WorldWideScience

Sample records for oil production wastewater

  1. Mackerel biodiesel production from the wastewater containing fish oil

    International Nuclear Information System (INIS)

    Wu, Y.P.; Huang, H.M.; Lin, Y.F.; Huang, W.D.; Huang, Y.J.

    2014-01-01

    Marine fish such as mackerel are important for coastal fisheries in Taiwan. Nearly 60,000 tons of mackerel are produced in Suao, I-lan, Taiwan every year. In this study, oil from the discarded parts of mackerel fish contained in wastewater stream were used as the raw material to produce biodiesel through transesterification reaction. The major fuel properties of MB (mackerel biodiesel), including the iodine value, dynamic viscosity, flash point, and heat value, were determined and compared with sunflower seed oil methyl ester (SFM), JCB (Jatropha curcas biodiesel), and premium diesel (D). MB had a higher iodine value, dynamic viscosity, density, and flash point, but a lower heat value, than did D. MB was also used as fuel in a regular diesel engine to verify its emission characteristics. The MB fuel used for exhaust emission test included pure MB (MB100) and a 20% MB blend with premium diesel (MB20). The exhaust emission of MB was also compared with the exhaust emissions of D and JCB. The results showed that MB20 provided a significant reduction in NO, NO x , and SO 2 emissions under varied engine loads, and required no engine modification. - Highlights: • Biodiesel was produced from wastewater containing mackerel fish oil. • Mackerel biodiesel is compared with Jatropha biodiesel and sunflower seed biodiesel. • MBE (mackerel biodiesel) was found to contain higher amount of unsaturated fatty acids. • Mackerel biodiesel, diesel, and Jatropha biodiesel emissions are compared

  2. Electrocoagulation of palm oil mill effluent as wastewater treatment and hydrogen production using electrode aluminum.

    Science.gov (United States)

    Nasution, M Ansori; Yaakob, Z; Ali, Ehsan; Tasirin, S M; Abdullah, S R S

    2011-01-01

    Palm oil mill effluent (POME) is highly polluting wastewater generated from the palm oil milling process. Palm oil mill effluent was used as an electrolyte without any additive or pretreatment to perform electrocoagulation (EC) using electricity (direct current) ranging from 2 to 4 volts in the presence of aluminum electrodes with a reactor volume of 20 L. The production of hydrogen gas, removal of chemical oxygen demand (COD), and turbidity as a result of electrocoagulation of POME were determined. The results show that EC can reduce the COD and turbidity of POME by 57 and 62%, respectively, in addition to the 42% hydrogen production. Hydrogen production was also helpful to remove the lighter suspended solids toward the surface. The production of Al(OH)XHO at the aluminum electrode (anode) was responsible for the flocculation-coagulation process of suspended solids followed by sedimentation under gravity. The production of hydrogen gas from POME during EC was also compared with hydrogen gas production by electrolysis of tap water at pH 4 and tap water without pH adjustment under the same conditions. The main advantage of this study is to produce hydrogen gas while treating POME with EC to reduce COD and turbidity effectively. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  3. Production of methyl ester from oil in the wastewater pond of a palm oil factory

    Directory of Open Access Journals (Sweden)

    Tongurai, C.

    2007-11-01

    Full Text Available This research studied the suitable technique for the production of methyl ester from waste palm oil in the water pond of a palm oil mill. The composition of the waste palm oil was 73.82% fatty acid, 5.07% triglyceride, 3.39% diglyceride and 17.76% unknown compounds. The unknown compounds were separated via simple distillation carried out at a temperature range of 300-350oC.First, the experiments were carried out in screw capped bottles using filtrated as-received waste oil as the reactant. The esterification and transesterification process were conducted using sulfuric acid catalyst in a methanol solution. The key parameters studied were mole ratio of waste oil to methanol (1:1 to 1:72, amount of catalyst from 0.1-20 v/w% of the reactant, temperature range of 60-98oC and reaction time range of 15-180 minutes. Thin Layer Chromatography (TLC analysis showed 85-90% purity of methyl ester with 4-5% of mono-, di-, and triglycerides and fatty acids and about 5-10% of the unknown compounds for the best condition. The resulting yield of biodiesel was 84-88%. Eradication of contaminants by distillation gave about a 75% distillate yield. Distilled waste palm oil was esterified and transesterified using the previous optimum condition of as-received waste oil, but the reaction time and temperature were varied. The optimal result was obtained by using distilled waste palm oil to methanol molar ratio of 1:8, sulfuric acid of 1 v/w% of reactant, reaction temperature of 70oC and reaction time of 1 hour. TLC analysis indicated a biodiesel composition of methyl ester, free fatty acid, diglyceride and monoglyceride of 96.39%, 3.20%, 0.24% and 0.17%, respectively. The yield of biodiesel was 96-98% having physical fuel properties according to Thailand standard for methyl esterFinally, the distilled waste palm oil was esterified using a 3 liters continuous stirred-tank reactor (CSTR. Using the suitable condition for the batch process and an hour retention time, the

  4. A GIS based national assessment of algal bio-oil production potential through flue gas and wastewater co-utilization

    International Nuclear Information System (INIS)

    Orfield, Nolan D.; Keoleian, Gregory A.; Love, Nancy G.

    2014-01-01

    The high theoretical productivity of microalgae makes it a promising energy crop, but economically viable large-scale production facilities have yet to emerge. Coupling algae cultivation ponds with flue gas emissions from power utilities to provide carbon dioxide and municipal wastewater to provide nutrients has been recommended as a solution. This flue gas and wastewater co-utilization (FWC) strategy not only reduces the upstream impacts and costs associated with providing inputs, but also provides a credit for wastewater treatment, a service currently required to reduce production costs to a viable level. This study provides the first national assessment of the potential for producing algal bio-oil in the United States using FWC. Spatial-temporal algae growth was simulated using solar radiation and temperature data to calculate the average annual algae yield for any location, which significantly impacts feasibility. The results of this model were integrated into a geospatial analysis which establishes the economically viable bio-oil production potential of FWC by accounting for the relative abundance of the input resources and their proximity. At most, 1.7 billion liters of bio-oil could be produced annually in a manner economically competitive with crude oil prices of $80 per barrel. The amount of nutrients in wastewater limits yields to 20.5 L of bio-oil per capita annually, and climatic constraints further reduce this potential by nearly 60%. Carbon dioxide constraints play a negligible role. Although the bio-oil production potential of FWC is relatively small, it does provide an opportunity to increase national biofuel output while providing a needed service. - Highlights: • Spatial-temporal algae growth was simulated using historical climate data. • A geospatial overlay analysis was used to assess national production potential. • Nutrient availability in wastewater is most limiting. • At most, 1.7 billion liters of algal biofuel per year could be

  5. Comparative Studies of Oleaginous Fungal Strains (Mucor circinelloides and Trichoderma reesei) for Effective Wastewater Treatment and Bio-Oil Production

    OpenAIRE

    Bhanja, Anshuman; Minde, Gauri; Magdum, Sandip; Kalyanraman, V.

    2014-01-01

    Biological wastewater treatment typically requires the use of bacteria for degradation of carbonaceous and nitrogenous compounds present in wastewater. The high lipid containing biomass can be used to extract oil and the contents can be termed as bio-oil (or biodiesel or myco-diesel after transesterification). The separate experiments were conducted on actual wastewater samples with 5% v/v inoculum of Mucor circinelloides MTCC1297 and Trichoderma reesei NCIM992 strains. The observed reduction...

  6. Edible Oil Industry Wastewater Treatment by Microfiltration with Ceramic Membrane

    OpenAIRE

    Zita Šereš; Dragana Šoronja Simović; Ljubica Dokić; Lidietta Giorno; Biljana Pajin; Cecilia Hodur; Nikola Maravić

    2016-01-01

    Membrane technology is convenient for separation of suspended solids, colloids and high molecular weight materials that are present. The idea is that the waste stream from edible oil industry, after the separation of oil by using skimmers is subjected to microfiltration and the obtained permeate can be used again in the production process. The wastewater from edible oil industry was used for the microfiltration. For the microfiltration of this effluent a tubular membrane was used with a pore ...

  7. Discharges of produced waters from oil and gas extraction via wastewater treatment plants are sources of disinfection by-products to receiving streams

    Science.gov (United States)

    Hladik, Michelle; Focazio, Michael J.; Engle, Mark

    2014-01-01

    Fluids co-produced with oil and gas production (produced waters) are often brines that contain elevated concentrations of bromide. Bromide is an important precursor of several toxic disinfection by-products (DBPs) and the treatment of produced water may lead to more brominated DBPs. To determine if wastewater treatment plants that accept produced waters discharge greater amounts of brominated DBPs, water samples were collected in Pennsylvania from four sites along a large river including an upstream site, a site below a publicly owned wastewater treatment plant (POTW) outfall (does not accept produced water), a site below an oil and gas commercial wastewater treatment plant (CWT) outfall, and downstream of the POTW and CWT. Of 29 DBPs analyzed, the site at the POTW outfall had the highest number detected (six) ranging in concentration from 0.01 to 0.09 μg L− 1 with a similar mixture of DBPs that have been detected at POTW outfalls elsewhere in the United States. The DBP profile at the CWT outfall was much different, although only two DBPs, dibromochloronitromethane (DBCNM) and chloroform, were detected, DBCNM was found at relatively high concentrations (up to 8.5 μg L− 1). The water at the CWT outfall also had a mixture of inorganic and organic precursors including elevated concentrations of bromide (75 mg L− 1) and other organic DBP precursors (phenol at 15 μg L− 1). To corroborate these DBP results, samples were collected in Pennsylvania from additional POTW and CWT outfalls that accept produced waters. The additional CWT also had high concentrations of DBCNM (3.1 μg L− 1) while the POTWs that accept produced waters had elevated numbers (up to 15) and concentrations of DBPs, especially brominated and iodinated THMs (up to 12 μg L− 1 total THM concentration). Therefore, produced water brines that have been disinfected are potential sources of DBPs along with DBP precursors to streams wherever these wastewaters are discharged.

  8. Optimization of biogas production from olive-oil mill wastewater, by codigesting with diluted poultry-manure

    International Nuclear Information System (INIS)

    Gelegenis, John; Georgakakis, Dimitris; Angelidaki, Irini; Christopoulou, Nicholetta; Goumenaki, Maria

    2007-01-01

    Optimization of biogas production from olive-mill wastewater (OMW) was attempted by codigesting with diluted poultry-manure (DPM) at mesophilic conditions. A series of laboratory experiments were performed in continuously-operating reactors, fed with mixtures of OMW and DPM at various concentrations. It was concluded that codigestion of OMW with DPM is possible without any dilution of OMW or addition of any chemicals. Biogas production was slightly higher when OMW was added to DPM up to a critical concentration (about 40%, expressed as contribution of OMW to the volatile solids of the mixture), after which production is decreased. The results were further verified by scaling up to a continuously-operating pilot-plant reactor digesting DPM, and confirmed that no negative impact was imposed by adding OMW up to the above critical value

  9. STUDY ON OIL WASTEWATER TREATMENT WITH POLYMERIC REAGENTS

    Directory of Open Access Journals (Sweden)

    RODICA BUCUROIU

    2016-04-01

    Full Text Available Used the polymeric reagents in oil wastewater treatment is an effective method of eliminate hydrocarbons. The present study aims to finding reagents that lead to lowering of extractible (EXT, suspended solids (SS and chemical oxygen demand (COD of industrial wastewater from washing cars in loading ramps petroleum products. For this purpose five reagents were tested, namely: polyamines, cationic polyacrylamides, polydiallydimethyl ammonium chloride (PolyDADMAC, melamine formaldehyde polymer resin and polydicyandiamide polymer resin. Obtaining removal degrees over 80 % justifies using this method in the industrial practice.

  10. Bacteria Provide Cleanup of Oil Spills, Wastewater

    Science.gov (United States)

    2010-01-01

    Through Small Business Innovation Research (SBIR) contracts with Marshall Space Flight Center, Micro-Bac International Inc., of Round Rock, Texas, developed a phototrophic cell for water purification in space. Inside the cell: millions of photosynthetic bacteria. Micro-Bac proceeded to commercialize the bacterial formulation it developed for the SBIR project. The formulation is now used for the remediation of wastewater systems and waste from livestock farms and food manufacturers. Strains of the SBIR-derived bacteria also feature in microbial solutions that treat environmentally damaging oil spills, such as that resulting from the catastrophic 2010 Deepwater Horizon oil rig explosion in the Gulf of Mexico.

  11. Water issues associated with heavy oil production.

    Energy Technology Data Exchange (ETDEWEB)

    Veil, J. A.; Quinn, J. J.; Environmental Science Division

    2008-11-28

    Crude oil occurs in many different forms throughout the world. An important characteristic of crude oil that affects the ease with which it can be produced is its density and viscosity. Lighter crude oil typically can be produced more easily and at lower cost than heavier crude oil. Historically, much of the nation's oil supply came from domestic or international light or medium crude oil sources. California's extensive heavy oil production for more than a century is a notable exception. Oil and gas companies are actively looking toward heavier crude oil sources to help meet demands and to take advantage of large heavy oil reserves located in North and South America. Heavy oil includes very viscous oil resources like those found in some fields in California and Venezuela, oil shale, and tar sands (called oil sands in Canada). These are described in more detail in the next chapter. Water is integrally associated with conventional oil production. Produced water is the largest byproduct associated with oil production. The cost of managing large volumes of produced water is an important component of the overall cost of producing oil. Most mature oil fields rely on injected water to maintain formation pressure during production. The processes involved with heavy oil production often require external water supplies for steam generation, washing, and other steps. While some heavy oil processes generate produced water, others generate different types of industrial wastewater. Management and disposition of the wastewater presents challenges and costs for the operators. This report describes water requirements relating to heavy oil production and potential sources for that water. The report also describes how water is used and the resulting water quality impacts associated with heavy oil production.

  12. Biodiesel production from algae grown on food industry wastewater.

    Science.gov (United States)

    Mureed, Khadija; Kanwal, Shamsa; Hussain, Azhar; Noureen, Shamaila; Hussain, Sabir; Ahmad, Shakeel; Ahmad, Maqshoof; Waqas, Rashid

    2018-04-10

    Algae have an ample potential to produce biodiesel from spent wash of food industry. In addition, it is cheaper and presents an environment friendly way to handle food industry wastewater. This study was conducted to optimize the growth of microalgal strains and to assess biodiesel production potential of algae using untreated food industry wastewater as a source of nutrients. The food industry wastewater was collected and analyzed for its physicochemical characteristics. Different dilutions (10, 20, 40, 80, and 100%) of this wastewater were made with distilled water, and growth of two microalgal strains (Cladophora sp. and Spyrogyra sp.) was recorded. Each type of wastewater was inoculated with microalgae, and biomass was harvested after 7 days. The growth of both strains was also evaluated at varying temperatures, pH and light periods to optimize the algal growth for enhanced biodiesel production. After optimization, biodiesel production by Spyrogyra sp. was recorded in real food industry wastewater. The algal biomass increased with increasing level of food industry wastewater and was at maximum with 100% wastewater. Moreover, statistically similar results were found with algal growth on 100% wastewater and also on Bristol's media. The Cladophora sp. produced higher biomass than Spyrogyra sp. while growing on food industry wastewater. The optimal growth of both microalgal strains was observed at temperature 30 °C, pH: 8, light 24 h. Cladophora sp. was further evaluated for biodiesel production while growing on 100% wastewater and found that this strain produced high level of oil and biodiesel. Algae have an ample potential to produce biodiesel from spent wash of food industry. In addition, it is cheaper and presents an environment friendly way to handle food industry wastewater.

  13. Electrochemical treatment of olive oil mill wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Longhi, P.; Fiori, G [Milan Univ., Milan (Italy). Dept. of Physical Chemistry and Electrochemistry; Vodopivec, B. [Milan Univ. Bicocca, Milan (Italy). Dept. of Biotechnologies and Biosciences

    2001-04-01

    The possibility of oxidizing at a PbO{sub 2} anode the phenols and polyphenols, present in the olive oil mill wastewater, has been studied as a pre-treatment for the submission of such wastewater to the traditional biological treatments. The results obtained operating at current densities ranging 500 to 2000 A/m{sup 2} show that it is possible to reduce the concentration of the phenolic components, which interfere with the biological treatments, down to low values without decreasing too much the total organic content of the wastewater. [Italian] E' stata studiata la possibilita' di ossidare anodicamente i componenti fenolici delle acque reflue di frantoio, quale pretrattamento delle stesse prima del loro invio ai processi di trattamento biologico. I risultati ottenuti impiegando PbO{sub 2} quale materiale anodico e operando con densita' di corrente comprese tra 500 e 2000 A/m{sup 2} mostrano come sia possibile eliminare, o almeno diminuire sino a concentrazioni accettabili, dalle acque di frantoio i fenoli e i polifenoli, che interferiscono con i normali trattamenti biologici, senza diminuire eccessivamente il carico organico totale.

  14. Environmental control technology for shale oil wastewaters

    Energy Technology Data Exchange (ETDEWEB)

    Mercer, B.W.; Wakamiya, W.; Bell, N.E.; Mason, M.J.; Spencer, R.R.; English, C.J.; Riley, R.G.

    1982-09-01

    This report summarizes the results of studies conducted at Pacific Northwest Laboratory from 1976 to 1982 on environmental control technology for shale oil wastewaters. Experimental studies conducted during the course of the program were focused largely on the treatment and disposal of retort water, particularly water produced by in situ retorting of oil shale. Alternative methods were evaluated for the treatment and disposal of retort water and minewater. Treatment and disposal processes evaluated for retort water include evaporation for separation of water from both inorganic and organic pollutants; steam stripping for ammonia and volatile organics removal; activated sludge and anaerobic digestion for removal of biodegradable organics and other oxidizable substances; carbon adsorption for removal of nonbiodegradable organics; chemical coagulation for removal of suspended matter and heavy metals; wet air oxidation and solvent extraction for removal of organics; and land disposal and underground injection for disposal of retort water. Methods for the treatment of minewater include chemical processing and ion exchange for fluoride and boron removal. Preliminary cost estimates are given for several retort water treatment processes.

  15. Modification of Wastewater Treatment Technology at Cottonseed Oil Plant

    Directory of Open Access Journals (Sweden)

    Alshabab Mary Shick

    2016-01-01

    Full Text Available Wastewaters from cottonseed oil producing plant in Syria were studied in laboratory experiments. Aim of the study was to suggest modification of wastewater treatment technology in order to increase its efficiency. Concentration of pollutants in wastewaters was controlled by measurement of COD. According to the results of experiments it was suggested to decrease significantly (8-20 times dosages of reagents (acidifier, coagulant, flocculant in several actual stages of treatment (acidification, separation, coagulation and sedimentation and add stage of dispersed air flotation before coagulation treatment. The modified wastewater treatment technology would reduce COD to the values allowed for irrigation waters by Syrian National Standard.

  16. Organic pollutant removal from edible oil process wastewater using electrocoagulation

    Science.gov (United States)

    Sharma, S.; Can, O. T.; Hammed, M.; Nawarathna, D.; Simsek, H.

    2018-03-01

    Wastewaters generated from vegetable oil industries contain a high concentration of organic pollutants that are detrimental to the aquatic ecosystem. Electrochemical processes are gaining importance in the treatment of inorganic and resistant organic pollutants in wastewaters. In this study, electrocoagulation (EC) was applied to remove organic pollutants and oil and grease from canola oil wastewater using aluminum (Al) and iron (Fe) electrodes. The application of EC in the wastewater achieved more than 80% removal of organic carbon and nearly 100% removal of suspended solids (SS). The effectiveness of EC is influenced mainly by current density, pH, electrolyte (NaCl), electrode contact time and electrode type. It was observed that Al electrode combination yielded better removal at a lesser time compared to that of Fe electrodes. However, varying current densities had its significance in terms of coagulation time only. Increase in current density achieved decrease in coagulation time. Both Al and Fe could remove between 52-59% of oil and grease from canola oil wastewater

  17. Biological hydrogen production from industrial wastewaters

    Energy Technology Data Exchange (ETDEWEB)

    Peixoto, Guilherme; Pantoja Filho, Jorge Luis Rodrigues; Zaiat, Marcelo [Universidade de Sao Paulo (EESC/USP), Sao Carlos, SP (Brazil). School of Engineering. Dept. Hydraulics and Sanitation], Email: peixoto@sc.usp.br

    2010-07-01

    This research evaluates the potential for producing hydrogen in anaerobic reactors using industrial wastewaters (glycerol from bio diesel production, wastewater from the parboilization of rice, and vinasse from ethanol production). In a complementary experiment the soluble products formed during hydrogen production were evaluated for methane generation. The assays were performed in batch reactors with 2 liters volume, and sucrose was used as a control substrate. The acidogenic inoculum was taken from a packed-bed reactor used to produce hydrogen from a sucrose-based synthetic substrate. The methanogenic inoculum was taken from an upflow anaerobic sludge blanket reactor treating poultry slaughterhouse wastewater. Hydrogen was produced from rice parboilization wastewater (24.27 ml H{sub 2} g{sup -1} COD) vinasse (22.75 ml H{sub 2} g{sup -1} COD) and sucrose (25.60 ml H{sub 2} g{sup -1} COD), while glycerol only showed potential for methane generation. (author)

  18. Photocatalytic Degradation of Oil using Polyvinylidene Fluoride/Titanium Dioxide Composite Membrane for Oily Wastewater Treatment

    Directory of Open Access Journals (Sweden)

    Rusli Ummi Nadiah

    2016-01-01

    Full Text Available Production of industrial wastewater is increasing as the oil and gas industry grows rapidly over the years. The constituents in the industrial wastewater such as organic and inorganic matters, dispersed and lubricant oil and metals which have high toxicity become the major concern to the environment and ecosystem. There are many technologies are being used for oil removal from industrial wastewater. However, there are still needs to find an effective technology to treat oily wastewater before in can be discharge safely to the environment. Membrane technology is an attractive separation technology to treat oily wastewater. The aim of this study is to fabricate polyvinylidene/titanium dioxide (PVDF/TiO2 composite membrane with further treatment using hot pressed method to enhance the adhesion between TiO2 with the membrane surfaces. In this study the structural and physical properties of fabricated membrane were conducted using X-ray diffraction (XRD and Fourier transform infrared spectroscopy (FTIR respectively. The photocatalytic degradation of oil was measured using UV-Vis Spectroscopy. The FTIR results confirmed that, hot pressed PVDF/TiO2 membrane TiO2 was successfully deposited onto PVDF membranes surface and XRD results shows that the XRD pattern of PVDF//TiO2 found that the crystalline structure was remained unchanged after hot pressed. Clear water was obtained after synthetic oily wastewater was exposed to visible light for at least 6 hours. In conclusion, PVDF/TiO2 composite membrane can be a potential candidate to degrade oil in oily wastewater and suggested to possess an excellent performance if perform simultaneously with membrane separation process.

  19. Recovery of useful chemicals from palm oil mill wastewater

    Science.gov (United States)

    Ratanaporn, Yuangsawad; Duangkamol, Na-Ranong; Teruoki, Tago; Takao, Masuda

    2017-11-01

    A two-step process consisting of pyrolysis of dried sludge and catalytic upgrading of pyrolysed liquid was proposed. Wastewater from a palm oil mill was separated to solid cake and liquid by filtration. The solid cake was dried and pyrolysed at 773 K. Liquid product obtained from the pyrolysis had two immiscible aqueous and oil phases (PL-A and PL-O). Identification of chemicals in PL-A and PL-O indicated that both phases contained various chemicals with unsaturated bonds, such as carboxylic acids and alcohols, however, most of the chemicals could not be identified. Catalytic upgrading of PL-A and PL-O over ZrO2·FeOx were separately performed using a fixed bed reactor at various conditions, T = 513-723 K and mass of catalyst to feed rate = 0.25-10 h. The main components in the liquid products of PL-A upgrading were methanol and acetone whereas they were acetone and phenol in the case of PL-O upgrading. More than 15% of carbon in raw material was deposited on the catalyst. To reduce the carbon deposition, the used catalyst was treated with air at 823 K. This simple treatment could reasonably regenerate the catalyst only for the case of PL-A catalytic upgrading.

  20. Rapid estimation of organic nitrogen in oil shale wastewaters

    Energy Technology Data Exchange (ETDEWEB)

    Jones, B.M.; Harris, G.J.; Daughton, C.G.

    1984-03-01

    Many of the characteristics of oil shale process wastewaters (e.g., malodors, color, and resistance to biotreatment) are imparted by numerous nitrogen heterocycles and aromatic amines. For the frequent performance assessment of waste treatment procsses designed to remove these nitrogenous organic compounds, a rapid and colligative measurement of organic nitrogen is essential.

  1. Oxygen enriched air using membrane for palm oil wastewater treatment

    Directory of Open Access Journals (Sweden)

    Ramlah Mohd Tajuddin

    2002-11-01

    Full Text Available A research aimed to explore new method of aeration using oxygen enriched air performance on BOD reduction of palm oil wastewater was conducted. The oxygen enriched air was obtained from an Oxygen Enriched System (OES developed using asymmetric polysulfone hollow fiber membrane with composition consisting of PSF: 22%, DMAc: 31.8%, THF: 31.8%, EtOH: 14.4%. Palm oil wastewater samples were taken from facultative pond effluent. These samples were tested for its initial biochemical oxygen demand (BOD, total suspended solids (TSS, pH, conductivity, turbidity, dissolved oxygen (DO, suspended solids (SS, and total dissolved solids (TDS before being subjected to two modes of aeration system, that is diffused air and oxygen enriched air. These water quality concentrations were tested for every 20 minutes for two-hour period during the aeration process. Results of BOD, TSS, pH, conductivity, DO, SS and TDS concentrations against time of samples from the two modes of aeration were then compared. It was found that DO concentration achieved in oxygen enriched air aeration was better than aeration using diffused air system. Aeration using OES improve the DO concentration in the wastewater and thus improve the BOD reduction and also influence other physical characteristics of wastewater. This phenomenon indicates the advantage of using air with higher oxygen concentration for wastewater aeration instead of diffused air system.

  2. Nanotechnologies in oil production

    International Nuclear Information System (INIS)

    Alieva, M.K; Kazimov, F.K.; Ismailov, E.

    2010-01-01

    Extraction of remaining, laboriously developed oil reserves at the last stage of development of deposits require drastically improved methods of oil recovery. From this point of view it is more expedient to apply high-tech nanotechnologies. Application of metal nanoparticles in solutions consisting of conventional reagents (deemulgators, SAA and etc.) allows to improve their rheology considerably to increase permaibility and washing of highly viscous components from the smallest pores. Thus, nanofluids influence layer system on atomic-molecular-ionic level which will lead to a complex synergetic effect from the application of nanotechnologies in oil and gas production.

  3. Watershed-Scale Impacts from Surface Water Disposal of Oil and Gas Wastewater in Western Pennsylvania.

    Science.gov (United States)

    Burgos, William D; Castillo-Meza, Luis; Tasker, Travis L; Geeza, Thomas J; Drohan, Patrick J; Liu, Xiaofeng; Landis, Joshua D; Blotevogel, Jens; McLaughlin, Molly; Borch, Thomas; Warner, Nathaniel R

    2017-08-01

    Combining horizontal drilling with high volume hydraulic fracturing has increased extraction of hydrocarbons from low-permeability oil and gas (O&G) formations across the United States; accompanied by increased wastewater production. Surface water discharges of O&G wastewater by centralized waste treatment (CWT) plants pose risks to aquatic and human health. We evaluated the impact of surface water disposal of O&G wastewater from CWT plants upstream of the Conemaugh River Lake (dam controlled reservoir) in western Pennsylvania. Regulatory compliance data were collected to calculate annual contaminant loads (Ba, Cl, total dissolved solids (TDS)) to document historical industrial activity. In this study, two CWT plants 10 and 19 km upstream of a reservoir left geochemical signatures in sediments and porewaters corresponding to peak industrial activity that occurred 5 to 10 years earlier. Sediment cores were sectioned for the collection of paired samples of sediment and porewater, and analyzed for analytes to identify unconventional O&G wastewater disposal. Sediment layers corresponding to the years of maximum O&G wastewater disposal contained higher concentrations of salts, alkaline earth metals, and organic chemicals. Isotopic ratios of 226 Ra /228 Ra and 87 Sr /86 Sr identified that peak concentrations of Ra and Sr were likely sourced from wastewaters that originated from the Marcellus Shale formation.

  4. Removal of mineral oil and wastewater pollutants using hard coal

    Directory of Open Access Journals (Sweden)

    BRANISLAV R. SIMONOVIĆ

    2009-05-01

    Full Text Available This study investigates the use of hard coal as an adsorbent for removal of mineral oil from wastewater. In order to determine the efficiency of hard coal as an adsorbent of mineral oil, process parameters such as sorption capacity (in static and dynamic conditions, temperature, pH, contact time, flow rate, and chemical pretreatment were evaluated in a series of batch and continuous flow experiments. There were significant differences in the mineral oil removal for various pH values examined. The adsorption of mineral oil increased as pH values diverged from 7 (neutral. At lower temperatures, the adsorption was notably higher. The wastewater flow rate was adjusted to achieve optimal water purification. Equilibrium was reached after 10 h in static conditions. At that time, more than 99% of mineral oil had been removed. At the beginning of the filtering process, the adsorption rate increased rapidly, only to show a minor decrease afterwards. Equilibrium data were fitted to Freundlich models to determine the water-hard coal partitioning coefficient. Physical adsorption caused by properties of the compounds was the predominant mechanism in the removal process.

  5. Coupling of Algal Biofuel Production with Wastewater

    Directory of Open Access Journals (Sweden)

    Neha Chamoli Bhatt

    2014-01-01

    Full Text Available Microalgae have gained enormous consideration from scientific community worldwide emerging as a viable feedstock for a renewable energy source virtually being carbon neutral, high lipid content, and comparatively more advantageous to other sources of biofuels. Although microalgae are seen as a valuable source in majority part of the world for production of biofuels and bioproducts, still they are unable to accomplish sustainable large-scale algal biofuel production. Wastewater has organic and inorganic supplements required for algal growth. The coupling of microalgae with wastewater is an effective way of waste remediation and a cost-effective microalgal biofuel production. In this review article, we will primarily discuss the possibilities and current scenario regarding coupling of microalgal cultivation with biofuel production emphasizing recent progress in this area.

  6. Treatment of Mineral Oil Refinery Wastewater in Microbial Fuel Cells Using Ionic Liquid Based Separators

    Directory of Open Access Journals (Sweden)

    Hasna Addi

    2018-03-01

    Full Text Available Microbial fuel cells (MFCs are an environmentally friendly technology that can recover electricity directly from several wastes at ambient temperatures. This work explores the use of mineral oil refinery wastewater as feedstock in single-chamber air-cathode MFC devices. A polymer inclusion membrane based on the ionic liquid methyltrioctylammonium chloride, [MTOA+][Cl−], at a concentration of 70% w/w, was used as separator, showing a good efficiency in power production and chemical oxygen demand (COD removal. The power and the chemical oxygen demand removal reached values of 45 mW/m3 and over 80%, respectively. The evolution of other parameters of the wastewater including nitrites, phosphates and sulphates were also studied. Kjeldahl nitrogen and sulphates were significantly reduced during MFC operation. The results show that mineral oil refinery wastewater can be used as feedstock in air breathing cathode-microbial fuel cells based on polymer ionic liquid inclusion membranes. This configuration could represent a good alternative for wastewater depuration while producing energy during the process.

  7. Oil production system

    Energy Technology Data Exchange (ETDEWEB)

    Ballantyne, J F

    1983-12-21

    A new oil producing system is proposed which consists of a group of underwater wells, an underwater riser and a floating storage facility for the production of the wells. The group of wells and the riser are interconnected through a manifold system in such a way that the production from any well or from the entire group of wells go to the base (foundation) of the riser. From above the riser is connected with the floating storage facility which is equipped, besides tanks for storing the well products, with a separation device for separating the oil and the accompanying gas. The gas is used as a fuel for producing electric power required by the dynamic positioning systems. The products from each well are tested by means of a regulable coupling controlled by means of a cable, which is passed from the surface through the riser. The wellhead equipment for the unslanted wells is mounted on a template previously installed on the sea floor. From the template the well products enter the riser through the manifold unit system.

  8. Production and morphological components of sunflower on soil fertilized with cassava wastewater

    Directory of Open Access Journals (Sweden)

    Mara Suyane Marques Dantas

    Full Text Available ABSTRACT Agroindustrial residues, such as cassava wastewater, have been used as soil fertilizers, reducing environmental pollution and recovering nutrients. The objective of this work was to evaluate production and morphological components and oil yield of sunflower (Helianthus annuus, hybrid Helio-250, fertilized with cassava wastewater. The experiment was conducted at the Experimental Station of the Instituto Agronomico de Pernambuco, Vitória de Santo Antão, State of Pernambuco, Brazil. A randomized block experimental design was used, with six cassava wastewater rates (0, 8.5, 17.0, 34.0, 68.0 and 136 m3 ha-1 and four replications. The variables evaluated were shoot fresh and dry weight, capitulum fresh and dry weight, capitulum diameter, seed yield, oil yield and seed oil content. The use cassava wastewater as soil fertilizer improved the production and morphological variables evaluated, except the seed oil content, which decreased with application of cassava wastewater rates above 25 m3 ha-1.

  9. Whither Alberta's oil production?

    International Nuclear Information System (INIS)

    Purvis, R.A.; Dick, A.B.

    1991-01-01

    It is demonstrated how a combination of old theory (decline methods and statistics) and new technology (computer graphics) can enhance decline-curve forecasts for multi-well groupings. Production and well-count forecasts are presented for four different sized groups of aggregate production. The four examples are: the small Manville pool; the Pembina Cardium, Alberta's largest oil pool; an aggregate of all reef pools of Keg River age; and an aggregate of all wells reporting conventional oil production in the province of Alberta. In each case graphical results show the historical and forecast trends for the statistical distribution of well rates, the median well rate, the aggregated rate, and the number of producing wells. It is concluded that well rate distributions for groups ranging from 15 wells in a single pool to thousands of wells in hundreds of pools are all approximately lognormal. Lognormal well rate distributions and Lorenz graphs provide qualitative and quantitative assessments of a resource base. Decline curves for the median well rate can reveal trends masked in the aggregated rate by changing well count, operating practice and degradation of the resource base. The number of producing wells in Alberta has grown from ca 9000 in 1970 to ca 24,000 in 1988, has remained constant from 1988-1990, and will start to decline as the number of suspended or abandoned wells exceeds the number of new completions. 3 refs., 13 figs., 4 figs

  10. Study of Wastewaters Contaminated with Heavy Metals in Bioethanol Production

    Science.gov (United States)

    Bartošová, Alica; Blinová, Lenka

    2017-06-01

    Bioethanol as a substitute for traditional sources of energy, especially oil transport, is currently one of the most researched alternative motor fuels. Normally, bioethanol is produced from agricultural crops such as sugar cane or corn. However, this is counter-productive, because agriculture is primarily serving to ensure enough food for the people. It is therefore necessary to look for new production of appropriate non-food crops or find an added value to this process. Utilisation of contaminated water from metal industry could be one of them. Based on the hypothesis of reduction of some toxic metals with higher oxidation number is opening the possibility of using this wastewater in alcohol fermentation of any kind of biomass. In this study, hexavalent chromium Cr(VI) was used as a model contaminant in the process of aerobic fermentation of corn to bioethanol. To determine the reduction potential of glucose to Cr(VI), and to quantitatively determinate the glucose content after saccharification, UV/VIS spectrophotometry was used. As a method of qualitative determination of fermentation product, gas chromatography with mass detection was used. Infrared spectrometry was used for qualitative analyses of produced ethanol. Based on the established results shown in this paper, we can conclude that the presence of hexavalent chromium in the fermentation process does not have a significant negative impact, while offering the opportunity of using the industrial wastewaters for the production of bioethanol fuel.

  11. Study of Wastewaters Contaminated with Heavy Metals in Bioethanol Production

    Directory of Open Access Journals (Sweden)

    Bartošová Alica

    2017-06-01

    Full Text Available Bioethanol as a substitute for traditional sources of energy, especially oil transport, is currently one of the most researched alternative motor fuels. Normally, bioethanol is produced from agricultural crops such as sugar cane or corn. However, this is counter-productive, because agriculture is primarily serving to ensure enough food for the people. It is therefore necessary to look for new production of appropriate non-food crops or find an added value to this process. Utilisation of contaminated water from metal industry could be one of them. Based on the hypothesis of reduction of some toxic metals with higher oxidation number is opening the possibility of using this wastewater in alcohol fermentation of any kind of biomass. In this study, hexavalent chromium Cr(VI was used as a model contaminant in the process of aerobic fermentation of corn to bioethanol. To determine the reduction potential of glucose to Cr(VI, and to quantitatively determinate the glucose content after saccharification, UV/VIS spectrophotometry was used. As a method of qualitative determination of fermentation product, gas chromatography with mass detection was used. Infrared spectrometry was used for qualitative analyses of produced ethanol. Based on the established results shown in this paper, we can conclude that the presence of hexavalent chromium in the fermentation process does not have a significant negative impact, while offering the opportunity of using the industrial wastewaters for the production of bioethanol fuel.

  12. Online sensing and control of oil in process wastewater

    Science.gov (United States)

    Khomchenko, Irina B.; Soukhomlinoff, Alexander D.; Mitchell, T. F.; Selenow, Alexander E.

    2002-02-01

    Industrial processes, which eliminate high concentration of oil in their waste stream, find it extremely difficult to measure and control the water purification process. Most oil separation processes involve chemical separation using highly corrosive caustics, acids, surfactants, and emulsifiers. Included in the output of this chemical treatment process are highly adhesive tar-like globules, emulsified and surface oils, and other emulsified chemicals, in addition to suspended solids. The level of oil/hydrocarbons concentration in the wastewater process may fluctuate from 1 ppm to 10,000 ppm, depending upon the specifications of the industry and level of water quality control. The authors have developed a sensing technology, which provides the accuracy of scatter/absorption sensing in a contactless environment by combining these methodologies with reflective measurement. The sensitivity of the sensor may be modified by changing the fluid level control in the flow cell, allowing for a broad range of accurate measurement from 1 ppm to 10,000 ppm. Because this sensing system has been designed to work in a highly invasive environment, it can be placed close to the process source to allow for accurate real time measurement and control.

  13. MBBR evaluation for oil refinery wastewater treatment, with post-ozonation and BAC, for wastewater reuse.

    Science.gov (United States)

    Schneider, E E; Cerqueira, A C F P; Dezotti, M

    2011-01-01

    This work evaluated the performance of a Moving Bed Biofilm Reactor (MBBR) in the treatment of an oil refinery wastewater. Also, it investigated the possibility of reuse of the MBBR effluent, after ozonation in series with a biological activated carbon (BAC) column. The best performance of the MBBR was achieved with a hydraulic retention time (HRT) of 6 hours, employing a bed to bioreactor volume ratio (V(B)/V(R)) of 0.6. COD and N-NH₄(+) MBBR effluent concentrations ranged from 40 to 75 mg L⁻¹ (removal efficiency of 69-89%) and 2 to 6 mg L⁻¹ (removal efficiency of 45-86%), respectively. Ozonation carried out for 15 min with an ozone concentration of 5 mg L⁻¹ was able to improve the treated wastewater biodegradability. The treatment performance of the BAC columns was practically the same for ozonated and non ozonated MBBR effluents. The dissolved organic carbon (DOC) content of the columns of the activated carbon columns (CAG) was in the range of 2.1-3.8 mg L⁻¹, and the corresponding DOC removal efficiencies were comprised between 52 and 75%. The effluent obtained at the end of the proposed treatment presented a quality, which meet the requirements for water reuse in the oil refinery.

  14. Analysing oil-production subsidies

    Science.gov (United States)

    Steenblik, Ronald

    2017-11-01

    Understanding how subsidies affect fossil-fuel investment returns and production is crucial to commencing new reforms. New analysis on the impact of subsidies on US crude-oil producers finds that, at recent oil prices of around US50 per barrel, tax preferences and other subsidies push nearly half of new oil investments into profitability.

  15. Bioremediation of wastewater from edible oil refinery factory using oleaginous microalga Desmodesmus sp. S1.

    Science.gov (United States)

    Mar, Cho Cho; Fan, Yong; Li, Fu-Li; Hu, Guang-Rong

    2016-12-01

    Edible oil industry produced massive wastewater, which requires extensive treatment to remove pungent smell, high phosphate, carbon oxygen demand (COD), and metal ions prior to discharge. Traditional anaerobic and aerobic digestion could mainly reduce COD of the wastewater from oil refinery factories (WEORF). In this study, a robust oleaginous microalga Desmodesmus sp. S1 was adapted to grow in WEORF. The biomass and lipid content of Desmodesmus sp. S1 cultivated in the WEORF supplemented with sodium nitrate were 5.62 g·L(-1) and 14.49%, whereas those in the WEORF without adding nitrate were 2.98 g·L(-1) and 21.95%. More than 82% of the COD and 53% of total phosphorous were removed by Desmodesmus sp. S1. In addition, metal ions, including ferric, aluminum, manganese and zinc were also diminished significantly in the WEORF after microalgal growth, and pungent smell vanished as well. In comparison with the cells grown in BG-11 medium, the cilia-like bulges and wrinkles on the cell surface of Desmodesmus sp. S1 grown in WEORF became out of order, and more polyunsaturated fatty acids were detected due to stress derived from the wastewater. The study suggests that growing microalgae in WEORF can be applied for the dual roles of nutrient removal and biofuel feedstock production.

  16. Long term prediction of unconventional oil production

    International Nuclear Information System (INIS)

    Mohr, S.H.; Evans, G.M.

    2010-01-01

    Although considerable discussion surrounds unconventional oil's ability to mitigate the effects of peaking conventional oil production, very few models of unconventional oil production exist. The aim of this article was to project unconventional oil production to determine how significant its production may be. Two models were developed to predict the unconventional oil production, one model for in situ production and the other for mining the resources. Unconventional oil production is anticipated to reach between 18 and 32 Gb/y (49-88 Mb/d) in 2076-2084, before declining. If conventional oil production is at peak production then projected unconventional oil production cannot mitigate peaking of conventional oil alone.

  17. Antioxidant activity of olive oil mill wastewater obtained from different thermal treatments

    Directory of Open Access Journals (Sweden)

    Giuffrè, A. M.

    2012-06-01

    Full Text Available In food industry, Olive Oil Mill Wastewater (OOMWW is considered a by-product because of the presence of biostatic compounds with a high polluting rate, in particular phenols. Moreover, during olive oil processing, a large amount of this by-product constitutes an ecological and economical problem for the producers. To reevaluate this by-product, the reuse of this wastewater to obtain useful compounds appears to be very important. In order to purify the wastewater, the development of operations that modify its organic content seems necessary for obtaining of eventual fertilizing agents and/or to recover substances with a high added value such as phenolic compounds, which are currently recognized scientifically as molecules with a high antioxidant activity. A chromatographic analysis of these compounds was conducted to characterize different concentrations of wastewater and the reducing power of the extracts was measured. The thermal treatment of olive oil mill wastewater in a rotary evaporator and in an oven involved an increase in radical scavenging efficiency. These results could be correlated with the possibility of recovering and reusing this type of waste for its antioxidant properties.

    En la industria alimentaria, el alpechín se considera un subproducto debido a la presencia de compuestos bioestáticos, con una alta tasa de contaminación, particularmente los fenoles. Además, durante el procesado de la aceituna, la generación de una gran cantidad de este subproducto supone un problema ecológico y económico para los productores. Es importante la reutilización de este agua de desecho para obtener compuestos útiles. Para purificar el agua de desecho es necesario el desarrollo de operaciones que modifiquen su contenido orgánico, para poder obtener agentes fertilizantes y/o recuperar sustancias con un alto valor añadido como los compuestos fenólicos, que actualmente están reconocidos científicamente como moléculas con una

  18. Influence of temperature on hydrogen production from bread mill wastewater by sewage sludge

    Energy Technology Data Exchange (ETDEWEB)

    Tang, G.L.; Huang, J.; Li, Y.Y.; Sun, Z.J. [China Agricultural Univ., Beijing (China). College of Resources and Environmental Sciences; Tang, Q.Q. [Nanjing Univ., Nanjing (China). Medical School

    2008-07-01

    Hydrogen (H{sub 2}) energy has been touted as a sustainable and clean energy source that can solve environmental problems such as acid rain, greenhouse gases and transboundary pollution. While most hydrogen is currently produced from nonrenewable sources such as oil, natural gas, and coal, these processes are energy-intensive and costly. The biological production of hydrogen using fermentative bacteria is an environmentally friendly and energy-saving process which has recently attracted much attention as an effective way of converting biomass into H{sub 2}. Waste-based H{sub 2} production processes mainly include wastewater from paper mills, municipal solid waste, rice winery wastewater, and food wastewater from cafeterias. This study investigated the use of bread mill wastewater for biological production of hydrogen due to its high production potential. Annual bread production in China is estimated to be over 1.5 million tons, producing 10 m{sup 3} of wastewater per ton of bread. The wastewater has high chemical oxygen demand and carbohydrate concentrations and is therefore suitable for anaerobic treatment processes. This study evaluated the effect of temperature on H{sub 2} production from bread mill wastewater by sewage sludge in lab-scale experiments. H{sub 2} production, the distribution of volatile fatty acids and the lag-phase time were influenced by temperature. H{sub 2} production and H{sub 2} yield increased with increasing temperature. The optimal temperature for H{sub 2} production was 50 degrees C. Butyrate, acetate and alcohol were the main by-products of H{sub 2} fermentation. According to 16S rDNA analysis, the dominant microflora was Clostridium, but the microbial species varied with temperature. The activation energy for H{sub 2} production was estimated to be 92 kJ per mol for bread mill wastewater. It was concluded that bread mill wastewater could potentially serve as a substrate for H{sub 2} production. This research provides a means of

  19. Seed production for fuel oils

    International Nuclear Information System (INIS)

    Mosca, G.

    1992-01-01

    With the aim of assessing commercialization prospects for vegetable oils to be used as diesel fuel alternatives, this paper provides maps indicating regional production quantities for soybean, rape and sunflower seeds in Italy. It then tables and discusses the results of energy input-output analyses carried out for rape and soybean oil production

  20. Study on Olive Oil Wastewater Treatment: Nanotechnology Impact

    Directory of Open Access Journals (Sweden)

    Nika Gholamzadeh

    2016-11-01

    Full Text Available The olive mill wastewater (OMW is generated from olive oil extraction in olive mills. It contains a very high organic load and considerable quantities of phytotoxicity compounds. Comprehensive articles with different methods have been published about the treatment of OMW. This paper reviews the recent reports on the variety methods of OMW treatment. Biological process, containing aerobic pre-treatment by using different cultures and anaerobic co-digestion with other sewage and also added external nutrient with optimum ratio attracted much attention in the treatment of OMW. However, advanced oxidation process (AOP due to the high oxidation potential which causes destruction of organic pollutants, toxic and chlorinated compounds have been considered. Furthermore, membrane technologies consist of microfiltration, ultrafiltration and especially nanofiltrationin wastewater treatment are growing in recent years. They offer high efficiency and mediocre investments owing to novel membrane materials, membrane design technics, module figures and improvement of the skills. In addition, fouling reduces the membrane performances in time, which is a main problem of cost efficiency.

  1. Environmental emergency in the oil production and oil products transport

    Directory of Open Access Journals (Sweden)

    Jozef Čopan

    2006-10-01

    Full Text Available The paper refers to the experience of the environmental emergency response in the case of accidental leakages of oil or oil products into the environment. The gained experience is demonstrated on four different sites where the remediation of contaminated soil / groundwater and emergency response were carried out by the Czech environmental company DEKONTA a.s.

  2. Dual application of duckweed and azolla plants for wastewater treatment and renewable fuels and petrochemicals production

    Science.gov (United States)

    2014-01-01

    Background Shortages in fresh water supplies today affects more than 1 billion people worldwide. Phytoremediation strategies, based on the abilities of aquatic plants to recycle nutrients offer an attractive solution for the bioremediation of water pollution and represents one of the most globally researched issues. The subsequent application of the biomass from the remediation for the production of fuels and petrochemicals offers an ecologically friendly and cost-effective solution for water pollution problems and production of value-added products. Results In this paper, the feasibility of the dual application of duckweed and azolla aquatic plants for wastewater treatment and production of renewable fuels and petrochemicals is explored. The differences in absorption rates of the key wastewater nutrients, ammonium and phosphorus by these aquatic macrophytes were used as the basis for optimization of the composition of wastewater effluents. Analysis of pyrolysis products showed that azolla and algae produce a similar range of bio-oils that contain a large spectrum of petrochemicals including straight-chain C10-C21 alkanes, which can be directly used as diesel fuel supplement, or a glycerin-free component of biodiesel. Pyrolysis of duckweed produces a different range of bio-oil components that can potentially be used for the production of “green” gasoline and diesel fuel using existing techniques, such as catalytic hydrodeoxygenation. Conclusions Differences in absorption rates of the key wastewater nutrients, ammonium and phosphorus by different aquatic macrophytes can be used for optimization of composition of wastewater effluents. The generated data suggest that the composition of the petrochemicals can be modified in a targeted fashion, not only by using different species, but also by changing the source plants’ metabolic profile, by exposing them to different abiotic or biotic stresses. This study presents an attractive, ecologically friendly and cost

  3. Dual application of duckweed and azolla plants for wastewater treatment and renewable fuels and petrochemicals production.

    Science.gov (United States)

    Muradov, Nazim; Taha, Mohamed; Miranda, Ana F; Kadali, Krishna; Gujar, Amit; Rochfort, Simone; Stevenson, Trevor; Ball, Andrew S; Mouradov, Aidyn

    2014-02-28

    Shortages in fresh water supplies today affects more than 1 billion people worldwide. Phytoremediation strategies, based on the abilities of aquatic plants to recycle nutrients offer an attractive solution for the bioremediation of water pollution and represents one of the most globally researched issues. The subsequent application of the biomass from the remediation for the production of fuels and petrochemicals offers an ecologically friendly and cost-effective solution for water pollution problems and production of value-added products. In this paper, the feasibility of the dual application of duckweed and azolla aquatic plants for wastewater treatment and production of renewable fuels and petrochemicals is explored. The differences in absorption rates of the key wastewater nutrients, ammonium and phosphorus by these aquatic macrophytes were used as the basis for optimization of the composition of wastewater effluents. Analysis of pyrolysis products showed that azolla and algae produce a similar range of bio-oils that contain a large spectrum of petrochemicals including straight-chain C10-C21 alkanes, which can be directly used as diesel fuel supplement, or a glycerin-free component of biodiesel. Pyrolysis of duckweed produces a different range of bio-oil components that can potentially be used for the production of "green" gasoline and diesel fuel using existing techniques, such as catalytic hydrodeoxygenation. Differences in absorption rates of the key wastewater nutrients, ammonium and phosphorus by different aquatic macrophytes can be used for optimization of composition of wastewater effluents. The generated data suggest that the composition of the petrochemicals can be modified in a targeted fashion, not only by using different species, but also by changing the source plants' metabolic profile, by exposing them to different abiotic or biotic stresses. This study presents an attractive, ecologically friendly and cost-effective solution for efficient bio

  4. Economics of Russian oil production

    International Nuclear Information System (INIS)

    Gubenko, I.

    1993-01-01

    The main technical indicators of oil production in Russia are presented from the year 1988, when the current decline in oil production started. In 1992, only 9 new oil deposits were put into production, and average well productivity dropped to 12.4 tonnes/d. The number of idle wells reached 31,934 as compared to 8,714 in 1988. The share of low productivity deposits in 1993 was 49.7%. In the first five months of 1993, the number of new wells put into operation failed to offset the shutdown of old wells. Although the number of workovers grew by 32%, this work was insufficient to stabilize oil production. The decline in production is due to the general state of economic stability and endless reorganizations in the economy, and to the lack of sufficient investment in the industry. Oil-producing enterprises have lacked funds due to systematic and growing indebtedness of buyers of crude. This overdue indebtedness reached 393 billion rubles by the beginning of 1993. Although domestic oil prices increased sharply in 1991-92, the volume of production in real terms has dropped by nearly a third. Oil is sold at different prices to different categories of buyers. Prices include expenses, profit from which a 32% profits tax is paid, excise taxes, and payments to a centralized price-regulation fund. From the industry point of view, certain reforms are necessary to reconstruct and develop the industry. These include ensuring payments to oil producers, gradual transfer of Russian prices to world levels, lowering taxes, and adoption and refinement of a law on oil. 1 fig., 7 tabs

  5. Semipermeable membrane devices concentrate mixed function oxygenase inducers from oil sands and refinery wastewaters

    International Nuclear Information System (INIS)

    Parrott, J.L.; Hewitt, L.M.

    2002-01-01

    The health of fish in the Athabasca River was examined to determine the effects of both natural and anthropogenic oil sands exposure on liver mixed function oxygenase (MFO) enzymes. Semipermeable membrane devices (SPMD) were used to concentrate bioavailable compounds that may result in MFO induction. The SPMDs were used for a period of 2 weeks in the Steepbank River as well as in oil refinery wastewater and intake ponds. They were then tested to see if they induced ethoxyresorufin-O-deethylase (EROD) activity in hepatoma cells, a cell line derived from a liver cancer of a small fish. SPMDs from the wastewater pond contained potent EROD inducers in fish liver cells. SPMDs from the Athabasca River exhibited some EROD inducers, but they were 1/100 as potent as those of the refinery wastewater. The characteristics of MFO inducers from refinery wastewater were different from natural inducers from the oil sands in the Athabasca and Steepbank Rivers. For instance, log Kow was less than 5 for refinery wastewater, but it was greater than 5 for Athabasca River wastewater and from natural oil sands exposure. In the case of the Steepbank River, the pattern of MFO induction was similar to the MFO induction seen in wild fish.The highest MFO inducers were found to be in the area of the mine, suggesting and anthropogenic pollution source. The less potent inducers were in the area of the natural and undisturbed oil sands. Very few inducers were found outside of the oil sands formation

  6. Oil refinery wastewater treatment using physicochemical, Fenton and Photo-Fenton oxidation processes.

    Science.gov (United States)

    Tony, Maha A; Purcell, Patrick J; Zhao, Yaqian

    2012-01-01

    The objective of this study was to investigate the application of advanced oxidation processes (AOPs) to the treatment of wastewaters contaminated with hydrocarbon oil. Three different oil-contaminated wastewaters were examined and compared: (i) a 'real' hydrocarbon wastewater collected from an oil refinery (Conoco-Phillips Whitegate refinery, County Cork, Ireland); (ii) a 'real' hydrocarbon wastewater collected from a car-wash facility located at a petroleum filling station; and (iii) a 'synthetic' hydrocarbon wastewater generated by emulsifying diesel oil and water. The AOPs investigated were Fe(2+)/H(2)O(2) (Fenton's reagent), Fe(2+)/H(2)O(2)/UV (Photo-Fenton's reagent) which may be used as an alternative to, or in conjunction with, conventional treatment techniques. Laboratory-scale batch and continuous-flow experiments were undertaken. The photo-Fenton parametric concentrations to maximize COD removal were optimized: pH = 3, H(2)O(2) = 400 mg/L, and Fe(2+) = 40 mg/L. In the case of the oil-refinery wastewater, photo-Fenton treatment achieved approximately 50% COD removal and, when preceded by physicochemical treatment, the percentage removal increased to approximately 75%.

  7. World resources of oil products

    International Nuclear Information System (INIS)

    Bonnaterre, Raymond

    2014-01-01

    In a first part, the author outlines that the issue of density of an oil product raises the question of the validity of a counting approach based on volumes. As oil industries produce always less heavy products and always more light products, this means that always less oil is needed to produce a gallon or a litre of fuel out of a refinery. The author comments the evolution of crude oil extraction. In a second part, he outlines that hydrocarbon productions become always more complex with respect to their origin. Thus, during gas extraction, humid gases are recovered which contain an important part of hydrocarbons similar to light oil. These aspects and the development of shale gas exploitation will make the USA the first oil producer in the world whereas they still have to import heavy oil to feed their refineries. He discusses the level of reserves and production costs with respect to the product type or its extraction location. He discusses the evolution of the estimates of world ultimately recoverable resources (synthesis processes excluded). He comments the level of condensate extraction ratio of the main shale gas fields in the USA and outlines the cost of natural gas imports for France. He outlines the importance of GTL (gas to liquid) processes, the increasing importance of bio-fuels (notably isobutanol biosynthesis and terpene biosynthesis). In the third part, the author states that the barrel price should keep on increasing and, in the fourth part, proposes a list of issues which will impact the future of the oil market

  8. Screening of thermotolerant microorganisms and application for oil separation from palm oil mill wastewater

    Directory of Open Access Journals (Sweden)

    Aran H-Kittikun

    2007-05-01

    Full Text Available The characteristics of palm oil mill wastewater (POMW were brown color, pH 3.8-4.3, temperature 48-55oC, total solids 68.2-82.1 g/l, suspended solids 26.2-65.6 g/l, oil and grease 19.1-25.1 g/l, COD 49.9-160.7g/l and BOD 32.5-75.3 g/l. After centrifugation (3,184 xg of 50 ml POMW for 10 min, the POMW was separated into 3 layers: top (oil, middle (supernatant and bottom layer (sediment. The sediment containeddry weight 1.19 g and oil and grease 1.07 g. In order to release oil and grease trapped in palm fiber debris in the POMW, cellulase- and/or xylanase-enzyme-producing and thermotolerant microorganisms wereisolated. The isolates SO1 and SO2 were isolated from soil near the first anaerobic pond of the palm oil mill. They were aerobic, Gram positive, rod shaped, thermotolerant microorganisms and produced cellulase 12.11 U/ml (3 days and 7.2 U/ml (4 days, and xylanase 50.98 U/ml (4 days and 20.42 U/ml (4 days, respectivelyin synthetic medium containing carboxymethycellulose as a carbon source. When these 2 isolates were added into the steriled POMW under shaking condition for 7 days, after centrifugation at 3,184 xg the isolate SO1gave the better % reduction of dry weight (64.66 % and of oil and grease in the bottom layer (85.32 % of the POMW.

  9. Electrochemical removal of phenol from oil refinery wastewater.

    Science.gov (United States)

    Abdelwahab, O; Amin, N K; El-Ashtoukhy, E-S Z

    2009-04-30

    This study explores the possibility of using electrocoagulation to remove phenol from oil refinery waste effluent using a cell with horizontally oriented aluminum cathode and a horizontal aluminum screen anode. The removal of phenol was investigated in terms of various parameters namely: pH, operating time, current density, initial phenol concentration and addition of NaCl. Removal of phenol during electrocoagulation was due to combined effect of sweep coagulation and adsorption. The results showed that, at high current density and solution pH 7, remarkable removal of 97% of phenol after 2h can be achieved. The rate of electrocoagulation was observed to increase as the phenol concentration decreases; the maximum removal rate was attained at 30 mg L(-1) phenol concentration. For a given current density using an array of closely packed Al screens as anode was found to be more effective than single screen anode, the percentage phenol removal was found to increase with increasing the number of screens per array. After 2h of electrocoagulation, 94.5% of initial phenol concentration was removed from the petroleum refinery wastewater. Energy consumption and aluminum Electrode consumption were calculated per gram of phenol removed. The present study shows that, electrocoagulation of phenol using aluminum electrodes is a promising process.

  10. Efficacies of Various Anaerobic Starter Seeds for Biogas Production from Different Types of Wastewater

    Directory of Open Access Journals (Sweden)

    Pawinee Chaiprasert

    2017-01-01

    Full Text Available Various anaerobic starter seeds from different sources were investigated for their efficacies in treatment of different types of wastewater. Six combinations of starter seeds and wastewaters were selected out of 25 combination batch experiments and operated in semicontinuous reactors. It was noticed that the efficacies of various anaerobic starter seeds for biogas production from different types of wastewater in terms of reactor performance and stability were depended on wastewater characteristics and F/M ratio affecting microbial community and their microbial activities. However, exogenous starter seed can be used across different types of wastewater with or without acclimatization. Four reactors reached the targeted OLR of 2 kg COD/m3·d with high performance and stability except for concentrated rubber wastewater (RBw, even using high active starter seeds of cassava starch (CSs and palm oil (POs. The toxic compounds in RBw such as ammonia and sulfate might also adversely affect methanogenic activity in CSsRBw and POsRBw reactors. DGGE analysis showed that propionate utilizers, Smithella propionica strain LYP and Syntrophus sp., were detected in all samples. For Archaea domain, methylotrophic, hydrogenotrophic, and acetoclastic methanogens were also detected. Syntrophic relationships were assumed between propionate utilizers and methanogens as acetate/H2 producers and utilizers, respectively.

  11. Antioxidant activity of oregano, parsley, and olive mill wastewaters in bulk oils and oil-in-water emulsions enriched in fish oil.

    Science.gov (United States)

    Jimenez-Alvarez, D; Giuffrida, F; Golay, P A; Cotting, C; Lardeau, A; Keely, Brendan J

    2008-08-27

    The antioxidant activity of oregano, parsley, olive mill wastewaters (OMWW), Trolox, and ethylenediaminetetraacetic acid (EDTA) was evaluated in bulk oils and oil-in-water (o/w) emulsions enriched with 5% tuna oil by monitoring the formation of hydroperoxides, hexanal, and t-t-2,4-heptadienal in samples stored at 37 degrees C for 14 days. In bulk oil, the order of antioxidant activity was, in decreasing order (p oregano > parsley > EDTA > Trolox. The antioxidant activity in o/w emulsion followed the same order except that EDTA was as efficient an antioxidant as OMWW. In addition, the total phenolic content, the radical scavenging properties, the reducing capacity, and the iron chelating activity of OMWW, parsley, and oregano extracts were determined by the Folin-Ciocalteau, oxygen radical absorbance capacity, ferric reducing antioxidant power, and iron(II) chelating activity assays, respectively. The antioxidant activity of OMWW, parsley, and oregano in food systems was related to their total phenolic content and radical scavenging capacity but not to their ability to chelate iron in vitro. OMWW was identified as a promising source of antioxidants to retard lipid oxidation in fish oil-enriched food products.

  12. WATER PINCH TECHNOLOGY APPLICATION TO MINIMIZE SULPHUROUS WASTEWATER IN AN OIL REFINERY

    Directory of Open Access Journals (Sweden)

    Gabriel Orlando Lobelles Sardiñas

    2017-01-01

    Full Text Available In oil refining industries there is a high water consumption, which influences the high production costs and impacts the environment due to the discharge of their wastes. It is known that there are no technological conditions for the reuse of industrial water at the oil refineries, based on hydroskimming processes. The objective of this study is to implement the process integration methodology, Water Pinch, to a sour water stripper unit, as a unitary process of an oil refinery, to minimize the amount of sulphurous waste water and reduce contamination of the bay that receives these wastes. The technology is applied to evaluate the volume of sulphurous wastewater generated in the Cienfuegos oil refinery. This technology allows identifying opportunities for recovery and reuse of water, based on concentration ranges of contaminants. To achieve this purpose, a sour water stripper tower was assessed with the help of Water Pinch software, which provided an optimized distribution network, as a proposed technological improvement. This facilitated to recover and reuse 667 757, 28 m3 of water per year, and 1 035 023, 78 CUC were saved, at the same time the amount of polluting effluents decreased in approximately 2 % of non-reusable treated water.

  13. 40 CFR 63.137 - Process wastewater provisions-oil-water separators.

    Science.gov (United States)

    2010-07-01

    ... wastewater provisions—oil-water separators. (a) For each oil-water separator that receives, manages, or...; (2) A floating roof meeting the requirements in 40 CFR part 60, subpart QQQ § 60.693-2 (a)(1)(i), (a... to construct and operate a floating roof, such as over the weir mechanism, the owner or operator...

  14. European oil product supply modelling

    International Nuclear Information System (INIS)

    Saint-Antonin, V.

    1998-01-01

    Over the last few years, trends in European oil product consumption (in terms of level as structure and quality) has important implications of the refining industry. In this context, the purpose of this thesis consists in building a mathematical programming model applied to the European refineries in order to determine oil product supply prices, European refining industry investments and oil product exchanges of the European Union. The first part presents the reason for our choice for a long-term aggregate multi-refineries linear programming model, based on European refineries characteristics and the objectives of our model. Its dual properties are studied in detail and we focus particularly on the European exchange modelling. In the second part, an analysis of the European refining trends leads us to identify parameters and variables of the model that are essential to the aggregate representation of the European oil product supply. The third part is devoted to the use of this model, regarding two scenarios of increasingly stringent specifications for gasoline and diesel oil. Our interest for these products is due to their important share of the European oil product consumption and the not insignificant responsibility of the transport sector for atmospheric pollution. Finally, in order to have the use of an overall picture of the European refining industry, we build a regression model summarizing, though a few equations, the main relations between the major endogenous and exogenous variables o the LP model. Based on pseudo-data, this kind of model provides a simple and robust representation of the oil product supply. But a more specialized analysis of the refining industry operations, turning on a technical assessment of processing units, is reliant on the use of an optimization model such as the model we have built. (author)

  15. Natural cold pressed oils as cosmetic products

    Directory of Open Access Journals (Sweden)

    Małgorzata Ligęza

    2016-12-01

    Full Text Available Background. It seems that patients may ask general practitioners about natural cosmetics applied on the skin regarding their safety and suitability. Objectives. The aim of the study was to analyze natural cold pressed oils as potential cosmetic products. Material and methods. Cold pressed oils obtained from selected seeds and fruit stones were analyzed, including: chokeberry seed oil, blackcurrant seed oil, elderberry seed oil, raspberry seed oil, apricot seed oil, tomato seed oil, strawberry seed oil, broccoli seed oil, Nigella sativa seed oil, hemp oil, safflower seed oil, Silybum marianum seed oil and coconut oil. 80 adult volunteers assessed the cosmetic properties of the analyzed oils. Each of the volunteers tested 2 to 4 different oils, by applying them on the skin. In addition, patch tests with all analyzed oils were performed on 23 individuals. Results. The majority of tested oils were positively evaluated by the participants: in the opinion of the participants, oil extracted from safflower had the best appearance (100% positive opinions, coconut oil had the best smell (70% positive opinions, while black currant seed oil showed the best absorbency (85% positive opinions. No irritation was observed within the analyzed product group, albeit one allergic reaction to apricot seed oil was observed with patch testing. Conclusions . Based on the achieved results, it could be suggested that natural cold pressed oils can be applied to the skin as cosmetics. Our observations may be helpful for general practitioners when choosing natural cosmetics.

  16. Removal of oil and grease from automobile garage wastewater using electrocoagulation

    Science.gov (United States)

    Manilal, A. M.; Harinarayanan Nampoothiri, M. G.; Soloman, P. A.

    2017-06-01

    Wastewater from automobile garages and workshops is an important contributor to the water pollution. Oil and grease is one of the major content of wastewater from vehicle garages. Wastewater from a public transport depot at Thrissur district in Kerala, India was collected for the study. A batch reactor has been devised to assess the efficacy of electrocoagulation in removing oil and grease from the wastewater. Aluminium and iron were tested as the anode material with stainless steel as cathode. Experiments were conducted to investigate the effect of various operating parameters such as current density, pH, time and salt concentration on oil and grease removal. The results shown that aluminium is superior to iron in removing the oil and grease from the wastewater. The reactor with aluminium as anode was able to remove 90.8 % of the oil and grease at a current density of 0.6 A/dm2 in 15 minutes. The calculated specific energy consumption is also less for aluminium in comparison with iron.

  17. Green synthesis of palm oil mill effluent-based graphenic adsorbent for the treatment of dye-contaminated wastewater.

    Science.gov (United States)

    Teow, Yeit Haan; Nordin, Nadzirah Ilyiani; Mohammad, Abdul Wahab

    2018-05-12

    Textile wastewater contains methylene blue (MB), a major coloring agent in textile industry. Activated carbon (AC) is the most widely used adsorbent in removing dyes from industrial wastewater. However, high production cost of AC is the major obstacle for its wide application in dye wastewater treatment. In this study, a sustainable approach in synthesizing graphenic adsorbent from palm oil mill effluent (POME), a potential carbonaceous source, has been explored. This new development in adsorption technique is considered as green synthesis as it does not require any binder during the synthesis process, and at the same time, it helps to solve the bottleneck of palm oil industry as POME is the main cause contributed to Malaysia's water pollution problem. The synthesized GSC was characterized through XRD, FESEM, and EDX. The adsorption performance of the synthesized GSC was evaluated by adsorption of MB. The effect of initial concentration of synthetic MB solution (1-20 mg/L) and weight of GSC (5-20 g) were investigated. A remarkable change in color of synthetic MB solution from blue to crystal clear was observed at the end of adsorption study. High efficiency of the synthesized GSC for dye-contaminated wastewater treatment is concluded.

  18. Formulation of soy oil products

    Directory of Open Access Journals (Sweden)

    Woerfel, John B.

    1995-12-01

    Full Text Available The paper comments different formulations of soy oil products such as salad and cooking oils, margarine, shortenings, commercial shortenings, frying shortenings, and fluid shortenings. Hydrogenation and its influence on final products is also included.

    El trabajo presenta diferentes formulaciones a base de aceite de soja tales como aceites para ensalada y cocinado, margarina, grasas sólidas (shortenings, grasas sólidas comerciales, grasas sólidas para frituras y grasas fluidas. Hace también referencia al proceso de hidrogenación y a sus efectos en los productos finales.

