method optimized in our laboratory using magnetic nanoparticles as a solid phase adsorbent. The yields of the isolated DNA with magnetic method were higher or equivalent to the conventional procedures in all the samples tested. Additionally, the magnetic method takes less than 15 minutes to extract DNA as against several hours taken by conventional protocols. Furthermore, the isolated DNA was found to function satisfactorily in PCR amplification and restriction endonuclease digestion. The developed procedure is simple, quick, cheap, robust and does not require the use of organic solvents or sophisticated equipments; thereby making it more amenable to automation.

  6. Screening for Anabolic Steroids in Urine of Forensic Cases Using Fully Automated Solid Phase Extraction and LC–MS-MS

    DEFF Research Database (Denmark)

    Andersen, David Wederkinck; Linnet, Kristian

    2014-01-01

    A screening method for 18 frequently measured exogenous anabolic steroids and the testosterone/epitestosterone (T/E) ratio in forensic cases has been developed and validated. The method involves a fully automated sample preparation including enzyme treatment, addition of internal standards...... and solid phase extraction followed by analysis by liquid chromatography-tandem mass spectrometry (LC-MS-MS) using electrospray ionization with adduct formation for two compounds. Urine samples from 580 forensic cases were analyzed to determine the T/E ratio and occurrence of exogenous anabolic steroids....... Extraction recoveries ranged from 77 to 95%, matrix effects from 48 to 78%, overall process efficiencies from 40 to 54% and the lower limit of identification ranged from 2 to 40 ng/mL. In the 580 urine samples analyzed from routine forensic cases, 17 (2.9%) were found positive for one or more anabolic...

  7. Matrix molecularly imprinted mesoporous sol-gel sorbent for efficient solid-phase extraction of chloramphenicol from milk.

    Science.gov (United States)

    Samanidou, Victoria; Kehagia, Maria; Kabir, Abuzar; Furton, Kenneth G

    2016-03-31

    Highly selective and efficient chloramphenicol imprinted sol-gel silica based inorganic polymeric sorbent (sol-gel MIP) was synthesized via matrix imprinting approach for the extraction of chloramphenicol in milk. Chloramphenicol was used as the template molecule, 3-aminopropyltriethoxysilane (3-APTES) and triethoxyphenylsilane (TEPS) as the functional precursors, tetramethyl orthosilicate (TMOS) as the cross-linker, isopropanol as the solvent/porogen, and HCl as the sol-gel catalyst. Non-imprinted sol-gel polymer (sol-gel NIP) was synthesized under identical conditions in absence of template molecules for comparison purpose. Both synthesized materials were characterized by Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FT-IR) and nitrogen adsorption porosimetry, which unambiguously confirmed their significant structural and morphological differences. The synthesized MIP and NIP materials were evaluated as sorbents for molecularly imprinted solid phase extraction (MISPE) of chloramphenicol in milk. The effect of critical extraction parameters (flow rate, elution solvent, sample and eluent volume, selectivity coefficient, retention capacity) was studied in terms of retention and desorption of chloramphenicol. Competition and cross reactivity tests have proved that sol-gel MIP sorbent possesses significantly higher specific retention and enrichment capacity for chloramphenicol compared to its non-imprinted analogue. The maximum imprinting factor (IF) was found as 9.7, whereas the highest adsorption capacity of chloramphenicol by sol-gel MIP was 23 mg/g. The sol-gel MIP was found to be adequately selective towards chloramphenicol to provide the necessary minimum required performance limit (MRPL) of 0.3 μg/kg set forth by European Commission after analysis by LC-MS even without requiring time consuming solvent evaporation and sample reconstitution step, often considered as an integral part in solid phase extraction work-flow. Intra and

  8. Magnetic nano graphene oxide as solid phase extraction adsorbent coupled with liquid chromatography to determine pseudoephedrine in urine samples.

    Science.gov (United States)

    Taghvimi, Arezou; Hamishehkar, Hamed; Ebrahimi, Mahmoud

    2016-01-15

    This paper reports on a method based on magnetic solid phase extraction (MSPE) for the determination of pseudoephedrine. Magnetic nanographene oxide (MNGO) was applied as a new adsorbent for the extraction of pseudoephedrine from urine samples. Synthesis of MNGO was characterized by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), powder X-ray diffraction (XRD), and vibrating sample magnetometer (VSM). The main factors influencing extraction efficiency, including the amounts of sample volume, amount of adsorbent, type and amount of extraction organic solvent, time of extraction and desorption, pH, ionic strength of extraction medium, and agitation rate, were investigated and optimized. Under optimized extraction conditions, a good linearity was observed in the range of 100-2000ng/mL with a correlation coefficient of 0.9908 (r(2)). Limit of detection (LOD) and limit of quantification (LOQ) were 25 and 82.7ng/mL, respectively. Inter-day and intra-day precision and accuracy were 6.01 and 0.34 (%), and 8.70 and 0.29 (%), respectively. The method was applied for the determination of pseudoephedrine in urine samples of volunteers receiving pseudoephedrine with the recovery of 96.42. It was concluded that the proposed method can be applied in diagnostic clinics.

  9. Isolation and quantitation of amygdalin in Apricot-kernel and Prunus Tomentosa Thunb. by HPLC with solid-phase extraction.

    Science.gov (United States)

    Lv, Wei-Feng; Ding, Ming-Yu; Zheng, Rui

    2005-08-01

    Apricot-kernel and Prunus Tomentosa Thunb. are traditional Chinese herb medicines that contain amygdalin as their major effective ingredient. In this report, three methods for the extraction of amygdalin from the medicinal materials are compared: ultrasonic extraction by methanol, Soxhlet extraction by methanol, and reflux extraction by water. The results show that reflux extraction water containing 0.1% citric acid is the best option. The optimal reflux is 2.5 h and water bath temperature is 60 degrees C. The solid-phase extraction method using C18 and multiwalled carbon nanotube as adsorbents is established the pretreatment of reflux extract, and the result shows that the two adsorbents have greater adsorptive capacity for amygdalin and good separation effect. In order to quantitate amygdalin in Apricot-kernel and Prunus Tomentosa Thunb., a reversed-phase high-performance liquid chromatography method using methanol-water (15:85, for 30 min and pure methanol after 30 min) as mobile phase is developed and a good result is obtained.

  10. Preconcentration and separation of nickel, copper and cobalt using solid phase extraction and their determination in some real samples.

    Science.gov (United States)

    Ghaedi, M; Ahmadi, F; Soylak, M

    2007-08-17

    A solid phase extraction method has been developed to separate and concentrate trace amounts of nickel, cobalt and copper ions from aqueous samples for the measurement by flame atomic absorption spectrometry. By the passage of aqueous samples through activated carbon modified by dithioxamide (rubeanic acid) (DTO), Ni2+, Cu2+ and Co2+ ions adsorb quantitatively. The recoveries of analytes at pH 5.5 with 500 mg solid phase were greater than 95% without interference from alkaline, earth alkaline and some metal ions. The enrichment factor was 330. The detection limits by three sigma were 0.50 microg L(-1) for copper, 0.75 microg L(-1) for nickel and 0.80 microg L(-1) for cobalt. The loading capacity was 0.56 mg g(-1) for Ni2+, 0.50 mg g(-1) for Cu2+ and 0.47 mg g(-1) for Co2+. The presented procedure was applied to the determination of analytes in tap, river and sea waters, vegetable, soil and blood samples with successfully results (recoveries greater than 95%, R.S.D. lower than 2% for n=3).

  11. Synthesis of surface molecularly imprinted polymer and the selective solid phase extraction of imidazole from its structural analogs.

    Science.gov (United States)

    Zhu, Guifen; Fan, Jing; Gao, Yanbu; Gao, Xia; Wang, Jianji

    2011-05-30

    A surface molecularly imprinted polymer (MIP) was synthesized by using imidazole as the template and modified silica particles as the support material. The static adsorption, solid phase extraction (SPE) and high-performance liquid chromatography (HPLC) experiments were performed to investigate the adsorption properties and selective recognition characteristics of the polymer for imidazole and its structural analogs. It was shown that the maximum binding capacities of imidazole on the MIP and the non-imprinted polymer (NIP) were 312 and 169 μmol g(-1), respectively. The adsorption was fast and the adsorption equilibrium was achieved in 30 min. The binding process could be described by pseudo-second order kinetics. Compared with the corresponding non-imprinted polymer, the molecularly imprinted polymer exhibited much higher adsorption performance and selectivity for imidazole. The selective separation of imidazole from a mixture of 1-hexyl-3-methylimidazolium bromide ([C(6)mim][Br]) and 2,4-dichlorophenol could be achieved on the MIP-SPE column. The recoveries of imidazole and [C(6)mim][Br] were 97.6-102.7% and 12.2-17.3%, respectively, but 2,4-dichlorophenol could not be retained on the column. The surface molecularly imprinted polymer presented here may find useful application as a solid phase absorbent to separate trace imidazole in environmental water samples. This may also form the basis for our research program on the preparation and application of alkyl-imidazolium imprinted polymers.

  12. Selective solid-phase extraction of artificial chemicals from milk samples using multiple-template surface molecularly imprinted polymers.

    Science.gov (United States)

    Zhang, Jing; Ni, Yan-li; Wang, Ling-ling; Ma, Jin-qin; Zhang, Zhi-qi

    2015-08-01

    A novel multiple-template surface molecularly imprinted polymer (MTMIP) was synthesized using ofloxacin and 17β-estradiol as templates and modified monodispersed poly(glycidylmethacrylate-co-ethylene dimethacrylate) (PGMA/EDMA ) beads as the support material. Static adsorption, solid-phase extraction and high-performance liquid chromatography were performed to investigate the adsorption properties and selective recognition characteristics of the polymer templates and their structural analogs. The maximum binding capacities of ofloxacin and 17β-estradiol on the MTMIP were 9.0 and 6.6 mg/g, respectively. Compared with the corresponding nonimprinted polymer, the MTMIP exhibited a much higher adsorption performance and selectivity toward three quinolones and three estrogens, which are common drug residues in food. The MTMIP served as a simple and effective pretreatment method and could be successfully applied to the simultaneous analysis of multiple target components in complex samples. Furthermore, the MTMIP may find useful applications as a solid-phase absorbent in the simultaneous determination of trace quinolones and estrogens in milk samples, as the recoveries were in the range 77.6-98.0%.

  13. Multidimensional gas chromatography-mass spectrometry determination of 3-alkyl-2-methoxypyrazines in wine and must. A comparison of solid-phase extraction and headspace solid-phase extraction methods.

    Science.gov (United States)

    Culleré, Laura; Escudero, Ana; Campo, Eva; Cacho, Juan; Ferreira, Vicente

    2009-05-01

    Two different strategies for the quantitative determination of 3-alkyl-2-methoxypyrazines in wine and must have been developed and validated. Comparison between both the techniques has been presented and the most adequate has been applied to the determination of these compounds in different samples of wine, made from several varieties of grapes, and also in different samples of must made from Cabernet Sauvignon grapes. Both the methods consisted of a dynamic headspace coupled with a solid-phase extraction (HS-SPE) and solid-phase extraction (SPE) directly from the sample, coupled with multidimensional gas chromatography-mass spectrometry system (MDGC-MS). Both of them require resins LiChrolut EN, and analyte elution has been carried out with dichloromethane. The repeatability of both methodologies was evaluated at two concentration levels. The relative standard deviations (RSD%) were acceptable in every case, but smaller when working with HS-SPE. The recoveries obtained for the three analytes with the two methodologies were almost 100%, with the exception of IBMP, which had a recovery of only 70% with HS-SPE. The linearity was satisfactory with both methods for the range of occurrence of methoxypyrazines in wine and must. The limits of detection of the direct SPE technique were much lower than those of HS-SPE in every case. Direct SPE method detection limits ranged from 0.09 to 0.15 ng L(-1). The method based on direct SPE was chosen finally because it had better detection limits and was easier and quicker than the HS-SPE-based method. It has been applied to the determination of these components in 36 wine and 17 musts samples. The quantitative results suggest that the Spanish wines show meaningless amounts of these compounds. IBMP has been found just in between 1.9 and 15 ng L(-1).

  14. Determination of trace selenium in high purity tellurium by hydride generation atomic fluorescence spectrometry after solid phase extraction of a diaminobenzidine-selenium chelate

    Science.gov (United States)

    Tong, Wang; Ying, Zeng; Jinyong, Xu

    2016-09-01

    Macroporous adsorption resin was used as the sorbent for solid phase extraction and determination of the trace Se content in high purity tellurium prior to hydride generation atomic fluorescence spectrometry analysis. Selenium was converted into an organic Se chelate using 3,3‧-diaminobenzidine and was separated from the tellurium matrix by solid phase extraction. The resin was packed as a column for solid phase extraction. Under optimum conditions, trace Se can be quantitatively extracted and the tellurium matrix can be removed. The Se in the eluate was determined by hydride generation atomic fluorescence spectrometry. The limit of detection (3σ) of this method was 0.22 ng g- 1 and the relative standard deviation (RSD, n = 5) ranged from 2.0 to 2.5% for the three investigated tellurium samples. The proposed method was successfully applied for the determination of the trace Se content in high purity tellurium samples.

  15. [Simultaneous determination of four mercapturic acids in human urine using solid phase extraction and liquid chromatography-tandem mass spectrometry].

    Science.gov (United States)

    Hou, Hongwei; Xiong, Wei; Gao, Na; Song, Dongkui; Tang, Gangling; Hu, Qingyuan

    2011-01-01

    A method was developed for the simultaneous extraction and determination of four mercapturic acids (MAs), N-acetyl-S-(3,4-dihydroxybutyl)-L-cysteine (DHBMA), N-acetyl-S-(3-hydroxypropyl)-L-cysteine (3-HPMA), N-acetyl-S-(2-carboxyethyl)-L-cysteine ( CEMA) and S-phenylmercapturic acid (SPMA), in human urine using solid phase extraction and high performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS). Frozen urine samples were thawed at room temperature, and centrifuged to remove any settled precipitate. The supernatant was then purified and concentrated by a C18 solid phase extraction column, and analyzed by HPLC-MS/MS in the multiple reaction monitoring (MRM) mode for the quantitative analysis. The ranges of recovery for DHBMA, 3-HPMA, CEMA and SPMA spiked in human urine matrix at three concentration levels were 105.6%-124.4%, 102.7%-106.5%, 103.2%-103.9% and 101.7%-104.3%, respectively, with the relative standard deviations of 2.6%-7.7%. The limits of detection (LOD, S/N > or = 3) were 0. 062, 0. 031, 0. 020 and 0. 003 microg/L for DHBMA, 3-HPMA, CEMA and SPMA, respectively. The method was successfully used to detect 4 MAs in 37 human urine samples from smokers and non-smokers. It was found that the contents of 3-HPMA, CEMA and SPMA in the urines from cigarette smokers were about three to six-fold more than those in the urines from the non-smokers.

  16. Development of a selective solid phase extraction method for nitro musk compounds in environmental waters using a molecularly imprinted sorbent.

    Science.gov (United States)

    Lopez-Nogueroles, Marina; Lordel-Madeleine, Sonia; Chisvert, Alberto; Salvador, Amparo; Pichon, Valérie

    2013-06-15

    A powerful analytical method for the determination of the family of the nitro musk compounds at trace level in environmental waters-river, sea, and water from a treatment plant-is presented. The method is based on the use of molecularly imprinted silica (MIS) as sorbent for solid phase extraction (SPE) used for the clean-up and the concentration step of the target analytes previous to their determination by gas chromatography-mass spectrometry. The optimized extraction procedure allowed extraction recoveries between 61% and 87% using the MIS. The comparison with a non-imprinted silica (NIS) sorbent, for which extraction recoveries between 8% and 26% were obtained, showed the high selectivity of the MIS for the nitro musks. Moreover, high enrichment factors, ranging between 580 and 827, were achieved. The imprinted sorbent was compared to a conventional polymeric SPE sorbent for the extraction of the target compounds from environmental waters, showing high selectivity of the MIS and its clean-up potential. For the first time, the five nitro musk compounds were selectively extracted with an imprinted material.

  17. The evaluation of solid phase micro-extraction fibre types for the analysis of organic components in unburned propellant powders.

    Science.gov (United States)

    Dalby, Oliver; Birkett, Jason W

    2010-11-12

    This work describes the evaluation of various solid phase micro-extraction (SPME) fibre types for the detection of compounds originating from particles of unburned propellant powders. These compounds may also be found in association with organic gunshot residues (OGSR). Seven SPME fibres were assessed based on their ability to extract the compounds of interest (diphenylamine (DPA), 4-nitrodiphenylamine (4-NDPA), ethyl centralite (EC), nitroglycerin (NG) and dibutyl phthalate (DBP)) from four ammunition types across three calibres (9 mm, 5.56 mm and 7.62 mm). Extracts were analysed by gas chromatography/mass spectrometry (GC/MS). Results indicated that the 65 μm polydimethylsiloxane/divinylbenzene (PDMS/DVB) was the most suitable fibre type for the extraction of these compounds across the ammunition types tested. Optimal extraction time parameters were also assessed with a 35-min period determined to be suitable. A number of previously unreported considerations for extracting propellant powders and potentially OGSR related materials are discussed.

  18. A novel poly(deep eutectic solvent)-based magnetic silica composite for solid-phase extraction of trypsin.

    Science.gov (United States)

    Xu, Kaijia; Wang, Yuzhi; Li, Yixue; Lin, Yunxuan; Zhang, Haibao; Zhou, Yigang

    2016-11-23

    Novel poly(deep eutectic solvent) grafted silica-coated magnetic microspheres (Fe3O4@SiO2-MPS@PDES) were prepared by polymerization of choline chloride-itaconic acid (ChCl-IA) and γ-MPS-modified magnetic silica composites, and were characterized by vibrating sample magnetometer (VSM), Fourier transform infrared spectrometry (FT-IR), X-ray photoelectron spectra (XPS), thermal gravimetric analysis (TGA) and transmission electron microscope (TEM). Then the synthetic Fe3O4@SiO2-MPS@PDES microspheres were applied for the magnetic solid-phase extraction (MSPE) of trypsin for the first time. After extraction, the concentration of trypsin in the supernatant was determined by a UV-vis spectrophotometer. Single factor experiments were carried out to investigate the effects of the extraction process, including the concentration of trypsin, the ionic strength, the pH value, the extraction time and the temperature. Experimental results showed the extraction capacity could reach up to 287.5 mg/g under optimized conditions. In comparison with Fe3O4@SiO2-MPS, Fe3O4@SiO2-MPS@PDES displayed higher extraction capacity and selectivity for trypsin. According to the regeneration studies, Fe3O4@SiO2-MPS@PDES microspheres can be recycled six times without significant loss of its extraction capacity, and retained a high extraction capacity of 233 mg/g after eight cycles. Besides, the activity studies also demonstrated that the activity of the extracted trypsin was well retained. Furthermore, the analysis of real sample revealed that the prepared magnetic microspheres can be used to purify trypsin in crude bovine pancreas extract. These results highlight the potential of the proposed Fe3O4@SiO2-MPS@PDES-MSPE method in separation of biomolecules.

  19. Electric field-assisted solid phase extraction and cleanup of ionic compounds in complex food matrices: Fluoroquinolones in eggs.

    Science.gov (United States)

    Ribeiro, Cyntia Cabral; Orlando, Ricardo Mathias; Rohwedder, Jarbas José Rodrigues; Reyes, Felix Guillermo Reyes; Rath, Susanne

    2016-05-15

    The use of electric fields as additional driving forces in sample preparation techniques is an innovative approach that is environmentally friendly, straightforward, and able to overcome several limitations of conventional sample preparation procedures. In this work, the advantages of electric field-assisted solid phase extraction (E-SPE) using syringe-type cartridges were demonstrated for the extraction of four fluoroquinolones (FQs) in their anionic forms. The FQs were extracted from eggs and subsequently determined by UHPLC-MS/MS. The use of electric fields during the washing and final elution steps resulted in a significant improvement of the extraction efficiencies for almost all FQs when compared to conventional SPE. Intra- and inter-day assays showed coefficients of variation below 10%. The better cleanup also resulted in the appearance of less precipitated matter in the final eluate, as well as reduced matrix effects. The results showed that the electrophoretic forces derived from electric fields are a promising way of significantly increasing the extraction efficiency of ionic analytes, while minimizing matrix effects associated with complex samples. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Analysis of polybrominated diphenyl ethers in atmospheric deposition and snow samples by solid-phase disk extraction.

    Science.gov (United States)

    Quiroz, Roberto; Arellano, Lourdes; Grimalt, Joan O; Fernández, Pilar

    2008-05-23

    An extraction method for the quantitative analysis of polybrominated diphenyl ethers (PBDEs) in aqueous samples has been evaluated. The analytical methodology includes the sample filtration through glass fiber filter and subsequent extraction of dissolved phase compounds by C18 solid-phase disk extraction. Dependence of extraction efficiency on factors such as pollutant concentrations, sample volume, and stability during storage has been investigated. Mean extraction efficiencies of 97% for total PBDEs (13 tri- to heptabrominated congeners at spiking levels in the range of 15-90pg) with a RSD between 9 and 20% were achieved. Higher recoveries were observed for the more volatile PBDEs (112%) in relation to more brominated congeners (88%). The developed methodology was successfully applied to the analysis of these compounds in atmospheric deposition and snow samples from remote sites in Europe with method detection and quantitation limits in the range of 2.1-10pgL(-1) for almost all congeners, which allow the determination of PBDEs in remote areas with levels in the range of low to medium pgL(-1) for SigmaPBDEs.

  1. Magnetic nanocomposite of self-doped polyaniline-graphene as a novel sorbent for solid-phase extraction.

    Science.gov (United States)

    Mehdinia, Ali; Esfandiarnejad, Reyhaneh; Jabbari, Ali

    2015-01-01

    This work is the first study on the extraction efficiency of self-doped polyaniline that is immobilized on the graphene-modified magnetic nanoparticles. The new material was used as a sorbent for the magnetic solid-phase extraction of methyl-, propyl-, and butylparabens. The use of graphene provides a high surface area and prevents aggregation of the nanoparticles. The self-doped polyaniline also provides multifunctionality, high extraction capacity, and chemical stability even in the basic medium. The parabens were acetylated for determination by gas chromatography with flame ionization detection. The effects of monomer ratio, extraction solvent, sorbent amount, sample volume, desorption solvent volume, adsorption and desorption times, and sample ionic strength were optimized. Preconcentration factors obtained were from 190 to 310. The detection limits of the method were <2.8 μg/L. Linear ranges of the method were 5-2000 μg/L for propyl and butyl parabens, and 10-2000 μg/L for methyl paraben. The method was applied for the determination of the parabens in cosmetic products and extraction recoveries were 89-101% with RSDs ≤7.9%. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Solid phase extraction using silica gel modified with murexide for preconcentration of uranium (VI) ions from water samples

    Energy Technology Data Exchange (ETDEWEB)

    Sadeghi, S. [Department of Chemistry, Faculty of Science, Birjand University, Birjand (Iran, Islamic Republic of)], E-mail: ssadeghi@birjand.ac.ir; Sheikhzadeh, E. [Department of Chemistry, Faculty of Science, Birjand University, Birjand (Iran, Islamic Republic of)

    2009-04-30

    Murexide was chemically bonded to silica gel surface immobilized 3-aminopropyl trimethoxysilane (APMS) to produce the new sorbent. A solid phase extraction method using the new sorbent has been developed to separate and concentrate trace amount of uranium (VI) from aqueous samples for the measurement by spectrophotometry method using Arsenazo III reagent. The influences of some analytical parameters on the quantitative recoveries of the analyte were investigated both in batch and column methods. Quantitative recovery of U(VI) was achieved by stripping with 0.1 mol L{sup -1} HCl. The maximum sorption capacity of the modified silica gel was 1.13 mmol g{sup -1} U(VI). A high preconcentration factor value of 400 with a lower limit of detection of 1 {mu}g L{sup -1} was obtained for U(VI). The practical applicability of the developed sorbent was examined using synthetic and real samples such as sea/ground water samples.

  3. Analysis of polycyclic aromatic hydrocarbons in vegetable oils combining gel permeation chromatography with solid-phase extraction clean-up

    DEFF Research Database (Denmark)

    Fromberg, Arvid; Højgård, A.; Duedahl-Olesen, Lene

    2007-01-01

    of benzo[a]pyrene levels in foods laid down by the Commission of the European Communities. A survey of 69 vegetable oils sampled from the Danish market included olive oil as well as other vegetable oils such as rapeseed oil, sunflower oil, grape seed oil and sesame oil. Levels of benzo[a]pyrene in all......A semi-automatic method for the determination of polycyclic aromatic hydrocarbons (PAHs) in edible oils using a combined gel permeation chromatography/solid-phase extraction (GPC/SPE) clean-up is presented. The method takes advantage of automatic injections using a Gilson ASPEC XL sample handling...... system equipped with a GPC column (S-X3) and pre-packed silica SPE columns for the subsequent clean-up and finally gas chromatography-mass spectrometry (GC-MS) determination. The method was validated for the determination of PAHs in vegetable oils and it can meet the criteria for the official control...

  4. Solid phase extraction using silica gel modified with murexide for preconcentration of uranium (VI) ions from water samples.

    Science.gov (United States)

    Sadeghi, S; Sheikhzadeh, E

    2009-04-30

    Murexide was chemically bonded to silica gel surface immobilized 3-aminopropyl trimethoxysilane (APMS) to produce the new sorbent. A solid phase extraction method using the new sorbent has been developed to separate and concentrate trace amount of uranium (VI) from aqueous samples for the measurement by spectrophotometry method using Arsenazo III reagent. The influences of some analytical parameters on the quantitative recoveries of the analyte were investigated both in batch and column methods. Quantitative recovery of U(VI) was achieved by stripping with 0.1 mol L(-1) HCl. The maximum sorption capacity of the modified silica gel was 1.13 mmol g(-1) U(VI). A high preconcentration factor value of 400 with a lower limit of detection of 1 microg L(-1) was obtained for U(VI). The practical applicability of the developed sorbent was examined using synthetic and real samples such as sea/ground water samples.

  5. Analysis of pharmaceutical creams: a useful approach based on solid-phase extraction (SPE) and UV spectrophotometry.

    Science.gov (United States)

    Bonazzi, D; Andrisano, V; Gatti, R; Cavrini, V

    1995-10-01

    Solid-phase extraction (SPE) using C-18, diol and ion-exchange sorbents followed by UV spectrophotometric (conventional and derivative mode) assay was applied to the analysis of basic, acidic and neutral drugs commercially available in creams. A representative set of drugs (promethazine, chlorhexidine, benzydamine, ketoprofen, ibuprofen, fentiazac, piroxicam, fluorouracil, crotamiton and hydrocortisone acetate) was selected, and for each drug the appropriate SPE conditions (adsorption, washing and elution) were investigated to obtain a practical and reliable sample clean-up. It was shown that the developed SPE procedures were capable of removing interfering cream components (excipients including preservatives) allowing accurate spectrophotometric analyses to be performed. In some applications, derivative spectrophotometry was advantageous over the conventional absorption mode with respect to higher selectivity and versatility.

  6. Determination of fipronil in bovine plasma by solid-phase extraction and liquid chromatography with ultraviolet detection

    Directory of Open Access Journals (Sweden)

    Yara P. Cid

    2012-01-01

    Full Text Available A fast and efficient method has been developed and validated for the determination of fipronil in bovine plasma. Samples were subjected to solid-phase extraction (SPE followed by reversed phase liquid chromatography (LC separation, using acetonitrile/water (60:40 v/v as the mobile phase with a flow rate of 1.0 mL/min and ultraviolet (UV detection at 210 nm. Ethiprole was used as the internal standard (IS. The method was found to be linear over the range 5-500 ng/mL (r = 0.999. The limit of quantitation (LOQ was validated at 5 ng/mL. The method was successfully applied to monitor plasma concentrations following subcutaneous administration of fipronil in cattle.

  7. Multi-element pre-concentration of heavy metal ions by solid phase extraction on Chromosorb 108

    Energy Technology Data Exchange (ETDEWEB)

    Tuzen, Mustafa [Gaziosmanpasa University, Faculty of Science and Arts, Chemistry Department, 60250 Tokat (Turkey); Soylak, Mustafa [Erciyes University, Faculty of Art and Science, Department of Chemistry, 38039 Kayseri (Turkey)]. E-mail: soylak@erciyes.edu.tr; Elci, Latif [Pamukkale University, Faculty of Art and Science, Department of Chemistry, 20020 Denizli (Turkey)

    2005-08-29

    A multi-element preconcentration procedure for solid phase extraction on Chromosorb 108 as bathocuproinedisulfonic acid chelates and flame atomic absorption spectrometric determinations of some heavy metal ions in environmental samples is proposed in the present work. The influences of analytical parameters including pH of the aqueous solution, amounts of reagents, flow rates of sample and eluent solutions, sample volume etc. on the quantitative recoveries of copper, cadmium, lead, zinc, manganese, iron, chromium, nickel and cobalt ions were investigated. The effects of concomitant ions on the retentions of the analytes were also examined. The presented preconcentration procedure was applied to the determination of metal ions in reference standard materials (NRCC-SLRS 4 Riverine Water, SRM 1515 Apple leaves and GBW 07605 Tea) and some real samples including tap and river water, red wine, rice, black tea and honey.

  8. Colorimetric Solid Phase Extraction for the Measurement of Total I (Iodine, Iodide, and Triiodide) in Spacecraft Drinking Water

    Science.gov (United States)

    Lipert, Robert J.; Porter, Marc D.; Siperko, Lorraine M.; Gazda, Daniel B.; Rutz, Jeff A.; Schultz, John R.; Carrizales, Stephanie M.; McCoy, J. Torin

    2009-01-01

    An experimental drinking water monitoring kit for the measurement of iodine and silver(I) was recently delivered to the International Space Station (ISS). The kit is based on Colorimetric Solid Phase Extraction (CSPE) technology, which measures the change in diffuse reflectance of indicator disks following exposure to a water sample. To satisfy additional spacecraft water monitoring requirements, CSPE has now been extended to encompass the measurement of total I (iodine, iodide, and triiodide) through the introduction of an oxidizing agent, which converts iodide and triiodide to iodine, for measurement using the same indicator disks currently being tested on ISS. These disks detect iodine, but are insensitive to iodide and triiodide. We report here the operational considerations, design, and ground-based performance of the CSPE method for total I. The results demonstrate that CSPE technology is poised to meet NASA's total I monitoring requirements.

  9. Solid phase extraction for evaluation of occupational exposure to Pb (II) using XAD-4 sorbent prior to atomic absorption spectroscopy.

    Science.gov (United States)

    Shahtaheri, Seyed Jamaleddin; Khadem, Monireh; Golbabaei, Farideh; Rahimi-Froushan, Abbas; Ganjali, Mohammad Reza; Norouzi, Parviz

    2007-01-01

    Lead is an important constituent widely used in different industrial processes. For evaluation of workers' exposure to trace toxic metal of Pb (II), solid-phase extraction (SPE) was optimized. SPE using mini columns filled with XAD-4 resin was developed with regard to sample pH, ligand concentration, loading flow rate, elution solvent, sample volume, elution volume, the amount of resins, and sample matrix interferences. Lead ions were retained on a solid sorbent and then eluted, followed by a simple determination of analytes with flame atomic absorption spectrometery. The obtained recoveries of metal ions were greater than 92%. This method was validated with 3 different pools of spiked urine samples; it showed a good reproducibility over 6 consecutive days as well as 6 within-day experiments. This optimized method can be considered successful in simplifying sample preparation for a trace residue analysis of lead in different matrices when evaluating occupational and environmental exposures is required.

  10. Solid phase extraction of gold(III) on Amberlite XAD-2000 prior to its flame atomic absorption spectrometric determination.

    Science.gov (United States)

    Elci, Latif; Sahan, Derya; Basaran, Aydan; Soylak, Mustafa

    2007-09-01

    A solid phase extraction method for the determination of gold(III) at trace levels by flame atomic absorption spectrometer (FAAS) was developed. The method was based on retention of gold as chloro complexes through the Amberlite XAD-2000. The effect of some analytical parameters including hydrochloric acid concentration, sample volume, sample and eluent flow rates, eluent volume, eluent concentration and interfering ions on the recovery of gold(III) was investigated. The retention of gold(III) from 1.5 mol l(-1) HCl solution and the recovery of gold with 0.07 mol l(-1) NH3 solution were quantitative (>or=95%). The relative standard deviation (RSD) was calculated as 3.2% (n = 10). The detection limit for gold was 2 microg l(-1). The accuracy was checked with the determination of gold spiked an artificial seawater and a pure copper samples.

  11. Determination of Six Pyrazole Fungicides in Grape Wine by Solid-Phase Extraction and Gas Chromatography-Tandem Mass Spectrometry.

    Science.gov (United States)

    Shen, Yan; Li, Zhou; Ma, Qiang; Wang, Chuanxian; Chen, Xiangzhun; Miao, Qian; Han, Chao

    2016-05-18

    A gas chromatography-tandem mass spectrometry (GC-MS/MS) method was developed for the first simultaneous identification and quantification of six pyrazole fungicides (furametpyr, rabenzazole, fluxapyroxad, penflufen, bixafen, and isopyrazam) in grape wine samples. The grape wine samples were first diluted with water, then purified by solid-phase extraction, and finally examined by GC-MS/MS in multiple reaction monitoring (MRM) mode. Matrix-matched calibration curves were used to correct the matrix effects. The limits of quantification (LOQs), calculated as 10 times the standard deviation, were 0.2-0.8 μg kg(-1) for the six pyrazole fungicides. The average recoveries were in the range of 74.3-94.5%, with relative standard deviations (RSDs) below 5.8%, measured at three concentration levels. The proposed method is suitable for the simultaneous determination of six pyrazole fungicides in grape wine samples.

  12. Comparison of solid phase- and liquid/liquid-extraction for the purification of hair extract prior to multi-class pesticides analysis.

    Science.gov (United States)

    Duca, Radu-Corneliu; Salquebre, Guillaume; Hardy, Emilie; Appenzeller, Brice M R

    2014-04-01

    The present study focuses on the influence of a purification step - after extraction of pesticides from hair and before analysis of the extract - on the sensitivity of analytical methods including compounds from different chemical classes (both parent and metabolites). Sixty-seven pesticides and metabolites from different chemical classes were tested here: organochlorines, organophosphates, carbamates, pyrethroids, ureas, azoles, phenylpyrazoles and neonicotinoids. Two gas chromatography-negative chemical ionization-tandem mass spectrometry methods and one based on ultra-performance liquid chromatography-electrospray tandem mass spectrometry were used. Seven solid-phase extraction cartridges: C18, S-DVB, PS-DVB, GCB, GCB/PSA, SAX/PSA and Florisil/PSA were tested and compared to more classical liquid-liquid extraction procedures using ethyl acetate, hexane and dichloromethane. Although LLE allowed obtaining good results for some compounds, on the whole, SPE clearly provided better recovery for the majority of the pesticide residues tested in the present study. GCB/PSA was clearly the best suited to non-polar compounds such as organochlorines, pyrethroids and organophosphates, with recovery ranging from 45.9% (diflufenican) to 117.1% (parathion methyl). For hydrophilic metabolites (e.g. dialkyl phosphates and other organophosphate metabolites, pyrethroid metabolites, phenols and carbamate metabolites), the best results were obtained with PS-DVB, with recovery ranged from 10.3% (malathion monocarboxylic acid) to 93.1% (para-nitrophenol). For hydrophilic parent pesticides (e.g. neonicotinoids, carbamates, azoles) and metabolites without nucleophilic functions, the best recovery was obtained with SAX/PSA, with recovery ranging from 52.1% (3-hydroxycarbofuran) to 100.9% (3,4-dichloroaniline). Solid phase extraction was found to be more suitable than the liquid-liquid extraction for pesticides and their metabolites determination in terms of number of extracted compounds

  13. Determining plasma morphine levels using GC-MS after solid phase extraction to monitor drug levels in the postoperative period

    Directory of Open Access Journals (Sweden)

    Veronica Santos

    2008-01-01

    Full Text Available OBJECTIVE: To implement a selective and sensitive analytical method to quantify morphine in small volumes of plasma by gas-liquid chromatography-mass spectrometry (GC-MS, aimed at post-operatively monitoring the drug. METHOD: A gas-liquid chromatographic method with mass detection has been developed to determine morphine concentration in plasma after solid phase extraction. Morphine-d3 was used as an internal standard. Only 0.5 mL of plasma is required for the drug solid-phase extraction in the Bond Elut-Certify®, followed by the quantification of morphine derivative by GC-MS using a linear temperature program, a capillary fused silica column, and helium as the carrier and make-up gas. The method was applied to determine morphine content in plasma samples of four patients during the postoperative period of cardiac surgery. Patient-controlled analgesia with morphine was performed by a venous catheter, and a series of venous blood samples were collected. After the oro-After the orotracheal extubation, morphine plasma levels were monitored for up to 36 hours. RESULTS: The run time was 16 minutes because morphine and the internal standard were eluted after 8.8 minutes. The GC-MS method had 0.5 -1000 ng/mL linearity range (r²=0.9995, 0.1 ng/mL limit of detection, intraday and interday precision equivalent to 1.9% and 6.8%, and 0.1% and 0.8% systematic error (intraday and interday, respectively. The analytical method showed optimal absolute (98% and relative (100.7% recoveries. Morphine dose requirements and plasma levels are discussed. CONCLUSION: The analytical gas-liquid chromatography-mass spectrometry method is selective and adequate for morphine measurements in plasma for applications in clinical studies.

