WorldWideScience

Sample records for okeru sekitan riyo

  1. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Survey by region/industry in India; Kankyo chowagata sekitan riyo system kanosei chosa. Indo ni okeru sekitan riyo gaikyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A survey was made in India which is a coal producing/consuming country following China in Asia and where coal is used for about 60% of the primary commercial energy. The survey was conducted on coal production/distribution/utilization and environmental issues, aiming at studying feasibility of introducing the environmentally friendly coal utilization system into every industry including the residential/commercial one, and at implementing a comprehensive master plan including Japan`s international cooperation. Total power source facilities in fiscal 1995 are 83.3 million kW, 64% of which are coal thermal power facilities and generated 260 TWh, 69% of the total output energy. Main commercial energy sources are coal, oil and natural gas, and oil is self-sufficient. The survey this time did not examine very well the actual state of the environmental pollution problem caused by the coal utilization. Indian coal is high in ash content but low in sulfur content, and therefore, SOx polluting air has not been a very important problem so far, but soot/smoke is almost the problem. Further, ash treatment after combustion at boilers, etc. is expected to be a big problem in the future. 49 figs., 88 tabs.

  2. Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in the Philippines; Kankyo chowagata sekitan riyo system kanosei chosa. Philippines ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With relation to the coal of the Philippines, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/development, the trend of coal import and domestic distribution, the coal utilization trend, and environmental problems, and analyzed the situation of coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to draw up a master plan for the introduction of the environmentally-friendly coal utilization system. As to the use of environmentally-friendly coal technology which should be adopted to the coal mining industry and commercial/residential sector, cited are the introduction of coal preparation technology and power transmission technology, and the development/spread of briquette as a firewood substituting fuel. In the electric power sector, the problem is the treatment of ash after combustion and the effective use. Relating to the treatment of flue gas, there is no installation at all of desulfurization facilities and denitrification facilities. In the cement industry sector, they wish to return fuel from heavy oil to coal. For it, it is necessary to study dust preventive measures. In the other sectors, coal hasn`t been used very much. An increase in coal demand is not expected also in the future, and big problems concerning coal haven`t occurred. 42 figs., 64 tabs.

  3. Fiscal 1997 survey report. Feasibility study of the environmentally friendly type coal utilization system (survey of the coal utilization in Pakistan); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Pakistan ni okeru sekitan riyo gaikyo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper made a literature survey, hearing survey, site survey/study on the coal in Pakistan such as the coal utilization system and the environmental situation, etc., and aimed at pre-examination for the survey of the introduction of the environmentally friendly type coal utilization system to be planned in Pakistan in the future. The examination, data collection and preparation were conducted in terms of the following items: the structure of coal consumption in energy supply, structure of coal consumption, mainly of domestic brown coal consumption, the situation of coal utilization by industry and by region, environmental problems caused by coal utilization such as air pollution, the trend of policies of environmental regulation, etc. The literature on the following was obtained and surveyed: the situation of economy/energy in Pakistan, coal utilization technology by industrial field, and environmental protection technology. The hearing survey was made to institutions concerned, corporation groups and men of learning and experience. Site surveys were conducted for the typically selected coal utilization equipment and existing environmental protection equipment. 66 figs., 56 tabs.

  4. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper investigated and studied the present situation and future trend of coal utilization and distribution in Thailand, and the present situation of environmental effects and the measures taken for environmental protection. Around 2010, coal will probably be produced only at EGAT`s Mae Moh (MM) coal mine. Demand for overseas coal is expected to be 40-50 million tons in 2011, and preparation of the coal center becomes a subject. For general industry use coal, pretreatment such as coal preparation, coal blending and briquetting is needed, considering coal quality, usage, transport distance and environmental effects. Brown coal of MM coal mine is a lignite with high sulfur, high ash content and low heating value. Wide spread of its use can be expected if upgrading is possible such as desulfurization, deashing, increasing heating value. In the electric power generation field, the absorber was installed at the existing boiler of the mine-mouth generating plant to conduct a verification test on high grade desulfurization of ultra-high sulfur lignite. In the industry field, the circulating fluidized bed boiler was adopted. In the residential/commercial field, introduction of briquette was proposed. 80 refs., 84 tabs.

  5. Fiscal 1995 survey report on the feasibility study of the environmentally friendly type coal utilization system. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    The paper surveyed the present situation and future trend of economy, energy supply/demand, coal production/distribution/utilization and the environmental effects in Thailand. The survey on the coal utilization and its environmental effects was partially requested of the environmental research institute in Thailand. The amount of coal utilization in Thailand rapidly increased to nearly four times as large as that ten years ago mainly in terms of domestic lignite under the government`s policy on expansion of the domestic energy use. However, most of this domestic lignite is low-grade coal with low calories and high sulfur content, and the use of it was rapidly increased mostly in power generation sector without no adequate environmental measures taken. This caused an environmental problem on air pollution due to sulfur oxides at Mae Moh power plant in the north several years ago, and the damages to the regional residents, etc. were given much publicity by journalism and developed the social problem. Accordingly, Thai people are now critical of the coal resource exploration and the coal use expansion. Under the circumstances, the Ministry of Industry and the energy related ministries/offices are obliged to review their development/promotion plans. 84 figs., 99 tabs.

  6. Fiscal 1995 survey report on the feasibility study of the environmentally friendly type coal utilization system. Survey on the environmentally friendly type coal utilization system in the coal preparation sector in China; Kankyo chowagata sekitan riyo system kanosei chosa. Chugoku no sentan bumon ni okeru kankyo chowagata sekitan riyo system ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    Specifying the coal preparation technology among clean coal technologies (CCT) in China, the paper investigated governmental policies, plans, standards of coal preparation technology, subjects, etc. toward the introduction/spread of coal preparation technology, and studied decision, introduction and spread of the coal preparation system suitable for the coal utilization status in China. The survey was conducted in Shanxi and Henan Provinces which are main provinces of coal production, and field survey was made at some selected coal preparation plants having different operational conditions. In the field survey, problems on the operation were extracted, and points of improvement were studied at the same time. Further, to grasp the positioning of coal preparation in CCT in China, survey was carried out on laws and regulation on coal preparation in terms of energy and environmental policies. Finally, the result of the field survey was analyzed, a coal preparation system of which the introduction/spread in medium- and long-term are enabled was proposed considering the coal utilization status and economic situation in China, and how to introduce/spread it was studied. 35 figs., 42 tabs.

  7. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper investigated and studied the present situation and future trend of coal utilization and distribution in Thailand, and the present situation of environmental effects and the measures taken for environmental protection. Around 2010, coal will probably be produced only at EGAT`s Mae Moh (MM) coal mine. Demand for overseas coal is expected to be 40-50 million tons in 2011, and preparation of the coal center becomes a subject. For general industry use coal, pretreatment such as coal preparation, coal blending and briquetting is needed, considering coal quality, usage, transport distance and environmental effects. Brown coal of MM coal mine is a lignite with high sulfur, high ash content and low heating value. Wide spread of its use can be expected if upgrading is possible such as desulfurization, deashing, increasing heating value. In the electric power generation field, the absorber was installed at the existing boiler of the mine-mouth generating plant to conduct a verification test on high grade desulfurization of ultra-high sulfur lignite. In the industry field, the circulating fluidized bed boiler was adopted. In the residential/commercial field, introduction of briquette was proposed. 80 refs., 84 tabs.

  8. Fiscal 1997 feasibility survey of an environment friendly type coal utilization system. Feasibility survey of the environment friendly type coal utilization system in Malaysia and Vietnam (case of Vietnam); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Malaysia oyobi Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa (Vietnam ban))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper grasped the state of coal utilization by coal consumption field, the state of coal physical flow in Vietnam, etc., surveyed/studied a possibility of introducing the environment friendly type coal utilization system, and assessed the possibility. As to energy resources, the north is abundant in hydroelectric and coal (mainly anthracite) resources, and the south in oil and natural gas resources. Coal production in fiscal 1997 is planned to be 10 million tons. Coal preparation technique presently available is only grain size sieving. Accordingly, it is necessary to study for heightening efficiency of facilities and modernizing facilities in accordance with the introduction of the environment friendly type coal utilization technology. During the study, it is possible to propose improvement on coal processing technology (coal preparation technology). Assessment and study are made especially of the coal selection system, fine coal recovery system and waste water treatment system. For the plan on new coal-fired power plants (300MWtimes4), there is left much necessity of proposing studying models considered of the anthracite combustion technology and environmental improvement and of assessing/studying them. 60 figs., 117 tabs.

  9. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in the Philippines; Kankyo chowagata sekitan riyo system kanosei chosa. Philippines ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Grasping the present situation of coal utilization technology in the Philippines, the paper proposed a feasibility study of introduction of the environmentally friendly type coal utilization system which seems to be needed in the future. (1) Introduction of the environmentally friendly type coal utilization system in the electric power generation sector: there are only four full-scale running coal thermal power plants in the Philippines. In the future, several coal thermal plants are planned to be constructed by 2005, but for the new installation, it is desirable to adopt fluidized bed boilers with wide application to coal kinds. In case of 0.3-1.0 million MW class plants, it is planned to adopt high grade import coals, and it will be natural to fire pulverized coal. For the processing of flue gas, it is a must to install desulfurization facilities and smoke/soot removal devices. (2) Utilization/development of domestic low grade coals: at the mine-mouth generating plant, it is necessary to investigate the economically minable amount of coal, confirm productivity, survey coal quality, etc., and select boiler. As to coal briquetting technology, it is necessary to examine coal quality for tests and make a thorough study of what technology is most suitable. 50 figs., 78 tabs.

  10. Fiscal 1997 survey report. Feasibility study of the environmentally friendly type coal utilization system (feasibility study of the environmentally friendly type coal utilization system in India); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Indo ni okeru kankyo chowagata sekitan riyo system kanosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The survey was conducted of the present situation of coal utilization and the present coal situation such as the environmental state of India which is a coal producing/consuming country next to China in Asia. The paper studied a feasibility of the introduction of the environmental friendly type coal utilization system` to be planned in India. The items for survey are the present situation of economy and energy and the future trend, environmental problems on coal utilization, the present status of the coal distribution system and study subjects, the present status of coal utilization by field and study subjects, a possibility of briquette use, a possibility of coal fluidization, electric power development plans and coal combustion technology in each industry, etc. The subjects are the obligation of coal preparation to coal thermal power plants 1000 km away from coal mines starting 2001, measures taken for effective ash use, measures taken for superannuated gas furnaces, etc. Based on the results of these site surveys and reports of the investigation under consignment from CMPDI, the paper studied/analyzed possibilities of introducing the coal utilization system having actual introduction results in Japan to India, and made an investigational report. 39 refs., 12 figs., 56 tabs.

  11. Research report of FY 1997 on the environmentally acceptable coal utilization system feasibility survey. Environmentally acceptable coal utilization system feasibility survey in Malaysia and Vietnam (Malaysia); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Malaysia oyobi Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa (Malaysia ban))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In this survey, the coal utilization status in individual consumption sectors and coal distribution status in Malaysia are summarized as basic data for the introduction of environmentally acceptable coal utilization systems. In this fiscal year, the status of existing coal utilization technology and environmental issues in Malaysia are summarized as basic data for the introduction of above-mentioned systems on the basis of data and information collected by basic research and site survey in FY 1996. Malaysia is one of the rich countries producing the primary resources with crude petroleum, natural gas, hydro-power, and coal. The coal demand will be realized after saturating LNG development since 2000. The major coal consumption industries are power generation sector and cement industry sector. As expected increase in the future coal consumption, efficiency of coal utilization and environmental issues are problems in the future. Based on the FS results of this survey, the survey will be continued for planning and conducting the model project required from Malaysia. 8 figs., 34 tabs.

  12. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Malaysia and Vietnam; Kankyo chowagata sekitan riyo system kanosei chosa. Malaysia Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This survey arranged the status of coal utilization technology and the status of coal production, supply, etc. in Malaysia and Vietnam, examined/studied coal utilization systems in both countries, and finally assessed feasibility of introducing the environmentally friendly type coal utilization system. As a country of primary energy source which is abundant in crude oil, natural gas, hydroelectric power, coal, etc., Malaysia now depends on crude oil and natural gas for 80% of its energy, and places emphasis on exploration of natural gas and oil refining. In electric power and cement industries where coal is consumed, effectiveness and environmental issues in association with coal utilization are future subjects. In Vietnam, the north is abundant in hydroelectric power and anthracite, and the south in oil and gas resource, but the north and central districts are in a state of undevelopment. Coal is used for coal thermal power generation, cement industry, and residential/commercial fuel. In the future, effective coal utilization and environmental issues will be subjects. 16 refs., 38 figs., 75 tabs.

  13. Research report of FY 1997 on the environmentally acceptable coal utilization system feasibility survey. Clean coal technology model project seminar held in Thailand; 1997 nendo seika hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Tai ni okeru clean coal technology model jigyo seminar no kaisai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-02-01

    To reduce SOx with coal utilization, the desulfurization seminar diffusing the demonstration project of simplified desulfurizer introduction was held at the site in Thailand. The purpose is to reduce the environmental pollutants and contribute to the effective utilization of energy with coal utilization in Thailand. Invitation letters were sent to users of coal and heavy oil boilers through the Department of Factories, Ministry of Industry, Thailand, to call participation in the seminar. Inspection of the desulfurizer introduced in the factory of Thai Union Paper Public was included in the seminar for diffusing the project. The inspection site is in the demonstration project site of simplified desulfurizer introduction. There were a lot of participants from Thai users and from Japan. The seminar included the presentations from NEDO, JETRO, FTI, and MOSTE, introduction of general technology for processes of ENAA desulfurizer, introduction of demonstration unit plan by IHI, and introduction of operation of demonstration unit by TUP. 31 figs., 6 tabs.

  14. 6th Conference on Coal Utilization Technology; Dai 6 kai sekitan riyo gijutsu kaigi koenshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-01

    The paper compiled the papers presented in the 6th Conference on Coal Utilization Technology held in September 1996. With relation to the fluidized bed boiler, reported were Field operation test of Wakamatsu PFBC combined cycle power plant and Development of pressurized internally circulating fluidized bed combustion technology. Regarding the coal reformation, Development of advanced coal cleaning process, Coal preparation and coal cleaning in the dry process, etc. Concerning the combustion technology, Study of the O2/CO2 combustion technology, Development of pressurized coal partial combustor, etc. About the CWM, Development of low rank coals upgrading and their CWM producing technology, Technique of CWM distribution system, etc. Relating to the coal ash, Engineering characteristics of the improved soil by deep mixing method using coal ash, Employment of fluidized bed ash as a basecourse material, On-site verification trials using fly ash for reclamation behind bulkheads, Water permeabilities of pulverized fuel ash, Separation of unburned carbon from coal fly ash through froth flotation, Practical use technology of coal ash (POZ-O-TEC), etc

  15. Volatiles production from the coking of coal; Sekitan no netsubunkai ni okeru kihatsubun seisei

    Energy Technology Data Exchange (ETDEWEB)

    Yamashita, Y.; Saito, H.; Inaba, A. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    In order to simplify the coke manufacturing process, a coke production mechanism in coal pyrolysis was discussed. Australian bituminous coal which can produce good coke was used for the discussion. At a temperature raising rate of 50{degree}C per minute, coal weight loss increases monotonously. However, in the case of 3{degree}C, the weight loss reaches a peak at a maximum ultimate temperature of about 550{degree}C. The reaction mechanism varies with the temperature raising rates, and in the case of 50{degree}C per minute, volatiles other than CO2 and propane increased. Weight loss of coal at 3{degree}C per minute was caused mainly by methane production at 550{degree}C or lower. When the temperature is raised to 600{degree}C, tar and CO2 increased, and so did the weight loss. Anisotropy was discerned in almost of all coke particles at 450{degree}C, and the anisotropy became remarkable with increase in the maximum ultimate temperature. Coke and volatiles were produced continuously at a temperature raising rate of 50{degree}C per minute, and at 3{degree}C per minute, the production of the coke and volatiles progressed stepwise as the temperature has risen. 7 refs., 6 figs.

  16. Use of natural energy in hyper-skyscrapers. Chocho koso kenchiku ni okeru shizen energy riyo

    Energy Technology Data Exchange (ETDEWEB)

    Unno, K. (Takenaka Komuten Co. Ltd., Osaka (Japan))

    1992-05-30

    Construction of large scale hyper-skyscrapers( more than 500 m high ) by next century is coming to inevitable stage, and the problems regarding supply and consumption of energy/resources together with the use of natural energy in such construction are described. Transport of water at high direction, conformity of supply and save energy are pointed out as problems for supplying water energy. Calculated amount of required electrical energy used by electrical appliances of sky-city ( 1000 m high ) has been about 440,000 KVA, and necessity of autonomous supply network system for electric power and heat supply is stressed. For sky-city, 1000 m, use of new energy( supply of 20% of total electric power is possible with optical generation, wind power generation) and the use of unused energy ( draft generations, generation from refuse incineration, pumped storage generation ) are emphasized. Effective supply of water resource like refuse of waste water is cited. 3 refs., 4 figs., 1 tab.

  17. Solar energy drying for agricultural products. Nosanbutsu kanso ni okeru taiyonetsu riyo

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Jun' ichi (National Grassland Research Inst., Tochigi, (Japan))

    1989-09-30

    Natural drying was previously used to dry agricultral products but artificial drying is widely used today with the diffusion of agricultural machines. Therefore, solar energy utilization to dry agricultural products depends on how effective solar energy is utilized in addition to the mechanized artificial drying. Further, drying of agricaltural products varies in respective countries and local areas because water content in products varies on weather conditions. Wheats harvested in U.S. contain fewer water content and can be dried for 3 months in a large storing bin by natural ventilation and cn be shortened to 1 month by placing a solar collector before the blower. Many Japanese farmers utilize vinyl houses and drying is made by combining vinyl house, and flat floor type dryer, circulating dryer or rotary stirring dryer. Moreover, 100% utilization of solar enegy results higher cost, so that in many cases, combined utilization with oil firing is made. Moderate heat such as solar energy is suitable for drying of agricultural products to maintain the quality and it is desirable to develop any reasonal technique. 14 refs., 12 fig.

  18. Studies on reactivity of coal surfaces at low temperature; Teion ni okeru sekitan hyomen no hannosei no kento

    Energy Technology Data Exchange (ETDEWEB)

    Yasuda, H.; Kaiho, M.; Yamada, O.; Soneda, Y.; Kobayashi, M.; Makino, M. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    With an objective to learn reactivity of coal at its surface, surfaces of oxidized coal samples were investigated. Miike coal was oxidized by using {sup 18}O2 in a closed loop system. As the reaction progresses, proportion of CO2 including isotopes increased rapidly as a result of oxidation of CO sites existing in the coal and the newly generated C{sup 18}O sites. The oxidizing reaction progressed via oxygen adsorbing sites generated near the surface, and oxygen containing groups. An FT-IR analysis estimated the depth of the oxidized layer to be 10{mu}m or less from particle surface. The oxidized coal was pulverized to see its surface condition. Functional groups introduced by the oxidation enter into the vicinity of the surface in a form to desorb as CO. CO2 is trapped in inner pores. The coal surface was observed by using an atomic force microscope. No observable openings in the pore structure were discerned on the surface before the oxidation, and the structure agrees with a closed pore model. Surface image oxidized in-situ by oxygen for one hour had slight roundness, which led to a supposition of structural change, and changes in the functional group and adsorption species. 7 refs., 5 figs.

  19. Numerical simulation of coal combustion in circulating fluidized beds; Junkan ryudoso ni okeru sekitan nensho no suchi simulation

    Energy Technology Data Exchange (ETDEWEB)

    Schoenfelder, H. [Technical University Hamburg, Hamburg (Germany); Suzuki, Y.; Hatano, H. [National Institute for Resources and Environment, Tsukuba (Japan)

    1997-09-25

    A numerical simulator has been developed, using a one-dimensional heterogeneous reaction model, for circulating fluidized bed combustors. The model is based on the Johnson`s method for modeling circulating fluidized bed combustors operating at low gas velocity, and involves kinetic models of combustion process and fluidization mechanisms in circulating fluidized bed risers. In order to determine rate parameters for coal combustion, Chinese coal is combusted by a circulating fluidized bed combustor of quartz, installed at the National Institute for Resources and Environment. The simulation after parameter-fitting indicates that char produced from coal shows a medium activity for NO reduction and very low activity for N2O reduction. It is also found that reduction of No by CO is very important. The simulator satisfactorily gives gas concentration at the combustor outlet and axial distributions of the vapor component concentrations. 19 refs., 11 figs., 5 tabs.

  20. Application of membrane technology to food industry; Shokuhin kogyo bun'ya ni okeru maku riyo

    Energy Technology Data Exchange (ETDEWEB)

    Kamata, T.; Nakajima, M. [Univ. of Tsukuba, Tsukuba (Japan)

    2000-08-05

    In the food industry, the membrane technologies are used practically for concentration of fruit juice and milk, etc. as reverse osmosis, for decolorization and desalination of liquid seasoning as nanofiltration, for bacteria elimination, etc. as micro-filtration, for recovery and purification of the protein as ultra-filtration, and for kitchen salt manufacturing and desalination as electrodialysis. In this paper, the state of utilization of membranes and the trend of recent research and development in the food industry are described. At first, a utilization of membranes in the dairy industry field, the fruit juice processing field, the alcoholic beverage field, the seasoning field, the honey purification field, the protein field and the fats and oils processing field are described. Next, as a film emulsification technology, a preparing process of W/O emulsion in which the pressurized water phase is penetrated through a hydrophobic membrane into the oil phase of the opposite side, and a preparing process of W/O emulsion in which the pressurized oil phase is penetrated through a hydrophilic film are described. The emulsification technology using the micro-channel made of the silicon chip, which is developed by the author is introduced. (NEDO)

  1. Transition of wind power utilization technology in the 20th century; 20 seiki ni okeru furyoku riyo gijutsu no hensen

    Energy Technology Data Exchange (ETDEWEB)

    Ushiyama, I. [Ashikaga Inst. of Tech., Tochigi (Japan)

    2000-04-01

    Windmills are one of the oldest prime movers and have been used for more than 700 years in Europe. The transition from low speed windmills for grain grinding and water pumping to high speed wind turbines for electric power generation had occurred at the end of 19{sup th} century. This paper, at first, reviews the windmill technologies and the researchers before 20th century. Then describes the back ground of how the wind power generator has existed and how the four pioneers developed their wind power generator. The historical developments of windmills to wind turbines in this century are studied focusing mainly on Danish activities. Then, the effort of the development of large wind turbine such as Smith-Putnum's first MW machine in U.S.A. and other mammoth machine concept are introduced. The new concept machines such as Savonius and Darrieus wind turbines in 1920s to 1930s are also explained. Finally, the novel technologies of wind turbine covering larger machines, variable speed generators, special wing sections for wind turbines, theoretical analysis method of wind turbine performance, offshore wind turbines, and wind turbine control technologies are stated. (author)

  2. Environmentally friendly type coal utilization technology transfer project. Downstream field; Kankyo chowagata sekitan riyo gijutsu iten jigyo. Karyu bun`ya

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper arranged the result of the clean coal technology transfer project carried out during October to December, 1996. For the purpose of supporting introduction/spread of clean coal technology (CCT) in Asian and Pacific countries, the project invited engineers of the countries to Japan, aiming at fermentation of the understanding of CCT and improvement in ability. The project was held by NEDO and managed by Center for Coal Utilization, Japan. The manager course is for policy decision makers, management and senior management (plant manager class). By taking up CCT assessment and a menu of economical efficiency, prepared was the environment to which CCT is introduced in case of working out policy and planning plant/equipment investment. Moreover, the engineer course is for policy planners, medium-class management (section chief class), senior engineers (planners), and takes up materials for judgment in case of planning CCT facilities and proposing measures to reduce environmental loads by management and improvement of facilities at the same time. Fifteen engineers were invited: 6 from China, 3 from Indonesia, 3 from the Philippines, and 3 from Thailand

  3. Utilization of coal ash from fluidized-bed combustion boilers as road base material. Ryudosho boiler sekitan nenshobai no robanzai eno riyo

    Energy Technology Data Exchange (ETDEWEB)

    Ito, H.; Shibata, Y.; Takada, T.; Yamamuro, H. (Kawasaki Heavy Industries, Ltd., Tokyo (Japan))

    1994-07-20

    The present report reports the technological development to utilize coal ash from the fluidized-bed combustion boiler as a road base material. In case of mass production by low pressure press forming, the following hardening conditions are reported to be appropriate for kneading the ash only with water, curing it with steam and obtaining the higher compressive strength of thus hardened ash than 150kgf/cm[sup 2]: the boiler operational condition is to be adjusted so that the CaO content and char content may exceed 10% and fall bellow 20%, respectively of the coal ash. The kneading water rate is to be set around the plastic limit of coal ash. The duration of precuring and main precuring is to be 6 to 10h, at 30[degree]C and 10 to 15h at 60[degree]C, respectively. Explained is the result of mass production test with kneader, plastic former and crusher of the same structure as the presumed actual ones, and assessment test (laboratory test and field test on the road pavement) on the hardened and crushed ash with the compressive strength of 170kgf/cm[sup 2] as a pavement material. The present report also reports the operational start of a demonstration plant for the base material production. 5 refs., 11 figs., 2 tabs.

  4. Development of melting system using oxy-coal combustion; Sekitan chokusetsu riyo kinzoku yoyu system gijutsu (NSR) (pilot setsubi unten jokyo ni tsuite)

    Energy Technology Data Exchange (ETDEWEB)

    Sugiyama, T. [Center for Coal Utilization, Japan, Tokyo (Japan); Suwa, T.; Kobayashi, N.; Iino, K.; Yamamoto, Y.; Igarashi, H. [Nippon Sanso K.K., Tokyo (Japan)

    1996-09-01

    This metal melting system is a process to efficiently melt and regenerate scraps of aluminum, copper and iron by utilizing high-temperature energy obtained from pulverized coal-oxygen combustion. The process is intended to utilize coal in place of petroleum for reduced fuel cost. Joint studies have been carried out as a subsidy operation of the Agency of Natural Resources and Energy with a schedule of six years starting fiscal 1992. Development tests are being performed using a 5-ton/ch pilot plant facility since fiscal 1995 after having gone through experiments using a 1-ton/ch bench scale furnace. This paper reports the results obtained to date. Using the pilot plant facility, fiscal 1995 has achieved the initial target values, such as thermal efficiency of 55% or higher, and yield of 96% or higher for non-ferrous metals and 94% or higher for iron. The melting behavior in the furnace has improved the thermal efficiency as a whole by retaining the conditions in the preheating step for an extended period of time. The thermal efficiency has been improved better than with the bench furnace as a result of upscaling effect. 9 figs., 3 tabs.

  5. Basic research program for innovated coal utilization in Japan. BRAIN-C program; Sekitan riyo kiban gijutsu kaihatsu. BRAIN-C program

    Energy Technology Data Exchange (ETDEWEB)

    Harada, M. [Center for Coal Utilization, Japan, Tokyo (Japan)

    1996-09-01

    This paper introduces the circumstances and purpose of establishing the Basic Research Associate for Innovated Coal Utilization (BRAIN-C) Program started in October 1995, and the summary of the results therefrom in fiscal 1995. Although development of coal utilization technologies has been implemented over a number of years, there are many problems still requiring solutions. Early realization has been urged on diversification of coal utilization, acceleration of technological development and diversification of coal types. In order to achieve these goals, the necessity was recognized afresh on not only the hardwares, but also on basic technologies in terms of software which can identify properties of coals, systematize different reactions, and estimate reactions, fluidity and heat transmission of coals. Therefore, receiving a subsidy from the Agency of Natural Resources and Energy of the Ministry of International Trade and Industry, a research and development program to be implemented jointly by industries, administrative agencies and academic societies had been started with a five-year plan for the time being. With the activities for the program such as collecting 50 to 100 types of coals and supplying them to researchers, the program had been accelerated in fiscal 1995 on a large number of themes and results therefrom, including fundamental properties and thermo-chemical reactions. 2 figs., 4 tabs.

  6. Fiscal 1997 for the upgrading of the Asia/Pacific coal development. Survey of the optimization of the coal transportation system in Indonesia; 1997 nendo Asia Taiheiyo sekitan kaihatsu kodoka chosa. Indonesia ni okeru sekitan yuso system saitekika chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper summarized the results of Phase 1 and Phase 2 surveys conducted based on `Agreement on the comprehensive survey of a coal transportation system in South Sumatra` concluded between NEDO and the Ministry of Mine and Energy in Indonesia. In addition to the data collection and site surveys made in Phase 1, conducted in Phase 2 were determination of sites for harbors, determination of a scenario on coal transportation from coal mines to harbors, optimization of the coal transportation system, social/economic assessment, and proposal on the optimum transportation system. The results of the simulation were as follows: It is the most advantageous to transport coal from coal deposit area to harbor by rail and from harbor to Paiton by barge weighed over 10,000 tons. Tanjung Api Api is the most advantageous as harbor. The production scale which is profitable became more than 15 million tons. The present coal price of PTBA is $25/t arriving Suralaya. The coal in this case is said to be 5500kcal/kg in quality, and the coal of the same quality to this is only profitable. 8 refs., 68 figs., 104 tabs.

  7. Fiscal 1996 survey for the upgrading of the Asia/Pacific coal development. Survey of the coal infrastructure propagation in Indonesia; 1996 nendo Asia Taiheiyo sekitan kaihatsu kodoka chosa. Indonesia ni okeru sekitan infura seibi chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    Phase 1 survey in fiscal 1996 was conducted based on `Agreement on the comprehensive survey of a coal transportation system in South Sumatra` concluded between NEDO and the Ministry of Mine and Energy in Indonesia. In the survey, conducted were collection of data on coal fields and site surveys, collection of data on inland transportation and site surveys, collection of data on harbors and site surveys, and worked out were a simplified database and a coal transportation plan by optimization of the coal chain system. The area for survey is the periphery of the Musi River of South Sumatra. The results of the simulation by LP models were as follows: When the coal of Bukit Asam coal mine is $25/t in price, only coal of 5500Kcal/kg is profitable, and when $27/t in price, coal of 4500Kcal/kg also becomes profitable. This shows that if the coal is of good quality, it can pay arriving at Suralaya, independent of the distance of transportation. 47 figs., 63 tabs.

  8. Change in surface characteristics of coal in upgrading of low-rank coals; Teihin`itan kaishitsu process ni okeru sekitan hyomen seijo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Oki, A.; Xie, X.; Nakajima, T.; Maeda, S. [Kagoshima University, Kagoshima (Japan). Faculty of Engineering

    1996-10-28

    With an objective to learn mechanisms in low-rank coal reformation processes, change of properties on coal surface was discussed. Difficulty in handling low-rank coal is attributed to large intrinsic water content. Since it contains highly volatile components, it has a danger of spontaneous ignition. The hot water drying (HWD) method was used for reformation. Coal which has been dry-pulverized to a grain size of 1 mm or smaller was mixed with water to make slurry, heated in an autoclave, cooled, filtered, and dried in vacuum. The HWD applied to Loy Yang and Yallourn coals resulted in rapid rise in pressure starting from about 250{degree}C. Water content (ANA value) absorbed into the coal has decreased largely, with the surface made hydrophobic effectively due to high temperature and pressure. Hydroxyl group and carbonyl group contents in the coal have decreased largely with rising reformation treatment temperature (according to FT-IR measurement). Specific surface area of the original coal of the Loy Yang coal was 138 m{sup 2}/g, while it has decreased largely to 73 m{sup 2}/g when the reformation temperature was raised to 350{degree}C. This is because of volatile components dissolving from the coal as tar and blocking the surface pores. 2 refs., 4 figs.

  9. Effect of sulfur or hydrogen sulfide on initial stage of coal liquefaction in tetralin; Sekitan ekika shoki katei ni okeru io to ryuka suiso no hatasu yakuwari

    Energy Technology Data Exchange (ETDEWEB)

    Nakada, M. [Government Industrial Research Institute, Kyushu, Saga (Japan)

    1996-10-28

    It is well known that the solubilization of coal can be accelerated by adding sulfur or hydrogen sulfide during direct liquefaction of difficult coals. From the studies of authors on the coal liquefaction under the conditions at rather low temperatures between 300 and 400{degree}C, liquefaction products with high quality can be obtained by suppressing the aromatization of naphthene rings, but it was a problem that the reaction rate is slow. For improving this point, results obtained by changing solvents have been reported. In this study, to accelerate the liquefaction reaction, Illinois No.6 coal was liquefied in tetralin at temperature range from 300 to 400{degree}C by adding a given amount of sulfur or hydrogen sulfide at the initial stage of liquefaction. The addition of sulfur or hydrogen sulfide provided an acceleration effect of liquefaction reaction at temperature range between 300 and 400{degree}C. The addition of sulfur or hydrogen sulfide at 400{degree}C increased the oil products. At 370 and 400{degree}C, the liquid yield by adding sulfur was slightly higher than that by adding hydrogen sulfide, unexpectedly. The effects of sulfur and hydrogen sulfide were reversed when increasing the hydrogen pressure. 5 figs., 1 tab.

  10. Coal conversion rate in 1t/d PSU liquefaction reactor; 1t/d PSU ekika hannoto ni okeru sekitan tenka sokudo no kento

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, K.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

    1996-10-28

    To investigate the coal liquefaction characteristics, coal slurry samples were taken from the outlets of the reactors and slurry preheater of NEDOL process 1 t/d process supporting unit (PSU), and were analyzed. Tanito Harum coal was used for liquefaction, and the slurry was prepared with recycle solvent. Liquefaction was performed using synthetic iron sulfide catalyst at reaction temperatures, 450 and 465{degree}C. Solubility of various solid samples was examined against n-hexane, toluene, and tetrahydrofuran (THF). When considering the decrease of IMO (THF-insoluble and ash) as a characteristic of coal conversion reaction, around 20% at the outlet of the slurry preheater, around 70% within the first reactor, and several percents within the successive second and third reactors were converted against supplied coal. Increase of reaction temperature led to the increase of evaporation of oil fraction, which resulted in the decrease of actual slurry flow rate and in the increase of residence time. Thus, the conversion of coal was accelerated by the synergetic effect of temperature and time. Reaction rate constant of the coal liquefaction was around 2{times}10{sup -1} [min{sup -1}], which increased slightly with increasing the reaction temperature from 450 to 465{degree}C. 3 refs., 5 figs., 1 tab.

  11. Survey of the actual state of the coal related research and development in Japan. 11; Nippon ni okeru sekitan kanren kenkyu kaihatsu jittai chosa. 11

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    NEDO is surveying the actual state of the coal related research/development in Japan to supply information on the coal related research/development in Japan to IEA`s coal research project database. This book of fiscal 1997 version includes 338 subjects. The details described are name of research institute, the section in charge, address, name of country, telephone No., name of joint researcher, research theme, classification, outline of research, project No., name of researcher, sponsor, the budget appropriated, term of research, remarks, etc. The books of data collected from each country in surveys of the actual state of the coal related R and D and IEA`s coal researches which have been made so far are submitted for general viewing at NEDO Information Center. Also, a part of those can be accessible from the energy database of which NEDO Information Center is performing on-line service for user members

  12. Survey on the feasibility of simple waste energy systems in medium or small cities; Chusho toshi ni okeru kan`igata haikibutsu riyo energy system no kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For effective use of wastes, the concept of a waste utilization system suitable for local characteristics of the Kyushu district was surveyed. The amount, features and processing method of wastes were surveyed for every kind of wastes and every region. Characteristics of wastes themselves and their use technologies were surveyed to study the energy system concept, and the concept was selected mainly for simple middle or small-scale systems. Main wastes available as heat source showed distinctive distributions every region. The following seven concepts were thus selected: RDF (refuse derived fuel) energy system mainly using general wastes, RDF system using wood chips and agricultural plastic wastes, co-generation system by premixed combustion of chicken manure and combustion improver, premixed combustion of livestock manure and combustion improver, methane fermentation using livestock, distillery and starch wastes, and pyrolytic oil system or gas system using agricultural plastic wastes. Establishment of any systems is difficult only in single region because of their economic scale. The collection and storage methods of raw materials should be studied. 36 figs., 40 tabs.

  13. New utilization and recall of carbon dioxide in domestic and foreign countries; Saikin no naigai ni okeru tansan gas no riyo to kaishu

    Energy Technology Data Exchange (ETDEWEB)

    Hanada, M.

    1994-09-01

    This paper summarizes the utilization technologies and recovery of carbon dioxide. Carbon dioxide is manufactured from such inorganic materials as carbonates and cokes, and such organic materials as hydrocarbons and alcohols. Carbon dioxide used in refreshing beverages is manufactured by sulfuric acid decomposition of sodium bicarbonate or limestone, pyrolysis of carbonates, natural gushing, and alcohol fermentation. Sodium carbonate is obtained by using the Solvay process that uses NaCl, NH3 and CaCO3 as the raw materials, but CO2 from hydrocarbons is utilized recently. The sugar industry uses slaked lime and CO2 in cleaning raw sugar concentrates. Grain size, shape, and grain size distribution of the precipitated calcium carbonate light obtained from reaction of slaked lime and CO2 are affected by reaction temperatures and concentrations. This precipitated calcium carbonate light is used in rubber filling, paper manufacturing, and plastics. South Africa and other countries manufacture gypsum for cement by using limestone and sulfuric acid as the raw materials. The annual dispersion of CO2 from fossil fuel consumption amounts to 5.2 billion tons. Discussed as its reducing measures include fixation by sea algae, adsorption, absorption and clathration by zeolite and monoethanol amine. 8 refs., 2 figs., 6 tabs.

  14. Suppression of cell metabolism y structuring water under hydrophobic-gas pressure; Sosuisei gasu atsuryokuka ni okeru mizu no kozoka wo riyo shita saibo no taisha yokusei

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, Atsushi; Kameoka, Takaharu [Mie University, Mie (Japan). Dept. of Bioinformation Scicence; Shiinoki, Yasuhiko; Ito, Kensuke [Snow Brand Milk Products Corp., Tokyo (Japan). Technical Research Institute

    1999-03-10

    We propose a new method to suppress cell metabolism by dissolving hydrophobic gas into intracellular water, and structuring it under hydrophobic-gas pressure. Xenon, krypton, argon, and helium gases show death inhibitory effects on all test bacteria (Escherichia coli, Pseudomonas aeruginosa, Bacillus subtilis, Staphylococcus aureus and Streptococcus salivarius) suspended in physiological saline with no nutrient component during storage under the conditions. In addition, different death inhibitory effects are observed among the five test bacteria, and this proposed method is more effective for gram-negative bacteria with thin cell walls than for gram-positive bacteria with thick cell walls. Further, xenon gas exhibit more significant effects for death inhibition than any other test gases, and the optimum initial partial pressure to inhibit the death is observed only for xenon gas in the present experimental conditions. Consequently, it is experimentally suggested that the cell metabolism can be suppressed almost perfectly by making the optimum water structure. (author)

  15. Studies on substitutional protein sources for fish meal in the diet of Japanese flounder; Hirame shiryo ni okeru miriyo shigen no riyo

    Energy Technology Data Exchange (ETDEWEB)

    Kikuchi, K.; Furuta, T.; Sakaguchi, I. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-08-01

    Effectiveness of livestock industry wastes and vegetable protein added to fish meal in fish farming is tested by feeding the Japanese flounder. In the experiment, a part or the whole of the fish meal protein is replaced by the meat meal (MM), meat and bone meal (MBM), corngluten meal (CGM), or dried silkworm pupa meal (SPM), and fries of the Japanese flounder are fed on the new diets for eight weeks. On a diet containing 60% or less of MM, no change is detected in the fish in terms of increase in weight, protein efficiency ratio, and blood components, indicating that 60% at the highest of fish meal may be replaced by MM. In the case of MBM, it can occupy approximately 20%. As for CGM, the proper substitution rate is approximately 40%. Essential amino acids that the new diets may lack are added for an approximately 10% improvement on the result. The SPM substitution works up to 40%, when, however, the blood components are degraded. The proper substitution rate is therefore placed at approximately 20%. 38 refs., 2 figs., 17 tabs.

  16. Wind energy technology : from the past to the future; 20 seiki ni okeru furyoku riyo gijutsu no henkan. Furyoku hatsuden : kako kara mirai e

    Energy Technology Data Exchange (ETDEWEB)

    Ushiyama, I. [Ashikaga Institute of Technology, Tochigi (Japan)

    2000-01-20

    Windmills are one of the oldest prime movers and have been used for more than 700 years in Europe. The transition from low speed windmills for grain grinding and water pumping to high speed wind turbines for electric power generation had occurred at first, reviews the windmill technologies and the researchers before 20{sup th} century. Then describes the back ground of how the wind power generator has existed and how the four pioneers developed their wind power generator. The historical developments of windmills to wind turbines in this century are studied focusing mainly on Danish activities. Then, the effort of the development of large wind turbine such as Smith-Putnum's first MW machine in U.S.A. and other mammoth machine concept are introduced. The new concept machines such as Savonius and Darrieus wind turbines in 1920s to 1930s are also explained. Finally, the novel technologies of wind turbine covering larger machines, variable speed generators, special wing sections for wind turbines, theoretical analysis method of wind turbine performance, offshore wind turbines, and wind turbine control technologies are stated. (author)

  17. Fiscal 1996 report on the environmentally friendly type coal utilization technology transfer project. Upstream field; 1996 nendo kankyo chowagata sekitan riyo gijutsu iten jigyo. Joryu bun`ya hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper reported training activities conducted in fiscal 1996 as an environmentally friendly type coal utilization technology transfer project (upstream field). For the purpose of supporting the introduction/spread of clean coal technology (CCT) in Asian and Pacific countries, the project invited engineers there to Japan, aiming at fermentation of the understanding of CCT and heightening in quality. In the manager training conducted in fiscal 1996 for managers from Indonesia, Thailand, the Philippines and China who are in charge of management of coal mines, management of coal preparation plants, and policy decision, the project had them deepen the understanding of CCT (coal preparation field). The engineers participated in the project were 6 from Indonesia, 2 from Thailand, 2 from the Philippines, and 10 from China. The training of about two weeks was conducted at Kyushu University, Wakamatsu coal utilization technology testing field of Electric Power Development Co., Mitsui Mining Co., Ikeshima Mining Works, Matsushima Thermal Power Plant, Mitsui Engineering and Shipbuilding Co., Idemitsu Kosan Co., NEDO Training Center, etc. 12 figs., 3 tabs.

  18. Fiscal 1997 report on the environment friendly type coal utilization technology transfer project. Downstream field; 1997 nendo gyomu hokokusho. Kankyo chowagata sekitan riyo gijutsu iten jigyo (karyu bun`ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of supporting the introduction/spread of clean coal technology (CCT) in countries in Asia and the Pacific, engineers of the countries concerned were invited to Japan aiming to ferment the understanding of CCT and improve abilities of them. The project was carried out by NEDO, and managed by CCUJ. It has two courses. The manager course is for policy makers, management and senior managers. By assessing CCT and presenting a menu for economical efficiency, environmental arrangement for CCT introduction is made in working out policies and planning plant/equipment investment in the future. The engineer course is for policy planners, mid-class managers and senior engineers. It proposes data on which to base a decision in working out/planning CCT facilities, and at the same time ideas by which to reduce environmental loads by management of facilities, simple improvements, etc. The number of the persons invited are 21, that is, 8 from China, 5 from Indonesia, 4 from the Philippines and 4 from Thailand. After the training, future subjects were summed up

  19. Research program for environmentally-friendly coal utilization system. Follow-up project for briquette production plants (Tanjun Enim); Kankyo chowagata sekitan riyo system donyu shien jigyo. Briquette seizo setsubi ni kakawaru follow up jigyo (Tanjun Enim)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To suppress the emission of environmental pollutants from coal utilization in Indonesia and to contribute to stable security of Japan`s energy, demonstration of clean coal technology and consolidation of diffusion base to be introduced into Indonesia have been promoted. Briquette production plant installed in the Tanjun Enim Coal Mine was examined and guided. Two kinds of high-volatile subbituminous coals are used as raw materials. Semi-cokes with volatile matter of 20% are prepared through fluidized carbonization at 480 degC. Hydrated lime or clay and binder are added to the semi-cokes, to manufacture ball briquettes by molding at room temperature. These are forcedly dried in the continuous drying furnace. In the design, 5 ton ball briquettes can be produced for an hour. Operation time is between 8 and 15 hours in a single shift. Products completely without smoke and smell can be obtained. Combustion performance of the products is remarkably superior to that of conventional products. The operation techniques of carbonization and molding processes were actively guided. To produce briquettes with further high quality, it was suggested that blending ratios and coal properties should be investigated. Inspection method for each apparatus was also guided. There was no abrasion. 13 figs., 2 tabs.

  20. Fiscal 1995 coal production/utilization technology promotion subsidy/clean coal technology promotion business/regional model survey. Study report on `Environmental load reduction measures: feasibility study of a coal utilization eco/energy supply system` (interim report); 1995 nendo sekitan seisan riyo gijutsu shinkohi hojokin clean coal technology suishin jigyo chiiki model chosa. `Kankyo fuka teigen taisaku: sekitan riyo eko energy kyokyu system no kanosei chosa` chosa hokokusho (chukan hokoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The coal utilization is expected to make substantial growth according to the long-term energy supply/demand plan. To further expand the future coal utilization, however, it is indispensable to reduce environmental loads in its total use with other energies, based on the coal use. In this survey, a regional model survey was conducted as environmental load reduction measures using highly cleaned coal which were taken in fiscal 1993 and 1994. Concretely, a model system was assumed which combined facilities for mixed combustion with coal and other energy (hull, bagasse, waste, etc.) and facilities for effective use of burned ash, and potential reduction in environmental loads of the model system was studied. The technology of mixed combustion between coal and other energy is still in a developmental stage with no novelties in the country. Therefore, the mixed combustion technology between coal and other energy is an important field which is very useful for the future energy supply/demand and environmental issues. 34 refs., 27 figs., 48 tabs.

  1. Fiscal 1998 result report on the support and diffusion projects on introduction of environment-friendly coal utilization systems. Fiscal 1998 joint demonstration project for the CMG recovery/utilization system; 1998 nendo kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo seika hokokusho. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report is the summary of the basic plan for the demonstration project for the CMG (coal mine gas) recovery/utilization system conducted by Tiefa Coal Mining Administration in 1998-2002. The project site is Tiefa mining property, and the plan includes the introduction program of Japanese technology for the CMG recovery/utilization system. The gas recovery plan was prepared for both Daxing and Daming One mines. The technology and facility introduced from Japan are as follows: 300m middle- class horizontal gas drainage drilling technology and facility, gas transfer technology and facility from gas drainage holes, fly ash sealing and sealed gas drainage technology and facility, measurement for gas transfer pipes, automatic sealed gas drainage technology and centralized monitoring, and automatic gas drainage facility. Recovered gas is supplied to Tiefa city and Tieling city as city gas, and this plan includes the gas supply facility to Tieling city. Gas is recovered from all coal mines in Tiefa mining property. A gas utilization rate of 32%, reduction of gas emission of 0.1% at mining faces, and reduction of gas drainage drilling lengths are estimated. (NEDO)

  2. Report on achievements in proliferation project to introduce environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998; Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This paper describes the discussion report for fiscal 1998 on the CMG (coal methane gas) recovery and utilization project to be implemented from fiscal 1998 through fiscal 2002 at Tiefa Mining Bureau of Liaoning Province in China. The Daixing mine was selected as the survey object. The introduced technologies and facilities include test drilling for degassing (medium measure horizontal degassing of 300-m class), induction from degassing holes, fly ash sealing, sealed gas degassing, surveillance and control technologies and facilities. The recovered gas is to be supplied to the cities of Tiefa and Tieling as town gas, for which compressed gas feeding and controlling technologies and facilities will be introduced. This paper lists the gush-out quantity (1,000 Nm{sup 3}), the recovery quantity (1,000 Nm{sup 3}), the recovered gas concentration (%), the utilization quantity (1,000 Nm{sup 3}), and the utilization rate (%). The figures for the respective items before and after the implementation are 128366, 32949, 44.5, 7000, 5, 123500, 43890, 49.1, 39826, and 32. The quantity of gas gushing out at facings decreases in association with increase in the recovered gas quantity, whereas the gas concentration at facings in the Daixing mine in 2003 is estimated to decrease to 0.1%, contributing to safe mining operation. The test drilling for medium measure horizontal degassing expands the degassing assured scope per one test drilling seat, and can reduce the total test drilling length and construction amount. (NEDO)

  3. Effect of intermolecular cohesion on coal liquefaction. 3. Reactivity of oxygen methylated coal; Sekitan teibunshika hanno ni okeru bunshikan gyoshuryoku no koka. 3. O-methyl ka tan no hanno tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, M.; Nagaishi, H.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-10-28

    The reactivity of oxygen methylated coal was studied to control hydrogen bond in bituminous coal liquefaction and intermolecular cohesion such as van der Waals force. In experiment, crushed and dried Illinois coal of 100mesh or less was used as specimen, and oxygen methylated coal was prepared by Liotta`s method using tetrabutylammonium halide. Coal liquefaction was conducted in an electromagnetic agitation autoclave using tetralin solvent under initial hydrogen pressure of 100kg/cm{sup 2} while heating. The molecular weight distribution of the products obtained was measured by gel permeation chromatography (GPC) analysis. The experimental results are as follows. The effect of intermolecular cohesion in bituminous coal on the reactivity is mainly derived from decomposing reaction from preasphaltene to oil. Yields of oil fraction by methylation increase corresponding to release of intermolecular cohesion. Since the thermal release is promoted with temperature rise, the difference in yield due to different treatments decreases. 5 refs., 3 figs., 1 tab.

  4. Coliquefaction of coal, tar sand bitumen and plastic (interaction among coal, bitumen and plastic); Sekitan/tar sand bitumen/plastic no kyoekika ni okeru kyozon busshitsu no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, H.; Okuyama, Y.; Matsubara, K. [NKK Corp., Tokyo (Japan); Kamo, T.; Sato, Y. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    For the improvement of economy, coliquefaction of coal, tar sand bitumen and plastic was performed under low hydrogen pressure, to investigate the influence of interaction among these on the liquefaction characteristics. For comparison, coliquefaction was also performed under the hydrogen pressure same as the NEDOL process. In addition, for clarifying its reaction mechanism, coliquefaction of dibenzyl and plastic was performed as a model experiment, to illustrate the distribution of products and composition of oil, and to discuss the interaction between dibenzyl and various plastics, and between various plastics. Under direct coal liquefaction conditions, coprocessing of Tanito Harum coal, Athabasca tar sand and plastic was carried out under low hydrogen pressure with an autoclave. The observed value of oil yield was higher than the calculated value based on the values from separate liquefaction of coal and plastic, which suggested the interaction between coal and the mixed plastic. The results of coliquefaction of coal, tar sand bitumen and plastic could be explained from the obtained oil yield and its composition by the coliquefaction of dibenzyl and plastic. 2 refs., 3 tabs.

  5. Fiscal 1994 survey of the base arrangement promotion for foreign coal import. Investigation on the trend of coal demand in Central and South American countries; 1994 nendo kaigaitan kiban seibi sokushin chosa. Chunanbei shokoku ni okeru sekitan jukyu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Focusing on the present status and future of coal demand in Central/South American countries and the coal trade between Central/South American countries and the U.S., the paper described the present status and future of coal demand there and the effects on Japan. Export of Colombian coal will amount to approximately 30-35 million tons in 2000. Venezuelan coal 10-20 million tons. The U.S. imported good-quality general coal low in sulfur content, 3.08 tons from Columbia and 1.39 tons from Venezuela. Coal export from the U.S. to Central/South America was mostly of raw material coal, 5 million tons in 1993 and 5.39 million tons in 1994. General coal was 180,000 tons. The U.S. has no plans of increasing US coal export to Central/South America. But it is safely predicted that Columbia and Venezuela will increase coal export to Europe in the future. It will bring about decrease in export of US coal to Europe, which connects with increasing pressure for the coal trade amount of Japan. 21 figs., 47 tabs.

  6. Utilization of two-way multicore cables and comparison of various electrode configurations in electrical prospecting; Denki tansa ni okeru sohokogata tashin cable no riyo to kakushu dekyoku haichi no hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Takakura, S. [Geological Survey of Japan, Tsukuba (Japan); Matsushima, J. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1996-10-01

    For more precise electrical prospecting, the new multicore cable was developed to allow high-density measurement by conventional equipment. Since conventional multicore cables are inferior in cost, length and weight, the new cable is composed of an n-conductor cable, two n-conductor male connectors and n lead wires. For connection of the multi-conductor cable and lead wires, cable sheath is peeled at n points at specific intervals. Sheath of the k-th conductor is peeled at k-th point from the terminal, and restored for insulation after connection of the conductor and lead wire. The male connectors are attached to the both ends of the multi-conductor cable. Since this two-way type cable can be used at every end, the measuring equipment can measure at one divisional point after another of a long measuring line while shifting the equipment from one point to another. All measurements are perfected only with two short cables. Resistivities were successfully measured along the long measuring line of 480m long with 97 electrodes arranged at intervals of 5m. Various electrode configurations were also compared. 1 ref., 4 figs., 2 tabs.

  7. Fiscal 1999 report on basic research for promotion of joint implementation programs. Research on collection and utilization of coal mine methane gas in Russia (Kuznetsk coal field); Russia (Kuznetsk tanden) ni okeru tanko methane gas kaishu riyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The above-mentioned effort is to comply with the COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) joint implementation clause. At this coal field, mining facilities are growing superannuated and obsolescent in the prolonged business depression, causing frequent occurrence of disasters such as gas explosions. The coal mine gas collection rate at the Kuznetsk coal field is as low as 17%, with concern for safety discouraging sufficient collection. Even the small amount of the collected gas is, in the absence of gas utilizing facilities, totally discharged into the air. For the mitigation of global warming, for mining safety, and for the establishment of a foundation for business, it is desired that coal mine methane gas collection/utilization facilities and related technologies be introduced into the coal field. Gas purging from the pits is incomplete, which is attributed to the lack of equipment capable of excavating proper-diameter bores longer than 100m for longwall mining. Ventilation also needs improvement. The research is under way on the premise that highly reliable intermediate range (300m) boring equipment and gas management technologies will be available. Collection of gas of a 30-35% concentration level at a collection rate of 40% is the target. (NEDO)

  8. Research report for fiscal 1998 on the basic research on the promotion of joint implementation and so forth. Coalbed methane collection and utilization project in China; 1998 nendo Chugoku ni okeru tanko methane gas kaishu riyo project chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    China is surveyed for promotion of joint implementation, which is one of the flexibility measures in the Kyoto Protocol, the Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change. The project aims to collect methane for global warming suppression and to use it as town gas and for power generation as well. The survey covers the 2 coalfields of Yangquan and Panjiang. The Yangquan coalfield is the largest anthracite yielding base in China, with 6 mines in operation. Power generation centering on a 100MW plant is discussed, and generation fired by a mixture of debris out of the coal preparation facility and gas is compared with another fired by town gas, on the assumption that 130-million m{sup 3} is available under the current circumstances. In the case of the Panjiang coalfield, which is expected to develop into a large coal base in the southern part of China, power generation centering on a 50MW plant fired by a mixture of debris and gas is discussed, on the assumption that 63-million m{sup 3} is collectable from the existing 5 mines. Use of town gas is also studied. When Japan's coalbed methane collection technology is applied, the gas drainage rate will be elevated to 40-35% or higher. It is desired that the use of gas drainage will be further diffused for the prevention of disasters of coal mine gas explosion. It is hoped that the use of environmentally friendly energies will be enhanced. (NEDO)

  9. Study and utilization of water-dominated and low-temperature geothermal fields in Italy; Itaria ni okeru nessui takuetsugata oyobi teion chinetsu shigen no kenkyu to riyo jokyo

    Energy Technology Data Exchange (ETDEWEB)

    Yasukawa, K. [Geological Survey of Japan, Tsukuba (Japan)

    1998-06-15

    This paper reports the state of research and development of hot-water dominated and low-temperature geothermal resources in Italy. Geothermal explorations and studies are conducted by the Italian electric power company ENEL and the International Geothermal Research Institute, of which the development of geothermal power generation is carried out by ENEL. Hot water dominated geothermal fields in the central Italy include the Tuscany area having Larderello south of Firenze and the Monte Amiata area, the Latium area around Rome, and the Campania area around Napoli. Low-temperature geothermal fields in the northern Italy include Ferrara, Vicenza, Euganei Hills, and Aqui Terme. A large number of wells have been drilled to as deep as 3000 m in high-temperature geothermal areas for power generation. The present drilling is targeted exclusively at deep reservoirs. In the hot water dominated areas in the central Italy, power plants of 20-MW class are built even in areas with not too high productivity, where waste hot water is utilized in binary cycle. In the northern low-temperature geothermal area, warm water is utilized directly. 8 refs., 14 figs.

  10. Fiscal 1999 technical survey report. Model project implementation feasibility study in Malaysia on effective utilization of waste heat from paper sludge incineration; 1999 nendo Malaysia ni okeru seishi sludge nensho hainetsu yuko riyo model jigyo jisshi kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are under way to popularize practical energy conservation technologies through verification on real machines in target countries. Possibilities were studied that Malaysian paper making plants would adopt technologies of collecting heat from high-temperature exhaust gas from paper sludge incineration and of effectively utilizing the thus-collected heat. The Malaysian paper making industry produced 800-thousand tons or more in 1998, covering 72% of the total national demand. Heat recovery facilities may be installed in 15 plants. On-site surveys were made into their actual states, and then Genting Sanyen Industrial Paper Sdn. Bhd. was selected as the plant for the model project, and detailed model project feasibility studies were conducted. The studies covered the amount of wastes from paper making, their properties, treatment process, amounts of utilities to be used during system operation, land on which to build the facilities, and a plan for collecting invested funds. As the result, it was concluded in view of the magnitude of the expected fruit that the model project be implemented at this plant. (NEDO)

  11. Study on management of resource and environment in poverty areas. Examples of agriculture and water use in bangladesh; Hinkon chiiki ni okeru shigen to kankyo no kanri ni kansuru kenkyu. Banguradeshu no nogyo to mizu riyo wo rei to shite

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, Hiroyuki [Kinki University, Osaka (Japan). Faculty of Agriculture

    1998-12-16

    This paper describes the main features of flood plains and fish production related to agriculture in the vast inland water areas of Bangladesh. The inland fisheries have been an important source of animal protein and provided employment opportunities for rural Bangladeshies. Generally the fishermen's economic conditions are below the poverty line in this country. Fishi production in the inland water areas are not met to the basic needs of the people on a sustainable basis. While inland fishery is important for business as well as for people's livelihood, it is not usually managed appropriately for resource conservation and environment. Fishery policies and planning have to be undertaken for comprehensive long-term perspective in order that agricultural and other sectors would not contaminate the environment. (author)

  12. Development of hydroponic system using agricultural waste. 2. Utilization of ozone for sterilization of nutrient solution; Suiko saibai ni okeru haikibutsu riyo gijutsu no kaihatsu. 2. Ozone ni yoru baiyoeki sakkin ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Terazoe, H.; Yoshihara, T.; Nakaya, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1995-08-01

    Discussions were given on a sterilizing effect of ozone on Fusarium bacteria in hydroponic culture, and its effect on components in the culture solution. In an experiment, dry air with O3 concentration of 3.5 ppm was sent into aqueous solution inoculated with Fusarium bacteria at a flow rate of 5 liters per minute. The Fusarium bacteria was sterilized nearly completely in about five minutes. No change was observed in pH, EC and dissolved oxygen concentration of the O3-treated culture solution. However, iron and manganese among the soluble components have been oxidized by O3 and precipitated, hence these components must be added after the O3 treatment. In spinach culture performed on a culture medium inoculated with Fusarium bacteria, ozone water containing dissolved O3 at 0.8 ppm was flown into a urethane foam medium and vegetable roots. This treatment has resulted in reduction of the number of strains occurred with a wilt symptom below that in the section flown with distilled water. The spinach has grown normally without showing an effect of the ozone water. 15 refs., 10 figs., 3 tabs.

  13. Borehole geophysics for delineating the geological structure in the Sakonishi prospect, the Hida area, Japan; Hida chiiki Sako nishi chiku ni okeru boring ko riyo butsuri tansa ni yoru chishitsu kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Katayama, H.; Hishida, H.; Yoshioka, K. [Metal Mining Agency of Japan, Tokyo (Japan)

    1997-05-27

    In order to discuss effectiveness of physical exploration in the Sakonishi prospect in the Hida area, physical exploration was carried out by utilizing bored wells. This area contains the Kamioka mine, one of the major base metal mines in Japan, where electrical exploration has been attempted several times in the past. No effective results have been obtained, however, because specific resistance contrast between mine beds and base rocks is too small, and the topography is too steep making site workability inferior. As part of the investigations on geological structures over wide areas, electrical logging (specific resistance and natural potential) was performed in fiscal 1995 and 1996 by utilizing the boreholes. Induced polarization logging was also conducted on the same boreholes. A traverse line on the ground with a length of 600 m and boreholes were used to execute specific resistance tomography. Clear extraction was possible on a fault structure which is thought related with limestone distribution and mine bed creation. However, it was not possible to identify upward continuity of zinc ores expected in the exploration. Because of not large a specific resistance contrast between zinc ores and base rocks, it is difficult to find mine bed locations only from the information on the specific resistance. 5 refs., 5 figs., 1 tab.

  14. Aspiration toward geothermal energy utilization in regional development plan. Part 6. ; Hydrothermal fluid utilization business in Matsuo-mura of Iwate prefecture. Chiiki keikaku ni okeru 'chinetsu riyo' eno hofu. 6. ; Iwateken Matsuomura no chinetsu nessui riyo jigyo

    Energy Technology Data Exchange (ETDEWEB)

    Otobe, Y.; Furutate, E.

    1992-10-31

    Twenty six years have passed since the first geothermal power station was constructed in Matsuo-mura of Iwate Prefecture, Japan. This paper describes the history, the present situation and the future conception of the geothermal energy utilization in this village. This village includes Hachimantai of a vantage ground in the center and has the gross area of 233.8km[sup 2], the annual average temperature of 8.3 centigrade and the continuous snow cover period of about 100 days. The hot water leading facility was cooperatively constructed by Japan Metals and Chemicals, Hachimantai Hot Spring Development and Matsuo-mura. The total working expense is 539.3 million yen. Hot water sources are the condensate from the condenser of geothermal power plant and hot spring. This mixed hot water of 4.3 t/min is led to respective facilities. The hot water supplying channel has the length of 12.8km from the power station through the Hachimantai hot spring resort, Kamiyogi to Takaishino. Respective total areas of greenhouses using hydrothermal fluid in both districts are 1,075ha and the inlet temperature of hot water is 60 centigrade and kinds of crop are 5 like green pepper and others. Takaishino agricultural park has selected flower and ornamental plant culture such as poppy anemone, stock and statice which are suitable for this district of low temperature and insufficient sunshine. The planted area is 10,700m[sup 2]. 2 refs., 9 figs., 4 tabs.

  15. Present status of and subjects on the industrial utilization of polymer separation membranes. Japan`s first largest sea water desalination plant by RO; Kobunshi bunrimaku no sangyo riyo no genjo to kadai. Zosui bun`ya ni okeru maku riyo

    Energy Technology Data Exchange (ETDEWEB)

    Furuichi, M. [Kurita Water Industries Ltd., Tokyo (Japan)

    1998-07-05

    The utilization in Japan and abroad is discussed of desalination methods using evaporation, reverse osmosis (RO) membranes, and electrodialysis membranes, out of various desalination techniques for seawater and others containing more salt. A new seawater desalination plant built in Okinawa, Japan, is outlined, and the future trend of Japan`s efforts for desalination is predicted. The said plant in Okinawa is the largest ever built in this country, and occupies 4th or 5th place in terms of capacity among similar facilities across the world. It was completed in April, 1997, and produces pure water at a rate of 40,000m{sup 3}/day. This plant, operating on RO, comprises eight RO membrane units each capable of 5131{sup 3}/day. The membranes are of the spiral type, consisting of Toray`s crosslinked aramid-base composite membranes and Nitto Denko`s membranes composed totally of crosslinked aromatic polyamide. The greatest of the pending tasks is to reduce the desalination cost. As for the operating cost of the desalination facility at the current stage, it costs 120-130 yen/m{sup 3} on the 40,000m{sup 3}/day scale, and the power cost occupies approximately 60% of the total operating cost. It is concluded that the consumption of electric power and chemicals per pure water produced have to be reduced. 8 refs., 5 figs., 5 tabs.

  16. Report on the results of the fiscal 1998 survey of arrangement/promotion of the overseas coal import base. Model survey for high level coal utilization promotion models (survey of the present and future situation of coal energy after COP3); 1998 nendo kaigaitan yunyu kiban seibi sokushin chosa (sekitan kodo riyo sokushin model chosa). COP3 iko no sekitan energy no genjo oyobi shorai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    For the purpose of contributing to the future coal industrial policy of Japan, an investigational study was conducted on the nature of coal as resource, the production/utilization status, policies of other countries, etc. The coal demand during the period of 1991 through 1995 rapidly increased in Asia, slightly rose in North America, decreased in East and West Europe, and largely declined in the former U.S.S.R. The energy demand showed a large growth rate with the economic growth in developing Asian countries in and after the 1980s as a background. The power demand which supports the economic growth will continue to improve. It connects with the coal demand in Asia, and the coal demand seems to rapidly increase. Further, the global warming issue became a great matter of concern in the 1990s. Coal, which emits more CO2 per unit calorific value than oil and natural gas, is not a powerful candidate for petroleum substituting energy as used to be regarded, but became a bad thing. Moreover, recently the economic stagnation in Asia which was triggered by the currency crisis has long been continuing, and it started to appear that the coal consumption will possibly fall very short of the prediction. The future is unclear. 20 refs., 25 figs., 39 tabs.

  17. Survey for making a data book on the new energy technological development. Waste-fueled power generation, solar heat utilization, geothermal power generation, clean energy vehicles, coal liquefaction/gasification, and traversal themes; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Haikibutsu hatsuden, taiyonetsu riyo, chinetsu hatsuden, clean energy jidosha, sekitan ekika, gas ka oyobi odanteki tema

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper concerns the following six fields among the fields of new energy technology: the waste-fueled power generation, solar heat utilization, geothermal power generation, clean energy vehicles, coal liquefaction and coal gasification. The up-to-date data made public were collected and classified into the following items: outline of systems, specific examples of the introduction in Japan and other countries, policies/laws and rules/subsidy systems, production quantity/actual amount of introduction/projected amount of introduction (target), cost, terminology, listing of main related companies and groups, etc. Further, arrangement was traversally conducted on the outlook of the energy introduction by the Japanese government and measures taken for development of new energy by Japan and other countries. Namely, the items of the book are as follows: classification of new energy, outlook for energy supply/demand, cost of new energy technology (power generation) and outlook for the introduction, menus of buying surplus electricity of electric companies, policies/laws and rules/subsidy systems concerning the new energy introduction in Japan and overseas, and a list of organizations engaged in the new energy technological development.

  18. Fiscal 1997 report on the survey for a data book on new energy technology development. Waste power generation, solar energy utilization. geothermal power generation, clean energy vehicles, coal liquefaction/gasification, and traverse themes; 1997 nendo chosa hokokusho. Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (haikibutsu hatsuden, taiyonetsu riyo, chinetsu hatsuden, clean energy jidosha, sekitan ekika gas ka oyobi odanteki theme)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper collected and arranged data on new energy technology. As to the waste power generation, in terms of general waste, 161 places have power generation facilities, 657,000 kW in output, as of the end of FY 1996. Out of them, 100 facilities (scale of output: 555,000 kW) are selling power. In terms of industrial waste, 53 places (209,000 kW) have power generation facilities. The output will be 2 million kW in FY 2000. In relation to the solar energy utilization, the number of solar systems introduced in FY 1996 is 25,000, that of water heating appliances produced in FY 1996 is 170,000. Geothermal power of 494,000 kW and 37,000 kW was introduced for electric power industry use and private use, respectively. Clean energy vehicles have not been so much spread, but the hybrid car was put on sale in 1997. Concerning the coal liquefaction, the R and D were made at a pilot plant of NEDOL process, and operation started in 1997. As to the coal gasification, investigational study and element study on the demonstration plant are being conducted in FY 1997 and 1998, making use of the research results obtained from the existing pilot plant of coal gasification combined power generation

  19. FY 1999 report on the results of the project for supporting the introduction of the environmentally friendly type coal utilization system. Follow-up project on the simplified desulfurization facilities (Thailand); 1999 nendo kankyo chowa gata sekitan riyo system donyu shien jigyo. Kan'i datsuryu setsubi ni kakawaru follow up jigyo (Tai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    The follow-up was conducted of the project for supporting the introduction of the environmentally friendly type coal utilization system and demonstrative project on simplified desulfurization facilities which were carried out with the aim of reducing environmental loads associated with the coal utilization in Thailand, and the FY 1999 results were reported. As to the follow-up project, survey was made of the operation state of the simplified flue gas desulfurization (FGD) system, and at the same time, the following were carried out at the time of periodic inspection/repair: examination of/guidance for maintenance, and welding repair guidance for the corroded spots of flue. Thai Union Paper Public Co. (TUP), which had already acquired ISO14001, is a model company earnestly tackling the environmental improvement. Approximately 400 persons per year visit to see the FGD system. About 3 and a half years have passed since the FGD system started operation. Scaling of gypsum, etc. and corrosion at some part were seen, but the whole plant is in smooth operation. As a result of the analysis, purity of the recovered gypsum was approximately 90%, and therefore, that is very usable as raw material of cement. The progress of corrosion and increase of corroded portions were hardly recognized as compared with those in the previous fiscal year. (NEDO)

  20. FY 1999 report on the results of the joint demonstrative project on the environmentally friendly type coal utilization system. Demonstrative project on the low grade coal combustion system - Zhejiang Huba Group Co.; 1999 nendo kankyo chowa gata sekitan riyo system kyodo jissho jigyo. Teihin'i tan nensho system ni kakawaru jissho jigyo (Yoko Koha shudan koshi)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The demonstrative project on the low grade coal combustion system that makes the reduction of sulfur oxide emissions possible was conducted jointly with China taking a positive attitude to the introduction of the low grade coal combustion technology, and the FY 1999 results were reported. As to the low grade coal combustion system, low grade coal is burned using the circulating fluidized bed boiler which burns coal by uniform mixture/circulation of coal and particles (limestone, ash, etc.) In this fiscal year, the design/manufacture were made of electric instrumentation equipment, electrostatic precipitator, boiler structuring accessory equipment, etc. Further, by supervisors sent to China, technical guidance/supervision were given for the installation work and trial operation. As to the training of operators, by engineers sent to China, training/guidance were given using a leaflet of the gist of trial operation, explanatory leaflet of handling, leaflet of the gist of maintenance/inspection, etc. The test to confirm boiler efficiency was made on September 27, 1999, and confirmed the predetermined performance. The demonstrative test was conducted continuously till March 2000 and demonstrated the practical applicability of the low grade coal combustion and reduction in environmental loads using the circulating fluidized bed boiler. (NEDO)

  1. Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project on simplified desulfurizers; 1997 nendo seika hokokusho. Kankyo chowagata sekitan riyo system donyu shien jigyo (kan`i datsuryu setsubi ni kakawaru jissho jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To reduce SOx with coal utilization, a desulfurizer is introduced in Thailand as diffusion activities in the demonstration program. The purpose is to reduce the environmental pollutants. For this desulfurizer, lime mud mainly composed of lime stone is used as an absorber. SO2 in the flue gas is absorbed by the slurry of lime mud, to form calcium sulfite. The calcium sulfite blown in the bottom of recycling tank is oxidized by oxygen in the air, to form gypsum. The gypsum is recovered as a by-product. In this fiscal year, a feeder of lime stone, spray nozzles, and various analysis apparatuses were supplied. Supervisors for electric instrumentation/control were also dispatched as well as for main body construction, to carry out the instrumentation setting works, check of sequences, and adjustment of apparatuses. After the test operation, supervisors for the demonstration operation were dispatched up to March 1998, to conduct the cooperation works between Japan and Thailand sides. Thus, successful and successive demonstration operation was confirmed. 21 figs., 6 tabs.

