Normal Incidence for Graded Index Surfaces

Science.gov (United States)

Khankhoje, Uday K.; Van Zyl, Jakob

2011-01-01

A plane wave is incident normally from vacuum (eta(sub 0) = 1) onto a smooth surface. The substrate has three layers; the top most layer has thickness d(sub 1) and permittivity epsilon(sub 1). The corresponding numbers for the next layer are d(sub 2); epsilon(sub 2), while the third layer which is semi-in nite has index eta(sub 3). The Hallikainen model [1] is used to relate volumetric soil moisture to the permittivity. Here, we consider the relation for the real part of the permittivity for a typical loam soil: acute epsilon(mv) = 2.8571 + 3.9678 x mv + 118:85 x mv(sup 2).

Normal velocity freeze-out of the Richtmyer-Meshkov instability when a rarefaction is reflected

Science.gov (United States)

Wouchuk, J. G.; Sano, T.

2015-02-01

The Richtmyer-Meshkov instability (RMI) develops when a shock front hits a rippled contact surface separating two different fluids. After the incident shock refraction, a transmitted shock is always formed and another shock or a rarefaction is reflected back. The pressure-entropy-vorticity fields generated by the rippled wave fronts are responsible for the generation of hydrodynamic perturbations in both fluids. In linear theory, the contact surface ripple reaches an asymptotic normal velocity which is dependent on the incident shock Mach number, fluids density ratio, and compressibilities. It was speculated in the past about the possibility of getting a zero value for the asymptotic normal velocity, a phenomenon that was called "freeze-out" [G. Fraley, Phys. Fluids 29, 376 (1986), 10.1063/1.865722; K. Mikaelian, Phys. Fluids 6, 356 (1994), 10.1063/1.868091, A. L. Velikovich et al., Phys. Plasmas 8, 592 (2001), 10.1063/1.1335829]. In a previous paper, freeze-out was studied for the case when a shock is reflected at the contact surface [J. G. Wouchuk and K. Nishihara, Phys. Rev. E 70, 026305 (2004), 10.1103/PhysRevE.70.026305]. In this work the freeze-out of the RMI is studied for the case in which a rarefaction is reflected back. Two different regimes are found: nearly equal preshock densities at the interface at any shock intensity, and very large density difference for strong shocks. The contour curves that relate shock Mach number and preshock density ratio are obtained in both regimes for fluids with equal and different compressibilities. An analysis of the temporal evolution of different cases of freeze-out is shown. It is seen that the freeze-out is the result of the interaction between the unstable interface and the rippled wave fronts. As a general and qualitative criterion to look for freeze-out situations, it is seen that a necessary condition for freeze-out is the same orientation for the tangential velocities generated at each side of the contact

High-accuracy measurements of the normal specular reflectance

International Nuclear Information System (INIS)

Voarino, Philippe; Piombini, Herve; Sabary, Frederic; Marteau, Daniel; Dubard, Jimmy; Hameury, Jacques; Filtz, Jean Remy

2008-01-01

The French Laser Megajoule (LMJ) is designed and constructed by the French Commissariata l'Energie Atomique (CEA). Its amplifying section needs highly reflective multilayer mirrors for the flash lamps. To monitor and improve the coating process, the reflectors have to be characterized to high accuracy. The described spectrophotometer is designed to measure normal specular reflectance with high repeatability by using a small spot size of 100 μm. Results are compared with ellipsometric measurements. The instrument can also perform spatial characterization to detect coating nonuniformity

Exploring reflective 'critical incident' documentation of professionalism lapses in a medical undergraduate setting

Directory of Open Access Journals (Sweden)

McLachlan John C

2009-07-01

Full Text Available Abstract Background Measuring professionalism in undergraduate medical students is a difficult process, and no one method has currently emerged as the definitive means of assessment in this field. Student skills in reflection have been shown to be highly important in the development of professional behaviours. By studying student reflections on lapses in professional judgement, recorded as 'critical incidents', it is possible to explore themes which are significant for the development of professional behaviour in an undergraduate setting. Methods We examined critical incident reporting combined with optional written student reflection as a method for exploring professionalism in undergraduate medical students. 228 students split between Year 1 and 2 of one academic year of undergraduate medicine were studied retrospectively and a grounded theory approach to analysis was employed. Results This year generated 16 critical incident reports and corresponding student reflections, all of which were considered. In addition to identifying the nature of the critical incidents, 3 principal themes emerged. These were the impact and consequences of the report having been made, student reactions to the events (both positive and negative, and student responses regarding future actions. Conclusion This study indicates that unprofessional behaviour can be identified and challenged by both the faculty and the students involved, and suggests that positive behavioural changes might be made with the aim of preventing future occurrences. We provide a low cost approach of measuring and recording professional behaviour.

[Idiopathic normal pressure hydrocephalus: High incidence in people over 80 years of age].

Science.gov (United States)

Aragonès, Josep Maria; Altimiras, Jacint; Alonso, Francisco; Roura, Pere; Alfonso, Sebastián; Bajo, Lorena

Idiopathic normal pressure hydrocephalus is usually observed in adults over 60 years of age. The highest incidence of cases is between 70 and 80 years-old, and it could be under-diagnosed in over 80 year-olds. A description is presented on the overall incidence and age group incidence, the delay in the diagnosis, and main outcomes. A descriptive study was performed on patients with idiopathic normal pressure hydrocephalus, in the population of Osona County during the years 2010-2015. The annual incidence rate was 4.43 per 100,000 inhabitants. The incidence increased with age; from 8.09 per 100,000 in the 60 to 69 years age group, to 23.61 per 100,000 in the 70-79 years age group of, and to 37.02 per 100,000 in the 80-89 years age. The delay in the diagnosis was 15.01 ± 10.35 months. All the patients improved after surgery, but only 73.3% of the patients maintained the improvement after one year. Idiopathic normal pressure hydrocephalus is an age related disease and probably underdiagnosed in the elderly. An early diagnosis and a clinical suspicion are essential in patients over 80 years old. Copyright © 2017 SEGG. Publicado por Elsevier España, S.L.U. All rights reserved.

Higher levels of albuminuria within the normal range predict incident hypertension.

Science.gov (United States)

Forman, John P; Fisher, Naomi D L; Schopick, Emily L; Curhan, Gary C

2008-10-01

Higher levels of albumin excretion within the normal range are associated with cardiovascular disease in high-risk individuals. Whether incremental increases in urinary albumin excretion, even within the normal range, are associated with the development of hypertension in low-risk individuals is unknown. This study included 1065 postmenopausal women from the first Nurses' Health Study and 1114 premenopausal women from the second Nurses' Health Study who had an albumin/creatinine ratio who did not have diabetes or hypertension. Among the older women, 271 incident cases of hypertension occurred during 4 yr of follow-up, and among the younger women, 296 incident cases of hypertension occurred during 8 yr of follow-up. Cox proportional hazards regression was used to examine prospectively the association between the albumin/creatinine ratio and incident hypertension after adjustment for age, body mass index, estimated GFR, baseline BP, physical activity, smoking, and family history of hypertension. Participants who had an albumin/creatinine ratio in the highest quartile (4.34 to 24.17 mg/g for older women and 3.68 to 23.84 mg/g for younger women) were more likely to develop hypertension than those who had an albumin/creatinine ratio in the lowest quartile (hazard ratio 1.76 [95% confidence interval 1.21 to 2.56] and hazard ratio 1.35 [95% confidence interval 0.97 to 1.91] for older and younger women, respectively). Higher albumin/creatinine ratios, even within the normal range, are independently associated with increased risk for development of hypertension among women without diabetes. The definition of normal albumin excretion should be reevaluated.

Gradient metasurface for four-direction anomalous reflection in terahertz

Science.gov (United States)

Wang, Jiao; Jiang, Yannan

2018-06-01

In this paper, a four-direction anomalous reflection metasurface is proposed. The basic cells comprise of squares and circles, which are designed at various sizes and arranged in a super cell at regular spacing. Then, properly combining super cells molds a square phase gradient metasurface (PGM). It is mounted on an optical thickness gold mirror, which inhibits all light transmission. Markedly different from previously reported metasurfaces, the square PGM is characterized by four-direction reflection beams. It takes into consideration the normal incidence and the oblique incidence. For the normal incidence, that the degrees of the four reflection angles are identical is due to the x, - x, y and - y directional discontinuous phase gradients, and lies on the symmetric structure in the xoy plane, which is then revealed by the surface current distribution. Incident angles varying from -20° to 20°, the reflection angles are demonstrated in the oblique incidence. Moreover, the PGM is polarization-independent. The performance is attributed to the symmetry of structure, which is verified by Radar cross section. Simulated results prove that our method offers a simple and effective strategy for metasurface design in terahertz. The proposed PGM can aid in focused beams, steering beams, and shaped beams.

Diffractive optical element-based glossmeter for the on-line measurement of normal reflectance on a printed porous coated paper

Science.gov (United States)

Oksman, Antti; Kuivalainen, Kalle; Ta˚G, Carl-Mikael; Juuti, Mikko; Mattila, Rauno; Hietala, Eero; Gane, Patrick A. C.; Peiponen, Kai-Erik

2011-04-01

Gloss of a product, such as print gloss, is mainly inspected with conventional white light glossmeters both at laboratory or production facilities. However, problems occur in conventional gloss measurement when the inspected surface is vertically moved in the plane of incidence and reflection or when the measurement area is small or curved. For a partial solution to these problems, we have previously introduced diffractive optical element-based glossmeters (DOGs) for the gloss inspection in laboratories and off-line use. We present a new construction of DOG, termed μDOG 1D, for the one-dimensional on-line print gloss measurement, in the form of the reflectance determination normal to the surface. The function of the glossmeter is demonstrated by laboratory tests and on-line measurements at a heat-set web offset printing machine. It is shown that gloss (i.e., normal reflectance) and minute gloss variation of papers and prints can be measured at the printing line using the glossmeter. This glossmeter is expected to be useful in real-time monitoring of the gloss and surface-specific absorption not only in the printing industry but also in inspection of products in other industrial sectors, such as metal finishing, laminating, paper, and construction materials manufacturing.

Light trapping for emission from a photovoltaic cell under normally incident monochromatic illumination

Energy Technology Data Exchange (ETDEWEB)

Takeda, Yasuhiko, E-mail: takeda@mosk.tytlabs.co.jp; Iizuka, Hideo; Mizuno, Shintaro; Hasegawa, Kazuo; Ichikawa, Tadashi; Ito, Hiroshi; Kajino, Tsutomu [Toyota Central Research and Development Laboratories, Inc., 41-1, Yokomichi, Nagakute, Aichi 480-1192 (Japan); Ichiki, Akihisa; Motohiro, Tomoyoshi [Green Mobility Collaborative Research Center, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8601 (Japan)

2014-09-28

We have theoretically demonstrated a new light-trapping mechanism to reduce emission from a photovoltaic (PV) cell used for a monochromatic light source, which improves limiting conversion efficiency determined by the detailed balance. A multilayered bandpass filter formed on the surface of a PV cell has been found to prevent the light generated inside by radiative recombination from escaping the cell, resulting in a remarkable decrease of the effective solid angle for the emission. We have clarified a guide to design a suitable configuration of the bandpass filter and achieved significant reduction of the emission. The resultant gain in monochromatic conversion efficiency in the radiative limit due to the optimally designed 18-layerd bandpass filters is as high as 6% under normally incident 1064 nm illumination of 10 mW/cm²~ 1 kW/cm², compared with the efficiency for the perfect anti-reflection treatment to the surface of a conventional solar cell.

Normalization of satellite imagery

Science.gov (United States)

Kim, Hongsuk H.; Elman, Gregory C.

1990-01-01

Sets of Thematic Mapper (TM) imagery taken over the Washington, DC metropolitan area during the months of November, March and May were converted into a form of ground reflectance imagery. This conversion was accomplished by adjusting the incident sunlight and view angles and by applying a pixel-by-pixel correction for atmospheric effects. Seasonal color changes of the area can be better observed when such normalization is applied to space imagery taken in time series. In normalized imagery, the grey scale depicts variations in surface reflectance and tonal signature of multi-band color imagery can be directly interpreted for quantitative information of the target.

Reflectance spectrometry of normal and bruised human skins: experiments and modeling

International Nuclear Information System (INIS)

Kim, Oleg; Alber, Mark; McMurdy, John; Lines, Collin; Crawford, Gregory; Duffy, Susan

2012-01-01

A stochastic photon transport model in multilayer skin tissue combined with reflectance spectroscopy measurements is used to study normal and bruised skins. The model is shown to provide a very good approximation to both normal and bruised real skin tissues by comparing experimental and simulated reflectance spectra. The sensitivity analysis of the skin reflectance spectrum to variations of skin layer thicknesses, blood oxygenation parameter and concentrations of main chromophores is performed to optimize model parameters. The reflectance spectrum of a developed bruise in a healthy adult is simulated, and the concentrations of bilirubin, blood volume fraction and blood oxygenation parameter are determined for different times as the bruise progresses. It is shown that bilirubin and blood volume fraction reach their peak values at 80 and 55 h after contusion, respectively, and the oxygenation parameter is lower than its normal value during 80 h after contusion occurred. The obtained time correlations of chromophore concentrations in developing contusions are shown to be consistent with previous studies. The developed model uses a detailed seven-layer skin approximation for contusion and allows one to obtain more biologically relevant results than those obtained with previous models using one- to three-layer skin approximations. A combination of modeling with spectroscopy measurements provides a new tool for detailed biomedical studies of human skin tissue and for age determination of contusions. (paper)

Design and simulation of reflect-array metasurfaces in the visible regime

KAUST Repository

Alrasheed, Salma; Di Fabrizio, Enzo M.

2017-01-01

gradient phase gap-surface plasmon metasurfaces that exhibit high conversion efficiency (up to ∼97% of total reflected light) to the anomalous reflection angle for blue, green, and red wavelengths at normal and oblique incidence, and where light

Suppression of Specular Reflections by Metasurface with Engineered Nonuniform Distribution of Reflection Phase

Directory of Open Access Journals (Sweden)

Xin Mi Yang

2015-01-01

Full Text Available We make preliminary investigations on a new approach to reducing radar cross section (RCS of conducting objects. This approach employs novel planar metasurfaces characterizing nonuniform distribution of reflection phase. The operation principle of this approach and the design rule of the associated metasurfaces are explained using a simplified theoretical model. We then present a design example of such metasurfaces, in which three-layer stacked square patches with variable sizes are utilized as the reflecting elements. The proposed RCS-reduction approach is verified by both numerical simulations and measurements on the example, under the assumption of normal plane wave incidence. It is observed that, in a fairly wide frequency band (from 3.6 to 5.5 GHz, the presented example is capable of suppressing the specular reflections of conducting plates significantly (by more than 7 dB for two orthogonal incident polarizations.

Reflection of attosecond x-ray free electron laser pulses

International Nuclear Information System (INIS)

Hau-Riege, Stefan P.; Chapman, Henry N.

2007-01-01

In order to utilize hard x-ray free electron lasers (XFEL's) when they are extended to attosecond pulse lengths, it is necessary to choose optical elements with minimal response time. Specular grazing-incidence optics made of low-Z materials are popular candidates for reflectors since they are likely to withstand x-ray damage and provide sufficiently large reflectivities. Using linear-optics reflection theory, we calculated the transient reflectivity of a delta-function electric pulse from a homogenous semi-infinite medium as a function of angle of incidence for s- and p-polarized light. We specifically considered the pulse response of beryllium, diamond, silicon carbide, and silicon, all of which are of relevance to the XFEL's that are currently being built. We found that the media emit energy in a damped oscillatory way, and that the impulse-response times are shorter than 0.3 fs for normal incidence. For grazing incidence, the impulse-response time is substantially shorter, making grazing-incidence mirrors a good choice for deep subfemtosecond reflective optics

Pore-level determination of spectral reflection behaviors of high-porosity metal foam sheets

Science.gov (United States)

Li, Yang; Xia, Xin-Lin; Ai, Qing; Sun, Chuang; Tan, He-Ping

2018-03-01

Open cell metal foams are currently attracting attention and their radiative behaviors are of primary importance in high temperature applications. The spectral reflection behaviors of high-porosity metal foam sheets, bidirectional reflectance distribution function (BRDF) and directional-hemispherical reflectivity were numerically investigated. A set of realistic nickel foams with porosity from 0.87 to 0.97 and pore density from 10 to 40 pores per inch were tomographied to obtain their 3-D digital cell network. A Monte Carlo ray-tracing method was employed in order to compute the pore-level radiative transfer inside the network within the limit of geometrical optics. The apparent reflection behaviors and their dependency on the textural parameters and strut optical properties were comprehensively computed and analysed. The results show a backward scattering of the reflected energy at the foam sheet surface. Except in the cases of large incident angles, an energy peak is located almost along the incident direction and increases with increasing incident angles. Through an analytical relation established, the directional-hemispherical reflectivity can be related directly to the porosity of the foam sheet and to the complex refractive index of the solid phase as well as the specularity parameter which characterizes the local reflection model. The computations show that a linear decrease in normal-hemispherical reflectivity occurs with increasing porosity. The rate of this decrease is directly proportional to the strut normal reflectivity. In addition, the hemispherical reflectivity increases as a power function of the incident angle cosine.

Some simple ideas on x-ray reflection and grazing-incidence diffraction from thin surfactant films

DEFF Research Database (Denmark)

Kjær, K.

1994-01-01

For Langmuir films of long linear amphiphilic molecules at the air-water interface, grazing-incidence diffraction data resolved in terms of both the horizontal and vertical components of the scattering angle can be evaluated to a fair level of detail by means of a slide rule. Specular reflection ...... data require more sophisticated means although some rules of thumb can be formulated.......For Langmuir films of long linear amphiphilic molecules at the air-water interface, grazing-incidence diffraction data resolved in terms of both the horizontal and vertical components of the scattering angle can be evaluated to a fair level of detail by means of a slide rule. Specular reflection...

Reflection and transmission of full-vector X-waves normally incident on dielectric half spaces

KAUST Repository

Salem, Mohamed; Bagci, Hakan

2011-01-01

polarization components, which are derived from the scalar X-Wave solution. The analysis of transmission and reflection is carried out via a straightforward but yet effective method: First, the X-Wave is decomposed into vector Bessel beams via the Bessel-Fourier

Specular reflectance of soiled glass mirrors - Study on the impact of incidence angles

Science.gov (United States)

Heimsath, Anna; Lindner, Philip; Klimm, Elisabeth; Schmid, Tobias; Moreno, Karolina Ordonez; Elon, Yehonatan; Am-Shallem, Morag; Nitz, Peter

2016-05-01

The accumulation of dust and soil on the surface of solar reflectors is an important factor reducing the power output of solar power plants. Therefore the effect of accumulated dust on the specular reflectance of solar mirrors should be understood well in order to improve the site-dependent performance prediction. Furthermore, an optimization of the CSP System maintenance, in particular the cleaning cycles, can be achieved. Our measurements show a noticeable decrease of specular reflectance when the angle of incidence is increased. This effect may be explained by shading and blocking mechanisms caused by dirt particles. The main physical causes of radiation loss being absorption and scattering, the near-angle scattering leads to a further decrease of specular reflectance for smaller angles of acceptance. Within this study mirror samples were both outdoor exposed and indoor artificially soiled. For indoor soiling, the mirror samples were artificially soiled in an in-house developed dusting device using both artificial-standardized dust and real dust collected from an arid outdoor test field at the Negev desert. A model function is proposed that approximates the observed reduction of specular reflectance with the incidence angle with a sufficient accuracy and by simple means for this soil type. Hence a first step towards a new approach to improve site dependent performance prediction of solar power plants is taken.

Pump induced normal mode splittings in phase conjugation in a Kerr ...

Indian Academy of Sciences (India)

Abstract. Phase conjugation in a Kerr nonlinear waveguide is studied with counter-propagating normally incident pumps and a probe beam at an arbitrary angle of incidence. Detailed numerical results for the specular and phase conjugated reflectivities are obtained with full account of pump depletion. For sufficient ...

Impact of increasing alanine aminotransferase levels within normal range on incident diabetes

OpenAIRE

Chong-Shan Wang; Ting-Tsung Chang; Wei-Jen Yao; Shan-Tair Wang; Pesus Chou

2012-01-01

Abnormal alanine aminotransferase level (ALT) levels might be associated with type 2 diabetes, but whether higher ALT levels within the normal range predict the risk is unknown. Methods: We followed a community-based cohort of 3446 individuals who were ≥35 years old without diabetes and hepatitis B or C in southern Taiwan for 8 years (1997–2004) to study the risk for type 2 diabetes with different normal ALT levels. Results: Among the 337 incident diabetes cases, 16.0% were from those w...

Studies on normal incidence backscattering in nodule areas using the multibeam-hydrosweep system

Digital Repository Service at National Institute of Oceanography (India)

Pathak, D.; Chakraborty, B.

The acoustic response from areas of varying nodule abundance and number densities in the Central Indian Ocean has been studied by using the echo peak amplitudes of the normal incidence beam in the Multibeam Hydrosweep system. It is observed...

Grazing incidence infrared reflectivity of La1.85Sr0.15CuO4 and NbN

NARCIS (Netherlands)

Somal, HS; Feenstra, BJ; Schutzmann, J; Kim, JH; Barber, ZH; Duijn, VHM; Hien, NT; Menovsky, AA; Palumbo, M; vanderMarel, D

1996-01-01

Infrared reflectivity measurements, using p-polarized light at a grazing angle of incidence, show an increased sensitivity to the optical conductivity of highly reflecting superconducting materials. We demonstrate that when this measurement technique is applied to the conventional s-wave

Lunar occultation of Saturn. II - The normal reflectance of Rhea, Titan, and Iapetus

Science.gov (United States)

Elliot, J. L.; Dunham, E. W.; Veverka, J.; Goguen, J.

1978-01-01

An inversion procedure to obtain the reflectance of the central region of a satellite's disk from lunar occultation data is presented. The scheme assumes that the limb darkening of the satellite depends only on the radial distance from the center of the disk. Given this assumption, normal reflectances can be derived that are essentially independent of the limb darkening and the diameter of the satellite. The procedure has been applied to our observations of the March 1974 lunar occultation of Tethys, Dione, Rhea, Titan, and Iapetus. In the V passband we derive the following normal reflectances: Rhea (0.97 plus or minus 0.20), Titan (0.24 plus or minus 0.03), Iapetus, bright face (0.60 plus or minus 0.14). For Tethys and Dione the values derived have large uncertainties, but are consistent with our result for Rhea.

Oblique-incidence reflectivity difference application for morphology detection.

Science.gov (United States)

Zhan, Honglei; Zhao, Kun; Lü, Huibin; Jin, Kuijuan; Yang, Guozhen; Chen, Xiaohong

2017-10-20

Analogous with scanning electron microscopy, we use an oblique-incidence reflectivity difference (OIRD) approach for morphology detection. By scanning the active carbon clusters in a one-dimensional way and the reservoir rocks in a two-dimensional way, the morphology of the samples' surface can be revealed in OIRD signal images. High OIRD signals of active carbon samples refer to the centralized distribution areas of carbon, and the fluctuations are caused by the uneven distribution of carbon pellets. OIRD intensity is proportional to the thickness of materials. In terms of rocks, the trough areas with smaller values refer to the low-lying fields. The areas with relatively large OIRD intensities correspond to the protuberance areas of rocks. Consequently, OIRD is a sensitive yet rapid measure of surface detection in material and petrogeology science.

Efficient anomalous reflection through near-field interactions in metasurfaces

Science.gov (United States)

Chalabi, H.; Ra'di, Y.; Sounas, D. L.; Alù, A.

2017-08-01

Gradient metasurfaces have been extensively used in the past few years for advanced wave manipulation over a thin surface. These metasurfaces have been mostly designed based on the generalized laws of reflection and refraction. However, it was recently revealed that metasurfaces based on this approach tend to suffer from inefficiencies and complex design requirements. We have recently proposed a different approach to the problem of efficient beam steering using a surface, based on bianisotropic particles in a periodic array. Here, we show highly efficient reflective metasurfaces formed by pairs of isotropic dielectric rods, which can offer asymmetrical scattering of normally incident beams with unitary efficiency. Our theory shows that moderately broadband anomalous reflection can be achieved with suitably designed periodic arrays of isotropic nanoparticles. We also demonstrate practical designs using TiO2 cylindrical nanorods to deflect normally incident light toward a desired direction. The proposed structures may pave the way to a broader range of light management opportunities, with applications in energy harvesting, signaling, and communications.

Energy dependence of ion-induced sputtering yields from monoatomic solids at normal incidence

International Nuclear Information System (INIS)

Yamamura, Yasunori; Tawara, Hiro.

1995-03-01

The yields of the ion-induced sputtering from monoatomic solids at normal incidence for various ion-target combinations are presented graphically as a function of the incident ion energy. In order to fill the lack of the experimental data, the sputtering yields are also calculated by the Monte Carlo simulation code ACAT for some ion-target combinations. Each graph shows available experimental data points and the ACAT data, together with the sputtering yields calculated by the present empirical formula, whose parameters are determined by the best-fit to available data. (author)

Properties of backward electromagnetic waves and negative reflection in ferrite films

International Nuclear Information System (INIS)

Vashkovsky, Anatolii V; Lock, Edwin H

2006-01-01

For a backward electromagnetic wave (magnetostatic wave) in a ferrite film, reflection from a perfect mirror formed by the straight edge of the film is investigated experimentally and theoretically. It is found that when the incident wave is collinear (the group velocity vector and the wave vector have opposite directions), negative reflection occurs at any angle of incidence, i.e., the incident and reflected beams are on the same side of the normal to the boundary. It is discovered that a noncollinear backward wave is nonreciprocal in the sense that its energy can be localized both near the surface and in the middle of the film. This property, previously observed only for surface magnetostatic waves, provides both the efficiency of generating and receiving the wave and the possibility of observing the reflected beam. A situation is realized where wave reflection results in two reflected beams. The properties of backward electromagnetic waves propagating in ferrite films are briefly analyzed. (methodological notes)

Unusual reflection of electromagnetic radiation from a stack of graphene layers at oblique incidence

International Nuclear Information System (INIS)

Bludov, Yu V; Peres, N M R; Vasilevskiy, M I

2013-01-01

We study the interaction of electromagnetic (EM) radiation with single-layer graphene and a stack of parallel graphene sheets at arbitrary angles of incidence. It is found that the behavior is qualitatively different for transverse magnetic (or p-polarized) and transverse electric (or s-polarized) waves. In particular, the absorbance of single-layer graphene attains a minimum (maximum) for the p (s)-polarization at the angle of total internal reflection when the light comes from a medium with a higher dielectric constant. In the case of equal dielectric constants of the media above and beneath graphene, for grazing incidence graphene is almost 100% transparent to p-polarized waves and acts as a tunable mirror for the s-polarization. These effects are enhanced for a stack of graphene sheets, so the system can work as a broad band polarizer. It is shown further that a periodic stack of graphene layers has the properties of a one-dimensional photonic crystal, with gaps (or stop bands) at certain frequencies. When an incident EM wave is reflected from this photonic crystal, the tunability of the graphene conductivity renders the possibility of controlling the gaps, and the structure can operate as a tunable spectral-selective mirror. (paper)

Probing near-normally propagating bulk acoustic waves using pseudo-reflection geometry Brillouin spectroscopy

Science.gov (United States)

Parsons, L. C.; Andrews, G. T.

2012-09-01

Pseudo-reflection geometry Brillouin spectroscopy can be used to probe acoustic wave dispersion approximately along the surface normal of a material system while avoiding the difficulties associated with specularly reflected light encountered in an ideal reflection configuration. As an example of its application, we show analytically that it can be used to determine both the refractive index and bulk acoustic mode velocities of optically-isotropic non-metallic materials and confirm the utility of the approach via a series of experiments on fused quartz, gallium phosphide, water, and porous silicon films.

