WorldWideScience

Sample records for on-line isotope separation

  1. The Leuven isotope separator on-line laser ion source

    CERN Document Server

    Kudryavtsev, Y; Franchoo, S; Huyse, M; Gentens, J; Kruglov, K; Müller, W F; Prasad, N V S; Raabe, R; Reusen, I; Van den Bergh, P; Van Duppen, P; Van Roosbroeck, J; Vermeeren, L; Weissman, L

    2002-01-01

    An element-selective laser ion source has been used to produce beams of exotic radioactive nuclei and to study their decay properties. The operational principle of the ion source is based on selective resonant laser ionization of nuclear reaction products thermalized and neutralized in a noble gas at high pressure. The ion source has been installed at the Leuven Isotope Separator On-Line (LISOL), which is coupled on-line to the cyclotron accelerator at Louvain-la-Neuve. sup 5 sup 4 sup , sup 5 sup 5 Ni and sup 5 sup 4 sup , sup 5 sup 5 Co isotopes were produced in light-ion-induced fusion reactions. Exotic nickel, cobalt and copper nuclei were produced in proton-induced fission of sup 2 sup 3 sup 8 U. The b decay of the sup 6 sup 8 sup - sup 7 sup 4 Ni, sup 6 sup 7 sup - sup 7 sup 0 Co, sup 7 sup 0 sup - sup 7 sup 5 Cu and sup 1 sup 1 sup 0 sup - sup 1 sup 1 sup 4 Rh isotopes has been studied by means of beta-gamma and gamma-gamma spectroscopy. Recently, the laser ion source has been used to produce neutron-d...

  2. On-line separation of short-lived beryllium isotopes

    CERN Document Server

    Köster, U; Catherall, R; Fedosseev, V; Georg, U; Huber, G; Jading, Y; Jonsson, O; Koizumi, M; Kratz, K L; Kugler, E; Lettry, Jacques; Mishin, V I; Ravn, H L; Sebastian, V; Tamburella, C; Wöhr, A

    1998-01-01

    With the development of a new laser ionization scheme, it became possible to ionize beryllium efficiently in the hot cavity of the ISOLDE laser ion source. The high target and ion source temperatures enable the release of short-lived beryllium isotopes. Thus all particle-stable beryllium isotopes could be extracted from a standard uranium carbide/graphite target. For the first time the short-lived isotopes /sup 12/Be and /sup 14/Be could be identified at an ISOL facility, /sup 14/Be being among the most short-lived isotopes separated so far at ISOLDE. The release time from the UC/graphite target was studied with several beryllium isotopes. Profiting from the element selectivity of laser ionization, the strong and isotopically pure beam of /sup 12/Be allowed to determine the half- life to T/sub 1/2 /=21.34(23) ms and the probability of beta-delayed neutron emission to P/sub n/=0.48/sub -0.10//sup +0.12/(23 refs).

  3. Proceedings of the isotope separator on-line workshop

    Energy Technology Data Exchange (ETDEWEB)

    Chrien, R E [ed.

    1978-07-01

    Separate abstracts were prepared for thirteen of the papers in this volume. The remaining three have already been cited in ERA, and can be located by reference to the entry CONF-771078-- in the Report Number Index. (RWR)

  4. Application for the On-line Isotope Mass Separator ISOLDE Facility: the Mass Scan

    CERN Document Server

    Sánchez-Conejo, Jorge

    2003-01-01

    The purpose of the Mass Scan Application is to scan the mass of the ion beam that passes through the GPS (General Purpose Separator) on the On-Line Isotope Mass Separator ISOLDE facility. The application has been developed in Java, making use of the Java Development Kit 1.4 and the PS Java environment.

  5. Application for the On-line Isotope Mass Separator ISOLDE Facility: the Target Heater

    CERN Document Server

    Sánchez-Conejo, Jorge

    2003-01-01

    The purpose of the Heater Application is to heat and cool the target and line used on the On-Line Isotope Mass Separator ISOLDE facility up to a desired temperature selected by the user. The application has been developed in Java, making use of the Java Development Kit 1.4 and the PS Java environment.

  6. On-line separation of refractory hafnium and tantalum isotopes at the ISOCELE separator

    CERN Document Server

    Liang, C F; Obert, J; Paris, P; Putaux, J C

    1981-01-01

    By chemical evaporation technique, neutron deficient hafnium nuclei have been on-line separated at the ISOCELE facility, from the isobar rare-earth elements, in the metal-fluoride HfF/sub 3//sup +/ ion form. Half-lives of /sup 162-165/Hf have been measured. Similarly, tantalum has been selectively separated on the TaF/sub 4//sup +/ form. (4 refs) .

  7. Chemical investigations of isotope separation on line target units for carbon and nitrogen beams

    CERN Document Server

    Franberg, H; Gäggeler, H W; Köster, U

    2006-01-01

    Radioactive ion beams (RIBs) are of significant interest in a number of applications. Isotope separation on line (ISOL) facilities provide RIB with high beam intensities and good beam quality. An atom that is produced within the ISOL target will first diffuse out from the target material. During the effusion towards the transfer line and into the ion source the many contacts with the surrounding surfaces may cause unacceptable delays in the transport and, hence, losses of the shorter-lived isotopes. We performed systematic chemical investigations of adsorption in a temperature and concentration regime relevant for ISOL targets and ion source units, with regard to CO/sub x/ and NOmaterials are potential construction materials for the above-mentioned areas. Off-line and on-line tests have been performed using a gas thermochromatography setup with radioactive tracers. The experiments were performed at the production of tracers for atmospheric chemistry (PROTRAC) facility at the Paul Schener Institute in Villigen...

  8. Recent studies to improve release properties from thick isotope separator on-line fission targets

    CERN Document Server

    Lau, C; Verney, D; Bajeat, O; Ibrahim, F; Clapier, F; Cottereau, E; Donzaud, C; Ducourtieux, M; Essabaa, S; Guillemaud-Müller, D; Hosni, F; Lefort, H; Le Blanc, F; Müller, A C

    2003-01-01

    In the framework of the PARRNe program (Production d'Atomes Radioactifs Riches en Neutrons) of IPN Orsay, various techniques are currently used to characterize the release properties of elements of interest from a UC//X target. On-line studies have been carried out with two plasma ion sources: a Nier-Bernas and a hot plasma ISOLDE- type (the ISOLDE collaboration kindly supplied us a MK5 ion source for these studies). In parallel, the analysis of the chemical and structure properties of some UC//X samples as function of heating conditions has been carried out. Such data are essential to determine optimal conditions for the production of isotopes by the isotope separator on-line (ISOL) technique. First results are presented here for Kr and Ag. Investigations for other kinds of fission targets are planned.

  9. Recent great impact by an Isotope Separator On-Line (ISOL) in nuclear and radiochemistry.

    Science.gov (United States)

    Sakama, Minoru

    2016-01-01

    On April 9 2015, the Letter article titled "Measurement of the first ionization potential of lawrencium, element 103" is now published at News and Views on Nature (2015) which has been performed by our remarkably Japanese colleagues of nuclear and radiochemistry at JAEA (Japan Atomic Energy Agency). In this review, the author will state that the isotope separator on-line (ISOL) our regularly used, one of mass separation techniques, with a thermal surface ionization makes possible for determining the ionization potential of lawrencium based on the fruitful fundations of developing the ISOL system until now and also ever studying searches for unknown nuclei and these nuclear decay properties around actinide region in the past 20 years.

  10. Resonance ionization laser ion sources for on-line isotope separators (invited).

    Science.gov (United States)

    Marsh, B A

    2014-02-01

    A Resonance Ionization Laser Ion Source (RILIS) is today considered an essential component of the majority of Isotope Separator On Line (ISOL) facilities; there are seven laser ion sources currently operational at ISOL facilities worldwide and several more are under development. The ionization mechanism is a highly element selective multi-step resonance photo-absorption process that requires a specifically tailored laser configuration for each chemical element. For some isotopes, isomer selective ionization may even be achieved by exploiting the differences in hyperfine structures of an atomic transition for different nuclear spin states. For many radioactive ion beam experiments, laser resonance ionization is the only means of achieving an acceptable level of beam purity without compromising isotope yield. Furthermore, by performing element selection at the location of the ion source, the propagation of unwanted radioactivity downstream of the target assembly is reduced. Whilst advances in laser technology have improved the performance and reliability of laser ion sources and broadened the range of suitable commercially available laser systems, many recent developments have focused rather on the laser/atom interaction region in the quest for increased selectivity and/or improved spectral resolution. Much of the progress in this area has been achieved by decoupling the laser ionization from competing ionization processes through the use of a laser/atom interaction region that is physically separated from the target chamber. A new application of gas catcher laser ion source technology promises to expand the capabilities of projectile fragmentation facilities through the conversion of otherwise discarded reaction fragments into high-purity low-energy ion beams. A summary of recent RILIS developments and the current status of laser ion sources worldwide is presented.

  11. Status report of the Jyvaskyla ion guide isotope separator on-line facility

    NARCIS (Netherlands)

    Penttila, H; Dendooven, P; Honkanen, A; Huhta, M; Jauho, PP; Jokinen, A; Lhersonneau, G; Oinonen, M; Parmonen, JM; Perajarvi, K; Aysto, J

    1997-01-01

    The ion guide isotope separator facility IGISOL of the University of Jyvaskyla has been moved to the new K-130 heavy ion cyclotron laboratory. The totally reconstructed facility is described in detail. The primary beams and targets, helium pumping, separator beam line construction and separator beam

  12. Status report of the Jyvaeskylaeion guide isotope separator on-line facility

    Energy Technology Data Exchange (ETDEWEB)

    Penttilae, H.; Dendooven, P.; Honkanen, A.; Huhta, M.; Jauho, P.P.; Jokinen, A.; Lhersonneau, G.; Oinonen, M.; Parmonen, J.-M.; Peraejaervi, K.; Aeystoe, J. [Jyvaeskylae Univ. (Finland). Dept. of Physics

    1997-04-01

    The ion guide isotope separator facility IGISOL of the University of Jyvaeskylaehas been moved to the new K-130 heavy ion cyclotron laboratory. The totally reconstructed facility is described in detail. The primary beams and targets, helium pumping, separator beam line construction and separator beam diagnostics are discussed. The spectroscopy stations are introduced with illustrative examples from the research program, including beta-delayed proton and neutron spectroscopy, gamma-ray spectroscopy with and without arrays, conversion electron spectroscopy, collinear laser spectroscopy and nuclear level lifetime spectroscopy. (orig.). 15 refs.

  13. On-line experimental results of an argon gas cell-based laser ion source (KEK Isotope Separation System)

    Science.gov (United States)

    Hirayama, Y.; Watanabe, Y. X.; Imai, N.; Ishiyama, H.; Jeong, S. C.; Jung, H. S.; Miyatake, H.; Oyaizu, M.; Kimura, S.; Mukai, M.; Kim, Y. H.; Sonoda, T.; Wada, M.; Huyse, M.; Kudryavtsev, Yu.; Van Duppen, P.

    2016-06-01

    KEK Isotope Separation System (KISS) has been developed at RIKEN to produce neutron rich isotopes with N = 126 to study the β -decay properties for application to astrophysics. The KISS is an element-selective mass-separation system which consists of an argon gas cell-based on laser ion source for atomic number selection and an ISOL mass-separation system. The argon gas cell of KISS is a key component to stop and collect the unstable nuclei produced in a multi-nucleon transfer reaction, where the isotopes of interest will be selectively ionized using laser resonance ionization. We have performed off- and on-line experiments to study the basic properties of the gas cell as well as of the KISS. We successfully extracted the laser-ionized stable 56Fe (direct implantation of a 56Fe beam into the gas cell) atoms and 198Pt (emitted from the 198Pt target by elastic scattering with a 136Xe beam) atoms from the KISS during the commissioning on-line experiments. We furthermore extracted laser-ionized unstable 199Pt atoms and confirmed that the measured half-life was in good agreement with the reported value.

  14. The ISOLDE on-line isotope separator at the 600 MeV Synchro-Cyclotron

    CERN Multimedia

    CERN PhotoLab

    1973-01-01

    Is at present being thoroughly modified and improved, in order to allow for the increased proton beam intensities, resulting from the SC improvement programme. This photograph, taken before the dismantinling of the facility in June 1973, shows the separator analysing magnet (centre background), the collector chamber of the mass-separated ion.

  15. MASS DEFLECTOR APPLICATION FOR CERN’s ON-LINE ISOTOPE SEPARATOR FACILITY 073

    CERN Document Server

    Sánchez-Conejo, J

    2004-01-01

    The mass deflector application for the General Purpose Separator GPS allows splitting a beam of particles, characterized by a central mass, into two particle beams, which are sent to a high-mass and low-mass beam lines.

  16. MASS DEFLECTOR APPLICATION FOR CERN’s ON-LINE ISOTOPE SEPARATOR FACILITY 077

    CERN Document Server

    Sánchez-Conejo, J

    2004-01-01

    The mass deflector application for the General Purpose Separator GPS allows splitting a beam of particles, characterized by a central mass, into two particle beams, which are sent to a high-mass and low-mass beam lines.

  17. An Application for the On-Line Isotope Mass Separator ISOLDE facility: the Mass Control

    CERN Document Server

    Ovalle Gonzalez, E

    2003-01-01

    The Mass Control Application will calculate the magnetic field for both the HRS and GPS separators. The calculation will be carry out according to parameters either entered by the user or taken from other sources.

  18. A test-bench for isotope separator on-line of Beijing radioactive ion-beam facility

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Bing, E-mail: tangb364@126.com; Ma, Ruigang; Huang, Qinghua; Chen, Lihua; Ma, Yingjun; Cui, Baoqun; Jiang, Weisheng

    2013-12-15

    Highlights: • The modular design makes the maintenance of target station easily. • The diagnosis for low intensity beam is solved. • A positive surface ion source has been developed. -- Abstract: A test-bench for isotope separator on-line of Beijing radioactive ion-beam facility (BRISOL) has been built in China Institute of Atomic Energy (CIAE). The test-bench consists of target station, charge exchange cell, mass separator, quadrupole, hexapole, multipole and beam diagnostic system. It is nearly the same configuration as the first stage of BRISOL and all these components will be used on the BRISOL. A series of experiments have been carried out on this test-bench, and the primary results showed that all the components worked well. A Li{sup +} beam has been generated from the positive surface-ionization source and its emittance and the transmission of the beam line have been measured. The design, construction and experimental results of this test-bench have been presented.

  19. The Eurisol report. A feasibility study for a European isotope-separation-on-line radioactive ion beam facility

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-12-01

    The Eurisol project aims at a preliminary design study of the next-generation European isotope separation on-line (ISOL) radioactive ion beam (RIB) facility. In this document, the scientific case of high-intensity RIBs using the ISOL method is first summarised, more details being given in appendix A. It includes: 1) the study of atomic nuclei under extreme and so-far unexplored conditions of composition (i.e. as a function of the numbers of protons and neutrons, or the so-called isospin), rotational angular velocity (or spin), density and temperature, 2) the investigation of the nucleosynthesis of heavy elements in the Universe, an important part of nuclear astrophysics, 3) a study of the properties of the fundamental interactions which govern the properties of the universe, and in particular of the violation of some of their symmetries, 4) potential applications of RIBs in solid-state physics and in nuclear medicine, for example, where completely new fields could be opened up by the availability of high-intensity RIBs produced by the ISOL method. The proposed Eurisol facility is then presented, with particular emphasis on its main components: the driver accelerator, the target/ion-source assembly, the mass-selection system and post-accelerator, and the required scientific instrumentation. Special details of these components are given in appendices B to E, respectively. The estimates of the costs of the Eurisol, construction and running costs, have been performed in as much details as is presently possible. The total capital cost (installation manpower cost included) of the project is estimated to be of the order of 630 million Euros within 20%. In general, experience has shown that operational costs per annum for large accelerator facilities are about 10% of the capital cost. (A.C.)

  20. Operation of a high temperature ion source at the helium-jet on-line isotope separator facility HELIOS

    Energy Technology Data Exchange (ETDEWEB)

    Bruegger, M.; Hildebrand, N.; Karlewski, T.; Trautmann, N. (Mainz Univ. (Germany, F.R.). Inst. fuer Kernchemie); Mazumdar, A.K. (Marburg Univ. (Germany, F.R.). Fachbereich Physik); Herrmann, G. (Mainz Univ. (Germany, F.R.). Inst. fuer Kernchemie; Gesellschaft fuer Schwerionenforschung m.b.H., Darmstadt (Germany, F.R.))

    1985-02-01

    The performance of a high temperature ion source coupled to a helium gas-jet transport system for an efficient mass separation of neutron-rich alkaline earth and lanthanide isotopes is reported and the results of overall efficiency measurements using different cluster materials in the gas-jet are given. A fast, microprocessor controlled tape transport system for ..gamma..-spectroscopic studies on short-lived isotopes is described. Some results on the decay of 3.8sub(-s) /sup 152/Pr are presented.

  1. Development of an Ionization Scheme for Gold using the Selective Laser Ion Source at the On-Line Isotope Separator ISOLDE

    CERN Document Server

    Fedosseev, V; Marsh, B A; CERN. Geneva. AB Department

    2006-01-01

    At the ISOLDE on-line isotope separation facility, the resonance ionization laser ion source (RILIS) can be used to ionize reaction products as they effuse from the target. The RILIS process of laser step-wise resonance ionization of atoms in a hot metal cavity provides a highly element selective stage in the preparation of the radioactive ion beam. As a result, the ISOLDE mass separators can provide beams of a chosen isotope with greatly reduced isobaric contamination. The number of elements available at RILIS has been extended to 26, with the addition of a new three-step ionization scheme for gold. The optimal ionization scheme was determined during an extensive study of the atomic energy levels and auto-ionizing states of gold, carried out by means of in-source resonance ionization spectroscopy. Details of the ionization scheme and a summary of the spectroscopy study are presented.

  2. This picture was taken in 1967 during the first test of the Isotope On-Line Separator (ISOLDE) installation at the 600 MeV CERN Synchro Cyclotron.

    CERN Multimedia

    CERN PhotoLab

    1967-01-01

    When ISOLDE began operation, it was unique in the world. It used a new technique to overcome the problem of rapidly separating interesting atoms from the rest of the nuclear target. Through a combination of chemical and electromagnetic methods the different isotopes were separated and converted into an ion beam made of just one isotope. On-line production of radioactive nuclei, in this way, offered many new opportunities for physicists as it allowed them to perform previously impossible experiments on short-lived nuclei. ISOLDE has become one of CERN's major installations and it supports a broad scientific programme by providing beams to different experiments. The techniques developed at ISOLDE have opened up a new field of radioactive ion-beam accelerators, both at CERN and worldwide.

  3. Solid-state Marx based two-switch voltage modulator for the On-Line Isotope Mass Separator accelerator at the European Organization for Nuclear Research.

    Science.gov (United States)

    Redondo, L M; Silva, J Fernando; Canacsinh, H; Ferrão, N; Mendes, C; Soares, R; Schipper, J; Fowler, A

    2010-07-01

    A new circuit topology is proposed to replace the actual pulse transformer and thyratron based resonant modulator that supplies the 60 kV target potential for the ion acceleration of the On-Line Isotope Mass Separator accelerator, the stability of which is critical for the mass resolution downstream separator, at the European Organization for Nuclear Research. The improved modulator uses two solid-state switches working together, each one based on the Marx generator concept, operating as series and parallel switches, reducing the stress on the series stacked semiconductors, and also as auxiliary pulse generator in order to fulfill the target requirements. Preliminary results of a 10 kV prototype, using 1200 V insulated gate bipolar transistors and capacitors in the solid-state Marx circuits, ten stages each, with an electrical equivalent circuit of the target, are presented, demonstrating both the improved voltage stability and pulse flexibility potential wanted for this new modulator.

  4. Development of an on-line flow injection Sr/matrix separation method for accurate, high-throughput determination of Sr isotope ratios by multiple collector-inductively coupled plasma-mass spectrometry.

    Science.gov (United States)

    Galler, Patrick; Limbeck, Andreas; Boulyga, Sergei F; Stingeder, Gerhard; Hirata, Takafumi; Prohaska, Thomas

    2007-07-01

    This work introduces a newly developed on-line flow injection (FI) Sr/Rb separation method as an alternative to the common, manual Sr/matrix batch separation procedure, since total analysis time is often limited by sample preparation despite the fast rate of data acquisition possible by inductively coupled plasma-mass spectrometers (ICPMS). Separation columns containing approximately 100 muL of Sr-specific resin were used for on-line FI Sr/matrix separation with subsequent determination of (87)Sr/(86)Sr isotope ratios by multiple collector ICPMS. The occurrence of memory effects exhibited by the Sr-specific resin, a major restriction to the repetitive use of this costly material, could successfully be overcome. The method was fully validated by means of certified reference materials. A set of two biological and six geological Sr- and Rb-bearing samples was successfully characterized for its (87)Sr/(86)Sr isotope ratios with precisions of 0.01-0.04% 2 RSD (n = 5-10). Based on our measurements we suggest (87)Sr/(86)Sr isotope ratios of 0.713 15 +/- 0.000 16 (2 SD) and 0.709 31 +/- 0.000 06 (2 SD) for the NIST SRM 1400 bone ash and the NIST SRM 1486 bone meal, respectively. Measured (87)Sr/(86)Sr isotope ratios for five basalt samples are in excellent agreement with published data with deviations from the published value ranging from 0 to 0.03%. A mica sample with a Rb/Sr ratio of approximately 1 was successfully characterized for its (87)Sr/(86)Sr isotope signature to be 0.718 24 +/- 0.000 29 (2 SD) by the proposed method. Synthetic samples with Rb/Sr ratios of up to 10/1 could successfully be measured without significant interferences on mass 87, which would otherwise bias the accuracy and uncertainty of the obtained data.

  5. Isotope hydrograph separation

    Energy Technology Data Exchange (ETDEWEB)

    Fritz, P. [UFZ-Umweltforschungszentrum, Centre of Environmental Research Leipzig-Halle, Leipzig (Germany)

    2000-07-01

    Storm-runoff thus reflects the complex hydraulic behaviour of drainage basins and water-links of such systems. Water of different origin may participate in the events and in this lecture, the application of isotope techniques to separate storm hydrographs into different components will be presented.

  6. Three decades of research using IGISOL technique at the University of Jyväskylä a portrait of the Ion Guide Isotope Separator On-Line facility in Jyväskylä

    CERN Document Server

    Eronen, Tommi; Jokinen, Ari; Kankainen, Anu; Moore, Iain; Penttilä, Heikki

    2014-01-01

    The IGISOL group at the University of Jyväskyla studies the properties of nuclei far off the line of beta stability. These studies are performed locally at the Jyväskylä Ion Guide Isotope Separator On-Line (IGISOL) facility, as well as at a number of other laboratories such as the ISOLDE facility in CERN, at GANIL and in Helmholzzentrum GSI, the location of the future radioactive beam facility FAIR. The group is also actively involved in work to support the development of international future facilities EURISOL and aforementioned FAIR. This book presents  carefully selected papers to portrait the work at IGISOL. Previously published in the journals Hyperfine Interactions and European Physical Journal A.

  7. Lithium isotope separation by laser

    Energy Technology Data Exchange (ETDEWEB)

    Arisawa, T.; Maruyama, Y.; Suzuki, Y.; Shiba, K.

    1982-01-01

    A lithium isotope separation was performed using a laser isotope separation method. It was found that the lithium atoms with a natural isotopic abundance enhanced its /sup 6/Li concentration up to over 90% by tuning the laser wavelength to the /sup 2/Psub(1/2) of /sup 6/Li. Too high power, however, leads to a loss of enrichment due to the power broadening effect which was analysed by the equation of motion of density matrices.

  8. On-line blind separation of non-stationary signals

    Directory of Open Access Journals (Sweden)

    Todorović-Zarkula Slavica

    2005-01-01

    Full Text Available This paper addresses the problem of blind separation of non-stationary signals. We introduce an on-line separating algorithm for estimation of independent source signals using the assumption of non-stationary of sources. As a separating model, we apply a self-organizing neural network with lateral connections, and define a contrast function based on correlation of the network outputs. A separating algorithm for adaptation of the network weights is derived using the state-space model of the network dynamics, and the extended Kalman filter. Simulation results obtained in blind separation of artificial and real-world signals from their artificial mixtures have shown that separating algorithm based on the extended Kalman filter outperforms stochastic gradient based algorithm both in convergence speed and estimation accuracy.

  9. Operation of Electromagnetic Isotope Separator

    Institute of Scientific and Technical Information of China (English)

    MI; Ya-jing

    2015-01-01

    In 2015,we mainly completed the installation of the electromagnetic isotope separator comprehensive technical transformation projects,including the work of installation,debugging,commissioning and acceptance.In June 30,2015,according to the schedule requirements,the project

  10. Apparatus and process for separating hydrogen isotopes

    Science.gov (United States)

    Heung, Leung K; Sessions, Henry T; Xiao, Xin

    2013-06-25

    The apparatus and process for separating hydrogen isotopes is provided using dual columns, each column having an opposite hydrogen isotopic effect such that when a hydrogen isotope mixture feedstock is cycled between the two respective columns, two different hydrogen isotopes are separated from the feedstock.

  11. The separation of stable isotopes of carbon

    Science.gov (United States)

    Oziashvili, E. D.; Egiazarov, A. S.

    1989-04-01

    The present state of work on the separation of carbon isotopes by diffusion, fractional distillation, chemical isotopic exchange, and the selective excitation and dissociation of molecules in electrical discharges or in the field of laser radiation has been examined. The characteristics of new laboratory and industrial assemblies for separating carbon isotopes have been described. Promising directions of study aimed at developing effective technological processes for separating carbon isotopes have been noted. The bibliography contains 148 references.

  12. Atomic lithium vapor laser isotope separation

    CERN Document Server

    Olivares, I E

    2002-01-01

    An atomic vapor laser isotope separation in lithium was performed using tunable diode lasers. The method permits also the separation of the isotopes between the sup 6 LiD sub 2 and the sup 7 LiD sub 1 lines using a self-made mass separator which includes a magnetic sector and an ion beam designed for lithium. (Author)

  13. On the progress in stable isotope separation

    Energy Technology Data Exchange (ETDEWEB)

    Prusakov, V.N. [Kurchatov Institute, Moscow (Russian Federation)

    1994-12-31

    The principles and process of centrifuge isotope separation are reviewed; the fundamental advantage of the centrifuge over gaseous diffusion arises from the fact that the primary isotope separation effect occurs at thermodynamic equilibrium; thus, gas centrifuge enrichment uses only about 1/20 to 1/30 of the electricity per SWU (separation work unit) consumed by gaseous diffusion. The various substances that can be used in centrifuge isotope separation are listed (fluorides, oxyfluorides, {pi}-complexes, boron hydrides, metal-organic compounds, halides...). The centrifuge method productivity is much greater than with the electromagnetic separation technique; examples of centrifuge stable and radioactive isotope separation are given; the method of the residue reduction is also presented with the example of separating radioactive krypton-85 out of a nuclear reactor krypton blend. 4 figs.

  14. Delayed neutron studies of separated isotopes of Br, Rb, I, and Cs

    CERN Document Server

    Reeder, R L; Wright, J F

    1976-01-01

    Discusses delayed neutron studies of separated isotopes of Br, Rb, I, and Cs are currently in progress at the Spectrometer for On-Line Analysis of Radionuclides (SOLAR) facility operated by Battelle, Pacific Northwest Laboratories. (2 refs).

  15. The trend of stable isotope separation

    Energy Technology Data Exchange (ETDEWEB)

    Yonekawa, Shigeru [Power Reactor and Nuclear Fuel Development Corp., Kamisaibara, Okayama (Japan). Ningyo Toge Works; Aoki, Eiji; Yato, Yumio

    1994-12-01

    Recently, stable isotopes are used in the field of medical science, nuclear physics, environmental science and agriculture. This report reviews the present status of stable isotope enrichment in ORNL, Urenco, Russia and PNC. Further the utilization method of the stable isotopes in the field of medical science, nuclear power and material science are described, and the application possibility of Laser separation method and Gas Centrifuge method are estimated. There are many overseas actual results of stable isotope separation with Gas Centrifuge method, therefore this method is possible enough in principle. (author).

  16. On-line multidimensional separation systems for peptide analysis

    NARCIS (Netherlands)

    Stroink, T.

    2005-01-01

    Today, there is an increasing interest in selective and sensitive analysis of proteins and peptides with a relatively high speed. The first chapter of this thesis describes several strategies for the on-line multidimensional analysis of peptides and proteins in biological samples. This overview of t

  17. Separation of Isotopes via Dynamical Delocalization

    Institute of Scientific and Technical Information of China (English)

    Farhan Saif

    2008-01-01

    Based on the dynamical de-localization phenomenon we show that different isotopes of a material can be separated.We explain that the suggested scheme can be realized in the laboratory using presently available experimental facilities.

  18. Dye laser chain for laser isotope separation

    Science.gov (United States)

    Doizi, Denis; Jaraudias, Jean; Pochon, E.; Salvetat, G.

    1993-05-01

    Uranium enrichment by laser isotope separation uses a three step operation which requires four visible wavelengths to boost an individual U235 isotope from a low lying atomic energy level to an autoionizing state. The visible wavelengths are delivered by dye lasers pumped by copper vapor lasers (CVL). In this particular talk, a single dye chain consisting of a master oscillator and amplifier stages will be described and some of its performance given.

  19. Novel PEFC Application for Deuterium Isotope Separation

    Directory of Open Access Journals (Sweden)

    Hisayoshi Matsushima

    2017-03-01

    Full Text Available The use of a polymer electrolyte fuel cell (PEFC with a Nafion membrane for isotopic separation of deuterium (D was investigated. Mass analysis at the cathode side indicated that D diffused through the membrane and participated in an isotope exchange reaction. The exchange of D with protium (H in H2O was facilitated by a Pt catalyst. The anodic data showed that the separation efficiency was dependent on the D concentration in the source gas, whereby the water produced during the operation of the PEFC was more enriched in D as the D concentration of the source gas was increased.

  20. Isotope separation and advanced manufacturing technology

    Science.gov (United States)

    Carpenter, J.; Kan, T.

    This is the fourth issue of a semiannual report for the Isotope Separation and Advanced Materials Manufacturing (ISAM) Technology Program at Lawrence Livermore National Laboratory. Primary objectives include: (1) the Uranium Atomic Vapor Laser Isotope Separation (UAVLIS) process, which is being developed and prepared for deployment as an advanced uranium enrichment capability; (2) Advanced manufacturing technologies, which include industrial laser and E-beam material processing and new manufacturing technologies for uranium, plutonium, and other strategically important materials in support of DOE and other national applications. This report features progress in the ISAM Program from October 1993 through March 1994.

  1. Hydrogen isotope separation; Separation isotopique de l'hydrogene

    Energy Technology Data Exchange (ETDEWEB)

    Leterq, D.; Guidon, H. [CEA Bruyeres-le-Chatel, 91 (France)

    2001-12-01

    CEA-DAM has been operating for more than 20 years hydrogen isotopes separation by batch chromatography with palladium coated on alumina as absorbing material. The efforts have been focused on the development of two new separation processes: TCAP (Thermal Cycling Absorption Process) and chromatography an molecular sieve at 77 K. H{sub 2}/D{sub 2} first tests results are promising. (authors)

  2. Beam delivery for stable isotope separation

    Science.gov (United States)

    Forbes, Andrew; Strydom, Hendrick J.; Botha, Lourens R.; Ronander, Einar

    2002-10-01

    In the multi-photon dissociation process of Carbon isotope enrichment, IR photons are used to selectively excite a molecule with the given isotopic base element. This enrichment process is very sensitive to the beam's intensity and wavelength. Because the intensity is determined by the propagation of the field, the enrichment factors are also very dependent on the field propagation. In this paper, the influence of the wavelength and intensity of the beam, on the isotope selective dissociation of a CFC compound is investigated both experimentally and theoretically. Consideration is also given to some of the factors that influence the delivery of various beams to the reactor chamber, and their subsequent propagation through the reactor. The results show that suitable beam forming can lead to an improved isotope separation process.

  3. Development of proliferation resistant isotope separation technology

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Doyoung; Ko, Kwanghoon; Kim, Taeksoo; Park, Hyunmin; Lim, Gwon; Cha, Yongho; Han, Jaemin; Baik, Sunghoon; Cha, Hyungki

    2012-02-15

    This project was accomplished with an aim of establishing the industrial facilities for isotope separation in Korea. The experiment for the measurement of neutrino mass that has been an issue in physics, needs very much of enriched calcium-48 isotope. However, calcium-48 isotope can be produced only by the electro-magnetic method and, thus, its price is very expensive. Therefore, we expect that ALSIS can replace the electro-magnetic method for calcium-48 isotope production. In this research stage, the research was advanced systematically with core technologies, such as atomic vapor production, the measurement of vapor characteristics and stable and powerful laser development. These researches will be the basis of the next research stages. In addition, the international research trends and cooperation results are reported in this report.

  4. Fast ion extraction in laser isotope separation

    Energy Technology Data Exchange (ETDEWEB)

    Hazak, G.; Gell, Y.; Boneh, Y.; Goshen, S.

    1980-10-01

    An analysis of the E x B scheme for fast ion extraction in laser isotope separation is presented. Using an analytically solvable model and a numerical simulation we have found that the scheme can meet the rather severe time and space restrictions imposed by the large cross section for charge exchange.

  5. Laser isotope separation by multiple photon absorption

    Science.gov (United States)

    Robinson, C.P.; Rockwood, S.D.; Jensen, R.J.; Lyman, J.L.; Aldridge, J.P. III.

    1987-04-07

    Multiple photon absorption from an intense beam of infrared laser light may be used to induce selective chemical reactions in molecular species which result in isotope separation or enrichment. The molecular species must have a sufficient density of vibrational states in its vibrational manifold that, is the presence of sufficiently intense infrared laser light tuned to selectively excite only those molecules containing a particular isotope, multiple photon absorption can occur. By this technique, for example, intense CO[sub 2] laser light may be used to highly enrich [sup 34]S in natural SF[sub 6] and [sup 11]B in natural BCl[sub 3]. 8 figs.

  6. On-line determination of oxygen isotope ratios of water or ice by mass spectrometry.

    Science.gov (United States)

    Leuenberger, M; Huber, C

    2002-09-15

    Oxygen isotope ratio determination on any of the water phases (water vapor, water, ice) is of great relevance in different research fields such as climate and paleoclimate studies, geological surveys, and hydrological studies. The conventional technique for oxygen isotope measurement involves equilibration with carbon dioxide gas for a given time with a subsequent isotope determination. The equilibration technique is available in different layouts, but all of them are rather time-consuming. Here we report a new on-line technique that processes water samples as well as ice samples. The same principal, CO2 hydration, is used but speeded up by (i) a direct injection and full dissolution of CO2 in the water, (ii) an increased isotope exchange temperature at 50 degrees C, and (iii) a rapid gas extraction by means of an air-permeable membrane into a continuous helium flux supplying the isotope ratio mass spectrometer with the sample gas. The precision is better than 0.1/1000 which is only slightly larger than with the conventional equilibration technique. This on-line technique allows analysis of 1 m of ice with a resolution of 1-3 cm, depending on the meltwater flux, within 1 h. Similarly, continuous and fast analysis can be performed for aqueous samples for hydrological, geological, and perhaps medical applications.

  7. Hydrograph separation using stable isotopes: Review and evaluation

    Science.gov (United States)

    Klaus, J.; McDonnell, J. J.

    2013-11-01

    We reviewed isotope hydrograph separation studies.We examine methods, applications, and limitations.We summarize factors that control the event/pre-event water contributions.We outline new possible research avenues in isotope hydrograph separation.

  8. On-line blind source separation algorithm based on second order statistics

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    An on-line blind source separation (BSS) algorithm is presented in this paper under the assumption that sources are temporarily correlated signals. By using only some of the observed samples in a recursive calculation, the whitening matrix and the rotation matrix could be approximately obtained through the measurement of only one cost function. Simulations show good performance of the algorithm.

  9. Hydrogen isotope separation for fusion power applications

    Energy Technology Data Exchange (ETDEWEB)

    Smith, R., E-mail: robert.smith@ccfe.ac.uk [EURATOM/CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Whittaker, D.A.J.; Butler, B.; Hollingsworth, A.; Lawless, R.E.; Lefebvre, X.; Medley, S.A.; Parracho, A.I.; Wakeling, B. [EURATOM/CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom)

    2015-10-05

    Highlights: • Summary of the tritium plant, the Active Gas Handling System (AGHS), at JET. • Review of the Water Detritiation System (WDS) under construction. • Design of the new Material Detritiation Facility (MDF). • Review of problems in fusion related to metal/hydrogen system. - Abstract: The invited talk given at MH2014 in Salford ranged over many issues associated with hydrogen isotope separation, fusion machines and the hydrogen/metal systems found in the Joint European Torus (JET) machine located near Oxford. As this sort of talk does not lend itself well to a paper below I have attempted to highlight some of the more pertinent information. After a description of the Active Gas Handling System (AGHS) a brief summary of isotope separation systems is described followed by descriptions of three major projects currently being undertaken by the Tritium Engineering and Science Group (TESG), the upgrade to the Analytical Systems (AN-GC) at the AGH, the construction of a Water Detritiation System (WDS) and a Material Detritiation Facility (MDF). Finally, a review of some of the challenges facing fusion with respect to metal/hydrogen systems is presented.

  10. On-line technique for measuring stable oxygen and hydrogen isotopes from microliter quantities of water

    Science.gov (United States)

    Socki, R. A.; Romanek, C. S.; Gibson, E. K. Jr; Gibson EK, J. r. (Principal Investigator)

    1999-01-01

    Detailed here is a method for extracting and analyzing oxygen and hydrogen isotopes from 10 microL-sized water samples. Based on the traditional CO2-H2O equilibration technique, the oxygen isotope exchange reaction is done exclusively in sealed 6-mm (o.d.) Pyrex tubes at 25 degrees C, with full isotope exchange completed in at least 28 h. Using the same water sample employed in the 18O equilibration, D/H extractions are done in separate sealed 6-mm (o.d.) Pyrex tubes by reaction with Zn at 450 degrees C to form H2(g). Provided that a correction factor is applied to 18O analyses, accuracy and precision for both 18O and D/H are comparable to standard techniques using much larger samples.

  11. Photolytic separation of isotopes in cryogenic solution

    Science.gov (United States)

    Freund, S.M.; Maier, W.B. II; Holland, R.F.; Battie, W.H.

    Separation of carbon isotopes by photolysis of CS/sub 2/ in cryogenic solutions of nitrogen, krypton and argon with 206 nm light from an iodine resonance lamp is reported. The spectral distributionn of the ultraviolet absorption depends on solvent. Thus, in liquid nitrogen the photolytic decomposition rate of /sup 13/CS/sub 2/ is greater than that of /sup 12/CS/sub 2/ (because the absorption of 206 nm radiation is greater for /sup 13/CS/sub 2/), whereas in liquid krypton and liquid argon the reverse is true. The shift in ultraviolet spectrum is a general phenomenon readily characterized as a function of solvent polarizability, and exhibits behavior similar to that for vibrational transitions occurring in the infrared.

  12. Studies on Separation Process and Production Technology of Boron Isotope

    Directory of Open Access Journals (Sweden)

    LI Jian-ping

    2014-02-01

    Full Text Available The boron isotopes separation test was performed by chemical exchange reaction in the benzene ether -three boron fluoride system, which resulted to the boron isotopic enrichment of -10 in the liquid phase, the boron isotopic enrichment of -11 in the gas phase. After then, boron isotope separation trial production has been finished. In this process, the exchange column and complex tower normal operating parameters and the complex tower technology have been obtained, the problems of material distillation purification is solved, boron isotopes feasibility with PTFE packing enrichment is verified in an exchange column. Also, effect of operating pressure, flow and other parameters on boron -10 isotopic enrichment experiments and the effect and properties of the PTFE packing have been investigated in the existing system. All the results are very useful for the industrialization of the boron isotopes separation system.

  13. Proliferation-resistant stable isotope separation based on optical pumping

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Cheol-Jung; Park, Hyunmin; Ko, Kwang-Hoon; Lim, Gwon; Kim, Taek-Soo; Rho, Sipyo; Cha, Yong-Ho; Han, Jamin; Jeong, Do-Young [Korea Atomic Energy Research Institute, Deajeon (Korea, Republic of). Quantum Optics Division

    2008-07-01

    Korea Atomic Energy Research Institute (KAERI) has developed the laser stable isotope separation based on optical pumping which can be applied to isotopes with small isotopic shift, provides high enrichment, is economical owing to high efficiency, and is proliferation-resistant. KAERI's laser isotope separation is based on isotope-selective optical pumping by very narrow bandwidth continuous wave laser followed by efficient infrared photo-ionization. KAERI demonstrated the pilot production of Tl-203 enriching over 97 % and separating 100 mg/hr. KAERI also demonstrated the separation of Yb-168 over 30 % and Yb- 176 over 97 % with tens of mg/hr. KAERI plans to scale up the production of Tl-203 up to 500 mg/hr and apply it to separation of Zn-67, Zn-70, Ba-130 and Ca-48 which are very important in medical industry and basic sciences. (author)

  14. Isotopic separation by ion chromatography; La separation isotopique par chromatographie ionique

    Energy Technology Data Exchange (ETDEWEB)

    Albert, M.G.; Barre, Y.; Neige, R. [CEA Centre d`Etudes de la Vallee du Rhone, 26 - Pierrelatte (France). Dept. de Technologie de l`Enrichissement

    1994-12-31

    The isotopic exchange reaction and the isotopic separation factor are first recalled; the principles of ion chromatography applied to lithium isotope separation are then reviewed (displacement chromatography) and the process is modelled in the view of dimensioning and optimizing the industrial process; the various dimensioning parameters are the isotopic separation factor, the isotopic exchange kinetics and the material flow rate. Effects of the resin type and structure are presented. Dimensioning is also affected by physico-chemical and hydraulic parameters. Industrial implementation features are also discussed. 1 fig., 1 tab., 5 refs.

  15. Analysis of uranium isotope separation by redox chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Fujine, S.; Naruse, Y.; Shiba, K.

    1983-09-01

    Uranium isotope separation by redox chromatography is analytically studied. The periodic withdrawal of products and tails and the introduction of natural feed are simulated on the assumption of a square cascade for a uranium adsorption band. The influences on the separative power and the lead time until product withdrawal are investigated by varying the magnitude of the isotope separation factor, uranium band length, tails concentration, and so on. Simulating calculations indicate that using ion-exchange resins to achieve uranium isotope separation requires a very long lead time for the production of highly enriched uranium.

  16. Chlorine isotope separation using an hydrous zirconium dioxide exchanger

    Energy Technology Data Exchange (ETDEWEB)

    Heumann, K.G.; Baier, K.; Wibmer, G.

    1980-05-01

    Hydrous zirconium dioxide is used in column experiments for separating the halide ions as well as for isotope fractionation of chlorine. The preparation of the zirconium dioxide particles is carried out by homogeneous hydrolysis of a zirconyl chloride solution using hexamethylenetetramine. The separation order of the halides is I/sup -/, Br/sup -/ and Cl/sup -/ in contrast to the inverse separation order using a strongly basic anion exchange resin. In chlorine isotope separation experiments an enrichment of /sup 35/Cl/sup -/ is found in the first fractions, whereas the last fractions show a significant enrichment of /sup 37/Cl/sup -/. This also indicates an inversion of the isotope separation compared with a strongly basic anion exchange resin. A dependence of the isotope fractionation on the concentration of the NaNO/sub 3/ solution used as eluant is found. With increasing concentration the isotope fractionation decreases. Using a 0.5 M NaNO/sub 3/ solution the elementary separation effect was calculated epsilon = 6,1 x 10/sup -4/. This is one of the highest isotope fractionations known in a chloride isotope exchange system. The results show that the electrolyte behaviour of isotopes is comparable to that of a series of homologous elements.

  17. A LINEAR PROGRAMMING MODEL OF THE GASEOUSDIFFUSION ISOTOPE-SEPARATION PROCESS,

    Science.gov (United States)

    ISOTOPE SEPARATION, LINEAR PROGRAMMING ), (*GASEOUS DIFFUSION SEPARATION, LINEAR PROGRAMMING ), (* LINEAR PROGRAMMING , GASEOUS DIFFUSION SEPARATION), NUCLEAR REACTORS, REACTOR FUELS, URANIUM, PURIFICATION

  18. Analysis and separation of boron isotopes; Analyse et separation des isotopes du bore

    Energy Technology Data Exchange (ETDEWEB)

    Perie, M. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1966-11-01

    The nuclear applications of boron-10 justify the study of a method of measurement of its isotopic abundance as well as of very small traces of boron in different materials. A systematic study of thermionic emission of BO{sub 2}Na{sub 2}{sup +} has been carried out. In the presence of a slight excess of alkalis, the thermionic emission is considerably reduced. On the other hand, the addition of a mixture of sodium hydroxide-glycerol (or mannitol) to borax permits to obtain an intense and stable beam. These results have permitted to establish an operative method for the analysis of traces of boron by isotopic dilution. In other respects, the needs of boron-10 in nuclear industry Justify the study of procedures of separation of isotopes of boron. A considerable isotopic effect has been exhibited in the chemical exchange reaction between methyl borate and borate salt in solution. In the case of exchange between methyl borate and sodium borate, the elementary separation factor {alpha} is: {alpha}=(({sup 11}B/{sup 10}B)vap.)/(({sup 11}B/{sup 10}B)liq.)=1.03{sub 3}. The high value of this elementary effect has been multiplied in a distillation column in which the problem of regeneration of the reactive has been resolved. An alternative procedure replacing the alkali borate by a borate of volatile base, for example diethylamine, has also been studied ({alpha}=1,02{sub 5} in medium hydro-methanolic with 2,2 per cent water). (author) [French] Les applications nucleaires du bore 10 justifient l'etude d'une methode de mesure de son abondance isotopique dans divers materiaux ainsi que le dosage de tres faibles traces de bore. Une etude systematique de l'emission thermoionique de BO{sub 2} Na{sub 2}{sup +} a ete effectuee. En presence d'un leger exces d'alcalins, l'emission thermoionique est considerablement reduite. Par contre l'addition au borax d'un melange soude-glycerol (ou mannitol) permet d'obtenir un faisceau stable et intense

  19. On-line I-/Te- separation for the AMS analysis of 125I

    Science.gov (United States)

    Charles, C. R. J.; Cornett, R. J.; Zhao, X.-L.; Litherland, A. E.; Kieser, W. E.

    2015-10-01

    The isobar separator for anions (ISA) was used together with a 3 MV tandem accelerator mass spectrometer (AMS) to demonstrate the real time (on-line) separation of Te- from I-. Following the ion source mass spectrometry and major retardation to tens of eV, the ISA uses a radiofrequency quadrupole (RFQ) ion guide to confine and direct I- and associated Te- isobar anions through a gas-reaction cell, where chemical reactions occur at eV energies with the electronegative gas NO2. Anions are subsequently reaccelerated out of the ISA to near original ion source extraction energies for AMS analysis. At 5 mTorr NO2 in the ISA gas-reaction cell, 125Te- was observed to be attenuated by a factor of ∼107 as compared to 127I- that did not experience significant (107 relative to 37Cl- under the same ISA-AMS conditions. The preferential destruction of Te- (and S-) at eV energies in the ISA is likely due to a larger favorable destruction cross-section with NO2. This study is the first demonstration of I-Te anion separation for AMS, and makes possible the use of 125I, free of the contaminant 125Te isobar after suitable sample purification, for future 129I/125I carrier-free analyses of natural samples at ultra-low trace levels.

  20. A Stable Isotope Mass Marker for On-line Isotope Separator

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    AStableIsotopeMassMarkerforOn-lineIsotopeSeparator¥ZhaoJinhua;WangTongqin;GuoBinandFanHongmeiSofarattheHIR,FLon-lilleisotopes...

  1. Stable isotope separation; Separations physicochimiques d'isotopes stables realisations et etudes de petites productions

    Energy Technology Data Exchange (ETDEWEB)

    Botter, F.; Molinari, Ph.; Dirian, G. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    Pure deuterium has been separated from gaseous mixtures of hydrogen and deuterium by band displacement chromatography, using columns of palladium on a support. The best results were obtained with columns of Pd on sintered {alpha} alumina. With a column of this type, of total capacity about 2 liters, a preparative apparatus of low dead volume has been built which produces 1 liter of pure D{sub 2} from a 50 p. 100 D{sub 2}, 50 p. 100 100 H{sub 2} mixture in about 12 minutes. As a first approximation chromatography is likened theoretically to counter current fractionation, neglecting superficial resistance to the exchange. and also longitudinal diffusions. The number of theoretical plates required necessary for a certain enrichment of the gas phase is determined graphically or by calculation, enabling comparisons to be made between the efficiencies of columns containing different amounts of palladium. Thermal Diffusion: For the separation of hydrogen isotopes a thermal diffusion installation, made of stainless steel and entirely tele-commanded has been constructed. The separation cascade is made up of two identical pairs of hot wire columns. Each pair can work separately or they may be connected by a thermosyphon. The temperature of the hot wire is kept at around 1000 deg C by direct current. With this installation, hydrogen samples with a deuterium content lower than o,5 ppm were obtained from a gas originally containing 32 ppm. It was thus possible to prepare tritium of 99,3 p. 100 concentration from gas with an initial content of 6 p. 100. For quantitative separation of xenon enriched five time in {sup 124}Xe by thermal diffusion, two identical cascades were constructed, each consisting of 5 columns, working in parallel and the two being connected by thermosyphon or by a capillary tube linked to a thermal gas oscillation. The central tungsten wire is heated to 1200 deg C. The columns are grouped like cluster of a heat exchanger, in shell of 30 cm diameter through

  2. Chromatographic zinc isotope separation by phenol formaldehyde benzo crown resin.

    Science.gov (United States)

    Ding, Xingcheng; Nomura, Masao; Suzuki, Tatsuya; Sugiyama, Yuichi; Kaneshiki, Toshitaka; Fujii, Yasuhiko

    2006-04-28

    New types of phenol formaldehyde resin having benzo crown as a functional group were synthesized and applied to zinc isotope chromatographic operation. Zinc adsorption and isotope separation capacities were dramatically improved by using phenol formaldehyde benzo-15-crown-5 resin. Zinc batch adsorption tests were performed by various dehydrated organic solvents. Separation coefficient, epsilon 8.1 x 10(-4) and height equivalent to a theoretical plate (HETP) 0.105 cm for the isotopic pair of 68Zn/64Zn in phenol formaldehyde benzo-15-crown-5 resin were obtained in the case of acetone as the solvent at 298+/-1K.

  3. Development of O-18 stable isotope separation technology using membrane

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jae Woo; Kim, Taek Soo; Choi, Hwa Rim; Park, Sung Hee; Lee, Ki Tae; Chang, Dae Shik

    2006-06-15

    The ultimate goal of this investigation is to develop the separation technology for O-18 oxygen stable isotope used in a cyclotron as a target for production of radioisotope F-18. F-18 is a base material for synthesis of [F-18]FDG radio-pharmaceutical, which is one of the most important tumor diagnostic agent used in PET (Positron Emission Tomography). More specifically, this investigation is focused on three categories as follow, 1) development of the membrane distillation isotope separation process to re-enrich O-18 stable isotope whose isotopic concentration is reduced after used in a cyclotron, 2) development of organic impurity purification technology to remove acetone, methanol, ethanol, and acetonitrile contained in a used cyclotron O-18 enriched target water, and 3) development of a laser absorption spectroscopic system for analyzing oxygen isotopic concentration in water.

  4. Hydrogen isotope separation by multiple photodissociation of dichlorofluoromethane

    Energy Technology Data Exchange (ETDEWEB)

    Arisawa, T.; Kato, M.; Maruyama, Y.; Shiba, K. (Japan Atomic Energy Research Inst., Tokai, Ibaraki. Tokai Research Establishment)

    1982-06-14

    Multiple photodissociation rates of dichlorofluoromethane were measured from the dissociated products and/or the residual gases which escaped dissociation. It is shown that the relationship between the separation factor for the hydrogen isotopes in the residual gases and that in the products is in good agreement with theory. It is also verified that hydrogen isotope separation is influenced by the chlorine isotopes contained in the molecules. The experimental data obtained are compared with the theoretical dissociation model including two-sets of kinetic equations in which energy exchanges between two kinds of isotopic molecules are considered. This gives a good explanation for the dependence of the dissociation rate on the laser intensity and pressure, and the pressure dependence of the separation factor.

  5. Basic separative power of multi-component isotopes separation in a gas centrifuge

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Hongmin; Lei, Zengguang; Zhuge, Fu [Institute of Physical and Chemical Engineering, Tianjin (China)

    2008-07-01

    On condition that the overall separation factor per unit exists in centrifuge for multi-component isotopes separation, the relations between separative power of each component and molecular weight have been investigated in the paper while the value function and the separative power of binary-component separation are adopted. The separative power of each component is proportional to the square of the molecular weight difference between its molecular weight and the average molecular weight of other remnant components. In addition, these relations are independent on the number of the components and feed concentrations. The basic separative power and related expressions, suggested in the paper, can be used for estimating the separative power of each component and analyzing the separation characteristics. The most valuable application of the basic separative power is to evaluate the separative capacity of centrifuge for multi-component isotopes. (author)

  6. Chlorine isotope separation using an hydrous zirconium dioxide exchanger

    Energy Technology Data Exchange (ETDEWEB)

    Heumann, K.G.; Baier, K.; Wibmer, G.

    1980-05-01

    Hydrous zirconium dioxide is used in column experiments for separating the halide ions as well as for isotope fractionation of chlorine. The preparation of the zirconium dioxide particles is carried out by homogeneous hydrolysis of a zirconyl chloride solution using hexamethylenetetramine. The separation order of the halides is I/sup -/, Br/sup -/ and Cl/sup -/ in contrast to the inverse separation order using a strongly basic anion exchange resin. In chlorine isotope separation experiments an enrichment of /sup 35/Cl/sup -/ is found in the first fractions, whereas the last fractions show a significant enrichment of /sup 37/Cl/sup -/. This also indicates an inversion of the isotope separation compared with a strongly basic anion exchange resin. A dependence of the isotope fractionation on the concentration of the NaNO/sub 3/ solution used as eluant is found. With increasing concentration the isotope fractionation decreases. Using a 0.5 M NaNO/sub 3/ solution the elementary separation effect was calculated epsilon done on different tantalum parts to determine the amount of dissolved hydrogen.

  7. Design of the Advanced Rare Isotope Separator ARIS at FRIB

    Energy Technology Data Exchange (ETDEWEB)

    Hausmann, M., E-mail: hausmann@frib.msu.edu [Facility for Rare Isotope Beams, Michigan State University, East Lansing, MI 48824 (United States); Aaron, A.M. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Amthor, A.M. [Dept. of Physics and Astronomy, Bucknell University, Lewisburg, PA 17837 (United States); Avilov, M.; Bandura, L.; Bennett, R.; Bollen, G.; Borden, T. [Facility for Rare Isotope Beams, Michigan State University, East Lansing, MI 48824 (United States); Burgess, T.W. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Chouhan, S.S. [Facility for Rare Isotope Beams, Michigan State University, East Lansing, MI 48824 (United States); Graves, V.B. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Mittig, W. [Facility for Rare Isotope Beams, Michigan State University, East Lansing, MI 48824 (United States); National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI 48824 (United States); Morrissey, D.J. [National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI 48824 (United States); Pellemoine, F.; Portillo, M.; Ronningen, R.M.; Schein, M. [Facility for Rare Isotope Beams, Michigan State University, East Lansing, MI 48824 (United States); Sherrill, B.M. [Facility for Rare Isotope Beams, Michigan State University, East Lansing, MI 48824 (United States); National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI 48824 (United States); Zeller, A. [Facility for Rare Isotope Beams, Michigan State University, East Lansing, MI 48824 (United States)

    2013-12-15

    The Facility for Rare Isotopes Beams (FRIB) at Michigan State University will use projectile fragmentation and induced in-flight fission of heavy-ion primary beams at energies of 200 MeV/u and higher and at a beam power of 400 kW to generate rare isotope beams for experiments in nuclear physics, nuclear astrophysics, and fundamental symmetries, as well as for societal needs. The Advanced Rare Isotope Separator (ARIS) has been designed as a three-stage fragment separator for the efficient collection and purification of the rare isotope beams of interest. A vertically bending preseparator (first stage) with production target and beam dump is fully integrated into a production target facility hot cell with remote handling. The new separator compresses the accepted momentum width of up to ±5% of the beam by a factor of three in the standard operational mode. Provisions for alternate operational modes for specific cases are included in the design. This preseparator is followed by two, horizontally-bending separator stages (second and third stages) utilizing the magnets from the existing A1900 fragment separator at the National Superconducting Cyclotron Laboratory (NSCL). These stages can alternatively be coupled to a single high-resolution separator stage, resulting in the flexibility to optimize the operation for different experiments, including momentum tagging and in-flight particle identification of rare isotope beams. The design of ARIS will be presented with an emphasis on beam physics characteristics, and anticipated operational modes will be described.

  8. Production of chemically reactive radioactive ion beams through on-line separation; Production de faisceaux d'ions radioactifs chimiquement reactifs par separation en ligne

    Energy Technology Data Exchange (ETDEWEB)

    Joinet, A

    2003-10-01

    The ISOL (isotope separation on line) allows the production of secondary radioactive ion beams through spallation or fragmentation or fission reactions that take place in a thick target bombarded by a high intensity primary beam. The challenge is to increase the intensity and purity of the radioactive beam. The optimization of the system target/source requires the right choice of material for the target by taking into account the stability of the material, its reactivity and the ionization method used. The target is an essential part of the system because radioactive elements are generated in it and are released more or less quickly. Tests have been made in order to select the best fitted material for the release of S, Se, Te, Ge and Sn. Materials tested as target filling are: ZrO{sub 2}, Nb, Ti, V,TiO{sub 2}, CeO{sub x}, ThO{sub 2}, C, ZrC{sub 4} and VC). Other molecules such as: COSe, COS, SeS, COTe, GeS, SiS, SnS have been studied to ease the extraction of recoil nuclei (Se, S, Te, Ge and Sn) produced inside the target.

  9. Electromagnetic separation of stable isotopes at China Institute of Atomic Energy

    Science.gov (United States)

    Meiqin, Xiao; Hongyou, Lu; Shijun, Su; Zhizhou, Lin

    1993-09-01

    Electromagnetic separation of stable isotopes at CIAE is described. The separators, the ion sources used, the isotopes separated and their applications are introduced. The improvement of a 180° production separator is also described.

  10. Production of stable isotopes utilizing the plasma separation process

    Science.gov (United States)

    Bigelow, T. S.; Tarallo, F. J.; Stevenson, N. R.

    2005-12-01

    A plasma separation process (PSP) is being operated at Theragenics Corporation's®, Oak Ridge, TN, facility for the enrichment of stable isotopes. The PSP utilizes ion cyclotron mass discrimination to separate isotopes on a relatively large scale. With a few exceptions, nearly any metallic element could be processed with PSP. Output isotope enrichment factor depends on natural abundance and mass separation and can be fairly high in some cases. The Theragenics™ PSP facility is believed to be the only such process currently in operation. This system was developed and formerly operated under the US Department of Energy Advanced Isotope Separation program. Theragenics™ also has a laboratory at the PSP site capable of harvesting the isotopes from the process and a mass spectrometer system for analyzing enrichment and product purity. Since becoming operational in 2002, Theragenics™ has utilized the PSP to separate isotopes of several elements including: dysprosium, erbium, gadolinium, molybdenum and nickel. Currently, Theragenics™ is using the PSP for the separation of 102Pd, which is used as precursor for the production of 103Pd. The 103Pd radioisotope is the active ingredient in TheraSeed®, which is used in the treatment of early stage prostate cancer and being investigated for other medical applications. New industrial, medical and research applications are being investigated for isotopes that can be enriched on the PSP. Pre-enrichment of accelerator or reactor targets offers improved radioisotope production. Theragenics operates 14 cyclotrons for proton activation and has access to HFIR at ORNL for neutron activation of radioisotopes.

  11. Investigation of the Photochemical Method for Uranium Isotope Separation

    Science.gov (United States)

    Urey, H. C.

    1943-07-10

    To find a process for successful photochemical separation of isotopes several conditions have to be fulfilled. First, the different isotopes have to show some differences in the spectrum. Secondly, and equally important, this difference must be capable of being exploited in a photochemical process. Parts A and B outline the physical and chemical conditions, and the extent to which one might expect to find them fulfilled. Part C deals with the applicability of the process.

  12. Study on the Effect of the Separating Unit Optimization on the Economy of Stable Isotope Separation

    Directory of Open Access Journals (Sweden)

    YANG Kun

    2015-01-01

    Full Text Available An economic criterion called as yearly net profit of single separating unit (YNPSSU was presented to evaluate the influence of structure optimization on the economy. Using YNPSSU as a criterion, economic analysis was carried out for the structure optimization of separating unit in the case of separating SiF4 to obtain the 28Si and 29Si isotope. YNPSSU was calculated and compared with that before optimization. The results showed that YNPSSU was increased by 12.3% by the structure optimization. Therefore, the structure optimization could increase the economy of the stable isotope separation effectively.

  13. Laser isotope separation and proliferation risks

    Energy Technology Data Exchange (ETDEWEB)

    Fuss, Werner

    2015-02-15

    There is an ongoing discussion on the proliferation danger of laser enrichment of uranium by the Silex process. Here this risk is compared to that of other processes, in particular centrifuges. The two methods need a similar size of the plant for a comparable production rate (in separative work units per year) and the time and costs for their construction do not differ much. This conclusion from published material does not depend on technical details of Silex. But enough details are known to allow for additional conclusions: Whereas the selectivity (enrichment factor) in the Silex process seems higher, the energy consumption is probably larger. Due to the laser's repetition rate being insufficient for the molecular beam, the method has probably a low depletion factor; this is a serious disadvantage for cascading for high enrichment such as for bomb uranium, although it may be acceptable for low enrichment without cascading for reactor purposes.

  14. Gas chromatographic separation of hydrogen isotopes using metal hydrides

    Energy Technology Data Exchange (ETDEWEB)

    Aldridge, F.T.

    1984-05-09

    A study was made of the properties of metal hydrides which may be suitable for use in chromatographic separation of hydrogen isotopes. Sixty-five alloys were measured, with the best having a hydrogen-deuterium separation factor of 1.35 at 60/sup 0/C. Chromatographic columns using these alloys produced deuterium enrichments of up to 3.6 in a single pass, using natural abundance hydrogen as starting material. 25 references, 16 figures, 4 tables.

  15. THE SEPARATION OF URANIUM ISOTOPES BY GASEOUS DIFFUSION: A LINEAR PROGRAMMING MODEL,

    Science.gov (United States)

    URANIUM, ISOTOPE SEPARATION), (*GASEOUS DIFFUSION SEPARATION, LINEAR PROGRAMMING ), (* LINEAR PROGRAMMING , GASEOUS DIFFUSION SEPARATION), MATHEMATICAL MODELS, GAS FLOW, NUCLEAR REACTORS, OPERATIONS RESEARCH

  16. Single Photon Atomic Sorting: Isotope Separation with Maxwell's Demon

    CERN Document Server

    Raizen, M G; Jerkins, M

    2010-01-01

    Isotope separation is one of the grand challenges of modern society and holds great potential for basic science, medicine, energy, and defense. We consider here a new and general approach to isotope separation. The method is based on an irreversible change of the mass-to-magnetic moment ratio of a particular isotope in an atomic beam, followed by deflection in a magnetic field gradient. The underlying mechanism is a reduction of the entropy of the beam by the information of a single-scattered photon for each atom that is separated. We numerically simulate isotope separation for a range of examples. The first class of atoms we consider are those that have zero magnetic moment in their ground electronic state. A laser induces an irreversible transition to a metastable state, followed by magnetic deflection. The second (larger) class of atoms we consider are those that have a magnetic moment in their ground state. The magnetic stretch-state is deflected in one zone of a magnetic field gradient, followed by a las...

  17. Isotope separation of the Yb-168 stable isotope for low energy gamma ray sources

    Energy Technology Data Exchange (ETDEWEB)

    Park, Hyun Min; Kwon, Duck Hee; Cha, Yong Ho; Lee, Ki Tae; Nam, Sung Mo; Yoo, Jaek Won; Han, Jae Min; Rhee, Yong Joo [Lab. of Quantum Optics, Korea Atomic Energy Research Institute, Taejeon (Korea, Republic of)

    2003-07-01

    We developed laser isotope separation technology of stable isotope of low melting point metals. Yb-168 can be effectively used in non-destructive testing (NDT) after it is transformed to Yb-168 by neutron irradiation in a nuclear reactor. For this application of Yb-168, the isotope purity of it should be enhanced to more than 15% from the natural abundance of 0.135%. Our isotope separation system consist of laser system, Yb vapor generating system, and photoionized particle extraction system. For the system, we developed a diode-pumped slid-state laser of high-repetition rate and 3-color dye lasers. Yb vapor was generated by heating solid Yb sample resistively. The photo-ion produced by resonance ionization were extracted by a devised extractor. We produced enriched Yb metal more than 20 mg with the abundance of 25.8% of Yb-168 in the Yb (NO{sub 3}){sub 3}.

  18. Rotation and instabilities for isotope and mass separation

    Science.gov (United States)

    Rax, J.-M.; Gueroult, R.

    2016-10-01

    Rotating plasmas have the potential to offer unique capabilities for isotope and mass separation. Among the various electric and magnetic field configurations offering mass separation capabilities, rotating plasmas produced through static or oscillating fields are shown to be a leading candidate for tackling the unsolved problem of large-scale plasma separation. The successful development and deployment of industrial-scale plasma separation technologies could, among many other applications, provide an innovative path towards advanced sustainable nuclear energy. In this context, the potential and versatility of plasma rotation induced by rotating magnetic fields is uncovered and analysed. Analytical stability diagrams are derived from rotating ion orbits as a function of ion mass. Based on these findings, the basic principles of a rotating field plasma separator are then introduced. In light of these results, challenges associated with this original separation process are underlined, and the main directions for a future research program aimed at this important unsolved problem of applied plasma physics are identified.

