Surfactant media to grow new crystalline cobalt 1,3,5-benzenetricarboxylate metal-organic frameworks

KAUST Repository

Lu, Haisheng; Bai, Linlu; Xiong, Weiwei; Li, Peizhou; Ding, Junfeng; Zhang, Guodong; Wu, Tao; Zhao, Yanli; Lee, Jongmin; Yang, Yanhui; Geng, Baoyou; Zhang, Qichun

2014-01-01

In this report, three new metal-organic frameworks (MOFs), [Co 3(μ3-OH)(HBTC)(BTC)2Co(HBTC)]·(HTEA) 3·H2O (NTU-Z30), [Co(BTC)] ·HTEA·H2O (NTU-Z31), [Co3(BTC) 4]·(HTEA)4 (NTU-Z32), where H3BTC = 1,3,5-benzenetricarboxylic acid, TEA = triethylamine

Comparison of the Performance of Poly Aluminum Chloride with Natural Co-coagulants in Removal of Turbidity from synthetic aqueous solution

Directory of Open Access Journals (Sweden)

Leila Mosleh

2014-06-01

Full Text Available Background: Contaminated water, naturally or by human, should be processed to become drinking water. Coagulation is a process that fine unsettling particles which called colloids and are important factors in the turbidity occurrence, join together and settle. The purpose of this study was to evaluate and comparison of the performance of poly aluminum chloride accompany with corn starch and okra, as a co-coagulant agent, to remove turbidity from water. Methods: This research was descriptive-functional study. In this study, the effect of two natural co-coagulant agents, corn starch and okra, with poly aluminum chloride were evaluated and R and SAS software were used in order to experimental design and data analysis. Also, after the analysis of variance, LSD test was used to compare treatment averages. Results: In the initial turbidity of 250 NTU, poly aluminum chloride and corn starch (5 ppm and 0.7 ppm, respectively, the highest percentage of turbidity removal was observed which could reduce the turbidity up to 98.48% and reached at 3.73 NTU. Moreover, in the initial turbidity of 500 NTU, maximum turbidity reduction related to poly aluminum chloride and okra (5 ppm and 0.7 ppm, respectively which reduced the turbidity up to 98.38% and reached at 8.1 NTU. Conclusions: As an economic aspect, replacement of natural polymers with synthetic polymers which have higher costs is economic and also higher turbidity reduction may be observed in compare with using chemical coagulants, solely. In addition, chemical coagulants consumption reduces, however more researches must be conducted on residual natural co-coagulants and interactions between chemical and natural and also their health effects on consumers.

Comparison of the Performance of Corn Starch Coagulant Aid Accompany with Alum, Polyaluminum Chloride and Ferric Chloride Coagulants in Turbidity Removal from Water

Directory of Open Access Journals (Sweden)

Leila Mosleh

2014-09-01

Full Text Available Background: The most important process in water treatment plant is coagulation and flocculation. Regular chemical coagulant which used in Iran are aluminum sulfate (Alum and ferric chloride. Chemical coagulants have hazardous effect on human health and their cost is high for developing country. The purpose of this study was to evaluate the comparison of chemical coagulants accompany with corn starch as a coagulant aid, for the turbidity removal from water. Methods: This study was accomplished in pilot-scale with synthetic turbid water using clay. In this research, initial turbidity of 250 and 500 NTU was experimented. Chemical coagulant dose during the experiment was 1, 2 and 5 ppm and natural coagulant dose was 0, 0.1, 0.3, 0.5 and 0.7 ppm. Results: The results showed that maximum removal efficiency of turbidity in initial turbidity of 250 NTU belonged to poly aluminum chloride with 5 ppm dosage and corn starch with 0.7 ppm dosage which removed and reduced the initial turbidity to 98.48% and 3.73 NTU, respectively. Moreover, in initial turbidity of 500 NTU the maximum removal efficiency was 98.52% which belonged to ferric chloride and corn starch (5 and 0.7 ppm respectively and reduced the initial turbidity to 7.4 NTU. Conclusions: The results of this study showed that using natural coagulant aid reduce the chemical coagulant consumption, and also does not have significant effect on pH range and reduce the health risks. While huge amount of required polyelectrolytes for water treatment plant imported to the country and the production of corn starch in our country is high, it is hope that the results of this project can be used in industrial scale.

Assessments at multiple levels of biological organization allow for an integrative determination of physiological tolerances to turbidity in an endangered fish species.

Science.gov (United States)

Hasenbein, Matthias; Fangue, Nann A; Geist, Juergen; Komoroske, Lisa M; Truong, Jennifer; McPherson, Rina; Connon, Richard E

2016-01-01

Turbidity can influence trophic levels by altering species composition and can potentially affect fish feeding strategies and predator-prey interactions. The estuarine turbidity maximum, described as an area of increased suspended particles, phytoplankton and zooplankton, generally represents a zone with higher turbidity and enhanced food sources important for successful feeding and growth in many fish species. The delta smelt (Hypomesus transpacificus) is an endangered, pelagic fish species endemic to the San Francisco Estuary and Sacramento-San Joaquin River Delta, USA, where it is associated with turbid waters. Turbidity is known to play an important role for the completion of the species' life cycle; however, turbidity ranges in the Delta are broad, and specific requirements for this fish species are still unknown. To evaluate turbidity requirements for early life stages, late-larval delta smelt were maintained at environmentally relevant turbidity levels ranging from 5 to 250 nephelometric turbidity units (NTU) for 24 h, after which a combination of physiological endpoints (molecular biomarkers and cortisol), behavioural indices (feeding) and whole-organism measures (survival) were determined. All endpoints delivered consistent results and identified turbidities between 25 and 80 NTU as preferential. Delta smelt survival rates were highest between 12 and 80 NTU and feeding rates were highest between 25 and 80 NTU. Cortisol levels indicated minimal stress between 35 and 80 NTU and were elevated at low turbidities (5, 12 and 25 NTU). Expression of stress-related genes indicated significant responses for gst, hsp70 and glut2 in high turbidities (250 NTU), and principal component analysis on all measured genes revealed a clustering of 25, 35, 50 and 80 NTU separating the medium-turbidity treatments from low- and high-turbidity treatments. Taken together, these data demonstrate that turbidity levels that are either too low or too high affect delta

Purification and detoxification of petroleum refinery wastewater by electrocoagulation process.

Science.gov (United States)

Gousmi, N; Sahmi, A; Li, H Z; Poncin, S; Djebbar, R; Bensadok, K

2016-09-01

The treatment of synthetic oily wastewater having the characteristics of a typical petroleum refinery wastewater (PRW) by electrocoagulation (EC) using iron and aluminum electrodes was conducted in an electrolytic reactor equipped with fluid recirculation. During the treatment, the emulsion stability was followed by the measurement of Zeta potential and particle sizes. Effects of some operating conditions such as electrodes material, current density and electrolysis time on removal efficiencies of turbidity, and chemical oxygen demand (COD) were investigated in detail. The PRW purification by the EC process was found to be the most effective using aluminum as the anode and cathode, current density of 60 A/m(2) and 30 min of electrolysis time. Under these conditions, the process efficiencies were 83.52% and 99.94%, respectively, for COD and turbidity removals which correspond to final values of 96 mg O2/L and 0.5 NTU. A moderate energy consumption (0.341 kWh) was needed to treat 1 m(3) of PRW. Besides, the ecotoxicity test proved that toxic substances presented in the PRW, and those inhibiting the germination growth of whet, were eliminated by the EC technique.

Inheritance of Properties in NTU Communication Situations

NARCIS (Netherlands)

Hendrickx, R.L.P.

2002-01-01

In this paper we consider communication situations in which utility is nontransferable. We compare this model with the more familiar model of transferable utility communication situations and point out an odd feature of the latter. We mainly focus on the inheritance of properties of the underlying

A cooperative game-theoretic framework for negotiating marine spatial allocation agreements among heterogeneous players.

Science.gov (United States)

Kyriazi, Zacharoula; Lejano, Raul; Maes, Frank; Degraer, Steven

2017-02-01

Marine spatial allocation has become, in recent decades, a political flashpoint, fuelled by political power struggles, as well as the continuously increasing demand for marine space by both traditional and emerging marine uses. To effectively address this issue, we develop a decision-making procedure, that facilitates the distribution of disputed areas of specific size among heterogeneous players in a transparent and ethical way, while considering coalitional formations through coexistence. To do this, we model players' alternative strategies and payoffs within a cooperative game-theoretic framework. Depending on whether transferable utility (TU) or non-transferable utility (NTU) is the more appropriate assumption, we illustrate the use of the TU Shapley value and the Lejano's fixed point NTU Shapley value to solve for the ideal allocations. The applicability and effectiveness of the process has been tested in a case study area, the Dogger Bank Special Area of Conservation in the North Sea, which involves three totally or partially conflicting activities, i.e. fishing, nature conservation and wind farm development. The findings demonstrate that the process is capable of providing a unique, fair and equitable division of space Finally, among the two solution concepts proposed the fixed point NTU Shapley value manages to better address the heterogeneity of the players and thus to provide a more socially acceptable allocation that favours the weaker player, while demonstrating the importance of the monetary valuation attributed by each use to the area. Copyright © 2016 Elsevier Ltd. All rights reserved.

Factors influencing arsenic and nitrate removal from drinking water in a continuous flow electrocoagulation (EC) process

International Nuclear Information System (INIS)

Kumar, N. Sanjeev; Goel, Sudha

2010-01-01

An experimental study was conducted under continuous flow conditions to evaluate some of the factors influencing contaminant removal by electrocoagulation (EC). A bench-scale simulation of drinking water treatment was done by adding a filtration column after a rectangular EC reactor. Contaminant removal efficiency was determined for voltages ranging from 10 to 25 V and a comparative study was done with distilled water and tap water for two contaminants: nitrate and arsenic(V). Maximum removal efficiency was 84% for nitrate at 25 V and 75% for arsenic(V) at 20 V. No significant difference in contaminant removal was observed in tap water versus distilled water. Increase in initial As(V) concentration from 1 ppm to 2 ppm resulted in a 10% increase in removal efficiency. Turbidity in the EC reactor effluent was 52 NTU and had to be filtered to achieve acceptable levels of final turbidity (5 NTU) at steady-state. The flow regime in the continuous flow reactor was also evaluated in a tracer study to determine whether it is a plug flow reactor (PFR) or constantly stirred tank reactor (CSTR) and the results show that this reactor was close to an ideal CSTR, i.e., it was fairly well-mixed.

Factors influencing arsenic and nitrate removal from drinking water in a continuous flow electrocoagulation (EC) process

Energy Technology Data Exchange (ETDEWEB)

Kumar, N. Sanjeev [Civil Engineering Department, IIT Kharagpur, Kharagpur 721302 (India); Goel, Sudha, E-mail: sudhagoel@civil.iitkgp.ernet.in [Civil Engineering Department, IIT Kharagpur, Kharagpur 721302 (India)

2010-01-15

An experimental study was conducted under continuous flow conditions to evaluate some of the factors influencing contaminant removal by electrocoagulation (EC). A bench-scale simulation of drinking water treatment was done by adding a filtration column after a rectangular EC reactor. Contaminant removal efficiency was determined for voltages ranging from 10 to 25 V and a comparative study was done with distilled water and tap water for two contaminants: nitrate and arsenic(V). Maximum removal efficiency was 84% for nitrate at 25 V and 75% for arsenic(V) at 20 V. No significant difference in contaminant removal was observed in tap water versus distilled water. Increase in initial As(V) concentration from 1 ppm to 2 ppm resulted in a 10% increase in removal efficiency. Turbidity in the EC reactor effluent was 52 NTU and had to be filtered to achieve acceptable levels of final turbidity (5 NTU) at steady-state. The flow regime in the continuous flow reactor was also evaluated in a tracer study to determine whether it is a plug flow reactor (PFR) or constantly stirred tank reactor (CSTR) and the results show that this reactor was close to an ideal CSTR, i.e., it was fairly well-mixed.

The effect of turbidity levels and Moringa oleifera concentration on the effectiveness of coagulation in water treatment.

Science.gov (United States)

Nkurunziza, T; Nduwayezu, J B; Banadda, E N; Nhapi, I

2009-01-01

Laboratory experiments were carried out to assess the water purification and antimicrobial properties of Moringa oleifera (MO). Hence different concentrations (25 to 300 mg/L) were prepared from a salt (1 M NaCl) extract of MO fine powder and applied to natural surface water whose turbidity levels ranged from 50 to 450 NTU. The parameters determined before and after coagulation were turbidity, pH, colour, hardness, iron, manganese and Escherichia coli. The experiments showed that turbidity removal is influenced by the initial turbidity since the lowest turbidity removal of 83.2% was observed at 50 NTU, whilst the highest of 99.8% was obtained at 450 NTU. Colour removal followed the same trend as the turbidity. The pH exhibited slight variations through the coagulation. The hardness removal was very low (0 to 15%). However, high removals were achieved for iron (90.4% to 100%) and manganese (93.1% to 100%). The highest E. coli removal achieved was 96.0%. Its removal was associated with the turbidity removal. The optimum MO dosages were 150 mg/L (50 NTU and 150 NTU) and 125 mg/L for the rest of the initial turbidity values. Furthermore all the parameters determined satisfied the WHO guidelines for drinking water except for E. coli.

Surfactant-thermal method to prepare two new cobalt metal-organic frameworks

Energy Technology Data Exchange (ETDEWEB)

Yu, Xianglin [School of Materials Science and Engineering and School of Chemical and Biomedical Engineering, Nanyang Technological University, Singapore 639798 (Singapore); Key Laboratory for Green Chemical Process of Ministry of Education, School of Chemical Engineering and Pharmacy, Wuhan Institute of Technology, Wuhan 430074 (China); Toh, Yong Siang [School of Materials Science and Engineering and School of Chemical and Biomedical Engineering, Nanyang Technological University, Singapore 639798 (Singapore); Zhao, Jun [College of Materials and Chemical Engineering, Hubei Provincial Collaborative Innovation Center for New Energy Microgrid, China Three Gorges University, Yichang 443002 (China); Nie, Lina [School of Materials Science and Engineering and School of Chemical and Biomedical Engineering, Nanyang Technological University, Singapore 639798 (Singapore); Ye, Kaiqi; Wang, Yue [State Key Laboratory of Supramolecular Structure and Materials, College of Chemistry, Jilin University, Changchun 130012 (China); Li, Dongsheng [College of Materials and Chemical Engineering, Hubei Provincial Collaborative Innovation Center for New Energy Microgrid, China Three Gorges University, Yichang 443002 (China); Zhang, Qichun, E-mail: qczhang@ntu.edu.sg [School of Materials Science and Engineering and School of Chemical and Biomedical Engineering, Nanyang Technological University, Singapore 639798 (Singapore); Division of Chemistry and Biological Chemistry, School of Physical and Mathematical Sciences, Nanyang Technological University, Singapore 637371 (Singapore)

2015-12-15

Employing surfactants as reaction media, two new metal-organic frameworks (MOFs):(HTEA){sub 3}[Co{sub 3}(BTC){sub 3}] (NTU-Z33) and (HTEA)[Co{sub 3}(HBTC){sub 2}(BTC)] (NTU-Z34) (H{sub 3}BTC=1,3,5-benzenetricarboxylic acid, TEA=trimethylamine, and NTU=Nanyang Technological University), have been successfully synthesized and fully characterized. Note that NTU-Z33 has an unusual trimeric [Co{sub 3}(COO){sub 9}] secondary building unit (SBU). Magnetic characterization suggests that both compounds have weak antiferromagnetic behaviors. Our success in preparing new crystalline Co-BTC based MOFs under different surfactant media could provide a new road to prepare new diverse MOFs through various combinations of surfactants. - Graphical abstract: Employing surfactants as reaction media, two new metal-organic frame-works (MOFs) have been successfully synthesized and magnetic study suggests that both compounds have weak antiferromagnetic behaviors. - Highlights: • Two novel metal-organic frame-works (MOFs). • Synthesis through surfactant-thermal condition. • weak antiferromagnetic behaviors for both compounds.

Surfactant-thermal method to prepare two new cobalt metal-organic frameworks

International Nuclear Information System (INIS)

Yu, Xianglin; Toh, Yong Siang; Zhao, Jun; Nie, Lina; Ye, Kaiqi; Wang, Yue; Li, Dongsheng; Zhang, Qichun

2015-01-01

Employing surfactants as reaction media, two new metal-organic frameworks (MOFs):(HTEA)_3[Co_3(BTC)_3] (NTU-Z33) and (HTEA)[Co_3(HBTC)_2(BTC)] (NTU-Z34) (H_3BTC=1,3,5-benzenetricarboxylic acid, TEA=trimethylamine, and NTU=Nanyang Technological University), have been successfully synthesized and fully characterized. Note that NTU-Z33 has an unusual trimeric [Co_3(COO)_9] secondary building unit (SBU). Magnetic characterization suggests that both compounds have weak antiferromagnetic behaviors. Our success in preparing new crystalline Co-BTC based MOFs under different surfactant media could provide a new road to prepare new diverse MOFs through various combinations of surfactants. - Graphical abstract: Employing surfactants as reaction media, two new metal-organic frame-works (MOFs) have been successfully synthesized and magnetic study suggests that both compounds have weak antiferromagnetic behaviors. - Highlights: • Two novel metal-organic frame-works (MOFs). • Synthesis through surfactant-thermal condition. • weak antiferromagnetic behaviors for both compounds.

Situation analysis of water quality in the Umtata River catchment ...

African Journals Online (AJOL)

The Umtata River was characterised by using standard physico-chemical and microbiological methods to assess the present water quality in the river. The results indicated high turbidity, gross microbiological and cadmium pollution. Turbidity values ranged from 0.28 NTU to 1 899 NTU highlighting the known problem of ...

A hybrid froth flotation-filtration system as a pretreatment for oil sands tailings pond recycle water management: Bench- and pilot-scale studies.

Science.gov (United States)

Loganathan, Kavithaa; Bromley, David; Chelme-Ayala, Pamela; Gamal El-Din, Mohamed

2015-09-15

Through sustainable water management, oil sands companies are working to reduce their reliance on fresh water by minimizing the amount of water required for their operations and by recycling water from tailings ponds. This study was the first pilot-scale testing of a hybrid technology consisting of froth flotation combined with filtration through precoated submerged stainless steel membranes used to treat recycle water from an oil sands facility. The results indicated that the most important factor affecting the performance of the hybrid system was the influent water quality. Any rise in the levels of suspended solids or total organic carbon of the feed water resulted in changes of chemical consumption rates, flux rates, and operating cycle durations. The selections of chemical type and dosing rates were critical in achieving optimal performance. In particular, the froth application rate heavily affected the overall recovery of the hybrid system as well as the performance of the flotation process. Optimum surfactant usage to generate froth (per liter of treated water) was 0.25 mL/L at approximately 2000 NTU of influent turbidity and 0.015 mL/L at approximately 200 NTU of influent turbidity. At the tested conditions, the optimal coagulant dose was 80 mg/L (as Al) at approximately 2000 NTU of influent turbidity and recycle water. Copyright © 2015 Elsevier Ltd. All rights reserved.

Water Quality of Hills Water, Supply Water and RO Water Machine at Ulu Yam Selangor

Science.gov (United States)

Ngadiman, N.; ‘I Bahari, N.; Kaamin, M.; Hamid, N. B.; Mokhtar, M.; Sahat, S.

2016-07-01

The rapid development resulted in the deterioration of the quality of drinking water in Malaysia. Recognizing the importance of water quality, new alternatives for drinking water such as mineral water processing from reverse osmosis (RO) machine become more popular. Hence, the demand for mineral water, natural spring water or water from the hills or mountains rose lately. More consumers believed the quality of these spring water better than other source of drinking water. However, the quality of all the drinking water sources is to meet the required quality standard. Therefore, this paper aims to measure the quality of the waters from hills, from RO machine and the water supply in Ulu Yam, Selangor Batang Kali, Malaysia. The water quality was determined based on following parameters: ammoniacal nitrogen (NH3), iron (Fe), turbidity (NTU) and pH. The results show that the water from hills has better quality compared to water supply and water from RO machine. The value of NH3 ranged from 0.03 mg/L- 0.67 mg/L; Fe was from 0.03mg/L - 0.12 mg/L, turbidity at 0.42 NTU - 0.88 NTU and pH is at 6.60 - 0.71. Based on the studied parameters, all three types of water are fit for drinking and have met the required national drinking water quality standard.

Fabrication of an inexpensive photosensitive flow through device for turbidity measurement

International Nuclear Information System (INIS)

Morco, Ryan P.; Dawal, Micah S.; Sucgang, Raymond J.

2014-01-01

The aim of this study is the construction of a portable, simple to use, on-line photosensitive device which measures turbidity in water. The turbidity measuring device uses a light emitting diode, LED, light source shining on a light dependent resistor, LDR, which is connected in series to a circuit supplying a constant voltage and a digital voltmeter, DVM. Light shine through a tube containing the sample, and onto a photosensitive circuit. A clear tube of water is the BLANK and has zero absorbance. A fraction of the incident light that i obstructed by the turbidity of the sample can be used for calculable determination of turbidity in water. The turbidity is related to the absorbance reading, following Beer's law. The amount of incident and transmitted light are expressed in voltage units, by a voltmeter. The sample is delivered into the sampling chamber by a rubber tubing attached to a power head submersible pump which is immersed in the pool of water to be sampled. The instrument shows excellent response over the range o turbidity values (5NTU to 180 NTU). Linearity (R 2= 0.95) has been achieved using the device, working with 6 trials per particular NTU value. The NTU readings of the urbidity meter were calibrated against solutions of varying NTU's measured using a HORIBA multi-parameter probe. The other features of the device include: simplicity of operation, low-cost, rugged, handy and can be used in on-line and flow mode applications. (author)

Polyethersulfone-based ultrafiltration hollow fibre membrane for drinking water treatment systems

Science.gov (United States)

Chew, Chun Ming; Ng, K. M. David; Ooi, H. H. Richard

2017-12-01

Conventional media/sand filtration has been the mainstream water treatment process for most municipal water treatment plants in Malaysia. Filtrate qualities of conventional media/sand filtration are very much dependent on the coagulation-flocculation process prior to filtration and might be as high as 5 NTU. However, the demands for better quality of drinking water through public piped-water supply systems are growing. Polymeric ultrafiltration (UF) hollow fibre membrane made from modified polyethersulfone (PES) material is highly hydrophilic with high tensile strength and produces excellent quality filtrate of below 0.3 NTU in turbidity. This advanced membrane filtration material is also chemical resistance which allows a typical lifespan of 5 years. Comparisons between the conventional media/sand filtration and PES-based UF systems are carried out in this paper. UF has been considered as the emerging technology in municipal drinking water treatment plants due to its consistency in producing high quality filtrates even without the coagulation-flocculation process. The decreasing cost of PES-based membrane due to mass production and competitive pricing by manufacturers has made the UF technology affordable for industrial-scale water treatment plants.

Estimation of CO2 emission from water treatment plant--model development and application.

Science.gov (United States)

Kyung, Daeseung; Kim, Dongwook; Park, Nosuk; Lee, Woojin

2013-12-15

A comprehensive mathematical model developed for this study was used to compare estimates of on-site and off-site CO2 emissions, from conventional and advanced water treatment plants (WTPs). When 200,000 m(3) of raw water at 10 NTU (Nepthelometric Turbidity Unit) was treated by a conventional WTP to 0.1 NTU using aluminum sulfate as a coagulant, the total CO2 emissions were estimated to be 790 ± 228 (on-site) and 69,596 ± 3950 (off-site) kg CO2e/d. The emissions from an advanced WTP containing micro-filtration (MF) membrane and ozone disinfection processes; treating the same raw water to 0.005 NTU, were estimated to be 395 ± 115 (on-site) and 38,197 ± 2922 (off-site) kg CO2e/d. The on-site CO2 emissions from the advanced WTP were half that from the conventional WTP due to much lower use of coagulant. On the other hand, off-site CO2 emissions due to consumption of electricity were 2.14 times higher for the advanced WTP, due to the demands for operation of the MF membrane and ozone disinfection processes. However, the lower use of chemicals in the advanced WTP decreased off-site CO2 emissions related to chemical production and transportation. Overall, total CO2 emissions from the conventional WTP were 1.82 times higher than that from the advanced WTP. A sensitivity analysis was performed for the advanced WTP to suggest tactics for simultaneously reducing CO2 emissions further and enhancing water quality. Copyright © 2013 Elsevier Ltd. All rights reserved.

Correlation of uptake patterns on single-photon emission computed tomography/computed tomography (SPECT/CT)and treatment response in patients with knee pain

International Nuclear Information System (INIS)

Koh, Geon; Hwang, Kyung Hoon; Lee, Hae Jin; Kim, Seog Gyun; Lee, Beom Koo

2016-01-01

To determine whether treatment response in patients with knee pain could be predicted using uptake patterns on single-photon emission computed tomography/computed tomography (SPECT/CT) images. Ninety-five patients with knee pain who had undergone SPECT/CT were included in this retrospective study. Subjects were divided into three groups: increased focal uptake (FTU), increased irregular tracer uptake (ITU), and no tracer uptake (NTU). A numeric rating scale (NRS-11) assessed pain intensity. We analyzed the association between uptake patterns and treatment response using Pearson's chi-square test and Fisher's exact test. Uptake was quantified from SPECT/CT with region of interest (ROI) counting, and an intraclass correlation coefficient (ICC) calculated agreement. We used Student' t-test to calculate statistically significant differences of counts between groups and the Pearson correlation to measure the relationship between counts and initial NRS-1k1. Multivariate logistic regression analysis determined which variables were significantly associated with uptake. The FTU group included 32 patients; ITU, 39; and NTU, 24. With conservative management, 64 % of patients with increased tracer uptake (TU, both focal and irregular) and 36 % with NTU showed positive response. Conservative treatment response of FTU was better than NTU, but did not differ from that of ITU. Conservative treatment response of TU was significantly different from that of NTU (OR 3.1; p 0.036). Moderate positive correlation was observed between ITU and initial NRS-11. Age and initial NRS-11 significantly predicted uptake. Patients with uptake in their knee(s) on SPECT/CT showed positive treatment response under conservative treatment

Correlation of uptake patterns on single-photon emission computed tomography/computed tomography (SPECT/CT)and treatment response in patients with knee pain

Energy Technology Data Exchange (ETDEWEB)

Koh, Geon; Hwang, Kyung Hoon; Lee, Hae Jin; Kim, Seog Gyun; Lee, Beom Koo [Gachon University Gil Hospital, Incheon (Korea, Republic of)

2016-06-15

To determine whether treatment response in patients with knee pain could be predicted using uptake patterns on single-photon emission computed tomography/computed tomography (SPECT/CT) images. Ninety-five patients with knee pain who had undergone SPECT/CT were included in this retrospective study. Subjects were divided into three groups: increased focal uptake (FTU), increased irregular tracer uptake (ITU), and no tracer uptake (NTU). A numeric rating scale (NRS-11) assessed pain intensity. We analyzed the association between uptake patterns and treatment response using Pearson's chi-square test and Fisher's exact test. Uptake was quantified from SPECT/CT with region of interest (ROI) counting, and an intraclass correlation coefficient (ICC) calculated agreement. We used Student' t-test to calculate statistically significant differences of counts between groups and the Pearson correlation to measure the relationship between counts and initial NRS-1k1. Multivariate logistic regression analysis determined which variables were significantly associated with uptake. The FTU group included 32 patients; ITU, 39; and NTU, 24. With conservative management, 64 % of patients with increased tracer uptake (TU, both focal and irregular) and 36 % with NTU showed positive response. Conservative treatment response of FTU was better than NTU, but did not differ from that of ITU. Conservative treatment response of TU was significantly different from that of NTU (OR 3.1; p 0.036). Moderate positive correlation was observed between ITU and initial NRS-11. Age and initial NRS-11 significantly predicted uptake. Patients with uptake in their knee(s) on SPECT/CT showed positive treatment response under conservative treatment.

Removal of Escherichia coli and Faecal Coliforms from Surface Water and Groundwater by Household Water Treatment Devices/Systems: A Sustainable Solution for Improving Water Quality in Rural Communities of the Southern African Development Community Region

Directory of Open Access Journals (Sweden)

Jocelyne K. Mwabi

2012-01-01

Full Text Available There is significant evidence that household water treatment devices/systems (HWTS are capable of dramatically improving microbially contaminated water quality. The purpose of this study was to examine five filters [(biosand filter-standard (BSF-S; biosand filter-zeolite (BSF-Z; bucket filter (BF; ceramic candle filter (CCF; and silver-impregnated porous pot (SIPP] and evaluate their ability to improve the quality of drinking water at the household level. These HWTS were manufactured in the workshop of the Tshwane University of Technology and evaluated for efficiency to remove turbidity, faecal coliforms and Escherichia coli from multiple water source samples, using standard methods. The flow rates ranged from 0.05 L/h to 2.49 L/h for SIPP, 1 L/h to 4 L/h for CCF, 0.81 L/h to 6.84 L/h for BSF-S, 1.74 L/h to 19.2 L/h and 106.5 L/h to 160.5 L/h for BF The turbidity of the raw water samples ranged between 2.17 and 40.4 NTU. The average turbidity obtained after filtration ranged from 0.6 to 8 NTU (BSF-S, 1 to 4 NTU (BSF-Z, 2 to 11 NTU (BF, and from 0.6 to 7 NTU (CCF and 0.7 to 1 NTU for SIPP. The BSF-S, BSF-Z and CCF removed 2 to 4 log10 (99% to 100% of coliform bacteria, while the BF removed 1 to 3 log (90% to 99.9% of these bacteria. The performance of the SIPP in removing turbidity and indicator bacteria (>5 log10, 100% was significantly higher compared to that of the other HWTS (p < 0.05. The findings of this study indicate that the SIPP can be an effective and sustainable HWTS for the Southern African Development Community (SADC rural communities, as it removed the total concentration of bacteria from test water, can be manufactured using locally available materials, and is easy to operate and to maintain.

Unit thermal performance of atmospheric spray cooling systems

International Nuclear Information System (INIS)

Porter, R.W.; Jain, M.; Chaturvedi, S.K.

1980-01-01

Thermal performance of an open atmospheric spray pond or canal depends on the direct-contact evaporative cooling of an individual spray unit (spray nozzle or module) and the interference caused by local heating and humidification. Droplet parameters may be combined into a dimensionless group, number of transfer units (NTU) or equivalent, whereas large-scale air-vapor dynamics determine interference through the local wet-bulb temperature. Quantity NTU were implied from field experiments for a floating module used in steam-condenser spray canals. Previous data were available for a fixed-pipe nozzle assembly used in spray ponds. Quantity NTU were also predicted using the Ranz-Marshall correlations with the Sauter-mean diameter used as the characteristic length. Good agreement with experiments was shown for diameters of 1--1.1 cm (module) and 1.9 mm

Recovering low-turbidity cutting liquid from silicon slurry waste.

Science.gov (United States)

Tsai, Tzu-Hsuan; Shih, Yu-Pei

2014-04-30

In order to recover a low-turbidity polyalkylene glycol (PAG) liquid from silicon slurry waste by sedimentation, temperatures were adjusted, and acetone, ethanol or water was used as a diluent. The experimental results show that the particles in the waste would aggregate and settle readily by using water as a diluent. This is because particle surfaces had lower surface potential value and weaker steric stabilization in PAG-water than in PAG-ethanol or PAG-acetone solutions. Therefore, water is the suggested diluent for recovering a low-turbidity PAG (sedimentation. After 50 wt.% water-assisted sedimentation for 21 days, the solid content of the upper liquid reduced to 0.122 g/L, and the turbidity decreased to 44 NTU. The obtained upper liquid was then vacuum-distillated to remove water. The final recovered PAG with 0.37 NTU had similar viscosity and density to the unused PAG and could be reused in the cutting process. Copyright © 2014 Elsevier B.V. All rights reserved.

Wastewater renovation using constructed soil filter (CSF): a novel approach.

Science.gov (United States)

Nemade, P D; Kadam, A M; Shankar, H S

2009-10-30

Constructed soil filter (CSF) also known as Soil Biotechnology (SBT) is a process for water renovation which makes use of formulated media with culture of soil macro- and microorganisms. CSF combines sedimentation, infiltration and biodegradation processes to remove oxidizable organics and inorganics of wastewater in a single facility. Operating experience shows hydraulic loading in the range of 0.05-0.25 m(3)/m(2) h and organic loading up to 200-680 g/m(2) d. The results show increase in dissolved oxygen levels, COD removal (from 352 mg/l to 20 mg/l); BOD removal (from 211 mg/l to 7.0 mg/l); suspended solids removal (from 293 mg/l to 16 mg/l); turbidity reduction (from 145 NTU to 5.3 NTU); iron (from 5 mg/l to 0.3 mg/l); arsenic (from 500 microg/l to 10 microg/l); total coliform and fecal coliform removal (from 145 x 10(5) to 55 CFU/100 mL and 150 x 10(8) to 110 CFU/100 mL respectively), with desired pathogen levels as per WHO standards, i.e. aeration and no odor, fish compatible water quality and evergreen ambience.

Penyediaan Air Bersih Masyarakat Sekitar Masjid Al-Iklas Desa Cukanggenteng Ciwidey dengan Menggunakan Penyaringan Air Sederhana

Directory of Open Access Journals (Sweden)

Hans Kristianto

2017-12-01

Full Text Available Cukanggenteng Village, Ciwidey, Bandung has problem with availability of clean water. The villagers use water from Cisondari River near the village and shallow well which has high turbidity. Usage of high turbidity water could cause various health problems, such as cholera, dysentery, typhus, and so on. There is some effort done by the villager to reduce the water turbidity, by utilizing sedimentation process. However the sedimentation process does not work effectively. In this community service project, a sand filter and pipe filter was utilized to solve the clean water scarcity problem. The sand filter was operated up flow, and its overflow was fed into the pipe filter. The pipe filter consisted of three 4” pipes with sand, coconut shell carbon, and sponge. This system was designed with easily obtained filter media, and simple construction, so that it could be taken care, operated, duplicated by the villagers. Analysis of the water showed that the filtration could remove 91.06% of water turbidity from 94.55 NTU to 8.445 NTU, with pH 6.55. The water after this simple filtration process could be categorized as clean water, based on the standards in PERMENKES RI No. 416/MENKES/PER/IX/1990. The results obtained showed that the filtration process has successfully implemented to reduce the water turbidity.

Disturbed holistic processing in autism spectrum disorders verified by two cognitive tasks requiring perception of complex visual stimuli.

Science.gov (United States)

Nakahachi, Takayuki; Yamashita, Ko; Iwase, Masao; Ishigami, Wataru; Tanaka, Chitaru; Toyonaga, Koji; Maeda, Shizuyo; Hirotsune, Hideto; Tei, Yosyo; Yokoi, Koichi; Okajima, Shoji; Shimizu, Akira; Takeda, Masatoshi

2008-06-30

Central coherence is a key concept in research on autism spectrum disorders (ASD). It refers to the process in which diverse information is integrated and higher meaning is constructed in context. A malfunction in this process could result in abnormal attention to partial information in preference to the whole. To verify this hypothesis, we studied the performance of two visual tasks by 10 patients with autistic disorder or Asperger's disorder and by 26 (experiment 1) or 25 (experiment 2) normal subjects. In experiment 1, the subjects memorized pictures, some pictures with a change related to the main theme (D1) and others with a change not related to the main theme (D2); then the same pictures were randomly presented to the subjects who were asked to find the change. In experiment 2, the subjects were presented pictures of a normal (N) or a Thatcherized (T) face arranged side by side inversely (I) or uprightly (U) and to judge them as the same or different. In experiment 1, ASD subjects exhibited significantly lower rates of correct responses in D1 but not in D2. In experiment 2, ASD subjects exhibited significantly longer response times in NT-U but not in TN-I. These results showed a deficit in holistic processing, which is consistent with weak central coherence in ASD.

Treatment of Highly Turbid Water by Polyaluminum Ferric Chloride (PAFCL

Directory of Open Access Journals (Sweden)

Fazel Fazel Mohammadi-Moghaddam

2015-10-01

Full Text Available Background & Aims of the Study: In some situation like rainfall seasons raw water become very turbid so it affected the water treatment plant processes and quality of produced water. Treatment of very high turbid water has some concerns like precursors for disinfection by-products and very loading rate of particle on filter's media and consequently increases in water consumption for filter backwash. This paper investigates the performance of a composite inorganic polymer of aluminium and ferric salt, Polyaluminium ferric chloride (PAFCl, for the removal of turbidity, color and natural organic matter (NOM from high turbid water. Materials and Methods: Experiments were carried out by Jar test experiment by synthetic water samples with 250 and 500 NTU turbidity that prepared in laboratory. Results: The results of conventional jar test showed that the optimum pH for coagulation of water sample was 7.5 to 8 and optimum dosage of the coagulant was 10 mg/L. Removal efficiency of turbidity, color and UV adsorbent at 254 nm at optimum dose and pH without filtration was 99.92%, 100% and 80.6% respectively for first sample (250 NTU and 99.95%, 99.49% and 84.77 for second sample (500 NTU respectively. Conclusion: It concluded that polyaluminium ferric chloride has a very good efficiency for the removal of turbidity, color and organic matter in high turbid water. Also it can be select as a coagulant for high turbid water and some waste water from water treatment plant like filter backwash water.

Rapid removal of fine particles from mine water using sequential processes of coagulation and flocculation.

Science.gov (United States)

Jang, Min; Lee, Hyun-Ju; Shim, Yonsik

2010-04-01

The processes of coagulation and flocculation using high molecular weight long-chain polymers were applied to treat mine water having fine flocs of which about 93% of the total mass was less than 3.02 microm, representing the size distribution of fine particles. Six different combinations of acryl-type anionic flocculants and polyamine-type cationic coagulants were selected to conduct kinetic tests on turbidity removal in mine water. Optimization studies on the types and concentrations of the coagulant and flocculant showed that the highest rate of turbidity removal was obtained with 10 mg L(-1) FL-2949 (coagulant) and 12 mg L(-1) A333E (flocculant), which was about 14.4 and 866.7 times higher than that obtained with A333E alone and that obtained through natural precipitation by gravity, respectively. With this optimized condition, the turbidity of mine water was reduced to 0 NTU within 20 min. Zeta potential measurements were conducted to elucidate the removal mechanism of the fine particles, and they revealed that there was a strong linear relationship between the removal rate of each pair of coagulant and flocculant application and the zeta potential differences that were obtained by subtracting the zeta potential of flocculant-treated mine water from the zeta potential of coagulant-treated mine water. Accordingly, through an optimization process, coagulation-flocculation by use of polymers could be advantageous to mine water treatment, because the process rapidly removes fine particles in mine water and only requires a small-scale plant for set-up purposes owing to the short retention time in the process.

Researcher might have found answer to 'birth of the universe'

CERN Multimedia

2003-01-01

A National Taiwan University (NTU) research team has discovered a new physical phenomenon that could challenge the well-accepted theory about the birth of the universe. However,Lee Shih-chang, a researcher at Academia Sinica's Institute of Physics, said the new scientific research results will be accepted only after an academic paper detailing the research process and conclusions is released and the research results are verified by experts in the field.

Evaluation of the RSG-GAS cooling tower performance

International Nuclear Information System (INIS)

Suroso

2003-01-01

Utilization of RSG-GAS reactor should be operated as efficiently as possible, so that reactor operation planning using one line primary coolant can be anticipated. To analyze the performance of the RSG-GAS cooling tower with one line primary coolant doing by using same data from 10 MW thermal reactor operation. The result were then compare to those achieved using CATHENA code. The results indicated that, for design condition the ratio of water flowrate to air is (L/G) 1.52 and number transfer unit (NTU) is 0.348. For operation condition, the average of L/G and NTU are respectively 1.37 and 0,348. Moreover the results achieved by the code showed that L/G and NTU are respectively 1.35 and 0,302. The performance of cooling tower achieved operation condition and the code results are respectively 91% and 72%. This means that the calculated results are lower than measurement results

Reduction of Turbidity of Water Using Locally Available Natural Coagulants

Science.gov (United States)

Asrafuzzaman, Md.; Fakhruddin, A. N. M.; Hossain, Md. Alamgir

2011-01-01

Turbidity imparts a great problem in water treatment. Moringa oleifera, Cicer arietinum, and Dolichos lablab were used as locally available natural coagulants in this study to reduce turbidity of synthetic water. The tests were carried out, using artificial turbid water with conventional jar test apparatus. Optimum mixing intensity and duration were determined. After dosing water-soluble extracts of Moringa oleifera, Cicer arietinum, and Dolichos lablab reduced turbidity to 5.9, 3.9, and 11.1 nephelometric turbidity unit (NTU), respectively, from 100 NTU and 5, 3.3, and 9.5, NTU, respectively, after dosing and filtration. Natural coagulants worked better with high, turbid, water compare to medium, or low, turbid, water. Highest turbidity reduction efficiency (95.89%) was found with Cicer arietinum. About 89 to 96% total coliform reduction were also found with natural coagulant treatment of turbid water. Using locally available natural coagulants, suitable, easier, and environment friendly options for water treatment were observed. PMID:23724307

Preparation, characterization, and application of Ti/TiO2-NTs/Sb-SnO2 electrode in photo-electrochemical treatment of industrial effluents under mild conditions.

Science.gov (United States)

Subba Rao, Anantha N; Venkatarangaiah, Venkatesha T

2018-04-01

Ti/TiO 2 -NTs/Sb-SnO 2 electrode was prepared by gradient pulsed electrodeposition, and its electrochemical properties were evaluated. The catalytic activity and reusability of the electrode were tested by electrochemical oxidation (EO) and photoelectrochemical oxidation (PEO) of organics present in textile industry wastewater (TWW) and coffee bean processing industry wastewater (CWW). COD removal of ~ 41% was achieved after 5-h electrolysis under a constant applied current density of 30 mA cm -2 for TWW and 50 mA cm -2 for CWW. Nearly 14 and 18% increment in COD removal was observed under PEO for TWW and CWW, respectively. The turbidity of TWW reduced from 15 to ~ 3 NTU and the turbidity of CWW reduced from 27 to ~ 3 NTU by both EO and PEO. The % COD removal observed after 5-h electrolysis remained consistent for 7 repeated cycles; however, the catalytic activity of the electrode reduced gradually. These results suggested that the Ti/TiO 2 -NTs/Sb-SnO 2 can be a potential electrode for the treatment of industrial wastewater.

Removal of fluoride, SDS, ammonia and turbidity from semiconductor wastewater by combined electrocoagulation-electroflotation.

Science.gov (United States)

Aoudj, S; Khelifa, A; Drouiche, N

2017-08-01

Semiconductor industry effluents contain organic and inorganic pollutants, such as sodium dodecyl sulfate (SDS), fluoride and ammonia, at high levels which consists a major environmental issue. A combined EC-EF process is proposed as a post-treatment after precipitation for simultaneous clarification and removal of pollutants. In EC step, a hybrid Fe-Al was used as the soluble anode in order to avoid supplementary EC step. EC-Fe is more suitable for SDS removal; EC-Al is more suitable for fluoride removal, while EC with hybrid Al-Fe makes a good compromise. Clarification and ammonia oxidation were achieved in the EF step. Effects of anodic material, initial pH, current, anion nature, chloride concentration and initial pollutant concentration were studied. The final concentrations may reach 0.27, 6.23 and 0.22 mg L -1 for SDS, fluoride and ammonia respectively. These concentrations are far lower than the correspondent discharge limits. Similarly, the final turbidity was found 4.35 NTU which is lower than 5NTU and the treated water does not need further filtration before discharge. Furthermore, the EC-EF process proves to be sufficiently energy-efficient with less soluble electrode consumption. Copyright © 2017 Elsevier Ltd. All rights reserved.

Operating Conditions of Coagulation-Flocculation Process for High Turbidity Ceramic Wastewater

Directory of Open Access Journals (Sweden)

Sameer Al-Asheh

2017-04-01

Full Text Available This work attempted to determine the optimum conditions required for the coagulation and flocculation process as an essential stage of the ceramic wastewater treatment. Coagulation and flocculation is a very necessary step in industries as it lessens turbidity, color, and odor of wastewater. The experimental work was performed in several runs. The volume of wastewater used in each run was 200 mL and was kept at this value throughout. In certain runs, the speed of the mixer was varied while keeping the quantity of coagulant and flocculant constant in order to determine the optimum speed that resulted in the least turbidity. A speed of 5% was chosen as the ideal process speed according to the results obtained. Next, experiments were operated at this optimum speed while changing the dosage of coagulant and flocculant in order to decide the optimum dosage. Coagulant and flocculent amounts of 0.4 g (without booster and 0.2 g (with booster selected after the readings were taken. For all the readings, a turbidity meter was used providing results in Nephelometric Turbidity Units (NTU. Lowest turbidity was achieved when using 5% speed with 0.4 grams of coagulant and 0.4 grams of flocculant, or 5% speed with 0.2 grams of coagulant, 0.2 grams of flocculant and 0.25 g/L of booster coagulant. According to factorial design analysis, such as parameters as impeller speed and dosage have an influential impact on the turbidity; while the booster has insignificant influence and other interactions between parameters are important.

Performance Evaluation of Five Turbidity Sensors in Three Primary Standards

Science.gov (United States)

Snazelle, Teri T.

2015-10-28

Open-File Report 2015-1172 is temporarily unavailable.Five commercially available turbidity sensors were evaluated by the U.S. Geological Survey, Hydrologic Instrumentation Facility (HIF) for accuracy and precision in three types of turbidity standards; formazin, StablCal, and AMCO Clear (AMCO–AEPA). The U.S. Environmental Protection Agency (EPA) recognizes all three turbidity standards as primary standards, meaning they are acceptable for reporting purposes. The Forrest Technology Systems (FTS) DTS-12, the Hach SOLITAX sc, the Xylem EXO turbidity sensor, the Yellow Springs Instrument (YSI) 6136 turbidity sensor, and the Hydrolab Series 5 self-cleaning turbidity sensor were evaluated to determine if turbidity measurements in the three primary standards are comparable to each other, and to ascertain if the primary standards are truly interchangeable. A formazin 4000 nephelometric turbidity unit (NTU) stock was purchased and dilutions of 40, 100, 400, 800, and 1000 NTU were made fresh the day of testing. StablCal and AMCO Clear (for Hach 2100N) standards with corresponding concentrations were also purchased for the evaluation. Sensor performance was not evaluated in turbidity levels less than 40 NTU due to the unavailability of polymer-bead turbidity standards rated for general use. The percent error was calculated as the true (not absolute) difference between the measured turbidity and the standard value, divided by the standard value.The sensors that demonstrated the best overall performance in the evaluation were the Hach SOLITAX and the Hydrolab Series 5 turbidity sensor when the operating range (0.001–4000 NTU for the SOLITAX and 0.1–3000 NTU for the Hydrolab) was considered in addition to sensor accuracy and precision. The average percent error in the three standards was 3.80 percent for the SOLITAX and -4.46 percent for the Hydrolab. The DTS-12 also demonstrated good accuracy with an average percent error of 2.02 percent and a maximum relative standard

Rapid removal of fine particles from mine water using sequential processes of coagulation and flocculation

Energy Technology Data Exchange (ETDEWEB)

Jang, M.; Lee, H.J.; Shim, Y. [Korean Mine Reclamation Corporation MIRECO, Seoul (Republic of Korea)

2010-07-01

The processes of coagulation and flocculation using high molecular weight long-chain polymers were applied to treat mine water having fine flocs of which about 93% of the total mass was less than 3.02 {mu} m, representing the size distribution of fine particles. Six different combinations of acryl-type anionic flocculants and polyamine-type cationic coagulants were selected to conduct kinetic tests on turbidity removal in mine water. Optimization studies on the types and concentrations of the coagulant and flocculant showed that the highest rate of turbidity removal was obtained with 10 mg L{sup -1} FL-2949 (coagulant) and 12 mg L{sup -1} A333E (flocculant), which was about 14.4 and 866.7 times higher than that obtained with A333E alone and that obtained through natural precipitation by gravity, respectively. With this optimized condition, the turbidity of mine water was reduced to 0 NTU within 20 min. Zeta potential measurements were conducted to elucidate the removal mechanism of the fine particles, and they revealed that there was a strong linear relationship between the removal rate of each pair of coagulant and flocculant application and the zeta potential differences that were obtained by subtracting the zeta potential of flocculant-treated mine water from the zeta potential of coagulant-treated mine water. Accordingly, through an optimization process, coagulation-flocculation by use of polymers could be advantageous to mine water treatment, because the process rapidly removes fine particles in mine water and only requires a small-scale plant for set-up purposes owing to the short retention time in the process.

Electrocoagulation (EC and Electrocoagulation/Flotation(ECF Processes for Removing High Turbidity from Surface Water Using Al and Fe Electrodes

Directory of Open Access Journals (Sweden)

Ghorban Asgari

2013-08-01

Full Text Available Electrocoagulation (EC and Electrocoagulation/flotation (ECF processes are simple and efficient in water and wastewater treatment. In recent years, many investigations have focused on the use of these processes for treating of polluted water. The purpose of this study was to investigate the efficiency of EC and ECF processes in removal of high turbidity water using different electrodes in different circumstances. In present study an electrocoagulation and electrocoagulation/ flotation reactor in a lab scale to an approximate volume of 6 liters which is equipped with four Al-AL and Fe-Fe electrodes (200 * 20 * 2 mm was used  for removing of high turbidity water. The effects of operating parameters such as type of electrodes, initial water turbidity, applied voltage (10 to 30 v, initial pH of the solution (3 to 12 and reaction times (5 to 30 minutes were evaluated. The batch experimental results showed that initial turbidity water, initial pH of the solution, different applied voltages up to %88 turbidity as initial turbidity of 1200 NTU have been removed when using Al-Al and Fe-Fe electrodes and reaction times highly effective on the turbidity removal efficiency in these processes. In ECF process, 84% in optimum condition. However, in EC  process the maximum removal was found  up to 68% of initial turbidity when using Al-Al and Fe-Fe electrodes in same operation. Based on the result obtained in this study, the type of electrodes in EC and ECF processes  significantly affect the removal rate of high turbid water. Also, it was found that much higher turbidity removal could be achieved by ECF process than that by EC process in the same condition.

Optimization of culture condition for ACEI and GABA production by lactic acid bacteria.

Science.gov (United States)

Tung, Yi-Ting; Lee, Bao-Hong; Liu, Chin-Feng; Pan, Tzu-Ming

2011-01-01

Gamma-aminobutyric acid (GABA) and angiotensin-converting enzyme inhibitor (ACEI) are compounds which can influence hypertension. The goal of this study is to optimize the culture condition for GABA and ACEI production by Lactobacillus plantarum NTU 102 fermented skim milk. In this study, we used 3-factor-3-level Box-Behnken design combining with response surface methodology, where the 3 factors represent the concentration of skim milk, the concentration of monosodium glutamate, and culture temperature. Best conditions for GABA and ACEI production differed. The results indicated that L. plantarum NTU 102 produced the highest combined levels of GABA and ACEI at 37 °C, in milk having 8% to 12% nonfat solids supplemented with 0.6% to 1% MSG. Agitation of the medium during fermentation had no effect on GABA or ACEI production but extended incubation (up to 6 d) increases levels of the bioactive compounds. L. plantarum NTU 102 fermented products may be a potential functional food source for regulating hypertension. © 2011 Institute of Food Technologists®

Assessing the risk posed by high-turbidity water to water supplies.

Science.gov (United States)

Chang, Chia-Ling; Liao, Chung-Sheng

2012-05-01

The objective of this study is to assess the risk of insufficient water supply posed by high-turbidity water. Several phenomena can pose risks to the sufficiency of a water supply; this study concerns risks to water treatment plants from particular properties of rainfall and raw water turbidity. High-turbidity water can impede water treatment plant operations; rainfall properties can influence the degree of soil erosion. Thus, water turbidity relates to rainfall characteristics. Exceedance probabilities are presented for different rainfall intensities and turbidities of water. When the turbidity of raw water is higher than 5,000 NTU, it can cause operational problems for a water treatment plant. Calculations show that the turbidity of raw water at the Ban-Sin water treatment plant will be higher than 5,000 NTU if the rainfall intensity is larger than 165 mm/day. The exceedance probability of high turbidity (turbidity >5,000 NTU) in the Ban-Sin water treatment plant is larger than 10%. When any water treatment plant cannot work regularly, its ability to supply water to its customers is at risk.

Design and Application of Electrochemical Processes for Decolorization Treatment of Nylanthrene Red dye Bearing Wastewaters

Directory of Open Access Journals (Sweden)

D. Marmanis

2016-04-01

Full Text Available The purpose of this paper is the investigation of the capability of electrochemical methods, such as electrocoagulation, electrooxidation and electro-Fenton for decolorization and degradation of synthetic aqueous solutions and actual dye house effluents containing nylanthrene red reactive dye. All electrochemical experiments with the synthetic dye solutions were conducted in electrochemical cell of volume 500 ml containing 200 mL of dye solution at concentration 50 mg/L and interelectrode distance of 1 cm. The three different electrochemical processes were analyzed, and their removal efficiencies were measured and evaluated. In addition, a flow diagram is designed for a continuously operated electrochemical process for remediation of synthetic and actual dye house effluents laden with nylanthrene dye. In the electrocoagulation process with aluminum electrodes, the colored aqueous dye solution was treated at the applied current densities of 5, 10 and 15 mA/cm2 and was quantitatively decolorized in 11, 9 and less than 6 minutes of electroprocessing time respectively. The electrooxidation process conducted with Ti/Pt and boron doped diamond (BDD electrodes, at the applied current density of 10 mA/cm2 led to the quantitative decolorization and destruction of the dye in 25 and 15 min respectively. In the electro-Fenton process with iron electrodes, supply of added hydrogen peroxide and applied current density of 10 mA/cm2, complete decolorization and degradation of the nylanthrene red dye occurred in 6 min. The actual polyamide textile dyeing effluent of same volume 200 mL with initial turbidity of 114 NTU and COD of 1755 mg/L was treated by electrocoagulation at the same applied current density of 10 mA/cm2. The turbidity was quantitatively eliminated in only 10 min, while COD was reduced by 74.5 % in 40 minutes of electrolysis time.

ABOUT SYSTEM OF DISTANCE LEARNING IN OPEN ONLINE COURSE

Directory of Open Access Journals (Sweden)

V.М. Kukharenko

2012-03-01

Full Text Available This paper describes the first part of the open online course "E-Learning from A to Z", dedicated to the creation and development of system of distance learning (university or corporation. The results of the learning process and discussion on the workshop at NTU "KPI" in 2012 is shown the interest of teachers in a new form of online course and lack of development of personal learning environment. The open online courses can contribute to society practice.

DynaGuard: Armoring Canary-Based Protections against Brute-Force Attacks

Science.gov (United States)

2015-12-11

format of the canary check or a function’s prologue and epilogue. Finally, due to the small number of canary-protected frames that (on average) are...sje ng 462 .lib qua ntu m 464 .h2 64r ef 471 .om net pp 473 .as tar 483 .xa lan cbm k Apa che Ng inx Pos tgre SQ L SQ Lite My SQ L Sl ow do w n (n...k 456 .hm me r 458 .sje ng 462 .lib qua ntu m 464 .h2 64r ef 471 .om net pp 473 .as tar 483 .xa lan cbm k Apa che Ng inx

A Simple Slow-Sand Filter for Drinking Water Purification

Directory of Open Access Journals (Sweden)

K. O. Yusuf

2017-04-01

Full Text Available Water-borne diseases are commonly encountered when pathogen-contaminated water is consumed. In rural areas, water is usually obtained from ponds, open shallow wells, streams and rain water during rainy season. Rain water is often contaminated by pathogens due to unhygienic of physical and chemical conditions of the roofs thereby making it unsafe for consumption. A simple slow sand filter mechanism was designed and fabricated for purification of water in rural areas where electricity is not available to power water purification devices. Rain water samples were collected from aluminum roof, galvanized roof and thatched roof. The waters samples were allowed to flow through the slow sand filter. The values of turbidity, total dissolved solids, calcium, nitrite, faecal coliform and total coliform from unfiltered water through thatched roof were 0.92 NTU, 27.23 mg/l, 6 mg/l, 0.16 mg/l, 5cfu/100ml and 6.0 cfu/100ml, respectively while the corresponding values for slow sand filter from thatched roof were 0.01 NTU, 0.23 mg/l, 2.5 mg/l, 0.1 mg/l, 0 cfu/100ml and 0 cfu/100ml, respectively. The values of turbidity, total dissolved solid, nitrite, calcium, faecal coliform and total coliform from unfiltered water for aluminum roof were 0.82 NTU, 23.68 mg/l, 2.70 mg/l, 1.0 mg/l, 4 cfu/100ml and 4cfu/100ml, respectively while the corresponding values for slow sand filter were 0.01 NTU, 0.16 mg/l, 0.57 mg/l, 0.2 mg/l, 0 cfu/100ml and 0 cfu/100ml, respectively. The values obtained for galvanized roof were also satisfactory. The slow sand filter is recommended for used in rural areas for water purification to prevent risk of water-borne diseases.

Examination Of The Physicochemical Characteristics Of Domestic Water Sources In Ebonyi Local Government Area Of Ebonyi State Nigeria.

Directory of Open Access Journals (Sweden)

Nwidembia

2015-08-01

Full Text Available Lack of good drinking water due to contamination by chemicals has been a global menace. It is one of the most serious environmental problems that have greatly impacted human health. Basic quality parameters of domestic water sources in Ebonyi Local Government Area were studied in the months of September 2014 and October 2014. Samples were randomly collected from common water sources well stream borehole and pond across four communities in the Local Government Area. The physicochemical characteristics of the collected water samples were investigated using standard procedures. The results showed mean pH values of 7.3 7.8 6.8 and 7.0 for well stream borehole and pond water samples respectively. The colour examination showed 13 HU 11 HU 13 HU and 16 HU for well stream borehole and pond water samples respectively. The turbidity were recorded as 103 NTU well 90 NTU stream 0.8 NTU borehole and 92 NTU pond. Total dissolved solids TDS showed a record of 595 mgL 386mgL 76 mgL and 563 mgL for well stream borehole and pond respectively. Well water recorded 78 mgL stream 112 mgL borehole 42 mgL and pond 795 mgL for Total Suspended Solids respectively. Also the total hardness showed 525 mgL 779 mgL 44 mgL and 837 mgL for well stream borehole and pond water samples respectively. The results show that most of the common sources of water in the studied areas are not good for drinking since the physicochemical variables evaluated mostly exceeded WHO permissible limits. We therefore recommend that water treatment should be paramount as alternative sources of drinking water in the communities should be considered.

Monitoring of event-based mobilization of hydrophobic pollutants in rivers: calibration of turbidity as a proxy for particle facilitated transport in field and laboratory.

