Device for Detection of Explosives, Nuclear and Other Hazardous Materials in Luggage and Cargo Containers

Science.gov (United States)

Kuznetsov, Andrey; Evsenin, Alexey; Gorshkov, Igor; Osetrov, Oleg; Vakhtin, Dmitry

2009-12-01

Device for detection of explosives, radioactive and heavily shielded nuclear materials in luggage and cargo containers based on Nanosecond Neutron Analysis/Associated Particles Technique (NNA/APT) is under construction. Detection module consists of a small neutron generator with built-in position-sensitive detector of associated alpha-particles, and several scintillator-based gamma-ray detectors. Explosives and other hazardous chemicals are detected by analyzing secondary high-energy gamma-rays from reactions of fast neutrons with materials inside a container. The same gamma-ray detectors are used to detect unshielded radioactive and nuclear materials. An array of several neutron detectors is used to detect fast neutrons from induced fission of nuclear materials. Coincidence and timing analysis allows one to discriminate between fission neutrons and scattered probing neutrons. Mathematical modeling by MCNP5 and MCNP-PoliMi codes was used to estimate the sensitivity of the device and its optimal configuration. Comparison of the features of three gamma detector types—based on BGO, NaI and LaBr3 crystals is presented.

The IAEA concept of detection of diversion through nuclear material accountancy (2)

International Nuclear Information System (INIS)

Akiba, Mitsunori

2005-01-01

Diversion into D (falsification of accounting report) and diversion into MUF could be detected by the Inspectorate through nuclear material accountancy. The Inspectorate designs inspection activities to detect diversion into D in cost effective ways. As a result, detection of diversion into D is divided into two statistics, one is item difference statistics which could detect major defects and the other is material balance statistics which could detect remaining small defects. MUF statistics could detect Diversion into MUF. Item statistics has many useful characteristics from safeguards view points, so it is examined in details. Material balance statistics and MUF statistics stem from measurement error associated with equipment inevitably. The above-mentioned concept is called 'IAEA decision structure'. Hereafter, designing safeguards (inspection activities) approach will be based on the IAEA decision structure. (author)

Detection of special nuclear materials with the associate particle technique

International Nuclear Information System (INIS)

Carasco, Cédric; Deyglun, Clément; Pérot, Bertrand; Eléon, Cyrille; Normand, Stéphane; Sannié, Guillaume; Boudergui, Karim; Corre, Gwenolé; Konzdrasovs, Vladimir; Pras, Philippe

2013-01-01

In the frame of the French trans-governmental R and D program against chemical, biological, radiological, nuclear and explosives (CBRN-E) threats, CEA is studying the detection of Special Nuclear Materials (SNM) by neutron interrogation with fast neutrons produced by an associated particle sealed tube neutron generator. The deuterium-tritium fusion reaction produces an alpha particle and a 14 MeV neutron almost back to back, allowing tagging neutron emission both in time and direction with an alpha particle position-sensitive sensor embedded in the generator. Fission prompt neutrons and gamma rays induced by tagged neutrons which are tagged by an alpha particle are detected in coincidence with plastic scintillators. This paper presents numerical simulations performed with the MCNP-PoliMi Monte Carlo computer code and with post processing software developed with the ROOT data analysis package. False coincidences due to neutron and photon scattering between adjacent detectors (cross talk) are filtered out to increase the selectivity between nuclear and benign materials. Accidental coincidences, which are not correlated to an alpha particle, are also taken into account in the numerical model, as well as counting statistics, and the time-energy resolution of the data acquisition system. Such realistic calculations show that relevant quantities of SNM (few kg) can be distinguished from cargo and shielding materials in 10 min acquisitions. First laboratory tests of the system under development in CEA laboratories are also presented.

Legal framework and practice to prevent and detect illicit trafficking of nuclear and radioactive materials

International Nuclear Information System (INIS)

Sembiring, D.

2001-01-01

Full text: Illicit trafficking in nuclear and radioactive materials in the country and across country borders has become serious problem from both nuclear proliferation and radiological hazard point of view. Prevention and detection of illicit trafficking in nuclear and radioactive materials is based on the regulation and procedure set up to ensure the control of the nuclear and radioactive materials throughout their life. Practically, prevention and detection measures in ensuring that nuclear materials do not become the subject of unauthorized use leading to illicit trafficking constitute (1) accounting for and (2) control of nuclear and radioactive materials and (3) physical protection of such materials. The Nuclear Energy Act No. 10 year 1997 is the legislative basis for the safety, including nuclear material accounting and control activities as well as security measures on the utilization of the nuclear and radioactive material in Indonesia. Government establishes Nuclear Energy Control Board (BAPETEN) as Regulatory Body having the task to control any activities using nuclear energy. The activities of control are implemented through regulation, licensing and inspection. The mission of the BAPETEN is to ensure adequate protection of the public health and safety, the common security, and the environmental in the peaceful uses of nuclear energy in Indonesia. To support this mission, BAPETEN has three principal regulatory functions: (1) establish regulation; (2) issue licenses and (3) inspect nuclear facilities. First component of regulatory function is establishing regulations, which define the capabilities that need to be satisfied by facility operators to protect against theft which in turn could lead to illicit trafficking. BAPETEN established the Decree on National System of Accounting for and Control of Nuclear Material (SSAC) based on the Agreement between Rl and IAEA on the Application of Safeguards in connection with NPT ratified in the Act No.8 year 1978

Novel technologies for the detection of undeclared nuclear activities, materials and facilities

Energy Technology Data Exchange (ETDEWEB)

Whichello, Julian V.K.; Annese, Cynthia E. [International Atomic Energy Agency, Vienna (Austria). Division of Technical Support

2008-07-01

This paper will discuss the International Atomic Energy Agency's (IAEA's) Novel Technologies Project and its main goal of developing improved methods and technologies that will further enhance the detection of undeclared nuclear activities, materials and facilities. A major and fundamental task within the Project has been the development of methodologies and tools for identifying, documenting and utilizing nuclear fuel cycle (NFC) indicators and signatures (I and S) to facilitate a nuclear safeguards technology gap analysis. The outcome of this work will provide a basis for a novel range of methods and instruments, the development of which will contribute to the IAEA's overall objective of enhanced detection capabilities. (author)

Advanced Laser-Compton Gamma-Ray Sources for Nuclear Materials Detection, Assay and Imaging

Science.gov (United States)

Barty, C. P. J.

2015-10-01

Highly-collimated, polarized, mono-energetic beams of tunable gamma-rays may be created via the optimized Compton scattering of pulsed lasers off of ultra-bright, relativistic electron beams. Above 2 MeV, the peak brilliance of such sources can exceed that of the world's largest synchrotrons by more than 15 orders of magnitude and can enable for the first time the efficient pursuit of nuclear science and applications with photon beams, i.e. Nuclear Photonics. Potential applications are numerous and include isotope-specific nuclear materials management, element-specific medical radiography and radiology, non-destructive, isotope-specific, material assay and imaging, precision spectroscopy of nuclear resonances and photon-induced fission. This review covers activities at the Lawrence Livermore National Laboratory related to the design and optimization of mono-energetic, laser-Compton gamma-ray systems and introduces isotope-specific nuclear materials detection and assay applications enabled by them.

Detection of smuggling of nuclear material covered by a legal transport of radioactive material

International Nuclear Information System (INIS)

Safar, J.; Zsigrai, J.; Tam, N.C.; Lakosi, L.

2001-01-01

Full text: One of the worst scenarios for detection of illicit trafficking of nuclear material is when a legal transport of radioactive material is used to cover the radiation of the smuggled uranium. Feasibility study was performed in the Institute of Isotopes and Surface Chemistry of the Chemical Research Centre of the Hungarian Academy of Sciences (hereinafter: Institute) in order to study the possible on site measurement techniques and approaches applicable in such cases. As the type A and type B packages always incorporate a feature such as a seal, in a realistic scenario the confiscated nuclear material is expected to be placed outside the package. The passive neutron emission of the uranium is negligible for a reasonable isotopic abundance therefore the feasibility study was concentrating on non-destructive, passive gamma- spectrometric methods. Possible application of Nal (diameter 40x40 mm 3 , large planar (15x15x3 mm 3 ) and a hemispheric CdZnTe (500 mm 3 , and high purity Germanium detectors was investigated. During the on site measurements portable electronics, mini multichannel analyzer, palmtop and/or notebook computer were used. The shielding material of the packages was lead or depleted uranium. The smuggled material was simulated by a package of reactor fuel pellets containing low enriched or natural uranium (materials confiscated in earlier cases) and standards containing low enriched uranium. During the supposed scenario the portal monitor provides an indication of an elevated level of the environmental radioactivity. Then the responsible (e.g. customs) officer investigate the vehicle by a hand-held survey meter in order to search for peaks in dose rates. If a peak was localized, which is different from the position of the legally transported package(s) the officer requests for the expertise of the designated institutes. The following model cases provided the basic conclusion: 1. The legal transport of the radioactive material was simulated by a

Experimental model of the device for detection of nuclear cycle materials by photoneutron technology

International Nuclear Information System (INIS)

Bakalyarov, A.M.; Karetnikov, M.D.; Kozlov, K.N.; Lebedev, V.I.; Meleshko, E.A.; Obinyakov, B.A.; Ostashev, I.E.; Tupikin, N.A.; Yakovlev, G.V.

2007-01-01

The inherent complexity of sea container control makes them potentially dangerous for smuggling nuclear materials. The experts believe that only active technologies based on recording the products of induced radiation from sensitive materials might solve the problem. The paper reports on the experimental model of the device on the basis of the electron LINAC U-28 for detection of nuclear materials by photonuclear technology. The preliminary numerical optimization of output units (converter, filter, collimator) for shaping the bremsstrahlung was carried out. The setup of experimental device and initial results of recording the prompt and delayed fission products are discussed

The German system to prevent, detect and respond to illicit uses of nuclear materials and radioactive sources

International Nuclear Information System (INIS)

Fechner, J.B.

2001-01-01

The German system to prevent, detect and respond to illicit uses of nuclear materials and radioactive sources consists of a variety of different elements: International and national laws and regulations covering safeguards, physical protection, and import/export control; Licensing and regulatory supervision of all activities related to nuclear materials and radioactive sources, including import and export; Responsibility of the licensee to ensure compliance with licensing conditions; sanctions; Law enforcement by police, security and customs authorities; prosecution and penalties; Detection of illicitly trafficked radioactive materials through intelligence and technical means; analysis capabilities; Response arrangements for normal and for severe cases of illicit use of nuclear materials; Participation in international programmes and POC-systems. Safeguards measures have been implemented in Germany in accordance with the Non- Proliferation Treaty and with safeguards agreements based on INFCIRC/153. As Germany is a member of the European Union, the Euratom Treaty and the Euratom-Ordinance Nr. 3227/76 together with the Verification Agreement between the IAEA, the European Commission and the European Member States have led to safeguards measures jointly implemented by the IAEA and by Euratom. The relevant international law for the physical protection of nuclear material in force in Germany is the Convention on the Physical Protection of Nuclear Material. The recommendations on physical protection objectives and fundamentals and on physical protection measures specified in INFCIRC/225/Rev. 4 have been taken into account in various national regulations pertaining to the national design basis threat, the physical protection of LWR nuclear power plants, of interim spent fuel storage facilities, of facilities containing category III material, of nuclear material and radioactive waste transports by road or railway vehicles, aircraft or sea vessels; additional guidelines

Advanced Ultrafast Spectroscopy for Chemical Detection of Nuclear Fuel Cycle Materials

International Nuclear Information System (INIS)

Villa-Aleman, E.; Houk, A.; Spencer, W.

2017-01-01

The development of new signatures and observables from processes related to proliferation activities are often related to the development of technologies. In our physical world, the intensity of observables is linearly related to the input drivers (light, current, voltage, etc.). Ultrafast lasers with high peak energies, opens the door to a new regime where the intensity of the observables is not necessarily linear with the laser energy. Potential nonlinear spectroscopic applications include chemical detection via remote sensing through filament generation, material characterization and processing, chemical reaction specificity, surface phenomena modifications, X-ray production, nuclear fusion, etc. The National Security Directorate laser laboratory is currently working to develop new tools for nonproliferation research with femtosecond and picosecond lasers. Prior to this project, we could only achieve laser energies in the 5 nano-Joule range, preventing the study of nonlinear phenomena. To advance our nonproliferation research into the nonlinear regime we require laser pulses in the milli-Joule (mJ) energy range. We have procured and installed a 35 fs-7 mJ laser, operating at one-kilohertz repetition rate, to investigate elemental and molecular detection of materials in the laboratory with potential applications in remote sensing. Advanced, nonlinear Raman techniques will be used to study materials of interest that are in a matrix of many materials and currently with these nonlinear techniques we can achieve greater than three orders of magnitude signal enhancement. This work studying nuclear fuel cycle materials with nonlinear spectroscopies will advance SRNL research capabilities and grow a core capability within the DOE complex.

Advanced Ultrafast Spectroscopy for Chemical Detection of Nuclear Fuel Cycle Materials

Energy Technology Data Exchange (ETDEWEB)

Villa-Aleman, E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Houk, A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Spencer, W. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-09-29

The development of new signatures and observables from processes related to proliferation activities are often related to the development of technologies. In our physical world, the intensity of observables is linearly related to the input drivers (light, current, voltage, etc.). Ultrafast lasers with high peak energies, opens the door to a new regime where the intensity of the observables is not necessarily linear with the laser energy. Potential nonlinear spectroscopic applications include chemical detection via remote sensing through filament generation, material characterization and processing, chemical reaction specificity, surface phenomena modifications, X-ray production, nuclear fusion, etc. The National Security Directorate laser laboratory is currently working to develop new tools for nonproliferation research with femtosecond and picosecond lasers. Prior to this project, we could only achieve laser energies in the 5 nano-Joule range, preventing the study of nonlinear phenomena. To advance our nonproliferation research into the nonlinear regime we require laser pulses in the milli-Joule (mJ) energy range. We have procured and installed a 35 fs-7 mJ laser, operating at one-kilohertz repetition rate, to investigate elemental and molecular detection of materials in the laboratory with potential applications in remote sensing. Advanced, nonlinear Raman techniques will be used to study materials of interest that are in a matrix of many materials and currently with these nonlinear techniques we can achieve greater than three orders of magnitude signal enhancement. This work studying nuclear fuel cycle materials with nonlinear spectroscopies will advance SRNL research capabilities and grow a core capability within the DOE complex.

Revolution in nuclear detection affairs

International Nuclear Information System (INIS)

Stern, Warren M.

2014-01-01

The detection of nuclear or radioactive materials for homeland or national security purposes is inherently difficult. This is one reason detection efforts must be seen as just one part of an overall nuclear defense strategy which includes, inter alia, material security, detection, interdiction, consequence management and recovery. Nevertheless, one could argue that there has been a revolution in detection affairs in the past several decades as the innovative application of new technology has changed the character and conduct of detection operations. This revolution will likely be most effectively reinforced in the coming decades with the networking of detectors and innovative application of anomaly detection algorithms

The nuclear materials contraband

International Nuclear Information System (INIS)

Williams, P.; Woessner, P.

1996-01-01

Several seizures of nuclear materials carried by contraband have been achieved. Some countries or criminal organizations could manufacture atomic bombs and use them. This alarming situation is described into details. Only 40% of drugs are seized by the American police and probably less in western Europe. The nuclear materials market is smaller than the drugs'one but the customs has also less experience to intercept the uranium dispatch for instance more especially as the peddlers are well organized. A severe control of the international transports would certainly allow to seize a large part of nuclear contraband materials but some dangerous isotopes as uranium 235 or plutonium 239 are little radioactive and which prevents their detection by the Geiger-Mueller counters. In France, some regulations allow to control the materials used to manufacture the nuclear weapons, and diminish thus the risk of a nuclear materials contraband. (O.L.). 4 refs., 2 figs

Detecting anomalous nuclear materials accounting transactions: Applying machine learning to plutonium processing facilities

International Nuclear Information System (INIS)

Vaccaro, H.S.

1989-01-01

Nuclear materials accountancy is the only safeguards measure that provides direct evidence of the status of nuclear materials. Of the six categories that gives rise to inventory differences, the technical capability is now in place to implement the technical innovations necessary to reduce the human error categories. There are really three main approaches to detecting anomalies in materials control and accountability (MC ampersand A) data: (1) Statistical: numeric methods such as the Page's Test, CUSUM, CUMUF, SITMUF, etc., can detect anomalies in metric (numeric) data. (2) Expert systems: Human expert's rules can be encoded into software systems such as ART, KEE, or Prolog. (3) Machine learning: Training data, such as historical MC ampersand A records, can be fed to a classifier program or neutral net or other machine learning algorithm. The Wisdom ampersand Sense (W ampersand S) software is a combination of approaches 2 and 3. The W ampersand S program includes full features for adding administrative rules and expert judgment rules to the rule base. if desired, the software can enforce consistency among all rules in the rule base

Detecting nuclear warheads

International Nuclear Information System (INIS)

Fetter, S.; Frolov, V.A.; Prilutsky, O.F.; Rodionov, S.N.; Sagdeev, R.Z.; Miller, M.

1992-01-01

To the best of our knowledge, all nuclear weapons contain at least several kilograms of fissile material - material that can sustain a chain reaction. Such material provides the energy for fission explosives such as those that destroyed Hiroshima and Nagasaki; it is also used in the fission trigger modern thermonuclear weapons. The two fissile materials used in US and Soviet warheads are weapon grade uranium (WgU) and weapon-grade plutonium (WgPu). Fissile materials are radioactive; they are very dense and absorb certain radiations very well; and they can be fissioned. This paper reports on the two basic ways to detect fissile material: passive detection of the radiation emitted by its radioactive decay, or active detection involving either radiographing (x-raying) an object with neutrons or high-energy photons and detecting particles emitted by the resulting induced fissions. Passive detection is the preferred technique for verification purposes because of its simplicity and safety

Locating sensors for detecting source-to-target patterns of special nuclear material smuggling: a spatial information theoretic approach.

Science.gov (United States)

Przybyla, Jay; Taylor, Jeffrey; Zhou, Xuesong

2010-01-01

In this paper, a spatial information-theoretic model is proposed to locate sensors for detecting source-to-target patterns of special nuclear material (SNM) smuggling. In order to ship the nuclear materials from a source location with SNM production to a target city, the smugglers must employ global and domestic logistics systems. This paper focuses on locating a limited set of fixed and mobile radiation sensors in a transportation network, with the intent to maximize the expected information gain and minimize the estimation error for the subsequent nuclear material detection stage. A Kalman filtering-based framework is adapted to assist the decision-maker in quantifying the network-wide information gain and SNM flow estimation accuracy.

Locating Sensors for Detecting Source-to-Target Patterns of Special Nuclear Material Smuggling: A Spatial Information Theoretic Approach

Directory of Open Access Journals (Sweden)

Xuesong Zhou

2010-08-01

Full Text Available In this paper, a spatial information-theoretic model is proposed to locate sensors for detecting source-to-target patterns of special nuclear material (SNM smuggling. In order to ship the nuclear materials from a source location with SNM production to a target city, the smugglers must employ global and domestic logistics systems. This paper focuses on locating a limited set of fixed and mobile radiation sensors in a transportation network, with the intent to maximize the expected information gain and minimize the estimation error for the subsequent nuclear material detection stage. A Kalman filtering-based framework is adapted to assist the decision-maker in quantifying the network-wide information gain and SNM flow estimation accuracy.

Glass fiber sensors for detecting special nuclear materials at portal and monitor stations

International Nuclear Information System (INIS)

Hull, C.D.; Seymour, R.; Crawford, T.; Bliss, M.; Craig, R.A.

2001-01-01

Nuclear Safeguards and Security Systems LLC (NucSafe) participated in the Illicit Trafficking Radiation Assessment Program (ITRAP) recently conducted by the Austrian Research Center, Seibersdorf (ARCS) for IAEA, INTERPOL, and the World Customs Organization (IAEA, in press). This presentation reviews ITRAP test results of NucSafe instrumentation. NucSafe produces stationary, mobile, and hand-held systems that use neutron and gamma ray sensors to detect Special Nuclear Materials (SNM). Neutron sensors are comprised of scintillating glass fibers (trade name 'PUMA' for Pu Materials Analysis), which provide several advantages over 3 He and 10 BF 3 tubes. PUMA 6 Li glass fiber sensors offer greater neutron sensitivity and dynamic counting range with significantly less microphonic susceptibility than tubes, while eliminating transport and operational hazards. PUMA sensors also cost less per active area than gas tubes, which is important since rapid neutron detection at passenger, freight, and vehicle portals require large sensor areas to provide the required sensitivity

Security of material: Preventing criminal activities involving nuclear and other radioactive materials

International Nuclear Information System (INIS)

Nilsson, A.

2001-01-01

The report emphasizes the need for national regulatory authorities to include in the regulatory systems, measures to control and protect nuclear materials from being used in illegal activities, as well as aspects of relevance for detecting and responding to illegal activities involving nuclear and other radioactive materials. The report will give an overview of the international treaties and agreements that underpin the establishment of a regulatory structure necessary for States to meet their non-proliferation policy and undertakings. Ongoing work to strengthen the protection of nuclear material and to detect and respond to illegal activities involving nuclear and other radioactive material will be included. The focus of the paper is on the need for standards and national regulation in the nuclear security area. (author)

IAEA coordinated research project on improvement of technical measures to detect and respond to illicit trafficking of nuclear and other radioactive materials

International Nuclear Information System (INIS)

Abedin-Zadeh, R.; Abou-Zahra, A.; Weiss, B.

2002-01-01

Full text: Monitoring to detect the illicit trafficking of nuclear and other radioactive materials includes screening vehicles, cargo and individuals at borders to 1) detect smuggling of these materials; 2) locate, measure and characterize the source of radiation; and 3) fully characterize any confiscated material. Currently available instruments used for the field measurements are not optimized for this purpose and may not detect shielded plutonium and highly enriched uranium. Confiscated radioactive materials need to be characterized with macro- and microanalysis techniques to fully understand the significance of the material and to provide credible evidence in the event of prosecution of the traffickers. Although most States have national laboratories capable to determine the basic characteristics of such material, only a few member States have the sophisticated analytical capability necessary to perform proper forensics analysis. The coordinated research project on 'Improvement of Technical Measures to Detect and Respond to Illicit Trafficking of Nuclear and other Radioactive Materials' has been established to: Improve the detection capability and performance of hand-held and portable isotope measurement devices, including the technical and functional specifications for such devices; standardize procedures to examine suspicious packages and to assess the hazard of confiscated material; and develop recommendations and guidelines for establishing a system to provide nuclear forensics support to member States for the characterization of seized nuclear material. Related to the nuclear forensics support, it should be noted that with the inception of the Agency's nuclear security programme in 1995, the IAEA has offered the services of its laboratories in Seibersdorf and associated laboratories to assist States in analysing confiscated nuclear materials. Since 1993 the IAEA has received reports of over 300 cases of smuggling of nuclear and other radioactive materials

Technique for detecting a small magnitude loss of special nuclear material

International Nuclear Information System (INIS)

Pike, D.H.; Chernick, M.R.; Downing, D.J.

The detection of losses of special nuclear materials has been the subject of much research in recent years. The standard industry practice using ID/LEID will detect large magnitude losses. Time series techniques such as the Kalman Filter or CUSUM methods will detect small magnitude losses if they occur regularly over a sustained period of time. To date no technique has been proposed which adequately addresses the problem of detecting a small magnitude loss occurring in a single period. This paper proposes a method for detecting a small magnitude loss. The approach makes use of the influence function of Hempel. The influence function measures the effect of a single inventory difference on a group of statistics. An inventory difference for a period in which a loss occurs can be expected to produce an abnormality in the calculated statistics. This abnormality is measurable by the influence function. It is shown that a one period loss smaller in magnitude than the LEID can be detected using this approach

Control of Nuclear Material in Republic of Croatia

International Nuclear Information System (INIS)

Cizmek, A.; Medakovic, S.; Prah, M.; Novosel, N.

2008-01-01

State Office for Nuclear Safety (SONS) is established based on 'Nuclear Safety Act' (Official Gazette No. 173/2003) as an independent state organization responsible for all questions in connection with safe use of nuclear energy and technology, for expert matters of preparedness in the case of nuclear emergency, as well as for international co-operation in these fields (regulatory body). In the second half of year 2006, stationary detection systems for nuclear and other radioactive materials were installed on Border Crossing Bregana, Croatia. Yantar 2U, which is the commercial name of the system, is integrated automatic system capable of detection of nuclear and other radioactive materials prepared for fixed-site customs applications (Russian origin). Installed system contains portal monitors, camera, communication lines and communication boxes and server. Two fully functional separate systems has been installed on BC Bregana, one on truck entrance and another one on car entrance. In this article the operational experience of installed system is presented. This includes statistical analysis of recorded alarms, evaluation of procedures for operational stuff and maintenance and typical malfunction experience, as well as some of the recommendation for future use of detection systems. Ordinance on the control of nuclear material and special equipment (Official Gazette No. 15/08) lays down the list of nuclear materials and special equipment as well as the list of other activities related to the production of special equipment and non-nuclear materials; the contents of the declaration of intent form for export/import of goods, the form for notifying export/import of goods, the form for notifying transport of nuclear material, the form for notifying the activity related to producing of special equipment and non-nuclear material, as well as of the form of the report on nuclear material balance in the user's material balance area. This Ordinance lays down the method of

Large area nuclear particle detectors using ET materials

International Nuclear Information System (INIS)

1987-08-01

The purpose of this SBIR Phase 1 feasibility effort was to demonstrate the usefulness of Quantex electron-trapping (ET) materials for spatial detection of nuclear particles over large areas. This demonstration entailed evaluating the prompt visible scintillation as nuclear particles impinged on films of ET materials, and subsequently detecting the nuclear particle impingement information pattern stored in the ET material, by means of the visible-wavelength luminescence produced by near-infrared interrogation. Readily useful levels of scintillation and luminescence outputs are demonstrated

Detection of special nuclear material from delayed neutron emission induced by a dual-particle monoenergetic source

Energy Technology Data Exchange (ETDEWEB)

Mayer, M. [Department of Mechanical and Nuclear Engineering, The Pennsylvania State University, University Park, Pennsylvania 16802 (United States); Nattress, J.; Jovanovic, I., E-mail: ijov@umich.edu [Department of Nuclear Engineering and Radiological Sciences, University of Michigan, Ann Arbor, Michigan 48109 (United States)

2016-06-27

Detection of unique signatures of special nuclear materials is critical for their interdiction in a variety of nuclear security and nonproliferation scenarios. We report on the observation of delayed neutrons from fission of uranium induced in dual-particle active interrogation based on the {sup 11}B(d,n γ){sup 12}C nuclear reaction. Majority of the fissions are attributed to fast fission induced by the incident quasi-monoenergetic neutrons. A Li-doped glass–polymer composite scintillation neutron detector, which displays excellent neutron/γ discrimination at low energies, was used in the measurements, along with a recoil-based liquid scintillation detector. Time-dependent buildup and decay of delayed neutron emission from {sup 238}U were measured between the interrogating beam pulses and after the interrogating beam was turned off, respectively. Characteristic buildup and decay time profiles were compared to the common parametrization into six delayed neutron groups, finding a good agreement between the measurement and nuclear data. This method is promising for detecting fissile and fissionable materials in cargo scanning applications and can be readily integrated with transmission radiography using low-energy nuclear reaction sources.

New radiological material detection technologies for nuclear forensics: Remote optical imaging and graphene-based sensors.

Energy Technology Data Exchange (ETDEWEB)

Harrison, Richard Karl [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Martin, Jeffrey B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wiemann, Dora K. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Choi, Junoh [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Howell, Stephen W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-09-01

We developed new detector technologies to identify the presence of radioactive materials for nuclear forensics applications. First, we investigated an optical radiation detection technique based on imaging nitrogen fluorescence excited by ionizing radiation. We demonstrated optical detection in air under indoor and outdoor conditions for alpha particles and gamma radiation at distances up to 75 meters. We also contributed to the development of next generation systems and concepts that could enable remote detection at distances greater than 1 km, and originated a concept that could enable daytime operation of the technique. A second area of research was the development of room-temperature graphene-based sensors for radiation detection and measurement. In this project, we observed tunable optical and charged particle detection, and developed improved devices. With further development, the advancements described in this report could enable new capabilities for nuclear forensics applications.

Detection and monitoring systems for the prevention of illicit trafficking of radioactive and nuclear materials at sea ports in EU Member States

International Nuclear Information System (INIS)

Voorbraak, W.P.; Freudenreich, W.E.; Deurwaarder, C.P.; Kaa, Th. V.D.; Carchon, R.; Baeten, P.; Bruggeman, M.; Holkamp, P.

1998-01-01

Illicit trafficking of radioactive and nuclear materials at sea ports may be considered as a serious problem. For this reason, a feasibility study has been carried out in order to investigate the detection possibilities of nuclear materials hidden in cargo which is handled at sea ports. Special attention is given to cargo packed in and transported with freight containers. Detection methods depend upon the measurement of gammas and neutrons, emitted by the nuclear material which is hidden. Detection limits of existing monitoring systems are unknown for geometrical configurations comparable to those specific at sea ports. For this reason calculations were carried out by means of the MCNP-4A Monte Carlo code in order to estimate these detection limits. These calculations are related to passive and active neutron assay, localised gamma sources and contaminated iron scrap. Results of this study are that radioactive materials can be detected without major problems. Passive neutron assay allows the detection of nuclear material in relative small quantities of plutonium in the absence of any deliberate neutron shielding, whereas in the case of dense neutron shielding, detection limits of several kilos of plutonium are obtained. A promising method appears to be a gamma- and neutron monitoring system in combination with an existing X-ray scan installation for cargo verification of container content. The detection probability is further increased when extra intelligence is applied about the origin and route of the cargo. (author)

A multisignal detection of hazardous materials for homeland security

Directory of Open Access Journals (Sweden)

Alamaniotis Miltiadis

2009-01-01

Full Text Available The detection of hazardous materials has been identified as one of the most urgent needs of homeland security, especially in scanning cargo containers at United States ports. To date, special nuclear materials have been detected using neutron or gamma interrogation, and recently the nuclear resonance fluorescence has been suggested. We show a new paradigm in detecting the materials of interest by a method that combines four signals (radiography/computer tomography, acoustic, muon scattering, and nuclear resonance fluorescence in cargos. The intelligent decision making software system is developed to support the following scenario: initially, radiography or the computer tomography scan is constructed to possibly mark the region(s of interest. The acoustic interrogation is utilized in synergy to obtain information regarding the ultrasonic velocity of the cargo interior. The superposition of the computer tomography and acoustic images narrows down the region(s of interest, and the intelligent system guides the detection to the next stage: no threat and finish, or proceed to the next interrogation. If the choice is the latter, knowing that high Z materials yield large scattering angle for muons, the muon scattering spectrum is used to detect the existence of such materials in the cargo. Additionally, the nuclear resonance fluorescence scan yields a spectrum that can be likened to the fingerprint of a material. The proposed algorithm is tested for detection of special nuclear materials in a comprehensive scenario.

A multisignal detection of hazardous materials for homeland security

International Nuclear Information System (INIS)

Alamaniotis, M.; Terrill, S.; Perry, J.; Gao, R.; Tsoukalas, L.; Jevremovic, T.

2009-01-01

The detection of hazardous materials has been identified as one of the most urgent needs of homeland security, especially in scanning cargo containers at United States ports. To date, special nuclear materials have been detected using neutron or gamma interrogation, and recently the nuclear resonance fluorescence has been suggested. We show a new paradigm in detecting the materials of interest by a method that combines four signals (radiography/computer tomography, acoustic, muon scattering, and nuclear resonance fluorescence) in cargos. The intelligent decision making software system is developed to support the following scenario: initially, radiography or the computer tomography scan is constructed to possibly mark the region(s) of interest. The acoustic interrogation is utilized in synergy to obtain information regarding the ultrasonic velocity of the cargo interior. The superposition of the computer tomography and acoustic images narrows down the region(s) of interest, and the intelligent system guides the detection to the next stage: no threat and finish, or proceed to the next interrogation. If the choice is the latter, knowing that high Z materials yield large scattering angle for muons, the muon scattering spectrum is used to detect the existence of such materials in the cargo. Additionally, the nuclear resonance fluorescence scan yields a spectrum that can be likened to the fingerprint of a material. The proposed algorithm is tested for detection of special nuclear materials in a comprehensive scenario. (author)

Radiation Detection System for Prevention of Radiological and Nuclear Terrorism

International Nuclear Information System (INIS)

Kwak, Sung-Woo; Yoo, Ho-Sik; Jang, Sung-Sun; Kim, Jae-Kwang; Kim, Jung-Soo

2007-01-01

After the September 11 terrorist attack, the threat of a potential for a radiological or nuclear terrorist attack became more apparent. The threats relating to radiological or nuclear materials include a Radiological Dispersion Device (RDD), an Improved Nuclear Device (IND) or a State Nuclear Device (such as a Soviet manufactured suitcase nuclear weapon). For more effective countermeasures against the disaster, multilayer protection concept - prevention of smuggling of radioactive or nuclear material into our country through seaports or airports, detection and prevention of the threat materials in transit on a road, and prevention of their entry into a target building - is recommended. Due to different surrounding circumstances of where detection system is deployed, different types of radiation detection systems are required. There have been no studies on characteristics of detection equipment required under Korean specific conditions. This paper provides information on technical requirements of radiation detection system to achieve multi-layer countermeasures for the purpose of protecting the public and environment against radiological and nuclear terrorism

Role of nuclear material accounting and control on nuclear security. Countermeasure against insider threat

International Nuclear Information System (INIS)

Osabe, Takeshi

2014-01-01

Possibility on unauthorized removal (theft) of nuclear material by a facility insider is a recognized as a serious threat. An insider could take advantage or knowledge of control system and access to nuclear material to intercept facility's system designed to protect theft of nuclear material by an insider. This paper will address how the facility level Nuclear Material Accounting and Control (NMAC) System should be designed and implemented to enhance deterring and detect theft of nuclear material by a facility insider. (author)

Development programs of cutting-edge technologies for measurement and detection of nuclear material for safeguards and security

International Nuclear Information System (INIS)

Seya, Michio; Wakabayashi, Shuji; Naoi, Yosuke; Ohkubo, Michiaki; Senzaki, Masao

2011-01-01

The Integrated Support Center for Nuclear Nonproliferation and Nuclear Security ('ISCN', hereafter) of Japan Atomic Energy Agency (JAEA) has development programs of cutting-edge technologies for measurement and detection of nuclear materials for nuclear safeguards and security, under the sponsorship of Japanese government (MEXT: Ministry of Education, Culture, Sports, Science and Technology). ISCN started development programs of the following technologies this year. (1) NRF (Nuclear Resonance Fluorescence) NDA technology using laser Compton scattering (LCS) gamma-rays, (2) Alternative to 3 He neutron detection technology using inorganic solid scintillator. ISCN is also going to conduct a demonstration test of a spent fuel Pu-NDA system that is to be developed by LANL (Los Alamos National Laboratory) using very sophisticated neutron measurement technologies, under JAEA/USDOE cooperation agreement. This presentation shows the above programs of ISCN. (author)

Superheated emulsions for the detection of special nuclear material

International Nuclear Information System (INIS)

D’Errico, Francesco; Di Fulvio, Angela

2011-01-01

A novel solution for the detection and smuggling interdiction of special nuclear materials is presented here consisting of large detector modules which contain superheated emulsions and which are readout with an optical approach. The detectors can be produced to be fully sensitive to prompt fission neutrons and totally insensitive to the interrogation beam, whether X-rays or neutrons below a chosen energy threshold. Therefore, the detectors are able to operate while the selected interrogation beam is on and they will only pick up the signal from fission neutrons. A position-sensitive readout mechanism is used in our design, relying on the scattering of light by neutron-induced bubbles. A beam of coherent light crosses the active area of the detector, and local variations in scattered light due to the presence of bubbles are detected in real time by arrays of silicon planar photodiodes affixed along the whole length of the detector. The system may offer a variety of advantages compared to current approaches, such as the possibility of simultaneous irradiation and detection, i.e. a 100% duty cycle, without requiring complex signal analysis, and high signal-to-noise ratio, minimizing costly nuisance alarms, thanks to its inherent insensitivity to photons.

In-field analysis and assessment of nuclear material

International Nuclear Information System (INIS)

Morgado, R.E.; Myers, W.S.; Olivares, J.A.; Phillips, J.R.; York, R.L.

1996-01-01

Los Alamos National Laboratory has actively developed and implemented a number of instruments to monitor, detect, and analyze nuclear materials in the field. Many of these technologies, developed under existing US Department of Energy programs, can also be used to effectively interdict nuclear materials smuggled across or within national borders. In particular, two instruments are suitable for immediate implementation: the NAVI-2, a hand-held gamma-ray and neutron system for the detection and rapid identification of radioactive materials, and the portable mass spectrometer for the rapid analysis of minute quantities of radioactive materials. Both instruments provide not only critical information about the characteristics of the nuclear material for law-enforcement agencies and national authorities but also supply health and safety information for personnel handling the suspect materials

Use of Nuclear Material Accounting and Control for Nuclear Security Purposes at Facilities. Implementing Guide

International Nuclear Information System (INIS)

2015-01-01

Nuclear material accounting and control (NMAC) works in a complementary fashion with the international safeguards programme and physical protection systems to help prevent, deter or detect the unauthorized acquisition and use of nuclear materials. These three methodologies are employed by Member States to defend against external threats, internal threats and both state actors and non-state actors. This publication offers guidance for implementing NMAC measures for nuclear security at the nuclear facility level. It focuses on measures to mitigate the risk posed by insider threats and describes elements of a programme that can be implemented at a nuclear facility in coordination with the physical protection system for the purpose of deterring and detecting unauthorized removal of nuclear material

Contraband Detection with Nuclear Resonance Fluorescence: Feasibility and Impact

International Nuclear Information System (INIS)

Pruet, J; Lange, D

2007-01-01

In this report they show that cargo interrogation systems developed to thwart trafficking of illicit nuclear materials could also be powerful tools in the larger fight against contraband smuggling. In particular, in addition to detecting special nuclear materials, cargo scanning systems that exploit nuclear resonance fluorescence to detect specific isotopes can be used to help find: chemical weapons; some drugs as well as some chemicals regulated under the controlled substances act; precious metals; materials regulated under export control laws; and commonly trafficked fluorocarbons

Scintilla: A New International Platform for the Development, Evaluation and Benchmarking of Technologies to Detect Radioactive and Nuclear Material

International Nuclear Information System (INIS)

Sannie, G.; Normand, S.; Peerani, P.; Tagziria, H.; Friedrich, H.; Chmel, S.; De Vita, R.; Pavan, M.; Grattarola, M.; Botta, E.; Kovacs, A.S.; Lakosi, L.; Baumhauer, C.; Equios, M.; Petrossian, G.; Picard, J.M.; Dermody, G.; Crossingham, G.