  14. Graphene aerogel based monolith for effective solid-phase extraction of trace environmental pollutants from water samples.

    Science.gov (United States)

    Han, Qiang; Liang, Qionglin; Zhang, Xiaoqiong; Yang, Liu; Ding, Mingyu

    2016-05-20

    Graphene aerogel (GA), a typical kind of three-dimensional (3D) macroscopic assembly, not only provides inherently excellent properties of graphene sheets (GS), but also exhibits interesting characteristics of the 3D macroporous architecture including large and tunable pore volumes, high specific surface areas and fast mass transport kinetics. Thus, it is rational to expect GA to be an efficient adsorbent for solid-phase extraction (SPE). In this paper, a novel GA monolith based solid-phase extraction method was investigated in the application of environment analysis. The GA monolith based SPE cartridge was fabricated directly in the empty cartridge through template-free "sol-cryo" method. Due to the efficient mass transfer, more adsorption sites as well as effective retention for the analytes, the adsorption property of GA for bisphenol A revealed better performance than that of GS. What's more, GA also outperformed in loading and eluting for target analysis. On the basis of the above advantages, the obtained cartridge was applied for the separation of environmental pollutants from water samples. Taking endocrine disrupting chemicals and polychlorinated biphenyls as the polar and weak polar model analytes, optimizing several parameters influencing the recoveries, limits of detection in the range of 0.01-0.11ngmL(-1) and 0.19-1.53ngL(-1) for the two series of compounds were provided by the established methods. The satisfied sensitivity was accessed and recoveries ranging from 76.3 to 112.5% were obtained for all the analytes when the proposed methods were applied in real water samples analysis. The results revealed the potential of GA as an effective sorbent in sample preparation processes.

  15. Determining plasma morphine levels using GC-MS after solid phase extraction to monitor drug levels in the postoperative period.

    Science.gov (United States)

    Santos, Veronica; López, Karin Jannet Vera; Santos, Luciana Moraes; Yonamine, Mauricio; Carmona, Maria José Carvalho; Santos, Silvia Regina Cavani Jorge

    2008-06-01

    To implement a selective and sensitive analytical method to quantify morphine in small volumes of plasma by gas-liquid chromatography-mass spectrometry (GC-MS), aimed at post-operatively monitoring the drug. A gas-liquid chromatographic method with mass detection has been developed to determine morphine concentration in plasma after solid phase extraction. Morphine-d3 was used as an internal standard. Only 0.5 mL of plasma is required for the drug solid-phase extraction in the Bond Elut-Certify, followed by the quantification of morphine derivative by GC-MS using a linear temperature program, a capillary fused silica column, and helium as the carrier and make-up gas. The method was applied to determine morphine content in plasma samples of four patients during the postoperative period of cardiac surgery. Patient-controlled analgesia with morphine was performed by a venous catheter, and a series of venous blood samples were collected. After the oro-After the orotracheal extubation, morphine plasma levels were monitored for up to 36 hours. The run time was 16 minutes because morphine and the internal standard were eluted after 8.8 minutes. The GC-MS method had 0.5 -1000 ng/mL linearity range (r(2)=0.9995), 0.1 ng/mL limit of detection, intraday and interday precision equivalent to 1.9% and 6.8%, and 0.1% and 0.8% systematic error (intraday and interday, respectively). The analytical method showed optimal absolute (98%) and relative (100.7%) recoveries. Morphine dose requirements and plasma levels are discussed. The analytical gas-liquid chromatography-mass spectrometry method is selective and adequate for morphine measurements in plasma for applications in clinical studies.

  16. A solid-phase extraction method using Transcarpathian clinoptilolite for preconcentration of trace amounts of terbium in water samples.

    Science.gov (United States)

    Vasylechko, Volodymyr O; Gryshchouk, Galyna V; Zakordonskiy, Victor P; Vyviurska, Olga; Pashuk, Andriy V

    2015-01-01

    In spite of the fact that terbium is one of the rarest elements in the Earth's crust, it is frequently used for the production of high technological materials. At the result, an effective combination of sample preparation procedure and detection method for terbium ions in different matrices is highly required. The solid-phase extraction procedure with natural Transcarpathian clinoptilolite thermally activated at 350 °C was used to preconcentrate trace amounts of terbium ions in aqueous solutions for a final spectrophotometric determination with arsenazo III. Thermogravimetric investigations confirmed the existence of relations between changes that appeared during dehydratation of calcined zeolite and its sorption affinity. Since the maximum of sorption capacity towards terbium was observed at pH 8.25, a borate buffer medium (2.5 · 10(-4) М) was used to maintain ionic force and solution acidity. Terbium was quantitatively removed from the solid-phase extraction column with a 1.0 M solution of sodium chloride (pH 2.5). The linearity of the proposed method was evaluated in the range of 2.5-200 ng · mL(-1) with detection limit 0.75 ng · mL(-1). Due to acceptable recoveries (93.3-102.0 %) and RSD values (6-7.1) from spiked tap water, the developed method can be successfully applied for the determination of trace amounts of terbium ions in the presence of major components of water. Graphical abstractSorption of terbium(III) ions on clinoptilolite.

  17. Determination of polar 1H-benzotriazoles and benzothiazoles in water by solid-phase extraction and liquid chromatography LTQ FT Orbitrap mass spectrometry

    NARCIS (Netherlands)

    van Leerdam, J.A.; Hogenboom, A.C.; van der Kooi, M.M.E.; de Voogt, P.

    2009-01-01

    A sensitive, reliable and robust method for the trace determination of six polar 1H-benzotriazoles and four benzothiazoles in drinking and surface water was developed. These compounds were extracted from water by solid-phase extraction and analyzed by Liquid Chromatography-Electrospray Mass Spectrom

  18. Streamlined sample cleanup using combined dispersive solid-phase extraction and in-vial filtration for analysis of pesticides and environmental pollutants in shrimp

    Science.gov (United States)

    A new method of sample preparation was developed and is reported for the first time. The approach combines in-vial filtration with dispersive solid-phase extraction (d-SPE) in a fast and convenient cleanup of QuEChERS (quick, easy, cheap, effective, rugged, and safe) extracts. The method was appli...

  19. New Advance of Studies on Molecularly Imprinted Solid-phase Extraction%分子印迹固相萃取技术研究新进展

    Institute of Scientific and Technical Information of China (English)

    刘祺文; 熊远福; 王锦; 文祝友; 熊海蓉; 胡红远

    2015-01-01

    随着人们对环境污染和食品安全的关注,分子印迹固相萃取技术在各领域的应用有了进一步发展.在介绍分子印迹固相萃取技术的基础上,对近年来分子印迹固相萃取技术在环境样品中农药残留的检测,食品及饲料中药物残留的检测,功能药物成分提纯及药物检测,水土环境中的其它污染物检测等4大方面的研究现状进行了综述. 同时,指出了分子印迹固相萃取技术目前存在的问题,探讨了分子印迹固相萃取技术未来的发展方向.%With attention to environmental pollution and food safety, molecular imprinted solid phase extraction technique in various fields has been further developed. Therefore, molecular imprinted solid phase extraction were briefly described in this article. Molecular imprinted solid phase extraction enrichment and detection of pesticide residues, drug residues in food and feed, other contaminants in water and soil, and also molecular imprinted solid phase extraction of drug testing and purification of functional pharmaceutical ingredient in recent years were reviewed. In this paper, the problem molecular imprinted solid phase extraction technique encountered in recent years was analyzed, and the trend of molecular imprinted solid phase extraction technique was also discussed.

  20. Sulfonated nanocellulose for the efficient dispersive micro solid-phase extraction and determination of silver nanoparticles in food products.

    Science.gov (United States)

    Ruiz-Palomero, Celia; Soriano, M Laura; Valcárcel, Miguel

    2016-01-08

    This paper reports a simple approach to Analytical Nanoscience and Nanotechnology (AN&N) that integrates the nanotool, sulfonated nanocellulose (s-NC), and nanoanalyte, silver nanoparticles (AgNPs), in the same analytical process by using an efficient, environmentally friendly dispersive micro solid-phase extraction (D-μSPE) capillary electrophoresis (CE) method with s-NC as sorbent material. Introducing negatively charged sulfate groups onto the surface of cellulose enhances its surface chemistry and enables the extraction and preconcentration of AgNPs of variable diameter (10, 20 and 60nm) and shell composition (citrate and polyvinylpyrrolidone coatings) from complex matrices into a cationic surfactant. In this way, AgNPs of diverse nature were successfully extracted onto the s-NC sorbent and then desorbed into an aqueous solution containing thiotic acid (TA) prior to CE without the need for any labor-intensive cleanup. The ensuing eco-friendly D-μSPE method exhibited a linear response to AgNPs with a limit of detection (LOD) of 20μg/L. Its ability to specifically recognize AgNPs of different sizes was checked in orange juice and mussels, which afforded recoveries of 70.9-108.4%. The repeatability of the method at the limit of quantitation (LOQ) level was 5.6%. Based on the results, sulfonated nanocellulose provides an efficient, cost-effective analytical nanotool for the extraction of AgNPs from food products. Copyright © 2015 Elsevier B.V. All rights reserved.

  1. Quantitation of low concentrations of polysorbates in high protein concentration formulations by solid phase extraction and cobalt-thiocyanate derivatization.

    Science.gov (United States)

    Kim, Justin; Qiu, Jinshu

    2014-01-02

    A spectrophotometric method was developed to quantify low polysorbate (PS) levels in biopharmaceutical formulations containing high protein concentrations. In the method, Oasis HLB solid phase extraction (SPE) cartridge was used to extract PS from high protein concentration formulations. After loading a sample, the cartridge was washed with 4M guanidine HCl and 10% (v/v) methanol, and the retained PS was eluted by acetonitrile. Following the evaporation of acetonitrile, aqueous cobalt-thiocyanate reagent was added to react with the polyoxyethylene oxide chain of polysorbates to form a blue colored PS-cobaltothiocyante complex. This colored complex was then extracted into methylene chloride and measured spectrophotometrically at 620 nm. The method performance was evaluated on three products containing 30-40 mg L(-1) PS-20 and PS-80 in ≤70 g L(-1) protein formulations. The method was specific (no matrix interference identified in three types of protein formulations), sensitive (quantitation limit of 10 mg L(-1) PS) and robust with good precision (relative standard deviation ≤6.4%) and accuracy (spike recoveries from 95% to 101%). The linear range of the method for both PS-20 and PS-80 was 10 to 80 mg L(-1) PS. By diluting samples with 6M guanidine HCl and/or using different methylene chloride volumes to extract the colored complexes of standards and samples, the method could accurately and precisely quantify 40 mg L(-1) PS in up to 300 g L(-1) protein formulations.

  2. Micro-solid-phase extraction of organochlorine pesticides using porous metal-organic framework MIL-101 as sorbent.

    Science.gov (United States)

    Huang, Zhenzhen; Lee, Hian Kee

    2015-07-03

    In this study, a metal-organic framework material, MIL-101, used as a micro-solid-phase extraction (μ-SPE) sorbent for efficient enrichment of five organochlorine pesticides (OCPs), including α-HCH, Aldrin, α-Chlordane, Dieldrin and p,p'-DDD from water samples, followed by gas chromatography-mass spectrometry, is reported. This study demonstrated a new application of MIL-101 using μ-SPE, an advantage of the latter being its ability to process complex aqueous matrices, due to the protection of the sorbent afforded by the hollow fiber membrane bag. Key factors affecting extraction efficiency were studied, including elution solvent, extraction and desorption time. Under the optimal extraction conditions, the calibration plots were linear from 0.05 to 50 ng/mL for α-HCH and p,p'-DDD, and 0.1 to 50 ng/mL for the other three analytes. The limits of detection were between 0.0025 and 0.016 ng/mL. The relative recoveries of the OCPs spiked into real water samples (at 5 ng/mL of each analyte) ranged from 87.6 to 98.6% with relative standard deviations of <10%.

  3. Application of mesoporous carbon as a solid-phase microextraction fiber coating for the extraction of volatile aromatic compounds.

    Science.gov (United States)

    Zhang, Xi; Zang, Xiaohuan; Zhang, Guijiang; Wang, Chun; Wang, Zhi

    2015-08-01

    A mesoporous carbon was fabricated using MCM-41 as a template and sucrose as a carbon source. The carbon material was coated on stainless-steel wires by using the sol-gel technique. The prepared solid-phase microextraction fiber was used for the extraction of five volatile aromatic compounds (chlorobenzene, ethylbenzene, o-xylene, bromobenzene, and 4-chlorotoluene) from tea beverage samples (red tea and green tea) prior to gas chromatography with mass spectrometric detection. The main experimental parameters affecting the extraction of the volatile aromatic compounds by the fiber, including the extraction time, sample volume, extraction temperature, salt addition, and desorption conditions, were investigated. The linearity was observed in the range from 0.1 to 10.0 μg/L with the correlation coefficients (r) ranging from 0.9923 to 0.9982 and the limits of detection were less than 10.0 ng/L. The recoveries of the volatile aromatic compounds by the method from tea beverage samples at spiking levels of 1.0 and 10.0 μg/L ranged from 73.1 to 99.1%.

  4. Volatile flavour constituent patterns of Terras Madeirenses red wines extracted by dynamic headspace solid-phase microextraction.

    Science.gov (United States)

    Perestrelo, Rosa; Caldeira, Michael; Rodrigues, Freddy; Câmara, José S

    2008-06-01

    A suitable analytical procedure based on static headspace solid-phase microextraction (SPME) followed by thermal desorption gas chromatography-ion trap mass spectrometry detection (GC-(ITD)MS), was developed and applied for the qualitative and semi-quantitative analysis of volatile components of Portuguese Terras Madeirenses red wines. The headspace SPME method was optimised in terms of fibre coating, extraction time, and extraction temperature. The performance of three commercially available SPME fibres, viz. 100 mum polydimethylsiloxane; 85 mum polyacrylate, PA; and 50/30 mum divinylbenzene/carboxen on polydimethylsiloxane, was evaluated and compared. The highest amounts extracted, in terms of the maximum signal recorded for the total volatile composition, were obtained with a PA coating fibre at 30 degrees C during an extraction time of 60 min with a constant stirring at 750 rpm, after saturation of the sample with NaCl (30%, w/v). More than sixty volatile compounds, belonging to different biosynthetic pathways, have been identified, including fatty acid ethyl esters, higher alcohols, fatty acids, higher alcohol acetates, isoamyl esters, carbonyl compounds, and monoterpenols/C(13)-norisoprenoids.

  5. Iron oxide functionalized graphene nano-composite for dispersive solid phase extraction of chemical warfare agents from aqueous samples.

    Science.gov (United States)

    Chinthakindi, Sridhar; Purohit, Ajay; Singh, Varoon; Tak, Vijay; Goud, D Raghavender; Dubey, D K; Pardasani, Deepak

    2015-05-15

    Present study deals with the preparation and evaluation of graphene based magnetic nano-composite for dispersive solid phase extraction of Chemical Weapons Convention (CWC) relevant chemicals from aqueous samples. Nano-composite, Fe3O4@SiO2-G was synthesized by covalently bonding silica coated Fe3O4 onto the graphene sheets. Nerve agents (NA), Sulfur mustard (SM) and their non-toxic environmental markers were the target analytes. Extraction parameters like amount of sorbent, extraction time and desorption conditions were optimized. Dispersion of 20 milligram of sorbent in 200mL of water sample for 20min. followed by methanol/chloroform extraction produced average to good recoveries (27-94%) of targeted analytes. Recoveries of real agents exhibited great dependency upon sample pH and ionic strength. Sarin produced maximum recovery under mild acidic conditions (56% at pH 5) while VX demanded alkaline media (83% at pH 9). Salts presence in the aqueous samples was found to be advantageous, raising the recoveries to as high as 94% for SM. Excellent limits of detection (LOD) for sulphur mustard and VX (0.11ngmL(-1) and 0.19ngmL(-1) respectively) proved the utility of the developed method for the off-site analysis of CWC relevant chemicals.

  6. Development of a new analytical method for the determination of red beetroot betalains using dispersive solid-phase extraction.

    Science.gov (United States)

    Sawicki, Tomasz; Surma, Magdalena; Zieliński, Henryk; Wiczkowski, Wiesław

    2016-08-01

    The objective of this study was to develop a method for the determination of red beetroot betalains based on the dispersive solid-phase extraction and modified QuEChERS methods followed by micro-high performance liquid chromatography coupled with a mass spectrometer that was equipped with a quadrupole and time-of-flight detector. Currently, new techniques for the extraction of the pigments are necessary and in this study, an extraction of beetroot betalains based on the QuEChERS method was developed for the first time. Twelve variants of the methods with different sorbent combinations were tested. The extraction with 15% methanol and with 0.05% formic acid was performed as a reference method to compare the obtained results. In all of the samples with the addition of sorbents, a lower noise was demonstrated in the obtained results. The betalain concentrations obtained using the tested methods were 0.32-0.54 mg g(-1) , while the value of the reference method was 0.44 mg g(-1) . The method that used the strong ion exchange sorbent (0.44±0.05 mg g(-1) ) was the most adequate in terms of analyzed content, related standard deviation value and interference compared to the reference method. It was concluded that the properly modified QuEChERS method can be successfully applied for the determination of red beetroot betalains. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. [Analysis of pesticide multiresidues in rice by gas chromatography-mass spectrometry coupled with solid phase extraction].

    Science.gov (United States)

    Liu, Pengyan; Liu, Qingxue; Ma, Yusong; Liu, Jinwei; Jia, Xuan

    2006-05-01

    A new analytical method was developed to simultaneously determine multiple pesticide residues in rice including organophosphorus, organochlorine, carbamate and pyrethroid. First, the solvents for pesticide extraction were selected for optimization. Eight solvents were screened to find that the extraction efficiency with dichloromethane was the best. Second, clean-up was performed by solid phase extraction using a Florisil cartridge. Various mixtures of hexane and acetone were tested to show that the mixture of hexane-acetone (4:1, v/v) had the best performance. The clean-up helped the sample purification significantly. The prepared sample was analyzed using gas chromatography-mass spectrometry (GC-MS) in selected ion monitoring (SIM) mode. The pesticides were identified with retention time and selected ions and their relative abundances, and they were quantified based on extract of spiking standards in a blank sample. The limits of detection (LODs) were evaluated on the values of the lower concentration fortified sample under the signal-to-noise ratio of 3:1. The recoveries and relative standard deviations (RSDs) were checked by adding pesticide standard solution at two levels to untreated samples, and the triplicate analysis of the samples were carried out for each spiked level. The LODs were at microg/kg level. The average recoveries of most pesticides were from 75% to 120 %. The RSDs were less than 10.4% (n = 3). These results indicated that this method is simple, rapid, sensitive for the simultaneous determination requirements of multiple pesticide residues in rice.

  8. Magnetic multiwall carbon nanotubes modified with dual hydroxy functional ionic liquid for the solid-phase extraction of protein.

    Science.gov (United States)

    Chen, Jing; Wang, Yuzhi; Huang, Yanhua; Xu, Kaijia; Li, Na; Wen, Qian; Zhou, Yigang

    2015-05-21

    A novel adsorbent based on silica-coated magnetic multiwall carbon nanotubes (MWCNTs) surface modified by dual hydroxy functional ionic liquid (FIL) ([OH]-FIL-m-MWCNTs@SiO2) has been designed and used for the purification of lysozyme (Lys) by magnetic solid-phase extraction (MSPE). Fourier transform infrared spectroscopy (FTIR), a vibrating sample magnetometer (VSM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and thermogravimetric analysis (TGA) were employed to characterize [OH]-FIL-m-MWCNTs@SiO2. After extraction, the concentration of Lys was determined by a UV-Vis spectrophotometer at 278 nm. A series of single-factor experiments were carried out to identify the optimal conditions of the extraction and the extraction amount could reach up to 94.6 mg g(-1). The RSD of the precision, the repeatability and the stability experiments were 0.37% (n = 3), 0.47% (n = 3) and 0.52% (n = 3), respectively. Comparison of [OH]-FIL-m-MWCNTs@SiO2 with silica-coated magnetic Fe3O4 (Fe3O4@SiO2), silica-coated magnetic multiwall carbon nanotubes (m-MWCNTs@SiO2) and alkyl quaternary ammonium ionic liquid-modified on m-MWCNTs@SiO2 was carried out by extracting Lys. The extraction of bovine serum albumin (BSA), trypsin (Try) and ovalbumin (OVA) was also done by the proposed method. Desorption of Lys was carried out by 0.005 mol L(-1) Na2HPO4-1 mol L(-1) NaCl as the eluent solution and the desorption ratio reached 91.6%. Nearly 97.8% of the [OH]-FIL-m-MWCNTs@SiO2 could be recovered from each run, and the extraction amount decreased less after five runs. The circular dichroism spectral experiment analysis indicated that the secondary structure of Lys was unchanged after extraction.

  9. Magnetic graphene oxide modified with choline chloride-based deep eutectic solvent for the solid-phase extraction of protein.

    Science.gov (United States)

    Huang, Yanhua; Wang, Yuzhi; Pan, Qi; Wang, Ying; Ding, Xueqin; Xu, Kaijia; Li, Na; Wen, Qian

    2015-06-02

    Four kinds of green deep eutectic solvents (DESs) based on choline chloride (ChCl) have been synthesized and coated on the surface of magnetic graphene oxide (Fe3O4@GO) to form Fe3O4@GO-DES for the magnetic solid-phase extraction of protein. X-ray diffraction (XRD), vibrating sample magnetometer (VSM), Fourier transform infrared spectrometry (FTIR), field emission scanning electron microscopy (FESEM) and thermal gravimetric analysis (TGA) were employed to characterize Fe3O4@GO-DES, and the results indicated the successful preparation of Fe3O4@GO-DES. The UV-vis spectrophotometer was used to measure the concentration of protein after extraction. Single factor experiments proved that the extraction amount was influenced by the types of DESs, solution temperature, solution ionic strength, extraction time, protein concentration and the amount of Fe3O4@GO-DES. Comparison of Fe3O4@GO and Fe3O4@GO-DES was carried out by extracting bovine serum albumin, ovalbumin, bovine hemoglobin and lysozyme. The experimental results showed that the proposed Fe3O4@GO-DES performs better than Fe3O4@GO in the extraction of acidic protein. Desorption of protein was carried out by eluting the solid extractant with 0.005 mol L(-1) Na2HPO4 contained 1 mol L(-1) NaCl. The obtained elution efficiency was about 90.9%. Attributed to the convenient magnetic separation, the solid extractant could be easily recycled.

  10. Simultaneous determination of phenolic compounds in Equisetum palustre L. by ultra high performance liquid chromatography with tandem mass spectrometry combined with matrix solid-phase dispersion extraction.

    Science.gov (United States)

    Wei, Zuofu; Pan, Youzhi; Li, Lu; Huang, Yuyang; Qi, Xiaolin; Luo, Meng; Zu, Yuangang; Fu, Yujie

    2014-11-01

    A method based on matrix solid-phase dispersion extraction followed by ultra high performance liquid chromatography with tandem mass spectrometry is presented for the extraction and determination of phenolic compounds in Equisetum palustre. This method combines the high efficiency of matrix solid-phase dispersion extraction and the rapidity, sensitivity, and accuracy of ultra high performance liquid chromatography with tandem mass spectrometry. The influential parameters of the matrix solid-phase dispersion extraction were investigated and optimized. The optimized conditions were as follows: silica gel was selected as dispersing sorbent, the ratio of silica gel to sample was selected to be 2:1 (400/200 mg), and 8 mL of 80% methanol was used as elution solvent. Furthermore, a fast and sensitive ultra high performance liquid chromatography with tandem mass spectrometry method was developed for the determination of nine phenolic compounds in E. palustre. This method was carried out within <6 min, and exhibited satisfactory linearity, precision, and recovery. Compared with ultrasound-assisted extraction, the proposed matrix solid-phase dispersion procedure possessed higher extraction efficiency, and was more convenient and time saving with reduced requirements on sample and solvent amounts. All these results suggest that the developed method represents an excellent alternative for the extraction and determination of active components in plant matrices.

  11. Polypyrrole-magnetite dispersive micro-solid-phase extraction combined with ultraviolet-visible spectrophotometry for the determination of rhodamine 6G and crystal violet in textile wastewater.

    Science.gov (United States)

    Kamaruddin, Amirah Farhan; Sanagi, Mohd Marsin; Wan Ibrahim, Wan Aini; Md Shukri, Dyia S; Abdul Keyon, Aemi S

    2017-08-29

    Polypyrrole-magnetite dispersive micro-solid-phase extraction method combined with ultraviolet-visible spectrophotometry was developed for the determination of selected cationic dyes in textile wastewater. Polypyrrole-magnetite was used as adsorbent due to its thermal stability, magnetic properties, and ability to adsorb Rhodamine 6G and crystal violet. Dispersive micro-solid-phase extraction parameters were optimized, including sample pH, adsorbent amount, extraction time, and desorption solvent. The optimum polypyrrole-magnetite dispersive micro-solid phase-extraction conditions were sample pH 8, 60 mg polypyrrole-magnetite adsorbent, 5 min of extraction time, and acetonitrile as the desorption solvent. Under the optimized conditions, the polypyrrole-magnetite dispersive micro-solid-phase extraction with ultraviolet-visible method showed good linearity in the range of 0.05-7 mg/L (R(2)  > 0.9980). The method also showed a good limit of detection for the dyes (0.05 mg/L) and good analyte recoveries (97.4-111.3%) with relative standard deviations extraction and determination of dyes at trace concentration levels. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Hybrid organic-inorganic silica monolith with hydrophobic/strong cation-exchange functional groups as a sorbent for micro-solid phase extraction.

    Science.gov (United States)

    Zheng, Ming-Ming; Ruan, Ge-Deng; Feng, Yu-Qi

    2009-11-06

    A hybrid organic-inorganic silica monolith with hydrophobic and strong cation-exchange functional groups was prepared and used as a sorbent for micro-solid phase extraction (micro-SPE). The hybrid silica monolith functionalized with octyl and thiol groups was conveniently synthesized by hydrolysis and polycondensation of a mixture of tetraethoxysilane (TEOS), n-octyltriethoxysilane (C8-TEOS) and 3-mercaptopropyltrimethoxysilane (MPTMS) via a two-step catalytic sol-gel process. Due to the favorable chemical reactivity of mercapto pendant moieties, the obtained hybrid monolith was oxidized using hydrogen peroxide (30%, w/w) to yield sulfonic acid groups, which provided strong cation-exchange sites. The obtained hybrid monolith was characterized by diffused infrared spectroscopy, elemental analysis, scanning electron microscopy and mercury intrusion porosimetry. The results show that the resulting monolith contains much higher carbon (31.6%) and sulfur (4.8%) contents than traditionally bonded silica materials. The extraction performance of the hybrid monolith was evaluated using sulfonamides as testing analytes by micro-SPE on-line coupled to HPLC. The results show that the hybrid monolith with hydrophobic and strong cation-exchange functional groups exhibits high extraction efficiency towards the testing analytes. The column-to-column RSD values were 1.3-9.8% for the extraction of SAs investigated. The extraction performance of the hybrid silica monolith remained practically unchanged after treated with acid (pH 1.0) and basic solutions (pH 10.5). Finally, the application of the hybrid monolith was demonstrated by micro-SPE of sulfonamide residues from milk followed by HPLC-UV analysis. The limits of detection (S/N=3) for eight SAs were found to be 1.0-3.0ng/mL in milk. The recoveries of eight SAs spiked in milk sample ranged from 80.2% to 115.6%, with relative standard deviations less than 11.8%.

  13. Selective mixed-bed solid phase extraction of atrazine herbicide from environmental water samples using molecularly imprinted polymer.

    Science.gov (United States)

    Zarejousheghani, Mashaalah; Fiedler, Petra; Möder, Monika; Borsdorf, Helko

    2014-11-01

    A novel approach for the selective extraction of organic target compounds from water samples has been developed using a mixed-bed solid phase extraction (mixed-bed SPE) technique. The molecularly imprinted polymer (MIP) particles are embedded in a network of silica gel to form a stable uniform porous bed. The capabilities of this method are demonstrated using atrazine as a model compound. In comparison to conventional molecularly imprinted-solid phase extraction (MISPE), the proposed mixed-bed MISPE method in combination with gas chromatography-mass spectrometry (GC-MS) analysis enables more reproducible and efficient extraction performance. After optimization of operational parameters (polymerization conditions, bed matrix ingredients, polymer to silica gel ratio, pH of the sample solution, breakthrough volume plus washing and elution conditions), improved LODs (1.34 µg L(-1) in comparison to 2.25 µg L(-1) obtained using MISPE) and limits of quantification (4.5 µg L(-1) for mixed-bed MISPE and 7.5 µg L(-1) for MISPE) were observed for the analysis of atrazine. Furthermore, the relative standard deviations (RSDs) for atrazine at concentrations between 5 and 200 µg L(-1) ranged between 1.8% and 6.3% compared to MISPE (3.5-12.1%). Additionally, the column-to-column reproducibility for the mixed-bed MISPE was significantly improved to 16.1%, compared with 53% that was observed for MISPE. Due to the reduced bed-mass sorbent and at optimized conditions, the total amount of organic solvents required for conditioning, washing and elution steps reduced from more than 25 mL for conventional MISPE to less than 2 mL for mixed-bed MISPE. Besides reduced organic solvent consumption, total sample preparation time of the mixed-bed MISPE method relative to the conventional MISPE was reduced from more than 20 min to less than 10 min. The amount of organic solvent required for complete elution diminished from 3 mL (conventional MISPE) to less than 0.4 mL with the mixed

  14. Sol–gel-based silver nanoparticles-doped silica – Polydiphenylamine nanocomposite for micro-solid-phase extraction

    Energy Technology Data Exchange (ETDEWEB)

    Bagheri, Habib, E-mail: bagheri@sharif.edu; Banihashemi, Solmaz

    2015-07-30

    A nanocomposite of silica-polydiphenylamine doped with silver nanoparticles (Ag–SiO{sub 2}-PDPA) was successfully synthesized by the sol–gel process. For its preparation, PDPA was mixed with butanethiol capped Ag nanoparticles (NPs) and added to the silica sol solution. The Ag NPs were stabilized as a result of their adsorption on the SiO{sub 2} spheres. The surface characteristic of nanocomposite was investigated using scanning electron microscopy (SEM). In this work the Ag–SiO{sub 2}-PDPA nanocomposite was employed as an efficient sorbent for micro-solid-phase extraction (μ-SPE) of some selected pesticides. An amount of 15 mg of the prepared sorbent was used to extract and determine the representatives from organophosphorous, organochlorine and aryloxyphenoxy propionic acids from aqueous samples. After the implementation of extraction process, the analytes were desorbed by methanol and determined using gas chromatography–mass spectrometry (GC–MS). Important parameters influencing the extraction and desorption processes such as pH of sample solution, salting out effect, type and volume of the desorption solvent, the sample loading and eluting flow rates along with the sample volume were experimentally optimized. Limits of detection (LODs) and the limits of quantification (LOQs) were in the range of 0.02–0.05 μg L{sup −1} and 0.1–0.2 μg L{sup −1}, respectively, using time scheduled selected ion monitoring (SIM) mode. The relative standard deviation percent (RSD %) with four replicates was in the range of 6–10%. The applicability of the developed method was examined by analyzing different environmental water samples and the relative recovery (RR %) values for the spiked water samples were found to be in the range of 86–103%. - Highlights: • A sol–gel-based silver nanoparticles doped silica-polydiphenylamine nanocomposite was synthesized. • The sorbent was applied to micro-solid-phase extraction of some selected pesticides in water

  15. Preparation and selective recognition of a novel solid-phase microextraction fiber combined with molecularly imprinted polymers for the extraction of parabens in soy sample.

    Science.gov (United States)

    He, Juan; Chen, Si; Jiang, Yili; Shen, Yanzheng; Zhu, Jing; Wei, Hongliang; Zhang, Hongxia; Lu, Kui

    2012-01-01

    A prepared molecularly imprinted polymer with ethyl p-hydroxybenzoate as template molecule was applied for the first time to a homemade solid-phase microextraction fiber. The molecularly imprinted polymer-coated solid-phase microextraction fiber was characterized by scanning electron microscopy and thermogravimetric analysis. Various parameters were investigated, including extraction temperature, extraction time, and desorption time. Under the optimum extraction conditions, the molecularly imprinted polymer-coated solid-phase microextraction fiber exhibited higher selectivity with greater extraction capacity toward parabens compared with the nonimprinted polymer-coated solid-phase microextraction fiber and commercial fibers. The molecularly imprinted polymer-coated solid-phase microextraction fiber was tested using gas chromatography to determine parabens, including methyl p-hydroxybenzoate, ethyl p-hydroxybenzoate, and propyl p-hydroxybenzoate. The linear ranges were 0.01-10 μg/mL with a correlation coefficient above 0.9943. The detection limits (under signal-to-noise ratio of 3) were below 0.30 μg/L. The fiber was successfully applied to the simultaneous analysis of three parabens in spiked soy samples with satisfactory recoveries of 95.48, 97.86, and 92.17%, respectively. The relative standard deviations (n=6) were within 2.83-3.91%. The proposed molecularly imprinted polymer-coated solid-phase microextraction method is suitable for selective extraction and determination of trace parabens in food samples. Copyright © 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Synthesis of a molecularly imprinted polymer for the solid-phase extraction of betulin and betulinic acid from plane bark.

    Science.gov (United States)

    Claude, Berengere; Viron-Lamy, Cecile; Haupt, Karsten; Morin, Philippe

    2010-01-01

    Plant extracts are usually complex mixtures of various polarity compounds and their study often includes a purification step, such as solid-phase extraction (SPE), to isolate interest compounds prior analytical investigations. Molecularly imprinted polymers (MIPs) are a new promising type of SPE material which offer tailor-made selectivity for the extraction of trace active components in complex matrices. Numerous specific cavities that are sterically and chemically complementary of the target molecules, are formed in imprinted polymers. A molecularly imprinted polymer (MIP) was synthesised in order to trap a specific class of triterpene, including betulin and betulinic acid from a methanolic extract of plane bark. Imprinted polymers were synthesised by thermal polymerisation of betulin as template, methacrylic acid (MAA) or acrylamide (AA) as functional monomer, ethylene glycol dimethacrylate as crosslinking agent and chloroform as porogen. Afterwards, MAA- and AA-MIPs were compared with their non-imprinted polymers (NIPs) in order to assess the selectivity vs betulin and its derivatives. Recovered triterpenes were analysed by HPLC during MIP-SPE protocol. After SPE optimisation, the MAA-imprinted polymer exhibited highest selectivity and recovery (better than 70%) for betulin and best affinity for its structural analogues. Thus, a selective washing step (chloroform, acetonitrile) removed unwanted matrix compounds (fatty acids) from the SPE cartridge. The elution solvent was methanol. Finally, the MAA-MIP was applied to fractionate a plane bark methanolic extract containing betulin and betulinic acid. This study demonstrated the possibility of direct extraction of betulin and its structural analogues from plant extracts by MIP technology.

