WorldWideScience

Sample records for nuclear materials proceedings

  1. Proceedings of the Fifth Seminar on Technology of Nuclear Materials Safety

    International Nuclear Information System (INIS)

    Indro Yuwono; Nababan, Binsar; Suharyanta

    2004-11-01

    Proceedings of the Fifth Seminar on Technology of Nuclear Material Safety all aspect of research activity concerning the role of physical protection, nuclear safeguards technology and international convection in supporting the establishment of Nuclear Power Plant in Indonesia. There are 16 articles which have separated index. (PPIN)

  2. Nuclear Materials Management. Proceedings of the Symposium on Nuclear Materials Management

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1966-02-15

    An increasing number of countries are using nuclear materials which, because of their high value and the potential hazards involved, require special methods of handling. To discuss these and to provide a forum at which different systems for achieving the necessary economy and safety could be compared, the International Atomic Energy Agency held a Symposium at Vienna on Nuclear Materials Management from 30 August to 3 September, 1965. It was attended by 115 participants from 19 Member States and two international organizations. Nuclear materials are already being used on an industrial scale and their high cost demands close and continuous control to ensure that they are delivered precisely on time and that they are used to the fullest possible extent before they are withdrawn from service. Routine industrial methods of material control and verification are widely used to ensure safe and economical operation and handling in nuclear power stations, in fuel-element fabrication and reprocessing plants, and in storage facilities. In addition special refinements are needed to take account of the value and the degree of purity required of nuclear materials. Quality as well as quantity has to be checked thoroughly and the utmost economy in processing is necessary. The radioactivity of the material poses special problems of handling and storage and creates a potential hazard to health. A further problem is that of criticality. These dangers and the means of averting them are well understood, as is evidenced by the outstandingly good safety record of the atomic energy industry. But besides accommodating all these special problems, day-to-day procedures must be simple enough to fit in with industrial conditions. Many of the 58 papers presented at the Symposium emphasized that records, checks, measurements and handling precautions, if suitably devised, provide the control vital to efficient operation, serve as checks against loss or waste of valuable materials and help meet the

  3. Proceedings of the 3rd international symposium on material chemistry in nuclear environment (MATERIAL CHEMISTRY '02)

    International Nuclear Information System (INIS)

    2003-03-01

    The volume contains all presented papers during the 3rd International Symposium on Material Chemistry in Nuclear Environment: MATERIAL CHEMISTRY 02 (MC'02), held March 13-15, 2002. The purpose of this symposium is to provide an international forum for the discussion of recent progress in the field of materials chemistry in nuclear environments. This symposium intends to build on the success of the previous symposiums held in Tsukuba in 1992 and 1996. The topics discussed in the symposium MC'02 are Chemical Reaction and Thermodynamics, Degradation Phenomena, New Characterization Technology, Fabrication and New Materials, Composite Materials, Surface Modification, and Computational Science. The 61 of the presented papers are indexed individually. (J.P.N.)

  4. Proceedings of the second international conference on advances in nuclear materials: abstract booklet and souvenir

    International Nuclear Information System (INIS)

    2011-01-01

    Nuclear materials form special class of materials which either act as fuel for the nuclear reactors or form the structure of the reactors and the allied systems. The topics covered in this conference are: materials challenges for thermal and fast reactors, technological advances in nuclear fuels and components, materials for future reactors, fuel cycles and materials challenges, materials degradation and life management, advanced materials development, modelling and simulation, advanced materials- II, advanced materials for future reactors, development of advanced fuel and structural materials, zirconium alloy developments, irradiation effects and PIE, advanced nuclear fuels, corrosion and materials characterization. Papers relevant to INIS are indexed separately

  5. Proceedings, annual meeting - Institute of Nuclear Materials Management, 21st, 1980

    International Nuclear Information System (INIS)

    Anon.

    1980-01-01

    This meeting proceedings contains 84 papers by various authors. Some of the topics discussed are: safeguards today and tomorrow; physical protection-requirements and rules; safeguards measurement technology; nonproliferation and international safeguards; analysis and interpretation of materials accounting data; physical protection; safeguards evaluation methodologies; public information; emergency response for accounting and physical security systems; materials control and accountability systems; and safeguards measurements technology. 78 papers are separately indexed

  6. New Nuclear Materials Including Non Metallic Fuel Elements. Vol. II. Proceedings of the Conference on New Nuclear Materials Technology, Including Non Metallic Fuel Elements

    International Nuclear Information System (INIS)

    1963-01-01

    One of the major aims of the International Atomic Energy Agency in furthering the peaceful uses of atomic energy is to encourage the development of economical nuclear power. Certainly, one of the more obvious methods of producing economical nuclear power is the development of economical fuels that can be used at high temperatures for long periods of time, and which have sufficient strength and integrity to operate under these conditions without permitting the release of fission products. In addition it is desirable that after irradiation these new fuels be economically reprocessed to reduce further the cost of the fuel cycle. As nuclear power becomes more and more competitive with conventional power the interest in new and more efficient higher-temperature fuels naturally increases rapidly. For these reasons, the Agency organized a Conference on New Nuclear Materials Technology, Including Non-Metallic Fuel Elements, which was held from 1 to 5 July 1963 at the International Hotel, Prague, with the assistance and co-operation of the Government of the Czechoslovak Socialist Republic. A total of 151 scientists attended, from 23 countries and 4 international organizations. The participants heard and discussed more than 60 scientific papers. The Agency wishes to thank the scientists who attended this Conference for their papers and for many spirited discussions that truly mark a successful meeting. The Agency wishes also to record its gratitude for the assistance and generous hospitality accorded the Conference, the participants and the Agency's staff by the Government of the Czechoslovak Socialist Republic and by the people of Prague. The scientific information contained in these Proceedings should help to quicken the pace of progress in the fabrication of new and m ore economical fuels, and it is hoped that these proceedings will be found useful to all workers in this and related fields

  7. Measures to prevent, intercept and respond to illicit uses of nuclear material and radioactive sources. Proceedings

    International Nuclear Information System (INIS)

    2002-01-01

    As nuclear programmes have evolved, the quantities of nuclear material in use or storage, and the number of facilities operating or shut down has increased. In particular, the dismantling of nuclear weapons has resulted in greatly increased stockpiles of weapons usable plutonium and highly enriched uranium. Concern over the security of these and related materials has been further raised by the continued occurrence of cases of illicit trafficking. The risks are theft, leading to trafficking and possible illicit use, and sabotage which could lead to the creation of radiological hazards. The challenge is threefold: prevention, detection and interception, and response. Prevention starts with effective national systems for accountancy, control and protection. Detection and interception involves effective measures to combat illicit trafficking, and response requires planning for the consequences of theft and sabotage. Responsibilities in these fields are national, but nuclear security also has a powerful international dimension. The consequences of failures in national measures reach beyond national boundaries. The effectiveness of national nuclear security can be enhanced through international measures: through agreed international norms, standards and guides, through training and advice, through information exchange and the sharing of experience, and through developing common understandings and perceptions. The Stockholm Conference contributed by focusing on the threats, including terrorist, to nuclear and other radioactive materials; on how to assess them and on how to develop the appropriate security measures. National measures to protect nuclear material and facilities and the continuing development of international standards and obligations were described. The conference discussed the patterns and trends in the illicit trafficking of nuclear and other radioactive materials and national and international measures to combat such trafficking. Finally, it considered

  8. Measures to prevent, intercept and respond to illicit uses of nuclear material and radioactive sources. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-08-01

    As nuclear programmes have evolved, the quantities of nuclear material in use or storage, and the number of facilities operating or shut down has increased. In particular, the dismantling of nuclear weapons has resulted in greatly increased stockpiles of weapons usable plutonium and highly enriched uranium. Concern over the security of these and related materials has been further raised by the continued occurrence of cases of illicit trafficking. The risks are theft, leading to trafficking and possible illicit use, and sabotage which could lead to the creation of radiological hazards. The challenge is threefold: prevention, detection and interception, and response. Prevention starts with effective national systems for accountancy, control and protection. Detection and interception involves effective measures to combat illicit trafficking, and response requires planning for the consequences of theft and sabotage. Responsibilities in these fields are national, but nuclear security also has a powerful international dimension. The consequences of failures in national measures reach beyond national boundaries. The effectiveness of national nuclear security can be enhanced through international measures: through agreed international norms, standards and guides, through training and advice, through information exchange and the sharing of experience, and through developing common understandings and perceptions. The Stockholm Conference contributed by focusing on the threats, including terrorist, to nuclear and other radioactive materials; on how to assess them and on how to develop the appropriate security measures. National measures to protect nuclear material and facilities and the continuing development of international standards and obligations were described. The conference discussed the patterns and trends in the illicit trafficking of nuclear and other radioactive materials and national and international measures to combat such trafficking. Finally, it considered

  9. Proceedings of the national workshop on nuclear forensics: fundamentals and applications - course material

    International Nuclear Information System (INIS)

    Mishra, S.; Chaudhury, Probal

    2016-01-01

    This course introduces the understanding of the nuclear/radioactive material involved either in illicit trafficking or possibility of getting involved in nuclear or radiological threats or incidents. It will also highlight the basics of nuclear forensics involving various steps i.e categorization, characterization, interpretation and finally the reconstruction of the nuclear/radiological scenario. This will also provide a platform for discussing the challenges and opportunities associated with such investigations. Various techniques adopted throughout the globe for the characterization of nuclear/radioactive materials for nuclear/radiological forensic investigations involving destructive, non-destructive assay methodologies along with traditional forensic analysis will be discussed. The international cooperation which is an indispensable part for nuclear forensic investigation and nuclear forensics support at IAEA will also be discussed in the forum. Apart from this the applications of the techniques in safeguards and other frameworks will also be a part of this workshop. For understanding of the participants about the subject, a table top exercise will be conducted along with demonstration of different radiation detection systems. This manual will serve as a post course reference. Papers relevant to INIS are indexed separately

  10. Physical protection of nuclear materials: Experience in regulation, implementation and operations. Proceedings of a conference

    International Nuclear Information System (INIS)

    1998-01-01

    The conference was held at IAEA Headquarters in Vienna from 10 to 14 November 1997. It was attended by 162 registered participants from 42 countries and eight international organizations. The 58 papers presented dealt with the experience of regulators, designers and facility operators, including response forces, in meeting the demands and requirements in this changing area of physical protection of nuclear materials and facilities. Individual abstracts were prepared for each of the papers. Topics covered include contemporary and emerging issues, experience in regulation, implementation at facilities, program assessment and cooperation, hardware and software, illicit trafficking in nuclear materials, and transportation

  11. Characterization and testing of materials for nuclear reactors. Proceedings of a technical meeting

    International Nuclear Information System (INIS)

    2007-03-01

    Nuclear techniques in general and neutrons based methods in particular have played and will continue to play an important role in research in materials science and technology. Today the world is looking at nuclear fission and nuclear fusion as the main sources of energy supply for the future. Research reactors have played a key role in the development of nuclear technology. A materials development programme will thus play a major role in the design and development of new nuclear power plants, for the extension of the life of operating reactors as well as for fusion reactors. Against this background, the IAEA had organized a Technical Meeting on Development, Characterization and Testing of Materials - With Special Reference to the Energy Sector under the activity on specific applications of research reactors. The meeting was held in Vienna, May 29- June 2, 2006. There was also participation by experts in techniques, complementary to neutrons. The participants for the technical meeting were experts in the utilization of nuclear techniques namely the high flux and medium flux research reactors, fusion research and positron annihilation. They presented the design, development and utilization of the facilities at their respective centres for materials characterization with main focus on materials for nuclear energy, both fission and fusion. In core irradiation of materials, development of instrument for residual stress measurement in large and / or irradiated specimen, neutron radiography for inspection of irradiated fuel, work on oxide dispersion strengthened (ODS) steels and SiC composites, relevant to future power systems were cited as application of nuclear techniques in fission reactors. The use of neutron scattering for helium bubbles in steel, application of positron annihilation to study helium bubbles in Cu, Ti-stabilized stainless steel and voidswelling studies etc. show that these techniques have an important role in the development of materials for energy

  12. Proceedings of the Tripartite Seminar on Nuclear Material Accounting and Control at Radiochemical Plants

    International Nuclear Information System (INIS)

    1999-01-01

    The problems of creation and operation of nuclear materials (NM) control and accounting systems and their components at radiochemical plants were discussed in seminar during November 2-6 of 1998. There were 63 Russian and 25 foreign participants in seminar. The seminar programme includes following sessions and articles: the aspects of State NM control and accountancy; NM control and accounting in radiochemical plants and at separate stages of reprocessing of spent nuclear fuel and irradiated fuel elements of commercial reactors; NM control and accountancy in storage facilities of radiochemical plants; NM control and accounting computerization, material balance assessment, preparation of reports; qualitative and quantitative measurements in NM control and accounting at radiochemical plants destructive analysis techniques [ru

  13. Design of training centres for nuclear power plants. Working material. Proceedings of a specialists` meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-11-01

    The purpose of this meeting was to provide an international forum for presentation and discussion of experiences in the design and operation of training centres for nuclear power plant personnel. The term ``training centre``, as used during this meeting, includes both those facilities that are dedicated to provide training for an individual nuclear power plants, and that are often located near that plant, as well as facilities that provide training for multiple NPPs, and which are operated by vendors or by utility organizations that are not directly controlled by the NPP organizations which they serve. The topic, ``design of training centres`` was used in its broadest sense to include not only facilities (such as classrooms, laboratories and simulators), but also design of: training organizations; training programmes and materials; and examination/evaluation methods. Refs, figs, tabs.

  14. Design of training centres for nuclear power plants. Working material. Proceedings of a specialists' meeting

    International Nuclear Information System (INIS)

    1996-01-01

    The purpose of this meeting was to provide an international forum for presentation and discussion of experiences in the design and operation of training centres for nuclear power plant personnel. The term ''training centre'', as used during this meeting, includes both those facilities that are dedicated to provide training for an individual nuclear power plants, and that are often located near that plant, as well as facilities that provide training for multiple NPPs, and which are operated by vendors or by utility organizations that are not directly controlled by the NPP organizations which they serve. The topic, ''design of training centres'' was used in its broadest sense to include not only facilities (such as classrooms, laboratories and simulators), but also design of: training organizations; training programmes and materials; and examination/evaluation methods. Refs, figs, tabs

  15. Nuclear Inter Jura '77 Proceedings

    International Nuclear Information System (INIS)

    1977-01-01

    These Proceedings of the Third Congress of the International Nuclear Law Association reproduce the papers presented in their original language with an abstract in English as well as the ensuing discussions. A majority of the papers have been translated into English for the Proceedings. The subjects dealt with respectively concerned contractual aspects of nuclear activities, the impact of nuclear power on the environment and public acceptance, radiological protection, third party liability and insurance, harmonisation of licensing regulations, export of nuclear equipment in relation to the Non-Proliferation Treaty and finally, computerization of nuclear law. (NEA) [fr

  16. Progress report on nuclear science and technology in China (Vol.1). Proceedings of academic annual meeting of China Nuclear Society in 2009, No.4--nuclear material

    International Nuclear Information System (INIS)

    2010-11-01

    Progress report on nuclear science and technology in China (Vol. 1) includes 889 articles which are communicated on the first national academic annual meeting of China Nuclear Society. There are 10 books totally.This is the fourth one, the content is about nuclear materials, isotope separation, nuclear chemistry and radiological chemistry.

  17. Nuclear materials

    International Nuclear Information System (INIS)

    1996-01-01

    In 1998, Nuclear Regulatory Authority of the Slovak Republic (NRA SR) performed 38 inspections, 25 of them were performed in co-operation with IAEA inspectors. There is no fresh nuclear fuel at Bohunice A-1 NPP at present. Fresh fuel of Bohunice V-1 and V-2 NPPs is inspected in the fresh fuel storage.There are 327 fresh fuel assemblies in Mochovce NPP fresh fuel storage. In addition to that, are also 71 small users of nuclear materials in Slovakia. In most cases they use: covers made of depleted uranium for non-destructive works, detection of level in production plants, covers for therapeutical sources at medical facilities. In. 1995, NRA SR issued 4 new licences for nuclear material withdrawal. In the next part manipulation with nuclear materials, spent fuel stores and illegal trafficking in nuclear materials are reported

  18. Nuclear Inter Jura'87 Proceedings

    International Nuclear Information System (INIS)

    1988-01-01

    The Proceedings of the 8. Congress of the International Nuclear Law Association (INLA) contain the papers presented at the Congress and the ensuing discussions. The following topics were dealt with: new orientations of nuclear law - its convergence and discordance with other fields of law; impact of international treaties; comparison with legal provisions of other high-technology sectors and optimization of nuclear law. Finally, the last session examined the Chernobyl accident and the legal gaps it revealed. (NEA) [fr

  19. Diagnostic systems in nuclear power plants. Proceedings of a technical committee meeting. Working material

    International Nuclear Information System (INIS)

    1998-01-01

    Nuclear power industry has a quite long tradition in on-line diagnostic of mechanical components and a considerable effort was put in developing diagnostic systems which are able to detect arising mechanical problems at an early stage. Computers are increasingly exploited to provide higher level information on process behaviour such as: early indication of the process deviation from normal conditions; rapid identification of the cause of any disturbance; prediction of the evolution of a disturbance; operator aid through computerized help. Following the recommendation of Several Member States to strengthen the activity in this field two divisions of IAEA established in 1995 the International Task Force on Nuclear Power Plant Diagnostics. The scope of the task force cover both technological developments and safety/licensing aspects of diagnostics. This report contains papers presented at the last in the series of Technical Committee Meetings on the Diagnostic Systems in Nuclear Power Plants organized in the framework of International Task Force

  20. Diagnostic systems in nuclear power plants. Proceedings of a technical committee meeting. Working material

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-31

    Nuclear power industry has a quite long tradition in on-line diagnostic of mechanical components and a considerable effort was put in developing diagnostic systems which are able to detect arising mechanical problems at an early stage. Computers are increasingly exploited to provide higher level information on process behaviour such as: early indication of the process deviation from normal conditions; rapid identification of the cause of any disturbance; prediction of the evolution of a disturbance; operator aid through computerized help. Following the recommendation of Several Member States to strengthen the activity in this field two divisions of IAEA established in 1995 the International Task Force on Nuclear Power Plant Diagnostics. The scope of the task force cover both technological developments and safety/licensing aspects of diagnostics. This report contains papers presented at the last in the series of Technical Committee Meetings on the Diagnostic Systems in Nuclear Power Plants organized in the framework of International Task Force Refs, figs, tabs

  1. Collective nuclear dynamics. Proceedings

    International Nuclear Information System (INIS)

    Ivanyuk, F.A.

    1994-01-01

    The Fourth International school on nuclear physics was help on 29 Aug - 7 Sep, 1994 in Ukraine. The specialists discussed following subjects:liquid drop and the shell correction method; nuclear deformation energy and fission; nuclear structure at high spins, superdeformed states, structure of excited and exotic nuclei; nuclear fluid dynamics and large scale collective motion; order and chaos as they relate to the collective motion; quantum and interference phenomena in nuclear collisions; quasi-fission and multinucleon fragmentation effects; shell effects in non-nuclear systems; new nuclear facilities

  2. Collective nuclear dynamics. Proceedings.

    Energy Technology Data Exchange (ETDEWEB)

    Ivanyuk, F A [eds.

    1994-12-31

    The Fourth International school on nuclear physics was help on 29 Aug - 7 Sep, 1994 in Ukraine. The specialists discussed following subjects:liquid drop and the shell correction method; nuclear deformation energy and fission; nuclear structure at high spins, superdeformed states, structure of excited and exotic nuclei; nuclear fluid dynamics and large scale collective motion; order and chaos as they relate to the collective motion; quantum and interference phenomena in nuclear collisions; quasi-fission and multinucleon fragmentation effects; shell effects in non-nuclear systems; new nuclear facilities.

  3. Materials for advanced power engineering 2010. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Lecomte-Beckers, Jacqueline; Contrepois, Quentin; Beck, Tilmann; Kuhn, Bernd [eds.

    2010-07-01

    The 9th Liege Conference on ''Materials for Advanced Power Engineering'' presents the results of the materials related COST Actions 536 ''Alloy Development for Critical Components of Environmentally Friendly Power Plants'' and 538 ''High Temperature Plant Lifetime Extension''. In addition, the broad field of current materials research perspectives for high efficiency, low- and zero- emission power plants and new energy technologies for the next decades are reported. The Conference proceedings are structured as follows: 1. Materials for advanced steam power plants; 2. Gas turbine materials; 3. Materials for nuclear fission and fusion; 4. Solid oxide fuel cells; 5. Corrosion, thermomechanical fatigue and modelling; 6. Zero emission power plants.

  4. Materials for advanced power engineering 2010. Proceedings

    International Nuclear Information System (INIS)

    Lecomte-Beckers, Jacqueline; Contrepois, Quentin; Beck, Tilmann; Kuhn, Bernd

    2010-01-01

    The 9th Liege Conference on ''Materials for Advanced Power Engineering'' presents the results of the materials related COST Actions 536 ''Alloy Development for Critical Components of Environmentally Friendly Power Plants'' and 538 ''High Temperature Plant Lifetime Extension''. In addition, the broad field of current materials research perspectives for high efficiency, low- and zero- emission power plants and new energy technologies for the next decades are reported. The Conference proceedings are structured as follows: 1. Materials for advanced steam power plants; 2. Gas turbine materials; 3. Materials for nuclear fission and fusion; 4. Solid oxide fuel cells; 5. Corrosion, thermomechanical fatigue and modelling; 6. Zero emission power plants.

  5. On-the-job training and qualification of nuclear power plant personnel. Proceedings of a specialists' meeting. Working material

    International Nuclear Information System (INIS)

    1996-01-01

    The topic of this meeting , on-the-job training, was selected by the International Working Group on Training and Qualification of Nuclear Power Plant Personnel, during their most recent meeting in 1994. This International Working Group is made up of representatives from all Member States who have operating nuclear power plants. This Group felt that there was a need to provide a forum for exchange of information among specialists from Member States on the topic of on-the-job training, and further that the Agency should publish the proceedings of this meeting for the use of those specialists who were not able to attend. Refs, figs, tabs

  6. Structural Materials for Innovative Nuclear Systems (SMINS-3) - Workshop Proceedings, Idaho National Laboratory, Idaho Falls, United States, 7-10 October 2013

    International Nuclear Information System (INIS)

    2015-01-01

    The development of innovative nuclear systems such as Gen IV reactors or critical and subcritical transmutation systems requires a good knowledge of the properties of the materials used for designing these reactors. A common feature in developing nuclear systems is the widely recognised need for experimental programmes to select and characterise structural materials. Structural materials research, both at national and international level, can significantly contribute to the future deployment of new systems. Since 2007, the OECD Nuclear Energy Agency Nuclear Science Committee organises a series of workshop on Structural Materials for Innovative Nuclear Systems (SMINS) to stimulate an exchange of information on current materials research programmes for innovative nuclear systems with a view to identifying and developing potential synergies. The third workshop was held on 7-10 October 2013 in Idaho Falls (United States) and organised through the collaboration of the Working Party on Scientific Issues of the Fuel Cycle (WPFC) and the Working Party on Multi-Scale Modelling of Fuels and Structural Materials for Nuclear Systems (WPMM) in co-operation with the European Community (EC) and the International Atomic Energy Agency (IAEA). A total of 74 abstracts were received for either an oral and poster presentation. These proceedings include the papers presented at the workshop

  7. Institute of Nuclear Materials Management 36. annual meeting: Proceedings. Volume 24

    International Nuclear Information System (INIS)

    Anon.

    1995-01-01

    The sessions at this meeting covered the following topics: international safeguards; physical protection; material control and accountability (MC and A) training; waste overview; nonproliferation and arms control -- US/former Soviet Union; MC and A/physical protection -- SNM storage; spent fuel storage; physical protection -- intrusion sensors and access delay; MC and A -- gamma ray and holdup measurements; MC and A -- neutron based measurements; MC and A/nonproliferation and arms control -- fissile materials disposition; low level waste; packaging and transportation; international safeguards and nonproliferation and arms control -- IAEA verification in the US; international safeguards and physical protection -- video systems; poster and demonstrations; international safeguards and physical protection -- T.I.D.'s, tags and seals; high level wastes and mixed waste; MC and A -- bulk measurements; MC and A and physical protection -- policy; nonproliferation and arms control -- detection and monitoring techniques; nonproliferation and arms control -- US-Russian lab-to-lab safeguards cooperation; MC and A -- information systems; physical protection and MC and A -- vulnerability assessments; waste management -- measurement; international safeguards -- integrated and remote monitoring systems; MC and A -- material control and accountability and indicators; nonproliferation and arms control -- treaties and analysis; nonproliferation and arms control -- plutonium/HEU nonproliferation; MC and A -- measurement control and verification; and international safeguards and nonproliferation and arms control -- environmental monitoring and export control. Separate abstracts were prepared for some of the papers in this volume

  8. Advanced materials and technologies. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Lindroos, V K; Alander, T K.R. [eds.; Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Physical Metallurgy and Materials Science

    1996-12-31

    The contents of the proceedings consist of three chapters, of which, the first discusses common megatrends, both nationally and globally, in different fields of materials technology. The second chapter is dealing with novel production and processing of base metals and, finally, the third chapter is related with current achievements and future goals of electronic, magnetic, optical and coating materials and their processing

  9. Advanced materials and technologies. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Lindroos, V.K.; Alander, T.K.R. [eds.] [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Physical Metallurgy and Materials Science

    1995-12-31

    The contents of the proceedings consist of three chapters, of which, the first discusses common megatrends, both nationally and globally, in different fields of materials technology. The second chapter is dealing with novel production and processing of base metals and, finally, the third chapter is related with current achievements and future goals of electronic, magnetic, optical and coating materials and their processing

  10. The nuclear review. Proceedings

    International Nuclear Information System (INIS)

    Dimson, E.; Staunton, M.; Jeffrey, R.; Robinson, C.; O'Neill, M.

    1995-01-01

    Four contributions to a seminar held in February 1995 at the University of Surrey on the hearings for the government's review of the future role of nuclear generated electricity in the United Kingdom are brought together in this document. They provide analysis and policy recommendations from the standpoint of the nuclear industry, the political opposition and the academic world. Separate abstracts have been prepared for each paper. (UK)

  11. Proceedings of the ANS executive conference on international nuclear commerce

    International Nuclear Information System (INIS)

    Anon.

    1980-01-01

    These proceedings compile papers given at a conference on nuclear commerce. Topice include: global forecasting, foreign policy, nuclear weapons proliferation, trade, non-proliferation policies, non-proliferation treaties, IAEA safeguards, international cooperation, nuclear materials management and safety, the nuclear power industry and energy policy, plutonium storage, and uranium enrichment

  12. New Nuclear Materials Including Non Metallic Fuel Elements. Vol. I. Proceedings of the Conference on New Nuclear Materials Technology, Including Non Metallic Fuel Elements

    International Nuclear Information System (INIS)

    1963-01-01

    One of the major aims of the International Atomic Energy Agency in furthering the peaceful uses of atomic energy is to encourage the development of economical nuclear power. Certainly, one of the more obvious methods of producing economical nuclear power is the development of economical fuels that can be used at high temperatures for long periods of time, and which have sufficient strength and integrity to operate under these conditions without permitting the release of fission products. In addition it is desirable that after irradiation these new fuels be economically reprocessed to reduce further the cost of the fuel cycle. As nuclear power becomes more and more competitive with conventional power the interest in new and more efficient higher-temperature fuels naturally increases rapidly. For these reasons, the Agency organized a Conference on New Nuclear Materials Technology, Including Non-Metallic Fuel Elements, which was held from 1 to 5 July 1963 at the International Hotel, Prague, with the assistance and co-operation of the Government of the Czechoslovak Socialist Republic. A total of 151 scientists attended, from 23 countries and 4 international organizations. The participants heard and discussed more than 60 scientific papers

  13. International training course on implementation of state systems of accounting for and control of nuclear materials: proceedings

    International Nuclear Information System (INIS)

    1984-06-01

    This report incorporates all lectures and presentations at the International Training Course on Implementation of State Systems of Accounting for and Control of Nuclear Materials held October 17 through November 4, 1983, at Santa Fe and Los Alamos, New Mexico and Richland, Washington, USA. Authorized by the US Nuclear Non-Proliferation Act and sponsored by the US Department of Energy in cooperation with the International Atomic Energy Agency, the course was developed to provide practical training in the design, implementation, and operation of a State system of nuclear materials accountability and control that satisfies both national and international safeguards requirements. Major emphasis for the 1983 course was placed on safeguards methods used at bulk-handling facilities, particularly low-enriched uranium conversion and fuel fabrication plants. The course was conducted by the University of California's Los Alamos National Laboratory and Exxon Nuclear Company, Inc. Tours and demonstrations were arranged at the Los Alamos National Laboratory, Los Alamos, New Mexico, and the Exxon Nuclear fuel fabrication plant, the Battelle Pacific Northwest Laboratory, Westinghouse Fast Flux Test Facility Visitor Center, and Washington Public Power System nuclear reactor facilities in Richland, Washington. Individual presentations were indexed for inclusion in the Energy Data Base

  14. International training course on implementation of state systems of accounting for and control of nuclear materials: proceedings

    Energy Technology Data Exchange (ETDEWEB)

    1984-06-01

    This report incorporates all lectures and presentations at the International Training Course on Implementation of State Systems of Accounting for and Control of Nuclear Materials held October 17 through November 4, 1983, at Santa Fe and Los Alamos, New Mexico and Richland, Washington, USA. Authorized by the US Nuclear Non-Proliferation Act and sponsored by the US Department of Energy in cooperation with the International Atomic Energy Agency, the course was developed to provide practical training in the design, implementation, and operation of a State system of nuclear materials accountability and control that satisfies both national and international safeguards requirements. Major emphasis for the 1983 course was placed on safeguards methods used at bulk-handling facilities, particularly low-enriched uranium conversion and fuel fabrication plants. The course was conducted by the University of California's Los Alamos National Laboratory and Exxon Nuclear Company, Inc. Tours and demonstrations were arranged at the Los Alamos National Laboratory, Los Alamos, New Mexico, and the Exxon Nuclear fuel fabrication plant, the Battelle Pacific Northwest Laboratory, Westinghouse Fast Flux Test Facility Visitor Center, and Washington Public Power System nuclear reactor facilities in Richland, Washington. Individual presentations were indexed for inclusion in the Energy Data Base.

  15. Materials for advanced power engineering 2010. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Lecomte-Beckers, Jacqueline; Contrepois, Quentin; Beck, Tilmann; Kuhn, Bernd (eds.)

    2010-07-01

    The 9th Liege Conference on ''Materials for Advanced Power Engineering'' presents the results of the materials related COST Actions 536 ''Alloy Development for Critical Components of Environmentally Friendly Power Plants'' and 538 ''High Temperature Plant Lifetime Extension''. In addition, the broad field of current materials research perspectives for high efficiency, low- and zero- emission power plants and new energy technologies for the next decades are reported. The Conference proceedings are structured as follows: 1. Materials for advanced steam power plants; 2. Gas turbine materials; 3. Materials for nuclear fission and fusion; 4. Solid oxide fuel cells; 5. Corrosion, thermomechanical fatigue and modelling; 6. Zero emission power plants.

  16. International training course on implementation of state systems of accounting for and control of nuclear materials: proceedings

    International Nuclear Information System (INIS)

    1986-06-01

    This report incorporates all lectures and presentations at the International Training Course on Implementation of State Systems of Accounting for and Control of Nuclear Materials held June 3 through June 21, 1985, at Santa Fe and Los Alamos, New Mexico, and San Clemente, California. Authorized by the US Nuclear Non-Proliferation Act and sponsored by the US Department of Energy in cooperation with the International Atomic Energy Agency, the Course was developed to provide practical training in the design, implementation, and operation of a state system of nuclear materials accountability and control that satisfies both national and international safeguards requirements. Major emphasis for the 1985 course was placed on safeguards methods used at item-control facilities, particularly nuclear power generating stations and test reactors. An introduction to safeguards methods used at bulk handling facilities, particularly low-enriched uranium conversion and fuel fabrication plants, was also included. The course was conducted by the University of California's Los Alamos National Laboratory and the Southern California Edison Company. Tours and demonstrations were arranged at the Los Alamos National Laboratory, Los Alamos, New Mexico, and the San Onofre Nuclear Generating Station, San Clemente, California

  17. International training course on implementation of state systems of accounting for and control of nuclear materials: proceedings

    Energy Technology Data Exchange (ETDEWEB)

    1986-06-01

    This report incorporates all lectures and presentations at the International Training Course on Implementation of State Systems of Accounting for and Control of Nuclear Materials held June 3 through June 21, 1985, at Santa Fe and Los Alamos, New Mexico, and San Clemente, California. Authorized by the US Nuclear Non-Proliferation Act and sponsored by the US Department of Energy in cooperation with the International Atomic Energy Agency, the Course was developed to provide practical training in the design, implementation, and operation of a state system of nuclear materials accountability and control that satisfies both national and international safeguards requirements. Major emphasis for the 1985 course was placed on safeguards methods used at item-control facilities, particularly nuclear power generating stations and test reactors. An introduction to safeguards methods used at bulk handling facilities, particularly low-enriched uranium conversion and fuel fabrication plants, was also included. The course was conducted by the University of California's Los Alamos National Laboratory and the Southern California Edison Company. Tours and demonstrations were arranged at the Los Alamos National Laboratory, Los Alamos, New Mexico, and the San Onofre Nuclear Generating Station, San Clemente, California.

  18. Proceedings of the nuclear safety seminar, 2011

    International Nuclear Information System (INIS)

    Amin S Zarkasih; Dhandang P; Rohadi A; Djarwani; Santoso; Abdul Waris; Zaki Su'ud; Sihana; Heryudo Kusumo; Yusri Heni; Yus Rusdian; Judi Pramono; Amil Mardha

    2011-06-01

    The Proceedings of the nuclear safety seminar by Nuclear Energy Regulatory Agency with the theme of strengthening in nuclear safety control, nuclear security and nuclear safeguard to Introduction of Nuclear Power Plant (NPP) in Indonesia held on Jakarta 27-28 June 2011. The seminar is an annual routine activities which organized by Nuclear Energy Regulatory Agency (BAPETEN) as an exchange for information from scientists and researchers for using nuclear technology. The proceeding consist of 4 articles from keynotes’ speaker and 39 articles from BAPETEN, BATAN and outside participants. (PPIKSN)

  19. Applications of Research Reactors Towards Research on Materials for Nuclear Fusion Technology. Proceedings of a Technical Meeting

    International Nuclear Information System (INIS)

    2013-11-01

    Controlled nuclear fusion is widely considered to represent a nearly unlimited source of energy. Recent progress in the quest for fusion energy includes the design and current construction of the International Thermonuclear Experimental Reactor (ITER), for which a licence has recently been obtained as a first of its kind fusion nuclear installation. ITER is designed to demonstrate the scientific and technological feasibility of fusion energy production in excess of 500 MW for several consecutive minutes. ITER, however, will not be able to address all the nuclear fusion technology issues associated with the design, construction and operation of a commercial fusion power plant. The demonstration of an adequate tritium or fuel breeding ratio, as well as the development, characterization and testing of structural and functional materials in an integrated nuclear fusion environment, are examples of issues for which ITER is unable to deliver complete answers. To fill this knowledge gap, several facilities are being discussed, such as the International Fusion Materials Irradiation Facility and, eventually, a fusion demonstration power plant (DEMO). However, for these facilities, a vast body of preliminary research remains to be performed, for instance, concerning the preselection and testing of suitable materials able to withstand the high temperature and pressure, and intense radiation environment of a fusion reactor. Given their capacity for material testing in terms of available intense neutron fluxes, dedicated irradiation facilities and post-irradiation examination laboratories, high flux research reactors or material test reactors (MTRs) will play an indispensable role in the development of fusion technology. Moreover, research reactors have already achieved an esteemed legacy in the understanding of material properties and behaviour, and the knowledge gained from experiments in fission materials in certain cases can be applied to fusion systems, particularly those

  20. Nuclear Energy in Central Europe 98, Proceedings

    International Nuclear Information System (INIS)

    Ravnik, M.; Jencic, I.; Zagar, T.

    1998-01-01

    Regional Meeting for Nuclear Energy in Central Europe is an annual meeting of the Nuclear Society of Slovenia. The proceedings contain 63 articles from Slovenia, sorounding countries and countries of the Central and Eastern European Region. Topics are: Research Reactors, Nuclear Methods, Reactor Physics, Thermal Hydraulics, Structural Analysis, Probabilistic Safety Assessment, Severe Accidents, NPP Operation and Nuclear Waste disposal

  1. Proceedings of the Third Scientific Presentation on Nuclear Fuel Cycle

    International Nuclear Information System (INIS)

    1998-02-01

    The proceeding contains papers presented in the Third Scientific Presentation on nuclear Fuel Element Cycle held on 4-5 Nov 1997 in Jakarta, Indonesia. These papers were divided by three groups that are technology of exploration, processing, purification and analysis of nuclear materials; technology of nuclear fuel elements and structures; and technology of waste management, safety and nuclear fuel cycle. There are 38 papers indexed individually. (ID)

  2. Annual meeting on nuclear technology 2005. Proceedings

    International Nuclear Information System (INIS)

    2005-03-01

    The proceedings of the annual meeting on nuclear technology 2005 covers the following issues: (1) reactor physics and methods of calculation: design and transients; method development and validation; (2): thermodynamics and fluid dynamics: analytical thermohydraulics for existing reactors; experiments and operational behavior; analytical methods for innovative reactors; (3) Safety of nuclear installations - methods, analysis, results: special problems; PSA and in-vessel phenomena; ex-vessel phenomena; (4) front end and back end of the fuel cycle, radioactive waste, storage: intermediate storage of fuel elements, waste treatment, (5) fuel elements and core components: fuel elements, new methods in the interpretation, manufacturing and service; (6) operation of nuclear installations: experience with the operation of NPPs; management systems, digital instrumentation and control of NPPs revision management; (7) decommissioning of nuclear installations: concepts and strategies for decommissioning and dismantling; experiences with decommissioning projects; (8) fusion technology: fusion facilities; materials and test facility; cryo technique and simulations; (9) research reactors: building new and backfitting of existing research reactors; current development; dismantling of research reactors; (10) advanced reactor concepts, energy systems, energy economics; (11) communication with the public; (12) component materials, fabrication and service behavior: degradation effects of component materials; component behavior; (13): radiation protection: PSA and in-vessel phenomena, ex-vessel phenomena.

  3. Thermodynamics. Vol. II. Proceedings of the Symposium on Thermodynamics with Emphasis on Nuclear Materials and Atomic Transport in Solids

    International Nuclear Information System (INIS)

    1966-01-01

    Knowledge of the thermodynamics of nuclear materials is vital to the design of reactor fuels and moderating and cooling systems, in fact all facets of nuclear plant operation that involve mixtures of, or contact between, two or more elements in single- or multi-phase systems. The steep thermal gradients and the high temperatures involved in nuclear technology pose special problems for engineers and thermodynamicists, who have found that extrapolation of low-temperature data to high temperatures very often proves invalid. For this reason, standard thermodynamic techniques such as calorimetry and EMF-methods have been extended into high-temperature regions. Since the Agency's last conference on this subject, also held in Vienna (Thermodynamics of Nuclear Materials, 1962), there have been notable advances in calorimetry performed at temperatures greater than 1000°C, and in the use of EMF cells with solid electrolytes operated at similar temperatures. Significant advances have also been made in measuring diffusion parameters at the higher temperatures. An important field covered in this Symposium was the correlation of such atomic transport data with thermodynamic data, a prerequisite if the nuclear engineer is to incorporate diffusion results into his normal process- assessment techniques. Finally the Symposium suggested the requirements for good critical tables. The mere compiling of such data is no longer sufficient; the compiler must have free access to all the data of a particular experiment, he must have an intimate knowledge of experimental work in this field and he must weight every figure quoted in the light of his experience. As a step in this direction, the Agency has called on the services of many well-known experts and is preparing a number of monographs giving critical assessments of thermodynamic data and phase-diagrams for many of the elements of interest in reactor design. Most of the countries engaged in research in thermodynamics were represented at

  4. Thermodynamics. Vol. II. Proceedings of the Symposium on Thermodynamics with Emphasis on Nuclear Materials and Atomic Transport in Solids

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1966-02-15

    Knowledge of the thermodynamics of nuclear materials is vital to the design of reactor fuels and moderating and cooling systems, in fact all facets of nuclear plant operation that involve mixtures of, or contact between, two or more elements in single- or multi-phase systems. The steep thermal gradients and the high temperatures involved in nuclear technology pose special problems for engineers and thermodynamicists, who have found that extrapolation of low-temperature data to high temperatures very often proves invalid. For this reason, standard thermodynamic techniques such as calorimetry and EMF-methods have been extended into high-temperature regions. Since the Agency's last conference on this subject, also held in Vienna (Thermodynamics of Nuclear Materials, 1962), there have been notable advances in calorimetry performed at temperatures greater than 1000 Degree-Sign C, and in the use of EMF cells with solid electrolytes operated at similar temperatures. Significant advances have also been made in measuring diffusion parameters at the higher temperatures. An important field covered in this Symposium was the correlation of such atomic transport data with thermodynamic data, a prerequisite if the nuclear engineer is to incorporate diffusion results into his normal process- assessment techniques. Finally the Symposium suggested the requirements for good critical tables. The mere compiling of such data is no longer sufficient; the compiler must have free access to all the data of a particular experiment, he must have an intimate knowledge of experimental work in this field and he must weight every figure quoted in the light of his experience. As a step in this direction, the Agency has called on the services of many well-known experts and is preparing a number of monographs giving critical assessments of thermodynamic data and phase-diagrams for many of the elements of interest in reactor design. Most of the countries engaged in research in thermodynamics were

  5. Thermodynamics. Vol. I. Proceedings of the Symposium on Thermodynamics with Emphasis on Nuclear Materials and Atomic Transports in Solids

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1966-01-15

    Knowledge of the thermodynamics of nuclear materials is vital to the design of reactor fuels and moderating and cooling systems, in fact all facets of nuclear plant operation that involve mixtures of, or contact between, two or more elements in single- or multi-phase systems. The steep thermal gradients and the high temperatures involved in nuclear technology pose special problems for engineers and thermodynamicists, who have found that extrapolation of low-temperature data to high temperatures very often proves invalid. For this reason, standard thermodynamic techniques such as calorimetry and EMF-methods have been extended into high-temperature regions. Since the Agency's last conference on this subject, also held in Vienna (Thermodynamics of Nuclear Materials, 1962), there have been notable advances in calorimetry performed at temperatures greater than 1000 Degree-Sign C, and in the use of EMF cells with solid electrolytes operated at similar temperatures. Significant advances have also been made in measuring diffusion parameters at the higher temperatures. An important field covered in this Symposium was the correlation of such atomic transport data with thermodynamic data, a prerequisite if the nuclear engineer is to incorporate diffusion results into his normal process- assessment techniques. Finally the Symposium suggested the requirements for good critical tables. The mere compiling of such data is no longer sufficient; the compiler must have free access to all the data of a particular experiment, he must have an intimate knowledge of experimental work in this field and he must weight every figure quoted in the light of his experience. As a step in this direction, the Agency has called on the services of many well-known experts and is preparing a number of monographs giving critical assessments of thermodynamic data and phase-diagrams for many of the elements of interest in reactor design. Most of the countries engaged in research in thermodynamics were

  6. International Conference Nuclear Energy in Central Europe 99, V. 2. Proceedings. Embedded Meeting Neutron Imaging Methods to Detect Defects in Materials

    International Nuclear Information System (INIS)

    Gortnar, O.; Stritar, A.

    1999-01-01

    International Conference Nuclear Energy in Central Europe is an annual meeting of the Nuclear Society of Slovenia. The second book of proceedings contain 14 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region. Topics cover Neutron Imaging Methods

  7. Proceedings of the 1. General Congress of Nuclear Energy. v. 1

    International Nuclear Information System (INIS)

    1986-01-01

    The proceedings of 1 General Congress of Nuclear Energy are presented. All fields related to nuclear energy are enclosed. In the first part the following fields are shown: safety analysis, science and technology of materials, nuclear materials, nuclear laws, education and trainning, reactor physics, nuclear physics, quality assurance, mathematical models, reactor operation, safeguards, advanced technologies, thermohydraulic and reactor licensing. (M.C.K.) [pt

  8. Experience in monitoring ageing phenomena for improving nuclear power plant availability. Proceedings of a specialists' meeting. Working material

    International Nuclear Information System (INIS)

    1992-01-01

    For more than thirty years nuclear power plants have been supplying electricity to national grids. Today, the nuclear power community is facing great challenges. The safe, reliable operation of existing nuclear power plants (NPPs) must continue to be ensured. From an economic viewpoint, because of the long lead times associated with bringing new plants into service, securing the continued operation of existing plants for their planned lifetimes and possible life extension will be very important in the near term for meeting electrical power demands. The IAEA programmes in nuclear power plant ageing and life extension and in control and instrumentation promote technical information exchange between Member States with new programmes, offers assistance to Member States with an interest in reliability of NPP components, in-service inspection methods and programmes using on-line techniques, component monitoring and special technological topics of nuclear reactors. Significant experience already exists in the nuclear industry in developing and applying the monitoring techniques for different nuclear power plant applications, especially in monitoring of ageing phenomena for improving NPP availability. The purpose of this Specialists' Meeting was to bring together experts from operations, design, research and development and licensing to share their experience in: ageing mechanics of key structural components, methods of monitoring such ageing, tools for cost-effective implementation of the methods and methodologies, life management approaches and examples from current reactors, future direction for monitoring of key structural components in nuclear power plants. The meeting was organized by the IAEA International Working Groups on Life Management of Nuclear Power Plants (IWG-LMNPP) and Nuclear Power Plant Control and Instrumentation (TWG-NPPCI) in co-operation with the Czechoslovak Atomic Energy Commission and Skoda concern. Around 40 participants from 10 countries

  9. Experience in monitoring ageing phenomena for improving nuclear power plant availability. Proceedings of a specialists' meeting. Working material

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-07-01

    For more than thirty years nuclear power plants have been supplying electricity to national grids. Today, the nuclear power community is facing great challenges. The safe, reliable operation of existing nuclear power plants (NPPs) must continue to be ensured. From an economic viewpoint, because of the long lead times associated with bringing new plants into service, securing the continued operation of existing plants for their planned lifetimes and possible life extension will be very important in the near term for meeting electrical power demands. The IAEA programmes in nuclear power plant ageing and life extension and in control and instrumentation promote technical information exchange between Member States with new programmes, offers assistance to Member States with an interest in reliability of NPP components, in-service inspection methods and programmes using on-line techniques, component monitoring and special technological topics of nuclear reactors. Significant experience already exists in the nuclear industry in developing and applying the monitoring techniques for different nuclear power plant applications, especially in monitoring of ageing phenomena for improving NPP availability. The purpose of this Specialists' Meeting was to bring together experts from operations, design, research and development and licensing to share their experience in: ageing mechanics of key structural components, methods of monitoring such ageing, tools for cost-effective implementation of the methods and methodologies, life management approaches and examples from current reactors, future direction for monitoring of key structural components in nuclear power plants. The meeting was organized by the IAEA International Working Groups on Life Management of Nuclear Power Plants (IWG-LMNPP) and Nuclear Power Plant Control and Instrumentation (TWG-NPPCI) in co-operation with the Czechoslovak Atomic Energy Commission and Skoda concern. Around 40 participants from 10 countries.

  10. Proceedings of Seminar on Nuclear Geology and Mining Resources

    International Nuclear Information System (INIS)

    Zulkarnain, Iskandar; Soeprapto; Soetarno, Djoko; H, Johan-Baratha; Effendi, Amir; Widiyanta; Arief, Erni-Rifandriah; Supriyadi; Yusron, Hari

    2004-01-01

    The proceedings contains the result research and development on nuclear geology and mining resources by the center for development of nuclear ore-National Nuclear Energy Agency, Indonesia. The proceedings consist of nuclear mining activity, exploration/exploitation mining mineral and processing, and environmental process. The proceedings consists of one article from keynote speaker and 22 articles from BATAN participants. (PPIN)

  11. Computerized reactor protection and safety related systems in nuclear power plants. Proceedings of a specialists' meeting. Working material

    International Nuclear Information System (INIS)

    1998-01-01

    Though the majority of existing control and protection systems in nuclear power plants use old analogue technology and design philosophy, the use of computers in safety and safety related systems is becoming a current practice. The Specialists Meeting on ''Computerized Reactor Protection and Safety Related Systems in Nuclear Power Plants'' was organized by IAEA (jointly by the Division of Nuclear Power and the Fuel Cycle and the Division of Nuclear Installation Safety), in co-operation with Paks Nuclear Power Plant in Hungary and was held from 27-29 October 1997 in Budapest, Hungary. The meeting focused on computerized safety systems under refurbishment, software reliability issues, licensing experiences and experiences in implemented computerized safety and safety related systems. Within a meeting programme a technical visit to Paks NPP was organized. The objective of the meeting was to provide an international forum for the presentation and discussion on R and D, in-plant experiences in I and C important to safety, backfits and arguments for and reservations against the digital safety systems. The meeting was attended by 70 participants from 16 countries representing NPPs and utility organizations, design/engineering, research and development, and regulatory organizations. In the course of 4 sessions 25 technical presentations were made. The present volume contains the papers presented by national delegates and the conclusions drawn from the final general discussion

  12. Proceedings of the 2004 symposium on nuclear data

    International Nuclear Information System (INIS)

    Tahara, Yoshihisa; Fukahori, Tokio

    2005-03-01

    The 2004 Symposium on Nuclear Data was held at Tokai Research Establishment, Japan Atomic Energy Research Institute (JAERI), on 11th and 12th of November 2004. Japanese Nuclear Data Committee and Nuclear Data Center, JAERI organized this symposium. In the oral sessions, presented were 19 papers on topics of nuclear data for LWR and nuclear fuel cycle, nuclear data for ADS development, experiences from use of JENDL-3.3 and requests to JENDL-4, recent cross section measurements, nuclear data for life and material sciences, and nuclear data needs and activities in the World. In the poster session, presented were 21 papers concerning experiments, evaluations, benchmark tests, applications and so on. Those presented papers are compiled in the proceedings. The 40 of the presented papers are indexed individually. (J.P.N.)