2013-06-01

For Homeland Security, enhanced detection and identification of radioactive sources and nuclear material has become of increasing importance. The scintilla project aims at minimizing the risk of radioactive sources dissemination especially with masked and shielded material. SCINTILLA offers the capacity to finding a reliable alternative to Helium-3 based detection systems since the gas which is predominantly used in nuclear safeguards and security applications has now become very expensive, rare and nearly unavailable. SCINTILLA benchmarks will be based on international standards. Radiation Portal testing being carried out at the Joint Research Centre (JRC) in Ispra (Italy). (authors)

Combating illicit trafficking in nuclear and other radioactive material. Reference material

International Nuclear Information System (INIS)

2007-01-01

This publication is intended for individuals and organizations that may be called upon to deal with the detection of and response to criminal or unauthorized acts involving nuclear or other radioactive material. It will also be useful for legislators, law enforcement agencies, government officials, technical experts, lawyers, diplomats and users of nuclear technology. This manual emphasizes the international initiatives for improving the security of nuclear and other radioactive material. However, it is recognized that effective measures for controlling the transfer of equipment, non-nuclear material, technology or information that may assist in the development of nuclear explosive devices, improvised nuclear devices (INDs) or other radiological dispersal devices (RDDs) are important elements of an effective nuclear security system. In addition, issues of personal integrity, inspection and investigative procedures are not discussed in this manual, all of which are essential elements for an effective overall security system. The manual considers a variety of elements that are recognized as being essential for dealing with incidents of criminal or unauthorized acts involving nuclear and other radioactive material. Depending on conditions in a specific State, including its legal and governmental infrastructure, some of the measures discussed will need to be adapted to suit that State's circumstances. However, much of the material can be applied directly in the context of other national programmes. This manual is divided into four main parts. Section 2 discusses the threat posed by criminal or unauthorized acts involving nuclear and other radioactive material, as well as the policy and legal bases underlying the international effort to restrain such activities. Sections 3 and 4 summarize the major international undertakings in the field. Sections 5-8 provide some basic technical information on radiation, radioactive material, the health consequences of radiation

Nuclear Material Detection by One-Short-Pulse-Laser-Driven Neutron Source

International Nuclear Information System (INIS)

Favalli, Andrea; Aymond, F.; Bridgewater, Jon S.; Croft, Stephen; Deppert, O.; Devlin, Matthew James; Falk, Katerina; Fernandez, Juan Carlos; Gautier, Donald Cort; Gonzales, Manuel A.; Goodsell, Alison Victoria; Guler, Nevzat; Hamilton, Christopher Eric; Hegelich, Bjorn Manuel; Henzlova, Daniela; Ianakiev, Kiril Dimitrov; Iliev, Metodi; Johnson, Randall Philip; Jung, Daniel; Kleinschmidt, Annika; Koehler, Katrina Elizabeth; Pomerantz, Ishay; Roth, Markus; Santi, Peter Angelo; Shimada, Tsutomu; Swinhoe, Martyn Thomas; Taddeucci, Terry Nicholas; Wurden, Glen Anthony; Palaniyappan, Sasikumar; McCary, E.

2015-01-01

Covered in the PowerPoint presentation are the following areas: Motivation and requirements for active interrogation of nuclear material; laser-driven neutron source; neutron diagnostics; active interrogation of nuclear material; and, conclusions, remarks, and future works.

Fixed-wing gamma measurement for the detection of radioactive materials

International Nuclear Information System (INIS)

Kettunen, M.J.; Nikkinen, M.T.

2005-01-01

Finland has the operational capability to take airborne gamma-ray measurements in emergency situations. The original purpose of airborne radiation mapping in Finland was to identify hazardous areas containing radioactive fall-out after a nuclear accident or use of nuclear weapons. Regular exercises are held annually to keep the operational functionality at a high level. The achieved capability has been well demonstrated in international INEX-2-FIN 1997 and Barents Rescue 2001 exercises. The knowledge and competence achieved can easily be applied in international radiation monitoring campaigns designed to expose undeclared nuclear materials or other clandestine nuclear activities. The essential improvements in the detection system are linked to the ability to locate point-like radiation sources rather than large areas of fall-out. Aerial gamma-ray measurement method and its usability for the detection of nuclear material production chains and trails of fission or activation products is described. The ability of airborne detection systems in revealing the use of undeclared nuclear materials has been tested. Various scenarios for exposing clandestine nuclear material production, enrichment and nuclear waste trails have been considered. Based on detection capability calculations and testing in practice, it was found that the detection of one un-shielded significant quantity of natural uranium (10 tons of yellow cake in storage barrels) is possible through the daughter products, using one single 6' x 4' NaI detector on the airplane. The developed fixed wing gamma measurement technique is now able to detect significant amounts of nuclear material conveniently and cost-effectively. Large areas can be screened to identify suspicious sub-areas for more detailed ground-based inspection. (author)

Passive and active correlation techniques for the detection of nuclear materials

International Nuclear Information System (INIS)

Deyglun, Clement; Carasco, Cedric; Perot, Bertrand; Eleon, Cyrille; Sannie, Guillaume; Boudergui, Karim; Corre, Gwenole; Konzdrasovs, Vladimir; Pras, Philippe

2013-06-01

In the frame of the French trans-governmental R and D program against CBRN-E threats, CEA (French Alternative Energies and Atomic Energy Commission) is studying the detection of Special Nuclear Materials (SNM) by neutron interrogation with the Associated Particle Technique (APT). Coincidences including at least 3 fission neutrons or gamma rays induced by tagged neutrons are used to detect and distinguish SNM from benign materials in which lower multiplicity events of 1 or 2 particles are produced by (n, 2n) or (n, n'γ) reactions. Coincidence are detected by fast plastic scintillators and correlated with tagged neutrons to improve the signal-to-noise ratio. Dedicated data acquisition electronics (DAQ) has been developed with independent FPGA cards associated to each detector, so that the acquisition window can be opened by any of the plastic scintillators. DAQ tests in passive mode are presented, in which acquisition is triggered by the sum signal of all detectors. The system time and energy calibration and resolution are reported, as well as the qualification of numerical simulations thanks to experimental data acquired with simple setups using a 252 Cf source. Numerical studies for the design and performance of cargo container inspection are also performed with the MCNP-PoliMi computer code and the ROOT data analysis package. SNM detection in iron cargo is quite straightforward but in organic matrix, data processing will need to combine more information to evidence SNM. (authors)

APSTNG: Neutron interrogation for detection of explosives and drugs and nuclear and CW materials

International Nuclear Information System (INIS)

Rhodes, E.; Peters, C.W.

1993-01-01

A recently developed neutron diagnostic probe system has the potential to satisfy a significant number of van-mobile and fixed-portal requirements for nondestructive detection, including monitoring of contraband explosives, drugs, and weapon materials, and treaty verification of sealed munitions. The probe is based on a unique associated-particle sealed-tube neutron generator (APSTNG) that interrogates the object of interest with a low-intensity beam of 14-MeV neutron generated from the deuterium-tritium reaction and that detects the alpha-particle associated with each neutron. Gamma-ray spectra of resulting neutron reactions identify nuclides associated with all major chemicals in explosives, drugs, and chemical warfare agents, as well as many pollutants and fissile and fertile special nuclear material. Flight times determined from detection times of the gamma rays and alpha-particles yield a separate coarse tomographic image of each identified nuclide. The APSTNG also forms the basis for a compact fast-neutron transmission imaging system that can be used along with or instead of the emission imaging system. Proof-of-concept experiments have been performed under laboratory conditions for simulated nuclear and chemical warfare munitions and for explosives and drugs. The small and relatively inexpensive APSTNG exhibits high reliability and can be quickly replaced. Surveillance systems based on APSTNG technology can avoid the large physical size, high capital and operating expenses, and reliability problems associated with complex accelerators

Improvement of equipment needed for the detection and characterization of nuclear material and radioactive samples at borders

International Nuclear Information System (INIS)

Arlt, R.; Kovar, A.; Swoboda, M.; Beck, P.; Duftschmid, K.E.; Lewis, W.

2001-01-01

Nuclear radiation measurement instruments and devices for the detection and characterisation of nuclear material and radioactive isotopes at borders play a decisive role in the set of technical measures needed to deal with the problem of illicit trafficking. Therefore the availability of a range of devices with adequate performance at affordable prices is essential. The needed equipment can be classified into the following categories: Detection equipment (border monitors and radiation pagers); Hand held devices for neutron/gamma source search and in-field characterisation of radiation sources by customs inspectors; NDA (non-destructive assay) instruments for in-depth investigation of a seized item by experts either in the field or under laboratory conditions. Instruments and techniques, which use destructive assay methods, are not considered in this paper. The most recent overview on the performance of such instruments is given in the Final Report of ITRAP (Illicit Trafficking Radiation Detection Assessment Program). According to the findings of ITRAP, although in all above mentioned categories equipment is commercially available, deficiencies and shortcomings were identified. In this paper we describe our effort in addressing some of the most essential equipment problems, identified in ITRAP - the sensitivity of border monitors with respect to the detection of nuclear material and the performance and usability of hand held and portable devices needed for in-field characterisation of seized items by customs inspectors

US develops neutron to sniff out nuclear material

CERN Document Server

2002-01-01

The USA has developed a tiny portable neutron device that can detect hidden nuclear materials. The device is undergoing trials in the Argonne National Laboratory to see if it could be used to stop smuggling and unauthorised use of nuclear weapons and materials (1/2 page).

Uncovering Special Nuclear Materials by Low-energy Nuclear Reaction Imaging.

Science.gov (United States)

Rose, P B; Erickson, A S; Mayer, M; Nattress, J; Jovanovic, I

2016-04-18

Weapons-grade uranium and plutonium could be used as nuclear explosives with extreme destructive potential. The problem of their detection, especially in standard cargo containers during transit, has been described as "searching for a needle in a haystack" because of the inherently low rate of spontaneous emission of characteristic penetrating radiation and the ease of its shielding. Currently, the only practical approach for uncovering well-shielded special nuclear materials is by use of active interrogation using an external radiation source. However, the similarity of these materials to shielding and the required radiation doses that may exceed regulatory limits prevent this method from being widely used in practice. We introduce a low-dose active detection technique, referred to as low-energy nuclear reaction imaging, which exploits the physics of interactions of multi-MeV monoenergetic photons and neutrons to simultaneously measure the material's areal density and effective atomic number, while confirming the presence of fissionable materials by observing the beta-delayed neutron emission. For the first time, we demonstrate identification and imaging of uranium with this novel technique using a simple yet robust source, setting the stage for its wide adoption in security applications.

Nuclear material control in the United States

International Nuclear Information System (INIS)

Jaeger, C.; Waddoups, I.

1995-01-01

The Department of Energy has defined a safeguards system to be an integrated system of physical protection, material accounting and material control subsystems designed to deter, prevent, detect, and respond to unauthorized possession, use, or sabotage of SNM. In practice, safeguards involve the development and application of techniques and procedures dealing with the establishment and continued maintenance of a system of activities. The system must also include administrative controls and surveillance to assure that the procedures and techniques of the system are effective and are being carried out. The control of nuclear material is critical to the safeguarding of nuclear materials within the United States. The U.S. Department of Energy includes as part of material control four functional performance areas. They include access controls, material surveillance, material containment and detection/assessment. This paper will address not only these areas but also the relationship between material control and other safeguards and security functions

Meta-material for nuclear particle detection

Science.gov (United States)

Merlo, V.; Salvato, M.; Lucci, M.; Ottaviani, I.; Cirillo, M.; Scherillo, A.; Schooneveld, E. M.; Vannozzi, A.; Celentano, G.; Pietropaolo, A.

2017-02-01

Superconducting strips coated with boron were engineered with a view to subnuclear particle detection. Combining the characteristics of boron as a generator of α-particles (as a consequence of neutron absorption) and the ability of superconducting strips to act as resistive switches, it is shown that fabricated Nb-boron and NbN-boron strips represent a promising basis for implementing neutron detection devices. In particular, the superconducting transition of boron-coated NbN strips generates voltage outputs of the order of a few volts thanks to the relatively higher normal state resitivity of NbN with respect to Nb. This result, combined with the relatively high transition temperature of NbN (of the order of 16 K for the bulk material), is an appealing prospect for future developments. The coated strips are meta-devices since their constituting material does not exist in nature and it is engineered to accomplish a specific task, i.e. generate an output voltage signal upon α-particle irradiation.

New technologies for monitoring nuclear materials

International Nuclear Information System (INIS)

Moran, B.W.

1993-01-01

This paper describes new technologies for monitoring the continued presence of nuclear materials that are being evaluated in Oak Ridge, Tennessee, to reduce the effort, cost, and employee exposures associated with conducting nuclear material inventories. These technologies also show promise for the international safeguarding of process systems and nuclear materials in storage, including spent fuels. The identified systems are based on innovative technologies that were not developed for safeguards applications. These advanced technologies include passive and active sensor systems based on optical materials, inexpensive solid-state radiation detectors, dimensional surface characterization, and digital color imagery. The passive sensor systems use specialized scintillator materials coupled to optical-fiber technologies that not only are capable of measuring radioactive emissions but also are capable of measuring or monitoring pressure, weight, temperature, and source location. Small, durable solid-state gamma-ray detection devices, whose components are estimated to cost less than $25 per unit, can be implemented in a variety of configurations and can be adapted to enhance existing monitoring systems. Variations in detector design have produced significantly different system capabilities. Dimensional surface characterization and digital color imaging are applications of developed technologies that are capable of motion detection, item surveillance, and unique identification of items

Performance analysis of nuclear materials accounting systems

International Nuclear Information System (INIS)

Cobb, D.D.; Shipley, J.P.

1979-01-01

Techniques for analyzing the level of performance of nuclear materials accounting systems in terms of the four performance measures, total amount of loss, loss-detection time, loss-detection probability, and false-alarm probability, are presented. These techniques are especially useful for analyzing the expected performance of near-real-time (dynamic) accounting systems. A conservative estimate of system performance is provided by the CUSUM (cumulative summation of materials balances) test. Graphical displays, called performance surfaces, are developed as convenient tools for representing systems performance, and examples from a recent safeguards study of a nuclear fuels reprocessing plant are given. 6 refs

The ''nuclear car wash'': a scanner to detect illicit special nuclear material in cargo containers

International Nuclear Information System (INIS)

Slaughter, D. R.; Accatino, M. R.; Bernstein, A.; Dougan, A. D.; Hall, J. M.; Loshak, A.; Manatt, D. R.; Pohl, B. A.; Prussin, S. G.; Walling, R. S.; Weirup, D. L.

2004-01-01

There is an urgent need to improve the reliability of screening cargo containers for illicit nuclear material that may be hidden there for terrorist purposes. A screening system is described for detection of fissionable material hidden in maritime cargo containers. The system makes use of a low intensity neutron beam for producing fission; and the detection of the abundant high-energy γ rays emitted in the β-decay of short-lived fission products and β-delayed neutrons. The abundance of the delayed γ rays is almost an order of magnitude larger than that of the delayed neutrons normally used to detect fission and they are emitted on about the same time scale as the delayed neutrons, i.e., ∼1 min. The energy and temporal distributions of the delayed γ rays provide a unique signature of fission. Because of their high energy, these delayed γ rays penetrate loW--Z cargoes much more readily than the delayed neutrons. Coupled with their higher abundance, the signal from the delayed γ rays escaping from the container is predicted to be as much as six decades more intense than the delayed neutron signal, depending upon the type and thickness of the intervening cargo. The γ rays are detected in a large array of scintillators located along the sides of the container as it is moved through them. Measurements have confirmed the signal strength in somewhat idealized experiments and have also identified one interference when 14.5 MeV neutrons from the D, T reaction are used for the interrogation. The interference can be removed easily by the appropriate choice of the neutron source

Scanning of vehicles for nuclear materials

International Nuclear Information System (INIS)

Katz, J. I.

2014-01-01

Might a nuclear-armed terrorist group or state use ordinary commerce to deliver a nuclear weapon by smuggling it in a cargo container or vehicle? This delivery method would be the only one available to a sub-state actor, and it might enable a state to make an unattributed attack. Detection of a weapon or fissile material smuggled in this manner is difficult because of the large volume and mass available for shielding. Here I review methods for screening cargo containers to detect the possible presence of nuclear threats. Because of the large volume of innocent international commerce, and the cost and disruption of secondary screening by opening and inspection, it is essential that the method be rapid and have a low false-positive rate. Shielding can prevent the detection of neutrons emitted spontaneously or by induced fission. The two promising methods are muon tomography and high energy X-radiography. If they do not detect a shielded threat object they can detect the shield itself

Scanning of vehicles for nuclear materials

Energy Technology Data Exchange (ETDEWEB)

Katz, J. I. [Dept. Physics and McDonnell Center for the Space Sciences, Washington University, St. Louis, MO 63130 (United States)

2014-05-09

Might a nuclear-armed terrorist group or state use ordinary commerce to deliver a nuclear weapon by smuggling it in a cargo container or vehicle? This delivery method would be the only one available to a sub-state actor, and it might enable a state to make an unattributed attack. Detection of a weapon or fissile material smuggled in this manner is difficult because of the large volume and mass available for shielding. Here I review methods for screening cargo containers to detect the possible presence of nuclear threats. Because of the large volume of innocent international commerce, and the cost and disruption of secondary screening by opening and inspection, it is essential that the method be rapid and have a low false-positive rate. Shielding can prevent the detection of neutrons emitted spontaneously or by induced fission. The two promising methods are muon tomography and high energy X-radiography. If they do not detect a shielded threat object they can detect the shield itself.

Linear filtering applied to safeguards of nuclear material

International Nuclear Information System (INIS)

Pike, D.H.; Morrison, G.W.; Holland, C.W.

1975-01-01

In regard to the problem of nuclear materials theft or diversion in the fuel cycle, a method is needed to detect continual thefts of relatively small amounts of material. It is suggested that Kalman filtering techniques be used. A hypothetical material flow situation is used to illustrate the technique; losses could be detected in as few as 5 months. (DLC)

Attributes identification of nuclear material by non-destructive radiation measurement methods

International Nuclear Information System (INIS)

Gan Lin

2002-01-01

Full text: The nuclear materials should be controlled under the regulation of National Safeguard System. The non-destructive analysis method, which is simple and quick, provide a effective process in determining the nuclear materials, nuclear scraps and wastes. The method play a very important role in the fields of nuclear material control and physical protection against the illegal removal and smuggling of nuclear material. The application of non-destructive analysis in attributes identification of nuclear material is briefly described in this paper. The attributes determined by radioactive detection technique are useful tolls to identify the characterization of special nuclear material (isotopic composition, enrichment etc.). (author)

Introduction to nuclear material safeguards

International Nuclear Information System (INIS)

Kuroi, Hideo

1986-01-01

This article is aimed at outlining the nuclear material safeguards. The International Atomic Energy Agency (IAEA) was established in 1957 and safeguards inspection was started in 1962. It is stressed that any damage resulting from nuclear proliferation would be triggered by a human intentional act. Various measures have been taken by international societies and nations, of which the safeguards are the only means which relay mainly on technical procedures. There are two modes of diversing nuclear materials to military purposes. One would be done by national intension while the other by indivisulas or expert groups, i.e., sub-national intention. IAEA is responsible for the prevention of diversification by nations, for which the international safeguards are being used. Measures against the latter mode of diversification are called nuclear protection, for which each nation is responsible. The aim of the safeguards under the Nonproliferation Treaty is to detect the diversification of a significant amount of nuclear materials from non-military purposes to production of nuclear explosion devices such as atomic weapons or to unidentified uses. Major technical methods used for the safeguards include various destructive and non-destructive tests as well as containment and monitoring techniques. System techniques are to be employed for automatic containment and monitoring procedures. Appropriate nuclear protection system techniques should also be developed. (Nogami, K.)

A Study on Current Status of Detection Technology and Establishment of National Detection Regime against Nuclear/Radiological Terrorism

International Nuclear Information System (INIS)

Kwak, Sung Woo; Jang, Sung Soon; Lee, Joung Hoon; Yoo, Ho Sik

2009-01-01

Since 1990s, some events - detection of a dirty bomb in a Russian nation park in 1995, 9/11 terrorist attack to WTC in 2001, discovery of Al-Qaeda's experimentation to build a dirty bomb in 2003 etc - have showed that nuclear or radiological terrorism relating to radioactive materials (hereinafter 'radioactive materials' is referred to as 'nuclear material, nuclear spent fuel and radioactive source') is not incredible but serious and credible threat. Thus, to respond to the new threat, the international community has not only strengthened security and physical protection of radioactive materials but also established prevention of and response to illicit trafficking of radioactive materials. In this regard, our government has enacted or revised the national regulatory framework with a view to improving security of radioactive materials and joined the international convention or agreement to meet this international trend. For the purpose of prevention of nuclear/radiological terrorism, this paper reviews physical characteristics of nuclear material and existing detection instruments used for prevention of illicit trafficking. Finally, national detection regime against nuclear/radiological terrorism based on paths of the smuggled radioactive materials to terrorist's target building/area, national topography and road networks, and defence-in-depth concept is suggested in this paper. This study should contribute to protect people's health, safety and environment from nuclear/radiological terrorism

Development of mobile radiation detection system against nuclear terrorism in Korea

International Nuclear Information System (INIS)

Kwak, Sung-Woo; Chang, Sung-Soon; Yoo, Ho-Sik

2011-01-01

A fixed radiation portal monitors (RPM) deployed at border, seaport, airport or key traffic checkpoints has played an important role in preventing the illicit trafficking and transport of nuclear and radioactive materials. However, the RPM usually is large and heavy and can't easily be moved to a different location. An intelligent terrorist may also circumvent the fixed RPM to avoid being detected. These reasons motivate us to develop a mobile radiation detection system. The objective of this paper is to report our experience on developing the mobile radiation detection system for the search and detection of nuclear and radioactive materials during road transport. Measurements were performed at various speeds and distances between the radioactive isotope (RI) transporting car and the measurement car. Results of our measurements and the detection limits of the system is described in this paper. The mobile radiation detection system developed should contribute to defending public's health and safety and the environment against nuclear and radiological terrorism by detecting nuclear or radioactive material hidden illegally in a vehicle. (author)

International survey on solid state nuclear track detection

International Nuclear Information System (INIS)

Azimi-Garakani, D.; Wernli, C.

1992-04-01

The results of the 1990 international survey on solid state nuclear track detection are presented. The survey was performed in collaboration with the International Nuclear Track Society (INTS). These results include the data on principal investigator(s), collaborator(s), institution, field of application(s), material(s), and method(s) of track observation from 28 countries. (author)

Comprehensive nuclear materials

CERN Document Server

Allen, Todd; Stoller, Roger; Yamanaka, Shinsuke

2012-01-01

Comprehensive Nuclear Materials encapsulates a panorama of fundamental information on the vast variety of materials employed in the broad field of nuclear technology. The work addresses, in five volumes, 3,400 pages and over 120 chapter-length articles, the full panorama of historical and contemporary international research in nuclear materials, from Actinides to Zirconium alloys, from the worlds' leading scientists and engineers. It synthesizes the most pertinent research to support the selection, assessment, validation and engineering of materials in extreme nuclear environments. The work discusses the major classes of materials suitable for usage in nuclear fission, fusion reactors and high power accelerators, and for diverse functions in fuels, cladding, moderator and control materials, structural, functional, and waste materials.

International safeguards: Accounting for nuclear materials

Energy Technology Data Exchange (ETDEWEB)

Fishbone, L.G.

1988-09-28

Nuclear safeguards applied by the International Atomic Energy Agency (IAEA) are one element of the non-proliferation regime'', the collection of measures whose aim is to forestall the spread of nuclear weapons to countries that do not already possess them. Safeguards verifications provide evidence that nuclear materials in peaceful use for nuclear-power production are properly accounted for. Though carried out in cooperation with nuclear facility operators, the verifications can provide assurance because they are designed with the capability to detect diversion, should it occur. Traditional safeguards verification measures conducted by inspectors of the IAEA include book auditing; counting and identifying containers of nuclear material; measuring nuclear material; photographic and video surveillance; and sealing. Novel approaches to achieve greater efficiency and effectiveness in safeguards verifications are under investigation as the number and complexity of nuclear facilities grow. These include the zone approach, which entails carrying out verifications for groups of facilities collectively, and randomization approach, which entails carrying out entire inspection visits some fraction of the time on a random basis. Both approaches show promise in particular situations, but, like traditional measures, must be tested to ensure their practical utility. These approaches are covered on this report. 15 refs., 16 figs., 3 tabs.

International safeguards: Accounting for nuclear materials

International Nuclear Information System (INIS)

Fishbone, L.G.

1988-01-01

Nuclear safeguards applied by the International Atomic Energy Agency (IAEA) are one element of the ''non-proliferation regime'', the collection of measures whose aim is to forestall the spread of nuclear weapons to countries that do not already possess them. Safeguards verifications provide evidence that nuclear materials in peaceful use for nuclear-power production are properly accounted for. Though carried out in cooperation with nuclear facility operators, the verifications can provide assurance because they are designed with the capability to detect diversion, should it occur. Traditional safeguards verification measures conducted by inspectors of the IAEA include book auditing; counting and identifying containers of nuclear material; measuring nuclear material; photographic and video surveillance; and sealing. Novel approaches to achieve greater efficiency and effectiveness in safeguards verifications are under investigation as the number and complexity of nuclear facilities grow. These include the zone approach, which entails carrying out verifications for groups of facilities collectively, and randomization approach, which entails carrying out entire inspection visits some fraction of the time on a random basis. Both approaches show promise in particular situations, but, like traditional measures, must be tested to ensure their practical utility. These approaches are covered on this report. 15 refs., 16 figs., 3 tabs

Nuclear Security Recommendations on Nuclear and Other Radioactive Material out of Regulatory Control: Recommendations

International Nuclear Information System (INIS)

2011-01-01

This publication presents recommendations for the nuclear security of nuclear and other radioactive material that is out of regulatory control. It is based on national experiences and practices and guidance publications in the field of security as well as the nuclear security related international instruments. The recommendations include guidance for States with regard to the nuclear security of nuclear and other radioactive material that has been reported as being out of regulatory control as well as for material that is lost, missing or stolen but has not been reported as such, or has been otherwise discovered. In addition, these recommendations adhere to the detection and assessment of alarms and alerts and to a graded response to criminal or unauthorized acts with nuclear security implications

Chapter No.5. Nuclear materials and physical protection of nuclear installations

International Nuclear Information System (INIS)

2002-01-01

The State System of Accounting for and Control of Nuclear Material (SSAC) is based on requirements resulting from the Safeguards Agreement between the Government of the Slovak Republic and the IAEA. UJD performs this activity according to the 'Atomic Act' and relevant decree. The purpose of the SSAC is also to prevent unauthorised use of nuclear materials, to detect loses of nuclear materials and provide information that could lead to the recovery of missing material. The main part of nuclear materials under jurisdiction of the Slovak Republic is located at NPP Jaslovske Bohunice, NPP Mochovce and at interim storage in Jaslovske Bohunice. Even though that there are located more then 99% of nuclear materials in these nuclear facilities, there are not any significant problems with their accountancy and control due to very simply identification of accountancy units - fuel assemblies, and due to stability of legal subjects responsible for operation and for keeping of information continuity, which is necessary for fulfilling requirements of the Agreement. The nuclear material located outside nuclear facilities is a special category. There are 81 such subjects of different types and orientations on the territory of the Slovak Republic. These subjects use mainly depleted uranium as a shielding and small quantity of natural uranium, low enrichment uranium and thorium for experimental purposes and education. Frequent changes of these subjects, their transformations into the other subjects, extinction and very high fluctuation of employees causes loss of information about nuclear materials and creates problems with fulfilling requirements resulting from the Agreement. In 2001, the UJD carried out 51 inspections of nuclear materials, of which 31 inspections were performed at nuclear installations in co-operation with the IAEA inspectors. No discrepancies concerning the management of nuclear materials were found out during inspections and safeguards goals in year 2001 were

Detection of radioactive materials at borders

International Nuclear Information System (INIS)

2003-08-01

By international agreements, the movement of all radioactive materials within and between States should be subject to high standards of regulatory, administrative, safety and engineering controls to ensure that such movements are conducted in a safe and secure manner. In the case of nuclear materials, there are additional requirements for physical protection and accountability to ensure against threats of nuclear proliferation and to safeguard against any attempts at diversion. The results of the terrorist attacks of September 2001 emphasized the requirement for enhanced control and security of nuclear and radioactive materials. In this regard, measures are being taken to increase the global levels of physical protection and security for nuclear materials. Experience in many parts of the world continues to prove that movements of radioactive materials outside of the regulatory and legal frameworks continue to occur. Such movements may be either deliberate or inadvertent. Deliberate, illegal movements of radioactive materials, including nuclear material, for terrorist, political or illegal profit is generally understood to be illicit trafficking. The more common movements outside of regulatory control are inadvertent in nature. An example of an inadvertent movement might be the transport of steel contaminated by a melted radioactive source that was lost from proper controls. Such a shipment may present health and safety threats to the personnel involved as well as to the general public. States have the responsibility for combating illicit trafficking and inadvertent movements of radioactive materials. The IAEA co-operates with Member States and other international organizations in joint efforts to prevent incidents of illicit trafficking and inadvertent movements and to harmonize policies and measures by the provision of relevant advice through technical assistance and documents. As an example, the IAEA and the World Customs Organization (WCO) maintain a Memorandum

Detection of radioactive materials at borders

International Nuclear Information System (INIS)

2004-05-01

By international agreements, the movement of all radioactive materials within and between States should be subject to high standards of regulatory, administrative, safety and engineering controls to ensure that such movements are conducted in a safe and secure manner. In the case of nuclear materials, there are additional requirements for physical protection and accountability to ensure against threats of nuclear proliferation and to safeguard against any attempts at diversion. The results of the terrorist attacks of September 2001 emphasized the requirement for enhanced control and security of nuclear and radioactive materials. In this regard, measures are being taken to increase the global levels of physical protection and security for nuclear materials. Experience in many parts of the world continues to prove that movements of radioactive materials outside of the regulatory and legal frameworks continue to occur. Such movements may be either deliberate or inadvertent. Deliberate, illegal movements of radioactive materials, including nuclear material, for terrorist, political or illegal profit is generally understood to be illicit trafficking. The more common movements outside of regulatory control are inadvertent in nature. An example of an inadvertent movement might be the transport of steel contaminated by a melted radioactive source that was lost from proper controls. Such a shipment may present health and safety threats to the personnel involved as well as to the general public. States have the responsibility for combating illicit trafficking and inadvertent movements of radioactive materials. The IAEA co-operates with Member States and other international organizations in joint efforts to prevent incidents of illicit trafficking and inadvertent movements and to harmonize policies and measures by the provision of relevant advice through technical assistance and documents. As an example, the IAEA and the World Customs Organization (WCO) maintain a Memorandum

Detection of radioactive materials at borders

International Nuclear Information System (INIS)

2002-09-01

By international agreements, the movement of all radioactive materials within and between States should be subject to high standards of regulatory, administrative, safety and engineering controls to ensure that such movements are conducted in a safe and secure manner. In the case of nuclear materials, there are additional requirements for physical protection and accountability to ensure against threats of nuclear proliferation and to safeguard against any attempts at diversion. The results of the terrorist attacks of September 2001 emphasized the requirement for enhanced control and security of nuclear and radioactive materials. In this regard, measures are being taken to increase the global levels of physical protection and security for nuclear materials. Experience in many parts of the world continues to prove that movements of radioactive materials outside of the regulatory and legal frameworks continue to occur. Such movements may be either deliberate or inadvertent. Deliberate, illegal movements of radioactive materials, including nuclear material, for terrorist, political or illegal profit is generally understood to be illicit trafficking. The more common movements outside of regulatory control are inadvertent in nature. An example of an inadvertent movement might be the transport of steel contaminated by a melted radioactive source that was lost from proper controls. Such a shipment may present health and safety threats to the personnel involved as well as to the general public. States have the responsibility for combating illicit trafficking and inadvertent movements of radioactive materials. The IAEA co-operates with Member States and other international organizations in joint efforts to prevent incidents of illicit trafficking and inadvertent movements and to harmonize policies and measures by the provision of relevant advice through technical assistance and documents. As an example, the IAEA and the World Customs Organization (WCO) maintain a Memorandum

Proposal of secure camera-based radiation warning system for nuclear detection

International Nuclear Information System (INIS)

Tsuchiya, Ken'ichi; Kurosawa, Kenji; Akiba, Norimitsu; Kakuda, Hidetoshi; Imoto, Daisuke; Hirabayashi, Manato; Kuroki, Kenro

2016-01-01

Counter-terrorisms against radiological and nuclear threat are significant issues toward Tokyo 2020 Olympic and Paralympic Games. In terms of cost benefit, it is not easy to build a warning system for nuclear detection to prevent a Dirty Bomb attack (dispersion of radioactive materials using a conventional explosive) or a Silent Source attack (hidden radioactive materials) from occurring. We propose a nuclear detection system using the installed secure cameras. We describe a method to estimate radiation dose from noise pattern in CCD images caused by radiation. Some dosimeters under neutron and gamma-ray irradiations (0.1mSv-100mSv) were taken in CCD video camera. We confirmed amount of noise in CCD images increased in radiation exposure. The radiation detection using CMOS in secure cameras or cell phones has been implemented. However, in this presentation, we propose a warning system including neutron detection to search shielded nuclear materials or radiation exposure devices using criticality. (author)

Integrated Global Nuclear Materials Management Preliminary Concepts

International Nuclear Information System (INIS)

Jones, E; Dreicer, M.

2006-01-01

policy, science/technology, and intelligence elements are all crucial and must be harmonized. It is envisioned that integrated solutions will include reducing and securing nuclear/radiological materials at their source; improved monitoring and tracking; and enhancing detection, interdiction, and response. An active architecture, artfully combined of many synergistic elements, would support national actions and international collaboration in nuclear materials management, and it would help navigate a transition toward global nuclear sustainability

IAEA safeguards and detection of undeclared nuclear activities

Energy Technology Data Exchange (ETDEWEB)

Harry, R.J.S.

1996-03-01

Verfication of State declarations is an essential feature of IAEA safeguards. The issue of completeness of the declaration of all nuclear material, nuclear activities and nuclear facilities arises only in full scope safeguards, like those pursuant to NPT. Concentrating on the accountability aspect of nuclear material, the NPT safeguards system has achieved a high level of objective and quantified performance. Some of the basic ideas of the drafters of INFCIRC/153 (corrected) have been stalled. Non-proliferation concerns demand also for a detection probability for undeclared nuclear activities. Following the example of the Chemical Weapon Convention (CWC), advanced detection techniques are proposed, which go beyond the classical nuclear material accountability approach. Recent proposals for additional measures to strengthen IAEA safeguards conform to rules of NPT and related safeguards. Some proposals have been agreed generally, others can only be implemented on a voluntary basis between the State and the IAEA. The implementation will require additional resources and support for the IAEA. Great care is required to maintain the existing capability of the IAEA for a technically sound, independent, objective, and internationally acceptable judgement with available resources, and at the same time to change emphasis on certain elements of the existing safeguards system. (orig.).

IAEA safeguards and detection of undeclared nuclear activities

International Nuclear Information System (INIS)

Harry, R.J.S.

1996-03-01

Verfication of State declarations is an essential feature of IAEA safeguards. The issue of completeness of the declaration of all nuclear material, nuclear activities and nuclear facilities arises only in full scope safeguards, like those pursuant to NPT. Concentrating on the accountability aspect of nuclear material, the NPT safeguards system has achieved a high level of objective and quantified performance. Some of the basic ideas of the drafters of INFCIRC/153 (corrected) have been stalled. Non-proliferation concerns demand also for a detection probability for undeclared nuclear activities. Following the example of the Chemical Weapon Convention (CWC), advanced detection techniques are proposed, which go beyond the classical nuclear material accountability approach. Recent proposals for additional measures to strengthen IAEA safeguards conform to rules of NPT and related safeguards. Some proposals have been agreed generally, others can only be implemented on a voluntary basis between the State and the IAEA. The implementation will require additional resources and support for the IAEA. Great care is required to maintain the existing capability of the IAEA for a technically sound, independent, objective, and internationally acceptable judgement with available resources, and at the same time to change emphasis on certain elements of the existing safeguards system. (orig.)

Associated-particle sealed-tube neutron probe: Detection of explosives, contraband, and nuclear materials

International Nuclear Information System (INIS)

Rhodes, E.; Dickerman, C.E.

1996-01-01

Continued research and development of the APSTNG shows the potential for practical field use of this technology for detection of explosives, contraband, and nuclear materials. The APSTNG (associated-particle sealed-tube generator) inspects the item to be examined using penetrating 14-MeV neutrons generated by the deuterium-tritium reaction inside a compact accelerator tube. An alpha detector built into the sealed tube detects the alpha-particle associated with each neutron emitted in a cone encompassing the volume to be inspected. Penetrating high-energy gamma-rays from the resulting neutron reactions identify specific nuclides inside the volume. Flight-times determined from the detection times of gamma-rays and alpha-particles separate the prompt and delayed gamma-ray spectra and allow a coarse 3-D image to be obtained of nuclides identified in the prompt spectrum. The generator and detectors can be on the same side of the inspected object, on opposite sides, or with intermediate orientations. Thus, spaces behind walls and other confined regions can be inspected. Signals from container walls can be discriminated against using the flight-time technique. No collimators or shielding are required, the neutron generator is relatively small, and commercial-grade electronics are employed. The use of 14-MeV neutrons yields a much higher cross-section for detecting nitrogen than that for systems based on thermal-neutron reactions alone, and the broad range of elements with significant 14-MeV neutron cross-sections extends explosives detection to other elements including low-nitrogen compounds, and allows detection of many other substances. Proof-of-concept experiments have been successfully performed for conventional explosives, chemical warfare agents, cocaine, and fissionable materials

Evaluating the Aspect of Nuclear Material in Fuel Cycles

Energy Technology Data Exchange (ETDEWEB)

Takagi, Shunsuke; Pickett, Susan; Oda, Takuji; Choi, Jor-Shan; Kuno, Yusuke; Takana, Satoru [Department of Nuclear Engineering and Management, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8685 (Japan); Nagasaki, Shinya [Nuclear Professional School, The University of Tokyo (Japan)

2009-06-15

The increasing number of countries that wish to introduce nuclear power plants raises attention to proliferation resistance in nuclear power plants, and nuclear fuel cycle facilities. In order to achieve adequate proliferation resistance, it is important to evaluate it and to construct effective international institutional frameworks as well as technologies involving high level of proliferation resistance. Although some methods have been proposed for evaluation of the proliferation resistance, their validities have not been investigated in detail. In the present paper, therefore, we compare some of the proposed methodologies. It is essential to detect the abuse or diversion of nuclear material before the nuclear explosive device can be manufactured in order to prevent proliferation. The time needed for the detection of material primary depends on the safeguards that the country applies, and the time needed for fabrication mainly depends on the attributes of the nuclear material. Hence, we divided the proliferation resistance into two parts: the level of safeguards and the material. For examination of evaluation methods such as the one proposed by Charlton [1] or the figure of merit (FOM) [2], sensitivity analysis was performed on weighting factors and scenarios. The validity and characteristics of each method were discussed, focusing on the applicability of each method to the assessment of multi-national approaches such as GNEP. [1] W. S. Charlton, R. L. LeBouf, C. Gariazzo, D. G. Ford, C. Beard, S. Landeberger, M. Whitaker, 'Proliferation resistance assessment methodology for nuclear fuel cycles', Nuclear Technology, 157, 1 (2007). [2] C.G. Bathke et al, 'An assessment of the proliferation resistance of materials in advanced nuclear fuel cycles', 8. International Conference on Facility Operations (2008). (authors)

Border Control of Nuclear and Other Radioactive Materials

International Nuclear Information System (INIS)

Medakovic, S.; Cizmek, A.; Prah, M.

2007-01-01

In the second half of year 2006, stationary detection systems for nuclear and other radioactive materials were installed on Border Crossing Bregana, Croatia. Yantar 2U, which is the commercial name of the system, is integrated automatic system capable of detection of nuclear and other radioactive materials prepared for fixed-site customs applications (Russian origin). Installed system contains portal monitors, camera, communication lines and communication boxes and server. Two fully functional separate systems has been installed on BC Bregana, one on truck entrance and another one on car entrance. In this article the operational experience of installed system is presented. This includes statistical analysis of recorded alarms, evaluation of procedures for operational stuff and maintenance and typical malfunction experience, as well as some of the recommendation for future use of detection systems.(author)

Device for separating, purifying and recovering nuclear fuel material, impurities and materials from impurity-containing nuclear fuel materials or nuclear fuel containing material

International Nuclear Information System (INIS)

Sato, Ryuichi; Kamei, Yoshinobu; Watanabe, Tsuneo; Tanaka, Shigeru.