  2. FY 1999 report on the results of the project for support of introduction of the environmentally friendly type coal utilization system. Demonstrative project on the circulating fluidized bed boiler equipment (Zaozhuang mining department, Chaili coal mine); 1999 nendo kankyo chowagata sekitan riyo system donyu shien jigyo. Junkan ryudo yuka boira setsubi ni kakawaru jissho jigyo (Soso komukyoku Sairi tanko)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of contributing to the control of emissions of the environmental pollutants associated with the coal utilization and the effective use of energy in China, the demonstrative project was carried out for installation of the circulating fluidized bed boiler, activities for the spread, etc., and the FY 1999 results were reported. As to the trial operation of the boiler partial load zone (40-50%) conducted from October 16 to November 20, 1999, the operation was obliged to be discontinued by the biting of the equipment by foreign substances mixed into the fuel, mixture of low grade oil into the light oil tank for start-up, fixing inside the furnace caused by burning of low grade oil, fluctuations in the water content of fuel sludge, etc. Concerning the trial operation that started on March 2, 2000, operational maintenance of boiler and auxiliary equipment was conducted during the trial operation by China-side persons to confirm the results of the training. Relating to the test to confirm boiler performance made on March 9, by the sampling/analysis of fuel, combustion ash, etc., it was confirmed that specifications for boiler performance were satisfactory. After finishing the trial operation, through the inspection of each part of the plant, it was confirmed that there were no anomalies. (NEDO)

  3. Report on investigations in fiscal 2000 on the projects to support introduction of environment friendly coal utilization system. Green helmet project for briquette production plant - Mae Moh coal mine, Thailand; 2000 nendo kankyo chowagata sekitan riyo system donyu shien jigyo chosa hokokusho. Briquette seizo setsubi ni kakawaru green helmet jigyo (Thai koku Mae Moh tanko)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    This Green Helmet Project is intended to suppress generation of environment polluting substances in association with coal utilization in Thailand by demonstrating and improving the proliferation infrastructure for the clean coal technology to be used widely in Thailand. The project is also intended to serve for stabilized assurance of energies for Japan. The demonstration project related to briquette manufacturing facilities executed as one of the 'Projects to support introduction of environment friendly coal utilization system' is intended to manufacture at low cost a briquette which is low in odor, free of smoke, and suppressed largely of sulfur oxide generation. The briquette is made by adding clayish minerals, sulfur, a fixing agent and a binder into brown coal being a low grade coal. The project implements proliferation of the technology to reduce environmental load associated with coal utilization in developing countries according to the situation and needs of the counterpart countries. The present project has performed the site surveys and guidance of operation and maintenance techniques as follow-up works of the demonstration project having been completed by cooperation between Japan and Thailand. It is considered that what had been intended in the beginning has been achieved sufficiently. (NEDO)

  4. Fiscal 2000 report on basic survey of coal resource development. Information collection and analysis project (Technical cooperation project on coal mine methane gas recovery and utilization); 2000 nendo sekitan shigen kaihatsu kiso chosa (joho shushu kaiseki jigyo) hokokusho. Tanko methane gas kaishu riyo gijutsu kyoryoku jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A survey was conducted to construct a simulation technique for predicting changes in the behavior of gas to accompany digging in Australian coal mines. The survey activities were conducted in the mining area of the Wambo colliery in the Hunter valley, New South Wales, which involved the acquisition of geotechnological data including the amount of coal reserves and the amount of methane gas held in the coal seams, drilling of 19 test bores (with cores sampled from some of them), geophysical logging of the test bores, seismic exploration, analysis of the sampled cores, rock tests, modelling of the geological structure, testing of gas from the coal seams, modelling of the state of existence of the gas, and so forth. It was found that the amount of gas held in the coal seams at levels 200m or deeper was larger than 9m{sup 3}/t. Existing software programs were examined as to whether they could be used for the preparation of a gas behavior simulation program, and it was found that none of them was capable of helping the simultaneous simulation of rock deformation due to drilling and the resultant change in multi-phase gas behavior. The conclusion was that it was necessary to newly develop a comprehensive simulation software program. (NEDO)

  5. Fiscal 1999 survey report. Basic survey for development of coal resources - project for information collection and analysis (technical cooperation project for recovery and utilization of mine methane); 1999 nendo sekitan shigen kaihatsu kiso chosa (joho shushu kaiseki jigyo) hokokusho. Tanko methane gas kaishu riyo gijutsu kyoryoku jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The purpose of this project is to reduce environmental load by investigating the recovery/utilization technologies of mine methane gas, to build predictive simulation for the behavioral change in methane gas that is incidental to underground mining, and to reflect the simulation on the optimum mining plan. Performed in the survey this year were the information collection/analysis of the coal and gas resources, exploratory boring for the purpose of grasping the geology, coal bed and gas abundance in the selected survey sites, measurement of coal bed gas reservoir, and the survey of geotechnological features. The operations were as follows; collection of existing geological data and selection of exploratory boring sites for Arrowfield layers and Bowfield layers in the Hunter Valley region. The coal bed gas reservoir and the composition of the coal cores obtained in eight borings this year provided precious gas data along with the survey results performed in the subject sites in the past. In particular, significant data necessary for depth coal development were also obtained in the surrounding mines including the subject survey sites. It was confirmed that the gas reservoir in the coal bed was 8 m{sup 3}/t to 9 m{sup 3}/t on the average. (NEDO)

  6. Survey for preparing the database for R and D of new engines. Waste power generation, solar heat system, geothermal power generation, clean energy vehicle, coal liquefaction/gasification, and combined systems; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Haikibutsu hatsuden, taiyonetsu riyo, chinetsu hatsuden, clean energy jidosha, sekitan ekika gas ka oyobi odanteki tema

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The present developmental conditions and issues of new energies are systematically arranged for effective promotion of their diffusion. One hundred and forty six general waste power generation facilities of 558,000kW are in operation in 1995, and among them 89 facilities supplies 1,080 GWh to power companies. 50 industrial waste power facilities of 247,000kW are in operation. 20,000 solar systems and 180,000 hot water heaters are in operation in 1995. Commercial geothermal power generation facilities of 490,000kW and private ones of 36,000kW are in operation. Introduction of expensive clean energy vehicles is making very slow progress. The pilot study on bituminous coal liquefaction is in promotion mainly by NEDO. The experiment of entrained bed coal gasification in Nakoso was successfully completed, and development of a commercial plant is to be expected. Power rates of 10 power companies were reduced in 1996, and unit purchase prices of surplus power of photovoltaic and wind power generation were also revised. The new menu and unit purchase price were announced in 1996 for surplus power of waste power generation and fuel cell. 67 figs., 284 tabs.

  7. Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Follow-up project on simplified desulfurizer introduction (Weifang Chemical Industry Works); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system donyu shien jigyo (kan`i datsuryu setsubi ni kakawaru follow up jigyo (Weifang kakohei))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To reduce SOx with coal utilization, demonstration projects including diffusion activities of desulfurizers have been conducted. To promote the results of projects, experts for simplified desulfurizers were dispatched, to guide and advise for the operation of facilities introduced in these projects. The purpose of these projects is to diffuse the clean coal technologies, and to support the promotion of environmental measures. The operation conditions of facilities introduced in these projects were surveyed, to provide some guidance and advice for the operation and maintenance. Through the guidance and advice for operation and maintenance, methods of inspection and repair of resin linings at absorbing tower and flue were guided, methods of disassembly/inspection and used part replacement of rotary machines were guided, and screening surveys of absorber, mist eliminator and piping tower were carried out. For the operation techniques, application operation at emergency was not skilled. For the maintenance techniques, understandings were not enough for the equipment configuration and machineries. Nevertheless, these projects are successfully conducted, and the conditions of demonstration operations are satisfied. 33 figs., 2 tabs.

  8. Fiscal 1995 survey of the base arrangement promotion for foreign coal import. Investigation on the policy of coal demand stabilization using low grade coal; 1995 nendo kaigaitan yunyu kiban sokushin chosa. Teihin`itan riyo ni yoru sekitan jukyu anteika hosaku ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper investigated the trend of and the needs for low grade coal utilization and the seeds of low grade coal utilization technology and studied usability of low grade coal in the future. Importance of low grade coal utilization was described in consideration of features of the Asia/Pacific area in the world coal market, and the trend of production/utilization of low grade coal was examined mostly in countries holding main low grade coals in the Asia/Pacific area. The trend of the technical development contributing to the low grade coal utilization was studied to make it contribute to the extraction of technologies which are regarded as effective in the Asia/Pacific area. A study was made of applicability of the low grade coal utilization technology corresponding to the needs for low grade coal utilization, and at the same time, a study was made of the effect on the coal supply/demand in the Asia/Pacific area in case the low grade coal utilization is promoted helped by the study. Focusing on technical cooperation relating to clean coal technology, a study was conducted of the trend of international cooperation in Japan and various overseas countries and the trend of new cooperation in private sectors, and a discussion was made on how Japan should act toward promotion of low grade coal utilization. 12 figs., 91 tabs.

  9. Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project of circulating fluidized bed boiler (Jinzhou Coal-Thermal Power Corporation); 1997 nendo seika hokokusho (kankyo chowagata sekitan riyo system donyu shien jigyo). Junkan ryudosho boiler ni kakawaru jissho jigyo (Jinzhou netsuden sokoji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To verify the clean coal technology to be diffused in China and consolidate its diffusion basis, demonstration project of circulating fluidized bed boiler was conducted through the cooperation with China which is positive in its introduction. This report describes its characteristics. Coal and limestone are supplied in a lower part of combustion chamber, and are mixed with circulating ash by fluidized air for combustion. Densely fluidized bed the same as the bubbling fluidized bed is formed in the lower part of combustion chamber, which provides excellent stability in ignition and combustion. Particles including ash, char and limestone formed during the combustion are discharged into the cyclone through the convection heat transfer part at the outlet of combustion chamber with the combustion gas flow. Since the gas temperature is lowered to 400 to 500degC at the convection heat transfer part, troubles of the ash circulating system can be prevented. The combustion gas separated from ash at the cyclone is discharged through the heat exchanger and precipitator, and the collected ash is returned to the lower part of combustion chamber. In FY 1997, design, fabrication, procurement/inspection, field survey/meeting, survey of visitors/meeting, and education were carried out. 4 figs., 4 tabs.

  10. Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Follow-up project on circulating fluidized bed boiler introduction (Calaca Batangas Thermal Power Station); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system donyu shien jigyo (junkan ryudosho boiler ni kakawaru follow up jigyo (Calaca Batangas karyoku hatsudensho))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the follow-up project, to promote the diffusion of results of the clean coal technology (CCT) model projects, experts of circulating fluidized bed boilers were dispatched, to guide and advise for the operation of facilities introduced in these projects. The purpose of these projects is to diffuse the CCTs, and to support the promotion of environmental measures. Some guidance and advice about operation processes, data processing, operation regulation, maintenance, and boiler maintenance works were provided to the Ministry of Energy and Electric Power Corporation of the Philippines. Semirara, Malangas, and Samar coals in the Philippines were used for the tests. The boiler facilities could be operated by Philippine operators themselves. Based on the guidance and advice about operation processes, combustion tests using various Philippine coals were also planned and conducted by themselves. The maintenance techniques were transferred to Philippine operators through the inspection, repair and advice. The Philippine side understood the technologies well, and the circulating fluidized bed boiler technology was independently educated in the Philippines. 23 figs., 16 tabs.

  11. Survey of technological advancement of coal exploitation in Asia and Pacific for fiscal 1997. Formulation of production plans for model coal mines in China; 1997 nendo Asia Taiheiyo sekitan kaihatsu kodoka chosa. Chugoku ni okeru model tanko no seisan keikaku no sakutei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In view of the prospective demand for coal in China and of the current state of transportation, a development plan is formulated for Tangkou Mining Area (of model mines) for the purpose of realizing efficient exploitation of coal. The infrastructures for coal transportation are complete in this area, and delivery of coal is easy from this area to the coal demanding regions. Although coal seams are quite deep in the ground, the important ones contain rich reserves. Exploitation is carried out under a vertical shaft scheme, in which pits extend horizontally at the level of 950m below the sea surface. As for production, an annual yield of 3-million ton is predicted thanks to two compositely mechanized coal faces. Coal is won by the monolayer side hole method in the case of seams not thicker than 4.0m, and by the caved stope method in the case not thinner than 4.0m. Employed for the mines are 1077 people. Operation days are 300, efficiency 15t/man/shift. The annual sale in total is expected to be worth 759-million 534.6-thousand yuan. To be required for the construction will be 1.2-billion yuan for mines and 0.2-billion yuan for coal dressing facilities, or 1.4-billion yuan in all, and the figures indicate that the plan is economically promising. 43 figs., 119 tabs.

  12. Fiscal 2000 information collection/analysis project on basic research for coal resource exploitation. Research on technology of low-concentration methane gas recovery from underground coal mine; 2000 nendo sekitan shigen kaihatsu kiso chosa joho shushu kaiseki jigyo. Konaikutsu tanko ni okeru teinodo methane kaishu gijutsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Technical trends were surveyed concerning the recovery and the use as fuel of low-concentration methane gas or the like contained in the air ventilated out of coal mines. Methane gas recovery technologies include high-temperature incinerators and catalytic incinerators designed to collect heat, method of conversion of methane to CO2 using microbes named methanotrophs, and adsorption methods using activated charcoal, zeolite, or the like. Among technologies that have reached a practical level in the utilization of mine methane gas, there are the temperature regenerative flow-reversal reactor (TFRR) and the catalytic flow-reversal reactor (CFRR) utilizing high-temperature oxidation reaction. TFRR has been reported effective by MEGTEC System after a 6-month operational test of a 3.0m{sup 3}/s plant at a British coal mine. Test and research are over with CFRR, which is now ready for a commercial scale verification test. Recovery by adsorption, though worth further research efforts, is economically away from commercialization at the present stage, and wants more studies of adsorbents, etc. (NEDO)

  13. Survey report for fiscal 1998. Survey of the current state and tasks of research and development of technologies for effectively utilizing CO{sub 2} fixation by higher vegetation; 1998 nendo chosa hokokusho. Koto shokubutsu ni okeru nisanka tanso koteika yuko riyo gijutsu no kenkyu kaihatsu no genjo to kadai ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Investigations and studies are conducted seeking for a CO2 fixation method improved by utilizing the photosynthesizing function of higher vegetation. Details of higher vegetation genes are being disclosed thanks to the rapid progress of studies making use of molecular biological techniques, and the application of the genetic mechanism to scientific and technological fields is becoming increasingly feasible. In particular, the role of the CO2 fixation enzyme RuBisCO has been elucidated almost completely. It has been learned that, in terms of photosynthesizing capability, the C{sub 4} plants (corn etc.) are 2-3 times higher than the C{sub 3} plants (rice, wheat, etc.), and 5-10 times higher than the CAM plants (cactuses etc.). Studies are also under way about the rice genome so that a photosynthesizing capability so high as that of the C{sub 4} plants may be endowed the rice plant. The metabolism and control of useful substances produced in the CO2 fixation process etc. in the higher vegetation are being investigated, and it is now expected that some day such useful substances will be produced and utilized efficiently. Researches are under way into the relationship between the green leaf that is the organ that performs photosynthesis and the organ (sink) that stores and utilizes starch and sugar is in progress, and now a new field is going to open where vegetables will be fully utilized. (NEDO)

  14. Study on the large-scale photovoltaic (PV) power generation in desert of China and its utilization. Development of energy and agriculture in solar farm; Chugoku ni okeru ogata taiyoko hatsuden to sono riyo ni kansuru kenkyu. Solar farm ni yoru energy to nogyo kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nishioka, S.; Ohashi, Y.; Ito, H. [Tokyu Construction Co. Ltd., Tokyo (Japan); Ojima, S. [Maeda Corp., Tokyo (Japan)

    1997-01-30

    This paper proposes solar farm, a system suitable for China`s present circumstances, and describes its development plan. In this plan, agriculture and stock farming are promoted through irrigation using PV power in the desert zone, middle-east China. In addition, electric power is produced by laying PV power generation modules. The solar farm has 100 blocks of farmland equivalent to 700 ha, which includes 300 farmhouses (population of 1200). It can be a food supply base producing rice and wheat. The power generation capacity is at least 1000 kW, and the night power is supplied by battery installed in each farmhouse. The power generated in the daytime is used not only for agriculture but also for secondary industry such as processing of agricultural and stock farming products. The Chinese government requires 300,000 ha of farmland development every year up to 2030, the peak of population. When a half of this is developed by the solar farm, 200 solar farms are to be developed every year. For 30 years, 6000 solar farms are to be developed. 5 refs., 1 fig., 1 tab.

  15. Report on a project to support promotion of forming an environmentally friendly energy community. Survey on business feasibility of electric power generation utilizing combustible wastes solidified fuel in the Kishu and Kumano living area; Kankyo chowagata energy community keisei sokushin hojo jigyo chosa hokokusho. Kishu Kumano seikatsuken'iki ni okeru kanensei haikibutsu kokeika nenryo riyo hatsuden jigyo no jigyoka kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys and discussions were given on business feasibility of a wide area RDF power generation system in the Kishu and Kumano living area. The discussions dealt with as wide area as transcending prefectural borders and including the southern parts of Mie and Nara Prefectures with the city of Shingu as the central part. Wastes generation amount is estimated to be about 70,000 tons at the present as wastes that can be turned into RDF, and to be decreased to 67,000 tons in 2018. The manufactured RDF has calorific power of 3500 to 4500 kcal/kg, two to three times greater than that of wastes. The RDF manufacturing facilities installed in cities, towns and villages have capacity of 30 to 50 tons a day, with that in the city of Shingu being the largest at about 78 tons a day. Transportation can be implemented most efficiently when road transportation is used. The RDF power generation system will consist of a fluid bed furnace, a plasma type ash melting furnace, and a bag filter plus activated carbon absorbing tower. The RDF manufacturing cost will be 27,900 yen per ton of wastes in the case of the city of Shingu. In terms of business profitability, the RDF power generation must find sources to pay 21,400 yen per ton of RDF even if the power sale revenue is considered. (NEDO)

  16. Geothermal energy development activities. Report of the field trip of the Development and Utilization of Geothermal Resources in Tianjin, the 30th International Geothermal Congress; Dai 30 kai IGC chugoku tenshinshi ni okeru chinetsu chokusetsu riyo no kengaku ni sanka shite

    Energy Technology Data Exchange (ETDEWEB)

    Matsubayashi, O. [Geological Survey of Japan Ibaragi (Japan)

    1997-06-01

    The 30th International Geothermal Congress (IGC) was held in August, 1996, in the Beijing Great Hall of People`s Congress, Beijing, China. The author of the paper took part in an excursion being a part of IGC titled the Development and Utilization of Geothermal Resources in Tianjin and reported the summary in this paper. Because the Tianjin area has relatively high geothermal gradient, the direct utilization of the geothermal resources has been pushed forward from the 1980`s. An electron controlled hot water production and supply system developed by the Geothermal Resources Center, Tianjin Environment Protection Bureau is characterized in not utilizing any heat exchanger and conducting chemical treatments to prevent scaling. This system adopts a fuzzy-control, calculates the most suitable operating condition based on 48 kinds of observed parameters (hot water flow rate, pressure, external temperature, etc.) and controls automatically all the hot water production and supply system. The system can supply warming for 95,000 square meters including a municipal library and the neighboring 6 buildings. 6 refs., 4 figs., 1 tab.

  17. Development of hydroponic system using agriculture waste. 1. Characteristics of rice husk charcoal as growth medium and vegetable growth; Suiko saibai ni okeru haikibutsu riyo gijutsu no kaihatsu. 1. Momigara kutan no baichi to shite no tokucho to yasai no seiiku

    Energy Technology Data Exchange (ETDEWEB)

    Terazoe, H.; Nakaya, K.; Okano, T. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1994-06-01

    Experimental researches were made on rice husk charcoals processed to be used as culture media for hydroponics. Rice husk charcoals with a size of 1 mm or larger retaining the original shape of the rice husk, and with a size of smaller than 1 mm were made for use in the experiment. In the culture media made of these rice husk charcoals, the charcoal with a particle size greater than 1 mm had more air portion than water portion at 6 cm above the water level, and the charcoal with a particle size smaller than 1 mm had poor air permeability. According to the result of immersing the rice husk charcoal in a culture solution, phosphoric acid ion and manganese in the solution decreased by about 35% and calcium by about 10% in the duration of 120 minutes, as a result of having been adsorbed into the rice husk charcoal. On the other hand, chloride ion increased by about 80% and potassium and iron by about 30%, because of having been dissolved out from the charcoal. In cultivating spinach, butterhead lettuce and radish in the rice husk charcoal culture media, the culture medium with charcoal smaller than 1 mm resulted in harvest reduced by about 75% in spinach, and about 10% in butterhead lettuce. 15 refs., 13 figs., 11 tabs.

  18. Study on the large-scale photovoltaic (PV) power generation in desert of China and its utilization. Development of energy and agriculture in solar farm; Chugoku ni okeru ogata taiyoko hatsuden to sono riyo ni kansuru kenkyu. Solar farm ni yoru energy to nogyo kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nishioka, S.; Ohashi, Y.; Ito, H. [Tokyu Construction Co. Ltd., Tokyo (Japan); Ojima, S. [Maeda Corp., Tokyo (Japan)

    1997-01-30

    This paper proposes solar farm, a system suitable for China`s present circumstances, and describes its development plan. In this plan, agriculture and stock farming are promoted through irrigation using PV power in the desert zone, middle-east China. In addition, electric power is produced by laying PV power generation modules. The solar farm has 100 blocks of farmland equivalent to 700 ha, which includes 300 farmhouses (population of 1200). It can be a food supply base producing rice and wheat. The power generation capacity is at least 1000 kW, and the night power is supplied by battery installed in each farmhouse. The power generated in the daytime is used not only for agriculture but also for secondary industry such as processing of agricultural and stock farming products. The Chinese government requires 300,000 ha of farmland development every year up to 2030, the peak of population. When a half of this is developed by the solar farm, 200 solar farms are to be developed every year. For 30 years, 6000 solar farms are to be developed. 5 refs., 1 fig., 1 tab.

  19. Bioprocessing of coal. 1. Sekitan no seibutsu kako. 1. ; Sekitan wo datsuryusuru biseibutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, K.; Omura, N.; Saiki, H.; Kono, Y.

    1989-11-01

    In the bioprocessing of coal using biotechnology, desulfurizing microorgaisms were examined. 30-70% of total sulfur in coal is occupied by inorganic sulfur, almost of that is a form of FeS {sub 2}. Using some acidophilic sulfur oxidizing bacteria such as Thiobacillus ferrooxidans and Thermophilic-acidophilic bacterial such as Sulfolobus acidocaldarius, about 90% of inorganic sulfur in coal can be removed in 1 or 2 weeks in pulverized coal-water slurry, a high possibility in practical use is shown. Organic sulfur (total sulfur {minus} inorganic sulfur) is difficult to be removed, since it is combined with carbon in a from of covalent bond. Sulfolobus acidocaldarius can remove both inorganic and organic sulfur simultaneously. One mutant strain of Pseudomonas is excellent at the rate of desulfurization. These organisms must be superior to others, but their desulfurization ratios are generally low. Some bacteria can degrade some kinds of low-rank coals into water soluble liquid fuel, and the ash content is decreased. Bioconversion of low-rank coals to methane gas applying methane enzyme principle, has been proposed, however, still an idea. 81 refs., 5 figs., 15 tabs.

  20. Estimation for origin of coals on biomaker analysis; Jinko sekitan oyobi tennen sekitan no biomaker bunseki ni yoru sekitan kigen busshitsu no suitei

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Y. [Geological Survey of Japan, Tsukuba (Japan); Sugimoto, Y. [National Institute of Materials and Chemical Research, Tsukuba (Japan); Okada, K. [Coal Mining Research Center, Tokyo (Japan)

    1996-10-28

    In order to study coal production processes, an estimation study was carried out on coal originating materials by using biomaker analysis. Test samples are original coals collected directly from a mine in Hokkaido (not having been subjected cleaning). Mixing and solvent extraction were performed after pulverization, and then tests were given on saturated hydrocarbon components divided by using a silicagel column chromatograph for the present study. It can be known from n-alkane distribution in the coal that low molecular alkane increases with increasing degree of coalification. Artificial coal made by wet-heating Metasequoia leaves contains only little n-alkane. Diterpenoid compound exists in the Taiheiyo and Akabira coals. Tetra-cyclic diterpernoid is contained abundantly in subtropical coniferous trees, serving as a parameter for warm environment. The compound is contained also in the Fushun coal, but not in Indonesian coals. Hopanoid constitution shows very high similarity, but H/C atomic ratio may vary largely even if the coalification is at the same degree. This is likely to be caused from difference in originating materials. Hopanoids are bacteria attributed substances, whose activities are not affected by the originating materials. 2 figs., 1 tab.

  1. Energy conversion with application of biotechnology. Baio riyo energy henkan

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, T.; Uozumi, N. (Nagoya Univ., Nagoya (Japan). Faculty of Engineering)

    1992-09-05

    Biological resources are produced by photosynthetic action of plants by the use of solar energy and decomposed and circulated mainly by microorganisms in the ecological system. Various energy conversions are possible by the use of functions of microorganisms. The paper overviews the various energy conversion systems under investigation. A bioreactor to produce hydrogen by the use of a certain microorganism from organic compounds in a dark condition is studied in combination with oxygen and nitrogen removal system. Anaerobic methane fermentation has been used practically and the process is noteworthy to use marine biomass as the raw materials. Eucalyptus, Ricinus (castor oil plant) and Hevea (para rubber plant) attract attention on direct production of hydrocarbons. While alcoholic fermentation is known since ancient times, ethanol is now used in automobile fuel, and cellulose is a subject of a study as a raw material of fermentation instead of starch. The investigation includes effective utilization techniques of cellulose by degradation and higher efficiency of photosynthesis by use of technologies of genetic engineering. 1 ref., 2 figs.

  2. Agglomeration and reaction characteristics of various coal chars in fluidized-bed coal gasifier; Ryudoso sekitan gas ka ronai deno sekitan no gyoshu tokusei to hanno tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Uemiya, S.; Aoki, K.; Mori, S.; Kojima, T. [Seikei University, Tokyo (Japan). Faculty of Engineering

    1996-10-28

    With relation to the coals delivered as common samples in the coal fundamental technology development project, an experimental study was conducted on agglomeration characteristics and reaction characteristics in the fluidized-bed coal gasifier. For the experiment, used was a fluidized bed gasifier inserted with a cone-shape dispersion plate with a nozzle in the center. After raising the temperature of the gasifier up to 773K, gasification was conducted sending to the gasifier air from the nozzle and steam from the dispersion plate. The mean particle diameter and gas concentration of chars were measured till the temperature reaches 1373K. As a result of the experiment, it was confirmed that the carbon conversion ratio increases with a decrease in coalification degree of the coal. Moreover, influence of the coal kind was markedly observed at the grid zone of the lower part of the bed, and it was clarified that the lower carbon content ratio the coal kind has, the faster the speed of CO formation and water gasification get. The agglomeration temperature of charcoal which is a product of the condensate is lower by as many as several hundred K than the point of softening, and it was considered to be necessary to study the relation with the temperature distribution in the bed. 3 refs., 3 figs., 1 tab.

  3. Sorption phenomena of methanol on heat treated coal; Netsushori wo hodokoshita sekitan no methanol kyuchaku tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Yasuda, H.; Kaiho, M.; Yamada, O.; Soneda, Y.; Kobayashi, M.; Makino, M. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    Experiments were carried out to learn methanol sorption characteristics of heat-treated coal. When Taiheiyo coal is heat-treated at 125{degree}C, performed with a first methanol adsorption at 25{degree}C, and then desorption at 25{degree}C, a site with strong interaction with methanol and a site with relatively weak interaction are generated in test samples. A small amount of methanol remains in both sites. Then, when the methanol is desorbed at as low temperature as 70{degree}C, the methanol in the site with strong interaction remains as it has existed therein, but the methanol in the site with relatively weak interaction desorbs partially, hence the adsorption amount in a second adsorption at 25{degree}C increases. However, when desorption is performed at as high temperature as 125{degree}C, the methanol in the site with strong interaction also desorbs, resulting in increased adsorption heat in the second adsorption. The adsorption velocity drops, however. Existence of methanol in a site with strong interaction affects the adsorption velocity, but no effect is given by methanol in a site with weak interaction. 3 refs., 4 figs.

  4. Characteristics estimation of coal liquefaction residue; Sekitan ekika zansa seijo no suisan ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Itonaga, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Okada, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

    1996-10-28

    The paper studied a possibility of estimating characteristics of coal liquefaction residue from liquefaction conditions in the case of fixing coal kind in the NEDOL process coal liquefaction PSU. Wyoming coal was used for the study, and the already proposed simplified liquefaction reaction models were used. Among material balances explained by the models, those of asphaltene, preasphaltene, THF insoluble matters are concerned with residue composition. Ash content is separately calculated from ash balance. Reaction velocity constants of simplified liquefaction reaction models which influence the residue composition were obtained by the multiple regression method from experimental results in the past. The estimation expression of residue viscosity was introduced from residue ash/composition. When the residue composition is estimated by the model from liquefaction conditions, and the residue viscosity is obtained using it, the higher the liquefaction temperature is, the higher the residue viscosity is. The result obtained well agreed the measuring result. The simplified liquefaction model of a certain coal kind has been established, and characteristics of residue can be estimated even at liquefaction conditions which have never been experienced before if there is a certain amount of the accumulated data on residue composition/characteristics. 4 refs., 4 figs., 4 tabs.

  5. Viscosity change of coal during carbonization; Sekitan tanka hannochu no nendo henka

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, K.; Hayashi, J.; Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    In relation to softening, melting and solidification of coal during heating, the effect of heating rate and nitrogen gas pressure on viscosity change, and change with time in the yield of pyridine extract were measured to study the mechanism of viscosity change. In experiment, six kinds of coals were used, and their needle penetration and dilatation were measured using compacted disk coal pellets. The coking and slight coking coal heat-treated under the same condition as the above experiment were used for pyridine extraction. As the experimental result, the apparent viscosity during coal heating was dependent on heating rate, nitrogen pressure and coal kinds. The minimum apparent viscosity decreased with an increase in heating rate and nitrogen pressure, and approached to a constant value. Like apparent viscosity change, the yield of pyridine extract was also dependent on heating rate, and its temperature range nearly agreed with that of apparent viscosity change. It was suggested that the viscosity is dependent on not only the mass fraction of plastic intermediate but also temperature and the relation between plastic intermediate and other components. 3 refs., 5 figs., 1 tab.

  6. Sorption mechanism of solvent vapors to coals; Sekitan eno yobai joki no shuchaku kiko no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, K.; Takanohashi, T.; Iino, M. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

    1996-10-28

    With an objective to clarify the interactions between micropore structure of coal and solvent reagents, a sorption experiment was carried out under solvent saturated vapor pressure. Low-volatile bituminous coal, Pocahontas No. 3 coal, has the aromatic ring structure developed, and makes solvent more difficult to diffuse into coal, hence sorption amount is small. Methanol has permeated since its polarity is high. High-volatile bituminous coal, Illinois No. 6 coal, makes solvent penetrate easily, and the sorption amount was large with both of aromatic and polar solvents. Since brown coal, Beulah Zap coal, contains a large amount of oxygen, and hydrogen bonding is predominant, sorption amount of cyclohexane and benzene having no polarity is small. Methanol diffuses while releasing hydrogen bond due to its polarity, and its sorption amount is large. A double sorption model is available, which expresses the whole sorption amount as a sum of physical sorption amount and amount of permeation into coal. This model was applied when it explained successfully the sorption behavior of the solvents relative to coals, excepting some of the systems. However, also observed were such abnormal behavior as sorption impediment due to interactions between coal surface and solvents, and permeation impediment due to hydroxyl groups inside the coals. 1 ref., 10 figs., 2 tabs.

  7. Depolymerization of coal by oxidation and alkylation; Sanka bunkai to alkyl ka ni yoru sekitan kaijugo

    Energy Technology Data Exchange (ETDEWEB)

    Tomita, H.; Isoda, T.; Kusakabe, K.; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hayashi, J. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    Change in depolymerization degree and coal structure was studied for depolymerization treatment of coal in various alcohol containing aqueous hydrogen peroxide. In experiment, the mixture of Yallourn coal, alcohol and aqueous hydrogen peroxide was agitated in nitrogen atmosphere of normal pressure at 70{degree}C for 12 hours. As the experimental result, the methanol solubility of only 5% of raw coal increased up to 35.2% by hydrogen peroxide treatment, while the yield of insoluble matters also decreased from 94% to 62%. Most of the gas produced during treatment was composed of inorganic gases such as CO and CO2, and its carbon loss was extremely decreased by adding alcohol. From the analytical result of carbon loss in hydrogen peroxide treatment, it was clarified that alkylation advances with introduction of alkyl group derived from alcohol into coal by hydrogen peroxide treatment under a coexistence of alcohol, and depolymerization reaction of coal itself is thus promoted by alcohol. 4 refs., 7 figs., 1 tab.

  8. Change in pore structure of coals by activation with KOH; KOH fukatsushita sekitan no saiko kozo

    Energy Technology Data Exchange (ETDEWEB)

    Maruyama, K.; Yoshizawa, N.; Ishikawa, E.; Kobayashi, M.; Toda, Y.; Yamada, Y.; Shiraishi, M. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    Three typical Japanese coals of non-coking coal, coking coal and anthracite were heat-treated with KOH, and change in their pore structure was examined by absorption of N2, X-ray diffraction and TEM observation. In addition, the relation between a coal rank and pore structure was also studied by absorption experiment of N2. In experiment, the mixture of coal and KOH in a nickel holder was heat-treated in N2 gas flow at heating rate of 2{degree}C/min, and held at a fixed temperature for one hour. To clarify the pore structure, N2 absorption isotherms were measured at -196{degree}C under nearly 76cmHg using a commercially available full-automatic absorption measurement equipment. Based on the X-ray diffraction and TEM observation results on activated coals, the relation between the N2 absorption and pore structure was studied. The results are summarized as follows: (1) The yield and absorption ability of coals increase with a coal rank, (2) The specific surface area of coals reaches its peak at 800{degree}C in activation temperature regardless of a coal rank, and (3) The activation behavior of coals is dependent on a coal rank. 5 refs., 7 figs., 1 tab.

  9. Coal technologies of Japan in 1988 and 1989. 1988, 1989 nen no sekitan gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    1990-09-25

    The 8th coal policy of Japan which has been in effect since 1987 has passed its half way and during the above period, coal mines such as Mitsubishi Takashima, Mitsui Sunagawa, Hokutan Horonai and Mitsubishi Minami-Ohyubari, etc. were closed and further concentration and rationalization of the production systems has been continued. Total coal production in FY 1988 as well as FY 1989 was 11.1 million tons and 9.7 million tons respectively, and concerning the development surveys of coal resources, maritime geophysical explorations and test drillings were done in Ariake Sea and off Kushiro, etc. and land geophysical explorations and test drillings at Asajino, etc.. International interchange concerning coal technologies was also very active and the amount of imported coal of various kinds exceeded that of the preceding fiscal year in both fiscal years, irrespective of the unconsumed year-end surplus coal storage in the domestic coal production. As shown above, domestic coal is inferior to overseas coal pricewise, hence domestic coal mines are pushing concentration of faces and introduction of larger coal mining machines. With regard to coal mine safety, the research and development of technologies of prediction and safety against gas issue, spontaneous combustion and mine fire, etc. is under way and coal processing technologies as well as coal utilization technologies such as fluidized bed incineration, etc. are now being developed. 3 figs., 12 tabs.

  10. Development of pressurized coal partial combustor; Kaatsu sekitan bubun nenshoro gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T. [Center for Coal Utilization, Japan, Tokyo (Japan); Kawamura, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Tanaka, T. [Chubu Electric Power Co. Inc., Nagoya (Japan); Muramatsu, T. [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    The coal partial combustor (CPC) uses a combustion technology with which coal is burned at elevated temperatures and under revolution, the constituents are captured on the furnace wall and removed as molten slag from the furnace. This is a combustion technology to reduce load of ash on subsequent devices. To generate a molten condition, it is necessary to raise the combustion temperature as high as possible (to about 1600 degC in the furnace), but this is effective for a gas turbine composite power generation system. An efficiency of higher than 45% may be expected at the power transmission terminal. As an operation on subsidy from the Agency of Natural Resources and Energy, the normal-pressure CPC technology has already been established, and a research on pressurized CPC is being progressed since fiscal 1991. The research is in progress with a schedule that elemental tests for 7 tons per day production are conducted until fiscal 1995, a 25 tons per day pilot plant will be completed by November 1997, and verification tests for long-term continuous operation will be implemented until 1998. The 7 tons per day elemental tests have identified gasification performance and slag extraction performance using five types of coal having different properties. 7 refs., 10 figs., 4 tabs.

  11. Development of advanced coal cleaning process; Kodo sekitan kaishitsu gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Osaka, S. [Center for Coal Utilization, Japan, Tokyo (Japan); Akimoto, A.; Yamashita, T. [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

    1996-09-01

    This paper aims to develop a clean coal production process which excellently removes environmental pollutant, is low-costed, and need no particular systems for distribution of products. The result of the development was described paying attention to column flotation which is a technology to high-efficiently select particulate regions, particulate heavy media cyclone, magnetic separation, and the basic design of the process into which those above were integrated. The two-stage selection process, which is an integration of column flotation and particulate heavy media cyclone into the conventional coal preparation equipment, can produce low-ash clean coal at high separation efficiency and also suppress the rise in processing cost. This process was also effective for removal of sulfur content and trace metal elements. The use of clean coal at power plant can be effective for not only the reduction in ash treatment amount, but the aspect of boiler operation characteristics such as heat transfer efficiency of boiler furnace wall, ash related troubles, loads of electrostatic precipitator, loads of flue gas desulfurization facilities. 17 figs., 5 tabs.

  12. nihon no iryo jujisha ni okeru shokugyosei sutoresu

    OpenAIRE

    伊藤, 慎也

    2014-01-01

    主査 : 水野雅文 /タイトル : Occupational stress among healthcare workers in Japan /著者 : Shinya Ito, Shigeru Fujita, Kanako Seto, Takefumi Kitazawa, Kunichika Matsumoto, Tomonori Hasegawa /掲載誌 : Work: A Journal of Prevention, Assessment and Rehabilitation /巻号・発行年等 : 49(2):225-234, 2014 /本文ファイル : 出版者版

  13. Bonded structure application for aircraft. Kokuki ni okeru secchaku gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, O. (Japan Airlines Co. Ltd., Tokyo (Japan))

    1991-01-05

    Adhesives play an important role in a technology of the aircraft structure for which lightness and strength are required. The paper explains the present situation of bonding technology employed for aircraft, the honeycomb structure, production of composite materials and the related problems. Advantages and purposes of employing adhesives as substitutes for fasteners like screws, rivets, etc. are as follows: decreases in stress concentration, weight reduction, smoothing of surfaces, improvement of acoustic fatigue by adhesives flexibility, prevention of gas-liquid leakage. Epoxide adhesives are mainly used for aircraft. Together with tear straps, which are metal-metal bonded to the rear fuselage plate of aircraft, and waffle doublers, an aluminium honeycomb sandwich structure, whose weight is 1/7 of an aluminium plate same in rigidity, is used in such parts of aircraft as spoilers, outer plates of flaps, etc. The problem of the bonded structure is detachment. Therefore, how to prevent, discover and repair it is most important. 3 figs.

  14. Idea of environmental catalyst and its application; Kankyo shokubai no hasso to sono riyo

    Energy Technology Data Exchange (ETDEWEB)

    Inumaru, K. [The University of Tokyo, Tokyo (Japan)

    1997-10-20

    The catalyst creating environmental conservation and comfortable environment is generally named an `environmental catalyst (EC).` EC is roughly classified into direct and indirect type ECs. Purification catalysts for automobile exhaust gas, and catalysts for chemical production process are under investigation as direct and indirect type ECs, respectively. The catalyst was found which can remove NOx under the coexistence of oxygen by using hydrocarbon as reductant. In addition, the practical exhaust gas purification catalyst was also developed for lean-burn engines by combining noble metal catalysts with NOx absorbing materials or zeolite superior in reductant adsorbing power. {epsilon}-caprolactam as raw material of nylon 6 is synthesized from cyclohexanoneoxime through Beckmann` rearrangement reaction. Zeolite system solid catalysts using no ammonia are under investigation. An environment-friendly synthesis method using not phosgene but catalyst was proposed for production of dimethyl carbonate. How to utilize catalysts for global material circulation remains unsolved for the future study. 5 refs.

  15. Biotechnological application of marine microalgae; Kaiyo sorui no biotechnology eno riyo

    Energy Technology Data Exchange (ETDEWEB)

    Matsunaga, T.; Takeyama, H. [Tokyo University of Agriculture and Technology, Tokyo (Japan). Faculty of Technology

    1995-09-10

    There are many kinds of micro algae who have adapted to extremely diversified marine environments. Screening of new useful materials from marine micro algae has been carried out. High density culture system using photo-bioreactor and genetic manipulation technology have been employed in order to enhance productivity of those materials from marine micro algae. We have found many useful materials, such as UV-A absorbing substance, plant growth regulating factor, polysaccharides, unsaturated fatty acids and antibiotics, from marine micro algae. Here, we describe production of those useful materials and their application. Marine coccolithophorid algae convert CO2 to CaCO3 and they have been expected to contribute to CO2 recycling system. Metabolic engineering in marine microalgae, especially cyanobacteria, has been established. Eicosapentaenoic acid is successfully synthesized in marine cyanobacterium which can not synthesize it. 41 refs., 14 figs., 5 tabs.

  16. Generic supercritical water technology; Generic technology to shite no chorinkaisui riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Arai, K.; Ajiri, M.; Inomata, H.; Smith, R.; Hakuta, Y. [Tohoku University, Sendai (Japan). Faculty of Engineering; Yokoyama, C. [Tohoku University, Sendai (Japan). The Institute forChemical Reaction Science; Chin, L. [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-02-01

    This paper describes the measurement and analysis for clarifying solution structure of supercritical water and exhibition mechanism of solvent functions. It also describes the development of new processes using supercritical water as reaction solvent. The PVT measurements were conducted in the supercritical region using pure water and NaCl aqueous solution, to confirm the reduction of molar volume of the electrolyte solution. The hydration structure was examined in the supercritical aqueous solution by the molecular dynamic simulation. As a result, presence of hydrogen bond structure, where the contribution of two branching hydrogen bond can not be ignored, was suggested under the supercritical condition. Characteristics of supercritical aqueous solutions are analyzed through in-situ Raman and scattered X-ray spectral measurements. Moreover, this paper introduces developments of some processes in the supercritical water, such as decomposition of wasted polymers, recovery of chemical materials, reforming of heavy hydrocarbons by contact hydrogenation, and synthesis of fine powders of metal oxide by reaction crystallization.

  17. Performance test of solar energy distillation system; Taiyonetsu riyo kaisui tansuika system no zosui seino shiken

    Energy Technology Data Exchange (ETDEWEB)

    Kawahara, T.; Toyoshima, Y. [Keio University, Tokyo (Japan); Narasaki, Y.; Kamiya, I. [Ebara Corp., Tokyo (Japan); Sato, H. [Keio University, Tokyo (Japan). Faculty of Science and Technology

    1997-11-25

    In order to develop a seawater desalination equipment utilizing solar heat, a performance test was performed on a three-stage solar heat vacuum distiller. The equipment can evaporate and condense water at low temperatures by reducing the pressure in a distilling section. Solar heat is collected by a heat collecting plate, by which water as the working fluid is evaporated and moved to a heat conducting section in an evaporation pipe in a state of steam. The steam is condensed in a low-temperature heat conducting pipe, the heat is released outside the heat conducting pipe, and seawater is evaporated under low pressure condition. The working fluid is circulated for repetitive use. Solar cells are used as a motive power source for a vacuum pump, hence the system is self-sustainable even if installed in a desert area and the like places. The construction is simple, highly durable, and easy in maintenance. The system has high water producing performance, uses no harmful substances whatsoever such as fluorocarbons, and is a friendly system to the global environment. Because of evaporation at low temperatures, heat loss to the surroundings and sensible heat due to temperature rise are small, and the system response is quick. The solar heat can be utilized more effectively as multiple effects. When a heat collecting plate of 7.76 m {sup 2} was used, maximum yield of 105.45 kg/day was obtained. The system`s distillation efficiency is higher than other types of solar heat utilizing distillers. 7 refs., 5 figs.

  18. Coal demineralization with Ca(OH)2. Hydrothermal reaction between Ca(OH)2 and quartz; Ca(OH)2 wo mochiita sekitan no kagakuteki dakkai. Ca(OH)2 to sekitan no suinetsu hanno

    Energy Technology Data Exchange (ETDEWEB)

    Wang, J.; Tomita, A. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

    1996-10-28

    Coal demineralization mechanism and its optimum condition were studied by hydrothermal reaction between Ca(OH)2 and quartz as a coal demineralization model. In experiment, the mixture of powder quartz and Ca(OH)2 water slurry was subjected to reaction in an autoclave under spontaneous pressure at 175-340{degree}C. After dried in N2 gas atmosphere at 105{degree}C, the reaction product was analyzed by X-ray diffraction, thermo-balance and differential thermal analysis. In measurement of quartz conversion, the specimen was analyzed by X-ray diffraction after removal of bound water by heat treatment at 850{degree}C. The mixture of clean coal deashed by NaOH and a fixed amount of quartz was also used as specimen for experiment. As the experimental result, dicalcium silicate hydrate was mainly produced at 175{degree}C, and the product changed into xonotlite through tobermorite by longer treatment at higher temperature. For complete reaction of quartz, heat treatments for 7 and 5 hours at 300 and 400{degree}C were necessary, respectively. 2 refs., 2 figs., 2 tabs.

  19. Behavior of catalyst and mineral matter in coal liquefaction; Sekitan ekika hannochu no kobusshitsu to shokubai no kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Iwasaki, K.; Wang, J.; Tomita, A. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

    1996-10-28

    Mineral matter in coals is important in various senses for coal liquefaction. It is possible that the catalytic activity is affected by the interaction between catalyst and mineral matter. Iron-based catalyst forms pyrrhotite in the process of liquefaction, but the interaction between it and mineral matter is not known in detail. In this study, the interaction between mineral matter and catalyst and the selective reaction between them were investigated. Tanito Harum coal was used for this study. This coal contains a slight amount of siderite and jarosite besides pyrite as iron compounds. Liquefaction samples were obtained from the 1 t/d NEDOL process PSU. The solid deposits in the reactor mainly contained pyrrhotite and quartz. A slight amount of kaolinite was observed, and pyrite was little remained. It was found that the catalyst (pyrrhotite) often coexisted with quartz, clay and calcite. 8 figs., 2 tabs.

  20. Surface tension of a coal extract in an organic solvent; Sekitan chushutsu seibun no kaigo to hyomen choryoku

    Energy Technology Data Exchange (ETDEWEB)

    Kikuchi, T.; Hayasaka, K.; Takanohashi, T.; Iino, M. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

    1996-10-28

    The behavior and properties of associated bodies were studied through measurement of surface tension considering acetone-soluble fraction relatively light among various solvent extracts of coal. In experiment, the acetone-soluble fraction was extracted from the substances extracted from Upper Freeport coal as standard specimen using the mixed solvent of carbon disulfide (CS2) and N-methyl-2-pyrrolidinone (NMP), and it was dissolved into NMP after drying. Surface tension was measured by Wilhelmy method. The experimental results are as follows. Equilibrium surface tension is equal to the surface tension of pure solvent in a low concentration range of solution, and decreases with an increase in concentration approaching a fixed value at 0 in log concentration, nearly showing an S curve. Adsorption of species with non-polar aromatic ring of the acetone-soluble fraction on a solution surface probably decreases surface tension. Change with time in surface tension is observed which suggests fast initial reaction and slow subsequent reaction. 4 figs.

  1. Coal Liquefaction characteristics and chemical structure of product oil; Sekitan ekika hanno tokusei to seiseibutsu no kagaku kozo

    Energy Technology Data Exchange (ETDEWEB)

    Endo, H.; Sato, M.; Chiba, T.; Hattori, H. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology; Sasaki, M. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-10-28

    Through the hydrogenolysis of Wandoan coal and Tanito Harum coal which are used for the NEDOL process, differences of liquefaction characteristics between them were found. The purpose of this study is to grasp these differences as differences of chemical structures of oil fractions. The compound type analysis was conducted for oil fractions obtained at varied reaction temperature for varied reaction time. Coal liquefaction characteristics of these coals were discussed by relating oil yields and chemical structures. For Tanito Harum coal, yields of gas and oil were considered to be lower than those for Wandoan coal, which reflected that the contents of partially hydrogenated hydroaromatics in oil fraction from the former were lower than those from the latter, and that the remarkable change of composition did not occur with the progress of the reaction. For both the coals, the remarkable changes in the average molecular weight of oil fraction were not observed with the progress of the reaction. While, the content of methane gradually increased with the progress of the reaction, which suggested that oil was gradually dealkylated. 5 figs.

  2. Studies on characteristics of fluid dynamics in the coal liquefaction reactor; Sekitan ekika hanno tonai no ryudo tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Sakawaki, K.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Tachikawa, N.; Moki, T.; Ishikawa, I. [Japan Atomic Energy Research Institute, Tokyo (Japan)

    1996-10-28

    To design the coal liquefaction reactor of large scale plant in future, it is important to understand characteristics of fluid dynamics within the coal liquefaction reactor. In this study, to measure the fluid dynamics of liquid phase within the coal liquefaction reactor operated under high temperature and high pressure coal liquefaction condition, neutron attenuating tracer (NAT) technique, one of the tracer test methods, was applied using 1 t/d coal treating PSU. The residence time of liquid phase within the reactor can be measured by utilizing property of neutron of being absorbed by materials. The tracer was injected at the inlets of first and third reactors, and the neutron was counted at each outlet. The concentration of tracer was derived from the discrete value, to determine the residence time distribution of liquid phase. The mean residence time of liquid phase in the single first reactor and in the total three reactors were prolonged under the severe operation conditions of liquefaction. The more severe the liquefaction operation condition was, the more active the mixing of liquid phase was in the first reactor. It was found that the progress of reaction was accelerated. 2 refs., 5 figs., 1 tab.

  3. Co-liquefaction of micro algae with coal. 2; Bisai sorui to sekitan no kyoekika hanno. 2

    Energy Technology Data Exchange (ETDEWEB)

    Ueda, C.; Matsui, T.; Otsuki, M.; Ikenaga, N.; Suzuki, T. [Kansai University, Osaka (Japan). Faculty of Engineering

    1996-10-28

    For the removal and recycle of CO2, a global warming gas, utilization of photosynthesis by micro algae is investigated. Formed micro algae are decomposed into CO2, H2O and CH4 again, which does not result in the permanent fixation. For the effective utilization of these micro algae, creation of petroleum alternate energy was tried through the co-liquefaction of micro algae with coal. Were investigated influences of the reaction temperature during the co-liquefaction and influences of catalysts, such as Fe(CO)5-S, Ru(CO)12, and Mo(CO)6-S, which are effective for the coal liquefaction. Micro algae, such as chlorella, spirulina, and littorale, and Yallourn brown coal were tested. It was found that co-liquefaction of micro algae with coal can be successfully proceeded under the same conditions as the liquefaction of coal. The oil yield obtained from the co-liquefaction in the presence of Fe(CO)5-S, an effective catalyst for coal liquefaction, agreed appropriately with the arithmetical mean value from separate liquefaction of coal and micro algae. It was suggested that pyrrhotite, an active species for coal liquefaction, was sufficiently formed by increasing the addition of sulfur. 2 refs., 7 figs., 1 tab.

  4. Computer Simulation Techniques for Molecular Structure of Coal for Advanced Coal Conversion Technology; Sekitan kodo henkan no tameno bunshikozo shimyureshon

    Energy Technology Data Exchange (ETDEWEB)

    Takanohashi, Toshimasa [Energy Resources Dept., Tokyo (Japan). Fundamental Research Div.; Nakamura, Kazuo [Osaka Gas Corp., Osaka (Japan). Fundamental Research Laboratories; Iino, Masashi [Tohoku University, Miyagi (Japan), Institute for Chemical Reaction Science

    1999-02-25

    Coal has complex chemical structure consisting of various bond types and the details are still not well understood. Recently, in addition to improvements of analytical techniques, molecular modeling and simulation techniques by using powerful computers and software have greatly developed and it has become possible to apply them to complex structure such as coal. Knowledge of coal's molecular structure is important for the understanding of various coal properties and reactivities under several conditions. In this paper, a new tool, i.e., molecular modeling technique of coal's macromolecular structure and dynamic simulation of coal properties, is introduced and the future applications of this technique will be outlined. (author)

  5. Development of coal gas production technology acceptable for fuel cells; Nenryo denchiyo sekitan gas seizo gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T. [Center for Coal Utilization, Japan, Tokyo (Japan); Kimura, N.; Omata, K. [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    In utilizing coal for high-efficiency direct power generation using fuel cells, it is necessary that coal be fed into the fuel cells after having been made into ash-free gaseous fuel. Research and development works are being carried out with an objective to develop a coal gasification furnace most suitable for fuel cells and establish a system to refine coal up to the one that can be fed into fuel cells. Fiscal 1995 has conducted investigations on coal gasification technologies, air separation technologies, and gas refining technologies as the important element technologies, and a trial design on integrated coal gasification fuel cell (IGFC) systems. This paper reports from among the above items the result of the trial design on an IGFC system using molten carbonate fuel cells. The paper describes system comparison on paths of produced gases and anode waste gas, comparison on refining processes using a wet system and a dry system, and parameter studies on oxygen concentration in gasifying agents. It was made clear that the suitable furnace is an oxygen blown coal gasification furnace, and the power generation efficiency at the system terminal can be higher than 53%. 11 figs., 6 tabs.

  6. Test and survey on a next generation coal liquefying catalyst. Coal molecule scientific test and survey as the base for commercializing the coal liquefying technology; Jisedai sekitan ekika shokubai shiken chosa. Sekitan ekika gijutsu shogyoka kiban to shite no sekitan bunshi kagaku shiken chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The test and survey on a next generation coal liquefying catalyst present a new proposal to raise catalytic activity in coal liquefaction, and perform demonstration experiments in a laboratory scale to search for possibility of developing a new coal liquefying catalyst from various viewpoints. To explain, discussions were given on the catalyst to perform the followings: liquefaction under extremely mild conditions by using ultra strong acids not limited only to metals; ion exchange method and swell carrying method to raise catalyst dispersion very highly, enhance the catalytic activity, and reduce the amount of catalyst to be used; mechanism of producing catalyst activating species to further enhance the activity of iron catalysts; and pursuit of morphological change in the activating species. The coal molecule scientific test and survey as the base for commercializing the coal liquefying technology performed the studies on the following items: pretreatment of coal that can realize reduction of coal liquefaction cost; configuration of the liquefaction reaction, liquefying catalysts, hydrocarbon gas generating mechanism, status of catalysts after liquefaction reaction, and reduction in gas purification cost by using gas separating membranes. Future possibilities were further searched through frank and constructive opinion exchanges among the committee members. (NEDO)

  7. Research and development of system to utilize photovoltaic energy. Survey on system and peripheral technologies for utilization of photovoltaic power; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on systems and peripheral technologies for use of PV power in fiscal 1994. On the case study of PV communities, as housing zone PV community, Seibu Kitanodai housing estate mainly composed of detached houses, and the Suwa area of Tama New Town of apartment houses were selected to study PV power generation on a roof, wall and window. The result clarified that generated energy of a detached house reaches 3-4 times as much as consumed one, that of an apartment house is nearly equal to consumed one, and power generation of nearly 380MW is possible based on expected housing supply until 2000. As urban core zone PV community, the survey result on Ebisu Garden Place clarified that the expected PV power supply rate is 10% or more, 20% and 30% or more for hotel and office buildings, high-rise apartment building more than 30 stories, and medium-rise one of 10 and several stories, respectively. In Sakura industrial estate, the maximum generated power was nearly equal to consumed power in a weekday, and as inverse power flow in a holiday was considered, the annual PV power supply rate was extremely high.

  8. Annual energy review-1996; 1996 nen ni okeru juyona energy kankei jiko

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-20

    This paper reviews the important items concerned with energy in 1996. Primary energy supply sums to 529times10{sup 13}kcal increasing by 2.4% over last year. The growth rates of demand over last year are 2.5% in industry use, 3.7% in transport use, 3.7% in home use, and 1.3% in business use. On R & D trend of use technologies of energy resources, the following are described: (1) Petroleum: resource exploitation, transport, stock, refining, and petrochemistry, (2) Coal: resource exploitation, coal structure and property, processing, transport, liquefaction, gasification, carbonization, tar industry, carbon industry, and coal ash utilization, (3) Natural gas: resource exploitation, transport, storage, and conversion technology, (4) Natural energy: hydraulic, solar, geothermal, wind power, oceanic and biomass energies, and (5) Others: waste resources, hydrogen and alcohol. On R & D trend of energy conversion technology, combustion theory, boiler, engine, thermal energy system, and high-efficiency power generation technology are described. Environmental problems and their protective technologies are also described

  9. Technology of latent-heat recovery for boiler system; Boira ni okeru sennetsu kaishu gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Moriyama, T. [Tokyo Gas Co. Ltd. (Japan)

    1996-08-01

    The boiler has reached the highest degree of completion among combustion equipment and is highly efficient. In order to enhance its efficiency further, it is ordinary to recover the retention heat of the combustion exhaust gas, but due to the problem of low temperature corrosion caused by the sulfur content in fuel resulted from a temperature drop of the exhaust gas, heat recovery has been done not sufficiently. In this article, an example is introduced to plan the betterment of efficiency by application of a latent heat recovering economizer to a sugar manufactory and a report is made on the energy saving effect by recovering the latent heat and a study on the quality of the material for the latent heat reclaimer. The above latent heat reclaimer is a system which takes advantage of the feature of the natural gas reportedly having no sulfur content, brings down the temperature at the outlet of a heat exchanger of the boiler exhaust gas to below the dew point, thereby recovers the condensed latent heat of the vapor in the exhaust gas and utilizes it for heating up the boiler feed water. In this example, the line of an already installed boiler has been partially modified and only a latent heat reclaimer has been installed newly. The increase of efficiency has been as high as 5.28%. 5 figs., 5 tabs.

  10. Survey of Joint Implementation activities in China; Chugoku ni okeru kyodo jisshi katsudo kanren chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    It is a large task for Japan to positively promote the Joint Implementation activities related to the United Nations Framework Convention on Climate Change. Rapid increase in the emission of greenhouse-effect gases, especially CO2, is predicted in China with remarkable economic growth and population of 1.2 billion. It is essential to promote the Joint Implementation activities in China. In this survey, framework, organization, problems and tasks were investigated to effectively promote the Joint Implementation activities in China. Construction of framework for the real Joint Implementation activities has been proposed. Current problems for promoting the Joint Implementation activities in China are that the distinct guideline for the Joint Implementation is not established in the government, that the receiving system including receiving, planning and arranging sections is not established, and that the burden problems for the costs of project evaluation, data acquisition, monitoring, and verification are not solved. 5 refs., 21 figs., 6 tabs.

  11. Present status of geothermal power development in Kyushu; Kyushu ni okeru chinetsu hatsuden no genjo

    Energy Technology Data Exchange (ETDEWEB)

    Akiyoshi, M. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

    1997-10-20

    The present situation was introduced of the geothermal power generation in Kyushu. In Kyushu, where there are lots of volcanos and abundant geothermal resources, the geothermal exploration has been made since long ago. Three non-utility use units at three geothermal power generation points and six commercial use units at five points are now in operation in Kyushu. The total output is approximately 210 MW, about 40% of the domestic geothermal power generation. At Otake and Hacchobaru geothermal power plants, the Kyushu Electric Power Company made the geothermal resource exploration through the installation/operation of power generation facilities. At the Otake power plant, a geothermal water type single flashing system was adopted first in the country because of its steam mixed with geothermal water. At the Hacchobaru power plant, adopted were a two-phase flow transportation system and a double flashing system in which the geothermal water separated from primary steam by separator is more reduced in pressure to take out secondary steam. Yamakawa, Ogiri and Takigami power plants are all for the joint exploration. Geothermal developers drill steam wells and generate steam, and the Kyushu Electric Power Company buys the steam and uses it for power generation. 5 figs., 1 tab.

  12. Dissipative structure of mechanically stimulated reaction; Kikaiteki reiki hanno ni okeru san`itsu kozo

    Energy Technology Data Exchange (ETDEWEB)

    Hida, M. [Okayama Univ., Okayama (Japan). Faculty of Engineering

    1994-12-20

    Recently various studies have been conducted concerning the state changes of materials obtained through mechanical alloying (MA) or mechano-chemical (MC) processing. What is noticeable is the quasi-steady state of almost all the materials obtained through various processes including MA and MC, and that the super cooling, supersaturating and high residue distortion realized under unbalanced conditions have not been clarified. In other words, the tracing capability to the external binding conditions is low. In this report, the appearance of the high temperature phase and high pressure phase obtained through MA or MC processing, the forming of amorphous, the mesomerism of the amorphous materials, the interesting phenomena generated by combination between the mechanical disturbance and chemical reactions were discussed with concrete examples, and a steady dissipative organization theory was approached from the viewpoint of dissipative structure development which is equal to the forming process of the quasi-steady phase. 34 refs., 2 figs.

  13. Radio communication for motor sports; Motor sports ni okeru musen tsushin

    Energy Technology Data Exchange (ETDEWEB)

    Ota, K. [Kenwood Corp., Tokyo (Japan)

    2000-02-01

    This paper describes general radio communication, and radio telephone and data communication for motor sports. The radio communication for racing cars is largely disturbed by car noises and peripheral noises. The adverse effect of noises caused by on-board computer on communication, and that of radio waves on a computer are unavoidable. The radio communication is also disturbed by various radio devices in a racing circuit. As disturbance measures, change of radio frequency and filtering are necessary. For the radio telephone communication between a driver and a manager or a manager and team staffs, a close-talking microphone or a microphone with a noise canceler are used to pick up proper voices from strong roaring. However, although the frequency band of engine noises is nearly equal to that of human voices, separation of voices is extremely difficult. The car data during racing are transmitted rapidly to a pit by microwave communication, and used for the planning of a race strategy in a pit. (NEDO)

  14. Study on the time-domain electromagnetic responses; TDEM ho ni okeru denji oto ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Noguchi, K.; Endo, M. [Waseda University, Tokyo (Japan). School of Science and Engineering

    1997-05-27

    With an objective to perform three-dimensional analysis with high accuracy in using the electromagnetic exploration method, characteristics in electromagnetic response were analyzed, and conditions for acquiring necessary data were discussed. The discussion defined a parameter called `response anomaly` which uses response from media to standardize response only from substances with abnormal resistivity. The receivers were located uniformly on the same plane, and the response anomaly was derived from electromagnetic response from each of the three horizontal and vertical components at each receiving point, which was expressed as a contour map. The parameter for the abnormal body was consisted of location and resistivity contrast with media. Discussions using the contour map were given on the response when these factors for the parameter were varied. As a result, it was found that the response anomaly appears in the form that reflects the abnormal body, and the response anomaly of the horizontal component is superior in terms of being large. It was also referred that, as a requirement for the abnormal body which gives larger impact from the electromagnetic response, the abnormal body should have lower resistivity than that in the media, and resistivity contrast with the media should be greater. 2 refs., 7 figs., 1 tab.

  15. Autosolvent effect of bitumen in thermal cracking; Netsubunkai hanno ni okeru bitumen no jiko yobai koka

    Energy Technology Data Exchange (ETDEWEB)

    Mikuni, M.; Sato, M.; Hattori, H. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology; Nagaishi, H.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-10-28

    Tar sand bitumen is petroleum-based ultra-heavy oil, and has a great amount of reserve like coal. However, there are still a lot of problems for its highly effective utilization. This paper discusses whether the light components in bitumen show independent behavior during the thermal cracking of heavy components, or not. Solvent effect and reaction mechanism during the thermal cracking are also derived from the change of their chemical structures. Athabasca tar sand bitumen was separated into light and heavy fractions by vacuum distillation based on D-1660 of ASTM. Mixtures of the both fractions at various ratios were used as samples. Negative effect of the light fraction on cracking of the heavy fraction was observed with dealkylation and paraffin formation Polymerization of the dealkylated light fraction to the heavy fraction was suggested due to lack of hydrogen in the thermal cracking under nitrogen atmosphere, which resulted in the formation of polymer. 3 refs., 6 figs.

  16. Role of advanced technology in mechanical engineering. Kikai kogaku ni okeru cho no yakuwari

    Energy Technology Data Exchange (ETDEWEB)

    Koda, T. (Mechanical Engineering Lab., Tsukuba, Ibaraki (Japan))

    1992-10-05

    Since technology prefixed with 'super' is ultra-technology in another word, two kinds of work are introduced, that are on-going in the ultra-technology section in Mechanical Engineering Lab., the Ministry of International Trade and Industry. It is noted therewith that in order to realize 'super', introduction of knowledge of unfamiliar fields to mechanical engineering is one of ways. The first is a research on ion-injection onto solid surfaces by introducing quantum mechanics to mechanical engineering. Possibility of rotating new materials and physical properties is under investigation using MeV ion injection equipment. The second is a research on named 'cozy machine'. This is an example of introduction of physiological knowledge and is based on the concept that an operator can handle his machine pleasantly if it is controlled with his proper biorhythm. The possibility to form 1/f sway related to being cozy is shown using electrocardiographic signals upon which the interval of an R wave showing the largest amplitude is determined. Rotating machines are controlled in proportion to the potential. 13 refs., 3 figs.

  17. Improvement works of water quality in the enclosed area. Heisasei kaiiki ni okeru suishitsu kaizen jigyo

    Energy Technology Data Exchange (ETDEWEB)

    Sega, Y. (Ministry of Transport, Tokyo (Japan))

    1993-08-10

    This paper introduces specific examples of measures to preserve and improve water quality as adopted in the harbor environment administration to prevent pollution and create comfortable environments. In the investigation of ocean bottom purification, a test construction has been carried out using a sand covering method at Mikawa Bay. The sand covering method uses good quality sand to cover sludge on the ocean bottom to suppress dissolution of nutrients that have been revolving from the ocean bottom sludge into sea water. The method also reduces dissolved oxygen consumption in sea water by the ocean bottom sludge and improves the water quality in the area and the ecosystems. In the change of ocean bottom sludge quality in vertical distribution in the sand covered area, the COD content decreased more largely than in the current ocean bottom, but it increased more largely with lapse of time during which floating mud has precipitated. The 'sea blue' technology development project intends to implement the following activities compositely: advancement of environment improving technologies that utilize natural purification ability; environmental improvement including sludge dredging, and improving water quality and ocean bottom quality; improvement of green areas that are highly friendly with water; and application of measures to form amenity spaces. 8 figs., 3 tabs.

  18. Wood bioindustry in the 21st century. 21 seki ni okeru mokuzai bio kogyo

    Energy Technology Data Exchange (ETDEWEB)

    Haraguchi, T. (Research Association for systematic Utilization of Wood Components, Tokyo (Japan))

    1991-09-01

    For these about ten tears, technology has remarkably made progress to convert chemical contents of wood, i.e., cellulose, hemicellulose and lignin into effective materials. As for the fractionation of wood contents, a mutual bonding is noted to be physically or chemically made respectively among all cellulose, hemicellulose and lignin which are structural contents of wood cell wall. Therefore, each of those contents must be fractionated and separated to be converted and utilized, which methods comprise, among others, digestion and explosive crushing method, acetic acid digestion method, and fine powder saccharification method. For the chemical and biochemical conversion of fractionated contents, it was introduced that the hemicellulose is thoroughly hydrolyzed, converted into monosaccharide xylose, further reduced to xylitol and finally converted into xylooligosaccharide and reduced xylooligosaccharide. Also, butanediol can be biologically produced by conversion. As for the chemical and biochemical conversion and utilization of cellulose, the cellulose can be hydrolyzed to glucose with enzyme to derive sorbitol, acetone and acetic acid by fermentation, and many other kinds of material. 7 refs., 10 figs., 8 tabs.

  19. Wind turbine power generation projects supported by NEDO; NEDO ni okeru furyoku hatsuden shien jigyo

    Energy Technology Data Exchange (ETDEWEB)

    Higashino, M. [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1998-09-01

    The long-term energy supply/demand balance prospects, reviewed in 1998, revise the wind turbine power generation target greatly upward to 300,000kW by 2010. Outlined herein are the national wind turbine power generation projects promoted by NEDO. The wind power development field test projects investigated wind conditions in detail at 94 sites, designed systems for 31 sites and installed/operated the systems at 13 sites during the FY1995 - 1998 period. The new energy enterpriser support projects tend to be concentrated in the coastal areas facing the Sea of Japan, from Hokkaido to Tohoku/Hokuriku districts, having an annual average wind velocity in a range from 5.3 to 6.2m/s at a height of 20m from the ground. The wind turbine capacity ranges from 800kW as the minimum eligible level for the national project to 20,000kW. It is expected that the project produces relatively good results at each site. The local new energy introduction promotion projects, supported by local autonomies, have been spreading throughout Japan since FY1997. The locally supported projects are expected to be more profitable than the national projects. 4 figs., 6 tabs.

  20. Exploration under pavement by electromagnetic subsurface profiling. Hosoka ni okeru roban rosho heno haaku

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, C.; Miyatsu, Y.; Seki, M. (Construction Project Consultant Co. Ltd., Osaka (Japan))

    1994-05-01

    This paper reports explorations on change in roadbeds and subgrades under pavement by means of an electromagnetic wave method (underground radar method). The paper summarizes the measurement principle of this exploration method, the measurement equipment (consisting of a control unit, an antenna unit, and an image output unit), and data analysis and processing. It is indicated that the quality of the exploration result is governed by the antenna used, whereas a reference is shown for selecting antennas according to the exploration objects (embedded pipes, underground cavities, and pavement thickness) and depths of the explorations. The paper then lists examples of explorations conducted by using antennas with a frequency of 500 MHz. The explorations include the following cases: cavities directly below concrete seals (with a thickness of 10 cm), hume pipes (with a diameter of 10 cm) embedded in a depth of 1.1 m under asphalt pavement, clearances existing in subgrades, loosened ground bed believed to have been caused by immersion, and clearances (depth of 70 cm) existing in ground beds behind bridge piers. 5 refs., 9 figs., 2 tabs.

  1. Geophysical exploration in environmental engineering; Kankyo engineering ni okeru butsuri tansa

    Energy Technology Data Exchange (ETDEWEB)

    Shima, H. [OYO Corp., Tokyo (Japan)

    1997-12-01

    This paper describes underground environmental issues to which geophysical exploration can be applied. Especially, ground pollution, waste treatment and unexploded ordnance (mine) detection are discussed by considering worldwide technology trends through examples in Japan and the USA. Since environmental surveys are generally conducted for regional and rather shallow ground, rapidity, economy and high resolution are required for geophysical exploration. In response to these demands, a mapping system using capacitor electrodes and a complex resistivity method for detecting organic compounds are promising for the electrical prospecting. A shallow electromagnetic method is being standardized for the electromagnetic prospecting. A cesium magnetic gradient meter is also being standardized for the magnetic prospecting. An underground radar, seismic prospecting, and gravitational prospecting are also applied to some grounds. Prospecting of pollution sources, high- and low-concentration ground pollution, monitoring of pollutant removal, soundness survey of water barrier in management-type waste treatment place, and detection of unexploded ordnance are illustrated for the examples. 15 refs., 10 figs., 4 tabs.

  2. Education for hydraulics and pneumatics in Nihon University; Nihon Daigaku ni okeru yukuatsu kyoiku

    Energy Technology Data Exchange (ETDEWEB)

    Ouchi, M. [Nihon Univ., Chiba (Japan). Coll. of Industrial Technology

    2000-03-15

    Described herein is education of hydraulics and pneumatics in Nihon University. Department of Mechanical Engineering of Faculty of Production Engineering has been holding up the educational aims of bringing up engineers and researchers who have ability and intelligence to cope with internationalization and contribute to society, and of bringing about creativity, among others. Control equipment is an optional subject for the sophomore class in the second semester, and is centered by mechatronics, including hydraulic and pneumatic control systems and equipment. The related subjects include fluid dynamics, control engineering, system controlling, hydraulic machines, robotics and automobile engineering. The drill course includes disassembling and assembling gear pumps, drills on pneumatic devices, system behavior and mechatronics, experiments on fan and hydraulic control circuits and on servo mechanisms, and machinery designs and drawings. Seminars are led by full-time or part-time lecturers for the themes related to hydraulic power. Many students are interested in hydraulic and pneumatic themes for their graduation theses, because of their relations with control, environments, energy saving and so on. We are now in the age of composite technologies, and hydraulic power basics are prerequisite for engineers, and important for education of students. (NEDO)

  3. Development of a platoon driving AHS; AHS jikkensha ni okeru gunsoko seigyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Seto, Y.; Inoue, H. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    Nissan and the Public Work Research Institute of the Ministry of Construction are developing an Automated Highway System. We are investigating a longitudinal control system in AHS. In this paper, a vehicle control method using two actuators an engine and a brake, is described. Experimental and simulated results are shown. A Platoon driving control method using road-to-vehicle and vehicle-to-vehicle communication is described. And the influence of the communication on the control performance is shown by experiments and simulation. The effects of the communication device and control device mentioned above are verified by experimental results in an AHS field test conducted in September 1996 on a dosed highway. 5 refs., 8 figs.

  4. Magnetic prospecting in Kaibuki-yama ancient tomb; Kaibukiyama kofun ni okeru zenjiryoku sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Nishitani, T. [Akita University, Akita (Japan). Mining College

    1996-10-01

    Kaibuki-yama ancient tomb located in Kumeda, Kishiwada City, Osaka has a square shape in the front and an orbicular shape in the rear, which was considered to be made in the 4th century. This ancient tomb has a total length about 135 m, a diameter of orbicular shape in the rear about 82 m, and a height about 9 m, which is a symbolical existence of the Kumeda ancient tombs. Stone chamber and stone casket made of Sanbagawa crystalline schist or rhyolitic-andesitic tuff are expected in this tomb. Magnetic prospecting in this study is accompanied with this survey. A differential type proton magnetometer was used for the measurements, which were conducted using meshes with 1 m edges. A pair of distinct positive and negative magnetic anomalies were observed in the center of orbicular shape in the rear. This coincides with a location of main body buried, which is archaeologically estimated. The magnetic anomaly might be caused by the article buried in the tomb, such as ironware, based on the measurement of magnetic intensity. From the calculated values of magnetic anomaly using a model, the buried article with magnetic anomaly was considered to have a size with length of 1 m, width of 0.1 m, and height of 0.2m. The negative magnetic anomaly could not be explained only by this. It is necessary to consider the other reasons. 8 refs., 8 figs.