  19. The Cryo-Thermochromatographic Separator (CTS) A new rapid separation and alpha-detection system for on-line chemical studies of highly volatile osmium and hassium (Z=108) tetroxides

    CERN Document Server

    Kirbach, U W; Gregorich, K E; Lee, D M; Ninov, V; Omtvedt, J P; Patin, J B; Seward, N K; Strellis, D A; Sudowe, R; Türler, A; Wilk, P A; Zielinski, P M; Hoffman, D C; Nitsche, H

    2002-01-01

    The Cryo-Thermochromatographic Separator (CTS) was designed and constructed for rapid, continuous on-line separation and simultaneous detection of highly volatile compounds of short-lived alpha-decaying isotopes of osmium and hassium (Hs, Z=108). A flowing carrier gas containing the volatile species is passed through a channel formed by two facing rows of 32 alpha-particle detectors, cooled to form a temperature gradient extending from 247 K at the channel entrance down to 176 K at the exit. The volatile species adsorb onto the SiO sub 2 -coated detector surfaces at a characteristic deposition temperature and are identified by their observed alpha-decay energies. The CTS was tested on-line with OsO sub 4 prepared from sup 1 sup 6 sup 9 sup - sup 1 sup 7 sup 3 Os isotopes produced in sup 1 sup 1 sup 8 sup , sup 1 sup 2 sup 0 Sn( sup 5 sup 6 Fe, 3,4,5n) reactions. An adsorption enthalpy for OsO sub 4 of -40.2+-1.5 kJ/mol on SiO sub 2 was deduced by comparing the measured deposition distribution with Monte Carlo...

  20. Biomedical research applications of electromagnetically separated enriched stable isotopes

    Science.gov (United States)

    Lambrecht, R. M.

    The current and projected annual requirements through 1985 for stable isotopes enriched by electromagnetic separation methods were reviewed for applications in various types of biomedical research: (1) medical radiosiotope production, labeled compounds, and potential radio-pharmaceuticals; (2) nutrition, food science, and pharmacology: (3) metallobiochemistry and environmental toxicology; (4) nuclear magnetic resonance, electron paramagnetic resonance, and moessbauer spectroscopy in biochemical, biophysical, and biomedical research; and (5) miscellaneous advances in radioactive and nonradioactive tracer technology. Radioisotopes available from commercial sources or routinely used in clinical nuclear medicine were excluded. Current requirements for enriched stable isotopes in biomedical research are not being satisfied. Severe shortages exist for Mg 26, Ca 43, Zn 70, Se 76, Se 77, Se 78, Pd 102, Cd 111, Cd 113, and Os 190. Many interesting and potentially important investigations in biomedical research require small quantities of specific elements at high isotopic enrichments.

  1. Isotope separation with the RICH detector of the AMS Experiment

    CERN Document Server

    Arruda, Luísa; Borges, João; Carmo, Fernando; Gonçalves, Patrícia; Pereira, Rui; Pimenta, Mário

    2007-01-01

    The Alpha Magnetic Spectrometer (AMS), to be installed on the International Space Station (ISS) in 2008, is a cosmic ray detector with several subsystems, one of which is a proximity focusing Ring Imaging Cherenkov (RICH) detector. This detector will be equipped with a dual radiator (aerogel+NaF), a lateral conical mirror and a detection plane made of 680 photomultipliers and light guides, enabling precise measurements of particle electric charge and velocity. Combining velocity measurements with data on particle rigidity from the AMS Tracker it is possible to obtain a measurement for particle mass, allowing the separation of isotopes. A Monte Carlo simulation of the RICH detector, based on realistic properties measured at ion beam tests, was performed to evaluate isotope separation capabilities. Results for three elements -- H (Z=1), He (Z=2) and Be (Z=4) -- are presented.

  2. Uranium isotope separation from 1941 to the present

    Energy Technology Data Exchange (ETDEWEB)

    Maier-Komor, Peter, E-mail: Peter@Maier-Komor.d [Retired from Physik-Department E12, Technische Universitaet Muenchen, D-85747 Garching (Germany)

    2010-02-11

    Uranium isotope separation was the key development for the preparation of highly enriched isotopes in general and thus became the seed for target development and preparation for nuclear and applied physics. In 1941 (year of birth of the author) large-scale development for uranium isotope separation was started after the US authorities were warned that NAZI Germany had started its program for enrichment of uranium and might have confiscated all uranium and uranium mines in their sphere of influence. Within the framework of the Manhattan Projects the first electromagnetic mass separators (Calutrons) were installed and further developed for high throughput. The military aim of the Navy Department was to develop nuclear propulsion for submarines with practically unlimited range. Parallel to this the army worked on the development of the atomic bomb. Also in 1941 plutonium was discovered and the production of {sup 239}Pu was included into the atomic bomb program. {sup 235}U enrichment starting with natural uranium was performed in two steps with different techniques of mass separation in Oak Ridge. The first step was gas diffusion which was limited to low enrichment. The second step for high enrichment was performed with electromagnetic mass spectrometers (Calutrons). The theory for the much more effective enrichment with centrifugal separation was developed also during the Second World War, but technical problems e.g. development of high speed ball and needle bearings could not be solved before the end of the war. Spying accelerated the development of uranium separation in the Soviet Union, but also later in China, India, Pakistan, Iran and Iraq. In this paper, the physical and chemical procedures are outlined which lead to the success of the project. Some security aspects and Non-Proliferation measures are discussed.

  3. Uranium isotope separation from 1941 to the present

    Science.gov (United States)

    Maier-Komor, Peter

    2010-02-01

    Uranium isotope separation was the key development for the preparation of highly enriched isotopes in general and thus became the seed for target development and preparation for nuclear and applied physics. In 1941 (year of birth of the author) large-scale development for uranium isotope separation was started after the US authorities were warned that NAZI Germany had started its program for enrichment of uranium and might have confiscated all uranium and uranium mines in their sphere of influence. Within the framework of the Manhattan Projects the first electromagnetic mass separators (Calutrons) were installed and further developed for high throughput. The military aim of the Navy Department was to develop nuclear propulsion for submarines with practically unlimited range. Parallel to this the army worked on the development of the atomic bomb. Also in 1941 plutonium was discovered and the production of 239Pu was included into the atomic bomb program. 235U enrichment starting with natural uranium was performed in two steps with different techniques of mass separation in Oak Ridge. The first step was gas diffusion which was limited to low enrichment. The second step for high enrichment was performed with electromagnetic mass spectrometers (Calutrons). The theory for the much more effective enrichment with centrifugal separation was developed also during the Second World War, but technical problems e.g. development of high speed ball and needle bearings could not be solved before the end of the war. Spying accelerated the development of uranium separation in the Soviet Union, but also later in China, India, Pakistan, Iran and Iraq. In this paper, the physical and chemical procedures are outlined which lead to the success of the project. Some security aspects and Non-Proliferation measures are discussed.

  4. New on-line method for water isotope analysis of speleothem fluid inclusions using laser absorption spectroscopy (WS-CRDS)

    Science.gov (United States)

    Affolter, S.; Fleitmann, D.; Leuenberger, M.

    2014-01-01

    A new online method to analyse water isotopes of speleothem fluid inclusions using a wavelength scanned cavity ring down spectroscopy (WS-CRDS) instrument is presented. This novel technique allows us to simultaneously measure hydrogen and oxygen isotopes for a released aliquot of water. To do so, we designed a new simple line that allows the on-line water extraction and isotope analysis of speleothem samples. The specificity of the method lies in the fact that fluid inclusions release is made on a standard water background, which mainly improves the δD reliability. To saturate the line, a peristaltic pump continuously injects standard water into the line that is permanently heated to 140 °C and flushed with dry nitrogen gas. This permits instantaneous and complete vaporisation of the standard water resulting in an artificial water background with well-known δD and δ18O values. The speleothem sample is placed into a copper tube, attached to the line and after system stabilisation is crushed using a simple hydraulic device to liberate speleothem fluid inclusions water. The released water is carried by the nitrogen/standard water gas stream directly to a Picarro L1102-i for isotope determination. To test the accuracy and reproducibility of the line and to measure standard water during speleothem measurements a syringe injection unit was added to the line. Peak evaluation is done similarly as in gas chromatography to obtain δD and δ18O isotopic composition of measured water aliquots. Precision is better than 1.5‰ for δD and 0.4‰ for δ18O for water measurement for an extended range (-210 to 0‰ for δD and -27 to 0‰ for δ18O) primarily dependent on the amount of water released from speleothem fluid inclusions and secondarily on the isotopic composition of the sample. The results show that WS-CRDS technology is suitable for speleothem fluid inclusion measurements and gives results that are comparable to Isotope Ratio Mass Spectrometry (IRMS) technique.

  5. Control strategies for laser separation of carbon isotopes

    Indian Academy of Sciences (India)

    V Parthasarathy; A K Nayak; S K Sarkar

    2002-12-01

    Laser isotope separation (LIS) by infrared laser chemistry of polyatomic molecules has come a long way since its discovery. The last decade has seen considerable efforts in scaling up of the process for light elements like carbon, oxygen and silicon. These efforts aim at ways to improve both the enrichment factor and the throughput. The achievement is quite significant especially for carbon isotope separation wherein macroscopic operating scales have been realized. We report our studies on the IR laser chemistry of two promising systems, viz. neat CF2HCl and CF3Br/Cl2. We have investigated conditions for optimizing the dissociation yield and selectivity using natural samples containing 1.1 % C-13. We also highlight our current efforts for scaling up the process. These include the design aspects of a photochemical reactor with multipass refocusing Herriott optics for efficient photon utilization, development of a cryogenic distillation set up and a preparative gas chromatograph for large scale separation/collection of the isotopically enriched photoproduct in the post-irradiation stage.

  6. Deciphering Carbon Isotope Excursions in Separated Biogenic and Diagenetic Carbonates

    Science.gov (United States)

    Hermoso, M.; Minoletti, F.; Hesselbo, S.; Jenkyns, H.; Rickaby, R.; Diester-Haass, L.; Delsate, D.

    2008-12-01

    shift in the bulk carbonate record. Contrasts in the amplitude of the carbon-isotope excursion at the single-species level compared to inorganic calcite and organic subtrate, should improve our understanding of the evolution of the water column composition through these major C-cycling perturbation events, and how marine calcifiers have fedback during such events, and eventually contribute for better understanding ocean-climate dynamics through time and into the future. Minoletti, F., Hermoso, M. and Gressier, V. (accepted). Separation of sedimentary micron-sized particles for palaeoceanography and calcareous nannoplankton biogeochemistry. Nature protocols.

  7. Enrichment of stable iostopes by electromagnetic isotope separation and plasma separation

    Energy Technology Data Exchange (ETDEWEB)

    Aaron, W.S.; Bigelow, T.S.; Collins, E.D.; Tracy, J.G. [Oak Ridge National Lab., TN (United States)

    1996-10-01

    Enriched stable isotopes for use in research, medicine, and industrial applications have been provided by the Oak Ridge National Laboratory for almost fifty years. The enrichment method employed is the Electromagnetic Isotope Separation (EMIS) process. Recent reviews of alternative separation processes have indicated that the Plasma Separation Process (PSP) is best suited to complement the current EMIS process. The PSP is based on the ion cyclotron resonance of a charged particle in a uniform magnetic field. This process, along with an overview of the EMIS process and their complementary use will be described. Use of the Proof of Principle, M2B, and the Production Prototype Module (PPM) devices will augment the current process to provide better enriched products for the user.

  8. Study on the Effect of the Separating Unit Optimization on the Economy of Stable Isotope Separation

    OpenAIRE

    Yang, Kun; MOU Hong

    2015-01-01

    An economic criterion called as yearly net profit of single separating unit (YNPSSU) was presented to evaluate the influence of structure optimization on the economy. Using YNPSSU as a criterion, economic analysis was carried out for the structure optimization of separating unit in the case of separating SiF4 to obtain the 28Si and 29Si isotope. YNPSSU was calculated and compared with that before optimization. The results showed that YNPSSU was increased by 12.3% by the structure optimization...

  9. On-line coupling of an ion chromatograph to the ICP-MS: Separations with a cation exchange chromatography column

    Energy Technology Data Exchange (ETDEWEB)

    Roellin, Stefan [Studsvik Nuclear AB, Nykoeping (Sweden)

    1999-12-01

    An ion chromatography system was coupled on-line to the ICP-MS. All separations were made with a cation exchange chromatography column. Fundamental laws about elution parameters affecting individual retention times and elution forms are explained by applying a proper ion exchange mechanism for the isocratic elution (separations with constant eluent concentration) of mono-, di-, tri-, and tetravalent cations and the actinide species MO{sub 2}{sup +} and MO{sub 2}{sup 2+}. A separation method with two eluents has been investigated to separate mono- from divalent ions in order to separate isobaric overlaps of Rb/Sr and Cs/Ba. The ions normally formed by actinides in aqueous solutions in the oxidation states III to VI are M{sup 3+}, M{sup 4+}, MO{sub 2}{sup +} and MO{sub 2}{sup 2+} respectively. Elution parameters were investigated to separate all four actinide species from each other in order to separate isobaric overlaps of the actinides Np, Pu, U and Am. A major question of concern over the possible release of actinides to the environment is the speciation of actinides within their four possible oxidation states. To check the possibility of speciation analysis with ion chromatography, a separation method was investigated to separate U{sup 4+} and UO{sub 2}{sup 2+} without changing the redox species composition during the separation. First results of Pu speciation analysis showed that Pu could be eluted as three different species. Pu(VI) was always eluting at the same time as Np(V). This was surprising as Pu(VI) is expected to have the same chemical characteristics as U(VI) and thus was expected to elute at the same time as U(VI)

  10. The Laboratory for Laser Energetics’ Hydrogen Isotope Separation System

    Energy Technology Data Exchange (ETDEWEB)

    Shmayda, W.T., E-mail: wshm@lle.rochester.edu; Wittman, M.D.; Earley, R.F.; Reid, J.L.; Redden, N.P.

    2016-11-01

    The University of Rochester’s Laboratory for Laser Energetics has commissioned a hydrogen Isotope Separation System (ISS). The ISS uses two columns—palladium on kieselguhr and molecular sieve—that act in a complementary manner to separate the hydrogen species by mass. The 4-sL per day throughput system is compact and has no moving parts. The columns and the attendant gas storage and handling subsystems are housed in a 0.8 -m{sup 3} glovebox. The glovebox uses a helium cover gas that is continuously processed to extract oxygen and water vapor that permeates through the glovebox gloves and any tritium that is released while attaching or detaching vessels to add feedstock to or drawing product from the system. The isotopic separation process is automated and does not require manual intervention. A total of 315 TBq of tritium was extracted from 23.6 sL of hydrogen with tritium purities reaching 99.5%. Deuterium was the sole residual component in the processed gas. Raffinate contained 0.2 TBq of activity was captured for reprocessing. The total emission from the system to the environment was 0.4 GBq over three weeks.

  11. Modelling of multifrequency IRMPD for laser isotope separation

    Indian Academy of Sciences (India)

    Akshaya K Nayak; Sisir K Sarkar

    2002-12-01

    The process of infrared multiple photon dissociation (IRMPD) of molecules is of great fundamental importance and has practical significance, such as isotope separation etc. Unfortunately, a clear insight into the process has been hindered by the bewildering array of important variables affecting MPD. The dissociation probability () i.e. the yield has been found to be a sensitive function of laser fluence along with numerous other parameters like laser frequency, gas pressure etc. We have shown that in single frequency IRMPD, an accurate quantitative characterization of the dissociation probability can be adequately expressed by a `power law’ model with two fitting parameters namely critical fluence, and multiphoton order, . This model was exploited in analysing our MPD results on various systems. However, the small isotope shift encountered in heavy elements and the sticking phenomenon observed in small light molecules restrict respectively the separation factor and the dissociation yield. These problems can effectively be tackled by irradiation with multifrequency laser beams which can be chosen appropriately on the basis of spectroscopic features. Based on our success in single frequency model, multifrequency IRMPD is modelled by a functional form containing the product of power law terms for individual fluences on irradiation frequencies. This model is successfully benchmarked with our experimental results on multifrequency LIS of tritium. Such knowledge can be utilized for appropriate separation process design, evaluation and optimization.

  12. Liquid-chromatographic separation and on-line bioluminescence detection of creatine kinase isoenzymes

    Energy Technology Data Exchange (ETDEWEB)

    Bostick, W.D.; Denton, M.S.; Dinsmore, S.R.

    1980-01-01

    Isoenzymes of creatine kinase were separated by anion-exchange chromatography, with use of an elution gradient containing lithium acetate (0.1 to 0.6 mol/L). A stream splitter was used to divert a 5% side stream of column effluent, which was subsequently mixed with the reagents necessary for bioluminescence assay of the separated isoenzymes. The use of the stream splitter greatly decreased the rate of consumption of reagent and, when combined with a peristaltic pumping system, permitted independent control of the side-stream flow rate. Thus both the residence interval in a delay coil in which the ATP reaction product is formed and the bioluminescence emission was monitored in a flow-through fluorometer without use of an external light source or filters. Separation and detection of the isoenzymes of creatine kinase were rapid, sensitive, and highly selective. The incremental decrease of bioluminescence response owing to inhibition by the ions in the eluent was less than 31% across the entire gradient.

  13. The control system of the CERN-ISOLDE on-line mass-separator facility

    Energy Technology Data Exchange (ETDEWEB)

    Jonsson, O.C.; Bret, A.; Catherall, R.; Deloose, I.; Focker, G.J.; Forkel, D.; Kugler, E.; Olesen, G.; Pace, A.; Ravn, H.L.; Shering, G.; Tengblad, O. (CERN, Geneva (Switzerland)); Borch, O. (Aalborg Univ. (Denmark). Inst. of Electronic Systems); Richard-Serre, C. (IN2P3, 75 - Paris (France)); Torgersen, H.J. (Oslo Univ. (Norway). Dept. of Chemistry); ISOLDE Collaboration

    1992-08-01

    With the move of the ISOLDE facility to the PS-Booster from the now closed Synchro-Cyclotron at CERN, a new control system will be implented for the two separators. Personal computers, based on the Intel 80386 microprocessor running under MS-DOS and Microsoft Windows, are used. Network-wide distributed front end computers, which access the hardware for controls and measurements, are controlled by PC-consoles via a local area network with a PC file server used as a database. (orig.).

  14. The control system of the CERN-ISOLDE on-line mass-separator facility

    Science.gov (United States)

    Jonsson, O. C.; Borch, O.; Bret, A.; Catherall, R.; Deloose, I.; Focker, G. J.; Forkel, D.; Kugler, E.; Olesen, G.; Pace, A.; Ravn, H. L.; Richard-Serre, C.; Shering, G.; Tengblad, O.; Torgersen, H. J.; Isolde Collaboration

    1992-08-01

    With the move of the ISOLDE facility to the PS-Booster from the now closed Synchro-Cyclotron at CERN, a new control system will be implemented for the two separators. Personal computers, based on the Intel 80386 microprocessor running under MS-DOS and Microsoft Windows, are used. Network-wide distributed front end computers, which access the hardware for controls and measurements, are controlled by PC-consoles via a local area network with a PC file server used as a database.

  15. Stable isotope enrichment techniques and ORNL separation status

    Energy Technology Data Exchange (ETDEWEB)

    Tracy, J.G.; Bell, W.A.; Veach, A.M.; Caudill, H.H.; Milton, H.T.

    1987-05-01

    The isotope separation program is described, emphasizing present state-of-the-art techniques utilized to achieve specific isotopic requirements. An interesting problem addressed here is the calutron enrichment of rare-earth isotopes where small quantities of feed (<5 g) are available, and the unresolved feed is to be recovered and recycled. Conventional ion-source units using graphite and stainless steel deteriorate in the halogenating atmosphere or are permeable to rare-earth compounds, reducing the process efficiency. An ion source has been developed using boron nitride for containing the halogenating agent and rare-earth compounds. Tests have been successfully conducted using Lu/sub 2/O/sub 3/ and the in situ chlorinating technique with CCl/sub 4/. Collectively, 166 mg of /sup 176/Lu were recovered from two runs using 2.95 and 1.10 g of 44.5% /sup 176/Lu. Process efficiency of 10.5% was achieved, and 1.2 g of the unresolved feed were recovered. Material compatibility of the boron nitride, carbon tetrachloride, and lutetium compounds has been established.

  16. Stable isotope enrichment techniques and ORNL separation status

    Science.gov (United States)

    Tracy, J. G.; Bell, W. A.; Veach, A. M.; Caudill, H. H.; Milton, H. T.

    1987-05-01

    The isotope separation program is described, emphasizing present state-of-the-art techniques utilized to achieve specific isotopic requirements. An interesting problem addressed here is the calutron enrichment of rare-earth isotopes where small quantities of feed (< 5 g) are available, and the unresolved feed is to be recovered and recycled. Conventional ion-source units using graphite and stainless steel deteriorate in the halogenating atmosphere or are permeable to rare-earth compounds, reducing the process efficiency. An ion source has been developed using boron nitride for containing the halogenating agent and rare-earth compounds. Tests have been successfully conducted using Lu 2O 3 and the in situ chlorinating technique with CCl 4. Collectively, 166 mg of 176Lu were recovered from two runs using 2.95 and 1.10 g of 44.5% 176Lu. Process efficiency of 10.5% was achieved, and 1.2 g of the unresolved feed were recovered. Material compatibility of the boron nitride, carbon tetrachloride, and lutetium compounds has been established.

  17. On line separation of overlapped signals from multi-time photons for the GEM-based detection system

    Science.gov (United States)

    Czarski, T.; Pozniak, K. T.; Chernyshova, M.; Malinowski, K.; Kasprowicz, G.; Kolasinski, P.; Krawczyk, R.; Wojenski, A.; Zabolotny, W.

    2015-09-01

    The Triple Gas Electron Multiplier (T-GEM) is presented as soft X-ray (SXR) energy and position sensitive detector for high-resolution X-ray diagnostics of magnetic confinement fusion plasmas. Multi-channel measurement system and serial data acquisition for X-ray energy and position recognition is described. Fundamental characteristics are presented for two dimensional detector structure. Typical signals of ADC - Analog to Digital Converter are considered for charge value and position estimation. Coinciding signals for high flux radiation cause the problem for cluster charge identification. The amplifier with shaper determines time characteristics and limits the pulses frequency. Separation of coincided signals was introduced and verified for simulation experiments. On line separation of overlapped signals was implemented applying the FPGA technology with relatively simple firmware procedure. Representative results for reconstruction of coinciding signals are demonstrated.

  18. Isotopic separation by centrifugation. Rotating plasma; Separacion Isotopic por Centrifugacion Plasma Rotante

    Energy Technology Data Exchange (ETDEWEB)

    Perello, M.; Vigon, M. A.

    1972-07-01

    The motion of a gas simultaneously submitted to an electric discharge and magnetic field has been studied in order to analyze the possibility of producing isotopes separation by rotation of a plasma. Some experimental results obtained under different discharge conditions are also given. Differences of pressure up to 15 mm oil between both electrodes has been attained. No definite conclusion on separation factors could be reached because of the low reproducibility of results, probably due to the short duration of the discharge with a new chamber designed to support stronger thermal shocks more reliable data can be expected. (Author) 16 refs.

  19. Isotope Separation and Decay Energy Calculation for LISA Commissioning Experiment

    Science.gov (United States)

    Taylor, Nathaniel; Barker, Alyson; Garrett, Sierra; Rogers, Warren F.; MoNA Collaboration

    2013-10-01

    The commissioning experiment for the Large multi-Institutional Scintillator Array (LISA) was designed to investigate properties of neutron-unstable excited states of the 24O. The array is located at the NSCL, MSU and is used in conjunction with the Modular Neutron Array (MoNA) and the Sweeper Magnet. Oxygen fragments produced by the 26F secondary beam incident on a Be target are directed through the Sweeper Chamber which includes two tracking CRDC detectors, an ion chamber, and a thin and thick scintillator. Plotting the fragment's trajectory position vs. angle vs. time of flight allows for separation of the individual 22 , 23 , and 24 O isotopes, necessary for the calculation of the decay properties of individual states. Anomalous features in the fragments' emittance distribution, believed to result from little understood issues with the tracking detectors, required that we adopt a slightly different approach than that developed recently by the collaboration. Once the isotopes are successfully separated, decay energies are calculated by applying mass-invariant decay spectroscopy by associating the fragment's precise trajectory (determined by inverse-tracking through the Sweeper Magnet) and energy with those of the emitted neutron. Work supported by NSF grant PHY-1101745.

  20. Laser photochemical lead isotopes separation for harmless nuclear power engineering

    Science.gov (United States)

    Bokhan, P. A.; Fateev, N. V.; Kim, V. A.; Zakrevsky, D. E.

    2016-09-01

    The collisional quenching of the metastable 3 P 1,2 and 1 D 2 lead atoms is studied experimentally in the gas flow of the lead atoms, reagent-molecules and a carrier gas Ar. The experimental parameters were similar to the conditions that are required in the operation of the experimental setup for photochemical isotope separation. Excited atoms are generated under electron impact conditions created by a gas glow discharge through the mixture of gases and monitored photoelectrically by attenuation of atomic resonance radiation from hollow cathode 208Pb lamp. The decay of the excited atoms has been studied in the presence various molecules and total cross section data are reported. The flow tube measurements has allowed to separate the physical and chemical quenching channels and measure the rates of the chemical reaction excited lead with N2O, CH2Cl2, SF6 and CuBr molecules. These results are discussed in the prospects of the obtaining isotopically modified lead as a promising coolant in the reactors on the fast-neutron.

  1. Separated isotopes: vital tools for science and medicine

    Energy Technology Data Exchange (ETDEWEB)

    1982-01-01

    Deliberations and conclusions of a Workshop on Stable Isotopes and Derived Radioisotopes organized by the Subcommittee on Nuclear and Radiochemistry of the National Research Council's Committee on Chemical Sciences at the request of the Department of Energy (DOE) are summarized. The workshop was jointly supported by the National Institutes of Health and DOE's Office of Basic Energy Sciences. An overview with three recommendations resulting from the Workshop is followed by reports of the four Workshop panels. Background papers were prepared by individuals on the Steering Committee and made available to all participants prior to the Workshop. They are reproduced as Appendixes 3 to 8. Short reports on alternate separation techniques were presented at the Workshop and are reproduced in Appendixes 9 to 11.

  2. First on-line mass measurements at SHIPTRAP and mass determinations of neutron-rich Fr and Ra isotopes at ISOLTRAP

    CERN Document Server

    Rahaman, Saidu

    SHIPTRAP is an ion trap facility behind the velocity filter SHIP at GSI/Darmstadt. Its aim are precision studies of transuranium nuclides produced in a fusion reaction and separated by SHIP. The current set-up for high-precision mass measurements consists of three main functional parts: (i) a gas cell for stopping the energetic ions from SHIP, (ii) radiofrequency quadrupole structures to cool and to bunch the ions extracted from the gas cell, and (iii) a superconducting magnet with two cylindrical Penning traps at a field strength of 7 T. In this work the Penning trap system has been installed and extensively characterized. The first on-line mass measurements of short-lived nuclides were carried out and the masses of $^{147}$Er and $^{148}$Er could be experimentally determined for the first time. Here a relative mass uncertainty of $\\delta$ m/m of about 1$\\times$ 10$^{-6}$ was achieved. Furthermore the masses of heavy neutron-rich $^{229-232}$Ra and $^{230}$Fr isotopes have been determined with a relative m...

  3. Isotope separation using high-field asymmetric waveform ion mobility spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Barnett, David A.; Purves, Randy W.; Guevremont, Roger E-mail: roger.guevremont@nrc.ca

    2000-08-01

    A new apparatus for gas-phase separation of stable elemental isotopes at atmospheric pressure is described. A gaseous mixture of chloride isotopes was generated using electrospray ionization and introduced into the analyzer region of a high-field asymmetric waveform ion mobility spectrometer (FAIMS). The ion current exiting the FAIMS was sampled into a quadrupole mass spectrometer for isotope identification.

  4. Production of neutron deficient rare isotope beams at IGISOL; on-line and off-line studies

    Energy Technology Data Exchange (ETDEWEB)

    Huikari, J. E-mail: jussi.huikari@phys.jyu.fi; Dendooven, P.; Jokinen, A.; Nieminen, A.; Penttilae, H.; Peraejaervi, K.; Popov, A.; Rinta-Antila, S.; Aeystoe, J

    2004-08-01

    This article reports on recent on-line yield measurements employing the light-ion and heavy-ion reaction-based ion guide systems and new results on {alpha}-recoil ion transport properties in ion guides with and without electric fields. In addition, the presently used ion guide designs for fusion evaporation reactions are introduced. The present study investigated different schemes for ion extraction from the gas cell. The addition of an extra ring electrode between the traditional skimmer electrode and the exit hole led to transmission independent of the primary beam intensity as opposed to strong intensity dependence observed earlier with the plain skimmer only. Furthermore, the mass resolving power of the IGISOL mass separator was increased to 1100 as compared to 250 with the skimmer system when using the RF-sextupole for the extraction from the heavy-ion ion guide. As a new method, the possibility to increase the ion guide efficiency by injecting electrons into the stopping volume is introduced. The efficiency of the electron emitter ion guide was a factor of ten higher in off-line conditions. Also, the influence of the buffer gas purity on the ion survival is discussed.

  5. Highly Efficient Quantum Sieving in Porous Graphene-like Carbon Nitride for Light Isotopes Separation

    Science.gov (United States)

    Qu, Yuanyuan; Li, Feng; Zhou, Hongcai; Zhao, Mingwen

    2016-01-01

    Light isotopes separation, such as 3He/4He, H2/D2, H2/T2, etc., is crucial for various advanced technologies including isotope labeling, nuclear weapons, cryogenics and power generation. However, their nearly identical chemical properties made the separation challenging. The low productivity of the present isotopes separation approaches hinders the relevant applications. An efficient membrane with high performance for isotopes separation is quite appealing. Based on first-principles calculations, we theoretically demonstrated that highly efficient light isotopes separation, such as 3He/4He, can be reached in a porous graphene-like carbon nitride material via quantum sieving effect. Under moderate tensile strain, the quantum sieving of the carbon nitride membrane can be effectively tuned in a continuous way, leading to a temperature window with high 3He/4He selectivity and permeance acceptable for efficient isotopes harvest in industrial application. This mechanism also holds for separation of other light isotopes, such as H2/D2, H2/T2. Such tunable quantum sieving opens a promising avenue for light isotopes separation for industrial application. PMID:26813491

  6. Plasma separation process facility for large-scale stable isotope production

    Energy Technology Data Exchange (ETDEWEB)

    Bigelow, T.S.; Collins, E.D.; Tracy, J.G. [Oak Ridge National Lab., TN (United States)

    1997-12-01

    A facility for large-scale separation of stable isotopes using the plasma separation process (PSP) is under development at the Oak Ridge National Laboratory. The PSP is capable of separating isotopes at a large throughput rate with medium purity product and at relatively low cost. The PSP has a number of convenient features that make it an attractive technology for general isotope separation purposes. Several isotopes for medical and industrial applications, including {sup 102}Pd, {sup 98}Mo, {sup 203}Tl, {sup 184}W, and others, are expected to be processed in this facility. The large throughput and low processing cost of the PSP will likely lead to new applications for stable isotopes. A description of this facility and its typical throughput capability is presented here.

  7. On-line gas chromatography combustion/pyrolysis isotope ratio mass spectrometry (HRGC-C/P-IRMS) of pineapple (Ananas comosus L. Merr.) volatiles.

    Science.gov (United States)

    Preston, Christina; Richling, Elke; Elss, Sandra; Appel, Markus; Heckel, Frank; Hartlieb, Ariane; Schreier, Peter

    2003-12-31

    By use of extracts prepared by liquid-liquid separation of the volatiles from self-prepared juices of pineapple fruits (Ananas comosus) (n = 14) as well as commercial pineapple recovery aromas/water phases (n = 3), on-line capillary gas chromatography-isotope ratio mass spectrometry was employed in the combustion (C) and the pyrolysis (P) modes (HRGC-C/P-IRMS) to determine the delta(13)C(VPDB) and delta(2)H(VSMOW) values of selected pineapple flavor constituents. In addition to methyl 2-methylbutanoate 1, ethyl 2-methylbutanoate 2, methyl hexanoate 3, ethyl hexanoate 4, and 2,5-dimethyl-4-methoxy-3[2H]-furanone 5, each originating from the fruit, the delta(13)C(VPDB) and delta(2)H(VSMOW) data of commercial synthetic 1-5 and "natural" (biotechnologically derived) 1-4 were determined. With delta(13)C(VPDB) data of pineapple volatiles 1-4 varying from -12.8 to -24.4 per thousand, the range expected for CAM metabolism was observed. Compound 5 showed higher depletion from -20.9 to -28.6 per thousand. A similar situation was given for the delta(2)H(VSMOW) values of 3-5 from pineapple ranging from -118 to -191 per thousand, whereas 1 and 2 showed higher depleted values from -184 to -263 per thousand. In nearly all cases, analytical differentiation of 1-5 from pineapple and natural as well as synthetic origin was possible. In general, natural and synthetic 1-5 exhibited delta(13)C(VPDB) data ranging from -11.8 to -32.2 per thousand and -22.7 to -35.9 per thousand, respectively. Their delta(2)H(VSMOW) data were in the range from -242 to -323 per thousand and -49 to -163 per thousand, respectively.

  8. Stable isotope separation in calutrons: Forty years of production and distribution

    Energy Technology Data Exchange (ETDEWEB)

    Bell, W.A.; Tracy, J.G.

    1987-11-01

    The stable isotope separation program, established in 1945, has operated continually to provide enriched stable isotopes and selected radioactive isotopes, including the actinides, for use in research, medicine, and industrial applications. This report summarizes the first forty years of effort in the production and distribution of stable isotopes. Evolution of the program along with the research and development, chemical processing, and production efforts are highlighted. A total of 3.86 million separator hours has been utilized to separate 235 isotopes of 56 elements. Relative effort expended toward processing each of these elements is shown. Collection rates (mg/separator h), which vary by a factor of 20,000 from the highest to the lowest (/sup 205/Tl to /sup 46/Ca), and the attainable isotopic purity for each isotope are presented. Policies related to isotope pricing, isotope distribution, and support for the enrichment program are discussed. Changes in government funding, coupled with large variations in sales revenue, have resulted in 7-fold perturbations in production levels.

  9. Penning-trap Q-value determination of the Ga-71(v, e(-))Ge-71 reaction using threshold charge breeding of on-line produced isotopes

    NARCIS (Netherlands)

    Frekers, D.; Simon, M.C.; Andreoiu, C.; Bale, J. C.; Brodeur, M.; Brunner, T.; Chaudhuri, A.; Chowdhury, U.; Lopez-Urrutia, J. R. Crespo; Delheij, P.; Ejiri, H.; Ettenauer, S.; Gallant, A. T.; Gavrin, V.; Grossheim, A.; Harakeh, M. N.; Jang, F.; Kwiatkowski, A. A.; Lassen, J.; Lennarz, A.; Luichtl, M.; Ma, T.; Macdonald, T. D.; Mane, E.; Robertson, D.; Schultz, B. E.; Simon, V. V.; Teigelhoefer, A.; Dilling, J.

    2013-01-01

    We present a first direct Q-value measurement of the Ga-71(v, e(-))Ge-71 reaction using the TITAN mass-measurement facility at ISAC/TRIUMF. The measurements were performed in a Penning trap on neon-like Ga-71(21+) and Ge-71(22+) using isobar separation of the on-line produced mother and daughter

  10. Penning-trap Q-value determination of the Ga-71(v, e(-))Ge-71 reaction using threshold charge breeding of on-line produced isotopes

    NARCIS (Netherlands)

    Frekers, D.; Simon, M.C.; Andreoiu, C.; Bale, J. C.; Brodeur, M.; Brunner, T.; Chaudhuri, A.; Chowdhury, U.; Lopez-Urrutia, J. R. Crespo; Delheij, P.; Ejiri, H.; Ettenauer, S.; Gallant, A. T.; Gavrin, V.; Grossheim, A.; Harakeh, M. N.; Jang, F.; Kwiatkowski, A. A.; Lassen, J.; Lennarz, A.; Luichtl, M.; Ma, T.; Macdonald, T. D.; Mane, E.; Robertson, D.; Schultz, B. E.; Simon, V. V.; Teigelhoefer, A.; Dilling, J.

    2013-01-01

    We present a first direct Q-value measurement of the Ga-71(v, e(-))Ge-71 reaction using the TITAN mass-measurement facility at ISAC/TRIUMF. The measurements were performed in a Penning trap on neon-like Ga-71(21+) and Ge-71(22+) using isobar separation of the on-line produced mother and daughter nuc

  11. Applications of ion cyclotron-resonance to stable isotope separation; Les applications de la resonance cyclotron ionique a la separation des isotopes stables

    Energy Technology Data Exchange (ETDEWEB)

    Louvet, P.; Metayer, L. [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France). Dept. des Procedes d`Enrichissement

    1994-12-31

    The principles and the technological basic concepts of the ion cyclotron-resonance process applied to the separation of metallic isotopes which mass ranges from 40 to 200 for medical and nuclear applications, are reviewed. The CEA (France) has developed a prototype plant, ERIC; first results showing high separation factors allow to consider higher production in the future. A modular code has been developed (RICAN) in order to assess the technic-economical feasibility of the process for various isotopes; examples of calculated results (costs and production) for calcium 48 and gadolinium 157 production are presented. 4 figs., 1 tab., 4 refs.

  12. Development of On-Line Direct Current Glow Discharge Source for Analysis of Isotope Ratio of Hydrogen

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>The present research is focused on the analysis of isotope ratio of the hydrogen by measuring an intensity ratio of hydrogen/deuterium/tritium fluxes. The direct current glow discharge tube may provide a

  13. The ISOLDE experimental hall, wth the isotope separator in the upper left corner.

    CERN Multimedia

    CERN PhotoLab

    1969-01-01

    Beam tubes branch out from a switchyard, which by electrostatic deflectors direct beams of short-lived isotopes to various spectroscopic equipment. From left to right, Rudi Stoeckli at the separator control panel, Gilbert Droz and Henri Bersinger.

  14. Hydrogen isotope separation by cryogenic distillation: system modelization and design; La separation des isotopes de l`hydrogene par distillation cryogenique: modelisation et conception des installations

    Energy Technology Data Exchange (ETDEWEB)

    Latge, C.; Boisset-Baticle, L.; Buvat, J.C. [CEA Centre d`Etudes de Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. d`Etudes des Reacteurs

    1994-12-31

    The design of fusion reactor systems involves high safety constraints, especially concerning tritium quantity retained in the reactor processes. It is thus necessary to carefully design the separation cascade in order to minimize the tritium inventory. A simulation code has been developed which describes precisely the packed column, based on a mass transfer model and on an automatic optimization procedure for isotopic separation cascades. 4 figs., 5 refs.

  15. Influence of liquid structure on diffusive isotope separation in molten silicates and aqueous solutions

    Science.gov (United States)

    Watkins, James M.; DePaolo, Donald J.; Ryerson, Frederick J.; Peterson, Brook T.

    2011-06-01

    Molecular diffusion in natural volcanic liquids discriminates between isotopes of major ions (e.g., Fe, Mg, Ca, and Li). Although isotope separation by diffusion is expected on theoretical grounds, the dependence on mass is highly variable for different elements and in different media. Silicate liquid diffusion experiments using simple liquid compositions were carried out to further probe the compositional dependence of diffusive isotopic discrimination and its relationship to liquid structure. Two diffusion couples consisting of the mineral constituents anorthite (CaAl 2Si 2O 8; denoted AN), albite (NaAlSi 3O 8; denoted AB), and diopside (CaMgSi 2O 6; denoted DI) were held at 1450 °C for 2 h and then quenched to ambient pressure and temperature. Major-element as well as Ca and Mg isotope profiles were measured on the recovered quenched glasses. In both experiments, Ca diffuses rapidly with respect to Si. In the AB-AN experiment, D Ca/ D Si ≈ 20 and the efficiency of isotope separation for Ca is much greater than in natural liquid experiments where D Ca/ D Si ≈ 1. In the AB-DI experiment, D Ca/ D Si ≈ 6 and the efficiency of isotope separation is between that of the natural liquid experiments and the AB-AN experiment. In the AB-DI experiment, D Mg/ D Si ≈ 1 and the efficiency of isotope separation for Mg is smaller than it is for Ca yet similar to that observed for Mg in natural liquids. The results from the experiments reported here, in combination with results from natural volcanic liquids, show clearly that the efficiency of diffusive separation of Ca isotopes is systematically related to the solvent-normalized diffusivity - the ratio of the diffusivity of the cation ( D Ca) to the diffusivity of silicon ( D Si). The results on Ca isotopes are consistent with available data on Fe, Li, and Mg isotopes in silicate liquids, when considered in terms of the parameter D cation/ D Si. Cations diffusing in aqueous solutions display a similar relationship

  16. Production of high-purity isotopes by electromagnetic separation; Production electromagnetique d'isotope tres purs

    Energy Technology Data Exchange (ETDEWEB)

    Cassignol, Ch. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    Improvement in isotopic purity of nuclides prepared by electromagnetic separation is searched into the principle of cascades of monochromators. The principal drawback of which is to allow the separation of only one isotope at a time. The electromagnetic separator of Saclay is equipped with an electrostatic post-analyzer, which is described. Significant results are obtained, concerning isotopic enhancements of uranium-235 and mercury-204. A schema of isotopic contagion is then proposed, the basis of it is the scattering of the primary ions in the residual atmosphere of the separator chamber. The most frequent type of collisions being accompanied by neutralisation of the ions, the schema explains the efficiency of the second stage. As a matter of conclusion, some particularities concerning the routine work at a high enhancement, small output machine, are given. (author) [French] L'accroissement de la purete isotopique des especes nucleaires preparees par separation electromagnetique est recherche dans l'emploi du principe des cascades de monochromateurs, moyennant la servitude de ne collecter qu'un isotope a la fois. Le separateur electromagnetique de Saclay est equipe dans ce but d'un post-analyseur electrostatique, qui est decrit. Des resultats significatifs sont donnes, portant sur les enrichissements obtenus dans les separations d'uranium-235 et de mercure-204. Un schema de contagion isotopique est propose. Il est fonde sur la diffusion a petit angle accompagnant la neutralisation des faisceaux primaires par collision avec le gaz residuel. Ce schema permet d'expliquer l'efficacite de l'etage electrostatique. En matiere de conclusion, la methode d'exploitation d'une machine a faible debit et a haut enrichissement est donnee. (auteur)

  17. Production of neutron deficient rare isotope beams at IGISOL; on-line and off-line studies

    NARCIS (Netherlands)

    Huikari, J; Dendooven, P; Jokinen, A; Nieminen, A; Penttila, H; Perajarvi, K; Popov, A; Rinta-Antila, S; Aysto, J

    2004-01-01

    This article reports on recent on-line yield measurements employing the light-ion and heavy-ion reaction-based ion guide systems and new results on a-recoil ion transport properties in ion guides with and without electric fields. In addition, the presently used ion guide designs for fusion evaporati

  18. Stable isotope production in the former USSR by electromagnetic separation techniques

    Energy Technology Data Exchange (ETDEWEB)

    Kaschejev, N.A. (Group of Enterprises ' Electrochimpribor' , Ekaterinburg (Russian Federation)); Polyakov, L.A. (Group of Enterprises ' Electrochimpribor' , Ekaterinburg (Russian Federation)); Tunin, V.V. (Group of Enterprises ' Electrochimpribor' , Ekaterinburg (Russian Federation))

    1993-09-15

    The present paper gives a brief review of the status of electromagnetic isotope separation techniques in the former USSR. It describes the basic specifications of the equipment as well as the general scheme of the production process, and considers questions relating to the chemical processing of isotopic material and analytical control technique. Finally, a summary is given of the main separation data obtained during the last ten years, and the prospects of future development and of enhancing the economical effectiveness of isotope production are discussed. (orig.)

  19. Stable isotope production in the former USSR by electromagnetic separation techniques

    Science.gov (United States)

    Kaschejev, N. A.; Polyakov, L. A.; Tunin, V. V.

    1993-09-01

    The present paper gives a brief review of the status of electromagnetic isotope separation techniques in the former USSR. It describes the basic specifications of the equipment as well as the general scheme of the production process, and considers questions relating to the chemical processing of isotopic material and analytical control techniques. Finally, a summary is given of the main separation data obtained during the last ten years, and the prospects of future development and of enhancing the economical effectiveness of isotope production are discussed.

  20. Modelling of mercury isotope separation in CP stellar atmospheres: results and problems

    CERN Document Server

    Sapar, A; Sapar, L; Poolamäe, R; 10.1016/j.newar.2009.08.010

    2009-01-01

    Formation of anomalous isotope abundances in the atmospheres of chemically peculiar (CP) stars can be explained by light-induced drift (LID). This effect is additional to the radiative acceleration and appears due to systematic asymmetry of radiative flux in partly overlapping isotopic spectral line profiles. LID causes levitation of an isotope with a red-shifted spectral line and sinking of an isotope with a blue-shifted line, generating thus diffusive separation of isotopes. We have studied diffusion of mercury as a typical well-studied isotope-rich heavy metal. Our model computations show that in mercury-rich quiescent atmospheres of CP stars LID causes levitation of the heavier mercury isotopes and sinking of the lighter ones. Precise quantitative modelling of the process of isotope separation demands very high-resolution computations and the high-precision input data, including data on hyperfine and isotopic splitting of spectral lines, adequate line profiles and impact cross-sections. Presence of microt...

  1. Pooled versus separate measurements of tree-ring stable isotopes.

    Science.gov (United States)

    Dorado Liñán, Isabel; Gutiérrez, Emilia; Helle, Gerhard; Heinrich, Ingo; Andreu-Hayles, Laia; Planells, Octavi; Leuenberger, Markus; Bürger, Carmen; Schleser, Gerhard

    2011-05-01

    δ(13)C and δ(18)O of tree rings contain time integrated information about the environmental conditions weighted by seasonal growth dynamics and are well established as sources of palaeoclimatic and ecophysiological data. Annually resolved isotope chronologies are frequently produced by pooling dated growth rings from several trees prior to the isotopic analyses. This procedure has the advantage of saving time and resources, but precludes from defining the isotopic error or statistical uncertainty related to the inter-tree variability. Up to now only a few studies have compared isotope series from pooled tree rings with isotopic measurements from individual trees. We tested whether or not the δ(13)C and the δ(18)O chronologies derived from pooled and from individual tree rings display significant differences at two locations from the Iberian Peninsula to assess advantages and constraints of both methodologies. The comparisons along the period 1900-2003 reveal a good agreement between pooled chronologies and the two mean master series which were created by averaging raw individual values (Mean) or by generating a mass calibrated mean (MassC). In most of the cases, pooled chronologies show high synchronicity with averaged individual samples at interannual scale but some differences also show up especially when comparing δ(18)O decadal to multi-decadal variations. Moreover, differences in the first order autocorrelation among individuals may be obscured by pooling strategies. The lack of replication of pooled chronologies prevents detection of a bias due to a higher mass contribution of one sample but uncertainties associated with the analytical process itself, as sample inhomogeneity, seems to account for the observed differences.

  2. Two approaches to hydrograph separation of the glacial river runoff using isotopic methods

    Directory of Open Access Journals (Sweden)

    Yu. N. Chizhova

    2016-01-01

    Full Text Available Application of the stable isotope method in the balance equations used to calculate separation of the runoff hydrograph from the Djankuat Glacier basin is demonstrated. Simultaneous solution of equations of water, isotope and ion balances is applied to estimate contributions of different components and processes to formation of the Djankuat River runoff regime. For June 2014, we made calculations for the purpose to separate contributions of the spring (isotopically weighted snow and winter (isotopically depleted snow. Field works in the glacial basin Djankuat were performed during two ablation seasons, i.e. from June to September of 2013 and 2014. Two approaches were used when calculating separation of the runoff hydrograph by means of solution of systems of equations for isotopic and ion balances: 1 taking account of the isotope fractionation during snow melting, and 2 with no account for the fractionation. Separation of the hydrograph for June 2014 have shown that about 15–20% of the Djankuat River runoff is formed by spring snow melting, sometimes increasing up to 36%. Contribution of spring meltwater to the total runoff increases when the isotope fractionation during the snow melting is taken into account for the calculations. In this case, the contribution of spring snow changes from 30 to 50%.

  3. Status of stable isotopes separation at the Electromagnetic Plants of the Russian Research Center, ``Kurchatov Institute''

    Science.gov (United States)

    Kouzmine, R. N.; Bondarenko, V. G.; Pigarov, Ju. D.; Staroverov, L. I.; Tchesnokov, V. M.

    1999-12-01

    The four chamber electromagnetic isotope separator was constructed at the Russian Research Center (RRC) "Kurchatov Institute" more than 50 years ago. During this period, the plant was used for the development of ion sources and separation technologies. Isotopes of over 40 different elements have been separated. About 20 years ago, the reconstruction of two chambers was completed. The homogeneous magnetic field in these chambers was replaced with a field which falls-off on the radius ( r) as 1/ r. After reconstruction, the dispersion was increased by a factor of four and the enrichment of the isotopes was increased considerably. Ion beam collection was also facilitated. Many highly enriched isotopes were produced in the new chambers, including Gd, Yb, Zn, Tl, Pd, and others. One of the important problems now, is the reduction of all aspects of production costs for isotopes. A project to perfect the ion-optic scheme (IOS) for two chambers was carried out with the expected result of a dispersion of 44 mm at 1% relative mass difference. As a result of the modified ion source, increased productivity of the separators is expected. Other areas of ion source development in progress include: development of "standard" ion sources for the separators with inhomogeneous fields, development of high-temperature sources for Pd isotopes, and development of an ion source with sputtering supply for Ir, Pt, and other elements.

  4. Development of stable isotope separation technology for radioisotope production

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Do Young; Kim, Cheol Jung; Park, Kyung Bae [and others

    2003-05-01

    The ultimate goal of this project is to construct the domestic production system of stable isotopes O-18 and Tl-203 used as target materials in accelerator for the production of medical radioisotopes F-18 and Tl-201, respectively. In order to achieve this goal, diode laser spectroscopic analytical system was constructed and automatic measurement computer software for the direct analysis of H{sub 2}{sup 16}O/H{sub 2}{sup 18}O ratio were developed. Distillation process, laser process, and membrane diffusion process were analyzed for the evaluation of O-18 production. And electromagnetic process, plasma process, and laser process were analyzed for the evaluation of Tl-203 production. UV laser system, IR laser system, and detailed system Tl-203 production were designed. Finally, current and future worldwide demand/supply of stable isotopes O-18 and Tl-203 were estimated.

  5. On-line hydrogen-isotope measurements of organic samples using elemental chromium: An extension for high temperature elemental-analyzer techniques

    Science.gov (United States)

    Gehre, Matthias; Renpenning, Julian; Gilevska, Tetyana; Qi, Haiping; Coplen, Tyler B.; Meijer, Harro A.J.; Brand, Willi A.; Schimmelmann, Arndt

    2015-01-01

    The high temperature conversion (HTC) technique using an elemental analyzer with a glassy carbon tube and filling (temperature conversion/elemental analysis, TC/EA) is a widely used method for hydrogen isotopic analysis of water and many solid and liquid organic samples with analysis by isotope-ratio mass spectrometry (IRMS). However, the TC/EA IRMS method may produce inaccurate δ2H results, with values deviating by more than 20 mUr (milliurey = 0.001 = 1‰) from the true value for some materials. We show that a single-oven, chromium-filled elemental analyzer coupled to an IRMS substantially improves the measurement quality and reliability for hydrogen isotopic compositions of organic substances (Cr-EA method). Hot chromium maximizes the yield of molecular hydrogen in a helium carrier gas by irreversibly and quantitatively scavenging all reactive elements except hydrogen. In contrast, under TC/EA conditions, heteroelements like nitrogen or chlorine (and other halogens) can form hydrogen cyanide (HCN) or hydrogen chloride (HCl) and this can cause isotopic fractionation. The Cr-EA technique thus expands the analytical possibilities for on-line hydrogen-isotope measurements of organic samples significantly. This method yielded reproducibility values (1-sigma) for δ2H measurements on water and caffeine samples of better than 1.0 and 0.5 mUr, respectively. To overcome handling problems with water as the principal calibration anchor for hydrogen isotopic measurements, we have employed an effective and simple strategy using reference waters or other liquids sealed in silver-tube segments. These crimped silver tubes can be employed in both the Cr-EA and TC/EA techniques. They simplify considerably the normalization of hydrogen-isotope measurement data to the VSMOW-SLAP (Vienna Standard Mean Ocean Water-Standard Light Antarctic Precipitation) scale, and their use improves accuracy of the data by eliminating evaporative loss and associated isotopic fractionation while

  6. Recent progress of in-flight separators and rare isotope beam production

    Energy Technology Data Exchange (ETDEWEB)

    Kubo, Toshiyuki, E-mail: kubo@ribf.riken.jp

    2016-06-01

    New-generation in-flight separators are being developed worldwide, including the Super-FRS separator at the GSI Facility for Antiproton and Ion Research (FAIR), the ARIS separator at the Michigan State University (MSU) Facility for Rare Isotopes Beams (FRIB), and the BigRIPS separator at the RIKEN RI Beam Factory (RIBF), each of which is aimed at expanding the frontiers of rare isotope (RI) production and advancing experimental studies on exotic nuclei far from stability. Here, the recent progress of in-flight separators is reviewed, focusing on the advanced features of these three representative separators. The RI beam production that we have conducted using the BigRIPS separator at RIKEN RIBF is also outlined.

  7. Pooled versus separate measurements of tree-ring stable isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Dorado Linan, Isabel, E-mail: isabel@gfz-potsdam.de [Universitat de Barcelona, Departament d' Ecologia, Diagonal 645, 08028, Barcelona (Spain); German Centre for Geosciences, Climate Dynamics and Landscape Evolution, Dendro Laboratory, Telegrafenberg, 14473, Potsdam (Germany); Gutierrez, Emilia, E-mail: emgutierrez@ub.edu [Universitat de Barcelona, Departament d' Ecologia, Diagonal 645, 08028, Barcelona (Spain); Helle, Gerhard, E-mail: ghelle@gfz-potsdam.de [German Centre for Geosciences, Climate Dynamics and Landscape Evolution, Dendro Laboratory, Telegrafenberg, 14473, Potsdam (Germany); Heinrich, Ingo, E-mail: heinrich@gfz-potsdam.de [German Centre for Geosciences, Climate Dynamics and Landscape Evolution, Dendro Laboratory, Telegrafenberg, 14473, Potsdam (Germany); Andreu-Hayles, Laia, E-mail: laiandreu@ub.edu [Universitat de Barcelona, Departament d' Ecologia, Diagonal 645, 08028, Barcelona (Spain); Tree-Ring Laboratory, Lamont-Doherty Earth Observatory of Columbia University, Palisades NY (United States); Planells, Octavi, E-mail: leocarpus@hotmail.com [Universitat de Barcelona, Departament d' Ecologia, Diagonal 645, 08028, Barcelona (Spain); Leuenberger, Markus, E-mail: leuenberger@climate.unibe.ch [Climate and Environmental Physics, Physics Institute, University of Bern, Sidlerstrasse 5, 3012 Bern (Switzerland); Oeschger Centre of Climate Change Research, University of Bern, Zaehringerstrasse 25, 3012 Bern (Switzerland); Buerger, Carmen, E-mail: buerger@gfz-potsdam.de [German Centre for Geosciences, Climate Dynamics and Landscape Evolution, Dendro Laboratory, Telegrafenberg, 14473, Potsdam (Germany); Schleser, Gerhard, E-mail: schleser@gfz-potsdam.de [German Centre for Geosciences, Climate Dynamics and Landscape Evolution, Dendro Laboratory, Telegrafenberg, 14473, Potsdam (Germany)

    2011-05-01

    {delta}{sup 13}C and {delta}{sup 18}O of tree rings contain time integrated information about the environmental conditions weighted by seasonal growth dynamics and are well established as sources of palaeoclimatic and ecophysiological data. Annually resolved isotope chronologies are frequently produced by pooling dated growth rings from several trees prior to the isotopic analyses. This procedure has the advantage of saving time and resources, but precludes from defining the isotopic error or statistical uncertainty related to the inter-tree variability. Up to now only a few studies have compared isotope series from pooled tree rings with isotopic measurements from individual trees. We tested whether or not the {delta}{sup 13}C and the {delta}{sup 18}O chronologies derived from pooled and from individual tree rings display significant differences at two locations from the Iberian Peninsula to assess advantages and constraints of both methodologies. The comparisons along the period 1900-2003 reveal a good agreement between pooled chronologies and the two mean master series which were created by averaging raw individual values (Mean) or by generating a mass calibrated mean (MassC). In most of the cases, pooled chronologies show high synchronicity with averaged individual samples at interannual scale but some differences also show up especially when comparing {delta}{sup 18}O decadal to multi-decadal variations. Moreover, differences in the first order autocorrelation among individuals may be obscured by pooling strategies. The lack of replication of pooled chronologies prevents detection of a bias due to a higher mass contribution of one sample but uncertainties associated with the analytical process itself, as sample inhomogeneity, seems to account for the observed differences. - Research Highlights: {yields} Pooled {delta}{sup 13}C and {delta}{sup 18}O chronologies are expected to be similar to the mean. {yields} Empirical pooled chronologies {delta}{sup 13}C and

  8. Isotopic separation through ion cyclotron-resonance: results from the ERIC experiment; La separation isotopique par resonance cyclotron ionique: resultats obtenus avec l`experience ERIC

    Energy Technology Data Exchange (ETDEWEB)

    Compant la Fontaine, A.; Louvet, P. [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France). Dept. des Procedes d`Enrichissement

    1994-12-31

    Stable isotope separation by the means of ion cyclotron-resonance is studied at CEA since 1981. Results from the ERIC experiments are of two types: parameter measurements which help characterizing the plasma and optimizing the process, and isotopic separation results. For example, the selective feature of isotope heating was verified in the cases of zinc and calcium using an electrostatic analyzer. The separation factors of various elements (calcium, zinc, barium, chromium...) are depending on the mass relative difference of the isotopes to be separated, difference which must be large compared to the magnetic field inhomogeneities and the Doppler broadening. 2 figs., 1 tab., 3 refs.

  9. Development of the Separation System of {sup 203}Tl Stable Isotope

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Do Young; Ko, Kwang Hoon; Lim, Gwon; Kim, Tak Soo; Park, Hyun Min; Rho, Si Pyo; Kim, Cheol Jung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2005-07-01

    Thallium has two naturally occurring isotopes, {sup 203}Tl and {sup 205}Tl, with abundances of 30% and 70%, respectively. {sup 203}Tl is an indispensable raw material for the production of {sup 201}Tl radioisotopes by a proton bombardment in a cyclotron. {sup 201}TlCl is a radiopharmaceutical used widely to diagnose a heart disease. Development of the isotope-selective photoionization technique of Tl has been attractive, but an isotope selective ionization of thallium has never been achieved so far because of its small isotope shift as well as the lack of an available autoionization state. We have proposed a new method to separate the thallium isotopes, which is based-on an isotope-selective optical pumping followed by infrared photoionization. Many photoionization methods are available, such as the two photon excitation followed by the direct ionization in a high electric field. But, other ionization methods do not have the sufficient selectivity for a single stage. Two or three stages have to be applied for obtaining the sufficient selectivity. Moreover, they need strict experimental conditions and are expected that the efficiency decreases in the ionization step. However, our method is expected to overcome these drawbacks. With this background, we developed the laser isotope separation system to have high isotopic abundance of {sup 203}Tl. The system configuration and characteristics are represented in this paper.

  10. National uses and needs for separated stable isotopes in physics, chemistry, and geoscience research

    Science.gov (United States)

    Zisman, M. S.

    Present uses of separated stable isotopes in the fields of physics, chemistry, and the geosciences were surveyed to identify current supply problems and to determine future needs. Demand for separated isotopes remains strong, with 220 different nuclides having been used in the past three years. The largest needs, in terms of both quantity and variety of isotopes, are found in nuclear physics research. Current problems include a lack of availability of many nuclides, unsatisfactory enrichment of rare species, and prohibitively high costs for certain important isotopes. Demand for separated isotopes is expected to remain roughly at present levels, although a shift toward more requests for highly enriched rare isotopes is predicted. Use of neutron rich nuclides below A = 100 for producing exotic ion beams at various accelerators and use of transition metal nuclei for nuclear magnetic resonance spectroscopy are expected to expand. An increase in the need for calibration standards for techniques of radiological dating, such as Sm/Nd and Lu/Hf is predicted, but in relatively small quantities. Most members of the research community would be willing to pay considerably more than they do now to maintain adequate supplies of stable isotopes.

  11. National uses and needs for separated stable isotopes in physics, chemistry, and geoscience research

    Energy Technology Data Exchange (ETDEWEB)

    Zisman, M.S.

    1982-01-01

    Present uses of separated stable isotopes in the fields of physics, chemistry, and the geosciences have been surveyed to identify current supply problems and to determine future needs. Demand for separated isotopes remains strong, with 220 different nuclides having been used in the past three years. The largest needs, in terms of both quantity and variety of isotopes, are found in nuclear physics research. Current problems include a lack of availability of many nuclides, unsatisfactory enrichment of rare species, and prohibitively high costs for certain important isotopes. It is expected that demands for separated isotopes will remain roughly at present levels, although there will be a shift toward more requests for highly enriched rare isotopes. Significantly greater use will be made of neutron-rich nuclides below A = 100 for producing exotic ion beams at various accelerators. Use of transition metal nuclei for nuclear magnetic resonance spectroscopy will expand. In addition, calibration standards will be required for the newer techniques of radiological dating, such as the Sm/Nd and Lu/Hf methods, but in relatively small quantities. Most members of the research community would be willing to pay considerably more than they do now to maintain adequate supplies of stable isotopes.

  12. Nested reactor chamber and operation for Hg-196 isotope separation process

    Science.gov (United States)

    Grossman, M.W.

    1991-10-08

    The present invention is directed to an apparatus for use in [sup 196]Hg separation and its method of operation. Specifically, the present invention is directed to a nested reactor chamber useful for [sup 196]Hg isotope separation reactions avoiding the photon starved condition commonly encountered in coaxial reactor systems. 6 figures.

  13. Electromagnetic separation of stable isotopes at the Institute of Atomic Energy, Academia Sinica

    Science.gov (United States)

    Ming-da, Hua; Gong-pan, Li; Shi-jun, Su; Nai-feng, Mao; Hung-yung, Lu

    1981-07-01

    For almost 20 years the Institute of Atomic Energy, Academia Sinica has been separating stable isotopes of the elements by electromagnetic separators and supplying these materials to research work in many fields of our country. In this article we shall attempt to outline the growth of the effort and describe the present situation.

  14. Separation of selected stable isotopes by liquid-phase thermal diffusion and by chemical exchange

    Science.gov (United States)

    Rutherford, W. M.; Jepson, B. E.; Michaels, E. D.

    Useful applications of enriched stable nuclides are unduly restricted by high cost and limited availability. Recent research on liquid phase thermal diffusion (LTD) has resulted in practical processes for separating S34, CL35, and CL37 in significant quantities (100 to 500 g/yr) at costs much lower than those associated with the electromagnetic (Calutron) process. The separation of the isotopes of bromine by LTD is now in progress and BR79 is being produced in relatively simple equivalent at a rate on the order of 0.5 g/day. The results of recent measurements show that the isotopes of Zn can be separated by LTD of zinc alkyls. The isotopes of calcium can be separated by LTD and by chemical exchange. The LTD process is based on the use of aqueous Ca(NO3)2 as a working fluid.

  15. The quantum and mechanical justification of intensification by magnetic field of amalgam isotope separation method

    Directory of Open Access Journals (Sweden)

    Myshkin V. F.

    2015-09-01

    Full Text Available The steady increase in demand for isotopes requires the development of methods to increase the efficiency of isotope separation technologies. Methods of isotope separation based on thermodynamic differences of isotopic forms of the molecules don't require significant investment, but characterized by a low rate of exchange. It's known that the magnetic effect leads to a change the vibrational frequency of the molecules, and therefore their thermodynamic parameters. The change increases the thermodynamic parameters, including the exchange rate. The results of the experimental determination of the thermal effect of dissolving the salts of NaCl, KCl, CuSO4, sodium amalgam decomposition by distillate in a magnetic field and without field were shown. Magnetic interference can have a significant effect on the amalgam exchange method which was shown by quantum and mechanical analysis of the results

  16. Chromatographic separation process with pellicular ion exchange resins that can be used for ion or isotope separation and resins used in this process. Procede de separation chromatographique au moyen de resines echangeuses d'ions pelliculaires, utilisable notamment pour la separation des isotopes ou des ions, et resines utilisables dans ce procede

    Energy Technology Data Exchange (ETDEWEB)

    Carles, M.; Neige, R.; Niemann, C.; Michel, A.; Bert, M.; Bodrero, S.; Guyot, A.

    1989-01-06

    For separation of uranium, boron or nitrogen isotopes, an isotopic exchange is carried out betwen an isotope fixed on an ion exchange resin and another isotope of the same element in the liquid phase contacting the resin. Pellicular resins are used comprising composite particulates with an inert polymeric core and a surface layer with ion exchange groups.

  17. Separation and Analysis of Boron Isotope in High Plant by Thermal Ionization Mass Spectrometry

    Directory of Open Access Journals (Sweden)

    Qingcai Xu

    2015-01-01

    Full Text Available Knowledge of boron and its isotope in plants is useful to better understand the transposition and translocation of boron within plant, the geochemical behavior in the interface between soil and plant, and the biogeochemical cycle of boron. It is critical to develop a useful method to separate boron from the plant for the geochemical application of boron and its isotope. A method was developed for the extraction of boron in plant sample, whose isotope was determined by thermal ionization mass spectrometry. The results indicated that this method of dry ashing coupled with two-step ion-exchange chromatography is powerful for the separation of boron in plant sample with large amounts of organic matters completely. The ratios of boron isotope composition in those plant tissue samples ranged from -19.45‰ to +28.13‰ (total range: 47.58‰ with a mean value of 2.61±11.76‰ SD. The stem and root isotopic compositions were lower than those in flower and leaf. The molecular mechanism of boron isotope may be responsible for the observed variation of boron isotopic composition and are considered as a useful tool for the better understanding of boron cycling process in the environment and for the signature of living systems.