THE EFFECT OF WAIST CIRCUMFERENCES MORE THAN NORMAL ON THE INCIDENT OF CORONARY HEART DISEASE

Directory of Open Access Journals (Sweden)

Pria Wahyu

2017-07-01

Full Text Available Introduction: Coronary heart disease is known as the most common disease that causes mortality in the world, one of the examination to identify the risks of coronary heart disease is measuring waist circumference. The purpose of this study was to identify correlation between large waist circumferences and the incident of coroner heart disease. Method: Design used in this study was analytic observational (retrospective with cross sectional approach. There were 63 respondents which sampling by simple random sampling. The independent variable was waist circumferences and the dependent variable was coronary heart disease. Data were collected by direct observation then analyzed by spearman correlation statistic test with significance level α≤0.05. Result: The result showed that waist circumferences more than normal had significant correlation with the incident of coronary heart disease (p=0.02. Analysis: It can be concluded that there was correlation between waist circumferences more than normal and the incident of coronary heart disease to the clients with coroner cardiac disease. Discussion: Earlier screening and detection is needed to prevent coronary heart disease.

Andreev reflection in monolayer MoS2

Science.gov (United States)

Majidi, Leyla; Rostami, Habib; Asgari, Reza

2014-01-01

Andreev reflection in a monolayer molybdenum disulfide superconducting-normal (S/N) hybrid junction is investigated. We find, by using a modified Dirac Hamiltonian and the scattering formalism, that the perfect Andreev reflection happens at normal incidence with p-doped S and N regions. The probability of the Andreev reflection and the resulting Andreev conductance, in this system, are demonstrated to be large in comparison with the corresponding gapped graphene structure. We further investigate the effect of a topological term (β ) in the Hamiltonian and show that it results in an enhancement of the Andreev conductance with p-doped S and N regions, while in the corresponding structure with an n-doped S region it is strongly reducible in comparison. This effect can be explained in terms of the dependence of the Andreev reflection probability on the sign of β and the chemical potential in the superconducting region.

Assessment of radiation doses due to normal operation, incidents and accidents of the final disposal facility

International Nuclear Information System (INIS)

Rossi, J.; Raiko, H.; Suolanen, V.; Ilvonen, M.

1999-03-01

Radiation doses for workers of the encapsulation and disposal facility and for inhabitants in the environment caused by the facility during its operation were considered. The study covers both the normal operation of the plant and some hypothetical incidents and accidents. Occupational radiation doses inside the plant during normal operation are based on the design basis, assuming that highest permitted dose levels are prevailing in control rooms during fuel transfer and encapsulation processes. Release through the ventilation stack is assumed to be filtered both in normal operation and in hypothetical incident and accident cases. Calculation of the offsite doses from normal operation is based on the hypothesis that one fuel pin per 100 fuel bundles for all batches of spent fuel transported to the encapsulation facility is leaking. The release magnitude in incidents and accidents is based on the event chains, which lead to loss of fuel pin tightness followed by a discharge of radionuclides into the handling chamber and to some degree through the ventilation stack into atmosphere. The weather data measured at the Olkiluoto meteorological mast was employed for calculating of offsite doses. Therefore doses could be calculated in a large amount of different dispersion conditions, the statistical frequencies of which have, been measured. Finally doses were combined into cumulative distributions, from which a dose value representing the 99.5 % confidence level, is presented. The dose values represent the exposure of a critical group, which is assumed to live at the distance of 200 meters from the encapsulation and disposal plant and thus it will receive the largest doses in most dispersion conditions. Exposure pathways considered were: cloudsnine, inhalation, groundshine and nutrition (milk of cow, meat of cow, green vegetables, grain and root vegetables). Nordic seasonal variation is included in ingestion dose models. The results obtained indicate that offsite doses

Reflection of Alfven waves at an open magnetopause

International Nuclear Information System (INIS)

Cao, F.; Kan, J.R.

1990-01-01

Reflection of an Alfven wave incident on an open magnetopause form the magnetospheric side is examined. An open magnetopause, whose structure is different from the standard rotational discontinuity, is assumed to be a parameterized discontinuity with a nonzero normal field component. When an Alfven wave is incident on the open magnetopause, reflected and transmitted waves are generated. The emanating waves can be analyzed using linearized MHD conservation relations across the magnetopause, together with Snell's law. Under the assumption that the magnetic fields on the two sides of the open magnetopause are coplanar with the normal direction of the magnetopause, the governing equations are solved numerically. The results show that the electric fields of emanating Alfven waves depend mainly on the number density and the magnetic field jumps across the magnetopause. Under conditions representing the open magnetopause, it turns out that the open magnetopause behaves like a near perfect reflector. The corresponding reflection coefficient for the wave electric field can be approximated by R E = E r /E i ∼ -1 as has been deduced by Kan and Sun (1985) based on physical arguments. In other words, the solar wind flow is more or less unchanged by the loading effect of the Alfven wave incident on the magnetopause from the magnetospheric side. Therefore, under the assumptions of the model, the open magnetopause can be viewed as a constant voltage source

Normalization of multidirectional red and NIR reflectances with the SAVI

Science.gov (United States)

Huete, A. R.; Hua, G.; Qi, J.; Chehbouni, A.; Van Leeuwen, W. J. D.

1992-01-01

Directional reflectance measurements were made over a semi-desert gramma grassland at various times of the growing season. View angle measurements from +40 to -40 degrees were made at various solar zenith angles and soil moisture conditions. The sensitivity of the Normalized Difference Vegetation Index (NDVI) and the Soil Adjusted Vegetation Index (SAVI) to bidirectional measurements was assessed for purposes of improving remote temporal monitoring of vegetation dynamics. The SAVI view angle response was found to be symmetric about nadir while the NDVI response was strongly anisotropic. This enabled the view angle behavior of the SAVI to be normalized with a cosine function. In contrast to the NDVI, the SAVI was able to minimize soil moisture and shadow influences for all measurement conditions.

[Colorimetric investigation of normal tongue and lip colors from 516 healthy adults by visible reflection spectrum].

Science.gov (United States)

Zeng, Chang-chun; Yang, Li; Xu, Ying; Liu, Pei-pei; Guo, Shi-jun; Liu, Song-hao

2011-09-01

Using the data from normal tongue and lip colors of normal people which were collected by the visible reflection spectrum, we analyzed the colorimetric parameters of tongue and lip colors. In this study, 516 healthy students aging from 19 to 26 from the colleges and universities of Guangdong Province of China were taken as research subjects. After collecting the data of tongue and lip colors of the 516 subjects using visible reflectance spectroscopy, CIE XYZ tristimulus values as defined by the International Commission on Illumination in 1964 were calculated, and the colorimetric parameters of the normal tongue and lip colors were obtained, such as the CIE 1964 chromaticity coordinate, brightness, dominant wavelength and excitation purity. The results of CIE 1964 chromaticity diagram calculated on the visible reflection spectrum showed that the normal tongue color chromaticity coordinate x(10) was 0.341 3±0.008 5 and y(10) was 0.332 6±0.005 1, and the normal lip color chromaticity coordinate x(10) was 0.357 7±0.009 2 and y(10) was 0.338 3±0.005 7; the brightness Y values of the normal tongue color and lip colors were 17.96±3.78 and 19.78±3.72, the dominant wavelength values of the normal tongue color and lip color were (626.3±51.6) nm and (600.4±18.2) nm, and the excitation purity values of the normal tongue color and lip color were 0.083±0.031 and 0.144±0.036, respectively. Application of the visible reflection spectrum is a standard way to collect colorimetric data for inspection of the complexion. The investigation of chromaticity coordinates, brightness, dominant wavelength and excitation purity of the normal tongue and lip colors may offer the basic reference for diagnosing morbid complexion on the tongue and lip colors in traditional Chinese medicine.

Analytical evaluation for the sputtering yield of monoatomic solids at normal ion incidence

International Nuclear Information System (INIS)

Shao Qiyun; Pan Zhengying

1994-01-01

A universal formula of sputtering yield for normal incidence of mono-energetic ions on single element targets is presented. The results based on this method are compared with the Monte Carlo simulation and the experimental data. By means of Wilcoxon two-sample paired signed rank test, the statistically significant difference of the above results is discussed

First combined total reflection X-ray fluorescence and grazing incidence X-ray absorption spectroscopy characterization of aeolian dust archived in Antarctica and Alpine deep ice cores

Energy Technology Data Exchange (ETDEWEB)

Cibin, G. [Diamond Light Source, Harwell Science and Innovation Campus, Didcot, Oxon OX110DE (United Kingdom); IMONT/EIM, Ente Italiano della Montagna, P.za dei Caprettari 70, 00176 Roma (Italy); Universita' degli Studi di Roma Tre, Dipartimento di Scienze Geologiche, L.go S. Leonardo Murialdo 1, 00146 Roma (Italy)], E-mail: giannantonio.cibin@diamond.ac.uk; Marcelli, A. [INFN - Laboratori Nazionali di Frascati, P.O. Box 13, 00044 Frascati (Roma) (Italy); Maggi, V. [Universita degli Studi di Milano-Bicocca, Dipartimento di Scienze dell' Ambiente e del Territorio, Piazza della Scienza 1, 20126 Milano (Italy); Sala, M. [Universita degli Studi di Milano-Bicocca, Dipartimento di Scienze dell' Ambiente e del Territorio, Piazza della Scienza 1, 20126 Milano (Italy); Universita degli Studi di Milano, Dipartimento di Scienze della Terra ' A. Desio' , Sez. Mineralogia, Via Mangiagalli 34, 20133 Milano (Italy); Marino, F.; Delmonte, B. [Universita degli Studi di Milano-Bicocca, Dipartimento di Scienze dell' Ambiente e del Territorio, Piazza della Scienza 1, 20126 Milano (Italy); Albani, S. [Universita degli Studi di Milano-Bicocca, Dipartimento di Scienze dell' Ambiente e del Territorio, Piazza della Scienza 1, 20126 Milano (Italy); Universita degli Studi di Siena, Dottorato in Scienze Polari, via Laterina 8, 53100 Siena (Italy); Pignotti, S. [IMONT/EIM, Ente Italiano della Montagna, P.za dei Caprettari 70, 00176 Roma (Italy)

2008-12-15

Aeolian mineral dust archived in polar and mid latitude ice cores represents a precious proxy for assessing environmental and climatic variations at different timescales. In this respect, the identification of dust mineralogy plays a key role. In this work we performed the first preliminary X-ray absorption spectroscopy (XAS) experiments on mineral dust particles extracted from Antarctic and from Alpine firn cores using grazing incidence geometry at the Fe K-edge. A dedicated high vacuum experimental chamber was set up for normal-incidence and total-reflection X-Ray Fluorescence and Absorption Spectroscopy analyses on minor amounts of mineral materials at the Stanford Synchrotron Radiation Laboratory. Results show that this experimental technique and protocol allows recognizing iron inclusion mineral fraction on insoluble dust in the 1-10 {mu}g range.

First combined total reflection X-ray fluorescence and grazing incidence X-ray absorption spectroscopy characterization of aeolian dust archived in Antarctica and Alpine deep ice cores

International Nuclear Information System (INIS)

Cibin, G.; Marcelli, A.; Maggi, V.; Sala, M.; Marino, F.; Delmonte, B.; Albani, S.; Pignotti, S.

2008-01-01

Aeolian mineral dust archived in polar and mid latitude ice cores represents a precious proxy for assessing environmental and climatic variations at different timescales. In this respect, the identification of dust mineralogy plays a key role. In this work we performed the first preliminary X-ray absorption spectroscopy (XAS) experiments on mineral dust particles extracted from Antarctic and from Alpine firn cores using grazing incidence geometry at the Fe K-edge. A dedicated high vacuum experimental chamber was set up for normal-incidence and total-reflection X-Ray Fluorescence and Absorption Spectroscopy analyses on minor amounts of mineral materials at the Stanford Synchrotron Radiation Laboratory. Results show that this experimental technique and protocol allows recognizing iron inclusion mineral fraction on insoluble dust in the 1-10 μg range

X ray reflection masks: Manufacturing, characterization and first tests

Science.gov (United States)

Rahn, Stephen

1992-09-01

SXPL (Soft X-ray Projection Lithography) multilayer mirrors are characterized, laterally structured and then used as reflection masks in a projecting lithography procedure. Mo/Si-multilayer mirrors with a 2d in the region of 14 nm were characterized by Cu-k(alpha) grazing incidence as well as soft X-ray normal incidence reflectivity measurements. The multilayer mirrors were patterned by reactive ion etching with CF4 using a photoresist as etch mask, thus producing X-ray reflection masks. The masks were tested at the synchrotron radiation laboratory of the electron accelerator ELSA. A double crystal X-ray monochromator was modified so as to allow about 0.5 sq cm of the reflection mask to be illuminated by white synchrotron radiation. The reflected patterns were projected (with an energy of 100 eV) onto a resist and structure sizes down to 8 micrometers were nicely reproduced. Smaller structures were distorted by Fresnel-diffraction. The theoretically calculated diffraction images agree very well with the observed images.

Reflectance Measures from Infant Ears With Normal Hearing and Transient Conductive Hearing Loss.

Science.gov (United States)

Voss, Susan E; Herrmann, Barbara S; Horton, Nicholas J; Amadei, Elizabeth A; Kujawa, Sharon G

2016-01-01

The objective is to develop methods to utilize newborn reflectance measures for the identification of middle-ear transient conditions (e.g., middle-ear fluid) during the newborn period and ultimately during the first few months of life. Transient middle-ear conditions are a suspected source of failure to pass a newborn hearing screening. The ability to identify a conductive loss during the screening procedure could enable the referred ear to be either (1) cleared of a middle-ear condition and recommended for more extensive hearing assessment as soon as possible, or (2) suspected of a transient middle-ear condition, and if desired, be rescreened before more extensive hearing assessment. Reflectance measurements are reported from full-term, healthy, newborn babies in which one ear referred and one ear passed an initial auditory brainstem response newborn hearing screening and a subsequent distortion product otoacoustic emission screening on the same day. These same subjects returned for a detailed follow-up evaluation at age 1 month (range 14 to 35 days). In total, measurements were made on 30 subjects who had a unilateral refer near birth (during their first 2 days of life) and bilateral normal hearing at follow-up (about 1 month old). Three specific comparisons were made: (1) Association of ear's state with power reflectance near birth (referred versus passed ear), (2) Changes in power reflectance of normal ears between newborn and 1 month old (maturation effects), and (3) Association of ear's newborn state (referred versus passed) with ear's power reflectance at 1 month. In addition to these measurements, a set of preliminary data selection criteria were developed to ensure that analyzed data were not corrupted by acoustic leaks and other measurement problems. Within 2 days of birth, the power reflectance measured in newborn ears with transient middle-ear conditions (referred newborn hearing screening and passed hearing assessment at age 1 month) was significantly

Solar cell angle of incidence corrections

Science.gov (United States)

Burger, Dale R.; Mueller, Robert L.

1995-01-01

Literature on solar array angle of incidence corrections was found to be sparse and contained no tabular data for support. This lack along with recent data on 27 GaAs/Ge 4 cm by 4 cm cells initiated the analysis presented in this paper. The literature cites seven possible contributors to angle of incidence effects: cosine, optical front surface, edge, shadowing, UV degradation, particulate soiling, and background color. Only the first three are covered in this paper due to lack of sufficient data. The cosine correction is commonly used but is not sufficient when the incident angle is large. Fresnel reflection calculations require knowledge of the index of refraction of the coverglass front surface. The absolute index of refraction for the coverglass front surface was not known nor was it measured due to lack of funds. However, a value for the index of refraction was obtained by examining how the prediction errors varied with different assumed indices and selecting the best fit to the set of measured values. Corrections using front surface Fresnel reflection along with the cosine correction give very good predictive results when compared to measured data, except there is a definite trend away from predicted values at the larger incident angles. This trend could be related to edge effects and is illustrated by a use of a box plot of the errors and by plotting the deviation of the mean against incidence angle. The trend is for larger deviations at larger incidence angles and there may be a fourth order effect involved in the trend. A chi-squared test was used to determine if the measurement errors were normally distributed. At 10 degrees the chi-squared test failed, probably due to the very small numbers involved or a bias from the measurement procedure. All other angles showed a good fit to the normal distribution with increasing goodness-of-fit as the angles increased which reinforces the very small numbers hypothesis. The contributed data only went to 65 degrees

Sound excitation at reflection of two electromagnetic waves from dence semibounded plasma

International Nuclear Information System (INIS)

Livdan, D.O.; Muratov, V.I.; Shuklin, A.P.

1988-01-01

The problem of two electromagnetic waves reflection by semibounded plasma which is nontransparent for each of these waves is solved. The reflection coefficients are obtained for normally incident waves. It is shown that the moduli of the reflection coefficients differ from the unit and this is due to the interaction of the external raiation with the acoustic wave excited in plasma. The energy flux in plasma is calculated

Numerical solutions of several reflected shock-wave flow fields with nonequilibrium chemical reactions

Science.gov (United States)

Hanson, R. K.; Presley, L. L.; Williams, E. V.

1972-01-01

The method of characteristics for a chemically reacting gas is used in the construction of the time-dependent, one-dimensional flow field resulting from the normal reflection of an incident shock wave at the end wall of a shock tube. Nonequilibrium chemical reactions are allowed behind both the incident and reflected shock waves. All the solutions are evaluated for oxygen, but the results are generally representative of any inviscid, nonconducting, and nonradiating diatomic gas. The solutions clearly show that: (1) both the incident- and reflected-shock chemical relaxation times are important in governing the time to attain steady state thermodynamic properties; and (2) adjacent to the end wall, an excess-entropy layer develops wherein the steady state values of all the thermodynamic variables except pressure differ significantly from their corresponding Rankine-Hugoniot equilibrium values.

New optical scheme for differential measurements of diffraction reflection intensity on X-radiation sliding incidence

International Nuclear Information System (INIS)

Golovin, A.L.; Mas', E.T.

1989-01-01

An X-ray optical scheme for differential measurements of X-ray diffraction under sliding incidence conditions is proposed and an attachment design realizng this scheme, using standard equipment, is described. The main feature of the scheme is the following: collimation according to the Bragg angle is carried out for the reflected beam rather than the incident one. Goniometers can be used from DRON, TRS, GS-5 and other spectrometers. The goniometer head carrying the sample is standard, it is a part of the DRON, TRS and DTS. The crystal analyzer is fixed on the attachment. The angular position of the crystal monochromator is controlled by an inductive sensor. The experimental differential curves of X-ray diffraction under conditions of sliding incidence, taken for a silicon crystal having the 111 orientation, are given as well

Calculation of Reflectance and Transmittance of Coating With Optically Rough Surfaces

International Nuclear Information System (INIS)

El-Depsy, A.; Shawky, A.M.

2011-01-01

For ideal surfaces, components of the reflected beam are related to the components of the incident beam by Fresnel reflection equation. The surfaces encountered in engineering applications deviate from ideal as a result of roughness, oxidization and contamination; hence the Radiative properties of these real surfaces differ greatly from those predicted by electromagnetic theory. In regard to problems of radiative heat transfer; the roughness of surfaces may be divided into two categories: (1) small surface irregularities such that the incident radiation cannot undergo more than a single reflection, (2) deep cavities in which the incident radiation undergoes multi-reflection. The normally incident radiation from rough surface having small irregularities is reflected partly specularly and partly diffusely [1]. Kubelka-Munk theory (K-M) [2] describes optical characteristics (e.g. reflectance, transmittance and absorbance) by a variety of light scattering media including paints, textiles and papers, and It is widely used in various industrial applications. Moder developments in radiative transfer theory (RTT) enable the derivation of (K-M) parameters from first principles [3]. Kubelka and Munk proposed a theory based on a model of two light fluxes travelling in the forward and backward directions. Subsequently a number of authors refined the theory and compared it with experimental data [4]. Several authors attempted to relate the Kubelka- Munk coefficients to the transport coefficients [5,6

Plasmonic Light Scattering in Textured Silicon Solar Cells with Indium Nanoparticles from Normal to Non-Normal Light Incidence

Directory of Open Access Journals (Sweden)

Wen-Jeng Ho

2017-07-01

Full Text Available In this study, we sought to improve the light trapping of textured silicon solar cells using the plasmonic light scattering of indium nanoparticles (In NPs of various dimensions. The light trapping modes of textured-silicon surfaces with and without In NPs were investigated at an angle of incidence (AOI ranging from 0° to 75°. The optical reflectance, external quantum efficiency (EQE, and photovoltaic performance were first characterized under an AOI of 0°. We then compared the EQE and photovoltaic current density-voltage (J-V as a function of AOI in textured silicon solar cells with and without In NPs. We observed a reduction in optical reflectance and an increase in EQE when the cells textured with pyramidal structures were coated with In NPs. We also observed an impressive increase in the average weighted external quantum efficiency (∆EQEw and short-circuit current-density (∆Jsc in cells with In NPs when illuminated under a higher AOI. The ∆EQEw values of cells with In NPs were 0.37% higher than those without In NPs under an AOI of 0°, and 3.48% higher under an AOI of 75°. The ∆Jsc values of cells with In NPs were 0.50% higher than those without In NPs under an AOI of 0°, and 4.57% higher under an AOI of 75°. The application of In NPs clearly improved the light trapping effects. This can be attributed to the effects of plasmonic light-scattering over the entire wavelength range as well as an expanded angle of incident light.

Trajectory effects in the negative charge-state fraction of 3He and 4He reflected from a sodium target

International Nuclear Information System (INIS)

Schneider, P.J.; Eckstein, W.; Verbeek, H.

1984-01-01

Measurement of the positive and negative charge-state fractions of He reflected from a sodium target with incident energies in the range of 1.75 keV/nucleon to 5 keV/nucleon are presented. The exit angle of the particles was held constant at 75 0 from the surface normal, while the incident angle was varied from 0 0 (normal incidence) to 75 0 . The positive charge-state fractions exhibited no incident-angle or incident-energy dependence and dependend only upon the exit energy. For normal incidence, the negative charge-state fractions were also only dependent upon the exit energy. However, for glancing incidence, the negative charge-state fractions were incident- and exit-energy dependent. These results are compared to previous results for D [1] and are discussed in terms of the trajectory-dependent formation probability of the negative ions. (orig.)

Normalization of time-series satellite reflectance data to a standard sun-target-sensor geometry using a semi-empirical model

Science.gov (United States)

Zhao, Yongguang; Li, Chuanrong; Ma, Lingling; Tang, Lingli; Wang, Ning; Zhou, Chuncheng; Qian, Yonggang

2017-10-01

Time series of satellite reflectance data have been widely used to characterize environmental phenomena, describe trends in vegetation dynamics and study climate change. However, several sensors with wide spatial coverage and high observation frequency are usually designed to have large field of view (FOV), which cause variations in the sun-targetsensor geometry in time-series reflectance data. In this study, on the basis of semiempirical kernel-driven BRDF model, a new semi-empirical model was proposed to normalize the sun-target-sensor geometry of remote sensing image. To evaluate the proposed model, bidirectional reflectance under different canopy growth conditions simulated by Discrete Anisotropic Radiative Transfer (DART) model were used. The semi-empirical model was first fitted by using all simulated bidirectional reflectance. Experimental result showed a good fit between the bidirectional reflectance estimated by the proposed model and the simulated value. Then, MODIS time-series reflectance data was normalized to a common sun-target-sensor geometry by the proposed model. The experimental results showed the proposed model yielded good fits between the observed and estimated values. The noise-like fluctuations in time-series reflectance data was also reduced after the sun-target-sensor normalization process.

Sound Reflection from the Sea Floor and its Geological Significance (NODC Accession 7001147)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The objective of this investigation was to measure bottom loss in normal incident reflection of pluses of twelve keps sound and to study its geological significance....

High-flux normal incidence monochromator for circularly polarized synchrotron radiation

International Nuclear Information System (INIS)

Schaefers, F.; Peatman, W.; Eyers, A.; Heckenkamp, C.; Schoenhense, G.; Heinzmann, U.

1986-01-01

A 6.5-m normal incidence monochromator installed at the storage ring BESSY, which is optimized for a high throughput of circularly polarized off-plane radiation at moderate resolution is described. The monochromator employs two exit slits and is specially designed and used for low-signal experiments such as spin- and angle-resolved photoelectron spectroscopy on solids, adsorbates, free atoms, and molecules. The Monk--Gillieson mounting (plane grating in a convergent light beam) allows for large apertures with relatively little astigmatism. With two gratings, a flux of more than 10 11 photons s -1 bandwidth -1 (0.2--0.5 nm) with a circular polarization of more than 90% in the wavelength range from 35 to 675 nm is achieved

Stress measurements by multi-reflection grazing-incidence X-ray diffraction method (MGIXD) using different radiation wavelengths and different incident angles

International Nuclear Information System (INIS)

Marciszko, Marianna; Baczmański, Andrzej; Braham, Chedly; Wróbel, Mirosław; Wroński, Sebastian; Cios, Grzegorz

2017-01-01

The presented study introduces the development of the multi-reflection grazing-incidence X-ray diffraction method (MGIXD) for residual stress determination. The proposed new methodology is aimed at obtaining more reliable experimental data and increasing the depth of non-destructive stress determination below the sample surface. To verify proposed method measurements were performed on a classical X-ray diffractometer (Cu Kα radiation) and using synchrotron radiation (three different wavelengths: λ = 1.2527 Å, λ = 1.5419 Å and λ = 1.7512 Å). The Al2017 alloy subjected to three different surface treatments was investigated in this study. The obtained results showed that the proposed development of MGIXD method, in which not only different incident angles but also different wavelengths of X-ray are used, can be successfully applied for residual stress determination, especially when stress gradients are present in the sample.

Far-infrared /FIR/ optical black bidirectional reflectance distribution function /BRDF/

Science.gov (United States)

Smith, S. M.

1981-01-01

A nonspecular reflectometer and its operation at far-infrared wavelengths are described. Large differences in nonspecular reflectance were found to exist between different optically black coatings. Normal incidence bidirectional reflectance distribution function /BRDF) measurements at wavelengths between 12 and 316 microns of three black coatings show that their mean BRDFs increase with wavelength. The specularity of two of these coatings also showed a strong wavelength dependence, while the specularity of one coating seemed independent of wavelength. The BRDF of one coating depended on the angle of incidence at 12 and 38 microns, but not at 316 microns. Beyond 200 microns, it was found necessary to correct the measurements for the beam spread of the instrument.

Dependence of the solar absorptance of selective absorber coatings on the angle of incidence

Energy Technology Data Exchange (ETDEWEB)

Reed, K A

1977-01-01

The directional solar absorptances ..cap alpha../sub s/(theta) of samples of a number of selective absorber coatings have been determined. The spectral directional hemispherical reflectances plambda(theta;2..pi..) of each sample was measured over the wavelength range 0.3..mu.. to 2.5..mu.. at angles of incidence theta between 10/sup 0/ and 80/sup 0/. The quantity (1-plambda(theta;2..pi..)) was convoluted over an AM2 solar spectrum to obtain ..cap alpha../sub s/(theta) at each angle of incidence. The solar absorptance at near normal incidence varied from sample to sample and from coating to coating, as expected, given the present state of the art. All the absorptances show similar angular dependences, however. When normalized to unity at normal incidence, the data nearly describe a single curve, for which a power series in theta was found. For comparison, the solar absorptance was also determined for freshly prepared lamp black.

High Reflectance Nanoscale V/Sc Multilayer for Soft X-ray Water Window Region.