  17. Ionic liquid-functionalized silica for selective solid-phase extraction of organic acids, amines and aldehydes.

    Science.gov (United States)

    Vidal, Lorena; Parshintsev, Jevgeni; Hartonen, Kari; Canals, Antonio; Riekkola, Marja-Liisa

    2012-02-24

    Three ionic liquid (IL)-functionalized silica materials, imidazolium, N-methylimidazolium and 1-alkyl-3-(propyl-3-sulfonate) imidazolium, were synthesised and applied in solid-phase extraction (SPE) of organic acids, amines and aldehydes, which are important compound families in atmospheric aerosol particles. 1-Alkyl-3-(propyl-3-sulfonate) imidazolium-functionalized silica was tested as sorbent for SPE for the first time. The analytes were separated and detected by liquid chromatography-mass spectrometry (LC-MS). To confirm the results achieved by LC-MS, the acids were additionally determined by gas chromatography-mass spectrometry (GC-MS). The stability of the IL-functionalized silica materials was tested at low and high pH. The effect of the pH on the extraction was also informative of the retention mechanism of the materials. The results showed anion exchange to be the main interaction, but hydrophobic and π interactions and hydrogen bonding also played a role in the extraction. Extraction efficiencies for organic acids ranged from 87 to 110%, except for cis-pinonic acid (19-29%). Lower extraction efficiencies for amines and aldehydes confirmed that anionic exchange was the predominant interaction. Comparisons made with two commercial SPE materials--silica-based strong anion exchange (SAX) and polymer-based mixed-mode anion exchange and reverse-phase (MAX)--showed the IL-functionalized materials to offer different selectivity and better extraction efficiency than SAX for aromatic compounds. Finally, the new materials were successfully tested in the extraction of an atmospheric aerosol sample.

  18. Solid-phase extraction-spectrophotometric determination of uranium(VI) in natural waters

    Energy Technology Data Exchange (ETDEWEB)

    Sadeghi, Susan; Mohammadzadeh, Darush [Department of Chemistry, University of Birjand, Birjand (Iran); Yamini, Yadollah [Department of Chemistry, Tarbiat Moddars University, Tehran (Iran)

    2003-03-01

    A method for the extraction and determination of uranyl ion in natural waters using octadecyl bonded silica membrane disks modified with piroxicam and spectrophotometry with arsenazo(III) is proposed. The perconcentration step was studied with regard to experimental parameters such as amount of extractant, type and amount of eluent, pH, flow rates and tolerance limit of diverse ions on the recovery of uranyl ion. The limit of detection of the proposed method is 0.4 {mu}g L{sup -1} of uranyl. The method was applied to the recovery of uranyl from different water samples. (orig.)

  19. Matrix molecularly imprinted mesoporous sol–gel sorbent for efficient solid-phase extraction of chloramphenicol from milk

    Energy Technology Data Exchange (ETDEWEB)

    Samanidou, Victoria, E-mail: samanidu@chem.auth.gr [Laboratory of Analytical Chemistry, Department of Chemistry, Aristotle University of Thessaloniki (Greece); Kehagia, Maria [Laboratory of Analytical Chemistry, Department of Chemistry, Aristotle University of Thessaloniki (Greece); Kabir, Abuzar, E-mail: akabir@fiu.edu [International Forensic Research Institute, Department of Chemistry and Biochemistry, Florida International University, Miami, FL (United States); Furton, Kenneth G. [International Forensic Research Institute, Department of Chemistry and Biochemistry, Florida International University, Miami, FL (United States)

    2016-03-31

    Highly selective and efficient chloramphenicol imprinted sol–gel silica based inorganic polymeric sorbent (sol–gel MIP) was synthesized via matrix imprinting approach for the extraction of chloramphenicol in milk. Chloramphenicol was used as the template molecule, 3-aminopropyltriethoxysilane (3-APTES) and triethoxyphenylsilane (TEPS) as the functional precursors, tetramethyl orthosilicate (TMOS) as the cross-linker, isopropanol as the solvent/porogen, and HCl as the sol–gel catalyst. Non-imprinted sol–gel polymer (sol–gel NIP) was synthesized under identical conditions in absence of template molecules for comparison purpose. Both synthesized materials were characterized by Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FT-IR) and nitrogen adsorption porosimetry, which unambiguously confirmed their significant structural and morphological differences. The synthesized MIP and NIP materials were evaluated as sorbents for molecularly imprinted solid phase extraction (MISPE) of chloramphenicol in milk. The effect of critical extraction parameters (flow rate, elution solvent, sample and eluent volume, selectivity coefficient, retention capacity) was studied in terms of retention and desorption of chloramphenicol. Competition and cross reactivity tests have proved that sol–gel MIP sorbent possesses significantly higher specific retention and enrichment capacity for chloramphenicol compared to its non-imprinted analogue. The maximum imprinting factor (IF) was found as 9.7, whereas the highest adsorption capacity of chloramphenicol by sol–gel MIP was 23 mg/g. The sol–gel MIP was found to be adequately selective towards chloramphenicol to provide the necessary minimum required performance limit (MRPL) of 0.3 μg/kg set forth by European Commission after analysis by LC-MS even without requiring time consuming solvent evaporation and sample reconstitution step, often considered as an integral part in solid phase extraction work

  20. Determination of five pyrethroids in tea drinks by dispersive solid phase extraction with polyaniline-coated magnetic particles.

    Science.gov (United States)

    Wang, Yuanpeng; Sun, Ying; Gao, Yan; Xu, Bo; Wu, Qiong; Zhang, Hanqi; Song, Daqian

    2014-02-01

    The polyaniline-coated magnetic particles with bowl-shaped morphology (Fe3O4/C/PANI microbowls) were successfully prepared and characterized by scanning electron microscopy, transmission electron microscopy and vibrating sample magnetometry. The prepared microbowls were used as the magnetic adsorbent in dispersive solid phase extraction of five pyrethroids, including cyhalothrin, beta-cypermethrin, esfenvalerate, permethrin and bifenthrin in plain tea drinks. The effects of experiment factors, including amount of Fe3O4/C/PANI microbowls, pH value, ultrasound extraction time and desorption conditions, were investigated. The extraction recoveries obtained with 8 mg of magnetic microbowls were satisfactory, and the microbowls can be reused after easy washing. Thus, a simple, selective and effective method for the determination of the pyrethroids was established successfully. The results showed that the method had good linearity (r=0.9992-0.9998), and the limits of detections (LODs) were from 0.025 to 0.032 ng mL(-1). The intra-day and inter-day relative standard deviations (RSDs) were in the range of 2.4-6.1% and 3.5-8.8%, respectively. Recoveries obtained by analyzing the real tea drinks were in the range of 72.1-118.4%.

  1. Using pollen grains as novel hydrophilic solid-phase extraction sorbents for the simultaneous determination of 16 plant growth regulators.

    Science.gov (United States)

    Lu, Qian; Wu, Jian-Hong; Yu, Qiong-Wei; Feng, Yu-Qi

    2014-11-01

    In this article, pollen grains were for the first time used as a hydrophilic solid-phase extraction (HILIC-SPE) sorbent for the determination of 16 plant growth regulators (PGRs) in fruits and vegetables. Fourier transform infrared spectroscopy (FT-IR), scanning electronic microscopy (SEM) and nitrogen sorption porosimetry (NSP) were used to investigate the chemical structure and the surface properties of the pollen grains. Pollen grains exhibited an excellent adsorption capacity for some polar compounds due to their particular functional groups. Several parameters influencing extraction performance were investigated. A green and simple HILIC-SPE-method using pollen grain cartridge for purification of fruit and vegetable extractions, followed by ultra-high performance liquid chromatography-triple quadrupole tandem mass spectrometry (UHPLC-MS/MS) was established. Good linear relationships were obtained for 16 PGRs with correlation coefficients (R) above 0.9980. The limits of detection (LODs) of 16 PGRs in cucumber were in the range of 0.01-1.10 μg · kg(-1). Reproducibility of the method was evaluated by intra-day and inter-day precisions with relative standard deviations (RSDs), which were less than 14.4%. We successfully applied this methodology to analyze 16 PGRs in 8 different kinds of fruits and vegetables. The recoveries from samples spiked with 16 PGRs were from 80.5% to 119.2%, with relative standard deviations less than 15.0%.

  2. Metal-organic framework mixed-matrix disks: Versatile supports for automated solid-phase extraction prior to chromatographic separation.

    Science.gov (United States)

    Ghani, Milad; Font Picó, Maria Francesca; Salehinia, Shima; Palomino Cabello, Carlos; Maya, Fernando; Berlier, Gloria; Saraji, Mohammad; Cerdà, Víctor; Turnes Palomino, Gemma

    2017-03-10

    We present for the first time the application of metal-organic framework (MOF) mixed-matrix disks (MMD) for the automated flow-through solid-phase extraction (SPE) of environmental pollutants. Zirconium terephthalate UiO-66 and UiO-66-NH2 MOFs with different size (90, 200 and 300nm) have been incorporated into mechanically stable polyvinylidene difluoride (PVDF) disks. The performance of the MOF-MMDs for automated SPE of seven substituted phenols prior to HPLC analysis has been evaluated using the sequential injection analysis technique. MOF-MMDs enabled the simultaneous extraction of phenols with the concomitant size exclusion of molecules of larger size. The best extraction performance was obtained using a MOF-MMD containing 90nm UiO-66-NH2 crystals. Using the selected MOF-MMD, detection limits ranging from 0.1 to 0.2μgL(-1) were obtained. Relative standard deviations ranged from 3.9 to 5.3% intra-day, and 4.7-5.7% inter-day. Membrane batch-to-batch reproducibility was from 5.2 to 6.4%. Three different groundwater samples were analyzed with the proposed method using MOF-MMDs, obtaining recoveries ranging from 90 to 98% for all tested analytes.

  3. [Determination of rhodamine B in spices by solid phase extraction-high performance liquid chromatography-tandem mass spectrometry].

    Science.gov (United States)

    Yin, Feng; Ding, Zhaowei; Yang, Zhijian

    2012-07-01

    Rhodamine B (RB), as an unlawful colour, is forbidden to add into foods by Chinese government. A solid phase extraction-high performance liquid chromatography-tandem mass spectrometry (SPE-HPLC-MS/MS) method for the determination of RB in spices has been developed. The sample was extracted by acetonitrile and then centrifugated, purified and enriched with a strong positive ion exchange SPE column (Bond Elut Plexa PCX SPE column) after adding 10 mL 1% trichloroacetic acid solution. The HPLC separation was performed on a Pursuit C18 column (100 mm x 2.0 mm, 3 microm) by gradient elution with 0.1% (v/v) formic acid solution and methanol as the mobile phase. The analyte was detected by electrospray ionization in positive ion mode-MS/MS in multiple reaction monitoring (MRM) mode. The good linearity (R2 > 0.99) was obtained over the range of 0.6-6 microg/L. The limit of quantification (LOQ) for RB was 1.2 microg/kg. The average recoveries were ranged from 80% to 121% at the spiked levels of 1.197, 2.992 and 5.985 microg/L, and the relative standard deviations (RSDs) were not more than 15%. The conditions of mobile phase elution gradients, extraction solvents, and SPE columns were optimized. This method is highly selective and has weak matrix effect for qualitative and quantitative analyses of RB in spices.

  4. Graphene oxide as a micro-solid-phase extraction sorbent for the enrichment of parabens from water and vinegar samples.

    Science.gov (United States)

    Wang, Lu; Zang, Xiaohuan; Wang, Chun; Wang, Zhi

    2014-07-01

    A simple hydrophilic polyamide organic membrane protected micro-solid-phase extraction method with graphene oxide as the sorbent was developed for the enrichment of some parabens from water and vinegar samples prior to gas chromatography with mass spectrometry detection. The main experimental parameters affecting the extraction efficiencies, such as the type and amount of the sorbent, extraction time, stirring rate, salt addition, sample solution pH and desorption conditions, were investigated. Under the optimized experimental conditions, the method showed a good linearity in the range of 0.1-100.0 ng/mL for water samples and 0.5-100.0 ng/mL for vinegar samples, with the correlation coefficients varying from 0.9978 to 0.9997. The limits of detection (S/N = 3) of the method were in the range of 0.005-0.010 ng/mL for water samples and 0.01-0.05 ng/mL for vinegar samples, respectively. The recoveries of the method for the analytes at spiking levels of 5.0 and 70.0 ng/mL were between 84.6 and 106.4% with the relative standard deviations varying from 4.2 to 9.5%. The results indicated that the developed method could be a practical approach for the determination of paraben residues in water and vinegar samples.

  5. Fast HPLC-MS/MS Method for Determining Penicillin Antibiotics in Infant Formulas Using Molecularly Imprinted Solid-Phase Extraction

    Directory of Open Access Journals (Sweden)

    Mónica Díaz-Bao

    2015-01-01

    Full Text Available The dairy cattle may suffer from different infections relatively often, but the inflammation of the mammary gland is very important to the farmer. These infections are frequently treated with penicillin antimicrobial drugs. However, their use may result in the presence of residues in animal products, such as milk powder and/or infant formulas, and it represents a potential risk for consumers. To monitor this, the EU has defined safe maximum residue limits (MRLs through Commission Regulation (EU number 37/2010. Although LC-MS is a trustful option for confirmation and quantification of antibiotics, the analysis of real samples with complex matrices frequently implies previous clean-up steps. In this work, precipitation polymerization has been used and different molecularly imprinted polymer (MIP sorbents were tested and optimized for the fast and simultaneous solid-phase extraction (MISPE of eight common penicillins (ampicillin, amoxicillin, oxacillin, penicillin G, penicillin V, cloxacillin, dicloxacillin, and nafcillin. The extracts were analyzed using liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS and the applicability of these polymers as sorbents for the extraction of penicillins at MRL levels in milk powder (infant formulas was proved. The limits of detection and quantification were below the legal tolerances, except for LOQ for oxacillin and cloxacillin.

  6. Simple and selective spectrophotometric determination of ruthenium after solid phase extraction with some quinoxaline dyes into microcrystalline p-dichlorobenzene

    Science.gov (United States)

    Amin, Alaa S.

    2002-07-01

    A simple selective and highly sensitive extraction method has been developed for the determination of ruthenium spectrophotometrically after extraction of its 2,3-dichloro-6-(3-carboxy-2-hydroxy-1-naphthylazo)quinoxaline (I), 2,3-dichloro-6-(2-hydroxy-3,5-dinitrophenylazo)quinoxaline (II) and 2,3-dichloro-6-(2,7-dihydroxy-naphthylazo)quinoxaline (III) complexes into microcrystalline p-dichlorobenzene. The optimization of experimental conditions for the procedure is studied. The solid p-dichlorobenzene containing the ruthenium-reagent (I-III) complexes is separated by filtration and dissolved in N, N-dimethylformamide. The absorbance is measured at λmax 622, 518 and 542 nm against reagents I, II and III, respectively, as blank. Beer's law is obeyed upto 2.5 μg ml -1 of ruthenium. The molar absorptivity, Sandell sensitivity, detection and quantification limits are calculated, when compared with those parameters without using solid phase extraction method. The interference of various ions has been studied in detail and the statistical evaluation of the experimental results is reported. The proposed methods have been successfully applied for the determination of trace amount of ruthenium in seawater, ore and metallurgy products.

  7. Determination of multi-class herbicides in soil by liquid-solid extraction coupled with headspace solid phase microextraction method

    Directory of Open Access Journals (Sweden)

    Đurović-Pejčev Rada

    2016-01-01

    Full Text Available A method is described for simultaneous determination of five herbicides (metribuzin, acetochlor, clomazone, oxyfluorfen and dimethenamid belonging to different pesticides groups in soil samples. Developed headspace solid phase microextraction method (HS-SPME in combination with liquid-solid sample preparation (LS was optimized and applied in the analysis of some agricultural samples. Optimization of microextraction conditions, such as temperature, extraction time and sodium chloride (NaCl content was perfor-med using 100 μm polydimethyl-siloxane (PDMS fiber. The extraction effi-ciencies of methanol, methanol:acetone=1:1 and methanol:acetone:hexane= =2:2:1 and the optimum number of extraction steps during the sample prepa-ration, were tested, as well. Gas chromatography-mass spectrometry (GC-MS was used for detection and quantification, obtaining relative standard deviation (RSD below 13%, and recovery values higher than 83% for multiple analyses of soil samples fortified at 30 μg kg-1 of each herbicide. Limits of detection (LOD were less than 1.2 μg kg-1 for all the studied herbicides. [Projekat Ministarstva nauke Republike Srbije, br. TR31043 i br. III43005

  8. [Determination of thiourea dioxide in lotus seed paste fillings by solid phase extraction-liquid chromatography-tandem mass spectrometry].

    Science.gov (United States)

    Wang, Hui; Zeng, Xiwen; Chang, Xiaotu; Peng, Xinkai; Xia, Lixin; Li, Yiwei

    2014-01-01

    A method of solid phase extraction-liquid chromatography-tandem mass spectrometry (SPE-LC-MS/MS) was developed to determine thiourea dioxide which was illegally added into lotus seed paste fillings. An amount of 0.05% (v/v) acetic acid was used to extract thiourea dioxide from fillings, and the BOND ELUT PLEXA column (60 mg/3 mL) was used as the SPE column to clean-up the extraction. Then, an Agilent HILIC column (100 mm x 2.1 mm, 3.5 microm) was applied to separate target compounds by using the mobile phases of 0.01 mol/L ammonium acetate (pH 3.5) and acetonitrile. Qualitative and quantitative analyses were operated by the multiple reaction monitoring (MRM) mode. The calibration curve showed a good linearity for the target compound in the detection range of 10 - 1 000 microg/L. The limit of detection (LOD) and limit of quantitation (LOQ) of this method were 8.0 microg/kg and 30.0 microg/kg, respectively. The recoveries were in the ranges of 75.3% - 80.7% with the RSDs of no more than 4.83%. This proposed method was rapid, highly specific and suitable for the confirmation and quantitative determination of thiourea dioxide in lotus seed paste fillings.

  9. In vitro biomonitoring in polar extracts of solid phase matrices reveals the presence of unknown compounds with estrogenic activity.

    Science.gov (United States)

    Legler, J; Leonards, P; Spenkelink, A; Murk, A J

    2003-01-01

    Determination of estrogenic activity has so far mainly concentrated on the assessment of compounds in surface water and effluent. This study is one of the first to biomonitor (xeno-)estrogens in sediment, suspended particulate matter and aquatic organisms. The relatively polar acetone extracts from these solid phase matrices do not contain the well-known estrogenic compounds such as hormones, alkylphenols and phthalates. An in vitro 'estrogen receptor-mediated chemical activated luciferase gene expression' (ER-CALUX) assay was applied to samples from various locations in the Netherlands. Estrogenic activity measured in polar fractions of particulate matter and sediment extracts ranged from below detection limit to up to 4.5 pmol estradiol equivalents (EEQ)/g dry weight. Estrogenic activity in freshwater river sediments was up to five times higher compared to sediments from large lakes and coastal locations. Tissue extracts EEQs were determined in bream (Abramis brama), flounder (Platichthysflesus), freshwater mussels (Dreissena polymorpha) and marine mussels (Mytilus edulis). The highest biota EEQ levels were found in the freshwater zebra mussel (30 pmol EEQ/g lipid). One sample site showed greatly elevated EEQs in sediment and biota, which correlated with effects found in the wild populations of bream. The EEQ activity of the unknown compounds in the polar fraction mostly was much higher than the calculated EEQ levels based on known estrogens in the non-polar fraction (previously published data).

  10. Hexagonal boron nitride nanosheets as adsorbents for solid-phase extraction of polychlorinated biphenyls from water samples.

    Science.gov (United States)

    Jia, Shiliang; Wang, Zhenhua; Ding, Ning; Elaine Wong, Y-L; Chen, Xiangfeng; Qiu, Guangyu; Dominic Chan, T-W

    2016-09-14

    The adsorptive potential of hexagonal boron nitride nanosheets (h-BNNSs) for solid-phase extraction (SPE) of pollutants was investigated for the first time. Seven indicators of polychlorinated biphenyls (PCBs) were selected as target analytes. The adsorption of PCBs on the surface of the h-BNNSs in water was simulated by the density functional theory and molecular dynamics. The simulation results indicated that the PCBs are adsorbed on the surface by π-π, hydrophobic, and electrostatic interactions. The PCBs were extracted with an h-BNNS-packed SPE cartridge, and eluted by dichloromethane. Gas chromatography-tandem mass spectrometry working in the multiple reaction monitor mode was used for the sample quantification. The effect of extraction parameters, including the flow rate, pH value, breakthrough volume, and the ionic strength, were investigated. Under the optimal working conditions, the developed method showed low limits of detection (0.24-0.50 ng L(-1); signal-to-noise ratio = 3:1), low limits of quantification (0.79-1.56 ng L(-1); signal-to-noise ratio = 10:1), satisfactory linearity (r > 0.99) within the concentration range of 2-1000 ng L(-1), and good precision (relative standard deviation results demonstrate that h-BNNSs have high analytical potential in the enrichment of pollutants.

  11. Solid-phase Extraction Using Hierarchical Organosilicates for Enhanced Detection of Nitroenergetic Targets

    Science.gov (United States)

    2011-01-01

    sample extracts are provided in , Age’ncy (EPA) certified ’method co~iinu~ to be the ’standard for the ESI. Materia ls characterizalion data for the MMI...organ’Osilicate ’ ’: ’ . . . ’ . ,.. -.. . materia ]. Sep-Pak, and LiChrolut EN arc also provided.’ See DO]: , evaluatmg these SlIes or poterltlal

  12. [Development of Determination Method of Fluoroquinolone Antibiotics in Sludge Based on Solid Phase Extraction and HPLC-Fluorescence Detection Analysis].

    Science.gov (United States)

    Dai, Xiao-hu; Xue, Yong-gang; Liu, Hua-jie; Dai, Ling-ling; Yan, Han; Li, Ning

    2016-04-15

    Fluoroquinolone antibiotics (FQs), as the common pharmaceuticals and personal care products (PPCPs), are widespread in the environment. FQs contained in wastewater would be ultimately enriched in sludge, posing a potential threat to the consequent sludge utilization. To optimize the analytical method applicable to the determination of FQs in sludge, the authors selected ofloxacin (OFL), norfioxacin (NOR), ciprofloxacin (CIP) and lomefloxacin (LOM) as the target FQs, and established a method which was based on cell lysis, FQs extraction with triethylamine/methanol/water solution, Solid Phase Extraction (SPE) and HPLC-Fluorescence Detection (FLD) determination. After the investigation, phosphoric acid-triethylamine was decided to be the buffer salt, and methanol was chosen as the organic mobile phase. The gradient fluorescence scanning strategy was proved to be necessary for the optimal detection as well. Furthermore, by the designed orthogonal experiments, the effects of the extraction materials, pH, and the eluents on the efficiency of SPE extraction were evaluated, by which the optimal extraction conditions were determined. As a result, FQs in liquid samples could be analyzed by utilizing HLB extraction cartridge, and the recovery rates of the four FQs were in the range of 82%-103%. As for solid samples, the recovery rates of the four FQs contained reached up to 71%-101%. Finally, the adsorptivity of the sludge from the different tanks ( anaerobic, anoxic and oxic tanks) was investigated, showing gradual decrease in the adsorption capacity, but all adsorbed over 90% of the EQs. This conclusion also confirmed that 50% removal of FQs in the domestic wastewater treatment plant was realized by sludge adsorption.

  13. Quaternary ammonium-functionalized silica sorbents for the solid-phase extraction of aromatic amines under normal phase conditions.

    Science.gov (United States)

    Vidal, Lorena; Robin, Orlane; Parshintsev, Jevgeni; Mikkola, Jyri-Pekka; Riekkola, Marja-Liisa

    2013-04-12

    Quaternary ammonium-functionalized silica materials were synthesized and applied for solid-phase extraction (SPE) of aromatic amines, which are classified as priority pollutants by US Environmental Protection Agency. Hexamethylenetetramine used for silica surface modification for the first time was employed as SPE sorbent under normal phase conditions. Hexaminium-functionalized silica demonstrated excellent extraction efficiencies for o-toluidine, 4-ethylaniline and quinoline (recoveries 101-107%), while for N,N-dimethylaniline and N-isopropylaniline recoveries were from low to moderate (14-46%). In addition, the suitability of 1-alkyl-3-(propyl-3-sulfonate) imidazolium-functionalized silica as SPE sorbent was tested under normal phase conditions. The recoveries achieved for the five aromatic amines ranged from 89 to 99%. The stability of the sorbent was evaluated during and after 150 extractions. Coefficients of variation between 4.5 and 10.2% proved a high stability of the synthesized sorbent. Elution was carried out using acetonitrile in the case of hexaminium-functionalized silica and water for 1-alkyl-3-(propyl-3-sulfonate) imidazolium-functionalized silica sorbent. After the extraction the analytes were separated and detected by liquid chromatography ultraviolet detection (LC-UV). The retention mechanism of the materials was primarily based on polar hydrogen bonding and π-π interactions. Comparison made with activated silica proved the quaternary ammonium-functionalized materials to offer different selectivity and better extraction efficiencies for aromatic amines. Finally, 1-alkyl-3-(propyl-3-sulfonate) imidazolium-functionalized silica sorbent was successfully tested for the extraction of wastewater and soil samples.

  14. Modified Bentonite with Dithizone as Nano Clay Mineral Adsorbent for Solid Phase Extraction of Silver Ions

    Directory of Open Access Journals (Sweden)

    Farid Shakerian

    2016-09-01

    Full Text Available In this work, a simple flow injection system incorporating a microcolumn of immobilized dithizone on bentonite coated with cetyltrimethylammonium bromide was combined with flame atomic absorption spectrometry (FAAS for on-line separation/preconcentration and determination of trace amounts of silver in water. Dithizone was physically immobilized on the surfactant coated bentonite particles and was used as the adsorbent in the preparation of microcolumn. Silver ions were deposited by processing a standard or sample solution of analyte in the pH range of 3–9 through the microcolumn. Injection of 250 µL of thiourea (0.4 mol L−1, pH = 5.0 served to elute the retained species to the FAAS. The capacity of the adsorbent under working conditions was found to be 7.2 mg of silver per gram of adsorbent. Processing a water sample volume of 30 mL resulted in an enrichment factor of 116. The method was successfully applied to the determination of silver in different natural waters and a certified reference material. This work is licensed under a Creative Commons Attribution 4.0 International License.

  15. Liquid chromatography-mass spectrometry platform for both small neurotransmitters and neuropeptides in blood, with automatic and robust solid phase extraction

    Science.gov (United States)

    Johnsen, Elin; Leknes, Siri; Wilson, Steven Ray; Lundanes, Elsa

    2015-03-01

    Neurons communicate via chemical signals called neurotransmitters (NTs). The numerous identified NTs can have very different physiochemical properties (solubility, charge, size etc.), so quantification of the various NT classes traditionally requires several analytical platforms/methodologies. We here report that a diverse range of NTs, e.g. peptides oxytocin and vasopressin, monoamines adrenaline and serotonin, and amino acid GABA, can be simultaneously identified/measured in small samples, using an analytical platform based on liquid chromatography and high-resolution mass spectrometry (LC-MS). The automated platform is cost-efficient as manual sample preparation steps and one-time-use equipment are kept to a minimum. Zwitter-ionic HILIC stationary phases were used for both on-line solid phase extraction (SPE) and liquid chromatography (capillary format, cLC). This approach enabled compounds from all NT classes to elute in small volumes producing sharp and symmetric signals, and allowing precise quantifications of small samples, demonstrated with whole blood (100 microliters per sample). An additional robustness-enhancing feature is automatic filtration/filter back-flushing (AFFL), allowing hundreds of samples to be analyzed without any parts needing replacement. The platform can be installed by simple modification of a conventional LC-MS system.

  16. Detailed elucidation of hydrocarbon contamination in food products by using solid-phase extraction and comprehensive gas chromatography with dual detection.

    Science.gov (United States)

    Purcaro, Giorgia; Tranchida, Peter Q; Barp, Laura; Moret, Sabrina; Conte, Lanfranco S; Mondello, Luigi

    2013-04-22

    The present work is focused on the development/optimization of a comprehensive two-dimensional gas chromatography method, with dual detection [flame ionization (FID) and mass spectrometric], for the simultaneous identification and quantification of mineral-oil contaminants in a variety of food products. The two main classes of contaminants, namely saturated and aromatic hydrocarbons, were previously fractionated on a manually-packed silver silica solid-phase extraction (SPE) cartridge. The quantitative results were compared with those obtained by performing a large volume injection, in a GC-FID system, after the same SPE process and by an on-line liquid-gas chromatography method, with very similar results observed. The presence of a series of unknown compounds, that appeared when using the off-line methods, was investigated using the mass spectrometric data, and were tentatively-identified as esterified fatty acids, most probably derived from vegetable oil based ink. Copyright © 2013 Elsevier B.V. All rights reserved.

  17. Innovative separation and preconcentration technique of coagulating homogenous dispersive micro solid phase extraction exploiting graphene oxide nanosheets

    Energy Technology Data Exchange (ETDEWEB)

    Ghazaghi, Mehri [Department of Chemistry, College of Science, Semnan University, P.O. Box: 35131-19111, Semnan (Iran, Islamic Republic of); Mousavi, Hassan Zavvar, E-mail: hzmousavi@semnan.ac.ir [Department of Chemistry, College of Science, Semnan University, P.O. Box: 35131-19111, Semnan (Iran, Islamic Republic of); Rashidi, Ali Morad [Nanotechnology Research Center, Research Institute of Petroleum Industry (RIPI), West Entrance Blvd., Olympic Village, P.O. Box: 14857-33111, Tehran (Iran, Islamic Republic of); Shirkhanloo, Hamid [Occupational and Environmental Health Research Center (OEHRC), Iranian Petroleum Industry Health Research Institute (IPIHRI), Tehran (Iran, Islamic Republic of); Rahighi, Reza [Nanotechnology Research Center, Research Institute of Petroleum Industry (RIPI), West Entrance Blvd., Olympic Village, P.O. Box: 14857-33111, Tehran (Iran, Islamic Republic of); Department of Research and Development, Sharif Ultrahigh Nanotechnologists (SUN) Company, P.O. Box: 13488-96394, Tehran (Iran, Islamic Republic of)

    2016-01-01

    A uniquely novel, fast, and facile technique is introduced for the first time in which a scant amount of graphene oxide (GO), without modification, has been utilized in dispersive mode of solid phase extraction (SPE) for an efficient yet simple separation. The proposed method of coagulating homogenous dispersive micro solid phase extraction (CHD-µSPE) is based on coagulation of homogeneous GO solution with the aid of polyetheneimine (PEI). CHD-µSPE use full adsorption capacity of GO because in this method was used GO solution obtained from synthesis process without drying step and stacking nanosheets. In optimized condition, 30 µL GO solution (7 mg mL{sup −1}), obtained in synthesis process, was injected into 1.5 mL the sample solution followed by immediate injection of 53 µL PEI solution (1 mg mL{sup −1}). After inserting PEI, GO sheets aggregate and can be readily separated by centrifugation. PEI not only cause aggregation of GO, but also form three-dimensional network of GO with easy handling in following separation steps. Lead, cadmium, and chromium were selected as model analytes and the effecting parameters including the amount of GO, concentration of PEI, sample pH, extraction time, and type of desorption solvent were investigated and optimized. The results indicate that the proposed CHD-µSPE method can be successfully applied GO in dispersive mode of SPE without effecting on good capability adsorption of GO. The novel method was applied in determination of lead, cadmium, and chromium in water, human saliva, and urine samples by electrothermal atomic absorption spectrometry. The detection limits are as low as 0.035, 0.005, and 0.012 µg L{sup −1} for Pb, Cd, and Cr respectively. The intra-day precisions (RSDs) were lower than 3.8%. CHD-µSPE method showed a good linear ranges of 0.24–15.6, 0.015–0.95 and 0.039–2.33 µg L{sup −1} for Pb, Cd and Cr respectively. Method performance was investigated by determination of mentioned

  18. Detection of urinary creatinine using gold nanoparticles after solid phase extraction.

    Science.gov (United States)

    Sittiwong, Jarinya; Unob, Fuangfa

    2015-03-05

    Label-free gold nanoparticles (AuNPs) were utilized in the detection of creatinine in human urine after a sample preparation by extraction of creatinine on sulfonic acid functionalized silica gel. With the proposed sample preparation method, the interfering effects of the urine matrix on creatinine detection by AuNPs were eliminated. Parameters affecting creatinine extraction were investigated. The aggregation of AuNPs induced by creatinine resulted in a change in the surface plasmon resonance signal with a concomitant color change that could be observed by the naked eye and quantified spectrometrically. The effect of AuNP concentration and reaction time on AuNP aggregation was investigated. The method described herein provides a determination of creatinine in a range of 15-40mgL(-1) with a detection limit of 13.7mgL(-1) and it was successfully used in the detection of creatinine in human urine samples.

  19. Micro-column solid phase extraction to determine uranium and thorium in environmental samples.

    Science.gov (United States)

    Tsai, Tsuey-Lin; Lin, Chun-Chih; Chu, Tieh-Chi

    2008-08-01

    Extraction chromatographic separation techniques based on U/TEVA and TEVA resins were utilized to separate uranium and thorium isotopes in complex matrices from environmental samples. This approach has the advantages of ease of quantitative analysis, small sample size, an absence of mixed waste solvents, complete separation of U/Th isotopes, acceptable chemical yields and good energy resolution in the alpha spectrum. The procedure for analyzing alpha-emitting isotopes of uranium and thorium in geothermal water from Peito, Taiwan, is illustrated in detail. It involves sample pre-concentration, filtration and separation by highly selective extraction chromatographic resins, followed by electroplating and alpha-spectroscopy. The analytical results show a chemical recovery exceeding 55% for U and 65% for Th, respectively, under optimized conditions. The efficient and cost-effective use of recyclable columns makes the analytical methods simple, accurate, rapid, reliable and robust.

  20. Preparation and evaluation of molecularly imprinted solid-phase micro-extraction fibers for selective extraction of phthalates in an aqueous sample.

    Science.gov (United States)

    He, Juan; Lv, Ruihe; Zhan, Haijun; Wang, Huizhi; Cheng, Jie; Lu, Kui; Wang, Fengcheng

    2010-07-26

    A novel molecularly imprinted polymer (MIP) that was applied to a solid-phase micro-extraction (SPME) device, which could be coupled directly to gas chromatograph and mass spectrometer (GC/MS), was prepared using dibutyl phthalate (DBP) as the template molecule. The characteristics and application of this fiber were investigated. Electron microscope images indicated that the MIP-coated solid-phase micro-extraction (MI-SPME) fibers were homogeneous and porous. The extraction yield of DBP with the MI-SPME fibers was higher than that of the non-imprinted polymer (NIP)-coated SPME (NI-SPME) fibers. The MI-SPME fibers had a higher selectivity to other phthalates that had similar structures as DBP. A method was developed for the determination of phthalates using MI-SPME fibers coupled with GC/MS. The extraction conditions were optimized. Detection limits for the phthalate samples were within the range of 2.17-20.84 ng L(-1). The method was applied to five kinds of phthalates dissolved in spiked aqueous samples and resulted in recoveries of up to 94.54-105.34%, respectively. Thus, the MI-SPME fibers are suitable for the extraction of trace phthalates in complicated samples.