  5. Characteristics of microtremors in Hanshin area; Hanshin chiiki ni okeru bido no kihon tokusei nitsuite

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H.; Suzuki, K.; Yamanaka, H.; Seo, K. [Tokyo Institute of Technology, Tokyo (Japan)

    1996-10-01

    To increase general understandings of fundamental characteristics of microtremors in Hanshin area, microtremors have been observed at Sumiyoshi River-side, Rokko Island, and Nishinomiya. Relations were discussed among the stability of predominant period, successive fluctuation and meteorological conditions. For the analysis, cosine-type taper was conducted before and after 10% of the observed records, and Fourier spectrum was calculated by smoothing using Parzen window with a band width 0.3 Hz. Geometrical mean of two components was used as a horizontal component. At the observation points except Sumiyoshi River-side, predominance in the short period side was not distinct, and was not stable due to the successive fluctuation of predominant period. However, there was less successive fluctuation of spectrum ratio between different two points in the band with period more than 1 sec. Since there was a close correlation between the successive fluctuation in this band and the wind velocity or air pressure, the microtremors in this band was affected by a single vibration source. Ground characteristics could be illustrated by the averages of ratio against base points of moving observation. 14 refs.

  6. Detailed seismic intensity in Morioka area; Moriokashi ni okeru shosai shindo bunpu

    Energy Technology Data Exchange (ETDEWEB)

    Saito, T.; Yamamoto, H.; Settai, H. [Iwate University, Iwate (Japan). Faculty of Engineering; Yamada, T. [Obayashi Road Construction Co. Ltd., Tokyo (Japan)

    1996-10-01

    To reveal a seismic intensity distribution in individual areas, a large-scale detailed seismic intensity survey was conducted in Morioka City through questionnaire, as to the Hokkaido Toho-oki (HE) earthquake occurred on October 4, 1994 with a record of seismic intensity 4 at Morioka, and the Sanriku Haruka-oki (SH) earthquake occurred on December 28, 1994 with a record of seismic intensity 5 at Morioka. A relationship was also examined between the seismic intensity distribution and the properties of shallow basement in Morioka City. The range of seismic intensity was from 2.9 to 4.6 and the difference was 1.7 in the case of HE earthquake, and the range was from 3.1 to 5.0 and the difference was 1.9 in the case of SH earthquake. There were large differences in the seismic intensity at individual points. Morioka City has different geological structures in individual areas. There were differences in the S-wave velocity in the surface layer ranging from 150 to 600 m/sec, which were measured using a plate hammering seismic source at 76 areas in Morioka City. These properties of surface layers were in harmony with the seismic intensity distribution obtained from the questionnaire. For the observation of short frequency microtremors at about 490 points in the city, areas with large amplitudes, mean maximum amplitudes of vertical motion components more than 0.1 mkine were distributed in north-western region and a part of southern region. 4 refs., 9 figs., 1 tab.

  7. Mechatronization of rotating machines in plant; Plant ni okeru kaiten kikai no mechatronics ka

    Energy Technology Data Exchange (ETDEWEB)

    Kikuchi, H. [Chiyoda Corp., Tokyo (Japan)

    1993-10-01

    This paper introduces mechatronization of rotating machines in a plant, with application examples of electronic governors as the main subject. For centrifugal compressors, design and fabrication of anti surging control system have become possible by using a programmable logic controller (PLC) and a distributed control system (DCS) with fine scanning time. An electronic governor for turbine control has been added with a function to control amount of power generated by a motive force recovery device in a flowing catalytic cracking equipment by means of an expander inlet valve. This has made possible to operate the motive force recovery device automatically even under a low load operation. With an electronic governor to control supply and receipt amount of steam to and from an existing plant, the governor valve opening angles were so controlled that actual steam header pressure matches the setting, whereas the steam has become possible to be utilized without waste under normal operation. Operation of a comprehensive compressor/turbine monitoring system on DCS, operation of centrifugal compressors of two casings by using electromagnetic bearings, and motor speed control with use of an inverter heve also become possible. 8 figs., 2 tabs.

  8. Cogeneration system at the Showa Shell Sagamihara shopping center. Sagamihara shopping center ni okeru sekiyu cogeneration

    Energy Technology Data Exchange (ETDEWEB)

    Kameda, H. (Showa Shell Sekiyu K.K., Tokyo (Japan))

    1994-03-31

    This paper introduces a cogeneration system at the Showa Shell Sagamihara Shopping Center. The Center assumes a peak power demand of 4000 kW, thereby using utility power (not connected to the cogeneration system) at 2000 kW, and generating power by using three 1000-kW diesel engine generators. The waste heat utilizing facility consists of three steam waste heat boilers with a capacity of 614 kg/h and a pressure of 9 kg/cm[sup 2]. The steam is used as a heat source for absorption type freezers, and to recover hot water through plate-type heat exchangers. Two after-burning boilers of 2.5 tons/hour are also used to supplement shortage of steam at power peaks for room cooling with the number of boilers adjusted. The absorption-type freezer consists of two steam double-effect 500RTs which perform air conditioning by circulating cold water. A 150 RT motor-driven turbo freezer has also been installed to cover peak power demand in the summer season. All the facilities have been installed in the basement to minimize influence of vibration and noise to the surrounding districts. NOx emission has been suppressed to 400 ppm or lower by means of ammonia reducing denitrification. Low-sulfur heavy oil A is used to reduce SOx emission. The Center has obtained a specific supply permission to supply excess power of 2850 kW after in-house consumption of the power generated in the cogeneration system to the tenant shops in the Center. 7 figs., 2 tabs.

  9. Challenge of the global warming-JAMA. Chikyu ondanka mondai to jidosha sangyo ni okeru torikumi

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Y. (Japan Automobile Manufactures Association Inc., Tokyo (Japan))

    1993-04-01

    This paper summarizes the global warming problem challenged by the Japan Automobile Manufacturers Association. An investigative analysis was carried out on CO2 related data. Its gists are described as follows: The rate of contribution to CO2 emission in the automotive sector is about 17%; fuel consumption improvement has long been discussed, but is in a trend of hitting the ceiling because of the needs of mounting gears for safety improvement and of vehicle upsizing; amount of fuels used is increasing year after year; the rate of the increase correlates with the economy growth; the growth of CO2 emission from automobiles would be smaller than the values given in several reports as a result of the Japanese economic growth lower than the anticipation; effects of the fuel consumption improvement are assumed to reduce CO2 emission by several percentage points in 2000; electric vehicles could reduce CO2 emission by 40% per car if nuclear power generation is partly used; fluorocarbon used in the automobile industry is for foaming, rinsing and air conditioners, with its use in the former two applications being planned to be totally abolished; and the problem thereof exists in air conditioners, for which recovery, leakage measures, and conversion to new coolants are being discussed. 12 refs., 9 figs., 1 tab.

  10. Study of active noise control in ducts. Kanrokei ni okeru nodoteki soon seigyo hoho no kento

    Energy Technology Data Exchange (ETDEWEB)

    Nakao, Yoshiatsu

    1988-08-01

    On an active control to reduce noise in ducts, the theoretical and experimental studies of the energies ratio of the noise and the cancelling sound which should be produced by a speaker, were carried out. In case the cancelling sound was produced by the speaker which was set in the branch duct, the energies ratio varied with the setting position, the length and the cross section of the branch duct and the frequency of the noise. As the non-dimensional length of the branch duct was drawing near 0.5, the energies ratio became small. But when the non-dimensional length was 0, the ratio did not become smaller than 1. The experimental test confirmed that it was possible to reduce the noise by the cancelling sound which energies ratio was as small as about one hundredth of the noise. In case the noise was the pure sound, and the wave-length was over one fourth of the duct diameter, it was possible to reduce the noise more than 40 dB. And in case the wave-length was one eighth the reduction quantity was about 20 dB. Therefore, in case the noise is the pure sound or close to the pure sound, it is possible to apply the active noise control. 5 references, 23 figures.

  11. Refraction experiment in the Kobe-Hanshin area; Kobe Hanshin kan ni okeru kussetsuho tansa

    Energy Technology Data Exchange (ETDEWEB)

    Koketsu, K. [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

    1996-05-01

    The refraction experiments were conducted to investigate the underground structures reaching the basement by analyzing the results of the artificial earthquakes the explosion earthquake research group produced in City of Kobe and the Hanshin District on December 12 to 15, 1995. Considering that noise level can exceed 1 mkine in an urban area even in the mid-night, the courses of traverse were drawn focusing on Points S2 through S4 and U1. The earthquake waves from Points S2 through S4 are generally low in amplitude. However, the major components of the signals have a dominant frequency exceeding 10Hz, which makes them distinguishable from urban noise having a lower frequency, contrary to the previous indication that such a low-amplitude wave might not be distinguishable. On the other hand, the signals from the explosion at Point 4 in Awaji Island cannot be distinguished in the urban area, even on the nearby course of traverse D. At present, the analytical group is organized to read various phases running and analyze the P-velocity structures. 2 refs., 10 figs., 1 tab.

  12. Load averaging system for co-generation plant; Jikayo hatsuden setsubi ni okeru fuka heijunka system

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, Y. [Fuji Electric Co. Ltd., Tokyo (Japan)

    1995-07-30

    MAZDA Motor Corp. planed the construction of a 20.5MW co-generation plant in 1991 for responding to an increase in power demand due to expansion of the Hofu factory. On introduction of this co-generation plant, it was decided that the basic system would adopt the following. (1) A circulating fluidized bed boiler which can be operated by burning multiple kinds of fuels with minimum environmental pollution. (2) A heat accumulation system which can be operated through reception of a constant power from electric power company despite a sudden and wide range change in power demand. (3) A circulating-water exchange heat recovery system which recovers exhaust heat of the turbine plant as the hot water to be utilized for heating and air-conditioning of the factory mainly in winter. Power demand in MAZDA`s Hofu factory changes 15% per minute within a maximum range from 20MW to 8MW. This change is difficult to be followed even by an oil burning boiler excellent in load follow-up. The circulating Fluidized bed boiler employed this time is lower in the follow-up performance than the oil boiler. For the newly schemed plant, however, load averaging system named a heat accumulation system capable of responding fully to the above change has been developed. This co-generation plant satisfied the official inspection before commercial operation according the Ministerial Ordinance in 1993. Since then, with regard to the rapid load following, which was one of the initial targets, operation is now performed steadily. This paper introduces an outline of the system and operation conditions. 10 refs.

  13. Guarantee of property right in opean access systems; Open access ni okeru zaisanken no hosho

    Energy Technology Data Exchange (ETDEWEB)

    Maruyama, M. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-12-25

    This paper describes discussions in California of the USA and in Germany concerning the separation of transmission department and forced liberation of transmission network in private electric power companies and the guarantee of property right. In California, the state public utility committee does not have an authority to order the separation of transmission department against electric power companies. It is only the legislature that can conduct the separation of transmission department and the third party access of transmission network based on the expropriation provisions of the constitution. In Germany, the order of separation of transmission department by the readjusting authority contradicts the guarantee of property right in the constitution. The order of third party access also exceeds the range of duty accompanied with the property right, and the procedure of expropriation is necessary for its enforcement. Problems are pointed out in the case when these discussions are applied to the separation of transmission department, third party access, and distribution system in Japan. 3 refs.

  14. Role of geophysical exploration for civil engineering; Doboku chosa ni okeru butsuri tansa no yakuwari

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, S.; Sato, S. [OYO Corp., Tokyo (Japan)

    1997-12-01

    This paper describes the current status of applying geophysical exploration to civil engineering works, application examples of latest geophysical exploration technologies in typical civil engineering fields (dams, tunnels, banks, and civil engineering works in urban areas), and of geophysical exploration technologies specially devised at civil engineering work sites. The applications include utilization in rock classification and weathering division, estimation of grouting effect and its injection scope, determination of loosening as a result of tunnel excavation, utilization of the relationship between S-wave velocity and N-value revealed by the standard penetration test, and tunnel front exploration. A well logging technique utilizing boring holes is available as a latest technology. Tomography technology using elastic waves, specific resistance and radar has its application increased as it is used in dams, tunnels, and foundations of other important structures. Attempts are made on application of explorations using the shallow bed reflection method and three-dimensional exploration method. Frequently used technologies include seismic exploration using the refraction method for dams, high-density electric exploration for tunnels, electric exploration for banking, and PS logging using the suspension method for structure foundations. 30 refs., 13 figs., 5 tabs.

  15. Petroleum exploration and production in Japan; Nihon kokunai ni okeru sekiyu tanko to seisan

    Energy Technology Data Exchange (ETDEWEB)

    Kamon, M.

    2000-02-01

    The production of crude oil was started even in Japan from the nineteenth century to the twentieth century beginning in Niigata Prefecture, and the real petroleum industry was produced. The production has been started even in Akita Prefecture in the age in Taisho and Showa. The petroleum industry in Japan developed from the comparatively old like this. However, it is not very much known generally. Because of the oil of output is fewer than an amount of import from foreign countries. This paper describes oil gas rice pad in Japan and the production situation. (NEDO)

  16. SWD experiment at Southwest Andrews oil field; Nansei Andrews yuden ni okeru SWD jikken

    Energy Technology Data Exchange (ETDEWEB)

    Kozawa, T.; Tsuru, T. [Japan National Oil Corp., Tokyo (Japan)

    1998-04-01

    Seismic while drilling (SWD) is an accurate drilling method by which time-to-depth (T-D) information for determining the accurate bit location and information of bedding boundaries below the bit can be obtained. However, the signal level is rather low compared with the noise generated from the rig during drilling. It is required for improving the S/N ratio to calculate a correlation using reference signals simultaneously acquired using a pilot sensor which is a geophone attached to the rig. Some experiments were conducted in the Southwest Andrews Oil Field. Deterioration of data quality due to the noise particular to the SWD in this oil field could be reduced by proper data acquisition geometry including the minimum offset distance using a geophone array. In order to correct the time, a velocity of P-wave propagating the drill pipe was estimated using auto-correlation of the pilot traces. The S/N ratio was improved by the VSP deconvolution and the stacking effect during VSP-CDP conversion. Thus, could be obtained the accurate T-D information and reflection wave information below the bit. 12 refs., 19 figs., 1 tab.

  17. Noise characterization in SWD survey; SWD ni okeru noise ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Tsuru, T.; Ozawa, T. [Japan National Oil Corp., Tokyo (Japan)

    1998-02-01

    SWD (Seismic While Drilling) is located as one kind of the reverse VSP (Vertical Seismic Profiling) technology, and a working drill-bit is used as its energy-source. The SWD is carried out for a check-shot survey as well as a prediction ahead of the bit. The largest advantage of the SWD technology may be a prediction, while drilling, of a drilling hazard such as an abnormal pressure zone. On the other hand, a serious disadvantage exists in the data quality due to a contamination by large noises generated from a working rig, because the SWD survey is done `while drilling`. Regarding the characteristics of these noises, especially the noise received by surface geophones has not been clarified quantitatively yet. Through several field experiments, the authors have evaluated the characteristics. In this paper, the dominant frequency range of the surface geophone noise is discussed. Furthermore, the noise from the mud motor is also discussed. 9 refs., 13 figs.

  18. Steps of radioisotope separation in Japan; Nihon ni okeru doitai bunri no ayumi

    Energy Technology Data Exchange (ETDEWEB)

    Nakane, Ryohei [Institute of Physical and Chemical Research, Wako, Saitama (Japan); Kitamoto, Asashi; Shimizu, Masami [eds.

    1998-03-01

    The Extraordinary Specialist Committee on Radioisotope Separation of the Atomic Energy Society of Japan has supported various actions on foundation, application and industrialization of the radioisotope separation over past 30 years to continue wide range of actions at a standpoint of specialist, since established in Showa 44 (1969). On June 1993 (Heisei 5), a memorial lecture meeting, as the 100th committee was held at the Institute of Physical and Chemical Research (RIKEN) of Wako-city in Saitama prefecture. At that time, a planning to publish an impressive memorial issue, to prepare orbits and episodes of actions, painful stories and fault examples of developments, and so forth like novels and to use for a future foundation, was determined. For its writing principle, it was settled to the base not to use mathematical equation as possible, to collect the essence like a tale, to collect actual and historical reports, and so on. And, for its writing content, it was determined to report on actual, painful and fault experiences in research and development, on data, topics and human relation, and on what to be remained for references. This book can be used not only for data collected on traces from fundamental to applied studies, technical development for industrialization, and so forth on radioisotope concentration, but also for a knowledge bag to give some hints to a man aiming to overcome a new problem. (G.K.)

  19. Robotics in port construction. Kowan kensetsu ni okeru roboto ka gijutsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Sakai, Hiroshi (Ministry of Transport, Tokyo (Japan))

    1990-02-15

    To cope positively with the problems of securing labor, improving work environment, etc., mechanization and robotics in port and marine development are the urgent subjects. Technologies for robotics of various levels are being developed, coverning data acquisition, processing, display, recording simple automation, and high inteligent fuction which can automatically make such judgement as having been done by man. Some representative cases of technological development in the fields of robotics and mechnization being carried on by the Ports and Harbors Bureau in the Ministry of Transportaion are introduced. Technological develpment required for the mechanization of rubble mound foundation construction work has been carried on. A demonstration test was carried out at Kamaishi Port, proving the practicability of the technology. Robots are developed which can walk on the sea bottom to perform underwater investigation and unmanned operation. Underwater visual device and underwater position measurement device are provided as the supporing systems. Several tests were already performed in actual sea areas and the success of the development was verified. 3 figs.

  20. Moored observation of the Indonesia throughflow; Indonesia tsuka ryuiki ni okeru keiryu kansoku kekka

    Energy Technology Data Exchange (ETDEWEB)

    Kashino, Y. [Japan Marine Science and Technology Center, Kanagawa (Japan); Watanabe, H.; Yamaguchi, H. [Sanyo Techno Marine Inc., Tokyo (Japan); Aoyama, M. [Meteorological Research Inst., Tsukuba (Japan); Herunadi, B.; Hartoyo, D.

    1998-10-16

    This paper partially reports the observation in the southern part of the Philippine Sea of the Indonesian throughflow that JAMSTEC performed jointly with the Applied Agency of Indonesian Engineering Evaluation. From February 1994 to June 1995, two mooring systems were established between the Talaud Island and Morotai Islands to examine the ocean variability of the Indonesian throughflow. As a result, a strong northwestward flow (that carries the mixed sea water of intermediate water in the North Pacific and high salt water in the South Pacific) of which the maximum flow velocity reaches 60 m/s in the southern mooring system with the water depth of 300 to 700 m was observed in each winter of 1994 and 1995. A westward flow that carries the South Pacific water toward the Maluku Sea in summer was observed in the southern mooring system. In both mooring systems, oscillation was detected at intervals of approximately 50 days. 36 refs., 15 figs., 2 tabs.

  1. Report of radioactivity survey in Kanagawa Prefecture, in 1996; Kanagawaken ni okeru hoshanochosa hokokusho, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report summarizes the results of 1-year survey on the radioactivities in foods and environments in Kanagawa Prefecture and the uranium level in the surroundings of Japan Nuclear Fuel Co., Ltd. (JNF), a nuclear fuel processing plant. The survey of radioactivity or radiation level was made in environments and foods including rain water, tap water, agricultural and livestock products, marine products, etc. For these subjects, analysis of nuclides and determination of spatial radiation dose rate were performed using {gamma}-ray spectrometer. Only for rain water, the general {beta} level was also determined. The uranium levels was monitored in river water and bottom materials, soil, Undaria pinnatifida, a seagrass in river mouths, etc. The present results show that there was no problem for all subjects tested in respect of radioactivity. And the uranium level around JNF was also within the normal range. The mean intake of {sup 137}Cs was 0.085 Bq/Kg/day for the residents in the district of Hiratsuka Health Center and 0.077 Bq/Kg/day for those in the Yokohama city. Both levels were slightly higher than the previous ones. The survey results before and after the returns of nuclear powered ship were also within the normal range. (M.N.)

  2. Array TDEM survey at the Yufuin fault; Yufuin danso ni okeru array shiki TDEM tansa

    Energy Technology Data Exchange (ETDEWEB)

    Mogi, T. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Tanaka, Y.; Fukuda, Y. [Kyoto University, Kyoto (Japan). Faculty of Science; Jomori, N. [Chiba Electric Research Institute Co., Chiba (Japan)

    1996-10-01

    The array arrangement of receivers was studied to improve the resolution of LOTEM (long offset transient electromagnetics) survey. To eliminate the effect of underground structure from a source to a receiving point, continuous array arrangement from a source site is desirable. The survey at the Yufuin fault was carried out by arranging TEM receivers at intervals of 100m from the source. Since the synchronization between transmitting and receiving points by high-precision clock is essential, an amplifier for a flux gate magnetometer capable of measuring at four points at the same time was used. In the south plateau of the Yufuin basin, a relatively high resistivity stratum more than several tens ohm m exists at depth less than several hundreds meter, and a low resistivity stratum less than 10 ohm m exists under that. Those boundary depth increases toward the north up to 950m, and the depth subsequently decreases toward the north until the low resistivity stratum disappears. In addition, the uniform stratum of 1000m deep continues toward the north. Such precise resistivity structure around the fault was obtained by dense arrangement of measuring points. 4 refs., 7 figs.

  3. Fate of dioxins in aquatic environment; Mizukankyo ni okeru dioxin rui no dotai

    Energy Technology Data Exchange (ETDEWEB)

    Sakurai, T. [National Inst. for Environmental Studies, Tsukuba (Japan)

    1998-07-10

    Described herein is fate of dioxins in aquatic environments, from their estimated origins to behavior in the food chains. It is considered that dioxins and their congeners generally follow principle of superposition in aquatic environments, although reflecting changed environments they have underwent, in consideration of varying sources from which they originate, and their stability and transport-related properties. Therefore, the multivariable analysis is applied to correspondence of the four major dioxin compounds, which can explain the major concentration changes of the dioxins found in the sediments and soil in Lake Kasumi-ga-ura and the Bay of Tokyo and their peripheries, to their origins. Different dioxins behave differently in the food chains, as revealed by isotope ratios in the ecology. Mathematical models have been developed to estimate concentrations of the various media, and are expected to clarify their behavior in the environments. 32 refs., 3 figs., 1 tab.

  4. Evaluation technology of lead-free solders; Namari free handa zairyo ni okeru hyoka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamashita, M.; Shiokawa, K. [Fuji Electric Co. Ltd., Tokyo (Japan); Ueda, A. [Fuji Electric Corporate Research and Development,Ltd., Kanagawa (Japan)

    2000-09-10

    Solders mainly composed of tin and lead are currently in widespread use in semiconductor devices. However, in view of lead influences on the human body and environmental problems, lead-free solders have been in urgent demand. In this study, aiming to improve the solderability and reliability of a tin-silver solder, one of most promising lead-free solder materials, we have investigated elements to be added. Focusing on typical lead-free tin-silver solders and tin-lead eutectic solders, this paper describes the result of investigations into the mechanical properties solderability, micro structures of the solder materials and gas analysis in soldering. (author)

  5. Problems of adhering organisms in power stations. Hatsudensho ni okeru fuchaku seibutsu no mondai

    Energy Technology Data Exchange (ETDEWEB)

    Sakaguchi, Isamu (Central Research Inst. of Electric Power Industry, Tokyo (Japan))

    1989-01-05

    Much seawater is used in thermal power station in Japan to cool condensers but organisms adhered on the water channel system result many troubles such as increase of flowing resistance, reduction of thermal transfer efficiendy, corrosion or erosion-corrosion of condenser pipes, and cleaning difficulty for periodic inspection. Living organisms range from micro bacteria of 2 mum to oysters and others of about 10cm size. For these reasons, the intake open channel is previously designed to larger size and this margin is called the shellfish allowance. Mussels which adhere most on circulating water channels, are one of Bivalvia, grow to 3-6cm and in maximum case to 9cm in a year. These adhere on the surface base by secreting adhesive disc consisting of byssus. Barnacles are one of Crustacea and their larvas search preferable places as to light, roughness and water flow and can adhere on a place in considerably rapid water flow. Other organisms are bacteria and Hydrozoa. Many problems are caused by these organisms even now. 8 refs., 3 figs., 2 tabs.

  6. Measures taken for recycling at beer breweries; Beer kojo ni okeru saishigenka eno torikumi

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, M. [Kirin Breweri Company, Tokyo (Japan)

    1999-08-05

    Full recycling of waste was achieved in our all breweries in 1998. This paper introduces the history to solve the problems relating to waste in our beer brewerise, our basic consideration for recycling, the status of waste generation and recycling activities, our measures taken for recycling and its relating cost, and in addition, the general measures taken by our industry as a whole. (author)

  7. Human physiology and psychology in space flight; Uchu hiko ni okeru ningen no seiri to shinri

    Energy Technology Data Exchange (ETDEWEB)

    Murai, T. [National Space Development Agency of Japan, Tokyo (Japan)

    1999-10-05

    Human beings' adaptation to space and the effects on them of a prolonged stay in space are discussed. Some effects may be detrimental to crewmen even when they are medically judged as 'normal' and 'adaptable.' Bone deliming, muscular atrophy, and hypodynamia may be physiologically 'normal' and 'adaptable' in the zero-gravity environment where no strength is required to hold a position or attitude, and they will not cause any serious problems if crewmen are to stay in the zero-gravity environment permanently. Astronauts work on conditions that they return to the earth, however, and they have to stand on their own legs when back on the ground. Such being the case, they in the space vehicle are forced to make efforts at having their bone density and muscular strength sustained. It is inevitable for a space station to be a closed, isolated system, and the crewmen have to live in multinational, multicultural, and multilingual circumstances in case the flight is an international project. They will be exposed to great social and psychological stresses, and their adaptability to such stresses presents an important task. (NEDO)

  8. Port construction projects in Sabah, Malaysia; Malaysia Sabah shu ni okeru kowan koji

    Energy Technology Data Exchange (ETDEWEB)

    Fukuwaka, M.; Ichinose, Y. [Kawasaki Steel Corp., Tokyo (Japan)

    1996-04-15

    This paper introduces civil engineering circumstances in Sabah, Malaysia through harbor constructions in the past decade. The state of Sabah has a large number of good natural harbors with coast lines formed complexly, and these harbors are managed and operated by the Sabah Harbor Department since 1968. The first two-decade long-term plan (1976 to date) has developed major harbors, and the second two-decade plan (1992 to 2012) has selected important harbors and is moving new improvements forward. Export of woods and imports of general consumer goods and industrial products had been the major activities of the ports before the 1980`s, while wood export has changed from logs to lumbers, and palm oil export and fertilizer import have increased after the 1990`s. The paper describes renewal and expansion constructions of harbor facilities at Kota Kinabalu Port, and constructions at the harbor for rationalization in containerization, and for building a movable pier for ferry use. At Lahad Datu Port, constructions for building container yards and new piers are in progress as the expansion constructions as of 1996. Because the construction sites are located in maritime tropical rain forest climate with high temperature and much rainfall, attentions are paid on concrete placement temperatures and quality control. 7 figs.

  9. Advanced technology trend survey of micromachines in Europe; Oshu ni okeru micromachine sentan gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    In this research survey, the development trend of micromachine technology in Europe was surveyed, development level of micromachine technology of European companies was grasped, and practical application fields of their target were investigated. Technology development level of private companies in Japan`s national projects and practical application fields of Japan`s target were arranged. Trends of micromachine technology development are compared between Japanese companies and European companies. Among micromachine technology development projects in Europe, ``8520 MUST`` is a part of the ESPRIT Project. About 40,000 companies among about 170,000 companies in whole Europe are relating to the MUST Project. The main fields include the manufacturing technology, process control of machines, technology of safety, sensor technology in environmental fields, and automotive technology. The marketing fields of application include the automobile, military technology, home automation, industrial process, medical technology, environmental technology, and games. The results can be compared with the direction of research and development in Japan. 22 figs., 8 tabs.

  10. Clean energy and agriculture. 5. ; Utilization of biomass for energy. Clean energy to nogyo. 5. ; Biomass energy no riyo

    Energy Technology Data Exchange (ETDEWEB)

    Haga, K. (National Institute of Agro-Environmental Sciences, Tsukuba (Japan))

    1992-10-01

    This paper reviews characteristics of biomass energy, which is regarded as renewable and clean, and present features of its utilization as well as their problems. Biomass energy resources are substantially such cultivated plants as saccharine crops, fatty and oily crops, petroleum plants, and aquatic plants. In addition, organic waste including agricultural and livestock waste is also the other important resource. Utilization of biomass for energy can be realized through applying such conversion technologies as methane fermentation, alcoholic fermentation, and thermal decomposition to the biomass resources. For the utilization, it is most important to make much of the viewpoints such as durable utilization corresponding to reproduction, competitive relation with food crops, and environmental protection. Biomass energy should be thought to be strictly limited to small-sized and regionally distributed energy. Therefore, it will be said that agriculture is appropriate to utilize biomass energy because it can practice both production and utilization of the biomass. 22 refs., 2 figs., 4 tabs.

  11. Technologies and techniques for analysis and use of genome information, 1997; Genome joho kaidoku riyo gijutsu no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper clarified the whole image of cell functions by elucidating the function and manifestation control mechanism of genes existing in genomes, and the network of their interactions, and surveyed applicability of the useful functions obtained of cells and proteins to the industrial field. The survey was made from a viewpoint of the fields of both biology and information science. Especially, based on the function-known DNA base sequence database, the following technologies were surveyed: technology to predict the function of the function-unknown DNA base sequence, search/separation technology to acquire the genes to be functionally elucidated in a state of being suitable for manifestation, technology to get perfect proteins by effectively manifesting the genes to be functionally elucidated, and technology to analyze the function of the proteins obtained by manifestation of genes. Further, the International Symposium was held which is titled `Genome Research Opens a New World to Bioindustry (New Developments in Genome Informatics Technologies). With the future progress of technology to decipher and use genome information, the construction of much newer genome industry is anticipated. 165 refs., 44 figs., 10 tabs.

  12. Research trend survey on the stable isotope utilization technology; Antei doitai no riyo gijutsu ni kansuru kenkyu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report reviews the activities and the trends in the area of the stable isotope use attracting attention recently. In the medicine and clinical treatment sector, the remarkable trends are the extension of {sup 13}C use. The breath test and the magnetic resonance spectroscopy (MRS) diagnosis have been developed as inspection methods. It is noted that investigation has been initiated on the magnetic resonance imaging (MRI) using {sup 3}He and {sup 129}Xe for the lung imaging. In the organic chemistry and biochemistry sector, the stable isotopes are used for analyzing the structures of complicated natural compounds and materials relating to life science and for analyzing the chemical reaction mechanism of organic compounds. In the nuclear energy sector, {sup 10}B and {sup 7}Li have been used as neutron absorption materials and pH neutralizing reagent, respectively. In the analysis and measurement sector, the process of isotopic dilution is used for the environmental analysis of trace elements including harmful substances. Among various separation methods of isotopes, well studied uranium enrichment processes and deuterium separation processes are described. Separation of {sup 15}N by ion exchange resin method and plasma ion cyclotron resonance (ICR) isotope separation have been studied, recently. 133 refs., 53 figs., 7 tabs.

  13. Advanced high temperature fluid technology development using microgravity environment; Bisho juryoku kankyo riyo kodo koon ryutai gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Behavior of gas/liquid two-phase flow in tubes and behavior of air bubbles in liquid were investigated under the microgravity environment without convection by using the drop test facilities of the Japan Microgravity Center. To remove bubbles in the liquid under gravity, the strength of surface tension acting on the gas/liquid interface was made inhomogeneous. In this case, the moving velocity of bubbles on the gas/liquid interface was able to be raised up to the maximum of 2.4 mm/s. For the movement of bubbles in the horizontal direction under the condition of low relative velocity independent of the size of air bubbles in the duct, bubbles moving in the horizontal direction under 1g flowed almost linearly accompanying with the liquid flow. For the air bubble distribution in the bubble flow, where small bubbles flow in the vertical tubes, the fluid pattern of air bubble flow under 1g and {mu}g depended greatly on the initial condition of mixed bubbles. Fundamental data were obtained, as for the transportation and control of multicomponent bubbles, bubbles in the sound field, and bubbles in the liquid phase by magnetic force, and the fluid phenomena of bubbles in the subcool boiling region, a single bubble in the gradient electrical field, and bubbles in the tubes with small diameter. 47 refs., 97 figs., 8 tabs.

  14. `Power storage system` dealing with leveling of electric power use; Denryoku riyo no heijunka ni kotaeru `denryoku chozo system`

    Energy Technology Data Exchange (ETDEWEB)

    Igarashi, M. [Meidensha Corp., Tokyo (Japan)

    1996-06-28

    An overview is given on the development situation of a Zn-Br battery as a power storage system. The system is aimed at storing excess power at night and supplying the on-load demand during daytime. The power storage technology requires a large output and capacity of MWh level, long term stability and durability, and cost as low as pumped storage power generation. Four kinds of batteries have been examined to cope with the conditions, in which development of Zn-Br batteries along with Na-S batteries is in progress towards practicability. As a power conversion method for this system, GTO has been employed for a large capacity unit and IGBT for a medium/small capacity unit. The reliability of the Zn-Br batteries against leakage was improved by laminating each cell by hot plate welding. The service life was improved by using a material with a high bromine resistance in place of the conventional electrode constituent material. Although the battery efficiency was influenced by each resistance of electrode, film and electrolytic solution, distance between electrodes, temperature, etc., these correlations were clarified so as to establish the simulation technology. At present, the system realizes 50kW and 40kWh/m{sup 3}. 1 ref., 8 figs.

  15. Effective use of active solar system on a residence; Jutakuyo taiyo enerugi akuteibu yuko riyo hoshiki ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Kamiya, Y. [Kanto Gakuin University, Yokohama (Japan)

    1999-11-25

    In this paper, reduction of primary energy consumed in a residence was calculated for the application of combination and hybrid systems of thermal solar energy and photovoltaic generation. The relation between the cost of each system and reduced energy was investigated. A combination system is more effective than a hybrid system for a residence in cost bases. At present time, the system of which area of panel less than 20 % of the floor area should be a solar system because of high cost of a PV system. And this percentage goes down to 5 % when the cost of PV system down to that of solar system in panel area bases. For a system larger than this, adding PV panel to a solar system, a combination system should be formed. (author)

  16. Research study on analysis/use technologies of genome information; Genome joho kaidoku riyo gijutsu no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For wide use of genome information in the industrial field, the required R and D was surveyed from the standpoints of biology and information science. To clarify the present state and issues of the international research on genome analysis, the genome map as well as sequence and function information are first surveyed. The current analysis/use technologies of genome information are analyzed, and the following are summarized: prediction and identification of gene regions in genome sequences, techniques for searching and selecting useful genes, and techniques for predicting the expression of gene functions and the gene-product structure and functions. It is recommended that R and D and data collection/interpretation necessary to clarify inter-gene interactions and information networks should be promoted by integrating Japanese advanced know-how and technologies. As examples of the impact of the research results on industry and society, the present state and future expected effect are summarized for medicines, diagnosis/analysis instruments, chemicals, foods, agriculture, fishery, animal husbandry, electronics, environment and information. 278 refs., 42 figs., 5 tabs.

  17. Generator cooling hydrogen purity improvement system using hydrogen absorbing alloy; Suiso kyuzo gokin riyo hatsudenkinai suiso jundo kojo system

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, H.; Kabutomori, T.; Wakisaka, Y. [Japan Steel Works, Ltd., Tokyo (Japan); Nishimura, Y.; Kogi, T.; Sato, J.; Haruki, N. [Kansai Electric Power Co. Inc., Osaka (Japan); Fujita, T. [Mitsubishi Electric Corp., Tokyo (Japan)

    1998-09-15

    Described herein is a system which uses a hydrogen-absorbing alloy to purify a hydrogen gas stream used as a coolant for power generator. Hydrogen in the stream containing impurities such as nitrogen can be selectively absorbed by sufficiently cooled hydrogen-absorbing alloy. Impurity gases concentrated in the alloy pores are released, and then the alloy is heated to release hydrogen. This purifies hydrogen to at least 99.99%. This system essentially consists of an hydrogen-absorbing unit, hot water production/supply system which circulates hot water of 80 to 90degC to release hydrogen out of the alloy, pretreatment unit, and temperature and pressure sensors. It is confirmed, by the test in which the system is connected to a commercial power generator of 600MW, that the system can be continuously operated to purify hydrogen to at least 99.9% for an extended period. 4 refs., 18 figs., 1 tab.

  18. Practical use technology of coal ash (Poz-O-Tec); Sekitanbai no yuko riyo gijutsu (POZ-O-TEC)

    Energy Technology Data Exchange (ETDEWEB)

    Konno, K. [Center for Coal Utilization, Japan, Tokyo (Japan); Saito, Y. [Mitsui Mining Co. Ltd., Tokyo (Japan); Nagaya, Y. [Mitsui Construction Co. Ltd., Tokyo (Japan)

    1996-09-01

    In order to utilize more effectively coal ash whose generation amount is increasing year after year, studies have been made on a technology to manufacture and utilize a high-strength substance solidified under normal temperature by utilizing hydration reaction of pozzolan system (Poz-O-Tec). The study works have been done as a subsidy operation of the Agency of Natural Resources and Energy, and were completed in fiscal 1995. Poz-O-Tec is a wet powder made of coal ash and stack gas desulfurization sludge (gypsum) added and mixed with lime and an adequate amount of water, which solidifies by hydration as pozzolan does. The same method as used for ordinary sands may be used as the basic application method. Because this is the material whose strength increases after construction, thickness of construction may be reduced smaller than in constructions using soils and sands. Test constructions of about sixty cases have been carried out to date, typically represented in use as a road bed material, banking, and a base material for water-barrier gutters. High-strength solid material which is stable under normal temperature may be obtained by adjusting calcium content. As a result of its effectiveness in practical use having been verified, a certificate of technological judgment has been issued for the material by the Civil Engineering Research Center. 3 refs., 11 figs., 2 tabs.

  19. Technology of CCS coal utilization (outline of large-size demonstration test for CCS); CCS tan riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Konno, K. [Center for Coal Utilization, Japan, Tokyo (Japan); Hironaka, H. [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

    1996-09-01

    The coal cartridge system (CCS) is a series of the total system, in which coal is processed centrally at a supply base for each unit of consumer areas, supplied as pulverized coal in bulk units, and coal ash after combustion is recovered and treated. The system is expected of advantages resulted from the centralized production, elimination of handling troubles, and cleanliness. Following a small scale demonstration test, a large demonstration test for practically usable scale has begun in 1990, and completed in fiscal 1995. This paper introduces the CCS and reports the result of the test. In the large demonstration test, a supply station (with manufacturing capability of 200,000 tons a year) was installed in the Aichi refinery of Idemitsu Kosan Co., Ltd., and systematization on quality design and system technologies has been carried out. Long-term continuous operation for five years was achieved (operation time of the supply facilities was about 19,000 hours) without a failure and accident, to which every elemental technology was evaluated highly, and convenience and reliability of the system was verified. 13 figs., 3 tabs.

  20. Incineration and its heat utilization for sludge and spent grains recycling. Beer kasu dassui odei shokyakunetsu no yuko riyo

    Energy Technology Data Exchange (ETDEWEB)

    Ogawa, T. (Asahi Breweries, Ltd., Tokyo (Japan))

    1993-06-01

    This paper introduces a case of effectively utilizing dehydrated sludge and spent grains as a boiler fuel, and industrial wastes from breweries to reduce the amount of wastes. These wastes show as high water content as 80% to 83%, but dried wastes are constituted of hydrocarbon, excepting ash. Especially beer spent grains have a calorific power of close to 5000 kcal/kg. The key point is how to blow off water efficiently (existence of a dehydration and drying process accompanies such advantages and disadvantages as facility simplification, necessity of auxiliary fuels, and generation of high-BOD water associated with beer lees dehydration). As a result of discussions and tests, a fluidized bed boiler (with a pressure of 14 kg/cm[sup 2] at a flow rate of 8.1 t/h) was adopted. Wastes to be burned dry up before they reach the floor of a fluidized furnace and are burned on the floor, and any unburned components are burned completely in a secondary combustion chamber. The boiler has been operating smoothly since the operation has started in 1989. An integrating comparison of various costs has resulted in annual economy of 81 million yen. 7 figs., 5 tabs.

  1. Studies of a dynamic type ice storage system using supercooled water; Kareikyakusui riyo dainamikku gata shochikunetsu shisutemu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ito, S.; Hashimoto, A.; Miura, N. [Kanagawa Inst. of Tech., Kanagawa (Japan); Ikemoto, Y.

    1999-11-25

    An ice storage system using supercooled water was constructed and the performance was tested. The system was consisted of a storage tank with the volume of 1.2 m{sup 3} in which slurry-ice was stared, a spiral double-tube heat exchanger 22 m long for making supercooled water by brine, a refrigerating machine of the rated capacity of 2.2 kW, reservoirs for cold and hot brine, heaters, and pumps. The system was able to be operated for more than 5 hours without freezing mostly if the degree of supercooling was less than about 2 degree C. The COPs based on the power of the refrigerating machine and system were about 1.3 and 0.7, respectively. (author)

  2. Investigation on development of advanced materials by solvothermal technique; Sorubo thermal hanno riyo senshin zairyo kaihatsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Solvothermal reaction is reaction under high temperature and high pressure, which is expected to fabricate new functional materials. In this study, the materials are classified into two fields, i.e., inorganic materials, metals and their composites and organic materials and their composites. The current status of R and D of production and processing technology in each field is surveyed and the prospect of it is discussed. For the inorganic materials, metals and their composites, it is explained that very fine metal oxide particles, complex oxides, single crystals, whiskers, compounds with layer structure, metastable compounds, ion conductors and catalysts with high ability could be produced only by controlling the solvothermal reactions in atomic order. For the organic materials and their composites, surveyed results of the solvothermal technique using non-aqueous solutions are mainly provided. The necessity of a national project for researches on the solvothermal reactions is proposed from the viewpoint of resource, environment and energy. 777 refs., 38 figs., 26 tabs.

  3. Application of a kinematic GPS to ship maneuvering trials; Soju seino shiken eno kinematic GPS no riyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Hirata, N.; Kose, K.; Takase, S.; Ito, R. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering; Nakamura, Y.; Terada, K.

    1997-09-04

    There has been a great progress in position measurement capability of well-known Global Positioning Systems (GPS) and the accuracy has been remarkably improved in the cm order, especially in a kinematic GPS (KGPS) which is based on the phase identification of GPS carrier waves. For the KGPS, interference measurement type differential GPS (DGPS) can be applied to moving ship. Accuracy of the KGPS has been examined. The sea trials of the coastal cargo ship have been conducted for grasping the performance improvement during trials by means of the KGPS. High accuracy in the measurements was evaluated about 2 cm horizontally and 5 cm vertically. The accuracy was occasionally degraded by the cycle slip generated with multi-pass and radio cutout. It is required to consider the setting position of antennas. Although the KGPS can determine the position in remarkably high accuracy, the direction can not be determined from a single measurement. It is required to determine the angle by combining the measurements. From the measurements during ship maneuvering trials using the KGPS, it was found that information required for evaluating the maneuvering performance, such as longitudinal and lateral velocities, turning angle velocity, and yawing angle, can be accurately determined. 5 refs., 8 figs., 5 tabs.

  4. Examination of actual utilization status on small scale wind power generation system; Kogata furyoku hatsuden system no riyo jittai chosa

    Energy Technology Data Exchange (ETDEWEB)

    Ito, K.; Matsui, T.; Inaoka, N. [Kansai Electric Power Co., Inc., Osaka (Japan); Miura, R. [Chiyoda Dames and Moore Co. Ltd., Tokyo (Japan)

    1994-12-01

    Although almost all of the wind mills for power generation with a small scale were self-manufactured in the past, since 10 and several years ago they have become to be regularly made as the industrial products. Even nowadays the small scale wind mills remaining in a market, or the small scale wind mills newly come to a market have adopted a contemporary advanced technology, and therefore in the utilization styles peculiar to the wind mills, an unique genre has been built. As for a scale of the wind mills, a system linking could also be considered, a scale of around 10 kw class was set up as a standard. As for total number of 98 units, a power generation scale could be classified into 41 kinds, from only 9 w as a small scale to 20 kw as a large scale. Now in this case 28 units of 1 kw - 5 kw class wind mill were most much collected. Many small scale wind mills actually used in Japan are often for the exhibits and the test/technological development. Also the locations where can not easily use a power from a power company can be frequently seen, however, like the huts and the light houses at a remote place. 4 refs., 9 figs., 2 tabs.

  5. Development of tensile test method for high-density coal under carbonization; Kojuten mitsudo sekitan no netsukan hippari shikenho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, A.; Ueki, M.; Aoki, H.; Miura, T. [Tohoku University, Sendai (Japan); Kato, K.; Fukuda, K. [Nippon Steel Corp., Tokyo (Japan)

    1998-05-01

    Since it is expected that the consumption of non-caking and slightly caking coals will increase and that particulates will have to be controlled with more severity, lumping in hot conditions is being studied as a next-generation technology for coke production. For the study of the augmentation of coke strength, the strength of the material has to be measured while it is in the semi-coke temperature zone. To fulfill the purpose, a method of tensile test is developed for densely packed coal in the carbonization process, which is applicable to non-caking and slightly caking coals. It is found that tensile strength and Young`s modulus increase in proportion to a rise in the ultimate carbonization temperature or in the heating rate. Attention is then paid to the maximum carbonization temperature and the heating rate, and a pyrolytic decomposition model is used for the calculation of the reaction rate, amount of hydrogen generated, porosity, amount of tar generated, and the rate of metaplast formation are calculated, and the results are used for the study of the mechanism of the appearance of strength . The amount of liquid tar increases as the amount of gaseous tar or the emission rate of metaplast increases. Graphitization (tightening by baking) advances with a rise in the reaction rate or in the amount of hydrogen generation. As for the macrostructure, coal particles are bonded together by liquid tar, and then the bondage is tightened by baking. 22 refs., 15 figs., 1 tab.

  6. Theoretical study on composition of gas produced by coal gasification; Sekitan gas ka de seiseisuru gas no sosei ni kansuru kosatsu (HYCOL data no doteki kaiseki)

    Energy Technology Data Exchange (ETDEWEB)

    Kaiho, M.; Yasuda, H.; Kobayashi, M.; Yamada, O.; Soneda, Y.; Makino, M. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    In relation to considerations on composition of gas produced by coal gasification, the HYCOL hydrogen generation process data were analyzed. From the fact that CO concentration (Y) decreases linearly with CO2 concentration (X), element balance of gasification of reacted coal was used to introduce a reaction analysis equation. The equation includes a term of oxygen excess {Delta}(amount of oxygen consumed for combustion of CO and H2 in excess of the theoretical amount), derived by subtracting the stoichiometric oxygen amount used to gasify coal into CO and H2 from the consumed oxygen amount. The {Delta} can be used as a reference to oxygen utilization efficiency. An equation for the {Delta} was introduced. Also introduced was a term for steam decomposition amount derived by subtracting the generated steam from the supplied steam. These terms may be used as a clue to permeate into the gasifying reaction process. This suggestion was discussed by applying the terms to gas composition value during operation. According to the HYCOL analysis, when a gasification furnace is operated at higher than the reference oxygen amount, coal supply variation is directly reflected to the combustion reaction, making the {Delta} distribution larger. In an inverse case, unreacted carbon remains in the furnace due to oxygen shortage, and shift reaction may occur more easily even if oxygen/coal supply ratio varies. 6 figs., 1 ref.

  7. Influence of catalytic activity and reaction conditions on the product distribution in coal liquefaction; Sekitan ekikayu no seiseibutsu bunpu ni taisuru shokubai kassei oyobi hanno joken no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Hasuo, H.; Sakanishi, K.; Mochida, I. [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study

    1996-10-28

    The NiMo sulfide supported on Ketjen Black (KB) was more effective and yielded lighter oil products containing light fractions with their boiling point below 300{degree}C during the two stage liquefaction combining low temperature and high temperature hydrogenation the conventional NiMo/alumina catalyst and FeS2 catalyst. Although the NiMo/alumina yielded increased oil products during the two stage liquefaction, the lighter oil fractions did not increase and the heavier fractions increased mainly. This suggests that the hydrogenation of aromatic rings and successive cleavage of the rings are necessary for producing the light oil, which is derived from the sufficient hydrogenation of aromatic rings using catalysts. For the two stage reaction with NiMo/KB catalyst, it was considered that sufficient hydrogen was directly transferred to coal molecules at the first stage of the low temperature reaction, which promoted the solubilization of coal and the successive hydrogenation at the high temperature reaction. Thus, high activity of the catalyst must be obtained. It is expected that further high quality distillates can be produced through the optimization of catalysts and solvents at the two stage reaction. 1 ref., 4 figs., 1 tab.

  8. Change in catalyst properties during coal liquefaction; Kokoritsu sekitan ekika shokubai no kaihatsu (Hanno no shinko ni tomonau shokubai seijo no henka). 1

    Energy Technology Data Exchange (ETDEWEB)

    Koyama, T.; Sato, K.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

    1996-10-28

    The purpose of this study is to prevent the deactivation of catalysts recycled in the 0.1 t/d bench scale unit (BSU). Catalysts recovered during reactions in the BSU and after reactions in the 5-liter autoclave were analyzed, to investigate the influences of the reaction condition on the property and activity of catalysts. Were used {gamma}-iron oxyhydroxide ({gamma}-FeOOH), {alpha}-iron oxyhydroxide ({alpha}-FeOOH), and natural pyrite (FeS2) as catalysts. At the S/Fe atomic ration of 1.2 under the BSU reaction condition, troilite was more easily formed from {gamma}-FeOOH compared with pyrite and {alpha}-FeOOH. As the reaction proceeded through the first, second, and third reactors, the crystal size increased, the pyrrhotite content decreased, and the troilite content increased. Deactivation due to the formation of troilite was irreversible. At the S/Fe of 3.0, however, both the formation of troilite and the crystal growth of pyrrhotite were not observed. It was found that the deactivation of catalysts can be remarkably suppressed. 5 refs., 6 figs., 1 tab.

  9. Characterization of interactions of coal surface with solvent by flow microcalorimetric measurement. 3; Netsuryo sokutei ni yoru sekitan hyomen to yozai tono sogo sayo no hyoka. 3

    Energy Technology Data Exchange (ETDEWEB)

    Wang, N.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan); Kotanigawa, T. [Japan International Corporation Agency, Tokyo (Japan)

    1996-10-28

    An investigation was given on the relationship between methanol adsorbing behavior of reformed coal surface and oxygen containing functional groups in coal. Akabira bituminous coal was air-oxidized or Yallourn brown coal was decarbonated in oil as a reformation treatment. Both of the treated and untreated coals showed an adsorption heat curve of the Langmuir type. The Akabira coal had its oxygen content and the adsorption heat increased as a result of the air oxidizing reformation treatment. The Yallourn coal had its oxygen content and adsorption heat decreased as a result decarbonation reformation treatment. Oxygen containing functional groups act as strong adsorption sites for methanol, and the maximum adsorption amount depends on oxygen content in the coals. Since the coal surface is non-uniform in terms of energy, methanol is adsorbed first into sites with higher molar adsorption heat, and then into lower sites sequentially. Therefore, distribution of the molar adsorption heat can be derived from the relationship between adsorption amount and adsorption heat by changing methanol adsorption amount. The distribution of molar adsorption heat becomes broader when the oxygen content is high, and narrower when low. 2 refs., 2 figs.

  10. Mechanism of pyrrhotite formation from ferric oxyhydroxide catalyst; Kokoritsu sekitan ekika shokubai no kaihatsu (Okishi suisankatetsu shokubai karano pyrrhotite seisei kyodo)

    Energy Technology Data Exchange (ETDEWEB)

    Tazawa, K.; Koyama, T.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

    1996-10-28

    It is thought that iron-based catalysts for coal liquefaction exercise their catalytic activity by forming pyrrhotite (Fe(1-x)S). However, there are still a lot of unknown problems remained concerning the formation and agglomeration behaviors of pyrrhotite. These make a difficulty for improving the activity of iron-based catalysts. In this study, sulfiding behaviors of {alpha}-iron oxyhydroxide ({alpha}-FeOOH) and {gamma}-iron oxyhydroxide ({gamma}-FeOOH) were investigated to reveal the formation and agglomeration behaviors of pyrrhotite. It was found that pyrrhotite was easily converted from ferric oxyhydroxide catalysts having large specific surface areas at the sulfiding temperature below 250{degree}C, and fine crystallites of pyrrhotite were formed at the initial stage of sulfiding. Crystal growth of pyrrhotite at the sulfiding temperature over 350{degree}C depended on the catalyst forms. It was also found that smaller crystallites of pyrrhotite were formed from {gamma}-FeOOH than from {alpha}-FeOOH and amorphous iron oxyhydroxide. 5 refs., 7 figs., 1 tab.

  11. Effect of heat treatment changes on swelling treatment of coal; Sekitan no bojun shori sayo ni oyobosu netsushori henka no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Satsuka, T.; Mashimo, K.; Wainai, T. [Nihon University, Tokyo (Japan). College of Science and Technology

    1996-10-28

    Discussions were given on effects of heat treatment at relatively low temperatures as a pretreatment for coal liquefaction on coal swelling and hydrogenolysis reaction. Taiheiyo coal was heated to 200{degree}C for one hour as a pretreatment. The attempted heating methods consisted of four steps of rapid heating (6.7{degree}C/min)quenching (20{degree}C/min), rapid heating/natural cooling (0.7{degree}C/min), heating (1.0{degree}C/min)/quenching, and heating/natural cooling. The swelling treatment was composed of adding methanol benzene into heat treated coal, and leaving it at room temperature for 24 hours. The hydrogenolysis was carried out by using a tetralin solvent and at an initial hydrogen pressure of 20 kg/cm{sup 2} and a temperature of 350{degree}C and for a time of one hour. Hydrogenolysis conversion in the heat treated coal was found lower than that of the original coal because of generation of liquefaction inactive components due to thermal polymerization. When the heat treated coal is swollen by using the solvent, gas yield from the hydrogenolysis reaction decreased due to gas suppression effect, and the conversion was lower than that of the original coal. Heat treatment suggests densification of the coal structure. Swollen coal shows no conspicuous difference in the heat treatment methods against the hydrogenolysis due to the swelling effect. 3 refs., 5 figs., 1 tab.

  12. Effect of burn-off on physical and chemical properties of coal char; Gas ka shinko ni tomonau sekitan char no tokusei henka

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, T.; Tamura, K.; Hashimoto, H.; Funaki, M.; Suzuki, T. [Kitami Institute of Technology, Hokkaido (Japan)

    1996-10-28

    For high-efficiency coal gasification, investigations were given on effect of coal chars with different conversion rates on coal gasification reactivity. In coal gasification, reactivity of char after pyrolysis governs the efficiency. The reference char conversion in CO2 gasification of coal (weight loss) changes linearly in the initial stage of the reaction, but the reactivity declines as the end point is approached. Char surface area is as large as 400 m{sup 2}/g in the initial stage with the conversion at 20%, but it decreases in the final stage. This phenomenon relates closely with changes in pore size and crystalline structure. Change in the Raman value R which shows incompleteness of char graphite structure and amorphous carbon ratio suggests that an active portion with high reactivity is oxidized preferentially, and a portion with low reactivity remains finally. Minerals in coal are known to accelerate the gasification. However, their catalytic effect is related with chemical forms, and complex as they may change into inactive sulfides and silicates under severe reaction conditions. Change in forms of calcium compounds may also be involved in decline of the reactivity in the latter stage. 8 refs., 4 figs.

  13. Proceedings of the papers of the 33rd Coal Science Conference (1996); Dai 33 kai sekitan kagaku kaigi happyo ronbunshu (1996)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-28

    This is a proceedings of the papers made public in the 33rd (fiscal 1996) Coal Science Conference held by the Japan Institute of Energy. The number of the papers included is 82. The processes such as coal liquefaction, coal gasification and pyrolysis are largely influenced by reaction of the carbon compound in coal. However, coal, which is different in reaction characteristics depending on its producing area, is a comprehensive compound. Therefore, the trial has been made for clarifying the molecular structure and skeleton. In the sense, the following papers are taken notice of: Suzuki and others` Estimation for origin of coals by biomaker analysis; Sugimoto and others` Change of unit skeletons during the artificial coalification; Hirado and others` Study on the correlation between chemical and mineral composition of coal ashes; Okawa and others` Coal structure construction system with construction knowledge and partial energy evaluation; Kanbayashi and others` Analysis of the relationship between coal properties and liquefaction characteristics by using the coal database.

  14. Coal structure construction system with construction knowledge and partial energy evaluation; Kochiku chishiki to bubunteki energy hyoka ni yoru sekitan bunshi kozo kochiku system

    Energy Technology Data Exchange (ETDEWEB)

    Okawa, T.; Sasai, T.; Komoda, N. [Osaka University, Osaka (Japan). Faculty of Engineering

    1996-10-28

    The computer aided coal structure construction system is proposed, and a computational construction example is presented. The coal structure construction engine of this system fabricates molecular structure by connecting fragments sequentially inputted through a user interface. The best structure candidate is determined using construction knowledge and partial energy evaluation every addition of one fragment, and this process is subsequently repeated. The structure evaluation engine analyzes the 3-D conformation candidate by molecular dynamics, and evaluates the conformation by determining the energy value of an optimum structure. As an example, this system was applied to construction of coal molecular structure based on the actual data of partial structure composed of 26 structures from 2l kinds of aromatic cluster structures, 27 bonds from 2 kinds of bridged bonds, and 16 groups from 2 kinds of terminal substitutional groups. As a result, this system could construct a superior structure according to expert knowledge from the viewpoint of energy. 6 refs., 5 figs., 2 tabs.

  15. Depolymerization of coal by O2 oxidation followed by acid hydrolysis; Sanso sanka-kasui bunkai ni yoru sekitan no teionkai jugo

    Energy Technology Data Exchange (ETDEWEB)

    Aizawa, S.; Hayashi, J.; Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1996-10-28

    With an objective to elucidate characteristics of oxygen addition to coal, and characteristics of solvent extraction by means of depolymerization, experiments were performed on oxygen oxidation and acid hydrolysis of brown coals. Coals used for the experiments are Morwell (MW), Yallourn (YL) , South Banko (SB) and Wyoming (WY) coals. Test samples were suspended in weak alkaline aqueous solution, and then oxygen was blown into them with pressure kept at atmospheric pressure. After a lapse of a predetermined time, the samples were cooled, and made as acidic as pH 1.3 in hydrochloric acid, followed by acid hydrolysis. Oxygen consumption increased with the reaction time, and with the MW coal, one mol oxygen reacted to 11 mols of coal. Spectral analysis on the YL and WY coal experiments revealed that aliphatic carbon combined with aromatic carbon or ether group has turned to peroxide, whose C-C or C-O bond was broken down as a result of acid hydrolysis of the peroxide, producing oxygen containing compounds. As a result of the depolymerization, the rate of extraction by using DMF, DMSO and methanol/THF mixed solvent increased to 90% or higher. Proportion of bond and cutting-off affects largely collapse of the cross-link structure. The carbon conversion to volatiles was at most 4%. 1 ref., 10 figs.

  16. Development of liquefaction process of coal and biomass in supercritical water; Chorinkaisui wo mochiita sekitan biomass doji ekika process no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nonaka, H.; Matsumura, Y.; Tsutsumi, A.; Yoshida, K. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Masuno, Y.; Inaba, A. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    Liquefaction of coal and biomass in supercritical water has been investigated, in which strong solubilization force of supercritical water against hydrocarbons is utilized. Free radicals are formed through the cleavage of covalent bonds in coal under the heating condition at around 400{degree}C during coal liquefaction. It is important to stabilize these unstable intermediate products by hydrogen transfer. On the other hand, hydrogen is not required for the liquefaction of biomass having higher H/C atomic ratio and oxygen content than those of coal. Co-liquefaction of coal and biomass was conducted using supercritical water, in which excess hydrogen from the liquefaction of biomass would be transferred to coal, resulting in the effective liquefaction of coal. Mixture of coal and cellulose was liquefied in supercritical water at 390{degree}C under the pressure of 25 MPa using a semi-continuous reactor, and the results were compared with those from the separate liquefaction of them. The co-liquefaction of coal and cellulose did not show any difference in the residue yield from the separate liquefaction of these, but led to the increased production of compounds with lower molecular weight. The liquefaction was completed in 15 minutes. 5 refs., 3 figs., 3 tabs.

  17. Report on the general course training of the fiscal 1996 coal engineer training program; 1996 nendo sekitan gijutsusha yosei jigyo ippan course kenshu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    The paper reported the general training of the fiscal 1996 coal engineer training program supported by NEDO. In Japan, where natural resource is poor, it is important to transfer from its petroleum dependence energy structure to the system for new energy development and dispersed energy supply. Coal resource is distributed widely in the world and is expected to spread in the future as a main substitute for petroleum. Worldwide attention is much paid to coal supply/demand and environmental problems, but the situation surrounding coal is not necessarily favorable. Under these conditions, Japan is a prominent coal importing country and is on the world-top level in terms of coal utilization technology. Japan has heavy responsibility and needs to play a leading role in adjusting and solving various problems on coal both domestically and internationally. Under the circumstances, 7 persons who are engaged in the coal related business and expected to be in future (3 from the mining relation and 4 from electric power comapanies) participated in the training this fiscal year and received the top-level training in Japan and overseas. 20 figs., 3 tabs.

  18. Basic survey for coal resources exploitation for Fiscal 1998. Coal GIS survey; 1998 nendo seitan shigeh kaihatsu kiso chosa. Sekitan GIS chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the construction of a coal mine assessment technology system, surveys are conducted on the current state and technology trends of resources-related GIS (geographical information system) in other countries. When one ponders over coal-rich areas to be newly explored and developed in one's study on the stable exploitation of coal abroad and its import to this country, what interests one gradually shifts from known superior large-scale coal mine areas to next-generation coal mine areas yet to be exploited. Accordingly, it is mandatory to build an assessment-oriented comprehensive technology system capable of promptly dealing with any changes in natural, geological conditions that may be presented by coal mines to be exploited. Although GIS is recognized as a useful means not only in the field of natural science but also in other fields whose data may be plotted on a map, its position is not yet established when it comes to coal resources. It is therefore necessary to promptly introduce GIS into the field of coal. In fiscal 1998, on-site surveys were conducted not only in Japan but also in the U.S., Canada, and Australia who are senior to Japan in terms of GIS application. Also, information was collected from literature and via Internet, surveys were conducted about the use of GIS in the field of earth science especially in the field of coal resources, and the state of the digital data utilizing setup indispensable for the proper operation of GIS was investigated. (NEDO)

  19. Fiscal 2000 coal engineer training program. Report on research study of general training course; 2000 nendo sekitan gijutsusha yosei jigyo. Ippan kosu kenshu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-11-22

    In connection with fiscal 2000 coal engineer training program, a research study of the general course was implemented with eight participants for the period from June 12 to November 22. In the field training, lectures were given at International Resources University by speakers from related companies, universities and laboratories, on such subjects as coal geology, coal mining technology, coal probing technology, marine cargo transportation, analysis, coal utilization technology, environmental preservation technology, overseas coal mine development project, and foreign coal situations. Also, in the seminar, on-the-spot training was conducted at such places as Taiheiyo Tanko Kushiro mining station, Nippon Kokan KK Keihin ironworks, Electric Power Development Co., Isogo thermal power station, Idemitsu Kosan Co., coal laboratory, MITI Agency of Natural Resources and Energy. In the overseas training, research study in China was carried out during the period from July 2 to July 7 while research study in the U.S./Canada and Australia/Indonesia were conducted separately by two groups through 35 day trip from Oct 7 to November 10. The major places for visit were energy-related organizations, coal mining companies, railway companies, coal handling harbors, coal thermal power stations, coal analysis companies, etc.. (NEDO)

  20. Coal engineer training project for fiscal 1999. Report on general course training; 1999 nendo sekitan gijutsusha yosei jigyo. Ippan course kenshu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-19

    This report was made on the general course training in the coal engineer training project implemented in fiscal 1999. The training was conducted from June 7 through November 19 with total 7 participating trainees from an electric power company, mining company, etc.. In the training, the lectures were given by speakers from domestic coal related companies, universities, laboratories and the like at the University of International Resources, a foundation, for about three weeks. An English training was carried out by three instructors at the same University for about eleven weeks with the purpose of acquiring the linguistic ability required for overseas coal development. The joint seminar was conducted in Tokyo by inviting lecturers, two from Australia and one each from Canada and Indonesia. The training by visiting the domestic coal related companies was such that the overseas lecturers and trainees visited Matsushima Mining Co., the Electric Power Development Company, NKK Corp and others. The overseas study and training were performed on a 35 day schedule by visiting energy-related institutions, mining companies, railway companies, coal loading/unloading harbors, and thermal power stations in Canada, the U.S., and Australia. (NEDO)

  1. Japan`s Sunshine Project. 1991 annual summary of coal liquefaction and gasification; 1991 nendo sunshine keikaku seika hokokusho gaiyoshu. Sekitan no ekika gas ka

    Energy Technology Data Exchange (ETDEWEB)

    1992-07-01

    Out of the research and development on the 1991 Sunshine Project, the results of coal liquefaction/gasification are reported. The basic research of coal liquefaction/gasification is conducted. The research plan for a 150 ton/day scale pilot plant (PP) is worked out for the development of bituminous coal liquefaction technology by NEDOL process. Data of PSU (Process Support Units) operation, especially, are studied. Concerning the data obtained through dismantling of the 50 ton/day PP in Australia which uses Australian Victoria coal due to completion of its operation and also obtained from its support research, they are reflected in the design of a demonstration plant, and the results are arranged for study. Research and development on refining technology of coal-derived liquid such as Illinois coal liquid and on application technology of its products are made. For the development of coal-use hydrogen production technology, conducted is the research of a high temperature gasification PP by entrained flow bed process which is the core of the coal gasification technology. Elementary study with a 2 ton/day furnace is made for the development of the entrained flow bed coal gasification combined cycle power generation system. Also conducted are PP construction, adjusting operation and the overall research operation.

  2. Development of the super coke oven for productivity and environment enhancement toward the 21st century (SCOPE 21); Sekitan kodo tenkan cokes seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sugiyama, T. [Center for Coal Utilization, Japan, Tokyo (Japan); Nakashima, Y.; Nishioka, K.; Otsuka, J. [The Japan Iron and Steel Federation, Tokyo (Japan)

    1996-09-01

    Serious shortage is predicted on cokes for blast furnaces in the first half of the 21st century. In order to deal flexibly with the fluid world market in the future, it is necessary to have a technology developed, by which coals from coking coal to non-coking dust coal can be used. The Japan Iron and Steel Federation and the Center for Coal Utilization, Japan are working on research and development of a new process with enhanced environmentality and economy (SCOPE 21) as a coke manufacturing process to respond to the requirements arisen from the above situation. The process is assessed basing on basic technological seeds such as rapid coal heating and high-speed carbonization and reformation of middle to low temperature cokes. The organizations are moving forward an eight-year development program which has started in fiscal 1994. This paper reports the summary of the development, and results of investigations and researches performed during fiscals 1994 and 1995. Rapid heating tests, middle to low temperature coke reformation tests, and tests for plug transportation of high-temperature coal have been performed. It has been verified, for example, that rapid coal heating can improve coke strength. The development work is being promoted toward grain size distribution and upscaling problems. 5 refs., 16 figs., 2 tabs.

  3. Japan`s New Sunshine Project. 1996 Annual Summary of Coal Liquefaction and Gasification; 1996 nendo new sunshine keikaku seika hokokusho gaiyoshu. Sekitan no ekika gasuka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    In reference to the results of the research and development under the fiscal 1996 New Sunshine Project, a report was summed up on coal liquefaction and coal gasification. As to the R and D of coal liquefaction technology, researches were conducted on liquefaction characteristics and engineering properties by coal kind, catalysts for coal liquefaction, liquefaction reaction of coal and reformation utilization of the liquefied products, liquefaction reaction mechanism and coking mechanism, solubility of coal in solvent and catalytic reaction mechanism, solvent reaction mechanism by hydrogen donor solvent, etc. Concerning the R and D of coal gasification technology, made were the basic study of eco-technology adaptable gasification technology and the study of coal gasification enhancing technology. Further, as to the development of bituminous coal liquefaction technology, carried out were the study in pilot plants and the support study of pilot plants. Additionally, R and D were done of the basic technology of coal liquefaction such as upgrading technology and environmentally acceptable coal liquefaction technology, and of coal hydrogasification technology. 3 refs., 81 figs., 25 tabs.

  4. Simulation modeling of fluidized bed coal gasifier for new topping cycle system; Toppingu saikuru ryudoso sekitan gasu karo no shimyureshon moderu

    Energy Technology Data Exchange (ETDEWEB)

    Iin, G.; Yamazaki, R.; Mori, S.; Fujima, Y. [Nagoya Univ. (Japan)

    1998-01-01

    A new topping cycle coal power generation process has been developed as a Japanese national project for a high efficiency power generation process. This process consists of a pressurized bubbling fluidized-bed coal gasifier and a pressurized bubbling fluidized-bed combustor which combined in series. To evaluate the performance and to determine specification and operation parameters of this process, it is extremely important to analyze the behavior and the performance of the system by a reasonable simulation model. A simulation model of this new process is developed in this paper. It is demonstrated by calculating results from this model that the carbon conversion in the gasifier, the composition and the heating value of the produced gas are strongly dependent on operating conditions. Heat recovery by steam in the combustor is controlled by the coal feed rate. 4 refs., 8 figs., 2 tabs.

  5. Effect of properties of iron compounds on the catalytic activity in direct coal liquefaction; Tetsu kagobutsu no keitai to sekitan ekika kassei

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, T.; Tazawa, K. [Mitsubishi Chemical Corp., Tokyo (Japan); Shimasaki, K. [Kobe Steel Ltd. (Japan)

    1998-08-20

    When considering merchandising scale of the coal liquefaction process, it is a preliminary condition that metal used for its catalyst is rich in resource volume, cheap in production cost, without pollution, and so forth, and application of cheap iron ore and ferrous compounds to disposable catalyst is desired. As liquefaction activity of the iron ore was hitherto improved by its micro crushing, its mechanical crush had a limit of about 2 {mu}m in mean particle diameter. However, together with recent crushing technique, crushers with high performance were developed, and then micro crushing by sub-micron became possible industri8ally even for iron ore. In this study, three kinds of Australian iron ores such as limonite of ferric hydroxide type iron ore, pyrite of ferrous sulfide type, and hematite of ferric oxide type were micro crushed to examine coal liquefaction activity and hydrogenation reaction activity of 1-methyl naphthalene (1-MN) and also relationship between properties and activity of catalyst for the latter before and after reaction. 11 refs., 8 figs., 5 tabs.

  6. Report on the 1997 Coal Engineer Training Program General Course Training; 1997 nendo sekitan gijutsusha yosei jigyo ippan course kenshu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    The paper reported training in the fiscal 1997 coal engineer training course. The training was made in a period from June 9 to November 12 in terms of actual training, English training, joint seminar, visits to the related facilities in Japan, overseas training, etc. for 10 engineers from mining companies, oil companies and electric power companies. In the actual training, the following lectures were given at International Resource University in Akita prefecture: coal exploration technology, coal situation of Australia, physical/chemical characteristics of coal and the application, coal preparation technology, coal situation in India, coal situation in the U.S., trend of general coal demand, coal situation in China, coal mining technology, actual surface mining technology, coal situation in Canada, commercial English, trend of raw coal demand, coal geology, environmental protection technology related to coal utilization, etc. Overseas training, which was divided into an Australia group and a Canada/America group, was conducted for about a month. Training in Indonesia was canceled because of a large scale forest fire which broke out immediately before the start. 88 figs., 52 tabs.

  7. Guarantee of property right in open access systems. Legal study of property right of electric utilities and expropriation; Open access ni okeru zaisanken no hosho. Denki jigyo ni okeru zaisanken to shuyo ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Maruyama, M. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-03-01

    A study has been made about the relationship between open access, which has now become an important element of the electric utilities renovation efforts in the U.S. and Europe, and property right. The meaning of open access is to guarantee free access to suppliers by securing fair competition between them through separation of the vertical integration in power transmission and opening the transmission network to final customers. In case of Japan, the U.S., and Germany where private sector suppliers run electric utilities, however, a need arises to consider the property right that such suppliers enjoy as guaranteed by their Constitutions. The outcomes of discussions made in Germany and the State of California were complied, and some conclusions were reached. It constitutes an infringement of their property right for the authorities to order them to allow open access without compensation. In case the authorities use expropriation for the same purpose, they have to make it known clearly that the separation and opening is to the benefit of the public and must compensate fully for their action. There is no problem in giving the authorities the power to force the electric utilities to sign a wheeling contract in case the latter unlawfully rejects to sign one proposed by a wheeling-requesting party. 24 refs., 3 figs., 4 tabs.