Science.gov (United States)

Huang, Qiushi; Yi, Qiang; Cao, Zhaodong; Qi, Runze; Loch, Rolf A; Jonnard, Philippe; Wu, Meiyi; Giglia, Angelo; Li, Wenbin; Louis, Eric; Bijkerk, Fred; Zhang, Zhong; Wang, Zhanshan

2017-10-10

V/Sc multilayer is experimentally demonstrated for the first time as a high reflectance mirror for the soft X-ray water window region. It primarily works at above the Sc-L edge (λ = 3.11 nm) under near normal incidence while a second peak appears at above the V-L edge (λ = 2.42 nm) under grazing incidence. The V/Sc multilayer fabricated with a d-spacing of 1.59 nm and 30 bilayers has a smaller interface width (σ = 0.27 and 0.32 nm) than the conventional used Cr/Sc (σ = 0.28 and 0.47 nm). For V/Sc multilayer with 30 bilayers, the introduction of B 4 C barrier layers has little improvement on the interface structure. As the number of bilayers increasing to 400, the growth morphology and microstructure of the V/Sc layers evolves with slightly increased crystallization. Nevertheless, the surface roughness remains to be 0.25 nm. A maximum soft X-ray reflectance of 18.4% is measured at λ = 3.129 nm at 9° off-normal incidence using the 400-bilayers V/Sc multilayer. According to the fitted model, an s-polarization reflectance of 5.2% can also be expected at λ = 2.425 nm under 40° incidence. Based on the promising experimental results, further improvement of the reflectance can be achieved by using a more stable deposition system, exploring different interface engineering methods and so on.

Reflection and self-sputtering of nickel at oblique angles of ion incidence

International Nuclear Information System (INIS)

Hechtl, E.; Eckstein, W.; Roth, J.

1994-01-01

Measurement of the erosion yield of a target under ion bombardment using the weight change determines the sum of the sputtering yield and the particle reflection coefficient. The different erosion behavior of a volatile (Kr) and a nonvolatile projectile (Ni) are investigated on a nickel target in the energy range from 60 eV to 10 keV at an incidence angle of 75 . The angular dependence of the erosion yield is studied for 100, 500, and 2500 eV. In comparison with Monte Carlo calculations using the TRIM.SP program it is shown that at low energies ( 1 keV). (orig.)

Kinematics of reflections in subsurface offset and angle-domain image gathers

Science.gov (United States)

Dafni, Raanan; Symes, William W.

2018-05-01

Seismic migration in the angle-domain generates multiple images of the earth's interior in which reflection takes place at different scattering-angles. Mechanically, the angle-dependent reflection is restricted to happen instantaneously and at a fixed point in space: Incident wave hits a discontinuity in the subsurface media and instantly generates a scattered wave at the same common point of interaction. Alternatively, the angle-domain image may be associated with space-shift (regarded as subsurface offset) extended migration that artificially splits the reflection geometry. Meaning that, incident and scattered waves interact at some offset distance. The geometric differences between the two approaches amount to a contradictory angle-domain behaviour, and unlike kinematic description. We present a phase space depiction of migration methods extended by the peculiar subsurface offset split and stress its profound dissimilarity. In spite of being in radical contradiction with the general physics, the subsurface offset reveals a link to some valuable angle-domain quantities, via post-migration transformations. The angle quantities are indicated by the direction normal to the subsurface offset extended image. They specifically define the local dip and scattering angles if the velocity at the split reflection coordinates is the same for incident and scattered wave pairs. Otherwise, the reflector normal is not a bisector of the opening angle, but of the corresponding slowness vectors. This evidence, together with the distinguished geometry configuration, fundamentally differentiates the angle-domain decomposition based on the subsurface offset split from the conventional decomposition at a common reflection point. An asymptotic simulation of angle-domain moveout curves in layered media exposes the notion of split versus common reflection point geometry. Traveltime inversion methods that involve the subsurface offset extended migration must accommodate the split geometry

Aplanatic telescopes based on Schwarzschild optical configuration: from grazing incidence Wolter-like x-ray optics to Cherenkov two-mirror normal incidence telescopes

Science.gov (United States)

Sironi, Giorgia

2017-09-01

At the beginning of XX century Karl Schwarzschild defined a method to design large-field aplanatic telescopes based on the use of two aspheric mirrors. The approach was then refined by Couder (1926) who, in order to correct for the astigmatic aberration, introduced a curvature of the focal plane. By the way, the realization of normal-incidence telescopes implementing the Schwarzschild aplanatic configuration has been historically limited by the lack of technological solutions to manufacture and test aspheric mirrors. On the other hand, the Schwarzschild solution was recovered for the realization of coma-free X-ray grazing incidence optics. Wolter-like grazing incidence systems are indeed free of spherical aberration, but still suffer from coma and higher order aberrations degrading the imaging capability for off-axis sources. The application of the Schwarzschild's solution to X-ray optics allowed Wolter to define an optical system that exactly obeys the Abbe sine condition, eliminating coma completely. Therefore these systems are named Wolter-Schwarzschild telescopes and have been used to implement wide-field X-ray telescopes like the ROSAT WFC and the SOHO X-ray telescope. Starting from this approach, a new class of X-ray optical system was proposed by Burrows, Burg and Giacconi assuming polynomials numerically optimized to get a flat field of view response and applied by Conconi to the wide field x-ray telescope (WFXT) design. The Schwarzschild-Couder solution has been recently re-discovered for the application to normal-incidence Cherenkov telescopes, thanks to the suggestion by Vassiliev and collaborators. The Italian Institute for Astrophysics (INAF) realized the first Cherenkov telescope based on the polynomial variation of the Schwarzschild configuration (the so-called ASTRI telescope). Its optical qualification was successfully completed in 2016, demonstrating the suitability of the Schwarzschild-like configuration for the Cherenkov astronomy requirements

Reflective masks for extreme ultraviolet lithography

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Khanh Bao [Univ. of California, Berkeley, CA (United States)

1994-05-01

Extreme ultraviolet lithographic masks are made by patterning multilayer reflective coatings with high normal incidence reflectivity. Masks can be patterned by depositing a patterned absorber layer above the coating or by etching the pattern directly into the coating itself. Electromagnetic simulations showed that absorber-overlayer masks have superior imaging characteristics over etched masks (less sensitive to incident angles and pattern profiles). In an EUVL absorber overlayer mask, defects can occur in the mask substrate, reflective coating, and absorber pattern. Electromagnetic simulations showed that substrate defects cause the most severe image degradation. A printability study of substrate defects for absorber overlayer masks showed that printability of 25 nm high substrate defects are comparable to defects in optical lithography. Simulations also indicated that the manner in which the defects are covered by multilayer reflective coatings can affect printability. Coverage profiles that result in large lateral spreading of defect geometries amplify the printability of the defects by increasing their effective sizes. Coverage profiles of Mo/Si coatings deposited above defects were studied by atomic force microscopy and TEM. Results showed that lateral spread of defect geometry is proportional to height. Undercut at defect also increases the lateral spread. Reductions in defect heights were observed for 0.15 μm wide defect lines. A long-term study of Mo/Si coating reflectivity revealed that Mo/Si coatings with Mo as the top layer suffer significant reductions in reflectivity over time due to oxidation.

Specular Andreev reflection in thin films of topological insulators

Science.gov (United States)

Majidi, Leyla; Asgari, Reza

2016-05-01

We theoretically reveal the possibility of specular Andreev reflection in a thin film topological insulator normal-superconductor (N/S) junction in the presence of a gate electric field. The probability of specular Andreev reflection increases with the electric field, and electron-hole conversion with unit efficiency happens in a wide experimentally accessible range of the electric field. We show that perfect specular Andreev reflection can occur for all angles of incidence with a particular excitation energy value. In addition, we find that the thermal conductance of the structure displays exponential dependence on the temperature. Our results reveal the potential of the proposed topological insulator thin-film-based N/S structure for the realization of intraband specular Andreev reflection.

Normal incidence spectrophotometer using high density transmission grating technology and highly efficiency silicon photodiodes for absolute solar EUV irradiance measurements

Science.gov (United States)

Ogawa, H. S.; Mcmullin, D.; Judge, D. L.; Korde, R.

1992-01-01

New developments in transmission grating and photodiode technology now make it possible to realize spectrometers in the extreme ultraviolet (EUV) spectral region (wavelengths less than 1000 A) which are expected to be virtually constant in their diffraction and detector properties. Time dependent effects associated with reflection gratings are eliminated through the use of free standing transmission gratings. These gratings together with recently developed and highly stable EUV photodiodes have been utilized to construct a highly stable normal incidence spectrophotometer to monitor the variability and absolute intensity of the solar 304 A line. Owing to its low weight and compactness, such a spectrometer will be a valuable tool for providing absolute solar irradiance throughout the EUV. This novel instrument will also be useful for cross-calibrating other EUV flight instruments and will be flown on a series of Hitchhiker Shuttle Flights and on SOHO. A preliminary version of this instrument has been fabricated and characterized, and the results are described.

Orientation-dependent ion beam sputtering at normal incidence conditions in FeSiAl alloy

International Nuclear Information System (INIS)

Batic, Barbara Setina; Jenko, Monika

2010-01-01

The authors have performed Ar+ broad ion beam sputtering of a polycrystalline Fe-Si-Al alloy at normal incidence at energies varying from 6 to 10 keV. Sputtering results in the formation of etch pits, which can be classified in three shapes: triangular, rectangular, and square. As each grain of individual orientation exhibits a certain type of pattern, the etch pits were correlated with the crystal orientations by electron backscattered diffraction technique.

Transmission and total reflection of subhertz electromagnetic waves at the earth-atmosphere interface

International Nuclear Information System (INIS)

Shiozawa, Toshiyuki

2010-01-01

For the purpose of providing for a theoretical background for the study of electromagnetic fields generated by precursory effects of earthquakes, the problem of transmission and total reflection at the earth-atmosphere interface is investigated in detail for a subhertz plane electromagnetic wave incident from the earth's crust. The term ''subhertz'' means 'below 1 Hz'. First, for the special case of normal incidence, the overall power transmission coefficient at the earth-atmosphere interface is found to take a maximum value at a definite frequency f 0 which is inversely proportional to the square of the depth of a virtual hypocenter. A typical value of f 0 falls around 0.01 Hz. For oblique incidence as well, this feature of the overall power transmission coefficient is retained except in the vicinity of the critical angle of incidence for the H-wave. At the critical angle of incidence, the power flow carried by a surface wave along the interface becomes anomalously large for the H-wave. However, over a wide range of angles of incidence greater than the critical angle, the power flow carried by the E-wave exceeds that carried by the H-wave by orders of magnitude. Finally, the energy conservation relations for the incident, reflected, and transmitted waves at the earth-atmosphere interface are discussed. For an incident wave coming from the earth's crust, the interactive power between the incident and reflected waves plays a crucial role for the conservation of energy at the interface.

Integral particle reflection coefficient for oblique incidence of photons as universal function in the domain of initial energies up to 300 keV

Directory of Open Access Journals (Sweden)

Ljubenov Vladan L.

2014-01-01

Full Text Available In this paper we present the results of calculations and analyses of the integral particle reflection coefficient of photons for oblique photon incidence on planar targets, in the domain of initial photon energies from 100 keV to 300 keV. The results are based on the Monte Carlo simulations of the photon reflection from water, concrete, aluminum, iron, and copper materials, performed by the MCNP code. It has been observed that the integral particle reflection coefficient as a function of the ratio of total cross-section of photons and effective atomic number of target material shows universal behavior for all the analyzed shielding materials in the selected energy domain. Analytical formulas for different angles of photon incidence have been proposed, which describe the reflection of photons for all the materials and energies analyzed.

Theory of emission spectra from metal films irradiated by low energy electrons near normal incidence

International Nuclear Information System (INIS)

Kretschmann, E.; Callcott, T.A.; Arakawa, E.T.

1980-01-01

The emission spectrum produced by low energy electrons incident on a rough metal surface has been calculated for a roughness auto-correlation function containing a prominent peak at a high wave vector. For low energy electrons near normal incidence, the high wavevector peak dominates the roughness coupled surface plasmon radiation (RCSPR) process. The calculation yields estimates of the ratio of RCSPR to transition radiation, the dependence of emission intensity on electron energy and the shape and position of the RCSPR peak. The most interesting result is that the high-wavevector roughness can split the RCSPR radiation into peaks lying above and below the asymptotic surface plasma frequency. The results are compared with data from Ag in the following paper. (orig.)

Coupling of morphology to surface transport in ion-beam-irradiated surfaces: normal incidence and rotating targets

International Nuclear Information System (INIS)

Munoz-Garcia, Javier; Cuerno, Rodolfo; Castro, Mario

2009-01-01

Continuum models have proved their applicability to describe nanopatterns produced by ion-beam sputtering of amorphous or amorphizable targets at low and medium energies. Here we pursue the recently introduced 'hydrodynamic approach' in the cases of bombardment at normal incidence, or of oblique incidence onto rotating targets, known to lead to self-organized arrangements of nanodots. Our approach stresses the dynamical roles of material (defect) transport at the target surface and of local redeposition. By applying results previously derived for arbitrary angles of incidence, we derive effective evolution equations for these geometries of incidence, which are then numerically studied. Moreover, we show that within our model these equations are identical (albeit with different coefficients) in both cases, provided surface tension is isotropic in the target. We thus account for the common dynamics for both types of incidence conditions, namely formation of dots with short-range order and long-wavelength disorder, and an intermediate coarsening of dot features that improves the local order of the patterns. We provide for the first time approximate analytical predictions for the dependence of stationary dot features (amplitude and wavelength) on phenomenological parameters, that improve upon previous linear estimates. Finally, our theoretical results are discussed in terms of experimental data.

Radiation effects in silicon and gallium arsenide solar cells using isotropic and normally incident radiation

Science.gov (United States)

Anspaugh, B. E.; Downing, R. G.

1984-01-01

Several types of silicon and gallium arsenide solar cells were irradiated with protons with energies between 50 keV and 10 MeV at both normal and isotropic incidence. Damage coefficients for maximum power relative to 10 MeV were derived for these cells for both cases of omni-directional and normal incidence. The damage coefficients for the silicon cells were found to be somewhat lower than those quoted in the Solar Cell Radiation Handbook. These values were used to compute omni-directional damage coefficients suitable for solar cells protected by coverglasses of practical thickness, which in turn were used to compute solar cell degradation in two proton-dominated orbits. In spite of the difference in the low energy proton damage coefficients, the difference between the handbook prediction and the prediction using the newly derived values was negligible. Damage coefficients for GaAs solar cells for short circuit current, open circuit voltage, and maximum power were also computed relative to 10 MeV protons. They were used to predict cell degradation in the same two orbits and in a 5600 nmi orbit. Results show the performance of the GaAs solar cells in these orbits to be superior to that of the Si cells.

LROC WAC 100 Meter Scale Photometrically Normalized Map of the Moon

Science.gov (United States)

Boyd, A. K.; Nuno, R. G.; Robinson, M. S.; Denevi, B. W.; Hapke, B. W.

2013-12-01

The Lunar Reconnaissance Orbiter Camera (LROC) Wide Angle Camera (WAC) monthly global observations allowed derivation of a robust empirical photometric solution over a broad range of incidence, emission and phase (i, e, g) angles. Combining the WAC stereo-based GLD100 [1] digital terrain model (DTM) and LOLA polar DTMs [2] enabled precise topographic corrections to photometric angles. Over 100,000 WAC observations at 643 nm were calibrated to reflectance (I/F). Photometric angles (i, e, g), latitude, and longitude were calculated and stored for each WAC pixel. The 6-dimensional data set was then reduced to 3 dimensions by photometrically normalizing I/F with a global solution similar to [3]. The global solution was calculated from three 2°x2° tiles centered on (1°N, 147°E), (45°N, 147°E), and (89°N, 147°E), and included over 40 million WAC pixels. A least squares fit to a multivariate polynomial of degree 4 (f(i,e,g)) was performed, and the result was the starting point for a minimum search solving the non-linear function min[{1-[ I/F / f(i,e,g)] }2]. The input pixels were filtered to incidence angles (calculated from topography) shadowed pixels, and the output normalized I/F values were gridded into an equal-area map projection at 100 meters/pixel. At each grid location the median, standard deviation, and count of valid pixels were recorded. The normalized reflectance map is the result of the median of all normalized WAC pixels overlapping that specific 100-m grid cell. There are an average of 86 WAC normalized I/F estimates at each cell [3]. The resulting photometrically normalized mosaic provides the means to accurately compare I/F values for different regions on the Moon (see Nuno et al. [4]). The subtle differences in normalized I/F can now be traced across the local topography at regions that are illuminated at any point during the LRO mission (while the WAC was imaging), including at polar latitudes. This continuous map of reflectance at 643 nm

Bidirectional reflectance distribution function of Spectralon white reflectance standard illuminated by incoherent unpolarized and plane-polarized light.

Science.gov (United States)

Bhandari, Anak; Hamre, Børge; Frette, Øvynd; Zhao, Lu; Stamnes, Jakob J; Kildemo, Morten

2011-06-01

A Lambert surface would appear equally bright from all observation directions regardless of the illumination direction. However, the reflection from a randomly scattering object generally has directional variation, which can be described in terms of the bidirectional reflectance distribution function (BRDF). We measured the BRDF of a Spectralon white reflectance standard for incoherent illumination at 405 and 680 nm with unpolarized and plane-polarized light from different directions of incidence. Our measurements show deviations of the BRDF for the Spectralon white reflectance standard from that of a Lambertian reflector that depend both on the angle of incidence and the polarization states of the incident light and detected light. The non-Lambertian reflection characteristics were found to increase more toward the direction of specular reflection as the angle of incidence gets larger.

Visions of normality? Early experiences of radiographic reporting

Energy Technology Data Exchange (ETDEWEB)

Reeves, Pauline E-mail: pauline.reeves@whnt.nhs.uk

2004-08-01

This article reflects on my early [student] experiences in learning to undertake radiographic reporting and uses critical incidents to highlight two areas of error during this period. These errors include perceptual (optical illusions and, in particular, the Mach band effect) and lack of subject specific knowledge (specifically anatomical knowledge--especially of normal anatomical variants). These two errors are analysed in the wider context of radiological error and the difficulty in reaching consensus even between experienced reporters.

Visions of normality? Early experiences of radiographic reporting

International Nuclear Information System (INIS)

Reeves, Pauline

2004-01-01

This article reflects on my early [student] experiences in learning to undertake radiographic reporting and uses critical incidents to highlight two areas of error during this period. These errors include perceptual (optical illusions and, in particular, the Mach band effect) and lack of subject specific knowledge (specifically anatomical knowledge--especially of normal anatomical variants). These two errors are analysed in the wider context of radiological error and the difficulty in reaching consensus even between experienced reporters

Integrating an incident management system within a continuity of operations programme: case study of the Bank of Canada.

Science.gov (United States)

Loop, Carole

2013-01-01

Carrying out critical business functions without interruption requires a resilient and robust business continuity framework. By embedding an industry-standard incident management system within its business continuity structure, the Bank of Canada strengthened its response plan by enabling timely response to incidents while maintaining a strong focus on business continuity. A total programme approach, integrating the two disciplines, provided for enhanced recovery capabilities. While the value of an effective and efficient response organisation is clear, as demonstrated by emergency events around the world, incident response structures based on normal operating hierarchy can experience unique challenges. The internationally-recognised Incident Command System (ICS) model addresses these issues and reflects the five primary incident management functions, each contributing to the overall strength and effectiveness of the response organisation. The paper focuses on the Bank of Canada's successful implementation of the ICS model as its incident management and continuity of operations programmes evolved to reflect current best practices.

Energy Relations for Plane Waves Reflected from Moving Media

DEFF Research Database (Denmark)

Daly, P.; Gruenberg, Harry

1967-01-01

When a plane wave is obliquely incident from vacuum on a semi-infinite moving medium, the energy flow carried by the incident wave, is in general, not carried away by the reflected and transmitted waves. This is only the case when the medium velocity is parallel to its vacuum interface. Otherwise...... there is a net inflow or outflow of electromagnetic energy, which can be accounted for by the change of stored energy in the system, and the work done by the mechanical forces acting on the medium. A detailed energy balance is drawn up for two different media moving normal to their vacuum interfaces: (a...

Autofluorescence Imaging With Near-Infrared Excitation:Normalization by Reflectance to Reduce Signal From Choroidal Fluorophores

Science.gov (United States)

Cideciyan, Artur V.; Swider, Malgorzata; Jacobson, Samuel G.

2015-01-01

Purpose. We previously developed reduced-illuminance autofluorescence imaging (RAFI) methods involving near-infrared (NIR) excitation to image melanin-based fluorophores and short-wavelength (SW) excitation to image lipofuscin-based flurophores. Here, we propose to normalize NIR-RAFI in order to increase the relative contribution of retinal pigment epithelium (RPE) fluorophores. Methods. Retinal imaging was performed with a standard protocol holding system parameters invariant in healthy subjects and in patients. Normalized NIR-RAFI was derived by dividing NIR-RAFI signal by NIR reflectance point-by-point after image registration. Results. Regions of RPE atrophy in Stargardt disease, AMD, retinitis pigmentosa, choroideremia, and Leber congenital amaurosis as defined by low signal on SW-RAFI could correspond to a wide range of signal on NIR-RAFI depending on the contribution from the choroidal component. Retinal pigment epithelium atrophy tended to always correspond to high signal on NIR reflectance. Normalizing NIR-RAFI reduced the choroidal component of the signal in regions of atrophy. Quantitative evaluation of RPE atrophy area showed no significant differences between SW-RAFI and normalized NIR-RAFI. Conclusions. Imaging of RPE atrophy using lipofuscin-based AF imaging has become the gold standard. However, this technique involves bright SW lights that are uncomfortable and may accelerate the rate of disease progression in vulnerable retinas. The NIR-RAFI method developed here is a melanin-based alternative that is not absorbed by opsins and bisretinoid moieties, and is comfortable to view. Further development of this method may result in a nonmydriatic and comfortable imaging method to quantify RPE atrophy extent and its expansion rate. PMID:26024124

Self-reflection and self-transmission of pulsed radiation by laser-evaporated media

Science.gov (United States)

Furzikov, Nickolay P.

1991-05-01

Analysis of the known laser-induced evaporation (thermodestruction) model predicts the quasiperiodic oscillation of the effective absorption depth between its normal value and some minute quantity consisting of a part of the incident wavelength. This prediction explains the experimental data on the polymer laser ablation depth as well as the reflection transient drop of the laserdestructed aluminum.

Bragg reflection transmission filters for variable resolution monochromators

International Nuclear Information System (INIS)

Chapman, D.

1989-01-01

There are various methods for improving the angular and spectral resolution of monochromator and analyzer systems. The novel system described here, though limited to higher x-ray energies (>20keV), is based on a dynamical effect occurring on the transmitted beam with a thin perfect crystal plate set in the Bragg reflection case. In the case of Bragg reflection from a perfect crystal, the incident beam is rapidly attenuated as it penetrates the crystal in the range of reflection. This extinction length is of the order of microns. The attenuation length, which determines the amount of normal transmission through the plate is generally much longer. Thus, in the range of the Bragg reflection the attenuation of the transmitted beam can change by several orders of magnitude with a small change in energy or angle. This thin crystal plate cuts a notch in the transmitted beam with a width equal to its Darwin width, thus acting as a transmission filter. When used in a non-dispersive mode with other monochromator crystals, the filter when set at the Bragg angle will reflect the entire Darwin width of the incident beam and transmit the wings of the incident beam distribution. When the element is offset in angle by some fraction of the Darwin width, the filter becomes useful in adjusting the angular width of the transmitted beam and removing a wing. Used in pairs with a symmetric offset, the filters can be used to continuously adjust the intrinsic angular divergence of the beam with good wing reduction. Instances where such filters may be useful are in improving the angular resolution of a small angle scattering camera. These filters may be added to a Bonse-Hart camera with one pair on the incident beam to reduce the intrinsic beam divergence and a second pair on the analyzer arm to improve the analyzer resolution. 2 refs., 3 Figs

Shape from specular reflection in calibrated environments and the integration of spatial normal fields

KAUST Repository

Balzer, Jonathan

2011-09-01

Reflections of a scene in a mirror surface contain information on its shape. This information is accessible by measurement through an optical metrology technique called deflectometry. The result is a field of normal vectors to the unknown surface having the remarkable property that it equally changes in all spatial directions, unlike normal maps occurring, e.g., in Shape from Shading. Its integration into a zero-order reconstruction of the surface thus deserves special attention. We develop a novel algorithm for this purpose which is relatively straightforward to implement yet outperforms existing ones in terms of efficiency and robustness. Experimental results on synthetic and real data complement the theoretical discussion. © 2011 IEEE.

From Intensity Profile to Surface Normal: Photometric Stereo for Unknown Light Sources and Isotropic Reflectances.

Science.gov (United States)

Lu, Feng; Matsushita, Yasuyuki; Sato, Imari; Okabe, Takahiro; Sato, Yoichi

2015-10-01

We propose an uncalibrated photometric stereo method that works with general and unknown isotropic reflectances. Our method uses a pixel intensity profile, which is a sequence of radiance intensities recorded at a pixel under unknown varying directional illumination. We show that for general isotropic materials and uniformly distributed light directions, the geodesic distance between intensity profiles is linearly related to the angular difference of their corresponding surface normals, and that the intensity distribution of the intensity profile reveals reflectance properties. Based on these observations, we develop two methods for surface normal estimation; one for a general setting that uses only the recorded intensity profiles, the other for the case where a BRDF database is available while the exact BRDF of the target scene is still unknown. Quantitative and qualitative evaluations are conducted using both synthetic and real-world scenes, which show the state-of-the-art accuracy of smaller than 10 degree without using reference data and 5 degree with reference data for all 100 materials in MERL database.

Ultra-wideband reflective polarization converter based on anisotropic metasurface

International Nuclear Information System (INIS)

Wu Jia-Liang; Lin Bao-Qin; Da Xin-Yu

2016-01-01

In this paper, we propose an ultra-wideband reflective linear cross-polarization converter based on anisotropic metasurface. Its unit cell is composed of a square-shaped resonator with intersectant diagonal and metallic ground sheet separated by dielectric substrate. Simulated results show that the converter can generate resonances at four frequencies under normal incident electromagnetic (EM) wave, leading to the bandwidth expansion of cross-polarization reflection. For verification, the designed polarization converter is fabricated and measured. The measured and simulated results agree well with each other, showing that the fabricated converter can convert x - or y -polarized incident wave into its cross polarized wave in a frequency range from 7.57 GHz to 20.46 GHz with a relative bandwidth of 91.2%, and the polarization conversion efficiency is greater than 90%. The proposed polarization converter has a simple geometry but an ultra wideband compared with the published designs, and hence possesses potential applications in novel polarization-control devices. (paper)

Cervical cancer incidence after normal cytological sample in routine screening using SurePath, ThinPrep, and conventional cytology

DEFF Research Database (Denmark)

Rozemeijer, Kirsten; Naber, Steffie K; Penning, Corine

2017-01-01

of histo- and cytopathology in the Netherlands (PALGA), January 2000 to March 2013.Population Women with 5 924 474 normal screening samples (23 833 123 person years).Exposure Use of SurePath or ThinPrep versus conventional cytology as screening test.Main outcome measure 72 month cumulative incidence...

Continuum modeling of ion-beam eroded surfaces under normal incidence: Impact of stochastic fluctuations

International Nuclear Information System (INIS)

Dreimann, Karsten; Linz, Stefan J.

2010-01-01

Graphical abstract: Deterministic surface pattern (left) and its stochastic counterpart (right) arising in a stochastic damped Kuramoto-Sivashinsky equation that serves as a model equation for ion-beam eroded surfaces and is systematically investigated. - Abstract: Using a recently proposed field equation for the surface evolution of ion-beam eroded semiconductor target materials under normal incidence, we systematically explore the impact of additive stochastic fluctuations that are permanently present during the erosion process. Specifically, we investigate the dependence of the surface roughness, the underlying pattern forming properties and the bifurcation behavior on the strength of the fluctuations.

The Normal-incidence Vacuum-ultraviolet Spectrometer for the TJ-II and First Experimental Results

Energy Technology Data Exchange (ETDEWEB)

McCarthy, K.J.; Zurro, B.; Baciero, A.

2002-07-01

A normal-incidence spectrometer, operating in the extreme-ultraviolet and ultraviolet wavelength regions, has been commissioned for the TJ-II stellarator. The instrument has been custom built by McPherson, Chelmsford, MA, and has several unique features and accessories that are described here. The instrument and CCD detector has been tested and calibrated, and its performance evaluated, using spectral lines from glow discharges and a RF excited flow lamp. Finally, the first spectra collected with the instrument of TJ-II plasmas are presented and a preliminary estimation of an oxygen ion temperature is made. (Author) 23 refs.