  1. Preparation and evaluation of molecularly imprinted solid-phase micro-extraction fibers for selective extraction of phthalates in an aqueous sample

    Energy Technology Data Exchange (ETDEWEB)

    He Juan, E-mail: juanhe@haut.edu.cn [School of Chemistry and Chemical Engineering, Henan University of, Technology, LianHua Road, Zhengzhou 450051 (China); Lv Ruihe; Zhan Haijun; Wang Huizhi; Cheng Jie; Lu Kui; Wang Fengcheng [School of Chemistry and Chemical Engineering, Henan University of, Technology, LianHua Road, Zhengzhou 450051 (China)

    2010-07-26

    A novel molecularly imprinted polymer (MIP) that was applied to a solid-phase micro-extraction (SPME) device, which could be coupled directly to gas chromatograph and mass spectrometer (GC/MS), was prepared using dibutyl phthalate (DBP) as the template molecule. The characteristics and application of this fiber were investigated. Electron microscope images indicated that the MIP-coated solid-phase micro-extraction (MI-SPME) fibers were homogeneous and porous. The extraction yield of DBP with the MI-SPME fibers was higher than that of the non-imprinted polymer (NIP)-coated SPME (NI-SPME) fibers. The MI-SPME fibers had a higher selectivity to other phthalates that had similar structures as DBP. A method was developed for the determination of phthalates using MI-SPME fibers coupled with GC/MS. The extraction conditions were optimized. Detection limits for the phthalate samples were within the range of 2.17-20.84 ng L{sup -1}. The method was applied to five kinds of phthalates dissolved in spiked aqueous samples and resulted in recoveries of up to 94.54-105.34%, respectively. Thus, the MI-SPME fibers are suitable for the extraction of trace phthalates in complicated samples.

  2. Molecularly imprinted pipette-tip solid phase extraction for selective determination of fluoroquinolones in human urine using HPLC-DAD.

    Science.gov (United States)

    de Oliveira, Hanna Leijoto; da Silva Anacleto, Sara; da Silva, Anny Talita Maria; Pereira, Arnaldo César; de Souza Borges, Warley; Figueiredo, Eduardo Costa; Borges, Keyller Bastos

    2016-10-15

    A simple method using HPLC-DAD was developed for the determination of fluoroquinolones in human urine including ciprofloxacin (CIPRO), enrofloxacino (ENRO), marbofloxacino (MARBO) and norfloxacin (NOR). In addition, it was studied the extraction of fluoroquinolones in human urine samples using pipette tip-based molecularly imprinted polymers solid phase extraction (PT-MIPs-SPE). With the goal of finding the best procedure for extraction of four fluoroquinolones in human urine, several parameters that are likely to affect the efficiency of extraction during sample preparation, including the washing solvent, type and volume of eluent, amount of material, the volume of the sample, pH and the ionic strength were systematically optimized. Chromatographic separations of fluoroquinolones were hit within 10min using a Synergi(®) C18 (250×4.6mm, 4μm) column and mobile phase consisting of water (10mM of phosphoric acid, the pH adjusted at 3.29 with triethylamine) : acetonitrile (85.7: 14.3, v/v) at a flow rate of 1.5mLmin(-1). Detection was performed at 290nm. The average extraction recoveries/standard deviation relative to ENRO, CIPRO, NOR and MARBO were 96.40±5.51%, 42.47±4.81%, 41.82±7.99% and 87.49±4.70, respectively. The method was liner from 39 to 1260ngmL(-1) for each fluoroquinolone with correlation coefficient of 0.9904, 0.9910, 0.9914 and 0.9919, to ENRO, CIPRO, NOR and MARBO, respectively. The assays of within-day and between-day precision and accuracy for all analytes were studied at three concentration levels and were lower than 15%. The method was successfully employed in a preliminary cumulative urinary excretion study after administration of CIPRO to a healthy volunteer. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Head Space Solid Phase Micro-Extraction (HS - SPME of volatile organic compounds produced by Sporidiobolus salmonicolor (CBS 2636

    Directory of Open Access Journals (Sweden)

    Eunice Valduga

    2010-12-01

    Full Text Available The aim of the present study was the assessment of volatile organic compounds produced by Sporidiobolus salmonicolor (CBS 2636 using methyl and ethyl ricinoleate, ricinoleic acid and castor oil as precursors. The analysis of the volatile organic compounds was carried out using Head Space Solid Phase Micro-Extraction (HS - SPME. Factorial experimental design was used for investigating extraction conditions, verifying stirring rate (0-400 rpm, temperature (25-60 ºC, extraction time (10-30 minutes, and sample volume (2-3 mL. The identification of volatile organic compounds was carried out by Gas Chromatography with Mass Spectrum Detector (GC/MSD. The conditions that resulted in maximum extraction were: 60 ºC, 10 minutes extraction, no stirring, sample volume of 2.0 mL, and addition of saturated KCl (1:10 v/v. In the bio-production of volatile organic compounds the effect of stirring rate (120-200 rpm, temperature (23-33 ºC, pH (4.0-8.0, precursor concentration (0.02-0.1%, mannitol (0-6%, and asparagine concentration (0-0.2% was investigated. The bio-production at 28 ºC, 160 rpm, pH 6,0 and with the addition of 0.02% ricinoleic acid to the medium yielded the highest production of VOCs, identified as 1,4-butanediol, 1,2,2-trimethylciclopropilamine, beta-ionone; 2,3-butanodione, pentanal, tetradecane, 2-isononenal, 4-octen-3-one, propanoic acid, and octadecane.

  4. Study and comparison of polydopamine and its derived carbon decorated nanoparticles in the magnetic solid-phase extraction of estrogens.

    Science.gov (United States)

    Huang, Zhenzhen; Lee, Hian Kee

    2015-10-02

    Surface functionalization enabled by bioinspired polydopamine (PDA) is recognized as a convenient route for fabrication of multifunctional nanoparticles. In the present work, magnetic nanoparticles with polymer (Fe3O4@PDA) and carbon shell (Fe3O4@C) were prepared by self-oxidation of dopamine, and carbonization of the PDA coating. The performance of the two magnetic sorbents in the extraction and determination of four estrogens, estrone (E1), estradiol (E2), estriol (E3) and diethylstilbestrol (DES) from water samples in the form of magnetic solid-phase extraction was investigated. Orthogonal array design was utilized to facilitate the optimization of the proposed sample preparation approach. The highest extraction capabilities of the two sorbents were achieved under different experimental conditions. Fe3O4@PDA was shown to be superior to Fe3O4@C in the enrichment of estrogens, suggesting stronger interactions were established between the PDA coating and the target compounds. The extraction and desorption operations were enabled more conveniently by magnetic separation and the extracts were analyzed by high-performance liquid chromatography coupled with ultraviolet and fluorescence detection. The limits of detection achieved in the proposed method were in the range of 0.072-0.15ng/mL for E1 and DES, and 0.0017-0.0062ng/mL for E2 and E3. Good precision (>0.9995) was obtained with the linearity ranging from 0.2 to 100ng/mL, and from 0.01 to 5ng/mL. The method developed was assessed by analysis of the estrogens in tap water, drain water and bottled mineral water samples. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. Determination of higher carboxylic acids in snow samples using solid-phase extraction and LC/MS-TOF.

    Science.gov (United States)

    Kippenberger, Matthias; Winterhalter, Richard; Moortgat, Geert K

    2008-12-01

    The objective of this work was to develop a method to determine the concentrations of higher organic acids in snow samples. The target species are the homologous aliphatic alpha,omega-dicarboxylic acids from C(5) to C(13), pinonic acid, pinic acid and phthalic acid. A preconcentration procedure utilizing solid phase extraction was developed and optimized using solutions of authentic standards. The influences of different parameters such as flow rate during extraction and the concentration of the eluent on the efficiency of the extraction procedure were investigated. The compounds of interest were separated by HPLC and detected by a quadrupole time-of-flight mass spectrometer (qTOF-MS). The recovery rate (extraction efficiency) of the extraction procedure was found to vary between 41% for tridecanedioic acid and 102% for adipic acid. The limits of detection were determined for all compounds and were between 0.9 nmol/L (dodecanedioic acid) and 29.5 nmol/L (pinonic acid). An exception is pinic acid, for which a considerably higher detection limit of 103.9 nmol/L was calculated. Snow samples were collected in December 2006 and January 2007 at the Fee glacier (Switzerland) from locations at heights from 3056 to 3580 m asl and from different depths within the snow layer. In total, the analysis of 61 single snow samples was performed, and the following compounds could be quantified: homologous aliphatic alpha,omega-dicarboxylic acids with 5-12 carbon atoms and phthalic acid. Tridecanedioic acid, pinonic and pinic acid were identified in the samples but were not quantified due to their low concentrations. The three most abundant acids found in the molten snow samples were glutaric acid (C(5)-di; 3.90 nmol/L), adipic acid (C(6)-di; 3.35 nmol/L) and phthalic acid (Ph; 3.04 nmol/L).

  6. Separation of monosaccharides by solid-phase extraction with ionic liquid-modified microporous polymers.

    Science.gov (United States)

    Tian, Minglei; Bi, Wentao; Row, Kyung H

    2011-11-01

    Ionic liquid-modified porous polymers with large surface area and large amount of functional groups were developed and used in SPE to separate four monosaccharides. Adsorption isotherm showed that the sorbent with amino ionic liquid groups had the highest interaction with the target compounds. The mobile phase of acetonitrile/water 85:15 and 73:30 v/v can successfully separate the monosaccharides. The sorbent produced reproducible results and performed stably, demonstrating its potential applicability in the separation of extract from natural plant. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Simultaneous Determination of TetracyclinesResidues in Bovine Milk Samples by Solid Phase Extraction and HPLC-FL Method

    Directory of Open Access Journals (Sweden)

    Mehra Mesgari Abbasi

    2011-06-01

    Full Text Available Introduction:Tetracyclines (TCs are widely used in animal husbandry and their residues in milk may resultinharmful effects on human. The aim of this study was to investigate the presence of TCs residues in various bovine milk samples from local markets of Ardabil, Iran. Methods:One hundred and fourteen pasteurized, sterilized and raw milk samples were collected from markets of Ardabil. Tetracycline, Oxytetracycline and Chlortetracycline (TCs residues extraction carried out by Solid Phase Extraction method. Determination of TCs residues were performed by high performance liquid chromatography (HPLC method using Fluorescence detector.Results: The mean of total TCs residues in all samples (114 samples was 97.6 ±16.9ng/g and that of pasteurized, sterilized and raw milk samples were 87.1 ± 17.7, 112.0 ± 57.3 and 154.0 ± 66.3ng/g respectively. Twenty five point four percent of the all samples, and24.4%, 30% and 28.6% of the pasteurized, sterilized and raw milk samples, respectively had higher TCs residues than the recommended maximum levels (100ng/g. Conclusion:This study indicates the presence of tetracycline residues more than allowed amount. Regulatory authorities should ensure proper withdrawal period before milking the animals and definite supervisions are necessary on application of these drugs.

  8. Novel dummy molecularly imprinted polymers for matrix solid-phase dispersion extraction of eight fluoroquinolones from fish samples.

    Science.gov (United States)

    Sun, Xiaoli; Wang, Jincheng; Li, Yun; Yang, Jiajia; Jin, Jing; Shah, Syed Mazhar; Chen, Jiping

    2014-09-12

    A series of novel dummy molecularly imprinted polymers (DMIPs) were prepared as highly class-selective sorbents for fluoroquinolones. A non-poisonous dummy template, daidzein, was used for the first time to create specific molecular recognition sites for fluoroquinolones in the synthesized polymers. The influence of porogen polarity on dummy molecular imprinting effect was studied. The DMIP prepared using dimethylsulfoxide-acetonitrile (1:1.8, v/v) as porogen achieved the highest imprinting factors (IF) for fluoroquinolones over a range of IF 13.4-84.0. This DMIP was then used for selective extraction of eight fluoroquinolones (fleroxacin, ofloxacin, norfloxacin, pefloxacin, ciprofloxacin, lomefloxacin, enrofloxacin and gatifloxacin) from fish samples based on dummy molecularly imprinted matrix solid-phase dispersion (DMI-MSPD). The extracted fluoroquinolones were subsequently analyzed by high-performance liquid chromatography (HPLC) equipped with a fluorescence detector (FLD). The developed method had acceptable recoveries (64.4-102.7%) and precision (RSDs: 1.7-8.5%, n=5) for determination of fluoroquinolones in fish samples fortified at levels of 10 and 100ngg(-1). The limits of detection (LODs) for identification of eight fluoroquinolones ranged between 0.06 and 0.22ngg(-1). The results demonstrated great potential of the optimized method for sample preparation in routine analysis of trace fluoroquinolones in fish samples. Copyright © 2014 Elsevier B.V. All rights reserved.

  9. Screening for anabolic steroids in urine of forensic cases using fully automated solid phase extraction and LC-MS-MS.

    Science.gov (United States)

    Andersen, David W; Linnet, Kristian

    2014-01-01

    A screening method for 18 frequently measured exogenous anabolic steroids and the testosterone/epitestosterone (T/E) ratio in forensic cases has been developed and validated. The method involves a fully automated sample preparation including enzyme treatment, addition of internal standards and solid phase extraction followed by analysis by liquid chromatography-tandem mass spectrometry (LC-MS-MS) using electrospray ionization with adduct formation for two compounds. Urine samples from 580 forensic cases were analyzed to determine the T/E ratio and occurrence of exogenous anabolic steroids. Extraction recoveries ranged from 77 to 95%, matrix effects from 48 to 78%, overall process efficiencies from 40 to 54% and the lower limit of identification ranged from 2 to 40 ng/mL. In the 580 urine samples analyzed from routine forensic cases, 17 (2.9%) were found positive for one or more anabolic steroids. Only seven different steroids including testosterone were found in the material, suggesting that only a small number of common steroids are likely to occur in a forensic context. The steroids were often in high concentrations (>100 ng/mL), and a combination of steroids and/or other drugs of abuse were seen in the majority of cases. The method presented serves as a fast and automated screening procedure, proving the suitability of LC-MS-MS for analyzing anabolic steroids.

  10. Magnetic solid-phase extraction for determination of sulpiride in human urine and blood using high-performance liquid chromatography.

    Science.gov (United States)

    Zhao, Jiao; Liao, Wenlong; Yang, Yaling

    2015-12-01

    A novel and efficient sample preconcentration technique based on the Fe3O4 magnetic nanoparticles (Fe3O4 MNPs) coated with silica (SiO2) has been developed for extraction and determination of sulpiride. The functionalized MNPs showed excellent dispersibility in aqueous solution and were applied to magnetic solid-phase extraction of sulpiride from human urine and blood prior to high-performance liquid chromatography analysis. The separation, preconcentration and desorption procedure was completed in 10 min. Optimal experimental conditions, including sample pH, the amount of the MNPs, eluent type and volume, and the ultrasonication time were studied and established. The method showed good linearity for the determination of sulpiride in the concentration range of 10-1000 ng/mL in urine and blood. The recovery of the method was in the range between 91.2 and 97.5%, and the limit of detection was 2 ng/mL for sulpiride in human blood and urine. The results indicated that the present procedure is a suitable pretreatment method for biological samples.

  11. Micro-solid-phase extraction (µ-SPE) of organophosphorous pesticides from wheat followed by LC-MS/MS determination.

    Science.gov (United States)

    Della Pelle, Flavio; Di Crescenzo, Maria Chiara; Sergi, Manuel; Montesano, Camilla; Di Ottavio, Francesca; Scarpone, Rossana; Scortichini, Giampiero; Compagnone, Dario

    2016-01-01

    A rapid, selective and effective method of extraction, clean-up and concentration of organophosphorous pesticides from wheat followed by electrospray (ESI) LC-MS/MS analysis was developed. The μ-SPE (micro-solid-phase extraction) procedure resulted in good analytical performance and reduced at the same time matrix effects, analysis time and solvent consumption. Limits of detection (LODs) and quantification (LOQs) were in the range of 0.3-10 and 1-30 μg kg(-1), respectively, with good reproducibility (RSD ≤ 13.8) and recoveries between 75% and 109%. Coefficients of determination (r(2)) were greater than 0.996 for the studied pesticides. Despite the reduced sorbent bed mass of μ-SPE tips (4.2 mg), the analytical data showed that no saturation phenomena occurs in the tested range of concentration both for single compounds and mixtures. Several real samples were analysed and the concentrations of the selected pesticides were found to be below the respective maximum residue limit (MRLs).

  12. Novel multiresidue method for determination of pesticides in red wine using gas chromatography-mass spectrometry and solid phase extraction.

    Science.gov (United States)

    Pelajić, Maja; Peček, Gorana; Mutavdžić Pavlović, Dragana; Vitali Čepo, Dubravka

    2016-06-01

    A new multiresidue method was developed for determination of 25 pesticide residues in red wine by gas chromatography coupled to mass spectrometry with a single run of 23.63 min. Samples were extracted from wine with solid phase extraction using Oasis HLB. Mixture of methanol and water was used for rinsing, while acetonitrile and n-hexane were used as elution solvents. Method was validated according to SANCO/12571/2013 criteria in wide linearity range (limit of quantification - 400 μg L(-1)). Limits of quantification (LOQ) were well below 10 μg L(-1) for most pesticides and recoveries at 2×LOQ and 10×LOQ concentration levels were in range 70-120%. Precision, expressed as a relative standard deviation, was always under 14%. The method was applied to 32 red wine samples from Croatia. Pesticides were detected in 30 samples with a total of 15 pesticides found, 7 of which were at a high concentration.

  13. Application of microwave-assisted micro-solid-phase extraction for determination of parabens in human ovarian cancer tissues.

    Science.gov (United States)

    Sajid, Muhammad; Basheer, Chanbasha; Narasimhan, Kothandaraman; Choolani, Mahesh; Lee, Hian Kee

    2015-09-01

    Parabens (alkyl esters of p-hydroxybenzoic acid) are widely used as preservatives in food, cosmetics and pharmaceutical products. However, weak estrogenicity of some parabens has been reported in several studies, which provided the impetus for this work. Here, a simple and efficient analytical method for quantifying parabens in cancer tissues has been developed. This technique involves the simultaneous use of microwave-assisted solvent extraction (MASE) and micro-solid phase extraction (μ-SPE), in tandem with high performance liquid chromatography (HPLC/UV) analysis for the determination of parabens. The pollutants studied included four parabens (methyl, ethyl, propyl and butyl parabens). Optimization of the experimental parameters for MASE and μ-SPE was performed. Good relative standard deviation (%RSD) ranged from 0.09 to 2.81% and high enrichment factors (27-314) were obtained. Coefficients of determination (r(2)) up to 0.9962 were obtained across a concentration range of 5.0-200ngg(-1). The method detection limits for parabens ranged from 0.005 to 0.0244ngg(-1). The procedure was initially tested on prawn samples to demonstrate its feasibility on a complex biological matrix. Preliminary studies on human ovarian cancer (OC) tissues showed presence of parabens. Higher levels of parabens were detected in malignant ovarian tumor tissues compared to benign tumor tissue samples. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. A solid phase extraction-ion chromatography with conductivity detection procedure for determining cationic surfactants in surface water samples.

    Science.gov (United States)

    Olkowska, Ewa; Polkowska, Żaneta; Namieśnik, Jacek

    2013-11-15

    A new analytical procedure for the simultaneous determination of individual cationic surfactants (alkyl benzyl dimethyl ammonium chlorides) in surface water samples has been developed. We describe this methodology for the first time: it involves the application of solid phase extraction (SPE-for sample preparation) coupled with ion chromatography-conductivity detection (IC-CD-for the final determination). Mean recoveries of analytes between 79% and 93%, and overall method quantification limits in the range from 0.0018 to 0.038 μg/mL for surface water and CRM samples were achieved. The methodology was applied to the determination of individual alkyl benzyl quaternary ammonium compounds in environmental samples (reservoir water) and enables their presence in such types of waters to be confirmed. In addition, it is a simpler, less time-consuming, labour-intensive, avoiding use of toxic chloroform and significantly less expensive methodology than previously described approaches (liquid-liquid extraction coupled with liquid chromatography-mass spectrometry). Copyright © 2013 Elsevier B.V. All rights reserved.

  15. [Determination of dimethyl fumarate in leather and textiles by gas chromatography-tandem mass spectrometry with solid phase extraction].

    Science.gov (United States)

    Zhao, Yang; Qi, Xiaoxia

    2010-01-01

    An effective method for the determination of dimethyl fumarate (DMF) in leather and textiles by gas chromatography-tandem mass spectrometry (GC-MS/MS) was developed. Samples of leather or textiles were extracted with ethyl acetate and concentrated, DMF was separated on a VF-5 ms column and analyzed by GC-MS/MS after solid phase extraction (SPE) process. The result shows that this method is sensitive, accurate and reliable. The linear relationship was perfect and the interference with background signal was further eliminated after pretreatment, SPE and GC-MS/MS analytical conditions were optimized. The average recoveries of DMF in leather and textiles at three levels ranged from 84% to 93%, the relative standard deviations (n = 6) were lower than 7.2%, the limits of detection in the range from 0.012 to 0.039 mg/kg (S/N = 3) , the correlation coefficient was 0.999 0 over the range 0.05 - 100 mg/L. It has been applied to routine determination of DMF in leather and textiles with satisfactory results.

  16. Colourimetric solid-phase extraction coupled with fibre optic reflectance spectroscopy for determination of ascorbic acid in pharmaceutical formulations.

    Science.gov (United States)

    Filik, Hayati; Aksu, Duygu; Giray, Derya; Apak, Reşat

    2012-06-01

    A redox colourimetric solid-phase extraction (C-SPE) procedure for the determination of ascorbic acid (AA) in pharmaceutical formulations was proposed. Iron (III)-2,2'-dipyridyl (Fe(III)-Bpy) reagent solution was used as a colouring reagent for AA and the immobilization of the redox product onto Amberlite XAD-16 resin was achieved. The analyte in the sample reacted with a solid sorbent loaded with the colourimetric reagent (Fe(III)-Bpy) and then quantified directly on the sorbent surface by using a fibre optic reflectance spectrometer (FORS). The amount of AA was reflectometrically determined in a few seconds with a total sample workup and readout time of ∼10 min using only 10-ml sample volumes. The limit of detection (LOD) and quantification (LOQ) values were 0.18 and 0.6 mg L(-1), respectively, and the linear dynamic range for AA extended up to 8.8 mg L(-1). The C-SPE for different extractions (n = 5) gave a relative standard deviation (RSD) of 2.9% at 5.28 mg L(-1) AA level.

  17. [Simultaneous determination of captan and folpet pesticide residues in apples by solid-phase extraction and high performance liquid chromatography].

    Science.gov (United States)

    Wang, Shuju; Yu, Yanbin; Tan, Peigong; Miao, Zaijing; Wei, Yishan

    2007-03-01

    A method for the simultaneous determination of captan and folpet pesticide residues in apples was developed by solid-phase extraction and high performance liquid chromatography. The sample was extracted with acetonitrile and cleaned-up by a mixture of homemade sorbent and silica gel with hexane-dichloromethane-acetonitrile (50:49: 1, v/v) as the eluent. The cleaned effects by using Florisil column, amino column, the mixed sorbent were compared, and the effect of the mixed sorbent was the best. The optimal analytical conditions were follow as: an methanol-acetonitrile-water (50: 5:45, v/v) containing 0. 1 mmol/L acetic-acetate buffer (pH 3. 80) as the mobile phase, detection at 210 nm. The method had a good linear relationship in the range of 0. 40 - 8. 00 mg/kg for captan and folpet (r > 0. 999 9). The detection limits of captan and folpet were 0. 27 mg/kg and 0. 20 mg/kg, respectively. The relative standard deviations (RSDs) of retention time were no more than 0. 60%. The average recoveries of captan and folpet from the apples spiked at three levels ranged from 69. 3% - 106% and 101% - 108%, with RSD of 3. 7% - 4. 7% and 1. 3% - 5. 4%, respectively.

  18. Determination of phthalates released from paper packaging materials by solid-phase extraction-high-performance liquid chromatography.

    Science.gov (United States)

    Gao, Xin; Yang, Bofeng; Tang, Zhixu; Luo, Xin; Wang, Fengmei; Xu, Hui; Cai, Xue

    2014-01-01

    A solid phase extraction (SPE) high-performance liquid chromatography (HPLC) method was developed for the simultaneous determination of 10 phthalic acid esters (dimethyl phthalate, diethyl phthalate, dipropyl phthalate, benzylbutyl phthalate, diisobutyl phthalate, dicyclohexyl phthalate, diamyl phthalate, di-n-hexyl phthalate, di-n-octyl phthalate and di-2-ethylhexyl phthalate) released from food paper packaging materials. The use of distilled water, 3% acetic acid (w/v), 10% ethanol (v/v) and 95% ethanol (v/v) instead of the different types of food simulated the migration of 10 phthalic acid esters from food paper packaging materials; the phthalic acid esters in four food simulants were enriched and purified by a C18 SPE column and nitrogen blowing, and quantified by HPLC with a diode array detector. The chromatographic conditions and extraction conditions were optimized and all 10 of the phthalate acid esters had a maximum absorbance at 224 nm. The method showed limitations of detection in the range of 6.0-23.8 ng/mL the correlation coefficients were greater than 0.9999 in all cases, recovery values ranged between 71.27 and 106.97% at spiking levels of 30, 60 and 90 ng/mL and relative standard deviation values ranged from 0.86 to 8.00%. The method was considered to be simple, fast and reliable for a study on the migration of these 10 phthalic acid esters from food paper packaging materials into food.

  19. Determination of Antioxidant Flavonoids in Sudanese Honey Samples by Solid Phase Extraction and High Performance Liquid Chromatography

    Directory of Open Access Journals (Sweden)

    Suzan Zein Alabdeen Makawi

    2009-01-01

    Full Text Available Flavonoids were extracted by solid phase extraction (SPE from seven floral honey samples of different botanical origin from different regions of Sudan. The flavonoids were determined by high performance liquid chromatography (HPLC technique using photo diode array detector (PDA. An isocratic and gradient systems for the resolution, identification and quantification of five flavonoids, namely; quercetin, kaempferol, apigenin, hesperetin and isorhamnetin, were developed. Although the isocratic system resolved the five compounds, however it suffered from interference by the complex mixture of honey samples. The gradient system resolved three of five flavonoids, namely, quercetin, kaempferol, and isorhamnetin, without interference by the complex honey matrix. Two flavonoids, apigenin and hesperetin, were observed to elute at close retention times, which lead to their interference with each other when injected in a mixture; however, absorption wavelength selection was found indicative of the presence or absence of either compound. The quantification of these flavonoids was done through the calibration curves of their standards. The obtained results were compared with reported results.

  20. Selective solid-phase extraction using molecularly imprinted polymer as a sorbent for the analysis of fenarimol in food samples.

    Science.gov (United States)

    Khan, Shagufta; Bhatia, Tejasvi; Trivedi, Purushottam; Satyanarayana, G N V; Mandrah, Kapil; Saxena, Prem Narayan; Mudiam, Mohana Krishna Reddy; Roy, Somendu Kumar

    2016-05-15

    In the present communication, a non-covalent fenarimol-imprinted polymer was synthesized by precipitation polymerization technique using methacrylic acid (MAA) as a functional monomer, ethylene glycol dimethacrylate (EGDMA) as a cross-linker, and azobisisobutyronitrile (AIBN) as an initiator in different porogenic solvent. Binding study of molecularly imprinted and non-imprinted polymer (MIP and NIP) showed that MIP possesses a higher affinity towards this analyte compared to NIP. The binding affinity of MIP was calculated by static and kinetic adsorption study. Further, a MIP based cartridge was designed to use in extraction process, necessary for specific determination and quantification of the fungicide in food matrices. Under the optimum conditions, developed method was found to be linear (R(2)=0.9999-0.9994). Limit of detection (LOD) and limit of quantitation (LOQ) in samples were 0.03-0.06 and 0.12-0.21 μg mL(-1), respectively. The rate of recovery of fenarimol was 91.16-99.52% on MIPs. The validated method of molecularly imprinted solid-phase extraction (MISPE) cartridge was successfully applied to the food matrices and compared with commercial sorbent (RP18 and Oasis HLB). However we feel, this method has promising applications in the routine analysis of food samples in industry.

  1. Graphene oxide-based microspheres for the dispersive solid-phase extraction of non-steroidal estrogens from water samples.

    Science.gov (United States)

    Wen, Yingying; Niu, Zongliang; Ma, Yanling; Ma, Jiping; Chen, Lingxin

    2014-11-14

    A modified Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) method based on the dispersive solid-phase extraction (dSPE) combined with high performance liquid chromatography (HPLC) was developed for the determination of non-steroidal estrogens in water samples. In this study, graphene oxide-based silica microspheres (SiO2@GO) were used as dSPE material for the preconcentration of analytes. HPLC was used for the separation and detection. This was the first time that the synthesized SiO2@GO microspheres were used as stationary phases for the off-line preconcentration of the non-steroidal estrogens in dSPE. dSPE parameters, such as sample pH, volume and type of eluent were optimized. Application of the developed method to analyze spiked lake, reservoir and tap water samples resulted in good recoveries values ranging from 70 to 106% with relative standard deviation values lower than 7.0% in all cases. Limits of detection were in the range of 0.2-6.1 μg/L. The combined data obtained in this study recommended that the proposed method is very fast, simple, repeatable and accurate for the detection of non-steroidal estrogens. Furthermore, the SiO2@GO microspheres application could potentially be expanded to extract and pre-concentrate other compounds in various matrices.

  2. Rapid method for determination of glyphosate in groundwater using high performance liquid chromatography and solid-phase extraction after derivatization

    Directory of Open Access Journals (Sweden)

    Valdir Eduardo Olivo

    2015-04-01

    Full Text Available The intensive use of pesticides in agriculture has prompted researchers to develop new methods for identifying these pollutants in water. This study sought to validate a high performance liquid chromatography (HPLC method to determine the concentration of the pesticide glyphosate in groundwater samples by using solid-phase extraction (SPE filters after derivatization with chloroformate 9-fluorenylmethoxycarbonyl (FMOC-Cl. For the HPLC method, we evaluated the following main validation parameters: linearity, specificity, precision, accuracy, robustness, and limits of detection and quantification. After validation of the method, we determined the concentration of glyphosate in samples from thirteen deep, tubular wells distributed in urban and rural areas in Chapecó, SC, Brazil. The solvent used in the extraction of excess FMOC-Cl was dichloromethane and subsequently filtration was performed on C18 SPE, and injected into the chromatograph column in amino polymer with fluorescence detection. The analytical curve made in ultrapure water was linear, with a correlation coefficient of 0.99. The limits of detection and quantification were 0.24 and 0.07 µg L-1, respectively. Recovery tests in natural waters ranged from 90.37 to 101.70%. Glyphosate was detected in 5 of the thirteen wells evaluated. The highest concentration of glyphosate (6.80 µg L-1 was detected in a countryside well, near the municipal water supply. Despite the low levels of glyphosate detected in our study, any amount present in groundwater samples is worrisome, as these molecules have low ground mobility.

  3. Dummy molecularly imprinted mesoporous silica prepared by hybrid imprinting method for solid-phase extraction of bisphenol A.

    Science.gov (United States)

    Yu, Dan; Hu, Xiaolei; Wei, Shoutai; Wang, Qiang; He, Chiyang; Liu, Shaorong

    2015-05-29

    A novel hybrid dummy imprinting strategy was developed to prepare a mesoporous silica for the solid-phase extraction (SPE) of bisphenol A (BPA). A new covalent template-monomer complex (BPAF-Si) was first synthesized with 2,2-bis(4-hydroxyphenyl)hexafluoropropane (BPAF) as the template. The imprinted silica was obtained through the gelation of BPAF-Si with tetraethoxysilane and the subsequent removal of template by thermal cleavage, and then it was characterized by FT-IR spectroscopy, scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption-desorption isotherms. Results showed that the new silica had micron-level particle size and ordered mesoporous structure. The static binding test verified that the imprinted silica had much higher recognition ability for BPA than the non-imprinted silica. The imprinted silica also showed high extraction efficiencies and high enrichment factor for SPE of BPA. Using the imprinted silica, a SPE-HPLC-UV method was developed and successfully applied for detecting BPA in BPA-spiked tap water and lake water samples with a recovery of 99-105%, a RSD of 2.7-5.0% and a limit of detection (S/N=3) of 0.3ng/mL. The new imprinted silica avoided the interference of the residual template molecules and reduced the non-specific binding sites, and therefore it can be utilized as a good sorbent for SPE of BPA in environmental water samples.

  4. Graphene oxide bound silica for solid-phase extraction of 14 polycyclic aromatic hydrocarbons in mainstream cigarette smoke.

    Science.gov (United States)

    Shi, Rui; Yan, Lihong; Xu, Tongguang; Liu, Dongye; Zhu, Yongfa; Zhou, Jun

    2015-01-02

    Polycyclic aromatic hydrocarbons (PAHs) were considered as a source of carcinogenicity in mainstream cigarette smoke (MSS). Accurate quantification of these components was necessary for assessing public health risk. In our study, a solid-phase extraction (SPE) method using graphene oxide (GO) bound silica as adsorbent for purification of 14 PAHs in MSS was developed. During SPE process, large matrices interferences of MSS were adsorbed on SPE column. The result of FTIR spectra demonstrated that these matrices interferences were adsorbed on GO mainly through OH and CO groups. The concentrations of PAHs in MSS extract were determined by gas chromatography-mass spectrometry (GC-MS). The limit of detection (LOD) and limit of quantification (LOQ) of the developed method for 14 PAHs ranged from 0.05 to 0.36 ng/cig and 0.17 to 1.19 ng/cig, respectively. The accuracy of the measurement of 14 PAHs was from 73 to 116%. The relative standard deviations of intra- and inter-day analysis were less than 7.8% and 13.9%, respectively. Moreover, the developed method was successfully applied for analysis of real cigarette containing 1R5F reference cigarette and 12 top-selling commercial cigarettes in China.

  5. Surface molecularly imprinted silica for selective solid-phase extraction of biochanin A, daidzein and genistein from urine samples.

    Science.gov (United States)

    Chrzanowska, Anna M; Poliwoda, Anna; Wieczorek, Piotr P

    2015-05-01

    Selective molecularly imprinted silica polymer (SiO2MIP) for extraction of biochanin A, daidzein and genistein was synthesized using the surface molecular imprinting technique with the silica gel as a support. Biochanin A (BCA) was used as a template, 3-aminopropyltriethoxysilane (APTES) as a functional monomer, and tetraethoxysilicane (TEOS) as a cross-linker. Non-imprinted polymer with the sol-gel process (SiO2NIP) was also prepared for comparison. The synthesized polymers were characterized by Fourier transform infrared spectrometry (FTIR), scanning electron microscopy (SEM) and a standard Brunauer-Emett-Teller (BET) and Barret-Joyner-Halenda (BJH) analysis. The obtained results indicated the structural differences between imprinted and non-imprinted polymers. Finally, the SiO2MIP and SiO2NIP were adopted as the adsorbents of solid phase extraction for isolation and preconcentration of biochanin A and its structural analogues-daidzein and genistein from aqueous and urine samples. The performance analysis revealed that SiO2MIP displayed better affinity to the three investigated isoflavones compared with SiO2NIP. The recoveries of spiked samples for studied analytes ranged from 65.7% to 102.6% for molecularly imprinted silica polymer and 8.9-16.0% for non-imprinted sorbents.

  6. A New Solid Phase Extraction for the Determination of Anthocyanins in Grapes

    Directory of Open Access Journals (Sweden)

    Marta Ferreiro-González

    2014-12-01

    Full Text Available A method for the concentration and cleaning of red grape extracts prior to the determination of anthocyanins by UPLC-DAD has been developed. This method is of special interest in the determination of phenolic maturity as it allows the analysis of the anthocyanins present in grapes. Several different SPE cartridges were assessed, including both C-18- and vinylbenzene-based cartridges. C-18-based cartridges presented a very low retention for the glucosylated anthocyanidins while vinylbenzene-based cartridges showed excellent retention for these compounds. The optimized method involves the initial conditioning of the cartridge using 10 mL of methanol and 10 mL of water, followed by loading of up to 100 mL of red grape extract. Ten mL of water was used in the washing step and anthocyanins were subsequently eluted using 1.5 mL of acidified methanol at pH 2. This method simplifies the determination of individual anthocyanins as, on the one hand, it cleans the sample of interference and, on the other hand, it increases the concentration to up to 25:1.5. The developed method has been validated with a range of different grapes and it has also been tested as a means of determining the different anthocyanins in grapes with different levels of maturity.