  8. Looking for mine of the petroleum in China, especially, looking for mine activities in the foreign enterprise; Chukajinminkyowokoku ni okeru sekiyu no tanko. Tokuni gaikokukigyo ni okeru tanko katsudo

    Energy Technology Data Exchange (ETDEWEB)

    Hirai, Makoto

    1999-01-01

    Modern petroleum industry after the Chinese establishment (1950) rose mainly by the Russian cooperation, and main discovery such as oil field 1959 was made as to the discovery in 1955 oil field. After that, that activities range was limited to middle Kunisaki department land stage by a master though looking for mine which is characteristic of China, development were made by Russian withdrawal and there was discovery such as a task hill oil field in the victory oil field and 1964 big port oil field for 1962 and for 1976. (NEDO)

  9. Study on the optimal control of the ground thermal storage system in the greenhouse. Part 4; Onshitsu ni okeru taiyo energy dochu chikunetsu system ni okeru saiteki seigyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, M. [Sanko Air Conditioning Co. Ltd., Osaka (Japan); Nakahara, N. [Kanagawa University, Yokohama (Japan)

    1996-10-27

    Three types of weight in both energy saving and optimum room temperature environment were changed to obtain the optimal control solution of the ground thermal storage system in a greenhouse. The relation diagram between the optimal solution of a performance function, and the state constraints and control function constraints was created in consideration of the energy term in a control function value area and the room temperature environment. As a result, the whole image of the performance function could be grasped in consideration of the energy term with inequality constraints and the room temperature environmental term in this study. The rate of a weighting factor in the performance function significantly influences the optimal solution. The influence on the optimal solution also changes when the optimal room temperature schedule differs. The influence that three types of rising algorithm exert on the convergence and converging speed was investigated. Superiority or inferiority occurs according to the space properties of a performance function. A zigzag method is most disadvantageous. The constraints can be converged to the optimal solution using an SUMT outer point method irrespective of the initial value. 6 refs., 6 figs., 4 tabs.

  10. 3D seismic survey in Honjo, Akita. Problems and struggles in acquisition and processing; Akitaken Honjo koku ni okeru sanjigen jishin tansa. Genba sagyo to data shori ni okeru mondaiten

    Energy Technology Data Exchange (ETDEWEB)

    Imahori, S.; Kotera, Y.; Nakanishi, T. [Japan Energy Development Co. Ltd., Tokyo (Japan)

    1997-05-27

    Honjo mining area where investigations are conducted is hilly and has a complicated terrain with gas pipes buried in the ground just under the access road disabling the proper positioning of shock-generating large excavators or vibrators. Auger`s shallow hole shooting method is used in this survey to execute blastings at 639 points. In this method using charge depths of 4m, different from the conventional method using deeper charge depths (20-25m), surface waves prevail in the shot records giving rise to a new problem of removing them in the stage of data processing. The 2D filter that is a powerful tool in 2D data processing is not available in a 3D-survey where the tracing intervals are irregular in the shot records. In the effort of this time, a window length as a parameter in the direction of time is specified, and the F-X dip filtering method is employed in which any event that linearly continues beyond a certain number of traces in the said window is eliminated as a linear noise. It is recommended that the weighting function be changed in the direction of space since surface wave velocities are different at different locations. 1 fig., 1 tab.

  11. Waste gas treatment technology at steelmaking plants. Seitetsu setsubi ni okeru hai gas shori gijutsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, M.; Shimizu, K.; Deshimaru, K.; Watari, S. (Nihon Univ., Narashino, Chiba (Japan). Coll. of Industrial Technology)

    1992-11-30

    A variety of furnaces are employed for steelmaking. The waste gases from these furnaces are used as fuel gases or flared to the atmosphere. For the enhancement of energy efficiency at these plants and the improvement of environment, it is essential to remove the impurities contained in the waste gases, such as soot, dust, NOx and SOx with high efficiency at the lowest possible cost. In coke oven and sintering furnace, soot and dust consisting of sulphuric element, cyanogenic element and fume of alkali metals as main constituents are the subject of treatment, because these elements were contained in the raw materials. And, in blast furnace and LD converter, soot and dust are the subject of treatment because the materials have already been treated under high-temperature and the waste gases contain little chemical impurities consequently. On the other hand, in various combustion furnaces, purified by-product gases, such as the above mentioned BFG (blast furnace gas), LDG (LD converter gas) and COG (coke oven gas), etc., are used frequently and NOx generated by the high-temperature combustion is often the subject of treatment. In this report, the waste gas treatment technology developed by Nippon Steel Corporation for these various furnaces was described. 10 figs., 2 tabs.

  12. Prevention countermeasure for breeding of iron bacteria in ion-exchanged water. Junsui ni okeru tetsu bakuteria hassei boshi taisaku

    Energy Technology Data Exchange (ETDEWEB)

    Yoshimura, S. (Nippon Steel Corp., Tokyo (Japan))

    1994-06-01

    The wear troubles of the water-supplying pump as well as water-supplying control valve due to the blocking-up of the strainer caused by the abnormal breeding of iron bacteria in ion-exchanged water have been occurring frequently since several years before in Oita Manufactory of Nippon Steel Corporation. The strainer provided in front of the pumps for supplying the water to each users are blocked up by the iron bacteria bred abnormally in the tanks of ion-exchanged water. Consequently, the cavitation phenomenon of water-supplying pump happens and the inside wear occurs. It is revealed by the results of the examination on the prevention countermeasure for breeding of iron bacteria carried out by the present authors that the destruction and the extinction of the cells are brought about by the concentrated electrification of the iron bacteria due to the electrification in the ion-exchanged water. In this paper, the principles, progress of study and development, the results of the practical tests in respect of prevention countermeasure for breeding of iron bacteria in ion-exchanged water by turning on electricity are described. The conventional means of frequency transformation are used in the experiment, and the betterment such as the increase of capacity of condenser is added because of the high electricity-resistance of ion-exchanged water. 13 figs., 1 tab.

  13. Deep sedimentary structure model beneath the Osaka plain; Osaka heiya ni okeru shinbu chika kozo no model ka

    Energy Technology Data Exchange (ETDEWEB)

    Miyakoshi, K.; Kagawa, T.; Echigo, T. [Osaka Soil Test, Osaka (Japan)

    1997-05-27

    Restructuring was carried out on a sedimentary basin structure model of the Osaka plain including Osaka Bay by using newly obtained underground structural data. After the Hygoken-nanbu Earthquake of 1995, a large number of underground structure investigations have been performed in Osaka Bay and urban areas of Kobe and Osaka. However, very few surveys have been done in areas peripheral to Osaka Prefecture, such as the Ikoma area. Therefore, an attempt has been made to increase the number of measuring points to acquire underground structural data of these areas. Estimation of basic rock depths has utilized the dominant cycles in H/V spectra obtained from micro vibration survey, and good correlation of the base rock depths derived by a refraction exploration and a deep-bed boring investigation. With regard to bed division and P- and S- wave velocities in sedimentary beds in the Osaka sedimentary basin, an underground structure model was prepared, which was divided into four beds according to the refraction exploration and the micro vibration investigation. Data obtained by using this model agreed well with depth data acquired from physical exploration and other types of investigations. However, no good agreement was recognized in the data for such areas where the basic depth changes abruptly as the Rokko fault and the Osaka bay fault. 6 refs., 8 figs., 2 tabs.

  14. Magnetic susceptibility measurements in Yellowstone National Park, USA; Beikoku Yellowstone kokuritsu koen ni okeru genchi jikaritsu sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Okuma, S. [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    For the purpose of interpreting data of the aeromagnetic anomalies in Yellowstone National Park in the U.S.A., in-situ magnetization intensity measurements have been carried out in 1994 and 1995 on geological outcrops of rocks in that area. Comparisons and discussions were given on the measurement results, and existing rock magnetic data and aeromagnetic anomaly data available for the area. Outside the Yellowstone caldera, part of granitic gneisses among the Precambrian granitic gneisses and crystalline schists distributed to the north has an abnormally high magnetization intensity of 1 {times} 10 {sup -2} SI. This could be a powerful anomaly source for the high magnetic anomaly in this area. Paleogene volcanic rocks distributed widely in the eastern part of the park also have magnetization intensity as high as 1 {times} 10 {sup -2} SI or higher, which are also thought a powerful anomaly source in this area. Part of Pleistocene basalts which are exposed partially in the western part of the park has also very high magnetization intensity at 1 {times} 10 {sup -2} SI or higher. This suggests correlation with the magnetic anomaly in the east-west direction distributed in this area. Quaternary rhyolites are more magnetic than Quaternary welded tuffs, which should give greater effects to the magnetic anomaly. 10 refs., 5 figs.

  15. Examination of poisonous gas in Matsumoto city, Nagano Pref.; Matsumotoshi ni okeru yudoku gas chudoku jiko eno taio

    Energy Technology Data Exchange (ETDEWEB)

    Furuhata, A. [Nagano Research Inst. for Health and Pollution, Nagano (Japan)

    1996-02-10

    This report explains how the Sanitation and Pollution Laboratory of Nagano Prefecture came to isolate sarin and describes some examples of information gathering efforts which played a very important role in the sarin isolating process. The Matsumoto sarin incident took place late at night of June 27, 1994. The laboratory acting upon a request of the prefectural pollution control section completed its specimen collecting in the afternoon of June 28. In its efforts to search for the casualty-causing substance, the laboratory gathered information from the National Institute of Hygienic Sciences, Japan Poison Information Center, JICST, Matsumoto Health Center, and Professor Naito of the Tsukuba University. Next, the analysis/retrieval team started collecting data from the GC-FPD and GC-MS. The peak in the curve pointed to sarin, and this also made it clear that the substance was neither soman nor tabun. A question remained unanswered as to why sarin, a nerve gas which is a weapon of war, existed in a peaceful castle town of Matsumoto. The greatest difficulty in the sarin isolating process came from the lack of the standard substance to which sarin was to be referred to. Sarin was determined to be the responsible substance only after a general judgement based on the results of comparison with the retention indexes, analysis using the GC-MS (EI) and then GC-MS (CI), and experiments using Japanese cyprinodont. 8 refs., 1 tab.

  16. Change of unit skeletons during an artificial coalification; Jinko sekitanka katei ni okeru tan`i kokkaku kozo no henka

    Energy Technology Data Exchange (ETDEWEB)

    Sugimoto, Y.; Miki, Y.; Hayamizu, K. [National Institute of Materials and Chemical Research, Tsukuba (Japan); Okada, K. [Coal Mining Research Center, Tokyo (Japan); Suzuki, Y. [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-28

    In order to obtain knowledge about formation and growth of condensed ring structure in a coalification process, discussions were given on product skeleton structure by using hydrogenation and hydrocracking of heated cellulose. In underwater heating of cellulose, reaction of dehydration has occurred at 200{degree}C or lower, that of decarbonation at 250{degree}C or higher, and that of demethanizing at 300{degree}C, resulting in production of a dark-brown coal-like substance. The substance has lower H/C value and higher O/C value than coal. As the underwater heating temperature rises, the hydrogenation reactivity of the heated substance decreases, and so does the ratio of conversion into toluene solubles. These phenomena are related to strength of cross-linking bond between unit skeleton structures. A substance heated at an underwater heating temperature of 200{degree}C turns toluene-soluble almost completely even during the hydrogenation reaction (350{degree}C for 2 hours), but the soluble product decreases at underwater heating temperatures of 250 and 300{degree}C. However, soluble product of more than 90% was obtained when hydrocracking (at 425{degree}C for one hour) was performed. The toluene-soluble product in the heated substance is only 50% when the underwater heating temperature reaches 350{degree}C even if the hydrocracking is carried out. 3 refs., 5 figs.

  17. Hydrogenolysis reactions characteristics of deashed coal under low temperature; Teionka ni okeru dakkai shoritan no suisoka bunkai hanno tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Owada, T.; Mashimo, K.; Wainai, T. [Nihon University, Tokyo (Japan). College of Science and Technology

    1996-10-28

    In relation to coal liquefaction, the effect of inorganic minerals on liquefaction reactivity and the effect of hydrofluoric acid (HF) treatment on organic molecular structure of coals were studied by demineralization of low-rank coals in HCl or HF solution. In experiment, Taiheiyo coal specimen was deashed in HCl solution at 25-70{degree}C for 6 hours while agitating, and in addition, deashed in HF solution. Hydrogenolysis of the deashed coal specimen was conducted using tetralin or methylnaphthalene as solvent under initial hydrogen pressure of 1.96MPa at reaction temperature of 693K for 60min. The experimental results are as follows. The ash content of Taiheiyo coal hardly offers catalysis in hydrogenolysis reaction. Carboxyl group increases in demineralization of coal because of breakage of bridged bonds. Organic structure of coal changes by demineralization in dense HF solution. Change in organic structure of coal by demineralization in dense HF solution is dependent on treatment temperature. 2 refs., 4 figs., 1 tab.

  18. Decay of weak pressure waves in a low pressure tube; Teiatsu kannai ni okeru bisho atsuryokuha no gensui

    Energy Technology Data Exchange (ETDEWEB)

    Takiya, T.; Terada, Y.; Komura, A. [Hitachi Zosen Corp., Osaka (Japan); Higashino, F.; Abe, H. [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan). Faculty of Technology; Abe, M. [National Lab. for High Energy Physics, Tsukuba (Japan)

    1996-04-25

    The characteristics of pressure wave propagation in a vacuum tube have been investigated experimentally from the viewpoint of vacuum protection in the beam lines of a synchrotrons radiation facility. Baffle plates having a single orifice of 5, 10 or 15 mm in diameter were installed in shock tubes 5 m in length, and 36.6 or 68.8 mm in diameter, in order to show the pressure wave or shock wave propagation as a model for the beam line. To evaluate the decay of pressure waves pressure changes with time at several locations along the side wall as well as at the end wall of the tube were measured. The results show that the effect of the orifices on pressure wave propagation and its decay is significant. The present investigation may contribute to the design and construction of high energy synchrotrons radiation facilities with long beam lines. 11 refs., 9 figs., 2 tabs.

  19. Ebara`s environmental management system and ISO14001; Ebara ni okeru kankyo management system to ISO14001

    Energy Technology Data Exchange (ETDEWEB)

    Umeda, M. [Ebara Corp., Tokyo (Japan)

    1999-04-20

    Situations encompassing environmental problems are recently undergoing drastic changes on a worldwide scale. The number of business locations which have been certified as ISO14001 sites in Japan has exceeded 1,392 by the end of November 1998, a surge which is expected to outrun that experienced regarding ISO9000 sites. In December 1997, the United Nations Frame Work Convention on Climate Change (COP3) was held in Kyoto, Japan to discuss the prevention of the global warming effect. The following discusses how Ebara`s environmental management system is related to problems and solutions discussed in this symposium. Discussion is also made on the impact of environmental management on enthusiastically carried out environment-related businesses. Finally, discussion is made on Ebara`s future environmental management system, i.e. as an outcome of past and current efforts in Ebara`s continuous improvement on environmental management, including Ebara`s 5 areas which have attained the ISO14001 standard. (author)

  20. Feasibility study of various geophysical methods at the Nojima fault; Nojima danso ni okeru kakushu butsuri tansaho no tekiyo jikken

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, T.; Nozaki, K.; Shima, H.; Yamane, M.; Igarashi, T. [OYO Corp., Tokyo (Japan)

    1996-05-01

    This paper reports a feasibility study of various geophysical methods at the Nojima fault. A shallow bed investigation (to a depth of several ten meters) was performed at the Nojima-Hirabayashi area, a very shallow bed investigation (to a depth of several meters), a shallow bed investigation and a medium depth bed investigation (to a depth of several hundred meters) at the Kokura area, and a very shallow bed investigation at the Nashimoto area. Combinations of two to four investigation methods were used according to the objectives and depths of the investigations at each area. The combinations were selected from the following methods: seismic investigations (P-wave reflection and N-wave reflection methods), electric investigation using the IP image method, electromagnetic investigation using the VLF method, underground radar investigation, micro-gravity investigation, and gravity investigation. The result may be summarized as follows: in places where a fault forms a boundary between base rocks and a sedimentation bed, it was possible to identify clearly position of the fault, and estimate inclination angles and vertical shift; and during the medium depth investigation at the Kokura area, identification was made on a geological structure (deformation of a sedimentation bed above the base bed) which is important in verifying the nature of an active fault. 2 refs., 5 figs., 1 tab.

  1. Using of the geophysical methods to an investigation in city; Toshi ni okeru butsuri tansaho no tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Sato, S. [Oyo Corp., Tokyo (Japan)

    1995-02-10

    Some of the exploration methods are taken up out of the geophysical methods, which have made drastic change by technological advancement, to discuss their technological development and application in cities. The elastic wave exploration is classified into the refraction method which uses refracted waves and the reflection method which utilizes reflected waves. Shallow reflection method allows visual observation of the complex underground structure, and is an excellent exploration method which provides highly accurate data. There are many types in the electrical exploration. New exploration methods have been developed as a result of improvement in the computer performance, advancement in the technology of numerical analysis, and improvement in the performance of exploration equipment, and they are being applied to the electrical exploration in many fields including tunnel and dam construction works. Geotomography is an application of the technology of medical tomography to ground exploration. Underground radar method is a method of investigating the ground structure by radiating electromagnetic waves from the ground surface in similar way to that of the reflection method and capturing the reflected waves from underground. 8 refs., 7 figs.

  2. Global Environment, human activity, and recycling of resources. Chikyu kankyo to ningen katsudo ni okeru shigen recycling

    Energy Technology Data Exchange (ETDEWEB)

    Nakahiro, Y.; Wakamatsu, T. (Kyoto Univ., Kyoto (Japan). Faculty of Engineering)

    1991-04-18

    Discussion is made on the recycling of resources which is one the very important problems for the global environment and human activity. In consideration of the limited natural resources and utilization by the human race of the resources for long, recycling of resources'' for saving resources is extremely important. The scale of the waste treatment industry in Japan is estimated to be between 4 to 5 trillion yen which exceeds 1% of the GNP with the trend of increase year by year, and the industrial waste treatment industry is taking root in Japan. Recycling'' can be grouped in three methods, i.e. recovery of materials, conversion of materials, and conversion of energy. The primary object of recycling is to spare resources and save energy. Recycling is of deep significance from the viewpoint of energy saving. There is a big merit in the conservation of dumping sites. Making best use of the useful secondary resources in the wastes is directly connected with the solution to the problems of prolongation of resources'' and conservation of global environment'' with which the human race is now confronted. 7 refs., 7 figs., 2 tabs.

  3. Education for hydraulics and pneumatics in Nara National College of Technology; Nara Kogyo Koto Senmon Gakko ni okeru yukuatsu kyoiku

    Energy Technology Data Exchange (ETDEWEB)

    Hayakawa, Y. [Nara Technical Coll., Nara (Japan)

    2000-03-15

    In the electronic control engineering course, basic knowledge is taught for mechanics, electronics/electricity, control, robotics, information processing, etc., with the purpose of bringing up practical mechatronics engineers, and then, training is conducted so that the students are able to deal with these subjects comprehensively. In the subject of hydraulics and pneumatics for the special course, a lecture on hydraulic and pneumatic control is given in the second year, where structures of hydraulic and pneumatic actuators are explained as well as the principle of operation and the control method. As the related experiment, measurement of liquid viscosity coefficient and flow measurement by a Venturi tube are carried out in the fourth year of the regular course. In addition, carried out in the fifth year are the measurement of stress by trailing velocity distribution of an object and the measurement of pressure distribution around a column. As a subject for graduation theses, a mobile carrier for welfare nursing is being developed using a pneumatic actuator. Development of a suitable actuator is also being developed simultaneously. In the education of electronic control engineering, it is essential to give the students understanding of hydraulic and pneumatic actuator control centering on the role of mechatronics. (NEDO)

  4. Water quality and water pollution sources in Poyang lake, China; Poyang ko ni okeru suishitsu chosa to odakugen kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Ito, M. [Shin-Nippon Meteorological and Oceanographical Consultant Co. Ltd., Tokyo (Japan)

    1996-01-10

    This paper summarizes the current status of water quality and pollution sources in Poyang Lake in China. The lake is located in Chianghsi Province of China, and a largest fresh water lake in China that flows out into the Yangtze river. The basin is surrounded by mountains on three sides and faces the Yangtze on one side, whereas the plains formed by the lake and the rivers flowing in extends in the center of the basin. The plains around the lake has the city of Nanchang, the capital of the province, the city of Jiujiang (both cities have a population of about 4 million, respectively), and four other cities with a size of one million people including Jingdezhen. Water supply system in the basin is used in a 37% area of the urban areas, and no sewage facilities of whatsoever are available as of 1991. The lake has COD of about 3 mg{times}1/l. No severe pollution by organic matters is seen. While the T-P concentration is at a high level, PO4-P is low. Majority of phosphorus flowing into the basin exists in the form trapped in soil particles. In order to maintain the current water quality in the future, waste water treatment is required in the basin. Construction of an oxidation pond in the vast land exposed during the drought period is a measure that can be tackled relatively easily. 1 fig., 4 tabs.

  5. Measurement improvements of heat flux probes for internal combustion engine; Nainen kikan ni okeru netsuryusokukei no kaihatsu to kento

    Energy Technology Data Exchange (ETDEWEB)

    Tajima, H.; Tasaka, H. [Miyazaki University, Miyazaki (Japan)

    1997-10-01

    In heat flux measurement in engines, material properties of a heat flux probe and numerical prediction of those influence have been discussed rather than practical measurement accuracy. This study featured the process for the quantitative examination of heat flux probes. Although the process required direct comparison among all the probes and additional measurements in a constant volume bomb, precision of heat flux measurement was greatly improved so that the essential characteristics of heat transfer in engines can be detected. 9 refs., 8 figs., 1 tab.

  6. Simulation of speed control in acceleration mode of a heavy duty vehicle; Ogatasha no kasokuji ni okeru shasoku seigyo simulation

    Energy Technology Data Exchange (ETDEWEB)

    Endo, S.; Ukawa, H. [Isuzu Advanced Engineering Center, Ltd., Tokyo (Japan); Sanada, K.; Kitagawa, A. [Tokyo Institute of Technology, Tokyo (Japan)

    1997-10-01

    A control law of speed of a heavy duty vehicle in acceleration mode is presented, which is an extended version of a control law in deceleration mode proposed by the authors. The control law is based on constant acceleration strategy. Using the control law, target velocity and target distance can be performed. Both control laws for acceleration and deceleration mode can be represented by a unified mathematical formulae. Some simulation results are shown to demonstrate the control performance. 7 refs., 9 figs., 2 tabs.

  7. Improvement of vehicle stability in cornering on uneven road; Akuro senkaiji ni okeru sharyo no anzensei kojo

    Energy Technology Data Exchange (ETDEWEB)

    Tobimatsu, K.; Harada, M.; Harada, H. [National Defense Academy, Kanagawa (Japan)

    1997-10-01

    The active control of vehicle suspensions and rear wheel steering systems in turning on uneven roads is analyzed by means of LQR control theory, assuming that cornering forces depend on tire normal loads in addition to tire slip angles. The authors quantitatively investigated the effectiveness of the integrated control of the active suspension and the rear wheel steering, comparing the contributions of each individual system. Furthermore, in this paper, the role of the chassis control and driver control are studied in order to improve the stability of vehicle motion disturbed by the road surface. 4 refs., 9 figs.

  8. Seismic reflection survey in Omama fan area, Gunma prefecture; Gunma Omama senjochi ni okeru hanshaho jishin tansa

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, K.; Kano, N.; Yokokura, T.; Kiguchi, T.; Yokota, T.; Matsushima, J. [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-01

    Seismic reflection survey was performed for the Medial Tectonic Line, an important geological tectonic line in the Kanto plains, at Kushibiki district, Saitama prefecture in the north-western part of the Kanto plains. It was estimated that movements of the basement were different in the individual sides of the active fault. In this study, the seismic reflection survey was performed at the Omama fan area, Gunma prefecture, which is located at the north-eastern extension of the Kushibiki plateau, to grasp the structure of basement to the depth of about 1.0 s of return travel time, and the upper sediments. Two traverse lines passing Ota city, Kiryu city, and Nitta town were used. Southern part of the traverse line-1 was in the bottom land in the middle of Tone river, and northern part was in the Omama fan area. The ground surface along the traverse line was flat. Hachioji heights are the heights elongating in the NW-SE direction and having relative height of 100 to 200 m against the surrounding plain. Another traverse line-2 was set on the steep slope having relative height more than 100 m. The Brute stack time section of each traverse line was characterized by the gradient reflection surface AA of the traverse line-1. It was suggested that the AA or intermittent parts of reflection surfaces deeper than AA may relate to the tectonic lines in the more ancient geological ages. 2 figs., 1 tab.

  9. Fault analysis in the very shallow seismic reflection method; Gokusenso jishin hanshaho ni okeru danso kaiseki. 1

    Energy Technology Data Exchange (ETDEWEB)

    Nagumo, S.; Muraoka, S.; Kaida, Y.; Takahashi, T. [OYO Corp., Tokyo (Japan)

    1996-10-01

    To effectively use the very shallow seismic reflection for active fault survey, a method has been investigated by which fault structures can be appropriately reconstructed from the fault information detected in the original records. The first step of reconstructing the fault system from the travel time reflection curve was to grasp an outline of fault structure from the patterns of travel time curve observed in the original record. For the very shallow seismic reflection method, especially, the low velocity layers in a shallow part succeeding from the ground surface made the issue complicated. Then, the travel time reflection curves were calculated in the case of existing several horizontal reflection surfaces in the surface layer. The constant values, mean velocities to the depth at individual reflection surfaces were used for the approximation of velocities. The outline of fault structure was grasped from the observation of original record. Then, the structure was reconstructed from the travel time curves. When the mean velocity in the medium was known, reconstruction of the feature of reflection surfaces from the travel time curves could be determined by simple mapping. When the mean velocity was unknown, it was calculated using the reciprocal travel time from the common reflection surface for individual reflection surfaces. 7 figs.

  10. Study of evaluation for grouting effect in a borehole; Yakueki chunyu koka hyoka gijutsu ni okeru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, H.; Matsuo, T. [Fukuoka Municipal Transportation Bureau, Fukuoka (Japan); Yamauchi, Y.; Imanishi, H. [Osaka Soil Test, Osaka (Japan)

    1996-10-01

    For the foundation improvement works by grouting in a borehole, evaluation of grouting effect is one of the most important management items. The grouting design and works are sometimes reconsidered depending on the evaluation of grouting effect during the test injection. The purpose of the evaluation of grouting effect is to grasp the range of improvement and consolidation after the injection, and to judge and estimate the strength and permeability of the consolidation part. This paper describes the judgment method of the strength using PS logging results and borehole televiewer (BHTV) logging results. The reflection intensity (Ir) by the BHTV logging increased after the grouting, which showed a same tendency as that using S-wave and P-wave velocities (Vs and Vp) before and after the grouting. This was considered to demonstrate the grouting effect. A relation was obtained between the Vs, Vp and Ir before and after the grouting, which was expressed by following equation. Ir=0.143{times}Vs-70=0.093{times}Vp-110. The relation with the dynamic elastic coefficient (Ed) was also obtained as follow; Ir=0.0013{times}Ed. 9 figs.

  11. Interaction effects on combustion of alcohol droplet pairs; Alcohol kei nenryo niekiteki no nensho ni okeru kansho koka

    Energy Technology Data Exchange (ETDEWEB)

    Okai, K.; Ono, Y.; Moriue, O.; Shiba, S.; Araki, M.; Tsue, M.; Kono, M. [The University of Tokyo, Tokyo (Japan); Nomura, H. [Nihon Univ., Chiba (Japan). Coll. of Industrial Technology; Shiga, S. [Gunma University, Gunma (Japan). Faculty of Engineering

    2000-02-25

    Experimental investigation was conducted on two droplet-array combustion of methanol and methanol/dodecanol mixture fuels in microgravity. For methanol, effects of ambient pressure and droplet spacing were examined. Results show that the droplet lifetime decreases with increasing spacing at relatively low pressure and the droplet lifetime becomes independent of spacing at higher-subcritical and supercritical pressures. For methanol/dodecanol mixture, effects of pressure, fuel composition were investigated in terms of occurrence of disruption. Disruption of droplet during combustion was demonstrated both for single droplet and droplet pairs. (author)

  12. 1000m depth boring at Inagawa, Hyogo prefecture. 1. Overviews; Hyogoken Inagawamachi ni okeru 1000m boring chosa. 1. Gaiyo

    Energy Technology Data Exchange (ETDEWEB)

    Sato, T.; Kusunose, K.; Cho, A.; Tosha, T. [Geological Survey of Japan, Tsukuba (Japan); Kiyama, T.; Yamada, F. [Mitsui Construction Co. Ltd., Tokyo (Japan); Aizawa, T. [Sancoh Consultants Co. Ltd., Tokyo (Japan)

    1996-05-01

    Various field experiments were carried out using a 1000m deep borehole at Inagawa town, about 10km north of the focus of the Hanshin-Awaji Great Earthquake and directly above the area where shallow earthquake activities have intermittently occurred. These experiments included stress measurement by hydraulic fracturing, hydrophone-aided VSP, permeability tests and observation of various types of logging. The laboratory experiments were also carried out, including measurement of various properties and stresses of the core samples. The stress-depth relationship, determined by the hydraulic fracturing method, shows that the stress gradient well coincides with the Western Japan standard at a depth up to 700m, whereas it is approximately twice as high as the standard at a depth of 946m, at which core disking and borehole break-out are clearly observed, and hence stresses conceivably concentrate locally. Orientation of the maximum horizontal compressive stress is E-W at a depth of around 600m, but greatly changes to NNW-SSE at a deeper position. 4 refs., 5 figs.

  13. Cut down the peak daytime demand for electricity at the residence; Jutaku ni okeru denryoku fuka heijunka

    Energy Technology Data Exchange (ETDEWEB)

    Ishihara, O. [Kumamoto University, Kumamoto (Japan). Faculty of Engineering

    1996-09-05

    For leveling of power load in small-scale buildings and houses, a test house with actual size was constructed in order to examine soil heat storage system using photovoltaic power generation system and nighttime power. A hundred of polycrystal silicone solar cells with about 5 kW and twenty of amorphous ones were fixed on the roof, to connect with commercial power source by the system interconnection having inverse power flow. For leveling of power load in the periods of heating and cooling, soil heat storage system was applied using nighttime power. Pipes for circulating cooling and heating water were embedded. Heat pump was operated only in the time zone of nighttime power, to obtain cooling and heating source for fan coil unit in the daytime. The sold power was larger than purchased power under continuous cooling condition for twelve hours in summer. Since cooling load was supplied from nighttime power with lower price, there was a large peak cut effect in the daytime. As a result of the tests using a house with actual size, the system was found to be applied practically both in summer and in winter. Effectiveness of peak cut of power load in summer was also provided. 7 refs., 10 figs., 2 tabs.

  14. Future vision of advanced telecommunication networks for electric utilities; Denki jigyo ni okeru joho tsushin network no shorai vision

    Energy Technology Data Exchange (ETDEWEB)

    Tonaru, S.; Ono, K.; Sakai, S.; Kawai, Y.; Tsuboi, A. [Central Research Institute of Electric Power Industry, Tokyo (Japan); Manabe, S. [Shikoku Electric Power Co., Inc., Kagawa (Japan); Miki, Y. [Kansai Electric Power Co. Inc., Osaka (Japan)

    1995-06-01

    The vision of an advanced information system is proposed to cope with the future social demand and business environmental change in electric utilities. At the large turning point such as drastic reconsideration of Electricity Utilities Industry Law, further improvement of efficiency and cost reduction are requested as well as business innovation such as proposal of a new business policy. For that purpose utilization of information and its technology is indispensable, and use of multimedia and common information in organization are the future direction for improving information basis. Consequently, free information networks without any limitation due to person and media are necessary, and the following are important: high-speed, high-frequency band, digital, easily connectable and multimedia transmission lines, and cost reduction and high reliability of networks. Based on innovation of information networks and the clear principle on advanced information system, development of new applications by multimedia technologies, diffusion of communication terminals, and promotion of standardization are essential. 60 refs., 30 figs., 5 tabs.

  15. Future petroleum geophysicists and SEGJ; Sekiyu gyokai ni okeru butsuri tansa gijutsusha no shoraizo to Butsuri Tansa Gakkai eno kitai

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, A. [Japan Petroleum Exploration Corp., Tokyo (Japan)

    1998-08-01

    This paper describes future petroleum geophysicists and an anticipation to SEGJ (The Society of Exploration Geophysicists of Japan). Among various elemental technologies, it is undoubted that three-dimensional seismic exploration would be a main technology for prospecting petroleum gas. In the early stage of three-dimensional exploration, an improvement of accuracy for geological evaluation was a major purpose based on the successful exploratory drilling. In the 1990`s, some companies have a policy in which three-dimensional exploration is initially employed especially for the marine seismic prospecting as a major exploration technology. Since simple structures have been already prospected, it is required to prospect more complicated traps with higher accuracy. It is also required to shorten the turnaround time from the initial prospecting to the start of production. Furthermore, the three-dimensional exploration is used as a control technology for advancing the recovery by improving the accuracy of reservoir management. It is required for the geophysicists to have wide knowledge with keeping original exploration technologies. 2 refs.

  16. Feasibility study on introducing new energy systems into Asian villages; Asia sonraku ni okeru shin energy donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For improvement of living standards in unelectrified areas of Asia, the feasibility of new energy power generation systems was surveyed. The degree of electrification of local areas is different every country, and Thailand is ahead of other countries, while Laos and Cambodia are most unelectrified. Power supply of 100W/house seems to be adequate for local areas because of weather condition, housing situation and life-style. Economic support and education on electricity are necessary for poor areas. Although needs for new energy is increasing, the priority is given to industrial and urbanized areas because of cost and investment effects, and remote areas are dependent on grant- in-aid. Resources of photovoltaic, wind power and micro- hydraulic energies are abundant, however, selection of energy and verification of its usability are important, and the local energy density maps were thus prepared. In introduction of new energy, after selection of energy suitable for an area concerned, such geographical and social conditions should be surveyed as road condition, water rights, land utilization, economic support system, policy and intention of inhabitants. 76 refs., 68 figs., 91 tabs.

  17. Rejection of salts in nanofiltration of skim milk; Dasshinyu no nano roka ni okeru enrui no soshiritsu

    Energy Technology Data Exchange (ETDEWEB)

    Sato, I.; Kikuchi, M.; Sakurai, K. [Morinaga Milk Industry Co., Ltd., Tokyo (Japan)

    2000-11-10

    The authors carried out nanofiltration of skim milk and analyzed the salt rejection data using the extended Nernst-Planck equation. The following observed rejections of major constituents in salts were obtained. Na and K: 50 to 60 %, Cl: -5 to 15 %, Ca, Mg and P: > 97 %. It is considered that since Ca and Mg are mostly combined with phosphate and citrate in milk, they were rejected by a sieving effect, thus producing high rejections. Electroneutrality in permeate, and no-electric-current condition in solute flux are observed, respectively. In the subsequent analysis, the authors used a set of proposed assumptions, (1) a complete rejection of solute except Na, K and Cl by the membrane, (2) existence of a fixed charge in skim milk due to impermeable ions of proteins, etc. Rejection of Na, K and Cl calculated from the analysis are in good agreement with those of the experimental data. (author)

  18. Interphase boundary structure and transformation mechanism in diffusional phase transformations; Kakusan hentai ni okeru iso kaimen kozo to hentai kiko

    Energy Technology Data Exchange (ETDEWEB)

    Furuhara, T.; Maki, T. [Kyoto University, Kyoto (Japan)

    1997-05-20

    This paper discusses a lattice changing mechanism in diffusional phase transformations (atom diffusion rate determination) based on observations through a high-resolution electron microscope. If a parent phase and a generated phase have different crystal structures, change in lamination occurs as a result of a step generated on a terrace with good consistency moving in the horizontal direction. In addition, it has been thought that removal of atoms occurs due to random diffusion jump in a riser or a kink which has a locally inconsistent structure, and no surface undulations will occur. On the other hand, growth interfaces are consistent in martensite transformation, and atomic correspondence is univocal in the parent phase and the generated phase. Also in diffusion transformation accompanying distribution of displacement type elements, the surface undulations will appear as in the case of the martensite transformation. This fact suggests that, also in the diffusional transformation, not only the terrace interface, but also the riser or kink interface having been thought inconsistent conventionally are all consistent or semi-consistent as in the martensite transformation. It also suggests that lattice correspondence exists between the parent phase and the generated phase. 30 refs., 16 figs., 1 tab.

  19. Superplasticity of low carbon HSLA steel during bainite transformation. Teitanso teigokinko no beinaito hentai ni okeru chososei kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Nakajima, H.; Yamamoto, S.; Miyaji, H.; Furubayashi, E. (National Research Inst. for Metals, Tsukuba, Ibaraki (Japan))

    1993-12-01

    Recently, the development of high strength low alloy steel (HSLA steel) of untempered type is advanced by using the comparatively high strength and excellent tenacity of the bainite or martensite of carbon remained being transformed. In the present researches, the superplasticity during the bainite transformation due to the continuous cooling and changes of the structure as well as the mechanical properties due to the superplastic deformation are examined with the samples of Mn-Cr-Mo system HSLA steel. The results obtained therefrom are shown as follows. The temperatre range of B[sub S] and bainite transformation is moving to the higher temperature side along with the increasing of the applied stress when it is over 60 MPa. The bainitic structure is composed of the mixture lath-like bainitic ferrite and granular bainitic ferrite in the use of having no applied stress, while the percentage of the latter increases simultaneously with the increasing of the applied stress. Transformation superplastic strain is increasing together with the increasing of the applied stress, and its increasing is over the linear function when the applied stress is above about 50 MPa. 22 refs., 9 figs., 2 tabs.

  20. Education for hydraulics and pneumatics in Nippon Institute of Technology, Department of Mechanical Engineering; Nippon Kogyo Daigaku ni okeru yukuatsukyoiku

    Energy Technology Data Exchange (ETDEWEB)

    Terashima, Y. [Nippon Institute of Technology, Saitama (Japan)

    2000-03-15

    Described herein is education of hydraulics and pneumatics in Nippon Institute of Technology. Department of Mechanical Engineering has fluid dynamics, mechatronics II, air conditioning, heat transfer engineering, and facility and equipment engineering as the themes related to hydraulics and pneumatics. The control engineering courses have the pneumatics-related themes of supply of pneumatic pressure for a short time and methods for cutting off pneumatic pressure when the piston reaches the dead center, as the energy-saving type driving methods for pneumatic cylinders; measurement of frictional force by the experiments on low-friction cylinders; and researches on improvement of stiffness of pneumatic cylinder type actuators for control valves, among others. Students are directly involved in equipment designs, fabrication and experiments. Many machines and facilities are now easily handled, and operated according to manuals. To prepare graduation theses only by the aid of personal computers is not adequate for education of students in this age, when they have less chances for education through experiences in affluent environments. The mechanical engineering students are given chances for practical education through experiments and graduation thesis preparation. However, it is necessary for general engineering students to be more exposed to technical practices. (NEDO)

  1. Non-linear mechanical simulations in space structures engineering; Uchu kozobutsu kogaku ni okeru hisenkei kikai rikigaku simulation

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, K. [Kinki Univ Osaka (Japan)

    1997-08-05

    Space structure engineering comes under the combination of different engineering fields. Role of numerical analysis and simulation is large in space structure engineering. Considering space structure engineering as an application of non-linear mechanical simulation, constrains with simulation technology and analysis examples are explained in this paper. Following important points are confirmed by simulating the motion of membrane under external force acting on inner and outer surfaces at a particular point of square satellite model which rotates in tension membrane. When the external force is removed, each material point and membrane centre move with vibration, however centre of gravity of satellite moves very rapidly along the vertical direction of membrane centre. Further external disturbance (which develops on material points) propagates at all material points and membrane centre as a twisted wave. Maximum relative displacement between inner surface and outer surface decreases with the increment of initial angular velocity but not on the points of upper membrane. Fluctuation of position motion of satellite resulted from external disturbance is become small as initial rotation angular velocity increases. 10 refs., 6 figs., 2 tabs.

  2. Education for fluid power in department of mechanical engineering of Sophia University; Jochi Daigaku Kikai kogakuka ni okeru yukuatsu kyooiku

    Energy Technology Data Exchange (ETDEWEB)

    Tsukiji, T. [Sophia University, Tokyo (Japan). Faculty of Faculty of Science and Technology

    2000-03-15

    Curricular guidelines are that importance be attached in the educating policy to the primary subjects of study and that compulsory subjects are to be acquired through practice. Out of primary subjects, those which should better be learned by all the students are set as compulsory subjects. Related subjects are divided into fluid-related subjects and control-related subjects. Experiments are conducted of the 'inspection of orifice flowmeter and Bourdon tube pressure gage,' 'fluid friction in round tube,' and 'servo-mechanism.' In a lesson on drafting, hydraulic equipment provided by business corporations is used. It is hoped that educating units be provided. Subjects of research for graduation and master's theses are the turbine-driven pump, constant pressure source system, hydraulic drive system, application of control theory to an injection molding machine, highly intelligent fluid, noise reduction for an automotive compressor, state of fluid in a hydraulic control valve, analysis of flow in pneumatic equipment elements, and cavitation in a vane pump. More than half of these subjects are pursued in collaboration with industrial or Government circles. It is expected that the Society will be an organization to benefit the students. (NEDO)

  3. Optimal control of reflux ratio for batch distillation; Bacchi joryu ni okeru kanryuhi no saiteki kido to seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Morimoto, Jun [Sankyo Corp., Tokyo (Japan); Suzuki, Mutsumi [Tohoku University, Miyagi (Japan). Department of Chemical Engineering

    1999-03-10

    To obtain maximum production under minimum utility-cost, the optimal operation of reflux ratio is considered for a batch distillation process. Pontryagin's maximum principle is one of the solutions to calculate such an optimal operation, but it requires extensive trial and error. In this paper, a faster algorithm is proposed to modify the initial values of Hamilton's multiplier. With the rapid growth of computer power, this algorithm will provide a way to realize the real-time optimization and control of the reflux ratio. To reduce the on-line calculation, a control table for the optimal operation can by calculated off-line as a function of state variables. These control methods provide the real optimal operation for a given evaluation function. (author)

  4. Analysis of fuel spray characteristics for premixed lean diesel combustion; Kihaku yokongo diesel kikan ni okeru nenryo funmu kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, S.; Harada, a.; Miyamoto, T.; Akagawa, H.; Tsujimura, K.

    1997-10-01

    Premixed lean diesel combustion (PREDIC) makes it possible to achieve low NOx emission. It is an important factor to make the homogeneous spray formation for PREDIC. In this paper presents I the effect of the spray dispersion on emission characteristic were analyzed with the spray observation and engine test. Pintle type nozzle, which has different feature from orifice type nozzle, are used to form the hollow cone spray. As a result, the pintle type nozzle having grooves to generate the swirl flow, makes the reduced penetration in comparison with the hole nozzle under low ambient gas pressure. And it could improve THC, CO emissions at low NOx emission condition. 7 refs., 12 figs., 1 tab.

  5. Analysis of flame propagation phenomenon in simplified stratified charge conditions; Tanjunkasareta sojo kyukiba ni okeru kaen denpa gensho no kansatsu

    Energy Technology Data Exchange (ETDEWEB)

    Moriyoshi, Y.; Morikawa, H. [Chiba University, Chiba (Japan); Kamimoto, T. [Tokyo Institute of Technology, Tokyo (Japan)

    1997-10-01

    Since the local inhomogeneity of mixture concentration inside the cylinder affects the combustion characteristics, a basic research on combustion phenomenon in stratified charge conditions is required. The authors have made experiments with a constant-volume chamber, which can simulate an idealized stratified charge field by using a removable partition, to obtain the combustion characteristics. Also, numerical calculations are made using some combustion models. As a result, the important feature that the combustion speed is faster in stratified condition than in homogeneous condition can be predicted by the two-step reaction model. 4 refs., 8 figs.

  6. Water monitoring and its information management system in China; Chugoku ni okeru suishitsu monitoring to joho kanri system

    Energy Technology Data Exchange (ETDEWEB)

    Quan, H.

    1996-01-10

    This paper summarizes the water monitoring system (WMS) in China applied mainly to surface water and operated within the competence of the Environmental Protection Agency. The WMS consists of a national water monitoring network and a water information system that monitors surface water periodically. The WMS comprises water monitoring stations classified from class 1 to class 4, which are located in 2,222 locations. Stations from class 1 to class 3 are operated by using computers, but class 4 stations are still incapable to use floppy disks to perform information transmission. When an information management system is completed at the China-Japan Friendship Environmental Protection Center being constructed by gratis assistance from the Japanese Government, transmission of water quality data will become possible by means of the cable line system in addition to the table system and the floppy system. The water quality data are published to general people in the forms of Chinese gazette for the environmental conditions, the environment yearbook, and the reports on environmental quality. However, the more important is to publish more publications to make people aware of the actual state of water pollution and have them cooperate in environment preservation. 4 refs., 1 fig.

  7. Trends in developing alternative energies in Sweden. Sweden ni okeru daitai energy kaihatsu no doko ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Maruyama, S. (The Kansai Electric Power Co. Inc., Osaka (Japan))

    1992-07-10

    This paper introduces a summary of the survey made on the Swedish policies on alternative energies. The country has a characteristic that the alternative energy policies have a great importance for each political party as its reigning strategy. The largest weight for the alternative energies is placed on bioenergies. Sweden has been already depending on bioenergies at 15% of the country[prime]s total energy supply. Nearly half amount of the budget in the new five-year alternative energy plan approved in 1991 is bioenergy related. The budget of 3.76 billion kronor can be broken down into 1 billion kronor for effective energy utilization, 1.92 billion kronor for bio-fuel utilization, and 800 million kronor for bio-fuel utilizing plants. The bio-fuel utilizing plants include improved CFB utilizing steam cycle power generation, gasified compound cycle power generation, a bio-fuel/natural gas compounding plan, and a bio-fuel/caustics recovery boiler compounding plan, each having merits and demerits. Thirty-five wind power generating plants are in operation producing a total power of about 10,000 MWh in 1990. 3 figs., 4 tabs.

  8. Needs for intelligent field sensors in petrochemical plants. Sekiyu kagaku plant ni okeru intelligentter dot fieldter dot sensor eno needs

    Energy Technology Data Exchange (ETDEWEB)

    Tsukahara, T. (Idemitsu Kosan Co. Ltd., Tokyo (Japan))

    1990-08-05

    This report explains the process sensors used in petrochemical plants. To establish a safety and accident preventing systems, the function of a sensor to substitute the five senses of an operator is demanded. A man inspects using the senses of seeing, hearing, touch and smell, and takes measures judging from all factors, not from the state of one point. For a wide-range monitoring function, there is a need for a robot which is loaded with sensors of various intelligences and which moves freely at the field. When many sensors are configurated for the wide-range monitoring, the maintenance of system comes into question. The sensor with intelligent functions recently developed can contribute to the maintenance because it is highly accurate and it has the function of self-diagnosis. If it becomes possible to process data with the sensor at the field utilizing the intelligent function, the central control room will be miniaturized and automatization will be pushed forward remarkably. 3 refs., 2 figs.

  9. Polymer-based matrix composites in general industries. Ippan sangyo bun'ya ni okeru kobunshiki fukugo zairyo

    Energy Technology Data Exchange (ETDEWEB)

    Kenmochi, K. (National Institute of Materials and Chemical Research, Tsukuba (Japan))

    1994-02-15

    This paper summarizes the course of development of polymer-based matrix composites (PMC) begun in the 1950's, their future problems, and prospects. Because of PMC being a petroleum product, the changing period before and after the first and second oil crises (1974-1983) has seen even a negative growth from the declined product price out of increased material cost. However, the materials have been continuing expansion in such applications year after year for two decades since then as plant, marine vessel, and housing materials. The course of their development to date has included such proliferation impeding factors as unproved reliability, high production cost, and legal regulations because of being new materials. However, the ardent technical development efforts having produced a number of products including hybrid FRP, particularly the fundamental technology development studies sponsored by the Ministry of International Trade and Industry, have improved properties and reliability and contributed largely to expanding practical applications. Sought in different functions expected in PMC in the future would be application of bionic designs, transfer from functional quality to sensitive quality, and development of material recycling techniques. 8 refs., 11 figs., 1 tab.

  10. Review on departure time choice theory for highway traffic; Doro kotsu ni okeru shuppatsu jikoku sentaku ni kansuru kenkyu kaisetsu

    Energy Technology Data Exchange (ETDEWEB)

    Kuwahara, M. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

    1998-04-01

    This paper explains theoretical results achieved to date on the fundamental theory for time smoothing which is drawing attention as a measure to mitigate traffic congestion, that is departure time choice theory for highway traffic. If a trip having a definite restriction on arrival time is used as an object of the discussion, the travel expense for a traveler consists of an expense for travel time when a car was driven at free speeds, an expense for waiting time at bottlenecks, and an expense incurred by schedule delay (s). Under an assumption that the traveler selects departure time to minimize the expense, a time-based equilibrium condition can be introduced. If a schedule expense function (f(s)) to convert `s` into an expense is convex with regard to the `s`, the first in first work (FIFW) principle can be established, that the bottleneck is reached in the order of earlier departure time that is desired. Thus, starting from handling numerically the relationship between queuing expense function in the bottleneck and the f(s), the theory developed to the multiple bottleneck and random effect theory. 19 refs., 8 figs.

  11. Engineering technologies for steel structure applied to Trans-Tokyo bay highway project; Tokyowan odan doro ni okeru kokozo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Furumuro, K.; Kobayashi, T.; Kanda, K. [Kawasaki Steel Corp., Tokyo (Japan)

    1996-03-01

    The Trans-Tokyo Bay Highway is a 15.1 km toll road that spans the Tokyo Bay from Kawasaki City in Kanagawa Prefecture to Kisarazu City in Chiba Prefecture by a bridge, an undersea shield tunnel, and two man-made islands. Many new technologies and methods were introduced to construct a large-scale structure safely, rationally, and in a short time on the weak ground under the depth of water in a seismic region such as Tokyo Bay. Kawasaki Steel participated in this project in: (1) development and construction of a revetment structure to which the technology of an oil drilling jacket was applied, (2) design and construction of a large-sized bridge with long-span and multi-span continuous girders on the sea, and (3) design and installation of a mud water treatment module for the shield tunnel constructed on the sea. As a result, the bearing-capacity measurement technology based on the dynamic method of a large diameter steel pipe pile was developed in item (1). The long-term corrosion-proof method using titanium clad steel was developed in item (2), and the way to construct the treatment facilities of approximately 5100 tons in item (3). 3 refs., 12 figs.

  12. Steel structure (bridge and building); Doboku/kenchiku bun`ya ni okeru yosetsu gijutsu no tenkai

    Energy Technology Data Exchange (ETDEWEB)

    Fukazawa, M. [Yokogawa Bridge Corp., Tokyo (Japan)

    1996-01-05

    In this article, the trends of welding engineering are discussed in two groups, namely bridges and steel frames. First of all, in the field of bridges, as the themes of technical innovation of steel bridges, the challenge to build long span bridges, coping with new structural forms, and rationalization of general bridges are selected. Concerning very long bridges, considerable elongation of its spans and technological development for materials, design, construction and erection relating to improvement of profitability become inevitable. Besides, in addition to the functions of bridges, the bridges playing the roles of environmental and/or artistic structures become many, thereby the cases of using welding for the site joints increase. As the measure for rationalize bridge construction, it is to reduce steel weight and working costs for increasing profitability, and the progress of welding technology therefor has been observed. With regard to the manufacture of bridge portions in a factory, labor saving, automatization and robotization of in-house welding have been made, and bridge maintenance as well as pursuance of attaining the state of maintenance free are also important. The trend that the bridge load is becoming larger and enhancement of earthquake resistance are also important. Regarding steel frames, functionalization of steel, making steel very thick, various automatization of manufacturing, and pursuance of earthquake resistant safety are being made. 14 refs., 7 figs.

  13. NEDO`s solar energy program in developing countries; Hatten tojokoku ni okeru NEDO no taiyo energy project

    Energy Technology Data Exchange (ETDEWEB)

    Honda, T. [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1998-05-31

    This paper describes the solar energy program promoted in developing countries by NEDO. Research of photovoltaic power generation systems for middle-scale villages has been conducted in Indonesia between FY 1984 and FY 1989. International cooperative demonstration development for photovoltaic power generation systems has been conducted in Nepal, Mongolia, Thailand and Malaysia for five to six years since FY 1994. For the research of solar heat, air heat collection type drying systems using solar heat has been promoted between FY 1993 and FY 1998. Employment of solar micro hydraulic power hybrid systems is planned in regions with rainy and dry seasons. In FY 1997, photovoltaic power generation systems were constructed in Gansu, Sinkiang Uighur, and Hopeh in China for operation researches. Durability tests have been conducted in Oman. A plan of construction of photovoltaic power generation systems with a capacity from a few MW to 1 GW at maximum in deserts is to be promoted as international cooperative activities with PVPS of IEA and CTI. Japan will play a major role on the activities as a proposal country based on the achievement of PVTEC. 6 figs., 2 tabs.

  14. Possibility of EV with solar cells on the new traffic system; Shinkotsu system ni okeru solar car no kanosei

    Energy Technology Data Exchange (ETDEWEB)

    Fujii, I.; Kojima, S. [Meiji University, Tokyo (Japan)

    1997-11-25

    A possibility of a new traffic system was studied for a solar car which is light in weight, small in size and low in speed (cruising speed: 20 km/h) and does not need so much power because of the use for short distance. In the new traffic system, people travel short distance in city by solar car, and use trains for travel between cities. By installing solar cells on roofs, etc. of houses and buildings such as garages around stations, power needed for solar car and incidentally required can be supplied. Assuming the short distance transportation, the car is for one person with a height of luggage space of 70cm, mean length of 165cm, and floor height of 50cm above the ground. In case that the power generation by solar cells (256.5W) is at maximum with no shading during travel on conditions of load weight of 10kg, personnel weight of 70kg, and total weight of 250kg, it was found that solar cells can supply 89% of the required output under test road travel at speed of 20 km/h. A viability of the solar car proposed here is great. A possibility at the time of mode road travel is also studied. 10 refs., 3 figs., 1 tab.

  15. Desiliconization process of hot metal at blast furnance casthouse. Koro chusho ni okeru yosen no tatsukei shori

    Energy Technology Data Exchange (ETDEWEB)

    Uchiyama, T.; Takeda, K.; Taguchi, S.; Shinohara, K.; Kato, H.; Matsumoto, T. (Kawasaki Steel Corp., Tokyo (Japan))

    1990-09-01

    The Kawasaki Steel has developed several types of desiliconization facilities at blast furnace runner and applied to blast furnaces according to their individual local conditions. In response to the restriction in the maximum feed rate and mass velocity of desiliconization reagent by the slag foaming and splash formations for the desiliconization method without slag removal at the casthouse, three methods, i.e., a top feed method, a blasting by one stage, and a blasting by two stages were developed, according to increases in the required feeding rate of the desiliconization reagent. In the case that the desiliconization slag is removed at the blast furnace runner, it was demonstrated that the injection method by use of an immersion lance was effective because of its high oxygen efficiency in desiliconization. An simulation model of desiliconization was also developed, and the effect of the lance shape on oxygen efficiency in desiliconization was evaluated. On the basis of the simulation results, the oxygen efficiency in desiliconization was able to be increased to 60% by the improvement of the injection conditions. 8 refs., 18 figs., 3 tabs.

  16. Present status and amendable subjects of brewery CIM. Beer kojo ni okeru CIM no genjo to kadai

    Energy Technology Data Exchange (ETDEWEB)

    Eguchi, T.; Kimura, T. (Asahi Breweries, Ltd., Tokyo (Japan))

    1991-12-10

    Though the beer consumption is being smoothly increased, there has been a considerable change in consumers prime taste of beer for these several years. The present report exhibits the computer integrated manufacturing system introduced in Ibaraki Brewery, Asahi Beer to be operated as per the target. The introduction of that system aimed at an execution of integrated administration, high particularly in quality control, to integrate the information and control of total production activities from the production planning to the product delivery. Together with the structuring of information system for the integrated production, aim was taken also at the heightening in quality control, heightening in administration level, labor saving and newly conceived distribution system. As for the structuring of hardware, the system was functionally classified into production planning level, administration level for the manufacturing and distribution, and control level for the processing and distribution. Each of those levels was accommodated with the most suitable machinery thereon. The future problems are about the quality control data measurement and widened application of database. 5 figs.

  17. Dream of future on human-machine cooperative system; Ningen robot system ni okeru fluid power gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, Y. [Hosei University, Tokyo (Japan). Faculty of Engineering

    2000-01-15

    This paper describes the human-machine cooperative system and fluid power technology. Most of Japanese robot R and D activities shifted from early R and D on hydraulic or pneumatic driving to that on simple electric driving, and development of fluid power technology as actuator and control technology is retarded. For creating an artificial work environment with a presence by virtual reality formation technology, an equipment (actuator) directly acting such five senses (sensor) of operators as visual, auditory, pressure and contact senses is essential. Pneumatic actuator is extremely suitable for such one because of its small size, light weight, safety and high power density. Robocup has been held as the soccer game of many autonomous robots. For the soccer game of human beings and robots, development of such technologies for advanced autonomous robots is necessary as realtime processing, advanced intelligence, human friendliness, safety, high-efficiency high-power actuator equivalent to human muscle, and energy source. (NEDO)

  18. Magnetic constraints of basement structure offshore of western Kyushu, Japan; Kyushu seiho kaiiki ni okeru jiki ijo no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Okuma, S.; Nakatsuka, T. [Geological Survey of Japan, Tsukuba (Japan); Ishihara, T. [Japan National Oil Corp., Tokyo (Japan)

    1996-05-01

    This paper describes the results from the qualitative analysis of magnetic anomalies offshore of western Kyushu and from an analysis by a three-dimensional two-layer model inversion. The analysis ranged from Kyushu on the east to Jeju Island on the west and from the southern part of the Korean Peninsula on the north to Tanegashima and Yakushima Islands on the south, namely, the area of 580km from east to west and 580km from south to north. The analytical data used was Magnetic Anomaly Map of Asia (GSJ and CCOP, 1994). In the qualitative analysis, a pseudogravity anomaly map and a pole gravity anomaly map were prepared from the total magnetic force anomaly map by means of a frequency filter operation. As a result, it was noted that two distinctive magnetic high belts existed in the margin of the Tunghai Shelf, extending from the sea area to the west of the Nansei Islands continuously to NNE, and being distributed transversely through the Goto sedimentary basin. Additionally, in the inversion analysis, it was demonstrated that the magnetic basement became shallow at the margin of the Tunghai Shelf north of latitude 31 degrees north, extending nearly in the NNE direction through west of the Goto Islands, west of Tsushima Island, and continuing to the southern coast of the Korean Peninsula. 6 refs., 4 figs.

  19. MT2-D inversion analysis in Kakkonda geothermal field; Kakkonda chinetsu chiiki ni okeru MT ho nijigen kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Yamane, K.; Takasugi, S. [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Miyazaki, S. [Japan Metals and Chemicals Co. Ltd., Tokyo (Japan); Uchida, T. [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1996-05-01

    Data, collected from an MT method-assisted survey conducted in the Kakkonda geothermal region in 1987, was re-examined, and a new structure was found. The review was carried out by use of a 2D analysis in the TM mode. According to the 1D analysis of 1987 and the geological data gathered then, it is estimated that the resistivity structure of this region runs in the northwest-southeast direction. A northeast-southwest traverse line was set for this analysis, orthogonal to the strike, and the impedance at each observation spot was caused to rotate to this direction across the whole range of frequency. Furthermore, in 1994-95, surveys were conducted using arrayed CSMT/MT methods. All these sum up to indicate that a high-resistivity region extends northwest in the southwestern part of the Kakkonda river but that there exists a low-resistivity region of several 10 Ohm m centering about the B traverse line. The high-resistivity region deep in the ground being the target of excavation in the Kakkonda region, to collect knowledge about this high-resistivity is important, and here the effectiveness of the 2d analysis has been verified. 5 refs., 11 figs.

  20. On noise, traffic and factory vibrations in Akita city; Akitashi ni okeru soon oyobi kotsu kojo shindo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Nogoshi, M.; Kikuchi, T.; Morino, T.; Sannohe, M. [Akita University, Akita (Japan). College of Education

    1996-05-01

    Noise and vibration were measured in Akita City. In 1994, noise and traffic-caused vibration were measured along the trunk lines and other roads across the entire Akita City area. In 1995, the effort centered on the Ibarashima manufacturing quarters, the important source of noise and vibration in Akita city. The general-purpose noise meter LA-220S was used to measure noise and the vibration level meter VR-5100 was used to measure vibration. The results of noise measurement carried out at 122 points in Akita City indicated that the noise level was high along Route 7, Route 13, and the southern line belonging to the newly built national highway, marking the highest of approximately 74dB. As compared with the measurement made in 1968, the value was higher by 3-13dB. A roughly similar trend was seen in vibration. The noise level measurement of 1995 accomplished at 100 points in the vicinity of Ibarashima district indicated that the factories were responsible for high levels of noise and vibration. It was found that the levels lowered in proportion to the increase in the distance from the factories. 11 figs., 1 tab.

  1. Remote reference processing in MT survey using GPS clock; MT ho ni okeru GPS wo mochiita jikoku doki system

    Energy Technology Data Exchange (ETDEWEB)

    Yamane, K.; Inoue, J.; Takasugi, S. [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Kosuge, S. [DRICO Co. Ltd., Tokyo (Japan)

    1996-05-01

    A report is given about the application of a synchronizing system using clock signals from GPS satellites to a remote reference method which is a technique to reject noise from the MT method. This system uses the C/A code out of the L1 band waves from NAVSTAR/GPS satellites. The new system was operated in MT method-using investigations conducted at China Peninsula, Aichi Prefecture, and Izu Peninsula, Shizuoka Prefecture, with the reference points placed several 100km away in Iwate Prefecture on both occasions. It was found as the result that it is basically possible to catch signals from the GPS at any place, that the signals are accurate enough to be applied to time synchronization for the MT method, and that the signals assure a far remote reference method with a separation of several 100km between the sites involved. The referencing process at high frequencies whose feasibility had been doubted proved a success when highly correlated signals were exchanged between two stations over a distance of several 100km. 5 refs., 9 figs.

  2. Noise and vibration reduction technology in hybrid vehicle development; Hybrid sha kaihatsu ni okeru shindo soon teigen gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshioa, T.; Sugita, H. [Toyota Motor Corp., Aichi (Japan)

    2000-03-01

    Accomplishing both environmental protection and good NVH performance has become a significant task in automotive development The first-in-the-world hybrid passenger car of mass production. 'Prius', has achieved superior NV performance compared with conventional vehicles with a 1.5-liter engine along with 50% reduction of fuel consumption and CO{sub 2} emissions. low HC, CO and NO{sub x} emissions. This paper describes NV reduction technology for solving problems peculiar to the hybrid vehicle such as engine start/stop vibration, drone noise at low engine speed and motor/generator noise and vibration. It also mentions application technology of low rolling resistance tires with light weight wheels and recycled material for sound proofing. (author)

  3. Function of Regenerator in the multi staged regenerative refrigerator; Tadan chikureigata reitoki ni okeru chokureiki no kino

    Energy Technology Data Exchange (ETDEWEB)

    Inoue, T.; Nogawa, M.; Zhu, S. [Aisin Seiki Co., Ltd., Aichi (Japan)

    1999-11-10

    On the function of regeneration vessel, which is the base element of regeneration type refrigerating machine, there is two of viewpoint as a heat exchanger greatly separate and viewpoint as an energy converter. Here, to begin with, the function of regeneration vessel as energy converter is arranged, and especially, both expression is compared on the expression of the regeneration vessel efficiency. In addition, the essence of multistage used in the cooling of the regeneration type refrigerating machine is examined from the viewpoint of the function of the regeneration vessel. (NEDO)

  4. Design method for heat exchanger of stirling cycle machines; Sutaringu saikuru kikan ni okeru netsu kokanki no sekkei shuho

    Energy Technology Data Exchange (ETDEWEB)

    Sekiya, H. [Sanyo Electric Co., Ltd., Tokyo (Japan)

    1999-11-10

    Recently, the Stirling cycle organization attracts the attention as 1 of the countermeasure to the global environmental problem, and the tendency of various application equipment developments heightens. The main factor is in constructing CFC elimination refrigeration air conditioner, and the development example as an engine for power source of refrigerating machine used in the ultra-low-temperature region and equipment variously is reported. In this paper, practical design tool and design examination case are introduced, while design technique of heat exchanger, which is the most important in design development of these, ST refrigerating machine and ST engines is described. (NEDO)

  5. Estimation of course stability at initial design stage; Shoki sekkeiji ni okeru shinro anteisei no suitei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yukawa, K. [Ministry of Transportation, Tokyo (Japan)] Kijima, K. [Kyushu Univ., Fukuoka (Japan)

    1998-12-31

    The theoretical prediction method for the hydrodynamic forces acting on the ship hull in maneuvering motion in consideration of effect of frame line configuration is proposed, selecting six types of model ships as the calculation objects. The prediction results show that the hydrodynamic forces can be predicted with reasonable accuracy in the ordinary maneuvering motion range, though the large drift angle and high dimensionless rotation angular speed give some errors. Using the linear differential coefficient obtained from the prediction of hydrodynamic force acting on ship hull, the decrease in the course instability is investigated. It is found that the method is able to be used for predicting the course stability of ships with relatively good accuracy. This method will be useful to decrease the course instability due to the difference in change in local shape of ships. Study will be continued on estimation calculation of hydrodynamic force on ship hull having various kinds of types. 13 refs., 15 figs., 2 tabs.

  6. Power feeding to terminal devices in optical subscriber network; Hikari fuaiba tsushin ni okeru tanmatsu kiki eno kyuden

    Energy Technology Data Exchange (ETDEWEB)

    Yamasaki, M

    1998-09-01

    This paper outlines present state of the feeding system in the light access system in consideration of backup in case of home power failure. In the optical communication, equipment with bilateral conversion function for light and electricity has to be installed both on communication service side and home side. Outline of the light access system and equipment requiring backup are shown. The following items are explained: main types of the light access system, such as FTTC (fiber to the curb), FTTP (fiber to the pole), FTTH (fiber to the home) and HFC (hybrid fiber coax), and the feeding system; problems on feeding system for the light access system. Key elements of ONU (optical network unit) for FTTH and construction of the ONU power source are illustrated. The ONU power source is composed of a backup power supply unit and main body supply unit. Backup power is indispensable to the ONU and analog telephones: output is supplied by the backup batteries in power failure. For miniaturization of the backup power source, power supply circuits and backup batteries have to be miniaturized simultaneously. History of miniaturization is explained on the experimental models. 6 refs., 7 figs., 1 tab.

  7. Measurement of organic carbon quantity at chemoautorophic bacterium; Kagaku dokuritsu eiyo saikin ni okeru yuki tansoryo no sokutei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Tsuda, I.; Kato, K.; Nozaki, K. [Electrotechnical Laboratory, Tsukuba (Japan); Kurokawa, K. [Tokyo University of Agriculture and Technology, Tokyo (Japan)

    1996-10-27

    Described herein is the method for analyzing quantity of organic carbon synthesized by chemoautotrophic bacterium. It is based on the combustion-infrared spectroscopy, which is normally adopted for quantitative analysis of organic carbon. The problems involved in the measurement of organic compounds synthesized by iron-oxidizing bacteria are noise by culture medium components, aging of gas analyzer and contamination with organic compounds from a silicon plug. The measures taken in this study against these problems include comparison of the results with a medium containing iron-oxidizing bacteria with those with a medium free of these bacteria, calibration with the standard solution for each measurement, and replacement of a silicone plug by a silicon cap. Organic carbon is measured by a TOC-5000 analyzer equipped with an automatic sample feeder ASI-5000. Biomass density is determined by the MPN method. It is confirmed that organic carbon quantity is almost in proportion to biomass density, a phenomenon which can be used to determine organic carbon quantity. 7 refs., 6 figs., 1 tab.

  8. Reinstatement of material research in the 21st century; 21 seiki ni okeru zairyo kenkyu no fukken

    Energy Technology Data Exchange (ETDEWEB)

    Shinbara, K. [Osaka Univercity, Osaka (Japan). Institute of Scientific and Industrial Research

    2000-03-10

    Just before the 21st century, Japan is demanded most importantly of reforming the industrial structures, breeding new industries, and working on global environment and energy problems. To solve these problems, emergence of material technologies based on original ideas is indispensable. However, Japan lacks a temperament to value original ideas and support them in positive manners. Structuring unique ideas and concepts with high originality is one of the most important intellectual production activities for human being. Understanding that these activities require incessant challenging spirit and accumulation of exhaustive efforts, a system should be structured to give the highest honor to researchers and groups who have made successes in this respect. It should be understood that development of the material technologies requires huge amount of fund, human resources and time, and national strategies should be established as required. Habitat segregation is to be moved forward in research and development, and a system will be built that links effectively the seed oriented research by universities and national research institutes with the need oriented research by business enterprises. The 21st century will be an age that many people can dream of their own success. (NEDO)

  9. Measurement results of BHTV logging at the geothermal well. 1; Chinetsusei ni okeru BHTV kenso no sokutei kekka. 1

    Energy Technology Data Exchange (ETDEWEB)

    Lin, S. [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan); Nakanishi, S.; Shimizu, I. [Electric Power Development Co. Ltd., Tokyo (Japan)

    1997-05-27

    In association with excavation of the No. 135 steam producing well in the Onikubi geothermal power plant in Miyagi Prefecture, shapes of production zones and drilling-induced fracture (DIF) were acquired from the borehole televiewer (BHTV) data. The BHTV logging shoots sound waves onto well walls of wells filled with fluid and detects the reflection waves to investigate the state of the well walls. Vertical fracture with opening lengths from 2 to 3 m were found at depths of about 1232 m and 1312 m. Water run-off has occurred at a depth of about 1312 m during the excavation, to which these vertical fractures might have contributed possibly. In depths of about 1232 m and 1312 m, fractures inclining toward north-east direction and south-west direction are predominant. Some fractures in the depth of about 1333 m incline toward east-south-east direction and west-north-west direction. Fracture inclination azimuth in all of the present logging sections is predominantly in north-east direction and south-west direction. When the DIF is considered to show the maximum compression azimuth, the earth`s crust stress azimuth is generally in east-west direction, which crosses slightly obliquely with the running direction of the predominant fracture in this well. 1 ref., 7 figs.

  10. Shallow seismic reflection prospecting in Hachiro-kata reclaimed land; Hachirogata kantakuchi ni okeru senbu hanshaho jishin tansa

    Energy Technology Data Exchange (ETDEWEB)

    Kitsunezaki, C.; Fukutome, T.; Matsumoto, S.; Noda, K.; Sato, T. [Akita University, Akita (Japan). Mining College; Hayashi, H.; Ishii, E.; Yamanaka, Y.; Matsuno, K.; Mikuni, S. [Suncoh Consultant Co. Ltd., Tokyo (Japan)

    1997-05-27

    Along the Japan Sea coast in Akita Prefecture and in the vicinity, there exist active fault groups, such as the Kitayuri thrust fault group in the south and Noshiro thrust fault group in the north. It is estimated that there is another fault, running from Akita City located between the above-said two thrust fault groups into the Hachiro-kata reclaimed land, roughly connecting the two thrust fault groups. This third fault is supposed to be related to the hypocenter of Tencho Earthquake of 830, but its location and structural configuration are not known, and it is not known whether it is an active fault, either. Investigations are conducted using S- and P-waves. The greatest problem in the use of P-waves is that there exists a layer in which signal attenuation is high and transmission is anomalously slow. This problem is ascribed to the layer pore water rendered unsaturated though slightly by the inclusion of air bubbles, and is explained for the most part by the White model. A survey using S-waves is advantageous in that it does not experience no difficulty of this kind. In the P-wave cross section, a structure supposed to be an inversion layer is observed at a level deeper than 200m. In the case of the S-wave method, more details of the shallow structure will be available when the degree of CMP stacking is augmented as usual. 2 refs., 9 figs., 1 tab.

  11. 3D seismic experiment in difficult area in Japan; Kokunai nanchiiki ni okeru sanjigen jishin tansa jikken

    Energy Technology Data Exchange (ETDEWEB)

    Minegishi, M.; Nakagami, K.; Tanaka, H. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    Difficult area in this context means an exploration-difficult area supposed to store oil/gas but retarded in exploration for the lack of knowledge about the geological structure due to poor quality of available seismic survey records. Discussed in this paper is a survey conducted into an area covering the southern part of Noshiro-shi, Akita-ken, and Yamamoto-cho, Yamamoto-gun, Akita-ken. An area size suitable for data collection at a target depth of 2500m is determined using an interpretation structure compiled on the basis of available well data and 2D seismic survey data. The plan for siting shock points and receiving points is modified case by case as restrictive factors come to the surface (resulting from the complicated hilly terrain, presence of pipes for agricultural water, etc.). The peculiarities of seismic waves in the terrain are studied through the interpretation of the available well data and 2D seismic survey data for the construction of a 3D velocity model for the confirmation of the appropriateness of the plan for siting shock points and receiving points. Efforts are exerted through enhanced coordination with the contractor to acquire data so that a technologically best design may be won within the limits of the budget. The quality of the data obtained from this experiment is in general better than those obtained from previous experiments, yet many problems remain to be settled in future studies about exploration-difficult areas. 4 refs., 4 figs., 1 tab.