  19. Cassava processing wastewater as a platform for third generation biodiesel production

    Directory of Open Access Journals (Sweden)

    Cristina Neves

    Full Text Available ABSTRACT This study aimed to evaluate third generation biodiesel production by microalgae Phormidium autumnale using cassava processing wastewater as a platform. Experiments were performed in a heterotrophic bubble column bioreactor. The study focused on the evaluation of the bioreactor (batch and fed-batch of different operational modes and the analysis of biofuel quality. Results indicate that fed-batch cultivations improved system performance, elevating biomass and oil productions to 12.0 g L−1 and 1.19 g L−1, respectively. The composition of this oil is predominantly saturated (60 % and monounsaturated (39 %, resulting in a biodiesel that complys with U.S., European and Brazilian standards. The technological route developed indicates potential for sustainable production of bulk oil and biodiesel, through the minimization of water and chemical demands required to support such a process.

  20. Wastewater recycling technology for fermentation in polyunsaturated fatty acid production.

    Science.gov (United States)

    Song, Xiaojin; Ma, Zengxin; Tan, Yanzhen; Zhang, Huidan; Cui, Qiu

    2017-07-01

    To reduce fermentation-associated wastewater discharge and the cost of wastewater treatment, which further reduces the total cost of DHA and ARA production, this study first analyzed the composition of wastewater from Aurantiochytrium (DHA) and Mortierella alpina (ARA) fermentation, after which wastewater recycling technology for these fermentation processes was developed. No negative effects of DHA and ARA production were observed when the two fermentation wastewater methods were cross-recycled. DHA and ARA yields were significantly inhibited when the wastewater from the fermentation process was directly reused. In 5-L fed-batch fermentation experiments, using this cross-recycle technology, the DHA and ARA yields were 30.4 and 5.13gL -1 , respectively, with no significant changes (P>0.05) compared to the control group, and the water consumption was reduced by half compared to the traditional process. Therefore, this technology has great potential in industrial fermentation for polyunsaturated fatty acid production. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Removal of Oil and Grease as Emerging Pollutants of Concern (EPC in Wastewater Stream

    Directory of Open Access Journals (Sweden)

    Alade Abass O

    2011-12-01

    Full Text Available Wastewater characteristics, which depend on wastewater source, are increasingly becoming more toxic in recent times. The concentrations of oil and grease in wastewater streams have been observed to increase in wastewater stream with increasing adverse effects on the ecology. This results from the increasing use of oil and grease in high-demanded oil-processed foods, establishment and expansion of oil mills and refineries worldwide, as well as indiscriminate discharge of oil and grease into the water drains, domestically and industrially. This study reports the applications, efficiencies and challenges of the wastewater treatment techniques currently employed in the removal of oil and grease from the industrial wastewater and municipal water stream. The results shows that the concentrations of oil and grease injected into the ecosystem are of higher environmental impact and this needs to be given the desired attention. The desired development for effective removal of oil and grease as emerging pollutants of concern (EPC in wastewater stream are thus proposed. ABSTRAK: Ciri-ciri air sisa, bergantung kepada punca air sisa tersebut, menjadi semakin toksik akhir-akhir ini. Kepekatan minyak dan gris dalam air sisa anak sungai dilihat makin bertambah dalam air sisa anak sungai dengan bertambahnya kesan negatif ke atas ekologi. Ini disebabkan oleh peningkatan penggunaan minyak dan gris dalam makanan berproses yang tinggi permintaannya, penubuhan dan perkembangan kilang pertroleum dan loji penapisan di seluruh dunia. Minyak dan gris juga dibuang sewenang-wenangnya ke dalam parit air, dari kalangan domestik dan industry. Kajian ini membentangkan tentang aplikasi, keberkesanan dan teknik cabaran rawatan air buangan yang kini digunakan dalam pembuangan minyak dan gris dari air sisa industry dan air sungai perbandaran. Keputusan menunjukkan kepekatan minyak dan gris yang wujud dibuang ke dalam ekosistem mempunyai impak yang lebih tinggi terhadap persekitaran

  2. Harvesting, oil extraction, and conversion of local filamentous algae growing in wastewater into biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Grayburn, W.S.; Holbrook, G.P. [Department of Biological Sciences, Northern Illinois University, DeKalb, IL 60115 (United States); Tatara, R.A. [Department of Technology, Northern Illinois University, DeKalb, IL 60115 (United States); Rosentrater, K.A. [Department of Agricultural and Biosystems Engineering, Iowa State University, Ames, IA 50011 (United States)

    2013-07-01

    Algae are known to be a potential feedstock in the production of biodiesel fuel. Although much of the focus has been on microalgal species, macroalgae are also suitable as a source of lipids. In this study, a locally abundant (central Illinois) filamentous algae has been harvested from a water treatment plant; dried to about 10% of its initial weight; pulverized in a hammermill; and treated with methanol to extract the oil. The algae are a combination of several coexisting species including Cladophora sp. and Rhizoclonium. Oil yields ranged from 3% to 6%, by weight, of the dried mass. This oil was reacted by transesterification to yield fatty acid methyl esters (biodiesel fuel) with an overall mass conversion efficiency of 68%. A B5 blend of this algal biodiesel and petrodiesel was run in a 13.4-kW test engine. Measurements indicated similar performance compared to pure petrodiesel in terms of fuel efficiency and carbon dioxide and carbon monoxide exhaust emissions. Significantly, there was a 22% reduction in nitrogen oxides when using the B5 fuel. It has been demonstrated that filamentous macroalgae may be cultivated as biodiesel feedstock and have inherent advantages such as an ability to remove phosphorus and nitrogen compounds from wastewater, simplicity of harvesting, and natural resistance to local aquatic grazers and competing organisms.

  3. Comprehensive techno-economic analysis of wastewater-based algal biofuel production: A case study.

    Science.gov (United States)

    Xin, Chunhua; Addy, Min M; Zhao, Jinyu; Cheng, Yanling; Cheng, Sibo; Mu, Dongyan; Liu, Yuhuan; Ding, Rijia; Chen, Paul; Ruan, Roger

    2016-07-01

    Combining algae cultivation and wastewater treatment for biofuel production is considered the feasible way for resource utilization. An updated comprehensive techno-economic analysis method that integrates resources availability into techno-economic analysis was employed to evaluate the wastewater-based algal biofuel production with the consideration of wastewater treatment improvement, greenhouse gases emissions, biofuel production costs, and coproduct utilization. An innovative approach consisting of microalgae cultivation on centrate wastewater, microalgae harvest through flocculation, solar drying of biomass, pyrolysis of biomass to bio-oil, and utilization of co-products, was analyzed and shown to yield profound positive results in comparison with others. The estimated break even selling price of biofuel ($2.23/gallon) is very close to the acceptable level. The approach would have better overall benefits and the internal rate of return would increase up to 18.7% if three critical components, namely cultivation, harvest, and downstream conversion could achieve breakthroughs. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Pollutant removal-oriented yeast biomass production from high-organic-strength industrial wastewater: A review

    International Nuclear Information System (INIS)

    Yang, Min; Zheng, Shaokui

    2014-01-01

    Microbial single-cell-protein (SCP) production from high-organic-strength industrial wastewaters is considered an attractive method for both wastewater purification and resource utilization. In the last two decades, pollutant removal-oriented yeast SCP production processes, i.e., yeast treatment processes, have attracted a great deal of attention from a variety of research groups worldwide. Different from conventional SCP production processes, yeast treatment processes are characterized by higher pollutant removal rates, lower production costs, highly adaptive yeast isolates from nature, no excess nutrient supplements, and are performed under non-sterile conditions. Furthermore, yeast treatment processes are similar to bacteria-dominated conventional activated sludge processes, which offer more choices for yeast SCP production and industrial wastewater treatment. This review discusses why highly adaptive yeast species isolated from nature are used in the yeast treatment process rather than commercial SCP producers. It also describes the application of yeast treatment processes for treating high-carboxyhydrate, oil-rich and high-salinity industrial wastewater, focusing primarily on high-strength biodegradable organic substances, which usually account for the major fraction of biochemical oxygen demand. Also discussed is the biodegradation of xenobiotics, such as color (including dye and pigment) and toxic substances (including phenols, chlorophenols, polycyclic aromatic hydrocarbons, etc.), present in industrial wastewater. Based on molecular information of yeast community structures and their regulation in yeast treatment systems, we also discuss how to maintain efficient yeast species in yeast biomass and how to control bacterial and mold proliferation in yeast treatment systems. - Highlights: • Pollutant removal-oriented yeast SCP production processes offer more choices. • Highly adaptive yeast isolates replace commercial SCP producers. • Yeasts degrade

  5. Production of oil from Israeli oil shale

    International Nuclear Information System (INIS)

    Givoni, D.

    1993-01-01

    Oil shale can be utilized in two-ways: direct combustion to generate steam and power or retorting to produce oil or gas. PAMA has been developing both direct combustion and retorting processes. Its main effort is in the combustion. An oil shale fired steam boiler was erected in the Rotem industrial complex for demonstration purposes. PAMA has also been looking into two alternative retorting concepts - slow heating of coarse particles and fast heating of fine particles. The present paper provides operating data of oil shale processing in the following scheme: (a) retorting in moving bed, pilot and bench scale units, and (b) retorting in a fluidized bed, bench scale units. (author)

  6. Treatment of heavy oil wastewater by UASB-BAFs using the combination of yeast and bacteria.

    Science.gov (United States)

    Zou, Xiao-Ling

    2015-01-01

    A novel system integrating an upflow anaerobic sludge blanket (UASB) reactor and a two-stage biological aerated filter (BAF) system was investigated as advanced treatment of heavy oil wastewater with large amounts of dissolved recalcitrant organic substances and low levels of nitrogen and phosphorus nutrients. #1 BAF, inoculated with two yeast strains (Candida tropicalis and Rhodotorula dairenensis), was installed in the upper reaches of #2 BAF inoculated with activated sludge. During the 180-day study period, the chemical oxygen demand (COD), ammonia nitrogen (NH3-N), oil and polyaromatic hydrocarbons (PAHs) in the wastewater were removed by 90.2%, 90.8%, 86.5% and 89.4%, respectively. Although the wastewater qualities fluctuated and the hydraulic retention time continuously decreased, the effluent quality index met the national discharge standard steadily. The UASB process greatly improved the biodegradability of the wastewater, while #1 BAF played an important role not only in degrading COD but also in removing oil and high molecular weight PAHs. This work demonstrates that the hybrid UASB-BAFs system containing yeast-bacteria consortium has the potential to be used in bioremediation of high-strength oily wastewater.

  7. Conventional methods and emerging wastewater polishing technologies for palm oil mill effluent treatment: a review.

    Science.gov (United States)

    Liew, Wai Loan; Kassim, Mohd Azraai; Muda, Khalida; Loh, Soh Kheang; Affam, Augustine Chioma

    2015-02-01

    The Malaysian palm oil industry is a major revenue earner and the country is ranked as one of the largest producers in the world. However, growth of the industry is synonymous with a massive production of agro-industrial wastewater. As an environmental protection and public health concern, the highly polluting palm oil mill effluent (POME) has become a major attention-grabber. Hence, the industry is targeting for POME pollution abatement in order to promote a greener image of palm oil and to achieve sustainability. At present, most palm oil mills have adopted the ponding system for treatment. Due to the successful POME pollution abatement experiences, Malaysia is currently planning to revise the effluent quality standards towards a more stringent discharge limits. Hence, the current trend of POME research focuses on developing tertiary treatment or polishing systems for better effluent management. Biotechnologically-advanced POME tertiary (polishing) technologies as well as other physicochemical methods are gaining much attention as these processes are the key players to push the industry towards the goal of environmental sustainability. There are still ongoing treatment technologies being researched and the outcomes maybe available in a while. However, the research completed so far are compiled herein and reported for the first time to acquire a better perspective and insight on the subject with a view of meeting the new standards. To this end, the most feasible technology could be the combination of advanced biological processes (bioreactor systems) with extended aeration, followed by solids separation prior to discharge. Chemical dosing is favoured only if effluent of higher quality is anticipated. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. Ultrasonic characterization of vegetable oil product

    International Nuclear Information System (INIS)

    Sidek Hj Abd Aziz; Chow Sai Pew; Abdul Halim Shaari; Nor Azizah Shaari

    1992-01-01

    The ultrasonic wave velocity and attenuation of a number vegetable oil products were measured using an ultrasonic pulse echo overlap technique from room temperature up to 90 0 C. Among the liquid samples studied were refined bleach deodorized (RED) palm oil, palm olein, coconut oil, corn oil and soya bean oil. The velocity of sound in vegetable oil products varies from about 1200 to 200 ms-1 and decrease linearly as the temperature increases. The ultrasonic properties of the oil are much dependent on their viscosity, density, relaxation effect and vibrational anharmonicity

  9. Semi-industrial production of methane from textile wastewaters

    Energy Technology Data Exchange (ETDEWEB)

    Opwis, Klaus; Mayer-Gall, Thomas; Gutmann, Jochen S. [Deutsches Textilforschungszentrum Nord-West e.V., Krefeld (DE)] (and others)

    2012-12-15

    The enzymatic desizing of starch-sized cotton fabrics leads to wastewaters with an extremely high chemical oxygen demand due to its high sugar content. Nowadays, these liquors are still disposed without use, resulting in a questionable ecological pollution and high emission charges for cotton finishing manufacturers. In this paper, an innovative technology for the production of energy from textile wastewaters from cotton desizing was developed. Such desizing liquors were fermented by methane-producing microbes to biogas. For this purpose, a semi-industrial plant with a total volume of more than 500 L was developed and employed over a period of several weeks. The robust and trouble-free system produces high amounts of biogas accompanied by a significant reduction of the COD of more than 85%. With regard to growing standards and costs for wastewater treatment and disposal, the new process can be an attractive alternative for textile finishing enterprises in wastewater management, combining economic and ecological benefits. Moreover, the production of biogas from textile wastewaters can help to overcome the global energy gap within the next decades, especially with respect to the huge dimension of cotton pretreatment and, therefore, huge desizing activities worldwide.

  10. Pesticide interactions with soils affected by olive oil mill wastewater

    Science.gov (United States)

    Keren, Yonatan; Bukhanovsky, Nadezhda; Borisover, Mikhail

    2013-04-01

    Soil pesticide sorption is well known to affect the fate of pesticides, their bioavailability and the potential to contaminate air and water. Soil - pesticide interactions may be strongly influenced by soil organic matter (SOM) and organic matter (OM)-rich soil amendments. One special OM source in soils is related to olive oil production residues that may include both solid and liquid wastes. In the Mediterranean area, the olive oil production is considered as an important field in the agricultural sector. Due to the significant rise in olive oil production, the amount of wastes is growing respectively. Olive oil mill waste water (OMWW) is the liquid byproduct in the so-called "three phase" technological process. Features of OMWW include the high content of fatty aliphatic components and polyphenols and their often-considered toxicity. One way of OMWW disposal is the land spreading, e.g., in olive orchards. The land application of OMWW (either controlled or not) is supposed to affect the multiple soil properties, including hydrophobicity and the potential of soils to interact with pesticides. Therefore, there is both basic and applied interest in elucidating the interactions between organic compounds and soils affected by OMWW. However, little is known about the impact of OMWW - soil interactions on sorption of organic compounds, and specifically, on sorption of agrochemicals. This paper reports an experimental study of sorption interactions of a series of organic compounds including widely used herbicides such as diuron and simazine, in a range of soils that were affected by OMWW (i) historically or (ii) in the controlled land disposal experiments. It is demonstrated that there is a distinct increase in apparent sorption of organic chemicals in soils affected by OMWW. In selected systems, this increase may be explained by increase in SOM content. However, the SOM quality places a role: the rise in organic compound - soil interactions may both exceed the SOM

  11. Biohydrogen production and wastewater treatment from organic wastewater by anaerobic fermentation with UASB

    Science.gov (United States)

    Wang, Lu; Li, Yong-feng; Wang, Yi-xuan; Yang, Chuan-ping

    2010-11-01

    In order to discuss the ability of H2-production and wastewater treatment, an up-flow anaerobic sludge bed (UASB) using a synthesized substrate with brown sugar wastewater was conducted to investigate the hydrogen yield, hydrogen producing rate, fermentation type of biohydrogen production, and the chemical oxygen demand (COD) removal rate, respectively. The results show that when the biomass of inoculants was 22.5 g SSṡL-1 and the influent concentration, hydraulic retention time (HRT) and initial pH were within the ranges of 4000˜6000 mg CODṡL-1, 8 h and 5-5.5, respectively, and the biohydrogen producing reactor could work effectively. The maximum hydrogen production rate is 5.98 Lṡd-1. Simultaneously, the concentration of ethanol and acetic acid is around 80% of the aqueous terminal production in the system, which presents the typical ethanol type fermentation. pH is at the range of 4˜4.5 during the whole performing process, however, the removal rate of COD is just about 20%. Therefore, it's still needs further research to successfully achieve the biohydrogen production and wastewater treatment, simultaneously.

  12. CARWASH WASTEWATERS: CHARACTERISTICS, VOLUMES, AND TREATABILITY BY GRAVITY OIL SEPARATION

    OpenAIRE

    C. Fall

    2007-01-01

    The aim of this research was to determine the characteristics, volumes and treatability of Full-service carwash wastewaters in Toluca (Mexico State). The average water use for Exterior-only wash was 50 L per small-size car and 170 L per medium-size vehicle (pick up, van or light truck). The Full-service wash (exterior, engine and chassis) required 170 L per small-size car and 300 L per light truck. Wastewaters were generally emulsified and contained high contaminant loads (in average, 1100 mg...

  13. Integrative approach for utilization of olive mill wastewater and lebna's whey for ethanol production

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, M A; Hayek, B O; Al-Hmoud, N; Al-Gogazeh, L

    2009-09-15

    The industry of olive oil extraction in Jordan involves an intensive consumption of water and generates large quantities of olive mill wastewater (OMW). This wastewater has a high pollution risk with biological oxygen demand (BOD). The organic fraction of OMW includes sugars, tannins, polyphenols, polyalcohols, pectins and lipids. The presence of remarkable amounts of aromatic compounds in OMW is responsible for its phytotoxic and antimicrobial effects. The environmental problems and potential hazards caused by OMW had led olive oil producing countries to limit their discharge and to propose and develop new technologies for OMW treatments, such as physicochemical and biological treatments. In the present investigation lebna's whey a local byproduct of widely consumed local yogurt was used with OMW for ethanol production. The obtained results showed that the proteins of lebna's whey can remove substantial amounts of aromatic compounds present in OMW. This was reflected on the reduction of the intensity of black color of OMW and removal of 37% polyphenols. Moreover, the production of ethanol was ascertained in fermentation media composed of whey and in presence of various concentrations of OMW up to 20% OMW. The obtained results showed the possibility to develop a process for improvement and enhancement of ethanol production from whey and olive oil waste in mixed yeast cultures. (au)

  14. Reuse of drinking water treatment sludge for olive oil mill wastewater treatment.

    Science.gov (United States)

    Fragoso, R A; Duarte, E A

    2012-01-01

    Olive mill wastewater (OMW) results from the production of olive oil, which is an important traditional agro-industry in Mediterranean countries. In continuous three-phase centrifugation 1.0-1.2 m(3) of OMW are produced per ton of processed olives. Discharge of OMW is of serious environmental concern due to its high content of organic matter with phytotoxic properties, namely phenolic compounds. Meanwhile, drinking water treatment sludge (DWTS) is produced in high amounts and has long been considered as a waste for landfill. The aim of this work was the assessment of reusing DWTS for OMW treatment. High performance liquid chromatography (HPLC) analysis was carried out to determine the phenolic compounds present and to evaluate if they are recalcitrant. Treatability assays were performed using a dosage of DWTS from 50 to 300 g L(-1). Treatment efficiency was evaluated based on the removal of chemical oxygen demand (COD), biochemical oxygen demand (BOD), total solids (TS), total suspended solids (TSS), total volatile solids (TVS), oil and grease (OG), phenols (total phosphorous (TP) and HPLC fraction). Results from OMW HPLC characterization identified a total of 13 compounds; the major ones were hydroxytyrosol, tyrosol, caffeic acid, p-cumaric acid and oleuropein. Treatability assays led to a maximum reduction of about 90% of some of the phenolic compounds determined by HPLC. Addition of 200-300 g L(-1) of DWTS reduced 40-50% of COD, 45-50% of TP, a maximum of nearly 70% TSS and 45% for TS and TVS. The OG fraction showed a reduction of about 90%, achieved adding 300 g L(-1) od DWTS. This study points out the possibility of establishing an integrated management of OMW and DWTS, contributing to a decrease in the environmental impact of two industrial activities, olive oil production and drinking water treatment.

  15. Upgrading of technology of absorptive cleaning of oily wastewaters

    OpenAIRE

    Pavluh, L. I .

    2013-01-01

    Oily wastewater treatment technology is improved through the improvement of the absorptive properties of sorbents based on plant waste. The cost of flowsheets for treatment of wastewaters contaminated with oil products is presented.

  16. Improvement of biodegradability of oil wastewater contained PAM by pretreatment with Fenton oxidation

    International Nuclear Information System (INIS)

    Bao, M.; Wang, N.

    2008-01-01

    The use of polymer flooding in enhanced oil recovery operations has resulted in higher levels of polyacrylamide (PAM) found in oil wastewater. PAM is harmful to the environment, particularly the monomer acrylamide that is generated from PAM degradation. In this study, PAM derived from oil wastewater was pretreated by Fenton oxidation. This oxidation method is based on the use of a mixture of H 2 O 2 and iron salts which produce hydroxyl radicals in acidic conditions. The method offers a cost-effective source of hydroxyl radicals, using easy-to-handle reagents. The purpose of this study was to transform PAM to biodegradable intermediums. The optimal conditions for the Fenton reactions were also determined and described. Under optimal conditions, the removal ratios of PAM and chemical oxygen demand (COD) were 83.8 and 77 per cent respectively. It was concluded that Fenton's oxidation is an effective treatment to improved the biodegradability of PAM. 14 refs., 1 tab., 7 figs

  17. Caspian Oil and Gas: Production and Prospects

    National Research Council Canada - National Science Library

    Gelb, Bernard A

    2005-01-01

    .... The Caspian Sea region historically has been an oil and natural gas producer, but many believe that the region contains large reserves of oil and gas capable of much greater production than at present...

  18. Preparation and application of magnetic superhydrophobic polydivinylbenzene nanofibers for oil adsorption in wastewater.

    Science.gov (United States)

    Zhu, Xiaobiao; Tian, Ye; Li, Feifei; Liu, Yapeng; Wang, Xiaohui; Hu, Xiang

    2018-06-01

    Superhydrophobic materials have an excellent performance in oil adsorption. In this study, a novel magnetic polydivinylbenzene (PDVB) nanofiber was synthesized by the method of cation polymerization to adsorb oil from water. The magnetic PDVB was hollow nanofiber with Fe 3 O 4 nanoparticles embedded in its structure. The synthesis condition was optimized that the ratio of divinylbenzene (DVB) to boron fluoride ethyl ether (BFEE) was 10:1 (v/v), and the Fe 3 O 4 dosage was 0.175 g/g of DVB. The material showed an excellent oil adsorption performance in wastewater, and the oil concentration could be reduced from 2000 to 92.2 mg/L within 5 min. The magnetic PDVB had relatively high adsorption capacity (12 g/g) for oil, which could be attributed to its super hydrophobicity and one-dimensional nanostructure with high crosslinking degree. The isotherm study indicated that the magnetic PDVB adsorbed oil was an asymmetric or multilayer adsorption process. The material could be regenerated by simple squeeze and maintain its adsorption capacity after it has been used for 10 recycles. In real coking wastewater, the magnetic PDVB kept a good oil adsorption performance without the interference of various pollutants, indicating a wide prospect in practical use.

  19. Comparison between different liquid-liquid and solid phase methods of extraction prior to the identification of the phenolic fraction present in olive oil washing wastewater from the two-phase olive oil extraction system

    Directory of Open Access Journals (Sweden)

    S. Jiménez-Herrera

    2017-09-01

    Full Text Available Phenolic compounds from olive mill wastewater (OMW, are characterized by a strong antioxidant activity. At the same time, they represent an environmental problem because they are difficult to degrade. The purpose of this work was to identify these biologically active compounds in the OMW from two-phase olive oil production in order to convert a polluting residue into a source of natural antioxidants. After optimizing the extraction process of phenolic compounds using liquid-liquid extraction (LLE and solid phase extraction (SPE methods, it was determined that the most appropriate sequence comprised a previous centrifugation to remove the lipid fraction, followed by liquid extraction with ethyl acetate or SPE. The most important compounds identified in olive oil washing wastewater (OOWW were tyrosol, hydroxytyrosol and succinic acid; whereas the ones in the wastewater derived from the washing of the olives (OWW were cresol, catechol, 4-methylcatechol, hydrocinnamic acid and p-hydroxy-hydrocinnamic acid.

  20. Comparison between different liquid-liquid and solid phase methods of extraction prior to the identification of the phenolic fraction present in olive oil washing wastewater from the two-phase olive oil extraction system

    International Nuclear Information System (INIS)

    Jiménez-Herrera, S.; Ochando-Pulido, J.M.; Martínez-Ferez, A.

    2017-01-01

    Phenolic compounds from olive mill wastewater (OMW), are characterized by a strong antioxidant activity. At the same time, they represent an environmental problem because they are difficult to degrade. The purpose of this work was to identify these biologically active compounds in the OMW from two-phase olive oil production in order to convert a polluting residue into a source of natural antioxidants. After optimizing the extraction process of phenolic compounds using liquid-liquid extraction (LLE) and solid phase extraction (SPE) methods, it was determined that the most appropriate sequence comprised a previous centrifugation to remove the lipid fraction, followed by liquid extraction with ethyl acetate or SPE. The most important compounds identified in olive oil washing wastewater (OOWW) were tyrosol, hydroxytyrosol and succinic acid; whereas the ones in the wastewater derived from the washing of the olives (OWW) were cresol, catechol, 4-methylcatechol, hydrocinnamic acid and p-hydroxy-hydrocinnamic acid. [es

  1. Environmental signatures and effects of an oil and gas wastewater spill in the Williston Basin, North Dakota

    Science.gov (United States)

    Cozzarelli, Isabelle M.; Skalak, Katherine; Kent, D.B.; Engle, Mark A.; Benthem, Adam J.; Mumford, Adam; Haase, Karl B.; Farag, Aïda M.; Harper, David; Nagel, S. C.; Iwanowicz, Luke R.; Orem, William H.; Akob, Denise M.; Jaeschke, Jeanne B.; Galloway, Joel M.; Kohler, Matthias; Stoliker, Deborah L.; Jolly, Glenn D.

    2017-01-01

    Wastewaters from oil and gas development pose largely unknown risks to environmental resources. In January 2015, 11.4 M L (million liters) of wastewater (300 g/L TDS) from oil production in the Williston Basin was reported to have leaked from a pipeline, spilling into Blacktail Creek, North Dakota. Geochemical and biological samples were collected in February and June 2015 to identify geochemical signatures of spilled wastewaters as well as biological responses along a 44-km river reach. February water samples had elevated chloride (1030 mg/L) and bromide (7.8 mg/L) downstream from the spill, compared to upstream levels (11 mg/L and < 0.4 mg/L, respectively). Lithium (0.25 mg/L), boron (1.75 mg/L) and strontium (7.1 mg/L) were present downstream at 5–10 times upstream concentrations. Light hydrocarbon measurements indicated a persistent thermogenic source of methane in the stream. Semi-volatile hydrocarbons indicative of oil were not detected in filtered samples but low levels, including tetramethylbenzenes and di-methylnaphthalenes, were detected in unfiltered water samples downstream from the spill. Labile sediment-bound barium and strontium concentrations (June 2015) were higher downstream from the Spill Site. Radium activities in sediment downstream from the Spill Site were up to 15 times the upstream activities and, combined with Sr isotope ratios, suggest contributions from the pipeline fluid and support the conclusion that elevated concentrations in Blacktail Creek water are from the leaking pipeline. Results from June 2015 demonstrate the persistence of wastewater effects in Blacktail Creek several months after remediation efforts started. Aquatic health effects were observed in June 2015; fish bioassays showed only 2.5% survival at 7.1 km downstream from the spill compared to 89% at the upstream reference site. Additional potential biological impacts were indicated by estrogenic inhibition in downstream waters. Our findings demonstrate that

  2. Environmental signatures and effects of an oil and gas wastewater spill in the Williston Basin, North Dakota.

    Science.gov (United States)

    Cozzarelli, I M; Skalak, K J; Kent, D B; Engle, M A; Benthem, A; Mumford, A C; Haase, K; Farag, A; Harper, D; Nagel, S C; Iwanowicz, L R; Orem, W H; Akob, D M; Jaeschke, J B; Galloway, J; Kohler, M; Stoliker, D L; Jolly, G D

    2017-02-01

    Wastewaters from oil and gas development pose largely unknown risks to environmental resources. In January 2015, 11.4ML (million liters) of wastewater (300g/L TDS) from oil production in the Williston Basin was reported to have leaked from a pipeline, spilling into Blacktail Creek, North Dakota. Geochemical and biological samples were collected in February and June 2015 to identify geochemical signatures of spilled wastewaters as well as biological responses along a 44-km river reach. February water samples had elevated chloride (1030mg/L) and bromide (7.8mg/L) downstream from the spill, compared to upstream levels (11mg/L and <0.4mg/L, respectively). Lithium (0.25mg/L), boron (1.75mg/L) and strontium (7.1mg/L) were present downstream at 5-10 times upstream concentrations. Light hydrocarbon measurements indicated a persistent thermogenic source of methane in the stream. Semi-volatile hydrocarbons indicative of oil were not detected in filtered samples but low levels, including tetramethylbenzenes and di-methylnaphthalenes, were detected in unfiltered water samples downstream from the spill. Labile sediment-bound barium and strontium concentrations (June 2015) were higher downstream from the Spill Site. Radium activities in sediment downstream from the Spill Site were up to 15 times the upstream activities and, combined with Sr isotope ratios, suggest contributions from the pipeline fluid and support the conclusion that elevated concentrations in Blacktail Creek water are from the leaking pipeline. Results from June 2015 demonstrate the persistence of wastewater effects in Blacktail Creek several months after remediation efforts started. Aquatic health effects were observed in June 2015; fish bioassays showed only 2.5% survival at 7.1km downstream from the spill compared to 89% at the upstream reference site. Additional potential biological impacts were indicated by estrogenic inhibition in downstream waters. Our findings demonstrate that environmental signatures

  3. High-rate fermentative hydrogen production from beverage wastewater

    International Nuclear Information System (INIS)

    Sivagurunathan, Periyasamy; Sen, Biswarup; Lin, Chiu-Yue

    2015-01-01

    Highlights: • Hybrid immobilized-bacterial cells show stable operation over 175 days. • Low HRT of 1.5 h shows peak hydrogen production rate of 55 L/L-d. • Electricity generation is 9024 kW-d from 55 L/L-d hydrogen using beverage wastewater. • Granular sludge formed only at 2–3 h HRT with presence of Selenomonas sp. - Abstract: Hydrogen production from beverage industry wastewater (20 g/L hexose equivalent ) using an immobilized cell reactor with a continuous mode of operation was studied at various hydraulic retention times (HRT, 8–1.5 h). Maximum hydrogen production rate (HPR) of 55 L/L-d was obtained at HRT 1.5 h (an organic loading of 320 g/L-d hexose equivalent ). This HPR value is much higher than those of other industrial wastewaters employed in fermentative hydrogen production. The cell biomass concentration peaked at 3 h HRT with a volatile suspended solids (VSS) concentration of 6.31 g/L (with presence of self-flocculating Selenomonas sp.), but it dropped to 3.54 gVSS/L at 1.5 h HRT. With the shortening of HRT, lactate concentration increased but the concentration of the dominant metabolite butyrate did not vary significantly. The Clostridium species dynamics was not significantly affected, but total microbial community structure changed with respect to HRT variation as evident from PCR–DGGE analyses. Analysis of energy production rate suggests that beverage wastewater is a high energy yielding feedstock, and can replace 24% of electricity consumption in a model beverage industry

  4. Characterization of Lipase from Bacillus subtilisI-4 and Its Potential Use in Oil Contaminated Wastewater

    Directory of Open Access Journals (Sweden)

    Syeda Abeer Iqbal

    2015-10-01

    Full Text Available ABSTRACTA lipase producing bacterium was isolated from oil contaminated effluents of various industries from Sheikhupura Road, Pakistan, and, on the basis of biochemical and 16S rRNA ribotyping, was identified asBacillus subtilis. The optimum temperature and pH for the growth of the culture were 37ºC and 7.0, respectively.B. subtilis I-4 had a lag phase of 4 h in LB medium while this phase prolonged to 6 h in oil containing medium. The optimum temperature and pH for the enzyme activity were 50ºC and 7.0, respectively. Maximum lipase activity was found in the presence of Ca ions. Olive oil and Tween 80 induced lipase gene in the bacterium while concentration of oil greater than 2% retarded the growth of the organism. In addition to lipaseB. subtilis I-4 also produced alkane hydroxylase and biosurfactant which could make this bacterium potential candidate for lipase production as well as bioremediation of oil-contaminated wastewater.

  5. Cultivation of algae consortium in a dairy farm wastewater for biodiesel production

    Directory of Open Access Journals (Sweden)

    S. Hena

    2015-06-01

    Full Text Available Dairy farm wastewaters are potential resources for production of microalgae biofuels. A study was conducted to evaluate the capability of production of biodiesel from consortium of native microalgae culture in dairy farm treated wastewater. Native algal strains were isolated from dairy farm wastewaters collection tank (untreated wastewater as well as from holding tank (treated wastewater. The consortium members were selected on the basis of fluorescence response after treating with Nile red reagent. Preliminary studies of two commercial and consortium of ten native strains of algae showed good growth in wastewaters. A consortium of native strains was found capable to remove more than 98% nutrients from treated wastewater. The biomass production and lipid content of consortium cultivated in treated wastewater were 153.54 t ha−1 year−1 and 16.89%, respectively. 72.70% of algal lipid obtained from consortium could be converted into biodiesel.

  6. Efficiency of sugarcane bagasse-based sorbents for oil removal from engine washing wastewater.

    Science.gov (United States)

    Guilharduci, Viviane Vasques da Silva; Martelli, Patrícia Benedini; Gorgulho, Honória de Fátima

    2017-01-01

    This work evaluates the efficiency of sugarcane bagasse-based sorbents in the sorption of oil from engine washing wastewater. The sorbents were obtained from sugarcane bagasse in the natural form (SB-N) and modified with either acetic anhydride (SB-Acet) or 3-aminopropyltriethoxysilane (SB-APTS). The results showed that the sorption capacity of these materials decreased in the following order: SB-APTS > SB-N > SB-Acet. The superior oil sorption capacity observed for SB-APTS was attributed to the polar amino end groups in the silane structure, which acted to increase the hydrophilic character of the fibers. However, all the sorbents obtained in this study were able to clean a real sample of wastewater from engine washing, leading to significant reductions in suspended matter, sediment, anionic surfactants, and turbidity.

  7. Developing new markets for oil sands products

    International Nuclear Information System (INIS)

    Crandall, G.

    2004-01-01

    This paper presents a review by Purvin and Gertz of western Canadian crude oil supply. This energy consulting firm provides advise to the energy sector. It suggests that oil sands production will surpass declining conventional production. Oil sands supply includes bitumen, synthetic crude oil (SCO), and diluent. It is forecasted that oil sands will increase from 42 per cent of western supply in 2002 to 78 per cent in 2015. The potential of Alberta's oil sands was discussed along with a recent study of refined products and petrochemicals from bitumen. Upgrading, refining and petrochemical case studies were presented. The author examined if a Canadian oil sands upgrading project with high capital costs can be competitive with competing projects in the United States and internationally. In addition to supply and demand issues, the presentation examined infrastructure capability and market potential in the United States. The economic potential and risks of preferred business cases compared to upgrading to SCO were also evaluated. 15 figs

  8. Treatment of Oily Wastewater Produced From Old Processing Plant of North Oil Company

    Directory of Open Access Journals (Sweden)

    Dr. Faris Hammoodi Al-Ani

    2012-03-01

    Full Text Available The main objectives of this research were to study and analyses oily wastewater characteristics originating from old-processing plant of North Oil Company and to find a suitable and simple method to treat the waste so it can be disposed off safely. The work consists of two stages; the first was the study of oily wastewater characteristics and its negative impacts. The results indicated that oil and grease were the most dominant pollutant with concentration range between 1069 – 3269.3 mg/l that must be removed; other pollutants were found to be within Iraqi and EPA standards. The next stage was the use of these characteristics to choose the proper technology to treat that wastewater. This stage was divided into two stages: the first stage was a jar tests to find the optimum doses of alum, lime and powdered activated carbon (PAC. The second stage was the treatment by a batch pilot plant constructed for this purpose employing the optimum doses as determined from the first stage to treat the waste using a flotation unit followed by a filtration-adsorption unit. The removal efficiencies of flotation unit for oil and grease, COD, and T.S.S found to be 0.9789, 0.974, and 0.9933, respectively, while the removal efficiency for T.D.S was very low 0.0293. From filtration – adsorption column the removal efficiencies of oil and grease, T.D.S, COD, and T.S.S were found to be 0.9486, 0.8908, 0.6870, and 0.7815, respectively. The overall removal efficiencies of pilot plant were 0.9986, 0.8939, 0.9921, and 0.9950, respectively. The results indicated that this type of treatment was the simplest and most effective method that can be used to treat produced oily wastewater before disposal

  9. Shifts in microbial community structure and function in surface waters impacted by unconventional oil and gas wastewater revealed by metagenomics

    Science.gov (United States)

    Fahrenfeld, N.L.; Reyes, Hannah Delos; Eramo, Alessia; Akob, Denise M.; Mumford, Adam; Cozzarelli, Isabelle M.

    2017-01-01

    Unconventional oil and gas (UOG) production produces large quantities of wastewater with complex geochemistry and largely uncharacterized impacts on surface waters. In this study, we assessed shifts in microbial community structure and function in sediments and waters upstream and downstream from a UOG wastewater disposal facility. To do this, quantitative PCR for 16S rRNA and antibiotic resistance genes along with metagenomic sequencing were performed. Elevated conductivity and markers of UOG wastewater characterized sites sampled downstream from the disposal facility compared to background sites. Shifts in overall high level functions and microbial community structure were observed between background sites and downstream sediments. Increases in Deltaproteobacteria and Methanomicrobia and decreases in Thaumarchaeota were observed at downstream sites. Genes related to dormancy and sporulation and methanogenic respiration were 18–86 times higher at downstream, impacted sites. The potential for these sediments to serve as reservoirs of antimicrobial resistance was investigated given frequent reports of the use of biocides to control the growth of nuisance bacteria in UOG operations. A shift in resistance profiles downstream of the UOG facility was observed including increases in acrB and mexB genes encoding for multidrug efflux pumps, but not overall abundance of resistance genes. The observed shifts in microbial community structure and potential function indicate changes in respiration, nutrient cycling, and markers of stress in a stream impacted by UOG waste disposal operations.

  10. Electrochemical pretreatment of heavy oil refinery wastewater using a three-dimensional electrode reactor

    Energy Technology Data Exchange (ETDEWEB)

    Wei Lingyong [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Guo Shaohui, E-mail: cupgsh@163.co [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Yan Guangxu; Chen Chunmao [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Jiang Xiaoyan [Liaohe Petrochemical Branch Company, PetroChina, Panjin 124022 (China)

    2010-12-01

    The pretreatment of heavy oil refinery wastewater (HORW) was experimentally investigated using a three-dimensional electrode reactor (TDER) with granular activated carbon (GAC) and porous ceramsite particle (PCP) as the combination particle electrode and DSA type anodes as the anode. The results showed that higher chemical oxygen demand (COD) removal was obtained in TDER comparing with the two-dimensional electrode reactor (without particle electrodes packed), and combination particle electrode was favorable to improve the COD removal efficiency and reduce the energy consumption. The treated HORW under the optimal experimental condition (GAC percentage = 75%, current density = 30 mA/cm{sup 2}, pH not adjusted and treatment time = 100 min) presented that the removal efficiencies of COD, total organic carbon and toxicity units were 45.5%, 43.3% and 67.2%, respectively, and the ratio of 5-day biochemical oxygen demand to COD was increased from 0.10 to 0.29, which is beneficial for further biological treatment. Furthermore, the application of electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry to characterize polar compounds in HORW and their oxidation products was well demonstrated to reveal the composition variation.

  11. Electrochemical pretreatment of heavy oil refinery wastewater using a three-dimensional electrode reactor

    International Nuclear Information System (INIS)

    Wei Lingyong; Guo Shaohui; Yan Guangxu; Chen Chunmao; Jiang Xiaoyan

    2010-01-01

    The pretreatment of heavy oil refinery wastewater (HORW) was experimentally investigated using a three-dimensional electrode reactor (TDER) with granular activated carbon (GAC) and porous ceramsite particle (PCP) as the combination particle electrode and DSA type anodes as the anode. The results showed that higher chemical oxygen demand (COD) removal was obtained in TDER comparing with the two-dimensional electrode reactor (without particle electrodes packed), and combination particle electrode was favorable to improve the COD removal efficiency and reduce the energy consumption. The treated HORW under the optimal experimental condition (GAC percentage = 75%, current density = 30 mA/cm 2 , pH not adjusted and treatment time = 100 min) presented that the removal efficiencies of COD, total organic carbon and toxicity units were 45.5%, 43.3% and 67.2%, respectively, and the ratio of 5-day biochemical oxygen demand to COD was increased from 0.10 to 0.29, which is beneficial for further biological treatment. Furthermore, the application of electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry to characterize polar compounds in HORW and their oxidation products was well demonstrated to reveal the composition variation.

  12. Treatability and kinetics studies of mesophilic aerobic biodegradation of high oil and grease pet food wastewater

    International Nuclear Information System (INIS)

    Liu, Victor Lei; Nakhla, G.; Bassi, A.

    2004-01-01

    In this work, batch activated sludge studies were investigated for the treatment of raw pet food wastewater characterized by oil and grease concentrations of 50,000-66,000 mg/L, COD and BOD concentrations of 100,000 and 80,000 mg/L, respectively, as well as effluent from an existing anaerobic digester treating the aforementioned wastewater. A pre-treatment process, dissolved air flotation (DAF) achieved 97-99% reduction in O and G to about 400-800 mg/L, which is still atypically high for AS. The batch studies were conducted using a 4-L bioreactor at room temperature (21 deg. C) under different conditions. The experimental results showed for the DAF pretreated effluent, 92% COD removal efficiency can be achieved by using conventional activated sludge system at a 5 days contact time and applied initial soluble COD to biomass ratio of 1.17 mg COD/mg VSS. Similarly for the digester effluent at average oil and grease concentrations of 13,500 mg/L, activated sludge affected 63.7-76.2% soluble COD removal at 5 days. The results also showed that all kinetic data best conformed to the zero order biodegradation model with a low biomass specific maximum substrate utilization rate of 0.168 mg COD/mg VSS day reflecting the slow biodegradability of the wastewater even after 99% removal of oil and grease

  13. Productivity assessment of Angola's oil blocks

    International Nuclear Information System (INIS)

    Barros, Carlos Pestana; Managi, Shunsuke

    2009-01-01

    This paper analyzes the change in productivity as a result of Angola oil policy from 2001 to 2007. Angola oil blocks are the main source of tax receipts and, therefore, strategically important for public finances. A Malmquist index with the input technological bias is applied to measure productivity change. Oil blocks on average became both more efficient and experienced technological progress. Our results indicate that the traditional growth accounting method, which assumes Hicks neutral technological change, is not appropriate for analyzing changes in productivity for Angola oil blocks. Policy implications are derived. (author)

  14. A catalogue of crude oil and oil product properties, 1990

    International Nuclear Information System (INIS)

    Bobra, M.A.; Callaghan, S.

    1990-09-01

    This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 109 refs

  15. A catalogue of crude oil and oil product properties, 1992

    International Nuclear Information System (INIS)

    Whiticar, S.; Bobra, M.; Liuzzo, P.; Callaghan, S.; Fingas, M.; Jokuty, P.; Ackerman, F.; Cao, J.

    1993-02-01

    This catalogue is a compilation of available data on crude oils and petroleum products. The emphasis of the catalogue is upon oils which could potentially impact Canada's environment. Other oils which are unlikely to be of direct Canadian concern are also included because they have been well characterized and used in relevant studies. The properties listed for each oil are those which will provide an indication of a spilled oil's environmental behaviour and effects. The properties on which data is provided include API gravity, density, viscosity, interfacial tension, pour point, flash point, vapor pressure, volatility and component distribution, emulsion formation tendency and stability, weathering, dispersability, major hydrocarbon groups, aqueous solubility, toxicity, sulfur content, fire point, and wax content. Most of the chemical-physical properties listed in this catalogue were measured using standard tests. For certain properties, data are given at different temperatures and for different degrees of oil weathering. An oil's degree of weathering is expresed as the volume or weight percent evaporated from the fresh oil. Weathered oils used for testing were artificially weathered by gas stripping following the method of Mackay and Stiver. 140 refs

  16. Briquette fuel production from wastewater sludge of beer industry and biodiesel production wastes

    Science.gov (United States)

    Nusong, P.; Puajindanetr, S.

    2018-04-01

    The production of industrial wastes is increasing each year. Current methods of waste disposal are severely impacting the environment. Utilization of industrial wastes as an alternative material for fuel is gaining interest due to its environmental friendliness. Thus, the objective of this research was to study the optimum condition for fuel briquettes produced from wastewater sludge of the beer industry and biodiesel production wastes. This research is divided into two parts. Part I will study the effects of carbonization of brewery wastewater sludge for high fixed carbon. Part II will study the ratio between brewery wastewater sludge and bleaching earth for its high heating value. The results show that the maximum fixed carbon of 10.01% by weight was obtained at a temperature of 350 °C for 30 minutes. The appropriate ratio of brewery wastewater sludge and bleaching earth by weight was 95:5. This condition provided the highest heating value of approximately 3548.10 kcal/kg.

  17. Aviation fuel and future oil production scenarios

    International Nuclear Information System (INIS)

    Nygren, Emma; Aleklett, Kjell; Hoeoek, Mikael

    2009-01-01

    Most aviation fuels are jet fuels originating from crude oil. Crude oil must be refined to be useful and jet fuel is only one of many products that can be derived from crude oil. Jet fuel is extracted from the middle distillates fraction and competes, for example, with the production of diesel. Crude oil is a limited natural resource subject to depletion and several reports indicate that the world's crude oil production is close to the maximum level and that it will start to decrease after reaching this maximum. A post-Kyoto political agenda to reduce oil consumption will have the same effect on aviation fuel production as a natural decline in the crude oil production. On the other hand, it is predicted by the aviation industry that aviation traffic will keep on increasing. The industry has put ambitious goals on increases in fuel efficiency for the aviation fleet. Traffic is predicted to grow by 5% per year to 2026, fuel demand by about 3% per year. At the same time, aviation fuel production is predicted to decrease by several percent each year after the crude oil production peak is reached resulting in a substantial shortage of jet fuel by 2026. The aviation industry will have a hard time replacing this with fuel from other sources, even if air traffic remains at current levels.

  18. Transgenic oil palm: production and projection.

    Science.gov (United States)

    Parveez, G K; Masri, M M; Zainal, A; Majid, N A; Yunus, A M; Fadilah, H H; Rasid, O; Cheah, S C

    2000-12-01

    Oil palm is an important economic crop for Malaysia. Genetic engineering could be applied to produce transgenic oil palms with high value-added fatty acids and novel products to ensure the sustainability of the palm oil industry. Establishment of a reliable transformation and regeneration system is essential for genetic engineering. Biolistic was initially chosen as the method for oil palm transformation as it has been the most successful method for monocotyledons to date. Optimization of physical and biological parameters, including testing of promoters and selective agents, was carried out as a prerequisite for stable transformation. This has resulted in the successful transfer of reporter genes into oil palm and the regeneration of transgenic oil palm, thus making it possible to improve the oil palm through genetic engineering. Besides application of the Biolistics method, studies on transformation mediated by Agrobacterium and utilization of the green fluorescent protein gene as a selectable marker gene have been initiated. Upon the development of a reliable transformation system, a number of useful targets are being projected for oil palm improvement. Among these targets are high-oleate and high-stearate oils, and the production of industrial feedstock such as biodegradable plastics. The efforts in oil palm genetic engineering are thus not targeted as commodity palm oil. Due to the long life cycle of the palm and the time taken to regenerate plants in tissue culture, it is envisaged that commercial planting of transgenic palms will not occur any earlier than the year 2020.

  19. Perspectives of microbial oils for biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    Li Qiang; Du Wei; Liu Dehua [Tsinghua Univ., Beijing (China). Dept. of Chemical Engineering

    2008-10-15

    Biodiesel has become more attractive recently because of its environmental benefits, and the fact that it is made from renewable resources. Generally speaking, biodiesel is prepared through transesterification of vegetable oils or animal fats with short chain alcohols. However, the lack of oil feedstocks limits the large-scale development of biodiesel to some extent. Recently, much attention has been paid to the development of microbial, oils and it has been found that many microorganisms, such as algae, yeast, bacteria, and fungi, have the ability to accumulate oils under some special cultivation conditions. Compared to other plant oils, microbial oils have many advantages, such as short life cycle, less labor required, less affection by venue, season and climate, and easier to scale up. With the rapid expansion of biodiesel, microbial oils might become one of potential oil feedstocks for biodiesel production in the future, though there are many works associated with microorganisms producing oils need to be carried out further. This review is covering the related research about different oleaginous microorganisms producing oils, and the prospects of such microbial oils used for biodiesel production are also discussed. (orig.)

  20. Options for reducing oil content of sludge from a petroleum wastewater treatment plant.

    Science.gov (United States)

    Kwon, Tae-Soon; Lee, Jae-Young

    2015-10-01

    Wastewater treatment plants at petroleum refineries often produce substantial quantities of sludge with relatively high concentrations of oil. Disposal of this waste is costly, in part because the high oil content requires use of secure disposal methods akin to handling of hazardous wastes. This article examines the properties of oily sludge and evaluates optional methods for reducing the oil content of this sludge to enable use of lower cost disposal methods. To reduce the oil content or break the structure of oily sludge, preliminary lab-scale experiments involving mechanical treatment, surfactant extraction, and oxidation are conducted. By applying surfactants, approximately 36% to 45% of oils are extracted from oily sludge. Of this, about 33% of oils are rapidly oxidised via radiation by an electron beam within 10 s of exposure. The Fenton reaction is effective for destruction of oily sludge. It is also found that 56% of oils were removed by reacting oily sludge with water containing ozone of 0.5 mg l(-1) over a period of 24 h. Oxidation using ozone thus can also be effectively used as a pretreatment for oily sludge. © The Author(s) 2015.

  1. Economic assessment of biodiesel production from wastewater sludge.

    Science.gov (United States)

    Chen, Jiaxin; Tyagi, Rajeshwar Dayal; Li, Ji; Zhang, Xiaolei; Drogui, Patrick; Sun, Feiyun

    2018-04-01

    Currently, there are mainly two pathways of the biodiesel production from wastewater sludge including 1) directly extracting the lipid in sludge and then converting the lipid to biodiesel through trans-esterification, and 2) employing sludge as medium to cultivate oleaginous microorganism to accumulate lipid and then transferring the lipid to biodiesel. So far, the study was still in research stage and its cost feasibility was not yet investigated. In this study, biodiesel production from wastewater sludge was designed and the cost was estimated with SuperPro Designer. With consideration of converting the lipid in raw sludge to biodiesel, the unit production cost was 0.67 US $/kg biodiesel (0.59 US $/L biodiesel). When the sludge was used as medium to grow oleaginous microorganism to accumulate lipid for producing biodiesel, the unit production cost was 1.08 US $/kg biodiesel (0.94 US $/L biodiesel). The study showed that sludge has great potential in biodiesel production. Copyright © 2018 Elsevier Ltd. All rights reserved.

  2. Process model economics of xanthan production from confectionery industry wastewaters.

    Science.gov (United States)

    Bajić, Bojana Ž; Vučurović, Damjan G; Dodić, Siniša N; Grahovac, Jovana A; Dodić, Jelena M

    2017-12-01

    In this research a process and cost model for a xanthan production facility was developed using process simulation software (SuperPro Designer ® ). This work represents a novelty in the field for two reasons. One is that xanthan gum has been produced from several wastes but never from wastewaters from confectionery industries. The other more important is that the aforementioned software, which in intended exclusively for bioprocesses, is used for generating a base case, i.e. starting point for transferring the technology to industrial scales. Previously acquired experimental knowledge about using confectionery wastewaters from five different factories as substitutes for commercially used cultivation medium have been incorporated into the process model in order to obtain an economic viability of implementing such substrates. A lower initial sugar content in the medium based on wastewater (28.41 g/L) compared to the synthetic medium (30.00 g/L) gave a lower xanthan content at the end of cultivation (23.98 and 26.27 g/L, respectively). Although this resulted in somewhat poorer economic parameters, they were still in the range of being an investment of interest. Also the possibility of utilizing a cheap resource (waste) and reducing pollution that would result from its disposal has a positive effect on the environment. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Optimization and performance evaluation for nutrient removal from palm oil mill effluent wastewater using microalgae

    Science.gov (United States)

    Ibrahim, Raheek I.; Wong, Z. H.; Mohammad, A. W.

    2015-04-01

    Palm oil mill effluent (POME) wastewater was produced in huge amounts in Malaysia, and if it discharged into the environment, it causes a serious problem regarding its high content of nutrients. This study was devoted to POME wastewater treatment with microalgae. The main objective was to find the optimum conditions (retention time, and pH) in the microalgae treatment of POME wastewater considering retention time as a most important parameter in algae treatment, since after the optimum conditions there is a diverse effect of time and pH and so, the process becomes costly. According to our knowledge, there is no existing study optimized the retention time and pH with % removal of nutrients (ammonia nitrogen NH3-N, and orthophosphorous PO43-) for microalgae treatment of POME wastewater. In order to achieve with optimization, a central composite rotatable design with a second order polynomial model was used, regression coefficients and goodness of fit results in removal percentages of nutrients (NH3-N, and PO43-) were estimated.WinQSB technique was used to optimize the surface response objective functionfor the developed model. Also experiments were done to validate the model results.The optimum conditions were found to be 18 day retention time for ammonia nitrogen, and pH of 9.22, while for orthophosphorous, 15 days were indicated as the optimum retention time with a pH value of 9.2.

  4. Bioremediation potential of the Sava river water polluted by oil refinery wastewater

    International Nuclear Information System (INIS)

    Jaksic, B.; Matavulj, M.; Vukic, Lj.; Radnovic, D.

    2002-01-01

    Microbial enumeration is a screening-level tool which can be used to evaluate in-situ response of water microorganisms to petroleum hydrocarbon contamination as well as for evaluating enhanced bioremediation potential of petroleum hydrocarbon contamination. In this investigations the increase between 17- and 44-fold of number of heterotrophs in hydrocarbon contaminated the Sava River water when compared with the no contaminated river water have been recorded. The significant increase of number of facultative oligotrophs in the river Sava water downstream of wastewater discharge (between 70- and almost 100-fold higher number) direct to the conclusion that oligotrophic bacteria (adapted to the environments with low amount of easy-to-degrade nutrients, oligocarbophilic microorganisms) could be better indicator of water bioremediation potential than number of heterotrophic (THR) bacteria. Quantitative composition of heterotrophic, facultative oligotrophic, crude oil degrading, and other physiological groups of bacteria, being, as a rule, higher in samples taken downstream of the waste-water discharge, testify about high biodegradative potential of the River Sava microbial community, if the oil refinery wastewater is taken into consideration. (author)

  5. Olive oil mill wastewater for remediation of slag contaminated soil.

    Science.gov (United States)

    Ferrara, Luciano; Panzella, Lucia; Napolitano, Alessandra; Giudicianni, Italo; d'Ischia, Marco; Arienzo, Michele

    2013-12-01

    Two olive mill wastewaters (OMW) samples, OMWa and OMWb, containing different polyphenolic loads were used for decontaminating an unauthorized dump site in the Campania region, south Italy. In a bench-scale experiment, OMWa at pH 6.0 (OMWapH6.0) and 4.7 (OMWapH4.7), OMWb at pH 4.7 (OMWbpH4.7) and OMWa free of the polyphenolic moiety polyphenol-free OMWa (PF-OMWa) were added to the soil for a 96 h contact time. At 96 h, OMWapH4.7 was more effective than OMWapH6.0, with Cd, Cu, Pb and Zn removal percentages of 30.7-68.1. Cd and Pb levels were 6.0 and 915 mg kg(-1), respectively, decreasing below the regulatory limits for industrial and commercial areas (15.0 and 1 × 10(3) mg kg(-1), respectively). A threefold decrease in Zn levels was also observed from 13.5 × 10(3) to 4.3 × 10(3) mg kg(-1). The metal removal efficiency of PF-OMWa dropped from 30.7 % to 15.6 % for Cd and from 37.9 % to 1.3 % for Pb. OMWbpH4.7 at 96 h was more efficient than OMWapH4.7, with mean removal percentages of 32.5 versus 7.8, respectively.

  6. Oil Production, Refining and Transportation in Canada

    Directory of Open Access Journals (Sweden)

    Igbal A. Guliyev

    2015-01-01

    Full Text Available The article deals with fuel and energy complex of Canada as one of the largest manufacturers of primary energy in the world, which provides up to 6 percent of the world energy supply. Only the Russian Federation, PRC, the United States of America and the Kingdom of Saudi Arabia have larger production volumes. However, oil plays the most significant role in Canada's energy exports. It is estimated that its proven reserves are sufficient to meet the demand for 140 years at current production rate. The relevance of the study, including the analysis of fuel and energy complex of Canada, is due to the fact that such comparison and synthesis of data on the amount of recoverable oil reserves, the volume of its production, imports, exports and transit of oil and oil products, the distribution of oil for transportation (via pipelines, rail, sea, road, strategic oil field, refining and transportation of oil and oil products development projects, as well as implementation of Canada's best practices in the Russian Federation, is being developed for the first time. In addition, the data given in previously published articles on the subject, due to the dynamic development of the industry, are obsolete and do not reflect the real situation.

  7. Modeling oil production based on symbolic regression

    International Nuclear Information System (INIS)

    Yang, Guangfei; Li, Xianneng; Wang, Jianliang; Lian, Lian; Ma, Tieju

    2015-01-01

    Numerous models have been proposed to forecast the future trends of oil production and almost all of them are based on some predefined assumptions with various uncertainties. In this study, we propose a novel data-driven approach that uses symbolic regression to model oil production. We validate our approach on both synthetic and real data, and the results prove that symbolic regression could effectively identify the true models beneath the oil production data and also make reliable predictions. Symbolic regression indicates that world oil production will peak in 2021, which broadly agrees with other techniques used by researchers. Our results also show that the rate of decline after the peak is almost half the rate of increase before the peak, and it takes nearly 12 years to drop 4% from the peak. These predictions are more optimistic than those in several other reports, and the smoother decline will provide the world, especially the developing countries, with more time to orchestrate mitigation plans. -- Highlights: •A data-driven approach has been shown to be effective at modeling the oil production. •The Hubbert model could be discovered automatically from data. •The peak of world oil production is predicted to appear in 2021. •The decline rate after peak is half of the increase rate before peak. •Oil production projected to decline 4% post-peak

  8. Electrochemical method applicable to treatment of wastewater from nitrotriazolone production.

    Science.gov (United States)

    Wallace, Lynne; Cronin, Michael P; Day, Anthony I; Buck, Damian P

    2009-03-15

    Laboratory studies show that electrochemical oxidation of acidic nitrotriazolone (NTO) solutions results in complete mineralization, with ammonium nitrate as the only solution product Other products (carbon dioxide, carbon monoxide, and nitrous oxide) are eliminated as gases from the working electrode. No additional chemical loading is required for the process, and electricity isthe only input The process maytherefore represent a cost-effective and environmentally friendly method of remediation for wastewater from NTO manufacture. Electrolyses were carried out at different applied voltages and at NTO concentrations of 0.01 and 0.05 mol/L, and the results indicate that a higher oxidation rate results in a greater charge passed per mole of NTO oxidized and increased production of nitrous oxide. Mechanisms are proposed on the basis of competing oxidative pathways that account for all products formed and the total charge passed during the reaction.

  9. Evaluating the potential of renewable diesel production from algae cultured on wastewater: techno-economic analysis and life cycle assessment

    Directory of Open Access Journals (Sweden)

    Ankita Juneja

    2017-03-01

    Full Text Available Algae, a renewable energy source, has an added advantage of consuming nutrients from wastewater and consequently aiding in wastewater treatment. The algae thus produced can be processed using alternative paths for conversion to fuels. However, due to high moisture content of algae, wet algae processing methods are being encouraged to avoid the dewatering cost and energy. Hydrothermal liquefaction is one such technology that converts the algae into high heating value bio-oil under high temperature and pressure. This bio-oil can be further upgraded to renewable diesel (RD which can be used in diesel powered vehicles without any modifications. The objective of this study is to evaluate the economic viability and to estimate the energy use and greenhouse gas (GHG emissions during life cycle of RD production from algae grown in wastewater using hydrothermal liquefaction. Economic analysis of RD production on commercial scale was performed using engineering process model of RD production plant with processing capacity of 60 Mgal wastewater/day, simulated in SuperPro designer. RD yields for algae were estimated as 10.18 MML/year with unit price of production as $1.75/RD. The GHG emissions during life cycle of RD production were found to be 6.2 times less than those produced for conventional diesel. Sensitivity analysis indicated a potential to reduce ethanol production cost either by using high lipid algae or increasing the plant size. The integrated economic and ecological assessment analyses are helpful in determining long-term sustainability of a product and can be used to drive energy policies in an environmentally sustainable direction.

  10. Enrichment of bio-oil after hydrothermal liquefaction (HTL) of microalgae C. vulgaris grown in wastewater: Bio-char and post HTL wastewater utilization studies.

    Science.gov (United States)

    Arun, Jayaseelan; Varshini, Padmanabhan; Prithvinath, P Kamath; Priyadarshini, Venkataramani; Gopinath, Kannappan Panchamoorthy

    2018-08-01

    In this study, bio-oil was produced through hydrothermal liquefaction (HTL) of C. vulgaris biomass cultivated in wastewater and was enriched into transportation fuels. Bio-oil yield was 29.37% wt at 300 °C, 60 min, at 15 g/200 mL biomass loading rate with 3% wt nano ZnO catalyst loading. Applying catalyst reduced oxygen and nitrogen content in bio-oil and increased its calorific value (19.6 ± 0.8 MJ/Kg). Bio-oil was enriched through liquid-liquid extraction (LLE) and higher yield was obtained at 30 °C for dichloromethane solvent (18.2% wt). Compounds of enriched oil were within the petro-diesel range (C 8 -C 21 ). Bio-char after HTL process was activated and used as adsorbent in wastewater treatment process to remove organic pollutants (COD, NO 3 , NH 3 and PO 4 ). Treated wastewater can be supplied as growth medium for microalgae cultivation in further experiments. Nearly 3-4 times the nanocatalyst can be reused in the HTL process. Copyright © 2018 Elsevier Ltd. All rights reserved.

  11. Risks and mitigation options for on-site storage of wastewater from shale gas and tight oil development

    International Nuclear Information System (INIS)

    Kuwayama, Yusuke; Roeshot, Skyler; Krupnick, Alan; Richardson, Nathan; Mares, Jan

    2017-01-01

    We provide a critical review of existing research and information regarding the sources of risk associated with on-site shale gas and tight oil wastewater storage in the United States, the gaps that exist in knowledge regarding these risks, policy and technology options for addressing the risks, and the relative merits of those options. Specifically, we (a) identify the potential risks to human and ecological health associated with on-site storage of shale gas and tight oil wastewater via a literature survey and analysis of data on wastewater spills and regulatory violations, (b) provide a detailed description of government regulations or industry actions that may mitigate these risks to human and ecological health, and (c) provide a critical review of this information to help generate progress toward concrete action to make shale gas and tight oil development more sustainable and more acceptable to a skeptical public, while keeping costs down. - Highlights: • We review current research/information on shale gas and tight oil wastewater storage. • Pit overflows, tank overfills, and liner malfunctions are common spill causes. • Tanks lead to smaller and less frequent spills than pits, but are not a magic bullet. • State regulations for on-site oil and gas wastewater storage are very heterogeneous.

  12. Oil shale mines and their realizable production

    International Nuclear Information System (INIS)

    Habicht, K.

    1994-01-01

    The production of Estonian oil shale depends on its marketing opportunities. The realizable production is a function of the oil shale price, which in turn depends on production costs. The latter are dependent on which mines are producing oil shale and on the volume of production. The purpose of the present article is to analyze which mines should operate under various realizable production scenarios and what should be their annual output so that the total cost of oil shale production (including maintenance at idle mines) is minimized. This paper is also targeted at observing the change in the average production cost per ton of oil shale depending on the realizable output. The calculations are based on data for the first four months of 1993, as collected by N. Barabaner (Estonian Academy of Sciences, Institute of Economy). The data include the total production volume and production cost from the mines of RE 'Eesti Polevkivi' (State Enterprise 'Estonian Oil Shale'). They also project expenses from mine closings in case of conservation. The latter costs were allocated among mines in direct proportion to their respective number of employees. (author)

  13. Oil? Finally, a product like the others

    International Nuclear Information System (INIS)

    Moreau Defarges, Philippe

    2006-01-01

    As oil is generally considered as a vital element for production and consumption system, without which the one who hasn't any could not live, the author examines whether oil is actually an exceptional raw product which would escape from market rules according to which everything depends on the market and work is the only source of value and power. In order to do so, he discusses whether the present oil price increase is a good or a bad news, whether this increase confirms that oil is finally a product like the others, whether it has been and is a reason for war, and whether oil will remain (if it has ever been) a major geopolitical issue or, in other words, a determining factor of alliances and antagonism

  14. Oil refinery wastewater treatment using coupled electrocoagulation and fixed film biological processes

    Science.gov (United States)

    Pérez, Laura S.; Rodriguez, Oscar M.; Reyna, Silvia; Sánchez-Salas, José Luis; Lozada, J. Daniel; Quiroz, Marco A.; Bandala, Erick R.

    2016-02-01

    Oil refinery wastewater was treated using a coupled treatment process including electrocoagulation (EC) and a fixed film aerobic bioreactor. Different variables were tested to identify the best conditions using this procedure. After EC, the effluent was treated in an aerobic biofilter. EC was capable to remove over 88% of the overall chemical oxygen demand (COD) in the wastewater under the best working conditions (6.5 V, 0.1 M NaCl, 4 electrodes without initial pH adjustment) with total petroleum hydrocarbon (TPH) removal slightly higher than 80%. Aluminum release from the electrodes to the wastewater was found an important factor for the EC efficiency and closely related with several operational factors. Application of EC allowed to increase the biodegradability of the sample from 0.015, rated as non-biodegradable, up to 0.5 widely considered as biodegradable. The effluent was further treated using an aerobic biofilter inoculated with a bacterial consortium including gram positive and gram negative strains and tested for COD and TPH removal from the EC treated effluent during 30 days. Cell count showed the typical bacteria growth starting at day three and increasing up to a maximum after eight days. After day eight, cell growth showed a plateau which agreed with the highest decrease on contaminant concentration. Final TPHs concentration was found about 600 mgL-1 after 30 days whereas COD concentration after biological treatment was as low as 933 mgL-1. The coupled EC-aerobic biofilter was capable to remove up to 98% of the total TPH amount and over 95% of the COD load in the oil refinery wastewater.

  15. Removal of colour, turbidity, oil and grease for slaughterhouse wastewater using electrocoagulation method

    Science.gov (United States)

    Yusoff, Mohd Suffian; Azwan, Azlyza Mohd; Zamri, Mohd Faiz Muaz Ahmad; Aziz, Hamidi Abdul

    2017-10-01

    In this study electrocoagulation method is used to treat slaughterhouse wastewaters. The aim of this study is to determine the efficiency of electrocoagulation method for the removal of colour, turbidity, oil and grease of slaughterhouse wastewaters. The factors of electrode types, and voltage applied during treatment are the study parameters. The types of electrode used are Aluminium (Al) grade 6082 and Iron (Fe) grade 1050. Meanwhile, the ranges of voltage applied are 2, 4, 6, 8 volts at a time interval of 10, 20 and 30 minutes respectively. The effect of these factors on the removal of fat oil and grease (FOG), colour and turbidity are analyzed. The results show maximum removal of FOG, colour and turbidity are recorded using Fe electrode at 8 V of applied voltage with 30 minutes of treatment time. The increase in treatment time of the cell will also increase the amount of hydrogen bubbles at the cathode which results in a greater upwards flux and a faster removal of FOG,, turbidity and colour. The removal of FOG, colour and turbidity are 98%, 92% and 91 % respectively. Meanwhile, by using Al electrodes in the same condition, the removal of FOG, colour and turbidity are 91%, 85% and 87 % respectively. Whereas by using Fe-Al as electrodes pairs, the removal of FOG, colour and turbidity are found to be at 90%, 87% and 76 % respectively. In this case, the Fe-Fe pair electrodes have been proven to provide better performance for FOG, colour and turbidity removals of slaughterhouse wastewaters. Therefore, it is feasible to be considered as an alternative method for wastewater treatment.

  16. SOLID BIOFUEL UTILIZATION IN VEGETABLE OIL PRODUCTION

    Directory of Open Access Journals (Sweden)

    Slusarenko V.

    2016-08-01

    Full Text Available The paper deals with questions of creating at JSC “Alimentarmash "in the last 20 years the technological equipment for the production of vegetable oils from oilseeds: from the press for the final spin to mini oilfactory, using as an energy source for heating the liquid coolant (Thermal oil "Arian" of solid biofuels - husk of sunflower seeds.