1988-01-01

Purpose: To separate, purify and recover nuclear fuel materials, impurities and materials with no formation of liquid wastes. Constitution: Oxidizing atmosphere gases are introduced from both ends of a heating furnace. Vessels containing impurity-containing nuclear fuel substances or nuclear fuel substance-containing material are continuously disposed movably from one end to the other of the heating furnace. Then, impurity oxides or material oxides selectively evaporated from the impurity-containing nuclear fuel substances or nuclear fuel substance-containing materials are entrained in the oxidizing atmosphere gas and the gases are led out externally from a discharge port opened at the intermediate portion of the heating furnace, filters are disposed to the exit to solidify and capture the nuclear fuel substances and traps are disposed behind the filters to solidify and capture the oxides by spontaneous air cooling or water cooling. (Sekiya, K.)

Gamma and neutron detection modeling in the nuclear detection figure of merit (NDFOM) portal

International Nuclear Information System (INIS)

Stroud, Phillip D.; Saeger, Kevin J.

2009-01-01

The Nuclear Detection Figure Of Merit (NDFOM) portal is a database of objects and algorithms for evaluating the performance of radiation detectors to detect nuclear material. This paper describes the algorithms used to model the physics and mathematics of radiation detection. As a first-principles end-to-end analysis system, it starts with the representation of the gamma and neutron spectral fluxes, which are computed with the particle and radiation transport code MCNPX. The gamma spectra emitted by uranium, plutonium, and several other materials of interest are described. The impact of shielding and other intervening material is computed by the method of build-up factors. The interaction of radiation with the detector material is computed by a detector response function approach. The construction of detector response function matrices based on MCNPX simulation runs is described in detail. Neutron fluxes are represented in a three group formulation to treat differences in detector sensitivities to thermal, epithermal, and fast neutrons.

Radiation sensitive devices and systems for detection of radioactive materials and related methods

Science.gov (United States)

Kotter, Dale K

2014-12-02

Radiation sensitive devices include a substrate comprising a radiation sensitive material and a plurality of resonance elements coupled to the substrate. Each resonance element is configured to resonate responsive to non-ionizing incident radiation. Systems for detecting radiation from a special nuclear material include a radiation sensitive device and a sensor located remotely from the radiation sensitive device and configured to measure an output signal from the radiation sensitive device. In such systems, the radiation sensitive device includes a radiation sensitive material and a plurality of resonance elements positioned on the radiation sensitive material. Methods for detecting a presence of a special nuclear material include positioning a radiation sensitive device in a location where special nuclear materials are to be detected and remotely interrogating the radiation sensitive device with a sensor.

10 CFR 74.51 - Nuclear material control and accounting for strategic special nuclear material.

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Nuclear material control and accounting for strategic special nuclear material. 74.51 Section 74.51 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) MATERIAL CONTROL AND ACCOUNTING OF SPECIAL NUCLEAR MATERIAL Formula Quantities of Strategic Special Nuclear...

Gamma-ray identification of nuclear weapon materials

International Nuclear Information System (INIS)

Gosnell, T. B.; Hall, J. M.; Jam, C. L.; Knapp, D. A.; Koenig, Z. M.; Luke, S. J.; Pohl, B. A.; Schach Wittenau, A. von; Wolford, J. K.

1997-01-01

There has been an accelerating national interest in countering nuclear smuggling. This has caused a corresponding expansion of interest in the use of gamma-ray spectrometers for checkpoint monitoring, nuclear search, and within networks of nuclear and collateral sensors. All of these are fieldable instruments--ranging from large, fixed portal monitors to hand-held and remote monitoring equipment. For operational reasons, detectors with widely varying energy resolution and detection efficiency will be employed. In many instances, such instruments must be sensitive to weak signals, always capable of recognizing the gamma-ray signatures from nuclear weapons materials (NWM), often largely insensitive to spectral alteration by radiation transport through intervening materials, capable of real-time implementation, and able to discriminate against signals from commonly encountered legitimate gamma-ray sources, such as radiopharmaceuticals. Several decades of experience in classified programs have shown that all of these properties are not easily achieved and successful approaches were of limited scope--such as the detection of plutonium only. This project was originally planned as a two-year LDRD-ER. Since funding for 1997 was not sustained, this is a report of the first year's progress

Nuclear Security Recommendations on Nuclear and other Radioactive Material out of Regulatory Control: Recommendations (Spanish Edition)

International Nuclear Information System (INIS)

2012-01-01

This publication presents recommendations for the nuclear security of nuclear and other radioactive material that is out of regulatory control. It is based on national experiences and practices and guidance publications in the field of security as well as the nuclear security related international instruments. The recommendations include guidance for States with regard to the nuclear security of nuclear and other radioactive material that has been reported as being out of regulatory control as well as for material that is lost, missing or stolen but has not been reported as such, or has been otherwise discovered. In addition, these recommendations adhere to the detection and assessment of alarms and alerts and to a graded response to criminal or unauthorized acts with nuclear security implications.

Nuclear Security Recommendations on Nuclear and Other Radioactive Material out of Regulatory Control: Recommendations (Arabic Edition)

International Nuclear Information System (INIS)

2012-01-01

This publication presents recommendations for the nuclear security of nuclear and other radioactive material that is out of regulatory control. It is based on national experiences and practices and guidance publications in the ? field of security as well as the nuclear security related international instruments. The recommendations include guidance for States with regard to the nuclear security of nuclear and other radioactive material that has been reported as being out of regulatory control as well as for material that is lost, missing or stolen but has not been reported as such, or has been otherwise discovered. In addition, these recommendations adhere to the detection and assessment of alarms and alerts and to a graded response to criminal or unauthorized acts with nuclear security implications.

Nuclear Security Recommendations on Nuclear and Other Radioactive Material out of Regulatory Control: Recommendations (Russian Edition)

International Nuclear Information System (INIS)

2011-01-01

This publication presents recommendations for the nuclear security of nuclear and other radioactive material that is out of regulatory control. It is based on national experiences and practices and guidance publications in the field of security as well as the nuclear security related international instruments. The recommendations include guidance for States with regard to the nuclear security of nuclear and other radioactive material that has been reported as being out of regulatory control as well as for material that is lost, missing or stolen but has not been reported as such, or has been otherwise discovered. In addition, these recommendations adhere to the detection and assessment of alarms and alerts and to a graded response to criminal or unauthorized acts with nuclear security implications.

Detecting special nuclear material using muon-induced neutron emission

Energy Technology Data Exchange (ETDEWEB)

Guardincerri, Elena; Bacon, Jeffrey; Borozdin, Konstantin; Matthew Durham, J.; Fabritius II, Joseph [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Hecht, Adam [University of New Mexico, Albuquerque, NM 87131 (United States); Milner, Edward C. [Southern Methodist University, Dallas, TX 75205 (United States); Miyadera, Haruo; Morris, Christopher L. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Perry, John [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); University of New Mexico, Albuquerque, NM 87131 (United States); Poulson, Daniel [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

2015-07-21

The penetrating ability of cosmic ray muons makes them an attractive probe for imaging dense materials. Here, we describe experimental results from a new technique that uses neutrons generated by cosmic-ray muons to identify the presence of special nuclear material (SNM). Neutrons emitted from SNM are used to tag muon-induced fission events in actinides and laminography is used to form images of the stopping material. This technique allows the imaging of SNM-bearing objects tagged using muon tracking detectors located above or to the side of the objects, and may have potential applications in warhead verification scenarios. During the experiment described here we did not attempt to distinguish the type or grade of the SNM.

A portable neutron spectroscope (NSPECT) for detection, imaging and identification of nuclear material

Science.gov (United States)

Ryan, James M.; Bancroft, Christopher; Bloser, Peter; Bravar, Ulisse; Fourguette, Dominique; Frost, Colin; Larocque, Liane; McConnell, Mark L.; Legere, Jason; Pavlich, Jane; Ritter, Greg; Wassick, Greg; Wood, Joshua; Woolf, Richard

2010-08-01

We have developed, fabricated and tested a prototype imaging neutron spectrometer designed for real-time neutron source location and identification. Real-time detection and identification is important for locating materials. These materials, specifically uranium and transuranics, emit neutrons via spontaneous or induced fission. Unlike other forms of radiation (e.g. gamma rays), penetrating neutron emission is very uncommon. The instrument detects these neutrons, constructs images of the emission pattern, and reports the neutron spectrum. The device will be useful for security and proliferation deterrence, as well as for nuclear waste characterization and monitoring. The instrument is optimized for imaging and spectroscopy in the 1-20 MeV range. The detection principle is based upon multiple elastic neutron-proton scatters in organic scintillator. Two detector panel layers are utilized. By measuring the recoil proton and scattered neutron locations and energies, the direction and energy spectrum of the incident neutrons can be determined and discrete and extended sources identified. Event reconstruction yields an image of the source and its location. The hardware is low power, low mass, and rugged. Its modular design allows the user to combine multiple units for increased sensitivity. We will report the results of laboratory testing of the instrument, including exposure to a calibrated Cf-252 source. Instrument parameters include energy and angular resolution, gamma rejection, minimum source identification distances and times, and projected effective area for a fully populated instrument.

Special Nuclear Material Detection with a Water Cherenkov based Detector

International Nuclear Information System (INIS)

Sweany, M.; Bernstein, A.; Bowden, N.; Dazeley, S.; Svoboda, R.

2008-01-01

Fission events from Special Nuclear Material (SNM), such as highly enriched uranium or plutonium, produce a number of neutrons and high energy gamma-rays. Assuming the neutron multiplicity is approximately Poissonian with an average of 2 to 3, the observation of time correlations between these particles from a cargo container would constitute a robust signature of the presence of SNM inside. However, in order to be sensitive to the multiplicity, one would require a high total efficiency. There are two approaches to maximize the total efficiency; maximizing the detector efficiency or maximizing the detector solid angle coverage. The advanced detector group at LLNL is investigating one way to maximize the detector size. We are designing and building a water Cerenkov based gamma and neutron detector for the purpose of developing an efficient and cost effective way to deploy a large solid angle car wash style detector. We report on our progress in constructing a larger detector and also present preliminary results from our prototype detector that indicates detection of neutrons

Rattling nucleons: New developments in active interrogation of special nuclear material

International Nuclear Information System (INIS)

Runkle, Robert C.; Chichester, David L.; Thompson, Scott J.

2012-01-01

Active interrogation is a vigorous area of research and development due to its promise of offering detection and characterization capabilities of special nuclear material in environments where passive detection fails. The primary value added by active methods is the capability to penetrate shielding - special nuclear material itself, incidental materials, or intentional shielding - and advocates hope that active interrogation will provide a solution to the problem of detecting shielded uranium, which is at present the greatest obstacle to interdiction efforts. The technique also provides a unique benefit for quantifying nuclear material in high background-radiation environments, an area important for nuclear material safeguards and material accountancy. Progress has been made in the field of active interrogation on several fronts, most notably in the arenas of source development, systems integration, and the integration and exploitation of multiple fission and non-fission signatures. But penetration of interrogating radiation often comes at a cost, not only in terms of finance and dose but also in terms of induced backgrounds, system complexity, and extended measurement times (including set up and acquisition). These costs make the calculus for deciding to implement active interrogation more subtle than may be apparent. The purpose of this review is thus to examine existing interrogation methods, compare and contrast their attributes and limitations, and identify missions where active interrogation may hold the most promise.

Peculiarities of physical protection assurance of the nuclear materials at nuclear installation decommissioning stage

International Nuclear Information System (INIS)

Pinchuk, M.G.

2001-01-01

objective is timely prevention, detection of and response to the attempts to use accounted nuclear material for illicit trafficking. In addition to traditional measures, a centralized automated system to detect unauthorized intrusion, to register and suppress the penetration attempts and to organize controlled access to nuclear installation Chernobyl NPP and its internal areas is being established. This system covers three levels of hierarchical physical protection system of all facilities of Chernobyl NPP. The distinguishing features of this system are: high level of stability and reliability, automatic self-diagnostic functions, detection of performance intrusion and restoration of the normal operability. This system has a number of local physical protection subsystems which are the key data base users and are capable to operate off-line in case of the short-time loss of connection with the top level. The access means will include full-height turnstiles and tripods. In the areas of particular importance video identification is envisaged. Passive remote inductive cards encoded on-site will be used as passes. In addition, the issue of control, accountancy and physical protection to be exercised throughout the whole process of fuel discharge, cooling and transportation to KHOYAT -2 (interim storage facility), which will house nuclear material of the total activity more than 1.2 million Ci and about 4.00 tonnes Pu-239, is under review. It is envisaged to create complex to support nuclear material management processes. A provisional engineering solution provides for visual control and video recording, automated record of processes, casks' integrity control, communication means, blocking of the further operations when the precedent operations are inconsistent with QA program requirements, routing control and response forces notification. It shall be emphasized that so far we do not know for sure the amount of nuclear and radioactive materials inside the Shelter Object which is

Nuclear security recommendations on nuclear and other radioactive material out of regulatory control: Recommendations

International Nuclear Information System (INIS)

2011-01-01

The purpose of this publication is to provide guidance to States in strengthening their nuclear security regimes, and thereby contributing to an effective global nuclear security framework, by providing: - Recommendations to States and their competent authorities on the establishment or improvement of the capabilities of their nuclear security regimes, for carrying out effective strategies to deter, detect and respond to a criminal act, or an unauthorized act, with nuclear security implications, involving nuclear or other radioactive material that is out of regulatory control; - Recommendations to States in support of international cooperation aimed at ensuring that any nuclear or other radioactive material that is out of regulatory control, whether originating from within the State or from outside that State, is placed under regulatory control and the alleged offenders are, as appropriate, prosecuted or extradited

A grey incidence algorithm to detect high-Z material using cosmic ray muons

Science.gov (United States)

He, W.; Xiao, S.; Shuai, M.; Chen, Y.; Lan, M.; Wei, M.; An, Q.; Lai, X.

2017-10-01

Muon scattering tomography (MST) is a method for using cosmic muons to scan cargo containers and vehicles for special nuclear materials. However, the flux of cosmic ray muons is low, in the real life application, the detection has to be done a short timescale with small numbers of muons. In this paper, we present a novel approach to detection of special nuclear material by using cosmic ray muons. We use the degree of grey incidence to distinguish typical waste fuel material, uranium, from low-Z material, medium-Z material and other high-Z materials of tungsten and lead. The result shows that using this algorithm, it is possible to detect high-Z materials with an acceptable timescale.

Safeguards for special nuclear materials

International Nuclear Information System (INIS)

Carlson, R.L.

1979-12-01

Safeguards, accountability, and nuclear materials are defined. The accuracy of measuring nuclear materials is discussed. The use of computers in nuclear materials accounting is described. Measures taken to physically protect nuclear materials are described

Sample size optimization in nuclear material control. 1

International Nuclear Information System (INIS)

Gladitz, J.

1982-01-01

Equations have been derived and exemplified which allow the determination of the minimum variables sample size for given false alarm and detection probabilities of nuclear material losses and diversions, respectively. (author)

Thermodynamics of nuclear materials

International Nuclear Information System (INIS)

1979-01-01

Full text: The science of chemical thermodynamics has substantially contributed to the understanding of the many problems encountered in nuclear and reactor technology. These problems include reaction of materials with their surroundings and chemical and physical changes of fuels. Modern reactor technology, by its very nature, has offered new fields of investigations for the scientists and engineers concerned with the design of nuclear fuel elements. Moreover, thermodynamics has been vital in predicting the behaviour of new materials for fission as well as fusion reactors. In this regard, the Symposium was organized to provide a mechanism for review and discussion of recent thermodynamic investigations of nuclear materials. The Symposium was held in the Juelich Nuclear Research Centre, at the invitation of the Government of the Federal Republic of Germany. The International Atomic Energy Agency has given much attention to the thermodynamics of nuclear materials, as is evidenced by its sponsorship of four international symposia in 1962, 1965, 1967, and 1974. The first three meetings were primarily concerned with the fundamental thermodynamics of nuclear materials; as with the 1974 meeting, this last Symposium was primarily aimed at the thermodynamic behaviour of nuclear materials in actual practice, i.e., applied thermodynamics. Many advances have been made since the 1974 meeting, both in fundamental and applied thermodynamics of nuclear materials, and this meeting provided opportunities for an exchange of new information on this topic. The Symposium dealt in part with the thermodynamic analysis of nuclear materials under conditions of high temperatures and a severe radiation environment. Several sessions were devoted to the thermodynamic studies of nuclear fuels and fission and fusion reactor materials under adverse conditions. These papers and ensuing discussions provided a better understanding of the chemical behaviour of fuels and materials under these

The regulations concerning refining business of nuclear source material and nuclear fuel materials

International Nuclear Information System (INIS)

1979-01-01

The regulations are provided for under the law for the regulations of nuclear source materials, nuclear fuel materials and reactors and provisions concerning refining business in the enforcement order for the law. The basic concepts and terms are defined, such as: exposure dose, accumulative dose; controlled area; inspected surrounding area and employee. Refining facilities listed in the application for designation shall be classified into clushing and leaching, thickning, refining facilities, storage facilities of nuclear source materials and nuclear fuel materials, disposal facilities of contaminated substances and building for refining, etc. Business program attached to the application shall include expected time of beginning of refining, estimated production amount of nuclear source materials or nuclear fuel materials for the first three years and funds necessary for construction, etc. Records shall be made and kept for particular periods on delivery and storage of nuclear source materials and nuclear fuel materials, control of radiation, maintenance and accidents of refining facilities. Safety securing, application of internationally regulated substances and measures in dangerous situations are stipulated respectively. Exposure dose of employees and other specified matters shall be reported by the refiner yearly to the Director General of Science and Technology Agency and the Minister of International Trade and Industry. (Okada, K.)

Nuclear material control systems for nuclear power plants

International Nuclear Information System (INIS)

1975-06-01

Paragraph 70.51(c) of 10 CFR Part 70 requires each licensee who is authorized to possess at any one time special nuclear material in a quantity exceeding one effective kilogram to establish, maintain, and follow written material control and accounting procedures that are sufficient to enable the licensee to account for the special nuclear material in his possession under license. While other paragraphs and sections of Part 70 provide specific requirements for nuclear material control systems for fuel cycle plants, such detailed requirements are not included for nuclear power reactors. This guide identifies elements acceptable to the NRC staff for a nuclear material control system for nuclear power reactors. (U.S.)

The regulations concerning refining business of nuclear source material and nuclear fuel materials

International Nuclear Information System (INIS)

1981-01-01

This rule is established under the provisions concerning refining business in the law concerning the regulation of nuclear raw materials, nuclear fuel materials and nuclear reactors and the ordinance for the execution of this law, and to enforce them. Basic terms are defined, such as: exposure radiation dose, cumulative dose, control area, surrounding monitoring area and worker. The application for the designation for refining business under the law shall be classified into the facilities for crushing and leaching-filtration, thikening, and refining, the storage facilities for nuclear raw materials and nuclear fuel materials, and the disposal facilities for radioactive wastes, etc. To the application, shall be attached business plans, the explanations concerning the technical abilities of applicants and the prevention of hazards by nuclear raw materials and nuclear fuel materials regarding refining facilities, etc. Records shall be made on the accept, delivery and stock of each kind of nuclear raw materials and nuclear fuel materials, radiation control, the maintenance of and accidents in refining facilities, and kept for specified periods, respectively. Security regulations shall be enacted for each works or enterprise on the functions and organizations of persons engaged in the control of refining facilities, the operation of the apparatuses which must be controlled for the prevention of accidents, and the establishment of control area and surrounding monitoring area, etc. The report on the usage of internationally regulated goods and the measures taken at the time of danger are defined particularly. (Okada, K.)

Limits of Tumor Detectability in Nuclear Medicine and PET

Directory of Open Access Journals (Sweden)

Yusuf Emre Erdi

2012-04-01

Full Text Available Objective: Nuclear medicine is becoming increasingly important in the early detection of malignancy. The advantage of nuclear medicine over other imaging modalities is the high sensitivity of the gamma camera. Nuclear medicine counting equipment has the capability of detecting levels of radioactivity which exceed background levels by as little as 2.4 to 1. This translates to only a few hundred counts per minute on a regular gamma camera or as few as 3 counts per minute when using coincidence detection on a positron emission tomography (PET camera. Material and Methods: We have experimentally measured the limits of detectability using a set of hollow spheres in a Jaszczak phantom at various tumor-to-background ratios. Imaging modalities for this work were (1 planar, (2 SPECT, (3 PET, and (4 planar camera with coincidence detection capability (MCD. Results: When there is no background (infinite contrast activity present, the detectability of tumors is similar for PET and planar imaging. With the presence of the background activity , PET can detect objects in an order of magnitude smaller in size than that can be seen by conventional planar imaging especially in the typical clinical low (3:1 T/B ratios. The detection capability of the MCD camera lies between a conventional nuclear medicine (planar / SPECT scans and the detection capability of a dedicated PET scanner Conclusion: Among nuclear medicine’s armamentarium, PET is the closest modality to CT or MR imaging in terms of limits of detection. Modern clinical PET scanners have a resolution limit of 4 mm, corresponding to the detection of tumors with a volume of 0.2 ml (7 mm diameter in 5:1 T/B ratio. It is also possible to obtain better resolution limits with dedicated brain and animal scanners. The future holds promise in development of new detector materials, improved camera design, and new reconstruction algorithms which will improve sensitivity, resolution, contrast, and thereby further

Applications of Kalman Filtering to nuclear material control. [Kalman filtering and linear smoothing for detecting nuclear material losses

Energy Technology Data Exchange (ETDEWEB)

Pike, D.H.; Morrison, G.W.; Westley, G.W.

1977-10-01

The feasibility of using modern state estimation techniques (specifically Kalman Filtering and Linear Smoothing) to detect losses of material from material balance areas is evaluated. It is shown that state estimation techniques are not only feasible but in most situations are superior to existing methods of analysis. The various techniques compared include Kalman Filtering, linear smoothing, standard control charts, and average cumulative summation (CUSUM) charts. Analysis results indicated that the standard control chart is the least effective method for detecting regularly occurring losses. An improvement in the detection capability over the standard control chart can be realized by use of the CUSUM chart. Even more sensitivity in the ability to detect losses can be realized by use of the Kalman Filter and the linear smoother. It was found that the error-covariance matrix can be used to establish limits of error for state estimates. It is shown that state estimation techniques represent a feasible and desirable method of theft detection. The technique is usually more sensitive than the CUSUM chart in detecting losses. One kind of loss which is difficult to detect using state estimation techniques is a single isolated loss. State estimation procedures are predicated on dynamic models and are well-suited for detecting losses which occur regularly over several accounting periods. A single isolated loss does not conform to this basic assumption and is more difficult to detect.

CVD diamond for nuclear detection applications

International Nuclear Information System (INIS)

Bergonzo, P.; Brambilla, A.; Tromson, D.; Mer, C.; Guizard, B.; Marshall, R.D.; Foulon, F.

2002-01-01

Chemically vapour deposited (CVD) diamond is a remarkable material for the fabrication of radiation detectors. In fact, there exist several applications where other standard semiconductor detectors do not fulfil the specific requirements imposed by corrosive, hot and/or high radiation dose environments. The improvement of the electronic properties of CVD diamond has been under intensive investigations and led to the development of a few applications that are addressing specific industrial needs. Here, we report on CVD diamond-based detector developments and we describe how this material, even though of a polycrystalline nature, is readily of great interest for applications in the nuclear industry as well as for physics experiments. Improvements in the material synthesis as well as on device fabrication especially concern the synthesis of films that do not exhibit space charge build up effects which are often encountered in CVD diamond materials and that are highly detrimental for detection devices. On a pre-industrial basis, CVD diamond detectors have been fabricated for nuclear industry applications in hostile environments. Such devices can operate in harsh environments and overcome limitations encountered with the standard semiconductor materials. Of these, this paper presents devices for the monitoring of the alpha activity in corrosive nuclear waste solutions, such as those encountered in nuclear fuel assembly reprocessing facilities, as well as diamond-based thermal neutron detectors exhibiting a high neutron to gamma selectivity. All these demonstrate the effectiveness of a demanding industrial need that relies on the remarkable resilience of CVD diamond

10 CFR 74.41 - Nuclear material control and accounting for special nuclear material of moderate strategic...

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Nuclear material control and accounting for special nuclear material of moderate strategic significance. 74.41 Section 74.41 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) MATERIAL CONTROL AND ACCOUNTING OF SPECIAL NUCLEAR MATERIAL Special Nuclear Material...

The Science of Nuclear Materials: A Modular, Laboratory-based Curriculum

Energy Technology Data Exchange (ETDEWEB)

Cahill, C.L., E-mail: cahill@gwu.edu [Department of Chemistry and Elliott School of International Affairs, The George Washington University, Washington, DC 20052 (United States); Feldman, G.; Briscoe, W.J. [Department of Physics, The George Washington University, Washington, DC 20052 (United States)

2014-06-15

The development of a curriculum for nuclear materials courses targeting students pursuing Master of Arts degrees at The George Washington University is described. The courses include basic concepts such as radiation and radioactivity as well as more complex topics such the nuclear fuel cycle, nuclear weapons, radiation detection and technological aspects of non-proliferation.

The Science of Nuclear Materials: A Modular, Laboratory-based Curriculum

International Nuclear Information System (INIS)

Cahill, C.L.; Feldman, G.; Briscoe, W.J.

2014-01-01

The development of a curriculum for nuclear materials courses targeting students pursuing Master of Arts degrees at The George Washington University is described. The courses include basic concepts such as radiation and radioactivity as well as more complex topics such the nuclear fuel cycle, nuclear weapons, radiation detection and technological aspects of non-proliferation

Microchannel plate special nuclear materials sensor

International Nuclear Information System (INIS)

Feller, W.B.; White, P.L.; White, P.B.; Siegmund, O.H.W.; Martin, A.P.; Vallerga, J.V.

2011-01-01

Nova Scientific Inc., is developing for the Domestic Nuclear Detection Office (DNDO SBIR no. HSHQDC-08-C-00190), a solid-state, high-efficiency neutron detection alternative to 3 He gas tubes, using neutron-sensitive microchannel plates (MCPs) containing 10 B and/or Gd. This work directly supports DNDO development of technologies designed to detect and interdict nuclear weapons or illicit nuclear materials. Neutron-sensitized MCPs have been shown theoretically and more recently experimentally, to be capable of thermal neutron detection efficiencies equivalent to 3 He gas tubes. Although typical solid-state neutron detectors typically have an intrinsic gamma sensitivity orders of magnitude higher than that of 3 He gas detectors, we dramatically reduce gamma sensitivity by combining a novel electronic coincidence rejection scheme, employing a separate but enveloping gamma scintillator. This has already resulted in a measured gamma rejection ratio equal to a small 3 He tube, without in principle sacrificing neutron detection efficiency. Ongoing improvements to the MCP performance as well as the coincidence counting geometry will be described. Repeated testing and validation with a 252 Cf source has been underway throughout the Phase II SBIR program, with ongoing comparisons to a small commercial 3 He gas tube. Finally, further component improvements and efforts toward integration maturity are underway, with the goal of establishing functional prototypes for SNM field testing.

Improvement of technical measures to detect and respond to illicit trafficking of nuclear and radioactive materials [Results of a coordinated research project 2003-2006

International Nuclear Information System (INIS)

2008-07-01

This publication summarizes the research conducted during an IAEA Coordinated Research Project (CRP) undertaken to address technical and operational difficulties in the detection of and response to illicit trafficking of nuclear material. Equipment to detect illicit trafficking of nuclear and radioactive materials at borders has specific technical and operational requirements that are very different from equipment used in other radiation monitoring cases. Automated and manual measurements need to be done in the field, often outdoors, at land or sea borders, crossing points or airports. The free flow of goods and passengers must not be impacted, thus requiring that the measurement time be short. The design needs to take into account that the users of the equipment are not experts in radiation detection; thus the results of the measurements should be easy to understand

A sensitive detector to prevent smuggling of nuclear material

International Nuclear Information System (INIS)

Bock, H.; Rost, R.; Miller, B.R.

1995-01-01

A drive through detector systems using four plastic scintillators and associated electronics for the detections of small amounts or uranium or plutonium in cars is described. The system has been calibrated with various sample of special nuclear material and the lower detection limits are presented. (author)

Induced-Fission Imaging of Nuclear Material

International Nuclear Information System (INIS)

Hausladen, Paul; Blackston, Matthew A.; Mullens, James Allen; McConchie, Seth M.; Mihalczo, John T.; Bingham, Philip R.; Ericson, Milton Nance; Fabris, Lorenzo

2010-01-01

This paper presents initial results from development of the induced-fission imaging technique, which can be used for the purpose of measuring or verifying the distribution of fissionable material in an unopened container. The technique is based on stimulating fissions in nuclear material with 14 MeV neutrons from an associated-particle deuterium-tritium (D-T) generator and counting the subsequent induced fast fission neutrons with an array of fast organic scintillation detectors. For each source neutron incident on the container, the neutron creation time and initial trajectory are known from detection of the associated alpha particle of the d + t → α + n reaction. Many induced fissions will lie along (or near) the interrogating neutron path, allowing an image of the spatial distribution of prompt induced fissions, and thereby fissionable material, to be constructed. A variety of induced-fission imaging measurements have been performed at Oak Ridge National Laboratory with a portable, low-dose D-T generator, including single-view radiographic measurements and three-dimensional tomographic measurements. Results from these measurements will be presented along with the neutron transmission images that have been performed simultaneously. This new capability may have applications to a number of areas in which there may be a need to confirm the presence or configuration of nuclear materials, such as nuclear material control and accountability, quality assurance, treaty confirmation, or homeland security applications.

Nuclear reaction analysis (NRA) for trace element detection

Energy Technology Data Exchange (ETDEWEB)

Doebeli, M. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Noll, K. [Bern Univ. (Switzerland)

1997-09-01

Ion beam induced nuclear reactions can be used to analyse trace element concentrations in materials. The method is especially suited for the detection of light contaminants in heavy matrices. (author) 3 figs., 2 refs.

Application of nuclear-physics methods in space materials science

Science.gov (United States)

Novikov, L. S.; Voronina, E. N.; Galanina, L. I.; Chirskaya, N. P.

2017-07-01

The brief history of the development of investigations at the Skobeltsyn Institute of Nuclear Physics, Moscow State University (SINP MSU) in the field of space materials science is outlined. A generalized scheme of a numerical simulation of the radiation impact on spacecraft materials and elements of spacecraft equipment is examined. The results obtained by solving some of the most important problems that modern space materials science should address in studying nuclear processes, the interaction of charged particles with matter, particle detection, the protection from ionizing radiation, and the impact of particles on nanostructures and nanomaterials are presented.

Investigation of Active Interrogation Techniques to Detect Special Nuclear Material in Maritime Environments

International Nuclear Information System (INIS)

Miller, Thomas Martin; Patton, Bruce W.

2010-01-01

The detection and interdiction of special nuclear material (SNM) is still a high-priority focus area for many organizations around the world. One method that is commonly considered a leading candidate in the detection of SNM is active interrogation (AI). AI is different from its close relative, passive interrogation, in that an active source is used to enhance or create a detectable signal (usually fission) from SNM, particularly in shielded scenarios or scenarios where the SNM has a low activity. The use of AI thus makes the detection of SNM easier or, in some scenarios, even enables previously impossible detection. In this work the signal from prompt neutrons and photons as well as delayed neutrons and photons will be combined, as is typically done in AI. In previous work AI has been evaluated experimentally and computationally. However, for the purposes of this work, past scenarios are considered lightly shielded and tightly coupled spatially. At most, the previous work interrogated the contents of one standard cargo container (2.44 x 2.60 x 6.10 m) and the source and detector were both within a few meters of the object being interrogated. A few examples of this type of previous work can be found in references 1 and 2. Obviously, more heavily shielded AI scenarios will require larger source intensities, larger detector surface areas (larger detectors or more detectors), greater detector efficiencies, longer count times, or some combination of these.

Challenges in ensuring radiological safety and nuclear forensic for malicious acts involving nuclear and other radioactive material

International Nuclear Information System (INIS)

Sharma, Ranjit; Chatterjee, M.K.; Singh, Rajvir; Pradeepkumar, K.S.

2010-01-01

Nuclear and other radioactive materials may get smuggled into the country aimed at malicious acts. Radioactive material detected accidentally or during inspection at the entry points/national borders may indicate illicit trafficking for the purpose of nuclear/radiological terrorism. As country requires prevention and preparedness for response to these malicious acts, nuclear forensic techniques are to be developed incorporating radiological safety aspects. Nuclear forensics helps in determining the origin, intended use, legal owner and the smuggled route etc. by using fingerprinting as well as comparison with reference data. The suggested sequence of methods for analysis of radioactive material/samples will be radiological assessment, physical characterization, traditional forensic analysis, isotope analysis along with elemental/chemical analysis

A saddle-point for data verification and materials accountancy to control nuclear material

International Nuclear Information System (INIS)

Beedgen, R.

1983-01-01

Materials accountancy is one of the main elements in international safeguards to determine whether or not nuclear material has been diverted in nuclear plants. The inspector makes independent measurements to verify the plant-operator's data before closing the materials balance with the operator's data. All inspection statements are in principle probability statements because of random errors in measuring the material and verification on a random sampling basis. Statistical test procedures help the inspector to decide under this uncertainty. In this paper a statistical test procedure representing a saddle-point is presented that leads to the highest guaranteed detection probability taking all concealing strategies into account. There are arguments favoring a separate statistical evaluation of data verification and materials accountancy. Following these considerations, a bivariate test procedure is explained that evaluates verification and accountancy separately. (orig.) [de

Auditing nuclear materials statements

International Nuclear Information System (INIS)

Anon.

1973-01-01

A standard that may be used as a guide for persons making independent examinations of nuclear materials statements or reports regarding inventory quantities on hand, receipts, production, shipment, losses, etc. is presented. The objective of the examination of nuclear materials statements by the independent auditor is the expression of an opinion on the fairness with which the statements present the nuclear materials position of a nuclear materials facility and the movement of such inventory materials for the period under review. The opinion is based upon an examination made in accordance with auditing criteria, including an evaluation of internal control, a test of recorded transactions, and a review of measured discards and materials unaccounted for (MUF). The standard draws heavily upon financial auditing standards and procedures published by the American Institute of Certified Public Accountants

Detection of radioactive materials at Astrakhan

International Nuclear Information System (INIS)

Cantut, L.; Dougan, A.; Hemberger, P.; Kravenchenko, Gromov A..; Martin, D.; Pohl, B.; Richardson, J. H.; Williams, H.; York, R.; Zaitsev, E.

1999-01-01

Astrakhan is the major Russian port on the Caspian Sea. Consequently, it is the node for significant river traffic up the Volga, as well as shipments to and from other seaports on the Caspian Sea. The majority of this latter trade across the Caspian Sea is with Iran. The Second Line of Defense and RF SCC identified Astrakhan as one of the top priorities for upgrading with modern radiation detection equipment. The purpose of the cooperative effort between RF SCC and DOE at Astrakhan is to provide the capability through equipment and training to monitor and detect illegal shipments of nuclear materials through Astrakhan. The first facility was equipped with vehicle and rail portal monitoring systems. The second facility was equipped with pedestrian, vehicle and rail portal monitoring systems. A second phase of this project will complete the equipping of Astrakhan by providing additional rail and handheld systems, along with completion of video systems. Associated with both phases is the necessary equipment and procedural training to ensure successful operation of the equipment in order to detect and deter illegal trafficking in nuclear materials. The presentation will described this project and its overall relationship to the Second Line of Defense Program

Protection and control of nuclear materials

International Nuclear Information System (INIS)

Jalouneix, J.; Winter, D.

2007-01-01

In the framework of the French regulation on nuclear materials possession, the first liability is the one of operators who have to know at any time the quantity, quality and localization of any nuclear material in their possession. This requires an organization of the follow up and of the inventory of these materials together with an efficient protection against theft or sabotage. The French organization foresees a control of the implementation of this regulation at nuclear facilities and during the transport of nuclear materials by the minister of industry with the sustain of the institute of radiation protection and nuclear safety (IRSN). This article presents this organization: 1 - protection against malevolence; 2 - national protection and control of nuclear materials: goals, administrative organization, legal and regulatory content (authorization, control, sanctions), nuclear materials protection inside facilities (physical protection, follow up and inventory, security studies), protection of nuclear material transports (physical protection, follow up), control of nuclear materials (inspection at facilities, control of nuclear material measurements, inspection of nuclear materials during transport); 3 - international commitments of France: non-proliferation treaty, EURATOM regulation, international convention on the physical protection of nuclear materials, enforcement in France. (J.S.)

Combining item and bulk material loss-detection uncertainties

International Nuclear Information System (INIS)

Eggers, R.F.

1982-01-01

Loss detection requirements, such as five formula kilograms with 99% probability of detection, which apply to the sum of losses from material in both item and bulk form, constitute a special problem for the nuclear material statistician. Requirements of this type are included in the Material Control and Accounting Reform Amendments described in the Advance Notice of Proposed Rule Making (Federal Register, 46(175):45144-46151). Attribute test sampling of items is the method used to detect gross defects in the inventory of items in a given control unit. Attribute sampling plans are designed to detect a loss of a specificed goal quantity of material with a given probability. In contrast to the methods and statistical models used for item loss detection, bulk material loss detection requires all the material entering and leaving a control unit to be measured and the calculation of a loss estimator that will be tested against an appropriate alarm threshold. The alarm threshold is determined from an estimate of the error inherent in the components of the loss estimator. In this paper a simple grahical method of evaluating the combined capabilities of bulk material loss detection methods and item attribute testing procedures will be described. Quantitative results will be given for several cases, indicating how a decrease in the precision of the item loss detection method tends to force an increase in the precision of the bulk loss detection procedure in order to meet the overall detection requirement. 4 figures

Defense Nuclear Material Stewardship Integrated Inventory Information Management System (IIIMS).

Energy Technology Data Exchange (ETDEWEB)

Aas, Christopher A.; Lenhart, James E.; Bray, Olin H.; Witcher, Christina Jenkin

2004-11-01

Sandia National Laboratories was tasked with developing the Defense Nuclear Material Stewardship Integrated Inventory Information Management System (IIIMS) with the sponsorship of NA-125.3 and the concurrence of DOE/NNSA field and area offices. The purpose of IIIMS was to modernize nuclear materials management information systems at the enterprise level. Projects over the course of several years attempted to spearhead this modernization. The scope of IIIMS was broken into broad enterprise-oriented materials management and materials forecasting. The IIIMS prototype was developed to allow multiple participating user groups to explore nuclear material requirements and needs in detail. The purpose of material forecasting was to determine nuclear material availability over a 10 to 15 year period in light of the dynamic nature of nuclear materials management. Formal DOE Directives (requirements) were needed to direct IIIMS efforts but were never issued and the project has been halted. When restarted, duplicating or re-engineering the activities from 1999 to 2003 is unnecessary, and in fact future initiatives can build on previous work. IIIMS requirements should be structured to provide high confidence that discrepancies are detected, and classified information is not divulged. Enterprise-wide materials management systems maintained by the military can be used as overall models to base IIIMS implementation concepts upon.

Control of Nuclear Materials and Special Equipment (Nuclear Safety Regulations)

International Nuclear Information System (INIS)

Cizmek, A.; Prah, M.; Medakovic, S.; Ilijas, B.