Science.gov (United States)

Rügner, Hermann; Schwientek, Marc; Egner, Marius; Grathwohl, Peter

2014-08-15

Transport of many pollutants in rivers is coupled to mobilization of suspended particles which typically occurs during floods. Since the amount of total suspended solids (TSS) in rivers can be monitored by turbidity measurements this may be used as a proxy for the total concentration of particle associated pollutants such as PAHs, PCBs, etc. and several heavy metals. Online turbidity measurements (e.g. by optical backscattering sensors) would then also allow for an assessment of particle and pollutant flux dynamics if once calibrated against TSS and total pollutant concentrations for a given catchment. In this study, distinct flood and thus turbidity events were sampled at high temporal resolution in three contrasting sub-catchments of the River Neckar in Southwest Germany (Ammer, Goldersbach, Steinlach) as well as in the River Neckar itself and investigated for the total amount of PAHs and TSS in water; turbidity (NTU) and grain size distributions of suspended solids were determined as well. Laboratory experiments were performed with natural river bed sediments from different locations (Ammer) to investigate PAH concentrations, TSS and turbidity during sedimentation of suspended particles under controlled conditions (yielding smaller and smaller suspended particles and TSS with time). Laboratory and field results agreed very well and showed that turbidity and TSS were linearly correlated over an extended turbidity range up to 2000 NTU for the field samples and up to 8000 NTU in lab experiments. This also holds for total PAH concentrations which can be reasonably well predicted based on turbidity measurements and TSS vs. PAHs relationships - even for high turbidity values observed during flood events (>2000 NTU). Total PAH concentrations on suspended solids were independent of grain size of suspended particles. This implies that for the rivers investigated the sorption capacity of particles did not change significantly during the observed events. Copyright © 2014

The synergetic effects of turbulence and turbidity on the zooplankton community structure in large, shallow Lake Taihu.

Science.gov (United States)

Zhou, Jian; Qin, Boqiang; Han, Xiaoxia

2018-01-01

Climate change is predicted to influence the heat budget of aquatic ecosystems and, in turn, affect the stability of the water column leading to increased turbulence coupled with enhanced turbidity. However, the synergetic effects of turbulence and turbidity on zooplankton community structure remain to be understood in large, shallow lakes. To determine the possible synergetic effects of these factors on zooplankton communities, a 15-day mesocosm experiment was carried out and tested under four turbulence and turbidity regimes namely control (ɛ = 0, 7.6 ± 4.2 NTU), low (ɛ = 6.01 × 10 -8  m 2  s -3 , 19.4 ± 8.6 NTU), medium (ɛ = 2.95 × 10 -5  m 2  s -3 , 55.2 ± 14.4 NTU), and high (ɛ = 2.39 × 10 -4  m 2  s -3 , 741.6 ± 105.2 NTU) conditions, which were comparable to the natural conditions in Lake Taihu. Results clearly showed the negative effects of turbulence and turbidity on zooplankton survival, which also differed among taxa. Specifically, increased turbulence and turbidity levels influenced the competition among zooplankton species, which resulted to the shift from being large body crustacean-dominated (copepods and cladocerans) to rotifer-dominated community after 3 days. The shift could be associated with the decrease in vulnerability of crustaceans in such environments. Our findings suggested that changes in the level of both turbidity and turbulence in natural aquatic systems would have significant repercussions on the zooplankton communities, which could contribute to the better understanding of community and food web dynamics in lake ecosystems exposed to natural mixing/disturbances.

Development of a Low Cost Earthquake Early Warning System in Taiwan

Science.gov (United States)

Wu, Y. M.

2017-12-01

The National Taiwan University (NTU) developed an earthquake early warning (EEW) system for research purposes using low-cost accelerometers (P-Alert) since 2010. As of 2017, a total of 650 stations have been deployed and configured. The NTU system can provide earthquake information within 15 s of an earthquake occurrence. Thus, this system may provide early warnings for cities located more than 50 km from the epicenter. Additionally, the NTU system also has an onsite alert function that triggers a warning for incoming P-waves greater than a certain magnitude threshold, thus providing a 2-3 s lead time before peak ground acceleration (PGA) for regions close to an epicenter. Detailed shaking maps are produced by the NTU system within one or two minutes after an earthquake. Recently, a new module named ShakeAlarm has been developed. Equipped with real-time acceleration signals and the time-dependent anisotropic attenuation relationship of the PGA, ShakingAlarm can provide an accurate PGA estimation immediately before the arrival of the observed PGA. This unique advantage produces sufficient lead time for hazard assessment and emergency response, which is unavailable for traditional shakemap, which are based on only the PGA observed in real time. The performance of ShakingAlarm was tested with six M > 5.5 inland earthquakes from 2013 to 2016. Taking the 2016 M6.4 Meinong earthquake simulation as an example, the predicted PGA converges to a stable value and produces a predicted shake map and an isocontour map of the predicted PGA within 16 seconds of earthquake occurrence. Compared with traditional regional EEW system, ShakingAlarm can effectively identify possible damage regions and provide valuable early warning information (magnitude and PGA) for risk mitigation.

Dicty_cDB: Contig-U10467-1 [Dicty_cDB

Lifescience Database Archive (English)

Full Text Available ments: (bits) Value N ( BJ433957 ) Dictyostelium discoideum cDNA clone:ddv23p10, 3' ... 1084 0.0 2 ( EU868611 ) Human enterovirus...73 ) Xenopus tropicalis cDNA clone MGC:172876 IMAGE:76... 44 7.1 1 ( EF063152 ) Human enterovirus... 71 strain E2005125-TW polyprote... 44 7.1 1 ( DQ868521 ) Human enterovirus 71 isolate E2006...249-TW VP1 stru... 44 7.1 1 ( DQ846663 ) Human enterovirus 71 isolate NTU1551-TW-06 VP1 st... 44 7.1 1 ( DQ846662 ) Human enterovirus... 71 isolate NTU1482-TW-06 VP1 st... 44 7.1 1 ( DQ841970 ) Human enterovirus 71 isol

Study on an integrated process combining ozonation with ceramic ultra-filtration for decentralized supply of drinking water.

Science.gov (United States)

Zhu, Jia; Fan, Xiao J; Tao, Yi; Wei, De Q; Zhang, Xi H

2014-09-19

An integrated process was specifically developed for the decentralized supply of drinking water from micro-polluted surface water in the rural areas of China. The treatment process combined ozonation with ceramic ultra-filtration (UF), coagulation for pre-treatment and granular activated carbon filtration. A flat-sheet ceramic membrane was used with a cut-off of 60 nm and the measurement of 254 mm (length) × 240 mm (width) × 6 mm (thickness). Ozonation and ceramic UF was set up whthin one reactor. The experimental results showed that the removal efficiencies of the dissolved organic carbon (DOC) and the formation potential of trihalomethanes (THMs), haloacetic acids (HAAs) and ammonia were 80%, 76%, 70% and 90%, respectively; that the turbidity of the product water was below 0.2 NTU and the particle count number (particles larger than 2 μm) was less than 50 counts per mL. The result also showed that all the pathogenic microorganisms were retained by the ceramic and that UF. Ozonation played a critical role in the control of membrane fouling and the removal of contaminants. Exactly, the membrane fouling can be controlled in situ with 3 mg L(-1) ozone at the permeate flux of 80 L m(-2) h(-1), yet the required dosage of ozone was dependent on the quality of the raw water. Therefore, this study is able to provide a highly compacted system for decentralized supply of high-quality drinking water in terms of both chemical and microbiological safety for the rural areas in China.

Performance of alum and assorted coagulants in turbidity removal of muddy water

Science.gov (United States)

Malik, Qasim H.

2018-03-01

Coagulation is a primary and cost effective process in water treatment plants. Under optimum conditions, not only it effectively removes turbidity but also results in reduced sludge volume and subsequently minimizes sludge management costs. Highly turbid water from streams, canals, rivers and rain run offs was run through jar test for turbidity removal. The brown water with 250NTU turbidity when coagulated with alum and assorted coagulants proved that maximum turbidity removal was witnessed using alum dose of 0.25 g/l at ph 6 with a sedimentation time of 30 min.

Turbidity and chlorine demand reduction using alum and moringa flocculation before household chlorination in developing countries.

Science.gov (United States)

Preston, Kelsey; Lantagne, Daniele; Kotlarz, Nadine; Jellison, Kristen

2010-03-01

Over 1.1 billion people in the world lack access to improved drinking water. Diarrhoeal and other waterborne diseases cause an estimated 1.87 million deaths per year. The Safe Water System (SWS) is a household water treatment intervention that reduces diarrhoeal disease incidence among users in developing countries. Turbid waters pose a particular challenge to implementation of SWS programmes; although research shows that a 3.75 mg l(-1) sodium hypochlorite dose effectively treats turbid waters, users sometimes object to the strong chlorine taste and prefer to drink water that is more aesthetically pleasing. This study investigated the efficacy of two locally available chemical water treatments-alum and Moringa oleifera flocculation-to reduce turbidity and chlorine demand at turbidities of 10, 30, 70, 100 and 300 NTU. Both treatments effectively reduced turbidity (alum flocculation 23.0-91.4%; moringa flocculation 14.2-96.2%). Alum flocculation effectively reduced chlorine demand compared with controls at 30, 70, 100 and 300 NTU (p=0.01-0.06). Moringa flocculation increased chlorine demand to the point where adequate free chlorine residual was not maintained for 24 hours after treatment. Alum pretreatment is recommended in waters>or=30 NTU for optimum water disinfection. Moringa flocculation is not recommended before chlorination.

Heat transfer characteristics of a helical heat exchanger

International Nuclear Information System (INIS)

San, Jung-Yang; Hsu, Chih-Hsiang; Chen, Shih-Hao

2012-01-01

Heat transfer performance of a helical heat exchanger was investigated. The heat exchanger is composed of a helical tube with rectangular cross section and two cover plates. The ε–Ntu relation of the heat exchanger was obtained using a numerical method. In the analysis, the flow in the tube (helical flow) was considered to be mixed and the flow outside the tube (radial flow) was unmixed. In the experiment, the Darcy friction factor (f) and convective heat transfer coefficient (h) of the radial flow were measured. The radial flow was air and the helical flow was water. Four different channel spacing (0.5, 0.8, 1.2 and 1.6 mm) were individually considered. The Reynolds numbers were in the range 307–2547. Two correlations, one for the Darcy friction factor and the other for the Nusselt number, were proposed. - Highlights: ► We analyze the heat transfer characteristics of a helical heat exchanger and examine the effectiveness–Ntu relation. ► Increasing number of turns of the heat exchanger would slightly increase the effectiveness. ► There is an optimum Ntu value corresponding to a maximum effectiveness. ► We measure the Darcy friction factor and Nusselt number of the radial flow and examine the correlations.

Variables in the process of coagulation / flocculation / settling of leachate of municipal landfills

Directory of Open Access Journals (Sweden)

José Fernando Thomé Jucá

2012-08-01

Full Text Available The careless disposal of waste may generate tremendous environmental and social impacts. For the treatment of landfill leachate, biological and physic-chemical treatments are routinely used. Chemical precipitation using calcium hydroxide has been used with great effectiveness in treating effluent with high concentrations of organic compounds and heavy metals. The leachate used in this study was collected from a flow box of the Muribeca landfill, located in the city of Jaboatão Guararapes, PE. Commercial calcium hydroxide was used as coagulant in aqueous solution. The experiment was implemented using a fractional factorial design, followed by a complete planning 24. It was observed that the lowest turbidity and color were obtained at the highest flocculation speeds. Color removal was favored by long flocculation time whereas this did not occur for turbidity removal. For the optimal point, a reduction of 52% of the color and a NTU turbidity within the standards established in Brazilian Laws (CONAMA 357/05 and CONAMA 430/11 were obtained.

10 kohta veel all / Kaido Haagen

Index Scriptorium Estoniae

Haagen, Kaido

2014-01-01

Sukeldumiskohti maailmas: Similani saared Tais, Averoy Norras, Tofo Mosambiigis, Punane meri Egiptuses, Sipadani saar Malaisias, Dili Ida-Timoris, Tulamben Balil, Lembeh Indoneesias, Malapascua Filipiinidel, Äntu järved Eestis

Flocculation of retention pond water

International Nuclear Information System (INIS)

Hart, B.T.; McGregor, R.J.

1982-05-01

An integral part of the water management strategy proposed by Ranger Uranium Mining Pty. Ltd. involves the collection of runoff water in a series of retention ponds. This water will subsequently be used in the uranium milling plant or released to Magela Creek. Runoff water collected during the wet season caused a section of Magela Creek to become turbid when it was released. The eroded material causing the turbidity was very highly dispersed and showed little tendency to sediment out in the retention ponds. Results of a preliminary study to determine the feasibility of clarifying retention pond water by flocculation with alum are presented. A concentration of 30 Mg/L alum reduced turbidity from an initial 340 NTU to less than 30 NTU in four hours

Experimental studies on hydrogen isotopic deuterium from gas to liquid phase by catalytic exchange

International Nuclear Information System (INIS)

Luo Yangming; Wang Heyi; Liu Jun; Fu Zhonghua; Wang Changbin; Han Jun; Xia Xiulong; Tang Lei

2005-01-01

The experimental studies on hydrogen isotopic deuterium from gas to liquid phase were completed by mixed ratio 1:4 of Pt-SDB hydrophobic catalyst and hydrophilic packing. The influencing factors on number of transfer units (NTU) and transformation efficiencies of deuterium were researched. The results show that preferable NTU can be obtained by choosing suitable operational temperature and flux of exchange gas. The transformation rate increases with increasing liquid flux, but it cannot obviously be improved when liquid flux attains some level. The length of catalytic column has an obvious influence on transformation rate and 90% of transformation rate is obtained by 4 m column length at gas flux with 2 m 3 /h, liquid flux with 1-2 kg/h and 45 degree C. (author)

The consequences of tourism for a fisherman’s family in Sfântu Gheorghe, the Danube Delta

Directory of Open Access Journals (Sweden)

IVAN Oana

2012-09-01

Full Text Available This paper examines the operation of a guesthouse owned by a local fisherman in Sfantu Gheorghe, a village in Romania’s Danube Delta. In the context of the regional expansion of tourism, it sheds light on how a local family adapts to new economic conditions. The local family’s life revolves around tourism during the peak season, andunlike other tourist destinations, the members of the family, are the first to benefit from this business. Adopting an anthropological perspective, I examine the role played by each member in this family business to demonstrate how household roles and social relations have been both transformed and maintained in the process of adopting new economic activities to take advantage of emerging opportunities to further household goals of production and reproduction. Even though tourism seems to be an important source of income, this type of activity is close connected to the main subsistence strategy, which is fishing. Furthermore, the tourist season only lasts for two months and so does this particularly work division and organization in the family. Employing participant observation and interview as main research methods, this study looks at how tourism is affecting the local culture, paying particular attention to gender, language, kinship, and work division.

A comparison between Moringa oleifera and chemical coagulants in the purification of drinking water - An alternative sustainable solution for developing countries

Science.gov (United States)

Pritchard, M.; Craven, T.; Mkandawire, T.; Edmondson, A. S.; O'Neill, J. G.

A research project was commissioned to investigate the performance of Moringa oleifera compared with that of aluminium sulphate (Al 2(SO 4) 3) and ferric sulphate (Fe 2(SO 4) 3), termed alum and ferric respectively. A series of jar tests was undertaken using model water, different raw water sources and hybrid water containing a mixture of both of these types of water. The model water consisted of deionised water spiked with Escherichia coli (E. coli) at 10 4 per 100 ml and turbidity (146 NTU) artificially created by kaolin. Results showed that M. oleifera removed 84% turbidity and 88% E. coli, whereas alum removed greater than 99% turbidity and E. coli. Low turbidity river water (<5 NTU), with an E. coli count of 605 colony forming units (cfu)/100 ml was treated with M. oleifera and ferric. Results showed an 82% and 94% reduction in E. coli for M. oleifera and ferric respectively. Tests on turbid river water of 45 NTU, with an E. coli count of 2650 cfu/100 ml, showed a removal of turbidity of 76% and E. coli reduction of 93% with M. oleifera. The equivalent reductions for alum were 91% and 98% respectively. Highly coloured reservoir water was also spiked with E. coli (10 4 cfu/100 ml) and turbidity (160 NTU) artificially created by kaolin; termed hybrid water. Under these conditions M. oleifera removed 83% colour, 97% turbidity and reduced E. coli by 66%. Corresponding removal values for alum were 88% colour, 99% turbidity and 89% E. coli, and for ferric were 93% colour, 98% turbidity and 86% E. coli. Tests on model water, using a secondary treatment stage sand filter showed maximum turbidity removal of 97% and maximum E. coli reduction of 98% using M. oleifera, compared with 100% turbidity and 97% E. coli for alum. Although not as effective as alum or ferric, M. oleifera showed sufficient removal capability to encourage its use for treatment of turbid waters in developing countries.

Rancang Bangun Sistem Scada (Supervisory Control And Data Acquisition pada Instalasi Pengolahan Air Sungai Cihideung Institut Pertanian Bogor

Directory of Open Access Journals (Sweden)

Agus Eko Handoko

2017-08-01

Full Text Available Abstract SCADA is a combination of telemetry and data acquisition. SCADA proceeding by means of accumulating some information and return back to center controlling, it is also implementing every analysis and necessary control through PID control system as a control parameter to SCADA input data system in this research. In designing PID control system it is needed the arrangement of P, I and D parameter in order to acquire output signal system to particular input system which has adjusted to necessity. The research was implemented on Water Treatment Plant in Bogor Agricultural University at Cihideung's area region. The NTU score as a starting operational data is necessary as a bench mark in PAC dose application which is obtained from the samples of morning and afternoon raw water and dose proportion is 75% for 14kgs PAC mixed with 200 Litre water within 30 NTU as the maximal treatment. 75% dose application can be imposed for 7 hours PAC usage. The result of research indicated that the variety of percentages value in PAC dose application delivered the advantage in operating of clean water processing installation particularly for PAC needed. Design Of SCADA System SCADA indicated the outcome of unit data acquirement on certain period to determine the PAC necessity in operating Water Treatment Plant.

Modelling the risk of mortality of Corbicula fluminea (Müller, 1774) (Bivalvia: Corbiculidae) exposed to different turbidity conditions.

Science.gov (United States)

Avelar, W E P; Neves, F F; Lavrador, M A S

2014-05-01

The provision of sediment in rivers, due to erosion processes that occur in the environment, consists of a major source of pollution and alteration of the physicochemical conditions of water resources. In addition, the increase in water turbidity may cause siltation, dramatically impacting aquatic communities. Specifically considering the bivalve Corbicula fluminea (Müller, 1774), the aim of this study was to analyse the effect of exposure to different turbidity conditions of sediments, as a risk factor for the animals. For this purpose, a docking device was designed to ensure water circulation in a closed system and to maintain the desired levels of turbidity. Although C. fluminea can generally tolerate environmental changes in aquatic systems, an intolerance to high turbidity levels was experimentally observed, expressed by the mortality rate of the animals when exposed to conditions above 150 nephelometric turbidity units (NTU). This value was similar to the one recorded at study sites in the rivers Pardo (Serrana-SP-Brazil) and Mogi Guaçu (Porto Ferreira-SP-Brazil) during the rainy season. Using a logistic regression model, the experimental results were analysed and the observed mortality rates indicate that the exposure of the animals to turbidity levels above 150 nephelometric turbidity units (NTU), for periods longer than 120 hours, may be considered a probable cause of mortality for the species.

A New Model and Its Implementation of Academic Resources Services for Academic Libraries

Directory of Open Access Journals (Sweden)

Yu-Ting Chiang

2006-12-01

Full Text Available Internet has become one of the important channels for retrieval of academic resources in the recent years. The roles and service models of academic libraries has been changed accordingly. Most academic libraries have been providing subject directory (subject gateway for users to browse the highly selected academic resources. On the contrary, few academic libraries managed to provide academic resources for user to retrieve. This article proposes a new model which the libraries will cooperate with search engine providers to support the full-text retrieval for academic resources in a low cost. We discuss the design and implementation of “NTU Scholars Gateway” based on the new model. In addition, the functionalities and future development of NTU Scholars Gateway are discussedas well. [Article content in Chinese

Research on the treatment of liquid waste containing cesium by an adsorption-microfiltration process with potassium zinc hexacyanoferrate

International Nuclear Information System (INIS)

Zhang Changping; Gu Ping; Zhao Jun; Zhang Dong; Deng Yue

2009-01-01

The removal of cesium from an aqueous solution by an adsorption-microfiltration (AMF) process was investigated in jar tests and lab-scale tests. The adsorbent was K 2 Zn 3 [Fe(CN) 6 ] 2 . The obtained cesium data in the jar test fit a Freundlich-type isotherm well. In the lab-scale test, the mean cesium concentration of the raw water and the effluent were 106.87 μg/L and 0.59 μg/L, respectively, the mean removal of cesium was 99.44%, and the mean decontamination factors (DF) and concentration factors (CF) were 208 and 539, respectively. The removal of cesium in the lab-scale test was better than that in the jar test because the old adsorbents remaining in the reactor still had adsorption capacity with the premise of no significant desorption being observed, and the continuous renewal of the adsorbent surface improved the adsorption capacity of the adsorbent. Some of the suspended solids were deposited on the bottom of the reactor, which would affect the mixing of adsorbents with the raw water and the renewing of the adsorbent surface. Membrane fouling was the main physical fouling mechanism, and the cake layer was the main filtration resistance. Specific flux (SF) decreased step by step during the whole period of operation due to membrane fouling and concentration polarization. The quality of the effluent was good and the turbidity remained lower than 0.1 NTU, and the toxic anion, CN - , could not be detected because of its low concentration, this indicated that the effluent was safe. The AMF process was feasible for practical application in the treatment of liquid waste containing cesium.

Research on the treatment of liquid waste containing cesium by an adsorption-microfiltration process with potassium zinc hexacyanoferrate.

Science.gov (United States)

Zhang, Chang-Ping; Gu, Ping; Zhao, Jun; Zhang, Dong; Deng, Yue

2009-08-15

The removal of cesium from an aqueous solution by an adsorption-microfiltration (AMF) process was investigated in jar tests and lab-scale tests. The adsorbent was K(2)Zn(3)[Fe(CN)(6)](2). The obtained cesium data in the jar test fit a Freundlich-type isotherm well. In the lab-scale test, the mean cesium concentration of the raw water and the effluent were 106.87 microg/L and 0.59 microg/L, respectively, the mean removal of cesium was 99.44%, and the mean decontamination factors (DF) and concentration factors (CF) were 208 and 539, respectively. The removal of cesium in the lab-scale test was better than that in the jar test because the old adsorbents remaining in the reactor still had adsorption capacity with the premise of no significant desorption being observed, and the continuous renewal of the adsorbent surface improved the adsorption capacity of the adsorbent. Some of the suspended solids were deposited on the bottom of the reactor, which would affect the mixing of adsorbents with the raw water and the renewing of the adsorbent surface. Membrane fouling was the main physical fouling mechanism, and the cake layer was the main filtration resistance. Specific flux (SF) decreased step by step during the whole period of operation due to membrane fouling and concentration polarization. The quality of the effluent was good and the turbidity remained lower than 0.1NTU, and the toxic anion, CN(-), could not be detected because of its low concentration, this indicated that the effluent was safe. The AMF process was feasible for practical application in the treatment of liquid waste containing cesium.

Phase II in-stream sediment measurements in the Talakhaya watershed on Rota, Commonwealth of the Northern Mariana Islands from 2016-03-09 to 2017-05-11 (NCEI Accession 0166379)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The dataset includes TSS (mg/L), turbidity (NTU), stream level (ft), and precipitation (in) data collected at multiple stations across five streams and at four rain...

Doubtful records of reptile species in some areas of the Danube Delta Biosphere Reserve (Romania

Directory of Open Access Journals (Sweden)

TÖRÖK Zsolt Csaba

2012-09-01

Full Text Available In the present paper there are provided details on the doubtful data on the occurrence of some reptile species in various parts of the Danube Delta Biosphere Reserve. Testudo graeca was indicated by mistake at Sfântu Gheorghe (probably the authors saw the species in some places from the continental plateau nearby of Sfântu Gheorghe branch, not inside the Danube Delta. Lacerta viridis was mentioned in the so-called “maritime Delta” and at the ruins of Histria fortress (due to confusion with specimens of Lacerta agilis. Also, Podarcis muralis was “recorded” at the ruins of Histria fortress (due to misidentification of specimens belonging to species P. taurica. A corps of snake found at Letea forest was considered by mistake as belonging to species Eryx jaculus. In several official reports (grey literature the species Elaphe longissima (Zamenis longissimus was mentioned by mistake as occurring at Letea forest. Elaphe (quatuorlineata sauromates was “recorded” at the ruins of Histria fortress and at Sfântu Gheorghe due to confusion with specimens belonging to other snake species. Specimens of Vipera urisnii from the Danube Delta were considered as belonging to the species Vipera berus. Also, Vipera ursinii was metioned by mistake at Caraorman marine levee and at Chituc marine levee, based only on the idea that if the species occurs on other marine levees, it has to be present on these two marine levees, too.

Application of thermotolerant microorganisms for biofertilizer preparation.

Science.gov (United States)

Chen, Kuo-Shu; Lin, Yann-Shying; Yang, Shang-Shyng

2007-12-01

Intensive agriculture is practised in Taiwan, and compost application is very popular as a means of improving the soil physical properties and supplying plant nutrition. We tested the potential of inoculation with thermotolerant microorganisms to shorten the maturity and improve the quality of biofertilizer prepared by composting. Thermotolerant microorganisms were isolated from compost and reinoculated for the preparation of biofertilizer. The physical, chemical and biological properties of the biofertilizer were determined during composting. The effects of biofertilizer application on the growth and yield of rape were also studied. Among 3823 colonies of thermotolerant microorganisms, Streptomyces thermonitrificans NTU-88, Streptococcus sp. NTU-130 and Aspergillus fumigatus NTU-132 exhibited high growth rates and cellulolytic and proteolytic activities. When a mixture of rice straw and swine manure were inoculated with these isolates and composted for 61 days, substrate temperature increased initially and then decreased gradually during composting. Substrate pH increased from 7.3 to 8.5. Microbial inoculation enhanced the rate of maturity, and increased the content of ash and total and immobilized nitrogen, improved the germination rate of alfalfa seed, and decreased the content of total organic carbon and the carbon/nitrogen ratio. Biofertilizer application increased the growth and yield of rape. Inoculation of thermotolerant and thermophilic microorganisms to agricultural waste for biofertilizer preparation enhances the rate of maturity and improves the quality of the resulting biofertilizer. Inoculation of appropriate microorganisms in biofertilizer preparation might be usefully applied to agricultural situations.

Assessment Of The Physicochemical And Microbial Quality Of Water In Ke-Nya Stream At Babato-Kuma Community In The Kintampo North Municipal Assembly Of Brong Ahafo Region Of Ghana

Directory of Open Access Journals (Sweden)

Frimpong

2015-06-01

Full Text Available ABSTRACT The study was carried out to evaluate the physicochemical and microbiological quality of the Ke-enya stream which is relied on by the inhabitants of Babato-kuma and its surrounding villages for their domestic and Agricultural activities. A total of twenty eight 28 water samples were collected at upstream midstream and downstream from November 2012 to January 2013 for analysis. Most of the physicochemical parameters were within WHO guidelines recommended for potable water with the exception of Turbidity and Colour which exceeded the WHO standard of 5 NTU and 15 Hz respectively. Colour ranged from 100 to 130 Hz with a mean of 1179.45 Hz whiles Turbidity ranged from 9 to 36 NTU with a mean of 20.7810.5 NTU. However Total Coliform 420-1188 CFU100ml 757261 Faecal Coliform 140-623 CFU100ml 305145 E.coli 46-391 CFU100ml 135102 and Total Heterotrophic bacteria 444-3129 CFUml 1341778 were higher than WHO standards. Bacterial contamination could be traced to settlements along the stream livestock production poor or non-existence sewage system coupled with poor sanitary conditions among others. Alternative sources of water supplies in the form of hand-dug wells or boreholes if possible by the Municipal assembly NGOs and other philanthropies to the inhabitants whose traditional sources of drinking water is directly from this stream will be beneficial in reducing the health implications associated with this pollution.

Pilot-scale study of ballasted-flocculation technology

International Nuclear Information System (INIS)

Liem, L.E.; Brant, W.H.; Gagne, B.; Michaud, J.; Beaudet, J.-F.; Landry, D.; Braden, K.; Campbell, D.

2002-01-01

A ballasted-flocculation pilot-scale study was undertaken to treat a wide-range river water turbidity (17 to 2,608 NTU). The pilot-scale unit was operated at flowrates of 30 to 63 m 3 /h, which corresponded to loading rates of 40 to 84 m/h. Coagulants, polymers, and microsand were added to enhance the floc agglomeration. The weighted flocs settled rapidly resulting in excellent turbidity removals of 94.7 to 99.9%. At the peak turbidity, the unit had a 99.9% removal performance (2.7 from 2,608 NTU) at a loading rate of 40 m/h. In this case, polyaluminum silicosulfate and anionic polymer dosages were 82 and 1 mg/L, respectively. The microsand recycle rate was kept constant at 4.5 m 3 /h, and 1mg microsand was added for each liter of water treated. (author)

Generalized weighted ratio method for accurate turbidity measurement over a wide range.

Science.gov (United States)

Liu, Hongbo; Yang, Ping; Song, Hong; Guo, Yilu; Zhan, Shuyue; Huang, Hui; Wang, Hangzhou; Tao, Bangyi; Mu, Quanquan; Xu, Jing; Li, Dejun; Chen, Ying

2015-12-14

Turbidity measurement is important for water quality assessment, food safety, medicine, ocean monitoring, etc. In this paper, a method that accurately estimates the turbidity over a wide range is proposed, where the turbidity of the sample is represented as a weighted ratio of the scattered light intensities at a series of angles. An improvement in the accuracy is achieved by expanding the structure of the ratio function, thus adding more flexibility to the turbidity-intensity fitting. Experiments have been carried out with an 850 nm laser and a power meter fixed on a turntable to measure the light intensity at different angles. The results show that the relative estimation error of the proposed method is 0.58% on average for a four-angle intensity combination for all test samples with a turbidity ranging from 160 NTU to 4000 NTU.

make up.contents pg

African Journals Online (AJOL)

spamer

canalized inlets on the south-west side of the harbour and supply minimal .... lometric turbidity units – NTU) were measured during the collection of each sample. ...... occurring in the western North Atlantic Ocean, Cape Hatteras to the southern ...

Multiple Active Volcanoes in the Northeast Lau Basin

Science.gov (United States)

Baker, E. T.; Resing, J. A.; Lupton, J. E.; Walker, S. L.; Embley, R. W.; Rubin, K. H.; Buck, N.; de Ronde, C. E.; Arculus, R. J.

2010-12-01

The northeast Lau Basin occupies a complex geological area between the Tafua arc front, the E-W trending Tonga Trench, and the Northeast Lau Spreading Center. These boundaries create multiple zones of extension and thus provide abundant opportunities for magma to invade the crust. The 25-km-long chain of “Mata” volcanoes lies near the center of this area, separated from both the arc front and the spreading ridge. In 2008 we discovered hydrothermal venting on the largest and most southerly of these volcanoes, W and E Mata. In 2010 we visited the 7 smaller volcanoes that form a 15-km-long arcuate sweep to the north from W and E Mata (the “North Matas”). We also revisited W and E Mata. Over each volcano we conducted CTD tows to map plumes and collect water samples. Based on the CTD results, camera tows searched for seafloor sources on three volcanoes. The N Mata volcanoes, extending from Mata Taha (1) in the south to Mata Fitu (7) in the north, lie within a prominent gap in the shallow bathymetry along the southern border of the Tonga trench. Northward from E Mata the Mata volcanoes degrade from large symmetrical cones to smaller and blocky volcanic edifices. Summit depths range from 1165 m (W Mata) to 2670 m (Mata Nima (5)). The most active volcano in the chain is the erupting W Mata, with an intense plume that extended 250 m above the summit. Hydrothermal temperature anomalies (Δθ, corrected for hydrographic masking effects) reached ˜1.7°C, with light-scattering values as high as 2-5 ΔNTU. The 2010 surveys now show that 6 of the 7 N Mata volcanoes are also hydrothermally active. Along the N Matas, Δθ and ΔNTU signals ranged from robust to weak, but distinct oxidation-reduction potential (aka Eh) anomalies confirmed active venting in each case. The most concentrated plumes were found near Mata Ua (2) and Mata Fitu (7), with Δθ and ΔNTU maxima of 0.1-0.17°C and 0.3, respectively. Despite the variability in plume strength, however, ΔNTU/Δθ ratios

Latent effectiveness of desiccant wheel: A silica gels- water system

International Nuclear Information System (INIS)

Rabah, A. A.; Mohamed, S. A.

2009-01-01

A latent heat effectiveness model in term of dimensionless groups? =f (NTU, m * ,Crm * ) for energy wheel has been analytically derived. The energy wheel is divided into humidification and dehumidification sections. For each section macroscopic mass differential equations for gas and the matrix were applied. In this process local latent effectiveness (? c ,? h ) for the humidification and dehumidification section of the wheel were obtained. The Latent effectiveness of the wheel is then derived form local effectiveness [? =f (? c ,? h)]. The model is compared with the existing experimental investigation and manufacturer data for energy wheel. More than 90% of the experimental data within a confidence limit of 95%. (Author)

Design and Implementation of NTU Wearable Exoskeleton as an Enhancement and Assistive Device

OpenAIRE

Low, K. H.; Liu, X.; Yu, H.

2006-01-01

This article presents a wearable lower extremity exoskeleton (LEE) developed to enhance the ability of a human’s walking while carrying heavy loads. The ultimate goal of the current research work is to design and control a power assist system that integrates a human’s intellect for feedback and sensory purposes. The exoskeleton system in this work consists of an inner exoskeleton and an outer exoskeleton. The inner exoskeleton measures the movements of the wearer and provides these measuremen...

Design and Implementation of NTU Wearable Exoskeleton as an Enhancement and Assistive Device

Directory of Open Access Journals (Sweden)

K. H. Low

2006-01-01

Full Text Available This article presents a wearable lower extremity exoskeleton (LEE developed to enhance the ability of a human’s walking while carrying heavy loads. The ultimate goal of the current research work is to design and control a power assist system that integrates a human’s intellect for feedback and sensory purposes. The exoskeleton system in this work consists of an inner exoskeleton and an outer exoskeleton. The inner exoskeleton measures the movements of the wearer and provides these measurements to the outer exoskeleton, which supports the whole exoskeleton system to walk following the wearer. A special footpad, which is designed and attached to the outer exoskeleton, can measure the zero moment point (ZMP of the human as well as that of the exoskeleton in time. Using the measured human ZMP as the reference, the exoskeleton’s ZMP is controlled by trunk compensation so that the exoskeleton can walk stably. A simulation platform has first been developed to examine the gait coordination through inner and outer exoskeletons. A commercially available software, xPC Target, together with other toolboxes from MATLAB, has then been used to provide a real-time operating system for controlling the exoskeleton. Real-time locomotion control of the exoskeleton is implemented in the developed environment. Finally, some experiments on different objects showed that the stable walking can be achieved in the real environment.

Nitrate and Perchlorate Destruction and Potable Water Production Using Membrane Biofilm Reduction

Science.gov (United States)

2014-01-01

NDMA N-nitrosodimethylamine NDPA N-nitroso-di-n-propylamine ng/L nanograms per liter NO2- nitrite NO3- nitrate NTU nephelometric turbidity units...Nitrosamines including N-nitrosodiethylamine (NDEA), N- nitrosodimethylamine ( NDMA ), and N-nitroso-di-n-propylamine (NDPA) were below their

Download this PDF file

African Journals Online (AJOL)

designed to work at declining rate taking into account economic factors and the intermittent trend of ... Turbidity Unit (NTU) for three weeks without losing its capacity and efficiency but for higher turbidities ..... 3 to 4 hours of operation. If water is ...

The influence of the solid thermal conductivity on active magnetic regenerators

DEFF Research Database (Denmark)

Nielsen, Kaspar Kirstein; Engelbrecht, Kurt

2012-01-01

The influence of the thermal conductivity of the regenerator solid on the performance of a flat plate active magnetic regenerator (AMR) is investigated using an established numerical AMR model. The cooling power at different (fixed) temperature spans is used as a measure of the performance...... for a range of thermal conductivities, operating frequencies, a long and short regenerator, and finally a regenerator with a low and a high number of transfer units (NTU) regenerator. In this way the performance is mapped out and the impact of the thermal conductivity of the solid is probed. Modeling shows...... that under certain operating conditions, the AMR cycle is sensitive to the solid conductivity. It is found that as the operating frequency is increased it is not only sufficient to have a high NTU regenerator but the regenerator performance will also benefit from increased thermal conductivity in the solid...

TROVE: A User-friendly Tool for Visualizing and Analyzing Cancer Hallmarks in Signaling Networks.

Science.gov (United States)

Chua, Huey Eng; Bhowmick, Sourav S; Zheng, Jie

2017-09-22

Cancer hallmarks, a concept that seeks to explain the complexity of cancer initiation and development, provide a new perspective of studying cancer signaling which could lead to a greater understanding of this complex disease. However, to the best of our knowledge, there is currently a lack of tools that support such hallmark-based study of the cancer signaling network, thereby impeding the gain of knowledge in this area. We present TROVE, a user-friendly software that facilitates hallmark annotation, visualization and analysis in cancer signaling networks. In particular, TROVE facilitates hallmark analysis specific to particular cancer types. Available under the Eclipse Public License from: https://sites.google.com/site/cosbyntu/softwares/trove and https://github.com/trove2017/Trove. hechua@ntu.edu.sg or assourav@ntu.edu.sg. © The Author (2017). Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com

Preliminary study on the effect of mixing and time on turbidity removal in wastewater treatment

International Nuclear Information System (INIS)

Abu Bakar, A.; Jaafar, J.

2006-01-01

The current trend favorable in the wastewater treatment industry is to use natural polymer as a coagulant. It is believed that this natural polymer can perform as well as synthetic organic polymer. In this study, natural polymer - Moringa Oleifera was used to destabilize the colloidal particles in wastewater so that the floc will be formed in this process. Jar test was used to evaluate, to determine the dosages and to optimize the coagulant - Moringa Oleifera in these processes. The experimental result has showed that, by using Moringa Oleifera as a coagulant the turbidity of the wastewater can be removed up to 98% which is comparable to the performance of synthetic polymer, alum. This study however is applicable for wastewater which in the medium to high turbidity ranging from 80 to 100 NTU. (Author)

Minimum number of transfer units and reboiler duty for multicomponent distillation columns

International Nuclear Information System (INIS)

Pleşu, Valentin; Bonet Ruiz, Alexandra Elena; Bonet, Jordi; Llorens, Joan; Iancu, Petrica

2013-01-01

Some guidelines to evaluate distillation columns, considering only basic thermodynamic data and principles, are provided in this paper. The method allows a first insight to the problem by simple calculations, without requiring column variables to ensure rational use of energy and low environmental impact. The separation system is approached by two complementary ways: minimum and infinite reflux flow rate. The minimum reflux provides the minimum energy requirements, and the infinite reflux provides the feasibility conditions. The difficulty of separation can be expressed in terms of number of transfer units (NTU). The applicability of the method is not mathematically limited by the number of components in the mixture. It is also applicable to reactive distillation. Several mixtures, including reactive distillation, are rigorously simulated as illustrative examples, to verify the applicability of the approach. The separation of the mixtures, performed by distillation columns, is feasible if a minimum NTU can be calculated between the distillate and bottom products. Once verified the feasibility of the separation, the maximum thermal efficiency depends only on boiling point of bottom and distillate streams. The minimum energy requirements corresponding to the reboiler can be calculated from the maximum thermal efficiency, and the variation of entropy and enthalpy of mixing between distillate and bottom streams. -- Highlights: • Feasibility analysis complemented with difficulty of separation parameters • Minimum and infinite reflux simplified models for distillation columns • Minimum number of transfer units (NTU) for packed columns at early design stages • Calculation of minimum energy distillation requirements at early design stages • Thermodynamic cycle approach and efficiency for distillation columns

Evaluation of the Hydrolab HL4 water-quality sonde and sensors

Science.gov (United States)

Snazelle, Teri T.

2017-12-18

, but one sonde exceeded the allowable difference criteria when tested in pH 5.00 buffer and at 40 ºC. The USGS criteria and the technical specifications for turbidity were met by one sonde in standards ranging from 10 to 3,000 nephelometric turbidity units (NTU). A second sonde met the USGS criteria and the technical specifications except in the 3,000-NTU standard, and the third sonde exceeded the USGS calibration criteria in the 10- and 20-NTU standards and the technical specifications in the 20-NTU standard.Results of the field test showed acceptable performance and revealed that differences in data sample processing between sonde manufacturers may result in variances between the reported measurements when comparing one sonde to another. These variances in data would be more pronounced in dynamic site conditions. The lack of a wiper or other sensor-cleaning device on the DO sensor could prove problematic, and could limit the use of the HL4 to profiling applications or at sites with limited biofouling.

Using magnetic seeds to improve the aggregation and precipitation of nanoparticles from backside grinding wastewater.

Science.gov (United States)

Wan, Terng-Jou; Shen, Shu-Min; Siao, Sheng-Han; Huang, Chong-Fu; Cheng, Chiung-Yi

2011-12-01

Backside grinding (BG) wastewater treatment typically requires large quantities of chemicals, i.e. polyaluminum chloride (PAC) coagulant and produces considerable amounts of sludge, increasing the loading and cost of subsequent sludge treatment and disposal processes. This study investigated the effects of the addition of magnetic seeds (FeO*Fe(2)O(3)) of selected particle sizes and of optimized combinations of magnetic seeds and PAC on the aggregation of silica nanoparticles from BG wastewater and on the sedimentation time at various pH values. The results show that the turbidity of BG wastewater was significantly reduced by the magnetic aggregation treatment. The dosage of PAC combined with 2.49gL(-1) or 1.24gL(-1) of magnetic seeds was reduced by 83% (from 60 to 10mgL(-1)) compared to the conventional process of using only PAC as a coagulant. The turbidity of the BG wastewater, initially 1900-2500NTU, could also be successfully decreased about to 23NTU by the addition of 3.74gL(-1) magnetite (FeO*Fe(2)O(3)) only at pH 5 with an applied magnetic field of 1000G. Different coagulation conditions using magnetic seeds combined with coagulant resulted in different aggregation performances. The treatment performance was more effective by using two-stage dosing, in which magnetic seeds and PAC were added separately, than that with one-stage dosing, where the magnetic seeds and PAC were added simultaneously during rapid mixing. The two-stage dosing allowed for a reduction in the optimum dosage of magnetic seeds from 3.74gL(-1) to 2.49gL(-1) or 1.24gL(-1) without affecting performance when coupled with 0.01gL(-1) of PAC coagulant. The developed method effectively reduced the production of waste sludge. Copyright © 2011 Elsevier Ltd. All rights reserved.

Depth Filters Containing Diatomite Achieve More Efficient Particle Retention than Filters Solely Containing Cellulose Fibers.

Science.gov (United States)

Buyel, Johannes F; Gruchow, Hannah M; Fischer, Rainer

2015-01-01

The clarification of biological feed stocks during the production of biopharmaceutical proteins is challenging when large quantities of particles must be removed, e.g., when processing crude plant extracts. Single-use depth filters are often preferred for clarification because they are simple to integrate and have a good safety profile. However, the combination of filter layers must be optimized in terms of nominal retention ratings to account for the unique particle size distribution in each feed stock. We have recently shown that predictive models can facilitate filter screening and the selection of appropriate filter layers. Here we expand our previous study by testing several filters with different retention ratings. The filters typically contain diatomite to facilitate the removal of fine particles. However, diatomite can interfere with the recovery of large biopharmaceutical molecules such as virus-like particles and aggregated proteins. Therefore, we also tested filtration devices composed solely of cellulose fibers and cohesive resin. The capacities of both filter types varied from 10 to 50 L m(-2) when challenged with tobacco leaf extracts, but the filtrate turbidity was ~500-fold lower (~3.5 NTU) when diatomite filters were used. We also tested pre-coat filtration with dispersed diatomite, which achieved capacities of up to 120 L m(-2) with turbidities of ~100 NTU using bulk plant extracts, and in contrast to the other depth filters did not require an upstream bag filter. Single pre-coat filtration devices can thus replace combinations of bag and depth filters to simplify the processing of plant extracts, potentially saving on time, labor and consumables. The protein concentrations of TSP, DsRed and antibody 2G12 were not affected by pre-coat filtration, indicating its general applicability during the manufacture of plant-derived biopharmaceutical proteins.

Depth filters containing diatomite achieve more efficient particle retention than filters solely containing cellulose fibers

Directory of Open Access Journals (Sweden)

Johannes Felix Buyel

2015-12-01

Full Text Available The clarification of biological feed stocks during the production of biopharmaceutical proteins is challenging when large quantities of particles must be removed, e.g. when processing crude plant extracts. Single-use depth filters are often preferred for clarification because they are simple to integrate and have a good safety profile. However, the combination of filter layers must be optimized in terms of nominal retention ratings to account for the unique particle size distribution in each feed stock. We have recently shown that predictive models can facilitate filter screening and the selection of appropriate filter layers. Here we expand our previous study by testing several filters with different retention ratings. The filters typically contain diatomite to facilitate the removal of fine particles. However, diatomite can interfere with the recovery of large biopharmaceutical molecules such as virus-like particles and aggregated proteins. Therefore, we also tested filtration devices composed solely of cellulose fibers and cohesive resin. The capacities of both filter types varied from 10 to 50 L m-2 when challenged with tobacco leaf extracts, but the filtrate turbidity was ~500-fold lower (~3.5 NTU when diatomite filters were used. We also tested pre coat filtration with dispersed diatomite, which achieved capacities of up to 120 L m-2 with turbidities of ~100 NTU using bulk plant extracts, and in contrast to the other depth filters did not require an upstream bag filter. Single pre-coat filtration devices can thus replace combinations of bag and depth filters to simplify the processing of plant extracts, potentially saving on time, labor and consumables. The protein concentrations of TSP, DsRed and antibody 2G12 were not affected by pre-coat filtration, indicating its general applicability during the manufacture of plant-derived biopharmaceutical proteins.

A biocoagulant slow sand filtration for disinfection of Toxoplasma ...

African Journals Online (AJOL)

An integrated low-tech biocoagulant-sand filter drum for disinfection of oocysts of Toxoplasma gondii targeted for developing countries was evaluated. Dirty and turbid water (130.3 NTU) from Mezam River and leachates from dump sites and stagnant water in Bamenda, Cameroon, was analyzed microscopically after ...

78 FR 72643 - Taking of Marine Mammals Incidental to Specified Activities: Mukilteo Ferry Terminal Construction...

Science.gov (United States)

2013-12-03

... management purposes, differences in mean pupping date (Temte 1986), movement patterns (Jeffries 1985; Brown... of noise sources and their paths) and the receiving animals (hearing, motivation, experience... compliance radius of 150 feet (from three timber pile removal events) were generally less than 0.5 NTU higher...

76 FR 33753 - Modification of the Expiration Date for the National Pollutant Discharge Elimination System...

Science.gov (United States)

2011-06-09

... Hampshire, New Mexico, Puerto Rico, Washington, DC, and U.S. territories and protectorates). The proposed... the December 2009 final rule regarding the calculation of the numeric limitation on turbidity. This... construction sites to a numeric effluent limitation of 280 NTU for the pollutant turbidity starting in August...

EVALUACIÓN DE CAL, SULFATO E HIDROXICLORURO DE ALUMINIO EN LA COAGULACION-FLOCULACION DEL LIXIVIADO DEL RELLENO SANITARIO DE POZA RICA, VERACRUZ

Directory of Open Access Journals (Sweden)

Israel Hernández

2013-01-01

Full Text Available En el presente artículo se reporta el proceso de clarificación del lixiviado de un basurero de la Ciudad de Poza Rica de Hidalgo, Veracruz, con este fin se utilizó como coagulantes óxido de calcio, sulfato e hidroxicloruro de aluminio. El CaO no presentó capacidad floculante para el lixiviado tratado bajo ninguna de las condiciones ensayadas. El Al2(SO43 mostró buena actividad floculante al tratar el lixiviado obteniéndose 0.97 NTU en el índice de turbidez con 2250 ppm del sulfato de aluminio, por la elevada cantidad de floculante el proceso caro; por otra parte, la floculación de los sólidos suspendidos en el lixiviado se logró una mayor extensión empleando 1.5 ppm de Al2(OH5Cl2*5H2O obteniendo un índice de turbidez de 0.83 NTU, con pH de 7.63.

Towards environmental management of water turbidity within open coastal waters of the Great Barrier Reef.

Science.gov (United States)

Macdonald, Rachael K; Ridd, Peter V; Whinney, James C; Larcombe, Piers; Neil, David T

2013-09-15

Water turbidity and suspended sediment concentration (SSC) are commonly used as part of marine monitoring and water quality plans. Current management plans utilise threshold SSC values derived from mean-annual turbidity concentrations. Little published work documents typical ranges of turbidity for reefs within open coastal waters. Here, time-series turbidity measurements from 61 sites in the Great Barrier Reef (GBR) and Moreton Bay, Australia, are presented as turbidity exceedance curves and derivatives. This contributes to the understanding of turbidity and SSC in the context of environmental management in open-coastal reef environments. Exceedance results indicate strong spatial and temporal variability in water turbidity across inter/intraregional scales. The highest turbidity across 61 sites, at 50% exceedance (T50) is 15.3 NTU and at 90% exceedance (T90) 4.1 NTU. Mean/median turbidity comparisons show strong differences between the two, consistent with a strongly skewed turbidity regime. Results may contribute towards promoting refinement of water quality management protocols. Copyright © 2013 Elsevier Ltd. All rights reserved.

Waste water regeneration technologies: the experience of a pilot plant using an MBR process and micro-ultrafiltration and reverse osmosis in the waste water treatment plant at Canals-Lucidol de Cre spins (Valencia, Spain); Tecnologias para la regeneracion de aguas residuales: experiencia con planta piloto mediante un proceso MBR y membranas de micro-ultrafiltracion y osmosis inversa en la EDAR de Canals-L' Alcudia de Crespins (Valencia)

Energy Technology Data Exchange (ETDEWEB)

Martinez Muro, J. L.; Garcia Garcia, J. J.; Morenilla Martinez, J. J.; Bernacer Bonora, I.; Lloret Salinas, R.; Pascual Garrido, J.; Escribano Romero, F.; Zarzo Martinez, D.

2006-07-01

This article looks at membrane bioreactor (MBR) technology and the use of micro-ultrafiltration membranes systems for treating sewage prior to reverse osmosis to desalinate sewage plant affluent. MBR technology ensures stable effluent quality (it is not affected by problems of sedimentation of the biological sludge in the clarifier) and practical disinfecting of the sludge. Micro-ultra-filtration technologies, either as treatment prior to reverse osmosis, or as independent tertiary treatment systems, generally guarantee extremely demanding permeate characteristics: SDI15 < 3-fouling index-, absence of microbiological organisms, and cloudines < 1 NTU. (Author)

76 FR 22891 - Modification to 2008 National Pollutant Discharge Elimination System (NPDES) General Permit for...

Science.gov (United States)

2011-04-25

... statements and data pertaining to the proposed permit at the public hearing. E. Finalizing This Action This... in the December 2009 final rule regarding the calculation of the numeric limitation on turbidity... construction sites to a numeric effluent limitation of 280 NTU for the pollutant turbidity starting in August...

Regional travel-time residual studies and station correction from 1-D velocity models for some stations around Peninsular Malaysia and Singapore

Science.gov (United States)

Osagie, Abel U.; Nawawi, Mohd.; Khalil, Amin Esmail; Abdullah, Khiruddin

2017-06-01

We have investigated the average P-wave travel-time residuals for some stations around Southern Thailand, Peninsular Malaysia and Singapore at regional distances. Six years (January, 2010-December, 2015) record of events from central and northern Sumatra was obtained from the digital seismic archives of Integrated Research Institute for Seismology (IRIS). The criteria used for the data selection are designed to be above the magnitude of mb 4.5, depth less than 200 km and an epicentral distance shorter than 1000 km. Within this window a total number of 152 earthquakes were obtained. Furthermore, data were filtered based on the clarity of the seismic phases that are manually picked. A total of 1088 P-wave arrivals and 962 S-wave arrivals were hand-picked from 10 seismic stations around the Peninsula. Three stations IPM, KUM, and KOM from Peninsular Malaysia, four stations BTDF, NTU, BESC and KAPK from Singapore and three stations SURA, SRIT and SKLT located in the southern part of Thailand are used. Station NTU was chosen as the Ref. station because it recorded the large number of events. Travel-times were calculated using three 1-D models (Preliminary Ref. Earth Model PREM (Dziewonski and Anderson, 1981, IASP91, and Lienert et al., 1986) and an adopted two-point ray tracing algorithm. For the three models, we corroborate our calculated travel-times with the results from the use of TAUP travel-time calculation software. Relative to station NTU, our results show that the average P wave travel-time residual for PREM model ranges from -0.16 to 0.45 s for BESC and IPM respectively. For IASP91 model, the average residual ranges from -0.25 to 0.24 s for SRIT and SKLT respectively, and ranges from -0.22 to 0.30 s for KAPK and IPM respectively for Lienert et al. (1986) model. Generally, most stations have slightly positive residuals relative to station NTU. These corrections reflect the difference between actual and estimated model velocities along ray paths to stations and

Programme de petites subventions visant à renforcer les capacités ...

International Development Research Centre (IDRC) Digital Library (Canada)

Agent(e) responsable du CRDI. Smith, Matthew. Financement total. CAD$ 948,653. Pays. Asie centrale, Extrême-Orient, Asie du sud. Chargé(e) de projet. Ang Peng Hwa. Institution. Nanyang Technological University. Pays d' institution. Singapour. Site internet. http://www.ntu.edu.sg. Extrants. Documents. Media Asia : an ...

40 CFR 141.721 - Reporting requirements.

Science.gov (United States)

2010-07-01

... operational data for toolbox options. Microbial Toolbox Reporting Requirements Toolbox option Systems must... coagulant (iv) At least 0.5-log mean reduction of influent turbidity or compliance with alternative State... treatment compliance date in § 141.713. (ii) If monthly average of daily max turbidity is greater than 1 NTU...

Comparison of “Morning Olifera Seed Extract and Magnafloc LT25” in Removal of Water Turbidity Case Study: Tehran’s Jalalieh (1 Water Treatment Plant

Directory of Open Access Journals (Sweden)

Mehdi Khan ahmadi

2013-08-01

Full Text Available Coagulation-flocculation is one of the most important processes for water treatment, commonly used all over the world. The use of synthetic polymers known as “Polyelectrolytes as a coagulant aid is now wide spread in water treatment plants. Tehran’s “Jalalieh WTP” has been using an anionic polyelectrolyte under the trade name of “Magna Floc LT25” for a number of years MagnaFloc LT25 (MF-LT25 is a synthetic coagulant with high molecular weight, produced in granular and powder form. The application of this coagulant aid is known to be most effective if injected to water after addition of main coagulant (Ferric Chloride in Tehran’s WTP.  However the use of synthetic polymers in treatment of drinking water has always been under question due to extract of MO seed contains proteins soluble in water which have high coagulating properties. This pilot scale study was performed to compare the coagulating properties of seed extract of MO to MF-LT25, The tests were carried out on Tehran’s raw water in Jalalieh treatment plant. Several turbidity ranges such as 5, 20, 100, and 200 NTU were used representing real seasonal turbidities of influent water to treatment plant. Optimum concentration of the coagulant and coagulant aid was determined within water pH values of 6, 7 and 8, using common “Jar Test” technique. The extract of Moringa Oleifera seed in optimum concentration of 10, 14,25,35 mg/L and optimum pH of 8 is capable in removal of 96.5, 97.4, 98.5 and 99% of water turbidity range of 5, 20, 100, and 200 NTU respectively. Under similar conditions, MF-LT25 removal efficiency were found 97, 98.1, 98.4 and 99.4% of water turbidity range of 5, 20, 100, and 200 NTU at optimum concentrations of 0.015, 0.02, 0.025, 0.03 mg/L respectively. The results also showed that the extract of Moringa Oleifera seed is a powerful coagulating agent, at alkalinity pH values, and is more effective for high turbid waters. It compared well with synthetic

Split heat pipe heat recovery system

OpenAIRE

E. Azad

2008-01-01

This paper describes a theoretical analysis of a split heat pipe heat recovery system. The analysis is based on an Effectiveness-NTU approach to deduce its heat transfer characteristics. In this study the variation of overall effectiveness of heat recovery with the number of transfer units are presented. Copyright , Manchester University Press.

A comprehensive parameter study of an active magnetic regenerator using a 2D numerical model

DEFF Research Database (Denmark)

Nielsen, Kaspar Kirstein; Bahl, Christian Robert Haffenden; Smith, Anders

2010-01-01

and exergy. The results show that the optimal AMR should have a utilization in the range 0.2–1 and an NTU higher than 10 and not necessarily more than 30. It is concluded that parallel plate-based regenerators face significant challenges in terms of manufacturability. However, the benefit of parallel plate...

Study on the willingness of Sfantu Gheorghe fishermen community, from Danube Delta, to involve in decision making regarding biodiversity conservation by switching from sturgeon fishing to other natural resources

Directory of Open Access Journals (Sweden)

BOZAGIEVICI Raluca

2011-09-01

Full Text Available The investigation aimed to find out local knowledge on biodiversity conservation through sustainable use and the willingness of the local community Sfântu Gheorghe, Danube Delta, to be involved in the decision making process regarding the sustainable use of the natural resources. In obtaining the necessary information, structuredinterviews and focus group were conducted with the local population and stakeholders in order to achieve a clearer picture of all aspects of sustainable use of natural resources within the area. The results highlighted the unwillingness of local people to exploit the alternative natural resources, other than fish, available in the area and the lack of a strategy to inform and support the local community to realize projects pursuing the recovery of these resources.

LANDFILL LEACHATES PRETREATMENT BY OZONATION

Directory of Open Access Journals (Sweden)

Jacek Leszczyński

2016-06-01

Full Text Available In this paper, the application of ozonation processes for stabilized landfill leachate treatment was investigated. The leachate came from a municipal sanitary landfill located nearby Bielsk Podlaski. The average values of its main parameters were: pH 8.23; COD 870 mgO2/dm3; BOD 90 mgO2/dm3; NH4+ 136.2 mgN/dm3; UV254 absorbance 0.312 and turbidity 14 NTU. The ozone dosages used were in the range of 115.5 to 808.5 mgO3/dm3 of the leachate. The maximum COD, color and UV254 absorbance removal wa.5 mgO3/dm3. After oxidation, the ratio of BOD/COD was increased from 0.1 up to 0.23.