  17. Oil production from bituminous materials

    Energy Technology Data Exchange (ETDEWEB)

    Gotting, H E.B.; Gotting, L K

    1940-07-30

    The material such as shale, coal, lignite and the like, is heated in an externally heated retort and the generated gas is passed to a series of cells comprising a bubble tower, the cells of which are separated by plates, through which pipes, with perforated caps pass, also overflow pipes. The gas passing through the cell produces further oil vapour, and is decomposed by heated oil into lighter fractions, till it passes out of the tower through a pipe and through condensing coil to receiving vessels for the oil. Fixed gas passes to cylindrical wash vessels, the back pressure inducing the required pressure in the retort.

  18. Giant Oil Fields - The Highway to Oil: Giant Oil Fields and their Importance for Future Oil Production

    International Nuclear Information System (INIS)

    Robelius, Fredrik

    2007-01-01

    Since the 1950s, oil has been the dominant source of energy in the world. The cheap supply of oil has been the engine for economic growth in the western world. Since future oil demand is expected to increase, the question to what extent future production will be available is important. The belief in a soon peak production of oil is fueled by increasing oil prices. However, the reliability of the oil price as a single parameter can be questioned, as earlier times of high prices have occurred without having anything to do with a lack of oil. Instead, giant oil fields, the largest oil fields in the world, can be used as a parameter. A giant oil field contains at least 500 million barrels of recoverable oil. Only 507, or 1 % of the total number of fields, are giants. Their contribution is striking: over 60 % of the 2005 production and about 65 % of the global ultimate recoverable reserve (URR). However, giant fields are something of the past since a majority of the largest giant fields are over 50 years old and the discovery trend of less giant fields with smaller volumes is clear. A large number of the largest giant fields are found in the countries surrounding the Persian Gulf. The domination of giant fields in global oil production confirms a concept where they govern future production. A model, based on past annual production and URR, has been developed to forecast future production from giant fields. The results, in combination with forecasts on new field developments, heavy oil and oil sand, are used to predict future oil production. In all scenarios, peak oil occurs at about the same time as the giant fields peak. The worst-case scenario sees a peak in 2008 and the best-case scenario, following a 1.4 % demand growth, peaks in 2018

  19. Production and quality of fertirrgated cherry tomatoes with pisciculture wastewater

    Directory of Open Access Journals (Sweden)

    Thamires da Silva Araujo

    2017-07-01

    Full Text Available The aim of this work was to evaluate the production and the quality of fertirrigated cherry tomatoes with pisciculture wastewater with and without probiotics. The experiment was conducted in pots, under ambient conditions protected by 50% sombrite. The experimental design was a completely randomized design with four treatments and four replicates, the experimental unit consisting of thirty-two plants. Four water slides were tested: water; water from fish farms without the use of probiotics; water with probiotic and probiotic pisciculture wastewater. Probiotic addition was performed every 48 hours, with 0,5 g of probiotic containing at least 5x109 billion colony forming units per viable gram for every 8 L of water, each plant receiving 1 L of water manually in the morning. The soil used in the experiment to fill the vessels was classified as a NEOSOLO QUARTZARENIC dystrophic sandy texture caatinga stage, mixed with organic compound. The results showed that there was no difference between treatments for yield, number of fruits, fruit weight and pH. The treatment of water with probiotic was the one that presented lower acidity and better relation SST / ATT. The reuse of fish water with and without addition of the probiotic for fertirrigation of the cherry tomato crop did not interfere in the fruit production.

  20. Annealing optimization in the process of making membrane PSF19%DMFEVA2 for wastewater treatment of palm oil mill effluent

    Science.gov (United States)

    Said, A. A.; Mustafa

    2018-02-01

    A small proportion of the Palm Oil Mill Effluent (POME) treatment has used its wastewater to converted to methane gas which will then be converted again into electrical energy. However, for Palm Oil Mill whose has a value of Chemical Oxygen Demand in its wastewater is less than 60.000 mg / L this can’t so that the purpose wastewater treatment only to reach the standard that can be safe to dispose into the environment. Wastewater treatment systems that are general applied by Palm Oil Mill especially in North Sumatera are aerobic and anaerobic, this method takes a relatively long time due to very dependent on microbial activity. An alternative method for wastewater treatment offered is membrane technology because the process is much more effective, the time is relatively short, and expected to give more optimal result. The optimum membrane obtained is PSF19%DMFEVA2T75 membrane,while the parameter condition of the permeate analysis produced in the treatment of POME wastewater with membrane PSF19%DMFEVA2T75 obtained at pH = 7.0; TSS = 148 mg / L; BOD = 149 mg / L; And COD = 252 mg / L. The results obtained is accordance with the standard of the quality of POME.

  1. Growth regulators and essential oil production

    OpenAIRE

    Prins, Cláudia L; Vieira, Ivo J. C; Freitas, Silvério P

    2010-01-01

    The aroma and fragrance industry is a billion-dollar world market which grows annually. Essential oils comprise the majority of compounds used by these industries. These sets of metabolites are formed mainly by monoterpenes, which are products of the plants' secondary metabolism. Biosynthesized from mevalonate and methylerythitol phosphate, the essential oil production depends not only on genetic factors and the developmental stage of plants, but also on environmental factors which could resu...

  2. Ultrasound pretreatment for enhanced biogas production from olive mill wastewater.

    Science.gov (United States)

    Oz, Nilgun Ayman; Uzun, Alev Cagla

    2015-01-01

    This study investigates applicability of low frequency ultrasound technology to olive mill wastewaters (OMWs) as a pretreatment step prior to anaerobic batch reactors to improve biogas production and methane yield. OMWs originating from three phase processes are characterized with high organic content and complex nature. The treatment of the wastewater is problematic and alternative treatment options should be investigated. In the first part of the study, OMW samples were subjected to ultrasound at a frequency of 20kHz with applied powers varying between 50 and 100W under temperature controlled conditions for different time periods in order to determine the most effective sonication conditions. The level of organic matter solubilization at ultrasound experiments was assessed by calculating the ratio of soluble chemical oxygen demand/total chemical oxygen demand (SCOD/TCOD). The results revealed that the optimum ultrasonic condition for diluted OMW is 20kHz, 0.4W/mL for 10min. The application of ultrasound to OMW increased SCOD/TCOD ratio from 0.59 to 0.79. Statistical analysis (Friedman's tests) show that ultrasound was significantly effective on diluted OMW (p0.05). For raw OMW, this increase has been found to be limited due to high concentration of suspended solids (SS). In the second part of the study, biogas and methane production rates of anaerobic batch reactor fed with the ultrasound pretreated OMW samples were compared with the results of control reactor fed with untreated OMW in order to determine the effect of sonication. A nonparametric statistical procedure, Mann-Whitney U test, was used to compare biogas and methane production from anaerobic batch reactors for control and ultrasound pretreated samples. Results showed that application of low frequency ultrasound to OMW significantly improved both biogas and methane production in anaerobic batch reactor fed with the wastewater (pbiogas and methane compared with the untreated one (control reactor). The

  3. Biomass production and nutrient assimilation by a novel microalga, Monoraphidium spp. SDEC-17, cultivated in a high-ammonia wastewater

    International Nuclear Information System (INIS)

    Jiang, Liqun; Pei, Haiyan; Hu, Wenrong; Hou, Qingjie; Han, Fei; Nie, Changliang

    2016-01-01

    Highlights: • The algae Monoraphidium SDEC-17 was identified as a suitable feedstock for biofuel. • SDEC-17 has been domesticated to survive in high-ammonia wastewater (CW). • SDEC-17 exhibited robust growth and nutrient assimilation in CW. • CW improved protein accumulation of SDEC-17. - Abstract: To obtain suitable microalgae species for successful algal biomass production from low-cost wastewater, four axenic algae strains were isolated from a local lake. Through acclimation with the high-ammonia complex wastewater (CW) of a gourmet powder factory, one algae species showed good ability to yield biomass and endure high-ammonia conditions (>170 mg L"−"1) in CW. This was verified as a Monoraphidium spp. by molecular identification, and named as SDEC-17. The algae were 27–60 μm in length and 4–10 μm in width, with relatively low specific surface area for withstanding ammonia ingress through the cell membrane. The final biomass densities of SDEC-17 in CW (1.29 ± 0.09 g L"−"1) and BG11 medium (1.31 ± 0.08 g L"−"1) did not show a statistically significant difference (p > 0.05). Moreover, protein content was stimulated to 44% by CW, compared to 35% in BG11. Lipid accumulation of SDEC-17 was not significantly influenced by CW, and fatty acid profiles resembled those of palm oil. The algae would utilize ammonia first under conditions with various nitrogen sources present, and absorb large amounts of phosphorus from the wastewater. Thus, phosphorus and ammonia were removed with efficiencies of nearly 100%, satisfying the discharge standard of pollutants for municipal wastewater treatment plants. These results suggested that Monoraphidium spp. SDEC-17 is a promising candidate for algae biomass production and possibly chemical energy recovery from the complex wastewater.

  4. Treatment of wastewater contaminated with detergents and mineral oils using effective and scalable technology.

    Science.gov (United States)

    Abdelmoez, Wael; Barakat, Nasser A M; Moaz, Asmaa

    2013-01-01

    In this work, effective, cheap and scalable methodology is introduced to treat oily wastewater. The water produced from car-wash processes was utilized as a model because it has various pollutants - oil, lubricants, detergents, solid particles, etc. The results showed that the turbidity and chemical oxygen demand (COD) values dramatically decrease by using the proposed treatment process, which consists of coagulation, flocculation, sand filtration, and oxidation followed by sand as well as activated carbon filtration. Moreover, the operating conditions were optimized. Without adjustment of the pH value of car-wash wastewater, it was found that 200 ppm of ferric chloride, as a coagulant, and 1 ppm of potassium permanganate, as an oxidant, are the optimum doses. The COD and turbidity values of the final treated wastewater were reduced by almost 88 and 100%, respectively. A prototype with 15 L capacity was designed and fabricated to investigate the scaling up and continuity of the proposed treatment strategy. The results were very promising and indicated that the introduced methodology can be industrially applied.

  5. Investing in Iranian oil production

    International Nuclear Information System (INIS)

    Barraclough, Colin.

    1997-01-01

    The decision by a French-led consortium to sign a 2bn oil development deal with Iran represents the largest single investment in the Islamic Republic since its revolution of 1978/79. Despite the threat of US sanctions on investors, Iran is on the threshold of a major revitalization of its hydrocarbon industries. (UK)

  6. In vitro fermentation of olive oil mill wastewaters using sheep rumen liquor as inoculum: Olive mill wastewaters an alternative for ruminant's nutrition

    Directory of Open Access Journals (Sweden)

    Moufida Aggoun

    2014-12-01

    Full Text Available Olive oil mill wastewaters (OMWW are the main liquid effluents generated by the olive oil production industry. This liquid, considered pollutant and toxic, is characterised by its high content of organic matter including mainly sugars and fats, and phenols compounds, which can be used in ruminants feeding. The purpose of this study is to valorise this agricultural by-product in ruminant feeding by estimation its in vitro degradability in presence of ovine ruminale microbiota comparatively to vetch-oat hay, using in vitro gas production technique coupled with NH3-N and protozoa measurements. Cumulative gas production was recorded at 3, 6, 9, 24, 48, 72 and 96 hours of incubation. The determination of gazes produced (carbon dioxide and methane was recorded at 6, 9, 24, 48 and 96 hours. However, Ammonia and protozoa number were recorded after 24 hours of incubation. Fermentation profile was fitted to the exponential model y = a + b (1 – e-kt. The OMWW are characterized by their high sugars content (39.91% and their low content in ash (1.99% and crude protein (2.70%. This by-product is also characterized by its high concentration in total phenols (7.2% and tannins (4.5%. However, they contain a very small amount of condensed tannins (0.89%. Comparatively to vetch-oat hay, OMWW produced low amount of gas (-23.6 units. Furthermore, its in vitro fermentation generates low volume of methane (9.83%, V/V, suggesting that the OMWW nature enhanced the efficiency of ruminale microbiota towards microbial biomass production and inhibition of ruminale methanogenesis pathway. This result is reinforced by the reduction of ammonia production (-0.35 units and protozoa proliferation (-1 unit comparatively to vetch-oat hay. The anaerobic biodegradation of OMWW reveal their significant use by the rumen microbiota, allowing us to strongly recommend its use as a supplement in feed ruminant. In addition, it allows considering using this residue as a feed additive in

  7. Can algae-based technologies be an affordable green process for biofuel production and wastewater remediation?

    Science.gov (United States)

    Vo Hoang Nhat, P; Ngo, H H; Guo, W S; Chang, S W; Nguyen, D D; Nguyen, P D; Bui, X T; Zhang, X B; Guo, J B

    2018-05-01

    Algae is a well-known organism that its characteristic is prominent for biofuel production and wastewater remediation. This critical review aims to present the applicability of algae with in-depth discussion regarding three key aspects: (i) characterization of algae for its applications; (ii) the technical approaches and their strengths and drawbacks; and (iii) future perspectives of algae-based technologies. The process optimization and combinations with other chemical and biological processes have generated efficiency, in which bio-oil yield is up to 41.1%. Through life cycle assessment, algae bio-energy achieves high energy return than fossil fuel. Thus, the algae-based technologies can reasonably be considered as green approaches. Although selling price of algae bio-oil is still high (about $2 L -1 ) compared to fossil fuel's price of $1 L -1 , it is expected that the algae bio-oil's price will become acceptable in the next coming decades and potentially dominate 75% of the market. Copyright © 2018 Elsevier Ltd. All rights reserved.

  8. PRODUCTION AND CHARACTERIZATION OF BIOSURFACTANT BY Pseudomonas fluorescens USING CASSAVA FLOUR WASTEWATER AS MEDIA

    Directory of Open Access Journals (Sweden)

    Venty Suryanti

    2013-12-01

    Full Text Available Biosurfactant with efficient emulsification properties could be produced by Pseudomonas flourescens using cassava flour wastewater (manipueira as media. The ability of P. flourescens to produce biosurfactant could suggest potential use in industrial and environmental applications. Media containing a mixture of natural manipueira and nutrient broth with 48 h fermentation was the optimum condition for the biosurfactant production. Based on UV-Vis and FT-IR spectra, the biosurfactant was indicated as rhamnolipids containing hydroxyl, ester, carboxylic and aliphatic carbon chain functional groups. Biosurfactant exhibited critical micelle concentration (CMC value of 715 mg/L and reduced the surface tension of the water from 80 mN/m to 59 mN/m. The biosurfactant was able to decrease the interfacial tension about 51-70% when benzyl chloride, palm oil and kerosene were used as water-immiscible compounds. The biosurfactant was able to form stable emulsion until 30 days when paraffin, soybean oil, lubricant oil and kerosene were used as water-immiscible compounds.

  9. Chemical changes in the soil and production of oat fertilized with treated wastewater

    Directory of Open Access Journals (Sweden)

    Paulo Fortes Neto

    2013-12-01

    Full Text Available The purpose of this project was to ensure the quality and impact of the application of treated sewage wastewater on the chemical properties of Dystrophic Yellow Argisol and on biomass and grain production of white oat (Avena sativa, L. After the wastewater was chemically characterized, it was applied to the soil in concentrations of 0, 30, 60 and 90 m3 ha-1 in plots of 200 m2. Doses of water were compared with mineral fertilizer doses recommended for oat. The experimental design was a split plot with four randomized blocks. The wastewater had chemical qualities useful for grain cultivation. The values of calcium, CTC, V, pH increased and acidity potential decreased in the soil after the wastewater was applied. Doses of the wastewater provided increments in biomass production and oat grains similar to that obtained with chemical fertilizers. We conclude that wastewater can be used to correct soil acidity and replace or supplement chemical fertilizers.

  10. Integrative approach for utilization of olive mill wastewater and lebna's whey for ethanol production

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, M.A.; Hayek, B.O.; Al-Hmoud, N.; Al-Gogazeh, L.

    2009-09-15

    The industry of olive oil extraction in Jordan involves an intensive consumption of water and generates large quantities of olive mill wastewater (OMW). This wastewater has a high pollution risk with biological oxygen demand (BOD). The organic fraction of OMW includes sugars, tannins, polyphenols, polyalcohols, pectins and lipids. The presence of remarkable amounts of aromatic compounds in OMW is responsible for its phytotoxic and antimicrobial effects. The environmental problems and potential hazards caused by OMW had led olive oil producing countries to limit their discharge and to propose and develop new technologies for OMW treatments, such as physicochemical and biological treatments. In the present investigation lebna's whey a local byproduct of widely consumed local yogurt was used with OMW for ethanol production. The obtained results showed that the proteins of lebna's whey can remove substantial amounts of aromatic compounds present in OMW. This was reflected on the reduction of the intensity of black color of OMW and removal of 37% polyphenols. Moreover, the production of ethanol was ascertained in fermentation media composed of whey and in presence of various concentrations of OMW up to 20% OMW. The obtained results showed the possibility to develop a process for improvement and enhancement of ethanol production from whey and olive oil waste in mixed yeast cultures. (au)

  11. Oil and gas exploration and production

    International Nuclear Information System (INIS)

    Babusiaux, D.; Favennec, J.P.; Bauquis, P.R.; Bret-Rouzaut, N.; Guirauden, D.

    2004-01-01

    The steps that lead to the production of oil and gas are diverse, complex and costly. They are diverse, because the detection of oil and gas involves input from many specialties, ranging from geology to reservoir engineering. They are complex, as shown by the development of the job of the petroleum architect, who coordinates all the operations. They are costly, as the investments for exploration and production represent more than half of all investments in the oil and gas sector. Moreover, exploration is a risky activity, both from the technical and financial viewpoint: only one well in five produces marketable oil. Meanwhile, the areas for exploration and production are spread throughout the world. This book provides a complete overview of the stakes and challenges involved in oil and gas exploration and production. Following a historical review and a survey of the markets, the technical phases are covered, as are the evaluation of reserves, the estimation of investments and costs, the decision-making and control processes, and the accounting, legal and contractual environment for these activities. The book concludes with a discussion of the role of safety, and of environmental and ethical issues. This work, which is designed for readers concerned with the various aspects of the oil and gas upstream sector, is accessible to all. Contents: 1. Petroleum: a strategic product. 2. Oil and gas exploration and production. 3. Hydrocarbon reserves. 4. Investments and costs. 5. Legal, fiscal and contractual framework. 6. Decision-making on exploration and production. 7. Information, accounting and competition analysis. 8. Health, safety, the environment, ethics. Bibliography. Glossary. Index

  12. Alcorn wells bolster Philippines oil production

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper reports that Alcorn International Inc., Houston, is producing about 16,500 b/d of oil from West Linapacan A field in the South China Sea off the Philippines. The field's current production alone is more than fivefold the Philippines' total average oil flow of 3,000 b/d in 1991. It's part of a string of oil and gas strikes off Palawan Island that has made the region one of the hottest exploration/development plays in the Asia-Pacific theater

  13. Global Trends and Development Prospects for Oil and the Oil Products Market

    Directory of Open Access Journals (Sweden)

    Maria Dorozhkina

    2006-03-01

    Full Text Available This article discusses the important issue of the development of the global market of oil and oil products. It offers an overview of how this market was formed and its current status, classification, location and potential of countries in the oil and oil processing business. It analyzes the Ukrainian oil products market. The article discusses the shortcomings and strategic areas for the development of Ukraine’s oil transport system. It presents an optimum method for creating integration groups in order to develop the oil processing business in Ukraine for the future. The article considers the main trends and outlines development prospects for the global oil and oil products market.

  14. Evaluation of microalgae production coupled with wastewater treatment

    DEFF Research Database (Denmark)

    De Francisci, Davide; Su, Yixi; Iital, Arvo

    2018-01-01

    dilution rate was characterized for its content of lipids, proteins and pigments. The average yields of fatty acid methyl esters (FAME), protein, lutein, chlorophylls and β-carotene was 62.4 mg, 388.2 mg, 1.03 mg, 11.82 mg and 0.44 mg per gram dry biomass, respectively. Economic analysis revealed...... that potentially more than 70% of revenue was from the production of pigments, i.e. chlorophyllin (59.6%), lutein (8.9%) and β-carotene (5.0%) while reduction in discharging costs of the treated wastewaters could account for 19.6% of the revenue. Due to the low yield of FAME and the low market price of biodiesel...

  15. Fungal chitosan production from potato processing wastewater and its characterization

    International Nuclear Information System (INIS)

    Khalaf, S.A.; Khalaf, M.A.

    2005-01-01

    Potato processing wastewater (PPW) was collected and analyzed for biological oxygen demand BOD, chemical oxygen demand (COD), total suspended solids (TSS), total nitrogen and starch content. A fungal strain of Aspergillus niger treated with ultraviolet (UV) radiation was evaluated for its ability to produce chitosan from PPW. Active UV-irradiated isolate, coded A. niger UV-2, was able to reduce COD by about 86.15% with over productivity of chitosan of 1630 mgl -1 after 5 days of its cultivation in PPW. Extractable chitosan from this isolate had a degree of deacetylation of 88.4% and a molecular weight l.lxlo 5 Da. Also, the extractable chitosan at concentration 600 mgl -1 exhibited the maximum antibacterial activity compared with crab shell chitosan

  16. Oil and gas products and energy equipment

    International Nuclear Information System (INIS)

    1996-01-01

    The planned activities of the Canadian oil and gas products and energy equipment industry for 1996-1997, were presented. The sector is made up of approximately 1500 small and medium sized enterprises. The Canadian oil field manufacturing and servicing industry holds only a small 2.5% share of the world export market, but it is recognized internationally as one of the leading suppliers of advanced petroleum equipment. Their exports include specialized equipment for extracting oil sands, gathering and treatment facilities for sour gas, underbalanced drilling technologies, equipment for wells experiencing declining production rates, top motor drives, winter drilling rigs, and horizontal drilling technologies. They also offer petroleum industry software products. Most exploration and production equipment sold abroad by Canadian firms is manufactured in Canada, but there is an increasing trend toward manufacturing in the country of operation. 2 tabs

  17. Woody biomass production in a spray irrigation wastewater treatment facility in North Carolina

    International Nuclear Information System (INIS)

    Frederick, D.; Lea, R.; Milosh, R.

    1993-01-01

    Application of municipal wastewater to deciduous tree plantations offers a viable opportunity to dispose of nutrients and pollutants, while protecting water quality. Production of woody biomass for energy or pulp mill furnish, using wastewater if feasible and markets exist in may parts of the world for this biomass. Plantations of sycamore (Platanus occidentalis L.), and sweetgum (Liquidambar styraciflua L.), have been established in Edenton, North Carolina for application of municipal wastewater. Research describing the dry weight biomass following the fifth year of seedling growth is presented along with future estimates for seedling and coppice yields. Ongoing and future work for estimating nutrient assimilation and wastewater renovation are described and discussed

  18. Influence of Hydraulic Retention Time on Biogas Production from Frozen Seafood Wastewater using Decanter Cake as Anaerobic Co-digestion Material

    OpenAIRE

    Thaniya Kaosol; Narumol Sohgrathok

    2012-01-01

    In this research, an anaerobic co-digestion using decanter cake from palm oil mill industry to improve the biogas production from frozen seafood wastewater is studied using Continuously Stirred Tank Reactor (CSTR) process. The experiments were conducted in laboratory-scale. The suitable Hydraulic Retention Time (HRT) was observed in CSTR experiments with 24 hours of mixing time using the mechanical mixer. The HRT of CSTR process impacts on the efficiency of biogas production. The best perform...

  19. Factors Affecting Oil Palm Production in Ondo State of Nigeria ...

    African Journals Online (AJOL)

    The discovery of crude oil and the civil war adversely affected oil palm production in Nigeria. This has resulted in scarcity and high cost of palm products and palm oil. The study therefore investigated the factors influencing oil palm production in Ondo State, Nigeria. One hundred and fifty respondents were selected from ...

  20. Panorama 2011: Water in fuel production Oil production and refining

    International Nuclear Information System (INIS)

    Nabzar, L.

    2011-01-01

    Water plays a vital role in the production of fuels. Against a background of extremely high pressure to do with the need to protect the environment, better manage energy use and operate in a socially responsible manner - as well as the need to protect water as a resource and reduce greenhouse gas emissions, water management has become a major issue for the oil industry. These issues have all more or less been factored into the integrated water management programmes which have been introduced both in oil production and oil refining. These programmes have been designed to keep waste and emissions to a minimum, and to reduce the quantities of water required. (author)

  1. Oil and gas leasing/production program

    International Nuclear Information System (INIS)

    Heimberger, M.L.

    1992-01-01

    As the Congress declared in the Outer Continental Shelf Lands Act the natural gas and oil production from the Outer Continental Shelf constitutes an important part of the Nation's domestic energy supply. Federal offshore minerals are administered within the Department of the Interior by the Minerals Management Service (MMS), which provides access to potential new sources of natural gas and oil offshore by conducting lease sales. Each year, on or before March 31, the MMS presents to Congress a fiscal year annual report on the Federal offshore natural gas and oil leasing and production program. In FY 1991, this program was the third largest producer of non-tax revenue for the US Treasury, contributing more than $3 billion. This report presents Federal offshore leasing, sales, production, and exploration activities, and environmental monitoring activities

  2. Hydrogen production by supercritical water gasification of wastewater from food waste treatment processes

    Energy Technology Data Exchange (ETDEWEB)

    Lee, In-Gu [Korea Institute of Energy Research (Korea, Republic of)

    2010-07-01

    Korean food wastes have high moisture content (more than 85 wt%) and their major treatment processes such as drying or biological fermentations generate concentrated organic wastewater (CODs of about 100,000 mgO{sub 2}/L). For obtaining both wastewater treatment and hydrogen production from renewable resources, supercritical water gasification (SCWG) of the organic wastewater was carried out in this work. The effect of catalyst, reaction temperature, and reactor residence time on COD destruction and composition of gas products was examined. As a result, a SCWG of the wastewater over Ni- Y/activated charcoal at 700 C, 28 MPa yielded 99 % COD destruction and hydrogen-rich gas production (45 vol% H{sub 2}). A liquid-phase thermal pretreatment to destroy solid particles from the wastewater was proposed for more effective operation of the SCWG system. (orig.)

  3. Production, properties and utilisation of pyrolysis oil

    Energy Technology Data Exchange (ETDEWEB)

    Sipilae, K; Oasmaa, A; Arpiainen, V; Solantausta, Y; Leppaemaeki, E; Kuoppala, E; Levander, J; Kleemola, J; Saarimaeki, P [VTT Energy, Jyvaeskylae (Finland). Energy Production Technologies

    1997-12-01

    In this project VTT Energy co-ordinates the EU JOULE Project `Biofuel oil for power plants and boilers` supporting the development projects of Finnish enterprises, and participates in the Pyrolysis Project of IEA Bioenergy Agreement. Presently two pyrolysis devices with capacities of 150 g/h and 1 kg/h are used for the project. Hot gas filtering tests by using one ceramic candle equipment have been carried out with the 1 kg/h device for pyrolysis oil. The solids and alkali contents of the product oil were reduced clearly. Suitable conditions are being defined for continuous hot gas filtering. A PDU device of 20 kg/h is being commissioned. The main aim of the chemical characterisation of pyrolysis oil was to develop as simple a method as possible for differentiating pyrolysis oils and for finding correlations between the characteristics and behaviour of pyrolysis oils. Pyrolysis oils produced from various raw materials (hardwood, pine, straw) were analysed and compared with each other. VTT Energy participates in the pyrolysis network (EU/PYNE) of EU, the aim of which is to collect and disseminate research results of pyrolysis studies, i.e., through a journal with a wide circulation. VTT also participates in the pyrolysis activity of IEA (PYRA), the other partners being Great Britain, EU, Canada and the United States. I.e., quality criteria and improvement, occupational safety and pyrolysis kinetics are discussed in IEA/PYRA

  4. Biodiesel production using waste frying oil

    International Nuclear Information System (INIS)

    Charpe, Trupti W.; Rathod, Virendra K.

    2011-01-01

    Research highlights: → Waste sunflower frying oil is successfully converted to biodiesel using lipase as catalyst. → Various process parameters that affects the conversion of transesterification reaction such as temperature, enzyme concentration, methanol: oil ratio and solvent are optimized. → Inhibitory effect of methanol on lipase is reduced by adding methanol in three stages. → Polar solvents like n-hexane and n-heptane increases the conversion of tranesterification reaction. - Abstract: Waste sunflower frying oil is used in biodiesel production by transesterification using an enzyme as a catalyst in a batch reactor. Various microbial lipases have been used in transesterification reaction to select an optimum lipase. The effects of various parameters such as temperature, methanol:oil ratio, enzyme concentration and solvent on the conversion of methyl ester have been studied. The Pseudomonas fluorescens enzyme yielded the highest conversion. Using the P. fluorescens enzyme, the optimum conditions included a temperature of 45 deg. C, an enzyme concentration of 5% and a methanol:oil molar ratio 3:1. To avoid an inhibitory effect, the addition of methanol was performed in three stages. The conversion obtained after 24 h of reaction increased from 55.8% to 63.84% because of the stage-wise addition of methanol. The addition of a non-polar solvent result in a higher conversion compared to polar solvents. Transesterification of waste sunflower frying oil under the optimum conditions and single-stage methanol addition was compared to the refined sunflower oil.

  5. Production of Spirulina sp by utilization of wastewater from the powder type energy drinks

    Science.gov (United States)

    Sumantri, Indro; Priyambada, Ika Bagus

    2015-12-01

    Wastewater of energy drink type of powder produced when the the production equipment required cleaning treatment to produce one taste to others. These equipments washed by water, so that, it produced wastewater. It contains high organic substances and classified as high degradable due to food product. The content of wastewater is high carbon and nitrogen substances. Microalgae is an autotrophic microorganism, live without carbon presence, utilized to digest the substances in wastewater especially for nitrogen substances. Spirulina sp is the type of microalgae selected to utilize the wastewater of energy drink, the selection criteria is the size of Spirulina sp is relatively large and easy to separated from its solution. The experiment conducted by cultivate the seeding microalgae with certain nutrients until the certain volume. The synthetic wastewater obtained from one of energy drink type of powder with commercial brand as Kuku Bima Ener-G, the wastewater concentration selected under the close to the real condition of wastewater as basis of COD measurement (6 sachet/L or COD of 12.480mg/L) and aqueous concentration (1 sachet/L or COD of 2080mg/L). The batch experiments with 1L volume conducted and with variable of percent volume of wastewater added in order to observe the growth of microlagae. The response of the microalgae growth obtained by increasing the optical density of the microalgae solution and continued by calculation for the growth rate of microalgae. The result of the experiments indicated that for the aqueous concentration (1 sachet/L or COD of 2080mg/L) the optimum added of wastewater is 40 % with growrate of 0.55/day while for the concentrated wastewater (6 sachet/L or COD of 12.480mg/L), the optimum condition is 25 % wastewater added with growth rate of 0.43/day.

  6. Oil price movements and production agreements

    International Nuclear Information System (INIS)

    Mazraati, M.

    2004-01-01

    The purpose of this technical exercise is to apply econometric modelling to study the relationship between movements in the oil price and compliance by the Organization of the Petroleum Exporting Countries (OPEC) with its self-assigned production agreements, whose purpose is to bring order and stability to the international oil market. After introducing various methods of measurement of compliance, the study applies these methods to monthly data for 1995-2002 for OPEC. It then identifies the method ''over-production as a percentage of ceiling'' as the best-fitting and most accurate criterion for measuring OPEC compliance. The paper then elaborates on intervention analysis, explains the various types of intervention in detail and introduces a number of econometric models to monitor oil price movements resulting from OPEC's intervention in the oil market, along with the extent of its compliance with its agreements. On applying the models to a set of historical monthly data, the study finds that higher oil prices have been achieved when the effective level of compliance lies in the range of 94-99 per cent, and that lower oil prices have been experienced when there is less compliance and more volatility. The paper notes that the achievement of order and stability is the responsibility of all parties in an international market that is inherently volatile. (author)

  7. Optimization of biodiesel production from castor oil.

    Science.gov (United States)

    da Silva, Nivea de Lima; Maciel, Maria Regina Wolf; Batistella, César Benedito; Maciel Filho, Rubens

    2006-01-01

    The transesterification of castor oil with ethanol in the presence of sodium ethoxide as catalyst is an exceptional option for the Brazilian biodiesel production, because the castor nut is quite available in the country. Chemically, its oil contains about 90% of ricinoleic acid that gives to the oil some beneficial characteristics such as its alcohol solubility at 30 degrees C. The transesterification variables studied in this work were reaction temperature, catalyst concentration and alcohol oil molar ratio. Through a star configuration experimental design with central points, this study shows that it is possible to achieve the same conversion of esters carrying out the transesterification reaction with a smaller alcohol quantity, and a new methodology was developed to obtain high purity biodiesel.

  8. Biodegradable multifunctional oil production chemicals: Thermal polyaspartates

    International Nuclear Information System (INIS)

    Ross, R.J.; Ravenscroft, P.D.

    1996-01-01

    The paper deals with biodegradable oil production chemicals. Control of both mineral scale and corrosion with a single, environmentally acceptable material is an ambitious goal. Polyaspartate polymers represent a significant milestone in the attainment of this goal. Thermal polyaspartates (TPA) are polycarboxylate polymers derived via thermal condensation of the naturally occurring amino acid aspartic acid. These protein-like polymers are highly biodegradable and non-toxic, and are produced by an environmentally benign manufacturing process. TPAs exhibit excellent mineral scale inhibition activity and CO 2 corrosion control. Laboratory data on scale inhibition and corrosion control in the North Sea oil field production applications is presented. 8 refs., 2 figs., 6 tabs

  9. Ethoxyresorufin-O-deethylase (EROD) induction in rainbow trout exposed to diluted oil sand wastewater

    International Nuclear Information System (INIS)

    Verbeek, A.; Mackay, W.; Birkholz, D.

    1995-01-01

    Toxic industrial wastewaters, such as those from oil sands extraction, must be assessed for their potential sublethal effects before they can be safely disposed in the environment. The induction of ethoxyresorufin-O-deethylase activity was assessed as a potential bioindicator of sublethal stress in rainbow trout exposed to sublethal concentrations of oil sands tailings water. The mixed-function oxygenase system in rainbow trout responded rapidly following a definable concentration-response relationship; however, it proved to be a relatively insensitive indicator of sublethal exposure to oil sands tailings water. Increased activity and maximal induction, as a result of exposure to 0.3 and 0.6 times the LC 50 (Toxic Units), occurred rapidly within 24 hours of exposure. The linearity of the relationship between the concentration of oil sands tailings pond water and ethoxyresorufin-O-deethylase activity, expressed by the following regression equation, In EROD = 3.68 (conc.) + 3.20, had an r 2 value of 0.593. Maximal induction required 0.4--0.8 Toxic Units. The absolute level of maximal induction was only one-fifth to one-sixth of the potential induction as found in response to the positive control, 0.5 mg/kg β-naphthoflavone (i.p.). The authors also present data that suggests that the different levels of induction observed in trout exposed to tailings pond water vs those injected with 0.5 mg/kg β-naphthoflavone (i.p.) may be indicative of two different P450 isoforms, the CYP4Al isoform responding to the organic acidic surfactants in oil sands tailings pond water and the CYP1A1 isoform, the isoform generally associated with most xenobiotic transformation in fish, responding to β-naphthoflavone

  10. Production Optimization of Oil Reservoirs

    DEFF Research Database (Denmark)

    Völcker, Carsten

    with emphasis on optimal control of water ooding with the use of smartwell technology. We have implemented immiscible ow of water and oil in isothermal reservoirs with isotropic heterogenous permeability elds. We use the method of lines for solution of the partial differential equation (PDE) system that governs...... the uid ow. We discretize the the two-phase ow model spatially using the nite volume method (FVM), and we use the two point ux approximation (TPFA) and the single-point upstream (SPU) scheme for computing the uxes. We propose a new formulation of the differential equation system that arise...... as a consequence of the spatial discretization of the two-phase ow model. Upon discretization in time, the proposed equation system ensures the mass conserving property of the two-phase ow model. For the solution of the spatially discretized two-phase ow model, we develop mass conserving explicit singly diagonally...

  11. Quality and Trace Element Profile of Tunisian Olive Oils Obtained from Plants Irrigated with Treated Wastewater

    Directory of Open Access Journals (Sweden)

    Cinzia Benincasa

    2012-01-01

    Full Text Available In the present work the use of treated wastewater (TWW to irrigate olive plants was monitored. This type of water is characterized by high salinity and retains a substantial amount of trace elements, organic and metallic compounds that can be transferred into the soil and into the plants and fruits. In order to evaluate the impact of TWW on the overall quality of the oils, the time of contact of the olives with the soil has been taken into account. Multi-element data were obtained using ICP-MS. Nineteen elements (Li, B, Na, Mg, Al, K, Ca, Sc, Cr, Mn, Fe, Co, Ni, Cu, Zn, Sr, Mo, Ba and La were submitted for statistical analysis. Using analysis of variance, linear discriminant analysis and principal component analysis it was possible to differentiate between oils produced from different batches of olives whose plants received different types of water. Also, the results showed that there was correlation between the elemental and mineral composition of the water used to irrigate the olive plots and the elemental and mineral composition of the oils.

  12. Productivity improvement with green approach to palm oil factory productivity

    Science.gov (United States)

    Matondang, N.

    2018-02-01

    The palm oil factory (POF) processes fresh fruit bunches into crude palm oil (CPO) and palm kernel oil (PKO) by products in the form of liquid and solid waste. One of the solid wastes produced in POF Tanjung Kasau is empty fruit bunches of palm oil (FBPO) which have been burned completely on incinerator tubes so that potentially produces pollutants that pollute the environment. If FBPO waste is managed properly, it will improve the productivity of the company. Therefore, it is necessary to conduct a study to find out how far the increased productivity of the company can reduce their impact on the environment, if FBPO is used as raw material of liquid smoke. The productivity improvement approach is done by Green Productivity concept, by looking at three aspects: environmental, social and economical. Green Productivity aims to protect the environment simultaneously by increasing the productivity of the company. One way is to turn FBPO waste into liquid smoke product is by pyrolysis process. The results showed that turning FBPO solid waste into liquid smoke will increase productivity by 18.18%. Implementation of Green Productivity can improve productivity through the improvement of FBPO waste treatment process which has been done by perfect combustion by pyrolysis process so that waste can be minimized to create environment industry POF clean and friendly environment.

  13. Biodiesel production from Jatropha curcas oil

    Energy Technology Data Exchange (ETDEWEB)

    Jain, Siddharth; Sharma, M.P. [Alternate Hydro Energy Centre, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667 (India)

    2010-12-15

    In view of the fast depletion of fossil fuel, the search for alternative fuels has become inevitable, looking at huge demand of diesel for transportation sector, captive power generation and agricultural sector, the biodiesel is being viewed a substitute of diesel. The vegetable oils, fats, grease are the source of feedstocks for the production of biodiesel. Significant work has been reported on the kinetics of transesterification of edible vegetable oils but little work is reported on non-edible oils. Out of various non-edible oil resources, Jatropha curcas oil (JCO) is considered as future feedstocks for biodiesel production in India and limited work is reported on the kinetics of transesterification of high FFA containing oil. The present study reports a review of kinetics of biodiesel production. The paper also reveals the results of kinetics study of two-step acid-base catalyzed transesterification process carried out at pre-determined optimum temperature of 65 and 50 C for esterification and transesterification process, respectively, under the optimum condition of methanol to oil ratio of 3:7 (v/v), catalyst concentration 1% (w/w) for H{sub 2}SO{sub 4} and NaOH and 400 rpm of stirring. The yield of methyl ester (ME) has been used to study the effect of different parameters. The maximum yield of 21.2% of ME during esterification and 90.1% from transesterification of pretreated JCO has been obtained. This is the first study of its kind dealing with simplified kinetics of two-step acid-base catalyzed transesterification process carried at optimum temperature of both the steps which took about 6 h for complete conversion of TG to ME. (author)

  14. Energy balance of the lavender oil production

    Directory of Open Access Journals (Sweden)

    Osman GÖKDOĞAN

    2016-06-01

    Full Text Available This research was carried out to determine the energy input-output analysis of lavender oil production. Data from agricultural farms in Isparta province was used. Energy input was calculated as 1993.89 MJ and energy output was calculated as 2925.51 MJ. Wood energy, fresh stalked lavender flower energy, equipment energy, human labour energy, electricity energy, and water energy inputs were 54.22 %, 41.86 %, 3.40 %, 0.23 %, 0.18 %, and 0.10 % of energy inputs, respectively. In this production, it is noteworthy that wood was used as fuel in the lavender oil production distillation process as the highest input. In the energy outputs, an average of 3.10 kg lavender oil and 130 kg lavender water were extracted by processing 234 kg fresh stalked lavender flower. Energy use efficiency, specific energy, energy productivity, and net energy for lavender oil production were calculated as 1.47, 643.19 MJ kg-1, 0.002 kg MJ-1 and 931.62 MJ, respectively.

  15. Biohydrogen production from diary processing wastewater by anaerobic biofilm reactors

    Energy Technology Data Exchange (ETDEWEB)

    Rios-Gonzalez, L.J.; Moreno-Davila, I.M.; Rodriguez-Martinez, J.; Garza-Garcia, Y. [Universidad Autonoma de Coahuila, Saltillo, Coahuila (Mexico)]. E-mail: leopoldo.rios@mail.uadec.mx

    2009-09-15

    This article describes biological hydrogen production from diary wastewater via anaerobic fermentation using pretreated heat shock (100 degrees Celsius, 30 min.) and acid (pH 3.0, 24 h) treatment procedures to selectively enrich the hydrogen producing mixed consortia prior to inoculation to batch reactors. Bioreactor used for immobilization consortia was operated at mesophilic (room) temperature (20{+-}3 degrees Celsius), under acidophilic conditions (pH 4.0-4.5), HRT (2h), and a natural support for generate hydrogen producing mixed consortia biofilm: Opuntia imbricata. Reactor was initially operated with sorbitol (5g/L) for 60 days of operation. Batch tests were conducted using 20{+-}0.02g of natural support with biofilm. Batch experiments were conducted to investigate the effect of COD (2.9-21.1 g-COD/L), at initial pH of 7.0, 32{+-}1 degrees Celsius. Maximum hydrogen yield was obtained at 21.1 g-COD/L. Experiments of pH effect were conducted using the optimal substrate concentration (21.2 g-COD/L), at pH 4 to 7 and 11.32 (pH diary wastewater) ,and 32{+-}1 degrees Celsius. Experiments results indicate the optimum initial cultivation was pH 4.0, but we can consider also a stable hydrogen production at pH 11.32 (pH diary wastewater), so we can avoid to fit the pH, and use diary wastewater as it left the process of cheese manufacture. The operational pH of 4.0 is 1.5 units below that of previously reported hydrogen producing organisms. The influence of the effect of temperature were conducted using the optimal substrate concentration (21.2 g-COD/L), two pH levels: 4.0 and 11.32, and four different temperatures: 16{+-}3 degrees Celsius (room temperature), 3 C, 45{+-}1 degrees Celsius y 55{+-}1 degrees Celsius.Optimal temperature for hydrogen production from diary wastewater at pH 4.0 was 55{+-}1 degrees Celsius, and for pH 11.32 was 16{+-}3 degrees Celsius.Therefore, the results suggests biofilm reactors in a natural support like Opuntia imbricata have good potential

  16. Growing Chlorella sp. on meat processing wastewater for nutrient removal and biomass production.

    Science.gov (United States)

    Lu, Qian; Zhou, Wenguang; Min, Min; Ma, Xiaochen; Chandra, Ceria; Doan, Yen T T; Ma, Yiwei; Zheng, Hongli; Cheng, Sibo; Griffith, Richard; Chen, Paul; Chen, Chi; Urriola, Pedro E; Shurson, Gerald C; Gislerød, Hans R; Ruan, Roger

    2015-12-01

    In this work, Chlorella sp. (UM6151) was selected to treat meat processing wastewater for nutrient removal and biomass production. To balance the nutrient profile and improve biomass yield at low cost, an innovative algae cultivation model based on wastewater mixing was developed. The result showed that biomass yield (0.675-1.538 g/L) of algae grown on mixed wastewater was much higher than that on individual wastewater and artificial medium. Wastewater mixing eased the bottleneck for algae growth and contributed to the improved biomass yield. Furthermore, in mixed wastewater with sufficient nitrogen, ammonia nitrogen removal efficiencies (68.75-90.38%) and total nitrogen removal efficiencies (30.06-50.94%) were improved. Wastewater mixing also promoted the synthesis of protein in algal cells. Protein content of algae growing on mixed wastewater reached 60.87-68.65%, which is much higher than that of traditional protein source. Algae cultivation model based on wastewater mixing is an efficient and economical way to improve biomass yield. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Microbial Assisted Phyto remediation Of Palm Oil Mill Final Discharge (POMFD) Wastewater

    International Nuclear Information System (INIS)

    Mohd Faizal Hamzah; Norjan Yusof; Hasimah Alimon

    2016-01-01

    This study assesses microbial assisted phyto remediation of palm oil mill final discharge (POMFD) wastewater using three local macrophyte species: Leersia oryzoides, Pistia stratiotes and Ludwigia peploides. It was found respectively that BOD 5 , COD, NH 3 -N removal efficiencies of 84.7 %, 22.3 %, and 73.5 % were achieved for P. stratiotes; 88.1 %, 18 % and 69.2 % for L. peploides; and 86.1 %, 11.7 % and 69.3 % for L. oryzoides. The level of C, H and N in the tissue were influenced by macrophyte species and organs (p < 0.05). The bioconcentration factors (BCF) of various metals such as Mg, Ca, K, Na, Fe and Zn of the three macrophyte were 10 -1 to 10 0 with Fe being highly accumulated in roots of all the macrophyte (BCF=10 2 ). The translocation factors (TF) of most metals from root to shoot tissues were in a range of 10 -3 to 10 0 . In comparison with other metals, K was capable to be efficiently translocated from root to shoots in all the macrophyte species (TF=10 0 ). In this study, Bacillus megaterium, Pseudomonas spp. and Bacillus cereus that are usually involved in denitrification were identified in P. stratiotes, L. pepoides and L. oryzoides roots respectively. This confirms the macrophyte-microorganism interaction in remediation of POMFD wastewater. (author)

  18. ALTERNATIVE FOR PHENOL BIODEGRADATION IN OIL CONTAMINATED WASTEWATERS USING AN ADAPTED BACTERIAL BIOFILM LAYER

    Directory of Open Access Journals (Sweden)

    Maria Kopytko

    2008-12-01

    Full Text Available The project studied the biodegradation potential of phenols in an industrial wastewater from an oil field in the province of Santander, Colombia. An elevated potential was established, according to three important factors: the great abundance of microorganisms found in the wastewater and sludge samples collected, the bacterial adaptation to high phenol concentrations (10 mg/l and the elevated elimination efficiencies (up to 86% obtained in the laboratory tests. The laboratory scale treatment system, which consisted of fixed-bed bioreactors with adapted bacterial biofilm, was optimized using a 22 factorial experimental design. The selected variables, studied in their maximum and minimum level were: HRT (hydraulic retention time and the presence or absence of GAC (granular activated carbon layer. The response variable was phenol concentration. The optimum treatment conditions for low and high phenol concentrations (2.14 y 9.30 mg/l, were obtained with the presence of GAC and 18 hours of HRT. The best result for the intermediate phenol concentration (6.13 mg/l was obtained with a 24 hour HRT and the presence of GAC. Nevertheless, the presence of the GAC layer was not significantly important in terms of phenol removal. Moreover, the increase of HRT from 18 to 24 hours, showed no significant improvement in phenol removal.

  19. Molecular assessment of microbiota structure and dynamics along mixed olive oil and winery wastewaters biotreatment.

    Science.gov (United States)

    Eusébio, Ana; Tacão, Marta; Chaves, Sandra; Tenreiro, Rogério; Almeida-Vara, Elsa

    2011-07-01

    The major parcel of the degradation occurring along wastewater biotreatments is performed either by the native microbiota or by added microbial inocula. The main aim of this study was to apply two fingerprinting methods, temperature gradient gel electrophoresis (TGGE) and length heterogeneity-PCR (LH-PCR) analysis of 16S rRNA gene fragments, in order to assess the microbiota structure and dynamics during mixed olive oil and winery wastewaters aerobic biotreatment performed in a jet-loop reactor (JLR). Sequence homology analysis showed the presence of bacterial genera Gluconacetobacter, Klebsiella, Lactobacillus, Novosphingobium, Pseudomonas, Prevotella, Ralstonia, Sphingobium and Sphingomonas affiliated with five main phylogenetic groups: alpha-, beta- and gamma-Proteobacteria, Firmicutes and Bacteroidetes. LH-PCR analysis distinguished eight predominant DNA fragments correlated with the samples showing highest performance (COD removal rates of 67 up to 75%). Cluster analysis of both TGGE and LH-PCR fingerprinting profiles established five main clusters, with similarity coefficients higher than 79% (TGGE) and 62% (LH-PCR), and related with hydraulic retention time, indicating that this was the main factor responsible for the shifts in the microbiota structure. Canonical correspondence analysis revealed that changes observed on temperature and O(2) level were also responsible for shifts in microbiota composition. Community level metabolic profile analysis was used to test metabolic activities in samples. Integrated data revealed that the microbiota structure corresponds to bacterial groups with high degradative potential and good suitability for this type of effluents biotreatments.

  20. The effects of oil sands wastewater on fish resulting from exposure to sub-lethal concentrations

    International Nuclear Information System (INIS)

    Birkholz, D.A.; Goudey, J.S.; Balch, G.C.; Nelson, L.R.; MacKinnon, M.

    1995-01-01

    Rainbow trout, Oncorhynchus mykiss, were exposed to sub-lethal concentrations of oil sands wastewater in flow through laboratory experiments as well as to artificial ponds containing sub-lethal concentrations of tailings pond water and fine tails in order to study the viability of the wet landscape remediation option. Large (200--300 g) fish were used for all the exposures in this preliminary study and the following data were collected: blood cell counts, sex hormone concentrations, sexual maturation, stress protein concentrations, PAH-metabolites in bile, condition factors, liver somatic indices, mixed function oxygenase induction, PAHs in muscle, external condition and the condition of internal organs. The data obtained from this study revealed no adverse effects upon fish during extended field exposures. Given similar exposure conditions in the release waters of a wet landscape reclamation, the data suggest that there may be no adverse effects upon fish, however, longer term studies, other indicator organisms and additional chronic tests should be conducted

  1. Marine Lipids (Omega-3 Oil) - Stability of Oil and Enriched Products During Production and Storage

    DEFF Research Database (Denmark)

    Nielsen, Nina Skall

    2015-01-01

    The awareness of health benefits of marine lipids with a high content of omega-3 poly unsaturated fatty acids from fish and algae oil has led to an increased intake as oil and in products. However, these lipids are highly susceptible to lipid oxidation, which results in the formation of undesirable...... off-flavours and gives rise to unhealthy compounds such as free radicals and reactive aldehydes. Necessary prerequisites for successful development of omega-3 enriched products are that the oil used for enrichment is of a high quality and low in oxidation products and that oxidation of the lipids...

  2. Potential water resource impacts of hydraulic fracturing from unconventional oil production in the Bakken shale.

    Science.gov (United States)

    Shrestha, Namita; Chilkoor, Govinda; Wilder, Joseph; Gadhamshetty, Venkataramana; Stone, James J

    2017-01-01

    Modern drilling techniques, notably horizontal drilling and hydraulic fracturing, have enabled unconventional oil production (UOP) from the previously inaccessible Bakken Shale Formation located throughout Montana, North Dakota (ND) and the Canadian province of Saskatchewan. The majority of UOP from the Bakken shale occurs in ND, strengthening its oil industry and businesses, job market, and its gross domestic product. However, similar to UOP from other low-permeability shales, UOP from the Bakken shale can result in environmental and human health effects. For example, UOP from the ND Bakken shale generates a voluminous amount of saline wastewater including produced and flowback water that are characterized by unusual levels of total dissolved solids (350 g/L) and elevated levels of toxic and radioactive substances. Currently, 95% of the saline wastewater is piped or trucked onsite prior to disposal into Class II injection wells. Oil and gas wastewater (OGW) spills that occur during transport to injection sites can potentially result in drinking water resource contamination. This study presents a critical review of potential water resource impacts due to deterministic (freshwater withdrawals and produced water management) and probabilistic events (spills due to leaking pipelines and truck accidents) related to UOP from the Bakken shale in ND. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Bio-oil production from cotton stalk

    International Nuclear Information System (INIS)

    Zheng Jilu; Yi Weiming; Wang Nana

    2008-01-01

    Cotton stalk was fast pyrolyzed at temperatures between 480 deg. C and 530 deg. C in a fluidized bed, and the main product of bio-oil is obtained. The experimental result shows that the highest bio-oil yield of 55 wt% was obtained at 510 deg. C for cotton stalk. The chemical composition of the bio-oil acquired was analyzed by GC-MS, and its heat value, stability, miscibility and corrosion characteristics were determined. These results showed that the bio-oil obtained can be directly used as a fuel oil for combustion in a boiler or a furnace without any upgrading. Alternatively, the fuel can be refined to be used by vehicles. Furthermore, the energy performance of the pyrolysis process was analyzed. In the pyrolysis system used in our experiment, some improvements to former pyrolysis systems are done. Two screw feeders were used to prevent jamming the feeding system, and the condenser is equipped with some nozzles and a heat exchanger to cool quickly the cleaned hot gas into bio-oil

  4. Oil production and water management in Oman

    International Nuclear Information System (INIS)

    Parker, D.H.; Kuijvenhoven, C.A.T.; Waterland, R.D.; Smies, M.

    1991-01-01

    This paper describes the development of integrated (production) water management in Petroleum Development Oman. In its existing oil fields the water cut is rising rapidly and water production is expected to increase two to three times in the next 15 years. Re-injection of production water will continue to account for less than half of the volume of co-produced water. Current subsurface disposal of production water to shallow Tertiary formations is based on thorough knowledge of the local hydrogeology and does not affect potable water resources. However, in view of the expected increase in production water volume, utilization and disposal options have been re-evaluated. This review has been facilitated by recently acquired data on production water quality and by the results of research in dehydration and de-oiling technologies and of tests with production chemicals. The combined knowledge base is used to arrive at water management strategies for individual oil fields that are sound both in principle and in practice

  5. Pollutant in palm oil production process.

    Science.gov (United States)

    Hosseini, Seyed Ehsan; Abdul Wahid, Mazlan

    2015-07-01

    Palm oil mill effluent (POME) is a by-product of the palm industry and it releases large amounts of greenhouse gases (GHGs). Water systems are also contaminated by POME if it is released into nonstandard ponds or rivers where it endangers the lives of fish and water fowl. In this paper, the environmental bottlenecks faced by palm oil production were investigated by analyzing the data collected from wet extraction palm oil mills (POMs) located in Malaysia. Strategies for reducing pollution and technologies for GHG reduction from the wet extraction POMs were also proposed. Average GHG emissions produced from processing 1 ton of crude palm oil (CPO) was 1100 kg CO2eq. This amount can be reduced to 200 kg CO2eq by capturing biogases. The amount of GHG emissions from open ponds could be decreased from 225 to 25 kg CO2eq/MT CPO by covering the ponds. Installation of biogas capturing system can decrease the average of chemical oxygen demand (COD) to about 17,100 mg/L and stabilizing ponds in the final step could decrease COD to 5220 mg/L. Using a biogas capturing system allows for the reduction of COD by 80% and simultaneously using a biogas capturing system and by stabilizing ponds can mitigate COD by 96%. Other ways to reduce the pollution caused by POME, including the installation of wet scrubber vessels and increasing the performance of biogas recovery and biogas upgrading systems, are studied in this paper. Around 0.87 m3 POME is produced per 1 ton palm fruit milled. POME consists of around 2% oil, 2-4% suspended solid, 94-96% water. In palm oil mills, more than 90% of GHGs were emitted from POME. From 1 ton crude palm oil, 1100 kg CO2eq GHGs are generated, which can be reduced to 200 kg CO2eq by installation of biogas capturing equipment.

  6. Endocrine disrupting activities of surface water associated with a West Virginia oil and gas industry wastewater disposal site

    Energy Technology Data Exchange (ETDEWEB)

    Kassotis, Christopher D., E-mail: christopher.kassotis@duke.edu [Nicholas School of the Environment, Duke University, Durham, NC 27708 (United States); Iwanowicz, Luke R. [U.S. Geological Survey, Leetown Science Center, Fish Health Branch, 11649 Leetown Road, Kearneysville, WV 25430 (United States); Akob, Denise M.; Cozzarelli, Isabelle M.; Mumford, Adam C. [U.S. Geological Survey, National Research Program, 12201 Sunrise Valley Drive, MS 430, Reston, VA 20192 (United States); Orem, William H. [U.S. Geological Survey, Eastern Energy Resources Science Center, 12201 Sunrise Valley Drive, MS 956, Reston, VA 20192 (United States); Nagel, Susan C., E-mail: nagels@health.missouri.edu [Department of Obstetrics, Gynecology and Women' s Health, University of Missouri, Columbia, MO 65211 (United States)

    2016-07-01

    Currently, > 95% of end disposal of hydraulic fracturing wastewater from unconventional oil and gas operations in the US occurs via injection wells. Key data gaps exist in understanding the potential impact of underground injection on surface water quality and environmental health. The goal of this study was to assess endocrine disrupting activity in surface water at a West Virginia injection well disposal site. Water samples were collected from a background site in the area and upstream, on, and downstream of the disposal facility. Samples were solid-phase extracted, and extracts assessed for agonist and antagonist hormonal activities for five hormone receptors in mammalian and yeast reporter gene assays. Compared to reference water extracts upstream and distal to the disposal well, samples collected adjacent and downstream exhibited considerably higher antagonist activity for the estrogen, androgen, progesterone, glucocorticoid and thyroid hormone receptors. In contrast, low levels of agonist activity were measured in upstream/distal sites, and were inhibited or absent at downstream sites with significant antagonism. Concurrent analyses by partner laboratories (published separately) describe the analytical and geochemical profiling of the water; elevated conductivity as well as high sodium, chloride, strontium, and barium concentrations indicate impacts due to handling of unconventional oil and gas wastewater. Notably, antagonist activities in downstream samples were at equivalent authentic standard concentrations known to disrupt reproduction and/or development in aquatic animals. Given the widespread use of injection wells for end-disposal of hydraulic fracturing wastewater, these data raise concerns for human and animal health nearby. - Highlights: • Oil and gas wastewater disposal may increase endocrine disrupting activity in water. • Tested EDC activity in surface water near oil and gas wastewater injection site. • Water downstream had significantly

  7. Endocrine disrupting activities of surface water associated with a West Virginia oil and gas industry wastewater disposal site

    International Nuclear Information System (INIS)

    Kassotis, Christopher D.; Iwanowicz, Luke R.; Akob, Denise M.; Cozzarelli, Isabelle M.; Mumford, Adam C.; Orem, William H.; Nagel, Susan C.

    2016-01-01

    Currently, > 95% of end disposal of hydraulic fracturing wastewater from unconventional oil and gas operations in the US occurs via injection wells. Key data gaps exist in understanding the potential impact of underground injection on surface water quality and environmental health. The goal of this study was to assess endocrine disrupting activity in surface water at a West Virginia injection well disposal site. Water samples were collected from a background site in the area and upstream, on, and downstream of the disposal facility. Samples were solid-phase extracted, and extracts assessed for agonist and antagonist hormonal activities for five hormone receptors in mammalian and yeast reporter gene assays. Compared to reference water extracts upstream and distal to the disposal well, samples collected adjacent and downstream exhibited considerably higher antagonist activity for the estrogen, androgen, progesterone, glucocorticoid and thyroid hormone receptors. In contrast, low levels of agonist activity were measured in upstream/distal sites, and were inhibited or absent at downstream sites with significant antagonism. Concurrent analyses by partner laboratories (published separately) describe the analytical and geochemical profiling of the water; elevated conductivity as well as high sodium, chloride, strontium, and barium concentrations indicate impacts due to handling of unconventional oil and gas wastewater. Notably, antagonist activities in downstream samples were at equivalent authentic standard concentrations known to disrupt reproduction and/or development in aquatic animals. Given the widespread use of injection wells for end-disposal of hydraulic fracturing wastewater, these data raise concerns for human and animal health nearby. - Highlights: • Oil and gas wastewater disposal may increase endocrine disrupting activity in water. • Tested EDC activity in surface water near oil and gas wastewater injection site. • Water downstream had significantly

  8. Sustainability aspects of biobased products : comparison of different crops and products from the vegetable oil platform

    NARCIS (Netherlands)

    Meesters, K.P.H.; Corré, W.J.; Conijn, J.G.; Patel, M.K.; Bos, H.L.

    2012-01-01

    This study focusses on the production of vegetable oil based products. A limited number of aspacts of the sustainability of the full chain (from agriculture to product at the factory gate) was evaluated. Three different vegetable oils were taken into account: palm oil, soy oil and rapeseed oil. Also

  9. Ethanol production from lignocellulosic byproducts of olive oil extraction.

    Science.gov (United States)

    Ballesteros, I; Oliva, J M; Saez, F; Ballesteros, M

    2001-01-01

    The recent implementation of a new two-step centrifugation process for extracting olive oil in Spain has substantially reduced water consumption, thereby eliminating oil mill wastewater. However, a new high sugar content residue is still generated. In this work the two fractions present in the residue (olive pulp and fragmented stones) were assayed as substrate for ethanol production by the simultaneous saccharification and fermentation (SSF) process. Pretreatment of fragmented olive stones by sulfuric acid-catalyzed steam explosion was the most effective treatment for increasing enzymatic digestibility; however, a pretreatment step was not necessary to bioconvert the olive pulp into ethanol. The olive pulp and fragmented olive stones were tested by the SSF process using a fed-batch procedure. By adding the pulp three times at 24-h intervals, 76% of the theoretical SSF yield was obtained. Experiments with fed-batch pretreated olive stones provided SSF yields significantly lower than those obtained at standard SSF procedure. The preferred SSF conditions to obtain ethanol from olives stones (61% of theoretical yield) were 10% substrate and addition of cellulases at 15 filter paper units/g of substrate.

  10. Oil sand synfuel production using nuclear energy

    International Nuclear Information System (INIS)

    Barnert, H.

    1984-10-01

    The importance of oil sand as a primary energy carrier is illustrated. The oil sand mining project 'synfuel' in Fort McMurray, Alberta, Canada, is described. On the basis of a layout of an In-situ-process different possibilities of introducing nuclear energy to the process are described. This leads to an increase of the product yield, leading finally to a doubling of the energy output compared to the reference layout. The introduction of nuclear energy contributes to the reduction of emissions, in particular to the emission of carbon dioxide in the conversion process. (orig.)

  11. Effect of static magnetic field on the oxygen production of Scenedesmus obliquus cultivated in municipal wastewater.

    Science.gov (United States)

    Tu, Renjie; Jin, Wenbiao; Xi, Tingting; Yang, Qian; Han, Song-Fang; Abomohra, Abd El-Fatah

    2015-12-01

    Algal-bacterial symbiotic system, with biological synergism of physiological functions of both algae and bacteria, has been proposed for cultivation of microalgae in municipal wastewater for biomass production and wastewater treatment. The algal-bacterial symbiotic system can enhance dissolved oxygen production which enhances bacterial growth and catabolism of pollutants in wastewater. Therefore, the oxygen production efficiency of microalgae in algal-bacterial systems is considered as the key factor influencing the wastewater treatment efficiency. In the present study, we have proposed a novel approach which uses static magnetic field to enhance algal growth and oxygen production rate with low operational cost and non-toxic secondary pollution. The performance of oxygen production with the magnetic field was evaluated using Scenedesmus obliquus grown in municipal wastewater and was calculated based on the change in dissolved oxygen concentration. Results indicated that magnetic treatment stimulates both algal growth and oxygen production. Application of 1000 GS of magnetic field once at logarithmic growth phase for 0.5 h increased the chlorophyll-a content by 11.5% over the control after 6 days of growth. In addition, magnetization enhanced the oxygen production rate by 24.6% over the control. Results of the study confirmed that application of a proper magnetic field could reduce the energy consumption required for aeration during the degradation of organic matter in municipal wastewater in algal-bacterial symbiotic systems. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Mixotrophic cultivation of a microalga Scenedesmus obliquus in municipal wastewater supplemented with food wastewater and flue gas CO2 for biomass production.

    Science.gov (United States)

    Ji, Min-Kyu; Yun, Hyun-Shik; Park, Young-Tae; Kabra, Akhil N; Oh, In-Hwan; Choi, Jaeyoung

    2015-08-15

    The biomass and lipid/carbohydrate production by a green microalga Scenedesmus obliquus under mixotrophic condition using food wastewater and flue gas CO2 with municipal wastewater was investigated. Different dilution ratios (0.5-2%) of municipal wastewater with food wastewater were evaluated in the presence of 5, 10 and 14.1% CO2. The food wastewater (0.5-1%) with 10-14.1% CO2 supported the highest growth (0.42-0.44 g L(-1)), nutrient removal (21-22 mg TN L(-1)), lipid productivity (10-11 mg L(-1)day(-1)) and carbohydrate productivity (13-16 mg L(-1)day(-1)) by S. obliquus after 6 days of cultivation. Food wastewater increased the palmitic and oleic acid contents up to 8 and 6%, respectively. Thus, application of food wastewater and flue gas CO2 can be employed for enhancement of growth, lipid/carbohydrate productivity and wastewater treatment efficiency of S. obliquus under mixotrophic condition, which can lead to development of a cost effective strategy for microalgal biomass production. Copyright © 2015 Elsevier Ltd. All rights reserved.

  13. Trends in heavy oil production and refining in California

    International Nuclear Information System (INIS)

    Olsen, D.K.; Ramzel, E.B.; Pendergrass, R.A. II.

    1992-07-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production and is part of a study being conducted for the US Department of Energy. This report summarizes trends in oil production and refining in Canada. Heavy oil (10 degrees to 20 degrees API gravity) production in California has increased from 20% of the state's total oil production in the early 1940s to 70% in the late 1980s. In each of the three principal petroleum producing districts (Los Angeles Basin, Coastal Basin, and San Joaquin Valley) oil production has peaked then declined at different times throughout the past 30 years. Thermal production of heavy oil has contributed to making California the largest producer of oil by enhanced oil recovery processes in spite of low oil prices for heavy oil and stringent environmental regulation. Opening of Naval Petroleum Reserve No. 1, Elk Hills (CA) field in 1976, brought about a major new source of light oil at a time when light oil production had greatly declined. Although California is a major petroleum-consuming state, in 1989 the state used 13.3 billion gallons of gasoline or 11.5% of US demand but it contributed substantially to the Nation's energy production and refining capability. California is the recipient and refines most of Alaska's 1.7 million barrel per day oil production. With California production, Alaskan oil, and imports brought into California for refining, California has an excess of oil and refined products and is a net exporter to other states. The local surplus of oil inhibits exploitation of California heavy oil resources even though the heavy oil resources exist. Transportation, refining, and competition in the market limit full development of California heavy oil resources

  14. Characterization of CRUDE OILS and petroleum products: (i) elution ...

    African Journals Online (AJOL)

    Characterization of CRUDE OILS and petroleum products: (i) elution liquid chromatographic separation and gas chromatographic analysis of crude oils and petroleum products. E.O. Odebunmi, E.A. Ogunsakin, P.E.P. Ilukhor ...

  15. Factors affecting oil palm production in Ondo state of Nigeria

    African Journals Online (AJOL)

    sola

    ... affecting oil palm production in predominantly oil palm producing areas of Ondo state of Nigeria. ... This was because the mangrove swamp zone does not .... Research stations e.g. NIFOR. Radio .... palm production management practices.

  16. Reuse of wastewater from pulp industry for the optimization of fungal xylanase production

    Directory of Open Access Journals (Sweden)

    Geisiany Maria de Queiroz-Fernandes

    2017-05-01

    Full Text Available The production of enzymes using agro-industrial waste is a low cost alternative for the reuse of byproducts, with the subsequent impact decrease on the environment. Current analysis produced xylanase using fungus Aspergillus niger, with two types of wastewater generated during the pulp chemical bleaching phase as inducers. Xylanase was produced by submerged liquid fermentation and factorial design optimized parameters that influence production (concentration of wastewater and production period. Initial culture conditions (pH, temperature and agitation were optimized independently. Alkaline wastewater was more effective than acidic wastewater for the induction of xylanase in optimized conditions: 50% of culture medium, 7-day production, 30°C, pH 6.0 and agitation at 160 rpm. Despite different results, acidic and alkaline wastewaters induced xylanase production by A. niger when employed in concentrations lower than or equal to 50% of culture medium and in the most optimal conditions described above. Alkaline wastewater is highlighted as the most efficient for such production.