  13. Seismic evaluation of existing nuclear power plants and other facilities V. 2. Proceedings of the technical committee meeting. Working material

    International Nuclear Information System (INIS)

    2002-01-01

    The objectives of this TCM are: to review the IAEA Safety Report on Seismic Evaluation of Existing Nuclear Power Plants in order to achieve a consensus among Member States on this matter and to discuss the outlines of an IAEA Co-ordinated Research Programme on specific topics related to this subject. This volume includes presentations of the member states describing the practical approach to evaluation of seismic equipment of the existing NPPs, validation of innovative systems for earthquake protection; seismic re-evaluation of the NPPs, seismic regulations and safety standards; and other activities related to seismic safety in Member States

  14. Seismic evaluation of existing nuclear power plants and other facilities V. 2. Proceedings of the technical committee meeting. Working material

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-01-01

    The objectives of this TCM are: to review the IAEA Safety Report on Seismic Evaluation of Existing Nuclear Power Plants in order to achieve a consensus among Member States on this matter and to discuss the outlines of an IAEA Co-ordinated Research Programme on specific topics related to this subject. This volume includes presentations of the member states describing the practical approach to evaluation of seismic equipment of the existing NPPs, validation of innovative systems for earthquake protection; seismic re-evaluation of the NPPs, seismic regulations and safety standards; and other activities related to seismic safety in Member States.

  15. Seismic evaluation of existing nuclear power plants and other facilities V. 1. Proceedings of the technical committee meeting. Working material

    International Nuclear Information System (INIS)

    2002-01-01

    The objectives of this Tcm are: to review the IAEA Safety Report on Seismic Evaluation of Existing Nuclear Power Plants in order to achieve a consensus among Member States on this matter and to discuss the outlines of an IAEA Co-ordinated Research Programme on specific topics related to this subject. Today the nuclear industry relies much more on existing facilities than on the design of new ones. Nevertheless it appears that safety evaluation against external hazards is not a decreasing activity. The reason being that maintaining an acceptable level of nuclear safety requires periodic re-assessments of facilities, either because of modifications of the environment due to human activity or because of new data or new approaches in the assessment of natural hazards. In this regard, seismic re-evaluation has increasingly become a key issue for several existing nuclear facilities, including not only nuclear power plants but also other plants of the fuel cycle, as well as research reactors or laboratories. The IAEA has already supported development of engineering practices in this field by managing a Co-ordinated Research Programme, launched in 1992, on a Benchmark Study for the seismic analysis and testing of WWER 1000 type NPPs. It is now proposed to investigate other aspects of this issue. Many of these facilities were built according to older standards which did not take into account seismic hazard. Consequently, the seismic re-evaluation of existing facilities is a real challenge for earthquake engineers. In most of the cases, it is impossible to re-evaluate according to the up to date standards because entering these standards implies that some design rules are met, what is generally not the case for older facilities. In the best cases some rules exist for non nuclear buildings. In order to achieve a consensus on this matter, the IAEA intends to edit a Safety Report on 'Seismic Evaluation of existing NPPs'. The TCM will offer the opportunity to review the draft of

  16. Symposium on Nuclear Energy. Proceedings

    International Nuclear Information System (INIS)

    1981-01-01

    The energy problem poses a big challenge to a developing country like the Philippines. The development of renewable energy sources is not enough. Aware then of the limitations of these energy sources, in spite of arguments against nuclear energy we have no other recourse but to go nuclear. This symposium emphasizes the importance of energy development to attain the country's progress and discusses the pros and economics of nuclear power. (RTD)

  17. Proceedings of microwave processing of materials 3

    International Nuclear Information System (INIS)

    Beatty, R.L.

    1992-01-01

    This book contains proceedings of the third MRS Symposium on Microwave Processing of Materials. Topics covered include: Microwave Processing Overviews, Numerical Modeling Techniques, Microwave Processing System Design, Microwave/Plasma Processing, Microwave/Materials Interactions, Microwave Processing of Ceramics, Microwave Processing of Polymers, Microwave Processing of Hazardous Wastes, Microwave NDE Techniques and Dielectric Properties and Measurements

  18. Proceedings of the Scientific Meeting in Nuclear Instrumentation Engineering

    International Nuclear Information System (INIS)

    Achmad Suntoro; Rony Djokorayono; Ferry Sujatno; Utaja

    2010-11-01

    The Proceeding of the Scientific Meeting in Nuclear Instrumentation Engineering held on Nov, 30, 2010 by the Centre for Nuclear Instrumentation Engineering - National Nuclear Energy Agency. The Proceedings of the Scientific Contains 40 papers Consist of Nuclear Instrumentation Engineering for Industry, Environment, and Nuclear Facilities. (PPIKSN)

  19. 10th Australian conference on nuclear techniques of analysis. Proceedings

    International Nuclear Information System (INIS)

    1998-01-01

    These proceedings contains abstracts and extended abstracts of 80 lectures and posters presented at the 10th Australian conference on nuclear techniques of analysis hosted by the Australian National University in Canberra, Australia from 24-26 of November 1997. The conference was divided into sessions on the following topics : ion beam analysis and its applications; surface science; novel nuclear techniques of analysis, characterization of thin films, electronic and optoelectronic material formed by ion implantation, nanometre science and technology, plasma science and technology. A special session was dedicated to new nuclear techniques of analysis, future trends and developments. Separate abstracts were prepared for the individual presentation included in this volume

  20. 10th Australian conference on nuclear techniques of analysis. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    These proceedings contains abstracts and extended abstracts of 80 lectures and posters presented at the 10th Australian conference on nuclear techniques of analysis hosted by the Australian National University in Canberra, Australia from 24-26 of November 1997. The conference was divided into sessions on the following topics : ion beam analysis and its applications; surface science; novel nuclear techniques of analysis, characterization of thin films, electronic and optoelectronic material formed by ion implantation, nanometre science and technology, plasma science and technology. A special session was dedicated to new nuclear techniques of analysis, future trends and developments. Separate abstracts were prepared for the individual presentation included in this volume.

  1. Proceedings of the Third National Conference on Nuclear Physics and Techniques

    International Nuclear Information System (INIS)

    Nguyen Thanh Binh; Nguyen Nhi Dien; Tran Kim Hung; Vuong Huu Tan

    2000-01-01

    The proceedings contains 130 papers of scientists from institutes, universities, enterprises nation-wide in Vietnam. Its subjects include: nuclear physics, theoretical physics, science and technology of nuclear reactor, application of nuclear techniques in industry, agriculture, biology, medicine, geo-hydrology, environmental protection, nuclear equipment, radiation technology, material technology, waste management, ect

  2. Proceedings of submicron multiphase materials

    International Nuclear Information System (INIS)

    Baney, R.; Gilliom, L.; Hirano, S.I.; Schmidt, H.

    1992-01-01

    This book contains the papers presented at Symposium R of the spring 1992 Materials Research Society meeting held in San Francisco, California. The title of the symposium, Submicron Multiphase Materials, was selected by the organizers to encompass the realm of composite materials from those smaller than conventional fiber matrix composites to those with phase separation dimensions approaching molecular dimensions. The development of composite materials is as old as the development of materials. Humans quickly learned that, by combining materials, the best properties of each can be realized and that, in fact, synergistic effects often arise. For example, chopped straw was used by the Israelites to limit cracking in bricks. The famed Japanese samurai swords were multilayers of hard oxide and tough ductile materials. One also finds in nature examples of composite materials. These range form bone to wood, consisting of a hard phase which provides strength and stiffness and a softer phase for toughness. Advanced composites are generally thought of as those which are based on a high modulus, discontinuous, chopped or woven fiber phase and a continuous polymer phase. In multiphase composites, dimensions can range from meters in materials such as steel rod-reinforced concrete structures to angstroms. In macrophase separated composite materials, properties frequently follow the rule of mixtures with the properties approximating the arithmetic mean of the properties of each individual phase, if there is good coupling between the phases. As the phases become smaller, the surface to volume ratio grows in importance with respect to properties. Interfacial and interphase phenomena being to dominate. Surface free energies play an ever increasing role in controlling properties. In recent years, much research in materials science has been directed at multiphase systems where phase separations are submicron in at least some dimension

  3. Proceedings of the Korean Society Nuclear Medicine Autumn Meeting 2001

    International Nuclear Information System (INIS)

    2001-01-01

    This proceedings contains articles of 2001 autumn meeting of the Korean Society Nuclear Medicine. It was held on November 16-17, 2001 in Seoul, Korea. This proceedings is comprised of 6 sessions. The subject titles of session are as follows: Cancer, Physics of nuclear medicine, Neurology, Radiopharmacy and biology, Nuclear cardiology, General nuclear medicine. (Yi, J. H.)

  4. Safeguards for special nuclear materials

    International Nuclear Information System (INIS)

    Carlson, R.L.

    1979-12-01

    Safeguards, accountability, and nuclear materials are defined. The accuracy of measuring nuclear materials is discussed. The use of computers in nuclear materials accounting is described. Measures taken to physically protect nuclear materials are described

  5. Proceedings of NUCLEAR 2008 annual international conference on sustainable development through nuclear research and education

    International Nuclear Information System (INIS)

    Constantin, Marin; Turcu, Ilie

    2008-01-01

    The proceedings of the NUCLEAR 2008 annual international conference on sustainable development through nuclear research and education held at INR-Pitesti on May, 28 - 30 2008 contain 88 communications presented in 3 sections addressing the themes of Nuclear energy, Environmental protection, and Sustainable development. In turn these sections are addressing the following items: Section 1.1 - Nuclear safety and severe accidents (12 papers); Section 1.2 - Nuclear reactors (11 papers); Section 1.3 - Nuclear technologies and materials (20 papers); Section 2.1 - Radioprotection (5 papers); Section 2.2 - Radioactive waste management (20 papers); Section 2.3 - air, water and soil protection (5 papers); Section 3.1 - Strategies in energy (3 papers); Section 3.2 - Education, continuous formation and knowledge transfer (8 papers); Section 3.3 - International partnership for a sustainable development (4 papers). The conference proceedings where divided into two parts. This item refers particularly to the second part

  6. Proceedings of the nuclear safety seminar, 2013: With the spirit of togetherness we improve the synergy of nuclear power control

    International Nuclear Information System (INIS)

    Heryudo Kusumo; Judi Pramono; Amin Zarkasi; Azhar; Novijanti Noor; Sihana; Djarwani S; Syahrir; Eri Hiswara

    2013-06-01

    The Proceedings of the nuclear safety seminar was held on Jakarta 19 June 2013 by Nuclear Energy Regulatory Agency. The seminar theme of the spirit with togetherness to improve the synergy of nuclear power control in Indonesia. The presented papers in this proceeding are divided into oral and poster group as follows: 1). Safety and monitoring of radiation facilities and radioactive substances (health, industry, research, environment), and radioactive sources security. 2). Safety and control of nuclear installation and materials (reactor, research reactor, nuclear mining, process and utilization of nuclear material, radioactive waste management, introduction of NPP) and security of nuclear installation and materials. The proceeding consist of 3 handouts from keynotes’ speaker, 23 oral articles and 15 poster articles from BAPETEN, BATAN and outside participants. (PPIKSN)

  7. Safety culture in nuclear installations. Proceedings

    International Nuclear Information System (INIS)

    Carnino, A.; Weimann, G.

    1995-04-01

    These proceedings of the International Topical Meeting on Safety Culture in Nuclear Installations held in Vienna, Austria from 24 to 28 April 1995 provide a wide forum of information exchange and discussions on the topic safety culture in nuclear power plants. Safety culture deals with human factors since it deals with attitudes, organization and management. It then means that it has a natural component in it which is linked to the national culture and education. There are about 95 contributions, some of them presented by title and abstract only. All of them are in the subject scope of INIS. (Botek)

  8. Safety culture in nuclear installations. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Carnino, A [ed.; International Atomic Energy Agency, Vienna (Austria); Weimann, G [ed.; Oesterreichisches Forschungszentrum Seibersdorf GmbH (Austria)

    1995-04-01

    These proceedings of the International Topical Meeting on Safety Culture in Nuclear Installations held in Vienna, Austria from 24 to 28 April 1995 provide a wide forum of information exchange and discussions on the topic safety culture in nuclear power plants. Safety culture deals with human factors since it deals with attitudes, organization and management. It then means that it has a natural component in it which is linked to the national culture and education. There are about 95 contributions, some of them presented by title and abstract only. All of them are in the subject scope of INIS. (Botek).

  9. Mining Pribram in science and technology. Proceedings of Session U - Mineral raw materials treatment

    International Nuclear Information System (INIS)

    Tomasek, J.; Vetejska, K.

    1987-01-01

    The proceedings of session ''Mineral raw materials treatment'' contain 27 papers of which only one deals with the application of nuclear technology, namely, the effect of fast electrons on the magnetic properties of the polymetallic Rudniany ore. (J.B.)

  10. Absolute nuclear material assay

    Science.gov (United States)

    Prasad, Manoj K [Pleasanton, CA; Snyderman, Neal J [Berkeley, CA; Rowland, Mark S [Alamo, CA

    2010-07-13

    A method of absolute nuclear material assay of an unknown source comprising counting neutrons from the unknown source and providing an absolute nuclear material assay utilizing a model to optimally compare to the measured count distributions. In one embodiment, the step of providing an absolute nuclear material assay comprises utilizing a random sampling of analytically computed fission chain distributions to generate a continuous time-evolving sequence of event-counts by spreading the fission chain distribution in time.

  11. Comprehensive nuclear materials

    CERN Document Server

    Allen, Todd; Stoller, Roger; Yamanaka, Shinsuke

    2012-01-01

    Comprehensive Nuclear Materials encapsulates a panorama of fundamental information on the vast variety of materials employed in the broad field of nuclear technology. The work addresses, in five volumes, 3,400 pages and over 120 chapter-length articles, the full panorama of historical and contemporary international research in nuclear materials, from Actinides to Zirconium alloys, from the worlds' leading scientists and engineers. It synthesizes the most pertinent research to support the selection, assessment, validation and engineering of materials in extreme nuclear environments. The work discusses the major classes of materials suitable for usage in nuclear fission, fusion reactors and high power accelerators, and for diverse functions in fuels, cladding, moderator and control materials, structural, functional, and waste materials.

  12. Proceedings of the second workshop on polarised target materials

    International Nuclear Information System (INIS)

    Court, G.R.; Niinikoski, T.O.; Cox, S.F.J.; Cragg, D.A.

    1980-10-01

    The proceedings are reported of a second international workshop which was convened to consider the use of polarised targets in nuclear research and in particular the experimental difficulties imposed by the limitations of target materials with respect to their relatively low hydrogen content and susceptibility to radiation damage. Papers presented were entitled: (1) Introduction and general review. (2) Theory of dynamic nuclear polarisation. (3) Radiation induced paramagnetic centres in organic and inorganic materials. (4) Dynamic nuclear polarisation with radiation induced free radicals. (5) Radiation damage of chemically doped materials. (6) Chemical doping. (7) Techniques and instrumentation. (8) The use of polarised nuclei in physics with neutrons. (9) The use of polarised targets in high energy physics. (U.K.)

  13. Proceedings of the Korean Society Nuclear Medicine Autumn Meeting 1998

    International Nuclear Information System (INIS)

    1998-01-01

    This proceedings contains articles of 1998 Autumn meeting of the Korean Society Nuclear Medicine. It was held on November 13-14, 1998 in Seoul, Korea. This proceedings is comprised of 5 sessions. The subject titles of session are as follows: general nuclear medicine, neurology, radiopharmacy and biology, nuclear cardiology, physics and instrumentation. (Yi, J. H.)

  14. Proceedings of the Korean Society Nuclear Medicine Autumn Meeting 1997

    International Nuclear Information System (INIS)

    1997-01-01

    This proceedings contains articles of 1997 autumn meeting of the Korean Society Nuclear Medicine. It was held on November 21, 1997 in Kwangju, Korea. This proceedings is comprised of 5 sessions. The subject titles of session are as follows: general nuclear medicine, neurology, radiopharmacy and biology, nuclear cardiology, physics and instrumentation. (Yi, J. H.)

  15. Proceeding of the Eighth Scientific Presentation on Nuclear Safety Technology

    International Nuclear Information System (INIS)

    Geni Rina Sunaryo; Sony Tjahjani, D.T.; Anhar Riza Antariksawan; Sudarno; Djoko Hari Nugroho; Roziq Himawan; Ari Satmoko; Histori; Sumijanto

    2003-02-01

    The Proceeding of Scientific Meeting and Presentation is routine activity that held in National Nuclear Energy Agency (BATAN) by Centre for Development of Nuclear Safety Technology for monitoring the research activity which was achieved in BATAN. The aims of the proceeding to able to information and reference for nuclear safety technology. There are 30 papers which separated index. (PPIN)

  16. Proceeding of the Fifth Scientific Presentation on Nuclear Safety Technology

    International Nuclear Information System (INIS)

    Suhaemi, Tj.; Sudarno; Sunaryo, G. R.; Supriatna, P.; Antariksawan, A. R.; Sumijanto; Febrianto; Histori; Aliq

    2000-01-01

    The proceedings includes the result of research and development activities on nuclear safety technology that have been done by research Center for Nuclear Safety Technology in 2000 and was presented on June 28, 2000. The proceedings is expected to give illustration of the research result on Nuclear Safety Technology

  17. Proceedings of the Korean Society Nuclear Medicine Autumn Meeting 2002

    International Nuclear Information System (INIS)

    2002-01-01

    This proceedings contains articles of 2002 autumn meeting of the Korean Society Nuclear Medicine. It was held on November 15-16, 2002 in Seoul, Korea. This proceedings is comprised of 5 sessions. The subject titles of session are as follows: Cancer, Physics of nuclear medicine, Neurology, Radiopharmacy and biology, General nuclear medicine. (Yi, J. H.)

  18. Thermodynamics of nuclear materials

    International Nuclear Information System (INIS)

    1979-01-01

    Full text: The science of chemical thermodynamics has substantially contributed to the understanding of the many problems encountered in nuclear and reactor technology. These problems include reaction of materials with their surroundings and chemical and physical changes of fuels. Modern reactor technology, by its very nature, has offered new fields of investigations for the scientists and engineers concerned with the design of nuclear fuel elements. Moreover, thermodynamics has been vital in predicting the behaviour of new materials for fission as well as fusion reactors. In this regard, the Symposium was organized to provide a mechanism for review and discussion of recent thermodynamic investigations of nuclear materials. The Symposium was held in the Juelich Nuclear Research Centre, at the invitation of the Government of the Federal Republic of Germany. The International Atomic Energy Agency has given much attention to the thermodynamics of nuclear materials, as is evidenced by its sponsorship of four international symposia in 1962, 1965, 1967, and 1974. The first three meetings were primarily concerned with the fundamental thermodynamics of nuclear materials; as with the 1974 meeting, this last Symposium was primarily aimed at the thermodynamic behaviour of nuclear materials in actual practice, i.e., applied thermodynamics. Many advances have been made since the 1974 meeting, both in fundamental and applied thermodynamics of nuclear materials, and this meeting provided opportunities for an exchange of new information on this topic. The Symposium dealt in part with the thermodynamic analysis of nuclear materials under conditions of high temperatures and a severe radiation environment. Several sessions were devoted to the thermodynamic studies of nuclear fuels and fission and fusion reactor materials under adverse conditions. These papers and ensuing discussions provided a better understanding of the chemical behaviour of fuels and materials under these

  19. Nuclear materials management procedures

    International Nuclear Information System (INIS)

    Veevers, K.; Silver, J.M.; Quealy, K.J.; Steege, E. van der.

    1987-10-01

    This manual describes the procedures for the management of nuclear materials and associated materials at the Lucas Heights Research Laboratories. The procedures are designed to comply with Australia's nuclear non-proliferation obligations to the International Atomic Energy Agency (IAEA), bilateral agreements with other countries and ANSTO's responsibilities under the Nuclear Non-Proliferation (Safeguards) Act, 1987. The manual replaces those issued by the Australian Atomic Energy Commission in 1959, 1960 and 1969

  20. The nuclear materials contraband

    International Nuclear Information System (INIS)

    Williams, P.; Woessner, P.

    1996-01-01

    Several seizures of nuclear materials carried by contraband have been achieved. Some countries or criminal organizations could manufacture atomic bombs and use them. This alarming situation is described into details. Only 40% of drugs are seized by the American police and probably less in western Europe. The nuclear materials market is smaller than the drugs'one but the customs has also less experience to intercept the uranium dispatch for instance more especially as the peddlers are well organized. A severe control of the international transports would certainly allow to seize a large part of nuclear contraband materials but some dangerous isotopes as uranium 235 or plutonium 239 are little radioactive and which prevents their detection by the Geiger-Mueller counters. In France, some regulations allow to control the materials used to manufacture the nuclear weapons, and diminish thus the risk of a nuclear materials contraband. (O.L.). 4 refs., 2 figs

  1. Nuclear physics methods in materials research

    International Nuclear Information System (INIS)

    Bethge, K.; Baumann, H.; Jex, H.; Rauch, F.

    1980-01-01

    Proceedings of the seventh divisional conference of the Nuclear Physics Division held at Darmstadt, Germany, from 23rd through 26th of September, 1980. The scope of this conference was defined as follows: i) to inform solid state physicists and materials scientists about the application of nuclear physics methods; ii) to show to nuclear physicists open questions and problems in solid state physics and materials science to which their methods can be applied. According to the intentions of the conference, the various nuclear physics methods utilized in solid state physics and materials science and especially new developments were reviewed by invited speakers. Detailed aspects of the methods and typical examples extending over a wide range of applications were presented as contributions in poster sessions. The Proceedings contain all the invited papers and about 90% of the contributed papers. (orig./RW)

  2. Auditing nuclear materials statements

    International Nuclear Information System (INIS)

    Anon.

    1973-01-01

    A standard that may be used as a guide for persons making independent examinations of nuclear materials statements or reports regarding inventory quantities on hand, receipts, production, shipment, losses, etc. is presented. The objective of the examination of nuclear materials statements by the independent auditor is the expression of an opinion on the fairness with which the statements present the nuclear materials position of a nuclear materials facility and the movement of such inventory materials for the period under review. The opinion is based upon an examination made in accordance with auditing criteria, including an evaluation of internal control, a test of recorded transactions, and a review of measured discards and materials unaccounted for (MUF). The standard draws heavily upon financial auditing standards and procedures published by the American Institute of Certified Public Accountants

  3. Proceeding of the Fifth Scientific Presentation on Nuclear Fuel Cycle: Development of Nuclear Fuel Cycle Technology in Third Millennium

    International Nuclear Information System (INIS)

    Suripto, A.; Sastratenaya, A.S.; Sutarno, D.

    2000-01-01

    The proceeding contains papers presented in the Fifth Scientific Presentation on Nuclear Fuel Element Cycle with theme of Development of Nuclear Fuel Cycle Technology in Third Millennium, held on 22 February in Jakarta, Indonesia. These papers were divided by three groups that are technology of exploration, processing, purification and analysis of nuclear materials; technology of nuclear fuel elements and structures; and technology of waste management, safety and management of nuclear fuel cycle. There are 35 papers indexed individually. (id)

  4. Nuclear physics, neutron physics and nuclear energy. Proceedings

    International Nuclear Information System (INIS)

    Andrejtscheff, W.; Elenkov, D.

    1994-01-01

    The book contains of proceedings of XI International School on Nuclear Physics, Neutron Physics and Nuclear Energy organized traditionally every two years by Bulgarian Academy of Sciences and the Physics Department of Sofia University held near the city of Varna. It provides a good insight to the large range of theoretical and experimental results, prospects, problems, difficulties and challenges which are at the core of nuclear physics today. The efforts and achievements of scientists to search for new phenomena in nuclei at extreme circumstances as superdeformation and band crossing in nuclear structure understanding are widely covered. From this point of view the achievements and future in the field of high-precision γ-spectroscopy are included. Nuclear structure models and methods, models for strong interaction, particle production and properties, resonance theory and its application in reactor physics are comprised also. (V.T.)

  5. Proceedings of the conference on nuclear structure at the limits

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    This report contains the papers from the Proceedings of the Conference on Nuclear Structure at the Limits. Some of the areas covered by these papers are: nuclear deformation; nuclear decay; nuclear spectroscopy; radioactive ion beams; nuclear models; high spin states; and heavy ion reactions. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

  6. Proceedings of the conference on nuclear structure at the limits

    International Nuclear Information System (INIS)

    1996-01-01

    This report contains the papers from the Proceedings of the Conference on Nuclear Structure at the Limits. Some of the areas covered by these papers are: nuclear deformation; nuclear decay; nuclear spectroscopy; radioactive ion beams; nuclear models; high spin states; and heavy ion reactions. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database

  7. Nuclear material operations manual

    International Nuclear Information System (INIS)

    Tyler, R.P.

    1981-02-01

    This manual provides a concise and comprehensive documentation of the operating procedures currently practiced at Sandia National Laboratories with regard to the management, control, and accountability of nuclear materials. The manual is divided into chapters which are devoted to the separate functions performed in nuclear material operations-management, control, accountability, and safeguards, and the final two chapters comprise a document which is also issued separately to provide a summary of the information and operating procedures relevant to custodians and users of radioactive and nuclear materials. The manual also contains samples of the forms utilized in carrying out nuclear material activities. To enhance the clarity of presentation, operating procedures are presented in the form of playscripts in which the responsible organizations and necessary actions are clearly delineated in a chronological fashion from the initiation of a transaction to its completion

  8. Nuclear material operations manuals

    International Nuclear Information System (INIS)

    Tyler, R.P.

    1979-06-01

    This manual is intended to provide a concise and comprehensive documentation of the operating procedures currently practiced at Sandia Laboratories with regard to the management, control, and accountability of radioactive and nuclear materials. The manual is divided into chapters which are devoted to the separate functions performed in nuclear material operations-management, control, accountability, and safeguards, and the final two chapters comprise a document which is also issued separately to provide a summary of the information and operating procedures relevant to custodians and users of radioactive and nuclear materials. The manual also contains samples of the forms utilized in carrying out nuclear material activities. To enhance the clarity of presentation, operating procedures are presented in the form of playscripts in which the responsible organizations and necessary actions are clearly delineated in a chronological fashion from the initiation of a transaction to its completion

  9. Nuclear material operations manual

    International Nuclear Information System (INIS)

    Tyler, R.P.; Gassman, L.D.

    1978-04-01

    This manual is intended to provide a concise and comprehensive documentation of the operating procedures currently practiced at Sandia Laboratories with regard to the management, control, and accountability of radioactive and nuclear materials. The manual is divided into chapters which are devoted to the separate functions performed in nuclear material operations--management, control, accountability, and safeguards, and the final two chapters comprise a document which is also issued separately to provide a summary of the information and operating procedures relevant to custodians and users of radioactive and nuclear materials. The manual also contains samples of the forms utilized in carrying out nuclear material activities. To enhance the clarity of presentation, operating procedures are presented in the form of ''play-scripts'' in which the responsible organizations and necessary actions are clearly delineated in a chronological fashion from the initiation of a transaction to its completion

  10. Smuggling special nuclear materials

    International Nuclear Information System (INIS)

    Lazaroiu, Gheorghe

    1999-01-01

    Ever since the collapse of the former Soviet Union reports have circulated with increasing frequency concerning attempts to smuggle materials from that country's civil and military nuclear programs. Such an increase obviously raises a number of concerns (outlined in the author's introduction), chief among which is the possibility that these materials might eventually fall into the hands of proliferant states or terrorist groups. The following issues are presented: significance of materials being smuggled; sources and smuggling routes; potential customers; international efforts to reduce nuclear smuggling; long-term disposition of fissile materials. (author)

  11. Proceedings of the Korean Society Nuclear Medicine Spring Meeting 2002

    International Nuclear Information System (INIS)

    2002-01-01

    This proceedings contains articles of 2002 Spring meeting of the Korean Society Nuclear Medicine. It was held on May 17, 2002 in Suwon, Korea. This proceedings is comprised of 3 sessions. The subject titles of session are as follows: Gynecological and Colorectal cancer, Lung cancer and Lymphoma, and general nuclear medicine. (Yi, J. H.)

  12. The Proceeding on National Seminar in Nuclear Science and Technology

    International Nuclear Information System (INIS)

    Duyeh Setiawan; Rochestri Sofyan; Nurlaila Z; Poppy Intan Tjahaja; Efrizon Umar; Muhayatun; Nanny K Oekar; Sudjatmi K Alfa; Dani Gustaman Syarif; Didi Gayani; Djoko Hadi P; Saeful Hidayat; Ari Darmawan Pasek; Nathanel P Tandian; Toto Hardianto

    2009-11-01

    The proceeding on national seminar in nuclear science and technology by National Atomic energy Agency held in Bandung on June 3, 2009. The topic of the seminar is the increasing the role of nuclear science and technology for the welfare. The proceeding consist of the article from BATAN participant as well as outside. (PPIN)

  13. Automated nuclear materials accounting

    International Nuclear Information System (INIS)

    Pacak, P.; Moravec, J.

    1982-01-01

    An automated state system of accounting for nuclear materials data was established in Czechoslovakia in 1979. A file was compiled of 12 programs in the PL/1 language. The file is divided into four groups according to logical associations, namely programs for data input and checking, programs for handling the basic data file, programs for report outputs in the form of worksheets and magnetic tape records, and programs for book inventory listing, document inventory handling and materials balance listing. A similar automated system of nuclear fuel inventory for a light water reactor was introduced for internal purposes in the Institute of Nuclear Research (UJV). (H.S.)

  14. Thermodynamics of nuclear materials

    International Nuclear Information System (INIS)

    Rand, M.H.

    1975-01-01

    A report is presented of the Fourth International Symposium on Thermodynamics of Nuclear Materials held in Vienna, 21-25 October 1974. The technological theme of the Symposium was the application of thermodynamics to the understanding of the chemistry of irradiated nuclear fuels and to safety assessments for hypothetical accident conditions in reactors. The first four sessions were devoted to these topics and they were followed by four more sessions on the more basic thermodynamics, phase diagrams and the thermodynamic properties of a wide range of nuclear materials. Sixty-seven papers were presented

  15. Professional Nuclear Materials Management

    International Nuclear Information System (INIS)

    Forcella, A.A.; O'Leary, W.J.

    1966-01-01

    This paper describes the scope of nuclear materials management for a typical power reactor in the United States of America. Since this power reactor is financed by private capital, one of the principal obligations of the reactor operator is to ensure that the investment is protected and will furnish an adequate financial return. Because of the high intrinsic value of nuclear materials, appropriate security and accountability must be continually exercised to minimize losses beyond security and accountability for the nuclear materials. Intelligent forethought and planning must be employed to ensure that additional capital is not lost as avoidable additional costs or loss of revenue in a number of areas. The nuclear materials manager must therefore provide in advance against the following contingencies and maintain constant control or liaison against deviations from planning during (a) pre-reactor acquisition of fuel and fuel elements, (b) in-reactor utilization of the fuel elements, and (c) post-reactor recovery of fuel values. During pre-reactor planning and operations, it is important that the fuel element be designed for economy in manufacture, handling, shipping, and replaceability. The time schedule for manufacturing operations must minimize losses of revenue from unproductive dead storage of high cost materials. For in-reactor operations, the maximum achievable burn-up of the fissionable material must be obtained by means of appropriate fuel rearrangement schemes. Concurrently the unproductive down-time of the reactor for fuel rearrangement, inspections, and the like must be minimized. In the post-reactor period, when the fuel has reached a predetermined depletion of fissionable material, the nuclear materials manager must provide for the most economical reprocessing and recovery of fissionable values and by-products. Nuclear materials management is consequently an essential factor in achieving competitive fuel cycle and unit energy costs with power reactors

  16. Detecting Illicit Nuclear Materials

    International Nuclear Information System (INIS)

    Kouzes, Richard T.

    2005-01-01

    The threat that weapons of mass destruction might enter the United States has led to a number of efforts for the detection and interdiction of nuclear, radiological, chemical, and biological weapons at our borders. There have been multiple deployments of instrumentation to detect radiation signatures to interdict radiological material, including weapons and weapons material worldwide

  17. Proceedings of the Tripartite Seminar on Nuclear Material Accounting and Control at Radiochemical Plants; Trudy trekhstoronnego seminara Uchet i kontrol' yadernykh materialov na radiokhimicheskikh ustanovkakh

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    The problems of creation and operation of nuclear materials (NM) control and accounting systems and their components at radiochemical plants were discussed in seminar during November 2-6 of 1998. There were 63 Russian and 25 foreign participants in seminar. The seminar programme includes following sessions and articles: the aspects of State NM control and accountancy; NM control and accounting in radiochemical plants and at separate stages of reprocessing of spent nuclear fuel and irradiated fuel elements of commercial reactors; NM control and accountancy in storage facilities of radiochemical plants; NM control and accounting computerization, material balance assessment, preparation of reports; qualitative and quantitative measurements in NM control and accounting at radiochemical plants destructive analysis techniques.

  18. Proceedings of 8. national conference on nuclear electronic and nuclear detection technology: Pt.1

    International Nuclear Information System (INIS)

    1996-01-01

    The 8th National Conference on Nuclear Electronics and Nuclear Detection Technology was held during 2-7, 12, 1996 in Zhuhai, Guangdong, China. 184 pieces of papers were collected in the conference proceedings. The contents of the conference proceedings are: nuclear electronics, nuclear detectors, nuclear instruments and its application, nuclear medical electronics, computer applications in nuclear sciences and technology, measurement of nuclear monitoring and nuclear explosion, radiation hardened electronics, liquid scintillation counting techniques and miscellaneous. Reported hereafter is the first part of the proceedings

  19. Proceedings of NUCLEAR 2008 annual international conference on sustainable development through nuclear research and education

    International Nuclear Information System (INIS)

    Constantin, Marin; Turcu, Ilie

    2008-01-01

    The proceedings of the NUCLEAR 2008 annual international conference on sustainable development through nuclear research and education held at INR-Pitesti on May, 28 - 30 2008 contain 88 communications presented in 3 sections addressing the themes of Nuclear energy, Environmental protection, and Sustainable development. In turn these sections are addressing the following items: Section 1.1 - Nuclear safety and severe accidents (12 papers); Section 1.2 - Nuclear reactors (11 papers); Section 1.3 - Nuclear technologies and materials (20 papers); Section 2.1 - Radioprotection (5 papers); Section 2.2 - Radioactive waste management (20 papers); Section 2.3 - air, water and soil protection (5 papers); Section 3.1 - Strategies in energy (3 papers); Section 3.2 - Education, continuous formation and knowledge transfer (8 papers); Section 3.3 - International partnership for a sustainable development (4 papers)

  20. Safeguards on nuclear materials

    International Nuclear Information System (INIS)

    Cisar, V.; Keselica, M.; Bezak, S.

    2001-01-01

    The article describes the implementation of IAEA safeguards for nuclear materials in the Czech and Slovak Republics, the establishment and development of the State System of Accounting for and Control of Nuclear Material (SSAC) at the levels of the state regulatory body and of the operator, particularly at the Dukovany nuclear power plant. A brief overview of the historical development is given. Attention is concentrated on the basic concepts and legal regulation accepted by the Czech and Slovak Republics in accordance with the new approach to create a complete legislative package in the area of nuclear energy uses. The basic intention is to demonstrate the functions of the entire system, including safeguards information processing and technical support of the system. Perspectives of the Integrated Safeguards System are highlighted. The possible ways for approximation of the two national systems to the Safeguards System within the EU (EURATOM) are outlined, and the necessary regulatory and operators' roles in this process are described. (author)

  1. Advanced research workshop: nuclear materials safety

    International Nuclear Information System (INIS)

    Jardine, L J; Moshkov, M M.

    1999-01-01

    The Advanced Research Workshop (ARW) on Nuclear Materials Safety held June 8-10, 1998, in St. Petersburg, Russia, was attended by 27 Russian experts from 14 different Russian organizations, seven European experts from six different organizations, and 14 U.S. experts from seven different organizations. The ARW was conducted at the State Education Center (SEC), a former Minatom nuclear training center in St. Petersburg. Thirty-three technical presentations were made using simultaneous translations. These presentations are reprinted in this volume as a formal ARW Proceedings in the NATO Science Series. The representative technical papers contained here cover nuclear material safety topics on the storage and disposition of excess plutonium and high enriched uranium (HEU) fissile materials, including vitrification, mixed oxide (MOX) fuel fabrication, plutonium ceramics, reprocessing, geologic disposal, transportation, and Russian regulatory processes. This ARW completed discussions by experts of the nuclear materials safety topics that were not covered in the previous, companion ARW on Nuclear Materials Safety held in Amarillo, Texas, in March 1997. These two workshops, when viewed together as a set, have addressed most nuclear material aspects of the storage and disposition operations required for excess HEU and plutonium. As a result, specific experts in nuclear materials safety have been identified, know each other from their participation in t he two ARW interactions, and have developed a partial consensus and dialogue on the most urgent nuclear materials safety topics to be addressed in a formal bilateral program on t he subject. A strong basis now exists for maintaining and developing a continuing dialogue between Russian, European, and U.S. experts in nuclear materials safety that will improve the safety of future nuclear materials operations in all the countries involved because of t he positive synergistic effects of focusing these diverse backgrounds of

  2. Nuclear material accounting handbook

    International Nuclear Information System (INIS)

    2008-01-01

    The handbook documents existing best practices and methods used to account for nuclear material and to prepare the required nuclear material accounting reports for submission to the IAEA. It provides a description of the processes and steps necessary for the establishment, implementation and maintenance of nuclear material accounting and control at the material balance area, facility and State levels, and defines the relevant terms. This handbook serves the needs of State personnel at various levels, including State authorities, facility operators and participants in training programmes. It can assist in developing and maintaining accounting systems which will support a State's ability to account for its nuclear material such that the IAEA can verify State declarations, and at the same time support the State's ability to ensure its nuclear security. In addition, the handbook is useful for IAEA staff, who is closely involved with nuclear material accounting. The handbook includes the steps and procedures a State needs to set up and maintain to provide assurance that it can account for its nuclear material and submit the prescribed nuclear material accounting reports defined in Section 1 and described in Sections 3 and 4 in terms of the relevant agreement(s), thereby enabling the IAEA to discharge its verification function as defined in Section 1 and described in Sections 3 and 4. The contents of the handbook are based on the model safeguards agreement and, where applicable, there will also be reference to the model additional protocol. As a State using The handbook consists of five sections. In Section 1, definitions or descriptions of terms used are provided in relation to where the IAEA applies safeguards or, for that matter, accounting for and control of nuclear material in a State. The IAEA's approach in applying safeguards in a State is also defined and briefly described, with special emphasis on verification. In Section 2, the obligations of the State

  3. Structural materials for innovative nuclear systems (SMINS)

    International Nuclear Information System (INIS)

    2008-01-01

    Structural materials research is a field of growing relevance in the nuclear sector, especially for the different innovative reactor systems being developed within the Generation IV International Forum (GIF), for critical and subcritical transmutation systems, and of interest to the Global Nuclear Energy Partnership (GNEP). Under the auspices of the NEA Nuclear Science Committee (NSC) the Workshop on Structural Materials for Innovative Nuclear Systems (SMINS) was organised in collaboration with the Forschungszentrum Karlsruhe in Germany. The objectives of the workshop were to exchange information on structural materials research issues and to discuss ongoing programmes, both experimental and in the field of advanced modelling. These proceedings include the papers and the poster session materials presented at the workshop, representing the international state of the art in this domain. (author)

  4. Proceedings of the Scientific Meeting and Presentation on Basic Research in Nuclear of the Science and Technology part I : Physics and Nuclear Reactor

    International Nuclear Information System (INIS)

    Kusminarto; Sri Juari Santoso; Agus Taftazani; Sudjatmoko; Darsono; Samin; Syarip; Prajitno; Muhadi Ayub Wasitho; Sukarsono; Tjipto Sujitno; Elisabeth Supriyatni

    2009-07-01

    The Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is a routine activity held by Centre for Accelerator Technology and Material Process, National Nuclear Energy Agency, for monitoring the research activity which achieved in National Nuclear Energy Agency. The proceedings contains papers presented on scientific meeting about Physics and Nuclear Reactor. The proceedings is the first part of the three parts which published in series. There are 28 papers. (PPIN)

  5. Nuclear materials transportation

    International Nuclear Information System (INIS)

    Ushakov, B.A.

    1986-01-01

    Various methods of nuclear materials transportation at different stages of the fuel cycle (U 3 O 8 , UF 6 production enrichment, fuel element manufacturing, storage) are considered. The advantages and drawbacks of railway, automobile, maritime and air transport are analyzed. Some types of containers are characterized

  6. Proceedings of NUCLEAR 2009 international conference on sustainable development through nuclear research and education

    International Nuclear Information System (INIS)

    Constantin, Marin; Turcu, Ilie

    2009-01-01

    The proceedings of the NUCLEAR 2009 international conference on sustainable development through nuclear research and education held at INR-Pitesti on May, 27 - 29 2009 contain 92 communications presented in two plenary sessions (6 and 4 talks, respectively) and three sections addressing the themes of Nuclear energy, Environmental protection, and Sustainable development. In turn these sections are addressing the following items: Section 1.1 - Nuclear safety and severe accidents (8 papers); Section 1.2 - Nuclear reactors (15 papers); Section 1.3 - Nuclear technologies and materials (32 papers); Section 2.1 - Radioactive waste management (18 papers; Section 2.2 and Section 2.3 - Radioprotection and air, water and soil protection (12 papers); Section 3.1 - Education, continuous formation and knowledge transfer (9 papers); Section 3.2 -Strategies in energy (Round table) (5 papers). A number of 17 papers although programmed have not actually been presented within these proceedings. These papers are presented as abstracts in 'Nuclear 2009 - BOOK of ABSTRACTS', separately processed

  7. Proceedings of DAE-BRNS third international symposium on materials chemistry

    International Nuclear Information System (INIS)

    Tyagi, Deepak; Banerjee, Atindra Mohan; Nigam, Sandeep; Varma, Salil; Tripathi, Arvind Kumar; Bharadwaj, Shyamala Rajkumar; Das, Dasarathi

    2010-12-01

    The present volume consists of the proceedings of the DAE-BRNS Third International Symposium on Materials Chemistry. In order to keep pace with the advancements made in the area of materials chemistry, new topics like materials for energy conversion, biomaterials, carbon based materials, soft condensed materials, thin films, surface chemistry, polymer based materials, organic and organometallics, magnetic materials and high purity materials have been included in this symposium while topics like nuclear materials, nanomaterials and clusters, catalysis, chemical sensors, fuel cell materials and computational research in materials chemistry have been continued as important features of the symposium. Papers relevant to INIS are indexed separately

  8. Nuclear materials transport worldwide

    International Nuclear Information System (INIS)

    Stellpflug, J.

    1987-01-01

    This Greenpeace report shows: nuclear materials transport is an extremely hazardous business. There is no safe protection against accidents, kidnapping, or sabotage. Any moment of a day, at any place, a nuclear transport accident may bring the world to disaster, releasing plutonium or radioactive fission products to the environment. Such an event is not less probable than the MCA at Chernobyl. The author of the book in hand follows the secret track of radioactive materials around the world, from uranium mines to the nuclear power plants, from reprocessing facilities to the waste repositories. He explores the routes of transport and the risks involved, he gives the names of transport firms and discloses incidents and carelessness, tells about damaged waste drums and plutonium that 'disappeared'. He also tells about worldwide, organised resistance to such nuclear transports, explaining the Greenpeace missions on the open sea, or the 'day X' operation at the Gorleben site, informing the reader about protests and actions for a world freed from the threat of nuclear energy. (orig./HP) [de

  9. Proceedings of the Canadian Nuclear Society sixth annual conference

    International Nuclear Information System (INIS)

    French, P.M.; Phillips, G.J.

    1985-01-01

    The proceedings of the Sixth Annual Conference of the Canadian Nuclear Society comprise 103 papers on the following subjects: fuel technology, nuclear plant safety, instrumentation, public and regulatory matters, fusion, fuel behaviour under normal and accident conditions, nuclear plant design and operations, thermal hydraulics, reactor physics, accelerators, waste management, new reactor concepts

  10. Proceedings of the 4. Brazilian meeting on nuclear applications

    International Nuclear Information System (INIS)

    1997-01-01

    In this proceedings, theoretical and experimental papers were presented covering the following areas: radiation monitoring and dosimetry, nuclear medicine, radiochemistry, environmental sciences, nuclear instrumentation, waste management, industry and mining, medicine and health, agriculture, biology, radioisotopes, hydrology and sediments, irradiators and nuclear reactors

  11. Proceedings of the Canadian Nuclear Association 35. annual conference

    International Nuclear Information System (INIS)

    Loewer, R.

    1995-01-01

    The proceedings of the thirty-fifth annual conference of the Canadian Nuclear Association contain 22 papers organized in the following sessions: update on the status of the Canadian nuclear industry, non-proliferation and related political issues, nuclear waste disposal perspectives, regulatory issues, trade development, new markets, economics of nuclear electricity, public acceptance or rejection. In addition one paper from a CNA/CNS special session on nuclear diffraction is included. The individual papers have been abstracted separately

  12. Proceedings of the third nuclear thermal hydraulics meeting

    International Nuclear Information System (INIS)

    Anon.

    1987-01-01

    This book contains the proceedings of the Thermal Hydraulics Division of the American Nuclear Society. The papers presented include: Simulator qualification using engineering codes and Development of thermal hydraulic analysis capabilities for Oyster Creek

  13. International nuclear material safeguards

    International Nuclear Information System (INIS)

    Syed Azmi Syed Ali

    1985-01-01

    History can be a very dull subject if it relates to events which have long since lost their relevance. The factors which led to the creation of the International Atomic Energy Agency (IAEA), however, are as important and relevant today as they were when the Agency was first created. Without understanding these factors it is impossible to realise how important the Agency is in the present world or to understand some of the controversies surrounding its future. Central to these controversies is the question of how best to promote the international transfer of nuclear technology without contributing further to the problem of proliferating nuclear explosives or explosive capabilities. One effective means is to subject nuclear materials (see accompanying article in box), which forms the basic link between the manufacture of nuclear explosives and nuclear power generation, to international safeguards. This was realized very early in the development of nuclear power and was given greater emphasis following the deployment of the first two atomic bombs towards the end of World War II. (author)

  14. Proceedings of the 11th Annual Conference of the Canadian Nuclear Society

    International Nuclear Information System (INIS)

    Rouben, B.

    1990-01-01

    This volume contains the proceedings of the thirteen technical sessions at the 11. annual conference of the Canadian Nuclear Society. The 68 papers presented at this conference cover the areas of programmes and issues for the 90's; thermalhydraulics; reactor physics and fuel management; nuclear safety; small reactors; fuel behaviour; energy production and the environment; computer applications; nuclear systems; fusion; reactor decommissioning, irradiated fuel and materials handling; and reactor components, (L.L.)

  15. Proceedings of the International Conference Nuclear Energy in Central Europe 2001

    International Nuclear Information System (INIS)

    Jencic, I.; Glumac, B.

    2001-01-01

    International Conference Nuclear Energy in Central Europe is an annual meeting of the Nuclear Society of Slovenia. The proceedings contain 98 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region. Topics are: reactor physics, thermal hydraulics, probabilistic safety assessment (PSA) and severe accidents, nuclear materials, NPP and research reactor operation, environmental issues and radiation measurement, fusion, radioactive waste and regulatory issues and public relations

  16. Materials for nuclear reactors

    International Nuclear Information System (INIS)

    Banerjee, S.; Kamath, H.S.