2008-01-01

Based on Nuclear Safety Act (OG 173/03) the State Office for Nuclear Safety (SONS) in 2008 adopted beside Ordinance on performing nuclear activities (OG 74/06) and Ordinance on special conditions for individual activities to be performed by expert organizations which perform activities in the area of nuclear safety (OG 74/06) the new Ordinance on the control of nuclear material and special equipment (OG 15/08). Ordinance on the control of nuclear material and special equipment lays down the list of nuclear materials and special equipment as well as of nuclear activities covered by the system of control of production of special equipment and non-nuclear material, the procedure for notifying the intention to and filing the application for a license to carry out nuclear activities, and the format and contents of the forms for doing so. This Ordinance also lays down the manner in which nuclear material records have to be kept, the procedure for notifying the State administration organization (regulatory body) responsible for nuclear safety by the nuclear material user, and the keeping of registers of nuclear activities, nuclear material and special equipment by the State administration organization (regulatory body) responsible for nuclear safety, as well as the form and content of official nuclear safety inspector identification card and badge.(author)

Device for detecting defective nuclear reactor fuel rods

International Nuclear Information System (INIS)

Steven, J.

1976-01-01

A moisture sensor is provided for a nuclear fuel rod for water-cooled nuclear reactors wherein moisture can be present. The fuel rod has an end cap and a charge of nuclear fuel. The moisture sensor is disposed between the end cap and the charge and serves to detect a leak in the fuel rod. The moisture sensor includes a capsule-like housing having an inner space and having openings through which moisture can pass into the inner space in the event of a leak in the fuel rod. Ferromagnetic material is disposed in the inner space of the housing together with a moisture detector responsive to moisture for altering the diposition of the ferromagnetic material in the inner space. 5 claims, 6 drawing figures

Illicit diversion of nuclear materials

International Nuclear Information System (INIS)

Bett, F.L.

1975-08-01

This paper discusses the means of preventing illegal use of nuclear material by terrorists or other sub-national groups and by governments. With respect to sub-national groups, it concludes that the preventive measures of national safeguards systems, when taken together with the practical difficulties of using nuclear material, would make the diversion and illegal use of nuclear material unattractive in comparison with other avenues open to these groups to attain their ends. It notes that there are only certain areas in the nuclear fuel cycle, e.g. production of some types of nuclear fuel embodying highly enriched uranium and shipment of strategically significant nuclear material, which contain material potentially useful to these groups. It also discusses the difficult practical problems, e.g. coping with radiation, which would face the groups in making use of the materials for terrorist purposes. Concerning illegal use by Governments, the paper describes the role of international safeguards, as applied by the International Atomic Energy Agency, and the real deterrent effect of these safeguards which is achieved through the requirements to maintain comprehensive operating records of the use of nuclear material and by regular inspections to verify these records. The paper makes the point that Australia would not consider supplying nuclear material unless it were subject to international safeguards. (author)

Physics and technology of nuclear materials

International Nuclear Information System (INIS)

Ursu, I.

1985-01-01

The subject is covered in chapters, entitled; elements of nuclear reactor physics; structure and properties of materials (including radiation effects); fuel materials (uranium, plutonium, thorium); structural materials (including - aluminium, zirconium, stainless steels, ferritic steels, magnesium alloys, neutron irradiation induced changes in the mechanical properties of structural materials); moderator materials (including - nuclear graphite, natural (light) water, heavy water, beryllium, metal hydrides); materials for reactor reactivity control; coolant materials; shielding materials; nuclear fuel elements; nuclear material recovery from irradiated fuel and recycling; quality control of nuclear materials; materials for fusion reactors (thermonuclear fusion reaction, physical processes in fusion reactors, fuel materials, materials for blanket and cooling system, structural materials, materials for magnetic devices, specific problems of material irradiation). (U.K.)

The regulations concerning refining business of nuclear source material and nuclear fuel materials

International Nuclear Information System (INIS)

1987-01-01

Regulations specified here cover application for designation of undertakings of refining (spallation and eaching filtration facilities, thickening facilities, refining facilities, nuclear material substances or nuclear fuel substances storage facilities, waste disposal facilities, etc.), application for permission for alteration (business management plan, procurement plan, fund raising plan, etc.), application for approval of merger (procedure, conditions, reason and date of merger, etc.), submission of report on alteration (location, structure, arrangements processes and construction plan for refining facilities, etc.), revocation of designation, rules for records, rules for safety (personnel, organization, safety training for employees, handling of important apparatus and tools, monitoring and removal of comtaminants, management of radioactivity measuring devices, inspection and testing, acceptance, transport and storage of nuclear material and fuel, etc.), measures for emergency, submission of report on abolition of an undertaking, submission of report on disorganization, measures required in the wake of revocation of designation, submission of information report (exposure to radioactive rays, stolen or missing nuclear material or nuclear fuel, unusual leak of nuclear fuel or material contaminated with nuclear fuel), etc. (Nogami, K.)

Detection of materials of interest to nonproliferation: A novel approach

International Nuclear Information System (INIS)

Ze, Frederic; Tittmann, Bernhard R.; Lenahan, P.M.

2002-01-01

We propose the development of a novel detector that can locate and identify materials of interest to Nuclear Arms Non Proliferation. The device will combine nuclear acoustic resonance (NAR) with superconducting quantum interference device (SQUID) widely used in nuclear magnetic resonance (NMR), geophysics, nondestructive evaluations, and biomagnetism, to name only few. NAR works like NMR. Thus resonant absorption (of applied ultrasonic energy) by a nuclear spin system occurs when the ultrasonic frequency is equal to the appropriate frequency separations between the magnetic nuclear energy levels. Ultrasonic energy couples to the nuclear spin system via spin-phonon interaction. The resulting nuclear acoustic resonance can be detected via the changes in (a) ultrasonic attenuation, (b) ultrasonic velocity, (c) material magnetization, (d) or nuclear magnetic susceptibility, all of which carries 'intrinsic and unique signatures' of the material under investigation. The device's sensitivity and penetration depth (into metals) will be enhanced by incorporating SQUID technology into the design. We will present the details of interaction physics and outline a plan of action needed to successfully transform the concepts into a practical detector

Dealing with the regional challenge of physical protection of nuclear materials

International Nuclear Information System (INIS)

Paschoa, A.S.

2002-01-01

Full text: The problem of protecting sensitive fissile and fissionable nuclear materials of misuses by governments has been the subject of the convention on physical protection of nuclear material (CPPNM), which entered into force on February 8, 1987. However, in May 2001 the final report of the expert meeting had already recognized 'a clear need to strengthen the international physical protection regime'. The board of governors of the International Atomic Energy Agency (IAEA) decided then to convene a group, which would meet in Vienna from 3 to 7 December 2001, to draft on amendment to the CPPNM. The tragic occurrences of September 11, 2001, however, changed the then generally accepted view on the problem of physical protection, because nuclear materials had to be protected from falling into the hands of terrorists rather than of governments thirst of nuclear sensitive materials. Moreover, crude explosive devices could be made by terrorists, or hired scientists, using readily available radioactive materials, like 226 Ra or 137 Cs to inflict damage to civilians. Thus physical protection of those and other radioactive materials became an instant challenge for national and international authorities to prevent the use of such materials in terrorist actions. The prevention of illicit trafficking of radioactive materials is now in the priority list of these authorities. Fortunately; an international conference on 'Measures to Detect, Intercept and Respond to the Illicit Uses of Nuclear Materials and Radioactive Sources' was held in Stockholm, Sweden, in May 2001. An IAEA document - GOV/2001/37-GC(45)/20 - recommended in its plan of activities a series of projects to be implemented between 2002 and 2005, which included developing and providing assistance for the application of: (i) standards for physical protection of nuclear materials and nuclear facilities in member states; (ii) norms and guidelines for nuclear material accounting and control in member states; (iii

Global nuclear material control model

International Nuclear Information System (INIS)

Dreicer, J.S.; Rutherford, D.A.

1996-01-01

The nuclear danger can be reduced by a system for global management, protection, control, and accounting as part of a disposition program for special nuclear materials. The development of an international fissile material management and control regime requires conceptual research supported by an analytical and modeling tool that treats the nuclear fuel cycle as a complete system. Such a tool must represent the fundamental data, information, and capabilities of the fuel cycle including an assessment of the global distribution of military and civilian fissile material inventories, a representation of the proliferation pertinent physical processes, and a framework supportive of national or international perspective. They have developed a prototype global nuclear material management and control systems analysis capability, the Global Nuclear Material Control (GNMC) model. The GNMC model establishes the framework for evaluating the global production, disposition, and safeguards and security requirements for fissile nuclear material

Absolute nuclear material assay

Science.gov (United States)

Prasad, Manoj K [Pleasanton, CA; Snyderman, Neal J [Berkeley, CA; Rowland, Mark S [Alamo, CA

2010-07-13

A method of absolute nuclear material assay of an unknown source comprising counting neutrons from the unknown source and providing an absolute nuclear material assay utilizing a model to optimally compare to the measured count distributions. In one embodiment, the step of providing an absolute nuclear material assay comprises utilizing a random sampling of analytically computed fission chain distributions to generate a continuous time-evolving sequence of event-counts by spreading the fission chain distribution in time.

Physics and technology of nuclear materials

CERN Document Server

Ursu, Ioan

2015-01-01

Physics and Technology of Nuclear Materials presents basic information regarding the structure, properties, processing methods, and response to irradiation of the key materials that fission and fusion nuclear reactors have to rely upon. Organized into 12 chapters, this book begins with selectively several fundamentals of nuclear physics. Subsequent chapters focus on the nuclear materials science; nuclear fuel; structural materials; moderator materials employed to """"slow down"""" fission neutrons; and neutron highly absorbent materials that serve in reactor's power control. Other chapters exp

Technical considerations for detection of and response to illicit trafficking in radioactive materials

International Nuclear Information System (INIS)

Duftschmid, K.E.; Arlt, R.; Cunningham, J.; Gayral, J.P.; Kravchenko, N.; Smith, D.; York, R.

2001-01-01

Full text: The need for guidance and recommendations explicitly directed to the problem of illicit trafficking in nuclear materials and other radioactive sources was raised by the IAEA Director General at the IAEA General Conference in December 1994, and measures were agreed by the IAEA Board of Governors in March 1995. Measures that might be taken to prevent, detect, and respond to illicit trafficking will be common for all radioactive materials, including nuclear materials. However, nuclear materials are, or should be, subject also to safeguards for nuclear non-proliferation purposes and to physical protection to prevent diversion. The IAEA has established close co-operation with intergovernmental and non-governmental organizations, in particular the World Customs Organization (WCO) and INTERPOL to conduct joint studies, meetings and training programs to support Member States in their border control activities. Within this programme technical information has been derived on requirements and methods to detect and respond to events involving inadvertent movement of and illicit trafficking in radioactive materials. The paper summarises the most important results and the experience obtained in this field. Concerning 'detection' information on strategy of detection, selection of an investigation level, techniques for radiation monitoring at borders, verification of alarms, search techniques and identification of radionuclides has been developed. This includes recommended minimum requirements for monitoring equipment, derived from the results of an extended international pilot study on border monitoring equipment ITRAP, conducted by IAEA in co-operation with the Austrian government. In order to discover illicit trafficking or inadvertent movement in radioactive materials, the following steps are required: detection of any abnormal radiation level, verification of such detection, localisation of the origin of the radiation, radiation safety measurement, and

Test and evaluation of computerized nuclear material accounting methods. Final report

International Nuclear Information System (INIS)

1995-01-01

In accordance with the definition of a Material Balance Area (MBA) as a well-defined geographical area involving an Integral operation, the building housing the BFS-1 and BFS-1 critical facilities is considered to consist of one MBA. The BFS materials are in the form of small disks clad in stainless steel and each disk with nuclear material has its own serial number. Fissile material disks in the BFS MBA can be located at three key monitoring points: BFS-1 facility, BFS-2 facility and main storage of BFS fissile materials (storage 1). When used in the BFS-1 or BFS-2 critical facilities, the fissile material disks are loaded in tubes (fuel rods) forming critical assembly cores. The following specific features of the BFS MBA should be taken into account for the purpose of computerized accounting of nuclear material: (1) very large number of nuclear material items (about 70,000 fissile material items); and (2) periodically very intensive shuffling of nuclear material items. Requirements for the computerized system are determined by basic objectives of nuclear material accounting: (1) providing accurate information on the identity and location of all items in the BFS material balance area; (2) providing accurate information on location and identity of tamper-indicating devices; (3) tracking nuclear material inventories; (4) issuing periodic reports; (5) assisting with the detection of material gains or losses; (6) providing a history of nuclear material transactions; (7) preventing unauthorized access to the system and data falsification. In August 1995, the prototype computerized accounting system was installed on the BFS facility for trial operation. Information on two nuclear material types was entered into the data base: weapon-grade plutonium metal and 36% enriched uranium dioxide. The total number of the weapon-grade plutonium disks is 12,690 and the total number of the uranium dioxide disks is 1,700

The Department of Homeland Security’s Approach to Countering Nuclear Terrorism through Detection and Technical Forensics

Directory of Open Access Journals (Sweden)

Huban A. Gowadia

2015-07-01

Full Text Available To combat the threat of nuclear terrorism, the Domestic Nuclear Detection Office (DNDO was established within the U.S. Department of Homeland Security to focus efforts on developing and enhancing radiological and nuclear detection and national technical nuclear forensics capabilities. With respect to nuclear detection, we at DNDO, in concert with interagency partners, are developing and enhancing a multi-faceted, layered, defense-in-depth framework to make prohibitively difficult the importation, possession, storage, development, transportation, or use of nuclear or other radioactive material that is out of regulatory control. In furtherance of this framework, we conduct research and development on detection and forensics technologies, characterize system performance, acquire and deploy detection systems, and support operational partners with the development of programs to effectively perform detection operations. To support the U.S. Government’s (USG attribution process, we focus on improving the readiness of the overarching USG forensic capabilities; advancing the technical capabilities to perform forensic analyses on pre-detonation nuclear and other radioactive materials; and building and sustaining an expertise pipeline for nuclear forensic scientists. These efforts, coupled with the work of interagency partners, will advance USG capabilities to detect and interdict a nuclear threat and hold accountable those who are responsible for such actions.

Determination of internationally controlled materials according to provisions of the law for the regulations of nuclear source materials, nuclear fuel materials and reactors

International Nuclear Information System (INIS)

1984-01-01

The internationally controlled materials determined according to the law for nuclear source materials, etc. are the following: nuclear source materials, nuclear fuel materials, moderating materials, facilities including reactors, etc. sold, transferred, etc. to Japan according to the agreements for peaceful uses of atomic energy between Japan, and the United States, the United Kingdom, Canada, Australia and France by the respective governments and those organs under them; nuclear fuel materials resulting from usage of the above sold and transferred materials, facilities; nuclear fuel materials sold to Japan according to agreements set by the International Atomic Energy Agency; nuclear fuel materials involved with the safeguards in nuclear weapons non-proliferation treaty with IAEA. (Mori, K.)

Physical protection of nuclear materials and facilities in CEA

International Nuclear Information System (INIS)

Garnier-Gratia, M.-H.; Jorda, A.

2001-01-01

'. Guidelines have been written for both files. In the holding unit 'license and control file' guideline, activities, nuclear materials, locations and organization of the facility have to be described. About physical protection arrangements, guidelines are fitted to the category of nuclear materials. The following arrangements have to be presented: - for category I, reinforced protected area, building and vault delay arrangements, detection, access control, response force organization, control and maintenance of physical protection equipment, - for category II, protected area delay arrangements, detection, intervention, control and maintenance, - for category III, controlled area, access procedure. Whatever the category, nature and physical shape of nuclear material, containment and surveillance of the containment must be described. For the site, the operator has to present the operations performed on nuclear materials, the common means, its quality organization. For physical protection, site fence, gates, and surveillance principles have to be described. The operating procedures must also be presented: access of people and goods, nuclear materials transportation and patrols. The response force organization has to be explained: central alarm station, interruption procedures, training exercises and interaction with outside agencies. The paper will present these guidelines especially the physical protection chapters and will explain how CEA shows with this document that the regulatory requirements are fulfilled. (author)

Professional Nuclear Materials Management

International Nuclear Information System (INIS)

Forcella, A.A.; O'Leary, W.J.

1966-01-01

This paper describes the scope of nuclear materials management for a typical power reactor in the United States of America. Since this power reactor is financed by private capital, one of the principal obligations of the reactor operator is to ensure that the investment is protected and will furnish an adequate financial return. Because of the high intrinsic value of nuclear materials, appropriate security and accountability must be continually exercised to minimize losses beyond security and accountability for the nuclear materials. Intelligent forethought and planning must be employed to ensure that additional capital is not lost as avoidable additional costs or loss of revenue in a number of areas. The nuclear materials manager must therefore provide in advance against the following contingencies and maintain constant control or liaison against deviations from planning during (a) pre-reactor acquisition of fuel and fuel elements, (b) in-reactor utilization of the fuel elements, and (c) post-reactor recovery of fuel values. During pre-reactor planning and operations, it is important that the fuel element be designed for economy in manufacture, handling, shipping, and replaceability. The time schedule for manufacturing operations must minimize losses of revenue from unproductive dead storage of high cost materials. For in-reactor operations, the maximum achievable burn-up of the fissionable material must be obtained by means of appropriate fuel rearrangement schemes. Concurrently the unproductive down-time of the reactor for fuel rearrangement, inspections, and the like must be minimized. In the post-reactor period, when the fuel has reached a predetermined depletion of fissionable material, the nuclear materials manager must provide for the most economical reprocessing and recovery of fissionable values and by-products. Nuclear materials management is consequently an essential factor in achieving competitive fuel cycle and unit energy costs with power reactors

Remote Detection and Location of Illegal Radioactive Materials Units in Uzbekistan

International Nuclear Information System (INIS)

Khaydarov, R. A.; Khaydarov, R. R.

2007-01-01

Uzbekistan is a checkpoint for transportation between Russia and some Asian countries, such as Iran, Pakistan, Afghanistan and Tajikistan that might be attractive destinations for those smuggling nuclear materials or weapons. Currently there are over 200 border crossing points. Most of them have equipped with monitors able to reliably detect nuclear materials. Uzbekistan also has substantial radioactive ore mining, and these monitors also allow the Customs Service to maintain safe conditions for their inspectors as well as for population of Uzbekistan and its neighbors. But it is very important to detect radioactive materials inland, their location and travel. This task cannot be solved by using stationary detectors which are used at border crossing points. New method, electronic scheme and software for remote detection, location and travel of radioactive sources were developed. The operation principle lies in detection of radiation by 6 detectors situated in a leaden cylindrical shield collimating gamma-radiation in 6 directions. Besides the detection system contains 6 amplifiers, 6 counters and JPS-system connected with computer. The detection system is transported by car. Field tests of the detection system have shown that the detection limit is 5. 106 Bq and 4.106 Bq for Co60 and Cs137 respectively when the radioactive sources distance is 400 m. (author)

Control of unauthorized transportation of nuclear and radioactive materials across state territories and borders: detection, response and decision support

International Nuclear Information System (INIS)

Stavrov, Andrei; Frymire, Allan; Kagan, Leonid; Karczewski, Jerzy

2008-01-01

A new solution to control the illicit transportation of nuclear and radioactive materials is proposed and described. This solution consists in the creation of a system of gamma and gamma-neutron radiation monitors and fundamentally new software/hardware package RAVEN (Radiation Alarm and Video Event Notification) which integrates different type monitors in a single network. The main purpose of this system is to analyze and store data coming from radiation monitors, to process these data and to help the user to interpret them. This ensures the user's correct response to all the alarms triggered by radiation monitors and indicating the presence of radioactive and/or nuclear materials in scanned objects. The developed system can integrate fixed radiation monitors that can be installed in different sites within not only one country but in different sites worldwide in a single network. The system can be adapted to the local conditions and allows the user: (i) To detect minimum quantities of special nuclear and radioactive materials (specified by the national and international requirements) by their gamma and/or neutron radiation; (ii) To acquire, store and analyze digital data and video images related to cargos with radioactive materials crossing a state border or an object limits; (iii) To make these data accessible to users at different levels ensuring effective operation of both central alarm stations (state, regional or agency center) and local alarm stations (border cross points or object limits). (author)

Definition of Nuclear Material in Aspects of Nuclear Nonproliferation and Security

International Nuclear Information System (INIS)

Jeon, Ji Hye; Lee, Chan Suh

2014-01-01

Nuclear safety accidents directly affect human health but nuclear security incidents indirectly influence human, which demonstrates the reason why security receives less attention. However, it is acknowledged that nuclear terrorism is indeed one of the most dreadful threat humanity faces. As part of strengthening nuclear security as well as nonproliferation to response to the threat, we need a better understanding of the nuclear material which needs to be safe under the objective of nuclear security. In reality, practitioners implement safeguards and physical protection in compliance with the regulation text in domestic legislation. Thus, it is important to specify nuclear material clearly in law for effective implementation. Therefore, the definition of terminology related to nuclear material is explored herein, within the highest-level legislation on the safeguards and physical protection. First the definition in Korean legislation is analyzed. Then, so as to suggest some improvements, other international efforts are examined and some case studies are conducted on other states which have similar level of nuclear technology and industry to Korea. Finally, a draft of definition on nuclear material in perspective of nuclear nonproliferation and security is suggested based on the analysis below. The recommendation showed the draft nuclear material definition in nuclear control. The text will facilitate the understanding of nuclear material in the context of nuclear nonproliferation and security. It might provide appropriate provision for future legislation related to nuclear nonproliferation and security. For effective safeguards and physical protection measures, nuclear material should be presented with in a consistent manner as shown in the case of United Kingdom. It will be much more helpful if further material engineering studies on each nuclear material are produced. Multi-dimensional approach is required for the studies on the degree of efforts to divert

Definition of Nuclear Material in Aspects of Nuclear Nonproliferation and Security

Energy Technology Data Exchange (ETDEWEB)

Jeon, Ji Hye; Lee, Chan Suh [Korea Institute of Nuclear Nonproliferation and Control, Daejeon (Korea, Republic of)

2014-10-15

Nuclear safety accidents directly affect human health but nuclear security incidents indirectly influence human, which demonstrates the reason why security receives less attention. However, it is acknowledged that nuclear terrorism is indeed one of the most dreadful threat humanity faces. As part of strengthening nuclear security as well as nonproliferation to response to the threat, we need a better understanding of the nuclear material which needs to be safe under the objective of nuclear security. In reality, practitioners implement safeguards and physical protection in compliance with the regulation text in domestic legislation. Thus, it is important to specify nuclear material clearly in law for effective implementation. Therefore, the definition of terminology related to nuclear material is explored herein, within the highest-level legislation on the safeguards and physical protection. First the definition in Korean legislation is analyzed. Then, so as to suggest some improvements, other international efforts are examined and some case studies are conducted on other states which have similar level of nuclear technology and industry to Korea. Finally, a draft of definition on nuclear material in perspective of nuclear nonproliferation and security is suggested based on the analysis below. The recommendation showed the draft nuclear material definition in nuclear control. The text will facilitate the understanding of nuclear material in the context of nuclear nonproliferation and security. It might provide appropriate provision for future legislation related to nuclear nonproliferation and security. For effective safeguards and physical protection measures, nuclear material should be presented with in a consistent manner as shown in the case of United Kingdom. It will be much more helpful if further material engineering studies on each nuclear material are produced. Multi-dimensional approach is required for the studies on the degree of efforts to divert

Nuclear materials management storage study

International Nuclear Information System (INIS)

Becker, G.W. Jr.

1994-02-01

The Office of Weapons and Materials Planning (DP-27) requested the Planning Support Group (PSG) at the Savannah River Site to help coordinate a Departmental complex-wide nuclear materials storage study. This study will support the development of management strategies and plans until Defense Programs' Complex 21 is operational by DOE organizations that have direct interest/concerns about or responsibilities for nuclear material storage. They include the Materials Planning Division (DP-273) of DP-27, the Office of the Deputy Assistant Secretary for Facilities (DP-60), the Office of Weapons Complex Reconfiguration (DP-40), and other program areas, including Environmental Restoration and Waste Management (EM). To facilitate data collection, a questionnaire was developed and issued to nuclear materials custodian sites soliciting information on nuclear materials characteristics, storage plans, issues, etc. Sites were asked to functionally group materials identified in DOE Order 5660.1A (Management of Nuclear Materials) based on common physical and chemical characteristics and common material management strategies and to relate these groupings to Nuclear Materials Management Safeguards and Security (NMMSS) records. A database was constructed using 843 storage records from 70 responding sites. The database and an initial report summarizing storage issues were issued to participating Field Offices and DP-27 for comment. This report presents the background for the Storage Study and an initial, unclassified summary of storage issues and concerns identified by the sites

Nuclear material operations manual

International Nuclear Information System (INIS)

Tyler, R.P.

1981-02-01

This manual provides a concise and comprehensive documentation of the operating procedures currently practiced at Sandia National Laboratories with regard to the management, control, and accountability of nuclear materials. The manual is divided into chapters which are devoted to the separate functions performed in nuclear material operations-management, control, accountability, and safeguards, and the final two chapters comprise a document which is also issued separately to provide a summary of the information and operating procedures relevant to custodians and users of radioactive and nuclear materials. The manual also contains samples of the forms utilized in carrying out nuclear material activities. To enhance the clarity of presentation, operating procedures are presented in the form of playscripts in which the responsible organizations and necessary actions are clearly delineated in a chronological fashion from the initiation of a transaction to its completion

Nuclear material operations manuals

International Nuclear Information System (INIS)

Tyler, R.P.

1979-06-01

This manual is intended to provide a concise and comprehensive documentation of the operating procedures currently practiced at Sandia Laboratories with regard to the management, control, and accountability of radioactive and nuclear materials. The manual is divided into chapters which are devoted to the separate functions performed in nuclear material operations-management, control, accountability, and safeguards, and the final two chapters comprise a document which is also issued separately to provide a summary of the information and operating procedures relevant to custodians and users of radioactive and nuclear materials. The manual also contains samples of the forms utilized in carrying out nuclear material activities. To enhance the clarity of presentation, operating procedures are presented in the form of playscripts in which the responsible organizations and necessary actions are clearly delineated in a chronological fashion from the initiation of a transaction to its completion

Selection of nuclear reactor coolant materials

International Nuclear Information System (INIS)

Shi Lisheng; Wang Bairong

2012-01-01

Nuclear material is nuclear material or materials used in nuclear industry, the general term, it is the material basis for the construction of nuclear power, but also a leader in nuclear energy development, the two interdependent and mutually reinforcing. At the same time, nuclear materials research, development and application of the depth and breadth of science and technology reflects a nation and the level of the nuclear power industry. Coolant also known as heat-carrier agent, is an important part of the heart nuclear reactor, its role is to secure as much as possible to the economic output in the form fission energy to heat the reactor to be used: the same time cooling the core, is controlled by the various structural components allowable temperature. This paper described the definition of nuclear reactor coolant and characteristics, and then addressed the requirements of the coolant material, and finally were introduced several useful properties of the coolant and chemical control. (authors)

Time-series-analysis techniques applied to nuclear-material accounting

International Nuclear Information System (INIS)

Pike, D.H.; Morrison, G.W.; Downing, D.J.

1982-05-01

This document is designed to introduce the reader to the applications of Time Series Analysis techniques to Nuclear Material Accountability data. Time series analysis techniques are designed to extract information from a collection of random variables ordered by time by seeking to identify any trends, patterns, or other structure in the series. Since nuclear material accountability data is a time series, one can extract more information using time series analysis techniques than by using other statistical techniques. Specifically, the objective of this document is to examine the applicability of time series analysis techniques to enhance loss detection of special nuclear materials. An introductory section examines the current industry approach which utilizes inventory differences. The error structure of inventory differences is presented. Time series analysis techniques discussed include the Shewhart Control Chart, the Cumulative Summation of Inventory Differences Statistics (CUSUM) and the Kalman Filter and Linear Smoother

Radiation, ionization, and detection in nuclear medicine

International Nuclear Information System (INIS)

Gupta, Tapan K.

2013-01-01

Up-to-date information on a wide range of topics relating to radiation, ionization, and detection in nuclear medicine. In-depth coverage of basic radiophysics relating to diagnosis and therapy. Extensive discussion of instrumentation and radiation detectors. Detailed information on mathematical modelling of radiation detectors. Although our understanding of cancer has improved, the disease continues to be a leading cause of death across the world. The good news is that the recent technological developments in radiotherapy, radionuclide diagnostics and therapy, digital imaging systems, and detection technology have raised hope that cancer will in the future be combatted more efficiently and effectively. For this goal to be achieved, however, safe use of radionuclides and detailed knowledge of radiation sources are essential. Radiation, Ionization, and Detection in Nuclear Medicine addresses these subjects and related issues very clearly and elaborately and will serve as the definitive source of detailed information in the field. Individual chapters cover fundamental aspects of nuclear radiation, including dose and energy, sources, and shielding; the detection and measurement of radiation exposure, with detailed information on mathematical modelling; medical imaging; the different types of radiation detector and their working principles; basic principles of and experimental techniques for deposition of scintillating materials; device fabrication; the optical and electrical behaviors of radiation detectors; and the instrumentation used in nuclear medicine and its application. The book will be an invaluable source of information for academia, industry, practitioners, and researchers.

Radiation, ionization, and detection in nuclear medicine

Energy Technology Data Exchange (ETDEWEB)

Gupta, Tapan K. [Radiation Monitoring Devices Research, Nuclear Medicine, Watertown, MA (United States)

2013-08-01

Up-to-date information on a wide range of topics relating to radiation, ionization, and detection in nuclear medicine. In-depth coverage of basic radiophysics relating to diagnosis and therapy. Extensive discussion of instrumentation and radiation detectors. Detailed information on mathematical modelling of radiation detectors. Although our understanding of cancer has improved, the disease continues to be a leading cause of death across the world. The good news is that the recent technological developments in radiotherapy, radionuclide diagnostics and therapy, digital imaging systems, and detection technology have raised hope that cancer will in the future be combatted more efficiently and effectively. For this goal to be achieved, however, safe use of radionuclides and detailed knowledge of radiation sources are essential. Radiation, Ionization, and Detection in Nuclear Medicine addresses these subjects and related issues very clearly and elaborately and will serve as the definitive source of detailed information in the field. Individual chapters cover fundamental aspects of nuclear radiation, including dose and energy, sources, and shielding; the detection and measurement of radiation exposure, with detailed information on mathematical modelling; medical imaging; the different types of radiation detector and their working principles; basic principles of and experimental techniques for deposition of scintillating materials; device fabrication; the optical and electrical behaviors of radiation detectors; and the instrumentation used in nuclear medicine and its application. The book will be an invaluable source of information for academia, industry, practitioners, and researchers.

Nuclear material accounting handbook

International Nuclear Information System (INIS)

2008-01-01

The handbook documents existing best practices and methods used to account for nuclear material and to prepare the required nuclear material accounting reports for submission to the IAEA. It provides a description of the processes and steps necessary for the establishment, implementation and maintenance of nuclear material accounting and control at the material balance area, facility and State levels, and defines the relevant terms. This handbook serves the needs of State personnel at various levels, including State authorities, facility operators and participants in training programmes. It can assist in developing and maintaining accounting systems which will support a State's ability to account for its nuclear material such that the IAEA can verify State declarations, and at the same time support the State's ability to ensure its nuclear security. In addition, the handbook is useful for IAEA staff, who is closely involved with nuclear material accounting. The handbook includes the steps and procedures a State needs to set up and maintain to provide assurance that it can account for its nuclear material and submit the prescribed nuclear material accounting reports defined in Section 1 and described in Sections 3 and 4 in terms of the relevant agreement(s), thereby enabling the IAEA to discharge its verification function as defined in Section 1 and described in Sections 3 and 4. The contents of the handbook are based on the model safeguards agreement and, where applicable, there will also be reference to the model additional protocol. As a State using The handbook consists of five sections. In Section 1, definitions or descriptions of terms used are provided in relation to where the IAEA applies safeguards or, for that matter, accounting for and control of nuclear material in a State. The IAEA's approach in applying safeguards in a State is also defined and briefly described, with special emphasis on verification. In Section 2, the obligations of the State

The law for the regulations of nuclear source materials, nuclear fuel materials and reactors

International Nuclear Information System (INIS)

1977-01-01

Concerning refining, fabrication and reprocessing operations of such materials as well as the installation and operation of reactors, necessary regulations are carried out. Namely, in case of establishing the business of refining, fabricating and reprocessing nuclear materials as well as installing nuclear reactors, applications for the permission of the Prime Minister and the Minister of International Trade and Industry should be filed. Change of such operations should be permitted after filing applications. These permissions are retractable. As regards the reactors installed aboard foreign ships, it must be reported to enter Japanese waters and the permission by the Prime Minister must be obtained. In case of nuclear fuel fabricators, a chief technician of nuclear fuel materials (qualified) must be appointed per each fabricator. In case of installing nuclear reactors, the design and methods of construction should be permitted by the Prime Minister. The standard for such permission is specified, and a chief engineer for operating reactors (qualified) must be appointed. Successors inherit the positions of ones who have operated nuclear material refining, fabrication and reprocessing businesses or operated nuclear reactors. (Rikitake, Y.)

Nuclear material management: challenges and prospects

International Nuclear Information System (INIS)

Rieu, J.; Besnainou, J.; Leboucher, I.; Chiguer, M.; Capus, G.; Greneche, D.; Durret, L.F.; Carbonnier, J.L.; Delpech, M.; Loaec, Ch.; Devezeaux de Lavergne, J.G.; Granger, S.; Devid, S.; Bidaud, A.; Jalouneix, J.; Toubon, H.; Pochon, E.; Bariteau, J.P.; Bernard, P.; Krellmann, J.; Sicard, B.

2008-01-01

The articles in this dossier were derived from the papers of the yearly S.F.E.N. convention, which took place in Paris, 12-13 March 2008. They deal with the new challenges and prospects in the field of nuclear material management, throughout the nuclear whole fuel cycle, namely: the institutional frame of nuclear materials management, the recycling, the uranium market, the enrichment market, the different scenarios for the management of civil nuclear materials, the technical possibilities of spent fuels utilization, the option of thorium, the convention on the physical protection of nuclear materials and installations, the characterisation of nuclear materials by nondestructive nuclear measurements, the proliferation from civil installations, the use of plutonium ( from military origin) and the international agreements. (N.C.)

Nuclear material operations manual

International Nuclear Information System (INIS)

Tyler, R.P.; Gassman, L.D.

1978-04-01

This manual is intended to provide a concise and comprehensive documentation of the operating procedures currently practiced at Sandia Laboratories with regard to the management, control, and accountability of radioactive and nuclear materials. The manual is divided into chapters which are devoted to the separate functions performed in nuclear material operations--management, control, accountability, and safeguards, and the final two chapters comprise a document which is also issued separately to provide a summary of the information and operating procedures relevant to custodians and users of radioactive and nuclear materials. The manual also contains samples of the forms utilized in carrying out nuclear material activities. To enhance the clarity of presentation, operating procedures are presented in the form of ''play-scripts'' in which the responsible organizations and necessary actions are clearly delineated in a chronological fashion from the initiation of a transaction to its completion

Nuclear measurements and reference materials

International Nuclear Information System (INIS)

1988-01-01

This report summarizes the progress of the JRC programs on nuclear data, nuclear metrology, nuclear reference materials and non-nuclear reference materials. Budget restrictions and personnel difficulties were encountered during 1987. Fission properties of 235 U as a function of neutron energy and of the resonances can be successfully described on the basis of a three exit channel fission model. Double differential neutron emission cross-sections were accomplished on 7 Li and were started for the tritium production cross-section of 9 Be. Reference materials of uranium minerals and ores were prepared. Special nuclear targets were prepared. A batch of 250 g of Pu0 2 was characterized in view of certification as reference material for the elemental assay of plutonium

Safeguards for nuclear material transparency monitoring

International Nuclear Information System (INIS)

MacArthur, D.A.; Wolford, J.K.

1999-01-01

The US and the Russian Federation are currently engaged in negotiating or implementing several nuclear arms and nuclear material control agreements. These involve placing nuclear material in specially designed containers within controlled facilities. Some of the agreements require the removal of nuclear components from stockpile weapons. These components are placed in steel containers that are then sealed and tagged. Current strategies for monitoring the agreements involve taking neutron and gamma radiation measurements of components in their containers to monitor the presence, mass, and composition of plutonium or highly enriched uranium, as well as other attributes that indicate the use of the material in a weapon. If accurate enough to be useful, these measurements will yield data containing information about the design of the weapon being monitored. In each case, the design data are considered sensitive by one or both parties to the agreement. To prevent the disclosure of this information in a bilateral or trilateral inspection scenario, so-called information barriers have evolved. These barriers combine hardware, software, and procedural safeguards to contain the sensitive data within a protected volume, presenting to the inspector only the processed results needed for verification. Interlocks and volatile memory guard against disclosure in case of failure. Implementing these safeguards requires innovation in radiation measurement instruments and data security. Demonstrating their reliability requires independent testing to uncover any flaws in design. This study discusses the general problem and gives a proposed solution for a high resolution gamma ray detection system. It uses historical examples to illustrate the evolution of other successful systems

Nuclear materials management procedures

International Nuclear Information System (INIS)

Veevers, K.; Silver, J.M.; Quealy, K.J.; Steege, E. van der.

1987-10-01

This manual describes the procedures for the management of nuclear materials and associated materials at the Lucas Heights Research Laboratories. The procedures are designed to comply with Australia's nuclear non-proliferation obligations to the International Atomic Energy Agency (IAEA), bilateral agreements with other countries and ANSTO's responsibilities under the Nuclear Non-Proliferation (Safeguards) Act, 1987. The manual replaces those issued by the Australian Atomic Energy Commission in 1959, 1960 and 1969

Material input of nuclear fuel

International Nuclear Information System (INIS)

Rissanen, S.; Tarjanne, R.

2001-01-01

The Material Input (MI) of nuclear fuel, expressed in terms of the total amount of natural material needed for manufacturing a product, is examined. The suitability of the MI method for assessing the environmental impacts of fuels is also discussed. Material input is expressed as a Material Input Coefficient (MIC), equalling to the total mass of natural material divided by the mass of the completed product. The material input coefficient is, however, only an intermediate result, which should not be used as such for the comparison of different fuels, because the energy contents of nuclear fuel is about 100 000-fold compared to the energy contents of fossil fuels. As a final result, the material input is expressed in proportion to the amount of generated electricity, which is called MIPS (Material Input Per Service unit). Material input is a simplified and commensurable indicator for the use of natural material, but because it does not take into account the harmfulness of materials or the way how the residual material is processed, it does not alone express the amount of environmental impacts. The examination of the mere amount does not differentiate between for example coal, natural gas or waste rock containing usually just sand. Natural gas is, however, substantially more harmful for the ecosystem than sand. Therefore, other methods should also be used to consider the environmental load of a product. The material input coefficient of nuclear fuel is calculated using data from different types of mines. The calculations are made among other things by using the data of an open pit mine (Key Lake, Canada), an underground mine (McArthur River, Canada) and a by-product mine (Olympic Dam, Australia). Furthermore, the coefficient is calculated for nuclear fuel corresponding to the nuclear fuel supply of Teollisuuden Voima (TVO) company in 2001. Because there is some uncertainty in the initial data, the inaccuracy of the final results can be even 20-50 per cent. The value

Experience in safeguarding nuclear material at the Rheinsberg nuclear power station

International Nuclear Information System (INIS)

Winkler, R.

1976-01-01

The three years' experience that has been gained in application of the Safeguards Agreement shows that the carrying out of inspections at the nuclear power plant has virtually no effect on operating conditions. In future it will be possible to reduce this effect even further and still maintain the operational reliability of the station. Verification of the transfer of nuclear material and detection of possible violations have proved relatively simple. The labour requirement of each unit at the station for the performance of inspections is not more that thirty man-days. Constructive collaboration between power station staff and inspectors is of great importance in improving the safeguards procedures. (author)

Statistical methods for nuclear material management

International Nuclear Information System (INIS)

Bowen, W.M.; Bennett, C.A.