  17. Hydrogen production from rice winery wastewater in an upflow anaerobic reactor by using mixed anaerobic cultures

    Energy Technology Data Exchange (ETDEWEB)

    Hanqing Yu; Zhenhu Zhu [University of Science and Technology, Hefei, Anhui (China). School of Chemistry and Materials; Wenrong Hu [Shandong Univ., Jinan (China). School of Resources and Environmental Engineering; Haisheng Zhang [Jingzi Wine Distillery Company, Shandong (China)

    2002-12-01

    Continuous production of hydrogen from the anaerobic acidogenesis of a high-strength rice winery wastewater by a mixed bacterial flora was demonstrated. The experiment was conducted in a 3.0-l upflow reactor to investigate individual effects of hydraulic retention time (HRT) (2-24 h), chemical oxygen demand (COD) concentration in wastewater (14-36 g COD/l), pH (4.5-6.0) and temperature (20-55{sup o}C) on bio-hydrogen production from the wastewater. The biogas produced under all test conditions was composed of mostly hydrogen (53-61%) and carbon dioxide (37-45%), but contained no detectable methane. Specific hydrogen production rate increased with wastewater concentration and temperature, but with a decrease in HRT. An optimum hydrogen production rate of 9.33 lH{sub 2}/gVSSd was achieved at an HRT of 2 h, COD of 34 g/l, pH 5.5 and 55{sup o}C. The hydrogen yield was in the range of 1.37-2.14 mol/mol-hexose. In addition to acetate, propionate and butyrate, ethanol was also present in the effluent as an aqueous product. The distribution of these compounds in the effluent was more sensitive to wastewater concentration, pH and temperature, but was less sensitive to HRT. This upflow reactor was shown to be a promising biosystem for hydrogen production from high-strength wastewaters by mixed anaerobic cultures. (Author)

  18. Microalgae cultivation for bioenergy production using wastewaters from a municipal WWTP as nutritional sources.

    Science.gov (United States)

    Cho, Sunja; Lee, Nakyeong; Park, Seonghwan; Yu, Jaecheul; Luong, Thanh Thao; Oh, You-Kwan; Lee, Taeho

    2013-03-01

    In order to reduce input cost for microalgal cultivation, we investigated the feasibility of wastewater taken from a municipal WWTP in Busan, Korea as wastewater nutrients. The wastewaters used in this study were the effluent from a primary settling tank (PS), the effluent from an anaerobic digestion tank (AD), the conflux of wastewaters rejected from sludge-concentrate tanks and dewatering facilities (CR), and two combined wastewaters of AD:PS (10:90, v/v) and AD:CR (10:90, v/v). Chlorella sp. ADE5, which was isolated from the AD, was selected for the feasibility test. The highest biomass production (3.01 g-dry cell weight per liter) of the isolate was obtained with the combined wastewater ADCR, and it was 1.72 times higher than that with BG 11 medium. Interestingly, the cells cultivated with wastewater containing PS wastewater were easily separated from the culture and improved lipid content, especially oleic acid content, in their cells. Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. Electricity Production and Characterization of High-Strength Industrial Wastewaters in Microbial Fuel Cell.

    Science.gov (United States)

    Cetinkaya, Afsin Y; Ozdemir, Oguz Kaan; Demir, Ahmet; Ozkaya, Bestami

    2017-06-01

    Microbial fuel cells (MFCs) convert electrochemical energy into electrical energy immediately and have a big potential usage for the same time wastewater treatment and energy recovery via electro-active microorganisms. However, MFCs must be efficiently optimized due to its limitations such as high cost and low power production. Finding new materials to increase the cell performance and reduce cost for MFC anodes is mandatory. In the first step of this study, different inoculation sludges such as anaerobic gum industry wastewater, anaerobic brewery wastewater and anaerobic phosphate were tested, and MFC that was set up with anaerobic gum industry wastewater inoculation sludge exhibited the highest performance. In the second step of this study, various wastewaters such as chocolate industry, gum industry and slaughterhouse industry were investigated for anode bacteria sources. Several electrochemical techniques have been employed to elucidate how wastewaters affect the MFCs' performance. Among all the mentioned wastewaters, the best performance was achieved by the MFCs fed with slaughterhouse wastewater; this device produced a maximum power density of 267 mW·m -2 .

  20. Bioemulsan Production by Iranian Oil Reservoirs Microorganisms

    Directory of Open Access Journals (Sweden)

    A Amiriyan, M Mazaheri Assadi, VA Saggadian, A Noohi

    2004-10-01

    Full Text Available The biosurfactants are believed to be surface active components that are shed into the surrounding medium during the growth of the microorganisms. The oil degrading microorganism Acinetobacter calcoaceticus RAG-1 produces a poly-anionic biosurfactant, hetero-polysaccharide bioemulsifier termed as emulsan which forms and stabilizes oil-water emulsions with a variety of hydrophobic substrates. In the present paper results of the possibility of biosurfactant (Emulsan production by microorganisms isolated from Iranian oil reservoirs is presented. Fourthy three gram negative and gram positive, non fermentative, rod bacilli and coccobacilli shaped baceria were isolated from the oil wells of Bibi Hakimeh, Siri, Maroon, Ilam , East Paydar and West Paydar. Out of the isolated strains, 39 bacterial strains showed beta haemolytic activity, further screening revealed the emulsifying activity and surface tension. 11 out of 43 tested emulsifiers were identified as possible biosurfactant producers and two isolates produced large surface tension reduction, indicating the high probability of biosurfactant production. Further investigation revealed that, two gram negative, oxidase negative, aerobic and coccoid rods isolates were the best producers and hence designated as IL-1, PAY-4. Whole culture broth of isolates reduced surface tension from 68 mN /m to 30 and 29.1mN/m, respectively, and were stable during exposure to high salinity (10%NaCl and elevated temperatures(120C for 15 min .

  1. Balancing carbon/nitrogen ratio to improve nutrients removal and algal biomass production in piggery and brewery wastewaters.

    Science.gov (United States)

    Zheng, Hongli; Liu, Mingzhi; Lu, Qian; Wu, Xiaodan; Ma, Yiwei; Cheng, Yanling; Addy, Min; Liu, Yuhuan; Ruan, Roger

    2018-02-01

    To improve nutrients removal from wastewaters and enhance algal biomass production, piggery wastewater was mixed with brewery wastewaters. The results showed that it was a promising way to cultivate microalga in piggery and brewery wastewaters by balancing the carbon/nitrogen ratio. The optimal treatment condition for the mixed piggery-brewery wastewater using microalga was piggery wastewater mixed with brewery packaging wastewater by 1:5 at pH 7.0, resulting in carbon/nitrogen ratio of 7.9, with the biomass concentration of 2.85 g L -1 , and the removal of 100% ammonia, 96% of total nitrogen, 90% of total phosphorus, and 93% of chemical oxygen demand. The application of the established strategies can enhance nutrient removal efficiency of the wastewaters while reducing microalgal biomass production costs. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Oil exploration and production offshore Sakhalin Island

    Energy Technology Data Exchange (ETDEWEB)

    Reed, I.C. [Sakhalin Energy Investment Company, Yuzhno-Sakhalinsk (Russian Federation)

    2006-11-15

    The offshore oil and gas exploration that is currently taking place on Sakhalin Island was discussed, with particular reference to the status of Sakhalin Energy and the challenges facing oil and exportation from the ice covered waters of Russia's Sea of Okhotsk. Sakhalin Energy, an incorporated joint venture of a consortium of companies, completed a feasibility study for oil production off the east coast of Sakhalin Island in December 1992. Sakhalin Energy has two fields, namely the Piltun Astokhskoye and Lunskoye fields. The Piltun Astokhskoye field is currently under production via the Molikpaq platform and the Lunskoye field and northern part of Piltun Astokhskoye field are currently being developed under the Phase 2 project. Since 1999, Sakhalin Energy has been producing oil from a caisson structure drilling rig which was fitted with ice protection shielding around the waterline in order to comply with Russian requirements. Production is via an undersea pipeline to a Single Anchor Leg Mooring (SALM) unit and then to a Floating Storage and Offloading unit (FSO). A brief outline of the structure was presented along with current ice management procedures and arrangements. In order to maximize the length of the production season, ice management is used to enable an early start and a late end to production. It was noted that great care is taken to ensure that the operations in ice are carried out with consideration of the environmentally sensitive area that is home to the endangered Western Gray Whale and Stellar Sea Eagle. 3 refs., 1 tab., 7 figs.

  3. Complex use of waste in wastewater and circulating water treatment from oil in heat power stations

    Science.gov (United States)

    Nikolaeva, L. A.; Iskhakova, R. Ya.

    2017-06-01

    efficient wastewater treatment from oil as well as reduction of anthropogenic pressure on the environment and economic costs of the station for nature protection measures.

  4. Pyrolytic product characteristics of biosludge from the wastewater treatment plant of a petrochemical industry.

    Science.gov (United States)

    Lin, Kuo-Hsiung; Hsu, Hui-Tsung; Ko, Ya-Wen; Shieh, Zhu-Xin; Chiang, Hung-Lung

    2009-11-15

    Biosludge was produced from the wastewater treatment plant of a petrochemical industry. The element compositions of pyrolytic residues, CO, CO(2), NOx, SOx, total hydrocarbons and detailed volatile organic compounds of pyrolytic gas, and C, H, N, S content and compositions in biofuel were determined in this study. Generally, 75-80% water content in sludge cakes and about 65-70% weight of water vapor and volatile compounds were volatilized during the drying process. Propene, propane, 1-butene, n-butane, isobutene, toluene and benzene were the major volatile organic compounds (VOCs) of the pyrolytic gas, and the concentrations for most of the top 20 VOC species were greater than 5 ppm. C(5)-C(9) compounds contributed 60% by weight of biofuel; 4-hydroxy-4-methyl-2-pentanone was the highest species, accounting for 28-53% of biofuel at various pyrolytic temperatures. Based on the dried residues, there was 8.5-13% weight in pyrolytic residues, 62-82% weight in liquid products (water and crude oil) and 5.8-30% weight in the gas phase after pyrolytic processing at 500-800 degrees C. Finally, 1.5-2.5 wt% liquid fuel was produced after the distillation process. The pyrolytic residues could be reused, the pyrolytic liquid product could be used as a fuel after distillation, and the pyrolytic gas could be recycled in the pyrolytic process to achieve non-toxic discharge and reduce the cost of sludge disposal.

  5. Biodegradable multifunctional oil production chemicals: Thermal polyaspartates

    Energy Technology Data Exchange (ETDEWEB)

    Ross, R J [Donlar Corporation (United States); Ravenscroft, P D [BP Exploration Operating Company, (United Kingdom)

    1997-12-31

    The paper deals with biodegradable oil production chemicals. Control of both mineral scale and corrosion with a single, environmentally acceptable material is an ambitious goal. Polyaspartate polymers represent a significant milestone in the attainment of this goal. Thermal polyaspartates (TPA) are polycarboxylate polymers derived via thermal condensation of the naturally occurring amino acid aspartic acid. These protein-like polymers are highly biodegradable and non-toxic, and are produced by an environmentally benign manufacturing process. TPAs exhibit excellent mineral scale inhibition activity and CO{sub 2} corrosion control. Laboratory data on scale inhibition and corrosion control in the North Sea oil field production applications is presented. 8 refs., 2 figs., 6 tabs.

  6. Biosorption of Lead by Pseudomonas sp Isolated from Oil-Contaminated Wastewaters in Khuzestan

    Directory of Open Access Journals (Sweden)

    Seyed Mansour Meybodi

    2015-05-01

    Full Text Available Biosorption is a most effective technology for the removal of such toxic substances as heavy metals. The objective of this study was four-fold: 1 to isolate lead resistant Pseudomonas strains, 2 to determine the optimal conditions of their growth, 3 to obtain the minimum inhibitory concentration of lead, and 4 to evaluate the bioremoval of lead from culture solutions. For the purposes of this study, oil-contaminated wastewater samples were collected from Khuzestan region and transferred to laboratory where they were homogenized and serially diluted up to 10-10 with sterile saline before they were cultured in Luria Bertani agar medium containing 5ppm of lead nitrate. Resistant strains were then isolated at 37°C for 24h. The samples were subsequently cultured in Macconkey agar for isolation of appropriate gram negative strains. Biochemical tests were used to identify the bacteria, 10 strains of which were screened as lead resistant ones from all the 24 isolates. The bacterial colonies were selected and tested with different concentrations (100- 2100 ppm of lead for their resistance. The plates were then incubated at 37ºC for 24h and Mso1 was chosen from among the lead resistant colonies for further experiments. This strain showed resistance to chloramphenicol (30µg and erythromycin (15µg when subjected to the antimicrobial susceptibility test. Optimal growth conditions included a temperature of 40°C at 100 rpm and a pH level of 6 in the presence of lead by spectrophotometry at 600nm. Absorption tests showed that the Mso1 strain had a metal removal efficiency of 38.45% from an aqueous solution containing 100 ppm of lead over 24h. The results confirmed the capability of Pseudomonassp in the bioremediation of Pb-contaminated wastewaters.

  7. Algae Production from Wastewater Resources: An Engineering and Cost Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Schoenung, Susan [Longitude 122 West, Inc.; Efroymson, Rebecca Ann [ORNL

    2018-03-01

    Co-locating algae cultivation ponds near municipal wastewater (MWW) facilities provides the opportunity to make use of the nitrogen and phosphorus compounds in the wastewater as nutrient sources for the algae. This use benefits MWW facilities, the algae biomass and biofuel or bioproduct industry, and the users of streams where treated or untreated waste would be discharged. Nutrient compounds can lead to eutrophication, hypoxia, and adverse effects to some organisms if released downstream. This analysis presents an estimate of the cost savings made possible to cultivation facilities by using the nutrients from wastewater for algae growth rather than purchase of the nutrients. The analysis takes into consideration the cost of pipe transport from the wastewater facility to the algae ponds, a cost factor that has not been publicly documented in the past. The results show that the savings in nutrient costs can support a wastewater transport distance up to 10 miles for a 1000-acre-pond facility, with potential adjustments for different operating assumptions.

  8. Acid Pretreatment of Sago Wastewater for Biohydrogen Production

    Science.gov (United States)

    Illi Mohamad Puad, Noor; Rahim, Nurainin Farhan Abd; Suhaida Azmi, Azlin

    2018-03-01

    Biohydrogen has been recognized to be one of the future renewable energy sources and has the potential in solving the greenhouse effects. In this study, Enterobacter aerogenes (E. aerogenes) was used as the biohydrogen producer via dark fermentation process using sago wastewater as the substrate. However, pretreatment of sago wastewater is required since it consists of complex sugars that cannot be utilized directly by the bacteria. This study aimed to use acid pretreatment method to produce high amount of glucose from sago wastewater. Three different types of acid: sulfuric acid (H2SO4); hydrochloric acid (HCl) and nitric acid (HNO3) were screened for the best acid in producing a maximum amount of glucose. H2SO4 gave the highest amount of glucose which was 9.406 g/L. Design of experiment was done using Face-centred Central Composite Design (FCCCD) tool under Response Surface Methodology (RSM) in Design Expert 9 software. The maximum glucose (9.138 g/L) was recorded using 1 M H2SO4 at 100 °C for 60 min. A batch dark fermentation using E. aerogenes was carried out and it was found that pretreated sago wastewater gave a higher hydrogen concentration (1700 ppm) compared to the raw wastewater (410 ppm).

  9. Optimization of Jatropha curcas pure plant oil production

    NARCIS (Netherlands)

    Subroto, Erna

    2015-01-01

    The use of pure plant oils as fuel, either directly or after conversion of the oil to bio-diesel, is considered to be one of the potential contributions to the transformation of the current fossil oil based economy to a sustainable bio-based one. The production of oil producing seeds using plants

  10. Cathode recovery products of oxidation of oils

    Directory of Open Access Journals (Sweden)

    М.М. Захарчук

    2009-01-01

    Full Text Available  The article provides the review of electrochemical reduction of carbonic compounds – those that are among main oxidation of oils  hydrocarbons products. The principal possibility of ketons to alcohols  reduction is proved in practice based on the experimental data . The methodical algoritm of quantative control of the catod reduction is developed, which uses the reduction-oxidizing potentiometric titration method.

  11. A Survey on the Removal Efficiency of Fat, Oil and Grease in Shiraz Municipal Wastewater Treatment Plant

    Directory of Open Access Journals (Sweden)

    Dehghani

    2014-12-01

    Full Text Available Background Fat, oil and grease (FOG in municipal wastewater treatment plant (MWWTP caused many problems. Objectives This study aimed to determine the removal efficiency of FOG in Shiraz MWWTP. Materials and Methods The removal efficiencies of FOG in the MWWTP were studied from June 2011 to September 2011 in Shiraz (Iran. The influent and effluent wastewater samples were collected in a volume of one liter (4 samples per week and analyzed according to the standard methods. Samples are transferred to the laboratory immediately. The concentration of FOG was determined using the solvent extraction and separating funnel and then compared with the effluent standards. To analyze the data, SPSS (version 11.5, Chi-square test and t test were used. Results The results showed that the FOG amount in input raw sewage in the MWWTP from June 2011 to September 2011 was around 25.5 mg/L and the amount in treated wastewater was about 8.1 mg/L. The FOG removal efficiency in this refinery was about 70% and met the environmental standards for the discharge (less than 10 mg/L (P < 0.05. Conclusions The effluent can be discharged to surface waters or used for irrigation. In order to the FOG concentration met the effluent standards, it is very crucial to control the entrance of industrial wastewater to the municipal wastewater collection networks. Otherwise, the MWWTP should be upgraded and the special techniques used to reduce FOG.

  12. Domestic wastewater treatment and biofuel production by using microalga Scenedesmus sp. ZTY1.

    Science.gov (United States)

    Zhang, Tian-Yuan; Wu, Yin-Hu; Hu, Hong-Ying

    2014-01-01

    Cultivation of microalgae for biomass production is a promising way to dispose of wastewater and recover nutrients simultaneously. The properties of nutrient removal and biomass production in domestic wastewater of a newly isolated microalga Scenedesmus sp. ZTY1 were investigated in this study. Scenedesmus sp. ZTY1, which was isolated from a wastewater treatment plant in Beijing, grew well in both the primary and secondary effluents of a wastewater treatment plant during the 21-day cultivation, with a maximal algal density of 3.6 × 10(6) and 1.9 × 10(6) cells · mL(-1), respectively. The total phosphorus concentrations in both effluents could be efficiently removed by over 97% after the cultivation. A high removal rate (over 90%) of total nitrogen (TN) was also observed. After cultivation in primary effluent for 21 days, the lipid content of Scenedesmus sp. ZTY1 in dry weight had reached about 32.2%. The lipid and triacylglycerol (TAG) production of Scenedesmus sp. ZTY1 was increased significantly with the extension of cultivation time. The TAG production of Scenedesmus sp. ZTY1 increased from 32 mg L(-1) at 21 d to 148 mg L(-1) at 45 d in primary effluent. All the experiments were carried out in non-sterilized domestic wastewater and Scenedesmus sp. ZTY1 showed good adaptability to the domestic wastewater environment.

  13. A facile method to prepare dual-functional membrane for efficient oil removal and in situ reversible mercury ions adsorption from wastewater

    Science.gov (United States)

    Zhang, Qingdong; Liu, Na; Cao, Yingze; Zhang, Weifeng; Wei, Yen; Feng, Lin; Jiang, Lei

    2018-03-01

    In this work, a novel thiol covered polyamide (nylon 66) microfiltration membrane was fabricated by combining mussel-inspired chemistry and coupling reaction, which owns excellent dual-function that can simultaneously remove oil from water efficiently and adsorb the mercury ions contained in the wastewater reversibly. Such membrane exhibited high oil/water separation efficiency, outstanding mercury adsorption ability, and good stability. Moreover, it can be regenerated in nitric acid solution, and maintain its good adsorption performance. The as-prepared membrane showed great potentials for water purification to reduce the heavy metal ion pollution and complicated industrial oily wastewater and living wastewater.

  14. HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS

    Energy Technology Data Exchange (ETDEWEB)

    Anthony R. Kovscek; Louis M. Castanier

    2002-09-30

    The Stanford University Petroleum Research Institute (SUPRI-A) conducts a broad spectrum of research intended to help improve the recovery efficiency from difficult to produce reservoirs including heavy oil and fractured low permeability systems. Our scope of work is relevant across near-, mid-, and long-term time frames. The primary functions of the group are to conduct direction-setting research, transfer research results to industry, and educate and train students for careers in industry. Presently, research in SUPRI-A is divided into 5 main project areas. These projects and their goals include: (1) Multiphase flow and rock properties--to develop better understanding of the physics of displacement in porous media through experiment and theory. This category includes work on imbibition, flow in fractured media, and the effect of temperature on relative permeability and capillary pressure. (2) Hot fluid injection--to improve the application of nonconventional wells for enhanced oil recovery and elucidate the mechanisms of steamdrive in low permeability, fractured porous media. (3) Mechanisms of primary heavy oil recovery--to develop a mechanistic understanding of so-called ''foamy oil'' and its associated physical chemistry. (4) In-situ combustion--to evaluate the effect of different reservoir parameters on the insitu combustion process. (5) Reservoir definition--to develop and improve techniques for evaluating formation properties from production information. What follows is a report on activities for the past year. Significant progress was made in all areas.

  15. Russian crude-oil production and export still increasing

    International Nuclear Information System (INIS)

    Purho, P.

    2001-01-01

    Russian crude-oil production is still increasing. In 2000 the annual production 6.48 mb/d was about 6% higher than a year before. In 2001 the production is expected to rise near the level 7 mb/d, so the increase in production volume is fast. However, the production is still far away from the maximum level of the former Soviet Union, 12 mb/d. At the moment Russia is the second largest oil producer right after Saudi Arabia. The increase in production is based on intensified use of old oil fields caused by improved technology. The oil export of Russia far abroad in 2000 was 2.5 mb/d and near abroad into FSU countries only about 180 000 b/d. The recent export of crude-oil has been near the maximum export capacity corresponding to 2.7 mb/d. About 61 million tons of oil products were exported in 2000, and even the export of oil products is increasing. Most of this was gas oil and heavy fuel oil, but also the export of gasoline was significant. The export of oil and oil products is mainly based on shipments, but also the share of train transport is high. Nearly all the crude oil is transported west either by ships or via pipelines. The share of railway transport is only few percents. Russia will continue its own oil pumping policy despite of the appeals of OPEC for reduction of oil production. Opinion in Russia is that if the increase of production and export serves the interests of Russia, it will also be carried out. The target value for crude oil for 2002 is 22 USD per barrel. The Russian crude oil production is estimated to grow up to 7.4 - 8.4 mb/d by the year 2010

  16. Renewable and sustainable bioenergies production from palm oil mill effluent (POME): win-win strategies toward better environmental protection.

    Science.gov (United States)

    Lam, Man Kee; Lee, Keat Teong

    2011-01-01

    Palm oil industry is one of the leading agricultural industries in Malaysia with average crude palm oil production of more than 13 million tonne per year. However, production of such huge amount of crude palm oil has consequently resulted to even larger amount of palm oil mill effluent (POME). POME is a highly polluting wastewater with high chemical oxygen demand (COD) and biochemical oxygen demand (BOD) in which can caused severe pollution to the environment, typically pollution to water resources. On the other hand, POME was identified as a potential source to generate renewable bioenergies such as biomethane and biohydrogen through anaerobic digestion. In other words, a combination of wastewater treatment and renewable bioenergies production would be an added advantage to the palm oil industry. In line with the world's focus on sustainability concept, such strategy should be implemented immediately to ensure palm oil is produced in an environmental friendly and sustainable manner. This review aims to discuss various technologies to convert POME to biomethane and biohydrogen in a commercial scale. Furthermore, discussion on using POME to culture microalgae for biodiesel and bioethanol production was included in the present paper as a new remedy to utilize POME with a greater beneficial return. Copyright © 2010 Elsevier Inc. All rights reserved.

  17. Simultaneous wastewater treatment and biogas production using integrated anaerobic baffled reactor granular activated carbon from baker's yeast wastewater.

    Science.gov (United States)

    Pirsaheb, Meghdad; Mohamadi, Samira; Rahmatabadi, Sama; Hossini, Hooshyar; Motteran, Fabrício

    2017-08-30

    In this study, simultaneous degradation of organic matter and color removal from food processing industries wastewater using an integrated anaerobic baffled reactor granular activated carbon (IABRGAC) was investigated. Theretofore, effective parameters such as hydraulic retention time (HRT) and granular activated carbon (GAC) filling ratio were studied. The bioreactor was operated at 3, 4 and 5 d of HRT and GAC filling ratio of 20%, 35% and 50%. To analyze and optimize the independent operating variables, response surface methodology was applied. Operating condition was optimized for HRT (4 d) and GAC filling ratio (50%). Better COD (94.6%) and BOD (93.7%) removal efficiency occurred with loading COD of 15,000 mg/L, with diminished wastewater color around 54% and turbidity to 54 NTU. In addition, methane production, methane yielding rate (Y m ) and specific methanogenic activity (SMA) test in an integrated system were investigated. The system IABRGAC was able to generate a volumetric rate about 0.31 and 0.44 L/g COD removed d at the experimental condition. The Y m was between 0.31 and 0.44 L/g COD removed .d and SMA was between 0.13 and 0.38 g COD/g volatile suspended solid. Based on results it can be concluded that the IABRGAC to be a successful pretreatment for highstrength wastewater before discharging the final effluent to sewerage and aerobic treating processes.

  18. Bio-Refineries Bioprocess Technologies for Waste-Water Treatment, Energy and Product Valorization

    Science.gov (United States)

    Keith Cowan, A.

    2010-04-01

    Increasing pressure is being exerted on communities and nations to source energy from forms other than fossil fuels. Also, potable water is becoming a scarce resource in many parts of the world, and there remains a large divide in the demand and utilization of plant products derived from genetically modified organisms (GMOs) and non-GMOs. The most extensive user and manager of terrestrial ecosystems is agriculture which is also the de facto steward of natural resources. As stated by Miller (2008) no other industry or institution comes close to the comparative advantage held for this vital responsibility while simultaneously providing food, fiber, and other biology-based products, including energy. Since modern commercial agriculture is transitioning from the production of bulk commodities to the provision of standardized products and specific-attribute raw materials for differentiated markets, we can argue that processes such as mass cultivation of microalgae and the concept of bio-refineries be seen as part of a `new' agronomy. EBRU is currently exploring the integration of bioprocess technologies using microalgae as biocatalysts to achieve waste-water treatment, water polishing and endocrine disruptor (EDC) removal, sustainable energy production, and exploitation of the resultant biomass in agriculture as foliar fertilizer and seed coatings, and for commercial extraction of bulk commodities such as bio-oils and lecithin. This presentation will address efforts to establish a fully operational solar-driven microalgae bio-refinery for use not only in waste remediation but to transform waste and biomass to energy, fuels, and other useful materials (valorisation), with particular focus on environmental quality and sustainability goals.

  19. Reduction of nutrients, microbes, and personal care products in domestic wastewater by a benchtop electrocoagulation unit

    Science.gov (United States)

    Symonds, E. M.; Cook, M. M.; McQuaig, S. M.; Ulrich, R. M.; Schenck, R. O.; Lukasik, J. O.; van Vleet, E. S.; Breitbart, M.

    2015-03-01

    To preserve environmental and human health, improved treatment processes are needed to reduce nutrients, microbes, and emerging chemical contaminants from domestic wastewater prior to discharge into the environment. Electrocoagulation (EC) treatment is increasingly used to treat industrial wastewater; however, this technology has not yet been thoroughly assessed for its potential to reduce concentrations of nutrients, a variety of microbial surrogates, and personal care products found in domestic wastewater. This investigation's objective was to determine the efficiency of a benchtop EC unit with aluminum sacrificial electrodes to reduce concentrations of the aforementioned biological and chemical pollutants from raw and tertiary-treated domestic wastewater. EC treatment resulted in significant reductions (p < 0.05, α = 0.05) in phosphate, all microbial surrogates, and several personal care products from raw and tertiary-treated domestic wastewater. When wastewater was augmented with microbial surrogates representing bacterial, viral, and protozoan pathogens to measure the extent of reduction, EC treatment resulted in up to 7-log10 reduction of microbial surrogates. Future pilot and full-scale investigations are needed to optimize EC treatment for the following: reducing nitrogen species, personal care products, and energy consumption; elucidating the mechanisms behind microbial reductions; and performing life cycle analyses to determine the appropriateness of implementation.

  20. Production of a High Efficiency Microbial Flocculant by Proteus mirabilis TJ-1 Using Compound Organic Wastewater

    Science.gov (United States)

    Zhang, Zhiqiang; Xia, Siqing; Zhang, Jiao

    2010-11-01

    The production of a high efficiency microbial flocculant (MBF) by Proteus mirabilis TJ-1 using compound organic wastewater was investigated. To cut down the cost of the MBF production, several nutritive organic wastewaters were selected to replace glucose and peptone as the carbon source and the nitrogen source in the optimized medium of strain TJ-1, respectively. The compound wastewater of the milk candy and the soybean milk was found to be good carbon source and nitrogen source for this strain to produce MBF. The cost-effective culture medium consists of (per liter): 800 mL wastewater of milk candy, 200 mL wastewater of soybean milk, 0.3 g MgSO4ṡ7 H2O, 5 g K2HPO4, 2 g and KH2PO4, pH 7.0. The economic cost for the MBF production can be cut down over a half by using the developed culture medium. Furthermore, the utilization of the two wastewaters in the preparation of culture medium of strain TJ-1 can not only save their big treatment cost, but also realize their resource reuse.

  1. Potential Development Essential Oil Production of Central Java, Indonesia

    Science.gov (United States)

    Alighiri, D.; Eden, W. T.; Supardi, K. I.; Masturi; Purwinarko, A.

    2017-04-01

    Indonesia is the source of raw essential oil in the world. Essential oils are used in various types of industries such as food and beverage, flavour, fragrance, perfumery, pharmaceuticals, and cosmetics. However, the development of Indonesian essential oil industry has not been encouraging for the production of essential oils, further it is unable to meet global demand. Besides that, the quality of volatile oil resulted cannot meet the international market standards. Based on the facts, the potential of Indonesian essential oils needs to be developed to provide added value, through increased production, improved quality and product diversification. One part of Indonesia having abundant of raw essential oil source is Central Java. Central Java has the quite large potential production of essential oils. Some essential oils produced from refining industry owned by the government, private and community sectors include cananga oils (Boyolali district), clove oils (Semarang district), patchouli oils (Brebes district, Pemalang district, and Klaten district). The main problem in the development of plants industries that producing essential oil in Central Java is low crops production, farming properties, quality of essential oils are diverse, providing poor-quality products and volatile oil price fluctuations. Marketing constraints of Central Java essential oils are quite complex supply chain. In general, marketing constraints of essential oils due to three factors, namely the low quality due to type of essential oil business that generally shaped small businesses with different capital and technology, domestic marketing is still a buyer-market (price determined by the buyer) because of weak bargaining position processors businessman, and prices fluctuate (domestic and foreign) due to uncontrolled domestic production and inter-country competition among manufacturers.

  2. Recycling the Wastewater from Swine Farm for Soilless Culture Production

    International Nuclear Information System (INIS)

    Piadang, Nattayana; Vasanaand, Nimnuan; Intaravichai, Pantipa; Chattay, Patchariya; Thipvisaid Na Tawan

    2006-09-01

    Swine farm wastewater was used in solution for hydroponics. The solution comprised swine farm wastewater influent and chemical nutrients. Water spinaches were selected for planting in foam containers. The sizes of the container were 50 x 42 x 16 centimeters. In this experiment, the ratios of influent and chemical nutrient solution were 3:1 and 1:1. The result shows that the growth of water spinaches from both solutions are almost the same. The weight of them is 78.3 and 77.3 grams each, respectively. Consequently, the result was expanded to the experiment in the field. The solution comprised swine farm wastewater influent and chemical nutrients at the ratio 1:1 was used for planting 6 kinds of vegetables. They were planted in the area of 7.2 x 2.0 meters. it was found that the weight of Chinese cabbage and Chinese white cabbage are highly significant difference when growing in chemical nutrient solution compared with growing in the solution of wastewater influent and chemical nutrient at the ratio 1:1. Moreover, water spinaches which planted in chemical nutrient solution gave the significant difference while 3 kinds of as lads gave no significant difference.

  3. Potential of wastewater grown algae for biodiesel production and CO

    African Journals Online (AJOL)

    Algae have been proposed as a potential renewable fuel source. Photosynthetic CO2 fixation to substrates that can be converted to biodiesel by microalgae is thought to be a feasible technology with energy-saving and environment-friendly approach. In the present study, potential of microalgae, from wastewater ...

  4. Experimentation on the anaerobic filter reactor for biogas production using rural domestic wastewater

    Science.gov (United States)

    Leju Celestino Ladu, John; Lü, Xi-wu; Zhong, Zhaoping

    2017-08-01

    The biogas production from anaerobic filter (AF) reactor was experimented in Taihu Lake Environmental Engineering Research Center of Southeast University, Wuxi, China. Two rounds of experimental operations were conducted in a laboratory scale at different Hydraulic retention time (HRT) and wastewater temperature. The biogas production rate during the experimentation was in the range of 4.63 to 11.78 L/d. In the first experimentation, the average gas production rate was 10.08 L/d, and in the second experimentation, the average gas production rate was 4.97 L/d. The experimentation observed the favorable Hydraulic Retention Time and wastewater temperature in AF was three days and 30.95°C which produced the gas concentration of 11.78 L/d. The HRT and wastewater temperature affected the efficiency of the AF process on the organic matter removal and nutrients removal as well. It can be deduced from the obtained results that HRT and wastewater temperature directly affects the efficiency of the AF reactor in biogas production. In conclusion, anaerobic filter treatment of organic matter substrates from the rural domestic wastewater increases the efficiency of the AF reactor on biogas production and gives a number of benefits for the management of organic wastes as well as reduction in water pollution. Hence, the operation of the AF reactor in rural domestic wastewater treatment can play an important element for corporate economy of the biogas plant, socio-economic aspects and in the development of effective and feasible concepts for wastewater management, especially for people in rural low-income areas.

  5. Production of polyol oils from soybean oil by bioprocess and Philippines edible medicinal wild mushrooms

    Science.gov (United States)

    We have been trying to develop a bioprocess for the production of polyol oils directly from soybean oil. We reported earlier the polyol products produced from soybean oil by Acinetobacter haemolyticus A01-35 (NRRL B-59985) (Hou and Lin, 2013). The objective of this study is to identify the chemical ...

  6. Production of polyol oils from soybean oil by Pseudomonas aeruginosa E03-12.

    Science.gov (United States)

    Soy-polyols are important starting materials for the manufacture of polymers such as polyurethane. We have been trying to develop a bioprocess for the production of polyol oils directly from soybean oil. We reported earlier the polyol products produced from soybean oil by Acinetobacter haemolyticus ...

  7. Environmental and Human Health Impacts of Spreading Oil and Gas Wastewater on Roads.

    Science.gov (United States)

    Tasker, T L; Burgos, W D; Piotrowski, P; Castillo-Meza, L; Blewett, T A; Ganow, K B; Stallworth, A; Delompré, P L M; Goss, G G; Fowler, L B; Vanden Heuvel, J P; Dorman, F; Warner, N R

    2018-06-19

    Thirteen states in the United States allow the spreading of O&G wastewaters on roads for deicing or dust suppression. In this study, the potential environmental and human health impacts of this practice are evaluated. Analyses of O&G wastewaters spread on roads in the northeastern, U.S. show that these wastewaters have salt, radioactivity, and organic contaminant concentrations often many times above drinking water standards. Bioassays also indicated that these wastewaters contain organic micropollutants that affected signaling pathways consistent with xenobiotic metabolism and caused toxicity to aquatic organisms like Daphnia magna. The potential toxicity of these wastewaters is a concern as lab experiments demonstrated that nearly all of the metals from these wastewaters leach from roads after rain events, likely reaching ground and surface water. Release of a known carcinogen (e.g., radium) from roads treated with O&G wastewaters has been largely ignored. In Pennsylvania from 2008 to 2014, spreading O&G wastewater on roads released over 4 times more radium to the environment (320 millicuries) than O&G wastewater treatment facilities and 200 times more radium than spill events. Currently, state-by-state regulations do not require radium analyses prior to treating roads with O&G wastewaters. Methods for reducing the potential impacts of spreading O&G wastewaters on roads are discussed.

  8. Microalgae for third generation biofuel production, mitigation of greenhouse gas emissions and wastewater treatment: Present and future perspectives – A mini review

    International Nuclear Information System (INIS)

    Maity, Jyoti Prakash; Bundschuh, Jochen; Chen, Chien-Yen; Bhattacharya, Prosun

    2014-01-01

    The extensive use of fossil fuels is increasingly recognized as unsustainable as a consequence of depletion of supplies and the contribution of these fuels to climate change by GHG (greenhouse gas) emissions into the atmosphere. Microalgae indicate alternative renewable sustainable energy sources as they have a high potential for producing large amounts of biomass which in turn can be used for production of different third-generation biofuels at large scale. Microalgae transform the solar energy into the carbon storage products, leads to lipid accumulation, including TAG (triacylglycerols), which then can be transformed into biodiesel, bioethanol and biomethanol. This paper reviews the selection, production and accumulation of target bioenergy carrier's strains and their advantages as well as the technological development for oil, biodiesel, ethanol, methanol, biogas production and GHG mitigation. The feedstock of promising algal strain exhibits the suitable biofuel production. The current progress of hybrid-technologies (biomass production, wastewater treatment, GHG mitigation) for production of prime-products as biofuels offer atmospheric pollution control such as the reduction of GHG (CO 2 fixation) coupling wastewater treatment with microalgae growth. The selection of efficient strain, microbial metabolism, cultivation systems, biomass production are key parameters of viable technology for microalgae-based biodiesel-production. - Highlights: • Microalgae are promising feedstock for biofuel production within lower farming area. • Production rate (L/ha) of oil from microalgae is much higher than other feedstock. • Lipid of Chlorella emersonii, Botryococcus braunii, Dunaliella tertiolecta, are high (>60% of dw biomass). • Remove pollutant from wastewater during feedstock production by selective strains. • Ecofriendly route to mitigate GHG (greenhouse gas) and water pollution during microalgae production

  9. Statistical modelling of Fat, Oil and Grease (FOG) deposits in wastewater pump sumps.

    Science.gov (United States)

    Nieuwenhuis, Eva; Post, Johan; Duinmeijer, Alex; Langeveld, Jeroen; Clemens, François

    2018-05-15

    The accumulation of FOG (Fat, Oil and Grease) deposits in sewer pumping stations results in an increase in maintenance costs, malfunctioning of pumps and, a potential increase of wastewater spills in receiving open water bodies. It is thought that a variety of parameters (e.g. geometry of the pump sump, pump operation, socioeconomic parameters of the catchment) influences the built-up of FOG. Based on a database containing data of 126 pumping stations located in five Dutch municipalities a statistical model was built. It is shown that 3 parameters are most significant in explaining the occurrence of FOG deposits: mean income of the population in a catchment, the amount of energy (kinetic and potential) per m 3 per day and the density of restaurants, bars and hotels in a catchment. Further it is shown that there are significant differences between municipalities that can be traced back to the local 'design paradigm'. For example, in Amsterdam, the design philosophy of discharging in the pump sump under the water surface (and hence maintaining a low level of turbulence in the pump sump) results in an increase of the probability of the formation of FOG. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

  10. Economic Analysis of Production of Essential Oil using Steam ...

    African Journals Online (AJOL)

    acer

    Economic Analysis of Production of Essential Oil using. Steam Distillation ... The return on investment (ROI) was 125%, internal rate of return ... oils, over dependency on petrodollar and ... The steam may be obtained from external boiler or.

  11. Palm oil based polyols for acrylated polyurethane production

    International Nuclear Information System (INIS)

    Rida Tajau; Mohd Hilmi Mahmood; Mek Zah Salleh; Khairul Zaman Mohd Dahlan; Rosley Che Ismail

    2006-01-01

    Palm oil becomes important renewable resources for the production of polyols for the polyurethane manufacturing industry. The main raw materials used for the production of acrylated polyurethane are polyols, isocyanates and hydroxyl terminated acrylate compounds. In these studies, polyurethane based natural polymer (palm oil), i.e., POBUA (Palm Oil Based Urethane Acrylate) were prepared from three different types of palm oil based polyols i.e., epoxidised palm oil (EPOP), palm oil oleic acid and refined, bleached and deodorized (RBD) palm olein based polyols. The performances of these three acrylated polyurethanes when used for coatings and adhesives were determined and compared with each other. (Author)

  12. The effects of the natural coagulant Moringa oleifera and alum in wastewater treatment at the Bandar Abbas Oil Refinery

    Directory of Open Access Journals (Sweden)

    Mohsen Dehghani

    2016-11-01

    Full Text Available Background: The refining process generates large volumes of wastewater containing a variety of chemical contaminants. The use of natural substitutes in treating wastewater which have fewer harmful effects is considered an effective step towards protecting the environment and sustaining the development of these industries. This study focused on the use of Moringa oleifera and alum at the Wastewater Unit at Bandar Abbas Refinery. Methods: This study was performed in 2014 in a laboratory using jar apparatus. These experiments were conducted in batch system and effective parameters including pH, coagulant dose and contact time were investigated on the wastewater obtained from Bandar Abbas Oil Refinery. Results: The jar test experiment showed that M. oleifera at 70 mg/L, optimum temperature, pH, and mixing speed could remove 38.60% of chemical oxygen demand (COD, 63.70% of turbidity, and 62.05% of total suspended solids (TSS. Also, alum at 40 mg/L removed COD, turbidity, and TSS by 51.72%, 92.16%, and 85.26% respectively from the refinery wastewater. Moreover, when M. oleifera and alum was used together with a 2:1 dosage ratio (alum at 80 mg/L and M. oleifera at 70 mg/L, they will remove COD, turbidity, and TSS by up to 50.41%, 86.14%, and 81.52% respectively. Conclusion: The use of M. oleifera as a natural coagulant is important in treating refinery wastewater not only from an environmental but also an economic point of view.

  13. Bioelectrochemical systems (BES) for sustainable energy production and product recovery from organic wastes and industrial wastewaters

    DEFF Research Database (Denmark)

    Pant, Deepak; Singh, Anoop; Van Bogaert, Gilbert

    2012-01-01

    Bioelectrochemical systems (BESs) are unique systems capable of converting the chemical energy of organic waste including low-strength wastewaters and lignocellulosic biomass into electricity or hydrogen/chemical products in microbial fuel cells (MFCs) or microbial electrolysis cells (MECs......) respectively, or other products formed at the cathode by an electrochemical reduction process. As compared to conventional fuel cells, BESs operate under relatively mild conditions, use a wide variety of organic substrates and mostly do not use expensive precious metals as catalysts. The recently discovered...... use of BES for product synthesis via microbial electrosynthesis have greatly expanded the horizon for these systems. Newer concepts in application as well as development of alternative materials for electrodes, separators, and catalysts, along with innovative designs have made BESs very promising...

  14. Corruption and reduced oil production: An additional resource curse factor?

    International Nuclear Information System (INIS)

    Al-Kasim, Farouk; Søreide, Tina; Williams, Aled

    2013-01-01

    Prominent contributions to the resource curse literature suggest weak governance and corruption are important factors behind the wide welfare variations observed among oil producing countries. How weak governance and corruption influence revenue management and expenditure decisions, as well as the possible welfare benefits derived from oil, are broadly discussed. How they impact upon volumes of oil produced has, however, attracted little attention. This paper combines a review of the resource curse and oil production literatures with findings from qualitative interviews with oil sector experts to appreciate the feasibility of connections between corruption and oil production below its potential. We make particular reference to environments where regulatory institutions or political accountability are weak and focus primarily on producer government and oil firm relations. Drawing on insights from geology, political science and economics, we suggest suboptimal production solutions can impact volumes of oil actually produced and create constraints on long term revenues for oil producing countries. We argue greater disclosure of information on oil production efficiency on a field-by-field and country-by-country basis will assist further investigation of the relationships between corruption and volumes of oil produced. - Highlights: ► We combine a literature review with qualitative interviews with oil experts. ► We focus on feasible connections between corruption and oil production levels. ► We suggest suboptimal production solutions can impact volumes of oil produced. ► Corruption may reinforce suboptimal oil production. ► More data on oil production efficiency by field and country will assist research

  15. Production of top quality soybean oil

    Directory of Open Access Journals (Sweden)

    Moustafa, Dr. Ahmad

    1995-12-01

    Full Text Available The paper comments the most adequate conditions required to produce to quality soybean oil. It is essential to avoid contaminations (water, metallic, oxidation products, overheating, undue exposition to air, as well as an appropriate control of the different steps of the refining process.

    El trabajo presenta las condiciones recomendadas para obtener aceite de soja de la mejor calidad. Es importante evitar las contaminaciones (agua, metales y compuestos oxidados, los sobrecalentamientos, la exposición al aire, así como el adecuado control de los diferentes pasos del proceso de refinación.

  16. A comprehensive overview on light independent fermentative hydrogen production from wastewater feedstock and possible integrative options

    International Nuclear Information System (INIS)

    Kumar, Gopalakrishnan; Sivagurunathan, Periyasamy; Pugazhendhi, Arivalagan; Thi, Ngoc Bao Dung; Zhen, Guangyin; Chandrasekhar, Kuppam; Kadier, Abudukeremu

    2017-01-01

    Highlights: • Hydrogen production from various wastewaters has been reviewed. • Physico-chemical composition of the wastewater influences the H_2 yield. • Sugar rich wastewaters could be a feasible source for dark fermentative H_2 production. - Abstract: This review focuses on the current developments and new insights in the field of dark fermentation technologies using wastewater as carbon and nutrient source. It has begun with the type of wastewaters (sugar rich, toxic and industrial) employed in the H_2 production and their production performances with pure (or) mixed microbiota as seeding source in the batch reactors. Secondly, well-documented continuous system performances and their failure reasons were examined along with the enhancement possibilities in ways of strategies. A SWOT analysis has been performed to validate the strength and weakness of the continuous systems towards its industrialization and possible scheme of the integration methods have been illustrated. Additionally, an outlook has been provided with enlightening the remedies for its success. Moreover, the practical perspectives of the continuous systems are highlighted and challenges towards scale up are mentioned. Finally, the possible integrative approaches along with continuous systems towards the bioH_2 technologies implementation are enlightened.

  17. Opportunities for woody crop production using treated wastewater in Egypt

    Science.gov (United States)

    R.S. Zalesny; S.R.  Evett; N.F. Kandil; C.  Soriano; John Stanturf

    2011-01-01

    The Nile River provides nearly 97% of Egypt’s freshwater supply. Egypt’s share of Nile waters is fixed at 55.5 billion cubic meters annually. As a result, Egypt will not be able to meet increasing water demand using freshwater from the Nile and has been developing non-conventional wastewater reuse strategies to meet future demands. The USAID Mission in Cairo began...

  18. An overview of empty fruit bunch from oil palm as feedstock for bio-oil production

    International Nuclear Information System (INIS)

    Chang, Siu Hua

    2014-01-01

    Empty fruit bunch (EFB) from oil palm is one of the potential biomass to produce biofuels like bio-oil due to its abundant supply and favorable physicochemical characteristics. Confirming the assertion, this paper presents an overview of EFB as a feedstock for bio-oil production. The fundamental characteristics of EFB in terms of proximate analysis, ultimate analysis and chemical composition, as well as the recent advances in EFB conversion processes for bio-oil production like pyrolysis and solvolysis are outlined and discussed. A comparison of properties in terms of proximate analysis, ultimate analysis and fuel properties between the bio-oil from EFB and petroleum fuel oil is included. The major challenges and future prospects towards the utilization of EFB as a useful resource for bio-oil production are also addressed. - Highlights: • Palm EFB has high heating value and low greenhouse gas emissions during combustion. • Conversion of EFB to bio-oil is mainly by fast pyrolysis without and with catalyst. • Bio-oil from EFB is lower in heating value, heavier and more acidic than fuel oil. • The viscosity of bio-oil from EFB is between those of light and heavy fuel oils. • The flash and pour points of bio-oil from EFB are close to those of light fuel oil

  19. Optimization of aeration for biodiesel production by Scenedesmus obliquus grown in municipal wastewater.

    Science.gov (United States)

    Han, Song-Fang; Jin, Wenbiao; Tu, Renjie; Abomohra, Abd El-Fatah; Wang, Zhi-Han

    2016-07-01

    Despite the significant breakthroughs in research on microalgae as a feedstock for biodiesel, its production cost is still much higher than that of fossil diesel. One possible solution to overcome this problem is to optimize algal growth and lipid production in wastewater. The present study examines the optimization of pretreatment of municipal wastewater and aeration conditions in order to enhance the lipid productivity of Scenedesmus obliquus. Results showed that no significant differences were recorded in lipid productivity of S. obliquus grown in primary settled or sterilized municipal wastewater; however, ultrasound pretreatment of wastewater significantly decreased the lipid production. Whereas, aeration rates of 0.2 vvm significantly increased lipid content by 51 %, with respect to the non-aerated culture, which resulted in maximum lipid productivity (32.5 mg L(-1) day(-1)). Furthermore, aeration enrichment by 2 % CO2 resulted in increase of lipid productivity by 46 % over the CO2 non-enriched aerated culture. Fatty acid profile showed that optimized aeration significantly enhanced monounsaturated fatty acid production, composed mainly of C18:1, by 1.8 times over the non-aerated S. obliquus culture with insignificant changes in polyunsaturated fatty acid proportion; suggesting better biodiesel characteristics for the optimized culture.

  20. Endocrine disrupting activities of surface water associated with a West Virginia oil and gas industry wastewater disposal site

    Science.gov (United States)

    Kassotis, Christopher D.; Iwanowicz, Luke R.; Akob, Denise M.; Cozzarelli, Isabelle M.; Mumford, Adam; Orem, William H.; Nagel, Susan C.

    2016-01-01

    Currently, >95% of end disposal of hydraulic fracturing wastewater from unconventional oil and gas operations in the US occurs via injection wells. Key data gaps exist in understanding the potential impact of underground injection on surface water quality and environmental health. The goal of this study was to assess endocrine disrupting activity in surface water at a West Virginia injection well disposal site. Water samples were collected from a background site in the area and upstream, on, and downstream of the disposal facility. Samples were solid-phase extracted, and extracts assessed for agonist and antagonist hormonal activities for five hormone receptors in mammalian and yeast reporter gene assays. Compared to reference water extracts upstream and distal to the disposal well, samples collected adjacent and downstream exhibited considerably higher antagonist activity for the estrogen, androgen, progesterone, glucocorticoid and thyroid hormone receptors. In contrast, low levels of agonist activity were measured in upstream/distal sites, and were inhibited or absent at downstream sites with significant antagonism. Concurrent analyses by partner laboratories (published separately) describe the analytical and geochemical profiling of the water; elevated conductivity as well as high sodium, chloride, strontium, and barium concentrations indicate impacts due to handling of unconventional oil and gas wastewater. Notably, antagonist activities in downstream samples were at equivalent authentic standard concentrations known to disrupt reproduction and/or development in aquatic animals. Given the widespread use of injection wells for end-disposal of hydraulic fracturing wastewater, these data raise concerns for human and animal health nearby.

  1. Continued slide seen for C.I.S. oil production

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper reports that oil production in the Commonwealth of Independent States may dip to 7.7 million b/d next year. Robert Ebel of the Center for strategic and International Studies, Washington, D.C., made that prediction before a meeting of the National Association of Petroleum Investment Analysts. Oil and Gas Journal's latest worldwide oil production figures peg the C.I.S. volume at 8.689 million b/d last August. Ebel said a September decree will allow oil prices to move in line with the market and with costs of production. That in turn will lead to development of a deregulated domestic oil market

  2. Molasses wastewater treatment and lipid production at low temperature conditions by a microalgal mutant Scenedesmus sp. Z-4

    OpenAIRE

    Ma, Chao; Wen, Hanquan; Xing, Defeng; Pei, Xuanyuan; Zhu, Jiani; Ren, Nanqi; Liu, Bingfeng

    2017-01-01

    Background Simultaneous wastewater treatment and lipid production by oleaginous microalgae show great potential to alleviate energy shortage and environmental pollution, because they exhibit tremendous advantages over traditional activated sludge. Currently, most research on wastewater treatment by microalgal are carried out at optimized temperature conditions (25?35??C), but no information about simultaneous wastewater treatment and lipid production by microalgae at low temperatures has been...

  3. Biodiesel production from Scenedesmus bijuga grown in anaerobically digested food wastewater effluent.

    Science.gov (United States)

    Shin, Dong Yun; Cho, Hyun Uk; Utomo, Joseph Christian; Choi, Yun-Nam; Xu, Xu; Park, Jong Moon

    2015-05-01

    Microalgae, Scenedesmus bijuga, was cultivated in anaerobically digested food wastewater effluent (FWE) to treat the wastewater and produce biodiesel simultaneously. Three different mixing ratios with municipal wastewater were compared for finding out proper dilution ratio in biodiesel production. Of these, 1/20 diluted FWE showed the highest biomass production (1.49 g/L). Lipid content was highest in 1/10 diluted FWE (35.06%), and the lipid productivity showed maximum value in 1/20 diluted FWE (15.59 mg/L/d). Nutrient removal was also measured in the cultivation. FAME compositions were mainly composed of C16-C18 (Over 98.94%) in S. bijuga. In addition, quality of FAMEs was evaluated by Cetane Number (CN) and Bis-allylic Position Equivalent (BAPE). Copyright © 2015. Published by Elsevier Ltd.

  4. Oil company profitability: observations on the use of oil product price assessments and associated errors

    International Nuclear Information System (INIS)

    Jenkins, Gilbert

    2000-01-01

    Oil companies often report the exact price obtained for crude oil sales. Furthermore, crude oil prices may be linked to the price of Brent crude oil which is actively and very transparently traded on the International Petroleum Exchange. Brent crude oil prices are reported worldwide electronically and in many newspapers on a daily basis. Gas oil (No. 2 Fuel oil in the USA) is actively traded on the IPE and on NYMEX and the prices are also reported worldwide almost instantaneously. One grade of unleaded gasoline is traded on NYMEX but all other oil products do not have regulated and transparent markets. The prices of these products are assessed by price reporters following daily discussions with active oil traders. Two prices are assessed and reported, the bid (low) and offer (high) even if no trade has taken place. The oil industry itself and oil products consumers make much use of these assessed prices. The object of this paper is to provide some statistical detail on the differences between various product price assessments made through 2000. From these differences, it is possible to provide an indication of the precision of oil product price assessments However, it is doubtful if precision data based on a simple determination of the standard deviation of the differences between the assessment made by the various price reporting services would be of practical use. (Author)

  5. Disposal of by-products in olive oil industry: waste-to-energy solutions

    International Nuclear Information System (INIS)

    Caputo, Antonio C.; Scacchia, Federica; Pelagagge, Pacifico M.

    2003-01-01

    Olive oil production industry is characterized by relevant amounts of liquid and solid by-products [olive mill wastewater (OMW) and olive husk (OH)], and by economical, technical and organizational constraints that make difficult the adoption of environmentally sustainable waste disposal approaches. In this context, waste treatment technologies aimed at energy recovery represent an interesting alternative. In the paper, a technical and economical analysis of thermal disposal plant solutions with energy recovery has been carried out. The considered plants enable the combined treatment of OMW and OH which, although penalizes the energy recovery, proves to be feasible and profitable in a future legislative scenario when stricter limitation on OMW disposal will force oil producers to bear high disposal costs. Results are compared by using economic performance measures, including revenues from produced energy and avoided disposal costs. A sensitivity and risk analysis is also performed in order to assess the economic profitability of the proposed solutions

  6. A Study on the Preparation of Regular Multiple Micro-Electrolysis Filler and the Application in Pretreatment of Oil Refinery Wastewater

    Directory of Open Access Journals (Sweden)

    Ruihong Yang

    2016-04-01

    Full Text Available Through a variety of material screening experiments, Al was selected as the added metal and constituted a multiple micro-electrolysis system of Fe/C/Al. The metal proportion of alloy-structured filler was also analyzed with the best Fe/C/Al ratio of 3:1:1. The regular Fe/C/Al multiple micro-electrolysis fillers were prepared using a high-temperature anaerobic roasting method. The optimum conditions for oil refinery wastewater treated by Fe/C/Al multiple micro-electrolysis were determined to be an initial pH value of 3, reaction time of 80 min, and 0.05 mol/L Na2SO4 additive concentration. The reaction mechanism of the treatment of oil refinery wastewater by Fe/C/Al micro-electrolysis was investigated. The process of the treatment of oil refinery wastewater with multiple micro-electrolysis conforms to the third-order reaction kinetics. The gas chromatography–mass spectrometry (GC–MS used to analyze the organic compounds of the oil refinery wastewater before and after treatment and the Ultraviolet–visible spectroscopy (UV–VIS absorption spectrum analyzed the degradation process of organic compounds in oil refinery wastewater. The treatment effect of Fe/C/Al multiple micro-electrolysis was examined in the continuous experiment under the optimum conditions, which showed high organic compound removal and stable treatment efficiency.

  7. A Study on the Preparation of Regular Multiple Micro-Electrolysis Filler and the Application in Pretreatment of Oil Refinery Wastewater.

    Science.gov (United States)

    Yang, Ruihong; Zhu, Jianzhong; Li, Yingliu; Zhang, Hui

    2016-04-29

    Through a variety of material screening experiments, Al was selected as the added metal and constituted a multiple micro-electrolysis system of Fe/C/Al. The metal proportion of alloy-structured filler was also analyzed with the best Fe/C/Al ratio of 3:1:1. The regular Fe/C/Al multiple micro-electrolysis fillers were prepared using a high-temperature anaerobic roasting method. The optimum conditions for oil refinery wastewater treated by Fe/C/Al multiple micro-electrolysis were determined to be an initial pH value of 3, reaction time of 80 min, and 0.05 mol/L Na₂SO₄ additive concentration. The reaction mechanism of the treatment of oil refinery wastewater by Fe/C/Al micro-electrolysis was investigated. The process of the treatment of oil refinery wastewater with multiple micro-electrolysis conforms to the third-order reaction kinetics. The gas chromatography-mass spectrometry (GC-MS) used to analyze the organic compounds of the oil refinery wastewater before and after treatment and the Ultraviolet-visible spectroscopy (UV-VIS) absorption spectrum analyzed the degradation process of organic compounds in oil refinery wastewater. The treatment effect of Fe/C/Al multiple micro-electrolysis was examined in the continuous experiment under the optimum conditions, which showed high organic compound removal and stable treatment efficiency.

  8. Feed supplemented with byproducts from olive oil mill wastewater processing increases antioxidant capacity in broiler chickens.

    Science.gov (United States)

    Gerasopoulos, Konstantinos; Stagos, Dimitrios; Kokkas, Stylianos; Petrotos, Konstantinos; Kantas, Dimitrios; Goulas, Panagiotis; Kouretas, Dimitrios

    2015-08-01

    In the present study, a ceramic membrane microfiltration method was used for the separation of two liquid products, the downstream permeate and the upstream retentate, from olive mill wastewater (OMWW). These liquid products were examined for their antioxidant activity by incorporating them into broilers' feed. Twenty four broilers 13 d old were divided into two feeding groups receiving supplementation with OMWW retentate or permeate for 37 d. Blood was drawn at 17, 27 and 37 d, while tissues (muscle, heart, liver) were collected at 37 d. The antioxidant effects were assessed by measuring oxidative stress biomarkers in blood and tissues. The results showed that broilers given feed supplemented with OMWW retentate or permeate had significantly lower protein oxidation and lipid peroxidation levels and higher total antioxidant capacity in plasma and tissues compared to control group. In both OMWW groups, catalase activity in erythrocytes and tissues was significantly increased compared to control group. OMWW retentate administration increased significantly GSH in erythrocytes in broilers with low GSH, although both OMWW products significantly reduced GSH in broilers with high GSH. Thus, it has been demonstrated for the first time that supplementation with OMWW processing residues could be used for enhancing broilers' redox status. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Long-Term Effects of Olive oil Mill wastewater spreading on soil and olive trees

    Energy Technology Data Exchange (ETDEWEB)

    Ben rouina, B.; Ben Ahmed, C.; Boukhris, M.

    2009-07-01

    The olive oil extraction process produces huge amounts of liquid waste called olive mill waste water (OMWW). Large amounts of OMWW (30 million m{sup 3}) are produced in the Mediterranean regions that accounts for 95% of the total olive oil production worldwide. In Tunisia, OMWW constitutes a serious environmental problem due to the features associated with this type of agro-waste and to its diverse organic load which may reach values as high as 100 g/L and is mained with this type of agro-waste and to its diverse organic load which may reach values as high as 100 g/L is mainly due to sugars. lipids, phenols, and tannins. (Author)

  10. Long-Term Effects of Olive oil Mill wastewater spreading on soil and olive trees

    International Nuclear Information System (INIS)

    Ben rouina, B.; Ben Ahmed, C.; Boukhris, M.

    2009-01-01

    The olive oil extraction process produces huge amounts of liquid waste called olive mill waste water (OMWW). Large amounts of OMWW (30 million m 3 ) are produced in the Mediterranean regions that accounts for 95% of the total olive oil production worldwide. In Tunisia, OMWW constitutes a serious environmental problem due to the features associated with this type of agro-waste and to its diverse organic load which may reach values as high as 100 g/L and is mained with this type of agro-waste and to its diverse organic load which may reach values as high as 100 g/L is mainly due to sugars. lipids, phenols, and tannins. (Author)

  11. Challenges and Prospects of Smallholder Oil Palm Production in ...

    African Journals Online (AJOL)

    The study examined the challenges and prospects of smallholder oil palm production in Awka Agricultural Zone of Anambra State. Seventy two smallholder oil palm farmers were interviewed for the purpose of eliciting information. Smallholder oil palm farmers in Awka Agricultural Zone were educated (79.2% - Senior ...

  12. Effect Of Weed On Oil Palm Inflorenscence Production: Implication ...

    African Journals Online (AJOL)

    Weed consistently depressed the performance of oil palm and this depressive effect was attributed to aggressive growth resources, smothering of the oil palm and preventing the palm from proper ventilation and solar radiation. Weed interference on inflorescence production of oil palm was assessed with the view of ...

  13. Enzymatic biodiesel production from sludge palm oil (SPO) using ...

    African Journals Online (AJOL)

    Biodiesel is a non-toxic, renewable and environmental friendly fuel. This study involved the production of biodiesel from sludge palm oil (SPO), a low-cost waste oil via enzymatic catalysis. The enzyme catalyst was a Candida cylindracea lipase, locally-produced using palm oil mill effluent as the low cost based medium.

  14. Refining of the cracked products of mineral oils, etc

    Energy Technology Data Exchange (ETDEWEB)

    Seelig, S

    1928-06-02

    A process is disclosed for the refining of the distilled or cracked products from mineral oil, shale oil, or brown-coal-tar oil, with the aid of alkali-plumbite solution, characterized by adding to the plumbite solution from oxide, iron hydroxide, basic oxide, or an iron salt.

  15. Utilization of some non-edible oil for biodiesel production ...

    African Journals Online (AJOL)

    In this work, the production of biodiesel from four sources of non-edible oils, namely jatropha, animal fat, waste vegetable oil and castor oil was carried out. It was done using an acid esterification process followed by alkali transesterification in the laboratory. Subsequently the physicochemical properties for four blends B100 ...

  16. Market analysis of shale oil co-products. Appendices

    Energy Technology Data Exchange (ETDEWEB)

    1980-12-01

    Data are presented in these appendices on the marketing and economic potential for soda ash, aluminia, and nahcolite as by-products of shale oil production. Appendices 1 and 2 contain data on the estimated capital and operating cost of an oil shales/mineral co-products recovery facility. Appendix 3 contains the marketing research data.

  17. Co-cultivation of fungal and microalgal cells as an efficient system for harvesting microalgal cells, lipid production and wastewater treatment.

    Directory of Open Access Journals (Sweden)

    Digby Wrede

    Full Text Available The challenges which the large scale microalgal industry is facing are associated with the high cost of key operations such as harvesting, nutrient supply and oil extraction. The high-energy input for harvesting makes current commercial microalgal biodiesel production economically unfeasible and can account for up to 50% of the total cost of biofuel production. Co-cultivation of fungal and microalgal cells is getting increasing attention because of high efficiency of bio-flocculation of microalgal cells with no requirement for added chemicals and low energy inputs. Moreover, some fungal and microalgal strains are well known for their exceptional ability to purify wastewater, generating biomass that represents a renewable and sustainable feedstock for biofuel production. We have screened the flocculation efficiency of the filamentous fungus A. fumigatus against 11 microalgae representing freshwater, marine, small (5 µm, large (over 300 µm, heterotrophic, photoautotrophic, motile and non-motile strains. Some of the strains are commercially used for biofuel production. Lipid production and composition were analysed in fungal-algal pellets grown on media containing alternative carbon, nitrogen and phosphorus sources contained in wheat straw and swine wastewater, respectively. Co-cultivation of algae and A. fumigatus cells showed additive and synergistic effects on biomass production, lipid yield and wastewater bioremediation efficiency. Analysis of fungal-algal pellet's fatty acids composition suggested that it can be tailored and optimised through co-cultivating different algae and fungi without the need for genetic modification.

  18. Co-cultivation of fungal and microalgal cells as an efficient system for harvesting microalgal cells, lipid production and wastewater treatment.

    Science.gov (United States)

    Wrede, Digby; Taha, Mohamed; Miranda, Ana F; Kadali, Krishna; Stevenson, Trevor; Ball, Andrew S; Mouradov, Aidyn

    2014-01-01

    The challenges which the large scale microalgal industry is facing are associated with the high cost of key operations such as harvesting, nutrient supply and oil extraction. The high-energy input for harvesting makes current commercial microalgal biodiesel production economically unfeasible and can account for up to 50% of the total cost of biofuel production. Co-cultivation of fungal and microalgal cells is getting increasing attention because of high efficiency of bio-flocculation of microalgal cells with no requirement for added chemicals and low energy inputs. Moreover, some fungal and microalgal strains are well known for their exceptional ability to purify wastewater, generating biomass that represents a renewable and sustainable feedstock for biofuel production. We have screened the flocculation efficiency of the filamentous fungus A. fumigatus against 11 microalgae representing freshwater, marine, small (5 µm), large (over 300 µm), heterotrophic, photoautotrophic, motile and non-motile strains. Some of the strains are commercially used for biofuel production. Lipid production and composition were analysed in fungal-algal pellets grown on media containing alternative carbon, nitrogen and phosphorus sources contained in wheat straw and swine wastewater, respectively. Co-cultivation of algae and A. fumigatus cells showed additive and synergistic effects on biomass production, lipid yield and wastewater bioremediation efficiency. Analysis of fungal-algal pellet's fatty acids composition suggested that it can be tailored and optimised through co-cultivating different algae and fungi without the need for genetic modification.

  19. Production of organic fertilizer from olive mill wastewater by combining solar greenhouse drying and composting.

    Science.gov (United States)

    Galliou, F; Markakis, N; Fountoulakis, M S; Nikolaidis, N; Manios, T

    2018-05-01

    Olive mill wastewater (OMW) is generated during the production of olive oil. Its disposal is still a major environmental problem in Mediterranean countries, despite the fact that a large number of technologies have been proposed up to date. The present work examines for the first time a novel, simple and low-cost technology for OMW treatment combining solar drying and composting. In the first step, OMW was dried in a chamber inside a solar greenhouse using swine manure as a bulking agent. The mean evaporation rate was found to be 5.2 kg H 2 O/m 2 /d for a drying period of 6 months (February-August). High phenol (75%) and low nitrogen (15%) and carbon (15%) losses were recorded at the end of the solar drying process. The final product after solar drying was rich in nutrients (N: 27.8 g/kg, P: 7.3 g/kg, K: 81.6 g/kg) but still contained significant quantities of phenols (18.4 g/kg). In order to detoxify the final product, a composting process was applied as a second step with or without the use of grape marc as bulking agent. Results showed that the use of grape marc as a bulking agent at a volume ratio of 1:1 achieved a higher compost temperature profile (60 °C) than 2:1 (solar drying product: grape marc) or no use (solar drying product). The end product after the combination of solar drying and composting had the characteristics of an organic fertilizer (57% organic carbon) rich in nutrients (3.5% N, 1% P, 6.5% K) with quite low phenol content (2.9 g/kg). Finally, the use of this product for the cultivation of pepper plants approved its fertility which was found similar with commercial NPK fertilizers. Copyright © 2018 Elsevier Ltd. All rights reserved.

  20. Risk management of Norwegian oil production; Risikostyring av norsk oljeproduksjon

    Energy Technology Data Exchange (ETDEWEB)

    Kloegetvedt, Bjoern

    1998-07-01

    The items discussed in this presentation are: (1) Oil price chronology, (2) Market structure - Forward prices, (3) Volatility in oil prices, (4) Sales strategies and price fixing, (5) Development of ''Risk Management'' in the oil trading, (6) Oil products and markets, (7) Management of risk exposure, (8) Strong points and weak points of the norm price system, (9) Comparison with UK.

  1. State and trends of oil crops production in China

    Directory of Open Access Journals (Sweden)

    Yang Tiankui

    2016-11-01

    Full Text Available This paper attempts to present a full picture of current situation and future trends of Chinese oil crop production. The total oil crop production remained broadly constant during 2011–2014. The top three oil crops are soybean, peanut and rapeseed, together accounting for more than 70% of total oil crop production. The area under cultivation and the production of peanuts will keep steadily increasing because most Chinese like its pleasant roasted flavor. Because of their high content in polyunsaturated fatty acids and the natural minor functional components in their oils, more attention is being paid to sunflower seed and rice bran. The diminishing availability of arable land and concern over the security of edible oil supplies is driving both a change in cultivation structure of crops and improvements in the efficiency of oilseed production in China.

  2. Petrophysical studies in heavy oil sands with early water production - Hamaca area, Orinoco Oil Belt

    Energy Technology Data Exchange (ETDEWEB)

    Salisch, H.A.