    2005-01-01

    The improved performance of present generation nuclear reactors and the realization of advanced reactor concepts, both, require development of better materials. Physical metallurgy/materials science principles which have been exploited in meeting the exacting requirements of nuclear reactor materials (fuels and structural materials), are outlined citing a few specific examples. While the incentive for improvement of traditional fuels (e.g., UO 2 fuel) is primarily for increasing the average core burn up, the development of advanced fuels (e.g., MOX, mixed carbide, nitride, silicide and dispersion fuels) are directed towards better utilization of fissile and fertile inventories through adaptation of innovative fuel cycles. As the burn up of UO 2 fuel reaches higher levels, a more detailed and quantitative understanding of the phenomena such as fission gas release, fuel restructuring induced by radiation and thermal gradients and pellet-clad interaction is being achieved. Development of zirconium based alloys for both cladding and pressure tube applications is discussed with reference to their physical metallurgy, fabrication techniques and in-reactor degradation mechanisms. The issue of radiation embrittlement of reactor pressure vessels (RPVs) is covered drawing a comparison between the western and eastern specifications of RPV steels. The search for new materials which can stand higher rates of atomic displacement due to radiation has led to the development of swelling resistant austenitic and ferritic stainless steels for fast reactor applications as exemplified by the development of the D-9 steel for Indian fast breeder reactor. The presentation will conclude by listing various materials related phenomena, which have a strong bearing on the successful development of future nuclear energy systems. (author)

  17. Uranium Raw Material for the Nuclear Fuel Cycle: Exploration, Mining, Production, Supply and Demand, Economics and Environmental Issues (URAM-2009). Proceedings of an International Symposium

    International Nuclear Information System (INIS)

    2014-05-01

    This IAEA symposium is a third in a series which began in 2000 to discuss issues related to uranium raw materials. The symposia covered all areas of the uranium production cycle — including uranium geology, exploration, mining; milling and refining of uranium concentrates; and safety, environmental, social, training and regulatory issues — and reported on uranium supply and demand, and market scenarios. The first symposium was held in October 2000 — a time of extremely depressed market prices for uranium and of mines being closed — and primarily addressed environmental and safety issues in the uranium production cycle. By the time the second symposium was held in June 2005, the uranium market had started to improve after nearly two decades of depressed activity because of increased demand due to rising expectations for nuclear power expansion. Since then, there has been a dramatic rise in the uranium spot price, which in turn has promoted a significant increase in uranium exploration activities all over the world. The international symposium on Uranium Raw Material for the Nuclear Fuel Cycle (URAM-2009) was held at the IAEA, Vienna, 22–26 June 2009, at a time when nuclear energy was emerging as a viable alternative to meet the ever increasing demand of electricity in a sustainable manner, without degrading the environment. However, the global recession and credit crunch could impact the growth of the uranium industry. Since 2000, the identified uranium resource base has grown by more than 75%, exploration efforts have continued to increase in greenfield as well as brownfield sites, annual uranium production has risen, and the issue of social licensing and uranium stewardship has become increasingly important for public acceptance of the uranium industry. Some 210 delegates from 33 States and four international organizations participated in the symposium. In total, 120 technical papers were presented in the oral and poster sessions, and an exhibition on

  18. Uranium Raw Material for the Nuclear Fuel Cycle: Exploration, Mining, Production, Supply and Demand, Economics and Environmental Issues (URAM-2009). Proceedings of an International Symposium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-05-15

    This IAEA symposium is a third in a series which began in 2000 to discuss issues related to uranium raw materials. The symposia covered all areas of the uranium production cycle — including uranium geology, exploration, mining; milling and refining of uranium concentrates; and safety, environmental, social, training and regulatory issues — and reported on uranium supply and demand, and market scenarios. The first symposium was held in October 2000 — a time of extremely depressed market prices for uranium and of mines being closed — and primarily addressed environmental and safety issues in the uranium production cycle. By the time the second symposium was held in June 2005, the uranium market had started to improve after nearly two decades of depressed activity because of increased demand due to rising expectations for nuclear power expansion. Since then, there has been a dramatic rise in the uranium spot price, which in turn has promoted a significant increase in uranium exploration activities all over the world. The international symposium on Uranium Raw Material for the Nuclear Fuel Cycle (URAM-2009) was held at the IAEA, Vienna, 22–26 June 2009, at a time when nuclear energy was emerging as a viable alternative to meet the ever increasing demand of electricity in a sustainable manner, without degrading the environment. However, the global recession and credit crunch could impact the growth of the uranium industry. Since 2000, the identified uranium resource base has grown by more than 75%, exploration efforts have continued to increase in greenfield as well as brownfield sites, annual uranium production has risen, and the issue of social licensing and uranium stewardship has become increasingly important for public acceptance of the uranium industry. Some 210 delegates from 33 States and four international organizations participated in the symposium. In total, 120 technical papers were presented in the oral and poster sessions, and an exhibition on

  19. Uranium Raw Material for the Nuclear Fuel Cycle: Exploration, Mining, Production, Supply and Demand, Economics and Environmental Issues (URAM-2009). Proceedings of an International Symposium

    International Nuclear Information System (INIS)

    2014-06-01

    This IAEA symposium is a third in a series which began in 2000 to discuss issues related to uranium raw materials. The symposia covered all areas of the uranium production cycle — including uranium geology, exploration, mining; milling and refining of uranium concentrates; and safety, environmental, social, training and regulatory issues — and reported on uranium supply and demand, and market scenarios. The first symposium was held in October 2000 — a time of extremely depressed market prices for uranium and of mines being closed — and primarily addressed environmental and safety issues in the uranium production cycle. By the time the second symposium was held in June 2005, the uranium market had started to improve after nearly two decades of depressed activity because of increased demand due to rising expectations for nuclear power expansion. Since then, there has been a dramatic rise in the uranium spot price, which in turn has promoted a significant increase in uranium exploration activities all over the world. The international symposium on Uranium Raw Material for the Nuclear Fuel Cycle (URAM-2009) was held at the IAEA, Vienna, 22–26 June 2009, at a time when nuclear energy was emerging as a viable alternative to meet the ever increasing demand of electricity in a sustainable manner, without degrading the environment. However, the global recession and credit crunch could impact the growth of the uranium industry. Since 2000, the identified uranium resource base has grown by more than 75%, exploration efforts have continued to increase in greenfield as well as brownfield sites, annual uranium production has risen, and the issue of social licensing and uranium stewardship has become increasingly important for public acceptance of the uranium industry. Some 210 delegates from 33 States and four international organizations participated in the symposium. In total, 120 technical papers were presented in the oral and poster sessions, and an exhibition on

  20. Thermodynamics of nuclear materials

    International Nuclear Information System (INIS)

    1962-01-01

    The first session of the symposium discussed in general the thermodynamic properties of actinides, including thorium, uranium and Plutonium which provide reactor fuel. The second session was devoted to applications of thermodynamic theory to the study of nuclear materials, while the experimental techniques for the determination of thermodynamic data were examined at the next session. The thermodynamic properties of alloys were considered at a separate session, and another session was concerned with solids other than alloys. Vaporization processes, which are of special interest in the development of high-temperature reactors, were discussed at a separate session. The discussions on the methods of developing the data and ascertaining their accuracy were especially useful in highlighting the importance of determining whether any given data are reliable before they can be put to practical application. Many alloys and refractory materials (i. e. materials which evaporate only at very high temperatures) are of great importance in nuclear technology, and some of these substances are extremely complex in their chemical composition. For example, until recently the phase composition of the oxides of thorium, uranium and plutonium had been only very imperfectly understood, and the same was true of the carbides of these elements. Recent developments in experimental techniques have made it possible to investigate the phase composition of these complex materials as well as the chemical species of these materials in the gaseous phase. Recent developments in measuring techniques, such as fluorine bomb calorimetry and Knudsen effusion technique, have greatly increased the accuracy of thermodynamic data

  1. Nuclear Electronics. Proceedings of a Conference on Nuclear Electronics

    International Nuclear Information System (INIS)

    1966-01-01

    The science of electronics, which is playing a decisive role in the modern world, is particularly important in the development of the nuclear sciences, both in fundamental research on the structure of matter and in the production of power from fission. It is impractical, however, to deal with this vast and varied subject at one time. The Agency's first conference on the subject, at Belgrade in May 1961, was restricted to just a few aspects of nuclear electronics. The second conference, organized by the Agency in co-operation with the Indian Atomic Energy Commission and held at Bombay from 22 to 26 November 1965, was limited, for all practical purposes, to the use of nuclear electronics in reactor control and safety. The importance of this subject is self-evident, for the number of power reactors throughout the world is increasing every year and the economics of their operation depends just as much on optimum functioning as on improved safety. The Bombay conference, at which 48 papers were presented, was attended by a large number of participants, representing 12 countries and two international organizations. The main topics were power and neutron-flux measurements, reactor control, safety devices, and data processing to ensure optimum operation. The Proceedings, which contain both the texts and discussions of the papers presented, are of immediate interest to specialists in these fields and should form a valuable source of information

  2. Proceedings of the 1998 symposium on nuclear data

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Tadashi; Fukahori, Tokio [eds.] [Japanese Nuclear Data Committee, Tokai, Ibaraki (Japan)

    1999-03-01

    The 1998 Symposium on Nuclear Data was held at Tokai Research Establishment, Japan Atomic Energy Research Institute (JAERI), on 19th and 20th of November 1998. Japanese Nuclear Data Committee and Nuclear Data Center, JAERI organized this symposium. In the oral sessions, presented papers were on accelerator facilities, astrophysics and nuclear data, international session, radiation damage study and nuclear data, and integral test of nuclear data. In the poster session, presented papers were concerning experiments, evaluations, benchmark tests and on-line database on nuclear data. Those presented papers are compiled in this proceedings. The 50 of the presented papers are indexed individually. (J.P.N.)

  3. Proceedings of the Canadian Nuclear Association 34. annual conference

    International Nuclear Information System (INIS)

    Girard, A.M.

    1994-01-01

    The proceedings of the thirty-fourth annual conference of the Canadian Nuclear Association contain 23 complete papers and three speeches organized in the following sessions: opening, plenary, new environmental regulations and their effect on the energy industry, CANDU update, life cycle management of nuclear power plants, evolution of nuclear technology, technologies for tomorrow, nuclear used fuel and disposal of low-level waste, world economics and energy consumption. The complete papers have been abstracted separately

  4. Proceedings of the Canadian Nuclear Association 34. annual conference

    Energy Technology Data Exchange (ETDEWEB)

    Girard, A M [Atomic Energy of Canada Ltd., Montreal, PQ (Canada). CANDU Operations

    1994-12-31

    The proceedings of the thirty-fourth annual conference of the Canadian Nuclear Association contain 23 complete papers and three speeches organized in the following sessions: opening, plenary, new environmental regulations and their effect on the energy industry, CANDU update, life cycle management of nuclear power plants, evolution of nuclear technology, technologies for tomorrow, nuclear used fuel and disposal of low-level waste, world economics and energy consumption. The complete papers have been abstracted separately.

  5. Supply of nuclear materials

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1959-07-15

    Any large-scale atomic energy programme is inherently dependent on the availability of materials that can be used as fuel in reactors, and the International Atomic Energy Agency, at its inception, was intended to act as a bank for the flow of materials between Member States. According to its Statute, one of its primary functions is to provide materials 'to meet the needs of research on, and development and practical application of, atomic energy for peaceful purposes, including the production of electric power, with due consideration for the needs of the under-developed areas of the world'. If the Agency is to fulfil its Statutory function, it would be essential for it to have not only some ready sources of supply, but also an established framework of general terms and conditions on which it could secure the supplies. The latter would eliminate the need for going through elaborate procedural formalities whenever the Agency receives a new request for materials. Such a framework has now been established with the signing of broad agreements with three countries which had offered to supply various quantities of special fissionable materials to the Agency. These agreements, signed in Vienna on 11 May 1959, with the USSR, the UK and the USA, lay down the basic terms and conditions on which these three countries will make nuclear materials available when needed by the Agency. The USSR has agreed to make available to the Agency 50 kg of uranium-235, the UK 20 kg and the USA 5 000 kg. The material will be supplied in the form of enriched uranium in any concentration up to 20 per cent; the amounts mentioned relate to the 235-isotope content of the materials. The UK and the USA have agreed that the parties to a particular supply agreement may decide on higher enrichment of uranium to be used for research reactors, material testing reactors or for other research purposes. The USA has also agreed to make available to the Agency such additional supplies as would match in amount

  6. Proceedings of the Jorge Andre Swieca Summer School; 4. Experimental Nuclear Physics Session

    International Nuclear Information System (INIS)

    1990-01-01

    These proceedings present works on experimental nuclear physics, activation analysis, nuclear interactions, neutron physics, nuclear moments, inelastic scattering, lattices and chemical analysis. (L.C.J.A.)

  7. Automated Systems for Safeguarding and Accountancy of Stored Nuclear Material (for proceedings of ESARDA 21st Annual Meeting, Sevilla, Spain May 4-6, 1999

    International Nuclear Information System (INIS)

    Baldwin, K.M.; Bell, Z.W.; Dunigan, J.J.; Gaby, J.E.; Hickerson, T.W.; Lawson, R.L.; Miller, M.A.; Mooney, L.R.; Pickett, C.A.; Seiber, L.E.; Younkin, J.R.

    1999-01-01

    Oak Ridge has developed several sensor systems that are capable of providing unattended monitoring of the physical and/or assigned attributes associated with stored nuclear materials. These systems include the Continuous Automated Vault Inventory System (CAVISTM), SmartShelfTM, and the ReflectoActive Seal System TM. Each of these systems can be implemented independently or may be integrated with existing systems through the Graphical Facility Information Center or GraFICTM software package. GraFICTM is a versatile software package designed to operate in a distributed computing environment. GraFICTM can monitor and report all item and facility activity from the various sensors and systems to an unlimited number of authorized remote clients through a common interface. The software also contains an Intelligent Facility Management (lFM) package that helps storage facility managers with space planning, records management, item location, and variety of other facility specific needs. Results and details from several system deployments will be described, along with the specific features and possible uses of each system

  8. Proceeding of the Scientific Presentation on Nuclear Fuel Cycle

    International Nuclear Information System (INIS)

    Suripto, A.; Yuwono, I.; Nasution, H.; Hersubeno, B.J.; Amini, S.; Sigit; Cahyono, A.

    1996-11-01

    The proceeding contains papers presented on Scientific Presentation on Nuclear Fuel Cycle held in Jakarta, 18-19 March 1996. These are 46 papers resulted from scientific works on various disciplines which have supported to nuclear fuel cycle activities both in and outside National Atomic Energy Agency of Indonesia.(ID)

  9. Proceedings of the second Scientific Presentation on Nuclear Fuel Cycle

    International Nuclear Information System (INIS)

    Suripto, A.; Yuwono, I.; Badruzzaman, M; Nasution, H.; Kusnowo, A; Sigit; Amini, S.

    1998-01-01

    The proceeding contains papers presented on Scientific Presentation on Nuclear Fuel Cycle held in Jakarta, 19-20 November 1996. These papers form a scientific works on various disciplines which have supported to nuclear fuel cycle activities both in and outside National Atomic Energy Agency of Indonesia. There are 48 papers indexed individually. (ID)

  10. Proceedings of the Canadian Nuclear Society 15. annual conference

    International Nuclear Information System (INIS)

    Huynh, H.M.

    1994-01-01

    The proceedings of the 15. annual conference of the Canadian Nuclear Society cover a wide range of nuclear topics, but the emphasis is on CANDU reactors and Canadian experience. The 89 papers are arranged in 17 sessions dealing with the following subjects: thermalhydraulics, fuel channels, operations, reactor physics, fuel, new technology, safety, training, waste management. The individual papers have been abstracted separately

  11. Proceedings of the Canadian Nuclear Society 15. annual conference

    Energy Technology Data Exchange (ETDEWEB)

    Huynh, H M [Hydro-Quebec, Montreal, PQ (Canada)

    1994-12-31

    The proceedings of the 15. annual conference of the Canadian Nuclear Society cover a wide range of nuclear topics, but the emphasis is on CANDU reactors and Canadian experience. The 89 papers are arranged in 17 sessions dealing with the following subjects: thermalhydraulics, fuel channels, operations, reactor physics, fuel, new technology, safety, training, waste management. The individual papers have been abstracted separately.

  12. Proceedings of the Conference on 75 years of Nuclear Fission

    Indian Academy of Sciences (India)

    Proceedings of the Conference on 75 years of Nuclear Fission: Present Status and Future Perspectives (Fission75) - Part I. pp 187-188. Organizing Committee · More Details Fulltext PDF. pp 189-190. Foreword · D C Biswas K Mahata V M Datar · More Details Fulltext PDF. pp 191-198. Seventy-five years of nuclear fission.

  13. Proceedings of the first internet symposium on nuclear data

    Energy Technology Data Exchange (ETDEWEB)

    Fukahori, Tokio; Iwamoto, Osamu; Nakagawa, Tsuneo [eds.] [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1997-03-01

    The First Internet Symposium on Nuclear Data (ISND-1) was held on the WWW home page of Nuclear Data Center at Tokai Research Establishment, Japan Atomic Energy Research Institute (JAERI), from April 8 to June 15, 1996. This symposium was organized by Japanese Nuclear Data Committee and Nuclear Data Center, JAERI and was the first trial to use `Internet` for the symposium in a nuclear data field. In ISND-1, presented were 25 papers on various topics of nuclear data. Those presented papers are compiled in this proceedings as well as brief description about management of ISND-1. (author)

  14. Proceedings of the first internet symposium on nuclear data

    International Nuclear Information System (INIS)

    Fukahori, Tokio; Iwamoto, Osamu; Nakagawa, Tsuneo

    1997-03-01

    The First Internet Symposium on Nuclear Data (ISND-1) was held on the WWW home page of Nuclear Data Center at Tokai Research Establishment, Japan Atomic Energy Research Institute (JAERI), from April 8 to June 15, 1996. This symposium was organized by Japanese Nuclear Data Committee and Nuclear Data Center, JAERI and was the first trial to use 'Internet' for the symposium in a nuclear data field. In ISND-1, presented were 25 papers on various topics of nuclear data. Those presented papers are compiled in this proceedings as well as brief description about management of ISND-1. (author)

  15. Proceedings of the Sixth Arab Conference on the Peaceful Uses of Atomic Energy, Vol.II. Scientific Presentation (Reactors, Materials, Fuel Cycles and Nuclear Safety)

    International Nuclear Information System (INIS)

    2003-10-01

    The publication has been set up as a textbook for researching dealing with health protection during work with Human needs of Nuclear Science and applications. The book consists of the following chapters: Personnel and working environment monitoring; analytical techniques; radiation protection harmonized and integrated policy for the arab country; Nuclear safety; fuel cycles; nuclear medicine; accelerators; medical applications; radiation chemistry; hydrology; environmental studies; biological effects of ionizing radiation on agriculture; radiation accidents

  16. Proceedings of the Sixth Arab Conference on the Peaceful Uses of Atomic Energy, Vol.II. Scientific Presentation (Reactors, Materials, Fuel Cycles and Nuclear Safety)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-10-01

    The publication has been set up as a textbook for researching dealing with health protection during work with Human needs of Nuclear Science and applications. The book consists of the following chapters: Personnel and working environment monitoring; analytical techniques; radiation protection harmonized and integrated policy for the arab country; Nuclear safety; fuel cycles; nuclear medicine; accelerators; medical applications; radiation chemistry; hydrology; environmental studies; biological effects of ionizing radiation on agriculture; radiation accidents.

  17. Proceedings of the 8. Australian conference on nuclear techniques of analysis

    International Nuclear Information System (INIS)

    1993-01-01

    These proceedings contain the abstracts or extended abstracts of 72 out of 77 presentations. The topics focus on instrumentation, nuclear techniques and their applications for material science, surfaces, archaeometry, art, geological, environmental and biomedical studies. An outline of the Australian facilities available for research purposes is also provided. Separate abstracts were prepared for the individual papers in this volume

  18. Proceedings of the 8. Australian conference on nuclear techniques of analysis

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    These proceedings contain the abstracts or extended abstracts of 72 out of 77 presentations. The topics focus on instrumentation, nuclear techniques and their applications for material science, surfaces, archaeometry, art, geological, environmental and biomedical studies. An outline of the Australian facilities available for research purposes is also provided. Separate abstracts were prepared for the individual papers in this volume.

  19. Proceedings of the 8. Australian conference on nuclear techniques of analysis

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    These proceedings contain the abstracts or extended abstracts of 72 out of 77 presentations. The topics focus on instrumentation, nuclear techniques and their applications for material science, surfaces, archaeometry, art, geological, environmental and biomedical studies. An outline of the Australian facilities available for research purposes is also provided. Separate abstracts were prepared for the individual papers in this volume.

  20. Transportation of nuclear materials

    International Nuclear Information System (INIS)

    Brobst, W.A.

    1977-01-01

    Twenty years of almost accident-free transport of nuclear materials is pointed to as evidence of a fundamentally correct approach to the problems involved. The increased volume and new technical problems in the future will require extension of these good practices in both regulations and packaging. The general principles of safety in the transport of radioactive materials are discussed first, followed by the transport of spent fuel and of radioactive waste. The security and physical protection of nuclear shipments is then treated. In discussing future problems, the question of public understanding and acceptance is taken first, thereafter transport safeguards and the technical bases for the safety regulations. There is also said to be a need for a new technology for spent fuel casks, while a re-examination of the IAEA transport standards for radiation doses is recommended. The IAEA regulations regarding quality assurance are said to be incomplete, and more information is required on correlations between engineering analysis, scale model testing and full scale crash testing. Transport stresses on contents need to be considered while administrative controls have been neglected. (JIW)

  1. Fourth Regional Meeting: Nuclear Energy in Central Europe, Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Mavko, B; Cizelj, L [eds.; Nuclear Society of Slovenia (Slovenia)

    1997-07-01

    Fourth Regional Meeting for Nuclear Energy in Central Europe is an annual meeting of the Nuclear Society of Slovenia. The proceedings contain 89 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region. Topics are: Research Reactors, Reactor Physics, Probabilistic Safety Assessment, Severe Accidents, Ageing and Integrity, Thermal Hydraulics, NPP Operation Experiance, Radioactive Waste Management, Environment and Other Aspects, Public and Nuclear Energy, SG Replacement and Plant Uprating.

  2. Proceedings of the 2003 symposium on nuclear data

    International Nuclear Information System (INIS)

    Ohsawa, Takaaki; Fukahori, Tokio

    2004-04-01

    The 2003 Symposium on Nuclear Data was held at Tokai Research Establishment, Japan Atomic Energy Research Institute (JAERI), on 27th and 28th of November 2003. Japanese Nuclear Data Committee and Nuclear Data Center, JAERI organized this symposium. In the oral sessions, presented were 18 papers on topics of ADS development and nuclear data for transmutation, nuclear data needs for next generation reactors and future JENDL plan, frontier of nuclear physics studies and nuclear data measurements, advanced science study and nuclear data, nuclear data needs and activities in Asian region, future of nuclear data study and other subjects. In the poster session, presented were 25 papers concerning experiments, evaluations, benchmark tests and so on. Those presented papers are compiled in the proceedings. The 43 of the presented papers are indexed individually. (J.P.N.)

  3. Modernization of instrumentation and control systems in nuclear power plants. Working materials. Proceedings of a specialists` meeting held in Garching, Germany, 4-7 July 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    The Specialists` Meeting on ``Modernization of Instrumentation and Control Systems in Nuclear Power Plants`` was organized by the IAEA (jointly by Division of Nuclear Power and Division of Nuclear Safety) in co-operation with Institute for Safety Technology (ISTec) and held in Garching, Germany from 4 to 7 July 1995 (The Meeting Chairman - Dr. W. Bastl). The meeting brought together experts on power plant operation with experts on application of today`s instrumentation and control technology. In this way, a match was made between those knowing the industry needs and requirements and those knowing the potentials of the technology. Refs, figs and tabs.

  4. Proceedings: 2001 Nuclear Asset Management Workshop

    International Nuclear Information System (INIS)

    2002-01-01

    The fourth annual EPRI Nuclear Asset Management Workshop helped decision makers at all levels of nuclear enterprises to keep informed about developing nuclear asset management (NAM) processes, methods, and tools. The goal is to operate nuclear plants with enhanced profitability, while maintaining safety

  5. Proceedings of the 2002 symposium on nuclear data

    Energy Technology Data Exchange (ETDEWEB)

    Ohsawa, Takaaki [Kinki Univ., Higashi-Osaka, Osaka (Japan); Fukahori, Tokio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2003-06-01

    The 2002 Symposium on Nuclear Data was held at Tokai Research Establishment, Japan Atomic Energy Research Institute (JAERI), on 21st and 22nd of November 2002. Japanese Nuclear Data Committee and Nuclear Data Center, JAERI organized this symposium. In the oral sessions, presented were 18 papers on topics of release of JENDL-3.3, requests from users, status of FP nuclear data, international activities and other subjects. In the poster session, presented were 33 papers concerning experiments, evaluations, benchmark tests and on-line database on nuclear data. Those presented papers are compiled in the proceedings. (author)

  6. Proceedings of the 1999 symposium on nuclear data

    Energy Technology Data Exchange (ETDEWEB)

    Yamano, Naoki; Fukahori, Tokio [eds.

    2000-03-01

    The 1999 Symposium on Nuclear Data was held at Tokai Research Establishment, Japan Atomic Energy Research Institute (JAERI), on 18th and 19th of November 1999. Japanese Nuclear Data Committee and Nuclear Data Center, JAERI organized this symposium. In the oral sessions, presented papers were on keynote address, nuclear data measurement for long-lived RI and in medium energy region, status of JENDL, international session and other topics. In the poster session, presented papers were concerning experiments, evaluations, benchmark tests and on-line database on nuclear data. Those presented papers are compiled in the proceedings. The 64 of the presented papers are indexed individually. (J.P.N.)

  7. Proceedings of the Canadian Nuclear Society 12. annual conference

    International Nuclear Information System (INIS)

    1991-01-01

    This volume contains the Proceedings of the seventeen Technical Sessions from the Twelfth Annual Conference of the Canadian Nuclear Society held in Saskatoon, Saskatchewan, June 9 to 12, 1991. As in previous years, the Annual Conference of the Canadian Nuclear Society was held in conjunction with the Annual Conference of the Canadian Nuclear Association. The major topics of discussion included: reactor physics; thermal hydraulics; industrial irradiation; computer applications; fuel channel analysis; small reactors; severe accidents; fuel behaviour under accident conditions; reactor components; safety related computer software; nuclear fuel management; nuclear waste management; and, uranium mining processing

  8. Nuclear Electronics I. Proceedings of the Conference on Nuclear Electronics. Vol. I

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1962-04-15

    Nuclear instruments are used in almost every phase of atomic energy work, from assessing health hazards and prospecting for nuclear materials to plant control and nuclear physics experiments. The demands on nucleonic instrumentation are growing steadily. High-energy particle physics need such instruments for measuring extremely short times; in various research experiments most advanced electronic systems are required; and routine applications of radioisotopes call for more reliable instruments for automated counting facilities. In order to give designers and users of nuclear instrumentation an opportunity to discuss the research results and to exchange information on recent developments and new designs, the International Atomic Energy Agency, in co-operation with the Federal Nuclear Energy Commission of Yugoslavia, organized a Conference on Nuclear Electronics which was held in Belgrade from 15-20 May 1961. It was attended by more than 300 scientists from nearly 30 countries and five international organizations. Over 150 papers were read and discussed. As the field of nuclear electronics has expanded considerably, it was impossible to discuss all aspects of nuclear electronics in one series of meetings. Included in the main topics were radiation detectors, electronic circuitry in conventional and fast-pulse techniques and advanced electronic systems used in nuclear research. The Proceedings presented in these volumes contain the full records of the Conference, including discussions. The present state of technique, together with current trends and developments, are outlined. Of particular value should be the world-wide survey on progress recently made in such fields as those connected with semiconductor detectors, spark counters, luminescence chambers and fast electronic facilities for nuclear physics research. Together with the Proceedings of the Symposium on the same subject held in Paris and also published by the International Atomic Energy Agency, these volumes

  9. Nuclear Electronics II. Proceedings of the Conference on Nuclear Electronics. V. II

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1962-04-15

    Nuclear instruments are used in almost every phase of atomic energy work, from assessing health hazards and prospecting for nuclear materials to plant control and nuclear physics experiments. The demands on nucleonic instrumentation are growing steadily. High-energy particle physics need such instruments for measuring extremely short times; in various research experiments most advanced electronic systems are required; and routine applications of radioisotopes call for more reliable instruments for automated counting facilities. In order to give designers and users of nuclear instrumentation an opportunity to discuss the research results and to exchange information on recent developments and new designs, the International Atomic Energy Agency, in co-operation with the Federal Nuclear Energy Commission of Yugoslavia, organized a Conference on Nuclear Electronics which was held in Belgrade from 15-20 May 1961. It was attended by more than 300 scientists from nearly 30 countries and five international organizations. Over 150 papers were read and discussed. As the field of nuclear electronics has expanded considerably, it was impossible to discuss all aspects of nuclear electronics in one series of meetings. Included in the main topics were radiation detectors, electronic circuitry in conventional and fast-pulse techniques and advanced electronic systems used in nuclear research. The Proceedings presented in these volumes contain the full records of the Conference, including discussions. The present state of technique, together with current trends and developments, are outlined. Of particular value should be the world-wide survey on progress recently made in such fields as those connected with semiconductor detectors, spark counters, luminescence chambers and fast electronic facilities for nuclear physics research. Together with the Proceedings of the Symposium on the same subject held in Paris and also published by the International Atomic Energy Agency, these volumes

  10. Nuclear Electronics III. Proceedings of the Conference on Nuclear Electronics. V. III

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1962-04-15

    Nuclear instruments are used in almost every phase of atomic energy work, from assessing health hazards and prospecting for nuclear materials to plant control and nuclear physics experiments. The demands on nucleonic instrumentation are growing steadily. High-energy particle physics need such instruments for measuring extremely short times; in various research experiments most advanced electronic systems are required; and routine applications of radioisotopes call for more reliable instruments for automated counting facilities. In order to give designers and users of nuclear instrumentation an opportunity to discuss the research results and to exchange information on recent developments and new designs, the International Atomic Energy Agency, in co-operation with the Federal Nuclear Energy Commission of Yugoslavia, organized a Conference on Nuclear Electronics which was held in Belgrade from 15-20 May 1961. It was attended by more than 300 scientists from nearly 30 countries and five international organizations. Over 150 papers were read and discussed. As the field of nuclear electronics has expanded considerably, it was impossible to discuss all aspects of nuclear electronics in one series of meetings. Included in the main topics were radiation detectors, electronic circuitry in conventional and fast-pulse techniques and advanced electronic systems used in nuclear research. The Proceedings presented in these volumes contain the full records of the Conference, including discussions. The present state of technique, together with current trends and developments, are outlined. Of particular value should be the world-wide survey on progress recently made in such fields as those connected with semiconductor detectors, spark counters, luminescence chambers and fast electronic facilities for nuclear physics research. Together with the Proceedings of the Symposium on the same subject held in Paris and also published by the International Atomic Energy Agency, these volumes

  11. Study of nuclear material accounting

    International Nuclear Information System (INIS)

    Ruderman, H.

    1977-01-01

    The implications of deliberate diversion of nuclear materials on materials accounting, the validity of the MUF concept to establish assurance concerning the possible diversion of special nuclear materials, and an economic analysis to permit cost comparison of varying the inventory frequency are being studied. An inventory cost model, the statistical hypothesis testing approach, the game theoretic approach, and analysis of generic plants are considered

  12. Proceedings of the 3. General Congress on Nuclear Energy. v. 9

    International Nuclear Information System (INIS)

    1990-01-01

    The Proceedings of the 3. General Congress on Nuclear Energy (CGEN), present about 200 contributed papers. The topics covered by the meeting are: reactor physics and operation; risk analysis, safety analysis, nuclear power plants construction; thermohydraulics; nuclear power plants control and instrumentation; equipment and system design, radioactive management; fuel cycle; design and fabrication of fuel elements, science and technology materials; instrumentation for radiation detection and dosimetry; shielding, radiation protection, licensing, safeguards, social and environmental impacts; radioisotopes production and application; radiochemistry, radioecology; nuclear medicine and radiobiology. In this volume the contributed papers emphasize the topics shielding, radiation protection, licensing, safeguards and social and environmental impacts. (M.I.A.)

  13. Global nuclear material control model

    International Nuclear Information System (INIS)

    Dreicer, J.S.; Rutherford, D.A.

    1996-01-01

    The nuclear danger can be reduced by a system for global management, protection, control, and accounting as part of a disposition program for special nuclear materials. The development of an international fissile material management and control regime requires conceptual research supported by an analytical and modeling tool that treats the nuclear fuel cycle as a complete system. Such a tool must represent the fundamental data, information, and capabilities of the fuel cycle including an assessment of the global distribution of military and civilian fissile material inventories, a representation of the proliferation pertinent physical processes, and a framework supportive of national or international perspective. They have developed a prototype global nuclear material management and control systems analysis capability, the Global Nuclear Material Control (GNMC) model. The GNMC model establishes the framework for evaluating the global production, disposition, and safeguards and security requirements for fissile nuclear material

  14. Proceeding of the 7. Seminar on Technology and Safety of Nuclear Power Plants and Nuclear Facilities

    International Nuclear Information System (INIS)

    Hastowo, Hudi; Antariksawan, Anhar R.; Soetrisnanto, Arnold Y; Jujuratisbela, Uju; Aziz, Ferhat; Su'ud, Zaki; Suprawhardana, M. Salman

    2002-02-01

    The seventh proceedings of seminar safety and technology of nuclear power plant and nuclear facilities, held by National Nuclear Energy Agency. The Aims of seminar is to exchange and disseminate information about safety and nuclear Power Plant Technology and Nuclear Facilities consist of technology; high temperature reactor and application for national development sustain able and high technology. This seminar level all aspects technology, Power Reactor research reactor, high temperature reactor and nuclear facilities. The article is separated by index

  15. Nuclear tests and health: conference proceedings

    International Nuclear Information System (INIS)

    Beaudeau, M.C.

    2002-01-01

    This conference was organized by the observatory of French nuclear weapons - CDRPC-, the 'Moruroa e Tatou' association and the association of nuclear test veterans. Its aim was to call upon the victims of nuclear tests to speak about their health problems and to the possible consequences on their children's health. It pleads in favour of a particular legislation and in favour of the creation of an organization which would take for responsibility the health and environmental impacts of nuclear tests. (J.S.)

  16. Public enlightment seminar on nuclear power. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Yildirim, N

    1998-12-31

    The seminar considered different aspects of nuclear power development, including the following issues: electricity generation, power supply and demand, energy sources, consumption of electricity, energy outlook in Europe, comparative analysis of energy options, safety of modern nuclear power plants, radiation and human health, radioactive waste management, nuclear techniques to promote world food security, public information issues.

  17. Public enlightment seminar on nuclear power. Proceedings

    International Nuclear Information System (INIS)

    Yildirim, N.

    1997-01-01

    The seminar considered different aspects of nuclear power development, including the following issues: electricity generation, power supply and demand, energy sources, consumption of electricity, energy outlook in Europe, comparative analysis of energy options, safety of modern nuclear power plants, radiation and human health, radioactive waste management, nuclear techniques to promote world food security, public information issues

  18. Proceedings of the 1991 symposium on nuclear data

    Energy Technology Data Exchange (ETDEWEB)

    Baba, Mamoru [Tokyo Univ. (Japan); Nakagawa, Tsuneo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Japanese Nuclear Data Committee

    1992-03-15

    The 1991 Symposium on Nuclear data was held at Tokai Research Establishment, Japan Atomic Energy Research Institute (JAERI), on 28th and 29th of November 1991. This symposium was organized by Japanese Nuclear Data Committee and Nuclear Data Center, JAERI. In the oral session, presented were 15 papers on nuclear data activities in Thailand, status reviews of JENDL-3 and its special purpose files, OMEGA program and ESNIT promoted by JAERI and related nuclear data, reviews of nuclear theories, nuclear data in the intermediate energy region, topics on knowledge technology and reactor physics. In the poster session, twenty-three papers were presented, which were related to nuclear data measurements, benchmark tests of evaluated data and evaluation. All of the 38 papers are compiled in the proceedings.

  19. Operating procedures for nuclear power plants and their presentation. Working material. Proceedings of a specialists meeting held in Vienna, 31 March - 2 April 1992

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    With a view to exchanging information on most recent development of technology in the field the IAEA International Working Group on Nuclear Power Plant control and Instrumentation suggested to organize a Specialists` Meeting on ``Operating Procedures for Nuclear Power Plants and their Presentation``. The meeting was held in Vienna, at IAEA Headquarters from March 31 to April 2, 1992 and provided an opportunity to: share operators experience; discuss the different techniques of presenting the information; identify further trends of technology and needs of the industry. The meeting was attended by 46 participants representing 12 Member States and 3 international organizations. The present volume contains summary of the meeting, session summaries and papers of the national participants. Refs, figs and tabs.

  20. Operating procedures for nuclear power plants and their presentation. Working material. Proceedings of a specialists meeting held in Vienna, 31 March - 2 April 1992

    International Nuclear Information System (INIS)

    1993-01-01

    With a view to exchanging information on most recent development of technology in the field the IAEA International Working Group on Nuclear Power Plant control and Instrumentation suggested to organize a Specialists' Meeting on ''Operating Procedures for Nuclear Power Plants and their Presentation''. The meeting was held in Vienna, at IAEA Headquarters from March 31 to April 2, 1992 and provided an opportunity to: share operators experience; discuss the different techniques of presenting the information; identify further trends of technology and needs of the industry. The meeting was attended by 46 participants representing 12 Member States and 3 international organizations. The present volume contains summary of the meeting, session summaries and papers of the national participants. Refs, figs and tabs

  1. Proceedings of the IAEA research coordination meeting on methods for the calculations of neutron nuclear data for structural materials, Bologna, Italy, 7-10 October 1986

    International Nuclear Information System (INIS)

    Goulo, V.

    1988-01-01

    The Meeting presentations were divided into 5 sessions devoted to the following aspects of nuclear theory for evaluation of fast neutron data: Development of Multistep Compound Reaction Models (3 papers), Exiton, Hybrid, Unified Pre-equilibrium Models (4 papers), Description of Direct Processes (3 papers), Parametrization of Optical Model, Level Density Functions, Gamma-Ray Strength Functioning (3 papers) and Methods of Cross Section Evaluation (5 papers). A separate abstract was prepared for each of these papers. Refs, figs and tabs

  2. European Society of Nuclear Methods in Agriculture. Proceedings

    International Nuclear Information System (INIS)

    The conference proceedings reported include papers on the Czechoslovak nuclear programme in the field of agriculture and food industry, the application of stable isotopes in agriculture, the applications of radioanalytical methods in agriculture, the use of waste heat from nuclear power plants, food irradiation, waste processing by irradiation, radiation-induced stimulation effects in plants, tracer techniques in animal science, radiation analysis, the use of nuclear techniques in the study of soil-plant relationships, applied mutagenesis, environmental pollution, genetic methods of pest control, the applications of radioisotopes in insect ecology, and the application of nuclear methods in plant physiology. (J.B.)

  3. Proceedings of the first annual Nuclear Criticality Safety Technology Project

    International Nuclear Information System (INIS)

    Rutherford, D.A.

    1994-09-01

    This document represents the published proceedings of the first annual Nuclear Criticality Safety Technology Project (NCSTP) Workshop, which took place May 12--14, 1992, in Gaithersburg, Md. The conference consisted of four sessions, each dealing with a specific aspect of nuclear criticality safety issues. The session titles were ''Criticality Code Development, Usage, and Validation,'' ''Experimental Needs, Facilities, and Measurements,'' ''Regulation, Compliance, and Their Effects on Nuclear Criticality Technology and Safety,'' and ''The Nuclear Criticality Community Response to the USDOE Regulations and Compliance Directives.'' The conference also sponsored a Working Group session, a report of the NCSTP Working Group is also presented. Individual papers have been cataloged separately

  4. Proceedings of the 1989 seminar on nuclear data

    International Nuclear Information System (INIS)

    Nakajima, Yutaka; Igashira, Masayuki

    1990-02-01

    The 1989 Seminar no Nuclear Data was held at Tokai Research Establishment of Japan Atomic Energy Research Institute, on November 16 and 17, 1989. This Seminar was organized by Japanese Nuclear Data Committee (JNDC) and Nuclear Data Center, JAERI. In an oral session, review and benchmark tests of JENDL-3 were presented, which were followed by lively discussion. Data need of other nuclear data than neutron induced reaction data were also presented. In addition, several topical talks were given. In a poster session, twenty papers on evaluation and measurement was presented and fruitful discussions were made. In this proceedings, thirty-four papers given in the seminar are compiled. (author)

  5. Proceedings of the international nuclear power plant aging symposium

    International Nuclear Information System (INIS)

    Beranek, A.

    1989-03-01

    This report presents the proceedings of the International Nuclear Power Plant Aging Symposium that was held at the Hyatt Regency Hotel in Bethesda, Maryland, on August 30-31 and September 1, 1988. The Symposium was presented in cooperation with the American Nuclear Society, the American Society of Civil Engineers, the American Society of Mechanical Engineers, and the Institute of Electrical and Electronics Engineers. There were approximately 550 participants from 16 countries at the Symposium

  6. Third Regional Meeting: Nuclear Energy in Central Europe, Proceedings

    International Nuclear Information System (INIS)

    Stritar, A.; Jencic, I.

    1996-01-01

    Third Regional Meeting for Nuclear Energy in Central Europe is an annual meeting of the Nuclear Society of Slovenia. The proceedings contain 71 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region. Topics are: Research Reactors, Reactor Physics, Probabilistic Safety Assessment, Severe Accident management, Thermal Hydraulics, NPP Operation, Radioactive Waste Management, Main Components Integrity, Environment and Other Aspects and Public Information

  7. Third Regional Meeting: Nuclear Energy in Central Europe, Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Stritar, A; Jencic, I [Nuclear Society of Slovenia (Slovenia); eds.

    1996-07-01

    Third Regional Meeting for Nuclear Energy in Central Europe is an annual meeting of the Nuclear Society of Slovenia. The proceedings contain 71 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region. Topics are: Research Reactors, Reactor Physics, Probabilistic Safety Assessment, Severe Accident management, Thermal Hydraulics, NPP Operation, Radioactive Waste Management, Main Components Integrity, Environment and Other Aspects and Public Information.

  8. Proceedings of the 1986 seminar on nuclear data

    Energy Technology Data Exchange (ETDEWEB)

    Nakagawa, Tsuneo; Asami, Tetsuo [eds.

    1987-02-15

    The seminar focused on problems with nuclear data and reactor constants and their sensitivity analyses. The poster session concerned recent measurements of neutron cross sections and computer codes for theoretical calculations. Separate abstracts were prepared for 34 papers in these proceedings. (DWL)

  9. Proceedings of the Nuclear Criticality Technology and Safety Project Workshop

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez, R.G. [comp.

    1994-01-01

    This report is the proceedings of the annual Nuclear Criticality Technology and Safety Project (NCTSP) Workshop held in Monterey, California, on April 16--28, 1993. The NCTSP was sponsored by the Department of Energy and organized by the Los Alamos Critical Experiments Facility. The report is divided into six sections reflecting the sessions outlined on the workshop agenda.

  10. Proceedings of the Nuclear Criticality Technology and Safety Project Workshop

    International Nuclear Information System (INIS)

    Sanchez, R.G.

    1994-01-01

    This report is the proceedings of the annual Nuclear Criticality Technology and Safety Project (NCTSP) Workshop held in Monterey, California, on April 16--28, 1993. The NCTSP was sponsored by the Department of Energy and organized by the Los Alamos Critical Experiments Facility. The report is divided into six sections reflecting the sessions outlined on the workshop agenda

  11. Nuclear materials inventory plan

    International Nuclear Information System (INIS)

    Doerr, R.W.; Nichols, D.H.

    1982-03-01

    In any processing, manufacturing, or active storage facility it is impractical to assume that any physical security system can prevent the diversion of Special Nuclear Material (SNM). It is, therefore, the responsibility of any DOE Contractor, Licensee, or other holder of SNM to provide assurance that loss or diversion of a significant quantity of SNM is detectable. This ability to detect must be accomplishable within a reasonable time interval and can be accomplished only by taking physical inventories. The information gained and decisions resulting from these inventories can be no better than the SNM accounting system and the quality of measurements performed for each receipt, removal and inventory. Inventories interrupt processing or production operations, increase personnel exposures, and can add significantly to the cost of any operation. Therefore, realistic goals for the inventory must be defined and the relationship of the inherent parameters used in its validation be determined. Purpose of this document is to provide a statement of goals and a plan of action to achieve them

  12. Proceedings of the 2005 symposium on nuclear data

    International Nuclear Information System (INIS)

    Tahara, Yoshihisa; Fukahori, Tokio

    2006-11-01

    The 2005 Symposium on Nuclear Data was held at Nuclear Science Research Institute in Tokai Research and Development Center, Japan Atomic Energy Agency (JAEA), on 2nd and 3rd of February 2006. Japanese Nuclear Data Committee and Nuclear Data Center, JAEA organized this symposium. In the oral sessions, presented were 16 papers on topics of nuclear data for the innovative reactor development and upgrade of current light water reactor, the past and future of nuclear data research, capability of the latest evaluated nuclear data files, and recent cross section measurements. In the poster session, presented were 21 papers concerning experiments, evaluations, benchmark tests, applications and so on. A part of those presented papers are compiled in this proceedings. The 36 of the presented papers are indexed individually. (J.P.N.)

  13. Proceedings of the Third Scientific Presentation on Nuclear Fuel Cycle; Prosiding: Presentasi ilmiah daur bahan bakar nuklir 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-02-01

    The proceeding contains papers presented in the Third Scientific Presentation on nuclear Fuel Element Cycle held on 4-5 Nov 1997 in Jakarta, Indonesia. These papers were divided by three groups that are technology of exploration, processing, purification and analysis of nuclear materials; technology of nuclear fuel elements and structures; and technology of waste management, safety and nuclear fuel cycle. There are 38 papers indexed individually. (ID)

  14. Illicit diversion of nuclear materials

    International Nuclear Information System (INIS)

    Bett, F.L.

    1975-08-01

    This paper discusses the means of preventing illegal use of nuclear material by terrorists or other sub-national groups and by governments. With respect to sub-national groups, it concludes that the preventive measures of national safeguards systems, when taken together with the practical difficulties of using nuclear material, would make the diversion and illegal use of nuclear material unattractive in comparison with other avenues open to these groups to attain their ends. It notes that there are only certain areas in the nuclear fuel cycle, e.g. production of some types of nuclear fuel embodying highly enriched uranium and shipment of strategically significant nuclear material, which contain material potentially useful to these groups. It also discusses the difficult practical problems, e.g. coping with radiation, which would face the groups in making use of the materials for terrorist purposes. Concerning illegal use by Governments, the paper describes the role of international safeguards, as applied by the International Atomic Energy Agency, and the real deterrent effect of these safeguards which is achieved through the requirements to maintain comprehensive operating records of the use of nuclear material and by regular inspections to verify these records. The paper makes the point that Australia would not consider supplying nuclear material unless it were subject to international safeguards. (author)

  15. Nuclear material control in Spain

    International Nuclear Information System (INIS)

    Velilla, A.

    1988-01-01

    A general view about the safeguards activities in Spain is presented. The national system of accounting for and control of nuclear materials is described. The safeguards agreements signed by Spain are presented and the facilities and nuclear materials under these agreements are listed. (E.G.) [pt

  16. Nuclear material control in Brazil

    International Nuclear Information System (INIS)

    Marzo, M.A.S.; Iskin, M.C.L.; Palhares, L.C.; Almeida, S.G. de.

    1988-01-01

    A general view about the safeguards activities in Brazil is presented. The national system of accounting for and control of nuclear materials is described. The safeguards agreements signed by Brazil are presented, the facilities and nuclear material under these agreements are listed, and the dificulties on the pratical implementation are discussed. (E.G.) [pt

  17. Nuclear power plant control and instrumentation 1991. Working material. Proceedings of the regular meeting held in Vienna, 6-8 May 1991

    International Nuclear Information System (INIS)

    1992-01-01

    The meeting of the IWG-NPPCI was organized in order to summarize operating experience of nuclear power plant control systems, gain a general overview of activities in development of modern control systems and receive recommendations on the further directions and particular measures within the Agency's programme. The meeting was held at the IAEA Headquarters in Vienna and was attended by twenty four national delegates and observers from 19 countries. The present volume contains: report on the meeting of the IWG-NPPCI, Vienna, 6 to 8 May 1991; report of the scientific secretary on th major activities of IAEA during 1989-91 in the NPPCI area; and reports of the national representatives to the International Working Group on NPPCI. The papers and discussions with practical experience and described actual problems encountered. Emphasis was placed on technical, industrial and economic aspects of the introduction of modern control systems and on the improvement of plant availability and safety. Refs, figs and tabs

  18. Proceedings of the Scientific Meeting and Presentation on Basic Research in Nuclear of the Science and Technology part I : Physics and Nuclear Reactor

    International Nuclear Information System (INIS)

    Kamsul Abraha; Yateman Arryanto; Sri Jauhari S; Agus Taftazani; Kris Tri Basuki; Djoko Sardjono, Ign.; Sukarsono, R.; Samin; Syarip; Suryadi, MS; Sardjono, Y.; Tri Mardji Atmono; Dwiretnani Sudjoko; Tjipto Sujitno, BA.

    2007-08-01

    The Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is a routine activity held by Centre for Accelerator Technology and Material Process, National Nuclear Energy Agency, for monitoring the research activity which achieved in National Nuclear Energy Agency. The Meeting was held in Yogyakarta on July 10, 2007. The proceedings contains papers presented on the meeting about Physics and Nuclear Reactor and there are 52 papers. The proceedings is the first part of the three parts which published in series. (PPIN)

  19. Proceedings of the Scientific Meeting and Presentation on Basic Research in Nuclear of the Science and Technology part II : Nuclear Chemistry and Process Technology

    International Nuclear Information System (INIS)

    Kamsul Abraha; Yateman Arryanto; Sri Jauhari S; Agus Taftazani; Kris Tri Basuki; Djoko Sardjono, Ign.; Sukarsono, R.; Samin; Syarip; Suryadi, MS; Sardjono, Y.; Tri Mardji Atmono; Dwiretnani Sudjoko; Tjipto Sujitno, BA.

    2007-08-01

    The Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is a routine activity held by Centre for Accelerator Technology and Material Process, National Nuclear Energy Agency, for monitoring the research activity which achieved in National Nuclear Energy Agency. The Meeting was held in Yogyakarta on July 10, 2007. The proceedings contains papers presented on the meeting about Nuclear Chemistry and Process Technology and there are 47 papers which have separated index. The proceedings is the second part of the three parts which published in series. (PPIN)

  20. Nuclear materials management storage study

    International Nuclear Information System (INIS)

    Becker, G.W. Jr.

    1994-02-01

    The Office of Weapons and Materials Planning (DP-27) requested the Planning Support Group (PSG) at the Savannah River Site to help coordinate a Departmental complex-wide nuclear materials storage study. This study will support the development of management strategies and plans until Defense Programs' Complex 21 is operational by DOE organizations that have direct interest/concerns about or responsibilities for nuclear material storage. They include the Materials Planning Division (DP-273) of DP-27, the Office of the Deputy Assistant Secretary for Facilities (DP-60), the Office of Weapons Complex Reconfiguration (DP-40), and other program areas, including Environmental Restoration and Waste Management (EM). To facilitate data collection, a questionnaire was developed and issued to nuclear materials custodian sites soliciting information on nuclear materials characteristics, storage plans, issues, etc. Sites were asked to functionally group materials identified in DOE Order 5660.1A (Management of Nuclear Materials) based on common physical and chemical characteristics and common material management strategies and to relate these groupings to Nuclear Materials Management Safeguards and Security (NMMSS) records. A database was constructed using 843 storage records from 70 responding sites. The database and an initial report summarizing storage issues were issued to participating Field Offices and DP-27 for comment. This report presents the background for the Storage Study and an initial, unclassified summary of storage issues and concerns identified by the sites

  1. Nuclear power plant control and instrumentation 1991. Working material. Proceedings of the regular meeting held in Vienna, 6-8 May 1991

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    The meeting of the IWG-NPPCI was organized in order to summarize operating experience of nuclear power plant control systems, gain a general overview of activities in development of modern control systems and receive recommendations on the further directions and particular measures within the Agency`s programme. The meeting was held at the IAEA Headquarters in Vienna and was attended by twenty four national delegates and observers from 19 countries. The present volume contains: report on the meeting of the IWG-NPPCI, Vienna, 6 to 8 May 1991; report of the scientific secretary on th major activities of IAEA during 1989-91 in the NPPCI area; and reports of the national representatives to the International Working Group on NPPCI. The papers and discussions with practical experience and described actual problems encountered. Emphasis was placed on technical, industrial and economic aspects of the introduction of modern control systems and on the improvement of plant availability and safety. Refs, figs and tabs.