The Normal-incidence Vacuum-ultraviolet Spectrometer for the TJ-II and First Experimental Results

International Nuclear Information System (INIS)

McCarthy, K. J.; Zurro, B.; Baciero, A.

2002-01-01

A normal-incidence spectrometer, operating in the extreme-ultraviolet and ultraviolet wavelength regions, has been commissioned for the TJ-II stellarator. The instrument has been custom built by McPherson, Chelmsford, MA, and has several unique features and accessories that are described here. The instrument and CCD detector has been tested and calibrated, and its performance evaluated, using spectral lines from glow discharges and a RF excited flow lamp. Finally, the first spectra collected with the instrument of TJ-II plasmas are presented and a preliminary estimation of an oxygen ion temperature is made. (Author) 23 refs

Superfluid {sup 3}He, a two-fluid system, with the normal-fluid dynamics dominated by Andreev reflection

Energy Technology Data Exchange (ETDEWEB)

Pickett, G. R., E-mail: g.pickett@lancaster.ac.uk [Lancaster University, Department of Physics (United Kingdom)

2014-12-15

As a specific offering towards his festschrift, we present a review the various properties of the excitation gas in superfluid {sup 3}He, which depend on Andreev reflection. This phenomenon dominates many of the properties of the normal fluid, especially at the lowest temperatures. We outline the ideas behind this dominance and describe a sample of the many experiments in this system which the operation of Andreev reflection has made possible, from temperature measurement, particle detection, vortex imaging to cosmological analogues.

Incidence of ascariasis in gastric carcinoma

Energy Technology Data Exchange (ETDEWEB)

Kim, Jong Woo; Rhee, Hak Song; Bahk, Yong Whee [St Mary' s Hospital Catholic Medical College, Seoul (Korea, Republic of)

1972-09-15

Prompted by the finding that the radiological incidence of small bowel ascariasis in the patient with gastric carcinoma was unexpectedly lower than the incidence in the normal population, a clinical study was performed to investigate possible relationship between gastric carcinoma and intestinal ascariasis. As a preliminary survey, we reviewed the radiological incidence of ascariasis in a total of 2,446 cases of upper GI series performed at the Department of Radiology, St Mary's Hospital Catholic Medical College. These included 1,573 normal subjects, 146 gastric carcinoma patients, 100 benign gastric ulcer and 249 duodenal ulcer patients and 378 other upper GI diseases. Following the preliminary study, a more accurate parasitologic study was conducted in another 578 normal subjects and 51 gastric carcinoma patients. The radiological incidences of ascaiasis in normal subjects and gastric carcinoma patients were 15.1% and 28.1%, respectively. The incidence of overall helminthiasis including ascaris lumbricoides, trichocephalus trichiurus and trichostrongyloides orientalis in normal subjects of the present series was 73.5%. This figure is virtually the same with 69.1% of the general population incidence reported by Kim, et al. (1971), but the incidence in gastric carcinoma patients was 94.1%. The high incidence pattern of overall helminthiasis in gastric carcinoma patients is, however, reversed as for as ascariasis is concerned. Thus, the incidence of ascariasis of gastric carcinoma patients was much lower than that of normal subjects (9.8% vs 19.4%). From the present observation, it is postulated that there can be some possible antagonistic relationship between evolution of gastric carcinoma and small bowel infestation of ascaris lumbricoides.

Incidence of ascariasis in gastric carcinoma

International Nuclear Information System (INIS)

Kim, Jong Woo; Rhee, Hak Song; Bahk, Yong Whee

1972-01-01

Prompted by the finding that the radiological incidence of small bowel ascariasis in the patient with gastric carcinoma was unexpectedly lower than the incidence in the normal population, a clinical study was performed to investigate possible relationship between gastric carcinoma and intestinal ascariasis. As a preliminary survey, we reviewed the radiological incidence of ascariasis in a total of 2,446 cases of upper GI series performed at the Department of Radiology, St Mary's Hospital Catholic Medical College. These included 1,573 normal subjects, 146 gastric carcinoma patients, 100 benign gastric ulcer and 249 duodenal ulcer patients and 378 other upper GI diseases. Following the preliminary study, a more accurate parasitologic study was conducted in another 578 normal subjects and 51 gastric carcinoma patients. The radiological incidences of ascaiasis in normal subjects and gastric carcinoma patients were 15.1% and 28.1%, respectively. The incidence of overall helminthiasis including ascaris lumbricoides, trichocephalus trichiurus and trichostrongyloides orientalis in normal subjects of the present series was 73.5%. This figure is virtually the same with 69.1% of the general population incidence reported by Kim, et al. (1971), but the incidence in gastric carcinoma patients was 94.1%. The high incidence pattern of overall helminthiasis in gastric carcinoma patients is, however, reversed as for as ascariasis is concerned. Thus, the incidence of ascariasis of gastric carcinoma patients was much lower than that of normal subjects (9.8% vs 19.4%). From the present observation, it is postulated that there can be some possible antagonistic relationship between evolution of gastric carcinoma and small bowel infestation of ascaris lumbricoides

Short-wavelength soft-x-ray laser pumped in double-pulse single-beam non-normal incidence

International Nuclear Information System (INIS)

Zimmer, D.; Ros, D.; Guilbaud, O.; Habib, J.; Kazamias, S.; Zielbauer, B.; Bagnoud, V.; Ecker, B.; Aurand, B.; Kuehl, T.; Hochhaus, D. C.; Neumayer, P.

2010-01-01

We demonstrated a 7.36 nm Ni-like samarium soft-x-ray laser, pumped by 36 J of a neodymium:glass chirped-pulse amplification laser. Double-pulse single-beam non-normal-incidence pumping was applied for efficient soft-x-ray laser generation. In this case, the applied technique included a single-optic focusing geometry for large beam diameters, a single-pass grating compressor, traveling-wave tuning capability, and an optimized high-energy laser double pulse. This scheme has the potential for even shorter-wavelength soft-x-ray laser pumping.

The role of random nanostructures for the omnidirectional anti-reflection properties of the glasswing butterfly

Science.gov (United States)

Siddique, Radwanul Hasan; Gomard, Guillaume; Hölscher, Hendrik

2015-04-01

The glasswing butterfly (Greta oto) has, as its name suggests, transparent wings with remarkable low haze and reflectance over the whole visible spectral range even for large view angles of 80°. This omnidirectional anti-reflection behaviour is caused by small nanopillars covering the transparent regions of its wings. In difference to other anti-reflection coatings found in nature, these pillars are irregularly arranged and feature a random height and width distribution. Here we simulate the optical properties with the effective medium theory and transfer matrix method and show that the random height distribution of pillars significantly reduces the reflection not only for normal incidence but also for high view angles.

Digital PIV Measurements of Acoustic Particle Displacements in a Normal Incidence Impedance Tube

Science.gov (United States)

Humphreys, William M., Jr.; Bartram, Scott M.; Parrott, Tony L.; Jones, Michael G.

1998-01-01

Acoustic particle displacements and velocities inside a normal incidence impedance tube have been successfully measured for a variety of pure tone sound fields using Digital Particle Image Velocimetry (DPIV). The DPIV system utilized two 600-mj Nd:YAG lasers to generate a double-pulsed light sheet synchronized with the sound field and used to illuminate a portion of the oscillatory flow inside the tube. A high resolution (1320 x 1035 pixel), 8-bit camera was used to capture double-exposed images of 2.7-micron hollow silicon dioxide tracer particles inside the tube. Classical spatial autocorrelation analysis techniques were used to ascertain the acoustic particle displacements and associated velocities for various sound field intensities and frequencies. The results show that particle displacements spanning a range of 1-60 microns can be measured for incident sound pressure levels of 100-130 dB and for frequencies spanning 500-1000 Hz. The ability to resolve 1 micron particle displacements at sound pressure levels in the 100 dB range allows the use of DPIV systems for measurement of sound fields at much lower sound pressure levels than had been previously possible. Representative impedance tube data as well as an uncertainty analysis for the measurements are presented.

Cumulative increased risk of incident type 2 diabetes mellitus with increasing triglyceride glucose index in normal-weight people: The Rural Chinese Cohort Study.

Science.gov (United States)

Zhang, Ming; Wang, Bingyuan; Liu, Yu; Sun, Xizhuo; Luo, Xinping; Wang, Chongjian; Li, Linlin; Zhang, Lu; Ren, Yongcheng; Zhao, Yang; Zhou, Junmei; Han, Chengyi; Zhao, Jingzhi; Hu, Dongsheng

2017-03-01

Risk of type 2 diabetes mellitus (T2DM) is increased in metabolically obese but normal-weight people. However, we have limited knowledge of how to prevent T2DM in normal-weight people. We aimed to evaluate the association between triglyceride glucose (TyG) index and incident T2DM among normal-weight people in rural China. We included data from 5706 people with normal body mass index (BMI) (18.5-23.9 kg/m 2 ) without baseline T2DM in a rural Chinese cohort followed for a median of 6.0 years. A Cox proportional-hazard model was used to assess the risk of incident T2DM by quartiles of TyG index and difference in TyG index between follow-up and baseline (TyG-D), estimating hazard ratios (HRs) and 95% confidence intervals (CIs). A generalized additive plot was used to show the nonparametric smoothed exposure-response association between risk of T2DM and TyG index as a continuous variable. TyG was calculated as ln [fasting triglyceride level (mg/dl) × fasting plasma glucose level (mg/dl)/2]. Risk of incident T2DM was increased with quartiles 2, 3 and 4 versus quartile 1 of TyG index (adjusted HR [aHR] 2.48 [95% CI 1.20-5.11], 3.77 [1.83-7.79], and 5.30 [2.21-12.71], P trend  index). Risk of incident T2DM was increased with quartile 4 versus quartile 1 of TyG-D (aHR 3.91 [2.22-6.87]). The results were consistent when analyses were restricted to participants without baseline metabolic syndrome and impaired fasting glucose level. The generalized additive plot showed cumulative increased risk of T2DM with increasing TyG index. Risk of incident T2DM is increased with increasing TyG index among rural Chinese people, so the index might be an important indicator for identifying people at high risk of T2DM.

Effect of retardation on the reflectance properties of the metallic Fibonacci quasi-superlattice

International Nuclear Information System (INIS)

Feng Weiguo; Yao Hesheng; Xu Xiang

1989-12-01

Based on the hydrodynamic model theory and the transfer matrix method, we have re-examined the reflection properties by taking account of the retardation effect to the system of the metallic Fibonacci quasi-superlattice. For the normal incident S-polarized Soft X-rays and extreme ultraviolet, we find that the self-similar reflecting spectrum will be restrained with the increasing of the retardation, but for the higher frequency region or at the smaller grazing angle, the self similarity will still exist for the lower generation quasi-superlattice. (author). 19 refs, 2 figs, 1 tab

The normalization of surface anisotropy effects present in SEVIRI reflectances by using the MODIS BRDF method

DEFF Research Database (Denmark)

Proud, Simon Richard; Zhang, Qingling; Schaaf, Crystal

2014-01-01

A modified version of the MODerate resolution Imaging Spectroradiometer (MODIS) bidirectional reflectance distribution function (BRDF) algorithm is presented for use in the angular normalization of surface reflectance data gathered by the Spinning Enhanced Visible and InfraRed Imager (SEVIRI...... acquisition period than the comparable MODIS products while, at the same time, removing many of the angular perturbations present within the original MSG data. The NBAR data are validated against reflectance data from the MODIS instrument and in situ data gathered at a field location in Africa throughout 2008....... It is found that the MSG retrievals are stable and are of high-quality across much of the SEVIRI disk while maintaining a higher temporal resolution than the MODIS BRDF products. However, a number of circumstances are discovered whereby the BRDF model is unable to function correctly with the SEVIRI...

Incidence angle normalization of radar backscatter data

Science.gov (United States)

NASA’s Soil Moisture Passive Active (SMAP) satellite (~2014) will include a radar system that will provide L-band multi-polarization backscatter at a constant incidence angle of 40º. During the pre-launch phase of the project there is a need for observations that will support the radar-based soil mo...

Assessment of Microcirculatory Hemoglobin Levels in Normal and Diabetic Subjects using Diffuse Reflectance Spectroscopy in the Visible Region — a Pilot Study

Science.gov (United States)

Sujatha, N.; Anand, B. S. Suresh; Nivetha, K. Bala; Narayanamurthy, V. B.; Seshadri, V.; Poddar, R.

2015-07-01

Light-based diagnostic techniques provide a minimally invasive way for selective biomarker estimation when tissues transform from a normal to a malignant state. Spectroscopic techniques based on diffuse reflectance characterize the changes in tissue hemoglobin/oxygenation levels during the tissue transformation process. Recent clinical investigations have shown that changes in tissue oxygenation and microcirculation are observed in diabetic subjects in the initial and progressive stages. In this pilot study, we discuss the potential of diffuse reflectance spectroscopy (DRS) in the visible (Vis) range to differentiate the skin microcirculatory hemoglobin levels between normal and advanced diabetic subjects with and without neuropathy. Average concentration of hemoglobin as well as hemoglobin oxygen saturation within the probed tissue volume is estimated for a total of four different sites in the foot sole. The results indicate a statistically significant decrease in average total hemoglobin and increase in hemoglobin oxygen saturation levels for diabetic foot compared with a normal foot. The present study demonstrates the ability of reflectance spectroscopy in the Vis range to determine and differentiate the changes in tissue hemoglobin and hemoglobin oxygen saturation levels in normal and diabetic subjects.

Particle reflection and TFTR neutral beam diagnostics

International Nuclear Information System (INIS)

Kamperschroer, J.H.; Grisham, L.R.; Kugel, H.W.; O'Connor, T.E.; Newman, R.A.; Stevenson, T.N.; von Halle, A.; Williams, M.D.

1992-04-01

Determination of two critical neutral beam parameters, power and divergence, are affected by the reflection of a fraction of the incident energy from the surface of the measuring calorimeter. On the TFTR Neutral Beam Test Stand, greater than 30% of the incident power directed at the target chamber calorimeter was unaccounted for. Most of this loss is believed due to reflection from the surface of the flat calorimeter, which was struck at a near grazing incidence (12 degrees). Beamline calorimeters, of a ''V''-shape design, while retaining the beam power, also suffer from reflection effects. Reflection, in this latter case, artificially peaks the power toward the apex of the ''V'', complicating the fitting technique, and increasing the power density on axis by 10 to 20%; an effect of import to future beamline designers. Agreement is found between measured and expected divergence values, even with 24% of the incident energy reflected

Soft X-ray images of the solar corona using normal incidence optics

Science.gov (United States)

Bruner, M. E.; Haisch, B. M.; Brown, W. A.; Acton, L. W.; Underwood, J. H.

1988-01-01

A solar coronal loop system has been photographed in soft X-rays using a normal incidence telescope based on multilayer mirror technology. The telescope consisted of a spherical objective mirror of 4 cm aperture and 1 m focal length, a film cassette, and a focal plane shutter. A metallized thin plastic film filter was used to exclude visible light. The objective mirror was covered with a multilayer coating consisting of alternating layers of tungsten and carbon whose combined thicknesses satisfied the Bragg diffraction condition for 44 A radiation. The image was recorded during a rocket flight on October 25, 1985 and was dominated by emission lines arising from the Si XII spectrum. The rocket also carried a high resolution soft X-ray spectrograph that confirmed the presence of Si XII line radiation in the source. This image represents the first successful use of multilayer technology for astrophysical observations.

X-ray photographs of a solar active region with a multilayer telescope at normal incidence

Science.gov (United States)

Underwood, J. H.; Bruner, M. E.; Haisch, B. M.; Brown, W. A.; Acton, L. W.

1987-01-01

An astronomical photograph was obtained with a multilayer X-ray telescope. A 4-cm tungsten-carbon multilayer mirror was flown as part of an experimental solar rocket payload, and successful images were taken of the sun at normal incidence at a wavelength of 44 A. Coronal Si XII emission from an active region was recorded on film; as expected, the structure is very similar to that observed at O VIII wavelengths by the Solar Maximum Mission flat-crystal spectrometer at the same time. The small, simple optical system used in this experiment appears to have achieved a resolution of 5 to 10 arcsec.

A finite element propagation model for extracting normal incidence impedance in nonprogressive acoustic wave fields

Science.gov (United States)

Watson, Willie R.; Jones, Michael G.; Tanner, Sharon E.; Parrott, Tony L.

1995-01-01

A propagation model method for extracting the normal incidence impedance of an acoustic material installed as a finite length segment in a wall of a duct carrying a nonprogressive wave field is presented. The method recasts the determination of the unknown impedance as the minimization of the normalized wall pressure error function. A finite element propagation model is combined with a coarse/fine grid impedance plane search technique to extract the impedance of the material. Results are presented for three different materials for which the impedance is known. For each material, the input data required for the prediction scheme was computed from modal theory and then contaminated by random error. The finite element method reproduces the known impedance of each material almost exactly for random errors typical of those found in many measurement environments. Thus, the method developed here provides a means for determining the impedance of materials in a nonprogressirve wave environment such as that usually encountered in a commercial aircraft engine and most laboratory settings.

Ultra-wideband reflective polarization converter based on anisotropic metasurface

Science.gov (United States)

Wu, Jia-Liang; Lin, Bao-Qin; Da, Xin-Yu

2016-08-01

In this paper, we propose an ultra-wideband reflective linear cross-polarization converter based on anisotropic metasurface. Its unit cell is composed of a square-shaped resonator with intersectant diagonal and metallic ground sheet separated by dielectric substrate. Simulated results show that the converter can generate resonances at four frequencies under normal incident electromagnetic (EM) wave, leading to the bandwidth expansion of cross-polarization reflection. For verification, the designed polarization converter is fabricated and measured. The measured and simulated results agree well with each other, showing that the fabricated converter can convert x- or y-polarized incident wave into its cross polarized wave in a frequency range from 7.57 GHz to 20.46 GHz with a relative bandwidth of 91.2%, and the polarization conversion efficiency is greater than 90%. The proposed polarization converter has a simple geometry but an ultra wideband compared with the published designs, and hence possesses potential applications in novel polarization-control devices. Project supported by the National Natural Science Foundation of China (Grant Nos. 61471387, 61271250, and 61571460).

Very high coronary artery calcium score with normal myocardial perfusion SPECT imaging is associated with a moderate incidence of severe coronary artery disease

Energy Technology Data Exchange (ETDEWEB)

Yuoness, Salem A.; Goha, Ahmed M.; Romsa, Jonathan G.; Akincioglu, Cigdem; Warrington, James C.; Datta, Sudip; Gambhir, Sanjay; Urbain, Jean-Luc C.; Vezina, William C. [London Health Sciences Centre, Department of Nuclear Medicine, London, ON (Canada); Massel, David R. [London Health Sciences Centre, Division of Cardiology, London, ON (Canada); Martell, Rafael [Private Practice, London, ON (Canada)

2015-09-15

Myocardial perfusion imaging (MPI) has limitations in the presence of balanced multivessel disease (MVD) and left main (LM) coronary artery disease, occasionally resulting in false-normal results despite the high cardiovascular risk associated with this condition. The purpose of this study was to assess the incidence of severe coronary artery disease (CAD) in the presence of a very high Agatston coronary artery calcium (CAC) score (>1,000) in stable symptomatic patients without known CAD but with normal MPI results. A total of 2,659 prospectively acquired consecutive patients were referred for MPI and evaluation of CAC score by CT. Of this patient population, 8 % (222/2,659) had ischemia without myocardial infarction (MI) on MPI and 11 % (298/2,659) had abnormal MPI (MI and/or ischemia). On presentation 1 % of the patients (26/2,659) were symptomatic, had a CAC score >1,000 and normal MPI results. The definition of normal MPI was strict and included a normal hemodynamic response without ischemic ECG changes and normal imaging, particularly absence of transient ischemic dilation. All of these 26 patients with a CAC score >1,000 and normal MPI findings underwent cardiac catheterization. Of these 26 patients, 58 % (15/26) had severe disease (≥70 % stenosis) leading to revascularization. Of this group, 47 % (7/15) underwent percutaneous intervention, and 53 % (8/15) underwent coronary artery bypass grafting. All of these 15 patients had either MVD (14/15) or LM coronary artery disease (1/15), and represented 0.6 % (15/2,659) of all referred patients (95 % CI 0.3 - 0.9 %). The majority, 90 % (8/9), had severe CAD with typical chest pain. A very high CAC score (>1,000) with normal MPI in a small subset of symptomatically stable patients was associated with a moderate incidence of severe CAD (95 % CI 37 - 77 %). Larger studies and/or a meta-analysis of small studies are needed to more precisely estimate the incidence of CAD in this population. This study also supports

Active isotropic slabs: conditions for amplified reflection

Science.gov (United States)

Perez, Liliana I.; Matteo, Claudia L.; Etcheverry, Javier; Duplaá, María Celeste

2012-12-01

We analyse in detail the necessary conditions to obtain amplified reflection (AR) in isotropic interfaces when a plane wave propagates from a transparent medium towards an active one. First, we demonstrate analytically that AR is not possible if a single interface is involved. Then, we study the conditions for AR in a very simple configuration: normal incidence on an active slab immersed in transparent media. Finally, we develop an analysis in the complex plane in order to establish a geometrical method that not only describes the behaviour of active slabs but also helps to simplify the calculus.

Active isotropic slabs: conditions for amplified reflection

International Nuclear Information System (INIS)

Perez, Liliana I; Duplaá, María Celeste; Matteo, Claudia L; Etcheverry, Javier

2012-01-01

We analyse in detail the necessary conditions to obtain amplified reflection (AR) in isotropic interfaces when a plane wave propagates from a transparent medium towards an active one. First, we demonstrate analytically that AR is not possible if a single interface is involved. Then, we study the conditions for AR in a very simple configuration: normal incidence on an active slab immersed in transparent media. Finally, we develop an analysis in the complex plane in order to establish a geometrical method that not only describes the behaviour of active slabs but also helps to simplify the calculus. (paper)

A comparative study on omnidirectional anti-reflection SiO2 nanostructure films coating by glancing angle deposition

Science.gov (United States)

Prachachet, R.; Samransuksamer, B.; Horprathum, M.; Eiamchai, P.; Limwichean, S.; Chananonnawathorn, C.; Lertvanithphol, T.; Muthitamongkol, P.; Boonruang, S.; Buranasiri, P.

2018-02-01

Fabricated omnidirectional anti-reflection nanostructure films as a one of the promising alternative solar cell applications have attracted enormous scientific and industrial research benefits to their broadband, effective over a wide range of incident angles, lithography-free and high-throughput process. Recently, the nanostructure SiO2 film was the most inclusive study on anti-reflection with omnidirectional and broadband characteristics. In this work, the three-dimensional silicon dioxide (SiO2) nanostructured thin film with different morphologies including vertical align, slant, spiral and thin films were fabricated by electron beam evaporation with glancing angle deposition (GLAD) on the glass slide and silicon wafer substrate. The morphological of the prepared samples were characterized by field-emission scanning electron microscope (FE-SEM) and high-resolution transmission electron microscope (HRTEM). The transmission, omnidirectional and birefringence property of the nanostructure SiO2 films were investigated by UV-Vis-NIR spectrophotometer and variable angle spectroscopic ellipsometer (VASE). The spectrophotometer measurement was performed at normal incident angle and a full spectral range of 200 - 2000 nm. The angle dependent transmission measurements were investigated by rotating the specimen, with incidence angle defined relative to the surface normal of the prepared samples. This study demonstrates that the obtained SiO2 nanostructure film coated on glass slide substrate exhibits a higher transmission was 93% at normal incident angle. In addition, transmission measurement in visible wavelength and wide incident angles -80 to 80 were increased in comparison with the SiO2 thin film and glass slide substrate due to the transition in the refractive index profile from air to the nanostructure layer that improve the antireflection characteristics. The results clearly showed the enhanced omnidirectional and broadband characteristic of the three dimensional Si

Detection of the specific binding on protein microarrays by oblique-incidence reflectivity difference method

International Nuclear Information System (INIS)

Lu, Heng; Wen, Juan; Wang, Xu; Yuan, Kun; Lu, Huibin; Zhou, Yueliang; Jin, Kuijuan; Yang, Guozhen; Li, Wei; Ruan, Kangcheng

2010-01-01

The specific binding between Cy5-labeled goat anti-mouse Immunoglobulin G (IgG) and mouse IgG with a concentration range from 625 to 10 4 µg ml −1 has been detected successfully by the oblique-incidence reflectivity difference (OI-RD) method in each procedure of microarray fabrication. The experimental data prove that the OI-RD method can be employed not only to distinguish the different concentrations in label-free fashion but also to detect the antibody–antigen capture. In addition, the differential treatment of the OI-RD signals can decrease the negative influences of glass slide as the microarray upholder. Therefore the OI-RD technique has promising applications for the label-free and high-throughput detection of protein microarrays

Determination of point of incidence for the case of reflection or refraction at spherical surface knowing two points lying on the ray.

Science.gov (United States)

Mikš, Antonín; Novák, Pavel

2017-09-01

The paper is focused on the problem of determination of the point of incidence of a light ray for the case of reflection or refraction at the spherical optical surface, assuming that two fixed points in space that the sought light ray should go through are given. The requirement is that one of these points lies on the incident ray and the other point on the reflected/refracted ray. Although at first glance it seems to be a simple problem, it will be shown that it has no simple analytical solution. The basic idea of the solution is given, and it is shown that the problem leads to a nonlinear equation in one variable. The roots of the resulting nonlinear equation can be found by numerical methods of mathematical optimization. The proposed methods were implemented in MATLAB, and the proper function of these algorithms was verified on several examples.

Reflection and transformation of acoustic waves at the interface in superfluid 3He-A

International Nuclear Information System (INIS)

Kekutiya, Sh.E.; Chkhaidze, N.D.

1997-01-01

Reflection and transformation of acoustic waves in 3 He-A and 3 He-A 1 are considered for two cases: (1) at the boundary with a solid impermeable wall at an arbitrary angle of incidence of a wave and (2) for normal incidence of waves on the interface between a free liquid and a system of periodic plane-parallel capillaries filling the semi-space. For the first case we have calculated the reflection coefficients of the first and the second sounds and spin and spin-temperature waves as well as the coefficients of transformation of these waves into each other. It is shown that the longitudinal wave undergoes no transformation into other waves, there occurs instead its complete reflection from the solid wall. The angle of incidence at which the energy attenuation coefficient of the first sound is maximum, and the interval of angles corresponding to the attenuation and the total interval reflection of the second sound are estimated. For the second case we have obtained: the coefficients of excitation of the fourth sound and the magneto-acoustic wave by the first and the second sounds; the reflection coefficients for the first and the second sounds and the longitudinal spin wave; the coefficient of transformation of the first sound into the second one and vice versa; the coefficient of reflection of the fourth sound from the capillary system - free liquid interface; the coefficient of excitation of longitudinal spin wave in free helium by the same wave in a capillary

A Numerical Theory for Impedance Education in Three-Dimensional Normal Incidence Tubes

Science.gov (United States)

Watson, Willie R.; Jones, Michael G.

2016-01-01

A method for educing the locally-reacting acoustic impedance of a test sample mounted in a 3-D normal incidence impedance tube is presented and validated. The unique feature of the method is that the excitation frequency (or duct geometry) may be such that high-order duct modes may exist. The method educes the impedance, iteratively, by minimizing an objective function consisting of the difference between the measured and numerically computed acoustic pressure at preselected measurement points in the duct. The method is validated on planar and high-order mode sources with data synthesized from exact mode theory. These data are then subjected to random jitter to simulate the effects of measurement uncertainties on the educed impedance spectrum. The primary conclusions of the study are 1) Without random jitter the method is in excellent agreement with that for known impedance samples, and 2) Random jitter that is compatible to that found in a typical experiment has minimal impact on the accuracy of the educed impedance.