    1982-07-01

    This study describes the main lines of petrophysical research in the Hamaca-Pao region of the Orinoco Oil Belt. The techniques and parameters most appropriate for petrophysical studies in the area of interest are discussed. Field tests have confirmed the conclusions of this study on early water production and low oil recovery. Steam injection was shown to be a means for increasing oil mobility to such a degree that significant amounts of additional oil can be produced.

  3. Bio-oil production from dry sewage sludge by fast pyrolysis in an electrically-heated fluidized bed reactor

    Directory of Open Access Journals (Sweden)

    Renato O. Arazo

    2017-01-01

    Full Text Available The optimization of bio-oil produced from sewage sludge using fast pyrolysis in a fluidized bed reactor was investigated. Effects of temperature, sludge particle size and vapor residence time on bio-oil properties, such as yield, high heating value (HHV and moisture content were evaluated through experimental and statistical analyses. Characterization of the pyrolysis products (bio-oil and biogas was also done. Optimum conditions produced a bio-oil product with an HHV that is nearly twice as much as lignocellulosic-derived bio-oil, and with properties comparable to heavy fuel oil. Contrary to generally acidic bio-oil, the sludge-derived bio-oil has almost neutral pH which could minimize the pipeline and engine corrosions. The Fourier Transform Infrared and gas-chromatography and mass spectrometry analyses of bio-oil showed a dominant presence of gasoline-like compounds. These results demonstrate that fast pyrolysis of sewage sludge from domestic wastewater treatment plant is a favorable technology to produce biofuels for various applications.

  4. Production of polyhydroxyalcanoates (PHAs) using milk whey and dairy wastewater activated sludge production of bioplastics using dairy residues.

    Science.gov (United States)

    Bosco, Francesca; Chiampo, Fulvia

    2010-04-01

    The production of polyhydroxyalcanoates (PHAs), which are biodegradable plastics, was studied using milk whey and dairy wastewater activated sludge to define a suitable C/N ratio, the pre-treatments required to reduce the protein content, and the effect of pH correction. The results show good production of PHAs at a C/N=50 and without pH correction. The use of dairy wastewater activated sludge has the advantage of not requiring aseptic conditions. Copyright 2009 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  5. Scale up of ethanol production using pulp mill wastewater sludge by cellulase and saccharomyces cerevisiae

    International Nuclear Information System (INIS)

    Kunchada Sangasintu; Petchporn Chawakitchareon

    2010-01-01

    This study aimed to evaluate the potential use of pulp mill wastewater sludge as substrate in ethanol production. The simultaneous saccharification and fermentation process was conducted by using Saccharomyces cerevisiae TISTR 5339 under optimum proportion of cellulase and pulp mill wastewater sludge. The ethanol production from cellulosic materials in simultaneous saccharification and fermentation needs cooperation between cellulase and yeast. The cellulase hydrolyzes cellulose to sugar while yeast utilizes sugar to produce ethanol. The pulp mill wastewater sludge has an average content of 73.3 % hemi cellulose, 67.1 % alpha cellulose, 4.7 % beta cellulose and 1.4 % gamma cellulose. The experimental results indicated that the volume of the ethanol tend to increase with time, providing the maximum ethanol yield of 0.69 g/g on the 7"t"h day, the last day of the experiment. The ethanol production was scaled up in 5 L fermentor under optimum proportion and increased the fermentation period. It was found that the ethanol production gave the maximum ethanol yield of 1.14 g/g on the 9"t"h day of the totally 13 days experimentation. These results showed that the cellulose from pulp mill wastewater sludge was as effective substrate for ethanol production and alternative energy for the future. (author)

  6. Thin layer drying kinetics of by-products from olive oil processing.

    Science.gov (United States)

    Montero, Irene; Miranda, Teresa; Arranz, Jose Ignacio; Rojas, Carmen Victoria

    2011-01-01

    The thin-layer behavior of by-products from olive oil production was determined in a solar dryer in passive and active operation modes for a temperature range of 20-50 °C. The increase in the air temperature reduced the drying time of olive pomace, sludge and olive mill wastewater. Moisture ratio was analyzed to obtain effective diffusivity values, varying in the oil mill by-products from 9.136 × 10(-11) to 1.406 × 10(-9) m(2)/s in forced convection (m(a) = 0.22 kg/s), and from 9.296 × 10(-11) to 6.277 × 10(-10) m(2)/s in natural convection (m(a) = 0.042 kg/s). Diffusivity values at each temperature were obtained using the Fick's diffusion model and, regardless of the convection, they increased with the air temperature. The temperature dependence on the effective diffusivity was determined by an Arrhenius type relationship. The activation energies were found to be 38.64 kJ/mol, 30.44 kJ/mol and 47.64 kJ/mol for the olive pomace, the sludge and the olive mill wastewater in active mode, respectively, and 91.35 kJ/mol, 14.04 kJ/mol and 77.15 kJ/mol in natural mode, in that order.

  7. Life-Cycle Assessment of Pyrolysis Bio-Oil Production*

    Energy Technology Data Exchange (ETDEWEB)

    Steele, Philip; Puettmann, Maureen E.; Penmetsa, Venkata Kanthi; Cooper, Jerome E.

    2012-07-01

    As part ofthe Consortium for Research on Renewable Industrial Materials' Phase I life-cycle assessments ofbiofuels, lifecycle inventory burdens from the production of bio-oil were developed and compared with measures for residual fuel oil. Bio-oil feedstock was produced using whole southern pine (Pinus taeda) trees, chipped, and converted into bio-oil by fast pyrolysis. Input parameters and mass and energy balances were derived with Aspen. Mass and energy balances were input to SimaPro to determine the environmental performance of bio-oil compared with residual fuel oil as a heating fuel. Equivalent functional units of 1 MJ were used for demonstrating environmental preference in impact categories, such as fossil fuel use and global warming potential. Results showed near carbon neutrality of the bio-oil. Substituting bio-oil for residual fuel oil, based on the relative carbon emissions of the two fuels, estimated a reduction in CO2 emissions by 0.075 kg CO2 per MJ of fuel combustion or a 70 percent reduction in emission over residual fuel oil. The bio-oil production life-cycle stage consumed 92 percent of the total cradle-to-grave energy requirements, while feedstock collection, preparation, and transportation consumed 4 percent each. This model provides a framework to better understand the major factors affecting greenhouse gas emissions related to bio-oil production and conversion to boiler fuel during fast pyrolysis.

  8. Life Cycle Assessment for the Production of Oil Palm Seeds.

    Science.gov (United States)

    Muhamad, Halimah; Ai, Tan Yew; Khairuddin, Nik Sasha Khatrina; Amiruddin, Mohd Din; May, Choo Yuen

    2014-12-01

    The oil palm seed production unit that generates germinated oil palm seeds is the first link in the palm oil supply chain, followed by the nursery to produce seedling, the plantation to produce fresh fruit bunches (FFB), the mill to produce crude palm oil (CPO) and palm kernel, the kernel crushers to produce crude palm kernel oil (CPKO), the refinery to produce refined palm oil (RPO) and finally the palm biodiesel plant to produce palm biodiesel. This assessment aims to investigate the life cycle assessment (LCA) of germinated oil palm seeds and the use of LCA to identify the stage/s in the production of germinated oil palm seeds that could contribute to the environmental load. The method for the life cycle impact assessment (LCIA) is modelled using SimaPro version 7, (System for Integrated environMental Assessment of PROducts), an internationally established tool used by LCA practitioners. This software contains European and US databases on a number of materials in addition to a variety of European- and US-developed impact assessment methodologies. LCA was successfully conducted for five seed production units and it was found that the environmental impact for the production of germinated oil palm was not significant. The characterised results of the LCIA for the production of 1000 germinated oil palm seeds showed that fossil fuel was the major impact category followed by respiratory inorganics and climate change.

  9. Biodiesel production methods of rubber seed oil: a review

    Science.gov (United States)

    Ulfah, M.; Mulyazmi; Burmawi; Praputri, E.; Sundari, E.; Firdaus

    2018-03-01

    The utilization of rubber seed as raw material of biodiesel production is seen highly potential in Indonesia. The availability of rubber seeds in Indonesia is estimated about 5 million tons per annum, which can yield rubber seed oil about 2 million tons per year. Due to the demand of edible oils as a food source is tremendous and the edible oil feedstock costs are far expensive to be used as fuel, production of biodiesel from non-edible oils such as rubber seed is an effective way to overcome all the associated problems with edible oils. Various methods for producing biodiesel from rubber seed oil have been reported. This paper introduces an optimum condition of biodiesel production methods from rubber seed oil. This article was written to be a reference in the selection of methods and the further development of biodiesel production from rubber seed oil. Biodiesel production methods for rubber seed oils has been developed by means of homogeneous catalysts, heterogeneous catalysts, supercritical method, ultrasound, in-situ and enzymatic processes. Production of biodiesel from rubber seed oil using clinker loaded sodium methoxide as catalyst is very interesting to be studied and developed further.

  10. Depuration of olive oil mill wastewater by an activated sludge system; Depuracion de alpechin mediante us sistema de fangos activados

    Energy Technology Data Exchange (ETDEWEB)

    Beltran de Heredia, J.; Torregrosa Anton, J.; Ramos Viscas, M. P.; Garcia Rodriguez, J.; Dominguez Vargas, R. [Universidad de Extremadura. Badajoz (Spain)

    1999-07-01

    In the present work, the degradation of alpechin (olive oil mill wastewaters) have been studied by an activated sludge treatment. The substrate evolution (based on COD and BOD{sub 5}), nitrogen Kjeldahl, phosphorus, biomass, aromaticity and total polyphenolic contents was followed during each experiment. A kinetic study is performed by using the Contois model, which applied to the experimental data, provides the specific kinetic parameters of this model. Moreover, others interesting biological parameters like the cellular yield and the kinetics of endogenous metabolism were determined. (Author) 17 refs.

  11. The use of treated wastewater for chemlali olive tree irrigation: effects on soil properties, growth and oil quality

    Energy Technology Data Exchange (ETDEWEB)

    Ben Rouina, B.; Bedbabis, S.; Ben Ahmed, C.; Boukhris, M.

    2009-07-01

    Olive tree (Olea european L.) cultivation, the major tree crops in Mediterranean countries is being extended to irrigated lands. However, the limited water availability, the severe climatic conditions and the increased need for good water quality for urban and industrial sector uses are leading to the urgent use of less water qualities (brackish water and recycled wastewater) for olive tree irrigation. The aim of this work was to asses the effects of long term irrigation with treated waste water (TWW) on the soil chemical properties, on olive tree growth and on oil quality characteristics. (Author)

  12. The use of treated wastewater for chemlali olive tree irrigation: effects on soil properties, growth and oil quality

    International Nuclear Information System (INIS)

    Ben Rouina, B.; Bedbabis, S.; Ben Ahmed, C.; Boukhris, M.

    2009-01-01

    Olive tree (Olea european L.) cultivation, the major tree crops in Mediterranean countries is being extended to irrigated lands. However, the limited water availability, the severe climatic conditions and the increased need for good water quality for urban and industrial sector uses are leading to the urgent use of less water qualities (brackish water and recycled wastewater) for olive tree irrigation. The aim of this work was to asses the effects of long term irrigation with treated waste water (TWW) on the soil chemical properties, on olive tree growth and on oil quality characteristics. (Author)

  13. Treatability studies on different refinery wastewater samples using high-throughput microbial electrolysis cells (MECs)

    KAUST Repository

    Ren, Lijiao; Siegert, Michael; Ivanov, Ivan; Pisciotta, John M.; Logan, Bruce E.

    2013-01-01

    High-throughput microbial electrolysis cells (MECs) were used to perform treatability studies on many different refinery wastewater samples all having appreciably different characteristics, which resulted in large differences in current generation. A de-oiled refinery wastewater sample from one site (DOW1) produced the best results, with 2.1±0.2A/m2 (maximum current density), 79% chemical oxygen demand removal, and 82% headspace biological oxygen demand removal. These results were similar to those obtained using domestic wastewater. Two other de-oiled refinery wastewater samples also showed good performance, with a de-oiled oily sewer sample producing less current. A stabilization lagoon sample and a stripped sour wastewater sample failed to produce appreciable current. Electricity production, organics removal, and startup time were improved when the anode was first acclimated to domestic wastewater. These results show mini-MECs are an effective method for evaluating treatability of different wastewaters. © 2013 Elsevier Ltd.

  14. Treatability studies on different refinery wastewater samples using high-throughput microbial electrolysis cells (MECs)

    KAUST Repository

    Ren, Lijiao

    2013-05-01

    High-throughput microbial electrolysis cells (MECs) were used to perform treatability studies on many different refinery wastewater samples all having appreciably different characteristics, which resulted in large differences in current generation. A de-oiled refinery wastewater sample from one site (DOW1) produced the best results, with 2.1±0.2A/m2 (maximum current density), 79% chemical oxygen demand removal, and 82% headspace biological oxygen demand removal. These results were similar to those obtained using domestic wastewater. Two other de-oiled refinery wastewater samples also showed good performance, with a de-oiled oily sewer sample producing less current. A stabilization lagoon sample and a stripped sour wastewater sample failed to produce appreciable current. Electricity production, organics removal, and startup time were improved when the anode was first acclimated to domestic wastewater. These results show mini-MECs are an effective method for evaluating treatability of different wastewaters. © 2013 Elsevier Ltd.

  15. Wastewater reuse

    Directory of Open Access Journals (Sweden)

    Milan R. Radosavljević

    2013-12-01

    Full Text Available Water scarcity and water pollution are some of the crucial issues that must be addressed within local and global perspectives. One of the ways to reduce the impact of water scarcity  and to minimizine water pollution is to expand water and wastewater reuse. The local conditions including regulations, institutions, financial mechanisms, availability of local technology and stakeholder participation have a great influence on the decisions for wastewater reuse. The increasing awareness of food safety and the influence of the countries which import food are influencing policy makers and agriculturists to improve the standards of wastewater reuse in agriculture. The environmental awareness of consumers has been putting pressure on the producers (industries to opt for environmentally sound technologies including those which conserve water and reduce the level of pollution. It may be observed that we have to move forwards to implement strategies and plans for wastewater reuse. However, their success and sustainability will depend on political will, public awareness and active support from national and international agencies to create favorable    environment for the promotion of environmentally sustainable technologies. Wastewater treatment has a long history, especially in agriculture, but also in industry and households. Poor quality of wastewater can pose a significant risk to the health of farmers and users of agricultural products. The World Health Organization (WHO is working on a project for the reuse of wastewater in agriculture. To reduce effects of human activities to the minimum, it is necessary to provide such technical and technological solutions that would on the one hand ensure complying with  the existing regulations and legislation, and on the other hand provide economically viable systems as seen through investments and operating costs. The use of wastewater The practice of using wastewater varies from country to country. Its

  16. Synthesis of sulfated Y-doped zirconia particles and effect on properties of polysulfone membranes for treatment of wastewater containing oil

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Yuqing, E-mail: zhangyuqing@tju.edu.cn [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); ARC Centre for Functional Nanomaterials, AIBN and School of Engineering, University of Queensland, Brisbane 4072 (Australia); Shan Xing; Jin Zhenhua; Wang Yueling [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China)

    2011-08-30

    Highlights: {yields} Novel hybrid membrane material - sulfated Y-doped zirconia particle is prepared. {yields} SZY/PSF membrane is formed by doping SZY particles into PSF membrane. {yields} Hydrophilicity, antifouling and anti-compaction property of PSF membrane is improved. {yields} Treatment efficiency of wastewater containing oil is enhanced. - Abstract: Polysulfone (PSF) membranes are broadly applied in many fields owing to good physicochemical stability, resistance to oxidation and chlorine. But when treated with wastewater containing oil, PSF membranes are easily contaminated due to their hydrophilicity, causing declining flux and lifespan of the membranes thereby limiting their large scale applications. In order to enhance the hydrophilic and anti-fouling capability of PSF membranes for treating wastewater containing oil, sulfated Y-doped zirconia particles (SO{sub 4}{sup 2-}/ZrO{sub 2}-Y{sub 2}O{sub 3} or SZY particles) were firstly synthesized and then doped into polysulfone to fabricate a novel hybrid membrane (SZY/PSF). The optimum preparation conditions of SZY particles were studied and determined. SZY particles were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR), specific surface area and transmission electron microscopy (TEM). Wastewater containing oil (80 mg/L) was used to investigate the separation properties of SZY/PSF membranes. The results show that the oil concentration in the permeation is 0.67 mg/L, which meets the recycle standard of the Chinese oil-field (SY/T 5329-94, oil concentration <10 mg/L). It is concluded that doping SZY particles into polysulfone can reasonably resist membrane fouling and SZY/PSF membranes can be considered feasible in treating wastewater containing oil.

  17. Isolation of Bacillus sp Producing Polyhydroxyalkanoate (PHA from Isfahan Refinery Wastewater and Qualification of Production in Submerged Fermentation

    Directory of Open Access Journals (Sweden)

    Mahsa Keshavarz Azam

    2015-12-01

    Full Text Available Introduction: The aim of present study was isolation of polyhydroxybutyrate producing Bacillus species from oil refinery waste water, Isfahan, Iran and primarily optimization of production condition. Petroleum wastes are rich of carbon sources and have low amounts of nitrogen and phosphorus sources. AS the most important factor in production of intracellular inclusions is increasing the C/N ratio, it seemed that polyhydroxybutyrate producing microorganisms will be found in these wastes. Materials and methods: Bacillus species were isolated and purified from oil refinery wastewater. The polymer was verified using different staining procedures. Polymer was extracted by digestion method and the optimum production conditions were investigated in minimal salt medium with the organic carbon source by submerged fermentation. Production of polyhydroxybutyrate was studied using dry weight and optical density measurement. Results: Between various isolated Bacillus strains, two of them (B1 and B2 were polyhydroxybutyrate producers. Maximum PHA production based on dry weight and concentration were obtained for strain B1 after 72 hours incubation, at 31°C, in the presence of glucose as carbon source and yeast extract as nitrogen source, pH=7, and aeration in 120 rpm; and for strain B2 in the same condition, except optimal temperature which was 32°C. The most production amounts were 367 mg.ml-1 for B1 and 473 mg.ml-1 for B2 isolates. Also the most polymer percentage was 52/16 and 58.43 for B1 and B2 isolates respectively. Discussion and conclusion: The results showed that the production of polyhydroxybutyrate was increased by optimization of the conditions in both isolates. Using petroleum wastes as well as production of biodegradable plastics, leads to decontamination of theses wastes.

  18. Thermo-Oxidization of Municipal Wastewater Treatment Plant Sludge for Production of Class A Biosolids

    Science.gov (United States)

    Bench-scale reactors were used to test a novel thermo-oxidation process on municipal wastewater treatment plant (WWTP) waste activated sludge (WAS) using hydrogen peroxide (H2O2) to achieve a Class A sludge product appropriate for land application. Reactor ...

  19. Biosurfactant production by Mucor circinelloides on waste frying oil and possible uses in crude oil remediation.

    Science.gov (United States)

    Hasanizadeh, Parvin; Moghimi, Hamid; Hamedi, Javad

    2017-10-01

    Biosurfactants are biocompatible surface active agents which many microorganisms produce. This study investigated the production of biosurfactants by Mucor circinelloides. The effects of different factors on biosurfactant production, including carbon sources and concentrations, nitrogen sources, and iron (II) concentration, were studied and the optimum condition determined. Finally, the strain's ability to remove the crude oil and its relationship with biosurfactant production was evaluated. The results showed that M. circinelloides could reduce the surface tension of the culture medium to 26.6 mN/m and create a clear zone of 12.9 cm diameter in an oil-spreading test. The maximum surface tension reduction was recorded 3 days after incubation. The optimum condition for biosurfactant production was achieved in the presence of 8% waste frying oil as a carbon source, 2 g/L yeast extract as a nitrogen source, and 0.01 mM FeSO 4 . M. circinelloides could consume 8% waste frying oil in 5 days of incubation, and 87.6% crude oil in 12 days of incubation. A direct correlation was observed between oil degradation and surface tension reduction in the first 3 days of fungal growth. The results showed that the waste frying oil could be recommended as an inexpensive oily waste substance for biosurfactant production, and M. circinelloides could have the potential to treat waste frying oil. According to the results, the produced crude biosurfactant or fungal strain could be directly used for the mycoremediation of crude oil contamination in oil fields.

  20. HEAVY-OIL PRODUCTION USING EMULSION FLOODING

    African Journals Online (AJOL)

    user

    ... American Petroleum Institute, EOR = Enhanced Oil Recovery, GOR = Gas Oil Ratio ... concentration, 166.003 is the constant (molar mass of ... (molar mass of CaCO3),1M is the constant value. ... volume of prepared oil-in-water emulsion, that.

  1. An oil production forecast for China considering economic limits

    International Nuclear Information System (INIS)

    Wang, Ke; Feng, Lianyong; Wang, Jianliang; Xiong, Yi; Tverberg, Gail E.

    2016-01-01

    In recent years, it has become apparent that oil prices may not rise endlessly. Unconventional oil is likely to be especially affected by low prices because it tends to be high-priced to extract. To estimate the impact prices might have on future Chinese oil production, we develop a model in which only future unconventional oil production is affected by price. We analyze three price scenarios: Stays Low, Best Estimate, and Ever-Rising Prices. In these scenarios, remaining Ultimate Recoverable Resources (URR) are estimated to be 10%, 50%, and 90% of remaining Technically Recoverable Resources, respectively. Since oil price can be expected to affect the shape of the extraction curve, we spread estimated URR to year using models that do not assume that future production will ultimately produce a symmetric Hubbert-type curve (Multi-Cycle Generalized Weng Model and Stochastic Resource-Constrained Growth Model). In the Best Estimate Scenario, China's oil production is expected to reach a maximum of 226.79 million tons in 2020. In the Ever-Rising Prices Scenario, China's maximum oil production occurs in 2023. In the Stays Low Scenario, maximum production has already been reached. - Highlights: • China's conventional oil reached a peak in 2010 and has begun to decline. • Unconventional oil production will be especially adversely affected by low prices. • Rising selling price of oil may lead to recession, bringing prices back down. • China's total oil supply appears likely to peak about 2020. • Likely oil production is less than Technically Recoverable Resources.

  2. Oil extraction from plant seeds for biodiesel production

    Directory of Open Access Journals (Sweden)

    Yadessa Gonfa Keneni

    2017-04-01

    Full Text Available Energy is basic for development and its demand increases due to rapid population growth, urbanization and improved living standards. Fossil fuels will continue to dominate other sources of energy although it is non-renewable and harm global climate. Problems associated with fossil fuels have driven the search for alternative energy sources of which biodiesel is one option. Biodiesel is renewable, non-toxic, environmental-friendly and an economically feasible options to tackle the depleting fossil fuels and its negative environmental impact. It can be produced from vegetable oils, animal fats, waste oils and algae. However, nowadays, the major feedstocks of biodiesel are edible oils and this has created food vs fuel debate. Therefore, the future prospect is to use non-edible oils, animal fats, waste oils and algae as feedstock for biodiesel. Selection of non-expensive feedstock and the extraction and preparation of oil for biodiesel production is a crucial step due to its relevance on the overall technology. There are three main conventional oil extraction methods: mechanical, chemical/solvent and enzymatic extraction methods. There are also some newly developed oil extraction methods that can be used separately or in combination with the conventional ones, to overcome some disadvantages of the conventional oil extraction methods. This review paper presents, compare and discusses different potential biofuel feedstocks, various oil extraction methods, advantages and disadvantages of different oil extraction methods, and propose future prospective for the improvement of oil extraction methods and sustainability of biodiesel production and utilization.

  3. Production of Detergent from Castor Oil

    OpenAIRE

    Abubakar Garba ISAH

    2006-01-01

    This research work was carried out with the objective of extraction of oil from castor seeds and its utilization to produce a synthetic detergent. Solvent extraction method was employed in extracting the oil and the total percent oil yield was found to be 23.8%. The experimentally determined saponification value of the oil was 183.7275mgKOH/g of oil. The detergent efficiency, determined as a measure of the foamability of the detergent was found to be 2.6cm. The pH tests revealed mildly basic ...

  4. Palm oil mill effluent and municipal wastewater co-treatment by zeolite augmented sequencing batch reactors: Turbidity removal

    Science.gov (United States)

    Farraji, Hossein; Zaman, Nastaein Qamaruz; Aziz, Hamidi Abdul; Sa'at, Siti Kamariah Md

    2017-10-01

    Palm oil mill effluent (POME) is the largest wastewater in Malaysia. Of the 60 million tons of POME produced annually, 2.4-3 million tons are total solids. Turbidity is caused by suspended solids, and 75% of total suspended solids are organic matter. Coagulation and flocculation are popular treatments for turbidity removal. Traditional commercial treatments do not meet discharge standards. This study evaluated natural zeolite and municipal wastewater (MWW)-augmented sequencing batch reactor as a microbiological digestion method for the decontamination of POME in response surface methodology. Aeration, contact time, and MWW/POME ratio were selected as response factors for turbidity removal. Results indicated that turbidity removal varied from 96.7% (MWW/POME ratio=50 %, aeration flow=0.5 L/min, and contact time=12) to 99.31% (MWW/POME ratio=80%, aeration flow 4L/min, and contact time 12 h). This study is the first to present MWW augmentation as a suitable microorganism supplier for turbidity biodegradation in high-strength agroindustrial wastewater.

  5. An energy evaluation of coupling nutrient removal from wastewater with algal biomass production

    International Nuclear Information System (INIS)

    Sturm, Belinda S.M.; Lamer, Stacey L.

    2011-01-01

    Recently, several life cycle analyses of algal biodiesel from virtual production facilities have outlined the potential environmental benefits and energetic balance of the process. There are a wide range of assumptions that have been utilized for these calculations, including the addition of fertilizers and carbon dioxide to achieve high algal yields in open ponds. This paper presents an energy balance of microalgal production in open ponds coupled with nutrient removal from wastewater. Actual microalgal yields and nutrient removal rates were obtained from four pilot-scale reactors (2500 gallons each) fed with wastewater effluent from a conventional activated sludge process for 6 months, and the data was used to estimate an energy balance for treating the total average 12 million gallons per day processed by the wastewater treatment plant. Since one of the most energy-intensive steps is the dewatering of algal cultures, several thickening and dewatering processes were compared. This analysis also includes the energy offset from removing nutrients with algal reactors rather than the biological nutrient removal processes typically utilized in municipal wastewater treatment. The results show that biofuel production is energetically favorable for open pond reactors utilizing wastewater as a nutrient source, even without an energy credit for nutrient removal. The energy content of algal biomass was also considered as an alternate to lipid extraction and biodiesel production. Direct combustion of algal biomass may be a more viable energy source than biofuel production, especially when the lipid content of dry biomass (10% in this field experiment) is lower than the high values reported in lab-scale reactors (50-60%).

  6. English-Igbo glossary creation of palm oil production and ...

    African Journals Online (AJOL)

    The Igbo speaking people are well known for palm oil production and processing in Nigeria. This occupation is one of the lucrative ventures among other trades or occupations for which the Igbo are known. With recent technological advancement in the method of production and processing palm oil, more English terms that ...

  7. Impact of heavy metals on the oil products biodegradation process.

    Science.gov (United States)

    Zukauskaite, Audrone; Jakubauskaite, Viktorija; Belous, Olga; Ambrazaitiene, Dalia; Stasiskiene, Zaneta

    2008-12-01

    Oil products continue to be used as a principal source of energy. Wide-scale production, transport, global use and disposal of petroleum have made them major contaminants in prevalence and quantity in the environment. In accidental spills, actions are taken to remove or remediate or recover the contaminants immediately, especially if they occur in environmentally sensitive areas, for example, in coastal zones. Traditional methods to cope with oil spills are confined to physical containment. Biological methods can have an advantage over the physical-chemical treatment regimes in removing spills in situ as they offer biodegradation of oil fractions by the micro-organisms. Recently, biological methods have been known to play a significant role in bioremediation of oil-polluted coastal areas. Such systems are likely to be of significance in the effective management of sensitive coastal ecosystems chronically subjected to oil spillage. For this reason the aim of this paper is to present an impact of Mn, Cu, Co and Mo quantities on oil biodegradation effectiveness in coastal soil and to determine the relationship between metal concentrations and degradation of two oil products (black oil and diesel fuel). Soil was collected in the Baltic Sea coastal zone oil products degradation area (Klaipeda, Lithuania). The experiment consisted of two parts: study on the influence of micro-elements on the oil product biodegradation process; and analysis of the influence of metal concentration on the number of HDMs. The analysis performed and results obtained address the following areas: impact of metal on a population of hydrocarbon degrading micro-organisms, impact of metals on residual concentrations of oil products, influence of metals on the growth of micro-organisms, inter-relation of metal concentrations with degradation rates. Statistical analysis was made using ;Statgraphics plus' software. The influence of metals on the growth of micro-organisms, the biodegradation process

  8. Microalgal biomass and lipid production in mixed municipal, dairy, pulp and paper wastewater together with added flue gases.

    Science.gov (United States)

    Gentili, Francesco G

    2014-10-01

    The aim of the study was to grow microalgae on mixed municipal and industrial wastewater to simultaneously treat the wastewater and produce biomass and lipids. All algal strains grew in all wastewater mixtures; however, Selenastrum minutum had the highest biomass and lipids yields, up to 37% of the dry matter. Nitrogen and phosphorus removal were high and followed a similar trend in all three strains. Ammonium was reduced from 96% to 99%; this reduction was due to algal growth and not to stripping to the atmosphere, as confirmed by the amount of nitrogen in the dry algal biomass. Phosphate was reduced from 91% to 99%. In all strains used the lipid content was negatively correlated to the nitrogen concentration in the algal biomass. Mixtures of pulp and paper wastewater with municipal and dairy wastewater have great potential to grow algae for biomass and lipid production together with effective wastewater treatment. Copyright © 2014 Elsevier Ltd. All rights reserved.

  9. The evaporation of crude oil and petroleum products

    International Nuclear Information System (INIS)

    Fingas, M. F.

    1996-01-01

    The physics of oil and petroleum evaporation was studied by means of an experimental apparatus. The evaporation was determined by weight loss and recorded on a computer. Examination of the data showed that most oil and petroleum products (those with seven to ten components) evaporate at a logarithmic rate with respect to time, while other petroleum products (those with fewer chemical components) evaporate at a rate which is square root with respect to time. Evaporation of oil and petroleum was not strictly boundary-layer regulated because the typical oil evaporation rate rates do not exceed that of molecular diffusion and thus turbulent diffusion does not increase the evaporation rates. Overall, boundary layer regulation can be ignored in the prediction of oil and petroleum evaporation. The simple equation relating only the logarithm of time (or the square root of time in the case of narrow-cut products) and temperature are sufficient to accurately describe oil evaporation. refs., figs

  10. An integrated prediction and optimization model of biogas production system at a wastewater treatment facility.

    Science.gov (United States)

    Akbaş, Halil; Bilgen, Bilge; Turhan, Aykut Melih

    2015-11-01

    This study proposes an integrated prediction and optimization model by using multi-layer perceptron neural network and particle swarm optimization techniques. Three different objective functions are formulated. The first one is the maximization of methane percentage with single output. The second one is the maximization of biogas production with single output. The last one is the maximization of biogas quality and biogas production with two outputs. Methane percentage, carbon dioxide percentage, and other contents' percentage are used as the biogas quality criteria. Based on the formulated models and data from a wastewater treatment facility, optimal values of input variables and their corresponding maximum output values are found out for each model. It is expected that the application of the integrated prediction and optimization models increases the biogas production and biogas quality, and contributes to the quantity of electricity production at the wastewater treatment facility. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Modeling Peak Oil and the Geological Constraints on Oil Production

    NARCIS (Netherlands)

    Okullo, S.J.; Reynes, F.; Hofkes, M.W.

    2014-01-01

    We propose a model to reconcile the theory of inter-temporal non-renewable resource depletion with well-known stylized facts concerning the exploitation of exhaustible resources such as oil. Our approach introduces geological constraints into a Hotelling type extraction-exploration model. We show

  12. Modeling peak oil and the geological constraints on oil production

    NARCIS (Netherlands)

    Okullo, S.J.; Reynès, F.; Hofkes, M.W.

    2015-01-01

    We propose a model to reconcile the theory of inter-temporal non-renewable resource depletion with well-known stylized facts concerning the exploitation of exhaustible resources such as oil. Our approach introduces geological constraints into a Hotelling type extraction-exploration model. We show

  13. Effectiveness of sal deoiled seed cake as an inducer for protease production from Aeromonas sp. S1 for its application in kitchen wastewater treatment.

    Science.gov (United States)

    Saini, Vandana; Bhattacharya, Amrik; Gupta, Anshu

    2013-08-01

    The present study is an attempt to demonstrate the feasibility of sal (Shorea robusta) deoiled cake--a forest-based industrial by-product--as a cheaper media supplement for augmented protease production from Aeromonas sp. S1 and application of protease in the treatment of kitchen wastewater. Under optimized conditions, protease production could successfully be enhanced to 5.13-fold (527.5 U mL(-1)) on using sal deoiled seed cake extract (SDOCE), as medium additive, compared to an initial production of 102.7 U mL(-1) in its absence. The culture parameters for optimum production of protease were determined to be incubation time (48 h), pH (7.0), SDOCE concentration (3 % (v/v)), inoculum size (0.3-0.6 % (v/v)), and agitation rate (100 rpm). The enzyme was found to have an optimum pH and temperature of 8.0 and 60 °C, respectively. The protease preparation was tested for treatment of organic-laden kitchen wastewater. After 96 h of wastewater treatment under static condition, enzyme preparation was able to reduce 74 % biological oxygen demand, 37 % total suspended solids, and 41 % oil and grease. The higher and improved level of protease obtained using sal deoiled seed cake-based media hence offers a new approach for value addition to this underutilized biomass through industrial enzyme production. The protease produced using this biomass could also be used as pretreatment tool for remediation of organic-rich food wastewater.

  14. Integration of biofiltration and advanced oxidation processes for tertiary treatment of an oil refinery wastewater aiming at water reuse.

    Science.gov (United States)

    Nogueira, A A; Bassin, J P; Cerqueira, A C; Dezotti, M

    2016-05-01

    The combination of biological and chemical oxidation processes is an interesting approach to remove ready, poor, and non-biodegradable compounds from complex industrial wastewaters. In this study, biofiltration followed by H2O2/UV oxidation (or microfiltration) and final reverse osmosis (RO) step was employed for tertiary treatment of an oil refinery wastewater. Biofiltration alone allowed obtaining total organic carbon (TOC), chemical oxygen demand (COD), UV absorbance at 254 nm (UV254), ammonium, and turbidity removal of around 46, 46, 23, 50, and 61 %, respectively. After the combined biological-chemical oxidation treatment, TOC and UV254 removal amounted to 88 and 79 %, respectively. Whereas, the treatment performance achieved with different UV lamp powers (55 and 95 W) and therefore distinct irradiance levels (26.8 and 46.3 mW/cm(2), respectively) were very similar and TOC and UV254 removal rates were highly affected by the applied C/H2O2 ratio. Silt density index (SDI) was effectively reduced by H2O2/UV oxidation, favoring further RO application. C/H2O2 ratio of 1:4, 55 W UV lamp, and 20-min oxidation reaction corresponded to the experimental condition which provided the best cost/benefit ratio for TOC, UV254, and SDI reduction from the biofilter effluent. The array of treatment processes proposed in this study has shown to be adequate for tertiary treatment of the oil refinery wastewater, ensuring the mitigation of membrane fouling problems and producing a final effluent which is suitable for reuse applications.

  15. Endocrine disrupting activities of surface water associated with a West Virginia oil and gas industry wastewater disposal site.

    Science.gov (United States)

    Kassotis, Christopher D; Iwanowicz, Luke R; Akob, Denise M; Cozzarelli, Isabelle M; Mumford, Adam C; Orem, William H; Nagel, Susan C

    2016-07-01

    Currently, >95% of end disposal of hydraulic fracturing wastewater from unconventional oil and gas operations in the US occurs via injection wells. Key data gaps exist in understanding the potential impact of underground injection on surface water quality and environmental health. The goal of this study was to assess endocrine disrupting activity in surface water at a West Virginia injection well disposal site. Water samples were collected from a background site in the area and upstream, on, and downstream of the disposal facility. Samples were solid-phase extracted, and extracts assessed for agonist and antagonist hormonal activities for five hormone receptors in mammalian and yeast reporter gene assays. Compared to reference water extracts upstream and distal to the disposal well, samples collected adjacent and downstream exhibited considerably higher antagonist activity for the estrogen, androgen, progesterone, glucocorticoid and thyroid hormone receptors. In contrast, low levels of agonist activity were measured in upstream/distal sites, and were inhibited or absent at downstream sites with significant antagonism. Concurrent analyses by partner laboratories (published separately) describe the analytical and geochemical profiling of the water; elevated conductivity as well as high sodium, chloride, strontium, and barium concentrations indicate impacts due to handling of unconventional oil and gas wastewater. Notably, antagonist activities in downstream samples were at equivalent authentic standard concentrations known to disrupt reproduction and/or development in aquatic animals. Given the widespread use of injection wells for end-disposal of hydraulic fracturing wastewater, these data raise concerns for human and animal health nearby. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. Characterization of the resistome in manure, soil and wastewater from dairy and beef production systems

    OpenAIRE

    Noelle R. Noyes; Xiang Yang; Lyndsey M. Linke; Roberta J. Magnuson; Shaun R. Cook; Rahat Zaheer; Hua Yang; Dale R. Woerner; Ifigenia Geornaras; Jessica A. McArt; Sheryl P. Gow; Jaime Ruiz; Kenneth L. Jones; Christina A. Boucher; Tim A. McAllister

    2016-01-01

    It has been proposed that livestock production effluents such as wastewater, airborne dust and manure increase the density of antimicrobial resistant bacteria and genes in the environment. The public health risk posed by this proposed outcome has been difficult to quantify using traditional microbiological approaches. We utilized shotgun metagenomics to provide a first description of the resistome of North American dairy and beef production effluents, and identify factors that significantly i...

  17. Produced water management - clean and safe oil and gas production

    International Nuclear Information System (INIS)

    2006-01-01

    The conference contains 22 presentations on topics within pollution sources and abatement, discharge reductions, water analysis and monitoring, water production, treatment and injection, enhanced recovery, condensate water, produced water markets, separation technologies for oil/gas/condensate and water, oil removal from solids, environmental risks of oil and gas production and environmental impacts on ecosystems and fisheries. Some oil field case histories are presented. The main focus is on the northern areas such as the North Sea, the north Atlantic Ocean and the Barents Sea, and technological aspects (tk)

  18. Produced water management - clean and safe oil and gas production

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    The conference contains 22 presentations on topics within pollution sources and abatement, discharge reductions, water analysis and monitoring, water production, treatment and injection, enhanced recovery, condensate water, produced water markets, separation technologies for oil/gas/condensate and water, oil removal from solids, environmental risks of oil and gas production and environmental impacts on ecosystems and fisheries. Some oil field case histories are presented. The main focus is on the northern areas such as the North Sea, the north Atlantic Ocean and the Barents Sea, and technological aspects (tk)

  19. Oil price shocks and policy implications the emergence of U.S. tight oil production: a case study

    OpenAIRE

    Voth, Jeffrey Michael

    2015-01-01

    How have shocks to supply and demand affected global oil prices; and what are key policy implications following the resurgence of oil production in the United States? Highlights: − The recent collapse in global oil prices was dominated by oversupply. − The future of tight oil in the United States is vulnerable to obstacles beyond oil prices. − Opinions on tight oil from the Top 25 think tank organizations are considered. Global oil prices have fallen more than fifty percent since ...

  20. Production of biosurfactants from Pseudomonas aeruginosa PA 1 isolated in oil environments

    Directory of Open Access Journals (Sweden)

    L.M. Santa Anna

    2002-04-01

    Full Text Available The potential production of rhamnolipid-type biosurfactants is assessed based on the development of a fermentative process with a strain of Pseudomonas aeruginosa PA1, which was isolated from oil production wastewater in the Northeast of Brazil. These production of molecules using different carbon (n-hexadecane, paraffinic oil, glycerol and babassu oil and nitrogen sources (NaNO3, (NH42SO4 and CH4N2O was studied. The best results were obtained when using glycerol as substrate. A C/N ratio of 60/1 and use of sodium nitrate as nitrogen source resulted in higher production of the rhamnolipid, expressed by rhamnose (3.16 g/L and by the yield in relation to biomass (Yp/x = 0.70 g/g. Additionally, physical-chemical characteristics of the spent broth with and without cells were studied, providing a low critical micelle concentration of 19 mg/L and toxicity values of 13 and 13.8 mg/L using two test organisms, the micro crustacean Daphnia similis and the bacterium Vibrio fisheri (Microtox, respectively.

  1. Cultivation of Chlorella protothecoides with urban wastewater in continuous photobioreactor: biomass productivity and nutrient removal.

    Science.gov (United States)

    Ramos Tercero, E A; Sforza, E; Morandini, M; Bertucco, A

    2014-02-01

    The capability to grow microalgae in nonsterilized wastewater is essential for an application of this technology in an actual industrial process. Batch experiments were carried out with the species in nonsterilized urban wastewater from local treatment plants to measure both the algal growth and the nutrient consumption. Chlorella protothecoides showed a high specific growth rate (about 1 day(-1)), and no effects of bacterial contamination were observed. Then, this microalgae was grown in a continuous photobioreactor with CO₂-air aeration in order to verify the feasibility of an integrated process of the removal of nutrient from real wastewaters. Different residence times were tested, and biomass productivity and nutrients removal were measured. A maximum of microalgae productivity was found at around 0.8 day of residence time in agreement with theoretical expectation in the case of light-limited cultures. In addition, N-NH₄ and P-PO₄ removal rates were determined in order to model the kinetic of nutrients uptake. Results from batch and continuous experiments were used to propose an integrated process scheme of wastewater treatment at industrial scale including a section with C. protothecoides.

  2. Characterization of persistent colors and decolorization of effluent from biologically treated cellulosic ethanol production wastewater.

    Science.gov (United States)

    Shan, Lili; Liu, Junfeng; Yu, Yanling; Ambuchi, John J; Feng, Yujie

    2016-05-01

    The high chroma of cellulosic ethanol production wastewater poses a serious environmental concern; however, color-causing compounds are still not fully clear. The characteristics of the color compounds and decolorization of biologically treated effluent by electro-catalytic oxidation were investigated in this study. Excitation-emission matrix (EEM), fourier transform infrared spectrometer (FTIR), UV-Vis spectra, and ultrafiltration (UF) fractionation were used to analyze color compounds. High chroma of wastewater largely comes from humic materials, which exhibited great fluorescence proportion (67.1 %) in the biologically treated effluent. Additionally, the color compounds were mainly distributed in the molecular weight fractions with 3-10 and 10-30 kDa, which contributed 53.5 and 34.6 % of the wastewater color, respectively. Further decolorization of biologically treated effluent by electro-catalytic oxidation was investigated, and 98.3 % of color removal accompanied with 97.3 % reduction of humic acid-like matter was achieved after 180 min. The results presented herein will facilitate the development of a well decolorization for cellulosic ethanol production wastewater and better understanding of the biological fermentation.

  3. Study on fermentation kinetics and extraction process of rhamnolipid production by papermaking wastewater

    Science.gov (United States)

    Yu, Keer

    2018-01-01

    Paper mill wastewater (PMW) is the outlet water generated during pulp and papermaking process in the paper industry. Fermentation by wastewater can lower the cost of production as well as alleviate the pressure of wastewater treatment. Rhamnolipids find broad placations as natural surfactants. This paper studied the rhamnolipids fermentation by employing Pseudomonas aeruginosa isolated by the laboratory, and determined to use wastewater which filtered by medium speed filter paper and strain Z2, the culture conditions were optimized, based on the flask shaking fermentation. On the basis of 5L tank fermentation, batch fermentation was carried out, the yield of fermentation reached 7.067g/L and the fermentation kinetics model of cell growth, product formation and substrate consumption was established by using origin software, and the fermentation process could be simulated well. And studied on the extraction process of rhamnolipids, through fermentation dynamic equation analysis can predict the in fill material yield can be further improved. Research on the extraction process of rhamnolipid simplifies the operation of extraction, and lays the foundation for the industrial extraction.

  4. Nutrient removal and biomass production: advances in microalgal biotechnology for wastewater treatment.

    Science.gov (United States)

    Abinandan, Sudharsanam; Subashchandrabose, Suresh R; Venkateswarlu, Kadiyala; Megharaj, Mallavarapu

    2018-05-17

    Owing to certain drawbacks, such as energy-intensive operations in conventional modes of wastewater treatment (WWT), there has been an extensive search for alternative strategies in treatment technology. Biological modes for treating wastewaters are one of the finest technologies in terms of economy and efficiency. An integrated biological approach with chemical flocculation is being conventionally practiced in several-sewage and effluent treatment plants around the world. Overwhelming responsiveness to treat wastewaters especially by using microalgae is due to their simplest photosynthetic mechanism and ease of acclimation to various habitats. Microalgal technology, also known as phycoremediation, has been in use for WWT since 1950s. Various strategies for the cultivation of microalgae in WWT systems are evolving faster. However, the availability of innovative approaches for maximizing the treatment efficiency, coupled with biomass productivity, remains the major bottleneck for commercialization of microalgal technology. Investment costs and invasive parameters also delimit the use of microalgae in WWT. This review critically discusses the merits and demerits of microalgal cultivation strategies recently developed for maximum pollutant removal as well as biomass productivity. Also, the potential of algal biofilm technology in pollutant removal, and harvesting the microalgal biomass using different techniques have been highlighted. Finally, an economic assessment of the currently available methods has been made to validate microalgal cultivation in wastewater at the commercial level.

  5. Myths and facts on wastewater injection, hydraulic fracturing, enhanced oil recovery, and induced seismicity

    Science.gov (United States)

    Rubinstein, Justin L.; Mahani, Alireza Babaie

    2015-01-01

    The central United States has undergone a dramatic increase in seismicity over the past 6 years (Fig. 1), rising from an average of 24 M≥3 earthquakes per year in the years 1973–2008 to an average of 193 M≥3 earthquakes in 2009–2014, with 688 occurring in 2014 alone. Multiple damaging earthquakes have occurred during this increase including the 2011 M 5.6 Prague, Oklahoma, earthquake; the 2011 M 5.3 Trinidad, Colorado, earthquake; and the 2011M 4.7 Guy‐Greenbrier, Arkansas, earthquake. The increased seismicity is limited to a few areas and the evidence is mounting that the seismicity in many of these locations is induced by the deep injection of fluids from nearby oil and gas operations. Earthquakes that are caused by human activities are known as induced earthquakes. Most injection operations, though, do not appear to induce earthquakes. Although the message that these earthquakes are induced by fluid injection related to oil and gas production has been communicated clearly, there remains confusion in the popular press beyond this basic level of understanding.

  6. Produced water: Market and global trends - oil production - water production - choice of technology

    International Nuclear Information System (INIS)

    Robertson, Steve

    2006-01-01

    The presentation discusses various aspects of the world oil production, the energy demand, the future oil supply, the oil prices and the production growth. Some problems with produced water are also discussed as well as aspects of the market for produced water technology (tk)

  7. Oils; lubricants; paraffin-wax compositions; hydrocarbon condensation products

    Energy Technology Data Exchange (ETDEWEB)

    1934-04-04

    Petroleum hydrocarbons such as gasoline, kerosene, Diesel fuel oil, lubricating-oil, and paraffin wax, and like hydrocarbons such as are obtainable from shale oil and by the hydrogenation of carbonaceous materials, are improved by addition of products obtained by condensing a cyclic hydrocarbon with a saturated dihalogen derivative of an aliphatic hydrocarbon containing less than five carbon atoms. The addition of the condensation products increases the viscosity of the hydrocarbon oils specified, and is particularly useful in the case of lubricating-oils; addition of the condensation products to paraffin wax increases the transparency and adherent properties of the wax, and is useful in the manufacture of moulded articles such as candles; the products may also be used in solid lubricating-compositions.

  8. The Necessity of a Graded Tariff System between Crude Oil and Oil Products

    Energy Technology Data Exchange (ETDEWEB)

    Kang, B.R. [SK Corporation, Seoul (Korea)

    2002-06-01

    Even though the graded tariff system between crude oil and oil products has been continuously insisted by oil refining companies since the export and import liberalization of 1997, and its necessity has been admitted by the government, press, and academia, the expanded implementation of the graded tariff system has not been yet realized. Some people says that the graded tariff system between crude oil and oil products is a kind of desperate plans, which oil refining companies suggests to stop the importing companies' rapid growth, so it will eventually restrict the competition of the domestic oil market due to the withering of importing companies. However, the graded tariff system between crude oil and oil products should have been enforced in 1997 as a complementary measure of the import liberalization like other industries or the advanced countries' cases. It is the basic tariff principle that the low tariff is levied on raw materials and the high tariff on final products in order to protect domestic industry. The remaining things are just to form the sympathy and to agree socially for the reorganization of tariff structure in the reasonable way. It is not desirable to make a fool mistake such as a proverb; t is too late to shut the stable door after the horse has bolted. owing to the unreasonable tariff system.

  9. Lipid production from tapioca wastewater by culture of Scenedesmus sp. with simultaneous BOD, COD and nitrogen removal

    Science.gov (United States)

    Romaidi; Hasanudin, Muhammad; Kholifah, Khusnul; Maulidiyah, Alik; Putro, Sapto P.; Kikuchi, Akira; Sakaguchi, Toshifumi

    2018-05-01

    The use of microalgae to produce biodiesel or possibly remove nutrients from industrial wastewater has gained important attention during recent years due to their photosynthetic rate and its versatile nature to grow in various wastewater systems. In this study, a microalgae, Scenedesmus sp., was cultured to enhance the lipid production and nutrients removal from tapioca wastewater sample. To assess lipid production, Scenedesmus sp. was cultured in different concentration of tapioca wastewater sample (from 0 to 100 %), and nutrient removal including BOD, COD, NH4, NO2, NO3 level by Scenedesmus sp. was assessed in 100% of tapioca wastewater culture. After 8 days of culture, it was found out that 50% of tapioca wastewater sample resulted in highest concentration of lipid content than that of the other concentrations. The level of environment indicator as nutrient removal such as BOD, COD, NH4, NO2, NO3 were also decreased up to 74%, 72%, 95%, 91%, and 91%, respectively. The pH condition changed from initial condition acidic (pH: 4) to neutral or basic condition (pH: 7-8) as recommended in wastewater treatment system. This research provided a novel approach and achieved efficient simultaneous lipid production and nutrients removal from tapioca wastewater sample by Scenedesmus’s culture system.

  10. Conceptual design and techno-economic evaluation of efficient oil shale refinery processes ingratiated with oil and gas products upgradation

    International Nuclear Information System (INIS)

    Yang, Qingchun; Qian, Yu; Zhou, Huairong; Yang, Siyu

    2016-01-01

    Highlights: • Three integrated oil shale refinery processes are proposed. • Techno-economic performance of three proposed processes is conducted and compared. • Competitiveness of the three proposed processes is investigated at different scenarios. • A development direction for oil shale refinery industry is suggested. - Abstract: Compared with the petrochemical industry, oil shale refinery industry is still relatively backward and has many shortcomings, such as poor quality of shale oil, inefficient utilization of retorting gas, and the unsatisfactory economic performance. In the situation of the low oil price, many oil shale refinery plants are forced to stop or cut production. Thus, oil shale industry is facing a severe problem. How to relieve monetary loss or turn it into profits? This paper proposes three integrated oil shale refinery processes: an integrated with hydrogen production from retorting gas, an integrated with hydrogenation of shale oil, and an integrated with hydrogen production and oil hydrogenation. The techno-economic performance of the three different processes is conducted and compared with that of a conventional oil shale process. Results show the exergy destruction ratio of the oil shale process integrated with hydrogen production from retorting gas is the least, 41.6%, followed by the oil shale process integrated with hydrogen production and oil hydrogenation, 45.9%. Furthermore, these two proposed processes have the best economic performance. Especially they can turn losses of the conventional oil shale process into profits at the situation of low oil price. The oil shale process integrated with hydrogen production from retorting gas is recommended to the oil shale plants which use the oil shale with oil content lower than 12.9%, while the plants using oil shale with oil content higher than 12.9% are better to select the oil shale process integrated with hydrogen production and oil hydrogenation.

  11. Radiotracer investigations in oil production and water injection wells

    International Nuclear Information System (INIS)

    Eapen, A.C.; Jain, S.K.; Kirti

    1977-01-01

    Injection of gamma emitting radiotracers into oil wells followed by logging provides information on several aspects such as the identification of zones of seepage of water in the water injection wells and also the location of source of water entering oil producting wells. The experience gained in the application of bromine-82 and rubidium-86 as radiotracers in such studies at the Ankleshwar and Kalol oil fields in Gujarat and Nazira in Assam has been briefly reported. (author)

  12. Features of electric drive sucker rod pumps for oil production

    Science.gov (United States)

    Gizatullin, F. A.; Khakimyanov, M. I.; Khusainov, F. F.

    2018-01-01

    This article is about modes of operation of electric drives of downhole sucker rod pumps. Downhole oil production processes are very energy intensive. Oil fields contain many oil wells; many of them operate in inefficient modes with significant additional losses. Authors propose technical solutions to improve energy performance of a pump unit drives: counterweight balancing, reducing of electric motor power, replacing induction motors with permanent magnet motors, replacing balancer drives with chain drives, using of variable frequency drives.

  13. Development of taxation system for oil production companies in Russia

    Science.gov (United States)

    Salmina, S. V.; Sboeva, I. M.; Selivanovskaya, J. I.; Khafizova, A. R.; Fomin, V. P.

    2018-01-01

    The present article is devoted to the taxation system for oil production companies in Russia. The role of oil production companies in the realization of the fiscal function of the state is shown. Tax and due receipts at the consolidated budget of the Russian Federation from major economic sectors in the years 2013-2015 are presented and analysed. An investigation of oil production taxation peculiarities is carried out. In particular, mineral extraction tax analysis is made, the said tax being one of the basic taxes paid by oil production companies. The authors come to a conclusion that mineral extraction tax in Russia needs reforming. Based on the investigation realized possible ways of taxation system development in respect of oil production companies in Russia are proposed. Thus, taking into account the fact that oil industry is very important for budget revenue formation, initially it is planned to test the new taxation system principles in a limited number of deposits, so called ‘pilot projects’. For highly profitable minefield deposits it is planned to introduce progressive and regressive index, varying depending on oil prices. Within the framework of the investigation the authors come to a conclusion that it is necessary to introduce gradually the taxation system based on the definition of surplus profit depending on the cost effectiveness and taking into account oil prices.

  14. A review of wastewater handling in the Arctic with special reference to Pharmaceuticals and Personal Care Products (PPCPs) and microbial pollution

    DEFF Research Database (Denmark)

    Gunnarsdottir, Ragnhildur; Jenssen, Petter Deinboll; Jensen, Pernille Erland

    2013-01-01

    Treatment of wastewater is often inadequate or completely lacking in Arctic regions. Wastewater contains different kinds of substances that can be harmful for the environment and human health, including residues of pharmaceuticals and personal care products. Bioaccumulation and biomagnifications ...

  15. Production of Detergent from Castor Oil

    Directory of Open Access Journals (Sweden)

    Abubakar Garba ISAH

    2006-07-01

    Full Text Available This research work was carried out with the objective of extraction of oil from castor seeds and its utilization to produce a synthetic detergent. Solvent extraction method was employed in extracting the oil and the total percent oil yield was found to be 23.8%. The experimentally determined saponification value of the oil was 183.7275mgKOH/g of oil. The detergent efficiency, determined as a measure of the foamability of the detergent was found to be 2.6cm. The pH tests revealed mildly basic properties. The color, scent and efficiency of the detergent were improved with the addition of bleaching agent, perfume and foaming agents respectively.

  16. Canadian crude oil production and supply forecast 2006-2020

    International Nuclear Information System (INIS)

    2006-05-01

    In order to enable members to plan for pipeline capacity requirements for transporting Canadian crude oil to markets, the Canadian Association of Petroleum Producers (CAPP) 2006-2020 crude oil production and supply forecast provides a long-range outlook of Canadian crude oil production. It provides a forecast of supply and demand for both western and eastern Canada. Because offshore eastern oil production does not rely on pipeline access to reach markets, the analysis primarily focuses on western Canadian production and supply. Over the next fifteen years, Alberta's oil sands provides the main source of growth in the western Canadian production forecast. A survey of CAPP members encompassing all oil sands projects was conducted. Survey responses reflect both planned and envisioned projects over a fifteen year period, although some of the envisioned projects have been risk adjusted by modifying the potential completion schedules for projects which are deemed more uncertain. Detailed tables are provided on forecast data. Three sets of tables are included to show production, two supply scenarios and a high level assessment of the need for incremental pipeline capacity. The report also discusses delays and risk factors that could slow the pace of oil sands development and the corresponding increase in production being forecast in the base case. 16 tabs

  17. Explosively fracturing a productive oil and gas formation

    Energy Technology Data Exchange (ETDEWEB)

    Brandon, C W

    1966-06-23

    In this method of fracturing an oil- or gas-producing strata, a portion of the formation adjacent to, but separated from, the producing strata is fractured. Explosives are then introduced into the fracture in this portion of the formation and thereafter detonated to fracture the productive strata. Also claimed are a method of variably controlling the extent and force of the explosives used, and a method of increasing oil and gas production from a productive strata.

  18. Production and Characterization of Biodiesel from Tung Oil

    Science.gov (United States)

    Park, Ji-Yeon; Kim, Deog-Keun; Wang, Zhong-Ming; Lu, Pengmei; Park, Soon-Chul; Lee, Jin-Suk

    The feasibility of biodiesel production from tung oil was investigated. The esterification reaction of the free fatty acids of rung oil was performed using Amberlyst-15. Optimal molar ratio of methanol to oil was determined to be 7.5:1, and Amberlyst-15 was 20.8wt% of oil by response surface methodology. Under these reaction conditions, the acid value of rung oil was reduced to 0.72mg KOH/g. In the range of the molar equivalents of methanol to oil under 5, the esterification was strongly affected by the amount of methanol but not the catalyst. When the molar ratio of methanol to oil was 4.1:1 and Amberlyst-15 was 29.8wt% of the oil, the acid value decreased to 0.85mg KOH/g. After the transesterification reaction of pretreated rung oil, the purity of rung biodiesel was 90.2wt%. The high viscosity of crude rung oil decreased to 9.8mm2/s at 40 °C. Because of the presence of eleostearic acid, which is a main component of tung oil, the oxidation stability as determined by the Rancimat method was very low, 0.5h, but the cold filter plugging point, -11 °C, was good. The distillation process did not improve the fatty acid methyl ester content and the viscosity.

  19. Net energy yield from production of conventional oil

    International Nuclear Information System (INIS)

    Dale, Michael; Krumdieck, Susan; Bodger, Pat

    2011-01-01

    Historic profitability of bringing oil to market was profound, but most easy oil has been developed. Higher cost resources, such as tar sands and deep off-shore, are considered the best prospects for the future. Economic modelling is currently used to explore future price scenarios commensurate with delivering fuel to market. Energy policy requires modelling scenarios capturing the complexity of resource and extraction aspects as well as the economic profitability of different resources. Energy-return-on-investment (EROI) expresses the profitability of bringing energy products to the market. Net energy yield (NEY) is related to the EROI. NEY is the amount of energy less expenditures necessary to deliver a fuel to the market. This paper proposes a pattern for EROI of oil production, based on historic oil development trends. Methodology and data for EROI is not agreed upon. The proposed EROI function is explored in relation to the available data and used to attenuate the International Energy Agency (IEA) world oil production scenarios to understand the implications of future declining EROI on net energy yield. The results suggest that strategies for management and mitigation of deleterious effects of a peak in oil production are more urgent than might be suggested by analyses focussing only on gross production. - Highlights: → Brief introduction to methodological issues concerning net energy analysis. → Description of EROI function over the whole production cycle of an energy resource. → Calibration of this function to EROI data from historic oil production. → Application to determine the net energy yield from current global oil production. → Calculation of net energy yield from IEA projections of future oil production.

  20. OPEC and Venezuelan oil production. Evidence against a cartel hypothesis

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, Douglas B.; Pippenger, Michael K. [Department of Economics, University of Alaska Fairbanks, Fairbanks, AK (United States)

    2010-10-15

    This study revisits the OPEC cartel hypothesis using a case study. A test is conducted to see if Venezuela has its production Granger cause its OPEC quota or whether the OPEC quota for Venezuela Granger causes Venezuelan production. The results show both occur at different times. In the short run, OPEC's oil production quota for Venezuela Granger causes Venezuelan production. However, shortly after cuts, Venezuela cheats on agreements, suggesting a tit-for-tat oligopoly game, which is not anti-competitive. In the long run, we show that Venezuelan oil production Granger causes OPEC's quota for Venezuela, but not vice versa. Having Venezuelan oil production Granger cause OPEC quotas for Venezuela in the long run suggests OPEC does not coordinate outputs as much as it reacts to them. The evidence suggests Venezuela is not a part of an OPEC anti-competitive syndicate even though we show that Venezuelan oil production is low. An alternative explanation for why Venezuela and possibly other OPEC members have low oil production outputs is that institutions and risk aversion, not cartel participation, is the cause. A vector error correction model shows that there is no tendency for Venezuelan oil production to converge to OPEC's quota for Venezuela. (author)

  1. OPEC and Venezuelan oil production: Evidence against a cartel hypothesis

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, Douglas B., E-mail: DBReynolds@Alaska.ed [Department of Economics, University of Alaska Fairbanks, Fairbanks, AK (United States); Pippenger, Michael K. [Department of Economics, University of Alaska Fairbanks, Fairbanks, AK (United States)

    2010-10-15

    This study revisits the OPEC cartel hypothesis using a case study. A test is conducted to see if Venezuela has its production Granger cause its OPEC quota or whether the OPEC quota for Venezuela Granger causes Venezuelan production. The results show both occur at different times. In the short run, OPEC's oil production quota for Venezuela Granger causes Venezuelan production. However, shortly after cuts, Venezuela cheats on agreements, suggesting a tit-for-tat oligopoly game, which is not anti-competitive. In the long run, we show that Venezuelan oil production Granger causes OPEC's quota for Venezuela, but not vice versa. Having Venezuelan oil production Granger cause OPEC quotas for Venezuela in the long run suggests OPEC does not coordinate outputs as much as it reacts to them. The evidence suggests Venezuela is not a part of an OPEC anti-competitive syndicate even though we show that Venezuelan oil production is low. An alternative explanation for why Venezuela and possibly other OPEC members have low oil production outputs is that institutions and risk aversion, not cartel participation, is the cause. A vector error correction model shows that there is no tendency for Venezuelan oil production to converge to OPEC's quota for Venezuela.

  2. OPEC and Venezuelan oil production: Evidence against a cartel hypothesis

    International Nuclear Information System (INIS)

    Reynolds, Douglas B.; Pippenger, Michael K.

    2010-01-01

    This study revisits the OPEC cartel hypothesis using a case study. A test is conducted to see if Venezuela has its production Granger cause its OPEC quota or whether the OPEC quota for Venezuela Granger causes Venezuelan production. The results show both occur at different times. In the short run, OPEC's oil production quota for Venezuela Granger causes Venezuelan production. However, shortly after cuts, Venezuela cheats on agreements, suggesting a tit-for-tat oligopoly game, which is not anti-competitive. In the long run, we show that Venezuelan oil production Granger causes OPEC's quota for Venezuela, but not vice versa. Having Venezuelan oil production Granger cause OPEC quotas for Venezuela in the long run suggests OPEC does not coordinate outputs as much as it reacts to them. The evidence suggests Venezuela is not a part of an OPEC anti-competitive syndicate even though we show that Venezuelan oil production is low. An alternative explanation for why Venezuela and possibly other OPEC members have low oil production outputs is that institutions and risk aversion, not cartel participation, is the cause. A vector error correction model shows that there is no tendency for Venezuelan oil production to converge to OPEC's quota for Venezuela.

  3. Oil Fields, Oil and gas production platforms are potential source for oil spills and may interfere with mechanical means to clean up oil spills., Published in 1998, 1:24000 (1in=2000ft) scale, Louisiana State University (LSU).

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Oil Fields dataset current as of 1998. Oil and gas production platforms are potential source for oil spills and may interfere with mechanical means to clean up oil...

  4. The peak of oil production-Timings and market recognition

    International Nuclear Information System (INIS)

    Almeida, Pedro de; Silva, Pedro D.

    2009-01-01

    Energy is essential for present societies. In particular, transportation systems depend on petroleum-based fuels. That world oil production is set to pass a peak is now a reasonably accepted concept, although its date is far from consensual. In this work, we analyze the true expectations of the oil market participants about the future availability of this fundamental energy source. We study the evolution through time of the curves of crude oil futures prices, and we conclude that the market participants, among them the crude oil producers, already expect a near-term peak of oil production. This agrees with many technical predictions for the date of peak production, including our own, that point to peak dates around the end of the present decade. If this scenario is confirmed, it can cause serious social and economical problems because societies will have little time to perform the necessary adjustments

  5. Biohydrogen production from purified terephthalic acid (PTA) processing wastewater by anaerobic fermentation using mixed microbial communities

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Ge-Fu; Wu, Peng; Wei, Qun-Shan; Lin, Jian-yi; Liu, Hai-Ning [Key Lab of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Gao, Yan-Li [China University of Geosciences, Wuhan 430074 (China)

    2010-08-15

    Purified terephthalic acid (PTA) processing wastewater was evaluated as a fermentable substrate for hydrogen (H{sub 2}) production with simultaneous wastewater treatment by dark-fermentation process in a continuous stirred-tank reactor (CSTR) with selectively enriched acidogenic mixed consortia under continuous flow condition in this paper. The inoculated sludge used in the reactor was excess sludge taken from a second settling tank in a local wastewater treatment plant. Under the conditions of the inoculants not less than 6.3 gVSS/L, the organic loading rate (OLR) of 16 kgCOD/m{sup 3} d, hydraulic retention time (HRT) of 6 h and temperature of (35 {+-} 1) C, when the pH value, alkalinity and oxidation-reduction potential (ORP) of the effluent ranged from 4.2 to 4.4, 280 to 350 mg CaCO{sub 3}/L, and -220 to -250 mV respectively, soluble metabolites were predominated by acetate and ethanol, with smaller quantities of propionate, butyrate and valerate. Stable ethanol-type fermentation was formed with the sum of ethanol and acetate concentration ratio of 70.31% to the total liquid products after 25 days operation. The H{sub 2} volume content was estimated to be 48-53% of the total biogas and the biogas was free of methane throughout the study. The average biomass concentration was estimated to be 10.82 gVSS/L, which favored H{sub 2} production efficiently. The rate of chemical oxygen demand (COD) removal reached at about 45% and a specific H{sub 2} production rate achieved 0.073 L/gMLVSS d in the study. This CSTR system showed a promising high-efficient bioprocess for H{sub 2} production from high-strength chemical wastewater. (author)

  6. Process development for the removal and recovery of hazardous dye erythrosine from wastewater by waste materials-Bottom Ash and De-Oiled Soya as adsorbents

    Energy Technology Data Exchange (ETDEWEB)

    Mittal, Alok [Department of Applied Chemistry, Maulana Azad National Institute of Technology, Bhopal 462007 (India)]. E-mail: aljymittal@yahoo.co.in; Mittal, Jyoti [Department of Applied Chemistry, Maulana Azad National Institute of Technology, Bhopal 462007 (India); Kurup, Lisha [Department of Applied Chemistry, Maulana Azad National Institute of Technology, Bhopal 462007 (India); Singh, A.K. [Department of Applied Chemistry, University Institute of Technology, RGPV, Bhopal 462036 (India)

    2006-11-02

    Erythrosine is a water-soluble xanthene class of dye. It is widely used as colorant in foods, textiles, drugs and cosmetics. It is highly toxic, causes various types of allergies, thyroid activities, carcinogenicity, DNA damage behaviour, neurotoxicity and xenoestrogen nature in the humans and animals. The photochemical and biochemical degradation of the erythrosine is not recommended due to formation of toxic by-products. The present paper is an attempt to remove erythrosine from wastewater using adsorption over Bottom Ash-a power plant waste and De-Oiled Soya-an agricultural waste. Under the batch studies, effect of concentration of dye, temperature, pH of the solution, dosage of adsorbents, sieve size of adsorbents, etc., have been studied for the uptake of the dye over both adsorbents. The adsorption process verifies Langmuir and Freundlich adsorption isotherms in both the cases and based on the data different thermodynamic parameters have been evaluated. Batch studies also include kinetic measurements, rate constant study, mass transfer behaviour and establishment of mechanistic pathway for both the cases. For the bulk removal of the dye column operations have been carried out and breakthrough capacities of the Bottom Ash and De-Oiled Soya columns have been calculated. Attempts have also been made for the recovery of the adsorbed dye from exhausted columns by eluting dilute NaOH and more than 90% of the dye was recovered.

  7. Process development for the removal and recovery of hazardous dye erythrosine from wastewater by waste materials-Bottom Ash and De-Oiled Soya as adsorbents

    International Nuclear Information System (INIS)

    Mittal, Alok; Mittal, Jyoti; Kurup, Lisha; Singh, A.K.