  2. Nuclear energy - option for the future. Proceedings

    International Nuclear Information System (INIS)

    1996-01-01

    The goal of this conference was to analyse the future national and international problems arising with energy supplies with regard to the large mass flows and CO 2 flows involved in the use of nuclear energy. The following topics are dealt with: - nuclear energy, world-wide energy management and developments in Europe and Asia - disposal and ultimate waste disposal, plutonium management, an assessment of the Chernobyl accident 10 years on - new reactor developments in the energy mix - the costs arising with nuclear energy in the energy mix. In view of the demand made by climate researchers, to reduce CO 2 , and the additional construction work planned in the eastern and Asian areas, it will remain necessary for the Federal Republic of Germany,too, to maintain the know-how and technology for nuclear energy generation. (orig./DG)

  3. Proceedings of the 1994 nuclear simulation symposium

    Energy Technology Data Exchange (ETDEWEB)

    Laughton, P J [ed.; Atomic Energy of Canada Ltd., Chalk River, ON (Canada). Chalk River Nuclear Labs.

    1994-12-31

    This symposium on nuclear simulation included sessions on reactor physics, on thermalhydraulics, and on fuel and fuel channels of CANDU type reactors. The individual papers have all been abstracted separately.

  4. Nuclear desalination of sea water. Proceedings of an international symposium

    International Nuclear Information System (INIS)

    1997-01-01

    About 250 participants from 24 Member States and seven international organizations took part in the Symposium. A wide variety of topics related to nuclear desalination were reviewed and discussed. These covered the activities of some organizations and institutes, the experience gained in existing nuclear desalination plants and their facilities, national and bilateral programmes, including research, design and development, forecasts for the future and the challenges that lie ahead. It is hoped that the Proceedings will be of value to technical, financial and regulatory decision makers associated with nuclear desalination

  5. Proceedings of the 1992 symposium on nuclear data

    International Nuclear Information System (INIS)

    Baba, Mamoru; Nakagawa, Tsuneo

    1993-03-01

    The 1992 Symposium on Nuclear Data was held at Tokai Research Establishment, Japan Atomic Energy Research Institute (JAERI), on 26th and 27th of November, 1992. The symposium was organized by Japanese Nuclear Data Committee and Nuclear Data Center, JAERI. In the oral session, a total of 15 papers were presented under the sessions of present status of revision work of JENDL-3, adjustment of group constants, nuclear data in medium energy region, nuclear data evaluation method, integral data analyses and topics. In the poster session, presented were 25 papers concerning experiments, evaluations and benchmark tests of nuclear data. Activities of JNDC working groups were also displayed in the poster session. All of the 40 papers except the reports from JNDC working groups are compiled in this proceedings. (author)

  6. Proceedings of the 1992 symposium on nuclear data

    Energy Technology Data Exchange (ETDEWEB)

    Baba, Mamoru [ed.; Tohoku Univ., Sendai (Japan); Nakagawa, Tsuneo [ed.; Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1993-03-15

    The 1992 Symposium on Nuclear Data was held at Tokai Research Establishment, Japan Atomic Energy Research Institute (JAERI), on 26th and 27th of November, 1992. The symposium was organized by Japanese Nuclear Data Committee and Nuclear Data Center, JAERI. The program of the symposium is listed below. In the oral session, a total of 15 papers were presented under the sessions of present status of revision work of JENDL-3, adjustment of group constants, nuclear data in medium energy region, nuclear data evaluation methods, integral data analyses and topics. In the poster session, presented were 25 papers concerning experiments, evaluations and benchmark tests of nuclear data. Activities of JNDC working groups were also displayed in the poster session. All of the 40 papers except the reports from JNDC working groups are compiled in this proceedings.

  7. Nuclear measurements and reference materials

    International Nuclear Information System (INIS)

    1988-01-01

    This report summarizes the progress of the JRC programs on nuclear data, nuclear metrology, nuclear reference materials and non-nuclear reference materials. Budget restrictions and personnel difficulties were encountered during 1987. Fission properties of 235 U as a function of neutron energy and of the resonances can be successfully described on the basis of a three exit channel fission model. Double differential neutron emission cross-sections were accomplished on 7 Li and were started for the tritium production cross-section of 9 Be. Reference materials of uranium minerals and ores were prepared. Special nuclear targets were prepared. A batch of 250 g of Pu0 2 was characterized in view of certification as reference material for the elemental assay of plutonium

  8. Euro hybrid materials and structures. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Hausmann, Joachim M.; Siebert, Marc (eds.)

    2016-08-01

    In order to use the materials as best as possible, several different materials are usually mixed in one component, especially in the field of lightweight design. If these combinations of materials are joined inherently, they are called multi material design products or hybrid structures. These place special requirements on joining technology, design methods and manufacturing and are challenging in other aspects, too. The eight chapters with manuscripts of the presentations are: Chapter 1- Interface: What happens in the interface between the two materials? Chapter 2 - Corrosion and Residual Stresses: How about galvanic corrosion and thermal residual stresses in the contact zone of different materials? Chapter 3 - Characterization: How to characterize and test hybrid materials? Chapter 4 - Design: What is a suitable design and dimensioning method for hybrid structures? Chapter 5 - Machining and Processing: How to machine and process hybrid structures and materials? Chapter 6 - Component Manufacturing: What is a suitable manufacturing route for hybrid structures? Chapter 7 - Non-Destructive Testing and Quality Assurance: How to assure the quality of material and structures? Chapter 8 - Joining: How to join components of different materials?.

  9. Euro hybrid materials and structures. Proceedings

    International Nuclear Information System (INIS)

    Hausmann, Joachim M.; Siebert, Marc

    2016-01-01

    In order to use the materials as best as possible, several different materials are usually mixed in one component, especially in the field of lightweight design. If these combinations of materials are joined inherently, they are called multi material design products or hybrid structures. These place special requirements on joining technology, design methods and manufacturing and are challenging in other aspects, too. The eight chapters with manuscripts of the presentations are: Chapter 1- Interface: What happens in the interface between the two materials? Chapter 2 - Corrosion and Residual Stresses: How about galvanic corrosion and thermal residual stresses in the contact zone of different materials? Chapter 3 - Characterization: How to characterize and test hybrid materials? Chapter 4 - Design: What is a suitable design and dimensioning method for hybrid structures? Chapter 5 - Machining and Processing: How to machine and process hybrid structures and materials? Chapter 6 - Component Manufacturing: What is a suitable manufacturing route for hybrid structures? Chapter 7 - Non-Destructive Testing and Quality Assurance: How to assure the quality of material and structures? Chapter 8 - Joining: How to join components of different materials?

  10. Safety management in nuclear technology. Proceedings

    International Nuclear Information System (INIS)

    2008-01-01

    At the symposium of TueV Sued AG (Munich, Federal Republic of Germany) held in Munich on 28 and 29 October 2008, the following lectures were held: (1) Fundamental requirements of the management system in nuclear technology - Experiences from the international developments at IAEA and WENRA (M. Herttrich); (2) Information from a comparison of requirements of safety management systems (B. Kallenbach-Herbert); (3) Requirements of a modern management system in German nuclear power plants from the view of nuclear safety (D. Majer); (4) Requirements on safety management in module 8 of the regulations project (M. Maqua); (5) Requirements on the management system in nuclear power plants according to GRS-229 and developments at the KTA 1402 ''Integrated management system for safe operation of nuclear power plants (in progress)'' (C. Verstegen); (6) Experiences from the development and implementation of safety management systems in connection with the works management of a nuclear power plant (K. Ramler); (7) Design of a safety management system of a nuclear power plant in consideration of existing management systems (U. Naumann); (8) Experiences in the utilization and evaluation of a safety management system (J. Ritter); (9) Aspects of leadership of safety management systems (S. Seitz); (10) Management of safety or safety management system? Prevailing or administration? (A. Frischknecht); (11) Change management - strategies for successful transfer of new projects: How can I motivate co-workers for a further development of the safety management system? (U. Schnabel); (12) Requirements concerning indicators in integrated management systems and safety management systems (J. Stiller); (13) Integration of proactive and reactive indicators in the safety management system (B. Fahlbruch); (14) What do indicators show? About the use of indicators by regulatory authorities (A. Kern); (15) Safety management and radiation protection in nuclear technology (K. Grantner); (16) Any more

  11. Proceedings of NUCLEAR 2016 the 9th annual international conference on sustainable development through nuclear research and education. Part 1/3

    International Nuclear Information System (INIS)

    Paraschiv, Irina Maria

    2016-01-01

    The Proceedings of the NUCLEAR 2016 international conference on sustainable development through nuclear research and education held at INR-Pitesti on May, 18-20, contain 81 communications presented in two plenary sessions and three sections addressing the themes of Nuclear energy, Environmental protection and Sustainable development. This section (Part 1/3) are addressing the following items: Section 1.1 Nuclear safety and severe accidents (6 papers); Section 1.2 Nuclear reactors and gen. IV (7 papers); Section 1.3 Nuclear technology and materials (29 papers); These papers are presented as abstracts in 'Nuclear 2016 - Book of Abstracts', separately processed

  12. Safety culture in nuclear power plants. Proceedings

    International Nuclear Information System (INIS)

    1994-12-01

    As a consequence of the INSAG-4 report on 'safety culture', published by the IAEA in 1991, the Federal Commission for the Safety of Nuclear Power Plants (KSA) decided to hold a one-day seminar as a first step in this field. The KSA is an advisory body of the Federal Government and the Federal Department of Transport and Energy (EVED). It comments on applications for licenses, observes the operation of nuclear power plants, assists with the preparation of regulations, monitors the progress of research in the field of nuclear safety, and makes proposals for research tasks. The objective of this seminar was to familiarise the participants with the principles of 'safety culture', with the experiences made in Switzerland and abroad with existing concepts, as well as to eliminate existing prejudices. The main points dealt with at this seminar were: - safety culture from the point of view of operators, - safety culture from the point of view of the authorities, - safety culture: collaboration between power plants, the authorities and research organisations, - trends and developments in the field of safety culture. Invitations to attend this seminar were extended to the management boards of companies operating Swiss nuclear power plants, and to representatives of the Swiss authorities responsible for the safety of nuclear power plants. All these organisations were represented by a large number of executive and specialist staff. We would like to express our sincerest thanks to the Head of the Federal Department of Transport and Energy for his kind patronage of this seminar. (author) figs., tabs., refs

  13. Proceedings of computational methods in materials science

    International Nuclear Information System (INIS)

    Mark, J.E. Glicksman, M.E.; Marsh, S.P.

    1992-01-01

    The Symposium on which this volume is based was conceived as a timely expression of some of the fast-paced developments occurring throughout materials science and engineering. It focuses particularly on those involving modern computational methods applied to model and predict the response of materials under a diverse range of physico-chemical conditions. The current easy access of many materials scientists in industry, government laboratories, and academe to high-performance computers has opened many new vistas for predicting the behavior of complex materials under realistic conditions. Some have even argued that modern computational methods in materials science and engineering are literally redefining the bounds of our knowledge from which we predict structure-property relationships, perhaps forever changing the historically descriptive character of the science and much of the engineering

  14. Proceedings of the 2006 symposium on nuclear data

    International Nuclear Information System (INIS)

    Hazama, Taira; Fukahori, Tokio

    2008-09-01

    The 2006 Symposium on Nuclear Data was held at RICOTTI at Tokai-mura, Ibaraki-ken, Japan, on 25th and 26th of January 2007, with about 80 participants. Nuclear Data Division of Atomic Energy Society of Japan organized this symposium with cooperation of North Kanto Branch of the society. In the oral sessions, presented were 6 papers on topics of nuclear data needs for the fission reactor developments and non-energy nuclear applications. In the poster session, presented were 16 papers concerning experiments, evaluations, benchmark tests, applications, and so on. Tutorials on nuclear data, which were for uses of covariance data and MVP code, were also done. Major part of those presented papers is compiled in this proceedings. (author)

  15. Materials. The Argentine nuclear policy

    International Nuclear Information System (INIS)

    Strasser, H.

    1982-01-01

    Part A of the volume contains a literature search on proliferation and the Third World and on the nuclear technology of Argentina. The materials in part B are divided in: 1. Nonproliferation discussion and the Third World. 2. Development and state of nuclear technology in Argentina. 3. Argentina's international contacts in the field of nuclear energy 1. Federal Republic of Germany, 2. Soviet Union, 3. Brazil. (orig./HP) [de

  16. Graphite materials for nuclear reactors

    International Nuclear Information System (INIS)

    Oku, Tatsuo

    1991-01-01

    Graphite materials have been used in the nuclear fission reactors from the beginning of the reactor development for the speed reduction and reflection of neutron. Graphite materials are used both as a moderator and as a reflector in the core of high temperature gas-cooled reactors, and both as a radiation shielding material and as a reflector in the surrounding of the core for the fast breeder reactor. On the other hand, graphite materials are being positively used as a first wall of plasma as it is known that low Z materials are useful for holding high temperature plasma in the nuclear fusion devices. In this paper the present status of the application of graphite materials to the nuclear fission reactors and fusion devices (reactors) is presented. In addition, a part of results on the related properties to the structural design and safety evaluation and results examined on the subjects that should be done in the future are also described. (author)

  17. Fossil Energy Materials Program conference proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Judkins, R.R. (comp.)

    1987-08-01

    The US Department of Energy Office of Fossil Energy has recognized the need for materials research and development to assure the adequacy of materials of construction for advanced fossil energy systems. The principal responsibility for identifying needed materials research and for establishing a program to address these needs resides within the Office of Technical Coordination. That office has established the Advanced Research and Technology Development (AR and TD) Fossil Energy Materials Program to fulfill that responsibility. In addition to the AR and TD Materials Program, which is designed to address in a generic way the materials needs of fossil energy systems, specific materials support activities are also sponsored by the various line organizations such as the Office of Coal Gasification. A conference was held at Oak Ridge, Tennessee on May 19-21, 1987, to present and discuss the results of program activities during the past year. The conference program was organized in accordance with the research thrust areas we have established. These research thrust areas include structural ceramics (particularly fiber-reinforced ceramic composites), corrosion and erosion, and alloy development and mechanical properties. Eighty-six people attended the conference. Papers have been entered individually into EDB and ERA. (LTN)

  18. Nuclear spectroscopy with direct relations II. Proceedings

    International Nuclear Information System (INIS)

    Throw, F. E.

    1964-01-01

    The Symposium on Nuclear Spectroscopy with Direct Reactions, sponsored and organized by Argonne National Laboratory under the auspices of the U. S. Atomic Energy Commission, was held on 9-11 March 1964 at the Center for Continuing Education, University of Chicago. The present volume contains the invited papers along with abstracts or summaries of the few short papers selected for their special relevance to the topics of the invited lecturers . Edited versions of the discussions are also included

  19. Proceedings of the eleventh annual conference on fossil energy materials

    Energy Technology Data Exchange (ETDEWEB)

    Judkins, R.R. [comp.

    1997-12-01

    The objective of the Advanced Research and Technology Development (AR and TD) Materials Program is to conduct research and development on materials for longer-term fossil energy applications as well as for generic needs of various fossil fuel technologies. These proceedings contain 34 papers organized under the following topical sections: Ceramic composites and functional materials; Ceramics, new alloys, and functional materials; and New alloys. Also included is a summary of a workshop on materials issues in low emission boilers and in high efficiency coal-fired cycles. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

  20. Material input of nuclear fuel

    International Nuclear Information System (INIS)

    Rissanen, S.; Tarjanne, R.

    2001-01-01

    The Material Input (MI) of nuclear fuel, expressed in terms of the total amount of natural material needed for manufacturing a product, is examined. The suitability of the MI method for assessing the environmental impacts of fuels is also discussed. Material input is expressed as a Material Input Coefficient (MIC), equalling to the total mass of natural material divided by the mass of the completed product. The material input coefficient is, however, only an intermediate result, which should not be used as such for the comparison of different fuels, because the energy contents of nuclear fuel is about 100 000-fold compared to the energy contents of fossil fuels. As a final result, the material input is expressed in proportion to the amount of generated electricity, which is called MIPS (Material Input Per Service unit). Material input is a simplified and commensurable indicator for the use of natural material, but because it does not take into account the harmfulness of materials or the way how the residual material is processed, it does not alone express the amount of environmental impacts. The examination of the mere amount does not differentiate between for example coal, natural gas or waste rock containing usually just sand. Natural gas is, however, substantially more harmful for the ecosystem than sand. Therefore, other methods should also be used to consider the environmental load of a product. The material input coefficient of nuclear fuel is calculated using data from different types of mines. The calculations are made among other things by using the data of an open pit mine (Key Lake, Canada), an underground mine (McArthur River, Canada) and a by-product mine (Olympic Dam, Australia). Furthermore, the coefficient is calculated for nuclear fuel corresponding to the nuclear fuel supply of Teollisuuden Voima (TVO) company in 2001. Because there is some uncertainty in the initial data, the inaccuracy of the final results can be even 20-50 per cent. The value

  1. Integrating the stabilization of nuclear materials

    Energy Technology Data Exchange (ETDEWEB)

    Dalton, H.F. [Department of Energy, Washington, DC (United States)

    1996-05-01

    In response to Recommendation 94-1 of the Defense Nuclear Facilities Safety Board, the Department of Energy committed to stabilizing specific nuclear materials within 3 and 8 years. These efforts are underway. The Department has already repackaged the plutonium at Rocky Flats and metal turnings at Savannah River that had been in contact with plastic. As this effort proceeds, we begin to look at activities beyond stabilization and prepare for the final disposition of these materials. To describe the plutonium materials being stabilize, Figure 1 illustrates the quantities of plutonium in various forms that will be stabilized. Plutonium as metal comprises 8.5 metric tons. Plutonium oxide contains 5.5 metric tons of plutonium. Plutonium residues and solutions, together, contain 7 metric tons of plutonium. Figure 2 shows the quantity of plutonium-bearing material in these four categories. In this depiction, 200 metric tons of plutonium residues and 400 metric tons of solutions containing plutonium constitute most of the material in the stabilization program. So, it is not surprising that much of the work in stabilization is directed toward the residues and solutions, even though they contain less of the plutonium.

  2. Powder metallurgical high performance materials. Proceedings. Volume 3: general topics

    International Nuclear Information System (INIS)

    Kneringer, G.; Roedhammer, P.; Wildner, H.

    2001-01-01

    The proceedings of these seminars form an impressive chronicle of the continued progress in the understanding of refractory metals and cemented carbides and in their manufacture and application. The 15 th Plansee Seminar was convened under the general theme 'Powder Metallurgy High Performance Materials'. Under this broadened perspective the seminar will strive to look beyond the refractory metals and cemented carbides, which remain at its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. (boteke)

  3. Proceedings of the 2. SIPEN: Integration week from IPEN - Brazilian Institute for Energy and Nuclear Researches, CNEN/SP

    International Nuclear Information System (INIS)

    1994-01-01

    The technical-scientific activities of IPEN (Instituto de Pesquisas Energeticas e Nucleares), Brazilian CNEN, has been presented in these proceedings. It includes the following topics: management and logistics, infra-structure and support, application of nuclear techniques, fuel cycle, materials, reactor research, development of products and services, radiation protection and monitoring. Nuclear medicine and application of radiation in biological assays are studied. Environmental impacts and management of radioactive wastes are also presented

  4. Nuclear fuel cladding material

    International Nuclear Information System (INIS)

    Nakahigashi, Shigeo.

    1982-01-01

    Purpose: To largely improve the durability and the safety of fuel cladding material. Constitution: Diffusion preventive layers, e.g., aluminum or the like are covered on both sides of a zirconium alloy base layer of thin material, and corrosion resistant layers, e.g., copper or the like are covered thereon. This thin plate material is intimately wound in a circularly tubular shape in a plurality of layers to form a fuel cladding tube. With such construction, corrosion of the tube due to fuel and impurity can be prevented by the corrosion resistant layers, and the diffusion of the corrosion resistant material to the zirconium alloy can be prevented by the diffusion preventive layers. Since a plurality of layers are cladded, even if the corrosion resistant layers are damaged or cracked due to stress corrosion, only one layer is damaged or cracked, but the other layers are not affected. (Sekiya, K.)

  5. Proceedings of the 2000 symposium on nuclear data

    Energy Technology Data Exchange (ETDEWEB)

    Yamano, Naoki [Sumitomo Atomic Energy Industries, Ltd., Tokyo (Japan); Fukahori, Tokio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-03-01

    The 2000 Symposium on Nuclear Data was held at Tokai Research Establishment, Japan Atomic Energy Research Institute (JAERI), on 16th and 17th of November 2000. Japanese Nuclear Data Committee and Nuclear Data Center, JAERI organized this symposium. In the oral sessions, presented were 18 papers on topics of recent experiments, status of JENDL-3.3 and JENDL High Energy File, benchmark tests of JENDL-3.2, international activities and other subjects. In the poster session, presented were 40 papers concerning experiments, evaluations, benchmark tests and on-line database on nuclear data. Those presented papers are compiled in the proceedings. The 58 of the presented papers are indexed individually. (J.P.N.)

  6. Nuclear and Renewable Energy Synergies Workshop: Report of Proceedings

    International Nuclear Information System (INIS)

    Ruth, M.; Antkowiak, M.; Gossett, S.

    2011-01-01

    Two of the major challenges the U.S. energy sector faces are greenhouse gas emissions and oil that is both imported and potentially reaching a peak (the point at which maximum extraction is reached). Interest in development of both renewable and nuclear energy has been strong because both have potential for overcoming these challenges. Research in both energy sources is ongoing, but relatively little research has focused on the potential benefits of combining nuclear and renewable energy. In September 2011, the Joint Institute for Strategic Energy Analysis (JISEA) convened the Nuclear and Renewable Energy Synergies Workshop at the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) to identify potential synergies and strategic leveraging opportunities between nuclear energy and renewable energy. Industry, government, and academic thought leaders gathered to identify potential broad categories of synergies and brainstorm topic areas for additional analysis and research and development (R and D). This report records the proceedings and outcomes of the workshop.

  7. Seismic evaluation of existing nuclear facilities. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    Programmes for re-evaluation and upgrading of safety of existing nuclear facilities are presently under way in a number of countries around the world. An important component of these programmes is the re-evaluation of the seismic safety through definition of new seismic parameters at the site and evaluation of seismic capacity of structures, equipment and distribution systems following updated information and criteria. The Seminar is intended to provide a forum for the exchange of information and discussion of the state-of-the-art on seismic safety of nuclear facilities in operation or under construction. Both analytical and experimental techniques for the evaluation of seismic capacity of structures, equipment and distribution systems are discussed. Full scale and field tests of structures and components using shaking tables, mechanical exciters, explosive and shock tests, and ambient vibrations are included in the seminar programme with emphasis on recent case histories. Presentations at the Seminar also include analytical techniques for the determination of dynamic properties of soil-structure systems from experiments as well as calibration of numerical models. Methods and criteria for seismic margin assessment based on experience data obtained from the behaviour of structures and components in real earthquakes are discussed. Guidelines for defining technical requirements for capacity re-evaluation (i.e. acceptable behaviour limits and design and implementation of structure and components upgrades are also presented and discussed. The following topics were covered during 7 sessions: earthquake experience and seismic re-evaluation; country experience in seismic re-evaluation programme; generic WWER studies; analytical methods for seismic capacity re-evaluation; experimental methods for seismic capacity re-evaluation; case studies.

  8. Seismic evaluation of existing nuclear facilities. Proceedings

    International Nuclear Information System (INIS)

    1995-01-01

    Programmes for re-evaluation and upgrading of safety of existing nuclear facilities are presently under way in a number of countries around the world. An important component of these programmes is the re-evaluation of the seismic safety through definition of new seismic parameters at the site and evaluation of seismic capacity of structures, equipment and distribution systems following updated information and criteria. The Seminar is intended to provide a forum for the exchange of information and discussion of the state-of-the-art on seismic safety of nuclear facilities in operation or under construction. Both analytical and experimental techniques for the evaluation of seismic capacity of structures, equipment and distribution systems are discussed. Full scale and field tests of structures and components using shaking tables, mechanical exciters, explosive and shock tests, and ambient vibrations are included in the seminar programme with emphasis on recent case histories. Presentations at the Seminar also include analytical techniques for the determination of dynamic properties of soil-structure systems from experiments as well as calibration of numerical models. Methods and criteria for seismic margin assessment based on experience data obtained from the behaviour of structures and components in real earthquakes are discussed. Guidelines for defining technical requirements for capacity re-evaluation (i.e. acceptable behaviour limits and design and implementation of structure and components upgrades are also presented and discussed. The following topics were covered during 7 sessions: earthquake experience and seismic re-evaluation; country experience in seismic re-evaluation programme; generic WWER studies; analytical methods for seismic capacity re-evaluation; experimental methods for seismic capacity re-evaluation; case studies

  9. Transport of nuclear materials

    International Nuclear Information System (INIS)

    Anon.

    2002-01-01

    During november and december 2001, 2 events concerning nuclear transport were reported and classified on the first grade (grade 1) of the INES scale. The first event concerns a hole in a transport cask of contaminated tools. The hole seems to have been made by the fork of a handling equipment. The second event concerns the loss of a parcel containing a technetium generator, this generator represented an activity of about 141 G Becquerel of 99 Mo the day it left the premises of CIS-bio in Saclay. (A.C.)

  10. Proceedings of the third meeting on nuclear analysis

    International Nuclear Information System (INIS)

    1984-04-01

    This international meeting presents a series of methodical and device developments in the field of nuclear analysis techniques such as nuclear reaction analysis, activation analysis, pixe analysis, tracer techniques or atom and nuclear spectroscopy. The applications cover an extensive field in energetics, geology, medicine, biology, environment protection, materials science etc. and are presented in 141 papers

  11. Nuclear technology and materials science

    International Nuclear Information System (INIS)

    Olander, D.R.

    1992-01-01

    Current and expected problems in the materials of nuclear technology are reviewed. In the fuel elements of LWRs, cladding waterside corrosion, secondary hydriding and pellet-cladding interaction may be significant impediments to extended burnup. In the fuel, fission gas release remains a key issue. Materials issues in the structural alloys of the primary system include stress-corrosion cracking of steel, corrosion of steam generator tubing and pressurized thermal shock of the reactor vessel. Prediction of core behavior in severe accidents requires basic data and models for fuel liquefaction, aerosol formation, fission product transport and core-concrete interaction. Materials questions in nuclear waste management and fusion technology are briefly reviewed. (author)

  12. Introduction to nuclear material safeguards

    International Nuclear Information System (INIS)

    Kuroi, Hideo

    1986-01-01

    This article is aimed at outlining the nuclear material safeguards. The International Atomic Energy Agency (IAEA) was established in 1957 and safeguards inspection was started in 1962. It is stressed that any damage resulting from nuclear proliferation would be triggered by a human intentional act. Various measures have been taken by international societies and nations, of which the safeguards are the only means which relay mainly on technical procedures. There are two modes of diversing nuclear materials to military purposes. One would be done by national intension while the other by indivisulas or expert groups, i.e., sub-national intention. IAEA is responsible for the prevention of diversification by nations, for which the international safeguards are being used. Measures against the latter mode of diversification are called nuclear protection, for which each nation is responsible. The aim of the safeguards under the Nonproliferation Treaty is to detect the diversification of a significant amount of nuclear materials from non-military purposes to production of nuclear explosion devices such as atomic weapons or to unidentified uses. Major technical methods used for the safeguards include various destructive and non-destructive tests as well as containment and monitoring techniques. System techniques are to be employed for automatic containment and monitoring procedures. Appropriate nuclear protection system techniques should also be developed. (Nogami, K.)

  13. Physical protection of nuclear material

    International Nuclear Information System (INIS)

    1975-01-01

    Full text: An Advisory Group met to consider the up-dating and extension of the Recommendations for the Physical Protection of Nuclear Material, produced in 1972. Twenty-seven experts from 11 countries and EURATOM were present. Growing concern has been expressed in many countries that nuclear material may one day be used for acts of sabotage or terrorism. Serious attention is therefore being given to the need for States to develop national systems for the physical protection of nuclear materials during use, storage and transport throughout the nuclear fuel cycle which should minimize risks of sabotage or theft. The revised Recommendations formulated by the Advisory Group include new definitions of the objectives of national systems of physical protection and proposals for minimizing possibilities of unauthorized removal and sabotage to nuclear facilities. The Recommendations also describe administrative or organizational steps to be taken for this purpose and the essential technical requirements of physical protection for various types and locations of nuclear material, e.g., the setting up of protected areas, the use of physical barriers and alarms, the need for security survey, and the need of advance arrangements between the States concerned in case of international transportation, among others. (author)

  14. International workshop on advanced materials for high precision detectors. Proceedings

    International Nuclear Information System (INIS)

    Nicquevert, B.; Hauviller, C.

    1994-01-01

    These proceedings gather together the contributions to the Workshop on Advanced Materials for High Precision Detectors, which was held from 28-30 September 1994 in Archamps, Haute-Savoie, France. This meeting brought together international experts (researchers, physicists and engineers) in the field of advanced materials and their use in high energy physics detectors or spacecraft applications. Its purpose was to discuss the status of the different materials currently in use in the structures of detectors and spacecraft, together with their actual performances, technological implications and future prospects. Environmental effects, such as those of moisture and radiation, were discussed, as were design and manufacturing technologies. Some case studies were presented. (orig.)

  15. Physics and technology of nuclear materials

    CERN Document Server

    Ursu, Ioan

    2015-01-01

    Physics and Technology of Nuclear Materials presents basic information regarding the structure, properties, processing methods, and response to irradiation of the key materials that fission and fusion nuclear reactors have to rely upon. Organized into 12 chapters, this book begins with selectively several fundamentals of nuclear physics. Subsequent chapters focus on the nuclear materials science; nuclear fuel; structural materials; moderator materials employed to """"slow down"""" fission neutrons; and neutron highly absorbent materials that serve in reactor's power control. Other chapters exp

  16. Nuclear material shipment study

    International Nuclear Information System (INIS)

    Shepherd, E.W.

    1980-01-01

    The Radioactive Material Transport Assessment Study is expected to provide a flexible set of capabilities and useful information to the public, industry and government users by using a system design to assure obtaining high quality data from selected industry sources at acceptable cost. It is expected that the shipping record approach coupled with an efficient sampling strategy will accomplish this. The study is also designed to yield analytical capabilities and statistical output to serve public, industry and government users. The information provided by the study will make a valuable contribution to environmental and accident risk assessment, policy development and operational planning and management activities

  17. Proceedings of 2nd Korea-China Congress of Nuclear Medicine and the Korean Society Nuclear Medicine Spring Meeting 2000

    International Nuclear Information System (INIS)

    2000-01-01

    This proceedings contains articles of 2nd Korea-China Congress of Nuclear Medicine and 2000 spring meeting of the Korean Society Nuclear Medicine. It was held on May 17-19, 2000 in Seoul, Korean. This proceedings is comprised of 6 sessions. The subject titles of session are as follows: general nuclear medicine, neurology, oncology, radiopharmacy and biology, nuclear cardiology, nuclear cardiology: physics and instrumentation and so on. (Yi, J. H.)

  18. The century of nuclear materials

    Science.gov (United States)

    Mansur, Lou; Was, Gary S.; Zinkle, Steve; Petti, David; Ukai, Shigeharu

    2018-03-01

    In the spring of 1959 the well-read metallurgist would have noticed the first issue of an infant Journal, one dedicated to a unique and fast growing field of materials issues associated with nuclear energy systems. The periodical, Journal of Nuclear Materials (JNM), is now the leading publication in the field from which it takes its name, thriving beyond the rosiest expectations of its founders. The discipline is well into the second half-century. During that time much has been achieved in nuclear materials; the Journal provides the authoritative record of virtually all those accomplishments. These pages introduce the 500th volume, a significant measure in the world of publishing. The Editors reflect on the progress in the field and the role of this journal.

  19. LECI Department of Nuclear Materials

    International Nuclear Information System (INIS)

    2006-01-01

    The LECI is a 'hot' laboratory dedicated mostly to the characterization of irradiated materials. It has, however, limited activities on fuel, as a back up to the LECA STAR in Cadarache. The LECI belongs to the Section of Research on Irradiated Materials (Department of Nuclear Materials). The Department for Nuclear Materials (DMN) has for its missions: - to contribute, through theoretical and experimental investigations, to the development of knowledge in materials science in order to be able to predict the evolution of the material physical and mechanical properties under service conditions (irradiation, thermomechanical solicitations, influence of the environment,..); - to characterize the properties of the materials used in the nuclear industry in order to determine their performance and to be able to predict their life expectancy, in particular via modelling. These materials can be irradiated or not, and originate from surveillance programs, experimental neutron irradiations or simulated irradiations with charged particles; - to establish, maintain and make use of the databases generated by these data; - to propose new or optimized materials, satisfying future service conditions and extend the life or the competitiveness of the associated systems; - to establish constitutive laws and models for the materials in service, incidental, accidental and storage conditions, and contribute to the development of the associated design codes in order to support the safety argumentation of utilities and vendors; - to provide expertise on industrial components, in particular to investigate strain or rupture mechanisms and to offer leads for improvement. This document presents, first, the purpose of the LECI (Historical data, Strategy, I and K shielded cell lines (building 605), M shielded cell line (building 625), Authorized materials). Then, it presents the microscopy and irradiation damage studies laboratory of the Saclay centre (Building 605) Which belongs to the Nuclear

  20. 16th DOE nuclear air cleaning conference: proceedings

    International Nuclear Information System (INIS)

    First, M.W.

    1981-02-01

    Major topics discussed during the Sixteenth DOE Nuclear Air Cleaning Conference were: waste treatment, including volume reduction and storage; system and component response to stress and accident conditions; Three Mile Island accident; iodine adsorption; treatment and storage of noble gas: treatment of offgases from chemical processing; aerosol; behavior; containment venting; laboratory and in-place filter-testing methods; and particulate filtration. Volume I of the Proceedings has 49 papers from the following sessions; HEPA filter test methods; noble gas separation; air cleaning system design; containment venting; iodine adsorption; reprocessing offgas cleaning; critical review; filtration; filter testing; and aerosols. Volume II contains 44 papers from the sessions on: nuclear waste treatment; critical review; noble gas treatment; carbon-14 and tritium; air cleaning system response to stress; nuclear standards and safety; round table; open end; and air cleaning technology at Three Mile Island. Abstracts are provided for all of these papers

  1. 16th DOE nuclear air cleaning conference: proceedings

    International Nuclear Information System (INIS)

    First, M.W.

    1981-02-01

    Major topics discussed during the Sixteenth DOE Nuclear Air Cleaning Conference were: waste treatment, including volume reduction and storage; system and component response to stress and accident conditions; Three Mile Island accident; iodine adsorption; treatment and storage of noble gas; treatment of offgases from chemical processing; aerosol behavior; containment venting; laboratory and in-place filter-testing methods; and particulate filtration. Volume I of the Proceedings has 49 papers from the following sessions: HEPA filter test methods; noble gas separation; air cleaning system design; containment venting; iodine adsorption; reprocessing offgas cleaning; critical review; filtration, filter testing, and aerosols. Volume II contains 44 papers from the sessions on: nuclear waste treatment; critical review; noble gas treatment; carbon-14 and tritium; air cleaning system response to stress; nuclear standards and safety; round table; open end; and air cleaning technology at Three Mile Island. Abstracts are provided for all of these papers

  2. Proceedings of the 2007 symposium on nuclear data

    International Nuclear Information System (INIS)

    Hazama, Taira; Fukahori, Tokio

    2008-11-01

    The 2007 Symposium on Nuclear Data was held at RICOTTI in Tokai-mura, Ibaraki-ken, Japan, on 29th and 30th of November 2007, with about 80 participants. Nuclear Data Division of Atomic Energy Society of Japan organized this symposium with cooperation of North Kanto Branch of the society. In the oral sessions, 10 papers were presented on topics of JEDNL-4, experiments, evaluations, applications, and research activity in China. In the poster session, presented were 12 papers concerning experiments, evaluations, benchmark tests, and so on. Tutorials on nuclear data, which were for cross section data creation process and PHITS code, were also done. Major part of those presented papers is compiled in this proceedings. The 19 of the presented papers are indexed individually. (J.P.N.)

  3. Nuclear data information system for nuclear materials

    International Nuclear Information System (INIS)

    Fujita, Mitsutane; Noda, Tetsuji; Utsumi, Misako

    1996-01-01

    The conceptual system for nuclear material design is considered and some trials on WWW server with functions of the easily accessible simulation of nuclear reactions are introduced. Moreover, as an example of the simulation on the system using nuclear data, transmutation calculation was made for candidate first wall materials such as 9Cr-2W steel, V-5Cr-5Ti and SiC in SUS316/Li 2 O/H 2 O(SUS), 9Cr-2W/Li 2 O/H 2 O(RAF), V alloy/Li/Be(V), and SiC/Li 2 ZrO 3 /He(SiC) blanket/shield systems based on ITER design model. Neutron spectrum varies with different blanket/shield compositions. The flux of low energy neutrons decreases in order of V< SiC< RAF< SUS blanket/shield systems. Fair amounts of W depletion in 9Cr-2W steel and the increase of Cr content in V-5Cr-5Ti were predicted in SUS or RAF systems. Concentration change in W and Cr is estimated to be suppressed if Li coolant is used in place of water. Helium and hydrogen production are not strongly affected by the different blanket/shield compositions. (author)

  4. Materials science for nuclear detection

    OpenAIRE

    Peurrung, Anthony

    2008-01-01

    The increasing importance of nuclear detection technology has led to a variety of research efforts that seek to accelerate the discovery and development of useful new radiation detection materials. These efforts aim to improve our understanding of how these materials perform, develop formalized discovery tools, and enable rapid and effective performance characterization. We provide an overview of these efforts along with an introduction to the history, physics, and taxonomy of radiation detec...

  5. Proceeding of the Fourth Scientific Presentation on Nuclear Fuel Cycle: Technology of Nuclear Fuel Cycle facing the Challenge of Energy Need on the 21-st Century

    International Nuclear Information System (INIS)

    Suripto, A.; Sajuti, D.; Aiman, S.; Yuwono, I.; Fathurrachman; Suwarno, H.; Suwardi; Amini, S.; Widjaksana

    1999-03-01

    The proceeding contains papers presented in the Fourth Scientific Presentation on Nuclear Fuel Element Cycle with theme of Technology of Nuclear Fuel Cycle facing the Challenge of Energy Need on the 21 s t Century, held on 1-2 December in Jakarta, Indonesia. These papers were divided by three groups that are technology of exploration, processing, purification and analysis of nuclear materials; technology of nuclear fuel elements and structures; and technology of waste management, safety and management of nuclear fuel cycle. There are 36 papers indexed individually. (ID)

  6. Nuclear Material (Offences) Act 1983

    International Nuclear Information System (INIS)

    1983-01-01

    The main purpose of this Act is to enable the United Kingdom to ratify the Convention on the Physical Protection of Nuclear Material which opened for signature at Vienne and New York on 3 March 1980. The Act extends throughout the United Kingdom. (NEA) [fr

  7. International control of nuclear materials

    International Nuclear Information System (INIS)

    Koponen, Hannu

    1989-01-01

    Nuclear materials are subject to both national and international safeguards control. The International Atomic Energy Agency (IAEA) takes care of the international safeguards control. The control activities, which are discussed in this article, are carried out according to the agreements between various countries and the IAEA

  8. Responsible stewardship of nuclear materials

    International Nuclear Information System (INIS)

    Hannum, W.H.

    1994-01-01

    The ability to tap the massive energy potential of nuclear fission was first developed as a weapon to end a terrible world war. Nuclear fission is also a virtually inexhaustible energy resource, and is the only energy supply in certain areas in Russia, Kazakhstan and elsewhere. The potential link between civilian and military applications has been and continues to be a source of concern. With the end of the Cold War, this issue has taken a dramatic turn. The U.S. and Russia have agreed to reduce their nuclear weapons stockpiles by as much as two-thirds. This will make some 100 tonnes of separated plutonium and 500 tonnes of highly enriched uranium available, in a form that is obviously directly usable for weapons. The total world inventory of plutonium is now around 1000 tonnes and is increasing at 60-70 tonnes per year. There is even more highly enriched uranium. Fortunately the correct answer to what to do with excess weapons material is also the most attractive. It should be used and reused as fuel for fast reactors. Material in use (particularly nuclear material) is very easy to monitor and control, and is quite unattractive for diversion. Active management of fissile materials not only makes a major contribution to economic stability and well-being, but also simplifies accountability, inspection and other safeguards processes; provides a revenue stream to pay for the necessary safeguards; and, most importantly, limits the prospective world inventory of plutonium to only that which is used and useful

  9. Nuclear and hazardous material perspective

    International Nuclear Information System (INIS)

    Sandquist, Gary M.; Kunze, Jay F.; Rogers, Vern C.

    2007-01-01

    The reemerging nuclear enterprise in the 21. century empowering the power industry and nuclear technology is still viewed with fear and concern by many of the public and many political leaders. Nuclear phobia is also exhibited by many nuclear professionals. The fears and concerns of these groups are complex and varied, but focus primarily on (1) management and disposal of radioactive waste [especially spent nuclear fuel and low level radioactive waste], (2) radiation exposures at any level, and (3) the threat nuclear terrorism. The root cause of all these concerns is the exaggerated risk perceived to human health from radiation exposure. These risks from radiation exposure are compounded by the universal threat of nuclear weapons and the disastrous consequences if these weapons or materials become available to terrorists or rogue nations. This paper addresses the bases and rationality for these fears and considers methods and options for mitigating these fears. Scientific evidence and actual data are provided. Radiation risks are compared to similar risks from common chemicals and familiar human activities that are routinely accepted. (authors)

  10. 9th Pacific Basin Nuclear Conference. Nuclear energy, science and technology - Pacific partnership. Proceedings Volume 2

    International Nuclear Information System (INIS)

    1994-04-01

    The theme of the 9th Pacific Basin Nuclear Conference held in Sydney from 1-6 May 1994, embraced the use of atom in energy production and in science and technology. The focus was on selected topics of current and on-going interest to countries around the Pacific Basin. The two-volume proceedings include both invited and contributed papers which have been indexed separately. This document, Volume 2 covers the following topics: education and training in Nuclear Science, public acceptance, nuclear safety and radiation protection, nuclear fuel resources and their utilisation, research reactors, cyclotrons and accelerators. refs., tabs., figs., ills

  11. Proceedings

    International Nuclear Information System (INIS)

    1974-01-01

    These 1974 Proceedings of the European Society of Nuclear Methods in Agriculture contain reports in the form of minutes of the meetings of various working groups of the Society, the programme and official addresses of the fifth annual meeting including annual reports of the chairman and the secretary of the Society, and the reports of each of the eleven working groups as well as the four following surveys entitled: 1) some aspects of research in plant breeding, conservation of genetic resources in connection with irradiation processes (by A. Jacques from FAO), 2) our responsibility for the environment (by D. Zeeuw from ITAL), 3) pilot plant for the irradiation of sewage sludge (by A. Suesz from Bayerische Landesanstalt fuer Bodenkultur und Pflanzenbau, Munich), 4) nuclear agronomy in France (by P. Guerin de Montgareuil from CEN, Cadarache). Summaries and provisional papers on presented topics will be published in ''ESNA Newsletter''

  12. Proceedings of the Eighth Conference of Nuclear Sciences and Applications

    International Nuclear Information System (INIS)

    2004-02-01

    The publication has been set up as a textbook for researching dealing with radioisotope production during work with Human needs of Nuclear Science and applications. The book consists of the following chapters: chemistry; radioisotope production, trace analysis; environment monitoring; environmental effect; waste management; physics; reactors; nuclear safety and safeguards; materials; radiation protection ; agriculture; hydrology; nuclear medicine; medical applications; radiation chemistry; environmental studies; biological effects of ionizing radiation on agriculture;

  13. Proceedings of the two day national workshop on advanced materials for engineering applications

    International Nuclear Information System (INIS)

    John Alexis, S.; Jayakumar, S.

    2012-01-01

    The subjects like material preparation, material forming, material properties, materials testing, material mechanics, material structure, metal materials, non-metallic materials, composite materials, medical materials, chemical materials, food materials, electrician/electrical materials, building materials, biological materials, electronic/magnetic/optical materials, advanced materials applications in engineering are included in the workshop. Processing of advanced materials, studies on novel ceramic coatings, high strength, light weight and nanostructured materials are discussed in this proceedings. Papers relevant to INIS are indexed separately

  14. Nuclear material statistical accountancy system

    International Nuclear Information System (INIS)

    Argentest, F.; Casilli, T.; Franklin, M.

    1979-01-01

    The statistical accountancy system developed at JRC Ispra is refered as 'NUMSAS', ie Nuclear Material Statistical Accountancy System. The principal feature of NUMSAS is that in addition to an ordinary material balance calcultation, NUMSAS can calculate an estimate of the standard deviation of the measurement error accumulated in the material balance calculation. The purpose of the report is to describe in detail, the statistical model on wich the standard deviation calculation is based; the computational formula which is used by NUMSAS in calculating the standard deviation and the information about nuclear material measurements and the plant measurement system which are required as data for NUMSAS. The material balance records require processing and interpretation before the material balance calculation is begun. The material balance calculation is the last of four phases of data processing undertaken by NUMSAS. Each of these phases is implemented by a different computer program. The activities which are carried out in each phase can be summarised as follows; the pre-processing phase; the selection and up-date phase; the transformation phase, and the computation phase

  15. Nuclear materials facility safety initiative

    International Nuclear Information System (INIS)

    Peddicord, K.L.; Nelson, P.; Roundhill, M.; Jardine, L.J.; Lazarev, L.; Moshkov, M.; Khromov, V.V.; Kruchkov, E.; Bolyatko, V.; Kazanskij, Yu.; Vorobeva, I.; Lash, T.R.; Newton, D.; Harris, B.

    2000-01-01

    Safety in any facility in the nuclear fuel cycle is a fundamental goal. However, it is recognized that, for example, should an accident occur in either the U.S. or Russia, the results could seriously delay joint activities to store and disposition weapons fissile materials in both countries. To address this, plans are underway jointly to develop a nuclear materials facility safety initiative. The focus of the initiative would be to share expertise which would lead in improvements in safety and safe practices in the nuclear fuel cycle.The program has two components. The first is a lab-to-lab initiative. The second involves university-to-university collaboration.The lab-to-lab and university-to-university programs will contribute to increased safety in facilities dealing with nuclear materials and related processes. These programs will support important bilateral initiatives, develop the next generation of scientists and engineers which will deal with these challenges, and foster the development of a safety culture

  16. Proceedings of the Second Regional Meeting on Nuclear Energy in Central Europe

    Energy Technology Data Exchange (ETDEWEB)

    Stritar, A; Jencic, I [eds.; Nuclear Society of Slovenia (Slovenia)

    1996-12-31

    Second Regional Meeting for Nuclear Energy in Central Europe is an annual meeting of the Nuclear Society of Slovenia. The proceedings contains 75 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region

  17. Proceedings of the Second Regional Meeting on Nuclear Energy in Central Europe

    International Nuclear Information System (INIS)

    Stritar, A.; Jencic, I.

    1995-01-01

    Second Regional Meeting for Nuclear Energy in Central Europe is an annual meeting of the Nuclear Society of Slovenia. The proceedings contains 75 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region

  18. Proceedings of the Twelfth Seminar on Computation in Nuclear Science and Technology

    International Nuclear Information System (INIS)

    Arbie, Bakri; Ardisasmita, Syamsa; Bunyamin, M.; Karsono, M.; Sangadji; Aziz, Ferhat; Marsodi; Su'ud, Zaki; Suhartanto, Heru

    2001-07-01

    The proceedings on Seminar Computation in Nuclear Science and Technologyis routine activity that held on Center for Development of Informatics and Computation Technology. The aims of proceeding is to be able to Exchange Information for interest in computation, Modelling and Simulation. The Seminar is attended by BATAN's on University Research in nuclear science activity. This proceedings used for another research. There are 26 papers which have separated index

  19. Materials of the Annual Scientific Conference at the Institute for Nuclear Research. (Collected reports)

    International Nuclear Information System (INIS)

    Vishnevs'kij, Yi.M.; Ostashko, V.V.

    1995-01-01

    The proceeding contain contributed papers submitted to the annual Scientific conference of the Institute for Nuclear Research, Ukraine (kiev, January 1996). The proceedings include reports have been presented on the following sections: Nuclear physics, Solid State physics, Plasma physics, Radio ecology, Reactor safety, Radiation and reactor materials Study. The book is a direct reproduction of the print-ready manuscripts presented by the authors. No corrections have been made in the texts

  20. Proceedings of the 6th Korea-China Joint workshop on nuclear waste management

    International Nuclear Information System (INIS)

    2005-11-01

    This proceedings contains articles of 6th Korea-China Joint workshop on nuclear waste management. It was held on November 16-17, 2005 in Kyeongju, Korea. This proceedings is comprised of 3 sessions. The main subject titles of session are as follows: Nuclear fuel cycle, Radioactive waste treatment, Radwaste disposal and decontamination and decommissioning. (Yi, J. H.)

  1. Physics and technology of nuclear materials

    International Nuclear Information System (INIS)

    Ursu, I.

    1985-01-01

    The subject is covered in chapters, entitled; elements of nuclear reactor physics; structure and properties of materials (including radiation effects); fuel materials (uranium, plutonium, thorium); structural materials (including - aluminium, zirconium, stainless steels, ferritic steels, magnesium alloys, neutron irradiation induced changes in the mechanical properties of structural materials); moderator materials (including - nuclear graphite, natural (light) water, heavy water, beryllium, metal hydrides); materials for reactor reactivity control; coolant materials; shielding materials; nuclear fuel elements; nuclear material recovery from irradiated fuel and recycling; quality control of nuclear materials; materials for fusion reactors (thermonuclear fusion reaction, physical processes in fusion reactors, fuel materials, materials for blanket and cooling system, structural materials, materials for magnetic devices, specific problems of material irradiation). (U.K.)

