WorldWideScience

Sample records for objective sheets information

  1. Energy information sheets

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    The National Energy Information Center (NEIC), as part of its mission, provides energy information and referral assistance to Federal, State, and local governments, the academic community, business and industrial organizations, and the public. The Energy Information Sheets was developed to provide general information on various aspects of fuel production, prices, consumption, and capability. Additional information on related subject matter can be found in other Energy Information Administration (EIA) publications as referenced at the end of each sheet.

  2. Energy information sheets

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-02

    The National Energy Information Center (NEIC), as part of its mission, provides energy information and referral assistance to Federal, State, and local governments, the academic community, business and industrial organizations, and the general public. Written for the general public, the EIA publication Energy Information Sheets was developed to provide information on various aspects of fuel production, prices, consumption and capability. The information contained herein pertains to energy data as of December 1991. Additional information on related subject matter can be found in other EIA publications as referenced at the end of each sheet.

  3. Information sheets on energy

    International Nuclear Information System (INIS)

    2004-01-01

    These sheets, presented by the Cea, bring some information, in the energy domain, on the following topics: the world energy demand and the energy policy in France and in Europe, the part of the nuclear power in the energy of the future, the greenhouse gases emissions and the fight against the greenhouse effect, the carbon dioxide storage cost and the hydrogen economy. (A.L.B.)

  4. Energy information sheets, July 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    The National Energy Information Center (NEIC), as part of its mission, provides energy information and referral assistance to Federal, State, and local governments, the academic community, business and industrial organizations, and the public. The Energy Information Sheets was developed to provide general information on various aspects of fuel production, prices, consumption, and capability. Additional information on related subject matter can be found in other Energy Information Administration (EIA) publications as referenced at the end of each sheet.

  5. Energy information sheets, September 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-01

    The National Energy Information Center (NEIC), as part of its mission, provides energy information and referral assistance to Federal, State, and local governments, the academic community, business and industrial organizations, and the public. The Energy Information Sheets was developed to provide general information on various aspects of fuel production, prices, consumption, and capability. Additional information on related subject matter can be found in other Energy Information Administration (EIA) publications as referenced at the end of each sheet.

  6. Production (information sheets)

    NARCIS (Netherlands)

    2007-01-01

    Documentation sheets: Geo energy 2 Integrated System Approach Petroleum Production (ISAPP) The value of smartness 4 Reservoir permeability estimation from production data 6 Coupled modeling for reservoir application 8 Toward an integrated near-wellbore model 10 TNO conceptual framework for "E&P

  7. Investigating Music Information Objects

    Science.gov (United States)

    Weissenberger, Lynnsey K.

    2016-01-01

    This dissertation, titled "Investigating Music Information Objects," is a study of the nature, description, representations, and ideas related to music information objects (MIOs). This research study investigates how music practitioners from various traditions describe and conceptualize MIOs, using a theoretical framework to classify…

  8. Multi-objective optimization under uncertainty for sheet metal forming

    Directory of Open Access Journals (Sweden)

    Lafon Pascal

    2016-01-01

    Full Text Available Aleatory uncertainties in material properties, blank thickness and friction condition are inherent and irreducible variabilities in sheet metal forming. Optimal design configurations, which are obtained by conventional design optimization methods, are not always able to meet the desired targets due to the effect of uncertainties. This paper proposes a multi-objective robust design optimization that aims to tackle this problem. Results obtained on a U shape draw bending benchmark show that spring-back effect can be controlled by optimizing process parameters.

  9. Sense and readability: participant information sheets for research studies.

    Science.gov (United States)

    Ennis, Liam; Wykes, Til

    2016-02-01

    Informed consent in research is partly achieved through the use of information sheets. There is a perception however that these information sheets are long and complex. The recommended reading level for patient information is grade 6, or 11-12 years old. To investigate whether the readability of participant information sheets has changed over time, whether particular study characteristics are related to poorer readability and whether readability and other study characteristics are related to successful study recruitment. Method: We obtained 522 information sheets from the UK National Institute for Health Research Clinical Research Network: Mental Health portfolio database and study principal investigators. Readability was assessed with the Flesch reading index and the Grade level test. Information sheets increased in length over the study period. The mean grade level across all information sheets was 9.8, or 15-16 years old. A high level of patient involvement was associated with more recruitment success and studies involving pharmaceutical or device interventions were the least successful. The complexity of information sheets had little bearing on successful recruitment. Information sheets are far more complex than the recommended reading level of grade 6 for patient information. The disparity may be exacerbated by an increasing focus on legal content. Researchers would benefit from clear guidance from ethics committees on writing succinctly and accessibly and how to balance the competing legal issues with the ability of participants to understand what a study entails. © The Royal College of Psychiatrists 2016.

  10. World War II Informational Fact Sheets.

    Science.gov (United States)

    Department of Defense, Washington, DC.

    This commemorative book provides numerous fact sheets on various aspects of World War II, both on the fighting front and the homefront. Replicas of posters of the war era, descriptions of battles with maps, contributions of women and minorities to the war effort, even music of the wartime era, add to this collection of resource materials useful to…

  11. The National Agriculture Imagery Program (NAIP) Information Sheet

    Data.gov (United States)

    Farm Service Agency, Department of Agriculture — This story map journal is an interactive version of the NAIP information sheet provided on the Aerial Photography Field Office web site. This map journal provides...

  12. Epilepsy: General Information. Fact Sheet Number 6 = La Epilepsia: Informacion General. Fact Sheet Number 20.

    Science.gov (United States)

    Interstate Research Associates, McLean, VA.

    This fact sheet on epilepsy is offered in both English and Spanish. It provides a definition, information on incidence, typical characteristics, and educational implications. It notes that epilepsy is classified as "other health impaired" under the Individuals with Disabilities Education Act and that students with epilepsy are eligible for special…

  13. Autism: General Information. Fact Sheet Number 1 = Autismo: Informacion General. Fact Sheet Number 22.

    Science.gov (United States)

    Interstate Research Associates, McLean, VA.

    This fact sheet on autism is offered in both English and Spanish, and is the same in both languages although numbered differently. It provides a definition, information on incidence, typical characteristics, and educational implications. It notes that autism is listed as a separate category under the Individuals with Disabilities Education Act.…

  14. Scribbling on the blank sheet: Eddington's structuralist conception of objects

    Science.gov (United States)

    French, Steven

    Although Eddington's philosophy of physics has been subjected to critical re-evaluation in recent years, neither the exact nature of his structuralist views nor his response to criticism by the likes of Braithwaite have been made clear. In this paper I trace, in particular, the incorporation into Eddington's structuralism of the non-classical indistinguishability of quantum objects. His metaphysical view of such objects as the product of group-theoretical analysis is crucial for understanding his response to Braithwaite's criticisms of the whole structuralist endeavor. These criticisms closely resemble more recent attacks on structural realism in the philosophy of science. I conclude with a brief comparison between these more modern forms of structuralism and Eddington's.

  15. Chernobyl: before and after. Information sheet No. 1

    Energy Technology Data Exchange (ETDEWEB)

    Devine, J [comp.

    1986-01-01

    Complied in June 1986 the information sheet lists title, authors, and journal details and gives brief details of all relevant published articles. Part 1 concerns material relevant before the accident in April 1986 - the construction, design and safety of the Chernobyl RBMK nuclear power station (20 references). Part 2 lists articles published after the accident concerning the impact of the disaster on safety in the nuclear power industry (23 references).

  16. Information – is it Subjective or Objective?

    Directory of Open Access Journals (Sweden)

    Andrzej Stanislaw Zaliwski

    2011-03-01

    Full Text Available The article deals first with the problems of defining information. It is concluded that it is a misunderstanding to take a term and then to look for a definition. Rather a different way ought to be taken: to find the phenomenon first and then assign a name to it. The view that information is the same thing as a structure is considered. Then the processes by which information is created are analyzed. The definition that information is detected difference is closely scrutinized and it is found that information can also be detected sameness. It is argued that information is relative to the observer and for the very reason of the way it is created it is subjective. That extends only to information acquired. The existence of subjective information, however, does not prove information cannot exist objectively.

  17. An object-oriented, coprocessor-accelerated model for ice sheet simulations

    Science.gov (United States)

    Seddik, H.; Greve, R.

    2013-12-01

    Recently, numerous models capable of modeling the thermo-dynamics of ice sheets have been developed within the ice sheet modeling community. Their capabilities have been characterized by a wide range of features with different numerical methods (finite difference or finite element), different implementations of the ice flow mechanics (shallow-ice, higher-order, full Stokes) and different treatments for the basal and coastal areas (basal hydrology, basal sliding, ice shelves). Shallow-ice models (SICOPOLIS, IcIES, PISM, etc) have been widely used for modeling whole ice sheets (Greenland and Antarctica) due to the relatively low computational cost of the shallow-ice approximation but higher order (ISSM, AIF) and full Stokes (Elmer/Ice) models have been recently used to model the Greenland ice sheet. The advance in processor speed and the decrease in cost for accessing large amount of memory and storage have undoubtedly been the driving force in the commoditization of models with higher capabilities, and the popularity of Elmer/Ice (http://elmerice.elmerfem.com) with an active user base is a notable representation of this trend. Elmer/Ice is a full Stokes model built on top of the multi-physics package Elmer (http://www.csc.fi/english/pages/elmer) which provides the full machinery for the complex finite element procedure and is fully parallel (mesh partitioning with OpenMPI communication). Elmer is mainly written in Fortran 90 and targets essentially traditional processors as the code base was not initially written to run on modern coprocessors (yet adding support for the recently introduced x86 based coprocessors is possible). Furthermore, a truly modular and object-oriented implementation is required for quick adaptation to fast evolving capabilities in hardware (Fortran 2003 provides an object-oriented programming model while not being clean and requiring a tricky refactoring of Elmer code). In this work, the object-oriented, coprocessor-accelerated finite element

  18. Information model of the 'Ukryttya' object

    International Nuclear Information System (INIS)

    Batij, E.V.; Ermolenko, A.A.; Kotlyarov, V.T.

    2008-01-01

    There were described the building principles and content of the 'Ukryttya' object information model that has been developed at the Institute for Safety Problems of NPP. Using the client/server architecture in this system (the simultaneous access of the many users), Autodesk Map Guide and ASP.NET technologies allowed avoiding the typical defects of the 'stand-alone desktop' information systems (that aimed for a single user)

  19. Improving postoperative tonsillectomy pain management in children--a double blinded randomised control trial of a patient analgesia information sheet.

    Science.gov (United States)

    Bailey, Lucas; Sun, Jing; Courtney, Mark; Murphy, Paul

    2015-05-01

    To evaluate paediatric post-tonsillectomy pain management using oxycodone when a specific analgesia information sheet is included with standard postoperative information. Oxycodone information sheets were randomly allocated to half the study children's post-tonsillectomy information pack. The trial was double-blinded to the surgeon, anaesthetist, nursing and administrative staff. Parents and children completed the pain assessment on day 3, 5 and 7. On day 10 the parents completed a questionnaire. A postoperative analgesia information sheet provides for higher satisfaction and knowledge for parents using oxycodone (psheet, most significantly at day 3 and 7 post operatively (psheets are useful in education and use of postoperative analgesia. The primary objective to explore the efficacy of the information sheet has proved to be successful in this setting. Given risks of opioid analgesia, it is recommended that postoperative information sheets be given to all parents, to provide for improved analgesia control and safe management of children in the postoperative period. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  20. General Information about Learning Disabilities (Fact Sheet Number 7) = Informacion General sobre Impedimentos en el Aprendizaje (Fact Sheet Number 19).

    Science.gov (United States)

    Interstate Research Associates, Inc., Washington, DC.

    This fact sheet providing general information about learning disabilities is presented in both English and Spanish versions. It begins with the federal definition of learning disabilities and a discussion of its implications followed by estimates of incidence. Typical characteristics of students with learning disabilities are then summarized as…

  1. Information sheets on energy; Fiches information sur l'energie

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    These sheets, presented by the Cea, bring some information, in the energy domain, on the following topics: the world energy demand and the energy policy in France and in Europe, the part of the nuclear power in the energy of the future, the greenhouse gases emissions and the fight against the greenhouse effect, the carbon dioxide storage cost and the hydrogen economy. (A.L.B.)

  2. Exploratory Study on the Capitalization of Accounting Information by Financial Constructions Determined on the Basis of the Balance Sheet

    Directory of Open Access Journals (Sweden)

    Ciuhureanu Alina-Teodora

    2017-12-01

    Full Text Available The capitalization of the information provided through the balance sheet should be one of the priorities of the organization’s manager. This is because the processed accounting information is the one that contributes to the setting of objectives and strategy and at the same time provides the necessary information capital for proper management of the activity. For these reasons, the article presents a series of financial constructions based on the accounting information provided through the financial accounting system and centralized in the balance sheet. The aim of the paper is to capture the benefits of using it by management and not to detail indicators / rates / tools in terms of calculation methods.

  3. 14 CFR 1203.201 - Information security objectives.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Information security objectives. 1203.201 Section 1203.201 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION INFORMATION SECURITY PROGRAM NASA Information Security Program § 1203.201 Information security objectives. The objectives of...

  4. Multi-Objective Parallel Test-Sheet Composition Using Enhanced Particle Swarm Optimization

    Science.gov (United States)

    Ho, Tsu-Feng; Yin, Peng-Yeng; Hwang, Gwo-Jen; Shyu, Shyong Jian; Yean, Ya-Nan

    2009-01-01

    For large-scale tests, such as certification tests or entrance examinations, the composed test sheets must meet multiple assessment criteria. Furthermore, to fairly compare the knowledge levels of the persons who receive tests at different times owing to the insufficiency of available examination halls or the occurrence of certain unexpected…

  5. The 'MELUSINE' reactor at Grenoble, France, and associated hot cell facilities. Information sheets

    International Nuclear Information System (INIS)

    Hardt, P. von der; Roettger, H.

    1981-01-01

    Technical information is given on the MELUSINE reactor and associated hot cell facilities, with the main emphasis on experimental irradiation facilities and specialized irradiation devices (loops and capsules). The information is presented in the form of six information sheets under the headings: main characteristics of the reactor; utilization and specialization of the reactor; experimental facilities; neutron spectra; main characteristics of specialized irradiation devices; main characteristics of hot cell facilities

  6. Augmentative Device Helps Max Speak. PACER Center ACTion Information Sheets. PHP-c75

    Science.gov (United States)

    PACER Center, 2014

    2014-01-01

    This Action Information Sheet follows a family's process of selecting and using augmentative and alternative communication to help their young son, Max, speak. Max is affected by global dyspraxia, which makes learning new motor skills--especially speech--quite difficult. For the first years of his life, Max could not say words. Before he and his…

  7. Know Your School District: Tips for Parents. PACER Center ACTion Information Sheets. PHP-c112

    Science.gov (United States)

    PACER Center, 2006

    2006-01-01

    Becoming familiar with the school district will help parents become active and involved partners in their child's education. Research has demonstrated that family involvement in children's education can boost their academic success. Knowing about the following areas, which are discussed in this information sheet, can help parental involvement at…

  8. Fuels planning: science synthesis and integration; environmental consequences fact sheet 01: Fire Effects Information System (FEIS)

    Science.gov (United States)

    Steve Sutherland

    2004-01-01

    The Fire Effects Information System (FEIS) provides accessible, up-to-date fire effects summaries, taken from current English-language literature, for almost 900 plant species, about 100 animal species, and 16 Kuchler plant communities found on the North American continent. This fact sheet discusses the development of FEIS and what is contained in the species summary....

  9. Cerebral Palsy: General Information. Fact Sheet Number 2 = La Paralisis Cerebral: Informacion General. Fact Sheet Number 18.

    Science.gov (United States)

    Interstate Research Associates, McLean, VA.

    This fact sheet on cerebral palsy is offered in both English and Spanish. First, it provides a definition and considers various causes (e.g., an insufficient amount of oxygen reaching the fetal or newborn brain). The fact sheet then offers incidence figures and explains characteristics of the three main types of cerebral palsy: spastic, athetoid,…

  10. Spina Bifida: General Information. Fact Sheet Number 12 = La Espina Bifida: Informacion General. Fact Sheet Number 12.

    Science.gov (United States)

    National Information Center for Children and Youth with Disabilities, Washington, DC.

    This fact sheet offers definitions of the three types of spina bifida, outlines their incidence, describes characteristics of individuals with spina bifida, and reviews educational implications. The fact sheet emphasizes that school programs should be flexible to accommodate these students' special needs and frequent absences, that children with…

  11. Development of Information Technology of Object-relational Databases Design

    Directory of Open Access Journals (Sweden)

    Valentyn A. Filatov

    2012-12-01

    Full Text Available The article is concerned with the development of information technology of object-relational databases design and study of object features infological and logical database schemes entities and connections.

  12. Conceptual Modeling of Events as Information Objects and Change Agents

    DEFF Research Database (Denmark)

    Bækgaard, Lars

    as a totality of an information object and a change agent. When an event is modeled as an information object it is comparable to an entity that exists only at a specific point in time. It has attributes and can be used for querying and specification of constraints. When an event is modeled as a change agent...... it is comparable to an executable transaction schema. Finally, we briefly compare our approach to object-oriented approaches based on encapsulated objects....

  13. Optical Aperture Synthesis Object's Information Extracting Based on Wavelet Denoising

    International Nuclear Information System (INIS)

    Fan, W J; Lu, Y

    2006-01-01

    Wavelet denoising is studied to improve OAS(optical aperture synthesis) object's Fourier information extracting. Translation invariance wavelet denoising based on Donoho wavelet soft threshold denoising is researched to remove Pseudo-Gibbs in wavelet soft threshold image. OAS object's information extracting based on translation invariance wavelet denoising is studied. The study shows that wavelet threshold denoising can improve the precision and the repetition of object's information extracting from interferogram, and the translation invariance wavelet denoising information extracting is better than soft threshold wavelet denoising information extracting

  14. New Grounds for Ontic Trust: Information Objects and LIS

    Science.gov (United States)

    Van der Veer Martens, Betsy

    2017-01-01

    The information ethics of Luciano Floridi's well-known Philosophy of Information (PI) project are explored as potential foundations for a deepening sense of stewardship in library and information studies (LIS) practice. The implications of PI's world view of "information objects" as having intrinsic value and resulting moral rights…

  15. Decreased attention to object size information in scale errors performers

    NARCIS (Netherlands)

    Grzyb, B.J.; Cangelosi, A.; Cattani, A.; Floccia, C.

    2017-01-01

    Young children sometimes make serious attempts to perform impossible actions on miniature objects as if they were full-size objects. The existing explanations of these curious action errors assume (but never explicitly tested) children’s decreased attention to object size information. This study

  16. EQUILIBRIUM ANALYSIS OF FINANCIAL COMPANY BASED ON INFORMATION PROVIDED BY THE BALANCE SHEET

    Directory of Open Access Journals (Sweden)

    Ștefăniță ȘUȘU

    2014-06-01

    Full Text Available This article highlights the importance of indicators (as net working capital, working capital requirements and net cash by means of which it is considered in the context of financial balances capitalization information released by the balance sheet of an entity tourist profile. Theoretical concepts presented in a logical sequence are combined with the practical example transposed Turism Covasna company. The results of the analysis are interpreted while trying to formulate solutions to the economic and financial viability of the entity.

  17. The 'SILOE' reactor at Grenoble, France and associated hot cell facilities. Information sheets

    International Nuclear Information System (INIS)

    Hardt, P. von der; Roettger, H.

    1981-01-01

    Technical information is given on the SILOE reactor and associated hot cell facilities, with the main emphasis on experimental irradiation facilities, specialized irradiation devices (loops and capsules) and possibilities for post-irradiation examinations of samples. The information is presented in the form of eight information sheets under the headings: main characteristics of the reactor; utilization and specialization of the reactor; experimental facilities; neutron spectra; main characteristics of specialized irradiation devices; main characteristics of hot cell facilities; equipment and techniques available for post-irradiation examinations; utilization and specialization of the hot cell facilities

  18. The DR 3 reactor at Risoe, Denmark and its associated hot cell facilities. Information sheets

    International Nuclear Information System (INIS)

    Hardt, P. von der; Roettger, H.

    1981-01-01

    Technical information is given on the DR 2 reactor and associated hot cell facilities, with the main emphasis on experimental irradiation facilities, specialized irradiation devices (loops and capsules) and possibilities for post-irradiation examinations of samples. The information is presented in the form of seven information sheets under the headings: main characteristics of the reactor; utilization and specialization of the reactor; experimental facilities; main characteristics of specialized irradiation devices; main characteristics of hot cell facilities; equipment and techniques available for post-irradiation examinations; utilization and specialization of the hot cell facilities

  19. The DIDO-reactor at Harwell, U.K. and ancillary hot cell facilities. Information sheets

    International Nuclear Information System (INIS)

    Hardt, P. von der; Roettger, H.

    1981-01-01

    Technical information is given on the DIDO reactor and associated hot cell facilities, with the main emphasis on experimental irradiation facilities, specialized irradiation devices (loops and capsules) and possibilities for post-irradiation examinations of samples. The information is presented in the form of eight information sheets under the headings: main characteristics of the reactor; utilization and specialization of the reactor; experimental facilities; neutron spectra; main characteristics of specialized irradiation devices; main characteristics of hot cell facilities; equipment and techniques available for post-irradiation examinations; utilization and specialization of the hot cell facilities

  20. The 'OSIRIS' reactor at Saclay, France and available hot cell facilities. Information sheets

    International Nuclear Information System (INIS)

    Hardt, P. von der; Roettger, H.

    1981-01-01

    Technical information is given on the OSIRIS reactor and associated hot cell facilities, with the main emphasis on experimental irradiation facilities, specialized irradiation devices (loops and capsules) and possibilities for post-irradiation examinations of samples. The information is presented in the form of eight information sheets under the headings: main characteristics of the reactor; utilization and specialization of the reactor; experimental facilities; neutron spectra; main characteristics of specialized irradiation devices; main characteristics of hot cell facilities; equipment and techniques available for post-irradiation examinations; utilization and specialization of the hot cell facilities

  1. Multi-objective robust optimization method for the modified epoxy resin sheet molding compounds of the impeller

    Directory of Open Access Journals (Sweden)

    Xiaozhang Qu

    2016-07-01

    Full Text Available A kind of modified epoxy resin sheet molding compounds of the impeller has been designed. Through the test, the non-metal impeller has a better environmental aging performance, but must do the waterproof processing design. In order to improve the stability of the impeller vibration design, the influence of uncertainty factors is considered, and a multi-objective robust optimization method is proposed to reduce the weight of the impeller. Firstly, based on the fluid-structure interaction,the analysis model of the impeller vibration is constructed. Secondly, the optimal approximate model of the impeller is constructed by using the Latin hypercube and radial basis function, and the fitting and optimization accuracy of the approximate model is improved by increasing the sample points. Finally, the micro multi-objective genetic algorithm is applied to the robust optimization of approximate model, and the Monte Carlo simulation and Sobol sampling techniques are used for reliability analysis. By comparing the results of the deterministic, different sigma levels and different materials, the multi-objective optimization of the SMC molding impeller can meet the requirements of engineering stability and lightweight. And the effectiveness of the proposed multi-objective robust optimization method is verified by the error analysis. After the SMC molding and the robust optimization of the impeller, the optimized rate reached 42.5%, which greatly improved the economic benefit, and greatly reduce the vibration of the ventilation system.

  2. Market Research on Law School Student Aid Award Letters and Shopping Sheet Information. NASFAA Consumer Information & Law Student Indebtedness Task Force Report

    Science.gov (United States)

    National Association of Student Financial Aid Administrators, 2016

    2016-01-01

    "Market Research on Law School Student Aid Award Letters and Shopping Sheet Information" set out to identify through consumer testing what information on the financial aid award letter and U.S. Department of Education's (ED) Shopping Sheet could be modified to create a document that better assists students applying to, or currently…

  3. Down Syndrome: General Information. Fact Sheet Number 4 = El Sindrome de Down: Informacion General. Fact Sheet Number 15.

    Science.gov (United States)

    Interstate Research Associates, McLean, VA.

    This fact sheet on Down Syndrome is offered in both English and Spanish. First it provides a definition and description of this syndrome, noting its etiology in a chromosomal abnormality. Incidence figures are then given. Typical characteristics of people with Down Syndrome are listed. Commonly associated health-related problems are noted,…

  4. Spina Bifida: General Information. Fact Sheet Number 12 = La Espina Bifida: Informacion General. Fact Sheet Number 21.

    Science.gov (United States)

    Interstate Research Associates, McLean, VA.

    This fact sheet on spina bifida is offered in both English and Spanish. It provides definitions of the three types of spina bifida (spina bifida occulta, meningocele, and myelomeningocele). Incidence figures are given as are typical characteristics of children with spina bifida. Educational implications are briefly noted, including the need to…

  5. Interrogation of an object for dimensional and topographical information

    Science.gov (United States)

    McMakin, Doug L [Richland, WA; Severtsen, Ronald H [Richland, WA; Hall, Thomas E [Richland, WA; Sheen, David M [Richland, WA

    2003-01-14

    Disclosed are systems, methods, devices, and apparatus to interrogate a clothed individual with electromagnetic radiation to determine one or more body measurements at least partially covered by the individual's clothing. The invention further includes techniques to interrogate an object with electromagnetic radiation in the millimeter and/or microwave range to provide a volumetric representation of the object. This representation can be used to display images and/or determine dimensional information concerning the object.

  6. Grasping an object comfortably: orientation information is held in memory

    NARCIS (Netherlands)

    Roche, K; Verheij, R.; Voudouris, D.; Chainay, H.; Smeets, J.B.J.

    2015-01-01

    It has been shown that memorized information can influence real-time visuomotor control. For instance, a previously seen object (prime) influences grasping movements toward a target object. In this study, we examined how general the priming effect is: does it depend on the orientation of the target

  7. A Moving Object Detection Algorithm Based on Color Information

    International Nuclear Information System (INIS)

    Fang, X H; Xiong, W; Hu, B J; Wang, L T

    2006-01-01

    This paper designed a new algorithm of moving object detection for the aim of quick moving object detection and orientation, which used a pixel and its neighbors as an image vector to represent that pixel and modeled different chrominance component pixel as a mixture of Gaussians, and set up different mixture model of Gauss for different YUV chrominance components. In order to make full use of the spatial information, color segmentation and background model were combined. Simulation results show that the algorithm can detect intact moving objects even when the foreground has low contrast with background

  8. The development of KAERI management information system (II) -The development of Time Sheet Management System-

    International Nuclear Information System (INIS)

    Kang, Sin Bok; Kim, Yeong Taek; Park, Soo Jin; Ko, Yeong Cheol; Lee, Jong Bok; Han, Eun Sook; Kim, Hyeon Jeong

    1994-01-01

    The purpose of this report is to describe the work done for the development, operation and maintenance of Time Sheet Management System. This work is a part of the development KAERI management information system. Manpower management is essential to cope with the external circumstances promptly and to maximize the productivity of the organization. This work aims at setting up a basis for the manpower management system. It is widely recognized that neither timely decision making nor competitive edge can be secured with the traditional management technology in so a rapidly changing situations home and abroad, which can be characterized by openness and informality. The necessity of efficient and scientific man-power management by time-study has emerged on the reorganization of KAERI by expanding matrix system in order to enhance the R and D productivity. (Author)

  9. Decreased attention to object size information in scale errors performers.

    Science.gov (United States)

    Grzyb, Beata J; Cangelosi, Angelo; Cattani, Allegra; Floccia, Caroline

    2017-05-01

    Young children sometimes make serious attempts to perform impossible actions on miniature objects as if they were full-size objects. The existing explanations of these curious action errors assume (but never explicitly tested) children's decreased attention to object size information. This study investigated the attention to object size information in scale errors performers. Two groups of children aged 18-25 months (N=52) and 48-60 months (N=23) were tested in two consecutive tasks: an action task that replicated the original scale errors elicitation situation, and a looking task that involved watching on a computer screen actions performed with adequate to inadequate size object. Our key finding - that children performing scale errors in the action task subsequently pay less attention to size changes than non-scale errors performers in the looking task - suggests that the origins of scale errors in childhood operate already at the perceptual level, and not at the action level. Copyright © 2017 Elsevier Inc. All rights reserved.

  10. Objective Evaluation in an Online Geographic Information System Certificate Program

    OpenAIRE

    Scott L. WALKER

    2005-01-01

    Objective Evaluation in an Online Geographic Information System Certificate Program Asst. Professor. Dr. Scott L. WALKER Texas State University-San Marcos San Marcos, Texas, USA ABSTRACT Departmental decisions regarding distance education programs can be subject to subjective decision-making processes influenced by external factors such as strong faculty opinions or pressure to increase student enrolment. This paper outlines an evaluation of a departmental distance-education program....

  11. Discovering objects in a blood recipient information system.

    Science.gov (United States)

    Qiu, D; Junghans, G; Marquardt, K; Kroll, H; Mueller-Eckhardt, C; Dudeck, J

    1995-01-01

    Application of object-oriented (OO) methodologies has been generally considered as a solution to the problem of improving the software development process and managing the so-called software crisis. Among them, object-oriented analysis (OOA) is the most essential and is a vital prerequisite for the successful use of other OO methodologies. Though there are already a good deal of OOA methods published, the most important aspect common to all these methods: discovering objects classes truly relevant to the given problem domain, has remained a subject to be intensively researched. In this paper, using the successful development of a blood recipient information system as an example, we present our approach which is based on the conceptual framework of responsibility-driven OOA. In the discussion, we also suggest that it may be inadequate to simply attribute the software crisis to the waterfall model of the software development life-cycle. We are convinced that the real causes for the failure of some software and information systems should be sought in the methodologies used in some crucial phases of the software development process. Furthermore, a software system can also fail if object classes essential to the problem domain are not discovered, implemented and visualized, so that the real-world situation cannot be faithfully traced by it.

  12. Exploring Parenting: Information Sheets for Parents = Explorando El Arte de Ser Padres: Hojas informativas para los padres.

    Science.gov (United States)

    Administration for Children, Youth, and Families (DHHS), Washington, DC. Head Start Bureau.

    This document, provided here in separate English and Spanish versions, is a collection of informational and instructional sheets for parents of young children, divided into 20 thematic sections. Each of the sections includes information on the topic area, some learning activities, and questions for discussion. The sessions are: (1) "Getting…

  13. The patent, object of research in Information Science and Communication

    Directory of Open Access Journals (Sweden)

    Luc Quoniam

    2014-04-01

    Full Text Available In this study are addressed some dimensions of intellectual property, especially patents and their way of making some tangible outcomes of research and development, playing a key role in the field of strategy, involving the returns on investments and exploration rights to certain inventions. However, the general objective of this study is to present aspects of the information available in patent applications and the possibility of using them to transfer technology between countries, organizations, contribute to the research of social responsibility, valuing natural resources and provide access to medicines, once these are aspects little attention in the literature. Considering the patent as an object of study in the humanities and social sciences, is evidenced by the cases cited, the potential contribution to innovation, research and development organizations, regions and countries.

  14. Promoting social responsibility amongst health care users: medical tourists’ perspectives on an information sheet regarding ethical concerns in medical tourism

    Science.gov (United States)

    2013-01-01

    Background Medical tourists, persons that travel across international borders with the intention to access non-emergency medical care, may not be adequately informed of safety and ethical concerns related to the practice of medical tourism. Researchers indicate that the sources of information frequently used by medical tourists during their decision-making process may be biased and/or lack comprehensive information regarding individual safety and treatment outcomes, as well as potential impacts of the medical tourism industry on third parties. This paper explores the feedback from former Canadian medical tourists regarding the use of an information sheet to address this knowledge gap and raise awareness of the safety and ethical concerns related to medical tourism. Results According to feedback provided in interviews with former Canadian medical tourists, the majority of participants responded positively to the information sheet and indicated that this document prompted them to engage in further consideration of these issues. Participants indicated some frustration after reading the information sheet regarding a lack of know-how in terms of learning more about the concerns discussed in the document and changing their decision-making. This frustration was due to participants’ desperation for medical care, a topic which participants frequently discussed regarding ethical concerns related to health care provision. Conclusions The overall perceptions of former medical tourists indicate that an information sheet may promote further consideration of ethical concerns of medical tourism. However, given that these interviews were performed with former medical tourists, it remains unknown whether such a document might impact upon the decision-making of prospective medical tourists. Furthermore, participants indicated a need for an additional tool such as a website for continued discussion about these concerns. As such, along with dissemination of the information sheet

  15. Promoting social responsibility amongst health care users: medical tourists' perspectives on an information sheet regarding ethical concerns in medical tourism.

    Science.gov (United States)

    Adams, Krystyna; Snyder, Jeremy; Crooks, Valorie A; Johnston, Rory

    2013-12-06

    Medical tourists, persons that travel across international borders with the intention to access non-emergency medical care, may not be adequately informed of safety and ethical concerns related to the practice of medical tourism. Researchers indicate that the sources of information frequently used by medical tourists during their decision-making process may be biased and/or lack comprehensive information regarding individual safety and treatment outcomes, as well as potential impacts of the medical tourism industry on third parties. This paper explores the feedback from former Canadian medical tourists regarding the use of an information sheet to address this knowledge gap and raise awareness of the safety and ethical concerns related to medical tourism. According to feedback provided in interviews with former Canadian medical tourists, the majority of participants responded positively to the information sheet and indicated that this document prompted them to engage in further consideration of these issues. Participants indicated some frustration after reading the information sheet regarding a lack of know-how in terms of learning more about the concerns discussed in the document and changing their decision-making. This frustration was due to participants' desperation for medical care, a topic which participants frequently discussed regarding ethical concerns related to health care provision. The overall perceptions of former medical tourists indicate that an information sheet may promote further consideration of ethical concerns of medical tourism. However, given that these interviews were performed with former medical tourists, it remains unknown whether such a document might impact upon the decision-making of prospective medical tourists. Furthermore, participants indicated a need for an additional tool such as a website for continued discussion about these concerns. As such, along with dissemination of the information sheet, future research implications should

  16. Objective Evaluation in an Online Geographic Information System Certificate Program

    Directory of Open Access Journals (Sweden)

    Scott L. WALKER

    2005-01-01

    Full Text Available Objective Evaluation in an Online Geographic Information System Certificate Program Asst. Professor. Dr. Scott L. WALKER Texas State University-San Marcos San Marcos, Texas, USA ABSTRACT Departmental decisions regarding distance education programs can be subject to subjective decision-making processes influenced by external factors such as strong faculty opinions or pressure to increase student enrolment. This paper outlines an evaluation of a departmental distance-education program. The evaluation utilized several methods that strived to inject objectivity in evaluation and subsequent decision-making. A rapid multi-modal approach included evaluation methods of (1 considering the online psychosocial learning environment, (2 content analyses comparing the online version of classes to face-to-face versions, (3 cost comparisons in online vs. face-to-face classes, (4 student outcomes, (5 student retention, and (6 benchmarking. These approaches offer opportunities for departmental administrators and decision-making committees to make judgments informed by facts rather than being influenced by the emotions, beliefs, or opinions of organizational dynamics.

  17. ANALYSIS OF TRAIN SHEET IN THE INFORMATION SYSTEM OF JSC «UKRZALIZNYTSIA»: PERSPECTIVE

    Directory of Open Access Journals (Sweden)

    S. M. Ovcharenko

    2016-04-01

    Full Text Available Purpose. The system of train sheet analysis (TSA in the information system of JSC «Ukrzaliznytsia» provides work with passenger and suburban trains and has considerable potential. Therefore it is necessary to establish the prospects of development of the system. Methodology. Departments’ setup and the train delay causes should be carried out at every station and span, where such delays took place. This requires the fixation of condition deviations of infrastructure from normal and other adverse factors. In the sector of freight transportations the train schedule analysis is insufficient, since this analysis does not account for deviations from the terms of delivery. Therefore it also is necessary to analyze the delivery graphs. The basis for monitoring the cargo delivery is the method of control time points (CTP of technological operations performed with cargo at railway stations. On the basis of CTP to assess the quality of the transport process one should calculate the values of the analysis of cargo delivery schedule (performance level of the cargo delivery schedule, the coefficient of ahead of schedule/delay delivery. Findings. The article proposes to develop the system TSA using the input and display of the train delay causes on-line by transportation service employees, expansion of statistical databases and processing of the input delay causes during its calculation train sheet analysis of freight trains and quality assessment of the delivery schedule fulfillment. It is also appropriate before the new operator companies had appeared to make changes in the instructions TSCHU-TSD-0002 on the list of departments, which include delayed trains, by adding «the department» «The fault of operator companies» and corresponding causes of delays. Originality. The scheme of automated TSA in the information system of JSC «Ukrzaliznytsia» was improved. The author proposes to determine the cargo delivery quality on the certain polygon using the

  18. Transmitting information of an object behind the obstacle to infinity

    Science.gov (United States)

    Xu, Bai Bing; Jiang, Wei Xiang; Meng, Ling Ling; Cui, Tie Jun

    2015-08-01

    We propose an illusion device that transforms a metallic cylinder into a Luneburg lens by using transformation optics. Such a transformed focusing lens guides electromagnetic waves to propagate around the central metallic cylinder smoothly and be focused on one spot, and thus the information of an object behind the obstacle can be transmitted to infinity. In order to realize the required-anisotropic parameters with high permittivity and low permeability, we design embedded split-ring resonators (SRRs) to increase the permittivity of the traditional SRR structures. In experiments, we fabricate and measure the transformed lens, and the tested results agree well with the numerical simulations and theoretical predictions. The proposed transformation lens can mimic some properties of Einstein gravitational lens because their wave propagation behaviors are very similar.

  19. Accounting-information support investment in object of tourism industry

    Directory of Open Access Journals (Sweden)

    Ya.D. Krupka

    2015-06-01

    Full Text Available The article reveals the peculiarities of investments in tourism, their financial support through various sources. Given the branching system of travel, and additional related services offered by the author, each of the objects viewed as an investment project which, in turn, provides investment and obtaining from them certain benefits. In the article the system of investment projects, including the relationship of forms of investment (own cash and property investments of investors, credit and other borrowed resources, funds from sponsors and donations and the effects of investment (profit from operations, related income, social benefits for citizens and other benefits for society. Given the fact that every project goes through several stages since its launch and completion stages of submitted investment projects include the following phases: pre, investment process and control the results and return on capital investment projects under operation. The scheme of the project life cycle, which provided a way out of the project, corresponding interpretation investing activities international and national accounting standards and financial reporting. In this paper, special attention is paid to the rehabilitation of tourist visits, keeping investments in them, as well as an attempt to give an objective assessment of the effectiveness of such investments on the basis of accounting information.

  20. The Object Event Calculus and Temporal Geographic Information Systems

    National Research Council Canada - National Science Library

    Schmidt, Thomas

    2003-01-01

    .... A brief review of temporal issues as applied to object-oriented databases is supplied. In our approach, the Event Calculus is used to provide a formalism that avoids the question of object timestamping by not applying time to objects...

  1. Object Recognition via Information-Theoretic Measures/Metrics

    National Research Council Canada - National Science Library

    Repperger, Daniel W; Pinkus, Alan R; Skipper, Julie A; Schrider, Christian D

    2006-01-01

    .... In aerial military images, objects with different orientation can be reasonably approximated by a single identification signature consisting of the average histogram of the object under rotations...

  2. The Reviewing of Object Files: Object-Specific Integration of Information.

    Science.gov (United States)

    Kahneman, Daniel; And Others

    1992-01-01

    Seven experiments involving a total of 203 college students explored a form of object-specific priming and established a robust object-specific benefit that indicates that a new stimulus will be named faster if it physically matches a previous stimulus seen as part of the same perceptual object. (SLD)

  3. The FRJ 1 reactor (MERLIN) at Juelich, F.R. Germany and associated hot cell facilities. Information sheets

    International Nuclear Information System (INIS)

    Hardt, P. von der; Roettger, H.

    1981-01-01

    Technical information is given on the FRJ 1 reactor and associated hot cell facilities, with the main emphasis on experimental irradiation facilities, specialized irradiation devices (loops and capsules) and possibilities for post-irradiation examinations of samples. The information is presented in the form of eight information sheets under the headings: main characteristics of the reactor; utilization and specialization of the reactor; experimental facilities; neutron spectra; main characteristics of specialized irradiation devices; main characteristics of hot cell facilities; equipment and techniques available for post-irradiation examinations; utilization and specialization of the hot cell facilities

  4. The FR 2 reactor at Karlsruhe, F.R. Germany and associated hot cell facilities. Information sheets

    International Nuclear Information System (INIS)

    Hardt, P. von der; Roettger, H.

    1981-01-01

    Technical information is given on the FR 2 reactor and associated hot cell facilities, specialized irradiation devices (loops and capsules) and possibilities for post-irradiation examinations of samples. The information is presented in the form of eight information sheets under the headings: main characteristics of the reactor; utilization and specialization of the reactor; experimental facilities; neutron spectra; main characteristics of specialized irradiation devices; main characteristics of hot cell facilities; equipment and techniques available for post-irradiation examinations; utilization and specialization of the hot cell facilities

  5. Design of Object-based Information System Prototype

    OpenAIRE

    Suhyeon Yoo; Sumi Shin; Hyesun Kim

    2014-01-01

    Researchers who use science and technology information were found to ask an information service in which they can excerpt the contents they needed, rather than using the information at article level. In this study, we micronized the contents of scholarly articles into text, image, and table and then constructed a micro-content DB to design a new information system prototype based on this micro-content. After designing the prototype, we performed usability test for this prototype so as to conf...

  6. A JBI Information Object Engineering Environment Utilizing Metadata Fragments for Refining Searches on Semantically-Related Object Types

    National Research Council Canada - National Science Library

    Harlow, Felicia N

    2005-01-01

    .... This enhancement will improve the ability of JBI users to create and store IO type schemas, and query and subscribe to information objects, which may be semantically related by their inclusion...

  7. Development of a check sheet for collecting information necessary for occupational safety and health activities and building relevant systems in overseas business places.

    Science.gov (United States)

    Kajiki, Shigeyuki; Kobayashi, Yuichi; Uehara, Masamichi; Nakanishi, Shigemoto; Mori, Koji

    2016-06-07

    This study aimed to develop an information gathering check sheet to efficiently collect information necessary for Japanese companies to build global occupational safety and health management systems in overseas business places. The study group consisted of 2 researchers with occupational physician careers in a foreign-affiliated company in Japan and 3 supervising occupational physicians who were engaged in occupational safety and health activities in overseas business places. After investigating information and sources of information necessary for implementing occupational safety and health activities and building relevant systems, we conducted information acquisition using an information gathering check sheet in the field, by visiting 10 regions in 5 countries (first phase). The accuracy of the information acquired and the appropriateness of the information sources were then verified in study group meetings to improve the information gathering check sheet. Next, the improved information gathering check sheet was used in another setting (3 regions in 1 country) to confirm its efficacy (second phase), and the information gathering check sheet was thereby completed. The information gathering check sheet was composed of 9 major items (basic information on the local business place, safety and health overview, safety and health systems, safety and health staff, planning/implementation/evaluation/improvement, safety and health activities, laws and administrative organs, local medical care systems and public health, and medical support for resident personnel) and 61 medium items. We relied on the following eight information sources: the internet, company (local business place and head office in Japan), embassy/consulate, ISO certification body, university or other educational institutions, and medical institutions (aimed at Japanese people or at local workers). Through multiple study group meetings and a two-phased field survey (13 regions in 6 countries), an information

  8. Information as Object of Computer Science in Maritime Transport

    Directory of Open Access Journals (Sweden)

    Utureanu Simona

    2017-01-01

    The use of Information Technology infrastructures and the Internet, in addition to economic, social and political benefits, may also lead to tensions. The issue of cyber security can be addressed by promoting international maritime cyber security interests in international alliances.

  9. Objectivity

    CERN Document Server

    Daston, Lorraine

    2010-01-01

    Objectivity has a history, and it is full of surprises. In Objectivity, Lorraine Daston and Peter Galison chart the emergence of objectivity in the mid-nineteenth-century sciences--and show how the concept differs from its alternatives, truth-to-nature and trained judgment. This is a story of lofty epistemic ideals fused with workaday practices in the making of scientific images. From the eighteenth through the early twenty-first centuries, the images that reveal the deepest commitments of the empirical sciences--from anatomy to crystallography--are those featured in scientific atlases, the compendia that teach practitioners what is worth looking at and how to look at it. Galison and Daston use atlas images to uncover a hidden history of scientific objectivity and its rivals. Whether an atlas maker idealizes an image to capture the essentials in the name of truth-to-nature or refuses to erase even the most incidental detail in the name of objectivity or highlights patterns in the name of trained judgment is a...

  10. The use of health related quality of life data to produce information sheets for patients with head and neck cancer.

    Science.gov (United States)

    Rogers, S N; Hogg, E S; Cheung, W K A; Lai, L K L; Jassal, P; Lowe, D

    2015-07-01

    Health related quality of life information gives patients and carers an indication of how they will be affected following treatment. Such knowledge can promote realistic expectations and help patients come to terms with their outcome. The aim of this paper is to describe the background development of patient information sheets produced at our unit. The data were compiled using a common head and neck cancer specific quality of life questionnaire (University of Washington Quality of Life [UW-QOL]). There are 12 domains comprising activity, appearance, anxiety, chewing, mood, pain, recreation, saliva, shoulder, speech, swallowing and taste. The data were collected over 19 years at our unit and focus on follow-up records at around 2 years as this gives a good indication of health related quality of life in survivorship. UW-QOL questionnaires were available from 1,511 patients treated following primary diagnosis of head and neck cancer, and there were 24 subgroups based on cancer site, stage and treatment. There were 2 other subgroups: 132 having transoral laser resection and 176 having laryngectomy. The patient and carer research forum helped to design the information sheets, which display overall quality of life, percentages with 'good' outcome and 'significant problem' by domain, and the most important domains. Three examples are included in this paper: early stage oral cancer treated by surgery alone, early laryngeal cancer treated by surgery alone, and late stage oropharyngeal cancer treated by surgery and postoperative radiotherapy. All 26 subgroup information sheets are available in booklet form and on the internet. How the surgical community best utilises this type of resource needs further research.

  11. Do we have moral duties towards information objects?

    NARCIS (Netherlands)

    Brey, Philip A.E.

    2008-01-01

    In this paper, a critique will be developed and an alternative proposed to Luciano Floridi’s approach to Information Ethics (IE). IE is a macroethical theory that is to both serve as a foundation for computer ethics and to guide our overall moral attitude towards the world. The central claims of IE

  12. Advanced information science and object-oriented technology for information management applications

    Energy Technology Data Exchange (ETDEWEB)

    Hummel, J.R.; Swietlik, C.E.

    1996-10-01

    The role of the military has been undergoing rapid change since the fall of the Berlin Wall. The kinds of missions the US military has been asked to participate in have often fallen into the category of {open_quotes}Military Operations Other Than War{close_quotes} and those involving military responses have been more of a surgical nature directed against different kinds of threats, like rogue states or in response to terrorist actions. As a result, the requirements on the military planner and analyst have also had to change dramatically. For example, preparing response options now requires rapid turnaround and a highly flexible simulation capability. This in turn requires that the planner or analyst have access to sophisticated information science and simulation technologies. In this paper, we shall discuss how advanced information science and object-oriented technologies can be used in advanced information management applications. We shall also discuss how these technologies and tools can be applied to DoD applications by presenting examples with a system developed at Argonne, the Dynamic Information Architecture System (DIAS). DIAS has been developed to exploit advanced information science and simulation technologies to provide tools for future planners and analysts.

  13. Effects of Objectives and Information on Managerial Decisions and Profitability

    OpenAIRE

    JS Armstrong; Fred Collopy

    2004-01-01

    Managers are often advised, 'beat your competitors,' which sometimes contrasts with the advice, 'do the best for your firm.' This may lead managers to focus on comparative measures such as market share. Drawing on game theory, the authors hypothesize that managers are competitor oriented under certain conditions, in particular, when they are provided with information about competitors' performance. Empirical studies lead to the additional hypothesis that a competitor orientation is detrimenta...

  14. Cost Information – an Objective Necessity in Optimizing Decision Making

    OpenAIRE

    Petre Mihaela – Cosmina; Petroianu Grazia - Oana

    2012-01-01

    An overall growth can be registered at macro and micro level without achieving a development and this only under conditions of continuous improvement methods and techniques of organization and management within the unit. Cost and cost information play an important role being considered and recognized as useful and effective tools to reach any leader. They have features such as multiple facets to facilitate continuous improvement towards business unit. Cost awareness represents a decisive fact...

  15. CADMIO: computer aided design for medical information objects.

    Science.gov (United States)

    Minarelli, D V; Ferri, F; Pisanelli, D M; Ricci, F L; Tittarelli, F

    1995-01-01

    The growth of the computational capability and the tools of graphic software is nowadays available in an integrated manner into the development environments, thus permitting the realization of tool kits capable of handling information that is complex and of different kinds such as the typical medical information. This has given a great impulse to the creation of electronic medical folders joining together with new and stimulating functionality with respect to the usual paper document [1]. In the present work, we propose a tool capable of defining a multimedia electronic medical folder and representing its architecture through a layout that is formed on the basis of the particular data types to be handled. This tool is capable of providing an integrated view of data that, even though they are close in cognitive sense, are often stored and represented apart in the practice. Different approaches to the browsing feature are giving within the system, thus the user can personalize the way of viewing the information stored into the folder or can let the system guide the browsing.

  16. Objective identification of informative wavelength regions in galaxy spectra

    Energy Technology Data Exchange (ETDEWEB)

    Yip, Ching-Wa; Szalay, Alexander S.; Budavári, Tamás; Wyse, Rosemary F. G. [Department of Physics and Astronomy, The Johns Hopkins University, 3701 San Martin Drive, Baltimore, MD 21218 (United States); Mahoney, Michael W. [Department of Mathematics, Stanford University, Stanford, CA 94305 (United States); Csabai, István; Dobos, Laszlo, E-mail: cwyip@pha.jhu.edu, E-mail: szalay@jhu.edu, E-mail: mmahoney@cs.stanford.edu [Department of Physics of Complex Systems, Eötvös Loránd University, H-1117 Budapest (Hungary)

    2014-05-01

    Understanding the diversity in spectra is the key to determining the physical parameters of galaxies. The optical spectra of galaxies are highly convoluted with continuum and lines that are potentially sensitive to different physical parameters. Defining the wavelength regions of interest is therefore an important question. In this work, we identify informative wavelength regions in a single-burst stellar population model using the CUR Matrix Decomposition. Simulating the Lick/IDS spectrograph configuration, we recover the widely used D {sub n}(4000), Hβ, and Hδ {sub A} to be most informative. Simulating the Sloan Digital Sky Survey spectrograph configuration with a wavelength range 3450-8350 Å and a model-limited spectral resolution of 3 Å, the most informative regions are: first region—the 4000 Å break and the Hδ line; second region—the Fe-like indices; third region—the Hβ line; and fourth region—the G band and the Hγ line. A principal component analysis on the first region shows that the first eigenspectrum tells primarily the stellar age, the second eigenspectrum is related to the age-metallicity degeneracy, and the third eigenspectrum shows an anti-correlation between the strengths of the Balmer and the Ca K and H absorptions. The regions can be used to determine the stellar age and metallicity in early-type galaxies that have solar abundance ratios, no dust, and a single-burst star formation history. The region identification method can be applied to any set of spectra of the user's interest, so that we eliminate the need for a common, fixed-resolution index system. We discuss future directions in extending the current analysis to late-type galaxies. ASCII formatted tables of the regional eigenspectra are available.

  17. Vitamin and Mineral Supplement Fact Sheets

    Science.gov (United States)

    ... website Submit Search NIH Office of Dietary Supplements Vitamin and Mineral Supplement Fact Sheets Search the list ... Supplements: Background Information Botanical Dietary Supplements: Background Information Vitamin and Mineral Fact Sheets Botanical Supplement Fact Sheets ...

  18. Fuels planning: science synthesis and integration; social issues fact sheet 02: Developing personal responsibility for fuels reduction: Types of information to encourage proactive behavior

    Science.gov (United States)

    Rocky Mountain Research Station USDA Forest Service

    2004-01-01

    Fuels management responsibilities may include providing local property owners with the information for taking responsibility for reducing fuels on their land. This fact sheet discusses three different types of information that may be useful in programs to engage property owners in fuel reduction activities.

  19. An Object-Oriented Information Model for Policy-based Management of Distributed Applications

    NARCIS (Netherlands)

    Diaz, G.; Gay, V.C.J.; Horlait, E.; Hamza, M.H.

    2002-01-01

    This paper presents an object-oriented information model to support a policy-based management for distributed multimedia applications. The information base contains application-level information about the users, the applications, and their profile. Our Information model is described in details and

  20. Difficulties in using Material Safety Data Sheets to analyse occupational exposures to contact allergens

    DEFF Research Database (Denmark)

    Friis, Ulrik F; Menné, Torkil; Flyvholm, Mari-Ann

    2015-01-01

    BACKGROUND: Information on the occurrence of contact allergens and irritants is crucial for the diagnosis of occupational contact dermatitis. Material Safety Data Sheets (MSDS) are important sources of information concerning exposures in the workplace. OBJECTIVE: From a medical viewpoint...