  18. Separation of hydrogen isotopes from nitrogen with polyimide membrane

    Energy Technology Data Exchange (ETDEWEB)

    Labrune, D.; Limacher, B.; Guidon, H. [Commissariat a l`Energie Atomique, Bruyeres-le-Chatel (France); Moll, G. [Societe Generale des Techniques Nouvelles, Saint Quentin Yvelines (France)

    1995-10-01

    Gas separation tests were performed with nitrogen containing small concentrations of deuterium or tritium on a small-scale polyimide membrane module purchased from Ube Industries, similar to that developed at the Japan Atomic Energy Research Institute (JAERI). Experimental results showed that this separation process could be potentially applied to tritium removal systems used in tritium handling facilities. It would permit reducing significantly the gas volume to be treated by the conventional oxidation-adsorption process, and, therefore, the number or size of associated equipment. Hazards from handling highly toxic tritiated water vapor due to conversion of elemental tritium would hence be lowered. 3 refs., 10 figs., 1 tab.

  19. Lithium isotopic separation: preliminary studies; Separacao isotopica de litio: estudos preliminares

    Energy Technology Data Exchange (ETDEWEB)

    Macedo, Sandra Helena Goulart de

    1998-07-01

    In order to get the separation of natural isotopes of lithium by electrolytic amalgamation, an electrolytic cell with a confined mercury cathode was used to obtain data for the design of a separation stage. The initial work was followed by the design of a moving mercury cathode electrolytic cell and three experiments with six batches stages were performed for the determination of the elementary separation factor. The value obtained, 1.053, was ill agreement: with the specialized literature. It was verified in all experiments that the lithium - 6 isotope concentrated in the amalgam phase and that the lithium - 7 isotope concentrated in the aqueous phase. A stainless-steel cathode for the decomposition of the lithium amalgam and the selective desamalgamation were also studied. In view of the results obtained, a five stages continuous scheme was proposed. (author)

  20. Separation of proteins by zone electrophoresis on-line coupled with isotachophoresis on a column-coupling chip with conductivity detection.

    Science.gov (United States)

    Olvecká, Eva; Kaniansky, Dusan; Pollák, Branislav; Stanislawski, Bernd

    2004-11-01

    This feasibility study deals with the separations of proteins by an on-line combination of zone electrophoresis (ZE) with isotachophoresis (ITP) on a poly(methylmethacrylate) column-coupling (CC) chip with integrated conductivity detection. ITP and ZE provided specific analytical functions while performing the cationic mode of the separation. ITP served, mainly, for concentrations of proteins and its concentrating power was beneficial in reaching a low dispersion transfer (injection) of the proteinous constituents, loaded on the CC chip in a 960 nL volume, into the ZE separation stage. This was complemented by an electrophoretically driven removal of the sample constituents migrating in front of the focused proteins from the separation system before the ZE separation. On the other hand, ZE served as a final separation (destacking) method and it was used under the separating conditions providing the resolutions and sensitive conductivity detections of the test proteins. In this way, ITP and ZE cooperatively contributed to low- or sub-microg/mL concentration detectabilities of proteins and their quantitations at 1-5 microg/mL concentrations. However, a full benefit in concentration detectabilities of proteins, expected from the use of the ITP-ZE combination, was not reached in this work. Small adsorption losses of proteins and detection disturbances in the ZE stage of separation, very likely due to trace constituents concentrated by ITP, appear to set limits in the detection of proteins in our experiments. The ITP-ZE separations were carried out in a hydrodynamically closed separation compartment of the chip with suppressed hydrodynamic and electroosmotic flows of the electrolyte solutions. Such transport conditions, minimizing fluctuations of the migration velocities of the separated constituents, undoubtedly contributed to highly reproducible migrations of the separated proteins (fluctuations of the migration time of a particular protein were typically 0.5% RSD in

  1. High efficiency noble gas electron impact ion source for isotope separation

    Energy Technology Data Exchange (ETDEWEB)

    Appelhans, A. D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Olson, J. E. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Dahl, D. A. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Ward, M. B. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-07-01

    An electron impact ion source has been designed for generation of noble gas ions in a compact isotope separator. The source utilizes a circular filament that surrounds an ionization chamber, enabling multiple passes of electrons through the ionization chamber. This report presents ion optical design and the results of efficiency and sensitivity measurements performed in an ion source test chamber and in the compact isotope separator. The cylindrical design produced xenon ions at an efficiency of 0.37% with a sensitivity of ~24 µA /Pa at 300 µA of electron current.

  2. High-pressure continuously tunable CO2 lasers and molecular laser isotope separation

    Indian Academy of Sciences (India)

    E Ronander; H J Strydom; L R Botha

    2014-01-01

    The acronym MLIS (molecular laser isotope separation) defines the laser process whereby the isotopes of uranium can be separated by mid-infrared laser/s when the molecule employed is UF6. The theoretical and spectroscopical data to configure and enable experiments and demonstrations in the laboratory is adequate. However, the engineering and commercial aspects require innovative technology solutions that are not presently available in the literature on these topics. This paper is an overview of the most salient features of MLIS and its potential utility at an industrial level.

  3. A Model of Isotope Separation in Cells at the Early Stages of Evolution.

    Science.gov (United States)

    Melkikh, A V; Bokunyaeva, A O

    2016-03-01

    The separation of the isotopes of certain ions can serve as an important criterion for the presence of life in the early stages of its evolution. A model of the separation of isotopes during their transport through the cell membrane is constructed. The dependence of the selection coefficient on various parameters is found. In particular, it is shown that the maximum efficiency of the transport of ions corresponds to the minimum enrichment coefficient. At the maximum enrichment, the efficiency of the transport system approaches ½. Calculated enrichment coefficients are compared with experimentally obtained values for different types of cells, and the comparison shows a qualitative agreement between these quantities.

  4. Multi-purpose hydrogen isotopes separation plant design

    Energy Technology Data Exchange (ETDEWEB)

    Boniface, H.A.; Gnanapragasam, N.V.; Ryland, D.K.; Suppiah, S.; Castillo, I. [Atomic Energy of Canada Limited - AECL, Chalk River, ON (Canada)

    2015-03-15

    There is a potential interest at AECL's Chalk River Laboratories to remove tritium from moderately tritiated light water and to reclaim tritiated, downgraded heavy water. With only a few limitations, a single CECE (Combined Electrolysis and Catalytic Exchange) process configuration can be designed to remove tritium from heavy water or light water and upgrade heavy water. Such a design would have some restrictions on the nature of the feed-stock and tritium product, but could produce essentially tritium-free light or heavy water that is chemically pure. The extracted tritium is produced as a small quantity of tritiated heavy water. The overall plant capacity is fixed by the total amount of electrolysis and volume of catalyst. In this proposal, with 60 kA of electrolysis a throughput of 15 kg*h{sup -1} light water for detritiation, about 4 kg*h{sup -1} of heavy water for detritiation and about 27 kg*h{sup -1} of 98% heavy water for upgrading can be processed. Such a plant requires about 1,000 liters of AECL isotope exchange catalyst. The general design features and details of this multi-purpose CECE process are described in this paper, based on some practical choices of design criteria. In addition, we outline the small differences that must be accommodated and some compromises that must be made to make the plant capable of such flexible operation. (authors)

  5. Determination of lycopene in food by on-line SFE coupled to HPLC using a single monolithic column for trapping and separation.

    Science.gov (United States)

    Pól, Jaroslav; Hyötylänen, Tuulia; Ranta-Aho, Outi; Riekkola, Marja-Liisa

    2004-10-15

    A method that would eliminate the degradation of lycopene during analysis was developed. Supercritical fluid extraction (SFE) with carbon dioxide as the extraction medium was connected on-line to high performance liquid chromatography (HPLC) where a single monolithic column was used for trapping and the subsequent separation of analytes. The method was linear over the studied range (0.1-2.5 microg), and it was repeatable (R.S.D. 3.9%), sensitive (LOD = 0.5 ng) and fast (35 min). Lycopene was determined in tomatoes, fruit and several food products. Because of the on-line construction, lycopene was not in contact with air or light during the whole procedure and the amount analysed should therefore correspond to the real amount in the sample.

  6. [On-line method for measurement of the carbon isotope ratio of atmospheric methane and its application to atmosphere of Yakela condensed gas field].

    Science.gov (United States)

    Tang, Jun-Hong; Bao, Zheng-Yu; Xiang, Wu; Qiao, Sheng-Ying; Li, Bing

    2006-01-01

    An on-line method for measurement of the 13C/12C ratio of methane by a gas chromatography/high-temperature conversion/ isotope ratio mass spectrometry (GC/C/MS) technique was developed. This method is less laborious, more rapid (45 min), of high precision (+/- 0.4 x 10(-3)) and by using a small amount of sample (about 200 mL of atmosphere). Its application to isotopic characterization, and hence methane source identification, was demonstrated by examination of atmosphere sample collected in Yakela condensed gas field, China. The average 13C/12C ratio of atmospheric methane in Yakela field was -45.0 x 10(-3) heavier by 1.2 x 10(-3) -2.0 x 10(-3) than the global average. This is caused by seepage and diffusing of methane from Yakela condensed gas reservoir. The concentrations of atmospheric methane in daytimes are found to be lower than those in nighttimes, and the corresponding 13C/12C ratios in daytimes are lighter compared to those in nighttimes, a phenomena probably caused by the fact that a small part of methane from Yakela condensate reservoir is consumed in soil's surface under sunlight.

  7. Influence of liquid structure on diffusive isotope separation in molten silicates and aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Watkins, J.M.; DePaolo, D.J.; Ryerson, F.J.; Peterson, B.

    2011-03-01

    Molecular diffusion in natural volcanic liquids discriminates between isotopes of major ions (e.g., Fe, Mg, Ca, and Li). Although isotope separation by diffusion is expected on theoretical grounds, the dependence on mass is highly variable for different elements and in different media. Silicate liquid diffusion experiments using simple liquid compositions were carried out to further probe the compositional dependence of diffusive isotopic discrimination and its relationship to liquid structure. Two diffusion couples consisting of the mineral constituents anorthite (CaAl{sub 2}Si{sub 2}O{sub 8}; denoted AN), albite (NaAlSi{sub 3}O{sub 8}; denoted AB), and diopside (CaMgSi{sub 2}O{sub 6}; denoted DI) were held at 1450°C for 2 h and then quenched to ambient pressure and temperature. Major-element as well as Ca and Mg isotope profiles were measured on the recovered quenched glasses. In both experiments, Ca diffuses rapidly with respect to Si. In the AB–AN experiment, D{sub Ca}/D{sub Si} ~ 20 and the efficiency of isotope separation for Ca is much greater than in natural liquid experiments where D{sub Ca}/D{sub Si} ~ 1. In the AB–DI experiment, D{sub Ca}/D{sub Si} ~ 6 and the efficiency of isotope separation is between that of the natural liquid experiments and the AB–AN experiment. In the AB–DI experiment, D{sub Mg}/D{sub Si} ~ 1 and the efficiency of isotope separation for Mg is smaller than it is for Ca yet similar to that observed for Mg in natural liquids. The results from the experiments reported here, in combination with results from natural volcanic liquids, show clearly that the efficiency of diffusive separation of Ca isotopes is systematically related to the solvent-normalized diffusivity—the ratio of the diffusivity of the cation (D{sub Ca}) to the diffusivity of silicon (D{sub Si}). The results on Ca isotopes are consistent with available data on Fe, Li, and Mg isotopes in silicate liquids, when considered in terms of the parameter D{sub cation

  8. Stable Isotope Quantitative N-Glycan Analysis by Liquid Separation Techniques and Mass Spectrometry.

    Science.gov (United States)

    Mittermayr, Stefan; Albrecht, Simone; Váradi, Csaba; Millán-Martín, Silvia; Bones, Jonathan

    2017-01-01

    Liquid phase separation analysis and subsequent quantitation remains a challenging task for protein-derived oligosaccharides due to their inherent structural complexity and diversity. Incomplete resolution or co-detection of multiple glycan species complicates peak area-based quantitation and associated statistical analysis when optical detection methods are used. The approach outlined herein describes the utilization of stable isotope variants of commonly used fluorescent tags that allow for mass-based glycan identification and relative quantitation following separation by liquid chromatography (LC) or capillary electrophoresis (CE). Comparability assessment of glycoprotein-derived oligosaccharides is performed by derivatization with commercially available isotope variants of 2-aminobenzoic acid or aniline and analysis by LC- and CE-mass spectrometry. Quantitative information is attained from the extracted ion chromatogram/electropherogram ratios generated from the light and heavy isotope clusters.

  9. Exploiting Diffusion Barrier and Chemical Affinity of Metal-Organic Frameworks for Efficient Hydrogen Isotope Separation.

    Science.gov (United States)

    Kim, Jin Yeong; Balderas-Xicohtencatl, Rafael; Zhang, Linda; Kang, Sung Gu; Hirscher, Michael; Oh, Hyunchul; Moon, Hoi Ri

    2017-09-23

    Deuterium plays a pivotal role in industrial and scientific research, and is irreplaceable for various applications such as isotope tracing, neutron moderation, and neutron scattering. In addition, deuterium is a key energy source for fusion reactions. Thus, the isolation of deuterium from physico-chemically almost identical isotopic mixture is a seminal challenge in modern separation technology. However, current commercial approaches suffer from extremely low separation efficiency (i.e. cryogenic distillation, selectivity of 1.5 at 24 K), requiring a cost-effective and large-scale separation technique. Herein, we report a highly effective hydrogen isotope separation system based on metal-organic frameworks (MOFs) having the highest reported separation factor as high as ~26 at 77 K by maximizing synergistic effects of the chemical affinity quantum sieving (CAQS) and kinetic quantum sieving (KQS). For this purpose, MOF-74 system having high hydrogen adsorption enthalpies due to strong open metal sites is chosen for CAQS functionality and imidazole molecules (IM) are employed to the system for enhancing the KQS effect. To the best of our knowledge, this work is not only the first attempt to implement two quantum sieving effects, KQS and CAQS, in one system but also provides experimental validation of the utility of this system for practical industrial usage by isolating high-purity D2 through direct selective separation studies using 1:1 D2/H2 mixtures.

  10. Separation of copper, iron, and zinc from complex aqueous solutions for isotopic measurement

    Science.gov (United States)

    Borrok, D.M.; Wanty, R.B.; Ridley, W.I.; Wolf, R.; Lamothe, P.J.; Adams, M.

    2007-01-01

    The measurement of Cu, Fe, and Zn isotopes in natural samples may provide valuable information about biogeochemical processes in the environment. However, the widespread application of stable Cu, Fe, and Zn isotope chemistry to natural water systems remains limited by our ability to efficiently separate these trace elements from the greater concentrations of matrix elements. In this study, we present a new method for the isolation of Cu, Fe, and Zn from complex aqueous solutions using a single anion-exchange column with hydrochloric acid media. Using this method we are able to quantitatively separate Cu, Fe, and Zn from each other and from matrix elements in a single column elution. Elution of the elements of interest, as well as all other elements, through the anion-exchange column is a function of the speciation of each element in the various concentrations of HCl. We highlight the column chemistry by comparing our observations with published studies that have investigated the speciation of Cu, Fe, and Zn in chloride solutions. The functionality of the column procedure was tested by measuring Cu, Fe, and Zn isotopes in a variety of stream water samples impacted by acid mine drainage. The accuracy and precision of Zn isotopic measurements was tested by doping Zn-free stream water with the Zn isotopic standard. The reproducibility of the entire column separation process and the overall precision of the isotopic measurements were also evaluated. The isotopic results demonstrate that the Cu, Fe, and Zn column separates from the tested stream waters are of sufficient purity to be analyzed directly using a multicollector inductively coupled plasma mass spectrometer (MC-ICP-MS), and that the measurements are fully-reproducible, accurate, and precise. Although limited in scope, these isotopic measurements reveal significant variations in ??65Cu (- 1.41 to + 0.30???), ??56Fe (- 0.56 to + 0.34???), and ??66Zn (0.31 to 0.49???) among samples collected from different

  11. Application and recovery of ionic liquids in the preparative separation of four flavonoids from Rhodiola rosea by on-line three-dimensional liquid chromatography.

    Science.gov (United States)

    Ma, Shufeng; Hu, Liming; Ma, Chaoyang; Lv, Wenping; Wang, Hongxin

    2014-09-01

    A novel on-line three-dimensional liquid chromatography method was developed to separate four main flavonoids from Rhodiola rosea. Ethyl acetate/0.5 mol/L ionic liquid 1-butyl-3-methylimidazolium chloride aqueous solution was selected as the solvent system. In the first-dimension separation, the target flavonoids were entrapped and subsequently desorbed into the second-dimension high-speed countercurrent chromatographic column for separation. In the third-dimension chromatography, the residual ionic liquid in the four separated flavonoids was removed and the used ionic liquid was recovered. As a result, 35.1 mg of compound 1, 20.4 mg of compound 2, 8.5 mg of compound 3, and 10.6 mg of compound 4 were obtained from 1.53 g R. rosea extract. They were identified as rhodiosin, rhodionin, herbacetin, and kaempferol, respectively. The recovery of ionic liquid reached 99.1% of the initial amount. The results showed that this method is a powerful technology for the separation of R. rosea flavonoids and that the ionic-liquid-based solvent system has advantages over traditional solvent systems in renewable and environmentally friendly properties.

  12. Laser isotope separation by selective excited state photochemistry. Annual progress report, March 31, 1976--February 28, 1977

    Energy Technology Data Exchange (ETDEWEB)

    Zare, R.N.

    1977-03-01

    Experimental results are presented providing insight into the mechanisms of photochemical separation of Cd isotopes by selective excitation of ICl in the presence of halogenated olefins. The types of scrambling reactions that can be expected in isotope separation by scavenging are discussed along with strategies for minimizing such reactions. The experimental results are summarized and the reaction mechanisms are represented by graphic equations. (JRD)

  13. Startup and Operation of a Metal Hydride Based Isotope Separation Process

    Energy Technology Data Exchange (ETDEWEB)

    Scogin, J.H.; Poore, A.S.

    1995-02-27

    Production scale separation of tritium from other hydrogen isotopes at the Savannah River Site (SRS) in Aiken, SC, has been accomplished by several methods. These methods include thermal diffusion (1957--1986), fractional absorption (1964--1968), and cryogenic distillation (1967-present). Most recently, the Thermal Cycling Absorption Process (TCAP), a metal hydride based hydrogen isotope separation system, began production in the Replacement Tritium Facility (RTF) on April 9, 1994. TCAP has been in development at the Savannah River Technology Center since 1980. The production startup of this semi-continuous gas chromatographic separation process is a significant accomplishment for the Savannah River Site and was achieved after years of design, development, and testing.

  14. Startup and operation of a metal hydride based isotope separation process

    Energy Technology Data Exchange (ETDEWEB)

    Scogin, J.H.; Poore, A.S. [Westinghouse Savannah River Co., Aiken, SC (United States)

    1995-10-01

    Production scale separation of tritium from other hydrogen isotopes at the Savannah River Site (SRS) in Aiken, SC, USA, has been accomplished by several methods. These methods include thermal diffusion (1957-1986), fractional absorption (1964-1968), and cryogenic distillation (1967-present). Most recently, the Thermal Cycling Absorption Process (TCAP), a metal hydride based hydrogen isotope separation system, began production in the Replacement Tritium Facility (RTF) on April 9, 1994. TCAP has been in development at the Savannah River Technology Center since 1980. The production startup of this semi-continuous gas chromatographic separation process is a significant accomplishment for the Savannah River Site and was achieved after years of design, development, and testing. 2 refs., 4 figs.

  15. Boron Separation by the Two-step Ion-Exchange for the Isotopic Measurement of Boron

    Institute of Scientific and Technical Information of China (English)

    WANG,Qing-Zhong(王庆忠); XIAO,Ying-Kai(肖应凯); WANG,Yun-Hui(王蕴惠); ZHANG,Chong-Geng(张崇耿); WEI,Hai-Zhen(魏海珍)

    2002-01-01

    An improved procedure for extraction and purification of boron from natural samples is presented. The separation and purification of boron was carried out using a boron-specific resin, Amberlite IRA743, and a mixed ion exchange resin,Dowex 50W × 8 and Ion Exchanger Ⅱ resin. Using the mixed ion exchange resin which adsorbs all cations and anions except boron, the HCl and other cations and anions left in eluant from the Amberlite IRA 743 were removed effectively. In this case, boron loss can be avoided because the boron-bearing solution does not have to be evaporated to reach dryness to dislodge HCl. The boron recovery ranged from 97.6% to 102% in this study. The isotopic fractionation of boron can be negligible within the precision of the isotopic measurement. The results show that boron separation for the isotopic measurement by using both Amberlite IRA 743 resin and the mixed rein is more effective than that using Amberlite IRA 743 resin alone. The boron in samples of brine, seawater, rock, coral and foraminifer were separated by this procedure. Boron isotopic compositions of these samples were measured by thermal ionization mass spectrometry in this study.

  16. Automation of the isotopic separation of hydrogen through gas chromatography; Automatisation des procedes de separation isotopique des hydrogenes par chromatographie en phase gazeuse

    Energy Technology Data Exchange (ETDEWEB)

    Laquerbe, C.; Steimetz, J.; Demoment, J. [CEA Valduc, 21 - Is-sur-Tille (France); Leterq, D. [CEA Bruyeres-le-Chatel, 91 (France)

    2007-07-01

    The thermal cycling absorption process (TCAP) is a separation technique that can be considered as an evolution of the discontinuous chromatography in gaseous phase used in Cea-Dam for the isotopic separation of tritium. The shift in affinity of the palladium for the 3 hydrogen isotopes allows their separation. In the TCAP process we use the shift of the separation property in terms of operating temperatures: the ability to separate is significant at the ambient temperature while it is almost zero over 1000 C degrees. Preliminary studies have allowed the selection of palladium deposits on alumina as lining. 2 pilot installations have been designed. (A.C.)

  17. The effect of small scale variablity in isotopic composition of precipitation on hydrograph separation results

    Science.gov (United States)

    Fischer, Benjamin; van Meerveld, Ilja; Seibert, Jan

    2016-04-01

    Understanding runoff processes is important for predictions of streamflow quantity and quality. The two-component isotope hydrograph separation (IHS) method is a valuable tool to study how catchments transform rainfall into runoff. IHS allows the stormflow hydrograph to be separated into rainfall (event water) and water that was stored in the catchment before the event (pre-event water). To be able to perform an IHS, water samples of baseflow (pre-event water) and stormflow are collected at the stream outlet. Rainfall is usually collected at one location by hand as an event total or sampled sequentially during the event. It is usually assumed that the spatial variability in rainfall and the isotopic composition of rainfall are negligible for small (area of 0.15, 0.23, and 0.7 km2). The isotopic composition of rainfall and streamflow were sampled for 10 different rain events (P: 5 mm intervals, Q: 12 to 51 samples per events). This dataset was used to perform a two-component isotope hydrograph separation. The results show that for some events the spatial variability in total rainfall, mean and maximum rainfall intensity and stable isotope composition of rainfall was high. There was no relation between the stable isotope composition of rainfall and the rainfall sum, rainfall intensity or altitude. The spatial variability of the isotopic composition of rainfall was for 4 out of the 10 events as large as the temporal variability in the isotopic composition. Different rainfall weighing methods resulted in different minimum pre-event water fractions in streamflow. For small events with a small mean temporal range in stable isotope composition of rainfall, the different rainfall weighing methods had little effect on the calculated minimum pre-event water fractions. However with increasing temporal variability in stable isotope composition of rainfall, the range in the minimum pre-event water fractions increased and therefore the choice of the rainfall weighing method

  18. Ion exchange separation of chromium from natural water matrix for stable isotope mass spectrometric analysis

    Science.gov (United States)

    Ball, J.W.; Bassett, R.L.

    2000-01-01

    A method has been developed for separating the Cr dissolved in natural water from matrix elements and determination of its stable isotope ratios using solid-source thermal-ionization mass spectrometry (TIMS). The separation method takes advantage of the existence of the oxidized form of Cr as an oxyanion to separate it from interfering cations using anion-exchange chromatography, and of the reduced form of Cr as a positively charged ion to separate it from interfering anions such as sulfate. Subsequent processing of the separated sample eliminates residual organic material for application to a solid source filament. Ratios for 53Cr/52Cr for National Institute of Standards and Technology Standard Reference Material 979 can be measured using the silica gel-boric acid technique with a filament-to-filament standard deviation in the mean 53Cr/52Cr ratio for 50 replicates of 0.00005 or less. (C) 2000 Elsevier Science B.V. All rights reserved.

  19. Simultaneous assessment of cholesterol absorption and synthesis in humans using on-line gas chromatography/ combustion and gas chromatography/pyrolysis/isotope-ratio mass spectrometry.

    Science.gov (United States)

    Gremaud, G; Piguet, C; Baumgartner, M; Pouteau, E; Decarli, B; Berger, A; Fay, L B

    2001-01-01

    A number of dietary components and drugs are known to inhibit the absorption of dietary and biliary cholesterol, but at the same time can compensate by increasing cholesterol synthesis. It is, therefore, necessary to have a convenient and accurate method to assess both parameters simultaneously. Hence, we validated such a method in humans using on-line gas chromatography(GC)/combustion and GC/pyrolysis/isotope-ratio mass spectrometry (IRMS). Cholesterol absorption was measured using the ratio of [(13)C]cholesterol (injected intravenously) to [(18)O]cholesterol (administered orally). Simultaneously, cholesterol synthesis was measured using the deuterium incorporation method. Our methodology was applied to 12 mildly hypercholesterolemic men that were given a diet providing 2685 +/- 178 Kcal/day (mean +/- SD) and 255 +/- 8 mg cholesterol per day. Cholesterol fractional synthesis rates ranged from 5.0 to 10.5% pool/day and averaged 7.36% +/- 1.78% pool/day (668 +/- 133 mg/day). Cholesterol absorption ranged from 36.5-79.9% with an average value of 50.8 +/- 15.4%. These values are in agreement with already known data obtained with mildly hypercholesterolemic Caucasian males placed on a diet similar to the one used for this study. However, our combined IRMS method has the advantage over existing methods that it enables simultaneous measurement of cholesterol absorption and synthesis in humans, and is therefore an important research tool for studying the impact of dietary treatments on cholesterol parameters.

  20. Separation of polybrominated diphenyl ethers in fish for compound-specific stable carbon isotope analysis

    Energy Technology Data Exchange (ETDEWEB)

    Zeng, Yan-Hong [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Graduate University of Chinese Academy of Sciences, Beijing, 100049 (China); Luo, Xiao-Jun, E-mail: luoxiaoj@gig.ac.cn [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Chen, Hua-Shan; Wu, Jiang-Ping; Chen, She-Jun; Mai, Bi-Xian [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)

    2012-05-15

    A separation and isotopic analysis method was developed to accurately measure the stable carbon isotope ratios of polybrominated diphenyl ethers (PBDEs) with three to six substituted bromine atoms in fish samples. Sample extracts were treated with concentrated sulfuric acid to remove lipids, purified using complex silica gel column chromatography, and finally processed using alumina/silica (Al/Si) gel column chromatography. The purities of extracts were verified by gas chromatography and mass spectrometry (GC-MS) in the full-scan mode. The average recoveries of all compounds across the purification method were between 60% and 110%, with the exception of BDE-154. The stable carbon isotopic compositions of PBDEs can be measured with a standard deviation of less than 0.5 Per-Mille-Sign . No significant isotopic fraction was found during the purification of the main PBDE congeners. A significant change in the stable carbon isotope ratio of BDE-47 was observed in fish carcasses compared to the original isotopic signatures, implying that PBDE stable carbon isotopic compositions can be used to trace the biotransformation of PBDEs in biota. - Highlights: Black-Right-Pointing-Pointer A method for the purification of PBDEs for CSIA was developed. Black-Right-Pointing-Pointer The {delta}{sup 13}C of PBDE congeners can be measured with a standard deviation of less than 0.5 Per-Mille-Sign . Black-Right-Pointing-Pointer Common carp were exposed to a PBDE mixture to investigate debromination. Black-Right-Pointing-Pointer Ratios of the {delta}{sup 13}C values can be used to trace the debromination of PBDE in fish.

  1. Scalable and efficient separation of hydrogen isotopes using graphene-based electrochemical pumping

    Science.gov (United States)

    Lozada-Hidalgo, M.; Zhang, S.; Hu, S.; Esfandiar, A.; Grigorieva, I. V.; Geim, A. K.

    2017-05-01

    Thousands of tons of isotopic mixtures are processed annually for heavy-water production and tritium decontamination. The existing technologies remain extremely energy intensive and require large capital investments. New approaches are needed to reduce the industry's footprint. Recently, micrometre-size crystals of graphene are shown to act as efficient sieves for hydrogen isotopes pumped through graphene electrochemically. Here we report a fully-scalable approach, using graphene obtained by chemical vapour deposition, which allows a proton-deuteron separation factor of around 8, despite cracks and imperfections. The energy consumption is projected to be orders of magnitude smaller with respect to existing technologies. A membrane based on 30 m2 of graphene, a readily accessible amount, could provide a heavy-water output comparable to that of modern plants. Even higher efficiency is expected for tritium separation. With no fundamental obstacles for scaling up, the technology's simplicity, efficiency and green credentials call for consideration by the nuclear and related industries.

  2. On-line SPE-UHPLC method using fused core columns for extraction and separation of nine illegal dyes in chilli-containing spices.

    Science.gov (United States)

    Khalikova, Maria A; Satínský, Dalibor; Smidrkalová, Tereza; Solich, Petr

    2014-12-01

    The presented work describes the development of a simple, fast and effective on-line SPE-UHPLC-UV/vis method using fused core particle columns for extraction, separation and quantitative analysis of the nine illegal dyes, most frequently found in chilli-containing spices. The red dyes Sudan I-IV, Sudan Red 7B, Sudan Red G, Sudan Orange G, Para Red, and Methyl Red were separated and analyzed in less than 9 min without labor-consuming pretreatment procedure. The chromatographic separation was performed on Ascentis Express RP-Amide column with gradient elution using mixture of acetonitrile and water, as a mobile phase at a flow rate of 1.0 mL min(-1) and 55°C of temperature. As SPE sorbent for cleanup and pre-concentration of illegal dyes short guard fused core column Ascentis Express F5 was used. The applicability of proposed method was proven for three different chilli-containing commercial samples. Recoveries for all compounds were between 90% and 108% and relative standard deviation ranged from 1% to 4% for within- and from 2% to 6% for between-day. Limits of detection showed lower values than required by European Union regulations and were in the range of 3.3-10.3 µg L(-1) for standard solutions, 5.6-235.6 µg kg(-1) for chilli-containing spices.

  3. Combination of two different stationary phases for on-line pre-concentration and separation of basic drugs by using nano-liquid chromatography.

    Science.gov (United States)

    D'Orazio, Giovanni; Fanali, Salvatore

    2013-04-12

    Capillary columns were packed firstly with silica modified-teicoplanin (teico-CSP) particles for a short zone (1-5 cm) and then with a Cogent Bidentate C18 silica phase (25 cm). The first part of the column (inlet) was intended for focusing the sample model, consisted of selected basic compounds, while the second zone, containing RP18 particles, was used for their separation. For method optimization, some important experimental parameters were studied including the sample solvent, injected volume and teico-CSP particles length. 3 cm teico-CSP resulted to be effective for the on-line pre-concentration, before the separation, of acebutolol, alprenolol, nadolol, oxprenolol and terbutaline with limit of detection at levels of few ng/mL. The comparison of the data obtained in absence of the chiral stationary phase revealed that the use of this chiral short sector into the capillary allowed the increase of the sensitivity of 5-12 times. Injection of larger sample volumes were easily done using higher length of the teico-CSP into the capillary, however the use of 5 cm length was not appropriate because caused the partial chiral separation of some studied compounds.

  4. Determination of 2-propanol in surface cleaning solutions used for copper continuous casting process by flow injection-spectrophotometric detection with on-line column separation.

    Science.gov (United States)

    Hayashibe, Yutaka; Tokuda, Masahiro; Takeya, Minoru

    2003-09-01

    A flow-injection system has been developed for the determination of 2-propanol in the surface cleaning solutions used in the copper continuous cast rod making system. Adsorption chromatography in nitric acid medium was used for the on-line separation of oily substances in the sample solution. Cerium(IV) diammonium nitrate was utilized as the chromogenic reagent for the spectrophotometric detection of 2-propanol. The system permits a throughput of one sample per hour for the oily sample, and of 12 samples per hour for the none-oily sample. The reproducibility has been proven to be satisfactory with a relative standard deviation of less than 6.0% (2.2%(V/V) 2-propanol level, n = 23). The detection limit is 0.01% (V/V).

  5. Analysis and optimization of gas-centrifugal separation of uranium isotopes by neural networks

    Directory of Open Access Journals (Sweden)

    Migliavacca S.C.P.

    2002-01-01

    Full Text Available Neural networks are an attractive alternative for modeling complex problems with too many difficulties to be solved by a phenomenological model. A feed-forward neural network was used to model a gas-centrifugal separation of uranium isotopes. The prediction showed good agreement with the experimental data. An optimization study was carried out. The optimal operational condition was tested by a new experiment and a difference of less than 1% was found.

  6. Aspects regarding at 13C isotope separation column control using Petri nets system

    Science.gov (United States)

    Boca, M. L.; Ciortea, M. E.

    2015-11-01

    This paper is intended to show that Petri nets can be also applicable in the chemical industry. It used linear programming, modeling underlying Petri nets, especially discrete event systems for isotopic separation, the purpose of considering and control events in real-time through graphical representations. In this paper it is simulate the control of 13C Isotope Separation column using Petri nets. The major problem with 13C comes from the difficulty of obtaining it and raising its natural fraction. Carbon isotopes can be obtained using many methods, one of them being the cryogenic distillation of carbon monoxide. Some few aspects regarding operating conditions and the construction of such cryogenic plants are known today, and even less information are available as far as the separation process modeling and control are concerned. In fact, the efficient control of the carbon monoxide distillation process represents a necessity for large-scale 13C production. Referring to a classic distillation process, some models for carbon isotope separation have been proposed, some based on mass, component and energy balance equations, some on the nonlinear wave theory or the Cohen equations. For modeling the system it was used Petri nets because in this case it is deal with discrete event systems. In use of the non-timed and with auxiliary times Petri model, the transport stream was divided into sections and these sections will be analyzed successively. Because of the complexity of the system and the large amount of calculations required it was not possible to analyze the system as a unitary whole. A first attempt to model the system as a unitary whole led to the blocking of the model during simulation, because of the large processing times.

  7. The use of a polymer inclusion membrane in flow injection analysis for the on-line separation and determination of zinc.

    Science.gov (United States)

    Zhang, Lujia L; Cattrall, Robert W; Kolev, Spas D

    2011-06-15

    This paper reports the first use of a polymer inclusion membrane (PIM) for on-line separation in flow injection analysis (FIA) involving simultaneous extraction and back-extraction. The FIA system containing the PIM separation module was used for the determination of Zn(II) in aqueous samples in the presence of Mg(II), Ca(II), Cd(II), Co(II), Ni(II), Cu(II), and Fe(III). The Fe(III) and Cu(II) interferences were eliminated by off-line precipitation with phosphate and on-line complexation with chloride, respectively. The concentration of Zn(II) was determined spectrophotometrically using 4-(2-pyridylazo) resorcinol (PAR). The optimal composition of the PIM consisted of 40% (m/m) di(2-ethlyhexyl) phosphoric acid (D2EHPA) as carrier, 10% (m/m) dioctyl phthalate (DOP) as plasticizer and 50% (m/m) poly(vinyl chloride) (PVC) as the base polymer. The optimized FIA system was characterized by a linear calibration curve in the range from 1.0 to 30.0 mg L(-1) Zn(II), a detection limit of 0.05 mg L(-1) and a relative standard deviation of 3.4% with a sampling rate of 4h(-1). Reproducible results were obtained for 20 replicate injections over a 5h period which demonstrated a good membrane stability. The FIA system was applied to the determination of Zn(II) in pharmaceuticals and samples from the galvanizing industry and very good agreement with atomic absorption spectrometry was obtained.

  8. Gas chromatographic separation for the H and C stable isotope ratio determination of coal compounds

    Energy Technology Data Exchange (ETDEWEB)

    Antenucci, D.; Jacquemin, C. [Institut Scientifique de Service Public, Liege (Belgium); Bouquegneau, J.M.; Brasseur, A.; Dauby, P.; Pirard, J.P. [Universite de Liege (Belgium); Letolle, R. [Universite Pierre et Marie Curie, Paris (France)

    1997-06-01

    A new, completely automated gas chromatography technique has been developed to separate the different gaseous compounds produced during underground coal gasification for their {sup 13}C/{sup 12}C and D/H isotope ratio measurements. The technique was designed for separation and collection of H{sub 2}, CO, CO{sub 2}, H{sub 2}O, H{sub 2}S, CH{sub 4}, and heavier hydrocarbons. These gaseous compounds are perfectly separated by the gas-phase chromatograph and quantitatively sent to seven combustion and collection lines. H{sub 2}, CO, CH{sub 4}, and heavier hydrocarbons are quantitatively oxidized to CO{sub 2} and/or H{sub 2}O. The isotopic analyses are performed by the sealed-tube method. The zinc method is used for reduction of both water and H{sub 2}S to hydrogen for D/H analysis. Including all preparation steps, the reproducibility of isotope abundance values, for a quantity higher than or equal to 0.1 mL of individual components in a mixture (5 mL of gases being initially injected in the gas chromatograph), is {+-}0.1 per mil for {delta}{sup 13}C{sub PDB} and {+-}6 per mil for {delta}D{sub SMOW}. 20 refs., 3 figs., 4 tabs.

  9. Development of an analytical method for the determination of the misuse in sports of boldenone through the analysis of urine by on-line coupling liquid chromatography-gas chromatography-combustion-isotope ratio mass spectrometry.

    Science.gov (United States)

    Toledano, R M; Díaz-Plaza, E M; Cortes, J M; Aragón, A; Vázquez, A M; Villén, J; Muñoz-Guerra, J

    2014-11-28

    Boldenone (Bo), androsta-1,4-dien-17β-ol-3-one, is an anabolic androgenic steroid not clinically approved for human application. Despite this, many cases are reported every year of athletes testing positive for Bo or its main metabolite 5β-androst-1-en-17β-ol-3-one (BoM). Recently the capability of different human intestinal bacteria to produce enzymes able to modify endogenous steroids in Bo has been demonstrated. When a urinary concentration of Bo and/or BoM between 5 and 30 ng/mL is measured a complementary analysis by gas chromatography combustion isotope ratio mass spectrometry (GC-C-IRMS) must be carried out to discriminate the endogenous or exogenous origin. In the present work, a novel analytical method that couples LC-GC by means of the TOTAD interface with C-IRMS is described. The method is based on a first RPLC separation of unacetyled steroids, followed by acetylation and automated on-line LC-GC-C-IRMS, which includes a second RPLC clean-up of acetyl Bo and BoM, isolation of the two fractions in a fraction collector and their consecutive analysis by GC-C-IRMS. The method has been applied to the analysis of urine samples fortified at 5 and 10 ng/mL, where it has shown a good performance.

  10. Separation and quantification of {sup 238}U, {sup 232}Th and rare earths in monazite samples by ion chromatography coupled with on-line flow scintillation detector

    Energy Technology Data Exchange (ETDEWEB)

    Borai, E.H.; Mady, A.S

    2002-10-01

    An alternative procedure has been described for efficient separation and quantitative determination of uranium (U), thorium (Th) and rare earth elements (REEs) in monazite mineral by high performance ion chromatographic system (IC). Different variables affecting the distribution coefficient, the retention and hence separation efficiency such as eluent flow rate and concentrations of HCl and ammonium sulfate (NH{sub 4}){sub 2}SO{sub 4} containing the mobile phase were studied. The developed separation protocol of U, Th and REEs was optimized using an Ion Pac CS5 separation column followed by post-column derivatization reaction with Arsenaso III and UV-VIS spectrophotometeric detection. Comparative evaluation of U, Th and REEs concentration in monazite mineral was demonstrated using two different on-line detection modes including flow through cell scintillation detector (FSD) and UV-VIS spectrophotometer. Response of the FSD was found to be linear over the full range of activities investigated (4-100 Bq). The lower limits of detection (LLD) for the investigated radionuclides were 3.0{+-}0.1 Bq for {sup 238}U and 6.0{+-}0.1 Bq for {sup 232}Th. The detection of {sup 238}U and {sup 232}Th by FSD shows good agreement with the corresponding determination by UV-VIS spectrophotometer. The content of ThO{sub 2} and U{sub 3}O{sub 8} in monazite sample were found to be 4.7{+-}0.1% and 0.42{+-}0.04% using UV-VIS detector and 4.3{+-}0.1% and 0.45{+-}0.1% using FSD, respectively.

  11. Development of the helium-jet fed on-line mass separator RAMA and its application to studies of T/sub z/ = -2 nuclei

    Energy Technology Data Exchange (ETDEWEB)

    Moltz, D.M.

    1979-10-01

    The study of nuclei far from beta stability is hampered greatly when the nuclide of interest decays in a manner identical to that of a nuclide produced in greater yield in the same bombardment. One solution to this problem is through the use of an on-line mass separator. Development of the Berkelely helium-jet fed on-line mass separator RAMA is discussed as applied to studies of the A = 4n, T/sub z/ = -2 nuclides. RAMA (Recoil Atom Mass Analyzer) has typical efficiencies of 0.1% for approx. 75 elements with melting points less than or equal to 2000/sup 0/C. This efficiency permits decay studies to be readily performed on nuclei with production cross sections greater than or equal to 500 ..mu..b for ..gamma..-ray spectroscopy and greater than or equal to 1 ..mu..b for discrete energy charged particle spectroscopy. The mass range on the normalized RAMA focal plane is +- 10%. The quoted efficiency is for a mass resolution of M/..delta..M approx. 300. RAMA has been used to observe two members of the A = 4n, T/sub z/ = -2 series of beta-delayed proton emitters, /sup 20/Mg and /sup 24/Si. Observation of beta-delayed protons from a mass-separated sample of /sup 20/Mg(t/sub 1/2/ approx. 95 ms) establishes the mass-excess of the lowest T = 2 (0/sup +/) state in /sup 20/Na (13.42 +- .05 MeV), thereby completing the mass twenty isospin quintet. A similar measurement of the decay of /sup 24/Si (t/sub 1/2/ approx. 100 ms) establishes the mass-excess of the lowest T = 2 (0/sup +/) state in /sup 24/Al (5.903 +- 0.009 MeV). The mass 24 isospin quintet is incomplete because the mass of /sup 24/Si remains unknown. In both cases, excellent agreement is obtained using only the quadratic form of the isobaric multiplet mass equation (IMME). 79 references.

  12. Separation Of Uranium And Plutonium Isotopes For Measurement By Multi Collector Inductively Coupled Plasma Mass Spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Martinelli, R E; Hamilton, T F; Williams, R W; Kehl, S R

    2009-03-29

    Uranium (U) and plutonium (Pu) isotopes in coral soils, contaminated by nuclear weapons testing in the northern Marshall Islands, were isolated by ion-exchange chromatography and analyzed by mass spectrometry. The soil samples were spiked with {sup 233}U and {sup 242}Pu tracers, dissolved in minerals acids, and U and Pu isotopes isolated and purified on commercially available ion-exchange columns. The ion-exchange technique employed a TEVA{reg_sign} column coupled to a UTEVA{reg_sign} column. U and Pu isotope fractions were then further isolated using separate elution schemes, and the purified fractions containing U and Pu isotopes analyzed sequentially using multi-collector inductively coupled plasma mass spectrometer (MCICP-MS). High precision measurements of {sup 234}U/{sup 235}U, {sup 238}U/{sup 235}U, {sup 236}U/{sup 235}U, and {sup 240}Pu/{sup 239}Pu in soil samples were attained using the described methodology and instrumentation, and provide a basis for conducting more detailed assessments of the behavior and transfer of uranium and plutonium in the environment.

  13. Isotope separation method for preparing novel semiconductors, and semiconductor junctions containing the novel semiconductor

    Energy Technology Data Exchange (ETDEWEB)

    Fanica, M.M.; Ivascu, M.; Ilas, G.; Dumitru, I.

    1997-02-20

    An isotope separation method for use in the field of semiconductors is provided. The method is an improvement to the invention disclosed in OSIM patent application no. 95-01302 of 13.07.1995. Specifically, a method is provided for processing a semiconductor element having a cubic, rhombic or hexagonal crystalline structure and containing at least two stable isotopes, to enable the concentration of the various isotopes to be altered. The method comprises exposing the element to a temperature adjacent to its diffusion temperature, simultaneously applying to the element a 1 Amp., 4-30 KV electric current proportional to the ionisation energy expressed in Kcal/g mol, arranging the element being processed in a gaseous medium containing at least one inert gas to prevent oxidation of the element, and continuing the process for around 2 hours. An antimony (Sb) element with an isotope ratio of Sb 121 (P1,P2):Sb 123 (P3) = 1.70 is also provided. (author) figs.

  14. Mode-Locked CO Laser for Isotope Separation of Uranium Employing Condensation Repression

    Directory of Open Access Journals (Sweden)

    Igor Y. Baranov

    2010-01-01

    Full Text Available In the present work, we have suggested a technical solution of a CO laser facility for industrial separation of uranium used in the production of fuel for nuclear power plants. There has been used a method of laser isotope separation of uranium, employing condensation repression in a free jet. The laser operation with nanosecond pulse irradiation can provide acceptable efficiency in the separating unit and the high effective coefficient of the laser with the wavelength of 5.3 μm. Receiving a uniform RF discharge under medium pressure and high Mach numbers in the gas stream solves the problem of an electron beam and cryogenic cooler of CO lasers. The laser active medium is being cooled while it is expanding in the nozzle; a low-current RF discharge is similar to a non-self-sustained discharge. In the present work, we have developed a calculation model of optimization and have defined the parameters of a mode-locked CO laser with an RF discharge in the supersonic stream. The CO laser average power of 3 kW is sufficient for efficient industrial isotope separation of uranium at one facility.

  15. Modelling aspects regarding the control in 13C isotope separation column

    Science.gov (United States)

    Boca, M. L.

    2016-08-01

    Carbon represents the fourth most abundant chemical element in the world, having two stable and one radioactive isotope. The 13Carbon isotopes, with a natural abundance of 1.1%, plays an important role in numerous applications, such as the study of human metabolism changes, molecular structure studies, non-invasive respiratory tests, Alzheimer tests, air pollution and global warming effects on plants [9] A manufacturing control system manages the internal logistics in a production system and determines the routings of product instances, the assignment of workers and components, the starting of the processes on not-yet-finished product instances. Manufacturing control does not control the manufacturing processes themselves, but has to cope with the consequences of the processing results (e.g. the routing of products to a repair station). In this research it was fulfilled some UML (Unified Modelling Language) diagrams for modelling the C13 Isotope Separation column, implement in STARUML program. Being a critical process and needing a good control and supervising, the critical parameters in the column, temperature and pressure was control using some PLC (Programmable logic controller) and it was made some graphic analyze for this to observe some critical situation than can affect the separation process. The main parameters that need to be control are: -The liquid nitrogen (N2) level in the condenser. -The electrical power supplied to the boiler. -The vacuum pressure.

  16. Continuous-flow separation and pre-concentration coupled on-line to solid-surface fluorescence spectroscopy for the simultaneous determination of o-phenylphenol and thiabendazole.

    Science.gov (United States)

    García Reyes, J F; Llorent Martínez, E J; Ortega Barrales, P; Molina Díaz, A

    2004-01-01

    A novel and single flow-injection system combined with solid-surface fluorescence detection is proposed in this work for the resolution of a mixture of two widely used pesticides (o-phenylphenol and thiabendazole). The continuous-flow methodology is based on the implementation of on-line pre-concentration and separation of both analytes on the surface of C18 silica gel beads placed just inside the flow cell, implemented with gel-phase fluorimetric multi-wavelength detection (using 305/358 and 250/345 nm as excitation/emission wavelengths for thiabendazole and o-phenylphenol, respectively). The separation of the pesticides was possible owing to the different retention/desorption kinetics of their interactions with the solid support in the zone where the stream impinges on the solid material. No previous separation of the analytes before they reach the flow cell is needed thereby simplifying substantially both the procedure and the manifold. By using a sample volume of 2,600 microL, the system was calibrated in the range 0.5-16 and 5-120 ng mL(-1) with detection limits of 0.09 and 0.60 ng mL(-1) for thiabendazole and o-phenylphenol, respectively. The RSD values (n=10) were about 1% for both analytes. The proposed methodology was applied to environmental water samples and also to various commercial pesticide formulations containing both analytes. Recovery percentages were 97-103% and 98-102% for thiabendazole and o-phenylphenol, respectively.

  17. Photon Scattering from the Stable Even-Mass Mo Isotopes Below the Neutron-Separation Energy

    Science.gov (United States)

    Rusev, G.; Hutcheson, A.; Kwan, E.; Tonchev, A. P.; Tornow, W.; Angell, C.; Hammond, S.; Karwowski, H. J.; Kelley, J. H.; Schwengner, R.; Dönau, F.; Wagner, A.

    2008-10-01

    We present results from photon-scattering experiments on the stable even-mass molybdenum isotopes below the neutron-separation energy carried out with bremsstrahlung at the superconducting electron accelerator ELBE at the Research Center Dresden-Rossendorf in Germany, and with monoenergetic photon beams at the HIγS facility at TUNL. We applied statistical methods in order to correct for the branching and cascade transitions and to determine the photoabsorption cross section. The obtained results allowed us to extend the tail of the Giant Dipole Resonance below the (,) threshold down to 4 MeV. The photoabsorption cross sections deduced from the present experiments show that the dipole strength increases with the neutron number of the Mo isotopes. The experimental results are discussed in the frame of Quasiparticle-Random-Phase-Approximation in a deformed basis which describe the increasing strength as a result of the deformation.

  18. Extraction, separation, and intramolecular carbon isotope characterization of athabasca oil sands acids in environmental samples.

    Science.gov (United States)

    Ahad, Jason M E; Pakdel, Hooshang; Savard, Martine M; Simard, Marie-Christine; Smirnoff, Anna

    2012-12-04

    Here we report a novel approach to extract, isolate, and characterize high molecular weight organic acids found in the Athabasca oil sands region using preparative capillary gas chromatography (PCGC) followed by thermal conversion/elemental analysis-isotope ratio mass spectrometry (TC/EA-IRMS). A number of different "naphthenic acids" surrogate standards were analyzed as were samples from the bitumen-rich unprocessed McMurray Formation, oil sands process water, groundwater from monitoring wells, and surface water from the Athabasca River. The intramolecular carbon isotope signature generated by online pyrolysis (δ(13)C(pyr)) showed little variation (±0.6‰) within any given sample across a large range of mass fractions separated by PCGC. Oil sand, tailings ponds, and deep McMurray Formation groundwater were significantly heavier (up to ∼9‰) compared to surface water and shallow groundwater samples, demonstrating the potential use of this technique in source apportionment studies.

  19. Production of intense metallic ion beams in order of isotopic separations; Production de faisceaux intenses d'ions metalliques en vue de la separation des isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Sarrouy, J.L. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    We describe an isotope separator with magnetic sector of 60 deg that permits, with a process of neutralization of the space charge, to use efficiently intense ion beams. The sources of realized ions provide ionic debits of 10 mA. This present work deals who to obtain intense ion beams (10 to 15 mA), different processes of ion currents measurement, as well as the study of the phenomenon of space charge neutralization. The second part of this memory will be on the survey and the adaptation on the source of various type of oven permitting to spray and to ionize metals directly. By order of increasing difficulty of vaporization, we reached the chromium. (M.B.) [French] 0n decrit un separateur d'isotope a secteur magnetique de 60 deg qui permet, grace a un procede de neutralisation de la charge d'espace, d'utiliser efficacement des faisceaux d'ions intenses. Les sources d'ions realisees fournissent des debits ioniques de 10 mA. Ce present travail porte sur l'obtention de faisceaux d'ions faisceaux d'ions intenses (10 a 15 mA), des differents procedes de mesures des courants d'ions, ainsi que l'etude du phenomene de neutralisation de charge d'espace. La deuxieme partie de ce memoire portera sur l'etude et l'adaptation sur la source de divers type de four permettant de vaporiser et d'ioniser directement les metaux. Par ordre de difficulte croissantes de vaporisations, nous avons atteint le chrome. (M.B.)

  20. Production of intense metallic ion beams in order of isotopic separations; Production de faisceaux intenses d'ions metalliques en vue de la separation des isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Sarrouy, J.L. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    We describe an isotope separator with magnetic sector of 60 deg that permits, with a process of neutralization of the space charge, to use efficiently intense ion beams. The sources of realized ions provide ionic debits of 10 mA. This present work deals who to obtain intense ion beams (10 to 15 mA), different processes of ion currents measurement, as well as the study of the phenomenon of space charge neutralization. The second part of this memory will be on the survey and the adaptation on the source of various type of oven permitting to spray and to ionize metals directly. By order of increasing difficulty of vaporization, we reached the chromium. (M.B.) [French] 0n decrit un separateur d'isotope a secteur magnetique de 60 deg qui permet, grace a un procede de neutralisation de la charge d'espace, d'utiliser efficacement des faisceaux d'ions intenses. Les sources d'ions realisees fournissent des debits ioniques de 10 mA. Ce present travail porte sur l'obtention de faisceaux d'ions faisceaux d'ions intenses (10 a 15 mA), des differents procedes de mesures des courants d'ions, ainsi que l'etude du phenomene de neutralisation de charge d'espace. La deuxieme partie de ce memoire portera sur l'etude et l'adaptation sur la source de divers type de four permettant de vaporiser et d'ioniser directement les metaux. Par ordre de difficulte croissantes de vaporisations, nous avons atteint le chrome. (M.B.)

  1. Nanoporous materials for hydrogen storage and H{sub 2}/D{sub 2} isotope separation

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Hyunchul

    2014-05-05

    This thesis presents a study of hydrogen adsorption properties at RT with noble metal doped porous materials and an efficient separation of hydrogen isotopes with nanoporous materials. Most analysis is performed via thermal desorption spectra (TDS) and Sieverts-type apparatus. The result and discussion is presented in two parts; Chapter 4 focuses on metal doped nanoporous materials for hydrogen storage. Cryogenic hydrogen storage by physisorption on porous materials has the advantage of high reversibility and fast refuelling times with low heat evolution at modest pressures. At room temperature, however, the physisorption mechanism is not abEle to achieve enough capacity for practical application due to the weak van der Waals interaction, i.e., low isosteric heats for hydrogen sorption. Recently, the ''spillover'' effect has been proposed by R. Yang et al. to enhance the room temperature hydrogen storage capacity. However, the mechanism of this storage enhancement by decoration of noble metal particles inside high surface area supports is not yet fully understood and still under debate. In this chapter, noble metal (Pt / Pd) doped nanoporous materials (i.e. porous carbon, COFs) have been investigated for room temperature hydrogen storage. Their textural properties and hydrogen storage capacity are characterized by various analytic techniques (e.g. SEM, HRTEM, XRD, BET, ICP-OES, Thermal desorption spectra, Sievert's apparatus and Raman spectroscopy). Firstly, Pt-doped and un-doped templated carbons possessing almost identical textural properties were successfully synthesized via a single step wet impregnation method. This enables the study of Pt catalytic activities and hydrogen adsorption kinetics on porous carbons at ambient temperature by TDS after H{sub 2}/D{sub 2} gas exposure and PCT measurement, respectively. While the H{sub 2} adsorption kinetics in the microporous structure is enhanced by Pt catalytic activities (spillover), only a

  2. On-line laser spectroscopy with thermal atomic beams

    CERN Document Server

    Thibault, C; De Saint-Simon, M; Duong, H T; Guimbal, P; Huber, G; Jacquinot, P; Juncar, P; Klapisch, Robert; Liberman, S; Pesnelle, A; Pillet, P; Pinard, J; Serre, J M; Touchard, F; Vialle, J L

    1981-01-01

    On-line high resolution laser spectroscopy experiments have been performed in which the light from a CW tunable dye laser interacts at right angles with a thermal atomic beam. /sup 76-98/Rb, /sup 118-145 /Cs and /sup 208-213/Fr have been studied using the ionic beam delivered by the ISOLDE on-line mass separator at CERN while /sup 30-31/Na and /sup 38-47/K have been studied by setting the apparatus directly on-line with the PS 20 GeV proton beam. The principle of the method is briefly explained and some results concerning nuclear structure are given. The hyperfine structure, spins and isotope shifts of the alkali isotopes and isomers are measured. (8 refs).

  3. RAPID SEPARATION METHOD FOR 237NP AND PU ISOTOPES IN LARGE SOIL SAMPLES

    Energy Technology Data Exchange (ETDEWEB)

    Maxwell, S.; Culligan, B.; Noyes, G.

    2010-07-26

    A new rapid method for the determination of {sup 237}Np and Pu isotopes in soil and sediment samples has been developed at the Savannah River Site Environmental Lab (Aiken, SC, USA) that can be used for large soil samples. The new soil method utilizes an acid leaching method, iron/titanium hydroxide precipitation, a lanthanum fluoride soil matrix removal step, and a rapid column separation process with TEVA Resin. The large soil matrix is removed easily and rapidly using this two simple precipitations with high chemical recoveries and effective removal of interferences. Vacuum box technology and rapid flow rates are used to reduce analytical time.

  4. First on-line applications of multi-reflection time-of-flight mass separator at ISOLTRAP and the mass measurement of $^{82}$Zn

    CERN Document Server

    Wolf, Robert

    This thesis describes the implementation and first on-line application of a multi-reflection time-of-flight (MR-ToF) mass analyzer for high-resolution mass separation at the ISOLTRAP mass spectrometer at ISOLDE/CERN. On the one hand, the major objective was to improve ISOLTRAPs mass-measurement capabilities with respect to the ratio of delivered contaminating ions to ions of interest. On the other hand, the time necessary to purify wanted from unwanted species should be reduced as much as possible to enable access to even more exotic nuclei. The device has been set up, optimized and tested at the University of Greifswald before its move to ISOLTRAP. The achieved performance comprises mass resolving powers of up to 200000 reached at observation times of 30ms and a contamination suppression of about four orders of magnitude by use of a Bradbury-Nielsen gate. With the characteristics, it outperforms clearly the so far state-of-the-art purification method of a gas-filled Penning trap. To improve the utilization o...

  5. An efficient VLSI implementation of on-line recursive ICA processor for real-time multi-channel EEG signal separation.

    Science.gov (United States)

    Shih, Wei-Yeh; Liao, Jui-Chieh; Huang, Kuan-Ju; Fang, Wai-Chi; Cauwenberghs, Gert; Jung, Tzyy-Ping

    2013-01-01

    This paper presents an efficient VLSI implementation of on-line recursive ICA (ORICA) processor for real-time multi-channel EEG signal separation. The proposed design contains a system control unit, a whitening unit, a singular value decomposition unit, a floating matrix multiply unit and, and an ORICA weight training unit. Because the input sample rate of the ORICA processor is 128 Hz, the ORICA processor should produce independent components before the next sample is input in 1/128 s. Under the timing constraints of commutating multi-channel ORICA in real time, the design of the ORICA processor is a mixed architecture, which is designed as different hardware parallelism according to the complexity of processing units. The shared arithmetic processing unit and shared register can reduce hardware complexity and power consumption. The proposed design is implemented used TSMC 90 nm CMOS technology with 8-channel EEG processing in 128 Hz sample rate of raw data and consumes 2.827 mW at 50 MHz clock rate. The performance of the proposed design is also shown to reach 0.0078125 s latency after each EEG sample time, and the average correlation coefficient between the original source signals and extracted ORICA signals for each 1 s frame is 0.9763.

  6. LACAN Code for global simulation of SILVA laser isotope separation process; L.A.C.A.N.: Code de simulation globale du procede de separation isotopique par laser Silva

    Energy Technology Data Exchange (ETDEWEB)

    Quaegebeur, J.P.; Goldstein, S.

    1991-12-31

    Functions used for the definition of a SILVA separator require quite a lot of dimensional and operating parameters. Sizing a laser isotope separation plant needs the determination of these parameters for optimization. In the LACAN simulation code, each elementary physical process is described by simplified models. An example is given for a uranium isotope separation plant whose separation power is optimized with 6 parameters.

  7. Laser enhanced microwave plasma isotope separation. Final report, September 30, 1992--September 29, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Brake, M.L.; Gilgenbach, R.M.

    1996-06-01

    The experimental research was to focus on laser excitation of a low abundance isotope and then ionize and separate the isotope of low abundance using a microwave/ECR discharge at 2.45 GHz. A small compact electron cyclotron resonance ion source, which uses permanent magnets, was constructed during this project. The dye laser was purchased and later an excimer laser had to also be purchased because it turned out that the dye laser could not be pumped by our copper laser. It was intended that the dye laser be tuned to a wavelength of 670.8 nm, which would excite {sup 6}Li which would then be preferentially ionized by the ECR source and collected with a charged grid. The degree of enrichment was to be determined using thermal ionization mass spectrometry. The final objective of this project was to assess the feasibility of this system to large-scale production of stable isotopes. However the funding of this project was interrupted and we were not able to achieve all of our goals.

  8. Production and separation of neutron-rich rare isotopes around and below the Fermi energy

    CERN Document Server

    Souliotis, G A; Chubarian, G; Yennello, S J

    2003-01-01

    The production of n-rich rare isotopes around and below the Fermi energy is investigated using beams from the K500 Superconducting Cyclotron and the MARS recoil separator at the Cyclotron Institute of Texas A and M University. The experimental results from the reactions of 25 MeV/nucleon sup 8 sup 6 Kr + sup 6 sup 4 Ni and 21 MeV/nucleon sup 1 sup 2 sup 4 Sn + sup 1 sup 2 sup 4 Sn are presented and compared with simulations. The calculations involve a deep inelastic transfer (DIT) code for the primary interaction stage followed by the code GEMINI for the de-excitation stage. The results are also compared with the EPAX parametrization. The data on the 25 MeV/nucleon sup 8 sup 6 Kr + sup 6 sup 4 Ni reaction show that both proton-removal and several-neutron pick-up isotopes are produced. An enhancement is observed in the production of n-rich isotopes close to the projectile relative to the predictions of DIT/GEMINI and the expectations of EPAX. The data of 21 MeV/nucleon sup 1 sup 2 sup 4 Sn + sup 1 sup 2 sup 4 ...

  9. Hydrograph Separation in the Headwaters of the Shule River Basin: Combining Water Chemistry and Stable Isotopes

    Directory of Open Access Journals (Sweden)

    Jiaxin Zhou

    2015-01-01

    Full Text Available The runoff components were identified in the headwater area of Shule River Basin, using isotopic and chemical tracing with particular focus on the temporal variations of catchment sources. A total of 95 samples, including precipitation, groundwater, and glacial meltwater, were collected and analyzed for stable water isotopes (18O and 2H and major chemical ion parameters (potassium, sodium, calcium, magnesium, sulfate, chloride, and bicarbonate. Based on the isotope and water chemistry data, we applied end member mixing analysis (EMMA to identify and quantify the major runoff generating sources and their contributions. The contributions of groundwater, precipitation, and glacial meltwater were 66.7%, 19.9%, and 13.4%, respectively. The study indicated that groundwater dominated runoff in the headwater area of Shule River Basin. The roles of glacier meltwater should be remarkable in water resource management in this basin. The uncertainties of the EMMA method were summarized and estimated via a classical Gaussian error propagation technique. Analyses suggested that the uncertainty in the measurement method was less important than that in the temporal and spatial variations of tracer concentrations. The uncertainty was sensitive when the difference between mixing components was small. Therefore, the variation of tracers and the difference of mixing components should be considered when hydrograph separation was applied in the basin.

  10. Theoretical and experimental comparison of one dimensional versus on-line comprehensive two dimensional liquid chromatography for optimized sub-hour separations of complex peptide samples.

    Science.gov (United States)

    Sarrut, Morgan; Rouvière, Florent; Heinisch, Sabine

    2017-05-19

    This study was devoted to the search for conditions leading to highly efficient sub-hour separations of complex peptide samples with the objective of coupling to mass spectrometry. In this context, conditions for one dimensional reversed phase liquid chromatography (1D-RPLC) were optimized on the basis of a kinetic approach while conditions for on-line comprehensive two-dimensional liquid chromatography using reversed phase in both dimensions (on-line RPLCxRPLC) were optimized on the basis of a Pareto-optimal approach. Maximizing the peak capacity while minimizing the dilution factor for different analysis times (down to 5min) were the two objectives under consideration. For gradient times between 5 and 60min, 15cm was found to be the best column length in RPLC with sub-2μm particles under 800bar as system pressure. In RPLCxRPLC, for less than one hour as first dimension gradient time, the sampling rate was found to be a key parameter in addition to conventional parameters including column dimension, particle size, flow-rate and gradient conditions in both dimensions. It was shown that the optimum sampling rate was as low as one fraction per peak for very short gradient times (i.e. below 10min). The quality descriptors obtained under optimized RPLCxRPLC conditions were compared to those obtained under optimized RPLC conditions. Our experimental results for peptides, obtained with state of the art instrumentation, showed that RPLCxRPLC could outperform 1D-RPLC for gradient times longer than 5min. In 60min, the same peak intensity (same dilution) was observed with both techniques but with a 3-fold lower injected amount in RPLCxRPLC. A significant increase of the signal-to-noise ratio mainly due to a strong noise reduction was observed in RPLCxRPLC-MS compared to the one in 1D-RPLC-MS making RPLCxRPLC-MS a promising technique for peptide identification in complex matrices. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Fast isotopic separation of (10) B and (11) B boric acid by capillary zone electrophoresis.