  2. Nuclear and Renewable Energy Synergies Workshop: Report of Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Ruth, M.; Antkowiak, M.; Gossett, S.

    2011-12-01

    Two of the major challenges the U.S. energy sector faces are greenhouse gas emissions and oil that is both imported and potentially reaching a peak (the point at which maximum extraction is reached). Interest in development of both renewable and nuclear energy has been strong because both have potential for overcoming these challenges. Research in both energy sources is ongoing, but relatively little research has focused on the potential benefits of combining nuclear and renewable energy. In September 2011, the Joint Institute for Strategic Energy Analysis (JISEA) convened the Nuclear and Renewable Energy Synergies Workshop at the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) to identify potential synergies and strategic leveraging opportunities between nuclear energy and renewable energy. Industry, government, and academic thought leaders gathered to identify potential broad categories of synergies and brainstorm topic areas for additional analysis and research and development (R&D). This report records the proceedings and outcomes of the workshop.

  3. Special nuclear material simulation device

    Science.gov (United States)

    Leckey, John H.; DeMint, Amy; Gooch, Jack; Hawk, Todd; Pickett, Chris A.; Blessinger, Chris; York, Robbie L.

    2014-08-12

    An apparatus for simulating special nuclear material is provided. The apparatus typically contains a small quantity of special nuclear material (SNM) in a configuration that simulates a much larger quantity of SNM. Generally the apparatus includes a spherical shell that is formed from an alloy containing a small quantity of highly enriched uranium. Also typically provided is a core of depleted uranium. A spacer, typically aluminum, may be used to separate the depleted uranium from the shell of uranium alloy. A cladding, typically made of titanium, is provided to seal the source. Methods are provided to simulate SNM for testing radiation monitoring portals. Typically the methods use at least one primary SNM spectral line and exclude at least one secondary SNM spectral line.

  4. 10 CFR 74.51 - Nuclear material control and accounting for strategic special nuclear material.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Nuclear material control and accounting for strategic special nuclear material. 74.51 Section 74.51 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) MATERIAL CONTROL AND ACCOUNTING OF SPECIAL NUCLEAR MATERIAL Formula Quantities of Strategic Special Nuclear...

  5. Analytical chemistry of nuclear materials

    International Nuclear Information System (INIS)

    1966-01-01

    The second panel on the Analytical Chemistry of Nuclear Materials was organized for two purposes: first, to advise the Seibersdorf Laboratory of the Agency on its future programme, and second, to review the results of the Second International Comparison of routine analysis of trace impurities in uranium and also the action taken as a result of the recommendations of the first panel in 1962. Refs, figs and tabs

  6. Nuclear reactors: physics and materials

    Energy Technology Data Exchange (ETDEWEB)

    Yadigaroglu, G

    2005-07-01

    In the form of a tutorial addressed to non-specialists, the article provides an introduction to nuclear reactor technology and more specifically to Light Water Reactors (LWR); it also shows where materials and chemistry problems are encountered in reactor technology. The basics of reactor physics are reviewed, as well as the various strategies in reactor design and the corresponding choices of materials (fuel, coolant, structural materials, etc.). A brief description of the various types of commercial power reactors follows. The design of LWRs is discussed in greater detail; the properties of light water as coolant and moderator are put in perspective. The physicochemical and metallurgical properties of the materials impose thermal limits that determine the performance and the maximum power a reactor can deliver. (author)

  7. 9th Pacific Basin Nuclear Conference. Nuclear energy, science and technology - Pacific partnership. Proceedings Volume 1

    International Nuclear Information System (INIS)

    1994-04-01

    The theme of the 9th Pacific Basin Nuclear conference held in Sydney from 1-6 May 1994, embraced the use of the atom in energy production and in science and technology. The focus was on selected topics of current and ongoing interest to countries around the Pacific Basin. The two-volume proceedings include both invited and contributed papers. They have been indexed separately. This document, Volume 1 covers the following topics: Pacific partnership; perspectives on nuclear energy, science and technology in Pacific Basin countries; nuclear energy and sustainable development; economics of the power reactors; new power reactor projects; power reactor technology; advanced reactors; radioisotope and radiation technology; biomedical applications

  8. Control of nuclear material specified equipment and specified material

    International Nuclear Information System (INIS)

    1982-04-01

    The goal and application field of NE 2.02 regulatory guide of CNEN (Comissao Nacional de Energia Nuclear), are described. This regulatory guide is about nuclear material management, specified equipment and specified material. (E.G.) [pt

  9. Criticality Control Fissile of Materials. Proceedings of the Symposium on Criticality Control of Fissile Materials

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1966-05-15

    Criticality control comprises all the administrative and technical procedures which enable the storage and processing of fissile material to be carried out under conditions of nuclear safety. It is of particular importance in the safe design and operation of chemical and metallurgical plants processing fissile material, in the handling and storage of enriched fuel for reactors, and in transportation of fissile material. The growth of nuclear power, with its increasing use of fissile material and production of plutonium, is leading to an ever widening need for this discipline. This Symposium was held 4 Vulgar-Fraction-One-Half years after the only other international meeting on this topic, at which the first broad exchange of ideas and theories enabled a comparison to be drawn between the various ways in which the subject is handled in the different countries. That meeting showed that criticality safety was often achieved by procedures known to be ultra-safe, as there was a great lack of useful experimental data with which to check theoretical models. Since that time the quantities of material being processed have increased, and with the now urgent necessity of achieving economic, and hence commercially competitive, operation, the procedure of using arbitrary factors of safety is no longer adequate. Plant Managers now require good data on the basis of which they can choose a suitable factor of safety, and design a process to be safe under any foreseeable circumstances. The present Symposium showed the great increase in the amount of available experimental data and its importance in checking the now highly sophisticated computer calculations. There are many diagrams in these Proceedings with curves from which critical parameters for various configurations can be taken. The dearth of data for plutonium systems is causing some difficulty in plutonium processing plants, which are becoming commercially important. The excellent safety record of the atomic energy industry

  10. Better materials for nuclear energy

    International Nuclear Information System (INIS)

    Banerjee, S.

    2005-01-01

    The improved performance of present generation nuclear reactors and the realization of advanced reactor concepts, both, require development of better materials. Physical metallurgy /materials science principles which have been exploited in meeting the exacting requirements of nuclear systems comprising fuels, structural materials, moderators and coolants are outlined citing a few specific examples. While the incentive for improvement of traditional fuels (e.g., UO 2 fuel) is primarily for increasing the average core burn up, the development of advanced fuels (e.g., MOX, mixed carbide, nitride, silicide and dispersion fuels) are directed towards better utilization of fissile and fertile inventories through adaptation of innovative fuel cycles. As the burn up of UO 2 fuel reaches higher levels, a more detailed and quantitative understanding of the phenomena such as fission gas release, fuel restructuring - induced by radiation and thermal gradients and pellet-clad interaction is being achieved. Development of zirconium based alloys for both cladding and pressure tube applications is discussed with reference to their physical metallurgy, fabrication techniques, in-reactor degradation mechanisms, and in-service inspection. The issue of radiation embrittlement of reactor pressure vessels (RPVs) is covered drawing a comparison between the western and eastern specifications of RPV steels. The search for new materials which can stand higher rates of atomic displacement due to radiation has led to the development of swelling resistant austenitic and ferritic stainless steels for fast reactor applications as exemplified by the development of the D-9 steel for Indian fast breeder reactor. New challenges are thrown to material scientists for the development of materials suitable for high temperature reactors, which have a potential for providing primary heat for thermo chemical dissociation of water. Development of several ceramic materials, carbon based materials, dissimilar

  11. Control of Nuclear Materials and Special Equipment (Nuclear Safety Regulations)

    International Nuclear Information System (INIS)

    Cizmek, A.; Prah, M.; Medakovic, S.; Ilijas, B.

    2008-01-01

    Based on Nuclear Safety Act (OG 173/03) the State Office for Nuclear Safety (SONS) in 2008 adopted beside Ordinance on performing nuclear activities (OG 74/06) and Ordinance on special conditions for individual activities to be performed by expert organizations which perform activities in the area of nuclear safety (OG 74/06) the new Ordinance on the control of nuclear material and special equipment (OG 15/08). Ordinance on the control of nuclear material and special equipment lays down the list of nuclear materials and special equipment as well as of nuclear activities covered by the system of control of production of special equipment and non-nuclear material, the procedure for notifying the intention to and filing the application for a license to carry out nuclear activities, and the format and contents of the forms for doing so. This Ordinance also lays down the manner in which nuclear material records have to be kept, the procedure for notifying the State administration organization (regulatory body) responsible for nuclear safety by the nuclear material user, and the keeping of registers of nuclear activities, nuclear material and special equipment by the State administration organization (regulatory body) responsible for nuclear safety, as well as the form and content of official nuclear safety inspector identification card and badge.(author)

  12. Proceeding of the Fifth Scientific Presentation on Nuclear Fuel Cycle: Development of Nuclear Fuel Cycle Technology in Third Millennium; Presentasi Ilmiah Daur Bahan Bakar Nuklir V: Pengembangan Teknologi Daur Bahan Bakar Nuklir Dalam Menyongsong Milenium Ketiga

    Energy Technology Data Exchange (ETDEWEB)

    Suripto, A; Sastratenaya, A S; Sutarno, D [National Atomic Energy Agency, Serpong (Indonesia); and others

    2000-03-08

    The proceeding contains papers presented in the Fifth Scientific Presentation on Nuclear Fuel Element Cycle with theme of Development of Nuclear Fuel Cycle Technology in Third Millennium, held on 22 February in Jakarta, Indonesia. These papers were divided by three groups that are technology of exploration, processing, purification and analysis of nuclear materials; technology of nuclear fuel elements and structures; and technology of waste management, safety and management of nuclear fuel cycle. There are 35 papers indexed individually. (id)

  13. Proceedings of the nuclear criticality technology safety project

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez, R.G. [comp.

    1997-06-01

    This document contains summaries of the most of the papers presented at the 1994 Nuclear Criticality Technology Safety Project (NCTSP) meeting, which was held May 10 and 11 at Williamsburg, Va. The meeting was broken up into seven sessions, which covered the following topics: (1) Validation and Application of Calculations; (2) Relevant Experiments for Criticality Safety; (3) Experimental Facilities and Capabilities; (4) Rad-Waste and Weapons Disassembly; (5) Criticality Safety Software and Development; (6) Criticality Safety Studies at Universities; and (7) Training. The minutes and list of participants of the Critical Experiment Needs Identification Workgroup meeting, which was held on May 9 at the same venue, has been included as an appendix. A second appendix contains the names and addresses of all NCTSP meeting participants. Separate abstracts have been indexed to the database for contributions to this proceedings.

  14. Symposium on engineering with nuclear explosives. Proceedings. Volume 2

    International Nuclear Information System (INIS)

    1970-05-01

    This symposium on 'Engineering with Nuclear Explosives' reports to the Plowshare community, both national and international, the progress achieved since April 1964, the date of the Third Plowshare Symposium. In structuring the technical presentations, contributions of broadest interest were placed at the beginning, thus forming a common base of current information and applied science understanding developed in support of Plowshare technology. Sessions of speciality or pertaining to specific areas of application and engineering follow logically in the program. The Plenary Session reviewed the current status of the Plowshare Program from the technical, government, and industrial points of view. The 112 papers presented at 15 technical sessions covered all technical aspects of the Plowshare Program. The conference summary reviewed principal themes, areas of significant advance, and subjects requiring further attention that emerged during the technical conference. This proceedings is the record of the symposium

  15. Symposium on engineering with nuclear explosives. Proceedings. Vol. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1970-05-01

    This symposium on 'Engineering with Nuclear Explosives' reports to the Plowshare community, both national and international, the progress achieved since April 1964, the date of the Third Plowshare Symposium. In structuring the technical presentations, contributions of broadest interest were placed at the beginning, thus forming a common base of current information and applied science understanding developed in support of Plowshare technology. Sessions of speciality or pertaining to specific areas of application and engineering follow logically in the program. The Plenary Session reviewed the current status of the Plowshare Program from the technical, government, and industrial points of view. The 112 papers presented at 15 technical sessions covered all technical aspects of the Plowshare Program. The conference summary reviewed principal themes, areas of significant advance, and subjects requiring further attention that emerged during the technical conference. These proceedings are the record of the symposium.

  16. Symposium on engineering with nuclear explosives. Proceedings. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1970-05-15

    This symposium on 'Engineering with Nuclear Explosives' reports to the Plowshare community, both national and international, the progress achieved since April 1964, the date of the Third Plowshare Symposium. In structuring the technical presentations, contributions of broadest interest were placed at the beginning, thus forming a common base of current information and applied science understanding developed in support of Plowshare technology. Sessions of speciality or pertaining to specific areas of application and engineering follow logically in the program. The Plenary Session reviewed the current status of the Plowshare Program from the technical, government, and industrial points of view. The 112 papers presented at 15 technical sessions covered all technical aspects of the Plowshare Program. The conference summary reviewed principal themes, areas of significant advance, and subjects requiring further attention that emerged during the technical conference. This proceedings is the record of the symposium.

  17. Proceedings of the nuclear criticality technology safety project

    International Nuclear Information System (INIS)

    Sanchez, R.G.

    1997-06-01

    This document contains summaries of the most of the papers presented at the 1994 Nuclear Criticality Technology Safety Project (NCTSP) meeting, which was held May 10 and 11 at Williamsburg, Va. The meeting was broken up into seven sessions, which covered the following topics: (1) Validation and Application of Calculations; (2) Relevant Experiments for Criticality Safety; (3) Experimental Facilities and Capabilities; (4) Rad-Waste and Weapons Disassembly; (5) Criticality Safety Software and Development; (6) Criticality Safety Studies at Universities; and (7) Training. The minutes and list of participants of the Critical Experiment Needs Identification Workgroup meeting, which was held on May 9 at the same venue, has been included as an appendix. A second appendix contains the names and addresses of all NCTSP meeting participants. Separate abstracts have been indexed to the database for contributions to this proceedings

  18. Symposium on engineering with nuclear explosives. Proceedings. Vol. 1

    International Nuclear Information System (INIS)

    1970-05-01

    This symposium on 'Engineering with Nuclear Explosives' reports to the Plowshare community, both national and international, the progress achieved since April 1964, the date of the Third Plowshare Symposium. In structuring the technical presentations, contributions of broadest interest were placed at the beginning, thus forming a common base of current information and applied science understanding developed in support of Plowshare technology. Sessions of speciality or pertaining to specific areas of application and engineering follow logically in the program. The Plenary Session reviewed the current status of the Plowshare Program from the technical, government, and industrial points of view. The 112 papers presented at 15 technical sessions covered all technical aspects of the Plowshare Program. The conference summary reviewed principal themes, areas of significant advance, and subjects requiring further attention that emerged during the technical conference. These proceedings are the record of the symposium

  19. Analytical chemistry of nuclear materials

    International Nuclear Information System (INIS)

    1963-01-01

    The last two decades have witnessed an enormous development in chemical analysis. The rapid progress of nuclear energy, of solid-state physics and of other fields of modern industry has extended the concept of purity to limits previously unthought of, and to reach the new dimensions of these extreme demands, entirely new techniques have been invented and applied and old ones have been refined. Recognizing these facts, the International Atomic Energy Agency convened a Panel on Analytical Chemistry of Nuclear Materials to discuss the general problems facing the analytical chemist engaged in nuclear energy development, particularly in newly developing centre and countries, to analyse the represent situation and to advise as to the directions in which research and development appear to be most necessary. The Panel also discussed the analytical programme of the Agency's laboratory at Seibersdorf, where the Agency has already started a programme of international comparison of analytical methods which may lead to the establishment of international standards for many materials of interest. Refs and tabs

  20. Nuclear materials for fission reactors

    International Nuclear Information System (INIS)

    Matzke, H.; Schumacher, G.

    1992-01-01

    This volume brings together 47 papers from scientists involved in the fabrication of new nuclear fuels, in basic research of nuclear materials, their application and technology as well as in computer codes and modelling of fuel behaviour. The main emphasis is on progress in the development of non -oxide fuels besides reporting advances in the more conventional oxide fuels. The two currently performed large reactor safety programmes CORA and PHEBUS-FP are described in invited lectures. The contributions review basic property measurements, as well as the present state of fuel performance modelling. The performance of today's nuclear fuel, hence UO 2 , at high burnup is also reviewed with particular emphasis on the recently observed phenomenon of grain subdivision in the cold part of the oxide fuel at high burnup, the so-called 'rim' effect. Similar phenomena can be simulated by ion implantation in order to better elucidate the underlying mechanism and reviews on high resolution electron microscopy provide further information. The papers will provide a useful treatise of views, ideas and new results for all those scientists and engineers involved in the specific questions of current nuclear waste management

  1. Selection of nuclear reactor coolant materials

    International Nuclear Information System (INIS)

    Shi Lisheng; Wang Bairong

    2012-01-01

    Nuclear material is nuclear material or materials used in nuclear industry, the general term, it is the material basis for the construction of nuclear power, but also a leader in nuclear energy development, the two interdependent and mutually reinforcing. At the same time, nuclear materials research, development and application of the depth and breadth of science and technology reflects a nation and the level of the nuclear power industry. Coolant also known as heat-carrier agent, is an important part of the heart nuclear reactor, its role is to secure as much as possible to the economic output in the form fission energy to heat the reactor to be used: the same time cooling the core, is controlled by the various structural components allowable temperature. This paper described the definition of nuclear reactor coolant and characteristics, and then addressed the requirements of the coolant material, and finally were introduced several useful properties of the coolant and chemical control. (authors)

  2. Proceeding of the seventh Nuclear and Particle Physics Conference (NUPPAC-2009)

    International Nuclear Information System (INIS)

    Comsan, M.N.H.

    2009-11-01

    The publication has been set up as proceedings of the Nuclear and Particle physics conference. the conference consists Nuclear Scattering and Reactions; High Energy Physics; Nuclear Structure and Spectroscopy; Neutron and Reactor Physics; Relativistic and Quantum Physics; Modeling, Codes and Simulation; Nuclear Analytical Techniques; Accelerator and Reactor Utilization; Detectors and Instrumentation; Radiation and Radioactivity. This conference consists of 662 p., figs., tabs., refs.

  3. Proceeding of the Sixth Nuclear and Particle Physics Conference (NUPPAC-2007)

    International Nuclear Information System (INIS)

    2008-11-01

    The publication has been set up as proceedings of the Nuclear and Particle Physics conference, the conference contains of the following subjects: High Energy Physics; Nuclear Scattering and Reactions; Nuclear Structure and Spectroscopy; Nuclear and Reactor Physics; Relativistic and Quantum Physics; Plasma and magneto hydro Dynamics; Computation and Simulation and Radiation Measurement and Dosimetry. This conference consists of 642 pages., figs., tabs., refs

  4. Proceedings of the 9. National Seminar on Technology and Safety of Nuclear Power Plants and Nuclear Facilities

    International Nuclear Information System (INIS)

    Antariksawan, Anhar R.; Soetrisnanto, Arnold Y; Aziz, Ferhat; Untoro, Pudji; Su'ud, Zaki; Zarkasi, Amin Santoso; Lasman, As Natio

    2003-08-01

    The ninth proceedings of seminar safety and technology of nuclear power plant and nuclear facilities held by National Nuclear Energy Agency and PLN-JTK. The aims of seminar is to exchange and disseminate information about Safety and Nuclear Power Plant Technology and Nuclear Facilities consist of Technology High Temperature Reactor and Application for National Development Sustainable and High Technology. This seminar cover all aspects Technology, Power Reactor, Research Reactor High Temperature Reactor and Nuclear Facilities. There are 20 articles have separated index

  5. Properties of structural materials in liquid metal environment. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Borgstedt, H U [ed.

    1991-12-15

    The International Working Group on Fast Reactors (IWGFR) Specialists Meeting on Properties of Structural Materials in Liquid Metal Environment was held during June 18 to June 20, 1991, at the Nuclear Research Centre (Kernforschungszentrum) in Karlsruhe, Germany. The Specialists Meeting was divided into five technical sessions which addressed topics as follows: Creep-Rupture Behaviour of Structural Materials in Liquid Metal Environment; Behaviour of Materials in Liquid Metal Environments under Off-Normal Conditions;Fatigue and Creep-Fatigue of Structural Materials in Liquid Metal Environment; Crack Propagation in Liquid Sodium; and Conclusions and recommendations. Individual papers have been cataloged separately.

  6. Fieldable Nuclear Material Identification System

    International Nuclear Information System (INIS)

    Radle, James E.; Archer, Daniel E.; Carter, Robert J.; Mullens, James Allen; Mihalczo, John T.; Britton, Charles L. Jr.; Lind, Randall F.; Wright, Michael C.

    2010-01-01

    The Fieldable Nuclear Material Identification System (FNMIS), funded by the NA-241 Office of Dismantlement and Transparency, provides information to determine the material attributes and identity of heavily shielded nuclear objects. This information will provide future treaty participants with verifiable information required by the treaty regime. The neutron interrogation technology uses a combination of information from induced fission neutron radiation and transmitted neutron imaging information to provide high confidence that the shielded item is consistent with the host's declaration. The combination of material identification information and the shape and configuration of the item are very difficult to spoof. When used at various points in the warhead dismantlement sequence, the information complimented by tags and seals can be used to track subassembly and piece part information as the disassembly occurs. The neutron transmission imaging has been developed during the last seven years and the signature analysis over the last several decades. The FNMIS is the culmination of the effort to put the technology in a usable configuration for potential treaty verification purposes.

  7. Protection and control of nuclear materials

    International Nuclear Information System (INIS)

    Jalouneix, J.; Winter, D.

    2007-01-01

    In the framework of the French regulation on nuclear materials possession, the first liability is the one of operators who have to know at any time the quantity, quality and localization of any nuclear material in their possession. This requires an organization of the follow up and of the inventory of these materials together with an efficient protection against theft or sabotage. The French organization foresees a control of the implementation of this regulation at nuclear facilities and during the transport of nuclear materials by the minister of industry with the sustain of the institute of radiation protection and nuclear safety (IRSN). This article presents this organization: 1 - protection against malevolence; 2 - national protection and control of nuclear materials: goals, administrative organization, legal and regulatory content (authorization, control, sanctions), nuclear materials protection inside facilities (physical protection, follow up and inventory, security studies), protection of nuclear material transports (physical protection, follow up), control of nuclear materials (inspection at facilities, control of nuclear material measurements, inspection of nuclear materials during transport); 3 - international commitments of France: non-proliferation treaty, EURATOM regulation, international convention on the physical protection of nuclear materials, enforcement in France. (J.S.)

  8. Perspective on transporting nuclear materials

    International Nuclear Information System (INIS)

    Wymer, R.G.

    1975-01-01

    An evaluation is made of the material flow to be expected up to the year 2000 to and from the various steps in the nuclear cycle. These include the reactors, reprocessing plants, enrichment plants, U mills, U conversion plants, and fuel fabrication plants. A somewhat more-detailed discussion is given of the safety engineering that goes into the design of containers and packages and the selection of the mode of transportation. The relationship of shipping to siting and transportation accidents is considered briefly

  9. Proceedings of the international symposium on materials testing reactors

    International Nuclear Information System (INIS)

    Ishihara, Masahiro; Kawamura, Hiroshi

    2009-01-01

    This report is the Proceedings of the International Symposium on Materials Testing Reactors hosted by Japan Atomic Energy Agency (JAEA). The symposium was held on July 16 to 17, 2008, at the Oarai Research and Development Center of JAEA. This symposium was also held for the 40th anniversary ceremony of Japan Materials Testing Reactor (JMTR) from achieving its first criticality. The objective of the symposium is to exchange the information on current status, future plan and so on among each testing reactors for the purpose of mutual understanding. There were 138 participants from Argentina, Belgium, France, Indonesia, Kazakhstan, Korea, the Russian Federation, Sweden, the United State, Vietnam and Japan. The symposium was divided into four technical sessions and three topical sessions. Technical sessions addressed the general topics of 'status and future plan of materials testing reactors', 'material development for research and testing reactors', irradiation technology (including PIE technology)' and 'utilization with materials testing reactors', and 21 presentations were made. Also the topical sessions addressed 'establishment of strategic partnership', 'management on re-operation work at reactor trouble' and 'basic technology for neutron irradiation tests in MTRs', and panel discussion was made. The 21 of the presented papers are indexed individually. (J.P.N.)

  10. Statistical methods for nuclear material management

    Energy Technology Data Exchange (ETDEWEB)

    Bowen W.M.; Bennett, C.A. (eds.)

    1988-12-01

    This book is intended as a reference manual of statistical methodology for nuclear material management practitioners. It describes statistical methods currently or potentially important in nuclear material management, explains the choice of methods for specific applications, and provides examples of practical applications to nuclear material management problems. Together with the accompanying training manual, which contains fully worked out problems keyed to each chapter, this book can also be used as a textbook for courses in statistical methods for nuclear material management. It should provide increased understanding and guidance to help improve the application of statistical methods to nuclear material management problems.

  11. Statistical methods for nuclear material management

    International Nuclear Information System (INIS)

    Bowen, W.M.; Bennett, C.A.

    1988-12-01

    This book is intended as a reference manual of statistical methodology for nuclear material management practitioners. It describes statistical methods currently or potentially important in nuclear material management, explains the choice of methods for specific applications, and provides examples of practical applications to nuclear material management problems. Together with the accompanying training manual, which contains fully worked out problems keyed to each chapter, this book can also be used as a textbook for courses in statistical methods for nuclear material management. It should provide increased understanding and guidance to help improve the application of statistical methods to nuclear material management problems

  12. Federal Court of Administration dismissed appeals in nuclear power plant proceedings

    International Nuclear Information System (INIS)

    Anon.

    1980-01-01

    On July 18, 1980 the Federal Court of Administration handed down several decisions made in proceedings on nuclear power stations. It dismissed the appeal field by the complaining party. 1. In the proceedings concerning the Kruemmel reactor being about to be completed, the World Association for the Protecteion of Life was again denied the right to file a complaint. 2. In the proceedings concerning the nuclear power station under construction at Muelheim-Kaerlich, the objections raised were regarded as being insufficient for repealing the licence. 3. In the proceedings concerning the nuclear power staion at Wyhl which has not been built yet, the objections raised were declared not to be sufficiently substantiated in time. The written opinions of all proceedings are not yet available. (HSCH) [de

  13. Proceedings of the 1984 DOE nuclear reactor and facility safety conference. Volume II

    Energy Technology Data Exchange (ETDEWEB)

    1984-01-01

    This report is a collection of papers on reactor safety. The report takes the form of proceedings from the 1984 DOE Nuclear Reactor and Facility Safety Conference, Volume II of two. These proceedings cover Safety, Accidents, Training, Task/Job Analysis, Robotics and the Engineering Aspects of Man/Safety interfaces.

  14. Proceedings of the 1984 DOE nuclear reactor and facility safety conference. Volume II

    International Nuclear Information System (INIS)

    1984-01-01

    This report is a collection of papers on reactor safety. The report takes the form of proceedings from the 1984 DOE Nuclear Reactor and Facility Safety Conference, Volume II of two. These proceedings cover Safety, Accidents, Training, Task/Job Analysis, Robotics and the Engineering Aspects of Man/Safety interfaces

  15. Proceedings of the workshop on cool building materials

    Energy Technology Data Exchange (ETDEWEB)

    Akbari, H.; Fishman, B. [Lawrence Berkeley Lab., CA (United States); Frohnsdorff, G. [National Inst. of Standards and Technology (NEL), Gaithersburg, MD (United States). Building Materials Div.] [eds.

    1994-04-01

    The Option 9, Cool Communities, of the Clinton-Gore Climate Change Action Plan (CCAP) calls for mobilizing community and corporate resources to strategically plant trees and lighten the surfaces of buildings and roads in order to reduce cooling energy use of the buildings. It is estimated that Cool Communities Project will potentially save over 100 billion kilowatt-hour of energy per year corresponding to 27 million tons of carbon per year by the year 2015. To pursue the CCAP`s objectives, Lawrence Berkeley Laboratory (LBL) on behalf of the Department of Energy and the Environmental Protection Agency, in cooperation with the Building and Fire Research Laboratory of the National Institute of Standards and Technology (NIST), organized a one-day meeting to (1) explore the need for developing a national plan to assess the technical feasibility and commercial potential of high-albedo (``cool``) building materials, and if appropriate, to (2) outline a course of action for developing the plan. The meeting took place on February 28, 1994, in Gaithersburg, Maryland. The proceedings of the conference, Cool Building Materials, includes the minutes of the conference and copies of presentation materials distributed by the conference participants.

  16. Nuclear power plant cable materials :

    Energy Technology Data Exchange (ETDEWEB)

    Celina, Mathias C.; Gillen, Kenneth T; Lindgren, Eric Richard

    2013-05-01

    A selective literature review was conducted to assess whether currently available accelerated aging and original qualification data could be used to establish operational margins for the continued use of cable insulation and jacketing materials in nuclear power plant environments. The materials are subject to chemical and physical degradation under extended radiationthermal- oxidative conditions. Of particular interest were the circumstances under which existing aging data could be used to predict whether aged materials should pass loss of coolant accident (LOCA) performance requirements. Original LOCA qualification testing usually involved accelerated aging simulations of the 40-year expected ambient aging conditions followed by a LOCA simulation. The accelerated aging simulations were conducted under rapid accelerated aging conditions that did not account for many of the known limitations in accelerated polymer aging and therefore did not correctly simulate actual aging conditions. These highly accelerated aging conditions resulted in insulation materials with mostly inert aging processes as well as jacket materials where oxidative damage dropped quickly away from the air-exposed outside jacket surface. Therefore, for most LOCA performance predictions, testing appears to have relied upon heterogeneous aging behavior with oxidation often limited to the exterior of the cable cross-section a situation which is not comparable with the nearly homogenous oxidative aging that will occur over decades under low dose rate and low temperature plant conditions. The historical aging conditions are therefore insufficient to determine with reasonable confidence the remaining operational margins for these materials. This does not necessarily imply that the existing 40-year-old materials would fail if LOCA conditions occurred, but rather that unambiguous statements about the current aging state and anticipated LOCA performance cannot be provided based on

  17. Proceedings of the eighth Nuclear and Particle Physics Conference (NUPPAC-2011)

    International Nuclear Information System (INIS)

    2011-11-01

    The proceeding contains of 287 pages, the available maertial of 50 contributions: and covering of conference topics: Plenary, Invited, Keynote Talks. Nuclear Structure and Spectroscopy. Nuclear Scattering and Reactions. Neutron and Reactor Physics. Relativistic and Quantum Physics. Detectors and Instrumentation. Nuclear Analytical Techniques. Radiation Measurement and Dosimetry.

  18. Proceedings of the 1. General Congress of Nuclear Energy. v. 2

    International Nuclear Information System (INIS)

    1986-01-01

    The proceedings of I General Congress of Nuclear Energy are presented. All fields related to nuclear energy are enclosed. In the second part the following fields are shown: reactor instrumentation and control, nuclear medicine, radioisotopes uses, fuel cycle and radiation protection. (M.C.K.) [pt

  19. 10. National Nuclear Science and Technology Congress Proceedings Book, Volume 2

    International Nuclear Information System (INIS)

    2009-01-01

    X. National Nuclear Science and Technologies Congress was held on 6-9 October 2009 in Mugla, Turkey in the course of collaborative organization undertaken by Turkish Atomic Energy Authority, Mugla University and Sitki Kocman Foundation. This second volume of Proceedings Book contains 91 submitted presentations and 51 of them are full texts on applications of basic nuclear sciences, nuclear energy and safety.

  20. Proceedings of the 2000 International Conference on Nuclear Energy in Central Europe

    International Nuclear Information System (INIS)

    Mavko, B.; Cizelj, L.; Kovac, M.

    2000-01-01

    International Conference Nuclear Energy in Central Europe is an annual meeting of the Nuclear Society of Slovenia. The proceedings contain 108 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region. Topics are: thermal hydraulics, severe accidents, probabilistic safety assessment (PSA), nuclear waste, safety analyses, nuclear power plant operation, structural integrity and aging, nuclear energy and public, other related topics, research reactors, education and training and Monte Carlo transport calculations

  1. Proceedings of the 27. annual conference of the Canadian Nuclear Association

    International Nuclear Information System (INIS)

    1987-01-01

    The proceedings comprise 33 papers on the following subjects: progress in nuclear energy, regulation, public relations, the IAEA, economic goals and operating lessons, performance goals. The individual papers have been abstracted separately

  2. Proceedings of the Tenth Symposium on Space Nuclear Power and Propulsion

    International Nuclear Information System (INIS)

    El-Genk, M.S.; Hoover, M.D.

    1993-01-01

    This symposium included topics on space nuclear power. Various aspectsof design of propulsion and power systems were presented. From theProceedings, two hundred and twelve papers were abstracted for the database

  3. Enduring Nuclear Fuel Cycle, Proceedings of a panel discussion

    Energy Technology Data Exchange (ETDEWEB)

    Walter, C. E., LLNL

    1997-11-18

    The panel reviewed the complete nuclear fuel cycle in the context of alternate energy resources, energy need projections, effects on the environment, susceptibility of nuclear materials to theft, diversion, and weapon proliferation. We also looked at ethical considerations of energy use, as well as waste, and its effects. The scope of the review extended to the end of the next century with due regard for world populations beyond that period. The intent was to take a long- range view and to project, not forecast, the future based on ethical rationales, and to avoid, as often happens, long-range discussions that quickly zoom in on only the next few decades. A specific nuclear fuel cycle technology that could satisfy these considerations was described and can be applied globally.

  4. Nuclear material measurement system in Brazil

    International Nuclear Information System (INIS)

    Almeida, S.G. de.

    1988-01-01

    The description of the activities developed at the Safeguards Laboratory of Brazilian Nuclear Energy Commission is done. The methods and techniques used for measuring and evaluating nuclear materials and facilities are presented. (E.G.) [pt

  5. Proceedings of the Scientific Meeting and Presentation on Basic Research in Nuclear of the Science and Technology part III : Radioactive Waste Management and Environment

    International Nuclear Information System (INIS)

    Kamsul Abraha; Yateman Arryanto; Sri Jauhari S; Agus Taftazani; Kris Tri Basuki; Djoko Sardjono, Ign.; Sukarsono, R.; Samin; Syarip; Suryadi, MS; Sardjono, Y.; Tri Mardji Atmono; Dwiretnani Sudjoko; Tjipto Sujitno, BA.

    2007-08-01

    The Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is a routine activity held by Centre for Accelerator Technology and Material Process, National Nuclear Energy Agency, for monitoring the research activity which achieved in National Nuclear Energy Agency. The Meeting was held in Yogyakarta on July 10, 2007. The proceedings contains papers presented on the meeting about Radioactive Waste Management and Environment and there are 25 papers which have separated index. The proceedings is the third part of the three parts which published in series. (PPIN)

  6. National Public Information Symposium on Peaceful Uses of Nuclear Energy, NUC Info' 2000. Radioactive Waste Management and Site Restoration in Uranium Industry. Proceedings. Volume 2

    International Nuclear Information System (INIS)

    Dobos, Ion; Comsa, Olivia

    2000-01-01

    These proceedings published in two volumes contain materials presented at the National Public Information Symposium on Peaceful Uses of Nuclear Energy, NUC Info' 2000. Radioactive Waste Management and Site Restoration in Uranium Industry - held on 5th September to 8th September 2000 at Baita - Bihor, Romania. The proceedings are structured in 4 sections: 1. Management of radioactive wastes arising from uranium mining, milling and decommissioning; 2. Uranium mine closing down; 3. Environmental restoration of uranium mining and milling sites; 4. Management of radioactive wastes arising from nuclear applications. The contributions in this volume debate the issues of environment restoration at uranium ore mining and management of radioactive wastes resulted from nuclear applications

  7. Nuclear material management: challenges and prospects

    International Nuclear Information System (INIS)

    Rieu, J.; Besnainou, J.; Leboucher, I.; Chiguer, M.; Capus, G.; Greneche, D.; Durret, L.F.; Carbonnier, J.L.; Delpech, M.; Loaec, Ch.; Devezeaux de Lavergne, J.G.; Granger, S.; Devid, S.; Bidaud, A.; Jalouneix, J.; Toubon, H.; Pochon, E.; Bariteau, J.P.; Bernard, P.; Krellmann, J.; Sicard, B.

    2008-01-01

    The articles in this dossier were derived from the papers of the yearly S.F.E.N. convention, which took place in Paris, 12-13 March 2008. They deal with the new challenges and prospects in the field of nuclear material management, throughout the nuclear whole fuel cycle, namely: the institutional frame of nuclear materials management, the recycling, the uranium market, the enrichment market, the different scenarios for the management of civil nuclear materials, the technical possibilities of spent fuels utilization, the option of thorium, the convention on the physical protection of nuclear materials and installations, the characterisation of nuclear materials by nondestructive nuclear measurements, the proliferation from civil installations, the use of plutonium ( from military origin) and the international agreements. (N.C.)

  8. Proceedings of NUCLEAR 2013 the 6th annual international conference on sustainable development through nuclear research and education. Part 2/3

    International Nuclear Information System (INIS)

    Constantin, Marin; Turcu, Ilie

    2013-01-01

    The proceedings of the NUCLEAR 2013 international conference on sustainable development through nuclear research and education held at INR-Pitesti on May, 22-24 2013 contain 79 communications presented in two plenary sessions. The sections of conferecnce are adressing the following items: Section I.1 Nuclear Safety & Severe Accidents (15 papers), Section I.2 Nuclear Reactors & Generation IV (15 papers), Section I.3 Nuclear Technologies & Materials (28 papers), Section II.1 Radioprotection (6 papers), Section II.2 Radioactive Waste Management (8 papers), Section II.3 Air, Water & Soil Protection (5 papers) and Section III Sustainable Development (4 papers) These papers are presented as abstracts in 'Nuclear 2013 - BOOK of ABSTRACTS', separately processed

  9. Proceedings of NUCLEAR 2013 the 6th annual international conference on sustainable development through nuclear research and education. Part 3/3

    International Nuclear Information System (INIS)

    Constantin, Marin; Turcu, Ilie

    2013-01-01

    The proceedings of the NUCLEAR 2013 international conference on sustainable development through nuclear research and education held at INR-Pitesti on May, 22-24 2013 contain 79 communications presented in two plenary sessions. The sections of conferecnce are adressing the following items: Section I.1 Nuclear Safety & Severe Accidents (15 papers), Section I.2 Nuclear Reactors & Generation IV (15 papers), Section I.3 Nuclear Technologies & Materials (28 papers), Section II.1 Radioprotection (6 papers), Section II.2 Radioactive Waste Management (8 papers), Section II.3 Air, Water & Soil Protection (5 papers) and Section III Sustainable Development (4 papers) These papers are presented as abstracts in 'Nuclear 2013 - BOOK of ABSTRACTS', separately processed

  10. Nuclear power plant life management. Proceedings of a symposium

    International Nuclear Information System (INIS)

    2003-01-01

    Presently, an area of major interest of the IAEA is the management of the nuclear power plant (NPP) life cycle from concept development to decommissioning and disposal, with the primary objective of maximising the return on investment in nuclear facilities through efficient operation of NPPs. 441 NPPs, with a capacity of about 350GW(e) supplied 16% of global electricity in 2002. Of these, about 300 NPPs have been in operation for 15 years or more and these older units with partially or fully amortized capital costs have proven to be the most profitable. Moreover, there are no significant safety or economic reasons not to continue the operation of well managed NPPs over a longer period and consequently the issues of plant life management and license extension are receiving increasing emphasis in many countries. Forecasts of nuclear power growth over the next two decades range from 350GW(e) in the worst case to 500GW(e) in the best case. This will need additional personnel and expansion of the infrastructure in the developing countries, particularly as much of the new demand growth is forecast to take place outside the countries where most of the existing infrastructure resides. All aspects of NPP life cycle management are addressed by the IAEA and are briefly described in these proceedings. The IAEA Technical Working Group on Life Management of Nuclear Power Plants (TWG-LMNPP) recommended, during its regular meeting in February 1999, that the IAEA should consider holding a symposium on this subject area in 2002. This TWG-LMNPP Proposal was approved and, this symposium was held, attended by 138 participants from 32 Member States and 2 international organizations. The objectives of the symposium were as follows: Emphasise the role of NPP life management programmes in assuring a safe and reliable NPP operating cycle; Identify progress in methodological and technological developments for managing ageing processes and understanding ageing mechanisms; Provide a forum for

  11. Techniques and methods in nuclear materials traceability

    International Nuclear Information System (INIS)

    Persiani, P.J.

    1996-01-01

    The nonproliferation community is currently addressing concerns that the access to special nuclear materials may increase the illicit trafficking in weapons-usable materials from civil and/or weapons material stores and/or fuel cycles systems. Illicit nuclear traffic usually involves reduced quantities of nuclear materials perhaps as samplings of a potential protracted diversionary flow from sources to users. To counter illicit nuclear transactions requires the development of techniques and methods in nuclear material traceability as an important phase of a broad forensic analysis capability. This report discusses how isotopic signatures and correlation methods were applied to determine the origins of Highly Enriched Uranium (HEU) and Plutonium samples reported as illicit trafficking in nuclear materials

  12. Proceedings of the specialists' meeting on delayed neutron nuclear data

    International Nuclear Information System (INIS)

    Katakura, Jun-ichi

    1999-07-01

    This report is the Proceedings of the Specialists' Meeting on Delayed Neutron Nuclear Data. The meeting was held on January 28-29, 1999, at the Tokai Research Establishment of Japan Atomic Energy Research Institute with the participation of thirty specialists, who are evaluators, theorist, experimentalists. Although the fraction of the delayed neutron is no more than 1% in the total neutrons emitted in the fission process, it plays an important roll in the control of fission reactor. In the meeting, the following topics were reported: the present status of delayed neutron data in the major evaluated data libraries, measurements of effective delayed neutron fraction using FCA (Fast Critical Assembly) and TCA (Tank-type Critical Assembly) and their analyses, sensitivity analysis for fast reactor, measurements of delayed neutron emission from actinides and so on. As another topics, delayed neutron in transmutation system and fission yield data were also presented. Free discussion was held on the future activity of delayed neutron data evaluation. The discussion was helpful for the future activity of the delayed neutron working group of JNDC aiming to the evaluation of delayed neutron data for JENDL-3.3. The 15 of the presented papers are indexed individually. (J.P.N.)

  13. 76 FR 76728 - Benefits and Burdens of Requiring Commenters To File Cited Materials in Rulemaking Proceedings as...

    Science.gov (United States)

    2011-12-08

    ... Requiring Commenters To File Cited Materials in Rulemaking Proceedings as Further Reform To Enhance Record... materials they cite in pleadings submitted in rulemaking proceedings, so that those materials are more... should require commenters to file materials they cite in pleadings submitted in rulemaking proceedings...

  14. Proceedings of the 2013 International Conference on Mathematics and Computational Methods Applied to Nuclear Science and Engineering - M and C 2013

    International Nuclear Information System (INIS)

    2013-01-01

    The Mathematics and Computation Division of the American Nuclear (ANS) and the Idaho Section of the ANS hosted the 2013 International Conference on Mathematics and Computational Methods Applied to Nuclear Science and Engineering (M and C 2013). This proceedings contains over 250 full papers with topics ranging from reactor physics; radiation transport; materials science; nuclear fuels; core performance and optimization; reactor systems and safety; fluid dynamics; medical applications; analytical and numerical methods; algorithms for advanced architectures; and validation verification, and uncertainty quantification

  15. Proceedings of the 2013 International Conference on Mathematics and Computational Methods Applied to Nuclear Science and Engineering - M and C 2013

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-07-01

    The Mathematics and Computation Division of the American Nuclear (ANS) and the Idaho Section of the ANS hosted the 2013 International Conference on Mathematics and Computational Methods Applied to Nuclear Science and Engineering (M and C 2013). This proceedings contains over 250 full papers with topics ranging from reactor physics; radiation transport; materials science; nuclear fuels; core performance and optimization; reactor systems and safety; fluid dynamics; medical applications; analytical and numerical methods; algorithms for advanced architectures; and validation verification, and uncertainty quantification.

  16. Nuclear material control systems for nuclear power plants

    International Nuclear Information System (INIS)

    1975-06-01

    Paragraph 70.51(c) of 10 CFR Part 70 requires each licensee who is authorized to possess at any one time special nuclear material in a quantity exceeding one effective kilogram to establish, maintain, and follow written material control and accounting procedures that are sufficient to enable the licensee to account for the special nuclear material in his possession under license. While other paragraphs and sections of Part 70 provide specific requirements for nuclear material control systems for fuel cycle plants, such detailed requirements are not included for nuclear power reactors. This guide identifies elements acceptable to the NRC staff for a nuclear material control system for nuclear power reactors. (U.S.)

  17. Proceedings of the 13. Workshop on Nuclear Physics in Brazil

    International Nuclear Information System (INIS)

    1990-01-01

    Theoretical and experimental studies on nuclear structure, nuclear matter, scattering, nuclear reactions, radioactive decay, nuclear properties and nuclear models are presented. Studies on radiation protection, radiation detectors, spectroscopy and elementary particles area also presented. (M.C.K.)

  18. Tracer techniques in estimating nuclear materials holdup

    International Nuclear Information System (INIS)

    Pillay, K.K.S.

    1987-01-01

    Residual inventory of nuclear materials remaining in processing facilities (holdup) is recognized as an insidious problem for safety of plant operations and safeguarding of special nuclear materials (SNM). This paper reports on an experimental study where a well-known method of radioanalytical chemistry, namely tracer technique, was successfully used to improve nondestructive measurements of holdup of nuclear materials in a variety of plant equipment. Such controlled measurements can improve the sensitivity of measurements of residual inventories of nuclear materials in process equipment by several orders of magnitude and the good quality data obtained lend themselves to developing mathematical models of holdup of SNM during stable plant operations

  19. International conference on composite materials and energy: Proceedings. Enercomp 95

    International Nuclear Information System (INIS)

    Anon.

    1995-01-01

    World demand for composite materials is continuously increasing. High strength and rigidity, associated with light weight, are the key factors for composites' success. These materials find numerous applications in all sectors of industry. Presently, a sector of particular interest in terms of demand for composite materials is the energy industry. More and more applications are found in the field of the forms of energy: electrical, petroleum, gas, nuclear, solar and wind. The topics addressed in various sessions of the conference cover potential applications of the entire range of polymer, metal and ceramic composites in all sectors of energy. Papers are divided into sessions covering the following topics: properties; design and analysis; fracture; fatigue and long-term performance; new materials; innovative processing; liquid molding; joining and repairs; radiation curing; recycling; development in ceramic materials; innovations in metallic materials; metal-matrix composites; nondestructive evaluation; energy savings in transportation; pressure vessels and piping; wind energy applications; electrical components; concrete applications; power plant applications; and new materials in the energy field. Most of the papers have been processed separately for inclusion on the data base

  20. Proceedings of the 8. National Seminar on Technology and Safety of Nuclear Power Plants and Nuclear Facilities

    International Nuclear Information System (INIS)

    Antariksawan, Anhar R.; Soetrisnanto, Arnold Y.; Aziz, Ferhat; Untoro, Pudji; Su'ud, Zaki; Zarkasi, Amin Santosa; Umar, Faraz H.; Teguh Bambang; Hafnan, M.; Mustafa, Bustani; Rosfian, H.