  1. Color-Function Categories that Prime Infants to Use Color Information in an Object Individuation Task

    Science.gov (United States)

    Wilcox, Teresa; Woods, Rebecca; Chapa, Catherine

    2008-01-01

    There is evidence for developmental hierarchies in the type of information to which infants attend when reasoning about objects. Investigators have questioned the origin of these hierarchies and how infants come to identify new sources of information when reasoning about objects. The goal of the present experiments was to shed light on this debate…

  2. Resource Information and Forecasting Group; Electricity, Resources, & Building Systems Integration (ERBSI) (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2009-11-01

    Researchers in the Resource Information and Forecasting group at NREL provide scientific, engineering, and analytical expertise to help characterize renewable energy resources and facilitate the integration of these clean energy sources into the electricity grid.

  3. 77 FR 69548 - Proposed Information Collection (Agent Orange Registry Code Sheet); Comment Request

    Science.gov (United States)

    2012-11-19

    ... information contained in AOR to be able to notify Vietnam era veterans who served in the Republic of Vietnam... Gulf War Veterans Health Registry. Registry examination is provided to veterans who served in Korea in...

  4. Creation of integrated information model of 'Ukryttia' object premises condition to support the works

    International Nuclear Information System (INIS)

    Postil, S.D.; Ermolenko, A.I.; Ivanov, V.V.; Kotlyarov, V.T.

    2002-01-01

    A technology for creation of integrated information model of 'Ukryttia' Object premises conditions was developed on the basis of geoinformation system AutoCad. DB Access and instrumental utility 3D MAX. Information models and database for conditions of 'Ukryttia' object's premises located between 0.000 and 67.000 marks in axes 41-52, row G-T, were created. Using integrated information model of 'Ukryttia' object premises conditions, 3D surface distribution of radiation field in the object premises on level 0.000 has been received. It is revealed that maximum values of radiation field are concentrated over the clusters of fuel-containing materials

  5. An object model for genome information at all levels of resolution

    Energy Technology Data Exchange (ETDEWEB)

    Honda, S.; Parrott, N.W.; Smith, R.; Lawrence, C.

    1993-12-31

    An object model for genome data at all levels of resolution is described. The model was derived by considering the requirements for representing genome related objects in three application domains: genome maps, large-scale DNA sequencing, and exploring functional information in gene and protein sequences. The methodology used for the object-oriented analysis is also described.

  6. Comparing infants' use of featural and spatiotemporal information when individuating objects in an event monitoring design

    DEFF Research Database (Denmark)

    Krøjgaard, Peter

    . The results obtained using this design reveal that infants are more successful using spatiotemporal object information than when using featural information. However, recent studies using the less cognitively demanding event monitoring design have revealed that even younger infants are capable of object...... in the present series of experiments in which infants' use of spatiotemporal and featural information is compared directly using the less demanding event monitoring design. The results are discussed in relation to existing empirical evidence......., to what extent infants rely on spatiotemporal or featural object information when individuating objects is currently under debate. Hitherto, infants' use of spatiotemporal and featural object information has only been compared directly using the rather cognitively demanding event mapping design...

  7. [To what extent do reviewers of multiple-choice questions need to be trained? A comparison between handing out information sheets and brief workshop sessions].

    Science.gov (United States)

    Öchsner, Wolfgang; Böckers, Anja

    2016-01-01

    A competent review process is crucial to ensure the quality of multiple-choice (MC) questions. However, the acquisition of reviewing skills should not cause any unnecessary additional burden for a medical staff that is already facing heavy workloads. 100 MC questions, for which an expert review existed, were presented to 12 novices. In advance, six participants received a specific information sheet covering critical information for high-calibre review; the other six participants attended a 2.5-hour workshop covering the same information. The review results of both groups were analysed with a licensed version of the IBM software SPSS 19.0 (SPSS Inc., Chicago, IL). The results of the workshop group were distinctly closer to the experts' results (gold standard) than those of the information sheet group. For the quantitatively important category of medium quality MC questions, the results of the workshop group did not significantly differ from the experts' results. In the information sheet group the results were significantly poorer than the experts', regardless of the quality of the questions. Distributing specific information sheets to MC question reviewers is not sufficient for ensuring the quality of the review so that - regardless of the increased effort involved - a recommendation to conduct specific workshops must be made. Copyright © 2014. Published by Elsevier GmbH.

  8. Complex method to calculate objective assessments of information systems protection to improve expert assessments reliability

    Science.gov (United States)

    Abdenov, A. Zh; Trushin, V. A.; Abdenova, G. A.

    2018-01-01

    The paper considers the questions of filling the relevant SIEM nodes based on calculations of objective assessments in order to improve the reliability of subjective expert assessments. The proposed methodology is necessary for the most accurate security risk assessment of information systems. This technique is also intended for the purpose of establishing real-time operational information protection in the enterprise information systems. Risk calculations are based on objective estimates of the adverse events implementation probabilities, predictions of the damage magnitude from information security violations. Calculations of objective assessments are necessary to increase the reliability of the proposed expert assessments.

  9. A Novel Abandoned Object Detection System Based on Three-Dimensional Image Information

    Directory of Open Access Journals (Sweden)

    Yiliang Zeng

    2015-03-01

    Full Text Available A new idea of an abandoned object detection system for road traffic surveillance systems based on three-dimensional image information is proposed in this paper to prevent traffic accidents. A novel Binocular Information Reconstruction and Recognition (BIRR algorithm is presented to implement the new idea. As initial detection, suspected abandoned objects are detected by the proposed static foreground region segmentation algorithm based on surveillance video from a monocular camera. After detection of suspected abandoned objects, three-dimensional (3D information of the suspected abandoned object is reconstructed by the proposed theory about 3D object information reconstruction with images from a binocular camera. To determine whether the detected object is hazardous to normal road traffic, road plane equation and height of suspected-abandoned object are calculated based on the three-dimensional information. Experimental results show that this system implements fast detection of abandoned objects and this abandoned object system can be used for road traffic monitoring and public area surveillance.

  10. Decontamination sheet

    International Nuclear Information System (INIS)

    Hirose, Emiko; Kanesaki, Ken.

    1995-01-01

    The decontamination sheet of the present invention is formed by applying an adhesive on one surface of a polymer sheet and releasably appending a plurality of curing sheets. In addition, perforated lines are formed on the sheet, and a decontaminating agent is incorporated in the adhesive. This can reduce the number of curing operation steps when a plurality steps of operations for radiation decontamination equipments are performed, and further, the amount of wastes of the cured sheets, and operator's exposure are reduced, as well as an efficiency of the curing operation can be improved, and propagation of contamination can be prevented. (T.M.)

  11. Deconstructing visual scenes in cortex: gradients of object and spatial layout information.

    Science.gov (United States)

    Harel, Assaf; Kravitz, Dwight J; Baker, Chris I

    2013-04-01

    Real-world visual scenes are complex cluttered, and heterogeneous stimuli engaging scene- and object-selective cortical regions including parahippocampal place area (PPA), retrosplenial complex (RSC), and lateral occipital complex (LOC). To understand the unique contribution of each region to distributed scene representations, we generated predictions based on a neuroanatomical framework adapted from monkey and tested them using minimal scenes in which we independently manipulated both spatial layout (open, closed, and gradient) and object content (furniture, e.g., bed, dresser). Commensurate with its strong connectivity with posterior parietal cortex, RSC evidenced strong spatial layout information but no object information, and its response was not even modulated by object presence. In contrast, LOC, which lies within the ventral visual pathway, contained strong object information but no background information. Finally, PPA, which is connected with both the dorsal and the ventral visual pathway, showed information about both objects and spatial backgrounds and was sensitive to the presence or absence of either. These results suggest that 1) LOC, PPA, and RSC have distinct representations, emphasizing different aspects of scenes, 2) the specific representations in each region are predictable from their patterns of connectivity, and 3) PPA combines both spatial layout and object information as predicted by connectivity.

  12. Dynamic information processing states revealed through neurocognitive models of object semantics

    Science.gov (United States)

    Clarke, Alex

    2015-01-01

    Recognising objects relies on highly dynamic, interactive brain networks to process multiple aspects of object information. To fully understand how different forms of information about objects are represented and processed in the brain requires a neurocognitive account of visual object recognition that combines a detailed cognitive model of semantic knowledge with a neurobiological model of visual object processing. Here we ask how specific cognitive factors are instantiated in our mental processes and how they dynamically evolve over time. We suggest that coarse semantic information, based on generic shared semantic knowledge, is rapidly extracted from visual inputs and is sufficient to drive rapid category decisions. Subsequent recurrent neural activity between the anterior temporal lobe and posterior fusiform supports the formation of object-specific semantic representations – a conjunctive process primarily driven by the perirhinal cortex. These object-specific representations require the integration of shared and distinguishing object properties and support the unique recognition of objects. We conclude that a valuable way of understanding the cognitive activity of the brain is though testing the relationship between specific cognitive measures and dynamic neural activity. This kind of approach allows us to move towards uncovering the information processing states of the brain and how they evolve over time. PMID:25745632

  13. ACCOUNTING INFORMATION SYSTEMS: AN APPROACH FOCUSED ON OBJECTS WITH INTELLIGENT AGENTS

    Directory of Open Access Journals (Sweden)

    Marcelo Botelho da Costa Moraes

    2010-01-01

    Full Text Available Accounting aims at the treatment of information related to economic events within organizations. In order to do so, the double entry method is used (debt and credit accounting, which only considers monetary variations. With the development of information technologies, accounting information systems are born. In the 1980’s, the REA model (economic Resources, economic Events and economic Agents is created, which focuses on accounting information records, based on the association of economic resources, economic events and economic agents. The objective of this work is to demonstrate an object-oriented modeling with intelligent agents use, for information development and analysis focused on users. The proposed model is also analyzed according to accounting information quality, necessary for accounting information users, capable to comply with the needs of different user groups, with advantages in applications.

  14. Modeling of information on the impact of mining exploitation on bridge objects in BIM

    Science.gov (United States)

    Bętkowski, Piotr

    2018-04-01

    The article discusses the advantages of BIM (Building Information Modeling) technology in the management of bridge infrastructure on mining areas. The article shows the problems with information flow in the case of bridge objects located on mining areas and the advantages of proper information management, e.g. the possibility of automatic monitoring of structures, improvement of safety, optimization of maintenance activities, cost reduction of damage removal and preventive actions, improvement of atmosphere for mining exploitation, improvement of the relationship between the manager of the bridge and the mine. Traditional model of managing bridge objects on mining areas has many disadvantages, which are discussed in this article. These disadvantages include among others: duplication of information about the object, lack of correlation in investments due to lack of information flow between bridge manager and mine, limited assessment possibilities of damage propagation on technical condition and construction resistance to mining influences.

  15. Is Seeing Believing? Identifying Aspects of Informative Videos that Indicate Objectivity

    NARCIS (Netherlands)

    H.M. Boots-Blankers (Helen)

    2017-01-01

    textabstractInformation in online videos can be misleading and unreliable. Video users tend to select videos with misleading information (Butler, 2013). To facilitate video users in their selection of videos they need an objectivity measure (Palumbo, 2012). We propose thirteen aspects of video that

  16. Creation of a common information system on the Republic of Kazakhstan radiation hazardous objects

    International Nuclear Information System (INIS)

    Kadyrzhanov, K.K.; Kuterbekov, K.A.; Lukashenko, S.N.; Morenko, V.S.; Glushchenko, V.N.

    2005-01-01

    Works on creation of a common information system on the Republic of Kazakhstan territory radiation hazardous objects for providing of radiation situation control and stewardship decision making under nature-conservative measures conducting are considered. The information system is forming on the base of up-to-date GIS system - ArcGIS - and incorporates two databases - geographical and attributive

  17. A Novel Object Tracking Algorithm Based on Compressed Sensing and Entropy of Information

    Directory of Open Access Journals (Sweden)

    Ding Ma

    2015-01-01

    Full Text Available Object tracking has always been a hot research topic in the field of computer vision; its purpose is to track objects with specific characteristics or representation and estimate the information of objects such as their locations, sizes, and rotation angles in the current frame. Object tracking in complex scenes will usually encounter various sorts of challenges, such as location change, dimension change, illumination change, perception change, and occlusion. This paper proposed a novel object tracking algorithm based on compressed sensing and information entropy to address these challenges. First, objects are characterized by the Haar (Haar-like and ORB features. Second, the dimensions of computation space of the Haar and ORB features are effectively reduced through compressed sensing. Then the above-mentioned features are fused based on information entropy. Finally, in the particle filter framework, an object location was obtained by selecting candidate object locations in the current frame from the local context neighboring the optimal locations in the last frame. Our extensive experimental results demonstrated that this method was able to effectively address the challenges of perception change, illumination change, and large area occlusion, which made it achieve better performance than existing approaches such as MIL and CT.

  18. Object-oriented analysis and design for information systems Modeling with UML, OCL, IFML

    CERN Document Server

    Wazlawick, Raul Sidnei

    2014-01-01

    Object-Oriented Analysis and Design for Information Systems clearly explains real object-oriented programming in practice. Expert author Raul Sidnei Wazlawick explains concepts such as object responsibility, visibility and the real need for delegation in detail. The object-oriented code generated by using these concepts in a systematic way is concise, organized and reusable. The patterns and solutions presented in this book are based in research and industrial applications. You will come away with clarity regarding processes and use cases and a clear understand of how to expand a use case.

  19. MODELING OF TECHNICAL CHANNELS OF INFORMATION LEAKAGE AT DISTRIBUTED CONTROL OBJECTS

    Directory of Open Access Journals (Sweden)

    Aleksander Vladimirovich Karpov

    2018-05-01

    Full Text Available The significant increase in requirements for distributed control objects’ functioning can’t be realized only at the expense of the widening and strengthening of security control measures. The first step in ensuring the information security at such objects is the analysis of the conditions of their functioning and modeling of technical channels of information leakage. The development of models of such channels is essentially the only method of complete study of their opportunities and it is pointed toward receiving quantitative assessments of the safe operation of compound objects. The evaluation data are necessary to make a decision on the degree of the information security from a leak according to the current criterion. The existing models are developed for the standard concentrated objects and allow to evaluate the level of information security from a leak on each of channels separately, what involves the significant increase in the required protective resource and time of assessment of information security on an object in general. The article deals with a logical-and-probabilistic method of a security assessment of structurally-compound objects. The model of a security leak on the distributed control objects is cited as an example. It is recommended to use a software package of an automated structurally-logistical modeling of compound systems, which allows to evaluate risk of information leakage in the loudspeaker. A possibility of information leakage by technical channels is evaluated and such differential characteristics of the safe operation of the distributed control objects as positive and negative contributions of the initiating events and conditions, which cause a leak are calculated. Purpose. The aim is a quantitative assessment of data risk, which is necessary for justifying the rational composition of organizational and technical protection measures, as well as a variant of the structure of the information security system from a

  20. Abnormal dynamics of activation of object use information in apraxia: evidence from eyetracking

    Science.gov (United States)

    Lee, Chia-lin; Mirman, Daniel; Buxbaum, Laurel J.

    2014-01-01

    Action representations associated with object use may be incidentally activated during visual object processing, and the time course of such activations may be influenced by lexical-semantic context (e.g., Lee, Middleton, Mirman, Kalénine, & Buxbaum, 2012). In this study we used the “visual world” eye-tracking paradigm to examine whether a deficit in producing skilled object-use actions (apraxia) is associated with abnormalities in incidental activation of action information, and assessed the neuroanatomical substrates of any such deficits. Twenty left hemisphere stroke patients, ten of whom were apraxic, performed a task requiring identification of a named object in a visual display containing manipulation-related and unrelated distractor objects. Manipulation relationships among objects were not relevant to the identification task. Objects were cued with neutral (“S/he saw the….”), or action-relevant (“S/he used the….”) sentences. Non-apraxic participants looked at use-related non-target objects significantly more than at unrelated non-target objects when cued both by neutral and action-relevant sentences, indicating that action information is incidentally activated. In contrast, apraxic participants showed delayed activation of manipulation-based action information during object identification when cued by neutral sentences. The magnitude of delayed activation in the neutral sentence condition was reliably predicted by lower scores on a test of gesture production to viewed objects, as well as by lesion loci in the inferior parietal and posterior temporal lobes. However, when cued by a sentence containing an action verb, apraxic participants showed fixation patterns that were statistically indistinguishable from non-apraxic controls. In support of grounded theories of cognition, these results suggest that apraxia and temporal-parietal lesions may be associated with abnormalities in incidental activation of action information from objects. Further

  1. Manipulation of Unknown Objects to Improve the Grasp Quality Using Tactile Information.

    Science.gov (United States)

    Montaño, Andrés; Suárez, Raúl

    2018-05-03

    This work presents a novel and simple approach in the area of manipulation of unknown objects considering both geometric and mechanical constraints of the robotic hand. Starting with an initial blind grasp, our method improves the grasp quality through manipulation considering the three common goals of the manipulation process: improving the hand configuration, the grasp quality and the object positioning, and, at the same time, prevents the object from falling. Tactile feedback is used to obtain local information of the contacts between the fingertips and the object, and no additional exteroceptive feedback sources are considered in the approach. The main novelty of this work lies in the fact that the grasp optimization is performed on-line as a reactive procedure using the tactile and kinematic information obtained during the manipulation. Experimental results are shown to illustrate the efficiency of the approach.

  2. The application of the unified modeling language in object-oriented analysis of healthcare information systems.

    Science.gov (United States)

    Aggarwal, Vinod

    2002-10-01

    This paper concerns itself with the beneficial effects of the Unified Modeling Language (UML), a nonproprietary object modeling standard, in specifying, visualizing, constructing, documenting, and communicating the model of a healthcare information system from the user's perspective. The author outlines the process of object-oriented analysis (OOA) using the UML and illustrates this with healthcare examples to demonstrate the practicality of application of the UML by healthcare personnel to real-world information system problems. The UML will accelerate advanced uses of object-orientation such as reuse technology, resulting in significantly higher software productivity. The UML is also applicable in the context of a component paradigm that promises to enhance the capabilities of healthcare information systems and simplify their management and maintenance.

  3. Application of Bayesian Decision Theory Based on Prior Information in the Multi-Objective Optimization Problem

    Directory of Open Access Journals (Sweden)

    Xia Lei

    2010-12-01

    Full Text Available General multi-objective optimization methods are hard to obtain prior information, how to utilize prior information has been a challenge. This paper analyzes the characteristics of Bayesian decision-making based on maximum entropy principle and prior information, especially in case that how to effectively improve decision-making reliability in deficiency of reference samples. The paper exhibits effectiveness of the proposed method using the real application of multi-frequency offset estimation in distributed multiple-input multiple-output system. The simulation results demonstrate Bayesian decision-making based on prior information has better global searching capability when sampling data is deficient.

  4. Probabilistic information on object weight shapes force dynamics in a grip-lift task.

    Science.gov (United States)

    Trampenau, Leif; Kuhtz-Buschbeck, Johann P; van Eimeren, Thilo

    2015-06-01

    Advance information, such as object weight, size and texture, modifies predictive scaling of grip forces in a grip-lift task. Here, we examined the influence of probabilistic advance information about object weight. Fifteen healthy volunteers repeatedly grasped and lifted an object equipped with a force transducer between their thumb and index finger. Three clearly distinguishable object weights were used. Prior to each lift, the probabilities for the three object weights were given by a visual cue. We examined the effect of probabilistic pre-cues on grip and lift force dynamics. We expected predictive scaling of grip force parameters to follow predicted values calculated according to probabilistic contingencies of the cues. We observed that probabilistic cues systematically influenced peak grip and load force rates, as an index of predictive motor scaling. However, the effects of probabilistic cues on force rates were nonlinear, and anticipatory adaptations of the motor output generally seemed to overestimate high probabilities and underestimate low probabilities. These findings support the suggestion that anticipatory adaptations and force scaling of the motor system can integrate probabilistic information. However, probabilistic information seems to influence motor programs in a nonlinear fashion.

  5. Global ice sheet modeling

    International Nuclear Information System (INIS)

    Hughes, T.J.; Fastook, J.L.

    1994-05-01

    The University of Maine conducted this study for Pacific Northwest Laboratory (PNL) as part of a global climate modeling task for site characterization of the potential nuclear waste respository site at Yucca Mountain, NV. The purpose of the study was to develop a global ice sheet dynamics model that will forecast the three-dimensional configuration of global ice sheets for specific climate change scenarios. The objective of the third (final) year of the work was to produce ice sheet data for glaciation scenarios covering the next 100,000 years. This was accomplished using both the map-plane and flowband solutions of our time-dependent, finite-element gridpoint model. The theory and equations used to develop the ice sheet models are presented. Three future scenarios were simulated by the model and results are discussed

  6. Holding an object one is looking at : Kinesthetic information on the object's distance does not improve visual judgments of its size

    NARCIS (Netherlands)

    Brenner, Eli; Van Damme, Wim J.M.; Smeets, Jeroen B.J.

    1997-01-01

    Visual judgments of distance are often inaccurate. Nevertheless, information on distance must be procured if retinal image size is to be used to judge an object's dimensions. In the present study, we examined whether kinesthetic information about an object's distance - based on the posture of the

  7. A Vision-Based System for Object Identification and Information Retrieval in a Smart Home

    Science.gov (United States)

    Grech, Raphael; Monekosso, Dorothy; de Jager, Deon; Remagnino, Paolo

    This paper describes a hand held device developed to assist people to locate and retrieve information about objects in a home. The system developed is a standalone device to assist persons with memory impairments such as people suffering from Alzheimer's disease. A second application is object detection and localization for a mobile robot operating in an ambient assisted living environment. The device relies on computer vision techniques to locate a tagged object situated in the environment. The tag is a 2D color printed pattern with a detection range and a field of view such that the user may point from a distance of over 1 meter.

  8. Installing and Executing Information Object Analysis, Intent, Dissemination, and Enhancement (IOAIDE) and Its Dependencies

    Science.gov (United States)

    2017-02-01

    SUPPLEMENTARY NOTES 14. ABSTRACT Information Object Analysis, Intent, Dissemination, and Enhancement (IOAIDE) is a novel information framework developed...prototyping. It supports dynamic plugin of analysis modules, for either research or analysis tasks. The framework integrates multiple image processing...Requirements 2 3. Installing the Software for IOAIDE 2 3.1 Load ARL Software 2 3.2 Load ARL Applications 4 3.3 Load the DSPro Software 7 3.4 Update Java

  9. Methods of Information Subjects and Objects Interaction Rules Formalization in the Electronic Trading Platform System

    Directory of Open Access Journals (Sweden)

    Emma Emanuilova Yandybaeva

    2015-03-01

    Full Text Available The methods of information subjects and objects interaction rules formalization in the electronic trading platform system has been developed. They are based on mathematical model of mandatory role-based access control. As a result of the work we have defined set of user roles and constructed roles hierarchy. For the roles hierarchy restrictions have been imposed to ensure the safety of the information system.

  10. GASN sheets

    International Nuclear Information System (INIS)

    2013-12-01

    This document gathers around 50 detailed sheets which describe and present various aspects, data and information related to the nuclear sector or, more generally to energy. The following items are addressed: natural and artificial radioactive environment, evolution of energy needs in the world, radioactive wastes, which energy for France tomorrow, the consequences in France of the Chernobyl accident, ammunitions containing depleted uranium, processing and recycling of used nuclear fuel, transport of radioactive materials, seismic risk for the basic nuclear installations, radon, the precautionary principle, the issue of low doses, the EPR, the greenhouse effect, the Oklo nuclear reactors, ITER on the way towards fusion reactors, simulation and nuclear deterrence, crisis management in the nuclear field, does nuclear research put a break on the development of renewable energies by monopolizing funding, nuclear safety and security, the plutonium, generation IV reactors, comparison of different modes of electricity production, medical exposure to ionizing radiations, the control of nuclear activities, food preservation by ionization, photovoltaic solar collectors, the Polonium 210, the dismantling of nuclear installations, wind energy, desalination and nuclear reactors, from non-communication to transparency about nuclear safety, the Jules Horowitz reactor, CO 2 capture and storage, hydrogen, solar energy, the radium, the subcontractors of maintenance of the nuclear fleet, biomass, internal radio-contamination, epidemiological studies, submarine nuclear propulsion, sea energy, the Three Mile Island accident, the Chernobyl accident, the Fukushima accident, the nuclear after Fukushima

  11. Country Selection Model for Sustainable Construction Businesses Using Hybrid of Objective and Subjective Information

    Directory of Open Access Journals (Sweden)

    Kang-Wook Lee

    2017-05-01

    Full Text Available An important issue for international businesses and academia is selecting countries in which to expand in order to achieve entrepreneurial sustainability. This study develops a country selection model for sustainable construction businesses using both objective and subjective information. The objective information consists of 14 variables related to country risk and project performance in 32 countries over 25 years. This hybrid model applies subjective weighting from industrial experts to objective information using a fuzzy LinPreRa-based Analytic Hierarchy Process. The hybrid model yields a more accurate country selection compared to a purely objective information-based model in experienced countries. Interestingly, the hybrid model provides some different predictions with only subjective opinions in unexperienced countries, which implies that expert opinion is not always reliable. In addition, feedback from five experts in top international companies is used to validate the model’s completeness, effectiveness, generality, and applicability. The model is expected to aid decision makers in selecting better candidate countries that lead to sustainable business success.

  12. Humans use visual and remembered information about object location to plan pointing movements

    NARCIS (Netherlands)

    Brouwer, A.-M.; Knill, D.C.

    2009-01-01

    We investigated whether humans use a target's remembered location to plan reaching movements to targets according to the relative reliabilities of visual and remembered information. Using their index finger, subjects moved a virtual object from one side of a table to the other, and then went back to

  13. 47 CFR 73.3588 - Dismissal of petitions to deny or withdrawal of informal objections.

    Science.gov (United States)

    2010-10-01

    ... withdraw the petition to deny or the informal objection, either unilaterally or in exchange for financial...: (1) A certification that neither the petitioner nor its principals has received or will receive any... or promised; (3) An itemized accounting of the expenses for which it seeks reimbursement; and (4) The...

  14. 34 CFR 364.42 - What objectives and information must be included in the State plan?

    Science.gov (United States)

    2010-07-01

    ... 34 Education 2 2010-07-01 2010-07-01 false What objectives and information must be included in the State plan? 364.42 Section 364.42 Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF SPECIAL EDUCATION AND REHABILITATIVE SERVICES, DEPARTMENT OF EDUCATION STATE...

  15. Young Children's Use of Surface and Object Information in Drawings of Everyday Scenes.

    Science.gov (United States)

    Dillon, Moira R; Spelke, Elizabeth S

    2017-09-01

    Pictorial symbols such as photographs, drawings, and maps are ubiquitous in modern cultures. Nevertheless, it remains unclear how children relate these symbols to the scenes that they represent. The present work investigates 4-year-old children's (N = 144) sensitivity to extended surface layouts and objects when using drawings of a room to find locations in that room. Children used either extended surfaces or objects when interpreting drawings, but they did not combine these two types of information to disambiguate target locations. Moreover, children's evaluations of drawings depicting surfaces or objects did not align with their use of such information in those drawings. These findings suggest that pictures of all kinds serve as media in which children deploy symbolic spatial skills flexibly and automatically. © 2016 The Authors. Child Development © 2016 Society for Research in Child Development, Inc.

  16. Shadow detection of moving objects based on multisource information in Internet of things

    Science.gov (United States)

    Ma, Zhen; Zhang, De-gan; Chen, Jie; Hou, Yue-xian

    2017-05-01

    Moving object detection is an important part in intelligent video surveillance under the banner of Internet of things. The detection of moving target's shadow is also an important step in moving object detection. On the accuracy of shadow detection will affect the detection results of the object directly. Based on the variety of shadow detection method, we find that only using one feature can't make the result of detection accurately. Then we present a new method for shadow detection which contains colour information, the invariance of optical and texture feature. Through the comprehensive analysis of the detecting results of three kinds of information, the shadow was effectively determined. It gets ideal effect in the experiment when combining advantages of various methods.

  17. Looking at a contrast object before speaking boosts referential informativeness, but is not essential.

    Science.gov (United States)

    Davies, Catherine; Kreysa, Helene

    2017-07-01

    Variation in referential form has traditionally been accounted for by theoretical frameworks focusing on linguistic and discourse features. Despite the explosion of interest in eye tracking methods in psycholinguistics, the role of visual scanning behaviour in informative reference production is yet to be comprehensively investigated. Here we examine the relationship between speakers' fixations to relevant referents and the form of the referring expressions they produce. Overall, speakers were fully informative across simple and (to a lesser extent) more complex displays, providing appropriately modified referring expressions to enable their addressee to locate the target object. Analysis of contrast fixations revealed that looking at a contrast object boosts but is not essential for full informativeness. Contrast fixations which take place immediately before speaking provide the greatest boost. Informative referring expressions were also associated with later speech onsets than underinformative ones. Based on the finding that fixations during speech planning facilitate but do not fully predict informative referring, direct visual scanning is ruled out as a prerequisite for informativeness. Instead, pragmatic expectations of informativeness may play a more important role. Results are consistent with a goal-based link between eye movements and language processing, here applied for the first time to production processes. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Contralateral delay activity tracks object identity information in visual short term memory.

    Science.gov (United States)

    Gao, Zaifeng; Xu, Xiaotian; Chen, Zhibo; Yin, Jun; Shen, Mowei; Shui, Rende

    2011-08-11

    Previous studies suggested that ERP component contralateral delay activity (CDA) tracks the number of objects containing identity information stored in visual short term memory (VSTM). Later MEG and fMRI studies implied that its neural source lays in superior IPS. However, since the memorized stimuli in previous studies were displayed in distinct spatial locations, hence possibly CDA tracks the object-location information instead. Moreover, a recent study implied the activation in superior IPS reflected the location load. The current research thus explored whether CDA tracks the object-location load or the object-identity load, and its neural sources. Participants were asked to remember one color, four identical colors or four distinct colors. The four-identical-color condition was the critical one because it contains the same amount of identity information as that of one color while the same amount of location information as that of four distinct colors. To ensure the participants indeed selected four colors in the four-identical-color condition, we also split the participants into two groups (low- vs. high-capacity), analyzed late positive component (LPC) in the prefrontal area, and collected participant's subjective-report. Our results revealed that most of the participants selected four identical colors. Moreover, regardless of capacity-group, there was no difference on CDA between one color and four identical colors yet both were lower than 4 distinct colors. Besides, the source of CDA was located in the superior parietal lobule, which is very close to the superior IPS. These results support the statement that CDA tracks the object identity information in VSTM. Copyright © 2011 Elsevier B.V. All rights reserved.

  19. Neuronal encoding of object and distance information: A model simulation study on naturalistic optic flow processing

    Directory of Open Access Journals (Sweden)

    Patrick eHennig

    2012-03-01

    Full Text Available We developed a model of the input circuitry of the FD1 cell, an identified motion-sensitive interneuron in the blowfly’s visual system. The model circuit successfully reproduces the FD1 cell’s most conspicuous property: Its larger responses to objects than to spatially extended patterns. The model circuit also mimics the time-dependent responses of FD1 to dynamically complex naturalistic stimuli, shaped by the blowfly’s saccadic flight and gaze strategy: The FD1 responses are enhanced when, as a consequence of self-motion, a nearby object crosses the receptive field during intersaccadic intervals. Moreover, the model predicts that these object-induced responses are superimposed by pronounced pattern-dependent fluctuations during movements on virtual test flights in a three-dimensional environment with systematic modifications of the environmental patterns. Hence, the FD1 cell is predicted to detect not unambiguously objects defined by the spatial layout of the environment, but to be also sensitive to objects distinguished by textural features. These ambiguous detection abilities suggest an encoding of information about objects - irrespective of the features by which the objects are defined - by a population of cells, with the FD1 cell presumably playing a prominent role in such an ensemble.

  20. Persistent spatial information in the frontal eye field during object-based short-term memory.

    Science.gov (United States)

    Clark, Kelsey L; Noudoost, Behrad; Moore, Tirin

    2012-08-08

    Spatial attention is known to gate entry into visual short-term memory, and some evidence suggests that spatial signals may also play a role in binding features or protecting object representations during memory maintenance. To examine the persistence of spatial signals during object short-term memory, the activity of neurons in the frontal eye field (FEF) of macaque monkeys was recorded during an object-based delayed match-to-sample task. In this task, monkeys were trained to remember an object image over a brief delay, regardless of the locations of the sample or target presentation. FEF neurons exhibited visual, delay, and target period activity, including selectivity for sample location and target location. Delay period activity represented the sample location throughout the delay, despite the irrelevance of spatial information for successful task completion. Furthermore, neurons continued to encode sample position in a variant of the task in which the matching stimulus never appeared in their response field, confirming that FEF maintains sample location independent of subsequent behavioral relevance. FEF neurons also exhibited target-position-dependent anticipatory activity immediately before target onset, suggesting that monkeys predicted target position within blocks. These results show that FEF neurons maintain spatial information during short-term memory, even when that information is irrelevant for task performance.

  1. Efficient Cross-Modal Transfer of Shape Information in Visual and Haptic Object Categorization

    Directory of Open Access Journals (Sweden)

    Nina Gaissert

    2011-10-01

    Full Text Available Categorization has traditionally been studied in the visual domain with only a few studies focusing on the abilities of the haptic system in object categorization. During the first years of development, however, touch and vision are closely coupled in the exploratory procedures used by the infant to gather information about objects. Here, we investigate how well shape information can be transferred between those two modalities in a categorization task. Our stimuli consisted of amoeba-like objects that were parametrically morphed in well-defined steps. Participants explored the objects in a categorization task either visually or haptically. Interestingly, both modalities led to similar categorization behavior suggesting that similar shape processing might occur in vision and haptics. Next, participants received training on specific categories in one of the two modalities. As would be expected, training increased performance in the trained modality; however, we also found significant transfer of training to the other, untrained modality after only relatively few training trials. Taken together, our results demonstrate that complex shape information can be transferred efficiently across the two modalities, which speaks in favor of multisensory, higher-level representations of shape.

  2. An Upper Bound on Orbital Debris Collision Probability When Only One Object has Position Uncertainty Information

    Science.gov (United States)

    Frisbee, Joseph H., Jr.

    2015-01-01

    Upper bounds on high speed satellite collision probability, P (sub c), have been investigated. Previous methods assume an individual position error covariance matrix is available for each object. The two matrices being combined into a single, relative position error covariance matrix. Components of the combined error covariance are then varied to obtain a maximum P (sub c). If error covariance information for only one of the two objects was available, either some default shape has been used or nothing could be done. An alternative is presented that uses the known covariance information along with a critical value of the missing covariance to obtain an approximate but useful P (sub c) upper bound. There are various avenues along which an upper bound on the high speed satellite collision probability has been pursued. Typically, for the collision plane representation of the high speed collision probability problem, the predicted miss position in the collision plane is assumed fixed. Then the shape (aspect ratio of ellipse), the size (scaling of standard deviations) or the orientation (rotation of ellipse principal axes) of the combined position error ellipse is varied to obtain a maximum P (sub c). Regardless as to the exact details of the approach, previously presented methods all assume that an individual position error covariance matrix is available for each object and the two are combined into a single, relative position error covariance matrix. This combined position error covariance matrix is then modified according to the chosen scheme to arrive at a maximum P (sub c). But what if error covariance information for one of the two objects is not available? When error covariance information for one of the objects is not available the analyst has commonly defaulted to the situation in which only the relative miss position and velocity are known without any corresponding state error covariance information. The various usual methods of finding a maximum P (sub c) do

  3. E-learning objects and actor-networks as configuring information literacy teaching

    DEFF Research Database (Denmark)

    Schreiber, Trine Louise

    2017-01-01

    Introduction. With actor-network theory (ANT) as the theoretical lens the aim of the paper is to examine attempts to build network for shaping information literacy teaching. Method. The paper is based on a study of a project in 2014-2016 where information professionals representing ten educational...... libraries produced and implemented e-learning objects in information literacy teaching. The material was collected through interviews, observations, documents and feedback sessions. Analysis. Latour´s concept of translation and Callon´s four translation moments are used to analyze the network building...... that a network configuring information literacy teaching based on new interactive roles has not been stabilized. Conclusion. The paper concludes that the strength of ANT is first of all the mediation of an overview of different kinds of actors involved in network building. Further, the paper proposes to combine...

  4. An improved bathymetry compilation for the Bellingshausen Sea, Antarctica, to inform ice-sheet and ocean models

    Directory of Open Access Journals (Sweden)

    A. G. C. Graham

    2011-02-01

    Full Text Available The southern Bellingshausen Sea (SBS is a rapidly-changing part of West Antarctica, where oceanic and atmospheric warming has led to the recent basal melting and break-up of the Wilkins ice shelf, the dynamic thinning of fringing glaciers, and sea-ice reduction. Accurate sea-floor morphology is vital for understanding the continued effects of each process upon changes within Antarctica's ice sheets. Here we present a new bathymetric grid for the SBS compiled from shipborne multibeam echo-sounder, spot-sounding and sub-ice measurements. The 1-km grid is the most detailed compilation for the SBS to-date, revealing large cross-shelf troughs, shallow banks, and deep inner-shelf basins that continue inland of coastal ice shelves. The troughs now serve as pathways which allow warm deep water to access the ice sheet in the SBS. Our dataset highlights areas still lacking bathymetric constraint, as well as regions for further investigation, including the likely routes of palaeo-ice streams. The new compilation is a major improvement upon previous grids and will be a key dataset for incorporating into simulations of ocean circulation, ice-sheet change and history. It will also serve forecasts of ice stability and future sea-level contributions from ice loss in West Antarctica, required for the next IPCC assessment report in 2013.

  5. The Problem of Informational Object Identification in Case of the Considerable Quantity of Identifying Features

    Directory of Open Access Journals (Sweden)

    S. D. Kulik

    2010-03-01

    Full Text Available The modification of the algorithm of identification of the informational object, used for identification of the hand-written texts performer in an automated workplace of the forensic expert, is presented. As modification, it is offered to use a method of association rules discovery for definition of statistically dependent sets of feature of hand-written capital letters of the Russian language. The algorithm is approved on set of 691 samples of hand-written documents for which about 2000 identifying feature are defined. The modification of the identification algorithm allows to lower level of errors and to raise quality of accepted decisions for information security.

  6. Creation of integrated information model of 'Ukryttya' object premises and industrial site conditions to support works

    International Nuclear Information System (INIS)

    Postil, S.D.; Ermolenko, A.I.; Ivanov, V.V.; Kotlyarov, V.T.

    2004-01-01

    Data integration is made using standard AutoCAD utility and special software developed in Visual Basic for Application language. Mutual transfer is realized between the applications prepared in Access and AutoCAD with displaying the submitted information. The work demonstrates a possibility to apply integrated information model for investigating radiation field's change and analysis regularities in premises and on industrial site area, development and visualization, with the use of computer animation means, of movement routes, displaying of emergency situations being forecast with the help of computer graphics means, integration of raster display of structures and vector computer model of objects

  7. Timing, timing, timing: Fast decoding of object information from intracranial field potentials in human visual cortex

    Science.gov (United States)

    Liu, Hesheng; Agam, Yigal; Madsen, Joseph R.; Kreiman, Gabriel

    2010-01-01

    Summary The difficulty of visual recognition stems from the need to achieve high selectivity while maintaining robustness to object transformations within hundreds of milliseconds. Theories of visual recognition differ in whether the neuronal circuits invoke recurrent feedback connections or not. The timing of neurophysiological responses in visual cortex plays a key role in distinguishing between bottom-up and top-down theories. Here we quantified at millisecond resolution the amount of visual information conveyed by intracranial field potentials from 912 electrodes in 11 human subjects. We could decode object category information from human visual cortex in single trials as early as 100 ms post-stimulus. Decoding performance was robust to depth rotation and scale changes. The results suggest that physiological activity in the temporal lobe can account for key properties of visual recognition. The fast decoding in single trials is compatible with feed-forward theories and provides strong constraints for computational models of human vision. PMID:19409272

  8. A Strategy for Grasping unknown Objects based on Co-Planarity and Colour Information

    DEFF Research Database (Denmark)

    Popovic, Mila; Kraft, Dirk; Bodenhagen, Leon

    2010-01-01

    with a reasonable success rate in rather complex environments (i.e., cluttered scenes with multiple objects). Moreover, we have embedded the algorithm within a cognitive system that allows for autonomous exploration and learning in different contexts. First, the system is able to perform long action sequences which......, although the grasping attempts not being always successful, can recover from mistakes and more importantly, is able to evaluate the success of the grasps autonomously by haptic feedback (i.e., by a force torque sensor at the wrist and proprioceptive information about the distance of the gripper after...... a gasping attempt). Such labelled data is then used for improving the initially hard-wired algorithm by learning. Moreover, the grasping behaviour has been used in a cognitive system to trigger higher level processes such as object learning and learning of object specific grasping....

  9. 2012 Swimming Season Fact Sheets

    Science.gov (United States)

    To help beachgoers make informed decisions about swimming at U.S. beaches, EPA annually publishes state-by-state data about beach closings and advisories for the previous year's swimming season. These fact sheets summarize that information by state.

  10. Selection of security system design via games of imperfect information and multi-objective genetic algorithm

    International Nuclear Information System (INIS)

    Lins, Isis Didier; Rêgo, Leandro Chaves; Moura, Márcio das Chagas

    2013-01-01

    This work analyzes the strategic interaction between a defender and an intelligent attacker by means of a game and reliability framework involving a multi-objective approach and imperfect information so as to support decision-makers in choosing efficiently designed security systems. A multi-objective genetic algorithm is used to determine the optimal security system's configurations representing the tradeoff between the probability of a successful defense and the acquisition and operational costs. Games with imperfect information are considered, in which the attacker has limited knowledge about the actual security system. The types of security alternatives are readily observable, but the number of redundancies actually implemented in each security subsystem is not known. The proposed methodology is applied to an illustrative example considering power transmission lines in the Northeast of Brazil, which are often targets for attackers who aims at selling the aluminum conductors. The empirical results show that the framework succeeds in handling this sort of strategic interaction. -- Highlights: ► Security components must have feasible costs and must be reliable. ► The optimal design of security systems considers a multi-objective approach. ► Games of imperfect information enable the choice of non-dominated configurations. ► MOGA, reliability and games support the entire defender's decision process. ► The selection of effective security systems may discourage attacker's actions

  11. Vibrotactile feedback for conveying object shape information as perceived by artificial sensing of robotic arm.

    Science.gov (United States)

    Khasnobish, Anwesha; Pal, Monalisa; Sardar, Dwaipayan; Tibarewala, D N; Konar, Amit

    2016-08-01

    This work is a preliminary study towards developing an alternative communication channel for conveying shape information to aid in recognition of items when tactile perception is hindered. Tactile data, acquired during object exploration by sensor fitted robot arm, are processed to recognize four basic geometric shapes. Patterns representing each shape, classified from tactile data, are generated using micro-controller-driven vibration motors which vibrotactually stimulate users to convey the particular shape information. These motors are attached on the subject's arm and their psychological (verbal) responses are recorded to assess the competence of the system to convey shape information to the user in form of vibrotactile stimulations. Object shapes are classified from tactile data with an average accuracy of 95.21 %. Three successive sessions of shape recognition from vibrotactile pattern depicted learning of the stimulus from subjects' psychological response which increased from 75 to 95 %. This observation substantiates the learning of vibrotactile stimulation in user over the sessions which in turn increase the system efficacy. The tactile sensing module and vibrotactile pattern generating module are integrated to complete the system whose operation is analysed in real-time. Thus, the work demonstrates a successful implementation of the complete schema of artificial tactile sensing system for object-shape recognition through vibrotactile stimulations.

  12. The digital object identifier (DOI in electronic scientific journals of communication and information

    Directory of Open Access Journals (Sweden)

    Erik André de Nazaré Pires

    2017-06-01

    Full Text Available The present study seeks to investigate the use of the Digital Object Identifier (DOI in the scientific journals of Communication and Information and, providing new integration utilities with the Lattes Platform. In this sense, it aims to inform the existing titles in Communication Information in electronic format, demonstrate the importance of DOI in the integration with the Lattes Platform in order to guarantee author credibility and analyze the characteristics of publications that have DOI. The methodology used for the development of this study is bibliographic, research with descriptive-descriptive characteristics. From the development of the research, it is inferred that of all the analyzed journals (33 journals, 10 titles in the evaluation of 2013 and 06 titles of the evaluation of 2014 present DOI in their publications, all have WebQualis classification, Qualis A1 in the area Communication and Information. Most publications are international and only 3 titles are national. It is necessary that journals, principally national ones, accompany new technologies such as DOI for objects and ORCID for the identification of people, bringing more mechanisms that guarantee authors 'credibility and to bring the researchers' connection, and both can already be adopted in the Platform Lattes.

  13. Environment as a witness: Selective proliferation of information and emergence of objectivity in a quantum universe

    International Nuclear Information System (INIS)

    Ollivier, Harold; Poulin, David; Zurek, Wojciech H.

    2005-01-01

    We study the role of the information deposited in the environment of an open quantum system in the course of the decoherence process. Redundant spreading of information--the fact that some observables of the system can be independently read off from many distinct fragments of the environment--is investigated as the key to effective objectivity, the essential ingredient of classical reality. This focus on the environment as a communication channel through which observers learn about physical systems underscores the importance of quantum Darwinism--selective proliferation of information about 'the fittest states' chosen by the dynamics of decoherence at the expense of their superpositions--as redundancy imposes the existence of preferred observables. We demonstrate that the only observables that can leave multiple imprints in the environment are the familiar pointer observables singled out by environment-induced superselection (einselection) for their predictability. Many independent observers monitoring the environment will therefore agree on properties of the system as they can only learn about preferred observables. In this operational sense, the selective spreading of information leads to appearance of an objective classical reality from within the quantum substrate

  14. Redundant imprinting of information in nonideal environments: Objective reality via a noisy channel

    International Nuclear Information System (INIS)

    Zwolak, Michael; Quan, H. T.; Zurek, Wojciech H.

    2010-01-01

    Quantum Darwinism provides an information-theoretic framework for the emergence of the objective, classical world from the quantum substrate. The key to this emergence is the proliferation of redundant information throughout the environment where observers can then intercept it. We study this process for a purely decohering interaction when the environment, E, is in a nonideal (e.g., mixed) initial state. In the case of good decoherence, that is, after the pointer states have been unambiguously selected, the mutual information between the system, S, and an environment fragment, F, is given solely by F's entropy increase. This demonstrates that the environment's capacity for recording the state of S is directly related to its ability to increase its entropy. Environments that remain nearly invariant under the interaction with S, either because they have a large initial entropy or a misaligned initial state, therefore have a diminished ability to acquire information. To elucidate the concept of good decoherence, we show that, when decoherence is not complete, the deviation of the mutual information from F's entropy change is quantified by the quantum discord, i.e., the excess mutual information between S and F is information regarding the initial coherence between pointer states of S. In addition to illustrating these results with a single-qubit system interacting with a multiqubit environment, we find scaling relations for the redundancy of information acquired by the environment that display a universal behavior independent of the initial state of S. Our results demonstrate that Quantum Darwinism is robust with respect to nonideal initial states of the environment: the environment almost always acquires redundant information about the system but its rate of acquisition can be reduced.

  15. NEODyS: an online information system for near-Earth objects

    Science.gov (United States)

    Chesley, S. R.; Milani, A.

    1999-09-01

    The Near-Earth Object Dynamics Site (NEODyS) is an online information service for near-Earth asteroids (NEAs). Fundamentally, NEODyS is a database of NEA information; however, the distinguishing feature of the system is the degree to which the information is made available on the World Wide Web. In NEODyS every NEA has its own ``home page'' containing sections devoted to the object's orbit, observations, and close encounters. NEODyS provides interactive ephemeris services to the observer in both tabular and graphical forms. The graphical ephemeris provides a depiction of the uncertainty region on the celestial sphere, including nonlinear effects, which can be of paramount importance in the recovery of lost or nearly lost objects. With the database query service one may search for all asteroids possessing some desired orbital characteristics. This makes it easy, for example, to find all of the asteroids which are large enough to be hazardous, and can come close to the Earth, yet are effectively lost. New features expected to be in place soon include an observation planning service, which will allow the user to easily determine which NEAs are presently observable. This will be implemented with a database query of the current ephemerides, with uncertainty, for all NEODyS objects. The other planned expansion is a close approach monitoring system, which will report all potential close approaches within a fixed distance to all planets and to the largest asteroids which are compatible with the observations. The database is automatically updated on a daily basis as new observations are released from the Minor Planet Center. All of the data files needed to reproduce the NEODyS results are freely available, even the OrbFit software used for orbit determination. NEODyS can be accessed at URL http://newton.dm.unipi.it/neodys. NEODyS has been funded by NATO, the Italian Space Agency (ASI), Consiglio Nazionale delle Ricerche (CNR), and the University of Pisa.

  16. MATHEMATICAL SUPPORT OF THE INTELLIGENT INFORMATION SYSTEM OF ASSESSING THE OBJECT STATE

    Directory of Open Access Journals (Sweden)

    Sofiia Yakubovska

    2017-11-01

    Full Text Available At present, information technologies (IT are intensively used all over the world in various sectors, and today medical institutions cannot do without them when organizing the process of medical diagnostic. The IT efficiency is determined by the degree of their intellectualization that is by including knowledge bases as their component and by the transition from data processing to the processing of knowledge. The efficiency of making decisions in various areas of activity is determined by the quality and quick delivery of information. Medicine constitutes no exception in this sense. The advanced level of computer technology, applied tools, diagnostics on the basis of automated systems of decision support made it possible to solve the tasks of assessing the state of the object at a qualitatively new level. The subject matter of this study is to ensure the mathematical support of the intelligent information system (IS of assessing the state of the object. The object is understood as a patient who came through a myocardial infarction (MI. The goal of the study is to develop mathematical support of the intelligent IS of assessing and predicting a patient’s condition. To achieve the stated goal, the following tasks were solved: statistically valid and uncorrelated signs were specified; these signs enable distinguishing the group of patients who survived from those who died, “decisive rules” were formulated for predicting the MI clinical outcome. In the process of the study, the mathematical IT of assessing the state of the object was developed. The following result was obtained: the suggested mathematical models for predicting the outcome of myocardial infarction that were developed with the use of the method of discriminant function and took into account human blood values can prevent sudden coronary death and improve the diagnostic efficiency. Conclusions. Mathematical models were developed to predict the state of the object in the event of

  17. Information Filtering via Clustering Coefficients of User-Object Bipartite Networks

    Science.gov (United States)

    Guo, Qiang; Leng, Rui; Shi, Kerui; Liu, Jian-Guo

    The clustering coefficient of user-object bipartite networks is presented to evaluate the overlap percentage of neighbors rating lists, which could be used to measure interest correlations among neighbor sets. The collaborative filtering (CF) information filtering algorithm evaluates a given user's interests in terms of his/her friends' opinions, which has become one of the most successful technologies for recommender systems. In this paper, different from the object clustering coefficient, users' clustering coefficients of user-object bipartite networks are introduced to improve the user similarity measurement. Numerical results for MovieLens and Netflix data sets show that users' clustering effects could enhance the algorithm performance. For MovieLens data set, the algorithmic accuracy, measured by the average ranking score, can be improved by 12.0% and the diversity could be improved by 18.2% and reach 0.649 when the recommendation list equals to 50. For Netflix data set, the accuracy could be improved by 14.5% at the optimal case and the popularity could be reduced by 13.4% comparing with the standard CF algorithm. Finally, we investigate the sparsity effect on the performance. This work indicates the user clustering coefficients is an effective factor to measure the user similarity, meanwhile statistical properties of user-object bipartite networks should be investigated to estimate users' tastes.

  18. Cholera Fact Sheet

    Science.gov (United States)

    ... news-room/fact-sheets/detail/cholera","@context":"http://schema.org","@type":"Article"}; العربية 中文 français русский español ... that includes feedback at the local level and information-sharing at the global level. Cholera cases are ...

  19. RESEARCH ON REMOTE SENSING GEOLOGICAL INFORMATION EXTRACTION BASED ON OBJECT ORIENTED CLASSIFICATION

    Directory of Open Access Journals (Sweden)

    H. Gao

    2018-04-01

    Full Text Available The northern Tibet belongs to the Sub cold arid climate zone in the plateau. It is rarely visited by people. The geological working conditions are very poor. However, the stratum exposures are good and human interference is very small. Therefore, the research on the automatic classification and extraction of remote sensing geological information has typical significance and good application prospect. Based on the object-oriented classification in Northern Tibet, using the Worldview2 high-resolution remote sensing data, combined with the tectonic information and image enhancement, the lithological spectral features, shape features, spatial locations and topological relations of various geological information are excavated. By setting the threshold, based on the hierarchical classification, eight kinds of geological information were classified and extracted. Compared with the existing geological maps, the accuracy analysis shows that the overall accuracy reached 87.8561 %, indicating that the classification-oriented method is effective and feasible for this study area and provides a new idea for the automatic extraction of remote sensing geological information.