Evolution of porous network in GaSb under normally incident 60 keV Ar{sup +}-ion irradiation

Energy Technology Data Exchange (ETDEWEB)

Datta, D.P. [SUNAG Laboratory, Institute of Physics, Bhubaneswar 751 005, Odisha (India); Kanjilal, A. [Department of Physics, Shiv Nadar University, Gautam Budh Nagar 203 207, Uttar Pradesh (India); Garg, S.K. [SUNAG Laboratory, Institute of Physics, Bhubaneswar 751 005, Odisha (India); Sahoo, P.K. [School of Physical Sciences, National Institute of Science Education and Research, Bhubaneswar 751 005, Odisha (India); Satpati, B. [Surface Physics and Material Science Division, Saha Institute of Nuclear Physics, 1/AF Bidhannagar, Kolkata 700 064 (India); Kanjilal, D. [Inter-University Accelerator Center, Aruna Asaf Ali Marg, New Delhi 110 067 (India); Som, T., E-mail: tsom@iopb.res.in [SUNAG Laboratory, Institute of Physics, Bhubaneswar 751 005, Odisha (India)

2014-08-15

Highlights: • We show the evolution of a nanoporous layer in GaSb under Ar{sup +}-ion bombardment at normal incidence in the hitherto unexplored high fluence regime, namely 7 × 10{sup 16}–3 × 10{sup 18} ions cm{sup −2}. • Fluence dependent formation and growth of patches on top of the nanoporous layer is demonstrated by scanning electron microscopy. • We also show high amount of oxidation of such ion-beam-generated nanoporous structures, with formation of Ga{sub 2}O{sub 3} and Sb{sub 2}O{sub 3}. • Our study reveals the presence of nanocrystallites within the porous layer even at the highest fluence used in the experiment. • We interpret the experimental observations through a qualitative model where we take into account the effect of re-deposition of atoms sputtered from the nanoporous layer during Ar{sup +}-ion irradiation of GaSb. - Abstract: GaSb(1 0 0) samples were irradiated with 60 keV Ar{sup +}-ions at normal incidence for fluences in the range of 7 × 10{sup 16} to 3 × 10{sup 18} ions cm{sup −2} at room temperature, showing gradual evolution of a porous surface layer containing interconnected nanofibers. In particular, fluence dependent formation of patches on the nanoporous layer is observed by scanning electron microscopy. Combined results of grazing incidence x-ray diffraction and transmission electron microscopy reveal the presence of nanocrystallites in the porous structures. Compositional analysis by x-ray photoelectron spectroscopy indicates the development of oxide phases, mainly Ga{sub 2}O{sub 3} and Sb{sub 2}O{sub 3} where the former increases with fluence. We have proposed a model addressing a competition between ion-induced-defect driven growth of the nanoporous layer and redeposition of sputtered target atoms on the growing layer.

Wave reflections from breakwaters

OpenAIRE

Dickson, William S.

1994-01-01

A new method is presented for estimating the reflection of a random, multi-directional sea from a coastal structure. The technique is applicable to an array of wave gauges of arbitrary geometry deployed seaward of the reflector. An expansion for small oblique wave incidence angles is used to derive an approximate relationship between measured array cross-spectra and a small number of parameters that describe the incident wave properties and the reflectivity of the structure. Model tests with ...

Comparison of conventional and total reflection excitation geometry for fluorescence X-ray absorption spectroscopy on droplet samples

International Nuclear Information System (INIS)

Falkenberg, G.; Pepponi, G.; Streli, C.; Wobrauschek, P.

2003-01-01

X-ray absorption fine structure (XAFS) experiments in fluorescence mode have been performed in total reflection excitation geometry and conventional 45 deg. /45 deg. excitation/detection geometry for comparison. The experimental results have shown that XAFS measurements are feasible under normal total reflection X-ray fluorescence (TXRF) conditions, i.e. on droplet samples, with excitation in grazing incidence and using a TXRF experimental chamber. The application of the total reflection excitation geometry for XAFS measurements increases the sensitivity compared to the conventional geometry leading to lower accessible concentration ranges. However, XAFS under total reflection excitation condition fails for highly concentrated samples because of the self-absorption effect

Grazing incidence polarized neutron scattering in reflection ...

Indian Academy of Sciences (India)

journal of. January 2012 physics pp. 1–58. Grazing incidence polarized ..... atomic distances, the neutron has an energy which is low compared to molecular binding ...... cores and that of the Co ions in the AF oxide coatings. ...... [32] C Leighton, M R Fitzsimmons, P Yashar, A Hoffmann, J Nogus, J Dura, C F Majkrzak and.

Experimental design for reflection measurements of highly reactive liquid or solid substances with application to liquid sodium

International Nuclear Information System (INIS)

Chan, S.H.; Gossler, A.A.

1980-01-01

A versatile goniometer system with associated electronic components and mechanical instruments has been assembled. It is designed to measure spectral, specular reflectances of highly reactive liquid or solid substances over a spectral range of 0.3 to 9 μ and incidence angles of 12 to 30 0 off the normal direction. The capability of measuring reflectances of liquid substances clearly distinguishes this experimental design from conventional systems which are applicable only to solid substances. This design has been used to measure the spectral, specular reflectance of liquid sodium and preliminary results obtained are compared with those of solid sodium measured by other investigators

Laser Incident Lessons Learned and Action List

Energy Technology Data Exchange (ETDEWEB)

Yarotski, Dmitry Anatolievitch [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-02-29

On Thursday November 19, 2015, LANL postdoc received an eye injury from a reflected, nonvisible laser beam (Class 4, pulsed, wavelength 800 nanometer). The setup is configured to split the laser output into two work areas in which qualified operators conduct research experiments. During this incident, the laser output beam was being projected to both experimental work areas, although only one experimental area was actively being used. The second laser beam directed to the second work area was blocked by an inappropriate device (Plexiglas, reflective, non-normal incidence) that reflected substantial portion of the beam toward the first setup. In preparation for the measurements, worker stepped on the stepstool and decided to remove the laser goggles to better see the micrometer readings which were difficult to see due to insufficient lighting. Immediately, he noticed a flash of light in his eye. The operator quickly replaced the laser eye-wear and then, using an infrared viewer, located a stray laser beam being reflected from the plexiglas beam block. The operator did not think he had sustained any injury and continued working. Later that day, however, he noticed a blurry spot in the vision of his left eye. He notified his supervisor on Friday morning, November 20, 2015, and was taken by CINT management to Sandia National Laboratories (SNL) medical facility for evaluation. SNL Medical did not find any abnormalities, but referred the operator to a local ophthalmologist for further evaluation. Further evaluations by the ophthalmologist on November 21 and November 23 identified a small spot of inflammation near the fovea on the retina in his left eye. The ophthalmologist stated that this spot would most likely heal on its own and that the blurry spot on the operator's vision would go away. A follow-up visit was scheduled. The employee was released back to work without restrictions.

Transient reflection and transmission of E polarized electromagnetic waves at boundary surface between air and moving isotropic plasma

International Nuclear Information System (INIS)

Saito, Yukimasa

1977-01-01

The transient reflection and transmission waves of E polarized electromagnetic waves coming into the boundary surface between air and moving isotropic plasma were theoretically investigated. By using the Laplace transformation in the moving system, the formulae of Lorentz and inverse Lorentz transformations concerning electromagnetic field were transformed, thus the transient reflection and transmission waves were obtained. These waves were normalized with the angular frequency of the incident waves, and the variation of the wave form was obtained. Examples of the numerical calculation of reflected waves are shown for the plasma moving in parallel to the boundary surface. (Kato, T.)

Numerical controlled diamond fly cutting machine for grazing incidence X-ray reflection mirrors

International Nuclear Information System (INIS)

Uchida, Fumihiko; Moriyama, Shigeo; Seya, Eiiti

1992-01-01

Synchrotron radiation has reached the stage of practical use, and the application to the wide fields that support future advanced technologies such as spectroscopy, the structural analysis of matters, semiconductor lithography and medical light source is expected. For the optical system of the equipment utilizing synchrotron radiation, the total reflection mirrors of oblique incidence are used for collimating and collecting X-ray. In order to restrain their optical aberration, nonspherical shape is required, and as the manufacturing method with high precision for nonspherical mirrors, a numerically controlled diamond cutting machine was developed. As for the cutting of soft metals with diamond tools, the high precision machining of any form can be done by numerical control, the machining time can be reduced as compared with grinding, and the cooling effect is large in metals. The construction of the cutting machine, the principle of machining, the control system, the method of calculating numerical control data, the investigation of machinable forms and the result of evaluation are reported. (K.I.)

Energy dependence of angular distributions of sputtered particles by ion-beam bombardment at normal incidence

International Nuclear Information System (INIS)

Matsuda, Yoshinobu; Ueda, Yasutoshi; Uchino, Kiichiro; Muraoka, Katsunori; Maeda, Mitsuo; Akazaki, Masanori; Yamamura, Yasunori.

1986-01-01

The angular distributions of sputtered Fe-atoms were measured using the laser fluorescence technique during Ar-ion bombardment for energies of 0.6, 1, 2 and 3 keV at normal incidence. The measured cosine distribution at 0.6 keV progressively deviated to an over-cosine distribution at higher energies, and at 3 keV the angular distribution was an overcosine distribution of about 20 %. The experimental results agree qualitatively with calculations by a recent computer simulation code, ACAT. The results are explained by the competition between surface scattering and the effects of primary knock-on atoms, which tend to make the angular distributions over-cosine and under-cosine, respectively. (author)

Theoretical calculations of the self-reflection coefficients for some species of ions

Energy Technology Data Exchange (ETDEWEB)

Luo, Z.M. E-mail: luozm@scu.edu.cn; Gou, C.; Hou, Q

2002-06-01

The bipartition model of ion transport has been applied to study the self-reflection coefficients of some species of ion beams which are normally incident to a surface. The computational results has been compared with the results taken from Eckstein and Biersack and the compilation data given by Thomas, Janev and Smith. It was found that there are in reasonable agreement between the results given by the bipartition model and the results given by Monte Carlo method.

Modeling Transmission and Reflection Mueller Matrices of Dielectric Half-Wave Plates

Science.gov (United States)

Salatino, Maria; de Bernardis, Paolo; Masi, Silvia

2017-02-01

We present a simple analytical model describing multiple reflections in dielectric and optically active waveplates, for both normal and slant incidence, including absorption. We compute from first principles the transmission and reflection Mueller matrices of the waveplate. The model is used to simulate the performance of a Stokes polarimeter for mm-waves, in the framework of current attempts to precisely measure the linear polarization of the Cosmic Microwave Background (CMB). We study the spectral response of these optical devices, taking into account band and angle averaging effects and confirm the presence of a much richer spectral dependence than in an ideal phase retarder. We also present the matrix elements for the reflection matrix, which is useful to estimate systematic effects in some polarimeter configurations. The formulas we have derived can be used to quickly simulate the performance of future CMB polarimeters.

The Normalization of Surface Anisotropy Effects Present in SEVIRI Reflectances by Using the MODIS BRDF Method

Science.gov (United States)

Proud, Simon Richard; Zhang, Qingling; Schaaf, Crystal; Fensholt, Rasmus; Rasmussen, Mads Olander; Shisanya, Chris; Mutero, Wycliffe; Mbow, Cheikh; Anyamba, Assaf; Pak, Ed;

Photometric normalization of LROC WAC images

Science.gov (United States)

Sato, H.; Denevi, B.; Robinson, M. S.; Hapke, B. W.; McEwen, A. S.; LROC Science Team

2010-12-01

The Lunar Reconnaissance Orbiter Camera (LROC) Wide Angle Camera (WAC) acquires near global coverage on a monthly basis. The WAC is a push frame sensor with a 90° field of view (FOV) in BW mode and 60° FOV in 7-color mode (320 nm to 689 nm). WAC images are acquired during each orbit in 10° latitude segments with cross track coverage of ~50 km. Before mosaicking, WAC images are radiometrically calibrated to remove instrumental artifacts and to convert at sensor radiance to I/F. Images are also photometrically normalized to common viewing and illumination angles (30° phase), a challenge due to the wide angle nature of the WAC where large differences in phase angle are observed in a single image line (±30°). During a single month the equatorial incidence angle drifts about 28° and over the course of ~1 year the lighting completes a 360° cycle. The light scattering properties of the lunar surface depend on incidence(i), emission(e), and phase(p) angles as well as soil properties such as single-scattering albedo and roughness that vary with terrain type and state of maturity [1]. We first tested a Lommel-Seeliger Correction (LSC) [cos(i)/(cos(i) + cos(e))] [2] with a phase function defined by an exponential decay plus 4th order polynomial term [3] which did not provide an adequate solution. Next we employed a LSC with an exponential 2nd order decay phase correction that was an improvement, but still exhibited unacceptable frame-to-frame residuals. In both cases we fitted the LSC I/F vs. phase angle to derive the phase corrections. To date, the best results are with a lunar-lambert function [4] with exponential 2nd order decay phase correction (LLEXP2) [(A1exp(B1p)+A2exp(B2p)+A3) * cos(i)/(cos(e) + cos(i)) + B3cos(i)]. We derived the parameters for the LLEXP2 from repeat imaging of a small region and then corrected that region with excellent results. When this correction was applied to the whole Moon the results were less than optimal - no surprise given the

Dual-band reflective polarization converter based on slotted wire resonators

Science.gov (United States)

Li, Fengxia; Zhang, Linbo; Zhou, Peiheng; Chen, Haiyan; Zhao, Rui; Zhou, Yang; Liang, Difei; Lu, Haipeng; Deng, Longjiang

2018-02-01

A dual-band and high-efficiency reflective linear polarization converter composed of a layer of slotted metal wires has been proposed. Both the simulated and experimental results indicate that the structure can convert a linearly polarized wave to its cross-polarized state for two distinct frequency bands under normal incidence: 9.8-15.1 and 19.2-25.7 GHz. This phenomenon is attributed to a resonance that corresponds to the "trapped mode" at 15.8 GHz. This mode is stable with structural parameters and incident angle at a relatively wide range, and thus becomes promising for dual-band (also multiband) devices design. By surface current distribution and electric field analysis, the operation mechanism has been illuminated, especially for the "trapped mode", identified by the equally but also oppositely directed currents in each unit cell.

Spectral reflectance properties of carbonaceous chondrites: 1. CI chondrites

Science.gov (United States)

Cloutis, E. A.; Hiroi, T.; Gaffey, M. J.; Alexander, C. M. O.'D.; Mann, P.

2011-03-01

Existing reflectance spectra of CI chondrites (18 spectra of 3 CIs) have been augmented with new (18 spectra of 2 CIs) reflectance spectra to ascertain the spectral variability of this meteorite class and provide insights into their spectral properties as a function of grain size, composition, particle packing, and viewing geometry. Particle packing and viewing geometry effects have not previously been examined for CI chondrites. The current analysis is focused on the 0.3-2.5 μm interval, as this region is available for the largest number of CI spectra. Reflectance spectra of powdered CI1 chondrites are uniformly dark (IOM), as no other CI opaque phase appears able to produce concurrent darkening and bluing. Magnetite can also explain the presence of an absorption feature near 1 μm in some CI spectra. The most blue-sloped spectra are generally associated with the larger grain size samples. For incidence and emission angles <60°, increasing phase angle results in darker and redder spectra, particularly below ∼1 μm. At high incidence angles (60°), increasing emission angle results in brighter and redder spectra. More densely packed samples and underdense (fluffed) samples show lower overall reflectance than normally packed and flat-surface powdered samples. Some B-class asteroids exhibit selected spectral properties consistent with CI chondrites, although perfect spectral matches have not been found. Because many CI chondrite spectra exhibit absorption features that can be related to specific mineral phases, the search for CI parent bodies can fruitfully be conducted using such parameters.

Biomimetic approaches to create anti-reflection glass surfaces for solar cells using self-organizing techniques

International Nuclear Information System (INIS)

Achtelik, J.; Sievers, W.; Lindner, J.K.N.

2013-01-01

Highlights: ► Nanostructured glass surfaces with theoretically near-to-zero reflectivity in the UVNIR region. ► Simple fabrication process using self-organization during reactive ion etching proposed. ► Prediction of optical reflectivity from AFM measured surface morphology. -- Abstract: Aiming to diminish the reflection losses of glass covered light harvesting devices, the optical reflectivity of nanostructured glass surfaces is studied theoretically and experimentally. The work is inspired by the nanoscale roughness of insect eyes, which is tried to be replicated on a technical glass surface. To this end, the reflectivity of glass surfaces with topographies represented by linear, parabolic and Fermi-shaped glass/air fill factor profiles is calculated for normal incidence. It is shown that using the latter ones, an almost complete suppression of reflections can be achieved. A simple, self-organization technique to create such Fermi-shaped filling factor profiles in glass experimentally is also presented

Biomimetic approaches to create anti-reflection glass surfaces for solar cells using self-organizing techniques

Energy Technology Data Exchange (ETDEWEB)

Achtelik, J.; Sievers, W. [University of Paderborn, Department of Physics, 33098 Paderborn (Germany); Center of Optoelectronics and Photonics Paderborn CeOPP, 33098 Paderborn (Germany); Lindner, J.K.N., E-mail: lindner@physik.uni-paderborn.de [University of Paderborn, Department of Physics, 33098 Paderborn (Germany); Center of Optoelectronics and Photonics Paderborn CeOPP, 33098 Paderborn (Germany)

2013-05-15

Highlights: ► Nanostructured glass surfaces with theoretically near-to-zero reflectivity in the UVNIR region. ► Simple fabrication process using self-organization during reactive ion etching proposed. ► Prediction of optical reflectivity from AFM measured surface morphology. -- Abstract: Aiming to diminish the reflection losses of glass covered light harvesting devices, the optical reflectivity of nanostructured glass surfaces is studied theoretically and experimentally. The work is inspired by the nanoscale roughness of insect eyes, which is tried to be replicated on a technical glass surface. To this end, the reflectivity of glass surfaces with topographies represented by linear, parabolic and Fermi-shaped glass/air fill factor profiles is calculated for normal incidence. It is shown that using the latter ones, an almost complete suppression of reflections can be achieved. A simple, self-organization technique to create such Fermi-shaped filling factor profiles in glass experimentally is also presented.

Simulation calculations of physical sputtering and reflection coefficient of plasma-irradiated carbon surface

International Nuclear Information System (INIS)

Kawamura, T.; Ono, T.; Yamamura, Y.

1994-08-01

Physical sputtering yields from the carbon surface irradiated by the boundary plasma are obtained with the use of a Monte Carlo simulation code ACAT. The yields are calculated for many random initial energy and angle values of incident protons or deuterons with a Maxwellian velocity distribution, and then averaged. Here the temperature of the boundary plasma, the sheath potential and the angle δ between the magnetic field line and the surface normal are taken into account. A new fitting formula for an arrangement of the numerical data of sputtering yield is introduced, in which six fitting parameters are determined from the numerical results and listed. These results provide a way to estimate the erosion of carbon materials irradiated by boundary plasma. The particle reflection coefficients for deuterons and their neutrals from a carbon surface are also calculated by the same code and presented together with, for comparison, that for the case of monoenergetic normal incidence. (author)

The impact of normal saline on the incidence of exposure keratopathy in patients hospitalized in intensive care units

Directory of Open Access Journals (Sweden)

Zohreh Davoodabady

2018-01-01

Full Text Available Background: Patients in the intensive care unit (ICU have impaired ocular protective mechanisms that lead to an increased risk of ocular surface diseases including exposure keratopathy (EK. This study was designed to evaluate the effect of normal saline (NS on the incidence and severity of EK in critically ill patients. Materials and Methods: This single-blind randomized controlled trial was conducted on 50 patients admitted to ICUs. The participants were selected through purposive sampling. One eye of each patient, randomly was allocated to intervention group (standard care with NS and the other eye to control group (standard care. In each patient, one eye (control group randomly received standard care and the other eye (intervention group received NS every 6 h in addition to standard care. The presence and severity of keratopathy was assessed daily until day 7 of hospitalization using fluorescein and an ophthalmoscope with cobalt blue filter. Chi-square test was used for statistical analysis in SPSS software. Results: Before the study ( first day there were no statistically significant differences in the incidence and severity of EK between groups. Although, the incidence and severity of EK after the study (7th day was higher in the intervention group compared to the control group, their differences were not statistically significant. Although, the incidence and severity of EK, from the 1st day until the 7th, increased within both groups, this increase was statistically significant only in the intervention (NS group. Conclusions: The use of NS as eye care in patients hospitalized in ICUs can increase the incidence and severity of EK and is not recommended.

Reflection of ion acoustic waves by the plasma sheath

International Nuclear Information System (INIS)

Ibrahim, I.; Kuehl, H.H.

1984-01-01

The reflection coefficient R for linear monochromatic ion acoustic waves incident on the transonic layer and sheath from the plasma interior is calculated. The treatment differs from previous analyses in that (1) the exact zero-order ion density and velocity profiles for a planar, bounded plasma are used, and the zero-order charge separation is not neglected, and (2) the first-order quantities near the transonic layer are considered in detail, including first-order charge separation, whereby it is found that no coupling to the beam modes exists, and that the functional form of the first-order solution is completely determined. It is shown that the upper bound for Vertical BarRVertical Bar is (1)/(3) . The largest reflection occurs for frequencies which are small compared with the ionization frequency, and generally decreases with increasing frequency. By Fourier superposition, the reflection of a pulse is computed. For a narrow incident pulse, the reflected pulse is greatly distorted and is small compared with the incident pulse. For a broad pulse, the reflected pulse is similar in shape to the incident pulse, and has a magnitude which is approximately (1)/(3) of the incident pulse

A transversely isotropic medium with a tilted symmetry axis normal to the reflector

KAUST Repository

Alkhalifah, Tariq Ali

2010-05-01

The computational tools for imaging in transversely isotropic media with tilted axes of symmetry (TTI) are complex and in most cases do not have an explicit closed-form representation. Developing such tools for a TTI medium with tilt constrained to be normal to the reflector dip (DTI) reduces their complexity and allows for closed-form representations. The homogeneous-case zero-offset migration in such a medium can be performed using an isotropic operator scaled by the velocity of the medium in the tilt direction. For the nonzero-offset case, the reflection angle is always equal to the incidence angle, and thus, the velocities for the source and receiver waves at the reflection point are equal and explicitly dependent on the reflection angle. This fact allows for the development of explicit representations for angle decomposition as well as moveout formulas for analysis of extended images obtained by wave-equation migration. Although setting the tilt normal to the reflector dip may not be valid everywhere (i.e., on salt flanks), it can be used in the process of velocity model building, in which such constrains are useful and typically are used. © 2010 Society of Exploration Geophysicists.

A transversely isotropic medium with a tilted symmetry axis normal to the reflector

KAUST Repository

Alkhalifah, Tariq Ali; Sava, Paul C.

2010-01-01

The computational tools for imaging in transversely isotropic media with tilted axes of symmetry (TTI) are complex and in most cases do not have an explicit closed-form representation. Developing such tools for a TTI medium with tilt constrained to be normal to the reflector dip (DTI) reduces their complexity and allows for closed-form representations. The homogeneous-case zero-offset migration in such a medium can be performed using an isotropic operator scaled by the velocity of the medium in the tilt direction. For the nonzero-offset case, the reflection angle is always equal to the incidence angle, and thus, the velocities for the source and receiver waves at the reflection point are equal and explicitly dependent on the reflection angle. This fact allows for the development of explicit representations for angle decomposition as well as moveout formulas for analysis of extended images obtained by wave-equation migration. Although setting the tilt normal to the reflector dip may not be valid everywhere (i.e., on salt flanks), it can be used in the process of velocity model building, in which such constrains are useful and typically are used. © 2010 Society of Exploration Geophysicists.

Natures and incidences of each normal variations on I.V.P. series of 1000 Korean females

International Nuclear Information System (INIS)

Shin, Ok Ja; Chin, Soo Yil

1980-01-01

Each organ of body has many normal variation and/or abnormal developments from fetus to adult, especially urogenital system is very complex and markedly abnormal. The authors attempt to analyze the natures, incidences and differences of each normal variations based on I.V.P. series of 1000 Korean females and the review of literatures were carried out. The results are as follows: 1. The normal variations of urinary tracts are about 30 kinds as follows; Aphasia 0/1000 (0%), Hypoplasia 4/1000 (0.4%), Atrophic kidney 0/1000 (0%), Hyperplasia 0/1000 (0%), Hypertrophied kidney 0/1000 (0%), Supernumerary kidney 0/1000 (0%), Pelvic kidney 0/1000 (0%), Wandering kidney 7/1000 (7%), Horseshoe kidney 2/1000 (2%), Nephroptosis 6/1000 (0.6%), Malroated kidney 0/1000 (0%), Crossed ecotopic kidney 0/1000 (0%), Ureteral kingking 440/1000 (44.0%), Short ureter 3/1000 (0.3%), Long ureter 49/1000 (4.9%), Retrocaval ureter 0/1000 (0%), Retroiliac ureter 0/1000 (0%), Mega-ureter 0/1000 (0%), Aberrant vessel in ureter 79/1000 (7.9%), Congenital ureteral valves 0/1000 (0%), Anomalous ureteral orifices 0/1000 (0%), Double ureter 22/1000 (2.2%), Ureteral diverticulum 0/1000 (0%), Extrarenal pelvis 170/1000 (17.0%), Intrarenal pelvis 830/1000 (83.0%), Supernumerary pelvis 55/1000 (55%), Renal backflow 2/1000 0.2%), Multiple calyces 0/1000 (0.1%), Calyceal diverticulum 2/1000 (0.2%), Unilateral fused kidney 0/1000 (0%), Polar enlarged kidney 0/1000 (0%). 2. The order of incidence of common variations in Korean females are as follows: 1. Intrarenal pelvis 2. Ureteral kingking 3. Extrarenal pelvis 4. Aberrant vessel in ureter 5. Double pelvis 6. Long ureter 7. Double ureter 8. Wandering Kidney 9. Nephrotosis 10. Hypoplasia 11. Short ureter 12. Horseshoe kidney 13. Renal backflow 14. Calyceal diverticulum 15. Supernumerary calyces. 3. The most common variations in Korean females are intrarenal pelvis, extrarenal pelvis, aberrant vessel in ureters and most of them are acquired origin. Contrary

Discriminating electromagnetic radiation based on angle of incidence

Science.gov (United States)

Hamam, Rafif E.; Bermel, Peter; Celanovic, Ivan; Soljacic, Marin; Yeng, Adrian Y. X.; Ghebrebrhan, Michael; Joannopoulos, John D.

2015-06-16

The present invention provides systems, articles, and methods for discriminating electromagnetic radiation based upon the angle of incidence of the electromagnetic radiation. In some cases, the materials and systems described herein can be capable of inhibiting reflection of electromagnetic radiation (e.g., the materials and systems can be capable of transmitting and/or absorbing electromagnetic radiation) within a given range of angles of incidence at a first incident surface, while substantially reflecting electromagnetic radiation outside the range of angles of incidence at a second incident surface (which can be the same as or different from the first incident surface). A photonic material comprising a plurality of periodically occurring separate domains can be used, in some cases, to selectively transmit and/or selectively absorb one portion of incoming electromagnetic radiation while reflecting another portion of incoming electromagnetic radiation, based upon the angle of incidence. In some embodiments, one domain of the photonic material can include an isotropic dielectric function, while another domain of the photonic material can include an anisotropic dielectric function. In some instances, one domain of the photonic material can include an isotropic magnetic permeability, while another domain of the photonic material can include an anisotropic magnetic permeability. In some embodiments, non-photonic materials (e.g., materials with relatively large scale features) can be used to selectively absorb incoming electromagnetic radiation based on angle of incidence.