    Science.gov (United States)

    Kamencev, Mikhail; Yakimova, Nina; Moskvin, Leonid; Kuchumova, Irina; Tkach, Kirill; Malinina, Yulia

    2016-11-01

    Fast isotopic separation of (10) B and (11) B boric acid by CZE was demonstrated. The BGE contained 25 mM phenylalanine and 5 mM putrescine (рН 8.95). The running conditions were +25 kV at 20°C with indirect photometric detection at 210 nm. Baseline separation was achieved in less than 9 min. RSD of migration times and corrected peak areas were less than 0.5 and 3%, respectively (n = 5). Linearity was demonstrated in the range 0.2-2 mM for (11) B and 0.2-0.5 mM for (10) B. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. On-Line Hydrogen-Isotope Measurements of Organic Samples Using Elemental Chromium : An Extension for High Temperature Elemental-Analyzer Techniques

    NARCIS (Netherlands)

    Gehre, Matthias; Renpenning, Julian; Gilevska, Tetyana; Qi, Haiping; Coplen, Tyler B.; Meijer, Harro A. J.; Brand, Willi A.; Schimmelmann, Arndt

    2015-01-01

    The high temperature conversion (HTC) technique using an elemental analyzer with a glassy carbon tube and filling (temperature conversion/elemental analysis, TC/EA) is a widely used method for hydrogen isotopic analysis of water and many solid and liquid organic samples with analysis by isotope-rati

  13. Stability of arsenic peptides in plant extracts: off-line versus on-line parallel elemental and molecular mass spectrometric detection for liquid chromatographic separation.

    Science.gov (United States)

    Bluemlein, Katharina; Raab, Andrea; Feldmann, Jörg

    2009-01-01

    The instability of metal and metalloid complexes during analytical processes has always been an issue of an uncertainty regarding their speciation in plant extracts. Two different speciation protocols were compared regarding the analysis of arsenic phytochelatin (As(III)PC) complexes in fresh plant material. As the final step for separation/detection both methods used RP-HPLC simultaneously coupled to ICP-MS and ES-MS. However, one method was the often used off-line approach using two-dimensional separation, i.e. a pre-cleaning step using size-exclusion chromatography with subsequent fraction collection and freeze-drying prior to the analysis using RP-HPLC-ICP-MS and/or ES-MS. This approach revealed that less than 2% of the total arsenic was bound to peptides such as phytochelatins in the root extract of an arsenate exposed Thunbergia alata, whereas the direct on-line method showed that 83% of arsenic was bound to peptides, mainly as As(III)PC(3) and (GS)As(III)PC(2). Key analytical factors were identified which destabilise the As(III)PCs. The low pH of the mobile phase (0.1% formic acid) using RP-HPLC-ICP-MS/ES-MS stabilises the arsenic peptide complexes in the plant extract as well as the free peptide concentration, as shown by the kinetic disintegration study of the model compound As(III)(GS)(3) at pH 2.2 and 3.8. But only short half-lives of only a few hours were determined for the arsenic glutathione complex. Although As(III)PC(3) showed a ten times higher half-life (23 h) in a plant extract, the pre-cleaning step with subsequent fractionation in a mobile phase of pH 5.6 contributes to the destabilisation of the arsenic peptides in the off-line method. Furthermore, it was found that during a freeze-drying process more than 90% of an As(III)PC(3) complex and smaller free peptides such as PC(2) and PC(3) can be lost. Although the two-dimensional off-line method has been used successfully for other metal complexes, it is concluded here that the fractionation and

  14. Improvements to the on-line mass separator, RAMA, and the beta-delayed charged-particle emission of proton-rich sd shell nuclei

    Energy Technology Data Exchange (ETDEWEB)

    Ognibene, Theodore Joseph [Lawrence Berkeley National Lab., CA (United States). Nuclear Science Div.

    1996-03-01

    To overcome the extreme difficulties encountered in the experimental decay studies of proton drip line nuclei, several techniques have been utilized, including a helium-jet transport system, particle identification detectors and mass separation. Improvements to the ion source/extraction region of the He-jet coupled on-line Recoil Atom Mass Analyzer (RAMA) and its target/ion source coupling resulted in significant increases in RAMA efficiencies and its mass resolution, as well as reductions in the overall transit time. At the 88-Inch Cyclotron at LBNL, the decays of 31Cl, 27P and 28P, with half-lives of 150 msec, 260 msec and 270.3 msec, respectively, were examined using a he-jet and low-energy gas ΔE-gas ΔE-silicon E detector telescopes. Total beta-delayed proton branches of 0.3% and 0.07% in 31Cl and 27P, respectively, were estimated. Several proton peaks that had been previously assigned to the decay of 31Cl were shown to be from the decay of 25Si. In 27P, two proton groups at 459 ± 14 keV and 610 ± 11 keV, with intensities of 7 ± 3% and 92 ± 4% relative to the main (100%) group were discovered. The Gamow-Teller component of the preceding beta-decay of each observed proton transition was compared to results from shell model calculations. Finally, a new proton transition was identified, following the β-decay of 28P, at 1,444 ± 12 keV with a 1.7 ± 0.5% relative intensity to the 100% group. Using similar low-energy detector telescopes and the mass separator TISOL at TRIUMF, the 109 msec and 173 msec activities, 17Ne and 33Ar, were studied. A new proton group with energy 729 ± 15 keV was observed following the beta-decay of 17Ne. Several discrepancies between earlier works as to the energies, intensities and assignments of several proton transitions from 17Ne and 33Ar were resolved.

  15. Improvements to the on-line mass separator, RAMA, and the beta-delayed charged-particle emission of proton-rich sd shell nuclei

    Energy Technology Data Exchange (ETDEWEB)

    Ognibene, T.J. [Lawrence Berkeley National Lab., CA (United States). Nuclear Science Div.

    1996-03-01

    To overcome the extreme difficulties encountered in the experimental decay studies of proton drip line nuclei, several techniques have been utilized, including a helium-jet transport system, particle identification detectors and mass separation. Improvements to the ion source/extraction region of the He-jet coupled on-line Recoil Atom Mass Analyzer (RAMA) and its target/ion source coupling resulted in significant increases in RAMA efficiencies and its mass resolution, as well as reductions in the overall transit time. At the 88-Inch Cyclotron at LBNL, the decays of {sup 31}Cl, {sup 27}P and {sup 28}P, with half-lives of 150 msec, 260 msec and 270.3 msec, respectively, were examined using a he-jet and low-energy gas {Delta}E-gas {Delta}E-silicon E detector telescopes. Total beta-delayed proton branches of 0.3% and 0.07% in {sup 31}Cl and {sub 27}P, respectively, were estimated. Several proton peaks that had been previously assigned to the decay of {sup 31}Cl were shown to be from the decay of {sup 25}Si. In {sup 27}P, two proton groups at 459 {+-} 14 keV and 610 {+-} 11 keV, with intensities of 7 {+-} 3% and 92 {+-} 4% relative to the main (100%) group were discovered. The Gamow-Teller component of the preceding beta-decay of each observed proton transition was compared to results from shell model calculations. Finally, a new proton transition was identified, following the {beta}-decay of {sup 28}P, at 1,444 {+-} 12 keV with a 1.7 {+-} 0.5% relative intensity to the 100% group. Using similar low-energy detector telescopes and the mass separator TISOL at TRIUMF, the 109 msec and 173 msec activities, {sup 17}Ne and {sup 33}Ar, were studied. A new proton group with energy 729 {+-} 15 keV was observed following the beta-decay of {sup 17}Ne. Several discrepancies between earlier works as to the energies, intensities and assignments of several proton transitions from {sup 17}Ne and {sup 33}Ar were resolved.

  16. Installation for the formation of a laser beam adapted to isotope separation. Installation pour la formation d'un faisceau laser adapte a la separation isotopique

    Energy Technology Data Exchange (ETDEWEB)

    Guyot, J.; Pochon, E.

    1993-04-23

    The present invention claims the formation of a laser beam for isotope separation of an atomic vapor. Pumping is obtained by solid matrix lasers, for instance of the YAG type doubled in frequency and triggered with optical fibers guiding the light towards the tunable dye lasers.

  17. Study of collisions of {sup 136}Xe + {sup 198}Pt for the KEK isotope separator

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, Y.X., E-mail: yutaka.watanabe@kek.jp [Institute of Particle and Nuclear Studies, High Energy Accelerator Research Organization (KEK), 1-1 Oho, Tsukuba, Ibaraki 305-0801 (Japan); Hirayama, Y.; Imai, N.; Ishiyama, H.; Jeong, S.C.; Miyatake, H. [Institute of Particle and Nuclear Studies, High Energy Accelerator Research Organization (KEK), 1-1 Oho, Tsukuba, Ibaraki 305-0801 (Japan); Clement, E.; France, G. de; Navin, A.; Rejmund, M.; Schmitt, C. [Grand Accélérateur National d’Ions Lourds (GANIL), CEA/DSM-CNRS/IN2P3, Bd Henri Becquerel, BP 55027, F-14076 Caen Cedex 05 (France); Pollarolo, G. [Dipartimento di Fisica Teorica, Università di Torino, Via Pietro Giuria 1, 10125 Torino (Italy); Corradi, L.; Fioretto, E. [Laboratori Nazionali di Legnaro dell’INFN, Via Romea 4, 35020 Legnaro (Italy); Montanari, D. [Università di Padova, Via 8 Febbraio, 2-35122 Padova (Italy); Choi, S.H.; Kim, Y.H.; Song, J.S. [Seoul National University, 1 Gwanak-ro, Gwanak-gu, Seoul 151-742 (Korea, Republic of); Niikura, M.; Suzuki, D. [Institut de Physique Nucléaire (IPN), IN2P3-CNRS, Université Paris-Sud 11, F-91406 Orsay Cedex (France); and others

    2013-12-15

    Highlights: • {sup 136}Xe + {sup 198}Pt shows a comparable contribution of proton pick-up and stripping. • Proton stripping channels in {sup 136}Xe + {sup 198}Pt show enhanced cross sections. • Mass distributions of proton stripping channels in {sup 136}Xe + {sup 198}Pt shift to heavy side. -- Abstract: Multinucleon transfer reactions between two heavy ions are an important tool for production and investigation of exotic neutron-rich nuclei, which are difficult to access by other methods. The {sup 136}Xe + {sup 198}Pt system is a candidate to efficiently produce neutron-rich nuclei around the neutron magic number N=126 for the KEK isotope separation project. In order to confirm this, measurements of the production cross sections with the large acceptance magnetic spectrometer VAMOS++ and de-excitation gamma rays from target-like fragments using the high efficiency germanium array EXOGAM at GANIL are reported. The measured isotopic distributions of the projectile-like fragments are compared with GRAZING calculations. The proton stripping channels show rough agreements between measurements and calculations. For the proton pick-up channels, the measured distributions are shifted toward the heavier masses and show enhanced cross sections in transfers of two or more protons.

  18. New triple oxygen isotope data of bulk and separated fractions from SNC meteorites: Evidence for mantle homogeneity of Mars

    Science.gov (United States)

    Ali, Arshad; Jabeen, Iffat; Gregory, David; Verish, Robert; Banerjee, Neil R.

    2016-05-01

    We report precise triple oxygen isotope data of bulk materials and separated fractions of several Shergotty-Nakhla-Chassigny (SNC) meteorites using enhanced laser-assisted fluorination technique. This study shows that SNCs have remarkably identical Δ17O and a narrow range in δ18O values suggesting that these meteorites have assimilated negligibly small surface materials (<5%), which is undetectable in the oxygen isotope compositions reported here. Also, fractionation factors in coexisting silicate mineral pairs (px-ol and mask-ol) further demonstrate isotopic equilibrium at magmatic temperatures. We present a mass-dependent fractionation line for bulk materials with a slope of 0.526 ± 0.016 (1SE) comparable to the slope obtained in an earlier study (0.526 ± 0.013; Franchi et al. 1999). We also present a new Martian fractionation line for SNCs constructed from separated fractions (i.e., pyroxene, olivine, and maskelynite) with a slope of 0.532 ± 0.009 (1SE). The identical fractionation lines run above and parallel to our terrestrial fractionation line with Δ17O = 0.318 ± 0.016‰ (SD) for bulk materials and 0.316 ± 0.009‰ (SD) for separated fractions. The conformity in slopes and Δ17O between bulk materials and separated fractions confirm oxygen isotope homogeneity in the Martian mantle though recent studies suggest that the Martian lithosphere may potentially have multiple oxygen isotope reservoirs.

  19. Carbon isotopes in eclogite and apatite separate from Huangzhen and Shima in SE Dabie

    Institute of Scientific and Technical Information of China (English)

    李一良; 郑永飞; 龚冰; 傅斌

    2000-01-01

    The carbon isotope compositions of high- and ultrahigh-pressure eclogite and apatite separate from Huangzhen and Shima in SE Dabie Mountains were analyzed by EA-MS online technique. The δ13C values of the eclogites cover a wide range of -30.7‰ - +1.5‰, whereasthose of apatites only have a small range of -28.1‰- -21.0‰. Some of the eclogites with thehigh δ13C values suffered retrogressive alteration by CO2-bearing fluids. The low δ13C values of the apatites indicate that the eclogites contain surficial carbon of organic origin. It is concluded that protoliths of the eclogites were exposed to the surface of the Earth, and that the carbon-bearing fluid was depleted in 13C during the eclogite-facies metamorphism.

  20. Carbon isotopes in eclogite and apatite separate from Huangzhen and Shima in SE Dabie

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The carbon isotope compositions of high- and ultrahigh-pressure eclogite and apatite separate from Huangzhen and Shima in SE Dabie Mountains were analyzed by EA-MS online technique. The δ13C values of the eclogites cover a wide range of -30.7‰ - +1.5‰, whereas those of apatites only have a small range of -28.1‰--21.0‰. Some of the eclogites with the high δ13C values suffered retrogressive alteration by CO2-bearing fluids. The low δ13C values of the apatites indicate that the eclogites contain surficial carbon of organic origin. It is concluded that protoliths of the eclogites were exposed to the surface of the Earth, and that the carbon-bearing fluid was depleted in 13C during the eclogite-facies metamorphism.

  1. RADIATION STABILITY OF NAFION MEMBRANES USED FOR ISOTOPE SEPARATION BY PROTON EXCHANGE MEMBRANE ELECTROLYSIS

    Energy Technology Data Exchange (ETDEWEB)

    Fox, E

    2009-05-15

    Proton Exchange Membrane Electrolyzers have potential interest for use for hydrogen isotope separation from water. In order for PEME to be fully utilized, more information is needed on the stability of Nafion when exposed to radiation. This work examines Nafion 117 under varying exposure conditions, including dose rate, total dosage and atmospheric condition. Analytical tools, such as FT-IR, ion exchange capacity, DMA and TIC-TOC were used to characterize the exposed membranes. Analysis of the water from saturated membranes can provide important data on the stability of the membranes during radiation exposure. It was found that the dose rate of exposure plays an important role in membrane degradation. Potential mechanisms for membrane degradation include peroxide formation by free radicals.

  2. Survey of knowledge of hazards of chemicals potentially associated with the advanced isotope separation processes

    Energy Technology Data Exchange (ETDEWEB)

    Chester, R.O.; Kirkscey, K.A.; Randolph, M.L.

    1979-09-01

    Hazards of chemical potentially associated with the advanced isotope separation processes are estimated based on open literature references. The tentative quantity of each chemical associated with the processes and the toxicity of the chemical are used to estimate this hazard. The chemicals thus estimated to be the most potentially hazardous to health are fluorine, nitric acid, uranium metal, uranium hexafluoride, and uranium dust. The estimated next most hazardous chemicals are bromine, hydrobromic acid, hydrochloric acid, and hydrofluoric acid. For each of these chemicals and for a number of other process-associated chemicals the following information is presented: (1) any applicable standards, recommended standards and their basis; (2) a brief discussion to toxic effects including short exposure tolerance, atmospheric concentration immediately hazardous to life, evaluation of exposures, recommended control procedures, chemical properties, and a list of any toxicology reviews; and (3) recommendations for future research.

  3. Spatial variability in the isotopic composition of rainfall in a small headwater catchment and its effect on hydrograph separation

    Science.gov (United States)

    Fischer, Benjamin M. C.; van Meerveld, H. J. (Ilja); Seibert, Jan

    2017-04-01

    Isotope hydrograph separation (IHS) is a valuable tool to study runoff generation processes. To perform an IHS, samples of baseflow (pre-event water) and streamflow are taken at the catchment outlet. For rainfall (event water) either a bulk sample is collected or it is sampled sequentially during the event. For small headwater catchment studies, event water samples are usually taken at only one sampling location in or near the catchment because the spatial variability in the isotopic composition of rainfall is assumed to be small. However, few studies have tested this assumption. In this study, we investigated the spatiotemporal variability in the isotopic composition of rainfall and its effects on IHS results using detailed measurements from a small pre-alpine headwater catchment in Switzerland. Rainfall was sampled sequentially at eight locations across the 4.3 km2 Zwäckentobel catchment and stream water was collected in three subcatchments (0.15, 0.23, and 0.70 km2) during ten events. The spatial variability in rainfall amount, average and maximum rainfall intensity and the isotopic composition of rainfall was different for each event. There was no significant relation between the isotopic composition of rainfall and total rainfall amount, rainfall intensity or elevation. For eight of the ten studied events the temporal variability in the isotopic composition of rainfall was larger than the spatial variability in the rainfall isotopic composition. The isotope hydrograph separation results, using only one rain sampler, varied considerably depending on which rain sampler was used to represent the isotopic composition of event water. The calculated minimum pre-event water contributions differed up to 60%. The differences were particularly large for events with a large spatial variability in the isotopic composition of rainfall and a small difference between the event and pre-event water isotopic composition. Our results demonstrate that even in small catchments

  4. 10 CFR Appendix N to Part 110 - Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment Under NRC's...

    Science.gov (United States)

    2010-01-01

    ..., Plants and Equipment Under NRC's Export Licensing Authority N Appendix N to Part 110 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) EXPORT AND IMPORT OF NUCLEAR EQUIPMENT AND MATERIAL Pt. 110, App. N Appendix N to Part 110—Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment...

  5. New on-line method for water isotope analysis of fluid inclusions in speleothems using laser absorption spectroscopy: Application to stalagmites from Borneo and Switzerland

    Science.gov (United States)

    Affolter, Stéphane; Fleitmann, Dominik; Nele Meckler, Anna; Leuenberger, Markus

    2014-05-01

    Speleothems are recognised as key continental archives for paleoclimate reconstructions. They contain fluid inclusions representing past drip water trapped in the calcite structure. Speleothem can be precisely dated and therefore the oxygen (δ18O) and hydrogen (δD) isotopes of fluid inclusions constitute powerful proxies for paleotemperature or to investigate changes in the moisture source over several interglacial-glacial cycles. To liberate fluid inclusion water and to analyse its isotopic composition, a new online extraction method developed at Bern is used. The principle can be summarised as follows: Prior to crushing, the sample is placed into a copper tube, fixed to the line previously heated to 140° C and flushed with a nitrogen and standard water mixture. Thereafter, the speleothem sample is crushed using a simple hydraulic crushing device and the released water from fluid inclusions is transferred by the nitrogen-standard water mixture flow to a Picarro L1102-i isotopic liquid water and water vapor analyser. The measuring principle is based on wavelength-scanned cavity ring-down spectroscopy (WS-CRDS) technology that allows us to simultaneously monitor hydrogen and oxygen isotopes. Reproducibility of standard water measurements is typically better than 1.5 o for δD and 0.4 o for δ18O. With this method, we successfully analysed δD and δ18O isotopic composition of a stalagmite from Northern Borneo (tropical West Pacific) covering almost two glacial-interglacial cycles from MIS 12 to early MIS 9 (460-330 ka) as well as recent samples from Switzerland and Borneo. These results are used in combination with calcite δ18O to reconstruct paleotemperature. Currently, we are measuring a stalagmite from Milandre cave (Jura, Switzerland) covering the Bølling-Allerød, Younger Dryas cold phase and the Holocene.

  6. On-line solid phase extraction-high performance liquid chromatography–isotope dilution–tandem mass spectrometry approach to quantify N,N-diethyl-m-toluamide and oxidative metabolites in urine

    Energy Technology Data Exchange (ETDEWEB)

    Kuklenyik, Peter; Baker, Samuel E.; Bishop, Amanda M.; Morales-A, Pilar; Calafat, Antonia M., E-mail: aic7@cdc.gov

    2013-07-17

    Graphical abstract: -- Highlights: •A fast assay to quantify the concentrations of N,N-Diethyl-m-Toluamide and two urinary metabolites was developed •It uses online SPE, reversed phase HPLC and tandem mass spectrometry •The method is precise and accurate with limits of detection ≤1 ng mL{sup −1} -- Abstract: Human exposure to N,N-diethyl-m-toluamide (DEET) occurs because of the widespread use of DEET as an active ingredient in insect repellents. However, information on the extent of such exposure is rather limited. Therefore, we developed a fast on-line solid phase extraction–high performance liquid chromatography–isotope dilution tandem mass spectrometry (HPLC-MS/MS) method to measure in urine the concentrations of DEET and two of its oxidative metabolites: N,N-diethyl-3-(hydroxymethyl)benzamide and 3-(diethylcarbamoyl)benzoic acid (DCBA). To the best of our knowledge, this is the first HPLC-MS/MS method for the simultaneous quantification of DEET and its select metabolites in human urine. After enzymatic hydrolysis of the conjugated species in 0.1 mL of urine, the target analytes were retained and pre-concentrated on a monolithic column, separated from each other and from other urinary biomolecules on a reversed-phase analytical column, and detected by atmospheric pressure chemical ionization in positive ion mode. The limits of detection ranged from 0.1 ng mL{sup −1} to 1.0 ng mL{sup −1}, depending on the analyte. Accuracy ranged between 90.4 and 104.9%, and precision ranged between 5.5 and 13.1% RSD, depending on the analyte and the concentration. We tested the usefulness of this method by analyzing 75 urine samples collected anonymously in the Southeastern United States in June 2012 from adults with no known exposure to DEET. Thirty eight samples (51%) tested positive for at least one of the analytes. We detected DCBA most frequently and at the highest concentrations. Our results suggest that this method can be used for the analysis of a large

  7. Cryogenic separation of an oxygen-argon mixture in natural air samples for the determination of isotope and molecular ratios.

    Science.gov (United States)

    Keedakkadan, Habeeb Rahman; Abe, Osamu

    2015-04-30

    The separation and purification of oxygen-argon mixtures are critical in the high-precision analysis of Δ(17) O and δ(O2 /Ar) for geochemical applications. At present, chromatographic methods are used for the separation and purification of oxygen-argon mixtures or pure oxygen, but these methods require the use of high-purity helium as a carrier gas. Considerable interest has been expressed in the development of a helium-free cryogenic separation of oxygen-argon mixtures in natural air samples. The precise and simplified cryogenic separation of oxygen-argon mixtures from natural air samples presented here was made possible using a single 5A (30/60 mesh) molecular sieve column. The method involves the trapping of eluted gases using molecular sieves at liquid nitrogen temperature, which is associated with isotopic fractionation. We tested the proposed method for the determination of isotopic fractionations during the gas exchange between water and atmospheric air at equilibrium. The dependency of fractionation was studied at different water temperatures and for different methods of equilibration (bubbling and stirring). Isotopic and molecular fractionations during gas desorption from molecular sieves were studied for different amounts and types of molecular sieves. Repeated measurements of atmospheric air yielded a reproducibility (±SD) of 0.021 ‰, 0.044 ‰, 15 per meg and 1.9 ‰ for δ(17) O, δ(18) O, Δ(17) O and δ(O2 /Ar) values, respectively. We applied the method to determine equilibrium isotope fractionation during gas exchange between air and water. Consistent δ(18) O and Δ(17) O results were obtained with the latest two studies, whereas there was a significant difference in δ(18) O values between seawater and deionized water. We have revised a helium-free, cryogenic separation of oxygen-argon mixtures in natural air samples for isotopic and molecular ratio analysis. The use of a single 13X (1/8" pellet) molecular sieve yielded the smallest isotopic

  8. The importance of snowmelt spatiotemporal variability for isotope-based hydrograph separation in a high-elevation catchment

    Science.gov (United States)

    Schmieder, Jan; Hanzer, Florian; Marke, Thomas; Garvelmann, Jakob; Warscher, Michael; Kunstmann, Harald; Strasser, Ulrich

    2016-12-01

    Seasonal snow cover is an important temporary water storage in high-elevation regions. Especially in remote areas, the available data are often insufficient to accurately quantify snowmelt contributions to streamflow. The limited knowledge about the spatiotemporal variability of the snowmelt isotopic composition, as well as pronounced spatial variation in snowmelt rates, leads to high uncertainties in applying the isotope-based hydrograph separation method. The stable isotopic signatures of snowmelt water samples collected during two spring 2014 snowmelt events at a north- and a south-facing slope were volume weighted with snowmelt rates derived from a distributed physics-based snow model in order to transfer the measured plot-scale isotopic composition of snowmelt to the catchment scale. The observed δ18O values and modeled snowmelt rates showed distinct inter- and intra-event variations, as well as marked differences between north- and south-facing slopes. Accounting for these differences, two-component isotopic hydrograph separation revealed snowmelt contributions to streamflow of 35 ± 3 and 75 ± 14 % for the early and peak melt season, respectively. These values differed from those determined by formerly used weighting methods (e.g., using observed plot-scale melt rates) or considering either the north- or south-facing slope by up to 5 and 15 %, respectively.

  9. Separation of seven arsenic compounds by high-performance liquid chromatography with on-line detection by hydrogen–argon flame atomic absorption spectrometry and inductively coupled plasma mass spectrometry

    DEFF Research Database (Denmark)

    Hansen, S. H.; Larsen, E. H.; Pritzl, G.

    1992-01-01

    Seven molecular forms of arsenic were separated by anion- and cation-exchange high-performance liquid chromatography (HPLC) with on-line detection by flame atomic absorption spectrometry (FAAS). The interfacing was established by a vented poly(tetrafluoroethylene) capillary tubing connecting...... the HPLC column to the nebulizer of the atomic absorption spectrometer. Arsenite, arsenate, monomethylarsonate (MMA) and dimethylarsinate (DMA) were separated from each other and from the co-injected cationic arsenic compounds, arsenobetaine (AsB), arsenocholine (AsC) and the tetramethylarsonium ion (TMAs......-to-noise ratio of the on-line AAS detector was optimized. This involved the use of the hydrogen-argon-entrained air flame, a slotted tube atom trap in the flame for signal enhancement, electronic noise damping and a high-intensity light source. The detection limits in mu-g cm-3, using 100 mm3 injections...

  10. Separation of seven arsenic compounds by high performance liquid chromatography with on-line detection by hydrogen-argon flame atomic absorption spectrometry and inductively coupled plasma mass spectrometry

    DEFF Research Database (Denmark)

    Hansen, S. H.; Larsen, Erik Huusfeldt; Pritzl, G.

    1992-01-01

    Seven molecular forms of arsenic were separated by anion- and cation-exchange high-performance liquid chromatography (HPLC) with on-line detection by flame atomic absorption spectrometry (FAAS). The interfacing was established by a vented poly(tetrafluoroethylene) capillary tubing connecting......-to-noise ratio of the on-line AAS detector was optimized. This involved the use of the hydrogen-argon-entrained air flame, a slotted tube atom trap in the flame for signal enhancement, electronic noise damping and a high-intensity light source. The detection limits in mu-g cm-3, using 100 mm3 injections...... the HPLC column to the nebulizer of the atomic absorption spectrometer. Arsenite, arsenate, monomethylarsonate (MMA) and dimethylarsinate (DMA) were separated from each other and from the co-injected cationic arsenic compounds, arsenobetaine (AsB), arsenocholine (AsC) and the tetramethylarsonium ion (TMAs...

  11. Optimization and comparison of simultaneous and separate acquisition protocols for dual isotope myocardial perfusion SPECT

    Science.gov (United States)

    Ghaly, Michael; Links, Jonathan M.; Frey, Eric C.

    2015-07-01

    Dual-isotope simultaneous-acquisition (DISA) rest-stress myocardial perfusion SPECT (MPS) protocols offer a number of advantages over separate acquisition. However, crosstalk contamination due to scatter in the patient and interactions in the collimator degrade image quality. Compensation can reduce the effects of crosstalk, but does not entirely eliminate image degradations. Optimizing acquisition parameters could further reduce the impact of crosstalk. In this paper we investigate the optimization of the rest Tl-201 energy window width and relative injected activities using the ideal observer (IO), a realistic digital phantom population and Monte Carlo (MC) simulated Tc-99m and Tl-201 projections as a means to improve image quality. We compared performance on a perfusion defect detection task for Tl-201 acquisition energy window widths varying from 4 to 40 keV centered at 72 keV for a camera with a 9% energy resolution. We also investigated 7 different relative injected activities, defined as the ratio of Tc-99m and Tl-201 activities, while keeping the total effective dose constant at 13.5 mSv. For each energy window and relative injected activity, we computed the IO test statistics using a Markov chain Monte Carlo (MCMC) method for an ensemble of 1,620 triplets of fixed and reversible defect-present, and defect-absent noisy images modeling realistic background variations. The volume under the 3-class receiver operating characteristic (ROC) surface (VUS) was estimated and served as the figure of merit. For simultaneous acquisition, the IO suggested that relative Tc-to-Tl injected activity ratios of 2.6-5 and acquisition energy window widths of 16-22% were optimal. For separate acquisition, we observed a broad range of optimal relative injected activities from 2.6 to 12.1 and acquisition energy window of widths 16-22%. A negative correlation between Tl-201 injected activity and the width of the Tl-201 energy window was observed in these ranges. The results

  12. Hydrograph separation using stable isotopes, silica and electrical conductivity: an alpine example

    Science.gov (United States)

    Laudon, Hjalmar; Slaymaker, Olav

    1997-12-01

    Hydrograph separation of runoff events in two nested alpine/subalpine basins in the Coast Mountains of British Columbia was carried out using electrical conductivity, specific concentration of silica and the stable isotopes oxygen-18 and deuterium as hydrological tracers. The methods predicted consistent high pre-storm water contribution for the subalpine site (60-90%) but more variable contribution at the alpine basin outlet (25-90%). The pre-storm water contribution is much larger than had previously been expected. Precipitation is believed to run off as overland flow due to the steep slopes in combination with the hydrophobic soils until it can enter the subsurface environment. The rapid influx of stored water is possibly caused by pressure propagation in the macropore system which could be enhanced by the heavily fractured bedrock and permeable landslide debris acting as efficient hydrological conduits. The study suggests that alternative hydrological tracers such as electrical conductivity and silica concentration can be used under certain hydrological and lithological conditions. These alternative tracers should, however, be verified against more conventional tracers before use, as the behaviour depends on specific characteristics of each basin. At the upper basin outlet, both electrical conductivity (EC) and silica underestimated the pre-storm contribution. At the lower station, silica and EC showed a similar pattern to deuterium and oxygen-18 tracers. The calculated pre-storm component using EC was, however, 10-20% lower than the calculated values from the other three tracers. The advantage of using these alternative tracers is that hydrograph separation results can, a priori, be anticipated.

  13. Preparative separation of arsenate from phosphate by IRA-400 (OH) for oxygen isotopic work.

    Science.gov (United States)

    Tang, Xiaohui; Berner, Zsolt; Khelashvilli, Pirimze; Norra, Stefan

    2013-02-15

    The paper reports about a series of tests carried out to find out the optimal conditions for the preparative separation of arsenate and phosphate from natural waters, using the anion exchange resin Amberlite IRA-400 (OH). Freundlich isotherms have been constructed on basis of data obtained by stirring different amounts of resin (0.05-1.00 g) with solutions containing 1mg/L As and 10mg/L P in form of arsenate and phosphate and the effect of pH and P/As ratio on adsorption was investigated. It was found that at these concentrations 0.5 g of IRA-400 (OH) can adsorb quantitatively arsenate and phosphate within 1h. In a range of 3.6-11.1, pH seems to have no influence on the adsorption behavior of the resin, but at pH 1.5 the adsorption of both arsenate and phosphate drops to values close to zero. Experiments with solutions with P/As ratios in a range between 1 and 30 have shown that the concentration ratios have also little effect on adsorption. An efficient selective desorption of the anions could be achieved with 2 mol/L HNO3 or HCl, but the use of HCl is impracticable if the separation aims at precipitating arsenate for oxygen isotopic work. The reported adsorption/ desorption properties of the resin are supported also by data obtained by investigating the resin particles with a scanning electron microscope equipped with a fluorescence detection device.

  14. Multikilowatt TEA-CO2 laser system for molecular laser isotope separation

    Science.gov (United States)

    Ronander, Einar; Rohwer, Erich G.

    1993-05-01

    Laser-induced chemistry has received much attention in the past few years. The economics of such applications are dominated by the costs of photons and the quantum yield of the specific reaction. For a typical multiple-IR-photon process the quantum yield can be as low as 10-4 which emphasizes the importance of reducing the cost of laser photons. Based on 1982 technology, CO2 TEA laser operating costs were approximately $100/watt per year for a laser with an electrical efficiency of 6% and an average power of more than 100 kW. Capital costs dominated the energy cost as well as the maintenance and labor costs. At the South African Atomic Energy Corp. we have been involved in the development of high pulse frequency, high average power TEA-CO2 lasers for the application in the field of laser-induced chemistry. Much of the attention, however, has been focused on the application to separate the isotopes of uranium via a multiwavelength infrared irradiation scheme. The progress that has been made towards the establishment of CO2-lasers and laser chains for industrial use has been quite outstanding.

  15. Tunable lasers in isotope separation: a colorful view of a dye chemist

    Energy Technology Data Exchange (ETDEWEB)

    Hammond, P.R.

    1977-07-01

    Some of the problems to be encountered in the possible large scale use of dye lasers in an isotope separation plant are discussed.The effect of laser dye deterioration on performance is examined algebraically in terms of disappearance of dye molecules and the appearance of a new, single chemical product having absorption in the fluorescence band for a single pass through a transversely pumped amplifier. Loss of output, defined as ''quantum yield of laser deterioration'', Q/sub L/, is related to the true quantum yield of molecular destruction of the dye Q/sub M/, and other known parameters. 6-Diethylamino 3-keto fluoran, an example of an oxygen tricyclic merocyanine, is described. It was first reported in the pre-1900 German literature under the name of Chromogen Red B and it is an ineffective lasing dye on account of low fluorescence quantum yield. The techniques for measurement and the excited state absorption cross-sections are reported for the dyes rhodamine 6G fluoroborate in alcohol, rhodamine B basic solution in trifluoroethanol and kiton red S in trifluoroethanol.

  16. Isotope separation of silicon and molybdenum using a free electron laser

    Energy Technology Data Exchange (ETDEWEB)

    Noda, Tetsuji E-mail: noda.tetsuji@nims.go.jp; Suzuki, Hiroshi; Araki, Hiroshi; Lyman, John L.; Newnam, Brian E

    2002-12-01

    The isotope separation of silicon and molybdenum was studied with a free electron laser (FEL). The FEL was used to irradiate flowing Si{sub 2}F{sub 6} between 1000 and 800 cm{sup -1} wavenumbers and to irradiate MoF{sub 6} at 740 cm{sup -1}. Enrichments of {sup 29}Si and {sup 30}Si were detected by 1000 cm{sup -1} irradiation. A similar tendency with the {sup 29}Si and {sup 30}Si concentration as a function of the wavenumber resulted with a CO{sub 2} laser irradiation. The maximum concentration occurred at around 950-955 cm{sup -1} for {sup 30}Si and 960 cm{sup -1} for {sup 29}Si. The concentration of {sup 29}Si was also detected at 800 cm{sup -1} band. {sup 98}MoF{sub 6} and {sup 100}MoF{sub 6} were selectively decomposed and {sup 92}Mo and {sup 94}Mo were concentrated in the residual gas after the FEL irradiation at 728 cm{sup -1} but the enrichment was small.

  17. Optimization of on-line hydrogen stable isotope ratio measurements of halogen- and sulfur-bearing organic compounds using elemental analyzer–chromium/high-temperature conversion isotope ratio mass spectrometry (EA-Cr/HTC-IRMS)

    Science.gov (United States)

    Gehre, Matthias; Renpenning, Julian; Geilmann, Heike; Qi, Haiping; Coplen, Tyler B.; Kümmel, Steffen; Ivdra, Natalija; Brand, Willi A.; Schimmelmann, Arndt

    2017-01-01

    Rationale: Accurate hydrogen isotopic analysis of halogen- and sulfur-bearing organics has not been possible with traditional high-temperature conversion (HTC) because the formation of hydrogen-bearing reaction products other than molecular hydrogen (H2) is responsible for non-quantitative H2 yields and possible hydrogen isotopic fractionation. Our previously introduced, new chromium-based EA-Cr/HTC-IRMS (Elemental Analyzer–Chromium/High-Temperature Conversion Isotope Ratio Mass Spectrometry) technique focused primarily on nitrogen-bearing compounds. Several technical and analytical issues concerning halogen- and sulfur-bearing samples, however, remained unresolved and required further refinement of the reactor systems.

  18. Economic study of an installation for uranium isotope separation by gaseous diffusion; Etude economique d'une installation de separation des isotopes de l'uranium par diffusion gazeuse

    Energy Technology Data Exchange (ETDEWEB)

    Bilous, O. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    This report describes the major problems which arise in the choice of characteristics required in a gaseous diffusion installation for the separation of uranium isotopes. This choice depends largely on economic evaluations, and also on considerations of simplicity. The choice of working pressures and of the characteristics of the membrane are described, as are the possible alternatives regarding the structure of the stages and the problems of control. (author) [French] Ce rapport decrit les problemes majeurs qui se posent dans le choix des caracteristiques d'une installation de diffusion gazeuse destinee a la separation des isotopes de l'uranium. Ce choix depend en grande partie d'evaluations economiques et repose egalement sur des considerations de simplicite. On decrit ainsi le choix des pressions d'operation, celui des caracteristiques de la barriere, les alternatives possibles concernant la structure des etages et les problemes de regulation. (auteur)

  19. Production cross section measurements of radioactive isotopes by BigRIPS separator at RIKEN RI Beam Factory

    CERN Document Server

    Suzuki, H; Fukuda, N; Inabe, N; Kameda, D; Takeda, H; Yoshida, K; Kusaka, K; Yanagisawa, Y; Ohtake, M; Sato, H; Shimizu, Y; Baba, H; Kurokawa, M; Ohnishi, T; Tanaka, K; Tarasov, O B; Bazin, D; Morrissey, D J; Sherrill, B M; Ieki, K; Murai, D; Iwasa, N; Chiba, A; Ohkoda, Y; Ideguchi, E; Go, S; Yokoyama, R; Fujii, T; Nishimura, D; Nishibata, H; Momota, S; Lewitowicz, M; DeFrance, G; Celikovic, I; Steiger, K

    2013-01-01

    We have measured the production rates and production cross sections for a variety of radioactive isotopes which were produced from 124Xe, 48Ca, and 238U beams at an energy of 345 MeV/nucleon using the BigRIPS separator at the RIKEN Nishina Center RI Beam Factory (RIBF). Proton-rich isotopes with atomic numbers Z = 40 to 52 and neutron-rich isotopes with Z = 5 to 16 were produced by projectile fragmentation of the 124Xe and 48Ca beam on Be targets, respectively. Neutron-rich isotopes with Z = 20 to 59 were produced by in-flight fission of the 238U beam, in which both Be and Pb were used as production targets. The measured production rates and production cross sections were compared with those of the LISE++ calculations, and overall fairly good agreement has been obtained. Furthermore, in the measurements with the 124Xe beam, we have discovered four new isotopes on the proton-drip line, 85,86Ru and 81,82Mo, and obtained the clear evidence that 103Sb is particle unbound with an upper limit of 49 ns for the half-...

  20. New on-line separation workflow of microbial metabolites via hyphenation of analytical and preparative comprehensive two-dimensional liquid chromatography.

    Science.gov (United States)

    Yan, Xia; Wang, Li-Juan; Wu, Zhen; Wu, Yun-Long; Liu, Xiu-Xiu; Chang, Fang-Rong; Fang, Mei-Juan; Qiu, Ying-Kun

    2016-10-15

    Microbial metabolites represent an important source of bioactive natural products, but always exhibit diverse of chemical structures or complicated chemical composition with low active ingredients content. Traditional separation methods rely mainly on off-line combination of open-column chromatography and preparative high performance liquid chromatography (HPLC). However, the multi-step and prolonged separation procedure might lead to exposure to oxygen and structural transformation of metabolites. In the present work, a new two-dimensional separation workflow for fast isolation and analysis of microbial metabolites from Chaetomium globosum SNSHI-5, a cytotoxic fungus derived from extreme environment. The advantage of this analytical comprehensive two-dimensional liquid chromatography (2D-LC) lies on its ability to analyze the composition of the metabolites, and to optimize the separation conditions for the preparative 2D-LC. Furthermore, gram scale preparative 2D-LC separation of the crude fungus extract could be performed on a medium-pressure liquid chromatograph×preparative high-performance liquid chromatography system, under the optimized condition. Interestingly, 12 cytochalasan derivatives, including two new compounds named cytoglobosin Ab (3) and isochaetoglobosin Db (8), were successfully obtained with high purity in a short period of time. The structures of the isolated metabolites were comprehensively characterized by HR ESI-MS and NMR. To be highlighted, this is the first report on the combination of analytical and preparative 2D-LC for the separation of microbial metabolites. The new workflow exhibited apparent advantages in separation efficiency and sample treatment capacity compared with conventional methods.

  1. Determination of Hg{sup 2+} by on-line separation and pre-concentration with atmospheric-pressure solution-cathode glow discharge atomic emission spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Li, Qing [Shanghai Institute of Ceramics, Chinese Academy of Science, Shanghai 200050 (China); Zhang, Zhen [Shanghai Institute of Ceramics, Chinese Academy of Science, Shanghai 200050 (China); School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China); Wang, Zheng, E-mail: wangzheng@mail.sic.ac.cn [Shanghai Institute of Ceramics, Chinese Academy of Science, Shanghai 200050 (China)

    2014-10-03

    Highlights: • A modified SBA-15 mesoporous silica (SH-SBA-15) was synthesized as a sorbent. • On-line SPE combined with SCGD-AES based on FIA was used to detect Hg{sup 2+} firstly. • A simple, low-cost Hg{sup 2+} analysis in a complex matrix was established. • The sensitive detection of Hg{sup 2+} was achieved with a detection limit of 0.75 μg L{sup −1}. - Abstract: A simple and sensitive method to determine Hg{sup 2+} was developed by combining solution-cathode glow discharge atomic emission spectrometry (SCGD-AES) with flow injection (FI) based on on-line solid-phase extraction (SPE). We synthesized L-cysteine-modified mesoporous silica and packed it in an SPE microcolumn, which was experimentally determined to possess a good mercury adsorption capacity. An enrichment factor of 42 was achieved under optimized Hg{sup 2+} elution conditions, namely, an FI flow rate of 2.0 mL min{sup −1} and an eluent comprised of 10% thiourea in 0.2 mol L{sup −1} HNO{sub 3}. The detection limit of FI–SCGD-AES was determined to be 0.75 μg L{sup −1}, and the precision of the 11 replicate Hg{sup 2+} measurements was 0.86% at a concentration of 100 μg L{sup −1}. The proposed method was validated by determining Hg{sup 2+} in certified reference materials such as human hair (GBW09101b) and stream sediment (GBW07310)

  2. Peptide separations by on-line MudPIT compared to isoelectric focusing in an off-gel format: application to a membrane-enriched fraction from C2C12 mouse skeletal muscle cells.

    Science.gov (United States)

    Elschenbroich, Sarah; Ignatchenko, Vladimir; Sharma, Parveen; Schmitt-Ulms, Gerold; Gramolini, Anthony O; Kislinger, Thomas

    2009-10-01

    High-resolution peptide separation is pivotal for successful shotgun proteomics. The need for capable techniques propels invention and improvement of ever more sophisticated approaches. Recently, Agilent Technologies has introduced the OFFGEL fractionator, which conducts peptide separation by isoelectric focusing in an off-gel setup. This platform has been shown to accomplish high resolution of peptides for diverse sample types, yielding valuable advantages over comparable separation techniques. In this study, we deliver the first comparison of the newly emerging OFFGEL approach to the well-established on-line MudPIT platform. Samples from a membrane-enriched fraction isolated from murine C2C12 cells were subjected to replicate analysis by OFFGEL (12 fractions, pH 3-10) followed by RP-LC-MS/MS or 12-step on-line MudPIT. OFFGEL analyses yielded 1398 proteins (identified by 10,269 peptides), while 1428 proteins (11,078 peptides) were detected with the MudPIT approach. Thus, our data shows that both platforms produce highly comparable results in terms of protein/peptide identifications and reproducibility for the sample type analyzed. We achieve more accurate peptide focusing after OFFGEL fractionation with 88% of all peptides binned to a single fraction, as compared to 61% of peptides detected in only one step in MudPIT analyses. Our study suggests that both platforms are equally capable of high quality peptide separation of a sample with medium complexity, rendering them comparably valuable for comprehensive proteomic analyses.

  3. Coupling Optimization Design and Experimental Study on Stable Isotope 13C Separation of the Double-stage Cascade

    OpenAIRE

    TIAN Ye-sheng;LI Hu-lin;JIANG Yong-yue;LONG Lei;JI Yong-zhe;ZHOU Jian-yue

    2016-01-01

    A coupling optimization design and experimental study method with uniform experimental and Aspen process simulation was established in this paper, which was used for stable isotope 13C separation of the double-stage cascade. Based on the above method, the optimization operating parameters were received. The coupling optimization simulation value showed good agreement with the experimental dates, and the average relative error was only 6.5%. On the other hand, compared with the initial test re...

  4. On-line simultaneous and rapid separation of anions and cations from a single sample using dual-capillary sequential injection-capillary electrophoresis.

    Science.gov (United States)

    Gaudry, Adam J; Guijt, Rosanne M; Macka, Mirek; Hutchinson, Joseph P; Johns, Cameron; Hilder, Emily F; Dicinoski, Greg W; Nesterenko, Pavel N; Haddad, Paul R; Breadmore, Michael C

    2013-06-05

    A novel capillary electrophoresis (CE) approach has been developed for the simultaneous rapid separation and identification of common environmental inorganic anions and cations from a single sample injection. The method utilised a sequential injection-capillary electrophoresis instrument (SI-CE) with capacitively-coupled contactless conductivity detection (C(4)D) constructed in-house from commercial-off-the-shelf components. Oppositely charged analytes from a single sample plug were simultaneously injected electrokinetically onto two separate capillaries for independent separation and detection. Injection was automated and may occur from a syringe or be directly coupled to an external source in a continuous manner. Software control enabled high sample throughput (17 runs per hour for the target analyte set) and the inclusion of an isolation valve allowed the separation capillaries to be flushed, increasing throughput by removing slow migrating species as well as improving repeatability. Various environmental and industrial samples (subjected only to filtering) were analysed in the laboratory with a 3 min analysis time which allowed the separation of 23 inorganic and small organic anions and cations. Finally, the system was applied to an extended automated analysis of Hobart Southern Water tap water for a period of 48 h. The overall repeatability of the migration times of a 14 analyte standard sample was less than 0.74% under laboratory conditions. LODs ranged from 5 to 61 μg L(-1). The combination of automation, high confidence of peak identification, and low limits of detection make this a useful system for the simultaneous identification of a range of common inorganic anions and cations for discrete or continuous monitoring applications.

  5. Stable isotopic internal standard correction for quantitative analysis of hydroxyeicosatetraenoic acids (HETEs) in serum by on-line SPE-LC-MS/MS in selected reaction monitoring mode.

    Science.gov (United States)

    Fernández-Peralbo, M A; Ferreiro Vera, C; Priego-Capote, F; Luque de Castro, M D

    2014-08-01

    The influence of the inclusion of a stable isotopic labeled internal standard (SIL-IS) on the quantitative analysis of hydroxyeicosatetranoic acids (HETEs) in human serum is evaluated in this research. A solid-phase extraction-liquid chromatography-tandem mass spectrometry (SPE-LC-MS/MS) platform, one of the preferred approaches for targeted analysis of biofluids through the selected reaction monitoring (SRM) operational mode, was used to determine HETEs. These compounds were chosen as targeted metabolites because of their involvement in cardiovascular disease, cancer and osteoporosis. 15HETE-d8 was chosen as internal standard to evaluate matrix effects. Thus, the physico-chemical properties of the SIL-IS were the basis to evaluate the analytical features of the method for each metabolite through four calibration models. Two of the models were built with standard solutions at different concentration levels, but one of the calibration sets was spiked with an internal standard (IS). The other two models were built with the serum pool from osteoporotic patients, which was spiked at different concentrations with the target analytes. In this case, one of the serum calibration sets was also spiked with the IS. The study shows that the IS allowed noticeable correction of matrix effects for some HETE isomers at certain concentration levels, while accuracy was decreased at low concentration (15ng/mL) of them. Therefore, characterization of the method has been properly completed at different concentration levels. Copyright © 2014 Elsevier B.V. All rights reserved.

  6. Determination of Hg(2+) by on-line separation and pre-concentration with atmospheric-pressure solution-cathode glow discharge atomic emission spectrometry.

    Science.gov (United States)

    Li, Qing; Zhang, Zhen; Wang, Zheng

    2014-10-03

    A simple and sensitive method to determine Hg(2+) was developed by combining solution-cathode glow discharge atomic emission spectrometry (SCGD-AES) with flow injection (FI) based on on-line solid-phase extraction (SPE). We synthesized l-cysteine-modified mesoporous silica and packed it in an SPE microcolumn, which was experimentally determined to possess a good mercury adsorption capacity. An enrichment factor of 42 was achieved under optimized Hg(2+) elution conditions, namely, an FI flow rate of 2.0 mL min(-1) and an eluent comprised of 10% thiourea in 0.2 mol L(-1) HNO3. The detection limit of FI-SCGD-AES was determined to be 0.75 μg L(-1), and the precision of the 11 replicate Hg(2+) measurements was 0.86% at a concentration of 100 μg L(-1). The proposed method was validated by determining Hg(2+) in certified reference materials such as human hair (GBW09101b) and stream sediment (GBW07310).

  7. Practice of centrifugal stable isotope separation for experiments in neutrino physics

    Energy Technology Data Exchange (ETDEWEB)

    Tikhomirov, A.V. [Kurchatov Institute, Moscow (Russian Federation)

    1994-12-31

    Results of xenon 136, germanium 76 and chromium 50 enrichment with the use of centrifuge cascades are presented. The isotopes are meant for use in experiments in neutrino physics. Tens of kilograms of these isotopes have been produced in Russia, with an enrichment level of an order of magnitude or higher with respect to their natural content. Practical possibilities of using the centrifugal technique both for neutrino investigation and other applications are outlined. 2 tabs., 9 refs.

  8. L-histidine functionalized multi-walled carbon nanotubes for on-line affinity separation and purification of immunoglobulin G in serum.

    Science.gov (United States)

    Du, Zhuo; Zhang, Suling; Zhou, Chanyuan; Liu, Miao; Li, Gongke

    2012-09-15

    In this work, the multi-walled carbon nanotubes were covalently functionalized with L-histidine (His-MWNTs) as online pseudospecific affinity adsorbent for immunoglobulin G (IgG) separation and purification with a simple surface modification method, using 1-ethyl-3-(3-dimethyaminopropyl) carbodiimide hydrochloride (EDC) and N-hydroxysuccinimde (NHS). The affinity of the His-MWNTs toward IgG was investigated in a microcolumn incorporated into a sequential injection system, which also involves an UV spectrometer with a flow cell for online real-time detection. The incorporation of histidine as affinity groups noticeably increased the selectivity and binding capacity of MWNTs for IgG and the His-MWNTs exhibited high retention and recovery rate of nearly 100% under optimized conditions. This separation and enrichment process made it possible to determine a lower concentration range of IgG in serum from 1.0-33 μg/mL with a detection limit of 0.3 μg/mL with a sampling volume of 4.0 mL. The static and dynamic adsorption capacities obtained were 267 mg of IgG/g His-MWNTs and 35 mg/g in aqueous solution, respectively, which are among the highest reported results in literatures employing affinity separation methods. Desorption of IgG from His-MWNTs could be accomplished by lowering the pH to 1.5 with glycine-HCl buffer. The practical application of His-MWNTs for separation of IgG in serum was evaluated with sodium dodecyl sulfate-polyacrylamide gel electrophoresis which confirmed that the purity of recovered IgG from human serum was over 85% and better than a commercial product.

  9. On-line extractive separation in flow injection analysis based on polymer inclusion membranes: a study on membrane stability and approaches for improving membrane permeability.

    Science.gov (United States)

    Zhang, Lujia L; Cattrall, Robert W; Ashokkumar, Muthupandian; Kolev, Spas D

    2012-08-15

    The effect of temperature on the sensitivity and sampling rate is studied for a flow injection analysis (FIA) system that uses a membrane separation cell fitted with a polymer inclusion membrane (PIM) for the determination of Zn(II). A temperature of 50 °C for the flowing donor and acceptor solutions and the membrane separation cell improves the sensitivity and the sampling rate relative to 20 °C up to 10-fold and 2-fold, respectively. Studies on the stability of the PIM are reported that show a limited loss of the membrane liquid phase into the aqueous phases used in the FIA system but this has exhibited a negligible effect on the amount of Zn(II) transported across the membrane. Most importantly, the extent of leaching of the PIM components is shown to depend on the nature of the aqueous phase with the membrane eventually reaching a stable composition. It is also shown that the application of ultrasound to the membrane separation cell leads to a slight increase in sensitivity without affecting the long term membrane stability.

  10. Characteristics of water isotopes and hydrograph separation during the spring flood period in Yushugou River basin, Eastern Tianshans, China

    Indian Academy of Sciences (India)

    Xiaoyan Wang; Zhongqin Li; Edwards Ross; Ruozihan Tayier; Ping Zhou

    2015-02-01

    Many of the river basins in northwest China receive water from melting glaciers and snow in addition to groundwater. This region has experienced a significant change in glacier and snowpack volume over the past decade altering hydrology. Quantifying changes in water resources is vital for developing sustainable strategies in the region. During 2013, a water-isotope source apportionment study was conducted during the spring flood in the Yushugou River basin, northwestern China. The study found significant differences in water isotopes between river water, snowmelt water, and groundwater. During the study period, the isotopic composition of groundwater remained relatively stable. This stability suggests that the groundwater recharge rate has not been significantly impacted by recent hydro-climatic variability. The river water flow rate and water 18O displayed an inverse relationship. This relationship is indicative of snowmelt water injection. The relative contribution of the two sources was estimated using a two-component isotope hydrograph separation. The contribution of snowmelt water and groundwater to Yushugou River were ∼63% and ∼37%, respectively. From the study, we conclude that snowmelt water is the dominant water source to the basin during the spring melt period.

  11. Separating the contributions of vegetation and soil to evapotranspiration using stable isotopes

    Science.gov (United States)

    Cuntz, Matthias; Dubbert, Maren; Piayda, Arndt; Correia, Alexandra; Silva, Filipe Costa e.; Kolle, Olaf; Maguás, Cristina; Mosena, Alexander; Pereira, João S.; Rebmann, Corinna; Werner, Christiane

    2015-04-01

    Semi-arid ecosystems contribute about 40% to global net primary productivity, although water-availability limits carbon uptake. Precipitation shows periodical summer droughts and evapotranspiration accounts for up to 95% of water loss of the ecosystem. Thus functional understanding of evapotranspiration and the contributions of evaporation and transpiration from over- and understorey vegetation to water cycling in semi-arid regions is key knowledge in forest management under future climate change. Water isotopes trace water through the compartments of an ecosystem from soil and the vegetation to the atmosphere. They are used to partition evapotranspiration ET into its components evaporation E and transpiration T . The method is, however, sensitive to the knowledge of the isotopic composition of water at the evaporating sites. This led to a discussion recently about the dominance of transpiration in water loss from the terrestrial biosphere, and also how methodological problems could bias these results. Here we present observations from a Portuguese cork-oak woodland. It is a bi-layered system of widely spaced cork-oak trees and a herbaceous layer dominated by native annual forbs and grasses. Water fluxes and their isotopic compositions were measured on bare soil and vegetated plots with a transparent through-flow chamber and a water isotope laser. Soil moisture and temperature were measured in several depths and soil samples were taken for soil water isotope analysis. Based on these observations, we review current strategies of ET partitioning. We highlight pitfalls in the presented strategies and show uncertainty analyses for the different approaches. We show that the isotopic composition of evaporation is very sensitive to the sampling strategy but is described well by a steady-state formulation (Dubbert et al., J Hydrolo 2013). The isotopic composition of transpiration, on the other hand, is not in steady state, most of the time (Dubbert et al., New Phytolo 2014

  12. Rapid, high-purity chemical separation of molybdenum from iron meteorites for isotopic analysis by using thermal ionization mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Qi-Lu; Masuda, Akimasa (Tokyo Univ. (Japan). Dept. of Chemistry)

    1992-05-01

    A chemical procedure has been developed, which combines both solvent extraction and anion exchange, so that microgram amounts of Mo can be cleanly, rapidly and efficiently separated from gram amounts of iron meteorites. Particular attention was directed to the complete separation of Mo from Zr and Ru. The isotopic abundance ratios of Mo can subsequently be determined with high accuracy by using thermal ionization mass spectrometry. The experiments indicate that the behaviour of Mo during solvent extraction and anion exchange is considerably different from that reported previously. In particular, it was found that there is a very narrow range of HCl concentrations within which it is possible to separate Mo from Fe by solvent extraction. The reproducibility and recovery of the method were examined by using inductively coupled plasma atomic emission spectrometry. (Author).

  13. Formation cross-sections and chromatographic separation of protactinium isotopes formed in proton-irradiated thorium metal

    Energy Technology Data Exchange (ETDEWEB)

    Radchenko, Valery; Engle, Jonathan W.; Wilson, Justin J.; Maassen, Joel R.; Nortier, Meiring F.; Birnbaum, Eva R.; John, Kevin D.; Fassbender, Michael E. [Los Alamos National Laboratory, NM (United States)

    2016-08-01

    Targeted alpha therapy (TAT) is a treatment method of increasing interest to the clinical oncology community that utilizes α-emitting radionuclides conjugated to biomolecules for the selective killing of tumor cells. Proton irradiation of thorium generates a number of α-emitting radionuclides with therapeutic potential for application via TAT. In particular, the radionuclide {sup 230}Pa is formed via the {sup 232}Th(p, 3n) nuclear reaction and partially decays to {sup 230}U, an α emitter which has recently received attention as a possible therapy nuclide. In this study, we estimate production yields for {sup 230}Pa and other Pa isotopes from proton-irradiated thorium based on cross section measurements. We adopt existing methods for the chromatographic separation of protactinium isotopes from proton irradiated thorium matrices to combine and optimize them for effective fission product decontamination.

  14. Authenticity of aroma components Enantiomeric separation and compound specific stable isotope analysis

    DEFF Research Database (Denmark)

    Hansen, Anne-Mette Sølvbjerg

    using solid phase micro extraction with a polyacrylate fiber coating. The isotopic composition of the aroma extracted from vanilla custard powder, vanilla sugar, and cookies were determined and their authenticity evaluated accordingly. Extraction of vanilla aroma from ice cream was more complicated...... and a preliminary extraction was investigated. A liquid-liquid extraction was chosen in combination with solid phase micro extraction. With this method it was possible to analyze vanillin from 7 different ice creams and to evaluate their authenticity based on the measured carbon isotopic composition....

  15. Engineering Studies of a Pilot Plant for Laser Isotope Separation of CARBON-13 by Multiphoton Dissociation of Chlorodifluoromethane

    Science.gov (United States)

    Mehmetli, Bulent Ahmet

    Recent research in laser isotope separation by multiphoton dissociation (LISMPD) of ^{13 }C suggests that an LISMPD commercial process is more economical than the cryogenic CO distillation technology currently used to meet most of the world's ^ {13}C demand. In this dissertation, experimental studies of an engineering process for LISMPD of polyatomic molecules is examined. The experimental results have been obtained by MPD of chlorodifluoromethane (CF_2 HCl) to yield ^{13}C -enriched tetrafluoroethylene rm(C_2F _4). Emphasis is on research leading to the development of a practical chemical plant for the preparation of stable isotopes by this method. The experimental program has achieved the design, construction, and operation of a laboratory-scale ^{13}C separation apparatus and parametric dependences of enrichment factors and dissociated fractions. In this experiment, the reactant gas, industrial grade CF_2HCl, flows continuously along the axis of a stainless steel reaction cell. The beam of a commercial CO_2 TEA laser, delivering up to 3 J/pulse at a single wavelength, is focused into the cell to induce isotope-selective multiphoton dissociation. The ^{13}C-enriched reaction product, rm C_2F_4, is analyzed by mass spectroscopy for its isotopic content. Typical production rates of the setup are about 10 g/year ^{13}C at an enrichment of 15% or 1 g/year at an enrichment of 65%. The results of a detailed cost analysis, which takes into account different reaction conditions and laser types, showed that at production rates of 7,000 kg per year, the cost of ^{13}C can be as low as 4/g. This figure is about an order of magnitude less than the cost of ^13 C obtained by cryogenic distillation of CO. The design, construction, and operation of a CO _2 MOPA (Master Oscillator/ Power Amplifier) laser is proposed because a MOPA combines the advantages of favorable isotope separation reaction conditions of TEA lasers and the cheaper photons of cw discharges. Analytical

  16. Plasma centrifuge with vacuum arc discharge applied to the separation of stable isotopes

    Science.gov (United States)

    Delbosco, Edson

    1989-09-01

    The results of a vacuum-arc plasma centrifuge experiment are described. A plasma centrifuge is an apparatus where a plasma column is produced due to the interaction of an electric current with an externally applied magnetic field, vector J x vector B. Among the applications of a rotating plasma, this work deals particularly with its utilization in an isotope enrichment device. The main characteristics of the plasma produced in this experiment are presented, with special attention to the plasma column rotation and the isotope enrichment. The analysis of the results is performed using a fluid model for a completely ionized rigid body rotating plasma column in steady state equilibrium. The main results are: (1) rotation frequency of the plasma column in the range 2 x (exp 4) to 3 x 10 (exp 5) rad/s; (2) enrichment of 10 to 30 pct for the magnesium isotopes, and 290 to 490 pct for the carbon-13 isotope; (3) rigid body rotation of the plasma column only for radii smaller than the characteristic radius of the plasma column, r(sub e); (4) linear dependence of the rotation frequency upon the magnetic field strength only for r is less than r(sub e); (5) existence of an optimum value of the magnetic field for maximum enrichment; and (6) dependence of the rotation frequency upon the inverse of the atomic mass.

  17. Environmental impact statements: Nuclear industry waste disposal and isotope separation projects. (Latest citations from the NTIS bibliographic database). Published Search

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    The bibliography contains citations concerning draft and final impact statements relating to environmental radiation hazards. Prepared by the Department of Energy (DOE), Nuclear Regulatory Commission, Oak Ridge National Laboratory, and others, these reports discuss environmental data affecting DOE decisions on proposed construction and decommissioning of nuclear power plants, radioactive waste disposal facilities and sites, and isotope separation projects. The effects of Federal guidelines and atomic facility location on community awareness are examined. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  18. Formation of residual nuclei with medium mass number in the reaction of protons with separated tin isotopes

    CERN Document Server

    Aleksandryan, V E; Balabekyan, A R; Danagulyan, A S; Kalinnikov, V G; Musulmanbekov, G; Rodionov, V K; Stegailov, V I; Frana, J

    2000-01-01

    The mechanism of formation of residual nuclei in the mass region 42<=A<=81 in the reactions of protons with separated tin isotopes at three protons energies 0.66, 1.0 and 8.1 GeV was investigated. The absolute cross-sections of the residual nuclei were compared with the theoretical ones calculated by the standard cascade-evaporation and the intranuclear cascad plus statistical multifragmentation models (INC+SMM). It was shown that at E sub p =8.1 GeV these nuclei may arise both from disintegration of the nucleus and as partners of several fragments.

  19. Golan Heights Groundwater Systems: Separation By REE+Y And Stable Isotopes

    Science.gov (United States)

    Siebert, C.; Geyer, S.; Knoeller, K.; Roediger, T.; Weise, S.; Dulski, P.; Moeller, P.; Guttman, J.

    2008-12-01

    In a semi-arid to arid country like Israel, all freshwater resources are under (over-) utilization. Particularly, the Golan Heights rank as one of the most important extraction areas of groundwater of good quality and quantity. Additionally the mountain range feed to a high degree the most important freshwater reservoir of Israel, the Sea of Galilee. Hence, knowing the sources and characters of the Golan Heights groundwater systems is an instantaneous demand regarding sustainable management and protection. Within the "German-Israeli-Jordanian-Palestinian Joint Research Program for the Sustainable Utilisation of Aquifer Systems", hundreds of water samples were taken from all over the Jordan-Dead Sea rift-system to understand groundwater flow-systems and salinisation. For that purpose, each sample was analysed for major and minor ions, rare earth elements including yttrium (REY) and stable isotopes of water (d18O, d2H). The REY distribution in groundwater is established during infiltration by the first water-rock interaction and consequently reflects the leachable components of sediments and rocks of the recharge area. In well- developed flow-systems, REY are adsorbed onto pore surfaces are in equilibrium with the percolating groundwater, even if the lithology changes (e.g. inter-aquifer flow). Thus, groundwater sampled from wells and springs still show the REY distribution pattern established in the recharge area. Since high temperatures do not occur in Golan Heights, d2H and d18O are less controlled by water-rock interaction than by climatic and geomorphological factors at the time of replenishment. Applying the REY signature as a grouping criterion of groundwaters, d18O vs. d2H plots yield a new dimension in interpreting isotope data. The combined use of hydrochemical and isotopic methods enabled us to contain the areas of replenishment and the flow-paths of all investigated groundwater in the Golan Heights. Despite location, salinity or temperature of spring or

  20. Preliminary results on the determination of ultratrace amounts of cadmium in tea samples using a flow injection on-line solid phase extraction separation and preconcentration technique to couple with a sequential injection hydride generation atomic fluorescence spectrometry.

    Science.gov (United States)

    Duan, Taicheng; Song, Xuejie; Jin, Dan; Li, Hongfei; Xu, Jingwei; Chen, Hangting

    2005-10-31

    In this work, a method was developed for determination of ultra-trace levels of Cd in tea samples by atomic fluorescence spectrometry (AFS). A flow injection solid phase extraction (FI-SPE) separation and preconcentration technique, to on-line couple with a sequential injection hydride generation (SI-HG) technique is employed in this study. Cd was preconcentrated on the SPE column, which was made from a neutral extractant named Cyanex 923, while other matrix ions or interfering ions were completely or mostly separated off. Conditions for the SPE separation and preconcentration, as well as conditions for the HG technique, were studied. Due to the separation of interfering elements, Cd hydride generation efficiency could be greatly enhanced with the sole presence of Co(2+) with a concentration of 200mugL(-1), which is much lower than those in other works previously reported. Interferences on both the Cd separation and preconcentration, and Cd hydride generation (HG) were investigated; it showed that both the separation and preconcentration system, and the HG system had a strong anti-interference ability. The SPE column could be repeatedly used at least 400 times, a R.S.D. of 0.97% was obtained for 6 measurements of Cd with 0.2mugL(-1) and a correlation coefficiency of 1.0000 was obtained for the measurement of a series of solutions with Cd concentrations from 0.1 to 2mugL(-1). The method has a low detection limit of 10.8ngL(-1) for a 25mL solution and was successfully validated by using two tea standard reference materials (GBW08513 and GBW07605).