  20. Multidimensional building objects in a Danish geo-information infrastructure perspective

    DEFF Research Database (Denmark)

    Schrøder, Lise

    2002-01-01

    The emerging multidimensional GI- and VR-technologies within the professional disciplines dealing with design, planning and management processes is leading to a demand for four-dimensional building objects as part of the public geo-information infrastructure. The other way around the recognition...... of the building as a four-dimensional geo-phenomenon will provide a reference between different data sets whether representing buildings in two, three or four dimensions. Finally a central issue is the potential in using frameworks of multidimensional representations as interfaces to the available data sets...

  1. Brain activity related to working memory for temporal order and object information.

    Science.gov (United States)

    Roberts, Brooke M; Libby, Laura A; Inhoff, Marika C; Ranganath, Charan

    2017-06-08

    Maintaining items in an appropriate sequence is important for many daily activities; however, remarkably little is known about the neural basis of human temporal working memory. Prior work suggests that the prefrontal cortex (PFC) and medial temporal lobe (MTL), including the hippocampus, play a role in representing information about temporal order. The involvement of these areas in successful temporal working memory, however, is less clear. Additionally, it is unknown whether regions in the PFC and MTL support temporal working memory across different timescales, or at coarse or fine levels of temporal detail. To address these questions, participants were scanned while completing 3 working memory task conditions (Group, Position and Item) that were matched in terms of difficulty and the number of items to be actively maintained. Group and Position trials probed temporal working memory processes, requiring the maintenance of hierarchically organized coarse and fine temporal information, respectively. To isolate activation related to temporal working memory, Group and Position trials were contrasted against Item trials, which required detailed working memory maintenance of visual objects. Results revealed that working memory encoding and maintenance of temporal information relative to visual information was associated with increased activation in dorsolateral PFC (DLPFC), and perirhinal cortex (PRC). In contrast, maintenance of visual details relative to temporal information was characterized by greater activation of parahippocampal cortex (PHC), medial and anterior PFC, and retrosplenial cortex. In the hippocampus, a dissociation along the longitudinal axis was observed such that the anterior hippocampus was more active for working memory encoding and maintenance of visual detail information relative to temporal information, whereas the posterior hippocampus displayed the opposite effect. Posterior parietal cortex was the only region to show sensitivity to temporal

  2. Multi-Objective Optimization of Experiments Using Curvature and Fisher Information Matrix

    Directory of Open Access Journals (Sweden)

    Erica Manesso

    2017-11-01

    Full Text Available The bottleneck in creating dynamic models of biological networks and processes often lies in estimating unknown kinetic model parameters from experimental data. In this regard, experimental conditions have a strong influence on parameter identifiability and should therefore be optimized to give the maximum information for parameter estimation. Existing model-based design of experiment (MBDOE methods commonly rely on the Fisher information matrix (FIM for defining a metric of data informativeness. When the model behavior is highly nonlinear, FIM-based criteria may lead to suboptimal designs, as the FIM only accounts for the linear variation in the model outputs with respect to the parameters. In this work, we developed a multi-objective optimization (MOO MBDOE, for which the model nonlinearity was taken into consideration through the use of curvature. The proposed MOO MBDOE involved maximizing data informativeness using a FIM-based metric and at the same time minimizing the model curvature. We demonstrated the advantages of the MOO MBDOE over existing FIM-based and other curvature-based MBDOEs in an application to the kinetic modeling of fed-batch fermentation of baker’s yeast.

  3. Adding Hierarchical Objects to Relational Database General-Purpose XML-Based Information Managements

    Science.gov (United States)

    Lin, Shu-Chun; Knight, Chris; La, Tracy; Maluf, David; Bell, David; Tran, Khai Peter; Gawdiak, Yuri

    2006-01-01

    NETMARK is a flexible, high-throughput software system for managing, storing, and rapid searching of unstructured and semi-structured documents. NETMARK transforms such documents from their original highly complex, constantly changing, heterogeneous data formats into well-structured, common data formats in using Hypertext Markup Language (HTML) and/or Extensible Markup Language (XML). The software implements an object-relational database system that combines the best practices of the relational model utilizing Structured Query Language (SQL) with those of the object-oriented, semantic database model for creating complex data. In particular, NETMARK takes advantage of the Oracle 8i object-relational database model using physical-address data types for very efficient keyword searches of records across both context and content. NETMARK also supports multiple international standards such as WEBDAV for drag-and-drop file management and SOAP for integrated information management using Web services. The document-organization and -searching capabilities afforded by NETMARK are likely to make this software attractive for use in disciplines as diverse as science, auditing, and law enforcement.

  4. Clean Cities Fact Sheet

    Energy Technology Data Exchange (ETDEWEB)

    2004-01-01

    This fact sheet explains the Clean Cities Program and provides contact information for all coalitions and regional offices. It answers key questions such as: What is the Clean Cities Program? What are alternative fuels? How does the Clean Cities Program work? What sort of assistance does Clean Cities offer? What has Clean Cities accomplished? What is Clean Cities International? and Where can I find more information?

  5. Optimisation of chromatographic resolution using objective functions including both time and spectral information.

    Science.gov (United States)

    Torres-Lapasió, J R; Pous-Torres, S; Ortiz-Bolsico, C; García-Alvarez-Coque, M C

    2015-01-16

    The optimisation of the resolution in high-performance liquid chromatography is traditionally performed attending only to the time information. However, even in the optimal conditions, some peak pairs may remain unresolved. Such incomplete resolution can be still accomplished by deconvolution, which can be carried out with more guarantees of success by including spectral information. In this work, two-way chromatographic objective functions (COFs) that incorporate both time and spectral information were tested, based on the peak purity (analyte peak fraction free of overlapping) and the multivariate selectivity (figure of merit derived from the net analyte signal) concepts. These COFs are sensitive to situations where the components that coelute in a mixture show some spectral differences. Therefore, they are useful to find out experimental conditions where the spectrochromatograms can be recovered by deconvolution. Two-way multivariate selectivity yielded the best performance and was applied to the separation using diode-array detection of a mixture of 25 phenolic compounds, which remained unresolved in the chromatographic order using linear and multi-linear gradients of acetonitrile-water. Peak deconvolution was carried out using the combination of orthogonal projection approach and alternating least squares. Copyright © 2014 Elsevier B.V. All rights reserved.

  6. How Tactile and Function Information Affect Young Children's Ability to Understand the Nature of Food-Appearing, Deceptive Objects

    Science.gov (United States)

    Krause, Christina Miles

    2008-01-01

    Preschool children's (N = 64) ability to use tactile information and function cues on less-realistic and more-realistic food-appearing, deceptive objects was examined before and after training on the function of deceptive objects. They also responded to appearance and reality questions about deceptive objects. Half of the children (F-S:…

  7. Climate change education in informal settings: Using boundary objects to frame network dissemination

    Science.gov (United States)

    Steiner, Mary Ann

    This study of climate change education dissemination takes place in the context of a larger project where institutions in four cities worked together to develop a linked set of informal learning experiences about climate change. Each city developed an organizational network to explore new ways to connect urban audiences with climate change education. The four city-specific networks shared tools, resources, and knowledge with each other. The networks were related in mission and goals, but were structured and functioned differently depending on the city context. This study illustrates how the tools, resources, and knowledge developed in one network were shared with networks in two additional cities. Boundary crossing theory frames the study to describe the role of objects and processes in sharing between networks. Findings suggest that the goals, capacity and composition of networks resulted in a different emphasis in dissemination efforts, in one case to push the approach out to partners for their own work and in the other to pull partners into a more collaborative stance. Learning experiences developed in each city as a result of the dissemination reflected these differences in the city-specific emphasis with the push city diving into messy examples of the approach to make their own examples, and the pull city offering polished experiences to partners in order to build confidence in the climate change messaging. The networks themselves underwent different kinds of growth and change as a result of dissemination. The emphasis on push and use of messy examples resulted in active use of the principles of the approach and the pull emphasis with polished examples resulted in the cultivation of partnerships with the hub and the potential to engage in the educational approach. These findings have implications for boundary object theory as a useful grounding for dissemination designs in the context of networks of informal learning organizations to support a shift in

  8. Promoting social responsibility amongst health care users: medical tourists’ perspectives on an information sheet regarding ethical concerns in medical tourism

    OpenAIRE

    Adams, Krystyna; Snyder, Jeremy; Crooks, Valorie A; Johnston, Rory

    2013-01-01

    Background Medical tourists, persons that travel across international borders with the intention to access non-emergency medical care, may not be adequately informed of safety and ethical concerns related to the practice of medical tourism. Researchers indicate that the sources of information frequently used by medical tourists during their decision-making process may be biased and/or lack comprehensive information regarding individual safety and treatment outcomes, as well as potential im...

  9. Information about the weight of grasped objects from vision and internal models interacts within the primary motor cortex.

    Science.gov (United States)

    Loh, Morrison N; Kirsch, Louise; Rothwell, John C; Lemon, Roger N; Davare, Marco

    2010-05-19

    When grasping and lifting different objects, visual cues and previously acquired knowledge enable us to prepare the upcoming grasp by scaling the fingertip forces according to the actual weight of the object. However, when no visual information is available, the weight of the object has to be predicted based on information learned from previous grasps. Here, we investigated how changes in corticospinal excitability (CSE) and grip force scaling depend on the presence of visual cues and the weight of previously lifted objects. CSE was assessed by delivering transcranial magnetic stimulation (TMS) at different times before grasp of the object. In conditions in which visual information was not provided, the size of motor evoked potentials (MEP) was larger when the object lifted was preceded by a heavy relative to a light object. Interestingly, the previous lift also affected MEP amplitude when visual cues about object weight were available but only in the period immediately after object presentation (50 ms); this effect had already declined for TMS delivered 150 ms after presentation. In a second experiment, we demonstrated that these CSE changes are used by the motor system to scale grip force. This suggests that the corticospinal system stores a "sensorimotor memory" of the grasp of different objects and relies on this memory when no visual cues are present. Moreover, visual information about weight interacts with this stored representation and allows the corticospinal system to switch rapidly to a different model of predictive grasp control.

  10. Sensitivity-Informed De Novo Programming for Many-Objective Water Portfolio Planning Under Uncertainty

    Science.gov (United States)

    Kasprzyk, J. R.; Reed, P. M.; Kirsch, B. R.; Characklis, G. W.

    2009-12-01

    Risk-based water supply management presents severe cognitive, computational, and social challenges to planning in a changing world. Decision aiding frameworks must confront the cognitive biases implicit to risk, the severe uncertainties associated with long term planning horizons, and the consequent ambiguities that shape how we define and solve water resources planning and management problems. This paper proposes and demonstrates a new interactive framework for sensitivity informed de novo programming. The theoretical focus of our many-objective de novo programming is to promote learning and evolving problem formulations to enhance risk-based decision making. We have demonstrated our proposed de novo programming framework using a case study for a single city’s water supply in the Lower Rio Grande Valley (LRGV) in Texas. Key decisions in this case study include the purchase of permanent rights to reservoir inflows and anticipatory thresholds for acquiring transfers of water through optioning and spot leases. A 10-year Monte Carlo simulation driven by historical data is used to provide performance metrics for the supply portfolios. The three major components of our methodology include Sobol globoal sensitivity analysis, many-objective evolutionary optimization and interactive tradeoff visualization. The interplay between these components allows us to evaluate alternative design metrics, their decision variable controls and the consequent system vulnerabilities. Our LRGV case study measures water supply portfolios’ efficiency, reliability, and utilization of transfers in the water supply market. The sensitivity analysis is used interactively over interannual, annual, and monthly time scales to indicate how the problem controls change as a function of the timescale of interest. These results have been used then to improve our exploration and understanding of LRGV costs, vulnerabilities, and the water portfolios’ critical reliability constraints. These results

  11. The state of the Greenland Ice Sheet

    DEFF Research Database (Denmark)

    Simonsen, Sebastian Bjerregaard

    Firn is defined as snow that has survived a melt season and provides the link between the high-frequency variability of the atmosphere to the ”slower” reacting ice sheet.In this thesis, firn is described by a theoretical and statistical approach to accommodate the variability in observed firn...... compaction on ice sheet scales. The modeling objectives are multiple and aim at estimating the contribution from the firn to the observed volume change of the GrIS and to the diffusion of stable water isotopes. The firn modeling then provides crucial information on total mass balance of the Gr......IS and the paleo-temperature reconstructions retrieved from ice cores.The dynamical firn model developed in this thesis explains13 % of the observed volume change of the GrIS from 2003-2008, without contributing to the global sea-level rise. This emphasizes the need for well constraint firn-compaction models. Here...

  12. Assessment of Online Information Literacy Learning Objects For First Year Community

    Directory of Open Access Journals (Sweden)

    Mara Bordignon

    2016-09-01

    Full Text Available Objective – The main objective was to determine whether information literacy (IL learning objects (LOs impact student IL competency, specifically in a foundational first year English composition course. The primary research question was: What is the effectiveness of IL LOs compared to face-to-face instruction in terms of students’ skill acquisition? Methods – The methods involved testing student IL competency through a multiple-choice test given pre- and post-IL intervention. Effectiveness was measured by assessing whether IL competency improves after exposure to one of two interventions: online IL LOs or face-to-face librarian-led workshop. Over two semesters, equal sections of the course were tested for each of these interventions. For the IL LOs group, students first completed a pre-test, then they worked independently through three online IL LOs. The three IL LOs were videos comprised of animation, screen casting, and video capture on these topics: Finding Articles at Seneca Libraries (hereafter referred to as Finding Articles, Finding Articles on Current Issues, and Popular and Scholarly Sources. The students were then given the same test again. For the face-to-face group, the pre- and post-tests were also required for the same number of sections. This study was conducted under institutional ethics approval. Results – Descriptive analysis revealed student test scores increased for both interventions, IL LOs and face-to-face. Test scores increased, on average, between 14 to 37%. In comparing post-tests, results revealed a statistically significant difference only with the first topic, Finding Articles. In this case, the IL LOs (video group outperformed the face-to-face group by at least 10%. No significance, in terms of performance from pre- and post-test scores, was found for the other two topics. Conclusion – Both IL LO and face-to-face library led workshop interventions had a positive impact on students’ IL skill acquisition

  13. EXTRACTION OF BENTHIC COVER INFORMATION FROM VIDEO TOWS AND PHOTOGRAPHS USING OBJECT-BASED IMAGE ANALYSIS

    Directory of Open Access Journals (Sweden)

    M. T. L. Estomata

    2012-07-01

    Full Text Available Mapping benthic cover in deep waters comprises a very small proportion of studies in the field of research. Majority of benthic cover mapping makes use of satellite images and usually, classification is carried out only for shallow waters. To map the seafloor in optically deep waters, underwater videos and photos are needed. Some researchers have applied this method on underwater photos, but made use of different classification methods such as: Neural Networks, and rapid classification via down sampling. In this study, accurate bathymetric data obtained using a multi-beam echo sounder (MBES was attempted to be used as complementary data with the underwater photographs. Due to the absence of a motion reference unit (MRU, which applies correction to the data gathered by the MBES, accuracy of the said depth data was compromised. Nevertheless, even with the absence of accurate bathymetric data, object-based image analysis (OBIA, which used rule sets based on information such as shape, size, area, relative distance, and spectral information, was still applied. Compared to pixel-based classifications, OBIA was able to classify more specific benthic cover types other than coral and sand, such as rubble and fish. Through the use of rule sets on area, less than or equal to 700 pixels for fish and between 700 to 10,000 pixels for rubble, as well as standard deviation values to distinguish texture, fish and rubble were identified. OBIA produced benthic cover maps that had higher overall accuracy, 93.78±0.85%, as compared to pixel-based methods that had an average accuracy of only 87.30±6.11% (p-value = 0.0001, α = 0.05.

  14. Information about the weight of grasped objects from vision and from internal models interacts within the primary motor cortex

    Science.gov (United States)

    Loh, Morrison N; Kirsch, Louise; Rothwell, John C; Lemon, Roger N; Davare, Marco

    2010-01-01

    When grasping and lifting different objects, visual cues and previously acquired knowledge enable us to prepare the upcoming grasp by scaling the fingertip forces according to the actual weight of the object. However, when no visual information is available, the object’s weight has to be predicted based on information learned from previous grasps. Here, we investigated changes in corticospinal excitability (CSE) and grip force scaling depending on the presence of visual cues and the weight of previously lifted objects. CSE was assessed by delivering transcranial magnetic stimulation (TMS) at different times before grasp of the object. In conditions where visual information was not provided, the size of motor evoked potentials (MEP) was larger when the object lifted was preceded by a heavy relative to a light object. Interestingly, the previous lift also affected MEP amplitude when visual cues about object weight were available, but only in the period immediately after (50 ms) object presentation; this effect had already declined for TMS delivered 150 ms after presentation. In a second experiment, we demonstrated that these CSE changes are used by the motor system to scale grip force. This suggests that the corticospinal system stores a ‘sensorimotor memory’ of the grasp of different objects and relies on this memory when no visual cues are present. Moreover, visual information about weight interacts with this stored representation and allows the corticospinal system to switch rapidly to a different model of predictive grasp control. PMID:20484640

  15. Superfund fact sheet: The remedial program. Fact sheet

    International Nuclear Information System (INIS)

    1992-09-01

    The fact sheet describes what various actions the EPA can take to clean up hazardous wastes sites. Explanations of how the criteria for environmental and public health risk assessment are determined and the role of state and local governments in site remediation are given. The fact sheet is one in a series providing reference information about Superfund issues and is intended for readers with no formal scientific training

  16. OBJECTIVES AND FUNCTIONS OF FINANCIAL STATEMENTS UNDER ACCOUNTING INFORMATION SYSTEM AT TRADE ENTITIES

    Directory of Open Access Journals (Sweden)

    CARAIMAN ADRIAN-COSMIN

    2015-12-01

    Full Text Available As Radu said (2009, pag. 91 [6] logical approach developed by accounting, presentation of an exact image of the heritage, the financial situation and financial results, based on a rational thought, a gradual knowledge domain investigated, concepts, tools and processes that allow a better understanding of the essence of economic phenomena and processes. Theoretical framework brings together a number of concepts that are considered fundamental to regulatory or accounting systems applied at the level of the entity to have clearly specified the coordinates of the base and are able to achieve cohesion between the objective of financial statements as true and fair view, financial information and policy characteristics and estimation techniques as a form of expression towards the recognition and presentation of economic reality. The author considers, in the context of the defined system applied within the accounting entities in general, that principles, presents not only a crucial premise, as well as needed necessity in order to show an exact image of the performance and financial position of the entity.

  17. Origin of life. Primordial genetics: Information transfer in a pre-RNA world based on self-replicating beta-sheet amyloid conformers.

    Science.gov (United States)

    Maury, Carl Peter J

    2015-10-07

    The question of the origin of life on Earth can largely be reduced to the question of what was the first molecular replicator system that was able to replicate and evolve under the presumably very harsh conditions on the early Earth. It is unlikely that a functional RNA could have existed under such conditions and it is generally assumed that some other kind of information system preceded the RNA world. Here, I present an informational molecular system that is stable, self-replicative, environmentally responsive, and evolvable under conditions characterized by high temperatures, ultraviolet and cosmic radiation. This postulated pregenetic system is based on the amyloid fold, a functionally unique polypeptide fold characterized by a cross beta-sheet structure in which the beta strands are arranged perpendicular to the fiber axis. Beside an extraordinary structural robustness, the amyloid fold possesses a unique ability to transmit information by a three-dimensional templating mechanism. In amyloidogenesis short peptide monomers are added one by one to the growing end of the fiber. From the same monomeric subunits several structural variants of amyloid may be formed. Then, in a self-replicative mode, a specific amyloid conformer can act as a template and confer its spatially encoded information to daughter molecular entities in a repetitive way. In this process, the specific conformational information, the spatially changed organization, is transmitted; the coding element is the steric zipper structure, and recognition occurs by amino acid side chain complementarity. The amyloid information system fulfills several basic requirements of a primordial evolvable replicator system: (i) it is stable under the presumed primitive Earth conditions, (ii) the monomeric building blocks of the informational polymer can be formed from available prebiotic compounds, (iii) the system is self-assembling and self-replicative and (iv) it is adaptive to changes in the environment and

  18. Fusion of cooperative localization data with dynamic object information using data communication for preventative vehicle safety applications

    Science.gov (United States)

    Kloeden, H.; Schwarz, D.; Rasshofer, R. H.; Biebl, E. M.

    2013-07-01

    Cooperative sensors allow for reliable detection, classification and localization of objects in the vehicle's surroundings - even without a line-of-sight contact to the object. The sensor principle is based on a communication signal between the vehicle and a transponder attached to the object of interest - a pedestrian, for example. Thereby, localization information is gathered by measuring the round-trip time-of-flight (RTOF) and evaluating the angle-of-arrival (AOA) of the incident signal. After that, tracking algorithms are used to recover the kinematic state of the object providing a basis for situation assessment. This paper investigates possibilities and benefits of extending this principle by the communication of information from inertial sensors which are locally attached to the transponder. Furthermore, this paper presents a robust approach for fusing the localization data with dynamic object information using the Dempster-Shafer theory. The approach is evaluated by performing real-world experiments for the analysis of pedestrian accidents.

  19. Informed multi-objective decision-making in environmental management using Pareto optimality

    Science.gov (United States)

    Maureen C. Kennedy; E. David Ford; Peter Singleton; Mark Finney; James K. Agee

    2008-01-01

    Effective decisionmaking in environmental management requires the consideration of multiple objectives that may conflict. Common optimization methods use weights on the multiple objectives to aggregate them into a single value, neglecting valuable insight into the relationships among the objectives in the management problem.

  20. Chlamydia - CDC Fact Sheet

    Science.gov (United States)

    ... Archive STDs Home Page Bacterial Vaginosis (BV) Chlamydia Gonorrhea Genital Herpes Hepatitis HIV/AIDS & STDs Human Papillomavirus ( ... sheet Pelvic Inflammatory Disease (PID) – CDC fact sheet Gonorrhea – CDC fact sheet STDs Home Page Bacterial Vaginosis ( ...

  1. Visual working memory for global, object, and part-based information.

    Science.gov (United States)

    Patterson, Michael D; Bly, Benjamin Martin; Porcelli, Anthony J; Rypma, Bart

    2007-06-01

    We investigated visual working memory for novel objects and parts of novel objects. After a delay period, participants showed strikingly more accurate performance recognizing a single whole object than the parts of that object. This bias to remember whole objects, rather than parts, persisted even when the division between parts was clearly defined and the parts were disconnected from each other so that, in order to remember the single whole object, the participants needed to mentally combine the parts. In addition, the bias was confirmed when the parts were divided by color. These experiments indicated that holistic perceptual-grouping biases are automatically used to organize storage in visual working memory. In addition, our results suggested that the bias was impervious to top-down consciously directed control, because when task demands were manipulated through instruction and catch trials, the participants still recognized whole objects more quickly and more accurately than their parts. This bias persisted even when the whole objects were novel and the parts were familiar. We propose that visual working memory representations depend primarily on the global configural properties of whole objects, rather than part-based representations, even when the parts themselves can be clearly perceived as individual objects. This global configural bias beneficially reduces memory load on a capacity-limited system operating in a complex visual environment, because fewer distinct items must be remembered.

  2. The Shaping of Managers' Security Objectives through Information Security Awareness Training

    Science.gov (United States)

    Harris, Mark A.

    2010-01-01

    Information security research states that corporate security policy and information security training should be socio-technical in nature and that corporations should consider training as a primary method of protecting their information systems. However, information security policies and training are predominately technical in nature. In addition,…

  3. Designing Observation and Modeling Systems to Inform Decisions and Policies on Freshwater Objectives in New Zealand

    Science.gov (United States)

    Baisden, W. T.; Ellis, T.; Rissman, C.; Moore, C.; Matthews, A.

    2016-12-01

    Declines in New Zealand's freshwater quality have led to legislation - the 2014 National Policy Statement on Freshwater Management (NPS-FM) - which requires regional governments to set "objectives" and design policies accordingly. In most regions, increases in freshwater contaminants are derived largely from intensifying agriculture and come as nitrogen, phosphorous or sediment, or a combination thereof. Here, the development and application of N and O isotopes as natural tracers for nitrate is examined as a case study, in the context of a wider hierarchy of observations such as N concentrations, flow and broader hydrochemistry used for NPS-FM implementation. The analysis of N and O isotopes in nitrate provides specific information on sources and removal processes that cannot be obtained by other measurements. Yet, despite considerable development of the technical methodology and environment-specific interpretation, application of measurements has faced barriers. Many may be typical of science in a small advanced nation with a population of 4.5 million, but others are unique due to New Zealand's limited rural population base and large diversity in physical geography, as well as a unique economic reliance on highly productive pastoral agricultural systems. Seventeen different regional governments are empowered to regulate in ways consistent with local consultation and democracy within their catchment boundaries, but with limited resources to align highly technical observational data to policies and decisions, as well as supporting models. The resulting gaps in communication and technical capability combine with a diversity of approaches to pose both challenges and opportunities for development and application of hierarchical observation systems. Success appears to lie in ensuring decision frameworks can be `mapped', so that different frameworks can be compared, and the benefits of sophisticated observations understood directly in relation to influence on regional

  4. Object-oriented analysis and design of a health care management information system.

    Science.gov (United States)

    Krol, M; Reich, D L

    1999-04-01

    We have created a prototype for a universal object-oriented model of a health care system compatible with the object-oriented approach used in version 3.0 of the HL7 standard for communication messages. A set of three models has been developed: (1) the Object Model describes the hierarchical structure of objects in a system--their identity, relationships, attributes, and operations; (2) the Dynamic Model represents the sequence of operations in time as a collection of state diagrams for object classes in the system; and (3) functional Diagram represents the transformation of data within a system by means of data flow diagrams. Within these models, we have defined major object classes of health care participants and their subclasses, associations, attributes and operators, states, and behavioral scenarios. We have also defined the major processes and subprocesses. The top-down design approach allows use, reuse, and cloning of standard components.

  5. Geometry of thin liquid sheet flows

    Science.gov (United States)

    Chubb, Donald L.; Calfo, Frederick D.; Mcconley, Marc W.; Mcmaster, Matthew S.; Afjeh, Abdollah A.

    1994-01-01

    Incompresible, thin sheet flows have been of research interest for many years. Those studies were mainly concerned with the stability of the flow in a surrounding gas. Squire was the first to carry out a linear, invicid stability analysis of sheet flow in air and compare the results with experiment. Dombrowski and Fraser did an experimental study of the disintegration of sheet flows using several viscous liquids. They also detected the formulation of holes in their sheet flows. Hagerty and Shea carried out an inviscid stability analysis and calculated growth rates with experimental values. They compared their calculated growth rates with experimental values. Taylor studied extensively the stability of thin liquid sheets both theoretically and experimentally. He showed that thin sheets in a vacuum are stable. Brown experimentally investigated thin liquid sheet flows as a method of application of thin films. Clark and Dumbrowski carried out second-order stability analysis for invicid sheet flows. Lin introduced viscosity into the linear stability analysis of thin sheet flows in a vacuum. Mansour and Chigier conducted an experimental study of the breakup of a sheet flow surrounded by high-speed air. Lin et al. did a linear stability analysis that included viscosity and a surrounding gas. Rangel and Sirignano carried out both a linear and nonlinear invisid stability analysis that applies for any density ratio between the sheet liquid and the surrounding gas. Now there is renewed interest in sheet flows because of their possible application as low mass radiating surfaces. The objective of this study is to investigate the fluid dynamics of sheet flows that are of interest for a space radiator system. Analytical expressions that govern the sheet geometry are compared with experimental results. Since a space radiator will operate in a vacuum, the analysis does not include any drag force on the sheet flow.

  6. Tata Kelola Pada Perguruan Tinggi Menggunakan Control Objective for Information & Related Technology (COBIT) 5

    OpenAIRE

    asriyanik, asriyanik; Hendayun, Mokhamad

    2017-01-01

    A College needs a good governance in implementation of information technology, especially which related with information security because information is an important asset. Framework which can be used for the preparation of information security governance is COBIT 5 from ISACA. The first step to start the preparation of the governance using COBIT is mapping between the goal of college with enterprise goals (EG), IT Related Goals and domain process COBIT 5. From 15 colleges that have been acc...

  7. Order of the 30 December 2004 relative to the individual sheet of medical follow-up and to the individual information concerning the dosimetry of workers exposed to ionizing radiations

    International Nuclear Information System (INIS)

    2004-12-01

    This order concerns the content and the modalities of grant of the individual sheet of medical follow-up, the collect and the centralization of dosimetry individual information by the Institute of Radiation Protection and Safety (IRSN), and the access to individual results of external and internal dosimetry. (A.L.B.)

  8. Integration of World Knowledge and Temporary Information about Changes in an Object's Environmental Location during Different Stages of Sentence Comprehension.

    Science.gov (United States)

    Chen, Xuqian; Yang, Wei; Ma, Lijun; Li, Jiaxin

    2018-01-01

    Recent findings have shown that information about changes in an object's environmental location in the context of discourse is stored in working memory during sentence comprehension. However, in these studies, changes in the object's location were always consistent with world knowledge (e.g., in "The writer picked up the pen from the floor and moved it to the desk," the floor and the desk are both common locations for a pen). How do people accomplish comprehension when the object-location information in working memory is inconsistent with world knowledge (e.g., a pen being moved from the floor to the bathtub)? In two visual world experiments, with a "look-and-listen" task, we used eye-tracking data to investigate comprehension of sentences that described location changes under different conditions of appropriateness (i.e., the object and its location were typically vs. unusually coexistent, based on world knowledge) and antecedent context (i.e., contextual information that did vs. did not temporarily normalize unusual coexistence between object and location). Results showed that listeners' retrieval of the critical location was affected by both world knowledge and working memory, and the effect of world knowledge was reduced when the antecedent context normalized unusual coexistence of object and location. More importantly, activation of world knowledge and working memory seemed to change during the comprehension process. These results are important because they demonstrate that interference between world knowledge and information in working memory, appears to be activated dynamically during sentence comprehension.

  9. Improving a real-time object detector with compact temporal information

    DEFF Research Database (Denmark)

    Ahrnbom, Martin; Jensen, Morten Bornø; Åström, Kalle

    2017-01-01

    Neural networks designed for real-time object detection have recently improved significantly, but in practice, look- ing at only a single RGB image at the time may not be ideal. For example, when detecting objects in videos, a foreground detection algorithm can be used to obtain compact temporal......, a problem this approach is well suited for. The ac- curacy was found to improve significantly (up to 66%), with a roughly 40% increase in computational time....

  10. 77 FR 38267 - Information Collection; Request for Comment; Objections to New Land Management Plans, Plan...

    Science.gov (United States)

    2012-06-27

    ... notice should be addressed to: USDA, Forest Service, Attn: Chris French, Acting Assistant Director for... information on people, including the use of automated, electronic, mechanical, or other technological...

  11. Chemical Safety Information, Site Security and Fuels Regulatory Relief Act: Public Distribution of Off-Site Consequence Analysis Information Fact Sheet

    Science.gov (United States)

    Based on assessments of increased risk of terrorist/criminal activity, EPA and DOJ have issued a rule that allows public access to OCA information in ways that are designed to minimize likelihood of chemical accidents and public harm.

  12. An X window based graphics user interface for radiation information processing system developed with object-oriented programming technology

    International Nuclear Information System (INIS)

    Gao Wenhuan; Fu Changqing; Kang Kejun

    1993-01-01

    X Window is a network-oriented and network transparent windowing system, and now dominant in the Unix domain. The object-oriented programming technology can be used to change the extensibility of a software system remarkably. An introduction to graphics user interface is given. And how to develop a graphics user interface for radiation information processing system with object-oriented programming technology, which is based on X Window and independent of application is described briefly

  13. Object representation in the bottlenose dolphin (Tursiops truncatus): integration of visual and echoic information.

    Science.gov (United States)

    Harley, H E; Roitblat, H L; Nachtigall, P E

    1996-04-01

    A dolphin performed a 3-alternative matching-to-sample task in different modality conditions (visual/echoic, both vision and echolocation: visual, vision only; echoic, echolocation only). In Experiment 1, training occurred in the dual-modality (visual/echoic) condition. Choice accuracy in tests of all conditions was above chance without further training. In Experiment 2, unfamiliar objects with complementary similarity relations in vision and echolocation were presented in single-modality conditions until accuracy was about 70%. When tested in the visual/echoic condition, accuracy immediately rose (95%), suggesting integration across modalities. In Experiment 3, conditions varied between presentation of sample and alternatives. The dolphin successfully matched familiar objects in the cross-modal conditions. These data suggest that the dolphin has an object-based representational system.

  14. System renewal of objective contents on basis of new information technologies in continuing education in the field of information security

    Directory of Open Access Journals (Sweden)

    Михаил Иванович Бочаров

    2010-06-01

    Full Text Available In the article the questions of the optimization of the contents of education and the processes of its formation and renewal in dynamically developed subject areas are considered. As an example training process of information security according to suggested by the models of the vital cycle of knowledges system of continuing education is investigated.

  15. An Upper Bound on High Speed Satellite Collision Probability When Only One Object has Position Uncertainty Information

    Science.gov (United States)

    Frisbee, Joseph H., Jr.

    2015-01-01

    Upper bounds on high speed satellite collision probability, PC †, have been investigated. Previous methods assume an individual position error covariance matrix is available for each object. The two matrices being combined into a single, relative position error covariance matrix. Components of the combined error covariance are then varied to obtain a maximum PC. If error covariance information for only one of the two objects was available, either some default shape has been used or nothing could be done. An alternative is presented that uses the known covariance information along with a critical value of the missing covariance to obtain an approximate but potentially useful Pc upper bound.

  16. Information Recovery Algorithm for Ground Objects in Thin Cloud Images by Fusing Guide Filter and Transfer Learning

    Directory of Open Access Journals (Sweden)

    HU Gensheng

    2018-03-01

    Full Text Available Ground object information of remote sensing images covered with thin clouds is obscure. An information recovery algorithm for ground objects in thin cloud images is proposed by fusing guide filter and transfer learning. Firstly, multi-resolution decomposition of thin cloud target images and cloud-free guidance images is performed by using multi-directional nonsubsampled dual-tree complex wavelet transform. Then the decomposed low frequency subbands are processed by using support vector guided filter and transfer learning respectively. The decomposed high frequency subbands are enhanced by using modified Laine enhancement function. The low frequency subbands output by guided filter and those predicted by transfer learning model are fused by the method of selection and weighting based on regional energy. Finally, the enhanced high frequency subbands and the fused low frequency subbands are reconstructed by using inverse multi-directional nonsubsampled dual-tree complex wavelet transform to obtain the ground object information recovery images. Experimental results of Landsat-8 OLI multispectral images show that, support vector guided filter can effectively preserve the detail information of the target images, domain adaptive transfer learning can effectively extend the range of available multi-source and multi-temporal remote sensing images, and good effects for ground object information recover are obtained by fusing guide filter and transfer learning to remove thin cloud on the remote sensing images.

  17. A Learning Research Informed Design and Evaluation of a Web-Enhanced Object Oriented Programming Seminar

    Science.gov (United States)

    Georgantaki, Stavroula C.; Retalis, Symeon D.

    2007-01-01

    "Object-Oriented Programming" subject is included in the ACM Curriculum Guidelines for Undergraduate and Graduate Degree Programs in Computer Science as well as in Curriculum for K-12 Computer Science. In a few research studies learning problems and difficulties have been recorded, and therefore, specific pedagogical guidelines and…

  18. Immersion, Embodiment, and Imagination: Moving Beyond an Aesthetic of Objectivity in Research-Informed Performance in Health

    Directory of Open Access Journals (Sweden)

    Julia Gray

    2015-05-01

    Full Text Available Growing numbers of qualitative health researchers of diverse disciplinary backgrounds are experimenting with various forms of performance (e.g., film, live theater, dance as innovative approaches to engage broader communities in complex and critical ways with research. Despite this emerging alliance between performance and research, much of research-informed performance work is informed by an "aesthetic of objectivity," which assumes a linear trajectory between research findings and performance, and minimizes the relevance of aesthetic interpretation, which we argue is fundamental to achieving critical research-informed performative work. To move beyond this aesthetic of objectivity, we will explore our development of a research-informed film, "Fit for Dialysis." We argue that embracing the role of aesthetics, imagination, and embodiment more fully is essential to achieving the full interactive, educational, and emancipatory potential of the alliance between performance and research. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs1502290

  19. Information-educational Portal MEPHIST: a Security Policy at Access Differentiation to Objects

    Directory of Open Access Journals (Sweden)

    A. I. Guseva

    2010-09-01

    Full Text Available The article is devoted to working out of an information-educational portal for National Research Nuclear University “MEPhI”, executed within the limits of realization “Innovative programs of engineering-physical education for a new stage of development of a nuclear science and the industry”of the priority national project “Education”. The basic attention is given to requirements of information safety.

  20. Practical implementation of Wilhelm Osbahr’s entrepreneur balance sheet theory assumptions – a case study

    Directory of Open Access Journals (Sweden)

    EWA ŚNIEŻEK , MICHAŁ WIATR

    2015-12-01

    Full Text Available The aim of this study is to present the possibilities of the practical application of Osbahr’s balance sheet theory assumptions, as one of many possible attempts to close the information gap in the financial reporting of the twenty-first century. Wilhelm Osbahr, at the beginning of the 20th century, made an attempt to solve the problem of indicating the balance sheet values (the impact of balance sheet evaluation on the balance sheet items, from the point of view of an entrepreneur or business owner, at the same time clearly emphasizing the necessity to deal with the balance sheet structure through the prism of the objectives pursued by the company. Osbahr postulated highlighting any changes occurring in the economic structure of the company and its components, which do not result directly from its operating activities, and so to present them in the position called “adjustments”. This article uses the deductive method supported by literature studies and a case study method. The authors using the case study method confirm the possibility of using the described balance sheet theory in the current financial reporting based on actual data of the company ABC Ltd. They also show that a balance sheet which is presented according to the new reporting formula discloses new quality of information for the financial reporting users.

  1. ANTHROPOLOGICAL MEASURING OF COMMUNICATIVE – INFORMATIVE CONSCIOUSNESS OF SENSE OF OBJECTIVE REALITY

    Directory of Open Access Journals (Sweden)

    Vera I. Aksenova

    2013-09-01

    Full Text Available The purpose of the article is to introduce the anthropological aspects of the communicative and information understanding of the meaning of life; to define the anthropological measurements of communicative and information understanding of the meaning of life connected with the introduction of information and informatization: to consider the models of the development of the information society which are introduced in the developed countries of the world for the solution of the anthropological problems; to analyse the problems of the new meaning of life connected with the development of the information society, and to find the ways of their optimization. Methodology. The new anthropological measurements of socialization of a person are revealed thanks to the analysis of the cognitive structures and epistemes. These measurements consist of mastering of codes and genres of the external discourse. Scientific novelty. The author offers the thesis that the social behaviour of people is significantly defined by the possible sign systems which are created by cultures of the concrete societies that represent a new approach in understanding of the communicative and information determinants of the semantic and vital key points of the person and society. The last ones are determined by the expansion of the communicative and information space which demands the formation of the new anthropological basis of life according to which a person enters socialization and forms a new way of life. Conclusions. Anthropological measurements of communicative and information understanding of the meaning of life are reduced to the fact, that they are affected by the network culture, the new types of communication caused by the information technologies, therefore there is a new type of the person – the virtual or network ones. The formation of the personality is defined by the procedure of interpretation which allows to establish within the discursive space the semantic

  2. Direction information acquired from attended objects not from distractors in MOT

    Czech Academy of Sciences Publication Activity Database

    Lukavský, Jiří

    2012-01-01

    Roč. 41, Supplement (2012), s. 140-140 ISSN 0301-0066. [European Conference on Visual Perception . 02.09.2012-06.09.2012, Alghero] R&D Projects: GA ČR GPP407/10/P607 Institutional support: RVO:68081740 Keywords : Multiple Object Tracking * random dot motion * visual attention Subject RIV: AN - Psychology http://www. perception web.com/ecvp/ecvp12_jkt_crop.pdf

  3. Objective burden, resources, and other stressors among informal cancer caregivers: a hidden quality issue?†

    Science.gov (United States)

    van Ryn, Michelle; Sanders, Sara; Kahn, Katherine; van Houtven, Courtney; Griffin, Joan M.; Martin, Michelle; Atienza, Audie A.; Phelan, Sean; Finstad, Deborah; Rowland, Julia

    2015-01-01

    A great deal of clinical cancer care is delivered in the home by informal caregivers (e.g. family, friends), who are often untrained. Caregivers' context varies widely, with many providing care despite low levels of resources and high levels of additional demands. Background Changes in health care have shifted much cancer care to the home, with limited data to inform this transition. We studied the characteristics, care tasks, and needs of informal caregivers of cancer patients. Methods Caregivers of seven geographically and institutionally defined cohorts of newly diagnosed colorectal and lung cancer patients completed self-administered questionnaires (n = 677). We combined this information with patient survey and chart abstraction data and focused on caregivers who reported providing, unpaid, at least 50% of the patient's informal cancer care. Results Over half of caregivers (55%) cared for a patient with metastatic disease, severe comorbidity, or undergoing current treatment. Besides assisting with activities of daily living, caregivers provided cancer-specific care such as watching for treatment side effects (68%), helping manage pain, nausea or fatigue (47%), administering medicine (34%), deciding whether to call a doctor (30%), deciding whether medicine was needed (29%), and changing bandages (19%). However, half of caregivers reported not getting training perceived as necessary. In addition, 49% of caregivers worked for pay, 21% reported poor or fair health, and 21% provided unpaid care for other individuals. One in four reported low confidence in the quality of the care they provided. Conclusions Much assistance for cancer patients is delivered in the home by informal caregivers, often without desired training, with a significant minority having limited resources and high additional demands. Future research should explore the potentially high yield of addressing caregiver needs in improving quality of cancer care and both survivors' and caregivers' outcomes

  4. Hospital discharge: What are the problems, information needs and objectives of community pharmacists? A mixed method approach

    Directory of Open Access Journals (Sweden)

    Brühwiler LD

    2017-09-01

    Full Text Available Background: After hospital discharge, community pharmacists are often the first health care professionals the discharged patient encounters. They reconcile and dispense prescribed medicines and provide pharmaceutical care. Compared to the roles of general practitioners, the pharmacists’ needs to perform these tasks are not well known. Objective: This study aims to a Identify community pharmacists’ current problems and roles at hospital discharge, b Assess their information needs, specifically the availability and usefulness of information, and c Gain insight into pharmacists’ objectives and ideas for discharge optimisation. Methods: A focus group was conducted with a sample of six community pharmacists from different Swiss regions. Based on these qualitative results, a nationwide online-questionnaire was sent to 1348 Swiss pharmacies. Results: The focus group participants were concerned about their extensive workload with discharge prescriptions and about gaps in therapy. They emphasised the importance of more extensive information transfer. This applied especially to medication changes, unclear prescriptions, and information about a patient's care. Participants identified treatment continuity as a main objective when it comes to discharge optimisation. There were 194 questionnaires returned (response rate 14.4%. The majority of respondents reported to fulfil their role as defined by the Joint-FIP/WHO Guideline on Good Pharmacy Practice (rather badly. They reported many unavailable but useful information items, like therapy changes, allergies, specifications for “off-label” medication use or contact information. Information should be delivered in a structured way, but no clear preference for one particular transfer method was found. Pharmacists requested this information in order to improve treatment continuity and patient safety, and to be able to provide better pharmaceutical care services. Conclusion: Surveyed Swiss community

  5. The Role of Sensory-Motor Information in Object Recognition: Evidence from Category-Specific Visual Agnosia

    Science.gov (United States)

    Wolk, D.A.; Coslett, H.B.; Glosser, G.

    2005-01-01

    The role of sensory-motor representations in object recognition was investigated in experiments involving AD, a patient with mild visual agnosia who was impaired in the recognition of visually presented living as compared to non-living entities. AD named visually presented items for which sensory-motor information was available significantly more…

  6. Directed cortical information flow during human object recognition: analyzing induced EEG gamma-band responses in brain's source space.

    Directory of Open Access Journals (Sweden)

    Gernot G Supp

    Full Text Available The increase of induced gamma-band responses (iGBRs; oscillations >30 Hz elicited by familiar (meaningful objects is well established in electroencephalogram (EEG research. This frequency-specific change at distinct locations is thought to indicate the dynamic formation of local neuronal assemblies during the activation of cortical object representations. As analytically power increase is just a property of a single location, phase-synchrony was introduced to investigate the formation of large-scale networks between spatially distant brain sites. However, classical phase-synchrony reveals symmetric, pair-wise correlations and is not suited to uncover the directionality of interactions. Here, we investigated the neural mechanism of visual object processing by means of directional coupling analysis going beyond recording sites, but rather assessing the directionality of oscillatory interactions between brain areas directly. This study is the first to identify the directionality of oscillatory brain interactions in source space during human object recognition and suggests that familiar, but not unfamiliar, objects engage widespread reciprocal information flow. Directionality of cortical information-flow was calculated based upon an established Granger-Causality coupling-measure (partial-directed coherence; PDC using autoregressive modeling. To enable comparison with previous coupling studies lacking directional information, phase-locking analysis was applied, using wavelet-based signal decompositions. Both, autoregressive modeling and wavelet analysis, revealed an augmentation of iGBRs during the presentation of familiar objects relative to unfamiliar controls, which was localized to inferior-temporal, superior-parietal and frontal brain areas by means of distributed source reconstruction. The multivariate analysis of PDC evaluated each possible direction of brain interaction and revealed widespread reciprocal information-transfer during familiar

  7. The User Interface: A Hypertext Model Linking Art Objects and Related Information.

    Science.gov (United States)

    Moline, Judi

    This report presents a model combining the emerging technologies of hypertext and expert systems. Hypertext is relatively unexplored but promises an innovative approach to information retrieval. In contrast, expert systems have been used experimentally in many different application areas ranging from medical diagnosis to oil exploration. The…

  8. Integration of World Knowledge and Temporary Information about Changes in an Object's Environmental Location during Different Stages of Sentence Comprehension

    Directory of Open Access Journals (Sweden)

    Xuqian Chen

    2018-02-01

    Full Text Available Recent findings have shown that information about changes in an object's environmental location in the context of discourse is stored in working memory during sentence comprehension. However, in these studies, changes in the object's location were always consistent with world knowledge (e.g., in “The writer picked up the pen from the floor and moved it to the desk,” the floor and the desk are both common locations for a pen. How do people accomplish comprehension when the object-location information in working memory is inconsistent with world knowledge (e.g., a pen being moved from the floor to the bathtub? In two visual world experiments, with a “look-and-listen” task, we used eye-tracking data to investigate comprehension of sentences that described location changes under different conditions of appropriateness (i.e., the object and its location were typically vs. unusually coexistent, based on world knowledge and antecedent context (i.e., contextual information that did vs. did not temporarily normalize unusual coexistence between object and location. Results showed that listeners' retrieval of the critical location was affected by both world knowledge and working memory, and the effect of world knowledge was reduced when the antecedent context normalized unusual coexistence of object and location. More importantly, activation of world knowledge and working memory seemed to change during the comprehension process. These results are important because they demonstrate that interference between world knowledge and information in working memory, appears to be activated dynamically during sentence comprehension.

  9. ℓ0 -based sparse hyperspectral unmixing using spectral information and a multi-objectives formulation

    Science.gov (United States)

    Xu, Xia; Shi, Zhenwei; Pan, Bin

    2018-07-01

    Sparse unmixing aims at recovering pure materials from hyperpspectral images and estimating their abundance fractions. Sparse unmixing is actually ℓ0 problem which is NP-h ard, and a relaxation is often used. In this paper, we attempt to deal with ℓ0 problem directly via a multi-objective based method, which is a non-convex manner. The characteristics of hyperspectral images are integrated into the proposed method, which leads to a new spectra and multi-objective based sparse unmixing method (SMoSU). In order to solve the ℓ0 norm optimization problem, the spectral library is encoded in a binary vector, and a bit-wise flipping strategy is used to generate new individuals in the evolution process. However, a multi-objective method usually produces a number of non-dominated solutions, while sparse unmixing requires a single solution. How to make the final decision for sparse unmixing is challenging. To handle this problem, we integrate the spectral characteristic of hyperspectral images into SMoSU. By considering the spectral correlation in hyperspectral data, we improve the Tchebycheff decomposition function in SMoSU via a new regularization item. This regularization item is able to enforce the individual divergence in the evolution process of SMoSU. In this way, the diversity and convergence of population is further balanced, which is beneficial to the concentration of individuals. In the experiments part, three synthetic datasets and one real-world data are used to analyse the effectiveness of SMoSU, and several state-of-art sparse unmixing algorithms are compared.

  10. Impact of information technology on vendor objectives, capabilities, and competences in contract electronic manufacturing

    DEFF Research Database (Denmark)

    Perunovic, Zoran; Mefford, Robert; Christoffersen, Mads

    2012-01-01

    IT impacts vendor capabilities. The research framework integrates four concepts/theories: the resource-based view (RBV), the concept of manufacturing strategy, the concept of business performance, and the concept of IT impact on business performance. Two case companies are studied, one with a high level...... proposed. The method gives valuable insights into how IT enables competences, enhances capabilities, and contributes to the fulfillment of vendor objectives. A model of how IT affects a vendor's competitiveness is proposed. In addition, two initiatives for optimizing the utilization of IT are suggested....

  11. Creation of integrated information model of premises (blocks B, G, RDAS and deaerator) state of 'Ukryttia' object to support works

    International Nuclear Information System (INIS)

    Postil, S.D.; Ermolenko, A.I.; Ivanov, V.V.; Kotlyarov, V.T.

    2003-01-01

    The principles of organization of connection between the attachments prepared in Access and AutoCAD are developed,and a technology of transfer from one application into another with displaying of delivered information is realized.Information models of Reactor Department Auxiliary Systems (RDAS) block premises from axes 25 to 51,and from rows 'U' to 'Yu', deaerator stack from axes 34 to 68,and from row 'B' to 'D', and turbine hall from axes 34 to 68 and from row 'A' to 'B',are created.The possibility is shown of using integrated information model to develop and visualize by means of computer animation the access routes in 'Ukryttia' object premises,to integrate raster image of structure and vector computer model of Object

  12. OOMM--Object-Oriented Matrix Modelling: an instrument for the integration of the Brasilia Regional Health Information System.

    Science.gov (United States)

    Cammarota, M; Huppes, V; Gaia, S; Degoulet, P

    1998-01-01

    The development of Health Information Systems is widely determined by the establishment of the underlying information models. An Object-Oriented Matrix Model (OOMM) is described which target is to facilitate the integration of the overall health system. The model is based on information modules named micro-databases that are structured in a three-dimensional network: planning, health structures and information systems. The modelling tool has been developed as a layer on top of a relational database system. A visual browser facilitates the development and maintenance of the information model. The modelling approach has been applied to the Brasilia University Hospital since 1991. The extension of the modelling approach to the Brasilia regional health system is considered.

  13. Competitor Orientation: Effects of Objectives and Information on Managerial Decisions and Profitability

    OpenAIRE

    Armstrong, J. Scott; Collopy, Fred

    1996-01-01

    Managers are often advised, "beat your competitors," which sometimes contrasts with the advice, "do the best for your firm." This may lead managers to focus on comparative measures such as market share. Drawing on game theory, the authors hypothesize that managers are competitor-oriented under certain conditions, in particular, when they are provided with information about competitors' performance. Empirical studies lead to the additional hypothesis that a competitor orientation is detrimenta...

  14. Contractor Past Performance Information: An Analysis of Assessment Narratives and Objective Ratings

    Science.gov (United States)

    2015-04-30

    narratives, and improving the disclosure of CPARS program office audit results (Black et al., 2014, pp. 48–49). Summary, Conclusions, and Recommendations...office audit results (Black et al., 2014, pp. 44–49). Recommendations Based on our conclusions, we identified the following five recommendations...and information technology (5th ed.). New York, NY: McGraw -Hill. Freeman, R. E. (1984). Strategic management: A stakeholder approach. Boston, MA

  15. Astrophysical Information from Objective Prism Digitized Images: Classification with an Artificial Neural Network

    Directory of Open Access Journals (Sweden)

    Bratsolis Emmanuel

    2005-01-01

    Full Text Available Stellar spectral classification is not only a tool for labeling individual stars but is also useful in studies of stellar population synthesis. Extracting the physical quantities from the digitized spectral plates involves three main stages: detection, extraction, and classification of spectra. Low-dispersion objective prism images have been used and automated methods have been developed. The detection and extraction problems have been presented in previous works. In this paper, we present a classification method based on an artificial neural network (ANN. We make a brief presentation of the entire automated system and we compare the new classification method with the previously used method of maximum correlation coefficient (MCC. Digitized photographic material has been used here. The method can also be used on CCD spectral images.