1988-12-01

This book is intended as a reference manual of statistical methodology for nuclear material management practitioners. It describes statistical methods currently or potentially important in nuclear material management, explains the choice of methods for specific applications, and provides examples of practical applications to nuclear material management problems. Together with the accompanying training manual, which contains fully worked out problems keyed to each chapter, this book can also be used as a textbook for courses in statistical methods for nuclear material management. It should provide increased understanding and guidance to help improve the application of statistical methods to nuclear material management problems

Statistical methods for nuclear material management

Energy Technology Data Exchange (ETDEWEB)

Bowen W.M.; Bennett, C.A. (eds.)

1988-12-01

This book is intended as a reference manual of statistical methodology for nuclear material management practitioners. It describes statistical methods currently or potentially important in nuclear material management, explains the choice of methods for specific applications, and provides examples of practical applications to nuclear material management problems. Together with the accompanying training manual, which contains fully worked out problems keyed to each chapter, this book can also be used as a textbook for courses in statistical methods for nuclear material management. It should provide increased understanding and guidance to help improve the application of statistical methods to nuclear material management problems.

Considerations for sampling nuclear materials for SNM accounting measurements. Special nuclear material accountability report

International Nuclear Information System (INIS)

Brouns, R.J.; Roberts, F.P.; Upson, U.L.

1978-05-01

This report presents principles and guidelines for sampling nuclear materials to measure chemical and isotopic content of the material. Development of sampling plans and procedures that maintain the random and systematic errors of sampling within acceptable limits for SNM(Special Nuclear Materials) accounting purposes are emphasized

Nuclear Materials Management. Proceedings of the Symposium on Nuclear Materials Management

Energy Technology Data Exchange (ETDEWEB)

NONE

1966-02-15

An increasing number of countries are using nuclear materials which, because of their high value and the potential hazards involved, require special methods of handling. To discuss these and to provide a forum at which different systems for achieving the necessary economy and safety could be compared, the International Atomic Energy Agency held a Symposium at Vienna on Nuclear Materials Management from 30 August to 3 September, 1965. It was attended by 115 participants from 19 Member States and two international organizations. Nuclear materials are already being used on an industrial scale and their high cost demands close and continuous control to ensure that they are delivered precisely on time and that they are used to the fullest possible extent before they are withdrawn from service. Routine industrial methods of material control and verification are widely used to ensure safe and economical operation and handling in nuclear power stations, in fuel-element fabrication and reprocessing plants, and in storage facilities. In addition special refinements are needed to take account of the value and the degree of purity required of nuclear materials. Quality as well as quantity has to be checked thoroughly and the utmost economy in processing is necessary. The radioactivity of the material poses special problems of handling and storage and creates a potential hazard to health. A further problem is that of criticality. These dangers and the means of averting them are well understood, as is evidenced by the outstandingly good safety record of the atomic energy industry. But besides accommodating all these special problems, day-to-day procedures must be simple enough to fit in with industrial conditions. Many of the 58 papers presented at the Symposium emphasized that records, checks, measurements and handling precautions, if suitably devised, provide the control vital to efficient operation, serve as checks against loss or waste of valuable materials and help meet the

Determination of internationally controlled materials according to provisions of the law for the regulations of nuclear source materials, nuclear fuel materials and reactors

International Nuclear Information System (INIS)

1981-01-01

This rule is established under the provisions of the law concerning the regulation of nuclear raw materials, nuclear fuel materials and reactors, and the former notification No. 26, 1961, is hereby abolished. Internationally regulated goods under the law are as follows: nuclear raw materials, nuclear fuel materials and moderator materials transferred by sale or other means from the governments of the U.S., U.K., Canada, Australia and France or the persons under their jurisdictions according to the agreements concluded between the governments of Japan and these countries, respectively, the nuclear fuel materials recovered from these materials or produced by their usage, nuclear reactors, the facilities and heavy water transferred by sale or other means from these governments or the persons under their jurisdictions, the nuclear fuel materials produced by the usage of such reactors, facilities and heavy water, the nuclear fuel materials sold by the International Atomic Energy Agency under the contract between the Japanese government and the IAEA, the nuclear fuel materials recovered from these materials or produced by their usage, the heavy water produced by the facilities themselves transferred from the Canadian government, Canadian governmental enterprises or the persons under the jurisdiction of the Canadian government or produced by the usage of these facilities, etc. (Okada, K.)

Advanced research workshop: nuclear materials safety

International Nuclear Information System (INIS)

Jardine, L J; Moshkov, M M.

1999-01-01

The Advanced Research Workshop (ARW) on Nuclear Materials Safety held June 8-10, 1998, in St. Petersburg, Russia, was attended by 27 Russian experts from 14 different Russian organizations, seven European experts from six different organizations, and 14 U.S. experts from seven different organizations. The ARW was conducted at the State Education Center (SEC), a former Minatom nuclear training center in St. Petersburg. Thirty-three technical presentations were made using simultaneous translations. These presentations are reprinted in this volume as a formal ARW Proceedings in the NATO Science Series. The representative technical papers contained here cover nuclear material safety topics on the storage and disposition of excess plutonium and high enriched uranium (HEU) fissile materials, including vitrification, mixed oxide (MOX) fuel fabrication, plutonium ceramics, reprocessing, geologic disposal, transportation, and Russian regulatory processes. This ARW completed discussions by experts of the nuclear materials safety topics that were not covered in the previous, companion ARW on Nuclear Materials Safety held in Amarillo, Texas, in March 1997. These two workshops, when viewed together as a set, have addressed most nuclear material aspects of the storage and disposition operations required for excess HEU and plutonium. As a result, specific experts in nuclear materials safety have been identified, know each other from their participation in t he two ARW interactions, and have developed a partial consensus and dialogue on the most urgent nuclear materials safety topics to be addressed in a formal bilateral program on t he subject. A strong basis now exists for maintaining and developing a continuing dialogue between Russian, European, and U.S. experts in nuclear materials safety that will improve the safety of future nuclear materials operations in all the countries involved because of t he positive synergistic effects of focusing these diverse backgrounds of

Decree No. 208 On National Accounting and Control System of the Nuclear Materials

International Nuclear Information System (INIS)

1996-01-01

The present Decree establishes the arrangements to formalize the National Accounting and Control System of the Nuclear Materials, the which one has the objectives of contributing to an efficient and economic management of the nuclear materials in the national territory; to establish the arrangements directed to detect any employment, lost or unauthorized movement of the nuclear material; and to establish the measures of necessary control to give fulfillment to the international commitments assumed by the Cuban State in relationship to the nuclear materials, important components, or both. It also establishes the following responsibilities: The Ministry of Science Technology and Environment is the Organism of the Central Administration of the State responsible for the supervision and control of the dispositions and it delegates in the National Center of Nuclear Security the execution of the functions assigned to this Ministry

Nuclear and mitochondrial DNA quantification of various forensic materials.

Science.gov (United States)

Andréasson, H; Nilsson, M; Budowle, B; Lundberg, H; Allen, M

2006-12-01

Due to the different types and quality of forensic evidence materials, their DNA content can vary substantially, and particularly low quantities can impact the results in an identification analysis. In this study, the quantity of mitochondrial and nuclear DNA was determined in a variety of materials using a previously described real-time PCR method. DNA quantification in the roots and distal sections of plucked and shed head hairs revealed large variations in DNA content particularly between the root and the shaft of plucked hairs. Also large intra- and inter-individual variations were found among hairs. In addition, DNA content was estimated in samples collected from fingerprints and accessories. The quantification of DNA on various items also displayed large variations, with some materials containing large amounts of nuclear DNA while no detectable nuclear DNA and only limited amounts of mitochondrial DNA were seen in others. Using this sensitive real-time PCR quantification assay, a better understanding was obtained regarding DNA content and variation in commonly analysed forensic evidence materials and this may guide the forensic scientist as to the best molecular biology approach for analysing various forensic evidence materials.

Evaluating the attractiveness of nuclear material for proliferation-resistance and nuclear security

International Nuclear Information System (INIS)

Choi, Jor-Shan; Ikegame, Kou; Kuno, Yusuke

2011-01-01

The attractiveness of nuclear material, defined as a function of the isotopic composition of the nuclear material in formulas expressing the material's intrinsic properties, is of considerably debate in recent developments of proliferation-resistance measures of a nuclear energy system. A reason for such debate arises from the fact that the concept of nuclear material attractiveness can be confusing because the desirability of a material for nuclear explosive use depends on many tangible and intangible factors including the intent and capability of the adversary. In addition, a material that is unattractive to an advanced nation (in the case of proliferation) may be very attractive to a terrorist (in the case of physical protection and nuclear security). Hence, the concept of 'Nuclear Material Attractiveness' for different nuclear materials must be considered in the context of safeguards and security. The development of a ranking scheme on the attractiveness of nuclear materials could be a useful concept to start-off the strategies for safeguards and security on a new footing (i.e., why and how nuclear material is attractive, and what are the quantifiable basis). Japan may benefit from such concept regarding the attractiveness of nuclear materials when recovering nuclear materials from the damaged cores in Fukushima because safety, security, and safeguards (3S) would be a prominent consideration for the recovery operation, and it would be the first time such operation is performed in a non-nuclear weapons state. (author)

Uncertainty estimation in nuclear material weighing

Energy Technology Data Exchange (ETDEWEB)

Thaure, Bernard [Institut de Radioprotection et de Surete Nucleaire, Fontenay aux Roses, (France)

2011-12-15

The assessment of nuclear material quantities located in nuclear plants requires knowledge of additions and subtractions of amounts of different types of materials. Most generally, the quantity of nuclear material held is deduced from 3 parameters: a mass (or a volume of product); a concentration of nuclear material in the product considered; and an isotopic composition. Global uncertainties associated with nuclear material quantities depend upon the confidence level of results obtained in the measurement of every different parameter. Uncertainties are generally estimated by considering five influencing parameters (ISHIKAWA's rule): the material itself; the measurement system; the applied method; the environmental conditions; and the operator. A good practice guide, to be used to deal with weighing errors and problems encountered, is presented in the paper.

Radiological and Nuclear Detection Material Science: Novel Rare-Earth Semiconductors for Solid-State Neutron Detectors and Thin High-k Dielectrics

Science.gov (United States)

2017-11-01

6201 Fort Belvoir, VA 22060-6201 T E C H N IC A L R E P O R T DTRA-TR-15-82 Radiological and Nuclear Detection Material Science : Novel...P.A. Dowben, “Surface Charging at the (100) Surface of Cu doped and undoped Li2B4O7”, Applied Surface Science 257 (2011) 3399-3403 27. S.R...V.T. Adamiv, Ya.V. Burak, P.A. Dowben, “The local structure of Mn doped Li2B4O7(001)”, in preparation for Materials Science and Engineering B 40. C

Measures against illicit trafficking of nuclear and other radioactive materials in the Slovak Republic

International Nuclear Information System (INIS)

Bezak, S.

2001-01-01

Full text: This presentation contains description of measures used in the Slovak Republic to combat illicit trafficking of nuclear and other radioactive materials. The main goal of these measures is to allow safe and effective utilization of nuclear and other radioactive materials under surveillance of responsible state authorities as well as recover materials that were removed form legal utilization despite the preventive measures. Prevention is the most effective and the cheapest way how to overcome problems. An important precondition for prevention is existence of a national (or state) system for controlled utilization of nuclear and other radioactive materials completed by an effective physical protection of these materials and facilities involved and supported by sufficient low enforcement. A state system of accounting for and control of nuclear materials in Slovakia is based on the IAEA INFCIRC/153 requirements. A fact that the IAEA inspectors never have recognized any unaccounted nuclear material could be the best proof of its quality. Physical protection system in both Slovak NPPs is based on principles applied in development of advanced physical protection systems used in western NPPs. Technological systems and nuclear materials are categorized into three categories - first one is most sensitive. Barriers of each category zone are equipped with sufficient detection systems and are monitored by TV system. The system is operated by NPPs operators. Entrances are guarded by private security guards. Response forces are created by the police. A legal support provides the Act No. 130/1998 on peaceful use of nuclear energy and regulations on accounting and control of nuclear materials, on physical protection of nuclear facilities and nuclear materials and on transports of nuclear materials and radioactive wastes. The Criminal Code of the Slovak Republic has been amended and an illegal possession of nuclear and radioactive materials is treated as a crime. Response

Photonuclear-based Detection of Nuclear Smuggling in Cargo Containers

Science.gov (United States)

Jones, J. L.; Haskell, K. J.; Hoggan, J. M.; Norman, D. R.; Yoon, W. Y.

2003-08-01

The Idaho National Engineering and Environmental Laboratory (INEEL) and the Los Alamos National Laboratory (LANL) have performed experiments in La Honda, California and at the Idaho Accelerator Center in Pocatello, Idaho to assess and develop a photonuclear-based detection system for shielded nuclear materials in cargo containers. The detection system, measuring photonuclear-related neutron emissions, is planned for integration with the ARACOR Eagle Cargo Container Inspection System (Sunnyvale, CA). The Eagle Inspection system uses a nominal 6-MeV electron accelerator and operates with safe radiation exposure limits to both container stowaways and to its operators. The INEEL has fabricated custom-built, helium-3-based, neutron detectors for this inspection application and is performing an experimental application assessment. Because the Eagle Inspection system could not be moved to LANL where special nuclear material was available, the response of the Eagle had to be determined indirectly so as to support the development and testing of the detection system. Experiments in California have successfully matched the delayed neutron emission performance of the ARACOR Eagle with that of the transportable INEEL electron accelerator (i.e., the Varitron) and are reported here. A demonstration test is planned at LANL using the Varitron and shielded special nuclear materials within a cargo container. Detector results are providing very useful information regarding the challenges of delayed neutron counting near the photofission threshold energy of 5.5 - 6.0 MeV, are identifying the possible utilization of prompt neutron emissions to allow enhanced signal-to-noise measurements, and are showing the overall benefits of using higher electron beam energies.

The Physical Protection of Nuclear Material and Nuclear Facilities

International Nuclear Information System (INIS)

1999-08-01

Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international co-operation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and nuclear materials, particularly when such materials are transported across national frontiers

The Physical Protection of Nuclear Material and Nuclear Facilities

International Nuclear Information System (INIS)

1999-06-01

Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international co-operation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and nuclear materials, particularly when such materials are transported across national frontiers [es

The Physical Protection of Nuclear Material and Nuclear Facilities

International Nuclear Information System (INIS)

1999-06-01

Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international co-operation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and nuclear materials, particularly when such materials are transported across national frontiers

Smuggling special nuclear materials

International Nuclear Information System (INIS)

Lazaroiu, Gheorghe

1999-01-01

Ever since the collapse of the former Soviet Union reports have circulated with increasing frequency concerning attempts to smuggle materials from that country's civil and military nuclear programs. Such an increase obviously raises a number of concerns (outlined in the author's introduction), chief among which is the possibility that these materials might eventually fall into the hands of proliferant states or terrorist groups. The following issues are presented: significance of materials being smuggled; sources and smuggling routes; potential customers; international efforts to reduce nuclear smuggling; long-term disposition of fissile materials. (author)

Special nuclear material inventory sampling plans

International Nuclear Information System (INIS)

Vaccaro, H.; Goldman, A.

1987-01-01

Since their introduction in 1942, sampling inspection procedures have been common quality assurance practice. The U.S. Department of Energy (DOE) supports such sampling of special nuclear materials inventories. The DOE Order 5630.7 states, Operations Offices may develop and use statistically valid sampling plans appropriate for their site-specific needs. The benefits for nuclear facilities operations include reduced worker exposure and reduced work load. Improved procedures have been developed for obtaining statistically valid sampling plans that maximize these benefits. The double sampling concept is described and the resulting sample sizes for double sample plans are compared with other plans. An algorithm is given for finding optimal double sampling plans that assist in choosing the appropriate detection and false alarm probabilities for various sampling plans

An intelligence led approach to intercepting the illicit trafficking of nuclear and other radioactive material

International Nuclear Information System (INIS)

Kulinich, O.

2001-01-01

Recognizing the actuality and importance of nuclear material illicit trafficking problems, the Security Service of Ukraine pays great attention to the security and theft prevention of nuclear materials in Ukraine. For this purpose the state system, which includes organizational and legislative measures, has been established and is functioning. Within the frame of this system the detection and perception of illicit trafficking of nuclear materials and radioactive substances take an important place in the work of law enforcement authorities, including Security Service, in Ukraine. The Laws of Ukraine nuclear power utilization and radioactive safety, sanitary and epidemiological population control, the respective articles of the Criminal Code of Ukraine (art. 228-2, 228-3, 228-4, 228-5) and the statement of the Cabinet of Ministers of Ukraine no. 207 on 04.03.1997 which determines the interaction procedure between executive authorities in case of illicit trafficking of radiation source detection, are its legislative basis. The analysis of the situation shows that this problem became the most pressing after the USSR collapse in 1991 due to some objective and subjective causes. Some criminals and common staff of the enterprises and organizations which were responsible for the above mentioned materials as well as former military men were involved in illegal activity associated with illicit trafficking of nuclear materials and radioactive substances. Although after the USSR collapsed the Ukraine had the nuclear arsenal which was the third in the world, it did not become the source of nuclear weapons material proliferation. It shows the effectiveness of the measures undertaken by the government within the system of nuclear material physical protection provision. It is evident that nuclear weapon removal from the territory of Ukraine was performed without any case of its loss or theft. Therefore, currently in Ukraine there is only the necessary amount of nuclear material

Nuclear battery materials and application of nuclear batteries

International Nuclear Information System (INIS)

Hao Shaochang; Lu Zhenming; Fu Xiaoming; Liang Tongxiang

2006-01-01

Nuclear battery has lots of advantages such as small volume, longevity, environal stability and so on, therefore, it was widely used in aerospace, deep-sea, polar region, heart pacemaker, micro-electromotor and other fields etc. The application of nuclear battery and the development of its materials promote each other. In this paper the development and the latest research progress of nuclear battery materials has been introduced from the view of radioisotope, electric energy conversion and encapsulation. And the current and potential applications of the nuclear battery are also summarized. (authors)

Nuclear materials stewardship: Our enduring mission

International Nuclear Information System (INIS)

Isaacs, T.H.

1998-01-01

The US Department of Energy (DOE) and its predecessors have handled a remarkably wide variety of nuclear materials over the past 50 yr. Two fundamental changes have occurred that shape the current landscape regarding nuclear materials. If one recognizes the implications and opportunities, one sees that the stewardship of nuclear materials will be a fundamental and important job of the DOE for the foreseeable future. The first change--the breakup of the Soviet Union and the resulting end to the nuclear arms race--altered US objectives. Previously, the focus was on materials production, weapon design, nuclear testing, and stockpile enhancements. Now the attention is on dismantlement of weapons, excess special nuclear material inventories, accompanying increased concern over the protection afforded to such materials; new arms control measures; and importantly, maintenance of the safety and reliability of the remaining arsenal without testing. The second change was the raised consciousness and sense of responsibility for dealing with the environmental legacies of past nuclear arms programs. Recognition of the need to clean up radioactive contamination, manage the wastes, conduct current operations responsibly, and restore the environment have led to the establishment of what is now the largest program in the DOE. Two additional features add to the challenge and drive the need for recognition of nuclear materials stewardship as a fundamental, enduring, and compelling mission of the DOE. The first is the extraordinary time frames. No matter what the future of nuclear weapons and no matter what the future of nuclear power, the DOE will be responsible for most of the country's nuclear materials and wastes for generations. Even if the Yucca Mountain program is successful and on schedule, it will last more than 100 yr. Second, the use, management, and disposition of nuclear materials and wastes affect a variety of nationally important and diverse objectives, from national

Nuclear Security Recommendations on Nuclear and other Radioactive Material out of Regulatory Control: Recommendations (Spanish Edition); Recomendaciones de Seguridad Fisica Nuclear sobre Materiales Nucleares y otros Materiales Radiactivos no sometidos a Control Reglamentario: Recomendaciones

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-06-15

This publication presents recommendations for the nuclear security of nuclear and other radioactive material that is out of regulatory control. It is based on national experiences and practices and guidance publications in the field of security as well as the nuclear security related international instruments. The recommendations include guidance for States with regard to the nuclear security of nuclear and other radioactive material that has been reported as being out of regulatory control as well as for material that is lost, missing or stolen but has not been reported as such, or has been otherwise discovered. In addition, these recommendations adhere to the detection and assessment of alarms and alerts and to a graded response to criminal or unauthorized acts with nuclear security implications.

Development of measures to deal with illicit trafficking of nuclear materials in Ghana

International Nuclear Information System (INIS)

Schandorf, C.; Amoako, J.K.; Asiamah, S.D.

2001-01-01

the environment. Ghana seeks to build upon the established regulatory control programme for the control of ionizing radiation and radiation sources and to expand it to cover combating of illicit trafficking of nuclear materials of socio-economic importance. The prevention of strategy will involve developing a national system for the accountability, control and security of nuclear materials. Technical measures to detect Illicit trafficking of nuclear materials and other radioactive materials and response to illicit trafficking will be developed. The programme will include screening of vehicles and individuals at borders to: (i) detect smuggling of these materials; (ii) locate, measure and characterize the source of radiation; and (iii) fully characterize any confiscated materials. An effective countermeasure will be established through a system of (i) Prevention: Establishment of national system of accounting and control of nuclear materials; Legislation and regulations; Physical Protection; Export/Import control; (ii) Response to illicit trafficking through: Establishing anti-trafficking infrastructure, which includes responsible authorities such as customs, civil aviation authority, police, nuclear regulatory authority, military intelligence and defense agencies, and district assemblies coordinating and collaborating in combating illicit trafficking: (iii) Provision of detecting equipment for nuclear materials and (iv) Training which will cater to: response personnel and the public. Training opportunities provided by the IAEA will be fully utilized. International collaboration with our near neighbors, Togo, Cote d'lvoire and Burkina Faso, will be established to ensure cross border control. (author)

Determination of internationally controlled materials according to provisions of the law for the regulations of nuclear source materials, nuclear fuel materials and reactors

International Nuclear Information System (INIS)

1977-01-01

According to the provisions of The Law, those stipulated as internationally controlled materials are nuclear source materials, nuclear fuel materials, moderating materials, reactors and facilities, transferred from such as the U.S.A., the U.K. and Canada on the agreements of peaceful uses of atomic energy, and nuclear fuel materials accruing therefrom. (Mori, K.)

The nuclear reaction analysis (NRA) as a means for detecting carbon in GaAs and in source materials and additives

International Nuclear Information System (INIS)

Bethge, K.; Mader, A.; Michelmann, R.; Krauskopf, J.; Thee, P.; Meyer, J.D.

1991-01-01

The nuclear reaction ananlysis (NRA) on the basis of the reaction 12 C (d,p) 13 C is a method allowing the detection and description of both lateral and depth profiles of the presence of carbon in GaAs and in the source materials and additives. The NRA is an absolute method with a detection limit for C of approx. 4x10 15 cm 3 . The achievable detection range in depth under the experimental conditions goes from the surface down to 6 μm. Combined with channeling measurements, NRA is capable of identifying the position of carbon in the GaAs crystal lattice, and thus permits to examine the mobility of C in GaAs. (BBR) With 11 refs [de

Thermodynamics of nuclear materials

International Nuclear Information System (INIS)

Rand, M.H.

1975-01-01

A report is presented of the Fourth International Symposium on Thermodynamics of Nuclear Materials held in Vienna, 21-25 October 1974. The technological theme of the Symposium was the application of thermodynamics to the understanding of the chemistry of irradiated nuclear fuels and to safety assessments for hypothetical accident conditions in reactors. The first four sessions were devoted to these topics and they were followed by four more sessions on the more basic thermodynamics, phase diagrams and the thermodynamic properties of a wide range of nuclear materials. Sixty-seven papers were presented

Global nuclear material flow/control model

International Nuclear Information System (INIS)

Dreicer, J.S.; Rutherford, D.S.; Fasel, P.K.; Riese, J.M.

1997-01-01

This is the final report of a two-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The nuclear danger can be reduced by a system for global management, protection, control, and accounting as part of an international regime for nuclear materials. The development of an international fissile material management and control regime requires conceptual research supported by an analytical and modeling tool which treats the nuclear fuel cycle as a complete system. The prototype model developed visually represents the fundamental data, information, and capabilities related to the nuclear fuel cycle in a framework supportive of national or an international perspective. This includes an assessment of the global distribution of military and civilian fissile material inventories, a representation of the proliferation pertinent physical processes, facility specific geographic identification, and the capability to estimate resource requirements for the management and control of nuclear material. The model establishes the foundation for evaluating the global production, disposition, and safeguards and security requirements for fissile nuclear material and supports the development of other pertinent algorithmic capabilities necessary to undertake further global nuclear material related studies

Techniques and methods in nuclear materials traceability

International Nuclear Information System (INIS)

Persiani, P.J.

1996-01-01

The nonproliferation community is currently addressing concerns that the access to special nuclear materials may increase the illicit trafficking in weapons-usable materials from civil and/or weapons material stores and/or fuel cycles systems. Illicit nuclear traffic usually involves reduced quantities of nuclear materials perhaps as samplings of a potential protracted diversionary flow from sources to users. To counter illicit nuclear transactions requires the development of techniques and methods in nuclear material traceability as an important phase of a broad forensic analysis capability. This report discusses how isotopic signatures and correlation methods were applied to determine the origins of Highly Enriched Uranium (HEU) and Plutonium samples reported as illicit trafficking in nuclear materials

Application of crime countermeasures for the protection of nuclear materials

International Nuclear Information System (INIS)

Bean, C.H.

1975-01-01

Federal regulations prepared by the Nuclear Regulatory Commission and published in the Federal Register require licensees to take appropriate action to protect the health and safety of the public from unauthorized use of special nuclear material (SNM), which includes plutonium, uranium-233, and highly enriched uranium. Crime countermeasures for compliance with these regulations are an important part of the guidance that is provided by the NRC's Office of Standards Development. The use of crime countermeasures and protective devices is intended to prevent the unauthorized diversion of material and to aid in the detection of diversion should it be attempted. Plant and equipment designs should incorporate both electronic and physical security measures for protection of SNM. This applies to facilities and equipment for reprocessing, fabrication, and transportation of SNM. The protection systems include physical barriers, access controls, intrusion detection devices, surveillance devices, central alarm stations, communications, and response capability. Acceptable security measures and devices applicable to protected areas, material access areas, vital areas, vital equipment, and transportation vehicles have been presented in Regulatory Guides. (U.S.)

The system of nuclear material control of Kazakhstan

International Nuclear Information System (INIS)

Yeligbayeva, G.Zh.

2001-01-01

Full text: The State system for nuclear material control consists of three integral components. The efficiency of each is to guarantee the non-proliferation regime in Kazakhstan. The components are the following: accounting, export and import control and physical protection of nuclear materials. First, the implementation of the goals of accounting and control bring into force, by the organization of the system for accounting and measurement of nuclear materials to determine present quantity. Organizing the accounting for nuclear material at facilities will ensure the efficiency of accountancy and reporting information. This defines the effectiveness of the state system for the accounting for the Kazakhstan's nuclear materials. Currently, Kazakhstan's nuclear material is fully safeguarded in designated secure locations. Kazakhstan has a nuclear power plant, 4 research reactors and a fuel fabrication plant. The governmental information system for nuclear materials control consist of two level: Governmental level - KAEA collects reports from facilities and prepares the reports for International Atomic Energy Agency, keeping of supporting documents and other necessary information, a data base of export and import, a data base of nuclear material inventory. Facility level - registration and processing information from key measurement points, formation the facility's nuclear materials accounting database. All facilities have computerized systems. Currently, all facilities are safeguarded under IAEA safeguarding standards, through IAEA inspections. Annually, IAEA verifies all nuclear materials at all Kazakhstan nuclear facilities. The government reporting system discloses the existence of all nuclear material and its transfer intended for interaction through the export control system and the nuclear control accounting system. Nuclear material export is regulated by the regulations of the Nuclear Export Control Law. The standard operating procedure is the primary means for

Control of nuclear material specified equipment and specified material

International Nuclear Information System (INIS)

1982-04-01

The goal and application field of NE 2.02 regulatory guide of CNEN (Comissao Nacional de Energia Nuclear), are described. This regulatory guide is about nuclear material management, specified equipment and specified material. (E.G.) [pt

Physical protection of nuclear material

International Nuclear Information System (INIS)

1975-01-01

Full text: An Advisory Group met to consider the up-dating and extension of the Recommendations for the Physical Protection of Nuclear Material, produced in 1972. Twenty-seven experts from 11 countries and EURATOM were present. Growing concern has been expressed in many countries that nuclear material may one day be used for acts of sabotage or terrorism. Serious attention is therefore being given to the need for States to develop national systems for the physical protection of nuclear materials during use, storage and transport throughout the nuclear fuel cycle which should minimize risks of sabotage or theft. The revised Recommendations formulated by the Advisory Group include new definitions of the objectives of national systems of physical protection and proposals for minimizing possibilities of unauthorized removal and sabotage to nuclear facilities. The Recommendations also describe administrative or organizational steps to be taken for this purpose and the essential technical requirements of physical protection for various types and locations of nuclear material, e.g., the setting up of protected areas, the use of physical barriers and alarms, the need for security survey, and the need of advance arrangements between the States concerned in case of international transportation, among others. (author)

Nuclear science in the 20th century. Nuclear technology applications in material science

International Nuclear Information System (INIS)

Pei Junchen; Xu Furong; Zheng Chunkai

2003-01-01

The application of nuclear technology to material science has led to a new cross subject, nuclear material science (also named nuclear solid physics) which covers material analysis, material modification and new material synthesis. This paper reviews the development of nuclear technical applications in material science and the basic physics involved

Expanding Nuclear Power Programmes - Romanian experience: Master - Nuclear Materials and Technologies Educational Plan

International Nuclear Information System (INIS)

Valeca, S.; Valeca, M.

2012-01-01

The main objectives of the Master Nuclear Materials and Technologies Educational Plan are: 1. To deliver higher education and training in the following specific domains, such as: Powders Technology and Ceramic Materials, Techniques of Structural Analysis, Composite Materials, Semiconductor Materials and Components, Metals and Metallic Alloys, Optoelectronic Materials and Devices, Nuclear Materials, The Engineering of Special Nuclear Materials, 2. To train managers of the Nuclear Waste Products and Nuclear Safety, 3. To qualify in ICT Systems for Nuclear Process Guidance, 4. To qualify in Environmental Protection System at the Level of Nuclear Power Stations, 5. To train managers for Quality Assurance of Nuclear Energetic Processes, 6. To deliver higher education and training regarding the International Treatises, Conventions and Settlements in force in the field of nuclear related activities. (author)

United States Department of Energy Nuclear Materials Stewardship

International Nuclear Information System (INIS)

Newton, J. W.

2002-01-01

The Department of Energy launched the Nuclear Materials Stewardship Initiative in January 2000 to accelerate the work of achieving integration and cutting long-term costs associated with the management of the Department's nuclear materials, with the principal focus on excess materials. Management of nuclear materials is a fundamental and enduring responsibility that is essential to meeting the Department's national security, nonproliferation, energy, science, and environmental missions into the distant future. The effective management of nuclear materials is important for a set of reasons: (1) some materials are vital to our national defense; (2) the materials pose physical and security risks; (3) managing them is costly; and (4) costs are likely to extend well into the future. The Department currently manages nuclear materials under eight programs, with offices in 36 different locations. Through the Nuclear Materials Stewardship Initiative, progress was during calendar year 20 00 in achieving better coordination and integration of nuclear materials management responsibilities and in evaluating opportunities to further coordinate and integrate cross-program responsibilities for the treatment, storage, and disposition of excess nuclear materials. During CY 2001 the Departmental approach to nuclear materials stewardship changed consistent with the business processes followed by the new administration. This paper reports on the progress of the Nuclear Materials Stewardship Initiative in evaluating and implementing these opportunities, and the remaining challenges in integrating the long-term management of nuclear materials

The law for the regulations of nuclear source materials, nuclear fuel materials and reactors

International Nuclear Information System (INIS)

1980-01-01

The law intends under the principles of the atomic energy act to regulate the refining, processing and reprocessing businesses of nuclear raw and fuel metarials and the installation and operation of reactors for the peaceful and systematic utilization of such materials and reactors and for securing public safety by preventing disasters, as well as to control internationally regulated things for effecting the international agreements on the research, development and utilization of atomic energy. Basic terms are defined, such as atomic energy; nuclear fuel material; nuclear raw material; nuclear reactor; refining; processing; reprocessing; internationally regulated thing. Any person who is going to engage in refining businesses other than the Power Reactor and Nuclear Fuel Development Corporation shall get the special designation by the Prime Minister and the Minister of International Trade Industry. Any person who is going to engage in processing businesses shall get the particular admission of the Prime Minister. Any person who is going to establish reactors shall get the particular admission of the Prime Minister, The Minister of International Trade and Industry or the Minister of Transportation according to the kinds of specified reactors, respectively. Any person who is going to engage in reprocessing businesses other than the Power Reactor and Nuclear Fuel Development Corporation and the Japan Atomic Energy Research Institute shall get the special designation by the Prime Minister. The employment of nuclear fuel materials and internationally regulated things is defined in detail. (Okada, K.)

The physical protection of nuclear material

International Nuclear Information System (INIS)

1989-12-01

A Technical Committee on Physical Protection of Nuclear Material met in April-May 1989 to advise on the need to update the recommendations contained in document INFCIRC/225/Rev.1 and on any changes considered to be necessary. The Technical Committee indicated a number of such changes, reflecting mainly: the international consensus established in respect of the Convention on the Physical Protection of Nuclear Material; the experience gained since 1977; and a wish to give equal treatment to protection against the theft of nuclear material and protection against the sabotage of nuclear facilities. The recommendations presented in this IAEA document reflect a broad consensus among Member States on the requirements which should be met by systems for the physical protection of nuclear materials and facilities. 1 tab

Approaches to characterization of nuclear material for establishment of nuclear forensics

International Nuclear Information System (INIS)

Okazaki, Hiro; Sumi, Mika; Sato, Mitsuhiro; Kayano, Masashi; Kageyama, Tomio; Shinohara, Nobuo; Martinez, Patrick; Xu, Ning; Thomas, Mariam; Porterfield, Donivan; Colletti, Lisa; Schwartz, Dan; Tandon, Lav

2014-01-01

The Plutonium Fuel Development Center (PFDC) of Japan Atomic Energy Agency has been analyzing isotopic compositions and contents of plutonium and uranium as well as trace impurities and physics in the nuclear fuel from MOX fuel fabrication process for accountancy and process control purpose. These analytical techniques are also effective for nuclear forensics to identify such as source, history, and route of the material by determining a composition and characterization of nuclear material. Therefore, PFDC cooperates with Los Alamos National Laboratory which has broad experience and established measurement skill for nuclear forensics, and evaluates the each method, procedure and analytical data toward R and D of characterizing a nuclear material for forensic purposes. This paper describes the approaches to develop characterization techniques of nuclear material for nuclear forensics purposes at PFDC. (author)

Fuzzy controllers in nuclear material accounting

International Nuclear Information System (INIS)

Zardecki, A.

1994-01-01

Fuzzy controllers are applied to predicting and modeling a time series, with particular emphasis on anomaly detection in nuclear material inventory differences. As compared to neural networks, the fuzzy controllers can operate in real time; their learning process does not require many iterations to converge. For this reason fuzzy controllers are potentially useful in time series forecasting, where the authors want to detect and identify trends in real time. They describe an object-oriented implementation of the algorithm advanced by Wang and Mendel. Numerical results are presented both for inventory data and time series corresponding to chaotic situations, such as encountered in the context of strange attractors. In the latter case, the effects of noise on the predictive power of the fuzzy controller are explored

Supplier responsibility for nuclear material quality

International Nuclear Information System (INIS)

Stuart, P.S.; Dohna, A.E.

1976-01-01

Nuclear materials must be delivered by either the manufacturer or the distributor with objective, documented evidence that the material was manufactured, inspected, and tested by proven techniques performed by qualified personnel working to documented procedures. Measurement devices used for acceptance must be of proven accuracy. The material and all records must be identified for positive traceability as part of the quality history of the nuclear components, system, or structure in which the material was used. In conclusion, the nuclear material supplier must join the fabricator, the installer, and the user in effective implementation of the total systems approach to the application of quality assurance principles to all phases of procurement, fabrication, installation, and use of the safety-related components, systems, and structures in a nuclear power plant

Advanced Neutron Detection Methods: new Tools for Countering Nuclear Terrorism (412th Brookhaven Lecture)

International Nuclear Information System (INIS)

Vanier, Peter

2006-01-01

Acts of terrorism have become almost daily occurrences in the international news. Yet one of the most feared types of terrorism - nuclear terrorism - has not yet happened. One important way of preventing nuclear terrorism is to safeguard nuclear materials, and many people worldwide work continuously to achieve that goal. A second, vital defense is being developed: greatly improved methods of detecting material that a nuclear terrorist would need so that timely discovery of the material could become more probable. Special nuclear materials can emit neutrons, either spontaneously or when excited by a source of high-energy gamma rays, such as an electron accelerator. Traditional neutron detectors can sense these neutrons, but not the direction from which the neutrons come, or their energy. The odds against finding smuggled nuclear materials using conventional detectors are great. However, innovative designs of detectors are producing images that show the locations and even the shapes of man-made neutron sources, which stand out against the uniform background produced by cosmic rays. With the new detectors, finding needles in haystacks - or smuggled nuclear materials in a huge container among thousands of others in a busy port - suddenly becomes possible.

Study on interface between nuclear material accounting system and national nuclear forensic library

International Nuclear Information System (INIS)

Jeong, Yonhong; Han, Jae-Jun; Chang, Sunyoung; Shim, Hye-Won; Ahn, Seungho

2016-01-01

The implementation of nuclear forensics requires physical, chemical and radiological characteristics with transport history to unravel properties of seized nuclear materials. For timely assessment provided in the ITWG guideline, development of national response system (e.g., national nuclear forensic library) is strongly recommended. Nuclear material accounting is essential to obtain basic data in the nuclear forensic implementation phase from the perspective of nuclear non-proliferation related to the IAEA Safeguards and nuclear security. In this study, the nuclear material accounting reports were chosen due to its well-established procedure, and reviewed how to efficiently utilize the existing material accounting system to the nuclear forensic implementation phase In conclusion, limits and improvements in implementing the nuclear forensics were discussed. This study reviewed how to utilize the existing material accounting system for implementing nuclear forensics. Concerning item counting facility, nuclear material properties can be obtained based on nuclear material accounting information. Nuclear fuel assembly data being reported for the IAEA Safeguards can be utilized as unique identifier within the back-end fuel cycle. Depending upon the compulsory accountability report period, there exist time gaps. If national capabilities ensure that history information within the front-end nuclear fuel cycle is traceable particularly for the bulk handling facility, the entire cycle of national nuclear fuel would be managed in the framework of developing a national nuclear forensic library

Study on interface between nuclear material accounting system and national nuclear forensic library

Energy Technology Data Exchange (ETDEWEB)

Jeong, Yonhong; Han, Jae-Jun; Chang, Sunyoung; Shim, Hye-Won; Ahn, Seungho [Korea Institute of Nuclear Non-proliferation and Control, Daejeon (Korea, Republic of)

2016-10-15

The implementation of nuclear forensics requires physical, chemical and radiological characteristics with transport history to unravel properties of seized nuclear materials. For timely assessment provided in the ITWG guideline, development of national response system (e.g., national nuclear forensic library) is strongly recommended. Nuclear material accounting is essential to obtain basic data in the nuclear forensic implementation phase from the perspective of nuclear non-proliferation related to the IAEA Safeguards and nuclear security. In this study, the nuclear material accounting reports were chosen due to its well-established procedure, and reviewed how to efficiently utilize the existing material accounting system to the nuclear forensic implementation phase In conclusion, limits and improvements in implementing the nuclear forensics were discussed. This study reviewed how to utilize the existing material accounting system for implementing nuclear forensics. Concerning item counting facility, nuclear material properties can be obtained based on nuclear material accounting information. Nuclear fuel assembly data being reported for the IAEA Safeguards can be utilized as unique identifier within the back-end fuel cycle. Depending upon the compulsory accountability report period, there exist time gaps. If national capabilities ensure that history information within the front-end nuclear fuel cycle is traceable particularly for the bulk handling facility, the entire cycle of national nuclear fuel would be managed in the framework of developing a national nuclear forensic library.