Mass transfer studies in miniature Rotating Disc Contactor (RDC) with 30% TBP/nitric acid biphasic system

International Nuclear Information System (INIS)

Balasubramonian, S.; Sivakumar, D.; Kumar, Shekhar; Kamachi Mudali, U.

2014-01-01

The rotating disc contactor is the widely used liquid-liquid extraction equipment for its high throughput and efficiency. In this work mass transfer performance of the miniature RDC column for the 30% TBP/nitric acid biphasic system was studied in terms of the operating variables such as rotor speed and flow rate of the aqueous and organic phase. The RDC column used in the experiments was shown. The column shell is made up of thick glass having diameter of 10.5 cm and height 100 cm. The rotor diameter is 5.3 cm and stator opening diameter is 6.3 cm. Totally 25 number of rotor discs were welded in the rotating shaft. This shaft was aligned in such a way that each rotor was placed in the centre of the compartment formed in between the two stator rings. The experiments were carried out to study the effect of rotor speed and superficial velocity of the dispersed and continuous phase on mass transfer efficiency. The organic solvent was made as the continuous phase and O/A ratio was set as 4 in both the continuous to dispersed phase(c-d) and dispersed to continuous phase (d-c) mass transfer experiments. The Number of Transfer Units (NTU) was estimated based on the solvent phase. The graphical representation of NTU was shown. The NTU value was observed as 4 and 3 respectively for extraction and stripping at the combined through put of 60 L/h and the rotor speed of 1000 rpm. This corresponds to the Height of Transfer Unit (HTU) value of 15 cm and 20 cm respectively for d-c and c-d mass transfer. The estimated overall mass transfer coefficient was increasing with rotor speed and superficial velocity of the liquid phases. The overall mass transfer coefficient also increases with increase in hold up

Site suitability for riverbed filtration system in Tanah Merah, Kelantan-A physical model study for turbidity removal

Science.gov (United States)

Ghani, Mastura; Adlan, Mohd Nordin; Kamal, Nurul Hana Mokhtar; Aziz, Hamidi Abdul

2017-10-01

A laboratory physical model study on riverbed filtration (RBeF) was conducted to investigate site suitability of soil from Tanah Merah, Kelantan for RBeF. Soil samples were collected and transported to the Geotechnical Engineering Laboratory, Universiti Sains Malaysia for sieve analysis and hydraulic conductivity tests. A physical model was fabricated with gravel packs laid at the bottom of it to cover the screen and then soil sample were placed above gravel pack for 30 cm depth. River water samples from Lubok Buntar, Kedah were used to simulate the effectiveness of RBeF for turbidity removal. Turbidity readings were tested at the inlet and outlet of the filter with specified flow rate. Results from soil characterization show that the soil samples were classified as poorly graded sand with hydraulic conductivity ranged from 7.95 x 10-3 to 6.61 x 10-2 cm/s. Turbidity removal ranged from 44.91% - 92.75% based on the turbidity of water samples before filtration in the range of 33.1-161 NTU. The turbidity of water samples after RBeF could be enhanced up to 2.53 NTU. River water samples with higher turbidity of more than 160 NTU could only reach 50% or less removal by the physical model. Flow rates of the RBeF were in the range of 0.11-1.61 L/min while flow rates at the inlet were set up between 2-4 L/min. Based on the result of soil classification, Tanah Merah site is suitable for RBeF whereas result from physical model study suggested that 30 cm depth of filter media is not sufficient to be used if river water turbidity is higher.

Remoción de nutrientes mediante coagulantes naturales y químicos en planta de tratamiento de aguas residuales, Valledupar Colombia

Directory of Open Access Journals (Sweden)

Damileth Dearmas Duarte

2015-12-01

Full Text Available Se evaluó desempeño y eficiencia de dos coagulantes químicos: sulfato de aluminio y policloruro de aluminio (PAC, y dos naturales: moringa (Moringa oleífera y cardón guajiro (Lemaireoreus griseus en la remoción de nutrientes y sedimentos del efluente de la planta de tratamiento de aguas residuales conformado por lagunas de estabilización El Salguero ubicada en el municipio de Valledupar, Cesar, Colombia. Los ensayos se llevaron a cabo con muestras de agua procedentes del río Cesar recogidas en el efluente del sistema de tratamiento. La turbidez varía desde 25 NTU hasta 67 NTU durante la época de desarrollo de la investigación. Se obtuvo que el sulfato de aluminio pese a no alcanzar la turbidez exigida por la normatividad colombiana (Decreto 3930/2010, Articulo N°72 Turbidez ≥ 5 NTU es un coagulante que remueve más del 80% de los parámetros de DQO, DBO y algas. El policloruro de aluminio es adecuado para disminuir significativamente la turbidez y los SST en un 92%, además presentó la mejor viabilidad económica de los tratamientos; y para la disminución de fosforo total resultaron efectivos los tratamientos con coagulantes naturales moringa y cardón, los cuales presentaron una remoción de 90.35%. Se concluye que los coagulantes evaluados presentan un potencial de remoción de los parámetros analizados, los resultados avalan a la Moringa oleífera como una posible alternativa natural en la potabilización de las aguas, ya que garantiza no sólo lograrcon éxito el proceso de coagulación, sino también, la ausencia de residuos

Use of submerged anaerobic membrane bioreactor (SAMBR) containing powdered activated carbon (PAC) for the treatment of textile effluents.

Science.gov (United States)

Baêta, B E L; Ramos, R L; Lima, D R S; Aquino, S F

2012-01-01

This work investigated the use of submerged anaerobic membrane bioreactors (SAMBRs) in the presence and absence of powdered activated carbon (PAC) for the treatment of genuine textile wastewater. The reactors were operated at 35 °C with an HRT of 24 h and the textile effluent was diluted (1:10) with nutrient solution containing yeast extract as the source of the redox mediation riboflavin. The results showed that although both SAMBRs exhibited an excellent performance, the presence of PAC inside SAMBR-1 enhanced reactor stability and removal efficiency of chemical oxygen demand (COD), volatile fatty acids (VFA), turbidity and color. The median removal efficiencies of COD and color in SAMBR-1 were, 90 and 94% respectively; whereas for SAMBR-2 (without PAC) these values were 79 and 86%, In addition, the median values of turbidity and VFA were 8 NTU and 8 mg/L for SAMBR-1 and 14 NTU and 26 mg/L for SAMBR-2, indicating that the presence of PAC inside SAMBR-1 led to the production of an anaerobic effluent of high quality regarding such parameters.

Analysis of Suspended-Sediment Dynamics in Gulf of Mexico Estuaries Using MODIS/Terra 250-m Imagery

Science.gov (United States)

McCarthy, M. J.; Otis, D. B.; Muller-Karger, F. E.; Mendez-Lazaro, P.; Chen, F. R.

2016-02-01

Suspended sediments in coastal ecosystems reduce light penetration, degrade water quality, and inhibit primary production. In this study, a 15-year Moderate Resolution Imaging Spectroradiometer (MODIS/Terra) turbidity time-series was developed for use in the estuaries of the Gulf of Mexico (GOM). Remote-sensing reflectance (Rrs) at 645 nm and 250-m resolution was validated with in-situ turbidity measurements in these estuaries: Coastal Bend Bays (TX), Galveston Bay (TX), Barataria and Terrebonne Bays (LA), Mobile Bay (AL), Tampa Bay (FL), Sarasota Bay (FL), and Charlotte Harbor (FL). Mean values of turbidity over the time-series ranged from 2.5 NTU to over 10 NTU. Turbidity patterns exhibited seasonal cycles with peak values generally found during spring months, although there is considerable variability in the timing of peak turbidity. Episodes of elevated turbidity ranged from 6 episodes in Galveston Bay to 15 in Mobile Bay. The spatial extent of elevated turbidity within estuaries, frequency and duration of turbidity events, and potential driving factors behind episodes of elevated turbidity were also examined.

Microbiological and Chemical Findings of Water Used for Various Industrial Processes in Babol Car Factory, Iran, in 2013 A Case Study

Directory of Open Access Journals (Sweden)

Saeid Mahdavi Omran

2015-03-01

Full Text Available Abstract Background and purpose: According to the reported problems in area of the inappropriateness of water quality which used for washing and staining of car apparatuses in a car factory, this research was carried out for identification of physical, chemical, and microbiological characteristics of the consumed water in Babol car factory, Iran. Materials and Methods: Physical and chemical parameters of water such as total solids, total dissolved solids (TDS, turbidity, pH, electrical conductivity, total alkalinity, total hardness (TH, cations (Ca2+, Mg2+, Fe2+, Mn2+, Zn2+, and anions (SO42−, Cl−, NO3− were analyzed based on standard methods for examination of water and wastewater. The samples were taken from five units and were precipitated and plated on Sabouraud dextrose agar supplemented with chloramphenicol and blood agar and eosin methylene blue media. Results: TDS, turbidity, pH, TH and ammonium ion were 402 mg/L, 10 NTU, 7.8, 208 mg/L and 0.04 mg/L, respectively. Ten genera of fungal colonies were isolated from these units, which from them yeast Penicillium and Cladosporium were the most prevalent. Five genera of bacteria were isolated from these samples. Entrobacteriaceae, Pseudomonas, and Bacillus were the most prevalent bacteria in water. Water quality in the activation and fixation units were the most contaminated with fungi and bacteria, respectively. Some of these units were without fungal and bacterial contaminations. Conclusion: The fungal and bacterial contaminations can be changed the quality of consumed water in the different processes such as color and turbidity. Thus, we need to use some water

BRAND LOYALTY OF FEMALE CONSUMERS - STUDY CARRIED IN SFÂNTU GHEORGHE AND THE SURROUNDING AREAS

Directory of Open Access Journals (Sweden)

Erika KULCSÁR

2011-01-01

Full Text Available Today, the role of women in society has significantly changed, they work as men so they have their own income that they can spend as they wish and as necessary. We need to pay particular importance to consumer behaviour of female and as such it should be treated as a particular segment. This paper aims to study the simultaneous effects - based on data from quantitative marketing research – that the independent variables generate on the dependent variable. The variables introduced in the analysis of variance are: How often do you drink coffee /tea every day?, Age, Income, Last graduated school. We applied the hi square test we in order to analyze the links between two variables measured with nominal scale. The variables analyzed are: Do you always buy the some brand and The highest level of education achieved.

Electronic Structure and Bonding Situation in M2O2 (M=Be,Mg,Ca) Rhombic Clusters.

Czech Academy of Sciences Publication Activity Database

Li, W.-L.; Lu, J.-B.; Zhao, L.; Ponec, Robert; Cooper, D.L.; Li, J.; Frenking, G.

Roč. 122, č. 10 ( 2018 ), s. 2816-2822 ISSN 1089-5639 Grant - others:NNSFCH(CN) 21590792; NNSFCH(CN) 21433005; NNSFCH(CN) 21703099; JPY NSF(CN) BK20170964; NTU(CN) 39837123 Institutional support: RVO:67985858 Keywords : electronic structures * M2O2n clustery * theoretical isnights Subject RIV: CF - Physical ; Theoretical Chemistry OBOR OECD: Physical chemistry Impact factor: 2.847, year: 2016

2632-IJBCS-Article-Cheikhou Kane

African Journals Online (AJOL)

hp

final pH ranging from 6 to 9 for water discharge or reuse in washing vehicles for example. Bhuptawat and Folkard (2007), with aqueous extraction of the bioactive component of. Moringa oleifera, treated a wastewater with initial turbidity of 13.5 NTU and 150 mg/L of COD and. pH=7.2. The results indicated that by using the.

State-space modelling for the ejector-based refrigeration system driven by low grade energy

International Nuclear Information System (INIS)

Xue, Binqiang; Cai, Wenjian; Wang, Xinli

2015-01-01

This paper presents a novel global state-space model to describe the ejector-based refrigeration system, which includes the dynamics of the two heat exchangers and the static properties of ejector, compressor and expansion valve. Different from the existing methods, the proposed method introduces some intermediate variables into the dynamic modelling in developing reduced order models of the heat exchangers (evaporator and condenser) based on the Number of Transfer Units (NTU) method. This global model with fewer dimensions is much simpler and can be more convenient for the real-time control system design, compared with other dynamic models. Finally, the proposed state-space model has been validated by dynamic response experiments on the ejector-based refrigeration cycle with refrigerant R134a.The experimental results indicate that the proposed model can predict well the dynamics of the ejector-based refrigeration system. - Highlights: • A low-order state-space model of ejector-based refrigeration system is presented. • Reduced-order models of heat exchangers are developed based on NTU method. • The variations of mass flow rates are introduced in multiple fluid phase regions. • Experimental results show the proposed model has a good performance

Validation of a FAST Model of the SWAY Prototype Floating Wind Turbine

Energy Technology Data Exchange (ETDEWEB)

Koh, J. H. [Nanyang Technological Univ. (Singapore); Ng, E. Y. K. [Nanyang Technological Univ. (Singapore); Robertson, Amy [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jonkman, Jason [National Renewable Energy Lab. (NREL), Golden, CO (United States); Driscoll, Frederick [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-06-01

As part of a collaboration of the National Renewable Energy Laboratory (NREL) and SWAY AS, NREL installed scientific wind, wave, and motion measurement equipment on the spar-type 1/6.5th-scale prototype SWAY floating offshore wind system. The equipment enhanced SWAY's data collection and allowed SWAY to verify the concept and NREL to validate a FAST model of the SWAY design in an open-water condition. Nanyang Technological University (NTU), in collaboration with NREL, assisted with the validation. This final report gives an overview of the SWAY prototype and NREL and NTU's efforts to validate a model of the system. The report provides a summary of the different software tools used in the study, the modeling strategies, and the development of a FAST model of the SWAY prototype wind turbine, including justification of the modeling assumptions. Because of uncertainty in system parameters and modeling assumptions due to the complexity of the design, several system properties were tuned to better represent the system and improve the accuracy of the simulations. Calibration was performed using data from a static equilibrium test and free-decay tests.

Extraction of natural coagulant from peanut seeds for treatment of turbid water

International Nuclear Information System (INIS)

Birima, A H; Desa, M N M; Muda, Z C; Hammad, H A

2013-01-01

This study investigates the potential of peanut seeds as an environmental friendly and natural coagulant for the treatment of high turbid water. The peanut seeds have been used after oil extraction; and the active coagulation component was extracted by distilled water and salt solution of different salt concentrations. The salts used were NaCl, KNO 3 , KCl, NH 4 Cl and NaNO 3 . Synthetic water with 200 NTU turbidity was used. Peanut extracted with NaCl (PC-NaCl) could effectively remove 92% of the 200 NTU turbidity using only 20 mg/l, while peanut seeds extracted with distilled water (PC-DW) could remove only 31.5% of the same turbidity with the same dosage. The coagulant dosage did not affected by the concentration of the salt solution, however, residual turbidity decreased with increasing the concentration of the salt; and the relationship was found to be a second order polynomial curve with R 2 of 0.9312. The other salts tested were also found to be good solvents to extract the active coagulation component with no much difference from NaCl solution in terms of efficiency.

Intra-annual variation in turbidity in response to terrestrial runoff on near-shore coral reefs of the Great Barrier Reef

Science.gov (United States)

Fabricius, Katharina E.; De'ath, Glenn; Humphrey, Craig; Zagorskis, Irena; Schaffelke, Britta

2013-01-01

Seawater turbidity is a fundamental driver of the ecology of coastal marine systems, and is widely used as indicator for environmental reporting. However, the time scales and processes leading to changes in turbidity in tropical coastal waters remain poorly understood. This study investigates the main determinants of inshore turbidity in four inshore regions along ˜1000 km of the Australian Great Barrier Reef, based on ˜3 years of almost continuous in situ turbidity logger data on 14 reefs. Generalized additive mixed models were used to predict spatial and temporal variation in weekly mean turbidity based on variation in resuspension and runoff conditions. At any given wave height, wave period and tidal range, turbidity was significantly affected by river flow and rainfall. Averaged across all reefs, turbidity was 13% lower (range: 5-37%) in weeks with low compared with high rainfall and river flows. Additionally, turbidity was on average 43% lower 250 days into the dry season than at the start of the dry season on reefs with long-term mean turbidity >1.1 NTU. The data suggest the time scale of winnowing or consolidation of newly imported materials in this zone is months to years. In contrast, turbidity returned to low levels within weeks after river flows and rainfall on reefs with long-term mean turbidity of <1.1 NTU. Turbidity was also up to 10-fold higher on reefs near compared to away from river mouths, suggesting inter-annual accumulation of fine resuspendible sediments. The study suggests that a reduction in the river loads of fine sediments and nutrients through improved land management should lead to measurably improved inshore water clarity in the most turbid parts of the GBR.

On the optimum performance of forced draft counter flow cooling towers

International Nuclear Information System (INIS)

Soeylemez, M.S.

2004-01-01

A thermo-hydraulic performance optimization analysis is presented, yielding simple algebraic formula for estimating the optimum performance point of counter current mechanical draft wet cooling towers. The effectiveness-Ntu method is used in the present study, together with the derivation of psychometric properties of moist air based on a numerical approximation method, for thermal performance analysis of wet cooling towers of the counter flow type

Ultraviolet Light Disinfection in the Use of Individual Water Purification Devices

Science.gov (United States)

2006-03-01

adenovirus, Giardia lamblia, Giardia muris , and Cryptosporidium parvum. Adenovirus was evaluated because it is considered the most resistant to...7 reproduce cannot infect and are thereby inactivated. Subsequently, when evaluating UV disinfection capability, Giardia cyst and...0.25 to 20 NTU resulted in a 0.8-log and 0.5-log decrease in inactivation of Cryptosporidium and Giardia , respectively (reference 3). The type of

Turbidity data: Hollywood Beach, Florida, January 1990 to April 1992

OpenAIRE

Dompe, Philip E.; Hanes, D. M.

1993-01-01

This data report contains measurements of turbidity obtained near Hollywood, Florida, during the period of January 1990 to April 1992. Data were obtained within one meter of the seabed in depths of 5 m and 10 m. Turbidity was found to vary significantly under natural conditions, with values during storms sometimes exceeding 29 NTU. Tables and plots of turbidity data are presented. (Document contains 77 pages.)

Introduction to the theory of cooperative games

CERN Document Server

Peleg, Bezalel; Peleg, Bezalel

2007-01-01

This book systematically presents the main solutions of cooperative games: the core, bargaining set, kernel, nucleolus, and the Shapley value of TU games as well as the core, the Shapley value, and the ordinal bargaining set of NTU games. The authors devote a separate chapter to each solution, wherein they study its properties in full detail. In addition, important variants are defined or even intensively analyzed.

Application of Moringa oleifera Seed in Removing Colloids from Turbid Wastewater

OpenAIRE

H. Zemmouri; H. Lounic; N. Mameri

2015-01-01

The present study aims to investigate the performance of Moringa oleifera seed extract as natural coagulant in clarification of secondary wastewater treatment plant (MWWTP) located in East of Algiers, Algeria. Coagulation flocculation performance of Moringa oleifera was evaluated through supernatant residual turbidity after jar test trials. Various influence parameters namely Moringa oleifera dosage and pH have been considered. Tests on Reghaia wastewater, having 129 NTU ...

Sediment-induced turbidity impairs foraging performance and prey choice of planktivorous coral reef fishes.

Science.gov (United States)

Johansen, J L; Jones, G P

2013-09-01

Sedimentation is a substantial threat to aquatic ecosystems and a primary cause of habitat degradation on near-shore coral reefs. Although numerous studies have demonstrated major impacts of sedimentation and turbidity on corals, virtually nothing is known of the sensitivity of reef fishes. Planktivorous fishes are an important trophic group that funnels pelagic energy sources into reef ecosystems. These fishes are visual predators whose foraging is likely to be impaired by turbidity, but the threshold for such effects and their magnitude are unknown. This study examined the effect of sediment-induced turbidity on foraging in four species of planktivorous damselfishes (Pomacentridae) of the Great Barrier Reef, including inshore and offshore species that potentially differ in tolerance for turbidity. An experimental flow tunnel was used to quantify their ability to catch mobile and immobile planktonic prey under different levels of turbidity and velocity in the range encountered on natural and disturbed reefs. Turbidity of just 4 NTU (nephelometric turbidity units) reduced average attack success by up to 56%, with higher effect sizes for species with offshore distributions. Only the inshore species (Neopomacentrus bankieri), which frequently encounters this turbidity on coastal reefs, could maintain high prey capture success. At elevated turbidity similar to that found on disturbed reefs (8 NTU), attack success was reduced in all species examined by up to 69%. These reductions in attack success led to a 21-24% decrease in foraging rates for all mid to outer-shelf species, in spite of increasing attack rates at high turbidity. Although effects of turbidity varied among species, it always depended heavily on prey mobility and ambient velocity. Attack success was up to 14 times lower on mobile prey, leaving species relatively incapable of foraging on anything but immobile prey at high turbidity. Effects of turbidity were particularly prominent at higher velocities, as

Gravity filtration performances of the bio-diatomite dynamic membrane reactor for slightly polluted surface water purification.

Science.gov (United States)

Chu, Huaqiang; Dong, Bingzhi; Zhang, Yalei; Zhou, Xuefei

2012-01-01

A bio-diatomite dynamic membrane (BDDM) reactor for surface water treatment under a water head of 30, 40, 50, 60 and 70 cm, respectively, was investigated, which was very effective for pollutants removal. The water head exerted strong influences on filtration flux of BDDM during the precoating process, as well as on the formation of BDDM and turbidity variations. A high filtration flux (approximately 200-300 L/m2 h) could be achieved in the long filtration times of BDDM with a stable effluent turbidity of approximately 0.11-0.25 NTU. The BDDM could remove particles larger than 25 μm completely. The adopted sintered diatomite mainly consisted of macro pores, which were beneficial for improving the filtration flux of BDDM. During the backwash stage, the BDDM could be removed completely by the air backwash.

Evaluation of regenerative phase change drywalls: low-energy building application

Energy Technology Data Exchange (ETDEWEB)

Darkwa, K. [Nottingham Trent Unv., Applied Energy and Environmental Engineering Unit, Nottingham (United Kingdom)

1999-07-01

An integrated phase change drywall system has been analytically evaluated for low-energy building applications. The mathematical model indicates that it is possible to attain higher levels of thermal performance and efficiency with lower values of transfer units (NTU). Even though the model does not take into account the variable nature of the thermophysical properties of phase change materials (PCMs), reasonable thermal performance is achievable. Experimental validation is therefore recommended. (Author)

Effectiveness of inorganic membrane mixture of natural zeolite and portland white cement in purifying of peat water based on turbidity parameter

Science.gov (United States)

Elfiana; Fuadi, A.; Diana, S.

2018-04-01

Peat water is water surface that brownish red colour caused by the contained constituents. Solving the peat watercolor problem requires special attention considering the quantity of peat water and suitable to be used to meet the daily needs. This study aims to know the inorganic membrane capability of mix nature zeolite and white Portland cement to purifying the peat water based on turbidity parameter. The study was conducted by varying the composition of nature zeolite (Za) and white Portland cement (Sp) in the ratio of Za: Sp is (25%:75%; 50%:50%; 75%:25%) with zeolite condition activated using HCl 2M and nonactivated zeolite treatments. The result of the characteristic test on membrane morphology using SEM (Scanning Electron Microscope) showed that the pore surface size of the membrane is 2 μm that could classified in microfiltration membrane an organic type. The characteristic test showed also resulted in the density of 0.77 to 0.86 gr/cm3, porosity 26.22% to 35.93%, and permeability 2736.19 to 8428.15. While the water retention capacity is in range of 30.64% to 46.46%, The result of inorganic membrane application on peat water showed turbidity of peat water decreased 94.17%, from 10.3 NTU to 0.6 NTU.

The design of rapid turbidity measurement system based on single photon detection techniques

Science.gov (United States)

Yang, Yixin; Wang, Huanqin; Cao, Yangyang; Gui, Huaqiao; Liu, Jianguo; Lu, Liang; Cao, Huibin; Yu, Tongzhu; You, Hui

2015-10-01

A new rapid turbidity measurement system has been developed to measure the turbidity of drinking water. To determinate the turbidity quantitatively, the total intensity of scattering light has been measured and quantified as number of photons by adopting the single photon detection techniques (SPDT) which has the advantage of high sensitivity. On the basis of SPDT, the measurement system has been built and series of experiments have been carried out. Combining then the 90° Mie scattering theory with the principle of SPDT, a turbidity measurement model has been proposed to explain the experimental results. The experimental results show that a turbidity, which is as low as 0.1 NTU (Nephelometric Turbidity Units), can be measured steadily within 100 ms. It also shows a good linearity and stability over the range of 0.1-400 NTU and the precision can be controlled within 5% full scale. In order to improve its precision and stability, some key parameters, including the sampling time and incident light intensity, have been discussed. It has been proved that, to guarantee an excellent system performance, a good compromise between the measurement speed and the low power consumption should be considered adequately depending on the practical applications.

Limnological Studies of Keenjhar Lake, District, Thatta, Sindh, Pakistan.

Directory of Open Access Journals (Sweden)

K. H. Lashari, , and

2009-12-01

Full Text Available Limnological studies of Keenjhar Lake were carried out during January 2003 to December 2005. The present study deals with physico - chemical parameters such as, temperature, pH, alkalinity, chlorides, conductivity, total dissolve solids, turbidity, dissolve oxygen, calcium and magnesium. The maximum and minimum range of physico - chemical properties were as, temperature 18 - 33 ⁰C from station 2 in January and August respectively, pH 7.3 - 8.9 in September and June respectively, alkalinity 160 - 240 mg L-1 in July and January respectively, minimum chlorides 30 mg L-1 in September and maximum 85 mg L-1 in December, conductivity 320 S cm-1 in September and 496 S cm-1 in December, total dissolve solids were 240 mg L-1 in September and 391 mg L-1 in October, turbidity was 30 NTU in December and 78 NTU in May, dissolve oxygen was 7.0 mg L-1 in January and 9.0 mg L-1 in July, calcium 50 mg L-1 in July and September and 78 mg L-1 in October, magnesium 21 mg L-1 in August and September, 35 mg L-1 June, and it is concluded that the variation in parameters were due to rain and flow of River Indus.

Additive negative effects of anthropogenic sedimentation and warming on the survival of coral recruits.

Science.gov (United States)

Fourney, Francesca; Figueiredo, Joana

2017-09-28

Corals worldwide are facing population declines due to global climate change and local anthropogenic impacts. Global climate change effects are hard to tackle but recent studies show that some coral species can better handle climate change stress when provided with additional energy resources. The local stressor that most undermines energy acquisition is sedimentation because it impedes coral heterotrophic feeding and their ability to photosynthesize. To investigate if reducing local sedimentation will enable corals to better endure ocean warming, we quantitatively assessed the combined effects of increased temperature and sedimentation (concentration and turbidity) on the survival of coral recruits of the species, Porites astreoides. We used sediment from a reef and a boat basin to mimic natural sediment (coarse) and anthropogenic (fine) sediment (common in dredging), respectively. Natural sediment did not negatively impact coral survival, but anthropogenic sediment did. We found that the capacity of coral recruits to survive under warmer temperatures is less compromised when anthropogenic sedimentation is maintained at the lowest level (30 mg.cm -2 ). Our study suggests that a reduction of US-EPA allowable turbidity from 29 Nephelometric Turbidity Units (NTU) above background to less than 7 NTU near coral reefs would facilitate coral recruit survival under current and higher temperatures.

Turbidity in oil-in-water-emulsions - Key factors and visual perception.

Science.gov (United States)

Linke, C; Drusch, S

2016-11-01

The aim of the present study is to systematically describe the factors affecting turbidity in beverage emulsions and to get a better understanding of visual perception of turbidity. The sensory evaluation of the human visual perception of turbidity showed that humans are most sensitive to turbidity differences between two samples in the range between 1000 and 1500 NTU (ratio) (nephelometric turbidity units). At very high turbidity values >2000 TU in NTU (ratio) were needed to distinguish between samples that they were perceived significantly different. Particle size was the most important factor affecting turbidity. It was shown that a maximum turbidity occurs at a mean volume - surface diameter of 0.2μm for the oil droplet size. Additional parameters were the refractive index, the composition of the aqueous phase and the presence of excess emulsifier. In a concentration typical for a beverage emulsion a change in the refractive index of the oil phase may allow the alteration of turbidity by up to 30%. With the knowledge on visual perception of turbidity and the determining factors, turbidity can be tailored in product development according to the customer requirements and in quality control to define acceptable variations in optical appearance. Copyright © 2016. Published by Elsevier Ltd.

The Effect of Organic Loading Rate on Milk WastewaterTreatment Using Sequencing Batch Reactor (SBR

Directory of Open Access Journals (Sweden)

Hooman Hajiabadi

2009-09-01

Full Text Available In this study, four aerobic sequencing batch reactors (SBRs were operated under the same conditions for the treatment of milk wastewater at different organic loading rates (OLRs. Cylindrical Plexiglas reactors were run for 56 days (including 21 days of acclimatization and 35 days of data gathering. Effective volume, influent wastewater flowrate, and sludge retention time (SRT of reactors were 5.5 L, 3.5 L/d, and 10 d, respectively. The average COD removal efficiency for the reactors R1, R2, R3, and R4 with influent OLRave values of 633, 929, 1915, and 3261 gCOD/m3d were 95, 96, 95, and 82 percent, respectively. The average effluent suspended solid (SS for all reactors was lower than 44 mg/L. Also, except for R4 with an average effluent turbidity of 270 NTU, other reactors met the Iranian wastewater emission standard (50 NTU. In addition, the average sludge volume index of reactors R1 to R3 was found to be lower than 67 mL/g. According to the results, the overall variation of COD removal efficiency versus influent OLR shows a decreasing rate with a correlation factor of 0.8 (R2.

Comparison of desiccant air conditioning systems with different indirect evaporative air coolers

International Nuclear Information System (INIS)

Pandelidis, Demis; Anisimov, Sergey; Worek, William M.; Drąg, Paweł

2016-01-01

Highlights: • A numerical study of desiccant air conditioning systems is presented. • The ε-NTU model is used for the analysis. • Different arrangements of the desiccant systems were compared. • The systems were compared under different operating conditions. - Abstract: This paper presents a numerical analysis of three desiccant air-conditioning systems equipped with different indirect evaporative air coolers: (1) the cross-flow Maisotsenko cycle heat and mass exchanger (HMX), (2) the regenerative counter-flow Maisotsenko cycle heat and mass exchanger and (3) the standard cross-flow evaporative air cooler. To analyze the desiccant wheel and the indirect evaporative air coolers, the modified ε-NTU-model was used. The simulations were performed under assumption that the desiccant wheel is regenerated with air heated to relatively low temperature values (50–60 °C), which can be produced with solar panels in typical moderate climatic conditions. It was established that the main advantage of the presented solutions is that they can provide comfort conditions even with less effective dehumidification. The different systems were compared under variable selected operational factors (i.e. inlet air temperature, humidity and regeneration air temperature). The analysis allowed establishing the advantages and disadvantages of presented solutions and allowed estimating their application potential.

TESTING AND EVALUATION OF THE MODIFIED DESIGN OF THE 25-DISK ROTARY MICROFILTER

International Nuclear Information System (INIS)

Herman, D; Michael Poirier, M; Samuel Fink, S

2006-01-01

% insoluble solids with no operational problems with the exception of the entrainment of air due to leaking packing in the feed pump. Prior to the air entrainment, the filtration rate was approximately 4.2 gpm for one filter assembly with the process fluid temperature adjusted to 35 C. Personnel measured the turbidity of filtrate samples from all phases of testing. All samples measured were less than 3 NTU, with the majority of samples less than 1 NTU. Thus, all measurements fell below the process acceptance criterion of less than 5 NTU. After slurry operations, personnel rinsed the filter with the equivalent of 250 gallons of water by re-circulating 50 gallons of water. The residual sludge solids remaining on the filter stack weighed approximately 685 grams. This amount of solids corresponds to an equivalent activity of 15.1 curies (Ci) beta and 0.38 Ci gamma radiation dose for Sludge Batch 4. Workers completely disassembled the filter system and examined it for signs of wear and component operation. An evaluation by a John Crane Inc. representative concluded that the wear observed on the mechanical seal resulted primarily from the numerous stops and starts, the abrasive nature of the process fluid and the possibility that the seal faces did not receive enough lubrication from the process fluid. No measurable slurry bypassed the mechanical seal. While it is extremely difficult to predict the life of the seal, the vendor representative indicates a minimum of one year in present service is reasonable. Changing the seal face material from silicon-carbide to a graphite-impregnated silicon-carbide is expected to double the life of the seal. Replacement with an air seal might be expected to increase lifetime to five years. The bottom bushing showed wear due to a misalignment during the manufacture of the filter tank. Minor adjustments to the alignment with shims and replacement of the graphite bushing with a superior material will greatly reduce this wear pattern

Treatment of waste water by coagulation and flocculation using biomaterials

Science.gov (United States)

Muruganandam, L.; Saravana Kumar, M. P.; Jena, Amarjit; Gulla, Sudiv; Godhwani, Bhagesh

2017-11-01

The present study deals with the determination of physical and chemical parameters in the treatment process of waste water by flocculation and coagulation processes using natural coagulants and assessing their feasibility for water treatment by comparing the performance with each other and with a synthetic coagulant. Initial studies were done on the synthetic waste water to determine the optimal pH and dosage, the activity of natural coagulant, followed by the real effluent from tannery waste. The raw tannery effluent was bluish-black in colour, mildly basic in nature, with high COD 4000mg/l and turbidity in the range 700NTU, was diluted and dosed with organic coagulants, AloeVera, MoringaOleifera and Cactus (O.ficus-indica). The study observed that coagulant Moringa Oleifera of 15 mg/L dose at 6 pH gave the best reduction efficiencies for major physicochemical parameters followed by Aloe Vera and Cactus under identical conditions. The study reveals that the untreated tannery effluents can be treated with environmental confirmative naturally occurring coagulants.

EFECTO DE LA Moringa oleífera EN EL TRATAMIENTO DE AGUAS RESIDUALES EN EL CAUCA, COLOMBIA

Directory of Open Access Journals (Sweden)

CARLOS FERNANDO MERA ALEGRIA

2016-11-01

Full Text Available Effect moringa seed powder and natural flocculant and coagulant in sewage treatment, it was assessed process waters resulting coffee mill were used more than 2000 NTU turbidity and water from the chemical peeling vegetables 91,5 Nephelometric turbidity units (UNT. Treatments were performed using the test jar at 130 revolutions/minute at 21,5°C temperature with agitation time of 30 minutes to wastewater coffee mill waters and 15 minutes for chemical peeling vegetables. To determine water quality was evaluated: turbidity, pH, electrical conductivity, chlorides, suspended solids, total coliforms and fecal supernatant; comparison with aluminum sulfate using the same dosing was performed, the results indicate that using 4 g/600 mL of wastewater coffee processing efficiency of 80,9% and 73,5% was obtained with moringa seed powder and sulfate using aluminum respectively and 0,15 g/600 mL water chemical peeling vegetable efficiency of 66,75% with Moringa had and aluminum sulfate 63,5%; stating that the moringa seed powder is more effective in improving the various parameters established in the investigation.

Improvement of water treatment pilot plant with Moringa oleifera extract as flocculant agent.

Science.gov (United States)

Beltrán-Heredia, J; Sánchez-Martín, J

2009-05-01

Moringa oleifera extract is a high-capacity flocculant agent for turbidity removal in surface water treatment. A complete study of a pilot-plant installation has been carried out. Because of flocculent sedimentability of treated water, a residual turbidity occured in the pilot plant (around 30 NTU), which could not be reduced just by a coagulation-flocculation-sedimentation process. Because of this limitation, the pilot plant (excluded filtration) achieved a turbidity removal up to 70%. A slow sand filter was put in as a complement to installation. A clogging process was characterized, according to Carman-Kozeny's hydraulic hypothesis. Kozeny's k parameter was found to be 4.18. Through fouling stages, this k parameter was found to be up to 6.36. The obtained data are relevant for the design of a real filter in a continuous-feeding pilot plant. Slow sand filtration is highly recommended owing to its low cost, easy-handling and low maintenance, so it is a very good complement to Moringa water treatment in developing countries.

Subcomponents and Connectivity of the Inferior Fronto-Occipital Fasciculus Revealed by Diffusion Spectrum Imaging Fiber Tracking

OpenAIRE

Wu, Yupeng; Sun, Dandan; Wang, Yong; Wang, Yibao

2016-01-01

The definitive structure and functional role of the inferior fronto-occipital fasciculus (IFOF) are still controversial. In this study, we aimed to investigate the connectivity, asymmetry, and segmentation patterns of this bundle. High angular diffusion spectrum imaging (DSI) analysis was performed on 10 healthy adults and a 90-subject DSI template (NTU-90 Atlas). In addition, a new tractography approach based on the anatomic subregions and two regions of interest (ROI) was evaluated for the ...

The Rare Earth Collision: A Hit and Run on the Third Offset Strategy

Science.gov (United States)

2017-03-29

2016) 62 Ibid. 63 Filip Karinja, “Sinosteel MECC Selected by Northern Minerals as EPC Contractor for Browns Range Pilot Plant,” http://finfeed.com...juniors/ntu/sinosteel-mecc-selected-northern-minerals-epc- contractor - browns-range-pilot-plant/20161123/ (accessed November 25, 2016). 64 Andrew Topf...the_fallacies_of_the_third_offset_strategy_109668. ht ml (accessed October 2, 2016). Dr. Andrew Davies, formally of the Australian Department of Defense, is the current Director

adaptation et selection de varietes performantes de riz pluvi

African Journals Online (AJOL)

PROJET SOJA

Ces matières en suspension (MES) sont essentiellement argileuses et contiennent des éléments métalliques. Environ 17,5 μg.g-1 de cadmium ont été mesurés dans ces MES. Le milieu aquatique récepteur est très turbide (environ 200 NTU). L'étude ne montre pas une contamination particulière du poisson par les métaux ...

Removal of COD and turbidity to improve wastewater quality using electrocoagulation technique

International Nuclear Information System (INIS)

Mohd Faiqun Niam; Fadil Othman; Johan Sohaili; Zulfa Fauzia

2007-01-01

Electrocoagulation (EC) is becoming a popular process to be used for wastewater treatment. The removal of COD and turbidity from wastewater by EC using iron (Fe) electrode material was investigated in this paper. Several working parameters, such as pH, current density, and operating time were studied in an attempt to achieve a higher removal capacity. Wastewater sample was made from milk powder with initial COD of 1140 mgL -1 and turbidity of 491 NTU. Current density was varied from 3.51 to 5.62 mA cm -2 , and operating time of between 30 and 50 minutes. The results show that the effluent wastewater was very clear and its quality exceeded the direct discharge standard. The removal efficiencies of COD and turbidity were high, being more than 65 % and 95 %. In addition, the experimental results also show that the electrocoagulation can neutralize pH of wastewater. (author)

Design of a tubular ceramic membrane for gas separation in a PEMFC system

Energy Technology Data Exchange (ETDEWEB)

Kamarudin, S.K.; Daud, W.R.W.; Mohammad, A.W.; Som, A.Md.; Takriff, M.S. [Department of Chemical and Process Engineering, National University of Malaysia, 43600 UKM Bangi, Selangor (Malaysia)

2004-01-01

The objective of this study is to introduce a shortcut in the method of design for a tubular ceramic membrane (TCM) for gas separation. Generally, it explains the permeation of the multi component gas using cross flow models in a porous membrane and the surface area of the membrane required. The novel aspect of this method is that the expression for the length of the membrane is simplified to a number unit (NTU) and a height of transfer unit (HTU). The HTU term for porous membranes is characterised by the physical properties of the membrane; the feed flow rate, n{sub F}, membrane thickness, l{sub M}, feed pressure, P{sub F}, K the permeability of gas and the diameter of the membrane, D{sub M}. The integral for NTU of a porous membrane is the solution for the local permeate along the length of the membrane. It is found that, NTU mainly depends on the rejection stream, x{sub R,}, along the membrane and it describes the relative degree of separation. The Proton Electrolyte Membrane Fuel Cell (PEMFC) system is taken as the case study. CO is the main culprit in reducing the performance of the PEMFC and will act as a catalyst poison for the fuel cell anode at a concentration as low as 100 ppm. Thus, the reformate, from primary reforming, contains a significant amount of CO and must be purified. The effect of some important parameters such as temperature, pressure and the thickness of membrane to the degree of separation are presented in this paper. From the results, it can be seen that the system could reduce the CO concentration from 2000 - 500 ppm. Basically the TCM will operate, in series, with a pressure swing adsorber in order to further reduce the concentration of CO to less than 10 ppm before entering the fuel cell stack. However, this paper only focuses on the design of the TCM. Besides this, it is observed that the purity of the hydrogen increased from 72.8 - 96% (at {theta} = 0.5) after the membrane. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Supporting Data for FY 1990/1991 Biennial Budget: Budget Estimates Descriptive Summaries Submitted to Congress January 1989, Research, Development, Test & Evaluation, Navy

Science.gov (United States)

1989-01-01

Title: P-3 gpdate IV Avi nics E. (U) COMPARISCN WITH AMENDED FY 1988/1989 DESCRIPTIVE SUHMARY: IMPACT OF CHANGES TYPE OF impact on Impact on Impact on...d. (U) Completed NTU TEMP 547 DT/OT-IIIA testing aboard USS BIDDLE (OG-34). e. (U) Initiated engineering design/development of modifications to...with the Royal and Royal Australian Navies for delivery of OBU under Foreign Military Sales (FMS) provisions. J. (U) TEST AND EVALUATION DATA: NIC /DIA

Optimization of GaN Nanorod Growth Conditions for Coalescence Overgrowth

Science.gov (United States)

2016-02-04

21, 2016 PI: Chih-Chung (C. C.) Yang, ccycc@ntu.edu.tw Graduate Institute of Photonics and Optoelectronics, National Taiwan University...nanowire light emitting diodes grown on (001) silicon by molecular beam epitaxy, Nano Lett. 10 (2010) 3355-3359. [16] W. Guo, A. Banerjee, P...Bhattacharya, B.S. Ooi, InGaN/GaN disk-in-nanowire white light emitting diodes on (001) silicon , Appl. Phys. Lett. 98 (2011) 193102. [17] H.P.T. Nguyen, M

Thermal performance modeling of cross-flow heat exchangers

CERN Document Server

Cabezas-Gómez, Luben; Saíz-Jabardo, José Maria

2014-01-01

This monograph introduces a numerical computational methodology for thermal performance modeling of cross-flow heat exchangers, with applications in chemical, refrigeration and automobile industries. This methodology allows obtaining effectiveness-number of transfer units (e-NTU) data and has been used for simulating several standard and complex flow arrangements configurations of cross-flow heat exchangers. Simulated results have been validated through comparisons with results from available exact and approximate analytical solutions. Very accurate results have been obtained over wide ranges

The effect of wastewater pretreatment on nanofiltration membrane performance

Directory of Open Access Journals (Sweden)

Ali Hashlamon

2017-03-01

Full Text Available Membrane fouling is considered a serious obstacle for operation and cost efficiency in wastewater treatment using nanofiltration (NF. However, pretreatment is the most practical way to reduce this prior to NF. In this research, two types of wastewaters were pretreated with different methods prior to NF to examine the effect of pretreatment on membrane fouling in terms of turbidity, chemical oxygen demand (COD and permeate flux. Turbidity and COD were measured to assess solid foulants and organic species in the wastewater, respectively. The first sample was secondary treated sewage, which was pretreated using coagulation-flocculation-sedimentation (CFS only. Steady flux was increased from 24 L/m2h for wastewater without pretreatment to 32.1 L/m2h with pretreatment. COD was also eliminated after CFS/NF, and turbidity was reduced to 0.6 NTU. The second sample was diluted biodiesel wastewater, which was pretreated using a combination of powdered-activated carbon (PAC adsorption and CFS (PAC/CFS. Steady flux was increased from 22.3 L/m2h for wastewater without pretreatment to 28.7 L/m2h with pretreatment; biodiesel wastewater quality also improved. Turbidity was reduced from 12 to 0.6 NTU, and COD was reduced from 526 to 4 mg/L after NF with PAC/CFS pretreatment, while COD was reduced from 526 to 95 mg/L using NF without pretreatment.

Analisis Kualitas Perairan Pada Wilayah Perairan Pulau Serangan Bagian Utara Berdasarkan Baku Mutu Air Laut

Directory of Open Access Journals (Sweden)

Ni Luh Gede Rai Ayu Saraswati

2017-06-01

Full Text Available Water quality monitoring is one of important activity, especially in coastal water, which susceptive with pollution. Water area of Serangan Island is a tidal flat area, influenced by fresh water and sea water inputs. The existence activities, such as cage aquaculture and tourism, and input from river, are threatened to decrease the water quality in north of Serangan water. This research was conducted to the condition of water quality based on water quality standard for aquatic organisms and its spatial distribution. The parameters measured were temperature, salinity, pH, DO, turbidity, and BOD5, in 8 sample points. Some parameters measured directly on water surface (temperature, salinity, pH and DO and the others were analyzed in laboratory (turbidity, and BOD5. BOD5 was analyzed by standard method of Delzer & McKenzie. Based on research, the result of temperature values ranged from 28,9°C-30,5°C; salinity 29,6 ppt-32,7 ppt; pH 7,7-7,9; DO 3 mg/L-4,4 mg/L; turbidity 1,9 ntu-7,6 ntu; and BOD5 2,8 mg/L-5,4 mg/L. The water quality in Serangan had a different spatial distribution in each parameters. Overall, based on research result, the water quality condition in the body water of Serangan island was good and suitable to support aquatic organisms living.

Production of demineralized water for use in thermal power stations by advanced treatment of secondary wastewater effluent.

Science.gov (United States)

Katsoyiannis, Ioannis A; Gkotsis, Petros; Castellana, Massimo; Cartechini, Fabricio; Zouboulis, Anastasios I

2017-04-01

The operation and efficiency of a modern, high-tech industrial full-scale water treatment plant was investigated in the present study. The treated water was used for the supply of the boilers, producing steam to feed the steam turbine of the power station. The inlet water was the effluent of municipal wastewater treatment plant of the city of Bari (Italy). The treatment stages comprised (1) coagulation, using ferric chloride, (2) lime softening, (3) powdered activated carbon, all dosed in a sedimentation tank. The treated water was thereafter subjected to dual-media filtration, followed by ultra-filtration (UF). The outlet of UF was subsequently treated by reverse osmosis (RO) and finally by ion exchange (IX). The inlet water had total organic carbon (TOC) concentration 10-12 mg/L, turbidity 10-15 NTU and conductivity 3500-4500 μS/cm. The final demineralized water had TOC less than 0.2 mg/L, turbidity less than 0.1 NTU and conductivity 0.055-0.070 μS/cm. Organic matter fractionation showed that most of the final DOC concentration consisted of low molecular weight neutral compounds, while other compounds such as humic acids or building blocks were completely removed. It is notable that this plant was operating under "Zero Liquid Discharge" conditions, implementing treatment of any generated liquid waste. Copyright © 2016 Elsevier Ltd. All rights reserved.

The Impact on Tan Tock Seng Hospital’s Teaching Culture of Transforming into an Academic Health Centre

OpenAIRE

Tham, K. Y.

2016-01-01

Tan Tock Seng Hospital (TTSH), Singapore has a commendable “teaching culture” that teaches medical students well. The first research question is to understand how the teaching culture has been built in TTSH. In 2009 the Nanyang Technological University (NTU) invited TTSH to be its partner to start a new medical school, transforming TTSH into an academic health centre (AHC). The second research question is, “What is the impact on TTSH’s teaching culture of transforming into an AHC?” Qualitativ...

Improvement of extraction method of coagulation active components from Moringa oleifera seed

OpenAIRE

Okuda, Tetsuji; Baes, Aloysius U.; Nishijima, Wataru; Okada, Mitsumasa

1999-01-01

A new method for the extraction of the active coagulation component from Moringa oleifera seeds was developed and compared with the ordinary water extraction method (MOC–DW). In the new method, 1.0 mol l-1 solution of sodium chloride (MOC–SC) and other salts were used for extraction of the active coagulation component. Batch coagulation experiments were conducted using 500 ml of low turbid water (50 NTU). Coagulation efficiencies were evaluated based on the dosage required to remove kaolinite...

Caractérisation physico-chimique et diversité du peuplement ...

African Journals Online (AJOL)

L'identification et le dénombrement du phytoplancton ont été faits au microscope photonique de marque Nikon Eclipse 0,90 Dry. L'étude a révélé une turbidité, un pH et un taux d'oxygène dissous élevés dans les mares Afi et Lagoè avec des valeurs maximales de 8,25 NTU ; 8,14 et 9,75 mg/L. A Dindin, une conductivité ...

Bacterial, viral and turbidity removal by intermittent slow sand filtration for household use in developing countries: experimental investigation and modeling.

Science.gov (United States)

Jenkins, Marion W; Tiwari, Sangam K; Darby, Jeannie

2011-11-15

A two-factor three-block experimental design was developed to permit rigorous evaluation and modeling of the main effects and interactions of sand size (d(10) of 0.17 and 0.52 mm) and hydraulic head (10, 20, and 30 cm) on removal of fecal coliform (FC) bacteria, MS2 bacteriophage virus, and turbidity, under two batch operating modes ('long' and 'short') in intermittent slow sand filters (ISSFs). Long operation involved an overnight pause time between feeding of two successive 20 L batches (16 h average batch residence time (RT)). Short operation involved no pause between two 20 L batch feeds (5h average batch RT). Conditions tested were representative of those encountered in developing country field settings. Over a ten week period, the 18 experimental filters were fed river water augmented with wastewater (influent turbidity of 5.4-58.6 NTU) and maintained with the wet harrowing method. Linear mixed modeling allowed systematic estimates of the independent marginal effects of each independent variable on each performance outcome of interest while controlling for the effects of variations in a batch's actual residence time, days since maintenance, and influent turbidity. This is the first study in which simultaneous measurement of bacteria, viruses and turbidity removal at the batch level over an extended duration has been undertaken with a large number of replicate units to permit rigorous modeling of ISSF performance variability within and across a range of likely filter design configurations and operating conditions. On average, the experimental filters removed 1.40 log fecal coliform CFU (SD 0.40 log, N=249), 0.54 log MS2 PFU (SD 0.42 log, N=245) and 89.0 percent turbidity (SD 6.9 percent, N=263). Effluent turbidity averaged 1.24 NTU (SD 0.53 NTU, N=263) and always remained below 3 NTU. Under the best performing design configuration and operating mode (fine sand, 10 cm head, long operation, initial HLR of 0.01-0.03 m/h), mean 1.82 log removal of bacteria (98

Pretreatment of phosphoric acid of Annaba

International Nuclear Information System (INIS)

Kada, R.

1990-03-01

The most important step in the process of uranium recovery from phosphoric acid is the pretreatment operation. In this study, the adsorption of organic matters on activated carbon was carried out in a batch process and in a fixed bed column. First, the chemical and physical characterization of phosphoric acid, activated carbon and gypsum were performed. In addition, the organic matters were qualitatively analysed and a new and original quantitative method was experimented. Next, the various operating parameters such as agitation speed, granulometry, temperature, solid/liquid ratio, initial concentration, acid flowrate, and bed height were optimized. The experimental equilibrium isotherm was compared to the Langmuir, Freundlich, and Redlich-Peterson theoretical isotherms. It was noticed that the three models did not fit the experimental isotherm in the total concentration range. Thus, an original bilinear model was proposed. The influence of the operating conditions on the adsorption kinetics was also investigated. As a result of that, a new mathematical model was proposed to determine both the liquid and solid phases mass transfer and the solid phase diffusion coefficient. Finally, adsorption of organic matters on a fixed bed process allowed computation of the number of transfer units (NTU), the height of adsorption zone and the degree of saturation of activated carbon

Polyaluminium chloride as an alternative to alum for the direct filtration of drinking water.

Science.gov (United States)

Zarchi, Idit; Friedler, Eran; Rebhun, Menahem

2013-01-01

The efficiency of various polyaluminium chloride coagulants (PACls) was compared to the efficiency of aluminium sulfate (alum) in the coagulation-flocculation process preceding direct filtration in drinking water treatment. The comparative study consisted of two separate yet complementary series of experiments: the first series included short (5-7 h) and long (24 h) filter runs conducted at a pilot filtration plant equipped with large filter columns that simulated full-scale filters. Partially treated surface water from the Sea of Galilee, characterized by very low turbidity (-1 NTU), was used. In the second series of experiments, speciation of aluminium in situ was investigated using the ferron assay method. Results from the pilot-scale study indicate that most PACls were as or more efficient a coagulant as alum for direct filtration of surface water without requiring acid addition for pH adjustment and subsequent base addition for re-stabilizing the water. Consequently, cost analysis of the chemicals needed for the process showed that treatment with PACl would be significantly less costly than treatment with alum. The aluminium speciation experiments revealed that the performance of the coagulant is more influenced by the species present during the coagulation process than those present in the original reagents.

Applied thermodynamics for engineering technologies. 4th edition

International Nuclear Information System (INIS)

Eastop, T.D.; Mc Conkey, A.

1986-01-01

This book presents a complete introduction to the fundamentals of the theory and application of thermodynamics. Revisions include a new chapter on the sources, uses and management of energy as well as major updating of the chapters on internal combustion engines and psychometry. It features new sections on extended surfaces, two-dimensional and transient conduction using finite difference methods, and the NTU method for heat exchanger design. It also stresses the application of theory to real situations and applies principles to practical engineering problems

Water reuse potential in truck wash using a Rotating Biological Contactor

OpenAIRE

Eduardo Lucas Subtil; José Carlos Mierzwa; Ivanildo Hespanhol; Raphael Rodrigues

2016-01-01

This study evaluated the water reuse potential for truck washing using the effluent treated by a Rotating Biological Contactor (RBC) operated in full scale. In order to evaluate the reuse potential, a mass balance was performed for the reuse system taking into account the concentration of Total Dissolved Solids as the critical contaminant. The treatment system produced an effluent with average concentration of color, turbidity, TDS and BOD5 of 45 ± 14 uC, 15 ± 6.0 NTU, 244 ± 99 mg TDS / L and...

Caractérisation physico-chimique et diversité du peuplement ...

African Journals Online (AJOL)

faits au microscope photonique de marque Nikon Eclipse 0,90 Dry. L'étude a révélé une turbidité, un pH et un taux d'oxygène dissous élevés dans les mares Afi et Lagoè avec des valeurs maximales de 8,25 NTU ; 8,14 et. 9,75 mg/L. A Dindin, une conductivité électrique élevée de 590 µS/cm et un taux d'oxydabilité au ...

A LCC model of renewal energy : the cases of water heating system in Taiwan

Energy Technology Data Exchange (ETDEWEB)

Hsu, K.J. [Leader Univ., Tainan City, Taiwan (China). Dept. of Construction Technology; Huang, J.S. [National Taiwan Univ., Taipei, Taiwan (China). Dept. of Bioenvironmental Systems Engineering

2007-07-01

One of the most important renewable energy strategies being promoted by the Bureau of Energy, Ministry of Economic Affairs in Taiwan is the use of solar energy water heating systems. This paper presented the results of a study that examined whether these systems were a feasible alternative without governmental subsidies. Economic methods of investment analysis, such as net benefit analysis, the saving-to-investment ratio, the adjusted internal rate of return, the life cycle cost (LCC) analysis, and sensitivity analysis can be used to evaluate buildings and building systems. Comparing different kinds of energy consumption alternatives, the LCC method is particularly suitable for determining whether the higher initial cost of the systems is economically justified by reductions in future costs. This study used the LCC method to evaluate renewable energy alternatives in Taiwan using water heating systems in the National Taiwan University (NTU) Smart Home as illustrative examples. Three kinds of water heating systems are used in the NTU Smart Home, including the evacuated tubular collectors, heat pump water heating system and power-saving water heating system. This study assessed LCC using gas geyser heating as the contrast group. Sensitivity analysis was used to verify the major factors, and show how it influences life cycle costing. It was concluded that compared with the gas geyser water heating system, the power-saving water heating system was the inefficient scheme. 7 refs., 1 tab., 2 figs.

Changes in the physical properties of the dynamic layer and its correlation with permeate quality in a self-forming dynamic membrane bioreactor.

Science.gov (United States)

Guan, Dao; Dai, Ji; Watanabe, Yoshimasa; Chen, Guanghao

2018-09-01

The self-forming dynamic membrane bioreactor (SFDMBR) is a biological wastewater treatment technology based on the conventional membrane bioreactor (MBR) with membrane material modification to a large pore size (30-100 μm). This modification requires a dynamic layer formed by activated sludge to provide effective filtration function for high-quality permeate production. The properties of the dynamic layer are therefore important for permeate quality in SFDMBRs. The interaction between the structure of the dynamic layer and the performance of SFDMBRs is little known but understandably complex. To elucidate the interaction, a lab-scale SFDMBR system coupled with a nylon woven mesh as the supporting material was operated. After development of a mature dynamic layer, excellent solid-liquid separation was achieved, as evidenced by a low permeate turbidity of less than 2 NTU. The permeate turbidity stayed below this level for nearly 80 days. In the fouling phase, the dynamic layer was compressed with an increase in the trans-membrane pressure and the quality of the permeate kept deteriorating until the turbidity exceeded 10 NTU. The investigation revealed that the majority of permeate particles were dissociated from the dynamic layer on the back surface of the supporting material, which is caused by the compression, breakdown, and dissociation of the dynamic layer. This phenomenon was observed directly in experiment instead of model prediction or conjecture for the first time. Copyright © 2018 Elsevier Ltd. All rights reserved.

Instrument for all-fiber structure measurement of ultra-low turbidity by using single photon detection technique

Science.gov (United States)

Qin, Feihu; Hu, Juntao; Wang, Huanqin; Gui, Huaqiao; Liu, Jianguo; Lü, Liang; Kong, Deyi; Zhang, Jian; Han, Xia; Wang, Tianli

2017-10-01

An all-fiber structure detection system based on single photon detection technique(SPDT) has been developed to measure the ultra-low turbidity ofliquids. To assure the measurement accuracy,the total intensity of transmission light has been detected and quantified as number of photons by avalanche photodiode (APD) which has the advantage of high sensitivity.A fresh all-fiber structure optical fiber probe based on SPDT is applied in the system to reduce the volume and fluctuation of traditional transmission-light measurement system,in which the all-fiber structure probe is used to delivery and collection of transmission light.On the basis of Beer-Lambert (B-L) transmission law,a test system has been established and carried out a series of experiments.By combining B-Llaw with the principle of SPDT,a novel model for detecting turbidity has been proposed to explain the experimental results.The results have shown a well exponential relationship over the range of 0.01-1NTU (Nephelometric Turbidity Units).It also has showna good linear relationship with a resolution as high as 0.01NTUin the range of 0.01-0.09 NTU.When it is 1 secondofthe sampling time,the mean error of measurement result can be controlled within 5% of full scale.In addition,the new detection structure proposed in this paper, which makes the system more compact and more suitable in the small special space.