  16. Object-based image analysis and data mining for building ontology of informal urban settlements

    Science.gov (United States)

    Khelifa, Dejrriri; Mimoun, Malki

    2012-11-01

    During recent decades, unplanned settlements have been appeared around the big cities in most developing countries and as consequence, numerous problems have emerged. Thus the identification of different kinds of settlements is a major concern and challenge for authorities of many countries. Very High Resolution (VHR) Remotely Sensed imagery has proved to be a very promising way to detect different kinds of settlements, especially through the using of new objectbased image analysis (OBIA). The most important key is in understanding what characteristics make unplanned settlements differ from planned ones, where most experts characterize unplanned urban areas by small building sizes at high densities, no orderly road arrangement and Lack of green spaces. Knowledge about different kinds of settlements can be captured as a domain ontology that has the potential to organize knowledge in a formal, understandable and sharable way. In this work we focus on extracting knowledge from VHR images and expert's knowledge. We used an object based strategy by segmenting a VHR image taken over urban area into regions of homogenous pixels at adequate scale level and then computing spectral, spatial and textural attributes for each region to create objects. A genetic-based data mining was applied to generate high predictive and comprehensible classification rules based on selected samples from the OBIA result. Optimized intervals of relevant attributes are found, linked with land use types for forming classification rules. The unplanned areas were separated from the planned ones, through analyzing of the line segments detected from the input image. Finally a simple ontology was built based on the previous processing steps. The approach has been tested to VHR images of one of the biggest Algerian cities, that has grown considerably in recent decades.

  17. Passive micromechanical tags. An investigation into writing information at nanometer resolution on micrometer size objects

    International Nuclear Information System (INIS)

    Schmieder, R.W.; Bastasz, R.J.

    1995-01-01

    The authors have completed a 3-year study of the technology related to the development of micron-sized passive micromechanical tags. The project was motivated by the discovery in 1990 by the present authors that low energy, high charge state ions (e.g., Xe +44 ) can produce nanometer-size damage sites on solid surfaces, and the realization that a pattern of these sites represents information. It was envisioned that extremely small, chemically inert, mechanical tags carrying a large label could be fabricated for a variety of applications, including tracking of controlled substances, document verification, process control, research, and engineering. Potential applications exist in the data storage, chemical, food, security, and other industries. The goals of this project were fully accomplished, and they are fully documented here. The work was both experimental and developmental. Most of the experimental effort was a search for appropriate tag materials. Several good materials were found, and the upper limits of information density were determined (ca. 10 12 bit/cm 2 ). Most of the developmental work involved inventing systems and strategies for using these tags, and compiling available technologies for implementing them. The technology provided herein is application-specific: first, the application must be specified, then the tag can be developed for it. The project was not intended to develop a single tag for a single application or for all possible applications. Rather, it was meant to provide the enabling technology for fabricating tags for a range of applications. The results of this project provide sufficient information to proceed directly with such development

  18. Passive micromechanical tags. An investigation into writing information at nanometer resolution on micrometer size objects

    Energy Technology Data Exchange (ETDEWEB)

    Schmieder, R.W.; Bastasz, R.J.

    1995-01-01

    The authors have completed a 3-year study of the technology related to the development of micron-sized passive micromechanical tags. The project was motivated by the discovery in 1990 by the present authors that low energy, high charge state ions (e.g., Xe{sup +44}) can produce nanometer-size damage sites on solid surfaces, and the realization that a pattern of these sites represents information. It was envisioned that extremely small, chemically inert, mechanical tags carrying a large label could be fabricated for a variety of applications, including tracking of controlled substances, document verification, process control, research, and engineering. Potential applications exist in the data storage, chemical, food, security, and other industries. The goals of this project were fully accomplished, and they are fully documented here. The work was both experimental and developmental. Most of the experimental effort was a search for appropriate tag materials. Several good materials were found, and the upper limits of information density were determined (ca. 10{sup 12} bit/cm{sup 2}). Most of the developmental work involved inventing systems and strategies for using these tags, and compiling available technologies for implementing them. The technology provided herein is application-specific: first, the application must be specified, then the tag can be developed for it. The project was not intended to develop a single tag for a single application or for all possible applications. Rather, it was meant to provide the enabling technology for fabricating tags for a range of applications. The results of this project provide sufficient information to proceed directly with such development.

  19. Learning to Grasp Unknown Objects Based on 3D Edge Information

    DEFF Research Database (Denmark)

    Bodenhagen, Leon; Kraft, Dirk; Popovic, Mila

    2010-01-01

    In this work we refine an initial grasping behavior based on 3D edge information by learning. Based on a set of autonomously generated evaluated grasps and relations between the semi-global 3D edges, a prediction function is learned that computes a likelihood for the success of a grasp using either...... an offline or an online learning scheme. Both methods are implemented using a hybrid artificial neural network containing standard nodes with a sigmoid activation function and nodes with a radial basis function. We show that a significant performance improvement can be achieved....

  20. Learning from Balance Sheet Visualization

    Science.gov (United States)

    Tanlamai, Uthai; Soongswang, Oranuj

    2011-01-01

    This exploratory study examines alternative visuals and their effect on the level of learning of balance sheet users. Executive and regular classes of graduate students majoring in information technology in business were asked to evaluate the extent of acceptance and enhanced capability of these alternative visuals toward their learning…

  1. Intelligent Control System Taking Account of Cooperativeness Using Weighting Information on System Objective

    Directory of Open Access Journals (Sweden)

    Masaki Takahashi

    2004-08-01

    Full Text Available This study considers an intelligent control system to integrate flexibly its components by using weighted information where the system evaluation is reflected. Such system evaluates the information flowing through the components and converts them by weighting depending on the degree of importance. Integration of components based on the system evaluation enables a system consisting of them to realize various, flexible and adaptive control. In this study, the intelligent control method is applied to a swing up and stabilization control problem of a number of cart and pendulum systems on a restricted straight guide. To stabilize the pendulum in a restricted environment, each system should realize not only a swing-up and stabilization control of the pendulum, but also a position control of the cart to avoid collision or deadlock. The experiment using a real apparatus demonstrated that the controller learning light interaction acquires egoistic character, the controller learning heavy interaction behaves altruistically, and the controller equally considering self cart and another cart becomes cooperative. In other words, these autonomous decentralized controllers can acquire various characters and flexibility for cooperation.

  2. Objective classification of ecological status in marine water bodies using ecotoxicological information and multivariate analysis.

    Science.gov (United States)

    Beiras, Ricardo; Durán, Iria

    2014-12-01

    Some relevant shortcomings have been identified in the current approach for the classification of ecological status in marine water bodies, leading to delays in the fulfillment of the Water Framework Directive objectives. Natural variability makes difficult to settle fixed reference values and boundary values for the Ecological Quality Ratios (EQR) for the biological quality elements. Biological responses to environmental degradation are frequently of nonmonotonic nature, hampering the EQR approach. Community structure traits respond only once ecological damage has already been done and do not provide early warning signals. An alternative methodology for the classification of ecological status integrating chemical measurements, ecotoxicological bioassays and community structure traits (species richness and diversity), and using multivariate analyses (multidimensional scaling and cluster analysis), is proposed. This approach does not depend on the arbitrary definition of fixed reference values and EQR boundary values, and it is suitable to integrate nonlinear, sensitive signals of ecological degradation. As a disadvantage, this approach demands the inclusion of sampling sites representing the full range of ecological status in each monitoring campaign. National or international agencies in charge of coastal pollution monitoring have comprehensive data sets available to overcome this limitation.

  3. Information Interaction Criteria Among Students in Process of Task-Based Information Searching (Role of Objective Complexity and Type of Product

    Directory of Open Access Journals (Sweden)

    Marziyeh Saeedizadeh

    2016-08-01

    Full Text Available Purpose:  human-information interactions must be considered in order to be able to interactively design Information Retrieval Systems (IRS. In this regard, study of users’ interactions must be based on their socio-cultural context (specifically work tasks. Accordingly, this paper aims to explore the use of information-interaction criteria among students in the information searching process according to different kinds of their work tasks.  Methodology: This research is applied qualitative method using exploratory study. The research population consisted of MSc students of Ferdowsi university of Mashhad enrolled in 2012-13  academic year. In 3 stages of sampling (random stratified, quota, and voluntary sampling, 30 cases were selected. Each of these cases searched 6 different types of simulated work tasks. Interaction criteria were extracted ? Content analysis of aloud thinking reports. Validity of tools was verified through Faculties of KIS at Ferdowsi university of Mashhad. Also,0.78  Kripendorff’s alpha ratio based on an agreement between the inter – coder indicates the Dependability  of content analysis. Findings: The findings show that in addition to ‘topic’ criteria, other interaction criteria impact on information- interaction of users, such as: ‘search results ranking’, ‘domain knowledge of user’, ‘layout’, ‘type of information resource’ and etc. based on the level of objective complexity and product of  work tasks, information-interaction criteria change. Conclusion: the users pay attention to different information-interaction criteria in process of information searching, considering to variety of work tasks (level of objective complexity and product. So, it is necessary to pay attention to work task characteristics in order to design interactive and personalized IR systems.

  4. Someday I May Want to Know about...Leisure and Recreational Activities for Children and Adults with Mental Retardation. A MCARC Information Sheet.

    Science.gov (United States)

    Montgomery County Association for Retarded Citizens, Rockville, MD.

    The fact sheet considers the importance of recreation and leisure time activities for people with mental retardation. A case is made for mainstreamed services, and suggestions are offered for families seeking to procure successful mainstreamed experiences in community recreational programs. Among suggestions are adapting family games to the…

  5. ACCURACY EVALUATION OF THE OBJECT LOCATION VISUALIZATION FOR GEO-INFORMATION AND DISPLAY SYSTEMS OF MANNED AIRCRAFTS NAVIGATION COMPLEXES

    Directory of Open Access Journals (Sweden)

    M. O. Kostishin

    2014-01-01

    Full Text Available The paper deals with the issue of accuracy estimating for the object location display in the geographic information systems and display systems of manned aircrafts navigation complexes. Application features of liquid crystal screens with a different number of vertical and horizontal pixels are considered at displaying of geographic information data on different scales. Estimation display of navigation parameters values on board the aircraft is done in two ways: a numeric value is directly displayed on the screen of multi-color indicator, and a silhouette of the object is formed on the screen on a substrate background, which is a graphical representation of area map in the flight zone. Various scales of area digital map display currently used in the aviation industry have been considered. Calculation results of one pixel scale interval, depending on the specifications of liquid crystal screen and zoom of the map display area on the multifunction digital display, are given. The paper contains experimental results of the accuracy evaluation for area position display of the aircraft based on the data from the satellite navigation system and inertial navigation system, obtained during the flight program run of the real object. On the basis of these calculations a family of graphs was created for precision error display of the object reference point position using the onboard indicators with liquid crystal screen with different screen resolutions (6 "×8", 7.2 "×9.6", 9"×12" for two map display scales (1:0 , 25 km, 1-2 km. These dependency graphs can be used both to assess the error value of object area position display in existing navigation systems and to calculate the error value in upgrading facilities.

  6. Nanotechnology for Site Remediation: Fact Sheet

    Science.gov (United States)

    This fact sheet presents a snapshot of nanotechnology and its current uses in remediation. It presents information to help site project managers understand the potential applications of this group of technologies at their sites.

  7. Practical implementation of Wilhelm Osbahr’s entrepreneur balance sheet theory assumptions – the case study

    Directory of Open Access Journals (Sweden)

    Ewa Śnieżek

    2015-12-01

    Full Text Available The aim of this study is to present the possibilities of the practical application of Osbahr’s balance sheet theoryassumptions, as one of many possible attempts to close the information gap in the financial reporting of thetwenty-first century. Wilhelm Osbahr, at the beginning of the 20th century, made an attempt to solve the problemof indicating the balance sheet values (the impact of balance sheet evaluation on the balance sheet items,from the point of view of an entrepreneur or business owner, at the same time clearly emphasizing the necessityto deal with the balance sheet structure through the prism of the objectives pursued by the company. Osbahrpostulated highlighting any changes occurring in the economic structure of the company and its components,which do not result directly from its operating activities, and so to present them in the position called “adjustments”.This article uses the deductive method supported by literature studies and a case study method. Theauthors using the case study method confirm the possibility of using the described balance sheet theory in thecurrent financial reporting based on actual data of the company ABC Ltd. They also show that a balance sheetwhich is presented according to the new reporting formula discloses new quality of information for the financialreporting users.

  8. Evaluation of Randomly Selected Completed Medical Records Sheets in Teaching Hospitals of Jahrom University of Medical Sciences, 2009

    Directory of Open Access Journals (Sweden)

    Mohammad Parsa Mahjob

    2011-06-01

    Full Text Available Background and objective: Medical record documentation, often use to protect the patients legal rights, also providing information for medical researchers, general studies, education of health care staff and qualitative surveys is used. There is a need to control the amount of data entered in the medical record sheets of patients, considering the completion of these sheets is often carried out after completion of service delivery to the patients. Therefore, in this study the prevalence of completeness of medical history, operation reports, and physician order sheets by different documentaries in Jahrom teaching hospitals during year 2009 was analyzed. Methods and Materials: In this descriptive / retrospective study, the 400 medical record sheets of the patients from two teaching hospitals affiliated to Jahrom medical university was randomly selected. The tool of data collection was a checklist based on the content of medical history sheet, operation report and physician order sheets. The data were analyzed by SPSS (Version10 software and Microsoft Office Excel 2003. Results: Average of personal (Demography data entered in medical history, physician order and operation report sheets which is done by department's secretaries were 32.9, 35.8 and 40.18 percent. Average of clinical data entered by physician in medical history sheet is 38 percent. Surgical data entered by the surgeon in operation report sheet was 94.77 percent. Average of data entered by operation room's nurse in operation report sheet was 36.78 percent; Average of physician order data in physician order sheet entered by physician was 99.3 percent. Conclusion: According to this study, the rate of completed record papers reviewed by documentary in Jahrom teaching hospitals were not desirable and in some cases were very weak and incomplete. This deficiency was due to different reason such as medical record documentaries negligence, lack of adequate education for documentaries, High work

  9. Information-entropic stability bound for compact objects: Application to Q-balls and the Chandrasekhar limit of polytropes

    Energy Technology Data Exchange (ETDEWEB)

    Gleiser, Marcelo, E-mail: mgleiser@dartmouth.edu; Sowinski, Damian, E-mail: Damian.Sowinski.GR@dartmouth.edu

    2013-11-25

    Spatially-bound objects across diverse length and energy scales are characterized by a binding energy. We propose that their spatial structure is mathematically encoded as information in their momentum modes and described by a measure known as configurational entropy (CE) [1]. Investigating solitonic Q-balls and stars with a polytropic equation of state P=Kρ{sup γ}, we show that objects with large binding energy have low CE, whereas those at the brink of instability (zero binding energy) have near maximal CE. In particular, we use the CE to find the critical charge allowing for classically stable Q-balls and the Chandrasekhar limit for white dwarfs (γ=4/3) with an accuracy of a few percent.

  10. Order of the 30 December 2004 relative to the individual sheet of medical follow-up and to the individual information concerning the dosimetry of workers exposed to ionizing radiations; Arrete du 30 decembre 2004 relatif a la carte individuelle de suivi medical et aux informations individuelles de dosimetrie des travailleurs exposes aux rayonnements ionisants

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-12-15

    This order concerns the content and the modalities of grant of the individual sheet of medical follow-up, the collect and the centralization of dosimetry individual information by the Institute of Radiation Protection and Safety (IRSN), and the access to individual results of external and internal dosimetry. (A.L.B.)

  11. Methodology for Management of Information Security in Industrial Control Systems: A Proof of Concept aligned with Enterprise Objectives.

    Directory of Open Access Journals (Sweden)

    Fabian Bustamante

    2017-04-01

    Full Text Available This article is an extended version of the study presented at the IEEE Ecuador Technical Chapters Meeting (ETCM-2016. At that time, a methodological proposal was designed, implemented, and applied in a group of industrial plants for the management of the information security of the Industrial control systems (ICS. The present study displays an adaptation and improvement of such methodology with the purpose of aligning the proposal for the effective management of information security with the strategic objectives. The development of this study has been divided into three distinctive phases. Firstly, we induced the articulation of PMI-PMBOK v5 and ITIL v3 both for the management of the project and for the verification of risks in the IT services. Second, we applied a set of risk mitigation strategies based on international standards as NIST 800-82 and 800-30. Thirdly, we assembled the two mentioned phases in a Guide for standards-based instructions and security policies, which previously have been encouraged on NIST 800-82, 800-53 and 800-12. Hereby, we observed the reduction of incidents of information security, the correct delimitation of the functions of the direct responsible of the ICS and the improvement of the communication between the operative and technical areas of the involved companies. The results demonstrate the functionality of these improvements, especially in the context of the availability and integrity of information, which generates an added value to the enterprise.

  12. Libraries in Second Life: New Approaches to Education, Information Sharing, Learning Object Implementation, User Interactions and Collaborations

    Directory of Open Access Journals (Sweden)

    Susan Smith Nash

    2009-10-01

    Full Text Available Three-dimensional virtual worlds such as Second Life continue to expand the way they provide information, learning activities, and educational applications. This paper explores the types of learning activities that take place in Second Life and discusses how learning takes place, with a view toward developing effective instructional strategies. As learning objects are being launched in Second Life, new approaches to collaboration, interactivity, and cognition are being developed. Many learning-centered islands appeal to individuals who benefit from interaction with peers and instructors, and who can access learning objects such as information repositories, simulations, and interactive animations. The key advantages that Second Life offers include engaging and meaningful interaction with fellow learners, media-rich learning environments with embedded video, graphics, and interactive quizzes and assessments, an engaging environment for simulations such as virtual labs, and culturally inclusive immersive environments. However, because of the steep learning curve, technical difficulties, and cultural diversity, learners may become frustrated in Second Life. Since Second Life is social learning environment that emphasizes the creation of a self, effective learning requires step-by-step empowerment of that new, constructed self.

  13. Yearly energy balance sheets 1998-1999

    International Nuclear Information System (INIS)

    2001-01-01

    The objective of the presented statistics is to give a total picture of the Swedish energy supply and consumption 1998-1999. Compared to the regularly published energy balance sheets based on short periodic statistics, this publication is more disaggregated in the field of final energy consumption. The data are mainly based on yearly statistics on energy consumption in different sectors. The broad statistical base has made it possible to compile data for consumer categories on a fairly detailed level. In cases where direct statistical information is lacking or is insufficient, indirect calculation methods have been used for estimations or recalculations of basic statistics. Revisions and improvements of statistical sources as well as calculation methods will be performed successively. As a consequence of this, the statistics presented here could be revised in future publications

  14. Yearly energy balance sheets 1996-1998

    International Nuclear Information System (INIS)

    2000-01-01

    The objective of the presented statistics is to give a total picture of the Swedish energy supply and consumption 1996-1998. Compared to the regularly published energy balance sheets based on short periodic statistics, this publication is more disaggregated in the field of final energy consumption. The data are mainly based on yearly statistics on energy consumption in different sectors. The broad statistical base has made it possible to compile data for consumer categories on a fairly detailed level. In cases where direct statistical information is lacking or is insufficient, indirect calculation methods have been used for estimations or recalculations of basic statistics. Revisions and improvements of statistical sources as well as calculation methods will be performed successively. As a consequence of this, the statistics presented here could be revised in future publications

  15. Pygrass: An Object Oriented Python Application Programming Interface (API for Geographic Resources Analysis Support System (GRASS Geographic Information System (GIS

    Directory of Open Access Journals (Sweden)

    Marco Ciolli

    2013-03-01

    Full Text Available PyGRASS is an object-oriented Python Application Programming Interface (API for Geographic Resources Analysis Support System (GRASS Geographic Information System (GIS, a powerful open source GIS widely used in academia, commercial settings and governmental agencies. We present the architecture of the PyGRASS library, covering interfaces to GRASS modules, vector and raster data, with a focus on the new capabilities that it provides to GRASS users and developers. Our design concept of the module interface allows the direct linking of inputs and outputs of GRASS modules to create process chains, including compatibility checks, process control and error handling. The module interface was designed to be easily extended to work with remote processing services (Web Processing Service (WPS, Web Service Definition Language (WSDL/Simple Object Access Protocol (SOAP. The new object-oriented Python programming API introduces an abstract layer that opens the possibility to use and access transparently the efficient raster and vector functions of GRASS that are implemented in C. The design goal was to provide an easy to use, but powerful, Python interface for users and developers who are not familiar with the programming language C and with the GRASS C-API. We demonstrate the capabilities, scalability and performance of PyGRASS with several dedicated tests and benchmarks. We compare and discuss the results of the benchmarks with dedicated C implementations.

  16. A Workflow for Automated Satellite Image Processing: from Raw VHSR Data to Object-Based Spectral Information for Smallholder Agriculture

    Directory of Open Access Journals (Sweden)

    Dimitris Stratoulias

    2017-10-01

    Full Text Available Earth Observation has become a progressively important source of information for land use and land cover services over the past decades. At the same time, an increasing number of reconnaissance satellites have been set in orbit with ever increasing spatial, temporal, spectral, and radiometric resolutions. The available bulk of data, fostered by open access policies adopted by several agencies, is setting a new landscape in remote sensing in which timeliness and efficiency are important aspects of data processing. This study presents a fully automated workflow able to process a large collection of very high spatial resolution satellite images to produce actionable information in the application framework of smallholder farming. The workflow applies sequential image processing, extracts meaningful statistical information from agricultural parcels, and stores them in a crop spectrotemporal signature library. An important objective is to follow crop development through the season by analyzing multi-temporal and multi-sensor images. The workflow is based on free and open-source software, namely R, Python, Linux shell scripts, the Geospatial Data Abstraction Library, custom FORTRAN, C++, and the GNU Make utilities. We tested and applied this workflow on a multi-sensor image archive of over 270 VHSR WorldView-2, -3, QuickBird, GeoEye, and RapidEye images acquired over five different study areas where smallholder agriculture prevails.

  17. Ice sheet in peril

    DEFF Research Database (Denmark)

    Hvidberg, Christine Schøtt

    2016-01-01

    Earth's large ice sheets in Greenland and Antarctica are major contributors to sea level change. At present, the Greenland Ice Sheet (see the photo) is losing mass in response to climate warming in Greenland (1), but the present changes also include a long-term response to past climate transitions...

  18. Mobility Balance Sheet 2009

    International Nuclear Information System (INIS)

    Jorritsma, P.; Derriks, H.; Francke, J.; Gordijn, H.; Groot, W.; Harms, L.; Van der Loop, H.; Peer, S.; Savelberg, F.; Wouters, P.

    2009-06-01

    The Mobility Balance Sheet provides an overview of the state of the art of mobility in the Netherlands. In addition to describing the development of mobility this report also provides explanations for the growth of passenger and freight transport. Moreover, the Mobility Balance Sheet also focuses on a topical theme: the effects of economic crises on mobility. [nl

  19. The transposition of the balance sheet to financial and functional balance sheet. Research and development

    Directory of Open Access Journals (Sweden)

    Liana GĂDĂU

    2015-09-01

    Full Text Available As the title suggests, through this paper we want to highlight the necessity of treating again the content and the form of the balance sheet in order to adapt it to a more efficient analysis, this way surpassing the informational valences of the classic balance sheet. The functional and the financial balance sheet will be taken into account. These models of balance sheet permit the complex analyses regarding the solvability or the bankruptcy risk of an enterprise to take place, and also other analyses, like the analysis of the structure and the financial/ functional equilibrium, the analysis of the company on operating cycles and their role in the functioning of the company. Through the particularities offered by each of these two models of balance sheet, we want to present the advantages of a superior informing. This content of this material is based on a vast investigation of the specialized literature.

  20. Investigating the Potential of Using the Spatial and Spectral Information of Multispectral LiDAR for Object Classification

    Directory of Open Access Journals (Sweden)

    Wei Gong

    2015-09-01

    Full Text Available The abilities of multispectral LiDAR (MSL as a new high-potential active instrument for remote sensing have not been fully revealed. This study demonstrates the potential of using the spectral and spatial features derived from a novel MSL to discriminate surface objects. Data acquired with the MSL include distance information and the intensities of four wavelengths at 556, 670, 700, and 780 nm channels. A support vector machine was used to classify diverse objects in the experimental scene into seven types: wall, ceramic pots, Cactaceae, carton, plastic foam block, and healthy and dead leaves of E. aureum. Different features were used during classification to compare the performance of different detection systems. The spectral backscattered reflectance of one wavelength and distance represented the features from an equivalent single-wavelength LiDAR system; reflectance of the four wavelengths represented the features from an equivalent multispectral image with four bands. Results showed that the overall accuracy of using MSL data was as high as 88.7%, this value was 9.8%–39.2% higher than those obtained using a single-wavelength LiDAR, and 4.2% higher than for multispectral image.

  1. Balance Sheet Taxonomy

    Directory of Open Access Journals (Sweden)

    Ecaterina Necsulescu

    2011-05-01

    Full Text Available The general objective of the financial statements is to provide information about the financial position, financial performance and cash flows of an entity, information that is useful for a wide range of users. For the current paper is very interesting to take into account is the presentation of the important role given to assets even in defining the subject of accounting, both in economic and financial concept.

  2. Testing the construct validity of willingness to pay valuations using objective information about risk and health benefit.

    Science.gov (United States)

    Philips, Zoë; Whynes, David K; Avis, Mark

    2006-02-01

    This paper describes an experiment to test the construct validity of contingent valuation, by eliciting women's valuations for the NHS cervical cancer screening programme. It is known that, owing to low levels of knowledge of cancer and screening in the general population, women both over-estimate the risk of disease and the efficacy of screening. The study is constructed as a randomised experiment, in which one group is provided with accurate information about cervical cancer screening, whilst the other is not. The first hypothesis supporting construct validity, that controls who perceive greater benefits from screening will offer higher valuations, is substantiated. Both groups are then provided with objective information on an improvement to the screening programme, and are asked to value the improvement as an increment to their original valuations. The second hypothesis supporting construct validity, that controls who perceive the benefits of the programme to be high already will offer lower incremental valuations, is also substantiated. Copyright 2005 John Wiley & Sons, Ltd.

  3. Fuels planning: science synthesis and integration; social issues fact sheet 18: Issues affecting social acceptability of fuels treatments

    Science.gov (United States)

    Christine Esposito

    2006-01-01

    Researchers have tried to understand how information about forest management can influence a person's landscape preferences and aesthetic appreciation. These findings are relevant for fuels management projects, since these projects are often characterized by conflicts between aesthetic and ecological objectives. This fact sheet discusses different aspects and ways...

  4. [Rationalities of knowledge production: on transformations of objects, technologies and information in biomedicine and the life sciences].

    Science.gov (United States)

    Paul, Norbert W

    2009-09-01

    Since decades, scientific change has been interpreted in the light of paradigm shifts and scientific revolutions. The Kuhnian interpretation of scientific change however is now more and more confronted with non-disciplinary thinking in both, science and studies on science. This paper explores how research in biomedicine and the life sciences can be characterized by different rationalities, sometimes converging, sometimes contradictory, all present at the same time with varying ways of influence, impact, and visibility. In general, the rationality of objects is generated by fitting new objects and findings into a new experimental context. The rationality of hypotheses is a move towards the construction of novel explanatory tools and models. This is often inseparable meshing with the third, the technological rationality, in which a technology-driven, self-supporting and sometimes self-referential refinement of methods and technologies comes along with an extension into other fields. During the second and the third phase, the new and emerging fields tend to expand their explanatory reach not only across disciplinary boundaries but also into the social sphere, creating what has been characterized as "exceptionalism" (e.g. genetic exceptionalism or neuro-exceptionalism). Finally, recent biomedicine and life-sciences reach a level in which experimental work becomes more and more data-driven because the technologically constructed experimental systems generate a plethora of findings (data) which at some point start to blur the original hypotheses. For the rationality of information the materiality of research practices becomes secondary and research objects are more and more getting out of sight. Finally, the credibility of science as a practice becomes more and more dependent on consensus about the applicability and relevance of its results. The rationality of interest (and accountability) has become more and more characteristic for a research process which is no longer

  5. Carbon sheet pumping

    International Nuclear Information System (INIS)

    Ohyabu, N.; Sagara, A.; Kawamura, T.; Motojima, O.; Ono, T.

    1993-07-01

    A new hydrogen pumping scheme has been proposed which controls recycling of the particles for significant improvement of the energy confinement in toroidal magnetic fusion devices. In this scheme, a part of the vacuum vessel surface near the divertor is covered with carbon sheets of a large surface area. Before discharge initiation, the sheets are baked up to 700 ∼ 1000degC to remove the previously trapped hydrogen atoms. After being cooled down to below ∼ 200degC, the unsaturated carbon sheets trap high energy charge exchange hydrogen atoms effectively during a discharge and overall pumping efficiency can be as high as ∼ 50 %. (author)

  6. Anesthesia Fact Sheet

    Science.gov (United States)

    ... Education About NIGMS NIGMS Home > Science Education > Anesthesia Anesthesia Tagline (Optional) Middle/Main Content Area En español ... Version (464 KB) Other Fact Sheets What is anesthesia? Anesthesia is a medical treatment that prevents patients ...

  7. Structural Biology Fact Sheet

    Science.gov (United States)

    ... NIGMS NIGMS Home > Science Education > Structural Biology Structural Biology Tagline (Optional) Middle/Main Content Area PDF Version (688 KB) Other Fact Sheets What is structural biology? Structural biology is the study of how biological ...

  8. Radiation protecting sheet

    International Nuclear Information System (INIS)

    Makiguchi, Hiroshi.

    1989-01-01

    As protection sheets used in radioactivity administration areas, a thermoplastic polyurethane composition sheet with a thickness of less 0.5 mm, solid content (ash) of less than 5% and a shore D hardness of less than 60 is used. A composite sheet with thickness of less than 0.5 mm laminated or coated with such a thermoplastic polyurethane composition as a surface layer and the thermoplastic polyurethane composition sheet applied with secondary fabrication are used. This can satisfy all of the required properties, such as draping property, abrasion resistance, high breaking strength, necking resistance, endurance strength, as well as chemical resistance and easy burnability in burning furnace. Further, by forming uneveness on the surface by means of embossing, etc. safety problems such as slippage during operation and walking can be overcome. (T.M.)

  9. Single clay sheets inside electrospun polymer nanofibers

    Science.gov (United States)

    Sun, Zhaohui

    2005-03-01

    Nanofibers were prepared from polymer solution with clay sheets by electrospinning. Plasma etching, as a well controlled process, was used to supply electrically excited gas molecules from a glow discharge. To reveal the structure and arrangement of clay layers in the polymer matrix, plasma etching was used to remove the polymer by controlled gasification to expose the clay sheets due to the difference in reactivity. The shape, flexibility, and orientation of clay sheets were studied by transmission and scanning electron microscopy. Additional quantitative information on size distribution and degree of exfoliation of clay sheets were obtained by analyzing electron micrograph of sample after plasma etching. Samples in various forms including fiber, film and bulk, were thinned by plasma etching. Morphology and dispersion of inorganic fillers were studied by electron microscopy.

  10. Strontium-90 fluoride data sheet

    Energy Technology Data Exchange (ETDEWEB)

    Fullam, H.T.

    1981-06-01

    This report is a compilation of available data and appropriate literature references on the properties of strontium-90 fluoride and nonradioactive strontium fluoride. The objective of the document is to compile in a single source pertinent data to assist potential users in the development, licensing, and use of /sup 90/SrF/sub 2/-fueled radioisotope heat sources for terrestrial power conversion and thermal applications. The report is an update of the Strontium-90 Fluoride Data Sheet (BNWL-2284) originally issued in April 1977.

  11. Augmented reality system using lidar point cloud data for displaying dimensional information of objects on mobile phones

    Science.gov (United States)

    Gupta, S.; Lohani, B.

    2014-05-01

    Mobile augmented reality system is the next generation technology to visualise 3D real world intelligently. The technology is expanding at a fast pace to upgrade the status of a smart phone to an intelligent device. The research problem identified and presented in the current work is to view actual dimensions of various objects that are captured by a smart phone in real time. The methodology proposed first establishes correspondence between LiDAR point cloud, that are stored in a server, and the image t hat is captured by a mobile. This correspondence is established using the exterior and interior orientation parameters of the mobile camera and the coordinates of LiDAR data points which lie in the viewshed of the mobile camera. A pseudo intensity image is generated using LiDAR points and their intensity. Mobile image and pseudo intensity image are then registered using image registration method SIFT thereby generating a pipeline to locate a point in point cloud corresponding to a point (pixel) on the mobile image. The second part of the method uses point cloud data for computing dimensional information corresponding to the pairs of points selected on mobile image and fetch the dimensions on top of the image. This paper describes all steps of the proposed method. The paper uses an experimental setup to mimic the mobile phone and server system and presents some initial but encouraging results

  12. Using Information from Rendezvous Missions for Best-Case Appraisals of Impact Damage to Planet Earth Caused by Natural Objects

    Science.gov (United States)

    Arnold, James O.; Chodas, Paul W.; Ulamec, Stephan; Mathias, Donovan L.; Burkhard, Craig D.

    2017-01-01

    The Asteroid Threat Assessment Project (ATAP), a part of NASAs Planetary Defense Coordination Office (PDCO) has the responsibility to appraise the range of surface damage by potential asteroid impacts on land or water. If a threat is realized, the project will provide appraisals to officials empowered to make decisions about potential mitigation actions. This paper describes a scenario for assessment of surface damage when characterization of an asteroid had been accomplished by a rendezvous mission that would be conducted by the international planetary defense community. It is shown that the combination of data from ground and in-situ measurements on an asteroid provides knowledge that can be used to pin-point its impact location and predict the level of devastation it would cause. The hypothetical asteroid 2017 PDC with a size range of 160 to 290 m in diameter to be discussed at the PDC 2017 is used as an example. In order of importance for appraising potential damage, information required is: (1) where will the surface impact occur? (2) what is the mass, shape and size of the asteroid and what is its entry state (speed and entry angle) at the 100 km atmospheric pierce point? And (3) is the asteroid a monolith or a rubble pile? If it is a rubble pile, what is its structure and heterogeneity from the surface and throughout its interior? Item (1) is of first order importance to determine levels of devastation (loss of life and infrastructure damage) because it varies strongly on the impact location. Items (2) and (3) are used as inputs for ATAPs simulations to define the level of surface hazards: winds, overpressure, thermal exposure; all created by the deposition of energy during the objects atmospheric flight, andor cratering. Topics presented in this paper include: (i) the devastation predicted by 2017 PDCs impact on land based on initial observations using ATAPs risk assessment capability, (ii) how information corresponding to items (1) to (3) could be obtained

  13. MULTIPLE OBJECTS

    Directory of Open Access Journals (Sweden)

    A. A. Bosov

    2015-04-01

    Full Text Available Purpose. The development of complicated techniques of production and management processes, information systems, computer science, applied objects of systems theory and others requires improvement of mathematical methods, new approaches for researches of application systems. And the variety and diversity of subject systems makes necessary the development of a model that generalizes the classical sets and their development – sets of sets. Multiple objects unlike sets are constructed by multiple structures and represented by the structure and content. The aim of the work is the analysis of multiple structures, generating multiple objects, the further development of operations on these objects in application systems. Methodology. To achieve the objectives of the researches, the structure of multiple objects represents as constructive trio, consisting of media, signatures and axiomatic. Multiple object is determined by the structure and content, as well as represented by hybrid superposition, composed of sets, multi-sets, ordered sets (lists and heterogeneous sets (sequences, corteges. Findings. In this paper we study the properties and characteristics of the components of hybrid multiple objects of complex systems, proposed assessments of their complexity, shown the rules of internal and external operations on objects of implementation. We introduce the relation of arbitrary order over multiple objects, we define the description of functions and display on objects of multiple structures. Originality.In this paper we consider the development of multiple structures, generating multiple objects.Practical value. The transition from the abstract to the subject of multiple structures requires the transformation of the system and multiple objects. Transformation involves three successive stages: specification (binding to the domain, interpretation (multiple sites and particularization (goals. The proposed describe systems approach based on hybrid sets

  14. Are we reaching the target audience? Evaluation of a fish fact sheet.

    Science.gov (United States)

    Burger, J; Waishwell, L

    2001-09-28

    According to the US Environmental Protection Agency, over 16% of freshwater lakes and 7% of the rivers are under some sort of fish consumption advisory because of the presence of toxic chemicals. There is considerable interest in the issuing of information, advisories, and fact sheets concerning the consumption of wild-caught fish from contaminated waters, and in the actual consumption patterns of subsistence and recreational anglers. Despite the large number of consumption advisories issued by state agencies, there is little information on how these advisories, or other forms of risk communication, are perceived by target audiences, notably fishermen and women of child-bearing age. The states of South Carolina and Georgia issue consumption advisories for fish from the Savannah River, among other sites. To gain a greater insight into the perception of anglers about a supplemental fish fact sheet jointly developed by South Carolina, Georgia, federal agencies, and the Consortium for Risk Evaluation with Stakeholder Participation, we interviewed fisherman along the Savannah River. The objectives were to determine: (1) whether they had previously read the Fish Fact Sheet or had heard about the consumption advisories; (2) what major message they obtained from the sheet; (3) who they felt the fact sheet was aimed at, and who should get the Fish Fact Sheet; (4) who should be concerned about health risks from consuming the fish; and (5) the best method of disseminating such information. We interviewed 92 fishermen (37% black, 62% white) during the fishing season of 1999. Half had heard some information about consumption advisories, mainly from the media (64%). The study concluded that there were no ethnic differences in whether they had heard about the advisories, understood the major message of the fact sheet, felt they could reduce their risk from consuming the fish, or felt that it made a difference which agency issued the fact sheet. There were significant ethnic

  15. Audit of Provisions and Value Adjustments – a Very Important Objective for the Assessment of Information Comprised in the Financial Statements

    Directory of Open Access Journals (Sweden)

    Cristina IOVU

    2017-04-01

    Full Text Available Any type of entity must show in its financial statements information regarding its significant estimations concerning the future periods and other important sources of uncertainty at the date at which the financial statements are drafted, which presents an increased risk of generating an adjustment of the accounting value of the assets and debts in the future fiscal year. This information must include the nature of the estimations and their accounting value at the date of the balance sheet. The auditing of the financial statements in which accounting estimations are presented frame a high risk of significant distortion. Because of this, the auditor must obtain sufficient audit evidence which would certify if these estimations are reasonable, respectively if the data on which the estimations are based upon are accurate, complete and relevant, and the procedures and methods used for the development of the estimations are adequate for the balance sheet structures to which they apply. The development of provisions, as a manner to reflect uncertainties within the accounting system, contributes to the accurate representation of the company’s financial position. Such uncertainties are acknowledged through the presentation of their nature and value, but also through the exercising of prudence for the development of the financial statements. Prudence implies the identification of those accounting estimations, associated to the given uncertainties conditions, which would not over-evaluate the assets and the incomes, and the debts and expenses would not be under-evaluated. Exercising prudence should not allow, for instance, the accumulation of excessive provisions, the deliberate under-evaluation of assets and incomes, nor the deliberate over-evaluation of debts or expenses. This requirement is imperative, due to the fact that investors substantiate their economic decisions starting from the analysis of the financial statements, as accurate image of the

  16. Ice sheet hydrology from observations

    Energy Technology Data Exchange (ETDEWEB)

    Jansson, Peter [Dept. of Physical Geography and Quaternary Geology, Stockholm Univ-, Stockholm (Sweden)

    2010-11-15

    The hydrological systems of ice sheets are complex. Our view of the system is split, largely due to the complexity of observing the systems. Our basic knowledge of processes have been obtained from smaller glaciers and although applicable in general to the larger scales of the ice sheets, ice sheets contain features not observable on smaller glaciers due to their size. The generation of water on the ice sheet surface is well understood and can be satisfactorily modeled. The routing of water from the surface down through the ice is not complicated in terms of procat has been problematic is the way in which the couplings between surface and bed has been accomplished through a kilometer of cold ice, but with the studies on crack propagation and lake drainage on Greenland we are beginning to understand also this process and we know water can be routed through thick cold ice. Water generation at the bed is also well understood but the main problem preventing realistic estimates of water generation is lack of detailed information about geothermal heat fluxes and their geographical distribution beneath the ice. Although some average value for geothermal heat flux may suffice, for many purposes it is important that such values are not applied to sub-regions of significantly higher fluxes. Water generated by geothermal heat constitutes a constant supply and will likely maintain a steady system beneath the ice sheet. Such a system may include subglacial lakes as steady features and reconfiguration of the system is tied to time scales on which the ice sheet geometry changes so as to change pressure gradients in the basal system itself. Large scale re-organization of subglacial drainage systems have been observed beneath ice streams. The stability of an entirely subglacially fed drainage system may hence be perturbed by rapid ice flow. In the case of Antarctic ice streams where such behavior has been observed, the ice streams are underlain by deformable sediments. It is

  17. Ice sheet hydrology from observations

    International Nuclear Information System (INIS)

    Jansson, Peter

    2010-11-01

    The hydrological systems of ice sheets are complex. Our view of the system is split, largely due to the complexity of observing the systems. Our basic knowledge of processes have been obtained from smaller glaciers and although applicable in general to the larger scales of the ice sheets, ice sheets contain features not observable on smaller glaciers due to their size. The generation of water on the ice sheet surface is well understood and can be satisfactorily modeled. The routing of water from the surface down through the ice is not complicated in terms of procat has been problematic is the way in which the couplings between surface and bed has been accomplished through a kilometer of cold ice, but with the studies on crack propagation and lake drainage on Greenland we are beginning to understand also this process and we know water can be routed through thick cold ice. Water generation at the bed is also well understood but the main problem preventing realistic estimates of water generation is lack of detailed information about geothermal heat fluxes and their geographical distribution beneath the ice. Although some average value for geothermal heat flux may suffice, for many purposes it is important that such values are not applied to sub-regions of significantly higher fluxes. Water generated by geothermal heat constitutes a constant supply and will likely maintain a steady system beneath the ice sheet. Such a system may include subglacial lakes as steady features and reconfiguration of the system is tied to time scales on which the ice sheet geometry changes so as to change pressure gradients in the basal system itself. Large scale re-organization of subglacial drainage systems have been observed beneath ice streams. The stability of an entirely subglacially fed drainage system may hence be perturbed by rapid ice flow. In the case of Antarctic ice streams where such behavior has been observed, the ice streams are underlain by deformable sediments. It is

  18. Informational provision as the factor of effective cooperation between the subject and object in the system of business management

    OpenAIRE

    Netreba, I.

    2009-01-01

    The article reveals: ITsignificance for providing of effective communications in business management system; approach analysis for specification of such categories as "economic information", "information support", "information management system"; classification of economic information; reasons for introduction of integrated automation systems into management.

  19. Graphic-object information system {open_quotes}research base for reactor materials science{close_quotes}

    Energy Technology Data Exchange (ETDEWEB)

    Markina, N.V.; Lebedeva, E.E.; Arkhangel`skii, N.V.; Semenov, S.B.; Moiseev, A.L.

    1994-11-01

    An information system developed for reactor materials research is described. The information system incorporates an expert system, MATREKS, and a heirarchial data base. The data base contains information from 20 Russian research reactors. The information system structure, data base structure, search methods, system output modes, and technical facilities and software required are briefly discussed. 6 refs., 2 figs.

  20. Disintegration of liquid sheets

    Science.gov (United States)

    Mansour, Adel; Chigier, Norman

    1990-01-01

    The development, stability, and disintegration of liquid sheets issuing from a two-dimensional air-assisted nozzle is studied. Detailed measurements of mean drop size and velocity are made using a phase Doppler particle analyzer. Without air flow the liquid sheet converges toward the axis as a result of surface tension forces. With airflow a quasi-two-dimensional expanding spray is formed. The air flow causes small variations in sheet thickness to develop into major disturbances with the result that disruption starts before the formation of the main break-up region. In the two-dimensional variable geometry air-blast atomizer, it is shown that the air flow is responsible for the formation of large, ordered, and small chaotic 'cell' structures.

  1. Safety advice sheets

    CERN Multimedia

    HSE Unit

    2013-01-01

    You never know when you might be faced with questions such as: when/how should I dispose of a gas canister? Where can I find an inspection report? How should I handle/store/dispose of a chemical substance…?   The SI section of the DGS/SEE Group is primarily responsible for safety inspections, evaluating the safety conditions of equipment items, premises and facilities. On top of this core task, it also regularly issues “Safety Advice Sheets” on various topics, designed to be of assistance to users but also to recall and reinforce safety rules and procedures. These clear and concise sheets, complete with illustrations, are easy to display in the appropriate areas. The following safety advice sheets have been issued so far: Other sheets will be published shortly. Suggestions are welcome and should be sent to the SI section of the DGS/SEE Group. Please send enquiries to general-safety-visits.service@cern.ch.

  2. Constraints on Multiple Object Tracking in Williams Syndrome: How Atypical Development Can Inform Theories of Visual Processing

    Science.gov (United States)

    Ferrara, Katrina; Hoffman, James E.; O'Hearn, Kirsten; Landau, Barbara

    2016-01-01

    The ability to track moving objects is a crucial skill for performance in everyday spatial tasks. The tracking mechanism depends on representation of moving items as coherent entities, which follow the spatiotemporal constraints of objects in the world. In the present experiment, participants tracked 1 to 4 targets in a display of 8 identical…

  3. Ice Sheets & Ice Cores

    DEFF Research Database (Denmark)

    Mikkelsen, Troels Bøgeholm

    Since the discovery of the Ice Ages it has been evident that Earth’s climate is liable to undergo dramatic changes. The previous climatic period known as the Last Glacial saw large oscillations in the extent of ice sheets covering the Northern hemisphere. Understanding these oscillations known....... The first part concerns time series analysis of ice core data obtained from the Greenland Ice Sheet. We analyze parts of the time series where DO-events occur using the so-called transfer operator and compare the results with time series from a simple model capable of switching by either undergoing...

  4. Objective Tracking of Tropical Cyclones in the North-West Pacific Basin Based on Wind Field Information only

    Science.gov (United States)

    Leckebusch, G. C.; Befort, D. J.; Kruschke, T.

    2016-12-01

    Although only ca. 12% of the global insured losses of natural disasters occurred in Asia, there are two major reasons to be concerned about risks in Asia: a) The fraction of loss events was substantial higher with 39% of which 94% were due to atmospheric processes; b) Asia and especially China, is undergoing quick transitions and especially the insurance market is rapidly growing. In order to allow for the estimation of potential future (loss) impacts in East-Asia, in this study we further developed and applied a feature tracking system based on extreme wind speed occurrences to tropical cyclones, which was originally developed for extra-tropical cyclones (Leckebusch et al., 2008). In principle, wind fields will be identified and tracked once a coherent exceedance of local percentile thresholds is identified. The focus on severe wind impact will allow an objective link between the strength of a cyclone and its potential damages over land. The wind tracking is developed in such a way to be applicable also to course-gridded AOGCM simulation. In the presented configuration the wind tracking algorithm is applied to the Japanese reanalysis (JRA55) and TC Identification is based on 850hPa wind speeds (6h resolution) from 1979 to 2014 over the Western North Pacific region. For validation the IBTrACS Best Track archive version v03r8 is used. Out of all 904 observed tracks, about 62% can be matched to at least one windstorm event identified in JRA55. It is found that the relative amount of matched best tracks increases with the maximum intensity. Thus, a positive matching (hit rate) of above 98% for Violent Typhoons (VTY), above 90% for Very Strong Typhoons (VSTY), about 75% for Typhoons (TY), and still some 50% for less intense TCs (TD, TS, STS) is found. This result is extremely encouraging to apply this technique to AOGCM outputs and to derive information about affected regions and intensity-frequency distributions potentially changed under future climate conditions.

  5. Fact Sheets: Air Toxics Rules for the Manufacture of Amino/Phenolic Resins

    Science.gov (United States)

    This page contains a December 1999 fact sheet for the proposed National Emission Standards for Hazardous Air Pollutants (NESHAP): Manufacture of Amino/Phenolic Resins and a September 2014 fact sheet with information regarding the final NESHAP

  6. Forced tearing of ductile and brittle thin sheets.

    Science.gov (United States)

    Tallinen, T; Mahadevan, L

    2011-12-09

    Tearing a thin sheet by forcing a rigid object through it leads to complex crack morphologies; a single oscillatory crack arises when a tool is driven laterally through a brittle sheet, while two diverging cracks and a series of concertinalike folds forms when a tool is forced laterally through a ductile sheet. On the other hand, forcing an object perpendicularly through the sheet leads to radial petallike tears in both ductile and brittle materials. To understand these different regimes we use a combination of experiments, simulations, and simple theories. In particular, we describe the transition from brittle oscillatory tearing via a single crack to ductile concertina tearing with two tears by deriving laws that describe the crack paths and wavelength of the concertina folds and provide a simple phase diagram for the morphologies in terms of the material properties of the sheet and the relative size of the tool.

  7. Territorial Climate-Energy Plan - Le Mans region. Complete file + synthesis + Action sheets + Actor file + Appendices + Territory file

    International Nuclear Information System (INIS)

    Boulard, Jean-Claude

    2014-07-01

    A first document presents the meaning, objectives and implementation of the Territorial Climate Energy Plan (PCET) for Le Mans region, and then its five main steps: definition, diagnosis, actors, roadmap, assessment. A synthetic version is provided. Twenty action sheets are proposed, first in synthetic and general way, and then in terms of projects. These actions deal with transport and mobility, with building and development, with agriculture, forest and nature, with consumption and wastes, and with the mobilisation of actors. A document proposes sheets which describe good practices performed by Le Mans region 'syndicat mixte', by the city of Le Mans and its metropolitan body. Appendices contain some organisational information

  8. Collisionless current sheet equilibria

    Science.gov (United States)

    Neukirch, T.; Wilson, F.; Allanson, O.

    2018-01-01

    Current sheets are important for the structure and dynamics of many plasma systems. In space and astrophysical plasmas they play a crucial role in activity processes, for example by facilitating the release of magnetic energy via processes such as magnetic reconnection. In this contribution we will focus on collisionless plasma systems. A sensible first step in any investigation of physical processes involving current sheets is to find appropriate equilibrium solutions. The theory of collisionless plasma equilibria is well established, but over the past few years there has been a renewed interest in finding equilibrium distribution functions for collisionless current sheets with particular properties, for example for cases where the current density is parallel to the magnetic field (force-free current sheets). This interest is due to a combination of scientific curiosity and potential applications to space and astrophysical plasmas. In this paper we will give an overview of some of the recent developments, discuss their potential applications and address a number of open questions.

  9. Pseudomonas - Fact Sheet

    OpenAIRE

    Public Health Agency

    2012-01-01

    Fact sheet on Pseudomonas, including:What is Pseudomonas?What infections does it cause?Who is susceptible to pseudomonas infection?How will I know if I have pseudomonas infection?How can Pseudomonas be prevented from spreading?How can I protect myself from Pseudomonas?How is Pseudomonas infection treated?

  10. NTPR Fact Sheets

    Science.gov (United States)

    History Documents US Underground Nuclear Test History Reports NTPR Radiation Exposure Reports Enewetak Atoll Cleanup Documents TRAC About Who We Are Our Values History Locations Our Leadership Director Support Center Contact Us FAQ Sheet Links Success Stories Contracts Business Opportunities Current

  11. Hibernia fact sheet

    International Nuclear Information System (INIS)

    Anon.

    1994-01-01

    This fact sheet gives details of the Hibernia oil field including its location, discovery date, oil company's interests in the project, the recoverable reserves of the two reservoirs, the production system used, capital costs of the project, and overall targets for Canadian benefit. Significant dates for the Hibernia project are listed. (UK)

  12. Ethanol Basics (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2015-01-01

    Ethanol is a widely-used, domestically-produced renewable fuel made from corn and other plant materials. More than 96% of gasoline sold in the United States contains ethanol. Learn more about this alternative fuel in the Ethanol Basics Fact Sheet, produced by the U.S. Department of Energy's Clean Cities program.

  13. Silicon Sheet Quality is Improved By Meniscus Control

    Science.gov (United States)

    Yates, D. A.; Hatch, A. E.; Goldsmith, J. M.

    1983-01-01

    Better quality silicon crystals for solar cells are possible with instrument that monitors position of meniscus as sheet of solid silicon is drawn from melt. Using information on meniscus height, instrument generates feedback signal to control melt temperature. Automatic control ensures more uniform silicon sheets.

  14. Shape Optimization of Swimming Sheets

    Energy Technology Data Exchange (ETDEWEB)

    Wilkening, J.; Hosoi, A.E.

    2005-03-01

    The swimming behavior of a flexible sheet which moves by propagating deformation waves along its body was first studied by G. I. Taylor in 1951. In addition to being of theoretical interest, this problem serves as a useful model of the locomotion of gastropods and various micro-organisms. Although the mechanics of swimming via wave propagation has been studied extensively, relatively little work has been done to define or describe optimal swimming by this mechanism.We carry out this objective for a sheet that is separated from a rigid substrate by a thin film of viscous Newtonian fluid. Using a lubrication approximation to model the dynamics, we derive the relevant Euler-Lagrange equations to optimize swimming speed and efficiency. The optimization equations are solved numerically using two different schemes: a limited memory BFGS method that uses cubic splines to represent the wave profile, and a multi-shooting Runge-Kutta approach that uses the Levenberg-Marquardt method to vary the parameters of the equations until the constraints are satisfied. The former approach is less efficient but generalizes nicely to the non-lubrication setting. For each optimization problem we obtain a one parameter family of solutions that becomes singular in a self-similar fashion as the parameter approaches a critical value. We explore the validity of the lubrication approximation near this singular limit by monitoring higher order corrections to the zeroth order theory and by comparing the results with finite element solutions of the full Stokes equations.