    2002-10-01

    The eight proceeding of National Seminar on Technology and Safety of Nuclear Power Plant and Nuclear Facilities held by National Atomic Energy Agency and University of Trisakti. The aims of Seminar is to exchange and disseminate information about safety and nuclear Power Plant Temperature Reactor and Application for National Development sustain able and High Technology. This Seminar covers all aspect Technology, Power Reactor : Research Reactor; High Temperature Reactor and Nuclear Facilities. There are 33 articles have separated index

  1. Proceedings of the 4th international symposium on material testing reactors

    Energy Technology Data Exchange (ETDEWEB)

    Ishihara, Masahiro; Suzuki, Masahide [Japan Atomic Energy Agency, Oarai Research and Development Center, Oarai, Ibaraki (Japan)

    2012-03-15

    This report is the Proceedings of the fourth International Symposium on Material Testing Reactors hosted by Japan Atomic Energy Agency (JAEA). The first symposium was held on 2008, at the Oarai Research and Development Center of JAEA, the second, 2009, Idaho National Laboratory (INL) of United States and the third 2010, Nuclear Research Institute (NRI) in Czech Republic to exchange information for deep mutual understanding of material testing reactors. The fourth symposium was originally scheduled to be held INVAP in Argentina. However, the aftermath of volcanic explosion at Chili forced the symposium to change place. Total 111 participants attended from Argentina, Belgium, France, Germany, Indonesia, Malasia, Korea, South Africa, Switzerland, the United State and Japan. This symposium addressed the general topics of 'status and future plan of material testing reactors', 'advancement of irradiation technology', 'expansion of industry use(RI)', 'facility, upgrade, aging management', 'new generation MTR', 'advancement of PIE technology', 'development of advanced driver fuel', and 'nuclear human resource development(HRD) for next generation', and 39 presentations were made. Furthermore, three topics, 'Necessity of cooperation for Mo-99 production by (n,gamma) reaction', 'Necessity of standardization of irradiation technology' and 'Conceptual design of next generation materials testing reactor by collaboration', were selected and discussed. (author)

  2. Proceedings of the 4th international symposium on material testing reactors

    International Nuclear Information System (INIS)

    Ishihara, Masahiro; Suzuki, Masahide

    2012-03-01

    This report is the Proceedings of the fourth International Symposium on Material Testing Reactors hosted by Japan Atomic Energy Agency (JAEA). The first symposium was held on 2008, at the Oarai Research and Development Center of JAEA, the second, 2009, Idaho National Laboratory (INL) of United States and the third 2010, Nuclear Research Institute (NRI) in Czech Republic to exchange information for deep mutual understanding of material testing reactors. The fourth symposium was originally scheduled to be held INVAP in Argentina. However, the aftermath of volcanic explosion at Chili forced the symposium to change place. Total 111 participants attended from Argentina, Belgium, France, Germany, Indonesia, Malasia, Korea, South Africa, Switzerland, the United State and Japan. This symposium addressed the general topics of 'status and future plan of material testing reactors', 'advancement of irradiation technology', 'expansion of industry use(RI)', 'facility, upgrade, aging management', 'new generation MTR', 'advancement of PIE technology', 'development of advanced driver fuel', and 'nuclear human resource development(HRD) for next generation', and 39 presentations were made. Furthermore, three topics, 'Necessity of cooperation for Mo-99 production by (n,gamma) reaction', 'Necessity of standardization of irradiation technology' and 'Conceptual design of next generation materials testing reactor by collaboration', were selected and discussed. (author)

  3. Proceedings of the European Forum on Nuclear Waste governance

    International Nuclear Information System (INIS)

    2004-01-01

    Electronuclear production is a component of France's and Europe's energy supplies. However, populations remain worried as nuclear electricity produces dangerous radioactive waste for many generations. They are all the more worried so as they are not enough informed and involved in decision-making. After having analysed in 2003 the issue of national choices and their compatibility with a European directive, the European talks' ambition is to clarify the responsibilities of the different stakeholders for a good governance. Indeed, these have to make their strategies for everlasting solutions understood, inform about costs that correspond to an efficient and long-term management of nuclear waste and about their financing. How are roles shared between States, producers, managers, researchers and local entities? The European Talks has organised the dialog between stakeholders from several member States of the EU around two series of questions: - What are industrial and economic actors strategies? In which public framework are they included? How do they anticipate the future? The speakers have analysed their own experiences in order to examine what could an efficient and fair regulation and costs sharing be. - What are nuclear stakeholders commitments on the field? What kind of projects could be initiated? How could these stakeholders become partners for sustainable development? Here again, experiences have been shared in the perspective of mobilizing energies on concrete projects. This document is the proceedings of this second European Forum on this topic. Content: 1 - Opening by Christian Namy, president of the Meuse General Council; Message from Patrick Devedjian, French vice- minister of Industry. 2 - First round table 'The stakeholders strategy and their management of nuclear waste in France and in Europe' (Moderator: Alejo Vidal Quadras Roca, vice-president of the European Parliament, Spain): Speaker: Yves Le Bars, chairman, ANDRA, Discussants: Jozsef Hegyhati

  4. Nuclear heat applications: design aspects and operating experience. Proceedings of four technical meetings held between December 1995 and April 1998

    International Nuclear Information System (INIS)

    1998-11-01

    Proven to be safe, reliable, economic and having minimum impact on the environment, nuclear energy is playing an important role in electricity generation producing 175 of the world's electricity. But since most of the world's energy consumption is in the form of heat the market for nuclear heat has already been recognised. Considering the growing experience in application of power reactors for district heating, industrial processes and water desalination IAEA is periodically reviewing progress and new developments of nuclear heat applications. This proceedings includes the papers presented at the following four meetings: Advisory group meeting and consultancy on experience with nuclear heat applications: district heating, process heat and desalination, 13-15 December 1995 and 7-9 february 1996; Advisory group meeting on technology, design and safety aspects of non-electrical application of nuclear energy, 20-24 October 1997; Advisory group meeting on operational modes of nuclear desalination plants, 3-5 November 1997; Advisory group meeting on materials and equipment for the coupling interfaces of nuclear reactors with desalination and district heating plants, 21-23 April 1998. It is structured according to the subject areas: (1) design an safety aspects of nuclear heat application, (2) operational and material aspects of nuclear heat application and (3) operational experience with nuclear heat application. Each paper is described by a separate abstract

  5. Proceedings of the 1st JAEA/KAERI information exchange meeting on HTGR and nuclear hydrogen technology

    International Nuclear Information System (INIS)

    Sato, Hiroyuki; Sakaba, Nariaki; Nishihara, Tetsuo; Yan, Xing L.; Hino, Ryutaro

    2007-03-01

    Japan Atomic Energy Agency (JAEA) has completed an implementation with Korea Atomic Energy Research Institute (KAERI) on HTGR and nuclear hydrogen technology, 'The Implementation of Cooperative Program in the Field of Peaceful Uses of Nuclear Energy between KAERI and JAEA. 'To facilitate efficient technology development on HTGR and nuclear hydrogen by the IS process, an information exchange meeting was held at the Oarai Research and Development Center of JAEA on August 28-30, 2006 under Program 13th of the JAEA/KAERI Implementation, 'Development of HTGR and Nuclear Hydrogen Technology'. JAEA and KAERI mutually showed the status and future plan of the HTTR (High-Temperature Engineering Test Reactor) project in Japan and of the NHDD (Nuclear Hydrogen Development and Demonstration) project in Korea, respectively, and discussed collaboration items. This proceedings summarizes all materials of presented technical discussions on HTGR and hydrogen production technology as well as the meeting briefing including collaboration items. (author)

  6. Proceedings of the International Conference on Applications of High Precision Atomic and Nuclear Methods

    International Nuclear Information System (INIS)

    Olariu, Agata; Stenstroem, Kristina; Hellborg, Ragnar

    2005-01-01

    This volume presents the Proceedings of the International Conference on Applications of High Precision Atomic and Nuclear Methods, held in Neptun, Romania from 2nd to 6th of September 2002. The conference was organized by The Center of Excellence of the European Commission: Inter-Disciplinary Research and Applications based on Nuclear and Atomic Physics (IDRANAP) from Horia Hulubei National Institute for Physics and Nuclear Engineering, IFIN-HH, Bucharest-Magurele, Romania. The meeting gathered 66 participants from 25 different laboratories in 11 countries, namely: Belgium, Bulgaria, France, Germany, Hungary, Poland, Portugal, Romania, Slovakia and Sweden. Non European delegate came from Japan. The topics covered by the conference were as follows: - Environment: air, water and soil pollution, pollution with heavy elements and with radioisotopes, bio-monitoring (10 papers); - Radionuclide metrology (10 papers); - Ion beam based techniques for characterization of materials surface, ERDA, PIXE, PIGE, computer simulations, materials modifications, wear, corrosion (10 papers) ; - Accelerator Mass Spectrometry and applications in environment, archaeology, and medicine (7 papers); - Application of neutron spectrometry in condensed matter (1 paper); - Advanced techniques, facilities and applications (11). Seventeen invited speakers covered through overview talks the main parts of these topics. The book contains the overview talks, oral contributions and poster contributions

  7. Uncertainty estimation in nuclear material weighing

    Energy Technology Data Exchange (ETDEWEB)

    Thaure, Bernard [Institut de Radioprotection et de Surete Nucleaire, Fontenay aux Roses, (France)

    2011-12-15

    The assessment of nuclear material quantities located in nuclear plants requires knowledge of additions and subtractions of amounts of different types of materials. Most generally, the quantity of nuclear material held is deduced from 3 parameters: a mass (or a volume of product); a concentration of nuclear material in the product considered; and an isotopic composition. Global uncertainties associated with nuclear material quantities depend upon the confidence level of results obtained in the measurement of every different parameter. Uncertainties are generally estimated by considering five influencing parameters (ISHIKAWA's rule): the material itself; the measurement system; the applied method; the environmental conditions; and the operator. A good practice guide, to be used to deal with weighing errors and problems encountered, is presented in the paper.

  8. Development of nuclear material accountancy control system

    International Nuclear Information System (INIS)

    Hirosawa, Naonori; Kashima, Sadamitsu; Akiba, Mitsunori

    1992-01-01

    PNC is developing a wide area of nuclear fuel cycle. Therefore, much nuclear material with a various form exists at each facility in the Works, and the controls of the inventory changes and the physical inventories of nuclear material are important. Nuclear material accountancy is a basic measure in safeguards system based on Non-Proliferation Treaty (NPT). In the light of such importance of material accountancy, the data base of nuclear material control and the material accountancy report system for all facilities has been developed by using the computer. By this system, accountancy report to STA is being presented certainly and timely. Property management and rapid corresponding to various inquiries can be carried out by the data base system which has free item searching procedure. (author)

  9. Proceedings of the seminar on nuclear safety research and the workshop on reactor safety research

    International Nuclear Information System (INIS)

    2001-07-01

    The seminar on the nuclear safety research was held on November 20, 2000 according to the start of new five year safety research plan (FY2001-2005: established by Nuclear Safety Commission) with 79 participants. In the seminar, Commissioner Dr. Kanagawa gave the outline of the next five year safety research plan. Following this presentation, progresses and future scopes of safety researches in the fields of reactor facility, fuel cycle facility, radioactive waste and environmental impact on radiation at Japan Atomic Energy Research Institute (JAERI) were reported. After the seminar, the workshop on reactor safety research was held on November 21-22, 2000 with 141 participants. In the workshop, four sessions titled safety of efficient and economic utilization of nuclear fuel, safety related to long-term utilization of power reactors, research on common safety-related issues and toward further improvement of nuclear safety were organized and, outcomes and future perspectives in these wide research R and D in the related area at other organizations including NUPEC, JAPEIC and Kansai Electric Power Co. was presented in each session. This report compiles outlines of the presentations and used materials in the seminar and the workshop to form the proceedings for the both meetings. (author)

  10. The proceedings of China-Japan workshop on nuclear waste management and reprocessing

    International Nuclear Information System (INIS)

    2000-01-01

    China-Japan workshop on Nuclear Waste Management and Reprocessing held by sponsors, Nuclear Chemical Engineering Association, Chinese nuclear Society and Division of nuclear Fuel Cycle and Environment, Atomic Energy Society of Japan and by co-sponsor, Nuclear and Radiochemistry Association, Chinese Nuclear Society, on April 5-7, 2000, in Beijing, China. The proceedings is published. It collected 34 articles. The contents include nuclear fuel reprocessing, radioactive waste processing and radioactive waste disposal, partitioning and transmutation, radionuclide migration, sorption and diffusion and actinide chemistry

  11. Proceedings of the 8th topical meeting on nuclear code development

    International Nuclear Information System (INIS)

    1993-03-01

    The 8th Topical Meeting on Nuclear Code Development, organized by Committee on Reactor Physics and Nuclear Codes Committee of Japan Atomic Energy Research Institute (JAERI), was held at Tokai Research Establishment of JAERI, on 11th and 12th of November, 1992. In the meeting, 14 papers were presented on the topics of (1) the next generation nuclear reactor design system and (2) advances of the nuclear fuel reprocessing safety analysis codes. These papers are compiled in this proceedings. (author)

  12. Proceedings of the 21st DOE/NRC nuclear air cleaning conference

    International Nuclear Information System (INIS)

    First, M.W.

    1991-02-01

    The 21st meeting of the Department of Energy/Nuclear Regulatory Commission (DOE/NRC) Nuclear Air Cleaning Conference was held in San Diego, CA on August 13--16, 1990. The proceedings have been published as a two volume set. Volume 2 contains sessions covering adsorbents, nuclear codes and standards, modelling, filters, safety, containment venting and a review of nuclear air cleaning programs around the world. Also included is the list of attendees and an index of authors and speakers

  13. International Conference Nuclear Energy in Central Europe 99, V. 1. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Gortnar, O; Stritar, A [Nuclear Society of Slovenia (Slovenia)

    1999-07-01

    International Conference Nuclear Energy in Central Europe is an annual meeting of the Nuclear Society of Slovenia. The proceedings contain 101 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region. Topics are: Reactor Physics, Research Reactors, Thermal Hydraulics, Structural Analysis, Probabilistic Safety Assessment, Severe Accidents, NPP Operation, Nuclear Energy and Public, Radioactive Waste, Radiological Protection and Environmental Issues, Nuclear Methods and Monte Carlo and Deterministic Transport Calculations.

  14. International Conference Nuclear Energy in Central Europe 99, V. 1. Proceedings

    International Nuclear Information System (INIS)

    Gortnar, O.; Stritar, A.

    1999-01-01

    International Conference Nuclear Energy in Central Europe is an annual meeting of the Nuclear Society of Slovenia. The proceedings contain 101 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region. Topics are: Reactor Physics, Research Reactors, Thermal Hydraulics, Structural Analysis, Probabilistic Safety Assessment, Severe Accidents, NPP Operation, Nuclear Energy and Public, Radioactive Waste, Radiological Protection and Environmental Issues, Nuclear Methods and Monte Carlo and Deterministic Transport Calculations

  15. Base isolation for nuclear power and nuclear material facilities

    International Nuclear Information System (INIS)

    Eidinger, J.M.; Kircher, C.A.; Vaidya, N.; Constantinou, M.; Kelly, J.M.; Seidensticker, R.; Tajirian, F.F.; Ovadia, D.

    1989-01-01

    This report serves to document the status of the practice for the use of base isolation systems in the design and construction of nuclear power and nuclear material facilities. The report first describes past and current (1989) applications of base isolation in nuclear facilities. The report then provides a brief discussion of non-nuclear applications. Finally, the report summarizes the status of known base-isolation codes and standards

  16. Metabonomics for detection of nuclear materials processing.

    Energy Technology Data Exchange (ETDEWEB)

    Alam, Todd Michael; Luxon, Bruce A. (University Texas Medical Branch); Neerathilingam, Muniasamy (University Texas Medical Branch); Ansari, S. (University Texas Medical Branch); Volk, David (University Texas Medical Branch); Sarkar, S. (University Texas Medical Branch); Alam, Mary Kathleen

    2010-08-01

    Tracking nuclear materials production and processing, particularly covert operations, is a key national security concern, given that nuclear materials processing can be a signature of nuclear weapons activities by US adversaries. Covert trafficking can also result in homeland security threats, most notably allowing terrorists to assemble devices such as dirty bombs. Existing methods depend on isotope analysis and do not necessarily detect chronic low-level exposure. In this project, indigenous organisms such as plants, small mammals, and bacteria are utilized as living sensors for the presence of chemicals used in nuclear materials processing. Such 'metabolic fingerprinting' (or 'metabonomics') employs nuclear magnetic resonance (NMR) spectroscopy to assess alterations in organismal metabolism provoked by the environmental presence of nuclear materials processing, for example the tributyl phosphate employed in the processing of spent reactor fuel rods to extract and purify uranium and plutonium for weaponization.

  17. Metabonomics for detection of nuclear materials processing

    International Nuclear Information System (INIS)

    Alam, Todd Michael; Luxon, Bruce A.; Neerathilingam, Muniasamy; Ansari, S.; Volk, David; Sarkar, S.; Alam, Mary Kathleen

    2010-01-01

    Tracking nuclear materials production and processing, particularly covert operations, is a key national security concern, given that nuclear materials processing can be a signature of nuclear weapons activities by US adversaries. Covert trafficking can also result in homeland security threats, most notably allowing terrorists to assemble devices such as dirty bombs. Existing methods depend on isotope analysis and do not necessarily detect chronic low-level exposure. In this project, indigenous organisms such as plants, small mammals, and bacteria are utilized as living sensors for the presence of chemicals used in nuclear materials processing. Such 'metabolic fingerprinting' (or 'metabonomics') employs nuclear magnetic resonance (NMR) spectroscopy to assess alterations in organismal metabolism provoked by the environmental presence of nuclear materials processing, for example the tributyl phosphate employed in the processing of spent reactor fuel rods to extract and purify uranium and plutonium for weaponization.

  18. Concepts of IAEA nuclear materials accounting

    International Nuclear Information System (INIS)

    Oakberg, John A.

    2001-01-01

    The paper describes nuclear material accounting from the standpoint of IAEA Safeguards and how this accounting is applied by the Agency. The basic concepts of nuclear material accounting are defined and the way these apply to States with INFCIRC/153-type safeguards agreements is presented. (author)

  19. Radiation Damage in Reactor Materials. Part of the Proceedings of the Symposium on Radiation Damage in Solids and Reactor Materials

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1963-08-15

    Radiation damage has presented a new design parameter for the selection of materials to be used in fuel and cladding elements, moderators, structural components and pressure vessels in nuclear reactors. The severe and novel requirements for certain optimum combinations of physical and nuclear properties have emphasized the need for a better understanding of the basic mechanisms of radiation damage. This knowledge is not only essential for progress in the field of nuclear energy, but has direct applications to space technology and semi-conductor research as well. The IAEA, as part of its programme of promoting nuclear technology, therefore convened the Symposium on Radiation Damage in Solids and Reactor Materials, 7-11 May 1962. At the invitation of, and with generous material assistance from, the Government of Italy, the Symposium was held at Venice. The Symposium was primarily concerned with the investigation of the fundamental processes of radiation that underlie the behaviour of metals, alloys and ceramics that are actually useful or potentially useful reactor materials. Two sessions were devoted to studies of irradiation effects on simple metals, as these effects are easiest to interpret. Other topics included general theory, alloys, fissionable and moderator materials and special experimental techniques for radiation damage studies. The properties influenced by irradiation which were of main concern were those of primary importance to the behaviour of solids as reactor materials (e. g. dimensional stability, phase transformation, radiation hardening, fracture, fission-gas escape from uranium and its compounds). Other properties, such as optical, electrical and magnetic properties, and effects on semiconductors, ionic and other non-metallic crystals are also of interest in that these studies can increase our knowledge of the mechanism of radiation damage in solids and provide a tool for investigation into the physics of the solid state by offering a means of

  20. Radiation Damage in Reactor Materials. Part of the Proceedings of the Symposium on Radiation Damage in Solids and Reactor Materials

    International Nuclear Information System (INIS)

    1963-01-01

    Radiation damage has presented a new design parameter for the selection of materials to be used in fuel and cladding elements, moderators, structural components and pressure vessels in nuclear reactors. The severe and novel requirements for certain optimum combinations of physical and nuclear properties have emphasized the need for a better understanding of the basic mechanisms of radiation damage. This knowledge is not only essential for progress in the field of nuclear energy, but has direct applications to space technology and semi-conductor research as well. The IAEA, as part of its programme of promoting nuclear technology, therefore convened the Symposium on Radiation Damage in Solids and Reactor Materials, 7-11 May 1962. At the invitation of, and with generous material assistance from, the Government of Italy, the Symposium was held at Venice. The Symposium was primarily concerned with the investigation of the fundamental processes of radiation that underlie the behaviour of metals, alloys and ceramics that are actually useful or potentially useful reactor materials. Two sessions were devoted to studies of irradiation effects on simple metals, as these effects are easiest to interpret. Other topics included general theory, alloys, fissionable and moderator materials and special experimental techniques for radiation damage studies. The properties influenced by irradiation which were of main concern were those of primary importance to the behaviour of solids as reactor materials (e. g. dimensional stability, phase transformation, radiation hardening, fracture, fission-gas escape from uranium and its compounds). Other properties, such as optical, electrical and magnetic properties, and effects on semiconductors, ionic and other non-metallic crystals are also of interest in that these studies can increase our knowledge of the mechanism of radiation damage in solids and provide a tool for investigation into the physics of the solid state by offering a means of

  1. Proceeding of the Scientific Presentation on Nuclear Fuel Cycle; Prosiding Presentasi Ilmiah Daur Bahan Bakar Nuklir

    Energy Technology Data Exchange (ETDEWEB)

    Suripto, A; Yuwono, I; Nasution, H; Hersubeno, B J; Amini, S; Sigit,; Cahyono, A [Nuclear Fuel Elements Development Centre, National Atomic Energy Agency, Serpong, Indonesia (Indonesia)

    1996-11-01

    The proceeding contains papers presented on Scientific Presentation on Nuclear Fuel Cycle held in Jakarta, 18-19 March 1996. These are 46 papers resulted from scientific works on various disciplines which have supported to nuclear fuel cycle activities both in and outside National Atomic Energy Agency of Indonesia.(ID)

  2. 10. National Nuclear Science and Technologies Congress Proceedings Full Texts Volume 1

    International Nuclear Information System (INIS)

    2009-01-01

    X. National Nuclear Science and Technologies Congress was held on 6-9 October 2009 in Mugla, Turkey in the course of collaborative organization undertaken by Turkish Atomic Energy Authority, Mugla University and Sitki Kocman Foundation. This first volume of Proceedings Book contains 75 submitted presentations and 36 of them are full texts on applications of nuclear techniques.

  3. Proceedings of the international topical meeting on nuclear and hazardous waste management

    International Nuclear Information System (INIS)

    Anon.

    1988-01-01

    This book contains the proceedings of the 1988 International Topical Meeting on Nuclear and Hazardous Waste Management. Included are the following articles: Defense radioactive waste management: status and challenges, Secrets of successful siting legislation for low-level radioactive waste disposal facilities, A generic hazardous waste management training program, Status of industry standards for decommissioning of nuclear facilities

  4. Proceedings of the National Seminar on Research and Nuclear Devices Management

    International Nuclear Information System (INIS)

    Prayitno; Slamet Santosa; Darsono; Syarip; Agus Taftazani; Samin; Tri Mardji Atmono; Dwi Biyantoro; Herry Poernomo; Prajitno; Tjipto Sujitno; Gede Sutresna W; Djoko Slamet Pujorahardjo; Budi Setiawan; Bambang Siswanto; Endro Kismolo; Jumari

    2016-08-01

    The Proceedings of the National Seminar on Research and Nuclear Devices Management by Center for Accelerator Science and Technology in Yogyakarta with the theme of Universities and research and development institutions synergy in the development of basic science and nuclear technology held on Surakarta 9 August 2016. This seminar is an annual routine activities of Center for Accelerator Science and Technology for exchange research result among University and BATAN researcher for using nuclear technology. The proceeding consist of 3 article from keynotes’ speaker and 23 articles from BATAN participant as well as outside which have been indexed separately. (MPN)

  5. Proceedings of the meeting and scientific presentations on basic science research and nuclear technology

    International Nuclear Information System (INIS)

    Prayitno; Slamet Santosa; Darsono; Syarip; Agus Taftazani; Samin; Tri Mardji Atmono; Dwi Biyantoro; Herry Poernomo; Prajitno; Tjipto Sujitno; Gede Sutresna W; Djoko Slamet Pujorahardjo; Budi Setiawan; Bambang Siswanto; Endro Kismolo; Jumari

    2016-08-01

    The Proceedings of the Meeting and Scientific Presentations on Basic Science Research and Nuclear Technology by Center for Accelerator Science and Technology in Yogyakarta with the theme of Universities and research and development institutions synergy in the development of basic science and nuclear technology held on Surakarta 9 August 2016. This seminar is an annual routine activities of Center for Accelerator Science and Technology for exchange research result among University and BATAN researcher for using nuclear technology. The proceeding consist of 3 article from keynotes’ speaker and 37 articles from BATAN participant as well as outside which have been indexed separately. (MPN)

  6. Automated processing of nuclear materials accounting data

    International Nuclear Information System (INIS)

    Straka, J.; Pacak, P.; Moravec, J.

    1980-01-01

    An automated system was developed of nuclear materials accounting in Czechoslovakia. The system allows automating data processing including data storage. It comprises keeping records of inventories and material balance. In designing the system, the aim of the IAEA was taken into consideration, ie., building a unified information system interconnected with state-run systems of accounting and checking nuclear materials in the signatory countries of the non-proliferation treaty. The nuclear materials accounting programs were written in PL-1 and were tested at an EC 1040 computer at UJV Rez where also the routine data processing takes place. (B.S.)

  7. The Physical Protection of Nuclear Material and Nuclear Facilities

    International Nuclear Information System (INIS)

    1999-08-01

    Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international co-operation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and nuclear materials, particularly when such materials are transported across national frontiers

  8. The Physical Protection of Nuclear Material and Nuclear Facilities

    International Nuclear Information System (INIS)

    1999-06-01

    Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international co-operation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and nuclear materials, particularly when such materials are transported across national frontiers [es

  9. The Physical Protection of Nuclear Material and Nuclear Facilities

    International Nuclear Information System (INIS)

    1999-06-01

    Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international co-operation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and nuclear materials, particularly when such materials are transported across national frontiers

  10. 9th Australian conference on nuclear techniques of analysis. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    The proceedings contains extended abstracts of 58 presentations. Topics discussed include: nondestructive testing methods, their performance and utilization, ion implantation, physical radiation effects, surface and cluster science. refs., figs.

  11. 9th Australian conference on nuclear techniques of analysis. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The proceedings contains extended abstracts of 58 presentations. Topics discussed include: nondestructive testing methods, their performance and utilization, ion implantation, physical radiation effects, surface and cluster science. refs., figs.

  12. 9th Australian conference on nuclear techniques of analysis. Proceedings

    International Nuclear Information System (INIS)

    1996-01-01

    The proceedings contains extended abstracts of 58 presentations. Topics discussed include: nondestructive testing methods, their performance and utilization, ion implantation, physical radiation effects, surface and cluster science. refs., figs

  13. Nuclear battery materials and application of nuclear batteries

    International Nuclear Information System (INIS)

    Hao Shaochang; Lu Zhenming; Fu Xiaoming; Liang Tongxiang

    2006-01-01

    Nuclear battery has lots of advantages such as small volume, longevity, environal stability and so on, therefore, it was widely used in aerospace, deep-sea, polar region, heart pacemaker, micro-electromotor and other fields etc. The application of nuclear battery and the development of its materials promote each other. In this paper the development and the latest research progress of nuclear battery materials has been introduced from the view of radioisotope, electric energy conversion and encapsulation. And the current and potential applications of the nuclear battery are also summarized. (authors)

  14. Aims and methods of nuclear materials management

    International Nuclear Information System (INIS)

    Leven, D.; Schier, H.

    1979-05-01

    Whilst international safeguarding of fissile materials against abuse has been the subject of extensive debate, little public attention has so far been devoted to the internal security of these materials. All countries using nuclear energy for peaceful purposes have laid down appropriate regulations. In the Federal Republic of Germany safeguards are required, for instance, by the Atomic Energy Act, and are therefore a prerequisite for licensing. The aims and methods of national nuclear materials management are contrasted with viewpoints on international safeguards

  15. The physical protection of nuclear material

    International Nuclear Information System (INIS)

    1989-12-01

    A Technical Committee on Physical Protection of Nuclear Material met in April-May 1989 to advise on the need to update the recommendations contained in document INFCIRC/225/Rev.1 and on any changes considered to be necessary. The Technical Committee indicated a number of such changes, reflecting mainly: the international consensus established in respect of the Convention on the Physical Protection of Nuclear Material; the experience gained since 1977; and a wish to give equal treatment to protection against the theft of nuclear material and protection against the sabotage of nuclear facilities. The recommendations presented in this IAEA document reflect a broad consensus among Member States on the requirements which should be met by systems for the physical protection of nuclear materials and facilities. 1 tab

  16. The 4th Nuclear Science and Technology Conference. Proceedings

    International Nuclear Information System (INIS)

    1992-01-01

    This conference includes papers on a broad range of applications for nuclear technologies. Some of the topics covered are the electron beam and its applications, nuclear applications in industry, nuclear power in Japan, radiobiology for the environment, significant developments in nuclear medicine and nuclear applications in agriculture

  17. International conference on innovative technologies for nuclear fuel cycles and nuclear power. Unedited proceedings

    International Nuclear Information System (INIS)

    2004-01-01

    Nuclear power is a significant contributor to the global supply of electricity, and continues to be the major source that can provide electricity on a large scale with a comparatively minimal impact on the environment. But it is evident that, despite decades of experience with this technology, nuclear power today remains mainly in a holding position, with its future somewhat uncertain primarily due to concerns related to waste, safety and security. One of the most important factors that would influence future nuclear growth is the innovation in reactor and fuel cycle technologies to successfully maximize the benefits of nuclear power while minimizing the associated concerns. The main objectives of the Conference were to facilitate exchange of information between senior experts and policy makers from Member States and international organizations on important aspects of the development of innovative technologies for future generations of nuclear power reactors and fuel cycles; to create an understanding of the social, environmental and economic conditions that would facilitate innovative and sustainable nuclear technologies; and to identify opportunities for collaborative work between Member States and international organizations and programmes. All relevant aspects of innovative technologies for nuclear fuel cycles and nuclear power were discussed in an open, frank and objective manner. These proceedings contain a summary of the results of the conference, invited and contributed papers, and summaries of panel discussions. No large increase in the use of nuclear energy is foreseen in the near and medium term, but is likely in the long term if developing country per-capita electricity consumption reaches that of the developed world. The nuclear sector including regulators view an increased use of nuclear energy as the solution for global sustainable energy needs considering that significant reductions in CO 2 emissions would be required. Although the current nuclear

  18. Control assembly materials for water reactors: Experience, performance and perspectives. Proceedings of a technical committee meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-02-01

    materials science and materials engineering of control assembly materials, the 1993 meeting and the current one are helping to fill a gap in the information exchange opportunities in this important branch of nuclear research and development. The second TCM, entitled Control Assembly Materials for Water Reactors: Experience, Performance and Perspectives, was attended by thirty-one participants from fourteen countries, nineteen papers were presented and are reproduced in this proceedings together with a summary of the meeting.

  19. Control assembly materials for water reactors: Experience, performance and perspectives. Proceedings of a technical committee meeting

    International Nuclear Information System (INIS)

    2000-02-01

    materials science and materials engineering of control assembly materials, the 1993 meeting and the current one are helping to fill a gap in the information exchange opportunities in this important branch of nuclear research and development. The second TCM, entitled Control Assembly Materials for Water Reactors: Experience, Performance and Perspectives, was attended by thirty-one participants from fourteen countries, nineteen papers were presented and are reproduced in this proceedings together with a summary of the meeting

  20. Integrated Global Nuclear Materials Management Preliminary Concepts

    International Nuclear Information System (INIS)

    Jones, E; Dreicer, M.

    2006-01-01

    The world is at a turning point, moving away from the Cold War nuclear legacy towards a future global nuclear enterprise; and this presents a transformational challenge for nuclear materials management. Achieving safety and security during this transition is complicated by the diversified spectrum of threat 'players' that has greatly impacted nonproliferation, counterterrorism, and homeland security requirements. Rogue states and non-state actors no longer need self-contained national nuclear expertise, materials, and equipment due to availability from various sources in the nuclear market, thereby reducing the time, effort and cost for acquiring a nuclear weapon (i.e., manifestations of latency). The terrorist threat has changed the nature of military and national security requirements to protect these materials. An Integrated Global Nuclear Materials Management (IGNMM) approach would address the existing legacy nuclear materials and the evolution towards a nuclear energy future, while strengthening a regime to prevent nuclear weapon proliferation. In this paper, some preliminary concepts and studies of IGNMM will be presented. A systematic analysis of nuclear materials, activities, and controls can lead to a tractable, integrated global nuclear materials management architecture that can help remediate the past and manage the future. A systems approach is best suited to achieve multi-dimensional and interdependent solutions, including comprehensive, end-to-end capabilities; coordinated diverse elements for enhanced functionality with economy; and translation of goals/objectives or standards into locally optimized solutions. A risk-informed basis is excellent for evaluating system alternatives and performances, and it is especially appropriate for the security arena. Risk management strategies--such as defense-in-depth, diversity, and control quality--help to weave together various technologies and practices into a strong and robust security fabric. Effective

  1. Croatian National System of Nuclear Materials Control

    International Nuclear Information System (INIS)

    Biscan, R.

    1998-01-01

    In the process of economic and technological development of Croatia by using or introducing nuclear power or in the case of international co-operation in the field of peaceful nuclear activities, including international exchange of nuclear material, Croatia should establish and implement National System of Nuclear Materials Control. Croatian National System of accounting for and control of all nuclear material will be subjected to safeguards under requirements of Agreement and Additional Protocol between the Republic of Croatia and the International Atomic Energy Agency (IAEA) for the Application of Safeguards in Connection with the Treaty on the Non-Proliferation of Nuclear Weapons (NPT). The decision by NPT parties at the 1995 NPT Review and Extension Conference to endorse the Fullscope IAEA Safeguards Standard (FSS) as a necessary precondition of nuclear supply means that states are obliged to ensure that the recipient country has a FSS agreement in place before any nuclear transfer can take place (Ref. 1). The FSS standard of nuclear supply is a central element of the Nuclear Suppliers Group (NSG) Guidelines which the NSG adopted in 1992 and should be applied to members and non-members of the NSG. The FSS standard of nuclear supply in general allows for NPT parties or countries which have undertaken the same obligations through other treaty arrangements, to receive favourable treatment in nuclear supply arrangements. However, the Iraqi experience demonstrate that trade in nuclear and dual-use items, if not properly monitored, can contribute to a nuclear weapons program in countries acting contrary to their non-proliferation obligation. Multilateral nuclear export control mechanisms, including the FSS supply standard, provide the basis for co-ordination and standardisation of export control measures. (author)

  2. Hirschegg '03: Nuclear structure and dynamics at the limits. Proceedings

    International Nuclear Information System (INIS)

    Feldmeier, H.; Knoll, J.; Noerenberg, W.; Wambach, J.

    2003-01-01

    The following topics were dealt with: Nuclear structure ans symmetries, nuclei near the drip line, halo nuclei and nuclear resonances, superheavy elements and fission, fragmentation and multifragmentation, nuclear astrophysics. (HSI)

  3. Special conditions for the application of coating materials in nuclear power plants

    International Nuclear Information System (INIS)

    Boetius, I.

    1980-01-01

    Proceeding from the special conditions for the application of coating materials in nuclear power plants the following factors influencing the decontamination of surface coatings are discussed from the point of view of radiation protection: abrasion resistance, waterproofness, mechanical and adhesion strength, and permeability. For practical use it is recommended to test the surface tightness of coatings with radiation-exposed specimens

  4. Supplier responsibility for nuclear material quality

    International Nuclear Information System (INIS)

    Stuart, P.S.; Dohna, A.E.

    1976-01-01

    Nuclear materials must be delivered by either the manufacturer or the distributor with objective, documented evidence that the material was manufactured, inspected, and tested by proven techniques performed by qualified personnel working to documented procedures. Measurement devices used for acceptance must be of proven accuracy. The material and all records must be identified for positive traceability as part of the quality history of the nuclear components, system, or structure in which the material was used. In conclusion, the nuclear material supplier must join the fabricator, the installer, and the user in effective implementation of the total systems approach to the application of quality assurance principles to all phases of procurement, fabrication, installation, and use of the safety-related components, systems, and structures in a nuclear power plant

  5. Nuclear Measurements, Evaluations and Applications - NEMEA-6. Workshop Proceedings

    International Nuclear Information System (INIS)

    2011-01-01

    NEMEA-6 brought together nuclear scientists from the new member states that joined the European Union since 2000, scientists from the 'old' member states and colleagues from Russia and Israel. About 30 papers were presented. Topics addressed during the workshop involved nuclear data needs and impact, nuclear data validation and benchmarks, the ANDES - Accurate Nuclear Data for nuclear Energy Sustainability project, detectors and facilities, and measurements of nuclear data

  6. Proceedings of the KNS spring meeting

    International Nuclear Information System (INIS)

    2004-01-01

    This proceedings contains articles of 2004 spring meeting of the Korean Nuclear Society. It was held on May 27-28, 2004 in Gyeongju, Korea. This proceedings is comprised of 10 sessions. The main subject titles of session are as follows: reactor physics and nuclear reactor design, thermodynamics and fluid flow, reactor operation and control, reactor safety, reactor fuels and nuclear materials, fuel cycle and waste management, radiation protection, nuclear fusion and laser technology, fuel cycle and waste management, nuclear fuel and nuclear materials, radiation protection, radiation application, life time management and decontamination, nuclear structure, nuclear beam application and nuclear fusion, nuclear policy. (Yi, J. H.)

  7. Proceedings of the KNS spring meeting

    International Nuclear Information System (INIS)

    2003-01-01

    This proceedings contains articles of 2003 spring meeting of the Korean Nuclear Society. It was held on May 29-30, 2003 in Gyeongju, Korea. This proceedings is comprised of 12 sessions. The main subject titles of session are as follows: reactor physics and nuclear reactor design, reactor operation and control, thermodynamics and fluid flow, reactor safety, reactor fuels and nuclear materials, fuel cycle and waste management, radiation protection, nuclear fusion and laser technology, fuel cycle and waste management, nuclear fuel and nuclear materials, radiation protection, radiation application, life time management and decontamination, nuclear structure, nuclear physics and nuclear fusion, nuclear policy. (Yi, J. H.)

  8. Proceedings of 26. annual academic conference of China Chemical Society--modern nuclear chemistry and radiochemistry

    International Nuclear Information System (INIS)

    2008-08-01

    26. annual academic conference of China Chemical Society was held in Tianjing, 13-16 July, 2008. This proceedings is about modern nuclear chemistry and radiochemistry, the contents include: new elements and new nuclides; advanced nuclear chemistry; radiochemistry and national security; new radiopharmaceutical chemistry; modern radiological analytical chemistry and large scientific facilities; radiological environmental chemistry and nuclear radioactive waste; actinide chemistry and transactinide chemistry; radiochemistry and cross discipline, etc.

  9. International meeting 'Selected topics on nuclear methods for non-nuclear applications'. Proceedings

    International Nuclear Information System (INIS)

    Stoyanov, Ch.

    2007-01-01

    The volume includes the presentations given on the International Meeting 'Selected Topics on Nuclear Methods for Non-nuclear Applications'. The meeting was organized by the Project CECOA. The Project 'CEnter for COoerative Activities' (CECOA) of the Institute for Nuclear Research and Nuclear Energy (INRNE) of Bulgarian Academy of Sciences is part of the Program 'Creating of Infrastructure' of Bulgarian Ministry of Science and Education. The CECOA-project unifies the groups of INRNE doing research in the field of nuclear methods. Four Laboratories of INRNE are members of CECOA-project: Moessbauer Spectroscopy and Low Radioactivity Measurements, High-Resolution Gamma-Spectroscopy, Neutron Methods in Condensed Matter, Neutron Optics and Structure Analysis. Taking into account the leading role of education on nuclear physics the Project includes program devoted to the training on nuclear physics. The presented volume contains 23 contributed papers. The contributions are separated in 6 sections. The section 'Nano technology' includes 5 papers. The activity in this field within the Project reveals the collaboration with other Institutes of Bulgarian Academy of Sciences as well as large international contacts. The section 'Radioecology and Radioactive Waste' is two fold. Part of the contributions of the section manifests the connection of the CECOA with small enterprises. The contacts are on the level of common projects concerning the investigations, remediation and release of radioactively contaminated terrain, soils, water, buildings and materials around the former uranium processing industry. Another part of the section is devoted to the application of nuclear methods to the treatment of radioactive waste produced by nuclear power stations. The section 'Neutron Physics' reveals the activity within the Project connected with the study of new materials using polarized neutrons and neutron diffraction methods. The section 'Nuclear Physics' is an introduction to some

  10. Proceedings of the 29th annual conference of the Canadian Nuclear Association and 10th annual conference of the Canadian Nuclear Society. V. 1-3

    International Nuclear Information System (INIS)

    Harvey, M.; Fehrenbach, P.J.

    1989-01-01

    The symposium was designed to highlight how the technical information for nuclear energy came to Canada, the effect this information had in Canada in the fields of Physics, Chemistry, Medicine and Nuclear Power. Volume 1 is the combined proceedings of the Canadian Nuclear Association twenty-ninth annual conference and the Canadian Nuclear Society tenth annual conference. Volume 2 is the proceedings of the Canadian Nuclear Association twenty-ninth annual conference, and volume 3 is the proceedings of the Canadian Nuclear Society tenth annual conference

  11. Proceedings of the 29th annual conference of the Canadian Nuclear Association and 10th annual conference of the Canadian Nuclear Society. V. 1-3

    Energy Technology Data Exchange (ETDEWEB)

    Harvey, M; Fehrenbach, P J [eds.

    1990-12-31

    The symposium was designed to highlight how the technical information for nuclear energy came to Canada, the effect this information had in Canada in the fields of Physics, Chemistry, Medicine and Nuclear Power. Volume 1 is the combined proceedings of the Canadian Nuclear Association twenty-ninth annual conference and the Canadian Nuclear Society tenth annual conference. Volume 2 is the proceedings of the Canadian Nuclear Association twenty-ninth annual conference, and volume 3 is the proceedings of the Canadian Nuclear Society tenth annual conference.

  12. Nuclear materials stewardship: Our enduring mission

    International Nuclear Information System (INIS)

    Isaacs, T.H.

    1998-01-01

    The US Department of Energy (DOE) and its predecessors have handled a remarkably wide variety of nuclear materials over the past 50 yr. Two fundamental changes have occurred that shape the current landscape regarding nuclear materials. If one recognizes the implications and opportunities, one sees that the stewardship of nuclear materials will be a fundamental and important job of the DOE for the foreseeable future. The first change--the breakup of the Soviet Union and the resulting end to the nuclear arms race--altered US objectives. Previously, the focus was on materials production, weapon design, nuclear testing, and stockpile enhancements. Now the attention is on dismantlement of weapons, excess special nuclear material inventories, accompanying increased concern over the protection afforded to such materials; new arms control measures; and importantly, maintenance of the safety and reliability of the remaining arsenal without testing. The second change was the raised consciousness and sense of responsibility for dealing with the environmental legacies of past nuclear arms programs. Recognition of the need to clean up radioactive contamination, manage the wastes, conduct current operations responsibly, and restore the environment have led to the establishment of what is now the largest program in the DOE. Two additional features add to the challenge and drive the need for recognition of nuclear materials stewardship as a fundamental, enduring, and compelling mission of the DOE. The first is the extraordinary time frames. No matter what the future of nuclear weapons and no matter what the future of nuclear power, the DOE will be responsible for most of the country's nuclear materials and wastes for generations. Even if the Yucca Mountain program is successful and on schedule, it will last more than 100 yr. Second, the use, management, and disposition of nuclear materials and wastes affect a variety of nationally important and diverse objectives, from national

  13. Control of nuclear materials and materials in Argentina

    International Nuclear Information System (INIS)

    Arbor G, A.; Fernandes M, S.

    1988-01-01

    A general view about the safeguards activities in Argentina is presented. The national system of accounting for and control of nuclear materials is described. The safeguards agreement signed by Argentina are presented. (E.G.) [pt

  14. Global nuclear material flow/control model

    International Nuclear Information System (INIS)

    Dreicer, J.S.; Rutherford, D.S.; Fasel, P.K.; Riese, J.M.

    1997-01-01

    This is the final report of a two-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The nuclear danger can be reduced by a system for global management, protection, control, and accounting as part of an international regime for nuclear materials. The development of an international fissile material management and control regime requires conceptual research supported by an analytical and modeling tool which treats the nuclear fuel cycle as a complete system. The prototype model developed visually represents the fundamental data, information, and capabilities related to the nuclear fuel cycle in a framework supportive of national or an international perspective. This includes an assessment of the global distribution of military and civilian fissile material inventories, a representation of the proliferation pertinent physical processes, facility specific geographic identification, and the capability to estimate resource requirements for the management and control of nuclear material. The model establishes the foundation for evaluating the global production, disposition, and safeguards and security requirements for fissile nuclear material and supports the development of other pertinent algorithmic capabilities necessary to undertake further global nuclear material related studies

  15. Proceedings of the 2004 international congress on advances in nuclear power plants - ICAPP'04

    International Nuclear Information System (INIS)

    2004-01-01

    The 2004 International Congress on Advances in Nuclear Power Plants (ICAPP'04) provides a forum for the industry to exchange the latest ideas and research findings on nuclear plants from all perspectives. This conference builds on the success of last year's meeting held in Cordoba, Spain, and on the 2002 inaugural meeting held in Hollywood, Florida. Because of the hard work of many volunteers from around the world, ICAPP'04 has been successful in achieving its goal. More than 325 invited and contributed papers/presentations are part of this ICAPP. There are 5 invited plenary sessions and 70 technical sessions with contributed papers. The ICAPP'04 Proceedings contain almost 275 papers prepared by authors from 25 countries covering topics related to advances in nuclear power plant technology. The program by technical track deals with: 1 - Water-Cooled Reactor Programs and Issues (Status of All New Water-Cooled Reactor Programs; Advanced PWRs: Developmental Stage I; Advanced PWRs: Developmental Stage II; Advanced PWRs: Basic Design Stage; Advanced BWRs; Economics, Regulation, Licensing, and Construction; AP1000); 2 - High Temperature Gas Cooled Reactors (Pebble Bed Modular Reactors; Very High Temperature Reactors; HTR Fuels and Materials; Innovative HTRs and Fuel Cycles); 3 - Long Term Reactor Programs and Strategies (Supercritical Pressure Water Reactors; Lead-Alloy Fast Reactors; Sodium and Gas Fast Reactors; Status of Advanced Reactor Programs; Non-classical Reactor Concepts); 4 - Operation, Performance, and Reliability Management (Information Technology Effect on Plant Operation; Operation, Maintenance and Reliability; Improving Performance and Reducing O and M Costs; Plant Modernization and Retrofits); 5 - Plant Safety Assessment and Regulatory Issues (LOCA and non-LOCA Analysis Methodologies; LOCA and non-LOCA Plant Analyses; In-Vessel Retention; Containment Performance and Hydrogen Control; Advances in Severe Accident Analysis; Advances in Severe Accident

  16. Proceedings of the Canadian Nuclear Association 25th annual conference

    International Nuclear Information System (INIS)

    1985-01-01

    The twenty addresses presented in this volume celebrate the 25th anniversary of the Canadian Nuclear Association. They reflect upon evolving world electricity patterns, the nuclear power option, Canada's position as a supplier of uranium and nuclear technology, the future of the nuclear industry in Canada, and the position of the industry in the United States and Britain

  17. Regulation on control of nuclear fuel materials

    International Nuclear Information System (INIS)

    Ikeda, Kaname

    1976-01-01

    Some comment is made on the present laws and the future course of consolidating the regulation of nuclear fuel materials. The first part gives the definitions of the nuclear fuel materials in the laws. The second part deals with the classification and regulation in material handling. Refinement undertaking, fabrication undertaking, reprocessing undertaking, the permission of the government to use the materials, the permission of the government to use the materials under international control, the restriction of transfer and receipt, the reporting, and the safeguard measures are commented. The third part deals with the strengthening of regulation. The nuclear fuel safety deliberation special committee will be established at some opportunity of revising the ordinance. The nuclear material safeguard special committee has been established in the Atomic Energy Commission. The last part deals with the future course of legal consolidation. The safety control will be strengthened. The early investigation of waste handling is necessary, because low level solid wastes are accumulating at each establishment. The law for transporting nuclear materials must be consolidated as early as possible to correspond to foreign transportation laws. Physical protection is awaiting the conclusions of the nuclear fuel safeguard special committee. The control and information systems for the safeguard measures must be consolidated in the laws. (Iwakiri, K.)

  18. Automated accounting systems for nuclear materials

    International Nuclear Information System (INIS)

    Erkkila, B.

    1994-01-01

    History of the development of nuclear materials accounting systems in USA and their purposes are considered. Many present accounting systems are based on mainframe computers with multiple terminal access. Problems of future improvement accounting systems are discussed

  19. The Physical Protection of Nuclear Material

    International Nuclear Information System (INIS)

    1993-01-01

    Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers

  20. The Physical Protection of Nuclear Material

    International Nuclear Information System (INIS)

    1993-09-01

    Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers [es

  1. The Physical Protection of Nuclear Material

    International Nuclear Information System (INIS)

    1993-09-01

    Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers [fr

  2. Transport packages for nuclear material and waste

    International Nuclear Information System (INIS)

    1997-01-01

    The regulations and responsibilities concerning the transport packages of nuclear materials and waste are given in the guide. The approval procedure, control of manufacturing, commissioning of the packaging and the control of use are specified. (13 refs.)

  3. List of Nuclear Materials Licensing Actions Received

    Data.gov (United States)

    Nuclear Regulatory Commission — A catalog of all Materials Licensing Actions received for review. The catalog lists the name of the entity submitting the license application, their city and state,...

  4. The Physical Protection of Nuclear Material

    International Nuclear Information System (INIS)

    1993-09-01

    Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers

  5. 10 CFR 74.41 - Nuclear material control and accounting for special nuclear material of moderate strategic...

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Nuclear material control and accounting for special nuclear material of moderate strategic significance. 74.41 Section 74.41 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) MATERIAL CONTROL AND ACCOUNTING OF SPECIAL NUCLEAR MATERIAL Special Nuclear Material...

  6. Study of nuclear environment and material strategy

    International Nuclear Information System (INIS)

    Kamei, Takashi

    2011-01-01

    There is a concern about the environmental hazard caused by radioactive materials coming with the expansion of nuclear power and even by renewable energies, which are used as countermeasures against global warming to construct a sustainable society. A concept to internalize the pollution caused by radioactive materials, which are directly or indirectly related to nuclear power, to economical activities by adopting externality is proposed. Energy and industrial productions are strongly related to the supply of material. Therefore material flow is also part of this internalization concept. The concept is named 'NEMS (Nuclear Environment and Material Strategy)'. Fission products and transuranic isotopes from nuclear power such as plutonium are considered in this concept. Thorium, which comes from the material flow of rare-earth production to support the elaboration of renewable energies including electric vehicles on the consumer side, is considered as an externality of the non-nuclear power field. Fission products contain some rare-earth materials. Thus, these rare-earth materials, which are extracted by the advanced ORIENT (Optimization by Recycling Instructive Elements) cycle, are internalized as rare-earth supplier in economy. However, the supply quantity is limited. Therefore rare-earth production itself is still needed. The externality of rare-earth production is thorium and is internalized by using it as nuclear fuel. In this case, the demand of thorium is still small within these few decades compared to the production of thorium as byproduct of the rare-earth production. A thorium energy bank (The Bank) is advanced to regulate the storage of the excess amount of thorium inside of an international framework in order to prevent environmental hazard resulting from the illegal disposal of thorium. In this paper, the material flows of thorium and rare-earth are outlined. Their material balance are demonstrated based on the prediction of rare-earth mining and an

  7. Powder metallurgical high performance materials. Proceedings. Volume 2: P/M hard materials

    Energy Technology Data Exchange (ETDEWEB)

    Kneringer, G; Roedhammer, P; Wildner, H [eds.