The effect of turbidity and prey fish density on consumption rates of piscivorous Eurasian perch Perca fluviatilis

DEFF Research Database (Denmark)

Jacobsen, Lene; Berg, Søren; Baktoft, Henrik

2014-01-01

piscivorous Eurasian perch Perca fluviatilis L. This was done in outdoor mesocosm (16 m2) experiments with clear water and two levels of turbidity (25 and 105 NTU) and two prey fish densities [3.1 and 12.5 roach Rutilus rutilus (L.) individuals m–2]. Perch consumption rates were affected by visibility less...... than expected, while they were highly affected by increased prey fish density. Perch responded to high prey density in all visibility conditions, indicating that prey density is more crucial for consumption than visibility in turbid lakes...

Performance of electrodialysis reversal and reverse osmosis for reclaiming wastewater from high-tech industrial parks in Taiwan: A pilot-scale study.

Science.gov (United States)

Yen, Feng-Chi; You, Sheng-Jie; Chang, Tien-Chin

2017-02-01

Wastewater reclamation is considered an absolute necessity in Taiwan, as numerous industrial parks experience water shortage. However, the water quality of secondary treated effluents from sewage treatment plants generally does not meet the requirements of industrial water use because of the high inorganic constituents. This paper reports experimental data from a pilot-plant study of two treatment processes-(i) fiber filtration (FF)-ultrafiltration (UF)-reverse osmosis (RO) and (ii) sand filtration (SF)-electrodialysis reversal (EDR)-for treating industrial high conductivity effluents from the Xianxi wastewater treatment plant in Taiwan. The results demonstrated that FF-UF was excellent for turbidity removal and it was a suitable pretreatment process for RO. The influence of two membrane materials on the operating characteristics and process stability of the UF process was determined. The treatment performance of FF-UF-RO was higher than that of SF-EDR with an average desalination rate of 97%, a permeate conductivity of 272.7 ± 32.0, turbidity of 0.183 ± 0.02 NTU and a chemical oxigen demand of <4.5 mg/L. The cost analysis for both processes in a water reclamation plant of 4000 m 3 /d capacity revealed that using FF-UF-RO had a lower treatment cost than using SF-EDR, which required activated carbon filtration as a post treatment process. On the basis of the results in this study, the FF-UF-RO system is recommended as a potential process for additional applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

Studies of polypropylene membrane fouling during microfiltration of broth with Citrobacter freundii bacteria

Directory of Open Access Journals (Sweden)

Gryta Marek

2015-12-01

Full Text Available In this work a fouling study of polypropylene membranes used for microfiltration of glycerol solutions fermented by Citrobacter freundii bacteria was presented. The permeate free of C. freundii bacteria and having a turbidity in the range of 0.72–1.46 NTU was obtained. However, the initial permeate flux (100–110 L/m2h at 30 kPa of transmembrane pressure was decreased 3–5 fold during 2–3 h of process duration. The performed scanning electron microscope observations confirmed that the filtered bacteria and suspensions present in the broth formed a cake layer on the membrane surface. A method of periodical module rinsing was used for restriction of the fouling influence on a flux decline. Rinsing with water removed most of the bacteria from the membrane surface, but did not permit to restore the initial permeate flux. It was confirmed that the irreversible fouling was dominated during broth filtration. The formed deposit was removed using a 1 wt% solution of sodium hydroxide as a rinsing solution.

Two Examples of Exergy Optimization Regarding the “Thermo-Frigopump” and Combined Heat and Power Systems

Directory of Open Access Journals (Sweden)

Michel Feidt

2013-02-01

Full Text Available In a recent review an optimal thermodynamics and associated new upper bounds have been proposed, but it was only relative to power delivered by engines. In fact, it appears that for systems and processes with more than one utility (mainly mechanical or electrical power, energy conservation (First Law is limited for representing their efficiency. Consequently, exergy analysis combining the First and Second Law seems essential for optimization of systems or processes situated in their environment. For thermomechanical systems recent papers report on comparisons between energy and exergy analysis and corresponding optimization, but the proposed models mainly use heat transfer conductance modelling, except for internal combustion engine. Here we propose to reconsider direct and inverse configurations of Carnot machines, with two examples. The first example is concerned with “thermofrigo-pump” where the two utilities are hot and cold thermal exergies due to the difference in the temperature level compared to the ambient one. The second one is relative to a “combined heat and power” (CHP system. In the two cases, the model is developed based on the Carnot approach, and use of the efficiency-NTU method to characterize the heat exchangers. Obtained results are original thermodynamics optima, that represent exergy upper bounds for these two cases. Extension of the proposed method to other systems and processes is examined, with added technical constraints or not.

[Evaluation of drinking-water treatment by Lifestraw® and Ceramic-pot filters].

Science.gov (United States)

Pérez-Vidal, Andrea; Díaz-Gómez, Jaime; Salamanca-Rojas, Karen L; Rojas-Torres, Leidy Y

2016-04-01

Objective To evaluate under laboratory conditions, the removal efficiency of turbidity and E. coli of two household water filters: LifeStraw® family (MF) and ceramic pot filter (CPF). Methods The two systems were operated over 6 months using two identical control units per system, treating 7.5 L/d of a synthetic substrate used as raw water. The turbidity of the substrate was adjusted with Kaolinite and the E. coli concentration, with a replica of the ATCC 95922 strain. The differences of effluent quality of the systems, in terms of turbidity and E. coli, were evaluated with Analysis of Variance (ANOVA). Operative and maintenance aspects, that could limit or enhance the use of the systems, were also considered in the evaluation. Results The water synthetic substrate quality had an average of 32.2 ± 2.8 NTU for turbidity and 3,9x105 UFC/100 mL for E. coli. Both systems reduce the turbidity to values below 2 NTU with an inactivation of 100 % of E. coli. Statistical differences were found between the systems in terms of turbidity removal, MF being more efficient than the CPF (99,2 ± 0.4 % and 97.6 % ± 1.14, respectively). Conclusions Both systems are suitable for household water supply treatment, acheiving the water quality standards established by Colombian regulations. The MF was more efficient for suspended solids removal and filtration rate, but when economic, operative, and maintenance aspects along with social acceptability and lifespan are considered, the CPF seems more suitable, especially in rural areas.

Applying the coagulation and reverse osmosis for water recovery from evaporative water

Directory of Open Access Journals (Sweden)

Michel Magdalena M.

2014-12-01

Full Text Available Zastosowanie koagulacji i odwróconej osmozy do odzysku wody z wód wyparnych. Wody wyparne z zatężania gęstwy drożdżowej stanowią potencjalny surowiec do odzysku wody. Charakteryzują się niskim odczynem (pH 4.6-6.3, podwyższoną mętnością (3.65-13.7 NTU i dużą zawartością ogólnego węgla organicznego (356-754 mg/L. Badano ich oczyszczanie w procesie koagulacji objętościowej, stosując NaOH oraz koagulant PIX 111. Obniżono mętność wody do wartości poniżej 1 NTU, jednak koagulacja nie pozwalała na usunięcie związków organicznych. Koagulacja przebiegała efektywnie w 20 i 40°C. Oczyszczanie wstępne nadawy do RO obejmowało alkalizację, koagulację, sedymentację i filtrację dokładną (wariant I oraz filtrację dokładną (wariant II jako blank. W wariancie I otrzymano nadawę o lepszych właściwościach. Filtracja membranowa pozwoliła na skuteczne odsolenie wód wyparnych, uzyskano 98 i 73% retencję przewodności w zależności od sposobu przygotowania nadawy. Związki organiczne były usuwane z mniejszą efektywnością, odpowiednio 94 i 84%.

Optimal design of a NGNP heat exchanger with cost model

International Nuclear Information System (INIS)

Ridluan, Artit; Danchus, William; Tokuhiro, Akira

2009-01-01

With steady increase in energy consumption, the vulnerability of the fossil fuel supply, and environmental concerns, the U.S. Department of Energy (DOE) has initiated the Next Generation Nuclear Power Plants (NGNP), also known as Very High Temperature Reactor (VHTR). The VHTR is planned to be operational by 2021 with possible demonstration of a hydrogen generating plant. Various engineering design studies on both the reactor plant and energy conversion system are underway. For this and related Generation IV plants, it is the goal to not only meet safety criteria but to also be efficient, economically competitive, and environmentally friendly (proliferation resistant). Traditionally, heat exchanger (HX) design is based on two main approaches: Log-Mean Temperature Difference (LMTD) and effectiveness-NTU (ε-NTU). These methods yield the dimension of the HX under anticipate condition and vice-versa. However, one is not assured that the dimension calculated give the best performing HX when economics are also considered. Here, we develop and show a specific optimization algorithm (exercise) using LMTD and simple (optimal) design theory to establish a reference case for the Printed Circuit Heat Exchanger (PCHE). Computational Fluid Dynamics (CFD) was further used as a design tool to investigate the optimal design of PCHE thermohydraulic flow. The CFD results were validated against the Blasius correlation before being subjected to optimal design analyses. Benchmark results for the pipe flow indicated that the predictive ability of SST k-ω is superior to the other (standard and RNG k-ε and RSM) turbulence models. The difference between CFD and the empirical expression is less than 10%. (author)

Turbid releases from Glen Canyon Dam, Arizona, following rainfall-runoff events of September 2013

Science.gov (United States)

Wildman, Richard A.; Vernieu, William

2017-01-01

Glen Canyon Dam is a large dam on the Colorado River in Arizona. In September 2013, it released turbid water following intense thunderstorms in the surrounding area. Turbidity was >15 nephelometric turbidity units (NTU) for multiple days and >30 NTU at its peak. These unprecedented turbid releases impaired downstream fishing activity and motivated a rapid-response field excursion. At 5 locations upstream from the dam, temperature, specific conductance, dissolved oxygen, chlorophyll a, and turbidity were measured in vertical profiles. Local streamflow and rainfall records were retrieved, and turbidity and specific conductance data in dam releases were evaluated. Profiling was conducted to determine possible sources of turbidity from 3 tributaries nearest the dam, Navajo, Antelope, and Wahweap creeks, which entered Lake Powell as interflows during this study. We discuss 4 key conditions that must have been met for tributaries to influence turbidity of dam releases: tributary flows must have reached the dam, tributary flows must have been laden with sediment, inflow currents must have been near the depth of dam withdrawals, and the settling velocity of particles must have been slow. We isolate 2 key uncertainties that reservoir managers should resolve in future similar studies: the reach of tributary water into the reservoir thalweg and the distribution of particle size of suspended sediment. These uncertainties leave the source of the turbidity ambiguous, although an important role for Wahweap Creek is possible. The unique combination of limnological factors we describe implies that turbid releases at Glen Canyon Dam will continue to be rare.

Metal oxide/hydroxide-coated dual-media filter for simultaneous removal of bacteria and heavy metals from natural waters.

Science.gov (United States)

Ahammed, M Mansoor; Meera, V

2010-09-15

The present study was conducted to compare the performance of a dual-media filter consisting of manganese oxide-coated (MOCS) and iron hydroxide-coated sand (IOCS) with that of IOCS filter and uncoated sand filter in treating water contaminated by microorganisms, heavy metals and turbidity with a view to its use in simple household water purification devices in developing countries. Long-duration column tests were conducted using two natural waters namely, roof-harvested rainwater and canal water. Performance of the filters showed that dual-media filter was more efficient in removing bacteria and heavy metals compared to IOCS filter, while uncoated sand filter showed very poor performance. The average effluent levels for dual-media filter when tested with rainwater were: turbidity 1.0+/-0.1 NTU; total coliforms 3+/-2 MPN/100 mL; heterotrophic plate count 170+/-20 CFU/mL; zinc 0.06+/-0.01 mg/L, while that for IOCS filter were: turbidity 1.0+/-0.1 NTU; total coliforms 4+/-2 MPN/100 mL; heterotrophic plate count 181+/-37 CFU/mL; zinc 0.20+/-0.07 mg/L. Similar results were obtained for canal water also. Up to 900 bed volumes (BV) could be treated without affecting the efficiency in the case of rainwater, while the filter operation had to be terminated after 500 BV due to excessive headloss in the case of canal water. The study thus showed the potential of the dual-media for use in low-cost household water filters for purification of natural waters. Copyright 2010 Elsevier B.V. All rights reserved.

Ricotta Cheese Whey-Fruit-Based Beverages: Pasteurization Effects on Antioxidant Composition and Color

Directory of Open Access Journals (Sweden)

Anna Rizzolo

2017-02-01

Full Text Available In order to minimize the precipitate formation upon pasteurization for whey-fruit juice-based beverages, a novel type of functional beverage was prepared, in which whey was replaced with Ricotta-cheese whey (RCW. Aiming at evaluating the influence of fruit juice type (yellow: apple, pear; red: blueberry, strawberry and pasteurization conditions on color and antioxidants, four fruit-RCW-based beverages (juice/RCW ratio: 80/20, 14% soluble solids content were prepared and divided into two lots, and each lot was pasteurized according to different times/temperatures. After pasteurization, no formation of precipitate was observed in the bottles, even if some turbidity, ranging from 25 NTU (pear-RCW to 190 NTU (blueberry-RCW, was observed. The blending of juices with RCW caused color darkening in apple, pear, and strawberry blends, and brightening in the blueberry one. The pasteurization conditions had a greater impact on the color changes of ‘yellow’ beverages than those of the ‘red’ ones. With a lethal rate F 100 10 = 14 , there was a greater decrease in the total phenolic content (TPC in blueberry-, strawberry-, and apple-RCW beverages, and a greater decrease in the monomeric anthocyanin pigment (MAP and a smaller increase in the percent of polymeric color, in the blueberry-RCW beverage. Results on the antioxidant activity suggested that the Maillard reaction products formed in response to thermal treatment and/or the formation of anthocyanin polymers, likely compensate for the loss of antioxidant activity due to TPC and MAP degradations.

Molecular detection, quantification, and isolation of Streptococcus gallolyticus bacteria colonizing colorectal tumors: inflammation-driven potential of carcinogenesis via IL-1, COX-2, and IL-8

Directory of Open Access Journals (Sweden)

Abdulamir Ahmed S

2010-09-01

Full Text Available Abstract Background Colorectal cancer (CRC has long been associated with bacteremia and/or endocarditis by Streptococcus gallolyticus member bacteria (SGMB but the direct colonization of SGMB along with its molecular carcinogenic role, if any, has not been investigated. We assessed the colonization of SGMB in CRC patients with history of bacteremia (CRC-w/bac and without history of bacteremia (CRC-wo/bac by isolating SGMB from feces, mucosal surfaces of colorectum, and colorectal tissues and detecting SGMB DNA, via PCR and in situ hybridization (ISH assays targeting SodA gene in colorectal tissues. Moreover, mRNA of IL1, IL-8, COX-2, IFN-γ, c-Myc, and Bcl-2 in colorectal tissues of studied groups was assessed via ISH and RT-PCR. Results SGMB were found to be remarkably isolated in tumorous (TU and non-tumorous (NTU tissues of CRC-w/bac, 20.5% and 17.3%, and CRC-wo/bac, 12.8% and 11.5%, respectively while only 2% of control tissues revealed SGMB (P 10 CN/g respectively, showed higher colonization in TU than in NTU and in CRC-w/bac than in CRC-wo/bac (P Conclusions The current study indicated that colorectal cancer is remarkably associated with SGMB; moreover, molecular detection of SGMB in CRC was superior to link SGMB with CRC tumors highlighting a possible direct and active role of SGMB in CRC development through most probably inflammation-based sequel of tumor development or propagation via, but not limited to, IL-1, COX-2, and IL-8.

Risk assessment of Giardia from a full scale MBR sewage treatment plant caused by membrane integrity failure.

Science.gov (United States)

Zhang, Yu; Chen, Zhimin; An, Wei; Xiao, Shumin; Yuan, Hongying; Zhang, Dongqing; Yang, Min

2015-04-01

Membrane bioreactors (MBR) are highly efficient at intercepting particles and microbes and have become an important technology for wastewater reclamation. However, many pathogens can accumulate in activated sludge due to the long residence time usually adopted in MBR, and thus may pose health risks when membrane integrity problems occur. This study presents data from a survey on the occurrence of water-borne Giardia pathogens in reclaimed water from a full-scale wastewater treatment plant with MBR experiencing membrane integrity failure, and assessed the associated risk for green space irrigation. Due to membrane integrity failure, the MBR effluent turbidity varied between 0.23 and 1.90 NTU over a period of eight months. Though this turbidity level still met reclaimed water quality standards (≤5 NTU), Giardia were detected at concentrations of 0.3 to 95 cysts/10 L, with a close correlation between effluent turbidity and Giardia concentration. All β-giardin gene sequences of Giardia in the WWTP influents were genotyped as Assemblages A and B, both of which are known to infect humans. An exponential dose-response model was applied to assess the risk of infection by Giardia. The risk in the MBR effluent with chlorination was 9.83×10(-3), higher than the acceptable annual risk of 1.0×10(-4). This study suggested that membrane integrity is very important for keeping a low pathogen level, and multiple barriers are needed to ensure the biological safety of MBR effluent. Copyright © 2015. Published by Elsevier B.V.

Supervision of the thermal performance of heat exchanger trains

Energy Technology Data Exchange (ETDEWEB)

Negrao, C.O.R.; Tonin, P.C.; Madi, M. [Federal University of Technology Parana UTFPR, Post-graduate Program in Mechanical and Materials Engineering PPGEM, Thermal Science Laboratory LACIT, Av. Sete de Setembro, 3165, CEP 80230-901, Curitiba, Parana (Brazil)

2007-02-15

In oil refining, heat exchanger networks are employed to recover heat and therefore save energy of the plant. However, many heat exchangers in crude oil pre-heat trains are under high risk of fouling. Under fouling conditions, the thermal performance of heat exchangers is continuously reduced and its supervision becomes an important task. The large number of heat exchangers in pre-heat trains and the change of operation conditions and feedstock charges make the daily supervision a difficult task. This work applies an approach to follow the performance of heat exchangers [M.A.S. Jeronimo, L.F. Melo, A.S. Braga, P.J.B.F. Ferreira, C. Martins, Monitoring the thermal efficiency of fouled heat exchangers - A simplified method, Experimental Thermal and Fluid Science 14 (1997) 455-463] and extends it to monitor the whole train. The approach is based on the comparison of measured and predicted heat exchanger effectiveness. The measured value is computed from the four inlet and outlet temperatures of a heat exchanger unit. The predicted clean and dirty values of effectiveness are calculated from classical literature relations as a function of NTU and of heat capacity ratio (R). NTU and R are continuously adjusted according to mass flow rate changes. An index of fouling is defined for the whole network and the results show the performance degradation of the network with time. The work also suggests that Jeronimo's index of fouling can be used to estimate the fouling thermal resistance of heat exchangers. (author)

Disinfection of municipal water using solar radiation: an economical approach for rural dwellers in the coastal region of Karachi

International Nuclear Information System (INIS)

Ahmed, M.F.; Saleem, M.

2010-01-01

At present acquiring safe drinking water in rural or remote areas of Pakistan is a challenging task for dwellers. Coast line of Karachi is a sporadic habitat of villages not having access to safe drinking water. Many incidents of waterborne diseases have been reported in that area and attributed to contaminated municipal water supply. Solution of the problem is disinfection however, general methods of water disinfection such as boiling, UV-lamp, ozonation and chemical additive are costly or require skilled manpower. Present study investigates the solar disinfection method to treat municipal water supply at Karachi Institute of Power Engineering (KINPOE) located at the coastal belt of Karachi. Effect of exposure time, bottle material and turbidity of water on the process performance was evaluated. Model indicator bacteria total coliform (TC) was used to evaluate the solar disinfection process. Study revealed that in order to disinfect the municipal water, samples should be filled in PET transparent bottles, having turbidity below 23 NTU, and expose to solar radiation in the study area at least for one hour. Study shows that solar disinfection may provide safe drinking water meeting national and international water quality standards at minimum cost and effort in sunshine rich areas and not having access to other water purification systems. (author)

Coagulation effectiveness of graphene oxide for the removal of turbidity from raw surface water.

Science.gov (United States)

Aboubaraka, Abdelmeguid E; Aboelfetoh, Eman F; Ebeid, El-Zeiny M

2017-08-01

This study presents the performance of graphene oxide (GO) as a coagulant in turbidity removal from naturally and artificially turbid raw surface water. GO is considered an excellent alternative to alum, the more common coagulant used in water treatment processes, to reduce the environmental release of aluminum. Effects of GO dosage, pH, and temperature on its coagulation ability were studied to determine the ideal turbidity removal conditions. The turbidity removal was ≥95% for all levels of turbid raw surface water (20, 100, and 200 NTU) at optimum conditions. The role of alkalinity in inducing turbidity removal by GO coagulation was much more pronounced upon using raw surface water samples compared with that using artificially turbid deionized water samples. Moreover, GO demonstrated high-performance removal of biological contaminants such as algae, heterotrophic bacteria, and fecal coliform bacteria by 99.0%, 98.8% and 96.0%, respectively, at a dosage of 40 mg/L. Concerning the possible environmental release of GO into the treated water following filtration process, there was no residual GO in a wide range of pH values. The outcomes of the study highlight the excellent coagulation performance of GO for the removal of turbidity and biological contaminants from raw surface water. Copyright © 2017 Elsevier Ltd. All rights reserved.

Dynamic Membrane Technology for Printing Wastewater Reuse

Science.gov (United States)

Liu, Lin; Lu, Xujie; Chen, Jihua

As environmental regulations become rigid and the cost of freshwater increases, wastewater is considered as a major resource in China. The paper presented a study on the implementation of the advanced treatment process using dynamic membrane (DM) in reusing of printing wastewater. The DM was well formed by circulating 1.5g/L of PAC in 20 minutes, the trans-membrane pressure of 200 kPa and the cross-flow velocity of 0.75m/s. The printing effluents were treated in effluent treatment plants comprising a physicochemical option followed by biological process. The treated effluent contained chemical oxygen demand (COD), color and turbidity in the range of 45-60 mg/L, 0.030-0.045 (absorbance at 420 nm) and 3-5 NTU. The results showed that the COD, color and turbidity removal efficiencies of the DM permeate were 84%, 85% and 80%, respectively. The wastewater treated by DM was reused as process water and the final concentrated retentate could be discharged directly into sewage treatment works with no additional treatments. Cleaning and regeneration of DM were very convenient if necessary. The proper process was that the polluted DM was cleaned with tap water at high cross-flow velocity. When irreversible pollutants accumulate, it would be rinsed with chemicals tested and the membrane flux would be restored up to 95%. The result showed that DM was considered as a promising method for purification aimed at reuse of printing wastewater, resulting in direct environmental and economic benefits.

EXPERIMENTAL STUDY ON HEAT TRANSFER COEFFICIENT AND FRICTION FACTOR OF Al2O3 NANOFLUID IN A PACKED BED COLUMN

Directory of Open Access Journals (Sweden)

G. Srinivasa Rao

2011-12-01

Full Text Available The forced convection heat transfer coefficient and friction factor are determined for the flow of water and nanofluid in a vertical packed bed column. The analysis is undertaken in the laminar and transition Reynolds number range. The column is filled with spherical glass beads as the bed material. The heat transfer coefficients with Al2O3 nanofluid increased by 12% to 15% with the increase of volume concentration from 0.02% to 0.5% compared with water. The experimental values of axial temperature are in good agreement with the NTU-ε method proposed by Schumann’s model.

Engineering faculty forum. Final report, June 1, 1993--May 31, 1994

Energy Technology Data Exchange (ETDEWEB)

Baldwin, L.V.

1994-11-01

The goal of the project was to develop and broadcast monthly one-hour teleconferences to support the professional development of engineering faculty. The {open_quotes}Engineering Faculty Forum{close_quotes} was available nationwide over the NTU Satellite Network and was also available from a C-Band Satellite. There was no cost to participate in the live teleconferences for the two year period. The programs were developed in response to a questionnaire sent to engineering faculty members across the United States. Copies of the flyers and a print out of each course participation form has been included as a part of this report.

The International Symposium on Microwave Signatures and Remote Sensing Held in Gothenburg (Sweden) on 19-22 January 1987.

Science.gov (United States)

1987-05-28

7 A-A1 I 334 NT NAI A SNI JN O ICR MUfI CM NTU AN III UNCLASSIF ED Rkl~ lWLA 2MY90 LAF/C 17/9 ML u-iD i1.0 V , .2 2 il4 016 - 9 I or 9P: FILE OM...returned radar signal to sea various mathematical models. The group state it has been found that the scatter- studied these spikes in an attempt to...Sobieski (Univer- object. A mathematical model relating sity of Louvain, Belgium) attempted to these parameters was developed but no develop an

A Hartree-Fock program for atomic structure calculations

International Nuclear Information System (INIS)

Mitroy, J.

1999-01-01

The Hartree-Fock equations for a general open shell atom are described. The matrix equations that result when the single particle orbitals are written in terms of a linear combination of analytic basis functions are derived. Attention is paid to the complexities that occur when open shells are present. The specifics of a working FORTRAN program which is available for public use are described. The program has the flexibility to handle either Slater-type orbitals or Gaussian-type orbitals. It can be obtained over the internet at http://lacebark.ntu.edu.au/j_mitroy/research/atomic.htm Copyright (1999) CSIRO Australia

Geochemistry, processes and environmental impact caused by the mining and auriferous ore process in the Marmato District (Caldas Department, Colombia)

International Nuclear Information System (INIS)

Prieto Rincon, Gloria

1995-01-01

Area. Have values for solid load (TS 208 - 234 mg/L) and turbidity (40.80 - 62.7 NTU) in agreement in to values for other natural rivers that carry loads of erosive materials. Its pH is into the neutral range, for natural water rivers (7.18 - 7.35). Dilutions processes must be operate in the Cauca River because of its discharge (605.3 -641.8 m 3 /s). Because of its fast rate flow (falling from higher to lower level) and pH values it is possible that geochemical reactions in that region of the Cauca river could be fewer than in other tropical river systems and some of the normal interactions must be operate harder downstream from Marmato Area. So, for the second sampling field programmed, emphasis will be stressed onto the Cauca River system, downstream from Marmato, taking the environmental compartments, water, sediments (core samples), and suspended particulate matter, as geochemical sampling media. In order to understand the geochemical behavior of the studied heavy metals, selective extractions methods for geochemical speciation, and isotope dating ( 210 Pb) for accumulation rate, will be carrying out. This thesis work is carried out with financial support and cooperation of the German Academic Exchange Service (DAAD) and INGEOMINAS from Colombia and technical assistance and cooperation of the Universidade Federal do Para (UFP A), and Universidade federal Fluminense (UFF), from Brazil

Avaliação da eficiência da estação de tratamento de águas residuárias de uma lavanderia de jeans

Directory of Open Access Journals (Sweden)

Jéssica Talita Zagonel

2015-12-01

Full Text Available No presente trabalho avaliou-se o tratamento das águas residuárias adotado numa lavanderia industrial, situada no Meio Oeste Catarinense. Os objetivos deste, consistiram em analisar a eficiência da estação, comparando os resultados finais como os padrões de emissões permitidos pela CONAMA 430/2011 e a LEI Nº 14.675/2009 (SC. Para isto foram empregados métodos de: caracterização das águas residuárias bruta e tratada; caracterização e determinação da vazão do corpo hídrico receptor. Sendo assim, a vazão média do corpo hídrico 0,033 m³.s-1. Este exibiu teores médios de OD 8,28 mg.L-1, DBO 123,01 mg.L-1, DQO (não expressiva, SST 18,56 mg.L-1, turbidez 0,939 NTU, fósforo 9,27 mg.L-1, surfactantes 0,83 mg.L-1 e pH 6,64. Nas águas residuárias bruta, os teores médios aferidos foram: DBO 206,90 mg.L-1; DQO 689,65 mg.L-1; SST 1,50 mg.L-1; SS 488,40 mL.L-1; fósforo 367,32 mg.L-1; surfactantes 2,12 mg.L-1; pH 6,56; OD 2,18 mg.L-1 e turbidez 6,15 NTU; Já para as águas residuárias tratadas: DBO 116,1 mg.L-1; DQO 121,37 mg.L-1; SST 0,00 mg.L-1; SS 5,00 e 21,50 mL.L-1 (dias 22 e 29/09; fósforo 23,60 mg.L-1; surfactantes 0,387 mg.L-1; pH 5,70; OD 6,04 mg.L-1 e turbidez 0,352 NTU. Com relação a eficiência da estação de tratamento, esta apresentou remoção de DBO < 40%, presença de SST, em algumas amostras, e ausência de SS. O pH, em algumas análises, ficou abaixo de 6,00. A remoção média de fósforo e surfactantes foi de 80% e 83,13% respectivamente. Diante destes resultados e segundo o que preconiza as legislações citadas, a estação avaliada possui eficiência de 57%.

Assessment of the impacts of pit latrines on groundwater quality in rural areas: A case study from Marondera district, Zimbabwe

Science.gov (United States)

Dzwairo, Bloodless; Hoko, Zvikomborero; Love, David; Guzha, Edward

In resource-poor and low-population-density areas, on-site sanitation is preferred to off-site sanitation and groundwater is the main source of water for domestic uses. Groundwater pollution potential from on-site sanitation in such areas conflicts with Integrated Water Resources Management (IWRM) principles that advocate for sustainable use of water resources. Given the widespread use of groundwater for domestic purposes in rural areas, maintaining groundwater quality is a critical livelihood intervention. This study assessed impacts of pit latrines on groundwater quality in Kamangira village, Marondera district, Zimbabwe. Groundwater samples from 14 monitoring boreholes and 3 shallow wells were analysed during 6 sampling campaigns, from February 2005 to May 2005. Parameters analysed were total and faecal coliforms, NH4+-N, NO3--N, conductivity, turbidity and pH, both for boreholes and shallow wells. Total and faecal coliforms both ranged 0-TNTC (too-numerous-to-count), 78% of results meeting the 0 CFU/100 ml WHO guidelines value. NH4+-N range was 0-2.0 mg/l, with 99% of results falling below the 1.5 mg/l WHO recommended value. NO3--N range was 0.0-6.7 mg/l, within 10 mg/l WHO guidelines value. The range for conductivity values was 46-370 μS/cm while the pH range was 6.8-7.9. There are no WHO guideline values for these two parameters. Turbidity ranged from 1 NTU to 45 NTU, 59% of results meeting the 5 NTU WHO guidelines limit. Depth from the ground surface to the water table for the period February 2005 to May 2005 was determined for all sampling points using a tape measure. The drop in water table averaged from 1.1 m to 1.9 m and these values were obtained by subtracting water table elevations from absolute ground surface elevation. Soil from the monitoring boreholes was classified as sandy. The soil infiltration layer was taken as the layer between the pit latrine bottom and the water table. It averaged from 1.3 m to 1.7 m above the water table for two latrines

Water quality requirements for sustaining aquifer storage and recovery operations in a low permeability fractured rock aquifer.

Science.gov (United States)

Page, Declan; Miotliński, Konrad; Dillon, Peter; Taylor, Russel; Wakelin, Steve; Levett, Kerry; Barry, Karen; Pavelic, Paul

2011-10-01

A changing climate and increasing urbanisation has driven interest in the use of aquifer storage and recovery (ASR) schemes as an environmental management tool to supplement conventional water resources. This study focuses on ASR with stormwater in a low permeability fractured rock aquifer and the selection of water treatment methods to prevent well clogging. In this study two different injection and recovery phases were trialed. In the first phase ~1380 m(3) of potable water was injected and recovered over four cycles. In the second phase ~3300 m(3) of treated stormwater was injected and ~2410 m(3) were subsequently recovered over three cycles. Due to the success of the potable water injection cycles, its water quality was used to set pre-treatment targets for harvested urban stormwater of ≤ 0.6 NTU turbidity, ≤ 1.7 mg/L dissolved organic carbon and ≤ 0.2 mg/L biodegradable dissolved organic carbon. A range of potential ASR pre-treatment options were subsequently evaluated resulting in the adoption of an ultrafiltration/granular activated carbon system to remove suspended solids and nutrients which cause physical and biological clogging. ASR cycle testing with potable water and treated stormwater demonstrated that urban stormwater containing variable turbidity (mean 5.5 NTU) and organic carbon (mean 8.3 mg/L) concentrations before treatment could be injected into a low transmissivity fractured rock aquifer and recovered for irrigation supplies. A small decline in permeability of the formation in the vicinity of the injection well was apparent even with high quality water that met turbidity and DOC but could not consistently achieve the BDOC criteria. Copyright © 2011 Elsevier Ltd. All rights reserved.

Physico-chemical and bacteriological quality of water from shallow wells in two rural communities in Benue state, Nigeria

International Nuclear Information System (INIS)

Terngu, A.J.; Hyacinth, O.A.; Rufus, S.A.

2010-01-01

Ground water abstraction from shallow wells is widely practiced in the Obi and in Oju rural areas of Benue State, Central Nigeria, as a means of fighting guinea worm infestation associated with the surface water sources (streams) in these areas. To ascertain the physico-chemical and bacteriological quality of the water used by the population, water samples from 27 shallow wells in Obi and 19 Oju were taken and examined for key health -related quality parameters using routine methods. In Obi, the ground water colour ranged from 4.0-80.0 TCU, conductivity 55.2- 1600.0 ILS/cm, pH 6.1-8.6, TDS 38.6-1286 mg/L, turbidity 1.0 - 55.0 NTU, arsenic 0.001- 0.210 mg/L, copper 0.01-2.53 mg/L, fluoride 0.08-1.82 mg/L and nitrate 10.8-63.0 mg/L; while in Oju, colour varied from 2.0-87.0 TCU, conductivity 1 07.4-1375 LS/cmp, H 6.4-8.53, TDS 75.2- 1150 mg/L, turbidity 3.0-48.0 NTU, arsenic 0.001-0.023 mg/L, copper 0.01-2.10 mg/L, fluoride 0.01-1.54 mg/L and nitrate 10.2-59.7 mg/L. Some of these values in some instances exceed the WHO standard for drinking water. Alongside with the presence significant total coliform count in most of the wells (0-47/100 mL in Oju and 0-53/100 mL in Obi), the available water is considered largely unsafe for human consumption as obtained. (author)

Modeling the small-scale dish-mounted solar thermal Brayton cycle

Science.gov (United States)

Le Roux, Willem G.; Meyer, Josua P.

2016-05-01

The small-scale dish-mounted solar thermal Brayton cycle (STBC) makes use of a sun-tracking dish reflector, solar receiver, recuperator and micro-turbine to generate power in the range of 1-20 kW. The modeling of such a system, using a turbocharger as micro-turbine, is required so that optimisation and further development of an experimental setup can be done. As a validation, an analytical model of the small-scale STBC in Matlab, where the net power output is determined from an exergy analysis, is compared with Flownex, an integrated systems CFD code. A 4.8 m diameter parabolic dish with open-cavity tubular receiver and plate-type counterflow recuperator is considered, based on previous work. A dish optical error of 10 mrad, a tracking error of 1° and a receiver aperture area of 0.25 m × 0.25 m are considered. Since the recuperator operates at a very high average temperature, the recuperator is modeled using an updated ɛ-NTU method which takes heat loss to the environment into consideration. Compressor and turbine maps from standard off-the-shelf Garrett turbochargers are used. The results show that for the calculation of the steady-state temperatures and pressures, there is good comparison between the Matlab and Flownex results (within 8%) except for the recuperator outlet temperature, which is due to the use of different ɛ-NTU methods. With the use of Matlab and Flownex, it is shown that the small-scale open STBC with an existing off-the-shelf turbocharger could generate a positive net power output with solar-to-mechanical efficiency of up to 12%, with much room for improvement.

Building and Calibration of a FAST Model of the SWAY Prototype Floating Wind Turbine: Preprint

Energy Technology Data Exchange (ETDEWEB)

Koh, J. H.; Robertson, A.; Jonkman, J.; Driscoll, F.; Ng, E. Y. K.

2013-09-01

Present efforts to verify and validate aero-hydro-servo-elastic numerical simulation tools that predict the dynamic response of a floating offshore wind turbine are primarily limited to code-to-code comparisons or code-to-data comparisons using data from wind-wave basin tests. In partnership with SWAY AS, the National Renewable Energy Laboratory (NREL) installed scientific wind, wave, and motion measurement equipment on the 1/6.5th-scale prototype SWAY floating wind system to collect data to validate a FAST model of the SWAY design in an open-water condition. Nanyang Technological University (NTU), through a collaboration with NREL, assisted in this validation.

Comparison of Water Turbidity Removal Efficiencies of Descurainia Sophia Seed Extract and Ferric chloride

Directory of Open Access Journals (Sweden)

Mazyar Peyda

2016-03-01

Full Text Available Background Turbidity removal using inorganic coagulants such as iron and aluminum salts in water treatment processes causes environmental and human health concern. Historically, the use of natural coagulant to purify turbid water has been practiced for a long time. Recent research indicates that Descurainia Sophia seed can be effectively used as a natural coagulant to remove water turbidity. Method: In this work, turbidity removal efficiency of Descurainia Sophia seed extract was compared with Ferric chloride. Experiments were performed in laboratory scale. The coagulation experiments were done with kaolin as a model soil to produce turbidity in distilled water. The turbidity removal efficiency of Descurainia Sophia seed extract and Ferric chloride were conducted with jar test apparatus. In all experiments, initial turbidity was kept constant 100(NTU. Optimum combination of independent variables was used to compare two different types of coagulants. Result: The obtained results showed that Ferric chloride could remove 89.75% of the initial turbidity, while in case of Descurainia Sophia this value was 43.13%. The total organic carbon (TOC analysis of the treated water using seed extract showed an increased concentration of TOC equal to 0.99 mg/L. Conclusions: This research has shown that Descurainia Sophia seed extract has an acceptable potential in the coagulation/flocculation process to treat turbid water.

Reduction of Acid-Fast and Non-Acid-Fast Bacteria by Point of Use Coagulation-Flocculation-Disinfection

Directory of Open Access Journals (Sweden)

Lisa M. Casanova

2015-11-01

Full Text Available Point of use (POU household water treatment is increasingly being adopted as a solution for access to safe water. Non-tuberculous Mycobacteria (NTM are found in water, but there is little research on whether NTM survive POU treatment. Mycobacteria may be removed by multi-barrier treatment systems that combine processes such as coagulation, settling and disinfection. This work evaluated removal of a non-tuberculous Mycobacterium (Mycobaterium terrae and a Gram-negative non-acid-fast environmental bacterium (Aeromonas hydrophila by combined coagulation-flocculation disinfection POU treatment. Aeromonas hydrophila showed 7.7 log10 reduction in demand free buffer, 6.8 log10 in natural surface water, and 4 log10 reduction in fecally contaminated surface water. Turbidity after treatment was <1 NTU. There was almost no reduction in levels of viable M. terrae by coagulant-flocculant-disinfectant in natural water after 30 minutes. The lack of Mycobacteria reduction was similar for both combined coagulant-flocculant-disinfectant and hypochlorite alone. A POU coagulant-flocculant-disinfectant treatment effectively reduced A. hydrophila from natural surface waters but not Mycobacteria. These results reinforce previous findings that POU coagulation-flocculation-disinfection is effective against gram-negative enteric bacteria. POU treatment and safe storage interventions may need to take into account risks from viable NTM in treated stored water and consider alternative treatment processes to achieve NTM reductions.

Monascus-fermented red mold dioscorea protects mice against alcohol-induced liver injury, whereas its metabolites ankaflavin and monascin regulate ethanol-induced peroxisome proliferator-activated receptor-γ and sterol regulatory element-binding transcription factor-1 expression in HepG2 cells.

Science.gov (United States)

Cheng, Chih-Fu; Pan, Tzu-Ming

2018-03-01

Alcoholic hepatitis is a necroinflammatory process that is associated with fibrosis and leads to cirrhosis in 40% of cases. The hepatoprotective effects of red mold dioscorea (RMD) from Monascus purpureus NTU 568 were evaluated in vivo using a mouse model of chronic alcohol-induced liver disease (ALD). ALD mice were orally administered vehicle (ALD group) or vehicle plus 307.5, 615.0 or 1537.5 mg kg -1 (1 ×, 2 × and 5 ×) RMD for 5 weeks. RMD lowered serum leptin, hepatic total cholesterol, free fatty acid and hepatic triglyceride levels and increased serum adiponectin, hepatic alcohol dehydrogenase and antioxidant enzyme levels. Furthermore, ankaflavin (AK) and monascin (MS), metabolites of RMD fermented with M. purpureus 568, induced peroxisome proliferator-activated receptor-γ expression and the concomitant suppression of ethanol-induced elevation of sterol regulatory element-binding transcription factor-1 and TG in HepG2 cells. These results indicate the hepatoprotective effect of Monascus-fermented RMD. Moreover, AK and MS were identified as the active constituents of RMD for the first time and were shown to protect against ethanol-induced liver damage. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Efficiency of Moringa oleifera Seeds for Treatment of Laundry Wastewater

Directory of Open Access Journals (Sweden)

Al-Gheethi AA

2017-01-01

Full Text Available Laundry wastewater has simple characteristics in which the detergents compounds are the main constitutes. But these compounds have adverse effects on the aquatic organisms in the natural water bodies which received these wastes without treatment. Few studies were conducted on these wastes because it represent a small part of the total wastewater generated from different human activities. Moreover, the coagulation process for laundry wastewater might be effective to remove of detergents compounds. Therefore, in the present study, the efficiency of coagulation process by using chemical (ferrous sulphate and natural coagulants (Moringa oleifera seeds were investigated. The raw laundry wastewater samples were collected from laundromat located at Taman Universiti, Parit Raja. The characteristics of these wastes were determined and then the wastewater was subjected for the treatment process consisted of three units including aeration, coagulation and sedimentation process. The chemical and natural coagulants were used with four dosage (30, 60, 90 and 120 mg L−1 and the coagulation process was carried out at room temperature (25±2ºC for one hour. The results revealed that the laundry wastewater have high concentrations of turbidity (57.8-68.1 NTU and Chemical Oxygen Demand (COD (423-450 mg L−1 with pH value between 7.96 and 8.37. M. oleifera seeds exhibited high efficiency for removal of turbidity (83.63% with 120 mg L−1 of dosage, while 30 mg L−1 of FeSO4 was the best for removal of COD (54.18%. However, both parameters still more than Standard B for wastewater disposal suggesting the need to increase the period of coagulation process with M. oleifera seeds or to subject of the treated effluents for a secondary coagulation process with natural coagulant products to improve the characteristics of laundry wastewater without a secondary products as that generated with the chemical coagulants.

Physico-chemical and Bacteriological Quality of Water from Shallow Wells in Two Rural Communities in Benue State, Nigeria

Directory of Open Access Journals (Sweden)

Akaahan, Terngu J.

2010-06-01

Full Text Available Ground water abstraction from shallow wells is widely practiced in the Obi and in Oju rural areas of Benue State, Central Nigeria, as a means of fighting guinea worm infestation associated with the surface water sources (streams in these areas. To ascertain the physico-chemical and bacteriological quality of the water used by the population, water samples from 27 shallow wells in Obi and 19 Oju were taken and examined for key health-related quality parameters using routine methods. In Obi, the ground water colour ranged from 4.0-80.0 TCU, conductivity 55.2-1600.0 µS/cm, pH 6.1-8.6, TDS 38.6-1286 mg/L, turbidity 1.0-55.0 NTU, arsenic 0.001-0.210mg/L, copper 0.01-2.53mg/L, fluoride 0.08-1.82mg/L and nitrate 10.8-63.0mg/L, while in Oju, colour varied from 2.0-87.0 TCU, conductivity 107.4-1375 µS/cm, pH 6.4-8.53, TDS 75.2-1150 mg/L, turbidity 3.0-48.0 NTU, arsenic 0.001-0.023 mg/L, copper 0.01-2.10 mg/L, fluoride 0.01-1.54 mg/L and nitrate 10.2-59.7 mg/L. Some of these values in some instances exceed the WHO standard for drinking water. Alongside with the presence significant total coliform count in most of the wells (0-47/100 mL in Oju and 0-53/100 mL in Obi, the available water is considered largely unsafe for human consumption as obtained. It is concluded that, while ground water abstraction may be a safety measure against guinea worm infestation it, nevertheless presents other health challenges to the rural population in the area, as the quality of the ground water is generally low.

A simplified model to study the location impact of latent thermal energy storage in building cooling heating and power system

International Nuclear Information System (INIS)

Zhang, Yin; Wang, Xin; Zhang, Yinping; Zhuo, Siwen

2016-01-01

Introducing the thermal energy storage (TES) equipment into the building cooling heating and power (BCHP) system proves to be an effective way to improve the part load performance of the whole system and save the primary energy consumption. The location of TES in BCHP has a great impact on the thermal performance of the whole system. In this paper, a simplified model of TES-BCHP system composed of a gas turbine, an absorption chiller/an absorption heat pump, and TES equipment with phase change materials (PCM) is presented. In order to minimize the primary energy consumption, the performances of BCHP systems with different PCM-TES locations (upstream and downstream) are analyzed and compared, for a typical hotel and an office building respectively. Moreover, the influence of the thermal performance of PCM-TES equipment on the energy saving effect of the whole system is investigated. The results confirm that PCM-TES can improve the energy efficiency and reduce the installed capacities of energy supply equipment, and that the optimal TES location in BCHP highly depends on the thermal performance of the TES equipment and the user load characteristics. It also indicates that: 1) the primary energy saving ratio of PCM-TES-BCHP increases with increasing NTU of TES; 2) for the studied cases, downstream TES location becomes more preferable when user loads fluctuate greatly; 3) only downstream TES can reduce the installed capacities of absorption chiller/absorption heat pump. This work can provide guidance for PCM-TES-BCHP system design. - Highlights: • A simplified model of the PCM-TES-BCHP system is established. • TES can increase energy efficiency and decrease installed capacity of equipment. • Primary energy saving ratio increases with increasing NTU of TES. • Downstream TES location is more preferable when user loads fluctuate greatly. • Optimal TES location depends on equipment performances and load characteristics.

Use of Moringa oleifera seed extracts to reduce helminth egg numbers and turbidity in irrigation water.

Science.gov (United States)

Sengupta, Mita E; Keraita, Bernard; Olsen, Annette; Boateng, Osei K; Thamsborg, Stig M; Pálsdóttir, Guðný R; Dalsgaard, Anders

2012-07-01

Water from wastewater-polluted streams and dug-outs is the most commonly used water source for irrigation in urban farming in Ghana, but helminth parasite eggs in the water represent health risks when used for crop production. Conventional water treatment is expensive, requires advanced technology and often breaks down in less developed countries so low cost interventions are needed. Field and laboratory based trials were carried out in order to investigate the effect of the natural coagulant Moringa oleifera (MO) seed extracts in reducing helminh eggs and turbidity in irrigation water, turbid water, wastewater and tap water. In medium to high turbid water MO extracts were effective in reducing the number of helminth eggs by 94-99.5% to 1-2 eggs per litre and the turbidity to 7-11 NTU which is an 85-96% reduction. MO is readily available in many tropical countries and can be used by farmers to treat high turbid water for irrigation, however, additional improvements of water quality, e.g. by sand filtration, is suggested to meet the guideline value of ≤ 1 helminth egg per litre and a turbidity of ≤ 2 NTU as recommended by the World Health Organization and the U.S. Environmental Protection Agency for water intended for irrigation. A positive correlation was established between reduction in turbidity and helminth eggs in irrigation water, turbid water and wastewater treated with MO. This indicates that helminth eggs attach to suspended particles and/or flocs facilitated by MO in the water, and that turbidity and helminth eggs are reduced with the settling flocs. However, more experiments with water samples containing naturally occurring helminth eggs are needed to establish whether turbidity can be used as a proxy for helminth eggs. Copyright © 2012 Elsevier Ltd. All rights reserved.

Potencial de reúso de água na lavagem de caminhões utilizando Contator Biológico Rotativo

OpenAIRE

Subtil, Eduardo Lucas; Mierzwa, José Carlos; Hespanhol, Ivanildo; Rodrigues, Raphael

2016-01-01

Este estudo teve como objetivo avaliar o potencial de reúso de água na lavagem de caminhões a partir do efluente tratado por um Contator Biológico Rotativo operado em escala real. Para avaliação do potencial de reúso foi realizado um balanço de massa para o sistema de reúso levando em consideração a concentração de Sólidos Dissolvidos Totais como contaminante crítico. O sistema de tratamento produziu um efluente com concentrações médias de cor, turbidez, SDT e DBO5 de 45 ± 14 uC, 15 ± 6,0 NTU...

Performance Evaluation of Air-Based Heat Rejection Systems

Directory of Open Access Journals (Sweden)

Hannes Fugmann

2015-01-01

Full Text Available On the basis of the Number of Transfer Units (NTU method a functional relation between electric power for fans/pumps and effectiveness in dry coolers and wet cooling towers is developed. Based on this relation, a graphical presentation method of monitoring and simulation data of heat rejection units is introduced. The functional relation allows evaluating the thermodynamic performance of differently sized heat rejection units and comparing performance among them. The method is used to evaluate monitoring data of dry coolers of different solar cooling field projects. The novelty of this approach is that performance rating is not limited by a design point or standardized operating conditions of the heat exchanger, but is realizable under flexible conditions.

A computational fluid dynamics and effectiveness-NTU based co-simulation approach for flow mal-distribution analysis in microchannel heat exchanger headers

International Nuclear Information System (INIS)

Huang, Long; Lee, Moon Soo; Saleh, Khaled; Aute, Vikrant; Radermacher, Reinhard

2014-01-01

Refrigerant flow mal-distribution is a practical challenge in most microchannel heat exchangers (MCHXs) applications. Geometry design, uneven heat transfer and pressure drop in the different microchannel tubes are three main reasons leading to the flow mal-distribution. To efficiently and accurately account for these three effects, a new MCHX co-simulation approach is proposed in this paper. The proposed approach combines a detailed header simulation based on computational fluid dynamics (CFD) and a robust effectiveness-based finite volume tube-side heat transfer and refrigerant flow modeling tool. The co-simulation concept is demonstrated on a ten-tube MCHX case study. Gravity effect and uneven airflow effect were numerically analyzed using both water and condensing R134a as the working fluids. The approach was validated against experimental data for an automotive R134a condenser. The inlet header was cut open after the experimental data had been collected. The detailed header geometry was reproduced using the proposed CFD header model. Good prediction accuracy was achieved compared to the experimental data. The presented co-simulation approach is capable of predicting detailed refrigerant flow behavior while accurately predicts the overall heat exchanger performance. - Highlights: •MCHX header flow distribution is analyzed by a co-simulation approach. •The proposed method is capable of simulating both single-phase and two-phase flow. •An actual header geometry is reproduced in the CFD header model. •The modeling work is experimentally validated with good accuracy. •Gravity effect and air side mal-distribution are accounted for

Fabrication and application of boron doped diamond BDD electrode in olive mill wastewater treatment in Jordan

Directory of Open Access Journals (Sweden)

Inshad Jum'h

2017-12-01

Full Text Available A boron doped diamond (BDD electrode was employed in an electrochemical reactor to oxidize the phenolic content of Jordanian olive mill wastewater. The BDD anode was fabricated using hot filament chemical vapor deposition on niobium and the morphology of the BDD electrode was characterized using an atomic force microscope. Then, electrolysis batch runs were carried out at laboratory scale to test the effect of different process parameters, namely, initial chemical oxygen demand (COD load (72.9, 33.8, and 0.18 g/L, the addition of Na2SO4 as supporting electrolyte, and adding NaCl along with Na2SO4, on the efficiency of the treatment process. The results were reported in terms of COD, color and turbidity removal, and pH variation. The experiments revealed that electrochemical oxidation using BDD significantly reduced the COD by 85% with no supporting electrolytes. It was observed that adding Na2SO4 with NaCl brought the COD removal to higher than 90% after 7 hours of treatment for COD loads of 72.9 and 33.8 g/L, and after 2 hours for a COD load of 0.18 g/L. Likewise, color was completely removed regardless of the initial COD load. The turbidity for samples with 72.9 and 33.8 g/L as COD load reached a minimal value of 2.5 and 1 NTU respectively.

Simultaneous wastewater treatment and biogas production using integrated anaerobic baffled reactor granular activated carbon from baker's yeast wastewater.

Science.gov (United States)

Pirsaheb, Meghdad; Mohamadi, Samira; Rahmatabadi, Sama; Hossini, Hooshyar; Motteran, Fabrício

2017-08-30

In this study, simultaneous degradation of organic matter and color removal from food processing industries wastewater using an integrated anaerobic baffled reactor granular activated carbon (IABRGAC) was investigated. Theretofore, effective parameters such as hydraulic retention time (HRT) and granular activated carbon (GAC) filling ratio were studied. The bioreactor was operated at 3, 4 and 5 d of HRT and GAC filling ratio of 20%, 35% and 50%. To analyze and optimize the independent operating variables, response surface methodology was applied. Operating condition was optimized for HRT (4 d) and GAC filling ratio (50%). Better COD (94.6%) and BOD (93.7%) removal efficiency occurred with loading COD of 15,000 mg/L, with diminished wastewater color around 54% and turbidity to 54 NTU. In addition, methane production, methane yielding rate (Y m ) and specific methanogenic activity (SMA) test in an integrated system were investigated. The system IABRGAC was able to generate a volumetric rate about 0.31 and 0.44 L/g COD removed d at the experimental condition. The Y m was between 0.31 and 0.44 L/g COD removed .d and SMA was between 0.13 and 0.38 g COD/g volatile suspended solid. Based on results it can be concluded that the IABRGAC to be a successful pretreatment for highstrength wastewater before discharging the final effluent to sewerage and aerobic treating processes.

Evaluation of Dissolved Air Flotation (DAF for Pretreatment of the Karoon River Water

Directory of Open Access Journals (Sweden)

Naeim Banisaeid

2007-09-01

Full Text Available The efficiency of a pilot dissolved air flotation (DAF unit is evaluated. It is the objective of the present study to determine the removal efficiency of DAF in removing turbidity and organic matter from theKaroonRiverfeeding a water treatment plant. Water quality investigations over the study period revealed that, thanks to the self-purification process in the river, the Karoon water quality is acceptable with respect to total organic carbon (TOC (never exceeding 2.89 mg/l but its turbidity has great fluctuations (from as low as 42 to 1,000 NTU due to the nature of the river. Its true color is in desirable conditions. Suspended solids removal efficiency of the pilot DAF unit varied from 38% to 95%, with an average level of 72%. The results from this study indicate that DAF removal efficiency is inversely related to the volume of inflow of solids into the system so that increasing TSS decreases removal efficiency. The high turbidity level in the absence of a primary sedimentation unit causes the flotation system to lose its desired efficiency. FAD cannot be, therefore, recommended for water treatment plants fed by the Karoon water unless a pretreatment unit is used. Furthermore, as FAD's TOC removal efficiency varies by up to 82%, and since part of the organic content includes volatile organic matter causing odors and undesirable taste, FAD is recommended as a complementary process in the treatment of high quality water.

A preliminary study of opuntia stricta as a coagulant for turbidity removal in surface waters

International Nuclear Information System (INIS)

Mukhtar, A.

2015-01-01

Natural polymers, extracted from plants, can be used as coagulants for water treatment in addition to metal salts and synthetic polymers. Natural materials may offer benefits such as local production, lesser health hazards and affordability for developing world. Opuntia stricta plant, a cactus specie native to Mexico, has been explored in this study for its efficacy as coagulant. Efficiency of Opuntia stricta was assessed on the basis of turbidity removal from lab prepared and surface water samples. The effect of water pH on its performance was also analyzed. The study results revealed that removal efficiency of Opuntia stricta for turbidity removal remains consistent within a wide pH range (pH 5 to 10), in contrast to other coagulants which are pH dependent. Furthermore, pH of the water remains constant during coagulation and pH adjustment may not be required for subsequent treatment processes, which is often needed in case metal coagulants are used. Residual turbidity below 20 NTU is conveniently achieved by using Opuntia stricta even when it is used at very low doses. Formation of exceptionally large flocs and their linear configuration reveals the possibility that mechanism of coagulation by Opuntia stricta is adsorption and inter-particle bridging. (author)

AN ADVANCED OXIDATION PROCESS : FENTON PROCESS

Directory of Open Access Journals (Sweden)

Engin GÜRTEKİN

2008-03-01

Full Text Available Biological wastewater treatment is not effective treatment method if raw wastewater contains toxic and refractory organics. Advanced oxidation processes are applied before or after biological treatment for the detoxification and reclamation of this kind of wastewaters. The advanced oxidation processes are based on the formation of powerful hydroxyl radicals. Among advanced oxidation processes Fenton process is one of the most promising methods. Because application of Fenton process is simple and cost effective and also reaction occurs in a short time period. Fenton process is applied for many different proposes. In this study, Fenton process was evaluated as an advanced oxidation process in wastewater treatment.

A study of the parameters affecting the effectiveness of Moringa oleifera in drinking water purification

Science.gov (United States)

Pritchard, M.; Craven, T.; Mkandawire, T.; Edmondson, A. S.; O'Neill, J. G.

The powder obtained from the seeds of the Moringa oleifera tree has been shown to be an effective primary coagulant for water treatment. When the seeds are dried, dehusked, crushed and added to water, the powder acts as a coagulant binding colloidal particles and bacteria to form agglomerated particles (flocs), which settle allowing the clarified supernatant to be poured off. Very little research has been undertaken on the parameters affecting the effectiveness of M. oleifera, especially in Malawi, for purification of drinking water and there is a great need for further testing in this area. Conclusive data needs to be compiled to demonstrate the effects of various water parameters have on the efficiency of the seeds. A parametric study was undertaken at Leeds Metropolitan University, UK, with the aim to establish the most appropriate dosing method; the optimum dosage for removal of turbidity; the influence of pH and temperature; together with the shelf life of the M. oleifera seeds. The study revealed that the most suitable dosing method was to mix the powder into a concentrated paste, hence forming a stock suspension. The optimum M. oleifera dose, for turbidity values between 40 and 200 NTU, ranged between 30 and 55 mg/l. With turbidity set at 130 NTU and a M. oleifera dose within the optimum range at 50 mg/l, pH levels were varied between 4 and 9. It was discovered that the coagulant performance was not too sensitive to pH fluctuations when conditions were within the optimum range. The most efficient coagulation, determined by the greatest reduction in turbidity, occurred at pH 6.5. Alkaline conditions were overall more favourable than acidic conditions; pH 9 had an efficiency of 65% of optimum, whilst at pH 5 the efficiency dropped to around 55%. The efficiency further dropped at pH 4, where the powder only produced results of around 10% of optimum conditions. A temperature range of 4-60 °C was studied in this research. Colder waters (<15 °C) were found to

Small Scale Direct Potable Reuse (DPR Project for a Remote Area

Directory of Open Access Journals (Sweden)

Jianhua Zhang

2017-02-01

Full Text Available An Advanced Water Treatment Plant (AWTP for potable water recycling in Davis Station Antarctica was trialed using secondary effluent at Selfs Point in Hobart, Tasmania, for nine months. The trials demonstrated the reliability of performance of a seven barrier treatment process consisting of ozonation, ceramic microfiltration (MF, biologically activated carbon, reverse osmosis, ultra-violet disinfection, calcite contactor and chlorination. The seven treatment barriers were required to meet the high log removal values (LRV required for pathogens in small systems during disease outbreak, and on-line verification of process performance was required for operation with infrequent operator attention. On-line verification of pathogen LRVs, a low turbidity filtrate of approximately 0.1 NTU (Nephelometric Turbidity Unit, no long-term fouling and no requirement for clean-in-place (CIP was achieved with the ceramic MF. A pressure decay test was also reliably implemented on the reverse osmosis system to achieve a 2 LRV for protozoa, and this barrier required only 2–3 CIP treatments each year. The ozonation process achieved 2 LRV for bacteria and virus with no requirement for an ozone residual, provided the ozone dose was >11.7 mg/L. Extensive screening using multi-residue gas chromatography–mass spectrometry (GC–MS and liquid chromatography–mass spectrometry (LC–MS database methods that can screen for more than 1200 chemicals found that few chemicals pass through the barriers to the final product and rejected (discharge water streams. The AWTP plant required 1.93 kWh/m3 when operated in the mode required for Davis Station and was predicted to require 1.27 kWh/m3 if scaled up to 10 ML/day. The AWTP will be shipped to Davis Station for further trials before possible implementation for water recycling. The process may have application in other small remote communities.