  12. Relation between frequency of seismic wave and resolution of tomography; Danseiha tomography kaiseki ni okeru shuhasu to bunkaino no kankei

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, M.; Watanabe, T.; Ashida, Y.; Sassa, K. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1997-05-27

    With regard to the elastic wave exploration, discussions have been given on the relationship between frequency and resolution in P-wave velocity tomography using the initial travel time. The discussions were carried out by using a new analysis method which incorporates the concept of Fresnel volume into tomography analysis. The following two arrangements were used in the calculation: a cross hole arrangement, in which seismic source and vibration receiving points were arranged so as to surround the three directions of a region extending 250 m in the horizontal direction and 500 m in the vertical direction, and observation is performed between two wells, and a permeation VSP arrangement in which the seismic source is installed on the ground surface and receiving points installed in wells. Restructuring was performed on the velocity structure by using a total of 819 observation travel times. This method has derived results of the restructuring according to frequencies of the seismic source used for the exploration. The resolution shown in the result of the restructuring has become higher as elastic waves with higher frequency are used, and the size of the structure identified from the restructuring result has decreased. This fact reveals that sufficient considerations must be given on frequencies of elastic waves used according to size of objects to be explored. 4 refs., 4 figs.

  13. Fault analysis in the very shallow seismic reflection method. 2; Gokusenso hanshaho ni okeru danso kaiseki. 2

    Energy Technology Data Exchange (ETDEWEB)

    Nagumo, S.; Muraoka, S.; Takahashi, T. [Oyo Corp., Tokyo (Japan)

    1997-05-27

    Fault analysis is required in addition to the ordinary process of structural analysis (CDP stacking) for the examination of discontinuity in the reflection horizon in question. The fault shape restoration principle is that the reflection point of a reflection wave observed at a certain receiving point is on an ellipse with the shock point and receiving point at its focal points and that the sum of the distances between the reflection point and the focal points is equal to the reflection wave propagation time. The DMO velocity is worked out by calculation using the positive travel time and inverse travel time from the common reflection surface. When the reflection surface is inclined by {theta}, the average interval velocity/cos{theta} is called the DMO velocity. When the reflection surface inclination and the average interval velocities are determined separately in this way, the position of the reflection point may be worked out, and this enables the calculation of the amount of migration (lateral movement). The reflection wave lineups carried by the original record are picked up one by one, and the average interval velocities are treated very prudently. After such a basic DMO conversion treatment, the actualities of the fault are described fairly correctly. 3 figs.

  14. Development of GIS for feasibility study on effective use of sewage heat; Gesui netsu yuko riyo kanosei kaiseki tsuru toshite no GIS no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ichinose, T. [National Inst. for Environmental Studies, Tsukuba (Japan); Kawahara, H. [Fujitsu Facom Information Processing Corp., Tokyo (Japan); Hanaki, K. [Univ. of Tokyo, Tokyo (Japan)] Matsuo, T. [Univ.of Tokyo (Japan). Graduate School

    1996-11-22

    Water and energy in addition to matter such as products and materials from outside flowed into the urban areas, and waste, sewage, the exhausted gas and the waste heat were released into the environment as a result of the urban action. This process is called the urban metabolism analogous to the metabolism of living things. Reducing loads to environment in the urban action is nothing but to optimize the urban metabolism structures. In this study, concerning districts of the heat supply facilities to effectively reuse the heat energy obtained from sewage being a representative unused energy in urban areas, GIS was developed for conducting the analysis on the spatial conformity to reuse the waste heat in the work of head demand and heat supply. The feasibility investigation on the effective use of the sewage heat was carried out as objective examples of 23 districts in Tokyo by using this method. It was confirmed that the relationship between heat demand and supply and the amount of usable heat depended on the land use in the district. 10 refs., 12 figs., 2 tabs.

  15. On the domestic gas discrimination system by using DSP for practical use; DSP wo riyo shita kateiyo gas shikibetsu system no jitsuyoka ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Sugahara, K.; Ushio, K.; Yea, B.; Osaki, T.; Konishi, R. [Tottori Univ. (Japan)

    1998-08-31

    The structuring method for a system of discriminating domestic gas in real-time and the result of discriminating experiments performed on hydrogen gas, alcohol vapor, and cigarette smoke using the system are reported. The system takes advantage of the dependence on temperature of the response of sensor element to the kind of gas. Output signal from the sensor is discriminated by neutral network. This system has high gas selectivity for hydrogen gas, and a system with less malfunction against alcohol vapor and cigarette smoke as compared with the conventional system can be structured by utilizing the system to such domestic units as a as alarm. 128K-word memory is used for the discriminating system, and the size of program loaded in ROM is only about 7.5K words. For the ultimate system, memory may not be required to be expanded outside for the system by using on-chip memory in a digital signal processor, and smaller scale systems can be expected to be structured. 7 refs., 6 figs., 1 tab.

  16. Quality assurance in welded structures. Part 3. ; NDT technology enhanced by computer. Yosetsu kozobutsu no hinshitsu hosho. 3. ; Computer riyo ni yoru hihakai shiken no kodoka

    Energy Technology Data Exchange (ETDEWEB)

    Matsumura, H.; Ogata, T. (Kawasaki Heavy Industries Ltd., Kobe (Japan))

    1993-09-05

    The basic theory of nondestructive testing (NDT) technology enhanced by computer and its practical example are outlined. Higher reliability of the products, reduction in production cost by automation, countermeasures for dirty, hard and dangerous works, technical communication by skilled workers, and higher efficiency of the products are the principles of enhancement of nondestructive testing. The fields of application of computer to the NDT specially handy, light and cheap micro-computer are numerical analysis, drawings, image processing, automation, artificial intelligence, measurement/control, data reserve and so forth. As for the trend of NTD advancement, radiation penetrating test, automation of probe in ultrasonic flow detection or real time measurement of inspection, three dimensional graphic expression of defect results and so forth are advanced. Future topics are the normalization of appropriate thinking of quality level and improvement and clarification of reliability of NDT. 13 refs., 5 figs., 2 tabs.

  17. Survey report on the development/utilization of petroleum substitution energy in the Pacific region; Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper collected/analyzed data on petroleum substitution energy in the Pacific region. In fiscal 1996, in addition to collection of the existing energy data, conducted were collection of energy data made retroactive from 1971, and time-series collection of the energy related expanded data including energy related production statistics/social statistics, energy consumption amount by industry, power generation facilities, oil production facilities, and environmental data. As to petroleum substitution energy, the paper took up new energy such as hydroelectric, nuclear, geothermal, photovoltaic, and wind power generation, and commercial-base renewable energy. As a result of the analysis, the supply of petroleum substitution energy in the whole Pacific region has been stable, 6.6% during 1980-1990, 7.4% in the first half of the 1990s, largely over the primary energy supply. The supply of nuclear power was overwhelmingly large, followed by hydroelectric energy and geothermal/new energy. 15 figs., 23 tabs.

  18. Forward prediction of tunnel face by use of equi-traveltime planes; Tosojimen no riyo ni yoru tunnel kiriha zenpo tansa

    Energy Technology Data Exchange (ETDEWEB)

    Ashida, Y. [Kyoto University, Kyoto (Japan). Faculty of Engineering; Hirano, T. [Nishimatsu Construction Co. Ltd., Tokyo (Japan)

    1996-05-01

    The result is reported herein of a depth transform algorithm application utilizing equi-traveltime planes in reflection seismic exploration for the purpose of knowing the structure configuration in front of the tunnel face in a tunnel excavation process. A vibration producing hole was provided 0.5m above the ground surface while a vibration receiving hole was provided at 1.5m above the ground surface, and the excavated lengths were 1.5m and 0.5m, respectively. There were 24 recording channels, from which inline offset records were taken. The on-site records were subjected to 100-1000Hz band pass filtering. The elastic wave propagation rate in the rock used for depth conversion was set at 400m/s in consideration of the distance and direct wave travel time from the vibration source to the vibration receiving point. As the result of study, weak layers were found in the neighborhood of 230-240m, 260-270m, and 280-290m. This method requires less core memory for calculation and completes calculation in a shorter period of time, which enables a conclusion that it will be effective in grasping the 3-dimensional structure in front of the tunnel face in the working scene. 4 refs., 7 figs.

  19. Final report of `research on advanced uses of cast materials`; Chusho kigyo taisaku gijutsu tokubetsu kenkyu `chuzo zairyo no kodo riyo gijutsu ni kansuru kenkyu` shuryo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    Tada, S.; Takahashi, T.; Abe, T. [Tohoku National Industrial Research Institute, Sendai (Japan)

    1997-03-31

    For the advanced utilization of casting iron, temperature differential austempering and partial austempering with the gradient mechanical properties of ADI (austempered ductile iron) by local electric method were experimentally investigated. For the former, gradient mechanical properties are obtained by giving temperature difference to the material in the process of austempering of casting iron, to add the strength and toughness. For the latter, mechanical properties are controlled by repeating partial austempering with changing the isothermal transformation condition by means of local electric method, to obtain the strength characteristics with appropriate balance. As a result of the former experiment, function gradient materials could be obtained with continuously changing internal mechanical properties. The fabricated material provided different properties depending on the direction of load. Radial crushing strength constant of the ring material depended on the treatment temperature of inside surface of the specimen. Fatigue and yield strengths can be simultaneously improved. As a result of the latter experiment, it was found that the mechanical properties can be improved at arbitrary part by the partial austempering. 13 refs., 25 figs., 4 tabs.

  20. Exhaust Steam Use Cogeneration System at Ikeshima Coal Mine. The Result of Its Long Term Operation; Ikeshima tanko no hainetsu riyo kojenereshon sisutemu nochoki unten jisseki

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, Masahide. [Matsushima Coal Mining Corp., Nagasaki (Japan)

    1999-03-20

    Ikeshima Coal Mine of Matsushima Coal Mining Co., Ltd. is an undersea coal mine which established in the isolated island in the ocean. It is one of the two left coal mines in Japan. Ikeshima has started its coal production in 1959 and it has planned [D-Plant] to secure electricity for the power and water source for living and the industry. The plant was constructed in 1967. The capacity of the p;ant is 8,600kW electricity generation and 2,650 t/day evaporation and concentration multi type sea water to flesh water. For 32 years, [D-Plant] has kept generating electricity and supplying water, which is indispensable for coal mine operation and people who live in the island. (author)

  1. Study on improving efficiency in hydrogen utilizing regional heat supply system; Suiso riyo chinetsu kyokyu system no koritsu kaizen ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Sueyoshi, S.; Ishitani, H.; Matsuhashi, T. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1997-01-30

    With an objective to improve efficiency in a hydrogen energy distribution system, discussions were given on combining heat energy supply from hydrogen with factory waste heat recovery by using hydrogen absorbing alloys. This system carries out simultaneously heat supply as a result of burning hydrogen directly and heat supply obtained by converting hydrogen pressure by using hydrogen absorbing alloys. This system could allow existing gas piping facilities to be utilized. However, since quantity of hydrogen that can be transported as pressure is smaller than quantity of heat of hydrogen itself, absorption and emission are repeated a number of times in order to utilize the heat source to a possible maximum extent. Thus, a large quantity of waste heat can be utilized when this method is used. A hydrogen manufacturing system by means of LNG reformation may be combined with this heat transportation system. When waste heat that is received is handled as having zero input in the same sense as natural energy, and heat supply from a hydrogen absorbing alloy is repeated for 50 times, the overall energy balance has resulted in a considerably good value at 0.95. 5 refs., 9 figs., 5 tabs.

  2. Development of a new hydrogen purification system by using hydrogen absorbing alloy for generator cooling; Suiso kyuzo gokin riyo hatsudenkinai suiso jundo kojo system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Haruki, N.; Sato, J.; Kogi, T.; Nishimura, Y. [Kansai Electric Power Co., Inc., Osaka (Japan); Takeda, H. [Japan Steel works Ltd., Tokyo (Japan)] Fujita, T. [Mitsubishi Electric Corp., Tokyo (Japan)

    1997-05-20

    Hydrogen absorbing alloys have a number of useful functions, such as energy conversion, hydrogen storage and purification. As an application to separation and purification of hydrogen, we have developed a new hydrogen purification system by using a hydrogen absorbing alloy for generator cooling. For demonstration testing with an actual machine, a hydrogen recovery and purification device using 120kg of alloy was manufactured and installed on No.5 turbine-synchronous generator at Himeji No.2 power station. This device is designed to improve the purity of the hydrogen gas in generator containing impurities such as nitrogen and oxygen. The test results tell that the purity of the hydrogen gas in the generator can be enhanced from 98% to 99.9% and maintained at this level under continuous operation. An application of the hydrogen purification system is expected to decrease the generator`s windage loss, resulting higher generator efficiency. 2 refs., 18 figs.

  3. Survey for impacts of global environmental issues on utilization of alternative energies for oil; Sekiyu daitai energy riyo chikyu kankyo eikyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    1991-03-01

    This paper makes analyses of what policy and technological option each advanced industrial country thinks to take as measures for the global warming problem, at the same time clarifying the trends in international meetings. Analyses are also made of attitudes of developing countries and the international cooperation problem. Among the problems on global warming, an emphasis is placed on introduction of energy saving and what role the development of new energy plays. A positive group consisting mostly of West European countries is advocating a `Go Quickly` approach, while the US representing a prudent group is developing a `Go Slowly` approach. The US is considering afforestation which is useful to absorb CO{sub 2} and methane recovery as technological options. West European countries regard CO{sub 2} fixation as an important option. USSR, East European and developing countries consider that the most feasible and successful CO{sub 2} measures are energy saving/improvement of energy efficiency and forest administration/afforestation. 43 figs., 78 tabs.

  4. Survey for impacts of global environmental issues on utilizations of alternative energies for oil. Sekiyu daitai energy riyo chikyu kankyo eikyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    1990-03-01

    An analysis on the factors related to carbon dioxide (CO {sub 2} ) emissions in the past, was conducted. Then, an option menu of measures to prevent global warming including alternative energy-related ones, was discussed. In the industrial world, great contribution to increasing CO {sub 2} emissions made by the economic growth factor has been offset by CO {sub 2} reductions resulting from energy conservation and fuel switching. The Soviet/East European and the developing worlds register increasing CO {sub 2} emissions. Different countries have different views of the key option to be taken in limiting CO {sub 2} emissions. Each of currently available CO {sub 2} reduction measures has its own difficulties, and none of them is able to provide a powerful means to solve global warming problems single-handedly. To begin with, it is essential to produce time to find truly effective limiting and/or adapting measures by slowing global warming as much as possible through comprehensive strategies which call for every possible effort in all the sectors. 83 figs., 92 tabs.

  5. Utilization of coal ash from fluidized-bed combustion boilers as road base material; Sekitandaki ryudoso boiler kara no sekitanbai no robanzai to shite no riyo

    Energy Technology Data Exchange (ETDEWEB)

    Shibata, Y. [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Kozasa, K. [Center for Coal Utilization, Japan, Tokyo (Japan); Tsuzura, K. [Naruto Salt Mfg. Co. Ltd., Tokushima (Japan); Izumi, H. [Nippon Hodo Co. Ltd., Tokyo (Japan)

    1998-03-01

    Coal ash from the fluidized bed boiler is evaluated for its properties as is, as solidified or granulated, and as the roadbed material. The coal ash tested in the experiment is a mixture of ash from the fluidized bed boiler bottom, ash from the cyclone separator, and ash from the bag filter. In the manufacture of solid or granulated bodies, coal ashes are kneaded in water whose amount puts the mixture near the plasticization limit, are pressed in a low-pressure press and made into solid bodies by a 15-hour curing in 60degC saturated steam, and the solid bodies are crushed into solid granules. A content release test is conducted about the release of dangerous substances, and road paving experiments are conducted to learn the workability and serviceability of the granulated material as a road paving material. A study of the experimental results discloses what is mentioned below. Coal ash containing 10-20vol% of CaO and 15vol% or less of unburnt carbon turns into a high-strength solid after curing in saturated steam whose temperature is not higher than 60degC. The granulated solid satisfies the standards that an upper subbase material is expected to satisfy. It also meets the environmental standards in a release content test for soil set forth by Environment Agency notification No.46. 8 refs., 8 figs., 4 tabs.

  6. Effective utilization of heat from incinerating brewer prime s grains and dehydrated sludge. Beer kasu dassui odei shokyakunetsu no yuko riyo

    Energy Technology Data Exchange (ETDEWEB)

    Ogawa, T. (Asahi Breweries, Ltd., Tokyo (Japan))

    1991-02-04

    Merits of treatment cost reduction and effective utilization of waste heat were obtained through effectively utilizing the waste heat from the in-plant incineration of the brewer {prime} s grains (barley grains) generated from the brewing processes, and the dehydrated sludge generated from the waste water treatment. Keeping the pace with increase in the annual manufacturing capacity at Hakata Plant, from 60,000 kl to 180,000 kl, the brewer {prime} s grain generation has increased, but these grains have become unable to be utilized as livestock feed due to the appreciation of the yen value, hence the excess is now disposed of as wastes, causing an expense increase. Therefore, these will be incinerated together with the hydrated sludge. Because dehydrating the grains will produce fluids with high BOD value, the grains are to be burned as they are, and for this reason, a fluidized bed furnace was introduced. Effects of the incineration to the environment were surveyed, and it was confirmed that the parameters agreed with the Fukuoka Municipality can be maintained. The operation was begun in June 1989. As a result of the measures applied, an annual monetary saving of about 100 million yen can be expected out of the capital investment of 350 million yen, with the return of investment estimated to be made in about four years. 21 figs., 9 tabs.

  7. Comprehensive evaluation of biomass resources using SD method-aided world energy/land utilization model; SD shuho no sekai energy tochi riyo model ni yoru

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H. [Central Research Institute of Electric Power Industry, Tokyo (Japan); Yamaji, K. [The University of Tokyo, Tokyo (Japan)

    1996-02-01

    For the evaluation of the world-wide conflict between the utilization of biomass resources and the restrictions on land utilization, analysis was made using the system dynamics method. In the advanced area, there is scarcely any changes in land utilization, thanks to stable demand for biomass and perfect forestry protection. On the other hand, in the developing area, demand for biomass is increasing and areas of mature forests are decreasing due to imperfect forestry protection. In 2050 and after when the forests will be enjoying the same protection as that in practice in the advanced area, the forest area will stabilize. Mature forests, however, will not stop shrinking, and there will be only 400-million ha of mature forests remaining in 2100. There will be serious food shortage in the developing area because there will be a huge demand for food for livestock. Accordingly, there will be no room at all for the production of energy making crops. Both in advanced and developing areas, the potential is high of cereal residue, livestock`s dung, raw material timber residue, by-products, and refuse energy resources. On the contrary, the potential is low of kitchen refuse, paper, and chemical industry products refuse. 7 refs., 7 figs., 2 tabs.

  8. Evaluation of the performance in the solar assisted heat pump system; Taiyonetsu riyo heat pump system no seino hyoka ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Y. [Osaka Institute of Technology, Osaka (Japan)

    1996-10-27

    Performance of a solar heating system with a hydrothermal source heat pump was evaluated and compared with that of a direct solar heating system. The sun-dependency rates ({Sigma}D and {Sigma}H)of the direct system and heat pump (HP)-provided system were expressed as a function of the rate ({alpha}) of the auxiliary heat against the collected heat and as a function of the performance coefficient and {alpha}, respectively. When the sun-dependency rates are compared, it is found that the HP-provided system is the more advantageous when {Sigma}H/{Sigma}D>1. The relationship between the {alpha}`s of the two systems was clarified and computation was performed to compare the sun-dependency rates on condition that the two are equal in the heat collecting area. Although the sun-dependence rate cannot be elevated to 100% in the HP-provided system, it achieves a sun-dependency rate higher than that of the direct system even when the heat collecting area is small. In cases where the building is economically limited, for instance, with respect to the area for solar collector installation, it is advantageous to employ the HP-provided system. 5 figs., 1 tab.

  9. Performance analysis on utilization of sky radiation cooling energy for space cooling. Part 2; Hosha reikyaku riyo reibo system ni kansuru kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Marushima, S.; Saito, T. [Tohoku University, Sendai (Japan)

    1996-10-27

    Studies have been made about a heat accumulation tank type cooling system making use of radiation cooling that is a kind of natural energy. The daily operating cycle of the cooling system is described below. A heat pump air conditioner performs cooling during the daytime and the exhaust heat is stored in a latent heat accumulation tank; the heat is then used for the bath and tapwater in the evening; at night radiation cooling is utilized to remove the heat remnant in the tank for the solidification of the phase change material (PCM); the solidified PCM serves as the cold heat source for the heat pump air conditioner to perform cooling. The new system decelerates urban area warming because it emits the cooler-generated waste heat not into the atmosphere but into space taking advantage of radiation cooling. Again, the cooler-generated waste heat may be utilized for energy saving and power levelling. For the examination of nighttime radiation cooling characteristics, CaCl2-5H2O and Na2HPO4-12H2O were tested as the PCM. Water was used as the heating medium. In the case of a PCM high in latent heat capacity, some work has to be done for insuring sufficient heat exchange for it by, for instance, rendering the flow rate low. The coefficient of performance of the system discussed here is three times higher than that of the air-cooled type heat pump system. 8 refs., 5 figs., 4 tabs.

  10. Performance analysis on borehole energy storage system including utilization of solar thermal and photovoltaic energies; Taiyonetsu hikari riyo wo fukumu borehole energy chozo system no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Saito, T. [Tohoku University, Sendai (Japan); Yamaguchi, A. [Matsushita Electric Co. Ltd., Osaka (Japan)

    1996-10-27

    A permanent borehole energy storage system utilizing solar energy and waste heat from coolers is simulated, to be used as an air conditioning system for super-tall buildings. A 100m-long pipe is buried vertically into the ground, and a heat medium is caused to circulate in the pipe for the exchange of heat with the soil. Thirty borehole units are used, each measuring 9m{times}9m (with the pipe pitch being 3m). Solar cells occupying half of the wall surface facing south and solar collectors installed on the roof supply electric power and heat for cooling and warming. Heat in the ground is transferred mainly by conduction but also is carried by water and gas in movement. So, an analysis is carried out using an equation in which heat and water move at the same time. Because waste heat from cooling and warming systems is accumulated in the ground and none is discharged into the air, big cities will be protected from warming (from developing heat islands). As compared with the conventional boiler-aided air conditioning system, a hybrid borehole system incorporating solar collectors and solar cells will bring about an 80% reduction in CO2 emission and annual energy consumption. 7 refs., 3 figs., 4 tabs.

  11. Study on the detached house plan using of a maximum natural energy. Part 1; Shizen energy fukugo riyo no keikaku ni kansuru kenkyu. 1

    Energy Technology Data Exchange (ETDEWEB)

    Wada, I.; Mino, M.; Miyata, T.; Okawa, M. [Nihon University, Tokyo (Japan)

    1996-10-27

    The geographical position or environment is set on the assumption that the natural energy of a detached house is used in a hybrid state. Moreover, the energy consumption of the house and the natural energy supply obtained from the geographical position were compared and investigated. As a result, the energy consumption is 10,617 kWh, and the energy supply is 8,236 kWh. About 78% of the whole consumption can be theoretically made from natural energy. The energy supply is calculated on the low side during prediction. Therefore, an increase in the energy supply is expected by installing a solar collector based on solar energy, expanding the solar panel area, and increasing the number of wind mills. However, this energy is partially lost via an inverter while it is supplied to the general domestic equipment. At the six main points in Tokyo and its districts, the adaptability of natural energy used based on the regional characteristics is investigated presently and the installation of a system is examined. 13 refs., 2 figs., 6 tabs.

  12. Fiscal 1998 research report. Application technology of next-generation high-density energy beams; 1998 nendo chosa hokokusho. Jisedai komitsudo energy beam riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Survey was made on application technologies of next- generation high-density energy beams. For real application of laser power, application to not exciting source of YAG crystal but machining directly is highly efficient. For generation of semiconductor laser high-power coherent beam, phase synchronization and summing are large technological walls. Short pulse, high intensity and high repeatability are also important. Since ultra-short pulse laser ends before heat transfer to the periphery, it is suitable for precise machining, in particular, ultra-fine machining. To use beam sources as tool for production process, development of transmission, focusing and control technologies, and optical fiber and device is indispensable. Applicable fields are as follows: machining (more than pico seconds), surface modification (modification and functionalization of tribo- materials and biocompatible materials), complex machining, fabrication of quantum functional structured materials (thin film, ultra-fine particle), agriculture, ultra-precise measurement, non-destructive measurement, and coherent chemistry in chemical and environment fields. (NEDO)

  13. Study on data transmission method for power line maintenance information system using OPGW. OPGW riyo sodensen hoshu joho system no denso hoshiki ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Kanemaru, K.; Toyota, S. (Hitachi Cable, Ltd., Tokyo (Japan))

    1994-02-20

    Composite fiber-optic overhead ground wires (OPGWs) installed to the major power transmission lines are applied as the information transmission routs with large capacity. An effective system for the power line maintenance operation is able to be set up by using said OPGWs to collect and transmit various kinds of maintenance information on the power lines. However, since it is necessary for the whole equipment to meet the highest transmitting speed required by the system if a single transmission method is applied throughout the power lines for transmitting the maintenance information, the system loses its economy as a whole. In this paper, for the purpose of transmitting effectively the various maintenance information in power line maintenance information system using OPGWs, and considering the required transmission period as well as the types of the data occurrence, an optic fiber transmission system constituted hierarchically and composed of high-speed trunk line and low-speed local line is suggested. Especially, regarding the low-speed local lines, random transmission method shows the superior properties in the transmission efficiency and low power-consumption compared with the cyclic transmission method. 9 refs., 9 figs., 4 tabs.

  14. Research and development of system to utilize photovoltaic energy. Survey on the specific purpose modules; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoto module ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on the specific purpose modules for photovoltaic power generation in fiscal 1994. (1) On the feasibility survey on new application fields, it was clarified that photovoltaic power generation is applicable to extensive areas such as farmland, road, railway and public facility as latent demand sites. (2) On the optimum modules for various specific purposes, the structure, production method, cost estimation and issues of various modules were studied for desert, wasteland, coast, ocean, river, embankment, railway, road, mobile facility and arcade. (3) On the survey on new materials and material development, various conventional materials and materials promising for required performance were surveyed for every application. (4) On the survey on technology trends, the survey members participated in the first international photovoltaic energy conversion conference and the photovoltaic power generation workshop, while the members held the 1st-5th specific purpose module subcommittees. 1 tab.

  15. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the technology to fix and effectively use carbon dioxide using bacteria and microalgae (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of contributing to the solution to the global environmental problem, a technology is developed in which by searching for/breeding/developing bacteria, etc. which conduct photosynthesis highly effectively, CO2 is fixed and recycled. The fiscal 1996 R and D is outlined as the utilization of bacteria, microalgae, etc. Obtained were microalgae exceeding the conventional strains in CO2 fixation ability, and bacteria/microalgae excellent in production of polysaccharides, hydrocarbon, lipid, biological active substances, etc. The fundamental study was continued of CO2 integrated enzyme function/reaction system as molecular biological breeding. In the cell fusion, a set-up of conditions for green algae was started. For the confirmation of performance of high dense/quantity culture technology using solar light, further improvement of performance and systematization, 200L scale testing equipment was manufactured. It is a collective reactor and enabled study of ventilation/agitation and control of light strength. A reactor analysis model was constructed. Also including the conversion into useful substances, energy/material balance was systematically studied. Collection of technical literature and information exchanges were made in Japan and overseas. 276 refs., 475 figs., 156 tabs.

  16. FY 1997 report on the results of the industrial technology R and D project. Development of technology to use biological resources such as the complex biological system (Development of biological use petroleum substitution fuel production technology); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Experimental researches were conducted and the FY 1997 results were reported with the aim of establishing analytical technology for the complex biological system by which the complex biological system can be analyzed in such a state as it is using the molecular biological method. In the study of the molecular genetic analytical technology, PCR primers used for amplification of topoisomerase II genes of the whole eukaryote was designed. As to the histochemical analytical technology, a study was made on the new constitution microorganism detection method by the hybridization method and the antibody specific dyeing method, and the following were conducted: manifestation in quantity of colibacillus and the recovery, refining, and construction of peptide library by fuzzy display method. Concerning the functional analytical technology, technological researches were made such as the environmental adaptation mechanism of high thermophile and the information transfer mechanism among bacteria through cell membranes for elucidation of the special environment detection/response mechanism and the special environment adaptation/resistance mechanism. As to the separation/culture technology, various anaerobic microorganisms were separated from marine sponge for the development of a method of culturing in 3D matrices. (NEDO)

  17. FY 1998 R and D of utilization of biological resources such as those in bioconsortia. Report on development results of techniques for utilization/production of organisms in bioconsortia; 1998 nendo fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The objectives are set to analyze functions and interactions of organisms having specific functions, to develop the techniques for isolating and cultivating the constituent organisms, and thereby to develop the techniques for their industrial utilization, in order to develop the techniques for handling organisms in bioconsortia as the techniques to utilize their functions, e.g., production and decomposition of materials, and also to develop the techniques for culturing/controlling microorganisms in bioconsortia and for strengthening their functions. The FY 1998 themes are development of the functional material production technology, and comprehensive study for the project. More concretely, the former includes histochemical analytical technology (development of techniques for detecting microorganisms in soil, and of techniques for in-situ detection/isolation of specific microorganisms in bioconsortia and for analysis their functions), isolation and culture technology (development of detection, separation and cultivation technology of microorganisms that are not easily cultured), functional substance production technology (technical utilization of microbial consortia for production of environment-friendly oil/water separation polymers), and functional material production technology (development of methods for artificial gene exchange in microbial consortia). (NEDO)

  18. Industrial science and technology research and development business for fiscal 1998. Research and development achievement report on glycoconjugate production and utilization technologies (Development of technologies of glycoconjugate-aided CO{sub 2} fixation and utilization); 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu seika hokokusho (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Enzymatic and chemical methods were combined and methods were developed for synthesizing mucin type sugar chains and glycopeptides. The influence of sugar chain positions and structures on glycoconjugate stereo structures and physiological activities was analyzed, and glycopeptide structural activities and glycoconjugate remodelling were studied. To create an industrial advantage in a glycoprotein production system by use of zooblasts, sugar chain structure control through sugar transfase occurrence control was studied. For the production of man-adaptive sugar chains using yeast, new yeast variations were subjected to molecular breeding, and tested for the resultant improvement on productivity. Sugar chain marking and refining techniques and various responding mechanisms on the solid surface were elucidated, which enabled structure analyses using sugar chain recognition molecules such as lectins and antibodies. A database on interactions between sugar chains and sugar chain recognition molecules was constructed using the said findings. An analyzing program was also formulated tentatively. This paper also covers general surveys and studies on technologies of producing and utilizing glycoconjugates. (NEDO)

  19. Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of technologies for producing substitute fuel for petroleum by utilizing organisms; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Technologies of producing useful substances using the substance decomposing/producing functions of complex biosystems and methods of their handling are developed. In the utilization of microbes in the digestive tracts of termites and longicorns, it is made clear that several kinds of termites cleave the {beta}-O-4 ether linkage. In relation to technologies for wood decomposing complex microbial system construction and complex vector system development, a screening system is constructed in which strains that exhibit complex actions are combined. Concerning the advanced utilization of tropical oil plants, conditions are determined for inducing callus out of oil palm tissues. Out of oil palm sarcocarp tissues, mRNA (messenger ribonucleic acid) is isolated for the construction of a cDNA (complementary deoxyribonucleic acid) library. For the purpose of isolating a powerful promoter, a partial base sequence is determined for ubiquitin that frequently expresses itself in cells. A pathogenic bacterium ailing the oil palm is sampled for identification, and it is inferred that the bacterium is a kind of Ganoderma boninense. (NEDO)

  20. FY 1999 report on the results of the R and D of the global environmental industry technology. R and D of the CO2 fixation/effective use technology using bacteria/algae; 1999 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing the technology to fix CO2 and recycle it as resource in higher efficiency than that in photosynthesis in the nature world, study of bacteria, etc. was made in terms of the search, breeding, and artificial realization of the growth environment, etc. The FY 1999 results were summed up. As to high efficiency photosynthetic bacteria/microalgae, conditions for sampling/breeding/optimum culture of bacteria were established and made database. From conditions for the optimum CO2 fixation by photosynthetic bacteria, oxygen injury prevention culture method, continuous culture experiment, etc., it was found out that the carbyne cycle was a main route of the carbon fixation also in photosynthetic bacteria. As to the cell fusion, established were the technology of electric fusion of interspecific fusion strains and the technology of evaluation of growth characteristics. Also studied was a method to transfect genes into Chlorella sp. which fixes CO2. Concerning the light collecting reactor of 200L scale, a high concentration culture experiment was carried out using Chlorella sp. UK001 as the strain tested, and the engineering data on the behavior in culture tank, multiplication speed, etc. were collected. (NEDO)

  1. Industrial technology research and development project for global environment in fiscal 1998. Report on achievements in research and development of technologies for fixation and effective utilization of carbon dioxide by utilizing bacteria and algae; 1998 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Microorganisms are cultivated industrially in a great quantity to fix CO2 at efficiency higher than that of photosynthesis in natural world to develop technologies to re-utilize them as resources. This paper describes achievements in fiscal 1998. Existing strain samples of photosynthesized bacteria and micro-algae were screened to continue discussions on optimal culture conditions, and evaluation on properties. Genes that provide Chlorella with antibiotic resistance were introduced to have performed evaluation on function manifestation, and acquired enzymatic genes of unsaturated {omega} 3. Using green algae as the object, reduction in the processing time has resulted in acquiring a large number of fused cell colonies. Discussions were given on conditions to breed photosynthesized bacteria and fix CO2. Structural analyses were performed on CA protein as an enzyme related to take CO2 into living organisms, and on genes. Developments were carried out on a photosynthesizing bio-reactor and useful substance producing technologies on a continual basis. A 200-liter scale light collection type bio-reactor improved the fixing capacity by 30% in Chlorellas by changing the culture medium. The direct light receiving panel type bio-reactor can utilize even scattered light, with its fixing capacity per installation area exceeding the target. Fundamental data were acquired with Chlorellas on utilizing feeds, fertilizers and building materials. (NEDO)

  2. Fiscal 1997 survey report. Subtask 7 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (survey/study on the hydrogen utilization technology); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 7 suiso riyo gijutsu ni kansuru chosa kento

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the 1997 results of the survey/study of the hydrogen utilization technology. As to the power generation system, trially calculated were effects of oxygen purity on efficiency of the argon circulating hydrogen diesel cogeneration, and the power generating efficiency in case of considering power separating oxygen from air. It was found that the power generating efficiency equal to or more than that of the existing diesel can be expected. In relation to means of transportation, the introduction was studied of hydrogen engine family cars and hybrid fuel cell micro-buses. Concerning oxygen/hydrogen use fuel cells, discussed was the power generation using fuel cells by night power use electrolytic hydrogen/oxygen production as well as fixed 200kw and 5000kw class fuel cells and three automobile use polymer fuel cells. As to the hydrogen supply system in model cities, studied were the control of boil-off gas generation and the effective use of the gas, the hydrogen receiving base, and a scenario for shifting to hydrogen energy systems. For a realistic shift to the hydrogen energy society, discussed was a standalone hydrogen supply station. 24 refs., 130 figs., 57 tabs.

  3. FY 1998 industrial technology R and D project. Report on the results of the development of utilization technology of biological resource such bioconsortia system (Development of production technology of biological use petroleum substituting fuels); 1998 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu (seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Technology development was conducted for production of useful substances using the bioconsortia system. In FY 1998, the development of element technology was studied. As to the utilization technology of gut symbiotic microorganisms such as termite and longhorn beetle, clone types of gut microorganism complex system were analyzed to find out the diversification. In the decay of wood, co-culture of two species of mold fungus was increased in efficiency than single culture. More than 90% was classified/identified of the mold fungi accumulated (in wood piece)/separated for the utilization of plant symbiotic microorganisms. For the production of petroleum substituting useful resource, conditions were established of callus induction from immature embryos of tropical oil crops, especially oil palm, and of regeneration of a lot of small plants from the callus. To establish the Agrobacterium-mediated transformation system of oil palm, the binary vector harboring the reporter gene and selectable marker gene was constructed. Using the vector, oil palm tissues are inoculated and infected with agrobacteria. To heighten the function of palm oil, 10 particular clones were selected from the complementary DNA library obtained from oil palm fruit tissues. The genetic study of germs was also made. (NEDO)

  4. Improvement of liquefaction solvent. Increase of light oil yield with a reduction in catalyst addition; Ekika yozai no kairyo kenkyu. Sekitan ekikayu no keishitsuka to shokubai tenkaryo no teigen

    Energy Technology Data Exchange (ETDEWEB)

    Okuyama, N.; Yasumuro, M.; Sato, K.; Komatsu, N.; Okui, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

    1996-10-28

    For developing coal liquefaction processes, it is an important problem to improve the light oil yield with increased oil yield. It was previously reported that distillate mainly containing lighter fraction can be produced with high oil yield by reducing the iron/sulfur catalyst addition in slurry, by recycling gas in the process operation, by utilizing these effects, and by using heavy oil as recycling solvent. In this study, the maximum distillate yield of Victorian brown coal was investigated through continuous liquefaction using a bench scale unit. In addition, operation conditions for obtaining sufficient oil yield were investigated under the reduced catalyst addition into one-third. Consequently, it was confirmed that the maximum content of lighter fraction in distillate product was obtained with reduced catalyst addition by using heavy oil as recycling solvent, by adopting new catalyst, and by utilizing effects of CLB recycling and gas recycling in maximum. It was also revealed that lighter distillate can be produced compared with the oil product obtained by recycling conventional solvent. 3 refs., 6 figs., 2 tabs.

  5. Thermal relaxation of bituminous coal to improve donation ability of hydrogen radicals in flash pyrolysis; Sekitan kozo kanwa ni yoru suiso radical kyoyo noryoku no kojo wo mezashita netsubunkai mae shori

    Energy Technology Data Exchange (ETDEWEB)

    Mori, T.; Isoda, T.; Kusakabe, K.; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hayashi, J. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    In terms of coal conversion reaction, the behavior of bituminous coal heated beyond a glass transition point was examined on the basis of pyrolyzed products, and the effect of an increase in proton mobility on promotion of coal decomposition was evaluated. In experiment, after Illinois bituminous coal specimen was heated up to a specific temperature in N2 or He gas flow at a rate of 5K/min, the specimen was directly transferred to a pyrolyzer for instantaneous pyrolysis. As the experimental result, the glass transition temperature of the Illinois coal specimen was calculated to be 589K from a differential scanning calorimetry (DSC) profile. From the pyrolysis result of the Illinois coal specimen heated up to 623K, the char yield decreased by 3kg as compared with that of the original coal, while the tar yield increased by 4kg up to 27kg per 100kg of the original coal. This tar increase was larger than that of cooled coal. These results suggested that the donation of hydrogen radicals to coal fragments is improved with an increase in proton mobility. 4 refs., 4 figs., 1 tab.

  6. Studies of initial stage in coal liquefaction. Effect of prethermal treatment condition with process solvent to increase oil yields; Ekika hanno no shoki katei ni kansuru kenkyu. Sekitan no maeshori joken to yozai koka

    Energy Technology Data Exchange (ETDEWEB)

    Shindo, T.; Komatsu, N.; Kishimoto, M.; Okui, T.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. ltd., Tokyo (Japan)

    1996-10-28

    Process solvent was hydrogenated in the brown coal liquefaction, to investigate the influence of it on the prethermal treatment and liquefaction. Consequently, it was found that the n-hexane soluble (HS) yield was improved. In this study, capacity of hydrogen transfer from solvent during prethermal treatment and effects of catalyst were investigated. Since prethermal treatment in oil was effective for improving the oil yield in the presence of hydrogen/catalyst or high hydrogen-donor solvent, influence of hydrogen-donor performance of solvent or addition of catalyst on the hydrogenation behavior of coal and the characteristics of products during prethermal treatment were investigated in relation to successive liquefaction results. As a result, it was found that the increase of HS yield was due to the acceleration of conversion of THF-insoluble using high hydrogen-donor solvent and/or by adding catalyst. It was also found that the use of high hydrogen-donor solvent and highly active catalyst at the stage of prethermal treatment before the successive liquefaction was effective for improving the HS yield, i.e., liquefied oil yield. 2 refs., 5 figs., 1 tab.

  7. Relations between flash pyrolysis reactivity and oil/gas products from coals of different rank; Sekitankado no kotonaru shushu no sekitan no flash pyrolysis hannosei to gas oyobi eki seiseibutsu no kankei

    Energy Technology Data Exchange (ETDEWEB)

    Nonaka, T.; Kishino, M.; Sakanishi, K.; Korai, Y.; Mochida, I. [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study

    1996-10-28

    Curie point flash pyrolysis (FP) reactivity was studied experimentally using three kinds of coals with different coal ranks such as Yallourn brown coal, Tanitoharum sub-bituminous coal and Wandoan sub-bituminous coal. Experiment was performed using a curie point pyrolyzer in carrier gas of 20ml/min in gas flow rate at 450, 590 and 740{degree}C for 5sec. The experimental results were as follows. Each gas component obviously increased at 450-590{degree}C, however, C4-C6 gases drastically decreased at 590-740{degree}C accompanying reduction of the whole gas quantity. All of each polar component remarkably increased at 450-590{degree}C. Yallourn brown coal with high Owt%, in particular, contained a large amount of alkyl-hydroxybenzene group. The amount of cresol of all of three coal specimens also increased at 740{degree}C. It was thus suggested that this is coal constituent molecules derived from cutting of methylene-ether bridged bond by higher-temperature FP. 8 refs., 5 figs., 3 tabs.

  8. BTX production by in-situ contact reforming of low-temperature tar from coal with zeolite-derived catalysts; Zeolite kei shokubai wo mochiita sekitan teion tar no sesshoku kaishitsu ni yoru BTX no seisei

    Energy Technology Data Exchange (ETDEWEB)

    Matsunaga, T.; Fuda, K.; Murakami, K.; Kyo, M.; Hosoya, S.; Kobayashi, S. [Akita University, Akita (Japan). Mining College

    1996-10-28

    On BTX production process from low-temperature tar obtained by pyrolysis of coal, the effect of exchanged metallic species and reaction temperature were studied using metallic ion-exchanged Y-zeolite as catalyst. In experiment, three kinds of coals with different produced tar structures such as Taiheiyo and PSOC-830 sub-bituminous coals and Loy Yang brown coal were used. Y-zeolite ion-exchanged with metal chloride aqueous solution was used as catalyst. Zn{sup 2+}, Ni{sup 2+} and In{sup 3+} were used as metal ions to be exchanged. The experiment was conducted by heating a pyrolysis section up to 600{degree}C for one hour after preheating a contact reforming section up to a certain proper temperature. As a result, the Ni system catalyst was effective for BTX production from aromatic-abundant tar, while the Zn system one from lower aromatic tar. In general, relatively high yields of toluene and xylene were obtained at lower temperature, while those of benzene at higher temperature. 4 figs., 1 tab.

  9. Effect of coal rank and mineral matter on gasification reactivity of coal char treated at high temperature; Netsushorishita sekitan char no gas ka tokusei ni taisuru tanshu oyobi kobutsushitsu no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Morishita, K.; Takei, H.; Harano, A.; Takarada, T. [Gunma University, Gunma (Japan). Faculty of Engineering

    1996-10-28

    In the wide range from brown coal to anthracite, an investigation was made of effects of heat treatment on physical/chemical properties and of coal rank dependence. For the experiment, 12 kinds of coal samples were used, and for heat treatment, the fluidized bed heated by the electric furnace and the infrared-ray gold image furnace were used. To examine characteristics of the heat-treated coal char, conducted were oxygen gasification, TPD measurement, XRD measurement, alkali metal measurement, and pore distribution measurement. The following were obtained from the experiment. The gasification reaction rate of the char heat-treated in the temperature range between 900{degree}C to 1700{degree}C decreases with a rise of the temperature of heat treatment, and the degree of decrease in the rate depends on coal rank. The order of gasification rate between coal ranks depends on the temperature of heat treatment, and the lower the heat treatment temperature is, the more largely the gasification rate is influenced by catalysis of mineral matters included in the coal. As causes of the decrease in gasification rate associated with the rise in temperature of heat treatment, indicated were release of alkali metal having catalysis and decrease of active sites by carbonaceous crystallinity. 6 figs.

  10. Fiscal 1998 overseas geological structure survey. Japan-China joint coal survey Mei-Xian project; 1998 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Mei-Xian project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Japan-China joint coal survey was made through seismic prospecting by Japanese group and drilling prospecting by Chinese group. Mei-Xian mine property includes coal seams of the Jurassic period, and is covered with the quaternary period stratum without any coal seam. The base of the quaternary period stratum exists at depth of 50-400m, while the coal seams at depth of 300-700m. Among 11 existing seams, the 1st and 5th seams are main objects for prospecting. The 5th seam of 0.2-8.96m (2.95m in average) thick is the most expected important one, distributing all over the mine property. The 5th seam also has branch seams spreading over 2.5km from east to west and 1.2km from south to north in the center part of the mine property. The 1st seam of 0-8.62m (2.90m in average) thick is most thick in the south part of the mine property. The theoretical amount of coal deposits in the whole coal seam is estimated to be nearly 290,000,000t by Chinese group (nearly 50% of it in the 5th seam). That is also estimated to be nearly 346,000,000t by Japanese group (155,000,000t in the 5th seam). Both 1st and 5th seams are composed of sub-bituminous coal. (NEDO)

  11. Fiscal 1997 report on the survey of overseas geological structures, `the Tanjungenim Coal Exploration Project between Japan and Indonesia`; 1997 nendo kaigai chishitsu kozonado chosa `Nippon Indonesia sekitan kyodo tansa Tanjungenim project`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The basic survey for coal mine development was conducted in the Banjarsari area of Tanjungenim, Sumatra, Indonesia. In the survey, Japan deals with ground surface exploration, borehole physical survey, VSP survey and seismic survey, and Indonesia exploratory drilling, topographical mapping, measurement, hydrologic/hydraulic survey, access road formation, etc. The boreholes drilled are 35 in number and 4004m in total drilling length. The borehole physical survey was conducted in all 35 holes. The seismic survey was conducted on 5 traverse lines and in a total length of 10.19km, and the VSP survey in two boreholes. As a result of the survey, it was found out that there existed a large amount of coal reserve in a comparatively shallow area in the south-central part of the Banjarsari area. There exist faults, which has no great effects on the open pit mining. There is a high possibility of developing large-scale coal mines of open pit mining type with a comparatively low soil removing ratio. Concerning the coal quality, the heating value is comparatively low, the latter half of a 4000 kcal/kg level. It can be expected to realize a pit-mouth power plant which is low in coal carrying cost. 129 figs., 28 tabs.

  12. Basic surveys for developing coal resources in fiscal 1989. A report on re-analysis of on-shore physical exploration in the Ariake sea area; 1989 nendo sekitan shigen kaihatsu kiso chosa. Ariakekai chiiki kaijo butsuri tansa saikaiseki hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    The present survey was intended to enhance accuracy of analysis and interpretation of the geological structures in the northern and north-western parts of this area, and the status of coal seam existence. The survey used the most part of the earthquake exploration data obtained in fiscal 1988, and parts of the earthquake exploration data obtained in fiscal 1983 and fiscal 1985 in the vicinities thereof, and incorporated a new treatment method to perform re-analysis. The quaternary deposit seam has thickness of 80 to 610 m, and the Palaeogene deposit seam has thickness of 600 to 1600 m as a whole. The structure of the foundation bed is nearly parallel with the structure of the top of a coal seam in the Palaeogene deposit seam, having a distance of 300 m between the seams. The surveys combining the test drillings having been done to date and the physical exploration estimates that the coal seam groups are distributed over the entire area of Ariake Sea. Possibility has heightened, that the coal seam groups may spread over the land area. The collapsed fault passing east-west the northern most area of the Ariake Sea and having drop of 200 to 300 m forms the northern boundary of the Miike coal field. However, the coal seam groups are estimated to spread north of the coal field as a sedimentary basin, and continue to the northern side of the fault. (NEDO)

  13. Estimation of water-coal surface interaction during heat treatment of coal by use of FTir and DSC; FTir to DSC wo mochiita sekitan-mizu kan sogo sayo no teiryoteki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Miura, K.; Mae, K.; Morozumi, F.; Kusakawa, T. [Kyoto University, Kyoto (Japan)

    1997-10-30

    The authors have recently presented a method to estimate the strength distribution of hydrogen bondings in coal using FTir and DSC. The method was applied to estimate the strength of coal-water interaction in two different coals and to estimate the enthalpy change deriving from the change in hydrogen bondings during the desorption of water. The estimated enthalpy change was compared with the total enthalpy change estimated by DSC measurement to examine the importance of hydrogen bondings during the desertion of water. 1 ref., 6 figs.

  14. Fiscal 1993 survey of the base arrangement promotion for foreign coal import. Survey of the general situation of Thai coal; 1993 nendo kaigaitan yunyu kiban seibi sokushin chosa. Thai sekitan sogo jijo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The paper reported the energy situation in Thailand, the present and future status of coal supply/demand, the present situation of environmental policy and air pollution prevention policy and problems concerning coal and the measures for solution, and a possibility of Japan`s cooperation. In Thailand, the total coal supply amount in 1992 is 16.079 million tons, which is 9.1% of all the primary energy supply amount. The country produces only a few amount of anthracite and subbituminous coal beside brown coal. The domestic coal equals brown coal, the production of which was 15.335 million tons in 1992, 13.9% of all the primary energy demand. Concerning brown coal, 79.7% of all the brown coal supply are for electric power use, and others for industrial use such as the cement industry. The remaining reserve in developed areas is 151.4 billion tons, and the proven reserve in undeveloped areas 756 million tons. The demand for import coal was 11.25 million tons in 1996, and is expected to be 201.73 million tons in 2000. The paper pointed out some problems arising from coal production and spread of coal utilization, and described measures to solve the problems and fields where there are possibilities of Japan`s cooperation. 36 refs., 44 figs., 73 tabs.

  15. Wakamatsu high-temperature turbine verification test project; Study of a large capacity coal fired USC plant. Wakamatsu chokoon turbine jissho shiken project; Taiyoryo sekitan fun chocho rinkai atsu plant no jitsugen wo mezashite

    Energy Technology Data Exchange (ETDEWEB)

    Furuya, K. (Electric Power Development Co. Ltd., Tokyo (Japan)); Hizume, A. (Kobe Univ., Kobe (Japan). Faculty of Engineering); Fujikawa, T.; Yokota, H.; Kokubu, T.; Takeda, Y. (Mitsubishi Heavy Industries Ltd., Tokyo (Japan))

    1990-12-25

    The ultrasupercritical (USC) power generation system, which intends to improve efficiency by elevating temperature and pressure of thermal power plants, is one of promising systems utilizing effectively coal whose reserve is abundant. In this report, concerning the project to generate power actually by modifying the already installed Wakamatsu No.2 75MW turbine of the Electric Power Development Public Corporation (EDPC) to a 50MW ultra high temperature turbine, by manufacturing newly a HP-IP combined element of the Wakamatsu No.2 turbine and installing it in lieu of the old one and using its LP element as is, the design of the turbine and the operation result at the Step I of its two staged basic steam conditions are, inter alia, reported. For the Wakamatsu ultra high temperature turbine modelling after the VHP element of a 1000MW USC turbine, the new materials and new designs which were developed in order to meet the specifications of each section obtained through the concept design of a 1000MW USC turbine were adopted. The Step I (main steam/reheating temperature 593/593 centigrade) has been operated continously very well since 1986. 14 refs., 20 figs., 5 tabs.

  16. Development of coal liquefaction technologies (Part 3); Development of common base techniques (Part 4). Development and employment of evaluating approach to liquefied process. Development of data collecting and processing system for coal liquefaction process and etc. Sekitan ekika gijutsu kaihatsu (3); Kyotsu kiban gijutsu no kaihatsu nado (4). Ekika process no hyoka shuho no kaihatsu, unyo. Sekitan ekika process nado no data no shushu, Shori system

    Energy Technology Data Exchange (ETDEWEB)

    1989-09-01

    This research aims to develop the management system of informations concerning coal liquefaction process and etc., to develop data collecting and processing system on pilot plant and supporting researches and to effectively use data to advance to following step such as conceptural design for the demonstration plant. In addition, this research aims to collect many kinds of techniques obtained by the research and development and to arrange and promote the licensing system to practically use this system. Practical results in 1988 were as follows: Conceptural design on basic data base and retrieval or look up system on general technical informations were carried out to develop the data base system for coal liquefaction and to develop the data collecting and processing system for the coal liquefaction process and etc. Data locative leveling was carried out as the conceptural design for basic data base and the basic structures of hardware and software were made up as the basic design for the retrieval system of general technical informations. 4 figs., 1 tab.

  17. Burning-off characteristics of carbon fibers by joule heating in air; Tanso sen`i no taikichu ni okeru tsuden shodan

    Energy Technology Data Exchange (ETDEWEB)

    Endo, M.; Takeuchi, K.; Nishimura, Y.; Kasai, T. [Shinshu University, Nagano (Japan). Faculty of Engineering

    1996-02-26

    This paper evaluates the burning-off performance of mesophase pitch-based carbon fibers (MPCFs) by joule heating in air. The MPCFs have higher current capacity up to burning-off by joule heating than copper wires, and can be proof against large current. Especially, the current performance of MPCFs is roughly divided into two groups based on the degree of graphitization, which reflects difference in the crystal structure. While, the pitch-based activated carbon fiber (ACF) having very fine pores and huge specific surface is very weak against the electrical applications. For the observation of burned-off fibers by FE-SEM, inherently emphasized current applied structures reflecting original structures, such as the layered structure of MPCF and the pore structure of ACF were observed. Consequently, it was suggested that the carbon fibers themselves can be proof against severe conditions for their electrical applications. It was also concluded that the fiber structure formed by burning-off is one of useful methods for characterizing various structures of carbon fibers. 21 refs., 8 figs., 2 tabs.

  18. Energy consumption and human factors. Residents` style of living and consciousness of the residential houses; Energy shohi to human factor. Jutaku ni okeru kyojusha no ishiki sumaikata

    Energy Technology Data Exchange (ETDEWEB)

    Matsubara, N. [Kyoto Prefectural Univ., Kyoto (Japan). Faculty of Living Science

    1996-09-05

    Energy consumption and human factors, which mean residents` style of living and consciousness of the residential houses, are considered on the basis of the survey results for residents living in residential houses with the same specifications in the Kansai district in 1994. The outside climate condition is loosened through the shelter performance of building, solar radiation, and clothes, to form the climate under clothes. Additionally, as a result of physiological control of body heat, the warm, cool, and comfortable sensations are formed. Various factors affect this process. Conception of satisfaction was considered as upper criteria. There are residents satisfying the non-use of air-conditioner, even though it is not comfortable. The concept of satisfaction determines dissatisfaction, patience, and otherwise satisfaction of environment modification action and escape action from environment. Concrete examples of the life style are illustrated based on the survey. Dispersion of room temperature and the various consciousness and styles of living are also illustrated, qualitatively, on the basis of the field survey. For the investigation of domestic energy consumption items, it is not avoidable to illustrate the common actual conditions of living. 12 refs., 2 figs., 1 tab.

  19. Cyanide formation by the cyanide distillation of nitrate. Zen shian joryuji ni okeru shosan ion ga kanyosuru shian kagobutsu ion no seisei

    Energy Technology Data Exchange (ETDEWEB)

    Ogura, H. (The Chiba Prefectural Lab. of Water Pollution, Chiba (Japan))

    1994-06-10

    Cyanide ion is formed by reacting disodium ethylenediamine-tetra-acetate (EDTA) with a sample containing nitrous ion. Further, it is known that cyanide ions are also generated from the reaction between EDTA and the product of the reaction of oxide and the substance like hydroxyl ammonium chloride which is added to reduce the oxide contained in the sample. In the present researches, the possibility of the formation of cyanide ions from the nitric acid used popularly in the manufactory of plating and surface-treatment is examined. It is expected that if nitric ion takes a part in the formation of cyanide ion, the reaction reducing the nitric ion into nitrous ion would happen as the former step thereof. Therefore, the cyanide distillation of nitric ions co-existing with the reducing agent is carried out, and it is confirmed that cyanide ion is formed with the participation of EDTA. 14 refs., 1 fig., 7 tabs.

  20. Calculation of wave resistance by using Kochin function in the Rankine source method; Rankinsosuho ni okeru kochin kansu wo mochiita zoha teiko keisan

    Energy Technology Data Exchange (ETDEWEB)

    Yasukawa, H. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1997-10-01

    In order to avoid negative wave resistance (which is physically incomprehensible) generated in calculating wave resistance by using the Rankine source method, a proposal was made on a wave resistance calculation method using the Kochin function which describes behavior of speed potential in regions far apart from a hull. The Baba`s condition was used as a free surface condition for the speed potential which expresses wave motions around a hull. This has allowed a new Kochin function which uses as unknown the speed potential on the hull surface and the free surface near the hull to be defined and combined with the Rankine source method. A comparison was made between the calculated values for wave resistance, hull subsidence and trim change of an ore transporting vessel (SR107 type of ship) in a fully loaded condition and the result of water tank tests. The wave resistance values derived from pressure integration have all become negative when the Froude number is from 0.1 to 0.2, while no negative resistance has appeared in the calculations by using the Kochin function, but the result has agreed with that of the water tank tests. Accuracy of the calculations at low speeds was improved. The trim change in the calculations was slightly smaller than that in the water tank tests. The subsidence showed a good agreement. 7 refs., 1 fig.

  1. Characteristic analysis of turbulent heat diffusion in a multi-compartment structure; Takukakuka kukan kozo ni okeru ranryunetsu kakusan gensho no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Hu, C.; Fukuchi, N. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-10-01

    An analysis was made on turbulent heat diffusion in a multi-compartment structure necessary for designing calorific power and environment for functional systems used in marine vessels and off-shore structures. In a multi-compartment structure, the diffusion phenomenon is complex because of movement of air flow in turbulence and buoyancy resulted from non-isothermal condition. The phenomenon is largely affected by space shapes and walls, and the conditions in heat diffusion field is governed also by shapes of opening connecting the compartments. An analysis was made by using the SIMPLE method on turbulent heat diffusion in a multi-compartment space with high Raleigh number in which natural convection is dominant. If the opening is small, the Coanda effect appears, in which air flow passing through the opening rises along the wall, wherein a high-temperature layer is formed near the ceiling, making the heat diffusion inactive. If the opening is large, a jetting flow from the opening and a large circulating flow are created, which cause active advection mixture, making temperature gradient smaller in the upper layer. Heat transfer intensity in an opening on a partition wall decays in proportion with 1/4th power of the opening ratio. 7 refs., 11 figs.

  2. Nonlinear process generating Tollmien-Schlichting waves in a reattached boundary layer; Hakuri saifuchaku nagare ni okeru T-S hado no hisenkei reiki katei

    Energy Technology Data Exchange (ETDEWEB)

    Asai, M.; Aiba, K. [Tokyo Metropolitan Institute of Technology, Tokyo (Japan)

    1995-09-01

    Low-frequency Tollmien-Schlichting (T-S) waves may be thought generated as a result of high-frequency disturbance between two proximity frequency modes grown unstably in a separation shear layer causing secondary nonlinear interference to occur. This fact has been verified by a numerical simulation. A non-compression Navier-Stokes equation was used for the fundamental equation, a tertiary windward difference for the convection term, and a secondary central difference for other differential calculus. The Reynolds number was 200, and the disturbance was introduced by applying `v` variation continuously on the wall face. Non-introduction of the disturbance results in a steady flow. Disturbance frequencies of 0.15 and 0.20 were selected as disturbance frequencies from the relationship between the spatial amplification and the frequency dependency. The structure of the excited disturbance agreed with the intrinsic mode. The difference mode due to nonlinear interference grows as the basic mode was amplified. The basic mode decays sharply in the boundary layer after reattachment, while the difference mode decays slowly. Distribution of the difference mode is a distribution of viscous T-S waves, which may be converted into the intrinsic mode. 8 refs., 7 figs.

  3. Photo-irradiation effects on GaAs atomic layer epitaxial growth. GaAs no genshiso epitaxial seicho ni okeru hikari reiki koka

    Energy Technology Data Exchange (ETDEWEB)

    Mashita, M.; Kawakyu, Y.; Sasaki, M.; Ishikawa, H. (Toshiba Corp., Kawasaki (Japan). Research and Development Center)

    1990-08-10

    Single atomic layer epitaxy (ALE) aims at controlling a growing film at a precision of single molecular layer. In this article, it is reported that the growth temperature range of ALE was expanded by the vertical irradiation of KrF exima laser (248 nm) onto the substrate for the ALE growth of GaAs using the metalorganic chemical vapor deposition (MOCVD) method. Thanks for the results of the above experiment, it was demonstrated that the irradiation effect was not thermal, but photochemical. In addition, this article studies the possibility of adsorption layer irradiation and surface irradiation as the photo-irradiation mechanism, and points out that coexistence of both irradiation mechanisms can be considered and, in case of exima laser, strong possibility of direct irradiation of the adsorption layer because of its high power density. Hereinafter, by using both optical growth ALE and thermal growth ALE jointly, the degree of freedom of combination of hetero ALE increases and its application to various material systems becomes possible. 16 refs., 6 figs.

  4. Vortex-induced vibrations of circular cylinder in cross flow at supercritical Reynolds numbers; Chorinkai Reynolds su ryoiki ni okeru enchu no uzu reiki shindo

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, T.; Nakao, T.; Takahashi, M.; Hayashi, M.; Goto, N. [Hitachi, Ltd., Tokyo (Japan)

    1999-07-25

    Vortex-induced vibrations were measured for a circular cylinder subjected to a water cross flow at supercritical Reynolds numbers for a wide range of reduced velocities. Turbulence intensities were changed from 1% to 13% in order to investigate the effect of the Strouhal number on the region of synchronization by symmetrical and Karman vortex shedding. The reduced damping of the test cylinder was about 0.1 in water. The surface roughness of the cylinder was a mirror-polished surface. Strouhal number decreased from about 0.48 to 0.29 with increasing turbulence intensity. Synchronized vibrations were observed even at supercritical Reynolds numbers where fluctuating fluid force was small. Reduced velocities at which drag and lift direction lock-in by Karman vortex shedding were initiated decreased with increasing Strouhal number. When Strouhal number was about 0.29, the self-excited vibration in drag direction by symmetrical vortex shedding began at which the frequency ratio of Karman vortex shedding frequency to the natural frequency of cylinder was 0.32. (author)

  5. Energy conservation progress in building equipment. Energy conservation on the sports facilities; Kenchiku setsubi ni okeru sho energy no shiten. Supotsu reja shisetsu no sho energy

    Energy Technology Data Exchange (ETDEWEB)

    Sakura, I.; Kayo, M. [Kajima Corp., Tokyo (Japan)

    1996-06-05

    There are various kinds of sports and leisure facilities. Due to their classes, aims, operation styles and so forth, the grades of aimed environments and facilities change. For example, like a baseball, swimming and skating, quantity of motion and grade of sportswear are different due to their classes and a target environment is also differs. On the other hand, public facility for citizen use is required its cheaper fee, but private facility on commercial base is required its user-collecting capability with added-value. In order to content individual needs of each facility, it is important to combine properly its target environment and its equipment system. The sports and leisure facilities have often large space on their characteristics, and are necessary to maintain their target environments as well as to treat their thermal emission in closed space and to supply their required air. Therefore, it is an extremely meaningful to conduct the energy saving in the facility apt to consume a lot of energy, which is described in this paper mainly on in-door large space facilities. 17 refs., 1 tab.

  6. Numerical study of the mechanism of wavy interface generation in explosive welding; Bakuhatsu yosetsu ni okeru hajo kaimen keisei kiko ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Abe, A. [Kobe University of Mercantile Marine, Kobe (Japan)

    1996-07-21

    Wavy interface generation is an interesting characteristic of explosive welding. There have been many theoretical and experimental discussions of the mechanism of wavy interface generation but there is no consensus of opinion as yet. We report a numerical approach to the analysis of the mechanism of interface wave generation in explosive welding. The phenomena of the interface wave generation are calculated using a two-dimensional finite difference scheme for elastic-plastic materials. In this simulation the equations for a symmetric collision between copper plates are solved. The concept behind this study is that the wavy interface and vortex streets are caused by the velocity distribution of shear flow and periodic disturbances at the interface. The calculation results show the deformation process of the wavy interface and we obtain qualitative agreements between numerical and experimental results. 13 refs., 10 figs., 1 tab.

  7. Heat transfer in an acoustic-resonance tube model and its visualization; Onkyo kyomeikan ni okeru netsuyuso gensho to sono kashika

    Energy Technology Data Exchange (ETDEWEB)

    Ozawa, M.; Kataoka, M. [Kansei Gakuin University, Osaka (Japan). Faculty of Engineering; Kawamoto, A. [Toshiba Corp., Tokyo (Japan); Takifuji, T. [Hitachi, Ltd., Tokyo (Japan)

    1994-12-25

    Acoustic-resonance freezing was devised recently by Wheatley et al that could be called wave freezing that may be applied to chillers used in from small home air conditioners and refrigerators to those for industrial use. With an objective of using these chillers in practical applications, the present study has experimented and discussed the temperature distribution in tubes, transient dynamic movements, and correlation with acoustic fields by using a fundamental resonance model from among the basic design data. The experimental device consists of a speaker for the acoustic vibrator, resonance tubes, and stacking members. Heat transfer in the acoustic resonance tube was experimented, and the temperature distribution in the stacking plates was observed visually by using a temperature sensing liquid quartz sheet. Heat transfer from joints to flank in the pressure amplitude was recognized, and a special temperature distribution was found to be formed by the resonance system. Qualitative elucidation is also possible on the frequency involved in the heat transportation by means of a short stack model and the correlation with kinds of the fluids. Modeling the system as a whole requires further studies. The tested gases include nitrogen, air, R-22 fluorocarbon gas, and helium. 15 refs., 10 figs.

  8. Tape transport control and estimation of reel inertia for magnetic tape drives; Jiki tape kudokei ni okeru reel kansei moment suitei to tape soko seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Yanagihara, N.; Terayama, T.; Sakai, K.; Owada, N. [Hitachi, Ltd., Tokyo (Japan)

    1998-04-01

    The moment of inertia of the tape reel of VTR varies depending on the reel size and the volume of the tape winding around the reel. Due to the variation, the tension control of the tape in the reel-to-reel drive is difficult. To overcome this problem, the paper presents a new method to identify the tape reel without using additional sensors. Based on this identification scheme, the tape transport control is also presented to achieve the precise tension/speed control. This real-time identification approaches are presented for spinning and running. When the tape reels start spinning up, the tape speed is changed stepwise, by which the inertia of the reel can be estimated using the variation of the tape tension at each reel. The process is repeated to improve the accuracy of identification. Under running condition, the changing inertia can be calculated from the tape radii of two reels. The changing tape radius can be detectable with the speed of capstan. The validity of the proposed method has been approved by experiments using VTR. 6 refs., 14 figs., 4 tabs.

  9. Report on survey of promotion of activities implemented jointly in China in FY 1997; 1997 nendo chosa hokokusho (Chugoku ni okeru kyodo jisshi katsudo no suishin chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Rapid economy growth has been observed in Asia including Japan. On the other hand, problems of population and environment grew even worse with the economic growth. Especially, China is the second CO2 emission country in the world. Large energy demand is still forecasted with its economic growth in the future. It is well-known that the energy consumption per unit GDP is very large. Therefore, it is very significant to promote the activities implemented jointly with China for mitigating the emission of greenhouse gases including CO2, which provides a significant meaning for solving global environmental issues as well as for improving regional environmental issues. It is necessary for the above to recognize the appropriate current situations and to promote the activities implemented jointly suitable for the country. Based on the discussions and information exchanges about environmental issues with staffs concerning environmental policies and scientists as well as the field surveys, methods for the activities implemented jointly were investigated to provide some proposals. 4 figs., 8 tabs.

  10. Sessile animals` distribution and their water quality purification function in Tokyo inner bay; Tokyoto naiwan ni okeru fuchaku dobutsu no bunpu to suishitsu joka kino

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, K.; Tsuchiya, T. [Tokyo Metropolitan Research Inst. for Environmental Protection, Tokyo (Japan); Inamori, Y. [National Inst. for Environmental Studies, Tsukuba (Japan); Okutomi, S. [Saitama University, Saitama (Japan). Faculty of Engineering; Nishimura, O.; Sudo, R. [Tohoku University, Sendai (Japan)

    1998-01-10

    With sea banks in the Tokyo Inner Bay as the object, discussions were given on identification of actual living conditions for sessile animals and purification function of their dominant species. In the investigation, submerged visual observations and identification on existing quantities were performed in July, September and November, 1995 and February 1996. The following matters were made clear as a result of the investigation: the number of species ranges from 43 to 46 and is stabilized throughout a year; a phenomenon is repeated that the number of individuals decreases in summer and winter, and increases in spring and fall as breeding seasons as a result of the addition of larva; the existing quantity is accounted for 90% or more by four dominant species of M. e. galloprovincialis, L. f. kikuchii, C. gigas and Balanus spp in that order; sessile animals weighing 9,110 tons are living annually in average in the sea banks extending over a distance of 192 km; amount of COD purification based on the annual average deposition quantity is calculated 19 tons as a daily average, which corresponds to 23% of the total COD quantity flowing in from the Tokyo urban area; and on the other hand, COD, N and P produced by sessile animals become new loads to environment over the life of these sessile animals. 26 refs., 6 figs., 2 tabs.

  11. Efficient calculation of potential distribution in two-layer earth; Niso kozo daichikei ni okeru denki tansa no tame no koritsuteki den`i keisan shuho

    Energy Technology Data Exchange (ETDEWEB)

    Kataoka, M.; Okamoto, Y. [Chiba Institute of Technology, Chiba (Japan); Endo, M.; Noguchi, K. [Waseda University, Tokyo (Japan); Teramachi, Y.; Akabane, H. [University of Industrial Technology, Kanagawa (Japan); Agu, M. [Ibaraki University, Ibaraki (Japan)

    1997-05-27

    An efficient calculation method of potential distribution in the presence of an embedded body in multi-layer earth has been proposed by expanding the method of image with a consideration of multiple reflection between the ground surface and each underground boundary. For this method, when solving boundary integral equation with the potential of embedded body surface as only one unknown, i.e., when obtaining discretization equation, ordinary boundary element program developed for analyzing the finite closed region can be used. As an example, numerical calculation was conducted for the two-layer earth. The analysis expression of potential distribution in the case of the certain embedded body in two-layer earth has never published. Accordingly, the calculated results were compared with those by the integral equation method. As a result, it was concluded that the primary potential obtained from the present method agreed well with that obtained from the integral equation method. However, there was a disregarded difference in the secondary potential. For confirming the effectiveness, it was necessary to compare with another numerical calculation method, such as finite element method. 5 refs., 5 figs.

  12. Interfacial area between gases and liquid in a valve plate column and a bubble cap tray; Barubu danto oyobi hosho danto ni okeru kieki sesshoku menseki

    Energy Technology Data Exchange (ETDEWEB)

    Nakoua, M.; Dribika, M.; Besher, E

    1999-03-05

    A mathematical model has been developed for absorption accompanied by chemical reaction of H{sub 2}S and CO{sub 2} in alkanolamine solutions encountered in plants for natural gas sweetening in Libya. The model has been used to calculate actual number of plates in industrial columns. The model results errors in number of trays predictions due to the lack of procedures for estimating interfacial area for the in between flow regime that prevailed in two industrial plants. The developed correlation for interfacial area estimation for the in between flow regime gives zero error in number of trays prediction. (author)

  13. Experimental studies on performance of tandem hydrofoils in high speed regions; Kosokuiki ni okeru tandem suichuyoku no seino ni kansuru jikkenteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nakatake, K.; Oda, K.; Kataoka, K. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Okada, S. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan); Mizuno, S. [Hitachi Zosen Corp., Osaka (Japan)

    1996-10-01

    With an objective to clarify basic performance of hydrofoils, a towing experiment was carried out on single hydrofoil and tandem hydrofoils, whose results are reported in this paper. In the experiment, the tandem hydrofoils are supported on two stays on the left and right sides, and the whole lifting power and the whole drag including those of the stays were measured by using strain gauges placed on four plate springs. Results of the experiment may be summarized as follows: in the case of the single hydrofoil, the lifting power constant varied as a result of strong impact on free surface as the shallower the hydrofoil, but corresponds to the size of the lifting power coefficient in high speed regions; in the case of the tandem hydrofoils, the smaller the submersion depth, the effects grew larger on the lifting power coefficient and the drag coefficient, similarly to the case of the single hydrofoil; and the lifting power coefficient for the leading hydrofoils changes very little as a result of change in horizontal distance between the tandem hydrofoils, but the lifting power coefficient of the rear hydrofoils vibrates due to influence from the leading hydrofoils, with the peak of the value thereof transferring to the higher speed side as the horizontal distance increases. 3 refs., 10 figs., 2 tabs.