  1. Isotope-Dilution Mass Spectrometry for Quantification of Urinary Active Androgens Separated by Gas Chromatography

    OpenAIRE

    Su Hyeon Lee; Man Ho Choi; Won-Yong Lee; Bong Chul Chung

    2010-01-01

    Cross reacting antibodies can cause an overestimation of the results of immunoassays. Therefore, alternative methodsare needed for the accurate quantification of steroids. Gas chromatography combined with isotope-dilution mass spectrometry(GC-IDMS) is developed to quantify urinary active androgens, testosterone, epitestosterone and dihydrotestosterone, which areclinically relevant androgens to both hair-loss and prostate diseases. The method devised involves enzymatic hydrolysis with β-glucur...

  2. Stable isotope analysis of diet confirms niche separation of two sympatric species of Namib Desert lizard.

    Science.gov (United States)

    Murray, Ian W; Lease, Hilary M; Hetem, Robyn S; Mitchell, Duncan; Fuller, Andrea; Woodborne, Stephan

    2016-01-01

    We used stable isotopes of carbon and nitrogen to study the trophic niche of two species of insectivorous lizards, the Husab sand lizard Pedioplanis husabensis and Bradfield's Namib day gecko living sympatrically in the Namib Desert. We measured the δ(13) C and δ(15) N ratios in lizard blood tissues with different turnover times (whole blood, red blood cells and plasma) to investigate lizard diet in different seasons. We also measured the δ(13) C and δ(15) N ratios in available arthropod prey and plant tissues on the site, to identify the avenues of nutrient movement between lizards and their prey. Through the use of stable isotope mixing models, we found that the two lizard species relied on a largely non-overlapping but seasonally variable array of arthropods: P. husabensis primarily fed on termites, beetles and wasps, while R. bradfieldi fed mainly on ants, wasps and hemipterans. Nutrients originating from C3 plants were proportionally higher for R. bradfieldi than for P. husabensis during autumn and late autumn/early winter, although not summer. Contrary to the few available data estimating the trophic transfer of nutrients in ectotherms in mixed C3 and C4 /crassulacean acid metabolism (CAM) plant landscapes, we found that our lizard species primarily acquired nutrients that originated from C4 /CAM plants. This work adds an important dimension to the general lack of studies using stable isotope analyses to estimate lizard niche partitioning and resource use.

  3. 62Ni 同位素的分离制备%Separation and Preparation of 62 Ni Isotope

    Institute of Scientific and Technical Information of China (English)

    任秀艳; 米亚静; 曾自强; 李公亮; 屠锐

    2014-01-01

    微型核电池是目前航天器仪器、设备理想的电源。63 Ni是镍电池的核心工作物质。通过在反应堆中辐照高丰度的稳定同位素62 Ni ,能产生放射性同位素63 Ni。为保证62 Ni的丰度达到要求,本文开展了62 Ni同位素的分离制备研究,进行了磁场及束流输运计算,对离子源及接收器口袋进行了改进设计,制定了电磁分离法分离高丰度62 Ni的工艺流程。利用现有的电磁同位素分离器,开展了用电磁分离法分离高丰度、高纯度62 Ni稳定同位素的实验,最终获得了丰度≥90%的62 Ni同位素。%Micro nuclear battery is the perfect power of space craft equipment .63 Ni is the core operation material of the 63 Ni battery .It can produce radioisotope 63 Ni w hile high abundance 62 Ni is irradiated in the reactor .In order to meet the requirements of the abundance and the purity ,research of the separation for 62 Ni isotope was developed . The magnetic field and beam transmission status were simulated . The improvement designs of the ion source and the collector pocket were carried out .The process flow of high abundance 62 Ni using electromagnetic separation method was established . The experiment of 62 Ni isotope was developed by using electromagnetism isotope separator . The results show that the enrichment of 62 Ni isotope is more than 90% .

  4. Automated on-line column-switching high performance liquid chromatography isotope dilution tandem mass spectrometry method for the quantification of bisphenol A, bisphenol F, bisphenol S, and 11 other phenols in urine.

    Science.gov (United States)

    Zhou, Xiaoliu; Kramer, Joshua P; Calafat, Antonia M; Ye, Xiaoyun

    2014-01-01

    Human exposure to bisphenol A (BPA) is widespread. However, in recent years, bisphenol analogs such as bisphenol S (BPS) and bisphenol F (BPF) are replacing BPA in the production of some consumer products. Because human exposure to these alternative bisphenols may occur, biomonitoring of these bisphenol analogs is warranted. In the present study, we developed and validated a sensitive and selective method that uses on-line solid phase extraction coupled to high performance liquid chromatography-isotope dilution tandem mass spectrometry with peak focusing to measure BPA, BPF, BPS, and 11 other environmental phenols in urine. The method required a small amount of sample (100μL) and minimal sample pretreatment. The limits of detection were 0.03ng/mL (BPS), 0.06ng/mL (BPF), 0.10ng/mL (BPA), and ranged from 0.1ng/mL to 1.0ng/mL for the other 11 phenols. In 100 urine samples collected in 2009-2012 from a convenience group of anonymous adults in the United States, of the three bisphenols, we detected BPA at the highest frequency and median concentrations (95%, 0.72ng/mL), followed by BPS (78%, 0.13ng/mL) and BPF (55%, 0.08ng/mL). This sensitive, rugged, and labor and cost-effective method could be used for the analysis of large number of samples for epidemiologic studies.

  5. 适用于时变系统的在线盲源分离算法研究%Research on on-line blind source separation algorithm for time-vary-ing system

    Institute of Scientific and Technical Information of China (English)

    邓大鹏; 李骏; 丁德强; 贺翥祯

    2016-01-01

    针对传统EASI算法收敛速率与稳态误差之间的矛盾,提出了一种基于估计函数期望的步长自适应算法(New Adaptive EASI),为了使这种算法能够更好地解决时变系统中不同条件下的盲源分离问题,提高信号的分离精度,建立了一种混合矩阵变化的在线检测机制,并将这种在线检测机制加入步长自适应算法中,对算法进行了改进.仿真实验表明,这种改进的步长自适应算法能够提高盲源分离初始阶段或是信道变化后分离初始阶段的信号恢复质量,解决源信号为非零均值信号时的盲源分离问题,并且能够准确地在线估计源信号的个数,实现信源数变化条件下的盲源分离.%Aiming at the contradiction between the convergence rate and the steady-state error of the traditional EASI algorithm, this paper presents a New Adaptive EASI algorithm based on the expectation of estimate function. In order to make the new algorithm be able to solve the BSS problems under different conditions of time-varying system better and improve the accuracy of separated signals, it sets up an on-line detection mechanism of the changes in mixing matrix and adds it to the New Adaptive EASI algorithm to modify the algorithm. Simulation results show that the modified New Adaptive EASI algorithm can improve the quality of separated signals in the initial stage of separation or just after the channel condition changes, do the on-line separation of nonzero mean mixed signals and accurately estimate the number of source signals online to solve the BSS problem under the condition that the number of the source signals varies during the separating process.

  6. Uncertainty Quantification of Multi-Component Isotope-Separation Cascade Model

    Science.gov (United States)

    2010-03-01

    School of Engineering and Management Air Force Institute of Technology Air University Air Education and Training Command In Partial Fulfillment of the...of Stages with Large Separation Factors”. Presented at the Workshop on Separation Phenomena in Liquids and Gases, Technische Hochschule, Darmstadt

  7. Membrane pumping technology for helium and hydrogen isotope separation in the fusion reactor

    Energy Technology Data Exchange (ETDEWEB)

    Pistunovich, V.I. [Kurchatov Inst., Moscow (Russian Federation). NFI RRC; Pigarov, A.Yu. [Kurchatov Inst., Moscow (Russian Federation). NFI RRC; Busnyuk, A.O. [Bonch-Bruyevich University, St. Petersburg (Russian Federation); Livshits, A.I. [Bonch-Bruyevich University, St. Petersburg (Russian Federation); Notkin, M.E. [Bonch-Bruyevich University, St. Petersburg (Russian Federation); Samartsev, A.A. [Bonch-Bruyevich University, St. Petersburg (Russian Federation); Borisenko, K.L. [Efremov Institute, St. Petersburg (Russian Federation); Darmogray, V.V. [Efremov Institute, St. Petersburg (Russian Federation); Ershov, B.D. [Efremov Institute, St. Petersburg (Russian Federation); Filippova, L.V. [Efremov Institute, St. Petersburg (Russian Federation); Mudugin, B.G. [Efremov Institute, St. Petersburg (Russian Federation); Odintsov, V.N. [Efremov Institute, St. Petersburg (Russian Federation); Saksagansky, G.L. [Efremov Institute, St. Petersburg (Russian Federation); Serebrennikov, D.V. [Efremov Institute, St. Petersburg (Russian Federation)

    1995-03-01

    A gas pumping system for ITER, improved by implementation of superpermeable membranes for selective hydrogen isotope exhaust, is considered. A study of the pumping capability of a niobium membrane for a hydrogen-helium mixture has been performed.Monte Carlo simulations of gas behaviour for the experimental facility and fusion reactor have been done.The scheme of the ITER pumping system with the membranes and membrane pumping technology was considered. The conceptual study the membrane pump for the ITER was done. This work gives good prospects for the membrane pumping use in ITER to reduce the total inventory of tritium necessary for reactor operation. (orig.).

  8. Stable isotope signatures reveal small-scale spatial separation in populations of European sea bass

    OpenAIRE

    Cambiè, Giulia; Kaiser, Michel J.; Marriott, Andrew L.; Fox, Jennifer; Lambert, Gwladys; Hiddink, Jan G.; Overy, Thomas; Bennett, Sarah A.; Leng, Melanie J.; McCarthy, Ian D

    2016-01-01

    Scientific information about European sea bass Dicentrarchus labrax stocks in the NE Atlantic is limited and a more accurate definition of the stock boundaries in the area is required to improve assessment and management advice. We investigated the connectivity and movement patterns of D. labrax in Wales (UK) using the stable isotope (δ13C and δ15N) composition of their scales. Analysis of δ13C and δ15N values in the last growing season was performed on 189 adult sea bass caught at 9 coastal ...

  9. Preparation and characterization of hydrophobic platinum-doped carbon aerogel catalyst for hydrogen isotope separation

    Indian Academy of Sciences (India)

    M K Singh; R Singh; A Singh; D K Kohli; U Deshpande; P K Gupta

    2014-10-01

    We report preparation of hydrophobic platinum-doped carbon aerogel (PtCA) catalyst and its characterization for catalytic exchange reactions between hydrogen isotopes. The PtCA powder was synthesized by sol–gel polymerization method, mixed with colloidal PTFE solution, and coated on Dixon rings to obtain hydrophobic catalyst. The Pt cluster size in PtCA powder was observed to vary from 3 to 5 nm for a change in resorcinol to alkali molar ratio in synthesis solution from 20 to 200. Transmission electron microscopy of powder showed that the Pt clusters were uniformally dispersed and Pt0 metallic content estimated by X-ray photoelectron spectroscopy (XPS) was found to be of ∼ 70%. The catalytic activity was found to depend on Pt cluster size and was higher for smaller cluster size. For the smallest achieved Pt cluster size of 3 nm, catalytic activity of ∼ 0.8 m3 (STP) s-1 m-3 was obtained for hydrogen isotope exchange in atmospheric pressure conditions.

  10. Membrane pumping technology, helium and hydrogen isotopes separation in the fusion hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Pigarov, A.Yu.; Pistunovich, V.I. [NFI RRC-Kurchatov Institute, Moscow (Russian Federation); Busnyuk, A.O. [Bonch-Bruyevich Electrotechnical Inst. of Communications, St. Petersburg (Russian Federation)] [and others

    1994-12-31

    A gas pumping system for the ITER, improved by implementation of superpermeable membranes for selective hydrogen isotope exhaust, is considered. The study of the pumping capability of a niobium membrane for a hydrogen-helium mixture has been fulfilled. The membrane superpermeability can be only realized for atomic hydrogen. Helium does not pass through the membrane, and its presence does not affect the hydrogen pumping. A detailed Monte Carlo simulation of gas behavior for the experimental facility has been done. The probability of permeation for a hydrogen atom for one collision with the membrane is {approximately}0.1; the same probability of molecule permeation is {approximately}10{sup {minus}5}. The probability for atomization, i.e. re-emission of an atomizer is {approximately}0.2; the probability of recombination of an atom is {approximately}0.2.

  11. Penning-trap Q-value determination of the {sup 71}Ga(ν,e{sup −}){sup 71}Ge reaction using threshold charge breeding of on-line produced isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Frekers, D., E-mail: Frekers@Uni-Muenster.de [Institut für Kernphysik, Westfälische Wilhelms-Universität, 48149 Münster (Germany); Simon, M.C. [TRIUMF, Vancouver, BC V6T 2A3 (Canada); Andreoiu, C. [Department of Chemistry, Simon Fraser University, Burnaby, BC V5A 1S6 (Canada); Bale, J.C. [TRIUMF, Vancouver, BC V6T 2A3 (Canada); Department of Chemistry, Simon Fraser University, Burnaby, BC V5A 1S6 (Canada); Brodeur, M. [NSCL, Michigan State University, East Lansing, MI 48824 (United States); Brunner, T. [TRIUMF, Vancouver, BC V6T 2A3 (Canada); Physik Department E12, Technische Universität München, 85748 Garching (Germany); Chaudhuri, A. [TRIUMF, Vancouver, BC V6T 2A3 (Canada); Chowdhury, U. [TRIUMF, Vancouver, BC V6T 2A3 (Canada); Department of Physics, University of Manitoba, Winnipeg, MB R3T 2N2 (Canada); Crespo López-Urrutia, J.R. [Max Planck Institute for Nuclear Physics, 69117 Heidelberg (Germany); Delheij, P. [TRIUMF, Vancouver, BC V6T 2A3 (Canada); Ejiri, H. [Research Center for Nuclear Physics, Osaka University, Ibaraki, Osaka 560-0047 (Japan); Ettenauer, S.; Gallant, A.T. [TRIUMF, Vancouver, BC V6T 2A3 (Canada); Department of Physics and Astronomy, University of British Columbia, Vancouver, BC V6T 1Z1 (Canada); Gavrin, V. [Institute for Nuclear Research, Russian Academy of Sciences, Moscow, 1173122 (Russian Federation); Grossheim, A. [TRIUMF, Vancouver, BC V6T 2A3 (Canada); Harakeh, M.N. [Kernfysisch Versneller Instituut, University of Groningen, NL-9747 AA Groningen (Netherlands); Jang, F. [Department of Physics and Astronomy, University of British Columbia, Vancouver, BC V6T 1Z1 (Canada); Kwiatkowski, A.A. [TRIUMF, Vancouver, BC V6T 2A3 (Canada); and others

    2013-05-24

    We present a first direct Q-value measurement of the {sup 71}Ga(ν,e{sup −}){sup 71}Ge reaction using the TITAN mass-measurement facility at ISAC/TRIUMF. The measurements were performed in a Penning trap on neon-like {sup 71}Ga{sup 21+} and {sup 71}Ge{sup 22+} using isobar separation of the on-line produced mother and daughter nuclei through threshold charge breeding in an electron-beam ion trap. In addition, isoionic samples of {sup 71}Ga{sup 21+} and {sup 71}Ge{sup 21+} were stored concurrently in the Penning trap and provided a separate Q-value measurement. Both independent measurements result in a combined Q-value of 233.5±1.2 keV, which is in agreement with the previously accepted Q-value for the ν cross-section calculations. Together with a recent measurement of the ν-response from the excited states in {sup 71}Ge, we conclude that there are no further uncertainties in the nuclear structure, which could remove the persistent discrepancy between the SAGE and GALLEX calibration measurements performed with neutrinos from reactor-produced {sup 51}Cr and {sup 37}Ar sources and the theoretical expectation.

  12. Runoff separation and eco-hydrological function in the typical landscape zones combining hydrochemical and isotopic tracers:a review

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The study on the coupling relationship and hydrology mechanism between ecosystem and hydrological process in a basin has recently become the international research frontier in hydrology.Runoff separation is still an important subject and possibly cutting edge process in hydrology.This paper summarizes the progress of national and international research,and comments on the advantages and disadvantages of recent,diverse base flow separation methods.This paper also presents research on hydrological process and eco-hydrological function in different landscape zones,combining isotopic technology with hydrochemical methods.Based on the runoff separation of different water bodies,this paper probes into the coupling relationship and hydrology mechanism between ecosystem pattern and eco-hydrological process,and makes analysis on water conservation,regulation and storage mechanism,and eco-hydrological function in different landscape zones.This report also examines future trends in research on hydrological process and eco-hydrological function in mountainous areas.

  13. Boundary-value problem for a counterrotating electrical discharge in an axial magnetic field. [plasma centrifuge for isotope separation

    Science.gov (United States)

    Hong, S. H.; Wilhelm, H. E.

    1978-01-01

    An electrical discharge between two ring electrodes embedded in the mantle of a cylindrical chamber is considered, in which the plasma in the anode and cathode regions rotates in opposite directions under the influence of an external axial magnetic field. The associated boundary-value problem for the coupled partial differential equations describing the azimuthal velocity and radial current-density fields is solved in closed form. The velocity, current density, induced magnetic induction, and electric fields are presented for typical Hartmann numbers, magnetic Reynolds numbers, and geometry parameters. The discharge is shown to produce anodic and cathodic plasma sections rotating at speeds of the order 1,000,000 cm/sec for conventional magnetic field intensities. Possible application of the magnetoactive discharge as a plasma centrifuge for isotope separation is discussed.

  14. Coupling Optimization Design and Experimental Study on Stable Isotope 13C Separation of the Double-stage Cascade

    Directory of Open Access Journals (Sweden)

    TIAN Ye-sheng;LI Hu-lin;JIANG Yong-yue;LONG Lei;JI Yong-zhe;ZHOU Jian-yue

    2016-08-01

    Full Text Available A coupling optimization design and experimental study method with uniform experimental and Aspen process simulation was established in this paper, which was used for stable isotope 13C separation of the double-stage cascade. Based on the above method, the optimization operating parameters were received. The coupling optimization simulation value showed good agreement with the experimental dates, and the average relative error was only 6.5%. On the other hand, compared with the initial test result, the 13C abundance of optimized experimental was 14.1%, and the actual growth rate of 13C abundance was more than 25%. More importantly, The optimization experimental did not increase energy consumption. The method confirmed by the experiment could provide a solid foundation for the cascade process of 13C industrialization, and it could also be applied to other traditional distillation industry.

  15. Software development for the simulation and design of the cryogenic distillation cascade used for hydrogen isotope separation

    Energy Technology Data Exchange (ETDEWEB)

    Draghia, Mirela Mihaela, E-mail: mirela.draghia@istech-ro.com; Pasca, Gheorghe; Porcariu, Florina

    2016-11-01

    Highlights: • Software for designing and simulation of a cryogenic distillation cascade. • The simulation provides the distribution of all the molecular species involved along each cryogenic distillation column and also the temperature profile along the columns. • Useful information that are relevant for ITER Isotope Separation System. - Abstract: The hydrogen isotope separation system (ISS) based on cryogenic distillation is one of the key systems of the fuel cycle of a fusion reactor. Similar with ITER ISS in a Water Detritiation Facility for a CANDU reactor, one of the main systems is cryogenic distillation. The developments on the CANDU water detritiation systems have shown that a cascade of four cryogenic distillation columns is required in order to achieve the required decontamination factor of the heavy water and a tritium enrichment up to 99.9%. This paper aims to present the results of the design and simulation activities in support to the development of the Cernavoda Tritium Removal Facility (CTRF). Beside the main features of software developed “in house”, an introduction to the main relevant issues of a CANDU tritium removal facility for the ITER ISS is provided as well. Based on the input data (e.g. the flow rates, the composition of the gas supplied into the cryogenic distillation cascade, pressure drop along the column, liquid inventory) the simulation provides the distribution of all the molecular species involved along each cryogenic distillation column and also the temperature profile along the columns. The approach for the static and dynamic simulation of a cryogenic distillation process is based on theoretical plates model and the calculations are performed incrementally plate by plate.

  16. Baseflow separation in a premontane transitional rainforest using stable isotope techniques

    Science.gov (United States)

    Miller, G. R.; DuMont, A.; Roark, E.; Cahill, A. T.; Brumbelow, J. K.

    2013-12-01

    Hydrologic, geologic, and biologic processes are critical to understanding the ecosystem in the tropical premontane transitional forests of Costa Rica. Precipitation is significantly lower during the dry season, and incoming rainfall can be completely intercepted and re-evaporated by the canopy during light events. These canopy processes can affect the rates of runoff and infiltration by changing the quantity and timing of rainfall reaching the ground surface. However, the resulting partitioning of stream water sources between event-water and baseflow from groundwater is not well quantified due to limited accessibility and complex subsurface conditions. This study focuses on research conducted at the Texas A&M Soltis Center for Education and Research, near San Ramón, Costa Rica. We have monitored a 2.2 ha watershed there, measuring precipitation and transpiration rates for over two years, and groundwater levels and stream flow rates for nearly one year. Precipitation rates for the watershed averaged 4.4 m/yr since 2010. Stream flow (runoff, spring flow, and baseflow) averaged 0.09 m^3/sec during the 2012-2013 wet seasons. At 1.2 mm/day, transpiration was a relatively minor component of the water budget. Over a 40-day span during summer 2013, we collected a combination of daily and rain-event based samples from locations throughout the watershed. Sources included: the main stream and two small tributaries, groundwater from piezometers, pore water from suction lysimeters, throughfall and stemflow from under canopy collection systems, and xylem water from 8 tree species across the watershed. We then measured stable isotope fractions (δ18O and δD) in the water using a Picarro L2120i CRDS. Isotope ratios for all surface water averaged -5.50‰ for δ18O and -28.00‰ for δD, while that measured under baseflow conditions were -5.45‰ for δ18O and -29.18‰ for δD. These results indicate that baseflow is the dominate source of stream water even in the wet season

  17. Separation of drainage runoff during rainfall-runoff episodes using the stable isotope method and drainage water temperature

    Science.gov (United States)

    Zajíček, Antonín; Kvítek, Tomáš; Pomije, Tomáš

    2014-05-01

    Stabile isotopes of 2H 18O and drainage water temperature were used as natural tracers for separation rainfall-runoff event hydrograph on several tile drained catchments located in Bohemian-Moravian Highland, Czech Republic. Small agricultural catchments with drainage systems built in slopes are typical for foothill areas in the Czech and Moravian highland. Often without permanent surface runoff, the drainage systems represent an important portion of runoff and nitrogen leaching out of the catchment. The knowledge of the drainage runoff formation and the origin of its components are prerequisites for formulation of measures leading to improvement of the drainage water quality and reduction of nutrient leaching from the drained catchments. The results have proved presence of event water in the drainage runoff during rainfall-runoff events. The proportion of event water observed in the drainage runoff varied between 15 - 60 % in the summer events and 0 - 50 % in winter events, while the sudden water temperature change was between 0,1 - 4,2 °C (2 - 35 %). The comparison of isotope separation of the drainage runoff and monitoring the drainage water temperature have demonstrated that in all cases of event water detected in the runoff, a rapid change in the drainage water temperature was observed as well. The portion of event water in the runoff grows with the growing change in water temperature. Using component mixing model, it was demonstrated that water temperature can be successfully used at least as a qualitative and with some degree of inaccuracy as a quantitative tracer as well. The drawback of the non-conservative character of this tracer is compensated by both its economic and technical accessibility. The separation results also resemble results of separations at small streams. Together with a similarly high speed of the discharge reaction to beginning of precipitation, it is obvious that the mechanism of surface runoff formation and drainage runoff formation

  18. Measurement of isotope separation factors in the palladium-hydrogen system using a thermistor technique

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz, T.M.

    1998-05-01

    The range of available data on separation factors in the palladium-hydrogen/deuterium system has been extended. A matched pair of glass-coated bead thermistors was used to measure gas phase compositions. The compositions of the input gas--assumed also to be the solid phase composition--were measured independently be mass spectrometry as being within 0.5 mole% of the values used to calibrate the thermistors. This assumption is based on the fact that > 99% of the input gas is absorbed into the solid. Separation factors were measured for 175 K {le} T {le} 389 K and for 0.195 {le} x{sub H} {le} 0.785.

  19. A gas chromatograph/mass spectrometry method for determining isotopic distributions in organic compounds used in the chemical approach to stable isotope separation

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, A.M.; Spall, W.D.; Smith, B.F.

    1990-01-01

    A variety of gas chromatograph/mass spectrometry (GC/MS) methods have been developed to resolve benzene, benzophenone, anthracene, fluorenone, and their respective stable isotope analogs from other components by gas chromatography. The ratio of stable isotope-labeled material to natural isotopic abundance compounds is determined from the mass spectra averaged across the chromatographic peak. Both total ion and selective ion chromatographic approaches were used for relative data and comparison. 9 refs., 11 tabs.

  20. The investigation of properties of short-lived SF isotopes (Z > 100 at the focal plane of VASSILISSA separator

    Directory of Open Access Journals (Sweden)

    Svirikhin Alexandr

    2013-12-01

    Full Text Available For experiments aimed at the study of spontaneous fission of transfermium nuclei improvements in the focal plane detector system of recoil separator VASSILISSA have been made. A neutron detector consisting of 54 3He-filled counters has been mounted around the focal-plane detector chamber. The reaction 48Ca + 206Pb = 2n + 252No is used for tuning the separator settings and calibrating the detector system with the spontaneous fission of the 252No. The average neutron number per 252No spontaneous fission event is as large as ν̅ = 4.06 ± 0.12. The short-lived heavy isotopes 244,246Fm, produced in the complete fusion reactions 40Ar + 206,208Pb, are investigated. The average number of neutrons per spontaneous fission of 244,246Fm from the experimental data were (ν̅ = 3.3 ± 0.3 and (ν̅ = 3.55 ± 0.50, respectively. Both values are determined for the first time.

  1. Two-step laser ionization schemes for in-gas laser ionization and spectroscopy of radioactive isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Kudryavtsev, Yu., E-mail: yuri.kudryavtsev@fys.kuleuven.be; Ferrer, R.; Huyse, M.; Van den Bergh, P.; Van Duppen, P. [Instituut voor Kern- en Stralingsfysica, KU Leuven, 3001 Leuven (Belgium); Vermeeren, L. [SCK-CEN, Nuclear Research Centre, Boeretang 200, B-2400 Mol (Belgium)

    2014-02-15

    The in-gas laser ionization and spectroscopy technique has been developed at the Leuven isotope separator on-line facility for the production and in-source laser spectroscopy studies of short-lived radioactive isotopes. In this article, results from a study to identify efficient optical schemes for the two-step resonance laser ionization of 18 elements are presented.

  2. Pygmy dipole strength close to particle-separation energies - the case of the Mo isotopes

    CERN Document Server

    Rusev, G; Erhard, M; Junghans, A; Kosev, K; Schilling, K D; Schwengner, R; Wagner, A; Rusev, Gencho; Grosse, Eckart; Erhard, Martin; Junghans, Arnd; Kosev, Krasimir; Schilling, Klaus-Dieter; Schwengner, Ronald; Wagner, Andreas

    2005-01-01

    The distribution of electromagnetic dipole strength in 92, 98, 100 Mo has been investigated by photon scattering using bremsstrahlung from the new ELBE facility. The experimental data for well separated nuclear resonances indicate a transition from a regular to a chaotic behaviour above 4 MeV of excitation energy. As the strength distributions follow a Porter-Thomas distribution much of the dipole strength is found in weak and in unresolved resonances appearing as fluctuating cross section. An analysis of this quasi-continuum - here applied to nuclear resonance fluorescence in a novel way - delivers dipole strength functions, which are combining smoothly to those obtained from (g,n)-data. Enhancements at 6.5 MeV and at ~9 MeV are linked to the pygmy dipole resonances postulated to occur in heavy nuclei.

  3. New sequential separation procedure for Sr, Nd and Pb isotope ratio measurement in geological material using MC-ICP-MS and TIMS

    Digital Repository Service at National Institute of Oceanography (India)

    Makishima, A.; Nath, B.N.; Nakamura, E.

    A new 3-step sequential separation chemistry for Sr, Nd and Pb from silicate samples, which is suitable for isotope analysis by MC-ICP-MS as well as TIMS, has been developed. The chemistry is designed to minimize the number of evaporation steps...

  4. Proceedings of the XVIIth International Conference on Electromagnetic Isotope Separators and Related Topics (EMIS2015), Grand Rapids, MI, U.S.A., 11-15 May 2015

    Science.gov (United States)

    Bollen, Georg; Mittig, Wolfgang; Morrissey, Dave; Schwarz, Stefan; Villari, Antonio

    2016-06-01

    The 17th International Conference on Electromagnetic Isotope Separators and Related Topics (EMIS-2015) was held in Grand Rapids, Michigan, in the United States, from May 11th to 15th, 2015. The EMIS-2015 conference was hosted by Michigan State University. The present volume contains the proceedings of the event.

  5. Long-term fertilization alters chemically-separated soil organic carbon pools: Based on stable C isotope analyses

    Science.gov (United States)

    Dou, Xiaolin; He, Ping; Cheng, Xiaoli; Zhou, Wei

    2016-01-01

    Quantification of dynamics of soil organic carbon (SOC) pools under the influence of long-term fertilization is essential for predicting carbon (C) sequestration. We combined soil chemical fractionation with stable C isotope analyses to investigate the C dynamics of the various SOC pools after 25 years of fertilization. Five types of soil samples (0–20, 20–40 cm) including the initial level (CK) and four fertilization treatments (inorganic nitrogen fertilizer, IN; balanced inorganic fertilizer, NPK; inorganic fertilizer plus farmyard manure, MNPK; inorganic fertilizer plus corn straw residue, SNPK) were separated into recalcitrant and labile fractions, and the fractions were analysed for C content, C:N ratios, δ13C values, soil C and N recalcitrance indexes (RIC and RIN). Chemical fractionation showed long-term MNPK fertilization strongly increased the SOC storage in both soil layers (0–20 cm = 1492.4 gC m2 and 20–40 cm = 1770.6 gC m2) because of enhanced recalcitrant C (RC) and labile C (LC). The 25 years of inorganic fertilizer treatment did not increase the SOC storage mainly because of the offsetting effects of enhanced RC and decreased LC, whereas no clear SOC increases under the SNPK fertilization resulted from the fast decay rates of soil C.

  6. Long-term fertilization alters chemically-separated soil organic carbon pools: Based on stable C isotope analyses.

    Science.gov (United States)

    Dou, Xiaolin; He, Ping; Cheng, Xiaoli; Zhou, Wei

    2016-01-01

    Quantification of dynamics of soil organic carbon (SOC) pools under the influence of long-term fertilization is essential for predicting carbon (C) sequestration. We combined soil chemical fractionation with stable C isotope analyses to investigate the C dynamics of the various SOC pools after 25 years of fertilization. Five types of soil samples (0-20, 20-40 cm) including the initial level (CK) and four fertilization treatments (inorganic nitrogen fertilizer, IN; balanced inorganic fertilizer, NPK; inorganic fertilizer plus farmyard manure, MNPK; inorganic fertilizer plus corn straw residue, SNPK) were separated into recalcitrant and labile fractions, and the fractions were analysed for C content, C:N ratios, δ(13)C values, soil C and N recalcitrance indexes (RIC and RIN). Chemical fractionation showed long-term MNPK fertilization strongly increased the SOC storage in both soil layers (0-20 cm = 1492.4 gC m(2) and 20-40 cm = 1770.6 gC m(2)) because of enhanced recalcitrant C (RC) and labile C (LC). The 25 years of inorganic fertilizer treatment did not increase the SOC storage mainly because of the offsetting effects of enhanced RC and decreased LC, whereas no clear SOC increases under the SNPK fertilization resulted from the fast decay rates of soil C.

  7. 冠状化合物在锂同位素分离中的应用%Application of Crown Compounds in Lithium Isotopes Separation

    Institute of Scientific and Technical Information of China (English)

    束玉珍; 吴继宗; 邓惟勤

    2015-01-01

    Lithium is composed of two stable isotopes that both have important application in the nuclear power industry.The industrial method for lithium isotope separation is with amalgam,but huge volumes of toxic mercury used in this method bring about serious health and environmental problems.Thus,it is imperative to look for a green and effective method for lithium isotope separation.Since the crown ether was synthesized,it has become a research focus for its excellent properties on lithium isotope separation.In this paper,to provide a reference for the further research,nearly 40 years of research achievements in lithi-um isotopes separation by crown compounds were classified and summarized.%锂有两种稳定的同位素且在核能工业中都有重要的应用,工业上分离锂同位素的方法为锂汞齐法,但该法需使用大量有毒的汞,对人类健康和环境卫生带来了严重问题,因此寻找一种绿色有效的替代方法势在必行。自冠醚和穴醚合成后,在锂同位素分离上的优良特性使其成为了国内外研究热点,本工作将近40年来冠状化合物在锂同位素分离中的研究成果进行了系统的归类和总结,为该领域的进一步研究提供参考。

  8. Determination of plutonium isotopes (238Pu, 239Pu, 240Pu, 241Pu) in environmental samples using radiochemical separation combined with radiometric and mass spectrometric measurements.

    Science.gov (United States)

    Xu, Yihong; Qiao, Jixin; Hou, Xiaolin; Pan, Shaoming; Roos, Per

    2014-02-01

    This paper reports an analytical method for the determination of plutonium isotopes ((238)Pu, (239)Pu, (240)Pu, (241)Pu) in environmental samples using anion exchange chromatography in combination with extraction chromatography for chemical separation of Pu. Both radiometric methods (liquid scintillation counting and alpha spectrometry) and inductively coupled plasma mass spectrometry (ICP-MS) were applied for the measurement of plutonium isotopes. The decontamination factors for uranium were significantly improved up to 7.5 × 10(5) for 20 g soil compared to the level reported in the literature, this is critical for the measurement of plutonium isotopes using mass spectrometric technique. Although the chemical yield of Pu in the entire procedure is about 55%, the analytical results of IAEA soil 6 and IAEA-367 in this work are in a good agreement with the values reported in the literature or reference values, revealing that the developed method for plutonium determination in environmental samples is reliable. The measurement results of (239+240)Pu by alpha spectrometry agreed very well with the sum of (239)Pu and (240)Pu measured by ICP-MS. ICP-MS can not only measure (239)Pu and (240)Pu separately but also (241)Pu. However, it is impossible to measure (238)Pu using ICP-MS in environmental samples even a decontamination factor as high as 10(6) for uranium was obtained by chemical separation.

  9. INTRUDER STATES IN ODD ODD TL NUCLEI POPULATED IN THE ALPHA-DECAY OF ODD ODD BI ISOTOPES

    NARCIS (Netherlands)

    VANDUPPEN, P; DECROCK, P; DENDOOVEN, P; HUYSE, M; REUSEN, G; WAUTERS, J

    1991-01-01

    The alpha-decay of mass separated Bi-190,192,194,196 isotopes has been studied with the LISOL on-line separator. Time sequential alpha-singles spectra were taken and for Bi-190,192,194, alpha-Xt and alpha-gamma-t coincidences were collected. Transition probabilities of levels in Tl-186,188,190 were

  10. INTRUDER STATES IN ODD ODD TL NUCLEI POPULATED IN THE ALPHA-DECAY OF ODD ODD BI ISOTOPES

    NARCIS (Netherlands)

    VANDUPPEN, P; DECROCK, P; DENDOOVEN, P; HUYSE, M; REUSEN, G; WAUTERS, J

    1991-01-01

    The alpha-decay of mass separated Bi-190,192,194,196 isotopes has been studied with the LISOL on-line separator. Time sequential alpha-singles spectra were taken and for Bi-190,192,194, alpha-Xt and alpha-gamma-t coincidences were collected. Transition probabilities of levels in Tl-186,188,190 were

  11. A fully automated simultaneous single-stage separation of Sr, Pb, and Nd using DGA Resin for the isotopic analysis of marine sediments.

    Science.gov (United States)

    Retzmann, A; Zimmermann, T; Pröfrock, D; Prohaska, T; Irrgeher, J

    2017-07-04

    A novel, fast and reliable sample preparation procedure for the simultaneous separation of Sr, Pb, and Nd has been developed for subsequent isotope ratio analysis of sediment digests. The method applying a fully automated, low-pressure chromatographic system separates all three analytes in a single-stage extraction step using self-packed columns filled with DGA Resin. The fully automated set-up allows the unattended processing of three isotopic systems from one sediment digest every 2 h, offering high sample throughput of up to 12 samples per day and reducing substantially laboratory manpower as compared to conventional manual methods. The developed separation method was validated using the marine sediment GBW-07313 as matrix-matched certified reference material and combines quantitative recoveries (>90% for Sr, >93% for Pb, and >91% for Nd) with low procedural blank levels following the sample separation (0.07 μg L(-1) Sr, 0.03 μg L(-1) Pb, and 0.57 μg L(-1) Nd). The average δ values for Sr, Pb, and Nd of the separated reference standards were within the certified ranges (δ ((87)Sr/(86)Sr)NIST SRM 987 of -0.05(28) ‰, δ((208)Pb/(206)Pb)NIST SRM 981 of -0.21(14) ‰, and δ((143)Nd/(144)Nd)JNdi-1 of 0.00(7) ‰). The DGA Resin proved to be reusable for the separation of >10 sediment digests with no significant carry-over or memory effects, as well as no significant on-column fractionation of Sr, Pb, and Nd isotope ratios. Additional spike experiments of NIST SRM 987 with Pb, NIST SRM 981 with Sr, and JNdi-1 with Ce revealed no significant impact on the measured isotopic ratios, caused by potential small analyte peak overlaps during the separation of Sr and Pb, as well as Ce and Nd.

  12. Development of the high temperature ion-source for the Grenoble electromagnetic isotope separator; Etude et realisation de la source d'ions a haute temperature du separateur electromagnetique d'isotopes de Grenoble

    Energy Technology Data Exchange (ETDEWEB)

    Bouriant, M. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1967-12-01

    The production of high purity stable or radioactive isotopes ({>=} 99.99 per cent) using electromagnetic separation require for equipment having a high resolving power. Besides, and in order to collect rare or short half-life isotopes, the efficiency of the ion-source must be high ({eta} > 5 to 10 per cent). With this in view, the source built operates at high temperatures (2500-3000 C) and makes use of ionisation by electronic bombardment or of thermo-ionisation. A summary is given in the first part of this work on the essential characteristics of the isotope separator ion Sources; a diagram of the principle of the source built is then given together with its characteristics. In the second part are given the values of the resolving power and of the efficiency of the Grenoble isotope separator fitted with such a source. The resolving power measured at 10 per cent of the peak height is of the order of 200. At the first magnetic stage the efficiency is between 1 and 26 per cent for a range of elements evaporating between 200 and 3000 C. Thus equipped, the separator has for example given, at the first stage, 10 mg of {sup 180}Hf at (99.69 {+-} 0.1) per cent corresponding to an enrichment coefficient of 580; recently 2 mg of {sup 150}Nd at (99.996 {+-} 0.002) per cent corresponding to an enrichment coefficient of 4.2 x 10{sup 5} has been obtained at the second stage. (author) [French] La production d'isotopes stables ou radioactifs de haute purete isotopique ({>=} 99.99 pour cent), par separation electromagnetique, exige des appareils de haut pouvoir de resolution. En outre, et en vue de collecter des isotopes de tres faible abondance ou de periode tres courte, le rendement des sources d'ions doit etre eleve ({eta} > 5 a 10 pour cent). Dans ce but, la source realisee fonctionne a haute temperature (2500-3000 C) et utilise l'ionisation par bombardement electronique, ou la thermoionisation. Dans la premiere partie de ce travail, on resume d'abord les

  13. Determination of trace metal ions via on-line separation and preconcentration by means of chelating Sepharose beads in a sequential injection lab-on-valve (SI-LOV) system coupled to electrothermal atomic absorption spectrometric detection

    DEFF Research Database (Denmark)

    Long, Xiangbao; Hansen, Elo Harald; Miró, Manuel

    2005-01-01

    . The samples are adjusted to pH 5.0 on-line in the system for optimum operation. The target ions are adsorbed by chelation on the surface of the beads, contained in a 20 mul microcolumn within the LOV, and following elution by 50 mul 2M nitric acid, the eluate is, as sandwiched by air segments, introduced...

  14. Determination of trace metal ions via on-line separation and preconcentration by means of chelating Sepharose beads in a sequential injection lab-on-valve (SI-LOV) system coupled to electrothermal atomic absorption spectrometric detection

    DEFF Research Database (Denmark)

    Long, Xiangbao; Hansen, Elo Harald; Miró, Manuel

    2005-01-01

    The analytical performance of an on-line sequential injection lab-on-valve (SI-LOV) system using chelating Sepharose beads as sorbent material for the determination of ultra trace levels of Cd(II), Pb(II) and Ni(II) by electrothermal atomic absorption spectrometry (ETAAS) is described and discussed...

  15. An isotope approach based on C-13 pulse-chase labelling vs. the root trenching method to separate heterotrophic and autotrophic respiration in cultivated peatlands

    Energy Technology Data Exchange (ETDEWEB)

    Biasi, C.; Pitkamaki, A. S.; Tavi, N. M.; Koponen, H. T.; Martikainen, P. J. [Univ.of Eastern Finland, Kuopio (Finland). Dept. of Environmental Science], e-mail: christina.biasi@uef.fi

    2012-11-01

    We tested an isotope method based on C-13 pulse-chase labelling for determining the fractional contribution of soil microbial respiration to overall soil respiration in an organic soil (cutaway peatland, eastern Finland), cultivated with the bioenergy crop, reed canary grass. The plants were exposed to CO{sub 2}-13 for five hours and the label was thereafter determined in CO{sub 2} derived from the soil-root system. A two-pool isotope mixing model was used to separate sources of respiration. The isotopic approach showed that a minimum of 50% of the total CO{sub 2} originated from soil-microbial respiration. Even though the method uses undisturbed soil-plant systems, it has limitations concerning the experimental determination of the true isotopic signal of all components contributing to autotrophic respiration. A trenching experiment which was comparatively conducted resulted in a 71% fractional contribution of soil-microbial respiration. This value was likely overestimated. Further studies are needed to evaluate critically the output from these two partitioning approaches. (orig.)

  16. Preliminary results from a microvolume, dynamically heated analytical column for preconcentration and separation of simple gases prior to stable isotopic analysis

    Science.gov (United States)

    Panetta, Robert James; Seed, Mike

    2016-04-01

    Stable isotope applications that call for preconcentration (i.e., greenhouse gas measurements, small carbonate samples, etc.) universally call for cryogenic fluids such as liquid nitrogen, dry ice slurries, or expensive external recirculation chillers. This adds significant complexity, first and foremost in the requirements to store and handle such dangerous materials. A second layer of complexity is the instrument itself - with mechanisms to physically move either coolant around the trap, or move a trap in or out of the coolant. Not to mention design requirements for hardware that can safely isolate the fluid from other sensitive areas. In an effort to simplify the isotopic analysis of gases requiring preconcentration, we have developed a new separation technology, UltiTrapTM (patent pending), which leverage's the proprietary Advanced Purge & Trap (APT) Technology employed in elemental analysers from Elementar Analysensysteme GmbH products. UltiTrapTM has been specially developed as a micro volume, dynamically heated GC separation column. The introduction of solid-state cooling technology enables sub-zero temperatures without cryogenics or refrigerants, eliminates all moving parts, and increases analytical longevity due to no boiling losses of coolant . This new technology makes it possible for the system to be deployed as both a focussing device and as a gas separation device. Initial data on synthetic gas mixtures (CO2/CH4/N2O in air), and real-world applications including long-term room air and a comparison between carbonated waters of different origins show excellent agreement with previous technologies.

  17. Well-defined functional mesoporous silica/polymer hybrids prepared by an ICAR ATRP technique integrated with bio-inspired polydopamine chemistry for lithium isotope separation.

    Science.gov (United States)

    Liu, Yuekun; Liu, Xuegang; Ye, Gang; Song, Yang; Liu, Fei; Huo, Xiaomei; Chen, Jing

    2017-05-09

    Mesoporous silica/polymer hybrids with well-preserved mesoporosity were prepared by integrating the initiators for continuous activator regeneration (ICAR) atom transfer radical polymerization (ATRP) technique with the bio-inspired polydopamine (PDA) chemistry. By manipulating the auto-oxidative polymerization of dopamine, uniform PDA layers were deposited on the surfaces and pore walls of ordered mesoporous silicas (OMSs), thereby promoting the immobilization of ATRP initiators. Poly(glycidyl methacrylate) (PGMA) brushes were then grown from the OMSs by using the ICAR ATRP technique. The evolution of the mesoporous silica/polymer hybrids during synthesis, in terms of morphology, structure, surface and porous properties, was detailed. And, parameters influencing the controlled growth of polymer chains in the ICAR ATRP system were studied. Taking advantage of the abundant epoxy groups in the PGMA platform, post-functionalization of the mesoporous silica/polymer hybrids by the covalent attachment of macrocyclic ligands for the adsorptive separation of lithium isotopes was realized. Adsorption behavior of the functionalized hybrids toward lithium ions was fully investigated, highlighting the good selectivity, and effects of temperature, solvent and counter ions. The ability for lithium isotope separation was evaluated. A higher separation factor could be obtained in systems with softer counter anions and lower polarity solvents. More importantly, due to the versatility of the ICAR ATRP technique, combined with the non-surface specific PDA chemistry, the methodology established in this work would provide new opportunities for the preparation of advanced organic-inorganic porous hybrids for broadened applications.

  18. Radiochemical Separation and Measurement by Mass Spectrometry with Magnetic Sector with Inductively Coupled Plasma source (ICP-SFMS of Plutonium Isotopes in Soil Samples

    Directory of Open Access Journals (Sweden)

    C. O. Torres-Cortés

    2016-08-01

    Full Text Available The aim of this work is twofold: to optimize the radiochemical separation of Plutonium (Pu from soil samples, and to measure the Pu concentration. Soil samples were prepared using acid digestion assisted by microwaves; then, Pu purification was carried out with Pu AG1X8 resin. Pu isotopes were measured using Mass Spectrometry with Magnetic Sector with Inductively Coupled Plasma source (ICP-SFMS. In order to reduce the interference due to the presence of 238UH+ in the samples a desolvation system (Apex was used. The limit of detection (LOD of Pu was determined. The efficiency of Pu recovery from soil samples varies from 70 to 93%.

  19. Application of δ13C and δ15N isotopic signatures of organic matter fractions sequentially separated from adjacent arable and forest soils to identify carbon stabilization mechanisms

    Directory of Open Access Journals (Sweden)

    M. Sommer

    2011-10-01

    Full Text Available Identifying the chemical mechanisms behind soil carbon bound in organo-mineral complexes is necessary to determine the degree to which soil organic carbon is stabilized belowground. Analysis of δ13C and δ15N isotopic signatures of stabilized OM fractions along with soil mineral characteristics may yield important information about OM-mineral associations and their processing history. We anlayzed the δ13C and δ15N isotopic signatures from two organic matter (OM fractions along with soil mineral proxies to identify the likely binding mechanisms involved. We analyzed OM fractions hypothesized to contain carbon stabilized through organo-mineral complexes: (1 OM separated chemically with sodium pyrophosphate (OM(PY and (2 OM occluded in micro-structures found in the chemical extraction residue (OM(ER. Because the OM fractions were separated from five different soils with paired forest and arable land use histories, we could address the impact of land use change on carbon binding and processing mechanisms. We used partial least squares regression to analyze patterns in the isotopic signature of OM with established mineral and chemical proxies indicative for certain binding mechanisms. We found different mechanisms predominate in each land use type. For arable soils, the formation of OM(PY-Ca-mineral associations was identified as an important OM binding mechanism. Therefore, we hypothesize an increased stabilization of microbial processed OM(PY through Ca2+ interactions. In general, we found the forest soils to contain on average 10% more stabilized carbon relative to total carbon stocks, than the agricultural counter part. In forest soils, we found a positive relationship between isotopic signatures of OM(PY and the ratio of soil organic carbon content to soil surface area (SOC/SSA. This indicates that the OM(PY fractions of forest soils represent layers of slower exchange not directly attached to mineral surfaces. From the isotopic composition

  20. Silicon isotope separation utilizing infrared multiphoton dissociation of Si{sub 2}F{sub 6} irradiated with two-color CO{sub 2} laser light

    Energy Technology Data Exchange (ETDEWEB)

    Yokoyama, Atsushi; Ohba, Hironori; Hashimoto, Masashi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Ishii, Takeshi; Ohya, Akio [Nuclear Development Corp., Tokai, Ibaraki (Japan); Arai, Shigeyoshi [Hill Research Co. Ltd., Tokyo (Japan)

    2002-08-01

    Silicon isotope separation has been done by utilizing the Infrared Multiphoton Dissociation (IRMPD) of Si{sub 2}F{sub 6} irradiated with two-color CO{sub 2} laser lights. The two-color excitation method improved the separation efficiency keeping the high enrichment factors. For example, 99.74% of {sup 28}Si was obtained at 49.63% dissociation of Si{sub 2}F{sub 6} after the simultaneous irradiation of 200 pulses with 966.23 cm{sup -1} photons (0.084 J/cm{sup 2}) and 954.55 cm{sup -1} photons (0.658 J/cm{sup 2}), while 2000 pulses were needed to obtain 99.35% of {sup 28}Si at 35.6% dissociation in the case of only one-color irradiation at 954.55 cm{sup -1} (0.97 J/cm{sup 2}). (author)

  1. The Resonance Ionization Laser Ion Source RILIS - leading all-rounder of on-line ion sources

    Energy Technology Data Exchange (ETDEWEB)

    Rothe, Sebastian [CERN, Geneva (Switzerland); Institut fuer Physik, Univ. Mainz (Germany); Fedosseev, Valentin; Fink, Daniel; Seliverstov, Maxim [CERN, Geneva (Switzerland); Rossel, Ralf [CERN, Geneva (Switzerland); Institut fuer Physik, Univ. Mainz (Germany); Hochschule RheinMain, Wiesbaden (Germany); Wendt, Klaus [Institut fuer Physik, Univ. Mainz (Germany)

    2012-07-01

    The resonance ionization laser ion source (RILIS) of the on-line isotope separator facility ISOLDE at CERN, is based on the method of stepwise resonant laser excitation and ionization of atoms. The element selectivity of the RILIS complements the mass selection process of the ISOLDE separator magnets to provide high purity ion beams of many isotopes. The RILIS, which now includes two complementary and independent tunable laser systems (dye and titanium:sapphire lasers), has been significantly improved since its first demonstration of selective ionization of Yb isotopes in 1992. Today, on account of the high degree of selectivity for the 27 elements now offered, the annual operation of RILIS exceeds 2500 h, making it the most versatile and commonly used ion source at ISOLDE. The use of a narrow band dye laser enables precision in-source laser spectroscopy of isotope shifts and hyperfine structures of isotopes far from stability as well as the production of isomer pure beams as has been demonstrated for Ag, Cu, Pb, Bi, Po, and Tl. A recent upgrade of the RILIS comprises the incorporation of a complementary all solid state laser system as well as the Laser Ion Source Trap (LIST), which greatly enhances selectivity by suppressing any surface ionized isobars.

  2. Using isotopes of dissolved inorganic carbon species and water to separate sources of recharge in a cave spring, northwestern Arkansas, USA Blowing Spring Cave

    Science.gov (United States)

    Knierim, Katherine Joy; Pollock, Erik; Hays, Phillip D.

    2013-01-01

    Blowing Spring Cave in northwestern Arkansas is representative of cave systems in the karst of the Ozark Plateaus, and stable isotopes of water (δ18O and δ2H) and inorganic carbon (δ13C) were used to quantify soil-water, bedrock-matrix water, and precipitation contributions to cave-spring flow during storm events to understand controls on cave water quality. Water samples from recharge-zone soils and the cave were collected from March to May 2012 to implement a multicomponent hydrograph separation approach using δ18O and δ2H of water and dissolved inorganic carbon (δ13C–DIC). During baseflow, median δ2H and δ18O compositions were –41.6‰ and –6.2‰ for soil water and were –37.2‰ and –5.9‰ for cave water, respectively. Median DIC concentrations for soil and cave waters were 1.8 mg/L and 25.0 mg/L, respectively, and median δ13C–DIC compositions were –19.9‰ and –14.3‰, respectively. During a March storm event, 12.2 cm of precipitation fell over 82 h and discharge increased from 0.01 to 0.59 m3/s. The isotopic composition of precipitation varied throughout the storm event because of rainout, a change of 50‰ and 10‰ for δ2H and δ18O was observed, respectively. Although, at the spring, δ2H and δ18O only changed by approximately 3‰ and 1‰, respectively. The isotopic compositions of precipitation and pre-event (i.e., soil and bedrock matrix) water were isotopically similar and the two-component hydrograph separation was inaccurate, either overestimating (>100%) or underestimating (<0%) the precipitation contribution to the spring. During the storm event, spring DIC and δ13C–DIC decreased to a minimum of 8.6 mg/L and –16.2‰, respectively. If the contribution from precipitation was assumed to be zero, soil water was found to contribute between 23 to 72% of the total volume of discharge. Although the assumption of negligible contributions from precipitation is unrealistic, especially in karst systems where rapid flow

  3. Application of δ13C and δ15N isotopic signatures of organic matter fractions sequentially separated from adjacent arable and forest soils to identify carbon stabilization mechanisms

    Directory of Open Access Journals (Sweden)

    M. Sommer

    2011-03-01

    Full Text Available Identifying the chemical mechanisms behind soil carbon bound in organo-mineral complexes is necessary to determine the degree to which soil organic carbon is stabilized belowground. We used the δ13C and δ15N isotopic signatures from two organic matter (OM fractions from soil to identify the likely binding mechanisms involved. We used OM fractions hypothesized to contain carbon stabilized through organo-mineral complexes: (1 OM separated chemically with sodium pyrophosphate (OM(PY and (2 OM stabilized in microstructures found in the chemical extraction residue (OM(ER. Furthermore, because the OM fractions were separated from five different soils with paired forest and arable land use histories, we could address the impact of land use change on carbon binding and processing mechanisms within these soils. We used partial least squares regression to analyze patterns in the isotopic signature of OM with established proxies of different binding mechanisms. Parsing soil OM into different fractions is a systematic method of dissection, however, we are primarily interested in how OM is bound in soil as a whole, requiring a means of re-assembly. Thus, we implemented the recent zonal framework described by Kleber et al. (2007 to relate our findings to undisturbed soil. The δ15N signature of OM fractions served as a reliable indicator for microbial processed carbon in both arable and forest land use types. The δ13C signature of OM fractions in arable sites did not correlate well with proxies of soil mineral properties while a consistent pattern of enrichment was seen in the δ13C of OM fractions in the forest sites. We found a significant difference in δ13C of pooled OM fractions between the forest and arable land use type although it was relatively small (<1‰. We found different binding mechanisms predominate in each land use type. The isotopic signatures of OM fractions from arable soils were highly related to the clay and silt size particles

  4. Spatial separation of groundwater flow paths from a multi-flow system by a simple mixing model using stable isotopes of oxygen and hydrogen as natural tracers

    Science.gov (United States)

    Nakaya, Shinji; Uesugi, Kenji; Motodate, Yusuke; Ohmiya, Isao; Komiya, Hiroyuki; Masuda, Harue; Kusakabe, Minoru

    2007-09-01

    Stable isotopes of oxygen and hydrogen have the potential to serve as tracers for both source and flow paths in a groundwater system. The ratios of stable isotopes of oxygen (δ18O) and hydrogen (δD) can be used as natural tracer parameters to separate multiflow groundwater paths by applying a simple inversion analysis method to determine the differences between observed and calculated δ18O and δD data in a simple mixing model. The model presented here assumes that the distribution of natural tracers in the steady state is governed by simple mixing between flow paths with a normal distribution of flow rate. When the inversion analysis and simple mixing model were applied to the multiflow system of the Matsumoto Basin, which is surrounded by Japanese alpine ranges, the end-members of the relationship between observed δ18O and δD could be separated spatially into specific groundwater flow paths in the multiflow system of shallow and deep groundwater flow paths.

  5. Growth variability and stable isotope composition of two larval carangid fishes in the East Australian Current: The role of upwelling in the separation zone

    Science.gov (United States)

    Syahailatua, Augy; Taylor, Matthew D.; Suthers, Iain M.

    2011-03-01

    The larvae of two carangid fishes, silver trevally ( Pseudocaranx dentex) and yellowtail scad ( Trachurus novaezelandiae), were compared among coastal water masses and the East Australian Current (EAC). Samples followed a north to south gradient including a southern region of upwelling, generated as the EAC separated from the coast. Mean larval carangid densities were greater in the mixed layer (10-30 m) than the surface, but there was no difference between inshore and offshore stations or along latitudinal gradients. Overall, P. dentex recent larval growth over two days pre-capture was faster than T. novaezelandiae, and faster at inshore, coastal stations than in the EAC. Integrated larval growth rate (mm d -1) was usually faster at inshore stations for both species. T. novaezelandiae were enriched in both nitrogen (δ 15N) and carbon (δ 13C) stable isotopes relative to P. dentex. Larvae of both species captured within the upwelling region were enriched in δ 15N and depleted in δ 13C relative to other sites. Recent larval growth had a significant positive relationship with fluorescence (as a proxy of chlorophyll a biomass), and integrated larval growth rate had a significant positive relationship with fluorescence and larval isotope (δ 15N) composition. Recent and integrated growth of larval T. novaezelandiae and P. dentex was enhanced by EAC separation and upwelling, and also in coastal water; stimulated by food availability, and potentially through exploitation of a different trophic niche.

  6. New Trends in on-line Marketing

    OpenAIRE

    Palkovič, Lukáš

    2011-01-01

    This bachelor thesis deals with new trend of internet marketing, it focuses especially on viral marketing. The theoretical part charasterizes the process of viral campaigns, furthermore deals with the components and aspects of on-line environment. Another separated chapter presents social networks, their place in viral marketing and at last but not least the viral video making process. The practical part contains different analyses of specific viral campaigns. The next and equally the last pa...

  7. Formación on line On line learning

    Directory of Open Access Journals (Sweden)

    O. Grau-Perejoan

    2008-09-01

    Full Text Available La formación on line es una modalidad de enseñanza a distancia basada en las nuevas tecnologías. En este artículo se pretende hacer una introducción a base de describir a grandes rasgos sus características principales: asincronía, no presencialidad, comunicación escrita, función del profesor on line, así como los retos, los riesgos, las ventajas y los inconvenientes que plantea. Se exponen las diferencias entre la formación on line y la formación presencial, de manera que los docentes puedan adaptar de la mejor manera posible sus propuestas formativas a la modalidad on line. Se introduce el importantísimo papel de la planificación y de la fase de diseño y, finalmente, se repasan conceptos útiles para comprender mejor el mundo de la formación on line como son los conceptos entorno virtual de aprendizaje (EVA o Blended Learning (B-Learning.On line learning is a type of distance education based on new technologies. This article's aim is to introduce its main characteristics -asynchrony, non-presentiality, written communication, e-teacher role- as well as its challenges, risks, advantages and limitations. Differences between on line learning and face-to-face learning are presented in order to enable educational professionals to adapt their courses to the on line methodology. Planning and designing are introduced as key phases and, finally, useful concepts such as Virtual Learning Environment (VLE or Blended Learning (B-Learning are reviewed in order to achieve a better understanding of the on line learning field.

  8. Implementation of suitable flow injection/sequential injection on-line sample pretreatment schemes. Separation and preconcentration procedures for the determination of trace metal concentrations by ETAAS and/or ICPMS

    DEFF Research Database (Denmark)

    Hansen, Elo Harald; Wang, Jianhua

    Despite their excellent analytical chemical capacities, ETAAS and ICPMS, nevertheless, often require suitable pretreatment of the sample material in order to obtain the necessary sensitivity and selectivity. Either in order to separate/preconcentrate the analyte material, or because of the presen...

  9. Flow injection and sequential injection: The optimal solutions for executing appropriate on-line separation and preconcentration schemes for detection of trace-level concentrations of metals in complex matrices by ICPMS

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    as these adversely will impair its performance. In the lecture, selected examples of separation/preconcentration FI/SI-procedures for the determination of trace levels of metals will be presented, particular emphasis being placed on the use of the novel “lab-on-valve” (LOV) concept....

  10. Separating Autotrophic and Heterotrophic Contributions to Soil Respiration in Maize-Based Agroecosystems Using Stable Carbon Isotope Ratio Mass Spectrometry.

    Science.gov (United States)

    Amos, B.; Walters, D. T.; Madhavan, S.; Arkebauer, T. J.; Scoby, D. L.

    2005-12-01

    Any effort to establish a carbon budget for a growing crop by means of a thorough accounting of all C sources and sinks will require the ability to discriminate between autotrophic and heterotrophic contributions to soil surface CO2 flux. Autotrophic soil respiration (Ra) is defined as combined root respiration and the respiration of soil microorganisms residing in the rhizosphere and using root-derived carbohydrates as an energy source, while heterotrophic respiration (Rh) is defined as the respiration of soil microorganisms and macroorganisms not directly under the influence of the live root system and using SOM as an energy source. We partition soil surface CO2 flux into its autotrophic and heterotrophic components by combining root exclusion with stable carbon isotope techniques in production scale (~65 ha) maize-based agroecosystems. After flux measurements, small chambers are placed on collars in both root excluded shields and in non-root excluded soil, ambient headspace CO2 is removed using a soda lime trap, and soil-respired C is allowed to collect in the chambers. Soil respiration samples are then collected in 12mL evacuated exetainers and analyzed for δ13C by means of a Finnigan Delta-S isotope ratio mass spectrometer interfaced with a Thermo Finnigan GasBench II and a cryogenic trap to increase CO2 concentration. These δ13C measurements were made throughout the 2005 growing season in maize fields representing three agroecosystems: irrigated continuous maize, irrigated maize-soybean rotation, and rainfed maize soybean rotation. Estimates of autotrophic and heterotrophic soil respiration along with other results of this study will be presented.

  11. A new gas chromatographic separation for the H and C stable isotope ratios determination of coal compounds

    Energy Technology Data Exchange (ETDEWEB)

    Antenucci, C.; Jacquemin, C. [Inst. Scientifique de Service Public, Liege (Belgium); Bouquegneau, J.M.; Dauby, P. [Lab. d`Oceanologie, Univ. de Liege (Belgium); Brasseur, A.; Pirard, J.P. [Lab. de Genie Chimique, Univ. de Liege (Belgium); Letolle, R. [Univ. Pierrre et Marie Curie, Lab. de Geologie Appliquee, Paris (France)

    1997-12-31

    A new completely automatized gas-chromatography technique has been developed in order to separate the different gaseous compounds produced during underground coal gasification for their {sup 13}C/{sup 12}C and D/H iosotope ratio measurements. The technique was designed for separation and collection of H{sub 2}, CO, CO{sub 2}, H{sub 2}O, H{sub 2}S, CH{sub 4} and heavier hydrocarbons which are quantitatively oxidized to CO{sub 2} and/or to H{sub 2}O. (orig.)

  12. [Quantification of separate renal function using Tc 99m DTPA and Tc 99m DMSA. Correlations between individual isotopic data and creatinine clearance].

    Science.gov (United States)

    Chevet, D; Moisan, A; Le Pogamp, P; Le Cloirec, J; Wehbe, B; Herry, J Y

    1984-01-01

    The purpose of this prospective study (30 controls and 100 renal patients) is to compare one to each other the values of renal function measured with: 1--the DTPA 99mTc , 2--the DMSA 99mTc , and 3--the creatinine clearance. After the control values being established, correlations are done for the whole group (n = 130) between the creatinine clearance, the DTPA 99mTc clearance and the fixation rate of the DMSA 99mTc . The correlations obtained are:--Clcr Versus Cldtpa = 0,91.--Clcr Versus % Dmsa = 0,90. - Cldtpa Versus % Dmsa = 0,93. and indicate the two isotopic tests performed give similar quantitative results than creatinine clearance. Camera and computer allow to measure the separate renal function one by one, the two isotopic test giving similar values for each kidney. The results of these studies give a good concordance with the observed diseases, except for partial renal artery stenosis. The pyelic retention of DMSA 99mTc product, in condition of ureteral compression, gives a potential overestimation of this test and is a matter to debate. The extreme simplicity and facility of DMSA 99mTc procedures make this investigation accessible to any patient and give excellent morphological and functional tests. DTPA 99mTc clearances--global and separate kidney--give a more sensitive approach than DMSA 99mTc does because vascular captation , elimination rates could be focused. DTPA 99mTc procedure is to be used in patients with transplanted kidney, silent IVP kidney, contrast media contraindication or for exploring glomerular clearance without urine collection.

  13. First on-line $\\beta$-NMR on oriented nuclei magnetic dipole moments of the $\

    CERN Document Server

    Giles, T; Stone, N J; Van Esbroeck, K; White, G; Wöhr, A; Veskovic, M; Towner, I S; Mantica, P F; Prisciandaro, J I; Morrissey, D J; Fedosseev, V; Mishin, V I; Köster, U; Walters, W B

    2000-01-01

    The first fully on-line use of the angular distribution of $\\beta$ - emission in detection of NMR of nuclei oriented at low temperatures is reported. The magnetic moments of the single valence particle, intermediate mass, isotopes $^{67}$Ni($\

  14. Mass measurements on radioactive isotopes using the ISOLTRAP spectrometer

    CERN Document Server

    Dilling, J; Kluge, H J; Kohl, A; Lamour, E; Marx, G; Schwarz, S C; Bollen, G; Kellerbauer, A G; Moore, R B; Henry, S

    2000-01-01

    ISOLTRAP is a Penning trap mass spectrometer installed at the on line isotope separator ISOLDE at CERN. Direct measurements of the masses of short lived radio isotopes are performed using the existing triple trap system. This consists of three electromagnetic traps in tandem: a Paul trap to accumulate and bunch the 60 keV dc beam, a Penning trap for cooling and isobar separation, and a precision Penning trap for the determination of the masses by cyclotron resonance. Measurements of masses of unknown mercury isotopes and in the vicinity of doubly magic /sup 208/Pb are presented, all with an accuracy of delta m/m approximately=1*10/sup -7/. Developments to replace the Paul trap by a radiofrequency quadrupole ion guide system to increase the collection efficiency are presently under way and the status is presented. (10 refs).