Antarctic Surface Reflectivity Measurements from the ANITA-3 and HiCal-1 Experiments

Science.gov (United States)

Gorham, P. W.; Allison, P.; Banerjee, O.; Beatty, J. J.; Belov, K.; Besson, D. Z.; Binns, W. R.; Bugaev, V.; Cao, P.; Chen, C.; Chen, P.; Clem, J. M.; Connolly, A.; Dailey, B.; Dasgupta, P.; Deaconu, C.; Cremonesi, L.; Dowkontt, P. F.; Fox, B. D.; Gordon, J.; Hill, B.; Hupe, R.; Israel, M. H.; Jain, P.; Kowalski, J.; Lam, J.; Learned, J. G.; Liewer, K. M.; Liu, T. C.; Matsuno, S.; Miki, C.; Mottram, M.; Mulrey, K.; Nam, J.; Nichol, R. J.; Novikov, A.; Oberla, E.; Prohira, S.; Rauch, B. F.; Romero-Wolf, A.; Rotter, B.; Ratzlaff, K.; Russell, J.; Saltzberg, D.; Seckel, D.; Schoorlemmer, H.; Stafford, S.; Stockham, J.; Stockham, M.; Strutt, B.; Tatem, K.; Varner, G. S.; Vieregg, A. G.; Wissel, S. A.; Wu, F.; Young, R.

The primary science goal of the NASA-sponsored ANITA project is measurement of ultra-high energy neutrinos and cosmic rays, observed via radio-frequency signals resulting from a neutrino or cosmic ray interaction with terrestrial matter (e.g. atmospheric or ice molecules). Accurate inference of the energies of these cosmic rays requires understanding the transmission/reflection of radio wave signals across the ice-air boundary. Satellite-based measurements of Antarctic surface reflectivity, using a co-located transmitter and receiver, have been performed more-or-less continuously for the last few decades. Our comparison of four different reflectivity surveys, at frequencies ranging from 2 to 45GHz and at near-normal incidence, yield generally consistent maps of high versus low reflectivity, as a function of location, across Antarctica. Using the Sun as an RF source, and the ANITA-3 balloon borne radio-frequency antenna array as the RF receiver, we have also measured the surface reflectivity over the interval 200-1000MHz, at elevation angles of 12-30∘. Consistent with our previous measurement using ANITA-2, we find good agreement, within systematic errors (dominated by antenna beam width uncertainties) and across Antarctica, with the expected reflectivity as prescribed by the Fresnel equations. To probe low incidence angles, inaccessible to the Antarctic Solar technique and not probed by previous satellite surveys, a novel experimental approach (“HiCal-1”) was devised. Unlike previous measurements, HiCal-ANITA constitute a bi-static transmitter-receiver pair separated by hundreds of kilometers. Data taken with HiCal, between 200 and 600MHz shows a significant departure from the Fresnel equations, constant with frequency over that band, with the deficit increasing with obliquity of incidence, which we attribute to the combined effects of possible surface roughness, surface grain effects, radar clutter and/or shadowing of the reflection zone due to Earth

Chlorophyll fluorescence, photochemical reflective index and normalized difference vegetative index during plant senescence.

Science.gov (United States)

Cordon, Gabriela; Lagorio, M Gabriela; Paruelo, José M

2016-07-20

The relationship between the Photochemical Reflectance Index (PRI), Normalized Difference Vegetation Index (NDVI) and chlorophyll fluorescence along senescence was investigated in this work. Reflectance and radiance measurements were performed at canopy level in grass species presenting different photosynthetic metabolism: Avena sativa (C3) and Setaria italica (C4), at different stages of the natural senescence process. Sun induced-chlorophyll fluorescence at 760nm (SIF 760 ) and the apparent fluorescence yield (SIF 760 /a, with a=irradiance at time of measurement) were extracted from the radiance spectra of canopies using the Fraunhofer Line Discrimination-method. The photosynthetic parameters derived from Kautsky kinetics and pigment content were also calculated at leaf level. Whilst stand level NDVI patterns were related to changes in the structure of canopies and not in pigment content, stand level PRI patterns suggested changes both in terms of canopy and of pigment content in leaves. Both SIF 760 /a and Φ PSII decreased progressively along senescence in both species. A strong increment in NPQ was evident in A. sativa while in S. italica NPQ values were lower. Our most important finding was that two chlorophyll fluorescence signals, Φ PSII and SIF 760 /a, correlated with the canopy PRI values in the two grasses assessed, even when tissues at different ontogenic stages were present. Even though significant changes occurred in the Total Chlr/Car ratio along senescence in both studied species, significant correlations between PRI and chlorophyll fluorescence signals might indicate the usefulness of this reflectance index as a proxy of photosynthetic RUE, at least under the conditions of this study. The relationships between stand level PRI and the fluorescence estimators (Φ PSII and SIF 760 /a) were positive in both cases. Therefore, an increase in PRI values as in the fluorescence parameters would indicate higher RUE. Copyright © 2016 Elsevier GmbH. All

How Can Polarization States of Reflected Light from Snow Surfaces Inform Us on Surface Normals and Ultimately Snow Grain Size Measurements?

Science.gov (United States)

Schneider, A. M.; Flanner, M.; Yang, P.; Yi, B.; Huang, X.; Feldman, D.

2016-12-01

The Snow Grain Size and Pollution (SGSP) algorithm is a method applied to Moderate Resolution Imaging Spectroradiometer data to estimate snow grain size from space-borne measurements. Previous studies validate and quantify potential sources of error in this method, but because it assumes flat snow surfaces, however, large scale variations in surface normals can cause biases in its estimates due to its dependence on solar and observation zenith angles. To address these variations, we apply the Monte Carlo method for photon transport using data containing the single scattering properties of different ice crystals to calculate polarization states of reflected monochromatic light at 1500nm from modeled snow surfaces. We evaluate the dependence of these polarization states on solar and observation geometry at 1500nm because multiple scattering is generally a mechanism for depolarization and the ice crystals are relatively absorptive at this wavelength. Using 1500nm thus results in a higher number of reflected photons undergoing fewer scattering events, increasing the likelihood of reflected light having higher degrees of polarization. In evaluating the validity of the model, we find agreement with previous studies pertaining to near-infrared spectral directional hemispherical reflectance (i.e. black-sky albedo) and similarities in measured bidirectional reflectance factors, but few studies exist modeling polarization states of reflected light from snow surfaces. Here, we present novel results pertaining to calculated polarization states and compare dependences on solar and observation geometry for different idealized snow surfaces. If these dependencies are consistent across different ice particle shapes and sizes, then these findings could inform the SGSP algorithm by providing useful relationships between measurable physical quantities and solar and observation geometry to better understand variations in snow surface normals from remote sensing observations.

Angular distribution of diffuse reflectance from incoherent multiple scattering in turbid media.

Science.gov (United States)

Gao, M; Huang, X; Yang, P; Kattawar, G W

2013-08-20

The angular distribution of diffuse reflection is elucidated with greater understanding by studying a homogeneous turbid medium. We modeled the medium as an infinite slab and studied the reflection dependence on the following three parameters: the incident direction, optical depth, and asymmetry factor. The diffuse reflection is produced by incoherent multiple scattering and is solved through radiative transfer theory. At large optical depths, the angular distribution of the diffuse reflection with small incident angles is similar to that of a Lambertian surface, but, with incident angles larger than 60°, the angular distributions have a prominent reflection peak around the specular reflection angle. These reflection peaks are found originating from the scattering within one transport mean free path in the top layer of the medium. The maximum reflection angles for different incident angles are analyzed and can characterize the structure of angular distributions for different asymmetry factors and optical depths. The properties of the angular distribution can be applied to more complex systems for a better understanding of diffuse reflection.

Total reflection coefficients of low-energy photons presented as universal functions

Directory of Open Access Journals (Sweden)

Ljubenov Vladan

2010-01-01

Full Text Available The possibility of expressing the total particle and energy reflection coefficients of low-energy photons in the form of universal functions valid for different shielding materials is investigated in this paper. The analysis is based on the results of Monte Carlo simulations of photon reflection by using MCNP, FOTELP, and PENELOPE codes. The normal incidence of the narrow monoenergetic photon beam of the unit intensity and of initial energies from 20 keV up to 100 keV is considered, and particle and energy reflection coefficients from the plane homogenous targets of water, aluminum, and iron are determined and compared. The representations of albedo coefficients on the initial photon energy, on the probability of large-angle photon scattering, and on the mean number of photon scatterings are examined. It is found out that only the rescaled albedo coefficients dependent on the mean number of photon scatterings have the form of universal functions and these functions are determined by applying the least square method.

Reflection of 32--2000 eV deuterium from carbon

International Nuclear Information System (INIS)

Braun, M.; Thomas, E.W.

1982-01-01

Reflection of deuterium from carbon is measured by a technique based on the rise of partial pressure caused by the reflected particles. Data are presented for 32--2000 eV per deuteron incident energies and as a function of angle of incidence. The data are consistent with previous determinations at energies above 1000 eV. A systematic difference in energy dependence is found when the measurements for reflection of deuterium are compared on a reduced energy scale with MARLOWE computer simulations of hydrogen reflection

Photoelectron Yield and Photon Reflectivity from Candidate LHC Vacuum Chamber Materials with Implications to the Vacuum Chamber Design

CERN Document Server

Baglin, V; Gröbner, Oswald

1998-01-01

Studies of the photoelectron yield and photon reflectivity at grazing incidence (11 mrad) from candidate LHC vacuum chamber materials have been made on a dedicated beam line on the Electron Positron A ccumulator (EPA) ring at CERN. These measurements provide realistic input toward a better understanding of the electron cloud phenomena expected in the LHC. The measurements were made using synchrotro n radiation with critical photon energies of 194 eV and 45 eV; the latter corresponding to that of the LHC at the design energy of 7 TeV. The test materials are mainly copper, either, i) coated by co- lamination or by electroplating onto stainless steel, or ii) bulk copper prepared by special machining. The key parameters explored were the effect of surface roughness on the reflectivity and the pho toelectron yield at grazing photon incidence, and the effect of magnetic field direction on the yields measured at normal photon incidence. The implications of the results on the electron cloud phenom ena, and thus the L...

Angle-resolved reflection spectroscopy of high-quality PMMA opal crystal

Science.gov (United States)

Nemtsev, Ivan V.; Tambasov, Igor A.; Ivanenko, Alexander A.; Zyryanov, Victor Ya.

2018-02-01

PMMA opal crystal was prepared by a simple hybrid method, which includes sedimentation, meniscus formation and evaporation. We investigated three surfaces of this crystal by angle-resolved reflective light spectroscopy and SEM study. The angle-resolved reflective measurements were carried out in the 400-1100 nm range. We have determined the high-quality ordered surface of the crystal region. Narrow particle size distribution of the surface has been revealed. The average particle diameter obtained with SEM was nearly 361 nm. The most interesting result was that reflectivity of the surface turned out up to 98% at normal light incidence. Using a fit of dependences of the maximum reflectivity wavelength from an angle based on the Bragg-Snell law, the wavelength of maximum 0° reflectivity, the particle diameter and the fill factor have been determined. For the best surface maximum reflectivity wavelength of a 0° angle was estimated to be 869 nm. The particle diameter and fill factor were calculated as 372 nm and 0.8715, respectively. The diameter obtained by fitting is in excellent agreement with the particle diameter obtained with SEM. The reflectivity maximum is assumed to increase significantly when increasing the fill factor. We believe that using our simple approach to manufacture PMMA opal crystals will significantly increase the fabrication of high-quality photonic crystal templates and thin films.

The optical constants and spectral specular reflectivity of highly oriented pyrolytic graphite (HOPG)

International Nuclear Information System (INIS)

Havstad, M.A.; Schildbach, M.A.; McLean, W. II.

1993-08-01

Measurements of the specular reflectivity and the optical constants of highly ordered pyrolytic graphite (HOPG) have been made using two independent optical systems. The first measures reflectance (at 1.06 μm and 293 K) by comparing the intensity of a laser beam before and after reflecting off the sample. The second determines the complex index of raft-action (from 0.55 to 8.45 μm, with sample temperatures of 293, 480, 900 and 1300 K) by ellipsometry. Agreement between the two methods is good. Moderate reflectivities are observed over the full spectral range of measurement: the spectral directional-hemispherical reflectivity at normal incidence varies from 0.41 at 0.55 μm to 0.74 at 8.45 μm. The components of the complex index of refraction increase smoothly with wavelength. The index of refraction increases from 3.10 at 0.55 μm to 7.84 at 8.45 μm. The extinction coefficient varies from 2.01 to 6.66 over the same range

Release path temperatures of shock-compressed tin from dynamic reflectance and radiance measurements

Energy Technology Data Exchange (ETDEWEB)

La Lone, B. M., E-mail: lalonebm@nv.doe.gov; Stevens, G. D.; Turley, W. D. [National Security Technologies, LLC, Special Technologies Laboratory, Santa Barbara, California 93111 (United States); Holtkamp, D. B. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Iverson, A. J. [National Security Technologies, LLC, Los Alamos Operations, Los Alamos, New Mexico 87544 (United States); Hixson, R. S.; Veeser, L. R. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); National Security Technologies, LLC, Los Alamos Operations, Los Alamos, New Mexico 87544 (United States)

2013-08-14

Dynamic reflectance and radiance measurements were conducted for tin samples shock compressed to 35 GPa and released to 15 GPa using high explosives. We determined the reflectance of the tin samples glued to lithium fluoride windows using an integrating sphere with an internal xenon flashlamp as an illumination source. The dynamic reflectance (R) was determined at near normal incidence in four spectral bands with coverage in visible and near-infrared spectra. Uncertainties in R/R{sub 0} are <2%, and uncertainties in absolute reflectance are <5%. In complementary experiments, thermal radiance from the tin/glue/lithium fluoride interface was recorded with similar shock stress and spectral coverage as the reflectance measurements. The two sets of experiments were combined to obtain the temperature history of the tin surface with an uncertainty of <2%. The stress at the interface was determined from photonic Doppler velocimetry and combined with the temperatures to obtain temperature-stress release paths for tin. We discuss the relationship between the experimental release paths and release isentropes that begin on the principal shock Hugoniot.

Incidence and Antimicrobial Sensitivity Profiles of Normal Conjunctiva Bacterial Flora in the Central Area of China: A Hospital-Based Study

Directory of Open Access Journals (Sweden)

Hua Tao

2017-05-01

Full Text Available Objective: To study the distribution and patterns of resistance to antimicrobial agents of normal conjunctival bacteria.Materials and Methods: Conjunctival specimens were collected from 8,224 patients and then cultured, which underwent antimicrobial susceptibility test following standard methods. Patients with infectious symptoms such as erythema or oedema and those using systemic or topical antibiotics within 1 month were excluded.Results: In this study, the incidence of isolated bacteria was 24.2%. The middle aged group of 41–65 years presented the lowest rate of bacterial isolation which was 19.4%, while the highest isolation rate (83.1% was found in patients in the age range of 0–6 years. In every age group, the incidence of bacterial isolation in men was higher than that in women. The top 3 most commonly isolated micro-organisms were Staphylococcus epidermidis (39.7%, Streptococcus pneumoniae (4.5%, and Staphylococcus aureus (2.7%, of which about 83.1% S. aureus were isolated in the group of 0-6 years. We found that coagulase-negative Staphylococcus (CONS were more resistant to penicillin, macrolides, clindamycin and sulfonamides with the rate ranging from 57.9 to 90.8%, which were highly susceptible to vancomycin, linezolid, rifampin, tetracyclines, and aminoglycosides. Contrasting to CONS, the general resistance rate of S. aureus was significantly lower. Additionally, Streptococcus was susceptible well to the majority of antimicrobial agents, while highly resistant to macrolides and tetracyclines with the rate >80%.Conclusions: In conclusion, our study revealed the incidence and antimicrobial sensitivity profiles of normal conjunctiva bacterial flora in the central area of China, which could be useful in the prevention of ocular infections. Importantly, our data could be used to guide the selection of appropriate prophylactic agents.

Amyloid burden and incident depressive symptoms in cognitively normal older adults.

Science.gov (United States)

Harrington, Karra D; Gould, Emma; Lim, Yen Ying; Ames, David; Pietrzak, Robert H; Rembach, Alan; Rainey-Smith, Stephanie; Martins, Ralph N; Salvado, Olivier; Villemagne, Victor L; Rowe, Christopher C; Masters, Colin L; Maruff, Paul

2017-04-01

Several studies have reported that non-demented older adults with clinical depression show changes in amyloid-β (Aβ) levels in blood, cerebrospinal fluid and on neuroimaging that are consistent with those observed in patients with Alzheimer's disease. These findings suggest that Aβ may be one of the mechanisms underlying the relation between the two conditions. We sought to determine the relation between elevated cerebral Aβ and the presence of depression across a 54-month prospective observation period. Cognitively normal older adults from the Australian Imaging Biomarkers and Lifestyle study who were not depressed and had undergone a positron emission tomography scan to classify them as either high Aβ (n = 81) or low Aβ (n = 278) participated. Depressive symptoms were assessed using the Geriatric Depression Scale - Short Form at 18-month intervals over 54 months. Whilst there was no difference in probable depression between groups at baseline, incidence was 4.5 (95% confidence interval [CI] 1.3-16.4) times greater within the high Aβ group (9%) than the low Aβ group (2%) by the 54-month assessment. Results of this study suggest that elevated Aβ levels are associated with a 4.5-fold increased likelihood of developing clinically significant depressive symptoms on follow-up in preclinical Alzheimer's disease. This underscores the importance of assessing, monitoring and treating depressive symptoms in older adults with elevated Aβ. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Quadratic soliton self-reflection at a quadratically nonlinear interface

Science.gov (United States)

Jankovic, Ladislav; Kim, Hongki; Stegeman, George; Carrasco, Silvia; Torner, Lluis; Katz, Mordechai

2003-11-01

The reflection of bulk quadratic solutions incident onto a quadratically nonlinear interface in periodically poled potassium titanyl phosphate was observed. The interface consisted of the boundary between two quasi-phase-matched regions displaced from each other by a half-period. At high intensities and small angles of incidence the soliton is reflected.

Experimental design for reflection measurements of highly reactive liquid or solid substances with application to liquid sodium

International Nuclear Information System (INIS)

Chan, S.H.; Gossler, A.A.

1980-01-01

This technical report describes the experimental part of a program on thermal radiation properties of reactor materials. A versatile goniometer system with associated electronic components and mechanical instruments has been assembled. It is designed to measure spectral, specular reflectances of highly reactive liquid or solid substances over a spectral range of 0.3 μ to 9 μ and incidence angles of 12 0 to 30 0 off the normal direction. The capability of measuring reflectances of liquid substances clearly distinguishes this experimental design from conventional systems which are applicable only to solid substances. This design has been used to measure the spectral, specular reflectance of liquid sodium and preliminary results obtained are compared with those of solid sodium measured by other investigators

Energy reflection coefficient for H+ ions at energies between 10 and 80 keV

International Nuclear Information System (INIS)

Chen, C.K.; Bohdansky, J.; Eckstein, W.; Robinson, M.T.

1984-04-01

The energy reflection coefficient for H + ions at energies between 10 keV and 80 keV was determined by experiments and by computer calculations. Measurements were made with graphite, Al, Cu, Mo and W. targets. The angle of ion incidence was restricted to 85 0 , 78 0 and 70 0 measured from the surface normal. Calculated data were obtained by two different Monte Carlo computer programs (MARLOWE, TRIM). It was found that both the calculated and the measured data scale with the parameter epsilon cos 2 α, where epsilon is Lindhard's reduced energy and α the angle of incidence for the ions. The measured values are smaller than those calculated. This can be explained by surface roughness which developed during the ion irradiation

Monte Carlo simulation of light reflection from cosmetic powders on the skin

Science.gov (United States)

Okamoto, Takashi; Motoda, Masafumi; Igarashi, Takanori; Nakao, Keisuke

2011-07-01

The reflection and scattering properties of light incident on skin covered with powder particles have been investigated. A three-layer skin structure with a spot is modeled, and the propagation of light in the skin and the scattering of light by particles on the skin surface are simulated by means of a Monte Carlo method. Under the condition in which only single scattering of light occurs in the powder layer, the reflection spectra of light from the skin change dramatically with the size of powder particles. The color difference between normal skin and spots is found to diminish more when powder particles smaller than the wavelength of light are used. It is shown that particle polydispersity suppresses substantially the extreme spectral change caused by monodisperse particles with a size comparable to the light wavelength.

Determination of continuous complex refractive index dispersion of biotissue based on internal reflection

Science.gov (United States)

Deng, Zhichao; Wang, Jin; Ye, Qing; Sun, Tengqian; Zhou, Wenyuan; Mei, Jianchun; Zhang, Chunping; Tian, Jianguo

2016-01-01

The complex refractive index dispersion (CRID), which contains the information on the refractive index dispersion and extinction coefficient spectra, is an important optical parameter of biotissue. However, it is hard to perform the CRID measurement on biotissues due to their high scattering property. Continuous CRID measurement based on internal reflection (CCRIDM-IR) is introduced. By using a lab-made apparatus, internal reflectance spectra of biotissue samples at multiple incident angles were detected, from which the continuous CRIDs were calculated based on the Fresnel formula. Results showed that in 400- to 750-nm range, hemoglobin solution has complicated dispersion and extinction coefficient spectra, while other biotissues have normal dispersion properties, and their extinction coefficients do not vary much with different wavelengths. The normal dispersion can be accurately described by several coefficients of dispersion equations (Cauchy equation, Cornu equation, and Conrady equation). To our knowledge, this is the first time that the continuous CRID of scattering biotissue over a continuous spectral region is measured, and we hereby have proven that CCRIDM-IR is a good method for continuous CRID research of biotissue.

Rebound coefficient of collisionless gas in a rigid vessel. A model of reflection of field-reversed configuration

International Nuclear Information System (INIS)

Takaku, Yuichi; Hamada, Shigeo

1996-01-01

A system of collisionless neutral gas contained in a rigid vessel is considered as a simple model of reflection of field-reversed configuration (FRC) plasma by a magnetic mirror. The rebound coefficient of the system is calculated as a function of the incident speed of the vessel normalized by the thermal velocity of the gas before reflection. The coefficient is compared with experimental data of FIX (Osaka U.) and FRX-C/T(Los Alamos N.L.). Agreement is good for this simple model. Interesting is that the rebound coefficient takes the smallest value (∼0.365) as the incident speed tends to zero and approaches unity as it tends to infinity. This behavior is reverse to that expected for a system with collision dominated fluid instead of collisionless gas. By examining the rebound coefficient, therefore, it could be successfully inferred whether the ion mean free path in each experiment was longer or shorter than the plasma length. (author)

Reflection of ion acoustic solitons in a plasma having negative ions

International Nuclear Information System (INIS)

Chauhan, S.S.; Malik, H.K.; Dahiya, R.P.

1996-01-01

Reflection of compressive and rarefactive ion acoustic solitons propagating in an inhomogeneous plasma in the presence of negative ions is investigated. Modified Korteweg endash deVries equations for incident and reflected solitons are derived and solved. The amplitude of incident and reflected solitons increases with negative to positive ion density ratio. With increasing density ratio, reflection of rarefactive solitons is reinforced whereas that of compressive solitons weakened. The rarefactive solitons are found to undergo stronger reflection than the compressive ones. copyright 1996 American Institute of Physics

Comparison of Landsat-8 and Sentinel-2A reflectance and normalized difference vegetation index

Science.gov (United States)

Zhang, H.; Roy, D. P.; Yan, L.; Li, Z.; Huang, H.

2017-12-01

The moderate spatial resolution satellite data from the polar-orbiting Landsat-8 (launched 2013) and Sentinel-2A (launched 2015) sensors provide 10 m to 30 m multi-spectral global coverage with a better than 5-day revisit. Although a national laboratory traceable cross-calibration comparison of the Landsat-8 Operational Land Imager (OLI) and the Sentinel-2A MultiSpectral Instrument (MSI) was undertaken pre-launch, there are a number of other sensor differences, notably due to spectral, spatial and angular differences. To examine these in a comprehensive way, Landsat-8 and Sentinel-2A data for approximately 20° × 10° of southern Africa acquired in the summer (January to March) and winter (July to September) of 2016 were compared. Only Landsat-8 and Sentinel-2A observations acquired within one-day apart were considered. The sensor data were registered and then each orbit projected into 30 m fixed global Web Enabled Landsat Data (GWELD) tiles defined in the MODIS sinusoidal equal area projection. Only corresponding sensor observations of each 30 m tile pixel that were flagged as cloud and snow-free, unsaturated, and that had no significant change in their one day separation, were compared. Both the Landsat-8 and Sentinel-2A data were atmospherically corrected using the Landsat Surface Reflectance Code (LaSRC) and were also corrected to nadir BRDF adjusted reflectance (NBAR). Top of atmosphere and surface reflectance for the spectrally corresponding visible, near infrared and shortwave infrared OLI and MSI bands, and derived normalized difference vegetation index (NDVI), were compared and their differences quantified using regression analyses. The resulting statistical transformations may be used to improve the consistency between the Landsat-8 OLI and Sentinel-2A MSI data. The importance and sensitivity of the results to correct filtering, atmospheric correction and adjustment to NBAR is demonstrated.

Evanescent wave scattering at off-axis incidence on multiple cylinders located near a surface

International Nuclear Information System (INIS)

Lee, Siu-Chun

2015-01-01

The scattering characteristics of an infinite cylinder are strongly influenced by the incidence angle relative to its axis. If the incident wave propagates in the plane normal to the axis of the cylinder, the polarization of the scattered wave remains unchanged and the scattered wave propagates in the same plan as the incident wave. At off-axis incidence such that the incident direction makes an oblique angle with the cylinder axis, the scattered wave is depolarized, and its spatial distribution becomes three-dimensional. This paper presents the scattering solution for oblique incidence on multiple parallel cylinders located near a planar interface by an evanescent wave that is generated by total internal reflection of the source wave propagating in the higher refractive index substrate. Hertz potentials are utilized to formulate the interaction of inhomogeneous waves with the cylinders, scattering at the substrate interface, and near field scattering between the cylinders. Analytic formulas are derived for the electromagnetic fields and Poynting vector of scattered radiation in the near-field and their asymptotic forms in the far-field. Numerical examples are shown to illustrate scattering of evanescent wave by multiple cylinders at off-axis incidence. - Highlights: • Developed an exact solution for off-axis incidence on multiple cylinders. • Included depolarization, near-field scattering, and Fresnel effect in theory. • Derived analytic formulas for scattered radiation in the far field. • Illustrated evanescent scattering at off-axis incidence by numerical data

Modified Hitschfeld-Bordan Equations for Attenuation-Corrected Radar Rain Reflectivity: Application to Nonuniform Beamfilling at Off-Nadir Incidence

Science.gov (United States)

Meneghini, Robert; Liao, Liang

2013-01-01

As shown by Takahashi et al., multiple path attenuation estimates over the field of view of an airborne or spaceborne weather radar are feasible for off-nadir incidence angles. This follows from the fact that the surface reference technique, which provides path attenuation estimates, can be applied to each radar range gate that intersects the surface. This study builds on this result by showing that three of the modified Hitschfeld-Bordan estimates for the attenuation-corrected radar reflectivity factor can be generalized to the case where multiple path attenuation estimates are available, thereby providing a correction to the effects of nonuniform beamfilling. A simple simulation is presented showing some strengths and weaknesses of the approach.

Magnetoanisotropic spin-triplet Andreev reflection in ferromagnet-Ising superconductor junctions

Science.gov (United States)

Lv, Peng; Zhou, Yan-Feng; Yang, Ning-Xuan; Sun, Qing-Feng

2018-04-01

We theoretically study the electronic transport through a ferromagnet-Ising superconductor junction. A tight-binding Hamiltonian describing the Ising superconductor is presented. Then by combining the nonequilibrium Green's function method, the expressions of Andreev reflection coefficient and conductance are obtained. A strong magnetoanisotropic spin-triplet Andreev reflection is shown, and the magnetoanisotropic period is π instead of 2 π as in the conventional magnetoanisotropic system. We demonstrate a significant increase of the spin-triplet Andreev reflection for the single-band Ising superconductor. Furthermore, the dependence of the Andreev reflection on the incident energy and incident angle are also investigated. A complete Andreev reflection can occur when the incident energy is equal to the superconducting gap, regardless of the Fermi energy (spin polarization) of the ferromagnet. For the suitable oblique incidence, the spin-triplet Andreev reflection can be strongly enhanced. In addition, the conductance spectroscopies of both zero bias and finite bias are studied, and the influence of gate voltage, exchange energy, and spin-orbit coupling on the conductance spectroscopy are discussed in detail. The conductance exhibits a strong magnetoanisotropy with period π as the Andreev reflection coefficient. When the magnetization direction is parallel to the junction plane, a large conductance peak always emerges at the superconducting gap. This work offers a comprehensive and systematic study of the spin-triplet Andreev reflection and has an underlying application of π -periodic spin valve in spintronics.