    2006-01-01

    Erythrosine is a water-soluble xanthene class of dye. It is widely used as colorant in foods, textiles, drugs and cosmetics. It is highly toxic, causes various types of allergies, thyroid activities, carcinogenicity, DNA damage behaviour, neurotoxicity and xenoestrogen nature in the humans and animals. The photochemical and biochemical degradation of the erythrosine is not recommended due to formation of toxic by-products. The present paper is an attempt to remove erythrosine from wastewater using adsorption over Bottom Ash-a power plant waste and De-Oiled Soya-an agricultural waste. Under the batch studies, effect of concentration of dye, temperature, pH of the solution, dosage of adsorbents, sieve size of adsorbents, etc., have been studied for the uptake of the dye over both adsorbents. The adsorption process verifies Langmuir and Freundlich adsorption isotherms in both the cases and based on the data different thermodynamic parameters have been evaluated. Batch studies also include kinetic measurements, rate constant study, mass transfer behaviour and establishment of mechanistic pathway for both the cases. For the bulk removal of the dye column operations have been carried out and breakthrough capacities of the Bottom Ash and De-Oiled Soya columns have been calculated. Attempts have also been made for the recovery of the adsorbed dye from exhausted columns by eluting dilute NaOH and more than 90% of the dye was recovered

  8. Photodegradation kinetics and transformation products of ketoprofen, diclofenac and atenolol in pure water and treated wastewater

    International Nuclear Information System (INIS)

    Salgado, R.; Pereira, V.J.; Carvalho, G.; Soeiro, R.; Gaffney, V.; Almeida, C.; Cardoso, V. Vale; Ferreira, E.; Benoliel, M.J.

    2013-01-01

    Highlights: ► Direct UV photolysis of 3 pharmaceuticals in pure and waste water was investigated. ► Ketoprofen has higher photodegradion kinetics, followed by diclofenac and atenolol. ► MP/UV photodegradation products were identified for the 3 compounds. ► Photodegradation pathways were proposed to explain the obtained products. ► The persistent photoproducts were identified for each compound. -- Abstract: Pharmaceutical compounds such as ketoprofen, diclofenac and atenolol are frequently detected at relatively high concentrations in secondary effluents from wastewater treatment plants. Therefore, it is important to assess their transformation kinetics and intermediates in subsequent disinfection processes, such as direct ultraviolet (UV) irradiation. The photodegradation kinetics of these compounds using a medium pressure (MP) lamp was assessed in pure water, as well as in filtered and unfiltered treated wastewater. Ketoprofen had the highest time- and fluence-based rate constants in all experiments, whereas atenolol had the lowest values, which is consistent with the corresponding decadic molar absorption coefficient and quantum yield. The fluence-based rate constants of all compounds were evaluated in filtered and unfiltered wastewater matrices as well as in pure water. Furthermore, transformation products of ketoprofen, diclofenac and atenolol were identified and monitored throughout the irradiation experiments, and photodegradation pathways were proposed for each compound. This enabled the identification of persistent transformation products, which are potentially discharged from WWTP disinfection works employing UV photolysis

  9. Photodegradation kinetics and transformation products of ketoprofen, diclofenac and atenolol in pure water and treated wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Salgado, R. [REQUIMTE/CQFB, Chemistry Department, FCT, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); ESTS-IPS, Escola Superior de Tecnologia de Setúbal do Instituto Politécnico de Setúbal, Rua Vale de Chaves, Campus do IPS, Estefanilha, 2910-761 Setúbal (Portugal); Pereira, V.J. [Instituto de Biologia Experimental e Tecnológica (IBET), Av. da República (EAN), 2784-505 Oeiras (Portugal); Instituto de Tecnologia Química e Biológica (ITQB) – Universidade Nova de Lisboa (UNL), Av. da República, Estação Agronómica Nacional, 2780-157 Oeiras, 5 Portugal (Portugal); Carvalho, G., E-mail: gs.carvalho@fct.unl.pt [REQUIMTE/CQFB, Chemistry Department, FCT, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Instituto de Biologia Experimental e Tecnológica (IBET), Av. da República (EAN), 2784-505 Oeiras (Portugal); Soeiro, R. [REQUIMTE/CQFB, Chemistry Department, FCT, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Gaffney, V.; Almeida, C. [Institute for Medicines and Pharmaceutical Sciences (iMed.UL), Faculdade de Farmácia da Universidade de Lisboa (FFUL), Av. Prof. Gama Pinto, 1600-049 Lisboa (Portugal); Cardoso, V. Vale; Ferreira, E.; Benoliel, M.J. [Empresa Portuguesa das Águas Livres, S.A., Direcção de Controlo de Qualidade da Água, Laboratório Central, Avenida de Berlim, 15, 1800-031 Lisboa (Portugal); and others

    2013-01-15

    Highlights: ► Direct UV photolysis of 3 pharmaceuticals in pure and waste water was investigated. ► Ketoprofen has higher photodegradion kinetics, followed by diclofenac and atenolol. ► MP/UV photodegradation products were identified for the 3 compounds. ► Photodegradation pathways were proposed to explain the obtained products. ► The persistent photoproducts were identified for each compound. -- Abstract: Pharmaceutical compounds such as ketoprofen, diclofenac and atenolol are frequently detected at relatively high concentrations in secondary effluents from wastewater treatment plants. Therefore, it is important to assess their transformation kinetics and intermediates in subsequent disinfection processes, such as direct ultraviolet (UV) irradiation. The photodegradation kinetics of these compounds using a medium pressure (MP) lamp was assessed in pure water, as well as in filtered and unfiltered treated wastewater. Ketoprofen had the highest time- and fluence-based rate constants in all experiments, whereas atenolol had the lowest values, which is consistent with the corresponding decadic molar absorption coefficient and quantum yield. The fluence-based rate constants of all compounds were evaluated in filtered and unfiltered wastewater matrices as well as in pure water. Furthermore, transformation products of ketoprofen, diclofenac and atenolol were identified and monitored throughout the irradiation experiments, and photodegradation pathways were proposed for each compound. This enabled the identification of persistent transformation products, which are potentially discharged from WWTP disinfection works employing UV photolysis.

  10. Biogas production from UASB and polyurethane carrier reactors treating sisal processing wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Rubindamayugi, M S.T.; Salakana, L K.P. [Univ. of Dar es Salaam, Faculty of Science, Applied Microbiology Unit (Tanzania, United Republic of)

    1998-12-31

    The fundamental benefits which makes anaerobic digestion technology (ADT) attractive to the poor developing include the low cost and energy production potential of the technology. In this study the potential of using UASB reactor and Polyurethane Carrier Reactor (PCR) as pollution control and energy recovery systems from sisal wastewater were investigated in lab-scale reactors. The PCR demonstrated the shortest startup period, whereas the UASB reactor showed the highest COD removal efficiency 79%, biogas production rate (4.5 l biogas/l/day) and process stability than the PCR under similar HRT of 15 hours and OLR of 8.2 g COD/l/day. Both reactor systems became overloaded at HRT of 6 hours and OLR of 15.7 g COD/l/day, biogas production ceased and reactors acidified to pH levels which are inhibiting to methanogenesis. Based on the combined results on reactor performances, the UASB reactor is recommended as the best reactor for high biogas production and treatment efficiency. It was estimated that a large-scale UASB reactor can be designed under the same loading conditions to produce 2.8 m{sup 3} biogas form 1 m{sup 3} of wastewater of 5.16 kg COD/m{sup 3}. Wastewater from one decortication shift can produce 9,446 m{sup 3} og biogas. The energy equivalent of such fuel energy is indicated. (au)

  11. Biogas production from UASB and polyurethane carrier reactors treating sisal processing wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Rubindamayugi, M.S.T.; Salakana, L.K.P. [Univ. of Dar es Salaam, Faculty of Science, Applied Microbiology Unit (Tanzania, United Republic of)

    1997-12-31

    The fundamental benefits which makes anaerobic digestion technology (ADT) attractive to the poor developing include the low cost and energy production potential of the technology. In this study the potential of using UASB reactor and Polyurethane Carrier Reactor (PCR) as pollution control and energy recovery systems from sisal wastewater were investigated in lab-scale reactors. The PCR demonstrated the shortest startup period, whereas the UASB reactor showed the highest COD removal efficiency 79%, biogas production rate (4.5 l biogas/l/day) and process stability than the PCR under similar HRT of 15 hours and OLR of 8.2 g COD/l/day. Both reactor systems became overloaded at HRT of 6 hours and OLR of 15.7 g COD/l/day, biogas production ceased and reactors acidified to pH levels which are inhibiting to methanogenesis. Based on the combined results on reactor performances, the UASB reactor is recommended as the best reactor for high biogas production and treatment efficiency. It was estimated that a large-scale UASB reactor can be designed under the same loading conditions to produce 2.8 m{sup 3} biogas form 1 m{sup 3} of wastewater of 5.16 kg COD/m{sup 3}. Wastewater from one decortication shift can produce 9,446 m{sup 3} og biogas. The energy equivalent of such fuel energy is indicated. (au)

  12. Market analysis of shale oil co-products. Summary report

    Energy Technology Data Exchange (ETDEWEB)

    1980-12-01

    This study examines the potential for separating, upgrading and marketing sodium mineral co-products together with shale oil production. The co-products investigated are soda ash and alumina which are derived from the minerals nahcolite and dawsonite. Five cases were selected to reflect the variance in mineral and shale oil content in the identified resource. In the five cases examined, oil content of the shale was varied from 20 to 30 gallons per ton. Two sizes of facilities were analyzed for each resource case to determine economies of scale between a 15,000 barrel per day demonstration unit and a 50,000 barrel per day full sized plant. Three separate pieces of analysis were conducted in this study: analysis of manufacturing costs for shale oil and co-products; projection of potential world markets for alumina, soda ash, and nahcolite; and determination of economic viability and market potential for shale co-products.

  13. Liquid oil production from shale gas condensate reservoirs

    Science.gov (United States)

    Sheng, James J.

    2018-04-03

    A process of producing liquid oil from shale gas condensate reservoirs and, more particularly, to increase liquid oil production by huff-n-puff in shale gas condensate reservoirs. The process includes performing a huff-n-puff gas injection mode and flowing the bottom-hole pressure lower than the dew point pressure.

  14. Characteristics of small-scale palm oil production enterprise in ...

    African Journals Online (AJOL)

    The study examined characteristics of small-scale palm oil production enterprise in Anambra State, Nigeria. All the palm oil producers in Anambra State formed the population of the study. Multi-stage sampling technique was used to select 120 respondents for the study. Data were collected from primary source through ...

  15. Production of biodiesel by transesterification of refined soybean oil ...

    African Journals Online (AJOL)

    This study focused on the production of biodiesel via transesterification of refined soybean oil obtained locally. Sodium hydroxide was used as the alkali catalyst and methanol (as alcohol) was used in the transesterification process due to its low cost. The methanol-to-oil molar ratio was maintained at 6:1. The effect of ...

  16. Economic Analysis of Production of Essential Oil using Steam ...

    African Journals Online (AJOL)

    From the profitability analysis and measure of return on investment carried out based on the various assumptions and projections made, it was quite obvious that the production of essential oil using steam distillation technology is highly profitable which should be attractive to potential investors. Keywords: Essential oil ...

  17. Toxicity of crude oil products and detergent on serum alkaline ...

    African Journals Online (AJOL)

    The comparative effect of exposing Clarias gariepinus juveniles (100.20 + 0.8g) to diferent concentrations of crude oil products and detergent were studied. Bonny Light Crude oil (BLCO), Premium motor spirit (PMS), Dual purpose kerosene (DPK) and Ariel Enzymax Detergent (AED) were respectively applied at three ...

  18. Oil Reservoir Production Optimization using Single Shooting and ESDIRK Methods

    DEFF Research Database (Denmark)

    Capolei, Andrea; Völcker, Carsten; Frydendall, Jan

    2012-01-01

    the injections and oil production such that flow is uniform in a given geological structure. Even in the case of conventional water flooding, feedback based optimal control technologies may enable higher oil recovery than with conventional operational strategies. The optimal control problems that must be solved...

  19. Oil production, oil prices, and macroeconomic adjustment under different wage assumptions

    International Nuclear Information System (INIS)

    Harvie, C.; Maleka, P.T.

    1992-01-01

    In a previous paper one of the authors developed a simple model to try to identify the possible macroeconomic adjustment processes arising in an economy experiencing a temporary period of oil production, under alternative wage adjustment assumptions, namely nominal and real wage rigidity. Certain assumptions were made regarding the characteristics of actual production, the permanent revenues generated from that oil production, and the net exports/imports of oil. The role of the price of oil, and possible changes in that price was essentially ignored. Here we attempt to incorporate the price of oil, as well as changes in that price, in conjunction with the production of oil, the objective being to identify the contribution which the price of oil, and changes in it, make to the adjustment process itself. The emphasis in this paper is not given to a mathematical derivation and analysis of the model's dynamics of adjustment or its comparative statics, but rather to the derivation of simulation results from the model, for a specific assumed case, using a numerical algorithm program, conducive to the type of theoretical framework utilized here. The results presented suggest that although the adjustment profiles of the macroeconomic variables of interest, for either wage adjustment assumption, remain fundamentally the same, the magnitude of these adjustments is increased. Hence to derive a more accurate picture of the dimensions of adjustment of these macroeconomic variables, it is essential to include the price of oil as well as changes in that price. (Author)

  20. Canadian operators boost heavy oil production

    International Nuclear Information System (INIS)

    Perdue, J.M.

    1996-01-01

    Recent technological advances in slurry pipelining, horizontal wells, and thermal recovery techniques have made recovery of Canadian heavy oil resources more economical. In addition, reduced government royalties have made investment in these difficult reservoirs more attractive. As a result, activity has increased in heavy-oil fields in Alberta and Saskatchewan. This paper review the various oil sand recovery projects under development in the area and the current government policies which are helping to develop them. The paper also provides brief descriptions of the equipment and technologies that have allowed a reduced cost in the development. Items discussed include surface mining techniques, horizontal drilling, reservoir engineering techniques, separation processes, and thermal recovery

  1. Microalgae biomass growth using primary treated wastewater as nutrient source and their potential use for lipids production

    Science.gov (United States)

    Frementiti, Anastacia; Aravantinou, Andriana F.; Manariotis, Ioannis D.

    2015-04-01

    The great demand for energy, the rising price of the crude oil and the rapid decrease of the supply of fossil fuels are the main reasons that have increased the interest for the production of fuels from renewable resources. Microalgae are considered to be the most promising new source of biomass and biofuels, since their lipid content in some cases is up to 70%. The microalgal growth and its metabolism processes are essential in wastewater treatment with many economical prospects. The aim of this work was to evaluate the algal production in a laboratory scale open pond. The pond had a working volume of 30 L and was fed with sterilized primary treated wastewater. Chlorococcum sp. was used as a model microalgal. Experiments were conducted under controlled environmental conditions in order to investigate the removal of nutrients, biomass growth, and lipids accumulation in microalgae. Chlorococcum sp. cultures behavior was investigated under batch, fill and draw, and continuous operation mode, at two different radiation intensities (100 and 200 μmol/m2s). The maximum biomass concentration of 630 mg/L was observed with the fill and draw mode. Moreover, the growth rates of microalgal biomass were depended on the influent nutrients concentration. Specifically, the phosphates were the limiting factor for biomass growth in continuous condition; the phosphates removal in this condition, reached a 100%. Chemical demand oxygen (COD) was not removed efficiently by Chlorococcum sp. since it was an autotrophic microalgal with no organic carbon demands for its growth. The lipids content in the dry weight of Chlorococcum sp. ranged from 1 to 9% depending on the concentration of nutrients and the operating conditions.

  2. Cyanobacteria cultivation in industrial wastewaters and biodiesel production from their biomass: a review.

    Science.gov (United States)

    Balasubramanian, Lavanya; Subramanian, Geetha; Nazeer, Thayiba Thanveer; Simpson, Hannah Shalini; Rahuman, Shifina T; Raju, Preetha

    2011-01-01

    As an alternative fuel biodiesel has become increasingly important due to diminishing petroleum reserves and adverse environmental consequences of exhaust gases from petroleum-fueled engines. Recently, research interest has focused on the production of biofuel from microalgae. Cyanobacteria appeared to be suitable candidates for cultivation in wastes and wastewaters because they produce biomass in satisfactory quantity and can be harvested relatively easily due to their size and structure. In addition, their biomass composition can be manipulated by several environmental and operational factors to produce biomass with concrete characteristics. Herein, we review the culture of cyanobacteria in wastewaters and also the potential resources that can be transformed into biodiesel successfully for meeting the ever-increasing demand for biodiesel production. Copyright © 2011 International Union of Biochemistry and Molecular Biology, Inc.

  3. Methane production as from the mixture of the urban solid waste lixiviate and municipal wastewater

    International Nuclear Information System (INIS)

    Monroy-Hermosillo, Oscar; Ramírez-Vives, Florina; Rodríguez-Pimentel, Reyna I.; Rodríguez-Pérez, Suyén

    2015-01-01

    The generation of solid wastes and wastewater in Mexico , as other countries, has increased considerably of late years, so its treatment is very important to reduce the pollution. In this work are presented the results on the anaerobic digestion of lixiviate generated with the hydrolysis and acidogenesis of the organic fraction of municipal solid waste recollected in the Universidad Autónoma Metropolitana-Unidad Iztapalapa coffee shop. Theses lixiviated were diluted with municipal wastewater to different organic loads (2,3-20 gCOD/L.d) and after treated anaerobically in UASB reactor. Biogas's average production in the last load of the UASB reactor was up to 12 L/L.d with an efficiency to remove COD on top of 90 % and a production of methane of 0,38 LCH4. gSSV-1. (author)

  4. Biological treatment of nitrate bearing wastewater from a uranium production plant

    International Nuclear Information System (INIS)

    Benear, A.K.; Kneip, R.W.

    1988-01-01

    The Feed Materials Production Center (FMPC) produces uranium metal products used for DOE defense programs resulting in the generation of nitrate-bearing wastewaters. To treat these wastewaters, a two-column fluidized bed biodenitrification facility (BDN) was constructed at the FMPC. The operation of the BDN resulted in substantial compliance with the design criteria limits for nitrate from July through November, 1987. Since the BDN surge lagoon (BSL) proved inadequate for providing nitrate concentration equalization, the BDN feed nitrate concentration fluctuated widely throughout this period of operation. BDN effluent caused a doubling of the hydraulic loading and a tripling of the organic loading on the FMPC sewage treatment plant (STP). Better control of the methanol feed to the BDN, coupled with reduced throughput and improved preaeration, caused a significant improvement in the operation of the STP. The overloading of the STP prompted a decision to add a stand-alone effluent treatment system to the BDN

  5. Anaerobic treatment of antibiotic production wastewater pretreated with enhanced hydrolysis: Simultaneous reduction of COD and ARGs.

    Science.gov (United States)

    Yi, Qizhen; Zhang, Yu; Gao, Yingxin; Tian, Zhe; Yang, Min

    2017-03-01

    The presence of high concentration antibiotics in wastewater can disturb the stability of biological wastewater treatment systems and promote generation of antibiotic resistance genes (ARGs) during the treatment. To solve this problem, a pilot system consisting of enhanced hydrolysis pretreatment and an up-flow anaerobic sludge bed (UASB) reactor in succession was constructed for treating oxytetracycline production wastewater, and the performance was evaluated in a pharmaceutical factory in comparison with a full-scale anaerobic system operated in parallel. After enhanced hydrolysis under conditions of pH 7 and 85 °C for 6 h, oxytetracycline production wastewater with an influent chemical oxygen demand (COD) of 11,086 ± 602 mg L -1 was directly introduced into the pilot UASB reactor. With the effective removal of oxytetracycline and its antibacterial potency (from 874 mg L -1 to less than 0.61 mg L -1 and from 900 mg L -1 to less than 0.84 mg L -1 , respectively) by the enhanced hydrolysis pretreatment, an average COD removal rate of 83.2%, 78.5% and 68.9% was achieved at an organic loading rate of 3.3, 4.8 and 5.9 kg COD m -3  d -1 , respectively. At the same time, the relative abundances of the total tetracycline (tet) genes and a mobile element (Class 1 integron (intI1)) in anaerobic sludge on day 96 were one order of magnitude lower than those in inoculated sludge on day 0 (P anaerobic system treating oxytetracycline production wastewater with an influent COD of 3720 ± 128 mg L -1 after dilution exhibited a COD removal of 51 ± 4% at an organic loading rate (OLR) 1.2 ± 0.2 kg m -3  d -1 , and a total tet gene abundance in sludge was five times higher than the pilot-scale system (P anaerobic treatment of oxytetracycline production wastewater containing high concentrations of oxytetracycline with significantly lower generation of ARGs. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Review on biofuel oil and gas production processes from microalgae

    International Nuclear Information System (INIS)

    Amin, Sarmidi

    2009-01-01

    Microalgae, as biomass, are a potential source of renewable energy, and they can be converted into energy such as biofuel oil and gas. This paper presents a brief review on the main conversion processes of microalgae becoming energy. Since microalgae have high water content, not all biomass energy conversion processes can be applied. By using thermochemical processes, oil and gas can be produced, and by using biochemical processes, ethanol and biodiesel can be produced. The properties of the microalgae product are almost similar to those of offish and vegetable oils, and therefore, it can be considered as a substitute of fossil oil.

  7. Production of synthetic hydrocarbon lube oil from highly waxy feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Xue, Q; Ding, Z; Zheng, Sh; Wu, W

    1980-01-01

    A feasible way to utilize the low value soft wax is to convert it into synthetic hydrocarbon lube oil by thermal cracking/polymerization route. The first commercial plant for this purpose has been in normal operation since 1970. It has been proved to be economically sound. The antioxidant response of the product polymer oil can be distinctly improved by hydro-refining. It has been found that the vacuum gas oil from highly waxy crude with or without furfural refining can be used as cracking stock. If high viscosity index polymer oil is desired, it is better to use slack wax as the cracking stock.

  8. Oil Production, The Price Crash and Uncertainty in Climate Change

    Science.gov (United States)

    Murray, J. W.

    2015-12-01

    World oil production increased to about 74 million barrels per day by January 2005, and was fairly constant until 2011 when it started to increase to 77.8 mb/d in 2014. This spectacular increase of 4 mb/d was almost entirely due to a sharp increase in production in the US from shale formations, called light tight oil (LTO). World oil production minus this increase in US LTO Production has been flat since 2005 at about 74 mb/d. When US production starts to decline, world oil production likely will as well. That surge is forecast to end soon because LTO is expensive to produce, the first year decline rates are extremely high requiring many new wells each year to maintain or increase production and the most productive locations have already been drilled. It is unprofitable for the Exploration and Production (E&P) companies. Full-year free cash flow has been negative for most tight oil E&P companies since 2009. The total negative cash flow for the 19 largest E&P companies totaled 10.5B in 2014. The surge in US LTO production created an imbalance in global supply and demand and resulted in a 50% decrease in the price of oil. The tight-oil producers who were are financially marginal at an oil price greater than 90 per barrel are even more so at the lower price. As a result the surge in US production of LTO is declining, making it unlikely that world oil production will exceed the present value of about 28 Gb/yr (equivalent to 75 mb/d) (175 EJ/yr). Many of the SRES (IPCC Special Report on Emission Scenarios) and RCP (IPCC Representative Concentration Pathways) projections (especially RCP 8.5 and 6) require CO2 emissions due to oil consumption in the range of 32 Gb/yr to 57 Gb/yr (200 to 350 EJ/yr). The higher values would require a doubling of world oil production. It is highly uncertain whether the higher CO2 scenarios will be reached. This is an element of uncertainty missing from most considerations of future climate change.

  9. Microbial community-based polyhydroxyalkanoates (PHAs) production from wastewater : Techno-economic analysis and ex-ante environmental assessment

    NARCIS (Netherlands)

    Fernandez Dacosta, Cora; Posada, John A.; Kleerebezem, Robbert; Cuellar, Maria C.; Ramirez, Andrea

    2015-01-01

    This work investigates the potential for polyhydroxybutyrate (PHB) production from wastewater, from a techno-economic and an environmental perspective, examining scale-up opportunities and bottlenecks prior to commercialisation. Conceptual process design, economic, environmental impacts and

  10. Evaluation of pharmaceuticals and personal care products with emphasis on anthelmintics in human sanitary waste, sewage, hospital wastewater, livestock wastewater and receiving water.

    Science.gov (United States)

    Sim, Won-Jin; Kim, Hee-Young; Choi, Sung-Deuk; Kwon, Jung-Hwan; Oh, Jeong-Eun

    2013-03-15

    We investigated 33 pharmaceuticals and personal care products (PPCPs) with emphasis on anthelmintics and their metabolites in human sanitary waste treatment plants (HTPs), sewage treatment plants (STPs), hospital wastewater treatment plants (HWTPs), livestock wastewater treatment plants (LWTPs), river water and seawater. PPCPs showed the characteristic specific occurrence patterns according to wastewater sources. The LWTPs and HTPs showed higher levels (maximum 3000 times in influents) of anthelmintics than other wastewater treatment plants, indicating that livestock wastewater and human sanitary waste are one of principal sources of anthelmintics. Among anthelmintics, fenbendazole and its metabolites are relatively high in the LWTPs, while human anthelmintics such as albendazole and flubendazole are most dominant in the HTPs, STPs and HWTPs. The occurrence pattern of fenbendazole's metabolites in water was different from pharmacokinetics studies, showing the possibility of transformation mechanism other than the metabolism in animal bodies by some processes unknown to us. The river water and seawater are generally affected by the point sources, but the distribution patterns in some receiving water are slightly different from the effluent, indicating the influence of non-point sources. Copyright © 2013 Elsevier B.V. All rights reserved.

  11. Potential reduction of carbon emissions from Crude Palm Oil production based on energy and carbon balances

    International Nuclear Information System (INIS)

    Patthanaissaranukool, Withida; Polprasert, Chongchin; Englande, Andrew J.

    2013-01-01

    Highlights: ► We evaluate energy and carbon equivalence from CPO production based on a CBM. ► Energy spent and produced via carbon movement from palm oil mill was determined. ► Scenarios were formulated to evaluate the potential reduction of carbon emission. ► Utilization of biomass from palm oil mill shows the high potential of C-reduction. -- Abstract: This study aimed to evaluate energy and carbon equivalences (CE) associated with palm oil milling and to evaluate sustainability alternatives for energy consumption. Appropriate ways to reduce carbon emissions were also evaluated. A field survey was carried out to quantify the input and output of energy and materials following the conceptual framework of a carbon-balanced model (CBM), which exclude other non-CO 2 greenhouse gases. Survey results indicate that the electrical energy consumption for daily mill start-up averaged 18.7 ± 5.4 kWh/ton Fresh Fruit Bunches (FFBs). This energy is equivalent to 114.4 ± 33.2 kWh/ton Crude Palm Oil (CPO) which was found to be offset by that generated in the mills using palm fiber as a solid fuel. Currently, organic residues contained in the wastewater are anaerobically converted to methane. The methane is used as fuel to generate electricity and sold to an outside grid network at a generation rate of 8.1 ± 2.1 kWh/ton FFB. Based on the CBM approach, carbon emissions observed from the use of fossil energy in palm oil milling were very small; however, total carbon emission from oil palm plantation and palm oil milling were found to be 12.3 kg CE/ton FFB, resulting in the net carbon reduction in CPO production of 2.8 kg CE/ton FFB or 53.7 kg CE/ha-y. Overall, the sum of C-reduction was found 1.2 times greater than that of C-emission. This figure can be increased up to 5.5, if all biomass by-products are used as fuel to generate electricity only. The full potential for carbon reduction from palm oil milling is estimated at 0.94 kW of electric power for every hectare of

  12. Biodiesel production from residual oils recovered from spent bleaching earth

    International Nuclear Information System (INIS)

    Huang, Yi-Pin; Chang, James I.

    2010-01-01

    This work was to study technical and economic feasibilities of converting residual oils recovered from spent bleaching earth generated at soybean oil refineries into useable biodiesel. Experimental results showed that fatty acids in the SBE residual oil were hexadecenoic acid (58.19%), stearic acid (21.49%) and oleic acid (20.32%), which were similar to those of vegetable oils. The methyl ester conversion via a transesterification process gave a yield between 85 and 90%. The biodiesel qualities were in reasonable agreement with both EN 14214 and ASTM D6751 standards. A preliminary financial analysis showed that the production cost of biodiesel from SBE oils was significantly lower than the pre-tax price of fossil diesel or those made of vegetable oils or waste cooking oils. The effects of the crude oil price and the investment on the production cost and the investment return period were also conducted. The result showed that the investment would return faster at higher crude oil price. (author)

  13. Controlled PVTS oil and gas production stimulation system

    Energy Technology Data Exchange (ETDEWEB)

    Ospina-Racines, E

    1970-02-01

    By completing oil- or gas-producing wells according to the PVTS method and energizing the flow of the oil-gas fluids in the reservoir with a small horse-power gas compressor at the wellhead, the following oil and gas production features are attained: (1) Original reservoir story energy conditions are restored, improved, used, and conserved while producing oil and/or gas. (2) The flow of oil or gas in the pay formation to the well bore is stimulated by gas compressor energy, outside of the reservoir system. The pressure drawdown is developed by gas-compressor energy in the well casing and not in the pay formation. (3) The stored energy of the reservoir is conserved while producing oil or gas. The potential energy (pressure) of the reservoir can be used to advantage up to bubble point of the virgin crude. (4) Producible reserves are increased from 4-to 5-fold by the conservation of reservoir energy. Present-day primary oil production practice yields a maximum of 20% of the oil in place by depleting the original reservoir energy. The PVTS system will yield over 80% + of oil in place. (5) Producible gas reserves can be increased greatly by establishing a low abandonment pressure at will. The principal features of the PVTS well mechanism and energy injection method are illustrated by a schematic diagram.

  14. Perspectives for pyrolysis oil production and market in Scandinavia

    International Nuclear Information System (INIS)

    Sipilae, K.; Oasmaa, A.; Solantausta, Y.; Arpiainen, V.; Nyroenen, T.

    1999-01-01

    Commercial power production from biomass is mainly based on various combustion technologies, new gasification technologies being on pilot and demonstration scale in Europe. From the market viewpoint, there will be an attractive and large market volume for small and medium-scale combined heat and power production (CHP) and for liquid bioenergy products in order to meet the Kyoto challenges in Europe by the year 2010. Biomass pyrolysis technology offers a novel method of converting solid biomass to a liquid product which can easily be transported, stored and utilised for electricity production by diesel engines and gas turbines. The overall efficiency in pyrolysis oil production can be increased from 65 to 90 % (LHV) by integrating the big-oil production to a conventional boiler plant, the-system identified by VTT. A modern diesel power plant has an efficiency of 40 - 44 % with a high power-to-heat ratio. Parallel to diesel power plants, the big-oil can be used in existing heating oil boilers with minor burner modifications. The paper comprises an overview of market assessments in Scandinavia and a summary of pyrolysis oil production, stability and properties tests. The challenge of today is to understand and improve the properties of pyrolysis oils in order to reach a 12-month storage time without any changes in the homogeneity of pyrolysis oils. Reliable operation of oil-fired boilers and diesel power plants has to be demonstrated. As soon as these problems have been solved, biomass pyrolysis technologies will offer new attractive bioenergy market opportunities where a huge potential can be reached by conversing existing petroleum-fired boilers, 0.1 - 10 MW to big-oils and followed by combined heat and power production with high-efficiency diesel power plants in 0.1 - 10 MW scale. Pyrolysis technology is clearly the most attractive method for producing liquid biofuels, compared to bioalcohols and biodiesel. With the present price structure, pyrolysis oil can be

  15. Advances in biofuel production from oil palm and palm oil processing wastes: A review

    Directory of Open Access Journals (Sweden)

    Jundika C. Kurnia

    2016-03-01

    Full Text Available Over the last decades, the palm oil industry has been growing rapidly due to increasing demands for food, cosmetic, and hygienic products. Aside from producing palm oil, the industry generates a huge quantity of residues (dry and wet which can be processed to produce biofuel. Driven by the necessity to find an alternative and renewable energy/fuel resources, numerous technologies have been developed and more are being developed to process oil-palm and palm-oil wastes into biofuel. To further develop these technologies, it is essential to understand the current stage of the industry and technology developments. The objective of this paper is to provide an overview of the palm oil industry, review technologies available to process oil palm and palm oil residues into biofuel, and to summarise the challenges that should be overcome for further development. The paper also discusses the research and development needs, technoeconomics, and life cycle analysis of biofuel production from oil-palm and palm-oil wastes.

  16. Optimum oil production planning using infeasibility driven evolutionary algorithm.

    Science.gov (United States)

    Singh, Hemant Kumar; Ray, Tapabrata; Sarker, Ruhul

    2013-01-01

    In this paper, we discuss a practical oil production planning optimization problem. For oil wells with insufficient reservoir pressure, gas is usually injected to artificially lift oil, a practice commonly referred to as enhanced oil recovery (EOR). The total gas that can be used for oil extraction is constrained by daily availability limits. The oil extracted from each well is known to be a nonlinear function of the gas injected into the well and varies between wells. The problem is to identify the optimal amount of gas that needs to be injected into each well to maximize the amount of oil extracted subject to the constraint on the total daily gas availability. The problem has long been of practical interest to all major oil exploration companies as it has the potential to derive large financial benefit. In this paper, an infeasibility driven evolutionary algorithm is used to solve a 56 well reservoir problem which demonstrates its efficiency in solving constrained optimization problems. Furthermore, a multi-objective formulation of the problem is posed and solved using a number of algorithms, which eliminates the need for solving the (single objective) problem on a regular basis. Lastly, a modified single objective formulation of the problem is also proposed, which aims to maximize the profit instead of the quantity of oil. It is shown that even with a lesser amount of oil extracted, more economic benefits can be achieved through the modified formulation.

  17. Simultaneous methane production and wastewater reuse by a membrane-based process: Evaluation with raw domestic wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Gao Dawen, E-mail: dawengao@gmail.com [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China); College of Forestry, Northeast Forestry University, Harbin 150040 (China); An Rui; Tao Yu [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China); Li Jin [Department of Civil Engineering and Mechanics, University of Wisconsin, Milwaukee, Milwaukee, WI 53201 (United States); Li Xinxin; Ren Nanqi [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China)

    2011-02-15

    In this study, a membrane-based process was applied to simultaneously reclaim methane and generate reused water from raw domestic wastewater. The system was comprised of up-flow anaerobic sludge fixed bed (UAFB), anoxic sink (AS) and aerobic membrane bioreactor (MBR). The hydraulic retention time of UAFB (HRT{sub U}) was gradually shortened from 8 h to 6 h, 3 h and to 1 h, while the HRT of AS and MBR kept at 8 h. It is found that HRT{sub U} of 3 h was more suitable for the balancing production of biogas and volatile fatty acids (VFAs), and the VFAs served as carbon source for denitrification. The trans-membrane pressure (TMP) of the MBR kept lower than 0.04 MPa without wash or change of membrane sheet, however, the scanning electron microscopy (SEM) analysis indicated that microbes attached to the inner-surface of membrane, causing irreversible fouling after 133-day operation. The denaturing gradient gel electrophoresis (DGGE) profiles of amplified 16S rDNA gene fragments proved that more functional bacteria and higher microbial diversity emerged at HRT{sub U} of 3 h and 1 h. Most bacteria belonged to Betaproteobacteria and were responsible for carbon and nitrogen removal.

  18. Simultaneous methane production and wastewater reuse by a membrane-based process: Evaluation with raw domestic wastewater

    International Nuclear Information System (INIS)

    Gao Dawen; An Rui; Tao Yu; Li Jin; Li Xinxin; Ren Nanqi

    2011-01-01

    In this study, a membrane-based process was applied to simultaneously reclaim methane and generate reused water from raw domestic wastewater. The system was comprised of up-flow anaerobic sludge fixed bed (UAFB), anoxic sink (AS) and aerobic membrane bioreactor (MBR). The hydraulic retention time of UAFB (HRT U ) was gradually shortened from 8 h to 6 h, 3 h and to 1 h, while the HRT of AS and MBR kept at 8 h. It is found that HRT U of 3 h was more suitable for the balancing production of biogas and volatile fatty acids (VFAs), and the VFAs served as carbon source for denitrification. The trans-membrane pressure (TMP) of the MBR kept lower than 0.04 MPa without wash or change of membrane sheet, however, the scanning electron microscopy (SEM) analysis indicated that microbes attached to the inner-surface of membrane, causing irreversible fouling after 133-day operation. The denaturing gradient gel electrophoresis (DGGE) profiles of amplified 16S rDNA gene fragments proved that more functional bacteria and higher microbial diversity emerged at HRT U of 3 h and 1 h. Most bacteria belonged to Betaproteobacteria and were responsible for carbon and nitrogen removal.

  19. Crude oil derived petroleum products in the aquatic environment: priorities for control

    International Nuclear Information System (INIS)

    Grimwood, M.J.

    2001-01-01

    The available data on the environmental fate, behaviour and toxicity of five groups of petroleum products is reviewed and the information used to identify the priority of oil products for pollution control to protect the aquatic environment. The oil product groups comprise gasolines, kerosenes, other light fuel oil distillates, residual heavy fuel oils and lubricating oils. (author)

  20. Application of Neuro-Fuzzy to palm oil production process | Odior ...

    African Journals Online (AJOL)

    Palm oil is an important nutritional food requirement and in order to facilitate the production of palm oil for consumption, the production process of palm oil has been investigated. The basic operations involved in the production of edible palm oil include; purchase, transportation and reception of oil palm bunches; bunch ...

  1. Extraction solvent’s effect on biogas production from mixtures of date seed and wastewater sludge

    Directory of Open Access Journals (Sweden)

    Radeef Wameed

    2017-01-01

    Full Text Available The objective of this study was to evaluate the impact of extraction solvent on biogas production from mixtures of date (Phoenix dactylifera seed and wastewater treatment sludge. Date palm seed is a locally produced waste which is used in different useful purposes. Date seed is rich in proteins, carbohydrates and lipids and have the potential for biogas enhancement. In this study, three extraction solvents, hexane, ethyl acetate and Ethanol:water (1:1, were used on two types of date seeds (locally known as Khalas and Khudari. Date seed powder of size 0.425 – 0.6 mm after extraction was mixed with wastewater treatment sludge at dry date seed/dry sludge solids ratios of 0%, 10%, 20%, 40%, 60%, and 80%. The study showed a direct relationship between biogas production and ratio of date seeds/wastewater sludge in the mixture. Furthermore, the results confirmed that the quantity of biogas produced from samples containing raw date seed was almost same as the quantity produced from samples containing date seed after extraction. The results revealed that the used extraction solvents had no effect on biogas production

  2. Characterization of the resistome in manure, soil and wastewater from dairy and beef production systems.

    Science.gov (United States)

    Noyes, Noelle R; Yang, Xiang; Linke, Lyndsey M; Magnuson, Roberta J; Cook, Shaun R; Zaheer, Rahat; Yang, Hua; Woerner, Dale R; Geornaras, Ifigenia; McArt, Jessica A; Gow, Sheryl P; Ruiz, Jaime; Jones, Kenneth L; Boucher, Christina A; McAllister, Tim A; Belk, Keith E; Morley, Paul S

    2016-04-20

    It has been proposed that livestock production effluents such as wastewater, airborne dust and manure increase the density of antimicrobial resistant bacteria and genes in the environment. The public health risk posed by this proposed outcome has been difficult to quantify using traditional microbiological approaches. We utilized shotgun metagenomics to provide a first description of the resistome of North American dairy and beef production effluents, and identify factors that significantly impact this resistome. We identified 34 mechanisms of antimicrobial drug resistance within 34 soil, manure and wastewater samples from feedlot, ranch and dairy operations. The majority of resistance-associated sequences found in all samples belonged to tetracycline resistance mechanisms. We found that the ranch samples contained significantly fewer resistance mechanisms than dairy and feedlot samples, and that the resistome of dairy operations differed significantly from that of feedlots. The resistome in soil, manure and wastewater differed, suggesting that management of these effluents should be tailored appropriately. By providing a baseline of the cattle production waste resistome, this study represents a solid foundation for future efforts to characterize and quantify the public health risk posed by livestock effluents.

  3. Studies on bio-hydrogen production of different biomass fermentation types using molasses wastewater as substrate

    Energy Technology Data Exchange (ETDEWEB)

    Liu, K.; Jiao, A.Y.; Rao, P.H. [Northeast Forestry Univ., Harbin (China). School of Forestry; Li, Y.F. [Northeast Forestry Univ., Harbin (China). School of Forestry; Shanghai Univ. Engineering, Shanghai (China). College of Chemistry and Chemical Engineering; Li, W. [Beijing Normal Univ., Beijing (China)

    2010-07-01

    Anaerobic fermentation technology was used to treat molasses wastewater. This study compared the hydrogen production capability of different fermentation types involving dark fermentation hydrogen production. The paper discussed the experiment including the results. It was found that the fermentation type changed by changing engineered control parameters in a continuous stirred tank reactor (CSTR). It was concluded that ethanol-type fermentation resulted in the largest hydrogen production capability, while butyric acid-type fermentation took second place followed by propionic acid-type fermentation.

  4. Contents and risks of potentially toxic elements in wastewater-fed food production systems in Southeast Asia

    DEFF Research Database (Denmark)

    Marcussen, Helle

    , fish, soil and sediment from wastewater-fed production systems in Hanoi and Phnom Penh. Another aim was to assess the food safety risks of water spinach and fish with respect to PTEs. The third aim was to assess PTE retention capacity of river sediment in Hanoi and the governing retention mechanisms...... the concentration range observed for water spinach grown at agricultural soil not exposed to wastewater in Malaysia. Water spinach grown at sites of high and low wastewater exposure did not show a significantly higher accumulation of PTEs compared to sites without wastewater exposure. In Phnom Penh, water spinach...... than 11% of the tolerable intake for each element. The PTE content of water spinach in Hanoi and Cheung Ek Lake in Phnom Penh constituted low food safety risks for consumers. Arsenic, Cd and Pb concentrations in muscle, skin and liver of fish grown in wastewater-fed systems in Hanoi and Phnom were low...

  5. Oil and Gas Production, Environmental Health and Livelihood ...

    African Journals Online (AJOL)

    Oil and Gas Production, Environmental Health and Livelihood Vulnerability in the West Coast of Ghana. ... African Journal of Sustainable Development ... Respondents' level of education significantly influences their level of knowledge about ...

  6. Deposition of naturally occurring radioactivity in oil and gas production

    International Nuclear Information System (INIS)

    Lysebo, I.; Strand, T.

    1997-01-01

    This booklet contains general information about naturally occurring radioactive materials, NORM, in production of oil and natural gas, occupational doses, radiation protection procedures and measures, and classification methods of contaminated equipment. 6 refs., 1 fig., 1 tab

  7. Production of Biodiesel from Parinari polyandra B. Seed Oil using ...

    African Journals Online (AJOL)

    Akorede

    catalysts for the transesterification of Parinari polyandra seeds oil and the results .... reduction in free fatty acids. .... Development and Characterization of Biodiesel from Shea Nut ... comparative review of biodiesel production from Jatropha.

  8. Heavy and Thermal Oil Recovery Production Mechanisms, SUPRI TR-127

    Energy Technology Data Exchange (ETDEWEB)

    Kovscek, Anthony R.; Brigham, William E.; Castanier, Louis M.

    2001-09-07

    The program spans a spectrum of topics and is divided into five categories: (i) multiphase flow and rock properties, (ii) hot fluid injection, (iii) primary heavy-oil production, (iv) reservoir definition, and (v) in-situ combustion.

  9. Lipase-producing fungi for potential wastewater treatment and ...

    African Journals Online (AJOL)

    The use of fungal biomass as a lipase biocatalyst represents an attractive approach for the treatments of oil wastewater as well as for the production of biodiesel from oil and residual grease, due to its greater stability, possibility of reuse, and lower cost. In this work, 20 filamentous fungi were isolated from the grease trap ...

  10. Determining the thermal and physicals properties of oil processing products

    Directory of Open Access Journals (Sweden)

    Viktoria I. Kryvda

    2015-03-01

    Full Text Available In the last decades both technological process’ improvement and primary energy resources saving are the main tasks of oil refineries. Using various oil products does impose an accurate knowledge of their properties. The dispersion analysis applied makes possible to construct a model simulating the primary oil refining products’ and raw materials’ thermal physical properties. As a result of data approximation there were obtained polynomials with coefficients differing from attributable to the studied oil products fractions. The research represents graphic dependences of thermal physical properties on temperature values for diesel oil fraction. The linear character of density and calorific capacity dependencies from temperature is represented with a proportional error in calculations. The relative minimum error is below 2% that confirms the implemented calculations’ adequacy. The resulting model can be used in calculations for further technological process improvements.

  11. Characterization of Salmonella spp. from wastewater used for food production in Morogoro, Tanzania

    DEFF Research Database (Denmark)

    Mhongole, Ofred J.; Mdegela, Robinson H.; Lughano J. M. Kusiluk

    2017-01-01

    Wastewater use for crop irrigation and aquaculture is commonly practiced by communities situated close to wastewater treatment ponds. The objective of this study was to characterize Salmonella spp. and their antimicrobial susceptibility patterns among isolates from wastewater and Tilapia fish...

  12. Characteristics of bicyclic sesquiterpanes in crude oils and petroleum products.

    Science.gov (United States)

    Yang, Chun; Wang, Zhendi; Hollebone, Bruce P; Brown, Carl E; Landriault, Mike

    2009-05-15

    This study presents a quantitative gas chromatography-mass spectrometry analysis of bicyclic sesquiterpanes (BSs) in numerous crude oils and refined petroleum products including light and mid-range distillate fuels, residual fuels, and lubricating oils collected from various sources. Ten commonly recognized bicyclic sesquiterpanes were determined in all the studied crude oils and diesel range fuels with principal dominance of BS3 (C(15)H(28)), BS5 (C(15)H(28)) and BS10 (C(16)H(30)), while they were generally not detected or in trace in light fuel oils like gasoline and kerosene and most lubricating oils. Laboratory distillation of crude oils demonstrated that sesquiterpanes were highly enriched in the medium distillation fractions of approximately 180 to 481 degrees C and were generally absent or very low in the light distillation fraction (boiling point to approximately 180 degrees C) and the heavy residual fraction (>481 degrees C). The effect of evaporative weathering on a series of diagnostic ratios of sesquiterpanes, n-alkanes, and biomarkers was evaluated with two suites of weathered oil samples. The change of abundance of sesquiterpanes was used to determine the extent of weathering of artificially evaporated crude oils and diesel. In addition to the pentacyclic biomarker C(29) and C(30) alphabeta-hopane, C(15) and C(16) sesquiterpanes might be alternative internal marker compounds to provide a direct way to estimate the depletion of oils, particularly diesels, in oil spill investigations. These findings may offer potential applications for both oil identification and oil-source correlation in cases where the tri- to pentacyclic biomarkers are absent due to refining or environmental weathering of oils.

  13. Displacement of oil by gas in power production

    International Nuclear Information System (INIS)

    Sundram, S.; Seng, L.K.; Kow, P.T.A.

    1992-01-01

    After the oil crises, Malaysia unveiled its four fuel diversification policy in the late 1970s towards utilization of gas, oil, coal and hydro. This was to ensure adequate and continuous energy supply for driving economic development and to cushion itself against impact of possible future fluctuations in oil prices. The primary energy supply in 1978 was predominantly oil based, consisting of 75.5% oil. As a result of this diversification policy, the oil component was reduced to about 51.8% in 1988. Due to its inherent ability to adapt and adjust to different fuels, the power sector played a crucial role in this massive shift away from oil. For the corresponding period, the oil component in the electricity generation input mix has decreased from 86.7% oil to 47.4%. Malaysia is endowed with substantial natural gas reserves amounting to 52.5 trillion cubic feet. Gas, therefore constitutes a natural and attractive option for the power sector in diversifying into non-oil indigenous energy resources, as the country's hydro potential has its limitations and the available proven coal reserves are relatively small. The paper addresses the past and current status and issues involved in displacing oil by gas for the power sector. These include the economic, technological and pricing aspects of natural gas development and issues pertaining to power system development. Future gas utilization strategies include the conversion of existing oil-fired plants to gas-fired, and the plant-up of gas turbines and the efficient combined cycle plants to meet the load requirements. These strategies are assessed from the viability and security perspective of increased gas utilization. Oil will continue to be displaced, but the extent to which gas will increase its share in power production is dependent on numerous factors ranging from its economics to supply security

  14. Nigeria's oil production and the need for increased producing capacity

    International Nuclear Information System (INIS)

    Okoroji, C. E. I.

    1998-01-01

    After 40 years of commercial oil production, Nigeria's crude oil production is moving through difficult times. This transition period has been made more difficult because of recurring international economic recession, lack-luster crude prices, and slow oil demand growth and Government funding problems etc. Crude oil remains the most important export revenue earner in Nigeria, and more efforts are required to encourage higher output levels to support more foreign exchange generation. Nigeria's crude oil production at present stands at 2.2 million barrels per day (mbpd). This study, covers the period 1998-2005, during which oil production is forecast to grow to about 2.85 mbpd while potential for new discoveries could raise production to more than 3.0 mbpd. These projected rates could depend to a large extent on the rate and size of new discoveries. However, Nigeria's crude oil potential is being constrained by both lack of infrastructure and inadequate investment. The massive investment needed to raise the country's productive capacity will require foreign capital, yet the current fiscal environment leaves much to be desired. The purpose of this paper is to present a review of Nigeria's past, present and future oil production. To meet the projected production capacity very early in the next millennium, current estimates put the overall potential investment needed for an accelerated capacity-expansion drive in order to ensure that there is adequate cushion of crude potential at $19.7 billion during the next seven years. Furthermore, not more than $12.0 billion of this requirement can be generated from Nigeria's government cash flow

  15. Cultivation of Chlorella vulgaris JSC-6 with swine wastewater for simultaneous nutrient/COD removal and carbohydrate production.

    Science.gov (United States)

    Wang, Yue; Guo, Wanqian; Yen, Hong-Wei; Ho, Shih-Hsin; Lo, Yung-Chung; Cheng, Chieh-Lun; Ren, Nanqi; Chang, Jo-Shu

    2015-12-01

    Swine wastewater, containing a high concentration of COD and ammonia nitrogen, is suitable for the growth of microalgae, leading to simultaneous COD/nutrients removal from the wastewater. In this study, an isolated carbohydrate-rich microalga Chlorella vulgaris JSC-6 was adopted to perform swine wastewater treatment. Nearly 60-70% COD removal and 40-90% NH3-N removal was achieved in the mixotrophic and heterotrophic culture, depending on the dilution ratio of the wastewater, while the highest removal percentage was obtained with 20-fold diluted wastewater. Mixotrophic cultivation by using fivefold diluted wastewater resulted in the highest biomass concentration of 3.96 g/L. The carbohydrate content of the microalga grown on the wastewater can reach up to 58% (per dry weight). The results indicated that the microalgae-based wastewater treatment can efficiently reduce the nutrients and COD level, and the resulting microalgal biomass had high carbohydrate content, thereby having potential applications for the fermentative production of biofuels or chemicals. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. Enzymatic interesterification of vegetable oil/ fish oil blend for margarine production

    DEFF Research Database (Denmark)

    Ibrahim, Nuzul Amri Bin; Xu, Xuebing

    the desired properties. In this study, palm stearin (PS), palm kernel oil (PKO) and fish oil (FO) are blended and modified by enzymatic interesterification. PS functioned as the hard stock, PKO as the soft oil and FO as a source for eicosapentaenoic acid (EPA)/ docosahexaenoic acid (DHA). The purpose...... cause the product to be susceptible to oxidation due to the presence of high content of polyunsaturated fatty acids. Furthermore, FO could also influence the melting properties of the product. Therefore, in addition to determining the fatty acid position on the glycerol backbone, it is also pertinent...

  17. Oil Reservoir Production Optimization using Optimal Control

    DEFF Research Database (Denmark)

    Völcker, Carsten; Jørgensen, John Bagterp; Stenby, Erling Halfdan

    2011-01-01

    Practical oil reservoir management involves solution of large-scale constrained optimal control problems. In this paper we present a numerical method for solution of large-scale constrained optimal control problems. The method is a single-shooting method that computes the gradients using the adjo...... reservoir using water ooding and smart well technology. Compared to the uncontrolled case, the optimal operation increases the Net Present Value of the oil field by 10%.......Practical oil reservoir management involves solution of large-scale constrained optimal control problems. In this paper we present a numerical method for solution of large-scale constrained optimal control problems. The method is a single-shooting method that computes the gradients using...

  18. Fungi-based treatment of brewery wastewater-biomass production and nutrient reduction.

    Science.gov (United States)

    Hultberg, M; Bodin, H

    2017-06-01

    The beer-brewing process produces high amounts of nutrient-rich wastewater, and the increasing number of microbreweries worldwide has created a need for innovative solutions to deal with this waste. In the present study, fungal biomass production and the removal of organic carbon, phosphorus and nitrogen from synthetic brewery wastewater were studied. Different filamentous fungi with a record of safe use were screened for growth, and Trametes versicolor, Pleurotus ostreatus and Trichoderma harzianum were selected for further work. The highest biomass production, 1.78 ± 0.31 g L -1 of dry weight, was observed when P. ostreatus was used for the treatment, while T. harzianum demonstrated the best capability for removing nutrients. The maximum reduction of chemical oxygen demand, 89% of the initial value, was observed with this species. In the removal of total nitrogen and phosphorus, no significant difference was observed between the species, while removal of ammonium varied between the strains. The maximum reduction of ammonium, 66.1% of the initial value, was also found in the T. harzianum treatment. It can be concluded that all treatments provided significant reductions in all water-quality parameters after 3 days of growth and that the utilisation of filamentous fungi to treat brewery wastewater, linked to a deliberate strategy to use the biomass produced, has future potential in a bio-based society.

  19. Rice production with minimal irrigation and no nitrogen fertilizer by intensive use of treated municipal wastewater.

    Science.gov (United States)

    Muramatsu, Ayumi; Watanabe, Toru; Sasaki, Atsushi; Ito, Hiroaki; Kajihara, Akihiko

    2014-01-01

    We designed a new cultivation system of rice with circulated irrigation to remove nitrogen from treated municipal wastewater effectively and assessed the possibility of nitrogen removal in the new system without any adverse effects on rice production through bench-scale experiments through two seasons. Overgrowth of the rice plant, which can lead to lodging and tasteless rice, was found in the first season probably because nitrogen supply based on standard practice in normal paddy fields was too much in the closed irrigation system. In the second season, therefore, the amount of treated wastewater initially applied to the system was reduced but this resulted in a considerably decreased yield. On the other hand, the taste of the rice was significantly improved. The two-season experiments revealed that the new system enabled rice production with minimal irrigation (approximately 50% on the yield base compared to normal paddy fields) and no nitrogen fertilizer. The system also achieved >95% removal of nitrogen from the treated wastewater used for circulated irrigation. The accumulation of harmful metals in the rice was not observed after one season of cultivation in the new system. The accumulation after cultivation using the same soil repeatedly for a longer time should be examined by further studies.

  20. Wastewater treatment and biodiesel production by Scenedesmus obliquus in a two-stage cultivation process.

    Science.gov (United States)

    Álvarez-Díaz, P D; Ruiz, J; Arbib, Z; Barragán, J; Garrido-Pérez, M C; Perales, J A

    2015-04-01

    The microalga Scenedesmus obliquus was cultured in two cultivation stages: (1) in batch with real wastewater; (2) maintaining the stationary phase with different conditions of CO2, light and salinity according to a factorial design in order to improve the lipid content. The presence of the three factors increased lipid content from 35.8% to 49% at the end of the second stage; CO2 presence presented the highest direct effect increasing lipid content followed by light presence and salt presence. The ω-3 fatty acids content increased with CO2 and light presence acting in isolation, nevertheless, when both factors acted together the interaction effect was negative. The ω-3 eicosapentaenoic acid content of the oil from S. obliquus slightly exceeded the 1% maximum to be used as biodiesel source (EU normative). Therefore, it is suggested the blend with other oils or the selective extraction of the ω-3 fatty acids from S. obliquus oil. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. The Study of the Desulfurization Process of Oil and Oil Products of "Zhanazhol" Oil Field Using the Approaches of Green Chemistry

    OpenAIRE

    Zhaksyntay K. Kairbekov; Zhannur K. Myltykbaeva; Nazym T. Smagulova; Dariya K. Kanseitova

    2015-01-01

    In this paper we studied sono catalytic oxidative desulfurization of oil and diesel fraction from “Zhanazhol” oil deposits. We have established that the combined effect of the ultrasonic field and oxidant (ozone-air mixture) in the presence of the catalyst on the oil is potentially very effective method of desulfurization of oil and oil products. This method allows increasing the degree of desulfurization of oil by 62%.

  2. Biosurfactants production and possible uses in microbial enhanced oil recovery and oil pollution remediation: a review

    International Nuclear Information System (INIS)

    Banat, I.M.

    1995-01-01

    Surfactants are widely used for various purposes in industry, but for many years were mainly chemically synthesized. It has only been in the past few decades that biological surface-active compounds (biosurfactants) have been described. Biosurfactants are gaining prominence and have already taken over for a number of important industrial uses, due to their advantages of biodegradability, production on renewable resources and functionality under extreme conditions; particularly those pertaining during tertiary crude-oil recovery. Conflicting reports exist concerning their efficacy and the economics of both their production and application. The limited successes and applications for biosurfactants production, recovery, use in oil pollution control, oil storage tank clean-up and enhanced oil-recovery are reviewed from the technical point of view. (author)

  3. Prevention of volatile fatty acids production and limitation of odours from winery wastewaters by denitrification.

    Science.gov (United States)

    Bories, André; Guillot, Jean-Michel; Sire, Yannick; Couderc, Marie; Lemaire, Sophie-Andréa; Kreim, Virginie; Roux, Jean-Claude

    2007-07-01

    The effect of the addition of nitrate to winery wastewaters to control the formation of VFA in order to prevent odours during storage and treatment was studied in batch bioreactors at different NO(3)/chemical oxygen demand (COD) ratios and at full scale in natural evaporation ponds (2 x 7000 m(2)) by measuring olfactory intensity. In the absence of nitrate, butyric acid (2304 mgL(-1)), acetic acid (1633 mgL(-1)), propionic acid (1558 mgL(-1)), caproic acid (499 mgL(-1)) and valeric acid (298 mgL(-1)) were produced from reconstituted winery wastewater. For a ratio of NO(3)/COD=0.4 gg(-1), caproic and valeric acids were not formed. The production of butyric and propionic acids was reduced by 93.3% and 72.5%, respectively, at a ratio of NO(3)/COD=0.8, and by 97.4% and 100% at a ratio of NO(3)/COD=1.2 gg(-1). Nitrate delayed and decreased butyric acid formation in relation to the oxidoreduction potential. Studies in ponds showed that the addition of concentrated calcium nitrate (NITCAL) to winery wastewaters (3526 m(3)) in a ratio of NO(3)/COD=0.8 inhibited VFA production, with COD elimination (94%) and total nitrate degradation, and no final nitrite accumulation. On the contrary, in ponds not treated with nitrate, malodorous VFA (from propionic to heptanoïc acids) represented up to 60% of the COD. Olfactory intensity measurements in relation to the butanol scale of VFA solutions and the ponds revealed the pervasive role of VFA in the odour of the untreated pond as well as the clear decrease in the intensity and not unpleasant odour of the winery wastewater pond enriched in nitrates. The results obtained at full scale underscored the feasibility and safety of the calcium nitrate treatment as opposed to concentrated nitric acid.

  4. Rhagoletis cerasi: Oviposition Reduction Effects of Oil Products

    Directory of Open Access Journals (Sweden)

    Claudia Daniel

    2014-04-01

    Full Text Available The European cherry fruit fly, Rhagoletis cerasi (L. (Diptera: Tephritidae, is a highly destructive pest. Methods to control it are limited and alternatives are needed. Observations of cherry fruit flies suggest that females exert much effort to penetrate cherries at color change stage (from green to yellow for oviposition. Therefore, the question arose as to whether a physical barrier on the fruit surface could reduce oviposition. The effects of different commercial horticultural oil products on R. cerasi oviposition were evaluated in a series of laboratory, semi-field and field experiments. In the laboratory experiments, the rate of successful oviposition on fruits treated with 0.25% v/v of the rapeseed oil product Telmion was significantly reduced by 90% compared to the untreated control. In semi-field experiments, deposits of 1% of rapeseed, mineral and paraffinic oil significantly reduced oviposition for up to 3 days. Semi-field experiments indicated that the oil products lose efficacy within 3 to 6 days after application due to degradation. Although treatments with the rapeseed oil product Telmion reduced infestation rates in an on-farm field experiment, the infested fruit clearly exceeded the level of market tolerance of 2%. Further research is needed to assess whether combinations of oil products, higher application rates and different formulations might improve field efficacy.

  5. Quality of feedstock in production of lubricating oils

    Energy Technology Data Exchange (ETDEWEB)

    Martynenko, A.G.; Kalenik, G.S.; Bayburskaya, E.L.; Ledyashova, G.Ye.; Okhrimenko, N.V.; Potashnikov, G.L.; Shiryayeva, G.P.

    1980-01-01

    Data are obtained under industrial conditions concerning production of lubricating oils from the mixture of crudes distinguished in terms of major properties: viscosity, content of light petroleum products, resin, sulfur. The difference in main properties and hydrocarbon composition of the original feedstock caused a change in conditions of selective purification of output of target and intermediate products. It is demonstrated that selection and grading of Eastern Ukrainian petroleum (separation of gas condensate) can achieve a continued increase of production of oils, approximately 30 percent.

  6. Production of fungal biomass protein using microfungi from winery wastewater treatment.

    Science.gov (United States)

    Zhang, Zhan Ying; Jin, Bo; Bai, Zhi Hui; Wang, Xiao Yi

    2008-06-01

    This study was carried out to investigate the production of fungal biomass protein (FBP) in treatment of winery wastewater using microfungi. Three fungal strains, Trichoderma viride WEBL0702, Aspergillus niger WEBL0901 and Aspergillus oryzae WEBL0401, were selected in terms of microbial capability for FBP production and COD reduction. T. viride appeared to be the best strain for FBP production due to high productivity and less nitrogen requirement. More than 5 g/L of fungal biomass was produced in shake fermentation using T. viride without nitrogen addition, and by A. oryzae and A. niger with addition of 0.5-1.0 g/L (NH4)2SO4. The FBP production process corresponded to 84-90% COD reduction of winery wastewater. Fungal biomass contained approximately 36% protein produced by two Aspergillus strains, while biomass produced by T. viride consisted of 19.8% protein. Kinetic study indicated that maximum fungal cell growth could be achieved in 24h for T. viride and 48 h for A. oryzae and A. niger. Current results indicated that it could be feasible to develop a biotechnological treatment process integrated with FBP production from the winery waste streams.

  7. Borehole radar for oil production monitoring

    NARCIS (Netherlands)

    Miorali, M.

    2012-01-01

    The area of smart well technology, or closed-loop reservoir management, aims at enhancing oil recovery through a combination of monitoring and control. Monitoring is performed with a wide range of sensors deployed downhole or at the surface. These sensors allow for capturing changes in the reservoir

  8. Shifting production trends point to more oil from OPEC

    International Nuclear Information System (INIS)

    Ismail, I.A.H.

    1994-01-01

    Oil production from the Organization of Petroleum Exporting Countries and non-OPEC regions has undergone four major phases of change in relation to oil price since 1960. Patterns visible in those phases offer an indication of world-wide production trends in the future. These four phases are described. Overall, demand for oil during 1960--93 has increased from around 20 million b/d in 1960 to as high as 65 million b/d in 1993. The consensus among energy analysts and forecasters is that this demand growth will continue. This will encourage OPEC and non OPEC producers to invest in the oil industry to meet future demand growth. However, since the resource base is larger in OPEC than in non-OPEC areas, and since the cost of developing these resources is lower in OPEC than outside OPEC, the future call on OPEC oil to meet growth in demand will undoubtedly be substantiated as production from the non-OPEC region diminishes or at best stagnates. The paper discusses OPEC production trends, non-OPEC production, natural gas liquids, future production scenarios, and future constraints on production

  9. OPEC oil production and market fundamentals: a causality relationship

    International Nuclear Information System (INIS)

    Dahmani, A.; Al-Osaimy, M.H.

    2001-01-01

    This paper first establishes a statistical measurement for OPEC Member Countries' compliance levels with their respective quotas and then examines the correlations and the casual relationships between compliance levels and oil market fundamentals. The compliance level is measured by the deviation of the production level from the respective quota for OPEC Member Countries, and this is based on the Euclidean distance formula, while oil market fundamentals are represented by OECD oil demand and stock levels, and the OPEC Basket price and oil supply. Monthly data from January 1996 to June 2000 was used and two sub-periods considered, where the first sub-period was characterized by a low level of compliance and the second by a high level. The analytical results of correlations and causality showed different directions of relationships between compliance levels and oil market fundamentals. (author)

  10. Avocado oil extraction processes: method for cold-pressed high-quality edible oil production versus traditional production

    Directory of Open Access Journals (Sweden)

    Giacomo Costagli

    2015-10-01

    Full Text Available Nowadays the avocado fruit (Persea americana Mill. is widely regarded as an important fruit for its nutritional values, as it is rich in vital human nutrients. The avocado fruit is mainly sold fresh on the market, which however trades also a relevant quantity of second-grade fruits with a relatively high oil content. Traditionally, this oil is extracted from dried fruits by means of organic solvents, but a mechanical method is also used in general in locations where drying systems and/or solvent extraction units cannot be installed. These traditional processes yield a grade of oil that needs subsequent refining and is mainly used in the cosmetic industry. In the late 1990s, in New Zeland, a processing company with the collaboration of Alfa Laval began producing cold-pressed avocado oil (CPAO to be sold as edible oil for salads and cooking. Over the last fifteen years, CPAO production has increased in many other countries and has led to an expansion of the market which is set to continue, given the growing interest in highquality and healthy food. Avocado oil like olive oil is extracted from the fruit pulp and in particular shares many principles of the extraction process with extra-vergin olive oil. We conducted a review of traditional and modern extraction methods with particular focus on extraction processes and technology for CPAO production.

  11. Life cycle assessment of two palm oil production systems

    International Nuclear Information System (INIS)

    Stichnothe, Heinz; Schuchardt, Frank

    2011-01-01

    In 2009 approx. 40 Mt of palm oil were produced globally. Growing demand for palm oil is driven by an increasing human population as well as subsidies for biodiesel and is likely to increase further in coming years. The production of 1 t crude palm oil requires 5 t of fresh fruit bunches (FFB). On average processing of 1 t FFB in palm oil mills generates 0.23 t empty fruit bunches (EFB) and 0.65 t palm oil mill effluents (POME) as residues. In this study it is assumed that land use change does not occur. In order to estimate the environmental impacts of palm oil production a worst and a best case scenario are assessed and compared in the present study using 1000 kg of FFB as functional unit. The production and treatment of one t FFB causes more than 460 kg CO 2eq in the worst case scenario and 110 kg CO 2eq in the best case scenario. The significant greenhouse gas (GHG) emission reduction is achieved by co-composting residues of the palm oil mill. Thus treating those residues appropriately is paramount for reducing environmental impacts particularly global warming potential (GWP) and eutrophication potential (EP). Another important contributor to the EP but also to the human toxicity potential (HTP) is the biomass powered combined heat and power (CHP) plant of palm oil mills. Frequently CHP plants of palm oil mills operate without flue gas cleaning. The CHP plant emits heavy metals and nitrogen oxides and these account for 93% of the HTP of the advanced palm oil production system, of which heavy metal emissions to air are responsible for 79%. The exact emission reduction potential from CHP plants could not be quantified due to existing data gaps, but it is apparent that cleaning the exhaust gas would reduce eutrophication, acidification and toxicity considerably. -- Highlights: → We have estimated the environmental impacts of two palm oil production systems. → Residues from palm oil mills are a wasted resource rather than waste. → Co-composting of EFB and

  12. Cultivating Microalgae in Domestic Wastewater for Biodiesel Production

    Directory of Open Access Journals (Sweden)

    Soha S.M. MOSTAFA

    2012-02-01

    Full Text Available The objective of this study was to evaluate the growth of nine species of microalgae (green and blue green microalgae on domestic waste water samples obtained from Zenein Waste Water Treatment Plant (ZWWTP, Giza governorate, Egypt. The species were cultivated in different kind of waste water; before treatment; after sterilization; with nutrients with sterilization and with nutrients without sterilization. The experiment was conducted in triplicate and cultures were incubated at 25�1�C under continuous shaking (150 rpm and illumination (2000 Lux for 15 days. pH, electric conductivity (EC, optical density (OD , dry weight (DW, were done at the time of incubation and at the end of experiment, in addition to determine the percentage of lipid and biodiesel. The data revealed that, domestic waste water with nutrient media (T3 was promising for cultivation of five algal species when compared with conventional media, Moreover, domestic waste water after sterilization (T2 was selected media for cultivation of Oscillatoria sp and Phormedium sp. However, T1 media (waste water without treatment was the promising media for cultivation of Nostoc humifusum. The biodiesel produced from algal species cultivated in waste water media ranged from 3.8 to 11.80% when compared with the conventional method (3.90 to 12.52%. The results of this study suggest that growing algae in nutrient rich media offers a new option of applying algal process in ZWWTP to mange the nutrient load for growth and valuable biodiesel feedstock production.