  15. The User-friendly On-Line Diffusion Chamber

    CERN Document Server

    Aviles Acosta, Jaime

    2015-01-01

    The On-Line Diffusion Chamber is a stand-alone apparatus built to carry out short-live radiotracer diffusion studies. The availability of the on-demand production of isotopes in the ISOLDE facility, and the design of the apparatus to streamline the implantation process, annealing treatment, ion gun ablation with a tape transport system, and radiation intensity measurement with a Ge gamma detector all in the same apparatus, gives the On-Line Diffusion Chamber a unique ability to studies with short-lived radioisotopes or isomer states that are not possible in any other facility in the world.

  16. Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Portsmouth Gaseous Diffusion Plant site

    Energy Technology Data Exchange (ETDEWEB)

    Marmer, G.J.; Dunn, C.P.; Filley, T.H.; Moeller, K.L.; Pfingston, J.M.; Policastro, A.J.; Cleland, J.H.

    1991-09-01

    Uranium enrichment in the United States has utilized a diffusion process to preferentially enrich the U-235 isotope in the uranium product. In the 1970s, the US Department of Energy (DOE) began investigating more efficient and cost-effective enrichment technologies. In January 1990, the Secretary of Energy approved a plan for the demonstration and deployment of the Uranium Atomic Vapor Laser isotope Separation (U-AVLIS) technology with the near-term goal to provide the necessary information to make a deployment decision by November 1992. Initial facility operation is anticipated for 1999. A programmatic document for use in screening DOE sites to locate a U-AVLIS production plant was developed and implemented in two parts. The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. The final evaluation, which included sensitivity studies, identified the Oak Ridge Gaseous Diffusion Plant (ORGDP) site, the Paducah Gaseous Diffusion Plant (PGDP) site, and the Portsmouth Gaseous Diffusion Plant (PORTS) site as having significant advantages over the other sites considered. This environmental site description (ESD) provides a detailed description of the PORTS site and vicinity suitable for use in an environmental impact statement (EIS). This report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during site visits. The organization of the ESD is as follows. Topics addressed in Sec. 2 include a general site description and the disciplines of geology, water resources, biotic resources, air resources, noise, cultural resources, land use. Socioeconomics, and waste management. Identification of any additional data that would be required for an EIS is presented in Sec. 3.

  17. Determination of plutonium isotopes (238Pu, 239Pu, 240Pu, 241Pu) in environmental samples using radiochemical separation combined with radiometric and mass spectrometric measurements

    DEFF Research Database (Denmark)

    Xu, Yihong; Qiao, Jixin; Hou, Xiaolin

    2014-01-01

    This paper reports an analytical method for the determination of plutonium isotopes (238Pu, 239Pu, 240Pu, 241Pu) in environmental samples using anion exchange chromatography in combination with extraction chromatography for chemical separation of Pu. Both radiometric methods (liquid scintillation...

  18. METHOD OF ISOTOPE CONCENTRATION

    Science.gov (United States)

    Spevack, J.S.

    1957-04-01

    An isotope concentration process is described which consists of exchanging, at two or more different temperature stages, two isotopes of an element between substances that are physically separate from each other and each of which is capable of containing either of the isotopes, and withdrawing from a point between at least two of the temperatare stages one of the substances containing an increased concentration of the desired isotope.

  19. CERN Video News on line

    CERN Multimedia

    2003-01-01

    The latest CERN video news is on line. In this issue : an interview with the Director General and reports on the new home for the DELPHI barrel and the CERN firemen's spectacular training programme. There's also a vintage video news clip from 1954. See: www.cern.ch/video or Bulletin web page

  20. Selenium speciation and isotope composition in 77Se-enriched yeast using gradient elution HPLC separation and ICP-dynamic reaction cell-MS

    DEFF Research Database (Denmark)

    Larsen, Erik Huusfeldt; Sloth, Jens Jørgen; Hansen, M.

    2003-01-01

    A batch of Se-77-labelled and enriched yeast was characterised with regard to isotopic composition and content of selenium species for later use in a human absorption study based on the method of enriched stable isotopes. The abundance of the six stable selenium isotopes was determined by ICP- MS...... equipped with a dynamic reaction cell (DRC). The results showed that the Se-77 isotope was enriched to 98.5 atom-%, whereas the remaining selenium was present as the other five isotopes at low abundance. The low-molecular Se-77 containing species, which were biosynthesised by the yeast during fermentation...

  1. Momentum transport cross-section measurements for potassium and rubidium in rare gases and white light-induced separation of rubidium isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Mugglin, D.T.

    1993-12-31

    This dissertation is concerned with two light-induced kinetic effects, light-induced diffusive pulling and light-induced drift. We use a light-induced diffusive pulling experiment to measure the ground state velocity-changing collision cross section (related to the momentum transport cross section and the diffusion coefficient) and the relative difference ({Delta}{sigma}/{sigma}) of the excited and ground state cross sections with respect to that of the ground state for potassium mixed with inert buffer gases. The measured excited state cross section is a weighted average of the potassium 4{sup 2}P{sub 1/2} and 4{sup 2}P{sub 3/2} fine structure levels, which are mixed by collisions with inert gas atoms. For the ground state cross sections, we obtain the following experimental results for potassium mixed with He, Ne, Ar, Kr, and Xe, respectively: 52 {+-} 4, 57 {+-} 8, 61 {+-} 5, 43 {+-} 5, and 60 {+-}5 {angstrom}{sup 2}. For {Delta}{sigma}/{sigma}, we obtain the following (in the same order): 0.085 {+-} 0.010, 0.058 {+-} 0.006, 0.41 {+-} 0.03, 0.43 {+-} 0.03, and 0.61 {+-} 0.05. For potassium-Ne and potassium-Ar, we combine these measurements with light-induced drift measurements of the ratio {Delta}{sigma}(J = 3/2) : {Delta}{sigma}(J = 1/2) to obtain absolute transport cross sections for the individual 4{sup 2}S{sub 1/2}, 4{sup 2}P{sub 1/2}, and 4{sup 2}P{sub 3/2} levels. We also use the light-induced diffusive pulling experimental method to measure {Delta}{sigma}/{sigma} for Rb-inert gas mixtures. We obtain values for the ground state diffusion cross section for Rb in several of the inert gases as well. We report the first experimental observation of the separation of two isotopes using broadband light by the process of white light-induced drift. For a light source, we use a broadband laser with an acousto-optic modulator as an output coupler. We verify the separation of the {sup 85}Rb and {sup 87}Rb isotopes.

  2. From User Comments to On-line Conversations

    OpenAIRE

    Wang, Chunyan; Ye, Mao; Huberman, Bernardo A.

    2012-01-01

    We present an analysis of user conversations in on-line social media and their evolution over time. We propose a dynamic model that accurately predicts the growth dynamics and structural properties of conversation threads. The model successfully reconciles the differing observations that have been reported in existing studies. By separating artificial factors from user behaviors, we show that there are actually underlying rules in common for on-line conversations in different social media web...

  3. A field survey of metal binding to metallothionein and other cytosolic ligands in liver of eels using an on-line isotope dilution method in combination with size exclusion (SE) high pressure liquid chromatography (HPLC) coupled to Inductively Coupled Plasma time-of-flight Mass Spectrometry (ICP-TOFMS).

    Science.gov (United States)

    Van Campenhout, Karen; Goenaga Infante, Heidi; Goemans, Geert; Belpaire, Claude; Adams, Freddy; Blust, Ronny; Bervoets, Lieven

    2008-05-15

    The effect of metal exposure on the accumulation and cytosolic speciation of metals in livers of wild populations of European eel with special emphasis on metallothioneins (MT) was studied. Four sampling sites in Flanders showing different degrees of heavy metal contamination were selected for this purpose. An on-line isotope dilution method in combination with size exclusion (SE) high pressure liquid chromatography (HPLC) coupled to Inductively Coupled Plasma time-of-flight Mass Spectrometry (ICP-TOFMS) was used to study the cytosolic speciation of the metals. The distribution of the metals Cd, Cu, Ni, Pb and Zn among cytosolic fractions displayed strong differences. The cytosolic concentration of Cd, Ni and Pb increased proportionally with the total liver levels. However, the cytosolic concentrations of Cu and Zn only increased above a certain liver tissue threshold level. Cd, Cu and Zn, but not Pb and Ni, were largely associated with the MT pool in correspondence with the environmental exposure and liver tissue concentrations. Most of the Pb and Ni and a considerable fraction of Cu and Zn, but not Cd, were associated to High Molecular Weight (HMW) fractions. The relative importance of the Cu and Zn in the HMW fraction decreased with increasing contamination levels while the MT pool became progressively more important. The close relationship between the cytosolic metal load and the total MT levels or the metals bound on the MT pool indicates that the metals, rather than other stress factors, are the major factor determining MT induction.

  4. Nucleon-induced fission cross-sections of tantalum and separated tungsten isotopes and "compound nucleus" effect in intermediate energy region

    CERN Document Server

    Smirnov, A N; Eismont, V P; Filatov, N P; Blomgren, J; Conde, H; Prokofiev, A V; Mashnik, S G

    2007-01-01

    Neutron- and proton-induced fission cross-sections of separated isotopes of tungsten (182W, 183W, 184W, and 186W) and 181Ta relative to 209Bi have been measured in the incident nucleon energy region 50 - 200 MeV using fission chambers based on thin-film breakdown counters (TFBC) using quasi-monoenergetic neutrons from the 7Li(p,n) reaction and at the proton beams of The Svedberg Laboratory (TSL), Uppsala University (Uppsala, Sweden). The results are compared with predictions by the CEM03.01 event generator, as well as with the recent data for nuclei in the lead-bismuth region. The effect of "compound nucleus" in the intermediate energy region is discussed, displaying in exponential dependence of nucleon-induced fission cross-sections on the parameter Z^2/A of the composite system (projectile+target nucleus), and in other characteristics of the fission process for which parameter Z^2/A plays a role similar to the one of the usual liquid-drop parameter Z^2/A of compound nuclei.

  5. Clean Air OnLine

    Energy Technology Data Exchange (ETDEWEB)

    Finney, D. [Environment Canada, Gatineau, PQ (Canada). Air Pollution Prevention Directorate

    2004-04-07

    This presentation describes Clean Air OnLine, a multi-tiered website dedicated to providing Canadians with information on air quality. The website is under development to support action to reduce air emissions, demonstrate the links between air emissions and environmental impacts, and enhance the understanding of sustainable community development issues such as health, energy, and urban sprawl. Partners in the Clean Air OnLine (CAOL) initiative include Environment Canada and the Clean Air Partnership which includes the Greater Toronto Area pilot project. The audience for CAOL includes municipal decision makers, local decision makers, community leaders, and the general public. The project provides Canadians with air pollution contextual information on pollution sources, pollutants, and related issues. It also provides information on health, environmental and economic impacts and the interrelationships with climate change issues and energy use. tabs., figs.

  6. On-line moisture analysis

    CERN Document Server

    Cutmore, N G

    2002-01-01

    Measurement of the moisture content of iron ore has become a key issue for controlling moisture additions for dust suppression. In most cases moisture content is still determined by manual or automatic sampling of the ore stream, followed by conventional laboratory analysis by oven drying. Although this procedure enables the moisture content to be routinely monitored, it is too slow for control purposes. This has generated renewed interest in on-line techniques for the accurate and rapid measurement of moisture in iron ore on conveyors. Microwave transmission techniques have emerged over the past 40 years as the dominant technology for on-line measurement of moisture in bulk materials, including iron ores. Alternative technologies have their limitations. Infra-red analysers are used in a variety of process industries, but rely on the measurement of absorption by moisture in a very thin surface layer. Consequently such probes may be compromised by particle size effects and biased presentation of the bulk mater...

  7. Study of the bipolar electrolysis of the tritiated water applied to the hydrogen isotopes separation by electrochemical permeation threw Pd-Ag alloy membranes; Etude de l'electrolyse bipolaire de l'eau tritiee appliquee a la separation des isotopes de l'hydrogene par permeation electrochimique a travers des membranes d'alliage PD-AG

    Energy Technology Data Exchange (ETDEWEB)

    Heinze, S

    2000-07-01

    The objective of the study is to enrich waters of poor tritium concentration, by electrolysis in the same time of an hydrogen emission of low activity. In this framework the hydrogen electrochemical permeation threw Pd-Ag alloy membranes has been used. The first part of the study concerns the hydrogen and the deuterium diffusion threw these membranes. The activation and the thermal treatments influence have been studied. A relation between the membrane microstructure and the diffusion mechanism has been proposed. The second part of the study is devoted to the hydrogen gate mechanism determination in the membrane by impedance spectroscopy. The last part concerns the determination of the isotopic separation factor hydrogen-deuterium. Experimental results agree the calculated theoretical data. The operation of an operational membrane cell has been simulated and the process feasibility has been proved. (A.L.B.)

  8. Masses of neutron-rich Ni and Cu isotopes and the shell closure at Z=28,N=40

    Energy Technology Data Exchange (ETDEWEB)

    Rahaman, S.; Hakala, J.; Elomaa, V.V.; Eronen, T.; Hager, U.; Jokinen, A.; Kankainen, A.; Moore, I.D.; Penttilae, H.; Rinta-Antila, S.; Rissanen, J.; Saastamoinen, A.; Weber, C.; Aeystoe, J. [University of Jyvaeskylae, Department of Physics, P.O. Box 35 (YFL) (Finland)

    2007-10-15

    The Penning trap mass spectrometer JYFLTRAP, coupled to the Ion Guide Isotope Separator On-Line (IGISOL) facility at Jyvaeskylae, was employed to measure the atomic masses of neutron-rich {sup 70-73}Ni and {sup 73,} {sup 75}Cu isotopes with a typical accuracy less than 5 keV. The mass of {sup 73}Ni was measured for the first time. Comparisons with the previous data are discussed. Two-neutron separation energies show a weak subshell closure at {sup 68} {sub 28}Ni{sub 40}. A well established proton shell gap is observed at Z=28. (orig.)

  9. Generation of Radixenon Isotopes

    Energy Technology Data Exchange (ETDEWEB)

    McIntyre, Justin I.; Bowyer, Ted W.; Hayes, James C.; Heimbigner, Tom R.; Morris, Scott J.; Panisko, Mark E.; Pitts, W. K.; Pratt, Sharon L.; Reeder, Paul L.; Thomas, Charles W.

    2003-06-30

    Pacific Northwest National Laboratory has developed an automated system for separating Xe from air and can detect the following radioxenon isotopes, 131mXe, 133mXe, 133Xe, and 135Xe. This report details the techniques used to generate the various radioxenon isotopes that are used for the calibration of the detector as well as other isotopes that have the potential to interfere with the fission produced radioxenon isotopes. Fission production is covered first using highly enriched uranium followed by a description and results from an experiment to produce radioxenon isotopes from neutron activation of ambient xenon.

  10. PHENIX on-line systems

    Energy Technology Data Exchange (ETDEWEB)

    Adler, S.S.; Allen, M.; Alley, G.; Amirikas, R.; Arai, Y.; Awes, T.C.; Barish, K.N.; Barta, F.; Batsouli, S.; Belikov, S.; Bennett, M.J.; Bobrek, M.; Boissevain, J.G.; Boose, S.; Britton, C.; Britton, L.; Bryan, W.L.; Cafferty, M.M.; Carey, T.A.; Chang, W.C.; Chi, C.Y.; Chiu, M.; Cianciolo, V.; Cole, B.A.; Constantin, P.; Cook, K.C.; Cunitz, H.; Desmond, E.J.; Ebisu, K.; Efremenko, Y.V.; El Chenawi, K.; Emery, M.S.; Engo, D.; Ericson, N.; Fields, D.E.; Frank, S.; Frantz, J.E.; Franz, A.; Frawley, A.D.; Fried, J.; Gannon, J.; Gee, T.F.; Gentry, R.; Giannotti, P.; Gustafsson, H.-A.; Haggerty, J.S.; Hahn, S.; Halliwell, J.; Hamagaki, H.; Hansen, A.G.; Hara, H.; Harder, J.; He, X.; Heistermann, F.; Hemmick, T.K.; Hibino, M.; Hill, J.C. E-mail: jhill@iastate.edu; Homma, K.; Jacak, B.V.; Jagadish, U.; Jia, J.; Kajihara, F.; Kametani, S.; Kamyshkov, Y.; Kandasamy, A.; Kang, J.H.; Kapustinsky, J.; Katou, K.; Kelley, M.A.; Kelly, S.; Kikuchi, J.; Kim, S.Y.; Kim, Y.G.; Kistenev, E.; Kotchetkov, D.; Kurita, K.; Lajoie, J.G.; Lenz, M.; Lenz, W.; Li, X.H.; Lin, S.; Liu, M.X.; Markacs, S.; Matathias, F.; Matsumoto, T.; Mead, J.; Mischke, R.E.; Mishra, G.C.; Moore, A.; Muniruzzamann, M.; Musrock, M.; Nagle, J.L.; Nandi, B.K.; Newby, J.; Nystrand, J.; O' Brien, E.; O' Connor, P.; Ohnishi, H.; Oskarsson, A.; Osterman, L.; Oyama, K.; Paffrath, L.; Pancake, C.E.; Pantuev, V.S.; Petridis, A.N.; Pisani, R.P.; Plagge, T.; Plasil, F.; Purschke, M.L.; Rankowitz, S.; Rao, R.; Rau, M.; Read, K.F.; Ryu, S.S.; Sakaguchi, T.; Sato, H.D.; Seto, R.; Shiina, T.; Silvermyr, D.; Simon-Gillo, J.; Simpson, M.; Sippach, W.; Skank, H.D.; Skutnik, S.; Sleege, G.A.; Smith, G.D.; Smith, M.; Stankus, P.W.; Steinberg, P.; Sugitate, T.; Sullivan, J.P.; Taketani, A.; Tamai, M.; Tanaka, Y.; Thomas, W.D.; Todd, R.; Toldo, F.; Turner, G.; Ushiroda, T.; Velkovska, J.; Hecke, H.W. van; Lith, M. van; Villatte, L.; Achen, W. von; Walker, J.W.; Wang, H.Q.; White, S.N.; Wintenberg, A.L.; Witzig, C.; Wood, L.[and others

    2003-03-01

    The PHENIX On-Line system takes signals from the Front End Modules (FEM) on each detector subsystem for the purpose of generating events for physics analysis. Processing of event data begins when the Data Collection Modules (DCM) receive data via fiber-optic links from the FEMs. The DCMs format and zero suppress the data and generate data packets. These packets go to the Event Builders (EvB) that assemble the events in final form. The Level-1 trigger (LVL1) generates a decision for each beam crossing and eliminates uninteresting events. The FEMs carry out all detector processing of the data so that it is delivered to the DCMs using a standard format. The FEMs also provide buffering for LVL1 trigger processing and DCM data collection. This is carried out using an architecture that is pipelined and deadtimeless. All of this is controlled by the Master Timing System (MTS) that distributes the RHIC clocks. A Level-2 trigger (LVL2) gives additional discrimination. A description of the components and operation of the PHENIX On-Line system is given and the solution to a number of electronic infrastructure problems are discussed.

  11. Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Oak Ridge Gaseous Diffusion Plant Site

    Energy Technology Data Exchange (ETDEWEB)

    1991-09-01

    In January 1990, the Secretary of Energy approved a plan for the demonstration and deployment of the Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) technology, with the near-term goal to provide the necessary information to make a deployment decision by November 1992. The U-AVLIS process is based on electrostatic extraction of photoionized U-235 atoms from an atomic vapor stream created by electron-beam vaporization of uranium metal alloy. A programmatic document for use in screening DOE sites to locate the U-AVLIS production plant was developed and implemented in two parts (Wolsko et al. 1991). The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. These sites were then subjected to a more rigorous and detailed comparative analysis for the purpose of developing a short list of reasonable alternative sites for later environmental examination. This environmental site description (ESD) provides a detailed description of the ORGDP site and vicinity suitable for use in an environmental impact statement (EIS). The report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during a site visit. The organization of the ESD is as follows. Topics addressed in Sec. 2 include a general site description and the disciplines of geology, water resources, biotic resources, air resources, noise, cultural resources, land use, socioeconomics, and waste management. Identification of any additional data that would be required for an EIS is presented in Sec. 3. Following the site description and additional data requirements, Sec. 4 provides a short, qualitative assessment of potential environmental issues. 37 refs., 20 figs., 18 tabs.

  12. On-line sample treatment - Capillary gas chromatography

    NARCIS (Netherlands)

    Goosens, EC; de Jong, D; de Jong, GJ; Brinkman, UAT

    1998-01-01

    Sample pretreatment is often the bottleneck of a trace level analytical procedure. In order to increase performance, increasing attention is therefore being devoted to combining sample pretreatment on-line with the separation technique that has to be used. In the present review, a variety of procedu

  13. Production of neutron-rich isotopes by one- and two-step processes in ISOL targets

    CERN Document Server

    Portillo, M; Gomes, I; Panteleev, V N; Fedorov, D V; Barzakh, A E; Beznosjuk, V I; Moroz, F V; Orlov, S Y; Volkov, Y M

    2002-01-01

    The results are presented for an experiment that compares the difference between a one- and two-step reaction setup using 1 GeV protons. The rates of production from an on-line isotope separator target containing UCx are measured for isotopes in the neutron mass region of Rb and Cs. Some details about the measured results and predictions by the Monte Carlo models are discussed. The effects of the delayed release on the extracted efficiency are generalized using analytical models for application to a wide range of nuclear decay lifetimes.

  14. High-accuracy mass determination of unstable cesium and barium isotopes

    CERN Document Server

    Ames, F; Beck, D; Bollen, G; De Saint-Simon, M; Jertz, R; Kluge, H J; Kohl, A; König, M; Lunney, M D; Martel, I; Moore, R B; Otto, T; Patyk, Z; Raimbault-Hartmann, H; Rouleau, G; Savard, G; Schark, E; Schwarz, S; Schweikhard, L; Stolzenberg, H; Szerypo, J

    1999-01-01

    Direct mass measurements of short-lived Cs and Ba isotopes have been performed with the tandem Penning trap mass spectrometer ISOLTRAP installed at the on-line isotope separator ISOLDE at CERN. Typically, a mass resolving power of 600 000 and an accuracy of $\\delta \\mbox{m} \\approx 13$ keV have been obtained. The masses of $^{123,124,126}$Ba and $^{122m}$Cs were measured for the first time. A least-squares adjustment has been performed and the experimental masses are compared with theoretical ones, particularly in the frame of a macroscopic-microscopic model.

  15. Isomer separation and measurement of nuclear moments with the ISOLDE RILIS

    Energy Technology Data Exchange (ETDEWEB)

    Koester, U.; Catherall, R. [ISOLDE, CERN (Switzerland); Fedoseyev, V.N. [Russian Academy of Sciences, Institute of Spectroscopy (Russian Federation); Franchoo, S. [K.U. Leuven, Instituut voor Kern en Stralingsfysica (Belgium); Georg, U. [ISOLDE, CERN (Switzerland); Huyse, M.; Kruglov, K. [K.U. Leuven, Instituut voor Kern en Stralingsfysica (Belgium); Lettry, J. [ISOLDE, CERN (Switzerland); Mishin, V.I. [Russian Academy of Sciences, Institute of Spectroscopy (Russian Federation); Oinonen, M.; Ravn, H. [ISOLDE, CERN (Switzerland); Seliverstov, M.D. [St. Petersburg Nuclear Physics Institute (Russian Federation); Simon, H. [ISOLDE, CERN (Switzerland); Van Duppen, P.; Van Roosbroeck, J.; Weissman, L. [K.U. Leuven, Instituut voor Kern en Stralingsfysica (Belgium)

    2000-08-15

    Short-lived radioisotopes are element selectively ionized by the resonance ionization laser ion source (RILIS) of the on-line isotope separator ISOLDE (CERN). The relative production of low and high spin isomers can be significantly changed when a narrow-bandwidth laser is used to scan through the atomic hyperfine structure. This allows the assignment of gamma ray transitions to the decay of the individual isomers. Moreover, the measurement of the hyperfine splitting provides a very sensitive method for the determination of magnetic moments of exotic isotopes. The technical developments are discussed for the example of copper.

  16. New insight from noble gas and stable isotopes of geothermal/hydrothermal fluids at Caviahue-Copahue Volcanic Complex: Boiling steam separation and water-rock interaction at shallow depth

    Science.gov (United States)

    Roulleau, Emilie; Tardani, Daniele; Sano, Yuji; Takahata, Naoto; Vinet, Nicolas; Bravo, Francisco; Muñoz, Carlos; Sanchez, Juan

    2016-12-01

    We measured noble gas and stable isotopes of the geothermal and hydrothermal fluids of the Caviahue-Copahue Volcanic Complex (CCVC), one of the most important geothermal systems in Argentina/Chile, in order to provide new insights into fluid circulation and origin. With the exception of Anfiteatro and Chancho-co geothermal systems, mantle-derived helium dominates in the CCVC fluids, with measured 3He/4He ratios up to 7.86Ra in 2015. Their positive δ15N is an evidence for subducted sediment-derived nitrogen, which is commonly observed in subduction settings. Both He-N2-Ar composition and positive correlation between δD-H2O and δ18O-H2O suggest that the fluids from Anfiteatro and Chancho-co (and partly from Pucon-Mahuida as well, on the southern flank of Copahue volcano) represent a meteoric water composition with a minor magmatic contribution. The Ne, Kr and Xe isotopic compositions are entirely of atmospheric origin, but processes of boiling and steam separation have led to fractionation of their elemental abundances. We modeled the CCVC fluid evolution using Rayleigh distillation curves, considering an initial air saturated geothermal water (ASGW) end-member at 250 and 300 °C, followed by boiling and steam separation at lower temperatures (from 200 °C to 150 °C). Between 2014 and 2015, the CCVC hydrogen and oxygen isotopes shifted from local meteoric water-dominated to andesitic water-dominated signature. This shift is associated with an increase of δ13C values and Stotal, HCl and He contents. These characteristics are consistent with a change in the gas ascent pathway between 2014 and 2015, which in turn induced higher magmatic-hydrothermal contribution in the fluid signature. The composition of the magmatic source of the CCVC fluids is: 3He/4He = 7.7Ra, δ15N = + 6‰, and δ13C = - 6.5‰. Mixing models between air-corrected He and N suggest the involvement of 0.5% to 5% of subducted sediments in the magmatic source. The magmatic sulfur isotopic

  17. Oxygen isotope composition of water and snow-ice cover of isolated lakes at various stages of separation from the White Sea

    Science.gov (United States)

    Lisitzin, A. P.; Vasil'chuk, Yu. K.; Shevchenko, V. P.; Budantseva, N. A.; Krasnova, E. D.; Pantyulin, A. N.; Filippov, A. S.; Chizhova, Ju. N.

    2013-04-01

    This study aimed to analyze the oxygen isotope composition of water, ice, and snow in water bodies isolated from the White Sea and to identify the structural peculiarities of these pools during the winter period. The studies were performed during early spring in Kandalaksha Bay of the White Sea, in Velikaya Salma Strait and in Rugoserskaya Inlet. The studied water bodies differ in their degree of isolation from the sea. In particular, Ermolinskaya Inlet has normal water exchange with the sea; the Lake on Zelenyi Cape represents the first stage of isolation; i. e., it has permanent water exchange with the sea by the tide. Kislo-Sladkoe Lake receives sea water from time to time. Trekhtsvetnoe Lake is totally isolated from the sea and is a typical meromictic lake. Finally, Nizhnee Ershovskoe Lake exhibits some features of a saline water body. The oxygen isotope profile of the water column in Trekhtsvetnoe Lake allows defining three layers; this lake may be called typically meromictic. The oxygen isotope profile of the water column in Kislo-Sladkoe Lake is even from the surface to the bottom. The variability of δ18O is minor in Lake on Zelenyi Cape. A surface layer (0-1 m) exists in Nizhnee Ershovskoe Lake, and the oxygen isotope variability is well pronounced. Deeper, where the freshwater dominates, the values of ?18Îvary insignificantly disregarding the water depth and temperature. This fresh water lake is not affected by the seawater and is not stratified according to the isotope profile. It is found that applying the values of ?18Î and profiles of temperature and salinity may appear as an effective method in defining the water sources feeding the water bodies isolated from the sea environment.

  18. Are on-line currencies virtual banknotes?

    OpenAIRE

    Stephen F. Quinn; William Roberds

    2003-01-01

    The history of money is marked by innovations that have expanded the role of "inside money"-money created by the private sector. For instance, the past few years have seen the development of several types of on-line payment arrangements, some of which have been dubbed "on-line currencies." ; This article examines the likely success or failure of on-line currencies by means of a historical analogy. The discussion compares the introduction of on-line currencies to the debut of the bearer bankno...

  19. Systematization of cross sections for the production of residual nuclei on separated tin isotopes in reactions induced by various-energy protons

    Energy Technology Data Exchange (ETDEWEB)

    Balabekyan, A. R., E-mail: balabekyan@ysu.am; Danagulyan, A. S. [Yerevan State University (Armenia); Drnoyan, J. R.; Demekhina, N. A. [Joint Institute for Nuclear Research (Russian Federation); Hovhannisyan, G. H.; Simonyan, A. E. [Yerevan State University (Armenia); Adam, J.; Solnishkin, A. A.; Tsoupko-Sytnikov, V. M. [Joint Institute for Nuclear Research (Russian Federation)

    2011-05-15

    Cross sections for the production of residual nuclei on the isotopes {sup 112,118,120,124}Sn irradiated with 0.66-, 1.0-, 3.65-, and 8.1-GeV proton beams were investigated. A ten-parameter semiempirical formula was used to systematize the cross sections in question. A comparative analysis of parameter values obtained at different proton energies was performed.

  20. On the sequential separation and quantification of (237)Np, (241)Am, thorium, plutonium, and uranium isotopes in environmental and urine samples.

    Science.gov (United States)

    Vasile, M; Jacobs, K; Bruggeman, M; Van Hoecke, K; Dobney, A; Verrezen, F

    2017-07-13

    The implementation of the one-pass-through separation technique using two stacked chromatography columns of TEVA - TRU resins for the separation of (237)Np, (241)Am, thorium, plutonium and uranium from environmental and urine samples was investigated. The sequential separation technique proved to be successful and gave similar results to those obtained when using individual separations. The analysis time was considerably improved. The amount of chemical waste was also reduced by 50% and the use of HClO4 was avoided. The technique of ICP-MS was also investigated as a complementary technique to alpha-spectrometry. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. On line routing per mobile phone

    DEFF Research Database (Denmark)

    Bieding, Thomas; Görtz, Simon; Klose, Andreas

    2009-01-01

    On-line routing is concerned with building vehicle routes in an ongoing fashion in such a way that customer requests arriving dynamically in time are efficiently and effectively served. An indispensable prerequisite for applying on-line routing methods is mobile communication technology. Addition...

  2. Direct High-Precision Measurements of the (87)Sr/(86)Sr Isotope Ratio in Natural Water without Chemical Separation Using Thermal Ionization Mass Spectrometry Equipped with 10(12) Ω Resistors.

    Science.gov (United States)

    Li, Chao-Feng; Guo, Jing-Hui; Chu, Zhu-Yin; Feng, Lian-Jun; Wang, Xuan-Ce

    2015-07-21

    Thermal ionization mass spectrometry (TIMS) allows excellent precision for determining Sr isotope ratios in natural water samples. Traditionally, a chemical separation procedure using cation exchange resin has been employed to obtain a high purity Sr fraction from natural water, which makes sample preparation time-consuming. In this study, we present a rapid and precise method for the direct determination of the Sr isotope ratio of natural water using TIMS equipped with amplifiers with two 10(12) Ω resistors. To eliminate the (87)Rb isobaric interference, Re ribbons are used as filaments, providing a significant advantage over W ribbons in the inhibition of Rb(+) emission, based on systematically examining a series of NIST SRM987 standard doping with various amounts of Rb using Re and W ribbons. To validate the applicability of our method, twenty-two natural water samples, including different water types (rain, snow, river, lake and drinking water), that show a large range in Sr content variations (2.54-922.8 ppb), were collected and analyzed from North and South China. Analytical results show good precision (0.003-0.005%, 2 RSE) and the method was further validated by comparative analysis of the same water with and without chemical separation. The method is simple and rapid, eliminates sample preparation time, and prevents potential contamination during complicated sample-preparation procedures. Therefore, a high sample throughput inherent to the TIMS can be fully utilized.

  3. EBIS/T charge breeding for intense rare isotope beams at MSU

    CERN Document Server

    Schwarz, S; Marrs, R E; Kittimanapun, K; Lapierre, A; Mendez, A J; Ames, F; Beene, J R; Lindroos, M; Ahle, L E; Stracener, D W; Kester, O; Wenander, F; Lopez-Urrutia, J R Crespo; Dilling, J; Bollen, G

    2010-01-01

    Experiments with reaccelerated beams are an essential component of the science program of existing and future rare isotope beam facilities. NSCL is currently constructing ReA3, a reaccelerator for rare isotopes that have been produced by projectile fragmentation and in-flight fission and that have been thermalized in a gas stopper. The resulting low-energy beam will be brought to an Electron Beam Ion Source/Trap (EBIS/T) in order to obtain highly charged ions at an energy of 12 keV/u. This charge breeder is followed by a compact linear accelerator with a maximum beam energy of 3MeV/u for U-238 and higher energies for lighter isotopes. Next-generation rare isotope beam facilities like the Facility for Rare Isotope Beams FRIB, but also existing Isotope Separator On-line (ISOL) facilities are expected to provide rare-isotope beam rates in the order of 10(11) particles per second for reacceleration. At present the most promising scheme to efficiently start the reacceleration of these intense beams is the use of a...

  4. The high-spin {sup 178m2}Hf isomer: production, chemical and isotopic separations, gamma spectrometry and internal conversion electrons spectrometry; L`isomere de haut spin {sup 178m2}Hf: production, separations chimiques et isotopiques, spectrometrie gamma et spectrometrie d`electrons de conversion interne

    Energy Technology Data Exchange (ETDEWEB)

    Kim, J.B.

    1993-10-13

    The high-spin isometric state of the nucleus 178Hf is a challenge for new and exotic nuclear physics studies. With its long half-life of 31 years, the production of a reasonable micro-weight quantity, with an isometric to ground state ratio as high as 5 per cent, is now regularly performed by intensive irradiations of ytterbium targets with helium ions of 36 MeV. Using sur-enriched, at 99,998 per cent, ytterbium 176 that we have prepared at the PARIS mass separator, the isomer purity has been improved. Targets of such material but also of enriched stable isotopes of hafnium have been prepared by electro-spraying of methanolic and acetic solutions. By inelastic diffusion of protons and deuton on these targets, the energy of the first state of the rotation band built on the isomer has been measured. Isotopic separations of the isomer have been performed, with a yield greater than 20 per cent, by the use of isotopically pure hafnium 176 as carrier. The separated beam of the mass 178 allowed to record the complete hyperfine spectrum of the isomer and to measure, for the first time, the magnetic dipole moment and the electric quadrupole moment. Isomer targets, implanted in various materials like copper, iron and hafnium monocrystal, provide the opportunity to accurately measure gamma and internal conversion decay of this nuclei and so to precise the multipolarity mixing of all transitions from K=16{sup +} to K=8{sup -}. (author). 49 refs., 47 figs., 11 tabs.

  5. Escapist Motives for On-line Gaming and Strengthening of Weak Ties

    DEFF Research Database (Denmark)

    Sudzina, Frantisek; Razmerita, Liana

    Due to advances of technology including faster and ubiquitously ac-cessible Internet connection, on-line gaming have grown tremendously in the last couple of years. The aim of this paper is to investigate whether escapist mo-tives for playing games are linked to strengthening of weak ties through...... on-line gaming. The research investigates Facebook and other on-line games separate-ly. A surprising result is that while most of the investigated escapist motives are positively correlated with strengthening of weak ties, the mundane breaking motive is negatively correlated with strengthening...

  6. Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Paducah Gaseous Diffusion Plant site

    Energy Technology Data Exchange (ETDEWEB)

    Marmer, G.J.; Dunn, C.P.; Moeller, K.L.; Pfingston, J.M.; Policastro, A.J.; Yuen, C.R.; Cleland, J.H. (ed.)

    1991-09-01

    Uranium enrichment in the United States has utilized a diffusion process to preferentially enrich the U-235 isotope in the uranium product. The U-AVLIS process is based on electrostatic extraction of photoionized U-235 atoms from an atomic vapor stream created by electron-beam vaporization of uranium metal alloy. The U-235 atoms are ionized when precisely tuned laser light -- of appropriate power, spectral, and temporal characteristics -- illuminates the uranium vapor and selectively photoionizes the U-235 isotope. A programmatic document for use in screening DOE site to locate a U-AVLIS production plant was developed and implemented in two parts. The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. These sites were subjected to a more rigorous and detailed comparative analysis for the purpose of developing a short list of reasonable alternative sites for later environmental examination. This environmental site description (ESD) provides a detailed description of the PGDP site and vicinity suitable for use in an environmental impact statement (EIS). The report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during a site visit. 65 refs., 15 tabs.

  7. SHyPIE: a new source for on-line production of multicharged radioactive condensable ion beams

    Energy Technology Data Exchange (ETDEWEB)

    Lecesne, N.; Foury, P.; Gaubert, G.; Huguet, Y.; Jardin, P.; Leroy, R.; Lewitowicz, M.; Marry, C.; Maunoury, L.; Pacquet, J.Y.; Robert, E.; Saint-Laurent, M.G.; Seron, D.; Sortais, P.; Villari, A.C.C. [Grand Accelerateur National d' Ions Lourds (GANIL), 14 - Caen (France); Angelique, J.C.; Orr, N.A. [Laboratoire de Physique Corpusculaire (CNRS/IN2P3), ISMRA, 14 - Caen (France); Blank, B. [CENBG, Centre d' Etudes Nucleaires de Bordeaux Gradignan, 33 (France); Clapier, F.; Ducourtieux, M.; Kandri-Rody, S.; Obert, J.; Pauwels, N.; Proust, J.; Putaux, J.C. [Institut de Physique Nucleaire, (IN2P3/CNRS) 91 - Orsay (France); Lepine, A. [IFUSP, C.P., Sao Paulo (Brazil)

    1999-07-01

    In order to define the future intensity and reliability of the on line radioactive beams for the SPIRAL project, an intense activity of research and development is being done around the target and the ion source problems. The main instrument for this purpose is the isotopic separator SIRa (Separateur d'Ions Radioactifs) installed in the D2 experimental cave at GANIL. One of the research axis is the production of multicharged radioactive condensable ions. In this aim, we have built a new compact ECR ion source, SHyPIE (Source Hybride pour la Production d'Ions Exotiques), whose original magnetic configuration is under patent since 1997. This new magnetic structure allows to place an internal production target very close to the plasma, while avoiding radiation damages of the sensitive permanent magnets. A series of on line experiments have been done, using SHyPIE with several internal target systems, and around thirty species of condensable and noble gases radioactive multicharged ion beams have been produced. The behaviour of the plasma in a close geometry with the production target has been studied. (authors)

  8. Status and future plan of KUR-ISOL for new isotope search

    Energy Technology Data Exchange (ETDEWEB)

    Taniguchi, Akihiro [Kyoto Univ., Kumatori, Osaka (Japan). Research Reactor Inst.

    1997-07-01

    He gas-jet type ISOL (KUR-ISOL: Kyoto University Reactor-Isotope Separator On-Line) was set up in Kyoto University Reactor in 1979. The thema of researches using KUR-ISOL are investigation of new isotope elements, study of nuclear structure of neutron-enrich nucleide in the neighborhood of 150 of mass number, development of unstable nuclide production unit and research of physical properties using unstable nuclide as probe. By KUR-ISOL, four kinds of new isotopes such as {sup 156}Pm, {sup 155}Nd, {sup 154}Pr and {sup 152}Ce and {beta}-decay of {sup 150}La had been identified. {beta}-decay of {sup 150}La as a sample of them was explained in this report. Today, the experiment of {sup 153}Pr, {sup 152}Pr and {sup 149,150}Ce are proceeding. For future plans, new beam line and new target used transuranic elements will be developed. (S.Y.)

  9. Stable isotope production with laser techniques; Production d`isotopes stables a l`aide des techniques laser

    Energy Technology Data Exchange (ETDEWEB)

    Petit, A. [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France). Dept. des Procedes d`Enrichissement

    1994-12-31

    Laser properties may be used for stable isotope production either by selective photoionization of an atom particular isotope, either by selective photodissociation of a molecule. Principles of both processes are reviewed and examples of calcium 43 isotope separation through photoionization and of carbon and oxygen isotope separation by photodissociation are presented. 4 figs., 1 tab., 11 refs.

  10. On-line generalized Steiner problem

    Energy Technology Data Exchange (ETDEWEB)

    Awerbuch, B.; Azar, Y.; Bartal, Y. [Tel Aviv Univ. (Israel)

    1996-12-31

    The Generalized Steiner Problem (GSP) is defined as follows. We are given a graph with non-negative weights and a set of pairs of vertices. The algorithm has to construct minimum weight subgraph such that the two nodes of each pair are connected by a path. We consider the on-line generalized Steiner problem, in which pairs of vertices arrive on-line and are needed to be connected immediately. We give a simple O(log{sup 2} n) competitive deterministic on-line algorithm. The previous best online algorithm (by Westbrook and Yan) was O({radical}n log n) competitive. We also consider the network connectivity leasing problem which is a generalization of the GSP. Here edges of the graph can be either bought or leased for different costs. We provide simple randomized O(log{sup 2} n) competitive algorithm based on the on-line generalized Steiner problem result.

  11. The war against on-line piracy

    OpenAIRE

    Harris, Julian

    2011-01-01

    A summary by Julian Harris, Deputy General Editor Amicus Curiae, of US attempts to control what it identifies as rogue Internet sites engaged in on-line piracy and opposition to such legislative moves.

  12. On-Line Acquisitions by LOLITA

    Directory of Open Access Journals (Sweden)

    Frances G. Spigai

    1970-12-01

    Full Text Available The on-line acquisition program (LOLITA in use at the Oregon State University Library is described in terms of development costs, equipment requirements, and overall design philosophy. In particular, the record format and content of records in the on-order file, and the on-line processing of these records (input, search, correction, output using a cathode ray tube display terminal are detailed.

  13. ACSEPP On-Line Electronic Payment Protocol

    Institute of Scientific and Technical Information of China (English)

    WANG Shao-bin; ZHU Xian; HONG Fan

    2004-01-01

    With analyzing the existing on-line electronic payment protocols, this paper presents a new on-line electronic payment protocol named ACSEPP: Anonymous, Convenient and Secure Electronic Payment Protocol.Its aim is to design a practical electronic payment protocol which is both secure and convenient.Without using PKI_CA frame, it realized the anonymity of consumer and merchant, the convenient of handling, the low cost of maintenance and the security.

  14. A versatile apparatus for on-line emission channeling experiments

    CERN Document Server

    da Silva, Manuel Ribeiro; Correia, João Guilherme; Amorim, Lígia Marina; Pereira, Lino Miguel da Costa

    2013-01-01

    The concept and functionality of an apparatus dedicated to emission channeling experiments using short-lived isotopes on-line at ISOLDE/CERN is described. The setup is assembled in two functional blocks - (a) base stand including beam collimation, implantation and measurement chamber, cryogenic extension, and vacuum control system and - (b) Panmure goniometer extension including maneuvering cradle and sample heating furnace. This setup allows for in situ implantation and sample analysis in the as-implanted state and upon cooling down to 50 K and during annealing up to 1200 K. The functionality of the setup will be illustrated with the example of establishing the lattice location of $^{56}$Mn probes implanted into GaAs.

  15. Equilibrium Modeling for Hydrogen Isotope Separation by Cryogenic Adsorption%氢同位素低温吸附分离的平衡吸附模型

    Institute of Scientific and Technical Information of China (English)

    张东辉; 周理; 苏伟; 孙艳

    2006-01-01

    The separation of hydrogen and deuterium by cryogenic adsorption was conducted, using the molecular sieve 5A as adsorbent, helium as the carrier gas in a fixed column. The breakthrough curves of hydrogen, deuterium and the mixture of two components in helium carrier gas were measured, a separation factor, approximately 2, for the hydrogen-deuterium binary mixture was obtained. The equilibrium model was built for simulation of the concentration distribution for single hydrogen, deuterium and their mixture with helium carrier in the fixed column, and the simulation compared well with the experimental results.

  16. Detection of outliers by neural network on the gas centrifuge experimental data of isotopic separation process; Aplicacao de redes neurais para deteccao de erros grosseiros em dados de processo de separacao de isotopos de uranio por ultracentrifugacao

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Monica de Carvalho Vasconcelos

    2004-07-01

    This work presents and discusses the neural network technique aiming at the detection of outliers on a set of gas centrifuge isotope separation experimental data. In order to evaluate the application of this new technique, the result obtained of the detection is compared to the result of the statistical analysis combined with the cluster analysis. This method for the detection of outliers presents a considerable potential in the field of data analysis and it is at the same time easier and faster to use and requests very less knowledge of the physics involved in the process. This work established a procedure for detecting experiments which are suspect to contain gross errors inside a data set where the usual techniques for identification of these errors cannot be applied or its use/demands an excessively long work. (author)

  17. Unusual isotopic composition of C-CO2 from sterilized soil microcosms: a new way to separate intracellular from extracellular respiratory metabolisms.

    Science.gov (United States)

    Kéraval, Benoit; Alvarez, Gaël; Lehours, Anne Catherine; Amblard, Christian; Fontaine, Sebastien

    2015-04-01

    intact cells were observed by microscopy. These "ghost" cells were completely destroyed by the irradiation-autoclaving combination releasing large amount of soluble C. The soil respiration (O2 consumption and CO2 production) was reduced by irradiation and autoclaving but not stopped, suggesting the presence of an EXOMET. The delta 13C of CO2 released in the irradiated-autoclaved soil was strongly depleted (-70‰) indicating that this extracellular metabolism induced a substantial isotopic fractionation. Our findings suggest that two main oxidative metabolisms co-occur in soils: cell respiration and EXOMET. The isotopic fractionation induced by the EXOMET open perspectives for its quantification in non-sterilized living soils.

  18. Nuclear moments and differences in mean square charge radii of short-lived neon isotopes by collinear laser spectroscopy

    CERN Document Server

    Geithner, R W

    2002-01-01

    The nuclear moments and charge radii of short-lived neon isotopes were measured by the use of collinear laser spectroscopy at the on-line mass separator ISOLDE at CERN. After a general introduction the semiclassical theory of atomic spectra is given and the relevant properties are calculated for neon. The atomic physics section is followed by a description of the experimental setup of the collinear laser spectroscopy experiment at ISOLDE. From the mass separator an isotopically clean ion beam with a kinetic energy of 60 keV is delivered to the experiments. In collinear laser spectroscopy the incoming ion beam from the mass separator is superimposed to a single frequency cw laser beam. The frequency of the atomic transition $\

  19. 减压精馏分离稳定同位素18O的模拟优化研究%Simulation and Optimization of Stable Isotope 18O Separation by Water Vacuum Distillation

    Institute of Scientific and Technical Information of China (English)

    陈玉岩; 秦川江; 肖斌; 徐静安

    2012-01-01

    研究建立了1座采用蒸馏水减压精馏分离稳定同位素18O的实验装置,其填料层高20 m,塔径为0.1m,塔内装填自主开发的PAC-18O专用填料.首先利用Aspen Plus建立模型并验证其可靠性,然后利用此模型得出1组模拟数据,并利用人工神经网络(ANN)及Statistica软件对这组模拟数据进行优化设计.综合分析了塔顶压力及产品采出量对18O产品丰度的影响.结果表明,产品18O的丰度随塔顶压力和产品采出量的降低而升高,并得出最优化的塔压及18O丰度与产品采出量间的数学关联式.本研究采用的模拟优化方法可应用到18O的产业化设计及推广至传统精馏过程的优化设计中.%In the research, a stable isotope 18O separation column was set up by water vacuum distillation with 20 m packing height and 0. 1 m diameter of the column. The self-developed special packing named PAC-18O was packed inside the column. Firstly, a model was created by using the Aspen Plus software, and then the simulation results were validated by test results. Secondly, a group of simulation results were created by Aspen Plus, and the optimal operation conditions were gotten by using the artificial neural network (ANN) and Statistica software. Considering comprehensive factors drawn from column pressure and from withdrawing velocity, conclusions were reached on the study of the impact on the abundance of the isotope I8O. The final results show that the abundance of the isotope 18O increases as column pressure dropping and withdrawing velocity decreasing. Besides, the optimal column pressure and the incidence formula between the abundance of the isotope 18O and withdrawing velocity were gotten. The conclusion is that the method of simulation and optimization can be applied to 18O industrial design and will be popular in traditional distillation process to realize optimization design.

  20. Formación on line

    Directory of Open Access Journals (Sweden)

    O. Grau-Perejoan

    Full Text Available La formación on line es una modalidad de enseñanza a distancia basada en las nuevas tecnologías. En este artículo se pretende hacer una introducción a base de describir a grandes rasgos sus características principales: asincronía, no presencialidad, comunicación escrita, función del profesor on line, así como los retos, los riesgos, las ventajas y los inconvenientes que plantea. Se exponen las diferencias entre la formación on line y la formación presencial, de manera que los docentes puedan adaptar de la mejor manera posible sus propuestas formativas a la modalidad on line. Se introduce el importantísimo papel de la planificación y de la fase de diseño y, finalmente, se repasan conceptos útiles para comprender mejor el mundo de la formación on line como son los conceptos entorno virtual de aprendizaje (EVA o Blended Learning (B-Learning.

  1. Titanium carbide-carbon porous nanocomposite materials for radioactive ion beam production: processing, sintering and isotope release properties

    CERN Document Server

    AUTHOR|(CDS)2081922; Stora, Thierry

    2017-01-26

    The Isotope Separator OnLine (ISOL) technique is used at the ISOLDE - Isotope Separator OnLine DEvice facility at CERN, to produce radioactive ion beams for physics research. At CERN protons are accelerated to 1.4 GeV and made to collide with one of two targets located at ISOLDE facility. When the protons collide with the target material, nuclear reactions produce isotopes which are thermalized in the bulk of the target material grains. During irradiation the target is kept at high temperatures (up to 2300 °C) to promote diffusion and effusion of the produced isotopes into an ion source, to produce a radioactive ion beam. Ti-foils targets are currently used at ISOLDE to deliver beams of K, Ca and Sc, however they are operated at temperatures close to their melting point which brings target degradation, through sintering and/or melting which reduces the beam intensities over time. For the past 10 years, nanostructured target materials have been developed and have shown improved release rates of the produced i...

  2. On line routing per mobile phone

    DEFF Research Database (Denmark)

    Bieding, Thomas; Görtz, Simon; Klose, Andreas

    2009-01-01

    . Additionally it is of utmost importance that the employed communication system is suitable integrated with the firm’s enterprise application system and business processes. On basis of a case study, we describe in this paper a system that is cheap and easy to implement due to the use of simple mobile phones......On-line routing is concerned with building vehicle routes in an ongoing fashion in such a way that customer requests arriving dynamically in time are efficiently and effectively served. An indispensable prerequisite for applying on-line routing methods is mobile communication technology...

  3. Educational On-Line Gaming Propensity

    DEFF Research Database (Denmark)

    Sudzina, Frantisek; Razmerita, Liana; Kirchner, Kathrin

    2014-01-01

    Educational on-line games are promising for new generations of students who are grown up digital. Th e new generations of students are technology savvy and spend lots of time on the web and on social networks. Based on an exploratory study, this article investigates the factors that infl uence...... students’ willingness to participate in serious games for teaching/learning. Th is study investigates the relationship between students’ behavior on Facebook, Facebook games, and their attitude toward educational on-line games. Th e results of the study reveal that the early adopters of educational games...

  4. The new on-line Czech Food Composition Database.

    Science.gov (United States)

    Machackova, Marie; Holasova, Marie; Maskova, Eva

    2013-10-01

    The new on-line Czech Food Composition Database (FCDB) was launched on http://www.czfcdb.cz in December 2010 as a main freely available channel for dissemination of Czech food composition data. The application is based on a complied FCDB documented according to the EuroFIR standardised procedure for full value documentation and indexing of foods by the LanguaL™ Thesaurus. A content management system was implemented for administration of the website and performing data export (comma-separated values or EuroFIR XML transport package formats) by a compiler. Reference/s are provided for each published value with linking to available freely accessible on-line sources of data (e.g. full texts, EuroFIR Document Repository, on-line national FCDBs). LanguaL™ codes are displayed within each food record as searchable keywords of the database. A photo (or a photo gallery) is used as a visual descriptor of a food item. The application is searchable on foods, components, food groups, alphabet and a multi-field advanced search. Copyright © 2013 Elsevier Ltd. All rights reserved.

  5. DEVELOPMENT OF AN ON-LINE COAL WASHABILITY ANALYZER

    Energy Technology Data Exchange (ETDEWEB)

    J.D. Miller; C.L. Lin; G.H. Luttrell; G.T. Adel; Barbara Marin

    2001-06-26

    Washability analysis is the basis for nearly all coal preparation plant separations. Unfortunately, there are no on- line techniques for determining this most fundamental of all coal cleaning information. In light of recent successes at the University of Utah, it now appears possible to determine coal washability on-line through the use of x-ray computed tomography (CT) analysis. The successful development of such a device is critical to the establishment of process control and automated coal blending systems. In this regard, Virginia Tech, Terra Tek Inc., and U.S. coal producers have joined with the University of Utah and to undertake the development of an X-ray CT-based on- line coal washability analyzer with financial assistance from DOE. Each project participant brought special expertise to the project in order to create a new dimension in coal cleaning technology. The project involves development of appropriate software and extensive testing/evaluation of well-characterized coal samples from operating coal preparation plants. Data collected to date suggest that this new technology is capable of serving as a universal analyzer that can not only provide washability analysis, but also particle size distribution analysis, ash analysis, and perhaps pyritic sulfur analysis.

  6. DEVELOPMENT OF AN ON-LINE COAL WASHABILITY ANALYZER

    Energy Technology Data Exchange (ETDEWEB)

    J.D. Miller

    1999-09-30

    Washability analysis is the basis for nearly all coal preparation plant separations. Unfortunately, there are no on-line techniques for determining this most fundamental of all coal cleaning information. In light of recent successes at the University of Utah, it now appears possible to determine coal washability on-line through the use of x-ray computed tomography (CT) analysis. The successful development of such a device is critical to the establishment of process control and automated coal blending systems. In this regard, Virginia Tech, Terra Tek Inc., and several eastern coal companies have joined with the University of Utah and agreed to undertake the development of a x-ray CT-based on-line coal washability analyzer with financial assistance from DOE. The three-year project will cost $594,571, of which 33% ($194,575) will be cost-shared by the participants. The project involves development of appropriate software and extensive testing/evaluation of well-characterized coal samples from operating coal preparation plants. Each project participant brings special expertise to the project which is expected to create a new dimension in coal cleaning technology. Finally, it should be noted that the analyzer may prove to be a universal analyzer capable of providing not only washability analysis, but also particle size distribution analysis, ash analysis and perhaps pyritic sulfur analysis.

  7. Development of a radiochemical separation for selenium with the aim of measuring its isotope 79 in low and intermediate nuclear wastes by ICP-MS.

    Science.gov (United States)

    Aguerre, Sandrine; Frechou, Carole

    2006-05-15

    Selenium (Se) 79 is a beta emitter produced from (235)U fission thus occurring as one of the fission products found in nuclear reactors. Due to its long half life (about 10(5) years), (79)Se is one of the radionuclides of interest for the performance of assessment studies of waste storage or disposal. Thus, the National Radioactive Waste Management Agency (Andra, France) requests its monitoring in wastes packages before their disposal in specific sites. Measurement of (79)Se is difficult owing to its trace level concentration and its low activity in nuclear wastes. A radiochemical procedure has to be carried out in order to separate selenium from the matrix and to concentrate it before the measurement with a mass spectrometric or a nuclear technique. The beginning of the development is presented in this paper. The optimised protocol firstly developed in view of an ICP-MS measurement, includes five steps based on microwave digestion, evaporation and separations on ion exchange resins. It was tested first on synthetic solutions and was optimised in order to be applicable to a large number of sample types. The recoveries of the whole procedure were evaluated using natural (82)Se or the gamma emitter (75)Se as a radioactive spiker. Then, the protocol was applied to two solid samples spiked with natural selenium, a glass microfiber filter and an ion exchange resin, and two liquid samples spiked with (75)Se, a synthetic solution and an effluent. The yields obtained for both samples ranged from 70 up to 80%.

  8. Dry phase reactor for generating medical isotopes

    Science.gov (United States)

    Mackie, Thomas Rockwell; Heltemes, Thad Alexander

    2016-05-03

    An apparatus for generating medical isotopes provides for the irradiation of dry-phase, granular uranium compounds which are then dissolved in a solvent for separation of the medical isotope from the irradiated compound. Once the medical isotope is removed, the dissolved compound may be reconstituted in dry granular form for repeated irradiation.

  9. 人牙齿中锶的特效树脂分离及其同位素测定%Separation and Isotopic Measurement of Sr in Tooth Samples Using Selective Specific Resins

    Institute of Scientific and Technical Information of China (English)

    贺茂勇; 逯海; 金章东; 王军

    2012-01-01

    采用锶特效树脂(Sr-Spec)建立了快速分离富集人牙齿中微量元素锶,并测定87Sr/86 Sr的有效方法.采用HNO3 -HClO4体系消解牙齿样品,以8 mol/L HNO3为介质上柱,8 mol/L HNO3淋洗,0.05 mol/L HNO3洗脱,收集淋洗液,蒸干;采用正热电离质谱法进行87Sr/86Sr的测定.结果表明,利用Sr-Spec树脂,不仅能将锶与基质中大量钙分离,并能有效分离同位素测定中干扰元素铷,本方法可以缩短分离时间,提高分离效率,减少试剂用量,降低实验空白.采用本方法对陕南地区人牙齿牙釉质中锶进行分离,测得的87Sr/86Sr值在0.710948~0.711037之间.%Strontium isotope of ancient human teeth provides an important scientific basis for ancient population migration, and Palaeodietary analysis. A fast and effective method for separation, precon-centration and isotopic determination of strontium with low content and rich calcium of tooth samples by Sr-Spec selective specific resin was established. The samples were completed dissolved with mixed acid of HNO3-HCIO4. Sr was increasingly well retained by Sr resin for mobile phases with nitric acid concentrations of 8 mol/L, However, potential interferences, like Ca, Rb will elute within the 8 mol/L nitric acid. Once adsorped, Sr can be eluted from the column by changing the mobile phase to weak nitric acid of 0. 05 mol/L. In comparison with the conventional separation procedures, the method has the advantages of fewer steps of separation, less usage of elution solutions and lower reagent blanks. The proposed method was used for the determination of 10 none carious teeth of enamel collected in southern of shaanxi. Giving values of 87Sr/86Sr were in the range of 0. 710948~0. 711037.

  10. ON-LINE DOCUMENTS CONTENT MANAGEMENT

    Directory of Open Access Journals (Sweden)

    VASILESCU RAMONA VIOLETA

    2010-05-01

    Full Text Available This paper outlines the steps and technologies used in developing an on-line application server with many desktop clients, and with high power processing for a wide range of input documents to obtain searchable documents on the highest portability standards, PDF and PDF /A.

  11. Rapid chemical separations

    CERN Document Server

    Trautmann, N

    1976-01-01

    A survey is given on the progress of fast chemical separation procedures during the last few years. Fast, discontinuous separation techniques are illustrated by a procedure for niobium. The use of such techniques for the chemical characterization of the heaviest known elements is described. Other rapid separation methods from aqueous solutions are summarized. The application of the high speed liquid chromatography to the separation of chemically similar elements is outlined. The use of the gas jet recoil transport method for nuclear reaction products and its combination with a continuous solvent extraction technique and with a thermochromatographic separation is presented. Different separation methods in the gas phase are briefly discussed and the attachment of a thermochromatographic technique to an on-line mass separator is shown. (45 refs).

  12. On-line Identification of the DC motor Parameters by using Least Mean Square Recursive Method

    Directory of Open Access Journals (Sweden)

    Marian Gaiceanu

    2014-09-01

    Full Text Available The on-line least square parameters (electrical and mechanical identification method of the separately DC motor is presented in this paper. The parameters of the DC machine are time dependent; therefore, for the DC drive control the on-line parameters identification procedure is mandatory. By knowing accurately the DC motor parameters, the parameters of the DC speed and current cascade controllers can be obtained.

  13. Escapist Motives for On-line Gaming and Strengthening of Weak Ties

    DEFF Research Database (Denmark)

    Sudzina, Frantisek; Razmerita, Liana

    Due to advances of technology including faster and ubiquitously accessible Internet connection, on-line gaming have grown tremendously in the last couple of years. The aim of this paper is to investigate whether escapist motives for playing games are linked to strengthening of weak ties through on......-line gaming. The research investigates Facebook and other on-line games separately. A surprising result is that while most of the investigated escapist motives are positively correlated with strengthening of weak ties, the mundane breaking motive is negatively correlated with strengthening of weak ties....

  14. Time of flight assisted ΔE - E method for enhanced isotope separation capabilities in heavy ion elastic recoil detection analysis

    Science.gov (United States)

    Eschbaumer, S.; Bergmaier, A.; Seiler, D.; Dollinger, G.

    2017-09-01

    The time of flight energy (TOF-E) setup installed at the scattering chamber of the Q3D magnetic spectrograph to perform heavy ion elastic recoil detection (ERD) analysis at the 14 MV Munich Tandem Accelerator has recently been upgraded. Now, the energy detector of the TOF-E setup is additionally capable of performing ΔE - E measurements for high energy recoil ions obtained from e.g. a 170 MeV 127 I projectile beam. Time of flight information is simultaneously acquired with the ΔE - E data for each detected ion. The combination of the TOF-E and the ΔE - E data gives the opportunity to set effective filter conditions to select for both, the elemental and the mass of the detected ion. As an example a boron doped carbon layer is analyzed and 10B and 11B is separated with the help of the combination of both methods.

  15. On-line solid phase extraction using the Prospekt-2 coupled with a liquid chromatography/tandem mass spectrometer for the determination of dextromethorphan, dextrorphan and guaifenesin in human plasma.

    Science.gov (United States)

    Kuhlenbeck, Debbie L; Eichold, Thomas H; Hoke, Steven H; Baker, Timothy R; Mensen, Robert; Wehmeyer, Kenneth R

    2005-01-01

    An on-line liquid chromatography/tandem mass spectrometry (LC-MS/MS) procedure, using the Prospekt- 2 system, was developed and used for the determination of the levels of the active ingredients of cough/cold medications in human plasma matrix. The experimental configuration allows direct plasma injection by performing on- line solid phase extraction (SPE) on small cartridge columns prior to elution of the analyte(s) onto the analytical column and subsequent MS/MS detection. The quantitative analysis of three analytes with differing polarities, dextromethorphan (DEX), dextrorphan (DET) and guaifenesin (GG) in human plasma presented a significant challenge. Using stable-isotope-labeled internal standards for each analyte, the Prospekt-2 on-line methodology was evaluated for sensitivity, suppression, accuracy, precision, linearity, analyst time, analysis time, cost, carryover and ease of use. The lower limit of quantitation for the on-line SPE procedure for DEX, DET and GG was 0.05, 0.05 and 5.0 ng mL(-1), respectively, using a 0.1 mL sample volume. The linear range for DEX and DET was 0.05-50 ng mL(-1) and was 5-5,000 ng mL(-1) for GG. Accuracy and precision data for five different levels of QC samples were collected over three separate days. Accuracy ranged from 90% to 112% for all three analytes, while the precision, as measured by the %RSD, ranged from 1.5% to 16.0%

  16. High-accuracy mass determination of neutron-rich rubidium and strontiumiIsotopes

    CERN Document Server

    Raimbault-Hartmann, H; Beck, D; Bollen, G; De Saint-Simon, M; Kluge, H J; König, M; Moore, R B; Schwarz, S; Savard, G; Szerypo, J

    2002-01-01

    The penning-trap mass spectrometer ISOLTRAP, installed at the on-line isotope separator ISOLDE at CERN, has been used to measure atomic masses of $^{88,89,90m,91,92,93,94}$Rb and $^{91- 95}$Sr. Using a resolving power of R $\\!\\scriptstyle\\approx$1 million a mass accuracy of typically 10 keV was achieved for all nuclides. Discrepancies with older data are analyzed and discussed, leading to corrections to those data. Together with the present ISOLTRAP data these corrected data have been used in the general mass adjustment.

  17. Educational On-Line Gaming Propensity

    DEFF Research Database (Denmark)

    Sudzina, Frantisek; Razmerita, Liana; Kirchner, Kathrin

    2014-01-01

    Educational on-line games are promising for new generations of students who are grown up digital. Th e new generations of students are technology savvy and spend lots of time on the web and on social networks. Based on an exploratory study, this article investigates the factors that infl uence...... students’ willingness to participate in serious games for teaching/learning. Th is study investigates the relationship between students’ behavior on Facebook, Facebook games, and their attitude toward educational on-line games. Th e results of the study reveal that the early adopters of educational games...... are likely to be students, who are young, have only a few Facebook connections, who currently play Facebook game(s). Furthermore, the study emphasizes that there may be differences between students coming from various countries....

  18. Connecting to On-line Data

    Science.gov (United States)

    Eichhorn, G.; Astrophysics Datacenter Executive Committee (ADEC)

    2004-05-01

    The Astrophysics Datacenter Executive Committee (ADEC) is coordinating the development of a system to facilitate the linking to on-line data. This system has three components: 1. Unique dataset identifiers. 2. A verification system for identifiers. 3. Permanent links to on-line data sets. 1. The ADEC has agreed on a naming scheme for data sets that allows for the unique identification of any data set. The ADEC data centers will clearly mark their data with these identifiers to allow the generation of links to these data. 2. Each data center has a utility that can check whether a data set identifier is a valid identifier at that center. A central verifier allows third parties access to these individual verifiers through a single portal. 3. The central verifier also provides permanent links to data sets through a central link forwarding system. This makes it possible to move data sets between data centers while maintaining the permanent links. The ADEC plans to first use this system to implement the linking from the literature to on-line data in a collaboration with the AAS and the University of Chicago Press for the AAS journals.