Energy loss from internal reflection off metal layers on glass

Science.gov (United States)

McDowell, M. W.; Bezuidenhout, D. F.; Klee, H. W.; Theron, E.

1983-12-01

The reflection characteristics of metal layers are considered for the situation where the electromagnetic radiation is incident from the glass side. Theoretical and measured reflectance values are presented which indicate that for some metals the reflection has a strong dependence on the refractive index of the incident medium. Some examples are given of recent cases where the above results were an important consideration in the choice of the metallic reflecting material. These results indicate that aluminium should not be automatically considered the best choice for the visible region nor gold for the infra-red.

Neutron transmission and reflection at a copper single crystal

Energy Technology Data Exchange (ETDEWEB)

Adib, M.; Maayouf, R.M.A.; Abdel-Kawy, A.; Fayek, M.; Habib, N. (Atomic Energy Establishment, Cairo (Egypt). Reactor and Neutron Physics Dept.); Wahba, M. (Ain Shams Univ., Cairo (Egypt). Dept. of Engineering Physics and Mathematics)

1991-06-01

Neutron transmission and reflection at a copper single crystal cut along the (111) plane were studied with the fixed-scattering-angle spectrometer installed at the ET-RR-1 reactor. The transmission was measured for neutron wavelengths between 0.15 and 0.46 nm and various orientations of the (111) plane with respect to the incident beam. When used as a neutron band pass filter, the crystal is optimally oriented when the neutron beam is incident parallel to the (111) direction. The reflectivity was measured for the (111) plane at 45deg with respect to the incident beam. The results were found to be in reasonable agreement with a value predicted for the reflected intensity at an imperfect crystal with finite absorption. (orig.).

Neutron transmission and reflection at a copper single crystal

International Nuclear Information System (INIS)

Adib, M.; Maayouf, R.M.A.; Abdel-Kawy, A.; Fayek, M.; Habib, N.; Wahba, M.

1991-01-01

Neutron transmission and reflection at a copper single crystal cut along the (111) plane were studied with the fixed-scattering-angle spectrometer installed at the ET-RR-1 reactor. The transmission was measured for neutron wavelengths between 0.15 and 0.46 nm and various orientations of the (111) plane with respect to the incident beam. When used as a neutron band pass filter, the crystal is optimally oriented when the neutron beam is incident parallel to the [111] direction. The reflectivity was measured for the (111) plane at 45deg with respect to the incident beam. The results were found to be in reasonable agreement with a value predicted for the reflected intensity at an imperfect crystal with finite absorption. (orig.) [de

Evaluation of moving-coil loudspeaker and passive radiator parameters using normal-incidence sound transmission measurements: theoretical developments.

Science.gov (United States)

Leishman, Timothy W; Anderson, Brian E

2013-07-01

The parameters of moving-coil loudspeaker drivers are typically determined using direct electrical excitation and measurement. However, as electro-mechano-acoustical devices, their parameters should also follow from suitable mechanical or acoustical evaluations. This paper presents the theory of an acoustical method of excitation and measurement using normal-incidence sound transmission through a baffled driver as a plane-wave tube partition. Analogous circuits enable key parameters to be extracted from measurement results in terms of open and closed-circuit driver conditions. Associated tools are presented that facilitate adjacent field decompositions and derivations of sound transmission coefficients (in terms of driver parameters) directly from the circuits. The paper also clarifies the impact of nonanechoic receiving tube terminations and the specific benefits of downstream field decompositions.

Superradiance or total reflection?

CERN Document Server

László, András

2014-01-01

Numerical evolution of massless scalar fields on Kerr background is studied. The initial data specifications are chosen to have compact support separated from the ergoregion and to yield nearly monochromatic incident wave packets. The initial data is also tuned to maximize the effect of superradiance. Evidences are shown indicating that instead of the anticipated energy extraction from black hole the incident radiation fail to reach the ergoregion rather it suffers a nearly perfect reflection.

Quantum transport in graphene normal-metal superconductor- normal-metal structures

Directory of Open Access Journals (Sweden)

H. Mohammadpour

2008-06-01

Full Text Available  We study the transport of electrons in a graphene NSN structure in which two normal regions are connected by a superconducting strip of thickness d. Within Dirac-Bogoliubov-de Gennes equations we describe the transmission through the contact in terms of different scattering processes consisting of quasiparticle cotunneling, local and crossed Andreev reflections. Compared to a fully normal structure we show that the angular dependence of the transmission probability is significantly modified by the presence of superconducting correlations. This modifation can be explained in terms of the interplay between Andreev reflection and Klein tunneling of chiral quasiparticles. We further analyze the energy dependence of the resulting differential conductance of the structure. The subgap differential conductance shows features of Andreev reflection and cotunelling processes, which tends to the values of an NS structure for large ds. Above the gap, the differential conductance shows an oscillatory behavior with energy even at very large ds.

X-ray grazing incidence diffraction from multilayers

Energy Technology Data Exchange (ETDEWEB)

Tixier, S.; Boeni, P.; Swygenhoven, H. van; Horisberger, M. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1997-09-01

Grazing incidence scattering geometries using synchrotron radiation have been applied in order to characterise the roughness profiles and the structural coherence of multilayers. The lateral correlation length of the roughness profiles was evaluated using diffuse reflectivity in the `out of plane` geometry. This type of measurement is the only diffuse reflectivity technique allowing large lateral momentum transfer. It is typically suitable for correlation lengths smaller than 1000 A. The lateral structural coherence length of Ni{sub 3}Al/Ni multilayers as a function of the layer thickness was obtained by grazing incidence diffraction (GID). 3 figs., 1 ref.

The change in color matches with retinal angle of incidence of the colorimeter beams.

Science.gov (United States)

Alpern, M; Kitahara, H; Fielder, G H

1987-01-01

Differences between W.D.W. chromaticities of monochromatic lights obtained with all colorimeter beams incident on the retina "off-axis" and those found for lights striking the retina normally have been studied throughout the visible spectrum on 4 normal trichromats. The results are inconsistent with: (i) the assumption in Weale's theories of the Stiles-Crawford hue shift that the sets of absorption spectra of the visual pigments catching normally and obliquely incident photons are identical, and (ii) "self-screening" explanations for the change in color with angle of incidence on the retina. The color matching functions of a protanomalous trichromat are inconsistent with the hypothesis that the absorption spectra of the visual pigments catching normally incident photons in his retina are those catching obliquely incident photons in the normal retina.

Bistable Reflective Etalon (BRET)

National Research Council Canada - National Science Library

Shellenbarger, Zane

2003-01-01

This project designed, fabricated, and characterized normal-incidence etalon structures at 1550 nm wavelength operation for application, as bistable elements, to photonic analog-to-digital conversion...

Timing the total reflection of light

International Nuclear Information System (INIS)

Chauvat, Dominique; Bonnet, Christophe; Dunseath, Kevin; Emile, Olivier; Le Floch, Albert

2005-01-01

We have identified for the first time the absolute delay at total reflection, envisioned by Newton. We show that there are in fact two divergent Wigner delays, depending on the polarisation of the incident light. These measurements give a new insight on the passage from total reflection to refraction

Normal Incidence of Sound Transmission Loss of a Double-Leaf Partition Inserted with a Microperforated Panel

Directory of Open Access Journals (Sweden)

A. Putra

2013-01-01

Full Text Available A double-leaf partition in engineering structures has been widely applied for its advantages, that is, in terms of its mechanical strength as well as its lightweight property. In noise control, the double-leaf also serves as an effective noise barrier. Unfortunately at low frequency, the sound transmission loss reduces significantly due to the coupling between the panels and the air between them. This paper studies the effect of a microperforated panel (MPP inserted inside a double-leaf partition on the sound transmission loss performance of the system. The MPP insertion is proposed to provide a hygienic double-leaf noise insulator replacing the classical abrasive porous materials between the panels. It is found that the transmission loss improves at the troublesome mass-air-mass resonant frequency if the MPP is located closer to the solid panel. The mathematical model is derived for normal incidence of acoustic loading.

Measures of Disease Frequency: Prevalence and Incidence

NARCIS (Netherlands)

Noordzij, Marlies; Dekker, Friedo W.; Zoccali, Carmine; Jager, Kitty J.

2010-01-01

To describe how often a disease or another health event occurs in a population, different measures of disease frequency can be used. The prevalence reflects the number of existing cases of a disease. In contrast to the prevalence, the incidence reflects the number of new cases of disease and can be

Earth Reflected Solar Radiation Incident upon an Arbitrarily Oriented Spinning Flat Plate

Science.gov (United States)

Cunningham, Fred G.

1963-01-01

A general derivation is given for the earth reflected solar radiation input to a flat plate--a solar cell paddle, for example--which is spinning about an axis coincident with the axis of symmetry of the satellite to which it is affixed. The resulting equations are written for the general case so that arbitrary orientations of the spin axis with respect to the earth-satellite line and arbitrary orientations of the normal to the plate with respect to the spin axis can be treated. No attempt is made to perform the resulting integrations because of the complexity of the equations; nor is there any attempt to delineate the integration limits for the general case. However, the equations governing these limits are given. The appendixes contain: the results, in graphical form, of two representative examples; the general computer program for the calculation is given in Fortran notation; and the results of a calculation of the distribution of albedo energy on the proposed Echo II satellite. The value of the mean solar constant used is 1.395 times 10 (sup 4) ergs per centimeters-squared per second; the mean albedo of the earth is assumed to be 0.34; and the earth is assumed to be a diffuse reflector.

Detection limit calculations for different total reflection techniques

International Nuclear Information System (INIS)

Sanchez, H.J.

2000-01-01

In this work, theoretical calculations of detection limits for different total-reflection techniques are presented.. Calculations include grazing incidence (TXRF) and gracing exit (GEXRF) conditions. These calculations are compared with detection limits obtained for conventional x-ray fluorescence (XRF). In order to compute detection limits the Shiraiwa and Fujino's model to calculate x-ray fluorescence intensities was used. This model made certain assumptions and approximations to achieve the calculations, specially in the case of the geometrical conditions of the sample, and the incident and takeoff beams. Nevertheless the calculated data of detection limits for conventional XRF and total-reflection XRF show a good agreement with previous results. The model proposed here allows to analyze the different sources of background and the influence of the excitation geometry, which contribute to the understanding of the physical processes involved in the XRF analysis by total reflection. Finally, a comparison between detection limits in total-reflection analysis at grazing incidence and at grazing exit is carried out. Here a good agreement with the theoretical predictions of the reversibility principle is found, showing that detection limits are similar for both techniques. (author)

Obliquely Incident Solitary Wave onto a Vertical Wall

Science.gov (United States)

Yeh, Harry

2012-10-01

When a solitary wave impinges obliquely onto a reflective vertical wall, it can take the formation of a Mach reflection (a geometrically similar reflection from acoustics). The mathematical theory predicts that the wave at the reflection can amplify not twice, but as high as four times the incident wave amplitude. Nevertheless, this theoretical four-fold amplification has not been verified by numerical or laboratory experiments. We discuss the discrepancies between the theory and the experiments; then, improve the theory with higher-order corrections. The modified theory results in substantial improvement and is now in good agreement with the numerical as well as our laboratory results. Our laboratory experiments indicate that the wave amplitude along the reflective wall can reach 0.91 times the quiescent water depth, which is higher than the maximum of a freely propagating solitary wave. Hence, this maximum runup 0.91 h would be possible even if the amplitude of the incident solitary wave were as small as 0.24 h. This wave behavior could provide an explanation for local variability of tsunami runup as well as for sneaker waves.

The quiet Sun extreme ultraviolet spectrum observed in normal incidence by the SOHO Coronal Diagnostic Spectrometer

CERN Document Server

Brooks, D H; Fludra, A; Harrison, R A; Innes, D E; Landi, E; Landini, M; Lang, J; Lanzafame, A C; Loch, S D; McWhirter, R W P; Summers, H P; Thompson, W T

1999-01-01

The extreme ultraviolet quiet Sun spectrum, observed at normal incidence by the Coronal Diagnostic Spectrometer on the SOHO spacecraft, is presented. The spectrum covers the wavelength ranges 308-381 AA and 513-633 AA and is based $9 on data recorded at various positions on the solar disk between October 1996 and February 1997. Datasets at twelve of these `positions' were judged to be free from active regions and data faults and selected for detailed study. A $9 constrained maximum likelihood spectral line fitting code was used to analyse the spectral features. In all over 200 spectrum lines have been measured and about 50 186584dentified. The line identification process consisted of a $9 number of steps. Firstly assignment of well known lines was made and used to obtain the primary wavelength calibration. Variations of wavelengths with position were used to assess the precision of calibration achievable. Then, an $9 analysis method first used in studies with the CHASE experiment, was applied to the new obser...

Reflected Sunlight Reduction and Characterization for a Deep-Space Optical Receiver Antenna (DSORA)

Science.gov (United States)

Clymer, B. D.

1990-01-01

A baffle system for the elimination of first-order specular and diffuse reflection of sunlight from the sunshade of a deep-space optical receiver telescope is presented. This baffle system consists of rings of 0.5cm blades spaced 2.5 cm apart on the walls of GO hexagonal sunshade tubes that combine to form the telescope sunshade. The shadow cast by the blades, walls, and rims of the tubes prevent all first-order reflections of direct sunlight from reaching the primary mirror of the telescope. A reflection model of the sunshade without baffles is also presented for comparison. Since manufacturers of absorbing surfaces do not measure data near grazing incidence, the reflection properties at anticipated angles of incidence must be characterized. A description of reflection from matte surfaces in term of bidirectional reflection distribution function (BRDF) is presented along with a discussion of measuring BRDF near grazing incidence.

Determination of electromagnetic absorption parameters by reflection measurements

International Nuclear Information System (INIS)

Vittitoe, C.N.

1975-09-01

The method described is for determining the electromagnetic absorption parameters of a material by measuring the optical reflection from a thick sample. With linearly polarized incident light (both perpendicular to and parallel to the plane of incidence), the ratio of the reflected intensities at three or more angles of incidence offers promise for determining the complex index of refraction of a material for a broad range of parameter values. The method may be applicable to molten materials, such as UO 2 , where high temperatures cause corrosion and containment difficulties. A method is given for extending the data to neighboring frequencies. Use of the method was successful for all portions of the complex index of refraction plane except for small values of the extinction coefficient

Monte Carlo simulation of spectral reflectance and BRDF of the bubble layer in the upper ocean.

Science.gov (United States)

Ma, Lanxin; Wang, Fuqiang; Wang, Chengan; Wang, Chengchao; Tan, Jianyu

2015-09-21

The presence of bubbles can significantly change the radiative properties of seawater and these changes will affect remote sensing and underwater target detection. In this work, the spectral reflectance and bidirectional reflectance characteristics of the bubble layer in the upper ocean are investigated using the Monte Carlo method. The Hall-Novarini (HN) bubble population model, which considers the effect of wind speed and depth on the bubble size distribution, is used. The scattering coefficients and the scattering phase functions of bubbles in seawater are calculated using Mie theory, and the inherent optical properties of seawater for wavelengths between 300 nm and 800 nm are related to chlorophyll concentration (Chl). The effects of bubble coating, Chl, and bubble number density on the spectral reflectance of the bubble layer are studied. The bidirectional reflectance distribution function (BRDF) of the bubble layer for both normal and oblique incidence is also investigated. The results show that bubble populations in clear waters under high wind speed conditions significantly influence the reflection characteristics of the bubble layer. Furthermore, the contribution of bubble populations to the reflection characteristics is mainly due to the strong backscattering of bubbles that are coated with an organic film.

The trapping of potassium atoms by a polycrystalline tungsten surface as a function of energy and angle of incidence. ch. 1

International Nuclear Information System (INIS)

Hurkmans, A.; Overbosch, E.G.; Olander, D.R.; Los, J.

1976-01-01

The trapping probability of potassium atoms on a polycrystalline tungsten surface has been measured as a function of the angle of incidence and as a function of the energy of the incoming atoms. Below an energy of 1 eV the trapping was complete; above 20 eV only reflection occurred. The trapping probability increased with increasing angle of incidence. The measurements are compared with a simple model of the fraction of atoms initially trapped. The model, a one-dimensional cube model including a Boltzmann distribution of the velocities of oscillating surface atoms, partially explains the data. The trapping probability as a function of incoming energy is well described for normal incidence, justifying the inclusion of thermal motion of the surface atoms in the model. The angular dependence can be explained in a qualitative way, although there is a substantial discrepancy for large angles of incidence, showing the presence of surface structure. (Auth.)

Computer Program for Calculation of Complex Chemical Equilibrium Compositions, Rocket Performance, Incident and Reflected Shocks, and Chapman-Jouguet Detonations. Interim Revision, March 1976

Science.gov (United States)

Gordon, S.; Mcbride, B. J.

1976-01-01

A detailed description of the equations and computer program for computations involving chemical equilibria in complex systems is given. A free-energy minimization technique is used. The program permits calculations such as (1) chemical equilibrium for assigned thermodynamic states (T,P), (H,P), (S,P), (T,V), (U,V), or (S,V), (2) theoretical rocket performance for both equilibrium and frozen compositions during expansion, (3) incident and reflected shock properties, and (4) Chapman-Jouguet detonation properties. The program considers condensed species as well as gaseous species.

Alfven Wave Reflection Model of Field-Aligned Currents at Mercury

Science.gov (United States)

Lyatsky, Wladislaw; Khazanov, George V.; Slavin, James

2010-01-01

An Alfven Wave Reflection (AWR) model is proposed that provides closure for strong field-aligned currents (FACs) driven by the magnetopause reconnection in the magnetospheres of planets having no significant ionospheric and surface electrical conductance. The model is based on properties of the Alfven waves, generated at high altitudes and reflected from the low-conductivity surface of the planet. When magnetospheric convection is very slow, the incident and reflected Alfven waves propagate along approximately the same path. In this case, the net field-aligned currents will be small. However, as the convection speed increases. the reflected wave is displaced relatively to the incident wave so that the incident and reflected waves no longer compensate each other. In this case, the net field-aligned current may be large despite the lack of significant ionospheric and surface conductivity. Our estimate shows that for typical solar wind conditions at Mercury, the magnitude of Region 1-type FACs in Mercury's magnetosphere may reach hundreds of kilo-Amperes. This AWR model of field-aligned currents may provide a solution to the long-standing problem of the closure of FACs in the Mercury's magnetosphere. c2009 Elsevier Inc. All rights reserved.

Comparison of incidences of normal tissue complications with tumor response in a phase III trial comparing heat plus radiation to radiation alone

International Nuclear Information System (INIS)

Dewhirst, M.W.; Sim, D.A.; Grochowski, K.J.

1984-01-01

The success of hyperthermia (/sup Δ/) as an adjuvant to radiation (XRT) will depend on whether the increase in tumor control is greater than that for normal tissue reactions. One hundred and thirty dogs and cats were stratified by histology and randomized to receive XRT (460 rads per fraction, two fractions per week, for eight fractions) or /sup Δ/ + XRT (30 min. at 44 +-2 0 C; one fraction per week, four fractions; immediately prior to XRT). Heat induced changes in tumor and normal tissue responses were made by comparing ratios of incidence for /sup Δ/ + XRT and XRT alone (TRR; Thermal Relative Risk). Change in tumor response duration was calculated from statistical analysis of response duration curves (RRR; Relative Relapse Rate). Heat increased early normal tissue reactions (moist desquamation and mucositis by a factor of 1.08. Tumor complete response, by comparison, was significantly improved (TRR = 2.12, p < .001). Late skin fibrosis was also increased (TRR = 1.51), but the prolongation in tumor response was greater (RRR 1.85). The degree of thermal enhancement for all tissues was dependent on the minimum temperature achieved on the first treatment, but the values for tumor were consistently greater than those achieved for normal tissues

Pelvic incidence variation among individuals: functional influence versus genetic determinism.

Science.gov (United States)

Chen, Hong-Fang; Zhao, Chang-Qing

2018-03-20

Pelvic incidence has become one of the most important sagittal parameters in spinal surgery. Despite its great importance, pelvic incidence can vary from 33° to 85° in the normal population. The reasons for this great variability in pelvic incidence remain unexplored. The objective of this article is to present some possible interpretations for the great variability in pelvic incidence under both normal and pathological conditions and to further understand the determinants of pelvic incidence from the perspective of the functional requirements for bipedalism and genetic backgrounds via a literature review. We postulate that both pelvic incidence and pelvic morphology may be genetically predetermined, and a great variability in pelvic incidence may already exist even before birth. This great variability may also serve as a further reminder that the sagittal profile, bipedal locomotion mode, and genetic background of every individual are unique and specific, and clinicians should avoid making universally applying broad generalizations of pelvic incidence. Although PI is an important parameter and there are many theories behind its variability, we still do not have clear mechanistic answers.

Frustrated Total Internal Reflection: A Simple Application and Demonstration.

Science.gov (United States)

Zanella, F. P.; Magalhaes, D. V.; Oliveira, M. M.; Bianchi, R. F.; Misoguti, L.; Mendonca, C. R.

2003-01-01

Describes the total internal reflection process that occurs when the internal angle of incidence is equal to or greater than the critical angle. Presents a demonstration of the effect of frustrated total internal reflection (FTIR). (YDS)

Anomalous normal mode oscillations in semiconductor microcavities

Energy Technology Data Exchange (ETDEWEB)

Wang, H. [Univ. of Oregon, Eugene, OR (United States). Dept. of Physics; Hou, H.Q.; Hammons, B.E. [Sandia National Labs., Albuquerque, NM (United States)

1997-04-01

Semiconductor microcavities as a composite exciton-cavity system can be characterized by two normal modes. Under an impulsive excitation by a short laser pulse, optical polarizations associated with the two normal modes have a {pi} phase difference. The total induced optical polarization is then expected to exhibit a sin{sup 2}({Omega}t)-like oscillation where 2{Omega} is the normal mode splitting, reflecting a coherent energy exchange between the exciton and cavity. In this paper the authors present experimental studies of normal mode oscillations using three-pulse transient four wave mixing (FWM). The result reveals surprisingly that when the cavity is tuned far below the exciton resonance, normal mode oscillation in the polarization is cos{sup 2}({Omega}t)-like, in contrast to what is expected form the simple normal mode model. This anomalous normal mode oscillation reflects the important role of virtual excitation of electronic states in semiconductor microcavities.

Optical Analysis of Grazing Incidence Ring Resonators for Free-Electron Lasers

Science.gov (United States)

Gabardi, David Richard

1990-08-01

The design of resonators for free-electron lasers (FELs) which are to operate in the soft x-ray/vacuum ultraviolet (XUV) region of the spectrum is complicated by the fact that, in this wavelength regime, normal incidence mirrors, which would otherwise be used for the construction of the resonators, generally have insufficient reflectivities for this purpose. However, the use of grazing incidence mirrors in XUV resonators offers the possibility of (1) providing sufficient reflectivity, (2) a lessening of the mirrors' thermal loads due to the projection of the laser beam onto an oblique surface, and (3) the preservation of the FEL's tunability. In this work, the behavior of resonators employing grazing incidence mirrors in ring type configurations is explored. In particular, two designs, each utilizing four off-axis conic mirrors and a number of flats, are examined. In order to specify the location, orientation, and surface parameters for the mirrors in these resonators, a design algorithm has been developed based upon the properties of Gaussian beam propagation. Two computer simulation methods are used to perform a vacuum stability analysis of the two resonator designs. The first method uses paraxial ray trace techniques with the resonators' thin lens analogues while the second uses the diffraction-based computer simulation code GLAD (General Laser Analysis and Design). The effects of mirror tilts and deviations in the mirror surface parameters are investigated for a number of resonators designed to propagate laser beams of various Rayleigh ranges. It will be shown that resonator stability decreases as the laser wavelength for which the resonator was designed is made smaller. In addition, resonator stability will also be seen to decrease as the amount of magnification the laser beam receives as it travels around the resonator is increased.

Combined evaluation of grazing incidence X-ray fluorescence and X-ray reflectivity data for improved profiling of ultra-shallow depth distributions

Energy Technology Data Exchange (ETDEWEB)

Ingerle, D., E-mail: dingerle@ati.ac.at [Atominstitut, Vienna University of Technology, Stadionallee 2, A-1020 Vienna (Austria); Meirer, F. [Inorganic Chemistry and Catalysis, Debye Institute for Nanomaterials Science, Utrecht University, Universiteitsweg 99, 3584 CG Utrecht (Netherlands); Pepponi, G.; Demenev, E.; Giubertoni, D. [MiNALab, CMM-irst, Fondazione Bruno Kessler, Via Sommarive 18, I-38050 Povo (Italy); Wobrauschek, P.; Streli, C. [Atominstitut, Vienna University of Technology, Stadionallee 2, A-1020 Vienna (Austria)

2014-09-01

The continuous downscaling of the process size for semiconductor devices pushes the junction depths and consequentially the implantation depths to the top few nanometers of the Si substrate. This motivates the need for sensitive methods capable of analyzing dopant distribution, total dose and possible impurities. X-ray techniques utilizing the external reflection of X-rays are very surface sensitive, hence providing a non-destructive tool for process analysis and control. X-ray reflectometry (XRR) is an established technique for the characterization of single- and multi-layered thin film structures with layer thicknesses in the nanometer range. XRR spectra are acquired by varying the incident angle in the grazing incidence regime while measuring the specular reflected X-ray beam. The shape of the resulting angle-dependent curve is correlated to changes of the electron density in the sample, but does not provide direct information on the presence or distribution of chemical elements in the sample. Grazing Incidence XRF (GIXRF) measures the X-ray fluorescence induced by an X-ray beam incident under grazing angles. The resulting angle dependent intensity curves are correlated to the depth distribution and mass density of the elements in the sample. GIXRF provides information on contaminations, total implanted dose and to some extent on the depth of the dopant distribution, but is ambiguous with regard to the exact distribution function. Both techniques use similar measurement procedures and data evaluation strategies, i.e. optimization of a sample model by fitting measured and calculated angle curves. Moreover, the applied sample models can be derived from the same physical properties, like atomic scattering/form factors and elemental concentrations; a simultaneous analysis is therefore a straightforward approach. This combined analysis in turn reduces the uncertainties of the individual techniques, allowing a determination of dose and depth profile of the implanted

Transport through hybrid superconducting/normal nanostructures

Energy Technology Data Exchange (ETDEWEB)

Futterer, David

2013-01-29

study transport through proximized interacting quantum dots. Not only does a finite superconducting gap give rise to renormalization effects but also the coupling to the normal lead can evoke renormalizations. To explore these we calculate the correction terms arising from the coupling to the normal lead and identify renormalizations of the 0-{pi} transitions of the Josephson current, the extrema of the Andreev current, and the average dot charge. In the previous works the occurring normal conducting leads are assumed to be metallic so that the shape of the band structure can be neglected. If the normal conducting region is a semiconductor, the shape of the band structure plays an important role. In our last calculation we consider a p-type semiconductor-superconductor interface and study oblique injections of light holes and heavy holes. Solving the Bogolyubov-de Gennes equations for a 6 x 6 Kane model we find that light holes and heavy holes can be Andreev reflected and in this process converted into each other. Moreover, in perpendicular incidence heavy holes cannot be Andreev reflected. Two types of critical angles occur. First, a critical angle above which conversion-less Andreev reflection is no longer possible and, second, a critical angle above which heavy holes cannot be converted into light holes anymore.