  14. Research report for fiscal 1998. Promotion of activities implemented jointly etc. in China; 1998 nendo Chugoku ni okeru kyodo jisshi katsudo nado suishin chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The Kyoto Protocol allows some flexibility in the implementation of methods for achieving the goal, such as emission trading, activities implemented jointly (AIJ) among advanced countries, construction of clean development mechanisms (CDM) with developing countries, etc., and Japan intends to positively make use of them for the achievement of the goal. For China, who holds second place in the list of greenhouse gas emitting countries in the world, the promotion of CDM is quite important. With the situation taken into consideration, interaction was effected with Chinese officers and scientists of government agencies and academic institutes involved in environmental matters, and researches were conducted. Views and information were exchanged regarding environmental problems and, after on-site investigations, researches were conducted and suggestions were presented as to how AIJ and CDM should be. The suggestions covered Chinese policies toward AIJ and CDM, current state of AIJ projects in China and systems for their promotion, means for enhancing such projects, and discovery of candidates for AIJ and CDM project application. (NEDO)

  15. Effect of total pressure on sulfur capture of Ca-ion exchanged coal; Kaatsu jokenka ni okeru Ca-tanjitan no datsuryu koka

    Energy Technology Data Exchange (ETDEWEB)

    Lin, S.; Benjamin, G.; Abe, H.; Harano, A.; Takarada, T. [Gunma University, Gunma (Japan). Faculty of Engineering

    1996-10-28

    In relation to coal gasification and combustion under high pressure as highly efficient coal utilization, the effect of total pressure and sintering on the SO2 capture ability of Ca-ion exchanged coal and other desulfurizing agents were studied. In experiment, specimens were filled into a small pressurized reactor to heat them under high-pressure N2 atmosphere. After the completion of combustion reaction of char at 850{degree}C, SO2, CO2 and CO gases were measured at an outlet while flowing SO2/N2. As the experimental result, all of the S content in Ca-ion exchanged coal was not absorbed by Ca content in coal during pyrolysis and combustion, resulting in discharge of 36% of the S content. Since Ca-ion exchanged coal is fast in combustion reaction, most of the S content was desulfurized by coal ash. The ash content yielded from Ca-ion exchanged coal was more excellent in SO2 capture ability than limestone even under higher pressure. In the case of CO2 partial pressure lower than equilibrium CO2 pressure for CaCO3 decomposition, the capture ability decreased with an increase in total pressure, while in higher CO2 partial pressure, it was improved. 1 ref., 7 figs., 2 tabs.

  16. Formation of N2 in the fixed-bed pyrolysis of low rank coals and the mechanisms; Koteisho netsubunkai ni okeru teitankatan kara no N2 no sisei

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Z.; Otsuka, Y. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

    1996-10-28

    In order to establish coal NOx preventive measures, discussions were given on formation of N2 in the fixed-bed pyrolysis of low rank coals and the mechanisms thereof. Chinese ZN coal and German RB coal were used for the discussions. Both coals do not produce N2 at 600{degree}C, and the main product is volatile nitrogen. Conversion into N2 does not depend on heating rates, but increases linearly with increasing temperature, and reaches 65% to 70% at 1200{degree}C. In contrast, char nitrogen decreases linearly with the temperature. More specifically, these phenomena suggest that the char nitrogen or its precursor is the major supply source of N2. When mineral substances are removed by using hydrochloric acid, their catalytic action is lost, and conversion into N2 decreases remarkably. Iron existing in ion-exchanged condition in low-rank coal is reduced and finely diffused into metallic iron particles. The particles react with heterocyclic nitrogen compounds and turn into iron nitride. A solid phase reaction mechanism may be conceived, in which N2 is produced due to decomposition of the iron nitride. 5 refs., 4 figs., 1 tab.

  17. Effects of solvent and catalysts on the hydrogenolysis of alkylnaphthalenes; Alkylnaphthalene no suisoka bunkai ni okeru yobai to shokubai no koka

    Energy Technology Data Exchange (ETDEWEB)

    Futamura, S. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    Catalytic effects of metal and carbon materials, which promote hydrogen transfer from hydrogen donor solvents, are investigated during hydrogenolysis of benzyl-1-methylnaphthalenes (BMN) selected as a hydrogen acceptor. For the isomer distribution of BMN after the reaction, almost the same molecular ratio before the reaction was obtained independent of the presence of catalysts. Selectivity of position during the addition of hydrogen atoms from tetralin was not found. For the reaction of BMN in tetralin, 1-methylnaphthalene and toluene were obtained as products, but the formation of benzylnaphthalene was not found. As for the nuclear hydride of BMN, the trace amount formation was confirmed by gas chromatography. For the hydrogen transfer from tetralin progressed catalytically, it was found that the nuclear of naphthalene can not be hydrogenated easily. This was considered to be due to the obstruction of hydrogen transfer from tetralin by the strong adsorption of BMN on the Ni surface. 1 ref., 1 fig., 2 tabs.

  18. Investigation of the deposit formation in pipelines connecting liquefaction reactors; 1t/d PSU ni okeru ekika hanno tokan fuchakubutsu no seisei yoin ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Okada, Y.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan)

    1996-10-28

    The liquefaction reaction system of an NEDOL process coal liquefaction 1t/d PSU was opened and checked to investigate the cause of the rise of differential pressure between liquefaction reactors of the PSU. The liquefaction test at a coal concentration of 50 wt% using Tanito Harum coal was conducted, and it was found that the differential pressure between reactors was on the increase. By the two-phase flow pressure loss method, deposition thickness of deposit in pipelines was estimated at 4.4mm at the time of end operation, which agreed with a measuring value obtained from a {gamma} ray. The rise of differential pressure was caused by deposit formation in pipelines connecting reactors. The main component of the deposit is calcite (CaCO3 60-70%) and is the same as the usual one. It is also the same type as the deposit on the reactor wall. Ca in coal ash is concerned with this. To withdraw solid matters deposited in the reactor, there are installed pipelines for the withdrawal at the reactor bottom. The solid matters are regularly purged by reverse gas for prevention of clogging. As the frequency of purge increases, the deposit at the reactor bottom decreases, but the deposit attaches strongly to pipelines connecting reactors. It is presumed that this deposit is what Ca to be discharged out of the system as a form of deposition solid matter naturally in the Ca balance precipitated as calcite in the pipeline connecting the reactor. 3 refs., 5 figs., 4 tabs.

  19. Conversion of char nitrogen to N2 under incomplete combustion conditions; Fukanzen nensho jokenka ni okeru char chuchisso no N2 eno tenka

    Energy Technology Data Exchange (ETDEWEB)

    Zhuang, Q.; Yamauchi, A.; Oshima, Y.; Wu, Z.; Otsuka, Y. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

    1996-10-28

    The effect of combustion conditions on conversion of char nitrogen to N2 was studied in the combustion experiment of char obtained by pyrolysis of coal. Char specimen was prepared by holding ZN coal of Chinese lignite in Ar atmosphere at 1123K for one hour. A batch scale quartz-made fluidized bed reactor was used for combustion experiment. After the specimen was fluidized in reaction gas, it was rapidly heated to start combustion reaction. CO, CO2 and N2 in produced gases were online measured by gas chromatography (GC). As the experimental result, under the incomplete combustion condition where a large amount of CO was produced by consuming almost all of O2, no NOx and N2O produced from char were found, and almost all of N-containing gas was N2. At the final stage of combustion, pyridinic-N disappeared completely, and pyrrolic-N decreased, while O-containing nitrogen complexes became a main component. It was thus suggested that O-containing nitrogen complexes are playing the role of intermediate product in combustion reaction. 7 refs., 4 figs., 1 tab.

  20. Characterization of the various catalyst for solvent hydrogenation at 1t/d PSU; 1t/d PSU ni okeru kakushu yozai suisoka shokubai no seino hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kakebayashi, H.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Aihara, Y.; Imada, K. [Nippon Steel Corp., Tokyo (Japan)

    1996-10-28

    Performance of various catalysts for hydrogenation of recycle solvent was evaluated for the operation of NEDOL process 1 t/d process supporting unit (PSU). Distillate between 220 and 538{degree}C derived from the liquefaction of Tanito Harum coal was used as recycle solvent. Deactivation behaviors of catalysts were compared using a prediction equation of catalyst life, by which aromatic carbon index (fa) after hydrogenation can be determined from the fa of recycle oil before hydrogenation, reaction temperature, and total hydrogenation time. Total hydrogenation time satisfying the {Delta}fa, 0.05 before and after hydrogenation were 8,000, 4,000, and 2,000 hours for NiMo-based catalysts C, A, and B, respectively. Catalyst C showed the longest life. Used catalysts were also characterized. The catalyst C showed larger mean pore size than those of the others, which resulted in the longer life due to the delay of pore blockage. From measurements by XPS and EPMA, relative atomic concentration of carbon increased remarkably after the use for all of catalysts, which was considered to be due to the adhesion of hydrocarbons. Increase of metal atoms, such as Fe and Cr, was also observed due to the contamination of entrainment residues. Deactivation of catalysts was caused by the adhesion of hydrocarbons, and metallic compounds, such as Fe and Cr. 3 refs., 1 fig., 5 tabs.

  1. Coal liquefaction in early stage of NEDOL process 1t/d PSU; 1t/d PSU ni okeru ekika shoki hanno ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, K.; Kawabata, M.; Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

    1996-10-28

    To investigate the behavior of coal liquefaction reaction in early stage as a part of studies on the coal liquefaction characteristics using NEDOL process 1 t/d process supporting unit (PSU), coal slurry sample was taken from the outlet of slurry preheater located in the upflow of liquefaction reactors, and was tested. Tanito Harum coal was used for liquefaction. Preheater was operated under the condition of pressure of 170 kg/cm{sup 2}, gas flow rate of 64 Nm{sup 3}/hr, and at temperature up to 410{degree}C at the outlet, in response to the standard test condition. The slurry sample was discharged into a high temperature separator with temperature of 250{degree}C. Liquefaction was not proceeded at the outlet of preheater. Solid residue yielded around 80%, and liquid yielded around 15%. Gases, CO and CO2, and water yielded also small amount around 3%. The solid sample contained much IOM fraction (tetrahydrofuran-insoluble and ash), and the liquid contained much heavy oil fraction. Hydrogenation was not proceeded, and the hydrogen consumption was very low showing below one-tenth of that at the usual operation. Hydrogen sulfide gas was formed at early stage, which suggested that the change of iron sulfide catalyst occur at early stage of liquefaction. 1 ref., 5 figs., 2 tabs.

  2. Operation history of hydraulic jet pump on teh Chengbei oil field, China. Chengbei yuden ni okeru haidororikku jet pump no shiyo jisseki

    Energy Technology Data Exchange (ETDEWEB)

    Terao, Yoshihiro; Takagi, Sunao

    1989-11-01

    Changbei oil field in China uses hydraulic jet pump(HJP) to cope with the increase of oil production and increase of water content in the oil field. This paper described the practical result. This pump makes high speed jet by driving fluid, and converts the dynamic energy to pressure energy by decelerating with a diffuser to push up oil. Wellheads damaged by sand friction or near the gas cap were removed. The production from March, 1988 to October increased at the rate of 114kl/day at total 8 wellheads. Heavy oil of API specific gravity of 16 degree could be proved. Since the separation of oil and water was inferior, so that the countermeasures were studied but the cause was not known. Troubles or failures of main body, nozzle and throat of HJP were not occurred. Any effect could not be found at a wellhead of water content exceeding 50 to 60% because only water production increased. Consequently, this process could result the increase of oil production with lower cost and without mechanical failures. 2 refs., 7 figs., 7 tabs.

  3. Application of polymeric solid materials for electrical insulation system in superconducting apparatuses; Chodendo kiki no denki zetsuen kosei ni okeru kobunshi kotai zetsuen no tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Nagao, M. [Toyohashi Univ. of Tech., Aichi (Japan); Minoda, A. [Matsue National College of Tech., Shimane (Japan); Kosaki, M. [Gifu National College of Tech., Gifu (Japan)

    1999-06-07

    We send the electric insulation to one of the technological problem to be solved in order to realize high reliability of the superconductive electric power equipment. This paper must also sufficiently consider not only dielectric characteristic and insulation characteristic but also material mechanical property in which they are excellent at very low temperature in the selection of insulating material. The representative insulating material of XLPE, LDPE mainly used in the region over room temperature the crack may arise by causing mechanical stress by cooling contracture of giant molecule, and the problem occurs as cryogenic insulating material in mechanical property. We propose the ethylene propylene rubber as cryogenic insulating material, and we carry out research and development of superconducting cable of the solid insulation system. We examined dielectric breakdown property and mechanical property of EPR at very low temperature this time. (NEDO)

  4. Numerical simulation of emissions and depositions of acidic air pollutants in East Asia; Higashi ajia chiiki ni okeru taikiosen busshitsu no haishutsu to yuso simulation

    Energy Technology Data Exchange (ETDEWEB)

    Higashino, H. [Agency of Industrial Science and Technology, Tokyo (Japan)

    1997-12-01

    In order to consider how to cope with problems of great-sphere air pollution in the East Asia such as acid rain, etc., it is required to investigate the real conditions of emitted air pollutants and to develop a transfer model which clarify the relation between emissions and depositions. This paper describes the present state of studies on the amount of estimated air pollutive emissions in the East Asia and estimated depositions by transfer models. Typical studies on estimated grid-by-grid distribution of emissions in the East Asia are explained first and other estimated examples, i.e. data announced by the Chinese Government and etc., air also referred. The models developed for estimating acidic pollutants falling down in the East Asia are insufficient, however, acidic pollutant transfer models applied at present are introduced. The results of the author`s study are described and the subjects for a future study are referred. 27 refs., 5 figs., 4 tabs.

  5. Historical consideration on the overseas development of concrete faced rockfill dams; Kaigai ni okeru concrete hyomen shasuiheki gata rokkufiru-damu hatten no rekishiteki kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamamura, T.

    1995-09-05

    It is preferable that height deference between two reservoirs for pumped storage generation is as large as possible, when allowance enough to meet sustained peak of power need is taken into account. Consequently, dam heights are often designed to exceed 100 m. Concrete faced rockfill dams (CFRDs) have been constructed as such high dams because of reducing construction cost and of absence of previous examples, in the world, for constructing dams higher than 100 m with asphalt faced wall. Features, construction achievement, endurance, construction period and economic efficiency are discussed from a viewpoint of historical development of CFRD. CFRDs have advantages over dams of clay-core rockfill type in regards to being economic, short in construction period, heavily endurable, safe against flooding and so on. The number of CFRDs whose height exceeds 50 m had reached 89 by 1993, since Morena dam was constructed first in California state, USA in 1895. Twenty one of them are higher than 100 m. CFRDs have been enduring without disruption nearly for 100 years, although some dams experienced water leak. 15 refs., 2 figs., 3 tabs.

  6. Detection of bit location by acoustic emission technique in horizontal directional drilling. Kojo sakushin koho ni okeru bit ichi no AE ho ni yoru hyotei

    Energy Technology Data Exchange (ETDEWEB)

    Abe, M.; Niitsuma, H. (Tohoku Univ., Sendai (Japan). Faculty of Engineering); Sugimori, S. (Tohoku Univ., Sendai (Japan). Grauduate School); Nakajima, T. (NKK Corp., Tokyo (Japan))

    1991-09-20

    The accuracy of the bit location in the excavation of pilot holes with horizontal drilling technique must be kept less than several tens of centimeters. Such an accuracy is hard to be achieved by the existing controlling technology. The depth of the bit tip can be measured comparatively accurately using a clinometer and the like. The azimuth meter, gyroscope, underground radar, locator, etc. are used for the detection of azimuth of the bit, but every one of them has its own problem. Therefore, new measuring methods to be used in combination with the conventional methods are required which can cover up the shortcomings of the conventional methods. Acoustic emission (AE) technique is employed for the detection of the bit location, and the accompanying problems as well as detecting performance are investigated. It is used for the measurement in the drilling test performed at the reclaimed land on the premises of Keihin ironworks of NKK Corp. In connection with the detection of the bit location in horizontal pilot drilling, a study is made on the zone detection technique for AE signals generated by the bit when striking ground and those generated during drilling. 7 refs., 17 figs., 1 tab.

  7. Technical development of cost-efficient installation of power distribution cables under pavements. Haiden chichuka ni okeru doboku kensetsu gorika gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kokusho, Koji; Kataoka, Tetsuyuki; Tanaka, Yasuyuki; Yoshida, Yasuo; Ikemi, Motoyoshi; Suzuki, Koichi; Kitano, Koichi; Kobayashi, Seiichi; Kanazu, Tsutomu; Komada, Hiroya.

    1987-12-01

    Various latest technical developments were surveyed for the cost-effective installation of power distribution cables under pavements, and their applicabilities were demonstrated with the evaluation of their cost-reduction effects. Cables in conventional vinyl protection tubes could be buried only 30cm under pavements, and in such case, the cost was reduced to 51% of those of conventional methods. As the results of soil tests, excavated soil over 80% was reusable through coarse screening. Underground radar technique to explore buried pipes from the surface was detectable several pipes buried 1.5-2.0m underground, although some problems in precision were found. The improvement of reinforced concrete man-hole structures to minimize the volume of excavated soil indicated the cost reduction of nearly 20%. The application of these techniques to the installation of cables was expected to ultimately halve the total civil engineering cost. 21 refs., 130 figs., 46 tabs.

  8. Application of geophysical methods to investigation of old castle, especially of the moat; Joshi no chosa ni okeru butsuri tansa no tekiyo (horiato no tansa)

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, A.; Karube, F.; Kobayashi, M.; Toge, M. [OYO Corp., Tokyo (Japan)

    1996-05-01

    An explanation is made about the application of geophysical methods to the investigation of the ruins of old castles especially of their moats. Techniques currently in use for exploration of the ruins of castles are mainly underground radar exploration and electric exploration. The underground radar method sends electromagnetic waves through the ground and receives the reflection for a high-precision exploration of the layers shallow in the ground. Therefore, this method is suitable for probing the ruins of castles relatively shallow in the flat land, hills, and mountains. The electric method (resistivity image method) do the probing by use of the two-electrode arrangement, performs inverse analysis on the basis of the obtained data for the determination of the underground resistivity distribution, and displays the distribution in an image easy to read. This method, when there is a great separation between the two electrodes, explores relatively deep into the ground. Thanks to this feature, this method is effective in probing relatively wide and deep ruins of moats, that is, the ruins of moats of castles built in later years, especially of those then filled with water. 2 refs., 5 figs.

  9. Effects of heat release rate on NOx time history in diesel combustion; Diesel nensho ni okeru netsu hasseiritsu keika ga NOx nodo rireki ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Ishiyama, T.; Miwa, K.; Higashida, M. [Tokushima Univ., Tokushima (Japan). Faculty of Engineering; Watanabe, S. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1996-06-25

    For determining the optimum combination of combustion control techniques to reduce NOx emission from diesel engines, it is important to clarify the effects of each technique not only on the NOx emission but also on its time history during combustion. In this paper, NOx concentration in the combustion chamber of a rapid compression machine has been measured by using a total gas sampling method. In order to elucidate the relation between NOx history and heat release rate, air temperatures nozzle hole size and air motion are varied to control the heat release process. The results show that NOx emission is not solely dependent upon initial combustion. Air utilization in the main diffusive combustion phase has great influence on NOx formation and its decay. NOx formation is accelerated by activation of the initial stage of the main combustion when using a nozzle with small holes. 9 refs., 13 figs.

  10. Anodic Behavior of Semiconducting Diamond Thin-film Electrodes in the Electrolyte for Electrochemical Fluorination; Handotai daiamondo denkyoku no denkai fussokayokuchu ni okeru youkyoku kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Shibata, Hirotake.; Kawasaki, Shinji. [Shinshu University, Nagano (Japan). Faculty of Textile Science and Technology; Momota, Kunitake. [Morita Chemical Industries, Osaka (Japan). Department of Research and Development; Okino, Fujio.; Touhara, Hidekazu. [Shinshu University, Nagano (Japan). Faculty of Technology]|[Core Research for Evolutional Science and Technology, Tokyo (Japan). Jaoan Science and Technology Corporation; Gamonishitani, Mika.; Sakaguchi, Isao.; Ando, Toshihiro. [National Institute for Research in Inorganic Materials, Ibaraki (Japan)]|[Core Research for Evolutional Science and Technology, Tokyo (Japan). Japan Science and Technology Corporation

    1998-12-31

    Electrochemical behavior of semiconducting diamond thin-film electrodes has been studied by measuring cyclic voltammograms for the anodic oxidation of 1,4-difluorobenzene in the electrolyte, neat Et{sub 4}NF{center_dot}4HF. A comparative study using a Pt-electrode establishes that the electrochemical fluorination of 1,4-difluorobenzene using the diamond electrode yields 3, 3, 6, 6-tetrafluoro-1, 4-cyclohexadiene. Furthermore no peaks corresponding to the redox reaction of Pt-electrode, i.e., the formation and reduction of PtO{sub 2}, are observed in the CVs obtained using the diamond electrode, suggesting that the diamond electrode is more stable than the Pt-electrode. The results suggests that electrochemical fluorination and the electrolytic production of elemental fluorine are possible at the dimensionally stable diamond electrode. (author)

  11. Improvement of magnetic properties of Fe-50mass%Ni in MIM process; MIM process ni okeru Fe-50mass%Ni no jiki tokusei kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Miura, H. [Kumamoto University, Kumamoto (Japan). Faculty of Engineering; Fujita, S. [Kumamoto University, Kumamoto (Japan); Fujita, M.; Ninomiya, R. [Mitsuikinzoku Co. Ltd., Tokyo (Japan)

    2000-12-15

    Metal injection molding (MIM) process is hoped to be one of processing for required to more complicated parts of magnetic components. In this study, the effect of different types of powders (prealloyed and mixed elemental powders) on the magnetic properties of permalloy (Fe-50mass%Ni) through the MIM technique was investigated. Approximately 94% of theoretical density was obtained by using the prealloyed powder, and the retained carbon and oxygen contents were controlled to be low. On the other hand, 96% of theoretical density was obtained by using the mixed elemental powder, but the magnetic properties were inferior to that of prealloyed powder's because of high retained oxygen content. By using the carbonyl Fe powder with high carbon, the retained oxygen and carbon content could be controlled to be low, resulting in the improved magnetic properties. (author)

  12. Temperature effect on corrosion fatigue strength of coated ship structural steel; Zosen`yoko tosozai no fushoku hiro kyodo ni okeru ondo no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Takanashi, M.; Fuji, A.; Kojima, M.; Kitagawa, M. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Kobayashi, Y. [Ship Research Inst., Tokyo (Japan); Kumakura, Y.

    1997-08-01

    The corrosion fatigue life was obtained using uncoated and tar epoxy resin specimens to clarify the temperature effect. The life curve for corrosion fatigue of machined and uncoated steel in the air and sea was obtained. The fatigue strength of uncoated steel largely decreases in the sea and breaks even in the nominal stress range of less than 1/2 of the fatigue limit in the air. The effect of temperature on the coated steel is represented by a corrosion coefficient. The steel coated at 25{degree}C is 1/1.03 to 1/1.13 at 40 to 60{degree}C. This showed that the fatigue strength decreases when the temperature exceeds 25{degree}C. However, it has not such tendency and significance that are represented quantitatively. There is a slight difference in the short-life area between the crack generation life and breaking life. However, the long-life area has no significance that influences the whole evaluation. In the long-life corrosion fatigue, the crack occurs from the corrosion pit due to the exposure below the coated film and progresses in the base material before the coated film is destroyed. The effect of the corrosion pit remarkably appears at a low-stress level. 14 refs., 14 figs., 4 tabs.

  13. Stabilizing control of crystal size distribution in continuous crystallization processes; Renzoku shoseki purosesu ni okeru kessho ryukei bunpu no anteika seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Naito, K.; Sotowa, K.; Kano, M.; Hasebe, S.; Hashimoto, I. [Kyoto Univ. (Japan). Faculty of Engineering

    1998-03-01

    The sustained oscillation of the crystal size distribution (CSD) in continuous crystallization process is analyzed by simulation using a detailed model. CSD can not be used as a controlled variable because of its distributed nature. Therefore, the method of selecting representability indices for CSD and the stabilizing control of CSD based on those indices are investigated. A multi-loop scheme is proposed, wherein a system with the third moment of large crystal and the rate of product flow from the continuous crystallizer used as the controlled variable and the operating variable, respectively, is added to the SISO control system which employs microcrystal population density as the controlled variable and the microcrystal flow rate as the operating variable. The controlling performances of the newly proposed multi-loop scheme and the SISO control scheme are compared. It is confirmed that the proposed controlling method is effective when the constrain from the microcrystal flow rate is strict. 6 refs., 14 figs., 2 tabs.

  14. Aiming at information sharing. Standardization trend of data exchange in construction equipment; Joho kyoyuka ni mukete. Kenchiku setsubi ni okeru data kokan no hyojunka doko

    Energy Technology Data Exchange (ETDEWEB)

    Terai, T. [Chiba Inst. of Tech., Narashino (Japan)

    1998-09-05

    In a construction project, various information concerning the whole life cycle of construction production from plan, design to maintenance, preservation, abandonment etc. are involved. In this paper, standardization trend of data exchange in construction equipment and actions aiming at realizing information sharing conducted by each relating groups, are explained. At first, in connection to the needs and seeds of the information sharing, progress of information technology such as computer network and personal computer, and globalism of the information system including transformation of CALDS environment are pointed out. Then, in connection to the conditions and questions for the information sharing, the most suitability of communication, integration of the construction production and standardization of common rules are described. As for the actions conducted by each groups, the actions conducted by ISO, IAI, the Construction and Housing International Organization, the Japan Construction Society and CI-NET conducted by the Construction Promotion Foundation are described. 1 fig.

  15. Education for hydraulics and pnuematics in Department of Computer Science, Faculty of Information Sciences, Hiroshima City University; Hiroshima shiritsudaigaku ni okeru yukuatsu kyoiku

    Energy Technology Data Exchange (ETDEWEB)

    Sano, M. [Hiroshima City University, Hiroshima (Japan)

    2000-03-15

    Described herein is education of hydraulics and pneumatics in Hiroshima City University. Department of Computer Science is responsible for the education, covering a wide educational range from basics of information processing methodology to application of mathematical procedures. This university provides no subject directly related to hydraulics and pneumatics, which, however, can be studied by the courses of control engineering or modern control theories. These themes are taken up for graduation theses for bachelors and masters; 2 for dynamic characteristics of pneumatic cylinders, and one for pneumatic circuit simulation. Images of the terms hydraulics and pneumatics are outdated for students of information-related departments. Hydraulics and pneumatics are being forced to rapidly change, like other branches of science, and it may be time to make a drastic change from hardware to software, because their developments have been excessively oriented to hardware. It is needless to say that they are based on hardware, but it may be worthy of drastically changing these branches of science by establishing virtual fluid power systems. It is also proposed to introduce the modern multi-media techniques into the education of hydraulics and pneumatics. (NEDO)

  16. High-resolution aeromagnetic survey in the area of Arima-Takatsuki-Rokko active fault system; Arima Takatsuki Rokko katsudanso chiiki ni okeru komitsudo kuchu jiki tansa

    Energy Technology Data Exchange (ETDEWEB)

    Nakatsuka, T.; Okuma, S.; Morijiri, R.; Makino, M. [Geological Survey of Japan, Tsukuba (Japan)

    1996-10-01

    High-resolution aeromagnetic survey was conducted in December, 1995, over the area of Arima-Takatsuki-Rokko active fault system, where the 1995 Hyogo-South (Kobe) earthquake took place. Based on the surveyed data, the magnetic anomaly distribution in the Kei-Hanshin district was illustrated. Features of magnetic anomaly observed in it were discussed. Influence of artificial structures in the coastal zone of Kobe City was tried to be removed. Distinct magnetic anomaly observed in the center of Kyoto City was located at the southern part near Shijo-Karasuma. This was mainly affected by the artificial structure. A high magnetic anomaly with a long wave length was observed in the southern part of Kyoto. There was a high magnetic anomaly in an area surrounded by central cities of Nishinomiya-Toyonaka district. At the location where positive and negative magnetic anomalies were illustrated in NEDO`s map in the coastal zone of Kobe City, the anomaly pattern was clarified. The influence of artificial structure was approximated using a point dipole. The dipole was placed in each block having a magnetic anomaly. The parameter was determined by the inverse analysis, to remove the influence. Consequently, most of magnetic anomalies due to artificial structures could be removed. 6 figs.

  17. Change in surface SP caused by pressure buildup observed at the Nigorikawa geothermal area; Nigorikawa chiiki ni okeru atsuryoku buildup ji no shizen den`i henka

    Energy Technology Data Exchange (ETDEWEB)

    Yasukawa, K.; Yano, Y.; Matsushima, N.; Ishido, T. [Geological Survey of Japan, Tsukuba (Japan); Takahashi, M.; Suzuki, I.; Aoyama, K.; Kuwano, T.

    1996-10-01

    To examine the effect of change of subsurface flow system on the surface SP (self potential), SP measurements were carried out before and after the pressure buildup and drawdown during the periodic inspection at Nigorikawa area. Relation between the SP distribution and the observed data was also examined by 2-D numerical simulation. Tendency was found that the SP increased gradually with the production near the production well, decreased during the pressure buildup, and increased again during the drawdown. There were some points having the reverse tendency in the surrounding area. Behavior during the pressure buildup and drawdown was not clear. The resistivity near the ground surface was low ranging between 2 and 5 ohm/m within the Nigorikawa basin. The variation of SP was not so large when compared with the measuring error. The SP profiles on the secondary section passing in the center of caldera at the production stop and at one week after the production start were well corresponded with the profiles under natural conditions which were reproduces using the 2-D model. It was considered that the SP profile before the production stop was affected by the production. 12 refs., 6 figs., 1 tab.

  18. Comparison of {gamma}-ray profile across active normal and reverse faults; Seidansogata to gyakudansogata katsudanso ni okeru hoshano tansa kekka no hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Iwata, A.; Wada, N.; Sumi, H. [Shimada Technical Consultants, Ltd., Shimane (Japan); Yamauchi, S.; Iga, T. [Shimane Univ., Shimane (Japan)

    1996-10-01

    Active faults confirmed at trench and outcrop were surveyed by the {gamma}-ray spectrometry. The active fault found at trench is a normal fault, and that found at outcrop is a reverse fault. The {gamma}-ray spectral characteristics of these two types of faults were compared to each other. The normal fault is named as Asagane fault located in Aimi-machi, Saihaku-gun, Tottori prefecture. The reverse fault is named as Yokota reverse fault located in Yokota-cho, Nita-gun, Shimane prefecture. Rises of radon gas indicating the existence of opening cracks were confirmed above the fault for the normal fault, and at the side of thrust block for the reverse fault. It was considered that such characteristics were caused by the difference of fault formation in the tensile stress field and in the compressive stress field. It was also reconfirmed that much more information as to faults can be obtained by the combined exploration method using the total counting method and the spectral method. 14 refs., 7 figs.

  19. Pseudo-random data acquisition geometry in 3D seismic survey; Sanjigen jishin tansa ni okeru giji random data shutoku reiauto ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Minegishi, M.; Tsuburaya, Y. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1996-10-01

    Influence of pseudo-random geometry on the imaging for 3D seismic exploration data acquisition has been investigate using a simple model by comparing with the regular geometry. When constituting wave front by the interference of elemental waves, pseudo-random geometry data did not always provide good results. In the case of a point diffractor, the imaging operation, where the constituted wave front was returned to the point diffractor by the interference of elemental waves for the spatial alias records, did not always give clear images. In the case of multi point diffractor, good images were obtained with less noise generation in spite of alias records. There are a lot of diffractors in the actual geological structures, which corresponds to the case of multi point diffractors. Finally, better images could be obtained by inputting records acquired using the pseudo-random geometry rather than by inputting spatial alias records acquired using the regular geometry. 7 refs., 6 figs.

  20. Bacterial cultivation in high magnetic fields by 7-tesla superconducting magnet; 7T chodendo magnet ni yori hasseishita kojiba ni okeru biseibutsu no baiyo

    Energy Technology Data Exchange (ETDEWEB)

    Okuda, M.; Saito, I.; Kamikado, T.; Ito, S. [Kobe Steel, Ltd., Kobe (Japan); Matsumoto, K. [Japan Magnet Technology Inc., Kobe (Japan); Liuno, K.; Tsuchiya, K.; Ano, T.; Shoda, M. [Tokyo Institute of Technology, Tokyo (Japan). Research Laboratory of Resources Utilization

    1994-12-20

    Although a large number of studies on effects of magnetic fields on living organisms was reported, no definite results were obtained in many cases because the related conditions are non-uniform and uncertain, such that the uniform magnetic space is smaller than test samples, and temperature control is insufficient. Therefore, the present study developed a microorganism cultivation system that is applied with a 7-T superconducting magnet. This system has the following features: it generates homogeneous magnetic fields of 0.5 to 7 T {plus_minus} 0.5% in the space with a diameter of 100 mm and a length of 200 mm in a normal temperature bore (with a diameter of 160 mm); it can cultivate microorganisms aerobically at temperatures of 10 to 70{degree}C {plus_minus} 0.1{degree}C; it can perform the cultivation simultaneously with a control cultivation in a small magnetic field weaker than the geomagnetism; and a gradient magnetic field and a variable magnetic field can also be applied. As a result of cultivating colibacillus by using the system, a proliferation effect greater by 40% to 80% than the control was obtained in a uniform magnetic field of 7 T, and a proliferation effect greater by several times in variable magnetic fields of 5.2 to 6.1 T was attained with good reproducibility. 22 refs., 8 figs., 1 tab.

  1. Numerical simulation of nematic liquid crystalline flow in two-dimensional L-shaped channels; Nijigen L gata ryuro ni okeru nematic ekisho no nagare no suchi simulation

    Energy Technology Data Exchange (ETDEWEB)

    Chono, S.; Tsuji, T. [Fukui University, Fukui (Japan). Faculty of Engineering

    1995-05-25

    Finite difference solutions to the Leslie-Ericksen equations were obtained for flows in two-dimensional L-shaped channels with various contraction ratios of the upstream to downstream channel width. A streamline shift toward the outer wall occurs upstream of the reentrant corner. Such behavior is similar to that of viscoelastic fluids. With increasing contraction ratio, the streamline shift occurs further upstream. The effect of the wall anchoring angle for the director is remarkable; for example, when the anchoring angle along the downstream walls is set to be opposite to the main flow direction, a distortion of streamlines is produced in the corner region and the director moves to the downstream region upside down. At small Ericksen numbers, the orientation angle for the director is varied over a wide area so as to suppress its local deformation. In contrast, when the Ericksen number is large, the director profile in the upstream region is retained close to the corner region where the director turns rapidly to the downstream direction. 7 refs., 9 figs., 1 tab.

  2. Numerical analysis of polymeric liquid crystalline flows between parallel plates. Heiko heibankan ni okeru kobunshi ekisho no nagare no suchi kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Chono, S.; Iemoto, Y. (Fukui Univ. (Japan). Faculty of Engineering); Taniguchi, A.; Tsuji, T. (Fukui Univ., Fukui (Japan). Graduate School)

    1992-11-25

    Liquid crystal is an anisotropic fluid having both fluidity possessed by liquid and optical anisotropy inherent in crystals. Heretofore, Doi theory, which was established in 1981, is the only theory that can describe the rheology behavior of polymeric liquid crystal. Conventionally, there have been studies carried out based on the Doi theory for clarifying the rheology characteristics of polymeric liquid crystal, but there have been very few in which the Doi theory is applied to the flow in a tube. In this paper, the simple shearing flows of polymeric liquid crystal are first described by employing the Doi theory, and then the results of analysis of flows between parallel plates are stated. The main results obtained are as follows. The orientation of polymeric liquid crystal is determined by relative magnitudes of the terms of average field potential and of velocity gradient. In the flows between parallel plates, the propotion of increase of flow rate increases with the pressure gradient, and polymeric liquid crystal possesses a shear-thinning viscosity like normal polymeric fluid. 14 refs., 7 figs.

  3. Tumbling behavior of a nematic liquid crystal in inlet flow between parallel plates; Heiko heibankan iriguchi nagare ni okeru nematic ekisho no tumbling kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Tsuji, T.; Chono, S. [Fukui University, Fukui (Japan). Faculty of Engineering

    1995-07-25

    Two-dimensional tumbling behavior is investigated numerically by calculating inlet flows of a tumbling-type nematic liquid crystal between parallel plates. Calculations are performed for various Ericksen numbers. At the comparatively small Ericksen number of Er=10, the director in the upper half space of the channel rotates counter-clockwise before reaching the fully developed value. At Er=50, the director shows an abrupt rotation just after the inlet section. The rotation is not only convected to the downstream area but propagated from the region near the channel wall where shear rate is large to the center region. When Er is increased further to 100, the director profile does not indicate a monotonic development but a two-step one. In this case, the velocity profile in the main flow direction is wavelike. It is found that the effect of director orientation is strongly reflected on the velocity field, while the reverse effect is weak. 26 refs., 8 figs., 1 tab.

  4. Conditions of existence of fuzzy explanations and approximate solutions in fuzzy abduction; Fuzzy abduction ni okeru setsumei no sonzai joken to kinji kaiho

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, K. [Nagaoka Technical Coll., Niigata (Japan)] Mukaidono, M. [Meiji Univ., Tokyo (Japan)

    1998-09-30

    Abduction is a procedure to derive a set of hypotheses which explains a set of observed events under given knowledge. The obtained set of hypotheses is called explanation. Previously, the authors proposed fuzzy abduction that was an extension of the abduction with the fuzzy theory and showed the way to derive fuzzy explanation. In this theory, observed events and hypotheses are expressed and the given knowledge is expressed by a set of implications with a truth value between zero and one. However, there is no guarantee that fuzzy explanations always exist. This paper clarifies the necessary and sufficient conditions of the existence of fuzzy explanations and proposes a method to obtain approximate solutions when fuzzy explanations do not exist. Fuzzy abduction is a procedure similar to the inverse operation of fuzzy relational equations, however, the proposed method does not require iterative calculation whose number of times cannot be obtain beforehand. 10 refs., 1 fig.

  5. Numerical analysis of combustion mechanism in iron bath type smelting reduction furnace. Tetsuyokugata yoyu kangenro ni okeru nensho kiko no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Shinotake, A.; Takamoto, Y. (Nippon Steel Corp., Tokyo (Japan))

    1992-07-01

    Introduction and numerical analysis based on mathematical model has been made on the combustion phenomena, and the obtained results are used to analyze material and heat balance in the smelting reduction furnace. Distribution of gas flow, temperature and concentration into the furnace has been possible to estimate for the case where coke or coal is taken as raw material. Variation of dual combustion rate while changing supplied amount of coal species in smelting reduction experiment with 5t capacity, is explained. Under constant oxygen injection, one of the material and heat balance point which operates material and temperature at constant state by coal species and heat loss amount, has been determined, and dual combustion rate and heat efficiency at this point are determined simultaneously. Dual combustion rate and heat efficiency, the source unit of coal and oxygen have increased with the increase of amount of heat loss where as the production of molten iron decreased. Material and heat balance point is shifted to the point with less supply of coal and oxygen when prereduction degree of the ore is increased, and dual combustion rate and heat efficiency has increased. 11 refs., 7 figs., 4 tabs.

  6. On the muscle activity control in the hierarchy motor systems. Hierarchy undo system ni okeru kin no kassei seigyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Akiba, M.; Miyamoto, Y. (Osaka Industrial University, Osaka (Japan). Faculty of Engineering)

    1991-10-31

    Excitory impulses for motor systems are controlled by the psychophysiological nervous systems in the body either autonomically or voluntarily. Involved in the voluntary control loop are motor cortex, basal gangalia, thalamus, cerebellum, etc. The purpose of this study is to confirm whether it is possible to reduce or emphasize the muscle contraction voluntarily through electromyogram (EMG) feedback training. EMG can indicate the excitory impulses of motor units. In the experiments, electrodes were placed on the skin above muscles. A significant reduction effect was observed for subjects trained in relaxation of the forehead musculature through EMG feedback. Results of the experiments suggested that biofeedback training for relaxation of the forehead tensional muscle might be effective in eliminating muscle contraction, and that feedback training for activation of damaged muscles might be effective in emphasizing muscle contraction. 4 refs., 9 figs.

  7. Research activities at thermo-fluid engineering laboratories in Takushoku University; Takushoku Daigaku kogakubu kikai system kogakuka ni okeru ryutai kogaku oyobi netsukogaku kankei no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, I.; Hori, M.; Matsunaga, N. [Takushoku University, Tokyo (Japan)

    1999-01-20

    This paper introduces general conditions of studies at the Machine System Engineering Department of the Faculty of Engineering at the Takushoku University. Studies related to transonic cascade flutters in fluid engineering include behavioral analysis of impact waves around vibrating blades. Behavior of impact waves making twisting vibration at high vibration frequency is elucidated by means of schlieren photography. In addition, the single blade vibration method is used to analyze aerodynamic decay properties of cascades. Elucidation is made on non-steady stalling properties of vibrating single blades (particularly, the hysteresis phenomenon of stalling elevation angles with restoring elevation angles). In the field of thermal engineering, studies are being made on effects of unburned components on NO-NO{sub 2} conversion using a fluidity reactor. Similar reactions are being studied by means of chemical dynamics calculations using the CHEMKIN-II/SENKIN program. A coaxial jet flow experimenting equipment is used to study NO{sub 2} generating mechanism in the field closer to real combustors. Data are accumulated to verify numerical computation by experiments and measurements of spraying flames produced by a model spray combustor. Measurements and experiments are also performed on absorption of NO{sub 2} into water, and on coefficient of diffusion between two kinds of gases. (NEDO)

  8. Switching surge overvoltages on a feeding system of a MAGLEV train; Jiki fujoshiki tetsudo no kidenkei ni okeru kaihei surge kaden`atsu

    Energy Technology Data Exchange (ETDEWEB)

    Muragishi, H. [Nippon Yusoki Co. Ltd., Kyoto (Japan); Nakamura, Y.; Muraoka, N.; Ametani, A. [Doshisha Univ., Kyoto (Japan)

    1997-04-20

    Discussions using simulations were given on surge overvoltages and earth fault surge overvoltage associated with operation of a section switchgear in a feeding system of a MAGLEV train. Results of the discussions may be summarized as follows: throw-in surge overvoltage caused by the section switchgear is about 25 kV at maximum on the coil and about 15 kV on the cable sheath. The coil overvoltage increases as the closer to 90 degrees the throw-in phase approaches, and the greater the power supply frequency increases. The cable sheath overvoltage, however, is not affected by these environments. Breaking surge overvoltage caused by the section switchgear reaches 115 kV on the coil and about the same value on the cable sheath when the breaking current is 50 A. Earth fault surge overvoltage due to cable fault is 24 kV at maximum on the coil, while it reaches 32 kV on the cable sheath. The cable sheath overvoltage depends largely on sheath installing conditions. These overvoltages can be suppressed sufficiently lower than insulation levels of each device by installing arresters. 17 refs., 18 figs.

  9. Novel control strategies of HVDC system with self-commutated converter. Jireishiki henkanki wo tekiyoshita HVDC sytem ni okeru tanshi seigyo to kyocho seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Tokiwa, Y.; Ichikawa, F.; Suzuki, K. (Tokyo Electric Power Co. Inc., Tokyo (Japan)); Inokuchi, H.; Hirose, S.; Kimura, K. (Toshiba Corp., Tokyo (Japan))

    1992-01-20

    This report describes new control strategies of a self -commutated converter applied to the HVDC systems; that is, the cooperative control for a two-terminal transmission system and the terminal control which is applicable to a multi-terminal system. The DC voltage control with an upper and lower power-limiter showed excellent characteristics when applied to the two- terminal transmission system. A voltage margin method was also introduced as a power flow reversal method. These terminal control methods, if required, are able to change interchange power at the receiving end in the case of fault in the communication system. Moreover, the DC voltage control with two-stage voltage control characteristics was proposed for the multi-terminal HVDC system. with this mehtod, the DC transmission system can be operated continuously and stably cooperating electric power at each terminal even when one terminal is collapsed. The terminal control performance in the above two-terminal HVDC system was tested with a simulator. The result showed favorable performance characteristics at the time of power flow reversal and one terminal start-up during other terminal operation. 5 refs., 16 figs.

  10. Pitting corrosion of copper in aqueous solutions containing phosphonic acid as an inhibitor. Hosuhon san wo inhibita toshite fukumu suiyoekichu ni okeru do no koshiku ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Y. (Muroran Univ., Hokkaido (Japan). Graduate School); Seri, O.; Tagashira, K. (Muroran Univ., Hokkaido (Japan)); Nagata, K. (Sumitomo Light Metal Co. Ltd., Tokyo (Japan). Technical Research Lab.)

    1993-09-15

    Phosphonic acid-based inhibitors that are poured into cooling water for copper-tube circulation systems for open heat-accumulators were studied on their influence on pitting corrosion of copper. Amino trimethylene phosphonic acid (ATMP) dissolved into distilled water to 50 ppm was used for the immersion corrosion test. The corrosion-proof effect of additives such as ZnSO4, benzotriazole (BTA) was tested too. 0.5 mm thick phosphate-treated copper plates with a hole of 5 mm in diameter were used as test specimens. Pitting corrosion on the copper plate occurred when ATMP, BTA and ZnSO4 coexisted. It was proved that SO4 [sup 2-] is essential since Na2SO4 in stead of ZnSO4 induced also corrosion. The pitting took place when 0.6 ppm or more of SO4 [sup 2-] was present in a BTA-added ATMP solution. It was observed that the pitting is prone to occur with increase of SO4 [sup 2-] and the number of pitting increases. The following relationship is established when pitting corrosion occurs; E[sub b] [le] E[sub corr], where the former is a potential value at which current density shows a steep increase and the latter is an average value of spontaneous electrode potential showing a plateau. 8 refs., 11 figs., 1 tab.

  11. Investigational study on the development, production and wide spread of welfare apparatus in north Europe; Hokuo ni okeru fukushi yogu no kaihatsu seisan fukyu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of grasping the present situation of the development/production/spread of welfare apparatus in north Europe, an investigation was conducted paying visits to Sweden and Denmark. Basically in the Swedish policy for handicapped persons, disablement is defined not only as features which belong to each individual, but as problems arising when the environment surrounding each individual touches one another. Moreover, characteristics of their policies on welfare apparatus are that major welfare apparatus can be provided for the disabled free of charge, and that the government and public organs play a major role in each step of the development, evaluation, distribution and provision of welfare apparatus. Features of the market of welfare apparatus are that users and buyers of the apparatus are different persons, that a public corporation called SUB participates in determining selling prices, etc., and that the market reflects needs and requests from users comparatively naturally. The needs for welfare apparatus at the Research Institute of Handicapped Persons are grasped through opinion exchanges with groups of handicapped persons or information exchanges with the technical aid center. 3 refs., 11 figs., 10 tabs.

  12. Results of geophysical survey on Hanaore-fault in the Kyoto urban area; Butsuri tansa ni yoru Kyoto shigaichi ni okeru Hanaore danso chosa

    Energy Technology Data Exchange (ETDEWEB)

    Yoshioka, T. [Geological Survey of Japan, Tsukuba (Japan); Echigo, T. [Osaka Soil Test, Osaka (Japan); Toshioka, T.; Matsubara, Y. [Oyo Corp., Tokyo (Japan)

    1997-05-27

    This paper reports results of gravity survey and seismic survey using the shallow bed reflection method to identify distribution of the Hanaore fault in the Kyoto urban area. In the gravity survey, level differential structure caused by the fault was identified as an abrupt change in Bouger anomalous values. The continuity therefrom made the estimation possible on existence and positions of such faults as the Hanaore fault belonging to the Hanaore fault system, the Shishigaya fault, the Kaguraoka fault, and the Okazaki fault. The estimation as a result of the gravity survey include the following findings: the Hanaore fault runs from south of the Yoshidayama in the south-north direction; the distribution of the Okazaki fault has a level differential structure falling on the east side; the structure shows low Bouger anomaly distribution; and this area forms a rift valley belt. In the seismic survey using the shallow bed reflection method, no distinct reflection plane considered as the basement was verified because of influence from urban area noise. However, it was possible to estimate such an underground structure as a monoclinal fold from shapes of the reflection plane and the distribution depths. 7 refs., 5 figs.

  13. Discussion on sensor location in circular array for spatial autocorrelation method; Kukan jiko sokanho no enkei array ni okeru jishinkei haichi no kento

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H.; Iwamoto, K.; Saito, T.; Yoshida, A. [Iwate University, Iwate (Japan). Faculty of Engineering

    1997-05-27

    Methods to derive underground structures by utilizing the dispersion phenomenon of surface waves contained in microtremors include the frequency-wave number analysis method (the F-K method) and the spatial autocorrelation method (SAC method). The SAC method is said capable of estimating the structures to deeper depths than with the F-K method if the same seismometer is used. However, the F-K method is used more frequently. This is because the SAC method imposes a strict restriction that seismometers must be arranged evenly on the same circumference, while the F-K method allows seismometers to be arranged arbitrarily during an observation. Therefore, the present study has discussed whether the SAC method can be applied to observations with the seismometers arranged in the same way as in the F-K method, by using microtremor data acquired from actual observations. It was made clear that a seismometer arrangement for the SAC method may be sufficed with at least three meters arranged on the same circumference. These meters may not have to be arranged evenly, but because the acquired phase velocities may vary according to wave arriving directions and seismometer arrangement, it is desirable to perform observations with seismometers arranged as evenly as possible. 13 figs.

  14. Array measurements of long-period microtremors in southwestern Kanto plain, Japan; Kanto heiya nanseibu ni okeru yaya choshuki bido no array kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Yamanaka, H.; Sato, H.; Kurita, K.; Seo, K. [Tokyo Institute of Technology, Tokyo (Japan)

    1997-05-27

    Array measurements of long-period microtremors were carried out in the southwestern part of Kanto Plain, Japan, to obtain S-wave velocity structures in sedimentary beds as fundamental data for estimating long-term strong ground motion in Kanto Plain. The major component in a long-term seismic motion observed in Kanto Plain is the surface wave. According to the result of observations on Love wave by Kinoshita et al, the wavelengths of the surface waves of a long-term cycle are 10 to 20 km. Therefore, if an array observation is to be performed at intervals of about two wavelengths, about 40 points will be required to cover the entire Kanto plain. The final phase velocity is decided by averaging phase velocities of each cycle obtained for each data set. The acquired phase velocities are analyzed inversely by using a genetic algorithm to derive the S-wave velocities at each observation point. The present microtremor array observation has used 13 points in the southwestern part of Kanto Plain to acquire S-wave velocity (Vs) distribution in sedimentary beds. It was made clear that beds with Vs of 1.0 km/s and Vs of 1.5 km/s exist in this area between the surface bed and the seismic foundation with Vs of about 3 km/s. 10 refs., 10 figs., 1 tab.

  15. Airborne gamma-ray survey around the Negoro fault. 1; Negoro danso shuhen chiiki ni okeru kuchu {gamma} sen tansa. 1

    Energy Technology Data Exchange (ETDEWEB)

    Nakayama, E.; Kasuya, Y.; Hasegawa, H. [Aero Asahi Corp., Tokyo (Japan); Tsukuda, E. [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    An airborne gamma-ray survey was carried out to investigate the active fault system in the central structure line in the peripheral area of the city of Wakayama. At the same time, with an objective to enhance applicability of the airborne gamma-ray survey to active fault investigation, fundamental data were acquired and discussed. The measurement data were processed according to the standard method specified by IAEA. An ID-FFT filter and a nonlinear filter were employed to extract anomalous gamma-ray intensity values. The gamma-ray intensity distribution chart shows a noticeable positive anomalous area extending from the central part of the western edge to the north-east direction. This area agrees nearly well with the Negoro fault, but its peak portion is positioned slightly more to south than the position of the Negoro fault shown in existing data. The Sakuraike fault and the vicinity of the central structure line also show positive anomaly as a whole, particularly remarkably in the vicinity of their converging portion. However, differing from the vicinity of the Negoro fault, the areas are not extracted as an anomalous area which has directionality and extends in a line form. One of the factors for this would be that it is a fault in unsolidified deposits with low opening trend, differing from the one in solidified rocks. 1 fig., 3 tabs.

  16. FY 1998 annual report on power generation by waste heat from cement production in China; Chugoku ni okeru cement hainetsu hatsuden 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project is to implement a feasibility study for applying waste heat power generation, which have been already commercialized in Japan and producing remarkable results, to China's cement plants producing 3,500 t/d or more of clinker, and thereby to try to establish a link with the Japan's clean development mechanism. It is expected that introduction of these systems improves energy use efficiency and environments in China. The study results indicate that the project for a Tongling Conch plant could generate power of 15,000 kW, reducing CO2 emissions by 89,178 t/y and cumulatively 1,783,560 tons in the 20-year period. The results also indicate that the project will be highly profitable, with an estimated internal return rate of as high as 33.78%. The project for a Huaxin plant could generate power of 8,400 kW, reducing CO2 emissions by 48,412 t/y and cumulatively 968,240 tons in the 20-year period, annually saving power charges by 325 million yen and bringing an internal return rate of 10.72%. (NEDO)

  17. Development of high field magnets at the National Research Institute for Metals. Kinzoku zairyo gijutsu kenkyusho ni okeru kojikai magnet gun no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kiyoshi, T.; Inoue, K.; Maeda, H. (National Research Inst. for Metals, Tsukuba (Japan))

    1993-06-20

    Sinece 1988, the Scince and Technology Agency has initiated the superconductor multicore project, which has a purpose of the versatile study on the high temperature superconducting materials of the oxide series. The National Research Institute for Metals is in charge of 5 cores out of them, and in the performance evaluation core which is one of them, the development of each kind of the high field magnets is being advanced for evaluating the characteristics under the high magnetic field. As the magnets, including the 40T class hybrid magnet which generates the steady state magnetic field of 40T, the superconducting magnet of 20T with a large diameter which generates the magnetic field over 20T with a superconductor, the condenser bank system for the pulse magnet to generate the pulse magnetic field up to 80T, and the ultra-precise magnet system which generates the magnetic field with a high uniformity will be consolidated. Keeping pace with a removal of the National Research Institute for Metals to Tsukuba, the construction of the strong magnetic field station is being advanced in the Sakura area. These several kinds of magnets are scheduled to be used in turn for the international joint study. 33 refs., 5 figs., 4 tabs.

  18. Temperature control of a heat exchanger for the photosensitive materials coating and drying process; Kanko zairyo tofu kanso purosesu ni okeru kucho system no ondo seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Kido, K.; Sato, N.; Shimoji, M. [Konica Co. Ltd., Tokyo (Japan). Production Engineering Center; Nakanishi, E. [Kansai Univ., Suita, Osaka (Japan). Faculty of Engineering

    1997-11-01

    A feedforward/feedback control system was developed to maintain the temperature profile of air in an air conditioning system for photosensitive material coating and drying. The feedforward control was attained based on a heat exchanger dynamic model using the flow rate of hot water as the manipulated variable and the air temperature as the controlled variable, while feedback control was performed by means of optimum control theory based on a linearized heat exchanger dynamic model. To evaluate the performance of the control system developed in this study, simulation and experimental studies were carried out where a stepwise change of set values is performed in order to maintain uniform production quality for each product grade. It is shown that the control system under consideration successfully controls air temperature in an air conditioning system for photosensitive material coating and drying. 4 refs., 7 figs.

  19. Temperature dynamic models of heat exchanger for photosensitive material coating and drying processes; Kanko zairyo tofu kanso process ni okeru kucho system no ondo doteki model

    Energy Technology Data Exchange (ETDEWEB)

    Kido, K.; Sato, N.; Shimoji, M. [Konica Co. Ltd., Tokyo (Japan); Nakanishi, E. [Kobe University, Kobe (Japan). Faculty of Engineering

    1996-01-20

    Nonlinear and linear temperature dynamic models of a heat exchanger were investigated for air conditioning control of coating and drying processes for photosensitive materials. The nonlinear model was derived from heat balance based on the assumption of lumped parameter system that the heat exchanger is divided into small parts in the direction of flow (divided cell model). In each part, the temperature of the heating fluid, heated fluid and heat transfer tube with fin are assumed to be uniform. Parameters involved in this model were estimated from experimental data of the step response characteristics of temperature. The linear model is obtained by linearizing this nonlinear model. It was confirmed that the dynamic behavior of temperature can be successfully expressed by both nonlinear and linear models. Both models are considered to be utilizable for process analysis and control system design of the air conditioning system under consideration. 1 ref., 13 figs., 2 tabs.

  20. Fatigue properties of austempered ductile cast iron at room and elevated temperatures; Austemper kyujo kokuen chutetsu no chukoon ni okeru hiro tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Fukuyama, K.; Hasegawa, N.; Inaga, K. [Gifu University, Gifu (Japan)

    1995-06-15

    Austempered ductile cast iron (ADI) is used widely as a structural material with high strength and toughness. However, since few studies have been made on investigation of fatigue properties at medium to high temperatures, this paper describes rotating bending tests carried out in temperature range between room temperature and 400{degree}C to investigate the fatigue properties and the fatigue crack generating behavior. The following results were obtained: the fatigue limit (fatigue strength after 10{sup 7} bendings) showed a remarkable maximizing phenomenon at temperatures around 300{degree}C; micronization of the base structure caused by transformation of residual austenite was recognized above 300{degree}C, and so was rise in the hardness; heating to this temperature led to rise in the Ms point, making the transformation occur more easily; the effect of repetitive stress causes a processing induced transformation; the temperature at which the transformation and the micronization are completed declines by about 50{degree}C lower than in the non-transformed region; and the fatigue fracture at middle to high temperatures is caused more frequently by internally existing graphite and development of cracks from very small casting cavities. 31 refs., 10 figs., 7 tabs.

  1. Cooperative measurements of microtremors in the north-eastern region of Nishinomiya city, Hyogo Pref.; Nishinomiyashi hokutobu ni okeru joji bido no godo kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Maiguma, T.; Matsuzawa, H. [Saitama University, Saitama (Japan). Faculty of Engineering; Sawada, Y.; Tazawa, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-05-01

    For the purpose of generally grasping space distribution of ground vibration characteristics, cooperative measurements were conducted in a wide area, mainly in the area stricken by the M7 earthquake. Forty-five organs such as governmental institutes, universities, and private company institutes participated in the measurements which were conducted at 1967 measuring points. The area which the author is in charge is an area from the north of Nishinomiya City to the south of Takarazuka City. The area is relatively far from the hypocenter area, but the magnitude is 7 there and damage was concentrated. The measurements were made by each independent team from August 29 to September 1, 1995. As a result of spectral measurements of NS, EW and UD components, conspicuous peaks were seen in an extent of 1.5 sec. cycle in almost all measuring points and components. Further, in spectra of horizontal motion components of A measuring point group, conspicuous peaks were seen in an extent of 0.15-0.5 sec. cycle, and in those in B and C measuring point groups, in an extent of 0.35-0.5 sec. cycle. In upper/lower motion components, conspicuous peaks were seen in an extent of 0.3 sec. cycle in A measuring point group. 4 figs.

  2. Questionnaire investigation for the earthquake in Honjo city and Yazawa city, Akita Prefecture; Jishin ni kansuru ishiki chosa (Akitaken Honjoshi oyobi Yuzawashi ni okeru anketo kara)

    Energy Technology Data Exchange (ETDEWEB)

    Nogoshi, M. [Akita University, Akita (Japan). College of Education; Kabutoya, S.

    1996-05-01

    Consciousness for the earthquake was investigated by questionnaire surveys made in Honjo City and Yuzawa City, Akita Pref. in October 1995 twelve years after the Nihonkai Chubu Earthquake (M=7.7) in May 1983. The survey was conducted in terms of 27 items including personality, memory, knowledge/interest, psychology/action, mental attitude/preparations, wishes for researchers and administration, etc. Also included were the items on the Great Hanshin-Awaji Earthquake and the earthquake blank areas. The number of distributed questionnaires and the recovery rate of them are 1500 and 79.2% in Honjo City, and 1700 and 84.7% in Yuzawa City. From the survey, it was found that people have a lot of knowledge of and high interest in the earthquake and well remember it, and a lot of people know of tsunami, liquefaction phenomena, and the earthquake blank area. Further, they are afraid of earthquakes and think of their actions to be taken in case of earthquake. However, most people are little prepared for earthquakes. Important future subjects were suggested for the study of disaster prevention measures. 13 figs.

  3. Report of the 14th IFAC symposium on automatic control in aerospace; Dai 14 kai IFAC `koku uchu ni okeru jido seigyo symposium` shusseki hokoku

    Energy Technology Data Exchange (ETDEWEB)

    Nakasuka, S. [The University of Tokyo, Tokyo (Japan)

    1999-04-05

    This is the report of the 14th International Federation of Automatic Control (IFAC) symposium on automatic control in aerospace, held on August 24 to 28 1998 at National Seoul University, ROK, by the author who participated in the symposium. This symposium is held by the IFAC`s Aerospace Technical Committee once in every 3 years for automatic control mainly for aerospace, in particular navigation, guidance and control of aircraft, satellites, rockets and the like. A total of 65 papers were presented to 25 sessions, with a total of 106 attendees. There were a number of attendees from Japan, and Russia sent an unusually large number of attendees. The general lectures covered the topics of, e.g., attitude and orbit control of satellites and the like, control of aircraft, guidance and control of missiles, navigation of aircraft and space aircraft, space robotics, failure diagnosis, basic theories on control, and system development. Reports on development and results of actual projects accounted for the majority in the sessions for control of satellites, rockets and the like. (NEDO)

  4. Optimization of man-machine roll allocation in automatic systems; Jidoka system ni okeru hito to kikai no yakuwari buntan no saitekika

    Energy Technology Data Exchange (ETDEWEB)

    Yamasaki, H. [Yokokawa Electric Corp., Tokyo (Japan). Research and Development Lab.

    1996-08-10

    Bearing reliability and safety of automatic systems in mind, man-machine roll allocation in the operation of facilities is examined, and the optimal roll allocation is proposed. The outline of the method for man-machine roll allocation is given in process instrumentation system, robotized assembly plant, railroad operation control system, and passenger airplane operation control system. The types of man-machine roll allocation in automatic system is divided into normal and emergency cases. Improvement in the total reliability of man-machine system can be expected by man-machine mutual complementary roll allocation. The core of the intelligent support system for emergency is the growing knowledge base, and the system performs intelligent support automatically or with the support of human in an emergency. For smooth man-machine information interchange at man`s own will, logical difference between man and machine must be adjusted in the man-machine interface. 8 refs., 2 tabs.

  5. Regulations concerning open access to transmission grid in U.S.. Analysis of order No.888; Beikoku ni okeru open access no hokisei. Order No.888 no kento

    Energy Technology Data Exchange (ETDEWEB)

    Maruyama, M.

    1999-02-01

    Recently, countries aiming at deregulation of the electricity supply industry tend to choose `open access models` that allow final customers the freedom to select suppliers. For example, in 1996, U.S. Federal Energy Regulatory Commission (FERC) issued Order No. 888, which requires electric utilities to open their transmission grid for third parties. However, there are a lot of issues to be addressed before we adopt such models in our country. In this paper, we discuss open access of the transmission grid from the view points of utility regulation, taking account of the debates over regulations on grid access, especially concerning Order No.888 and previous laws and regulations in the United States. The results are: 1. At the end of 1980s, laws and regulations were established to require electric utilities to open their transmission grid for third parties. However, propriety of the wheeling order was decided on a case-by-case basis before the enactment of Order No.888. 2. Under tile provisions of Order No. 888 issued in 1996, electric utilities are required to open their transmission grid any time by request. Nevertheless, that obligation is limitative because (1) the electric utilities have a preferential access to the grid, (2) eligible customers can access to the grid only if there is available transmission capacity. Hence, one of the critical issues to be addressed is how to calculate their available transmission capacity. (author)

  6. Practical risk estimation method and applications of aerial photographs for preventing slope disasters in railways; Tetsudo ni okeru shamen saigai to sono taiosaku

    Energy Technology Data Exchange (ETDEWEB)

    Sugiyama, T.; Noguchi, T. [Railway Technical Research Institute, Tokyo (Japan)

    1997-12-01

    This paper, upon describing the actual states of slope disasters in railways, indicates the current status of measures taken to prevent these disasters. It also describes the measures to prevent slope disasters occurring currently and the future prospect thereof, focusing on the following two points: (1) a recently developed method for evaluating risks in banking and excavation slopes, and (2) an information control technology to prevent disasters of slope collapses by using remote sensing system and attempts on a method to estimate locations with risks of collapse occurrence by using the former information control technology. Development has been made of a method to evaluate rain disaster risks, which can identify quantitatively rain resisting strength of slopes, reflect the rain resisting strength on the operation rules, and estimate disasters on the real time basis. The method has been developed by using a statistic method to estimate the collapse critical rain amount as an exciting cause from predisposing cause of banking and excavation slopes, based on the record of nationwide disasters. Discussions were given on application of latest remote sensing technologies to slopes along railroads. Furthermore, an attempt was implemented on estimating collapse risks along railroad lines, utilizing slope information extracted from the above application of the remote sensing technologies. 13 refs., 12 figs., 7 tabs.

  7. Integrated practical technology for rationalization of production system in Miike coal mine; Seisan kozo kaikaku no tame no sogo shien gijutsu (Miike tanko ni okeru gijutsu kaikaku)

    Energy Technology Data Exchange (ETDEWEB)

    Furukawa, H. [Mitsui Mining Co. Ltd., Tokyo (Japan)

    1997-10-25

    This paper describes the improvement of production structure and the reduction since the latter half of FY 1990 in the Miike Coal Mine. The annual production was reduced from 4.5 to 2.35 million tons. The rationalization strategy is composed of the increase in productivity with intensive faces by introducing high performance mining facilities (MHP) and by modifying mining method, the mechanization of driving works, the simplification of underground structures, the reduction of indirect costs, and the rationalization of surface management departments. Faces were reduced to one or two by the MHP, and high operation rate and energy saving are achieved using self-advancing frames. Face moving period was reduced by rotating the MHP within the underground. Labor-saving of belt conveyors was achieved using built-up frames. For the gallery driving, a base gallery was excavated before production, and level driving was expanded through the base gallery. High-speed and systematic face driving was realized through in-seam driving by operating road header without using blasting. To avoid the decrease in operation rate due to unexpected faults or spring waters, early grasping system of face conditions was established, and environmental arrangement was enriched. The efficiency was improved from 96 in FY 1988 to 159 t/person{center_dot}month in FY 1995. 4 refs., 4 figs., 1 tab.

  8. Historical overview of geophysical exploration for hydrocarbon prospecting in Japan; Nippon no sekiyu kogyo ni okeru butsuri tanko gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tamura, Y. [Japan Petroleum Exploration Corp., Tokyo (Japan)

    1998-08-01

    This paper describes a historical overview of geophysical exploration for hydrocarbon prospecting in Japan. In general, history is divided into eras by the qualitative change. In the case of geophysical exploration, the history is desired to be divided by considering the both of qualitative change in the technology and that in the practical application. In the early time of geophysical prospecting, gravitational exploration, magnetic exploration, seismic refraction method and seismic reflection method were elementarily and successfully tried. In the era of classical geophysical exploration, seismic reflection method and gravitational/magnetic methods were basically completed, and accumulation structures of potential petroleum were discovered around existing oil fields. In the era of systematic geophysical exploration, techniques of underground geological reflection profiles were completed with digitalization, and systematic petroleum exploration was conducted. In the era of modern geophysical exploration, 3D seismic was put into practice, and the inversion accuracy was improved, in which the geophysical exploration could be contributed jointly with the geological techniques. New development era of geophysics is expected. 31 refs., 10 figs., 5 tabs.

  9. Role of simulation model in petroleum exploration. Have we developed new ideas for exploration; Sekiyu tanko ni okeru simulation no yakuwari. Hatashite wareware no shikoho wa kawattanoka

    Energy Technology Data Exchange (ETDEWEB)

    Nakayama, K. [Japex Jeoscience Institute, Tokyo (Japan)

    1998-01-01

    This paper describes a role of simulation model in petroleum exploration based on geology. Geology is based on inductive method in which a scientific fact can be extracted and estimated from the pile of descriptive records. Such an inductive method is called a backward model. While, geophysics is based on a deductive method in which a physical or mathematical model is developed assuming a uniformitarialism in the past before extracting a scientific fact through the model calibration. Such a deductive method is called forward model. Introduction of simulation model has been useful for petroleum exploration due to its deductive property. However, some conceptualization and simplification are introduced in such a method. Therefore, its accuracy is still far from the fact. However, objective concept can be obtained to certain degree. Simulation modeling is one of a significant methods by which petroleum exploration can be activated and new ideas can be created in the field of petroleum geology. It is required to apply the simulation modeling by checking it using conventional inductive method. 12 refs., 7 figs.

  10. Regional unification of energy in North America. ; NAFTA and its related matters. Hokubei ni okeru energy no chiiki togo. ; NAFTA to sono kanren ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    1993-08-01

    The present paper reported energy-related items in the NAFTA. Being discussed among the US, Canada and Mexico, the NAFTA aims at withdrawing the trade barrier, relaxing the investment limitation and protecting the right of intellectual ownership. The foreign enterprises are influenced in both import tax cutdown and original home regulation. Main points which are related to the energy in Mexico are as follows: Mexico reserves the property rights of natural gas and pipelines while the PEMEX maintains the oil export/import and transport rights. In the power generation field, the CFE (Committee for Federal Electricity) owns the power generation and selling rights while the NAFTA approves the foreign investment in the power generation facilities. As per performance contract which forms a special field, incentive is given to the foreign enterprises when succeeding in oil exploration. In the petrochemical field, there exist basic petrochemical products in which the foreign investment is prohibited. A 100% participation of foreign capital is allowed in all other products than the above ones. How the foregoing changes influence the foreign investment is uncertain.

  11. Local corrosion of magnesia-chrome refractory at slag-metal interface; Yoyu slag metal kaimen ni okeru magnesia / chrom shitsu taikabutsu no kyokubu sonsho

    Energy Technology Data Exchange (ETDEWEB)

    Tao, Z.; Mukai, K.; Ogata, M. [Kyushu Inst. of Tech., Kitakyushu, Fukuoka (Japan)

    1998-09-01

    The corrosion mode of refractory depending on the chemical dissolution of molten slag-metal, a component of refractory is classified mainly into the corrosion of inner slag phase body and inner metal phase body, and local corrosion at slag surface and slag-metal interface, and local corrosion at the interface of different type of refractories. Among them, local corrosion occurring at the slag-metal interface is a serious problem that effects the life of refractory, and these recent years research regarding the prevention of this type of local corrosion has been closed up. So far, number of researches regarding the local corrosion of solid oxides at slag-metal interface has been carried out. However, these are all based on close single component and research regarding the practical oxides with multiple components and multiporous characteristic has not been carried out. In this research, practical magnesia-chrome refractory (CaO-SiO2-Al203-FetO) slag-metal system is described and revelation of local corrosion phenomena at slag-metal interface was studied. 17 refs., 14 figs., 2 tabs.

  12. Fiscal 1998 research report. Feasibility survey on offshore wind power generation in Japan; 1998 nendo chosa hokokusho. Nippon ni okeru yojo furyoku hatsuden no donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey studied the feasibility of large-scale offshore wind power generation in Japan. Attempt was also made on preparation of outline maps of offshore wind around Japan. The cost of future offshore wind power generation systems is roughly dependent on technical issues and environmental issues. As technical issues, 'installation site,' 'foundation,' 'system interconnection' and 'maintenance/management' were summarized based on applications in Europe. As a result, it was clarified that technical issues can be solved with existing technologies to a certain extent, however, those relate to economical problems closely. The previous environment impact assessments say that wind power generation has no problems on the environmental issues. As relatively strong wind coastal areas, the outline maps of offshore wind point out Western Hokkaido area, Japan Sea area of Tohoku district, Pacific ocean area of the central part of Honshu, Genkai Nada area, Western Kyushu area and Southwest islands area, and suggest that these areas are promising for offshore wind power generation. (NEDO)

  13. Composition dependence of the rate of bainitic transformation in Cu-Zn-Al alloys; Cu-Zn-Al gokin ni okeru bainite hentai sokudo no gokin sosei izonsei

    Energy Technology Data Exchange (ETDEWEB)

    Tabuchi, M.; Marukawa, K. [Hokkaido University, Sapporo (Japan). Faculty of Engineering

    1998-04-20

    The bainitic transformation is known to have an intermediate nature between the martensitic transformation and the diffusional transformation, while its transformation mechanism has not yet been clarified precisely. If this transformation involves lattice shearing like the martensitic transformation, it should take place more easily in those alloys which have a higher tendency to transform martensitically. On this expectation, the composition dependence of bainitic transformation kinetics has been studied in Cu-Zn-Al alloys. Especially, the relation between the martensitic transformation temperature (Ms) and the bainitic transformation rate was examined. The transformation process was traced by measuring the electrical resistivity of specimens during aging. It was found that the transformation rate is higher in those alloys having a higher Ms temperature. The activation energy for the process, obtained from its temperature dependence, is independent of the alloy composition and roughly equal to that for solute diffusion in the parent alloy. This indicates that the transformation is controlled by diffusion of solute atoms. The composition dependence of the bainitic transformation rate is discussed in terms of a diffusion controlled growth theory. 15 refs., 7 figs., 3 tabs.