  15. An activity theory analysis of boundary objects in cross-border information systems development for disaster management

    NARCIS (Netherlands)

    Bharosa, N.; Lee, J.; Janssen, M.; Rao, H.R.

    2012-01-01

    One of the main challenges in cross-border disaster management is the development and use of information systems that cater the needs of heterogeneous relief agencies, policies, activities and cultures. Drawing upon activity theory, this paper examines cross-border information systems development

  16. Automatic Generation of Object Models for Process Planning and Control Purposes using an International standard for Information Exchange

    Directory of Open Access Journals (Sweden)

    Petter Falkman

    2003-10-01

    Full Text Available In this paper a formal mapping between static information models and dynamic models is presented. The static information models are given according to an international standard for product, process and resource information exchange, (ISO 10303-214. The dynamic models are described as Discrete Event Systems. The product, process and resource information is automatically converted into product routes and used for simulation, controller synthesis and verification. A high level language, combining Petri nets and process algebra, is presented and used for speci- fication of desired routes. A main implication of the presented method is that it enables the reuse of process information when creating dynamic models for process control. This method also enables simulation and verification to be conducted early in the development chain.

  17. Chemical Data Reporting Fact Sheet: Chemicals Snapshot

    Science.gov (United States)

    This fact sheet provides a brief overview of the chemical manufacturing, processing, and use information collected for the 2012 Chemical Data Reporting (CDR) rule. Users do not have access to the complete CDR data set and should draw conclusions with care.

  18. Renewable Energy Project Development Assistance (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2013-07-01

    This fact sheet provides information on the Tribes selected to receive assistance from the U.S. Department of Energy Office of Indian Energy 2013 Strategic Technical Assistance Response Team (START) Program, which provides technical expertise to support the development of next-generation energy projects on tribal lands.

  19. Rapidly cast crystalline thin sheet materials

    International Nuclear Information System (INIS)

    Warlimont, H.; Emmerich, K.

    1986-01-01

    The current state and progress of casting thin sheet and ribbons directly from the melt are reviewed. First, the solidification phenomena pertinent to the process are outlined. Subsequently, Fe-Si,l Fe-Si-Al, Fe-Nd-B, Ag-Cu-Ti, alloy steels, Ni superalloys and Si are treated as examples. Finally, the information available on process development is critically assessed

  20. THE LANGUAGE LABORATORY--WORK SHEET.

    Science.gov (United States)

    CROSBIE, KEITH

    DESIGNED FOR TEACHERS AND ADMINISTRATORS, THIS WORK SHEET PROVIDES GENERAL AND SPECIFIC INFORMATION ABOUT THE PHILOSOPHY, TYPES, AND USES OF LANGUAGE LABORATORIES IN SECONDARY SCHOOL LANGUAGE PROGRAMS. THE FIRST SECTION DISCUSSES THE ADVANTAGES OF USING THE LABORATORY EFFECTIVELY TO REINFORCE AND CONSOLIDATE CLASSROOM LEARNING, AND MENTIONS SOME…

  1. Rubella - Fact Sheet for Parents

    Science.gov (United States)

    ... and 4 through 6 years Fact Sheet for Parents Color [2 pages] Español: Rubéola The best way ... according to the recommended schedule. Fact Sheets for Parents Diseases and the Vaccines that Prevent Them Chickenpox ...

  2. Effect of Temperature and Sheet Temper on Isothermal Solidification Kinetics in Clad Aluminum Brazing Sheet

    Science.gov (United States)

    Benoit, Michael J.; Whitney, Mark A.; Wells, Mary A.; Winkler, Sooky

    2016-09-01

    Isothermal solidification (IS) is a phenomenon observed in clad aluminum brazing sheets, wherein the amount of liquid clad metal is reduced by penetration of the liquid clad into the core. The objective of the current investigation is to quantify the rate of IS through the use of a previously derived parameter, the Interface Rate Constant (IRC). The effect of peak temperature and initial sheet temper on IS kinetics were investigated. The results demonstrated that IS is due to the diffusion of silicon (Si) from the liquid clad layer into the solid core. Reduced amounts of liquid clad at long liquid duration times, a roughened sheet surface, and differences in resolidified clad layer morphology between sheet tempers were observed. Increased IS kinetics were predicted at higher temperatures by an IRC model as well as by experimentally determined IRC values; however, the magnitudes of these values are not in good agreement due to deficiencies in the model when applied to alloys. IS kinetics were found to be higher for sheets in the fully annealed condition when compared with work-hardened sheets, due to the influence of core grain boundaries providing high diffusivity pathways for Si diffusion, resulting in more rapid liquid clad penetration.

  3. A Value of Information approach to data quality objectives for the Hanford high-level waste tanks

    International Nuclear Information System (INIS)

    Wood, T.W.; Hunter, V.L.; Ulvila, J.W.

    1995-02-01

    This report summarizes a Pacific Northwest Laboratory review of the organic-nitrate reaction safety issue in the Hanford single-shell tanks. This study employed a decision analytic method known as Value of Information (VOI). VOI analysis is a special form of decision analysis that has an information collection alternative as one of the initial decision choices. This type of decision analysis, therefore results in the ability to specify the preferred information collection alternative, taking into account all information gathering and other relevant alternatives. For example, the risk reduction benefit associated with further sampling to quantify total organic carbon inventory or to improve information on energetics can be compared to the risk reduction benefit of better temperature monitoring, operational restrictions, or mitigation by moisture control. This approach allows freedom from built-in assumptions, e.g., that all tanks must be sampled to some degree or that all tanks must be deemed intrinsically safe by some means or another. It allows for each tank management decision to be judged in terms of risk reduction from the current state of affairs, and for that state of affairs to be continuously updated to incorporate new information on tank contents, the phenomenology of safety issues, or the effectiveness of mitigation schemes

  4. High-Speed Tactile Sensing for Array-Type Tactile Sensor and Object Manipulation Based on Tactile Information

    Directory of Open Access Journals (Sweden)

    Wataru Fukui

    2011-01-01

    Full Text Available We have developed a universal robot hand with tactile and other sensors. An array-type tactile sensor is crucial for dexterous manipulation of objects using a robotic hand, since this sensor can measure the pressure distribution on finger pads. The sensor has a very high resolution, and the shape of a grasped object can be classified by using this sensor. The more the number of measurement points provided, the higher the accuracy of the classification, but with a corresponding lengthening of the measurement cycle. In this paper, the problem of slow response time is resolved by using software for an array-type tactile sensor with high resolution that emulates the human sensor system. The validity of the proposed method is demonstrated through experiments.

  5. Film sheet cassette

    International Nuclear Information System (INIS)

    1981-01-01

    A novel film sheet cassette is described for handling CAT photographic films under daylight conditions and facilitating their imaging. A detailed description of the design and operation of the cassette is given together with appropriate illustrations. The resulting cassette is a low-cost unit which is easily constructed and yet provides a sure light-tight seal for the interior contents of the cassette. The individual resilient fingers on the light-trap permit the ready removal of the slide plate for taking pictures. The stippled, non-electrostatic surface of the pressure plate ensures an air layer and free slidability of the film for removal and withdrawal of the film sheet. The advantage of the daylight system is that a darkroom need not be used for inserting and removing the film in and out of the cassette resulting in a considerable time saving. (U.K.)

  6. Augmented reality system using lidar point cloud data for displaying dimensional information of objects on mobile phones

    OpenAIRE

    Gupta, S.; Lohani, B.

    2014-01-01

    Mobile augmented reality system is the next generation technology to visualise 3D real world intelligently. The technology is expanding at a fast pace to upgrade the status of a smart phone to an intelligent device. The research problem identified and presented in the current work is to view actual dimensions of various objects that are captured by a smart phone in real time. The methodology proposed first establishes correspondence between LiDAR point cloud, that are stored in a ser...

  7. Persistent spatial information in the FEF during object-based short-term memory does not contribute to task performance.

    Science.gov (United States)

    Clark, Kelsey L; Noudoost, Behrad; Moore, Tirin

    2014-06-01

    We previously reported the existence of a persistent spatial signal in the FEF during object-based STM. This persistent activity reflected the location at which the sample appeared, irrespective of the location of upcoming targets. We hypothesized that such a spatial signal could be used to maintain or enhance object-selective memory activity elsewhere in cortex, analogous to the role of a spatial signal during attention. Here, we inactivated a portion of the FEF with GABAa agonist muscimol to test whether the observed activity contributes to object memory performance. We found that, although RTs were slowed for saccades into the inactivated portion of retinotopic space, performance for samples appearing in that region was unimpaired. This contrasts with the devastating effects of the same FEF inactivation on purely spatial working memory, as assessed with the memory-guided saccade task. Thus, in a task in which a significant fraction of FEF neurons displayed persistent, sample location-based activity, disrupting this activity had no impact on task performance.

  8. Biomolecular Science (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2012-04-01

    A brief fact sheet about NREL Photobiology and Biomolecular Science. The research goal of NREL's Biomolecular Science is to enable cost-competitive advanced lignocellulosic biofuels production by understanding the science critical for overcoming biomass recalcitrance and developing new product and product intermediate pathways. NREL's Photobiology focuses on understanding the capture of solar energy in photosynthetic systems and its use in converting carbon dioxide and water directly into hydrogen and advanced biofuels.

  9. Collection, transfer and processing of information in systems of monitoring of objects based on wireless sensor networks

    Directory of Open Access Journals (Sweden)

    Sergievskiy Maxim

    2016-01-01

    Full Text Available Monitoring of the aircraft structures’ during the pre-fiight testing is a critical task of the aerospace industry. One of the most promising solutions, not yet widely applied, is continuous monitoring of aircraft structures using wireless sensor network technology. The brief summary of the proposed system is the following: special sensors send signals to the local motes (autonomous computing device equipped with a wireless transmitter. Information from motes is gathered by routers which then transfer the aggregated information to the datacenter. Applications of corporate network control and define flexible patterns for processing of the information received from sensors. This network structure allows to centralize data collection modes in the process of testing; implement continuous data collection at a defined frequency; process and display data in real-time.

  10. Sheet pinch devices

    International Nuclear Information System (INIS)

    Anderson, O.A.; Baker, W.R.; Ise, J. Jr.; Kunkel, W.B.; Pyle, R.V.; Stone, J.M.

    1958-01-01

    Three types of sheet-like discharges are being studied at Berkeley. The first of these, which has been given the name 'Triax', consists of a cylindrical plasma sleeve contained between two coaxial conducting cylinders A theoretical analysis of the stability of the cylindrical sheet plasma predicts the existence of a 'sausage-mode' instability which is, however, expected to grow more slowly than in the case of the unstabilized linear pinch (by the ratio of the radial dimensions). The second pinch device employs a disk shaped discharge with radial current guided between flat metal plates, this configuration being identical to that of the flat hydromagnetic capacitor without external magnetic field. A significant feature of these configurations is the absence of a plasma edge, i.e., there are no regions of sharply curved magnetic field lines anywhere in these discharges. The importance of this fact for stability is not yet fully investigated theoretically. As a third configuration a rectangular, flat pinch tube has been constructed, and the behaviour of a flat plasma sheet with edges is being studied experimentally

  11. [The design and implementation of the web typical surface object spectral information system in arid areas based on .NET and SuperMap].

    Science.gov (United States)

    Xia, Jun; Tashpolat, Tiyip; Zhang, Fei; Ji, Hong-jiang

    2011-07-01

    The characteristic of object spectrum is not only the base of the quantification analysis of remote sensing, but also the main content of the basic research of remote sensing. The typical surface object spectral database in arid areas oasis is of great significance for applied research on remote sensing in soil salinization. In the present paper, the authors took the Ugan-Kuqa River Delta Oasis as an example, unified .NET and the SuperMap platform with SQL Server database stored data, used the B/S pattern and the C# language to design and develop the typical surface object spectral information system, and established the typical surface object spectral database according to the characteristics of arid areas oasis. The system implemented the classified storage and the management of typical surface object spectral information and the related attribute data of the study areas; this system also implemented visualized two-way query between the maps and attribute data, the drawings of the surface object spectral response curves and the processing of the derivative spectral data and its drawings. In addition, the system initially possessed a simple spectral data mining and analysis capabilities, and this advantage provided an efficient, reliable and convenient data management and application platform for the Ugan-Kuqa River Delta Oasis's follow-up study in soil salinization. Finally, It's easy to maintain, convinient for secondary development and practically operating in good condition.

  12. Curvature and the visual perception of shape: theory on information along object boundaries and the minima rule revisited.

    Science.gov (United States)

    Lim, Ik Soo; Leek, E Charles

    2012-07-01

    Previous empirical studies have shown that information along visual contours is known to be concentrated in regions of high magnitude of curvature, and, for closed contours, segments of negative curvature (i.e., concave segments) carry greater perceptual relevance than corresponding regions of positive curvature (i.e., convex segments). Lately, Feldman and Singh (2005, Psychological Review, 112, 243-252) proposed a mathematical derivation to yield information content as a function of curvature along a contour. Here, we highlight several fundamental errors in their derivation and in its associated implementation, which are problematic in both mathematical and psychological senses. Instead, we propose an alternative mathematical formulation for information measure of contour curvature that addresses these issues. Additionally, unlike in previous work, we extend this approach to 3-dimensional (3D) shape by providing a formal measure of information content for surface curvature and outline a modified version of the minima rule relating to part segmentation using curvature in 3D shape. Copyright 2012 APA, all rights reserved.

  13. A Workflow for Automated Satellite Image Processing : from Raw VHSR Data to Object-Based Spectral Information for Smallholder Agriculture

    NARCIS (Netherlands)

    Stratoulias, D.; Tolpekin, Valentyn; De By, Rolf; Zurita-milla, Raul; Retsios, Bas; Bijker, Wietske; Hasan, Mohammad; Vermote, Eric

    2017-01-01

    Earth Observation has become a progressively important source of information for land use and land cover services over the past decades. At the same time, an increasing number of reconnaissance satellites have been set in orbit with ever increasing spatial, temporal, spectral, and radiometric

  14. Hiding levitating objects above a ground plane

    DEFF Research Database (Denmark)

    Zhang, Jingjing; Luo, Yu; Mortensen, Asger

    2010-01-01

    An approach to hiding objects levitating above a conducting sheet is suggested in this paper. The proposed device makes use of isotropic negative-refractive-index materials without extreme material parameters, and creates an illusion of a remote conducting sheet. Numerical simulations are perform...

  15. Object and Objective Lost?

    DEFF Research Database (Denmark)

    Lopdrup-Hjorth, Thomas

    2015-01-01

    This paper explores the erosion and problematization of ‘the organization’ as a demarcated entity. Utilizing Foucault's reflections on ‘state-phobia’ as a source of inspiration, I show how an organization-phobia has gained a hold within Organization Theory (OT). By attending to the history...... of this organization-phobia, the paper argues that OT has become increasingly incapable of speaking about its core object. I show how organizations went from being conceptualized as entities of major importance to becoming theoretically deconstructed and associated with all kinds of ills. Through this history......, organizations as distinct entities have been rendered so problematic that they have gradually come to be removed from the center of OT. The costs of this have been rather significant. Besides undermining the grounds that gave OT intellectual credibility and legitimacy to begin with, the organization-phobia...

  16. Dense sheet Z-pinches

    International Nuclear Information System (INIS)

    Tetsu, Miyamoto

    1999-01-01

    The steady state and quasi-steady processes of infinite- and finite-width sheet z-pinches are studied. The relations corresponding to the Bennett relation and Pease-Braginskii current of cylindrical fiber z-pinches depend on a geometrical factor in the sheet z-pinches. The finite-width sheet z-pinch is approximated by a segment of infinite-width sheet z-pinch, if it is wide enough, and corresponds to a number of (width/thickness) times fiber z-pinch plasmas of the diameter that equals the sheet thickness. If the sheet current equals this number times the fiber current, the plasma created in the sheet z-pinches is as dense as in the fiber z-pinches. The total energy of plasma and magnetic field per unit mass is approximately equal in both pinches. Quasi-static transient processes are different in several aspects from the fiber z-pinch. No radiation collapse occurs in the sheet z-pinch. The stability is improved in the sheet z-pinches. The fusion criterions and the experimental arrangements to produce the sheet z-pinches are also discussed. (author)

  17. Perforation of metal sheets

    DEFF Research Database (Denmark)

    Steenstrup, Jens Erik

    simulation is focused on the sheet deformation. However, the effect on the tool and press is included. The process model is based on the upper bound analysis in order to predict the force progress and hole characteristics etc. Parameter analyses are divided into two groups, simulation and experimental tests......The main purposes of this project are:1. Development of a dynamic model for the piercing and performation process2. Analyses of the main parameters3. Establishing demands for process improvements4. Expansion of the existing parameter limitsThe literature survey describes the process influence...

  18. NASA/University JOint VEnture (JOVE) Program. VIXEN(tm): Object-Oriented, Technology-Adaptive, Virtual Information Exchange Environment

    Science.gov (United States)

    Anyiwo, Joshua C.

    2000-01-01

    Vixen is a collection of enabling technologies for uninhibited distributed object computing. In the Spring of 1995 when Vixen was proposed, it was an innovative idea very much ahead of its time. But today the technologies proposed in Vixen have become standard technologies for Enterprise Computing. Sun Microsystems J2EE/EJB specifications, among others, are independently proposed technologies of the Vixen type. I have brought Vixen completely under the J2EE standard in order to maximize interoperability and compatibility with other computing industry efforts. Vixen and the Enterprise JavaBean (EJB) Server technologies are now practically identical; OIL, another Vixen technology, and the Java Messaging System (JMS) are practically identical; and so on. There is no longer anything novel or patentable in the Vixen work performed under this grant. The above discussion, notwithstanding, my independent development of Vixen has significantly helped me, my university, my students and the local community. The undergraduate students who worked with me in developing Vixen have enhanced their expertise in what has become the cutting edge technology of their industry and are therefore well positioned for lucrative employment opportunities in the industry. My academic department has gained a new course: "Multi-media System Development", which provides a highly desirable expertise to our students for employment in any enterprise today. The many Outreach Programs that I conducted during this grant period have exposed local Middle School students to the contributions that NASA is making in our society as well as awakened desires in many such students for careers in Science and Technology. I have applied Vixen to the development of two software packages: (a) JAS: Joshua Application Server - which allows a user to configure an EJB Server to serve a J2EE compliant application over the world wide web; (b) PCM: Professor Course Manager: a J2EE compliant application for configuring a

  19. Application of Digital Object Identifiers to data sets at the NASA Goddard Earth Sciences Data and Information Services Center (GES DISC)

    Science.gov (United States)

    Vollmer, B.; Ostrenga, D.; Johnson, J. E.; Savtchenko, A. K.; Shen, S.; Teng, W. L.; Wei, J. C.

    2013-12-01

    Digital Object Identifiers (DOIs) are applied to selected data sets at the NASA Goddard Earth Sciences Data and Information Services Center (GES DISC). The DOI system provides an Internet resolution service for unique and persistent identifiers of digital objects. Products assigned DOIs include data from the NASA MEaSUREs Program, the Earth Observing System (EOS) Aqua Atmospheric Infrared Sounder (AIRS) and EOS Aura High Resolution Dynamics Limb Sounder (HIRDLS). DOIs are acquired and registered through EZID, California Digital Library and DataCite. GES DISC hosts a data set landing page associated with each DOI containing information on and access to the data including a recommended data citation when using the product in research or applications. This work includes participation with the earth science community (e.g., Earth Science Information Partners (ESIP) Federation) and the NASA Earth Science Data and Information System (ESDIS) Project to identify, establish and implement best practices for assigning DOIs and managing supporting information, including metadata, for earth science data sets. Future work includes (1) coordination with NASA mission Science Teams and other data providers on the assignment of DOIs for other GES DISC data holdings, particularly for future missions such as Orbiting Carbon Observatory -2 and -3 (OCO-2, OCO-3) and projects (MEaSUREs 2012), (2) construction of landing pages that are both human and machine readable, and (3) pursuing the linking of data and publications with tools such as the Thomson Reuters Data Citation Index.

  20. Experiments on sheet metal shearing

    OpenAIRE

    Gustafsson, Emil

    2013-01-01

    Within the sheet metal industry, different shear cutting technologies are commonly used in several processing steps, e.g. in cut to length lines, slitting lines, end cropping etc. Shearing has speed and cost advantages over competing cutting methods like laser and plasma cutting, but involves large forces on the equipment and large strains in the sheet material.Numerical models to predict forces and sheared edge geometry for different sheet metal grades and different shear parameter set-ups a...

  1. Limit State of Trapezoidal Metal Sheets Exposed to Concentrated Load

    OpenAIRE

    Kateřina Jurdová

    2013-01-01

    In most industrial compounds are used trapezoidal metal sheets like a roof decks. These trapezoidal metal sheets are exposed by concentrated loads, usually by service loads arise from installation of air distribution, sanitary distribution, sprinkler system or wiring installation. In objects of public facilities (like shopping centre, tennis hall, etc.) they can be used for hanging advertising posters etc, too. These systems work as “building kit”. These anchoring systems are represented by c...

  2. 14 CFR Section 6 - Objective Classification of Balance Sheet Elements

    Science.gov (United States)

    2010-01-01

    ... and reused; (2) Unissued fuel inventories for use in the overall or system operations of the carrier... and office supplies, passenger service supplies, and restaurant and food service supplies. (b) Costs... operations shall be charged to operating expenses as issued and shall not be charged to this account. If at...

  3. Honey Do Franchising Group, Inc. Information Sheet

    Science.gov (United States)

    Honey Do Franchising Group, Inc., a/k/a The Honey Do Service, Inc. (the Company) is located in Bristol, Virginia. The settlement involves renovation activities conducted at properties constructed prior to 1978, located in Bristol, Virginia.

  4. NARRAGANSETT-3VS MODEL OVERVIEW (Information Sheet)

    Science.gov (United States)

    In an effort to advance sustainability, EPA Region 1 (New England) and the EPA Office of Research and Development (ORD) are collaborating on a project to address the problem of nutrient impairment to ecological functions in sensitive waterways. The project is based on the Triple...

  5. Scott Brothers Windows and Doors Information Sheet

    Science.gov (United States)

    Scott Brothers Windows and Doors (the Company) is located in Bridgeville, Pennsylvania. The settlement involves renovation activities conducted at property constructed prior to 1978, located in Pittsburgh, Pennsylvania.

  6. Upstate Windows and Exteriors Information Sheet

    Science.gov (United States)

    Upstate Windows and Exteriors (the Company) is located in Greenville, South Carolina. The settlement involves renovation activities conducted at properties constructed prior to 1978, located in Greenville and Easley, South Carolina.

  7. Mangold Property Management, Inc. Information Sheet

    Science.gov (United States)

    Mangold Property Management, Inc. (the Company) is located in Monterey, California. The settlement involves the lease of properties constructed prior to 1978, located in Salinas and Monterey, California.

  8. Zidan Management Group, Inc. Information Sheet

    Science.gov (United States)

    Zidan Management Group, Inc. (the Company) is located in Indianapolis, Indiana. The settlement involves renovation activities conducted at property constructed prior to 1978, located in Kalamazoo, Michigan.

  9. VB Platinum Tile & Carpet, Inc. Information Sheet

    Science.gov (United States)

    VB Platinum Tile & Carpet, Inc. (the Company) is located in Bristow, Virginia. The settlement involves renovation activities conducted at a property constructed prior to 1978, located in Washington, DC.

  10. Tom Ford Construction, LLC Information Sheet

    Science.gov (United States)

    Tom Ford Construction, LLC (the Company) is located in Brentwood, Tennessee. The settlement involves renovation activities conducted at a property constructed prior to 1978, located in Nashville, Tennessee.

  11. Strategic Planning. Alliance Action Information Sheets

    Science.gov (United States)

    Technical Assistance ALLIANCE for Parent Centers, 2005

    2005-01-01

    Executive Directors of parent centers have very challenging careers. For example, they need to ensure that high quality services are developed and provided; funds are raised; bills are paid on time; staff are hired, trained and supported; boards are recruited and effective; community awareness is high; and reports are accurate and submitted on…

  12. Sears Home Improvement Products, Inc. Information Sheet

    Science.gov (United States)

    Sears Home Improvement Products, Inc. (the Company) is located in Longwood, Florida. The case involves renovation activities conducted at property constructed prior to 1978, located in cities across Minnesota, Wisconsin, California, Georgia, Nevada.

  13. Economy Home Improvement, Inc. Information Sheet

    Science.gov (United States)

    Economy Home Improvement, Inc. (the Company) is located in Lexington, Kentucky. The settlement involves renovation activities conducted at a property constructed prior to 1978, located in Lexington, Kentucky.

  14. St. Laurent Construction Co., Inc. Information Sheet

    Science.gov (United States)

    St. Laurent Construction Co., Inc. (the Company) is located in Nashua, New Hampshire. The settlement involves renovation activities conducted at properties constructed prior to 1978, located in Merrimack and Nashua, New Hampshire.

  15. RA Construction KC, LLC Information Sheet

    Science.gov (United States)

    RA Construction KC, LLC (the Company) is located in Gladstone, Missouri. The settlement involves renovation activities conducted at a property constructed prior to 1978, located in Kansas City, Missouri.

  16. Maryland Cleaning & Abatement Services Corp. Information Sheet

    Science.gov (United States)

    Maryland Cleaning & Abatement Services Corp. (the Company) is located in Baltimore, Maryland. The settlement involves renovation activities conducted at property constructed prior to 1978, located in Baltimore, Maryland.

  17. Soft Costs Fact Sheet

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-05-01

    This fact sheet is an overview of the systems integration subprogram at the U.S. Department of Energy SunShot Initiative. Soft costs can vary significantly as a result of a fragmented energy marketplace. In the U.S., there are 18,000 jurisdictions and 3,000 utilities with different rules and regulations for how to go solar. The same solar equipment may vary widely in its final installation price due to process and market variations across jurisdictions, creating barriers to rapid industry growth. SunShot supports the development of innovative solutions that enable communities to build their local economies and establish clean energy initiatives that meet their needs, while at the same time creating sustainable solar market conditions.

  18. Photovoltaics Fact Sheet

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-02-01

    This fact sheet is an overview of the Photovoltaics (PV) subprogram at the U.S. Department of Energy SunShot Initiative. The U.S. Department of Energy (DOE)’s Solar Energy Technologies Office works with industry, academia, national laboratories, and other government agencies to advance solar PV, which is the direct conversion of sunlight into electricity by a semiconductor, in support of the goals of the SunShot Initiative. SunShot supports research and development to aggressively advance PV technology by improving efficiency and reliability and lowering manufacturing costs. SunShot’s PV portfolio spans work from early-stage solar cell research through technology commercialization, including work on materials, processes, and device structure and characterization techniques.

  19. Systems Integration Fact Sheet

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-06-01

    This fact sheet is an overview of the Systems Integration subprogram at the U.S. Department of Energy SunShot Initiative. The Systems Integration subprogram enables the widespread deployment of safe, reliable, and cost-effective solar energy technologies by addressing the associated technical and non-technical challenges. These include timely and cost-effective interconnection procedures, optimal system planning, accurate prediction of solar resources, monitoring and control of solar power, maintaining grid reliability and stability, and many more. To address the challenges associated with interconnecting and integrating hundreds of gigawatts of solar power onto the electricity grid, the Systems Integration program funds research, development, and demonstration projects in four broad, interrelated focus areas: grid performance and reliability, dispatchability, power electronics, and communications.

  20. Hyperspectral light sheet microscopy

    Science.gov (United States)

    Jahr, Wiebke; Schmid, Benjamin; Schmied, Christopher; Fahrbach, Florian O.; Huisken, Jan

    2015-09-01

    To study the development and interactions of cells and tissues, multiple fluorescent markers need to be imaged efficiently in a single living organism. Instead of acquiring individual colours sequentially with filters, we created a platform based on line-scanning light sheet microscopy to record the entire spectrum for each pixel in a three-dimensional volume. We evaluated data sets with varying spectral sampling and determined the optimal channel width to be around 5 nm. With the help of these data sets, we show that our setup outperforms filter-based approaches with regard to image quality and discrimination of fluorophores. By spectral unmixing we resolved overlapping fluorophores with up to nanometre resolution and removed autofluorescence in zebrafish and fruit fly embryos.

  1. Settlement during vibratory sheet piling

    NARCIS (Netherlands)

    Meijers, P.

    2007-01-01

    During vibratory sheet piling quite often the soil near the sheet pile wall will settle. In many cases this is not a problem. For situations with houses, pipelines, roads or railroads at relative short distance these settlements may not be acceptable. The purpose of the research described in this

  2. Visual long-term memory and change blindness: Different effects of pre- and post-change information on one-shot change detection using meaningless geometric objects.

    Science.gov (United States)

    Nishiyama, Megumi; Kawaguchi, Jun

    2014-11-01

    To clarify the relationship between visual long-term memory (VLTM) and online visual processing, we investigated whether and how VLTM involuntarily affects the performance of a one-shot change detection task using images consisting of six meaningless geometric objects. In the study phase, participants observed pre-change (Experiment 1), post-change (Experiment 2), or both pre- and post-change (Experiment 3) images appearing in the subsequent change detection phase. In the change detection phase, one object always changed between pre- and post-change images and participants reported which object was changed. Results showed that VLTM of pre-change images enhanced the performance of change detection, while that of post-change images decreased accuracy. Prior exposure to both pre- and post-change images did not influence performance. These results indicate that pre-change information plays an important role in change detection, and that information in VLTM related to the current task does not always have a positive effect on performance. Copyright © 2014 Elsevier Inc. All rights reserved.

  3. Plasma dynamics in current sheets

    International Nuclear Information System (INIS)

    Bogdanov, S.Yu.; Drejden, G.V.; Kirij, N.P.; AN SSSR, Leningrad

    1992-01-01

    Plasma dynamics in successive stages of current sheet evolution is investigated on the base of analysis of time-spatial variations of electron density and electrodynamic force fields. Current sheet formation is realized in a two-dimensional magnetic field with zero line under the action of relatively small initial disturbances (linear regimes). It is established that in the limits of the formed sheet is concentrated dense (N e ∼= 10 16 cm -3 ) (T i ≥ 100 eV, bar-Z i ≥ 2) hot pressure of which is balanced by the magnetic action of electrodynamic forces is carried out both plasma compression in the sheet limits and the acceleration along the sheet surface from a middle to narrow side edges

  4. A Knowledge-Informed and Pareto-Based Artificial Bee Colony Optimization Algorithm for Multi-Objective Land-Use Allocation

    Directory of Open Access Journals (Sweden)

    Lina Yang

    2018-02-01

    Full Text Available Land-use allocation is of great significance in urban development. This type of allocation is usually considered to be a complex multi-objective spatial optimization problem, whose optimized result is a set of Pareto-optimal solutions (Pareto front reflecting different tradeoffs in several objectives. However, obtaining a Pareto front is a challenging task, and the Pareto front obtained by state-of-the-art algorithms is still not sufficient. To achieve better Pareto solutions, taking the grid-representative land-use allocation problem with two objectives as an example, an artificial bee colony optimization algorithm for multi-objective land-use allocation (ABC-MOLA is proposed. In this algorithm, the traditional ABC’s search direction guiding scheme and solution maintaining process are modified. In addition, a knowledge-informed neighborhood search strategy, which utilizes the auxiliary knowledge of natural geography and spatial structures to facilitate the neighborhood spatial search around each solution, is developed to further improve the Pareto front’s quality. A series of comparison experiments (a simulated experiment with small data volume and a real-world data experiment for a large area shows that all the Pareto fronts obtained by ABC-MOLA totally dominate the Pareto fronts by other algorithms, which demonstrates ABC-MOLA’s effectiveness in achieving Pareto fronts of high quality.

  5. The Efficacy of a Silicone Sheet in Postoperative Scar Management.

    Science.gov (United States)

    Kim, Jin Sam; Hong, Joon Pio; Choi, Jong Woo; Seo, Dong Kyo; Lee, Eun Sook; Lee, Ho Seong

    2016-09-01

    Silicone gel sheeting has been introduced to prevent scarring, but objective evidence for its usefulness in scar healing is limited. Therefore, the authors' objective was to examine the effectiveness of silicone gel sheeting by randomly applying it to only unilateral scars from a bilateral hallux valgus surgery with symmetrical closure. In a prospective randomized, blinded, intraindividual comparison study, the silicone gel sheeting was applied to 1 foot of a hallux valgus incision scar (an experiment group) for 12 weeks upon removal of the stitches, whereas the symmetrical scar from the other foot was left untreated (a control group). The scars were evaluated at 4 and 12 weeks after the silicon sheet application. The Vancouver Scar Scale was used to measure the vascularity, pigmentation, pliability, height, and length of the scars. Adverse effects were also evaluated, and they included pain, itchiness, rash, erythema, and skin softening. At weeks 4 and 12, the experiment group scored significantly better on the Vancouver Scar Scale in all items, except length (P sheet does not cause adverse effects (P sheet application did show a significant improvement in prevention of postoperative scarring.

  6. Flat-plate solar array project. Volume 3: Silicon sheet: Wafers and ribbons

    Science.gov (United States)

    Briglio, A.; Dumas, K.; Leipold, M.; Morrison, A.

    1986-01-01

    The primary objective of the Silicon Sheet Task of the Flat-Plate Solar Array (FSA) Project was the development of one or more low cost technologies for producing silicon sheet suitable for processing into cost-competitive solar cells. Silicon sheet refers to high purity crystalline silicon of size and thickness for fabrication into solar cells. Areas covered in the project were ingot growth and casting, wafering, ribbon growth, and other sheet technologies. The task made and fostered significant improvements in silicon sheet including processing of both ingot and ribbon technologies. An additional important outcome was the vastly improved understanding of the characteristics associated with high quality sheet, and the control of the parameters required for higher efficiency solar cells. Although significant sheet cost reductions were made, the technology advancements required to meet the task cost goals were not achieved.

  7. DOI - Digital Object Identifier : A revolution in the management and trading of copyrighted information over the Internet in the third millenium

    Directory of Open Access Journals (Sweden)

    Martin Žnideršič

    1997-01-01

    Full Text Available Rapid development of information technology in recent years has brought over also the problem of the protection of author's rights related to copyrighted works on electronic media. Information and law specialists were intensively working on this problem for several years and the result has been a new system of labelling copyrighted works on the Internet, called DOI (Digitial Object Identifier. The system was developed in the United States. At the time of the presenta tion of DOI at the Bookfair in Frankfurt, 250.000 author works were labelled with DOI. The system is universal and enables the inclusion of the present standard identifiers (ISBN, ISSN, SICI. The fact that DOI identifier stays "glued on" forever, makes the identification of the carrier of copyright possible at any moment. The DOI system presents the infrastructure system for trading in and use of copyrighted works over the Internet in the third millenium.

  8. Rett Syndrome Fact Sheet

    Science.gov (United States)

    ... help them maintain adequate weight. Special academic, social, vocational, and support services may be required in some ... Are Funded Small Business Grants Overview Areas of Interest Budget Information Grant Timeline Award Information Entrepreneurial Resources ...

  9. Selectively reflective transparent sheets

    Science.gov (United States)

    Waché, Rémi; Florescu, Marian; Sweeney, Stephen J.; Clowes, Steven K.

    2015-08-01

    We investigate the possibility to selectively reflect certain wavelengths while maintaining the optical properties on other spectral ranges. This is of particular interest for transparent materials, which for specific applications may require high reflectivity at pre-determined frequencies. Although there exist currently techniques such as coatings to produce selective reflection, this work focuses on new approaches for mass production of polyethylene sheets which incorporate either additives or surface patterning for selective reflection between 8 to 13 μ m. Typical additives used to produce a greenhouse effect in plastics include particles such as clays, silica or hydroxide materials. However, the absorption of thermal radiation is less efficient than the decrease of emissivity as it can be compared with the inclusion of Lambertian materials. Photonic band gap engineering by the periodic structuring of metamaterials is known in nature for producing the vivid bright colors in certain organisms via strong wavelength-selective reflection. Research to artificially engineer such structures has mainly focused on wavelengths in the visible and near infrared. However few studies to date have been carried out to investigate the properties of metastructures in the mid infrared range even though the patterning of microstructure is easier to achieve. We present preliminary results on the diffuse reflectivity using FDTD simulations and analyze the technical feasibility of these approaches.

  10. The Rapid Ice Sheet Change Observatory (RISCO)

    Science.gov (United States)

    Morin, P.; Howat, I. M.; Ahn, Y.; Porter, C.; McFadden, E. M.

    2010-12-01

    The recent expansion of observational capacity from space has revealed dramatic, rapid changes in the Earth’s ice cover. These discoveries have fundamentally altered how scientists view ice-sheet change. Instead of just slow changes in snow accumulation and melting over centuries or millennia, important changes can occur in sudden events lasting only months, weeks, or even a single day. Our understanding of these short time- and space-scale processes, which hold important implications for future global sea level rise, has been impeded by the low temporal and spatial resolution, delayed sensor tasking, incomplete coverage, inaccessibility and/or high cost of data available to investigators. New cross-agency partnerships and data access policies provide the opportunity to dramatically improve the resolution of ice sheet observations by an order of magnitude, from timescales of months and distances of 10’s of meters, to days and meters or less. Advances in image processing technology also enable application of currently under-utilized datasets. The infrastructure for systematically gathering, processing, analyzing and distributing these data does not currently exist. Here we present the development of a multi-institutional, multi-platform observatory for rapid ice change with the ultimate objective of helping to elucidate the relevant timescales and processes of ice sheet dynamics and response to climate change. The Rapid Ice Sheet Observatory (RISCO) gathers observations of short time- and space-scale Cryosphere events and makes them easily accessible to investigators, media and general public. As opposed to existing data centers, which are structured to archive and distribute diverse types of raw data to end users with the specialized software and skills to analyze them, RISCO focuses on three types of geo-referenced raster (image) data products in a format immediately viewable with commonly available software. These three products are (1) sequences of images

  11. Characterization of Tensile Mechanical Behavior of MSCs/PLCL Hybrid Layered Sheet

    Directory of Open Access Journals (Sweden)

    Azizah Intan Pangesty

    2016-06-01

    Full Text Available A layered construct was developed by combining a porous polymer sheet and a cell sheet as a tissue engineered vascular patch. The primary objective of this study is to investigate the influence of mesenchymal stem cells (MSCs sheet on the tensile mechanical properties of porous poly-(l-lactide-co-ε-caprolactone (PLCL sheet. The porous PLCL sheet was fabricated by the solid-liquid phase separation method and the following freeze-drying method. The MSCs sheet, prepared by the temperature-responsive dish, was then layered on the top of the PLCL sheet and cultured for 2 weeks. During the in vitro study, cellular properties such as cell infiltration, spreading and proliferation were evaluated. Tensile test of the layered construct was performed periodically to characterize the tensile mechanical behavior. The tensile properties were then correlated with the cellular properties to understand the effect of MSCs sheet on the variation of the mechanical behavior during the in vitro study. It was found that MSCs from the cell sheet were able to migrate into the PLCL sheet and actively proliferated into the porous structure then formed a new layer of MSCs on the opposite surface of the PLCL sheet. Mechanical evaluation revealed that the PLCL sheet with MSCs showed enhancement of tensile strength and strain energy density at the first week of culture which is characterized as the effect of MSCs proliferation and its infiltration into the porous structure of the PLCL sheet. New technique was presented to develop tissue engineered patch by combining MSCs sheet and porous PLCL sheet, and it is expected that the layered patch may prolong biomechanical stability when implanted in vivo.

  12. Analysis of the Strength on the Rotor Punching Sheet of Nuclear Reactor Cooling Medium Driving Motor

    Directory of Open Access Journals (Sweden)

    GE Bao-jun

    2017-02-01

    Full Text Available A strong stress is withstood by the rotor punching sheet during the running of nuclear reactor cooling medium driving motor. In order to study the strength on the rotor punching sheet and the influential factor of its stress,the rotor of driving motor was the research object, the three-dimensional rotor model of driving motor is established by the finite element method to obtain the Mires equivalent stress nephogram and check the rotor’s strength with setting parameters and constraints. According to different rotor speeds,the different average temperatures of rotor punching sheet and shaft and the different static magnitude of interference between rotor punching sheet and shaft,the research about how the contact pressure of matching surface between rotor punching sheet and shaft and the Mires equivalent stress are impacted is carried on. The results show that the maximum Miser equivalent stress value of rotor punching sheet emerges on the axial vents,the stress value is beyond the tensile limit of the materialand. The greater the static magnitude of interference and the smaller temperature difference of rotor punching sheet and shaft lead to the greater interface compressive stress of rotor punching sheet and shaft and the greater maximum Mires equivalent stress value of rotor punching sheet. The higher the rotor speed lead to the smaller interface compressive stress of rotor punching sheet and shaft and the greater equivalent stress value of rotor punching sheet.

  13. Operational Automatic Remote Sensing Image Understanding Systems: Beyond Geographic Object-Based and Object-Oriented Image Analysis (GEOBIA/GEOOIA. Part 2: Novel system Architecture, Information/Knowledge Representation, Algorithm Design and Implementation

    Directory of Open Access Journals (Sweden)

    Luigi Boschetti

    2012-09-01

    Full Text Available According to literature and despite their commercial success, state-of-the-art two-stage non-iterative geographic object-based image analysis (GEOBIA systems and three-stage iterative geographic object-oriented image analysis (GEOOIA systems, where GEOOIA/GEOBIA, remain affected by a lack of productivity, general consensus and research. To outperform the Quality Indexes of Operativeness (OQIs of existing GEOBIA/GEOOIA systems in compliance with the Quality Assurance Framework for Earth Observation (QA4EO guidelines, this methodological work is split into two parts. Based on an original multi-disciplinary Strengths, Weaknesses, Opportunities and Threats (SWOT analysis of the GEOBIA/GEOOIA approaches, the first part of this work promotes a shift of learning paradigm in the pre-attentive vision first stage of a remote sensing (RS image understanding system (RS-IUS, from sub-symbolic statistical model-based (inductive image segmentation to symbolic physical model-based (deductive image preliminary classification capable of accomplishing image sub-symbolic segmentation and image symbolic pre-classification simultaneously. In the present second part of this work, a novel hybrid (combined deductive and inductive RS-IUS architecture featuring a symbolic deductive pre-attentive vision first stage is proposed and discussed in terms of: (a computational theory (system design, (b information/knowledge representation, (c algorithm design and (d implementation. As proof-of-concept of symbolic physical model-based pre-attentive vision first stage, the spectral knowledge-based, operational, near real-time, multi-sensor, multi-resolution, application-independent Satellite Image Automatic Mapper™ (SIAM™ is selected from existing literature. To the best of these authors’ knowledge, this is the first time a symbolic syntactic inference system, like SIAM™, is made available to the RS community for operational use in a RS-IUS pre-attentive vision first stage

  14. State Fact Sheets on COPD

    Science.gov (United States)

    ... Submit Search The CDC Chronic Obstructive Pulmonary Disease (COPD) Note: Javascript is disabled or is not supported ... message, please visit this page: About CDC.gov . COPD Homepage Data and Statistics Fact Sheets Publications Publications ...

  15. A SURVEY OF AUTOMATION TECHNIQUES COMING FORTH IN SHEET-FED OFFSET PRINTING ORGANIZATIONS

    OpenAIRE

    Mr. Ramesh Kumar*, Mr. Bijender & Mr. Sandeep Boora

    2017-01-01

    Sheet-Fed offset is one of the premier processes in India as well as abroad. To cope up with customers large quantity demands automation has become mandatory. From prepress to post press a wide range of automation techniques exist and coming forth for sheet fed offset presses. Objective of this paper is to throw light on various sheet-fed offset automation techniques existing today and their futuristic implications. The data related to automation was collected with the help of survey conducte...

  16. Australian Government Balance Sheet Management

    OpenAIRE

    Wilson Au-Yeung; Jason McDonald; Amanda Sayegh

    2006-01-01

    Since almost eliminating net debt, the Australian Government%u2019s attention has turned to the financing of broader balance sheet liabilities, such as public sector superannuation. Australia will be developing a significant financial asset portfolio in the %u2018Future Fund%u2019 to smooth the financing of expenses through time. This raises the significant policy question of how best to manage the government balance sheet to reduce risk. This paper provides a framework for optimal balance sh...

  17. 1970-1997 energy balance-sheets

    International Nuclear Information System (INIS)

    1998-01-01

    The aim of this document is to bring together a consistent and harmonized set of statistical data on energy economics in the French territory. The information is based on the global and structural approach of the different energy balance-sheets published between 1970 and 1997. The first chapter gives a general idea of the energy situation of the passed year and outlines the evolution of the main aggregates (production, primary and final consumption etc..) comparatively to those of the general economy. The second chapter is devoted to the history of energy economics. Time series of indicators and diagrams allow to precise the structural modifications that occurred during the last decades. The main transformations in the national energy production and the development of the different energy sources in the industry, the residential and tertiary sectors and in the transportation sector are described too. The third chapter gives numerical data on energy for the last 28 years using the common Mtpe unit (million of tons of petroleum equivalent). These balance sheets are based on new energy keeping methods and use identical equivalence coefficients. The last chapter presents the energy balance sheets for the last three years, using the proper units for coal, petroleum, gas and electricity. (J.S.)

  18. An Adaptive Test Sheet Generation Mechanism Using Genetic Algorithm

    Directory of Open Access Journals (Sweden)

    Huan-Yu Lin

    2012-01-01

    Full Text Available For test-sheet composition systems, it is important to adaptively compose test sheets with diverse conceptual scopes, discrimination and difficulty degrees to meet various assessment requirements during real learning situations. Computation time and item exposure rate also influence performance and item bank security. Therefore, this study proposes an Adaptive Test Sheet Generation (ATSG mechanism, where a Candidate Item Selection Strategy adaptively determines candidate test items and conceptual granularities according to desired conceptual scopes, and an Aggregate Objective Function applies Genetic Algorithm (GA to figure out the approximate solution of mixed integer programming problem for the test-sheet composition. Experimental results show that the ATSG mechanism can efficiently, precisely generate test sheets to meet the various assessment requirements than existing ones. Furthermore, according to experimental finding, Fractal Time Series approach can be applied to analyze the self-similarity characteristics of GA’s fitness scores for improving the quality of the test-sheet composition in the near future.

  19. FDTD modeling of thin impedance sheets

    Science.gov (United States)

    Luebbers, Raymond J.; Kunz, Karl S.

    1991-01-01

    Thin sheets of resistive or dielectric material are commonly encountered in radar cross section calculations. Analysis of such sheets is simplified by using sheet impedances. In this paper it is shown that sheet impedances can be modeled easily and accurately using Finite Difference Time Domain (FDTD) methods.

  20. Ice_Sheets_CCI: Essential Climate Variables for the Greenland Ice Sheet

    Science.gov (United States)

    Forsberg, R.; Sørensen, L. S.; Khan, A.; Aas, C.; Evansberget, D.; Adalsteinsdottir, G.; Mottram, R.; Andersen, S. B.; Ahlstrøm, A.; Dall, J.; Kusk, A.; Merryman, J.; Hvidberg, C.; Khvorostovsky, K.; Nagler, T.; Rott, H.; Scharrer, M.; Shepard, A.; Ticconi, F.; Engdahl, M.

    2012-04-01

    As part of the ESA Climate Change Initiative (www.esa-cci.org) a long-term project "ice_sheets_cci" started January 1, 2012, in addition to the existing 11 projects already generating Essential Climate Variables (ECV) for the Global Climate Observing System (GCOS). The "ice_sheets_cci" goal is to generate a consistent, long-term and timely set of key climate parameters for the Greenland ice sheet, to maximize the impact of European satellite data on climate research, from missions such as ERS, Envisat and the future Sentinel satellites. The climate parameters to be provided, at first in a research context, and in the longer perspective by a routine production system, would be grids of Greenland ice sheet elevation changes from radar altimetry, ice velocity from repeat-pass SAR data, as well as time series of marine-terminating glacier calving front locations and grounding lines for floating-front glaciers. The ice_sheets_cci project will involve a broad interaction of the relevant cryosphere and climate communities, first through user consultations and specifications, and later in 2012 optional participation in "best" algorithm selection activities, where prototype climate parameter variables for selected regions and time frames will be produced and validated using an objective set of criteria ("Round-Robin intercomparison"). This comparative algorithm selection activity will be completely open, and we invite all interested scientific groups with relevant experience to participate. The results of the "Round Robin" exercise will form the algorithmic basis for the future ECV production system. First prototype results will be generated and validated by early 2014. The poster will show the planned outline of the project and some early prototype results.

  1. Point-of-purchase health information encourages customers to purchase vegetables: objective analysis by using a point-of-sales system.

    Science.gov (United States)

    Ogawa, Yoshiko; Tanabe, Naohito; Honda, Akiko; Azuma, Tomoko; Seki, Nao; Suzuki, Tsubasa; Suzuki, Hiroshi

    2011-07-01

    Point-of-purchase (POP) information at food stores could help promote healthy dietary habits. However, it has been difficult to evaluate the effects of such intervention on customers' behavior. We objectively evaluated the usefulness of POP health information for vegetables in the modification of customers' purchasing behavior by using the database of a point-of-sales (POS) system. Two supermarket stores belonging to the same chain were assigned as the intervention store (store I) and control store (store C). POP health information for vegetables was presented in store I for 60 days. The percent increase in daily sales of vegetables over the sales on the same date of the previous year was compared between the stores by using the database of the POS system, adjusting for the change in monthly visitors from the previous year (adjusted ∆sales). The adjusted ∆sales significantly increased during the intervention period (Spearman's ρ = 0.258, P for trend = 0.006) at store I but did not increase at store C (ρ = -0.037, P for trend = 0.728). The growth of the mean adjusted ∆sales of total vegetables from 30 days before the intervention period through the latter half of the intervention period was estimated to be greater at store I than at store C by 18.7 percentage points (95% confidence interval 1.6-35.9). Health-related POP information for vegetables in supermarkets can encourage customers to purchase and, probably, consume vegetables.

  2. Nuclar Data Sheets for A = 83

    International Nuclear Information System (INIS)

    Kocher, D.C.

    1975-01-01

    The 1966 version of Nuclear Data Sheets for A = 83 was revised on the basis of experimental data received prior to November 1, 1974. Information from approximately 90 papers and communications was included in the present evaluation. Data on nine A = 83 nuclei are presented. This A-chain is characterized by a paucity of reaction data compared with radioactive decay data. For 83 Ge only the half-life is known. For 83 As, the half-life is known but few details of the decay scheme have been determined. The decay schemes of the 83 Se ground state and first-excited state are reasonably well established, and levels in 83 Se are known from (d,p). The decay schemes of 83 Br and 83 Rb are well established, and these decays give all adopted information on levels in stable 83 Kr. The complex decay scheme for 83 Sr is reasonably well established, which leads to all information on levels in 83 Rb. Information on 83 Sr levels is obtained from 83 Y decays and (d,t). The decay schemes for two 83 Y isomers have been reasonably well determined, but the ordering of the isomers is not known. The compilers regard the identification of 83 Zr as uncertain. This compilation is divided into three parts appearing in the following order: Drawings, Sheets, References. (U.S.)

  3. Optimizing multiple sequence alignments using a genetic algorithm based on three objectives: structural information, non-gaps percentage and totally conserved columns.

    Science.gov (United States)

    Ortuño, Francisco M; Valenzuela, Olga; Rojas, Fernando; Pomares, Hector; Florido, Javier P; Urquiza, Jose M; Rojas, Ignacio

    2013-09-01

    Multiple sequence alignments (MSAs) are widely used approaches in bioinformatics to carry out other tasks such as structure predictions, biological function analyses or phylogenetic modeling. However, current tools usually provide partially optimal alignments, as each one is focused on specific biological features. Thus, the same set of sequences can produce different alignments, above all when sequences are less similar. Consequently, researchers and biologists do not agree about which is the most suitable way to evaluate MSAs. Recent evaluations tend to use more complex scores including further biological features. Among them, 3D structures are increasingly being used to evaluate alignments. Because structures are more conserved in proteins than sequences, scores with structural information are better suited to evaluate more distant relationships between sequences. The proposed multiobjective algorithm, based on the non-dominated sorting genetic algorithm, aims to jointly optimize three objectives: STRIKE score, non-gaps percentage and totally conserved columns. It was significantly assessed on the BAliBASE benchmark according to the Kruskal-Wallis test (P algorithm also outperforms other aligners, such as ClustalW, Multiple Sequence Alignment Genetic Algorithm (MSA-GA), PRRP, DIALIGN, Hidden Markov Model Training (HMMT), Pattern-Induced Multi-sequence Alignment (PIMA), MULTIALIGN, Sequence Alignment Genetic Algorithm (SAGA), PILEUP, Rubber Band Technique Genetic Algorithm (RBT-GA) and Vertical Decomposition Genetic Algorithm (VDGA), according to the Wilcoxon signed-rank test (P 0.05) with the advantage of being able to use less structures. Structural information is included within the objective function to evaluate more accurately the obtained alignments. The source code is available at http://www.ugr.es/~fortuno/MOSAStrE/MO-SAStrE.zip.