  19. On-line determination of anions in pulp mills by capillary electrophoresis (CE); Tehdasoloissa tapahtuva anionien kapillaarielektroforeettinen on-line maeaeritys ja sen hyoedyntaeminen prosessivalvonnassa - MPKY 02

    Energy Technology Data Exchange (ETDEWEB)

    Kokkonen, R.; Holmberg, M.; Vainikka, V. [Finnish Pulp and Paper Research Institute, Espoo (Finland)

    1998-12-31

    The aim of the study was to set-up a process control system for on-line measurement of certain anions. Typical anions which forms precipitates in pulp and paper mills are oxalate, carbonate and sulphate. Thus it is important to develop a continuous process analyzing system to control concentration levels of this anions. For the preliminary tests of continuous determinations of chloride and sulphate anions in tap water a simple on-line system was build in KCL (The Finnish Pulp and Paper Research Institute) and connected to a capillary electroforesis apparatus. In the preliminary tests a chromate buffer (ph = 7.6) was used. Separation of chloride and sulphate was excellent but the stability of buffer was not good enough and it was usable only for few hours. After experimental studies VTT developed a stable capillary electrophoresis method based on mixed amine buffer and this was selected for an on-line method for determination of anions in process waters of the pulp and paper industry. In the preliminary on-line test (r = 20) repeatabilities of migration times of sulphate and chloride with the chromate buffer were < 5 % (RSD) and peak heights < 15 % (RSD). With the mixed amine buffer repeatabilities were better. The preliminary tests showed that it is possible to connect a capillary electrophoresis system to on-line measurements. For the moment no commercial on-line CE apparatus is available. (orig.)

  20. Beta-decay energies and masses of short-lived isotopes of rubidium, caesium, francium, and radium

    CERN Document Server

    Westgaard, L; Nyman, G H; Roeckl, E

    1975-01-01

    Total decay energies have been measured for a number of neutron- deficient Rb and Cs isotopes, as well as for some neutron-rich isotopes of Fr and Ra. Mass separated sources were produced at the ISOLDE on-line separator at CERN. By applying two different beta - gamma coincidence methods, Q values or their lower limits were determined for /sup 76-78/Rb, /sup 80/Rb, /sup 121-124/Cs, /sup 222 /Fr, /sup 224-226/Fr, /sup 229/Ra and /sup 229/Ac. For many of these nuclei, the atomic mass excesses could be derived, allowing the comparison of masses of far unstable nuclei with predictions from mass formulae. The odd-odd nuclei /sup 76/Rb and /sup 78/Rb appear to be 1-1/sup 1///sub 2/ MeV more strongly bound than expected from the systematics. (70 refs).

  1. Design of an EBIS charge breeder system for rare-isotope beams

    Science.gov (United States)

    Park, Young-Ho; Son, Hyock-Jun; Kim, Jongwon

    2016-09-01

    Rare-isotope beams will be produced by using the isotope separation on-line (ISOL) system at the Rare Isotope Science Project (RISP). A proton cyclotron is the driver accelerator for ISOL targets, and uranium carbide (UCx) will be a major target material. An isotope beam of interest extracted from the target will be ionized and selected by using a mass separator. The beam emittance will then be reduced by using a radio-frequency quadrupole (RFQ) cooler before the beam is injected into the electron-beam ion-source (EBIS) charge breeder (CB). The maximum electron beam current of the EBIS is 3 A from a cathode made of IrCe in an applied magnetic field of 0.2 T. The size of the electron beam is compressed by magnetic fields of up to 6 T caused in the charge-breeding region by a superconducting solenoid. The design of EBIS-CB was performed by using mechanics as well as beam optics. A test stand for the electron gun and its collector, which can take an electron-beam power of 20 kW, are under construction. The gun assembly was first tested by using a high-voltage pulse so as to measure its perveance. The design of the EBIS, along with its test stand, is described.

  2. Start-to-end simulation with rare isotope beam for post accelerator of the RAON accelerator

    CERN Document Server

    Jin, Hyunchang

    2016-01-01

    The RAON accelerator of the Rare Isotope Science Project (RISP) has been developed to create and accelerate various kinds of stable heavy ion beams and rare isotope beams for a wide range of the science applications. In the RAON accelerator, the rare isotope beams generated by the Isotope Separation On-Line (ISOL) system will be transported through the post accelerator, namely, from the post Low Energy Beam Transport (LEBT) system and the post Radio Frequency Quadrupole (RFQ) to the superconducting linac (SCL3). The accelerated beams will be put to use in the low energy experimental hall or accelerated again by the superconducting linac (SCL2) in order to be used in the high energy experimental hall. In this paper, we will describe the results of the start-to-end simulations with the rare isotope beams generated by the ISOL system in the post accelerator of the RAON accelerator. In addition, the error analysis and correction at the superconducting linac SCL3 will be presented.

  3. A Refreshable, On-line Cache for HST Data Retrieval

    Science.gov (United States)

    Fraquelli, Dorothy A.; Ellis, Tracy A.; Ridgaway, Michael; DPAS Team

    2016-01-01

    We discuss upgrades to the HST Data Processing System, with an emphasis on the changes Hubble Space Telescope (HST) Archive users will experience. In particular, data are now held on-line (in a cache) removing the need to reprocess the data every time they are requested from the Archive. OTFR (on the fly reprocessing) has been replaced by a reprocessing system, which runs in the background. Data in the cache are automatically placed in the reprocessing queue when updated calibration reference files are received or when an improved calibration algorithm is installed. Data in the on-line cache are expected to be the most up to date version. These changes were phased in throughout 2015 for all active instruments.The on-line cache was populated instrument by instrument over the course of 2015. As data were placed in the cache, the flag that triggers OTFR was reset so that OTFR no longer runs on these data. "Hybrid" requests to the Archive are handled transparently, with data not yet in the cache provided via OTFR and the remaining data provided from the cache. Users do not need to make separate requests.Users of the MAST Portal will be able to download data from the cache immediately. For data not in the cache, the Portal will send the user to the standard "Retrieval Options Page," allowing the user to direct the Archive to process and deliver the data.The classic MAST Search and Retrieval interface has the same look and feel as previously. Minor changes, unrelated to the cache, have been made to the format of the Retrieval Options Page.

  4. Target and PADC Track Detectors for Rare Isotope Studies

    Directory of Open Access Journals (Sweden)

    J. Bermudez

    2011-01-01

    Full Text Available A higher yield of rare isotope production methods, for example, isotope separation on-line (ISOL, is expected to be developed for the EURISOL facility. In this paper as a part of the ongoing project, high power-target assembly and passive detector inclusion are given. Theoretical calculations of several configurations were done using Monte Carlo code FLUKA aimed to produce 1015 fiss/s on LEU-Cx target. The proposed radioactive ion beam (RIB production relies on a high-power (4 MW multibody target; a complete target design is given. Additionally we explore the possibility to employ PADC passive detector as a complementary system for RIB characterization, since these already demonstrated their importance in nuclear interactions phenomenology. In fact, information and recording rare and complex reaction product or short-lived isotope detection is obtained in an integral form through latent track formation. Some technical details on track formation and PADC detector etching conditions complete this study.

  5. Total on-line purchasing system (TOPS)

    Energy Technology Data Exchange (ETDEWEB)

    Collins, N.

    1995-11-01

    The Information Management Division (IMD) at LLNL is developing a new purchasing system for the Procurement Department. The first major development of this new system is called, {open_quotes}Total On-Line Purchasing System{close_quotes} (TOPS). TOPS will help speed up the requisitioning process by having requisitions electronically entered by requesters and electronically sent to buyers to be put on Purchase Orders. The new purchasing system will use Electronic Commerce (EC)/Electronic Data Interchange (EDI), to help increase transaction flows for shipping notices, RFQs, Quotes, Purchase Orders, and Invoices. ANSI X.12 is the EDI standard that this new EC will use.

  6. Neutron-rich isotope production using a uranium carbide - carbon nanotubes SPES target prototype

    Science.gov (United States)

    Corradetti, S.; Biasetto, L.; Manzolaro, M.; Scarpa, D.; Carturan, S.; Andrighetto, A.; Prete, G.; Vasquez, J.; Zanonato, P.; Colombo, P.; Jost, C. U.; Stracener, D. W.

    2013-05-01

    The SPES (Selective Production of Exotic Species) project, under development at the Istituto Nazionale di Fisica Nucleare - Laboratori Nazionali di Legnaro (INFN-LNL), is a new-generation Isotope Separation On-Line (ISOL) facility for the production of radioactive ion beams by means of the proton-induced fission of uranium. In the framework of the research on the SPES target, seven uranium carbide discs, obtained by reacting uranium oxide with graphite and carbon nanotubes, were irradiated with protons at the Holifield Radioactive Ion Beam Facility (HRIBF) of Oak Ridge National Laboratory (ORNL). In the following, the yields of several fission products obtained during the experiment are presented and discussed. The experimental results are then compared to those obtained using a standard uranium carbide target. The reported data highlights the capability of the new type of SPES target to produce and release isotopes of interest for the nuclear physics community.

  7. Conceptual Design of Hydrogen Isotopes Chromatographic Separation System With Super Large Capacity%超大容量氢同位素色谱分离系统的概念设计

    Institute of Scientific and Technical Information of China (English)

    谢波; 翁葵平; 刘云怒; 侯建平

    2012-01-01

    A super largecapacity hydrogen isotopes separation system, including total plan, unit (including making and purification of gas, three-grade chromatographic columns, gas loop and auto-controll, and carrier recovery) and experimental scheme, had been designed on the basis of a series of hydrogen-deuterium experiments by temperature programmed de-sorption. The characteristic of the system was that desorption kinetic parameters could be directly calculated from the hydrogen isotope separation desorption spectra information. In other words, the complicated dynamic process of separation could be described by the desorption rate equation, shape parameter and desorption activation energy calculation on the condition of the experimental data and appropriate assumptions (equilibrium and adsorption, uniform surface). In previous work, an experimental series of operation to verify the successive enrichment of D2 from a H2-D2 mixture, the production of the deuterium from natural hydrogen and the recovery of tritium such as from the nuclear heavy-water were car-ried out using MS5A at 77 K. This work was only conceptual design, so it was necessary to identify the availability of super large capacity system by experiment.%在多年从事色谱分离氢同位素技术研究的基础上,设计了一套超大容量氢同位素分离系统,包括系统的总体设计,以配气及纯化、三级色谱柱、气体流路及自动控制和载气回收为主的单元设计,以及调试实验方案设计.该系统的特点是可以根据氢同位素分离解吸谱图的信息比较直接地计算出解吸过程的动力学参数,即在实验数据的支持和适当的假设条件(平衡再吸附、均匀表面)下,依靠解吸速率方程、形状参数和解吸活化能的计算便可比较系统地描述其复杂的动力学过程.在以前的工作中,虽然已经证实了采用5A分子筛柱在77 K的低温下,可以连续富集氢-氘混合气中的氘、天然氢中的氘,甚至含

  8. On-line and Mobil Learning Activities

    Science.gov (United States)

    Ackerman, S. A.; Whittaker, T. M.; Jasmin, T.; Mooney, M. E.

    2012-12-01

    Introductory college-level science courses for non-majors are critical gateways to imparting not only discipline-specific information, but also the basics of the scientific method and how science influences society. They are also indispensable for student success to degree. On-line, web-based homework (whether on computers or mobile devices) is a rapidly growing use of the Internet and is becoming a major component of instruction in science, replacing delayed feedback from a few major exams. Web delivery and grading of traditional textbook-type questions is equally effective as having students write them out for hand grading, as measured by student performance on conceptual and problem solving exams. During this presentation we will demonstrate some of the interactive on-line activities used to teach concepts and how scientists approach problem solving, and how these activities have impacted student learning. Evaluation of the activities, including formative and summative, will be discussed and provide evidence that these interactive activities significantly enhance understanding of introductory meteorological concepts in a college-level science course. More advanced interactive activities are also used in our courses for department majors, some of these will be discussed and demonstrated. Bring your mobile devices to play along! Here is an example on teaching contouring: http://profhorn.aos.wisc.edu/wxwise/contour/index.html

  9. The Monitor System for the LHCb on-line farm

    CERN Document Server

    Bonifazi, F; Carbone, A; Galli, D; Gregori, D; Marconi, U; Peco, G; Vagnoni, V

    2005-01-01

    The aim of the LHCb on-line farm Monitor System is to keep under control all the working indicators which are relevant for the farm operation, and to set the appropriate alarms whenever an error or a critical condition comes up. Since the most stressing tasks of the farm are the data transfer and processing, relevant indicators includes the CPU and the memory load of the system, the network interface and the TCP/IP stack parameters, the rates of the interrupts raised by the network interface card and the detailed status of the running processes. The monitoring of computers’ physical conditions (temperatures, fan speeds and motherboard voltages) are the subject of a separate technical note, since they are accessed in a different way, by using the IPMI protocol.

  10. On-line control of the nonlinear dynamics for synchrotrons

    Science.gov (United States)

    Bengtsson, J.; Martin, I. P. S.; Rowland, J. H.; Bartolini, R.

    2015-07-01

    We propose a simple approach to the on-line control of the nonlinear dynamics in storage rings, based on compensation of the nonlinear resonance driving terms using beam losses as the main indicator of the strength of a resonance. The correction scheme is built on the analysis of the resonance driving terms in first perturbative order and on the possibility of using independent power supplies in the sextupole magnets, which is nowadays present in many synchrotron light sources. Such freedom allows the definition of "smart sextupole knobs" attacking each resonance separately. The compensation scheme has been tested at the Diamond light source and proved to be effective in opening up the betatron tune space, resonance free, available to the electron beam and to improve the beam lifetime.

  11. FLOW INJECTION ON-LINE SEPARATION AND SPECTROPHOTOMETRIC DETERMINATION OF TRACES OF LEAD IN ENVIRONMENTAL SAMPLES%环境样品中痕量铅的流动注射在线分离及分光光度检测

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A flow injection method has been developed for the determination of lead in environmental samples by use of on-line preconcentration on a Pb*SpecTM column and spectrophotometric detection. The lead in sample solutions was adsorbed selectively on the column from 1mol*l-1 nitric acid and the retained lead was eluted with 0.1mol*l-1 ammonium oxalate.4-(2-pyridylazo)resorcinol (PAR) was used as a chromogenic reagent at pH 10 and the absorbance of Pb-PAR complex was monitored at 530 nm. The pumps, valves and spectrophotometer were controlled by a personal computer. The detection limit (3σ) was 3ng of lead. The RSD is 1.7% at a level of 0.4μg lead. The proposed method was successfully applied to the determination of lead in fly ash of an incinerator for industrial waste and in river water certified reference material provided by the Japan Society for Analytical Chemistry.

  12. The production of stable isotopes in Spain

    Energy Technology Data Exchange (ETDEWEB)

    Urgel, M.; Iglesias, J.; Casas, J.; Saviron, J. M.; Quintanilla, M.

    1965-07-01

    The activities developed in the field of the production of stable isotopes by means of ion-exchange chromatography and thermal diffusion techniques are reported. The first method was used to study the separation of the nitrogen and boron isotopes, whereby the separation factor was determined by the break through method. Values ranging from 1,028 to 1,022 were obtained for the separation factor of nitrogen by using ammonium hydroxide solutions while the corresponding values as obtained for boron amounted to 1,035-1,027 using boric acid solutions. Using ammonium chloride or acetate and sodium borate, respectively, resulted in the obtention of values for the separation factor approaching unity. The isotopic separation has been carried out according to the method of development by displacement. The separation of the isotopes of the noble gases, oxygen, nitrogen and carbon has been accomplished resorting to the method of thermal diffusion. (Author) 16 refs.

  13. On-Line Hyperspectral Transmittance Imaging for Internal Defect Detection of Pickling Cucumbers

    Science.gov (United States)

    Hyperspectral imaging technique under transmittance mode was investigated for detection of internal defect in pickling cucumbers such as carpel suture separation or hollow cucumbers caused by mechanical stress. A prototype of on-line hyperspectral transmittance imaging system was developed for real...

  14. On-Line Real Time Realization and Application of Adaptive Fuzzy Inference Neural Network

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In this paper,a modeling algorithm developed by transferring the adaptive fuzzy inference neural network into an on-line real time algorithm,combining the algorithm with conventional system identification method and applying them to separate identification of nonlinear mu Iti-variable systems is introduced and discussed.

  15. Aprender a innovar: una experiencia on line

    Directory of Open Access Journals (Sweden)

    Joaquín MORENO MARCHAL

    2014-11-01

    Full Text Available La creatividad y la innovación se han convertido en recursos clave en la denominada sociedad del conocimiento, que bien podría ser también llamada sociedad de la innovación. Pero innovar es una actividad compleja, que integra la aplicación de múltiples capacidades, el pensamiento divergente y convergente, la gestión de equipos humanos, la comunicación. Ahora bien, a innovar se puede, y se debe, aprender. Aprender a innovar es un reto y también una obligación para el conjunto del sistema educativo en todos sus niveles. Partiendo de estas consideraciones este trabajo expone una experiencia de aprendizaje de la creatividad y de la innovación a través de un curso totalmente on line basado en la plataforma MOODLE, en el marco del Programa de Formación Permanente de la Universidad de Cádiz. Se presenta un modelo del proceso de innovación, denominado CREALAB, de elaboración propia. Este modelo se ha utilizado como base del proceso de aprendizaje de la creatividad y de la innovación y en el diseño del curso, está organizado en torno a actividades y tiene un carácter iterativo y realimentado. Se presentan además el conjunto del diseño metodológico y los resultados obtenidos en las dos ediciones celebradas hasta el momento. El diseño del curso totalmente on line y los resultados alcanzados permiten estimar un alto potencial de aplicación, tanto a nivel personal como a nivel organizacional.

  16. On-line chemical composition analyzer development

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, M.J.; Garrison, A.A.; Muly, E.C.; Moore, C.F.

    1992-02-01

    The energy consumed in distillation processes in the United States represents nearly three percent of the total national energy consumption. If effective control of distillation columns can be accomplished, it has been estimated that it would result in a reduction in the national energy consumption of 0.3%. Real-time control based on mixture composition could achieve these savings. However, the major distillation processes represent diverse applications and at present there does not exist a proven on-line chemical composition sensor technology which can be used to control these diverse processes in real-time. This report presents a summary of the findings of the second phase of a three phase effort undertaken to develop an on-line real-time measurement and control system utilizing Raman spectroscopy. A prototype instrument system has been constructed utilizing a Perkin Elmer 1700 Spectrometer, a diode pumped YAG laser, two three axis positioning systems, a process sample cell land a personal computer. This system has been successfully tested using industrially supplied process samples to establish its performance. Also, continued application development was undertaken during this Phase of the program using both the spontaneous Raman and Surface-enhanced Raman modes of operation. The study was performed for the US Department of Energy, Office of Industrial Technologies, whose mission is to conduct cost-shared R D for new high-risk, high-payoff industrial energy conservation technologies. Although this document contains references to individual manufacturers and their products, the opinions expressed on the products reported do not necessarily reflect the position of the Department of Energy.

  17. Research Directed at Developing a Classical Theory to Describe Isotope Separation of Polyatomic Molecules Illuminated by Intense Infrared Radiation. Final Report for period May 7, 1979 to September 30, 1979; Extension December 31, 1997

    Science.gov (United States)

    Lamb, W. E. Jr.

    1981-12-01

    This final report describes research on the theory of isotope separation produced by the illumination of polyatomic molecules by intense infrared laser radiation. This process is investigated by treating the molecule, sulfur hexafluoride, as a system of seven classical particles that obey the Newtonian equations of motion. A minicomputer is used to integrate these differential equations. The particles are acted on by interatomic forces, and by the time-dependent electric field of the laser. We have a very satisfactory expression for the interaction of the laser and the molecule which is compatible with infrared absorption and spectroscopic data. The interatomic potential is capable of improvement, and progress on this problem is still being made. We have made several computer runs of the dynamical behavior of the molecule using a reasonably good model for the interatomic force law. For the laser parameters chosen, we find that typically the molecule passes quickly through the resonance region into the quasi-continuum and even well into the real continuum before dissociation actually occurs. When viewed on a display terminal, the motions are exceedingly complex. As an aid to the visualization of the process, we have made a number of 16 mm movies depicting a three-dimensional representation of the motion of the seven particles. These show even more clearly the enormous complexity of the motions, and make clear the desirability of finding ways of characterizing the motion in simple ways without giving all of the numerical detail. One of the ways to do this is to introduce statistical parameters such as a temperature associated with the distribution of kinetic energies of the single particle. We have made such an analysis of our data runs, and have found favorable indications that such methods will prove useful in keeping track of the dynamical histories.

  18. A Dynamic Simulation of Stable Isotope 13C Separation by Cryogenic Distillation%Aspen软件在低温精馏分离稳定同位素13C中的应用

    Institute of Scientific and Technical Information of China (English)

    许保云; 田叶盛; 李虎林; 龙磊; 吉永喆; 蔡扬; 李良君; 杜晓宁

    2012-01-01

    本工作对低温精馏分离13C同位素的稳态模拟与动态模拟进行了研究.使用商用流程模拟软件Aspen Plus建立低温精馏过程的稳态模型,通过对比模拟数据与实验数据,验证物性参数和模型的可靠性.使用Aspen Dynamics建立低温精馏过程的动态模型,动态模拟结果与实验数据吻合良好.结果表明,可以使用Aspen Dynamics对碳同位素分离过程进行动态特性研究,并对精馏过程进行开车时间预测、控制方案分析、操作性分析和安全性分析等.%The steady-state and dynamic process simulation of the cryogenic rectification process of isotope C-13 was researched. The commercial process simulation software Aspen Plus was used to establish the steady-state model of the cryogenic rectification process. The reliability of the model was validated by the comparison of the simulation result and the experimental data. It showed that the technological process design of high quality C-13 can be conducted with software Aspen Plus. The dynamic process model was built with software Aspen Dynamics. The simulation results with the models were well supported by experimental ones. It showed that the dynamic characters of the separation process can be investigated with Aspen Dynamics. Then, the dynamic start-up time, control scheme analysis, operability analysis, and safety analysis etc. Can be implemented with dynamic simulation.

  19. New Levels in 118pd Observed in theβ Decay of Very Neutron-Rich 118Rh Isotope

    Institute of Scientific and Technical Information of China (English)

    WANG You-Bao; K. Per(a)j(a)rvi; S. Rinta-Antila; J. Szerypo; J. C. Wang; J. (A)yst(o); P. Dendooven; J. Huikari; A. Jokinen; V. S. Kolhinen; G. Lhersonneau; A. Nieminen; S. Nummela; H. Penttil(a)

    2006-01-01

    @@ We investigate theβ decay of very neutron-rich 118Rh isotope using on-line mass-separated sources which are produced by applying 25 Me V proton induced symmetric fission of natural uranium at the IGISOL facility. The β-γ and γ-γ coincidence spectroscopy is employed to establish the level scheme of daughter nucleus 118 pd. Five low-lying new levels are identified for the first time with tentative spin and parity assignments based on the even-mass Pd systematics.

  20. Numerical solution of the Maxwell-Vlasov equations in the periodic regime. Application to the study of isotope separation by ion cyclotron resonance; Resolution numerique des equations de Maxwell-Vlasov en regime periodique. Application a l'etude de la separation isotopique par resonance cyclotron ionique

    Energy Technology Data Exchange (ETDEWEB)

    Omnes, P

    1999-01-25

    This work is dedicated to the study of the behaviour of a magnetic confined plasma that is excited by a purely sinusoidal electric current delivered by an antenna. The response of the electrons to the electromagnetic field is considered as linear,whereas the ions of the plasma are represented by a non-relativistic Vlasov equation. In order to avoid transients, the coupled Maxwell-Vlasov equations are solved in a periodic mode and in a bounded domain. An equivalent electric conductivity tensor has been defined, this tensor is a linear operator that links the electric current generated by the movement of the particles to the electromagnetic field. Theoretical considerations can assure the existence and uniqueness of a periodical solution to Vlasov equations and of a solution to Maxwell equations in harmonic mode. The system of equations is periodical and has been solved by using an iterative method. The application of this method to the simulation of a isotopic separation device based on ionic cyclotron resonance has shown that the convergence is reached in a few iterations and that the solution is valid. Furthermore a method based on a finite-volume formulation of Maxwell equations in the time domain is presented. 2 new variables are defined in order to better take into account the Gauss' law and the conservation of the magnetic flux, the new system is still hyperbolic. The parallelization of the process has been successfully realized. (A.C.)

  1. Influence of visualization on consumption during on-line shopping

    OpenAIRE

    Hictaler, Urška

    2013-01-01

    This diploma work studies the influence of visualization on consumption during on-line shopping. The first part of the thesis starts with key areas of visualization, consumption and on-line shopping. Visualization, areas of use, human perception and ways of product presentation in on-line shops are defined discussed first. Next, consumption, consumers and factors that influence their decisions and satisfaction are defined. The last topic in the first part of the thesis discusses on-line shopp...

  2. Compound Specific Hydrogen Isotope Composition of Type II and III Kerogen Extracted by Pyrolysis-GC-MS-IRMS

    Science.gov (United States)

    Socki, Richard A.; Pernia, Denet; Evans, Michael; Fu, Qi; Bissada, Kadry K.; Curiale, Joseph A.; Niles, Paul B.

    2013-01-01

    The use of Hydrogen (H) isotopes in understanding oil and gas resource plays is in its infancy. Described here is a technique for H isotope analysis of organic compounds pyrolyzed from oil and gas shale-derived kerogen. Application of this technique will progress our understanding. This work complements that of Pernia et al. (2013, this meeting) by providing a novel method for the H isotope analysis of specific compounds in the characterization of kerogen extracted by analytically diverse techniques. Hydrogen isotope analyses were carried out entirely "on-line" utilizing a CDS 5000 Pyroprobe connected to a Thermo Trace GC Ultra interfaced with a Thermo MAT 253 IRMS. Also, a split of GC-separated products was sent to a DSQ II quadrupole MS to make semi-quantitative compositional measurements of the extracted compounds. Kerogen samples from five different basins (type II and III) were dehydrated (heated to 80 C overnight in vacuum) and analyzed for their H isotope compositions by Pyrolysis-GC-MS-TC-IRMS. This technique takes pyrolysis products separated via GC and reacts them in a high temperature conversion furnace (1450 C) which quantitatively forms H2, following a modified method of Burgoyne and Hayes, (1998, Anal. Chem., 70, 5136-5141). Samples ranging from approximately 0.5 to 1.0mg in size, were pyrolyzed at 800 C for 30s. Compounds were separated on a Poraplot Q GC column. Hydrogen isotope data from all kerogen samples typically show enrichment in D from low to high molecular weight compounds. Water (H2O) average deltaD = -215.2 (V-SMOW), ranging from -271.8 for the Marcellus Shale to -51.9 for the Polish Shale. Higher molecular weight compounds like toluene (C7H8) have an average deltaD of -89.7 0/00, ranging from -156.0 for the Barnett Shale to -50.0 for the Monterey Shale. We interpret these data as representative of potential H isotope exchange between hydrocarbons and sediment pore water during formation within each basin. Since hydrocarbon H isotopes

  3. On-Line Learning: One Way to Bring People Together

    Science.gov (United States)

    Goff-Kfouri, Carol Ann

    2006-01-01

    The purpose of this study was to demonstrate the benefits of on-line learning for adult learners and to further demystify three common misconceptions concerning on-line learning: students certainly do receive support from their on-line professors, the professor is pro-active rather than passive, and students may be more motivated to learn than in…

  4. A Distributed System for Learning Programming On-Line

    Science.gov (United States)

    Verdu, Elena; Regueras, Luisa M.; Verdu, Maria J.; Leal, Jose P.; de Castro, Juan P.; Queiros, Ricardo

    2012-01-01

    Several Web-based on-line judges or on-line programming trainers have been developed in order to allow students to train their programming skills. However, their pedagogical functionalities in the learning of programming have not been clearly defined. EduJudge is a project which aims to integrate the "UVA On-line Judge", an existing…

  5. Leatherback Isotopes

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — SWFSC is currently working on a project identifying global marine isotopes using leatherback turtles (Dermochelys coriacea) as the indicator species. We currently...

  6. An integrated on-line irradiation and in situ live cell imaging system

    Science.gov (United States)

    Liang, Ying; Fu, Qibin; Wang, Weikang; Liu, Yu; Liu, Feng; Yang, Gen; Wang, Yugang

    2015-09-01

    Ionizing radiation poses a threat to genome integrity by introducing DNA damages, particularly DNA double-strand breaks (DSB) in cells. Understanding how cells react to DSB and maintain genome integrity is of major importance, since increasing evidences indicate the links of DSB with genome instability and cancer predispositions. However, tracking the dynamics of DNA damages and repair response to ionizing radiation in individual cell is difficult. Here we describe the development of an on-line irradiation and in situ live cell imaging system based on isotopic sources at Institute of Heavy Ion Physics, Peking University. The system was designed to irradiate cells and in situ observe the cellular responses to ionizing radiation in real time. On-line irradiation was achieved by mounting a metal framework that hold an isotopic γ source above the cell culture dish for γ irradiation; or by integrating an isotopic α source to an objective lens under the specialized cell culture dish for α irradiation. Live cell imaging was performed on a confocal microscope with an environmental chamber installed on the microscope stage. Culture conditions in the environment chamber such as CO2, O2 concentration as well as temperature are adjustable, which further extends the capacity of the system and allows more flexible experimental design. We demonstrate the use of this system by tracking the DSB foci formation and disappearance in individual cells after exposure to irradiation. On-line irradiation together with in situ live cell imaging in adjustable culture conditions, the system overall provides a powerful tool for investigation of cellular and subcellular response to ionizing radiation under different physiological conditions such as hyperthermia or hypoxia.

  7. An integrated on-line irradiation and in situ live cell imaging system

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Ying; Fu, Qibin; Wang, Weikang; Liu, Yu; Liu, Feng; Yang, Gen, E-mail: gen.yang@pku.edu.cn; Wang, Yugang

    2015-09-01

    Ionizing radiation poses a threat to genome integrity by introducing DNA damages, particularly DNA double-strand breaks (DSB) in cells. Understanding how cells react to DSB and maintain genome integrity is of major importance, since increasing evidences indicate the links of DSB with genome instability and cancer predispositions. However, tracking the dynamics of DNA damages and repair response to ionizing radiation in individual cell is difficult. Here we describe the development of an on-line irradiation and in situ live cell imaging system based on isotopic sources at Institute of Heavy Ion Physics, Peking University. The system was designed to irradiate cells and in situ observe the cellular responses to ionizing radiation in real time. On-line irradiation was achieved by mounting a metal framework that hold an isotopic γ source above the cell culture dish for γ irradiation; or by integrating an isotopic α source to an objective lens under the specialized cell culture dish for α irradiation. Live cell imaging was performed on a confocal microscope with an environmental chamber installed on the microscope stage. Culture conditions in the environment chamber such as CO{sub 2}, O{sub 2} concentration as well as temperature are adjustable, which further extends the capacity of the system and allows more flexible experimental design. We demonstrate the use of this system by tracking the DSB foci formation and disappearance in individual cells after exposure to irradiation. On-line irradiation together with in situ live cell imaging in adjustable culture conditions, the system overall provides a powerful tool for investigation of cellular and subcellular response to ionizing radiation under different physiological conditions such as hyperthermia or hypoxia.

  8. On-Line Impact Load Identification

    Directory of Open Access Journals (Sweden)

    Krzysztof Sekuła

    2013-01-01

    Full Text Available The so-called Adaptive Impact Absorption (AIA is a research area of safety engineering devoted to problems of shock absorption in various unpredictable scenarios of collisions. It makes use of smart technologies (systems equipped with sensors, controllable dissipaters and specialised tools for signal processing. Examples of engineering applications for AIA systems are protective road barriers, automotive bumpers or adaptive landing gears. One of the most challenging problems for AIA systems is on-line identification of impact loads, which is crucial for introducing the optimum real-time strategy of adaptive impact absorption. This paper presents the concept of an impactometer and develops the methodology able to perform real-time impact load identification. Considered dynamic excitation is generated by a mass M1 impacting with initial velocity V0. An analytical formulation of the problem, supported with numerical simulations and experimental verifications is presented. Two identification algorithms based on measured response of the impacted structure are proposed and discussed. Finally, a concept of the AIA device utilizing the idea of impactometer is briefly presented.

  9. SOL: INNOVACIÓN ON-LINE

    Directory of Open Access Journals (Sweden)

    Rubén Faúndez

    2007-11-01

    Full Text Available Las aplicaciones de simulación tienden a ser cada vez más cercanas a usuarios e industrias. Sin embargo, muchas de ellas no poseen ni la capacidad ni el conocimiento como para desarrollar internamente sus modelos de simulación. Por este motivo, y como una forma de apoyar la toma de decisiones basándose en modelos de simulación, se presenta la plataforma SOL (Simulación On Line. La metodología completa de trabajo, así como la interacción entre SOL, Empresa y Asesor, son presentadas. Su base de datos, los niveles de usuarios, sus funcionalidades, y la creación automatizada de información grafica y visual, también son explicadas. En el caso de aplicación, el uso de SOL para apoyar la toma de decisiones en una operación de movimiento de material, permite a los tomadores de decisión acceder a análisis robustos basados en información extraída de los modelos de simulación. SOL, al almacenar información, funcionar vía web, generar análisis automatizados y crear visualizaciones, permite cumplir con las expectativas de los usuarios respecto a una solución integral en simulación.

  10. Isotopic chirality

    Energy Technology Data Exchange (ETDEWEB)

    Floss, H.G. [Univ. of Washington, Seattle, WA (United States)

    1994-12-01

    This paper deals with compounds that are chiral-at least in part, due to isotope substitution-and their use in tracing the steric course of enzyme reaction in vitro and in vivo. There are other applications of isotopically chiral compounds (for example, in analyzing the steric course of nonenzymatic reactions and in probing the conformation of biomolecules) that are important but they will not be discussed in this context.

  11. Isotopic Paleoclimatology

    Science.gov (United States)

    Bowen, R.

    Paleotemperature scales were calculated by H. C. Urey and others in the 1950s to assess past temperatures, and later work using the stable isotopes of oxygen, hydrogen, and carbon employed standards such as Peedee belemnite (PDB) and Standard Mean Ocean Water (SMOW). Subsequently, subjects as diverse as ice volume and paleotemperatures, oceanic ice and sediment cores, Pleistocene/Holocene climatic changes, and isotope chronostratigraphy extending back to the Precambrian were investigated.

  12. Decay study of neutron-rich zirconium isotopes employing a Penning trap as a spectroscopy tool

    Energy Technology Data Exchange (ETDEWEB)

    Rinta-Antila, S.; Eronen, T.; Elomaa, V.V.; Hager, U.; Hakala, J.; Jokinen, A.; Karvonen, P.; Penttilae, H.; Rissanen, J.; Sonoda, T.; Saastamoinen, A.; Aeystoe, J. [University of Jyvaeskylae, Department of Physics (Finland)

    2007-01-15

    A new technique to produce isobarically pure ion beams for decay spectroscopy by using a gas-filled Penning trap was commissioned at the ion guide isotope separator on-line facility, IGISOL. {beta}-decays of neutron-rich {sup 100}Zr, {sup 102}Zr and {sup 104}Zr isotopes were studied with this technique. In addition, the Q{sub {beta}{sup -}} values of {sup 100,102,104}Zr {beta}-decays were determined from the direct mass measurements of zirconium and niobium isotopes performed with a high-precision Penning trap. The mass of {sup 104}Nb was directly measured for the first time and the obtained mass excess value for the longer-living (1{sup +}) state is -71823{+-}10 keV. For the ground states of {sup 100}Nb and {sup 102}Nb the obtained mass excess values were -79802{+-}20 keV and -76309{+-}10 keV, respectively. The observed distribution of the {beta} strength supports a prolate deformation assignment for {sup 100,102,104}Zr isotopes. (orig.)

  13. Production of radioactive isotopes from stable isotopes, for nuclear medicine; A partir d`isotopes stables, production d`isotopes radioactifs pour la medecine nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    Bourdoiseau, M. [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France). Office des Rayonnements Ionisants

    1994-12-31

    Around 15 radioactive isotopes only are used for nuclear medicine diagnosis (kinetics or preferential fixation in the body); characteristics of these {gamma} and {beta}-minus emitters are presented: period, energy, production mode (isotopic filiation, fission product separation, cyclotron, reactor); details are given on applications, production mode, properties and consumption of various isotopes: Technetium 99m, Thallium 201, Iodine 123, Indium 111, Gallium 67, Rhenium 186, Erbium 169, Yttrium 90, Iron 59, Chromium 51, Krypton 81m. 1 tab.

  14. Determination of anions with an on-line capillary electrophoresis method; Anionien on-line maeaeritys kapillaarielektroforeesilla - MPKT 10

    Energy Technology Data Exchange (ETDEWEB)

    Siren, H.; Saerme, T.; Kotiaho, T.; Hiissa, T.; Savolahti, P.; Komppa, V. [VTT Chemical Technology, Espoo (Finland)

    1998-12-31

    The aim of the study was to set-up an on-line capillary electrophoresis method for determination of anions in process waters of pulp and paper industry with exporting the results to the process control system of the mill. The quantification is important, since it will give information about the possible causes of precipitation. In recent years, the capillary electrophoresis (CE) due to its high separation efficiency has been shown as a method to take into consideration when analyzing chemical species ranging from small inorganic anions to different macromolecules. Many compounds are not easily detected in their native state, why analysis methods must be developed to improve their detection. Especially, small inorganic and organic anions which do not have chromophores are not sensitive enough for direct-UV detection. In such analyses the anions are mostly detected with indirect-UV technique. Capillary electrophoresis instruments are used to analyze samples in off-line, which seldom represent the situation in process. Therefore, on-line instrument technology with autoanalyzing settings will be needed in quality control. The development of a fully automatic capillary electrophoresis system is underway in co-operation with KCL (The Finnish Pulp and Paper Research Institute). In our research, we have first concentrated on the determination of sulphate in waters of paper industry. The method used for detection of sulphate is based on indirect-UV detection with CE, where the background electrolyte (BGE) is an absorbing mixture of secondary amines. The whole procedure for quantification of sulphate is performed within 15 minutes, after which a new sample is analyzed automatically. The only sample pretreatment is filtration, which is necessary before analysis. The concentrations of sulphate in process waters tested were between 300 and 800 ppm. Our tests show that a simultaneous determination of chloride, sulphate, nitrate, nitrite, sulphite, carbonate and oxalate is also

  15. Stable isotope utilization methodology; Methodologie de l`emploi des isotopes stables

    Energy Technology Data Exchange (ETDEWEB)

    Roth, E. [Conservatoire National des Arts et Metiers (CNAM), 75 - Paris (France)

    1994-12-31

    The various applications of stable isotope utilization are reviewed, as a function of their specific properties: poly-isotopic abundance modification is used for tracer applications; the accurate measurement of the stable isotope abundance may be applied to isotopic dilution for ultra-trace measurement, physical constant determination, fluid volume and concentration measurement; isotopic effects, such as reaction equilibrium differences are used for separation and identification of molecule active centers (pharmacology, paleoclimatology, hydrogeological studies) while reaction rate differences (competitive and non competitive methods) are used for the study of reaction mechanisms, such as enzymatic reactions. Analysis techniques (mass spectrometry, nuclear magnetic resonance, optical methods) are reviewed. 2 figs., 18 refs.

  16. Isotopic Changes During Digestion: Protein

    Science.gov (United States)

    Tuross, N.

    2013-12-01

    Nutrient and hydrological inputs traverse a complicated route of pH, enzymatic and cellular processes in digestion in higher animals. The end products of digestion are the starting products for biosynthesis that are often used to interpret past life-ways. Using an artificial gut system, the isotopic changes (dD, d18O, d13C and d15N) of protein are documented. Three separate protein sources are subjected to the conditions, chemical and enzymatic, found in the stomach and upper small intestine with only a small shift in the oxygen isotopic composition of the proteins observed. Middle to lower small intestine parameters produced both greater isotopic effects and significantly lower molecular weight products. The role of the gastric enterocyte and the likely involvement of the internal milieu of this cell in the isotopic composition of amino acids that are transported to the liver are reported.

  17. Robust on-line monitoring of biogas processes; Robusta maettekniker on-line foer optimerad biogasproduktion

    Energy Technology Data Exchange (ETDEWEB)

    Nordberg, Aake; Hansson, Mikael; Kanerot, Mija; Krozer, Anatol; Loefving, Bjoern; Sahlin, Eskil

    2010-03-15

    Although demand for biomethane in Sweden is higher than ever, many Swedish codigestion plants are presently operated below their designed capacity. Efforts must be taken to increase the loading rate and guarantee stable operation and high availability of the plants. There are currently no commercial systems for on-line monitoring, and due to the characteristics of the material, including corrosion and tearing, robust applications have to be developed. The objective of this project was to identify and study different monitoring technologies with potential for on-line monitoring of both substrate mixtures and anaerobic digester content. Based on the prerequisites and demands at Boraas Energi och Miljoe AB's (BEMAB, the municipal energy and waste utility in the city of Boraas, Sweden) biogas plant, the extent of the problems, measurement variables and possible ways of managing these issues have been identified and prioritized. The substrate mixtures in question have a high viscosity and are inhomogeneous with variation in composition, which calls for further homogenization, dilution and filtration to achieve high precision in the necessary analyses. Studies of using different mixers and mills showed that the particle size (800 mum) needed for on-line COD measurement could not be achieved. The problem of homogenization can be avoided if indirect measurement methods are used. Laboratory tests with NIR (near-infra red spectroscopy) showed that VS can be predicted (R2=0,78) in the interval of 2-9% VS. Furthermore, impedance can give a measurement of soluble components. However, impedance is not sensitive enough to give a good measurement of total TS. Microwave technology was installed at the production plant and showed a faster response to changes in TS than the existing TS-sensor. However, due to technical problems, the evaluation only could be done during a limited period of ten days. BEMAB will continue the measurements and evaluation of the instrument. The

  18. Laser Isotope Enrichment for Medical and Industrial Applications

    Energy Technology Data Exchange (ETDEWEB)

    Leonard Bond

    2006-07-01

    Laser Isotope Enrichment for Medical and Industrial Applications by Jeff Eerkens (University of Missouri), Jay Kunze (Idaho State University), and Leonard Bond (Idaho National Laboratory) The principal isotope enrichment business in the world is the enrichment of uranium for commercial power reactor fuels. However, there are a number of other needs for separated isotopes. Some examples are: 1) Pure isotopic targets for irradiation to produce medical radioisotopes. 2) Pure isotopes for semiconductors. 3) Low neutron capture isotopes for various uses in nuclear reactors. 4) Isotopes for industrial tracer/identification applications. Examples of interest to medicine are targets to produce radio-isotopes such as S-33, Mo-98, Mo-100, W-186, Sn-112; while for MRI diagnostics, the non-radioactive Xe-129 isotope is wanted. For super-semiconductor applications some desired industrial isotopes are Si-28, Ga-69, Ge-74, Se-80, Te-128, etc. An example of a low cross section isotope for use in reactors is Zn-68 as a corrosion inhibitor material in nuclear reactor primary systems. Neutron activation of Ar isotopes is of interest in industrial tracer and diagnostic applications (e.g. oil-logging). . In the past few years there has been a sufficient supply of isotopes in common demand, because of huge Russian stockpiles produced with old electromagnetic and centrifuge separators previously used for uranium enrichment. Production of specialized isotopes in the USA has been largely accomplished using old ”calutrons” (electromagnetic separators) at Oak Ridge National Laboratory. These methods of separating isotopes are rather energy inefficient. Use of lasers for isotope separation has been considered for many decades. None of the proposed methods have attained sufficient proof of principal status to be economically attractive to pursue commercially. Some of the authors have succeeded in separating sulfur isotopes using a rather new and different method, known as condensation

  19. DOE-EPRI On-Line Monitoring Implementation Guidelines

    Energy Technology Data Exchange (ETDEWEB)

    E. Davis, R. Bickford

    2003-01-02

    Industry and EPRI experience at several plants has shown on-line monitoring to be very effective in identifying out-of-calibration instrument channels or indications of equipment-degradation problems. The EPRI implementation project for on-line monitoring has demonstrated the feasability of on-line monitoring at several participating nuclear plants. The results have been very enouraging, and substantial progress is anticipated in the coming years.

  20. Poss On-line (Personalisation of Self-Service Solutions across On-line platforms)

    DEFF Research Database (Denmark)

    Nielsen, Janni; Nielsen, Lene; Jespersen, Mikkel

    2005-01-01

    The project on Personalisation of Self-service Solutions across On-line Platforms (POSS ON-LINE) focuses on users, clients, and self-service solutions. It is based on the understanding that clients and users are different and have different goals, and that self-service takes place in different co...... at the process of development. However, we lack methods to predict user behaviour without having to deal with huge amounts of data and data from both quantitative data as well as life world observations are required....... the client and the user. The system gathers data about the user, which enables the client to push information to the user. Personalisation enables graphic user interface design that is personalised and relevant to the individual user and invites the user to get access to information with less strain....... Personalisation of self-service solutions is promising and IT companies are experiencing an increase in the clients' demands. At the same time the development of solutions moves within a shorter and shorter time span. Hence the process of innovations is paced and there is an increasing need of new ways of looking...

  1. Applications of on-line weak affinity interactions in free solution capillary electrophoresis

    DEFF Research Database (Denmark)

    Heegaard, Niels H H; Nissen, Mogens H; Chen, David D Y

    2002-01-01

    The impressive selectivity offered by capillary electrophoresis can in some cases be further increased when ligands or additives that engage in weak affinity interactions with one or more of the separated analytes are added to the electrophoresis buffer. This on-line affinity capillary...... enantiomers and on using capillary electrophoresis to characterize such interactions quantitatively. We describe the equations for binding isotherms, illustrate how selectivity can be manipulated by varying the additive concentrations, and show how the methods may be used to estimate binding constants. On......-line affinity capillary electrophoresis methods are especially valuable for enantiomeric separations and for functional characterization of the contents of biological samples that are only available in minute quantities....

  2. Developments towards in-gas-jet laser spectroscopy studies of actinium isotopes at LISOL

    Energy Technology Data Exchange (ETDEWEB)

    Raeder, S., E-mail: s.raeder@gsi.de [KU Leuven, Instituut voor Kern- en Stralingsfysica, Celestijnenlaan 200D, B-3001 Leuven (Belgium); Helmholtz-Institut Mainz, 55128 Mainz (Germany); GSI Helmholtzzentrum für Schwerionenforschung GmbH, Planckstraße 1, 64291 Darmstadt (Germany); Bastin, B. [GANIL, CEA/DSM-CNRS/IN2P3, B.P. 55027, 14076 Caen (France); Block, M. [Helmholtz-Institut Mainz, 55128 Mainz (Germany); GSI Helmholtzzentrum für Schwerionenforschung GmbH, Planckstraße 1, 64291 Darmstadt (Germany); Institut für Kernchemie, Johannes Gutenberg Universität, 55128 Mainz (Germany); Creemers, P. [KU Leuven, Instituut voor Kern- en Stralingsfysica, Celestijnenlaan 200D, B-3001 Leuven (Belgium); Delahaye, P. [GANIL, CEA/DSM-CNRS/IN2P3, B.P. 55027, 14076 Caen (France); Ferrer, R. [KU Leuven, Instituut voor Kern- en Stralingsfysica, Celestijnenlaan 200D, B-3001 Leuven (Belgium); Fléchard, X. [LPC Caen, ENSICAEN, Université de Caen, CNRS/IN2P3, Caen (France); Franchoo, S. [Institute de Physique Nucléaire (IPN) d’Orsay, 91406 Orsay, Cedex (France); Ghys, L. [KU Leuven, Instituut voor Kern- en Stralingsfysica, Celestijnenlaan 200D, B-3001 Leuven (Belgium); SCK-CEN, Belgian Nuclear Research Center, Boeretang 200, 2400 Mol (Belgium); Gaffney, L.P.; Granados, C. [KU Leuven, Instituut voor Kern- en Stralingsfysica, Celestijnenlaan 200D, B-3001 Leuven (Belgium); Heinke, R. [Institut für Physik, Johannes Gutenberg Universität, 55128 Mainz (Germany); Hijazi, L. [GANIL, CEA/DSM-CNRS/IN2P3, B.P. 55027, 14076 Caen (France); and others

    2016-06-01

    To study exotic nuclides at the borders of stability with laser ionization and spectroscopy techniques, highest efficiencies in combination with a high spectral resolution are required. These usually opposing requirements are reconciled by applying the in-gas-laser ionization and spectroscopy (IGLIS) technique in the supersonic gas jet produced by a de Laval nozzle installed at the exit of the stopping gas cell. Carrying out laser ionization in the low-temperature and low density supersonic gas jet eliminates pressure broadening, which will significantly improve the spectral resolution. This article presents the required modifications at the Leuven Isotope Separator On-Line (LISOL) facility that are needed for the first on-line studies of in-gas-jet laser spectroscopy. Different geometries for the gas outlet and extraction ion guides have been tested for their performance regarding the acceptance of laser ionized species as well as for their differential pumping capacities. The specifications and performance of the temporarily installed high repetition rate laser system, including a narrow bandwidth injection-locked Ti:sapphire laser, are discussed and first preliminary results on neutron-deficient actinium isotopes are presented indicating the high capability of this novel technique.

  3. Isotopic effects on the phonon modes in boron carbide.

    Science.gov (United States)

    Werheit, H; Kuhlmann, U; Rotter, H W; Shalamberidze, S O

    2010-10-01

    The effect of isotopes ((10)B-(11)B; (12)C-(13)C) on the infrared- and Raman-active phonons of boron carbide has been investigated. For B isotopes, the contributions of the virtual crystal approximation, polarization vector and isotopical disorder are separated. Boron and carbon isotope effects are largely opposite to one another and indicate the share of the particular atoms in the atomic assemblies vibrating in specific phonon modes. Some infrared-active phonons behave as expected for monatomic boron crystals.

  4. 稳定同位素13C分离级联装置的模拟优化研究%Simulation and Optimization Research of Stable Isotope 13C Separation Cascade Equipment

    Institute of Scientific and Technical Information of China (English)

    田叶盛; 李虎林; 许保云; 李良君

    2012-01-01

    A stable isotope 13C separation three-stage cascade equipment using carbon monoxide (CO) cryogenic rectification was designed. The distillation columns were packed with self-developed high efficiency structure packing PACK-13C of 38 m height. The columns diameters are 0. 15 m, 0.08 m and 0.05 m respectively. The uniform design method was taken to optimize the cascades equipment. The effects of the reflux ratio, feed amount, inter-columns material flow on the 13C product purity and the energy consumption were analyzed synthetically. The mathematical model of the product purity relative to the reflux rati-o, feed amount, and inter-columns material flow and the mathematical model of the energy consumption relative to above decision variables were obtained by quadratic polynomial step-wise regression analysis of the experimental data. Then, the optimal operation conditions at the lowest energy consumptibn were achieved by the method of genetic algorithm. If the 13C product purity is more than 93%, the optimal inter-columns material flows are 18. 056 mol/ h, 236. 50 mol/h, 32. 400 mol/h and the reflux ratio is 74. 824. Compared with the initial designed conditions, the optimal operation conditions can reduce the energy consumption. The method of simulation and optimization could be applied to design 13C industrial and realize optimization design in traditional distillation process.%本工作设计了一套利用CO低温精馏分离稳定同位素13C的三级联装置,其填料层高度为38 m,塔径分别为0.15、0.08和0.05 m,塔内装填自主研发的高比表面PACK-13C专用填料.采用均匀设计方法进行级联装置的优化设计,综合分析了不同的回流比、原料量和级间进料量对同位素13C产品丰度和生产能耗的影响.对实验数据进行二次多项式逐步回归分析,获得了产品丰度与塔顶回流比、原料量及级间流量和能耗费用与回流比、原料量及级间流量的模型方程,并利用遗传算法对

  5. Increasing of MERARG experimental performances: on-line fission gas release measurement by mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Pontillon, Y.; Capdevila, H.; Clement, S. [CEA, DEN, DEC, SA3C, LAMIR, F-13108 Saint Paul lez Durance, (France); Guigues, E.; Janulyte, A.; Zerega, Y.; Andre, J. [Aix-Marseille Universite, LISA EA 4672, 13397 MARSEILLE cedex 20, (France)

    2015-07-01

    The MERARG device - implemented at the LECASTAR Hot Laboratory, at the CEA Cadarache - allows characterizing nuclear fuels with respect to the behaviour of fission gases during thermal transients representative of normal or off normal operating nuclear power plant conditions. The fuel is heated in order to extract a part or the total gas inventory it contains. Fission Gas Release (FGR) is actually recorded by mean of both on-line gamma spectrometry station and micro gas chromatography. These two devices monitor the quantity and kinetics of fission gas release rate. They only address {sup 85}Kr radioactive isotope and the elemental quantification of Kr, Xe and He (with a relatively low detection limit in the latter case, typically 5-10 ppm). In order to better estimate the basic mechanisms that promote fission gas release from irradiated nuclear fuels, the CEA fuel study department decided to improve its experimental facility by modifying MERARG to extend the studies of gamma emitter fission gases to all gases (including Helium) with a complete isotopic distribution capability. To match these specifications, a Residual Gas Analyser (RGA) has been chosen as mass spectrometer. This paper presents a review of the main aspects of the qualification/calibration phase of the RGA type analyser. In particular, results recorded over three mass ranges 1-10 u, 80-90 u and 120-140 u in the two classical modes of MERARG, i.e. on-line and off-line measurements are discussed. Results obtained from a standard gas bottle show that the quantitative analysis at a few ppm levels can be achieved for all isotopes of Kr and Xe, as well as masses 2 and 4 u. (authors)

  6. Isotope Harvesting Opportunities at FRIB

    Science.gov (United States)

    Morrissey, David

    2017-01-01

    The fragmentation of fast heavy ion beams now at the National Superconducting Cyclotron Laboratory (NSCL) and in the future at the Facility for Rare Isotope Beams (FRIB) under construction produce an unprecedentedly broad spectrum of radionuclides but only a small fraction are used in the on-line rare-isotope program. Projectile fragmentation facilities provide an electromagnetically purified beam of a single projectile fragment for nuclear physics experiments ranging from low energy astrophysics, through nuclear structure studies, to probing fundamental symmetries. By augmenting the NSCL and FRIB production facilities with complimentary collection and purification of discarded ions, called isotope harvesting with chemical purification, many other nuclides will become available for off-line experiments in parallel with the primary experiment. A growing user community has established a list of key target isotopes and is working with the FRIB design team to allow inclusion of necessary equipment in the future. An overview of the possibilities and the techniques will be presented in this talk. Supported by Office of Science, US DOE and Michigan State University.

  7. On-line radiochemical assay for monoamine oxidase utilizing high-performance liquid chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Nissinen, E.; Linko-Loeppoenen SMae; Maennistoe P4

    1984-12-01

    A fast and sensitive assay for the determination of monoamine oxidase activity was developed. The method is based on the separation and quantitation of /sup 14/C-labeled assay products by high-performance liquid chromatography, which is interfaced directly into a flow-through radioactivity detector. This allows on-line quantitation of the radioactive compounds with picomole sensitivity. The method makes possible the complete separation and detection of the deaminated products of monoamine oxidase A and B substrates benzylamine and 5-hydroxytryptamine, respectively. This assay has been applied to the measurement of monoamine oxidase A and B activities in rat brain.

  8. On-line method of determining utilization factor in Hg-196 photochemical separation process

    Science.gov (United States)

    Grossman, Mark W.; Moskowitz, Philip E.

    1992-01-01

    The present invention is directed to a method for determining the utilization factor [U] in a photochemical mercury enrichment process (.sup.196 Hg) by measuring relative .sup.196 Hg densities using absorption spectroscopy.

  9. Capillary Separation: Micellar Electrokinetic Chromatography

    Science.gov (United States)

    Terabe, Shigeru

    2009-07-01

    Micellar electrokinetic chromatography (MEKC), a separation mode of capillary electrophoresis (CE), has enabled the separation of electrically neutral analytes. MEKC can be performed by adding an ionic micelle to the running solution of CE without modifying the instrument. Its separation principle is based on the differential migration of the ionic micelles and the bulk running buffer under electrophoresis conditions and on the interaction between the analyte and the micelle. Hence, MEKC's separation principle is similar to that of chromatography. MEKC is a useful technique particularly for the separation of small molecules, both neutral and charged, and yields high-efficiency separation in a short time with minimum amounts of sample and reagents. To improve the concentration sensitivity of detection, several on-line sample preconcentration techniques such as sweeping have been developed.

  10. ON-LINE PREEMPTIVE SCHEDULING ON UNIFORM MACHINES

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yuzhong; WANG Shouyang; Bo Chen; ZHANG Shuxia

    2001-01-01

    We address the problem of preemptively schedule on-line jobs on arbitrary muniformly related machines with the objective of minimizing the schedule length. We provide the first on-line algorithm for this general problem, and show that the algorithm being the speeds of the m machines.

  11. From Off-line to On-line Handwriting Recognition

    NARCIS (Netherlands)

    Lallican, P.; Viard-Gaudin, C.; Knerr, S.

    2004-01-01

    On-line handwriting includes more information on time order of the writing signal and on the dynamics of the writing process than off-line handwriting. Therefore, on-line recognition systems achieve higher recognition rates. This can be concluded from results reported in the literature, and has been

  12. On-Line and Off-Line Assessment of Metacognition

    Science.gov (United States)

    Saraç, Seda; Karakelle, Sema

    2012-01-01

    The study investigates the interrelationships between different on-line and off-line measures for assessing metacognition. The participants were 47 fifth grade elementary students. Metacognition was assessed through two off-line and two on-line measures. The off-line measures consisted of a teacher rating scale and a self-report questionnaire. The…

  13. On-line characterization of a hybridoma cell culture process.

    Science.gov (United States)

    Zhou, W; Hu, W S

    1994-06-20

    The on-line determination of the physiological state of a cell culture process requires reliable on-line measurements of various parameters and calculations of specific rates from these measurements. The cell concentration of a hybridoma culture was estimated on-line by measuring optical density (OD) with a laser turbidity probe. The oxygen uptake rate (OUR) was determined by monitoring dynamically dissolved oxygen concentration profiles and closing oxygen balances in the culture. The base addition for neutralizing lactate produced by cells was also monitored on-line via a balance. Using OD and OUR measurements, the specific growth and specific oxygen consumption rates were determined on-line. By combining predetermined stoichiometric relationships among oxygen and glucose consumption and lactate production, the specific glucose consumption and lactate production rates were also calculated on-line. Using these on-line measurements and calculations, the hybridoma culture process was characterized on-line by identifying the physiological states. They will also facilitate the implementation of nutrient feeding strategies for fed-batch and perfusion cultures. (c) 1994 John Wiley & Sons, Inc.

  14. On-line optimal control of greenhouse crop cultivation.

    NARCIS (Netherlands)

    Straten, van G.

    1996-01-01

    Thus far, optimal control has primarily been investigated for seasonal crop growth optimization. On-line aspects have received much less attention. The decomposition between long term strategies and on-line control, however, is not trivial. Appreciable losses occur when set-points generated by seaso

  15. On-line optimal control of greenhouse crop cultivation.

    NARCIS (Netherlands)

    Straten, van G.

    1996-01-01

    Thus far, optimal control has primarily been investigated for seasonal crop growth optimization. On-line aspects have received much less attention. The decomposition between long term strategies and on-line control, however, is not trivial. Appreciable losses occur when set-points generated by seaso

  16. Algorithms for semi on-line multiprocessor scheduling problems

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In the classical multiprocessor scheduling problems, it is assumed that the problems are considered in off-line or on-line environment. But in practice, problems are often not really off-line or on-line but somehow in between. This means that, with respect to the on-line problem, some further information about the tasks is available, which allows the improvement of the performance of the best possible algorithms. Problems of this class are called semi on-line ones. The authors studied two semi on-line multiprocessor scheduling problems, in which, the total processing time of all tasks is known in advance, or all processing times lie in a given interval. They proposed approximation algorithms for minimizing the makespan and analyzed their performance guarantee. The algorithms improve the known results for 3 or more processor cases in the literature.

  17. Cryogenic separation of hydrogen isotopes in single-walled carbon and boron-nitride nanotubes: insight into the mechanism of equilibrium quantum sieving in quasi-one-dimensional pores.

    Science.gov (United States)

    Kowalczyk, Piotr; Gauden, Piotr A; Terzyk, Artur P

    2008-07-17

    Quasi-one-dimensional cylindrical pores of single-walled boron nitride and carbon nanotubes efficiently differentiate adsorbed hydrogen isotopes at 33 K. Extensive path integral Monte Carlo simulations revealed that the mechanisms of quantum sieving for both types of nanotubes are quantitatively similar; however, the stronger and heterogeneous external solid-fluid potential generated from single-walled boron nitride nanotubes enhanced the selectivity of deuterium over hydrogen both at zero coverage and at finite pressures. We showed that this enhancement of the D(2)/H(2) equilibrium selectivity results from larger localization of hydrogen isotopes in the interior space of single-walled boron nitride nanotubes in comparison to that of equivalent single-walled carbon nanotubes. The operating pressures for efficient quantum sieving of hydrogen isotopes are strongly depending on both the type as well as the size of the nanotube. For all investigated nanotubes, we predicted the occurrence of the minima of the D(2)/H(2) equilibrium selectivity at finite pressure. Moreover, we showed that those well-defined minima are gradually shifted upon increasing of the nanotube pore diameter. We related the nonmonotonic shape of the D(2)/H(2) equilibrium selectivity at finite pressures to the variation of the difference between the average kinetic energy computed from single-component adsorption isotherms of H(2) and D(2). In the interior space of both kinds of nanotubes hydrogen isotopes formed solid-like structures (plastic crystals) at 33 K and 10 Pa with densities above the compressed bulk para-hydrogen at 30 K and 30 MPa.

  18. Conformational effect of dicyclo-hexano-18-crown-6 on isotopic fractionation of zinc: DFT approach

    Energy Technology Data Exchange (ETDEWEB)

    Boda, A.; Singha Deb, A. K.; Ali, Sk. M.; Shenoy, K. T.; Ghosh, S. K. [Chemical Engineering Division, Chemical Engineering Group, Bhabha Atomic Research Centre, Mumbai-400085 (India)

    2014-04-24

    Generalized gradient approximated BP86 density functional employing triple zeta valence plus polarization (TZVP) basis set has been used to compute the reduced partition function ratio and isotopic separation factor for zinc isotopes. The isotopic separation factor was found to be in good agreement with the experimental results. The isotopic separation factor was found to depend on the conformation of the crown ether ligand. The trans-trans conformation shows the highest fractionation compared to cis-cis conformer. The present theoretical results can thus be used to plan the isotope separation experiments.

  19. Decay of the neutron-rich isotope {sup 113}Ru to {sup 113}Rh

    Energy Technology Data Exchange (ETDEWEB)

    Kurpeta, J.; Plochocki, A. [Institute of Experimental Physics, Warsaw University (Poland); Lhersonneau, G.; Wang, J.C.; Dendooven, P.; Honkanen, A.; Huhta, M.; Oinonen, M.; Penttilae, H.; Peraejaervi, K.; Persson, J.R. [Department of Physics, University of Jyvaeskylae (Finland); Aeystoe, J. [Department of Physics, University of Jyvaeskylae (Finland); EP-ISOLDE, CERN, Geneva (Switzerland)

    2002-04-01

    The decay of neutron-rich isotope {sup 113}Ru obtained as on-line mass separated product of proton-induced fission has been investigated by {gamma}{gamma} coincidence and spectrum multiscaling measurements. Decay schemes for both low- and high-spin isomers of {sup 113}Ru have been constructed. The level scheme of {sup 113}Rh is considerably extended. Systematics of the lowest-lying rhodium levels is smooth. The picture of shape coexistence established for neutron-rich Rh isotopes near-neutron midshell is confirmed with the observation of a K=1/2 deformed band, with its 3/2{sup +} state at 600 keV being the lowest-lying level and of probable 7/2{sup +} and 5/2{sup +} band members. A large fraction of {beta} feeding is found to populate high-lying levels in {sup 113}Rh. The GT strength in {sup 113}Ru{sup m} decay is significantly larger than for the decay of {sup 113}Ru{sub g} and of lighter rhodium isotopes. (orig.)

  20. Nuclear Physics Programs for the Future Rare Isotope Beams Accelerator Facility in Korea

    CERN Document Server

    Moon, Chang-Bum

    2016-01-01

    We present nuclear physics programs based on the planned experiments using rare isotope beams (RIBs) for the future Korean Rare Isotope Beams Accelerator facility; RAON. This ambitious facility has both an Isotope Separation On Line (ISOL) and fragmentation capability for producing RIBs and accelerating beams of wide range mass of nuclides with energies of a few to hundreds MeV per nucleon. Low energy RIBs at Elab = 5 to 20 MeV per nucleon are for the study of nuclear structure and nuclear astrophysics toward and beyond the drip lines while higher energy RIBs produced by in-flight fragmentation with the re-accelerated ions from the ISOL enable to explore the neutron drip lines in intermediate mass regions. The planned programs have goals for investigating nuclear structures of the exotic nuclei toward and beyond the nucleon drip lines by addressing the following issues: how the shell structure evolves in areas of extreme proton to neutron imbalance; whether the isospin symmetry maintains in isobaric mirror nu...

  1. Identification of neutron-rich new isotopes and their half-lives

    Energy Technology Data Exchange (ETDEWEB)

    Okano, Kotoyuki; Taniguchi, Akihiro [Kyoto Univ., Kumatori, Osaka (Japan). Research Reactor Inst.