    2001-07-01

    The proceedings of these seminars form an impressive chronicle of the continued progress in the understanding of refractory metals and cemented carbides and in their manufacture and application. There the ingenuity and assiduous work of thousands of scientists and engineers striving for progress in the field of powder metallurgy is documented in more than 2000 contributions covering some 30000 pages. The 15{sup th} Plansee Seminar was convened under the general theme 'Powder Metallurgical High Performance Materials'. Under this broadened perspective the seminar will strive to look beyond the refractory metals and cemented carbides, which remain at its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. (author)

  8. Powder metallurgical high performance materials. Proceedings. Volume 2: P/M hard materials

    International Nuclear Information System (INIS)

    Kneringer, G.; Roedhammer, P.; Wildner, H.

    2001-01-01

    The proceedings of these seminars form an impressive chronicle of the continued progress in the understanding of refractory metals and cemented carbides and in their manufacture and application. There the ingenuity and assiduous work of thousands of scientists and engineers striving for progress in the field of powder metallurgy is documented in more than 2000 contributions covering some 30000 pages. The 15 th Plansee Seminar was convened under the general theme 'Powder Metallurgical High Performance Materials'. Under this broadened perspective the seminar will strive to look beyond the refractory metals and cemented carbides, which remain at its focus, to novel classes of materials, such as intermetallic compounds, with potential for high temperature applications. (author)

  9. Reactor Structure Materials: Nuclear Fuel

    International Nuclear Information System (INIS)

    Sannen, L.; Verwerft, M.

    2000-01-01

    Progress and achievements in 1999 in SCK-CEN's programme on applied and fundamental nuclear fuel research in 1999 are reported. Particular emphasis is on thermochemical fuel research, the modelling of fission gas release in LWR fuel as well as on integral experiments

  10. Overview of nuclear materials transportation

    International Nuclear Information System (INIS)

    Grella, A.W.

    1986-01-01

    This presentation is an overview of transportation as it relates to one specific type of material, low specific activity (LSA) material. It is the predominant type of material that fits into the low-level waste category. An attempt is made to discuss how LSA is regulated, setting forth the requirements. First the general scheme of regulations are reviewed. In addition future changes in the regulations which will affect transportation of LSA materials and, which quite likely, will have an impact on R and D needs in this area are presented

  11. Estimation methods for special nuclear materials holdup

    International Nuclear Information System (INIS)

    Pillay, K.K.S.; Picard, R.R.

    1984-01-01

    The potential value of statistical models for the estimation of residual inventories of special nuclear materials was examined using holdup data from processing facilities and through controlled experiments. Although the measurement of hidden inventories of special nuclear materials in large facilities is a challenging task, reliable estimates of these inventories can be developed through a combination of good measurements and the use of statistical models. 7 references, 5 figures

  12. Fundamentals of materials accounting for nuclear safeguards

    Energy Technology Data Exchange (ETDEWEB)

    Pillay, K.K.S. (comp.)

    1989-04-01

    Materials accounting is essential to providing the necessary assurance for verifying the effectiveness of a safeguards system. The use of measurements, analyses, records, and reports to maintain knowledge of the quantities of nuclear material present in a defined area of a facility and the use of physical inventories and materials balances to verify the presence of special nuclear materials are collectively known as materials accounting for nuclear safeguards. This manual, prepared as part of the resource materials for the Safeguards Technology Training Program of the US Department of Energy, addresses fundamental aspects of materials accounting, enriching and complementing them with the first-hand experiences of authors from varied disciplines. The topics range from highly technical subjects to site-specific system designs and policy discussions. This collection of papers is prepared by more than 25 professionals from the nuclear safeguards field. Representing research institutions, industries, and regulatory agencies, the authors create a unique resource for the annual course titled ''Materials Accounting for Nuclear Safeguards,'' which is offered at the Los Alamos National Laboratory.

  13. Proceedings of the water chemistry and materials performance conference

    Energy Technology Data Exchange (ETDEWEB)

    Barber, D [ed.; Atomic Energy of Canada Ltd., Sheridan Park, ON (Canada). CANDU Operations

    1987-12-31

    The proceedings contain 11 papers dealing with primary and secondary side water chemistry in CANDU reactors, with the associated problems of activity transport and steam generator corrosion, and also with the use of decontaminating solutions. The individual papers have been abstracted separately.

  14. Proceedings of the water chemistry and materials performance conference

    International Nuclear Information System (INIS)

    Barber, D.

    1986-01-01

    The proceedings contain 11 papers dealing with primary and secondary side water chemistry in CANDU reactors, with the associated problems of activity transport and steam generator corrosion, and also with the use of decontaminating solutions. The individual papers have been abstracted separately

  15. Resources of nuclear fuels and materials

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, K [Tokyo Inst. of Tech. (Japan); Kamiyama, Teiji; Hayashi, S; Hida, Noboru; Okano, T

    1974-11-01

    In this explanatory article, data on the world resources of nuclear fuels and materials, their production, and the present state of utilization are presented by specialists in varied fields. Main materials taken up are uranium, thorium, beryllium, zirconium, niobium, rare earth elements, graphite, and materials for nuclear fusion (heavy hydrogen and tritium). World reserves and annual production of these materials listed in a number of tables are cited from statistics of the period 1970-1973 or given by estimation. These data may be used as valuable numerical data for various projects and problems of atomic power industries.

  16. Nuclear material control in the United States

    International Nuclear Information System (INIS)

    Jaeger, C.; Waddoups, I.

    1995-01-01

    The Department of Energy has defined a safeguards system to be an integrated system of physical protection, material accounting and material control subsystems designed to deter, prevent, detect, and respond to unauthorized possession, use, or sabotage of SNM. In practice, safeguards involve the development and application of techniques and procedures dealing with the establishment and continued maintenance of a system of activities. The system must also include administrative controls and surveillance to assure that the procedures and techniques of the system are effective and are being carried out. The control of nuclear material is critical to the safeguarding of nuclear materials within the United States. The U.S. Department of Energy includes as part of material control four functional performance areas. They include access controls, material surveillance, material containment and detection/assessment. This paper will address not only these areas but also the relationship between material control and other safeguards and security functions

  17. Considerations for sampling nuclear materials for SNM accounting measurements. Special nuclear material accountability report

    International Nuclear Information System (INIS)

    Brouns, R.J.; Roberts, F.P.; Upson, U.L.

    1978-05-01

    This report presents principles and guidelines for sampling nuclear materials to measure chemical and isotopic content of the material. Development of sampling plans and procedures that maintain the random and systematic errors of sampling within acceptable limits for SNM(Special Nuclear Materials) accounting purposes are emphasized

  18. Overview moderator material for nuclear reactor components

    International Nuclear Information System (INIS)

    Mairing Manutu Pongtuluran; Hendra Prihatnadi

    2009-01-01

    In order for a reactor design is considered acceptable absolute technical requirement is fulfilled because the most important part of a reactor design. Safety considerations emphasis on the handling of radioactive substances emitted during the operation of a reactor and radioactive waste handling. Moderator material is a layer that interacts directly with neutrons split the nuclear fuel that will lead to changes in physical properties, nuclear properties, mechanical properties and chemical properties. Reviews moderator of this time is of the types of moderator is often used to meet the requirements as nuclear material. (author)

  19. Proceedings of the 4. General Congress on Nuclear Energy. v. 1

    International Nuclear Information System (INIS)

    1992-01-01

    The first volume of the 4. General Congress on Nuclear Energy presents works about transient and accident analysis; thermohydraulics; radioisotopes uses; fuel cycle; shield; material technology; nuclear installation construction and reactor and nuclear physics. (C.G.C.)

  20. The proceedings of the 14th national symposium on atomic physics and nuclear physics and the 7th annual meeting on modern physics

    International Nuclear Information System (INIS)

    2002-01-01

    It is the proceedings of the 14th national symposium on atomic physics and nuclear physics and the 7th annual meeting on modern physics. 27 theses are collected in these proceedings. Many of them are related with nuclear physics

  1. New materials in nuclear fusion reactors

    International Nuclear Information System (INIS)

    Iwata, Shuichi

    1988-01-01

    In the autumn of 1987, the critical condition was attained in the JET in Europe and Japanese JT-60, thus the first subject in the physical verification of nuclear fusion reactors was resolved, and the challenge to the next attainment of self ignition condition started. As the development process of nuclear fusion reactors, there are the steps of engineering, economical and social verifications after this physical verification, and in respective steps, there are the critical problems related to materials, therefore the development of new materials must be advanced. The condition of using nuclear fusion reactors is characterized by high fluence, high thermal flux and strong magnetic field, and under such extreme condition, the microscopic structures of materials change, and they behave much differently from usual case. The subjects of material development for nuclear fusion reactors, the material data base being built up, the materials for facing plasma and high thermal flux, first walls, blanket structures, electric insulators and others are described. The serious effect of irradiation and the rate of defect inducement must be taken in consideration in the structural materials for nuclear fusion reactors. (Kako, I.)

  2. Material degradation - a nuclear utility's view

    International Nuclear Information System (INIS)

    Spekkens, P.

    2007-01-01

    Degradation of nuclear plant materials has been responsible for major costs and unit outage time. As such, nuclear utilities are important end users of the information produced by R and D on material degradation. This plenary describes the significance of material degradation for the nuclear utilities, and how utilities use information about material degradation in their short, medium and long term planning activities. Utilities invest in R and D programs to assist them in their business objective of operating safely, reliably and cost competitively. Material degradation impacts all three of these business drivers. Utilities make decisions on life cycle planning, unit refurbishment and 'new build' projects on the basis of their understanding of the behaviour of a variety of materials in a broad range of environments. The R and D being carried out today will determine the future business success of the nuclear utilities. The R and D program needs to be broadly based to include a range of materials, environments and time-frames, particularly any new materials proposed for use in new units. The R and D community needs to help the utility managers make choices that will result in an optimized materials R and D program

  3. International safeguards: Accounting for nuclear materials

    Energy Technology Data Exchange (ETDEWEB)

    Fishbone, L.G.

    1988-09-28

    Nuclear safeguards applied by the International Atomic Energy Agency (IAEA) are one element of the non-proliferation regime'', the collection of measures whose aim is to forestall the spread of nuclear weapons to countries that do not already possess them. Safeguards verifications provide evidence that nuclear materials in peaceful use for nuclear-power production are properly accounted for. Though carried out in cooperation with nuclear facility operators, the verifications can provide assurance because they are designed with the capability to detect diversion, should it occur. Traditional safeguards verification measures conducted by inspectors of the IAEA include book auditing; counting and identifying containers of nuclear material; measuring nuclear material; photographic and video surveillance; and sealing. Novel approaches to achieve greater efficiency and effectiveness in safeguards verifications are under investigation as the number and complexity of nuclear facilities grow. These include the zone approach, which entails carrying out verifications for groups of facilities collectively, and randomization approach, which entails carrying out entire inspection visits some fraction of the time on a random basis. Both approaches show promise in particular situations, but, like traditional measures, must be tested to ensure their practical utility. These approaches are covered on this report. 15 refs., 16 figs., 3 tabs.

  4. International safeguards: Accounting for nuclear materials

    International Nuclear Information System (INIS)

    Fishbone, L.G.

    1988-01-01

    Nuclear safeguards applied by the International Atomic Energy Agency (IAEA) are one element of the ''non-proliferation regime'', the collection of measures whose aim is to forestall the spread of nuclear weapons to countries that do not already possess them. Safeguards verifications provide evidence that nuclear materials in peaceful use for nuclear-power production are properly accounted for. Though carried out in cooperation with nuclear facility operators, the verifications can provide assurance because they are designed with the capability to detect diversion, should it occur. Traditional safeguards verification measures conducted by inspectors of the IAEA include book auditing; counting and identifying containers of nuclear material; measuring nuclear material; photographic and video surveillance; and sealing. Novel approaches to achieve greater efficiency and effectiveness in safeguards verifications are under investigation as the number and complexity of nuclear facilities grow. These include the zone approach, which entails carrying out verifications for groups of facilities collectively, and randomization approach, which entails carrying out entire inspection visits some fraction of the time on a random basis. Both approaches show promise in particular situations, but, like traditional measures, must be tested to ensure their practical utility. These approaches are covered on this report. 15 refs., 16 figs., 3 tabs

  5. Student Scientific Conference - Nuclear Physics, 2008. Proceedings of contributions

    International Nuclear Information System (INIS)

    2008-01-01

    The conference included the following sections: (i) Biophysics and medicine physics; (ii) Experimental physics and theoretical physics; (iii) Nuclear physics; (iv) Informatics; (v) Mathematics; (vi) Theoretical graphics. Contributions of nuclear physics have been inputted to INIS.

  6. Proceedings of the 10. Workshop on Nuclear Physics in Brazil

    International Nuclear Information System (INIS)

    1987-01-01

    Theoretical and experimental studies on Nuclear Physics are presented. Nuclei structures, nuclear reaction cross sections, collision phenomena between particles at several energy ranges and radiation effects on solids and liquids are analysed. (M.C.K.) [pt

  7. Proceedings of the 2012 symposium on nuclear data

    International Nuclear Information System (INIS)

    Nakajima, Ken; Hori, Jun-ichi

    2013-10-01

    The 2012 symposium on nuclear data organized by the Nuclear Data Division of Atomic Energy Society of Japan (AESJ) and Research Reactor Institute, Kyoto University (KURRI) was held at Kumatori, KURRI on Nov. 15th and 16th, 2012 in cooperation with Nuclear Science and Engineering Directorate of Japan Atomic Energy Agency. The symposium was devoted for presentations and discussions on the four topics: 'Nuclear Power after Fukushima Nuclear Plant Accident', 'Application of Nuclear Data', 'How Should We Deal with Covariances of Nuclear Data?' and 'Validation of JENDL-4.0 and Future', as well as poster sessions on various research fields. Tutorials on neutron resonance capture and transmission analysis, international trend of nuclear data research were also given in the symposium. Talks as well as posters presented at the symposium aroused lively discussions among approximately 83 participants. This report consists of total 35 papers including 13 oral presentations and 22 poster presentations. (author)

  8. Nuclear Space Power Systems Materials Requirements

    International Nuclear Information System (INIS)

    Buckman, R.W. Jr.

    2004-01-01

    High specific energy is required for space nuclear power systems. This generally means high operating temperatures and the only alloy class of materials available for construction of such systems are the refractory metals niobium, tantalum, molybdenum and tungsten. The refractory metals in the past have been the construction materials selected for nuclear space power systems. The objective of this paper will be to review the past history and requirements for space nuclear power systems from the early 1960's through the SP-100 program. Also presented will be the past and present status of refractory metal alloy technology and what will be needed to support the next advanced nuclear space power system. The next generation of advanced nuclear space power systems can benefit from the review of this past experience. Because of a decline in the refractory metal industry in the United States, ready availability of specific refractory metal alloys is limited

  9. Evaluation of Terminated Nuclear Material Licenses

    International Nuclear Information System (INIS)

    Spencer, K.M.; Zeighami, E.A.

    1999-01-01

    This report presents the results of a six-year project that reviewed material licenses that had been terminated during the period from inception of licensing until approximately late-1994. The material licenses covered in the review project were Part 30, byproduct material licenses; Part 40, source material licenses; and Part 70, special nuclear material licenses. This report describes the methodology developed for the project, summarizes the findings of the license file inventory process, and describes the findings of the reviews or evaluations of the license files. The evaluation identified nuclear material use sites that need review of the licensing material or more direct follow-up of some type. The review process also identified licenses authorized to possess sealed sources for which there was incomplete or missing documentation of the fate of the sources

  10. Proceedings of the GLOBAL 2009 congress - The Nuclear Fuel Cycle: Sustainable Options and Industrial Perspectives

    International Nuclear Information System (INIS)

    2009-06-01

    GLOBAL 2009 is the ninth bi-annual scientific world meeting on the Nuclear Fuel Cycle (NFC) that started in 1993 in Seattle. This meeting has established itself as a dedicated international forum for experts, to provide an overall review of the status and new trends of research applications and policies related to the fuel cycle. The international nuclear community is actively developing advanced processes and innovative technologies that enhance economic competitiveness of nuclear energy and ensure its sustainability, through optimized utilization of natural resources, minimization of nuclear wastes, resistance to proliferation and compliance with safety requirements. In this context, and under the profound evolutions concerning energy supply, GLOBAL 2009 is a great opportunity for sharing ideas and visions on the NFC. Special emphasis are placed on the results of the international studies for developing next generation systems. GLOBAL 2009 highlights the technical challenges and successes involved in closing the NFC and recycling long lived nuclear waste. It is also an excellent occasion to review and discuss social and regulatory aspects as well as national plans and international policies and decision affecting the future of nuclear energy. This meeting provides a forum for the exchange of the newest ideas and developments related to the initiatives at of establishing an acceptable, reliable and universal international non proliferation regime. The congress, organized by the French Nuclear Energy Society (SFEN), under the aegis of the IAEA, NEA of the OECD and the UE Commission with the basic sponsorships of ANS, ENS and AESJ, combines plenary sessions, general panel sessions, parallel sessions and technical visits. The program has full length technical papers, which are peer reviewed and published in conference proceedings. A large industrial exhibition takes place to complement the congress. The GLOBAL 2009 congress is organized in coordination with the 2009

  11. Proceedings of the GLOBAL 2009 congress - The Nuclear Fuel Cycle: Sustainable Options and Industrial Perspectives

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-06-15

    GLOBAL 2009 is the ninth bi-annual scientific world meeting on the Nuclear Fuel Cycle (NFC) that started in 1993 in Seattle. This meeting has established itself as a dedicated international forum for experts, to provide an overall review of the status and new trends of research applications and policies related to the fuel cycle. The international nuclear community is actively developing advanced processes and innovative technologies that enhance economic competitiveness of nuclear energy and ensure its sustainability, through optimized utilization of natural resources, minimization of nuclear wastes, resistance to proliferation and compliance with safety requirements. In this context, and under the profound evolutions concerning energy supply, GLOBAL 2009 is a great opportunity for sharing ideas and visions on the NFC. Special emphasis are placed on the results of the international studies for developing next generation systems. GLOBAL 2009 highlights the technical challenges and successes involved in closing the NFC and recycling long lived nuclear waste. It is also an excellent occasion to review and discuss social and regulatory aspects as well as national plans and international policies and decision affecting the future of nuclear energy. This meeting provides a forum for the exchange of the newest ideas and developments related to the initiatives at of establishing an acceptable, reliable and universal international non proliferation regime. The congress, organized by the French Nuclear Energy Society (SFEN), under the aegis of the IAEA, NEA of the OECD and the UE Commission with the basic sponsorships of ANS, ENS and AESJ, combines plenary sessions, general panel sessions, parallel sessions and technical visits. The program has full length technical papers, which are peer reviewed and published in conference proceedings. A large industrial exhibition takes place to complement the congress. The GLOBAL 2009 congress is organized in coordination with the 2009

  12. Safeguards and Nuclear Material Management

    International Nuclear Information System (INIS)

    Stanchi, L.

    1991-01-01

    The book contains contributed papers from various authors on the following subjects: Safeguards systems and implementation, Measurement techniques: general, Measurement techniques: destructive analysis, Measurement techniques: non-destructive assay, Containment and surveillance, Spent fuel strategies, Material accounting and data evaluation

  13. Proceedings of the Canadian Nuclear Society ninth annual conference, 1988

    International Nuclear Information System (INIS)

    1988-01-01

    The 74 papers presented at this conference covered the following topics: operational enhancements of existing nuclear power plants; design of small reactors; accident behaviour in CANDU reactor fuel channels; fuel storage and waste management; reactor commissioning and decommissioning; nuclear safety experiments and modelling; the next generation of CANDU reactors; advances in nuclear engineering education in Canada; safety of small reactors; current position and improvements of fuel channels; current issues in nuclear safety; and, medical and industrial radiation applications

  14. Proceedings of the fourth Pacific Basin nuclear conference

    International Nuclear Information System (INIS)

    Vogt, E.W.; Ludgate, G.A.

    1983-01-01

    The 45 papers presented at this conference examined the status, future plans and significance of nuclear development for the Pacific Basin. Sessions covered the topics of energy and economics, nuclear power programs, the fuel cycle, waste management, seismic design, radionuclide production and use, and issues affecting nuclear goals

  15. Proceedings of the 3. Workshop on Nuclear Physics in Brazil

    International Nuclear Information System (INIS)

    1980-01-01

    This publication is the final report of the III Workshop on Nuclear Physics in Brazil. Many works were presented on the fields related to Nuclear Physics. It was organized some work groups which discussed the following topics: Perspectivas of Nuclear Physics in Brazil, Personnel Formation and Related Instrumentation. (A.C.A.S.) [pt

  16. Proceedings of 1. Regional Meeting on Nuclear Applications

    International Nuclear Information System (INIS)

    1990-01-01

    This Meeting describes nuclear methods and techniques, emphasizing the development or adaptation of methodologies and instrumentations for national conditions. The works present here comprise several field of nuclear application as agronomy; industry; nuclear medicine; dosimetry; radiological protection and instrumentation. (C.G.C.)

  17. Proceeding of the Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology part II : Nuclear Chemistry, Process Technology, Radioactive Waste Management and Environment

    International Nuclear Information System (INIS)

    Sukarsono, R.; Ganang Suradjijo

    2002-01-01

    Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is a routine activity held by Centre for Research and Development of Advanced Technology, National Nuclear Energy Agency, for monitoring the research activity which achieved in National Nuclear Energy Agency. This proceedings contains a proposal about basic research in nuclear technology which has environment. This proceedings is the second part of the two parts which published in series. There are 57 articles which have separated index. (PPIN)

  18. Proceeding of the Scientific Meeting and Presentation on Basic Research of Nuclear Science and Technology: Book II. Nuclear Chemistry, Process Technology, and Radioactive Waste Processing and Environment

    International Nuclear Information System (INIS)

    1996-06-01

    The proceeding contains papers presented on Scientific Meeting and Presentation on on Basic Research of Nuclear Science and Technology, held in Yogyakarta, 25-27 April 1995. This proceeding is second part of two books published for the meeting contains papers on nuclear chemistry, process technology, and radioactive waste management and environment. There are 62 papers indexed individually. (ID)

  19. Thermoelectric materials -- New directions and approaches. Materials Research Society symposium proceedings, Volume 478

    Energy Technology Data Exchange (ETDEWEB)

    Tritt, T M; Kanatzidis, M G; Lyon, Jr, H B; Mahan, G D [eds.

    1997-07-01

    field believe that future advances in thermoelectric applications will come through research in new materials. The authors have many new methods of materials synthesis and much more rapid characterization of these materials than were available 20--30 years ago. They have tried to focus the symposium on new directions and new materials such as skutterudites, quantum well and superlattice structures, new metal chalcogenides, rare earth systems, and quasicrystals. Other new materials are also presented in these proceedings. Separate abstracts were prepared for all the papers in this volume.

  20. Hirschegg '95: Dynamical properties of hadrons in nuclear matter. Proceedings

    International Nuclear Information System (INIS)

    Feldmeier, H.; Noerenberg, W.

    1995-01-01

    The following topics were dealt with: Chiral symmetry, chiral condensates, in-medium effective chiral Lagrangians, Δ's in nuclei, nonperturbative QCD, electron scattering from nuclear matter, nuclear shadowing, QCD sum rules, deconfinement, ultrarelativistic heavy ion collisions, nuclear dimuon and electron pair production, photoproduction from nuclei, subthreshold K + production, kaon polarization in nuclear matter, charged pion production in relativistic heavy ion collisions, the Nambu-Jona-Lasinio model, the SU(3) L xSU(3) R sigma model, nonequilibrium dense nuclear matter, pion pair production at finite temperature. (HSI)

  1. Proceedings of national symposium on advanced instrumentation for nuclear research

    International Nuclear Information System (INIS)

    1993-01-01

    The National Symposium on Advanced Instrumentation for Nuclear Research was held in Bombay during January 27-29, 1993 at BARC. Progress of modern nuclear research is closely related to the availability of state of the art instruments and systems. With the advancements in experimental techniques and sophisticated detector developments, the performance specifications have become more stringent. State of the art techniques and diverse applications of sophisticated nuclear instrumentation systems are discussed along with indigenous efforts to meet the specific instrumentation needs of research programs in nuclear sciences. Papers of relevance to nuclear science and technology are indexed separately. (original)

  2. The physical protection of nuclear material and nuclear facilities

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    The latest review (1993) of this document was of limited scope and resulted in changes to the text of INFCIRC/225/Rev.2 designed to make the categorization table in that document consistent with the categorization table contained in the Convention on Physical Protection of Nuclear Materials. Consequently, a comprehensive review of INFCIRC/225 has not been conducted since 1989. Consequently, a meeting of national experts was convened from 2-5 June 1998 and from 27-29 October 1998 for a thorough review of INFCIRC/225/Rev.3. The revised document reflects the recommendations of the national experts to improve the structure and clarity of the document and to take account of improved technology and current international and national practices. In particular, a chapter has been added which provides specific recommendations related to sabotage of nuclear facilities and nuclear material. As a result of this addition, the title has been changed to 'The Physical Protection of Nuclear Material and Nuclear Facilities'. The recommendations presented in this IAEA document reflect a broad consensus among Member States on the requirements which should be met by systems for the physical protection of nuclear materials and facilities. It is hoped that they will provide helpful guidance for Member States.

  3. The physical protection of nuclear material and nuclear facilities

    International Nuclear Information System (INIS)

    1999-06-01

    The latest review (1993) of this document was of limited scope and resulted in changes to the text of INFCIRC/225/Rev.2 designed to make the categorization table in that document consistent with the categorization table contained in the Convention on Physical Protection of Nuclear Materials. Consequently, a comprehensive review of INFCIRC/225 has not been conducted since 1989. Consequently, a meeting of national experts was convened from 2-5 June 1998 and from 27-29 October 1998 for a thorough review of INFCIRC/225/Rev.3. The revised document reflects the recommendations of the national experts to improve the structure and clarity of the document and to take account of improved technology and current international and national practices. In particular, a chapter has been added which provides specific recommendations related to sabotage of nuclear facilities and nuclear material. As a result of this addition, the title has been changed to 'The Physical Protection of Nuclear Material and Nuclear Facilities'. The recommendations presented in this IAEA document reflect a broad consensus among Member States on the requirements which should be met by systems for the physical protection of nuclear materials and facilities. It is hoped that they will provide helpful guidance for Member States

  4. Nuclear materials transport in France

    International Nuclear Information System (INIS)

    Korycanek, J.

    1990-01-01

    About 1.5 million tons of uranium ore, 8000 tons of uranium concentrate, 1000 tons of UF 6 , 340 spent fuel containers, and 30 000 m 3 of nuclear wastes are transported annually by trucks, trains and ships in France. Annual costs of this transportation amount to 500-600 million FRF, and about 200 employees are engaged in this activity. Transportation of spent fuel to the La Hague and Marcoule fuel reprocessing plants, and the transport of plutonium are dealt with in detail. (Z.M.). 5 figs., 1 ref

  5. Verification and nuclear material security

    International Nuclear Information System (INIS)

    ElBaradei, M.

    2001-01-01

    Full text: The Director General will open the symposium by presenting a series of challenges facing the international safeguards community: the need to ensure a robust system, with strong verification tools and a sound research and development programme; the importance of securing the necessary support for the system, in terms of resources; the effort to achieve universal participation in the non-proliferation regime; and the necessity of re-energizing disarmament efforts. Special focus will be given to the challenge underscored by recent events, of strengthening international efforts to combat nuclear terrorism. (author)

  6. Dismantling of nuclear facilities and related problems - Conference proceedings

    International Nuclear Information System (INIS)

    Tournebize, Frederic; Bordet, Didier; Charlety, Philippe; Gore, Thierry; Estrade, Jerome; Lemaire, Hermine; Ginet, Annick; Fabrier, Lionel; Evrard, Lydie; Furois, Timothee; Butez, Marc; Dutzer, Michel; Faure, Vincent; Billarand, Yann; Menuet, Lise; Lahaye, Thierry; Pin, Alain; Mougnard, Philippe; Charavy, Sylvain; Poncet, Philippe; Moggia, Fabrice; Dochy, Arnaud; Benjamin, Patrick; Poncet, Pierre-Emmanuel; Beneteau, Yannick; Richard, Jean-Baptiste; Pellenz, Gilles; Ollivier Dehaye, Catherine; Gerard, Stephane; Denissen, Luc; Davain, Henri; Duveau, Florent; Guyot, Jean-Luc; Ardellier, Luc

    2012-11-01

    facilitating the definitive shutdown of the Jules Horowitz reactor (J. Estrade); 17 - Integration of dismantling at the design stage of the French EPR reactor (Y. Beneteau, J.P. Richard); 18 - Use of the Gampix gamma camera at dismantling sites (H. Lemaire); 19 - Stakes for the wastes intended to be disposed off in waste centres in operation (F. Dutzer); 20 - Cleansing of non-nuclear contaminated sites (V. Faure); 21 - Rehabilitation of dismantling sites - management plan for the old effluents channel of the Brennilis effluents processing plant (G. Pellenz, C. Ollivier-Dehaye); 22 - Problem of confinement keeping during deconstruction (A. Ginet, L. Fabrier); 23 - Project of wells cleansing at the irradiated materials workshop (AMI) of Chinon NPP (F. Duveau); 24 - Nuclear decontamination using a laser (F. Moggia); 25 - TIVA, adaptable and ventilated intervention dress (A. Dochy, P. Benjamin); 26 - Dismantling project - optimisation thanks to virtual reality-based software solutions (L. Ardellier, A. Pin)

  7. Technical records as material evidence in criminal proceedings

    Directory of Open Access Journals (Sweden)

    Fitim Shishani

    2017-03-01

    Full Text Available Nowadays, with the aid of technical records - recordings (audio, visual or combined audiovisual events and occurrences can be registered in the outside world in detail. The recording enables the creator or anyone who has it in disposal that at any moment of its reproduction, it can be found in detail how the recorded event has happened or how an occurrence seemed at the time of the recording. Among the current formats of technical records are included: photography, filming, magnetic, magnetoscope, and videophone recording etc. (Sahiti & Murati 2016, 295. The possibility provided by the rapid technical development is also of interest to criminal procedure because technical records containing any fact that may be proved in criminal proceedings may serve as a source of knowledge about facts. In other words, they may serve as evidence to establish facts in criminal proceedings. Given the extensive options that technical fact recordings provide, entities that use the aid of various devices from this fi eld, as well as the different purposes of the author of the recording which have led to the case of making the recording, there is a reasonable question of the permission on their use as evidence in criminal proceedings. In Kosovo, the situation is clear in terms of recordings made in the criminal procedure, as Kosovo CCP 1 provides the possibility of photographing, filming, sketching, etc., of the crime scene, audio visual recording etc. examination of persons (defendant, witness, expert or recordings of any action on judicial review.

  8. Proceedings of the 2011 symposium on nuclear data

    International Nuclear Information System (INIS)

    Harada, Hideo; Yokoyama, Kenji; Iwamoto, Nobuyuki; Nakamura, Shoji

    2012-12-01

    The 2011 data symposium on nuclear data, organized by the Nuclear Data Division of Atomic Energy Society of Japan (AESJ) was held at Ricotti, Tokai, on Nov. 16 and 17, 2011 in cooperation with Nuclear Science and Engineering Directorate of JAEA and North-Kanto Branch of AESJ. The symposium was devoted for discussions and presentations of current topics in the field of nuclear data such as nuclear accident and accident analysis code, innovative methods on nuclear data theory and measurements, and nuclear data applications, including 2 tutorial talks, NJOY99 and PHITS. Talks as well as posters presented at the symposium aroused lively discussions among 97 participants. This report contains 34 papers submitted from the oral and poster presenters. (author)

  9. Radiation Effects in Nuclear Waste Materials

    International Nuclear Information System (INIS)

    Weber, William J.

    2005-01-01

    The objective of this project is to develop a fundamental understanding of radiation effects in glasses and ceramics, as well as the influence of solid-state radiation effects on aqueous dissolution kinetics, which may impact the performance of nuclear waste forms and stabilized nuclear materials. This work provides the underpinning science to develop improved glass and ceramic waste forms for the immobilization and disposition of high-level tank waste, excess plutonium, plutonium residues and scrap, other actinides, and other nuclear waste streams. Furthermore, this work is developing develop predictive models for the performance of nuclear waste forms and stabilized nuclear materials. Thus, the research performed under this project has significant implications for the immobilization of High-Level Waste (HLW) and Nuclear Materials, two mission areas within the Office of Environmental Management (EM). With regard to the HLW mission, this research will lead to improved understanding of radiation-induced degradation mechanisms and their effects on dissolution kinetics, as well as development of predictive models for waste form performance. In the Nuclear Materials mission, this research will lead to improvements in the understanding of radiation effects on the chemical and structural properties of materials for the stabilization and long-term storage of plutonium, highly-enriched uranium, and other actinides. The research uses plutonium incorporation, ion-beam irradiation, and electron-beam irradiation to simulate the effects of alpha decay and beta decay on relevant glasses and ceramics. The research under this project has the potential to result in improved glass and ceramic materials for the stabilization and immobilization of high-level tank waste, plutonium residues and scraps, surplus weapons plutonium, highly-enriched uranium, other actinides, and other radioactive materials

  10. Radiation Effects in Nuclear Waste Materials

    International Nuclear Information System (INIS)

    Weber, William J.; Wang, Lumin; Hess, Nancy J.; Icenhower, Jonathan P.; Thevuthasan, Suntharampillai

    2003-01-01

    The objective of this project is to develop a fundamental understanding of radiation effects in glasses and ceramics, as well as the influence of solid-state radiation effects on aqueous dissolution kinetics, which may impact the performance of nuclear waste forms and stabilized nuclear materials. This work provides the underpinning science to develop improved glass and ceramic waste forms for the immobilization and disposition of high-level tank waste, excess plutonium, plutonium residues and scrap, other actinides, and other nuclear waste streams. Furthermore, this work is developing develop predictive models for the performance of nuclear waste forms and stabilized nuclear materials. Thus, the research performed under this project has significant implications for the immobilization of High-Level Waste (HLW) and Nuclear Materials, two mission areas within the Office of Environmental Management (EM). With regard to the HLW mission, this research will lead to improved understanding of radiation-induced degradation mechanisms and their effects on dissolution kinetics, as well as development of predictive models for waste form performance. In the Nuclear Materials mission, this research will lead to improvements in the understanding of radiation effects on the chemical and structural properties of materials for the stabilization and long-term storage of plutonium, highly-enriched uranium, and other actinides. The research uses plutonium incorporation, ion-beam irradiation, and electron-beam irradiation to simulate the effects of alpha decay and beta decay on relevant glasses and ceramics. The research under this project has the potential to result in improved glass and ceramic materials for the stabilization and immobilization of high-level tank waste, plutonium residues and scraps, surplus weapons plutonium, highly-enriched uranium, other actinides, and other radioactive materials

  11. Polymers for nuclear materials processing

    International Nuclear Information System (INIS)

    Jarvinen, G.; Benicewicz, B.; Duke, J.

    1996-01-01

    This is the final report of a one-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The use of open-celled microcellular foams as solid sorbents for metal ions and other solutes could provide a revolutionary development in separation science. Macroreticular and gel-bead materials are the current state-of-the-art for solid sorbents to separate metal ions and other solutes from solution. The new polymer materials examined in this effort offer a number of advantages over the older materials that can have a large impact on industrial separations. The advantages include larger usable surface area in contact with the solution, faster sorption kinetics, ability to tailor the uniform cell size to a specific application, and elimination of channeling and packing instability

  12. Measurement control program for nuclear material accounting

    International Nuclear Information System (INIS)

    Brouns, R.J.; Roberts, F.P.; Merrill, J.A.; Brown, W.B.

    1980-06-01

    A measurement control program for nuclear material accounting monitors and controls the quality of the measurments of special nuclear material that are involved in material balances. The quality is monitored by collecting data from which the current precision and accuracy of measurements can be evaluated. The quality is controlled by evaluations, reviews, and other administrative measures for control of selection or design of facilities, equipment and measurement methods and the training and qualification of personnel who perform SNM measurements. This report describes the most important elements of a program by which management can monitor and control measurement quality

  13. Proceedings of the Seminar on the Development of Nuclear Instrumentation Technology and Engineering

    International Nuclear Information System (INIS)

    Utaja; Setyanto; Suryanto; Martono, Herlan; Kristejo; Pribadi, Rukmono

    2003-01-01

    Proceedings of the Seminar on the Development of Nuclear Instrumentation Technology Engineering,all aspects of result research activity report that have been presented in Seminar of Development and Engineering on Medicine Industry and Environment was held on May 20, 2003. The Seminar encompass Instrumentation : Reactor Control, Industry, Medicine and based on Nuclear Instrumentation and Application, software relevant to Nuclear Engineering . The purpose of this seminar be able to information exchange among research walkers in National Nuclear Energy Agency. There are 20 papers which have separated Index

  14. Proceedings of NUCLEAR 2013 the 6th annual international conference on sustainable development through nuclear research and education. Part 1/3

    International Nuclear Information System (INIS)

    Constantin, Marin; Turcu, Ilie

    2013-01-01

    The proceedings of the NUCLEAR 2013 international conference on sustainable development through nuclear research and education held at INR-Pitesti on May, 2-24 2013 contain 79 communications presented in two plenary sessions (6 and 8 talks, respectively) and three sections addressing the themes of Nuclear energy, Environmental protection, and Sustainable development . In turn these sections are addressing the following items: Section 1.1 - Nuclear Technology and Materials (33 papers); Section 1.2 Nuclear Safety and Sever Accidents (16 papers); 1.3 Nuclear Reactors and Gen IV (20 papers); 2.1 Radioactive Waste Management (13 papers); 2.2 Radioprotection and 2.3 Air, Water, Soil Protection (17 papers); 3.1 Polices and Strategies in Nuclear Research (0 papers); 3.2 International Partnership for a Sustainable Development (2 papers); 3.3 Education, Continuous Formation and Knowledge Transfer (1 papers). These papers are presented as abstracts in 'Nuclear 2013 - Book of Abstracts', separately processed

  15. Proceedings of NUCLEAR 2015 the 8th annual international conference on sustainable development through nuclear research and education. Part 1/3

    International Nuclear Information System (INIS)

    Constantin, Marin; Turcu, Ilie

    2015-01-01

    The proceedings of the NUCLEAR 2015 the 8"t"h annual international conference on sustainable development through nuclear research and education. Part 1/3 held at INR-Pitesti on May, 27-29 contain 62 communications presented in two plenary sessions and three sections addressing the themes of Nuclear energy, Environmental protection and Sustainable development. In turn these sections are addressing the following items: Section 1.1 Nuclear safety and severe accidents (7 papers); Section 1.2 Nuclear reactors and gen. IV (5 papers); Section 1.3 Nuclear technology and materials (19 papers); Section 2.1 Radioprotection & air, water and soil protection (1 paper); Section 2.2 Radioactive waste management (9 papers); Section 3.1 policies and strategies in nuclear research (1 paper); Section 3.2 Education, training and knowledge management (16 papers); Section 3.3 International partnership for a sustainable development (4 papers). These papers are presented as abstracts in 'Nuclear 2015 - Book of Abstracts', separately processed

  16. Proceedings of the sixth conference of nuclear sciences and applications. Vol. 1-4

    International Nuclear Information System (INIS)

    1996-03-01

    The six conference on nuclear sciences and applications was held on 15-20 March, 1996 in Cairo. The specialists discussed nuclear Sciences. The applications of nuclear engineering, chemistry, radioactive waste management, nuclear fuel and nuclear material were discussed at the proceeing.More than 1000 paper

  17. Proceedings of the sixth conference of nuclear sciences and applications. Vol. 1-4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The six conference on nuclear sciences and applications was held on 15-20 March, 1996 in Cairo. The specialists discussed nuclear Sciences. The applications of nuclear engineering, chemistry, radioactive waste management, nuclear fuel and nuclear material were discussed at the proceeing.More than 1000 paper.

  18. Naturally occurring radioactive materials (NORM IV). Proceedings of an international conference

    International Nuclear Information System (INIS)

    2005-10-01

    Radionuclides of natural origin are ubiquitous in both working and public environments, although their activity concentrations vary considerably. Exposures to natural sources are in most cases not a matter for regulatory concern. However, there are situations where exposures to natural sources may warrant consideration as to whether controls should be applied. One such situation is where the conditions are conducive to the buildup of elevated concentrations of radon in air. Another situation is the mining and/or processing of material where the activity concentrations of radionuclides of natural origin in the material itself, or in any material arising from the process, are significantly elevated - such material has come to be referred to as Naturally Occurring Radioactive Material (NORM). In the past, regulatory attention has been focused mostly on exposures arising from the mining and processing of uranium ores because such activities are part of the nuclear fuel cycle. More recently, attention has been broadened to include exposures from other industrial activities involving NORM, in recognition of the potential for such activities to also give rise to significant exposures of workers and members of the public if not adequately controlled. More and more countries are now including provisions in their national legislation and regulations for the control of exposures to natural sources, and the body of radiological data on such exposures is growing rapidly. This international conference, NORM IV, follows three previous conferences dealing with radon and NORM. The first was held in Amsterdam in 1997, the second in Krefeld, Germany in 1998 (NORM II), and the third in Brussels in 2001 (NORM III). In addition, an International Symposium on Technologically Enhanced Natural Radiation was held in Rio de Janeiro in 1999 - the IAEA was involved in the organization of that symposium, and published the proceedings as IAEA-TECDOC-1271. The main topic addressed at NORM IV was

  19. The regulations concerning refining business of nuclear source material and nuclear fuel materials

    International Nuclear Information System (INIS)

    1981-01-01

    This rule is established under the provisions concerning refining business in the law concerning the regulation of nuclear raw materials, nuclear fuel materials and nuclear reactors and the ordinance for the execution of this law, and to enforce them. Basic terms are defined, such as: exposure radiation dose, cumulative dose, control area, surrounding monitoring area and worker. The application for the designation for refining business under the law shall be classified into the facilities for crushing and leaching-filtration, thikening, and refining, the storage facilities for nuclear raw materials and nuclear fuel materials, and the disposal facilities for radioactive wastes, etc. To the application, shall be attached business plans, the explanations concerning the technical abilities of applicants and the prevention of hazards by nuclear raw materials and nuclear fuel materials regarding refining facilities, etc. Records shall be made on the accept, delivery and stock of each kind of nuclear raw materials and nuclear fuel materials, radiation control, the maintenance of and accidents in refining facilities, and kept for specified periods, respectively. Security regulations shall be enacted for each works or enterprise on the functions and organizations of persons engaged in the control of refining facilities, the operation of the apparatuses which must be controlled for the prevention of accidents, and the establishment of control area and surrounding monitoring area, etc. The report on the usage of internationally regulated goods and the measures taken at the time of danger are defined particularly. (Okada, K.)

  20. Nuclear material accounting software for Ukraine

    International Nuclear Information System (INIS)

    Doll, M.; Ewing, T.; Lindley, R.; McWilliams, C.; Roche, C.; Sakunov, I.; Walters, G.

    1999-01-01

    Among the needs identified during initial surveys of nuclear facilities in Ukraine was improved accounting software for reporting material inventories to the regulatory body. AIMAS (Automated Inventory/Material Accounting System) is a PC-based application written in Microsoft Access that was jointly designed by an US/Ukraine development team. The design is highly flexible and configurable, and supports a wide range of computing infrastructure needs and facility requirements including situations where networks are not available or reliable. AIMAS has both English and Russian-language options for displays and reports, and it operates under Windows 3.1, 95, or NT 4.0trademark. AIMAS functions include basic physical inventory tracking, transaction histories, reporting, and system administration functions (system configuration, security, data backup and recovery). Security measures include multilevel password access control, all transactions logged with the user identification, and system administration control. Interfaces to external modules provide nuclear fuel burn-up adjustment and barcode scanning capabilities for physical inventory taking. AIMAS has been installed at Kiev Institute of Nuclear Research (KINR), South Ukraine Nuclear Power Plant (SUNPP), Kharkov Institute of Physics and Technology (KIPT), Sevastopol Institute of Nuclear Energy and Industry (SINEI), and the Ministry of Environmental Protection and Nuclear Safety/Nuclear Regulatory Administration (MEPNS/NRA). Facility specialists are being trained to use the application to track material movement and report to the national regulatory authority

  1. Proceedings of 12th international workshop on Asian network for accelerator-driven system and nuclear transmutation technology (ADS+NTT 2014)

    International Nuclear Information System (INIS)

    Pyeon, Cheol Ho

    2015-01-01

    The proceedings describe the current status on research and development (R and D) of accelerator-driven system (ADS) and nuclear transmutation techniques (NTT), including nuclear data, accelerator techniques, Pb-Bi target, fuel technologies and reactor physics, in East Asian countries: China, Japan and Korea. The proceedings also include all presentation materials presented in 'the 12th International Workshop on Asian Network for ADS and NTT (ADS+NTT 2014)' held at the Institute of Nuclear Energy and Safety Technology, Chinese Academy of Sciences, Hefei, China on 15th and 16th December, 2014. The objective of this workshop is to make actual progress of ADS R and D especially in East Asian countries, as well as in European countries, through sharing mutual interests and conducting the information exchange each other. The report is composed of these following items: Presentation materials: ADS+NTT 2014. (author)

  2. Safeguarding nuclear weapon: Usable materials in Russia

    International Nuclear Information System (INIS)

    Cochran, T.

    1998-01-01

    Both the United States and Russia are retaining as strategic reserves more plutonium and HEU for potential reuse as weapons, than is legitimately needed. Both have engaged in discussions and have programs in various stages of development to dispose of excess plutonium and HEU. These fissile material disposition programs will take decades to complete. In the interim there will be, as there is now, hundreds of tons of separated weapon-usable fissile material stored in tens of thousands of transportable canisters, each containing from a few to several tons of kgs of weapon-usable fissile material. This material must be secured against theft and unauthorized use. To have high confidence that the material is secure, one must establish criteria against which the adequacy of the protective systems can be judged. For example, one finds such criteria in US Nuclear Regulatory Commission (USNRC) regulations for the protection of special nuclear materials

  3. Mass spectrometry of nuclear materials

    International Nuclear Information System (INIS)

    Shields, W.R.

    1989-01-01

    Measurements of the 235 U/ 238 U ratio in product-quality material have improved from uncertainties of 0.1 percent (rel) to 0.2 percent since the Manhattan Project. The hardware and procedural changes responsible for these measurement improvements are traced and discussed

  4. Chimera of new nuclear materials

    International Nuclear Information System (INIS)

    Bush, S.H.

    1975-01-01

    The current and future needs in materials for light water reactors and liquid metal fast breeder reactors are reviewed. Information and discussions are included on boiling water reactors, pressurized water reactors, liquid metal fast breeder reactors, corrosion of piping systems and steam generators, ferritic steels, stainless steels, Inconel 600, pressure vessels, and radiation damage. (U.S.)

  5. Uncontrolled transport of nuclear materials

    International Nuclear Information System (INIS)

    Wassermann, U.

    1985-01-01

    An account is given of international transport of plutonium, uranium oxides, uranium hexafluoride, enriched uranium and irradiated fuel for reprocessing. Referring to the sinking of the 'Mont Louis', it is stated that the International Maritime Organization has been asked by the National Union of Seamen and 'Greenpeace' to bar shipment of radioactive material until stricter international safety regulations are introduced. (U.K.)

  6. National Public Information Symposium on Peaceful Uses of Nuclear Energy, NUC Info'2000. Radioactive Waste Management and Site Restoration in Uranium Industry. Proceedings. Volume 1

    International Nuclear Information System (INIS)

    Dobos, Ion; Comsa, Olivia

    2000-01-01

    These proceedings published in two volumes contain materials presented at the National Public Information Symposium on Peaceful Uses of Nuclear Energy, NUC Info'2000, Radioactive Waste Management and Site Restoration in Uranium Industry, held on 5. September to 8. September 2000 at Baita Bihor, Romania. As the name of Symposium indicates, this manifestation is addressed not only to specialists but rather to the public at large. The proceedings are structured in 4 sections: 1. Management of radioactive waste arising from uranium mining, milling and decommissioning; 2. Uranium mine close-down; 3. Environmental restoration of uranium mining and milling sites; 4. Management of radioactive waste arising from nuclear applications. The first volume also contains an inaugural session dedicated to nuclear power, nuclear fuel cycle and development of uranium industry in Romania. The contributions in the first volume deal with the management of radioactive waste arising from uranium mining, milling and decommissioning and uranium mine close-out

  7. Software development for managing nuclear material database

    International Nuclear Information System (INIS)

    Tondin, Julio Benedito Marin

    2011-01-01

    In nuclear facilities, the nuclear material control is one of the most important activities. The Brazilian National Commission of Nuclear Energy (CNEN) and the International Atomic Energy Agency (IAEA), when inspecting routinely, regards the data provided as a major safety factor. Having a control system of nuclear material that allows the amount and location of the various items to be inspected, at any time, is a key factor today. The objective of this work was to enhance the existing system using a more friendly platform of development, through the VisualBasic programming language (Microsoft Corporation), to facilitate the operation team of the reactor IEA-R1 Reactor tasks, providing data that enable a better and prompter control of the IEA-R1 nuclear material. These data have allowed the development of papers presented at national and international conferences and the development of master's dissertations and doctorate theses. The software object of this study was designed to meet the requirements of the CNEN and the IAEA safeguard rules, but its functions may be expanded in accordance with future needs. The program developed can be used in other reactors to be built in the country, since it is very practical and allows an effective control of the nuclear material in the facilities. (author)

  8. Proceeding of the National Seminar on Research and Management of Nuclear Equipment: Book II

    International Nuclear Information System (INIS)

    Tjipto Sujitno; Syarip; Agus Taftazani; Elisabeth Supriyatni; Prayitno; MV Purwani; Budi Setiawan; Prajitno; Rany Saptaaji; Bambang Siswanto; Eko Priyono; Jumari

    2013-09-01

    The scientific meeting and presentation on accelerator technology and its applications was held by PTAPB BATAN on 11 September 2013. This meeting aims to promote the technology and its applications to accelerator scientists, academics, researchers and technology users as well as accelerator-based accelerator research that have been conducted by researchers in and outside BATAN. This proceeding contains 49 papers about , chemistry, physics, accelerator, nuclear instrument and nuclear reactor, etc. (PPIKSN)

  9. Proceedings of the 1st conference on nuclear structure data evaluation

    International Nuclear Information System (INIS)

    Firestone, R.B.; Shirley, V.S.; Dairiki, J.M.