  4. Penguin Fact Sheet.

    Science.gov (United States)

    Flotsam and Jetsam: A Newsletter for Massachusetts Marine Educators, 1985

    1985-01-01

    Presents factual information on penguins using an outline format. Includes descriptions of physical characteristics, behavioral mechanisms, geographical distribution, and physiological processes. Provides separate bibliographies for teachers and students. (ML)

  5. On Jovian plasma sheet structure

    International Nuclear Information System (INIS)

    Khurana, K.K.; Kivelson, M.G.

    1989-01-01

    The authors evaluate several models of Jovian plasma sheet structure by determining how well they organize several aspects of the observed Voyager 2 magnetic field characteristics as a function of Jovicentric radial distance. It is shown that in the local time sector of the Voyager 2 outbound pass (near 0300 LT) the published hinged-magnetodisc models with wave (i.e., models corrected for finite wave velocity effects) are more successful than the published magnetic anomaly model in predicting locations of current sheet crossings. They also consider the boundary between the plasma sheet and the magnetotail lobe which is expected to vary slowly with radial distance. They use this boundary location as a further test of the models of the magnetotail. They show that the compressional MHD waves have much smaller amplitude in the lobes than in the plasma sheet and use this criterion to refine the identification of the plasma-sheet-lobe boundary. When the locations of crossings into and out of the lobes are examined, it becomes evident that the magnetic-anomaly model yields a flaring plasma sheet with a halfwidth of ∼ 3 R J at a radial distance of 20 R J and ∼ 12 R J at a radial distance of 100 R J . The hinged-magnetodisc models with wave, on the other hand, predict a halfwidth of ∼ 3.5 R J independent of distance beyond 20 R J . New optimized versions of the two models locate both the current sheet crossings and lobe encounters equally successfully. The optimized hinged-magnetodisc model suggests that the wave velocity decreases with increasing radial distance. The optimized magnetic anomaly model yields lower velocity contrast than the model of Vasyliunas and Dessler (1981)

  6. Automobile sheet metal part production with incremental sheet forming

    Directory of Open Access Journals (Sweden)

    İsmail DURGUN

    2016-02-01

    Full Text Available Nowadays, effect of global warming is increasing drastically so it leads to increased interest on energy efficiency and sustainable production methods. As a result of adverse conditions, national and international project platforms, OEMs (Original Equipment Manufacturers, SMEs (Small and Mid-size Manufacturers perform many studies or improve existing methodologies in scope of advanced manufacturing techniques. In this study, advanced manufacturing and sustainable production method "Incremental Sheet Metal Forming (ISF" was used for sheet metal forming process. A vehicle fender was manufactured with or without die by using different toolpath strategies and die sets. At the end of the study, Results have been investigated under the influence of method and parameters used.Keywords: Template incremental sheet metal, Metal forming

  7. Low cost light-sheet microscopy for whole brain imaging

    Science.gov (United States)

    Kumar, Manish; Nasenbeny, Jordan; Kozorovitskiy, Yevgenia

    2018-02-01

    Light-sheet microscopy has evolved as an indispensable tool in imaging biological samples. It can image 3D samples at fast speed, with high-resolution optical sectioning, and with reduced photobleaching effects. These properties make light-sheet microscopy ideal for imaging fluorophores in a variety of biological samples and organisms, e.g. zebrafish, drosophila, cleared mouse brains, etc. While most commercial turnkey light-sheet systems are expensive, the existing lower cost implementations, e.g. OpenSPIM, are focused on achieving high-resolution imaging of small samples or organisms like zebrafish. In this work, we substantially reduce the cost of light-sheet microscope system while targeting to image much larger samples, i.e. cleared mouse brains, at single-cell resolution. The expensive components of a lightsheet system - excitation laser, water-immersion objectives, and translation stage - are replaced with an incoherent laser diode, dry objectives, and a custom-built Arduino-controlled translation stage. A low-cost CUBIC protocol is used to clear fixed mouse brain samples. The open-source platforms of μManager and Fiji support image acquisition, processing, and visualization. Our system can easily be extended to multi-color light-sheet microscopy.

  8. Magneto-hydrodynamics of coupled fluid–sheet interface with mass suction and blowing

    International Nuclear Information System (INIS)

    Ahmad, R.

    2016-01-01

    There are large number of studies which prescribe the kinematics of the sheet and ignore the sheet's mechanics. However, the current boundary layer analysis investigates the mechanics of both the electrically conducting fluid and a permeable sheet, which makes it distinct from the other studies in the literature. One of the objectives of the current study is to (i) examine the behaviour of magnetic field effect for both the surface and the electrically conducting fluid (ii) investigate the heat and mass transfer between a permeable sheet and the surrounding electrically conducting fluid across the hydro, thermal and mass boundary layers. Self-similar solutions are obtained by considering the RK45 technique. Analytical solution is also found for the stretching sheet case. The skin friction dual solutions are presented for various types of sheet. The influence of pertinent parameters on the dimensionless velocity, shear stress, temperature, mass concentration, heat and mass transfer rates on the fluid–sheet interface is presented graphically as well as numerically. The obtained results are of potential benefit for studying the electrically conducting flow over various soft surfaces such as synthetic plastics, soft silicone sheet and soft synthetic rubber sheet. These surfaces are easily deformed by thermal fluctuations or thermal stresses. - Highlights: • The momentum equation is modelled for both the surrounding MHD fluid and the sheet with the effects of mass suction and blowing. • The current study further investigates the heat and mass transfer characteristics between a permeable sheet and the surrounding electrically conducting fluid across the thermal and mass boundary layers. • Both the approximated and analytical techniques have been included for the purpose of comparison, and the perfect numerical agreements have been established with the previous studies. • Dual solutions for the skin friction coefficients are found for various categories of

  9. Uranium mining sites - Thematic sheets

    International Nuclear Information System (INIS)

    2009-01-01

    A first sheet proposes comments, data and key numbers about uranium extraction in France: general overview of uranium mining sites, status of waste rock and tailings after exploitation, site rehabilitation. The second sheet addresses the sources of exposure to ionizing radiations due to ancient uranium mining sites: discussion on the identification of these sources associated with these sites, properly due to mining activities or to tailings, or due to the transfer of radioactive substances towards water and to the contamination of sediments, description of the practice and assessment of radiological control of mining sites. A third sheet addresses the radiological exposure of public to waste rocks, and the dose assessment according to exposure scenarios: main exposure ways to be considered, studied exposure scenarios (passage on backfilled path and grounds, stay in buildings built on waste rocks, keeping mineralogical samples at home). The fourth sheet addresses research programmes of the IRSN on uranium and radon: epidemiological studies (performed on mine workers; on French and on European cohorts, French and European studies on the risk of lung cancer associated with radon in housing), study of the biological effects of chronic exposures. The last sheet addresses studies and expertises performed by the IRSN on ancient uranium mining sites in France: studies commissioned by public authorities, radioactivity control studies performed by the IRSN about mining sites, participation of the IRSN to actions to promote openness to civil society

  10. Final Rule to Reduce Hazardous Air Emissions from Newly Built Stationary Combustion Turbines: Fact Sheet

    Science.gov (United States)

    This page contains an August 2003 fact sheet with information regarding the National Emissions Standards for Hazardous Air Pollutants (NESHAP) for Stationary Combustion Turbines. This document provides a summary of the information for this NESHAP.

  11. Effects of flow sheet implementation on physician performance in the management of asthmatic patients.

    Science.gov (United States)

    Ruoff, Gary

    2002-01-01

    This project focused on increasing compliance, in a large family practice group, with quality indicators for the management of asthma. The objective was to determine if use of a flow sheet incorporating the Global Initiative for Asthma (GINA) guidelines could improve compliance with those guidelines if the flow sheet was placed in patients' medical records. After review and selection of 14 clinical quality indicators, physicians in the practice implemented a flow sheet as an intervention. These flow sheets were inserted into the records of 122 randomly selected patients with asthma. Medical records were reviewed before the flow sheets were placed in the records, and again approximately 6 months later, to determine if there was a change in compliance with the quality indicators. Improvement of documentation was demonstrated in 13 of the 14 quality indicators. The results indicate that compliance with asthma management quality indicators can improve with the use of a flow sheet.

  12. Respirator Fact Sheet

    Science.gov (United States)

    ... 6, 2014 Content source: National Institute for Occupational Safety and Health Education and Information Division Email Recommend Tweet YouTube Instagram Listen Watch RSS ABOUT About CDC Jobs Funding LEGAL Policies Privacy FOIA No Fear Act OIG 1600 Clifton Road Atlanta , GA 30329-4027 USA 800-CDC-INFO ( ...

  13. Elegant objects

    CERN Document Server

    Bugayenko, Yegor

    2017-01-01

    There are 23 practical recommendations for object-oriented programmers. Most of them are completely against everything you've read in other books. For example, static methods, NULL references, getters, setters, and mutable classes are called evil. Compound variable names, validators, private static literals, configurable objects, inheritance, annotations, MVC, dependency injection containers, reflection, ORM and even algorithms are our enemies.

  14. Objective lens

    Science.gov (United States)

    Olczak, Eugene G. (Inventor)

    2011-01-01

    An objective lens and a method for using same. The objective lens has a first end, a second end, and a plurality of optical elements. The optical elements are positioned between the first end and the second end and are at least substantially symmetric about a plane centered between the first end and the second end.

  15. Root-growth-inhibiting sheet

    Science.gov (United States)

    Burton, F.G.; Cataldo, D.A.; Cline, J.F.; Skiens, W.E.; Van Voris, P.

    1993-01-26

    In accordance with this invention, a porous sheet material is provided at intervals with bodies of a polymer which contain a 2,6-dinitroaniline. The sheet material is made porous to permit free passage of water. It may be either a perforated sheet or a woven or non-woven textile material. A particularly desirable embodiment is a non-woven fabric of non-biodegradable material. This type of material is known as a geotextile'' and is used for weed control, prevention of erosion on slopes, and other landscaping purposes. In order to obtain a root repelling property, a dinitroaniline is blended with a polymer which is attached to the geotextile or other porous material.

  16. Optimal swimming of a sheet.

    Science.gov (United States)

    Montenegro-Johnson, Thomas D; Lauga, Eric

    2014-06-01

    Propulsion at microscopic scales is often achieved through propagating traveling waves along hairlike organelles called flagella. Taylor's two-dimensional swimming sheet model is frequently used to provide insight into problems of flagellar propulsion. We derive numerically the large-amplitude wave form of the two-dimensional swimming sheet that yields optimum hydrodynamic efficiency: the ratio of the squared swimming speed to the rate-of-working of the sheet against the fluid. Using the boundary element method, we show that the optimal wave form is a front-back symmetric regularized cusp that is 25% more efficient than the optimal sine wave. This optimal two-dimensional shape is smooth, qualitatively different from the kinked form of Lighthill's optimal three-dimensional flagellum, not predicted by small-amplitude theory, and different from the smooth circular-arc-like shape of active elastic filaments.

  17. Root-growth-inhibiting sheet

    Science.gov (United States)

    Burton, Frederick G.; Cataldo, Dominic A.; Cline, John F.; Skiens, W. Eugene; Van Voris, Peter

    1993-01-01

    In accordance with this invention, a porous sheet material is provided at intervals with bodies of a polymer which contain a 2,6-dinitroaniline. The sheet material is made porous to permit free passage of water. It may be either a perforated sheet or a woven or non-woven textile material. A particularly desirable embodiment is a non-woven fabric of non-biodegradable material. This type of material is known as a "geotextile" and is used for weed control, prevention of erosion on slopes, and other landscaping purposes. In order to obtain a root repelling property, a dinitroaniline is blended with a polymer which is attached to the geotextile or other porous material.

  18. Strengthening Interprofessional Requirements Engineering Through Action Sheets: A Pilot Study.

    Science.gov (United States)

    Kunz, Aline; Pohlmann, Sabrina; Heinze, Oliver; Brandner, Antje; Reiß, Christina; Kamradt, Martina; Szecsenyi, Joachim; Ose, Dominik

    2016-10-18

    The importance of information and communication technology for healthcare is steadily growing. Newly developed tools are addressing different user groups: physicians, other health care professionals, social workers, patients, and family members. Since often many different actors with different expertise and perspectives are involved in the development process it can be a challenge to integrate the user-reported requirements of those heterogeneous user groups. Nevertheless, the understanding and consideration of user requirements is the prerequisite of building a feasible technical solution. In the course of the presented project it proved to be difficult to gain clear action steps and priorities for the development process out of the primary requirements compilation. Even if a regular exchange between involved teams took place there was a lack of a common language. The objective of this paper is to show how the already existing requirements catalog was subdivided into specific, prioritized, and coherent working packages and the cooperation of multiple interprofessional teams within one development project was reorganized at the same time. In the case presented, the manner of cooperation was reorganized and a new instrument called an Action Sheet was implemented. This paper introduces the newly developed methodology which was meant to smooth the development of a user-centered software product and to restructure interprofessional cooperation. There were 10 focus groups in which views of patients with colorectal cancer, physicians, and other health care professionals were collected in order to create a requirements catalog for developing a personal electronic health record. Data were audio- and videotaped, transcribed verbatim, and thematically analyzed. Afterwards, the requirements catalog was reorganized in the form of Action Sheets which supported the interprofessional cooperation referring to the development process of a personal electronic health record for the

  19. Ice sheet hydrology - a review

    Energy Technology Data Exchange (ETDEWEB)

    Jansson, Peter; Naeslund, Jens-Ove [Dept. of Physical Geography and Quaternary Geology, Stockholm Univ., Stockholm (Sweden); Rodhe, Lars [Geological Survey of Sweden, Uppsala (Sweden)

    2007-03-15

    This report summarizes the theoretical knowledge on water flow in and beneath glaciers and ice sheets and how these theories are applied in models to simulate the hydrology of ice sheets. The purpose is to present the state of knowledge and, perhaps more importantly, identify the gaps in our understanding of ice sheet hydrology. Many general concepts in hydrology and hydraulics are applicable to water flow in glaciers. However, the unique situation of having the liquid phase flowing in conduits of the solid phase of the same material, water, is not a commonly occurring phenomena. This situation means that the heat exchange between the phases and the resulting phase changes also have to be accounted for in the analysis. The fact that the solidus in the pressure-temperature dependent phase diagram of water has a negative slope provides further complications. Ice can thus melt or freeze from both temperature and pressure variations or variations in both. In order to provide details of the current understanding of water flow in conjunction with deforming ice and to provide understanding for the development of ideas and models, emphasis has been put on the mathematical treatments, which are reproduced in detail. Qualitative results corroborating theory or, perhaps more often, questioning the simplifications made in theory, are also given. The overarching problem with our knowledge of glacier hydrology is the gap between the local theories of processes and the general flow of water in glaciers and ice sheets. Water is often channelized in non-stationary conduits through the ice, features which due to their minute size relative to the size of glaciers and ice sheets are difficult to incorporate in spatially larger models. Since the dynamic response of ice sheets to global warming is becoming a key issue in, e.g. sea-level change studies, the problems of the coupling between the hydrology of an ice sheet and its dynamics is steadily gaining interest. New work is emerging

  20. Modelling the Antarctic Ice Sheet

    DEFF Research Database (Denmark)

    Pedersen, Jens Olaf Pepke; Holm, A.

    2015-01-01

    to sea level high stands during past interglacial periods. A number of AIS models have been developed and applied to try to understand the workings of the AIS and to form a robust basis for future projections of the AIS contribution to sea level change. The recent DCESS (Danish Center for Earth System......The Antarctic ice sheet is a major player in the Earth’s climate system and is by far the largest depository of fresh water on the planet. Ice stored in the Antarctic ice sheet (AIS) contains enough water to raise sea level by about 58 m, and ice loss from Antarctica contributed significantly...

  1. Ice sheet hydrology - a review

    International Nuclear Information System (INIS)

    Jansson, Peter; Naeslund, Jens-Ove; Rodhe, Lars

    2007-03-01

    This report summarizes the theoretical knowledge on water flow in and beneath glaciers and ice sheets and how these theories are applied in models to simulate the hydrology of ice sheets. The purpose is to present the state of knowledge and, perhaps more importantly, identify the gaps in our understanding of ice sheet hydrology. Many general concepts in hydrology and hydraulics are applicable to water flow in glaciers. However, the unique situation of having the liquid phase flowing in conduits of the solid phase of the same material, water, is not a commonly occurring phenomena. This situation means that the heat exchange between the phases and the resulting phase changes also have to be accounted for in the analysis. The fact that the solidus in the pressure-temperature dependent phase diagram of water has a negative slope provides further complications. Ice can thus melt or freeze from both temperature and pressure variations or variations in both. In order to provide details of the current understanding of water flow in conjunction with deforming ice and to provide understanding for the development of ideas and models, emphasis has been put on the mathematical treatments, which are reproduced in detail. Qualitative results corroborating theory or, perhaps more often, questioning the simplifications made in theory, are also given. The overarching problem with our knowledge of glacier hydrology is the gap between the local theories of processes and the general flow of water in glaciers and ice sheets. Water is often channelized in non-stationary conduits through the ice, features which due to their minute size relative to the size of glaciers and ice sheets are difficult to incorporate in spatially larger models. Since the dynamic response of ice sheets to global warming is becoming a key issue in, e.g. sea-level change studies, the problems of the coupling between the hydrology of an ice sheet and its dynamics is steadily gaining interest. New work is emerging

  2. Sheet Beam Klystron Instability Analysis

    International Nuclear Information System (INIS)

    Bane, K.

    2009-01-01

    Using the principle of energy balance we develop a 2D theory for calculating growth rates of instability in a two-cavity model of a sheet beam klystron. An important ingredient is a TE-like mode in the gap that also gives a longitudinal kick to the beam. When compared with a self-consistent particle-in-cell calculation, with sheet beam klystron-type parameters, agreement is quite good up to half the design current, 65 A; at full current, however, other, current-dependent effects come in and the results deviate significantly

  3. The social balance sheet 2004

    OpenAIRE

    Ph. Delhez; P. Heuse

    2005-01-01

    Each year, in the 4th quarter’s Economic Review, the National Bank examines the provisional results of the social balance sheets. As all the social balance sheets are not yet available for 2004, the study is based on a limited population of enterprises, compiled according to the principle of a constant sample. This population is made up of 38,530 enterprises employing around 1,331,000 workers in 2004. The main results of the analysis, in terms of employment, working hours, labour cost and tra...

  4. Well data summary sheets. Vol. 33: North sea wells

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    This 33rd volume of the `Well Data Summary sheets` includes data from seven recently released offshore wells from the North Sea. The wells Baron-2, S.E. Adda-1 and Skjold Flank-1 were presented in our `Well Data Summary Sheets, special volume`, published May 1, 1997. In volume 33, the wells Baron-2 and Skjold Flank-1 are updated with respect to information on sidewall cores. Information regarding all released well data, included in our well data summary sheets, are available on GEUS homepage: http://www.geus.dk/ or the departments homepage: http://www.geus.dk/departments/geol-info-data-centre/geoldata.htm/. A complete index of releases wells in volumes 17-33 is included. (au)

  5. Best, Useful and Objective Precisions for Information Retrieval of Three Search Methods in PubMed and iPubMed

    Directory of Open Access Journals (Sweden)

    Somayyeh Nadi Ravandi

    2016-10-01

    Full Text Available MEDLINE is one of the valuable sources of medical information on the Internet. Among the different open access sites of MEDLINE, PubMed is the best-known site. In 2010, iPubMed was established with an interaction-fuzzy search method for MEDLINE access. In the present work, we aimed to compare the precision of the retrieved sources (Best, Useful and Objective precision in the PubMed and iPubMed using two search methods (simple and MeSH search in PubMed and interaction-fuzzy method in iPubmed. During our semi-empirical study period, we held training workshops for 61 students of higher education to teach them Simple Search, MeSH Search, and Fuzzy-Interaction Search methods. Then, the precision of 305 searches for each method prepared by the students was calculated on the basis of Best precision, Useful precision, and Objective precision formulas. Analyses were done in SPSS version 11.5 using the Friedman and Wilcoxon Test, and three precisions obtained with the three precision formulas were studied for the three search methods. The mean precision of the interaction-fuzzy Search method was higher than that of the simple search and MeSH search for all three types of precision, i.e., Best precision, Useful precision, and Objective precision, and the Simple search method was in the next rank, and their mean precisions were significantly different (P < 0.001. The precision of the interaction-fuzzy search method in iPubmed was investigated for the first time. Also for the first time, three types of precision were evaluated in PubMed and iPubmed. The results showed that the Interaction-Fuzzy search method is more precise than using the natural language search (simple search and MeSH search, and users of this method found papers that were more related to their queries; even though search in Pubmed is useful, it is important that users apply new search methods to obtain the best results.

  6. Deformation Analysis of RC Ties Externally Strengthened with FRP Sheets

    Science.gov (United States)

    Gribniak, V.; Arnautov, A. K.; Kaklauskas, G.; Jakstaite, R.; Tamulenas, V.; Gudonis, E.

    2014-11-01

    The current study has two objectives: to validate the ability of the Atena finite-element software to estimate the deformations of reinforced concrete (RC) elements strengthened with fiber-reinforced polymer (FRP) sheets and to assess the effect of FRP-to-concrete bond strength on the results of numerical simulation. It is shown that the bond strength has to be selected according to the overall stiffness of the composite element. The numerical results found are corroborated experimentally by tensile tests of RC elements strengthened with basalt FRP sheets.

  7. Information technology and innovative drainage management practices for selenium load reduction from irrigated agriculture to provide stakeholder assurances and meet contaminant mass loading policy objectives

    Energy Technology Data Exchange (ETDEWEB)

    Quinn, N.W.T.

    2009-10-15

    Many perceive the implementation of environmental regulatory policy, especially concerning non-point source pollution from irrigated agriculture, as being less efficient in the United States than in many other countries. This is partly a result of the stakeholder involvement process but is also a reflection of the inability to make effective use of Environmental Decision Support Systems (EDSS) to facilitate technical information exchange with stakeholders and to provide a forum for innovative ideas for controlling non-point source pollutant loading. This paper describes one of the success stories where a standardized Environmental Protection Agency (EPA) methodology was modified to better suit regulation of a trace element in agricultural subsurface drainage and information technology was developed to help guide stakeholders, provide assurances to the public and encourage innovation while improving compliance with State water quality objectives. The geographic focus of the paper is the western San Joaquin Valley where, in 1985, evapoconcentration of selenium in agricultural subsurface drainage water, diverted into large ponds within a federal wildlife refuge, caused teratogenecity in waterfowl embryos and in other sensitive wildlife species. The fallout from this environmental disaster was a concerted attempt by State and Federal water agencies to regulate non-point source loads of the trace element selenium. The complexity of selenium hydrogeochemistry, the difficulty and expense of selenium concentration monitoring and political discord between agricultural and environmental interests created challenges to the regulation process. Innovative policy and institutional constructs, supported by environmental monitoring and the web-based data management and dissemination systems, provided essential decision support, created opportunities for adaptive management and ultimately contributed to project success. The paper provides a retrospective on the contentious planning

  8. Final Rule to Reduce Toxic Air Emissions from Asphalt Processing and Asphalt Roofing Manufacturing Facilities Fact Sheet

    Science.gov (United States)

    This page contains a February 2003 fact sheet with information regarding the National Emissions Standards for Hazardous Air Pollutants (NESHAP) for Asphalt Processing and Asphalt Roofing Manufacturing.

  9. Orientation determination of interfacial beta-sheet structures in situ.

    Science.gov (United States)

    Nguyen, Khoi Tan; King, John Thomas; Chen, Zhan

    2010-07-01

    Structural information such as orientations of interfacial proteins and peptides is important for understanding properties and functions of such biological molecules, which play crucial roles in biological applications and processes such as antimicrobial selectivity, membrane protein activity, biocompatibility, and biosensing performance. The alpha-helical and beta-sheet structures are the most widely encountered secondary structures in peptides and proteins. In this paper, for the first time, a method to quantify the orientation of the interfacial beta-sheet structure using a combined attenuated total reflectance Fourier transformation infrared spectroscopic (ATR-FTIR) and sum frequency generation (SFG) vibrational spectroscopic study was developed. As an illustration of the methodology, the orientation of tachyplesin I, a 17 amino acid peptide with an antiparallel beta-sheet, adsorbed to polymer surfaces as well as associated with a lipid bilayer was determined using the regular and chiral SFG spectra, together with polarized ATR-FTIR amide I signals. Both the tilt angle (theta) and the twist angle (psi) of the beta-sheet at interfaces are determined. The developed method in this paper can be used to obtain in situ structural information of beta-sheet components in complex molecules. The combination of this method and the existing methodology that is currently used to investigate alpha-helical structures will greatly broaden the application of optical spectroscopy in physical chemistry, biochemistry, biophysics, and structural biology.

  10. Forming properties and springback evaluation of copper beryllium sheets

    International Nuclear Information System (INIS)

    Tseng, A.A.; Jen, K.P.; Chen, T.C.; Kondetimmamhalli, R.

    1995-01-01

    Copper beryllium (CuBe) alloys possess excellent strength and conductivity. They have become the most important materials used for producing high reliability connectors and interconnections for electrical and electronic applications. As demand for high connection density in electrical and electronic products grows, springback behaviors become increasingly critical in fabricating these miniaturized contact components from sheet base materials. In the present article, a study of the springback behavior of CuBe sheets under different heat treatments is presented, with the goal of providing reliable information needed for fabricating more intricate connection parts. Both experimental and analytical techniques were adopted. The tensile tester was first used to study the springback related tensile properties. The governing tensile parameters on springback were identified, and their variations for sheets with different heat treatments were studied. It was found that a bilinear constitutive relationship can be characterize the stress strain behavior of the CuBe alloy. A closed form solution based on this bilinear relationship was formulated to predict the springback for the CuBe sheets at bending conditions. A V-shaped bend tester having an interchangeable punch to accommodate multiple radii was designed and built to evaluate the springback properties of CuBe sheets. A good correlation was found between the analytical predictions and experimental data. A parametric study, as an example, was also performed to provide the springback information needed for designing complicated connectors

  11. Extended objects

    International Nuclear Information System (INIS)

    Creutz, M.

    1976-01-01

    After some disconnected comments on the MIT bag and string models for extended hadrons, I review current understanding of extended objects in classical conventional relativistic field theories and their quantum mechanical interpretation

  12. Trusted Objects

    International Nuclear Information System (INIS)

    CAMPBELL, PHILIP L.; PIERSON, LYNDON G.; WITZKE, EDWARD L.

    1999-01-01

    In the world of computers a trusted object is a collection of possibly-sensitive data and programs that can be allowed to reside and execute on a computer, even on an adversary's machine. Beyond the scope of one computer we believe that network-based agents in high-consequence and highly reliable applications will depend on this approach, and that the basis for such objects is what we call ''faithful execution.''

  13. Modeling the Fracture of Ice Sheets on Parallel Computers

    Energy Technology Data Exchange (ETDEWEB)

    Waisman, Haim [Columbia Univ., New York, NY (United States); Tuminaro, Ray [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2013-10-10

    The objective of this project was to investigate the complex fracture of ice and understand its role within larger ice sheet simulations and global climate change. This objective was achieved by developing novel physics based models for ice, novel numerical tools to enable the modeling of the physics and by collaboration with the ice community experts. At the present time, ice fracture is not explicitly considered within ice sheet models due in part to large computational costs associated with the accurate modeling of this complex phenomena. However, fracture not only plays an extremely important role in regional behavior but also influences ice dynamics over much larger zones in ways that are currently not well understood. To this end, our research findings through this project offers significant advancement to the field and closes a large gap of knowledge in understanding and modeling the fracture of ice sheets in the polar regions. Thus, we believe that our objective has been achieved and our research accomplishments are significant. This is corroborated through a set of published papers, posters and presentations at technical conferences in the field. In particular significant progress has been made in the mechanics of ice, fracture of ice sheets and ice shelves in polar regions and sophisticated numerical methods that enable the solution of the physics in an efficient way.

  14. Off-Balance Sheet Financing.

    Science.gov (United States)

    Adams, Matthew C.

    1998-01-01

    Examines off-balance sheet financing, the facilities use of outsourcing for selected needs, as a means of saving operational costs and using facility assets efficiently. Examples of using outside sources for energy supply and food services, as well as partnering with business for facility expansion are provided. Concluding comments address tax…

  15. Evaluation of essential work of fracture in a dual phase high strength steel sheet

    International Nuclear Information System (INIS)

    Gutierrez, D.; Perez, L. I.; Lara, A.; Casellas, D.; Prado, J. M.

    2013-01-01

    Fracture toughness of advanced high strength steels (AHSS), can be used to optimize crash behavior of structural components. However it cannot be readily measured in metal sheet because of the sheet thickness. In this work, the Essential Work of Fracture (EWF) methodology is proposed to evaluate the fracture toughness of metal sheets. It has been successfully applied in polymers films and some metal sheets. However, their information about the applicability of this methodology to AHSS is relatively scarce. In the present work the fracture toughness of a Dual Phase (strength of 800 MPa) and drawing steel sheets has been measured by means of the EWF. The results show that the test requirements are met and also show the clear influence of notch radii on the measured values, specially for the AHSS grade. Thus, the EWF is postulated as a methodology to evaluate the fracture toughness in AHSS sheets. (Author) 18 refs.

  16. Scanning light-sheet microscopy in the whole mouse brain with HiLo background rejection

    Science.gov (United States)

    Mertz, Jerome; Kim, Jinhyun

    2010-01-01

    It is well known that light-sheet illumination can enable optically sectioned wide-field imaging of macroscopic samples. However, the optical sectioning capacity of a light-sheet macroscope is undermined by sample-induced scattering or aberrations that broaden the thickness of the sheet illumination. We present a technique to enhance the optical sectioning capacity of a scanning light-sheet microscope by out-of-focus background rejection. The technique, called HiLo microscopy, makes use of two images sequentially acquired with uniform and structured sheet illumination. An optically sectioned image is then synthesized by fusing high and low spatial frequency information from both images. The benefits of combining light-sheet macroscopy and HiLo background rejection are demonstrated in optically cleared whole mouse brain samples, using both green fluorescent protein (GFP)-fluorescence and dark-field scattered light contrast.

  17. 76 FR 48122 - Polyethylene Terephthalate Film, Sheet, and Strip From Brazil: Preliminary Results of Antidumping...

    Science.gov (United States)

    2011-08-08

    ... on polyethylene terephthalate film, sheet, and strip (PET film) from Brazil. This administrative..., 2011. FOR FURTHER INFORMATION CONTACT: Deborah Scott or Robert James, AD/CVD Operations, Office 7... antidumping duty order on PET film from Brazil. See Polyethylene Terephthalate Film, Sheet, and Strip From...

  18. 78 FR 47276 - Polyethylene Terephthalate (PET) Film, Sheet, and Strip From India: Final Results of the...

    Science.gov (United States)

    2013-08-05

    ... (PET) Film, Sheet, and Strip From India: Final Results of the Expedited Second Sunset Review of the... terephthalate (PET) film, sheet, and strip (``PET film'') from India. The Department finds that revocation of... INFORMATION CONTACT: Sean Carey or Dana Mermelstein, AD/CVD Operations, Office 6, Import Administration...

  19. OPA Q's and A's: Overview of the Oil Pollution Act of 1990. Fact sheet

    International Nuclear Information System (INIS)

    1991-12-01

    The OPA Q's and A's are part of a series of fact sheets that provide up-to-date information on EPA's implementation of the OPA. The first fact sheet provides an overview of the various provisions of the OPA and the Agency's responsibilities under the new law

  20. Predicted wear on the tube outside surface due to foreign object in the secondary side of steam generator

    International Nuclear Information System (INIS)

    Kim, Hyung Nam; Cho, Nam Cheoul

    2012-01-01

    It is necessary to evaluate the effects of foreign objects on steam generator tubes and to use this information to take appropriate safety precautions to prevent nuclear accidents. Foreign objects may include loose parts from the feed water system and items lost by workers during o/h, and may flow into the secondary side of steam generators during operation. A foreign object could damage steam generator tube walls if there is relative motion between the tube and the foreign object. This is especially true for foreign objects that land on the tube sheet because the velocity of cross flow, which creates a contact force between the tube and foreign object, is relatively high there. During steam generator overhauls, foreign objects are detected by non destructive methods such as the visual test and/or the eddy current test. Confirmed foreign objects should be removed for nuclear safety. The Foreign Object Search and Retrieval System (FOSAR) can be used to remove foreign objects from the steam generators with a square tube array. However, the FOSAR cannot be used (or can be used in only a very restricted area, such as the outside of the tube bundle) in the steam generators with a triangular tube array. In order to continue nuclear power plant operations without removing foreign objects, the integrity of the steam generator tube must be verified. This paper introduces a practical method developed to evaluate the effects of foreign objects detected on tube sheets in the secondary sides of steam generators

  1. Flexible shielding material sheet for radiations

    International Nuclear Information System (INIS)

    Kokan, Susumu; Fukuoka, Masasuke.

    1976-01-01

    Object: To provide a soft sheet of shielding material for radioactive rays without involving no problem such as environmental contamination, without generating intense second radioactive rays such as conventional cadmium. Structure: 100 weight parts of boron compound (boron carbide, boric acid anhydride) and 5 to 60 weight parts of low molecular-weight polyethylene resin, of which average molecular weight is less than 8000, are agitated in a mixer and during agitation are increased in temperature to a level above a softening temperature of the polyethylene resin to obtain a mixture in which the boron compound is coated with the low molecular-weight polyethylene. Next, 3 to 200 weight parts of the resultant mixture and 100 weight parts of olefin group resin (ethylene-vinyl acetate copolymer, styrene-butadiene random copolymer) are evenly mixed within an agitator such as a tumbler to form a sheet having the desired thickness and dimension. The thus obtained shielding material generates no capture gamma radiation. (Kamimura, M.)

  2. Fuels planning: science synthesis and integration; social issues fact sheet 06: Important considerations for communicating about hazards

    Science.gov (United States)

    Rocky Mountain Research Station USDA Forest Service

    2004-01-01

    Effective public education and communication campaigns about wildland fire and fuels management should have clear objectives, and use the right techniques to achieve these objectives. This fact sheet lists seven important considerations for planning or implementing a hazard communication effort.

  3. Ice sheet anisotropy measured with polarimetric ice sounding radar

    DEFF Research Database (Denmark)

    Dall, Jørgen

    2010-01-01

    For polar ice sheets, valuable stress and strain information can be deduced from crystal orientation fabrics (COF) and their prevailing c-axis alignment. Polarimetric radio echo sounding is a promising technique to measure the anisotropic electromagnetic propagation and reflection properties asso...

  4. Careers "Fact Sheets" for clinical engineering & biomedical technology.

    Science.gov (United States)

    Pacela, A F

    1991-01-01

    Three Careers "Fact Sheets" include information on CE and BMET job titles, job descriptions, and certification. These materials are intended to aid in furthering professional recognition for Clinical Engineers and BMETs, and may be useful in communicating with Administration or Human Resources departments.

  5. Epilepsy. Fact Sheet = Epilepsia. Hojas Informativas Sobre Discapacidades.

    Science.gov (United States)

    National Information Center for Children and Youth with Disabilities, Washington, DC.

    This fact sheet, written in both English and Spanish, provides a definition, information on incidence, typical characteristics, and educational implications of epilepsy. It notes that epilepsy is classified as "other health impaired" under the Individuals with Disabilities Education Act (IDEA) and that children with epilepsy or seizure disorders…

  6. Whooping Cough (Pertussis) - Fact Sheet for Parents

    Science.gov (United States)

    ... months 4 through 6 years Fact Sheet for Parents Color [2 pages] Español: Tosferina (pertussis) The best ... according to the recommended schedule. Fact Sheets for Parents Diseases and the Vaccines that Prevent Them Chickenpox ...

  7. AER benchmark specification sheet

    International Nuclear Information System (INIS)

    Aszodi, A.; Toth, S.

    2009-01-01

    In the VVER-440/213 type reactors, the core outlet temperature field is monitored with in-core thermocouples, which are installed above 210 fuel assemblies. These measured temperatures are used in determination of the fuel assembly powers and they have important role in the reactor power limitation. For these reasons, correct interpretation of the thermocouple signals is an important question. In order to interpret the signals in correct way, knowledge of the coolant mixing in the assembly heads is necessary. Computational Fluid Dynamics (CFD) codes and experiments can help to understand better these mixing processes and they can provide information which can support the more adequate interpretation of the thermocouple signals. This benchmark deals with the 3D CFD modeling of the coolant mixing in the heads of the profiled fuel assemblies with 12.2 mm rod pitch. Two assemblies of the 23rd cycle of the Paks NPP's Unit 3 are investigated. One of them has symmetrical pin power profile and another possesses inclined profile. (authors)

  8. AER Benchmark Specification Sheet

    International Nuclear Information System (INIS)

    Aszodi, A.; Toth, S.

    2009-01-01

    In the WWER-440/213 type reactors, the core outlet temperature field is monitored with in-core thermocouples, which are installed above 210 fuel assemblies. These measured temperatures are used in determination of the fuel assembly powers and they have important role in the reactor power limitation. For these reasons, correct interpretation of the thermocouple signals is an important question. In order to interpret the signals in correct way, knowledge of the coolant mixing in the assembly heads is necessary. Computational fluid dynamics codes and experiments can help to understand better these mixing processes and they can provide information which can support the more adequate interpretation of the thermocouple signals. This benchmark deals with the 3D computational fluid dynamics modeling of the coolant mixing in the heads of the profiled fuel assemblies with 12.2 mm rod pitch. Two assemblies of the twenty third cycle of the Paks NPPs Unit 3 are investigated. One of them has symmetrical pin power profile and another possesses inclined profile. (Authors)

  9. Nuclear accident dosimetry. Revision of emergency data sheets

    International Nuclear Information System (INIS)

    Delafield, H.J.

    1976-09-01

    The Emergency Data Sheets on Nuclear Accident Dosimetry have been revealed following the publication of a three part manual on this subject (Delafield, Dennis and Gibson, AERE-R 7485/6/7, 1973). This memo provides an explanation of the action levels adopted for the initial segregation of irradiated persons following a criticality accident, by monitoring the activity of indium foils contained in personnel dosimeters and the induced body sodium activity. The data sheets are given as an Appendix. They provide basic information on; the segregation of irradiated persons, the estimation of radiation exposure, and the assessment of personnel γ-ray and neutron doses. (author)

  10. Object-Based Benefits without Object-Based Representations

    OpenAIRE

    Alvarez, George Angelo; Fougnie, Daryl; Cormiea, Sarah M

    2012-01-01

    The organization of visual information into objects strongly influences visual memory: Displays with objects defined by two features (e.g. color, orientation) are easier to remember than displays with twice as many objects defined by one feature (Olson & Jiang, 2002). Existing theories suggest that this ‘object-benefit’ is based on object-based limitations in working memory: because a limited number of objects can be stored, packaging features together so that fewer objects have to be remembe...

  11. Objects of Desire.

    Science.gov (United States)

    Zielinski, Dave

    2000-01-01

    Describes learning objects, also known as granules, chunks, or information nuggets, and likens them to help screens. Discusses concerns about how they can go wrong: (1) faulty pretest questions; (2) missing links in the learning object chain; (3) poor frames of reference; and (4) lack of customization. (JOW)

  12. Location mortgage in accounting objects

    Directory of Open Access Journals (Sweden)

    I.M. Vygiska

    2015-12-01

    Full Text Available The article analyzes the mechanism of the implementation of all kinds of mortgage (mortgage, pledge, mortgage of securities, security of property rights, the mortgage of goods in circulation or processing, tax lien defined the specificity of receipt/return of the mortgage, particularly payments between mortgagor and the mortgagee. Determine the subject property entities that can act as mortgage; identified by their place in the system of objects of accounting mortgagor and the mortgagee. The peculiarities of the balance sheet and off-balance sheet assets as a reflection of your collateral. Identified two groups of mortgage transactions: transactions with mortgage for its receipt and transmission; business transactions related to the conditions of loan agreements (loan and mortgage. The results are shown in the research paper proposals allow for further research to develop mortgage organizational and methodological support the operations accounting for the effective management of financial resources and obligations, collateralised.

  13. 21 CFR 880.5180 - Burn sheet.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Burn sheet. 880.5180 Section 880.5180 Food and... Burn sheet. (a) Identification. A burn sheet is a device made of a porous material that is wrapped aroung a burn victim to retain body heat, to absorb wound exudate, and to serve as a barrier against...

  14. Manifold free multiple sheet superplastic forming

    Science.gov (United States)

    Elmer, John W.; Bridges, Robert L.

    2004-01-13

    Fluid-forming compositions in a container attached to enclosed adjacent sheets are heated to relatively high temperatures to generate fluids (gases) that effect inflation of the sheets. Fluid rates to the enclosed space between the sheets can be regulated by the canal from the container. Inflated articles can be produced by a continuous, rather than batch-type, process.

  15. On the possible eigenoscillations of neutral sheets

    International Nuclear Information System (INIS)

    Almeida, W.A.; Costa, J.M. da; Aruquipa, E.G.; Sudano, J.P.

    1974-12-01

    A neutral sheet model with hyperbolic tangent equilibrium magnetic field and hyperbolic square secant density profiles is considered. It is shown that the equation for small oscillations takes the form of an eigenvalue oscillation problem. Computed eigenfrequencies of the geomagnetic neutral sheet were found to be in the range of the resonant frequencies of the geomagnetic plasma sheet computed by other authors

  16. Final Rule to Reduce Toxic Air Pollutants from Surface Coating of Plastic Parts and Products Fact Sheet

    Science.gov (United States)

    This page contains an August 2004 fact sheet with information regarding the final NESHAP for Surface Coating of Plastic Parts and Products. This document provides a summary of the information for the information for this regulation.

  17. Correlated motions are a fundamental property of β-sheets

    Science.gov (United States)

    Fenwick, R. Bryn; Orellana, Laura; Esteban-Martín, Santi; Orozco, Modesto; Salvatella, Xavier

    2014-06-01

    Correlated motions in proteins can mediate fundamental biochemical processes such as signal transduction and allostery. The mechanisms that underlie these processes remain largely unknown due mainly to limitations in their direct detection. Here, based on a detailed analysis of protein structures deposited in the protein data bank, as well as on state-of-the art molecular simulations, we provide general evidence for the transfer of structural information by correlated backbone motions, mediated by hydrogen bonds, across β-sheets. We also show that the observed local and long-range correlated motions are mediated by the collective motions of β-sheets and investigate their role in large-scale conformational changes. Correlated motions represent a fundamental property of β-sheets that contributes to protein function.

  18. Drumlinised glaciofluvial and glaciolacustrine sediments on the Småland peneplain, South Sweden - new information on the growth and decay history of the Fennoscandian Ice Sheets during MIS 3

    Science.gov (United States)

    Möller, Per; Murray, Andrew S.

    2015-08-01

    Dug trenches in sediment-cored drumlins on the Småland peneplain, southern Sweden, occurring intermixed with rock-cored drumlins, revealed sedimentary successions and facies suggesting that the core sediments were primarily deposited proglacially, both in glaciolacustrine settings as delta-front and more distal deeper-water sediments, and as glaciofluvial braidplain sediments. From the relationship between the drumlin sorted-sediment cores and their surficial drape by a till carapace, it is concluded that erosion was the main drumlin-forming process here, reshaping the original sediment morphology into streamlined landforms, after which a more or less thick traction till was deposited over the eroded and/or deformed ice-bed interface. Drumlin formation probably took place during the last deglaciation over the area. The drumlin-core sediments in 14 excavated trenches were dated by Optically Stimulated Luminescence (OSL); most retrieved ages fall into two distinct groups, both within Marine Isotope Stage 3 (c. 60-30 ka). When plotted as mean OSL ages for each site, all but two sites fall either into an older age group, c. 48-56 ka (seven sites), or into a younger age group, c. 28-38 ka (five sites). These age intervals correlate well with the suggested time spans for the Ristinge and Klintholm ice advances in Denmark by ice flowing from the Baltic Basin westwards, terminating in fan-shaped patterns. These interstadial ice advances in the southwestern sector of the Fennoscandian Ice Sheet give rise to enigmatic questions on the physics and mechanics of ice sheet build-up and decay, especially as palaeoenvironmental data for northern Fennoscandia suggest widespread ice-free conditions within roughly the same time fame as the recorded ice advances in the south.

  19. The detection and prevention of manipulations in the balance sheet and the cash flow statement

    Directory of Open Access Journals (Sweden)

    Dragomir Dimitrijevic

    2015-08-01

    Full Text Available Financial statements which consist of objective, real and reliable information represent the key basis for making many business decisions. If, when writing financial statements, certain manipulation techniques are used for displaying the best possible results of transactions, the quality of financial reports will be endangered. Many financial frauds have led to a great mistrust in the system of financial reporting and the profession of accounting and auditing, which are often accused of the emergence of fraud and losing trust in the reliability of financial information by many users and economic decision makers. These are the reasons why the paper discusses the techniques of manipulation in financial statements, especially in balance sheets and cash flow statements, since these forms of manipulation are harder to detect and prevent when compared to manipulations of revenues and expenses in the income statement.

  20. Objects, materiality and meaning

    DEFF Research Database (Denmark)

    Lenau, Torben Anker; Lindegaard, Hanne

    2008-01-01

    The present research work investigates the relation between physical objects, their materiality, understood as the physical substances they are made from, and the communication from the objects. In product design of physical objects the communicative aspects are just as important as the function...... of the object, and the designers aim is therefore to tune both in order to achieve a desired goal. To do so the designer basically has 2 options: Alteration of the physical shape of the object and the selection of materials. Through the manipulation of shape and materials can symbolic and sensory information...... be written into the object. The materials are therefore carriers of communication, even though this is dependent of the cultural context and the environment which the object will be part of. However the designer has only minor influence on those....

  1. Fashion Objects

    DEFF Research Database (Denmark)

    Andersen, Bjørn Schiermer

    2009-01-01

    -- an outline which at the same time indicates the need for transformations of the Durkheimian model on decisive points. Thus, thirdly, it returns to Durkheim and undertakes to develop his concepts in a direction suitable for a sociological theory of fashion. Finally, it discusses the theoretical implications......This article attempts to create a framework for understanding modern fashion phenomena on the basis of Durkheim's sociology of religion. It focuses on Durkheim's conception of the relation between the cult and the sacred object, on his notion of 'exteriorisation', and on his theory of the social...... symbol in an attempt to describe the peculiar attraction of the fashion object and its social constitution. However, Durkheim's notions of cult and ritual must undergo profound changes if they are to be used in an analysis of fashion. The article tries to expand the Durkheimian cult, radically enlarging...

  2. Utilities objectives

    International Nuclear Information System (INIS)

    Cousin, Y.; Fabian, H.U.

    1996-01-01

    The policy of French and german utilities is to make use of nuclear energy as a long term, competitive and environmentally friendly power supply. The world electricity generation is due to double within the next 30 years. In the next 20 to 30 years the necessity of nuclear energy will be broadly recognized. More than for most industries, to deal properly with nuclear energy requires the combination of a consistent political will, of a proper institutional framework, of strong and legitimate control authorities, of a sophisticated industry and of operators with skilled management and human resources. One of the major risk facing nuclear energy is the loss of competitiveness. This can be achieved only through the combination of an optimized design, a consistent standardization, a proper industrial partnership and a stable long term strategy. Although the existing plants in Western Europe are already very safe, the policy is clearly to enhance the safety of the next generation of nuclear plants which are designing today. The French and German utilities have chosen an evolutionary approach based on experience and proven technologies, with an enhanced defense in depth and an objective of easier operation and maintenance. The cost objective is to maintain and improve what has been achieved in the best existing power plants in both countries. This calls for rational choices and optimized design to meet the safety objectives, a strong standardization policy, short construction times, high availability and enough flexibility to enable optimization of the fuel cycle throughout the lifetime of the plants. The conceptual design phase has proven that the French and German teams from industry and from the utilities are able to pursue both the safety and the cost objectives, basing their decision on a rational approach which could be accepted by the safety authorities. (J.S.)

  3. Periodic folding of viscous sheets

    Science.gov (United States)

    Ribe, Neil M.

    2003-09-01

    The periodic folding of a sheet of viscous fluid falling upon a rigid surface is a common fluid mechanical instability that occurs in contexts ranging from food processing to geophysics. Asymptotic thin-layer equations for the combined stretching-bending deformation of a two-dimensional sheet are solved numerically to determine the folding frequency as a function of the sheet’s initial thickness, the pouring speed, the height of fall, and the fluid properties. As the buoyancy increases, the system bifurcates from “forced” folding driven kinematically by fluid extrusion to “free” folding in which viscous resistance to bending is balanced by buoyancy. The systematics of the numerically predicted folding frequency are in good agreement with laboratory experiments.

  4. Systematic logging utilizing a log sheet designed for drill core descriptions. An example in uranium exploration activities

    International Nuclear Information System (INIS)

    Sasao, Eiji; Tsuruta, Tadahiko; Iida, Yoshimasa

    2000-01-01

    We describe the log sheets used during uranium exploration activities for unconformity-related uranium deposits by JNC. The purpose of using the logging sheets is to standardize the objects which all geologists must observe and for data quality assurance. The log sheets are a three-part set describing basement lithology, sandstone lithology and geotechnics. We devised our own log sheets to describe both the sandstone and the underlying basement rock when we started exploration in Athabasca Basin, Canada. We modified the sheets to gain a better understanding of the geological features related to uranium mineralization, and made final improvements to satisfy required quality based on the criteria of descriptive objects and accuracy. Use of the log sheets resulted in effective performance of core logging and improvement in the display of data. (author)

  5. Load Test in Sheet Pile

    OpenAIRE

    Luis Orlando Ibanez

    2016-01-01

    In this work, are discussed experiences in the use of mathematical modeling and testing in hydraulic engineering structures. For this purpose the results of load tests in sheet pile, evaluating horizontal and vertical deformations that occur in the same exposed. Comparisons between theoretical methods for calculating deformations and mathematical models based on the Finite Element Method are established. Finally, the coincidence between the numerical model and the results of the load test ful...

  6. Ohm's law for a current sheet

    Science.gov (United States)

    Lyons, L. R.; Speiser, T. W.

    1985-01-01

    The paper derives an Ohm's law for single-particle motion in a current sheet, where the magnetic field reverses in direction across the sheet. The result is considerably different from the resistive Ohm's law often used in MHD studies of the geomagnetic tail. Single-particle analysis is extended to obtain a self-consistency relation for a current sheet which agrees with previous results. The results are applicable to the concept of reconnection in that the electric field parallel to the current is obtained for a one-dimensional current sheet with constant normal magnetic field. Dissipated energy goes directly into accelerating particles within the current sheet.

  7. A flexible tactile sensitive sheet using a hetero-core fiber optic sensor

    Science.gov (United States)

    Fujino, S.; Yamazaki, H.; Hosoki, A.; Watanabe, K.

    2014-05-01

    In this report, we have designed a tactile sensitive sheet based on a hetero-core fiber-optic sensor, which realize an areal sensing by using single sensor potion in one optical fiber line. Recently, flexible and wide-area tactile sensing technology is expected to applied to acquired biological information in living space and robot achieve long-term care services such as welfare and nursing-care and humanoid technology. A hetero-core fiber-optic sensor has several advantages such as thin and flexible transmission line, immunity to EMI. Additionally this sensor is sensitive to moderate bending actions with optical loss changes and is independent of temperature fluctuation. Thus, the hetero-core fiber-optic sensor can be suitable for areal tactile sensing. We measure pressure characteristic of the proposed sensitive sheet by changing the pressure position and pinching characteristic on the surface. The proposed tactile sensitive sheet shows monotonic responses on the whole sensitive sheet surface although different sensitivity by the position is observed at the sensitive sheet surface. Moreover, the tactile sensitive sheet could sufficiently detect the pinching motion. In addition, in order to realize the discrimination between pressure and pinch, we fabricated a doubled-over sensor using a set of tactile sensitive sheets, which has different kinds of silicon robbers as a sensitive sheet surface. In conclusion, the flexible material could be given to the tactile sensation which is attached under proposed sensitive sheet.

  8. Advanced Gradient Based Optimization Techniques Applied on Sheet Metal Forming

    International Nuclear Information System (INIS)

    Endelt, Benny; Nielsen, Karl Brian

    2005-01-01

    The computational-costs for finite element simulations of general sheet metal forming processes are considerable, especially measured in time. In combination with optimization, the performance of the optimization algorithm is crucial for the overall performance of the system, i.e. the optimization algorithm should gain as much information about the system in each iteration as possible. Least-square formulation of the object function is widely applied for solution of inverse problems, due to the superior performance of this formulation.In this work focus will be on small problems which are defined as problems with less than 1000 design parameters; as the majority of real life optimization and inverse problems, represented in literature, can be characterized as small problems, typically with less than 20 design parameters.We will show that the least square formulation is well suited for two classes of inverse problems; identification of constitutive parameters and process optimization.The scalability and robustness of the approach are illustrated through a number of process optimizations and inverse material characterization problems; tube hydro forming, two step hydro forming, flexible aluminum tubes, inverse identification of material parameters

  9. Information

    International Nuclear Information System (INIS)

    Boyard, Pierre.