The consideration of dynamics and control in the design of heat exchanger networks

International Nuclear Information System (INIS)

Reimann, K.A.

1986-03-01

The heat exchanger network method is a way of abstracting the enthalpy and heat flows from the blueprints of a planned or existing processing plant. It enables a systematic design of a plant-wide heat recovery system which is optimal with regard to energy costs, capital costs and operational requirements. A heat exchanger network is a representation of all heat transfer relations between hot process streams and cold process streams within a plant. During the past ten years, the optimal design of heat exchanger networks (i.e. the optimal arrangement of heat transfer relations within a plant) has developed into a field of research of its own. Both, static methods ('interaction analysis') and dynamic methods ('process reaction curve analysis') from control theory have been used to explore the new field of heat exchanger network dynamics. As a major tool, an interactive, portable computer program for network simulation and controllability assessment has been developed (it is available as a design tool within the frame of the International Energy Agency). Based on the well-understood global parameters: effectiveness and NTU, which follow from the network design, some straightforward methods covering the following topics are presented: - 'paths' for control and disturbance signal transfer across the network, - locations of control bypasses around heat exchangers, and their capacity of emitting control signals or absorbing disturbances, - influence of the equipment besides the heat exchangers (which can be regarded as 'surrounding' the network, thus forming an 'associated' network). It has been found that networks which are designed according to the 'pinch-based' method have a potential for good controllability. It is shown how, using the freedoms given in the 'pinch-based' design and the above-mentioned methods, that potential is put into effect. (author)

Feasibility of turbidity removal by high-gradient superconducting magnetic separation.

Science.gov (United States)

Zeng, Hua; Li, Yiran; Xu, Fengyu; Jiang, Hao; Zhang, Weimin

2015-01-01

Several studies have focused on pollutant removal by magnetic seeding and high-gradient superconducting magnetic separation (HGSMS). However, few works reported the application of HGSMS for treating non-magnetic pollutants by an industrial large-scale system. The feasibility of turbidity removal by a 600 mm bore superconducting magnetic separation system was evaluated in this study. The processing parameters were evaluated by using a 102 mm bore superconducting magnetic separation system that was equipped with the same magnetic separation chamber that was used in the 600 mm bore system. The double-canister system was used to process water pollutants. Analytical grade magnetite was used as a magnetic seed and the turbidity of the simulated raw water was approximately 110 NTU, and the effects of polyaluminum chloride (PAC) and magnetic seeds on turbidity removal were evaluated. The use of more PAC and magnetic seeds had few advantages for the HGSMS at doses greater than 8 and 50 mg/l, respectively. A magnetic intensity of 5.0 T was beneficial for HGSMS, and increasing the flow rate through the steel wool matrix decreased the turbidity removal efficiency. In the breakthrough experiments, 90% of the turbidity was removed when 100 column volumes were not reached. The processing capacity of the 600 mm bore industry-scale superconducting magnetic separator for turbidity treatment was approximately 78.0 m(3)/h or 65.5 × 10(4) m(3)/a. The processing cost per ton of water for the 600 mm bore system was 0.1 $/t. Thus, the HGSMS separator could be used in the following special circumstances: (1) when adequate space is not available for traditional water treatment equipment, especially the sedimentation tank, and (2) when decentralized sewage treatment HGSMS systems are easier to transport and install.

Control system for technological processes in tritium processing plants with process analysis

International Nuclear Information System (INIS)

Retevoi, Carmen Maria; Stefan, Iuliana; Balteanu, Ovidiu; Stefan, Liviu; Bucur, Ciprian

2005-01-01

Integration of a large variety of installations and equipment into a unitary system for controlling the technological process in tritium processing nuclear facilities appears to be a rather complex approach particularly when experimental or new technologies are developed. Ensuring a high degree of versatility allowing easy modifications in configurations and process parameters is a major requirement imposed on experimental installations. The large amount of data which must be processed, stored and easily accessed for subsequent analyses imposes development of a large information network based on a highly integrated system containing the acquisition, control and technological process analysis data as well as data base system. On such a basis integrated systems of computation and control able to conduct the technological process could be developed as well protection systems for cases of failures or break down. The integrated system responds to the control and security requirements in case of emergency and of the technological processes specific to the industry that processes radioactive or toxic substances with severe consequences in case of technological failure as in the case of tritium processing nuclear plant. In order to lower the risk technological failure of these processes an integrated software, data base and process analysis system are developed, which, based on identification algorithm of the important parameters for protection and security systems, will display the process evolution trend. The system was checked on a existing plant that includes a removal tritium unit, finally used in a nuclear power plant, by simulating the failure events as well as the process. The system will also include a complete data base monitoring all the parameters and a process analysis software for the main modules of the tritium processing plant, namely, isotope separation, catalytic purification and cryogenic distillation

Markov Processes in Image Processing

Science.gov (United States)

Petrov, E. P.; Kharina, N. L.

2018-05-01

Digital images are used as an information carrier in different sciences and technologies. The aspiration to increase the number of bits in the image pixels for the purpose of obtaining more information is observed. In the paper, some methods of compression and contour detection on the basis of two-dimensional Markov chain are offered. Increasing the number of bits on the image pixels will allow one to allocate fine object details more precisely, but it significantly complicates image processing. The methods of image processing do not concede by the efficiency to well-known analogues, but surpass them in processing speed. An image is separated into binary images, and processing is carried out in parallel with each without an increase in speed, when increasing the number of bits on the image pixels. One more advantage of methods is the low consumption of energy resources. Only logical procedures are used and there are no computing operations. The methods can be useful in processing images of any class and assignment in processing systems with a limited time and energy resources.

Electrocoagulación aplicada al tratamiento de efluentes generadospor empresas de mantenimiento de motores.

Directory of Open Access Journals (Sweden)

Alicia Guevara

2011-05-01

Full Text Available La electrocoagulación es una operación que desestabiliza una emulsión y permite altos porcentajes de remoción de demanda química de oxígeno (DQO y turbiedad. En el presente trabajo se evaluó la electrocoagulación como técnica de tratamiento no convencional de efluentes generados por empresas de Mantenimiento de motores y para la evaluación de la operación se midieron los parámetros: DQO, tensoactivos, sólidos suspendidos y totales, turbiedad y concentración de aluminio, cobre y cinc. El efluente estudiado se caracterizó por ser altamente heterogéneo, así la DQO varió entre 10 500 mg/l y 14 700 mg/l. La turbiedad desde 619 NTU a 886 NTU. El rango de tensoactivos desde 86,6 mg/l a 221, 6 mg/l. La concentración inicial de aluminio fue 88 mg/l, de cobre fue 123 mg/l y de cinc fue 13 mg/l. La concentración inicial de sólidos suspendidos fue 340 mg/l y la concentración de sólidos totales fue 10 456 mg/l. En la investigación se establecieron los valores de las variables que influyen en la electrocoagulación para hacerla eficiente. El pH de operación que presenta mejores resultados es 9,7. La intensidad de corriente que se determinó como la más eficiente es de 1,8 A. Con esta intensidad de corriente se tiene una remoción de DQO de 32%, remoción de sólidos suspendidos de 98,3 %, remoción de turbiedad de 97,4 % y remoción de aluminio 88%, de cobre 87% y de cinc de 99%, El tiempo de residencia que requiere la operación es de 60 minutos.

Effective removal of microorganisms and biostimulants of wastewater by the application of various electrolytes

Energy Technology Data Exchange (ETDEWEB)

Srivastava, Jatin [Department of Environmental Sciences, Institute of Biosciences and Biotechnology, Chhatrapati Shahu Ji Maharaj University, Kalyanpur, Kanpur, Uttar Pradesh (India); Singh, Nandita [Biomass-Biology and Eco-Auditing Division, National Botanical Research Institute, Lucknow, Uttar Pradesh (India)

2007-04-15

A variety of electrolytes FeCl{sub 3}, CaCl{sub 2}, CuSO{sub 4}, Al{sub 2}(SO{sub 4}){sub 3}, and LaCl{sub 3} was investigated for their efficiency in removing biostimulants (phosphorous and nitrogen) to improve the water quality. Results show that the removal of PO{sub 4}{sup 3-} was achieved below the detection limit (BDL) by two electrolytes, CuSO{sub 4} and Al{sub 2}(SO{sub 4}){sub 3}, and up to 1.0 {+-} 0.0 mg/L by LaCl{sub 3} from a value of 15.0 mg/L, of the concentration of PO{sub 4}{sup 3-} in amended water. The turbidity was found to be removed significantly by FeCl{sub 3}, CuSO{sub 4}, and Al{sub 2}(SO{sub 4}){sub 3} by about 5.8 {+-} 2.6, 9.7 {+-} 1.0, and 5.4 {+-} 1.1 nephalometric turbidity unit (NTU), respectively. The removal of the members of Enterobacteriaceae viz., Escherichia coli, Enterobacter spp. Pseudomonas fluorescence, and Pseudomonas spp. was found almost in all the chemical precipitants but their removal was more significant in the water samples treated with CuSO{sub 4}, Al{sub 2}(SO{sub 4}){sub 3}, and LaCl{sub 3}. To achieve a complete removal and to sustain the after effects of precipitation, such as recurrence of algal growth, the combination of CuSO{sub 4} and Al{sub 2}(SO{sub 4}){sub 3} was investigated. Reduction in the turbidity from 30.83 to <2 NTU, phosphate ion from a value of 1.28 mg/L to BDL and ammonia ion from a value of 44.71 to 36.48 mg/L of natural pond water were observed after the treatment with CuSO{sub 4} and Al{sub 2}(SO{sub 4}){sub 3} in combination. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

Fingerprinting Persistent Turbidity in Sheep Creek Reservoir, Owhyee, Nevada

Science.gov (United States)

Ransom, R. N.; Hooper, R. L.; Kerner, D.; Nicols, S.

2007-12-01

Sheep Creek Reservoir near Owyhee, NV is historically a quality rainbow trout fishery. Persistent high-turbidity has been an issue since a major storm event in 2005 resulted in surface water runoff into the Reservoir. The high turbidity is adversely impacting the quality of the fishery. Initial turbidity measurements in 2005 were upwards of 80NTU and these numbers have only decreased to 30NTU over the past two summers. Field parameters indicate the turbidity is associated with high total suspended solids (TSS) and not algae. Five water samples collected from around the reservoir during June, 2007 indicated uniform TSS values in the range of 5 to 12mg/L and oriented powder x-ray diffraction(XRD) and transmission electron microscopy(TEM) analyses of suspended sediment shows very uniform suspended particulate mineralogy including smectite, mixed layer illite/smectite (I/S), discrete illite, lesser amounts of kaolin, sub-micron quartz and feldspar. Diatoms represent a ubiquitous but minor component of the suspended solids. Six soil samples collected from possible source areas around the reservoir were analyzed using both XRD and TEM to see if a source area for the suspended solids could be unambiguously identified. Soils on the east side of the reservoir contain smectite and mixed layer I/S but very little of the other clays. The less than 2 micron size fraction from soils collected from a playa on the topographic bench immediately to the west of the reservoir show a mineralogic finger-print essentially identical to the current suspended sediment. The suspended sediment probably originates on the bench to the west of the reservoir and cascades into the reservoir over the topographic break during extreme storm events. The topographic relief, short travel distance and lack of a suitable vegetated buffer zone to the west are all consistent with a primary persistent suspended sediment source from the west. Identification of the sediment source allows for design of a cost

Study Of The Physico-Chemical Water Quality Of The Companys Pumping Stations Chadian Water And Suburbs Of Manual Drilling Ndjamena

Directory of Open Access Journals (Sweden)

Mahamat Seid A.M

2015-08-01

Full Text Available Water for consumption requires excellent physical chemical and microbiological quality. This source of life is one of the most controlled food products. It must not only meet the quality requirements but also must comply vis- -vis a set of drinking water standards and must not contain any microorganism no noise and no substance presents a potential danger to human health. This work was performed in the city of Ndjamena and aims to assess the physico-chemical quality of the water pumping stations of the National Water Company in the city center and boreholes in human motor in neighborhoods peripheral devices. A total of 18 samples were collected including 9 in the city center and 9 others in the suburbs. On each sample were determined physico-chemical parameters potential of hydrogen pH temperature T electrical conductivity turbidity and calcium ions magnesium sulphates fluorides and nitrates. The results extend into the water pumping stations of ETS and manual drilling outlying districts respectively temperature 28.0 to 36.1 C and 29.5 to 30.3 C pH 6.5 to 8.5 and 6.3 to 7.6 electrical conductivity 201-671 amp297S cm and 136-533 amp297S cm turbidity NTU from 0.01 to 0.18 and 1.25 to 5 NTU calcium 54 to 268 mg L to 65-443 mg L magnesium 2.18 to 57 mg L and 15 to 90 mg L sulfates 2 to 47 mg L and 2 to 18mg L fluoride 0.0 to 0.61 mg L and 0.12 to 0.98 mg L and nitrate 1.5 to 18 2 mg L and 0.1 to 0.6 mg L. The results show that the contents of the parameters are consistent with the WHO standards for the quality of drinking water except calcium ions which their levels are high. Based on the parameters analyzed the quality of water pumping stations of SNE and manual drilling is acceptable.

CovalentDock Cloud: a web server for automated covalent docking.

Science.gov (United States)

Ouyang, Xuchang; Zhou, Shuo; Ge, Zemei; Li, Runtao; Kwoh, Chee Keong

2013-07-01

Covalent binding is an important mechanism for many drugs to gain its function. We developed a computational algorithm to model this chemical event and extended it to a web server, the CovalentDock Cloud, to make it accessible directly online without any local installation and configuration. It provides a simple yet user-friendly web interface to perform covalent docking experiments and analysis online. The web server accepts the structures of both the ligand and the receptor uploaded by the user or retrieved from online databases with valid access id. It identifies the potential covalent binding patterns, carries out the covalent docking experiments and provides visualization of the result for user analysis. This web server is free and open to all users at http://docking.sce.ntu.edu.sg/.

A Modified Entropy Generation Number for Heat Exchangers

Institute of Scientific and Technical Information of China (English)

无

1996-01-01

This paper demonstrates the difference between the entropy generation number method proposed by Bejian and the method of entropy generation per unit amount of heat transferred in analyzing the ther-modynamic performance of heat exchangers,points out the reason for leading to the above difference.A modified entropy generation number for evaluating the irreversibility of heat exchangers is proposed which is in consistent with the entropy generation per unit amount of heat transferred in entropy generation analysis.The entropy generated by friction is also investigated.Results show that when the entropy generated by friction in heat exchangers in taken into account,there is a minimum total entropy generation number while the NTU and the ratio of heat capacity rates vary.The existence of this minimum is the prerequisite of heat exchanger optimization.

The effects of season and sand mining activities on thermal regime and water quality in a large shallow tropical lake.

Science.gov (United States)

Sharip, Zati; Zaki, Ahmad Taqiyuddin Ahmad

2014-08-01

Thermal structure and water quality in a large and shallow lake in Malaysia were studied between January 2012 and June 2013 in order to understand variations in relation to water level fluctuations and in-stream mining activities. Environmental variables, namely temperature, turbidity, dissolved oxygen, pH, electrical conductivity, chlorophyll-A and transparency, were measured using a multi-parameter probe and a Secchi disk. Measurements of environmental variables were performed at 0.1 m intervals from the surface to the bottom of the lake during the dry and wet seasons. High water level and strong solar radiation increased temperature stratification. River discharges during the wet season, and unsustainable sand mining activities led to an increased turbidity exceeding 100 NTU, and reduced transparency, which changed the temperature variation and subsequently altered the water quality pattern.

Numerical analysis of the influence of circuit arrangement on a fin-and-tube condenser performance

Directory of Open Access Journals (Sweden)

Cesare Maria Joppolo

2015-09-01

Full Text Available In the present paper a model for the steady-state simulation of fin-and-tube condenser is developed. The model is based on a finite volume approach that divides each tube into small elemental volumes where mass, momentum and energy conservation equations are solved using the effectiveness-NTU method and with appropriate correlations for void fraction, friction factor and heat transfer coefficient calculation. The model is validated against experimental data on two small condensers finding that the calculated heat transfer rate and refrigerant-side pressure drop agree within ±5% and ±21% respectively to the experimental values. The model is then used to numerically analyse the impact of different circuit arrangements on the condenser heat transfer rate, refrigerant-side pressure drop and refrigerant charge.

Investigation of coagulation activity of natural coagulants from seeds of different leguminose species

Directory of Open Access Journals (Sweden)

Šćiban Marina B.

2005-01-01

Full Text Available The ability of seeds of plants: Phaseolus vulgaris, Robinia pseudoacacia Ceratonia siliqua and Amorpha fruticosa, to act as natural coagulants was tested using synthetic turbid water. This water was prepared by adding kaolin into tap water, just before the test. Active components were extracted from ground seeds with distilled water. The coagulation ability of this extract was assessed by the use of standard jar test measurements in water with various initial turbidity. Investigation of these natural coagulants was confirmed their positive coagulation activity. Of all plants that have been examined, the seed extract from Ceratonia siliqua appeared to be one of the most effective coagulants for water treatment. A dose of 20 mg/l of this coagulant resulted in 100% coagulation activity for clarification of water with 17.5 NTU initial turbidity.

Parametric study on design fractors for the SCS heat exchanger using the Taguchi method

International Nuclear Information System (INIS)

Kim, S. H.; Choi, B. S.; Yoon, J. H.; Jang, M. H.

2002-01-01

Using Taguchi method, design factors, i.e. control factors of the shutdown cooling heat exchanger were investigated to qualify the effect for the time elapsed after the beginning of the system operation. Levels of the control factors were selected from calculations based on the effectiveness-NTU method. From 18 simulations with the KDESCENT program, it was found that the performance of the system is greatly influenced by inlet temperature from the component cooling water at the shell side and mass flow rate of the reactor coolant at the tube side. The Taguchi method makes it possible to select the control factor that has to be controlled and designed with caution. The method gives the effective way to estimate the influence of each control factor to the system performance

Thinning spatial point processes into Poisson processes

DEFF Research Database (Denmark)

Møller, Jesper; Schoenberg, Frederic Paik

, and where one simulates backwards and forwards in order to obtain the thinned process. In the case of a Cox process, a simple independent thinning technique is proposed. In both cases, the thinning results in a Poisson process if and only if the true Papangelou conditional intensity is used, and thus can......This paper describes methods for randomly thinning certain classes of spatial point processes. In the case of a Markov point process, the proposed method involves a dependent thinning of a spatial birth-and-death process, where clans of ancestors associated with the original points are identified...... be used as a diagnostic for assessing the goodness-of-fit of a spatial point process model. Several examples, including clustered and inhibitive point processes, are considered....

Process validation for radiation processing

International Nuclear Information System (INIS)

Miller, A.

1999-01-01

Process validation concerns the establishment of the irradiation conditions that will lead to the desired changes of the irradiated product. Process validation therefore establishes the link between absorbed dose and the characteristics of the product, such as degree of crosslinking in a polyethylene tube, prolongation of shelf life of a food product, or degree of sterility of the medical device. Detailed international standards are written for the documentation of radiation sterilization, such as EN 552 and ISO 11137, and the steps of process validation that are described in these standards are discussed in this paper. They include material testing for the documentation of the correct functioning of the product, microbiological testing for selection of the minimum required dose and dose mapping for documentation of attainment of the required dose in all parts of the product. The process validation must be maintained by reviews and repeated measurements as necessary. This paper presents recommendations and guidance for the execution of these components of process validation. (author)

Comparison of Water Turbidity Removal Efficiencies of Moringa oleifera Seed Extract and Poly-aluminum Chloride

Directory of Open Access Journals (Sweden)

Bijan Bina

2007-03-01

Full Text Available Coagulation and flocculation are essential processes in water treatment plants. Metal salts such as aluminum sulphate and ferric chloride are commonly used in the coagulation process in Iran. Poly-aluminum chloride (PAC has been used recently in Baba-Sheykhali Water Treatment Plant in Isfahan. Synthetic coagulants have health problems associated with them and are additionally uneconomical for use in developing countries. In this study, PAC and Moringa oleifera seed extract were compared for their efficiency as coagulants. Moringa oleifera, locally called “oil gaz” in Iran, grows in southern parts of Iran. One variety of this tree, Moringa progeria, is indigenous to Iran. For the purposes of this study, lab experiments were performed using distilled water containing synthetic caoline. Four turbidity levels of 10, 50, 500, and1000 (NTU and four pH levels of 5, 6, 7, and 8 were used for the jar test. It was found that oleifera seed extract was capable of removing 98, 97, 89, and 55% of the turbidity in the four experiments at optimum concentration levels of 10-30 (mg/l for all four pH levels of 6 to 8, respectively. PAC, in contrast, removed 99, 98, 95, and 89% of the turbidity at optimum concentrations of 20-30 (mg/l for a pH level of 8. The results indicate that Moringa oleifera seed extract has little effect on pH level and enjoys higher removal efficiency for higher turbidity levels. Reducing pH level decreased PAC turbidity removal efficiency.

Thinning spatial point processes into Poisson processes

DEFF Research Database (Denmark)

Møller, Jesper; Schoenberg, Frederic Paik

2010-01-01

are identified, and where we simulate backwards and forwards in order to obtain the thinned process. In the case of a Cox process, a simple independent thinning technique is proposed. In both cases, the thinning results in a Poisson process if and only if the true Papangelou conditional intensity is used, and......In this paper we describe methods for randomly thinning certain classes of spatial point processes. In the case of a Markov point process, the proposed method involves a dependent thinning of a spatial birth-and-death process, where clans of ancestors associated with the original points......, thus, can be used as a graphical exploratory tool for inspecting the goodness-of-fit of a spatial point process model. Several examples, including clustered and inhibitive point processes, are considered....

Process correlation analysis model for process improvement identification.

Science.gov (United States)

Choi, Su-jin; Kim, Dae-Kyoo; Park, Sooyong

2014-01-01

Software process improvement aims at improving the development process of software systems. It is initiated by process assessment identifying strengths and weaknesses and based on the findings, improvement plans are developed. In general, a process reference model (e.g., CMMI) is used throughout the process of software process improvement as the base. CMMI defines a set of process areas involved in software development and what to be carried out in process areas in terms of goals and practices. Process areas and their elements (goals and practices) are often correlated due to the iterative nature of software development process. However, in the current practice, correlations of process elements are often overlooked in the development of an improvement plan, which diminishes the efficiency of the plan. This is mainly attributed to significant efforts and the lack of required expertise. In this paper, we present a process correlation analysis model that helps identify correlations of process elements from the results of process assessment. This model is defined based on CMMI and empirical data of improvement practices. We evaluate the model using industrial data.

Management of processes of electrochemical dimensional processing

Science.gov (United States)

Akhmetov, I. D.; Zakirova, A. R.; Sadykov, Z. B.

2017-09-01

In different industries a lot high-precision parts are produced from hard-processed scarce materials. Forming such details can only be acting during non-contact processing, or a minimum of effort, and doable by the use, for example, of electro-chemical processing. At the present stage of development of metal working processes are important management issues electrochemical machining and its automation. This article provides some indicators and factors of electrochemical machining process.

Chemical process engineering in the transuranium processing plant

International Nuclear Information System (INIS)

Collins, E.D.; Bigelow, J.E.

1976-01-01

Since operation of the Transuranium Processing Plant began, process changes have been made to counteract problems caused by equipment corrosion, to satisfy new processing requirements, and to utilize improved processes. The new processes, equipment, and techniques have been incorporated into a sequence of steps which satisfies all required processing functions

Managing Process Variants in the Process Life Cycle

NARCIS (Netherlands)

Hallerbach, A.; Bauer, Th.; Reichert, M.U.

2007-01-01

When designing process-aware information systems, often variants of the same process have to be specified. Each variant then constitutes an adjustment of a particular process to specific requirements building the process context. Current Business Process Management (BPM) tools do not adequately

Comparison of grey water treatment performance by a cascading sand filter and a constructed wetland.

Science.gov (United States)

Kadewa, W W; Le Corre, K; Pidou, M; Jeffrey, P J; Jefferson, B

2010-01-01

A novel unplanted vertical flow subsurface constructed wetland technology comprising three shallow beds (0.6 m length, 0.45 m width and 0.2 m depth) arranged in a cascading series and a standard single-pass Vertical Flow Planted Constructed Wetland (VFPCW, 6 m² and 0.7 m depth) were tested for grey water treatment. Particular focus was on meeting consent for published wastewater reuse parameters and removal of anionic surfactants. Treatment performance at two hydraulic loading rates (HLR) of 0.08, and 0.17 m³ m⁻² d⁻¹ were compared. Both technologies effectively removed more than 90% turbidity and more than 96% for organics with the prototype meeting the most stringent reuse standard of < 2 NTU and <10 mg/L. However, surfactant removal in the VFPCW was higher (76-85%) than in the prototype which only achieved more than 50% removal at higher loading rate. Generally, the prototype performed consistently better than the VFPCW except for surfactant removal. However, at higher loading rates, both systems did not meet the reuse standard of <1 mg L⁻¹ for anionic surfactants. This observation confirms that shallow beds provide a more oxidised environment leading to higher BOD₅ and COD removals. Presence of plants in the VFPCW led to higher anionic surfactant removal, through increased microbial and sorption processes.

The Equipment of Using AZOLLA for O2-Supplimentation and its Test

Science.gov (United States)

Liu, Xia-Shi; Chen, Min; Bian, Zu-Liang; Liu, Chung-Chu

The water-consuming amount in a long-term astro-navigation is large. In order to reduce the burden of water supply from Earth ground, the space station needs to resolve the problems of water supply. For this reason, the recovery and regeneration of urine solution of spacemen, and its utilization possess a key importance. Many investigations on this aspect have been reported. Our research based on "biological absorption-purification-UV photocatalytic oxidation" techniques with a relevant treating equipment that for a comprehensive treatment to fresh urine of spacemen has been created. In this equipment, the urine solution was used as the nutrient solution for the biological parts in ecological life ensurant system, after absorbing the nutrient, it was decomposed, metabolized and purified in some distance, and created a favorable condition for the follow-up oxidation treatment by UV-Photocatalytic Oxidation. After these two processes, the treated urine solution reached the GB5749-85 standard of water quality. Some main indexes are as table one. Chroma<5-15 Feculent degree-NTU-1.20-3 --5 Total rigidity-according to CaCO3-mg/L-3.60-450 N-NO3--mg/L-0.60-20 Soluble total solid-mg/L-543-1000 Bacterial gross-cfu/ml-13-100 Coliform group-No./L-<3-3 Key words-Photocatalytic Oxidation , Ultraviolet

Mass transfer performance comparison of two commonly used liquid desiccants: LiBr and LiCl aqueous solutions

International Nuclear Information System (INIS)

Liu, X.H.; Yi, X.Q.; Jiang, Y.

2011-01-01

Mass transfer performance of two commonly used liquid desiccants, LiBr aqueous solution and LiCl aqueous solution, is compared in this paper on the basis of the same solution temperature and surface vapor pressure. According to the analysis of the analytical solutions of heat and mass transfer processes, the key performance influencing factors are heat capacity ratio of air to desiccant m * and mass transfer unit NTU m . The heat capacities of the two liquid desiccants are about the same at same volumetric flow rate, and LiBr solution has higher density and smaller specific heat capacity. The variance of mass transfer unit with different operating conditions and liquid desiccants are derived based on the experimental results. In the condition of the same desiccant mass flow rate, the dehumidification performance of LiCl solution is better, and the regeneration performance of LiBr solution is a little better or almost the same as that of LiCl solution. In the condition of the same desiccant volumetric flow rate, the dehumidification performance of LiCl solution is a little better or about the same compared with LiBr solution, and the regeneration performance of LiBr solution is better. The COPs of the liquid desiccant systems using these two desiccants are similar; while LiCl solution costs 18% lower than LiBr solution at current Chinese price.

Impact of Thermal Annealing on Organic Photovoltaic Cells Using Regioisomeric Donor-Acceptor-Acceptor Molecules.

Science.gov (United States)

Zhang, Tao; Han, Han; Zou, Yunlong; Lee, Ying-Chi; Oshima, Hiroya; Wong, Ken-Tsung; Holmes, Russell J

2017-08-02

We report a promising set of donor-acceptor-acceptor (D-A-A) electron-donor materials based on coplanar thieno[3,2-b]/[2,3-b]indole, benzo[c][1,2,5]thiadiazole, and dicyanovinylene, which are found to show broadband absorption with high extinction coefficients. The role of the regioisomeric electron-donating thienoindole moiety on the physical and structural properties is examined. Bulk heterojunction (BHJ) organic photovoltaic cells (OPVs) based on the thieno[2,3-b]indole-based electron donor NTU-2, using C 70 as an electron acceptor, show a champion power conversion efficiency of 5.2% under AM 1.5G solar simulated illumination. This efficiency is limited by a low fill factor (FF), as has previously been the case in D-A-A systems. In order to identify the origin of the limited FF, further insight into donor layer charge-transport behavior is realized by examining planar heterojunction OPVs, with emphasis on the evolution of film morphology with thermal annealing. Compared to as-deposited OPVs that exhibit insufficient donor crystallinity, crystalline OPVs based on annealed thin films show an increase in the short-circuit current density, FF, and power conversion efficiency. These results suggest that that the crystallization of D-A-A molecules might not be realized spontaneously at room temperature and that further processing is needed to realize efficient charge transport in these materials.

[Development and application of a multi-species water quality model for water distribution systems with EPANET-MSX].

Science.gov (United States)

Sun, Fu; Chen, Ji-ning; Zeng, Si-yu

2008-12-01

A conceptual multi-species water quality model for water distribution systems was developed on the basis of the toolkit of the EPANET-MSX software. The model divided the pipe segment into four compartments including pipe wall, biofilm, boundary layer and bulk liquid. The involved processes were substrate utilization and microbial growth, decay and inactivation of microorganisms, mass transfer of soluble components through the boundary layer, adsorption and desorption of particular components between bulk liquid and biofilm, oxidation and halogenation of organic matter by residual chlorine, and chlorine consumption by pipe wall. The fifteen simulated variables included the seven common variables both in the biofilm and in the bulk liquid, i.e. soluble organic matter, particular organic matter, ammonia nitrogen, residual chlorine, heterotrophic bacteria, autotrophic bacteria and inert solids, as well as biofilm thickness on the pipe wall. The model was validated against the data from a series of pilot experiments, and the simulation accuracy for residual chlorine and turbidity were 0.1 mg/L and 0.3 NTU respectively. A case study showed that the model could reasonably reflect the dynamic variation of residual chlorine and turbidity in the studied water distribution system, while Monte Carlo simulation, taking into account both the variability of finished water from the waterworks and the uncertainties of model parameters, could be performed to assess the violation risk of water quality in the water distribution system.

Using Potato Peels as a Natural Coagulant in Drinking Water Treatment Plant “La Diana”

Directory of Open Access Journals (Sweden)

Ludyng Natalia Alvarado Carmona

2012-06-01

Full Text Available The following thesis presents the results of an analysis of experimental type, since residues of potato processing are not taken advantage of the best way by industries, causing organic waste and a bad use of biomass. That is why you want to evaluate their power coagulant in potable water treatment. Suspended particles impart undesirable color and turbidity superficial surface waters. Using chemicals such as aluminum sulfate can remove a significant proportion of the suspended solids, clarifying drinking water for subsequent stabilization. In this study we compared mixtures potato skins and aluminum sulphate, to evaluate which formulation is most suitable as coagulating agent in the treatment of drinking water, maintaining its characteristics of pH, color and turbidity. Through jar testing determined the optimal dose of aluminum sulfate ( 8 mg / L, standard formulation , in clarifying water sample Cane River and the gorge red (color of 41 UPC , 2 NTU turbidity and pH 7.76 and compared with other formulations of potato skins and aluminum sulfate. The results indicate that the greatest reduction in color was obtained with treatment 3 (2.5 g potato peel and similarly for the pH (7.46, thus the results of these two parameters are within the values required by the standard. Turbidity removal was the same in all treatments

Applications of Process Synthesis: Moving from Conventional Chemical Processes towards Biorefinery Processes

DEFF Research Database (Denmark)

Yuan, Zhihong; Chen, Bingzhen; Gani, Rafiqul

2013-01-01

Concerns about diminishing petroleum reserves, enhanced worldwide demand for fuels and fluctuations in the global oil market, together with climate change and national security have promoted many initiatives for exploring alternative, non-petroleum based processes. Among these initiatives......, biorefinery processes for converting biomass-derived carbohydrates into transportation fuels and chemicals are now gaining more and more attention from both academia and industry. Process synthesis, which has played a vital role for the development, design and operation of (petro) chemical processes, can...

Visualizing the process of process modeling with PPMCharts

NARCIS (Netherlands)

Claes, J.; Vanderfeesten, I.T.P.; Pinggera, J.; Reijers, H.A.; Weber, B.; Poels, G.; La Rosa, M.; Soffer, P.

2013-01-01

In the quest for knowledge about how to make good process models, recent research focus is shifting from studying the quality of process models to studying the process of process modeling (often abbreviated as PPM) itself. This paper reports on our efforts to visualize this specific process in such

Design of pulsed perforated-plate columns for industrial scale mass transfer applications - present experience and the need for a model based approach

International Nuclear Information System (INIS)

Roy, Amitava

2010-01-01

Mass transfer is a vital unit operation in the processing of spent nuclear fuel in the backend of closed fuel cycle and Pulsed perforated plate extraction columns are used as mass transfer device for more than five decades. The pulsed perforated plate column is an agitated differential contactor, which has wide applicability due to its simplicity, high mass transfer efficiency, high through put, suitability for maintenance free remote operation, ease of cleaning/decontamination and cost effectiveness. Design of pulsed columns are based on a model proposed to describe the hydrodynamics and mass transfer. In equilibrium stage model, the HETS values are obtained from pilot plant experiments and then scaled empirically to design columns for industrial application. The dispersion model accounts for mass transfer kinetics and back-mixing. The drop population balance model can describe complex hydrodynamics of dispersed phase, that is, drop formation, break-up and drop-to-drop interactions. In recent years, significant progress has been made to model pulsed columns using CFD, which provides complete mathematical description of hydrodynamics in terms of spatial distribution of flow fields and 3D visualization. Under the condition of pulsation, the poly-dispersed nature of turbulent droplet swarm renders modeling difficult. In the absence of industry acceptance of proposed models, the conventional chemical engineering practice is to use HETS-NTS concept or HTU-NTU approach to design extraction columns. The practicability of HTU-NTU approach has some limitations due to the lack of experimental data on individual film mass transfer coefficients. Presently, the HETS-NTS concept has been used for designing the columns, which has given satisfactory performance. The design objective is mainly to arrive at the diameter and height of the mass transfer section for a specific plate geometry, fluid properties and pulsing condition to meet the intended throughput (capacity) and mass

Process Intensification: A Perspective on Process Synthesis

DEFF Research Database (Denmark)

Lutze, Philip; Gani, Rafiqul; Woodley, John

2010-01-01

In recent years, process intensification (PI) has attracted considerable academic interest as a potential means for process improvement, to meet the increasing demands for sustainable production. A variety of intensified operations developed in academia and industry creates a large number...... of options to potentially improve the process but to identify the set of feasible solutions for PI in which the optimal can be found takes considerable resources. Hence, a process synthesis tool to achieve PI would potentially assist in the generation and evaluation of PI options. Currently, several process...... design tools with a clear focus on specific PI tasks exist. Therefore, in this paper, the concept of a general systematic framework for synthesis and design of PI options in hierarchical steps through analyzing an existing process, generating PI options in a superstructure and evaluating intensified...

Perceptual Processing Affects Conceptual Processing

Science.gov (United States)

van Dantzig, Saskia; Pecher, Diane; Zeelenberg, Rene; Barsalou, Lawrence W.

2008-01-01

According to the Perceptual Symbols Theory of cognition (Barsalou, 1999), modality-specific simulations underlie the representation of concepts. A strong prediction of this view is that perceptual processing affects conceptual processing. In this study, participants performed a perceptual detection task and a conceptual property-verification task…

A process insight repository supporting process optimization

OpenAIRE

Vetlugin, Andrey

2012-01-01

Existing solutions for analysis and optimization of manufacturing processes, such as online analysis processing or statistical calculations, have shortcomings that limit continuous process improvements. In particular, they lack means of storing and integrating the results of analysis. This makes the valuable information that can be used for process optimizations used only once and then disposed. The goal of the Advanced Manufacturing Analytics (AdMA) research project is to design an integrate...

Two-stage process analysis using the process-based performance measurement framework and business process simulation

NARCIS (Netherlands)

Han, K.H.; Kang, J.G.; Song, M.S.

2009-01-01

Many enterprises have recently been pursuing process innovation or improvement to attain their performance goals. To align a business process with enterprise performances, this study proposes a two-stage process analysis for process (re)design that combines the process-based performance measurement

Continuous Correctness of Business Processes Against Process Interference

NARCIS (Netherlands)

van Beest, Nick; Bucur, Doina

2013-01-01

In distributed business process support environments, process interference from multiple stakeholders may cause erroneous process outcomes. Existing solutions to detect and correct interference at runtime employ formal verification and the automatic generation of intervention processes at runtime.

Process mining: making knowledge discovery process centric

NARCIS (Netherlands)

Aalst, van der W.M.P.

2011-01-01

Recently, the Task Force on Process Mining released the Process Mining Manifesto. The manifesto is supported by 53 organizations and 77 process mining experts contributed to it. The active contributions from end-users, tool vendors, consultants, analysts, and researchers illustrate the growing

Multi-dimension feature fusion for action recognition

Science.gov (United States)

Dong, Pei; Li, Jie; Dong, Junyu; Qi, Lin

2018-04-01

Typical human actions last several seconds and exhibit characteristic spatio-temporal structure. The challenge for action recognition is to capture and fuse the multi-dimension information in video data. In order to take into account these characteristics simultaneously, we present a novel method that fuses multiple dimensional features, such as chromatic images, depth and optical flow fields. We built our model based on the multi-stream deep convolutional networks with the help of temporal segment networks and extract discriminative spatial and temporal features by fusing ConvNets towers multi-dimension, in which different feature weights are assigned in order to take full advantage of this multi-dimension information. Our architecture is trained and evaluated on the currently largest and most challenging benchmark NTU RGB-D dataset. The experiments demonstrate that the performance of our method outperforms the state-of-the-art methods.

F-Area Acid/Caustic Basin groundwater monitoring report. Second quarter 1994

International Nuclear Information System (INIS)

1994-09-01

During second quarter 1994, samples from the FAC monitoring wells at the F-Area Acid/Caustic Basin were collected and analyzed for herbicides/pesticides, indicator parameters, metals, nitrate, radionuclide indicators, volatile organic compounds, and other constituents. Piezometer FAC 5P and monitoring well FAC 6 were dry and could not be sampled. Analytical results that exceeded final Primary Drinking Water Standards (PDWS), other Savannah River Site (SRS) Flag 2 criteria, or the SRS turbidity standard of 50 NTU during the quarter were as follows: gross alpha exceeded the final PDWS and aluminum, iron, manganese, and total organic halogens exceeded the SRS Flag 2 criteria in one or more of the FAC wells. Turbidity exceeded the SRS standard in well FAC 3. Groundwater flow direction and rate in the water table beneath the F-Area Acid/Caustic Basin were similar to past quarters

Physico-chemical properties of drinking water available in educational institutes of karachi city

International Nuclear Information System (INIS)

Asadullah, A.; Nisa, K.; Khan, S.I.

2013-01-01

in order to investigate the physic-chemical quality, 780 water samples were collected from 490 educational institutes located in various areas of Karachi, during the period of May to September 2005. The parameters include pH, turbidity, total dissolve solids (TDS), hardness and conductivity that were varied from 3.2 to 8.7, 0.2 to 3.1 NTU (nephelometric turbidity unit), 79 to 1066 ppm, 69 to 558ppm and 96 to 1775 mu S/cm, respectively. On the basis of pH 6%, taste 2.1%, turbidity 0%, TDS 2.5% and hardness 1.3%, of the samples were found out of acceptable limits of World Health Organisation (WHO) guidelines. Moreover, the conductivity of the studied waters was found to be the multiple of 0.6001 to that of TDS (R/sup 2/ = 0.987) when regression model was established. (author)

Automatic control of the effluent turbidity from a chemically enhanced primary treatment with microsieving.

Science.gov (United States)

Väänänen, J; Memet, S; Günther, T; Lilja, M; Cimbritz, M; la Cour Jansen, J

2017-10-01

For chemically enhanced primary treatment (CEPT) with microsieving, a feedback proportional integral controller combined with a feedforward compensator was used in large pilot scale to control effluent water turbidity to desired set points. The effluent water turbidity from the microsieve was maintained at various set points in the range 12-80 NTU basically independent for a number of studied variations in influent flow rate and influent wastewater compositions. Effluent turbidity was highly correlated with effluent chemical oxygen demand (COD). Thus, for CEPT based on microsieving, controlling the removal of COD was possible. Thereby incoming carbon can be optimally distributed between biological nitrogen removal and anaerobic digestion for biogas production. The presented method is based on common automation and control strategies; therefore fine tuning and optimization for specific requirements are simplified compared to model-based dosing control.

Business process model repositories : efficient process retrieval

NARCIS (Netherlands)

Yan, Z.

2012-01-01

As organizations increasingly work in process-oriented manner, the number of business process models that they develop and have to maintain increases. As a consequence, it has become common for organizations to have collections of hundreds or even thousands of business process models. When a

Aerodynamic isotope separation processes for uranium enrichment: process requirements

International Nuclear Information System (INIS)

Malling, G.F.; Von Halle, E.

1976-01-01

The pressing need for enriched uranium to fuel nuclear power reactors, requiring that as many as ten large uranium isotope separation plants be built during the next twenty years, has inspired an increase of interest in isotope separation processes for uranium enrichment. Aerodynamic isotope separation processes have been prominently mentioned along with the gas centrifuge process and the laser isotope separation methods as alternatives to the gaseous diffusion process, currently in use, for these future plants. Commonly included in the category of aerodynamic isotope separation processes are: (a) the separation nozzle process; (b) opposed gas jets; (c) the gas vortex; (d) the separation probes; (e) interacting molecular beams; (f) jet penetration processes; and (g) time of flight separation processes. A number of these aerodynamic isotope separation processes depend, as does the gas centrifuge process, on pressure diffusion associated with curved streamlines for the basic separation effect. Much can be deduced about the process characteristics and the economic potential of such processes from a simple and elementary process model. In particular, the benefit to be gained from a light carrier gas added to the uranium feed is clearly demonstrated. The model also illustrates the importance of transient effects in this class of processes

Business Process Innovation using the Process Innovation Laboratory

DEFF Research Database (Denmark)

Møller, Charles

for practical applications has not been identified. The aim of this paper is to establish a conceptual framework for business process innovation in the supply chain based on advanced enterprise systems. The main approach to business process innovation in this context is to create a new methodology for exploring...... process models and patterns of applications. The paper thus presents a new concept for business process innovation called the process innovation laboratory a.k.a. the ?-Lab. The ?-Lab is a comprehensive framework for BPI using advanced enterprise systems. The ?-Lab is a collaborative workspace...... for experimenting with process models and an explorative approach to study integrated modeling in a controlled environment. The ?-Lab facilitates innovation by using an integrated action learning approach to process modeling including contemporary technological, organizational and business perspectives....

Discovering Reference Process Models by Mining Process Variants

NARCIS (Netherlands)

Li, C.; Reichert, M.U.; Wombacher, Andreas

Recently, a new generation of adaptive Process-Aware Information Systems (PAIS) has emerged, which allows for dynamic process and service changes (e.g., to insert, delete, and move activities and service executions in a running process). This, in turn, has led to a large number of process variants

BUSINESS PROCESS REENGINEERING AS THE METHOD OF PROCESS MANAGEMENT

Directory of Open Access Journals (Sweden)

O. Honcharova

2013-09-01

Full Text Available The article is devoted to the analysis of process management approach. The main understanding of process management approach has been researched in the article. The definition of process and process management has been given. Also the methods of business process improvement has been analyzed, among them are fast-analysis solution technology (FAST, benchmarking, reprojecting and reengineering. The main results of using business process improvement have been described in figures of reducing cycle time, costs and errors. Also the tasks of business process reengineering have been noticed. The main stages of business process reengineering have been noticed. The main efficiency results of business process reengineering and its success factors have been determined.

Fundamentals of process intensification: A process systems engineering view

DEFF Research Database (Denmark)

Babi, Deenesh Kavi; Sales Cruz, Alfonso Mauricio; Gani, Rafiqul

2016-01-01

This chapter gives an overview of the fundamentals of process intensification from a process systems engineering point of view. The concept of process intensification, including process integration, is explained together with the drivers for applying process intensification, which can be achieved...

Idaho Chemical Processing Plant Process Efficiency improvements

International Nuclear Information System (INIS)

Griebenow, B.

1996-03-01

In response to decreasing funding levels available to support activities at the Idaho Chemical Processing Plant (ICPP) and a desire to be cost competitive, the Department of Energy Idaho Operations Office (DOE-ID) and Lockheed Idaho Technologies Company have increased their emphasis on cost-saving measures. The ICPP Effectiveness Improvement Initiative involves many activities to improve cost effectiveness and competitiveness. This report documents the methodology and results of one of those cost cutting measures, the Process Efficiency Improvement Activity. The Process Efficiency Improvement Activity performed a systematic review of major work processes at the ICPP to increase productivity and to identify nonvalue-added requirements. A two-phase approach was selected for the activity to allow for near-term implementation of relatively easy process modifications in the first phase while obtaining long-term continuous improvement in the second phase and beyond. Phase I of the initiative included a concentrated review of processes that had a high potential for cost savings with the intent of realizing savings in Fiscal Year 1996 (FY-96.) Phase II consists of implementing long-term strategies too complex for Phase I implementation and evaluation of processes not targeted for Phase I review. The Phase II effort is targeted for realizing cost savings in FY-97 and beyond

Process Accounting

OpenAIRE

Gilbertson, Keith

2002-01-01

Standard utilities can help you collect and interpret your Linux system's process accounting data. Describes the uses of process accounting, standard process accounting commands, and example code that makes use of process accounting utilities.

Modeling of biopharmaceutical processes. Part 2: Process chromatography unit operation

DEFF Research Database (Denmark)

Kaltenbrunner, Oliver; McCue, Justin; Engel, Philip

2008-01-01

Process modeling can be a useful tool to aid in process development, process optimization, and process scale-up. When modeling a chromatography process, one must first select the appropriate models that describe the mass transfer and adsorption that occurs within the porous adsorbent. The theoret......Process modeling can be a useful tool to aid in process development, process optimization, and process scale-up. When modeling a chromatography process, one must first select the appropriate models that describe the mass transfer and adsorption that occurs within the porous adsorbent...

Generalized Ornstein-Uhlenbeck processes and associated self-similar processes

CERN Document Server

Lim, S C

2003-01-01

We consider three types of generalized Ornstein-Uhlenbeck processes: the stationary process obtained from the Lamperti transformation of fractional Brownian motion, the process with stretched exponential covariance and the process obtained from the solution of the fractional Langevin equation. These stationary Gaussian processes have many common properties, such as the fact that their local covariances share a similar structure and they exhibit identical spectral densities at large frequency limit. In addition, the generalized Ornstein-Uhlenbeck processes can be shown to be local stationary representations of fractional Brownian motion. Two new self-similar Gaussian processes, in addition to fractional Brownian motion, are obtained by applying the (inverse) Lamperti transformation to the generalized Ornstein-Uhlenbeck processes. We study some of the properties of these self-similar processes such as the long-range dependence. We give a simulation of their sample paths based on numerical Karhunan-Loeve expansi...

Generalized Ornstein-Uhlenbeck processes and associated self-similar processes

International Nuclear Information System (INIS)

Lim, S C; Muniandy, S V

2003-01-01

We consider three types of generalized Ornstein-Uhlenbeck processes: the stationary process obtained from the Lamperti transformation of fractional Brownian motion, the process with stretched exponential covariance and the process obtained from the solution of the fractional Langevin equation. These stationary Gaussian processes have many common properties, such as the fact that their local covariances share a similar structure and they exhibit identical spectral densities at large frequency limit. In addition, the generalized Ornstein-Uhlenbeck processes can be shown to be local stationary representations of fractional Brownian motion. Two new self-similar Gaussian processes, in addition to fractional Brownian motion, are obtained by applying the (inverse) Lamperti transformation to the generalized Ornstein-Uhlenbeck processes. We study some of the properties of these self-similar processes such as the long-range dependence. We give a simulation of their sample paths based on numerical Karhunan-Loeve expansion

From Process Understanding to Process Control

NARCIS (Netherlands)

Streefland, M.

2010-01-01

A licensed pharmaceutical process is required to be executed within the validated ranges throughout the lifetime of product manufacturing. Changes to the process usually require the manufacturer to demonstrate that the safety and efficacy of the product remains unchanged. Recent changes in the

Integrated Process Modeling-A Process Validation Life Cycle Companion.

Science.gov (United States)

Zahel, Thomas; Hauer, Stefan; Mueller, Eric M; Murphy, Patrick; Abad, Sandra; Vasilieva, Elena; Maurer, Daniel; Brocard, Cécile; Reinisch, Daniela; Sagmeister, Patrick; Herwig, Christoph

2017-10-17

During the regulatory requested process validation of pharmaceutical manufacturing processes, companies aim to identify, control, and continuously monitor process variation and its impact on critical quality attributes (CQAs) of the final product. It is difficult to directly connect the impact of single process parameters (PPs) to final product CQAs, especially in biopharmaceutical process development and production, where multiple unit operations are stacked together and interact with each other. Therefore, we want to present the application of Monte Carlo (MC) simulation using an integrated process model (IPM) that enables estimation of process capability even in early stages of process validation. Once the IPM is established, its capability in risk and criticality assessment is furthermore demonstrated. IPMs can be used to enable holistic production control strategies that take interactions of process parameters of multiple unit operations into account. Moreover, IPMs can be trained with development data, refined with qualification runs, and maintained with routine manufacturing data which underlines the lifecycle concept. These applications will be shown by means of a process characterization study recently conducted at a world-leading contract manufacturing organization (CMO). The new IPM methodology therefore allows anticipation of out of specification (OOS) events, identify critical process parameters, and take risk-based decisions on counteractions that increase process robustness and decrease the likelihood of OOS events.

PC image processing

International Nuclear Information System (INIS)

Hwa, Mok Jin Il; Am, Ha Jeng Ung

1995-04-01

This book starts summary of digital image processing and personal computer, and classification of personal computer image processing system, digital image processing, development of personal computer and image processing, image processing system, basic method of image processing such as color image processing and video processing, software and interface, computer graphics, video image and video processing application cases on image processing like satellite image processing, color transformation of image processing in high speed and portrait work system.

Meat Processing.

Science.gov (United States)

Legacy, Jim; And Others

This publication provides an introduction to meat processing for adult students in vocational and technical education programs. Organized in four chapters, the booklet provides a brief overview of the meat processing industry and the techniques of meat processing and butchering. The first chapter introduces the meat processing industry and…

Process for improving metal production in steelmaking processes

Science.gov (United States)

Pal, Uday B.; Gazula, Gopala K. M.; Hasham, Ali

1996-01-01

A process and apparatus for improving metal production in ironmaking and steelmaking processes is disclosed. The use of an inert metallic conductor in the slag containing crucible and the addition of a transition metal oxide to the slag are the disclosed process improvements.

Genetic Process Mining: Alignment-based Process Model Mutation

NARCIS (Netherlands)

Eck, van M.L.; Buijs, J.C.A.M.; Dongen, van B.F.; Fournier, F.; Mendling, J.

2015-01-01

The Evolutionary Tree Miner (ETM) is a genetic process discovery algorithm that enables the user to guide the discovery process based on preferences with respect to four process model quality dimensions: replay fitness, precision, generalization and simplicity. Traditionally, the ETM algorithm uses

Business process modeling for processing classified documents using RFID technology

Directory of Open Access Journals (Sweden)

Koszela Jarosław

2016-01-01

Full Text Available The article outlines the application of the processing approach to the functional description of the designed IT system supporting the operations of the secret office, which processes classified documents. The article describes the application of the method of incremental modeling of business processes according to the BPMN model to the description of the processes currently implemented (“as is” in a manual manner and target processes (“to be”, using the RFID technology for the purpose of their automation. Additionally, the examples of applying the method of structural and dynamic analysis of the processes (process simulation to verify their correctness and efficiency were presented. The extension of the process analysis method is a possibility of applying the warehouse of processes and process mining methods.

Novel process windows, part 1: Boosted micro process technology

NARCIS (Netherlands)

Hessel, V.; Wang, Q.

2011-01-01

Novel Process Windows (NPW) is the use of highly intensified, unusual and typically harsh process conditions to boost micro process technology and flow chemistry for the production of high-added value fine chemicals, pharmaceuticals, etc.. It is far from conventional processing and also from

Hyperspectral Sensing for Turbid Water Quality Monitoring in Freshwater Rivers: Empirical Relationship between Reflectance and Turbidity and Total Solids

Directory of Open Access Journals (Sweden)

Jiunn-Lin Wu

2014-11-01

Full Text Available Total suspended solid (TSS is an important water quality parameter. This study was conducted to test the feasibility of the band combination of hyperspectral sensing for inland turbid water monitoring in Taiwan. The field spectral reflectance in the Wu river basin of Taiwan was measured with a spectroradiometer; the water samples were collected from the different sites of the Wu river basin and some water quality parameters were analyzed on the sites (in situ as well as brought to the laboratory for further analysis. To obtain the data set for this study, 160 in situ sample observations were carried out during campaigns from August to December, 2005. The water quality results were correlated with the reflectivity to determine the spectral characteristics and their relationship with turbidity and TSS. Furthermore, multiple-regression (MR and artificial neural network (ANN were used to model the transformation function between TSS concentration and turbidity levels of stream water, and the radiance measured by the spectroradiometer. The value of the turbidity and TSS correlation coefficient was 0.766, which implies that turbidity is significantly related to TSS in the Wu river basin. The results indicated that TSS and turbidity are positively correlated in a significant way across the entire spectrum, when TSS concentration and turbidity levels were under 800 mg·L−1 and 600 NTU, respectively. Optimal wavelengths for the measurements of TSS and turbidity are found in the 700 and 900 nm range, respectively. Based on the results, better accuracy was obtained only when the ranges of turbidity and TSS concentration were less than 800 mg·L−1 and less than 600 NTU, respectively and used rather than using whole dataset (R2 = 0.93 versus 0.88 for turbidity and R2 = 0.83 versus 0.58 for TSS. On the other hand, the ANN approach can improve the TSS retrieval using MR. The accuracy of TSS estimation applying ANN (R2 = 0.66 was better than with the MR

Potential environmental drivers of a regional blue mussel mass mortality event (winter of 2014, Breton Sound, France)

Science.gov (United States)

Polsenaere, Pierre; Soletchnik, Patrick; Le Moine, Olivier; Gohin, Francis; Robert, Stéphane; Pépin, Jean-François; Stanisière, Jean-Yves; Dumas, Franck; Béchemin, Christian; Goulletquer, Philippe

2017-05-01

In the context of global change, increasing mariculture production has raised particular concerns regarding its environmental impact and sustainability. Molluscs and particularly blue mussel account for a significant part of this total production. Although blue mussels are considered to be pretty resilient to environmental disturbances, we report in this study an unprecedented mussel mortality event that occurred during the winter of 2014 in the Breton Sound. 9000 metric tonnes of mussels were lost and mortality rates up to 100% were recorded at some farming areas. Through a coupling approach, the present work aims to better understand the potential environmental drivers associated with those mortalities. Firstly, we analysed long-term in situ and satellite data from environmental monitoring networks (available since 1998) to characterize the variability of seawater masses of the sound during the winter of 2014. Secondly, we used modelling simulations to study the possible relationship between seawater hydrodynamics and observed spatio-temporal patterns of mussel mortalities. From January to April 2014 at the long-line culture site where mortalities started, seawater temperatures ranged from 8.3 to 13.3 °C (10.2 ± 0.8 °C). Salinity and turbidity values showed successive and short drops (below 16; 29.3 ± 2.3) and numerous peaks (above 70 NTU; 17.4 ± 13.4 NTU) respectively. Winter conditions of 2014 were encountered along the entire French Atlantic coastline and linked to the sixth highest positive North Atlantic Oscillation (NAO +) index recorded since 1865. These particular environmental variations characterized the winter of 2014 but also others whereas no comparable mussel mortality rates were reported. Exact causes of the 2014 mortality event are still unknown but we showed these environmental variations could not alone be responsible. These have likely affected the sensitivity of the blue mussel populations that were already weakened by early spawning

Hyperspectral sensing for turbid water quality monitoring in freshwater rivers: Empirical relationship between reflectance and turbidity and total solids.