  7. Unusual seeding mechanism for enhanced performance in solid-phase magnetic extraction of Rare Earth Elements

    Science.gov (United States)

    Polido Legaria, Elizabeth; Rocha, Joao; Tai, Cheuk-Wai; Kessler, Vadim G.; Seisenbaeva, Gulaim A.

    2017-03-01

    Due to the increasing demand of Rare Earth Elements (REE or RE), new and more efficient techniques for their extraction are necessary, suitable for both mining and recycling processes. Current techniques such as solvent extraction or solid adsorbents entail drawbacks such as using big volumes of harmful solvents or limited capacity. Hybrid nanoadsorbents based on SiO2 and highly stable γ-Fe2O3-SiO2 nanoparticles, proved recently to be very attractive for adsorption of REE, yet not being the absolute key to solve the problem. In the present work, we introduce a highly appealing new approach in which the nanoparticles, rather than behaving as adsorbent materials, perform as inducers of crystallization for the REE in the form of hydroxides, allowing their facile and practically total removal from solution. This induced crystallization is achieved by tuning the pH, offering an uptake efficiency more than 20 times higher than previously reported (up to 900 mg RE3+/g vs. 40 mg RE3+/g). The obtained phases were characterized by SEM-EDS, TEM, STEM and EFTEM and 13C and 29Si solid state NMR. Magnetic studies showed that the materials possessed enough magnetic properties to be easily removed by a magnet, opening ways for an efficient and industrially applicable separation technique.

  8. Determination of the Antibiotic Oxytetracycline in Commercial Milk by Solid-Phase Extraction: A High-Performance Liquid Chromatography (HPLC) Experiment for Quantitative Instrumental Analysis

    Science.gov (United States)

    Mei-Ratliff, Yuan

    2012-01-01

    Trace levels of oxytetracylcine spiked into commercial milk samples are extracted, cleaned up, and preconcentrated using a C[subscript 18] solid-phase extraction column. The extract is then analyzed by a high-performance liquid chromatography (HPLC) instrument equipped with a UV detector and a C[subscript 18] column (150 mm x 4.6 mm x 3.5 [mu]m).…

  9. Development of Solid-Phase Extraction Using Molecularly Imprinted Polymer for the Analysis of Organophosphorus Pesticides-(Chlorpyrifos) in Aqueous Solution

    OpenAIRE

    Binsalom, A.; Chianella, I.; Campbell, K.; Zourob, M.

    2016-01-01

    A new and selective sorbent for molecularly imprinted solid-phase extraction (MISPE) was prepared to extract chlorpyrifos (CPF) residue from solutions. The extracted analyte was analyzed by high performance liquid chromotography (HPLC) coupled with photodiode array detection. To synthesize the molecularly imprinted polymers, four different pyrogens (acetonitrile, toluene, dichloromethane and chloroform) were initially studied. CPF was used as the template molecule, methacrylic acid as the fun...

  10. Determination of the Antibiotic Oxytetracycline in Commercial Milk by Solid-Phase Extraction: A High-Performance Liquid Chromatography (HPLC) Experiment for Quantitative Instrumental Analysis

    Science.gov (United States)

    Mei-Ratliff, Yuan

    2012-01-01

    Trace levels of oxytetracylcine spiked into commercial milk samples are extracted, cleaned up, and preconcentrated using a C[subscript 18] solid-phase extraction column. The extract is then analyzed by a high-performance liquid chromatography (HPLC) instrument equipped with a UV detector and a C[subscript 18] column (150 mm x 4.6 mm x 3.5 [mu]m).…

  11. Solid-phase extraction and liquid chromatographic quantitation of quinfamide in biological samples.

    Science.gov (United States)

    Morales, J M; Jung, C H; Alarcón, A; Barreda, A

    2000-09-15

    This paper describes a high-performance liquid chromatographic method for the assay of quinfamide and its main metabolite, 1-(dichloroacetyl)-1,2,3,4,-tetrahydro-6-quinolinol, in plasma, urine and feces. It requires 1 ml of biological fluid, an extraction using Sep-Pack cartridges and acetonitrile for drug elution. Analysis was performed on a CN column (5 microm) using water-acetonitrile-methanol (40:50:10) as a mobile phase at 269 nm. Results showed that the assay was linear in the range between 0.08 and 2.0 microg/ml. The limit of quantitation was 0.08 microg/ml. Maximum assay coefficient of variation was 14%. Recovery obtained in plasma, urine and feces ranged from 82% to 98%.

  12. Solid phase extraction for multiresidue analysis of anabolic steroids and related substances from calf urine using C18 and alumina columns

    NARCIS (Netherlands)

    Koole, A; Franke, JP; de Zeeuw, RA

    1999-01-01

    A solid phase extraction method for anabolic steroids and related substances in calf urine is reported, that is suitable as a screening method for illegal growth promoters. Two types of sorbent were used: a reversed phase C18 material and a polar alumina material. After overnight enzymatic deconjuga

  13. Solid Phase Extraction Technique Based on Electrospun Nanofibrous%基于电纺纳米纤维的固相萃取技术

    Institute of Scientific and Technical Information of China (English)

    李晓晴; 刘静静; 祁菲菲; 杨碧漪; 田甜; 许茜

    2016-01-01

    Nanofibers have been considered as a potential kind of sorbent for solid phase extraction, accordingly nanofiber-based solid phase extraction ( Nanofibers based solid phase extraction, NFs-SPE ) becomes a popular research point of sample pretreatment technique. This article reviewed in and abroad research status of practical application in food, environmental and biological sample preparation based on nanofibers mat, and proposed that there was a dual “structure”-“activity” relationship between target adsorption efficiency and the two structures ( nanometer morphological structure and molecular structure ) of nanofibers, which would be the key breakthrough to explore adsorption mechanism.%纳米纤维极具优越固相萃取介质的潜质,基于纳米纤维的固相萃取法( Nanofibers based solid phase extraction, NFs-SPE)已成为新兴的样品预处理技术。本文在评述NFs-SPE在食品、环境样品、生物样品等实际样品检测应用的相关研究基础上,提出纳米纤维的分子结构和形态结构与目标物吸附效能之间存在着“结构”-“效应”关系,这将是明确纳米纤维高效吸附目标物的机理的关键突破口。

  14. Utilizing thin-film solid-phase extraction to assess the effect of organic carbon amendments on the bioavailability of DDT and dieldrin to earthworms

    Science.gov (United States)

    Improved approaches are needed to rapidly and accurately assess the bioavailability of persistent, hydrophobic organic compounds in soils at contaminated sites. The performance of a thin-film solid-phase extraction (TF-SPE) assay using vials coated with ethylene vinyl acetate polymer was compared to...

  15. Use of semi-permeable membrane devices and solid-phase extraction for the wide-range screening of microcontaminants in surface water by GC-AED/MS

    NARCIS (Netherlands)

    Stee, van L.L.P.; Leonards, P.E.G.; Loon, van W.M.G.M.; Hendriks, A.J.; Maas, J.L.; Struijs, J.; Brinkman, U.A.T.

    2002-01-01

    An automated GC-MS-based screening method was developed for over 400 industrial, agrochemical and household chemicals. Extracted ion chromatograms were used and the method was aimed at creating a minimum number of false positives. The compound polarity range usually associated with solid-phase extra

  16. Use of semi-permeable membrane devices and solid-phase extraction for the wide-range screening of microcontaminants in surface water by GC-AED/MS

    NARCIS (Netherlands)

    Stee, van L.L.P.; Leonards, P.E.G.; Loon, van W.M.G.M.; Hendriks, A.J.; Maas, J.L.; Struijs, J.; Brinkman, U.A.T.

    2002-01-01

    An automated GC-MS-based screening method was developed for over 400 industrial, agrochemical and household chemicals. Extracted ion chromatograms were used and the method was aimed at creating a minimum number of false positives. The compound polarity range usually associated with solid-phase extra

  17. Ion suppression in the determination of clenbuterol in urine by solid-phase extraction atmospheric pressure chemical ionisation ion-trap mass spectrometry

    NARCIS (Netherlands)

    van Hout, M.W.J.; Niederlander, H.A G; de Zeeuw, R.A.; de Jong, G.J.

    2003-01-01

    Ion suppression effects were observed during the determination of clenbuterol in urine with solid-phase extraction/multiple-stage ion-trap mass spectrometry (SPE/MS3), despite the use of atmospheric pressure chemical ionisation. During SPE, a polymeric stationary phase (polydivinylbenzene) was appli

  18. Separation and determination of citrinin in corn using HPLC fluorescence detection assisted by molecularly imprinted solid phase extraction clean-up

    Science.gov (United States)

    A liquid chromatography based method to detect citrinin in corn was developed using molecularly imprinted solid phase extraction (MISPE) sample clean-up. Molecularly imprinted polymers were synthesized using 1,4-dihydroxy-2-naphthoic acid as the template and an amine functional monomer. Density func...

  19. METHOD 544. DETERMINATION OF MICROCYSTINS AND NODULARIN IN DRINKING WATER BY SOLID PHASE EXTRACTION AND LIQUID CHROMATOGRAPHY/TANDEM MASS SPECTROMETRY (LC/MS/MS)

    Science.gov (United States)

    Method 544 is an accurate and precise analytical method to determine six microcystins (including MC-LR) and nodularin in drinking water using solid phase extraction and liquid chromatography tandem mass spectrometry (SPE-LC/MS/MS). The advantage of this SPE-LC/MS/MS is its sensi...

  20. Magnetic graphene oxide modified with choline chloride-based deep eutectic solvent for the solid-phase extraction of protein

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Yanhua; Wang, Yuzhi, E-mail: wyzss@hnu.edu.cn; Pan, Qi; Wang, Ying; Ding, Xueqin; Xu, Kaijia; Li, Na; Wen, Qian

    2015-06-02

    Highlights: • A strategy for extraction of protein based on DES-coated magnetic graphene oxide. • The deep eutectic solvents were based on choline chloride. • Bovine serum albumin was used as the analyte. • The material prepared works for the acidic but not the basic or the neutral proteins. - Abstract: Four kinds of green deep eutectic solvents (DESs) based on choline chloride (ChCl) have been synthesized and coated on the surface of magnetic graphene oxide (Fe{sub 3}O{sub 4}@GO) to form Fe{sub 3}O{sub 4}@GO-DES for the magnetic solid-phase extraction of protein. X-ray diffraction (XRD), vibrating sample magnetometer (VSM), Fourier transform infrared spectrometry (FTIR), field emission scanning electron microscopy (FESEM) and thermal gravimetric analysis (TGA) were employed to characterize Fe{sub 3}O{sub 4}@GO-DES, and the results indicated the successful preparation of Fe{sub 3}O{sub 4}@GO-DES. The UV–vis spectrophotometer was used to measure the concentration of protein after extraction. Single factor experiments proved that the extraction amount was influenced by the types of DESs, solution temperature, solution ionic strength, extraction time, protein concentration and the amount of Fe{sub 3}O{sub 4}@GO-DES. Comparison of Fe{sub 3}O{sub 4}@GO and Fe{sub 3}O{sub 4}@GO-DES was carried out by extracting bovine serum albumin, ovalbumin, bovine hemoglobin and lysozyme. The experimental results showed that the proposed Fe{sub 3}O{sub 4}@GO-DES performs better than Fe{sub 3}O{sub 4}@GO in the extraction of acidic protein. Desorption of protein was carried out by eluting the solid extractant with 0.005 mol L{sup −1} Na{sub 2}HPO{sub 4} contained 1 mol L{sup −1} NaCl. The obtained elution efficiency was about 90.9%. Attributed to the convenient magnetic separation, the solid extractant could be easily recycled.

  1. Lab-on-a-chip mRNA purification and reverse transcription via a solid-phase gene extraction technique.

    Science.gov (United States)

    Nestorova, Gergana G; Hasenstein, Karl; Nguyen, Nam; DeCoster, Mark A; Crews, Niel D

    2017-03-14

    Extraction and purification of high quality RNA is a crucial initial step required for a variety of genomic assays. We report a solid phase gene extraction (SPGE) method for automated extraction, purification and reverse transcription of mRNA in a microfluidic device. This is performed using a 130 μm diameter stainless steel needle that is amino-linked to dT(15) oligonucleotides for selective hybridization of mRNA. By inserting this probe into the biological sample for only 30 seconds, mRNA is captured with high selectivity and a yield greater than 10 pg per mm of probe length. The probe is then inserted into a lab-on-a-chip device, where the bound poly-adenylated RNA is thermally released and immediately reverse transcribed for subsequent PCR amplification. The insertion of the probe into the microfluidic device is straightforward: the microchannel is formed with an elastomer (PDMS) that, when punctured, will seal around the probe. The specificity and RNA loading capacity of the probes were evaluated using conventional qPCR. This procedure was successfully used to extract, purify, and transcribe mRNA from rat glioblastoma cell spheroids in less than seven minutes. Analysis of the product confirmed that the SPGE technique selectively captures and inherently purifies high-quality mRNA directly from biological material with no need for additional pre-processing steps. Integrating this elegant sample preparation method into a complete lab-on-a-chip system will substantially enhance the speed and automation of mRNA assays for research and clinical diagnostics.

  2. Simultaneous analysis of some club drugs in whole blood using solid phase extraction and gas chromatography-mass spectrometry.

    Science.gov (United States)

    Castro, André L; Tarelho, Sónia; Silvestre, Armando; Teixeira, Helena M

    2012-02-01

    The use of psychoactive substances to improve social relations and increase body energy, in Rave Culture, has raised many legal and health public concerns, both for illicit trade and consumption. Therefore, forensic toxicology plays an important role in this area, mainly linked to the detection and quantitation of these substances, both in vivo and in post-mortem samples. In fact, at the moment, forensic sciences have been under public authorities' scrutiny and critical look, due to the increasing attention of the media and public opinion, always applying for the use of scientific knowledge to help solving forensic cases. However, forensic toxicology results are only reliable to solve legal cases if all the analytical methodologies used are appropriately validated. In this work, a methodology for the extraction and analysis of 7-aminoflunitrazepam, buprenorphine, flunitrazepam, ketamine, methadone, phencyclidine (PCP) and d-propoxyphene was developed for whole blood samples, with solid phase extraction (SPE), using OASIS(®) MCX SPE columns, and gas chromatography coupled to mass spectrometry. The procedure presented here proved to be reliable, specific, selective and sensitive, with good LODs and LOQs and good precision.The adoption of a SPE procedure with an automatic SPE extraction device, allowed an increased level of automation in sample treatment, being contemporarily less time-consuming, increasing productiveness, and allowing good recovery and appropriate selectivity being, also, simple and reproducible. The simultaneous detection and quantitation of all compounds by the same extraction and detection methodology is crucial and has a great potential for forensic toxicology and clinical analysis.

  3. Determination of fungicides in wine by mixed-mode solid phase extraction and liquid chromatography coupled to tandem mass spectrometry.

    Science.gov (United States)

    Carpinteiro, I; Ramil, M; Rodríguez, I; Cela, R

    2010-11-26

    A novel procedure for the determination of nine selected fungicides (metalaxyl-M, azoxystrobin, myclobutanil, flusilazole, penconazole, tebuconazole, propiconazole, diniconazole and difenoconazole) in wine samples is presented. Sample enrichment and purification is simultaneously performed using mixed-mode, anion exchange and reversed-phase, OASIS MAX solid-phase extraction (SPE) cartridges. Analytes were determined by liquid chromatography coupled to tandem mass spectrometry using atmospheric pressure electrospray ionization (LC-ESI-MS/MS). Parameters affecting the chromatographic determination and the extraction-purification processes were thoroughly investigated. Under optimized conditions, 10 mL of wine were firstly diluted 1:1 with ultrapure water and then passed through the mixed-mode SPE cartridge at a flow of ca. 5 mLmin(-1). After a washing step with 5 mL of an aqueous NH(4)OH solution (5%, w:v), analytes were recovered with just 1 mL of methanol and injected in the LC-MS/MS system without any additional purification. The selective extraction process avoided significant changes in the ionization efficiency for red and white wine extracts in comparison with pure standards in methanol. Performance of the method was good in terms of precision (RSDs72%, determined against pure standards in methanol) reporting method LOQs in the range of 0.01-0.79 ngmL(-1) for target compounds, which are far below the EU maxima residue levels (MRLs) for fungicides in vinification grapes and wine. Several commercial wines from different geographic areas in Spain were analyzed. In most samples, metalaxyl-M and azoxystrobin were found at concentrations up to several ngmL(-1). Copyright © 2010 Elsevier B.V. All rights reserved.

  4. Solid-phase extraction of fluoroquinolones from aqueous samples using a water-compatible stochiometrically imprinted polymer.

    Science.gov (United States)

    Benito-Peña, Elena; Urraca, Javier L; Sellergren, Börje; Moreno-Bondi, María Cruz

    2008-10-24

    A novel and simple method for the selective cleanup and preconcentration of fluoroquinolone antibiotics in environmental water samples has been developed using molecularly imprinted polymer solid-phase extraction (MISPE). The molecularly imprinted polymer (MIP) has been prepared using enrofloxacin (ENR) as the template and a stoichiometric quantity of urea-based functional monomer to target the single oxyanionic moieties in the template molecule. The selectivity of the material for enrofloxacin, and structurally related and non-related compounds, has been evaluated using it as stationary phase in liquid chromatography. The novel polymer and the corresponding non-imprinted material (NIP) have been characterised using nitrogen adsorption-desorption isotherms and scanning electron microscopy. Various parameters affecting the extraction efficiency of the materials in the MISPE procedure were evaluated in order to achieve optimal preconcentration and to reduce non-specific interactions. The optimized MISPE/HPLC with fluorescence detection (FLD) method allows direct extraction of the antibiotics from the aqueous samples followed by a selective washing with acetonitrile/water (0.1M 2-[4-(2-hydroxyethyl)-1-piperazinyl]ethanesulfonic acid (HEPES) buffer, pH 7.5) (10/90, v/v) and elution with 2% trifluoracetic acid in methanol. Good recoveries and precision, ranging between 66 and 100% (RSD: 2-12%, n=3) for danofloxacin, enrofloxacin, oxolinic acid and flumequine, and moderate recoveries (15-40%, RSD 4-9%, n=3) for norfloxacin, ciprofloxacin, lomefloxacin and sarafloxacin, have been obtained for river water samples fortified with 0.50, 0.75 and 1.0microgL(-1) of all the antibiotics. The method detection limits ranged between 0.01 and 0.30microgL(-1) for all the antibiotics tested, when 100mL water samples were processed. The results demonstrate the applicability of the optimized method for the selective extraction of fluoroquinolones in environmental water samples at the ng

  5. Preparation of magnetite-loaded silica microspheres for solid-phase extraction of genomic DNA from soy-based foodstuffs.

    Science.gov (United States)

    Shi, Ruobing; Wang, Yucong; Hu, Yunli; Chen, Lei; Wan, Qian-Hong

    2009-09-04

    Solid-phase extraction has been widely employed for the preparation of DNA templates for polymerase chain reaction (PCR)-based analytical methods. Among the variety of adsorbents studied, magnetically responsive silica particles are particularly attractive due to their potential to simplify, expedite, and automate the extraction process. Here we report a facile method for the preparation of such magnetic particles, which entails impregnation of porous silica microspheres with iron salts, followed by calcination and reduction treatments. The samples were characterized using powder X-ray diffractometry (XRD), scanning electron microscopy (SEM), nitrogen adsorption/desorption isotherms, and vibrating sample magnetometry (VSM). XRD data show that magnetite nanocrystals of about 27.2 nm are produced within the pore channels of the silica support after reduction. SEM images show that the as-synthesized particles exhibit spherical shape and uniform particle size of about 3 microm as determined by the silica support. Nitrogen sorption data confirm that the magnetite-loaded silica particles possess typical mesopore structure with BET surface area of about 183 m(2)/g. VSM data show that the particles display paramagnetic behavior with saturation magnetization of 11.37 emu/g. The magnetic silica microspheres coated with silica shells were tested as adsorbents for rapid extraction of genomic DNA from soybean-derived products. The purified DNA templates were amplified by PCR for screening of genetically modified organisms (GMOs). The preliminary results confirm that the DNA extraction protocols using magnetite-loaded silica microspheres are capable of producing DNA templates which are inhibitor-free and ready for downstream analysis.

  6. Graphene-encapsulated silica as matrix solid-phase dispersion extraction sorbents for the analysis of poly-methoxylated flavonoids in the leaves of Murraya panaculata (L.) Jack.

    Science.gov (United States)

    Sun, Ting; Li, Xuwen; Yang, Jie; Li, Lanjie; Jin, Yongri; Shi, Xiaolei

    2015-06-01

    In this study, graphene-encapsulated silica was synthesized by a hydrothermal reduction strategy. The presence of silica in graphene was identified by Fourier-transform infrared spectrometry, X-ray diffraction and scanning electron microscopy. The graphene-encapsulated silica subsequently was used as adsorbent for matrix solid-phase dispersion extraction of poly-methoxylated flavonoids from the dried leaves of Murraya panaculata (L.) Jack. Compared with the other adsorbents (graphene, silica gel, C18 silica, neutral alumina, diatomaceous earth) and without any adsorbents, better results were obtained. Then a method for analysis of poly-methoxylated flavonoids was established by coupling matrix solid-phase dispersion extraction with ultra high performance liquid chromatography and UV detection. Compared with reflux extraction and ultrasonic extraction, the proposed method is quicker, more efficient and more environmental protection. Less than 10 min is needed from extraction to detection.

  7. Employing Solid Phase Microextraction as Extraction Tool for Pesticide Residues in Traditional Medicinal Plants

    Science.gov (United States)

    Gondo, Thamani T.; Mmualefe, Lesego C.; Okatch, Harriet

    2016-01-01

    HS-SPME was optimised using blank plant sample for analysis of organochlorine pesticides (OCPs) of varying polarities in selected medicinal plants obtained from northern part of Botswana, where OCPs such as DDT and endosulfan have been historically applied to control disease carrying vectors (mosquitos and tsetse fly). The optimised SPME parameters were used to isolate analytes from root samples of five medicinal plants obtained from Maun and Kasane, Botswana. The final analytes determination was done with a gas chromatograph equipped with GC-ECD and analyte was confirmed using electron ionisation mass spectrometer (GC-MS). Dieldrin was the only pesticide detected and confirmed with MS in the Terminalia sericea sample obtained from Kasane. The method was validated and the analyte recoveries ranged from 69.58 ± 7.20 to 113 ± 15.44%, with RSDs ranging from 1.19 to 17.97%. The method indicated good linearity (R2 > 0.9900) in the range of 2 to 100 ng g−1. The method also proved to be sensitive with low limits of detection (LODs) ranging from 0.48 ± 0.16 to 1.50 ± 0.50 ng g−1. It can be concluded that SPME was successfully utilized as a sampling and extraction tool for pesticides of diverse polarities in root samples of medicinal plants. PMID:27725893

  8. Employing Solid Phase Microextraction as Extraction Tool for Pesticide Residues in Traditional Medicinal Plants

    Directory of Open Access Journals (Sweden)

    Thamani T. Gondo

    2016-01-01

    Full Text Available HS-SPME was optimised using blank plant sample for analysis of organochlorine pesticides (OCPs of varying polarities in selected medicinal plants obtained from northern part of Botswana, where OCPs such as DDT and endosulfan have been historically applied to control disease carrying vectors (mosquitos and tsetse fly. The optimised SPME parameters were used to isolate analytes from root samples of five medicinal plants obtained from Maun and Kasane, Botswana. The final analytes determination was done with a gas chromatograph equipped with GC-ECD and analyte was confirmed using electron ionisation mass spectrometer (GC-MS. Dieldrin was the only pesticide detected and confirmed with MS in the Terminalia sericea sample obtained from Kasane. The method was validated and the analyte recoveries ranged from 69.58±7.20 to 113±15.44%, with RSDs ranging from 1.19 to 17.97%. The method indicated good linearity (R2>0.9900 in the range of 2 to 100 ng g−1. The method also proved to be sensitive with low limits of detection (LODs ranging from 0.48±0.16 to 1.50±0.50 ng g−1. It can be concluded that SPME was successfully utilized as a sampling and extraction tool for pesticides of diverse polarities in root samples of medicinal plants.

  9. Nanostructured conducting molecularly imprinted polymer for selective extraction of salicylate from urine and serum samples by electrochemically controlled solid-phase micro-extraction.

    Science.gov (United States)

    Ameli, Akram; Alizadeh, Naader

    2011-11-30

    Overoxidized polypyrrole (OPPy) films templated with salicylate (SA) have been utilized as conducting molecular imprinted polymers (CMIPs) for potential-induced selective solid-phase micro-extraction processes. Various important fabrication factors for controlling the performance of the OPPy films have been investigated using fluorescence spectrometry. Several key parameters such as applied potential for uptake, release, pH of uptake and release solution were varied to achieve the optimum micro-extraction procedure. The film template with SA exhibited excellent selectivity over some interference. The calibration graphs were linear in the ranges of 5×10(-8) to 5×10(-4) and 1.2×10(-6) to 5×10(-4)mol mL(-1) and the detection limit was 4×10(-8) mol L(-1). The OPPy film as the solid-phase micro-extraction absorbent has been applied for the selective clean-up and quantification of trace amounts of SA from physiological samples. The results of scanning electron microscopy (SEM) have confirmed the nano-structure morphologies of the films.

  10. Semi-automated solid-phase extraction method for studying the biodegradation of ochratoxin A by human intestinal microbiota.

    Science.gov (United States)

    Camel, Valérie; Ouethrani, Minale; Coudray, Cindy; Philippe, Catherine; Rabot, Sylvie

    2012-04-15

    A simple and rapid semi-automated solid-phase (SPE) extraction method has been developed for the analysis of ochratoxin A in aqueous matrices related to biodegradation experiments (namely digestive contents and faecal excreta), with a view of using this method to follow OTA biodegradation by human intestinal microbiota. Influence of extraction parameters that could affect semi-automated SPE efficiency was studied, using C18-silica as the sorbent and water as the simplest matrix, being further applied to the matrices of interest. Conditions finally retained were as follows: 5-mL aqueous samples (pH 3) containing an organic modifier (20% ACN) were applied on 100-mg cartridges. After drying (9 mL of air), the cartridge was rinsed with 5-mL H(2)O/ACN (80:20, v/v), before eluting the compounds with 3 × 1 mL of MeOH/THF (10:90, v/v). Acceptable recoveries and limits of quantification could be obtained considering the complexity of the investigated matrices and the low volumes sampled; this method was also suitable for the analysis of ochratoxin B in faecal extracts. Applicability of the method is illustrated by preliminary results of ochratoxin A biodegradation studies by human intestinal microbiota under simple in vitro conditions. Interestingly, partial degradation of ochratoxin A was observed, with efficiencies ranging from 14% to 47% after 72 h incubation. In addition, three phase I metabolites could be identified using high resolution mass spectrometry, namely ochratoxin α, open ochratoxin A and ochratoxin B.

  11. Tea bag filter paper as a novel protective membrane for micro-solid phase extraction of butachlor in aqueous samples.

    Science.gov (United States)

    Pelden, Tshering; Thammaknet, Chongdee; Thavarungkul, Panote; Kanatharana, Proespichaya

    2014-01-01

    An innovative, cost-effective, simple, and environmental friendly tea bag filter paper protected micro-solid phase extraction (μ-SPE) technique was developed for the first time with the aim to miniaturize and minimize the use of organic solvents for the extraction and determination of butachlor in aqueous samples. The μ-SPE device was produced by packing 3.0 mg of an easily synthesized new sorbent, hydroxyl-functionalized polypyrrole (OH-PPY), inside a small tea bag filter paper sachet (1.0 cm × 0.5 cm) that served as a protective envelope. Both the extraction and desorption procedures were facilitated by sonication. Due to the high porosity and the fast water absorption of the tea bag filter paper, the analyte could easily diffuse through and enhance the interaction with the sorbent. Under the optimized conditions for the GC-ECD and the μ-SPE, the limit of detection (S/N ≥ 3) was 2.0 μg L(-1) while the limit of quantitation (S/N ≥ 10) was 10.0 μg L(-1). The recoveries of the butachlor spiked at 0.050, 0.10, and 0.50 μg mL(-1) ranged from 77.9 ± 3.0 to 112.5 ± 2.9%. The proposed method was successfully applied for the determination of butachlor in water samples from paddy cultivation sites. The levels found were from non-detectable to 24.71 ± 0.37 μg L(-1).

  12. Vortex-homogenized matrix solid-phase dispersion for the extraction of short chain chlorinated paraffins from indoor dust samples.

    Science.gov (United States)

    Chen, Yu-Hsuan; Chang, Chia-Yu; Ding, Wang-Hsien

    2016-11-11

    A simple and effective method for determining short chain chlorinated paraffins (SCCPs) in indoor dust is presented. The method employed a modified vortex-homogenized matrix solid-phase dispersion (VH-MSPD) prior to its detection by gas chromatography - electron-capture negative-ion mass spectrometry (GC-ECNI-MS) operating in the selected-ion-monitoring (SIM) mode. Under the best extraction conditions, 0.1-g of dust sample was dispersed with 0.1-g of silica gel by using vortex (2min) instead of using a mortar and pestle (3min). After that step, the blend was transferred to a glass column containing 3-g acidic silica gel, 2-g basic silica gel, and 2-g of deactivated silica gel, used as clean-up co-sorbents. Then, target analytes were eluted with 5mL of n-hexane/dichloromethane (2:1, v/v) mixture. The extract was evaporated to dryness under a gentle stream of nitrogen. The residue was then re-dissolved in n-hexane (10μL), and subjected to GC-ECNI-MS analysis. The limits of quantitation (LOQs) ranged from 0.06 to 0.25μg/g for each SCCP congener. Precision was less than 7% for both intra- and inter-day analysis. Trueness was above 89%, which was calculated by mean extraction recovery. The VH-MSPD combined with GC-ECNI-MS was successfully applied to quantitatively detect SCCPs from various indoor dust samples, and the concentrations ranged from 1.2 to 31.2μg/g. Copyright © 2016 Elsevier B.V. All rights reserved.

  13. Application of dissolvable layered double hydroxides as sorbent in dispersive solid-phase extraction and extraction by co-precipitation for the determination of aromatic acid anions.

    Science.gov (United States)

    Tang, Sheng; Lee, Hian Kee

    2013-08-06

    Three types of magnesium-aluminum layered double hydroxides were synthesized and employed as solid-phase extraction (SPE) sorbents to extract several aromatic acids (protocatechuic acid, mandelic acid, phthalic acid, benzoic acid, and salicylic acid) from aqueous samples. An interesting feature of these sorbents is that they dissolve when the pH of the solution is lower than 4. Thus, the analyte elution step, as needed in conventional sorbent-based extraction, was obviated by dissolving the sorbent in acid after extraction and separation from the sample solution. The extract was then directly injected into a high-performance liquid chromatography-ultraviolet detection system for analysis. In the key adsorption process, both dispersive SPE and co-precipitation extraction with the sorbents were conducted and experimental parameters such as pH, temperature, and extraction time were optimized. The results showed that both extraction methods provided low limits of detection (0.03-1.47 μg/L) and good linearity (r(2) > 0.9903). The optimized extraction conditions were applied to human urine and sports drink samples. This new and interesting extraction approach was demonstrated to be a fast and efficient procedure for the extraction of organic anions from aqueous samples.

  14. [Simultaneous determination of nine pharmaceuticals personal care products in waters by solid phase extraction-gas chromatography-mass spectrometry].

    Science.gov (United States)

    Jia, Yanyan; Tan, Jianhua; Xu, Chen; Tang, Jiajun; Wang, Yingli; Xie, Qilai

    2014-03-01

    An analytical method has been developed and validated for the simultaneous determination of nine pharmaceuticals and personal care products (PPCPs) in water samples, including salicylic acid, naproxen, ibuprofen, paracetamol, clofibric acid, triclosan, diclofenac, ketoprofen, bisphenol A. The qualification and quantification of the target compounds were performed by gas chromatography-mass spectrometry in selected ion monitoring mode (GC-MS-SIM). The water samples were concentrated and purified through Oasis HLB cartridges after the pH value of the water was adjusted to 3, then derivatized with trimethyl sulfonium hydroxide (TMSH) at room temperature, and determined by GC-MS-SIM using 2,4,5-fenoprop as internal standard. The conditions for sample pretreatment (e. g. solid phase extraction and derivatization) were studied. Under the optimized conditions, the recoveries were ranged from 50.7% to 115.4% with the relative standard deviations lower than 10%. The limits of detection were in the range of 0.03-0.30 microg/L and the limits of quantification were in the range of 0.15-1.50 microg/L. The method has been successfully applied to monitor the occurrence of the PPCPs residues in agricultural irrigation water in Dongguan, Guangdong Province. The four compounds were detected at maximum mass concentration range of 0.176-0.998 microg/L. It proved that this analytical method is sensitive, reliable and acceptable.

  15. Synthetic approaches to parabens molecularly imprinted polymers and their applications to the solid-phase extraction of river water samples.

    Science.gov (United States)

    Beltran, A; Marcé, R M; Cormack, P A G; Borrull, F

    2010-09-10

    In this paper we describe the synthesis, characterisation and use of two distinct molecularly imprinted polymers (MIPs) prepared using esters of p-hydroxybenzoic acid (parabens) as templates: one MIP was synthesised by precipitation polymerisation using a semi-covalent molecularly imprinting strategy with methyl paraben as the template/target (MIP 1); the second MIP was prepared in monolithic form through a conventional non-covalent molecular imprinting strategy, with butyl paraben as the template (MIP 2). MIP 1 recognized methyl paraben, showed cross-selectivity for other parabens analytes used in the study and higher affinity towards these compounds than did a non-imprinted control polymer. Similarly, MIP 2 demonstrated higher affinity towards paraben analytes than a non-imprinted control polymer. For the analysis of environmental water samples, a solid-phase extraction (SPE) protocol was developed using MIP 2 as sorbent, and results were compared to a SPE using a commercial sorbent (Oasis HLB). With MIP 2 as sorbent and butyl paraben as target, when percolating 500 mL of river water spiked at 1 μg L(-1) through the SPE cartridge, and using 1 mL of isopropanol as cleaning solvent, a higher recovery of butyl 4-hydroxybenzoate (butyl paraben) and a cleaner chromatogram where achievable when using the MIP compared to the commercial sorbent.

  16. Coupling solid-phase extraction and enzyme-linked immunosorbent assay for ultratrace determination of herbicides in pristine water

    Science.gov (United States)

    Aga, D.S.; Thurman, E.M.

    1993-01-01

    Solid-phase extraction (SPE) and enzyme-linked immunosorbent assay (ELISA) were coupled for automated trace analysis of pristine water samples containing 2-chloro-4-ethylamino-6-isopropylamine-s-triazine (atrazine) and 2-chloro-2???,6???-diethyl-N-(methoxymethyl)acetanilide (alachlor). The isolation of the two herbicides on a C18-resin involved the selection of an elution solvent that both removes interfering substances and is compatible with ELISA. Ethyl acetate was selected as the elution solvent followed by a solvent exchange with methanol/water (20/80, % v/v). The SPE-ELISA method has a detection limit of 5.0 ng/L (5 ppt), >90% recovery, and a relative standard deviation of ??10%. The performance of a microtiter plate-based ELISA and a magnetic particle-based ELISA coupled to SPE was also evaluated. Although the sensitivity of the two ELISA methods was comparable, the precision using magnetic particles was improved considerably (??10% versus ??20%) because of the faster reaction kinetics provided by the magnetic particles. Finally, SPE-ELISA and isotope dilution gas chromatography/ mass spectrometry correlated well (correlation coefficient of 0.96) for lake-water samples. The SPE-ELISA method is simple and may have broader applications for the inexpensive automated analysis of other contaminants in water at trace levels.

  17. [Study on solid phase extraction and spectrophotometric determination of uranium in water with 2-(2-quinolylazo)-5-dimthylaminophenol].