    1981-01-01

    The fear for nuclear energy and more particularly for radioactive wastes is analyzed in the sociological context. Everybody agree on the information need, information is available but there is a problem for their diffusion. Reactions of the public are analyzed and journalists, scientists and teachers have a role to play [fr

  10. Experimental formability analysis of bondal sandwich sheet

    Science.gov (United States)

    Kami, Abdolvahed; Banabic, Dorel

    2018-05-01

    Metal/polymer/metal sandwich sheets have recently attracted the interests of industries like automotive industry. These sandwich sheets have superior properties over single-layer metallic sheets including good sound and vibration damping and light weight. However, the formability of these sandwich sheets should be enhanced which requires more research. In this paper, the formability of Bondal sheet (DC06/viscoelastic polymer/DC06 sandwich sheet) was studied through different types of experiments. The mechanical properties of Bondal were determined by uniaxial tensile tests. Hemispherical punch stretching and hydraulic bulge tests were carried out to determine the forming limit diagram (FLD) of Bondal. Furthermore, cylindrical and square cup drawing tests were performed in dry and oil lubricated conditions. These tests were conducted at different blank holding forces (BHFs). An interesting observation about Bondal sheet deep drawing was obtaining of higher drawing depths at dry condition in comparison with oil-lubricated condition.

  11. Buckling and stretching of thin viscous sheets

    Science.gov (United States)

    O'Kiely, Doireann; Breward, Chris; Griffiths, Ian; Howell, Peter; Lange, Ulrich

    2016-11-01

    Thin glass sheets are used in smartphone, battery and semiconductor technology, and may be manufactured by producing a relatively thick glass slab and subsequently redrawing it to a required thickness. The resulting sheets commonly possess undesired centerline ripples and thick edges. We present a mathematical model in which a viscous sheet undergoes redraw in the direction of gravity, and show that, in a sufficiently strong gravitational field, buckling is driven by compression in a region near the bottom of the sheet, and limited by viscous resistance to stretching of the sheet. We use asymptotic analysis in the thin-sheet, low-Reynolds-number limit to determine the centerline profile and growth rate of such a viscous sheet.

  12. Breaking object correspondence across saccadic eye movements deteriorates object recognition

    Directory of Open Access Journals (Sweden)

    Christian H. Poth

    2015-12-01

    Full Text Available Visual perception is based on information processing during periods of eye fixations that are interrupted by fast saccadic eye movements. The ability to sample and relate information on task-relevant objects across fixations implies that correspondence between presaccadic and postsaccadic objects is established. Postsaccadic object information usually updates and overwrites information on the corresponding presaccadic object. The presaccadic object representation is then lost. In contrast, the presaccadic object is conserved when object correspondence is broken. This helps transsaccadic memory but it may impose attentional costs on object recognition. Therefore, we investigated how breaking object correspondence across the saccade affects postsaccadic object recognition. In Experiment 1, object correspondence was broken by a brief postsaccadic blank screen. Observers made a saccade to a peripheral object which was displaced during the saccade. This object reappeared either immediately after the saccade or after the blank screen. Within the postsaccadic object, a letter was briefly presented (terminated by a mask. Observers reported displacement direction and letter identity in different blocks. Breaking object correspondence by blanking improved displacement identification but deteriorated postsaccadic letter recognition. In Experiment 2, object correspondence was broken by changing the object’s contrast-polarity. There were no object displacements and observers only reported letter identity. Again, breaking object correspondence deteriorated postsaccadic letter recognition. These findings identify transsaccadic object correspondence as a key determinant of object recognition across the saccade. This is in line with the recent hypothesis that breaking object correspondence results in separate representations of presaccadic and postsaccadic objects which then compete for limited attentional processing resources (Schneider, 2013. Postsaccadic

  13. Data sheets on selected toxic elements

    International Nuclear Information System (INIS)

    Jaworski, J.F.

    1982-01-01

    The chemical elements considered in this volume have been identified as toxic to animal and vegetable life forms; however, these elements have not been studied as intensely as lead, mercury, cadmium, etc. Since, in most cases, existing data are insufficient to permit discussion and comparisons of relative quality, it was decided to present what quantitative data there are in as concise a manner as possible. The resulting data sheets present what is considered to be the best available information on the environmental levels, emissions and toxicology of these elements and some of their compounds. Reference is made to the article or review in which the datum appears and which may contain any discussion of the datum and the methods whereby it was obtained. Elements considered in this volume are antimony, barium, beryllium, bismuth, boron, cesium, gallium, germanium, indium, molybdenum, silver, tellurium, thallium, tin, uranium and zirconium

  14. The pedagogical possibilities in the education of scientific research methodology in information science and the scientific objects of this field: durkheim approaches

    OpenAIRE

    Francisco das Chagas de Souza

    2003-01-01

    This article results of bibliographical, exploratory and qualitative research. Its argues that three approaches are gifts in the educational process of discipline of the Scientific Research Methodology in Information Science. They are the social facts of the Information Science, the types of the research and the social theory. It sees that the pedagogical possibilities of the education of Scientific Methodology in Information Science are related with the practical one of the writing which dep...

  15. Energy-Saving Opportunities for Manufacturing Companies, International Fact Sheet (Spanish)

    Energy Technology Data Exchange (ETDEWEB)

    2010-08-01

    This English/Spanish fact sheet describes the Industrial Technologies Program Save Energy Now model and provides information on tools and resources to help manufacturing facilities reduce industrial energy intensity.

  16. Fact Sheet: Notice of Ambient Water Quality Criteria Document for Tributyltin (TBT) - Final

    Science.gov (United States)

    Information pertaining to 2004 Final Acute and Chronic Ambient Aquatic Life Water Quality Criteria for Tributyltin (TBT) for freshwater and saltwater. This fact sheet includes the safe levels of TBT that should protect the majority of species.

  17. Guidelines for Home Energy Upgrade Professionals: Standard Work Specifications for Multifamily Energy Upgrades (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2011-08-01

    This fact sheet provides essential information about the 2011 publication of the Workforce Guidelines for Multifamily Home Energy Upgrades, including their origin, their development with the help of industry leaders to create the standard work specifications for retrofit work.

  18. Formation and interpretation of eskers beneath retreating ice sheets

    Science.gov (United States)

    Creyts, T. T.; Hewitt, I.

    2017-12-01

    The retreat of the ice sheets during the Pleistocene left large and spectacular subglacial features exposed. Understanding these features gives us insight into how the ice sheets retreated, how meltwater influenced retreat, and can help inform our understanding of potential future rates of ice sheet retreat. Among these features, eskers, long sinuous ridges primarily composed of clastic sediments, lack a detailed explanation of how surface melt rates and ice sheet retreat rates influence their growth and spatial distribution. Here, we develop a theory for esker formation based on the initial work of Rothlisberger modified for sediment transport and inclusion of surface meltwater forcing. The primary subglacial ingredients include water flow through subglacial tunnels with the addition of mass balances for sediment transport. We show how eskers when water flow slows below a critical stress for sediment motion. This implies that eskers are deposited in a localized region near the snout of the ice sheet. Our findings suggest that very long eskers form sequentially as the ice front retreats. The position of the esker follows the path of the channel mouth through time, which does not necessarily coincide with the instantaneous route of the feeding channel. However, in most cases, we expect those locations to be similar. The role of surface meltwater and the climatology associated with the forcing is crucial to the lateral spacing of the eskers. We predict that high surface melt rates lead to narrower catchments but that the greater extent of the ablation area means that channels are likely larger. At the same time, for a given channel size (and hence sediment flux), the size of a deposited esker depends on a margin retreat rate. Hence, the size of the eskers is related delicately to the balance between surface melt rates and margin retreat rates. We discuss how our theory can be combined with observed esker distributions to infer the relationship between these two rates

  19. Uncertainty Quantification for Ice Sheet Science and Sea Level Projections

    Science.gov (United States)

    Boening, C.; Schlegel, N.; Limonadi, D.; Schodlok, M.; Seroussi, H. L.; Larour, E. Y.; Watkins, M. M.

    2017-12-01

    In order to better quantify uncertainties in global mean sea level rise projections and in particular upper bounds, we aim at systematically evaluating the contributions from ice sheets and potential for extreme sea level rise due to sudden ice mass loss. Here, we take advantage of established uncertainty quantification tools embedded within the Ice Sheet System Model (ISSM) as well as sensitivities to ice/ocean interactions using melt rates and melt potential derived from MITgcm/ECCO2. With the use of these tools, we conduct Monte-Carlo style sampling experiments on forward simulations of the Antarctic ice sheet, by varying internal parameters and boundary conditions of the system over both extreme and credible worst-case ranges. Uncertainty bounds for climate forcing are informed by CMIP5 ensemble precipitation and ice melt estimates for year 2100, and uncertainty bounds for ocean melt rates are derived from a suite of regional sensitivity experiments using MITgcm. Resulting statistics allow us to assess how regional uncertainty in various parameters affect model estimates of century-scale sea level rise projections. The results inform efforts to a) isolate the processes and inputs that are most responsible for determining ice sheet contribution to sea level; b) redefine uncertainty brackets for century-scale projections; and c) provide a prioritized list of measurements, along with quantitative information on spatial and temporal resolution, required for reducing uncertainty in future sea level rise projections. Results indicate that ice sheet mass loss is dependent on the spatial resolution of key boundary conditions - such as bedrock topography and melt rates at the ice-ocean interface. This work is performed at and supported by the California Institute of Technology's Jet Propulsion Laboratory. Supercomputing time is also supported through a contract with the National Aeronautics and Space Administration's Cryosphere program.

  20. When complex is easy on the mind: internal repetition of visual information in complex objects is a source of perceptual fluency

    NARCIS (Netherlands)

    Linda Steg; Roos Pals; Ayça Berfu Ünal; Yannick Joye

    2015-01-01

    Across 3 studies, we investigated whether visual complexity deriving from internally repeating visual information over many scale levels is a source of perceptual fluency. Such continuous repetition of visual information is formalized in fractal geometry and is a key-property of natural structures.

  1. The Forming of AISI 409 sheets for fan blade manufacturing

    International Nuclear Information System (INIS)

    Foroni, F. D.; Menezes, M. A.; Moreira Filho, L. A.

    2007-01-01

    The necessity of adapting the standardized fan models to conditions of higher temperature has emerged due to the growth of concern referring to the consequences of the gas expelling after the Mont Blanc tunnel accident in Italy and France, where even though, with 100 fans in operation, 41 people died. The objective of this work is to present an alternative to the market standard fans considering a new technology in constructing blades. This new technology introduces the use of the stainless steel AISI 409 due to its good to temperatures of gas exhaust from tunnels in fire situation. The innovation is centered in the process of a deep drawing of metallic sheets in order to keep the ideal aerodynamic superficies for the fan ideal performance. Through the impression of circles on the sheet plane it is shown, experimentally, that, during the pressing process, the more deformed regions on the sheet plane of the blade can not reach the deformation limits of the utilized sheet material

  2. Vietnamese Hurricane Response Fact Sheets

    Science.gov (United States)

    Các tờ dữ kiện được cung cấp nơi đây mô tả vai trò của EPA trong việc đáp ứng với bão và cách các chương trình cụ thể cung cấp sự hỗ trợ. The Vietnamese fact sheets provided here describe EPA's role in a hurricane response.

  3. Ice Sheet Roughness Estimation Based on Impulse Responses Acquired in the Global Ice Sheet Mapping Orbiter Mission

    Science.gov (United States)

    Niamsuwan, N.; Johnson, J. T.; Jezek, K. C.; Gogineni, P.

    2008-12-01

    The Global Ice Sheet Mapping Orbiter (GISMO) mission was developed to address scientific needs to understand the polar ice subsurface structure. This NASA Instrument Incubator Program project is a collaboration between Ohio State University, the University of Kansas, Vexcel Corporation and NASA. The GISMO design utilizes an interferometric SAR (InSAR) strategy in which ice sheet reflected signals received by a dual-antenna system are used to produce an interference pattern. The resulting interferogram can be used to filter out surface clutter so as to reveal the signals scattered from the base of the ice sheet. These signals are further processed to produce 3D-images representing basal topography of the ice sheet. In the past three years, the GISMO airborne field campaigns that have been conducted provide a set of useful data for studying geophysical properties of the Greenland ice sheet. While topography information can be obtained using interferometric SAR processing techniques, ice sheet roughness statistics can also be derived by a relatively simple procedure that involves analyzing power levels and the shape of the radar impulse response waveforms. An electromagnetic scattering model describing GISMO impulse responses has previously been proposed and validated. This model suggested that rms-heights and correlation lengths of the upper surface profile can be determined from the peak power and the decay rate of the pulse return waveform, respectively. This presentation will demonstrate a procedure for estimating the roughness of ice surfaces by fitting the GISMO impulse response model to retrieved waveforms from selected GISMO flights. Furthermore, an extension of this procedure to estimate the scattering coefficient of the glacier bed will be addressed as well. Planned future applications involving the classification of glacier bed conditions based on the derived scattering coefficients will also be described.

  4. Informe

    Directory of Open Access Journals (Sweden)

    Egon Lichetenberger

    1950-10-01

    Full Text Available Informe del doctor Egon Lichetenberger ante el Consejo Directivo de la Facultad, sobre el  curso de especialización en Anatomía Patológica patrocinado por la Kellogg Foundation (Departamento de Patología

  5. AI applications in sheet metal forming

    CERN Document Server

    Hussein, Hussein

    2017-01-01

    This book comprises chapters on research work done around the globe in the area of artificial intelligence (AI) applications in sheet metal forming. The first chapter offers an introduction to various AI techniques and sheet metal forming, while subsequent chapters describe traditional procedures/methods used in various sheet metal forming processes, and focus on the automation of those processes by means of AI techniques, such as KBS, ANN, GA, CBR, etc. Feature recognition and the manufacturability assessment of sheet metal parts, process planning, strip-layout design, selecting the type and size of die components, die modeling, and predicting die life are some of the most important aspects of sheet metal work. Traditionally, these activities are highly experience-based, tedious and time consuming. In response, researchers in several countries have applied various AI techniques to automate these activities, which are covered in this book. This book will be useful for engineers working in sheet metal industri...

  6. Dynamics of Radially Expanding Liquid Sheets

    Science.gov (United States)

    Majumdar, Nayanika; Tirumkudulu, Mahesh S.

    2018-04-01

    The process of atomization often involves ejecting thin liquid sheets at high speeds from a nozzle that causes the sheet to flap violently and break up into fine droplets. The flapping of the liquid sheet has long been attributed to the sheet's interaction with the surrounding gas phase. Here, we present experimental evidence to the contrary and show that the flapping is caused by the thinning of the liquid sheet as it spreads out from the nozzle exit. The measured growth rates of the waves agree remarkably well with the predictions of a recent theory that accounts for the sheet's thinning but ignores aerodynamic interactions. We anticipate these results to not only lead to more accurate predictions of the final drop-size distribution but also enable more efficient designs of atomizers.

  7. Elaboration of the technology of forming a conical product of sheet metal

    Directory of Open Access Journals (Sweden)

    W. Matysiak

    2010-01-01

    Full Text Available The work presents a general knowledge about spinning draw pieces of sheets, one of multi-operational processes of spinning a sheet metal conical product without machining. The objective of the work was to elaborate both the technology of forming conical products of sheet metal and execution of technological tests as well as to determine the technological parameters for the process of spinning a conical insert. As a result of the investigations, the products with improved mechanical properties, stricter execution tolerance and low roughness have been obtained. The series of 200 prototype conical inserts for the shipbuilding industry have been made.

  8. Groundwater flow modelling under ice sheet conditions. Scoping calculations

    Energy Technology Data Exchange (ETDEWEB)

    Jaquet, O.; Namar, R. (In2Earth Modelling Ltd (Switzerland)); Jansson, P. (Dept. of Physical Geography and Quaternary Geology, Stockholm Univ., Stockholm (Sweden))

    2010-10-15

    The potential impact of long-term climate changes has to be evaluated with respect to repository performance and safety. In particular, glacial periods of advancing and retreating ice sheet and prolonged permafrost conditions are likely to occur over the repository site. The growth and decay of ice sheets and the associated distribution of permafrost will affect the groundwater flow field and its composition. As large changes may take place, the understanding of groundwater flow patterns in connection to glaciations is an important issue for the geological disposal at long term. During a glacial period, the performance of the repository could be weakened by some of the following conditions and associated processes: - Maximum pressure at repository depth (canister failure). - Maximum permafrost depth (canister failure, buffer function). - Concentration of groundwater oxygen (canister corrosion). - Groundwater salinity (buffer stability). - Glacially induced earthquakes (canister failure). Therefore, the GAP project aims at understanding key hydrogeological issues as well as answering specific questions: - Regional groundwater flow system under ice sheet conditions. - Flow and infiltration conditions at the ice sheet bed. - Penetration depth of glacial meltwater into the bedrock. - Water chemical composition at repository depth in presence of glacial effects. - Role of the taliks, located in front of the ice sheet, likely to act as potential discharge zones of deep groundwater flow. - Influence of permafrost distribution on the groundwater flow system in relation to build-up and thawing periods. - Consequences of glacially induced earthquakes on the groundwater flow system. Some answers will be provided by the field data and investigations; the integration of the information and the dynamic characterisation of the key processes will be obtained using numerical modelling. Since most of the data are not yet available, some scoping calculations are performed using the

  9. Groundwater flow modelling under ice sheet conditions. Scoping calculations

    International Nuclear Information System (INIS)

    Jaquet, O.; Namar, R.; Jansson, P.

    2010-10-01

    The potential impact of long-term climate changes has to be evaluated with respect to repository performance and safety. In particular, glacial periods of advancing and retreating ice sheet and prolonged permafrost conditions are likely to occur over the repository site. The growth and decay of ice sheets and the associated distribution of permafrost will affect the groundwater flow field and its composition. As large changes may take place, the understanding of groundwater flow patterns in connection to glaciations is an important issue for the geological disposal at long term. During a glacial period, the performance of the repository could be weakened by some of the following conditions and associated processes: - Maximum pressure at repository depth (canister failure). - Maximum permafrost depth (canister failure, buffer function). - Concentration of groundwater oxygen (canister corrosion). - Groundwater salinity (buffer stability). - Glacially induced earthquakes (canister failure). Therefore, the GAP project aims at understanding key hydrogeological issues as well as answering specific questions: - Regional groundwater flow system under ice sheet conditions. - Flow and infiltration conditions at the ice sheet bed. - Penetration depth of glacial meltwater into the bedrock. - Water chemical composition at repository depth in presence of glacial effects. - Role of the taliks, located in front of the ice sheet, likely to act as potential discharge zones of deep groundwater flow. - Influence of permafrost distribution on the groundwater flow system in relation to build-up and thawing periods. - Consequences of glacially induced earthquakes on the groundwater flow system. Some answers will be provided by the field data and investigations; the integration of the information and the dynamic characterisation of the key processes will be obtained using numerical modelling. Since most of the data are not yet available, some scoping calculations are performed using the

  10. Registration of Space Objects

    Science.gov (United States)

    Schmidt-Tedd, Bernhard

    2017-07-01

    Space objects are subject to registration in order to allocate "jurisdiction and control" over those objects in the sovereign-free environment of outer space. This approach is similar to the registration of ships in view of the high sea and for aircrafts with respect to the international airspace. Registration is one of the basic principles of space law, starting with UN General Assembly Resolution 1721 B (XVI) of December 20, 1961, followed by Resolution 1962 (XVIII) of December 13, 1963, then formulated in Article VIII of the Outer Space Treaty of 1967 and as specified in the Registration Convention of 1975. Registration of space objects can be seen today as a principle of customary international law, relevant for each spacefaring state. Registration is divided into a national and an international level. The State Party establishes a national registry for its space objects, and those registrations have to be communicated via diplomatic channel to the UN Register of space objects. This UN Register is handled by the UN Office for Outer Space Affairs (UNOOSA) and is an open source of information for space objects worldwide. Registration is linked to the so-called launching state of the relevant space object. There might be more than one launching state for the specific launch event, but only one state actor can register a specific space object. The state of registry gains "jurisdiction and control" over the space object and therefore no double registration is permissible. Based on the established UN Space Law, registration practice was subject to some adaptions due to technical developments and legal challenges. After the privatization of the major international satellite organizations, a number of non-registrations had to be faced. The state actors reacted with the UN Registration Practice Resolution of 2007 as elaborated in the Legal Subcommittee of UNCOPUOS, the Committee for the Peaceful Use of Outer Space. In this context an UNOOSA Registration Information

  11. Magnetic properties of sheet silicates

    International Nuclear Information System (INIS)

    Ballet, O.; Coey, J.M.D.

    1982-01-01

    Susceptibility, magnetisation and Moessbauer measurements are reported for a representative selection of 2:1 layer phyllosilicates. Eight samples from the mica, vermiculite and smectite groups include examples diluted in iron which are paramagnetic at all temperatures, as well as iron-rich silicates which order magnetically below 10 K. Anisotropic susceptibility of crystals of muscovite, biotite and vermiculite is quantitatively explained with a model where the Fe 2+ ions lie in sites of effective trigonal symmetry, the trigonal axis lying normal to the sheets. The ferrous ground state is an orbital singlet. Ferric iron gives an isotropic contribution to the susceptibility. Fe 2+ -Fe 2+ exchange interactions are ferromagnetic with Gapprox. equal to2 K, whereas Fe 3+ -Fe 3+ coupling is antiferromagnetic in the purely ferric minerals. A positive paramagnetic Curie temperature for glauconite may be attributable to Fe 2+ → Fe 3+ charge transfer. Magnetic order was found to set in inhomogeneously for glauconite at 1-7 K. One biotite sample showed an antiferromagnetic transition at Tsub(N) = 7 K marked by a well-defined susceptibility maximum. Its magnetic structure, consisting of ferromagnetic sheets with moments in their planes coupled antiferromagnetically by other, weak interactions, resembles that found earlier for the 1:1 mineral greenalite. (orig.)

  12. Weld Repair of Thin Aluminum Sheet

    Science.gov (United States)

    Beuyukian, C. S.; Mitchell, M. J.

    1986-01-01

    Weld repairing of thin aluminum sheets now possible, using niobium shield and copper heat sinks. Refractory niobium shield protects aluminum adjacent to hole, while copper heat sinks help conduct heat away from repair site. Technique limits tungsten/inert-gas (TIG) welding bombardment zone to melt area, leaving surrounding areas around weld unaffected. Used successfully to repair aluminum cold plates on Space Shuttle, Commercial applications, especially in sealing fractures, dents, and holes in thin aluminum face sheets or clad brazing sheet in cold plates, heat exchangers, coolers, and Solar panels. While particularly suited to thin aluminum sheet, this process also used in thicker aluminum material to prevent surface damage near weld area.

  13. Predicting Pulsar Scintillation from Refractive Plasma Sheets

    Science.gov (United States)

    Simard, Dana; Pen, Ue-Li

    2018-05-01

    The dynamic and secondary spectra of many pulsars show evidence for long-lived, aligned images of the pulsar that are stationary on a thin scattering sheet. One explanation for this phenomenon considers the effects of wave crests along sheets in the ionized interstellar medium, such as those due to Alfvén waves propagating along current sheets. If these sheets are closely aligned to our line-of-sight to the pulsar, high bending angles arise at the wave crests and a selection effect causes alignment of images produced at different crests, similar to grazing reflection off of a lake. Using geometric optics, we develop a simple parameterized model of these corrugated sheets that can be constrained with a single observation and that makes observable predictions for variations in the scintillation of the pulsar over time and frequency. This model reveals qualitative differences between lensing from overdense and underdense corrugated sheets: Only if the sheet is overdense compared to the surrounding interstellar medium can the lensed images be brighter than the line-of-sight image to the pulsar, and the faint lensed images are closer to the pulsar at higher frequencies if the sheet is underdense, but at lower frequencies if the sheet is overdense.

  14. Assessing the formability of metallic sheets by means of localized and diffuse necking models

    Science.gov (United States)

    Comşa, Dan-Sorin; Lǎzǎrescu, Lucian; Banabic, Dorel

    2016-10-01

    The main objective of the paper consists in elaborating a unified framework that allows the theoretical assessment of sheet metal formability. Hill's localized necking model and the Extended Maximum Force Criterion proposed by Mattiasson, Sigvant, and Larsson have been selected for this purpose. Both models are thoroughly described together with their solution procedures. A comparison of the theoretical predictions with experimental data referring to the formability of a DP600 steel sheet is also presented by the authors.

  15. Are safety data sheets for cleaning products used in Norway a factor contributing to the risk of workers exposure to chemicals?

    Directory of Open Access Journals (Sweden)

    Abdulqadir M. Suleiman

    2014-10-01

    Full Text Available Objectives: Cleaning products are considered less hazardous than those used in other sectors. Suppliers and distributors are less conscientious when it comes to informing users on health risks. The aim of the study was to elaborate on the usefulness and clarity of information in the safety data sheets (SDS for cleaning products, and considering if the use of these SDSs can be seen as a risk factor towards occupational exposure to hazardous chemicals in the sector. Material and Methods: Safety data sheets were selected based on the risk level of the product assigned in an industrial sector scheme. 320 SDSs for cleaning products were reviewed. Constituent components found in the products over a given threshold were listed and available information thereof used to assess the perceived non-hazard consideration of the chemicals. Results: The contents of the SDSs was generic and mostly incomplete. Safety measures and health information lacked sufficient specificity despite varying compositions and concentrations of components. There is generally incompatibility between mentioned sections on the suggested non-hazardous nature of the products and health effects. Not all substances used in these products have harmonized classifications, which makes them open to various classification of the products and the suggested safety measures. This results in different companies classifying similar products differently. Risk management measures and suggested personal protective equipment (PPEs are given haphazardly. Physical properties relevant to risk assessment are not included. Conclusions: The safety data sheets are ambiguous, and they lack relevant and important information. Inadequate information and risk assessment concerning the products can lead to workers being exposed to hazardous chemicals. Underestimation of the hazard contribution of the components of the products and the insufficient, non-objective mention of appropriate control and protective

  16. Catalogue of X-Ray Texture Data for Al-Cu-Li Alloy 1460, 2090, 2096 and 2195 Near-Net-Shape Extrusions, Sheet and Plate

    Science.gov (United States)

    Hales, Stephen J.; Hafley, Robert A.; Alexa, Joel A.

    1998-01-01

    The effect of crystallographic texture on the mechanical properties of near-net-shape extrusions is of major interest ff these products are to find application in launch vehicle or aircraft structures. The objective of this research was to produce a catalogue containing quantitative texture information for extruded product, sheet and plate. The material characterized was extracted from wide, integrally stiffened panels fabricated from the Al-Cu-Li alloys 1460, 2090, 2096 and 2195. The textural characteristics of sheet and plate products of the same alloys were determined for comparison purposes. The approach involved using X-ray diffraction to generate pole figures in combination with orientation distribution function analysis. The data were compiled as a function of location in the extruded cross-sections and the variation in the major deformation- and recrystallization-related texture components was identified.

  17. Characterization of double face adhesive sheets for ceramic tile installation

    International Nuclear Information System (INIS)

    Nascimento, Otavio L.; Mansur, Alexandra A.P.; Mansur, Herman S.

    2011-01-01

    The main goal of this work was the characterization of an innovative ceramic tile installation product based on double face adhesive sheets. Density, hardness, tensile strength, x-ray diffraction, infrared spectroscopy, and scanning electron microscopy coupled with spectroscopy of dispersive energy assays were conducted. The results are in agreement with some manufacture specifications and the obtained information will be crucial in the analysis of durability and stability of the ceramic tile system installed with this new product. (author)

  18. Buckling of Aluminium Sheet Components

    Science.gov (United States)

    Hegadekatte, Vishwanath; Shi, Yihai; Nardini, Dubravko

    Wrinkling is one of the major defects in sheet metal forming processes. It may become a serious obstacle to implementing the forming process and assembling the parts, and may also play a significant role in the wear of the tool. Wrinkling is essentially a local buckling phenomenon that results from compressive stresses (compressive instability) e.g., in the hoop direction for axi-symmetric systems such as beverage cans. Modern beverage can is a highly engineered product with a complex geometry. Therefore in order to understand wrinkling in such a complex system, we have started by studying wrinkling with the Yoshida buckling test. Further, we have studied the buckling of ideal and dented beverage cans under axial loading by laboratory testing. We have modelled the laboratory tests and also the imperfection sensitivity of the two systems using finite element method and the predictions are in qualitative agreement with experimental data.

  19. RAMS+C informed decision-making with application to multi-objective optimization of technical specifications and maintenance using genetic algorithms

    International Nuclear Information System (INIS)

    Martorell, S.; Villanueva, J.F.; Carlos, S.; Nebot, Y.; Sanchez, A.; Pitarch, J.L.; Serradell, V.

    2005-01-01

    The role of technical specifications and maintenance (TSM) activities at nuclear power plants (NPP) aims to increase reliability, availability and maintainability (RAM) of Safety-Related Equipment, which, in turn, must yield to an improved level of plant safety. However, more resources (e.g. costs, task force, etc.) have to be assigned in above areas to achieve better scores in reliability, availability, maintainability and safety (RAMS). Current situation at NPP shows different programs implemented at the plant that aim to the improvement of particular TSM-related parameters where the decision-making process is based on the assessment of the impact of the change proposed on a subgroup of RAMS+C attributes. This paper briefly reviews the role of TSM and two main groups of improvement programs at NPP, which suggest the convenience of considering the approach proposed in this paper for the Integrated Multi-Criteria Decision-Making on changes to TSM-related parameters based on RAMS+C criteria as a whole, as it can be seem as a decision-making process more consistent with the role and synergic effects of TSM and the objectives and goals of current improvement programs at NPP. The case of application to the Emergency Diesel Generator system demonstrates the viability and significance of the proposed approach for the Multi-objective Optimization of TSM-related parameters using a Genetic Algorithm

  20. 46 CFR 232.4 - Balance sheet accounts.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false Balance sheet accounts. 232.4 Section 232.4 Shipping... ACTIVITIES UNIFORM FINANCIAL REPORTING REQUIREMENTS Balance Sheet § 232.4 Balance sheet accounts. (a.... (b) Purpose of balance sheet accounts. The balance sheet accounts are intended to disclose the...

  1. THE MODEL OF DISTINCTION OF ACCESS RIGHTS TO INFORMATION OBJECTS OF THE SYSTEM OF CONTROLLING OF BUSINESS PROCESSES OF AN AVIATION ENTERPRISE

    Directory of Open Access Journals (Sweden)

    Andrey V. Degtyarev

    2014-01-01

    Full Text Available On the basis of the analysis of controlling system of business processes ofaviation enterprise was formulated the approach for set up an hierarchicalmodel of personal permissions to information resources of an automatic of thesystem of controlling of projects and contracts (ASCPC on the instrumentaland procedure levels. On the model base structure of personalized key wasdeveloped. This model reflective of possibilities of the every category of userswhen working with ASCPC.

  2. Nuclear Energy General Objectives

    International Nuclear Information System (INIS)

    2011-01-01

    One of the IAEA's statutory objectives is to 'seek to accelerate and enlarge the contribution of atomic energy to peace, health and prosperity throughout the world'. One way it achieves this objective is to issue publications in various series. Two of these series are the IAEA Nuclear Energy Series and the IAEA Safety Standards Series. According to Article III, paragraph A.6, of the IAEA Statute, the IAEA safety standards establish 'standards of safety for protection of health and minimization of danger to life and property.' The safety standards include the Safety Fundamentals, Safety Requirements and Safety Guides. These standards are primarily written in a regulatory style, and are binding on the IAEA for its own activities. The principal users are Member State regulatory bodies and other national authorities. The IAEA Nuclear Energy Series consists of reports designed to encourage and assist research on, and development and practical application of, nuclear energy for peaceful uses. This includes practical examples to be used by owners and operators of utilities in Member States, implementing organizations, academia and politicians, among others. The information is presented in guides, reports on the status of technology and advances, and best practices for peaceful uses of nuclear energy based on inputs from international experts. The series complements the IAEA's safety standards, and provides detailed guidance, experience, good practices and examples on the five areas covered in the IAEA Nuclear Energy Series. The Nuclear Energy Basic Principles is the highest level publication in the IAEA Nuclear Energy Series and describes the rationale and vision for the peaceful uses of nuclear energy. It presents eight Basic Principles on which nuclear energy systems should be based to fulfil nuclear energy's potential to help meet growing global energy needs. The Nuclear Energy Series Objectives are the second level publications. They describe what needs to be

  3. Prediction of formability of aluminum alloy 5454 sheet

    International Nuclear Information System (INIS)

    Kim, Chan Il; Yang, Seung Han; Kim, Young Suk

    2012-01-01

    In the automobile industry, reducing the weight is the most important objective for reducing air pollution and improving the fuel efficiency. For this reason, the application of aluminum sheets is increasing. When the sheets are applied to the automobile, using inappropriate variables for the material, product design, and press processing can generate tearing, wrinkling, and spring back problems, which are the main types of failure in the manufacturing process. Therefore, it is necessary to reduce these failures by harmonizing the many variables and strictly managing the processes. In this research, we study the theoretical plasticity instability of Al5454 and obtain the forming limit diagram (FLD) using MATLAB. Moreover, we compare the theoretical FLD with an experimental FLD obtained from a stretching test

  4. Protein structure predictions with Monte Carlo simulated annealing: Case for the β-sheet

    Science.gov (United States)

    Okamoto, Y.; Fukugita, M.; Kawai, H.; Nakazawa, T.

    Work is continued for a prediction of three-dimensional structure of peptides and proteins with Monte Carlo simulated annealing using only a generic energy function and amino acid sequence as input. We report that β-sheet like structure is successfully predicted for a fragment of bovine pancreatic trypsin inhibitor which is known to have the β-sheet structure in nature. Together with the results for α-helix structure reported earlier, this means that a successful prediction can be made, at least at a qualitative level, for two dominant building blocks of proteins, α-helix and β-sheet, from the information of amino acid sequence alone.

  5. Study on antioxidant experiment on forged steel tube sheet and tube hole for steam generator

    International Nuclear Information System (INIS)

    Zong Hai; Wang Detai; Ding Yang

    2012-01-01

    Antioxidant experiment on forged steel tube sheet and tube hole for steam generator was studied and the influence of different simulated heat treatments on the antioxidant performance of tube sheet and tube hole was made. The influence of different antioxidant methods on the size of tube hole was drawn. Furthermore, the change of size and weight of 18MnD5 forged steel tube sheet on the condition of different simulated heat treatments was also studied. The analytical results have proved reference information for the use of 18MnD5 material and for key processes of processing tube hole and wearing and expanding U-style tube. (authors)

  6. Fact Sheets on Pesticides in Schools.

    Science.gov (United States)

    National Coalition against the Misuse of Pesticides, Washington, DC.

    This document consists of a collection of fact sheets about the use of pesticides in schools and how to reduce it. The sheets are: (1) "Alternatives to Using Pesticides in Schools: What Is Integrated Pest Management?"; (2) "Health Effects of 48 Commonly Used Pesticides in Schools"; (3) "The Schooling of State Pesticide…

  7. Balance velocities of the Greenland ice sheet

    DEFF Research Database (Denmark)

    Joughin, I.; Fahnestock, M.; Ekholm, Simon

    1997-01-01

    We present a map of balance velocities for the Greenland ice sheet. The resolution of the underlying DEM, which was derived primarily from radar altimetery data, yields far greater detail than earlier balance velocity estimates for Greenland. The velocity contours reveal in striking detail......, the balance map is useful for ice-sheet modelling, mass balance studies, and field planning....

  8. Advanced friction modeling for sheet metal forming

    NARCIS (Netherlands)

    Hol, J.; Cid Alfaro, M.V.; de Rooij, Matthias B.; Meinders, Vincent T.

    2012-01-01

    The Coulomb friction model is frequently used for sheet metal forming simulations. This model incorporates a constant coefficient of friction and does not take the influence of important parameters such as contact pressure or deformation of the sheet material into account. This article presents a

  9. Advanced friction modeling in sheet metal forming

    NARCIS (Netherlands)

    Hol, J.; Cid Alfaro, M.V.; Meinders, Vincent T.; Huetink, Han

    2011-01-01

    The Coulomb friction model is frequently used for sheet metal forming simulations. This model incorporates a constant coefficient of friction and does not take the influence of important parameters such as contact pressure or deformation of the sheet material into account. This article presents a

  10. Antibubbles and fine cylindrical sheets of air

    NARCIS (Netherlands)

    Beilharz, D.; Guyon, A.; Li, E.Q.; Thoraval, Marie-Jean; Thoroddsen, S.T.

    2015-01-01

    Drops impacting at low velocities onto a pool surface can stretch out thin hemispherical sheets of air between the drop and the pool. These air sheets can remain intact until they reach submicron thicknesses, at which point they rupture to form a myriad of microbubbles. By impacting a

  11. Molding cork sheets to complex shapes

    Science.gov (United States)

    Sharpe, M. H.; Simpson, W. G.; Walker, H. M.

    1977-01-01

    Partially cured cork sheet is easily formed to complex shapes and then final-cured. Temperature and pressure levels required for process depend upon resin system used and final density and strength desired. Sheet can be bonded to surface during final cure, or can be first-formed in mold and bonded to surface in separate step.

  12. Fuels planning: science synthesis and integration; social issues fact sheet 03: Developing personal responsibility for fuels reduction: More ways to catch and hold people's attention

    Science.gov (United States)

    Rocky Mountain Research Station USDA Forest Service

    2004-01-01

    Other fact sheets discuss the different types of information that are useful in explaining to property owners the importance of taking personal responsibility for fuels management on their land. However, for some property owners, new information is not enough-they may need more information in order to understand that change is necessary. This fact sheet discusses ways...

  13. Pressure balance between lobe and plasma sheet

    International Nuclear Information System (INIS)

    Baumjohann, W.; Paschmann, G.; Luehr, H.

    1990-01-01

    Using eight months of AMPTE/IRM plasma and magnetic field data, the authors have done a statistical survey on the balance of total (thermal and magnetic) pressure in the Earth's plasma sheet and tail lobe. About 300,000 measurements obtained in the plasma sheet and the lobe were compared for different levels of magnetic activity as well as different distances from the Earth. The data show that lobe and plasma sheet pressure balance very well. Even in the worst case they do not deviate by more than half of the variance in the data itself. Approximately constant total pressure was also seen during a quiet time pass when IRM traversed nearly the whole magnetotail in the vertical direction, from the southern hemisphere lobe through the neutral sheet and into the northern plasma sheet boundary layer

  14. Fact Sheets and Questions and Answers for the Final Air Toxics Rules for the Aerospace Manufacturing and Rework Industry

    Science.gov (United States)

    This page contains the July 1995 final rule fact sheet and the January 2015 proposed rule fact sheet that contains information on the National Emission Standards for Aerospace Manufacturing and Rework Facilities, as well as a 2001 Q&A document on the rule

  15. COMPARISON OF VARIOUS APPROACHES TO MULTI-CHANNEL INFORMATION FUSION IN C-OTDR SYSTEMS FOR REMOTE MONITORING OF EXTENDED OBJECTS

    Directory of Open Access Journals (Sweden)

    A. V. Timofeev

    2015-01-01

    Full Text Available The paper presents new results concerning selection of optimal information fusion formula for ensembles of COTDR channels. Here C-OTDR is a coherent optical time domain reflectometer. Each of these channels provides data for appropriate automatic classifier which is designed to classify the elastic vibration sources in the multiclass case. Those classifiers form a so-called classifiers ensemble. Ensembles of Lipschitz Classifiers were considered. In this case the goal of information fusion is to create an integral classificator designed for effective classification of seismoacoustic target events. The Matching Pursuit Optimization Ensemble Classifiers (MPOEC, the Linear Programming Boosting (LP-Boost (LP-β and LP-B variants, the Multiple Kernel Learning (MKL, and Weighing of Inversely as Lipschitz Constants (WILC approaches were compared. The WILC is a brand new approach to optimal fusion of Lipschitz Classifiers Ensembles. The basics of these methods have been briefly described along with intrinsic features. All of those methods are based on reducing the task of choosing convex hull parameters to a solution of an optimization problem. All of the mentioned approaches can be successfully used for using in the C-OTDR system data processing. Results of practical usage are presented.

  16. Folded Sheet Versus Transparent Sheet Models for Human Symmetry Judgments

    Directory of Open Access Journals (Sweden)

    Jacques Ninio

    2011-07-01

    Full Text Available As a contribution to the mysteries of human symmetry perception, reaction time data were collected on the detection of symmetry or repetition violations, in the context of short term visual memory studies. The histograms for reaction time distributions are rather narrow in the case of symmetry judgments. Their analysis was performed in terms of a simple kinetic model of a mental process in two steps, a slow one for the construction of the representation of the images to be compared, and a fast one, in the 50 ms range, for the decision. There was no need for an additional ‘mental rotation’ step. Symmetry seems to facilitate the construction step. I also present here original stimuli showing a color equalization effect across a symmetry axis, and its counterpart in periodic patterns. According to a “folded sheet model”, when a shape is perceived, the brain automatically constructs a mirror-image representation of the shape. Based in part on the reaction time analysis, I present here an alternative “transparent sheet” model in which the brain constructs a single representation, which can be accessed from two sides, thus generating simultaneously a pattern and its mirror-symmetric partner. Filtering processes, implied by current models of symmetry perception could intervene at an early stage, by nucleating the propagation of similar perceptual groupings in the two symmetric images.

  17. Strain and mechanical properties of the VCM multilayer sheet and their composites using the digital speckle correlation method.

    Science.gov (United States)

    Zhang, Dehai; Xie, Guizhong; Li, Yanqin; Liu, Jianxiu

    2015-09-01

    The digital speckle correlation method (DSCM) is introduced to solve the challenging problems in the related geometric measurement. Theoretical calculations of strain are deduced using the DSCM. Corresponding strains along x and y directions are obtained from uniaxial tension experiments and digital speckle measurements, using the VCM nondeep drawing multilayer sheet, the VCM deep-drawing multilayer sheet, clad films, nondeep drawing substrate, and deep-drawing substrate sheet as the targeted experimental objects. The results show that the maximum strains along the x direction of the VCM nondeep drawing multilayer sheet, the VCM deep-drawing multilayer sheet, clad film, nondeep drawing substrate, and deep-drawing substrate sheet are 68.473%, 48.632%, 91.632%, 50.784% and 40.068%, respectively, while the maximum strains along the y direction are -2.657%, -15.381%, 2.826%, -9.780% and -7.783%, respectively. The mechanical properties of the VCM multilayer sheet are between those of the substrate and clad film, while mechanical properties of the VCM deep-drawing multilayer sheet are superior to those of the VCM nondeep drawing multi-layer sheet.

  18. Magnetic reconnection and current sheet formation in 3D magnetic configurations

    International Nuclear Information System (INIS)

    Frank, A.G.

    1999-01-01

    The problem of magnetic reconnection in three-dimensional (3D) magnetic configurations has been studied experimentally. The research has concentrated on the possibilities of formation of current sheets, which represent crucial objects for a realization of magnetic reconnection phenomena. Different types of 3D magnetic configurations were examined, including configurations with singular lines of the X-type, non-uniform fields containing isolated magnetic null-points and without null-points. It was revealed that formation of quasi-one-dimensional current sheets is the universal process for plasma dynamics in 3D magnetic fields both with null-points and without. At the same time the peculiarities of current sheets, plasma dynamics and magnetic reconnection processes depend essentially on characteristics of 3D magnetic configurations. The result of principal significance obtained was that magnetic reconnection phenomena can take place in a wide range of 3D magnetic configurations as a consequence of their ability to form current sheets. (author)

  19. Learning Objects Web

    DEFF Research Database (Denmark)

    Blåbjerg, Niels Jørgen

    2005-01-01

    Learning Objects Web er et DEFF projekt som Aalborg Universitetsbibliotek har initieret. Projektet tager afsæt i de resultater og erfaringer som er opnået med vores tidligere projekt Streaming Webbased Information Modules (SWIM). Vi har et internationalt netværk af interessenter som giver os...... sparring og feedback i forhold til udviklingskoncept både omkring de teoretiske rammer og i forhold til praktisk anvendelse af vores undervisningskoncept. Med disse rygstød og input har vi forfulgt ønsket om at videreudvikle SWIM i det nye projekt Learning Objects Web. Udgivelsesdato: juni...

  20. Communicating the balance sheet in breast cancer screening.

    Science.gov (United States)

    Giordano, Livia; Cogo, Carla; Patnick, Julietta; Paci, Eugenio

    2012-01-01

    Despite the difficulties, there is a moral responsibility to provide the public with the best estimates of benefits and harms of breast cancer screening. In this paper we review the issues in communication of benefits and harms of medical interventions and discuss these in terms of the principles of the balance sheet proposed in this supplement. The balance sheet can be seen as a tool to convey estimates based on the best available evidence and addressed to a readership wider than just potential screening participants. It reflects a re-assessment of screening efficacy, showing again that screening is effective and brings more benefits than harms. It can be viewed as an opportunity to re-affirm some basic principles of good evidence-based communication. Further research is needed to improve communication strategy, to assess the impact of this communication on women's awareness and to evaluate its utility in the informed decision-making process. The balance sheet could be a starting point for a broader vision of informed decision-making in screening, which should also recognize the role played by 'non-numerical' factors on women's choice of participating in breast cancer screening.

  1. Rupture of nanoscaled water sheets in the presence of an applied electric field

    Energy Technology Data Exchange (ETDEWEB)

    Gopan, Nandu, E-mail: nandug@jncasr.ac.in [Engineering Mechanics Unit, Jawaharlal Nehru Centre for Advanced Scientific Research, Jakkur, Bangalore-560 064 (India)

    2016-12-15

    Understanding the behaviour of water sheets is relevant in numerous areas, such as thin film coating and atomisation. The rupture of planar liquid sheets are interesting due to the fact that they are objects of co-dimension 1. Previous work seems to suggest that a generic route to liquid structure fragmentation is via liquid sheets. The interplay between inertia, surface tension and viscosity is crucial in determining the dynamics of liquid sheets at a macro scale. At the nanoscale, where thermal fluctuations are expected to play a dominant role, the dynamics become more interesting. The stability and rupture dynamics of nanoscaled water sheets, at constant temperature, are studied using constrained molecular dynamics (MD) simulations. The SPC/E potential with long range electrostatics is used to simulate water molecules. The effect of an applied electric field on the stability of the nanoscaled water sheet forms the focus of this study. The effect of the initial configuration is studied by changing the random seed values used for velocity initialisation. The effect of sheet thickness on the rupture dynamics is also explored. It is seen that when large electric fields (5 V/nm) act across very thin sheets (1 layer), then breakup into multiple ellipsoidal structures is a possibility, and the response of the fluid structure to the applied electric field is non-linear. Furthermore, it is seen that Taylor's predictions for the critical electric field intensity, based on classical electro-hydrodynamics for the onset of instability in macroscopic drops, scales surprisingly well for the case of nanoscaled sheets. (paper)

  2. Tube sheet design for PFBR steam generator

    International Nuclear Information System (INIS)

    Chellapandi, P.; Chetal, S.C.; Bhoje, S.B.

    1991-01-01

    Top and bottom tube sheets of PFBR Steam Generators have been analysed with 3D and axisymmetric models using CASTEM Programs. Analysis indicates that the effects of piping reactions at the inlet/outlet nozzles on the primary stresses in the tube sheets are negligible and the asymmetricity of the deformation pattern introduced in the tube sheet by the presence of inlet/outlet and manhole nozzles is insignificant. The minimum tube sheet thicknesses for evaporator and reheater are 135 mm and 75 mm respectively. Further analysis has indicated the minimum fillet radius at the junction of tube sheet and dished end should be 20 mm. Simplified methodology has been developed to arrive at the number of thermal baffles required to protect the tube sheet against fatigue damage due to thermal transient. This method has been applied to PFBR steam generators to determine the required number of thermal baffles. For protecting the bottom tube sheet of evaporator against the thermal shock due to feed water and secondary pump trip, one thermal shield is found to be sufficient. Further analysis is required to decide upon the actual number to take care of the severe thermal transient, following the event of sudden dumping of water/steam, immediately after the sodium-water reaction. (author)

  3. Investigations of the form and flow of ice sheets and glaciers using radio-echo sounding

    Energy Technology Data Exchange (ETDEWEB)

    Dowdeswell, J A; Evans, S [Scott Polar Research Institute, University of Cambridge, Cambridge CB2 1ER (United Kingdom)

    2004-10-01

    Radio-echo sounding (RES), utilizing a variety of radio frequencies, was developed to allow glaciologists to measure the thickness of ice sheets and glaciers. We review the nature of electromagnetic wave propagation in ice and snow, including the permittivity of ice, signal attenuation and volume scattering, along with reflection from rough and specular surfaces. The variety of instruments used in RES of polar ice sheets and temperate glaciers is discussed. The applications and insights that a knowledge of ice thickness, and the wider nature of the form and flow of ice sheets, provides are also considered. The thickest ice measured is 4.7 km in East Antarctica. The morphology of the Antarctic and Greenland ice sheets, and many of the smaller ice caps and glaciers of the polar regions, has been investigated using RES. These findings are being used in three-dimensional numerical models of the response of the cryosphere to environmental change. In addition, the distribution and character of internal and basal reflectors within ice sheets contains information on, for example, ice-sheet layering and its chrono-stratigraphic significance, and has enabled the discovery and investigation of large lakes beneath the Antarctic Ice Sheet. Today, RES from ground-based and airborne platforms remains the most effective tool for measuring ice thickness and internal character.

  4. Thermomechanical processing of plasma sprayed intermetallic sheets

    Science.gov (United States)

    Hajaligol, Mohammad R.; Scorey, Clive; Sikka, Vinod K.; Deevi, Seetharama C.; Fleischhauer, Grier; Lilly, Jr., A. Clifton; German, Randall M.

    2001-01-01

    A powder metallurgical process of preparing a sheet from a powder having an intermetallic alloy composition such as an iron, nickel or titanium aluminide. The sheet can be manufactured into electrical resistance heating elements having improved room temperature ductility, electrical resistivity, cyclic fatigue resistance, high temperature oxidation resistance, low and high temperature strength, and/or resistance to high temperature sagging. The iron aluminide has an entirely ferritic microstructure which is free of austenite and can include, in weight %, 4 to 32% Al, and optional additions such as .ltoreq.1% Cr, .gtoreq.0.05% Zr .ltoreq.2% Ti, .ltoreq.2% Mo, .ltoreq.1% Ni, .ltoreq.0.75% C, .ltoreq.0.1% B, .ltoreq.1% submicron oxide particles and/or electrically insulating or electrically conductive covalent ceramic particles, .ltoreq.1% rare earth metal, and/or .ltoreq.3% Cu. The process includes forming a non-densified metal sheet by consolidating a powder having an intermetallic alloy composition such as by roll compaction, tape casting or plasma spraying, forming a cold rolled sheet by cold rolling the non-densified metal sheet so as to increase the density and reduce the thickness thereof and annealing the cold rolled sheet. The powder can be a water, polymer or gas atomized powder which is subjecting to sieving and/or blending with a binder prior to the consolidation step. After the consolidation step, the sheet can be partially sintered. The cold rolling and/or annealing steps can be repeated to achieve the desired sheet thickness and properties. The annealing can be carried out in a vacuum furnace with a vacuum or inert atmosphere. During final annealing, the cold rolled sheet recrystallizes to an average grain size of about 10 to 30 .mu.m. Final stress relief annealing can be carried out in the B2 phase temperature range.

  5. Product Disclosure Sheet of Islamic Bank in Malaysia: Home Financing

    Directory of Open Access Journals (Sweden)

    Muhammad Fakhirin, C. M.

    2016-12-01

    Full Text Available The diversity of financial products offered by the financial service providers along with the upwards trend of home financing in Malaysia has significant relationship with information disclosure about the products. Consistency in disclosing essential information is aimed at minimizing the mis-selling of financial products to avoid gharar (ambiguity. Therefore, the purpose of this study is to highlight the practice of disclosing information of the home financing products by five major commercial banks in Malaysia which are Maybank Islamic Berhad, CIMB Islamic Bank Berhad, Bank Islam Malaysia Berhad, Public Islamic Bank Berhad, and AmIslamic Bank Berhad. The study employs qualitative method whereby secondary data were gathered from selected Islamic Financial Institutions (IFIs websites. It reports the evaluation of the types of information which have been disclosed in the Product Disclosure Sheet of each product and the comparison between all five banks. Data gathered were analysed using frequencies via SPSS version 20. The findings show that four out of five banks have published the Product Disclosure Sheets (PDSs in their respective websites. The types of information disclosed by all banks slightly vary from each other. However, AmIslamic Bank Berhad appears to be a highly disclosed institution that relates to home financing facility, while Bank Islam Malaysia Berhad disclosed the least information in the PDSs. Besides, CIMB Islamic Bank Berhad is the only bank which did not make the PDSs available in their website.