  13. Cultivating Microalgae in Domestic Wastewater for Biodiesel Production

    Directory of Open Access Journals (Sweden)

    Soha S.M. MOSTAFA

    2012-02-01

    Full Text Available The objective of this study was to evaluate the growth of nine species of microalgae (green and blue green microalgae on domestic waste water samples obtained from Zenein Waste Water Treatment Plant (ZWWTP, Giza governorate, Egypt. The species were cultivated in different kind of waste water; before treatment; after sterilization; with nutrients with sterilization and with nutrients without sterilization. The experiment was conducted in triplicate and cultures were incubated at 251C under continuous shaking (150 rpm and illumination (2000 Lux for 15 days. pH, electric conductivity (EC, optical density (OD , dry weight (DW, were done at the time of incubation and at the end of experiment, in addition to determine the percentage of lipid and biodiesel. The data revealed that, domestic waste water with nutrient media (T3 was promising for cultivation of five algal species when compared with conventional media, Moreover, domestic waste water after sterilization (T2 was selected media for cultivation of Oscillatoria sp and Phormedium sp. However, T1 media (waste water without treatment was the promising media for cultivation of Nostoc humifusum. The biodiesel produced from algal species cultivated in waste water media ranged from 3.8 to 11.80% when compared with the conventional method (3.90 to 12.52%. The results of this study suggest that growing algae in nutrient rich media offers a new option of applying algal process in ZWWTP to mange the nutrient load for growth and valuable biodiesel feedstock production.

  14. Peaking of world oil production: Impacts, mitigation, & risk management

    Energy Technology Data Exchange (ETDEWEB)

    Hirsch, R.L. (SAIC); Bezdek, Roger (MISI); Wendling, Robert (MISI)

    2005-02-01

    The peaking of world oil production presents the U.S. and the world with an unprecedented risk management problem. As peaking is approached, liquid fuel prices and price volatility will increase dramatically, and, without timely mitigation, the economic, social, and political costs will be unprecedented. Viable mitigation options exist on both the supply and demand sides, but to have substantial impact, they must be initiated more than a decade in advance of peaking.... The purpose of this analysis was to identify the critical issues surrounding the occurrence and mitigation of world oil production peaking. We simplified many of the complexities in an effort to provide a transparent analysis. Nevertheless, our study is neither simple nor brief. We recognize that when oil prices escalate dramatically, there will be demand and economic impacts that will alter our simplified assumptions. Consideration of those feedbacks will be a daunting task but one that should be undertaken. Our aim in this study is to-- • Summarize the difficulties of oil production forecasting; • Identify the fundamentals that show why world oil production peaking is such a unique challenge; • Show why mitigation will take a decade or more of intense effort; • Examine the potential economic effects of oil peaking; • Describe what might be accomplished under three example mitigation scenarios. • Stimulate serious discussion of the problem, suggest more definitive studies, and engender interest in timely action to mitigate its impacts.

  15. Production of Biodiesel from Waste Vegetable Oil via KM Micromixer

    Directory of Open Access Journals (Sweden)

    M. F. Elkady

    2015-01-01

    Full Text Available The production of biodiesel from waste vegetable oils through its pretreatment followed by transesterification process in presence of methanol was investigated using a KM micromixer reactor. The parameters affecting biodiesel production process such as alcohol to oil molar ratio, catalyst concentration, the presence of tetrahydrofuran (THF as a cosolvent, and the volumetric flow rates of inlet fluids were optimized. The properties of the produced biodiesel were compared with its parent waste oil through different characterization techniques. The presence of methyl ester groups at the produced biodiesel was confirmed using both the gas chromatography-mass spectrometry (GC-MS and the infrared spectroscopy (FT-IR. Moreover, the thermal analysis of the produced biodiesel and the comparable waste oil indicated that the product after the transesterification process began to vaporize at 120°C which makes it lighter than its parent oil which started to vaporize at around 300°C. The maximum biodiesel production yield of 97% was recorded using 12 : 1 methanol to oil molar ratio in presence of both 1% NaOH and THF/methanol volume ratio 0.3 at 60 mL/h flow rate.

  16. Biomass and pigments production in photosynthetic bacteria wastewater treatment: effects of light sources.

    Science.gov (United States)

    Zhou, Qin; Zhang, Panyue; Zhang, Guangming

    2015-03-01

    This study is aimed at enhancing biomass and pigments production together with pollution removal in photosynthetic bacteria (PSB) wastewater treatment via different light sources. Red, yellow, blue, white LED and incandescent lamp were used. Results showed different light sources had great effects on the PSB. PSB had the highest biomass production, COD removal and biomass yield with red LED. The corresponding biomass, COD removal and biomass yield reached 2580 mg/L, 88.6% and 0.49 mg-biomass/mg-COD-removal, respectively. The hydraulic retention time of wastewater treatment could be shortened to 72 h with red LED. Mechanism analysis showed higher ATP was produced with red LED than others. Light sources could significantly affect the pigments production. The pigments productions were greatly higher with LED than incandescent lamp. Yellow LED had the highest pigments production while red LED produced the highest carotenoid/bacteriochlorophyll ratio. Considering both efficiency and energy cost, red LED was the optimal light source. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Pipeline oil fire detection with MODIS active fire products

    Science.gov (United States)

    Ogungbuyi, M. G.; Martinez, P.; Eckardt, F. D.

    2017-12-01

    We investigate 85 129 MODIS satellite active fire events from 2007 to 2015 in the Niger Delta of Nigeria. The region is the oil base for Nigerian economy and the hub of oil exploration where oil facilities (i.e. flowlines, flow stations, trunklines, oil wells and oil fields) are domiciled, and from where crude oil and refined products are transported to different Nigerian locations through a network of pipeline systems. Pipeline and other oil facilities are consistently susceptible to oil leaks due to operational or maintenance error, and by acts of deliberate sabotage of the pipeline equipment which often result in explosions and fire outbreaks. We used ground oil spill reports obtained from the National Oil Spill Detection and Response Agency (NOSDRA) database (see www.oilspillmonitor.ng) to validate MODIS satellite data. NOSDRA database shows an estimate of 10 000 spill events from 2007 - 2015. The spill events were filtered to include largest spills by volume and events occurring only in the Niger Delta (i.e. 386 spills). By projecting both MODIS fire and spill as `input vector' layers with `Points' geometry, and the Nigerian pipeline networks as `from vector' layers with `LineString' geometry in a geographical information system, we extracted the nearest MODIS events (i.e. 2192) closed to the pipelines by 1000m distance in spatial vector analysis. The extraction process that defined the nearest distance to the pipelines is based on the global practices of the Right of Way (ROW) in pipeline management that earmarked 30m strip of land to the pipeline. The KML files of the extracted fires in a Google map validated their source origin to be from oil facilities. Land cover mapping confirmed fire anomalies. The aim of the study is to propose a near-real-time monitoring of spill events along pipeline routes using 250 m spatial resolution of MODIS active fire detection sensor when such spills are accompanied by fire events in the study location.

  18. Bioconversion of wastewater from sweet potato starch production to Paenibacillus polymyxa biofertilizer for tea plants.

    Science.gov (United States)

    Xu, Shengjun; Bai, Zhihui; Jin, Bo; Xiao, Runlin; Zhuang, Guoqiang

    2014-02-28

    Wastewater from the sweet potato starch industry is a large source of nutrient-rich substrates. We assessed whether this wastewater could be used to produce Paenibacillus polymyxa biofertilizer for foliar application to tea trees. Using the central composite design methods we experientially determined that the optimal culture conditions for P. polymyxa were pH, 6.5; temperature, 29.0 °C; and incubation time, 16 h. Under these conditions, a maximum biomass of 9.7 × 10(9) cfu/mL was achieved. We then conducted a yearlong field investigation to determine the effect of P. polymyxa biofertilizer on the growth of tea plants (Camellia sinensis). Tea yield, quantity of water extract, and tea polyphenol levels were significantly higher after foliar application of the biofertilizer compared to that in the controls by an average of 16.7%, 6.3%, and 10.4%, respectively. This approach appears to be technically feasible for organic tea production, and is an environmentally friendly way to utilize wastewater.

  19. Ethanol production potential from fermented rice noodle wastewater treatment using entrapped yeast cell sequencing batch reactor

    Science.gov (United States)

    Siripattanakul-Ratpukdi, Sumana

    2012-03-01

    Fermented rice noodle production generates a large volume of starch-based wastewater. This study investigated the treatment of the fermented rice noodle wastewater using entrapped cell sequencing batch reactor (ECSBR) compared to traditional sequencing batch reactor (SBR). The yeast cells were applied because of their potential to convert reducing sugar in the wastewater to ethanol. In present study, preliminary treatment by acid hydrolysis was performed. A yeast culture, Saccharomyces cerevisiae, with calcium alginate cell entrapment was used. Optimum yeast cell loading in batch experiment and fermented rice noodle treatment performances using ECSBR and SBR systems were examined. In the first part, it was found that the cell loadings (0.6-2.7 × 108 cells/mL) did not play an important role in this study. Treatment reactions followed the second-order kinetics with the treatment efficiencies of 92-95%. In the second part, the result showed that ECSBR performed better than SBR in both treatment efficiency and system stability perspectives. ECSBR maintained glucose removal of 82.5 ± 10% for 5-cycle treatment while glucose removal by SBR declined from 96 to 40% within the 5-cycle treatment. Scanning electron microscopic images supported the treatment results. A number of yeast cells entrapped and attached onto the matrix grew in the entrapment matrix.

  20. A survey of oil product demand elasticities for developing countries

    International Nuclear Information System (INIS)

    Dahl, Carol

    1994-01-01

    As more and more developing countries join the ranks of the rich they will consume both more oil and higher percentage of the lighter products. To satisfy this growing demand oil production and refinery capacity that can provide the right quantity and mix of products must be developed. In a companion piece, Dahl (1993) found the total demand for oil to be price inelastic (-0.34) and income elastic (1.32) These elasticities can give information on the total quantity of oil that might be demanded, the total amount of distillation capacity that might be needed and the overall increases in product prices that might be necessary to choke off demand growth. However, with this overall growth in product demand, the more the shift towards the lighter portion of the barrel, the more complex the refinery and the greater the demand for downstream capital. To provide information on this mix in developing countries in the coming years, this paper surveys the available work on econometric demand elasticities by oil product. (author)

  1. Biotechnological processes for biodiesel production using alternative oils

    Energy Technology Data Exchange (ETDEWEB)

    Azocar, Laura; Ciudad, Gustavo [La Frontera Univ., Temuco (Chile). Nucleo Cietifico Tecnologico en Biorrecursos; Heipieper, Hermann J. [Helmholtz Centre for Environmental Research-UFZ, Leipzig (Germany). Dept. of Environmental Biotechnology; Navia, Rodrigo [La Frontera Univ., Temuco (Chile). Nucleo Cietifico Tecnologico en Biorrecursos; La Frontera Univ., Temuco (Chile). Dept. de Ingenieria Quimica

    2010-10-15

    As biodiesel (fatty acid methyl ester (FAME)) is mainly produced from edible vegetable oils, crop soils are used for its production, increasing deforestation and producing a fuel more expensive than diesel. The use of waste lipids such as waste frying oils, waste fats, and soapstock has been proposed as low-cost alternative feedstocks. Non-edible oils such as jatropha, pongamia, and rubber seed oil are also economically attractive. In addition, microalgae, bacteria, yeast, and fungi with 20% or higher lipid content are oleaginous microorganisms known as single cell oil and have been proposed as feedstocks for FAME production. Alternative feedstocks are characterized by their elevated acid value due to the high level of free fatty acid (FFA) content, causing undesirable saponification reactions when an alkaline catalyst is used in the transesterification reaction. The production of soap consumes the conventional catalyst, diminishing FAME production yield and simultaneously preventing the effective separation of the produced FAME from the glycerin phase. These problems could be solved using biological catalysts, such as lipases or whole-cell catalysts, avoiding soap production as the FFAs are esterified to FAME. In addition, by-product glycerol can be easily recovered, and the purification of FAME is simplified using biological catalysts. (orig.)

  2. Transformation of soil and vegetable conditions at oil production territories

    Science.gov (United States)

    Gatina, Evgeniia

    2017-04-01

    On the territory of modern oil production soil, vegetation, ecosystem conditions of the environment are significantly transformed. Researches have been conducted on the oil production territories located in a boreal coniferous forest natural zone from 2005 to 2015. Standard geobotanical and soil methods are used. Mechanical destruction of a plant cover, change of the water conditions, intake of oil products and salty waters in ecosystems, pollution of the atmosphere are considered as the major technology-related factors defining transformation of land ecosystems at operation of the oil field. Under the mechanical destruction of a plant cover the pioneer plant communities are formed. These communities are characterized by most reduced specific wealth with prevalence of types of meadow groups of plants and presence of types of wetland groups of plants. The biodiversity of biocenosis which are affected linear infrastructure facilities of oil production territories and change of the water conditions, decreases. It is observed decrease in species wealth, simplification of structure of communities. Under the salting of soils in ecosystems there is a decrease species diversity of communities to prevalence nitrophilous and meadow plant species. At the increased content of organic substances in the soils that is a consequence of intake of oil products, is characteristic increase in specific richness of communities, introduction of types of wetland and oligotrophic groups of plants in forest communities. Influence depends on distance to an influence source. In process of removal from a source of atmospheric pollution in forest communities there is a decrease in species diversity and complication of structure of community. It is caused by introduction of types of meadow groups of plants in ecotone sites of the forest communities located near a source of influence and restoration of structural features of forest communities in process of removal from an influence source

  3. Conversion of Crude Oil to Methane by a Microbial Consortium Enriched From Oil Reservoir Production Waters

    Directory of Open Access Journals (Sweden)

    Carolina eBerdugo-Clavijo

    2014-05-01

    Full Text Available The methanogenic biodegradation of crude oil is an important process occurring in petroleum reservoirs and other oil-containing environments such as contaminated aquifers. In this process, syntrophic bacteria degrade hydrocarbon substrates to products such as acetate, and/or H2 and CO2 that are then used by methanogens to produce methane in a thermodynamically dependent manner. We enriched a methanogenic crude oil-degrading consortium from production waters sampled from a low temperature heavy oil reservoir. Alkylsuccinates indicative of fumarate addition to C5 and C6 n-alkanes were identified in the culture (above levels found in controls, corresponding to the detection of an alkyl succinate synthase gene (assA in the culture. In addition, the enrichment culture was tested for its ability to produce methane from residual oil in a sandstone-packed column system simulating a mature field. Methane production rates of up 5.8 μmol CH4/g of oil/day were measured in the column system. Amounts of produced methane were in relatively good agreement with hydrocarbon loss showing depletion of more than 50% of saturate and aromatic hydrocarbons. Microbial community analysis revealed that the enrichment culture was dominated by members of the genus Smithella, Methanosaeta, and Methanoculleus. However, a shift in microbial community occurred following incubation of the enrichment in the sandstone columns. Here, Methanobacterium sp. were most abundant, as were bacterial members of the genus Pseudomonas and other known biofilm forming organisms. Our findings show that microorganisms enriched from petroleum reservoir waters can bioconvert crude oil components to methane both planktonically and in sandstone-packed columns as test systems. Further, the results suggest that different organisms may contribute to oil biodegradation within different phases (e.g., planktonic versus sessile within a subsurface crude oil reservoir.

  4. Air toxics from heavy oil production and consumption

    International Nuclear Information System (INIS)

    Lipfert, F.W.; DePhillips, M.P.; Moskowitz, P.D.

    1992-01-01

    This report assesses the potential impact of recent Federal and state regulations for airborne toxic substances on the production and consumption of heavy fuel oils. Emissions of nickel from heavy oil production in California are considered in some detail, in conjunction with California state regulations for toxic emissions. Although the use of thermal energy from heavy crude oils could in theory be impacted by toxic air pollution regulations, recent trends towards the use of natural gas for the required extraction energy appear to provide substantial relief, in addition to reducing emissions of criteria air pollutants. However, the consumption of residual fuel oils containing toxic metals could result in higher population exposures to these substances and their attendant risks may be worthy of more detailed analysis

  5. Method for creating high carbon content products from biomass oil

    Science.gov (United States)

    Parker, Reginald; Seames, Wayne

    2012-12-18

    In a method for producing high carbon content products from biomass, a biomass oil is added to a cracking reactor vessel. The biomass oil is heated to a temperature ranging from about 100.degree. C. to about 800.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to crack the biomass oil. Tar is separated from the cracked biomass oil. The tar is heated to a temperature ranging from about 200.degree. C. to about 1500.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to reduce the tar to a high carbon content product containing at least about 50% carbon by weight.

  6. Biodiesel Production from Rubber Seed Oil via Esterification Process

    Directory of Open Access Journals (Sweden)

    W Widayat

    2012-07-01

    Full Text Available One promise source of alternative energy is biodiesel from rubber seed oil, because the raw materials available in plentiful quantities and can be renewed. In addition, the rubber seed is still lack of utilization, and Indonesia is one of the largest rubbers producing country in the world. The objective of this research is to studied on biodiesel production by esterification process. Parameters used in this study are the ratio of catalyst and temperature and its influence on the characteristics of the resulting biodiesel product. Characterization of rubber seed include acid content number analysis, saponification numbers, density, viscosity, iodine number, type of free fatty acids and triglyceride oils. The results of analysis showed that rubber seed oil content obtained is 50.5%. The results of the GCMS analysis showed that a free fatty acid level in rubber seed is very high. Conversion into bio-diesel oil is obtained by at most 59.91% and lowest 48.24%.

  7. Use of calcium oxide in palm oil methyl ester production

    Directory of Open Access Journals (Sweden)

    Kulchanat Prasertsit

    2014-04-01

    Full Text Available Introducing an untreated calcium oxide (CaO as a solid heterogeneous catalyst for biodiesel production from palm oil by transesterification was studied in this work. The four studied parameters were methanol to oil molar ratio, CaO catalyst concentration, reaction time, and water content. The results for palm oil show that when the water content is higher than 3%wt and the amount of CaO greater than 7%wt soap formation from saponification occurs. A higher methanol to oil molar ratio requires a higher amount of CaO catalyst to provide the higher product purity. The appropriate methanol to CaO catalyst ratio is about 1.56. Commercial grade CaO gives almost the same results as AR grade CaO. In addition, reusing commercial grade CaO for about 5 to 10 repetitions without catalyst regeneration drops the percentage of methyl ester purity approximately 5 to 10%, respectively.

  8. Opportunities to improve oil productivity in unstructured deltaic reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-01

    This report contains presentations presented at a technical symposium on oil production. Chapter 1 contains summaries of the presentations given at the Department of Energy (DOE)-sponsored symposium and key points of the discussions that followed. Chapter 2 characterizes the light oil resource from fluvial-dominated deltaic reservoirs in the Tertiary Oil Recovery Information System (TORIS). An analysis of enhanced oil recovery (EOR) and advanced secondary recovery (ASR) potential for fluvial-dominated deltaic reservoirs based on recovery performance and economic modeling as well as the potential resource loss due to well abandonments is presented. Chapter 3 provides a summary of the general reservoir characteristics and properties within deltaic deposits. It is not exhaustive treatise, rather it is intended to provide some basic information about geologic, reservoir, and production characteristics of deltaic reservoirs, and the resulting recovery problems.

  9. Production of Biodiesel from Mixed Waste Cooking and Castor Oil

    Directory of Open Access Journals (Sweden)

    Hadiyanto Hadiyanto

    2018-01-01

    Full Text Available Due to increasing population growth, the consumption and needs of energy increase significantly. This leads Indonesia government to search alternative energy to cover the lacks of fossil energy reserves. Biodiesel is one of the prospective alternative energy which are renewable and environmental friendly. A common problem in large-scale biodiesel production is the sustainability of feedstock and the biodiesel stability. Therefore, the purpose of this study was to evaluate the production of biodiesel from two oil sources i.e. waste cooking oil and castor oil. This study examined the effect of mixed oil ratio on yield, biodiesel characteristics and stability. The physical properties included kinematic viscosity, acid number, saponification number, iodine number and cetane number have been evaluated as function of oil ratio. Yield of biodiesel was obtained at 35.07%, 99.2% and 83.69% for jatropha:castor oil ratio of 1: 0, 1: 2 and 2: 1, respectively. Most of these characteristics showed an increase by increasing the oil ratio. The result concluded that at the ratio of 1:1(v/v was the best characteristic and stability.

  10. Anaerobic treatment of wastewater from the household and personal products industry in a hybrid bioreactor

    Directory of Open Access Journals (Sweden)

    D. J. Araujo

    2008-09-01

    Full Text Available The anaerobic treatment of wastewater from the household and personal products industry was studied using a 16.3 L hybrid reactor (UASB and biofilter. The top of the UASB reactor was filled with coconut shells to act as the support material for the biofilter. The wastewater was characterized in terms of pH (1.0 - 12.0, COD (1,000 - 5,000 mg/L, BOD5 (700 - 1,500 mg/L, chloride (55 - 850 mg/L, ammonia nitrogen (0.4 - 0.9 mg/L, total Kjeldahl nitrogen (22.1 - 34.0 mg/L, phosphorus (2.0 - 2.5 mg/L, anionic surfactants (100 - 600 mg/L, turbidity (115 - 300 NTU and total suspended solids (450 - 1,440 mg/L. The bioreactor was operated continuously for 120 days at room temperature (26 ± 5ºC with hydraulic retention times of 50, 40 and 60 h. COD and BOD removals and biogas production were evaluated in order to analyze process efficiency. The average removal efficiencies for COD (77%, 72% and 80% and BOD5 (approximately 90% were obtained with HRTs of 50, 40 and 60 h, respectively. The average specific biogas production was 0.32 L/g COD (at standard temperature and pressure for the three experimental runs. These data indicate good reactor efficiency and suggest the possibility of using this system to treat wastewater generated by the household and personal products industry.

  11. Response to Oil Sands Products Assessment

    Science.gov (United States)

    2015-09-01

    clothing , and eye protection. The MSDS for natural gas condensate for Oneok (2009) warns that condensate, being denser than air, will accumulate in...with shovels and clippers and plastic bags collecting all this stuff.” Detergents were ineffective, Hamilton said (Schulte, 2013). 3.4.5 Lack of...oil, are pumped to these basins—or ponds— where settling occurs and water is recycled for reuse in the process. When the ponds are no longer required

  12. Effect of Sludge Concentration and Crude Glycerol Matrix as a Substrate on the Production of Single-Cell Oil by Oleaginous Yeast Yarrowia lipolytica SKY7

    Directory of Open Access Journals (Sweden)

    Saurabh Kumar Ram

    2018-04-01

    Full Text Available The disposal of excess crude glycerol produced by the booming biodiesel industry and wastewater sludge solid waste has become a severe problem, and alternate routes of use and valorization of these waste byproducts are needed. The use of cheaply available wastewater sludge solids in fermentation media is very much desirable to reduce the cost of production. The strains of Yarrowia lipolytica can assimilate a wide array of waste substrates, such as crude glycerol, waste cooking oil, starch wastewater, and cellulosic. This study optimized the concentration of wastewater sludge solids (5–35 g/L to be used with crude glycerol in fermentation media to produce microbial oil as feedstock for biodiesel production. The results indicated that 20 g/L of sludge solids with 40 g/L of crude glycerol resulted in highest lipid content of 29.35% in 96 h. Further, assuming wet extraction of lipids, it was found that at least 11.2% or higher lipid content is required for this process to have an overall positive net solid waste reduction. Insignificant inhibition was observed by the crude glycerol used in this study as compared to pure glycerol, which proves it to be an adequate source of carbon substrate for lipid production.

  13. Literature review on production process to obtain extra virgin olive oil enriched in bioactive compounds. Potential use of byproducts as alternative sources of polyphenols.

    Science.gov (United States)

    Frankel, Edwin; Bakhouche, Abdelhakim; Lozano-Sánchez, Jesús; Segura-Carretero, Antonio; Fernández-Gutiérrez, Alberto

    2013-06-05

    This review describes the olive oil production process to obtain extra virgin olive oil (EVOO) enriched in polyphenol and byproducts generated as sources of antioxidants. EVOO is obtained exclusively by mechanical and physical processes including collecting, washing, and crushing of olives, malaxation of olive paste, centrifugation, storage, and filtration. The effect of each step is discussed to minimize losses of polyphenols from large quantities of wastes. Phenolic compounds including phenolic acids, alcohols, secoiridoids, lignans, and flavonoids are characterized in olive oil mill wastewater, olive pomace, storage byproducts, and filter cake. Different industrial pilot plant processes are developed to recover phenolic compounds from olive oil byproducts with antioxidant and bioactive properties. The technological information compiled in this review will help olive oil producers to improve EVOO quality and establish new processes to obtain valuable extracts enriched in polyphenols from byproducts with food ingredient applications.

  14. Vegetable fats and oils as functional ingredients in meat products

    Directory of Open Access Journals (Sweden)

    Alfonso Totosaus

    2011-12-01

    Full Text Available Sausages are a widely consumed food in México, and due to their low fat content (ca. 10% they can be employed to enrich diet by including functional or nutraceutic ingredients as vegetable fats and oils. The replace or incorporation of vegetable fats or oils in cooked sausages is a way to improve their nutritional profile to offer functional meat products.

  15. Biopolymer Production Kinetics of Mixed Culture Using Wastewater Sludge as a Raw Material and the Effect of Different Cations on Biopolymer Applications in Water and Wastewater Treatment.

    Science.gov (United States)

    More, T T; Yan, S; Tyagi, R D; Surampalli, R Y

    2016-05-01

    Thirteen extracellular polymeric substances (EPS) producing bacterial strains were cultivated (as mixed culture) in the sterilized sludge (suspended solids of 25 g/L) and the batch fermentation was carried out. Mixed culture revealed a high specific growth rate of 0.35/hr. The EPS production rate was higher up to 24 hours, which gradually decreased with further incubation. The kinetic estimates demonstrated growth-associated EPS production. Broth EPS revealed higher flocculation activity when combined with different cations (Ca(2+), Mg(2+), Fe(3+), and Al(3+)) in river water (≥90%), municipal wastewater (≥90%), and brewery wastewater (≥80%), respectively. A low dose (5 to 40 mg/L) of trivalent cations was required to achieve higher flocculation compared to the divalent cations (50 to 250 mg/L). Flocculation performance of EPS was comparable to Magnafloc-155 (chemical polymer) and, hence, it could be used as a flocculant.

  16. Wastewater treatment

    Directory of Open Access Journals (Sweden)

    Ranđel N. Kitanović

    2013-10-01

    Full Text Available Quality of life on Earth in the future will largely depend on the amount of safe water. As the most fundamental source of life, water is relentlessly consumed and polluted. To halt this trend, many countries are taking extensive measures and investing substantial resources in order to stop the contamination of water and return at least tolerably good water quality to nature. The goal of water purification is to obtain clean water with the sewage sludge as a by-product. Clean water is returned to nature, and further treatment of sludge may be subject to other procedures. The conclusion of this paper is simple. The procedure with purified water is easily achievable, purified water is discharged into rivers, lakes and seas, but the problem of further treatment of sludge remains. This paper presents the basic methods of wastewater treatment and procedures for processing the products from contaminated water. The paper can serve as a basis for further elaboration. Water Pollution In order to ensure normal life of living creatures, the water in which they live or the water they use must have a natural chemical composition and natural features. When, as a result of human activities, the chemical composition of water and the ratio of its chemical elements significantly change, we say that water is polluted. When the pollutants come from industrial plants, we are talking about industrial wastewater, and when they come from households and urban areas, we are talking about municipal wastewater. Both contain a huge amount of pollutants that eventually end up in rivers. Then, thousands of defenseless birds, fish and other animals suffer, and environmental consequences become immeasurable. In addition, the waste fed to the water often ends up in the bodies of marine animals, so they can return to us as food. Thermal water pollution also has multiple effects on the changes in the wildlife composition of aquatic ecosystems. Polluted water can be purified by

  17. Economic potentials of oil palm products and weed control on ...

    African Journals Online (AJOL)

    A study was carried out at the Research Farm of National Root Crops Research Institute Umudike, southeastern Nigeria (05o, 29'N, 07o 33'E and 122 m above sea level), in 2015 and 2016 cropping seasons to study the economic potentials of oil palm products and weed control on sustainable turmeric production and some ...

  18. Remote methods of indicating oil products in natural waters

    Energy Technology Data Exchange (ETDEWEB)

    Shlyakhova, L A

    1981-01-01

    A survey is made of domestic and foreign publications covering remote methods of monitoring film petroleum products and oil in natural waters. The given methods are realized in practice with the use of different sections of the electromagnetic spectrum. Remote quality control of the natural waters at the modern level may be an indicator of water pollution with film petroleum products.

  19. Cleaning oil refining drainage waters out of emulsified oil products with thermic treated cedar nut shell

    Science.gov (United States)

    Pyatanova, P. A.; Adeeva, L. N.

    2017-08-01

    It was elaborated the ability of the sorbent produced by thermic treatment of cedar nut shell to destruct model and real first kind (direct) emulsions in static and dynamic conditions. In static conditions optimal ratio sorbent-emulsion with the original concentration of oil products 800 mg/l was in the range of 2.0 g per 100 ml of emulsion which corresponds to the level of treatment 94.9%. The time of emulsion destruction was 40 minutes. This sorbent is highly active in dynamic processes of oil-contaminated water treatment, the level of treatment 96.0% is being achieved. Full dynamic sorptive capacity of the sorbent is 0.85 g/g. Sorbent based on the thermic treated cedar nut shell can be elaborated as sorptive filter element of local treatment facilities of oil refining and petrochemical processes. After the treatment with this sorbent of drainage waters of oil refinery in dynamic conditions the concentration of oil products became less than mpc on oil products for waste waters coming to biological treatment.

  20. Bio-oil production through pyrolysis of blue-green algae blooms (BGAB): Product distribution and bio-oil characterization

    International Nuclear Information System (INIS)

    Hu, Zhiquan; Zheng, Yang; Yan, Feng; Xiao, Bo; Liu, Shiming

    2013-01-01

    Pyrolysis experiments of blue-green algae blooms (BGAB) were carried out in a fixed-bed reactor to determine the effects of pyrolysis temperature, particle size and sweep gas flow rate on pyrolysis product yields and bio-oil properties. The pyrolysis temperature, particle size and sweep gas flow rate were varied in the ranges of 300–700 °C, below 0.25–2.5 mm and 50–400 mL min −1 , respectively. The maximum oil yield of 54.97% was obtained at a pyrolysis temperature of 500 °C, particle size below 0.25 mm and sweep gas flow rate of 100 mL min −1 . The elemental analysis and calorific value of the oil were determined, and the chemical composition of the oil was investigated using gas chromatography–mass spectroscopy (GC–MS) technique. The analysis of bio-oil composition showed that bio-oil from BGAB could be a potential source of renewable fuel with a heating value of 31.9 MJ kg −1 . - Highlights: ► Bio-oil production from pyrolysis of blue-green algae blooms in fixed bed reactor. ► Effects of pyrolysis conditions on product distribution were investigated. ► The maximum bio-oil yield reached 54.97 wt %. ► The bio-oil has high heating value and may be suitable as renewable fuel. ► Pyrolysis of algal biomass beneficial for energy recovery, eutrophication control

  1. Past, Present, and Future Production of Bio-oil

    Energy Technology Data Exchange (ETDEWEB)

    Steele, Philip; Yu, Fei; Gajjela, Sanjeev

    2009-04-01

    Bio-oil is a liquid product produced by fast pyrol-ysis of biomass. The fast pyrolysis is performed by heating the biomass rapidly (2 sec) at temperatures ranging from 350 to 650 oC. The vapors produced by this rapid heating are then condensed to produce a dark brown water-based emulsion composed of frag-ments of the original hemicellulose, cellulose and lignin molecules contained in the biomass. Yields range from 60 to 75% based on the feedstock type and the pyrolysis reactor employed. The bio-oil pro-duced by this process has a number of negative prop-erties that are produced mainly by the high oxygen content (40 to 50%) contributed by that contained in water (25 to 30% of total mass) and oxygenated compounds. Each bio-oil contains hundreds of chemi-cal compounds. The chemical composition of bio-oil renders it a very recalcitrant chemical compound. To date, the difficulties in utilizing bio-oil have limited its commercial development to the production of liq-uid smoke as food flavoring. Practitioners have at-tempted to utilize raw bio-oil as a fuel; they have also applied many techniques to upgrade bio-oil to a fuel. Attempts to utilize raw bio-oil as a combustion engine fuel have resulted in engine or turbine dam-age; however, Stirling engines have been shown to successfully combust raw bio-oil without damage. Utilization of raw bio-oil as a boiler fuel has met with more success and an ASTM standard has recently been released describing bio-oil characteristics in relation to assigned fuel grades. However, commercialization has been slow to follow and no reports of distribution of these bio-oil boiler fuels have been reported. Co-feeding raw bio-oil with coal has been successfully performed but no current power generation facilities are following this practice. Upgrading of bio-oils to hydrocarbons via hydroprocessing is being performed by several organizations. Currently, limited catalyst life is the obstacle to commercialization of this tech-nology. Researchers

  2. Bioproducts for Sludge Reduction in Activated Sludge Systems Treating Oil Refinery Wastewater

    Directory of Open Access Journals (Sweden)

    Alexandre V.M.F.

    2016-03-01

    Full Text Available The use of bioproducts that change the cellular metabolism and reduce microbial growth without affecting the organic matter removal is very promising for reducing the amount of sludge in wastewater treatment systems. In this study, two bioproducts were evaluated and compared with a well-known chemical (2,4-DiNitroPhenol – DNP in activated sludge treating petroleum refinery wastewater. In batch experiments, 10 mg/L of DNP, 0.8 mg/L of a bioproduct based on Folic Acid (FA and 10 mg/L of a bioproduct based on Stress Proteins (SP led to 30.6%, 43.2% and 29.8% lower disposal of total solids, respectively. Operating on a continuous regimen, the addition of 10 mg/L of the bioproduct based on SP led to 45.7% lower disposal for 50 days. In all cases, no loss of efficiency in the Chemical Oxygen Demand (COD removal was observed.

  3. Quantifying nitrous oxide production pathways in wastewater treatment systems using isotope technology - A critical review.

    Science.gov (United States)

    Duan, Haoran; Ye, Liu; Erler, Dirk; Ni, Bing-Jie; Yuan, Zhiguo

    2017-10-01

    Nitrous oxide (N 2 O) is an important greenhouse gas and an ozone-depleting substance which can be emitted from wastewater treatment systems (WWTS) causing significant environmental impacts. Understanding the N 2 O production pathways and their contribution to total emissions is the key to effective mitigation. Isotope technology is a promising method that has been applied to WWTS for quantifying the N 2 O production pathways. Within the scope of WWTS, this article reviews the current status of different isotope approaches, including both natural abundance and labelled isotope approaches, to N 2 O production pathways quantification. It identifies the limitations and potential problems with these approaches, as well as improvement opportunities. We conclude that, while the capabilities of isotope technology have been largely recognized, the quantification of N 2 O production pathways with isotope technology in WWTS require further improvement, particularly in relation to its accuracy and reliability. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Cultivation of Chlorella vulgaris in a pilot-scale photobioreactor using real centrate wastewater with waste glycerol for improving microalgae biomass production and wastewater nutrients removal.

    Science.gov (United States)

    Ren, Hongyan; Tuo, Jinhua; Addy, Min M; Zhang, Renchuan; Lu, Qian; Anderson, Erik; Chen, Paul; Ruan, Roger

    2017-12-01

    To improve nutrients removal from real centrate wastewater and enhance the microalgae biomass production, cultivation of Chlorella vulgaris in lab and a pilot-scale photobioreactor with waste glycerol was studied. The results showed the optimal concentration of the crude glycerol was 1.0gL -1 with the maximum biomass productivity of 460mgL -1 d -1 TVS, the maximum lipid content of 27%, the nutrient removal efficiency of all above 86%, due to more balanced C/N ratio. The synergistic relationship between the wastewater-borne bacteria and the microalgae had significant good influence on nutrient removal. In pilot-scale wastewater-based algae cultivation, with 1gL -1 waste glycerol addition, the average biomass production of 16.7gm -2 d -1 , lipid content of 23.6%, and the removal of 2.4gm -2 d -1 NH 4 + -N, 2.7gm -2 d -1 total nitrogen, 3.0gm -2 d -1 total phosphorous, and 103.0gm -2 d -1 of COD were attained for 34days semi-continuous mode. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. Biodiesel production from corn oil by transesterification process

    International Nuclear Information System (INIS)

    Khan, N.A.; Dessouky, H.

    2009-01-01

    There is much political demand and economic pressure to convert agricultural surpluses into material, such as motor fuel, in which the world is deficient. Transport industry is primary consumer of crude oil. Due to scarcity of known petroleum reserves, the possible alternative fuel for use in present engine technology is biofuels. Europe, USA and Brazil are successfully using biofuels. Biofuels causes less environmental pollution as compared to normal petro fuels. As a fuel, ethanol (gasohol) is used in internal combustion engine while methyester (Biodiesel) is used in diesel engines with same or better performance as compared to petro fuels. Corn is very valuable crop with numerous industrial applications, and is used in more than 300 modern industries, including the manufacture of textiles, paper, adhesives, insecticides, paints, soaps, explosives and many more. Presently the biggest source of ethanol production is from corn (produced by USA). Edible oil can also be extracted from corn which is normally used for cooking and it can be used for biodiesel production. Many countries are experimenting on fats and oil to get feasible data for production of biodiesel. Presently USA prefer to use soybean oil as raw material for commercial production of biodiesel while in Europe rapeseed oil is preferred, so therefore, it depends upon the availability of raw material in particular area and may change from location to location. In Pakistan we started with corn oil to produce biodiesel by transesterification method. In present study different design parameters such as effect of temperature, catalyst concentration, molar ratio, and Stirrer speed were founded for better conversion of neat and used corn oil into biodiesel. The optimum parameters proposed for neat corn oil are 0.5% of catalyst based on weight of corn oil, temperature between 50 deg. C to 60 deg. C, reaction time 15 minutes, molar ratio of 6:1 and speed of stirrer 155 rpm. In case of used corn oil high catalyst

  6. Genotoxicity of the disinfection by-products resulting from peracetic acid- or hypochlorite-disinfected sewage wastewater.

    Science.gov (United States)

    Crebelli, R; Conti, L; Monarca, S; Feretti, D; Zerbini, I; Zani, C; Veschetti, E; Cutilli, D; Ottaviani, M

    2005-03-01

    Wastewater disinfection is routinely carried out to prevent the spread of human pathogens present in wastewater effluents. To this aim, chemical and physical treatments are applied to the effluents before their emission in water bodies. In this study, the influence of two widely used disinfectants, peracetic acid (PAA) and sodium hypochlorite (NaClO), on the formation of mutagenic by-products was investigated. Wastewater samples were collected before and after disinfection, in winter and in summer, at a pilot plant installed in a municipal wastewater-treatment plant. Samples were adsorbed using silica C18 cartridges and the concentrates were tested for mutagenicity in the Salmonella typhimurium reversion test with strains TA98 and TA100. Non-concentrated water samples were tested with two plant genotoxicity assays (the Allium cepa root anaphase aberration test and the Tradescantia/micronucleus test). Mutagenicity assays in bacteria and in Tradescantia showed borderline mutagenicity in some of the wastewater samples, independent of the disinfection procedure applied. Negative results were obtained in the A. cepa anaphase aberration test. These results indicate that, in the conditions applied, wastewater disinfection with PAA and NaClO does not lead to the formation of significant amounts of genotoxic by-products.

  7. Production of Biodiesel from Vegetable Oil Using Microware Irradiation

    Directory of Open Access Journals (Sweden)

    N. Kapilan

    2012-01-01

    Full Text Available The petroleum oil supply crisis, the increase in demand and the price eruption have led to a search for an alternative fuel of bio-origin in India. Among the alternative fuels, biodiesel is considered as a sustainable renewable alternative fuel to fossil diesel. Non-edible jatropha oil has considerable potential for the production of biodiesel in India. The production of biodiesel from jatropha oil using a conventional heating method takes more than 1h. In this work, microwave irradiation has been used as a source of heat for the transesterification reaction. A domestic microwave oven was modified and used for microwave heating of the reactants. The time taken for biodiesel production using microwave irradiation was 1 min. The fuel property analysis shows that the properties of jatropha oil biodiesel satisfy the biodiesel standards, and are close to the fossil diesel standards. From this work, it is concluded that biodiesel can be produced from vegetable oil using microwave irradiation, with a significant reduction in production time.

  8. Britain's North Sea oil and gas production: a critical review

    International Nuclear Information System (INIS)

    Odell, P.R.

    1996-01-01

    The size and longevity of Britain's offshore hydrocarbons resources have been underestimated. Gas reserves were seriously under-exploited for almost 20 years from the late 1960s, given a belief that gas should be used only as a premium fuel and in the context of an uncompetitive market. Oil reserves' development and production has suffered from time to time from inappropriate politico-economic conditions. Nevertheless, offshore oil and gas has come to dominate the UK's energy production over the past 20 years and currently accounts for 85% of the country's total energy output. Fears for resources' exhaustion remain unjustified, as the industry continues to replace oil and gas reserves used each year. The North Sea is still not comprehensively explored: the continuation of the process will enable oil production to remain at high levels and that of gas to expand further. Supplementary output from the new west of Shetland province will become progressively more important after 2000. But continued intensive production overall depends on the maintenance of attractive politico-economic conditions and on present oil prices. It also requires the European gas market to remain firm but, ironically, the planned flow of UK gas to the mainland constitutes a threat to this condition. (Author)

  9. Evaluation of a model for the removal of pharmaceuticals, personal care products, and hormones from wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Blair, Benjamin D. [School of Freshwater Sciences, University of Wisconsin-Milwaukee, 600 E. Greenfield Ave, Milwaukee, WI 53204 (United States); Crago, Jordan P. [Department of Biology, University of Wisconsin-Milwaukee, 600 E. Greenfield Ave, Milwaukee, WI 53204 (United States); Hedman, Curtis J. [State Laboratory of Hygiene, University of Wisconsin-Madison, 2601 Agriculture Drive, Madison, WI 53718 (United States); Treguer, Ronan J.F. [Veolia Water North America, 101 West Washington St., Ste. 1400 East, Indianapolis, IN 46204 (United States); Magruder, Christopher [Milwaukee Metropolitan Sewer District, 260 W. Seeboth St, Milwaukee, WI 53204 (United States); Royer, L. Scott [Veolia Water Milwaukee, 700 E. Jones St., Milwaukee, WI 53207 (United States); Klaper, Rebecca D., E-mail: rklaper@uwm.edu [School of Freshwater Sciences, University of Wisconsin-Milwaukee, 600 E. Greenfield Ave, Milwaukee, WI 53204 (United States)

    2013-02-01

    Current wastewater treatment processes are insufficient at removing many pharmaceutical and personal care products (PPCPs) from wastewater and it is necessary to identify the chemical characteristics that determine their fate. Models that predict the fate of various chemicals lack verification using in situ data, particularly for PPCPs. BIOWIN4 is a quantitative structure–activity relationship (QSAR) model that has been proposed to estimate the removal of PPCPs from wastewater, but data verifying the accuracy of its predictions is limited. In this study, the in situ soluble and suspended solid concentrations were assessed from raw influent, primary effluent, secondary effluent, and final effluent for 54 PPCPs and hormones over six dates. When assessing the removal efficiency across the different stages of the WWTP, the majority of the removal occurred across the secondary treatment process for the majority of the compounds. The primary treatment and disinfection process had limited impacts on the removal of most PPCPs. Sorption to solids was found to influence the removal for compounds with a log octanol–water partitioning coefficient greater than 4.5 across the secondary treatment process. For other compounds, the removal of PPCPs across the secondary treatment process was significantly correlated with the biodegradation predicted by BIOWIN4. Removal efficiencies across the aerobic secondary treatment process were predicted by integrating BIOWIN4 into pseudo-first order kinetics of PPCPs and these predicted values were compared to the in situ data. This study determines that under a certain set of operating conditions, two chemical characteristics — the expected hydrophobic interaction and the modeled biological degradation from BIOWIN4 — were found to predict the removal of highly degradable and recalcitrant PPCPs from a wastewater secondary treatment process. - Highlights: ► Fifty-six PPCPs were assessed across the stages of a wastewater treatment

  10. Modeling and Multiresponse Optimization for Anaerobic Codigestion of Oil Refinery Wastewater and Chicken Manure by Using Artificial Neural Network and the Taguchi Method

    Directory of Open Access Journals (Sweden)

    Esmaeil Mehryar

    2017-01-01

    Full Text Available To study the optimum process conditions for pretreatments and anaerobic codigestion of oil refinery wastewater (ORWW with chicken manure, L9 (34 Taguchi’s orthogonal array was applied. The biogas production (BGP, biomethane content (BMP, and chemical oxygen demand solubilization (CODS in stabilization rate were evaluated as the process outputs. The optimum conditions were obtained by using Design Expert software (Version 7.0.0. The results indicated that the optimum conditions could be achieved with 44% ORWW, 36°C temperature, 30 min sonication, and 6% TS in the digester. The optimum BGP, BMP, and CODS removal rates by using the optimum conditions were 294.76 mL/gVS, 151.95 mL/gVS, and 70.22%, respectively, as concluded by the experimental results. In addition, the artificial neural network (ANN technique was implemented to develop an ANN model for predicting BGP yield and BMP content. The Levenberg-Marquardt algorithm was utilized to train ANN, and the architecture of 9-19-2 for the ANN model was obtained.

  11. Indications of Transformation Products from Hydraulic Fracturing Additives in Shale Gas Wastewater

    Science.gov (United States)

    Elsner, Martin; Hoelzer, Kathrin; Sumner, Andrew J.; Karatum, Osman; Nelson, Robert K.; Drollette, Brian D.; O'Connor, Megan P.; D'Ambro, Emma; Getzinger, Gordon J.; Ferguson, P. Lee; Reddy, Christopher M.; Plata, Desiree L.

    2016-04-01

    Unconventional natural gas development (UNGD) generates large volumes of wastewater, whose detailed composition must be known for adequate risk assessment and treatment. In particular, there is a need to elucidate the structures of organic chemical additives, extracted geogenic compounds, and transformation products. This study investigated six Fayetteville Shale UNGD wastewater samples for their organic composition using purge-and-trap gas chromatography-mass spectrometry (P&T-GC-MS) in combination with liquid-liquid extraction with comprehensive two-dimensional gas chromatography-time of flight-mass spectrometry (GCxGC-TOF-MS). Following application of strict compound identification confidence criteria, we classified compounds according to their putative origin. Samples displayed distinct chemical distributions composed of typical geogenic substances (hydrocarbons), disclosed UNGD additives (e.g., hydrocarbons, phthalates, such as diisobutyl phthalate, and radical initiators, such as azobisisobutyronitrile), and undisclosed compounds (e.g., halogenated hydrocarbons, such as 2-bromohexane or 4-bromoheptane). Undisclosed chloromethyl alkanoates (chloromethyl propanoate, pentanoate, and octanoate) were identified as putative delayed acids (those that release acidic moieties only after hydrolytic cleavage, whose rate could potentially be controlled), suggesting they were deliberately introduced to react in the subsurface. Identification of halogenated methanes and acetones, in contrast, suggested they were formed as unintended by-products. Our study highlights the possibility that UNGD operations generate transformation products, knowledge of which is crucial for risk assessment and treatment strategies, and underscores the value of disclosing potential precursors that are injected into the subsurface.

  12. Activated sludge is a potential source for production of biodegradable plastics from wastewater.

    Science.gov (United States)

    Khardenavis, A; Guha, P K; Kumar, M S; Mudliar, S N; Chakrabarti, T

    2005-05-01

    Increased utilization of synthetic plastics caused severe environmental pollution due to their non-biodegradable nature. In the search for environmentally friendly materials to substitute for conventional plastics, different biodegradable plastics have been developed by microbial fermentations. However, limitations of these materials still exist due to high cost. This study aims at minimization of cost for the production of biodegradable plastics P(3HB) and minimization of environmental pollution. The waste biological sludge generated at wastewater treatment plants is used for the production of P(3HB) and wastewater is used as carbon source. Activated sludge was induced by controlling the carbon: nitrogen ratio to accumulate storage polymer. Initially polymer accumulation was studied by using different carbon and nitrogen sources. Maximum accumulation of polymer was observed with carbon source acetic acid and diammonium hydrogen phosphate (DAHP) as nitrogen source. Further studies were carried out to optimize the carbon: nitrogen ratios using acetic acid and DAHP. A maximum of 65.84% (w/w) P(3HB) production was obtained at C/N ratio of 50 within 96 hours of incubation.

  13. Evaluation of hardboard manufacturing process wastewater as a feedstream for ethanol production.

    Science.gov (United States)

    Groves, Stephanie; Liu, Jifei; Shonnard, David; Bagley, Susan

    2013-07-01

    Waste streams from the wood processing industry can serve as feedstream for ethanol production from biomass residues. Hardboard manufacturing process wastewater (HPW) was evaluated on the basis of monomeric sugar recovery and fermentability as a novel feedstream for ethanol production. Dilute acid hydrolysis, coupled with concentration of the wastewater resulted in a hydrolysate with 66 g/l total fermentable sugars. As xylose accounted for 53 % of the total sugars, native xylose-fermenting yeasts were evaluated for their ability to produce ethanol from the hydrolysate. The strains selected were, in decreasing order by ethanol yields from xylose (Y p/s, based on consumed sugars), Scheffersomyces stipitis ATCC 58785 (CBS 6054), Pachysolen tannophilus ATCC 60393, and Kluyveromyces marxianus ATCC 46537. The yeasts were compared on the basis of substrate utilization and ethanol yield during fermentations of the hydrolysate, measured using an HPLC. S. stipitis, P. tannophilus, and K. marxianus produced 0.34, 0.31, and 0.36 g/g, respectively. The yeasts were able to utilize between 58 and 75 % of the available substrate. S. stipitis outperformed the other yeast during the fermentation of the hydrolysate; consuming the highest concentration of available substrate and producing the highest ethanol concentration in 72 h. Due to its high sugar content and low inhibitor levels after hydrolysis, it was concluded that HPW is a suitable feedstream for ethanol production by S. stipitis.

  14. Process for reducing halogen impurities in oil products

    Energy Technology Data Exchange (ETDEWEB)

    Basler, F.

    1990-08-14

    Oil products, in particular waste oils, may be efficiently reprocessed according to an economic and technically simple method for removing impurities, notably halogens. In this method, the oil product is treated at temperatures up to about 150{degree}C with an effective amount of an aqueous solution of at least one compound selected from the group consisting of a strong acid, a salt of a weak base and a strong acid and precursors thereof. The oil product obtained in this step is treated at increased temperatures with at least one halogen binding agent. The water and/or solids from the product so treated are separated out. The process of the invention can be carried out in a conventional stripping apparatus. The strong acid used in the first step is preferably selected from sulfurous acid, phosphoric acid, phosphorous acid, and phosphonic acid. The salt of the weak base and strong acid is preferably ammonium sulfate, ammonium bisulfate, ammonium sulfite, diammonium hydrogen phosphate, ammonium dihydrogen phosphate, ammonium phosphite, and ammonium phosphonic acid. The second step of the method is preferably a coagulation step in which organic halogen compounds break down into hydrogen halides which are neutralized by the added halogen binding agents. The preferred halogen binding agents are ammonia and/or an organic base. The coagulation is preferably carried out in heat exchangers so that the oil is heated in 3 stages and the oil from each stage is passed through a cascade tower. In the third step, additives may be used to enhance separation of the oil. Experiments are described to illustrate the method of the invention. 1 tab.

  15. BIOSURFACTANTS PRODUCTION BY Pseudomonas aeruginosa USING SOYBEAN OIL AS SUBSTRATE

    Directory of Open Access Journals (Sweden)

    Venty Suryanti

    2010-06-01

    Full Text Available Optimization condition of the biosurfactants production by P. aeruginosa using soybean oil as substrate has been examined. The media containing 10% v/v of the soybean oil and 6 days of the fermentation time was the optimum condition for the biosurfactants production. The extraction technique using different solvent polarity (n-hexane, chloroform, ethyl acetate and buthanol, respectively was applied for the isolation of the biosurfactants. The biosurfactant was found in the extract chloroform of the crude biospasoy (biosurfactants obtained from soybean oil as substrate which then is called chlo-biospasoy. The chlo-biospasoy was identified as rhamnolipids which had oil in water (o/w emulsion type, had the CMC of 860 mg/L and could reduced the surface tension of the water from 72 mN/m to 52 mN/m. The chlo-biospasoy could be used as an emulsifier to form emulsion between water and hydrocarbon such as palm oil, benzene, premium or toluene with various stability. The results indicated that chlo-biospasoy could be used as an emulsifying and emulsion-stabilizing agent.     Keywords: Biosurfactants, P. aeruginosa, Soybean Oil, Emulsifier

  16. Treatment of hydrocarbon-rich wastewater using oil degrading bacteria and phototrophic microorganisms in rotating biological contactor: Effect of N:P ratio

    International Nuclear Information System (INIS)

    Chavan, Anal; Mukherji, Suparna

    2008-01-01

    Treatment of hydrocarbon-rich industrial wastewater in bioreactors using heterotrophic microorganisms is often associated with various operational problems. In this study, a consortium of phototrophic microorganisms and a bacterium is developed on the discs of a rotating biological contactor (RBC) for treatment of wastewater containing diesel oil. The reactor was fed with oil degrading bacterium, Burkholderia cepacia and oil tolerant phototrophic microorganisms. After biofilm formation and acclimatization to 0.6% (v/v) diesel, continuous-mode operation was initiated at 21 h hydraulic retention time (HRT). Residual diesel in the effluent was 0.003%. Advantages of this system include good total petroleum hydrocarbon (TPH) removal, no soluble carbon source requirement and good settleability of biosolids. Biofilm observations revealed the predominance of B. cepacia and cyanobacteria (Phormidium, Oscillatoria and Chroococcus). The N:P ratio affected the relative dominance of the phototrophic microorganisms and bacterial culture. This ratio was a critical factor in determining the performance efficiency of the reactor. At 21 h HRT and organic loading of 27.33 g TPH/m 2 d, the N:P ratio 28.5:1 and 38:1 both yielded high and almost comparable TPH and COD removal efficiencies. This study presents a feasible technology for the treatment of hydrocarbon-rich wastewater from petrochemical industries and petroleum refineries

  17. Environmental Compliance for Oil and Gas Exploration and Production

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, Christine

    1999-10-26

    The Appalachian/Illinois Basin Directors is a group devoted to increasing communication among the state oil and gas regulatory agencies within the Appalachian and Illinois Basin producing region. The group is comprised of representatives from the oil and gas regulatory agencies from states in the basin (Attachment A). The directors met to discuss regulatory issues common to the area, organize workshops and seminars to meet the training needs of agencies dealing with the uniqueness of their producing region and perform other business pertinent to this area of oil and gas producing states. The emphasis of the coordinated work was a wide range of topics related to environmental compliance for natural gas and oil exploration and production.

  18. Studies of Terminalia catappa L. oil: characterization and biodiesel production.

    Science.gov (United States)

    Dos Santos, I C F; de Carvalho, S H V; Solleti, J I; Ferreira de La Salles, W; Teixeira da Silva de La Salles, K; Meneghetti, S M P

    2008-09-01

    Since the biodiesel program has been started in Brazil, the investigation of alternative sources of triacylglycerides from species adapted at semi-arid lands became a very important task for Brazilian researchers. Thus we initiated studies with the fruits of the Terminalia catappa L (TC), popularly known in Brazil as "castanhola", evaluating selected properties and chemical composition of the oil, as well any potential application in biodiesel production. The oil was obtained from the kernels of the fruit, with yields around 49% (% mass). Also, its fatty acid composition was quite similar to that of conventional oils. The crude oil of the TC was transesterified, using a conventional catalyst and methanol to form biodiesel. The studied physicochemical properties of the TC biodiesel are in acceptable range for use as biodiesel in diesel engines.

  19. Biodiesel Production from Acidified Oils via Supercritical Methanol

    Directory of Open Access Journals (Sweden)

    Jianxin Li

    2011-12-01

    Full Text Available In biodiesel production, the vegetable oil used as raw material for transesterification should be free of water and free fatty acids (FFAs, which may consume catalyst and reduce catalyst efficiency. In this work biodiesel was prepared from acidified oils (AO through a supercritical methanol route, in which the esterification of FFAs and transesterification of glyceride with methanol occurred simultaneously. The effects of the mass ratio of methanol to AO, the operation temperature as well as the water content on the FFAs conversion and glycerol yield were investigated. The results indicated that the FFAs conversion for esterification under the condition of 1:1 methanol/oil ratio, 310 °C and 15 min reaction time reached 98.7%, and the glycerol yield for transesterification under 0.25:1 methanol/oil ratio, 290 °C and 20 min reaction time reached 63.5% respectively.

  20. Production of bio diesel from chicken frying oil

    International Nuclear Information System (INIS)

    Bakir, E.T.; Fadhil, A.B.

    2011-01-01

    Chicken fried oil was converted into different bio diesels through single step transesterification and two step transesterification, namely acid-base and base-base catalyzed transesterification. Hydrochloric acid and potassium hydroxide with methanol were used for this purpose. The results showed that two step base catalyzed transesterification was better compared to other methods. It resulted in higher yield and better fuel properties. Transesterification of fried chicken oil was monitored by TLC technique and compared with that of the parent oil. Fuel properties of the products have been measured and found markedly enhanced compared to those of the parent oil. Also, the values satisfied the standard limits according to the ASTM standards. Blending of the better bio diesel sample with petro diesel was made using three volume percentages (10, 30 and 50% v/v). The results disclosed that blending had slight effect on the original properties of petro diesel.

  1. Codigestion of olive oil mill wastewaters with manure, household waste or sewage sludge

    DEFF Research Database (Denmark)

    Angelidaki, I.; Ahring, B.K.

    1997-01-01

    Combined anaerobic digestion of oil mill effluent (OME) together with manure, household waste (HHW) or sewage sludge was investigated. In batch experiments it was shown that OME could be degraded into biogas when codigested with manure. In codigestion with HHW or sewage sludge, OME dilution...

  2. Castor and jatropha oils: production strategies – A review

    Directory of Open Access Journals (Sweden)

    Lago Regina C.A.

    2009-07-01

    Full Text Available The Brazilian bioenergy matrix is based on four platforms: ethanol, energy forests, residues and co-products and biodiesel. The food-energy dichotomy in the use of edible oils is one factor which has stimulated the search for non-edible oleaginous energy crops, such as many native palms. By the year 2000 Brazil had an annual deficit of 80 thousand tons of castor oil, making necessary to import oil from China and India. After a strong debate the National Program on Biodiesel Production (NPBP was launched by December 2004. After an initial excessive enthusiasm, small producers being focused in the program, a more mature and realistic planning is undertaken. Production in semi arid lands is being stimulated, mainly castor (Ricinus communis and Jatropha (Jatropha curcas. Apart from belonging to the same botanical family (Euphorbiaceae, both plants are well resistant to poor soils. Castor plant is well adapted to practically the whole country, except for some extreme areas (too low water availability or too much rain. Castor keeps being an alternative for the semi arid region but much more technology is requested to make it largely exploited. Following the petroleum crisis of 1980’s an ambitious research program on Jatropha curcas was initiated, later on discontinued and presently retaken by Embrapa and some Universities. Progress is slower than in the case of Ricinus communis. The first agronomical observations confirmed low productivity, problems with pests and diseases, high harvesting costs etc. Some strategic factors should be considered for the production of castor and Jatropha oils: 1. Production of raw materials; 2. Production of oils; 3. Detoxification and value aggregation to the extraction cakes and residues. Regarding raw material production, it is necessary a strong, long term research program on genetic breeding (short cycle varieties, with high productivity and allowing a sole harvesting, soil fertility, pest control, domestication

  3. Production possibility frontier analysis of biodiesel from waste cooking oil

    International Nuclear Information System (INIS)

    Kagawa, Shigemi; Takezono, Kanako; Suh, Sangwon; Kudoh, Yuki

    2013-01-01

    This paper presents an assessment of the productive efficiency of an advanced biodiesel plant in Japan using Data Envelopment Analysis (DEA). The empirical analysis uses monthly input data (waste cooking oil, methanol, potassium hydroxide, power consumption, and the truck diesel fuel used for the procurement of waste cooking oil) and output data (biodiesel) of a biodiesel fuel plant for August 2008–July 2010. The results of this study show that the production activity with the lowest cost on the biodiesel production possibility frontier occurred in March 2010 (production activity used 1.41 kL of waste cooking oil, 0.18 kL of MeOH, 16.33 kg of KOH, and 5.45 kW h of power), and the unit production cost in that month was 18,517 yen/kL. Comparing this efficient production cost to the mean unit production cost on the production possibility frontier at 19,712 yen/kL, revealed that the cost of producing 1 kL of biodiesel could be reduced by as much as 1195 yen. We also find that the efficiency improvement will contribute to decreasing the cost ratio (cost per sale) of the biodiesel production by approximately 1% during the study period (24 months) between August 2008 and July 2010. - Highlights: ► This paper analyzes the productive efficiency of an advanced biodiesel plant using DEA. ► We examine the optimal production activities of biodiesel from waste cooking oil. ► Considering the production frontier, the unit cost of biodiesel could be reduced by 1195 yen. ► The efficiency improvement contributes to decreasing the cost ratio of the biodiesel by 1%

  4. Impact of Expanded North Slope of Alaska Crude Oil Production on Crude Oil Flows in the Contiguous United States

    Energy Technology Data Exchange (ETDEWEB)

    DeRosa, Sean E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Flanagan, Tatiana Paz [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-05-01

    The National Transportation Fuels Model was used to simulate a hypothetical increase in North Slope of Alaska crude oil production. The results show that the magnitude of production utilized depends in part on the ability of crude oil and refined products infrastructure in the contiguous United States to absorb and adjust to the additional supply. Decisions about expanding North Slope production can use the National Transportation Fuels Model take into account the effects on crude oil flows in the contiguous United States.

  5. Impact of Optimized Flow Pattern on Pollutant Removal and Biogas Production Rate Using Wastewater Anaerobic Fermentation

    Directory of Open Access Journals (Sweden)

    Ruyi Huang

    2015-06-01

    Full Text Available This paper introduces a new-type of antigravity mixing method, which was applied in the biogas production process, using organic wastewater fermentation. It was found that the digesters with two designs, a high-position, centralized pressure outlet and a high-position, dispersed pressure outlets, both lead to an increase in biogas production rates by 89% and 125%, respectively. The biogas production peak appeared 1 day and 7 days earlier, and the COD removal rates were raised by 27% and 42%, respectively. The results indicated that the optimized flow field had a significant impact. This work also explains the mechanism of flow field optimization using computational fluid dynamics (CFD software for the simulation of the flow field form in the hydraulic mixing.

  6. Biological hydrogen production from probiotic wastewater as substrate by selectively enriched anaerobic mixed microflora

    Energy Technology Data Exchange (ETDEWEB)

    Sivaramakrishna, D.; Sreekanth, D.; Himabindu, V. [Centre for Environment, Institute of Science and Technology, Jawaharlal Nehru Technological University, Kukatpally, Hyderabad 500072, Andhra Pradesh (India); Anjaneyulu, Y. [TLGVRC, JSU Box 18739, JSU, Jackson, MS 32917-0939 (United States)

    2009-03-15

    Biohydrogen production from probiotic wastewater using mixed anaerobic consortia is reported in this paper. Batch tests are carried out in a 5.0 L batch reactor under constant mesophillic temperature (37 C). The maximum hydrogen yield 1.8 mol-hydrogen/mol-carbohydrate is obtained at an optimum pH of 5.5 and substrate concentration 5 g/L. The maximum hydrogen production rate is 168 ml/h. The hydrogen content in the biogas is more than 65% and no significant methane is observed throughout the study. In addition to hydrogen, acetate, propionate, butyrate and ethanol are found to be the main by-products in the metabolism of hydrogen fermentation. (author)

  7. Side-stream products of edible oil refining as feedstocks in biodiesel production

    Directory of Open Access Journals (Sweden)

    Cvetković Bojan S.

    2016-01-01

    Full Text Available Biodiesel, a diesel fuel alternative, is produced from vegetable oils and animal fats by the transesterification reaction of triacylglycerols and lower aliphatic alcohols. Beside number advantages related to fossil fuels, the main barrier to biodiesel wider commercial use is the high price of edible oils. Recently, the special attention was given to side-stream products of edible oil refining as low-cost triacylglycerol sources for biodiesel production because of their positive economic and ecological effects. In this paper, the different procedures for biodiesel production from side-stream refining products such as soapstock, spent bleaching earth and deodorizer distillate were analyzed. The main goal of this paper is to analyze the possibilities for reusing the by-products of edible oil refinement in the biodiesel production.

  8. Production of biodiesel from vegetable oils

    Directory of Open Access Journals (Sweden)

    Luque, Susana

    2008-03-01

    Full Text Available Biodiesel is produced by transesterification of triglycerides present in animal fat or vegetable oils, by displacing glycerine with a low molar mass alcohol. This resulting ester mixture has physico-chemical properties similar to those of petroleum diesel. This paper reviews the synthetic paths that lead to biodiesel by means of the catalytic transesterification of vegetable oils. Although methyl esters are at present the only ones produced at industrial scale, the use of ethanol, which can also be obtained from renewable resources, has been considered, since it would generate a cleaner and more biocompatible fuel.El biodiésel se produce mediante la transesterificación de triglicéridos, presentes en grasas animales o aceites vegetales, en un proceso en el que un alcohol de bajo peso molecular desplaza a la glicerina. La mezcla de esteres así resultante posee unas propiedades físico-químicas similares a las del diésel procedente de petróleo. En este artículo se revisan las vías de síntesis de biodiésel mediante la transesterificación catalítica de aceites vegetales. Aunque actualmente a escala industrial solo se producen ésteres metílicos, también se ha considerado el uso de etanol, ya que éste se obtiene también de fuentes renovables, generando así un combustible más limpio y biocompatible.

  9. Natural Occurrence of Aldol Condensation Products in Valencia Orange Oil.

    Science.gov (United States)

    Abreu, Ingo; Da Costa, Neil C; van Es, Alfred; Kim, Jung-A; Parasar, Uma; Poulsen, Mauricio L

    2017-12-01

    Cold pressed orange oils contain predominantly d-limonene (approximately 95%) and various other lower concentration monoterpenes, sesquiterpenes, sinensals plus 3 key aliphatic aldehydes: hexanal, octanal. and decanal. The aldol self-condensation products or "dimers" for each aldehyde have been postulated as being present at low concentrations in the oil. However, to date only the hexanal dimer has been previously reported. In this paper, cold pressed Valencia orange oil was fractionally distilled/folded and analyzed by GC and high resolution GC-MS to detect these compounds on 2 different capillary column phases. Subsequently the hexanal, octanal, and decanal self-aldol condensation products, 2-butyl-2-octenal, 2-hexyl-2-decenal, and 2-octyl-2-dodecenal, respectively, were detected in the folded oil. These predominantly trans configuration isomeric compounds were synthesized, to confirm them as being present in nature and evaluated organoleptically by a panel of evaluators. To further confirm the mechanism of their formation, the enriched oil was made into a simple beverage to show the effect on the formation of these aldol compounds under acidic conditions. Finally aliphatic aldehydes from hexanal to undecanal were reacted together in various combinatorial pairs to give an additional 33 self and mixed aldol condensation products, some of which were also detected in the folded oil. This paper discloses the structural elucidation and synthesis of 8 novel aldol condensation products found at trace concentrations in citrus and leading to a further 31 mass spectrally determined aldol products. Sensory evaluations and application of some of these components were demonstrated in a model citrus beverage. © 2017 Institute of Food Technologists®.

  10. Specific radiological monitoring (SRM) in oil and gas production platforms

    International Nuclear Information System (INIS)

    Hairul Nizam Idris, Syed Asraf Fahlawi Wafa S.M Ghazi and Fadzley Izwan Abd Manaf

    2007-01-01

    Technologically enhanced naturally occurring radioactive materials (TENORM) are present in components of both oil and natural gas production facilities. TENORM can be associated with the presence of crude oil, produced water and natural gas. The radiation exposure pathways to the workers in oil and gas production are similar to those in the uranium and heavy mineral sand mining and processing industry. This paper work provides a short review on the Specific Radiological Monitoring (SRM) program were carried out at oil and gas platforms in the east cost of Peninsular Malaysia. The objective of this paper work is to observe the monitoring parameters levels and to evaluate whether these levels are exceeding the limits set by Atomic Energy Licensing Board (AELB). The monitoring results showed that the surface contamination, airborne contamination and concentration of radon and thoron are well below the set limit stipulated in LEM/TEK/30 SEM.2, except for external radiation and radioactivity concentration of sludge and scales. About 2 (2.35%) from the 85 external radiation measurements performed were found above the permissible limit. While about 11 (36.6%) and 7 (23.3%) of the 30 collected sludge and scales samples were found containing higher Ra-226 and Ra-228, respectively, than the mean concentrations in normal soils of Peninsular Malaysia. In general, it can be concluded that a few of oil and gas production platform are producing TENORM. (Author)

  11. Indonesia palm oil production without deforestation and peat conversion by 2050

    NARCIS (Netherlands)

    Afriyanti, Dian; Kroeze, Carolien; Saad, Asmadi

    2016-01-01

    Palm oil is a promising source of cooking oil and biodiesel. The demand for palm oil has been increasing worldwide. However, concerns exist surrounding the environmental and socio-economic sustainability of palm oil production. Indonesia is a major palm oil producing country. We explored

  12. Comparative techno-economic analysis of biohydrogen production via bio-oil gasification and bio-oil reforming

    International Nuclear Information System (INIS)

    Zhang, Yanan; Brown, Tristan R.; Hu, Guiping; Brown, Robert C.