    Science.gov (United States)

    Wang, Liang; Yuan, Zhuo-Bin; Hu, Qiu-Fen; Yang, Guang-Yu; Yin, Jia-Yuan

    2005-05-01

    A new chromogenic reagent 2-(2-quinolylazo)-5-Dimthylaminophenol (QADMAP) was synthesized, and its structure was verified by elemental analysis, infrared spectrum, 1H nuclear magnetic resonance spectrum, mass spectrumand UV-spectrum. The color reaction of QADMAP with uranium was studied. In the presence of pH 7.8 buffer solution, when fluorin ion and TritonX-100 medium exist, QADMAP can react with uranium and fluorin to form a stable 1 : 1 : 1 stable complex [F- :QADMAP : U(VI)]. The molar absorptivity is 1.05 x 10(5) L x mol(-1) x cm(-1) at 590 nm. Beer's law is obeyed in range of 0-20 microg/10 mL. The uranium in samples can be enriched and separated by solid phase extraction with TBP resin cartridge. This method is applied to the determination of uranium in water sample. The relative standard deviations are 2.2%-3.6%, and the recoveries are 94%-105%.

  18. Preparation and adsorption performance of 5-azacytosine-functionalized hydrothermal carbon for selective solid-phase extraction of uranium.

    Science.gov (United States)

    Song, Qiang; Ma, Lijian; Liu, Jun; Bai, Chiyao; Geng, Junxia; Wang, Hang; Li, Bo; Wang, Liyue; Li, Shoujian

    2012-11-15

    A new solid-phase extraction adsorbent was prepared by employing a two-step "grafting from" approach to anchor a multidentate N-donor ligand, 5-azacytosine onto hydrothermal carbon (HTC) microspheres for highly selective separation of U(VI) from multi-ion system. Fourier-transform infrared and X-ray photoelectron spectroscopies were used to analyze the chemical structure and properties of resultant HTC-based materials. The adsorption behavior of U(VI) onto the adsorbent was investigated as functions of pH, contact time, ionic strength, temperature, and initial U(VI) concentration using batch adsorption experiments. The U(VI) adsorption was of pH dependent. The adsorption achieved equilibrium within 30 min and followed a pseudo-second-order equation. The adsorption amount of U(VI) increased with raising the temperature from 283.15 to 333.15K. Remarkably, high ionic strength up to 5.0 mol L(-1) NaNO(3) had only slight effect on the adsorption. The maximum U(VI) adsorption capacity reached 408.36 mg g(-1) at 333.15K and pH 4.5. Results from batch experiments in a simulated nuclear industrial effluent, containing 13 co-existing cations including uranyl ion, showed a high adsorption capacity and selectivity of the adsorbent for uranium (0.63 mmol U g(-1), accounting for about 67% of the total adsorption amount).

  19. Application of magnetic graphitic carbon nitride nanocomposites for the solid-phase extraction of phthalate esters in water samples.

    Science.gov (United States)

    Wang, Man; Yang, Xiaodi; Bi, Wentao

    2015-02-01

    Magnetic graphitic carbon nitride nanocomposites were successfully prepared in situ and used to develop a highly sensitive magnetic solid-phase extraction method for the preconcentration of phthalate esters such as di-n-butyl phthalate, butyl phthalate, dihexyl phthalate, and di-(2-ethyl hexyl) phthalate from water. The adsorption and desorption of the phthalate esters on magnetic graphitic carbon nitride nanocomposites were investigated and the parameters affecting the partition of the phthalate esters, such as adsorption, desorption, recovery, were assessed. Under the optimized conditions, the proposed method showed excellent sensitivity with limits of detection (S/N = 3) in the range of 0.05-0.1 μg/L and precision in the range of 1.1-2.6% (n = 5). This method was successfully applied to the analysis of real water samples, and good spiked recoveries over the range of 79.4-99.4% were obtained. This research provides a possibility to apply this nanocomposite for adsorption, preconcentration, or even removal of various carbon-based ring or hydrophobic pollutants. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Determination of eight illegal drugs in human urine by combination of magnetic solid-phase extraction with capillary zone electrophoresis.

    Science.gov (United States)

    Chen, Ming-Luan; Suo, Li-Li; Gao, Qiang; Feng, Yu-Qi

    2011-08-01

    Using magnetite/silica/poly(methacrylic acid-co-ethylene glycol dimethacrylate) (Fe(3)O(4)/SiO(2)/poly(MAA-co-EDMA)) magnetic microspheres, a rapid and high-throughput magnetic solid-phase extraction coupled with capillary zone electrophoresis (MSPE-CZE) method was developed for the determination of illegal drugs (ketamine, amphetamines, opiates, and metabolites). The MSPE of target analytes could be completed within 2 min, and the eight target analytes could be baseline separated within 15 min by CZE with 30 mM phosphate buffer solution (PBS, pH 2.0) containing 15% v/v ACN as background electrolyte. Furthermore, hydrodynamic injection with field-amplified sample stacking (FASS) was employed to enhance the sensitivity of this MSPE-CZE method. Under such optimal conditions, the limits of detection for the eight target analytes ranged from 0.015 to 0.105 μg/mL. The application feasibility of MSPE-CZE in illegal drugs monitoring was demonstrated by analyzing urine samples, and the recoveries of target drugs for the spiked sample ranging from 85.4 to 110.1%. The method reproducibility was tested by evaluating the intra- and interday precisions, and relative standard deviations of <10.3 and 12.4%, respectively, were obtained. To increase throughput of the analysis, a home-made MSPE array that has potential application to the treatment of 96 samples simultaneously was used.

  1. Preparation and characterization of porous DVB copolymers and their applicability for adsorption (solid-phase extraction) of phenol compounds

    Science.gov (United States)

    Sobiesiak, Magdalena; Podkoscielna, Beata

    2010-12-01

    Using DVB, three new porous copolymers in the form of microspheres were prepared, characterized and used as adsorbents for phenol and its chlorinated derivatives. As the monomers: 4,4'-bis(maleimidodiphenyl)methane (BM), 2,3-bis(2-hydroxy-3-methylacryloyloxy-propoxy)naphthalene (2,3-NAF) and 2,3-epoxypropyl methacrylate (GLY) were used. All the studied materials were synthesized under the same conditions by means of suspension copolymerization. The DVB copolymers were characterized by elemental analysis, FTIR spectroscopy, TG and DSC analyses and N 2 sorption. The off-line solid-phase extraction method (SPE) was used to estimate sorption properties of the copolymers. The results show that the newly obtained materials are mesoporous but their shape of pores and chemical structures are different. BM-DVB and GLY-DVB are characterized by slit-shaped pores and wide pore size distribution. 2,3-NAF-DVB also possesses slit pores but distribution of pore size is narrower. Of those studied BM-DVB is the most interesting material. It has good sorption properties and heat resistance.

  2. Method development for fingerprinting of biodiesel blends by solid-phase extraction and gas chromatography-mass spectrometry.

    Science.gov (United States)

    Yang, Zeyu; Hollebone, Bruce P; Wang, Zhendi; Yang, Chun; Landriault, Mike

    2011-11-01

    A method based on the combination of solid-phase extraction (SPE) with gas chromatography-mass spectrometry (GC/MS) for detailed chemical fingerprinting of biodiesel/petrodiesel blends was developed in the present study. Forensic identification, commonly referred to as chemical fingerprinting, is based on the relative distributions of individual aliphatic hydrocarbons, aromatic hydrocarbons, fatty acid alkyl esters, and free sterols. Fractionation of fuel samples is optimized for the separation of fatty acid esters and free sterols from petroleum hydrocarbons into four fractions: aliphatic, aromatic, fatty acid ester, and polar components. The final recoveries of aliphatic and aromatic hydrocarbons were determined to be in the range of 65-103%, 73-105% for FAMEs, and 78-103% for free sterols in the polar fraction. Excellent separation with negligible crossover of components with different polarities between fractions was observed. Quantitative analysis of blend levels and individual chemical distribution were achieved. The method has great potential for the identification of biodiesel in diesel fuel blends and could form the basis of a method for characterization of biodiesel-contaminated environmental samples. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. High-throughput online solid-phase extraction tandem mass spectrometry: Is it right for your clinical laboratory?

    Science.gov (United States)

    Jannetto, Paul J; Langman, Loralie J

    2016-09-01

    With increasing patient volumes and growing demands for rapid turnaround on many clinical tests, there is a demand for high-throughput technologies. High-Throughput Online Solid-Phase Extraction Tandem Mass Spectrometry is an example of one technology that can achieve these desired results and the RapidFire 365 Mass Spectrometry system from Agilent Technologies is one vendor's solution. The key advantage of the RapidFire system is its speed of analysis and throughput. While the Agilent RapidFire system cannot be utilized for every clinical analyte, it does work well for several classes of medications including immunosuppressants, anticonvulsants and antineoplastic agents where dosage adjustments are made to maximize efficacy and minimize toxicity once results are available. In the end, high throughput tandem mass spectrometry has numerous benefits and limitations which must be weighed for each clinical analyte to determine if it's the right solution for your lab. This article will specifically discuss the Agilent RapidFire system.

  4. Facile synthesis of magnetic molecularly imprinted polymers and its application in magnetic solid phase extraction for fluoroquinolones in milk samples.

    Science.gov (United States)

    Zheng, Hao-Bo; Mo, Jie-Zhen; Zhang, Yu; Gao, Qiang; Ding, Jun; Yu, Qiong-Wei; Feng, Yu-Qi

    2014-02-14

    In this work, we proposed a simple co-mixing method to fabricate magnetic molecularly imprinted polymers (magnetic MIPs). MIPs were commercial products while magnetic nanoparticles (MNPs) were prepared by chemical oxidation and solvothermal methods. When MNPs and MIPs (with mass ratio 1:1) were co-mixed and vortexed evenly in methanol, they could assemble into magnetic composites spontaneously and thus be magnetically separable. To testify the feasibility of the magnetic composites in sample preparation, the resultant magnetic MIPs were applied as sorbents for magnetic solid-phase extraction (MSPE) of fluoroquinolones (FQs) in milk samples. Under optimized conditions, a rapid, convenient, and efficient method for the determination of three FQs in milk samples was established by magnetic MIPs based MSPE coupling with high performance liquid chromatography with ultraviolet detector (HPLC-UV). The limits of detection (LODs) for three FQs were found to be 1.8-3.2ng/g. The intra- and inter-day relative standard deviations (RSDs) were less than 9.5% and 12.5%, respectively. The recoveries of FQs for two spiked milk samples were in the range from 94.0% to 124.4% with the RSDs less than 11.6%.

  5. Solid phase extractive preconcentration of uranium(VI) using quinoline-8-ol anchored chloromethylated polymeric resin beads.

    Science.gov (United States)

    Praveen, R S; Metilda, P; Daniel, S; Rao, T Prasada

    2005-10-31

    A new chelating polymeric sorbent has been developed using Merrifield chloromethylated resin anchored with quinoline-8-ol (HQ). The modified polymeric resin was characterized by FT-IR spectroscopy and elemental analysis. The HQ anchored resin showed superior binding affinity for U(VI) over Th(IV) and La(III). The influence of various physicochemical parameters on the recovery of U(VI) were optimized by both static and dynamic methods. The phase exchange kinetic studies performed for U(VI) revealed that XAD-16. The developed HQ anchored polymeric resin is highly selective as none of the extraneous species were found to have any deleterious effect. Solid phase extraction (SPE) studies performed using HQ anchored polymeric resin offered enrichment factor of 100 and the lowest concentration below which recoveries become non-quantitative is 5mugl(-1). The accuracy of the developed SPE method in conjunction with Arsenazo III procedure was tested by analyzing marine sediment (MESS-3) and soil (IAEA-Soil 7) reference materials. Furthermore, the above procedure has been successfully employed for the analysis of real soil and sediment samples.

  6. Boiling Point Distribution of Hydrocarbon Types in Diesel Using Solid-Phase Extraction Followed by GC/FID-EIMS

    Institute of Scientific and Technical Information of China (English)

    Li Chengwei; Tian Songbai; Liu Zelong; Zhu Xinyi

    2008-01-01

    In this paper, a method was established to determine the boiling point distribution of hydro-carbon types in diesel. The diesel sample was separated into the saturate and aromatic fractions by means of solid-phase extraction (SPE), and each fraction was analyzed by GC/FID-EIMS. According to the relationship between boiling point and retention time of n-paraffins in the chromatogram, the percent-ages of saturates and aromatics at each temperature interval were calculated. According to the average mass spectra of the saturate and aromatic fractions at each temperature interval, the hydrocarbon types of the sample were identified through summation of characteristic mass fragments. Using this method,the changes in composition of diesel during hydrotreating process were studied. The results showed that hydrogenation of aromatics is the main reaction during the hydrotreating process. The more rings the aromatics have, the easier the hydrogenation reactions would take place. The aromatics were converted into cycloparaffins via the hydrogenation and saturation process, leading to an increase in low boiling point fractions in the hydrotreated oil.

  7. Speciation of mercury in water and fish samples by HPLC-ICP-MS after magnetic solid phase extraction.

    Science.gov (United States)

    Zhu, Siqi; Chen, Beibei; He, Man; Huang, Tong; Hu, Bin

    2017-08-15

    In this paper, Fe3O4@SiO2@γ-mercaptopropyltrimethoxysilane (γ-MPTS) magnetic nanoparticles was prepared and a new method of magnetic solid phase extraction (MSPE)-high performance liquid chromatography (HPLC)-inductively coupled plasma mass spectrometry (ICP-MS) was developed for the speciation of mercury including inorganic mercury (Hg(2+)), methylmercury (MeHg(+)) and phenylmercury (PhHg(+)) in environmental water, wastewater, tap water and fish samples. A rapid separation of three target mercury species was achieved in 8min by employing relatively high ratio of methanol in HPLC mobile phase. Various parameters affecting Fe3O4@SiO2@γ-MPTS-based MSPE of target mercury species have been investigated. Under the optimized conditions, the limits of detection for Hg(2+), MeHg(+) and PhHg(+) were in the range of 0.49-0.74ngL(-1). The intra- and inter-day relative standard deviations (n=5) were less than 9.0% and 12%, respectively. The developed MSPE-HPLC-ICP-MS method was validated by the speciation of mercury in the Certified Reference Material of DORM-2 dogfish as well as real-world samples including environmental water, wastewater, tap water and fish samples, and it has the advantages of simple operation, rapid separation, high sensitivity, high enrichment factor and is suitable for the analysis of mercury species in samples with complex matrix. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. Chromatographic evaluation of polymers imprinted with analogs of chloramphenicol and application to selective solid-phase extraction.

    Science.gov (United States)

    Schirmer, Christina; Meisel, Hans

    2009-08-01

    To obtain a highly selective material for the antibiotic chloramphenicol, which has several harmful side effects in humans, different molecularly imprinted polymers (MIPs) were prepared. In order to avoid a major traditional drawback associated with MIPs of residual template bleeding, molecules that are structurally related to chloramphenicol were used as templates for polymer synthesis. Chromatographic evaluation indicated that the employed template imparted a significant influence on the recognition properties of the corresponding polymer. A strong retention of chloramphenicol under nonpolar elution conditions (k = 68.03, IF = 17.72) and under aqueous elution conditions (k = 92.44, IF = 1.35) was achieved. After chromatographic evaluation, the MIP was utilized as the recognition sorbent in a solid-phase extraction to determine chloramphenicol using either an organic or aqueous washing solvent. Recoveries of nearly 100% from the chloramphenicol standard solution and nearly 90% from honey samples spiked with chloramphenicol were attained. Furthermore, the applicability of the MIP for sample cleanup was demonstrated.

  9. Phosphopeptide enrichment: Development of magnetic solid phase extraction method based on polydopamine coating and Ti(4+)-IMAC.

    Science.gov (United States)

    Piovesana, Susy; Capriotti, Anna Laura; Cavaliere, Chiara; Ferraris, Francesca; Samperi, Roberto; Ventura, Salvatore; Laganà, Aldo

    2016-02-25

    Protein post translational modifications currently represent one of the main challenges with proteomic analysis, due to the important biological role they play within cells. Protein phosphorylation is one of the most important, with several approaches developed for phosphopeptides enrichment and analysis, essential for comprehensive phosphoproteomic analysis. However, the development of new materials for phosphopeptides enrichment may overcome previous drawbacks and improve enrichment of such peptides. In this regard, new magnetic stationary phases based on polydopamine coating and Ti(4+) immobilization exploit the potential of IMAC enrichment and couple it with the versatility of magnetic solid phase extraction. In this work the use of such stationary phase was extended from the MALDI proof of concept stage with the development of an optimized method for phosphopeptides enrichment compatible with typical shotgun proteomics experimental workflows. Different loading and elution buffers were tested to improve phosphopeptides recovery and enrichment selectivity. Finally, the analysis of isolated peptides pointed out that polydopamine alone is an ideal support matrix for polar post translational modifications because it enables to reduce unspecific binding and preferentially binds hydrophilic peptides. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. Simultaneous determination of herbicide residues in tobacco using ultraperformance convergence chromatography coupled with solid-phase extraction.

    Science.gov (United States)

    Guo, Weiyun; Bian, Zhaoyang; Zhang, Daohong; Tang, Gangling; Liu, Wei; Wang, Jianlong; Li, Zhonghao; Yang, Fei

    2015-03-01

    A time-saving and organic solvent efficient method to simultaneously determine six kinds of herbicide residues in tobacco using solid-phase extraction for sample clean-up and preconcentration and the highly sensitive ultraperformance convergence chromatography method was developed. Parameters for ultraperformance convergence chromatography, including the choice of stationary phase and modifiers, autobackpressure regulator pressure, column temperature, and the flow rate of mobile solvents, were optimized. The herbicide residues of napropamide, alachlor, quizalofop-ethyl, diphenamid, metolachlor, and clomazone in tobacco samples were successfully separated and detected at levels as low as 0.0043-0.0086 mg/kg within 5 min using a nonpolar high strength silica C18 selectivity for bases column and methanol as the cosolvent of the mobile phase of carbon dioxide (75-99.9%, v/v). Analysis of tobacco samples had recoveries of 69.8-95.0%, limit of quantitation of 0.0127-0.0245 mg/kg, limit of detection of 0.0043-0.0086 mg/kg, and correlation coefficient of >0.9990. Results support this method as an efficient alternative to current methodologies for the determination of herbicide residues in tobacco.

  11. Determination of trace copper in food samples by flame atomic absorption spectrometry after solid phase extraction on modified soybean hull

    Energy Technology Data Exchange (ETDEWEB)

    Xiang Guoqiang, E-mail: xianggq@126.com [School of Chemistry and Chemical Engineering, Henan University of Technology, Zhengzhou 450001 (China); Zhang Yingming; Jiang Xiuming; He Lijun; Fan Lu; Zhao Wenjie [School of Chemistry and Chemical Engineering, Henan University of Technology, Zhengzhou 450001 (China)

    2010-07-15

    Soybean hull was chemically modified with citric acid and used as a solid phase extraction adsorbent for the determination of trace amounts of Cu{sup 2+} in food samples by flame absorption spectrometry (FAAS). The effect of pH, sample flow rate and volume, elution flow rate and volume and co-existing ions on the recovery of the analyte were investigated. The results showed that Cu{sup 2+} could be adsorbed on the modified soybean hull at pH 8.0 and eluted by 2.0 mL of 1.0 mol L{sup -1} HCl. Under the optimized conditions, the adsorption capacity of modified soybean hull was found to be 18.0 mg g{sup -1} for Cu{sup 2+}. The detection limit of the proposed method was 0.8 ng mL{sup -1} for Cu{sup 2+} with an enrichment factor of 18. The analytical result for the certified reference tea sample (GBW07605) was in a good agreement with the certified value. The proposed method has also been successfully applied to the determination of trace Cu{sup 2+} in dried sweet potato, lake water and milk powder, the recovery of Cu{sup 2+} for spiked samples was between 91% and 109.6%.

  12. Determination of pinocembrin in human plasma by solid-phase extraction and LC/MS/MS: application to pharmacokinetic studies.

    Science.gov (United States)

    Yan, Bei; Cao, Guoying; Sun, Taohua; Zhao, Xi; Hu, Xin; Yan, Jiling; Peng, Yueying; Shi, Aixin; Li, Yang; Xue, Wei; Li, Min; Li, Kexin; Liu, Yingfa

    2014-12-01

    A sensitive, fast and specific method for the quantitation of pinocembrin in human plasma based on high-performance liquid chromatography-tandem mass spectrometry (LC/MS/MS) was developed and validated. Clonazepam was used as the internal standard (IS). After solid-phase extraction of 500 μL plasma, pinocembrin and the IS were separated on a Luna C8 column using the mobile phase composed of acetonitrile-0.3 mm ammonium acetate solution (65:35, v/v) at a flow rate of 0.25 mL/min in isocratic mode. The detection was performed on a triple quadrupole tandem mass spectrometer by multiple reaction monitoring via an electrospray ionization source in negative mode by AB SCIEX Qtrap 5500. The assay was linear from 1 to 400 ng/mL, with within- and between-run accuracy (relative error) from -1.82 to 0.54%, and within- and between-run precision (CV) below 5.25%. The recovery was above 88% for the analyte at 1, 50 and 300 ng/mL. This analytical method was successful for the determination of pinocembrin in human plasma and applied to a pharmacokinetic study of pinocembrin injection in healthy volunteers after intravenous drip administration. Copyright © 2014 John Wiley & Sons, Ltd.

  13. Multifunctional silver nanoparticle-doped silica for solid-phase extraction and surface-enhanced Raman scattering detection

    Science.gov (United States)

    Markina, Natalia E.; Markin, Alexey V.; Zakharevich, Andrey M.; Gorin, Dmitry A.; Rusanova, Tatiana Yu.; Goryacheva, Irina Yu.

    2016-12-01

    Multifunctional silica gel with embedded silver nanoparticles (SiO2-AgNP) is proposed for application as sorbent for solid-phase extraction (SPE) and simultaneously as substrate for surface-enhanced Raman spectroscopy (SERS) due to their high sorption properties and ability to enhance Raman signal (SERS-active sorbents). SiO2-AgNP was synthesized via alkaline hydrolysis of tetraethyl orthosilicate with simultaneous reduction of silver ions to silver nanoparticles (AgNP) within the SiO2 bulk. Synthesis of AgNP directly to the SiO2 matrix enables to exclude any additional stabilizers for the nanoparticles that educes signal-to-noise ratio during SERS measurement. Apart from Raman spectroscopy, obtained sorbents were also characterized by scanning electron microscopy and UV-visible diffuse reflectance spectroscopy. The influence of AgNO3 concentration used during the SiO2-AgNP synthesis on its gelling time, color, diffuse reflectance spectra, and enhancement of Raman signal was investigated. A Raman enhancement factor of SiO2-AgNP with optimal composition was around 105. Finally, the sorbents were applied for SPE and subsequent SERS detection of model compounds (rhodamine 6G and folic acid). It was found that SPE enables to decrease detectable concentrations by two orders. Therefore, SPE combined with SERS has high potential for further analytical investigations.

  14. Determination of artificial sweeteners in water samples by solid-phase extraction and liquid chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Ordóñez, Edgar Y; Quintana, José Benito; Rodil, Rosario; Cela, Rafael

    2012-09-21

    The development and performance evaluation of an analytical method for the determination of six artificial sweeteners in environmental waters using solid-phase extraction (SPE) followed by liquid chromatography-tandem mass spectrometry are presented. To this end, different SPE alternatives have been evaluated: polymeric reversed-phase (Oasis HLB, Env+, Plexa and Strata X), and mixed-mode with either weak (Oasis WAX) or strong anionic-exchange (Oasis MAX and Plexa PAX) sorbents. Among them, reversed-phase sorbents, particularly Oasis HLB and Strata X, showed the best performance. Oasis HLB provided good trueness (recoveries: 73-112%), precision (RSD<10%) and limits of quantification (LOQ: 0.01-0.5 μg/L). Moreover, two LC separation mechanisms were evaluated: reversed-phase (RPLC) and hydrophilic interaction (HILIC), with RPLC providing better performance than HILIC. The final application of the method showed the presence of acesulfame, cyclamate, saccharin and sucralose in the wastewater and surface water samples analyzed at concentrations up to 54 μg/L.

  15. Speciation of Cr(III) and Cr(VI) after column solid phase extraction on Amberlite XAD-2010.

    Science.gov (United States)

    Bulut, V N; Duran, C; Tufekci, M; Elci, L; Soylak, M

    2007-05-08

    A speciation procedure for Cr(III) and Cr(VI) based on column solid phase extraction on Amberlite XAD-2010 and flame atomic absorption spectrometry combination. Cr(VI) was quantitatively recovered on Amberlite XAD-2010 resin at pH range of 2.0-3.0 as its diethyldithiocarbamate complex, while the recoveries of Cr(III) was below 5%. The influences of the various parameters including amounts of the reagents, eluent type and its volume, sample volume, etc., on the quantitative recoveries were examined. The interference of matrix and coexistent elements for method were studied. The detection limit (corresponding to three times the standard deviation of the blank) and the enrichment factor for Cr(VI) were found to be 1.28 microg/L and 25, respectively. To verify the accuracy of the method, drinking water certified reference material (CRM-TMDW-500) was analyzed and the results obtained were in good agreement with the certified value. The proposed method has been successfully applied to the speciation of Cr(III) and Cr(VI) in water samples and preconcentration of total chromium in environmental samples.

  16. Simultaneous detection of trace metal ions in water by solid phase extraction spectroscopy combined with multivariate calibration.

    Science.gov (United States)

    Wang, Lei; Cao, Peng; Li, Wei; Tong, Peijin; Zhang, Xiaofang; Du, Yiping

    2016-04-15

    Solid Phase Extraction Spectroscopy (SPES) developed in this paper is a technique to measure spectrum directly on the solid phase material where the analytes are concentrated in SPE process. Membrane enrichment and UV-Visible spectroscopy were utilized to fulfill SPES, and multivariate calibration method of partial least squares (PLS) was used to simultaneously detect the concentrations of trace cobalt (II) and zinc (II) in water samples. The proposed method is simple, sensitive and selective. The complexes of analyte ions were collected on the cellulose acetate membranes via membrane filtration after the complexation reaction with 1-2-pyridylazo 2-naphthol (PAN). The spectra of the membranes which contained the complexes of metal ions and PAN were measured directly without eluting. The analytical conditions including pH, reaction time, sample volume, the amount of PAN, and flow rates were optimized. Nonionic surfactant Brij-30 was absorbed on the membranes prior to SPES to modify the membranes for improving the enrichment and spectrum measurement. The interference from other ions to the determination was investigated. Under the optimal condition, the absorbance was linearly related to the concentration at the range of 0.1-3.0 μg/L and 0.1-2.0 μg/L, with the correlation coefficients (R(2)) of 0.9977 and 0.9951 for Co (II) and Zn (II), respectively. The limits of detection were 0.066 μg/L for cobalt (II) and 0.104 μg/L for zinc (II). PLS regression with leave-one-out cross-validation was utilized to build models to detect cobalt (II) and zinc (II) in drinking water samples simultaneously. The correlation coefficient between ion concentration and spectrum of calibration set and independent prediction set were 1.0000 and 0.9974 for cobalt (II) and 1.0000 and 0.9956 for zinc (II). For cobalt (II) and zinc (II), the errors of the prediction set were in the range 0.0406-0.1353 μg/L and 0.0025-0.1884 μg/L. Copyright © 2016. Published by Elsevier B.V.

  17. Dispersive micro-solid phase extraction based on self-assembling, ionic liquid-coated magnetic particles for the determination of clofentezine and chlorfenapyr in environmental water samples.

    Science.gov (United States)

    Peng, Bing; Zhang, Jiaheng; Lu, Runhua; Zhang, Sanbing; Zhou, Wenfeng; Gao, Haixiang

    2013-11-21

    Two ionic liquid-coated-Fe3O4 magnetic particles (IL-Fe3O4 MPs) were developed for use in two types of dispersive micro-solid phase extraction (D-μ-SPE) for the high-performance liquid chromatographic analysis of clofentezine and chlorfenapyr in environmental water samples. Self-assembling IL-Fe3O4 MPs were used in D-μ-SPE as adsorbents. Two D-μ-SPE extraction methods, namely, direct dispersive micro-solid phase extraction (d-D-μ-SPE) and in situ solvent formation-based dispersive micro-solid phase extraction (ISF-D-μ-SPE), were proposed, using [C8MIM][PF6] to extract analytes through two pathways. Lower IL doses were required in the extraction process compared with those in other IL-based methods. Fe3O4 MPs can also be recycled and reused after extraction and are thus environmentally friendly. These newly developed methods were demonstrated to be feasible for use in the quantitation of clofentezine and chlorfenapyr at trace levels, with lower limit of detection values ranging from 0.4 to 0.5 ng mL(-1) for d-D-μ-SPE and 0.4 ng mL(-1) for ISF-D-μ-SPE. Finally, relative standard deviations of less than 6.0% were obtained.

  18. Ultrapreconcentration and determination of organophosphorus pesticides in water by solid-phase extraction combined with dispersive liquid-liquid microextraction and high-performance liquid chromatography.

    Science.gov (United States)

    Chen, Junhua; Zhou, Guangming; Deng, Yongli; Cheng, Hongmei; Shen, Jie; Gao, Yi; Peng, Guilong

    2016-01-01

    Solid-phase extraction coupled with dispersive liquid-liquid microextraction was developed as an ultra-preconcentration method for the determination of four organophosphorus pesticides (isocarbophos, parathion-methyl, triazophos and fenitrothion) in water samples. The analytes considered in this study were rapidly extracted and concentrated from large volumes of aqueous solutions (100 mL) by solid-phase extraction coupled with dispersive liquid-liquid microextraction and then analyzed using high performance liquid chromatography. Experimental variables including type and volume of elution solvent, volume and flow rate of sample solution, salt concentration, type and volume of extraction solvent and sample solution pH were investigated for the solid-phase extraction coupled with dispersive liquid-liquid microextraction with these analytes, and the best results were obtained using methanol as eluent and ethylene chloride as extraction solvent. Under the optimal conditions, an exhaustive extraction for four analytes (recoveries >86.9%) and high enrichment factors were attained. The limits of detection were between 0.021 and 0.15 μg/L. The relative standard deviations for 0.5 μg/L of the pesticides in water were in the range of 1.9-6.8% (n = 5). The proposed strategy offered the advantages of simple operation, high enrichment factor and sensitivity and was successfully applied to the determination of four organophosphorus pesticides in water samples.

  19. Parameters optimization using experimental design for headspace solid phase micro-extraction analysis of short-chain chlorinated paraffins in waters under the European water framework directive.

    Science.gov (United States)

    Gandolfi, F; Malleret, L; Sergent, M; Doumenq, P

    2015-08-07

    The water framework directives (WFD 2000/60/EC and 2013/39/EU) force European countries to monitor the quality of their aquatic environment. Among the priority hazardous substances targeted by the WFD, short chain chlorinated paraffins C10-C13 (SCCPs), still represent an analytical challenge, because few laboratories are nowadays able to analyze them. Moreover, an annual average quality standards as low as 0.4μgL(-1) was set for SCCPs in surface water. Therefore, to test for compliance, the implementation of sensitive and reliable analysis method of SCCPs in water are required. The aim of this work was to address this issue by evaluating automated solid phase micro-extraction (SPME) combined on line with gas chromatography-electron capture negative ionization mass spectrometry (GC/ECNI-MS). Fiber polymer, extraction mode, ionic strength, extraction temperature and time were the most significant thermodynamic and kinetic parameters studied. To determine the suitable factors working ranges, the study of the extraction conditions was first carried out by using a classical one factor-at-a-time approach. Then a mixed level factorial 3×2(3) design was performed, in order to give rise to the most influent parameters and to estimate potential interactions effects between them. The most influent factors, i.e. extraction temperature and duration, were optimized by using a second experimental design, in order to maximize the chromatographic response. At the close of the study, a method involving headspace SPME (HS-SPME) coupled to GC/ECNI-MS is proposed. The optimum extraction conditions were sample temperature 90°C, extraction time 80min, with the PDMS 100μm fiber and desorption at 250°C during 2min. Linear response from 0.2ngmL(-1) to 10ngmL(-1) with r(2)=0.99 and limits of detection and quantification, respectively of 4pgmL(-1) and 120pgmL(-1) in MilliQ water, were achieved. The method proved to be applicable in different types of waters and show key advantages, such

  20. Multiple solid-phase microextraction

    NARCIS (Netherlands)

    Koster, EHM; de Jong, GJ

    2000-01-01

    Theoretical aspects of multiple solid-phase microextraction are described and the principle is illustrated with the extraction of lidocaine from aqueous solutions. With multiple extraction under non-equilibrium conditions considerably less time is required in order to obtain an extraction yield that

  1. High-throughput assay for quantification of the plasma concentrations of thiopental using automated solid phase extraction (SPE) directly coupled to LC-MS/MS instrumentation.

    Science.gov (United States)

    Moosavi, Seyed Mojtaba; Shekar, Kiran; Fraser, John; Smith, Maree T; Ghassabian, Sussan

    2016-12-01

    Most previous assays for thiopental are time-consuming due to laborious sample extraction steps prior to analysis using gas chromatography or high pressure liquid chromatography. Here, we describe the first high-throughput liquid chromatography - tandem mass spectrometry (LC-MS/MS) method for quantification of thiopental concentrations in samples of human plasma. Robotic on-line solid phase extraction (SPE) was used to elute the analytes of interest from samples of human plasma (50μL) loaded onto C18 SPE cartridges to which were added aliquots (50μL) of internal standard solution (thiopental-d5 100ng/mL) and 0.5% formic acid in water (100μL). Cartridges were washed using 10% methanol in ammonium acetate buffer (50mM, pH 7) before elution with mobile phase comprising 0.1% formic acid in water and acetonitrile with a flow rate of 0.55mL/min using a 7.2min run time. The analytes were separated on a C18 XTerra(®) analytical column. Mass spectrometry detection was performed using a QTrap 5500 mass spectrometer (AB Sciex) with negative ionisation. The multiple reaction monitoring (MRM) transitions for thiopental and the internal standard were 241→58, and 246→58, respectively. The calibration curve was linear over a range of 6-600ng/mL. Thiopental was stable in human plasma samples for at least 36h in the autosampler, as well as after three cycles of freeze and thaw, and after 3h storage at room temperature. The absolute recovery and matrix effect were 102% and 6.9%, respectively, and the within-run and between-run precision and accuracy were ≤15%. Our method is fully-validated and satisfies the requirements of the 2012 European Medicines Agency (EMEA) guideline for Bioanalytical Method Validation. Copyright © 2016 Elsevier B.V. All rights reserved.

  2. All-in-one solid-phase microextraction: Development of a selective solid-phase microextraction fiber assembly for the simultaneous and efficient extraction of analytes with different polarities.

    Science.gov (United States)

    Gharari, Hossein; Farjaminezhad, Manoochehr; Marefat, Abdolrahim; Fakhari, Ali Reza

    2016-05-01

    In the present work, for the first time, an all-in-one solid-phase microextraction technique was developed for the simultaneous and efficient extraction of analytes within a vast polarity range. A novel fiber assembly composed of two different steel components each coated with different coatings (polydimethylsiloxane and polyethylene glycol) in terms of polarity by sol-gel technology was employed for the extraction of model compounds of different polarity in a single run followed by gas chromatography with mass spectrometry. Effective parameters in the extraction step and gas chromatography with mass spectrometry analysis were optimized for all model compounds. The detection limits of the developed method for model compounds were below 0.2 ng/L. The repeatability and reproducibility of the proposed method, explained by relative standard deviation, varied between 7.22 and 9.15% and between 7.95 and 14.90 (n = 5), respectively. Results showed that, under random conditions, compared to separate extractions performed by two other differently end-coated components that had not been assembled as the final dual fiber, as two individual fibers; simultaneous, efficient and relatively selective extraction of all model compounds was obtained in a single run by the proposed all-in-one technique. Finally, the optimized procedure was applied to extraction and determination of the model compounds in spiked water samples.

  3. Preconcentration and Determination of Mefenamic Acid in Pharmaceutical and Biological Fluid Samples by Polymer-grafted Silica Gel Solid-phase Extraction Following High Performance Liquid Chromatography

    OpenAIRE

    Bagheri Sadeghi, Hayedeh; Panahi, Homayon Ahmad; Mahabadi, Mahsa; Moniri, Elham

    2015-01-01

    Mefenamic acid is a nonsteroidal anti-inflammatory drug (NSAID) that has analgesic, anti-infammatory and antipyretic actions. It is used to relieve mild to moderate pains. Solid-phase extraction of mefenamic acid by a polymer grafted to silica gel is reported. Poly allyl glycidyl ether/iminodiacetic acid-co-N, N-dimethylacrylamide was synthesized and grafted to silica gel and was used as an adsorbent for extraction of trace mefenamic acid in pharmaceutical and biological samples. Different fa...