  6. Plasma sheet behavior during substorms

    International Nuclear Information System (INIS)

    Hones, E.W. Jr.

    1983-01-01

    Auroral or magnetic substorms are periods of enhanced auroral and geomagnetic activity lasting one to a few hours that signify increased dissipation of energy from the magnetosphere to the earth. Data acquired during the past decade from satellites in the near-earth sector of the magnetotail have suggested that during a substorm part of the plasma sheet is severed from earth by magnetic reconnection, forming a plasmoid, i.e., a body of plasma and closed magnetic loops, that flows out of the tail into the solar wind, thus returning plasma and energy that have earlier been accumulated from the solar wind. Very recently this picture has been dramatically confirmed by observations, with the ISEE 3 spacecraft in the magnetotail 220 R/sub E/ from earth, of plasmoids passing that location in clear delayed response to substorms. It now appears that plasmoid release is a fundamental process whereby the magnetosphere gives up excess stored energy and plasma, much like comets are seen to do, and that the phenomena of the substorm seen at earth are a by-product of that fundamental process

  7. Radiation dominated relativistic current sheets

    International Nuclear Information System (INIS)

    Jaroschek, C.H.

    2008-01-01

    Relativistic Current Sheets (RCS) feature plasma instabilities considered as potential key to magnetic energy dissipation and non-thermal particle generation in Poynting flux dominated plasma flows. We show in a series of kinetic plasma simulations that the physical nature of non-linear RCS evolution changes in the presence of incoherent radiation losses: In the ultra-relativistic regime (i.e. magnetization parameter sigma = 104 defined as the ratio of magnetic to plasma rest frame energy density) the combination of non-linear RCS dynamics and synchrotron emission introduces a temperature anisotropy triggering the growth of the Relativistic Tearing Mode (RTM). As direct consequence the RTM prevails over the Relativistic Drift Kink (RDK) Mode as competitive RCS instability. This is in contrast to the previously studied situation of weakly relativistic RCS (sigma ∼ 1) where the RDK is dominant and most of the plasma is thermalized. The simulations witness the typical life cycle of ultra-relativistic RCS evolving from a violent radiation induced collapse towards a radiation quiescent state in rather classical Sweet-Parker topology. Such a transition towards Sweet-Parker configuration in the late non-linear evolution has immediate consequences for the efficiency of magnetic energy dissipation and non-thermal particle generation. Ceasing dissipation rates directly affect our present understanding of non-linear RCS evolution in conventional striped wind scenarios. (author)

  8. World-sheet gauge fields in superstrings

    International Nuclear Information System (INIS)

    Porrati, M.; Tomboulis, E.T.

    1989-01-01

    We investigate the introduction of world-sheet 2-dimensional gauge fields in a manner consistent with world-sheet supersymmetry. We obtain the effective string action resulting from the exact integration over the world-sheet gauge fields to show that it generally describes string models with spontaneous breaking of gauge symmetries with continuous breaking parameters. We examine the question of spacetime supersymmetry spontaneous breaking, and show that breaking with continuous, in particular arbitrarily small breaking parameters does not occur; only breaking for discrete values of parameters is possible. (orig.)

  9. Bifurcation of Jovian magnetotail current sheet

    Directory of Open Access Journals (Sweden)

    P. L. Israelevich

    2006-07-01

    Full Text Available Multiple crossings of the magnetotail current sheet by a single spacecraft give the possibility to distinguish between two types of electric current density distribution: single-peaked (Harris type current layer and double-peaked (bifurcated current sheet. Magnetic field measurements in the Jovian magnetic tail by Voyager-2 reveal bifurcation of the tail current sheet. The electric current density possesses a minimum at the point of the Bx-component reversal and two maxima at the distance where the magnetic field strength reaches 50% of its value in the tail lobe.

  10. Bifurcation of Jovian magnetotail current sheet

    Directory of Open Access Journals (Sweden)

    P. L. Israelevich

    2006-07-01

    Full Text Available Multiple crossings of the magnetotail current sheet by a single spacecraft give the possibility to distinguish between two types of electric current density distribution: single-peaked (Harris type current layer and double-peaked (bifurcated current sheet. Magnetic field measurements in the Jovian magnetic tail by Voyager-2 reveal bifurcation of the tail current sheet. The electric current density possesses a minimum at the point of the Bx-component reversal and two maxima at the distance where the magnetic field strength reaches 50% of its value in the tail lobe.

  11. 3D-PRINTING OF BUILD OBJECTS

    Directory of Open Access Journals (Sweden)

    SAVYTSKYI M. V.

    2016-03-01

    Full Text Available Raising of problem. Today, in all spheres of our life we can constate the permanent search for new, modern methods and technologies that meet the principles of sustainable development. New approaches need to be, on the one hand more effective in terms of conservation of exhaustible resources of our planet, have minimal impact on the environment and on the other hand to ensure a higher quality of the final product. Construction is not exception. One of the new promising technology is the technology of 3D -printing of individual structures and buildings in general. 3Dprinting - is the process of real object recreating on the model of 3D. Unlike conventional printer which prints information on a sheet of paper, 3D-printer allows you to display three-dimensional information, i.e. creates certain physical objects. Currently, 3D-printer finds its application in many areas of production: machine building elements, a variety of layouts, interior elements, various items. But due to the fact that this technology is fairly new, it requires the creation of detailed and accurate technologies, efficient equipment and materials, and development of common vocabulary and regulatory framework in this field. Research Aim. The analysis of existing methods of creating physical objects using 3D-printing and the improvement of technology and equipment for the printing of buildings and structures. Conclusion. 3D-printers building is a new generation of equipment for the construction of buildings, structures, and structural elements. A variety of building printing technics opens up wide range of opportunities in the construction industry. At this stage, printers design allows to create low-rise buildings of different configurations with different mortars. The scientific novelty of this work is to develop proposals to improve the thermal insulation properties of constructed 3D-printing objects and technological equipment. The list of key terms and notions of construction

  12. RAPID FREEFORM SHEET METAL FORMING: TECHNOLOGY DEVELOPMENT AND SYSTEM VERIFICATION

    Energy Technology Data Exchange (ETDEWEB)

    Kiridena, Vijitha [Ford Scientific Research Lab., Dearborn, MI (United States); Verma, Ravi [Boeing Research and Technology (BR& T), Seattle, WA (United States); Gutowski, Timothy [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Roth, John [Pennsylvania State Univ., University Park, PA (United States)

    2018-03-31

    The objective of this project is to develop a transformational RApid Freeform sheet metal Forming Technology (RAFFT) in an industrial environment, which has the potential to increase manufacturing energy efficiency up to ten times, at a fraction of the cost of conventional technologies. The RAFFT technology is a flexible and energy-efficient process that eliminates the need for having geometry-specific forming dies. The innovation lies in the idea of using the energy resource at the local deformation area which provides greater formability, process control, and process flexibility relative to traditional methods. Double-Sided Incremental Forming (DSIF), the core technology in RAFFT, is a new concept for sheet metal forming. A blank sheet is clamped around its periphery and gradually deformed into a complex 3D freeform part by two strategically aligned stylus-type tools that follow a pre-described toolpath. The two tools, one on each side of the blank, can form a part with sharp features for both concave and convex shapes. Since deformation happens locally, the forming force at any instant is significantly decreased when compared to traditional methods. The key advantages of DSIF are its high process flexibility, high energy-efficiency, low capital investment, and the elimination of the need for massive amounts of die casting and machining. Additionally, the enhanced formability and process flexibility of DSIF can open up design spaces and result in greater weight savings.

  13. Unraveling metamaterial properties in zigzag-base folded sheets.

    Science.gov (United States)

    Eidini, Maryam; Paulino, Glaucio H

    2015-09-01

    Creating complex spatial objects from a flat sheet of material using origami folding techniques has attracted attention in science and engineering. In the present work, we use the geometric properties of partially folded zigzag strips to better describe the kinematics of known zigzag/herringbone-base folded sheet metamaterials such as Miura-ori. Inspired by the kinematics of a one-degree of freedom zigzag strip, we introduce a class of cellular folded mechanical metamaterials comprising different scales of zigzag strips. This class of patterns combines origami folding techniques with kirigami. Using analytical and numerical models, we study the key mechanical properties of the folded materials. We show that our class of patterns, by expanding on the design space of Miura-ori, is appropriate for a wide range of applications from mechanical metamaterials to deployable structures at small and large scales. We further show that, depending on the geometry, these materials exhibit either negative or positive in-plane Poisson's ratios. By introducing a class of zigzag-base materials in the current study, we unify the concept of in-plane Poisson's ratio for similar materials in the literature and extend it to the class of zigzag-base folded sheet materials.

  14. Nuclear Data Sheets for A = 79

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Balraj

    2016-07-15

    Nuclear spectroscopic information for known nuclides of mass number 79 (Ni,Cu,Zn,Ga,Ge,As,Se,Br,Kr,Rb, Sr,Y,Zr) has been evaluated and presented together with adopted energies, Jπ, and decay modes of levels in these nuclei. No data are yet available for excited states in {sup 79}Ni, {sup 79}Cu and {sup 79}Zr. The half–life of {sup 79}Se, a nuclide of importance in reactor–irradiated fuel composition has been measured by several independent groups and reported in a number of publications after 1995, and seems to be converging to a narrow margin of experimental values. These measurements were likely prompted by a recommendation made in the 1993 update of A = 79 nuclides (1993Si28), that since a 1949PaZZ report, there had been no measurement until 1993, and that based on simulation studies by 1993HeZW, the value listed in 1949PaZZ, and cited in all data tables and charts for 44 years, was quite likely in error, being too low by a factor of 10. According to conclusions in recent papers such as 2014Do20, there is still room for improvement in the measurement of this half–life, and further experiments are expected. This evaluation supersedes earlier Nuclear Data Sheets for A = 79 (2002Si13,1993Si28, 1982Si21,1975Ur03).

  15. Method of making tomographic images of X-rayed objects

    International Nuclear Information System (INIS)

    Eickel, R.

    1979-01-01

    A tomographic image of a selected layer of a stationary object is made by moving the source of X-rays along a first path at one side of the selected layer and by moving an ionography imaging chamber which contains a dielectric receptor sheet along a second path at the other side of the selected layer. The movement of the sheet is synchronized with movement of the source of X-rays and includes a translatory movement in a direction counter to the direction of movement of the source, a pivotal movement to maintain the sheet in a plane which is normal to the central beam of the bundle of X-rays, and a sidewise movement to vary the distance between the selected layer and the sheet so that the length of the projection of selected layer upon the sheet remains unchanged. If the sheet is rectangular, the pivotal movement is performed about an axis which is located in the plane of the selected layer and is parallel to the shorter sides of the sheet

  16. Information Space, Information Field, Information Environment

    Directory of Open Access Journals (Sweden)

    Victor Ya. Tsvetkov

    2014-08-01

    Full Text Available The article analyzes information space, information field and information environment; shows that information space can be natural and artificial; information field is substantive and processual object and articulates the space property; information environment is concerned with some object and acts as the surrounding in relation to it and is considered with regard to it. It enables to define information environment as a subset of information space. It defines its passive description. Information environment can also be defined as a subset of information field. It corresponds to its active description.

  17. An Excursion Set Model of the Cosmic Web: the Abundance of Sheets, Filaments And Halos

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Jiajian; /Penn State U., Astron. Astrophys.; Abel, Tom; /KIPAC, Menlo Park; Mo, Houjun; /Massachusetts U., Amherst; Sheth, Ravi; /Pennsylvania U.

    2006-01-11

    We discuss an analytic approach for modeling structure formation in sheets, filaments and knots. This is accomplished by combining models of triaxial collapse with the excursion set approach: sheets are defined as objects which have collapsed along only one axis, filaments have collapsed along two axes, and halos are objects in which triaxial collapse is complete. In the simplest version of this approach, which we develop here, large scale structure shows a clear hierarchy of morphologies: the mass in large-scale sheets is partitioned up among lower mass filaments, which themselves are made-up of still lower mass halos. Our approach provides analytic estimates of the mass fraction in sheets, filaments and halos, and its evolution, for any background cosmological model and any initial fluctuation spectrum. In the currently popular {Lambda}CDM model, our analysis suggests that more than 99% of the mass in sheets, and 72% of the mass in filaments, is stored in objects more massive than 10{sup 10}M{sub {circle_dot}} at the present time. For halos, this number is only 46%. Our approach also provides analytic estimates of how halo abundances at any given time correlate with the morphology of the surrounding large-scale structure, and how halo evolution correlates with the morphology of large scale structure.

  18. fibrin–chitosan–sodium alginate composite sheet

    Indian Academy of Sciences (India)

    sodium alginate composite (F–C–SA) in sheet form. F–C–SA composite was prepared and characterized for its physicochemical properties like water absorption capacity, surface morphology, FTIR spectra and mechanical properties.

  19. HIV/AIDS Clinical Trials Fact Sheet

    Science.gov (United States)

    ... AIDS Drugs Clinical Trials Apps skip to content HIV Overview Home Understanding HIV/AIDS Fact Sheets HIV/ ... 4 p.m. ET) Send us an email HIV/AIDS Clinical Trials Last Reviewed: August 25, 2017 ...

  20. Advancing Concentrating Solar Power Research (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2014-02-01

    Researchers at the National Renewable Energy Laboratory (NREL) provide scientific, engineering, and analytical expertise to help advance innovation in concentrating solar power (CSP). This fact sheet summarizes how NREL is advancing CSP research.

  1. Greenland Radar Ice Sheet Thickness Measurements

    Data.gov (United States)

    National Aeronautics and Space Administration — Two 150-MHz coherent radar depth sounders were developed and flown over the Greenland ice sheet to obtain ice thickness measurements in support of PARCA...

  2. Hydrologic Outlets of the Greenland Ice Sheet

    Data.gov (United States)

    National Aeronautics and Space Administration — The Hydrologic Outlets of the Greenland Ice Sheet data set contains GIS point shapefiles that include 891 observed and potential hydrologic outlets of the Greenland...

  3. TIC and energy: Digital technologies and the environment; Understanding the energy challenges for technologies of information and communication; Data Centres; Energy savings and reduction of CO_2 emissions, objectives and action plan of the Orange Group

    International Nuclear Information System (INIS)

    Collet, Patrice; Gossart, Cedric; Garello, Rene; Richard, Philippe; Hauet, Jean-Pierre; Bourgoint, Jean-Claude; Zeddam, Ahmed

    2015-01-01

    This publication proposes a set of four articles which give an overview of the present situation of technologies of information and communication (TICs) in terms of energy consumption, and of their perspectives of evolution. More precisely, the authors propose an overview of negative and positive impacts of TICs on the environment (Digital technologies and the environment), discuss an analysis of energy consumption by the different components of the Internet (Understanding the energy challenges for technologies of information and communication), comment efforts which have been already achieved to reduce the energy consumed by data centre equipment (Data Centres), and present action developed and implemented by the Orange Group to manage its energy consumption in its networks and in its information system (Energy savings and reduction of CO_2 emissions, objectives and action plan of the Orange Group)

  4. Identification of computer graphics objects

    Directory of Open Access Journals (Sweden)

    Rossinskyi Yu.M.

    2016-04-01

    Full Text Available The article is devoted to the use of computer graphics methods in problems of creating drawings, charts, drafting, etc. The widespread use of these methods requires the development of efficient algorithms for the identification of objects of drawings. The article analyzes the model-making algorithms for this problem and considered the possibility of reducing the time using graphics editing operations. Editing results in such operations as copying, moving and deleting objects specified images. These operations allow the use of a reliable identification of images of objects methods. For information on the composition of the image of the object along with information about the identity and the color should include information about the spatial location and other characteristics of the object (the thickness and style of contour lines, fill style, and so on. In order to enable the pixel image analysis to structure the information it is necessary to enable the initial code image objects color. The article shows the results of the implementation of the algorithm of encoding object identifiers. To simplify the process of building drawings of any kind, and reduce time-consuming, method of drawing objects identification is proposed based on the use as the ID information of the object color.

  5. Ardnamurchan 3D cone-sheet architecture explained by a single elongate magma chamber.

    Science.gov (United States)

    Burchardt, Steffi; Troll, Valentin R; Mathieu, Lucie; Emeleus, Henry C; Donaldson, Colin H

    2013-10-08

    The Palaeogene Ardnamurchan central igneous complex, NW Scotland, was a defining place for the development of the classic concepts of cone-sheet and ring-dyke emplacement and has thus fundamentally influenced our thinking on subvolcanic structures. We have used the available structural information on Ardnamurchan to project the underlying three-dimensional (3D) cone-sheet structure. Here we show that a single elongate magma chamber likely acted as the source of the cone-sheet swarm(s) instead of the traditionally accepted model of three successive centres. This proposal is supported by the ridge-like morphology of the Ardnamurchan volcano and is consistent with the depth and elongation of the gravity anomaly underlying the peninsula. Our model challenges the traditional model of cone-sheet emplacement at Ardnamurchan that involves successive but independent centres in favour of a more dynamical one that involves a single, but elongate and progressively evolving magma chamber system.

  6. The Research on Elevation Change of Antarctic Ice Sheet Based on CRYOSAT-2 Alimeter

    Science.gov (United States)

    Sun, Q.; Wan, J.; Liu, S.; Li, Y.

    2018-04-01

    In this paper, the Cryosat-2 altimeter data distributed by the ESA, and these data are processed to extract the information of the elevation change of the Antarctic ice sheet from 2010 to 2017. Firstly, the main pretreatment preprocessing for Cryosat-2 altimetry data is crossover adjustment and elimination of rough difference. Then the grid DEM of the Antarctic ice sheet was constructed by using the kriging interpolation method,and analyzed the spatial characteristic time characteristics of the Antarctic ice sheet. The latitude-weighted elevation can be obtained by using the elevation data of each cycle, and then the general trend of the Antarctic ice sheet elevation variation can be seen roughly.

  7. Fact sheet: Ethanol from corn

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-31

    This fact sheet is intended to provide an overview of the advantages of ethanol from corn, emphasizing ethanol`s contribution to environmental protection and sustainable agriculture. Ethanol, an alternative fuel used as an octane enhancer is produced through the conversion of starch to sugars by enzymes, and fermentation of these sugars to ethanol by yeast. The production process may involve wet milling or dry milling. Both these processes produce valuable by-products, in addition to ethanol and carbon dioxide. Ethanol contains about 32,000 BTU per litre. It is commonly believed that using state-of-the-art corn farming and corn processing processes, the amount of energy contained in ethanol and its by-products would be more than twice the energy required to grow and process corn into ethanol. Ethanol represents the third largest market for Ontario corn, after direct use as animal feed and wet milling for starch, corn sweetener and corn oil. The environmental consequences of using ethanol are very significant. It is estimated that a 10 per cent ethanol blend in gasoline would result in a 25 to 30 per cent decrease in carbon monoxide emissions, a 6 to 10 per cent decrease in net carbon dioxide, a slight increase in nitrous oxide emissions which, however, would still result in an overall decrease in ozone formation, since the significant reduction in carbon monoxide emissions would compensate for any slight increase in nitrous oxide. Volatile organic compounds emission would also decrease by about 7 per cent with a 10 per cent ethanol blend. High level blends could reduce VOCs production by as much as 30 per cent. 7 refs.

  8. Energized Oxygen : Speiser Current Sheet Bifurcation

    Science.gov (United States)

    George, D. E.; Jahn, J. M.

    2017-12-01

    A single population of energized Oxygen (O+) is shown to produce a cross-tail bifurcated current sheet in 2.5D PIC simulations of the magnetotail without the influence of magnetic reconnection. Treatment of oxygen in simulations of space plasmas, specifically a magnetotail current sheet, has been limited to thermal energies despite observations of and mechanisms which explain energized ions. We performed simulations of a homogeneous oxygen background, that has been energized in a physically appropriate manner, to study the behavior of current sheets and magnetic reconnection, specifically their bifurcation. This work uses a 2.5D explicit Particle-In-a-Cell (PIC) code to investigate the dynamics of energized heavy ions as they stream Dawn-to-Dusk in the magnetotail current sheet. We present a simulation study dealing with the response of a current sheet system to energized oxygen ions. We establish a, well known and studied, 2-species GEM Challenge Harris current sheet as a starting point. This system is known to eventually evolve and produce magnetic reconnection upon thinning of the current sheet. We added a uniform distribution of thermal O+ to the background. This 3-species system is also known to eventually evolve and produce magnetic reconnection. We add one additional variable to the system by providing an initial duskward velocity to energize the O+. We also traced individual particle motion within the PIC simulation. Three main results are shown. First, energized dawn- dusk streaming ions are clearly seen to exhibit sustained Speiser motion. Second, a single population of heavy ions clearly produces a stable bifurcated current sheet. Third, magnetic reconnection is not required to produce the bifurcated current sheet. Finally a bifurcated current sheet is compatible with the Harris current sheet model. This work is the first step in a series of investigations aimed at studying the effects of energized heavy ions on magnetic reconnection. This work differs

  9. Catalogue of Energy Efficiency Measures for France: descriptive fact sheets

    International Nuclear Information System (INIS)

    2012-06-01

    ADEME wished to learn about existing effective energy efficiency measures implemented outside of France, whether cross-sectoral or targeted at a specific sector (industry, transport, buildings or agriculture). The objective of this survey was to determine whether any of these measures could be applied in France, with the goal of holding down the growth of energy consumption. This survey has led to the writing of a catalog of 53 two-page fact sheets describing the measures identified as interesting for France. These measures were analysed via classic criteria of evaluation such as cost-efficiency or impact, allowing to highlight the most successful measures for the French territory

  10. Resistance and sheet resistance measurements using electron beam induced current

    International Nuclear Information System (INIS)

    Czerwinski, A.; Pluska, M.; Ratajczak, J.; Szerling, A.; KaPtcki, J.

    2006-01-01

    A method for measurement of spatially uniform or nonuniform resistance in layers and strips, based on electron beam induced current (EBIC) technique, is described. High electron beam currents are used so that the overall resistance of the measurement circuit affects the EBIC signal. During the evaluation, the electron beam is scanned along the measured object, whose load resistance varies with the distance. The variation is compensated by an adjustable resistance within an external circuit. The method has been experimentally deployed for sheet resistance determination of buried regions of lateral confinements in semiconductor laser heterostructures manufactured by molecular beam epitaxy

  11. Copper contamination in thin stainless steel sheet

    International Nuclear Information System (INIS)

    Holbert, R.K. Jr.; Dobbins, A.G.; Bennett, R.K. Jr.

    1986-01-01

    The standard welding technique used at Oak Ridge Y-12 Plant for joining thin stainless sheet is the gas tungsten arc (GTA) welding process. One of the reoccurring problems with the sheet welds is surface cracking in the heat-affected zone (HAZ). Metallography shows that the cracks are only about 0.05 mm (0.002 in.) deep which is significant in a 0.25 mm (0.01 in.) thick sheet. Thus, welding requirements do not permit any surfacing cracking as detected by a fluorescent dye penetrant test conducted on every part after welding. Surface cracks have been found in both of the two most common weld designs in the thin sheet fabricated at the Oak Ridge Y-12 Plant. These butt joints are welded between two 0.25 mm thick stainless steel sheets and a tube with eyelet welded to a 25 mm (0.98 in.) thick sheet. The weld between the two sheets is made on a semiautomatic seam welding unit, whereas the tube-to-eyelet-to-sheet welds are done manually. The quality of both welds is very dependent on the welding procedure and the way the parts are placed in the weld fixturing. Metallographic examination has indicated that some welded parts with surface cracking in the weld region had copper particles on the surface, and the question of copper contamination has been raised. With the aid of a scanning electron microscope and an electron microprobe, the existence of copper in an around the surface cracks has been verified. The copper is on the surface of the parts prior to welding in the form of small dust particles

  12. Balance of the West Antarctic Ice Sheet

    Science.gov (United States)

    2002-01-01

    For several decades, measurements of the West Antarctic Ice Sheet showed it to be retreating rapidly. But new data derived from satellite-borne radar sensors show the ice sheet to be growing. Changing Antarctic ice sheets remains an area of high scientific interest, particularly in light of recent global warming concerns. These new findings are significant because scientists estimate that sea level would rise 5-6 meters (16-20 feet) if the ice sheet collapsed into the sea. Do these new measurements signal the end of the ice sheet's 10,000-year retreat? Or, are these new satellite data simply much more accurate than the sparse ice core and surface measurements that produced the previous estimates? Another possibility is that the ice accumulation may simply indicate that the ice sheet naturally expands and retreats in regular cycles. Cryologists will grapple with these questions, and many others, as they examine the new data. The image above depicts the region of West Antarctica where scientists measured ice speed. The fast-moving central ice streams are shown in red. Slower tributaries feeding the ice streams are shown in blue. Green areas depict slow-moving, stable areas. Thick black lines depict the areas that collect snowfall to feed their respective ice streams. Reference: Ian Joughin and Slawek Tulaczyk Science Jan 18 2002: 476-480. Image courtesy RADARSAT Antarctic Mapping Project

  13. Antibubbles and fine cylindrical sheets of air

    KAUST Repository

    Beilharz, D.

    2015-08-14

    Drops impacting at low velocities onto a pool surface can stretch out thin hemispherical sheets of air between the drop and the pool. These air sheets can remain intact until they reach submicron thicknesses, at which point they rupture to form a myriad of microbubbles. By impacting a higher-viscosity drop onto a lower-viscosity pool, we have explored new geometries of such air films. In this way we are able to maintain stable air layers which can wrap around the entire drop to form repeatable antibubbles, i.e. spherical air layers bounded by inner and outer liquid masses. Furthermore, for the most viscous drops they enter the pool trailing a viscous thread reaching all the way to the pinch-off nozzle. The air sheet can also wrap around this thread and remain stable over an extended period of time to form a cylindrical air sheet. We study the parameter regime where these structures appear and their subsequent breakup. The stability of these thin cylindrical air sheets is inconsistent with inviscid stability theory, suggesting stabilization by lubrication forces within the submicron air layer. We use interferometry to measure the air-layer thickness versus depth along the cylindrical air sheet and around the drop. The air film is thickest above the equator of the drop, but thinner below the drop and up along the air cylinder. Based on microbubble volumes, the thickness of the cylindrical air layer becomes less than 100 nm before it ruptures.

  14. Buckling Behavior of Substrate Supported Graphene Sheets

    Directory of Open Access Journals (Sweden)

    Kuijian Yang

    2016-01-01

    Full Text Available The buckling of graphene sheets on substrates can significantly degrade their performance in materials and devices. Therefore, a systematic investigation on the buckling behavior of monolayer graphene sheet/substrate systems is carried out in this paper by both molecular mechanics simulations and theoretical analysis. From 70 simulation cases of simple-supported graphene sheets with different sizes under uniaxial compression, two different buckling modes are investigated and revealed to be dominated by the graphene size. Especially, for graphene sheets with length larger than 3 nm and width larger than 1.1 nm, the buckling mode depends only on the length/width ratio. Besides, it is revealed that the existence of graphene substrate can increase the critical buckling stress and strain to 4.39 N/m and 1.58%, respectively, which are about 10 times those for free-standing graphene sheets. Moreover, for graphene sheets with common size (longer than 20 nm, both theoretical and simulation results show that the critical buckling stress and strain are dominated only by the adhesive interactions with substrate and independent of the graphene size. Results in this work provide valuable insight and guidelines for the design and application of graphene-derived materials and nano-electromechanical systems.

  15. Antibubbles and fine cylindrical sheets of air

    KAUST Repository

    Beilharz, D.; Guyon, A.; Li, E.  Q.; Thoraval, M.-J.; Thoroddsen, Sigurdur T

    2015-01-01

    Drops impacting at low velocities onto a pool surface can stretch out thin hemispherical sheets of air between the drop and the pool. These air sheets can remain intact until they reach submicron thicknesses, at which point they rupture to form a myriad of microbubbles. By impacting a higher-viscosity drop onto a lower-viscosity pool, we have explored new geometries of such air films. In this way we are able to maintain stable air layers which can wrap around the entire drop to form repeatable antibubbles, i.e. spherical air layers bounded by inner and outer liquid masses. Furthermore, for the most viscous drops they enter the pool trailing a viscous thread reaching all the way to the pinch-off nozzle. The air sheet can also wrap around this thread and remain stable over an extended period of time to form a cylindrical air sheet. We study the parameter regime where these structures appear and their subsequent breakup. The stability of these thin cylindrical air sheets is inconsistent with inviscid stability theory, suggesting stabilization by lubrication forces within the submicron air layer. We use interferometry to measure the air-layer thickness versus depth along the cylindrical air sheet and around the drop. The air film is thickest above the equator of the drop, but thinner below the drop and up along the air cylinder. Based on microbubble volumes, the thickness of the cylindrical air layer becomes less than 100 nm before it ruptures.

  16. Summary of the evidence of breast cancer service screening outcomes in Europe and first estimate of the benefit and harm balance sheet

    DEFF Research Database (Denmark)

    Paci, Eugenio; Lynge, Elsebeth

    2012-01-01

    To construct a European 'balance sheet' of key outcomes of population-based mammographic breast cancer screening, to inform policy-makers, stakeholders and invited women.......To construct a European 'balance sheet' of key outcomes of population-based mammographic breast cancer screening, to inform policy-makers, stakeholders and invited women....

  17. Bayesian Inversion for Large Scale Antarctic Ice Sheet Flow

    KAUST Repository

    Ghattas, Omar

    2015-01-07

    The flow of ice from the interior of polar ice sheets is the primary contributor to projected sea level rise. One of the main difficulties faced in modeling ice sheet flow is the uncertain spatially-varying Robin boundary condition that describes the resistance to sliding at the base of the ice. Satellite observations of the surface ice flow velocity, along with a model of ice as a creeping incompressible shear-thinning fluid, can be used to infer this uncertain basal boundary condition. We cast this ill-posed inverse problem in the framework of Bayesian inference, which allows us to infer not only the basal sliding parameters, but also the associated uncertainty. To overcome the prohibitive nature of Bayesian methods for large-scale inverse problems, we exploit the fact that, despite the large size of observational data, they typically provide only sparse information on model parameters. We show results for Bayesian inversion of the basal sliding parameter field for the full Antarctic continent, and demonstrate that the work required to solve the inverse problem, measured in number of forward (and adjoint) ice sheet model solves, is independent of the parameter and data dimensions

  18. Bayesian Inversion for Large Scale Antarctic Ice Sheet Flow

    KAUST Repository

    Ghattas, Omar

    2015-01-01

    The flow of ice from the interior of polar ice sheets is the primary contributor to projected sea level rise. One of the main difficulties faced in modeling ice sheet flow is the uncertain spatially-varying Robin boundary condition that describes the resistance to sliding at the base of the ice. Satellite observations of the surface ice flow velocity, along with a model of ice as a creeping incompressible shear-thinning fluid, can be used to infer this uncertain basal boundary condition. We cast this ill-posed inverse problem in the framework of Bayesian inference, which allows us to infer not only the basal sliding parameters, but also the associated uncertainty. To overcome the prohibitive nature of Bayesian methods for large-scale inverse problems, we exploit the fact that, despite the large size of observational data, they typically provide only sparse information on model parameters. We show results for Bayesian inversion of the basal sliding parameter field for the full Antarctic continent, and demonstrate that the work required to solve the inverse problem, measured in number of forward (and adjoint) ice sheet model solves, is independent of the parameter and data dimensions

  19. Start-up First Term Sheet: Stumbling Blocks to Avoid

    Directory of Open Access Journals (Sweden)

    Amalyan Nataly D.

    2018-01-01

    Full Text Available Start-up relationships with business angel and/or venture capital are similar to a marriage – but with a divorce in mind. The latter necessitates a proper prenuptial agreement signing at the very beginning of the relations. In case of business angel and/or venture capital we are speaking about Term sheet, determining pricing, powers and duties of the board, as well as information, participation and protective rights for the partners. Standard Term sheet consists of three buckets of provisions, defining: (i terms impacting start-up valuation and economic division of profits and proceeds upon a liquidity event, (ii terms impacting control over decision making and (iii investor protection terms. This article focuses on financial and economic aspects of funding agreement, exposing some tricky parts of the Term sheet, threatening to transform potential win-win deals into rupture of relations, crash of the company or even legal battles. The results of the analysis are used to substantiate growing in popular appeal thesis that raising too much money can be detrimental for a startup.

  20. Nuclear Fuel Cycle Objectives

    International Nuclear Information System (INIS)

    2013-01-01

    One of the IAEA's statutory objectives is to 'seek to accelerate and enlarge the contribution of atomic energy to peace, health and prosperity throughout the world'. One way this objective is achieved is through the publication of a range of technical series. Two of these are the IAEA Nuclear Energy Series and the IAEA Safety Standards Series. According to Article III.A.6 of the IAEA Statute, the safety standards establish 'standards of safety for protection of health and minimization of danger to life and property'. The safety standards include the Safety Fundamentals, Safety Requirements and Safety Guides. These standards are written primarily in a regulatory style, and are binding on the IAEA for its own programmes. The principal users are the regulatory bodies in member States and other national authorities. The IAEA Nuclear Energy Series comprises reports designed to encourage and assist R and D on, and application of, nuclear energy for peaceful uses. This includes practical examples to be used by owners and operators of utilities in member States, implementing organizations, academia and government officials, among others. This information is presented in guides, reports on technology status and advances, and best practices for peaceful uses of nuclear energy based on inputs from international experts. The IAEA Nuclear Energy Series complements the IAEA Safety Standards Series. The Nuclear Energy Basic Principles is the highest level publication in the IAEA Nuclear Energy Series, and describes the rationale and vision for the peaceful uses of nuclear energy. It presents eight Basic Principles on which nuclear energy systems should be based to fulfil nuclear energy's potential to help meet growing global energy needs. The Nuclear Energy Series Objectives are the second level publications. They describe what needs to be considered and the specific goals to be achieved at different stages of implementation, all of which are consistent with the Basic Principles

  1. Final Air Toxics Standards for Clay Ceramics Manufacturing, Glass Manufacturing, and Secondary Nonferrous Metals Processing Area Sources Fact Sheet

    Science.gov (United States)

    This page contains a December 2007 fact sheet with information regarding the National Emissions Standards for Hazardous Air Pollutants (NESHAP) for Clay Ceramics Manufacturing, Glass Manufacturing, and Secondary Nonferrous Metals Processing Area Sources

  2. 17 CFR 210.6-04 - Balance sheets.

    Science.gov (United States)

    2010-04-01

    ... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Balance sheets. 210.6-04... sheets. This rule is applicable to balance sheets filed by registered investment companies except for... of this part. Balance sheets filed under this rule shall comply with the following provisions: Assets...

  3. Radioactive Waste Management Objectives

    International Nuclear Information System (INIS)

    2011-01-01

    One of the IAEA's statutory objectives is to 'seek to accelerate and enlarge the contribution of atomic energy to peace, health and prosperity throughout the world'. One way it achieves this objective is to issue publications in various series. Two of these series are the IAEA Nuclear Energy Series and the IAEA Safety Standards Series. According to Article III, paragraph A.6, of the IAEA Statute, the IAEA safety standards establish 'standards of safety for protection of health and minimization of danger to life and property.' The safety standards include the Safety Fundamentals, Safety Requirements and Safety Guides. These standards are primarily written in a regulatory style, and are binding on the IAEA for its own activities. The principal users are Member State regulatory bodies and other national authorities. The IAEA Nuclear Energy Series consists of reports designed to encourage and assist research on, and development and practical application of, nuclear energy for peaceful uses. This includes practical examples to be used by owners and operators of utilities in Member States, implementing organizations, academia and politicians, among others. The information is presented in guides, reports on the status of technology and advances, and best practices for peaceful uses of nuclear energy based on inputs from international experts. The series complements the IAEA's safety standards, and provides detailed guidance, experience, good practices and examples on the five areas covered in the IAEA Nuclear Energy Series. The Nuclear Energy Basic Principles is the highest level publication in the IAEA Nuclear Energy Series and describes the rationale and vision for the peaceful uses of nuclear energy. It presents eight Basic Principles on which nuclear energy systems should be based to fulfil nuclear energy's potential to help meet growing global energy needs. The Nuclear Energy Series Objectives are the second level publications. They describe what needs to be

  4. Object Knowledge Modulates Colour Appearance

    Directory of Open Access Journals (Sweden)

    Christoph Witzel

    2011-01-01

    Full Text Available We investigated the memory colour effect for colour diagnostic artificial objects. Since knowledge about these objects and their colours has been learned in everyday life, these stimuli allow the investigation of the influence of acquired object knowledge on colour appearance. These investigations are relevant for questions about how object and colour information in high-level vision interact as well as for research about the influence of learning and experience on perception in general. In order to identify suitable artificial objects, we developed a reaction time paradigm that measures (subjective colour diagnosticity. In the main experiment, participants adjusted sixteen such objects to their typical colour as well as to grey. If the achromatic object appears in its typical colour, then participants should adjust it to the opponent colour in order to subjectively perceive it as grey. We found that knowledge about the typical colour influences the colour appearance of artificial objects. This effect was particularly strong along the daylight axis.

  5. Object knowledge modulates colour appearance

    Science.gov (United States)

    Witzel, Christoph; Valkova, Hanna; Hansen, Thorsten; Gegenfurtner, Karl R

    2011-01-01

    We investigated the memory colour effect for colour diagnostic artificial objects. Since knowledge about these objects and their colours has been learned in everyday life, these stimuli allow the investigation of the influence of acquired object knowledge on colour appearance. These investigations are relevant for questions about how object and colour information in high-level vision interact as well as for research about the influence of learning and experience on perception in general. In order to identify suitable artificial objects, we developed a reaction time paradigm that measures (subjective) colour diagnosticity. In the main experiment, participants adjusted sixteen such objects to their typical colour as well as to grey. If the achromatic object appears in its typical colour, then participants should adjust it to the opponent colour in order to subjectively perceive it as grey. We found that knowledge about the typical colour influences the colour appearance of artificial objects. This effect was particularly strong along the daylight axis. PMID:23145224

  6. Object width modulates object-based attentional selection.

    Science.gov (United States)

    Nah, Joseph C; Neppi-Modona, Marco; Strother, Lars; Behrmann, Marlene; Shomstein, Sarah

    2018-04-24

    Visual input typically includes a myriad of objects, some of which are selected for further processing. While these objects vary in shape and size, most evidence supporting object-based guidance of attention is drawn from paradigms employing two identical objects. Importantly, object size is a readily perceived stimulus dimension, and whether it modulates the distribution of attention remains an open question. Across four experiments, the size of the objects in the display was manipulated in a modified version of the two-rectangle paradigm. In Experiment 1, two identical parallel rectangles of two sizes (thin or thick) were presented. Experiments 2-4 employed identical trapezoids (each having a thin and thick end), inverted in orientation. In the experiments, one end of an object was cued and participants performed either a T/L discrimination or a simple target-detection task. Combined results show that, in addition to the standard object-based attentional advantage, there was a further attentional benefit for processing information contained in the thick versus thin end of objects. Additionally, eye-tracking measures demonstrated increased saccade precision towards thick object ends, suggesting that Fitts's Law may play a role in object-based attentional shifts. Taken together, these results suggest that object-based attentional selection is modulated by object width.

  7. Adobe Boxes: Locating Object Proposals Using Object Adobes.

    Science.gov (United States)

    Fang, Zhiwen; Cao, Zhiguo; Xiao, Yang; Zhu, Lei; Yuan, Junsong

    2016-09-01

    Despite the previous efforts of object proposals, the detection rates of the existing approaches are still not satisfactory enough. To address this, we propose Adobe Boxes to efficiently locate the potential objects with fewer proposals, in terms of searching the object adobes that are the salient object parts easy to be perceived. Because of the visual difference between the object and its surroundings, an object adobe obtained from the local region has a high probability to be a part of an object, which is capable of depicting the locative information of the proto-object. Our approach comprises of three main procedures. First, the coarse object proposals are acquired by employing randomly sampled windows. Then, based on local-contrast analysis, the object adobes are identified within the enlarged bounding boxes that correspond to the coarse proposals. The final object proposals are obtained by converging the bounding boxes to tightly surround the object adobes. Meanwhile, our object adobes can also refine the detection rate of most state-of-the-art methods as a refinement approach. The extensive experiments on four challenging datasets (PASCAL VOC2007, VOC2010, VOC2012, and ILSVRC2014) demonstrate that the detection rate of our approach generally outperforms the state-of-the-art methods, especially with relatively small number of proposals. The average time consumed on one image is about 48 ms, which nearly meets the real-time requirement.

  8. Delphi FND Application Object Library -

    Data.gov (United States)

    Department of Transportation — Delphi FND Application Object Library contains the following data elements, but are not limited to temporary data tables for the logged in session, information about...

  9. Best Management Practice, Fact Sheet 2. Sheet Flow to Open Space

    OpenAIRE

    Sample, David; Doumar, Lia

    2013-01-01

    This publication explains what sheet flow to open space is, where and how it is used, their limitations, routine and nonroutine maintenance, expected costs, and a glossary of terms. This fact sheet is one of a 15-part series on urban stormwater management practices.

  10. BRITICE-CHRONO: Constraining rates and style of marine-influenced ice sheet decay to provide a data-rich playground for ice sheet modellers

    Science.gov (United States)

    Clark, Chris

    2014-05-01

    Uncertainty exists regarding the fate of the Antarctic and Greenland ice sheets and how they will respond to forcings from sea level and atmospheric and ocean temperatures. If we want to know more about the mechanisms and rate of change of shrinking ice sheets, then why not examine an ice sheet that has fully disappeared and track its retreat through time? If achieved in enough detail such information could become a data-rich playground for improving the next breed of numerical ice sheet models to be used in ice and sea level forecasting. We regard that the last British-Irish Ice Sheet is a good target for this work, on account of its small size, density of information and with its numerous researchers already investigating it. BRITICE-CHRONO is a large (>45 researchers) NERC-funded consortium project comprising Quaternary scientists and glaciologists who will search the seafloor around Britain and Ireland and parts of the landmass in order to find and extract samples of sand, rock and organic matter that can be dated (OSL; Cosmogenic; 14C) to reveal the timing and rate of change of the collapsing British-Irish Ice Sheet. The purpose is to produce a high resolution dataset on the demise on an ice sheet - from the continental shelf edge and across the marine to terrestrial transition. Some 800 new date assessments will be added to those that already exist. This poster reports on the hypotheses that underpin the work. Data on retreat will be collected by focusing on 8 transects running from the continental shelf edge to a short distance (10s km) onshore and acquiring marine and terrestrial samples for geochronometric dating. The project includes funding for 587 radiocarbon, 140 OSL and 158 TCN samples for surface exposure dating; with sampling accomplished by two research cruises and 16 fieldwork campaigns. Results will reveal the timing and rate of change of ice margin recession for each transect, and combined with existing landform and dating databases, will be

  11. The subjective experience of object recognition: comparing metacognition for object detection and object categorization.

    Science.gov (United States)

    Meuwese, Julia D I; van Loon, Anouk M; Lamme, Victor A F; Fahrenfort, Johannes J

    2014-05-01

    Perceptual decisions seem to be made automatically and almost instantly. Constructing a unitary subjective conscious experience takes more time. For example, when trying to avoid a collision with a car on a foggy road you brake or steer away in a reflex, before realizing you were in a near accident. This subjective aspect of object recognition has been given little attention. We used metacognition (assessed with confidence ratings) to measure subjective experience during object detection and object categorization for degraded and masked objects, while objective performance was matched. Metacognition was equal for degraded and masked objects, but categorization led to higher metacognition than did detection. This effect turned out to be driven by a difference in metacognition for correct rejection trials, which seemed to be caused by an asymmetry of the distractor stimulus: It does not contain object-related information in the detection task, whereas it does contain such information in the categorization task. Strikingly, this asymmetry selectively impacted metacognitive ability when objective performance was matched. This finding reveals a fundamental difference in how humans reflect versus act on information: When matching the amount of information required to perform two tasks at some objective level of accuracy (acting), metacognitive ability (reflecting) is still better in tasks that rely on positive evidence (categorization) than in tasks that rely more strongly on an absence of evidence (detection).

  12. Bessel light sheet structured illumination microscopy

    Science.gov (United States)

    Noshirvani Allahabadi, Golchehr

    Biomedical study researchers using animals to model disease and treatment need fast, deep, noninvasive, and inexpensive multi-channel imaging methods. Traditional fluorescence microscopy meets those criteria to an extent. Specifically, two-photon and confocal microscopy, the two most commonly used methods, are limited in penetration depth, cost, resolution, and field of view. In addition, two-photon microscopy has limited ability in multi-channel imaging. Light sheet microscopy, a fast developing 3D fluorescence imaging method, offers attractive advantages over traditional two-photon and confocal microscopy. Light sheet microscopy is much more applicable for in vivo 3D time-lapsed imaging, owing to its selective illumination of tissue layer, superior speed, low light exposure, high penetration depth, and low levels of photobleaching. However, standard light sheet microscopy using Gaussian beam excitation has two main disadvantages: 1) the field of view (FOV) of light sheet microscopy is limited by the depth of focus of the Gaussian beam. 2) Light-sheet images can be degraded by scattering, which limits the penetration of the excitation beam and blurs emission images in deep tissue layers. While two-sided sheet illumination, which doubles the field of view by illuminating the sample from opposite sides, offers a potential solution, the technique adds complexity and cost to the imaging system. We investigate a new technique to address these limitations: Bessel light sheet microscopy in combination with incoherent nonlinear Structured Illumination Microscopy (SIM). Results demonstrate that, at visible wavelengths, Bessel excitation penetrates up to 250 microns deep in the scattering media with single-side illumination. Bessel light sheet microscope achieves confocal level resolution at a lateral resolution of 0.3 micron and an axial resolution of 1 micron. Incoherent nonlinear SIM further reduces the diffused background in Bessel light sheet images, resulting in

  13. [Continuing medical education and the Social Balance Sheet].

    Science.gov (United States)

    Gatti, Giorgio

    2010-06-01

    The social balance sheet is an instrument used to obtain a clear and transparent account, that helps to develop an analysis of the budget from the point of view of the stakeholders; this is not all that is required by law, but it takes into account the ability of the health institutions to obtain a collaboration with the neighboring environment and with the social issues that enter into the relationship. This could be a valuable tool also for educational purposes; it is an useful task to be performed by the health workers, and an opportunity to redefine the information needs through the analysis of the results achieved.

  14. Impact of mismatched and misaligned laser light sheet profiles on PIV performance

    Science.gov (United States)

    Grayson, K.; de Silva, C. M.; Hutchins, N.; Marusic, I.

    2018-01-01

    The effect of mismatched or misaligned laser light sheet profiles on the quality of particle image velocimetry (PIV) results is considered in this study. Light sheet profiles with differing widths, shapes, or alignment can reduce the correlation between PIV images and increase experimental errors. Systematic PIV simulations isolate these behaviours to assess the sensitivity and implications of light sheet mismatch on measurements. The simulations in this work use flow fields from a turbulent boundary layer; however, the behaviours and impacts of laser profile mismatch are highly relevant to any fluid flow or PIV application. Experimental measurements from a turbulent boundary layer facility are incorporated, as well as additional simulations matched to experimental image characteristics, to validate the synthetic image analysis. Experimental laser profiles are captured using a modular laser profiling camera, designed to quantify the distribution of laser light sheet intensities and inform any corrective adjustments to an experimental configuration. Results suggest that an offset of just 1.35 standard deviations in the Gaussian light sheet intensity distributions can cause a 40% reduction in the average correlation coefficient and a 45% increase in spurious vectors. Errors in measured flow statistics are also amplified when two successive laser profiles are no longer well matched in alignment or intensity distribution. Consequently, an awareness of how laser light sheet overlap influences PIV results can guide faster setup of an experiment, as well as achieve superior experimental measurements.

  15. Electrochemical profiling of multi-clad aluminium sheets used in automotive heat exchangers

    DEFF Research Database (Denmark)

    Bordo, Kirill; Ambat, Rajan; Peguet, Lionel

    2014-01-01

    The objective of the present study is to understand the mechanisms of corrosion propagation across the multi-clad structure of Al alloys sheets as a function of local alloy composition and microstructure, with and without brazing treatment. Electro-chemical behaviour at different depths was profi...

  16. The Distribution of Basal Water Beneath the Greenland Ice Sheet from Radio-Echo Sounding

    Science.gov (United States)

    Jordan, T.; Williams, C.; Schroeder, D. M.; Martos, Y. M.; Cooper, M.; Siegert, M. J.; Paden, J. D.; Huybrechts, P.; Bamber, J. L.

    2017-12-01

    There is widespread, but often indirect, evidence that a significant fraction of the Greenland Ice Sheet is thawed at the bed. This includes major outlet glaciers and around the NorthGRIP ice-core in the interior. However, the ice-sheet-wide distribution of basal water is poorly constrained by existing observations, and the spatial relationship between basal water and other ice-sheet and subglacial properties is therefore largely unexplored. In principle, airborne radio-echo sounding (RES) surveys provide the necessary information and spatial coverage to infer the presence of basal water at the ice-sheet scale. However, due to uncertainty and spatial variation in radar signal attenuation, the commonly used water diagnostic, bed-echo reflectivity, is highly ambiguous and prone to spatial bias. Here we introduce a new RES diagnostic for the presence of basal water which incorporates both sharp step-transitions and rapid fluctuations in bed-echo reflectivity. This has the advantage of being (near) independent of attenuation model, and enables a decade of recent Operation Ice Bride RES survey data to be combined in a single map for basal water. The ice-sheet-wide water predictions are compared with: bed topography and drainage network structure, existing knowledge of the thermal state and geothermal heat flux, and ice velocity. In addition to the fast flowing ice-sheet margins, we also demonstrate widespread water routing and storage in parts of the slow-flowing northern interior. Notably, this includes a quasi-linear `corridor' of basal water, extending from NorthGRIP to Petermann glacier, which spatially correlates with a region of locally high (magnetic-derived) geothermal heat flux. The predicted water distribution places a new constraint upon the basal thermal state of the Greenland Ice Sheet, and could be used as an input for ice-sheet model simulations.

  17. Can I look at my list? An evaluation of a 'prompt sheet' within an oncology outpatient clinic.

    Science.gov (United States)

    Glynne-Jones, R; Ostler, P; Lumley-Graybow, S; Chait, I; Hughes, R; Grainger, J; Leverton, T J

    2006-06-01

    We introduced a patient 'prompt sheet' into our clinic between January 2004 and January 2005. The aim was to determine whether it would facilitate communication and help patients in obtaining their desired level of information about their illness, and assist with decision making. We conducted an audit survey to investigate the way follow-up takes place in our oncology clinic, to determine what works and what does not work in the clinic, and to examine how patients access the most useful information and to assess the utility of, and patient satisfaction with, a locally developed pilot prompt sheet. A single questionnaire was designed to elicit information on patients' information needs, overall satisfaction with the oncology clinic, and uptake and perceived usefulness of the prompt sheet. We carried out an audit survey in the form of a Likert-scale questionnaire (33 questions), followed immediately afterwards by a semi-structured interview. A specialist nurse asked a range of open questions about what was good and bad about the clinic and the prompt sheets. Despite efforts to ensure that all patients received the prompt-sheet leaflets, only 254 out of 300 (85%) received them. Of these, 195 (65%) felt that they were 'very helpful', and 30 (10%) found them 'fairly helpful'. However, 15 (5%) had no strong feelings and only three found them either fairly or completely unhelpful. One-third of the patients were able to ask more questions about their disease as a result of the prompt sheet, although they felt the doctor was busy and did not want to take up too much of their time. Men with prostate cancer found the prompt sheet particularly helpful to ask questions. This satisfaction audit suggests that our pilot prompt sheet is helpful to patients attending oncology outpatient appointments, particularly for men with prostate cancer. We aim to adapt the present prompt sheet on the basis of the replies obtained, and re-audit in the future.

  18. Internal Controls for Accounting Areas. Alliance Action Information Sheets

    Science.gov (United States)

    Technical Assistance ALLIANCE for Parent Centers, 2006

    2006-01-01

    Internal controls are important to ensure your Parent Center's resources are well protected. Steps should be taken to ensure that finance transactions are authorized by management, executed properly and on time, and recorded appropriately. Some centers may not have staff with all of the titles used in the procedures presented in this paper.…

  19. Separations in Communication Complexity Using Cheat Sheets and Information Complexity

    NARCIS (Netherlands)

    A. Anshu (Anurag); A. Belovs (Aleksandr); S. Ben-David (Shalev); M. Goos (Mika); R. Jain (Rahul); R. Kothari (Robin); T. J. Lee (Troy); M. Santha (Miklos)

    2016-01-01

    textabstractWhile exponential separations are known between quantum and randomized communication complexity for partial functions (Raz, STOC 1999), the best known separation between these measures for a total function is quadratic, witnessed by the disjointness function. We give the first

  20. Other Solid Waste Incineration (OSWI) Units Standards of Performance for New Stationary Sources and Emission Guidelines for Existing Sources Fact Sheets

    Science.gov (United States)

    This page contains a November 2005, and and November 2006 fact sheet with information regarding the final and proposed NSPS and Emission Guidelines for Existing Sources for OSWI. This document provides a summary of the information for this regulation