    1982-04-01

    The 1st Conference on Nuclear Structure Data Evaluation was organized by the Isotopes Project of the Lawrence Berkeley Laboratory in order to encourage the open discussion of the scientific aspects of ENSDF production and usage. Summaries of the roundtable discussion sessions, abstracts of the presented papers, and additional contributed papers are contained in these Proceedings

  10. Proceedings of the 32. annual conference of the Canadian Nuclear Association

    International Nuclear Information System (INIS)

    1992-01-01

    The conference proceedings comprise 34 papers, arranged under the following sessions: Plenary; The international CANDU program; Canadian used fuel management program; Public information advocates; Fuel and electricity supply; In which direction should reactors advance?; Canadian advanced nuclear research programs; International cooperation in operations; Safety in design, operation, regulation; Renovation of operating stations; CNS/CNA luncheon addresses. The individual papers have been abstracted separately

  11. Proceedings of the 13. annual conference of the Canadian Nuclear Society. V. 1

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-31

    Volume 1 of the proceedings of the 13. annual conference of the Canadian Nuclear Society includes sessions on the following topics: reactor physics, new concepts and technology, fuel behaviour, reactor design, safety analysis, fuel channel behaviour, equipment and design qualification. The individual papers have been abstracted separately.

  12. Fully three-dimensional image reconstruction in radiology and nuclear medicine. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    The proceedings of the meeting on ''fully three-dimensional image reconstruction in radiology and nuclear medicine'' covers contributions on the following topics: CT imaging, PET imaging, fidelity; iterative and few-view CT, CT-analytical; PET/SPECT Compton analytical; doses - spectral methods; phase contrast; compressed sensing- sparse reconstruction; special issues; motion - cardiac.

  13. Plasma physics and controlled nuclear fusion research 1994. V. 3. Proceedings of the fifteenth international conference

    International Nuclear Information System (INIS)

    1996-01-01

    This is the third volume of the proceedings of the 15th International Atomic Energy Agency Conference on Plasma Physics and Controlled Nuclear Fusion Research held in Seville, Spain, from 26 September - 1 October 1994. Contained in it are 29 papers on inertial confinement and 46 papers on magnetic confinement. Refs, figs, tabs

  14. Proceedings of the seventh symposium on training of nuclear facility personnel

    International Nuclear Information System (INIS)

    1987-04-01

    Separate abstracts were prepared for 45 papers in this conference proceedings. Topics covered include influences on nuclear training, the relationship between human factors and training, factors affecting job performance, current training methods, the relationship between training and education, emerging training techniques, evaluation to improve performance, and measurement of the impact of training

  15. Gamma spectrometric discrimination of special nuclear materials

    International Nuclear Information System (INIS)

    Dowdall, M.; Mattila, A.; Ramebaeck, H.; Aage, H.K.; Palsson, S.E.

    2012-12-01

    This report presents details pertaining to an exercise conducted as part of the NKS-B programme using synthetic gamma ray spectra to simulate the type of data that may be encountered in the interception of material potentially containing special nuclear materials. A range of scenarios were developed involving sources that may or may not contain special nuclear materials. Gamma spectral data was provided to participants as well as ancillary data and participants were asked, under time constraint, to determine whether or not the data was indicative of circumstances involving special nuclear materials. The situations varied such that different approaches were required in order to obtain the correct result in each context. In the majority of cases participants were able to correctly ascertain whether or not the situations involved special nuclear material. Although fulfilling the primary goal of the exercise, some participants were not in a position to correctly identify with certainty the material involved, Situations in which the smuggled material was being masked by another source proved to be the most challenging for participants. (Author)

  16. Modernizing computerized nuclear material accounting systems

    International Nuclear Information System (INIS)

    Erkkila, B.H.; Claborn, J.

    1995-01-01

    DOE Orders and draft orders for nuclear material control and accountability address a complete material control and accountability (MC and A) program for all DOE contractors processing, using, or storing nuclear materials. A critical element of an MC and A program is the accounting system used to track and record all inventories of nuclear material and movements of materials in those inventories. Most DOE facilities use computerized accounting systems to facilitate the task of accounting for all their inventory of nuclear materials. Many facilities still use a mixture of a manual paper system with a computerized system. Also, facilities may use multiple systems to support information needed for MC and A. For real-time accounting it is desirable to implement a single integrated data base management system for a variety of users. In addition to accountability needs, waste management, material management, and production operations must be supported. Information in these systems can also support criticality safety and other safety issues. Modern networked microcomputers provide extensive processing and reporting capabilities that single mainframe computer systems struggle with. This paper describes an approach being developed at Los Alamos to address these problems

  17. Gamma spectrometric discrimination of special nuclear materials

    Energy Technology Data Exchange (ETDEWEB)

    Dowdall, M. [Norwegian Radiation Protection Authority (Norway); Mattila, A. [Radiation and Nuclear Safety Authority, Helsinki (Finland); Ramebaeck, H. [Swedish Defence Research Agency, Stockholm (Sweden); Aage, H.K. [Danish Emergency Management Agency, Birkeroed (Denmark); Palsson, S.E. [Icelandic Radiation Safety Authority, Reykjavik (Iceland)

    2012-12-15

    This report presents details pertaining to an exercise conducted as part of the NKS-B programme using synthetic gamma ray spectra to simulate the type of data that may be encountered in the interception of material potentially containing special nuclear materials. A range of scenarios were developed involving sources that may or may not contain special nuclear materials. Gamma spectral data was provided to participants as well as ancillary data and participants were asked, under time constraint, to determine whether or not the data was indicative of circumstances involving special nuclear materials. The situations varied such that different approaches were required in order to obtain the correct result in each context. In the majority of cases participants were able to correctly ascertain whether or not the situations involved special nuclear material. Although fulfilling the primary goal of the exercise, some participants were not in a position to correctly identify with certainty the material involved, Situations in which the smuggled material was being masked by another source proved to be the most challenging for participants. (Author)

  18. Proceedings from the Fissile Material Cut-off seminar in Stockholm

    International Nuclear Information System (INIS)

    Arbman, G.

    1998-01-01

    The Swedish Defence Research Establishment hosted an international expert seminar on the subject of verifying a prohibition of the production of fissile material for nuclear weapons purpose (cut-off) in Stockholm, June 3-5 1998. The objective of the seminar was to provide an opportunity for informal discussions among scientific and technical experts on various technical matters relating to the verification of a future Fissile Material Cut-off Treaty (FMCT). A stated aim of the seminar was to keep issues of scope to a minimum. Invited speakers and commentators were given an opportunity to present their views as written contributions. The present seminar proceedings are essentially the result of these views. In addition, short summaries of the discussions following each session are included. Although an attempt was made to be as complete and accurate as possible in reproducing these discussions, the editors apologise if some important points or statements have been omitted. If so, the main reason is that the documentation of the discussions were based on written notes, not taped recordings. Eight longer contributions have been separately indexed

  19. Proceedings from the Fissile Material Cut-off seminar in Stockholm

    Energy Technology Data Exchange (ETDEWEB)

    Arbman, G. [ed.

    1998-07-01

    The Swedish Defence Research Establishment hosted an international expert seminar on the subject of verifying a prohibition of the production of fissile material for nuclear weapons purpose (cut-off) in Stockholm, June 3-5 1998. The objective of the seminar was to provide an opportunity for informal discussions among scientific and technical experts on various technical matters relating to the verification of a future Fissile Material Cut-off Treaty (FMCT). A stated aim of the seminar was to keep issues of scope to a minimum. Invited speakers and commentators were given an opportunity to present their views as written contributions. The present seminar proceedings are essentially the result of these views. In addition, short summaries of the discussions following each session are included. Although an attempt was made to be as complete and accurate as possible in reproducing these discussions, the editors apologise if some important points or statements have been omitted. If so, the main reason is that the documentation of the discussions were based on written notes, not taped recordings. Eight longer contributions have been separately indexed.

  20. Passive nondestructive assay of nuclear materials

    International Nuclear Information System (INIS)

    Reilly, D.; Ensslin, N.; Smith, H. Jr.; Kreiner, S.

    1991-03-01

    The term nondestructive assay (NDA) is applied to a series of measurement techniques for nuclear fuel materials. The techniques measure radiation induced or emitted spontaneously from the nuclear material; the measurements are nondestructive in that they do not alter the physical or chemical state of the nuclear material. NDA techniques are characterized as passive or active depending on whether they measure radiation from the spontaneous decay of the nuclear material or radiation induced by an external source. This book emphasizes passive NDA techniques, although certain active techniques like gamma-ray absorption densitometry and x-ray fluorescence are discussed here because of their intimate relation to passive assay techniques. The principal NDA techniques are classified as gamma-ray assay, neutron assay, and calorimetry. Gamma-ray assay techniques are treated in Chapters 1--10. Neutron assay techniques are the subject of Chapters 11--17. Chapters 11--13 cover the origin of neutrons, neutron interactions, and neutron detectors. Chapters 14--17 cover the theory and applications of total and coincidence neutron counting. Chapter 18 deals with the assay of irradiated nuclear fuel, which uses both gamma-ray and neutron assay techniques. Chapter 19 covers perimeter monitoring, which uses gamma-ray and neutron detectors of high sensitivity to check that no unauthorized nuclear material crosses a facility boundary. The subject of Chapter 20 is attribute and semiquantitative measurements. The goal of these measurements is a rapid verification of the contents of nuclear material containers to assist physical inventory verifications. Waste and holdup measurements are also treated in this chapter. Chapters 21 and 22 cover calorimetry theory and application, and Chapter 23 is a brief application guide to illustrate which techniques can be used to solve certain measurement problems

  1. Proceedings of the symposium on frontier nuclear physics (FRONP99)

    International Nuclear Information System (INIS)

    Chiba, Satoshi

    2000-01-01

    The symposium on Frontier Nuclear Physics (FRONP99), organized by the Research Group for Hadron Science, Advanced Science Research Center, under close cooperation with the Research Center for Nuclear Physics, Osaka University and High Energy Accelerator Research Organization, was held at Tokai Research Establishment of JAERI on August 2 to 4, 1999. The symposium was devoted for discussions and presentations of research results in wide variety of fields such as hyper nuclear physics, lepton nuclear physics, quark nuclear physics, unstable nuclear physics, superheavy elements and heavy-ion physics. Three talks on the joint project between JAERI (Neutron Science Research Center) and KEK (JHF) were presented in a public session. Thirty three talks on these topics presented at the symposium aroused lively discussions among approximately 70 participants. This report contains 26 papers submitted from the lecturers. (author)

  2. Proceedings of the European Nuclear Conference - ENC 2014

    International Nuclear Information System (INIS)

    2014-01-01

    The European Nuclear Conference (ENC) is the get-together for the international nuclear industry and science community. ENC 2014 provides a platform for the nuclear science community to share their experience and to learn about the latest developments going on in nuclear research and their practical applications. It will furthermore exploit synergy among scientists, industry representatives, policy-makers and citizens on wider societal issues that impact upon how the nuclear science community carries out its work. The conference programme covers the following areas: Plant operations and safety; Education, training and knowledge management; The fuel cycle; Reactor technologies; New Build; End of Use management; Life science applications; Non-power applications; Nuclear in the civil society

  3. Proceedings of the European Nuclear Conference - ENC 2012

    International Nuclear Information System (INIS)

    2012-01-01

    The European Nuclear Conference-ENC is the largest international conference of its kind on the European event calendar. This European Nuclear Society-ENS event has a multidisciplinary approach, looking at nuclear science and technology in energy production, non-power industrial and life science applications. ENC 2012 will be a unique networking event for scientists, nuclear industry representatives and policy makers, who can consider and discuss ideas and innovations that will drive the technological developments of the future. The European Nuclear Conference is known for the high standard of papers presented. Key themes of ENC 2012 will include state-of-the-art research and development in areas such as: Reactor technologies, The fuel cycle, Plant operations, New Build, End of Use management, Life science applications, Non-power industrial applications, Education, training and knowledge management, Nuclear in the civil society. (authors)

  4. New materials options for nuclear systems

    International Nuclear Information System (INIS)

    Jones, R.H.; Garner, F.A.; Bruemmer, S.M.; Gelles, D.S.

    1989-01-01

    Development of new materials for nuclear reactor systems is continuing to produce options for improved reactor designs. Materials with reduced environment-induced crack growth is a key materials issue for the light water reactor (LWR) industry while the development of low activation ferritic, austenitic and vanadium alloys has been an active area for materials development for fusion reactor structural applications. Development of advanced materials such as metal matrix and ceramic matrix composites for reactor systems have received a limited amount of attention. (author)

  5. Proceedings of the 5th nuclear science and technology conference

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-11-01

    The 5th conference on nuclear science and technology was held on 21-23 November, 1992 in Bangkok. This conference contain papers on non-power applications of nuclear technology in medicine, agriculture and industry. These application including irradiation of food for desinfestation; tram technologies used in diagnosis and therapy and radiation chemistry important to industrial processes. Some technologies which evolved from the development of the nuclear power industry are also discussed.

  6. Proceedings of the 6th nuclear science and technology conference

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    The 6th conference on nuclear science and technology was held on 2 - 4 December, 1996 in Bangkok. This conference contain papers on non-power applications of nuclear technology in medicine, agriculture and industry. These application include irradiation of food for des infestation; tram technologies used in diagnosis and therapy and radiation chemistry important to industrial processes. Some technologies which evolved from the development of nuclear power industry are also discussed

  7. Proceedings of the 5th nuclear science and technology conference

    International Nuclear Information System (INIS)

    1994-11-01

    The 5th conference on nuclear science and technology was held on 21-23 November, 1992 in Bangkok. This conference contain papers on non-power applications of nuclear technology in medicine, agriculture and industry. These application including irradiation of food for desinfestation; tram technologies used in diagnosis and therapy and radiation chemistry important to industrial processes. Some technologies which evolved from the development of the nuclear power industry are also discussed

  8. Proceedings of the 7. Nuclear Science and Technology Conference

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-01

    The 7. conference on nuclear science and technology was held on 1-2 December 1998 in Bangkok. This conference contain papers on non-power applications of nuclear technology in medicine, agriculture and industry. These application include irradiation of food for disinfestation; tram technologies used in diagnosis and therapy and radiation chemistry important to industrial processes. Some technologies which evolved from the development of nuclear power industry are also discussed

  9. Device for separating, purifying and recovering nuclear fuel material, impurities and materials from impurity-containing nuclear fuel materials or nuclear fuel containing material

    International Nuclear Information System (INIS)

    Sato, Ryuichi; Kamei, Yoshinobu; Watanabe, Tsuneo; Tanaka, Shigeru.

    1988-01-01

    Purpose: To separate, purify and recover nuclear fuel materials, impurities and materials with no formation of liquid wastes. Constitution: Oxidizing atmosphere gases are introduced from both ends of a heating furnace. Vessels containing impurity-containing nuclear fuel substances or nuclear fuel substance-containing material are continuously disposed movably from one end to the other of the heating furnace. Then, impurity oxides or material oxides selectively evaporated from the impurity-containing nuclear fuel substances or nuclear fuel substance-containing materials are entrained in the oxidizing atmosphere gas and the gases are led out externally from a discharge port opened at the intermediate portion of the heating furnace, filters are disposed to the exit to solidify and capture the nuclear fuel substances and traps are disposed behind the filters to solidify and capture the oxides by spontaneous air cooling or water cooling. (Sekiya, K.)

  10. 24 CFR 598.410 - Public access to materials and proceedings.

    Science.gov (United States)

    2010-04-01

    ... DESIGNATIONS Post-Designation Requirements § 598.410 Public access to materials and proceedings. After... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Public access to materials and... Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR COMMUNITY PLANNING AND DEVELOPMENT, DEPARTMENT OF...

  11. The regulations concerning refining business of nuclear source material and nuclear fuel materials

    International Nuclear Information System (INIS)

    1979-01-01

    The regulations are provided for under the law for the regulations of nuclear source materials, nuclear fuel materials and reactors and provisions concerning refining business in the enforcement order for the law. The basic concepts and terms are defined, such as: exposure dose, accumulative dose; controlled area; inspected surrounding area and employee. Refining facilities listed in the application for designation shall be classified into clushing and leaching, thickning, refining facilities, storage facilities of nuclear source materials and nuclear fuel materials, disposal facilities of contaminated substances and building for refining, etc. Business program attached to the application shall include expected time of beginning of refining, estimated production amount of nuclear source materials or nuclear fuel materials for the first three years and funds necessary for construction, etc. Records shall be made and kept for particular periods on delivery and storage of nuclear source materials and nuclear fuel materials, control of radiation, maintenance and accidents of refining facilities. Safety securing, application of internationally regulated substances and measures in dangerous situations are stipulated respectively. Exposure dose of employees and other specified matters shall be reported by the refiner yearly to the Director General of Science and Technology Agency and the Minister of International Trade and Industry. (Okada, K.)

  12. Materials analysis with a nuclear microprobe

    International Nuclear Information System (INIS)

    Maggiore, C.J.

    1980-01-01

    The ability to produce focused beams of a few MeV light ions from Van de Graaff accelerators has resulted in the development of nuclear microprobes. Rutherford backscattering, nuclear reactions, and particle-induced x-ray emission are used to provide spatially resolved information from the near surface region of materials. Rutherford backscattering provides nondestructive depth and mass resolution. Nuclear reactions are sensitive to light elements (Z < 15). Particle-induced x-ray analysis is similar to electron microprobe analysis, but 2 orders of magnitude more sensitive. The focused beams are usually produced with specially designed multiplets of magnetic quadrupoles. The LASL microprobe uses a superconducting solenoid as a final lens. The data are acquired by a computer interfaced to the experiment with CAMAC. The characteristics of the information acquired with a nuclear microprobe are discussed; the means of producing the beams of nuclear particles are described; and the limitations and applications of such systems are given

  13. First Meeting of the Nuclear Society of Slovenia, Proceedings

    International Nuclear Information System (INIS)

    Stritar, A.; Jencic, I.

    1992-01-01

    This publication is the collection of the 38 articles from Slovenia and surrounding countries presented at the title meeting. Topics are: neutronics, thermal-hydraulic safety analysis, nuclear science and technology, probabilistic safety analysis, radioactive waste, nuclear methods and structural analysis

  14. Proceedings of the seventeenth annual Canadian Nuclear Society conference

    International Nuclear Information System (INIS)

    1996-01-01

    The seventeenth annual conference of the Canadian Nuclear Society, presented in Fredericton, New Brunswick. The conference includes papers on general topics of interest on the nuclear community, waste management and the environment, instrumentation and design of Candu reactors, safety analysis, thermal hydraulics, fuel channels, plant operations and in-core instrumentation

  15. Proceedings of the 3. nuclear science and technology conference

    International Nuclear Information System (INIS)

    1990-01-01

    Non-power applications of nuclear technology in medicine, agriculture and industry are discussed. These applications include irradiation of food for desinfestation; tram technologies used in diagnosis and therapy and radiation chemistry important to industrial processes. Some technologies which evolved from the development of the nuclear power industry are also discussed

  16. Proceedings of the seventeenth annual Canadian Nuclear Society conference

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The seventeenth annual conference of the Canadian Nuclear Society, presented in Fredericton, New Brunswick. The conference includes papers on general topics of interest on the nuclear community, waste management and the environment, instrumentation and design of Candu reactors, safety analysis, thermal hydraulics, fuel channels, plant operations and in-core instrumentation.

  17. Nuclear power risks in perspective. Proceedings of a seminar

    Energy Technology Data Exchange (ETDEWEB)

    Irvine, H S [ed.

    1981-01-01

    The objectives of this seminar were to inform the nuclear industry of the benefits and the radiological and other risks associated with the nuclear power generation fuel cycle; to compare these risks with other energy systems, other industries and life in general; to review current views on the public perception of risk; and to review methods for determining levels of risk acceptable to society.

  18. Student Scientific Conference - Nuclear Physics, 2006. Proceedings of contributions

    International Nuclear Information System (INIS)

    2006-04-01

    The conference included the following sections: (i) Applied mathematics; (ii) Didactics; (iii) Experimental physics and biophysics; (iv) Nuclear physics; (v) Theoretical physics, astronomy, meteorology and Earth physics; (vi) Mathematics; (vii) Theoretical informatics. Contributions of nuclear physics have been inputted to INIS.

  19. First Meeting of the Nuclear Society of Slovenia, Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Stritar, A; Jencic, I [Nuclear Society of Slovenia (Slovenia)

    1992-07-01

    This publication is the collection of the 38 articles from Slovenia and surrounding countries presented at the title meeting. Topics are: neutronics, thermal-hydraulic safety analysis, nuclear science and technology, probabilistic safety analysis, radioactive waste, nuclear methods and structural analysis.

  20. Proceedings of second national workshop on nuclear structure physics

    International Nuclear Information System (INIS)

    Chintalapudi, S.N.; Jain, A.K.

    1995-01-01

    The Second National Workshop on Nuclear Structure Physics was held at Calcutta during February 7-10 1995. The topics discussed have been quite broad based and covered many areas of nuclear structure physics and radiochemistry. Papers relevant to INIS are indexed separately

  1. Proceedings of the 2010 symposium on nuclear data

    International Nuclear Information System (INIS)

    Watanabe, Yukinobu; Koura, Hiroyuki; Chiba, Satoshi

    2011-09-01

    The 2010 symposium on nuclear data organized by the Nuclear Data Division of Atomic Energy Society of Japan (AESJ) was held at C-CUBE, Chikushi Campus, Kyushu University, on November 25 and 26, 2010, with approximately 60 domestic and foreign participants, in cooperation with Advanced Science Research Center of JAEA and under financial support from the Kyushu Branch of AESJ. The symposium was devoted to presentations and discussions about recent research results in a wide variety of fields associated with nuclear data, such as JENDL-4 related evaluation and benchmark tests, nuclear data measurements and facilities, theoretical model calculations, applications, and so on. A tutorial on nuclear data evaluation for actinide nuclides was given in the symposium. This report consists of total 40 papers including 15 oral presentations and 25 poster presentations. (author)

  2. Radiation damage studies of nuclear structural materials

    International Nuclear Information System (INIS)

    Barat, P.

    2012-01-01

    Maximum utilization of fuel in nuclear reactors is one of the important aspects for operating them economically. The main hindrance to achieve this higher burnups of nuclear fuel for the nuclear reactors is the possibility of the failure of the metallic core components during their operation. Thus, the study of the cause of the possibility of failure of these metallic structural materials of nuclear reactors during full power operation due to radiation damage, suffered inside the reactor core, is an important field of studies bearing the basic to industrial scientific views.The variation of the microstructure of the metallic core components of the nuclear reactors due to radiation damage causes enormous variation in the structure and mechanical properties. A firm understanding of this variation of the mechanical properties with the variation of microstructure will serve as a guide for creating new, more radiation-tolerant materials. In our centre we have irradiated structural materials of Indian nuclear reactors by charged particles from accelerator to generate radiation damage and studied the some aspects of the variation of microstructure by X-ray diffraction studies. Results achieved in this regards, will be presented. (author)

  3. Subcritical calculation of the nuclear material warehouse

    International Nuclear Information System (INIS)

    Garcia M, T.; Mazon R, R.

    2009-01-01

    In this work the subcritical calculation of the nuclear material warehouse of the Reactor TRIGA Mark III labyrinth in the Mexico Nuclear Center is presented. During the adaptation of the nuclear warehouse (vault I), the fuel was temporarily changed to the warehouse (vault II) and it was also carried out the subcritical calculation for this temporary arrangement. The code used for the calculation of the effective multiplication factor, it was the Monte Carlo N-Particle Extended code known as MCNPX, developed by the National Laboratory of Los Alamos, for the particles transport. (Author)

  4. Proceeding on the scientific meeting and presentation on basic research of nuclear science and technology (book I): physics, reactors

    International Nuclear Information System (INIS)

    Syarip; Prayitno; Samin; Agus Taftazani; Sudjatmoko; Pramudita Anggraita; Gede Sutresna W; Tjipto Sujitno; Slamet Santosa; Herry Poernomo; R Sukarsono; Prajitno

    2014-06-01

    Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is an annual activity held by Centre for Accelerator Science and Technology, National Nuclear Energy Agency, in Yogyakarta, for monitoring research activities achieved by the Agency. The papers presented in the meeting were collected into proceedings which were divided into two groups that are physics and nuclear reactors. The proceedings consists of three articles from keynote speakers and 25 articles from BATAN and others participants.(PPIKSN)

  5. Materials aspects of nuclear waste isolation

    International Nuclear Information System (INIS)

    Bennett, J.W.

    1984-01-01

    This paper is intended to provide an overview of the nuclear waste repository performance requirements and the roles which we expect materials to play in meeting these requirements. The objective of the U.S. Dept. of Energy's (DOE) program is to provide for the safe, permanent isolation of high-level radioactive wastes from the public. The Nuclear Waste Policy Act of 1982 (the Act) provides the mandate to accomplish this objective by establishing a program timetable, a schedule of procedures to be followed, and program funding (1 mil/kwhr for all nuclear generated electricity). The centerpiece of this plan is the design and operation of a mined geologic repository system for the permanent isolation of radioactive wastes. A nuclear waste repository contains several thousand acres of tunnels and drifts into which the nuclear waste will be emplaced, and several hundred acres for the facilities on the surface in which the waste is received, handled, and prepared for movement underground. With the exception of the nuclear material-related facilities, a repository is similar to a standard mining operation. The difference comes in what a repository is supposed to do - to contain an isolate nuclear waste from man and the environment

  6. Nuclear science in the 20th century. Nuclear technology applications in material science

    International Nuclear Information System (INIS)

    Pei Junchen; Xu Furong; Zheng Chunkai

    2003-01-01

    The application of nuclear technology to material science has led to a new cross subject, nuclear material science (also named nuclear solid physics) which covers material analysis, material modification and new material synthesis. This paper reviews the development of nuclear technical applications in material science and the basic physics involved

  7. Technologies for detection of nuclear materials

    International Nuclear Information System (INIS)

    DeVolpi, A.

    1996-01-01

    Detection of smuggled nuclear materials at transit points requires monitoring unknown samples in large closed packages. This review contends that high-confidence nuclear-material detection requires induced fission as the primary mechanism, with passive radiation screening in a complementary role. With the right equipment, even small quantities of nuclear materials are detectable with a high probability at transit points. The equipment could also be linked synergistically with detectors of other contrabond. For screening postal mail and packages, passive monitors are probably more cost-effective. When a suspicious item is detected, a single active probe could then be used. Until active systems become mass produced, this two-stage screening/interrogation role for active/passive equipment is more economic for cargo at border crossings. For widespread monitoring of nuclear smuggling, it will probably be necessary to develop a system for simultaneously detecting most categories of contraband, including explosives and illicit drugs. With control of nuclear materials at known storage sites being the first line of defense, detection capabilities at international borders could establish a viable second line of defense against smuggling

  8. Performance analysis of nuclear materials accounting systems

    International Nuclear Information System (INIS)

    Cobb, D.D.; Shipley, J.P.

    1979-01-01

    Techniques for analyzing the level of performance of nuclear materials accounting systems in terms of the four performance measures, total amount of loss, loss-detection time, loss-detection probability, and false-alarm probability, are presented. These techniques are especially useful for analyzing the expected performance of near-real-time (dynamic) accounting systems. A conservative estimate of system performance is provided by the CUSUM (cumulative summation of materials balances) test. Graphical displays, called performance surfaces, are developed as convenient tools for representing systems performance, and examples from a recent safeguards study of a nuclear fuels reprocessing plant are given. 6 refs

  9. Education and training in nuclear materials

    International Nuclear Information System (INIS)

    Falcon, S.; Marco, M.

    2014-01-01

    CIEMAT participates in the European project Matisse (Materials Innovations for a Safe and Sustainable nuclear in Europe) belonging to FP7, whose main objective is to promote the link between the respective national research programs through networking and integration of activities for innovation in materials for advanced nuclear systems, sharing among partners best practices and implementation of training tools and efficient communication. The draft four years, from 2013 to 2017, includes aspects such as the interaction between infrastructure, R and D programs and postgraduate education and training. (Author)

  10. Proceedings of the International Conference Nuclear Energy for New Europe 2005

    Energy Technology Data Exchange (ETDEWEB)

    Mavko, B; Kljenak, I [Nuclear Society of Slovenia (Slovenia)

    2005-07-01

    International Conference Nuclear Energy for New Europe is an annual meeting of the Nuclear Society of Slovenia. This Cd-Rom is the collection of the 139 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region presented at the title conference. Topics are: reactor physics, nuclear fusion, radiation monitoring, research and training reactors, fluid dynamics, heat and mass transfer, thermal hydraulics, safety analyses, severe accidents, nuclear materials, probabilistic safety assessment, nuclear power plant operation and monitoring, nuclear waste, public safety and environmental issues, nuclear knowledge, education and training, nuclear energy and society, advances in nuclear technology and other topics.

  11. Proceedings of the International Conference Nuclear Energy for New Europe 2005

    International Nuclear Information System (INIS)

    Mavko, B.; Kljenak, I.

    2005-01-01

    International Conference Nuclear Energy for New Europe is an annual meeting of the Nuclear Society of Slovenia. This Cd-Rom is the collection of the 139 articles from Slovenia, surrounding countries and countries of the Central and Eastern European Region presented at the title conference. Topics are: reactor physics, nuclear fusion, radiation monitoring, research and training reactors, fluid dynamics, heat and mass transfer, thermal hydraulics, safety analyses, severe accidents, nuclear materials, probabilistic safety assessment, nuclear power plant operation and monitoring, nuclear waste, public safety and environmental issues, nuclear knowledge, education and training, nuclear energy and society, advances in nuclear technology and other topics

  12. Proceedings of the 7. Workshop on Nuclear Physics

    International Nuclear Information System (INIS)

    1984-01-01

    The courses, seminaries and contributions of the 7.Work Meeting on Nuclear Physics are presented. In the courses and seminaries parts, a method to solve nuclear systems, the present stage of development of heavy ions reactions at high energies, the project and experiences for accelerators, in addition to, some important topics on tokamaks are presented. In the part of contributions, the theoretical and experimental results of reactions with light and heavy ions involving high energies, the studies of nuclear phenomena and techniques for improving instruments of radiation detection are presented. (M.C.K.) [pt

  13. Prevention of nuclear fuel cladding materials corrosion

    International Nuclear Information System (INIS)

    Yang, K.R.; Yang, J.C.; Lee, I.C.; Kang, H.D.; Cho, S.W.; Whang, C.K.

    1983-01-01

    The only way which could be performed by the operator of nuclear power plant to minimizing the degradation of nuclear fuel cladding material is to control the water quality of primary coolant as specified standard conditions which dose not attack the cladding material. If the water quality of reactor coolant does not meet far from the specification, the failure will occure not only cladding material itself but construction material of primary system which contact with the coolant. The corrosion product of system material are circulate through the whole primary system with the coolant and activated by the neutron near the reactor core. The activated corrosion products and fission products which released from fuel rod to the coolant, so called crud, will repeate deposition and redeposition continuously on the fuel rod and construction material surface. As a result we should consider heat transfer problem. In this study following activities were performed; 1. The crud sample was taken from the spent fuel rod surface of Kori unit one and analized for radioactive element and non radioactive chemical species. 2. The failure mode of nuclear fuel cladding material was estimated by the investigation of releasing type of fission products from the fuel rod to the reactor coolant using the iodine isotopes concentration of reactor coolants. 3. A study was carried out on the sipping test results of spent fuel and a discussion was made on the water quality control records through the past three cycle operation period of Kori unit one plant. (Author)

  14. Bar code usage in nuclear materials accountability

    International Nuclear Information System (INIS)

    Mee, W.T.

    1983-01-01

    The age old method of physically taking an inventory of materials by listing each item's identification number has lived beyond its usefulness. In this age of computerization, which offers the local grocery store a quick, sure, and easy means to inventory, it is time for nuclear materials facilities to automate accountability activities. The Oak Ridge Y-12 Plant began investigating the use of automated data collection devices in 1979. At that time, bar code and optical-character-recognition (OCR) systems were reviewed with the purpose of directly entering data into DYMCAS (Dynamic Special Nuclear Materials Control and Accountability System). Both of these systems appeared applicable; however, other automated devices already employed for production control made implementing the bar code and OCR seem improbable. However, the DYMCAS was placed on line for nuclear material accountability, a decision was made to consider the bar code for physical inventory listings. For the past several months a development program has been underway to use a bar code device to collect and input data to the DYMCAS on the uranium recovery operations. Programs have been completed and tested, and are being employed to ensure that data will be compatible and useful. Bar code implementation and expansion of its use for all nuclear material inventory activity in Y-12 is presented

  15. Proceedings:

    Energy Technology Data Exchange (ETDEWEB)

    Sidhu, S.S. (comp.)

    1987-12-01

    With increasingly stringent requirements on the performance of accelerators and storage rings, there is a wide interest in modeling-based control. The organizers recognized the need to have an overview and discussion on the current status of modeling-based accelerator control and how advances in computer technology, software engineering, and expert systems can impact control and diagnosis. As a result, a workshop was organized at the Brookhaven National Laboratory on August 17-18, 1987. It was made possible by the joint support of the AGS, NSLS and Applied Mathematics Departments of BNL. The talks and discussions were divided into three main topics: elements of modeling, knowledge representation, and integration of modeling-based control systems with AI and workstations. This volume is the unedited collection of papers, presented at the Workshop. Separate abstracts were prepared for 10 papers in these proceedings.

  16. Proceedings of symposium on intelligent nuclear instrumentation-2001

    International Nuclear Information System (INIS)

    Kataria, S.K.; Vaidya, P.P.; Das, Debashis; Narurkar, P.V.

    2001-02-01

    Advances in the field of instrumentation are relevant to many areas of importance such as nuclear and accelerator based research, reactor monitoring and control, non-destructive testing and evaluation, laser programme and health and environment monitoring etc. The nuclear instrumentation is a specialized field with very specific expertise in detection, processing and its analysis. The symposium covers various fields of nuclear interest such as radiation detectors, application of ASICs and FPGA in instruments, field instruments, nuclear instrumentation for basic research, accelerator, reactor, health and environmental monitoring instrumentation, medical instrumentation, instrument net working inclusive of field buses, WEB based and wireless technologies, software tools, AI technique in instrumentation etc., in this specialized area. Papers relevant to INIS are indexed separately

  17. Conference-debate 'When nuclear science provides health care' - Proceedings

    International Nuclear Information System (INIS)

    2012-03-01

    At the occasion of the 2. issue of the 'Industry week, the 'French society of nuclear energy (SFEN) young generation' and the 'Women in Nuclear (WIN)' associations have organised in partnership with Nucleopolis and the Cherbourg-Normandie Techno-pole, a conference day on the topic 'why and how nuclear energy is used for cancer therapy'. Professors Jacques Foos, Jean Datchary and Denis Agostini were invited to treat this question. This document is the compilation of their 3 presentations: 1 - The discovery, principle and medical applications of radioactivity (J. Foos, CNAM); 2 - Cancer diagnosis and therapy with nuclear medicine (D. Agostini, CHU Caen); 3 - From diagnosis to therapy: the various radiotherapy methods (J. Datchary)

  18. Proceedings of the nuclear magnetic resonance user meeting

    International Nuclear Information System (INIS)

    1987-01-01

    Studies on utilization of nuclear magnetic resonance, such as: chemical analysis in complexes and organic compounds; structures and magnetic properties of solids; construction of images and; spectrometer designs, are presented. (M.C.K.) [pt

  19. Proceedings of the 7. Brazilian Meeting on Nuclear Medicine

    International Nuclear Information System (INIS)

    1985-01-01

    Subjects about nuclear medicine are discussed. Researchs concerning the use of radioisotopes as tracers in several diseases are presented. The use of radioisotopes in diagnosis are emphasized. (M.A.C.) [pt

  20. Proceedings of the 6.Brazilian Meeting on Nuclear Medicine

    International Nuclear Information System (INIS)

    1985-01-01

    Several subjects on nuclear medicine are presented. The use of scintiscanning in heart diseases, neoplasms, etc. is emphasized. Radioisotope preparation techniques and labelling of compounds used in radioassays are described. (M.A.C.) [pt

  1. Proceedings of the 3. Brazilian Meeting on Nuclear Applications

    International Nuclear Information System (INIS)

    1995-01-01

    Researches in nuclear applications have been developed in Brazil, and were presented in this Meeting. Over 230 papers were presented in the areas of dosimetry, instrumentation, medicine, biology, agriculture, industry, radiochemistry, radiological protection, hydrology, environment and waste management

  2. New challenges in nuclear material detection

    International Nuclear Information System (INIS)

    Dunlop, W.; Sale, K.; Dougan, A.; Luke, J.; Suski, N.

    2002-01-01

    Full text: Even before the attacks of September 11, 2001 the International Safeguards community recognized the magnitude of the threat posed by illicit trafficking of nuclear materials and the need for enhanced physical protection. For the first time, separate sessions on illicit trafficking and physical protection of nuclear materials were included in the IAEA Safeguards Symposium. In the aftermath of September 11, it is clear that the magnitude of the problem and the urgency with which it must be addressed will be a significant driver for advanced nuclear materials detection technologies for years to come. Trafficking in nuclear material and other radioactive sources is a global concern. According to the IAEA Illicit Trafficking Database Program, there have been confirmed cases in more than 40 countries and the number of cases per year have nearly doubled since 1996. The challenge of combating nuclear terrorism also brings with it many opportunities for the development of new tools and new approaches. In addition to the traditional gamma-ray imaging, spectrometry and neutron interrogation, there is a need for smaller, smarter, more energy-efficient sensors and sensor systems for detecting and tracking threats. These systems go by many names - correlated sensor networks, wide-area tracking systems, sensor or network fabrics - but the concept behind them is the same. Take a number of wireless sensors and tie them together with a communications network, develop a scheme for fusing the data and make the system easy to deploy. This paper will present a brief survey of nuclear materials detection capability, and discuss some advances in research and development that are particularly suited for illicit trafficking, detection of shielded highly enriched uranium, and border security. (author)

  3. Proceedings of the symposium on advanced nuclear services

    International Nuclear Information System (INIS)

    1986-01-01

    This conference brought together representatives of Canadian nuclear power plant operators and members of private and public organizations offering services to nuclear power plant operators. The twenty papers discussed remotely operated tools and other equipment for reactor and cooling system inspection and maintenance; computer control systems; reactor simulators; improvements in the performance of pump seals, steam generators and valves; decontamination processes; and water chemistry control

  4. ICNC2003: Proceedings of the seventh international conference on nuclear criticality safety. Challenges in the pursuit of global nuclear criticality safety

    International Nuclear Information System (INIS)

    2003-10-01

    This proceedings contain (technical, oral and poster papers) presented papers at the Seventh International Conference on Nuclear Criticality Safety ICNC2003 held on 20-24 October 2003, in Tokai, Ibaraki, Japan, following ICNC'99 in Versailles, France. The theme of this conference is 'Challenges in the Pursuit of Global Nuclear Criticality Safety'. This proceedings represent the current status of nuclear criticality safety research throughout the world. The 81 of the presented papers are indexed individually. (J.P.N.)

  5. Proceedings of the Scientific Meeting and Presentation on Basic Researchin Nuclear Science and Technology part II: Nuclear Chemistry, Process Technology, Radioactive Waste Management and Environment

    International Nuclear Information System (INIS)

    Sukarsono, R.; Karmanto, Eko-Edy; Suradjijo, Ganang

    2000-01-01

    Scientific Meeting and Presentation on Basic Research in Nuclear Scienceand Technology is an annual activity held by Centre for Research and Development of Advanced Technology, National Nuclear Energy Agency, for monitoring research activities achieved by the Agency. The papers presented in the meeting were collected into proceedings. These are the second part of the proceedings that contain 71 articles in the fields of nuclear chemistry, process technology, radioactive waste management, and environment (PPIN).

  6. Proceeding of the Scientific Meeting and Presentation on Basic Research in Nuclear of the Scientific and Technology Part II : Nuclear Chemistry; Process Technology and Radioactive Waste Management; Environment

    International Nuclear Information System (INIS)

    Sudjatmoko; Karmanto, Eko Edy; Endang-Supartini

    1996-04-01

    Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is a routine activity was held by Yogyakarta Nuclear Research Centre, National Atomic Energy Agency (BATAN) for monitoring the research activity which achieved in BATAN. The Proceeding contains a proposal about basic which has Nuclear Chemistry, Process Technology, Radioactive Waste Management and Environment. This proceeding is the second part from two part which published in series. There are 61 articles which have separated index

  7. ICNC2003: Proceedings of the seventh international conference on nuclear criticality safety. Challenges in the pursuit of global nuclear criticality safety

    International Nuclear Information System (INIS)

    2003-10-01

    This proceedings contain (technical, oral and poster papers) presented papers at the Seventh International Conference on Nuclear Criticality Safety ICNC2003 held on 20-24 October 2003, in Tokai, Ibaraki, Japan, following ICNC'99 in Versailles, France. The theme of this conference is 'Challenges in the Pursuit of Global Nuclear Criticality Safety'. This proceedings represent the current status of nuclear criticality safety research throughout the world. The 79 of the presented papers are indexed individually. (J.P.N.)

  8. Nuclear techniques in the coal industry. Proceedings of a final research co-ordination meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    With the aim of promoting advanced research and facilitating a more extensive application of nuclear techniques for environmental protection in the exploration and exploitation of coal, the IAEA established the present co-ordinated research programme (CRP) in 1989. This report includes an assessment of the current status and trends in nuclear techniques in the coal industry and the results obtained by the participants at the CRP. Proceedings of the final CRP on ``Nuclear Techniques in Exploration and Exploitation of Coal: On-line and Bulk Analysis and Evaluation of Potential Environmental Pollutants in Coal and Coke``, was held in Krakow, Poland, from 9 to 12 May 1994. Refs, figs, tabs.

  9. Proceedings of the international workshop on spallation materials technology

    International Nuclear Information System (INIS)

    Mansur, L.K.; Ullmaier, H.

    1996-01-01

    This document contains papers which were presented at the International Workshop on Spallation Materials Technology. Topics included: overviews and thermal response; operational experience; materials experience; target station and component design; particle transport and damage calculations; neutron sources; and compatibility

  10. Proceedings of the international workshop on spallation materials technology

    Energy Technology Data Exchange (ETDEWEB)

    Mansur, L.K.; Ullmaier, H. [comps.

    1996-10-01

    This document contains papers which were presented at the International Workshop on Spallation Materials Technology. Topics included: overviews and thermal response; operational experience; materials experience; target station and component design; particle transport and damage calculations; neutron sources; and compatibility.

  11. CONAMET/SAM 2012. 12o.Metallurgy and materials bi national congress. Proceedings

    International Nuclear Information System (INIS)

    2012-10-01

    The publication contents are in the following areas: extractive, metals and metallic alloys, corrosion, innovation technology; ceramics, polymers, nuclear materials, composites, biomaterials, environmental aspects; nano structured materials, heat treatments, electronic and magnetic materials, quality assurance

  12. National and international nuclear material monitoring

    International Nuclear Information System (INIS)

    Waddoups, I.G.

    1996-01-01

    The status of nuclear materials in both the U.S. and Former Soviet Union is changing based upon the execution of agreements relative to weapons materials production and weapon dismantlement. The result of these activities is that a considerably different emphasis is being placed on how nuclear materials are viewed and utilized. Even though much effort is being expended on the final disposition of these materials, the interim need for storage and security of the material is increasing. Both safety and security requirements exist to govern activities when these materials are placed in storage. These requirements are intended to provide confidence that the material is not being misused and that the storage operations are conducted safely. Both of these goals can be significantly enhanced if technological monitoring of the material is performed. This paper will briefly discuss the traditional manual methods of U.S. and international material monitoring and then present approaches and technology that are available to achieve the same goals under the evolving environment

  13. Interatomic potentials for materials of nuclear interest

    International Nuclear Information System (INIS)

    Fernandez, Julian R.; Monti, Ana M.; Pasianot, Roberto C.; Simonelli, G.

    2007-01-01

    Procedures to develop embedded atom method (EAM) interatomic potentials are described, with foreseeable applications in nuclear materials. Their reliability is shown by evaluating relevant properties. The studied materials are Nb, Zr and U. The first two were then used to develop an inter species potential for the Zr-Nb binary system. In this sense, the Fe-Cu system was also studied starting from Fe and Cu potentials extracted from the literature. (author) [es

  14. Legal aspects of transport of nuclear materials

    International Nuclear Information System (INIS)

    Jacobsson, Mans.

    The Paris Convention and the Brussels Supplementary Convention are briefly discussed and other conventions in the field of civil liability for nuclear damage are mentioned: the Vienna Convention, the Nuclear Ships Convention and the 1971 Convention relating to civil liability in the field of maritime carriage of nuclear material. Legislation on civil liability in the Nordic countries, which is based on the Paris Convention and the Supplementary Convention is discussed, notably the principle of channelling of liability and exceptions from that principle due to rules of liability in older transport conventions and certain problems due to the limited geographical scope of the Paris Convention and the Supplementary Convention. Insurance problems arising in connection with transport of nuclear materials are surveyed and an outline is given of the administrative provisions concerning transport (based on the IAEA transport regulations) which govern transport of radioactive materials by different means: road, rail, sea and air. Finally, the 1968 Treaty on the Non-Proliferation of Nuclear Weapons is discussed. (NEA) [fr

  15. Proceedings of the twelfth annual conference on fossil energy materials

    International Nuclear Information System (INIS)

    Judkins, R.R.

    1998-01-01

    Papers are presented under the following session headings: ceramic composites and functional materials; ceramics, new alloys and functional materials; summary report on the workshop on materials for separation process for Vision 21 systems; and new alloys. A list of attendees is included

  16. Radiation damage in nuclear waste materials

    International Nuclear Information System (INIS)

    Jencic, I.

    2000-01-01

    Final disposal of high-level radioactive nuclear waste is usually envisioned in some sort of ceramic material. The physical and chemical properties of host materials for nuclear waste can be altered by internal radiation and consequently their structural integrity can be jeopardized. Assessment of long-term performance of these ceramic materials is therefore vital for a safe and successful disposal. This paper presents an overview of studies on several possible candidate materials for immobilization of fission products and actinides, such as spinel (MgAl 2 O 4 ), perovskite (CaTiO 3 ), zircon (ZrSiO 4 ), and pyrochlore (Gd 2 Ti 2 O 7 and Gd 2 Zr 2 O 7 ). The basic microscopic picture of radiation damage in ceramics consists of atomic displacements and ionization. In many cases these processes result in amorphization (metaminctization) of irradiated material. The evolution of microscopic structure during irradiation leads to various macroscopic radiation effects. The connection between microscopic and macroscopic picture is in most cases at least qualitatively known and studies of radiation induced microscopic changes are therefore an essential step in the design of a reliable nuclear waste host material. The relevance of these technologically important results on our general understanding of radiation damage processes and on current research efforts in Slovenia is also addressed. (author)

  17. Reliability of structural materials in nuclear industry

    International Nuclear Information System (INIS)

    Pinard Legry, G.

    1996-01-01

    The reliability of nuclear installations is a fundamental point for the exploitation of nuclear energy. It requires an extensive knowledge of the behaviour of materials in the operating conditions and during the expected service life of the installations. In nuclear power plants multiple risks of failure can exist and are expressed by corrosion and deformation phenomena or by modification in the mechanical characteristics of materials. The knowledge of the evolution with time of a given material requires to take into account the data relative to the material itself, to its environment and to the physical conditions of this environment. The study of materials aging needs a more precise knowledge of the kinetics of phenomena at any scale and of their interactions, and a micro- or macro-modeling of their behaviour during long periods of time. This paper gives an overview of the aging phenomena that occur in the structural materials involved in PWR and fast neutron reactors: thermal aging, generalized corrosion, corrosion under constraint, intergranular corrosion, crack growth under loading, wear, irradiation etc.. (J.S.)

  18. Materials technologies for advanced nuclear energy concepts

    International Nuclear Information System (INIS)

    DiStefano, J.; Harms, B.

    1983-01-01

    High-performance, advanced nuclear power plant concepts have emerged with major emphasis on lower capital costs, inherent safety, and increased reliability. The materials problems posed by these concepts are discussed and how the scientists and technologists at ORNL plan to solve them is described

  19. Proceedings of national workshop on advanced methods for materials characterization

    International Nuclear Information System (INIS)

    2004-10-01

    During the past two decades there had been tremendous growth in the field of material science and a variety of new materials with user specific properties have been developed such as smart shape memory alloys, hybrid materials like glass-ceramics, cermets, met-glasses, inorganic- organic composite layered structures, mixed oxides with negative thermal expansion, functional polymer materials etc. Study of nano-particles and the materials assembled from such particles is another area of active research being pursued all over the world. Preparation and characterization of nano-sized materials is a challenge because of their dimensions and size dependent properties. This has led to the emergence of a variety of advanced techniques, which need to be brought to the attention of the researchers working in the field of material science which requires the expertise of physics, chemistry and process engineering. This volume deals with above aspects and papers relevant to INIS are indexed separately

  20. Proceedings of the Digital Systems Reliability and Nuclear Safety Workshop

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, D. R.; Cuthill, B. B.; Ippolito, L. M. [National Inst. of Standards and Technology, Gaithersburg, MD (United States); Beltracchi, L. [Nuclear Regulatory Commission, Washington, DC (United States) ed.

    1994-03-01

    The United States Nuclear Regulatory Commission (NRC), in cooperation with the National Institute of Standards and Technology conducted the.Digital Systems Reliability and Nuclear Safety Workshop on September 13--14, 1993, in Rockville, Maryland. The workshop provided a forum for the exchange of information among experts within the nuclear industry, experts from other industries, regulators and academia. The information presented at this workshop provided in-depth exposure of the NRC staff and the nuclear industry to digital systems design safety issues and also provided feedback to the NRC from outside experts regarding identified safety issues, proposed regulatory positions, and intended research associated with the use of digital systems in nuclear power plants. Technical presentations provided insights on areas where current software engineering practices may be inadequate for safety-critical systems, on potential solutions for development issues, and on methods for reducing risk in safety-critical systems. This report contains an analysis of results of the workshop, the papers presented panel presentations, and summaries of, discussions at this workshop. The individual papers have been cataloged separately.