Science.gov (United States)

Wu, Jiunn-Lin; Ho, Chung-Ru; Huang, Chia-Ching; Srivastav, Arun Lal; Tzeng, Jing-Hua; Lin, Yao-Tung

2014-11-28

Total suspended solid (TSS) is an important water quality parameter. This study was conducted to test the feasibility of the band combination of hyperspectral sensing for inland turbid water monitoring in Taiwan. The field spectral reflectance in the Wu river basin of Taiwan was measured with a spectroradiometer; the water samples were collected from the different sites of the Wu river basin and some water quality parameters were analyzed on the sites (in situ) as well as brought to the laboratory for further analysis. To obtain the data set for this study, 160 in situ sample observations were carried out during campaigns from August to December, 2005. The water quality results were correlated with the reflectivity to determine the spectral characteristics and their relationship with turbidity and TSS. Furthermore, multiple-regression (MR) and artificial neural network (ANN) were used to model the transformation function between TSS concentration and turbidity levels of stream water, and the radiance measured by the spectroradiometer. The value of the turbidity and TSS correlation coefficient was 0.766, which implies that turbidity is significantly related to TSS in the Wu river basin. The results indicated that TSS and turbidity are positively correlated in a significant way across the entire spectrum, when TSS concentration and turbidity levels were under 800 mg·L(-1) and 600 NTU, respectively. Optimal wavelengths for the measurements of TSS and turbidity are found in the 700 and 900 nm range, respectively. Based on the results, better accuracy was obtained only when the ranges of turbidity and TSS concentration were less than 800 mg·L(-1) and less than 600 NTU, respectively and used rather than using whole dataset (R(2) = 0.93 versus 0.88 for turbidity and R(2) = 0.83 versus 0.58 for TSS). On the other hand, the ANN approach can improve the TSS retrieval using MR. The accuracy of TSS estimation applying ANN (R(2) = 0.66) was better than with the MR approach (R

Cognitive Processes in Discourse Comprehension: Passive Processes, Reader-Initiated Processes, and Evolving Mental Representations

Science.gov (United States)

van den Broek, Paul; Helder, Anne

2017-01-01

As readers move through a text, they engage in various types of processes that, if all goes well, result in a mental representation that captures their interpretation of the text. With each new text segment the reader engages in passive and, at times, reader-initiated processes. These processes are strongly influenced by the readers'…

Data processing

CERN Document Server

Fry, T F

2013-01-01

Data Processing discusses the principles, practices, and associated tools in data processing. The book is comprised of 17 chapters that are organized into three parts. The first part covers the characteristics, systems, and methods of data processing. Part 2 deals with the data processing practice; this part discusses the data input, output, and storage. The last part discusses topics related to systems and software in data processing, which include checks and controls, computer language and programs, and program elements and structures. The text will be useful to practitioners of computer-rel

In-process and post-process measurements of drill wear for control of the drilling process

Science.gov (United States)

Liu, Tien-I.; Liu, George; Gao, Zhiyu

2011-12-01

Optical inspection was used in this research for the post-process measurements of drill wear. A precision toolmakers" microscope was used. Indirect index, cutting force, is used for in-process drill wear measurements. Using in-process measurements to estimate the drill wear for control purpose can decrease the operation cost and enhance the product quality and safety. The challenge is to correlate the in-process cutting force measurements with the post-process optical inspection of drill wear. To find the most important feature, the energy principle was used in this research. It is necessary to select only the cutting force feature which shows the highest sensitivity to drill wear. The best feature selected is the peak of torque in the drilling process. Neuro-fuzzy systems were used for correlation purposes. The Adaptive-Network-Based Fuzzy Inference System (ANFIS) can construct fuzzy rules with membership functions to generate an input-output pair. A 1x6 ANFIS architecture with product of sigmoid membership functions can in-process measure the drill wear with an error as low as 0.15%. This is extremely important for control of the drilling process. Furthermore, the measurement of drill wear was performed under different drilling conditions. This shows that ANFIS has the capability of generalization.

Quasi-Birth-and-Death Processes with Rational Arrival Process Components

DEFF Research Database (Denmark)

Bean, Nigel G.; Nielsen, Bo Friis

to develop an analytic method for such a process, that parallels the analysis of a traditional QBD. We demonstrate the analysis by considering a queue where the arrival process and the sequence of service times are derived from two different RAPs that are not just Markovian Arrival processes. We also...... introduce an element of correlation between the arrival process and the sequence of service times.......In this paper we introduce the concept of a Quasi-Birth-and-Death process (QBD) with Rational Arrival Process components. We use the physical interpretation of a Rational Arrival Process (RAP), developed by Asmussen and Bladt, to consider such a Markov process. We exploit this interpretation...

Processes subject to integrated pollution control. Petroleum processes: oil refining and associated processes

International Nuclear Information System (INIS)

1995-01-01

This document, part of a series offering guidance on pollution control regulations issued by Her Majesty's Inspectorate of Pollution, (HMIP) focuses on petroleum processes such as oil refining and other associated processes. The various industrial processes used, their associated pollution release routes into the environment and techniques for controlling these releases are all discussed. Environmental quality standards are related to national and international agreements on pollution control and abatement. HMIP's work on air, water and land pollution monitoring is also reported. (UK)

Reflow process stabilization by chemical characteristics and process conditions

Science.gov (United States)

Kim, Myoung-Soo; Park, Jeong-Hyun; Kim, Hak-Joon; Kim, Il-Hyung; Jeon, Jae-Ha; Gil, Myung-Goon; Kim, Bong-Ho

2002-07-01

With the shrunken device rule below 130nm, the patterning of smaller contact hole with enough process margin is required for mass production. Therefore, shrinking technology using thermal reflow process has been applied for smaller contact hole formation. In this paper, we have investigated the effects of chemical characteristics such as molecular weight, blocking ratio of resin, cross-linker amount and solvent type with its composition to reflow process of resist and found the optimized chemical composition for reflow process applicable condition. And several process conditions like resist coating thickness and multi-step thermal reflow method have been also evaluated to stabilize the pattern profile and improve CD uniformity after reflow process. From the experiment results, it was confirmed that the effect of crosslinker in resist to reflow properties such as reflow temperature and reflow rate were very critical and it controlled the pattern profile during reflow processing. And also, it showed stable CD uniformity and improved resist properties for top loss, film shrinkage and etch selectivity. The application of lower coating thickness of resist induced symmetric pattern profile even at edge with wider process margin. The introduction of two-step baking method for reflow process showed uniform CD value, also. It is believed that the application of resist containing crosslinker and optimized process conditions for smaller contact hole patterning is necessary for the mass production with a design rule below 130nm.

Microcrystalline silicon deposition: Process stability and process control

International Nuclear Information System (INIS)

Donker, M.N. van den; Kilper, T.; Grunsky, D.; Rech, B.; Houben, L.; Kessels, W.M.M.; Sanden, M.C.M. van de

2007-01-01

Applying in situ process diagnostics, we identified several process drifts occurring in the parallel plate plasma deposition of microcrystalline silicon (μc-Si:H). These process drifts are powder formation (visible from diminishing dc-bias and changing spatial emission profile on a time scale of 10 0 s), transient SiH 4 depletion (visible from a decreasing SiH emission intensity on a time scale of 10 2 s), plasma heating (visible from an increasing substrate temperature on a time scale of 10 3 s) and a still puzzling long-term drift (visible from a decreasing SiH emission intensity on a time scale of 10 4 s). The effect of these drifts on the crystalline volume fraction in the deposited films is investigated by selected area electron diffraction and depth-profiled Raman spectroscopy. An example shows how the transient depletion and long-term drift can be prevented by suitable process control. Solar cells deposited using this process control show enhanced performance. Options for process control of plasma heating and powder formation are discussed

The permanent process

DEFF Research Database (Denmark)

Møller, Jesper; McCullagh, Peter

We extend the boson process first to a large class of Cox processes and second an even larger class of infinitely divisible point processes. Density and moment results are studied in detail. These results are obtained in closed form as weighted permanents, so the extension is called a permanent...... process. Temporal extensions and a particularly tractable case of the permanent process are also studied. Extensions of the ferminon process along similar lines, leading to so-called determinant processes, are discussed at the end. While the permanent process is attractive, the determinant process...

Passive heat transfer enhancement in 3D corrugated tube

DEFF Research Database (Denmark)

Navickaité, Kristina; Engelbrecht, Kurt; Bahl, Christian

transfer and fluid flow with a constant wall temperature and total pressure drop. The governing equations for these problems were solved using the Finite Element Method. The results of numerical modelling show significant increase in NTU for double corrugated tubes compared to a circular tube. The friction......An innovative hydraulic design was studied for corrugated tube geometry for a heat exchanger. An ellipse based double corrugation was used as a concept of the geometry. The hydraulic diameter (Dh) is maintained over the tube length while the shape of the cross section varies continuously along...... the flow direction. 38 corrugated tubes with a Dh of 5 mm were studied numerically with corrugation heights from 0.23 to 0.69 mm and corrugation periods from 5 to 50 mm for laminar flow with water. Computational fluid dynamics (CFD) is used as a tool to study the effect of corrugation geometry on heat...

Temperature- and Turbidity-Dependent Competitive Interactions Between Invasive Freshwater Mussels.

Science.gov (United States)

Huang, Qihua; Wang, Hao; Ricciardi, Anthony; Lewis, Mark A

2016-03-01

We develop a staged-structured population model that describes the competitive dynamics of two functionally similar, congeneric invasive species: zebra mussels and quagga mussels. The model assumes that the population survival rates are functions of temperature and turbidity, and that the two species compete for food. The stability analysis of the model yields conditions on net reproductive rates and intrinsic growth rates that lead to competitive exclusion. The model predicts quagga mussel dominance leading to potential exclusion of zebra mussels at mean water temperatures below [Formula: see text] and over a broad range of turbidities, and a much narrower set of conditions that favor zebra mussel dominance and potential exclusion of quagga mussels at temperatures above [Formula: see text] and turbidities below 35 NTU. We then construct a two-patch dispersal model to examine how the dispersal rates and the environmental factors affect competitive exclusion and coexistence.

Study and economic analysis in the treatment of vinasse; Estudios y analisis economico en el tratamiento de vinazas

Energy Technology Data Exchange (ETDEWEB)

Lopez-Perez, L.; Perez-Baez, S. O.; Susial, P. [Universidad de Las Palmas de Gran Canarias (Spain)

2001-07-01

Different techniques to control and treatment wastewater from distillation alcohol plants are reviewed and a non conventional procedure in vinasses treatment obtained like stillage from fermented and distilled sugar cane juice is presented. Tests of coagulation-flocculation made with jar test equipment shows that a clear effluent verified by NTU is obtained, despite the rate of diminution of the DBO{sub 5} was smaller of 40%, reason why the designed technique needs to be combined with an oxidation pos treatment, after as the industrial wastewater satisfies the normative parameters. A comparative analysis of the coagulation-flocculation technique with respect to the conventional procedure anaerobic+aerobic treatment is made in economic terms. The obtained result shows that in small plants is viable a physical+chemical treatment, whenever the volume of vinasse to be treated must be smaller than 15 m''3/day. (Author) 30 refs.

Modelling and experimental validation for off-design performance of the helical heat exchanger with LMTD correction taken into account

Energy Technology Data Exchange (ETDEWEB)

Phu, Nguyen Minh; Trinh, Nguyen Thi Minh [Vietnam National University, Ho Chi Minh City (Viet Nam)

2016-07-15

Today the helical coil heat exchanger is being employed widely due to its dominant advantages. In this study, a mathematical model was established to predict off-design works of the helical heat exchanger. The model was based on the LMTD and e-NTU methods, where a LMTD correction factor was taken into account to increase accuracy. An experimental apparatus was set-up to validate the model. Results showed that errors of thermal duty, outlet hot fluid temperature, outlet cold fluid temperature, shell-side pressure drop, and tube-side pressure drop were respectively +-5%, +-1%, +-1%, +-5% and +-2%. Diagrams of dimensionless operating parameters and a regression function were also presented as design-maps, a fast calculator for usage in design and operation of the exchanger. The study is expected to be a good tool to estimate off-design conditions of the single-phase helical heat exchangers.

Data on microbiological quality assessment of rural drinking water supplies in Poldasht county.

Science.gov (United States)

Yousefi, Mahmood; Saleh, Hossein Najafi; Yaseri, Mehdi; Mahvi, Amir Hossein; Soleimani, Hamed; Saeedi, Zhyar; Zohdi, Sara; Mohammadi, Ali Akbar

2018-04-01

In this research, the villages with water supply systems under the supervision of the Water and Wastewater Company in Poldasht County, Iran in 2015 was studied. 648 samples were taken from 57 villages during 12month period to test for microbial quality according to the latest guidelines of WHO. Fecal coliform, coliform, turbidity, pH and free residual chlorine were analyzed. Also we used linear Regression statistical analysis for collected data. Result of Data showed that 13.6% of the villages under study had contaminated water resources. In 100 percent of the water sample resource the turbidity level was less than Iranian maximum permissible levels (5 NTU). There was a linear relation between the Free residual color and Coliform in different month of follow up ( r = -0.154, P water resources should be comprehensively planned and monitored keeping in view the WHO recommended parameters.

RELATIONSHIP BETWEEN THE EFFECTS OF INCREASING THE SATISFACTION OF THE VISITORS AND DEVELOPMENT OF CULTURAL TOURISM

Directory of Open Access Journals (Sweden)

Tünde SZABÓ

2011-12-01

Full Text Available In order to succeed on the market, organizations must permanently focus their efforts towards understanding and fulfilling the necessities and expectations of all their clients, both the current and the potential ones. At the same time, enterprises must identify methods and tools appropriate for evaluating the satisfaction degree of the clients and for ensuring the loyalty of the most important clients, as well as improving the internal and external relational system and creating new partnerships with loyal clients. The effects of increasing the client satisfaction can be numerous, and they depend greatly on the activities specific to each organization. In the current paper, an attempt is made to highlight the possible effects of increasing the satisfaction of the visitors of the National Seckler Museum from Sfîntu Gheorghe, - effects like an increased number of visitors, tourist attraction, developing and promoting cultural tourism in the county.

Multidimensional process discovery

NARCIS (Netherlands)

Ribeiro, J.T.S.

2013-01-01

Typically represented in event logs, business process data describe the execution of process events over time. Business process intelligence (BPI) techniques such as process mining can be applied to get strategic insight into business processes. Process discovery, conformance checking and

Process development

Energy Technology Data Exchange (ETDEWEB)

Schuegerl, K

1984-01-01

The item 'process development' comprises the production of acetonic/butonal with C. acetobylicum and the yeasting of potato waste. The target is to increase productivity by taking the following measures - optimation of media, on-line process analysis, analysis of reaction, mathematic modelling and identification of parameters, process simulation, development of a state estimator with the help of the on-line process analysis and the model, optimization and adaptive control.

Statistical Process Control for KSC Processing

Science.gov (United States)

Ford, Roger G.; Delgado, Hector; Tilley, Randy

1996-01-01

The 1996 Summer Faculty Fellowship Program and Kennedy Space Center (KSC) served as the basis for a research effort into statistical process control for KSC processing. The effort entailed several tasks and goals. The first was to develop a customized statistical process control (SPC) course for the Safety and Mission Assurance Trends Analysis Group. The actual teaching of this course took place over several weeks. In addition, an Internet version of the same course complete with animation and video excerpts from the course when it was taught at KSC was developed. The application of SPC to shuttle processing took up the rest of the summer research project. This effort entailed the evaluation of SPC use at KSC, both present and potential, due to the change in roles for NASA and the Single Flight Operations Contractor (SFOC). Individual consulting on SPC use was accomplished as well as an evaluation of SPC software for KSC use in the future. A final accomplishment of the orientation of the author to NASA changes, terminology, data format, and new NASA task definitions will allow future consultation when the needs arise.

A method for manufacturing a tool part for an injection molding process, a hot embossing process, a nano-imprint process, or an extrusion process

DEFF Research Database (Denmark)

2013-01-01

The present invention relates to a method for manufacturing a tool part for an injection molding process, a hot embossing process, nano-imprint process or an extrusion process. First, there is provided a master structure (10) with a surface area comprising nanometre-sized protrusions (11...

Process control using modern systems of information processing

International Nuclear Information System (INIS)

Baldeweg, F.

1984-01-01

Modern digital automation techniques allow the application of demanding types of process control. These types of process control are characterized by their belonging to higher levels in a multilevel model. Functional and technical aspects of the performance of digital automation plants are presented and explained. A modern automation system is described considering special procedures of process control (e.g. real time diagnosis)

Anaerobic treatment of wastewater from the household and personal products industry in a hybrid bioreactor

Directory of Open Access Journals (Sweden)

D. J. Araujo

2008-09-01

Full Text Available The anaerobic treatment of wastewater from the household and personal products industry was studied using a 16.3 L hybrid reactor (UASB and biofilter. The top of the UASB reactor was filled with coconut shells to act as the support material for the biofilter. The wastewater was characterized in terms of pH (1.0 - 12.0, COD (1,000 - 5,000 mg/L, BOD5 (700 - 1,500 mg/L, chloride (55 - 850 mg/L, ammonia nitrogen (0.4 - 0.9 mg/L, total Kjeldahl nitrogen (22.1 - 34.0 mg/L, phosphorus (2.0 - 2.5 mg/L, anionic surfactants (100 - 600 mg/L, turbidity (115 - 300 NTU and total suspended solids (450 - 1,440 mg/L. The bioreactor was operated continuously for 120 days at room temperature (26 ± 5ºC with hydraulic retention times of 50, 40 and 60 h. COD and BOD removals and biogas production were evaluated in order to analyze process efficiency. The average removal efficiencies for COD (77%, 72% and 80% and BOD5 (approximately 90% were obtained with HRTs of 50, 40 and 60 h, respectively. The average specific biogas production was 0.32 L/g COD (at standard temperature and pressure for the three experimental runs. These data indicate good reactor efficiency and suggest the possibility of using this system to treat wastewater generated by the household and personal products industry.

DUAL-PROCESS, a highly reliable process control system

International Nuclear Information System (INIS)

Buerger, L.; Gossanyi, A.; Parkanyi, T.; Szabo, G.; Vegh, E.

1983-02-01

A multiprocessor process control system is described. During its development the reliability was the most important aspect because it is used in the computerized control of a 5 MW research reactor. DUAL-PROCESS is fully compatible with the earlier single processor control system PROCESS-24K. The paper deals in detail with the communication, synchronization, error detection and error recovery problems of the operating system. (author)

Quasi-Birth-and-Death Processes with Rational Arrival Process Components

DEFF Research Database (Denmark)

Bean, Nigel G.; Nielsen, Bo Friis

2010-01-01

This paper introduces the concept of a Quasi-Birth-and-Death process (QBD) with Rational Arrival Process (RAP) components. We use the physical interpretation of the prediction process of the RAP, developed by Asmussen and Bladt, and develop an analysis that parallels the analysis of a traditional...... QBD. Further, we present an algorithm for the numerical evaluation of the matrix G. As an example, we consider two queues where the arrival process and the sequence of service times are taken from two dependent RAPs, that are not Markovian Arrival Processes......This paper introduces the concept of a Quasi-Birth-and-Death process (QBD) with Rational Arrival Process (RAP) components. We use the physical interpretation of the prediction process of the RAP, developed by Asmussen and Bladt, and develop an analysis that parallels the analysis of a traditional...

Stochastic processes

CERN Document Server

Parzen, Emanuel

1962-01-01

Well-written and accessible, this classic introduction to stochastic processes and related mathematics is appropriate for advanced undergraduate students of mathematics with a knowledge of calculus and continuous probability theory. The treatment offers examples of the wide variety of empirical phenomena for which stochastic processes provide mathematical models, and it develops the methods of probability model-building.Chapter 1 presents precise definitions of the notions of a random variable and a stochastic process and introduces the Wiener and Poisson processes. Subsequent chapters examine

Dosimetry and process control for radiation processing

International Nuclear Information System (INIS)

Mod Ali, N.

2002-01-01

Complete text of publication follows. Accurate radiation dosimetry can provide quality assurance in radiation processing. Considerable relevant experiences in dosimetry by the SSDL-MINT has necessitate the development of methods making measurement at gamma plant traceable to the national standard. It involves the establishment of proper calibration procedure and selection of appropriate transfer system/technique to assure adequate traceability to a primary radiation standard. The effort forms the basis for irradiation process control, the legal approval of the process by the public health authorities (medical product sterilization and food preservation) and the safety and acceptance of the product

Process mining using BPMN: relating event logs and process models

NARCIS (Netherlands)

Kalenkova, A.A.; van der Aalst, W.M.P.; Lomazova, I.A.; Rubin, V.A.

2017-01-01

Process-aware information systems (PAIS) are systems relying on processes, which involve human and software resources to achieve concrete goals. There is a need to develop approaches for modeling, analysis, improvement and monitoring processes within PAIS. These approaches include process mining

Process mining using BPMN : relating event logs and process models

NARCIS (Netherlands)

Kalenkova, A.A.; Aalst, van der W.M.P.; Lomazova, I.A.; Rubin, V.A.

2015-01-01

Process-aware information systems (PAIS) are systems relying on processes, which involve human and software resources to achieve concrete goals. There is a need to develop approaches for modeling, analysis, improvement and monitoring processes within PAIS. These approaches include process mining

Process modeling for Humanities: tracing and analyzing scientific processes

OpenAIRE

Hug , Charlotte; Salinesi , Camille; Deneckere , Rebecca; Lamasse , Stéphane

2011-01-01

International audience; This paper concerns epistemology and the understanding of research processes in Humanities, such as Archaeology. We believe that to properly understand research processes, it is essential to trace them. The collected traces depend on the process model established, which has to be as accurate as possible to exhaustively record the traces. In this paper, we briefly explain why the existing process models for Humanities are not sufficient to represent traces. We then pres...

Poisson processes

NARCIS (Netherlands)

Boxma, O.J.; Yechiali, U.; Ruggeri, F.; Kenett, R.S.; Faltin, F.W.

2007-01-01

The Poisson process is a stochastic counting process that arises naturally in a large variety of daily life situations. We present a few definitions of the Poisson process and discuss several properties as well as relations to some well-known probability distributions. We further briefly discuss the

Process improvement : the creation and evaluation of process alternatives

NARCIS (Netherlands)

Netjes, M.

2010-01-01

Companies continuously strive to improve their processes to increase productivity and delivered quality against lower costs. With Business Process Redesign (BPR) projects such improvement goals can be achieved. BPR involves the restructuring of business processes, stimulated by the application of

The permanental process

DEFF Research Database (Denmark)

McCullagh, Peter; Møller, Jesper

2006-01-01

We extend the boson process first to a large class of Cox processes and second to an even larger class of infinitely divisible point processes. Density and moment results are studied in detail. These results are obtained in closed form as weighted permanents, so the extension i called a permanental...... process. Temporal extensions and a particularly tractable case of the permanental process are also studied. Extensions of the fermion process along similar lines, leading to so-called determinantal processes, are discussed....

Dry process potentials

International Nuclear Information System (INIS)

Faugeras, P.

1997-01-01

Various dry processes have been studied and more or less developed in order particularly to reduce the waste quantities but none of them had replaced the PUREX process, for reasons departing to policy errors, un-appropriate demonstration examples or too late development, although realistic and efficient dry processes such as a fluoride selective volatility based processes have been demonstrated in France (CLOVIS, ATILA) and would be ten times cheaper than the PUREX process. Dry processes could regain interest in case of a nuclear revival (following global warming fears) or thermal wastes over-production. In the near future, dry processes could be introduced in complement to the PUREX process, especially at the end of the process cycle, for a more efficient recycling and safer storage (inactivation)

Business Process Customization using Process Merging Techniques

NARCIS (Netherlands)

Bulanov, Pavel; Lazovik, Alexander; Aiello, Marco

2012-01-01

One of the important application of service composition techniques lies in the field of business process management. Essentially a business process can be considered as a composition of services, which is usually prepared by domain experts, and many tasks still have to be performed manually. These

Business process transformation the process tangram framework

CERN Document Server

Sharma, Chitra

2015-01-01

This book presents a framework through transformation and explains  how business goals can be translated into realistic plans that are tangible and yield real results in terms of the top line and the bottom line. Process Transformation is like a tangram puzzle, which has multiple solutions yet is essentially composed of seven 'tans' that hold it together. Based on practical experience and intensive research into existing material, 'Process Tangram' is a simple yet powerful framework that proposes Process Transformation as a program. The seven 'tans' are: the transformation program itself, triggers, goals, tools and techniques, culture, communication and success factors. With its segregation into tans and division into core elements, this framework makes it possible to use 'pick and choose' to quickly and easily map an organization's specific requirements. Change management and process modeling are covered in detail. In addition, the book approaches managed services as a model of service delivery, which it ex...

Composable Data Processing in Environmental Science - A Process View

NARCIS (Netherlands)

Wombacher, Andreas

Data processing in environmental science is essential for doing science. The heterogeneity of data sources, data processing operations and infrastructures results in a lot of manual data and process integration work done by each scientist individually. This is very inefficient and time consuming.

Processing module operating methods, processing modules, and communications systems

Science.gov (United States)

McCown, Steven Harvey; Derr, Kurt W.; Moore, Troy

2014-09-09

A processing module operating method includes using a processing module physically connected to a wireless communications device, requesting that the wireless communications device retrieve encrypted code from a web site and receiving the encrypted code from the wireless communications device. The wireless communications device is unable to decrypt the encrypted code. The method further includes using the processing module, decrypting the encrypted code, executing the decrypted code, and preventing the wireless communications device from accessing the decrypted code. Another processing module operating method includes using a processing module physically connected to a host device, executing an application within the processing module, allowing the application to exchange user interaction data communicated using a user interface of the host device with the host device, and allowing the application to use the host device as a communications device for exchanging information with a remote device distinct from the host device.

Improving the process of process modelling by the use of domain process patterns

NARCIS (Netherlands)

Koschmider, A.; Reijers, H.A.

2015-01-01

The use of business process models has become prevalent in a wide area of enterprise applications. But while their popularity is expanding, concerns are growing with respect to their proper creation and maintenance. An obvious way to boost the efficiency of creating high-quality business process

Trends in business process analysis: from verification to process mining

NARCIS (Netherlands)

Aalst, van der W.M.P.; Cardoso, J.; Cordeiro, J.; Filipe, J.

2007-01-01

Business process analysis ranges from model verification at design-time to the monitoring of processes at runtime. Much progress has been achieved in process verification. Today we are able to verify the entire reference model of SAP without any problems. Moreover, more and more processes leave

Automatic extraction of process categories from process model collections

NARCIS (Netherlands)

Malinova, M.; Dijkman, R.M.; Mendling, J.; Lohmann, N.; Song, M.; Wohed, P.

2014-01-01

Many organizations build up their business process management activities in an incremental way. As a result, there is no overarching structure defined at the beginning. However, as business process modeling initiatives often yield hundreds to thousands of process models, there is a growing need for

Opportunities and challenges for process control in process intensification

NARCIS (Netherlands)

Nikacevic, N.M.; Huesman, A.E.M.; Hof, Van den P.M.J.; Stankiewicz, A.

2012-01-01

This is a review and position article discussing the role and prospective for process control in process intensification. Firstly, the article outlines the classical role of control in process systems, presenting an overview of control systems’ development, from basic PID control to the advanced

Transforming spatial point processes into Poisson processes using random superposition

DEFF Research Database (Denmark)

Møller, Jesper; Berthelsen, Kasper Klitgaaard

with a complementary spatial point process Y  to obtain a Poisson process X∪Y  with intensity function β. Underlying this is a bivariate spatial birth-death process (Xt,Yt) which converges towards the distribution of (X,Y). We study the joint distribution of X and Y, and their marginal and conditional distributions....... In particular, we introduce a fast and easy simulation procedure for Y conditional on X. This may be used for model checking: given a model for the Papangelou intensity of the original spatial point process, this model is used to generate the complementary process, and the resulting superposition is a Poisson...... process with intensity function β if and only if the true Papangelou intensity is used. Whether the superposition is actually such a Poisson process can easily be examined using well known results and fast simulation procedures for Poisson processes. We illustrate this approach to model checking...

Process/Equipment Co-Simulation on Syngas Chemical Looping Process

Energy Technology Data Exchange (ETDEWEB)

Zeng, Liang; Zhou, Qiang; Fan, Liang-Shih

2012-09-30

The chemical looping strategy for fossil energy applications promises to achieve an efficient energy conversion system for electricity, liquid fuels, hydrogen and/or chemicals generation, while economically separate CO{sub 2} by looping reaction design in the process. Chemical looping particle performance, looping reactor engineering, and process design and applications are the key drivers to the success of chemical looping process development. In order to better understand and further scale up the chemical looping process, issues such as cost, time, measurement, safety, and other uncertainties need to be examined. To address these uncertainties, advanced reaction/reactor modeling and process simulation are highly desired and the modeling efforts can accelerate the chemical looping technology development, reduce the pilot-scale facility design time and operating campaigns, as well as reduce the cost and technical risks. The purpose of this work is thus to conduct multiscale modeling and simulations on the key aspects of chemical looping technology, including particle reaction kinetics, reactor design and operation, and process synthesis and optimization.

Process Fragment Libraries for Easier and Faster Development of Process-based Applications

Directory of Open Access Journals (Sweden)

David Schumm

2011-01-01

Full Text Available The term “process fragment” is recently gaining momentum in business process management research. We understand a process fragment as a connected and reusable process structure, which has relaxed completeness and consistency criteria compared to executable processes. We claim that process fragments allow for an easier and faster development of process-based applications. As evidence to this claim we present a process fragment concept and show a sample collection of concrete, real-world process fragments. We present advanced application scenarios for using such fragments in development of process-based applications. Process fragments are typically managed in a repository, forming a process fragment library. On top of a process fragment library from previous work, we discuss the potential impact of using process fragment libraries in cross-enterprise collaboration and application integration.

Rapid thermal processing and beyond applications in semiconductor processing

CERN Document Server

Lerch, W

2008-01-01

Heat-treatment and thermal annealing are very common processing steps which have been employed during semiconductor manufacturing right from the beginning of integrated circuit technology. In order to minimize undesired diffusion, and other thermal budget-dependent effects, the trend has been to reduce the annealing time sharply by switching from standard furnace batch-processing (involving several hours or even days), to rapid thermal processing involving soaking times of just a few seconds. This transition from thermal equilibrium, to highly non-equilibrium, processing was very challenging a

Fractional Processes and Fractional-Order Signal Processing Techniques and Applications

CERN Document Server

Sheng, Hu; Qiu, TianShuang

2012-01-01

Fractional processes are widely found in science, technology and engineering systems. In Fractional Processes and Fractional-order Signal Processing, some complex random signals, characterized by the presence of a heavy-tailed distribution or non-negligible dependence between distant observations (local and long memory), are introduced and examined from the ‘fractional’ perspective using simulation, fractional-order modeling and filtering and realization of fractional-order systems. These fractional-order signal processing (FOSP) techniques are based on fractional calculus, the fractional Fourier transform and fractional lower-order moments. Fractional Processes and Fractional-order Signal Processing: • presents fractional processes of fixed, variable and distributed order studied as the output of fractional-order differential systems; • introduces FOSP techniques and the fractional signals and fractional systems point of view; • details real-world-application examples of FOSP techniques to demonstr...

Clinical Processes - The Killer Application for Constraint-Based Process Interactions

DEFF Research Database (Denmark)

Jiménez-Ramírez, Andrés; Barba, Irene; Reichert, Manfred

2018-01-01

. The scenario is subject to complex temporal constraints and entails the need for coordinating the constraint-based interactions among the processes related to a patient treatment process. As demonstrated in this work, the selected real process scenario can be suitably modeled through a declarative approach....... examples. However, to the best of our knowledge, they have not been used to model complex, real-world scenarios that comprise constraints going beyond control-flow. In this paper, we propose the use of a declarative language for modeling a sophisticated healthcare process scenario from the real world......For more than a decade, the interest in aligning information systems in a process-oriented way has been increasing. To enable operational support for business processes, the latter are usually specified in an imperative way. The resulting process models, however, tend to be too rigid to meet...

Process innovation laboratory

DEFF Research Database (Denmark)

Møller, Charles

2007-01-01

to create a new methodology for developing and exploring process models and applications. The paper outlines the process innovation laboratory as a new approach to BPI. The process innovation laboratory is a comprehensive framework and a collaborative workspace for experimenting with process models....... The process innovation laboratory facilitates innovation by using an integrated action learning approach to process modelling in a controlled environment. The study is based on design science and the paper also discusses the implications to EIS research and practice......Most organizations today are required not only to operate effective business processes but also to allow for changing business conditions at an increasing rate. Today nearly every business relies on their enterprise information systems (EIS) for process integration and future generations of EIS...

Membrane processes

Science.gov (United States)

Staszak, Katarzyna

2017-11-01

The membrane processes have played important role in the industrial separation process. These technologies can be found in all industrial areas such as food, beverages, metallurgy, pulp and paper, textile, pharmaceutical, automotive, biotechnology and chemical industry, as well as in water treatment for domestic and industrial application. Although these processes are known since twentieth century, there are still many studies that focus on the testing of new membranes' materials and determining of conditions for optimal selectivity, i. e. the optimum transmembrane pressure (TMP) or permeate flux to minimize fouling. Moreover the researchers proposed some calculation methods to predict the membrane processes properties. In this article, the laboratory scale experiments of membrane separation techniques, as well their validation by calculation methods are presented. Because membrane is the "heart" of the process, experimental and computational methods for its characterization are also described.

PROPOSAL OF SPATIAL OPTIMIZATION OF PRODUCTION PROCESS IN PROCESS DESIGNER

Directory of Open Access Journals (Sweden)

Peter Malega

2015-03-01

Full Text Available This contribution is focused on optimizing the use of space in the production process using software Process Designer. The aim of this contribution is to suggest possible improvements to the existing layout of the selected production process. Production process was analysed in terms of inputs, outputs and course of actions. Nowadays there are many software solutions aimed at optimizing the use of space. One of these software products is the Process Designer, which belongs to the product line Tecnomatix. This software is primarily aimed at production planning. With Process Designer is possible to design the layout of production and subsequently to analyse the production or to change according to the current needs of the company.

Process automation

International Nuclear Information System (INIS)

Moser, D.R.

1986-01-01

Process automation technology has been pursued in the chemical processing industries and to a very limited extent in nuclear fuel reprocessing. Its effective use has been restricted in the past by the lack of diverse and reliable process instrumentation and the unavailability of sophisticated software designed for process control. The Integrated Equipment Test (IET) facility was developed by the Consolidated Fuel Reprocessing Program (CFRP) in part to demonstrate new concepts for control of advanced nuclear fuel reprocessing plants. A demonstration of fuel reprocessing equipment automation using advanced instrumentation and a modern, microprocessor-based control system is nearing completion in the facility. This facility provides for the synergistic testing of all chemical process features of a prototypical fuel reprocessing plant that can be attained with unirradiated uranium-bearing feed materials. The unique equipment and mission of the IET facility make it an ideal test bed for automation studies. This effort will provide for the demonstration of the plant automation concept and for the development of techniques for similar applications in a full-scale plant. A set of preliminary recommendations for implementing process automation has been compiled. Some of these concepts are not generally recognized or accepted. The automation work now under way in the IET facility should be useful to others in helping avoid costly mistakes because of the underutilization or misapplication of process automation. 6 figs

Process Analytical Technology (PAT): batch-to-batch reproducibility of fermentation processes by robust process operational design and control.

Science.gov (United States)

Gnoth, S; Jenzsch, M; Simutis, R; Lübbert, A

2007-10-31

The Process Analytical Technology (PAT) initiative of the FDA is a reaction on the increasing discrepancy between current possibilities in process supervision and control of pharmaceutical production processes and its current application in industrial manufacturing processes. With rigid approval practices based on standard operational procedures, adaptations of production reactors towards the state of the art were more or less inhibited for long years. Now PAT paves the way for continuous process and product improvements through improved process supervision based on knowledge-based data analysis, "Quality-by-Design"-concepts, and, finally, through feedback control. Examples of up-to-date implementations of this concept are presented. They are taken from one key group of processes in recombinant pharmaceutical protein manufacturing, the cultivations of genetically modified Escherichia coli bacteria.

Defense Waste Processing Facility Process Simulation Package Life Cycle

International Nuclear Information System (INIS)

Reuter, K.

1991-01-01

The Defense Waste Processing Facility (DWPF) will be used to immobilize high level liquid radioactive waste into safe, stable, and manageable solid form. The complexity and classification of the facility requires that a performance based operator training to satisfy Department of Energy orders and guidelines. A major portion of the training program will be the application and utilization of Process Simulation Packages to assist in training the Control Room Operators on the fluctionality of the process and the application of the Distribution Control System (DCS) in operating and managing the DWPF process. The packages are being developed by the DWPF Computer and Information Systems Simulation Group. This paper will describe the DWPF Process Simulation Package Life Cycle. The areas of package scope, development, validation, and configuration management will be reviewed and discussed in detail

Comparative process mining in education : an approach based on process cubes

NARCIS (Netherlands)

van der Aalst, W.M.P.; Guo, S.; Gorissen, P.J.B.; Ceravolo, P.; Accorsi, R.; Cudre-Mauroux, P.

2015-01-01

Process mining techniques enable the analysis of a wide variety of processes using event data. For example, event logs can be used to automatically learn a process model (e.g., a Petri net or BPMN model). Next to the automated discovery of the real underlying process, there are process mining

Process mining

DEFF Research Database (Denmark)

van der Aalst, W.M.P.; Rubin, V.; Verbeek, H.M.W.

2010-01-01

Process mining includes the automated discovery of processes from event logs. Based on observed events (e.g., activities being executed or messages being exchanged) a process model is constructed. One of the essential problems in process mining is that one cannot assume to have seen all possible...... behavior. At best, one has seen a representative subset. Therefore, classical synthesis techniques are not suitable as they aim at finding a model that is able to exactly reproduce the log. Existing process mining techniques try to avoid such “overfitting” by generalizing the model to allow for more...... support for it). None of the existing techniques enables the user to control the balance between “overfitting” and “underfitting”. To address this, we propose a two-step approach. First, using a configurable approach, a transition system is constructed. Then, using the “theory of regions”, the model...

Process monitoring

International Nuclear Information System (INIS)

Anon.

1981-01-01

Many of the measurements and observations made in a nuclear processing facility to monitor processes and product quality can also be used to monitor the location and movements of nuclear materials. In this session information is presented on how to use process monitoring data to enhance nuclear material control and accounting (MC and A). It will be seen that SNM losses can generally be detected with greater sensitivity and timeliness and point of loss localized more closely than by conventional MC and A systems if process monitoring data are applied. The purpose of this session is to enable the participants to: (1) identify process unit operations that could improve control units for monitoring SNM losses; (2) choose key measurement points and formulate a loss indicator for each control unit; and (3) describe how the sensitivities and timeliness of loss detection could be determined for each loss indicator

Metacognition in Creativity: Process Awareness Used to Facilitate the Creative Process

DEFF Research Database (Denmark)

Valgeirsdóttir, Dagný; Onarheim, Balder

2017-01-01

to ensure capture of all instances of process awareness. Through this iterative process it was revealed that process awareness was predominantly observed in creativity related tasks. Moreover three distinct facets to process awareness emerged; planning, monitoring and reflecting, which were employed...... respectively before, during and after initiating a process and/or a workshop. We conclude that process awareness is an important creativity skill, being a crucial mechanism to enhance all stages of the creative process. If a designer becomes able to plan, monitor and reflect on his or her own cognitive...... processes, as well as other team members, he or she will be able to understand what works and what does not for advancing the creative process. In turn, that enables the designer to become more strategic about which actions are appropriate and at what time they are most usefully deployed; making the use...

Development of functionally-oriented technological processes of electroerosive processing

Science.gov (United States)

Syanov, S. Yu

2018-03-01

The stages of the development of functionally oriented technological processes of electroerosive processing from the separation of the surfaces of parts and their service functions to the determination of the parameters of the process of electric erosion, which will provide not only the quality parameters of the surface layer, but also the required operational properties, are described.

Data processing

International Nuclear Information System (INIS)

Cousot, P.

1988-01-01

The 1988 progress report of the Data Processing laboratory (Polytechnic School, France), is presented. The laboratory research fields are: the semantics, the tests and the semantic analysis of the codes, the formal calculus, the software applications, the algorithms, the neuron networks and VLSI (Very Large Scale Integration). The investigations concerning the polynomial rings are performed by means of the standard basis approach. Among the research topics, the Pascal codes, the parallel processing, the combinatorial, statistical and asymptotic properties of the fundamental data processing tools, the signal processing and the pattern recognition. The published papers, the congress communications and the thesis are also included [fr

PROCESS VARIABILITY REDUCTION THROUGH STATISTICAL PROCESS CONTROL FOR QUALITY IMPROVEMENT

Directory of Open Access Journals (Sweden)

B.P. Mahesh

2010-09-01

Full Text Available Quality has become one of the most important customer decision factors in the selection among the competing product and services. Consequently, understanding and improving quality is a key factor leading to business success, growth and an enhanced competitive position. Hence quality improvement program should be an integral part of the overall business strategy. According to TQM, the effective way to improve the Quality of the product or service is to improve the process used to build the product. Hence, TQM focuses on process, rather than results as the results are driven by the processes. Many techniques are available for quality improvement. Statistical Process Control (SPC is one such TQM technique which is widely accepted for analyzing quality problems and improving the performance of the production process. This article illustrates the step by step procedure adopted at a soap manufacturing company to improve the Quality by reducing process variability using Statistical Process Control.

Emotional Processing, Interaction Process, and Outcome in Clarification-Oriented Psychotherapy for Personality Disorders: A Process-Outcome Analysis.

Science.gov (United States)

Kramer, Ueli; Pascual-Leone, Antonio; Rohde, Kristina B; Sachse, Rainer

2016-06-01

It is important to understand the change processes involved in psychotherapies for patients with personality disorders (PDs). One patient process that promises to be useful in relation to the outcome of psychotherapy is emotional processing. In the present process-outcome analysis, we examine this question by using a sequential model of emotional processing and by additionally taking into account a therapist's appropriate responsiveness to a patient's presentation in clarification-oriented psychotherapy (COP), a humanistic-experiential form of therapy. The present study involved 39 patients with a range of PDs undergoing COP. Session 25 was assessed as part of the working phase of each therapy by external raters in terms of emotional processing using the Classification of Affective-Meaning States (CAMS) and in terms of the overall quality of therapist-patient interaction using the Process-Content-Relationship Scale (BIBS). Treatment outcome was assessed pre- and post-therapy using the Global Severity Index (GSI) of the SCL-90-R and the BDI. Results indicate that the good outcome cases showed more self-compassion, more rejecting anger, and a higher quality of therapist-patient interaction compared to poorer outcome cases. For good outcome cases, emotional processing predicted 18% of symptom change at the end of treatment, which was not found for poor outcome cases. These results are discussed within the framework of an integrative understanding of emotional processing as an underlying mechanism of change in COP, and perhaps in other effective therapy approaches for PDs.

Process Materialization Using Templates and Rules to Design Flexible Process Models

Science.gov (United States)

Kumar, Akhil; Yao, Wen

The main idea in this paper is to show how flexible processes can be designed by combining generic process templates and business rules. We instantiate a process by applying rules to specific case data, and running a materialization algorithm. The customized process instance is then executed in an existing workflow engine. We present an architecture and also give an algorithm for process materialization. The rules are written in a logic-based language like Prolog. Our focus is on capturing deeper process knowledge and achieving a holistic approach to robust process design that encompasses control flow, resources and data, as well as makes it easier to accommodate changes to business policy.

Thin film processes

CERN Document Server

Vossen, John L

1978-01-01

Remarkable advances have been made in recent years in the science and technology of thin film processes for deposition and etching. It is the purpose of this book to bring together tutorial reviews of selected filmdeposition and etching processes from a process viewpoint. Emphasis is placed on the practical use of the processes to provide working guidelines for their implementation, a guide to the literature, and an overview of each process.

Partial processing

International Nuclear Information System (INIS)

1978-11-01

This discussion paper considers the possibility of applying to the recycle of plutonium in thermal reactors a particular method of partial processing based on the PUREX process but named CIVEX to emphasise the differences. The CIVEX process is based primarily on the retention of short-lived fission products. The paper suggests: (1) the recycle of fission products with uranium and plutonium in thermal reactor fuel would be technically feasible; (2) it would, however, take ten years or more to develop the CIVEX process to the point where it could be launched on a commercial scale; (3) since the majority of spent fuel to be reprocessed this century will have been in storage for ten years or more, the recycling of short-lived fission products with the U-Pu would not provide an effective means of making refabrication fuel ''inaccessible'' because the radioactivity associated with the fission products would have decayed. There would therefore be no advantage in partial processing

Assessment of Process Capability: the case of Soft Drinks Processing Unit

Science.gov (United States)

Sri Yogi, Kottala

2018-03-01

The process capability studies have significant impact in investigating process variation which is important in achieving product quality characteristics. Its indices are to measure the inherent variability of a process and thus to improve the process performance radically. The main objective of this paper is to understand capability of the process being produced within specification of the soft drinks processing unit, a premier brands being marketed in India. A few selected critical parameters in soft drinks processing: concentration of gas volume, concentration of brix, torque of crock has been considered for this study. Assessed some relevant statistical parameters: short term capability, long term capability as a process capability indices perspective. For assessment we have used real time data of soft drinks bottling company which is located in state of Chhattisgarh, India. As our research output suggested reasons for variations in the process which is validated using ANOVA and also predicted Taguchi cost function, assessed also predicted waste monetarily this shall be used by organization for improving process parameters. This research work has substantially benefitted the organization in understanding the various variations of selected critical parameters for achieving zero rejection.

Perturbed GUE Minor Process and Warren's Process with Drifts

Science.gov (United States)

Ferrari, Patrik L.; Frings, René

2014-01-01

We consider the minor process of (Hermitian) matrix diffusions with constant diagonal drifts. At any given time, this process is determinantal and we provide an explicit expression for its correlation kernel. This is a measure on the Gelfand-Tsetlin pattern that also appears in a generalization of Warren's process (Electron. J. Probab. 12:573-590, 2007), in which Brownian motions have level-dependent drifts. Finally, we show that this process arises in a diffusion scaling limit from an interacting particle system in the anisotropic KPZ class in 2+1 dimensions introduced in Borodin and Ferrari (Commun. Math. Phys., 2008). Our results generalize the known results for the zero drift situation.

Integrated stationary Ornstein-Uhlenbeck process, and double integral processes

Science.gov (United States)

Abundo, Mario; Pirozzi, Enrica

2018-03-01

We find a representation of the integral of the stationary Ornstein-Uhlenbeck (ISOU) process in terms of Brownian motion Bt; moreover, we show that, under certain conditions on the functions f and g , the double integral process (DIP) D(t) = ∫βt g(s) (∫αs f(u) dBu) ds can be thought as the integral of a suitable Gauss-Markov process. Some theoretical and application details are given, among them we provide a simulation formula based on that representation by which sample paths, probability densities and first passage times of the ISOU process are obtained; the first-passage times of the DIP are also studied.

Integrating textual and model-based process descriptions for comprehensive process search

NARCIS (Netherlands)

Leopold, Henrik; van der Aa, Han; Pittke, Fabian; Raffel, Manuel; Mendling, Jan; Reijers, Hajo A.

2016-01-01

Documenting business processes using process models is common practice in many organizations. However, not all process information is best captured in process models. Hence, many organizations complement these models with textual descriptions that specify additional details. The problem with this

Neurological evidence linguistic processes precede perceptual simulation in conceptual processing.

Science.gov (United States)

Louwerse, Max; Hutchinson, Sterling

2012-01-01

There is increasing evidence from response time experiments that language statistics and perceptual simulations both play a role in conceptual processing. In an EEG experiment we compared neural activity in cortical regions commonly associated with linguistic processing and visual perceptual processing to determine to what extent symbolic and embodied accounts of cognition applied. Participants were asked to determine the semantic relationship of word pairs (e.g., sky - ground) or to determine their iconic relationship (i.e., if the presentation of the pair matched their expected physical relationship). A linguistic bias was found toward the semantic judgment task and a perceptual bias was found toward the iconicity judgment task. More importantly, conceptual processing involved activation in brain regions associated with both linguistic and perceptual processes. When comparing the relative activation of linguistic cortical regions with perceptual cortical regions, the effect sizes for linguistic cortical regions were larger than those for the perceptual cortical regions early in a trial with the reverse being true later in a trial. These results map upon findings from other experimental literature and provide further evidence that processing of concept words relies both on language statistics and on perceptual simulations, whereby linguistic processes precede perceptual simulation processes.

Silicon integrated circuit process

International Nuclear Information System (INIS)

Lee, Jong Duck

1985-12-01

This book introduces the process of silicon integrated circuit. It is composed of seven parts, which are oxidation process, diffusion process, ion implantation process such as ion implantation equipment, damage, annealing and influence on manufacture of integrated circuit and device, chemical vapor deposition process like silicon Epitaxy LPCVD and PECVD, photolithography process, including a sensitizer, spin, harden bake, reflection of light and problems related process, infrared light bake, wet-etch, dry etch, special etch and problems of etching, metal process like metal process like metal-silicon connection, aluminum process, credibility of aluminum and test process.

Silicon integrated circuit process

Energy Technology Data Exchange (ETDEWEB)

Lee, Jong Duck

1985-12-15

This book introduces the process of silicon integrated circuit. It is composed of seven parts, which are oxidation process, diffusion process, ion implantation process such as ion implantation equipment, damage, annealing and influence on manufacture of integrated circuit and device, chemical vapor deposition process like silicon Epitaxy LPCVD and PECVD, photolithography process, including a sensitizer, spin, harden bake, reflection of light and problems related process, infrared light bake, wet-etch, dry etch, special etch and problems of etching, metal process like metal process like metal-silicon connection, aluminum process, credibility of aluminum and test process.

Industrial processing versus home processing of tomato sauce

NARCIS (Netherlands)

Tomas, Merve; Beekwilder, Jules; Hall, Robert D.; Sagdic, Osman; Boyacioglu, Dilek; Capanoglu, Esra

2017-01-01

The effect of industrial and home processing, in vitro gastrointestinal digestion, individual phenolic content, and antioxidant capacity of tomato into tomato sauce were investigated. Industrial processing of tomato fruit into sauce had an overall positive effect on the total antioxidant capacity

Genetic process mining

NARCIS (Netherlands)

Aalst, van der W.M.P.; Alves De Medeiros, A.K.; Weijters, A.J.M.M.; Ciardo, G.; Darondeau, P.

2005-01-01

The topic of process mining has attracted the attention of both researchers and tool vendors in the Business Process Management (BPM) space. The goal of process mining is to discover process models from event logs, i.e., events logged by some information system are used to extract information about

Marshaling and Acquiring Resources for the Process Improvement Process

Science.gov (United States)

1993-06-01

stakeholders. ( Geber , 1990) D. IDENTIFYING SUPPLIERS Suppliers are just as crucial to setting requirements for processes as are customers. Although...output ( Geber , 1990, p. 32). Before gathering resources for process improvement, the functional manager must ensure that the relationship of internal...him patent information and clerical people process his applications. ( Geber , 1990, pp. 29-34) To get the full benefit of a white-collar worker as a

Process for recovering uranium from wet process phosphoric acid (III)

International Nuclear Information System (INIS)

Pyrih, R.Z.; Rickard, R.S.; Carrington, O.F.

1983-01-01

Uranium is conventionally recovered from wet-process phosphoric acid by two liquid ion exchange steps using a mixture of mono- and disubstituted phenyl esters of orthophosphoric acid (OPPA). Efficiency of the process drops as the mono-OPPA is lost preferentially to the aqueous phase. This invention provides a process for the removal of the uranium process organics (OPPA and organic solvents) from the raffinate of the first liquid ion exchange step and their return to the circuit. The process organics are removed by a combination flotation and absorption step, which results in the recovery of the organics on beads of a hydrophobic styrene polymer

Analytical method development and validation for quantification of uranium by Fourier Transform Infrared Spectroscopy (FTIR) for routine quality control analysis

International Nuclear Information System (INIS)

Pereira, Elaine; Silva, Ieda de S.; Gomide, Ricardo G.; Pires, Maria Aparecida F.

2015-01-01

This work presents a low cost, simple and new methodology for direct determination uranium in different matrices uranium: organic phase (UO 2 (NO 3 ) 2 .2TBP - uranyl nitrate complex) and aqueous phase (UO 2 (NO 3 ) 2 - NTU - uranyl nitrate), based on Fourier Transform Infrared spectroscopy (FTIR) using KBr pellets technique. The analytical validation is essential to define if a developed methodology is completely adjusted to the objectives that it is destined and is considered one of the main instruments of quality control. The parameters used in the validation process were: selectivity, linearity, limits of detection (LD) and quantitation (LQ), precision (repeatability and intermediate precision), accuracy and robustness. The method for uranium in organic phase (UO 2 (NO 3 ) 2 .2TBP in hexane/embedded in KBr) was linear (r=0.9989) over the range of 1.0 g L -1 a 14.3 g L -1 , LD were 92.1 mg L -1 and LQ 113.1 mg L -1 , precision (RSD < 1.6% and p-value < 0.05), accurate (recovery of 100.1% - 102.9%). The method for uranium aqueous phase (UO 2 (NO 3 )2/embedded in KBr) was linear (r=0.9964) over the range of 5.4 g L -1 a 51.2 g L -1 , LD were 835 mg L -1 and LQ 958 mg L -1 , precision (RSD < 1.0% and p-value < 0.05), accurate (recovery of 99.1% - 102.0%). The FTIR method is robust regarding most of the variables analyzed, as the difference between results obtained under nominal and modified conditions were lower than the critical value for all analytical parameters studied. Some process samples were analyzed in FTIR and compared with gravimetric and x ray fluorescence (XRF) analyses showing similar results in all three methods. The statistical tests (Student-t and Fischer) showed that the techniques are equivalent. (author)

Mineralizing urban net-zero water treatment: Field experience for energy-positive water management.

Science.gov (United States)

Wu, Tingting; Englehardt, James D

2016-12-01

An urban net-zero water treatment system, designed for energy-positive water management, 100% recycle of comingled black/grey water to drinking water standards, and mineralization of hormones and other organics, without production of concentrate, was constructed and operated for two years, serving an occupied four-bedroom, four-bath university residence hall apartment. The system comprised septic tank, denitrifying membrane bioreactor (MBR), iron-mediated aeration (IMA) reactor, vacuum ultrafilter, and peroxone or UV/H 2 O 2 advanced oxidation, with 14% rainwater make-up and concomitant discharge of 14% of treated water (ultimately for reuse in irrigation). Chemical oxygen demand was reduced to 12.9 ± 3.7 mg/L by MBR and further decreased to below the detection limit (treatment. The process produced a mineral water meeting 115 of 115 Florida drinking water standards that, after 10 months of recycle operation with ∼14% rainwater make-up, had a total dissolved solids of ∼500 mg/L, pH 7.8 ± 0.4, turbidity 0.12 ± 0.06 NTU, and NO 3 -N concentration 3.0 ± 1.0 mg/L. None of 97 hormones, personal care products, and pharmaceuticals analyzed were detected in the product water. For a typical single-home system with full occupancy, sludge pumping is projected on a 12-24 month cycle. Operational aspects, including disinfection requirements, pH evolution through the process, mineral control, advanced oxidation by-products, and applicability of point-of-use filters, are discussed. A distributed, peroxone-based NZW management system is projected to save more energy than is consumed in treatment, due largely to retention of wastewater thermal energy. Recommendations regarding design and operation are offered. Copyright © 2016 Elsevier Ltd. All rights reserved.

Oily wastewater treatment at Khartoum North Power Station

International Nuclear Information System (INIS)

Eltahir, M. M.; Taha, T. S.

2009-01-01

To a chief these goals a series of experimental procedure have been executed for the wastewater in sump tank at river side where all wastewater collected. This paper attempts to investigate the chemical and physical characteristics of Khartoum North Power Station waste water and to suggest methods for removing oil before being discharged to River Bule Nile. To achieve this goal numerous numbers of samples have been collected and examined to detect oil content, turbidity, suspended solids, total dissolved solids, pH, BOD, COD and conductivity, and average values of these parameters were 924.3 ppm, 554.2 NTU, 80 ppm, 559.5 ppm, 7.3 pH unit, 130 Pm, 443.14 ppm, 736.7 μs/cm respectively. The average values of these results were compared with [1] guide lines which are 15 ppm, 5 ppm, 60 ppm, <1000 ppm, 7.5 pH unit, 60 ppm, 100 ppm 500 μs/cm respectively. The outcome of the paper confirmed that waste water at Khartoum North Power Station (KNPS) is heavily polluted with oil and other pollutants. For this reason a second phase of experiments is carried out mainly to remove or reduce oil content to 6.7 ppm and other pollutants to levels which may comply with International Regulations and Local Authority acts. The treatment phase of experiment comprising different processing units arranged in a logical sequence starting with units for oil removal through a coagulation process, NaoH ending with air floatation and skimping to reduce oil content. Results obtained from second phase of experiments after waste water being treated are encouraging and a total reduction in contamination of not less than 80% has been achieved. (Author)

Extensible packet processing architecture

Science.gov (United States)

Robertson, Perry J.; Hamlet, Jason R.; Pierson, Lyndon G.; Olsberg, Ronald R.; Chun, Guy D.

2013-08-20

A technique for distributed packet processing includes sequentially passing packets associated with packet flows between a plurality of processing engines along a flow through data bus linking the plurality of processing engines in series. At least one packet within a given packet flow is marked by a given processing engine to signify by the given processing engine to the other processing engines that the given processing engine has claimed the given packet flow for processing. A processing function is applied to each of the packet flows within the processing engines and the processed packets are output on a time-shared, arbitered data bus coupled to the plurality of processing engines.

Process intensification on membrane-based process for blackcurrant juice concentration

DEFF Research Database (Denmark)

Fjerbæk Søtoft, Lene; Rong, Ben-Guang; Christensen, Knud Villy

Juice concentrate production is a field where process intensification and novel concentration processes need to be implemented. The paper presents a systematic approach for process synthesis based on membrane processes for the concentration of blackcurrant juice, exemplified by the aroma recovery...... using combinations of vacuum membrane distillation and traditional distillation. Furthermore, the paper further suggests a novel method for the combination of nanofiltration, reverse osmosis and membrane distillation for the concentration of the dearomatized juice....

Application of various technological processes in red clover seed processing

OpenAIRE

Đokić, Dragoslav; Stanisavljević, Rade; Terzić, Dragan; Marković, Jordan; Radivojević, Gordana; Anđelković, Bojan; Barać, Saša

2012-01-01

This paper presents the results of the processing of natural red clover seed on the processing equipment using different technological methods. Red clover seed, for the establishment and crop utilization, must be of high purity, germination, and high genetic values. These requirements are achieved by processing, or removing impurities and poor quality seeds. Red clover seed processing involves a number of operations, of which the most important are: cleaning, packaging, labeling and storage. ...

CO-PRODUCT ENHANCEMENT AND DEVELOPMENT FOR THE MASADA OXYNOL PROCESS PROCESS

Energy Technology Data Exchange (ETDEWEB)

Donald V. Watkins

2010-06-14

The focus of this project was an overall process improvement through the enhancement of the co-product streams. The enhancement of the process operations and co-products will increase both ethanol production and the value of other process outputs and reduces the amount of waste byproducts. This leads to a more economical and environmentally sound alternative to landfill disposal of municipal solid waste (MSW). These enhancements can greatly increase the commercial potential for the production of ethanol from MSW by the Masada CES OxyNol process. Both technological and economical issues were considered for steps throughout the conversion process. The research efforts of this project are varied but synergistic. The project investigated many of the operations involved in the Masada process with the overall goal of process improvements. The general goal of the testing was to improve co-product quality, improve conversions efficiencies, minimize process losses, increase energy efficiency, and mitigate process and commercialization risks. The project was divided into 16 subtasks as described in general terms below. All these tasks are interrelated but not necessarily interdependent.