Study of nuclear material accounting

International Nuclear Information System (INIS)

Ruderman, H.

1977-01-01

The implications of deliberate diversion of nuclear materials on materials accounting, the validity of the MUF concept to establish assurance concerning the possible diversion of special nuclear materials, and an economic analysis to permit cost comparison of varying the inventory frequency are being studied. An inventory cost model, the statistical hypothesis testing approach, the game theoretic approach, and analysis of generic plants are considered

Combating illicit trafficking in nuclear and other radioactive material. Technical guidance. Reference manual. (Chinese Edition)

International Nuclear Information System (INIS)

2012-01-01

This publication is intended for individuals and organizations that may be called upon to deal with the detection of and response to criminal or unauthorized acts involving nuclear or other radioactive material. It will also be useful for legislators, law enforcement agencies, government officials, technical experts, lawyers, diplomats and users of nuclear technology. This manual emphasizes the international initiatives for improving the security of nuclear and other radioactive material. However, it is recognized that effective measures for controlling the transfer of equipment, non-nuclear material, technology or information that may assist in the development of nuclear explosive devices, improvised nuclear devices (INDs) or other radiological dispersal devices (RDDs) are important elements of an effective nuclear security system. In addition, issues of personal integrity, inspection and investigative procedures are not discussed in this manual, all of which are essential elements for an effective overall security system. The manual considers a variety of elements that are recognized as being essential for dealing with incidents of criminal or unauthorized acts involving nuclear and other radioactive material. Depending on conditions in a specific State, including its legal and governmental infrastructure, some of the measures discussed will need to be adapted to suit that State's circumstances. However, much of the material can be applied directly in the context of other national programmes. This manual is divided into four main parts. Section 2 discusses the threat posed by criminal or unauthorized acts involving nuclear and other radioactive material, as well as the policy and legal bases underlying the international effort to restrain such activities. Sections 3 and 4 summarize the major international undertakings in the field. Sections 5-8 provide some basic technical information on radiation, radioactive material, the health consequences of radiation

Nuclear fuel element leak detection system

International Nuclear Information System (INIS)

John, C.D. Jr.

1978-01-01

Disclosed is a leak detection system integral with a wall of a building used to fabricate nuclear fuel elements for detecting radiation leakage from the nuclear fuel elements as the fuel elements exit the building. The leak detecting system comprises a shielded compartment constructed to withstand environmental hazards extending into a similarly constructed building and having sealed doors on both ends along with leak detecting apparatus connected to the compartment. The leak detecting system provides a system for removing a nuclear fuel element from its fabrication building while testing for radiation leaks in the fuel element

Nuclear material control in Spain

International Nuclear Information System (INIS)

Velilla, A.

1988-01-01

A general view about the safeguards activities in Spain is presented. The national system of accounting for and control of nuclear materials is described. The safeguards agreements signed by Spain are presented and the facilities and nuclear materials under these agreements are listed. (E.G.) [pt

Automated nuclear materials accounting

International Nuclear Information System (INIS)

Pacak, P.; Moravec, J.

1982-01-01

An automated state system of accounting for nuclear materials data was established in Czechoslovakia in 1979. A file was compiled of 12 programs in the PL/1 language. The file is divided into four groups according to logical associations, namely programs for data input and checking, programs for handling the basic data file, programs for report outputs in the form of worksheets and magnetic tape records, and programs for book inventory listing, document inventory handling and materials balance listing. A similar automated system of nuclear fuel inventory for a light water reactor was introduced for internal purposes in the Institute of Nuclear Research (UJV). (H.S.)

Development of nuclear material accountancy control system

International Nuclear Information System (INIS)

Hirosawa, Naonori; Kashima, Sadamitsu; Akiba, Mitsunori

1992-01-01

PNC is developing a wide area of nuclear fuel cycle. Therefore, much nuclear material with a various form exists at each facility in the Works, and the controls of the inventory changes and the physical inventories of nuclear material are important. Nuclear material accountancy is a basic measure in safeguards system based on Non-Proliferation Treaty (NPT). In the light of such importance of material accountancy, the data base of nuclear material control and the material accountancy report system for all facilities has been developed by using the computer. By this system, accountancy report to STA is being presented certainly and timely. Property management and rapid corresponding to various inquiries can be carried out by the data base system which has free item searching procedure. (author)

New materials in nuclear fusion reactors

International Nuclear Information System (INIS)

Iwata, Shuichi

1988-01-01

In the autumn of 1987, the critical condition was attained in the JET in Europe and Japanese JT-60, thus the first subject in the physical verification of nuclear fusion reactors was resolved, and the challenge to the next attainment of self ignition condition started. As the development process of nuclear fusion reactors, there are the steps of engineering, economical and social verifications after this physical verification, and in respective steps, there are the critical problems related to materials, therefore the development of new materials must be advanced. The condition of using nuclear fusion reactors is characterized by high fluence, high thermal flux and strong magnetic field, and under such extreme condition, the microscopic structures of materials change, and they behave much differently from usual case. The subjects of material development for nuclear fusion reactors, the material data base being built up, the materials for facing plasma and high thermal flux, first walls, blanket structures, electric insulators and others are described. The serious effect of irradiation and the rate of defect inducement must be taken in consideration in the structural materials for nuclear fusion reactors. (Kako, I.)

Strengthening global practices for protecting nuclear material (NUMAT). Book of Abstracts

International Nuclear Information System (INIS)

Steinhaeusler, F.; Heissl, C.

2002-08-01

The International Conference on Physical Protection 'Strengthening Global Practices for Protecting Nuclear Material' was organized by the Institute of Physics and Biophysics, Salzburg University in cooperation with/supported by the European Commission, Lawrence Livermore National Laboratory, European Forum of the Stanford University's Institute for International Studies and Austria Institute for European Security. Its purpose was fostering exchange of information on the policy and technical aspects require to ensure the security of nuclear material around the world. There is a general concern that the international community needs to establish effective measures to counter theft, sabotage, and other illicit uses of nuclear fissile and other radioactive materials. The main subjects addressed by this conference were: a) global and local threat development and 'design basis'; b) standards for physical protection (PP), its adequacy and future needs; c) national practices in PP of nuclear materials (how to strengthen national security culture?); d) current R and D in security and detection technologies (identification of focus points for future R and D); e) programmes to aid in training, design, and implementation of physical protection systems (how to improve efficiency and assure sustainability of assistance programmes?). (nevyjel)

The physical protection of nuclear material and nuclear facilities

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-01

The latest review (1993) of this document was of limited scope and resulted in changes to the text of INFCIRC/225/Rev.2 designed to make the categorization table in that document consistent with the categorization table contained in the Convention on Physical Protection of Nuclear Materials. Consequently, a comprehensive review of INFCIRC/225 has not been conducted since 1989. Consequently, a meeting of national experts was convened from 2-5 June 1998 and from 27-29 October 1998 for a thorough review of INFCIRC/225/Rev.3. The revised document reflects the recommendations of the national experts to improve the structure and clarity of the document and to take account of improved technology and current international and national practices. In particular, a chapter has been added which provides specific recommendations related to sabotage of nuclear facilities and nuclear material. As a result of this addition, the title has been changed to 'The Physical Protection of Nuclear Material and Nuclear Facilities'. The recommendations presented in this IAEA document reflect a broad consensus among Member States on the requirements which should be met by systems for the physical protection of nuclear materials and facilities. It is hoped that they will provide helpful guidance for Member States.

The physical protection of nuclear material and nuclear facilities

International Nuclear Information System (INIS)

1999-06-01

The latest review (1993) of this document was of limited scope and resulted in changes to the text of INFCIRC/225/Rev.2 designed to make the categorization table in that document consistent with the categorization table contained in the Convention on Physical Protection of Nuclear Materials. Consequently, a comprehensive review of INFCIRC/225 has not been conducted since 1989. Consequently, a meeting of national experts was convened from 2-5 June 1998 and from 27-29 October 1998 for a thorough review of INFCIRC/225/Rev.3. The revised document reflects the recommendations of the national experts to improve the structure and clarity of the document and to take account of improved technology and current international and national practices. In particular, a chapter has been added which provides specific recommendations related to sabotage of nuclear facilities and nuclear material. As a result of this addition, the title has been changed to 'The Physical Protection of Nuclear Material and Nuclear Facilities'. The recommendations presented in this IAEA document reflect a broad consensus among Member States on the requirements which should be met by systems for the physical protection of nuclear materials and facilities. It is hoped that they will provide helpful guidance for Member States

Graphite materials for nuclear reactors

International Nuclear Information System (INIS)

Oku, Tatsuo

1991-01-01

Graphite materials have been used in the nuclear fission reactors from the beginning of the reactor development for the speed reduction and reflection of neutron. Graphite materials are used both as a moderator and as a reflector in the core of high temperature gas-cooled reactors, and both as a radiation shielding material and as a reflector in the surrounding of the core for the fast breeder reactor. On the other hand, graphite materials are being positively used as a first wall of plasma as it is known that low Z materials are useful for holding high temperature plasma in the nuclear fusion devices. In this paper the present status of the application of graphite materials to the nuclear fission reactors and fusion devices (reactors) is presented. In addition, a part of results on the related properties to the structural design and safety evaluation and results examined on the subjects that should be done in the future are also described. (author)

Nuclear materials inventory plan

International Nuclear Information System (INIS)

Doerr, R.W.; Nichols, D.H.

1982-03-01

In any processing, manufacturing, or active storage facility it is impractical to assume that any physical security system can prevent the diversion of Special Nuclear Material (SNM). It is, therefore, the responsibility of any DOE Contractor, Licensee, or other holder of SNM to provide assurance that loss or diversion of a significant quantity of SNM is detectable. This ability to detect must be accomplishable within a reasonable time interval and can be accomplished only by taking physical inventories. The information gained and decisions resulting from these inventories can be no better than the SNM accounting system and the quality of measurements performed for each receipt, removal and inventory. Inventories interrupt processing or production operations, increase personnel exposures, and can add significantly to the cost of any operation. Therefore, realistic goals for the inventory must be defined and the relationship of the inherent parameters used in its validation be determined. Purpose of this document is to provide a statement of goals and a plan of action to achieve them

CVD diamond for nuclear detection applications

CERN Document Server

Bergonzo, P; Tromson, D; Mer, C; Guizard, B; Marshall, R D; Foulon, F

2002-01-01

Chemically vapour deposited (CVD) diamond is a remarkable material for the fabrication of radiation detectors. In fact, there exist several applications where other standard semiconductor detectors do not fulfil the specific requirements imposed by corrosive, hot and/or high radiation dose environments. The improvement of the electronic properties of CVD diamond has been under intensive investigations and led to the development of a few applications that are addressing specific industrial needs. Here, we report on CVD diamond-based detector developments and we describe how this material, even though of a polycrystalline nature, is readily of great interest for applications in the nuclear industry as well as for physics experiments. Improvements in the material synthesis as well as on device fabrication especially concern the synthesis of films that do not exhibit space charge build up effects which are often encountered in CVD diamond materials and that are highly detrimental for detection devices. On a pre-i...

Licensing authority's control of radiation sources and nuclear materials in Brazil

International Nuclear Information System (INIS)

Binns, D.A.C.

2002-01-01

Full text: The Brazilian Nuclear Energy Commission is the national licensing authority and among its responsibilities is the control of nuclear materials and radiation sources. This control is carried out in three different ways: 1) Control of the import and export of nuclear materials and radiation sources. To be able to import or export any nuclear material or radiation source, the user has to have an explicit permission of the licensing authority. This is controlled by electronic means in which the user has to fill a special form found on the licensing authority's home page, where he has to fill in his name, license number, license number of his radiation protection officer and data of the material to be imported or exported. These data are checked with a data base that contains all the information of the licensed users and qualified personnel before authorization is emitted. The airport authorities have already installed x-ray machines to check all baggages entering or leaving the country. 2) Transport and transfer permit for radiation sources. In order to transport and/or transfer radiations sources and nuclear materials within the country, the user(s) have to submit an application to the licensing authority. The user(s) fill out an application form where he fills in his company's name, licensing I.D., radiation protection officer's name and I.D and identification of the sources involved. These information are checked with the licensing operations data before the operations is permitted. 3) Inspections and radiation monitoring systems. Routine and regulatory inspections are continuously carried out where the user's radiation sources and nuclear materials inventory are checked. Also the physical security and protection of these materials are verified. The installation of monitoring systems is an item that is being discussed with the airport authorities so as to increase the possibilities of detecting any illegal transport of these materials. (author)

LECI Department of Nuclear Materials

International Nuclear Information System (INIS)

2006-01-01

The LECI is a 'hot' laboratory dedicated mostly to the characterization of irradiated materials. It has, however, limited activities on fuel, as a back up to the LECA STAR in Cadarache. The LECI belongs to the Section of Research on Irradiated Materials (Department of Nuclear Materials). The Department for Nuclear Materials (DMN) has for its missions: - to contribute, through theoretical and experimental investigations, to the development of knowledge in materials science in order to be able to predict the evolution of the material physical and mechanical properties under service conditions (irradiation, thermomechanical solicitations, influence of the environment,..); - to characterize the properties of the materials used in the nuclear industry in order to determine their performance and to be able to predict their life expectancy, in particular via modelling. These materials can be irradiated or not, and originate from surveillance programs, experimental neutron irradiations or simulated irradiations with charged particles; - to establish, maintain and make use of the databases generated by these data; - to propose new or optimized materials, satisfying future service conditions and extend the life or the competitiveness of the associated systems; - to establish constitutive laws and models for the materials in service, incidental, accidental and storage conditions, and contribute to the development of the associated design codes in order to support the safety argumentation of utilities and vendors; - to provide expertise on industrial components, in particular to investigate strain or rupture mechanisms and to offer leads for improvement. This document presents, first, the purpose of the LECI (Historical data, Strategy, I and K shielded cell lines (building 605), M shielded cell line (building 625), Authorized materials). Then, it presents the microscopy and irradiation damage studies laboratory of the Saclay centre (Building 605) Which belongs to the Nuclear

International conference on security of material. Measures to prevent, intercept and respond to illicit uses of nuclear material and radioactive sources. Book of extended synopses

International Nuclear Information System (INIS)

2001-10-01

The papers cover the subjects relating to the trafficking of highly enriched nuclear materials, less radioactive, radioactive materials, radiations sources, prevention of crime, capabilities of preventing smuggling, radiation detection devices that are or should be applied on borders. Different aspects of physical protection, security and safety of nuclear materials in a number of countries are discussed. A number of papers are devoted to detectors, and measuring methods

International conference on security of material. Measures to prevent, intercept and respond to illicit uses of nuclear material and radioactive sources. Book of extended synopses

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-10-01

The papers cover the subjects relating to the trafficking of highly enriched nuclear materials, less radioactive, radioactive materials, radiations sources, prevention of crime, capabilities of preventing smuggling, radiation detection devices that are or should be applied on borders. Different aspects of physical protection, security and safety of nuclear materials in a number of countries are discussed. A number of papers are devoted to detectors, and measuring methods.

Transweb and trafficking in illicit nuclear materials: beyond the borders of physical security

International Nuclear Information System (INIS)

Ballard, J.D.; Dilger, F.

2005-01-01

Full text: Transweb is a developing threat assessment analytical protocol that uses real time GIS based assessments (a.k.a., GTA for GIS Threat Assessment) to better understand potential trafficking in illicit nuclear materials that may come from energy related sites and/or weapons production facilities. This is not a physical security protocol nor is this program a border check format like the DOE's Second Line of Defense which is designed to detect special nuclear fuels. Transweb is a tool that allows the user to look at surreptitious transportation pathways that may be used to move illicit nuclear materials after they have already breached traditional physical security barriers and allows for movement prediction and potential mitigation/intervention if they are not traveling on the highways or railways, traversing the waterways, or entering ports equipped with detecting equipment like that deployed in Second Line of Defense program. Transweb is for the real world, a world where physical security may be breached and the smugglers that capture these materials do not follow the most traveled highways, railways, or waterways in a given society. Transweb focuses on the less obvious transportation routes that may be the most likely ways that illicit nuclear materials will be transported. Thus this program offers an additional layer of security analysis not currently in use as physical protection or as border mitigation. (author)

Nuclear forensics

International Nuclear Information System (INIS)

Karadeniz, O.; Guenalp, G.

2010-01-01

This review discusses the methodology of nuclear forensics and illicit trafficking of nuclear materials. Nuclear forensics is relatively new scientific branch whose aim it is to read out material inherent from nuclear material. Nuclear forensics investigations have to be considered as part of a comprehensive set of measures for detection,interception, categorization and characterization of illicitly trafficking nuclear material. Prevention, detection and response are the main elements in combating illicit trafficking. Forensics is a key element in the response process. Forensic science is defined as the application of a broad spectrum of sciences to answer questions of interest to the legal system. Besides, in this study we will explain age determination of nuclear materials.

Material degradation - a nuclear utility's view

International Nuclear Information System (INIS)

Spekkens, P.

2007-01-01

Degradation of nuclear plant materials has been responsible for major costs and unit outage time. As such, nuclear utilities are important end users of the information produced by R and D on material degradation. This plenary describes the significance of material degradation for the nuclear utilities, and how utilities use information about material degradation in their short, medium and long term planning activities. Utilities invest in R and D programs to assist them in their business objective of operating safely, reliably and cost competitively. Material degradation impacts all three of these business drivers. Utilities make decisions on life cycle planning, unit refurbishment and 'new build' projects on the basis of their understanding of the behaviour of a variety of materials in a broad range of environments. The R and D being carried out today will determine the future business success of the nuclear utilities. The R and D program needs to be broadly based to include a range of materials, environments and time-frames, particularly any new materials proposed for use in new units. The R and D community needs to help the utility managers make choices that will result in an optimized materials R and D program

Risk Informed Approach for Nuclear Security Measures for Nuclear and Other Radioactive Material out of Regulatory Control. Implementing Guide

International Nuclear Information System (INIS)

2015-01-01

This publication provides guidance to States for developing a risk informed approach and for conducting threat and risk assessments as the basis for the design and implementation of sustainable nuclear security systems and measures for prevention of, detection of, and response to criminal and intentional unauthorised acts involving nuclear and other radioactive material out of regulatory control. It describes concepts and methodologies for a risk informed approach, including identification and assessment of threats, targets, and potential consequences; threat and risk assessment methodologies, and the use of risk informed approaches as the basis for informing the development and implementation of nuclear security systems and measures. The publication is an Implementing Guide within the IAEA Nuclear Security Series and is intended for use by national policy makers, law enforcement agencies and experts from competent authorities and other relevant organizations involved in the establishment, implementation, maintenance or sustainability of nuclear security systems and measures related to nuclear and other radioactive material out of regulatory control

Nuclear material control in Brazil

International Nuclear Information System (INIS)

Marzo, M.A.S.; Iskin, M.C.L.; Palhares, L.C.; Almeida, S.G. de.

1988-01-01

A general view about the safeguards activities in Brazil is presented. The national system of accounting for and control of nuclear materials is described. The safeguards agreements signed by Brazil are presented, the facilities and nuclear material under these agreements are listed, and the dificulties on the pratical implementation are discussed. (E.G.) [pt

Modeling most likely pathways for smuggling radioactive and special nuclear materials on a worldwide multimodal transportation network

Energy Technology Data Exchange (ETDEWEB)

Saeger, Kevin J [Los Alamos National Laboratory; Cuellar, Leticia [Los Alamos National Laboratory

2010-01-01

Nuclear weapons proliferation is an existing and growing worldwide problem. To help with devising strategies and supporting decisions to interdict the transport of nuclear material, we developed the Pathway Analysis, Threat Response and Interdiction Options Tool (PATRIOT) that provides an analytical approach for evaluating the probability that an adversary smuggling radioactive or special nuclear material will be detected during transit. We incorporate a global, multi-modal transportation network, explicit representation of designed and serendipitous detection opportunities, and multiple threat devices, material types, and shielding levels. This paper presents the general structure of PATRIOT, and focuses on the theoretical framework used to model the reliabilities of all network components that are used to predict the most likely pathways to the target.

Standard guide for application of radiation monitors to the control and physical security of special nuclear material

International Nuclear Information System (INIS)

Anon.

1989-01-01

This guide briefly describes the state-of-the-art of radiation monitors for detecting special nuclear material (SNM) in order to establish the context in which to write performance standards for the monitors. This guide extracts information from technical documentation to provide information for selecting, calibrating, testing, and operating such radiation monitors when they are used for the control and protection of SNM. This guide offers an unobtrusive means of searching pedestrians, packages, and motor vehicles for concealed SNM as one part of a nuclear material control or security plan for nuclear materials. The radiation monitors can provide an efficient, sensitive, and reliable means of detecting the theft of small quantities of SNM while maintaining a low likelihood of nuisance alarms

Intelligent data-acquisition instrumentation for special nuclear material assay data analysis

International Nuclear Information System (INIS)

Ethridge, C.D.

1980-01-01

The Detection, Surveillance, Verification, and Recovery Group of the Los Alamos Scientific Laboratory Energy Division/Nuclear Safeguards Programs is now utilizing intelligent data-acquisition instrumentation for assay data analysis of special nuclear material. The data acquisition and analysis are enabled by the incorporation of a number-crunching microprocessor sequenced by a single component microcomputer. Microcomputer firmware establishes the capability for processing the computation of several selected functions and also the ability of instrumentation self-diagnostics

Radiation Effects in Nuclear Waste Materials

International Nuclear Information System (INIS)

Weber, William J.; Wang, Lumin; Hess, Nancy J.; Icenhower, Jonathan P.; Thevuthasan, Suntharampillai

2003-01-01

The objective of this project is to develop a fundamental understanding of radiation effects in glasses and ceramics, as well as the influence of solid-state radiation effects on aqueous dissolution kinetics, which may impact the performance of nuclear waste forms and stabilized nuclear materials. This work provides the underpinning science to develop improved glass and ceramic waste forms for the immobilization and disposition of high-level tank waste, excess plutonium, plutonium residues and scrap, other actinides, and other nuclear waste streams. Furthermore, this work is developing develop predictive models for the performance of nuclear waste forms and stabilized nuclear materials. Thus, the research performed under this project has significant implications for the immobilization of High-Level Waste (HLW) and Nuclear Materials, two mission areas within the Office of Environmental Management (EM). With regard to the HLW mission, this research will lead to improved understanding of radiation-induced degradation mechanisms and their effects on dissolution kinetics, as well as development of predictive models for waste form performance. In the Nuclear Materials mission, this research will lead to improvements in the understanding of radiation effects on the chemical and structural properties of materials for the stabilization and long-term storage of plutonium, highly-enriched uranium, and other actinides. The research uses plutonium incorporation, ion-beam irradiation, and electron-beam irradiation to simulate the effects of alpha decay and beta decay on relevant glasses and ceramics. The research under this project has the potential to result in improved glass and ceramic materials for the stabilization and immobilization of high-level tank waste, plutonium residues and scraps, surplus weapons plutonium, highly-enriched uranium, other actinides, and other radioactive materials

Radiation Effects in Nuclear Waste Materials

International Nuclear Information System (INIS)

Weber, William J.

2005-01-01

The objective of this project is to develop a fundamental understanding of radiation effects in glasses and ceramics, as well as the influence of solid-state radiation effects on aqueous dissolution kinetics, which may impact the performance of nuclear waste forms and stabilized nuclear materials. This work provides the underpinning science to develop improved glass and ceramic waste forms for the immobilization and disposition of high-level tank waste, excess plutonium, plutonium residues and scrap, other actinides, and other nuclear waste streams. Furthermore, this work is developing develop predictive models for the performance of nuclear waste forms and stabilized nuclear materials. Thus, the research performed under this project has significant implications for the immobilization of High-Level Waste (HLW) and Nuclear Materials, two mission areas within the Office of Environmental Management (EM). With regard to the HLW mission, this research will lead to improved understanding of radiation-induced degradation mechanisms and their effects on dissolution kinetics, as well as development of predictive models for waste form performance. In the Nuclear Materials mission, this research will lead to improvements in the understanding of radiation effects on the chemical and structural properties of materials for the stabilization and long-term storage of plutonium, highly-enriched uranium, and other actinides. The research uses plutonium incorporation, ion-beam irradiation, and electron-beam irradiation to simulate the effects of alpha decay and beta decay on relevant glasses and ceramics. The research under this project has the potential to result in improved glass and ceramic materials for the stabilization and immobilization of high-level tank waste, plutonium residues and scraps, surplus weapons plutonium, highly-enriched uranium, other actinides, and other radioactive materials

International dimension of illicit trafficking in nuclear and other radioactive material

International Nuclear Information System (INIS)

Zaitseva, L.; Bunn, G.; Steinhaeusler, F.

2002-01-01

Full text: Illicit trafficking in nuclear and other radioactive material is primarily associated with Russia and other former Soviet republics. Indeed, with the collapse of the former Soviet Union (FSU) in 1991, hundreds of tons of weapons-usable nuclear material and thousands of radiation sources were left without adequate control and protection, thus posing a risk for sabotage, theft and diversion. Out of 700 illicit trafficking incidents recorded in the Stanford's database on nuclear smuggling, theft and orphan radiation sources (DSTO), over 450 either took place in the former Soviet Union or involved material that had reportedly originated from the FSU. In the period 1992-1994, Western and Eastern Europe were heavily affected by the inflow of nuclear material smuggled from the FSU. Since then, various measures were taken by the European countries and former Soviet republics to prevent the trafficking of radioactive substances ranging from the improvement of physical security at nuclear facilities to the installation of detection equipment at international borders. However, although the number of illicit trafficking incidents in Western Europe has decreased dramatically since 1994 and the overall annual number of such cases has been lower than in 1994, evidence suggests that diverted nuclear material is still being smuggled out of the FSU. An increased number of interceptions of nuclear and other radioactive material in the Caucasus, Turkey and Central Asia, well-known for their drugs and arms smuggling routes, over the past three years demonstrates that the material may now be moving south rather than west. This is particularly alarming considering the proximity of three countries to the potential end-users of nuclear and other radioactive material, such as AI Qaida terrorist network and aspiring nuclear weapon states in the Middle East. Although the FSU remains the major potential source of nuclear and other radioactive material, it is not the only one. Thefts

Nuclear materials transport worldwide

International Nuclear Information System (INIS)

Stellpflug, J.

1987-01-01

This Greenpeace report shows: nuclear materials transport is an extremely hazardous business. There is no safe protection against accidents, kidnapping, or sabotage. Any moment of a day, at any place, a nuclear transport accident may bring the world to disaster, releasing plutonium or radioactive fission products to the environment. Such an event is not less probable than the MCA at Chernobyl. The author of the book in hand follows the secret track of radioactive materials around the world, from uranium mines to the nuclear power plants, from reprocessing facilities to the waste repositories. He explores the routes of transport and the risks involved, he gives the names of transport firms and discloses incidents and carelessness, tells about damaged waste drums and plutonium that 'disappeared'. He also tells about worldwide, organised resistance to such nuclear transports, explaining the Greenpeace missions on the open sea, or the 'day X' operation at the Gorleben site, informing the reader about protests and actions for a world freed from the threat of nuclear energy. (orig./HP) [de

Fundamentals of materials accounting for nuclear safeguards

Energy Technology Data Exchange (ETDEWEB)

Pillay, K.K.S. (comp.)

1989-04-01

Materials accounting is essential to providing the necessary assurance for verifying the effectiveness of a safeguards system. The use of measurements, analyses, records, and reports to maintain knowledge of the quantities of nuclear material present in a defined area of a facility and the use of physical inventories and materials balances to verify the presence of special nuclear materials are collectively known as materials accounting for nuclear safeguards. This manual, prepared as part of the resource materials for the Safeguards Technology Training Program of the US Department of Energy, addresses fundamental aspects of materials accounting, enriching and complementing them with the first-hand experiences of authors from varied disciplines. The topics range from highly technical subjects to site-specific system designs and policy discussions. This collection of papers is prepared by more than 25 professionals from the nuclear safeguards field. Representing research institutions, industries, and regulatory agencies, the authors create a unique resource for the annual course titled ''Materials Accounting for Nuclear Safeguards,'' which is offered at the Los Alamos National Laboratory.

Exploring laser-induced breakdown spectroscopy for nuclear materials analysis and in-situ applications

International Nuclear Information System (INIS)

Martin, Madhavi Z.; Allman, Steve; Brice, Deanne J.; Martin, Rodger C.; Andre, Nicolas O.

2012-01-01

Laser-induced breakdown spectroscopy (LIBS) has been used to determine the limits of detection of strontium (Sr) and cesium (Cs), common nuclear fission products. Additionally, detection limits were determined for cerium (Ce), often used as a surrogate for radioactive plutonium in laboratory studies. Results were obtained using a laboratory instrument with a Nd:YAG laser at fundamental wavelength of 1064 nm, frequency doubled to 532 nm with energy of 50 mJ/pulse. The data was compared for different concentrations of Sr and Ce dispersed in a CaCO 3 (white) and carbon (black) matrix. We have addressed the sampling errors, limits of detection, reproducibility, and accuracy of measurements as they relate to multivariate analysis in pellets that were doped with the different elements at various concentrations. These results demonstrate that LIBS technique is inherently well suited for in situ analysis of nuclear materials in hot cells. Three key advantages are evident: (1) small samples (mg) can be evaluated; (2) nuclear materials can be analyzed with minimal sample preparation; and (3) samples can be remotely analyzed very rapidly (ms-seconds). Our studies also show that the methods can be made quantitative. Very robust multivariate models have been used to provide quantitative measurement and statistical evaluation of complex materials derived from our previous research on wood and soil samples. - Highlights: ► Did the detection of strontium, cerium, and cesium in CaCO 3 and graphite matrices. ► The detection of these elements was performed in a systematic manner. ► Univariate calibration curves were used to determine strontium detection. ► Univariate and multivariate statistical analysis built improved statistical models. ► Limits of detection are comparable or better in case of cerium and cesium.

Nuclear Forensic Science: Analysis of Nuclear Material Out of Regulatory Control

Science.gov (United States)

Kristo, Michael J.; Gaffney, Amy M.; Marks, Naomi; Knight, Kim; Cassata, William S.; Hutcheon, Ian D.

2016-06-01

Nuclear forensic science seeks to identify the origin of nuclear materials found outside regulatory control. It is increasingly recognized as an integral part of a robust nuclear security program. This review highlights areas of active, evolving research in nuclear forensics, with a focus on analytical techniques commonly employed in Earth and planetary sciences. Applications of nuclear forensics to uranium ore concentrates (UOCs) are discussed first. UOCs have become an attractive target for nuclear forensic researchers because of the richness in impurities compared to materials produced later in the fuel cycle. The development of chronometric methods for age dating nuclear materials is then discussed, with an emphasis on improvements in accuracy that have been gained from measurements of multiple radioisotopic systems. Finally, papers that report on casework are reviewed, to provide a window into current scientific practice.

Active Interrogation using Photofission Technique for Nuclear Materials Control and Accountability

Energy Technology Data Exchange (ETDEWEB)

Yang, Haori [Oregon State Univ., Corvallis, OR (United States)

2016-03-31

Innovative systems with increased sensitivity and resolution are in great demand to detect diversion and to prevent misuse in support of nuclear materials management for the U.S. fuel cycle. Nuclear fission is the most important multiplicative process involved in non-destructive active interrogation. This process produces the most easily recognizable signature for nuclear materials. In addition to thermal or high-energy neutrons, high-energy gamma rays can also excite a nucleus and cause fission through a process known as photofission. Electron linear accelerators (linacs) are widely used as the interrogating photon sources for inspection methods involving photofission technique. After photofission reactions, prompt signals are much stronger than the delayed signals, but it is difficult to quantify them in practical measurements. Delayed signals are easily distinguishable from the interrogating radiation. Linac-based, advanced inspection techniques utilizing the delayed signals after photofission have been extensively studied for homeland security applications. Previous research also showed that a unique delayed gamma ray energy spectrum exists for each fissionable isotope. In this work, high-energy delayed γ-rays were demonstrated to be signatures for detection, identification, and quantification of special nuclear materials. Such γ-rays were measured in between linac pulses using independent data acquisition systems. A list-mode system was developed to measure low-energy delayed γ-rays after irradiation. Photofission product yields of ²³⁸U and ²³⁹Pu were determined based on the measured delayed γ-ray spectra. The differential yields of delayed γ-rays were also proven to be able to discriminate nuclear from non-nuclear materials. The measurement outcomes were compared with Monte Carlo simulation results. It was demonstrated that the current available codes have capabilities and limitations in the simulation of photofission process. A two

Active Interrogation using Photofission Technique for Nuclear Materials Control and Accountability

International Nuclear Information System (INIS)

Yang, Haori

2016-01-01

Innovative systems with increased sensitivity and resolution are in great demand to detect diversion and to prevent misuse in support of nuclear materials management for the U.S. fuel cycle. Nuclear fission is the most important multiplicative process involved in non-destructive active interrogation. This process produces the most easily recognizable signature for nuclear materials. In addition to thermal or high-energy neutrons, high-energy gamma rays can also excite a nucleus and cause fission through a process known as photofission. Electron linear accelerators (linacs) are widely used as the interrogating photon sources for inspection methods involving photofission technique. After photofission reactions, prompt signals are much stronger than the delayed signals, but it is difficult to quantify them in practical measurements. Delayed signals are easily distinguishable from the interrogating radiation. Linac-based, advanced inspection techniques utilizing the delayed signals after photofission have been extensively studied for homeland security applications. Previous research also showed that a unique delayed gamma ray energy spectrum exists for each fissionable isotope. In this work, high-energy delayed γ-rays were demonstrated to be signatures for detection, identification, and quantification of special nuclear materials. Such γ-rays were measured in between linac pulses using independent data acquisition systems. A list-mode system was developed to measure low-energy delayed γ-rays after irradiation. Photofission product yields of 238 U and 239 Pu were determined based on the measured delayed γ-ray spectra. The differential yields of delayed γ-rays were also proven to be able to discriminate nuclear from non-nuclear materials. The measurement outcomes were compared with Monte Carlo simulation results. It was demonstrated that the current available codes have capabilities and limitations in the simulation of photofission process. A two-fold approach was

The century of nuclear materials

Science.gov (United States)

Mansur, Lou; Was, Gary S.; Zinkle, Steve; Petti, David; Ukai, Shigeharu

2018-03-01

In the spring of 1959 the well-read metallurgist would have noticed the first issue of an infant Journal, one dedicated to a unique and fast growing field of materials issues associated with nuclear energy systems. The periodical, Journal of Nuclear Materials (JNM), is now the leading publication in the field from which it takes its name, thriving beyond the rosiest expectations of its founders. The discipline is well into the second half-century. During that time much has been achieved in nuclear materials; the Journal provides the authoritative record of virtually all those accomplishments. These pages introduce the 500th volume, a significant measure in the world of publishing. The Editors reflect on the progress in the field and the role of this journal.

Safeguards on nuclear materials

International Nuclear Information System (INIS)

Cisar, V.; Keselica, M.; Bezak, S.

2001-01-01

The article describes the implementation of IAEA safeguards for nuclear materials in the Czech and Slovak Republics, the establishment and development of the State System of Accounting for and Control of Nuclear Material (SSAC) at the levels of the state regulatory body and of the operator, particularly at the Dukovany nuclear power plant. A brief overview of the historical development is given. Attention is concentrated on the basic concepts and legal regulation accepted by the Czech and Slovak Republics in accordance with the new approach to create a complete legislative package in the area of nuclear energy uses. The basic intention is to demonstrate the functions of the entire system, including safeguards information processing and technical support of the system. Perspectives of the Integrated Safeguards System are highlighted. The possible ways for approximation of the two national systems to the Safeguards System within the EU (EURATOM) are outlined, and the necessary regulatory and operators' roles in this process are described. (author)

The Physical Protection of Nuclear Material

International Nuclear Information System (INIS)

1993-09-01

Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers [es

The Physical Protection of Nuclear Material

International Nuclear Information System (INIS)

1993-09-01

Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers [fr

The Physical Protection of Nuclear Material

International Nuclear Information System (INIS)

1993-01-01

Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers

The Physical Protection of Nuclear Material

International Nuclear Information System (INIS)

1993-09-01

Physical protection against the theft or unauthorized diversion of nuclear materials and against the sabotage of nuclear facilities by individuals or groups has long been a matter of national and international concern. Although responsibility for establishing and operating a comprehensive physical protection system for nuclear materials and facilities within a State rests entirely with the Government of that State, it is not a matter of indifference to other States whether and to what extent that responsibility is fulfilled. Physical protection has therefore become a matter of international concern and co-operation. The need for international cooperation becomes evident in situations where the effectiveness of physical protection in one State depends on the taking by other States also of adequate measures to deter or defeat hostile actions against nuclear facilities and materials, particularly when such materials are transported across national frontiers

Nuclear materials facility safety initiative

International Nuclear Information System (INIS)

Peddicord, K.L.; Nelson, P.; Roundhill, M.; Jardine, L.J.; Lazarev, L.; Moshkov, M.; Khromov, V.V.; Kruchkov, E.; Bolyatko, V.; Kazanskij, Yu.; Vorobeva, I.; Lash, T.R.; Newton, D.; Harris, B.

2000-01-01

Safety in any facility in the nuclear fuel cycle is a fundamental goal. However, it is recognized that, for example, should an accident occur in either the U.S. or Russia, the results could seriously delay joint activities to store and disposition weapons fissile materials in both countries. To address this, plans are underway jointly to develop a nuclear materials facility safety initiative. The focus of the initiative would be to share expertise which would lead in improvements in safety and safe practices in the nuclear fuel cycle.The program has two components. The first is a lab-to-lab initiative. The second involves university-to-university collaboration.The lab-to-lab and university-to-university programs will contribute to increased safety in facilities dealing with nuclear materials and related processes. These programs will support important bilateral initiatives, develop the next generation of scientists and engineers which will deal with these challenges, and foster the development of a safety culture

Modernizing computerized nuclear material accounting systems

International Nuclear Information System (INIS)

Erkkila, B.H.; Claborn, J.

1995-01-01

DOE Orders and draft orders for nuclear material control and accountability address a complete material control and accountability (MC and A) program for all DOE contractors processing, using, or storing nuclear materials. A critical element of an MC and A program is the accounting system used to track and record all inventories of nuclear material and movements of materials in those inventories. Most DOE facilities use computerized accounting systems to facilitate the task of accounting for all their inventory of nuclear materials. Many facilities still use a mixture of a manual paper system with a computerized system. Also, facilities may use multiple systems to support information needed for MC and A. For real-time accounting it is desirable to implement a single integrated data base management system for a variety of users. In addition to accountability needs, waste management, material management, and production operations must be supported. Information in these systems can also support criticality safety and other safety issues. Modern networked microcomputers provide extensive processing and reporting capabilities that single mainframe computer systems struggle with. This paper describes an approach being developed at Los Alamos to address these problems

Reducing nuclear danger through intergovernmental technical exchanges on nuclear materials safety management

International Nuclear Information System (INIS)

Jardine, L.J.; Peddicord, K.L.; Witmer, F.E.; Krumpe, P.F.; Lazarev, L.; Moshkov, M.