    2013-01-01

    This paper evaluates the economic feasibility of biohydrogen production via two bio-oil processing pathways: bio-oil gasification and bio-oil reforming. Both pathways employ fast pyrolysis to produce bio-oil from biomass stock. The two pathways are modeled using Aspen Plus ® for a 2000 t d −1 facility. Equipment sizing and cost calculations are based on Aspen Economic Evaluation® software. Biohydrogen production capacity at the facility is 147 t d −1 for the bio-oil gasification pathway and 160 t d −1 for the bio-oil reforming pathway. The biomass-to-fuel energy efficiencies are 47% and 84% for the bio-oil gasification and bio-oil reforming pathways, respectively. Total capital investment (TCI) is 435 million dollars for the bio-oil gasification pathway and is 333 million dollars for the bio-oil reforming pathway. Internal rates of return (IRR) are 8.4% and 18.6% for facilities employing the bio-oil gasification and bio-oil reforming pathways, respectively. Sensitivity analysis demonstrates that biohydrogen price, biohydrogen yield, fixed capital investment (FCI), bio-oil yield, and biomass cost have the greatest impacts on facility IRR. Monte-Carlo analysis shows that bio-oil reforming is more economically attractive than bio-oil gasification for biohydrogen production. -- Highlights: ► Biohydrogen production via bio-oil reforming has higher energy efficiency compared to gasification. ► Hydrogen price, fixed capital cost, and feedstock cost most strongly affect IRR. ► Lower risk investment is biohydrogen production via bio-oil reforming

  13. Characterization of residual oils for biodiesel production

    Directory of Open Access Journals (Sweden)

    Edmilson Antonio Canesin

    2014-01-01

    Conclusions: The obtained results suggesting that it is possible to take advantage of these residues for biodiesel production as the obtained products were approved according to the rules established by the National Association of Petroleum (ANP; the bovine samples were the exception regarding moisture and acidity.

  14. Design and development of decentralized water and wastewater technologies: a combination of safe wastewater disposal and fertilizer production.

    Science.gov (United States)

    Fach, S; Fuchs, S

    2010-01-01

    Modern wastewater treatment plants are often inappropriate for communities in developing countries. Such communities lack the funding, resources and skilled labour required to implement, operate, and maintain these plants. This research was conducted to investigate and establish an appropriate wastewater treatment system for the district of Gunung Kidul, Indonesia. Due to its lack of water during the dry season, this district is considered one of the poorest areas in the nation. First, wastewater was stored in septic tank units for a retention time of 26 days. Anaerobic conditions occurred, resulting in an 80% reduction of initial COD. The retained sludge was well stabilized with great potential, if dewatered, for reuse as fertilizer. Consequently, supernatant was separated for experiments consisting of lab scale aerobic sand filtering unit. Through filtration, further removals of COD (about 30%) and pathogens were achieved. Rich in nitrogen, the resulting effluent could be used for irrigation and soil conditioning. With faecal sludge and also a mixture of septic sludge and food waste, the hydrolysis stage of anaerobic digestion was examined. This paper discusses the laboratory findings in Karlsruhe and the design and implementation of a treatment system in Glompong, Indonesia.

  15. Oil refining and product marketing developments in Southeast Asia

    International Nuclear Information System (INIS)

    Szabo, A.M.

    1991-01-01

    It is estimated that the high growth rate in oil demand in the Asia-Pacific region (excluding Japan) will slow down slightly but still outperform the rest of the world during 1990-2000. This is expected to be true for southeast Asia as well, or more specifically the Association of Southeast Asian Nations (ASEAN). The region's dependence on oil imports from the Middle East will continue for the foreseeable future. Asia-Pacific crude oil production is expected to grow to 6.8 million bbl/d by 1995 and to 7.3 million bbl/d by 2000, meaning that the region will import nearly 50% of its crude oil requirements at both 1995 and 2000. The participation of ASEAN in the production of indigenous crudes in the Asia-Pacific region will increase from 31% in the mid-1980s to 41% by 2000. The Asia-Pacific imbalance between refinery output or supplies and demand patterns will be accentuated during the decade, providing significant opportunities for investments and/or product trading. The region will require upgrading facilities to generate an additional 3.7 million bbl/d of light products in 1995. In the ASEAN countries, surpluses in refined products are expected for 1995. Environmental concerns are following similar trends in the Asia-Pacific region as in the rest of the world, and the proportion of high aromatics gasolines produced will increase as the proportion of leaded gasoline decreases. 6 tabs

  16. Production of Biodiesel from Locally Available Spent Vegetable Oils

    Directory of Open Access Journals (Sweden)

    Mohamed Mostafa Al Naggar

    2017-06-01

    Full Text Available The depletion of fossil fuels prompted considerable research to find alternative fuels. Due its environmental benefits and renewable nature the production of biodiesel has acquired increasing importance with a view to optimizing the production procedure and the sources of feedstock. Millions of liters of waste frying oil are produced from local restaurants and houses every year, most are discarded into sewage systems causing damage to the networks.  This study is intended to consider aspects related to the feasibility of the production of biodiesel from waste frying oils which will solve the problem of waste frying oil pollution and reduce the cost of biodiesel production.This research studies the conversion of locally available spent vegetable oils of different origins and with different chemical compositions into an environmentally friendly fuel. The biodiesel production requirements by base catalyzed trans-esterification process for the different feed stocks are determined according to the measured physical properties. The quality of the produced biodiesel is compared to petro diesel in terms of established standard specifications.

  17. Utilization of Shochu distillery wastewater for production of polyunsaturated fatty acids and xanthophylls using thraustochytrid.

    Science.gov (United States)

    Yamasaki, Takashi; Aki, Tsunehiro; Shinozaki, Masami; Taguchi, Masahiro; Kawamoto, Seiji; Ono, Kazuhisa

    2006-10-01

    The industrial production of barley shochu, a distilled alcoholic beverage, results in distillery waste that is currently incinerated or disposed of in landfills, causing environmental pollution. The supernatant of distillery waste contains organic matter such as proteins ( approximately 2.5%) and amino acids ( approximately 0.2%). This study demonstrates that the utilization of distillery wastewater as a sole nitrogen source enables a marine thraustochytrid, Schizochytrium sp. strain KH105, to propagate and accumulate valuable lipids including docosahexaenoic acid (DHA) and astaxanthin. Under optimized culture conditions, the highest DHA and astaxanthin yields were obtained at 3.4 g/l and 7.7 mg/l, respectively, after 4 or 5 d of cultivation in a 3-l jar fermentor. The chemical oxygen demand of the wastewater was reduced by 35%. About 67% of crude protein content and 85% of total free amino acid content also decreased in the culture supernatant. The thraustochytrid therefore serves to upgrade the distillery by-product to one containing value-added lipids for functional foods as well as to regulate the environmental contamination.

  18. VAT: ways of improving administration and calculation during transshipment and transfer of oil and oil products

    Directory of Open Access Journals (Sweden)

    Vasiliy F. Stoykov

    2017-12-01

    Full Text Available Objective to eliminate legal uncertainty in interpretation and implementation of a legal norm para. 4 subclause 2.2. clause 1 Art. 164 of the Taxation Code of the Russian Federation to elaborate proposals for improving the Russian legislation on taxes and duties which is essential for elimination of the said problems. Methods the research is based on a set of general scientific and specific methods of cognition used in the science of Financial Law dialectic method formaldogmatic method methods of analysis analogy induction and synthesis historical retrospective formalization and logical method. Results the article presents theoreticallegal analysis of the consequences of ambiguous interpretation of a legal norm para. 4 subclause 2.2. clause 1 Art. 164 of the Taxation Code of the Russian Federation in relation to organizations rendering services in the sphere of oil and oil products transportation and transshipment. It is stated that one of the essential problems in the practice of value added tax implementation is the use of zero tax rate. When the norms of the above Article are interpreted it causes problems in organizations engaged in oil and oil products transportation and transshipment due to the differences in positions of the Russian Ministry of Finance and the taxation authorities about the location of works to be referred to transshipment. Another problem is narrow comprehension of organizations engaged in oil transportation as well as uncertainty of norms related to the terminology of oil transportation transshipment and reloading. All the above inaccuracies and ambiguities in legislation lead to problems in organizations engaged in oil transportation as is shown by the example of ldquoMarine Port Servicerdquo Close Corporation. The author also presents the results of analysis of judicial practice in the sphere of interpreting para. 4 subclause 2.2. clause 1 Art. 164 of the Taxation Code of the Russian Federation. The possible

  19. Lipase production by Penicillium restrictum using solid waste of industrial babassu oil production as substrate.

    Science.gov (United States)

    Palma, M B; Pinto, A L; Gombert, A K; Seitz, K H; Kivatinitz, S C; Castilho, L R; Freire, D M

    2000-01-01

    Lipase, protease, and amylase production by Penicillium restrictum in solid-state fermentation was investigated. The basal medium was an industrial waste of babassu oil (Orbignya oleifera) production. It was enriched with peptone, olive oil, and Tween-80. The supplementation positively influenced both enzyme production and fungal growth. Media enriched with Tween-80 provided the highest protease activity (8.6 U/g), whereas those enriched with peptone and olive oil led to the highest lipase (27.8 U/g) and amylase (31.8 U/g) activities, respectively.

  20. Treatment and Valorization of Palm Oil Mill Effluent through Production of Food Grade Yeast Biomass

    OpenAIRE

    Joy O. Iwuagwu; J. Obeta Ugwuanyi

    2014-01-01

    Palm oil mill effluent (POME) is high strength wastewater derived from processing of palm fruit. It is generated in large quantities in all oil palm producing nations where it is a strong pollutant amenable to microbial degradation being rich in organic carbon, nitrogen, and minerals. Valorization and treatment of POME with seven yeast isolates was studied under scalable conditions by using POME to produce value-added yeast biomass. POME was used as sole source of carbon and nitrogen and the ...

  1. KINETIC STUDIES ON BIODEGRADATION OF LIPIDS FROM OLIVE OIL MILL WASTEWATERS WITH FREE AND IMMOBILIZED Bacillus sp. CELLS

    Directory of Open Access Journals (Sweden)

    Anca-Irina Galaction

    2012-03-01

    Full Text Available The studies on the biodegradation of lipids from olive oil mill wastewater with free and immobilized Bacillus sp. cells indicated that the maximum specific rate of the process is reached at pH = 8. The use of immobilized cells allows to increasing the number of biodegradation process cycles, but reduces the rate of the process. In this case, the process rate depends on the biocatalysts size and cells concentration inside them. Thus, at bacterial cells concentration of 9 g d.w./100 mL biocatalyst, the apparent specific rate varied from 4.65 to 1.46×10-2 h-1 by increasing the biocatalyst particles diameter from 3 to 4.2 mm.The cumulated influences of the particles size and cells concentration have been included in a mathematical model for the apparent specific rate of lipids biodegradation. The model offers a good concordance with the experimental data, the average deviation being of +/- 7.38%.

  2. OIL SLUGS FOR PRODUCTION OF PISTON RING

    Directory of Open Access Journals (Sweden)

    V. F. Bevza

    2008-01-01

    Full Text Available The developed technological process of continuously cyclic casting by frosting allows to receive high-quality hollow cylindrical slugs of cast iron for production of critical parts. 

  3. Removal of boron from ceramic industry wastewater by adsorption-flocculation mechanism using palm oil mill boiler (POMB) bottom ash and polymer.

    Science.gov (United States)

    Chong, Mei Fong; Lee, Kah Peng; Chieng, Hui Jiun; Syazwani Binti Ramli, Ili Izyan

    2009-07-01

    Boron is extensively used in the ceramic industry for enhancing mechanical strength of the tiles. The discharge of boron containing wastewater to the environment causes severe pollution problems. Boron is also dangerous for human consumption and causes organisms' reproductive impediments if the safe intake level is exceeded. Current methods to remove boron include ion-exchange, membrane filtration, precipitation-coagulation, biological and chemical treatment. These methods are costly to remove boron from the wastewater and hence infeasible for industrial wastewater treatment. In the present research, adsorption-flocculation mechanism is proposed for boron removal from ceramic wastewater by using Palm Oil Mill Boiler (POMB) bottom ash and long chain polymer or flocculant. Ceramic wastewater is turbid and milky in color which contains 15 mg/L of boron and 2000 mg/L of suspended solids. The optimum operating conditions for boron adsorption on POMB bottom ash and flocculation using polymer were investigated in the present research. Adsorption isotherm of boron on bottom ash was also investigated to evaluate the adsorption capacity. Adsorption isotherm modeling was conducted based on Langmuir and Freundlich isotherms. The results show that coarse POMB bottom ash with particle size larger than 2 mm is a suitable adsorbent where boron is removed up to 80% under the optimum conditions (pH=8.0, dosage=40 g bottom ash/300 ml wastewater, residence time=1h). The results also show that KP 1200 B cationic polymer is effective in flocculating the suspended solids while AP 120 C anionic polymer is effective in flocculating the bottom ash. The combined cationic and anionic polymers are able to clarify the ceramic wastewater under the optimum conditions (dosage of KP 1200 B cationic polymer=100 mg/L, dosage of AP 120 C anionic polymer=50 mg/L, mixing speed=200 rpm). Under the optimum operating conditions, the boron and suspended solids concentration of the treated wastewater were

  4. Transesterification of coconut oil for FAME production using ultrasound

    Science.gov (United States)

    Supriadi, Eko; Marlinda, Lenny; Prajitno, Danawati Hari; Mahfud, Mahfud

    2017-05-01

    To overcome energy crisis, the vegetable oils-derived biofuel can be chosen as an alternative to petroleum-based diesel. The transesterification of coconut oil in methanol with K/γ-Al2O3 catalyst using ultrasound-assisted to produce fatty acid methyl ester (FAME) as one of type biofuel was studied. The reaction occurred in batch reactor at a 9 : 1 molar ratio of methanol to coconut oil. The following reaction conditions were used in the catalytic test : concentration of catalyst to oil of 0.5, 1.0, 1.5, 2.0, and 2.5%, the reaction time of 10, 20, 30, 60, 90, 120, and 150 s, and the frequency ultrasonication of 20 and 40 KHz. At first, the preparation of K/γ-Al2O3 catalyst was done and followed by transesterification process. After reaction, the phase separation and purification from impurities were done. Finally, FAME was analized based on this parameters, i.e., yield, density, viscosity, and flash point. FAME yield of 93.76% was obtained at the frequency ultrasonication of 40 kHz with K/γ-Al2O3 catalyst concentration to oil of 2.5 wt.% for 150 s. It's the best conditions for FAME production by transesterification of coconut oil using ultrasound-assisted.

  5. Oil product sales in 2010 - Results per product and per district

    International Nuclear Information System (INIS)

    Korman, Bernard; Lauverjat, Jean

    2011-11-01

    This document proposes tables of data corresponding to sales of different oil products (super unleaded petrol, Diesel fuel, domestic heating oil, heavy fuels) in metropolitan France in 2011, in the French districts and regions, and in the coastal districts and regions for the maritime sector (fishing activity, ships).

  6. Diverse bacteria isolated from microtherm oil-production water.

    Science.gov (United States)

    Sun, Ji-Quan; Xu, Lian; Zhang, Zhao; Li, Yan; Tang, Yue-Qin; Wu, Xiao-Lei

    2014-02-01

    In total, 435 pure bacterial strains were isolated from microtherm oil-production water from the Karamay Oilfield, Xinjiang, China, by using four media: oil-production water medium (Cai medium), oil-production water supplemented with mineral salt medium (CW medium), oil-production water supplemented with yeast extract medium (CY medium), and blood agar medium (X medium). The bacterial isolates were affiliated with 61 phylogenetic groups that belong to 32 genera in the phyla Actinobacteria, Firmicutes, and Proteobacteria. Except for the Rhizobium, Dietzia, and Pseudomonas strains that were isolated using all the four media, using different media led to the isolation of bacteria with different functions. Similarly, nonheme diiron alkane monooxygenase genes (alkB/alkM) also clustered according to the isolation medium. Among the bacterial strains, more than 24 % of the isolates could use n-hexadecane as the sole carbon source for growth. For the first time, the alkane-degrading ability and alkB/alkM were detected in Rhizobium, Rhodobacter, Trichococcus, Micrococcus, Enterococcus, and Bavariicoccus strains, and the alkM gene was detected in Firmicutes strains.

  7. Ultrasound Assisted Esterification of Rubber Seed Oil for Biodiesel Production

    Directory of Open Access Journals (Sweden)

    W Widayat

    2012-04-01

    Full Text Available Production of biodiesel is currently shifting from the first to the second generation inwhich the raw materials are mostly from non-edible type oils and fats. Biodiesel production iscommonly conducted under batch operation using mechanical agitation to accelerate masstransfers. The main drawback of oil esterification is the high content of free fatty acids (FFA whichmay reduce the yield of biodiesel and prolong the production time (2-5 hours. Ultrasonificationhas been used in many applications such as component extraction due to its ability to producecavitation under certain frequency. This research is aimed to facilitate ultrasound system forimproving biodiesel production process particularly rubber seed oil. An ultrasound unit was usedunder constant temperature (40oC and frequency of 40 Hz. The result showed that ultrasound canreduces the processing time and increases the biodiesel yield significantly. A model to describecorrelation of yield and its independent variables is yield (Y = 43,4894 – 0,6926 X1 + 1,1807 X2 –7,1042 X3 + 2,6451 X1X2 – 1,6557 X1X3 + 5,7586 X2X3 - 10,5145 X1X2X3, where X1 is mesh sizes, X2ratio oil: methanol and X3 type of catalyst.

  8. Radiation methods for demercaptanization and desulfurization of oil products

    International Nuclear Information System (INIS)

    Zaykina, R.F.; Zaykin, Yu.A.; Mamonova, T.B.; Nadirov, N.K.

    2002-01-01

    A two-stage method for the desulfurization of oil is presented. The first stage strongly oxidizes sulfuric material to do away with its chemical aggressiveness and promote its removal. Desulfurization of the overall product is reached at the second stage by means of conventional methods

  9. Radiation methods for demercaptanization and desulfurization of oil products

    Science.gov (United States)

    Zaykina, R. F.; Zaykin, Yu. A.; Mamonova, T. B.; Nadirov, N. K.

    2002-03-01

    A two-stage method for the desulfurization of oil is presented. The first stage strongly oxidizes sulfuric material to do away with its chemical aggressiveness and promote its removal. Desulfurization of the overall product is reached at the second stage by means of conventional methods.

  10. Moringa oleifera oil: Studies of characterization and biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    da Silva, Jhosianna P.V.; Serra, Tatiana M.; Meneghetti, Simoni M.P. [Universidade Federal de Alagoas, Instituto de Quimica e Biotecnologia, Laboratorio de Oleoquimica, Maceio, Alagoas, CEP 57072-970 (Brazil); Gossmann, Marcelo; Wolf, Carlos R.; Meneghetti, Mario R. [Universidade Luterana do Brasil, Instituto de Quimica, Canoas, Rio Grande do Sul, CEP 92420-280 (Brazil)

    2010-10-15

    This work describes studies with the seeds of Moringa oleifera (MO), obtained in the northeast of Brazil, evaluating some properties and chemical composition of the oil, as well any potential application in biodiesel production. The studied physicochemical properties of the MO biodiesel, suggest that this material may be used as fuel in diesel engines, mainly as a mixture to petrodiesel. (author)

  11. Physical Properties And Maize Production In A Spent Oil ...

    African Journals Online (AJOL)

    Information on the use of plant species and organic nutrients to improve the physical properties of oil-contaminated soil, with a view to making it conducive for crop production, is very important. Three legumes (Gliricidia sepium, Leucenae leucocephala and Calapogonium caeruleam) combined or not with poultry manure ...

  12. Develop a New Lesquerella fendleri Crop for Castor Oil Production

    Science.gov (United States)

    Seed oil of Lesquerella fendleri contains a valuable hydroxy fatty acid (HFA), lesquerolic acid (20:1OH). The conventional source of HFA is ricinoleic acid (18:1OH) from castor seeds. Ricinoleic acid and its derivatives are used as raw materials for numerous industrial products, such as lubricants, ...

  13. Biological sludge solubilisation for reduction of excess sludge production in wastewater treatment process.

    Science.gov (United States)

    Yamaguchi, T; Yao, Y; Kihara, Y

    2006-01-01

    A novel sludge disintegration system (JFE-SD system) was developed for the reduction of excess sludge production in wastewater treatment plants. Chemical and biological treatments were applied to disintegrate excess sludge. At the first step, to enhance biological disintegration, the sludge was pretreated with alkali. At the second step, the sludge was disintegrated by biological treatment. Many kinds of sludge degrading microorganisms integrated the sludge. The efficiency of the new sludge disintegration system was confirmed in a full-scale experiment. The JFE-SD system reduced excess sludge production by approximately 50% during the experimental period. The quality of effluent was kept at quite a good level. Economic analysis revealed that this system could significantly decrease the excess sludge treatment cost.

  14. Two phases fermentative process for hydrogen and methane production from cassava wastewater

    Directory of Open Access Journals (Sweden)

    Aryane Mota Oliveira

    2017-04-01

    Full Text Available Introduction: Hydrogen and methane production was investigated in two phases of fermentative process. Objective: At the acidogenic phase, an anaerobic fluidized bed reactor was fed with cassava wastewater producing hydrogen. Methods: Expanded clay was used as a support material for biomass immobilization. The reactor was operated with HRT ranging from 8-1 h. Results: The best hydrogen yield production was 1.91 mol H2/mol glucose at HRT of 2 h. At the methanogenic phase, the acidogenic process effluent fed a fixed-bed reactor producing methane. Conclusion: Sururu (Mytella falcata shells was used as support acted as pH neutralizer in the fixed-bed reactor, yielding best (0.430±0.150 Lmethane/gCOD with 12h HRT phase.

  15. Development of hydrate risk quantification in oil and gas production

    Science.gov (United States)

    Chaudhari, Piyush N.

    Subsea flowlines that transport hydrocarbons from wellhead to the processing facility face issues from solid deposits such as hydrates, waxes, asphaltenes, etc. The solid deposits not only affect the production but also pose a safety concern; thus, flow assurance is significantly important in designing and operating subsea oil and gas production. In most subsea oil and gas operations, gas hydrates form at high pressure and low temperature conditions, causing the risk of plugging flowlines, with a undesirable impact on production. Over the years, the oil and gas industry has shifted their perspective from hydrate avoidance to hydrate management given several parameters such as production facility, production chemistry, economic and environmental concerns. Thus, understanding the level of hydrate risk associated with subsea flowlines is an important in developing efficient hydrate management techniques. In the past, hydrate formation models were developed for various flow-systems (e.g., oil dominated, water dominated, and gas dominated) present in the oil and gas production. The objective of this research is to extend the application of the present hydrate prediction models for assessing the hydrate risk associated with subsea flowlines that are prone to hydrate formation. It involves a novel approach for developing quantitative hydrate risk models based on the conceptual models built from the qualitative knowledge obtained from experimental studies. A comprehensive hydrate risk model, that ranks the hydrate risk associated with the subsea production system as a function of time, hydrates, and several other parameters, which account for inertial, viscous, interfacial forces acting on the flow-system, is developed for oil dominated and condensate systems. The hydrate plugging risk for water dominated systems is successfully modeled using The Colorado School of Mines Hydrate Flow Assurance Tool (CSMHyFAST). It is found that CSMHyFAST can be used as a screening tool in

  16. A cost analysis of microalgal biomass and biodiesel production in open raceways treating municipal wastewater and under optimum light wavelength.

    Science.gov (United States)

    Kang, Zion; Kim, Byung-Hyuk; Ramanan, Rishiram; Choi, Jong-Eun; Yang, Ji-Won; Oh, Hee-Mock; Kim, Hee-Sik

    2015-01-01

    Open raceway ponds are cost-efficient for mass cultivation of microalgae compared with photobioreactors. Although low-cost options like wastewater as nutrient source is studied to overcome the commercialization threshold for biodiesel production from microalgae, a cost analysis on the use of wastewater and other incremental increases in productivity has not been elucidated. We determined the effect of using wastewater and wavelength filters on microalgal productivity. Experimental results were then fitted into a model, and cost analysis was performed in comparison with control raceways. Three different microalgal strains, Chlorella vulgaris AG10032, Chlorella sp. JK2, and Scenedesmus sp. JK10, were tested for nutrient removal under different light wavelengths (blue, green, red, and white) using filters in batch cultivation. Blue wavelength showed an average of 27% higher nutrient removal and at least 42% higher chemical oxygen demand removal compared with white light. Naturally, the specific growth rate of microalgae cultivated under blue wavelength was on average 10.8% higher than white wavelength. Similarly, lipid productivity was highest in blue wavelength, at least 46.8% higher than white wavelength, whereas FAME composition revealed a mild increase in oleic and palmitic acid levels. Cost analysis reveals that raceways treating wastewater and using monochromatic wavelength would decrease costs from 2.71 to 0.73 $/kg biomass. We prove that increasing both biomass and lipid productivity is possible through cost-effective approaches, thereby accelerating the commercialization of low-value products from microalgae, like biodiesel.

  17. Photolysis of the antidepressants amisulpride and desipramine in wastewaters: Identification of transformation products formed and their fate

    International Nuclear Information System (INIS)

    Gros, Meritxell; Williams, Mike; Llorca, Marta; Rodriguez-Mozaz, Sara; Barceló, Damià; Kookana, Rai S.

    2015-01-01

    Attenuation of pharmaceuticals due to natural sunlight is expected to be an important removal pathway in wastewater treatment plants using treatment lagoon systems. In this work, the photolysis of two antidepressants, amisulpride and desipramine, has been investigated in both ultrapure water and wastewater under simulated solar irradiation. Results showed that for amisulpride short irradiation times (t 1/2 approximately 3 h in pure water and 4 h in wastewater) were adequate to degrade the parent compound while a longer exposure period was required for desipramine (t 1/2 of approximately 36 h in pure water), although its degradation is enhanced almost three times by indirect photolysis in wastewaters. A significant number of transformation products (TPs) were identified for both pharmaceuticals by high-resolution mass spectrometry. In general, TPs formed are not persistent although acute toxicity tests for desipramine and its TPs showed an increase of the mixture toxicity after solar irradiation, suggesting that some TPs may be more toxic than the parent compound. In wastewaters collected from treatment lagoons, only amisulpride and one of its major TPs, TP 357, were detected. This indicates that long solar exposure times may be necessary for an effective elimination of these substances in lagoon systems or that photolysis may not be the main removal pathway for these particular compounds. - Highlights: • Photolysis of both compounds resulted in several transformation products, some of which were previously unknown. • Short irradiation times may be adequate to degrade amisulpride whereas a longer exposure is required for desipramine. • Transformation of desipramine was enhanced by about three times due to indirect photolysis in wastewaters. • For desipramine, mixture acute toxicity increased after solar irradiation. • Photolysis is unlikely to be the main removal pathway for the two antidepressants during wastewater treatment

  18. Photolysis of the antidepressants amisulpride and desipramine in wastewaters: Identification of transformation products formed and their fate

    Energy Technology Data Exchange (ETDEWEB)

    Gros, Meritxell [Commonwealth Scientific and Industrial Research Organization (CSIRO), Land and Water Flagship, Waite Campus, Urrbrae, 5064 Adelaide, SA (Australia); Swedish University of Agricultural Sciences (SLU), Department of Aquatic Sciences and Assessment, Lennart Hjelms väg 9, 75007 Uppsala (Sweden); Williams, Mike, E-mail: Mike.Williams@csiro.au [Commonwealth Scientific and Industrial Research Organization (CSIRO), Land and Water Flagship, Waite Campus, Urrbrae, 5064 Adelaide, SA (Australia); Llorca, Marta; Rodriguez-Mozaz, Sara [Catalan Institute for Water Research (ICRA), Scientific and Technological Park of the University of Girona, C/Emili Grahit, 101 Girona (Spain); Barceló, Damià [Catalan Institute for Water Research (ICRA), Scientific and Technological Park of the University of Girona, C/Emili Grahit, 101 Girona (Spain); Water and Soil Quality Research Group, Department of Environmental IDAEA-CSIC, Jordi Girona 18-26, E-08034 Barcelona (Spain); Kookana, Rai S. [Commonwealth Scientific and Industrial Research Organization (CSIRO), Land and Water Flagship, Waite Campus, Urrbrae, 5064 Adelaide, SA (Australia)

    2015-10-15

    Attenuation of pharmaceuticals due to natural sunlight is expected to be an important removal pathway in wastewater treatment plants using treatment lagoon systems. In this work, the photolysis of two antidepressants, amisulpride and desipramine, has been investigated in both ultrapure water and wastewater under simulated solar irradiation. Results showed that for amisulpride short irradiation times (t{sub 1/2} approximately 3 h in pure water and 4 h in wastewater) were adequate to degrade the parent compound while a longer exposure period was required for desipramine (t{sub 1/2} of approximately 36 h in pure water), although its degradation is enhanced almost three times by indirect photolysis in wastewaters. A significant number of transformation products (TPs) were identified for both pharmaceuticals by high-resolution mass spectrometry. In general, TPs formed are not persistent although acute toxicity tests for desipramine and its TPs showed an increase of the mixture toxicity after solar irradiation, suggesting that some TPs may be more toxic than the parent compound. In wastewaters collected from treatment lagoons, only amisulpride and one of its major TPs, TP 357, were detected. This indicates that long solar exposure times may be necessary for an effective elimination of these substances in lagoon systems or that photolysis may not be the main removal pathway for these particular compounds. - Highlights: • Photolysis of both compounds resulted in several transformation products, some of which were previously unknown. • Short irradiation times may be adequate to degrade amisulpride whereas a longer exposure is required for desipramine. • Transformation of desipramine was enhanced by about three times due to indirect photolysis in wastewaters. • For desipramine, mixture acute toxicity increased after solar irradiation. • Photolysis is unlikely to be the main removal pathway for the two antidepressants during wastewater treatment.

  19. Comparing the dynamic performance of wastewater treatment systems: A metafrontier Malmquist productivity index approach.

    Science.gov (United States)

    Molinos-Senante, María; Hernández-Sancho, Francesc; Sala-Garrido, Ramón

    2015-09-15

    The assessment of productivity change of wastewater treatment plants (WWTPs) is essential to improve the performance over time of the facilities evaluated. This study assessed and compared the productivity growth of WWTPs operating with non-homogeneous technologies. The metafrontier Malmquist productivity index (MMPI) was computed for a sample of 99 WWTPs encompassing 4 alternative technologies: activated sludge (AS), aerated lagoon (AL), trickling filter (TF) and rotating biological contactor (BD). The results indicated that, on average, WWTPs with AS and BD exhibited better performance over time than WWTPs with AL and TF. The MMPI indicates that, over the period 2007-2009, the productivity rose by 0.9% and 0.3% for AS and BD technologies, respectively, whilst for the AL and TF processes, the productivity decreased by 0.5% and 2.2%, respectively. The decomposition of the MMPI into efficiency change (EC) and technical change (TC) illustrated that EC was a positive driver of productivity change for WWTPs that use AS, whilst TC contributed positively to the productivity growth of WWTPs using AL and BD. Several policy implications to help managers make informed decisions were drawn from our empirical analysis. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Dual purpose microalgae-bacteria-based systems that treat wastewater and produce biodiesel and chemical products within a biorefinery.

    Science.gov (United States)

    Olguín, Eugenia J

    2012-01-01

    Excess greenhouse gas emissions and the concomitant effect on global warming have become significant environmental, social and economic threats. In this context, the development of renewable, carbon-neutral and economically feasible biofuels is a driving force for innovation worldwide. A lot of effort has been put into developing biodiesel from microalgae. However, there are still a number of technological, market and policy barriers that are serious obstacles to the economic feasibility and competitiveness of such biofuels. Conversely, there are also a number of business opportunities if the production of such alternative biofuel becomes part of a larger integrated system following the Biorefinery strategy. In this case, other biofuels and chemical products of high added value are produced, contributing to an overall enhancement of the economic viability of the whole integrated system. Additionally, dual purpose microalgae-bacteria-based systems for treating wastewater and production of biofuels and chemical products significantly contribute to a substantial saving in the overall cost of microalgae biomass production. These types of systems could help to improve the competitiveness of biodiesel production from microalgae, according to some recent Life Cycle Analysis studies. Furthermore, they do not compete for fresh water resources for agricultural purposes and add value to treating the wastewater itself. This work reviews the most recent and relevant information about these types of dual purpose systems. Several aspects related to the treatment of municipal and animal wastewater with simultaneous recovery of microalgae with potential for biodiesel production are discussed. The use of pre-treated waste or anaerobic effluents from digested waste as nutrient additives for weak wastewater is reviewed. Isolation and screening of microalgae/cyanobacteria or their consortia from various wastewater streams, and studies related to population dynamics in mixed cultures

  1. Biodiesel Production from Waste Cooking Oil Using Hydrodinamic Cavitation

    OpenAIRE

    Muhammad Supardan; Satriana Satriana; Mahlinda Mahlinda

    2013-01-01

    The aim of this research was to study biodiesel production from low cost feedstock of waste cooking oil (WCO) using hydrodynamic cavitation apparatus. A two-step processes esterification process and transesterification process using hydrodynamic cavitation for the production of biodiesel from WCO is presented. The first step is acid-catalyzed esteri-fication process for reducing free fatty acid (FFA) content of WCO and followed by base-catalyzed transesterification process for converting WCO ...

  2. Asphaltene precipitates in oil production wells

    DEFF Research Database (Denmark)

    Kleinitz, W,; Andersen, Simon Ivar

    1998-01-01

    compounds in the organic scales from operations definitely differed from the data published in the literature. In order to dissolve the precipitates and thus eliminate the damage, various organic solvents and industrial solvent mixtures were examined. The kinetics of the dissolution process in operational...... production is also explained and discussed in detail from a reservoir engineering standpoint....

  3. Improved Laccase Production by Trametes pubescens MB89 in Distillery Wastewaters

    Directory of Open Access Journals (Sweden)

    P. J. Strong

    2011-01-01

    Full Text Available Various culture parameters were optimised for laccase synthesis by Trametes pubescens MB89, including pH, carbon source, nitrogen source, lignocellulosic supplements, and reported inducers. Glucose, in conjunction with a complex nitrogen source at pH 5.0, resulted in the highest laccase yield. Adding ethanol, copper, or 2,5-xylidine prior to inoculation further improved laccase concentrations. The addition of 2,5-xylidine was further investigated with multiple additions applied at varying times. This novel application substantially improved laccase production when applied regularly from inoculation and during the growth phase, and also countered glucose repression of laccase synthesis. Single and multiple factor changes were studied in three distillery wastewaters and a wine lees. A synergistic increase in laccase synthesis was observed with the addition of glucose, copper, and 2,5-xylidine. Single addition of 2,5-xylidine proved most beneficial with distillery wastewaters, while copper addition was most beneficial when using the wine lees as a culture medium.

  4. Pharmaceuticals and Personal Care Products in Municipal Wastewater and the Marine Receiving Environment Near Victoria Canada

    Directory of Open Access Journals (Sweden)

    Jeremy Krogh

    2017-12-01

    Full Text Available Concerns over the fate of pharmaceuticals and personal care products (PPCP within the environment have been growing with the advent of more precise analytical methods. The discharge of municipal wastewater has been identified as a significant source of these contaminants, particularly where wastewater treatment is minimal. Here we present results from a comprehensive monitoring regime located around Victoria, BC, Canada. Samples were collected between 2009 and 2016 from a variety of sources including marine water, sediment and biota adjacent to two major untreated sewage outfalls, as well as the sewage itself. PPCP concentrations within the untreated sewage were high, and the sediment surrounding the outfalls showed corresponding contamination. However, this contamination dropped quickly with distance from the outfall such that by 800 m distance most PPCPs were below detection limits. Tissue samples of resident Northern Horse mussels (Modiolus modiolus collected adjacent to one of the major sewage outfalls showed high single sample concentrations of the antimicrobial triclosan (317 ng g−1 dry weight, the antibiotic ciprofloxacin (176 ng g−1 dry weight, as well as the antidepressant sertraline (84.1 ng g−1 dry weight. Reference stations from around the region showed very low concentrations of contamination with almost all PPCP concentrations being below detection limits. Within the sewage, concentrations were largely stable overtime, with the exception of triclosan and triclocarban which both showed declines over the study period.

  5. Potential for methane production from anaerobic co-digestion of swine manure with winery wastewater.

    Science.gov (United States)

    Riaño, B; Molinuevo, B; García-González, M C

    2011-03-01

    This work examines the methane production potential for the anaerobic co-digestion of swine manure (SM) with winery wastewater (WW). Batch and semi-continuous experiments were carried out under mesophilic conditions. Batch experiments revealed that the highest specific methane yield was 348 mL CH(4)g(-1) COD added, obtained at 85.4% of WW and 0.7 g COD g(-1)VS. Specific methane yield from SM alone was 27 mL CH(4)g(-1) COD added d(-1). Furthermore, specific methane yields were 49, 87 and 107 mL CH(4)g(-1) COD added d(-1) for the reactors co-digesting mixtures with 10% WW, 25% WW and 40% WW, respectively. Co-digestion with 40% WW improved the removal efficiencies up to 52% (TCOD), 132% (SCOD) and 61% (VSS) compared to SM alone. These results suggest that methane can be produced very efficiently by the co-digestion of swine manure with winery wastewater. Copyright © 2011 Elsevier Ltd. All rights reserved.

  6. Biodiesel production using oil from fish canning industry wastes

    International Nuclear Information System (INIS)

    Costa, J.F.; Almeida, M.F.; Alvim-Ferraz, M.C.M.; Dias, J.M.

    2013-01-01

    Highlights: • A process was established to produce biodiesel from fish canning industry wastes. • Biodiesel production was enabled by an acid esterification pre-treatment. • Optimization studies showed that the best catalyst concentration was 1 wt.% H 2 SO 4 . • There was no advantage when a two-step alkali transesterification was employed. • Waste oil from olive oil bagasse could be used to improve fuel quality. - Abstract: The present study evaluated biodiesel production using oil extracted from fish canning industry wastes, focusing on pre-treatment and reaction conditions. Experimental planning was conducted to evaluate the influence of acid catalyst concentration (1–3 wt.% H 2 SO 4 ) in the esterification pre-treatment and the amount of methanolic solution (60–90 vol.%) used at the beginning of the further two-step alkali transesterification reaction. The use of a raw-material mixture, including waste oil obtained from olive oil bagasse, was also studied. The results from experimental planning showed that catalyst concentration mostly influenced product yield and quality, the best conditions being 1 wt.% catalyst and 60 vol.% of methanolic solution, to obtain a product yield of 73.9 wt.% and a product purity of 75.5 wt.%. Results from a one-step reaction under the selected conditions showed no advantage of performing a two-step alkali process. Although under the best conditions several of the biodiesel quality parameters were in agreement with standard specifications, a great variation was found in the biodiesel acid value, and oxidation stability and methyl ester content did not comply with biodiesel quality standards. Aiming to improve fuel quality, a mixture containing 80% waste olive oil and 20% of waste fish oil was evaluated. Using such mixture, biodiesel purity increased around 15%, being close to the standard requirements (96.5 wt.%), and the oxidation stability was in agreement with the biodiesel quality standard values (⩾6 h), which

  7. Biofilm Attached Cultivation of Chlorella pyrenoidosa Is a Developed System for Swine Wastewater Treatment and Lipid Production

    Directory of Open Access Journals (Sweden)

    Pengfei Cheng

    2017-09-01

    Full Text Available This study showed the new potential of using soluble contents and heavy metals in swine wastewater as nutrient supplements for the algae Chlorella pyrenoidosa with biofilm attached method. Algae with biofilm attached cultivation grew well in unpasteurized wastewater reaching a biomass productivity of 5.03 g m−2 d−1, lipid content of 35.9% and lipid productivity of 1.80 g m−2 d−1. Chlorella grew in BG11 medium delivered lower values for each of the aforementioned parameters. The FAMEs compositions in the algae paste were mainly consisted of C16:0, C18:2, and C18:3. Algae removed NH4+–N, total phosphorus (TP, and COD by 75.9, 68.4, and 74.8%, respectively. Notably, Zn2+, Cu+, and Fe2+ were removed from wastewater with a ratio of 65.71, 53.64, and 58.89%, respectively. Biofilm attached cultivation of C. pyrenoidosa in swine wastewater containing heavy metals could accumulate considerable biomass and lipid, and the removal ratio of NH4+–N, TP, COD, and as well as heavy metal were high. Treatment of wastewater with biofilm attached cultivation showed an increasingly popular for the concentration of microalgae and environmental sustainability.

  8. Biofilm Attached Cultivation of Chlorella pyrenoidosa Is a Developed System for Swine Wastewater Treatment and Lipid Production

    Science.gov (United States)

    Cheng, Pengfei; Wang, Yuanzhu; Liu, Tianzhong; Liu, Defu

    2017-01-01

    This study showed the new potential of using soluble contents and heavy metals in swine wastewater as nutrient supplements for the algae Chlorella pyrenoidosa with biofilm attached method. Algae with biofilm attached cultivation grew well in unpasteurized wastewater reaching a biomass productivity of 5.03 g m−2 d−1, lipid content of 35.9% and lipid productivity of 1.80 g m−2 d−1. Chlorella grew in BG11 medium delivered lower values for each of the aforementioned parameters. The FAMEs compositions in the algae paste were mainly consisted of C16:0, C18:2, and C18:3. Algae removed NH4+–N, total phosphorus (TP), and COD by 75.9, 68.4, and 74.8%, respectively. Notably, Zn2+, Cu+, and Fe2+ were removed from wastewater with a ratio of 65.71, 53.64, and 58.89%, respectively. Biofilm attached cultivation of C. pyrenoidosa in swine wastewater containing heavy metals could accumulate considerable biomass and lipid, and the removal ratio of NH4+–N, TP, COD, and as well as heavy metal were high. Treatment of wastewater with biofilm attached cultivation showed an increasingly popular for the concentration of microalgae and environmental sustainability. PMID:28983302

  9. Phytoremediation of kitchen wastewater by Spirulina platensis (Nordstedt Geiteler: pigment content, production variable cost and nutritional value

    Directory of Open Access Journals (Sweden)

    Siripen Traichaiyaporn1

    2008-01-01

    Full Text Available Phytoremediation of domestic wastewater by Spirulina platensis was carried out using kitchen wastewater. A complete randomised design (CRD was created for the experiment which was performed on modified Zarrouk’s medium (Zm, 100% kitchen wastewater (100%Kw and 90% kitchen wastewater (90%Kw. Water quality, biomass production, pigment content and nutritional value of Spirulina platensis were determined from cultures harvested every 5 days for a period of 15 days. The physico-chemical properties of cultivated wastewater were: water temperature 27-28 oC, pH 8.73-9.77 and DO 0.20-7.20 mg L-1. The 100%Kw and 90%Kw produced lower BOD, COD, TP, NH3-N, ON, TKN, NO3-N, NO2-N, TON and TN compared to Zm with p< 0.05. After cultivation, the treated kitchen wastewater met the standards for safe discharge in Thailand. The highest level of -carotene of S. platensis was achieved in Zm (0.29 mg g-1 and 100%Kw (0.29 mg g – 1 while the highest levels of C-phycocyanin were obtained in 100%Kw (17.95 mg g -1 and 90%Kw (16.31 mg g-1. The highest production variable cost for dry weight of S. platensis was in Zm (310.6 Baht kg -1 and 90%Kw (303.6 Baht kg -1 as compared to 100%Kw (276.6 Baht kg -1, with p<0.05. The highest biomass production of S. platensis was achieved in Zm (0.84 g L-1 and 100%Kw (0.82 g L-1, with protein content of 54.44% and 35.86%, respectively. Implications for the use of S. platensis for phytoremediation and C-phycocyanin production using of 100%Kw and 90% Kw are discussed.

  10. Worldwide cheap and heavy oil productions: A long-term energy model

    International Nuclear Information System (INIS)

    Guseo, Renato

    2011-01-01

    Crude oil, natural gas liquids, heavy oils, deepwater oils, and polar oils are non-renewable energy resources with increasing extraction costs. Two major definitions emerge: regular or 'cheap' oil and non-conventional or 'heavy' oil. Peaking time in conventional oil production has been a recent focus of debate. For two decades, non-conventional oils have been mixed with regular crude oil. Peaking time estimation and the rate at which production may be expected to decline, following the peak, are more difficult to determine. We propose a two-wave model for world oil production pattern and forecasting, based on the diffusion of innovation theories: a sequential multi-Bass model. Historical well-known shocks are confirmed, and new peaking times for crude oil and mixed oil are determined with corresponding depletion rates. In the final section, possible ties between the dynamics of oil extraction and refining capacities are discussed as a predictive symptom of an imminent mixed oil peak in 2016. - Highlights: → Production of conventional and non-conventional oils in aggregate time series. → Decomposition modelling and forecasting with a multi-regime model. → Diffusion of innovation theories and appropriateness of applying Bass concepts to the extraction of oil resources. → Partially overlapping oil extraction processes. → Refining capacities and dynamics of oil extraction.

  11. Olive Oil Based Emulsions in Frozen Puff Pastry Production

    Science.gov (United States)

    Gabriele, D.; Migliori, M.; Lupi, F. R.; de Cindio, B.

    2008-07-01

    Puff pastry is an interesting food product having different industrial applications. It is obtained by laminating layers of dough and fats, mainly shortenings or margarine, having specific properties which provides required spreading characteristic and able to retain moisture into dough. To obtain these characteristics, pastry shortenings are usually saturated fats, however the current trend in food industry is mainly oriented towards unsatured fats such as olive oil, which are thought to be safer for human health. In the present work, a new product, based on olive oil, was studied as shortening replacer in puff pastry production. To ensure the desired consistency, for the rheological matching between fat and dough, a water-in-oil emulsion was produced based on olive oil, emulsifier and a hydrophilic thickener agent able to increase material structure. Obtained materials were characterized by rheological dynamic tests in linear viscoelastic conditions, aiming to setup process and material consistency, and rheological data were analyzed by using the weak gel model. Results obtained for tested emulsions were compared to theological properties of a commercial margarine, adopted as reference value for texture and stability. Obtained emulsions are characterized by interesting rheological properties strongly dependent on emulsifier characteristics and water phase composition. However a change in process temperature during fat extrusion and dough lamination seems to be necessary to match properly typical dough rheological properties.

  12. Ultrasound Assisted Esterification of Rubber Seed Oil for Biodiesel Production

    Directory of Open Access Journals (Sweden)

    Berkah Fajar Tamtomo Kiono

    2012-02-01

    Full Text Available roduction of biodiesel is currently shifting from the first to the second generation in which the raw materials are mostly from non-edible type oils and fats. Biodiesel production is commonly conducted under batch operation using mechanical agitation to accelerate mass transfers. The main drawback of oil esterification is the high content of free fatty acids (FFA which may reduce the yield of biodiesel and prolong the production time (2-5 hours. Ultrasonification has been used in many applications such as component extraction due to its ability to produce cavitation under certain frequency. This research is aimed to facilitate ultrasound system for improving biodiesel production process particularly rubber seed oil. An ultrasound unit was used under constant temperature (40oC and frequency of 40 Hz. The result showed that ultrasound can reduces the processing time and increases the biodiesel yield significantly. A model to describe correlation of yield and its independent variables is yield (Y = 43,4894 – 0,6926 X1 + 1,1807 X2 – 7,1042 X3 + 2,6451 X1X2 – 1,6557 X1X3 + 5,7586 X2X3 - 10,5145 X1X2X3, where X1 is mesh sizes, X2 ratio oil: methanol and X3 type of catalyst.

  13. Bio ethanol production from oil palm empty fruit bunches

    International Nuclear Information System (INIS)

    Loh Soh Kheang; Muhammad Asyraf Kasim; Nasrin Abu Bakar

    2010-01-01

    Full text: The oil palm industry has an abundance of oil palm biomass. The type of biomass generated includes empty fruit bunches (EFB), oil palm trunk (OPT), kernel, shell and fronds. Generally, ligno celluloses biomass derived from oil palm has great potential to be converted into various forms of renewable energy. In this study, EFB in pulverized form was used as a feedstock for bio ethanol production. EFB contains lignin, hemicelluloses and cellulose which can be converted into fermentable sugar and bio ethanol. The EFB was initially pre-treated with 1% NaOH followed by acid hydrolysis with 0.7% sulfuric acid and enzyme prior to fermentation process with Saccharomyces cerevisea. The various process parameters for bio ethanol production was optimized i.e. pH, temperature, rate of agitation and initial feedstock concentration. The fermentation of EFB hydrolysate was at pH 4, 30 degree Celsius and 100 rpm within 72 hours of incubation yielded 10.48 g/L of bio ethanol from 50 g/L of EFB. The bio ethanol production in a 6-L bioreactor showed 36% conversion of fermentable sugar from EFB into bio ethanol. (author)

  14. OPEC and non-OPEC oil production and the global economy

    OpenAIRE

    Ratti, Ronald A.; Vespignani, Joaquin L.

    2014-01-01

    Hamilton identifies 1973 to 1996 as “the age of OPEC” and 1997 to the present as “a new industrial age.” During 1974-1996 growth in non-OPEC oil production Granger causes growth in OPEC oil production. OPEC oil production decreases significantly with positive shocks to non-OPEC oil production in the earlier period, but does not do so in the “new industrial age”. In the “new industrial age” OPEC oil production rises significantly with an increase in oil prices, unlike during “the age of OPEC” ...

  15. Critical assessment of anaerobic processes for continuous biohydrogen production from organic wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Show, Kuan-Yeow [Faculty of Engineering and Green Technology, University Tunku Abdul Rahman, Jalan University, Bandar Barat, 31900 Kampar, Perak (Malaysia); Zhang, Zhen-Peng [Beijing Enterprises Water Group Limited, BLK 25, No. 3 Minzhuang Road, Beijing 100195 (China); Tay, Joo-Hwa [School of Civil and Environmental Engineering, Nanyang Technological University, Nanyang Avenue (Singapore); Liang, David Tee [Institute of Environmental Science and Engineering, Nanyang Technological University (Singapore); Lee, Duu-Jong [Department of Chemical Engineering, National Taiwan University, Taipei (China); Ren, Nanqi; Wang, Aijie [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China)

    2010-12-15

    Production of biohydrogen using dark fermentation has received much attention owing to the fact that hydrogen can be generated from renewable organics including waste materials. The key to successful application of anaerobic fermentation is to uncouple the liquid retention time and the biomass retention time in the reactor system. Various reactor designs based on biomass retention within the reactor system have been developed. This paper presents our research work on bioreactor designs and operation for biohydrogen production. Comparisons between immobilized-cell systems and suspended-cell systems based on biomass growth in the forms of granule, biofilm and flocs were made. Reactor configurations including column- and tank-based reactors were also assessed. Experimental results indicated that formation of granules or biofilms substantially enhanced biomass retention which was found to be proportional to the hydrogen production rate. Rapid hydrogen-producing culture growth and high organic loading rate might limit the application of biofilm biohydrogen production, since excessive growth of fermentative biomass would result in washout of support carrier. It follows that column-based granular sludge process is a preferred choice of process for continuous biohydrogen production from organic wastewater, indicating maximum hydrogen yield of 1.7 mol-H{sub 2}/mol-glucose and hydrogen production rate of 6.8 L-H{sub 2}/L-reactor h. (author)

  16. Effect of the chlortetracycline addition method on methane production from the anaerobic digestion of swine wastewater.

    Science.gov (United States)

    Huang, Lu; Wen, Xin; Wang, Yan; Zou, Yongde; Ma, Baohua; Liao, Xindi; Liang, Juanboo; Wu, Yinbao

    2014-10-01

    Effects of antibiotic residues on methane production in anaerobic digestion are commonly studied using the following two antibiotic addition methods: (1) adding manure from animals that consume a diet containing antibiotics, and (2) adding antibiotic-free animal manure spiked with antibiotics. This study used chlortetracycline (CTC) as a model antibiotic to examine the effects of the antibiotic addition method on methane production in anaerobic digestion under two different swine wastewater concentrations (0.55 and 0.22mg CTC/g dry manure). The results showed that CTC degradation rate in which manure was directly added at 0.55mg CTC/g (HSPIKE treatment) was lower than the control values and the rest of the treatment groups. Methane production from the HSPIKE treatment was reduced (pdigesters, and the total nitrogen of the 0.55mg CTC/kg manure collected from mediated swine was significantly higher than the other values. Therefore, different methane production under different antibiotic addition methods might be explained by the microbial activity and the concentrations of antibiotic intermediate products and metabolites. Because the primary entry route of veterinary antibiotics into an anaerobic digester is by contaminated animal manure, the most appropriate method for studying antibiotic residue effects on methane production may be using manure from animals that are given a particular antibiotic, rather than adding the antibiotic directly to the anaerobic digester. Copyright © 2014. Published by Elsevier B.V.

  17. Strategies to Reduce Water Footprint in Palm Oil Production: A Case of PTP Mitra Ogan, Baturaja, South Sumatra

    Directory of Open Access Journals (Sweden)

    Dara Kospa Herda Sabriyah

    2017-01-01

    Full Text Available The massive expansion of palm oil industry in Indonesia has triggered environmental issues including water-related problems which have become an important concern. Regarding the issues, sustainable practice standard has been set up as a requirement for palm oil to enter global market. Inevitably, water consumption in this sector is very crucial to be analyzed. One of the methods that can be used as a tool for sustainable appropriation of fresh water resources is water footprint analysis. The primary aim of this study was to formulate the strategies to reduce the water footprint in the palm oil production based on the best practice criteria. Both quantitative and qualitative research was conducted to get the value blue water (volume of surface or groundwater evaporated and grey water (dilution volume to dilute pollutants according to agreed water quality standards. The values of water footprint in palm oil production obtained were used to represent the existing water use and were utilized as the basis for formulating strategies in reducing water use in the palm oil milling processes which was compared with the best practice criteria. The result showed that the blue water of CPO was 109.6 m3/ton and the grey water was 537.7 m3/ton, while the blue water of palm kernel was 62,4 m3/ton and grey water was 306,2 m3/ton. The value indicated that there was an inefficient use of water in the production of palm oil. The use of steam accumulator has been proposed to reduce the use of blue water by optimizing the steam supply. Besides, the reuse of water from fat-pit pond for pressing purposes, or recovery of condensate water as dilution water in the press unit which will affect the amount of wastewater discharged can be done as the strategies in reducing both blue and grey water, as well as reuse of cooling water turbines.

  18. Techno-economical efficiency and productivity change of wastewater treatment plants: the role of internal and external factors.

    Science.gov (United States)

    Hernández-Sancho, F; Molinos-Senante, M; Sala-Garrido, R

    2011-12-01

    Efficiency and productivity are important measures for identifying best practice in businesses and optimising resource-use. This study analyses how these two measures change across the period 2003-2008 for 196 wastewater treatment plants (WWTPs) in Spain, by using the benchmarking methods of Data Envelopment Analysis and the Malmquist Productivity Index. To identify which variables contribute to the sustainability of the WWTPs, differences in efficiency scores and productivity indices for external factors are also investigated. Our results indicate that both efficiency and productivity decreased over the five years. We verify that the productivity drop is primarily explained by technical change. Furthermore, certain external variables affected WWTP efficiency, including plant size, treatment technology and energy consumption. However, plants with low energy consumption are the only ones which improve their productivity. Finally, the benchmarking analyses proved to be useful as management tools in the wastewater sector, by providing vital information for improving the sustainability of plants.

  19. Recycling of waste engine oil for diesel production.

    Science.gov (United States)

    Maceiras, R; Alfonsín, V; Morales, F J

    2017-02-01

    The aim of this work was to recycle waste engine oil until converting it into reusable product, diesel fuel. The waste oil was treated using pyrolytic distillation. The effect of two additives (sodium hydroxide and sodium carbonate) in the purification of the obtained fuel was also studied. Moreover, the influence of the number of distillations were analysed. Some thermal and physicochemical properties (density, viscosity, colour, turbidity, acidity value, distillation curves, cetane number, corrosiveness to Cu, water content, flash point and hydrocarbons) were determined to analyse the quality of the obtained fuel. The best results were obtained with 2% of sodium carbonate and two successive distillations. The obtained results showed that pyrolytic distillation of waste engine oil is an excellent way to produce diesel fuel to be used in engines. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Water footprints of products of oil palm plantations and palm oil mills in Thailand.

    Science.gov (United States)

    Suttayakul, Phetrada; H-Kittikun, Aran; Suksaroj, Chaisri; Mungkalasiri, Jitti; Wisansuwannakorn, Ruthairat; Musikavong, Charongpun

    2016-01-15

    The water footprint (WF) of fresh fruit bunches (FFBs) from oil palm plantations and crude palm oil (CPO) from palm oil mills in southern and eastern Thailand were determined over 25 years. Climatic conditions, soil characteristics, and the characteristics of oil palm growth were considered. The WF of FFBs was 1063 m(3)/ton (t) on average. Green, blue, and grey waters comprised of 68, 18, and 14% of total WF, respectively. The oil palm plantations in Thailand required smaller amounts of indirect blue water. The average WF for producing a ton of CPO of seven mills was 5083 m(3). Most of the waters used in the mills originated from indirect green, blue and grey waters from the plantations. The direct blue water used in the mills had less impact on the total WF, lower than 1% of the total WF. Average percentages of green, blue, and grey waters of 69, 16, and 15% of total WF were determined for the mills, respectively. The water deprivation of the FFBs and CPO ranged from 0.73-12.9 and 3.44-58.3 m(3)H2Oeq/t, respectively. In 2013, the CPO production in Thailand including green, blue, and grey waters from plantation and blue water from mills required 11,343 million m(3) water. If the oil palm variety Suratthani 7 is used in the plantation, it would increase the yield from 15.2 to 22.8 t FFBs/ha-year and decrease the WF to 888 m(3)/t FFBs. The average value of the oil extraction rate (OER) of mills was 18.1%. With an increase in the OER of 1%, a reduction of the WF of 250 m(3)/t CPO or 5.1% of total WF could be obtained. Copyright © 2015 Elsevier B.V. All rights reserved.

  1. Waste and product oils recover cash

    Energy Technology Data Exchange (ETDEWEB)

    Mason, R.

    1980-05-01

    Fram Industrial developed a method for removing contaminants from bilge water before dumping it overboard. Framarine separators use a patented arrangement of closely placed corrugated plates aligned horizontally to induce a sinusoidal laminar flow pattern in the oily-water mixture flowing through them, guaranteeing recovery of all droplets larger than 20 microns and a large portion of droplets as small as 7 microns will also be removed. Performance can be accurately predicted by computer whenever the contamination conditions can be defined. The systems and their performance are described. They are being used for pollution control, to recovery liquid products in process plant, and for hydro-metallurgy and other solids separation applications.

  2. Biodiesel Production from Chlorella protothecoides Oil by Microwave-Assisted Transesterification

    OpenAIRE

    G?lyurt, Mustafa ?mer; ?z?imen, Didem; ?nan, Benan

    2016-01-01

    In this study, biodiesel production from microalgal oil by microwave-assisted transesterification was carried out to investigate its efficiency. Transesterification reactions were performed by using Chlorella protothecoides oil as feedstock, methanol, and potassium hydroxide as the catalyst. Methanol:oil ratio, reaction time and catalyst:oil ratio were investigated as process parameters affected methyl ester yield. 9:1 methanol/oil molar ratio, 1.5% KOH catalyst/oil ratio and 10 min were opti...

  3. Okra (Hibiscus esculentus) seed oil for biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    Anwar, Farooq; Nadeem, Muhammad [Department of Chemistry and Biochemistry, University of Agriculture, Faisalabad 38040 (Pakistan); Rashid, Umer [Department of Chemistry and Biochemistry, University of Agriculture, Faisalabad 38040 (Pakistan); Department of Industrial Chemistry, Government College University, Faisalabad 38000 (Pakistan); Ashraf, Muhammad [Department of Botany, University of Agriculture, Faisalabad 38040 (Pakistan)

    2010-03-15

    Biodiesel was derived from okra (Hibiscus esculentus) seed oil by methanol-induced transesterification using an alkali catalyst. Transesterification of the tested okra seed oil under optimum conditions: 7:1 methanol to oil molar ratio, 1.00% (w/w) NaOCH{sub 3} catalyst, temperature 65 C and 600 rpm agitation intensity exhibited 96.8% of okra oil methyl esters (OOMEs) yield. The OOMEs/biodiesel produced was analyzed by GC/MS, which showed that it mainly consisted of four fatty acids: linoleic (30.31%), palmitic (30.23%), oleic (29.09%) and stearic (4.93%). A small amount of 2-octyl cyclopropaneoctanoic acid with contribution 1.92% was also established. Fuel properties of OOMEs such as density, kinematic viscosity, cetane number, oxidative stability, lubricity, flash point, cold flow properties, sulfur contents and acid value were comparable with those of ASTM D 6751 and EN 14214, where applicable. It was concluded that okra seed oil is an acceptable feedstock for biodiesel production. (author)

  4. Cleaner production of citric acid by recycling its extraction wastewater treated with anaerobic digestion and electrodialysis in an integrated citric acid-methane production process.

    Science.gov (United States)

    Xu, Jian; Su, Xian-Feng; Bao, Jia-Wei; Chen, Yang-Qiu; Zhang, Hong-Jian; Tang, Lei; Wang, Ke; Zhang, Jian-Hua; Chen, Xu-Sheng; Mao, Zhong-Gui

    2015-01-01

    To solve the pollution problem of extraction wastewater in citric acid production, an integrated citric acid-methane production process was proposed. Extraction wastewater was treated through anaerobic digestion and the anaerobic digestion effluent (ADE) was recycled for the next batch of citric acid fermentation, thus eliminating wastewater discharge and reducing water consumption. Excessive Na(+) contained in ADE could significantly inhibit citric acid fermentation in recycling and was removed by electrodialysis in this paper. Electrodialysis performance was improved after pretreatment of ADE with air stripping and activated carbon adsorption to remove precipitable metal ions and pigments. Moreover, the concentrate water was recycled and mixed with feed to improve the water recovery rate above 95% in electrodialysis treatment, while the dilute water was collected for citric acid fermentation. The removal rate of Na(+) in ADE was above 95% and the citric acid production was even higher than that with tap water. Copyright © 2015 Elsevier Ltd. All rights reserved.

  5. Effect of food wastewater on biomass production by a green microalga Scenedesmus obliquus for bioenergy generation.

    Science.gov (United States)

    Ji, Min-Kyu; Yun, Hyun-Shik; Park, Sanghyun; Lee, Hongkyun; Park, Young-Tae; Bae, Sunyoung; Ham, Jungyeob; Choi, Jaeyoung

    2015-03-01

    Effect of food wastewater (FW) on the biomass, lipid and carbohydrate production by a green microalga Scenedesmus obliquus cultivated in Bold's Basal Medium (BBM) was investigated. Different dilution ratios (0.5-10%) of BBM either with FW or salt solution (NaCl) or sea water (SW) were evaluated. S. obliquus showed the highest growth (0.41 g L(-1)), lipid productivity (13.3 mg L(-1) day L(-1)), carbohydrate productivity (14.7 mg L(-1) day L(-1)) and nutrient removal (38.9 mg TN L(-1) and 12.1 mg TP L(-1)) with 1% FW after 6 days of cultivation. The FW promoted algal autoflocculation due to formation of inorganic precipitates at an alkali pH. Fatty acid methyl ester analysis revealed that the palmitic and oleic acid contents were increased up to 8% with FW. Application of FW improved the growth, lipid/carbohydrate productivity and biomass recovery efficiency of S. obliquus, which can be exploited for cost effective production of microalgae biomass. Copyright © 2014 Elsevier Ltd. All rights reserved.

  6. Performance of Submerged Aerated Biofilters for Wastewater Treatment and Excess Biological Sludge Production

    Directory of Open Access Journals (Sweden)

    Mohammad A. Baghapour

    2007-01-01

    Full Text Available Minimizing sludge production in the treatment facility is a reasonable measure to reduce waste in sewage treatment, especially as regards excess biological sludge. In this regard, submerged aerated filters' (SAFs have recently found increasing applications in treatment facilities. Thanks to their treatment mechanism, they have greatly contributed to reduction of waste production and, thereby, to reduced treatment costs. Biomass growths of both attached and suspended types take place in these filters. However, little attention has been paid to suspended sludge production and to its relationship with the physical properties of the filter. The design and application criterion for these filters is the organic loadings on unit of area or unit of volume of the media used in these filters. In this study, four filters with different physical properties and different specific areas were loaded with synthetic wastewater made of low-fat dry milk powder for five different hydraulic retention times to evaluate excess sludge production rates in submerged aerated filters. It was shown that increasing specific area increased SCOD removal efficiency up to a maximum level in saturated growths after which point the removal efficiency remained unchanging or decreased. The results also revealed that decreased hydraulic retention times increased sludge production rates in all the study columns and that media with higher porosity levels produced less excess sludge despite lower pollutant removal efficiency.

  7. Characterizing risk factors for pediatric lamp oil product exposures.

    Science.gov (United States)

    Sheikh, S; Chang, A; Kieszak, S; Law, R; Bennett, H K W; Ernst, E; Bond, G R; Spiller, H A; Schurz-Rogers, H; Chu, A; Bronstein, A C; Schier, J G

    2013-11-01

    Poisonings from lamp oil ingestion continue to occur worldwide among the pediatric population despite preventive measures such as restricted sale of colored and scented lamp oils. This suggests that optimal prevention practices for unintentional pediatric exposures to lamp oil have yet to be identified and/or properly implemented. To characterize demographic, health data, and potential risk factors associated with reported exposures to lamp oil by callers to poison centers (PCs) in the US and discuss their public health implications. This was a two part study in which the first part included characterizing all exposures to a lamp oil product reported to the National Poison Data System (NPDS) with regard to demographics, exposure, health, and outcome data from 1/1/2000 to 12/31/2010. Regional penetrance was calculated using NPDS data by grouping states into four regions and dividing the number of exposure calls by pediatric population per region (from the 2000 US census). Temporal analyses were performed on NPDS data by comparing number of exposures by season and around the July 4th holiday. Poisson regression was used to model the count of exposures for these analyses. In the second part of this project, in order to identify risk factors we conducted a telephone-based survey to the parents of children from five PCs in five different states. The 10 most recent lamp oil product exposure calls for each poison center were systematically selected for inclusion. Calls in which a parent or guardian witnessed a pediatric lamp oil product ingestion were eligible for inclusion. Data on demographics, exposure information, behavioral traits, and health were collected. A descriptive analysis was performed and Fisher's exact test was used to evaluate associations between variables. All analyses were conducted using SAS v9.3. Among NPDS data, 2 years was the most common patient age reported and states in the Midwestern region had the highest numbers of exposure calls compared to

  8. Energy production from distillery wastewater using single and double-phase upflow anaerobic sludge blanket (UASB) reactor

    Energy Technology Data Exchange (ETDEWEB)

    Muyodi, F J; Rubindamayugi, M S.T. [Univ. of Dar es Salaam, Applied Microbiology Unit (Tanzania, United Republic of)

    1998-12-31

    A Single-phase (SP) and Double-phase (DP) Upflow Anaerobic Sludge Blanket (UASB) reactors treating distillery wastewater were operated in parallel. The DP UASB reactor showed better performance than the SP UASB reactor in terms of maximum methane production rate, methane content and Chemical Oxygen Demand (COD) removal efficiency. (au) 20 refs.

  9. Energy production from distillery wastewater using single and double-phase upflow anaerobic sludge blanket (UASB) reactor

    Energy Technology Data Exchange (ETDEWEB)

    Muyodi, F.J.; Rubindamayugi, M.S.T. [Univ. of Dar es Salaam, Applied Microbiology Unit (Tanzania, United Republic of)

    1997-12-31

    A Single-phase (SP) and Double-phase (DP) Upflow Anaerobic Sludge Blanket (UASB) reactors treating distillery wastewater were operated in parallel. The DP UASB reactor showed better performance than the SP UASB reactor in terms of maximum methane production rate, methane content and Chemical Oxygen Demand (COD) removal efficiency. (au) 20 refs.

  10. Analysis and optimization of process parameters for production of polyhydroxyalkanoates along with wastewater treatment by Serratia sp. ISTVKR1.

    Science.gov (United States)

    Gupta, Asmita; Kumar, Madan; Thakur, Indu Shekhar

    2017-10-01

    A previously reported biodegrading bacterial strain Serratia sp. ISTVKR1 was studied for polyhydroxyalkanoate (PHA) production along with wastewater contaminant removal. Nile red fluorescence, GC-MS, FT-IR, NMR and TEM confirmed the accumulation of homopolymer poly-3-hydroxyvalerate (PHV) within the bacterial cells. Analysis of culture after 72h of bacterial treatment showed maximum COD removal (8.4-fold), non-detection of organic contaminants such as 1H-Cyclopropa [a] naphthalene (R.T.=10.12) using GC-MS and increased proportion of elements like Cr, Mn, Fe, Ni, Cu, Cd and Pb in the bacterial cell pellets by SEM-EDX analysis. Optimization of process parameters for enhanced PHA production along with wastewater treatment done using Response Surface Methodology (RSM) showed 5% and 0.74% increase in the PHA production (0.3368±0.13gL -1 ) and % COD reduction (88.93±2.41) of wastewater, respectively. The study, thus established the production of PHA along with wastewater contaminant removal by Serratia sp. ISTVKR1. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. SOURCES OF COPPER IONS AND SELECTED METHODS OF THEIR REMOVAL FROM WASTEWATER FROM THE PRINTED CIRCUITS BOARD PRODUCTION

    Directory of Open Access Journals (Sweden)

    Maciej Thomas

    2014-10-01

    Full Text Available This paper presents the issues related to the presence and removal of copper compounds from industrial effluents with including wastewater from plants involved in the production of printed circuit boards. Characterized the toxicological properties of selected copper compounds, described the applicable technological processes, sources of copper ions in the effluents and selected methods for their removal.

  12. Spray drying of a phenolic-rich membrane filtration fraction of olive mill wastewater</