  4. Study on the determination of polyphenols in tobacco by HPLC coupled with ESI-MS after solid-phase extraction.

    Science.gov (United States)

    Li, Zhong; Wang, Lan; Yang, Guangyu; Shi, Honglin; Jiang, Ciqing; Liu, Wei; Zhang, Yunhuai

    2003-01-01

    A high-performance liquid chromatography method coupled with electrospray ionization-mass spectrometry for the determination of polyphenols in tobacco is studied. The polyphenols are extracted from a tobacco sample by being refluxed in a boiling water bath with 80% methanol and purified by solid-phase extraction with a C18 cartridge. The chlorogenic acid, rutin, scopoletin, caffeic acid, scopolin, and other polyphenols are satisfactorily separated on a Nova-Pak C18 chromatographic column (3.9 x 150 mm) with methanol and 0.05 mol/L potassium dihydrogen phosphate buffer solution gradient elution as mobile phase at a flow rate of 0.5 mL/min. Each of the polyphenols is monitored by photodiode array detector at its maximum wavelength: chlorogenic acid, 326.1 nm; rutin, 354.8 nm; scopoletin, 344.0 nm; caffeic acid, 323.7 nm; and scopolin, 365.2 nm. The limits of detection are: 100 ng/mL for chlorogenic acid, 125 ng/mL for rutin, 60 ng/mL for scopoletin, 50 ng/mL for caffeic acid, and 100 ng/mL for scopolin. The key polyphenols in tobacco are identified by comparing the retention time, the UV-spectrum, and the mass spectra with those of the standards. The recovery of tobacco polyphenols is 94-105%, and the relative standard deviations are 1.28-1.49%. This method is successfully applied to qualitatively and quantitatively analyze the polyphenols in tobacco with good results.

  5. Advanced functional materials in solid phase extraction for ICP-MS determination of trace elements and their species - A review.

    Science.gov (United States)

    He, Man; Huang, Lijin; Zhao, Bingshan; Chen, Beibei; Hu, Bin

    2017-06-22

    For the determination of trace elements and their species in various real samples by inductively coupled plasma mass spectrometry (ICP-MS), solid phase extraction (SPE) is a commonly used sample pretreatment technique to remove complex matrix, pre-concentrate target analytes and make the samples suitable for subsequent sample introduction and measurements. The sensitivity, selectivity/anti-interference ability, sample throughput and application potential of the methodology of SPE-ICP-MS are greatly dependent on SPE adsorbents. This article presents a general overview of the use of advanced functional materials (AFMs) in SPE for ICP-MS determination of trace elements and their species in the past decade. Herein the AFMs refer to the materials featuring with high adsorption capacity, good selectivity, fast adsorption/desorption dynamics and satisfying special requirements in real sample analysis, including nanometer-sized materials, porous materials, ion imprinting polymers, restricted access materials and magnetic materials. Carbon/silica/metal/metal oxide nanometer-sized adsorbents with high surface area and plenty of adsorption sites exhibit high adsorption capacity, and porous adsorbents would provide more adsorption sites and faster adsorption dynamics. The selectivity of the materials for target elements/species can be improved by using physical/chemical modification, ion imprinting and restricted accessed technique. Magnetic adsorbents in conventional batch operation offer unique magnetic response and high surface area-volume ratio which provide a very easy phase separation, greater extraction capacity and efficiency over conventional adsorbents, and chip-based magnetic SPE provides a versatile platform for special requirement (e.g. cell analysis). The performance of these adsorbents for the determination of trace elements and their species in different matrices by ICP-MS is discussed in detail, along with perspectives and possible challenges in the future

  6. Magnetic porous β-cyclodextrin polymer for magnetic solid-phase extraction of microcystins from environmental water samples.

    Science.gov (United States)

    Zhang, Wenmin; Lin, Mingxia; Wang, Meili; Tong, Ping; Lu, Qiaomei; Zhang, Lan

    2017-06-23

    Microcystins (MCs) are cyclic heptapeptide toxins and tumor promoters produced by cyanobacteria, which threaten the health of humans. In this study, magnetic porous β-cyclodextrin polymer (Fe3O4@SiO2@P-CDP) was synthesized and characterized by transmission electron microscopy, scanning electron microscopy, energy dispersive X-ray spectrometry, Fourier transform infrared spectrometry, X-ray diffraction, nitrogen adsorption porosimetry and vibrating sample magnetometer. The synthesized Fe3O4@SiO2@P-CDP particles were then used for magnetic solid-phase extraction (MSPE) of MCs from environmental water samples, and exhibited excellent extraction performance, especially for MC-RR. Coupled with high-performance liquid chromatography with tandem mass spectrometry (HPLC-MS/MS), a simple, efficient and sensitive method for determination of trace levels of MCs was established. After the optimization of conditions, wide linear ranges (2.0-1000pgmL(-1)), good linearity (r(2)≥0.9996) and acceptable repeatability (RSD≤9.4%, n=5) were obtained. The limits of detection (LODs, S/N=3) and limits of quantification (LOQs, S/N=10) for three MCs (MC-LR, MC-RR and MC-YR) were in the range of 1.0-2.0pgmL(-1) and 2.0-5.0pgmL(-1), respectively. Typical water samples were analyzed by the developed method, and trace levels of MC-LR and MC-RR were detected. The results demonstrate that the developed method has great potential for the determination of MCs in complicated matrix. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. Analysis of Mars Analogue Soil Samples Using Solid-Phase Microextraction, Organic Solvent Extraction and Gas Chromatography/Mass Spectrometry

    Science.gov (United States)

    Orzechowska, G. E.; Kidd, R. D.; Foing, B. H.; Kanik, I.; Stoker, C.; Ehrenfreund, P.

    2011-01-01

    Polycyclic aromatic hydrocarbons (PAHs) are robust and abundant molecules in extraterrestrial environments. They are found ubiquitously in the interstellar medium and have been identified in extracts of meteorites collected on Earth. PAHs are important target molecules for planetary exploration missions that investigate the organic inventory of planets, moons and small bodies. This study is part of an interdisciplinary preparation phase to search for organic molecules and life on Mars. We have investigated PAH compounds in desert soils to determine their composition, distribution and stability. Soil samples (Mars analogue soils) were collected at desert areas of Utah in the vicinity of the Mars Desert Research Station (MDRS), in the Arequipa region in Peru and from the Jutland region of Denmark. The aim of this study was to optimize the solid-phase microextraction (SPME) method for fast screening and determination of PAHs in soil samples. This method minimizes sample handling and preserves the chemical integrity of the sample. Complementary liquid extraction was used to obtain information on five- and six-ring PAH compounds. The measured concentrations of PAHs are, in general, very low, ranging from 1 to 60 ng g(sup -1). The texture of soils is mostly sandy loam with few samples being 100% silt. Collected soils are moderately basic with pH values of 8-9 except for the Salten Skov soil, which is slightly acidic. Although the diverse and variable microbial populations of the samples at the sample sites might have affected the levels and variety of PAHs detected, SPME appears to be a rapid, viable field sampling technique with implications for use on planetary missions.

  8. Novel surface dummy molecularly imprinted silica as sorbent for solid-phase extraction of bisphenol A from water samples.

    Science.gov (United States)

    Hu, Xiaolei; Wu, Xiao; Yang, Fanfan; Wang, Qiang; He, Chiyang; Liu, Shaorong

    2016-01-01

    A novel surface molecularly imprinted silica composite was prepared by a dummy-template imprinting strategy for the solid-phase extraction (SPE) of bisphenol A (BPA). 2,2-Bis(4-hydroxyphenyl) hexafluoropropane (BPAF) was chosen as the template molecule, and a hybrid technique was used for imprinting procedure. The imprinted silica was characterized by FT-IR spectroscopy, scanning electron microscope, thermo-gravimetric analysis, and nitrogen adsorption-desorption isotherms. The static binding test verified that the imprinted silica had much higher recognition ability for BPA than the non-imprinted silica, and the kinetic adsorption test presented the fast binding kinetics of the surface imprinted silica for BPA. When used as a SPE sorbent, the imprinted silica showed high extraction efficiencies and high enrichment factor for BPA. Based on the imprinted silica, a SPE-HPLC-UV method was developed and successfully applied to the detection of BPA in BPA-spiked lake water, tap water and drinking water samples with a high recovery of 97.3-106.0%, a RSD of 1.2-3.8% (n=3) and a limit of detection (S/N=3) of 0.3 ng/mL. The analysis results of a certified BPA sample also demonstrated the reliability of present method. The new surface dummy molecularly imprinted silica completely avoided the interference of the residual template molecules and greatly improved the binding kinetic of the target molecules. Therefore, it can be used as a good sorbent for SPE of BPA in environmental water samples.

  9. In-line micro-matrix solid-phase dispersion extraction for simultaneous separation and extraction of Sudan dyes in different spices.

    Science.gov (United States)

    Rajabi, Maryam; Sabzalian, Sedigheh; Barfi, Behruz; Arghavani-Beydokhti, Somayeh; Asghari, Alireza

    2015-12-18

    A novel, simple, fast, and miniaturized method, termed in-line micro-matrix solid-phase dispersion (in-line MMSPD), coupled with high performance liquid chromatography (HPLC) was developed for the simultaneous extraction and determination of Sudan dyes (i.e. Sudan I-IV, Sudan orange G, Sudan black B, and Sudan red G) with the aid of an experimental design strategy. In this method, a matrix solid-phase dispersion (MSPD) column including a suitable mixture of polar sorbents was inserted in the mobile phase pathway, and while the interfering compounds were retained, the analytes were eluted and entered into the analytical column. In this way, the extraction, elution, and separation of the analytes were performed sequentially. Under the optimal experimental conditions (including the amount of sample, 0.0426g; amount of dispersant phase, 0.0216g of florisil, 0.0227g of silica, 0.0141g of alumina; and blending time, 112s), the limits of detection (LODs), limits of quantification, linear dynamic ranges, and recoveries were obtained to be 0.3-15.3μgkg(-1), 1-50μgkg(-1), 50-28,000μgkg(-1), and 94.5-99.1%, respectively. The results obtained showed that determination of the selected Sudan dyes in food samples using an enough sensitive and a simple analytically validated method like in-line MMSPD may offer a suitable screening method, which could be useful for food analysis and adulteration.

  10. Novel solid-phase membrane tip extraction and gas chromatography with mass spectrometry methods for the rapid analysis of triazine herbicides in real waters.

    Science.gov (United States)

    Sanagi, Mohd Marsin; Muhammad, Sarmad S; Hussain, Iqbal; Ibrahim, Wan Aini Wan; Ali, Imran

    2015-02-01

    Novel, fast, selective, eco-friendly and reproducible solid-phase membrane tip extraction and gas chromatography with mass spectrometry methods were developed and validated for the analysis of triazine herbicides (atrazine and secbumeton) in stream and lake waters. The retention times of atrazine and secbumeton were 7.48 and 8.51 min. The solid-phase membrane tip extraction was carried out in semiautomated dynamic mode on multiwall carbon nanotubes enclosed in a cone-shaped polypropylene membrane cartridge. Acetone and methanol were found as the best preconditioning and desorption solvents, respectively. The extraction and desorption times for these herbicides were 15.0 and 10.0 min, respectively. The percentage recoveries of atrazine and secbumeton were 88.0 and 99.0%. The linearity range was 0.50-80.0 μg/L (r(2) > 0.994), with detection limits (extraction made these methods novel. The Solid-phase membrane tip extraction method was optimized by considering the effect of extraction time, desorbing solvents and time.

  11. Molecularly imprinted solid-phase extraction for the selective determination of methamphetamine, amphetamine, and methylenedioxyphenylalkylamine designer drugs in human whole blood by gas chromatography-mass spectrometry.

    Science.gov (United States)

    Kumazawa, Takeshi; Hasegawa, Chika; Hara, Kenji; Uchigasaki, Seisaku; Lee, Xiao-Pen; Seno, Hiroshi; Suzuki, Osamu; Sato, Keizo

    2012-03-01

    A novel method is described for the extraction of methamphetamine, amphetamine, and methylenedioxyphenylalkylamine designer drugs, such as 3,4-methylenedioxy-methamphetamine, 3,4-methylenedioxyamphetamine, 3,4-methylenedioxyethylamphetamine, N-methyl-1-(3,4-methylenedioxyphenyl)-2-butanamine, and 3,4-(methylenedioxyphenyl)-2-butanamine, from human whole blood using molecularly imprinted solid-phase extraction as highly selective sample clean-up technique. Whole blood samples were diluted with 10 mmol/L ammonium acetate (pH 8.6) and applied to a SupelMIP-Amphetamine molecularly imprinted solid-phase extraction cartridge. The cartridge was then washed to eliminate interferences, and the amphetamines of interest were eluted with formic acid/methanol (1:100, v/v). After derivatization with trifluoroacetic anhydride, the analytes were quantified using gas chromatography-mass spectrometry. Recoveries of the seven amphetamines spiked into whole blood were 89.1-102%. The limits of quantification for each compound in 200 μL of whole blood were between 0.25 and 1.0 ng. The maximum intra- and inter-day coefficients of variation were 9.96 and 13.8%, respectively. The results show that methamphetamine, amphetamine, and methylenedioxyphenylalkyl-amine designer drugs can be efficiently extracted from crude biological samples such as whole blood by molecularly imprinted solid-phase extraction with good reproducibility. This extraction method will be useful for the pretreatment of human samples before gas chromatography-mass spectrometry.

  12. Analysis of the antioxidant butylated hydroxytoluene (BHT) in water by means of solid phase extraction combined with GC/MS.

    Science.gov (United States)

    Fries, Elke; Püttmann, Wilhelm

    2002-05-01

    The antioxidant 3,5-di-tert-butyl-4-hydroxy-toluene (BHT) is widely used as an additive to increase the tenability of food and plastics. BHT is degraded to 3,5-di-tert-butyl-4-hydroxybenzaldehyde (BHT-CHO) in mammals, as well as in the natural environment such as in water and soils. BHT-CHO has been studied extensively in terms of their potential toxicities. The present investigation was carried out to quantify BHT and BHT-CHO in river, ground, rain and drinking water obtained from several locations in Germany. Apart from the compounds mentioned above, 1,2-bis-(3,5-di-tert-butyl-4-hydroxyphenyl)ethane (2-BHT), which is a dimer of BHT, was also detected in the extracts of some ground water samples. The applied analytical method is based on solid phase extraction (SPE) to concentrate trace compounds from water samples followed by gas chromatography/mass spectrometry (GC/MS) of the extracts. A total of 51 of the respective water samples were used for extraction purposes and analyte recoveries were all > or = 80%. The determination limit for BHT was 5 ng l(-1) and for BHT-CHO 16 ng l(-1). The standard deviations for the analytical procedure were 6% for BHT and 10% for BHT-CHO. The use of the antioxidant BHT in Germany has resulted in water concentrations of 7-791 ng l(-1) in the rivers Rhine, Elbe, Main, Oder, Nidda and Schwarzbach. The degradation product BHT-CHO was also detected in the river water samples at concentrations between 29 and 223 ng l(-1). The concentrations of BHT measured in German rivers are lower compared to values measured in the USA and Japan 20 years ago. In ground water, levels for BHT varied from non-detectable up to 2156 ng l(-1) and for BHT-CHO from non-detectable up to 674 ng l(-1). Both compounds were also detected in rain water in Frankfurt/Main at a concentration of 1797 ng l(-1) for BHT and 59 ng l(-1) for BHT-CHO.

  13. Novel Functionalized Polythiophene-Coated Fe3O4 Nanoparticles for Magnetic Solid-Phase Extraction of Phthalates

    Directory of Open Access Journals (Sweden)

    Siti Nor Atika Baharin

    2016-04-01

    Full Text Available Poly(phenyl-(4-(6-thiophen-3-yl-hexyloxy-benzylidene-amine (P3TArH was successfully synthesized and coated on the surface of Fe3O4 magnetic nanoparticles (MNPs. The nanocomposites were characterized by Fourier transform infra-red (FTIR, X-ray diffractometry (XRD, Brunauer-Emmett-Teller (BET surface area analysis, analyzer transmission electron microscopy (TEM and vibrating sample magnetometry (VSM. P3TArH-coated MNPs (MNP@P3TArH showed higher capabilities for the extraction of commonly-used phthalates and were optimized for the magnetic-solid phase extraction (MSPE of environmental samples. Separation and determination of the extracted phthalates, namely dimethyl phthalate (DMP, diethyl phthalate (DEP, dipropyl phthalate (DPP, dibutyl phthalate (DBP, butyl benzyl phthalate (BBP, dicyclohexyl phthalate (DCP, di-ethylhexyl phthalate (DEHP and di-n-octyl phthalate (DNOP, were conducted by a gas chromatography-flame ionization detector (GC-FID. The best working conditions were as follows; sample at pH 7, 30 min extraction time, ethyl acetate as the elution solvent, 500-µL elution solvent volumes, 10 min desorption time, 10-mg adsorbent dosage, 20-mL sample loading volume and 15 g·L−1 concentration of NaCl. Under the optimized conditions, the analytical performances were determined with a linear range of 0.1–50 µg·L−1 and a limit of detection at 0.08–0.468 µg·L−1 for all of the analytes studied. The intra-day (n = 7 and inter-day (n = 3 relative standard deviations (RSD% of three replicates were each demonstrated in the range of 3.7–4.9 and 3.0–5.0, respectively. The steadiness and reusability studies suggested that the MNP@P3TArH could be used up to five cycles. The proposed method was executed for the analysis of real water samples, namely commercial bottled mineral water and bottled fresh milk, whereby recoveries in the range of 68%–101% and RSD% lower than 7.7 were attained.

  14. Magnetic solid-phase extraction of brominated flame retardants from environmental waters with graphene-doped Fe3O4 nanocomposites.

    Science.gov (United States)

    Yang, Jing; Qiao, Jun-qin; Cui, Shi-hai; Li, Jia-yuan; Zhu, Jin-jin; Yin, He-xing; Zhan, Cheng-yan; Lian, Hong-zhen

    2015-06-01

    Graphene-doped Fe3O4 nanocomposites were prepared by a solvothermal reaction of an iron source with graphene. The nanocomposites were characterized by transmission electron microscopy, atomic force microscopy, X-ray diffraction, superconducting quantum interference, Raman spectroscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. This nanomaterial has been used as a magnetic solid-phase extraction sorbent to extract trace brominated flame retardants from environmental waters. Various extraction parameters were optimized including dosage and reusability of the nanocomposites, and pH of sample matrix. The reliability of the magnetic solid-phase extraction protocol based on graphene-doped Fe3O4 nanocomposites was evaluated by investigating the recoveries of 2,4,6-tribromophenol, tetrabromobisphenol A, 4-bromodiphenyl ether, and 4,4'-dibromodiphenyl ether in water samples. Good recoveries (85.0-105.0%) were achieved with the relative standard deviation ranging from 1.1-7.1%. Moreover, it is speculated from characterization and magnetic solid-phase extraction experiment that there is not only π-π stacking but also possible hydrophobic interaction between the graphene-doped Fe3O4 nanocomposites and analytes. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Application of mercapto-silica polymerized high internal phase emulsions for the solid-phase extraction and preconcentration of trace lead(II).

    Science.gov (United States)

    Su, Rihui; Ruan, Guihua; Chen, Zhengyi; Du, Fuyou; Li, Jianping

    2015-12-01

    A new class of solid-phase extraction column prepared with grafted mercapto-silica polymerized high internal phase emulsion particles was used for the preconcentration of trace lead. First, mercapto-silica polymerized high internal phase emulsion particles were synthesized by using high internal phase emulsion polymerization and carefully assembled in a polyethylene syringe column. The influences of various parameters including adsorption pH value, adsorption and desorption solvents, flow rate of the adsorption and desorption procedure were optimized, respectively, and the suitable uploading sample volumes, adsorption capacity, and reusability of solid phase extraction column were also investigated. Under the optimum conditions, Pb(2+) could be preconcentrated quantitatively over a wide pH range (2.0-5.0). In the presence of foreign ions, such as Na(+) , K(+) , Ca(2+) , Zn(2+) , Mg(2+) , Cu(2+) , Fe(2+) , Cd(2+) , Cl(-) and NO3 (-) , Pb(2+) could be recovered successfully. The prepared solid-phase extraction column performed with high stability and desirable durability, which allowed more than 100 replicate extractions without measurable changes of performance. The feasibility of the developed method was further validated by the extraction of Pb(2+) in rice samples. At three spiked levels of 40.0, 200 and 800 μg/kg, the average recoveries for Pb(2+) in rice samples ranged from 87.3 to 105.2%.

  16. Application of Deep Eutectic Solvents in Hybrid Molecularly Imprinted Polymers and Mesoporous Siliceous Material for Solid-Phase Extraction of Levofloxacin from Green Bean Extract.

    Science.gov (United States)

    Li, Xiaoxia; Row, Kyung Ho

    2017-01-01

    Deep eutectic solvents (DES) are potential ecofriendly surfactants for the preparation of materials. In this study, both molecularly imprinted polymers (MIPs) and mesoporous siliceous materials (MSMs) were modified by betaine-based DES. Six materials were employed as solid phase extraction (SPE) adsorbents for the rapid purification of levofloxacin. The DES-based materials showed better selective adsorption than the conventional materials. The adsorption curves of DES-MIP showed superior molecular recognition ability and binding capability for levofloxacin compared to the other materials. The limit of detection and limit of quantitation of the method were 0.01 and 0.03 μg/mL for levofloxacin, respectively. The method recoveries at three spiked levels were 97.2 - 100.2% for DES-MIP, with an RSD <1.8%. DES-MIP showed the highest selective recovery (95.2%) for levofloxacin from the green bean extract, and could remove the interferent effectively.

  17. Submicrometric Magnetic Nanoporous Carbons Derived from Metal-Organic Frameworks Enabling Automated Electromagnet-Assisted Online Solid-Phase Extraction.

    Science.gov (United States)

    Frizzarin, Rejane M; Palomino Cabello, Carlos; Bauzà, Maria Del Mar; Portugal, Lindomar A; Maya, Fernando; Cerdà, Víctor; Estela, José M; Turnes Palomino, Gemma

    2016-07-19

    We present the first application of submicrometric magnetic nanoporous carbons (μMNPCs) as sorbents for automated solid-phase extraction (SPE). Small zeolitic imidazolate framework-67 crystals are obtained at room temperature and directly carbonized under an inert atmosphere to obtain submicrometric nanoporous carbons containing magnetic cobalt nanoparticles. The μMNPCs have a high contact area, high stability, and their preparation is simple and cost-effective. The prepared μMNPCs are exploited as sorbents in a microcolumn format in a sequential injection analysis (SIA) system with online spectrophotometric detection, which includes a specially designed three-dimensional (3D)-printed holder containing an automatically actuated electromagnet. The combined action of permanent magnets and an automatically actuated electromagnet enabled the movement of the solid bed of particles inside the microcolumn, preventing their aggregation, increasing the versatility of the system, and increasing the preconcentration efficiency. The method was optimized using a full factorial design and Doehlert Matrix. The developed system was applied to the determination of anionic surfactants, exploiting the retention of the ion-pairs formed with Methylene Blue on the μMNPC. Using sodium dodecyl sulfate as a model analyte, quantification was linear from 50 to 1000 μg L(-1), and the detection limit was equal to 17.5 μg L(-1), the coefficient of variation (n = 8; 100 μg L(-1)) was 2.7%, and the analysis throughput was 13 h(-1). The developed approach was applied to the determination of anionic surfactants in water samples (natural water, groundwater, and wastewater), yielding recoveries of 93% to 110% (95% confidence level).

  18. Core-Shell Diamond as a Support for Solid-Phase Extraction and High-Performance Liquid Chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Saini, Gaurav; Jensen, David S.; Wiest, Landon A.; Vail, Michael A.; Dadson, Andrew; Lee, Milton L.; Shutthanandan, V.; Linford, Matthew R.

    2010-06-01

    We report the formation of core-shell diamond particles for solid phase extraction (SPE) and high performance liquid chromatography (HPLC) made by layer-by-layer (LbL) deposition. Their synthesis begins with the amine functionalization of microdiamond by its immersion in an aqueous solution of a primary amine-containing polymer (polyallylamine (PAAm)). The amine-terminated microdiamond is then immersed in an aqueous suspension of nanodiamond, which leads to adsorption of the nanodiamond. Alternating (self-limiting) immersions in the solutions of the amine-containing polymer and the suspension of nanodiamond are continued until the desired number of nanodiamond layers is formed around the microdiamond. Finally, the core-shell particles are cross-linked with 1,2,5,6-diepoxycyclooctane or reacted with 1,2-epoxyoctadecane. Layer-by-layer deposition of PAAm and nanodiamond is also studied on planar Si/SiO2 surfaces, which were characterized by SEM, Rutherford backscattering spectrometry (RBS) and nuclear reaction analysis (NRA). Core-shell particles are characterized by diffuse reflectance infrared Fourier transform spectroscopy (DRIFT), environmental scanning electron microscopy (ESEM), and Brunauer Emmett Teller (BET) surface area and pore size measurements. Larger (ca. 50 μm) core-shell diamond particles have much higher surface areas, and analyte loading capacities in SPE than nonporous solid diamond particles. Smaller (ca. 3 μm), normal and reversed phase, core-shell diamond particles have been used for HPLC, with 36,300 plates per meter for mesitylene in a separation of benzene and alkyl benzenes on a C18 adsorbent, and 54,800 plates per meter for diazinon in a similar separation of two pesticides.

  19. Determination of resveratrol and piceid in beer matrices by solid-phase extraction and liquid chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Chiva-Blanch, Gemma; Urpi-Sarda, Mireia; Rotchés-Ribalta, Maria; Zamora-Ros, Raul; Llorach, Rafael; Lamuela-Raventós, Rosa Maria; Estruch, Ramon; Andrés-Lacueva, Cristina

    2011-02-04

    Beer is one of the most commonly consumed undistilled alcoholic beverages in many countries. In recent studies, the stilbenes resveratrol and piceid have been found in some hop varieties which are used in the production of beer. Therefore, they could be transferred to beer. The aim of the present work was to validate a method to study the potential content of trans- and cis-resveratrol and piceid in 110 commercial beers from around the world. The resveratrol and piceid contents of 110 beers were analyzed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) after a solid-phase extraction (SPE) using optimized and validated procedures for the beer matrix. The beer matrix effect was also studied. Stilbenes were found in quantifiable amounts in 92 beers, while concentrations below the limit of quantification (LOQ) were found in 18 beers. Resveratrol was found in the range of 1.34-77.0μg/L in 79% of the beers analyzed, and piceid was found in the range of 1.80-27.3μg/L in only 33% of them. The mean of total resveratrol in all the beers was 14.7±20.5μg/L. The content of resveratrol has been compared with other resveratrol containing foods. A serving of beer contains similar amounts of stilbenes as berries, less than chocolate and grape products but more than pistachios, peanuts or tomatoes. Overall, beer is one of the products with the lowest levels of total resveratrol (μg/L), and despite its high consumption it should not be considered as a representative source of resveratrol.

  20. Amberlite XAD-4 functionalized with succinic acid for the solid phase extractive preconcentration and separation of uranium(VI).

    Science.gov (United States)

    Metilda, P; Sanghamitra, K; Mary Gladis, J; Naidu, G R K; Prasada Rao, T

    2005-01-15

    Amberlite XAD-4 resin has been functionalized with succinic acid by coupling it with dibromosuccinic acid after acetylation. The resulting resin has been characterized by FT-IR, elemental analysis and TGA and has been used for preconcentrative separation of uranium(VI) from host of other inorganic species prior to its determination by spectrophotometry. The optimum pH value for quantitative sorption of uranium(VI) in both batch and column modes is 4.5-8.0 and desorption can be achieved by using 5.0ml of 1.0moll(-1) HCl. The sorption capacity of functionalized resin is 12.3mgg(-1). Calibration graphs were rectilinear over the uranium(VI) concentrations in the range 5-200mugl(-1). Five replicate determinations of 50mug of uranium(VI) present in 1000ml of solution gave a mean absorbance of 0.10 with a relative standard deviation of 2.56%. The detection limit corresponding to three times the standard deviation of the blank was found to be 2mugl(-1). Various cationic and anionic species at 200-fold amounts do not interfere during the preconcentration of 5.0mug of uranium(VI) present in 1000ml (batch) or 100ml (column) of sample solution. Further, adsorption kinetic and isotherm studies were also carried out by a batch method to understand the nature of sorption of uranium(VI) with the succinic acid functionalized resin. The accuracy of the developed solid phase extractive preconcentration method in conjunction with Arsenazo III procedure was tested by analyzing marine sediment (MESS-3) and soil (IAEA soil-7) reference material. Further, the above procedure has been successfully employed for the analysis of soil and sediment samples.

  1. Recovery evaluation of organophosphorus pesticides from bee pollen by matrix solid-phase dispersion extraction using sorbents based on silica and titania

    Science.gov (United States)

    Torres-Perea, C.; Muñoz-Rodríguez, D.; Medina-Peralta, S.; Carrera-Figueiras, C.; Moguel-Ordóñez, Y. B.

    2013-06-01

    This work focused on the evaluation of the recovery of organophosphorus pesticides from bee pollen after matrix solid phase-dispersion extraction (MSPD). Materials based on silica, titania and titania modified with polivylnylimidazole or polyestirene were used as adsorbents for the extraction of pesticides. Small amounts of fortified pollen (0.1 g, at 1 micro-g/g of pesticides), adsorbent (0.4 g) and solvent elution (1 mL de acetonitrile - ACN) were used in the extractions. For recovery evaluation, pollen extracts were analyzed by gas chromatography coupled with mass spectrometry.

  2. Solid phase extraction of Cu2+, Ni2+, and Co2+ ions by a new magnetic nano-composite: excellent reactivity combined with facile extraction and determination.

    Science.gov (United States)

    Azizi, Parastou; Golshekan, Mostafa; Shariati, Shahab; Rahchamani, Jalal

    2015-04-01

    In the present study, silica magnetite mesoporous nanoparticles functionalized with a new chelating agent were synthesized and introduced as a magnetic solid phase for preconcentration of trace amounts of Cu2+, Ni2+, and Co2+ ions from aqueous solutions. Briefly, MCM-41 mesoporous-coated magnetite nano-particles (MMNPs) with particle size lower than 15 nm were synthesized via chemical co-precipitation methods. Then, N-(4-methoxysalicylidene)-4,5-dinitro-1,2-phenylenediamine (HL) as a new chelating agent was synthesized and used for surface modification of mesoporous magnetic solid phase by dispersive liquid-liquid functionalization (DLLF) as a new rapid method to form HL functionalized mesoporous magnetite nanoparticles (MMNPs─HL). The structure and morphology of prepared sorbent were characterized by FT-IR, XRD, VSM, and TEM. Finally, the prepared nanoparticles were utilized for preconcentration of Cu2+, Ni2+, and Co2+ ions prior to determination by atomic absorption spectrophotometery. The calibration graph was obtained under the optimized conditions with linear dynamic range of 1.0-300 μg L(-1) and correlation coefficient (r2) of 0.998. The detection limits of this method for cobalt, nickel, and copper ions were 0.03, 0.03, and 0.04 ng/mL, respectively. Finally, the method was successfully applied to the extraction and determination of the analyte ions in natural waters and reference plant samples.

  3. A novel magnetic poly(aniline-naphthylamine)-based nanocomposite for micro solid phase extraction of rhodamine B

    Energy Technology Data Exchange (ETDEWEB)

    Bagheri, Habib, E-mail: bagheri@sharif.edu; Daliri, Rasoul; Roostaie, Ali

    2013-09-10

    Graphical abstract: -- Highlights: •A Fe{sub 3}O{sub 4}–aniline-naphthylamine nanocomposite was prepared via a simple route. •The magnetic nanocomposite was applied for isolation of RhB from water. •The nanocomposite applicability was compared with other pristine polymers. •The method was applied for the determination of RhB in different samples. -- Abstract: A novel Fe{sub 3}O{sub 4}–poly(aniline-naphthylamine)-based nanocomposite was synthesized by chemical oxidative polymerization process as a magnetic sorbent for micro solid phase extraction. The scanning electron microscopy images of the synthesized nanocomposite revealed that the copolymer posses a porous structure with diameters less than 50 nm. The extraction efficiency of this sorbent was examined by isolation of rhodamine B, a mutagenic and carcinogenic dye, from aquatic media in dispersion mode. Among different synthesized polymers, Fe{sub 3}O{sub 4}/poly(aniline-naphthylamine) nanocomposite showed a prominent efficiency. Parameters including the desorption solvent, amount of sorbent, desorption time, sample pH, ionic strength, extraction time and stirring rate were optimized. Under the optimum condition, a linear spiked calibration curve in the range of 0.35–5.00 μg L{sup −1} with R{sup 2} = 0.9991 was obtained. The limits of detection (3S{sub b}) and limits of quantification (10S{sub b}) of the method were 0.10 μg L{sup −1} and 0.35 μg L{sup −1} (n = 3), respectively. The relative standard deviation for water sample with 0.5 μg L{sup −1} of RhB was 4.2% (n = 5) and the absolute recovery was 92%. The method was applied for the determination of rhodamine B in dishwashing foam, dishwashing liquid, shampoo, pencil, matches tips and eye shadows samples and the relative recovery percentage were in the range of 94–99%.

  4. Rapid determination of 54 pharmaceutical and personal care products in fish samples using microwave-assisted extraction-Hollow fiber-Liquid/solid phase microextraction.

    Science.gov (United States)

    Zhang, Yi; Guo, Wen; Yue, Zhenfeng; Lin, Li; Zhao, Fengjuan; Chen, Peijin; Wu, Weidong; Zhu, Hong; Yang, Bo; Kuang, Yanyun; Wang, Jiong

    2017-04-15

    In this paper, a simple, rapid, solvent-less and environmental friendliness microextraction method, microwave-assisted extraction-hollow fiber-liquid/solid phase microextraction (MAE-HF-L/SME), was developed for simultaneous extraction and enrichment of 54 trace hydrophilic/lipophilic pharmaceutical and personal care products (PPCPs) from fish samples. A solid-phase extraction material, solid-phase microextraction (SPME) fiber, was synthesized. The SPME fiber had a homogeneous, loose structure and good mechanical properties, and they exhibited a good adsorption capacity for most PPCPs selected. The material formed the basis for the method of MAE-HF-L/SME. A method of liquid chromatography-high resolution mass spectroscopy (LC-HRMS) for analysis of 54 PPCPs. Under optimal synthesis and extraction conditions, the limits of detection (LODs, n=3) and the limits of quantitation (LOQs, n=10) for the 54 PPCPs were between 0.01-0.50μg·kg(-1) and 0.052.00μg·kg(-1), respectively. Percent recoveries and the relative standard deviations (RSDs) in spiked fish samples (n=6) were between 56.3%-119.9% and 0.3%-17.1%, respectively. The microextraction process of 54 PPCPs in MAE-HF-L/SME took approximately 12min. The method has a low matrix interference and high enrichment factor and may be applicable for determination of 54 different PPCPs in fish samples. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Online solid-phase extraction with high-performance liquid chromatography and mass spectrometry for the determination of five tannins in traditional Chinese medicine injections.

    Science.gov (United States)

    Sun, Meng; Lin, Yuanyuan; Zhang, Jie; Zheng, Shaohua; Wang, Sicen

    2016-03-01

    A rapid analytical method based on online solid-phase extraction with high-performance liquid chromatography and mass spectrometry has been established and applied to the determination of tannin compounds that may cause adverse effects in traditional Chinese medicine injections. Different solid-phase extraction sorbents have been compared and the elution buffer was optimized. The performance of the method was verified by evaluation of recovery (≥40%), repeatability (RSD ≤ 6%), linearity (r(2) ≥ 0.993), and limit of quantification (≤0.35 μg/mL). Five tannin compounds, gallic acid, cianidanol, gallocatechin gallate, ellagic acid, and penta-O-galloylglucose, were identified with concentrations ranging from 3.1-37.4 μg/mL in the analyzed traditional Chinese medicine injections.