1997-01-01

The United States and Russia are dismantling nuclear weapons and generating hundreds of tons of excess plutonium and high enriched uranium fissile nuclear materials that require disposition. The U.S. Department of Energy and Russian Minatom organizations.are planning and implementing safe, secure storage and disposition operations for these materials in numerous facilities. This provides a new opportunity for technical exchanges between Russian and Western scientists that can establish an improved and sustained common safety culture for handling these materials. An initiative that develops and uses personal relationships and joint projects among Russian and Western participants involved in fissile nuclear materials safety management contributes to improving nuclear materials nonproliferation and to making a safer world. Technical exchanges and workshops are being used to systematically identify opportunities in the nuclear fissile materials facilities to improve and ensure the safety of workers, the public, and the environment

Nuclear materials identification by photon interrogation

International Nuclear Information System (INIS)

Pozzi, S.A.; Monville, M.; Padovani, E.

2005-01-01

We describe a preliminary modification to the Monte Carlo codes MCNP-X and MCNP-PoliMi that is aimed at simulating the neutron and photon field generated by interrogating fissile (and non-fissile) material with a high energy photon source. Photo-atomic and photo-nuclear collisions are modeled, with particular emphasis on the generation of secondary particles that are emitted as a result of these interactions. The simulations can be used to design and analyze measurements that are performed in a wide variety of scenarios. An application of the methodology to the interrogation of packages on a luggage belt conveyor is presented. Preliminary results show that it is possible to detect 5 Kg of highly enriched uranium in a package by measuring the correlation function between 2 detectors. This correlation function is based on the detection of prompt radiation from photonuclear events

System for detecting nuclear explosions

International Nuclear Information System (INIS)

Rawls, L.E.

1978-01-01

Apparatus for detecting underground nuclear explosions is described that is comprised of an antenna located in the dielectric substance of a deep waveguide in the earth and adapted to detect low frequency electromagnetic waves generated by a nuclear explosion, the deep waveguide comprising the high conductivity upper sedimentary layers of the earth, the dielectric basement rock, and a high conductivity layer of basement rock due to the increased temperature thereof at great depths, and means for receiving the electromagnetic waves detected by said antenna means

Exploring laser-induced breakdown spectroscopy for nuclear materials analysis and in-situ applications

Science.gov (United States)

Martin, Madhavi Z.; Allman, Steve; Brice, Deanne J.; Martin, Rodger C.; Andre, Nicolas O.

2012-08-01

Laser-induced breakdown spectroscopy (LIBS) has been used to determine the limits of detection of strontium (Sr) and cesium (Cs), common nuclear fission products. Additionally, detection limits were determined for cerium (Ce), often used as a surrogate for radioactive plutonium in laboratory studies. Results were obtained using a laboratory instrument with a Nd:YAG laser at fundamental wavelength of 1064 nm, frequency doubled to 532 nm with energy of 50 mJ/pulse. The data was compared for different concentrations of Sr and Ce dispersed in a CaCO3 (white) and carbon (black) matrix. We have addressed the sampling errors, limits of detection, reproducibility, and accuracy of measurements as they relate to multivariate analysis in pellets that were doped with the different elements at various concentrations. These results demonstrate that LIBS technique is inherently well suited for in situ analysis of nuclear materials in hot cells. Three key advantages are evident: (1) small samples (mg) can be evaluated; (2) nuclear materials can be analyzed with minimal sample preparation; and (3) samples can be remotely analyzed very rapidly (ms-seconds). Our studies also show that the methods can be made quantitative. Very robust multivariate models have been used to provide quantitative measurement and statistical evaluation of complex materials derived from our previous research on wood and soil samples.

Investigations of active interrogation techniques to detect special nuclear material in maritime environments: Standoff interrogation of small- and medium-sized cargo ships

Energy Technology Data Exchange (ETDEWEB)

Miller, Thomas M., E-mail: millertm@ornl.gov; Patton, Bruce W.; Grogan, Brandon R.; Henkel, James J.; Murphy, Brian D.; Johnson, Jeffrey O.; Mihalczo, John T.

2013-12-01

In this work, several active interrogation (AI) sources are evaluated to determine their usefulness in detecting the presence of special nuclear material (SNM) in fishing trawlers, small cargo transport ships, and luxury yachts at large standoff distances from the AI source and detector. This evaluation is performed via computational analysis applying Monte Carlo methods with advanced variance reduction techniques. The goal is to determine the AI source strength required to detect the presence of SNM. The general conclusion of this study is that AI is not reliable when SNM is heavily shielded and not tightly coupled geometrically with the source and detector, to the point that AI should not be considered a via interrogation option in these scenarios. More specifically, when SNM is shielded by hydrogenous material large AI source strengths are required if detection is based on neutrons, which is not surprising. However, if the SNM is shielded by high-Z material the required AI source strengths are not significantly different if detection is based on neutrons or photons, which is somewhat surprising. Furthermore, some of the required AI source strengths that were calculated are very large. These results coupled with the realities of two ships moving independently at sea and other assumptions made during this analysis make the use of standoff AI in the maritime environment impractical.

Investigations of active interrogation techniques to detect special nuclear material in maritime environments: Standoff interrogation of small- and medium-sized cargo ships

International Nuclear Information System (INIS)

Miller, Thomas M.; Patton, Bruce W.; Grogan, Brandon R.; Henkel, James J.; Murphy, Brian D.; Johnson, Jeffrey O.; Mihalczo, John T.

2013-01-01

In this work, several active interrogation (AI) sources are evaluated to determine their usefulness in detecting the presence of special nuclear material (SNM) in fishing trawlers, small cargo transport ships, and luxury yachts at large standoff distances from the AI source and detector. This evaluation is performed via computational analysis applying Monte Carlo methods with advanced variance reduction techniques. The goal is to determine the AI source strength required to detect the presence of SNM. The general conclusion of this study is that AI is not reliable when SNM is heavily shielded and not tightly coupled geometrically with the source and detector, to the point that AI should not be considered a via interrogation option in these scenarios. More specifically, when SNM is shielded by hydrogenous material large AI source strengths are required if detection is based on neutrons, which is not surprising. However, if the SNM is shielded by high-Z material the required AI source strengths are not significantly different if detection is based on neutrons or photons, which is somewhat surprising. Furthermore, some of the required AI source strengths that were calculated are very large. These results coupled with the realities of two ships moving independently at sea and other assumptions made during this analysis make the use of standoff AI in the maritime environment impractical

A survey of infrared technology for special nuclear materials control and accounting

International Nuclear Information System (INIS)

Stanbro, W.D.; Leonard, R.S.; Steverson, C.A.; Angerman, M.I.

1992-03-01

This report reviews some aspects of current infrared measurement technology and suggests two applications in which it may be used in nuclear safeguards. These applications include both materials control and materials accounting. In each case, the measurements rely on passive detection of infrared radiation generated from the heat produced by the radioactive decay of plutonium. Both imaging and non-imaging techniques are discussed

Variance and covariance calculations for nuclear materials accounting using ''MAVARIC''

International Nuclear Information System (INIS)

Nasseri, K.K.

1987-07-01

Determination of the detection sensitivity of a materials accounting system to the loss of special nuclear material (SNM) requires (1) obtaining a relation for the variance of the materials balance by propagation of the instrument errors for the measured quantities that appear in the materials balance equation and (2) substituting measured values and their error standard deviations into this relation and calculating the variance of the materials balance. MAVARIC (Materials Accounting VARIance Calculations) is a custom spreadsheet, designed using the second release of Lotus 1-2-3, that significantly reduces the effort required to make the necessary variance (and covariance) calculations needed to determine the detection sensitivity of a materials accounting system. Predefined macros within the spreadsheet allow the user to carry out long, tedious procedures with only a few keystrokes. MAVARIC requires that the user enter the following data into one of four data tables, depending on the type of the term in the materials balance equation; the SNM concentration, the bulk mass (or solution volume), the measurement error standard deviations, and the number of measurements made during an accounting period. The user can also specify if there are correlations between transfer terms. Based on these data entries, MAVARIC can calculate the variance of the materials balance and the square root of this variance, from which the detection sensitivity of the accounting system can be determined

Variance and covariance calculations for nuclear materials accounting using 'MAVARIC'

International Nuclear Information System (INIS)

Nasseri, K.K.

1987-01-01

Determination of the detection sensitivity of a materials accounting system to the loss of special nuclear material (SNM) requires (1) obtaining a relation for the variance of the materials balance by propagation of the instrument errors for the measured quantities that appear in the materials balance equation and (2) substituting measured values and their error standard deviations into this relation and calculating the variance of the materials balance. MAVARIC (Materials Accounting VARIance Calculations) is a custom spreadsheet, designed using the second release of Lotus 1-2-3, that significantly reduces the effort required to make the necessary variance (and covariance) calculations needed to determine the detection sensitivity of a materials accounting system. Predefined macros within the spreadsheet allow the user to carry out long, tedious procedures with only a few keystrokes. MAVARIC requires that the user enter the following data into one of four data tables, depending on the type of the term in the materials balance equation; the SNM concentration, the bulk mass (or solution volume), the measurement error standard deviations, and the number of measurements made during an accounting period. The user can also specify if there are correlations between transfer terms. Based on these data entries, MAVARIC can calculate the variance of the materials balance and the square root of this variance, from which the detection sensitivity of the accounting system can be determined

Regulation on control of nuclear fuel materials

International Nuclear Information System (INIS)

Ikeda, Kaname

1976-01-01

Some comment is made on the present laws and the future course of consolidating the regulation of nuclear fuel materials. The first part gives the definitions of the nuclear fuel materials in the laws. The second part deals with the classification and regulation in material handling. Refinement undertaking, fabrication undertaking, reprocessing undertaking, the permission of the government to use the materials, the permission of the government to use the materials under international control, the restriction of transfer and receipt, the reporting, and the safeguard measures are commented. The third part deals with the strengthening of regulation. The nuclear fuel safety deliberation special committee will be established at some opportunity of revising the ordinance. The nuclear material safeguard special committee has been established in the Atomic Energy Commission. The last part deals with the future course of legal consolidation. The safety control will be strengthened. The early investigation of waste handling is necessary, because low level solid wastes are accumulating at each establishment. The law for transporting nuclear materials must be consolidated as early as possible to correspond to foreign transportation laws. Physical protection is awaiting the conclusions of the nuclear fuel safeguard special committee. The control and information systems for the safeguard measures must be consolidated in the laws. (Iwakiri, K.)

The nuclear car wash: A system to detect nuclear weapons in commercial cargo shipments

Science.gov (United States)

Slaughter, D. R.; Accatino, M. R.; Bernstein, A.; Biltoft, P.; Church, J. A.; Descalle, M. A.; Hall, J. M.; Manatt, D. R.; Mauger, G. J.; Moore, T. L.; Norman, E. B.; Petersen, D. C.; Pruet, J. A.; Prussin, S. G.

2007-08-01

A concept for detecting the presence of special nuclear material ( 235U or 239Pu) concealed in intermodal cargo containers has been developed, studied, and recent performance results are described. It is based on interrogation with a pulsed beam of 3-7 MeV neutrons that produce fission events and subsequent detection of their β-delayed neutron emission or β-delayed high-energy γ-radiation reveals the presence of fissionable material. Fission product β-delayed γ-rays above 3 MeV are nearly 10 times more abundant than β-delayed neutrons and are distinct from natural radioactivity and from nearly all of the induced activity in a normal cargo. Detector backgrounds and potential interferences with the fission signature radiation have been identified and quantified. Their impact on detection sensitivity is relatively minor and can be addressed readily. Components of a simple laboratory prototype have been assembled, tested with the most challenging cargo threat scenarios, and results compared to computer simulations. Preliminary results will be presented.

The nuclear car wash: A system to detect nuclear weapons in commercial cargo shipments

International Nuclear Information System (INIS)

Slaughter, D.R.; Accatino, M.R.; Bernstein, A.; Biltoft, P.; Church, J.A.; Descalle, M.A.; Hall, J.M.; Manatt, D.R.; Mauger, G.J.; Moore, T.L.; Norman, E.B.; Petersen, D.C.; Pruet, J.A.; Prussin, S.G.

2007-01-01

A concept for detecting the presence of special nuclear material ( 235 U or 239 Pu) concealed in intermodal cargo containers has been developed, studied, and recent performance results are described. It is based on interrogation with a pulsed beam of 3-7 MeV neutrons that produce fission events and subsequent detection of their β-delayed neutron emission or β-delayed high-energy γ-radiation reveals the presence of fissionable material. Fission product β-delayed γ-rays above 3 MeV are nearly 10 times more abundant than β-delayed neutrons and are distinct from natural radioactivity and from nearly all of the induced activity in a normal cargo. Detector backgrounds and potential interferences with the fission signature radiation have been identified and quantified. Their impact on detection sensitivity is relatively minor and can be addressed readily. Components of a simple laboratory prototype have been assembled, tested with the most challenging cargo threat scenarios, and results compared to computer simulations. Preliminary results will be presented

Tracer techniques in estimating nuclear materials holdup

International Nuclear Information System (INIS)

Pillay, K.K.S.

1987-01-01

Residual inventory of nuclear materials remaining in processing facilities (holdup) is recognized as an insidious problem for safety of plant operations and safeguarding of special nuclear materials (SNM). This paper reports on an experimental study where a well-known method of radioanalytical chemistry, namely tracer technique, was successfully used to improve nondestructive measurements of holdup of nuclear materials in a variety of plant equipment. Such controlled measurements can improve the sensitivity of measurements of residual inventories of nuclear materials in process equipment by several orders of magnitude and the good quality data obtained lend themselves to developing mathematical models of holdup of SNM during stable plant operations

Modeling most likely pathways for smuggling radioactive and special nuclear materials on a worldwide multi-modal transportation network

Energy Technology Data Exchange (ETDEWEB)

Saeger, Kevin J [Los Alamos National Laboratory; Cuellar, Leticia [Los Alamos National Laboratory

2010-10-28

Nuclear weapons proliferation is an existing and growing worldwide problem. To help with devising strategies and supporting decisions to interdict the transport of nuclear material, we developed the Pathway Analysis, Threat Response and Interdiction Options Tool (PATRIOT) that provides an analytical approach for evaluating the probability that an adversary smuggling radioactive or special nuclear material will be detected during transit. We incorporate a global, multi-modal transportation network, explicit representation of designed and serendipitous detection opportunities, and multiple threat devices, material types, and shielding levels. This paper presents the general structure of PATRIOT, all focuses on the theoretical framework used to model the reliabilities of all network components that are used to predict the most likely pathways to the target.

Certified reference materials and reference methods for nuclear safeguards and security.

Science.gov (United States)

Jakopič, R; Sturm, M; Kraiem, M; Richter, S; Aregbe, Y

2013-11-01

Confidence in comparability and reliability of measurement results in nuclear material and environmental sample analysis are established via certified reference materials (CRMs), reference measurements, and inter-laboratory comparisons (ILCs). Increased needs for quality control tools in proliferation resistance, environmental sample analysis, development of measurement capabilities over the years and progress in modern analytical techniques are the main reasons for the development of new reference materials and reference methods for nuclear safeguards and security. The Institute for Reference Materials and Measurements (IRMM) prepares and certifices large quantities of the so-called "large-sized dried" (LSD) spikes for accurate measurement of the uranium and plutonium content in dissolved nuclear fuel solutions by isotope dilution mass spectrometry (IDMS) and also develops particle reference materials applied for the detection of nuclear signatures in environmental samples. IRMM is currently replacing some of its exhausted stocks of CRMs with new ones whose specifications are up-to-date and tailored for the demands of modern analytical techniques. Some of the existing materials will be re-measured to improve the uncertainties associated with their certified values, and to enable laboratories to reduce their combined measurement uncertainty. Safeguards involve the quantitative verification by independent measurements so that no nuclear material is diverted from its intended peaceful use. Safeguards authorities pay particular attention to plutonium and the uranium isotope (235)U, indicating the so-called 'enrichment', in nuclear material and in environmental samples. In addition to the verification of the major ratios, n((235)U)/n((238)U) and n((240)Pu)/n((239)Pu), the minor ratios of the less abundant uranium and plutonium isotopes contain valuable information about the origin and the 'history' of material used for commercial or possibly clandestine purposes, and

Enhancing nuclear quadrupole resonance (NQR) signature detection leveraging interference suppression algorithms

Science.gov (United States)

DeBardelaben, James A.; Miller, Jeremy K.; Myrick, Wilbur L.; Miller, Joel B.; Gilbreath, G. Charmaine; Bajramaj, Blerta

2012-06-01

Nuclear quadrupole resonance (NQR) is a radio frequency (RF) magnetic spectroscopic technique that has been shown to detect and identify a wide range of explosive materials containing quadrupolar nuclei. The NQR response signal provides a unique signature of the material of interest. The signal is, however, very weak and can be masked by non-stationary RF interference (RFI) and thermal noise, limiting detection distance. In this paper, we investigate the bounds on the NQR detection range for ammonium nitrate. We leverage a low-cost RFI data acquisition system composed of inexpensive B-field sensing and commercial-off-the-shelf (COTS) software-defined radios (SDR). Using collected data as RFI reference signals, we apply adaptive filtering algorithms to mitigate RFI and enable NQR detection techniques to approach theoretical range bounds in tactical environments.

Summary Report for the Radiation Detection for Nuclear Security Summer School 2012

Energy Technology Data Exchange (ETDEWEB)

Runkle, Robert C.; Baciak, James E.; Stave, Jean A.

2012-08-22

The Pacific Northwest National Laboratory (PNNL) hosted students from across the United States at the inaugural Radiation Detection for Nuclear Security Summer School from June 11 – 22, 2012. The summer school provided students with a unique understanding of nuclear security challenges faced in the field and exposed them to the technical foundations, analyses, and insight that will be required by future leaders in technology development and implementation. The course heavily emphasized laboratory and field demonstrations including direct measurements of special nuclear material. The first week of the summer school focused on the foundational knowledge required by technology practitioners; the second week focused on contemporary applications. Student evaluations and feedback from student advisors indicates that the summer school achieved its objectives of 1) exposing students to the range of nuclear security applications for which radiation detection is necessary, 2) articulating the relevance of student research into the broader context, and 3) exciting students about the possibility of future careers in nuclear security.

Problems on shipping high-enriched nuclear materials

International Nuclear Information System (INIS)

Ganzha, V.V.; Demko, N.A.; Deryavko, I.I.; Zelenski, D.I.; Kolbaenkov, A.N.; Pivovarov, O.S.; Storozhenko, A.N.; Chernyad'ev, V.V.; Yakovlev, V.V.; Gorin, N.V.; Prokhod'ko, A.I.; Sherbina, A.N.; Barsanov, V.I.; Dyakov, E.K.; Tishenko, M.F.; Khlystov, A.I.; Vasil'ev, A.P.; Smetannikov, V.P.

1998-01-01

In 1996-1998 all Russian nuclear materials were taken out of the Institute of Atomic Energy of Kazakhstan National Nuclear Centre (IAE NNC RK). In this report there are basic tasks related to the performance of this work. They are: 1) Preparation of Russian nuclear materials (NM) kept at IAE NNC RK for transportation; 2) accounting and control of Russian nuclear materials kept at IAE NNC RK; 3) arrangement of permit papers for NM transportation; 4) NM transportation from IAE NNC RK to the enterprises of Russian MINATOM; 5) provision of nuclear and radiation safety in the course of operations with NM; 6) provision of physical protection for Russian NM

[Measures against Radiation Exposure Due to Large-Scale Nuclear Accident in Distant Place--Radioactive Materials in Nagasaki from Fukushima Daiichi Nuclear Power Plant].

Science.gov (United States)

Yuan, Jun; Sera, Koichiro; Takatsuji, Toshihiro

2015-01-01

To investigate human health effects of radiation exposure due to possible future nuclear accidents in distant places and other various findings of analysis of the radioactive materials contaminating the atmosphere of Nagasaki due to the Fukushima Daiichi Nuclear Power Plant accident. The concentrations of radioactive materials in aerosols in the atmosphere of Nagasaki were measured using a germanium semiconductor detector from March 2011 to March 2013. Internal exposure dose was calculated in accordance with ICRP Publ. 72. Air trajectories were analyzed using NOAA and METEX web-based systems. (134)Cs and (137)Cs were repeatedly detected. The air trajectory analysis showed that (134)Cs and (137)Cs flew directly from the Fukushima Daiichi Nuclear Power Plant from March to April 2011. However, the direct air trajectories were rarely detected after this period even when (134)Cs and (137)Cs were detected after this period. The activity ratios ((134)Cs/(137)Cs) of almost all the samples converted to those in March 2011 were about unity. This strongly suggests that the (134)Cs and (137)Cs detected mainly originated from the Fukushima Daiichi Nuclear Power Plant accident in March 2011. Although the (134)Cs and (137)Cs concentrations per air volume were very low and the human health effects of internal exposure via inhalation is expected to be negligible, the specific activities (concentrations per aerosol mass) were relatively high. It was found that possible future nuclear accidents may cause severe radioactive contaminations, which may require radiation exposure control of farm goods to more than 1000 km from places of nuclear accidents.

Study of nuclear environment and material strategy

International Nuclear Information System (INIS)

Kamei, Takashi

2011-01-01

There is a concern about the environmental hazard caused by radioactive materials coming with the expansion of nuclear power and even by renewable energies, which are used as countermeasures against global warming to construct a sustainable society. A concept to internalize the pollution caused by radioactive materials, which are directly or indirectly related to nuclear power, to economical activities by adopting externality is proposed. Energy and industrial productions are strongly related to the supply of material. Therefore material flow is also part of this internalization concept. The concept is named 'NEMS (Nuclear Environment and Material Strategy)'. Fission products and transuranic isotopes from nuclear power such as plutonium are considered in this concept. Thorium, which comes from the material flow of rare-earth production to support the elaboration of renewable energies including electric vehicles on the consumer side, is considered as an externality of the non-nuclear power field. Fission products contain some rare-earth materials. Thus, these rare-earth materials, which are extracted by the advanced ORIENT (Optimization by Recycling Instructive Elements) cycle, are internalized as rare-earth supplier in economy. However, the supply quantity is limited. Therefore rare-earth production itself is still needed. The externality of rare-earth production is thorium and is internalized by using it as nuclear fuel. In this case, the demand of thorium is still small within these few decades compared to the production of thorium as byproduct of the rare-earth production. A thorium energy bank (The Bank) is advanced to regulate the storage of the excess amount of thorium inside of an international framework in order to prevent environmental hazard resulting from the illegal disposal of thorium. In this paper, the material flows of thorium and rare-earth are outlined. Their material balance are demonstrated based on the prediction of rare-earth mining and an

Passive nondestructive assay of nuclear materials

International Nuclear Information System (INIS)

Reilly, D.; Ensslin, N.; Smith, H. Jr.; Kreiner, S.

1991-03-01

The term nondestructive assay (NDA) is applied to a series of measurement techniques for nuclear fuel materials. The techniques measure radiation induced or emitted spontaneously from the nuclear material; the measurements are nondestructive in that they do not alter the physical or chemical state of the nuclear material. NDA techniques are characterized as passive or active depending on whether they measure radiation from the spontaneous decay of the nuclear material or radiation induced by an external source. This book emphasizes passive NDA techniques, although certain active techniques like gamma-ray absorption densitometry and x-ray fluorescence are discussed here because of their intimate relation to passive assay techniques. The principal NDA techniques are classified as gamma-ray assay, neutron assay, and calorimetry. Gamma-ray assay techniques are treated in Chapters 1--10. Neutron assay techniques are the subject of Chapters 11--17. Chapters 11--13 cover the origin of neutrons, neutron interactions, and neutron detectors. Chapters 14--17 cover the theory and applications of total and coincidence neutron counting. Chapter 18 deals with the assay of irradiated nuclear fuel, which uses both gamma-ray and neutron assay techniques. Chapter 19 covers perimeter monitoring, which uses gamma-ray and neutron detectors of high sensitivity to check that no unauthorized nuclear material crosses a facility boundary. The subject of Chapter 20 is attribute and semiquantitative measurements. The goal of these measurements is a rapid verification of the contents of nuclear material containers to assist physical inventory verifications. Waste and holdup measurements are also treated in this chapter. Chapters 21 and 22 cover calorimetry theory and application, and Chapter 23 is a brief application guide to illustrate which techniques can be used to solve certain measurement problems

National architectures for the detection of nuclear and radioactive materials at port facilities

International Nuclear Information System (INIS)

Ortiz, A.

2009-01-01

The basic objective of the national architectures is to protect people and the environment against a possible misuse of nuclear and radioactive materials. This issue has become even more important in recent years because maritime transport currently amounts to 80% of world trade, growing from 83 million shipments in 1990 to 334 million in 2005. (Author)

IBA studies of helium mobility in nuclear materials revisited

Energy Technology Data Exchange (ETDEWEB)

Trocellier, P., E-mail: patrick.trocellier@cea.fr [CEA, DEN, Service de Recherches de Métallurgie Physique, Laboratoire JANNUS, F-91191 Gif-sur-Yvette (France); Agarwal, S.; Miro, S. [CEA, DEN, Service de Recherches de Métallurgie Physique, Laboratoire JANNUS, F-91191 Gif-sur-Yvette (France); Vaubaillon, S. [CEA, DEN, Service de Recherches de Métallurgie Physique, Laboratoire JANNUS, F-91191 Gif-sur-Yvette (France); CEA, INSTN, UEPTN, F-91191 Gif-sur-Yvette (France); Leprêtre, F.; Serruys, Y. [CEA, DEN, Service de Recherches de Métallurgie Physique, Laboratoire JANNUS, F-91191 Gif-sur-Yvette (France)

2015-12-15

The aim of this paper is to point out and to discuss some features extracted from the study of helium migration in nuclear materials performed during the last fifteen years using ion beam analysis (IBA) measurements. The first part of this paper is devoted to a brief description of the two main IBA methods used, i.e. deuteron induced nuclear reaction for {sup 3}He depth profiling and high-energy heavy-ion induced elastic recoil detection analysis for {sup 4}He measurement. In the second part, we provide an overview of the different studies carried out on model nuclear waste matrices and model nuclear reactor structure materials in order to illustrate and discuss specific results in terms of key influence parameters in relation with thermal or radiation activated migration of helium. Finally, we show that among the key parameters we have investigated as able to influence the height of the helium migration barrier, the following can be considered as pertinent: the experimental conditions used to introduce helium (implanted ion energy and implantation fluence), the grain size of the matrix, the lattice cell volume, the Young's modulus, the ionicity degree of the chemical bond between the transition metal atom M and the non-metal atom X, and the width of the band gap.

Isotopic Determination of Nuclear Materials Using Nuclear Fission Track Registration Technique and Thermal Ionization Mass Spectrometric Technique

International Nuclear Information System (INIS)

Jeon, Young Sin; Pyo, Hyeong Yeol; Park, Yong Joon; Song, Kyu Seok; Kim, Won Ho; Jee, Kwang Yong

2007-05-01

It is very important to develope the technology for the determination of isotopic ratios of hot particles( 234 U, 235 U, 236 U etc.) detected from swipe samples of various nuclear facilities. This technology is highly competitive internationally and has to be established independently as long as our government maintains atomic energy and treats nuclear materials. In this text, sample pretreatment procedure, gamma-ray counting, alpha or fission track techniques, isotopic analysis of U and Pu, background problems and detection limits for mass determination, and their application to the real swipe sample were described with detailed procedure. This technology would contribute to the Korean economy's high growth rate as well as to superiority of government's leading research and development programs if successfully established

Concepts of IAEA nuclear materials accounting

International Nuclear Information System (INIS)

Oakberg, John A.

2001-01-01

The paper describes nuclear material accounting from the standpoint of IAEA Safeguards and how this accounting is applied by the Agency. The basic concepts of nuclear material accounting are defined and the way these apply to States with INFCIRC/153-type safeguards agreements is presented. (author)

Nuclear Fuel Cycle & Vulnerabilities

Energy Technology Data Exchange (ETDEWEB)

Boyer, Brian D. [Los Alamos National Laboratory

2012-06-18

The objective of safeguards is the timely detection of diversion of significant quantities of nuclear material from peaceful nuclear activities to the manufacture of nuclear weapons or of other nuclear explosive devices or for purposes unknown, and deterrence of such diversion by the risk of early detection. The safeguards system should be designed to provide credible assurances that there has been no diversion of declared nuclear material and no undeclared nuclear material and activities.

Nuclear Security Recommendations on Physical Protection of Nuclear Material and Nuclear Facilities (INFCIRC/225/Revision 5): Recommendations

International Nuclear Information System (INIS)

2011-01-01

This publication, Revision 5 of Physical Protection of Nuclear Material and Nuclear Facilities (INFCIRC/225), is intended to provide guidance to States and their competent authorities on how to develop or enhance, implement and maintain a physical protection regime for nuclear material and nuclear facilities, through the establishment or improvement of their capabilities to implement legislative and regulatory programmes. The recommendations presented in this publication reflect a broad consensus among IAEA Member States on the requirements which should be met for the physical protection of nuclear materials and nuclear facilities.

Detecting errors and anomalies in computerized materials control and accountability databases

International Nuclear Information System (INIS)

Whiteson, R.; Hench, K.; Yarbro, T.; Baumgart, C.

1998-01-01

The Automated MC and A Database Assessment project is aimed at improving anomaly and error detection in materials control and accountability (MC and A) databases and increasing confidence in the data that they contain. Anomalous data resulting in poor categorization of nuclear material inventories greatly reduces the value of the database information to users. Therefore it is essential that MC and A data be assessed periodically for anomalies or errors. Anomaly detection can identify errors in databases and thus provide assurance of the integrity of data. An expert system has been developed at Los Alamos National Laboratory that examines these large databases for anomalous or erroneous data. For several years, MC and A subject matter experts at Los Alamos have been using this automated system to examine the large amounts of accountability data that the Los Alamos Plutonium Facility generates. These data are collected and managed by the Material Accountability and Safeguards System, a near-real-time computerized nuclear material accountability and safeguards system. This year they have expanded the user base, customizing the anomaly detector for the varying requirements of different groups of users. This paper describes the progress in customizing the expert systems to the needs of the users of the data and reports on their results

Summary Report for the Radiation Detection for Nuclear Security Summer School 2014

Energy Technology Data Exchange (ETDEWEB)

Runkle, Robert C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Baciak, James E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Woodring, Mitchell L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jenno, Diana M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-09-01

Executive Summary The Pacific Northwest National Laboratory (PNNL) hosted students from across the United States at the 3rd Radiation Detection for Nuclear Security Summer School from 16 – 27 June 2014. The summer school provided students with a unique understanding of nuclear security challenges faced in the field and exposed them to the technical foundations, analyses, and insight that will be required by future leaders in technology development and implementation. The course heavily emphasized laboratory and field demonstrations including direct measurements of special nuclear material. Student evaluations and feedback from student advisors indicates that the summer school achieved its objectives of 1) exposing students to the range of nuclear security applications for which radiation detection is necessary, 2) articulating the relevance of student research into the broader context, and 3) exciting students about the possibility of future careers in nuclear security. In fact, we are beginning to see previous students both enroll in graduate programs (former undergraduates) and complete internships at agencies like the National Nuclear Security Administration.

The Nuclear Car Wash: Neutron interrogation of cargo containers to detect hidden SNM

Science.gov (United States)

Hall, J. M.; Asztalos, S.; Biltoft, P.; Church, J.; Descalle, M.-A.; Luu, T.; Manatt, D.; Mauger, G.; Norman, E.; Petersen, D.; Pruet, J.; Prussin, S.; Slaughter, D.

2007-08-01

LLNL is actively involved in the development of advanced technologies for use in detecting threats in sea-going cargo containers, particularly the presence of hidden special nuclear materials (SNM). The "Nuclear Car Wash" (NCW) project presented here uses a high-energy (En ≈ 3.5-7.0 MeV) neutron probe to scan a container and then takes high-energy (Eγ ⩾ 2.5 MeV), β-delayed γ-rays emitted during the subsequent decay of any short-lived, neutron-induced fission products as a signature of fissionable material. The components of the proposed system (e.g. neutron source, gamma detectors, etc.) will be discussed along with data processing schemes, possible threat detection metrics and potential interference signals. Results from recent laboratory experiments using a prototype system at LLNL will also be presented.

The Nuclear Car Wash: Neutron interrogation of cargo containers to detect hidden SNM

International Nuclear Information System (INIS)

Hall, J.M.; Asztalos, S.; Biltoft, P.; Church, J.; Descalle, M.-A.; Luu, T.; Manatt, D.; Mauger, G.; Norman, E.; Petersen, D.; Pruet, J.; Prussin, S.; Slaughter, D.

2007-01-01

LLNL is actively involved in the development of advanced technologies for use in detecting threats in sea-going cargo containers, particularly the presence of hidden special nuclear materials (SNM). The 'Nuclear Car Wash' (NCW) project presented here uses a high-energy (E n ∼ 3.5-7.0 MeV) neutron probe to scan a container and then takes high-energy (E γ ≥ 2.5 MeV), β-delayed γ-rays emitted during the subsequent decay of any short-lived, neutron-induced fission products as a signature of fissionable material. The components of the proposed system (e.g. neutron source, gamma detectors, etc.) will be discussed along with data processing schemes, possible threat detection metrics and potential interference signals. Results from recent laboratory experiments using a prototype system at LLNL will also be presented

Nuclear Materials Management for the Nevada Test Site (NTS)

International Nuclear Information System (INIS)

Jesse C. Schreiber

2007-01-01

The Nevada Test Site (NTS) has transitioned from its historical role of weapons testing to a broader role that is focused on being a solution to multiple National Nuclear Security Administration (NNSA) challenges and opportunities with nuclear materials for the nation. NTS is supporting other NNSA sites challenged with safe nuclear materials storage and disposition. NNSA, with site involvement, is currently transforming the nuclear stockpile and supporting infrastructure to meet the 2030 vision. Efforts are under way to make the production complex smaller, more consolidated, and more modern. With respect to the nuclear material stockpile, the NNSA sites are currently reducing the complex nuclear material inventory through dispositioning and consolidating nuclear material. This includes moving material from other sites to NTS. State-of-the-art nuclear material management and control practices at NTS are essential for NTS to ensure that these new activities are accomplished in a safe, secure, efficient, and environmentally responsible manner. NTS is aggressively addressing this challenge

Management of Global Nuclear Materials for International Security

International Nuclear Information System (INIS)

Isaacs, T; Choi, J-S

2003-01-01

Nuclear materials were first used to end the World War II. They were produced and maintained during the cold war for global security reasons. In the succeeding 50 years since the Atoms for Peace Initiative, nuclear materials were produced and used in global civilian reactors and fuel cycles intended for peaceful purposes. The Nonproliferation Treaty (NPT) of 1970 established a framework for appropriate applications of both defense and civilian nuclear activities by nuclear weapons states and non-nuclear weapons states. As global inventories of nuclear materials continue to grow, in a diverse and dynamically changing manner, it is time to evaluate current and future trends and needed actions: what are the current circumstances, what has been done to date, what has worked and what hasn't? The aim is to identify mutually reinforcing programmatic directions, leading to global partnerships that measurably enhance international security. Essential elements are material protection, control and accountability (MPC and A) of separated nuclear materials, interim storage, and geologic repositories for all nuclear materials destined for final disposal. Cooperation among key partners, such as the MPC and A program between the U.S. and Russia for nuclear materials from dismantled weapons, is necessary for interim storage and final disposal of nuclear materials. Such cooperative partnerships can lead to a new nuclear regime where a complete fuel cycle service with fuel leasing and spent fuel take-back can be offered to reactor users. The service can effectively minimize or even eliminate the incentive or rationale for the user-countries to develop their indigenous enrichment and reprocessing technologies. International cooperation, supported by governments of key countries can be best to facilitate the forum for formation of such cooperative partnerships

Measures to prevent, intercept and respond to illicit uses of nuclear material and radioactive sources. Proceedings

International Nuclear Information System (INIS)

2002-01-01

As nuclear programmes have evolved, the quantities of nuclear material in use or storage, and the number of facilities operating or shut down has increased. In particular, the dismantling of nuclear weapons has resulted in greatly increased stockpiles of weapons usable plutonium and highly enriched uranium. Concern over the security of these and related materials has been further raised by the continued occurrence of cases of illicit trafficking. The risks are theft, leading to trafficking and possible illicit use, and sabotage which could lead to the creation of radiological hazards. The challenge is threefold: prevention, detection and interception, and response. Prevention starts with effective national systems for accountancy, control and protection. Detection and interception involves effective measures to combat illicit trafficking, and response requires planning for the consequences of theft and sabotage. Responsibilities in these fields are national, but nuclear security also has a powerful international dimension. The consequences of failures in national measures reach beyond national boundaries. The effectiveness of national nuclear security can be enhanced through international measures: through agreed international norms, standards and guides, through training and advice, through information exchange and the sharing of experience, and through developing common understandings and perceptions. The Stockholm Conference contributed by focusing on the threats, including terrorist, to nuclear and other radioactive materials; on how to assess them and on how to develop the appropriate security measures. National measures to protect nuclear material and facilities and the continuing development of international standards and obligations were described. The conference discussed the patterns and trends in the illicit trafficking of nuclear and other radioactive materials and national and international measures to combat such trafficking. Finally, it considered

Measures to prevent, intercept and respond to illicit uses of nuclear material and radioactive sources. Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-08-01

As nuclear programmes have evolved, the quantities of nuclear material in use or storage, and the number of facilities operating or shut down has increased. In particular, the dismantling of nuclear weapons has resulted in greatly increased stockpiles of weapons usable plutonium and highly enriched uranium. Concern over the security of these and related materials has been further raised by the continued occurrence of cases of illicit trafficking. The risks are theft, leading to trafficking and possible illicit use, and sabotage which could lead to the creation of radiological hazards. The challenge is threefold: prevention, detection and interception, and response. Prevention starts with effective national systems for accountancy, control and protection. Detection and interception involves effective measures to combat illicit trafficking, and response requires planning for the consequences of theft and sabotage. Responsibilities in these fields are national, but nuclear security also has a powerful international dimension. The consequences of failures in national measures reach beyond national boundaries. The effectiveness of national nuclear security can be enhanced through international measures: through agreed international norms, standards and guides, through training and advice, through information exchange and the sharing of experience, and through developing common understandings and perceptions. The Stockholm Conference contributed by focusing on the threats, including terrorist, to nuclear and other radioactive materials; on how to assess them and on how to develop the appropriate security measures. National measures to protect nuclear material and facilities and the continuing development of international standards and obligations were described. The conference discussed the patterns and trends in the illicit trafficking of nuclear and other radioactive materials and national and international measures to combat such trafficking. Finally, it considered

U.S. national nuclear material control and accounting system

International Nuclear Information System (INIS)

Taylor, S; Terentiev, V G

1998-01-01

Issues related to nuclear material control and accounting and illegal dealing in these materials were discussed at the April 19--20, 1996 Moscow summit meeting (G7 + Russia). The declaration from this meeting reaffirmed that governments are responsible for the safety of all nuclear materials in their possession and for the effectiveness of the national control and accounting system for these materials. The Russian delegation at this meeting stated that ''the creation of a nuclear materials accounting, control, and physical protection system has become a government priority''. Therefore, in order to create a government nuclear material control and accounting system for the Russian Federation, it is critical to study the structure, operating principles, and regulations supporting the control and accounting of nuclear materials in the national systems of nuclear powers. In particular, Russian specialists have a definite interest in learning about the National Nuclear Material Control and Accounting System of the US, which has been operating successfully as an automated system since 1968

Management review of nuclear material control and accounting systems

International Nuclear Information System (INIS)

1975-06-01

Section 70.58, ''Fundamental Nuclear Material Controls,'' of 10 CFR Part 70, ''Special Nuclear Materials,'' requires, in paragraph 70.58(c), that certain licensees authorized to possess more than one effective kilogram of special nuclear material establish a management system to provide for the development, revision, implementation, and enforcement of nuclear material control and accounting procedures. Such a system must provide for a review of the nuclear material control system at least every 12 months. This guide describes the purpose and scope, personnel qualifications, depth of detail, and procedures that are acceptable to the NRC staff for the management review of nuclear material control systems required under paragraph 70.58(c) of 10 CFR Part 70. (U.S.)