  14. Continuous cooling transformation behavior for heat treatment of spheroidal graphite cast iron. Kyujo kokuen chutetsu no netsushoriji ni okeru renzoku reikyaku hentai kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Nakata, T.; Matsumoto, H. (Shibaura Institute of Technology, Tokyo (Japan)); Kasugai, T. (National Research Institute for Metals, Tsukuba (Japan)); Koyama, M. (Automobile Foundry Co. Ltd., Yokohama (Japan))

    1992-08-25

    In order to study basic heat treatment properties of spheroidal graphite cast iron, the continuous cooling transformation(CCT) diagrams for the material equivallent to FCD700 under various austenitized conditions were obtained. There were 4 kinds of austenitized conditions varying from 1123K and 420s to 1323K and 1,800s. Eight kinds of cooling time from the austenitized temperature to 773K ranged from 6s to 4,000s. The transformation temperature was measured by a thermal expansion method. When the austenitized temperature was increased from 1123K to 1323K, ferrite and pearlite transformation regions moved a little in the CCT diagrams and the martensite transformation temperature decreased from 493K to 458K. The bainite region in the CCT diagrams disappeared at the austenite temperatures above 1223K. The nucleation sites of ferrite and pearlite in the spheroidal graphite cast iron were generated at grain boundary between austenite and graphite but not at grain boundary between austenites. The reason of such phenomena was also studied. 10 refs., 8 figs., 2 tabs.

  15. Isothermal transformation behavior in 12%Cr-0.3%C steel; 12%Cr-0.3%C ko ni okeru koon hentai kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Mikami, M. [Japan Casting and Forging Corp., Kitakyushu (Japan); Tsuchiyama, T.; Takaki, S. [Kyushu Univearsity, Fukuoka (Japan)

    2001-01-01

    In order to get fine grain of large martensitic stainless steels products, it is available to use the isothermal transformation before the austenitizing. When 12%Cr-0.3%C steel is subjected to the full solution treatment and following isothermal transformation at 900-1,020K, it is observed that the microstructures are affected by the isothermal ageing temperature. The microstructure transformed isothermally at 1,020K is the full eutectoid structure where carbides precipitate homogeneously. On the other hand, the microstructure transformed at 900K is the mixed heterogeneous structure: the eutectoid structure where carbides precipitate densely around the edge of prior austenite grains and the ferrite structure where carbides hardly precipitate in the center of prior austenite grains. These phenomena are concerned with the decreasing in carbon content in the untransformed austenite as the eutectoid transformation progresses. The amount of decreasing in carbon at 900K is larger than at 1,020K, which causes the shortage of carbon in austenite in the last period of isothermal transformation. In the case of the isothermal transformation at 900K, the reason of why there are the ferrite structures with no carbide in the center of prior austenite grains is that the massive transformation is induced by the shortage of carbon in untransformed austenite. (author)

  16. Effective range of electrical stimulation in brain silica preparation; No slice hyohon ni okeru denki shigeki koka han`i no kento

    Energy Technology Data Exchange (ETDEWEB)

    Takimori, T.; Ogawa, T.; Nishida, M. [Akita University, Akita (Japan)

    1997-08-20

    In order to examine the confines of electrical stimulation in layer 2/3 of visual cortex in the brain slice preparation, we estimated the effective range of the stimulation based on the excitatory postsynaptic potential (EPSP) evoked in layer V neuron which receives input from layer 2/3. For this purpose, we recorded and compared EPSPs amplitudes evoked by stimulations at directly over site of recording electrode and lateral site in layer 2/3. Since the EPSP increased linearly with stimulus intensity before the saturation, it was considered that the EPSP correlates with the number of projecting neurons in area directly excited with the stimulation. Then we formed the region model by which we can get the ratios between the neuron numbers in areas excited by different sites stimulations against the stimulus effective ranges. And in the stimulus intensity for action potential threshold of layer 5 neuron, we evaluated the effective range for the relative values of EPSPs to be produced with the stimulations of 250{mu}m lateral site and directory over site. In the model, the ratio increased monotonically with the effective range and in the case of 250{mu}m for the effective range, the ratio between those EPSPs was less than the value in the model. These results led the conclusion that the effective range of the intensity for layer 5 neuron to generate the output is confined within 250{mu}m from directly over site, that is, within layer 2/3. 7 refs., 11 figs., 1 tab.

  17. Survey of the trend of technical development and industrial policies in Asian countries; Asia shokoku ni okeru gijutsu kaihatsu no doko to sangyo gijutsu seisaku ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A sharp rise in industrial productivity in Asia countries indicates a rising level of R and D technology. Since Japan has not clearly grasped the R and D ability in these countries, it has not given appropriate personnel/material R and D support to them. Therefore, for the purpose of exactly grasping the R and D ability of Asian countries (Korea, Taiwan, the Philippines, Indonesia and India) and studying an effective and appropriate method for R and D cooperation, a survey was conducted of R and D potentials in Asia and R and D support policies of the countries. As a result of the survey, the following are taken up as items to be considered: promotion of exchanges between Tsukuba, etc. in Japan and research/university towns and science parks being constructed in lots of countries, participation of private companies in high-tech joint work in cooperation with Japan, sending information from Japan using internet, etc. and exact grasp of needs at partner side, cooperation given to new comers without asking for research results (use of OB researchers, etc.) 25 refs., 39 figs., 59 tabs.

  18. Preventive design review as quality assurance and further task at Kawasaki Heavy Industries, Ltd.; Kawasaki Juko ni okeru jizen kensho no torikumi to kongo no tenkai

    Energy Technology Data Exchange (ETDEWEB)

    Minakata, S.; Okazaki, S.; Nishimoto, T.; Saeki, H.; Niguma, Y. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1999-12-01

    At Kawasaki Heavy Industries, Ltd. (KHI), to reduce the risk in manufacturing and contribute to our company management, the most useful method of our Quality Assurance (QA) activities is preventive verification by design reviews (DR). During a design review, we effectively use the abundant experience of our company in the technologies of design, manufacturing and management to prevent failures resulting from the upper processes, such as design. As a direct result of this activity (GRP-50 and 75), failure costs have been greatly reduced. In the future we will continue to evolve our QA activities backed by preventive verification, aiming at linking Total Quality Management (TQM) to management in order to progress our company management and business process. (author)

  19. Origin of the latest miocene alkaline rocks from Oki-dogo island, SW-Japan; Oki togo ni okeru makkichushinsei oki arukari kazanganrui no seiin

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, S. [Tohoku Univ., Sendai (Japan)] Sawada, Y. [Shimane Univ., Matsue (Japan)

    1998-05-05

    Volcanic rocks, which erupted in later stage Cenozoic, are distributed widely in Oki-Dogo located at 60 km off Simane peninsular in the sea of Japan. In advanced stage Miocene, alkaline volcanic group rocks such as shoshonite, trachybasalt and rhyolite had erupted. These rocks are classified into Oki-trachyte, rhyolite, Hei-tracyte and quartz rhyolite from the bottom of the stratum. Rhyolite group rocks are classified into two groups on geological features, rock`s descriptions and chemical compositions. It was clarified that the rhyolite group had a unique composition change that the components such as Fe, Y, Ce, Pb, Ba, Nb, Rb, Zr, Th, changed from 1.1 times to several times in spite of the Si content almost without changing. On the basis of these results, the author of this paper proposed the models for partial melting and magma mixing of the earth`s crust materials at the lowest co-melting point to solve the origin of two groups of rhyolite. 34 refs., 11 figs., 8 tabs.

  20. Horizontal wells in the Daleel field 2nd development campaign; Dariru yuden no niji kaihatsu ni okeru suihei koi ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Yanagisawa, K. [Japex Oman Ltd., Tokyo (Japan)

    1995-11-01

    The horizontal wells excavated at various places in the world have been carried out at an increasing tempo during recent some years. In particular, Oman has a number of small scale petroleum wells and a task on what means their oil production should be increased, therefore the horizontal excavation is judged to be much optimum. In this Daleed field 2nd development mainly consisting the prolonged region development ranged from north to south, all developing oil wells were determined to excavate with the horizontal excavation method and 10 wells were planned to excavate from the judgement of the possibility of low cost, in addition to the advance of the horizontal excavation technique. The excavating operation was conducted from July 1st, 1994 to March 22nd, 1995, and was finished without any failures. Test results of all oil wells are good, and the mean value of the initial production indices of the horizontal wells were about 3 times to that of vertical wells. And, it made possible to produce petroleum from the areas impossible in the vertical wells, because of presence of gas gap. Adoption of the horizontal well increased early oil production rate, which brought a lot of contribution to economics of the project. 3 refs., 9 figs., 1 tab.

  1. Study on the swirling flow field in a rotating cylinder. 3rd Report. Experiment; Kaiten kannai ni okeru senkai nagareba ni kansuru kenkyu. 3. Jikken

    Energy Technology Data Exchange (ETDEWEB)

    Kishibe, T. [Hitachi, Ltd., Tokyo (Japan); Kaji, S. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    2000-02-25

    In the previous papers, the swirling flow field in a rotating hollow turbine shaft was solved using computational fluid dynamics. It was observed that a large-scale spiral vortex existed at a place where the swirling flow turned radially outward. In this report, the pressure fluctuations in the swirling flow field are measured. The main part of the internal cooling air system of a gas turbine is used as the experimental apparatus. A specially devised liner in inserted inside the hollow turbine shaft and ten pressure sensors are embedded axially and circumferentially in the liner to measure the unsteady wall pressures. The pressure fluctuations which have the same characteristics as the rotating spiral vortex predicted in the numerical results are captured. The amplitude is great at the sensors near the place where the vortex was predicted in the numerical results and the precession frequency of the rotating spiral vortex is in close agreement with the calculated frequency. (author)

  2. Study on the impact assessment for the life cycle assessment (LCA); Kankyo fuka bunseki ni okeru impact assessment ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report describes the impact assessment which is an important step for LCA. For classification of the impact assessment, the existing literature was reviewed and a skeleton for the classification was proposed. The weighting factors for nine selected impact categories, which were used to calculate environmental load point (ELP) for the valuation, were obtained for two overseas groups, i.e., students of Amsterdam University and SETAC Europe members. It was found that the former provided the similar trends to general Japanese, however that the latter gave high weighting in the global warming and depletion of ozone layer. The ELP was proposed and applied to automatic washing machine, coffee maker, waste incineration power generation system, and co-generation system. As a result, its effectiveness was demonstrated. This report also describes problems for the LCA of thermal and material recycling of PS trays. 99 refs., 96 figs., 73 tabs.

  3. Investigation into the analysis method of total ecobalance in chemical industry products. 3; Kagaku kogyo seihin ni okeru total eko balance no bunseki shuho ni kansuru chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of establishing a total life-cycle ecobalance analysis (LCA) method, the paper studied making of a general computer program for chemical industry products. The study has been made on general-purpose plastics (PET/PSP (polystyrene paper)) since fiscal 1993 aiming at making the CO2 emission computing program covering the entire process of production from extraction of raw materials through waste disposal. In fiscal 1995, the following were conducted for enhancement of generalization of the method: expansion of environmental load items and increase in validity of the concept, and expansion of database. Notice was taken of not only CO2 but SOx, NOx and water quality load items. The survey was made on the recycling situation in Japan and abroad and the PET recycling plant , and environmental load item data are collected to expand database. The program was verified by analyzing an example of reusing PET bottle to carpet, and one-step development can be made toward the establishment of the method. Moreover, an analysis was made for the environmental assessment of the related programs abroad, and a tentative original plan can be proposed for the standardization of environmental load analysis and the integrated assessment method. 39 refs., 130 figs., 76 tabs.

  4. Investigational study of the CO2 balance in high temperature CO2 separation technology; Nisanka tanso koon bunri gijutsu ni okeru CO2 balance ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    An investigational study was conducted to clarify the adaptable environment and effectivity of technologies of high temperature separation/recovery/reutilization of CO2. In the study, data collection, arrangement and comparison were made of various separation technologies such as the membrane method, absorption method, adsorption method, and cryogenic separation method. With the LNG-fired power generation as an example, the adaptable environment and effectivity were made clear by making models by a process simulator, ASPEN PLUS. Moreover, using this simulator, effects of replacing the conventional steam reforming of hydrocarbon with the CO2 reforming were made clear with the methanol synthesis as an example. As to the rock fixation treatment of high temperature CO2, collection/arrangement were made of the data on the fixation treatment of the CO2 separated at high temperature into basic rocks such as peridotite and serpentinite in order to clarify the adaptable environment and effectivity of the treatment. Besides, a potentiality of the fixation to concrete waste was made clear. 57 refs., 57 figs., 93 tabs.

  5. Numerical analysis of viscoelastic start-up flow in abrupt contraction channel; Kyushukusho ryuro ni okeru nendansei ryutai no start up nagare no suchi keisan

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, T.; Nakamura, K. [Osaka University, Tokyo (Japan). Faculty of Engineering

    1998-10-25

    Start-up flows of viscoelastic fluids in a two-dimensional 4 to 1 abrupt contraction channel is numerically studied and the transient behavior of viscoelastic fluids is discussed. The multi mode Leonov model is applied to describe the rheological properties of the viscoelastic fluid. The numerical simulation has been carried out for two Weissenberg numbers. The following results are obtained from the present analysis: The corner vortices develop with time and restrict the velocity gradient to relax the growth of the stress field. The circular secondary flow works as a stress relief mechanism. The overshoot of the stress growth is observed at the high Weissenberg number and is not done at the low Weissenberg number. This phenomenon is caused by the unsteady elongational property of the fluid. 15 refs., 9 figs.

  6. Numerical calculation of viscoelastic flows through eccentric abrupt contraction; Henshin kyushuku shoryuro ni okeru nendansei ryutai no nagare no suchi kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, K.; Mori, N.; Matsumura, K. [Osaka University, Osaka (Japan). Faculty of Engineering

    1997-04-25

    Numerical simulations of viscoelastic flows through an eccentric four-to-one abrupt contraction are carried out using the Giesekus model. The SMAC (Simplified-Marker-and-Cell) method is used to analyze the three-dimensional flows. The velocity profiles along the path line passing through the center of the exit exhibit an overshoot near the entry section, and at high Weissenberg numbers an undershoot follows the overshoot. The magnitude of the stress along the same path line has a peak near the entry, section, and its slow relaxation process indicates that a large downstream length is necessary for fully developed stress conditions to exist. The peak is lower than that for the flow through the concentric four-to-one abrupt contraction ; the decrease in the peak amplitude is understood to be due to the distortion of the path line in the eccentric geometry. A corner vortex, the height of which is a maximum at the widest corner, grows as the Weissenberg number increases. Furthermore, the tangential flow toward the widest section inside the vortex is determined. 19 refs., 10 figs.

  7. Education for hydraulics and pneumatics in Kanazawa University, Department of Human and Mechanical System Engineering; Kanazawa Daigaku Ningen Kikai Kogakuka ni okeru yukuatsu kyoiku

    Energy Technology Data Exchange (ETDEWEB)

    Matsui, Y. [Kanazawa University, Ishikawa (Japan). Faculty of Engineering

    2000-03-15

    The above-named department was established in 1996. It advocates, standing on the basis of mechanical engineering, 'adaptation with man,' 'symbiosis with society,' and 'harmony with nature,' and, under these mottos, aims to bring up engineers who are able to create technologies in the field of mechanical engineering. There is no independent subject for fluid power. Relative subjects are the science of flows, thermodynamics and exercise, energy and environmental engineering, and nature and flow. Lectures are given using textbooks mainly. There is no subject that requires experiment on fluid power. It is hoped that teaching materials will be provided. Studies for graduation and master's theses are the 'suction performance of toroidal pumps' and the 'fluid force in, and flow coefficients of, spool valves.' Collaborative researches with industrial circles conducted so far involve the 'study of automotive vane pumps' and the 'suction performance of toroidal pumps.' It is difficult for subjects related to hydraulics and pneumatics to interest students greatly. To interest and attract students, it is felt, the concept like 'hydraulics and pneumatics signify power sources' which gives a tough and mighty impression should be replaced by a softer-tone expression like 'hydraulics/pneumatics and mechatronics and control.' (NEDO)

  8. Education for hydraulics and pneumatics in Yokohama University, Faculty of Engineering, Department of Mechanical Engineering and Materials Sciences; Yokohama Kokuritsu Daigaku ni okeru yukuatsu kyoiku

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Y. [Yokohama National University, Yokohama (Japan). Faculty of Engineering

    2000-03-15

    Described herein is education for hydraulics and pneumatics in Yokohama University. Department of Mechanical Engineering and Materials Science pursues to most efficiently produce high-quality products useful for human living and compatible with the environments, based on scientific and technological knowledge man has learned. This department has four professional education courses, materials designs, mechanical processes, hot fluid dynamics, and mechanical systems. An independent subject of hydraulic and pneumatic systems is provided for hydraulics and pneumatics. The lectures on mechatronics include those for digitally-, electronically/hydraulically- and electronically/pneumatically-controlled devices, and their characteristics. The related subjects include fluid dynamics, basic fluid analysis, applied fluid analysis, turbo machines, and automatic control. The postgraduate courses provide hydraulic and pneumatic engineering for, e.g., cavitation and unsteady flow through conduits, hydraulic/pneumatic driving and controlling, modeling and robust control of mechanical systems, and designs of fluid-controlling devices and actuators. The experimental courses include tests of centrifugal pump performance, measurement of pressure distributions on journal bearings, and tests of fluid flow through conduits. (NEDO)

  9. Application of information theory to the sensitivity analysis of cogeneration system performance; Johoryo no gainen ni yoru kojenereshon system ni okeru fuka deta eikyo bunseki

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, K.; Ishizaka, T.; Honnma, I. [Tokyo Electric Power Co., Inc. (Japan)

    1996-01-05

    Cogeneration system (CGS) is anticipated by department of energy to play an important role in environment preservation. Cogeneration system`s estimation is depended on the preconditions, heat and electricity load data. Since the recognition of heat and electricity load is difficult, efficiency in load data is demanded repeatedly for the evaluation of cogeneration system. Necessary load factors for the estimation of cogeneration system from the energy department`s point of view as well as what measure may become good while recognizing load factors are investigated in this paper. Based on this, a proposal is made by considering load factors of buildings as a standard for estimation of the system. Further fixed quantity assessment is made with the results of computer simulation. From the obtained results, following observations are noted. Recognization of total load capacity is become very important when base load is introduced considerable amount for houses. Load factor`s information is very important for hotel when heat and electricity are used in balance. It is concluded that irrespective of motor capacity, whole day load factor information is necessary for office buildings. 6 refs., 15 figs., 2 tabs.

  10. Optimum orbit and control of reflux ratio in the batch distillation; Bacchi joryu ni okeru kanryuhi no saiteki kido to seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Morimoto, Jun; Susuzki, Mutsumi [Tohoku University, Miyagi (Japan)

    1999-06-05

    In the batch distillation, optimum orbit of reflux ratio exists under evaluation function of utility cost minimum and product quantity maximum. Enormous repeat calculation was necessary in order to calculate such optimum orbit by maximum principle. In this paper, calculation method which corrects initial value of the Hamilton accompanying function is proposed. Optimum orbit is calculated by this calculation method and advance on recent computer in the real time, and there is it, and it would be able to control the reflux ratio. And, it is also possible reflux ratio optimum state variable control table beforehand. These control method become an operation which is truly optimum for evaluation function. (translated by NEDO)

  11. Application of numerical analysis method to jet engine combustion design. Jet engine yo nenshoki no sekkei ni okeru suchi kaiseki no tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Negoro, T.; Arai, M.; Kuyama, T.; Nakahata, T.; Hirokawa, M. (Kawasaki Heavy Industries, Ltd., Tokyo (Japan))

    1993-01-20

    This paper describes features and applications of numerical analysis for jet engine combustor design. The numerical analysis for flow fields in a combustor has set a limitation on objects to be analyzed for each component element in the combustor or each design element, and carried out the analysis upon selecting basic formulas and models. The numerical analysis is effective to predict qualitatively the effects on flow patterns in the whole combustor liner interior or temperature distributions in the combustor liner interior, but is not sufficiently effective for use as quantitative evaluation. An application suggested that a parallel shape is more preferable that does not squeeze a flow outlet on the outer side that can be expected of providing sufficiently large recirculation flow region, as a result of analyzing the flow patterns around fuel injection valves. Dump diffuser analysis revealed that the above shape is preferable in supplying air stably from the annulus part into the liner interior through air holes. It was verified that the analysis of flows in the combustor liner has identified features of the flows qualitatively. 4 refs., 13 figs.

  12. Effects of fuel and air mixing on WOT output in direct injection gasoline engine; Chokufun gasoline kikan ni okeru nenryo to kuki no kongo to shutsuryoku seino

    Energy Technology Data Exchange (ETDEWEB)

    Noda, T.; Iriya, Y.; Naito, K.; Mitsumoto, H.; Iiyama, A. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    The effects of in-cylinder charge motion and the characteristics of the fuel spray and piston crown shape on WOT output in a direct injection gasoline engine are investigated. The fuel and air mixing process in a cylinder is analyzed by computer simulation and LIF method visualization. As a result, the technical factors to achieve enough mixing in a DI gasoline engine equipped with bowl in piston optimized for stratified combustion are clarified. 7 refs., 9 figs., 1 tab.

  13. Numerical simulation of fuel sprays and combustion in a premixed lean diesel engine; Kihaku yokongo diesel kikan ni okeru nenryo funmu to nensho no suchi simulation

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, T.; Harada, A.; Sasaki, S.; Shimazaki, N.; Hashizume, T.; Akagawa, H.; Tsujimura, K.

    1997-10-01

    Fuel sprays and combustion in a direct injection Premixed lean Diesel Combustion (PREDIC) engine, which can make smokeless combustion with little NOx emission, is studied numerically. Numerical simulation was carried out by means of KIVA II based computer code with a combustion submodel. The combustion submodel describes the formation of combustible fuel vapor by turbulent mixing and four-step chemical reaction which includes low temperature oxidation. Comparison between computation and experiment shows qualitatively good agreement in terms of heat release rate and NO emission. Computational results indicate that the combustion is significantly influenced by fuel spray characteristics and injection timing to vary NO emission. 10 refs., 8 figs., 1 tab.

  14. Development of natural gas in the South American region and internationalization of a market thereof; Nanbei chiiki ni okeru tennen gasu kaihatsu to shijo no kokusaika

    Energy Technology Data Exchange (ETDEWEB)

    Niwa, N. [Japan Petroleum Development Association, Tokyo (Japan); Terada, S. [Mitsubishi Research Institute, Inc., Tokyo (Japan)

    2000-09-01

    Recently, natural gas development in the South American region is actively advanced. Especially, southern countries have formed the customs union 'Mercosur' (the South America south cooperation market), and an energy supply network such as the natural gas pipeline has been formed with the integration of the market. In this paper, a present state of development project, an installment balance situation, a production situation, a relation infrastructure and a trend of the market of natural gas in South America especially each country of the southern district are described. And, the introduction of foreign capital is also advancing with the restructuring related to the natural gas business in these countries. Therefore, those trends are also described. In the South American countries, Argentina has abundant natural gas reserves which is the next quantity to Venezuela, and has coped with the development of natural gas since early times. According to the prediction of future demand trend of natural gas, Argentina, Bolivia and Trinidad Tobago are mentioned as an exporter of natural gas, and Brazil and Chile are mentioned as an importer of natural gas. (NEDO)

  15. Motion analysis of human cervical vertebrae and injury mechanisms during low speed rear impacts; Teisokudo tsuitotsu ni okeru ningen no keitsui kyodo kaiseki to shogai mechanism

    Energy Technology Data Exchange (ETDEWEB)

    Ono, K. [Japan Automobile Research Institute Inc., Tsukuba (Japan); Kaneoka, K.; Inami, S.; Hayashi, K. [University of Tsukuba. Tsukuba (Japan)

    1998-05-01

    It is said that, as long as a head rest is used in an automobile, dilation of the cervical vertebrae will not extend the physiological range. However, neck injuries are still occurring frequently as a result of the rear collision accidents. This paper describes an experiment simulating low speed rear impacts by using ten volunteers for the purpose of clarifying the neck injury mechanism. Data taken by using a continuous X-ray photographing device were analyzed. The following points were made clear on features of collisions from comparison with normal cervical vertebral behavior: at a rear impact, the cervical vertebrae are subjected to action of axial compression force due to inertia of the neck, in addition to push-up of the body resulting in upward movement, and the force remains affecting the cervical vertebral behavior thereafter; the effect appears as a bending condition in the cervical vertebrae in the initial stage around 50 to 100 ms after the impact, and then transfers into dilation behavior; and this condition exceeds the normal physiologically movable range, particularly the movement of the winding center being abnormal, which is thought to involve in the mechanism of generating injuries in vertebral joints. 8 refs., 11 figs.

  16. Improvement of performance of non-equilibrium MHD disk generator by means of segmented loads; Hiheiko disk gata MHD hatsudenki ni okeru bunkatsu fuka ni yoru seino kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, H.; Okuno, Y.; Kabashima, S. [Tokyo Institute of Technology, Tokyo (Japan)

    1995-08-20

    The performance of non-equilibrium MHD disk generator with segmented loads is examined with {gamma}-{theta} two dimensional numerical simulations. The use of segmented loads is found to improve the generator performance when a low electron temperature plasma is introduced to the channel. The simulation results reveal the desired values of load resistances connected in upstream and downstream regions, respectively. The concept of the segmented loads is considered to be superior to rearranging seed fractions and load resistances. 10 refs., 6 figs., 2 tabs.

  17. Comparison of ER and MR actuators in terms of performance in ERMC high-precision positioning; ERMC koseido ichigime ni okeru ER/MR actuator no seino hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Saito, T.; Watanabe, H. [Tokyo Engineering Univ., Tokyo (Japan); Sugimoto, A. [Research Inst. of Industrial Safety, Tokyo (Japan)

    1999-01-15

    Although the characters of a (magnetorheological (ER) fluid are quite like those of a dispersed electrorheological (ER) fluid, MR differs from ER in that the change in shear stress that MR shows upon magnetic field application is scores of times greater than that ER shows and that MR can be used even when the voltage is low. In this lecture, antagonistic rotation type actuators working on ER or MR are caused to incline with the angle of inclination controlled by the ERMC system, and the two are compared in terms of the frequency of stoppage achieved. The ERMC system is a high-precision positioning system making full use of the variable flow characteristics of the Bingham plastic that is a functional fluid. (translated by NEDO)

  18. Pressure response of electrorheological suspension in a model ER damper; ER damper model ni okeru bunsanke ER ryutai no atsuryoku oto

    Energy Technology Data Exchange (ETDEWEB)

    Nakano, M.; Yonekawa, T. [Yamagata University, Yamagata (Japan). Faculty of Engineering

    1995-01-25

    This paper reports the examination result of the pressure response of an electrorheological suspension fluid (obtained when the particles of a strong acid ion-exchange resin are dispersed on silicon oil and whose rheological characteristics vary with the action in the external electric field) in an electrorheological (ER) damper model (experimental equipment consisting of an ER valve with plane parallel electrode and a piston cylinder). A rectangular wave voltage is applied to the ER valve to obtain the pressure fall components based on the steady ER effect of an ER fluid flowing between the plane parallel electrodes. The intensity of the electric field and the dependence on the flow velocity were formulated by an approximate function. The flow velocity dependency of this ER effect does not coincide with the theoretical analysis result based on a Bingham fluid model. The pressure in a cylinder presents the transient response of a first-order lag to the rectangular wave voltage input to the ER valve. The time constant value in this case can be explained by considering the compressibility of the residual air in the ER fluid. 11 refs., 11 figs.

  19. Study of the influence of microgravity on the biological cells and molecular level; Seitai saibo bunshi level ni okeru bisho juryoku no eikyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The shape of osteoblast, gene appearance, gene of rice blast, cellular fusion of plants, gravity acceptance mechanism of unicellular organisms, and physiological and immunity functions of mice were investigated under the microgravity condition. The influence of gravity on the vital reaction and the influence of microgravity on the crystallization of vital substances were also investigated. For the observation of osteoblast, the fluorescence dye reacted with Ca was well taken in the cells. The microgravity affected the stability of rice blast, but hardly affected the protoplast culture of mushroom. The reaction of ciliate against the gravity related to the specific gravity difference between cells and outer liquid. The level of adrenaline in blood of mice increased during the drop. The moving speed of trigger waves of chemical parallel slit formed at the BZ reaction under the microgravity became 60% to 80% of that on the ground. In the case of crystallization at the deposition agent concentration of 1% to 4%, the turbidity showing the degree of crystallization changed complicatedly. Nine processes of crystal growth were recognized. 21 refs., 55 figs., 1 tab.

  20. Traffic flow characteristics and analysis on weaving sections of the Hanshin Expressway. Hanshin kosokudoro ni okeru orikomi kukan no kotsu jittai to kotsuryu kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Makigami, Y. (Ritsumeikan Univ., Kyoto (Japan). Faculty of Engineering); Toyota, (Japan Highway Public Corp., Tokyo (Japan)); Matsuo, T. (Hanshin Expressway Public Corp., Osaka (Japan))

    1992-01-20

    The report is aimed at giving an idea about design of the weaving section or traffic plan, which describes the outline and the results of a series of traffic survay and capacity analysis on weaving section on the Central Loop and its neighboring section of the Hanshin Expressway in 1985 to 1990 by making use of both areal photographs taken from a helicopter and video recordings and which makes an effort to clear which area does the traffic jam caused by the narrow road affect on and how does the mechanism show while making search the characteristics of the traffic flow in a weaving section. Using these traffic data, the applicability of HCM-85 Weaving Capacity Analysis Method to the Japanese expressway is evaluated. It also makes a touch to the problems and study about analysis method of weaving section. 11 refs., 21 figs., 3 tabs.

  1. Combined process of pyrolyzer/combuster for gas production and power generation; Chugoku ni okeru chukibo hatsuden to toshi gas seizo no tame no fukugo process no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ooka, I. [The University of Tokushima, Tokushima (Japan); Ma, T.

    1997-10-30

    In China, they are using a lot of coal by direct firing for domestic cooking, space heating and industrial use. Therefore air pollution is the big problem in every cities in winter season. And at moment, they do not have enough infrastructure for supplying energy such as gas and electric power. There is a great need for facilities for supplying gas and electric power from coal in big cities with much less pollution. This paper d a combined process of medium size plant of gas production and power generation by using fluidized circulation bed pyrolizer and combuster, to contribute to the energy supply which greatly reduces air and water polution and coal consumption. 1 ref., 1 fig., 3 tabs.

  2. Design and construction of precast PC-slab for the `Tokai Obu viaduct`; Tokai Obu kokakyo ni okeru precast PC yukaban no sekkei to seko

    Energy Technology Data Exchange (ETDEWEB)

    Mizuguchi, K.; Murayama, A. [Japan Highway Public Corporation, Tokyo (Japan); Kitayama, K.; Yamashita, S. [P.S. Corp., Tokyo (Japan)

    1998-03-31

    This paper describes the construction of Toukai Obu viaduct completed in 1997. This viaduct is specified by use of PC slabs, length of 974.5m and design speed of 100km/h, and was constructed aiming at cost reduction and new rational structure. Precast PC (PCa) slabs prestressed in a direction of slab span were produced under severe quality control in a factory. The PCa slabs stocked in a factory were transported by trailer and specific frame to the construction site, and laid on steel bridge girders by crane. An RC loop joint method for PCa slabs was newly adopted as one of the lap splice methods of reinforcing bars which is superior in cost and maintenance to conventional slab connecting methods in a longitudinal direction of bridges with PC steel material. Because of less domestic applications, a cyclic loading fatigue test at fixed points was carried out using a small model to obtain fatigue proof stress and fracture morphology. A moving loading test was also carried out at an actual loading level using full-scale slab specimens to obtain fatigue proof stress and long-span slab behavior. 7 refs., 24 figs., 8 tabs.

  3. Perpendicular construction of bridge girder for long span suspension bridge under a rapid stream; Kyuchoryuka ni okeru chodai tsuribashi no hokoketa chokka tsuri koho no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Hirayama, J.; Sakamoto, M.; Nakao, T.; Koga, N. [Honshu-Shikoku Bridge Authority, Tokyo (Japan)

    1996-06-20

    Perpendicular construction of bridge girder for a long span suspension bridge, which is to be constructed over the Kurushima Channel, an international route, has been investigated. For the construction of suspension bridge over channels, the overhang construction is generally employed. Bridge girder perpendicular construction, in which unit girder block is lifted from a carrier barge and directly constructed by means of lifting beams located at main cable, is a superb method in terms of cost, time, and safety. It is necessary to stay the carrier barge during the anchoring of girder block and lifting beams. Mooring of the carrier barge is required under a rapid stream, which results in the trouble of under way ships. A propulsion positioning system has been developed for the bridge girder carrier barge, by which the position/propulsion of four thrusters equipped at each corner of the barge can be automatically controlled. Thus, the perpendicular construction of bridge girder has been developed, in which mooring is not required even under the rapid stream. The position of barge can be maintained within a range of {plus_minus}2.5 m even under a rapid stream with a speed of 3 kn. The quick joint can be certainly connected for about one minute in the horizontal movement within {plus_minus}2.5 m and vertical movement within 0.5 m. For this perpendicular construction, the construction time can be shortened to around 16 to 17 minutes, which has been usually taken for three hours. 2 refs., 17 figs., 4 tabs.

  4. Production planning support system using. Phi. NET in FA. FA bun prime ya ni okeru. Phi. NET oyo seisan keikau shien system

    Energy Technology Data Exchange (ETDEWEB)

    Igawa, Y.; Hibino, K. (Fuji Electric Co. Ltd., Tokyo (Japan))

    1991-08-10

    In response to a wide use of the production simulation for production scheduling in the domain of factory automation (FA), a system of a machining flexible manufacturing system (FMS) production line using a general-purpose distribution control system building tool {Phi}NET was developed by Fuji Electric. In this report, an outline of this system was introduced as to its constitution and performance. This FMS production line has functions of the production scheduling, the production simulation, and the production instruction. Among them, the {Phi}NET model, in which the network model called petri-net and the production rule were combined, was applied to the production simulation. Consequently, was provided a prospect that the {Phi}NET would be developed to an FA simulator with which a production engineer can build a model with his own field language and conduct a simulation. 4 figs.

  5. Microscopic damage of quasi-isotropic carbon/epoxy laminates at various temperatures; Kakuondo kankyoka ni okeru carbon/epoxy giji tohosei sekisoban no bishiteki sonsho

    Energy Technology Data Exchange (ETDEWEB)

    Kim, H. [Kyushu University, Fukuoka (Japan); Ogi, K.; Matsubara, T.; Wang, W.; Takao, Y. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

    1998-06-15

    Quasi-isotropic Carbon/Epoxy laminates under tensile loading are investigated to understand the effects of temperature on stress-strain response and damage progress including the interlaminar delamination growth behavior. The material system used is T800H/3631 and the stacking sequence is quasi-isotropic [0deg/45deg/-45deg/90deg]s. The transverse crack behavior is microscopically observed and its density is quantitatively measured by using an optical microscope under various loads at different temperatures, i.e., low (-100deg), room (25deg) and high (150deg) temperatures. The interlaminar delamination growth behavior is non-destructively examined by a scanning acoustic microscope (SAM). It is found that nonlinearity observed in the stress-strain response is caused by the large scale interlaminar delamination throughout the length of the specimen. The transverse crack propagation and interlaminar delamination growth behavior are obviously affected by the temperature environments. Characteristic transverse crack formation at the edge of -45deg layer under -100deg is pointed out and its mechanism is discussed with the use of shear coupling of an off -axis lamina. 10 refs., 16 figs., 1 tab.

  6. Study of installation of PV systems at campus; Campus ni okeru taiyoko hatsuden donyu ni kansuru kenkyu (taiyo denchi nomi wo secchishita baai no yobi kento)

    Energy Technology Data Exchange (ETDEWEB)

    Tsuboi, N.; Tanaka, H.; Okumiya, M. [Nagoya University, Nagoya (Japan)

    1997-11-25

    In terms of energy consumption, environmentality and economical efficiency in the case of installing the photovoltaic power system on the rooftop of the university campus, a comparative study was conducted with other power generation systems. As objects to be comparatively studied, selected were the all-electric type centralized space heating/cooling system, cogeneration system, nighttime heat storage system and centralized system with solar cells installed. The panel area of the PV system is 10,000m{sup 2} on the rooftop and 7,000{sup 2} on the outer wall. About data on solar radiation, average values obtained in Nagoya were used. Assessment was made in terms of energy consumption amount at the time of operation, system COP, emission amounts of CO2, NOx and SOx at the time of manufacturing and operation, initial cost, running cost, etc. As a result of the study, an effect of reducing global warming gas was admitted in the PV system. However, the initial cost of the solar cell panel was high, and the life cycle cost of the PV system was lower than other systems. 1 ref., 7 figs., 3 tabs.

  7. Heat pump using dual heat sources of air and water. Performance in cooling mode; Mizu kuki ryonetsugen heat pump no kenkyu. Reibo unten ni okeru seino

    Energy Technology Data Exchange (ETDEWEB)

    Ito, S.; Miura, N. [Kanagawa Institute of Technology, Kanagawa (Japan); Uchikawa, Y. [Kubota Corp., Osaka (Japan)

    1997-11-25

    When a heat pump is used for cooling purpose, it is possible to utilize different kinds of waste water as high-heat sources. However, these heat sources would have their temperatures vary with seasons and time in a day. Therefore, a discussion was given on performance of a heat pump when water and air heat sources are used for condensers during cooling operation independently, in series and in parallel, respectively. The air condenser shows an equivalent COP as compared with the water condenser when air temperature is lower by about 8 degC than water temperature. At the same heat source temperature, the COP for the water condenser indicated a value higher by about 0.6 than the case of the air condenser. A method to use condensers in parallel experiences little contribution from the air heat source, and performance of the heat pump decreases below the case of using the water heat source independently when the air heat source temperature becomes higher than that of the water heat source. In the case of series use in which a water condenser is installed in front and an air condenser in rear, its effect is exhibited when temperature in the air heat source is lower than that in the water heat source. Better performance was shown than in operating the water heat source independently. 2 refs., 9 figs.

  8. Comparison of performance between a parallel and a series solar-heat pump system; Solar heat pump system ni okeru heiretsu setsuzoku no seino hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Kanayama, K.; Zhao, J.; Baba, H.; Endo, N. [Kitami Institute of Technology, Hokkaido (Japan)

    1997-11-25

    In a solar heat pump system, a single-tank system was fabricated, in which a heat pump is installed in series between a heat collecting tank and a heat storage tank. At the same time, a double-tank system was also fabricated, in which two tanks are assembled into one to which a solar system and a heat pump are connected in parallel. Performance of both systems was analyzed by using measured values and estimated values. Heat collecting efficiency in the double-tank system is higher by about 13 points than in the single-tank system. Nevertheless, the coefficient of performance for the single-tank system is 1.03 to 1.51 times greater than that of the double-tank system. Dependency of the single-tank system on natural energy is higher by 0.3 to 3 points than the double-tank system. Putting the above facts together, it may be said that the single-tank system connecting the solar system and the heat pump in parallel is superior in performance to the double-tank system of the series connection. 3 refs., 5 figs., 2 tabs.

  9. Starting and stopping control on power conditioner in photovoltaic power system; Taiyoko hatsuden system ni okeru power conditioner no kido teishi seigyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Hirose, M.; Ishihara, Y.; Todaka, T.; Harada, K. [Doshisha University, Kyoto (Japan); Oshiro, H.; Nakamura, H. [Japan Quality Assurance Organization, Tokyo (Japan)

    1997-11-25

    Studies are made about the control of the power conditioner over the maximum power point tracking (MPPT) function in a photovoltaic power generation system. The analysis is conducted by means of computer simulation into the effect of a start/stop function added to the control of MPPT and the effect on the generation of power of the setting of parameters in the start/stop function. The reduction in output power due to difference between the actual operation point and the optimum operation point is evaluated by use of a load matching correction factor. In this simulation, it is assumed that the solar cell array consists of 13 rows in 5 parallel columns, is capable of a normal output of 3.149kW, has a panel tilted at 30 degrees, and faces due south. The power conditioner is assumed to be a system rated at 3kVA, equipped with system interconnection and back flow features. As a result, it is learned that the stop voltage should be set at 180V or lower and the steady voltage near 185.5V for a good result and that there is not much need after all for the start/stop technique. 2 refs., 8 figs., 2 tabs.

  10. Study on the simulation time increments for solar DHW heating systems; Taiyonetsu kyuto simulation ni okeru keisan jikan kankaku no kento

    Energy Technology Data Exchange (ETDEWEB)

    Sato, M.; Udagawa, M. [Kogakuin University, Tokyo (Japan)

    1997-11-25

    Calculation time intervals effective in simulating solar DHW systems were discussed, taking into account water temperature in a heat storage tank and calorific power in supplied hot water. The discussion was given on a direct heat collecting system in which heat passes through a heat collector from the bottom of the heat storage tank and returns to the center of the tank, and an indirect heat collecting system which has a heat exchanger built inside the heat storage tank at its bottom. The calculation was performed with time intervals of one to sixty minutes and five to forty-five layer divisions. The following results were obtained: because the calorific power of the hot water supplied is underestimated in the calculation if the calorific power of one hot water supply is extremely large, the calculation time intervals must be reduced to 1 to 15 minutes; cumulative calorific power of the hot water supply was found to show little variation if the number of division is greater than fifteen; and the daily cumulative effective heat collection amount shows very little variation due to the calculation time intervals, but errors from the measured value have decreased as the smaller the number of layer division in the direct heat collecting system, and as the greater the number of division in the indirect heat collecting system. 4 refs., 9 figs., 2 tabs.

  11. Necessity of irrigation for revegetation on reclaimed land with fly ash. Sekitanbai umetatechi ni okeru ryokuka no tameno kangai no hitsuyosei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Sekiyama, Tetsuo; Kozakai, Kazuki; Okabe, Katsumi.

    1989-02-01

    In view of the growing importance of revegetation measures of a reclaimed land with fly ash discharged from a coal burning thermal power plant, a study was made on necessity of irrigation in case of the positive execution of the above revegetation. This is a report of the above study. The conclusions of the study are as follows: (1) Comparing the available moisture amounts in terms of volume percentage of moisture, about 36% is for fly ash and about 34% for volcanic ash soil, but when fly ash is solidified, the above figure for fly ash becomes about 90% of that for volcanic ash soil. (2) The maximum water infiltration capacity of fly ash is 1/10-1/50 of that of volcanic ash soil and the surface run-off is much. The furrow or drip irrigation system is suitable. (3) The evaporation in fly ash is almost same as that in volcanic ash soil and the designed duty of water irrigation is considered to be 7-8mm/day (in case of cultivation of tangerine and pasture). (4) In case when the above reclaimed land is covered with volcanic ash soil, an aquifer is observed at the boundary layer between the surface soil coverage and the land. Hence draining measures such as underdrainage systems are desirable from the viewpoint of the growth of plants. 8 refs., 8 figs., 2 tabs.

  12. Land subsidence in the Saga plane due to water shortage in 1994; Saga heiya ni okeru 1994 nen ijo kassui to jiban chinka

    Energy Technology Data Exchange (ETDEWEB)

    Hachiya, Y.; Kitajima, J. [Saga Prefectural Government Office, Saga (Japan); Jinno, K. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1996-08-21

    This paper reports land subsidence in Saga Plane during the abnormal drought in 1994. Saga Plane is arranged with a table land with a height of 20 m or lower above sea level, an alluvial fan, an inundation plane, and a delta in that order, with a reclaimed land spreading in front thereof. Groundwater is utilized mainly for industrial use in the Saga district, with consumption of 12 million m{sup 3} per year in around 1975 and 3.5 million m{sup 3} per year in recent years. The Shiraishi district uses groundwater mainly for tap water supply and agriculture, with normal consumption of 600 to 900 m{sup 3} per year having risen to 2000 m{sup 3} per year in 1994 when the abnormal drought has been experienced. The Saga prefectural government has been conducting groundwater collection amount survey, groundwater level measurement and level survey every year. As a result of observations, annual maximum subsidence has stopped at 3.3 cm and subsidence volume of 1280 m{sup 3} as a result of reduced groundwater collection in the Saga area. The Shiraishi area had ground water collection greatly increased due to drought, with the annual maximum subsidence having reached 16.0 cm and the subsidence volume of 5.9 million m{sup 3}. 7 refs., 11 figs., 2 tabs.

  13. Population dynamics of bacteria for phosphorus removal in sequencing batch reactor (SBR) activated sludge processes. Kaibunshiki kassei odeiho ni okeru datsu rin tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Okada, M.; Ueno, Y.; Lin, C.; Murakami, A. (Tokyo University of Agriculture and Technology, Tokyo (Japan))

    1990-01-10

    As the phosphorus removal processes, chemical methods and biological methods are considered. This paper discussed a biological phosphorus removal method. Laboratory experiments of phosphorus removal in sequencing batch reactor (SBR) activated sludge processes were operated using synthetic waste water to clarify the effects of solid retention time (SRT) and organic substrates on the accumulation of bacteria having phosphorus removal ability (bio-P-bacteria). The accumulation of bio-P-bacteria was enhanced by large fluctuation in concentration of organic substances in the reactor fed in a short period of time under anaerobic condition. However, the accumulation did not be enhanced in the reactor operated with SRT less than 25 d. The specific growth rates of bio-P-bacteria were estimated to a range from 0.033/d to 0.035/d in the SBR activated sludge processes fed with glucose and polypeptone as substrates. Therefore, large SRT is necessary for the accumulation of bio-P-bacteria. 18 refs., 10 figs., 1 tab.

  14. Effect of applied synthetic auxin on root growth in plantlet propagation by cuttage and tissue culture; Sashiki to soshiki baiyo ni okeru gosei auxin rui no shiyo koka

    Energy Technology Data Exchange (ETDEWEB)

    Shoji, K.; Yoshihara, T. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-12-01

    The effect of synthetic plant hormone 4-C1-IAA and TFIBA on root growth in plantlet propagation was clarified by the cuttage and the issue culture of strawberry seedling production. A periwinkle, vine, and azalea are the effect of 4-C1-IAA on root growth, and a promotion effect was recognized for rooting and root elongation. The concentration of 4-C1-IAA in which the growth promotion effect of a root most appears varies depending on the species of a plant. The concentration of a periwinkle was 20 ppm, and that of an azalea was 2000 ppm. The growth promotion effect of a root in 4-C1-IAA and TFIBA was compared with IBA for an azalea. The result showed that 4-C1-IAA is the same in the effect as IBA and that TFIBA is higher than for IBA. The growth of a vine`s terminal bud was promoted by the effect of TFIBA on root growth, and the callus occurring when IBA was treated was not formed. The rooting of a strawberry was promoted by the effect of TFIBA on root growth. The combined use of TFIBA and BA promotes the growth of a side bud and forms a multi-bud plant. However, rooting was inhibited. The callus caused by the effect of BA on root growth could be suppressed through the combined use with TFIBA. 6 refs., 7 figs., 2 tabs.

  15. Fixed position holding control for self-propulsion barges under disturbance condition; Gairanka ni okeru jiko baji no teiten hoji seigyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Kijima, K.; Murata, W.; Furukawa, Y. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1996-04-10

    In direct hoisting work in suspension bridge construction, since a cable crane directly hoists a bridge beam block put on a barge on the sea, precise fixed position holding function is required for a barge. The control system was then designed on the basis of an ILQ control theory, and the effect of change in time constant as design parameter on fixed position holding performance was studied. In addition, the critical disturbance for fixed position holding control was studied through numerical simulation under various disturbance conditions using the above designed control system. As a result, in the design of control systems on the basis of an ILQ control theory, the precise control system could be designed by diminishing, in particular, the time constant for state variable around a z axis among time constants according to the extent of disturbance. The control performance was largely affected by response delay period from sensing of disturbance to beginning of control. 3 refs., 7 figs., 2 tabs.

  16. Flow characteristics of Hijiori HDR reservoir form circulation test in 1995; Koon tantai Hijiori jikkenjo ni okeru shinbu choryuso yobi junkan shiken (1995 nendo) kekka to ryudo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Fukushima, N.; Hyodo, M.; Shinohara, N.; Takasugi, S. [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan)

    1996-05-01

    This paper reports the result of a preliminary circulation test conducted in fiscal 1995 on a deep reservoir (at a depth of about 2200 m) in the Hijiori hot dry rock experimental field. One water injection well and two production wells were drilled to constitute a circulation loop, to which the circulation test was performed to investigate the flow characteristics thereof. The result revealed the following matters: total amount of injected water of 51500 m{sup 3} resulted in a total fluid recovery rate of about 40%; as a result of well stimulation given twice during the initial stage of the water injection, the continuity impedance in the vicinity of the injection well decreased largely (however, the continuity improvement upon the second attempt was considerably inferior to that from the first attempt); and increase in the water injection amount does not necessarily lead to increase in the production amount. The paper describes additionally that it is extremely difficult to interpret non-linearity between the injection and production amounts by using a model prepared previously with a main objective to analyze the Hijiori HDR circulation system. 1 ref., 9 figs., 1 tab.

  17. Analysis of the pressure response of high angle multiple (HAM) fractures intersecting a welbore; Kokeisha multi fracture (HAM) kosei ni okeru atsuryoku oto kaiseki ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Ujo, S.; Osato, K. [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Arihara, N. [Waseda University, Tokyo (Japan); Schroeder, R.

    1996-05-01

    This paper reports pressure response analysis on wells piercing a high angle multi (HAM) fracture model. In this model which is defined on a three-dimensional space, a plurality of slanted fractures intersect with wells at high angles (however, intersection of fractures with each other is not considered). With respect to the pressure response analysis method using this model, the paper presents a basic differential equation on pressure drawdown and boundary conditions in the wells taking flows in the fractures pseudo-linear, as well as external boundary conditions in calculation regions (a reservoir spreads to an infinite distance, and its top and bottom are closed by non-water permeating beds). The paper also indicates that results of calculating a single vertical fracture model and a slanted fracture model by using a numerical computation program (MULFRAC) based on the above equations agree well respectively with the existing calculation results (calculations performed by Erlougher and Cinco et al). 5 refs., 6 figs.

  18. Application of streaming potential method for detection of fractures in granitic rock; Kamaishi kozan ni okeru ryutai ryudo den`iho tekiyo shiken

    Energy Technology Data Exchange (ETDEWEB)

    Negi, T.; Yokoi, K.; Yoneda, Y. [Nittetsu Mining Co. Ltd., Tokyo (Japan); Senba, T. [Power Reactor and Nuclear fuel Development Corporation, Tokyo (Japan)

    1996-05-01

    Measurements were made using the streaming potential method for the purpose of investigating the expansion of hydration cracks, direction of their propagation, and the chaining of cracked surfaces, in the granitic rock. Tests were conducted by use of a bore hole in the gallery wall. The bore hole yielded approximately 400 liters of water per minute, the bore hole was closed and then opened, and the change with the passage of time in the spontaneous potential (SP) on the gallery wall was measured. At a spot 31.2m from the mine entrance, the SP dropped by 15mV simultaneously with the opening of the bore hole, and rose by 14mV simultaneously with the closure of the same. The phenomenon was true for other locations, that is, for the section from the mine entrance to a spot 9.0m therefrom, and for a section beginning at 15.0m and ending at 19.2m therefrom. No change in the SP was observed in a group of cracks with water springing out of the gallery roof, beginning at a point 40m and ending at a point 54m from the mine entrance. The result suggests the possible application of the streaming potential method to the investigation of cracks. 1 ref., 10 figs.

  19. 2D resistivity survey in complex geological structure area. Application to the volcanic area; Fukuzatsuna chishitsu kozo chiiki ni okeru hiteiko nijigen tansa. Kazangan chiiki deno tekiorei

    Energy Technology Data Exchange (ETDEWEB)

    Asakawa, S.; Ikuma, T.; Tanifuji, R. [DIA Consultants Co. Ltd., Tokyo (Japan)

    1996-05-01

    Introduced herein is an application of 2D resistivity survey to a volcanic rock area where the survey result is difficult to interpret because of its complex geological structure. In a dam site survey, main problems involve the permeability of water through faults and weathered, altered zones. At this site, a 2D resistivity survey was conducted, a 2D geological structure was deduced from the resistivity section, and the result was examined. It was found that resistivity distribution was closely related to hydrographic factors, but no obvious correlation was detected between rock classes and R, Q, and D. In conducting investigations into a section planned for a highway tunnel, it was learned that the problem was a volcanic ash layer to collapse instantly upon absorbing water, and the distribution of the ash layer, not to be disclosed by boring, was subjected to a 2D resistivity survey. The survey was conducted into the structure above where the tunnel would run, and further into the face, and studies were made about what layer was reflected by the resistivity distribution obtained by analysis. The result of the analysis agreed with the details of the layer that was disclosed afterward. 4 figs., 1 tab.

  20. Travel time and ray path computation in 2D-heterogeneous structures; Fukinshitsu kozo ni okeru jishinha soji oyobi hasen no atarashii keisan hoho

    Energy Technology Data Exchange (ETDEWEB)

    Fujie, G.; Kasahara, J.; Sato, T.; Mochizuki, K. [The University of Tokyo, Tokyo (Japan). Earthquake Research Institute

    1996-05-01

    Methods were studied for determining the initial travel time and ray paths with stability when an non-linear travel time inversion is performed in an inhomogeneous structure. The travel time calculation was based on Faria and Stoffa`s method. First, the 2-dimension space was sectioned by grids, and `slowness` was assigned to all the lattice points. Starting from the vibration source, travel time at each lattice point is sequentially calculated. This method calculates travel time for any structure without breakup. In this study, an algorithm more sophisticated than the method of Faria, et al., was developed, and the improvement of travel time calculation accuracy led to the accurate determination of the direction of incidence into the lattice points during the initial motion. The calculation of ray paths was effected by tracing back from the receiving points the incidence into the lattice points or by following back the ray paths to the vibration source. This method performs stable calculation for a heavily inhomogeneous structure and, with the algorithm being simple, do the parallel programming as well. 1 ref., 6 figs., 1 tab.

  1. Magnetotelluric investigation in and around southern part of Hidaka metamorphic belt in Hokkaido, Japan; Hidaka henseitai nanbuiki ni okeru MT kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Sato, H.; Utsugi, M.; Hirano, K.; Doi, T.; Nishida, Y.; Arita, K. [Hokkaido University, Sapporo (Japan)

    1996-05-01

    An MT observation was conducted in the Hidaka district, Hokkaido, for the estimation of the 2D resistivity structure in the southern part of the metamorphic belt, when frequencies of the VLF, ELF, and ULF bands were used. An approximately 42km-long traverse line was set to cross the Hidaka metamorphic belt from east to west. As for the observation points, 48 VLF points, 16 ELF points, and 4 ULF points were provided. During the data processing, impedance tensor was calculated in the frequency domain for the determination of the apparent resistivity relative to frequency and the phase difference. As the result, it was found that there is a fairly large resistivity gap between observation spots MNS and KWR and that the boundary corresponds to the Hidaka metamorphic belt, that the metamorphic belt that is reflected as a conspicuous high-resistivity layer in the VLF-, ELF-MT slopes down toward the east and has a distribution as deep as 10km in the vicinity of observation point KWR, that this high-resistivity layer sandwiches a low-resistivity layer at a depth of 5-7km, and that on the east side of the metamorphic belt there is a medium-resistivity layer creeping under the belt from the east side toward the west side. 5 refs., 6 figs.

  2. Flow characteristic of Hijiori HDR reservoir from circulation test in 1991; Koon tantai Hijiori jikkenjo ni okeru senbu choryuso shiken (1991 nendo) kekka to ryudo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Shiga, T.; Hyodo, M.; Shinohara, N.; Takasugi, S. [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan)

    1996-05-01

    This paper reports one example of flow analyses on a circulation test carried out in fiscal 1991 at the Hijiori hot dry rock experimental field (Yamagata Prefecture). A fluid circulation model was proposed to simulate an HDR circulation system for a shallow reservoir (at a depth of about 1800 m) demonstrated in the circulation test by using an electric circuit network (which expresses continuity impedance in resistance and fluid storage in capacitance). Storage capacity of the reservoir was estimated by deriving time constant of the system from data of time-based change in reservoir pressure associated with transition phenomena during the circulation test. The storage capacity was estimated separately by dividing change of storage in the reservoir by change in the reservoir pressure. To derive the storage in the reservoir, a method to calculate non-recovered flows in the circulation test was utilized. The results of evaluating the reservoir capacity in the shallow reservoir using the above two independent methods were found substantially consistent. 3 refs., 6 figs., 1 tab.

  3. Succession of benthos and nutrient removal rate in the hydroponic culture system; Shokubutsu suiko saibaikei ni okeru konken seibutsu no henka to eiyoen no jokyo

    Energy Technology Data Exchange (ETDEWEB)

    Aizaki, M. [National Inst. for Environmental Studies, Tsukuba (Japan); Nakazato, H. [Biox Corp., Tokyo (Japan)

    1995-08-10

    Such nutrients as nitrogen and phosphorus discharged into lakes and rivers can cause organic contamination as a result of eutrophication in water areas if they are left as they are. However, they can be re-utilized as resources if they are utilized more effectively. This paper reports a hydroponic organism filtering method as a promising method of utilization thereof. It also explains transition in organism phase in rhizosphere and a water purification experiment. Such suspended matters as phytoplanktons in raw water are filtered and captured by roots of plants; such small animals as tendipedidae and physia live symbiotically in the rhizosphere; their excrements and nutrients are absorbed into and utilized by plants; and coexistence is made possible between diverse water-front environments including terrestrial systems and diverse living organisms. Cresson cultivation, observation on transition in the benthos composition, and a lake water purification experiment were carried out at the Kasumigaura Lake experimental facility. Various findings were acquired such that, in order to attain diverse coexistences including those with natural enemies and well-ventilated environments, a water channel of larger than a certain size is required. Results were also obtained that can be expected as an effective technique that may be used in public water areas. 3 refs., 4 figs.

  4. Study on the effect of measurement points upon reduced added mass matrix; Shukusho fuka shitsuryo matrix ni okeru kansokuten no eikyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Funaki, T.; Hayashi, S. [Osaka University, Osaka (Japan). Faculty of engineering

    1996-12-31

    It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. A parameter calculation was performed on node vibration in the vertical direction of a rotating elliptic body such as a ship to investigate the effect of an arranging method of the measurement points upon the result of the analysis. As a result, it is thought that equivalent interval arrangement of 21 measurement points would be sufficient in a lower order side mode of vibrations with less than four nodes. An analysis of calculations performed by arranging measurement points in experimental measurement points revealed that analysis accuracy would not increase even if the number of measurement points is increased if it is done so without considering rotation vector. An experiment was carried out with the number of measurement points increased to verify the above fact, with which the analysis was verified correct. Therefore, as has been forecasted in the previous report, the cause for the analysis accuracy deterioration in a high order mode may be estimated as the effect of the rotation vector. However, since it is not the situation that an analysis considering the rotation vector has been conducted, it cannot be concluded yet that the effect of the rotation vector is the sole cause. 4 refs., 14 figs., 7 tabs.

  5. Maneuvering response of slender ship with sinusoidal steering in shallow waters; Sensuiiki ni okeru saichosen no seigen soda ni yoru soju oto

    Energy Technology Data Exchange (ETDEWEB)

    Yasukawa, H. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1997-09-04

    In order to grasp memory effect of wake vortices on the maneuvering hydrodynamic characteristics and motions in shallow waters, this paper discusses maneuvering performance of ship advancing with sinusoidal steering. The unsteady slender body theory is used for analyzing the hydrodynamic characteristics acting the hull obliquely advancing or turning around, and hinge-flap model is employed for analyzing the rudder force characteristics. A method has been proposed by which variable components of bearing and transverse displacement of ship advancing with sinusoidal steering in shallow waters can be calculated. Differential coefficient of hull and rudder was calculated by varying the frequency. It was confirmed that the differential coefficient of hull agreed with the test results using cistern. Using this method, maneuvering response using hydrodynamic coefficient in the actual motion frequency was compared with that near the zero frequency. As a result, it was found that memory effect of wake vortices on the maneuvering response of ship can not be ignored in very shallow waters. 12 refs., 7 figs., 2 tabs.

  6. Detection of arcing ground fault location on a distribution network connected PV system; Hikarihatsuden renkei haidensen ni okeru koko chiryaku kukan no kenshutsuho

    Energy Technology Data Exchange (ETDEWEB)

    Sato, M.; Iwaya, K.; Morooka, Y. [Hachinohe Institute of Technology, Aomori (Japan)

    1996-10-27

    In the near future, it is supposed that a great number of small-scale distributed power sources, such as photovoltaic power generation for general houses, will be interconnected with the ungrounded neutral distribution system in Japan. When ground fault of commercial frequency once occurs, great damage is easily guessed. This paper discusses the effect of the ground fault on the ground phase current using a 6.6 kV high-voltage model system by considering the non-linear self-inductance in the line, and by considering the non-linear relation of arcing ground fault current frequency. In the present method, the remarkable difference of series resonance frequency determined by the inductance and earth capacity between the source side and load side is utilized for the detection of high-voltage arcing ground fault location. In this method, there are some cases in which the non-linear effect obtained by measuring the inductance of sound phase including the secondary winding of transformer can not be neglected. Especially, for the actual high-voltage system, it was shown that the frequency characteristics of transformer inductance for distribution should be theoretically derived in the frequency range between 2 kHz and 6 kHz. 2 refs., 5 figs., 1 tab.

  7. Experimental results of acetone hydrogenation on a heat exchanger type reactor for solar chemical heat pump; Solar chemical heat pump ni okeru acetone suisoka hanno netsu kaishu jikken

    Energy Technology Data Exchange (ETDEWEB)

    Takashima, T.; Doi, T.; Tanaka, T.; Ando, Y. [Electrotechnical Laboratory, Tsukuba (Japan); Miyahara, R.; Kamoshida, J. [Shibaura Institute of Technology, Tokyo (Japan)

    1996-10-27

    With the purpose of converting solar heat energy to industrial heat energy, an experiment of acetone hydrogenation was carried out using a heat exchanger type reactor that recovers heat generated by acetone hydrogenation, an exothermic reaction, and supplies it to an outside load. In the experiment, a pellet-like activated carbon-supported ruthenium catalyst was used for the acetone hydrogenation with hydrogen and acetone supplied to the catalyst layer at a space velocity of 400-1,200 or so. In the external pipe of the double-pipe type reactor, a heating medium oil was circulated in parallel with the flow of the reactant, with the heat of reaction recovered that was generated from the acetone hydrogenation. In this experiment, an 1wt%Ru/C catalyst and a 5wt%Ru/C catalyst were used so as to examine the effects of variation in the space velocity. As a result, from the viewpoint of recovering the heat of reaction, it was found desirable to increase the reaction speed by raising catalytic density and also to supply the reactant downstream inside the reaction pipe by increasing the space velocity. 1 ref., 6 figs., 1 tab.

  8. Results of photovoltaic power generation system operation in Tokyo Electric Power Company; Tokyo Denryoku ni okeru taiyoko hatsuden setsubi no unten jisseki ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Fukuda, H.; Itokawa, K. [Tokyo Electric Power Co. Inc., Tokyo (Japan)

    1996-10-27

    A report was made on the measurement of data and the results of the analysis at 14 sites of photovoltaic power generation facilities operated under system interconnection by Tokyo Electric Power Company. This type of system is provided in 40 sites as of the end of fiscal 1995, generating 479kw. The items measured were the generated electric energy at all 14 sites, and the quantity of solar radiation, outside air temperature, panel temperature, etc., at limited sites; and the capacity of each equipment, azimuth and inclination of the panel were also recorded simultaneously. Hourly values were used for the analysis. Five minute values were utilized, however, in the examination of the cause of lowered output and in the situation recognition of the influence of the shade or the change of weather. The utilization factor of the facilities was in the average 10.8% in fiscal 1994 and 10.7% in fiscal 1995. The factor decreased slightly unless the panel azimuth faced due south. The utilization factor at the panel inclination of 35 degrees and 45 degrees showed both 10.4% through the year making no difference. The system seemed to show no overwhelming possibilities in coping with electric power demand. The reason was that deviation existed for 2 hours or so in the peak and that reliability was low as basic power facilities. However, it was determined that the system be continuously examined in future. 9 figs., 1 tab.

  9. Technical trend and prospect for wafer cleaning on LSI manufacturing process; LSI seizo kotei ni okeru weha senjo gijutsu no saikin no doko totenbo

    Energy Technology Data Exchange (ETDEWEB)

    Hiratsuka, Y. [Dan Science Co. Ltd., Tokyo (Japan)

    1996-01-31

    Presently used cleaning process of silicone wafer is based on the modification of so called RCA method from the knowhow point of view, presented by W.Kern and others 25 years ago. On the other hand, with the progress of development of element for next generation, it was already clarified to be required on the process, demanded for high degree control of silicone surface. When considered the practical measure for this, there is a movement towards the establishment of new silicone wafer cleaning concept for new generation instead of making difficult process by precise RCA cleaning. One of the new proposed method is IMEC cleaning. Further, in Tohoku University, new cleaning process, alternative to RCA method is proposed, in which treatment of all chemicals is carried out at room temperature, types of chemicals used for cleaning are limited to minimum and also, concentration of these chemicals is kept as minimum as possible, amount of used superpure wafer is saved by effective recycling and reutilization of spent chemicals. With these tecnologies, there has appeared the sign for new development for cleaning technology. 36 refs., 28 figs., 6 tabs.

  10. Process of microbial degradation of petroleum hydrocarbons in the downstream of the Tamagawa river. Tamagawa karyuiki ni okeru sekiyukei tanka suiso no biseibutsu bunkai katei

    Energy Technology Data Exchange (ETDEWEB)

    Morito, M. (Sumitomo 3M Co., Kanagawa (Japan)); Okada, M.; Murakami, A. (Tokyo University of Agriculture and Technology, Tokyo (Japan). Faculty of Engineering)

    1990-12-10

    The process of biodegradation of petroleum hydrocarbons was investigated in the downstream of the Tamagawa river. Petroleum hydrocarbons, such as hexadecane, octylbenzene, and 1-methylnaphtalene were observed to be rapidly degraded by microorganisms in the water sampled from the surface of the river after a period of lag time. The longer lag time was observed in order of hexadecane

  11. Utilization of statistical table for waves in North-west Pacific Ocean and a long-term estimation on hull responses; Seihoku Taiheiyo haro tokeihyo no riyo to sentai oto choki yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Shinkai, A. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-10-01

    Designing a vessel to sail oceans for an extended period of time requires statistical estimation on different hull responses to waves. To meet the requirement, it is necessary to accurately identify hydrographic conditions (particularly waves) which are considered to be encountered by the vessel. This paper makes clear the statistical characteristics of the wave statistics table presented by Fang et al, and compares them with other processes for discussion. This statistics collection is based on data collected in China, Hong Kong and Japan, including those collected in the Sea of Japan, the Yellow Sea, the North Sea, the East China Sea and the South China Sea. It was found that these data provide results slightly lower than the long-term estimation values derived from data of the global wave statistics (GWS) prepared by Hogben et al. The cause for this was found attributable to the format of the statistical data, especially setting of wave height classes. However, since the data provided by Fang et al include items of detailed information on small sea areas near the Chinese coast lines, the data are thought to provide useful information source in investigating long-term hull response characteristics relative to spatial spread of the sea areas in the North-west Pacific Ocean. 15 refs., 5 figs., 2 tabs.

  12. FY 1995 report on verification of geothermal exploration technology. Development of fracture reservoir exploration technology (development of seismic exploration); 1995 nendo chinetsu tansa gijutsunado kensho chosa. Danretsugata choryuso tansaho kaihatsu (danseiha riyo tansaho kaihatsu) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This report provides the development of new exploration technology using elastic waves, such as reflection seismic survey, VSP, and seismic tomography, for precisely characterizing subsurface fractures in geothermal reservoirs. In order to investigate and improve the effective data acquisition and analysis methods for detecting a fault type of fractures, an experiment of a seismic tomography method was conducted using wells drilled in the Ogiri geothermal field, Aira-gun, Kagoshima Prefecture. An experiment of propagation characteristics of piezo type underground seismic source in the volcanic field was also conducted as a trend survey of underground seismic sources. The fracture type in the model field was systematically analyzed by measuring the core samples obtained in the demonstration test field through remanence measurement, fluid inclusion measurement, and zircon measurement using test equipment, and by analyzing results obtained from cores and results of seismic tomography obtained from the wells. Based on these results, the effectiveness and practical application of exploration methods using elastic waves were investigated. 80 refs., 250 figs., 49 tabs.

  13. WE-NET substask 3. Conceptual design of the total system (City-level energy estimation and assessment); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 3. Zentai system gainen sekkei (toshi kibo deno yosoku hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The effort of fiscal 1997 at isolating the best way to introduce a relatively small amount of hydrogen into urban fuel economy was carried over to fiscal 1998. In the research of fiscal 1998, comparison was made between Tokyo and London in connection with hydrogen introduction, and a transition scenario was proposed for introducing hydrogen into Tokyo. Models were built for Tokyo and London, and studied. The result of this study was different from that obtained in the previous study, and places the two cities under similar conditions. The difference is attributed to the rapid progress in the development of the fuel cell and to the resultant reduction in cost. It is inferred that, in consideration of the transportation situation, the introduction of pure hydrogen will be the most cost-effective for both cities at least for some time to come. According to the revised data, natural gas may be procured in Tokyo as in London but the size of supply available in Tokyo is fairly smaller than that in London. Several transition scenarios covering the period up to 2025 were subjected to discussion. (NEDO)

  14. Development of hydrothermal power generation plant. Development of binary cycle power generation plant (development of 10 MW-class plant); 1995 nendo nessui riyo hatsuden plant nado kaihatsu binary cycle hatsuden plant no kaihatsu. 10MW kyu plant no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    A 10 MW-class binary cycle power generation plant has been developed using a down hole pump (DHP) which exchanges the hydrothermal energy with secondary medium in the heat exchanger. For constructing the plant at Kuju-machi, Oita Prefecture, site preparation works, foundation of cooling tower, reconstruction of roads, and survey on environmental influences were conducted. To investigate installation and removal methods of DHP, a geothermal water pump-up system, current status of the binary cycle power generating system in the USA was surveyed. In this survey, a trailer mounting handling machine was inspected. Based on the survey results, a simple assembled, easy-installation type handling equipment was designed. In addition, the replacement work for motor connector joint of DHP and the strength of coil end were improved. Construction and method allowing reuse of the motor cable were considered by improving the cable and cable end portion. The air tight soundness of incoloy corrugate sheath was confirmed. Finally, a reproduction system for waste oil of DHP bearing oil was investigated. 106 figs., 52 tabs.

  15. Fiscal 1998 research report. Study on the feasibility of microorganism biotechnology for effective use of environmental pollutants. Pt. 2; 1998 nendochosa hokokusho. Kankyo osen busshitsu no shigenka no tame no biseibutsu bio technology riyo kanosei ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Study was made on the feasibility of microorganism biotechnology for effective use of environmental pollutants and unused resources. Microorganisms and microorganism enzymes for decomposing lignocellulose were viewed, and uses of hydrolysis products were summarized. Production of microorganisms applicable to fodder, composting, and production of energy sources (methane, hydrogen, ethanol) were studied. Use of vegetable fiber residues such as beer lees as fungus cultivation medium and conversion to valuable substances were also studied. Microorganisms treatment (MT) of wastes in fats and oils industry was summarized. Effective use of MT of protein waste from marine products was studied. MT of manures with the greatest impact on environment as livestock waste was summarized. The necessity of separate collection of domestic wastes, and composting and methane fermentation of kitchen garbage were reported. The feasibility of MT of plastic wastes, and decomposition of halogenated methane with high toxicity were also studied. (NEDO)

  16. Report on survey of international cooperation possibility on chemical CO2 fixation and utilization technology in FY 1997; 1997 nendo chosa hokokusho (kagakuteki CO2 koteika yuko riyo gijutsu ni kakawaru kokusai kyoryoku kanosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This survey focused on the end of the more promising companion and promoting the international cooperation on chemical CO2 fixation and utilization technology. As a result, the way of the carrying-forward of the international cooperation with more than one companion could be arranged beforehand. It led to getting an arrangement about a secrecy agreement respectively with Lurgi company and ABB company in Europe, and to providing a catalyst sample developed by RITE to implement an examination by the other party and to show related technical information. In addition, it concluded a cooperation agreement about a total system of the chemical CO2 fixation and utilization technology and methanol synthesis with ZSW. In Australia, negotiation about international cooperation with CSIRO which is a federal research organization and CRC (Cooperative Research Centre) for renewable energy has been started. The ideal circumstances are being ready for the chemical CO2 fixation project for which the international cooperation with the country where the natural energy is rich like Australia is essential when coming to practical use. To do alternating current with further high density in the following year it is desired to build a concrete study cooperation system. 1 fig., 4 tabs.

  17. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 3. Conceptual design of the total system; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 3. Zentai system gainen sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper describes the research result on the conceptual design of the total system for the WE-NET project in 1996. Basic conditions are as follows: solid polymer water electrolysis, hydrogen combustion turbine power generation, hydrogen transport/storage through ammonia medium, power generation scale of 1000-4000MW (2-5 yen/kWh), and transport distance of 5000-20000km between supply and consumption places. The system efficiency was estimated to be 68% and 23% at an ammonia arrival time and power sending end, respectively, and it was dependent on a transport distance, while no power generation scale. The power cost was estimated to be 7 yen/Mcal and 33 yen/kWh, respectively. The system efficiency at a sending end was lower by 15% and 2% than that of the liquid hydrogen and methanol system, while the power cost was higher by 0 and 8 yen/kWh, respectively. It was necessary for loss reduction of this ammonia system to develop a new high-efficiency ammonia synthesis process, and hydrogen separation (decomposition/refining) process. 80 figs., 52 tabs.