    1996-03-01

    Recently, some new isotopes such as {sup 156}Pm, {sup 155}Nd, {sup 154}Pr, {sup 152}Ce were identified using on-line isotope separation apparatus (KUR-ISOL). The half-lives of these isotopes were several seconds and those of other unknown nuclides are assumed to be around one second or extremely shorter. Detections of {sup 150}La, {sup 153}Ce, {sup 157}Nd etc. have not been succeeded by previous studies. In order to raise the efficiency for identification of short-lived nuclides, it seems essential to remarkably increase the beam strength of KUR-ISOL and to secure its safety operating. A mixed-gas jet method has been developed using a mixed gas of N{sub 2} and He and the beam strength increased by more than one digit. In addition, the exchange over time for gas was shortened by increasing the gas flow volume. Next, various aerosols were tested to select a stable and high efficient ion source and PbI{sub 2} aerosol was chosen as the most suitable one. A 4{pi}{beta}-{gamma}-coinsidence spectrometer with plastic scintillator of 1 mm in depth was constructed and simultaneous measurement for {beta}-ray and {gamma}-ray as well as measurement for a single spectre became possible. Thus identification of {sup 150}La was succeeded by those improvements of KUR-ISOL and the use of 4{pi}{beta}-{gamma}-coinsidence spectrometer. (M.N.)

  2. On-line sample-pre-treatment schemes for trace-level determinations of metals by coupling flow injection or sequential injection with ICP-MS

    DEFF Research Database (Denmark)

    Wang, Jianhua; Hansen, Elo Harald

    2003-01-01

    for on-line matrix separation and pre-concentration of trace levels of metals with detection by ICP-MS. It highlights some of the frequently applied on-line, sample-pre-treatment schemes, including solid phase extraction (SPE), on-wall molecular sorption and precipitate/(co)-precipitate retention using...... a polytetrafluoroethylene (PTFE) knotted reactor (KR), solvent extraction-back extraction and hydride/vapor generation. It also addresses a novel, robust approach, whereby the protocol of SI-LOV-bead injection (BI) on-line separation and pre-concentration of ultra-trace levels of metals by a renewable microcolumn...

  3. On-line Autonomous Learning Based on Leamerg Expectation

    Institute of Scientific and Technical Information of China (English)

    李利娜

    2008-01-01

    On-line autonomous learning of College English is one of the important reforms in colleges recently.This paper aims to explore the changes of teachers'role in the new on-line setting.The article first reviews the theoretical study of learner autonomy,then makes a practical investigation into the attitude and expectation learners have on teachers through a self-designed questionnaire,and explores that teachers should make an adjustment to their role orientation and changes their roles into motivators,evaluators and resources supphers in the new on-line setting.

  4. On-line Classical Guitar Course: Blogs for Music Education

    OpenAIRE

    José Luis Navarro; Gilles Lavigne; G. Guadalupe Martínez Salgado

    2009-01-01

    This article introduces an on-line course constructed by means of a blog. The tool was the main goal of a research project titled “Develop, Implementation and evaluation of a Hybrid Course Face to face-On Line for Teaching the Beginning to Play the Classical Guitar”. This work was a three steep project in which it was implemented, applied and evaluated. The on-line course was intended to prepare the students to learn the basic principles to start in classical music with the guitar. The result...

  5. Understanding on-line community: the affordances of virtual space

    Directory of Open Access Journals (Sweden)

    Karen Ruhleder

    2002-01-01

    Full Text Available Increasing numbers of on-line venues for learning are emerging as virtual communities become more accessible and commonplace. This paper looks at one particular virtual community, an on-line degree programme at the University of Illinois, Urbana-Champaign, which offers an M.S. in Library and Information Science (called LEEP. It draws on a framework presented by Mynatt, et al. (1998, which provides a lens for talking about on-line community as a set of affordances. This framework is applied to illustrate the interactions, artefacts, and expectations that shape this community.

  6. Sampling and sample preparation development for analytical and on-line measurement techniques of process liquids; Naeytteenoton ja kaesittelyn kehittaeminen prosessinesteiden analytiikan ja on-line mittaustekniikan tarpeisiin - MPKT 11

    Energy Technology Data Exchange (ETDEWEB)

    Karttunen, K. [Oulu Univ. (Finland)

    1998-12-31

    Main goal of the research project is to develop sampling and sample handling methods and techniques for pulp and paper industry to be used for analysis and on-line purposes. The research focus specially on the research and development of the classification and separation methods and techniques needed for liquid and colloidal substances as well as in ion analysis. (orig.)

  7. A new digestion and chemical separation technique for rapid and highly reproducible determination of Lu/Hf and Hf isotope ratios in geological materials by mc-ICP-MS

    DEFF Research Database (Denmark)

    Bizzarro, Martin; Baker, J.A.; Ulfbeck, D.

    2003-01-01

    metaborate. High field strength elements (HFSE) and rare earth elements (REE) are separated from this solution by co-precipitation with iron hydroxide. The dissolved precipitate (in 2 mol l HCl) is loaded directly onto a standard cation exchange column which separates remaining sample matrix from the heavy...

  8. A new method for immunoassays using field-flow fractionation with on-line, continuous chemiluminescence detection.

    Science.gov (United States)

    Melucci, D; Guardigli, M; Roda, B; Zattoni, A; Reschiglian, P; Roda, A

    2003-06-13

    Chemiluminescence detection has already been combined with different separation techniques such as HPLC and capillary electrophoresis. In this work, it was applied to gravitational field-flow fractionation, a low-cost, flow-assisted separation technique for micronsized particles suited to further on-line detection of the separated analytes. Horseradish peroxidase was used as model sample, either free in solution or immobilized onto micronsized, polystyrene beads. The chemiluminescent substrates were added directly into the mobile phase, and the continuous, steady-state chemiluminescence generated during elution was detected on-line by either a flow-through luminometer or a CCD camera. Ultra-low detection limits, two orders of magnitude lower than those achievable with spectrophotometric detection, were found. The possibility to fully separate and quantitate free and bead-immobilized enzymes is reported, as a step towards the development of multianalyte, ultra-sensitive, micronsized beads-based flow-assisted immunoassays.

  9. Yields and spectroscopy of radioactive isotopes at LOHENGRIN and ISOLDE

    CERN Document Server

    Köster, U

    1999-01-01

    Yields of radioactive nuclei were measured at two facilities: the recoil separator LOHENGRIN at the Institut Laue Langevin in Grenoble and the on-line isotope separator ISOLDE at CERN in Geneva. At LOHENGRIN the yields of light charged particles were measured from thermal neutron induced ternary fission of several actinide targets: 233U, 235U, 239Pu, 241Pu and 245Cm. Thin targets are brought into a high neutron flux. The produced nuclei leave these with the recoil obtained in the fission reaction. They are measured at different energies and ionic charge states. After corrections for the experimental acceptance, the time behaviour of the fission rate and the ionic charge fraction, the yields are integrated over the kinetic energy distribution. Comparing these yields with the predictions of various ternary fission models shows that the most abundant nuclides are well reproduced. On the other hand the models overestimate significantly the production of more "exotic" nuclides with an extreme N/Z ratio. Therefore ...

  10. Applications of on-line multidimensional chromatography to solvent refined coal

    Energy Technology Data Exchange (ETDEWEB)

    Chen, T.M.; Apffel, J.A.; McNair, H.M.

    1981-03-29

    Solvent refined coal (SRC) is a complex mixture predominantly aromatic in nuture, and attempts to elucidate structure or compositional details by a single analytical technique have had limited success. Several on-line multidimensional chromatographic techniques were chosen to examine the hexane soluble fraction of SRC. These techniques include LC (silica gel)/LC (reverse phase); LC/GC; and LC/LC/Fluorescence. The latter technique proved to be the most useful and are discussed in detail in this paper. The conclusions of this study are: on-line coupled chromatographic techniques allow separations not easily done off-line. The on-line techniques are easily automated (increasing reproducibility) and allow small transfer volumes between systems. The main limitation with LC/LC is the incompatibility of mobile phases when the columns are normal phase and reverse phase. With LC/GC the main problem is quantitation (since only a portion of the peak is injected) and degradation of GC columns with some LC mobile phases. The use of selective detectors in series is a good technique to examine complex fractions like SRC and enhances the separating power.

  11. On-line cation-exchange preconcentration and capillary electrophoresis coupled by tee joint interface.

    Science.gov (United States)

    Zhang, Zhao-Xiang; He, You-Zhao

    2005-02-25

    An on-line preconcentration method based on ion exchange solid phase extraction was developed for the determination of cationic analytes in capillary electrophoresis (CE). The preconcentration-separation system consisted of a preconcentration capillary bonded with carboxyl cation-exchange stationary phase, a separation capillary for zone electrophoresis and a tee joint interface of the capillaries. Two capillaries were connected closely inside a 0.3 mm i.d. polytetrafluoroethylene tube with a side opening and fixed together by the interface. The preparations of the preconcentration capillaries and interface were described in detail in this paper. The on-line preconcentration and separation procedure of the analysis system included washing and conditioning the capillaries, loading analytes, filling with buffer solution, eluting analytes and separating by capillary zone electrophoresis (CZE). Several analysis parameters, including sample loading flow rate and time, eluting solution and volume, inner diameter and length of preconcentration capillary etc., were investigated. The proposed method enhanced the detection sensitivity of CE-UV about 5000 times for propranolol and metoprolol compared with normally electrokinetic injection. The detection limits of propranolol and metoprolol were 0.02 and 0.1 microg/L with the proposed method respectively, whereas those were 0.1 and 0.5 mg/L with conventional electrokinetic injection. The experiment results demonstrate that the proposed technique can increase the preconcentration factor evidently.

  12. Separation Logic

    DEFF Research Database (Denmark)

    Reynolds, John C.

    2002-01-01

    expressions) for accessing and modifying shared structures, and for explicit allocation and deallocation of storage. Assertions are extended by introducing a "separating conjunction" that asserts that its sub-formulas hold for disjoint parts of the heap, and a closely related "separating implication". Coupled......, dynamically allocated arrays, and recursive procedures. We will also discuss promising future directions....

  13. DESIR high resolution separator at GANIL, France

    Directory of Open Access Journals (Sweden)

    Toprek Dragan

    2012-01-01

    Full Text Available A high-resolution separator for the SPIRAL2/DESIR project at GANIL has been designed. The extracted isotopes from SPIRAL2 will be transported to and cooled in a RFQ cooler yielding beams with very low transverse emittance and energy spread. These beams will then be accelerated to 60 keV and sent to a high-resolution mass separator where a specific isotope will be selected. The good beam properties extracted from the RFQ cooler will allow one to obtain a mass resolution of č26000 with the high-resolution mass separator.

  14. On-Line Trajectory Retargeting for Alternate Landing Sites Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Barron Associates, Inc. proposes to develop a novel on-line trajectory optimization approach for Reusable Launch Vehicles (RLVs) under failure scenarios, targeting...

  15. An automated on-line multidimensional HPLC system for protein and peptide mapping with integrated sample preparation

    NARCIS (Netherlands)

    Wagner, K.; Miliotis, T.; Marko-Varga, G; Bischoff, Rainer; Unger, K.K.

    2002-01-01

    A comprehensive on-line two-dimensional 2D-HPLC system with integrated sample preparation was developed for the analysis of proteins and peptides with a molecular weight below 20 kDa. The system setup provided fast separations and high resolving power and is considered to be a complementary techniqu

  16. ON-LINE SCHEDULING WITH REJECTION ON IDENTICAL PARALLEL MACHINES

    Institute of Scientific and Technical Information of China (English)

    Cuixia MIAO; Yuzhong ZHANG

    2006-01-01

    In this paper, we consider the on-line scheduling of unit time jobs with rejection on m identical parallel machines. The objective is to minimize the total completion time of the accepted jobs plus the total penalty of the rejected jobs. We give an on-line algorithm for the problem with competitive ratio 1/2(2 + √3) ≈ 1.86602.

  17. Directions for Future Research in On-line Distance Education

    OpenAIRE

    Alaa SADIK

    2015-01-01

    Although institutions have invested much in developing on-line environments or using already established commercial platforms, only few studies have been conducted to investigate the effectiveness of on-line courses based on empirical data (Jung and Rha, 2000). A review of the literature conducted in this study showed that most of online learning studies investigated the effectiveness of Web-based interaction or Internet conferencing on learning, not the entire learning environment. Even in t...

  18. An On-line Ferrograph for Monitoring Machine Wear

    Institute of Scientific and Technical Information of China (English)

    L(U) Xiao-jun; JING Min-qing; XIE You-bai

    2005-01-01

    In order to improve an on-line ferrograph, this paper simulates a three dimensional magnetic field distribution of an electromagnet, builds a sinking motion model of a wear particle, and investigates the motion law of wear particles under two different conditions. Both numeric results and experimental results show that the on-line ferrograph is capable of monitoring machine wear conditions by measuring the concentration and size distribution of wear particles in lubricating oil.

  19. Quantitative microbial ecology through stable isotope probing.

    Science.gov (United States)

    Hungate, Bruce A; Mau, Rebecca L; Schwartz, Egbert; Caporaso, J Gregory; Dijkstra, Paul; van Gestel, Natasja; Koch, Benjamin J; Liu, Cindy M; McHugh, Theresa A; Marks, Jane C; Morrissey, Ember M; Price, Lance B

    2015-11-01

    Bacteria grow and transform elements at different rates, and as yet, quantifying this variation in the environment is difficult. Determining isotope enrichment with fine taxonomic resolution after exposure to isotope tracers could help, but there are few suitable techniques. We propose a modification to stable isotope probing (SIP) that enables the isotopic composition of DNA from individual bacterial taxa after exposure to isotope tracers to be determined. In our modification, after isopycnic centrifugation, DNA is collected in multiple density fractions, and each fraction is sequenced separately. Taxon-specific density curves are produced for labeled and nonlabeled treatments, from which the shift in density for each individual taxon in response to isotope labeling is calculated. Expressing each taxon's density shift relative to that taxon's density measured without isotope enrichment accounts for the influence of nucleic acid composition on density and isolates the influence of isotope tracer assimilation. The shift in density translates quantitatively to isotopic enrichment. Because this revision to SIP allows quantitative measurements of isotope enrichment, we propose to call it quantitative stable isotope probing (qSIP). We demonstrated qSIP using soil incubations, in which soil bacteria exhibited strong taxonomic variations in (18)O and (13)C composition after exposure to [(18)O]water or [(13)C]glucose. The addition of glucose increased the assimilation of (18)O into DNA from [(18)O]water. However, the increase in (18)O assimilation was greater than expected based on utilization of glucose-derived carbon alone, because the addition of glucose indirectly stimulated bacteria to utilize other substrates for growth. This example illustrates the benefit of a quantitative approach to stable isotope probing.

  20. On-line Excited-State Laser Spectroscopy of Trapped Short-Lived Ra$^+$ Ions

    CERN Document Server

    Versolato, O O; Wansbeek, L W; Berg, J E van den; van der Hoek, D J; Jungmann, K; Kruithof, W L; Onderwater, C J G; Sahoo, B K; Santra, B; Shidling, P D; Timmermans, R G E; Willmann, L; Wilschut, H W

    2010-01-01

    As an important step towards an atomic parity violation experiment in one single trapped Ra$^+$ ion, laser spectroscopy experiments were performed with on-line produced short-lived $^{212,213,214}$Ra$^+$ ions. The isotope shift of the $6\\,^2$D$_{3/2}$\\,-\\,$7\\,^2$P$_{1/2}$ and $6\\,^2$D$_{3/2}$\\,-\\,$7\\,^2$P$_{3/2}$ transitions and the hyperfine structure constant of the $7\\,^2$S$_{1/2}$ and $6\\,^2$D$_{3/2}$ states in $^{213}$Ra$^+$ were measured. These values provide a benchmark for the required atomic theory. A lower limit of $232(4)$ ms for the lifetime of the metastable $6\\,^2$D$_{5/2}$ state was measured by optical shelving.

  1. A commercial elemental on-line coal analyzer using pulsed neutrons

    Science.gov (United States)

    Belbot, Michael; Vouvopoulos, George; Paschal, Jonathan

    2001-07-01

    Because of its heterogeneity and the delay involved, traditional laboratory analysis of coal samples does not allow real time control of coal bulk parameters. Large excursions in important parameters (such as sulfur or calorific content) can be expensive and can be avoided with an on-line coal analyzer. The system that we developed utilizes nuclear reactions produced from fast and thermal neutrons and from neutron activation producing isotopes with half-lives longer than a few seconds. Characteristic gamma rays detected with BGO (bismuth germanate) detectors are used for the identification of the various chemical elements. The main features of the analyzer are elemental self-calibration independent of the coal seam; better accuracy in the determination of elements such as carbon, oxygen, and sodium; and diminished radiation risk. A prototype coal analyzer has been built and the first commercial model is currently being developed.

  2. Nickel isotopes and methanogens

    Science.gov (United States)

    Neubeck, A.; Ivarsson, M.

    2013-12-01

    Methanogens require Ni for their growth and as a consequence the microbial fractionation of Ni isotopes can be used as a biomarker for activity of methanogenic communities1. Anaerobic laboratory experiments was performed using methanogens to investigate methanogenic growth in a modified nutrient media2 with olivine Fo91 (5g/l) added as an additional mineral nutrient source and as the only H2 provider. One of the investigated methanogens showed an increased growth in the experiments with added olivine. There were also a close relationship between the mobilized Ni and the growth of the methanogen. Ni is an element that previously has been neglected in the study of fossilized microorganisms and their interaction with mineral substrates and, thus, there are no records or published data of Ni in association with microfossils. However, we have detected enrichments of Ni in fossilized microorganisms and ichno-fossils, respectively, from three separate locations. Ni is not present in the host rock in any of the samples. Thus, Ni is present in association with fossilized microorganisms from environments and more extensive analysis is required to understand the magnitude, uptake, preservation and fractionation of Ni in microfossils. In order to analyze Ni isotope fractionation from microbe-mineral interaction, we plan to use a high-resolution Laser-Ablation Time-of-Flight Mass Spectrometer (LMS)3. In situ profile ablation will provide detailed and localized data on fractionation patterns between microfossils and their host rock. Also, this technique will allow us to identify the change in Ni isotopic fractionation in rock samples caused by abiotic and biogenic processes in a faster and easier way and with less risk for contamination compared to the wet chemistry analyses of Ni isotopes. 1. Cameron, V., Vance, D., Archer, C. & House, C. H. A biomarker based on the stable isotopes of nickel. Proceedings of the National Academy of Sciences 106, 10944-10948 (2009). 2. Schn

  3. CENTRIFUGAL SEPARATORS

    Science.gov (United States)

    Skarstrom, C.

    1959-03-10

    A centrifugal separator is described for separating gaseous mixtures where the temperature gradients both longitudinally and radially of the centrifuge may be controlled effectively to produce a maximum separation of the process gases flowing through. Tbe invention provides for the balancing of increases and decreases in temperature in various zones of the centrifuge chamber as the result of compression and expansions respectively, of process gases and may be employed effectively both to neutralize harmful temperature gradients and to utilize beneficial temperaturc gradients within the centrifuge.

  4. Stable isotope customer list and summary of shipments - FY 1983

    Energy Technology Data Exchange (ETDEWEB)

    Davis, W.C. (comp.)

    1983-12-01

    This compilation is published as an aid to those concerned with the separation and sale of stable isotopes. The information is divided into four sections: (1) alphabetical list of domestic and foreign customers, showing the stable isotopes purchased during the fiscal year; (2) alphabetical list of isotopes, cross-referenced to customer numbers and divided into domestic and foreign categories; (3) alphabetical list of states and countries, cross-referenced to customer numbers and indicating geographical concentrations of isotope users; and (4) tabulation of the shipments, quantities, and dollars for domestic, foreign, and project categories for each isotope.

  5. Stable Isotope Customer List and Summary of Shipments. FY 1985

    Energy Technology Data Exchange (ETDEWEB)

    Tracy, J. G. [comp.

    1985-11-01

    This compilation is published as an aid to those concerned with the separation and sale of stable isotopes. The information is divided into four sections: (1) alphabetical list of domestic and foreign customers, showing the stable isotopes purchased during the fiscal year; (2) alphabetical list of isotopes, cross-referenced to customer numbers and divided into domestic and foreign categories; (3) alphabetical list of states and countries, cross-referenced to customer numbers and indicating geographical concentrations of isotope users; and (4) tabulation of the shipments, quantities, and dollars for domestic, foreign, and project categories for each isotope.

  6. Miniaturization of Separation Systems and Its Applications

    Institute of Scientific and Technical Information of China (English)

    Yoshihiro Saito

    2003-01-01

    Development of miniaturized separation system consisted of microscale extraction and liquid phase separation processes has been reviewed.Various types of novel bonded stationary phases have been developed on the basis of the systematic analysis for the retention behavior of polycyclic aromatic hydrocarbons on experimentally synthesized phases. In this review, the miniaturization of microscale sample preparation technique and the effective on-line coupling to microcolumn liquid phase separations are also described especially focusing on the approach by the author's group. The novel use of synthetic polymer filaments as the stationary phase and extraction media in those microscale separation systems will be introduced along with the applications in gas chromatographic separation.

  7. Beneficial uses and production of isotopes

    CERN Document Server

    2001-01-01

    Isotopes, radioactive and stable, are used worldwide in various applications related to medical diagnosis or care, industry and scientific research. More than fifty countries have isotope production or separation facilities operated for domestic supply, and sometimes for international markets. This publication provides up-to-date information on the current status of, and trends in, isotope uses and production. It also presents key issues, conclusions and recommendations, which will be of interest to policy makers in governmental bodies, scientists and industrial actors in the field.

  8. Hafnium isotope stratigraphy of ferromanganese crusts

    Science.gov (United States)

    Lee, D.-C.; Halliday, A.N.; Hein, J.R.; Burton, K.W.; Christensen, J.N.; Gunther, D.

    1999-01-01

    A Cenozoic record of hafnium isotopic compositions of central Pacific deep water has been obtained from two ferromanganese crusts. The crusts are separated by more than 3000 kilometers but display similar secular variations. Significant fluctuations in hafnium isotopic composition occurred in the Eocene and Oligocene, possibly related to direct advection from the Indian and Atlantic oceans. Hafnium isotopic compositions have remained approximately uniform for the past 20 million years, probably reflecting increased isolation of the central Pacific. The mechanisms responsible for the increase in 87Sr/86Sr in seawater through the Cenozoic apparently had no effect on central Pacific deep-water hafnium.

  9. Simulation and Optimization of Stable Isotope 18O Separation by Cascade Distillation%级联生产稳定同位素18O的模拟优化研究

    Institute of Scientific and Technical Information of China (English)

    姜永悦; 陈玉岩; 秦川江; 刘严; 谷宏森

    2011-01-01

    本工作利用已有的四塔级联设计方案,通过采用均匀设计方法对操作参数进行优化,并利用二项式逐步回归求取模型方程,同时利用遗传算法对模型进行了优化设计,综合分析了不同进料量及级间流量对18O产品丰度的影响,得到产品18O的丰度与进料量及级间流量和热量消耗与进料量及级间流量的数学关系式,并得出进料量与级间流量的单因素响应图.本研究采用的模拟优化方法可应用到18O的产业化生产及推广至传统精馏过程的优化设计中.%The research about started from the plan of four cascade towers desgin was carried. Firstly, the method of experiment design was using uniform design. Then the incidence formula with the method of binomial stepwise regression was gotten. Last, the optimal operation conditions were gotten by using the method of genetic algorithm. Considering comprehensive factors of drawn from feed rate and from flow rates between cascade column, conclusions were reached on the study of the impact on the abundance of the isotope 18O. Finally, the incidence formula between the abundance of the isotope 18O and four operating variables were gotten. Also the incidence formula between heat consumption of the isotope 18O and four operating variables were gotten. Besides, single factor response diagram of four factors were shown at last. The results showed that the method of simulation and optimization could be applied to 18O industrial design and would be popular in traditional distillation process to realize optimization design.

  10. 离子液体/苯并15-冠-5浸渍XAD-7树脂萃取分离锂同位素%Extraction Separation of Lithium Isotopes by Using XAD-7 Resins Impregnated With Ionic Liquid and Benzo-15-Crown-5

    Institute of Scientific and Technical Information of China (English)

    顾玲; 孙晓利; 任冬红; 邱丹; 顾志国; 李在均

    2015-01-01

    Imidazolium-type ionic liquid ([C8 mim][BF4 ],[C8 mim][PF6 ]and [C8 mim] [(SO2 CF3 )2 N])and benzo-15-crown-5 were immobilized on XAD-7 resin to obtain the im-pregnated resin for lithium isotopes separation.IR and SEM characterizations of the impreg-nated resins indicate that ionic liquids and benzo-15-crown-5 are immobilized in the resins successfully and the thermal analysis indicates that the materials are thermally stable.The optimum E was obtained in the initial solution at pH=5.55.The larger extraction percenta-ges and separation factors values were obtained from LiSCN solution and CF3 COOLi solu-tion,respectively.The maximum single-stage isotopes separation factor of 6 Li/7 Li is up to 1.045±0.002.The equilibrium time of extraction is attained in 2.5-3 h.The thermodynamic parameters of the system were presented and revealed that the extraction reaction was a spontaneous process and the temperature had slight influence on the extraction separation of lithium isotopes.The mechanism of extraction system show that 6 Li enriches in the solid phase and 7 Li concentrates in the aqueous phase.The impregnated resins can be regenerated and reused for lithium isotopes separation.%以 XAD-7树脂为支撑担体制备了含有三种不同咪唑型离子液体([C8 mim][BF4]、[C8 mim][PF6]、[C8 mim][(SO2 CF3)2 N])和萃取剂(苯并15-冠-5)的浸渍树脂,并用于锂同位素的萃取分离。浸渍树脂的红外和扫描电镜表征表明,离子液体成功负载到了树脂上;热重分析表明,该浸渍树脂具有良好的热稳定性。在水相初始 pH=5.55时,浸渍树脂具有最佳萃取率。浸渍树脂在 LiSCN 溶液中具有较高的萃取率,而在CF3 COOLi 溶液中呈现较大的单级分离因子,最大单级分离因子达到1.045±0.002。浸渍树脂的萃取平衡时间为2.5~3 h。萃取热力学研究表明,该反应为自发过程,温度对体系的影响较小。6 Li 富集于固相,7 Li 富集在水相。该系列浸渍树脂易于再生,可循环使用。

  11. Sport Management Taught On-Line: A Discussion

    Directory of Open Access Journals (Sweden)

    William F. Stier Jr

    2009-01-01

    Full Text Available An introduction to the world of on-line courses (distance education/learning is presented. In addition, the world of on-line learning, as it pertains to sport management, is examined within the framework of (a pedagogy, (b finances,(c assessment, and (d choosing to transition from the traditional classroom to on-line learning. Pertinent points relative to each of the four categories are presented from the literature. In an effort to stimulate thought and discussion to the subject of on-line learning for sport management programs/courses the authors provide their reactions to the literature points by presenting their comments/reactions from a sport management perspective. Sport management professors and administrators are encouraged to critically examine the feasibility of such on-line courses (distance education/learning within their own curricula while maintaining an appropriate framework revolving around sound theoretical instructional strategies, methods as well as appropriate use of instructional tools, including but not limited to, computersand the WWW.

  12. High-Throughput Proteomics Using High Efficiency Multiple-Capillary Liquid Chromatography With On-Line High-Performance ESI FTICR Mass Spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Yufeng (BATTELLE (PACIFIC NW LAB)); Tolic, Nikola (BATTELLE (PACIFIC NW LAB)); Zhao, Rui (ASSOC WESTERN UNIVERSITY); Pasa Tolic, Ljiljana (BATTELLE (PACIFIC NW LAB)); Li, Lingjun (Illinois Univ Of-Urbana/Champa); Berger, Scott J.(ASSOC WESTERN UNIVERSITY); Harkewicz, Richard (BATTELLE (PACIFIC NW LAB)); Anderson, Gordon A.(BATTELLE (PACIFIC NW LAB)); Belov, Mikhail E.(BATTELLE (PACIFIC NW LAB)); Smith, Richard D.(BATTELLE (PACIFIC NW LAB))

    2000-12-01

    We report on the design and application of a high-efficiency multiple-capillary liquid chromatography (LC) system for high-throughput proteome analysis. The multiple-capillary LC system was operated at the pressure of 10,000 psi using commercial LC pumps to deliver the mobile phase and newly developed passive feedback valves to switch the mobile phase flow and introduce samples. The multiple-capillary LC system was composed of several serially connected dual-capillary column devices. The dual-capillary column approach was designed to eliminate the time delay for regeneration (or equilibrium) of the capillary column after its use under the mobile phase gradient condition (i.e. one capillary column was used in separation and the other was washed using mobile phase A). The serially connected dual-capillary columns and ESI sources were operated independently, and could be used for either''backup'' operation or with other mass spectrometer(s). This high-efficiency multiple-capillary LC system uses switching valves for all operations and is highly amenable to automation. The separations efficiency of dual-capillary column device, optimal capillary dimensions (column length and packed particle size), suitable mobile phases for electrospray, and the capillary re-generation were investigated. A high magnetic field (11.5 tesla) Fourier transform ion cyclotron resonance (FTICR) mass spectrometer was coupled on-line with this high-efficiency multiple-capillary LC system through an electrospray ionization source. The capillary LC provided a peak capacity of {approx}600, and the 2-D capillary LC-FTICR provided a combined resolving power of > 6 x 10 7 polypeptide isotopic distributions. For yeast cellular tryptic digests, > 100,000 polypeptides were typically detected, and {approx}1,000 proteins can be characterized in a single run.

  13. Stable isotope studies

    Energy Technology Data Exchange (ETDEWEB)

    Ishida, T.

    1992-01-01

    The research has been in four general areas: (1) correlation of isotope effects with molecular forces and molecular structures, (2) correlation of zero-point energy and its isotope effects with molecular structure and molecular forces, (3) vapor pressure isotope effects, and (4) fractionation of stable isotopes. 73 refs, 38 figs, 29 tabs.

  14. On-line Payment System Survey – eCash

    Directory of Open Access Journals (Sweden)

    Marius Popa

    2009-12-01

    Full Text Available The paper presents the main aspects regarding an on-line payment system. Some characteristics of such system are presented and an existing system is analyzed. On its fundamental sense, the electronic commerce is a concept that represents the purchase and sale process or exchange of products, services, information, using o computer network, inclusively the Internet. In the most part of the cases, the electronic commerce imply on-line payments that lead to creation of some kinds of electronic money and some specific payment systems. There are described the some electronic payment mechanisms and the architecture and the functions of the on-line payment system E-Cash are depicted.

  15. A Hybrid On-line Verification Method of Relay Setting

    Science.gov (United States)

    Gao, Wangyuan; Chen, Qing; Si, Ji; Huang, Xin

    2017-05-01

    Along with the rapid development of the power industry, grid structure gets more sophisticated. The validity and rationality of protective relaying are vital to the security of power systems. To increase the security of power systems, it is essential to verify the setting values of relays online. Traditional verification methods mainly include the comparison of protection range and the comparison of calculated setting value. To realize on-line verification, the verifying speed is the key. The verifying result of comparing protection range is accurate, but the computation burden is heavy, and the verifying speed is slow. Comparing calculated setting value is much faster, but the verifying result is conservative and inaccurate. Taking the overcurrent protection as example, this paper analyses the advantages and disadvantages of the two traditional methods above, and proposes a hybrid method of on-line verification which synthesizes the advantages of the two traditional methods. This hybrid method can meet the requirements of accurate on-line verification.

  16. Strengthening weak ties through on-line gaming

    DEFF Research Database (Denmark)

    Sudzina, Frantisek; Razmerita, Liana Virginia; Kirchner, Kathrin

    On-line gaming became widespread in the last couple of years. The aim of the research presented in the paper is to figure out to what extent does game playing helps to strengthen weak ties and what additional factors influence this process. The approach is rather exploratory – some factors...... are grounded in theory, some are new. These factors are age, gender, place of origin, number of their Facebook connections (friends in Facebook terminology), the amount of time they are on Facebook, the amount of time they keep the Facebook site open, the amount of time they play on-line games, and the reasons...... for starting to play on-line games. Regarding the latter, we chose to focus only on escapist reasons....

  17. On-Line Voltage Stability Assessment based on PMU Measurements

    DEFF Research Database (Denmark)

    Garcia-Valle, Rodrigo; P. Da Silva, Luiz C.; Nielsen, Arne Hejde

    2009-01-01

    through statistic analysis. During the off-line analysis, a memory of high-risk situations following a pre-defined voltage stability criterion is obtained. Thereafter, basic statistics analyses are applied resulting in the definition of voltage regions. During on-line operation, voltage magnitudes......This paper presents a method for on-line monitoring of risk voltage collapse based on synchronised phasor measurement. As there is no room for intensive computation and analysis in real-time, the method is based on the combination of off-line computation and on-line monitoring, which are correlated...... of critical buses obtained by phasor measurements are monitored in relation to the risk regions. Comprehensive studies demonstrate that the proposed method could assist operators to avoid voltage collapse events, by taking preventive or emergency actions....

  18. On-line tribochemical strengthening of gear surface

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    It has been found that under favorable friction conditions some antiwear elements inlubricating additives can permeate into subsurface of metal which can strengthens the friction sur-faces and improves anti-wear capacity of frication pairs. It is in many ways similar to chemical heattreatment. A new concept, technology of on-line strengthening, was logically put forward. Based oncurrent gear surface treatment technology, the on-line strengthen of gear surface is proposed. Itsdesign method is established. Based on it, the on-line strengthen of gear is achieved on CL-100gear test machine. A new method is put forward for strengthen treatment of gear surface. Andthree kinds of surface film were suggested.

  19. Why do People Stop Playing On-Line Games?

    DEFF Research Database (Denmark)

    Sudzina, Frantisek; Razmerita, Liana

    2012-01-01

    The recent initial public offering of shares of Zynga, probably the most important on-line game provider, drew interest of potential investors but also of general public to their business model. What the most interested people learned so far is that if Zynga had not changed their accounting...... practice, they would be in red numbers for several months already. This is most likely caused by people stopping to play their games. This paper provides an estimate of what proportion of people, who played on-line games, already stopped playing them. Additionally, it analyzed the reasons why people...

  20. On-Line Generation of 3D-Waves

    DEFF Research Database (Denmark)

    Frigaard, Peter

    1992-01-01

    The paper describes the technique of filtering white noise for on-line generation of 3D-waves on a small computer in the laboratory. The wave generation package is implemented and tested in the 3D-wave basin at the University of Aalborg.......The paper describes the technique of filtering white noise for on-line generation of 3D-waves on a small computer in the laboratory. The wave generation package is implemented and tested in the 3D-wave basin at the University of Aalborg....

  1. On-line measurement of heat of combustion

    Science.gov (United States)

    Chaturvedi, S. K.; Chegini, H.

    1988-01-01

    An experimental method for an on-line measurement of heat of combustion of a gaseous hydrocarbon fuel mixture of unknown composition is developed. It involves combustion of a test gas with a known quantity of air to achieve a predetermined oxygen concentration level in the combustion products. This is accomplished by a feedback controller which maintains the gas volumetric flow rate at a level consistent with the desired oxygen concentration in the products. The heat of combustion is determined from a known correlation with the gas volumetric flow rate. An on-line microcomputer accesses the gas volumetric flow data, and displays the heat of combustion values at desired time intervals.

  2. 5th Computer Science On-line Conference

    CERN Document Server

    Senkerik, Roman; Oplatkova, Zuzana; Silhavy, Petr; Prokopova, Zdenka

    2016-01-01

    This volume is based on the research papers presented in the 5th Computer Science On-line Conference. The volume Artificial Intelligence Perspectives in Intelligent Systems presents modern trends and methods to real-world problems, and in particular, exploratory research that describes novel approaches in the field of artificial intelligence. New algorithms in a variety of fields are also presented. The Computer Science On-line Conference (CSOC 2016) is intended to provide an international forum for discussions on the latest research results in all areas related to Computer Science. The addressed topics are the theoretical aspects and applications of Computer Science, Artificial Intelligences, Cybernetics, Automation Control Theory and Software Engineering.

  3. On-line Batch Process Monitoring and Diagnosing Based on Fisher Discriminant Analysis

    Institute of Scientific and Technical Information of China (English)

    ZHAO Xu; SHAO Hui-he

    2006-01-01

    A new on-line batch process monitoring and diagnosing approach based on Fisher discriminant analysis (FDA) was proposed. This method does not need to predict the future observations of variables, so it is more sensitive to fault detection and stronger implement for monitoring. In order to improve the monitoring performance,the variables trajectories of batch process are separated into several blocks. The key to the proposed approach for on-line monitoring is to calculate the distance of block data that project to low-dimension Fisher space between new batch and reference batch. Comparing the distance with the predefine threshold, it can be considered whether the batch process is normal or abnormal. Fault diagnosis is performed based on the weights in fault direction calculated by FDA. The proposed method was applied to the simulation model of fed-batch penicillin fermentation and the results were compared with those obtained using MPCA. The simulation results clearly show that the on-line monitoring method based on FDA is more efficient than the MPCA.

  4. HOPE: An On-Line Piloted Handling Qualities Experiment Data Book

    Science.gov (United States)

    Jackson, E. B.; Proffitt, Melissa S.

    2010-01-01

    A novel on-line database for capturing most of the information obtained during piloted handling qualities experiments (either flight or simulated) is described. The Hyperlinked Overview of Piloted Evaluations (HOPE) web application is based on an open-source object-oriented Web-based front end (Ruby-on-Rails) that can be used with a variety of back-end relational database engines. The hyperlinked, on-line data book approach allows an easily-traversed way of looking at a variety of collected data, including pilot ratings, pilot information, vehicle and configuration characteristics, test maneuvers, and individual flight test cards and repeat runs. It allows for on-line retrieval of pilot comments, both audio and transcribed, as well as time history data retrieval and video playback. Pilot questionnaires are recorded as are pilot biographies. Simple statistics are calculated for each selected group of pilot ratings, allowing multiple ways to aggregate the data set (by pilot, by task, or by vehicle configuration, for example). Any number of per-run or per-task metrics can be captured in the database. The entire run metrics dataset can be downloaded in comma-separated text for further analysis off-line. It is expected that this tool will be made available upon request

  5. On-line coupling of supercritical fluid extraction and chromatographic techniques.

    Science.gov (United States)

    Sánchez-Camargo, Andrea Del Pilar; Parada-Alfonso, Fabián; Ibáñez, Elena; Cifuentes, Alejandro

    2017-01-01

    This review summarizes and discusses recent advances and applications of on-line supercritical fluid extraction coupled to liquid chromatography, gas chromatography, and supercritical fluid chromatographic techniques. Supercritical fluids, due to their exceptional physical properties, provide unique opportunities not only during the extraction step but also in the separation process. Although supercritical fluid extraction is especially suitable for recovery of non-polar organic compounds, this technique can also be successfully applied to the extraction of polar analytes by the aid of modifiers. Supercritical fluid extraction process can be performed following "off-line" or "on-line" approaches and their main features are contrasted herein. Besides, the parameters affecting the supercritical fluid extraction process are explained and a "decision tree" is for the first time presented in this review work as a guide tool for method development. The general principles (instrumental and methodological) of the different on-line couplings of supercritical fluid extraction with chromatographic techniques are described. Advantages and shortcomings of supercritical fluid extraction as hyphenated technique are discussed. Besides, an update of the most recent applications (from 2005 up to now) of the mentioned couplings is also presented in this review.

  6. Comparing the happiness effects of real and on-line friends.

    Directory of Open Access Journals (Sweden)

    John F Helliwell

    Full Text Available A recent large Canadian survey permits us to compare face-to-face ('real-life' and on-line social networks as sources of subjective well-being. The sample of 5,000 is drawn randomly from an on-line pool of respondents, a group well placed to have and value on-line friendships. We find three key results. First, the number of real-life friends is positively correlated with subjective well-being (SWB even after controlling for income, demographic variables and personality differences. Doubling the number of friends in real life has an equivalent effect on well-being as a 50% increase in income. Second, the size of online networks is largely uncorrelated with subjective well-being. Third, we find that real-life friends are much more important for people who are single, divorced, separated or widowed than they are for people who are married or living with a partner. Findings from large international surveys (the European Social Surveys 2002-2008 are used to confirm the importance of real-life social networks to SWB; they also indicate a significantly smaller value of social networks to married or partnered couples.

  7. Separative power of an optimised concurrent gas centrifuge

    Energy Technology Data Exchange (ETDEWEB)

    Bogovalov, Sergey; Boman, Vladimir [National Research Nuclear University (MEPHI), Moscow (Russian Federation)

    2016-06-15

    The problem of separation of isotopes in a concurrent gas centrifuge is solved analytically for an arbitrary binary mixture of isotopes. The separative power of the optimised concurrent gas centrifuges for the uranium isotopes equals to δU = 12.7 (V/700 m/s)2(300 K/T)(L/1 m) kg·SWU/yr, where L and V are the length and linear velocity of the rotor of the gas centrifuge and T is the temperature. This equation agrees well with the empirically determined separative power of optimised counter-current gas centrifuges.

  8. Separative Power of an Optimised Concurrent Gas Centrifuge

    Directory of Open Access Journals (Sweden)

    Sergey Bogovalov

    2016-06-01

    Full Text Available The problem of separation of isotopes in a concurrent gas centrifuge is solved analytically for an arbitrary binary mixture of isotopes. The separative power of the optimised concurrent gas centrifuges for the uranium isotopes equals to δU = 12.7 (V/700 m/s2(300 K/T(L/1 m kg·SWU/yr, where L and V are the length and linear velocity of the rotor of the gas centrifuge and T is the temperature. This equation agrees well with the empirically determined separative power of optimised counter-current gas centrifuges.

  9. Isotopically Modified Molybdenum: Production for Application in Nuclear Energy

    Science.gov (United States)

    Smirnov, A. Yu.; Bonarev, A. K.; Sulaberidze, G. A.; Borisevich, V. D.; Kulikov, G. G.; Shmelev, A. N.

    The possibility to use the isotopically modified molybdenum as a constructive material for the fuel rods of light water and fast reactors is discussed. The calculations demonstrate that the isotopically modified molybdenum with an average neutron absorption cross-section comparable to that of zirconium can be obtained with the reasonable for practice cost by a cascade of gas centrifuges, specially designed for separation of non-uranium isotopes.

  10. Calcium isotopes in wine

    Science.gov (United States)

    Holmden, C. E.

    2011-12-01

    The δ 44/40Ca values of bottled wine vary between -0.76% to -1.55% on the seawater scale and correlate weakly with inverse Ca concentration and Mg/Ca ratio, such that the lowest δ 44/40Ca values have the highest Ca concentrations and lowest Mg/Ca ratios. The correlation is notable in the sense that the measured wines include both whites and reds sampled from different wine growing regions of the world, and cover a wide range of quality. Trends among the data yield clues regarding the cause of the observed isotopic fractionation. White wines, and wines generally perceived to be of lower quality, have lower δ 44/40Ca values compared to red wines and wines of generally perceived higher quality. Quality was assessed qualitatively through sensory evaluation, price, and scores assigned by critics. The relationship between δ 44/40Ca and wine quality was most apparent when comparing wines of one varietal from one producer from the same growing region. In the vineyard, wine quality is related to factors such as the tonnage of the crop and the ripeness of the grapes at the time of harvesting, the thickness of the skins for reds, the age of the vines, as well as the place where the grapes were grown (terroir). Quality is also influenced by winemaking practices such as fermentation temperature, duration of skin contact, and barrel ageing. Accordingly, the relationship between δ 44/40Ca and wine quality may originate during grape ripening in the vineyard or during winemaking in the cellar. We tested the grape ripening hypothesis using Merlot grapes sampled from a vineyard in the Okanagan, British Columbia, using sugar content (degrees Brix) as an indicator of ripeness. The grapes were separated into pulp, skin, and pip fractions and were analyzed separately. Thus far, there is no clear evidence for a systematic change in δ 44/40Ca values associated with progressive ripening of grapes in the vineyard. On the day of harvesting, the δ 44/40Ca value of juice squeezed from

  11. On-Line Learning and the Implications for School Design

    Science.gov (United States)

    Stack, Greg

    2011-01-01

    "Disrupting Class," published in 2008, is the story of how disruptive innovation, innovation that changes the business model organizations, will fundamentally change the American school system. The book's most startling prediction is that half of all high school classes will be on-line by 2019. In considering these predictions, the author began to…

  12. On-line probabilistic classification with particle filters

    DEFF Research Database (Denmark)

    Højen-Sørensen, Pedro; de Freitas, N.; Fog, Torben L.

    2000-01-01

    We apply particle filters to the problem of on-line classification with possibly overlapping classes. This allows us to compute the probabilities of class membership as the classes evolve. Although we adopt neural network classifiers, the work can be extended to any other parametric classification...

  13. Personal Assistant for onLine Services: Addressing human factors

    NARCIS (Netherlands)

    Lindenberg, J.; Nagata, S.F.; Neerincx, M.A.

    2003-01-01

    The Personal Assistant for onLine Services (PALS) project aims at substantially improving the user experience of mobile internet services. It focuses on a generic solution: a personal assistant, which attunes the interaction to the momentary user needs and use context (e.g. adjusting the

  14. Efficiently Building On-line Tools for Distributed Heterogeneous Environments

    Directory of Open Access Journals (Sweden)

    Günther Rackl

    2002-01-01

    Full Text Available Software development is getting more and more complex, especially within distributed middleware-based environments. A major drawback during the overall software development process is the lack of on-line tools, i.e. tools applied as soon as there is a running prototype of an application. The MIMO MIddleware MOnitor provides a solution to this problem by implementing a framework for an efficient development of on-line tools. This paper presents a methodology for developing on-line tools with MIMO. As an example scenario, we choose a distributed medical image reconstruction application, which represents a test case with high performance requirements. Our distributed, CORBA-based application is instrumented for being observed with MIMO and related tools. Additionally, load balancing mechanisms are integrated for further performance improvements. As a result, we obtain an integrated tool environment for observing and steering the image reconstruction application. By using our rapid tool development process, the integration of on-line tools shows to be very convenient and enables an efficient tool deployment.

  15. Developing an On-Line Interactive Health Psychology Module

    Science.gov (United States)

    Upton, Dominic; Cooper, Carol

    2006-01-01

    On-line teaching material in health psychology was developed which ensured a range of students could access appropriate material for their course and level of study. This material has been developed around the concept of smaller "content chunks" which can be combined into whole units of learning (topics), and ultimately, a module. On the basis of…

  16. Why do People Stop playing On-Line Games?

    DEFF Research Database (Denmark)

    Sudzina, Frantisek; Razmerita, Liana

    2012-01-01

    The recent initial public offering of shares of Zynga, probably the most important on-line game provider, drew interest of potential investors but also of general public to their business model. What the most interested people learned so far is that if Zynga had not changed their accounting...

  17. On-line fuzzy logic control of tube bending

    Science.gov (United States)

    Lieh, Junghsen; Li, Wei Jie

    2005-11-01

    This paper describes the simulation and on-line fuzzy logic control of tube bending. By combining elasticity and plasticity theories, a conventional model was developed. The results from simulation were compared with those obtained from testing. The experimental data reveal that there exists certain level of uncertainty and nonlinearity in tube bending, and its variation could be significant. To overcome this, a on-line fuzzy logic controller with self-tuning capabilities was designed. The advantages of this on-line system are (1) its computational requirement is simple in comparison with more algorithmic-based controllers, and (2) the system does not need prior knowledge of material characteristics. The device includes an AC motor, a servo controller, a forming mechanism, a 3D optical sensor, and a microprocessor. This automated bending machine adopts primary and secondary errors between the actual response and desired output to conduct on-line rule reasoning. Results from testing show that the spring back angle can be effectively compensated by the self- tuning fuzzy system in a real-time fashion.

  18. The dynamics of on-line principal component analysis

    NARCIS (Netherlands)

    Biehl, M.; Schlösser, E.

    1998-01-01

    The learning dynamics of an on-line algorithm for principal component analysis is described exactly in the thermodynamic limit by means of coupled ordinary differential equations for a set of order parameters. It is demonstrated that learning is delayed significantly because existing symmetries amon

  19. On-Line Learning and the Implications for School Design

    Science.gov (United States)

    Stack, Greg

    2011-01-01

    "Disrupting Class," published in 2008, is the story of how disruptive innovation, innovation that changes the business model organizations, will fundamentally change the American school system. The book's most startling prediction is that half of all high school classes will be on-line by 2019. In considering these predictions, the author began to…

  20. Specialization processes in on-line unsupervised learning

    NARCIS (Netherlands)

    Biehl, M.; Freking, A.; Reents, G.; Schlösser, E.

    1998-01-01

    From the recent analysis of supervised learning by on-line gradient descent in multilayered neural networks it is known that the necessary process of student specialization can be delayed significantly. We demonstrate that this phenomenon also occurs in various models of unsupervised learning. A sol

  1. A New On-Line Resource for Psycholinguistic Studies

    Science.gov (United States)

    Szekely, Anna; Jacobsen, Thomas; D'Amico, Simona; Devescovi, Antonella; Andonoa, Elena; Herron, Daniel; Lu, Ching Ching; Pechmann, Thomas; Pleh, Csaba; Wicha, Nicole; Federmeier, Kara; Gerdjikova, Irina; Gutierrez, Gabriel; Hung, Daisy, Hsu, Jeanne; Iyer, Gowri; Kohnert, Kathryn; Mehotcheva, Teodora; Orozco-Figueroa, Araceli; Tzeng, Angela; Tzeng, Ovid; Arevalo, Analia; Vargha, Andras; Butler, Andrew C.; Buffington, Robert; Bates, Elizabeth

    2004-01-01

    Picture naming is a widely used technique in psycholinguistic studies. Here, we describe new on-line resources that our project has compiled and made available to researchers on the world wide web at http://crl.ucsd.edu/~aszekely/ipnp/. The website provides access to a wide range of picture stimuli and related norms in seven languages. Picture…

  2. ADAPTIVE CONTEXT PROCESSING IN ON-LINE HANDWRITTEN CHARACTER RECOGNITION

    NARCIS (Netherlands)

    Iwayama, N.; Ishigaki, K.

    2004-01-01

    We propose a new approach to context processing in on-line handwritten character recognition (OLCR). Based on the observation that writers often repeat the strings that they input, we take the approach of adaptive context processing. (ACP). In ACP, the strings input by a writer are automatically

  3. The Lesson Observation On-Line (Evidence Portfolio) Platform

    Science.gov (United States)

    Cooper, David G.

    2015-01-01

    At a time when teacher training is being moved to school-based programmes it is important to engage in a research-informed dialogue about creating more distinctive, and cost-effective 21st century models of teacher training. Three years ago I began feasibility field testing the Lesson Observation On-line (Evidence Portfolio) Platform [LOOP]…

  4. On-line EM algorithm for the normalized gaussian network.

    Science.gov (United States)

    Sato, M; Ishii, S

    2000-02-01

    A normalized gaussian network (NGnet) (Moody & Darken, 1989) is a network of local linear regression units. The model softly partitions the input space by normalized gaussian functions, and each local unit linearly approximates the output within the partition. In this article, we propose a new on-line EMalgorithm for the NGnet, which is derived from the batch EMalgorithm (Xu, Jordan, &Hinton 1995), by introducing a discount factor. We show that the on-line EM algorithm is equivalent to the batch EM algorithm if a specific scheduling of the discount factor is employed. In addition, we show that the on-line EM algorithm can be considered as a stochastic approximation method to find the maximum likelihood estimator. A new regularization method is proposed in order to deal with a singular input distribution. In order to manage dynamic environments, where the input-output distribution of data changes over time, unit manipulation mechanisms such as unit production, unit deletion, and unit division are also introduced based on probabilistic interpretation. Experimental results show that our approach is suitable for function approximation problems in dynamic environments. We also apply our on-line EM algorithm to robot dynamics problems and compare our algorithm with the mixtures-of-experts family.

  5. On-Line Synthesis and Analysis by Mass Spectrometry

    Science.gov (United States)

    Bain, Ryan M.; Pulliam, Christopher J.; Raab, Shannon A.; Cooks, R. Graham

    2015-01-01

    In this laboratory experiment, students learn how to use ESI to accelerate chemical synthesis and to couple it with on-line mass spectrometry for structural analysis. The Hantzsch synthesis of symmetric 1,4-dihydropyridines is a classic example of a one-pot reaction in which multiple intermediates can serve to indicate the progress of the reaction…

  6. Investigating on-line pornography at the University of Johannesburg

    Directory of Open Access Journals (Sweden)

    P. Laughton

    2008-01-01

    Full Text Available The on-line user of today has access to a vast collection of information resources. In addition, the developments in Internet and Web technologies have made it even easier for surfers to anonymously get access to on-line pornography. The purpose of this research was to investigate the extent to which access to on-line pornography at the University of Johannesburg can be managed. For the empirical part of this research 1037 questionnaires were proportionally distributed to and completed by students on all five campuses of the university. The questionnaire consisted of four sections: biographical information; university computer facility usage; university acceptable use policy; and personal experience with university computer facilities. The gender distribution for the sample was almost even, with a total of 49,4% male participants and 50,6% female, with the largest grouping of respondents (61,6% aged between 19 years and 21 years. Of the respondents, 36,7% indicated that exposure to unsolicited pornography did not bother them. When asked to what extent students should have access to pornography, 60,5% stated 'None' while 32,6% believed that 'Restricted' access should be granted for research purposes and 6,9% believed that students should be granted 'Total' access to pornography. Results from the research will be used to manage access to on-line resources at the University of Johannesburg better.

  7. Investigating on-line pornography at the University of Johannesburg

    Directory of Open Access Journals (Sweden)

    P. Laughton

    2007-12-01

    Full Text Available The on-line user of today has access to a vast collection of information resources. In addition, the developments in Internet and Web technologies have made it even easier for surfers to anonymously get access to on-line pornography. The purpose of this research was to investigate the extent to which access to on-line pornography at the University of Johannesburg can be managed. For the empirical part of this research 1037 questionnaires were proportionally distributed to and completed by students on all five campuses of the university. The questionnaire consisted of four sections: biographical information; university computer facility usage; university acceptable use policy; and personal experience with university computer facilities. The gender distribution for the sample was almost even, with total of 49,4% male participants and 50,6% female, with the largest grouping of respondents(61,6% aged between 19 years and 21 years. Of the respondents, 36,7% indicated that exposure to unsolicited pornography did not bother them. When asked to what extent students should have access to pornography, 60,5% stated 'None' while 32,6% believed that 'Restricted' access should be granted for research purposes and 6,9% believed that students should be granted 'Total' access to pornography. Results from the research will be used to manage access to on-line resources at the University of Johannesburg better.

  8. On-Line NDE for Advanced Reactor Designs

    Science.gov (United States)

    Nakagawa, N.; Inanc, F.; Thompson, R. B.; Junker, W. R.; Ruddy, F. H.; Beatty, J. M.; Arlia, N. G.

    2003-03-01

    This expository paper introduces the concept of on-line sensor methodologies for monitoring the integrity of components in next generation power systems, and explains general benefits of the approach, while describing early conceptual developments of suitable NDE methodologies. The paper first explains the philosophy behind this approach (i.e. the design-for-inspectability concept). Specifically, we describe where and how decades of accumulated knowledge and experience in nuclear power system maintenance are utilized in Generation IV power system designs, as the designs are being actively developed, in order to advance their safety and economy. Second, we explain that Generation IV reactor design features call for the replacement of the current outage-based maintenance by on-line inspection and monitoring. Third, the model-based approach toward design and performance optimization of on-line sensor systems, using electromagnetic, ultrasonic, and radiation detectors, will be explained. Fourth, general types of NDE inspections that are considered amenable to on-line health monitoring will be listed. Fifth, we will describe specific modeling developments to be used for radiography, EMAT UT, and EC detector design studies.

  9. On-Line Synthesis and Analysis by Mass Spectrometry

    Science.gov (United States)

    Bain, Ryan M.; Pulliam, Christopher J.; Raab, Shannon A.; Cooks, R. Graham

    2015-01-01

    In this laboratory experiment, students learn how to use ESI to accelerate chemical synthesis and to couple it with on-line mass spectrometry for structural analysis. The Hantzsch synthesis of symmetric 1,4-dihydropyridines is a classic example of a one-pot reaction in which multiple intermediates can serve to indicate the progress of the reaction…

  10. Why do People Stop Playing On-Line Games?

    DEFF Research Database (Denmark)

    Sudzina, Frantisek; Razmerita, Liana

    2012-01-01

    The recent initial public offering of shares of Zynga, probably the most important on-line game provider, drew interest of potential investors but also of general public to their business model. What the most interested people learned so far is that if Zynga had not changed their accounting...

  11. On-line survivable routing in WDM networks

    NARCIS (Netherlands)

    Beshir, A.A.; Kuipers, F.A.; Van Mieghem, P.F.A.; Orda, A.

    2009-01-01

    In WDM networks, survivable routing and wavelength assignment (SRWA) involves assigning link-disjoint primary and backup lightpaths. In the on-line SRWA problem, a sequence of requests arrive and each request is either accepted or rejected based only on the input sequence seen so far. For special

  12. On-line Survivable Routing in WDM Networks

    NARCIS (Netherlands)

    Beshir, A.A.; Kuipers, F.A.; Van Mieghem, P.; Orda, A.

    In WDM networks, survivable routing and wavelength assignment (SRWA) involves assigning link-disjoint primary and backup lightpaths. In the on-line SRWA problem, a sequence of requests arrive and each request is either accepted or rejected based only on the input sequence seen so far. For special

  13. Evaluation of Gaseous and Volatile Rare Isotopes from UCx Actinide Target 1mA of RAON ISOL System

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jae Cheon; Choi, Yeon Gyeong [Institute for Basic Science, Daejeon (Korea, Republic of); Lee, Jin Ho [Dongguk University, Gyeongju (Korea, Republic of)

    2016-10-15

    RAON, which is a heavy-ion accelerator complex that will be built in 2021, plans to produce the rare isotope (RI) beams of high purity and high intensity using the ISOL (Isotope Separation On-Line) RI production methods. For the ISOL facility, a 70 MeV proton cyclotron is used as the driver. In order to break through the technological barriers of high-power (70 kW) ISOL target, a low-power (10 kW) target will be established first. The beam intensity will be gradually ramped up to 1mA. When UCx actinide target is used for the RI beam production through the fission reaction, many unwanted gaseous and volatile radioactive isotopes will be produced simultaneously. The gaseous and volatile radioactive nuclides generated from ISOL system are very important in terms of both radiation safety for personnel and radiological impact into environment. The amount and types of major nuclides will be varied according to the proton beam energies and beam current incident on UCx actinide target. RAON plans to equip the entire set of managing and monitoring these nuclides. Especially, α-emitting and relatively long-lived nuclides from ISOL facility will be carefully monitored.

  14. IOOS Data Portals and Uniform On-line Browse Capabilities

    Science.gov (United States)

    Howard, M.; Currier, R. D.; Kobara, S.; Gayanilo, F.

    2015-12-01

    The Gulf of Mexico Coastal Ocean Observing System Regional Association (GCOOS-RA) is one of eleven Regional Associations organized under the NOAA-led U.S. Integrated Ocean Observing System (IOOS) Program Office. Each of the RAs operate standards-based regional data portals designed to aggregate near real-time and historical observed data and modeled outputs from distributed providers and to offer these and derived products in standardized ways to a diverse set of users. The RA's portals are based on the IOOS Data and Communications Plan which describes the functional elements needed for an interoperable system. One of these elements is called "Uniform On-line Browse" which is an informational service designed primarily to visualize the inventory of a portal. An on-line browse service supports the end user's need to discover what parameters are available, to learn the spatial and temporal extend of the holdings, and to examine the character of the data (e.g, variability, gappiness, etc). These pieces of information help the end user decide if the data are fit for his/her purpose and to construct valid data requests. Note that on-line browse is a distinctly different activity than data analysis because it seeks to yield knowledge about the inventory and not about what the data mean. "Uniform" on-line browse is a service that takes advantage of the standardization of the data portal's data access points. Most portals represent station locations on a map. This is a view of the data inventory but these plots are rarely generated by pulling data through the standards-based services offered to the end users but through methods only available to the portal programmers. This work will present results of Uniform On-line browse tools developed within GCOOS-RA and their applicability to other RA portals.

  15. Mentoring Narratives ON-LINE:Teaching the Principalship

    Directory of Open Access Journals (Sweden)

    Allison I. Griffith

    2002-05-01

    Full Text Available The need to develop new models for preparation of school administrators has been a prominent concern in educational discourse in the last decade. Having been criticized for the inadequate preparation of the school leadership cadre, academic departments responsible for training future school administrators have had to revisit their approaches and to reframe their teaching philosophies to ensure the readiness of their graduates for the challenges and complexities of school leadership. This article reports on the new model of principals' training that has been used in York University's Principals' Qualification Program (PQP from the late 1990s onward. One component of the program brings traditional case methodology into a computer-mediated/on-line environment. The on-line cases are narratives from the everyday lives of the Ontario school administrators who serve as mentors in the on-line environment. Situating our discussion within the context of the rapidly changing educational landscape of Ontario, we focus on the PQP model to explore experientially generated case narratives as one method for teaching and learning the work of the local school administrator. We focus particularly on the teaching and learning embedded in computer-mediated or on-line case narratives used in training teachers for school leadership. We argue that the complexities of school leadership—the social, cultural, relational, ethical and moral context of school leadership—can be taught effectively through the reflective processes of on-line case narratives. We seek to contribute to the ongoing dialogue on the potential of new pedagogies and new technologies to help prepare the competent and responsible leaders for tomorrow's schools.

  16. GPS Separator

    CERN Multimedia

    2016-01-01

    Footage of the 70 degree ISOLDE GPS separator magnet MAG70 as well as the switchyard for the Central Mass and GLM (GPS Low Mass) and GHM (GPS High Mass) beamlines in the GPS separator zone. In the GPS20 vacuum sector equipment such as the long GPS scanner 482 / 483 unit, faraday cup FC 490, vacuum valves and wiregrid piston WG210 and WG475 and radiation monitors can also be seen. Also the RILIS laser guidance and trajectory can be seen, the GPS main beamgate switch box and the actual GLM, GHM and Central Beamline beamgates in the beamlines as well as the first electrostatic quadrupoles for the GPS lines. Close up of the GHM deflector plates motor and connections and the inspection glass at the GHM side of the switchyard.

  17. HRS Separator

    CERN Multimedia

    2016-01-01

    Footage of the 90 and 60 degree ISOLDE HRS separator magnets in the HRS separator zone. In the two vacuum sectors HRS20 and HRS30 equipment such as the HRS slits SL240, the HRS faraday cup FC300 and wiregrid WG210 can be spotted. Vacuum valves, turbo pumps, beamlines, quadrupoles, water and compressed air connections, DC and signal cabling can be seen throughout the video. The HRS main and user beamgate in the beamline between MAG90 and MAG60 and its switchboxes as well as all vacuum bellows and flanges are shown. Instrumentation such as the HRS scanner unit 482 / 483, the HRS WG470 wiregrid and slits piston can be seen. The different quadrupoles and supports are shown as well as the RILIS guidance tubes and installation at the magnets and the different radiation monitors.

  18. On-line digestion system for protein characterization and proteome analysis.

    Science.gov (United States)

    López-Ferrer, Daniel; Petritis, Konstantinos; Lourette, Natacha M; Clowers, Brian; Hixson, Kim K; Heibeck, Tyler; Prior, David C; Pasa-Tolić, Ljiljana; Camp, David G; Belov, Mikhail E; Smith, Richard D

    2008-12-01

    An efficient on-line digestion system that reduces the number of sample manipulation steps has been demonstrated for high-throughput proteomics. By incorporating a pressurized sample loop into a liquid chromatography-based separation system, both sample and enzyme (e.g., trypsin) can be simultaneously introduced to produce a complete, yet rapid digestion. Both standard proteins and a complex Shewanella oneidensis global protein extract were digested and analyzed using the automated online pressurized digestion system coupled to an ion mobility time-of-flight mass spectrometer, an ion trap mass spectrometer, or both. The system denatured, digested, and separated product peptides in a manner of minutes, making it amenable to on-line high-throughput applications. In addition to simplifying and expediting sample processing, the system was easy to implement and no cross-contamination was observed among samples. As a result, the online digestion system offers a powerful approach for high-throughput screening of proteins that could prove valuable in biochemical research (rapid screening of protein-based drugs).

  19. Astronomy On-Line Programme Enters "hot Week"

    Science.gov (United States)

    1996-11-01

    World's Biggest Astronomy WWW-Event Attracts Thousands of Students The Astronomy On-line Programme (See ESO Press Release 09/96 of 18 June 1996) began officially on 1 October and is now about to enter its most intense phase, known as the Hot Week . On 18 - 22 November, an estimated 4000 astronomy-interested, mostly young people in Europe and on four other continents will get together during five days in what - not unexpected - has become the world's biggest astronomy event ever organised on the World Wide Web. This carefully structured Programme is carried out in collaboration between the European Association for Astronomy Education (EAAE), the European Southern Observatory and the European Commission, under the auspices of the Fourth European Week for Scientific and Technological Culture. The Programme has already had a most visible impact on the school education of natural sciences in various countries; for instance, the Internet-connection of schools has been advanced in some, in order to allow groups to participate. There have been numerous contacts among the groups across the borders and there are clear signs that many Astronomy On-line participants have progressed to use the impressive possibilities of the Web in an efficient and structured way. There has been a lively media interest in Astronomy On-line all over Europe and it is expected to increase during the next week. The current status of Astronomy On-line It is obvious that the pilot function of the Astronomy On-line Programme in the use of the Web has been very effective and that the associated dissemination of astronomical knowledge has been successful. At this time, more than 650 groups have registered with Astronomy On-line. Most come from 31 different European countries and a few dozen groups are located in North and South America as well as in Asia and Australia. Together they have experienced the steady build-up of Astronomy On-line over the past weeks, by means of numerous contributions from a

  20. Rare Earth Separation in China

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    During the last decade, China rare earth (RE) industry has made significant progress and become one of the most important producers in the world. In this paper, the recent developments in both fundamental research and industrial application are briefly reviewed: (1) the development and application of Theory of Countercurrent Extraction, (2) the novel solvent extraction process and its application in industry for separating heavy rare earth elements (Tm, Yb, Lu), yttrium (Y), and scandium (Sc), (3) the on-line analysis and automatic control of countercurrent extraction, (4) the eco-friendly process for RE/Th separation of bastnasite in Sichuan Province and electrochemical process for Eu/RE separation, and (5) the optimized flowcharts for typical rare earth minerals in China.