Base isolation for nuclear power and nuclear material facilities

International Nuclear Information System (INIS)

Eidinger, J.M.; Kircher, C.A.; Vaidya, N.; Constantinou, M.; Kelly, J.M.; Seidensticker, R.; Tajirian, F.F.; Ovadia, D.

1989-01-01

This report serves to document the status of the practice for the use of base isolation systems in the design and construction of nuclear power and nuclear material facilities. The report first describes past and current (1989) applications of base isolation in nuclear facilities. The report then provides a brief discussion of non-nuclear applications. Finally, the report summarizes the status of known base-isolation codes and standards

Human as a component of a nuclear material safeguard system

International Nuclear Information System (INIS)

Morgan, D.E.; Schechter, R.S.

1978-01-01

Many human vigilance experiments are summarized and principles are extracted which should be useful in designing and evaluating a nuclear material safeguard system. A human is a poor observer and is not a dependable part of any man-machine system when required to function as an observer. There are a few techniques which improve his performance by providing feedback. A conceptual model is presented which is helpful in design and evaluation of systems. There is some slight experimental support for the model. Finally, some techniques of time study and statistical control charting will be useful as a means of detecting nuclear diversion attempts

Order for execution of the law concerning regulation of nuclear source materials, nuclear fuel materials and reactors

International Nuclear Information System (INIS)

1977-01-01

The designations according to Item 1, Article 3 and Item 1, Article 13 of the Law must be obtained for each factory or business place where refining and fabrication of nuclear material are to be performed. One who wants to obtain such designation should file an application attached with a business plan and other documents via the director of a regional bureau of international trade and industry having jurisdiction over such factory or business place. When nuclear material refiners and nuclear material fabricators wish to obtain the approval for change stipulated in Item 1, Article 6 and Item 1, Article 16 of the Law, they must file applications to the Prime Minister and the Minister of International Trade and Industry via said directors. Chief handlers of nuclear fuel materials shall be approved among those meeting the strict requirements. One who wishes to install reactors must obtain the approval for each factory or business place where the reactors are to be installed. The permission must be obtained for each nuclear ship entering Japanese waters. The reactors proper and several facilities are subject to periodic inspection. (Rikitake, Y.)

Nuclear physics methods in materials research

International Nuclear Information System (INIS)

Bethge, K.; Baumann, H.; Jex, H.; Rauch, F.

1980-01-01

Proceedings of the seventh divisional conference of the Nuclear Physics Division held at Darmstadt, Germany, from 23rd through 26th of September, 1980. The scope of this conference was defined as follows: i) to inform solid state physicists and materials scientists about the application of nuclear physics methods; ii) to show to nuclear physicists open questions and problems in solid state physics and materials science to which their methods can be applied. According to the intentions of the conference, the various nuclear physics methods utilized in solid state physics and materials science and especially new developments were reviewed by invited speakers. Detailed aspects of the methods and typical examples extending over a wide range of applications were presented as contributions in poster sessions. The Proceedings contain all the invited papers and about 90% of the contributed papers. (orig./RW)

Development of technologies for national control of and accountancy for nuclear materials

International Nuclear Information System (INIS)

Choi, Young Myung; Kwack, E. H.; Kim, B. K.

2002-03-01

The aim of this project is to establish a rigid foundation of national safeguards and to develop the new technologies for the nuclear control. This project is composed of four different technologies; 1. Monitoring technology for nuclear materials, 2. Detection technology for a single particle, 3. Safeguards information management technology, 4. Physical protection technology. Various studies such as a remote verification system for CANDU spent fuel in dry storage canister, a spent fuel verification system using an optical fiber scintillator, and development of softwares for safeguards and physical protection were performed in the frist phase('99-'01). As a result of this research, it has been identified that the developed technologies could be a crucial means of the control for the nuclear material and facilities related. We are planing to accomplish a steady national safeguard system in the second phase('02-'06). This research will help to elevate the transparency and credibility in national nuclear activities by improving the relative technologies

Gamma spectrometric discrimination of special nuclear materials

International Nuclear Information System (INIS)

Dowdall, M.; Mattila, A.; Ramebaeck, H.; Aage, H.K.; Palsson, S.E.

2012-12-01

This report presents details pertaining to an exercise conducted as part of the NKS-B programme using synthetic gamma ray spectra to simulate the type of data that may be encountered in the interception of material potentially containing special nuclear materials. A range of scenarios were developed involving sources that may or may not contain special nuclear materials. Gamma spectral data was provided to participants as well as ancillary data and participants were asked, under time constraint, to determine whether or not the data was indicative of circumstances involving special nuclear materials. The situations varied such that different approaches were required in order to obtain the correct result in each context. In the majority of cases participants were able to correctly ascertain whether or not the situations involved special nuclear material. Although fulfilling the primary goal of the exercise, some participants were not in a position to correctly identify with certainty the material involved, Situations in which the smuggled material was being masked by another source proved to be the most challenging for participants. (Author)

Gamma spectrometric discrimination of special nuclear materials

Energy Technology Data Exchange (ETDEWEB)

Dowdall, M. [Norwegian Radiation Protection Authority (Norway); Mattila, A. [Radiation and Nuclear Safety Authority, Helsinki (Finland); Ramebaeck, H. [Swedish Defence Research Agency, Stockholm (Sweden); Aage, H.K. [Danish Emergency Management Agency, Birkeroed (Denmark); Palsson, S.E. [Icelandic Radiation Safety Authority, Reykjavik (Iceland)

2012-12-15

This report presents details pertaining to an exercise conducted as part of the NKS-B programme using synthetic gamma ray spectra to simulate the type of data that may be encountered in the interception of material potentially containing special nuclear materials. A range of scenarios were developed involving sources that may or may not contain special nuclear materials. Gamma spectral data was provided to participants as well as ancillary data and participants were asked, under time constraint, to determine whether or not the data was indicative of circumstances involving special nuclear materials. The situations varied such that different approaches were required in order to obtain the correct result in each context. In the majority of cases participants were able to correctly ascertain whether or not the situations involved special nuclear material. Although fulfilling the primary goal of the exercise, some participants were not in a position to correctly identify with certainty the material involved, Situations in which the smuggled material was being masked by another source proved to be the most challenging for participants. (Author)

Materials for nuclear reactors

International Nuclear Information System (INIS)

Banerjee, S.; Kamath, H.S.

2005-01-01

The improved performance of present generation nuclear reactors and the realization of advanced reactor concepts, both, require development of better materials. Physical metallurgy/materials science principles which have been exploited in meeting the exacting requirements of nuclear reactor materials (fuels and structural materials), are outlined citing a few specific examples. While the incentive for improvement of traditional fuels (e.g., UO 2 fuel) is primarily for increasing the average core burn up, the development of advanced fuels (e.g., MOX, mixed carbide, nitride, silicide and dispersion fuels) are directed towards better utilization of fissile and fertile inventories through adaptation of innovative fuel cycles. As the burn up of UO 2 fuel reaches higher levels, a more detailed and quantitative understanding of the phenomena such as fission gas release, fuel restructuring induced by radiation and thermal gradients and pellet-clad interaction is being achieved. Development of zirconium based alloys for both cladding and pressure tube applications is discussed with reference to their physical metallurgy, fabrication techniques and in-reactor degradation mechanisms. The issue of radiation embrittlement of reactor pressure vessels (RPVs) is covered drawing a comparison between the western and eastern specifications of RPV steels. The search for new materials which can stand higher rates of atomic displacement due to radiation has led to the development of swelling resistant austenitic and ferritic stainless steels for fast reactor applications as exemplified by the development of the D-9 steel for Indian fast breeder reactor. The presentation will conclude by listing various materials related phenomena, which have a strong bearing on the successful development of future nuclear energy systems. (author)

The law for the regulations of nuclear source materials, nuclear fuel materials and reactors

International Nuclear Information System (INIS)

1979-01-01

The law aims to perform regulations on enterprises of refining, processing and reprocessing of nuclear source and fuel materials and on establishment and operation of reactors to realize the peaceful and deliberate utilization of atomic energy according to the principle of the atomic energy basic law. Regulations of use of internationally regulated substances are also envisaged to observe international agreements. Basic concepts and terms are defined, such as: atomic energy; nuclear fuel material; nuclear source material; reactor; refining; processing; reprocessing and internationally regulated substance. Any person besides the Power Reactor and Nuclear Fuel Material Developing Corporation who undertakes refining shall be designated by the Prime Minister and the Minister of International Trade and Industry. An application shall be filed to the ministers concerned, listing name and address of the person, name and location of the refining works, equipment and method of refining, etc. The permission of the Prime Minister is necessary for any person who engages in processing. An application shall be filed to the Prime Minister, listing name and address of the person, name and location of the processing works and equipment and method of processing, etc. Permission of the Prime Minister, the Minister of International Trade and Industry or the Minister of Transport is necessary for any person who sets up reactors. An application shall be filed to the minister concerned, listing name and address of the person, purpose of operation, style, thermal output of reactor and number of units, etc. (Okada, K.)

Automated processing of nuclear materials accounting data

International Nuclear Information System (INIS)

Straka, J.; Pacak, P.; Moravec, J.

1980-01-01

An automated system was developed of nuclear materials accounting in Czechoslovakia. The system allows automating data processing including data storage. It comprises keeping records of inventories and material balance. In designing the system, the aim of the IAEA was taken into consideration, ie., building a unified information system interconnected with state-run systems of accounting and checking nuclear materials in the signatory countries of the non-proliferation treaty. The nuclear materials accounting programs were written in PL-1 and were tested at an EC 1040 computer at UJV Rez where also the routine data processing takes place. (B.S.)

1993 Annual report of the Brazilian-Argentine Agency for Accounting and Control of Nuclear Materials - ABACC

International Nuclear Information System (INIS)

1994-01-01

The 1993 annual report of the Brazilian Argentine Agency for Accounting and Control of Nuclear Materials, (ABACC), describes the activities regarding the administration and application of the Control and Accounting Common System (SCCC) established by the bilateral agreement between the Republic of Argentine and Federative Republic of Brazil for exclusive peaceful use of the nuclear energy. The main goal to verify practically all the installations which were not subjected to the international safeguards, before the agreement, was reached. Considering the safeguards application under implementation in both countries, the ABACC is preparing itself technically for the quadripartite agreement to be into force and signed among Argentine, Brazil, IAEA and ABACC. On checking the procedures established by the SCCC and controlled material, nothing was detected that could indicate nuclear material diversion either for nuclear weapon or for other explosive nuclear device. (B.C.A.)

Vulnerability Analysis Considerations for the Transportation of Special Nuclear Material

International Nuclear Information System (INIS)

Nicholson, Lary G.; Purvis, James W.

1999-01-01

The vulnerability analysis methodology developed for fixed nuclear material sites has proven to be extremely effective in assessing associated transportation issues. The basic methods and techniques used are directly applicable to conducting a transportation vulnerability analysis. The purpose of this paper is to illustrate that the same physical protection elements (detection, delay, and response) are present, although the response force plays a dominant role in preventing the theft or sabotage of material. Transportation systems are continuously exposed to the general public whereas the fixed site location by its very nature restricts general public access

78 FR 38739 - Special Nuclear Material Control and Accounting Systems for Nuclear Power Plants

Science.gov (United States)

2013-06-27

... Systems for Nuclear Power Plants AGENCY: Nuclear Regulatory Commission. ACTION: Regulatory guide; issuance... Guide (RG) 5.29, ``Special Nuclear Material Control and Accounting Systems for Nuclear Power Plants... material control and accounting. This guide applies to all nuclear power plants. ADDRESSES: Please refer to...

Structural materials for innovative nuclear systems (SMINS)

International Nuclear Information System (INIS)

2008-01-01

Structural materials research is a field of growing relevance in the nuclear sector, especially for the different innovative reactor systems being developed within the Generation IV International Forum (GIF), for critical and subcritical transmutation systems, and of interest to the Global Nuclear Energy Partnership (GNEP). Under the auspices of the NEA Nuclear Science Committee (NSC) the Workshop on Structural Materials for Innovative Nuclear Systems (SMINS) was organised in collaboration with the Forschungszentrum Karlsruhe in Germany. The objectives of the workshop were to exchange information on structural materials research issues and to discuss ongoing programmes, both experimental and in the field of advanced modelling. These proceedings include the papers and the poster session materials presented at the workshop, representing the international state of the art in this domain. (author)

Nuclear technology and materials science

International Nuclear Information System (INIS)

Olander, D.R.

1992-01-01

Current and expected problems in the materials of nuclear technology are reviewed. In the fuel elements of LWRs, cladding waterside corrosion, secondary hydriding and pellet-cladding interaction may be significant impediments to extended burnup. In the fuel, fission gas release remains a key issue. Materials issues in the structural alloys of the primary system include stress-corrosion cracking of steel, corrosion of steam generator tubing and pressurized thermal shock of the reactor vessel. Prediction of core behavior in severe accidents requires basic data and models for fuel liquefaction, aerosol formation, fission product transport and core-concrete interaction. Materials questions in nuclear waste management and fusion technology are briefly reviewed. (author)

Decision-based model development for nuclear material theft, smuggling, and illicit use

International Nuclear Information System (INIS)

Scott, B.

2002-01-01

Full text: Nuclear material is vulnerable to a range of theft, sabotage, smuggling and illicit use scenarios. These scenarios are dependent on the choices of individuals and organizations involved in these activities. These choices, in turn; are dependent on the perceived payoff vectors of the involved players. These payoff vectors can include monetary gain, ability to avoid detection, penalties for detection, difficulty of accomplishment, resource constraints, infrastructure support, etc. Threat scenarios can be developed from these individual choices, and the set of worst-case threat scenarios can be compiled into a threat definition. The implementation of physical protection controls is dependent on the developed threat scenarios. The analysis of the composition of the postulated threat can be based on the analysis of the postulated decisions of the individuals and organizations involved on theft, smuggling, and illicit use. This paper proposes a model to systematically analyze the significant decision points that an individual or organization addresses as result of its goals. The model's dependence on assumptions is discussed. Using these assumptions, a model is developed that assigns probabilities to a set of decisions performed by the individuals involved in theft/smuggling. The individual and organisation's decisions are based on the perceived cost/benefit of the decisions and the resource constraints. Methods for functionally obtaining decision probabilities from perceived cost/benefit are proposed. The treatment of high-consequence/low-probability events is discussed in terms of analysis of precursor events, and the use of sensitivity analysis is discussed. An example of a simplified model for nuclear material theft, smuggling, and illicit use is presented, and the results of this simplified model are evaluated. By attempting to model the potential distribution of nuclear material theft/smuggling events, this model increases the analytical tools available

Safeguards and nuclear forensics

International Nuclear Information System (INIS)

Gangotra, Suresh

2016-01-01

Nuclear Safeguards is the detection of diversion of significant quantities of nuclear material from peaceful nuclear activities to the manufacture of nuclear weapons, or of other nuclear explosive devices or for purposes unknown, and deterrence of such diversion by early detection. Safeguards implementation involves nuclear material accounting and containment and surveillance measures. The safeguards are implemented in nuclear facilities by the states, or agencies and International Atomic Energy Agency (IAEA). The measures for the safeguards include nuclear material Accounting (NUMAC) and Containment and surveillance systems. In recent times, there have been advances in safeguards like Near Real Time Monitoring (NRTM), Dynamic Nuclear Material Accounting (DNMA), Safeguards-by-Design (SBD), satellite imagery, information from open sources, remote monitoring etc

Proceedings of the national workshop on nuclear forensics: fundamentals and applications - course material

International Nuclear Information System (INIS)

Mishra, S.; Chaudhury, Probal

2016-01-01

This course introduces the understanding of the nuclear/radioactive material involved either in illicit trafficking or possibility of getting involved in nuclear or radiological threats or incidents. It will also highlight the basics of nuclear forensics involving various steps i.e categorization, characterization, interpretation and finally the reconstruction of the nuclear/radiological scenario. This will also provide a platform for discussing the challenges and opportunities associated with such investigations. Various techniques adopted throughout the globe for the characterization of nuclear/radioactive materials for nuclear/radiological forensic investigations involving destructive, non-destructive assay methodologies along with traditional forensic analysis will be discussed. The international cooperation which is an indispensable part for nuclear forensic investigation and nuclear forensics support at IAEA will also be discussed in the forum. Apart from this the applications of the techniques in safeguards and other frameworks will also be a part of this workshop. For understanding of the participants about the subject, a table top exercise will be conducted along with demonstration of different radiation detection systems. This manual will serve as a post course reference. Papers relevant to INIS are indexed separately

Chemical characterization of materials relevant to nuclear technology using neutron and proton based nuclear analytical methods

International Nuclear Information System (INIS)

Acharya, R.

2014-01-01

Nuclear analytical techniques (NATs), utilizing neutron and proton based nuclear reactions and subsequent measurement of gamma rays, are capable of chemical characterization of various materials at major to trace concentration levels. The present article deals with the recent developments and applications of conventional and k0-based internal monostandard (i) neutron activation analysis (NAA) and (ii) prompt gamma ray NAA (PGNAA) methods as well as (iii) in situ current normalized particle induced gamma ray emission (PIGE). The materials that have been analyzed by NAA and PGNAA include (i) nuclear reactor structural materials like zircaloys, stainless steels, Ni alloys, high purity aluminium and graphite and (ii) uranium oxide, U-Th mixed oxides, uranium ores and minerals. Internal monostandard NAA (IM-NAA) method with in situ detection efficiency was used to analyze large and non-standard geometry samples and standard-less compositional characterization was carried out for zircaloys and stainless steels. PIGE methods using proton beams were standardized for quantification of low Z elements (Li to Ti) and applied for compositional analysis of borosilicate glass and lithium titanate (Li 2 TiO 3 ) samples and quantification of total B and its isotopic composition of B ( 10 B/ 11 B) in boron based neutron absorbers like B 4 C. (author)

Welcome from INMM (Institute of Nuclear Materials Management)

International Nuclear Information System (INIS)

Satkowiak, L.

2015-01-01

The Institute of Nuclear Materials Management (INMM) is the premier professional society focused on safe and secure use of Nuclear Materials and the related nuclear scientific technology and knowledge. Its international membership includes government, academia, non-governmental organizations and industry, spanning the full spectrum all the way from policy to technology. The Institute's primary role include the promotion of research, the establishment of standards and the development of best practices, all centered around nuclear materials. It then disseminates this information through meetings, professional contacts, reports, papers, discussions, and publications. The formal structure of the INMM includes six technical divisions: Facility Operation; Materials Control and Accountability; Nonproliferation and Arms Control; Nuclear Security and Physical Protection; Packaging, Transportation and Disposition

Resources of nuclear fuels and materials

Energy Technology Data Exchange (ETDEWEB)

Kawamura, K [Tokyo Inst. of Tech. (Japan); Kamiyama, Teiji; Hayashi, S; Hida, Noboru; Okano, T

1974-11-01

In this explanatory article, data on the world resources of nuclear fuels and materials, their production, and the present state of utilization are presented by specialists in varied fields. Main materials taken up are uranium, thorium, beryllium, zirconium, niobium, rare earth elements, graphite, and materials for nuclear fusion (heavy hydrogen and tritium). World reserves and annual production of these materials listed in a number of tables are cited from statistics of the period 1970-1973 or given by estimation. These data may be used as valuable numerical data for various projects and problems of atomic power industries.

Nuclear material accounting software for Ukraine

International Nuclear Information System (INIS)

Doll, M.; Ewing, T.; Lindley, R.; McWilliams, C.; Roche, C.; Sakunov, I.; Walters, G.

1999-01-01

Among the needs identified during initial surveys of nuclear facilities in Ukraine was improved accounting software for reporting material inventories to the regulatory body. AIMAS (Automated Inventory/Material Accounting System) is a PC-based application written in Microsoft Access that was jointly designed by an US/Ukraine development team. The design is highly flexible and configurable, and supports a wide range of computing infrastructure needs and facility requirements including situations where networks are not available or reliable. AIMAS has both English and Russian-language options for displays and reports, and it operates under Windows 3.1, 95, or NT 4.0trademark. AIMAS functions include basic physical inventory tracking, transaction histories, reporting, and system administration functions (system configuration, security, data backup and recovery). Security measures include multilevel password access control, all transactions logged with the user identification, and system administration control. Interfaces to external modules provide nuclear fuel burn-up adjustment and barcode scanning capabilities for physical inventory taking. AIMAS has been installed at Kiev Institute of Nuclear Research (KINR), South Ukraine Nuclear Power Plant (SUNPP), Kharkov Institute of Physics and Technology (KIPT), Sevastopol Institute of Nuclear Energy and Industry (SINEI), and the Ministry of Environmental Protection and Nuclear Safety/Nuclear Regulatory Administration (MEPNS/NRA). Facility specialists are being trained to use the application to track material movement and report to the national regulatory authority

The national nuclear material tracking system. A Korea's countermeasure against nuclear terrorism

International Nuclear Information System (INIS)

Moon, Joo Hyun

2011-01-01

Since nuclear terrorism has been identified as a real threat, the Korean government has earnestly developed elementary technologies and sub-systems for establishing an integrated defensive system against nuclear terrorism, which is based on the concept of defense-in-depth. This paper introduces the gist and implications of the studies that have been conducted in building the national nuclear material tracking system for preventing and intercepting the illicit trafficking and transporting of nuclear material in Korea. (orig.)

Order for execution of the law concerning regulations of nuclear source materials, nuclear fuel materials and reactors

International Nuclear Information System (INIS)

1978-01-01

Under the above mentioned law this order prescribes the procedures of controls given to the persons who wish to conduct refining and fabricating businesses, to construct and operate reactors, and to use nuclear source materials, nuclear fuel materials and internationally controlled materials. The common controlling principle prescribed is that the permission or authorization necessary for above listed businesses should be applied for at each factory or each place of business. Based on the principle, the order prescribes: the procedures to apply for the authorization of the refining business, the permission of the change thereof, and the permission of the fabricating business and the change, thereof (the 1st chapter); the procedures to apply for the permission of the construction of reactors and of the change of the construction, as well as the procedure to do periodic inspections of reactor facilities (the 2nd chapter); the procedures to apply for the permission to use nuclear fuel materials and to change the use thereof, the submission of the report to use nuclear source materials, as well as the procedure to apply for the permission to use internationally controlled materials. In the 4th chapter the order lists up the items on which the competent Ministers may require reports from the person who carries on the relevant business. (Matsushima, A.)

The regulations concerning the uses of nuclear source materials

International Nuclear Information System (INIS)

1981-01-01

This rule is established under the provisions of the law concerning the regulation of nuclear raw materials, nuclear fuel materials and nuclear reactors and the ordinance for the execution of this law, and to enforce them. Basic terms are defined, such as exposure radiation dose, cumulative dose, control area, surrounding monitoring area, worker and radioactive waste. Nuclear raw materials shall be used at the facilities for using them, and control areas and surrounding monitoring areas shall be set up. Cumulative dose and exposure radiation dose of workers shall not exceed the permissible quantities defined by the General Director of the Science and Technology Agency. Records shall be made in each works or enterprise on the accept, delivery and stock of each kind of nuclear raw materials, radiation control and the accidents in the facilities of using nuclear raw materials, and kept for specified periods, respectively. The users of nuclear raw materials shall present reports in each works or enterprise on the stock of these materials on July 30 and December 31, every year. They shall submit reports immediately to the Director General on the particular accidents concerning nuclear raw materials and their facilities and on the circumstances and the measures taken against such accidents within ten days. These reports shall be presented on internationally regulated raw materials too. (Okada, K.)

Nuclear material statistical accountancy system

International Nuclear Information System (INIS)

Argentest, F.; Casilli, T.; Franklin, M.

1979-01-01

The statistical accountancy system developed at JRC Ispra is refered as 'NUMSAS', ie Nuclear Material Statistical Accountancy System. The principal feature of NUMSAS is that in addition to an ordinary material balance calcultation, NUMSAS can calculate an estimate of the standard deviation of the measurement error accumulated in the material balance calculation. The purpose of the report is to describe in detail, the statistical model on wich the standard deviation calculation is based; the computational formula which is used by NUMSAS in calculating the standard deviation and the information about nuclear material measurements and the plant measurement system which are required as data for NUMSAS. The material balance records require processing and interpretation before the material balance calculation is begun. The material balance calculation is the last of four phases of data processing undertaken by NUMSAS. Each of these phases is implemented by a different computer program. The activities which are carried out in each phase can be summarised as follows; the pre-processing phase; the selection and up-date phase; the transformation phase, and the computation phase

The U.S. national nuclear forensics library, nuclear materials information program, and data dictionary

International Nuclear Information System (INIS)

Lamont, Stephen Philip; Brisson, Marcia; Curry, Michael

2011-01-01

Nuclear forensics assessments to determine material process history requires careful comparison of sample data to both measured and modeled nuclear material characteristics. Developing centralized databases, or nuclear forensics libraries, to house this information is an important step to ensure all relevant data will be available for comparison during a nuclear forensics analysis and help expedite the assessment of material history. The approach most widely accepted by the international community at this time is the implementation of National Nuclear Forensics libraries, which would be developed and maintained by individual nations. This is an attractive alternative toan international database since it provides an understanding that each country has data on materials produced and stored within their borders, but eliminates the need to reveal any proprietary or sensitive information to other nations. To support the concept of National Nuclear Forensics libraries, the United States Department of Energy has developed a model library, based on a data dictionary, or set of parameters designed to capture all nuclear forensic relevant information about a nuclear material. Specifically, information includes material identification, collection background and current location, analytical laboratories where measurements were made, material packaging and container descriptions, physical characteristics including mass and dimensions, chemical and isotopic characteristics, particle morphology or metallurgical properties, process history including facilities, and measurement quality assurance information. While not necessarily required, it may also be valuable to store modeled data sets including reactor burn-up or enrichment cascade data for comparison. It is fully expected that only a subset of this information is available or relevant to many materials, and much of the data populating a National Nuclear Forensics library would be process analytical or material accountability

Nuclear materials transportation

International Nuclear Information System (INIS)

Ushakov, B.A.

1986-01-01

Various methods of nuclear materials transportation at different stages of the fuel cycle (U 3 O 8 , UF 6 production enrichment, fuel element manufacturing, storage) are considered. The advantages and drawbacks of railway, automobile, maritime and air transport are analyzed. Some types of containers are characterized

Evaluation of Terminated Nuclear Material Licenses

International Nuclear Information System (INIS)

Spencer, K.M.; Zeighami, E.A.

1999-01-01

This report presents the results of a six-year project that reviewed material licenses that had been terminated during the period from inception of licensing until approximately late-1994. The material licenses covered in the review project were Part 30, byproduct material licenses; Part 40, source material licenses; and Part 70, special nuclear material licenses. This report describes the methodology developed for the project, summarizes the findings of the license file inventory process, and describes the findings of the reviews or evaluations of the license files. The evaluation identified nuclear material use sites that need review of the licensing material or more direct follow-up of some type. The review process also identified licenses authorized to possess sealed sources for which there was incomplete or missing documentation of the fate of the sources

Materials. The Argentine nuclear policy

International Nuclear Information System (INIS)

Strasser, H.

1982-01-01

Part A of the volume contains a literature search on proliferation and the Third World and on the nuclear technology of Argentina. The materials in part B are divided in: 1. Nonproliferation discussion and the Third World. 2. Development and state of nuclear technology in Argentina. 3. Argentina's international contacts in the field of nuclear energy 1. Federal Republic of Germany, 2. Soviet Union, 3. Brazil. (orig./HP) [de

The establishment of computer system for nuclear material accounting

International Nuclear Information System (INIS)

Hong, Jong Sook; Lee, Byung Doo; Park, Ho Joon

1988-01-01

Computer based nuclear material accountancy system will not only increase the credibility of KOREA-IAEA safeguards agreement and bilateral agreements but also decrease the man-power needed to carry out the inspection activity at state level and at facility level. Computer software for nuclear material accounting for and control has been materialized the application to both item and bulk facilities and software for database at state level has been also established to maintain up -to-date status of nation-wide nuclear material inventory. Computer recordings and reporting have been realized to fulfill the national and international commitments to nuclear material accounting for and control. The exchange of information related to nuclear material accounting for has become possible by PC diskettes. (Author)

Standard guide for application of radiation monitors to the control and physical security of special nuclear material

CERN Document Server

American Society for Testing and Materials. Philadelphia

1999-01-01

1.1 This guide briefly describes the state-of-the-art of radiation monitors for detecting special nuclear material (SNM) (see 3.1.11) in order to establish the context in which to write performance standards for the monitors. This guide extracts information from technical documentation to provide information for selecting, calibrating, testing, and operating such radiation monitors when they are used for the control and protection of SNM. This guide offers an unobtrusive means of searching pedestrians, packages, and motor vehicles for concealed SNM as one part of a nuclear material control or security plan for nuclear materials. The radiation monitors can provide an efficient, sensitive, and reliable means of detecting the theft of small quantities of SNM while maintaining a low likelihood of nuisance alarms. 1.2 Dependable operation of SNM radiation monitors rests on selecting appropriate monitors for the task, operating them in a hospitable environment, and conducting an effective program to test, calibrat...

A future vision of nuclear material information systems

International Nuclear Information System (INIS)

Suski, N.; Wimple, C.

1999-01-01

To address the current and future needs for nuclear materials management and safeguards information, Lawrence Livermore National Laboratory envisions an integrated nuclear information system that will support several functions. The vision is to link distributed information systems via a common communications infrastructure designed to address the information interdependencies between two major elements: Domestic, with information about specific nuclear materials and their properties, and International, with information pertaining to foreign nuclear materials, facility design and operations. The communication infrastructure will enable data consistency, validation and reconciliation, as well as provide a common access point and user interface for a broad range of nuclear materials information. Information may be transmitted to, from, and within the system by a variety of linkage mechanisms, including the Internet. Strict access control will be employed as well as data encryption and user authentication to provide the necessary information assurance. The system can provide a mechanism not only for data storage and retrieval, but will eventually provide the analytical tools necessary to support the U.S. government's nuclear materials management needs and non-proliferation policy goals

A review on nuclear forensic methodology for analysis of nuclear material of unknown origin

International Nuclear Information System (INIS)

Deshmukh, A.V.; Raghav, N.K.; Fatangare, N.M.; Jagtap, S.S.

2014-01-01

With the growing use of nuclear power and threat from illegal nuclear smuggling nuclear forensic provides an aid to the law enforcement to trace back modus operandi of such threats. Extensive nuclear proliferation, race among countries to acquire nuclear capability and global terrorism scenario has mandated Nuclear Forensic Science technology to tackle nuclear threats. Gamma spectrometry, alpha spectrometry, thermal ionization mass spectrometry, inductively coupled plasma mass spectrometry are employed for characterization and relative isotopic composition determinant of Nuclear material and techniques like SEM transmission electron TEM, FT-IR, GC-MS, Electrophoretic technique are used to characterize the contaminated materials in order to deceive investigative agencies. The present paper provide systematic forensic methodology for nuclear and radioactive materials encountered at any crime scene due to any accidental discharges or military activities. (author)

Tungsten - Yttrium Based Nuclear Structural Materials

Science.gov (United States)

Ramana, Chintalapalle; Chessa, Jack; Martinenz, Gustavo

2013-04-01

The challenging problem currently facing the nuclear science community in this 21st century is design and development of novel structural materials, which will have an impact on the next-generation nuclear reactors. The materials available at present include reduced activation ferritic/martensitic steels, dispersion strengthened reduced activation ferritic steels, and vanadium- or tungsten-based alloys. These materials exhibit one or more specific problems, which are either intrinsic or caused by reactors. This work is focussed towards tungsten-yttrium (W-Y) based alloys and oxide ceramics, which can be utilized in nuclear applications. The goal is to derive a fundamental scientific understanding of W-Y-based materials. In collaboration with University of Califonia -- Davis, the project is designated to demonstrate the W-Y based alloys, ceramics and composites with enhanced physical, mechanical, thermo-chemical properties and higher radiation resistance. Efforts are focussed on understanding the microstructure, manipulating materials behavior under charged-particle and neutron irradiation, and create a knowledge database of defects, elemental diffusion/segregation, and defect trapping along grain boundaries and interfaces. Preliminary results will be discussed.

Capacitor-based detection of nuclear magnetization: nuclear quadrupole resonance of surfaces.

Science.gov (United States)

Gregorovič, Alan; Apih, Tomaž; Kvasić, Ivan; Lužnik, Janko; Pirnat, Janez; Trontelj, Zvonko; Strle, Drago; Muševič, Igor

2011-03-01

We demonstrate excitation and detection of nuclear magnetization in a nuclear quadrupole resonance (NQR) experiment with a parallel plate capacitor, where the sample is located between the two capacitor plates and not in a coil as usually. While the sensitivity of this capacitor-based detection is found lower compared to an optimal coil-based detection of the same amount of sample, it becomes comparable in the case of very thin samples and even advantageous in the proximity of conducting bodies. This capacitor-based setup may find its application in acquisition of NQR signals from the surface layers on conducting bodies or in a portable tightly integrated nuclear magnetic resonance sensor. Copyright © 2010 Elsevier Inc. All rights reserved.

Assessment of 222Rn occupational exposure at IPEN nuclear materials storage site, SP, Brazil

International Nuclear Information System (INIS)

Caccuri, Lilian Saueia

2007-01-01

In this study it was assessed the occupational exposure to 222 Rn at IPEN, SP, Brazil, nuclear materials storage site through the committed effective dose received by workers exposed to this radionuclide. The radiation dose was calculated through the radon concentrations at nuclear materials storage site. Radon concentrations were determined by passive detection method with solid state nuclear detectors (SSNTD). The SSNTD used in this study was the polycarbonate Makrofol E; each detector is a small square plastic of 1 cm 2 , placed into a diffusion chamber type KFK. It was monitored 14 points at nuclear materials storage site and one external point, over a period of 21 months, changing the detectors every three months, from December 2004 to September 2006. The 222 Rn concentrations varied from 196 ± 9 and 2048 ± 81 Bq·m -3 . The committed effective dose due to radon inhalation at IPEN nuclear materials storage site was obtained from radon activity incorporated and dose conversion factor, according to International Commission on Radiological Protection procedures. The effective committed dose received by workers is below 20 mSv·y -1 . This value is suggested as an annual effective dose limit for occupational exposure by ICRP 60. (author)

Order for execution of the law concerning regulations of nuclear source materials, nuclear fuel materials and reactors

International Nuclear Information System (INIS)

1985-01-01

This ordinance is stipulated under the law concerning the regulation of nuclear raw materials, nuclear fuel materials and reactors. The designation for refining and processing businesses under the law shall be obtained for each works or enterprise where these operations are to be practiced. Persons who intend to accept the designation shall file applications attaching business plans and the other documents specified by the ordinances of the Prime Minister's Office and other ministry orders. The permission for the installation of nuclear reactors under the law shall be received for each works or enterprise where reactors are to be set up. Persons who intend to get the permission shall file applications attaching the financing plans required for the installation of reactors and the other documents designated by the orders of the competent ministry. The permission concerning the reactors installed on foreign ships shall be obtained for each ship which is going to enter into the Japanese waters. Persons who ask for the permission shall file applications attaching the documents which explain the safety of reactor facilities and the other documents defined by the orders of the Ministry of Transportation. The designation for reprocessing business and the application for it are provided for, respectively. The usage of nuclear fuel materials, nuclear raw materials and internationally regulated goods is ruled in detail. (Kubozone, M.)

Order for execution of the law concerning regulations of nuclear source materials, nuclear fuel materials and reactors

International Nuclear Information System (INIS)

1981-01-01

This ordinance is stipulated under the law concerning the regulation of nuclear raw materials, nuclear fuel materials and reactors. The designation for refining and processing businesses under the law shall be obtained for each works or enterprise where these operations are to be practiced. Persons who intend to accept the designation shall file applications attaching business plans and the other documents specified by the ordinances of the Prime Minister's Office and other ministry orders. The permission for the installation of nuclear reactors under the law shall be received for each works or enterprise where reactors are to be set up. Persons who intend to get the permission shall file applications attaching the financing plans required for the installation of reactors and the other documents designated by the orders of the competent ministry. The permission concerning the reactors installed on foreign ships shall be obtained for each ship which is going to enter into the Japanese waters. Persons who ask for the permission shall file applications attaching the documents which explain the safety of reactor facilities and the other documents defined by the orders of the Ministry of Transportation. The designation for reprocessing business and the application for it are provided for, respectively. The usage of nuclear fuel materials, nuclear raw materials and internationally regulated goods is ruled in detail.(Okada, K.)

RADIATION EFFECTS IN NUCLEAR WASTE MATERIALS

International Nuclear Information System (INIS)

Weber, William J.

2000-01-01

The objective of this research was to develop fundamental understanding and predictive models of radiation effects in glasses and ceramics at the atomic, microscopic, and macroscopic levels, as well as an understanding of the effects of these radiation-induced solid-state changes on dissolution kinetics (i.e., radionuclide release). The research performed during the duration of this project has addressed many of the scientific issues identified in the reports of two DOE panels [1,2], particularly those related to radiation effects on the structure of glasses and ceramics. The research approach taken by this project integrated experimental studies and computer simulations to develop comprehensive fundamental understanding and capabilities for predictive modeling of radiation effects and dissolution kinetics in both glasses and ceramics designed for the stabilization and immobilization of high-level tank waste (HLW), plutonium residues and scraps, surplus weapons plutonium, other actinides, and other highly radioactive waste streams. Such fundamental understanding is necessary in the development of predictive models because all experimental irradiation studies on nuclear waste materials are ''accelerated tests'' that add a great deal of uncertainty to predicted behavior because the damage rates are orders of magnitude higher than the actual damage rates expected in nuclear waste materials. Degradation and dissolution processes will change with damage rate and temperature. Only a fundamental understanding of the kinetics of all the physical and chemical processes induced or affected by radiation will lead to truly predictive models of long-term behavior and performance for nuclear waste materials. Predictive models of performance of nuclear waste materials must be scientifically based and address both radiation effects on structure (i.e., solid-state effects) and the effects of these solid-state structural changes on dissolution kinetics. The ultimate goal of this

Croatian National System of Nuclear Materials Control

International Nuclear Information System (INIS)

Biscan, R.

1998-01-01

In the process of economic and technological development of Croatia by using or introducing nuclear power or in the case of international co-operation in the field of peaceful nuclear activities, including international exchange of nuclear material, Croatia should establish and implement National System of Nuclear Materials Control. Croatian National System of accounting for and control of all nuclear material will be subjected to safeguards under requirements of Agreement and Additional Protocol between the Republic of Croatia and the International Atomic Energy Agency (IAEA) for the Application of Safeguards in Connection with the Treaty on the Non-Proliferation of Nuclear Weapons (NPT). The decision by NPT parties at the 1995 NPT Review and Extension Conference to endorse the Fullscope IAEA Safeguards Standard (FSS) as a necessary precondition of nuclear supply means that states are obliged to ensure that the recipient country has a FSS agreement in place before any nuclear transfer can take place (Ref. 1). The FSS standard of nuclear supply is a central element of the Nuclear Suppliers Group (NSG) Guidelines which the NSG adopted in 1992 and should be applied to members and non-members of the NSG. The FSS standard of nuclear supply in general allows for NPT parties or countries which have undertaken the same obligations through other treaty arrangements, to receive favourable treatment in nuclear supply arrangements. However, the Iraqi experience demonstrate that trade in nuclear and dual-use items, if not properly monitored, can contribute to a nuclear weapons program in countries acting contrary to their non-proliferation obligation. Multilateral nuclear export control mechanisms, including the FSS supply standard, provide the basis for co-ordination and standardisation of export control measures. (author)

Software development for managing nuclear material database