  6. Simultaneous determination of 16 polycyclic aromatic hydrocarbons in reclaimed water using solid-phase extraction followed by ultra-performance convergence chromatography with photodiode array detection.

    Science.gov (United States)

    Zhang, Yun; Xiao, Zhiyong; Lv, Surong; Du, Zhenxia; Liu, Xiaoxia

    2016-03-01

    A new fast and effective analysis method has been developed to simultaneously determine 16 polycyclic aromatic hydrocarbons in reclaimed water samples by ultra-performance convergence chromatography with photodiode array detection and solid-phase extraction. The parameters of ultra-performance convergence chromatography on the separation behaviors and the crucial condition of solid-phase extraction were investigated systematically. Under optimal conditions, the 16 polycyclic aromatic hydrocarbons could be separated within 4 min. The limits of detection and quantification were in the range of 0.4-4 and 1-10 μg/L in water, respectively. This approach has been applied to a real industrial wastewater treatment plant successfully. The results showed that polycyclic aromatic hydrocarbons were dramatically decreased after chemical treatment procedure, and the oxidation procedure was effective to remove trace polycyclic aromatic hydrocarbons.

  7. Nanostructured conducting molecularly imprinted polymer for selective extraction of salicylate from urine and serum samples by electrochemically controlled solid-phase micro-extraction

    Energy Technology Data Exchange (ETDEWEB)

    Ameli, Akram [Department of Chemistry, Faculty of Science, Tarbiat Modares University, P.O. Box 14115-175, Tehran (Iran, Islamic Republic of); Alizadeh, Naader, E-mail: alizaden@modares.ac.ir [Department of Chemistry, Faculty of Science, Tarbiat Modares University, P.O. Box 14115-175, Tehran (Iran, Islamic Republic of)

    2011-11-30

    Highlights: Black-Right-Pointing-Pointer Overoxidized polypyrrole templated with salicylate has been utilized as conducting molecular imprinted polymer for EC-SPME. Black-Right-Pointing-Pointer This first study reported on conducting molecular imprinted polymer was used to EC-SPME of salicylate. Black-Right-Pointing-Pointer Proposed method, is particularly effective in sample clean-up and selective monitoring of salicylate in physiological samples. - Abstract: Overoxidized polypyrrole (OPPy) films templated with salicylate (SA) have been utilized as conducting molecular imprinted polymers (CMIPs) for potential-induced selective solid-phase micro-extraction processes. Various important fabrication factors for controlling the performance of the OPPy films have been investigated using fluorescence spectrometry. Several key parameters such as applied potential for uptake, release, pH of uptake and release solution were varied to achieve the optimum micro-extraction procedure. The film template with SA exhibited excellent selectivity over some interference. The calibration graphs were linear in the ranges of 5 Multiplication-Sign 10{sup -8} to 5 Multiplication-Sign 10{sup -4} and 1.2 Multiplication-Sign 10{sup -6} to 5 Multiplication-Sign 10{sup -4} mol mL{sup -1} and the detection limit was 4 Multiplication-Sign 10{sup -8} mol L{sup -1}. The OPPy film as the solid-phase micro-extraction absorbent has been applied for the selective clean-up and quantification of trace amounts of SA from physiological samples. The results of scanning electron microscopy (SEM) have confirmed the nano-structure morphologies of the films.

  8. Carbon coated magnetic nanoparticles as a novel magnetic solid phase extraction adsorbent for simultaneous extraction of methamphetamine and ephedrine from urine samples.

    Science.gov (United States)

    Taghvimi, Arezou; Hamishehkar, Hamed

    2017-01-15

    This paper develops a highly selective, specific and efficient method for simultaneous determination of ephedrine and methamphetamine by a new carbon coated magnetic nanoparticles (C/MNPs) as a magnetic solid phase extraction (MSPE) adsorbent in biological urine medium. The characterization of synthesized magnetic nano adsorbent was completely carried out by various characterization techniques like Fourier transform infrared (FT-IR) spectroscopy, powder x-ray diffraction (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). Nine important parameters influencing extraction efficiency including amount of adsorbent, amounts of sample volume, pH, type and amount of extraction organic solvent, time of extraction and desorption, agitation rate and ionic strength of extraction medium, were studied and optimized. Under optimized extraction conditions, a good linearity was observed in the concentration range of 100-2000ng/mL for ephedrine and 100-2500ng/mL for methamphetamine. Analysis of positive urine samples was carried out by proposed method with the recovery of 98.71 and 97.87% for ephedrine and methamphetamine, respectively. The results indicated that carbon coated magnetic nanoparticles could be applied in clinical and forensic laboratories for simultaneous determination of abused drugs in urine media.

  9. Comparison of solid phase extraction, saponification and gel permeation chromatography for the clean-up of microwave-assisted biological extracts in the analysis of polycyclic aromatic hydrocarbons.

    Science.gov (United States)

    Navarro, P; Cortazar, E; Bartolomé, L; Deusto, M; Raposo, J C; Zuloaga, O; Arana, G; Etxebarria, N

    2006-09-22

    The feasibility of different clean-up procedures was studied for the determination of polycyclic aromatic hydrocarbons (PAHs) in biota samples such as oysters, mussels and fish liver. In this sense, once the samples were extracted--essentially with acetone and in a microwave system--and before they could be analysed by gas chromatography-mass spectrometry (GC-MS), three different approaches were studied for the clean-up step: solid phase extraction (SPE), microwave-assisted saponification (MAS) and gel permeation chromatography (GPC). The main aim of this work was to maximise the recoveries of PAHs and to minimise the presence of interfering compounds in the last extract. In the case of SPE, Florisil cartridges of 1, 2 and 5 g, and silica cartridges of 5 g were studied. In that case, and with oysters and mussels, microwave-assisted extraction and 5 g Florisil cartridges provided good results. In addition, the concentrations obtained for Standard Reference Material (SRM) NIST 2977 (mussel tissue) were in good agreement with the certified values. In the case of microwave-assisted saponification, the extracts were not as clean as those obtained with 5 g Florisil and this fact lead to overestimate the concentration of the heaviest PAHs. Finally, the cleanest extracts were obtained by GPC. The method was successfully applied to mussels, oysters and hake liver, and the results obtained for NIST 2977 (mussel tissue) were within the confidence interval of the certified reference material for most of the certified analytes.

  10. Accelerated solvent extraction combined with solid phase extraction for the determination of organophosphate esters from sewage sludge compost by UHPLC-MS/MS.

    Science.gov (United States)

    Pang, Long; Yang, Peijie; Ge, Liming; Du, Jingjing; Zhang, Hongzhong

    2017-02-01

    Organophosphate esters (OPEs), widely used as flame retardants and plasticizers, are regarded as emerging pollutants. OPEs are prone to concentrate into residual activated sludge, which might cause secondary pollution if not suitably treated. Composting is an economical and effective approach to make sewage sludge stable and harmless. Therefore, it is essential to develop a novel method for analyzing OPEs in sewage sludge compost samples. However, in the composting process, large amounts of amendments are doped into the sludge to adjust the carbon-nitrogen ratio. Amendment has a strong capacity for adsorption and thus induces a decrease of extraction efficiency. This study developed a novel procedure for determining OPEs in compost samples. Accelerated solvent extraction (ASE) and solid phase extraction (SPE) were used for extracting and concentrating the OPEs from sewage sludge compost samples, and then analyzed by UHPLC-MS/MS. Some parameters were optimized in this study, mainly including the extraction solvent type, extraction temperature, static extraction time, extraction cycles, and flush volume. Under the optimal conditions, the proposed method showed good linearity between 0.50 and 100 μg kg(-1) with regression coefficients in the range of 0.9984-0.9998. Detection limits were in the range of 0.02-3 μg kg(-1) with standard deviations ranging from 2 to 6%. Acceptable recoveries between 56 and 119% for samples spiked at different concentration levels were achieved. In contrast, the recoveries merely ranged from 24 to 58% by using ultrasonic-assisted extraction. Graphical abstract A comparison of recoveries between ultrasonic-assisted extraction (UAS) and accelerated solvent extraction (ASE) for organophosphate esters from sewage sludge compost samples.

  11. An absorbing microwave micro-solid-phase extraction device used in non-polar solvent microwave-assisted extraction for the determination of organophosphorus pesticides

    Energy Technology Data Exchange (ETDEWEB)

    Wang Ziming, E-mail: wangziming@jlu.edu.cn [College of Chemistry, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); College of Environment and Resources, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Zhao Xin; Xu Xu; Wu Lijie; Su Rui; Zhao Yajing; Jiang Chengfei; Zhang Hanqi [College of Chemistry, Jilin University, 2699 Qianjin Street, Changchun 130012 (China); Ma Qiang [Chinese Academy of Inspection and Quarantine, Beijing 100123 (China); Lu Chunmei [College of Technology Center, Jilin Entry-Exit Inspection and Quarantine Bureau, Changchun 130062 (China); Dong Deming [College of Environment and Resources, Jilin University, 2699 Qianjin Street, Changchun 130012 (China)

    2013-01-14

    Highlights: Black-Right-Pointing-Pointer An absorbing microwave {mu}-SPE device packed with activated carbon was used. Black-Right-Pointing-Pointer Absorbing microwave {mu}-SPE device was made and used to enrich the analytes. Black-Right-Pointing-Pointer Absorbing microwave {mu}-SPE device was made and used to heat samples directly. Black-Right-Pointing-Pointer MAE-{mu}-SPE was applied to the extraction of OPPs with non-polar solvent only. - Abstract: A single-step extraction-cleanup method, including microwave-assisted extraction (MAE) and micro-solid-phase extraction ({mu}-SPE), was developed for the extraction of ten organophosphorus pesticides in vegetable and fruit samples. Without adding any polar solvent, only one kind of non-polar solvent (hexane) was used as extraction solvent in the whole extraction step. Absorbing microwave {mu}-SPE device, was prepared by packing activated carbon with microporous polypropylene membrane envelope, and used as not only the sorbent in {mu}-SPE, but also the microwave absorption medium. Some experimental parameters effecting on extraction efficiency was investigated and optimized. 1.0 g of sample, 8 mL of hexane and three absorbing microwave {mu}-SPE devices were added in the microwave extraction vessel, the extraction was carried out under 400 W irradiation power at 60 Degree-Sign C for 10 min. The extracts obtained by MAE-{mu}-SPE were directly analyzed by GC-MS without any clean-up process. The recoveries were in the range of 93.5-104.6%, and the relative standard deviations were lower than 8.7%.

  12. Simultaneous analysis of cortisol and cortisone in saliva using XLC-MS/MS for fully automated online solid phase extraction.

    Science.gov (United States)

    Jones, Rachel L; Owen, Laura J; Adaway, Joanne E; Keevil, Brian G

    2012-01-15

    Salivary cortisol measurements are increasingly being used in the investigation of disorders of the hypothalamic-pituitary-adrenal axis. In the salivary gland, cortisol is metabolised to cortisone by the action of 11β-hydroxysteroid dehydrogenase type 2, and cortisone is partly responsible for the variable interference observed in current salivary cortisol immunoassays. The aim of this study was to validate an assay for the simultaneous analysis of salivary cortisol and cortisone using the Spark Holland Symbiosis™ in eXtraction liquid chromatography-tandem mass spectrometry (XLC-MS/MS) mode for fully automated online solid phase extraction (SPE). Saliva samples were diluted in water with the addition of internal standard (d4-cortisol and d7-cortisone). Online SPE was performed using the Spark Holland Symbiosis™ with HySphere™ C18 SPE cartridges and compounds were eluted onto a Phenomenex® C18 guard column attached to a Phenomenex® Onyx monolithic C18 column for chromatography. Mass spectrometry used the Waters® Xevo™ TQ MS in electrospray positive mode. Cortisol and cortisone eluted with their internal standards at 1.95 and 2.17 min, respectively, with a total run time of four minutes. No evidence of ion-suppression was observed. The assay was linear up to 3393 nmol/L for cortisol and 3676 nmol/L for cortisone, with lower limits of quantitation of 0.75 nmol/L and 0.50 nmol/L, respectively. Intra- and inter-assay imprecision was cortisone across three levels of internal quality control, with accuracy and recovery within accepted limits. High specificity was demonstrated following interference studies which assessed 29 structurally-related steroids at supra-physiological concentrations. We have successfully validated an assay for the simultaneous analysis of salivary cortisol and cortisone using XLC-MS/MS and fully automated online SPE. The assay benefits from increased specificity compared to immunoassay and minimal sample preparation which allows high

  13. Design of a new cartridge for selective solid phase extraction using molecularly imprinted polymers: selective extraction of theophylline from human serum samples.

    Science.gov (United States)

    Khorrami, Afshin Rajabi; Rashidpur, Amene

    2009-11-15

    This paper describes design of a new cartridge for selective solid phase extraction (SPE) using molecularly imprinted polymers (MIPs). The apparatus which is termed solvent extraction-MISPE (SE-MISPE) cartridge, consisted of a modified conventional micro test tube and has been developed to perform simultaneous forward-extraction of analyte from aqueous sample solution to an organic phase and back-extraction to MIP solid phase. In order to evaluate the performance of the proposed method, extraction of theophylline (THP) from human serum sample was investigated. An appropriate amount of THP-imprinted polymer was placed in the bottom of the micro tube and an organic solvent pipetted onto it and left to swell the polymer completely. A polyethylene frit to secure MIP particles was positioned by two Teflon rings such that it was fixed below the level of the organic layer. Then, aqueous sample solution containing THP was layered over the organic phase and the lid was closed. After completion of extraction, the organic and aqueous phases were removed and the adsorbed analyte was desorbed using a polar organic solvent. In order to reach the highest recovery, the experimental parameters such as the type of organic solvent, pH and ionic strength of aqueous phase, organic to aqueous volume ratio, time of extraction, type and amount of desorbent solvent were optimized. Under the experimental conditions, a plot of HPLC peak areas vs. initial concentrations of THP in the concentration interval of 0.5-30 microg ml(-1) showed a good linearity (r=0.9974). The limit of detection (LOD) and limit of quantification (LOQ) based on three and ten times of the noise of HPLC profile were 0.09 and 0.3 microg ml(-1), respectively. The relative standard deviation (RSD) of the proposed method for the extraction and determination of 5 microg THP from 200 microl standard sample solution for 3 replicate measurements was 3.5%. The results showed that by means of the proposed cartridge, THP could

  14. Analysis of lignans in Magnoliae Flos by turbulent flow chromatography with online solid-phase extraction and high-performance liquid chromatography with tandem mass spectrometry.

    Science.gov (United States)

    Zhou, Xuan; Chen, Cen; Ye, Xiaolan; Song, Fenyun; Fan, Guorong; Wu, Fuhai

    2016-04-01

    In this study, a method coupling turbulent flow chromatography with online solid-phase extraction and high-performance liquid chromatography with tandem mass spectrometry was developed for analyzing the lignans in Magnoliae Flos. By the online pretreatment of turbulent flow chromatography solid-phase extraction, the impurities removal and analytes concentration were automatically processed, and the lignans were separated rapidly and well. Seven lignans of Magnoliae Flos including epieudesmin, magnolin, 1-irioresinol-B-dimethyl ether, epi-magnolin, fargesin aschantin, and demethoxyaschantin were identified by comparing their retention behavior, UV spectra, and mass spectra with those of reference substances or literature data. The developed method was validated, and the good results showed that the method was not only automatic and rapid, but also accurate and reliable. The turbulent flow chromatography with online solid-phase extraction and high-performance liquid chromatography with tandem mass spectrometry method holds a high potential to become an effective method for the quality control of lignans in Magnoliae Flos and a useful tool for the analysis of other complex mixtures.

  15. Phenylboronic acid modified solid-phase extraction column: Preparation, characterization, and application to the analysis of amino acids in sepia capsule by removing the maltose.

    Science.gov (United States)

    Guo, Mengzhe; Yin, Dengyang; Han, Jie; Zhang, Liyan; Li, Xiao; He, Dandan; Du, Yan; Tang, Daoquan

    2016-09-01

    Maltose, a common auxiliary material of pharmaceutical preparation, may disturb the analysis of total amino acids in sepia capsule by aldolization. Therefore, it is necessary to remove the maltose through a convenient method. In this work, a phenylboronic acid modified solid-phase extraction column has been synthesized and used to remove the maltose. The materials were synthesized by one step "thiol-ene" reaction and the parameters of the column such as absorption capacity, recovery, and absorption specificity have been investigated. The results showed the column (0.5 cm of length × 0.5 cm of inner diameter) can absorb 4.6 mg maltose with a linear absorption and absorption specificity. Then this technique was applied in the quantification of amino acids in sepia capsule. After the optimization of the method, four kinds of amino acids, which were the most abundant, were quantified by high-performance liquid chromatography with diode array detection. The amounts of the four kinds of amino acids are 1.5∼2 times more than that without the treatment of solid-phase extraction column, which almost overcomes the influence of the maltose. All the results indicate that the phenylboronic acid modified solid-phase extraction column can successfully help to accurately quantify the total amino acids in sepia capsule.

  16. Analyses of nitrobenzene,benzene and aniline in environmental water samples by headspace solid phase micro-extraction coupled with gas chromatography-mass spectrometry

    Institute of Scientific and Technical Information of China (English)

    CHEN Ming; YIN Yongguang; TAI Chao; ZHANG Qinghua; LIU Jiyan; HU Jingtian; JIANG Guibin

    2006-01-01

    A headspace solid phase microextraction coupled with gas chromatography mass spectrometry (HS-SPME/GC-MS) method was established for analyzing nitrobenzene, benzene and aniline in environmental water samples simultaneously.Factors affecting extraction efficiency (SPME fiber selection, acidity, temperature, salt addition, extraction time, headspace, etc) were verified. Under optimal extraction conditions, the detection limits are 0.50, 0.11 and 1.00 μg/L for nitrobenzene, benzene and aniline, respectively. The results indicate that this method is capable of making sensitive and accuracy analyses on nitrobenzene, benzene and aniline in environmental water samples.

  17. Pressurized liquid extraction using water/isopropanol coupled with solid-phase extraction cleanup for industrial and anthropogenic waste-indicator compounds in sediment

    Science.gov (United States)

    Burkhardt, M.R.; ReVello, R.C.; Smith, S.G.; Zaugg, S.D.

    2005-01-01

    A broad range of organic compounds is recognized as environmentally relevant for their potential adverse effects on human and ecosystem health. This method was developed to better determine the distribution of 61 compounds that are typically associated with industrial and household waste as well as some that are toxic and known (or suspected) for endocrine-disrupting potential extracted from environmental sediment samples. Pressurized liquid extraction (PLE) coupled with solid-phase extraction (SPE) was used to reduce sample preparation time, reduce solvent consumption to one-fifth of that required using dichloromethane-based Soxhlet extraction, and to minimize background interferences for full scan GC/MS analysis. Recoveries from spiked Ottawa sand, commercially available topsoil, and environmental stream sediment, fortified at 4-720 ??g per compound, averaged 76 ?? 13%. Initial method detection limits for single-component compounds ranged from 12.5 to 520 ??g/kg, based on 25 g samples. Results from 103 environmental sediment samples show that 36 out of 61 compounds (59%) were detected in at least one sample with concentrations ranging from 20 to 100,000 ??g/kg. The most frequently detected compound, beta-sitosterol, a plant sterol, was detected in 87 of the 103 (84.5%) environmental samples with a concentration range 360-100,000 ??g/kg. Results for a standard reference material using dichloromethane Soxhlet-based extraction are also compared. ?? 2004 Published by Elsevier B.V.

  18. Optimization of pressurized liquid extraction using a multivariate chemometric approach and comparison of solid-phase extraction cleanup steps for the determination of polycyclic aromatic hydrocarbons in mosses.

    Science.gov (United States)

    Foan, L; Simon, V

    2012-09-21

    A factorial design was used to optimize the extraction of polycyclic aromatic hydrocarbons (PAHs) from mosses, plants used as biomonitors of air pollution. The analytical procedure consists of pressurized liquid extraction (PLE) followed by solid-phase extraction (SPE) cleanup, in association with analysis by high performance liquid chromatography coupled with fluorescence detection (HPLC-FLD). For method development, homogeneous samples were prepared with large quantities of the mosses Isothecium myosuroides Brid. and Hypnum cupressiforme Hedw., collected from a Spanish Nature Reserve. A factorial design was used to identify the optimal PLE operational conditions: 2 static cycles of 5 min at 80 °C. The analytical procedure performed with PLE showed similar recoveries (∼70%) and total PAH concentrations (∼200 ng g(-1)) as found using Soxtec extraction, with the advantage of reducing solvent consumption by 3 (30 mL against 100mL per sample), and taking a fifth of the time (24 samples extracted automatically in 8h against 2 samples in 3.5h). The performance of SPE normal phases (NH(2), Florisil, silica and activated aluminium) generally used for organic matrix cleanup was also compared. Florisil appeared to be the most selective phase and ensured the highest PAH recoveries. The optimal analytical procedure was validated with a reference material and applied to moss samples from a remote Spanish site in order to determine spatial and inter-species variability.

  19. Preparation of magnetic chitosan and graphene oxide-functional guanidinium ionic liquid composite for the solid-phase extraction of protein

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Xueqin; Wang, Yuzhi, E-mail: wyzss@hnu.edu.cn; Wang, Ying; Pan, Qi; Chen, Jing; Huang, Yanhua; Xu, Kaijia

    2015-02-25

    Highlights: • A strategy for the solid-phase extraction of protein based on magnetic chitosan and graphene oxide-functional guanidinium ionic liquids. • Trypsin, lysozyme, ovalbumin and bovine serum albumin were used as the analyst. • The possibility of reusability and regeneration has been evaluated. - Abstract: A series of novel cationic functional hexaalkylguanidinium ionic liquids and anionic functional tetraalkylguanidinium ionic liquids have been synthesized, and then magnetic chitosan graphene oxide (MCGO) composite has been prepared and coated with these functional guanidinium ionic liquids to extract protein by magnetic solid-phase extraction. MCGO-functional guanidinium ionic liquid has been characterized by vibrating sample magnetometer, field emission scanning electron microscopy, X-ray diffraction spectrometer and Fourier transform infrared spectrometer. After extraction, the concentrations of protein were determined by measuring the absorbance at 278 nm using an ultra violet visible spectrophotometer. The advantages of MCGO-functional guanidinium ionic liquid in protein extraction were compared with magnetic chitosan, graphene oxide, MCGO and MCGO-ordinary imidazolium ionic liquid. The proposed method has been applied to extract trypsin, lysozyme, ovalbumin and bovine serum albumin. A comprehensive study of the adsorption conditions such as the concentration of protein, the amount of MCGO-functional guanidinium ionic liquid, the pH, the temperature and the extraction time were also presented. Moreover, the MCGO-functional guanidinium ionic liquid can be easily regenerated, and the extraction capacity was about 94% of the initial one after being used three times.

  20. Multivariate analysis of the volatile components in tobacco based on infrared-assisted extraction coupled to headspace solid-phase microextraction and gas chromatography-mass spectrometry.

    Science.gov (United States)

    Yang, Yanqin; Pan, Yuanjiang; Zhou, Guojun; Chu, Guohai; Jiang, Jian; Yuan, Kailong; Xia, Qian; Cheng, Changhe

    2016-11-01

    A novel infrared-assisted extraction coupled to headspace solid-phase microextraction followed by gas chromatography with mass spectrometry method has been developed for the rapid determination of the volatile components in tobacco. The optimal extraction conditions for maximizing the extraction efficiency were as follows: 65 μm polydimethylsiloxane-divinylbenzene fiber, extraction time of 20 min, infrared power of 175 W, and distance between the infrared lamp and the headspace vial of 2 cm. Under the optimum conditions, 50 components were found to exist in all ten tobacco samples from different geographical origins. Compared with conventional water-bath heating and nonheating extraction methods, the extraction efficiency of infrared-assisted extraction was greatly improved. Furthermore, multivariate analysis including principal component analysis, hierarchical cluster analysis, and similarity analysis were performed to evaluate the chemical information of these samples and divided them into three classifications, including rich, moderate, and fresh flavors. The above-mentioned classification results were consistent with the sensory evaluation, which was pivotal and meaningful for tobacco discrimination. As a simple, fast, cost-effective, and highly efficient method, the infrared-assisted extraction coupled to headspace solid-phase microextraction technique is powerful and promising for distinguishing the geographical origins of the tobacco samples coupled to suitable chemometrics.

  1. Dispersive solid-phase extraction as a simplified clean-up technique for biological sample extracts. Determination of polybrominated diphenyl ethers by gas chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Fontana, Ariel R; Camargo, Alejandra; Martinez, Luis D; Altamirano, Jorgelina C

    2011-05-06

    Dispersive solid-phase extraction (DSPE) is proposed for the first time as a simplified, fast and low cost clean-up technique of biological sample extracts for polybrominated diphenyl ethers (PBDEs) determination. The combination of a traditional extraction technique, such as ultrasound-assisted leaching (USAL) with DSPE was successfully applied for sample preparation prior to gas chromatography-tandem mass spectrometry (GC-MS/MS) analysis. The analytes were first extracted from 1g homogenized sample in n-hexane:dichloromethane (8:2) by applying USAL technique and further cleaned-up using DSPE with 0.20 g C(18)-silica as sorbent material. Different solvent mixtures, sorbent type and amount, and lipid digestion procedures were evaluated in terms of clean-up and extraction efficiency. Under optimum conditions, the method detection limits (MDLs) for PBDEs, calculated as three times the signal-to-noise ratio (S/N) were within the range 9-44 pg g(-1) wet weight. The calibration graphs were linear within the concentration range of 53-500,000 pg g(-1), 66-500,000 pg g(-1), 89-500,000 pg g(-1) and 151-500,000 pg g(-1) for BDE-47, BDE-100, BDE-99 and BDE-153, respectively; and the coefficient of determination (r(2)) exceeded 0.9992 for all analytes. The proposed methodology was compared with a reference solid-phase extraction technique. The applicability of the methodology for the screening of PBDEs has been demonstrated by analyzing spiked and real samples of biological nature (fish, egg and chicken) with different lipid content as well as reference material (WELL-WMF-01). Recovery values ranged between 75% and 114% and the measured concentrations in certified material showed a reasonable agreement with the certified ones. BDE-47, BDE-100 and BDE-99 were quantified in three of the seven analyzed samples and the concentrations ranged between 91 and 140 pg g(-1). In addition, this work is the first description of PBDEs detected in fish of Argentinean environment.

  2. Development of colorimetric solid Phase Extraction (C-SPE) for in-flight Monitoring of spacecraft Water Supplies

    Energy Technology Data Exchange (ETDEWEB)

    Daniel Bryan Gazda

    2004-12-19

    Although having recently been extremely successful gathering data on the surface of Mars, robotic missions are not an effective substitute for the insight and knowledge about our solar system that can be gained though first-hand exploration. Earlier this year, President Bush presented a ''new course'' for the U.S. space program that shifts NASA's focus to the development of new manned space vehicles to the return of humans to the moon. Re-establishing the human presence on the moon will eventually lead to humans permanently living and working in space and also serve as a possible launch point for missions into deeper space. There are several obstacles to the realization of these goals, most notably the lack of life support and environmental regeneration and monitoring hardware capable of functioning on long duration spaceflight. In the case of the latter, past experience on the International Space Station (ISS), Mir, and the Space Shuttle has strongly underscored the need to develop broad spectrum in-flight chemical sensors that: (1) meet current environmental monitoring requirements on ISS as well as projected requirements for future missions, and (2) enable the in-situ acquisition and analysis of analytical data in order to further define on-orbit monitoring requirements. Additionally, systems must be designed to account for factors unique to on-orbit deployment such as crew time availability, payload restrictions, material consumption, and effective operation in microgravity. This dissertation focuses on the development, ground testing, and microgravity flight demonstration of Colorimetric Solid Phase Extraction (C-SPE) as a candidate technology to meet the near- and long-term water quality monitoring needs of NASA. The introduction will elaborate further on the operational and design requirements for on-orbit water quality monitoring systems by discussing some of the characteristics of an ''ideal'' system. A

  3. Development of colorimetric solid Phase Extraction (C-SPE) for in-flight Monitoring of spacecraft Water Supplies

    Energy Technology Data Exchange (ETDEWEB)

    Gazda, Daniel Bryan [Iowa State Univ., Ames, IA (United States)

    2004-01-01

    Although having recently been extremely successful gathering data on the surface of Mars, robotic missions are not an effective substitute for the insight and knowledge about our solar system that can be gained though first-hand exploration. Earlier this year, President Bush presented a ''new course'' for the U.S. space program that shifts NASA's focus to the development of new manned space vehicles to the return of humans to the moon. Re-establishing the human presence on the moon will eventually lead to humans permanently living and working in space and also serve as a possible launch point for missions into deeper space. There are several obstacles to the realization of these goals, most notably the lack of life support and environmental regeneration and monitoring hardware capable of functioning on long duration spaceflight. In the case of the latter, past experience on the International Space Station (ISS), Mir, and the Space Shuttle has strongly underscored the need to develop broad spectrum in-flight chemical sensors that: (1) meet current environmental monitoring requirements on ISS as well as projected requirements for future missions, and (2) enable the in-situ acquisition and analysis of analytical data in order to further define on-orbit monitoring requirements. Additionally, systems must be designed to account for factors unique to on-orbit deployment such as crew time availability, payload restrictions, material consumption, and effective operation in microgravity. This dissertation focuses on the development, ground testing, and microgravity flight demonstration of Colorimetric Solid Phase Extraction (C-SPE) as a candidate technology to meet the near- and long-term water quality monitoring needs of NASA. The introduction will elaborate further on the operational and design requirements for on-orbit water quality monitoring systems by discussing some of the characteristics of an ''ideal'' system. A

  4. Determination of endocrine disrupting compounds in fish liver, brain, and muscle using focused ultrasound solid-liquid extraction and dispersive solid phase extraction as clean-up strategy.

    Science.gov (United States)

    Ros, Oihana; Vallejo, Asier; Olivares, Maitane; Etxebarria, Nestor; Prieto, Ailette

    2016-08-01

    This study describes a new method for the simultaneous extraction of several endocrine disrupting compounds, including alkylphenols (APs), estrogen, bisphenol-A (BPA) and one phthalate metabolite (mono-2-ethylhexyl ester, MEHP) in fish liver, brain, and muscle. Parameters affecting the extraction (extraction solvent and temperature) and the clean-up (dispersive phase nature and amount) steps were evaluated. The extraction was performed by means of focused ultrasound solid-liquid extraction (FUSLE) using 10 mL of n-hexane:acetone (50:50, v/v) for 5 min at ~0 °C, and the clean-up was done by means of dispersive solid phase extraction (dSPE) using 100 mg of ENVI-CARB and 100 mg of MgSO4 for the cleaning of brain and muscle extracts together with 100 mg of PSA in the case of liver extracts. Good apparent recoveries were obtained in the case of liver (62-132 %), brain (66-120 %), and muscle (74-129 %), relative standard deviation (RSD%) was always below 26 %, and the method detection limits (MDLs) were at low ng/g level. The developed method was applied to fish captured in Urdaibai estuary (Bay of Biscay) in December 2015, and the concentrations obtained were in the range MDL-1115 ng/g in brain, MDL-962 ng/g in muscle, and MDL-672 ng/g in liver. In general, the highest concentrations were measured in liver, followed by brain and muscle. In addition, diethylstilbestrol was only detected in fish brain. Graphical Abstract MS method scheme for the/MS method scheme for the determination of EDCs in fish liver, brain and muscle.

  5. Determination of tobramycin in soil by HPLC with ultrasonic-assisted extraction and solid-phase extraction.

    Science.gov (United States)

    He, Shun; Chen, Qiyou; Sun, Yan; Zhu, Yuncong; Luo, Laixin; Li, Jianqiang; Cao, Yongsong

    2011-04-15

    Pharmaceuticals residues in the environment have become a growing scientific interest worldwide. In the light of the possible harmful effects of tobramycin, a rapid and sensitive analytical method for determination of tobramycin in soil was developed. The extraction and purification methods, derivatization conditions, and chromatographic conditions in the determination of tobramycin in soil have been fully investigated. Extraction was carried out by a combination of vortex mixer and ultrasonic oscillation using acetone/water as the extraction agent. The extract was concentrated to 1 mL and passed through the C(18) SPE cartridge rinsed with water (3 mL), methanol (3 mL). The derivatization procedure was followed by the reaction of tobramycin with 4-Chloro-3,5-dinitrobenzotrifluoride at 60°C for 10 min in pH 9.0 H(3)BO(3)-Na(2)B(4)O(7) medium. The labeled tobramycin was determined by high performance liquid chromatography at 245 nm. Separation was accomplished within 15 min in gradient elution mode with trifluoroacetic acid in mobile phase as ion-pair reagent. The correlation coefficient for the method was 0.9999 in concentrations ranging from 0.10 to 100.0 μg/g. The limit of detection was 0.02 μg/g for tobramycin in soil at a signal-to-noise ratio of 3. The calculated recoveries of the proposed method were from 78.0 to 91.0% and RSDs were 3.38-9.79% in the application to the quantitative determination of tobramycin in all types of soil. The method will help to establish adequate monitoring of tobramycin residue in soil and make the contribution to environmental behavior evaluation.

  6. Streamlined Membrane Proteome Preparation for Shotgun Proteomics Analysis with Triton X-100 Cloud Point Extraction and Nanodiamond Solid Phase Extraction

    OpenAIRE

    Pham, Minh D.; Ting-Chun Wen; Hung-Cheng Li; Pei-Hsuan Hsieh; Yet-Ran Chen; Huan-Cheng Chang; Chau-Chung Han

    2016-01-01

    While mass spectrometry (MS) plays a key role in proteomics research, characterization of membrane proteins (MP) by MS has been a challenging task because of the presence of a host of interfering chemicals in the hydrophobic protein extraction process, and the low protease digestion efficiency. We report a sample preparation protocol, two-phase separation with Triton X-100, induced by NaCl, with coomassie blue added for visualizing the detergent-rich phase, which streamlines MP preparation fo...

  7. Solid-phase extraction using bis(indolyl)methane-modified silica reinforced with multiwalled carbon nanotubes for the simultaneous determination of flavonoids and aromatic organic acid preservatives.

    Science.gov (United States)

    Wang, Na; Liao, Yuan; Wang, Jiamin; Tang, Sheng; Shao, Shijun

    2015-12-01

    A novel bis(indolyl)methane-modified silica reinforced with multiwalled carbon nanotubes sorbent for solid-phase extraction was designed and synthesized by chemical immobilization of nitro-substituted 3,3'-bis(indolyl)methane on silica modified with multiwalled carbon nanotubes. Coupled with high-performance liquid chromatography analysis, the extraction properties of the sorbent were evaluated for flavonoids and aromatic organic acid compounds. Under optimum conditions, the sorbent can simultaneously extract five flavonoids and two aromatic organic acid preservatives in aqueous solutions in a single-step solid-phase extraction procedure. Wide linear ranges were obtained with correlation coefficients (R(2) ) ranging from 0.9843 to 0.9976, and the limits of detection were in the range of 0.5-5 μg/L for the compounds tested. Compared with the silica modified with multiwalled carbon nanotubes sorbent and the nitro-substituted 3,3'-bis(indolyl)methane-modified silica sorbent, the developed sorbent exhibited higher extraction efficiency toward the selected analytes. The synergistic effect of nitro-substituted 3,3'-bis(indolyl)methane and multiwalled carbon nanotubes not only improved the surface-to-volume ratio but also enhanced multiple intermolecular interactions, such as hydrogen bonds, π-π, and hydrophobic interactions, between the new sorbent and the selected analytes. The as-established solid-phase extraction with high-performance liquid chromatography and diode array detection method was successfully applied to the simultaneous determination of flavonoids and aromatic organic acid preservatives in grape juices with recoveries ranging from 83.9 to 112% for all the selected analytes.

  8. Molecularly imprinted polymers for on-line extraction techniques.

    Science.gov (United States)

    Moein, Mohammad M; Abdel-Rehim, Mohamed