Modeling the Object-Oriented Software Process: OPEN and the Unified Process

NARCIS (Netherlands)

van den Berg, Klaas; Aksit, Mehmet; van den Broek, P.M.

A short introduction to software process modeling is presented, particularly object-oriented modeling. Two major industrial process models are discussed: the OPEN model and the Unified Process model. In more detail, the quality assurance in the Unified Process tool (formally called Objectory) is

Links between attachment and social information processing: examination of intergenerational processes.

Science.gov (United States)

Dykas, Matthew J; Ehrlich, Katherine B; Cassidy, Jude

2011-01-01

This chapter describes theory and research on intergenerational connections between parents' attachment and children's social information processing, as well as between parents' social information processing and children's attachment. The chapter begins with a discussion of attachment theorists' early insights into the role that social information processing plays in attachment processes. Next, current theory about the mechanisms through which cross-generational links between attachment and social information processing might emerge is presented. The central proposition is that the quality of attachment and/or the social information processing of the parent contributes to the quality of attachment and/or social information processing in the child, and these links emerge through mediating processes related to social learning, open communication, gate-keeping, emotion regulation, and joint attention. A comprehensive review of the literature is then presented. The chapter ends with the presentation of a current theoretical perspective and suggestions for future empirical and clinical endeavors.

Comparisons of benthic filter feeder communities before and after a large-scale capital dredging program.

Science.gov (United States)

Abdul Wahab, Muhammad Azmi; Fromont, Jane; Gomez, Oliver; Fisher, Rebecca; Jones, Ross

2017-09-15

Changes in turbidity, sedimentation and light over a two year large scale capital dredging program at Onslow, northwestern Australia, were quantified to assess their effects on filter feeder communities, in particular sponges. Community functional morphological composition was quantified using towed video surveys, while dive surveys allowed for assessments of species composition and chlorophyll content. Onslow is relatively diverse recording 150 sponge species. The area was naturally turbid (1.1 mean P 80 NTU), with inshore sites recording 6.5× higher turbidity than offshore localities, likely influenced by the Ashburton River discharge. Turbidity and sedimentation increased by up to 146% and 240% through dredging respectively, with corresponding decreases in light levels. The effects of dredging was variable, and despite existing caveats (i.e. bleaching event and passing of a cyclone), the persistence of sponges and the absence of a pronounced response post-dredging suggest environmental filtering or passive adaptation acquired pre-dredging may have benefited these communities. Copyright © 2017. Published by Elsevier Ltd.

2nd Workshop on the Chemistry of Energy Conversion

CERN Document Server

2016-01-01

A sustainable energy future that does not rely on fossil fuels requires the advances of new materials design and development with efficient energy conversion. However, materials development is still at its infancy. There is an imperative to develop new energy conversion strategies. In Nature, plants harness sunlight and convert them into chemical energy. The ability to mimic Nature by combining synthetic nanoscopic and molecular components to produce chemical fuels is the Holy Grail to achieve sustainable energy production.​ The Institute of Advanced Studies (IAS) and the School of Physical and Mathematical Sciences (SPMS), NTU, are jointly organizing this workshop. We aim to create dialogues among scientists in the energy conversion field, with the ultimate goal of facilitating breakthroughs in materials design for energy conversion. It will also bring the expertise on Chemistry of Energy Conversion to the door steps of the materials research community in Singapore and also provide a platform for partic...

Heat pipe heat exchanger and its potential to energy recovery in the tropics

Directory of Open Access Journals (Sweden)

Yau Yat H.

2015-01-01

Full Text Available The heat recovery by the heat pipe heat exchangers was studied in the tropics. Heat pipe heat exchangers with two, four, six, and eight numbers of rows were examined for this purpose. The coil face velocity was set at 2 m/s and the temperature of return air was kept at 24°C in this study. The performance of the heat pipe heat exchangers was recorded during the one week of operation (168 hours to examine the performance data. Then, the collected data from the one week of operation were used to estimate the amount of energy recovered by the heat pipe heat exchangers annually. The effect of the inside design temperature and the coil face velocity on the energy recovery for a typical heat pipe heat exchanger was also investigated. In addition, heat pipe heat exchangers were simulated based on the effectiveness-NTU method, and their theoretical values for the thermal performance were compared with the experimental results.

Studi Variasi Beab Pendinginan pada Evaporator pada Low Stage Sistem Refrigerasi Cascade R22-404A

Directory of Open Access Journals (Sweden)

Moch. Munirul Ichsan

2013-03-01

Full Text Available Saat ini banyak dibutuhkan sistem pendingingan yang memiliki temperatur rendah dan kapasitas yang besar. Maka dari itu digunakanlah sistem refrigerasi cascade yang disusun atas dua stage yaitu high stage dan low stage. Alat pengujian sistem refrigerasi cascade ini menggunakan refrigerant R-22 di high stage dan R-404A di low stage yang dihubungkan dengan heat exchanger tipe konsentrik untuk memindahkan kalor dari kondensor low stage menuju evaporator high stage. Dalam melakukan pengujian diberikan beban pendinginan sebanyak sepuluh variasi heater. Dengan variasi beban mulai dari tanpa pemberian beban sampai beban heater sebesar 203,72watt. Sehingga setelah melakukan penelitian ini didapatkan hasil yang optimum pada pembebanan 203,72watt berupa COPcascade 1,06213, εeffectiveness 0,78313, temperatur evaporator minimum -26,9 °C. Dan dari hasil ini menunjukkan desain heat exchanger tipe konsentrik sangat menentukan dalam perpindahan panas, sehingga performa dari sistem refrigerasi cascade sangat ditentukan oleh tingkat perpindahan kalor pada heat exchanger yang diketahui melalui nilai εeffectiveness dan NTU.

A simplified modeling of mechanical cooling tower for control and optimization of HVAC systems

International Nuclear Information System (INIS)

Jin, Guang-Yu; Cai, Wen-Jian; Lu Lu; Lee, Eng Lock; Chiang, Andrew

2007-01-01

This paper proposes a new, simple, yet accurate mechanical cooling tower model for the purpose of energy conservation and management. On the basis of Merkel's theory and effectiveness-NTU method, the model is developed by energy balance and heat, mass transfer analysis. Commissioning information is then used to identified, only three model parameters by Levenberg-Marquardt method. Compared with the existing models, the proposed model has simple characteristic parameters to be determined and without requiring iterative computation when the operating point changes. The model is validated by real operating data from the cooling towers of a heating, ventilating and air conditioning (HVAC) system of a commercial hotel. The testing results show that the performance of the cooling tower varies from time to time due to different operating conditions and the proposed model is able to reflect these changes by tuning its parameters. With this feature, the proposed model can be simply used and accurately predict the performance of the real-time operating cooling tower

Treatment of water turbidity and bacteria by using a coagulant extracted from Plantago ovata

Directory of Open Access Journals (Sweden)

Bahman Ramavandi

2014-08-01

Full Text Available A biocoagulant was successfully extracted from Plantago ovata by using an FeCl3-induced crude extract (FCE. The potential of FCE to act as a natural coagulant was tested for clarification using the turbid water of a river. Experimental tests were performed to evaluate the effects of turbidity concentration, coagulant quantity, water pH, and humic acid concentration on the coagulation of water turbidity by FCE. The maximum turbidity removal was occurred at water pH<8. At the optimum dosage of FCE, only 0.8 mg/L of dissolved organic carbon was released to the treated water. An increase in the humic acid led to the promotion of the water turbidity removal. Results demonstrated that the FCE removed more than 95.6% of all initial turbidity concentrations (50–300 NTU. High bacteriological quality was achieved in the treated water. FCE as an eco-friendly biocoagulant was revealed to be a very efficient coagulant for removing turbidity from waters.

DISCRIMINANT ANALYSIS IN MARKETING RESEARCH

Directory of Open Access Journals (Sweden)

Erika KULCSÁR

2010-01-01

Full Text Available This paper classifies among marketing researches aiming to study the influence that the following independent variables (explanatory have: "Estimating the expenses incurred in Centre Development Region, including country of residence" and the variable "How many days have you planned to stay in this region?" on the construction of separate groups which form the dependent variables - the type of tourist (foreign, Romanian. Thus I shall analyse the explication of the different characteristics of the groups in terms of different attributes that members of these groups have with respect to the independent variables (explanatory. Questionnaires have been distributed to hotels in Braşov, Predeal, Poiana-Braşov, Sfântu Gheorghe, Covasna, Miercurea-Ciuc, Gheorgheni, Tuşnad, Târgu-Mureş, Sighişoara, Sibiu, Alba – Iulia and other localities that have linked this route. More than 2,000 questionnaires have been distributed. The quantitative research was conducted between 15.05.2009-17.10.2009.

Immunomodulatory activities and antioxidant properties of polysaccharides from Monascus-fermented products in vitro.

Science.gov (United States)

Tseng, Kuo-Chuan; Fang, Tony J; Chiang, Shen-Shih; Liu, Chin-Feng; Wu, Cheng-Lun; Pan, Tzu-Ming

2012-05-01

Monascus-fermented products have featured in Chinese cuisine for thousands of years and are widely used as food colourants and dietary materials in many Asian countries. Rice and dioscorea fermented with Monascus purpureus NTU 568 have health-promoting attributes in vitro and in vivo. The aim of this study was to investigate the immunomodulatory and antioxidant effects of polysaccharides from red mould rice (RMRP) and red mould dioscorea (RMDP) in Raw 264.7 cells. The results showed the antioxidant capabilities (including scavenging, chelating, inhibition of lipid peroxidation, and reducing power) of RMRP and RMDP at a concentration of 10 mg mL(-1). RMRP and RMDP also stimulated cell proliferation, nitric oxide production, phagocytosis and cytokine production (including IL1-β, IL-6 and TNF-α) in Raw 264.7 cells. These findings demonstrate that RMRP and RMDP have antioxidant and immunomodulation potential to be developed as novel dietary supplements. Copyright © 2011 Society of Chemical Industry.

Development of a control system for shell and tube heat exchanger in Matlab simulink

International Nuclear Information System (INIS)

Zeeshan, H.M.

2014-01-01

The main objective of this research is to develop a control system for heat exchanger so that the desired outlet temperature can be achieved by controlling the flow rate. For this purpose, shell and tube heat exchanger was chosen and modeled it by using its mathematical equations in MATLAB (Matrix Laboratory) Simulink and calculated the outlet temperature by NTU (Number of Transfer Units) effectiveness method. For the purpose of Control system, MPC (Model Predictive Controller) was used. This research will open a new way of Modeling Equations instead of transfer functions in MATLAB (Matrix Laboratory) Simulink. Using the model, it was developed; with controller, so as to manipulate the output temperature by simply controlling the flow rate. It can be justified weather the design of a new heat exchanger would be feasible or not for the specific requirements. At last this research is very helpful in Industries for the purpose of designing, development and control of new Heat Exchangers. (author)

Parametric studies on automotive radiators

International Nuclear Information System (INIS)

Oliet, C.; Oliva, A.; Castro, J.; Perez-Segarra, C.D.

2007-01-01

This paper presents a set of parametric studies performed on automotive radiators by means of a detailed rating and design heat exchanger model developed by the authors. This numerical tool has been previously verified and validated using a wide experimental data bank. A first part of the analysis focuses on the influence of working conditions on both fluids (mass flows, inlet temperatures) and the impact of the selected coolant fluid. Following these studies, the influence of some geometrical parameters is analysed (fin pitch, louver angle) as well as the importance of coolant flow lay-out on the radiator global performance. This work provides an overall behaviour report of automobile radiators working at usual range of operating conditions, while significant knowledge-based design conclusions have also been reported. The results show the utility of this numerical model as a rating and design tool for heat exchangers manufacturers, being a reasonable compromise between classic ε - NTU methods and CFD

A Repeatable Collaboration Process for Exploring Business Process Improvement Alternatives

NARCIS (Netherlands)

Sol, H G; Amiyo, Mercy; Nabukenya, J.

2012-01-01

The dynamic nature of organisations has increased demand for business process agility leading to the adoption of continuous Business Process Improvement (BPI). Success of BPI projects calls for continuous process analysis and exploration of several improvement alternatives. These activities are

Processing approaches to cognition: the impetus from the levels-of-processing framework.

Science.gov (United States)

Roediger, Henry L; Gallo, David A; Geraci, Lisa

2002-01-01

Processing approaches to cognition have a long history, from act psychology to the present, but perhaps their greatest boost was given by the success and dominance of the levels-of-processing framework. We review the history of processing approaches, and explore the influence of the levels-of-processing approach, the procedural approach advocated by Paul Kolers, and the transfer-appropriate processing framework. Processing approaches emphasise the procedures of mind and the idea that memory storage can be usefully conceptualised as residing in the same neural units that originally processed information at the time of encoding. Processing approaches emphasise the unity and interrelatedness of cognitive processes and maintain that they can be dissected into separate faculties only by neglecting the richness of mental life. We end by pointing to future directions for processing approaches.

Editorial: "Business process intelligence : connecting data and processes"

NARCIS (Netherlands)

Aalst, van der W.M.P.; Zhao, J.L.; Wang, H.; Wang, Harry Jiannan

2015-01-01

This introduction to the special issue on Business Process Intelligence (BPI) discusses the relation between data and processes. The recent attention for Big Data illustrates that organizations are aware of the potential of the torrents of data generated by today's information systems. However, at

Modeling the Object-Oriented Software Process: OPEN and the Unified Process

OpenAIRE

van den Berg, Klaas; Aksit, Mehmet; van den Broek, P.M.

1999-01-01

A short introduction to software process modeling is presented, particularly object-oriented modeling. Two major industrial process models are discussed: the OPEN model and the Unified Process model. In more detail, the quality assurance in the Unified Process tool (formally called Objectory) is reviewed.

Process modelling on a canonical basis[Process modelling; Canonical modelling

Energy Technology Data Exchange (ETDEWEB)

Siepmann, Volker

2006-12-20

Based on an equation oriented solving strategy, this thesis investigates a new approach to process modelling. Homogeneous thermodynamic state functions represent consistent mathematical models of thermodynamic properties. Such state functions of solely extensive canonical state variables are the basis of this work, as they are natural objective functions in optimisation nodes to calculate thermodynamic equilibrium regarding phase-interaction and chemical reactions. Analytical state function derivatives are utilised within the solution process as well as interpreted as physical properties. By this approach, only a limited range of imaginable process constraints are considered, namely linear balance equations of state variables. A second-order update of source contributions to these balance equations is obtained by an additional constitutive equation system. These equations are general dependent on state variables and first-order sensitivities, and cover therefore practically all potential process constraints. Symbolic computation technology efficiently provides sparsity and derivative information of active equations to avoid performance problems regarding robustness and computational effort. A benefit of detaching the constitutive equation system is that the structure of the main equation system remains unaffected by these constraints, and a priori information allows to implement an efficient solving strategy and a concise error diagnosis. A tailor-made linear algebra library handles the sparse recursive block structures efficiently. The optimisation principle for single modules of thermodynamic equilibrium is extended to host entire process models. State variables of different modules interact through balance equations, representing material flows from one module to the other. To account for reusability and encapsulation of process module details, modular process modelling is supported by a recursive module structure. The second-order solving algorithm makes it

Uranium enrichment. Enrichment processes

International Nuclear Information System (INIS)

Alexandre, M.; Quaegebeur, J.P.

2009-01-01

Despite the remarkable progresses made in the diversity and the efficiency of the different uranium enrichment processes, only two industrial processes remain today which satisfy all of enriched uranium needs: the gaseous diffusion and the centrifugation. This article describes both processes and some others still at the demonstration or at the laboratory stage of development: 1 - general considerations; 2 - gaseous diffusion: physical principles, implementation, utilisation in the world; 3 - centrifugation: principles, elementary separation factor, flows inside a centrifuge, modeling of separation efficiencies, mechanical design, types of industrial centrifuges, realisation of cascades, main characteristics of the centrifugation process; 4 - aerodynamic processes: vortex process, nozzle process; 5 - chemical exchange separation processes: Japanese ASAHI process, French CHEMEX process; 6 - laser-based processes: SILVA process, SILMO process; 7 - electromagnetic and ionic processes: mass spectrometer and calutron, ion cyclotron resonance, rotating plasmas; 8 - thermal diffusion; 9 - conclusion. (J.S.)

Science-based information processing in the process control of power stations

International Nuclear Information System (INIS)

Weisang, C.

1992-01-01

Through the application of specialized systems, future-orientated information processing integrates the sciences of processes, control systems, process control strategies, user behaviour and ergonomics. Improvements in process control can be attained, inter alia, by the preparation of the information contained (e.g. by suppressing the flow of signals and replacing it with signals which are found on substance) and also by an ergonomic representation of the study of the process. (orig.) [de

Process mining: discovering direct successors in process logs

NARCIS (Netherlands)

Maruster, L.; Weijters, A.J.M.M.; Aalst, van der W.M.P.; Bosch, van den A.P.J.; Lange, S.; Satoh, K.; Smith, C.H.

2002-01-01

Workflow management technology requires the existence of explicit process models, i.e. a completely specified workflow design needs to be developed in order to enact a given workflow process. Such a workflow design is time consuming and often subjective and incomplete. We propose a learning method

Internal process: what is abstraction and distortion process?

Science.gov (United States)

Fiantika, F. R.; Budayasa, I. K.; Lukito, A.

2018-03-01

Geometry is one of the branch of mathematics that plays a major role in the development of science and technology. Thus, knowing the geometry concept is needed for students from their early basic level of thinking. A preliminary study showed that the elementary students have difficulty in perceiving parallelogram shape in a 2-dimention of a cube drawing as a square shape. This difficulty makes the students can not solve geometrical problems correctly. This problem is related to the internal thinking process in geometry. We conducted the exploration of students’ internal thinking processes in geometry particularly in distinguishing the square and parallelogram shape. How the students process their internal thinking through distortion and abstraction is the main aim of this study. Analysis of the geometrical test and deep interview are used in this study to obtain the data. The result of this study is there are two types of distortion and abstraction respectively in which the student used in their internal thinking processes.

Nonaqueous processing methods

International Nuclear Information System (INIS)

Coops, M.S.; Bowersox, D.F.

1984-09-01

A high-temperature process utilizing molten salt extraction from molten metal alloys has been developed for purification of spent power reactor fuels. Experiments with laboratory-scale processing operations show that purification and throughput parameters comparable to the Barnwell Purex process can be achieved by pyrochemical processing in equipment one-tenth the size, with all wastes being discharged as stable metal alloys at greatly reduced volume and disposal cost. This basic technology can be developed for large-scale processing of spent reactor fuels. 13 references, 4 figures

Transforming Collaborative Process Models into Interface Process Models by Applying an MDA Approach

Science.gov (United States)

Lazarte, Ivanna M.; Chiotti, Omar; Villarreal, Pablo D.

Collaborative business models among enterprises require defining collaborative business processes. Enterprises implement B2B collaborations to execute these processes. In B2B collaborations the integration and interoperability of processes and systems of the enterprises are required to support the execution of collaborative processes. From a collaborative process model, which describes the global view of the enterprise interactions, each enterprise must define the interface process that represents the role it performs in the collaborative process in order to implement the process in a Business Process Management System. Hence, in this work we propose a method for the automatic generation of the interface process model of each enterprise from a collaborative process model. This method is based on a Model-Driven Architecture to transform collaborative process models into interface process models. By applying this method, interface processes are guaranteed to be interoperable and defined according to a collaborative process.

Z-buffer image assembly processing in high parallel visualization processing

International Nuclear Information System (INIS)

Kaneko, Isamu; Muramatsu, Kazuhiro

2000-03-01

On the platform of the parallel computer with many processors, the domain decomposition method is used as a popular means of parallel processing. In these days when the simulation scale becomes much larger and takes a lot of time, the simultaneous visualization processing with the actual computation is much more needed, and especially in case of a real-time visualization, the domain decomposition technique is indispensable. In case of parallel rendering processing, the rendered results must be gathered to one processor to compose the integrated picture in the last stage. This integration is usually conducted by the method using Z-buffer values. This process, however, induces the crucial problems of much lower speed processing and local memory shortage in case of parallel processing exceeding more than several tens of processors. In this report, the two new solutions are proposed. The one is the adoption of a special operator (Reduce operator) in the parallelization process, and the other is a buffer compression by deleting the background informations. This report includes the performance results of these new techniques to investigate their effect with use of the parallel computer Paragon. (author)

Explosive processes in nucleosynthesis

International Nuclear Information System (INIS)

Boyd, R.N.

2002-01-01

There are many explosive processes in nucleosynthesis: big bang nucleosynthesis, the rp-process, the γ-process, the ν-process, and the r-process. However, I will discuss just the rp-process and the r-process in detail, primarily because both seem to have been very active research areas of late, and because they have great potential for studies with radioactive nuclear beams. I will also discuss briefly the γ-process because of its inevitability in conjunction with the rp-process. (orig.)

Processing Depth, Elaboration of Encoding, Memory Stores, and Expended Processing Capacity.

Science.gov (United States)

Eysenck, Michael W.; Eysenck, M. Christine

1979-01-01

The effects of several factors on expended processing capacity were measured. Expended processing capacity was greater when information was retrieved from secondary memory than from primary memory, when processing was of a deep, semantic nature than when it was shallow and physical, and when processing was more elaborate. (Author/GDC)

Sewer Processes

DEFF Research Database (Denmark)

Hvitved-Jacobsen, Thorkild; Vollertsen, Jes; Nielsen, Asbjørn Haaning

Since the first edition was published over a decade ago, advancements have been made in the design, operation, and maintenance of sewer systems, and new problems have emerged. For example, sewer processes are now integrated in computer models, and simultaneously, odor and corrosion problems caused...... by hydrogen sulfide and other volatile organic compounds, as well as other potential health issues, have caused environmental concerns to rise. Reflecting the most current developments, Sewer Processes: Microbial and Chemical Process Engineering of Sewer Networks, Second Edition, offers the reader updated...... and valuable information on the sewer as a chemical and biological reactor. It focuses on how to predict critical impacts and control adverse effects. It also provides an integrated description of sewer processes in modeling terms. This second edition is full of illustrative examples and figures, includes...

AN OVERVIEW OF PHARMACEUTICAL PROCESS VALIDATION AND PROCESS CONTROL VARIABLES OF TABLETS MANUFACTURING PROCESSES IN INDUSTRY

OpenAIRE

Mahesh B. Wazade*, Sheelpriya R. Walde and Abhay M. Ittadwar

2012-01-01

Validation is an integral part of quality assurance; the product quality is derived from careful attention to a number of factors including selection of quality parts and materials, adequate product and manufacturing process design, control of the process variables, in-process and end-product testing. Recently validation has become one of the pharmaceutical industry’s most recognized and discussed subjects. It is a critical success factor in product approval and ongoing commercialization, fac...

Phenomena based Methodology for Process Synthesis incorporating Process Intensification

DEFF Research Database (Denmark)

Lutze, Philip; Babi, Deenesh Kavi; Woodley, John

2013-01-01

at processes at the lowest level of aggregation which is the phenomena level. In this paper, a phenomena based synthesis/design methodology incorporating process intensification is presented. Using this methodology, a systematic identification of necessary and desirable (integrated) phenomena as well......Process intensification (PI) has the potential to improve existing as well as conceptual processes, in order to achieve a more sustainable production. PI can be achieved at different levels. That is, the unit operations, functional and/or phenomena level. The highest impact is expected by looking...... as generation and screening of phenomena based flowsheet options are presented using a decomposition based solution approach. The developed methodology as well as necessary tools and supporting methods are highlighted through a case study involving the production of isopropyl-acetate....

Minimal and careful processing

OpenAIRE

Nielsen, Thorkild

2004-01-01

In several standards, guidelines and publications, organic food processing is strongly associated with "minimal processing" and "careful processing". The term "minimal processing" is nowadays often used in the general food processing industry and described in literature. The term "careful processing" is used more specifically within organic food processing but is not yet clearly defined. The concept of carefulness seems to fit very well with the processing of organic foods, especially if it i...

The Newest Laser Processing

International Nuclear Information System (INIS)

Lee, Baek Yeon

2007-01-01

This book mentions laser processing with laser principle, laser history, laser beam property, laser kinds, foundation of laser processing such as laser oscillation, characteristic of laser processing, laser for processing and its characteristic, processing of laser hole including conception of processing of laser hole and each material, and hole processing of metal material, cut of laser, reality of cut, laser welding, laser surface hardening, application case of special processing and safety measurement of laser.

Process Integration Analysis of an Industrial Hydrogen Production Process

OpenAIRE

Stolten, Detlef; Grube, Thomas; Tock, Laurence; Maréchal, François; Metzger, Christian; Arpentinier, Philippe

2010-01-01

The energy efficiency of an industrial hydrogen production process using steam methane reforming (SMR) combined with the water gas shift reaction (WGS) is analyzed using process integration techniques based on heat cascade calculation and pinch analysis with the aim of identifying potential measures to enhance the process performance. The challenge is to satisfy the high temperature heat demand of the SMR reaction by minimizing the consumption of natural gas to feed the combustion and to expl...

Developing engineering processes through integrated modelling of product and process

DEFF Research Database (Denmark)

Nielsen, Jeppe Bjerrum; Hvam, Lars

2012-01-01

This article aims at developing an operational tool for integrated modelling of product assortments and engineering processes in companies making customer specific products. Integrating a product model in the design of engineering processes will provide a deeper understanding of the engineering...... activities as well as insight into how product features affect the engineering processes. The article suggests possible ways of integrating models of products with models of engineering processes. The models have been tested and further developed in an action research study carried out in collaboration...... with a major international engineering company....

Process-based costing.

Science.gov (United States)

Lee, Robert H; Bott, Marjorie J; Forbes, Sarah; Redford, Linda; Swagerty, Daniel L; Taunton, Roma Lee

2003-01-01

Understanding how quality improvement affects costs is important. Unfortunately, low-cost, reliable ways of measuring direct costs are scarce. This article builds on the principles of process improvement to develop a costing strategy that meets both criteria. Process-based costing has 4 steps: developing a flowchart, estimating resource use, valuing resources, and calculating direct costs. To illustrate the technique, this article uses it to cost the care planning process in 3 long-term care facilities. We conclude that process-based costing is easy to implement; generates reliable, valid data; and allows nursing managers to assess the costs of new or modified processes.

Colloid process engineering

CERN Document Server

Peukert, Wolfgang; Rehage, Heinz; Schuchmann, Heike

2015-01-01

This book deals with colloidal systems in technical processes and the influence of colloidal systems by technical processes. It explores how new measurement capabilities can offer the potential for a dynamic development of scientific and engineering, and examines the origin of colloidal systems and its use for new products. The future challenges to colloidal process engineering are the development of appropriate equipment and processes for the production and obtainment of multi-phase structures and energetic interactions in market-relevant quantities. The book explores the relevant processes and for controlled production and how they can be used across all scales.

Laser Processing of Multilayered Thermal Spray Coatings: Optimal Processing Parameters

Science.gov (United States)

Tewolde, Mahder; Zhang, Tao; Lee, Hwasoo; Sampath, Sanjay; Hwang, David; Longtin, Jon

2017-12-01

Laser processing offers an innovative approach for the fabrication and transformation of a wide range of materials. As a rapid, non-contact, and precision material removal technology, lasers are natural tools to process thermal spray coatings. Recently, a thermoelectric generator (TEG) was fabricated using thermal spray and laser processing. The TEG device represents a multilayer, multimaterial functional thermal spray structure, with laser processing serving an essential role in its fabrication. Several unique challenges are presented when processing such multilayer coatings, and the focus of this work is on the selection of laser processing parameters for optimal feature quality and device performance. A parametric study is carried out using three short-pulse lasers, where laser power, repetition rate and processing speed are varied to determine the laser parameters that result in high-quality features. The resulting laser patterns are characterized using optical and scanning electron microscopy, energy-dispersive x-ray spectroscopy, and electrical isolation tests between patterned regions. The underlying laser interaction and material removal mechanisms that affect the feature quality are discussed. Feature quality was found to improve both by using a multiscanning approach and an optional assist gas of air or nitrogen. Electrically isolated regions were also patterned in a cylindrical test specimen.

Application of statistical process control and process capability analysis procedures in orbiter processing activities at the Kennedy Space Center

Science.gov (United States)

Safford, Robert R.; Jackson, Andrew E.; Swart, William W.; Barth, Timothy S.

1994-01-01

Successful ground processing at KSC requires that flight hardware and ground support equipment conform to specifications at tens of thousands of checkpoints. Knowledge of conformance is an essential requirement for launch. That knowledge of conformance at every requisite point does not, however, enable identification of past problems with equipment, or potential problem areas. This paper describes how the introduction of Statistical Process Control and Process Capability Analysis identification procedures into existing shuttle processing procedures can enable identification of potential problem areas and candidates for improvements to increase processing performance measures. Results of a case study describing application of the analysis procedures to Thermal Protection System processing are used to illustrate the benefits of the approaches described in the paper.

Westinghouse modular grinding process - improvement for follow on processes

Energy Technology Data Exchange (ETDEWEB)

Fehrmann, Henning [Westinghouse Germany GmbH, Mannheim, State (Germany)

2013-07-01

In nuclear power plants (NPP) ion exchange (IX) resins are used in several systems for water treatment. The resins can be in bead or powdered form. For waste treatment of spent IX resins, two methods are basically used: Direct immobilization (e.g. with cement, bitumen, polymer or High Integrity Container (HIC)); Thermal treatment (e.g. drying, oxidation or pyrolysis). Bead resins have some properties (e.g. particle size and density) that can have negative impacts on following waste treatment processes. Negative impacts could be: Floatation of bead resins in cementation process; Sedimentation in pipeline during transportation; Poor compaction properties for Hot Resin Supercompaction (HRSC). Reducing the particle size of the bead resins can have beneficial effects enhancing further treatment processes and overcoming prior mentioned effects. Westinghouse Electric Company has developed a modular grinding process to crush/grind the bead resins. This modular process is designed for flexible use and enables a selective adjustment of particle size to tailor the grinding system to the customer needs. The system can be equipped with a crusher integrated in the process tank and if necessary a colloid mill. The crusher reduces the bead resins particle size and converts the bead resins to a pump able suspension with lower sedimentation properties. With the colloid mill the resins can be ground to a powder. Compared to existing grinding systems this equipment is designed to minimize radiation exposure of the worker during operation and maintenance. Using the crushed and/or ground bead resins has several beneficial effects like facilitating cementation process and recipe development, enhancing oxidation of resins, improving the Hot Resin Supercompaction volume reduction performance. (authors)

Westinghouse modular grinding process - improvement for follow on processes

International Nuclear Information System (INIS)

Fehrmann, Henning

2013-01-01

In nuclear power plants (NPP) ion exchange (IX) resins are used in several systems for water treatment. The resins can be in bead or powdered form. For waste treatment of spent IX resins, two methods are basically used: Direct immobilization (e.g. with cement, bitumen, polymer or High Integrity Container (HIC)); Thermal treatment (e.g. drying, oxidation or pyrolysis). Bead resins have some properties (e.g. particle size and density) that can have negative impacts on following waste treatment processes. Negative impacts could be: Floatation of bead resins in cementation process; Sedimentation in pipeline during transportation; Poor compaction properties for Hot Resin Supercompaction (HRSC). Reducing the particle size of the bead resins can have beneficial effects enhancing further treatment processes and overcoming prior mentioned effects. Westinghouse Electric Company has developed a modular grinding process to crush/grind the bead resins. This modular process is designed for flexible use and enables a selective adjustment of particle size to tailor the grinding system to the customer needs. The system can be equipped with a crusher integrated in the process tank and if necessary a colloid mill. The crusher reduces the bead resins particle size and converts the bead resins to a pump able suspension with lower sedimentation properties. With the colloid mill the resins can be ground to a powder. Compared to existing grinding systems this equipment is designed to minimize radiation exposure of the worker during operation and maintenance. Using the crushed and/or ground bead resins has several beneficial effects like facilitating cementation process and recipe development, enhancing oxidation of resins, improving the Hot Resin Supercompaction volume reduction performance. (authors)

Defense waste processing facility precipitate hydrolysis process

International Nuclear Information System (INIS)

Doherty, J.P.; Eibling, R.E.; Marek, J.C.

1986-03-01

Sodium tetraphenylborate and sodium titanate are used to assist in the concentration of soluble radionuclide in the Savannah River Plant's high-level waste. In the Defense Waste Processing Facility, concentrated tetraphenylborate/sodium titanate slurry containing cesium-137, strontium-90 and traces of plutonium from the waste tank farm is hydrolyzed in the Salt Processing Cell forming organic and aqueous phases. The two phases are then separated and the organic phase is decontaminated for incineration outside the DWPF building. The aqueous phase, containing the radionuclides and less than 10% of the original organic, is blended with the insoluble radionuclides in the high-level waste sludge and is fed to the glass melter for vitrification into borosilicate glass. During the Savannah River Laboratory's development of this process, copper (II) was found to act as a catalyst during the hydrolysis reactions, which improved the organic removal and simplified the design of the reactor

On some applications of diffusion processes for image processing

International Nuclear Information System (INIS)

Morfu, S.

2009-01-01

We propose a new algorithm inspired by the properties of diffusion processes for image filtering. We show that purely nonlinear diffusion processes ruled by Fisher equation allows contrast enhancement and noise filtering, but involves a blurry image. By contrast, anisotropic diffusion, described by Perona and Malik algorithm, allows noise filtering and preserves the edges. We show that combining the properties of anisotropic diffusion with those of nonlinear diffusion provides a better processing tool which enables noise filtering, contrast enhancement and edge preserving.

Grind hardening process

CERN Document Server

Salonitis, Konstantinos

2015-01-01

This book presents the grind-hardening process and the main studies published since it was introduced in 1990s.  The modelling of the various aspects of the process, such as the process forces, temperature profile developed, hardness profiles, residual stresses etc. are described in detail. The book is of interest to the research community working with mathematical modeling and optimization of manufacturing processes.

Testing of a Rotary Micro-filter for Hanford Applications

International Nuclear Information System (INIS)

Poirier, M.R.; Herman, D.T.; Stefanko, D.B.; Fink, S.D.

2009-01-01

Savannah River National Laboratory (SRNL) researchers are investigating and developing a rotary micro-filter for solid-liquid separation applications with emphasis on deployment in radioactive services. The Department of Energy (DOE) Office of Waste Processing employed the SRNL team to evaluate the use of this rotary micro-filter for the Hanford Supplemental Pretreatment process. The authors tested a full-scale, 25-disk filter unit containing 0.5 μ filter media using a Hanford Tank AN-105 simulant at solids loadings of 0.06, 0.29, and 1.29 wt %. Based on recommendations from prior tests, the authors modified the filter unit by replacing the primary mechanical seal with an air seal. They also replaced the bushing with alternate materials of construction aimed at extended mean time between maintenance events. The testing provides the following conclusions. - The rotary filter produces a higher flux than the crossflow filter for the Hanford simulant. The gain in performance is less than previously seen for Savannah River Site simulants. - Filtrate clarity proved excellent with turbidity of <4 NTU (nephelometric turbidity units) in all samples. - Inspection of the primary mechanical seal faces after ∼140 hours of operation showed an expected minimal amount of initial wear, no passing of process fluid through the seal faces, and very little change in the air channeling grooves on the stationary face. - Some polishing of surfaces occurred at the bottom of the shaft bushing. The authors recommend improving the shaft bushing by holding it in place with a locking ring and incorporating grooves to provide additional cooling. - The authors recommend that Hanford test other pore size media to determine the optimum pore size for Hanford waste. - During final facility operation, the filter should be rinsed with filtrate or dilute caustic and drained prior to an extended shutdown to prevent the formation of a layer of settled solids on top of the filter disks. (authors)

Sustainable Management of Flowback Water during Hydraulic Fracturing of Marcellus Shale for Natural Gas Production

Energy Technology Data Exchange (ETDEWEB)

Vidic, Radisav [Univ. of Pittsburgh, PA (United States)

2015-01-24

This study evaluated the feasibility of using abandoned mine drainage (AMD) as make- up water for the reuse of produced water for hydraulic fracturing. There is an abundance of AMD sources near permitted gas wells as documented in this study that can not only serve as makeup water and reduce the demand on high quality water resources but can also as a source of chemicals to treat produced water prior to reuse. The assessment of AMD availability for this purpose based on proximity and relevant regulations was accompanied by bench- and pilot-scale studies to determine optimal treatment to achieve desired water quality for use in hydraulic fracturing. Sulfate ions that are often present in AMD at elevated levels will react with Ba²⁺ and Sr²⁺ in produced water to form insoluble sulfate compounds. Both membrane microfiltration and gravity separation were evaluated for the removal of solids formed as a result of mixing these two impaired waters. Laboratory studies revealed that neither AMD nor barite formed in solution had significant impact on membrane filtration but that some produced waters contained submicron particles that can cause severe fouling of microfiltration membrane. Coagulation/flocculation was found to be an effective process for the removal of suspended solids and both bench- and pilot-scale studies revealed that optimal process conditions can consistently achieve the turbidity of the finished water below 5 NTU. Adjusting the blending ratio of AMD and produced water can achieve the desired effluent sulfate concentration that can be accurately predicted by chemical thermodynamics. Co-treatment of produced water and AMD will result in elevated levels of naturally occurring radioactive materials (NORM) in the solid waste generated in this process due to radium co-precipitation with barium sulfate. Laboratory studies revealed that the mobility of barite that may form in the subsurface due to the presence of sulfate in the fracturing fluid can be

Transuranium processing plant

International Nuclear Information System (INIS)

King, L.J.

1983-01-01

The Transuranium Processing Plant (TRU) is a remotely operated, hot-cell, chemical processing facility of advanced design. The heart of TRU is a battery of nine heavily shielded process cells housed in a two-story building. Each cell, with its 54-inch-thick walls of a special high-density concrete, has enough shielding to stop the neutrons and gamma radiation from 1 gram of 252/sub Cf/ and associated fission products. Four cells contain chemical processing equipment, three contain equipment for the preparation and inspection of HFIR targets, and two cells are used for analytical chemistry operations. In addition, there are eight laboratories used for process development, for part of the process-control analyses, and for product finishing operations. Although the Transuranium Processing Plant was built for the purpose of recovering transuranium elements from targets irradiated in the High Flux Isotope Reactor (HFIR), it is also a highly versatile facility which has extensive provisions for changing and modifying equipment. Thus, it was a relatively simple matter to install a Solvent Extraction Test Facility (SETF) in one of the TRU chemical processing cells for use in the evaluation and demonstration of solvent extraction flowsheets for the recovery of fissile and fertile materials from irradiated reactor fuels. The equipment in the SETF has been designed for process development and demonstrations and the particular type of mixer-settler contactors was chosen because it is easy to observe and sample

Welding processes handbook

CERN Document Server

Weman, Klas

2003-01-01

Deals with the main commercially significant and commonly used welding processes. This title takes the student or novice welder through the individual steps involved in each process in an easily understood way. It covers many of the requirements referred to in European Standards including EN719, EN 729, EN 729 and EN 287.$bWelding processes handbook is a concise, explanatory guide to the main commercially significant and commonly-used welding processes. It takes the novice welder or student through the individual steps involved in each process in a clear and easily understood way. It is intended to provide an up-to-date reference to the major applications of welding as they are used in industry. The contents have been arranged so that it can be used as a textbook for European welding courses in accordance with guidelines from the European Welding Federation. Welding processes and equipment necessary for each process are described so that they can be applied to all instruction levels required by the EWF and th...

Kidney transplantation process in Brazil represented in business process modeling notation.

Science.gov (United States)

Peres Penteado, A; Molina Cohrs, F; Diniz Hummel, A; Erbs, J; Maciel, R F; Feijó Ortolani, C L; de Aguiar Roza, B; Torres Pisa, I

2015-05-01

Kidney transplantation is considered to be the best treatment for people with chronic kidney failure, because it improves the patients' quality of life and increases their length of survival compared with patients undergoing dialysis. The kidney transplantation process in Brazil is defined through laws, decrees, ordinances, and resolutions, but there is no visual representation of this process. The aim of this study was to analyze official documents to construct a representation of the kidney transplantation process in Brazil with the use of business process modeling notation (BPMN). The methodology for this study was based on an exploratory observational study, document analysis, and construction of process diagrams with the use of BPMN. Two rounds of validations by specialists were conducted. The result includes the kidney transplantation process in Brazil representation with the use of BPMN. We analyzed 2 digital documents that resulted in 2 processes with 45 total of activities and events, 6 organizations involved, and 6 different stages of the process. The constructed representation makes it easier to understand the rules for the business of kidney transplantation and can be used by the health care professionals involved in the various activities within this process. Construction of a representation with language appropriate for the Brazilian lay public is underway. Copyright © 2015 Elsevier Inc. All rights reserved.

High temperature nuclear process heat systems for chemical processes

International Nuclear Information System (INIS)

Jiacoletti, R.J.

1976-01-01

The development planning and status of the very high temperature gas cooled reactor as a source of industrial process heat is presented. The dwindling domestic reserves of petroleum and natural gas dictate major increases in the utilization of coal and nuclear sources to meet the national energy demand. The nuclear process heat system offers a unique combination of the two that is environmentally and economically attractive and technically sound. Conceptual studies of several energy-intensive processes coupled to a nuclear heat source are presented

Process development

International Nuclear Information System (INIS)

Zapata G, G.

1989-01-01

Process development: The paper describes the organization and laboratory facilities of the group working on radioactive ore processing studies. Contains a review of the carried research and the plans for the next future. A list of the published reports is also presented

Information Technology Process Improvement Decision-Making: An Exploratory Study from the Perspective of Process Owners and Process Managers

Science.gov (United States)

Lamp, Sandra A.

2012-01-01

There is information available in the literature that discusses information technology (IT) governance and investment decision making from an executive-level perception, yet there is little information available that offers the perspective of process owners and process managers pertaining to their role in IT process improvement and investment…

Process synthesis, design and analysis using a process-group contribution method

DEFF Research Database (Denmark)

Kumar Tula, Anjan; Eden, Mario R.; Gani, Rafiqul

2015-01-01

) techniques. The fundamental pillars of this framework are the definition and use of functional process-groups (building blocks) representing a wide range of process operations, flowsheet connectivity rules to join the process-groups to generate all the feasible flowsheet alternatives and flowsheet property...... models like energy consumption, atom efficiency, environmental impact to evaluate the performance of the generated alternatives. In this way, a list of feasible flowsheets are quickly generated, screened and selected for further analysis. Since the flowsheet is synthesized and the operations......This paper describes the development and application of a process-group contribution method to model, simulate and synthesize chemical processes. Process flowsheets are generated in the same way as atoms or groups of atoms are combined to form molecules in computer aided molecular design (CAMD...

Development of interface technology between unit processes in E-Refining process

Energy Technology Data Exchange (ETDEWEB)

Lee, S. H.; Lee, H. S.; Kim, J. G. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2010-10-15

The pyroprocessing is composed mainly four subprocesses, such as an electrolytic reduction, an electrorefining, an electrowinning, and waste salt regeneration/ solidification processes. The electrorefining process, one of main processes which are composed of pyroprocess to recover the useful elements from spent fuel, is under development by Korea Atomic Energy Research Institute as a sub process of pyrochemical treatment of spent PWR fuel. The CERS(Continuous ElectroRefining System) is composed of some unit processes such as an electrorefiner, a salt distiller, a melting furnace for the U-ingot and U-chlorinator (UCl{sub 3} making equipment) as shown in Fig. 1. In this study, the interfaces technology between unit processes in E-Refining system is investigated and developed for the establishment of integrated E-Refining operation system as a part of integrated pyroprocessing

A secondary fuel removal process: plasma processing

Energy Technology Data Exchange (ETDEWEB)

Min, J Y; Kim, Y S [Hanyang Univ., Seoul (Korea, Republic of); Bae, K K; Yang, M S [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1997-07-01

Plasma etching process of UO{sub 2} by using fluorine containing gas plasma is studied as a secondary fuel removal process for DUPIC (Direct Use of PWR spent fuel Into Candu) process which is taken into consideration for potential future fuel cycle in Korea. CF{sub 4}/O{sub 2} gas mixture is chosen for reactant gas and the etching rates of UO{sub 2} by the gas plasma are investigated as functions of CF{sub 4}/O{sub 2} ratio, plasma power, substrate temperature, and plasma gas pressure. It is found that the optimum CF{sub 4}/O{sub 2} ratio is around 4:1 at all temperatures up to 400 deg C and the etching rate increases with increasing r.f. power and substrate temperature. Under 150W r.f. power the etching rate reaches 1100 monolayers/min at 400 deg C, which is equivalent to about 0.5mm/min. (author).

Clinical Process Intelligence

DEFF Research Database (Denmark)

Vilstrup Pedersen, Klaus

2006-01-01

.e. local guidelines. From a knowledge management point of view, this externalization of generalized processes, gives the opportunity to learn from, evaluate and optimize the processes. "Clinical Process Intelligence" (CPI), will denote the goal of getting generalized insight into patient centered health...

Sustainable processing

DEFF Research Database (Denmark)

Kristensen, Niels Heine

2004-01-01

Kristensen_NH and_Beck A: Sustainable processing. In Otto Schmid, Alexander Beck and Ursula Kretzschmar (Editors) (2004): Underlying Principles in Organic and "Low-Input Food" Processing - Literature Survey. Research Institute of Organic Agriculture FiBL, CH-5070 Frick, Switzerland. ISBN 3-906081-58-3...

Food processing

NARCIS (Netherlands)

Teodorowicz, Malgorzata; Neerven, Van Joost; Savelkoul, Huub

2017-01-01

The majority of foods that are consumed in our developed society have been processed. Processing promotes a non-enzymatic reaction between proteins and sugars, the Maillard reaction (MR). Maillard reaction products (MRPs) contribute to the taste, smell and color of many food products, and thus

Using Process Mining to Learn from Process Changes in Evolutionary Systems

NARCIS (Netherlands)

Günther, Christian W.; Rinderle, S.B.; Reichert, M.U.; van der Aalst, Wil M.P.; Recker, Jan

2008-01-01

Traditional information systems struggle with the requirement to provide flexibility and process support while still enforcing some degree of control. Accordingly, adaptive process management systems (PMSs) have emerged that provide some flexibility by enabling dynamic process changes during

REALIZING BUSINESS PROCESS MANAGEMENT BY HELP OF A PROCESS MAPPING DATABASE TOOL

CERN Document Server

Vergili, Ceren

2016-01-01

In a typical business sector, processes are the building blocks of the achievement. A considerable percentage of the processes are consisting of business processes. This fact is bringing the fact that business sectors are in need of a management discipline. Business Process Management (BPM) is a discipline that combines modelling, automation, execution, control, measurement, and optimization of process by considering enterprise goals, spanning systems, employees, customers, and partners. CERN’s EN – HE – HM section desires to apply the BPM discipline appropriately for improving their necessary technical, administrative and managerial actions to supply appropriate CERN industrial transport, handling and lifting equipment and to maintain it. For this reason, a Process Mapping Database Tool is created to develop a common understanding about how the section members can visualize their processes, agree on quality standards and on how to improve. It provides a management support by establishing Process Charts...

Multimodal Processes Rescheduling

DEFF Research Database (Denmark)

Bocewicz, Grzegorz; Banaszak, Zbigniew A.; Nielsen, Peter

2013-01-01

Cyclic scheduling problems concerning multimodal processes are usually observed in FMSs producing multi-type parts where the Automated Guided Vehicles System (AGVS) plays a role of a material handling system. Schedulability analysis of concurrently flowing cyclic processes (SCCP) exe-cuted in the......Cyclic scheduling problems concerning multimodal processes are usually observed in FMSs producing multi-type parts where the Automated Guided Vehicles System (AGVS) plays a role of a material handling system. Schedulability analysis of concurrently flowing cyclic processes (SCCP) exe...

Process-aware information systems : lessons to be learned from process mining

NARCIS (Netherlands)

Aalst, van der W.M.P.; Jensen, K.; Aalst, van der W.M.P.

2009-01-01

A Process-Aware Information System (PAIS) is a software system that manages and executes operational processes involving people, applications, and/or information sources on the basis of process models. Example PAISs are workflow management systems, case-handling systems, enterprise information

Applicability of product-driven process synthesis to separation processes in food

NARCIS (Netherlands)

Jankowiak, L.; Goot, van der A.J.; Trifunovic, O.; Bongers, P.; Boom, R.M.

2012-01-01

The demand for more sustainable processing in the food industry is rising but requires structured methodologies to support the fast implementation of new economic and sustainable processes. Product-driven process synthesis (PDPS) is a recently established methodology facilitating the rapid

Synroc processing options

International Nuclear Information System (INIS)

Rozsa, R.B.; Hoenig, C.L.

1981-01-01

Synroc is a titanate-based ceramic material currently being developed for immobilizing high-level nuclear reactor wastes in solid form. Synroc D is a unique variation of Synroc. It can contain the high-level defense wastes, particularly those in storage at the Savannah River Plant. In this report, we review the early development of the initial Synroc process, discuss modification and other options that simplify it overall, and recommend the future direction of research and development in the processing area. A reference Synroc process is described briefly and contrasted with the Savannah River Laboratory glass-based reference case. Preliminary engineering layouts show Synroc to be a more complex processing operation and, thus, more expensive than the glass-based process. However, we believe that simplifications, which will significantly reduce the cost difference, are possible. Further research and development will continue in the areas of slurry processing, fluidized bed calcination, and mineralization. This last will use sintering, hot uniaxial pressing, or hot isostatic pressing

Design Processes

DEFF Research Database (Denmark)

Ovesen, Nis

2009-01-01

Inspiration for most research and optimisations on design processes still seem to focus within the narrow field of the traditional design practise. The focus in this study turns to associated businesses of the design professions in order to learn from their development processes. Through interviews...... and emerging production methods....

Process modeling style

CERN Document Server

Long, John

2014-01-01

Process Modeling Style focuses on other aspects of process modeling beyond notation that are very important to practitioners. Many people who model processes focus on the specific notation used to create their drawings. While that is important, there are many other aspects to modeling, such as naming, creating identifiers, descriptions, interfaces, patterns, and creating useful process documentation. Experience author John Long focuses on those non-notational aspects of modeling, which practitioners will find invaluable. Gives solid advice for creating roles, work produ

Improving Healthcare Logistics Processes

DEFF Research Database (Denmark)

Feibert, Diana Cordes

logistics processes in hospitals and aims to provide theoretically and empirically based evidence for improving these processes to both expand the knowledge base of healthcare logistics and provide a decision tool for hospital logistics managers to improve their processes. Case studies were conducted...... processes. Furthermore, a method for benchmarking healthcare logistics processes was developed. Finally, a theoretically and empirically founded framework was developed to support managers in making an informed decision on how to improve healthcare logistics processes. This study contributes to the limited...... literature concerned with the improvement of logistics processes in hospitals. Furthermore, the developed framework provides guidance for logistics managers in hospitals on how to improve their processes given the circumstances in which they operate....

Nuclear process heat

International Nuclear Information System (INIS)

Barnert, H.; Hohn, H.; Schad, M.; Schwarz, D.; Singh, J.

1993-01-01

In a system for the application of high temperature heat from the HTR one must distinguish between the current generation and the use of process heat. In this respect it is important that the current can be generated by dual purpose power plants. The process heat is used as sensible heat, vaporisation heat and as chemical energy at the chemical conversion for the conversion of raw materials, the refinement of fossil primary energy carriers and finally circuit processes for the fission of water. These processes supply the market for heat, fuels, motor fuels and basic materials. Fifteen examples of HTR heat processes from various projects and programmes are presented in form of energy balances, however in a rather short way. (orig./DG) [de

Business process support

Energy Technology Data Exchange (ETDEWEB)

Carle, Adriana; Fiducia, Daniel [Transportadora de Gas del Sur S.A. (TGS), Buenos Aires (Argentina)

2005-07-01

This paper is about the own development of business support software. The developed applications are used to support two business processes: one of them is the process of gas transportation and the other is the natural gas processing. This software has interphases with the ERP SAP, software SCADA and on line gas transportation simulation software. The main functionalities of the applications are: entrance on line real time of clients transport nominations, transport programming, allocation of the clients transport nominations, transport control, measurements, balanced pipeline, allocation of gas volume to the gas processing plants, calculate of product tons processed in each plant and tons of product distributed to clients. All the developed software generates information to the internal staff, regulatory authorities and clients. (author)

Process for making unsaturated hydrocarbons using microchannel process technology

Science.gov (United States)

Tonkovich, Anna Lee [Dublin, OH; Yuschak, Thomas [Lewis Center, OH; LaPlante, Timothy J [Columbus, OH; Rankin, Scott [Columbus, OH; Perry, Steven T [Galloway, OH; Fitzgerald, Sean Patrick [Columbus, OH; Simmons, Wayne W [Dublin, OH; Mazanec, Terry Daymo, Eric

2011-04-12

The disclosed invention relates to a process for converting a feed composition comprising one or more hydrocarbons to a product comprising one or more unsaturated hydrocarbons, the process comprising: flowing the feed composition and steam in contact with each other in a microchannel reactor at a temperature in the range from about 200.degree. C. to about 1200.degree. C. to convert the feed composition to the product, the process being characterized by the absence of catalyst for converting the one or more hydrocarbons to one or more unsaturated hydrocarbons. Hydrogen and/or oxygen may be combined with the feed composition and steam.

Correlation between radwaste processing and hazardous waste treatment processes

International Nuclear Information System (INIS)

Block, O.U.J.; Tulipano, F.J.

1988-01-01

The basic framework under SARA has established that preferred remedies are those which permanently and significantly reduce toxicity, mobility or volume of wastes. In the 1970's radwaste process designs at power plants received pressure to satisfy essentially the same criteria when increased emphasis was placed on limited disposal sites which resulted in rapidly escalating disposal costs. This paper provides a historical perspective of radwaste experience and discusses valuable insight to hazardous waste treatment technologies. The radwaste system experience is discussed in terms of providing a source of proven and reliable technologies. Discussion is presented on specific radwaste processes which are applicable technologies for hazardous waste treatment. The technologies presented include (a) Solidification, (b) Evaporation, and (c) Incineration. Experience is presented which establishes assurance that the treatment technologies will provide a permanent remedy to hazardous waste treatment. This paper describes typical radwaste solidification, evaporation and incineration processes at power plants. The design requirements and implementation of radwaste equipment is correlated to design requirement of hazardous waste equipment. Specific discussion is provided on how the available process equipment can reduce toxicity, mobility, and volume of waste. Discussion is presented on how the standard off the shelf processing equipment needs to be modified for radwaste and hazardous waste applications

Modeling Aspects of Activated Sludge Processes Part l l: Mathematical Process Modeling and Biokinetics of Activated Sludge Processes

Energy Technology Data Exchange (ETDEWEB)

AbdElHaleem, H S [Cairo Univ.-CivlI Eng. Dept., Giza (Egypt); EI-Ahwany, A H [CairoUlmrsity- Faculty ofEngincering - Chemical Engineering Department, Giza (Egypt); Ibrahim, H I [Helwan University- Faculty of Engineering - Biomedical Engineering Department, Helwan (Egypt); Ibrahim, G [Menofia University- Faculty of Engineering Sbebin EI Kom- Basic Eng. Sc. Dept., Menofia (Egypt)

2004-07-01

Mathematical process modeling and biokinetics of activated sludge process were reviewed considering different types of models. It has been evaluated the task group models of ASMI. and 2, and 3 versioned by Henze et al considering the conditions of each model and the different processes of which every model consists. It is revealed that ASMI contains some defects avoided in ASM3. Relied on homogeneity, Models can be classified into homogenous models characterized by taking the activated sludge process as one phase. In this type of models, the internal mass transfer inside the floes was neglected.. Hence, the kinetic parameter produces can be considered inaccurate. The other type of models is the heterogeneous model This type considers the mass transfer operations in addition to the biochemical reaction processes; hence, the resulted kinetic parameters can be considered more accurate than that of homogenous type.

Modeling Aspects of Activated Sludge Processes Part l l: Mathematical Process Modeling and Biokinetics of Activated Sludge Processes

International Nuclear Information System (INIS)

AbdElHaleem, H.S.; EI-Ahwany, A. H.; Ibrahim, H.I.; Ibrahim, G.

2004-01-01

Mathematical process modeling and biokinetics of activated sludge process were reviewed considering different types of models. It has been evaluated the task group models of ASMI. and 2, and 3 versioned by Henze et al considering the conditions of each model and the different processes of which every model consists. It is revealed that ASMI contains some defects avoided in ASM3. Relied on homogeneity, Models can be classified into homogenous models characterized by taking the activated sludge process as one phase. In this type of models, the internal mass transfer inside the floes was neglected.. Hence, the kinetic parameter produces can be considered inaccurate. The other type of models is the heterogeneous model This type considers the mass transfer operations in addition to the biochemical reaction processes; hence, the resulted kinetic parameters can be considered more accurate than that of homogenous type

Redução de cor ICUMSA em soluções concentradas de açúcar bruto por processo oxidativo com peróxido de hidrogênio

Directory of Open Access Journals (Sweden)

Juliana Lorenz Mandro

2017-05-01

Full Text Available Resumo A clarificação/purificação do açúcar refinado a partir de açúcares brutos, como Very High Polarization (VHP, é realizada atualmente pelo uso de resinas de troca-iônica ou carvão ativado. No entanto, são metodologias de alto custo, que necessitam de constante regeneração/recuperação e apresentam perda de capacidade em função do tempo de processamento. Neste sentido, estudos sobre tecnologias alternativas ao uso de resinas de troca-iônica e carvão ativado vêm sendo cada vez mais relacionados, para aumentar a economia do setor. O peróxido de hidrogênio em solução comercial (35%, v/v pode também ser entendido como agente promotor de redução de cor ICUMSA, na cadeia produtiva do açúcar refinado. Com isso, foram realizados tratamentos a fim de testar a eficiência do agente oxidante na clarificação de açúcar bruto do tipo VHP. Os tratamentos foram avaliados frente a diferentes doses de peróxido de hidrogênio, pH e temperaturas, durante um tempo reacional de uma hora. Todas as amostras tratadas apresentaram redução de cor ICUMSA, sendo que o maior decréscimo esteve na faixa de 67 a 70%. O aumento da dose de agente oxidante foi proporcional ao aumento de precipitados no meio, em que o tratamento com maior concentração de peróxido de hidrogênio apresentou índice de turbidez de 142 NTU em relação ao valor da amostra bruta (17 NTU, sendo o ensaio com maior turbidez. A degradação de sacarose ocorreu de forma mais pronunciada nos tratamentos com valores de pH abaixo de 5,0. Com isso, o peróxido de hidrogênio se mostrou uma alternativa viável para redução de cor ICUMSA e precipitação de não-açúcares e os tratamentos com melhor redução de cor também não foram críticos na degradação de sacarose.