  18. Fiscal 1996 verification survey of geothermal exploration technology. Development of the fracture type reservoir exploration method (development of the elastic wave use exploration method); 1996 nendo chinetsu tansa gijutsu nado kensho chosa. Danretsugata choryuso tansaho kaihatsu (danseiha riyo tansaho kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of exploring accurately fracture groups greatly restricting the fluid flow of geothermal reservoirs, technical development was made for applying the elastic wave exploration technology such as the high precision reflection method, VSP, elastic wave tomography to the geothermal exploration. The Okiri area, Kagoshima prefecture was selected as a demonstrative field of a typical type where the steep and predominant fracture rules the geothermal reservoir, and experiments were conducted using the high precision reflection method and VSP. Fracture models were made, and the analysis results were studied by a survey using the array CSMT/MT method and by a comparison with existing data. Reformation of the underground receiving system used for VSP and elastic tomography is made for improvement of its viability, and was applied to the VSP experiment. The treatment/analysis system of the core analyzer was improved, and cores of the demonstrative field were analyzed/measured. Further, the exploration results, core analysis results and existing data were synthetically analyzed, and fracture models of the demonstrative field were constructed. Also, effectiveness and viability of the elastic wave use exploration method were studied. 90 refs., 418 figs., 24 tabs.

  19. Research cooperation project in fiscal 1998. General report on research cooperation related to mine waste water treatment technology by utilizing biotechnology; 1998 nendo kenkyu kyoryoku jigyo. Bio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku sokatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper describes cooperative development of bio-treatment technology for mine waste water generated by operating mines in China. Certain types of bacteria have capability to oxidize ferrous iron in the waste water into ferric iron ions. The bacteria cause ferric iron oxides in low pH regions to get deposited, and can remove them from sedimentation by using cheap calcium carbonate as a neutralizer. Volumetric reduction in waste sediments may also be achieved during removing heavy metals in a pretreatment process. Great advance may be expected in taking actions to prevent water quality contamination. This paper summarizes activities taken in fiscal 1998. Eight site surveys in total were carried out using 47 persons in total. Major activities included operation study guidance of a pilot plant, and surveys for measures on heavy metal generation sources in Wushan Mine. In addition, site surveys were performed at Dexing Mine and Yinshan Zinc Mine. Subsequently from fiscal 1997, a bench scale testing equipment used in Japan and consumables were transported to China. The operation study data on the pilot plant were put into order and analyzed. Concept design was also made on a waste water treatment facility for Wushan Mine. (NEDO)

  20. Synthetic studies on axial chiral biaryls and functional materials utilizing arene-metal complexes; aren kinzokusakutai no tokusei wo riyo shita jikufusai biariru, oyobi shinki kinosei zairyo no gosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Uemura, Motokazu [Osaka Prefecture University, Osaka (Japan). Faculty of Integrated Arts and Sceinces

    1999-12-16

    Axially chiral biaryls compounds are of importance not only as chiral ligands for asymmetric reactions but also as biologically active natural products, e. g., korupensamine, michellamine and vancomycin. (Arene) chromium complex exists in two enantiomeric forms based on a planar chirality. Axially chiral biaryls were stereoselectively prepared by palladium(0)-catalyzed cross-coupling of (aryl halide)Cr(CO){sub 3} complexes with arylboronic acids. This method was applied for the total synthesis of antimaralial agent korupensamine A, naphthyltetrahydro-isoquinoline alkaloid. Furthermore, chiral 1,2-diols and diamines are important compounds for asymmetric reactions. These enantionerically pure 1,2-diols and 1,2-diamines were stereoselectively prepared by pinacol coupling of planar chiral chromium complexes of benzaldehydes and benzaldimines with samarium iodide. Moreover, non-biaryl axial compounds, N,N-dialkyl 2,6-disubstituted benzamides were synthesized in enantiomerically pure form utilizing planar chiral arene chromium complex. (author)

  1. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 4. Development of hydrogen production technology; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 4. Suiso seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper describes development of hydrogen production technology as a part of the WE-NET project. For the solid polymer water electrolysis method higher in efficiency and lower in cost than the previous methods, 5 companies have developed element technologies for improving electrolysis cells and synthesis technologies of hot solid polymer electrolyte based on each proper catalyst electrode production method. In fiscal 1996, the initial study on large-scale systems by middle laboratory cells was made as well as improvement of electrolysis performance by small laboratory cells and endurance tests. Among the previous methods such as a hot press method (bonding of an ion exchange membrane to an electrode), an electroless plating method (preparation of porous surface onto a membrane electrode assembly), a zero gap method (preparation of high-efficiency high-current density cells), and a sintered porous electrode method (carrying of the mixture of catalytic powder and ion exchange resin-dissipated solution onto sintered metallic porous electrode surface), the former two methods were adopted for development of bench-scale cells as effective promising methods. 192 refs., 183 figs., 108 tabs.

  2. Fiscal 1996 verification survey of geothermal exploration technology. Development of the fracture type reservoir exploration method (development of the elastic wave use exploration method); 1996 nendo chinetsu tansa gijutsu nado kensho chosa. Danretsugata choryuso tansaho kaihatsu (danseiha riyo tansaho kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of exploring accurately fracture groups greatly restricting the fluid flow of geothermal reservoirs, technical development was made for applying the elastic wave exploration technology such as the high precision reflection method, VSP, elastic wave tomography to the geothermal exploration. The Okiri area, Kagoshima prefecture was selected as a demonstrative field of a typical type where the steep and predominant fracture rules the geothermal reservoir, and experiments were conducted using the high precision reflection method and VSP. Fracture models were made, and the analysis results were studied by a survey using the array CSMT/MT method and by a comparison with existing data. Reformation of the underground receiving system used for VSP and elastic tomography is made for improvement of its viability, and was applied to the VSP experiment. The treatment/analysis system of the core analyzer was improved, and cores of the demonstrative field were analyzed/measured. Further, the exploration results, core analysis results and existing data were synthetically analyzed, and fracture models of the demonstrative field were constructed. Also, effectiveness and viability of the elastic wave use exploration method were studied. 90 refs., 418 figs., 24 tabs.

  3. Research cooperation report for fiscal 1997 on the environment-friendly system for effectively utilizing water resources; 1997 nendo kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku itaku gyomu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This effort exerted in cooperation with the Philippines aims to solve problems related to water resources such as stable supply and pollution of water through developing a waste water treatment/water reuse system which is easy to operate and maintain, and low in price. The ultimate goal includes (1) the construction of a waste water treatment/water reuse system comprising an anaerobic reaction tank and activated charcoal absorption tower, easy to operate and maintain, and low in price, (2) the employment of goods procurable in the Philippines, the goods including carriers for use in the anaerobic reaction tank, microbes for use in both aerobic and anaerobic reaction tanks, and activated charcoal for use in waste water reutilization, and (3) the establishment of optimum operating conditions for the waste water treatment/water reuse system by use of a pilot plant and the transfer of operating and managing techniques to the Filipino counterpart. In this fiscal year, investigations are conducted to disclose the actualities of waste water treatment and water consumption by primary industries in the vicinity of Laguna de Bay, and the waste water to be the object of study and the place of pilot plant installation have been selected. Also conducted are investigations into the carrier, microbe, activated charcoal, etc., for use in the anaerobic reaction tank. (NEDO)

  4. FY1998 report on a survey related to joint utilization of welfare device development data using an international network; 1998 nendo kokusai network ni yoru fukushi kiki kaihatsu data no kyodo riyo ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A survey was made in relation with joint utilization of welfare device development data using an international network. Developing welfare devices requires data from ergonomic and medical systems, while the cope of the objects is wide, and the kinds are various. For proliferation of welfare devices, system compatibility evaluation including that on using environment is important, including living environments that are different by countries. The present survey has identified how data for aged, handicapped and help-needing persons are accumulated and utilized in research organizations in America and Europe for both of the ergonomic and medical areas. The survey also investigated major academic societies in overseas countries, and collected database and academic network information that support the advanced research and development. At the same time, investigations were also made on organizations and corporations who are moving forward the efficient data utilization. Welfare device and service information providing systems in Japan were investigated to compare them with the trends in other countries. Conceptions and methods were compiled to utilize data internationally and jointly. Database models for device development were considered, and a proposal was made on structuring a research and development supporting database, and the operation method thereof. (NEDO)

  5. Survey report of FY 1997 on the feasibility of microbial biotechnology for reuse of environmental pollutants; 1997 nendo chosa hokokusho (kankyo osen busshitsu no shigenka no tame no biseibutsu bio technology no riyo kanosei chi kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    An investigation was conducted with the aim of elucidating the foundations for effective utilization of environmental pollutants or unused resources which are likely to be causal substances of environmental pollutants, as resources, using biotechnology. Composting of agricultural waste, production of microbial mycelium proteins and microbial fermentation materials were suggested as main examples of effective utilization of unused resources by microorganisms. Selection of active microorganisms in the livestock waste, clarification of the mechanism of action and the establishment of treatment conditions are essential to new developments in this field. In the field of marine products industry, it was pointed out that the recycling of waste using microorganisms and enzyme treatment is the most promising approach to the effective utilization of resources. In the field of food industry, applications as the culture media for mushrooms, for enzyme production and for the production of physiologically active materials as well as fuel were clarified. Was also pointed out the significance of studies on the microorganisms and enzymes in resources containing cellulose, hemicellulose and lignin, and the waste from these resources, lignocellulose. Were also proposed the composting of household waste, methane fermentation, and fermentative production of organic acid and hydrogen from waste. Possibility and significance of fermentative production of organic acid from sewage sludge were suggested. 314 refs., 46 figs., 33 tabs.

  6. Study on electrical monitoring of fill-up improvement. Utilization of resistivity data for soil compaction management; Hiteiko mitsudo kanri ni kansuru kisoteki kenkyu. Moritsuchi seko kanri eno hiteiko yuko riyo

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, N.; Hiramatsu, W. [Dai Nippon Construction, Gifu (Japan); Sugano, T. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1996-10-01

    At present, measurement of wet density and water content by radio isotope (RI method) is used for filling management. It is supposed for filling in road construction that putting-out thickness of banking material reaches nearly 1m in the future rapid construction, however, use of RI method is difficult because of inserting and installing of a radiation source rod, large measuring apparatus, and the legal regulation on radioactivity intensity. Application of resistivity measurement was thus considered. Since resistivity has the same parameter as compaction curve, and monotonously decreases with an increase in water content by volume, it is applicable as construction management index. The management reference of resistivity (Rm) is set by plotting of a compaction curve and corresponding resistivity curve, determination of the reference resistivity (Ro) corresponding to a maximum dry density and optimum water content ratio, and setting of the allowance to Ro according to soil or application. It was clarified that Rm is applicable as set for every filling material. 1 ref., 10 figs., 2 tabs.

  7. Recent trends in computer application in industrial fields and how to apply its technology to oil drilling field. Tasangyo deno computer riyo no genjo to kussaku sagyo eno oyo no kanosei

    Energy Technology Data Exchange (ETDEWEB)

    Matsuo, Keisuke

    1989-09-01

    This report looks back on the 30 year history of computers and plant automation, and suggests the way to apply computers to the field of drilling. Recent trends are distribution of controls and contrarious integration. This integration is hierarchical integration to the upper level by integrating process instrumentation, electricity and computers. With the development of communication technologies, on-line, real time, and multi-task operations became possible. Furthermore, control technologies including the optimization by simulation were advanced, and breakdown diagnosis and operation support by artificial intelligence technologies were put to practical use. Possible application examples of these technologies to drilling works are a microcomputer which operates measurement controlling equipments according to the information on the drilling rig from mud loggers, a microcomputer which controls handling of equipments, and configuration of LAN including communication stations which can transmit inquiries into the progress of drilling or the way to handle troubles. 12 figs., 3 tabs.

  8. Study on synergistic effects of urban mixed-uses developments. Research into the complex uses of offices, shopping centers and hotels; Toshi kaihatsu no yoto fukugo ni yoru sojo koka no kenkyu. Office shogyo shisetsu hotel no fukugo riyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    Mori, N.; Ito, T. [Kajima Corp., Tokyo (Japan)

    1995-12-20

    Complex facilities consisting of offices, shopping centers and hotels were investigated to discuss synergistic effects of compounding the different uses. The investigations included an investigation on passing behaviors and traffic amount among facilities of different uses around and inside the complex facilities, a questionnaire survey on visitors for their composite utilization, impression and evaluation of the facilities and another questionnaire survey on office workers for their composite utilization of the facilities inside and outside the complex facilities. The result of analyses using simple calculations and multi-dimensional measure methods revealed the following points: improvement on images of the whole facility as a result of strong customer collecting power of the commercial facilities, support effects on hotels and malls, roles and utilization patterns of commercial facilities, hotels and various facilities existing in peripheral areas that function to support office works, and roles of open squares and malls that coordinate and integrate the facilities of different uses and promote passing activities. It was also observed that resident time is extended as a result of composite utilization, and that the shift in peak time of the number of people utilizing the commercial-based and office-based facilities results in more efficient utilization of parking lots and restaurants. 1 ref., 9 figs., 2 tabs.

  9. Analysis on recreational development and deforestation due to accessibility improvement in the suburban areas; Kotsu kaizen ni kiinshita kanko chiiki no shizenteki tochi riyo no henka ni kansuru bunseki

    Energy Technology Data Exchange (ETDEWEB)

    Doi, K. [Tokyo Institute of Technology, Tokyo (Japan); Okamoto, N. [Japan Transport Economics Research Center, Tokyo (Japan); Murata, A. [Housing and Urban Development Corp., Tokyo (Japan)

    1997-07-20

    In the suburban areas, the abundance of natural resources is essential for recreational activities. However, it is often observed that the increase in recreational travelers causes the degradation of natural environmental quality. The purpose of this study is to analyze the impact of transport improvement on development and the consequent decrease of natural green areas in suburban areas. A method of LISREL is adopted for identifying the contribution of green conservation to recreational attractiveness and the causalities among degradation of green conservation and accessibility improvement. A simultaneous equations system of recreational travel demand and developers` strategy is modeled and adopted for assessing the impact of accessibility improvement on the depletion of green areas. 14 refs., 15 figs., 6 tabs.

  10. Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of the high efficiency waste-fired power generation system using CSD; Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (CSD riyo) jigyoka FS chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the current treatment of disused cars, valuable materials are recovered after scrapping them, and residual car shredder dust (CSD) is reclaimed. The load of land reclamation can be reduced by decreasing its volume and weight through incineration of combustibles in the CSD. Thermal energy obtained during the incineration can be converted into electric power. CSD-fired power generation plant has been planned, by which the obtained power is sold to electric power companies. It was assumed that the power generation plant is constructed at a certain city of Ibaraki Prefecture. Two cases of plant scales, i.e., 200 t/d and 400 t/d, were investigated by considering the collecting quantity of CSD fuel and the area of sites. The CSD fuel with 4,500 kcal/kg of lower calorific value contains rather high contents of chlorine and sulfur, which are around 3% and 1.6%, respectively. Therefore, the system should have measures, such as the exhaust gas treatment, dioxin treatment, and prevention of corrosion for high efficiency. It was concluded that about 300 t/d scale plant provides a feasibility. 27 refs., 21 tabs.

  11. Report for fiscal 1998. Joint research of environment-friendly system for effectively utilizing water resources; 1998 nendo hokokusho. Kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The research is conducted in cooperation with Industrial Technology Development Institute of the Philippines, and aims to solve water related problems such as unstable water supply and water quality pollution though developing a waste water treatment and recycling system which is easy to operate and maintain, low in cost, and usable in the Philippines. Fiscal 1998 is the second year of the project. Statistics are studied about the load that each industrial branch imposes on water for its pollution, and it is found that food manufacturers, paper pulp mills, and fiber dyeing plants are heavily responsible for water pollution. A method consisting of single-tower UASB anaerobic treatment and activated sludge treatment is applied as a water treatment process to Ram Food Products Corporation, and its optimization is studied. A removal rate 60% is achieved after a 12-hour treatment period at a COD (chemical oxygen demand) rate of 8g/liter/day. A method consisting of coagulating sedimentation and activated sludge treatment is applied to the waste water from a Solid Mill Corporation dyeing plant, when it is found that the water after ultimate treatment is almost colorless and that COD is 76mg/liter and BOD (biological oxygen demand) 13mg/liter, and these suggest that the waste water is recyclable. Since it is low in COD removing rate, the application of anaerobic treatment to high-concentration water after washing is not appropriate. (NEDO)

  12. 1998 research cooperation project. Research cooperation on environment-compatible type water resource effective-utilization system; 1998 nendo kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of securing water stably and preventing water pollution in the Philippines, R and D were carried out on a wastewater treatment and water reclamation and reuse system which is easy to operate and maintain and low in cost through the research cooperation between the Philippine Industrial Technology Development Institute and Japan. According to the survey result of statistical data concerning water pollution load structure by industrial wastewater classified by the industry in the Philippines, enumerated are the food manufacturing industry, paper pulp manufacturing industry, and the textile dyeing industry as those greatly affecting water pollution in BOD exhaust and wastewater, etc. Consequently, with Ram Food Product Co. of vegetable processing and Solid Mill Co., of textile dyeing as plants to be studied, a wastewater treatment test was performed in a laboratory scale. From the result of the test, the pilot plant was basically designed to have 'anaerobic + aerobic treatment + tertiary treatment' for the treatment process, with an one-tank type UASB method used as the anaerobic treatment, with a sand filtration + activated charcoal treatment as the tertiary treatment, and with the cost effectiveness for water reuse set to be examined. (NEDO)

  13. FY 1998 result report. Research/development on the energy overall development/utilization technology of gas hydrate resource; 1998 nendo seika hokokusho. Gas haidoreto shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This study is aimed at studying for survey of gas hydrate (GH) deposit required for GH resource development and gathering of it, and further at studying for industrial utilization technology development of GH which is different in formation condition depending on kind of gas with which it reacts. The results of FY 1998 are as follows. In the study of the situation of existence of gas hydrate in the tundra, the sedimentary environment of the tundra where natural gas hydrate exists was simulated in laboratory to measure thermal conductivity of the sediments including GH. In this fiscal year, design/fabrication/calibration were conducted of the GH synthesizer and thermal analyzer. In the study of GH gathering technology in the tundra, a technology is discussed for recovering gas from GH layer and at the same time substituting CO2 hydrate for GH by blowing CO2 into the geologic layer. In FY 1998, formation/dissociation behaviors were first studied of methane/CO2 mixture hydrate. For the overall energy development of GH resource and promotion of R and D of the utilization technology, studies were made on physical properties of GH and development of the usage. (NEDO)

  14. Fiscal 1997 report on the cooperative research on the preservation and sustainable utilization of biological diversification; Seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku (1997 nendo hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Cooperative researches were conducted between Japan and Thailand, Indonesia and Malaysia for the purpose of the technology development to make developing countries themselves preserve bioresources existing in tropical forests and use those sustainably. The research subjects for Thailand are a strategical study on eating of the primates, improvement of a microorganism culture collection system, preservation of biological diversification using an artificial ecosystem, bioresource utilization, etc. The subjects for Indonesia are a study of a microorganism culture collection system, study of plant preservation technology, study of microorganism utilization technology, study of plant utilization technology, promotion of the founding of the Indonesia tropical bioresource information center, etc. The subjects for Malaysia are biological diversification database and gene bank, assessment/monitoring of the ocean ecosystem, assessment and inventory of the ecosystem using hi-tech technology, search/separation of bioactive substances originated from microorganism/plant, etc. 26 refs., 24 figs., 81 tabs.

  15. Simulation study on reduction of peak power demand and energy consumption in residential houses with solar thermal and PV systems; Taiyo energy riyo jutaku no fuka heijunka oyobi energy sakugen koka no simulation ni yoru kento

    Energy Technology Data Exchange (ETDEWEB)

    Endo, T. [Yokohama City Office, Yokohama (Japan); Udagawa, M. [Kogakuin Univ., Tokyo (Japan). Faculty of Engineering

    1995-11-20

    In this study, taking the all factors involved in the energy consumption in residential houses as subjects, the effectiveness of the solar PV system and solar thermal utilizing system in residential houses has been studied by simulating a model residential house considering the improvement of the residual environment in the future. Therefore, a model residual house is assumed, 18 kinds of combinations of construction style, cooling and heating type and solar energy utilizing form are assumed and year round simulation is carried out. The conclusions obtained by the simulation are as follows. The energy consumption in residential houses may decrease greatly by using a solar hot water supplying system. If combined with a solar PV system, the energy consumption in one year is about 8.7 to 9.7 MWh. The combined use of a solar thermal utilizing system and a PV system is more effective to reduce the second-time energy in comparison with the PV system only. 36% of the space heating energy consumption may be decreased by using the solar space heating system, but the decrease effect of the energy consumption of the solar space heating system is smaller than the solar hot water supplying system. 12 refs., 26 figs., 3 tabs.

  16. Trial to active SWD using artificial energy source. Use of monochromatic source wavelet; Jinko shingen wo mochiita SWD eno kokoromi. Tan`itsu shuhasu no shingen hakei no riyo

    Energy Technology Data Exchange (ETDEWEB)

    Tsuru, T.; Kozawa, T. [Japan National Oil Corp., Tokyo (Japan); Taniguchi, R. [Mitsubishi Electric Corp., Tokyo (Japan); Matsuhashi, K. [Matsuhashi Techno Research, Hiroshima (Japan); Nishikawa, N. [Fuji Research Institute Corp., Tokyo (Japan)

    1998-04-01

    Seismic while drilling (SWD) is an accurate and safe method for drilling, by which real-time information regarding bit location and bedding boundary below the bit can be predicted by using elastic wave during drilling of rocks in a borehole. However, the signal level is rather low compared with the noise generated from the rig during drilling, resulting in the deteriorated data quality. Since the impact resiliency is small in soft beds, it is difficult to obtain good data due to the small energy of seismic wave propagating along drilling pipe. In order to overcome these problems, active SWD method using artificial seismic source has been developed. This method provides stable low-frequency seismic wave with large energy by the artificial seismic source adopting spring-mass system resonance method. Although the seismic source wave is monochromatic, the direct wave can be sufficiently analyzed and the bit location can be detected on the time profile of seismic prospecting. Protection of borehole damage during dropping of the equipment, energy propagation efficiency in the beds, and analysis of reflected wave are future problems. 11 refs., 6 figs., 4 tabs.

  17. Fiscal 1998 research report on information structuring technology for advanced use of NEDO research reports; 1998 nendo NEDO seika hokokusho nado no kodo riyo ni hitsuyona joho kozoka gijutsu no chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research was made on electronic NEDO research reports corresponding to the recent extending trend of Internet. The logical structure and electronic format of NEDO research reports as document were first studied considering document disclosure and reuse of technical information. HTML as electronic format for Internet is unfortunately insufficient to describe the logical structure of NEDO research reports because of HTML's restricted description. Thus, XML which is being watched because of its possible definition of original tags was studied in place of HTML. As a result, because at present preparation of standards on XML and a compatibility for implementation of standards are insufficient, it was concluded that construction of the electronic document system for NEDO research reports is still too early. However, since adoption of XML as document format is important from the viewpoint of a property succession on Internet, preparation of the XML format file of NEDO research reports is essential. (NEDO)

  18. Multiobjective optimization of maintenance planning for existing bridges by using Bridge Management System (BMS); Bridge Management System (BMS) wo riyo shita kizon kyoryo no saiteki iji kanri keikaku no sakutei

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, A.; Nakamura, H. [Yamagata Univ. (Japan). Faculty of Science] Kawamura, K. [Yamaguchi Univ., Yamaguchi (Japan). Graduate School

    1998-03-20

    The authors have been developing the Bridge Management System. As one of main functions of this system, a new function is added which affords an optimum maintenance plan (repair and reinforcing) with consideration of the cost and quality of bridge members for each subject bridge. {epsilon}-Limiting method is used for multiobjective optimization and the genetic algorithm to enable parallel search of the solution is adopted for the search of the optimum solution. In this system, various data of the bridge and inspection data are processed in the deterioration diagnosis function and its output is processed in the deterioration prediction function. From the result, the optimum maintenance plan is produced in the maintenance plan optimization function. The maintenance measure (repair and reinforcing) and the effects of the maintenance measure on the predicted deterioration curve should be determined beforehand for the optimization. An application of this system to an existing bridge verifies the efficacy of the system. 18 refs., 8 figs., 9 tabs.

  19. Report on a survey in fiscal 1998 for petroleum substituting energy development and utilization in the Pacific Ocean region; 1998 nendo Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A survey was carried out to make available the information base that can collect, put into order and provide quickly and accurately the energy related information based on global environment problems in the Pacific Ocean region. Fiscal 1998 has performed a substituting energy demand and supply analysis in the Pacific Ocean region by adding the 1996 data, in addition to collection of the normal energy data. For the purpose of analyzing the petroleum substituting energy demand and supply in the Pacific Ocean region, data were collected from 17 countries for fiscal 1997 and the quarterly data for 1998. Retroactive data collection was also continued. The growth rate of primary energy supply in the Pacific Ocean region is 1.8% in average in the 1980's, and 3.8% in the 1990's. In contrast, the growth rate of petroleum substituting energies is 6.4% in the 80's and 6.2% in the former half of the 90's, being far higher than the growth rate of the primary energy supply. The share of the petroleum substituting energies accounting for in the primary energy supply has increased from 6.7% in 1980 to 12.1% in 1996. As the breakdown, nuclear power accounts for overwhelmingly large, followed by geothermal energy and new energies. (NEDO)

  20. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 2. Research study on promotion of international cooperation; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 2. Kokusai kyoryoku suishin no tame no chosa kento

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper describes the research result on promotion of international cooperation in the WE-NET project in fiscal 1996. The WE-NET project aims at development of the total system for hydrogen production, transport, storage and utilization, and construction of the earth-friendly innovative global clean energy network integrating elemental technologies. Since the standpoint is different between latent resource supplying countries and technology supplying countries, the WE-NET project should be constantly promoted under international understanding and cooperation. The committee distributed the annual summary report prepared by NEDO to overseas organizations, and made positive PR activities in the 11th World Conference and others. The committee made the evaluation on the improvement effect of air pollution by introducing a hydrogen vehicle in combination with Stanford University, and preparation of PR video tapes for hydrogen energy. Preliminary arrangement of Internet home pages, establishment of a long-term vision for international cooperation, and proposal toward the practical WE-NET are also made. 9 figs., 13 tabs.

  1. Fiscal 2000 survey report. Survey report on development and utilization of alternative energies for oil in Pacific region; 2000 nendo Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A survey was conducted, with environmental matters taken into consideration, for building an information gathering infrastructure for the countries in the Pacific region, capable of promptly and accurately collecting and offering energy related information. Conducted in this fiscal year were regular data gathering, review of oil supply and demand and alternative energy supply and demand in the Pacific region, on-site survey of alternative energy development and utilization in Vietnam, quarterly analyses of trend of energy demand, and the like. The supply of primary energy in the Pacific region increased by 2.3% per year in the period 1980 through 1998. The rate of increase was the lowest with oil, and the highest with hydroelectricity, atomic power, and recoverable energies such as geothermal energy. The Vietnamese Government is promoting its efforts to develop power sources by use of recoverable energies for farm village electrification. Efforts are being earnestly exerted to develop its rich natural gas resources and it is expected that there will be a remarkable achievement in the use of alternative energies due to an increase in natural gas consumption. In the field of data collection, various data were registered with the database. (NEDO)

  2. Would natural gas utilization continue expanding. ; Assurance of supply to respond to demand increase and Japan's choice. Tennen gas riyo wa kakudai wo tsuzukeruka. ; Juyo zodai ni taiosuru kyokyu no kakuho to Nippon no sentaku

    Energy Technology Data Exchange (ETDEWEB)

    1993-06-06

    This paper summarizes future prospects on natural gas. The world's natural gas consumption during the fiscal year 1991 amounted to 2 trillion 100 billion m[sup 3],acounting for 23% of the primary energy consumption. Japan has consumed 52.7 billion m[sup 3] (ranked sixth in the world) in the same year. Consumption in Japan, Korea, Taiwan, North America and Europe was 1 trillion 100 billion m[sup 3], 20% being depended on out-of-the-area sources. In 2010, difference between the demand (1 trillion 500 billion to 1 trillion 600 billion m[sup 3]) and in-the-area production would expand, causing a shortage of 10 billion to 50 billion m[sup 3]. As new supply sources, 18 projects are in progress in 11 countries, each with problems, however. A consideration on the situation according to confirmed reserve amount reveals that the demand-supply gap in 2010 may not be filled up. Europe is under a strict situation requiring countermeasures. In the Far East areas, no gap is estimated to occur. LNG price will rise as a result of double hull vessel regulations and increase in distance from supply sources. In order to deal with the LNG demand increase, Japan would have to depend upon supply from the former Soviet Union and Middle East areas. 7 figs., 4 tabs.

  3. Proposal of an air-conditioning system using underground heat exchanger as a countermeasure for the heat island problem and its evaluation; Chika hitoshinku reibo wo riyo shita atarashii hitoairando taisaku no teian to sono kanosei no kento

    Energy Technology Data Exchange (ETDEWEB)

    Genchi, Y.; Kasumi, H.; Saruta, H.; Wei, Xin-Gu.; Komiyama, H. [Tokyo Univ. (Japan). Graduate School

    1997-09-05

    These recent years, big cities like capital city as compared to suburbs are facing city heat island problem causing severe temperature increase. For example, there are measured results that the temperature around Nihonbashi, Tokyo, which has the highest density of energy consumption, was 4degC higher than that of coastal area having lower energy consumption density. The speedy increase of power consumption in summer due to massive cooling load is one of the main problem of heat island. The worse cycle of temperature increase is caused by the increase of heat liberated from cooler together with the addition of heat liberated from vehicles and so forth. Main measures for heat island carried out so far has been studied from the point of view of save energy technology for each such as efficiency improvement of heat pump cooling machine and combustion improvement of vehicles. In future, necessity of save energy measures from macro point of view that reduces the heat liberated in the whole city is cited. 24 refs., 7 figs., 3 tabs.

  4. Synthesis of inorganic mesopore materials and their application to control chemical reactions; Muki meso kukan zairyo no gosei to kagaku hannoba to shite no riyo gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ohashi, F.; Tomura, S.; Maeda, M.; Inukai, K.; Suzuki, M.; Okazaki, M.; Konishi, Y.; Toriyama, K. [National Industrial Research Institute of Nagoya,Nagoya (Japan)

    2000-10-25

    Materials enabling 'intelligent humidity control' were synthesized by using fumed silica, tetraethylorthotitanate, and a surfactant (alkyltrimethylammonium bromides (C{sub n}H{sub 2n+1}(CH{sub 3}){sub 3}N{sup +} (center dot) Br{sup -}, n=10 - 16) as a liquid-crystal template) under a hydrothermal condition. A homogeneous hexagonal structure of SiO{sub 2}-TiO{sub 2} was confirmed from X-ray diffraction analysis and TEM observation. These products had a high BET surface area of 540-863m{sup 2}/g and auniform pore diameter of 1.5-3nm, both of which were controlled by varyingthe size of the organic template molecule. A sharp increase in water adsorption was observed when the relative pressure (P/Po) increased in the range 0.4 - 0.6. Over this region, the weight % of water came in the range 20 - 50mass%. The water vapor adsorption isotherm was classified as type V in the IUPAC notation, which is characteristic of an unusually large hysteresis. This large hysteresis can be explained from the fact that the contact angle depends on whether water is being adsorbed or desorbed. High durability in their humidity-control ability was confirmed from repeated observation of the isotherm. As a characteristic of the chemical structure upon titanium incorporation, a wider distributionof the Si-O-Si angles in the SiO{sub 4} tetrahedra was indicated from the broad Q{sup 4} {sup 29}Si-MAS/NMR spectra with a small peak shift. To clarify the formation process of these mesoporous materials in the template-synthesis, we accumulated the basic parameters of micelles from the product-yield-detected ESR observations. In addition, as a model of the chemical reaction in the mesoporous material, we observed the reaction dynamics in a spherical micelle with the same technique Based on these preliminary experiments we designed a column reactor packed with a me soporous material to control the liquid phase reaction. (author)

  5. Study of an optimization of regeneration for an absorbent used in the solar desiccant cooling system; Taiyonetsu riyo desiccant reibo ni mochiirareru kyushuzai saisei tokusei no saitekika ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Y. [Osaka Institute of Technology, Osaka (Japan)

    1997-11-25

    A desiccant cooling system uses concentrated aqueous solution of an absorbent to reduce humidity, hence the resultant absorbent solution becomes dilute. Regeneration of the dilute solution uses solar heat, where the regeneration characteristics are affected by solution temperature, vapor pressure, water content, air-liquid flow rate, and other factors. Therefore, mutual relationship among these different factors were investigated, and an optimum operating condition was discussed. The regeneration characteristics of the absorbent is strongly affected by temperature of triethylene glycol (TEG). This is because vapor pressure, Ps, in the TEG aqueous solution increases as the TEG temperature rises. This means that preheating the solution is effective in regenerating the absorbent. As the regeneration progresses, the water content, Ww, decreases, and the regeneration rate decreases. This is because of reduction in the Ps in association with decrease in the Ww of the TEG. This suggests that it is important in the absorbent regeneration to reduce flow rate of the TEG aqueous solution as low as possible. Raised air temperature reduces difference in vapor partial pressure between the TEG and the air, resulting in reduced regeneration rate. 5 refs., 9 figs.

  6. Annual cycle solar energy utilization with seasonal storage. Part 8. Study on periodic steady state of the annual cycle energy system at a practical operation; Kisetsukan chikunetsu ni yoru nenkan cycle taiyo energy riyo system ni kansuru kenkyu. 8

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, H.; Okumiya, M. [Nagoya University, Nagoya (Japan)

    1997-11-25

    A study was made of the periodic steady state of the annual cycle solar energy system with seasonal heat storage at a practical operation. Cold heat in winter and warm heat in summer are stored in the seasonal storage tank, and these are each used in shift until when demand for cold/warm heat appears. Moreover, gap in quantity of cold/warm heat going in/out of the heat storage tank during a year is filled by natural energy such as solar energy, so that the system can be operated in annual cycles. Studies were conducted of the periodic unsteady term and the problem on lowering of performance during the term such as the periodic unsteady term of water temperature inside the seasonal heat storage tank and temperature of the soil around the storage tank, and the level of lowering of performance during the term, necessity of additional operation/control at the start of operation and aged deterioration of the system. Within the assumption, even if starting operation in any time of the year, the system could show the performance almost expected from the first operation year with no additional system operation and control required only at the start of operation. It is thought that the heat source selection control of heat pump largely contributes to this. 4 refs., 5 figs., 3 tabs.

  7. Improvement of a manageability of biological nitrogen and phosphorus removal plant using a wastewater treatment process simulator; Gesui shori purosesu shimyureta no riyo ni yoru seibutsuteki chisso/rin jokyo puranto no kanrisei no kojo

    Energy Technology Data Exchange (ETDEWEB)

    Kurata, G. [Toyohashi Univ. of Technology, Aichi (Japan). Faculty of Engineering; Tsumura, K. [Kyoto Univ., Kyoto (Japan). Graduate School; Yamamoto, Y. [Osaka Prefectural Inst. of Public Health, Osaka (Japan)

    1997-02-10

    In this paper, a method for executing a stable management of wastewater treatment process is examined by using a wastewater treatment process simulator with the facilities adopting intermittently aerated 2-tank activated sludge process as the object. The following results are obtained from said examination. Based on a fact that the treatment efficiency is influenced greatly by the comparatively miner parts of the process in biological nitrogen and phosphorus removal, a wastewater treatment process simulator, by which the intrinsic process flow, restricting conditions and behaviors of controlling system of each facility can be dealt with, is developed by using object-directional model. As the results of this development, not only the effects approximate to those of actual process can be obtained, but also the trial error and alternation of process flow can be realized in a short time. The serious influence of disappearance of dissolvable organic substance in flow-adjusting tank upon the deterioration of biological phosphorus removal is clarified by the results of the simulation based on the investigation of flowing-in water quality. 12 refs., 13 figs., 4 tabs.

  8. Worldwide clean energy system technology using hydrogen (WE-NET). subtask 9. Investigation of innovative and leading technologies; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 9. Kakushinteki sendoteki gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The WE-NET Project is a long-term project designed to ensure that an energy network technology using hydrogen becomes a reality not later than 2020. So the project cannot remain effective unless constant efforts are made to foresee future trends of technology and optimize it as the making of entire system for the project. In this project, new technologies which are not up for development are also investigated. Their feasibility should be studied, if necessary. From the foregoing point of view, new technologies are studied, collected and evaluated. Thus, useful suggestions and proposals may be made as to the course for the project to follow, as well as its research and development. Proposals highly evaluated up to FY 1995 are the hydrogen-oxygen internal-combustion Stirling`s engine, hydrogen production by solid oxide electrolysis, magnetic refrigeration technology for liquefaction of hydrogen, solar thermal hydrogen production with iron sponge technology, and hydrogen producing technology with photocatalyst. Conceptual investigation themes in FY 1996 are the hydrogen internal-combustion Stirling engine, solar thermal hydrogen production, phototransformation process, and high-temperature steam electrolysis. 9 figs., 54 tabs.

  9. Development of an integrated recycling system for home electric appliances using cryogenic energy. Report of the development achieved in FY 1995; 1995 nendo reinetsu riyo haikibutsu teion hasai sogo recycle system kaihatsu. Seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In FY 1995, the final year of the project as to recycling of large size waste such as discarded home electric appliances as well as energy recovery, operation methods of the comprehensive system were investigated, to design practical systems. Constituent elements and the comprehensive system, which was completed in the prior fiscal year, were operated to evaluate the pilot plant with respect to the categories of operation performance, separation efficiency, and recovery efficiency. Three categories of discarded items were refrigerators, washing machines, and television sets. As a result, it was confirmed that the pilot plant checked out favorably, satisfying all the target values given at the initial stage. For the research of practical system, conceptual design of the practical system, its practical scale, and the economic factors were investigated. In the case of a plant scale of 3 t/h, a trial balance was made of setting equipment costs, fixed costs, fluctuation costs, processing costs, and profit from sale of recovered items with value. As a result, the net cost was about 1,700 yen per wasted hold appliance. In addition, problems in the construction of a practical plant were extracted. 68 figs., 74 tabs.

  10. Report on the FY 1999 research survey on the industrial utilization/development of the biofilm formation mechanism and antifouling substances; 1999 nendo bio film keisei kiko oyobi sogai busshitsu no sangyoteki riyo kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the FY 1999 research on the fouling by marine aufwuchs. The survey is aimed at searching the nature world for active substances for biological antifouling. The fouling mechanism in the ocean is as follows. The adsorption of organisms called the conditioning film first occurs on the surface, and next, bacteria and diatom around the surface form biofilm and cover. After that, biological fouling by large aufwuchs occurs. Therefore, the control of biofilm formation was regarded as most important, and with this as a guidepost, the search was conducted. Using biofilm anti-formation activity and periphytic bacteria anti-growth activity as guideposts, some compounds were searched for. Being aimed at Porifera, in particular, new compounds were isolated from it. Since few of other organisms attaches on the surface of sponge, there is a great possibility of Porifera's producing any anti-fouling substances. Further, it is thought that symbiotic microorganisms of sponge (40% of the total weight) produce various biologically active substances. Synthetic phenethyl amine derivatives were also studied. (NEDO)

  11. Feasibility study of international cooperation on the chemical CO2 fixation and effective utilization technology in FY 1996; 1996 nendo kagakuteki CO2 koteika yuko riyo gijutsu ni kakawaru kokusai kyoryoku kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In this survey, candidate organizations to cooperate internationally in the development of chemical CO2 fixation technologies have been selected, and possible forms of the cooperation each organization would participate in have been examined. The chemical CO2 fixation technology project of RITE (Research Institute of Innovation Technology for the Earth) involves the essential themes of CO2 separation membrane technology, catalytic hydrogenation reaction technology, and hydrogen production/supply technology, as well as the overall system. Through the arrangement, 19 international research institutes were selected as the potential candidates for international research cooperation. Either direct visit or questionnaire by mail was conducted to these institutes. The purposes of international cooperation in each of essential study theme are to review the possibility of improving technologies in each theme by introducing new technologies, and to review the possibilities of promoting practical implementation of chemical CO2 fixation system. The research institutes to be reviewed as partners for joint research are summarized. 10 figs., 16 tabs.

  12. Hybrid utilization of solar energy. Part 2. Performance analyses of heating system with air hybrid collector; Taiyo energy no hybrid riyo ni kansuru kenkyu. 2. Kuki shunetsu hybrid collector wo mochiita danbo system no seino hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Yoshinaga, M.; Okumiya, M. [Nagoya University, Nagoya (Japan)

    1996-10-27

    For the effective utilization of solar energy at houses, a heating system using an air hybrid collector (capable of simultaneously performing heat collection and photovoltaic power generation). As the specimen house, a wooden house of a total floor area of 120m{sup 2} was simulated. Collected air is fanned into a crushed stone heat accumulator (capable of storing one day`s collection) or into a living room. The output of solar cell arrays is put into a heat pump (capable of handling a maximum hourly load of 36,327kJ/h) via an inverter so as to drive the fan (corresponding to average insolation on the heat collecting plate of 10.7MJ/hm{sup 2} and heat collecting efficiency of 40%), and shortage in power if any is supplied from the system interconnection. A hybrid collector, as compared with the conventional air collector, is lower in thermal efficiency but the merit that it exhibits with respect to power generation is far greater than what is needed to counterbalance the demerit. When the hybrid system is in heating operation, there is an ideal heat cycle of collection, accumulation, and radiation when the load is light, but the balance between accumulation and radiation is disturbed when the load is heavy. 4 refs., 8 figs., 3 tabs.

  13. Effects on annual cost of solar/air-heat utilization system of carbon tax and interest rate for a residential house; Jutakuyo taiyo/taikinetsu riyo system no nenkan keihi ni oyobosu tansozei kinri no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Q.; Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan). Faculty of Engineering

    1996-10-27

    In recent years, a system has been proposed that utilizes river heat, air-heat, exhaust heat from a cooler, etc., in addition to natural energy for the heat pump. With the introduction of such system, the amount of energy used and that of CO2 exhaust will be greatly reduced, but annual expenses will be increased as it stands. In order to improve the cost efficiency of the system, a proposal has been made for the introduction of an economic policy such as the carbon tax and a low interest financing system. With these matters in the background, the subject study predicts the production of solar cells in the future and, on the basis of this production, determines the price, conversion efficiency and equipment energy of solar cells in the future. Using these values and taking into consideration the introduction of the carbon tax and the low interest financing system, the optimum area was determined for solar cells and heat concentrators in a future residential solar/air-heat energy system. The carbon tax, being imposed on all CO2 discharges, had a large effect. Moreover, as the tax increased, annual expenses decreased for the solar/air-heat system. 3 refs., 6 figs.

  14. Solid electrolyte membranes and the system to produce hydrogen from thermally decomposed water by solar energy; Taiyo energy riyo ni yoru mizu no chokusetsu netsubunkai kara no suiso seizoyo

    Energy Technology Data Exchange (ETDEWEB)

    Nigara, K.; Watanabe, K.; Kawamura, K.; Kawada, T.; Mizusaki, J.; Ishigame, M. [Tohoku University, Sendai (Japan). Research Institute for Scientific Measurements

    1996-10-27

    For conversion of solar heat to transportable energy, hydrogen production by direct thermal decomposition of water using concentrated high-temperature solar heat was studied. Water vapor is injected into the tubular target with high melting point and high oxygen permeability at high temperature while heating the target by concentrated solar heat over 2000K. Oxygen in decomposed gas is discharged through an oxygen permeable membrane to extract hydrogen. Solid electrolyte is used as one of the target materials. Oxygen gas in the high-oxygen partial pressure site changes into oxygen ion by accepting two electrons at the target surface, and returns to neutral oxygen gas in the low-oxygen partial pressure site by discharging two electrons at the surface after permeation through oxygen vacancy. In the case of n-type solid electrolyte, to obtain constant permeation of a large amount of oxygen, flow of a large amount of electrons is indispensable in the opposite direction to oxygen ion. Among [(ZrO2)(1-x)(CeO2)x](0.9)(CaO)(0.1), materials of 0.4-0.5 in x seems to be useful as the target material. 7 refs., 7 figs.

  15. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 3. Study on the global network; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 3. Global network kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As a part of the WE-NET project, the introduction condition of hydrogen as substituting energy and CO2 reduction effect were analyzed using a global energy model. The WE-NET project aims at global-wide introduction of clean energy by converting abundant renewable clean energy into hydrogen transportable to distant consumers all over the world. The study result in fiscal 1996 is as follows. Undeveloped hydroelectric resources in the world are estimated to be 12 trillion kWh/y equivalent to the existing developed one in the world. Since the cost of the hydroelectric power generation projects over 1000MW in the planning stage is estimated to be 0.02-0.05$/kWh lower than that of other renewable energies, such projects are expected as energy source in the initial stage of the practical WE-NET project. The GREEN model was modified by adding a hydrogen analysis function, and extending an analysis period. The modified model allowed evaluation of the long-term important role of hydrogen energy, in particular, the capability of CO2 gas reduction all over the world. 28 refs., 92 figs., 56 tabs.

  16. FY 1998 annual report on the survey on development, introduction and promotion of urban type multipurpose geothermal utilization techniques; 1998 nendo toshigata tamokuteki chinetsu riyo gijutsu no kaihatsu, donyu, sokushin ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Introduction of geothermal heat pump systems, which depend on temperature differential, is investigated for urban areas, which have large energy demands. Results of the surveys on the current situations of geothermal heat pump (GHP) systems indicate that they have already numbered 300,000 units in USA and totaled more than 50,000 units in Switzerland and Northern European countries, and that they are increasing at an annual rate of higher than 10%. The results also indicate that introduction of these systems are well feasible in Japan, which generally has better topographical conditions than American and European countries, and the GHP system with vertical ground heat exchanger is investigated for its topographical and environmental considerations. These systems could annually abate approximately 52 million tons of CO2 (4.3% decrease), if disseminated to all households. They are also expected to help control the heat island phenomenon, and reduce peak power consumption. The technological problems to be solved before these systems are massively disseminated including development of small scale drilling rigs and preparation of drilling manuals. System standardization and introduction of subsidy systems are also needed to massively disseminate these systems. (NEDO)

  17. Research and development of utilization technology of solar thermal energy system for industrial and other use. International joint technology development for solar energy utilization systems; Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for international joint technology development for solar energy utilization systems. The joint study with an Indonesian research institute takes a model of lumber drying plant for the design and feasibility study. All the parts it needs are technically available in Indonesia, except carbon fiber sheets and electronic devices for controlling purposes. The drying cost is higher than that of a plant which procures charge-free wood fuel, but lower than that of a plant which procures fuel at 30$/t. A cacao drying plant model is also studied. The feasibility study shows that the initial investment for the blowing-up model is much higher by 60% to 100% than that for the conventional plant. Its fuel cost is lower by 11% than that of residual oil but 27% higher than that of wood. 4 figs.

  18. Research and development of system to utilize photovoltaic energy. Study on the scenario for the diffusion of photovoltaic power generating systems; Taiyoko hatsuden riyo sytem no kenkyu kaihatsu. Taiyoko hatsuden donyu fukyu scenario sakusei no tame no chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on a survey to prepare scenario for the diffusion of photovoltaic power generating systems. Introduction target planned with help of a diffusion simulation was verified by calculations using simulation models. The calculations made the following points clear: facility costs and power generation costs for photovoltaic power generation systems, amount of introduced photovoltaic power generation systems, number of facilities introducing photovoltaic power generation systems, policy cost to achieve the target, annual power generation amount, oil substituting effect, carbon dioxide reducing effect, and market sizes. Power generation cost in fiscal 2000 would drop down to 53 yen per kWh in new installation in independent houses and down to 31 yen per kWh in systems used in schools. These reductions are the result of progress in mass production as a result of positively implementing the aiding policies. The required diffusion aiding policies revealed from the simulation results include expansion of subsidy operations for house construction, introduction of the systems into public facilities performed by public organizations, aid to system introduction into private business entities, subsidy to facility investments, and enforcement of power purchase institutions. 3 figs.

  19. Research and development of system to utilize photovoltaic energy. Study on large-scale PV power supply system; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyo energy kyokyu system no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on large-scale PV power supply systems in fiscal 1994. (1) On optimization of large-scale systems, the conceptual design of the model system was carried out which supposes a large-scale integrated PV power generation system in desert area. As a result, a pair of 250kW generation system was designed as minimum one consisting power unit. Its frame and construction method were designed considering weather conditions in the inland of China. (2) On optimization of large-scale transmission systems, as large-scale power transmission systems for PV power generation, the following were studied: AC aerial transmission, DC aerial transmission, superconducting transmission, hydrogen gas pipeline, and LH2 tanker transport. (3) On the influence of large-scale systems, it was estimated that emission control is expected by substituting PV power generation for coal fired power generation, the negative influence on natural environment cannot be supposed, and the favorable economic effect is expected as influence on social environment. 4 tabs.

  20. Research and development of system to utilize photovoltaic energy. Survey on the evaluation of photovoltaic power generation; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoko hatsuden hyoka no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on evaluation of PV power generation in fiscal 1994. (1) On the evaluation technique of energy pay-back time, foreign trial calculation examples by integration method were surveyed. However, there were not many study examples, and the calculation basis of input energy was also ambiguous. The calculation result by input-output analysis in Japan gave the value more than that by integration method, pointing out that indirect input energy is essential. (2) On the evaluation technique of the degree of environmental contribution, CO2 emission of the PV generation system installed on ordinary housing roofs was calculated to estimate reduction of CO2 emission and cost. As a result, PV power generation as reduction measures against CO2 brought a little cost increase. (3) On the latent scale of PV power generation, it was estimated to be nearly 191GW although under no restriction. It was a considerably large value as compared with the current power generation capacity in Japan. 4 tabs.

  1. Numerical method to calculate flow-induced vibration in turbulent flow. 3rd Report. Analysis of vortex-induced vibration in an array of elastically supported tubes; Ranryuba ni okeru ryutai kozotai rensei shindo kaiseki shuho no kaihatsu. 3. Kangun ni okeru uzu reiki shindo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Sadaoka, N.; Umegaki, K. [Hitachi, Ltd., Tokyo (Japan)

    1996-01-25

    A vortex-induced vibration of an array of elastically supported tubes is simulated in two-dimension by using a flow-induced vibration analysis program, which was developed in order to evaluate flow-induced vibration in various components such as heat exchangers. From a comparison of calculated results and experimental data, the following points are observed. (1) For the calculated results in a 5 {times} 5 square array, the flow pattern surrounding the first-row tubes is markedly different from that observed in the second-row or third-row tubes. This flow pattern is the same as that obtained from the experiment. (2) All tubes begin to oscillate due to unsteady fluid force and the oscillating mode is different for each row of tubes. These oscillation patterns show the same tendency in the experiments and it is concluded that the developed method can simulate vortex-induced vibration in an array of elastically supported tubes. 19 refs., 10 figs., 1 tab.

  2. Fiscal 1998 R and D project on global environmental industrial technology. Research result report on DNA analysis and information processing technology for photosynthesis microorganisms (Development of CO{sub 2} fixation and effective use technology by using bacteria and algae); 1998 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Kogosei biseibutsu nado DNA kaiseki joho shori gijutsu no kenkyu (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the fiscal 1998 research result on DNA analysis and information processing technology for photosynthesis microorganisms. On the study on DNA analysis technology by triple-strand formation method, as the comparison study result of a READ method, stable triple- strand formation method and hairpin method, a READ method showed the highest triple-strand formation efficiency for target DNA. On the study on accurate separation technology of specific genes, establishment of protocols was promoted for solid-phase probe technology, subtract technology and leveling technology. On the study on DNA microarray analysis technology by high-efficiency hybridization method, the analysis technology of genes by hybridization method using DNA chips is under investigation. In addition, the high- efficiency analysis technology of specific DNA segments by using an affinity sensor, and the high-accuracy cloning technology for DNA with altered primary structure were also studied. (NEDO)

  3. Report on the results of research and development under a consignment from NEDO of glycoconjugate production utilizing technologies. Development of technologies to fix and effectively utilize carbon dioxide by applying glycoconjugates; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports research results in fiscal 1997 for the `research and development of glycoconjugate production utilizing technologies`. In synthesizing, utilizing and remodeling technologies for glycoconjugates by means of chemical synthesis, studies were performed on developing methods to synthesize Gal {beta}1-3Gal NA(c {alpha})1-0-Serine in preparative scale, synthesizing high mannose type sugars of natural type without protection groups, and linking GlcNA or GalNAc onto partial peptide of fibroblast growth factor (FGF). In synthesizing, utilizing and remodeling technologies for glycoconjugates by using biological methods, studies were carried out, with regard to glycoconjugate synthesizing, utilizing and remodeling technologies utilizing animal cells, on identifying sugar structures of IFN-{gamma} produced from CHO cell line, and isolating CHO cell lines introduced with genes of sugar transferred enzyme GnTIV and/or GnTV. Furthermore, studies were conducted on glycoconjugate synthesizing, utilizing and remodeling technologies utilizing microorganisms, and glycoconjugate structure analyzing technologies. In addition, overall investigation was made on glycoconjugate production utilizing technologies. 113 refs., 76 figs., 18 tabs.

  4. FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing the technology for producing and degrading useful substances using bioconsortia, study was made of the handling technology of bioconsortia, the basic element technology, etc., and the FY 1999 results were reported. In the study of the high-grade utilization technology of lignocellulose/the components, an sample was obtained in which the effect of the bacteria culture supernatant treatment was recognized in the biobleaching by co-treatment of the bacteria culture filtrate - MnP. As to the search for control factor of lignin degrading enzyme and the utilization technology, it was found out that bisphenol A was efficiently degraded by a combination of laccase and mediator production bacteria. Concerning the utilization technology of plant symbiotic bacteria, classification/identification have been finished of approximately 60% of the stored bacteria. In the study of the production technology of the petroleum substituting useful resource, a system was constructed in which immature embryos were used for callus induction and regeneration of plantlets, and plants were regenerated at high frequency via the formation of adventitious embryos. By this, the culture cell with high propagation ability was obtained. (NEDO)

  5. Fiscal 2000 achievement report on project for research and development of technologies for intelligent infrastructure creation and utilization. Development of high-efficiency protein expression system (Development of high-efficiency protein expression system utilizing protein folding mechanism of hyperthermophile); 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu jigyo seika hokokusho. Kokoritsu tanpakushitsu hatsugen system no kaihatsu (Cho konetsukin no tanpakushitsu oritatami kiko wo riyo shita kokoritsu tanpaku hatsugen system no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Studies were conducted aiming at a heterogenic expression system, with E. coli acting as the host, capable of high-efficiency expression of the protein of hyperthermophiles, hyperthermophilic archaebacteria in particular. In this fiscal year, 9 kinds of enzymes were caused by E. coli to express from the genomes of P. Horikoshi, A. pernix, etc., and examined for characteristics. Concerning the L-proline dehydrogenase obtained by the screening of hyperthermophiles of the Thermococcus profundus genus, it was noted that the ferredoxin was possibly a natural acceptor of electrons and that it was possibly an amino acid dehydrogenase of an utterly new category. Furthermore, it was found that the NADkinase of Pyrococcus horikoshii was a unique heat-resistant enzyme which used the inexpensive polyphosphoric acid instead of expensive ATP (adenosine triphosphate), and this justified a hope that it would be quite useful in the industrial production of NADP (H) (nicotinamide adenine dinucleotide phosphate). A success was attained in uniformly refining the glutamate dehydrogenase of hyperthermophilic and inactive Pyrobaculum islandicum produced by E. coli. (NEDO)

  6. FY 1999 report on the results of the project on the industrial science technology R and D. R and D of complex carbonhydrate production/utilization technology (Development of CO2 fixation/effective utilization technology by applying complex carbonhydrate); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugo toushitsu seisan riyo gijutsu no kenkyu kaihatsu (Fukugo toushitsu oyo nisankatanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of making an industrial use of complex carbonhydrate performing an important function in substance recognition, etc., which cannot be realized by only nucleic acid, protein and lipid, the R and D of the basic technology related to the production/utilization were conducted, and the FY 1999 results were reported. In the study of synthesis/utilization/remodeling technology of complex carbonhydrate using the chemical synthesis method, the R and D were made not only on the synthesis of sugar chain but for the synthesis method of the peptide added with sugar chain, that is, glycopeptide. Further, as to the reaction with the aim of the application, there was hope for large-quantity synthesis of milk oligosaccharide by the oxygen method. In the study of the design technology of complex carbonhydrate molecules, the systematical analysis using the model glycopeptide was conducted of effects of the sugar chain addition part and sugar chain structure on the 3D structure and physiological activity. Concerning the synthesis/utilization/remodeling technology of complex carbonhydrate using the biological method, study was made of the animal cell utilization, microorganism utilization, technology of structural analysis of complex carbonhydrate, etc. (NEDO)

  7. Fe(CO)5-catalyzed coprocessing of coal and heavy oil vacuum residue using syngas-water as a hydrogen source; Fe(CO)5 shokubai ni yoru gosei gas-mizu wo suisogen to suru sekitan-jushitsuyu no coprocessing

    Energy Technology Data Exchange (ETDEWEB)

    Hata, K.; Wada, K.; Mitsudo, T. [Kyoto University, Kyoto (Japan)

    1996-10-28

    Improvement in efficiency and profitability of hydrogenation reaction of heavy hydrocarbon resources is the most important matter to be done. In this study, coprocessing of coal and heavy oil vacuum residue was conducted using syngas-water as a hydrogen source. For the investigation of effect of the reaction temperature during the coprocessing of Wandoan coal and Arabian heavy vacuum residue using Fe(CO)5 as a catalyst, the conversion, 66.0% was obtained at 425{degree}C. For the investigation of effect of reaction time, the yield of light fractions further increased during the two stage reaction at 400{degree}C for 60 minutes and at 425{degree}C for 60 minutes. Finally, almost 100% of THF-soluble matter was obtained through the reaction using 2 mmol of Fe(CO)5 catalyst at 400{degree}C for 60 minutes, and hydrogenation of heavy oil was proceeded simultaneously. When comparing coprocessing reactions using three kinds of hydrogen sources, i.e., hydrogen, CO-water, and syngas-water, the conversion yield and oil yield obtained by using syngas-water were similar to those obtained by using hydrogen, which demonstrated the effectiveness of syngas-water. 2 refs., 2 figs., 2 tabs.

  8. Elucidation of hydrogen mobility in tetralin under coal liquefaction conditions using a tritium tracer method. Effects of the addition of H2S and H2O; Tritium tracer ho wo mochiita sekitan ekika hanno jokenka deno tetralin no suiso idosei hyoka. Ryuka suiso oyobi mizu no tenka koka

    Energy Technology Data Exchange (ETDEWEB)

    Kanbe, M.; Saito, M.; Ishihara, A.; Kabe, T. [Tokyo University of Agriculture and Technology, Tokyo (Japan)

    1996-10-28

    It was previously reported that the tritium tracer method is useful for the quantitative consideration of hydrogen behavior in coal during coal liquefaction reaction. Tetralin is excellent hydrogen donating solvent, and is considered as one of the model compounds of coal. In this study, effects of H2S and H2O on the hydrogen exchange reaction between tetralin and gaseous hydrogen labeled by tritium were investigated. It was suggested that the conversion of tetralin and the hydrogen exchange reaction between gaseous hydrogen and tetralin proceed through the radical reaction mechanism with a tetralyl radical as an intermediate product. When H2S existed in this reaction, the hydrogen exchange yield increased drastically without changing the conversion yield. This suggested that the hydrogen exchange reaction proceeds even in the reaction where radical does not give any effect. In the case of H2O addition, the conversion yield and hydrogen exchange rate decreased into a half or one-third. It was suggested that H2O inhibited the formation process of tetralyl radical. 6 refs., 4 figs.

  9. Reaction mechanism of coal liquefaction: hydrogenolysis of model compound using synthetic pyrite as catalysts. 7. Property change of synthetic pyrite catalyst with the time after production; Sekitan ekika hanno kiko (model kagobutsu no hanno). 7. Gosei ryukatetsu shokubai no keiji henka ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Ito, H.; Meno, H.; Uemaki, O.; Shibata, T.; Tsuji, T. [Hokkaido University, Sapporo (Japan)

    1996-10-28

    Reactions of various model compounds were investigated using synthetic pyrites for coal liquefaction. In this study, successive changes of the catalysts were investigated from the reactions of model compounds by using three different synthetic pyrites with the lapse of time after production. Benzyl phenyl ether, dibenzyl, and n-octylbenzene were used as model compounds. Reactions were conducted in an autoclave, into which sample, catalyst, decalin as solvent, and initial hydrogen pressure 10 MPa were charged. The autoclave was held at 450 or 475{degree}C of reaction temperature for 1 hour. The catalyst with a shorter lapse of time after production acted to hydrogen transfer, and inhibited the formation of condensation products due to the stabilization of decomposed fragment. It also acted to isomerization of materials by cutting alkyl side chains. When adding sulfur to the catalyst with longer lapse of time after production under these reaction conditions, it inhibited the formation of condensation products for the reaction of benzyl phenyl ether. However, it did not provide the effect for the reaction of n-octylbenzene. 5 refs., 3 figs.

  10. Fiscal 1997 basic research on coal resource development (equipment development). Report on R and D of new exploration technology (exploration of medium-depth coal deposits in water areas); 1997 nendo sekitan shigen kaihatsu kiso chosa (kiki kaihatsu hen) hokokusho. Shintansa gijutsu chosa kaihatsu (suiiki chushindoso tansa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the research result on development of new coal exploration technology. For a high-precision and high-resolution reflective seismic exploration system, R and D was made on the exploration technology of several meter in resolution for medium-depth (800m) coal deposits under a lake of 2m deep. As a result, the high-frequency and high-power source (150-200Hz in dominant frequency, 700-800m in penetrability) and the high-frequency and high sensitivity receiver (10-1000Hz in frequency band, 35V/PA in sensitivity) were developed successfully, and the positioning system was improved. The final evaluation of these elementary technologies was carried out through demonstration tests, resulting in satisfactory results. For a high-efficiency trial drilling system, the in-bore trouble prevention system for measurement, processing and analysis of drilling data (drilling length, drilling rate, revolution, bit load, torque) and drilling mud data (charge water pressure, charge/discharge water, density, pH, viscosity) was constructed. The outlook for low-cost measurement and a safety during drilling was thus obtained. (NEDO)

  11. Fiscal 1997 survey of overseas coal import base arrangement and promotion. Effects of the expansion of coal trade by IPP on the supply/demand of general coal in Asia; 1997 nendo kaigaitan yunyu kiban seibi sokushin chosa. IPP ni yoru sekitan boeki no kakudai ga Asia no ippantan jukyu ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In consideration of the coal situation in the Asia/Pacific region, a study was made of effects of the expansion of coal trade by IPP on supply/demand of general coal in Asia. When aggregating increases in demand of general coal for electric power use in ten Asian counties, they will be an increase of 130.75 million tons in 2005 over 1997. Fifty nine percent of it is equivalent to the increase by IPP and exceeds the demand expanded by electric utilities operators. Further, a possibility is predicted of contracts and coal quality being different from until now. However, there will be a lot of cases in which plans of constructing power plants in Asia are not so developed as expected except Japan, Korea and Taiwan, and also the effect of the currency crisis starting in Thailand largely affects. In terms of the coal supply, countries which export general coal are only China and Indonesia. Indonesian coal is expanding its production and export rapidly and remarkably. The environmental control in Asia has been tightening, and the fuel selected by IPP is mainly coal rather than natural gas. 40 refs., 94 figs., 179 tabs.

  12. Study of solute incorporation into ice-layer on freeze concentration with ice-lining; Ice lining toketsu noshukuho ni okeru hyosho sochu eno yoshitsu torikomi ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, Y.; Shinozaki, K. [Fujisawa Pharmaceutical Co. Ltd., Osaka (Japan); Hirata, Y. [Osaka University, Osaka (Japan)

    1997-07-10

    The mechanism of solute incorporation into an ice-layer in freeze concentration with ice-lining was studied by changing the impeller speed N and the difference between the brine temperature and the freezing point of the feed solution {Delta}T in 10 kg/m{sup 3} CCNa solution. The effect of N on the apparent partition coefficient of the solute K, is more serious than that of {Delta}T. The growth rate of the ice layer is 10{sup -7} - 10{sup -6}m/s under the condition of {Delta}T=2.8 - 7.9degC and N = 20-400 min{sup -1}. The growth rate had a little effect on solute incorporation into the ice-layer. K values depended on the surface condition of the ice layer, which is effected by the mixing speed of the impeller. The ice layer formed at low mixing speed has a complex rough shape, and has much solute because of adhesion to a large surface area. Therefore, it is recommended that freeze concentration is performed by making an ice layer with smooth surface at high mixing speed. 9 refs., 6 figs.

  13. Relationships between oxygen content, modulation period and superconducting property of Bi-based superconducting oxides. Bi kei sankabtsu chodendotai ni okeru sanso ganryo, hencho kozo oyobi chodendo tokusei no sokan

    Energy Technology Data Exchange (ETDEWEB)

    Deshimaru, Y.; Shimizu, Y.; Miura, N.; Yamazoe, N. (Kyushu Univ., Fukuoka (Japan). Graduate School of Engineering Sciences); Hiroi, Z.; Bando, Y. (Kyoto Univ., Kyoto (Japan). Inst. for Chemical Research)

    1992-09-10

    Two (2223 and 2212) of three superconducting phases in the Pb-doped Bi-Sr-Ca-Cu-O (BSCCO) oxide superconductor were examined for their changes of crystal structures and superconducting properties with changing oxygen content. Their oxygen sorption behavior examined by the temperature-programmed-desorption method showed that both samples desorb trace amounts of oxygen in a temperature range of 350-600 centigrade and the behavior examined by the temperature-programmed oxidation method showed that they absorb (absorb) reversibly oxygen desorbed above in a range of 100-350 centigrade. The critical temperature to bear diamagnetism (Tc) of the 2223 sample fell from 111 K to 96 K as oxygen was desorbed up to 600 centigrade. However, Tc recovers reversibly to the initial value when oxygen was re-absorbed. Contrary to the 2223, the 2212 sample showed the opposite Tc change. Both samples increased in their c-axes lengths and their modulation periods and the changes were reversible respectively. It was pointed out that the Tc behaviors of both sample systems were dependent on the concentration of holes on the CuO2 surfaces. 33 refs., 9 figs.

  14. Technologies adopted in the lean-burn GA15DE engine for improving combustion and controlling the air-fuel ratio; Kogata 4 kito lean burn engine (GA15DE) ni okeru nensho kaizen oyobi seigyo gijutsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Saito, K.; Matsumura, M. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1994-10-07

    This paper summarizes an automotive engine with improved fuel consumption, having realized lean combustion. The lean-burn engine is such an engine that can be operated in an air-fuel ratio compatible in the combustion stability limit and the NOx emission limit by means of combustion improvement, and achieved improvement in fuel consumption as the result. The engine can be expected of higher fuel consumption improving effect than the EGR of the conventional engines because of the lean-burn mechanism. The newly developed lean-burn engine is characterized by less change in its specifications from the basic specifications. Lean fuel burning requires creating a gas mixture condition that is easy to ignite and acquiring a gas flowing field which spreads quickly upon ignition. To achieve these goals, swirl control valves and phase difference cams were disposed. Further, long-discharge coils are used to improve the ignitability. In order to operate the tertiary catalyst more effectively, an A/F sensor that operates in the catalytic area was adopted for the air-fuel ratio feedback control in place of an O2 sensor. The mileage of a vehicle equipped with the lean-burn engine was increased by 17.8% to 20.5 km/l. 2 refs., 13 figs., 2 tabs.

  15. Data acquisition and evaluation analysis on advanced high-efficiency energy system field test project (fiscal 2000); 2000 nendo sendoteki kokoritsu energy system field test jigyo ni okeru data shuyaku oyobi hyoka kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Field tests have been performed on the next generation phosphoric acid fuel cell power generation systems to collect and analyze the long-term operation data and trouble cases by introducing the final proliferation pattern into the actual demand on a trial basis. This paper reports the achievements in fiscal 2000. The locations of executing the field tests in fiscal 2000 are the 15 sites, including the NTT Central Training Center, and the Environment and Energy Exploratirium. Measurements were carried out at each test site on fuel gas consumption, fuel cell output power amount, utilized quantity of heat at low temperatures, utilized quantity of heat at elevated temperatures, and discarded quantity of heat. In addition, the total demand power amount and the shutdown information were also put into order. As a result of the evaluation analysis, the second factory of Senhoku Manufactory recorded the longest operation time of 23,777 hours, whose operation factor has reached 92%. Five systems had the continuous operation time exceeded 5,000 hours. The power generation efficiency was about 40% in a system using the town gas 13A fuel, wherein the total efficiency was 90% or greater. The largest number of failures in fiscal 2000 was seven at Tochigi Factory of Kirin Brewery, whose average number of failure was 1.6 a year. (NEDO)

  16. Considerations on FEM modeling in analyzing buckling and plastic collapse of a detection control; Boto panel no zakutsu sosei hokai kaiseki ni okeru FEM model ka ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yao, T.; Fujikubo, M.; Yanagihara, D.; Irisawa, M. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1997-10-01

    Buckling and plastic collapse of upper decks and bottom outer plates of a hull results directly in longitudinal bending collapse of the hull. Therefore, discussions were given on analysis for pressure destruction strength of a detection control panel which assumes an upper deck and a bottom outer plate. Pressure destruction behavior of the panting panel is a complex phenomenon accompanying non-linearity and geometrical non-linearity of the materials. Its whole phenomenon may be analyzed by using the finite element method (FEM) as a principle, but the analysis is not efficient. Therefore, considerations were given in relation to modeling when using the FEM. The considerations were given on a panel attached with flat steel panting members with respect to the modeling scope which considers the buckling mode according to the aspect ratio of the panel partitioned by the deflection control members. If the local buckling mode of the panel is an even number wave mode in the longitudinal direction, a triple span model is required. A modeling scope for a case of being subjected to water pressure and in-plane compression was considered on a panel attached with angle-type steel members having non-symmetric cross section. In this case, a triple bay model is more preferable to reproduce the behavior under water pressure loading. 1 ref., 6 figs.

  17. Internal friction and microplasticity of carbon-fiber-reinforced SiC ceramics; Tanso sen`i kyoka SiC ceramics no hakai zenku katei ni okeru naibu masatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ogawa, H.; Nishino, Y.; Asano, S. [Nagoya Institute of Technology, Nagoya (Japan)

    1995-08-20

    Mechanical responses of carbon-fiber-reinforced SiC ceramics before fracture were measured in the strain range below 2 {times} 10{sup {minus}3} by two experimental methods: mechanical hysteresis and internal friction. Load-deflection curves were obtained by the three-point bending deformation in loading-unloading cycles. A little permanent strain was found after the first cycle even in the range where fracture never occurred. A closed hysteresis loop was observed after several cycles and stabilized with a symmetrical shape after more than twenty cycles. Such a stabilized hysteresis loop is attributed to the steady-state microplastic deformation and may cause the amplitude-dependent internal friction. Internal friction was measured in the fundamental mode of free-free resonant vibration as a function of strain amplitude. With increasing the amount of prestrain in the bending deformation, internal friction increased and became sensitive to the strain amplitude. The amplitude-dependent internal friction in the composites is considered to originate from fiber pull-out or microcrack propagation. The internal friction data were analyzed on the basis of the microplasticity theory and converted into the plastic strain expressed as a function of stress. Therefore, it becomes possible to non-destructively study the forerunning process of fracture of the fiber-reinforced ceramics. 23 refs., 6 figs.

  18. 55th electric science promotion prize (progress prize). Demonstration of optical soliton transmission on OPGW first in the world; Dai 55 kai denki gakujutsu shinkosho (shinposho) jusho. Seiaihatsu no OPGW ni okeru hikari soriton denso no jissho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-10

    Electric science promotion prize (progress prize) is given to `Person who newly proposed a new concept, theory, material, device, system and method on electrical science and technology, or demonstrated these proposals` by the commendation committee of Institute of Electrical Engineers of Japan every year. Eight promotion prizes including that for Kansai Electric Power`s `Demonstration of optical soliton transmission on OPGW first in the world` were given. This research succeeded in development of the transmission/ receiving device suitable for optical soliton transmission, and the prediction method of an optimum transmission condition by computer simulation. In addition, this research succeeded in 10Gbit transmission of 784km and 40Gbit transmission (4-wave multiplex) of 392km by applying the above research result to Okurobe trunk line OPGW (98.2km). This demonstration of optical soliton transmission on OPGW is first in the world. (NEDO)

  19. Detection of the oscillation mode of measured waveforms in power systems by Prony analysis; Puroni kaisekiho ni yoru denryoku keito ni okeru jissoku hakei no doyo mode kenshutsu ni tsuite