Turbidity and oil removal from oilfield produced water, middle oil company by electrocoagulation technique

Directory of Open Access Journals (Sweden)

Mohammed Thamer

2018-01-01

Full Text Available Huge quantity of produced water is salty water trapped in the oil wells rock and brought up along with oil or gas during production. It usually contains hydrocarbons as oil and suspended solids or turbidity. Therefore the aim of this study is to treat produced water before being discharge to surface water or re injected in oil wells. In this paper experimental results were investigated on treating produced water (which is obtained from Middle Oil Company-Iraq, through electrocoagulation (EC. The performance of EC was investigated for reduction of turbidity and oil content up to allowable limit. Effect of different parameters were studied; (pH, current density, distance between two electrodes, and electrolysis time. The experimental runs carried out by an electrocoagulation unit was assembled and installed in the lab and the reactor was made of a material Perspex, with a capacity of approximately 2.5 liters and dimensions were 20 cm in length, 14 cm in width and 16 cm height. The electrodes employed were made of commercial materials. The anode was a perforated aluminum rectangular plate with a thickness of 1.72 mm, a height of 60 mm and length of 140 mm and the cathode was a mesh iron. The current was used in the unit with different densities to test the turbidity removing efficiency (0.0025, 0.00633, 0.01266 and 0.0253 A/cm2.The experiment showed that the best turbidity removing was (10, 9.7, 9.2, 18 NTU respectively. The distance between the electrodes of the unit was 3cm. The present turbidity removing was 92.33%. A slight improvement of turbidity removing was shown when the distance between the electrodes was changed from 0.5 to 3 cm with fixation of current density. The best turbidity removing was 93.5% , (7.79 NTU when the distance between the electrodes were 1 cm. The experimental results found that concentration of oil had decreased to (10.7, 11.2, 11.7, 12.3 mg/l when different current densities (0.00253, 0.00633, 0.01266, 0.0253 A/cm2

STUDI CAMPURAN SURFACTANT UNTUK MENENTUKAN FUNGSI SOLUBILIZER DAN FIXATIVE PADA INDUSTRI PARFUM

Directory of Open Access Journals (Sweden)

K N Adli

2016-03-01

Full Text Available Kualitas parfum  ditentukan oleh kejernihan dan longlasting parfum. Campuran surfaktan dapat meningkatkan kualitas parfum dengan biaya produksi yang murah. Penelitian ini bertujuan untuk mengkaji rasio campuran surfaktan untuk menentukan fungsi solubilizer dan fixative. Bibit parfum yang digunakan dalam penelitian ini adalah eugenol, surfaktan dengan fungsi solubilizer adalah portasol 40 dan tween 80 sedangkan surfaktan dengan fungsi fixative adalah glucam P20 dan patchouli alkohol. Rasio yang digunakan pada penelitian ini antara lain rasio glucam p20 : portasol (r G/P, rasio portasol 40 : tween 80 (r P/T dan rasio glucam P20 : patchouli alkohol (r G/PA. Hasil penelitian menunjukkan campuran surfaktan dapat meningkatkan kejernihan dan longlasting parfum lebih baik daripada surfaktan tunggal. Optimasi menggunakan RSM didapatkan rasio campuran yang paling berpengaruh terhadap kejernihan adalah r P/T sedangkan rasio yang paling berpengaruh terhadap longlasting parfum adalah r G/PA. Hasil optimum dengan respon turbiditas r G/P = 3,59; r P/T = 0,48; r G/PA = 0,41 dan respon longlasting  r G/P = 4,51; r P/T = 0,40; r G/PA = 0,42 menghasilkan turbiditas 0,0489 NTU serta longlasting 3,68 jam.Perfume quality is determined by the clarity and longlasting perfume. Surfactant mixture can improve the quality of perfumes at low production costs. This study objectives are to examines the blending ratio surfactant and to determine the function of solubilizer and fixative. Perfume seeds used in this study is eugenol, surfactants with solubilizer function is Portasol 40 and Tween 80 while surfactant with fixative function are glucam P20 and patchouli alcohol. The ratio used in this study include glucam ratio P20: portasol (r G/P, the ratio portasol 40: tween 80 (rP/T and the ratio of glucam P20: patchouli alcohol (r G/PA. The results showed a mixture of surfactants may improve the clarity and longlasting perfume is better than a single surfactant. RSM

KELIMPAHAN FITOPLANKTON DAN KONSENTRASI TSS SEBAGAI INDIKATOR PENENTU KONDISI PERAIRAN MUARA SUNGAI PORONG

Directory of Open Access Journals (Sweden)

Ulung Jantama Wisha

2016-11-01

Full Text Available Pembuangan limbah dan lumpur ke Sungai Porong diduga akan berdampak bagi lingkungan sekitarnya, khususnya meningkatnya konsentrasi padatan tersuspensi (TSS dan mempengaruhi sebaran fitoplankton di wilayah tersebut. Tujuan dari dilakukannya penelitian ini adalah untuk mengetahui konsentrasi muatan padatan tersuspensi, kekeruhan dan kelimpahan fitoplankton di perairan muara Sungai Porong, Kabupaten Sidoarjo. Metode penelitian yang digunakan adalah metode deskriptif. Data yang dikumpulkan sebagai variabel ukur adalah muatan padatan tersuspensi, kekeruhan, kelimpahan fitoplankton dan kecepatan serta arah arus. Variabel pendukung meliputi data pasang surut dan peta bathimetri wilayah muara Sungai Porong. Data yang diperoleh selanjutnya dianalisis menggunakan program Arc GIS 10, sehingga menghasilkan output berupa distribusi spasial. Konsentrasi muatan padatan tersuspensi 542-885 mg/l. konsentrasi kekeruhan 3.7-20.5 NTU. Kelimpahan fitoplankton 153-238 ind/l. Berdasarkan data tersebut dapat diketahui bahwa sebaran muatan padatan tersuspensi dan kekeruhan memiliki kaitan dengan kelimpahan fitoplankton pada saat surut, meskipun pada kuantitas yang tidak selalu sama. Arah sebaran bergerak ke arah Timur atau menjauhi muara sungai. ABUNDANCE OF PHYTOPLANKTON AND TSS VALUE AS AN INDICATOR FOR PORONG RIVER ESTUARY WATER CONDITIONSDisposal of waste and mud into Porong River is expected to have an impact to the surrounding environment, particularly the increasing concentration of suspended solids (TSS and affect the distribution of phytoplankton in the region. The purpose of this study was to determine the correlation between the concentration of TSS and abundance of phytoplankton as an indicator for determinate condition of Porong River Estuary. Determining the location of sampling by purposive sampling method. The data were then analyzed with statistical methods and spatially using ArcGIS 10 program. The concentration of suspended solids charge 542-885 mg

A Dual Process Approach to Understand Tourists’ Destination Choice Processes

DEFF Research Database (Denmark)

Kock, Florian; Josiassen, Alexander; Assaf, Albert

2017-01-01

Most studies that investigate tourists' choices of destinations apply the concept of mental destination representations, also referred to as destination image. The present study investigates tourists’ destination choice processes by conceptualizing how different components of destination image...... are mentally processed in tourists' minds. Specifically, the seminal dual processing approach is applied to the destination image literature. By doing this, we argue that some components of mental destination representations are processed systematically while others serve as inputs for heuristics...... that individuals apply to inform their decision making. Understanding how individuals make use of their mental destination representations and how they color their decision-making is essential in order to better explain tourist behavior....

Ornstein-Uhlenbeck Processes Simulation

OpenAIRE

Kuzmina, A.

2012-01-01

In this paper we give a brief introduction to Ornstein-Uhlenbeck processes and their simulation methods. Ornstein-Uhlenbeck processes were introduced by Barndorff-Nielsen and Shephard (2001) as a model to describe volatility in finance. Ornstein-Uhlenbeck processes are based on Levy processes. Levy processes simulation may be found in [1, 2].

Process heat. Triggering the processes

Energy Technology Data Exchange (ETDEWEB)

Augsten, Eva

2012-07-01

If solar process heat is to find a market, then the decision makers in industrial companies need to be aware that it actually exists. This was one of the main goals of the So-Pro project, which officially drew to a close in April 2012. (orig.)

Optimality of Poisson Processes Intensity Learning with Gaussian Processes

NARCIS (Netherlands)

Kirichenko, A.; van Zanten, H.

2015-01-01

In this paper we provide theoretical support for the so-called "Sigmoidal Gaussian Cox Process" approach to learning the intensity of an inhomogeneous Poisson process on a d-dimensional domain. This method was proposed by Adams, Murray and MacKay (ICML, 2009), who developed a tractable computational

Is There Dependence Between Process Maturity and Process Performance?

NARCIS (Netherlands)

Joost Spekschoor; Pascal Ravesteijn; Roeland Loggen; dr. Martijn Zoet

2012-01-01

During recent years the world has seen rapid changes such as globalization, the Internet, and the rise of new economies. To survive these changes organizations need to be in control of their processes, and be able to continuously improve the process performance. Therefore many organizations are

Stream-processing pipelines: processing of streams on multiprocessor architecture

NARCIS (Netherlands)

Kavaldjiev, N.K.; Smit, Gerardus Johannes Maria; Jansen, P.G.

In this paper we study the timing aspects of the operation of stream-processing applications that run on a multiprocessor architecture. Dependencies are derived for the processing and communication times of the processors in such a system. Three cases of real-time constrained operation and four

Detecting Difference between Process Models Based on the Refined Process Structure Tree

Directory of Open Access Journals (Sweden)

Jing Fan

2017-01-01

Full Text Available The development of mobile workflow management systems (mWfMS leads to large number of business process models. In the meantime, the location restriction embedded in mWfMS may result in different process models for a single business process. In order to help users quickly locate the difference and rebuild the process model, detecting the difference between different process models is needed. Existing detection methods either provide a dissimilarity value to represent the difference or use predefined difference template to generate the result, which cannot reflect the entire composition of the difference. Hence, in this paper, we present a new approach to solve this problem. Firstly, we parse the process models to their corresponding refined process structure trees (PSTs, that is, decomposing a process model into a hierarchy of subprocess models. Then we design a method to convert the PST to its corresponding task based process structure tree (TPST. As a consequence, the problem of detecting difference between two process models is transformed to detect difference between their corresponding TPSTs. Finally, we obtain the difference between two TPSTs based on the divide and conquer strategy, where the difference is described by an edit script and we make the cost of the edit script close to minimum. The extensive experimental evaluation shows that our method can meet the real requirements in terms of precision and efficiency.

Preliminary evaluation of alternative waste form solidification processes. Volume I. Identification of the processes

International Nuclear Information System (INIS)

Treat, R.L.; Nesbitt, J.F.; Blair, H.T.; Carter, J.G.; Gorton, P.S.; Partain, W.L.; Timmerman, C.L.

1980-04-01

This document contains preconceptual design data on 11 processes for the solidification and isolation of nuclear high-level liquid wastes (HLLW). The processes are: in-can glass melting (ICGM) process, joule-heated glass melting (JHGM) process, glass-ceramic (GC) process, marbles-in-lead (MIL) matrix process, supercalcine pellets-in-metal (SCPIM) matrix process, pyrolytic-carbon coated pellets-in-metal (PCCPIM) matrix process, supercalcine hot-isostatic-pressing (SCHIP) process, SYNROC hot-isostatic-pressing (SYNROC HIP) process, titanate process, concrete process, and cermet process. For the purposes of this study, it was assumed that each of the solidification processes is capable of handling similar amounts of HLLW generated in a production-sized fuel reprocessing plant. It was also assumed that each of the processes would be enclosed in a shielded canyon or cells within a waste facility located at the fuel reprocessing plant. Finally, it was assumed that all of the processes would be subject to the same set of regulations, codes and standards. Each of the solidification processes converts waste into forms that may be acceptable for geological disposal. Each process begins with the receipt of HLLW from the fuel reprocessing plant. In this study, it was assumed that the original composition of the HLLW would be the same for each process. The process ends when the different waste forms are enclosed in canisters or containers that are acceptable for interim storage. Overviews of each of the 11 processes and the bases used for their identification are presented in the first part of this report. Each process, including its equipment and its requirements, is covered in more detail in Appendices A through K. Pertinent information on the current state of the art and the research and development required for the implementation of each process are also noted in the appendices

Collection of Condensate Water: Global Potential and Water Quality Impacts

KAUST Repository

Loveless, Kolin Joseph

2012-12-28

Water is a valuable resource throughout the world, especially in hot, dry climates and regions experiencing significant population growth. Supplies of fresh water are complicated by the economic and political conditions in many of these regions. Technologies that can supply fresh water at a reduced cost are therefore becoming increasingly important and the impact of such technologies can be substantial. This paper considers the collection of condensate water from large air conditioning units as a possible method to alleviate water scarcity issues. Using the results of a climate model that tested data collected from 2000 to 2010, we have identified areas in the world with the greatest collection potential. We gave special consideration to areas with known water scarcities, including the coastal regions of the Arabian Peninsula, Sub-Saharan Africa and South Asia. We found that the quality of the collected water is an important criterion in determining the potential uses for this water. Condensate water samples were collected from a few locations in Saudi Arabia and detailed characterizations were conducted to determine the quality of this water. We found that the quality of condensate water collected from various locations and types of air conditioners was very high with conductivities reaching as low as 18 μS/cm and turbidities of 0. 041 NTU. The quality of the collected condensate was close to that of distilled water and, with low-cost polishing treatments, such as ion exchange resins and electrochemical processes, the condensate quality could easily reach that of potable water. © 2012 Springer Science+Business Media Dordrecht.

Development of a prototype GIS for risk-hazard assessment

International Nuclear Information System (INIS)

Devonport, C.

1992-01-01

A collaborative research agreement between the Supervising Scientist for the Alligator Rivers Region (OSS) and the Northern Territory University (NTU) aims to develop and assess a computer-based Geographic Information System (GIS) to integrate terrain and geological data for risk-hazard analysis and modelling. This paper outlines initial design and development of the prototype GIS including the input of trial data of various types. It is recognised that the GIS must be flexible enough to accommodate change and provide a base for a variety of research needs. Such functionality is likely to be provided best by an initially small, generic prototype GIS to which functions and data are added as required. Properties of the prototype identified as critical to its usefulness include integration of different types of data into the system, understanding and accommodating inconsistencies between data sets and the recognition and recording of error. Various types of data (elevation data, maps and images) available at the outset of the project are outlined together with a brief discussion on their source, integration into the database, derivative products and the potential usefulness of, and problems associated with, the different data formats. The analytical possibilities offered by the trial data will be explored next and the results of the first development cycle presented by the end of 1992. Subsequently, additional data will be incorporated into the database, analytical techniques will be used to build models, and user-driven development will enable the GIS to begin to support a decision research process. 20 refs

Dissolved air flotation of polishing wastewater from semiconductor manufacturer.

Science.gov (United States)

Liu, J C; Lien, C Y

2006-01-01

The feasibility of the dissolved air flotation (DAF) process in treating chemical mechanical polishing (CMP) wastewater was evaluated in this study. Wastewater from a local semiconductor manufacturer was sampled and characterised. Nano-sized silica (77.6 nm) with turbidity of 130 +/- 3 NTU was found in the slightly alkaline wastewater with traces of other pollutants. Experimental results indicated removal efficiency of particles, measured as suspended particle or turbidity, increased with increasing concentration of cationic collector cetyltrimethyl ammonium bromide (CTAB). When CTAB concentration was 30 mg/L, pH of 6.5 +/- 0.1 and recycle ratio of 30%, very effective removal of particles (> 98%) was observed in saturation pressure range of 4 to 6 kg/cm2, and the reaction proceeded faster under higher pressure. Similarly, the reaction was faster under the higher recycle ratio, while final removal efficiency improved slightly as the recycle ratio increased from 20 to 40%. An insignificant effect of pH on treatment efficiency was found as pH varied from 4.5 to 8.5. The presence of activator, Al3+ and Fe3+, enhanced the system performance. It is proposed that CTAB adsorbs on silica particles in polishing wastewater through electrostatic interaction and makes particles more hydrophobic. The increase in hydrophobicity results in more effective bubble-particle collisions. In addition, flocculation of silica particles through bridging effect of collector was found; it is believed that flocculation of particles also contributed to flotation. Better attachment between gas bubble and solid, higher buoyancy and higher air to solid ratio all lead to effective flotation.

Treatment of Wastewater From Car Washes Using Natural Coagulation and Filtration System

Science.gov (United States)

Al-Gheethi, A. A.; Mohamed, R. M. S. R.; Rahman, M. A. A.; Johari, M. R.; Kassim, A. H. M.

2016-07-01

Wastewater generated from carwash is one of the main wastewater resources, which contribute effectively in the increasing of environmental contamination due to the chemical characteristics of the car wastes. The present work aimed to develop an integrated treatment system for carwash wastewater based on coagulation and flocculation using Moringa oleifera and Ferrous Sulphate (FeSO4.7H2O) as well as natural filtration system. The carwash wastewater samples were collected from carwash station located at Parit Raja, Johor, Malaysia. The treatment system of car wash wastewater was designed in the lab scale in four stages included, aeration, coagulation and flocculation, sedimentation and filtration. The coagulation and flocculation unit was carried out using different dosage (35, 70, 105 and 140 mg L-1) of M. oleifera and FeSO4.7H2O, respectively. The efficiency of the integrated treatment system to treat carwash wastewater and to meet Environmental Quality Act (EQA 1974) was evaluated based on the analysis of pH, dissolved oxygen (DO), chemical oxygen demand (COD) and turbidity (NTU). The integrated treatment system was efficient for treatment of raw carwash wastewater. The treated carwash wastewaters meet EQA 1974 regulation 2009 (Standards A) in the term of pH and DO while, turbidity and COD reduced in the wastewater to meet Standards B. The integrated treatment system designed here with natural coagulant (M. oleifera) and filtration unit were effective for primary treatment of carwash wastewater before the final disposal or to be reused again for carwash process.

Suppurative processes

International Nuclear Information System (INIS)

Vinner, M.G.

1983-01-01

Suppurative process in the case of bronchiectatic disease, abscess and gang rene of lungs, has been described. Characteristic signs of roentgenologic pictu re of the above-mentioned diseases are considered. It is shown,that in most cas es roentgenologic studies give a possibility to make a high-quality diagnosis of suppurative processes

Investigating the Process of Process Modeling with Eye Movement Analysis

OpenAIRE

Pinggera, Jakob; Furtner, Marco; Martini, Markus; Sachse, Pierre; Reiter, Katharina; Zugal, Stefan; Weber, Barbara

2015-01-01

Research on quality issues of business process models has recently begun to explore the process of creating process models by analyzing the modeler's interactions with the modeling environment. In this paper we aim to complement previous insights on the modeler's modeling behavior with data gathered by tracking the modeler's eye movements when engaged in the act of modeling. We present preliminary results and outline directions for future research to triangulate toward a more comprehensive un...

Radiotracer investigations of the flotation process in copper ore processing

International Nuclear Information System (INIS)

Petryka, L.; Przewlocki, K.

1983-01-01

Optimization of copper ore processing requires in particular the investigation of the flotation process. 64 Cu induced in natural ore by activation was used as a tracer. Detailed measurements were performed in an industrial flotation plant consisting of 14 cells. As a result the mean residence time of different grain size fractions of natural copper sulphide was determined for all parts of the flotation plant together with the efficiency of the flotation process. (author)

Shot-noise-weighted processes : a new family of spatial point processes

NARCIS (Netherlands)

M.N.M. van Lieshout (Marie-Colette); I.S. Molchanov (Ilya)

1995-01-01

textabstractThe paper suggests a new family of of spatial point processes distributions. They are defined by means of densities with respect to the Poisson point process within a bounded set. These densities are given in terms of a functional of the shot-noise process with a given influence

Process Management Plans

Directory of Open Access Journals (Sweden)

Tomasz Miksa

2014-07-01

Full Text Available In the era of research infrastructures and big data, sophisticated data management practices are becoming essential building blocks of successful science. Most practices follow a data-centric approach, which does not take into account the processes that created, analysed and presented the data. This fact limits the possibilities for reliable verification of results. Furthermore, it does not guarantee the reuse of research, which is one of the key aspects of credible data-driven science. For that reason, we propose the introduction of the new concept of Process Management Plans, which focus on the identification, description, sharing and preservation of the entire scientific processes. They enable verification and later reuse of result data and processes of scientific experiments. In this paper we describe the structure and explain the novelty of Process Management Plans by showing in what way they complement existing Data Management Plans. We also highlight key differences, major advantages, as well as references to tools and solutions that can facilitate the introduction of Process Management Plans.

DECAB: process development of a phase change absorption process

NARCIS (Netherlands)

Sanchez Fernandez, E.; Goetheer, E.L.V.

2011-01-01

This work describes the conceptual design of a novel separation process for CO2 removal from flue gas based on precipitating solvents. The process here described (DECAB) is an enhanced CO2 absorption based on the Le Chatelier's principle, which states that reaction equilibrium can be shifted by

The H-Oil process: a worldwide leader in vacuum residue hydro processing

Energy Technology Data Exchange (ETDEWEB)

Colyar, J.J.; Wisdom, L.I.; Koskas, A.

1996-12-31

The h-Oil process is a catalytic hydrocracking process which is used to convert and upgrade petroleum residua and heavy oils. This paper discusses additional background information on the H-Oil process, some of the key advances made to the process and applications for the Latin America market. 5 refs., 6 tabs.., 2 figs.

Development of the Log-in Process and the Operation Process for the VHTR-SI Process Dynamic Simulation Code

International Nuclear Information System (INIS)

Chang, Jiwoon; Shin, Youngjoon; Kim, Jihwan; Lee, Kiyoung; Lee, Wonjae; Chang, Jonghwa; Youn, Cheung

2009-01-01

The VHTR-SI process is a hydrogen production technique by using Sulfur and Iodine. The SI process for a hydrogen production uses a high temperature (about 950 .deg. C) of the He gas which is a cooling material for an energy sources. The Korea Atomic Energy Research Institute Dynamic Simulation Code (KAERI DySCo) is an integration application software that simulates the dynamic behavior of the VHTR-SI process. A dynamic modeling is used to express and model the behavior of the software system over time. The dynamic modeling deals with the control flow of system, the interaction of objects and the order of actions in view of a time and transition by using a sequence diagram and a state transition diagram. In this paper, we present an user log-in process and an operation process for the KAERI DySCo by using a sequence diagram and a state transition diagram

Quantifying Quantum-Mechanical Processes.

Science.gov (United States)

Hsieh, Jen-Hsiang; Chen, Shih-Hsuan; Li, Che-Ming

2017-10-19

The act of describing how a physical process changes a system is the basis for understanding observed phenomena. For quantum-mechanical processes in particular, the affect of processes on quantum states profoundly advances our knowledge of the natural world, from understanding counter-intuitive concepts to the development of wholly quantum-mechanical technology. Here, we show that quantum-mechanical processes can be quantified using a generic classical-process model through which any classical strategies of mimicry can be ruled out. We demonstrate the success of this formalism using fundamental processes postulated in quantum mechanics, the dynamics of open quantum systems, quantum-information processing, the fusion of entangled photon pairs, and the energy transfer in a photosynthetic pigment-protein complex. Since our framework does not depend on any specifics of the states being processed, it reveals a new class of correlations in the hierarchy between entanglement and Einstein-Podolsky-Rosen steering and paves the way for the elaboration of a generic method for quantifying physical processes.

Hydrogen production processes

International Nuclear Information System (INIS)

2003-01-01

The goals of this first Gedepeon workshop on hydrogen production processes are: to stimulate the information exchange about research programs and research advances in the domain of hydrogen production processes, to indicate the domains of interest of these processes and the potentialities linked with the coupling of a nuclear reactor, to establish the actions of common interest for the CEA, the CNRS, and eventually EDF, that can be funded in the framework of the Gedepeon research group. This document gathers the slides of the 17 presentations given at this workshop and dealing with: the H 2 question and the international research programs (Lucchese P.); the CEA's research program (Lucchese P., Anzieu P.); processes based on the iodine/sulfur cycle: efficiency of a facility - flow-sheets, efficiencies, hard points (Borgard J.M.), R and D about the I/S cycle: Bunsen reaction (Colette S.), R and D about the I/S cycle: the HI/I 2 /H 2 O system (Doizi D.), demonstration loop/chemical engineering (Duhamet J.), materials and corrosion (Terlain A.); other processes under study: the Westinghouse cycle (Eysseric C.), other processes under study at the CEA (UT3, plasma,...) (Lemort F.), database about thermochemical cycles (Abanades S.), Zn/ZnO cycle (Broust F.), H 2 production by cracking, high temperature reforming with carbon trapping (Flamant G.), membrane technology (De Lamare J.); high-temperature electrolysis: SOFC used as electrolyzers (Grastien R.); generic aspects linked with hydrogen production: technical-economical evaluation of processes (Werkoff F.), thermodynamic tools (Neveu P.), the reactor-process coupling (Aujollet P.). (J.S.)

Materials, process, product analysis of coal process technology. Phase I final report

Energy Technology Data Exchange (ETDEWEB)

Saxton, J. C.; Roig, R. W.; Loridan, A.; Leggett, N. E.; Capell, R. G.; Humpstone, C. C.; Mudry, R. N.; Ayres, E.

1976-02-01

The purpose of materials-process-product analysis is a systematic evaluation of alternative manufacturing processes--in this case processes for converting coal into energy and material products that can supplement or replace petroleum-based products. The methodological steps in the analysis include: Definition of functional operations that enter into coal conversion processes, and modeling of alternative, competing methods to accomplish these functions; compilation of all feasible conversion processes that can be assembled from combinations of competing methods for the functional operations; systematic, iterative evaluation of all feasible conversion processes under a variety of economic situations, environmental constraints, and projected technological advances; and aggregative assessments (economic and environmental) of various industrial development scenarios. An integral part of the present project is additional development of the existing computer model to include: A data base for coal-related materials and coal conversion processes; and an algorithmic structure that facilitates the iterative, systematic evaluations in response to exogenously specified variables, such as tax policy, environmental limitations, and changes in process technology and costs. As an analytical tool, the analysis is intended to satisfy the needs of an analyst working at the process selection level, for example, with respect to the allocation of RDandD funds to competing technologies.

Process for separating nitrogen from methane using microchannel process technology

Science.gov (United States)

Tonkovich, Anna Lee [Marysville, OH; Qiu, Dongming [Dublin, OH; Dritz, Terence Andrew [Worthington, OH; Neagle, Paul [Westerville, OH; Litt, Robert Dwayne [Westerville, OH; Arora, Ravi [Dublin, OH; Lamont, Michael Jay [Hilliard, OH; Pagnotto, Kristina M [Cincinnati, OH

2007-07-31

The disclosed invention relates to a process for separating methane or nitrogen from a fluid mixture comprising methane and nitrogen, the process comprising: (A) flowing the fluid mixture into a microchannel separator, the microchannel separator comprising a plurality of process microchannels containing a sorption medium, the fluid mixture being maintained in the microchannel separator until at least part of the methane or nitrogen is sorbed by the sorption medium, and removing non-sorbed parts of the fluid mixture from the microchannel separator; and (B) desorbing the methane or nitrogen from the sorption medium and removing the desorbed methane or nitrogen from the microchannel separator. The process is suitable for upgrading methane from coal mines, landfills, and other sub-quality sources.

Business process reporting using process mining, analytic workflows and process cubes : A case study in education

NARCIS (Netherlands)

Bolt Iriondo, A.J.; de Leoni, M.; van der Aalst, W.M.P.; Gorissen, P.; Paolo, C.; Stefanie, R.-M.

2017-01-01

Business Process Intelligence (BPI) is an emerging topic that has gained popularity in the last decade. It is driven by the need for analysis techniques that allow businesses to understand and improve their processes. One of the most common applications of BPI is reporting, which consists on the

The plasma hearth process: Process residuals characterization

International Nuclear Information System (INIS)

Leatherman, G.L.; Geimer, R.; Batdorf, J.; Hassel, G.; Wolfe, P.; Carney, K.P.

1994-01-01

The Plasma Hearth Process (PHP) is a high-temperature waste treatment process being developed by Science Applications International Corporation (SAIC) for the Department of Energy (DOE) that destroys hazardous organics while stabilizing radionuclides and hazardous metals in a vitreous slag waste form. The PHP has potential application for the treatment of a wide range of mixed waste types in both the low-level and transuranic (TRU) mixed waste categories. DOE, through the Office of Technology Development's Mixed Waste Integrated Program (MWIP) is conducting a three phase development project to ready the PHP for implementation in the DOE complex

Process and device for processing radioactive wastes

International Nuclear Information System (INIS)

1974-01-01

A method is described for processing liquid radioactive wastes. It includes the heating of the liquid wastes so that the contained liquids are evaporated and a practically anhydrous mass of solid particles inferior in volume to that of the wastes introduced is formed, then the transformation of the solid particles into a monolithic structure. This transformation includes the compressing of the particles and sintering or fusion. The solidifying agent is a mixture of polyethylene and paraffin wax or a styrene copolymer and a polyester resin. The device used for processing the radioactive liquid wastes is also described [fr

Fermentation process using specific oxygen uptake rates as a process control

Science.gov (United States)

Van Hoek, Pim [Minnetonka, MN; Aristidou, Aristos [Maple Grove, MN; Rush, Brian [Minneapolis, MN

2011-05-10

Specific oxygen uptake (OUR) is used as a process control parameter in fermentation processes. OUR is determined during at least the production phase of a fermentation process, and process parameters are adjusted to maintain the OUR within desired ranges. The invention is particularly applicable when the fermentation is conducted using a microorganism having a natural PDC pathway that has been disrupted so that it no longer functions. Microorganisms of this sort often produce poorly under strictly anaerobic conditions. Microaeration controlled by monitoring OUR allows the performance of the microorganism to be optimized.

Photon technology. Laser processing technology; Photon technology. Laser process gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Survey has been conducted to develop laser processing technology utilizing the interaction between substance and photon. This is a part of the leading research on photon technology development. The photon technology development is aimed at novel technology development highly utilizing the quantum nature of photons. In the field of laser processing, high quality photons are used as tools, special functions of atoms and molecules will be discovered, and processing for functional fabrication (photon machining) will be established. A role of laser processing in industries has become significant, which is currently spreading not only into cutting and welding of materials and scalpels but also into such a special field as ultrafine processing of materials. The spreading is sometimes obstructed due to the difficulty of procurement of suitable machines and materials, and the increase of cost. The purpose of this study is to develop the optimal laser technology, to elucidate the interaction between substance and photon, and to develop the laser system and the transmission and regulation systems which realize the optimal conditions. 387 refs., 115 figs., 25 tabs.

Process Technical Basis Documentation Diagram for a solid-waste processing facility

International Nuclear Information System (INIS)

Benar, C.J.; Petersen, C.A.

1994-02-01

The Process Technical Basis Documentation Diagram is for a solid-waste processing facility that could be designed to treat, package, and certify contact-handled mixed low-level waste for permanent disposal. The treatment processes include stabilization using cementitious materials and immobilization using a polymer material. The Diagram identifies several engineering/demonstration activities that would confirm the process selection and process design. An independent peer review was conducted at the request of Westinghouse Hanford Company to determine the technical adequacy of the technical approach for waste form development. The peer review panel provided comments and identified documents that it felt were needed in the Diagram as precedence for Title I design. The Diagram is a visual tool to identify traceable documentation of key activities, including those documents suggested by the peer review, and to show how they relate to each other. The Diagram is divided into three sections: (1) the Facility section, which contains documents pertaining to the facility design, (2) the Process Demonstration section, which contains documents pertaining to the process engineering/demonstration work, and 3) the Regulatory section, which contains documents describing the compliance strategy for each acceptance requirement for each feed type, and how this strategy will be implemented

Flue Gas Desulphurization Processes

International Nuclear Information System (INIS)

Aly, A.I.M.; Halhouli, K.A.; Abu-Ashur, B.M.

1999-01-01

Flue gas desulphurization process are discussed. These processes can be grouped into non-regenerable systems and regenerable systems. The non-regenerable systems produce a product which is either disposed of as waste or sold as a by-product e.g. lime/limestone process. While in the regenerable systems, e.g. Wellman-Lord process, the SO 2 is regenerated from the sorbent(sodium sulphite), which is returned to absorb more SO 2 . Also a newer technology for flue gas desulphurization is discussed. The Ispra process uses bromine as oxidant, producing HBr, from which bromine is regenerated by electrolysis. The only by-products of this process are sulphuric acid and hydrogen, which are both valuable products, and no waste products are produced. Suggested modifications on the process are made based on experimental investigations to improve the efficiency of the process and to reduce its costs

BPMN process views construction

NARCIS (Netherlands)

Yongchareon, S.; Liu, Chengfei; Zhao, X.; Kowalkiewicz, M.; Kitagawa, H.; Ishikawa, Y.

2010-01-01

Process view technology is catching more attentions in modern business process management, as it enables the customisation of business process representation. This capability helps improve the privacy protection, authority control, flexible display, etc., in business process modelling. One of

Visual processing in rapid-chase systems: Image processing, attention, and awareness

Directory of Open Access Journals (Sweden)

Thomas eSchmidt

2011-07-01

Full Text Available Visual stimuli can be classified so rapidly that their analysis may be based on a single sweep of feedforward processing through the visuomotor system. Behavioral criteria for feedforward processing can be evaluated in response priming tasks where speeded pointing or keypress responses are performed towards target stimuli which are preceded by prime stimuli. We apply this method to several classes of complex stimuli. 1 When participants classify natural images into animals or non-animals, the time course of their pointing responses indicates that prime and target signals remain strictly sequential throughout all processing stages, meeting stringent behavioral criteria for feedforward processing (rapid-chase criteria. 2 Such priming effects are boosted by selective visual attention for positions, shapes, and colors, in a way consistent with bottom-up enhancement of visuomotor processing, even when primes cannot be consciously identified. 3 Speeded processing of phobic images is observed in participants specifically fearful of spiders or snakes, suggesting enhancement of feedforward processing by long-term perceptual learning. 4 When the perceived brightness of primes in complex displays is altered by means of illumination or transparency illusions, priming effects in speeded keypress responses can systematically contradict subjective brightness judgments, such that one prime appears brighter than the other but activates motor responses as if it was darker. We propose that response priming captures the output of the first feedforward pass of visual signals through the visuomotor system, and that this output lacks some characteristic features of more elaborate, recurrent processing. This way, visuomotor measures may become dissociated from several aspects of conscious vision. We argue that "fast" visuomotor measures predominantly driven by feedforward processing should supplement "slow" psychophysical measures predominantly based on visual

A survey of process control computers at the Idaho Chemical Processing Plant

International Nuclear Information System (INIS)

Dahl, C.A.

1989-01-01

The Idaho Chemical Processing Plant (ICPP) at the Idaho National Engineering Laboratory is charged with the safe processing of spent nuclear fuel elements for the United States Department of Energy. The ICPP was originally constructed in the late 1950s and used state-of-the-art technology for process control at that time. The state of process control instrumentation at the ICPP has steadily improved to keep pace with emerging technology. Today, the ICPP is a college of emerging computer technology in process control with some systems as simple as standalone measurement computers while others are state-of-the-art distributed control systems controlling the operations in an entire facility within the plant. The ICPP has made maximal use of process computer technology aimed at increasing surety, safety, and efficiency of the process operations. Many benefits have been derived from the use of the computers for minimal costs, including decreased misoperations in the facility, and more benefits are expected in the future

Process evaluation distributed system

Science.gov (United States)

Moffatt, Christopher L. (Inventor)

2006-01-01

The distributed system includes a database server, an administration module, a process evaluation module, and a data display module. The administration module is in communication with the database server for providing observation criteria information to the database server. The process evaluation module is in communication with the database server for obtaining the observation criteria information from the database server and collecting process data based on the observation criteria information. The process evaluation module utilizes a personal digital assistant (PDA). A data display module in communication with the database server, including a website for viewing collected process data in a desired metrics form, the data display module also for providing desired editing and modification of the collected process data. The connectivity established by the database server to the administration module, the process evaluation module, and the data display module, minimizes the requirement for manual input of the collected process data.

Development of processes for the utilization of Brazilian coal using nuclear process heat and/or nuclear process steam

International Nuclear Information System (INIS)

Bamert, H.; Niessen, H.F.; Walbeck, M.; Wasrzik, U.; Mueller, R.; Schiffers, U.; Strauss, W.

1980-01-01

Status of the project: End of the project definition phase and preparation of the planned conceptual phase. Objective of the project: Development of processes for the utilization of nuclear process heat and/or nuclear process steam for the gasification of coal with high ash content, in particular coal from Brazil. Results: With the data of Brazilian coal of high ash content (mine Leao/ 43% ash in the mine-mouth quality, 20% ash after preparation) there have been worked out proposals for the mine planning and for a number of processes. On the basis of these proposals and under consideration of the main data specified by the Brazilian working group there have been choosen two processes and worked out in a conceptual design: 1) pressurized water reactor + LURGI-pressure gasifier/hydrogasification for the production of SNG and 2) high temperature reactor steam gasification for the production of town gas. The economic evaluation showed that the two processes are not substantially different in their cost efficiency and they are economical on a long-term basis. For more specific design work there has been planned the implementation of an experimental programme using the semi-technical plants 'hydrogasification' in Wesseling and 'steam gasification' in Essen as the conceptual phase. (orig.) [de

Improving the Document Development Process: Integrating Relational Data and Statistical Process Control.

Science.gov (United States)

Miller, John

1994-01-01

Presents an approach to document numbering, document titling, and process measurement which, when used with fundamental techniques of statistical process control, reveals meaningful process-element variation as well as nominal productivity models. (SR)

Fuel processing. Wastes processing

International Nuclear Information System (INIS)

Bourgeois, M.

2000-01-01

The gaseous, liquid and solid radioactive effluents generated by the fuel reprocessing, can't be release in the environment. They have to be treated in order to respect the limits of the pollution regulations. These processing are detailed and discussed in this technical paper. A second part is devoted to the SPIN research program relative to the separation of the long life radionuclides in order to reduce the radioactive wastes storage volume. (A.L.B.)

Exploring processes and deviations

NARCIS (Netherlands)

Leemans, S.J.J.; Fahland, D.; Aalst, van der W.M.P.; Fournier, F.; Mendling, J.

2015-01-01

In process mining, one of the main challenges is to discover a process model, while balancing several quality criteria. This often requires repeatedly setting parameters, discovering a map and evaluating it, which we refer to as process exploration. Commercial process mining tools like Disco,

Process for winning uranium from wet process phosphoric acid

International Nuclear Information System (INIS)

1980-01-01

A process is described for winning uranium from wet process phosphoric acid by means of liquid-liquid extraction with organic phosphoric acid esters. The process is optimised by keeping the sulphate percentage in the phosphoric acid below 2% by weight, and preferably below 0.6% by weight, as compared to P 2 O 5 in the phosphoric acid. This is achieved by adding an excess of Ba and/or Ca carbonate or sulfide solution and filtering off the formed calcium and/or barium sulphate precipitates. Solid KClO 3 is then added to the filtrate to oxidise U 4+ to U 6+ . The normal extraction procedure using organic phosphoric esters as extraction liquid, can then be applied. (Th.P.)

Product- and Process Units in the CRITT Translation Process Research Database

DEFF Research Database (Denmark)

Carl, Michael

than 300 hours of text production. The database provides the raw logging data, as well as Tables of pre-processed product- and processing units. The TPR-DB includes various types of simple and composed product and process units that are intended to support the analysis and modelling of human text......The first version of the "Translation Process Research Database" (TPR DB v1.0) was released In August 2012, containing logging data of more than 400 translation and text production sessions. The current version of the TPR DB, (v1.4), contains data from more than 940 sessions, which represents more...

Poisson branching point processes

International Nuclear Information System (INIS)

Matsuo, K.; Teich, M.C.; Saleh, B.E.A.

1984-01-01

We investigate the statistical properties of a special branching point process. The initial process is assumed to be a homogeneous Poisson point process (HPP). The initiating events at each branching stage are carried forward to the following stage. In addition, each initiating event independently contributes a nonstationary Poisson point process (whose rate is a specified function) located at that point. The additional contributions from all points of a given stage constitute a doubly stochastic Poisson point process (DSPP) whose rate is a filtered version of the initiating point process at that stage. The process studied is a generalization of a Poisson branching process in which random time delays are permitted in the generation of events. Particular attention is given to the limit in which the number of branching stages is infinite while the average number of added events per event of the previous stage is infinitesimal. In the special case when the branching is instantaneous this limit of continuous branching corresponds to the well-known Yule--Furry process with an initial Poisson population. The Poisson branching point process provides a useful description for many problems in various scientific disciplines, such as the behavior of electron multipliers, neutron chain reactions, and cosmic ray showers

Investigation of Mediational Processes Using Parallel Process Latent Growth Curve Modeling

Science.gov (United States)

Cheong, JeeWon; MacKinnon, David P.; Khoo, Siek Toon

2010-01-01

This study investigated a method to evaluate mediational processes using latent growth curve modeling. The mediator and the outcome measured across multiple time points were viewed as 2 separate parallel processes. The mediational process was defined as the independent variable influencing the growth of the mediator, which, in turn, affected the growth of the outcome. To illustrate modeling procedures, empirical data from a longitudinal drug prevention program, Adolescents Training and Learning to Avoid Steroids, were used. The program effects on the growth of the mediator and the growth of the outcome were examined first in a 2-group structural equation model. The mediational process was then modeled and tested in a parallel process latent growth curve model by relating the prevention program condition, the growth rate factor of the mediator, and the growth rate factor of the outcome. PMID:20157639

A Campbell random process

International Nuclear Information System (INIS)

Reuss, J.D.; Misguich, J.H.

1993-02-01

The Campbell process is a stationary random process which can have various correlation functions, according to the choice of an elementary response function. The statistical properties of this process are presented. A numerical algorithm and a subroutine for generating such a process is built up and tested, for the physically interesting case of a Campbell process with Gaussian correlations. The (non-Gaussian) probability distribution appears to be similar to the Gamma distribution

Weak convergence of marked point processes generated by crossings of multivariate jump processes

DEFF Research Database (Denmark)

Tamborrino, Massimiliano; Sacerdote, Laura; Jacobsen, Martin

2014-01-01

We consider the multivariate point process determined by the crossing times of the components of a multivariate jump process through a multivariate boundary, assuming to reset each component to an initial value after its boundary crossing. We prove that this point process converges weakly...... process converging to a multivariate Ornstein–Uhlenbeck process is discussed as a guideline for applying diffusion limits for jump processes. We apply our theoretical findings to neural network modeling. The proposed model gives a mathematical foundation to the generalization of the class of Leaky...

Business process quality management

NARCIS (Netherlands)

Reijers, H.A.; Mendling, J.; Recker, J.; Brocke, vom J.; Rosemann, M.

2010-01-01

Abstract Process modeling is a central element in any approach to Business Process Management (BPM). However, what hinders both practitioners and aca demics is the lack of support for assessing the quality of process models — let alone realizing high quality process models. Existing frameworks are

Distributed genetic process mining

NARCIS (Netherlands)

Bratosin, C.C.; Sidorova, N.; Aalst, van der W.M.P.

2010-01-01

Process mining aims at discovering process models from data logs in order to offer insight into the real use of information systems. Most of the existing process mining algorithms fail to discover complex constructs or have problems dealing with noise and infrequent behavior. The genetic process

7 Processes that Enable NASA Software Engineering Technologies: Value-Added Process Engineering

Science.gov (United States)

Housch, Helen; Godfrey, Sally

2011-01-01

The presentation reviews Agency process requirements and the purpose, benefits, and experiences or seven software engineering processes. The processes include: product integration, configuration management, verification, software assurance, measurement and analysis, requirements management, and planning and monitoring.

Motivated information processing and group decision-making : Effects of process accountability on information processing and decision quality

NARCIS (Netherlands)

Scholten, Lotte; van Knippenberg, Daan; Nijstad, Bernard A.; De Dreu, Carsten K. W.

Integrating dual-process models [Chaiken, S., & Trope, Y. (Eds.). (1999). Dual-process theories in social psychology. NewYork: Guilford Press] with work on information sharing and group decision-making [Stasser, G., & Titus, W. (1985). Pooling of unshared information in group decision making: biased

FFTF gas processing systems

International Nuclear Information System (INIS)

Halverson, T.G.

1977-01-01

The design and operation of the two radioactive gas processing systems at the Fast Flux Test Facility (FFTF) exemplifies the concept that will be used in the first generation of Liquid Metal Fast Breeder Reactors (LMFBR's). The two systems, the Radioactive Argon Processing System (RAPS) and the Cell Atmosphere Processing System (CAPS), process the argon and nitrogen used in the FFTF for cover gas on liquid metal systems and as inert atmospheres in steel lined cells housing sodium equipment. The RAPS specifically processes the argon cover gas from the reactor coolant system, providing for decontamination and eventual reuse. The CAPS processes radioactive gasses from inerted cells and other liquid metal cover gas systems, providing for decontamination and ultimate discharge to the atmosphere. The cryogenic processing of waste gas by both systems is described

Sustainable Process Synthesis-Intensification

DEFF Research Database (Denmark)

Babi, Deenesh Kavi; Holtbruegge, Johannes; Lutze, Philip

2014-01-01

Sustainable process design can be achieved by performing process synthesis and process intensification together. This approach first defines a design target through a sustainability analysis and then finds design alternatives that match the target through process intensification. A systematic......, multi-stage framework for process synthesis- intensification that identifies more sustainable process designs has been developed. At stages 1-2, the working scale is at the level of unit operations, where a base case design is identified and analyzed with respect to sustainability metrics. At stages 3......, a phenomena-based process synthesis method is applied, where the phenomena involved in each tasks are identified, manipulated and recombined to generate new and/or existing unit operations configured into flowsheets that are more sustainable from those found in the previous levels. An overview of the key...

Feller processes: the next generation in modeling. Brownian motion, Lévy processes and beyond.

Directory of Open Access Journals (Sweden)

Björn Böttcher

Full Text Available We present a simple construction method for Feller processes and a framework for the generation of sample paths of Feller processes. The construction is based on state space dependent mixing of Lévy processes. Brownian Motion is one of the most frequently used continuous time Markov processes in applications. In recent years also Lévy processes, of which Brownian Motion is a special case, have become increasingly popular. Lévy processes are spatially homogeneous, but empirical data often suggest the use of spatially inhomogeneous processes. Thus it seems necessary to go to the next level of generalization: Feller processes. These include Lévy processes and in particular brownian motion as special cases but allow spatial inhomogeneities. Many properties of Feller processes are known, but proving the very existence is, in general, very technical. Moreover, an applicable framework for the generation of sample paths of a Feller process was missing. We explain, with practitioners in mind, how to overcome both of these obstacles. In particular our simulation technique allows to apply Monte Carlo methods to Feller processes.

Standard Model processes

CERN Document Server

Mangano, M.L.; Aguilar-Saavedra, Juan Antonio; Alekhin, S.; Badger, S.; Bauer, C.W.; Becher, T.; Bertone, V.; Bonvini, M.; Boselli, S.; Bothmann, E.; Boughezal, R.; Cacciari, M.; Carloni Calame, C.M.; Caola, F.; Campbell, J.M.; Carrazza, S.; Chiesa, M.; Cieri, L.; Cimaglia, F.; Febres Cordero, F.; Ferrarese, P.; D'Enterria, D.; Ferrera, G.; Garcia i Tormo, X.; Garzelli, M.V.; Germann, E.; Hirschi, V.; Han, T.; Ita, H.; Jäger, B.; Kallweit, S.; Karlberg, A.; Kuttimalai, S.; Krauss, F.; Larkoski, A.J.; Lindert, J.; Luisoni, G.; Maierhöfer, P.; Mattelaer, O.; Martinez, H.; Moch, S.; Montagna, G.; Moretti, M.; Nason, P.; Nicrosini, O.; Oleari, C.; Pagani, D.; Papaefstathiou, A.; Petriello, F.; Piccinini, F.; Pierini, M.; Pierog, T.; Pozzorini, S.; Re, E.; Robens, T.; Rojo, J.; Ruiz, R.; Sakurai, K.; Salam, G.P.; Salfelder, L.; Schönherr, M.; Schulze, M.; Schumann, S.; Selvaggi, M.; Shivaji, A.; Siodmok, A.; Skands, P.; Torrielli, P.; Tramontano, F.; Tsinikos, I.; Tweedie, B.; Vicini, A.; Westhoff, S.; Zaro, M.; Zeppenfeld, D.; CERN. Geneva. ATS Department

2017-06-22

This report summarises the properties of Standard Model processes at the 100 TeV pp collider. We document the production rates and typical distributions for a number of benchmark Standard Model processes, and discuss new dynamical phenomena arising at the highest energies available at this collider. We discuss the intrinsic physics interest in the measurement of these Standard Model processes, as well as their role as backgrounds for New Physics searches.

Classical higher-order processes

DEFF Research Database (Denmark)

Montesi, Fabrizio

2017-01-01

Classical Processes (CP) is a calculus where the proof theory of classical linear logic types processes à la Π-calculus, building on a Curry-Howard correspondence between session types and linear propositions. We contribute to this research line by extending CP with process mobility, inspired...... by the Higher-Order Π-calculus. The key to our calculus is that sequents are asymmetric: one side types sessions as in CP and the other types process variables, which can be instantiated with process values. The controlled interaction between the two sides ensures that process variables can be used at will......, but always respecting the linear usage of sessions expected by the environment....

Process margin enhancement for 0.25-μm metal etch process

Science.gov (United States)

Lee, Chung Y.; Ma, Wei Wen; Lim, Eng H.; Cheng, Alex T.; Joy, Raymond; Ross, Matthew F.; Wong, Selmer S.; Marlowe, Trey

2000-06-01

This study evaluates electron beam stabilization of UV6, a positive tone Deep-UV (DUV) resist from Shipley, for a 0.25 micrometer metal etch application. Results are compared between untreated resist and resist treated with different levels of electron beam stabilization. The electron beam processing was carried out in an ElectronCureTM flood electron beam exposure system from Honeywell International Inc., Electron Vision. The ElectronCureTM system utilizes a flood electron beam source which is larger in diameter than the substrate being processed, and is capable of variable energy so that the electron range is matched to the resist film thickness. Changes in the UV6 resist material as a result of the electron beam stabilization are monitored via spectroscopic ellipsometry for film thickness and index of refraction changes and FTIR for analysis of chemical changes. Thermal flow stability is evaluated by applying hot plate bakes of 150 degrees Celsius and 200 degrees Celsius, to patterned resist wafers with no treatment and with an electron beam dose level of 2000 (mu) C/cm2. A significant improvement in the thermal flow stability of the patterned UV6 resist features is achieved with the electron beam stabilization process. Etch process performance of the UV6 resist was evaluated by performing a metal pattern transfer process on wafers with untreated resist and comparing these with etch results on wafers with different levels of electron beam stabilization. The etch processing was carried out in an Applied Materials reactor with an etch chemistry including BCl3 and Cl2. All wafers were etched under the same conditions and the resist was treated after etch to prevent further erosion after etch but before SEM analysis. Post metal etch SEM cross-sections show the enhancement in etch resistance provided by the electron beam stabilization process. Enhanced process margin is achieved as a result of the improved etch resistance, and is observed in reduced resist side

Quality Control in Automated Manufacturing Processes – Combined Features for Image Processing

Directory of Open Access Journals (Sweden)

B. Kuhlenkötter

2006-01-01

Full Text Available In production processes the use of image processing systems is widespread. Hardware solutions and cameras respectively are available for nearly every application. One important challenge of image processing systems is the development and selection of appropriate algorithms and software solutions in order to realise ambitious quality control for production processes. This article characterises the development of innovative software by combining features for an automatic defect classification on product surfaces. The artificial intelligent method Support Vector Machine (SVM is used to execute the classification task according to the combined features. This software is one crucial element for the automation of a manually operated production process. 

The creation of process redesigns by selecting, transforming and replacing process parts

NARCIS (Netherlands)

Netjes, M.; Reijers, H.A.; Aalst, van der W.M.P.

2008-01-01

For companies to sustain competitive advantages, it is required to redesign and improve business processes continuously by monitoring and analyzing process enactment results. Furthermore, organizational structures must be redesigned according to the changes in business processes. However, there are

Hierarchical process memory: memory as an integral component of information processing

Science.gov (United States)

Hasson, Uri; Chen, Janice; Honey, Christopher J.

2015-01-01

Models of working memory commonly focus on how information is encoded into and retrieved from storage at specific moments. However, in the majority of real-life processes, past information is used continuously to process incoming information across multiple timescales. Considering single unit, electrocorticography, and functional imaging data, we argue that (i) virtually all cortical circuits can accumulate information over time, and (ii) the timescales of accumulation vary hierarchically, from early sensory areas with short processing timescales (tens to hundreds of milliseconds) to higher-order areas with long processing timescales (many seconds to minutes). In this hierarchical systems perspective, memory is not restricted to a few localized stores, but is intrinsic to information processing that unfolds throughout the brain on multiple timescales. “The present contains nothing more than the past, and what is found in the effect was already in the cause.”Henri L Bergson PMID:25980649

Experimental study on heat pipe assisted heat exchanger used for industrial waste heat recovery

International Nuclear Information System (INIS)

Ma, Hongting; Yin, Lihui; Shen, Xiaopeng; Lu, Wenqian; Sun, Yuexia; Zhang, Yufeng; Deng, Na

2016-01-01

Highlights: • A heat pipe heat exchanger (HPHE) was used to recycle the waste heat in a slag cooling process of steel industry. • An specially designed on-line cleaning device was construed and used to enhance the heat transfer of HPHE. • The performance characteristics of a HPHE has been assessed by integrating the first and second law of thermodynamics. • The optimum operation conditions was determined by integrating the first and the second law of thermodynamics. - Abstract: Steel industry plays an important role economically in China. A great amount of hot waste liquids and gases are discharged into environment during many steelmaking processes. These waste liquids and gases have crucial energy saving potential, especially for steel slag cooling process. It could be possible to provide energy saving by employing a waste heat recovery system (WHRS). The optimum operation condition was assessed by integrating the first and the second law of thermodynamics for a water–water heat pipe heat exchanger (HPHE) for a slag cooling process in steel industry. The performance characteristics of a HPHE has been investigated experimentally by analyzing heat transfer rate, heat transfer coefficient, effectiveness, exergy efficiency and number of heat transfer units (NTU). A specially designed on-line cleaning device was used to clean the heat exchange tubes and enhance heat transfer. The results indicated that the exergy efficiency increased with the increment of waste water mass flow rate at constant fresh water mass flow rate, while the effectiveness decreased at the same operation condition. As the waste water mass flow rate varied from 0.83 m"3/h to 1.87 m"3/h, the effectiveness and exergy efficiency varied from 0.19 to 0.09 and from 34% to 41%, respectively. In the present work, the optimal flow rates of waste water and fresh water were 1.20 m"3/h and 3.00 m"3/h, respectively. The on-line cleaning device had an obvious effect on the heat transfer, by performing

Process mining applied to the test process of wafer steppers in ASML

NARCIS (Netherlands)

Rozinat, A.; Jong, de I.S.M.; Günther, C.W.; Aalst, van der W.M.P.

2009-01-01

Process mining techniques attempt to extract nontrivial and useful information from event logs. For example, there are many process mining techniques to automatically discover a process model describing the causal dependencies between activities. Several successful case studies have been reported in

Welding process

International Nuclear Information System (INIS)

Abdul Nassir Ibrahim; Azali Muhammad; Ab. Razak Hamzah; Abd. Aziz Mohamed; Mohamad Pauzi Ismail

2008-01-01

For the final chapter of this book, there is basic introduction on welding process. The good radiography must know somehow on welding process so that they can know what kind of welding that must rejected or not. All of the exposure technique that mention in earlier chapter almost applicable in this field because welding process is critical problem if there is no inspection will be done. So, for this chapter, all the discontinuity that usually appeared will be discussed and there is another discontinuity maybe not to important and do not give big impact if found it, do not described here. On top of that, the decision to accept or reject based on code, standard and specification that agreed by both to make sure that decision that agreed is corrected and more meaningful.

Multivariate supOU processes

DEFF Research Database (Denmark)

Barndorff-Nielsen, Ole Eiler; Stelzer, Robert

Univariate superpositions of Ornstein-Uhlenbeck (OU) type processes, called supOU processes, provide a class of continuous time processes capable of exhibiting long memory behaviour. This paper introduces multivariate supOU processes and gives conditions for their existence and finiteness...... of moments. Moreover, the second order moment structure is explicitly calculated, and examples exhibit the possibility of long range dependence. Our supOU processes are defined via homogeneous and factorisable Lévy bases. We show that the behaviour of supOU processes is particularly nice when the mean...... reversion parameter is restricted to normal matrices and especially to strictly negative definite ones.For finite variation Lévy bases we are able to give conditions for supOU processes to have locally bounded càdlàg paths of finite variation and to show an analogue of the stochastic differential equation...

Multivariate supOU processes

DEFF Research Database (Denmark)

Barndorff-Nielsen, Ole Eiler; Stelzer, Robert

2011-01-01

Univariate superpositions of Ornstein–Uhlenbeck-type processes (OU), called supOU processes, provide a class of continuous time processes capable of exhibiting long memory behavior. This paper introduces multivariate supOU processes and gives conditions for their existence and finiteness of moments....... Moreover, the second-order moment structure is explicitly calculated, and examples exhibit the possibility of long-range dependence. Our supOU processes are defined via homogeneous and factorizable Lévy bases. We show that the behavior of supOU processes is particularly nice when the mean reversion...... parameter is restricted to normal matrices and especially to strictly negative definite ones. For finite variation Lévy bases we are able to give conditions for supOU processes to have locally bounded càdlàg paths of finite variation and to show an analogue of the stochastic differential equation of OU...

Rapid process development of chromatographic process using direct analysis in real time mass spectrometry as a process analytical technology tool.

Science.gov (United States)

Yan, Binjun; Chen, Teng; Xu, Zhilin; Qu, Haibin

2014-06-01

The concept of quality by design (QbD) is widely applied in the process development of pharmaceuticals. However, the additional cost and time have caused some resistance about QbD implementation. To show a possible solution, this work proposed a rapid process development method, which used direct analysis in real time mass spectrometry (DART-MS) as a process analytical technology (PAT) tool for studying the chromatographic process of Ginkgo biloba L., as an example. The breakthrough curves were fast determined by DART-MS at-line. A high correlation coefficient of 0.9520 was found between the concentrations of ginkgolide A determined by DART-MS and HPLC. Based on the PAT tool, the impacts of process parameters on the adsorption capacity were discovered rapidly, which showed a decreased adsorption capacity with the increase of the flow rate. This work has shown the feasibility and advantages of integrating PAT into QbD implementation for rapid process development. Copyright © 2014 Elsevier B.V. All rights reserved.