Transport through hybrid superconducting/normal nanostructures

International Nuclear Information System (INIS)

Futterer, David

2013-01-01

study transport through proximized interacting quantum dots. Not only does a finite superconducting gap give rise to renormalization effects but also the coupling to the normal lead can evoke renormalizations. To explore these we calculate the correction terms arising from the coupling to the normal lead and identify renormalizations of the 0-π transitions of the Josephson current, the extrema of the Andreev current, and the average dot charge. In the previous works the occurring normal conducting leads are assumed to be metallic so that the shape of the band structure can be neglected. If the normal conducting region is a semiconductor, the shape of the band structure plays an important role. In our last calculation we consider a p-type semiconductor-superconductor interface and study oblique injections of light holes and heavy holes. Solving the Bogolyubov-de Gennes equations for a 6 x 6 Kane model we find that light holes and heavy holes can be Andreev reflected and in this process converted into each other. Moreover, in perpendicular incidence heavy holes cannot be Andreev reflected. Two types of critical angles occur. First, a critical angle above which conversion-less Andreev reflection is no longer possible and, second, a critical angle above which heavy holes cannot be converted into light holes anymore.

SOUND TRANSMISSION LOSS OF A DOUBLE-LEAF SOLID-MICROPERFORATED PARTITION UNDER NORMAL INCIDENCE OF ACOUSTIC LOADING

Directory of Open Access Journals (Sweden)

Ahmad Yusuf Ismail

2011-12-01

Full Text Available 0 0 1 332 1894 International Islamic University 15 4 2222 14.0 Normal 0 false false false EN-US JA X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Times New Roman";} The micro-perforated panel (MPP is recently well-known as an alternative ‘green‘ sound absorber replacing the conventional porous materials. Constructed from a solid panel which provides a non-abrassive structure and also an optically attractive surface, there gives a feasibility to implement such a panel inside a vehicle cabin. This paper is the preliminary study to investigate the sound transmission loss (TL of a solid panel coupled with a micro-perforated panel to form a doube-leaf partition which is already known as a lightweigth stucture for noise insulation in vehicles and buildings. The mathematical model for the TL subjected to normal incidence of acoustic excitation is derived. The results show that its performance substantially improves at the troublesome frequency of mass-air-mass resonance which occurs in the conventional double-leaf solid partition. This is important particularly for the noise source predominant at low frequencies. This can also be controlled by tuning the hole size and number as well as the air gap between the panels.  ABSTRAK: Panel bertebuk mikro (micro-perforated panel (MPP kebelakangan ini dikenali sebagai alternatif penyerap bunyi yang mesra alam menggantikan bahan berliang lazim. Dibina daripada satu panel padu yang memberikan satu struktur tak lelas dan juga satu permukaan yang menarik, ia memberikan kemungkinan penggunaan panel tersebut di dalam kabin kenderaan. Tesis ini merupakan kajian permulaan dalam mengkaji hilang pancaran bunyi

Monte Carlo calculations of ligth-ion sputtering as a function of the incident angle

International Nuclear Information System (INIS)

Haggmark, L.G.; Biersack, J.P.

1980-01-01

The sputtering of metal surfaces by light ions has been studied as a function of the incident angle using an extension of the TRIM Monte Carlo computer program. Sputtering yields were calculated at both normal and oblique angles of incidence for H, D, T, and 4 He impinging on Ni, Mo, and Au targets with energies <= 10 keV. Direct comparisons are made with the most recent experimental and theoretical results. There is generally good agreement with the experimental data although our calculated maximum in the yield usually occurs at a smaller incident angle, measured from the surface normal. The enhancement of the yield at large incident angles over that at normal incidence is observed to be a complex function of the incident ion's energy and mass and the target's atomic weight and surface binding energy. (orig.)

Quantum reflection in the linearly downward potential

Science.gov (United States)

Chamnan, N.; Krunavakarn, B.

2017-09-01

In this work, the motion of a particle in one dimension under the influence of the linearly downward potential well is studied within the context of the non-relativistic quantum mechanics. The attention is paid on the paradoxical phenomenon of the reflection of a particle that is in contrast between classical and quantum physics. Classically, the reflection effect occurs only at a potential barrier. To demonstrate such counter-intuitive phenomenon, the Schrödinger equation is solved to obtain the reflection coefficient in the scattering state by considering an incident particle that is represented by a monochromatic plane wave having an energy E > 0, propagates freely from left to right, pass through the potential well. The continuity conditions at boundaries give the desired result that is expressed in terms of the Airy functions which depends on the incident energy E, the strength jV 0 j and the range L of the well. The value of the reflection coefficient R lies in the interval 0 < R < 1, and its behavior is the decreasing function with respect to the range L.

Elemental concentration in normal skin and fibroepithelial polip lesions by synchrotron radiation total reflection X-ray fluorescence technique

International Nuclear Information System (INIS)

Soares, Julio C.A.C.R.; Canellas, Catarine G.L.; Lopes, Ricardo T.; Anjos, Marcelino J.

2011-01-01

In this work, the concentrations of trace elements were measured in acrochordon, a skin lesion also known as skin tag or fibroepithelial polyp, as well as in normal skin from the same patient. The samples were analysed by Synchrotron Radiation Total Reflection X- ray Fluorescence (SRTXRF) in the Synchrotron Light National Laboratory (LNLS) in Campinas/Sao Paulo-Brazil. The collection of lesion and healthy skin samples, including papillary dermis and epidermis, has involved 17 patients. It was evaluated the presence of P, S, Cl, K, Ca, Cr, Mn, Fe, Cu, Zn, Br and Rb in the paired samples, which were compared, and significant differences were found in some of them. (author)

Theoretical analysis of open aperture reflection Z-scan on materials with high-order optical nonlinearities

International Nuclear Information System (INIS)

Petris, Adrian I.; Vlad, Valentin I.

2010-03-01

We present a theoretical analysis of open aperture reflection Z-scan in nonlinear media with third-, fifth-, and higher-order nonlinearities. A general analytical expression for the normalized reflectance when third-, fifth- and higher-order optical nonlinearities are excited is derived and its consequences on RZ-scan in media with high-order nonlinearities are discussed. We show that by performing RZ-scan experiments at different incident intensities it is possible to put in evidence the excitation of different order nonlinearities in the medium. Their contributions to the overall nonlinear response can be discriminated by using formulas derived by us. A RZ-scan numerical simulation using these formulas and data taken from literature, measured by another method for the third-, fifth-, and seventh-order nonlinear refractive indices of As 2 S 3 chalcogenide glass, is performed. (author)

The management of radiation treatment error through incident learning

International Nuclear Information System (INIS)

Clark, Brenda G.; Brown, Robert J.; Ploquin, Jodi L.; Kind, Anneke L.; Grimard, Laval

2010-01-01

Purpose: To assess efficacy of an incident learning system in the management of error in radiation treatment. Materials and methods: We report an incident learning system implementation customized for radiation therapy where any 'unwanted or unexpected change from normal system behaviour that causes or has the potential to cause an adverse effect to persons or equipment' is reported, investigated and learned from. This system thus captures near-miss (potential) and actual events. Incidents are categorized according to severity, type and origin. Results: Our analysis spans a period of 3 years with an average accrual of 11.6 incidents per week. We found a significant reduction in actual incidents of 28% and 47% in the second and third year when compared to the first year (p < 0.001), which we attribute to the many interventions prompted by the analysis of incidents reported. We also saw a similar significant reduction in incidents generated at the treatment unit correlating with the introduction of direct treatment parameter transfer and electronic imaging (p < 0.001). Conclusions: Implementation of an incident learning system has helped us to establish a just environment where all staff members report deviations from normal system behaviour and thus generate evidence to initiate safety improvements.

Catheter based mid-infrared reflectance and reflectance generated absorption spectroscopy

Science.gov (United States)

Holman, Hoi-Ying N

2013-10-29

A method of characterizing conditions in a tissue, by (a) providing a catheter that has a light source that emits light in selected wavenumbers within the range of mid-IR spectrum; (b) directing the light from the catheter to an area of tissue at a location inside a blood vessel of a subject; (c) collecting light reflected from the location and generating a reflectance spectra; and (d) comparing the reflectance spectra to a reference spectra of normal tissue, whereby a location having an increased number of absorbance peaks at said selected wavenumbers indicates a tissue inside the blood vessel containing a physiological marker for atherosclerosis.

Reflection and refraction of light from a moving block of glass

International Nuclear Information System (INIS)

Lerche, I.

1975-01-01

For a block of glass moving with speed βc we present calculations which give the changes in the laws of reflection and refraction of light from the laws which hold when β = 0. In particular we show (i) that changes in the critical internal reflection condition, although formally of order β 2 , are obtainable by measuring the refraction angle to O(β); (ii) the reflection coefficient depends not only on the polarization plane of the incident light but also on whether the plane of incidence does, or does not, include the direction of motion of the glass block. For instance, for light incident in a plane perpendicular to the direction of motion there is no Brewster angle for either plane of polarization, while for light incident in a plane containing the direction of motion at least one (and sometimes both) plane of polarization possess a Brewster angle. We have done these calculations in order to demonstrate that the shearing of one medium relative to another can have profound effects on the reflection and refraction of light. A major point here is that even when it might appear a priori that O(β 2 ) phenomena are unobservable in the laboratory, the present calculations show that this is not always so

Reflection from a flat dielectric film with negative refractive index

OpenAIRE

Hillion, Pierre

2007-01-01

We analyse the reflection of a TM electromagnetic field first on a flat dielectric film and second on a Veselago film with negative refractive index, both films being deposited on a metallic substrat acting as a mirror. An incident harmonic plane wave generates inside a conventional dielectric film a refracted propagating wave and an evanescent wave that does not contribute to reflection on the metallic substrat so that part of the information conveyed by the incident field is lost. At the op...

Investigation of omnidirectional reflection band in ZnTe/ZnSe distributed Bragg reflector

Energy Technology Data Exchange (ETDEWEB)

Huang, Ying-Shin [Department of Electrical Engineering, National Taiwan Ocean University, Keelung 20224, Taiwan (China); Hu, Sheng-Yao [Department of Digital Technology Design, Tungfang Design University, Kaohsiung 82941, Taiwan (China); Lee, Yueh-Chien, E-mail: jacklee@mail.tnu.edu.tw [Department of Electronic Engineering, Tungnan University, New Taipei City 22202, Taiwan (China); Chang, Chung-Cheng; Tiong, Kwong-Kau [Department of Electrical Engineering, National Taiwan Ocean University, Keelung 20224, Taiwan (China); Shen, Ji-Lin [Department of Physics, Chung Yuan Christian University, Chung-Li 32023, Taiwan (China); Chou, Wu-Ching [Department of Electrophysics, National Chiao Tung University, Hsinchu 30010, Taiwan (China)

2015-11-15

We report the characteristics of reflectance spectra of the 15- and 20-period ZnTe/ZnSe distributed Bragg reflector grown on GaAs (001) substrates by molecular beam epitaxy. The reflectance spectra measured at various incident angles and polarizations were investigated by the theoretical curves simulated using transfer matrix method. The wavelength variation of the refractive indices described by Sellmeier equation and random thickness model were also considered for the interpretation of the experimentally observed curves. An omnidirectional reflection range defined from the edge of incident-angle-dependent reflection band with TE and TM polarizations is about 15 nm, and is consistent with the observed experimental curves. The results showed that the selected ZnTe and ZnSe materials are suitable for constructing multilayer structures having omnidirectional reflection band. - Highlights: • ZnTe/ZnSe distributed Bragg reflector grown by molecular beam epitaxy. • The reflectance spectra are measured at various incidence angles and polarizations. • The theoretical curves are considered by Sellmeier and random thickness models. • An observed omnidirectional reflection range in ZnTe/ZnSe DBR is about 15 nm.

Memory Binding Test Predicts Incident Amnestic Mild Cognitive Impairment.

Science.gov (United States)

Mowrey, Wenzhu B; Lipton, Richard B; Katz, Mindy J; Ramratan, Wendy S; Loewenstein, David A; Zimmerman, Molly E; Buschke, Herman

2016-07-14

The Memory Binding Test (MBT), previously known as Memory Capacity Test, has demonstrated discriminative validity for distinguishing persons with amnestic mild cognitive impairment (aMCI) and dementia from cognitively normal elderly. We aimed to assess the predictive validity of the MBT for incident aMCI. In a longitudinal, community-based study of adults aged 70+, we administered the MBT to 246 cognitively normal elderly adults at baseline and followed them annually. Based on previous work, a subtle reduction in memory binding at baseline was defined by a Total Items in the Paired (TIP) condition score of ≤22 on the MBT. Cox proportional hazards models were used to assess the predictive validity of the MBT for incident aMCI accounting for the effects of covariates. The hazard ratio of incident aMCI was also assessed for different prediction time windows ranging from 4 to 7 years of follow-up, separately. Among 246 controls who were cognitively normal at baseline, 48 developed incident aMCI during follow-up. A baseline MBT reduction was associated with an increased risk for developing incident aMCI (hazard ratio (HR) = 2.44, 95% confidence interval: 1.30-4.56, p = 0.005). When varying the prediction window from 4-7 years, the MBT reduction remained significant for predicting incident aMCI (HR range: 2.33-3.12, p: 0.0007-0.04). Persons with poor performance on the MBT are at significantly greater risk for developing incident aMCI. High hazard ratios up to seven years of follow-up suggest that the MBT is sensitive to early disease.

Bi-directional reflectance distribution function of a tungsten block for ITER divertor

International Nuclear Information System (INIS)

Iwamae, Atsushi; Ogawa, Hiroaki; Sugie, Tatsuo; Kusama, Yoshinori

2012-02-01

In order to investigate reflection properties on plasma-facing material in ITER, the bi-directional reflectance distribution function (BRDF) of a tungsten block sample has been measured. On the machining surface of the block, one-directional machining lines are engraved. Two laser diodes λ652 nm and λ473 nm were used to simulate H α and H β emissions, respectively. The reflected light is affected by the machining surface. The reflected light traces an arc when the incident light is injected in the parallel direction to the engraved line. On the other hand the reflected light traces a line shape when the incident light is injected in the perpendicular direction to the engraved lines. Ray tracing simulation qualitatively explains the experimental results. (author)

On Optimal, Minimal BRDF Sampling for Reflectance Acquisition

DEFF Research Database (Denmark)

Nielsen, Jannik Boll; Jensen, Henrik Wann; Ramamoorthi, Ravi

2015-01-01

The bidirectional reflectance distribution function (BRDF) is critical for rendering, and accurate material representation requires data-driven reflectance models. However, isotropic BRDFs are 3D functions, and measuring the reflectance of a flat sample can require a million incident and outgoing...... direction pairs, making the use of measured BRDFs impractical. In this paper, we address the problem of reconstructing a measured BRDF from a limited number of samples. We present a novel mapping of the BRDF space, allowing for extraction of descriptive principal components from measured databases......, such as the MERL BRDF database. We optimize for the best sampling directions, and explicitly provide the optimal set of incident and outgoing directions in the Rusinkiewicz parameterization for n = {1, 2, 5, 10, 20} samples. Based on the principal components, we describe a method for accurately reconstructing BRDF...

Inverting reflections using full-waveform inversion with inaccurate starting models

KAUST Repository

AlTheyab, Abdullah; Schuster, Gerard T.

2015-01-01

We present a method for inverting seismic reflections using full-waveform inversion (FWI) with inaccurate starting models. For a layered medium, near-offset reflections (with zero angle of incidence) are unlikely to be cycle-skipped regardless

Higher Levels of Albuminuria within the Normal Range Predict Incident Hypertension

OpenAIRE

Forman, John P.; Fisher, Naomi D.L.; Schopick, Emily L.; Curhan, Gary C.

2008-01-01

Higher levels of albumin excretion within the normal range are associated with cardiovascular disease in high-risk individuals. Whether incremental increases in urinary albumin excretion, even within the normal range, are associated with the development of hypertension in low-risk individuals is unknown. This study included 1065 postmenopausal women from the first Nurses’ Health Study and 1114 premenopausal women from the second Nurses’ Health Study who had an albumin/creatinine ratio

Robust glint detection through homography normalization

DEFF Research Database (Denmark)

Hansen, Dan Witzner; Roholm, Lars; García Ferreiros, Iván

2014-01-01

A novel normalization principle for robust glint detection is presented. The method is based on geometric properties of corneal reflections and allows for simple and effective detection of glints even in the presence of several spurious and identically appearing reflections. The method is tested...

Kadar leptin saliva dan kejadian karies gigi anak obesitas (Salivary leptin levels and caries incidence in obese children

Directory of Open Access Journals (Sweden)

Elfrida Atzmaryanni

2013-09-01

Full Text Available Background: Children with obesity have a lower incidence of caries. Salivary leptin levels of obese children is higher than normal children. Leptin is protein hormone, contained in saliva. Salivary proteins maintain the balance of the ecosystem in the mouth. Purpose: The article was aimed to study the correlation of salivary leptin levels with caries incidence in obese children. Review: Mouth is reflection of the health status and so many changes occur as a weight gain. Child with obesity has a low incidence of caries than normal. This condition is associated with changes in oral cavity, especially the increase in salivary leptin. Caries is a disease of hard tissues cause by the activty of microorganisms, especially Streptococcus mutans. Salivary proteins maintain the balance of the ecosystem in the mouth. Leptin is a protein saliva, produced predominantly in adipose tissue and conduct active transport to saliva. Salivary leptin works in two ways: as an antimicrobial which prevents the attachment of bacteria on tooth surface or by inducing cytokine that affect the immune system in oral cavity. Conclusion: Salivary leptin is higher in obese children than in normal children. The low incidence of caries on obesity is associated with salivary leptin. Alteration in salivary composition and flow rate also decreased caries in obesity.Latar belakang: Anak yang mengalami obesitas memiliki insiden karies yang rendah. Kadar leptin saliva anak obesitas lebih tinggi dari anak normal. Leptin merupakan salah satu protein hormon yang terdapat di saliva. Protein saliva berfungsi untuk menjaga keseimbangan ekosistem di mulut. Tujuan: Artikel ini bertujuan mempelajari hubungan antara kadar leptin di dalam saliva dengan kejadian karies anak obesitas. Tinjauan pustaka: Rongga mulut merupakan cerminan dari status kesehatan dan banyak perubahan yang terjadi seiring peningkatan berat badan seseorang. Anak Obesitas memiliki insiden karies yang rendah jika dibandingkan

Transient electromagnetic scattering on anisotropic media

International Nuclear Information System (INIS)

Stewart, R.D.

1990-01-01

This dissertation treats the problem of transient scattering of obliquely incident electromagnetic plane waves on a stratified anisotropic dielectric slab. Scattering operators are derived for the reflective response of the medium. The internal fields are calculated. Wave splitting and invariant imbedding techniques are used. These techniques are first presented for fields normally incident on a stratified, isotropic dielectric medium. The techniques of wave splitting and invariant imbedding are applied to normally incident plane waves on an anisotropic medium. An integro-differential equation is derived for the reflective response and the direct and inverse scattering problems are discussed. These techniques are applied to the case of obliquely incident plane waves. The reflective response is derived and the direct and inverse problems discussed and compared to those for the normal incidence case. The internal fields are investigated for the oblique incidence via a Green's function approach. A numerical scheme is presented to calculate the Green's function. Finally, symmetry relations of the reflective response are discussed

Asymmetric diffusion model for oblique-incidence reflectometry

Institute of Scientific and Technical Information of China (English)

Yaqin Chen; Liji Cao; Liqun Sun

2011-01-01

A diffusion theory model induced by a line source distribution is presented for oblique-incidence reflectom-etry. By fitting to this asymmetric diffusion model, the absorption and reduced scattering coefficients μa and μ's of the turbid medium can both be determined with accuracy of 10% from the absolute profile of the diffuse reflectance in the incident plane at the negative position -1.5 transport mean free path (mfp') away from the incident point; particularly, μ's can be estimated from the data at positive positions within 0-1.0 mfp' with 10% accuracy. The method is verified by Monte Carlo simulations and experimentally tested on a phantom.%A diffusion theory model induced by a line source distribution is presented for oblique-incidence reflectometry.By fitting to this asymmetric diffusion model,the absorption and reduced scattering coefficients μa and μ's of the turbid medium can both be determined with accuracy of 10％ from the absolute profile of the diffuse reflectance in the incident plane at the negative position -1.5 transport mean free path (mfp')away from the incident point;particularly,μ's can be estimated from the data at positive positions within 0-1.0 mfp' with 10％ accuracy.The method is verified by Monte Carlo simulations and experimentally tested on a phantom.Knowledge about the optical properties,including the absorption coefficient (μa) and the reduced scattering coefficient (μ's =μs(1-g)),where μs is the scattering coefficient and g is the anisotropy factor of scattering,of biological tissues plays an important role for optical therapeutic and diagnostic techniques in medicine.

Secondary emission coefficient dependence on the angle of incidence of primary electrons on CsI and LiF layers. [0. 9 to 3 keV, mechanism

Energy Technology Data Exchange (ETDEWEB)

Shabel' nikova, A E; Yasnopol' skii, N L

1976-08-01

The angular dependence was studied of the secondary emission coefficient sigma for CsI and LiF dielectrics which have large sigma in conditions of normal incidence of primary electrons. Measurements were taken down to the angle of 85 deg for energies of primary electrons between 0.9 and 3 keV. In the whole range of angles a nonmonotonic angular dependence sigma is observed. The dependence shows itself particularly clearly for CsI at large energies of primary electrons. Such a behaviour is due to the decrease in the depth of yield of inelastically reflected electrons and to the increase in the inelastic reflection coefficient of the substance.

Generalized laws of reflection and refraction from transformation optics

OpenAIRE

Xu, Yadong; Yao, Kan; Chen, Huanyang

2012-01-01

Based on transformation optics, we introduce another set of generalized laws of reflection and refraction (differs from that of [Science 334, 333 (2011)]), through which a transformation media slab is derived as a meta-surface, producing anomalous reflection and refraction for all polarizations of incident light.

Reflections of Preservice Information Technology Teachers Regarding Cyberbullying

Directory of Open Access Journals (Sweden)

Yavuz Akbulut

2011-03-01

Full Text Available The current phenomenological study addressed the reflections of preservice information technology (IT teachers regarding their cyberbullying or victimization experiences. Fifty five preservice IT teachers at a Turkish teacher training institution were offered a lecture with the purpose of awareness-raising on cyberbullying, which was followed by the assignment of take-home reflection papers. Document analysis on reflection papers led researchers to find out underlying themes regarding participants’ cyberbullying or victimization experiences. Findings revealed that females were more likely to be victims than males. Instant messaging programs, e-mail, cell phones and online social networks were used as means to cyberbully. Varying psychological consequences of victimization incidents were reported. Noted reactions to incidents were discontinuing interaction with bullies, and seeking family, peer and legal support. Findings further implied that awareness raising activities regarding cyberbullying were likely to reduce cyberbullying instances and increase preservice teachers’ action competence

Reflections of Preservice Information Technology Teachers Regarding Cyberbullying

Directory of Open Access Journals (Sweden)

Yavuz Akbulut

2011-07-01

Full Text Available The current phenomenological study addressed the reflections of preservice information technology (IT teachers regarding their cyberbullying or victimization experiences. Fifty five preservice IT teachers at a Turkish teacher training institution were offered a lecture with the purpose of awareness-raising on cyberbullying, which was followed by the assignment of take-home reflection papers. Document analysis on reflection papers led researchers to find out underlying themes regarding participants’ cyberbullying or victimization experiences. Findings revealed that females were more likely to be victims than males. Instant messaging programs, e-mail, cell phones and online social networks were used as means to cyberbully. Varying psychological consequences of victimization incidents were reported. Noted reactions to incidents were discontinuing interaction with bullies, and seeking family, peer and legal support. Findings further implied that awareness raising activities regarding cyberbullying were likely to reduce cyberbullying instances and increase preservice teachers’ action competence.

Cervical cancer incidence in elderly women

DEFF Research Database (Denmark)

Lynge, Elsebeth; Lönnberg, Stefan; Törnberg, Sven

2017-01-01

Aim: In many countries, the age-specific pattern of cervical cancer incidence is currently bipolar with peaks at for instance 45 and 65 years of age. Consequently, a large proportion of cervical cancer cases are presently diagnosed in women above the screening age. The purpose of the study...... was to determine whether this bipolar pattern in age-specific incidence of cervical cancer reflects underlying biology or can be explained by the fact that the data come from birth cohorts with different screening histories. Methods: Combination of historical data on cervical screening and population-based cancer...... incidence data from Denmark 1943–2013, Finland and Norway 1953–2013, and Sweden 1958–2013. Results: Since the implementation of screening, the incidence of cervical cancer has decreased for each successive birth cohort. All birth cohorts showed a unipolar age-specific pattern. In unscreened women in Denmark...

Real-time visualization of melanin granules in normal human skin using combined multiphoton and reflectance confocal microscopy.

Science.gov (United States)

Majdzadeh, Ali; Lee, Anthony M D; Wang, Hequn; Lui, Harvey; McLean, David I; Crawford, Richard I; Zloty, David; Zeng, Haishan

2015-05-01

Recent advances in biomedical optics have enabled dermal and epidermal components to be visualized at subcellular resolution and assessed noninvasively. Multiphoton microscopy (MPM) and reflectance confocal microscopy (RCM) are noninvasive imaging modalities that have demonstrated promising results in imaging skin micromorphology, and which provide complementary information regarding skin components. This study assesses whether combined MPM/RCM can visualize intracellular and extracellular melanin granules in the epidermis and dermis of normal human skin. We perform MPM and RCM imaging of in vivo and ex vivo skin in the infrared domain. The inherent three-dimensional optical sectioning capability of MPM/RCM is used to image high-contrast granular features across skin depths ranging from 50 to 90 μm. The optical images thus obtained were correlated with conventional histologic examination including melanin-specific staining of ex vivo specimens. MPM revealed highly fluorescent granular structures below the dermal-epidermal junction (DEJ) region. Histochemical staining also demonstrated melanin-containing granules that correlate well in size and location with the granular fluorescent structures observed in MPM. Furthermore, the MPM fluorescence excitation wavelength and RCM reflectance of cell culture-derived melanin were equivalent to those of the granules. This study suggests that MPM can noninvasively visualize and quantify subepidermal melanin in situ. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Polarization sensitivity testing of off-plane reflection gratings

Science.gov (United States)

Marlowe, Hannah; McEntaffer, Randal L.; DeRoo, Casey T.; Miles, Drew M.; Tutt, James H.; Laubis, Christian; Soltwisch, Victor

2015-09-01

Off-Plane reflection gratings were previously predicted to have different efficiencies when the incident light is polarized in the transverse-magnetic (TM) versus transverse-electric (TE) orientations with respect to the grating grooves. However, more recent theoretical calculations which rigorously account for finitely conducting, rather than perfectly conducting, grating materials no longer predict significant polarization sensitivity. We present the first empirical results for radially ruled, laminar groove profile gratings in the off-plane mount which demonstrate no difference in TM versus TE efficiency across our entire 300-1500 eV bandpass. These measurements together with the recent theoretical results confirm that grazing incidence off-plane reflection gratings using real, not perfectly conducting, materials are not polarization sensitive.

Incidence and significance of FLT3-ITD and NPM1 mutations in patients with normal karyotype acute myeloid leukaemia.

LENUS (Irish Health Repository)

Haslam, K

2012-02-01

BACKGROUND: Acute myeloid leukaemia (AML) is a heterogeneous clonal disorder of haematopoietic progenitor cells. Approximately half of all adult AML patients have a normal karyotype (NK-AML) and an intermediate risk prognosis. AIMS: To determine the incidence and prognostic significance of NPM1 and FLT3-ITD mutations in a population of patients with NK-AML. METHODS: FLT3-ITD and NPM1 mutation status was retrospectively sought in presentation samples from 44 NK-AML patients. RESULTS: FLT3-ITD and NPM1 mutations were detected in 45.5 and 54.5% of patients, respectively, allowing stratification according to genotype. CONCLUSIONS: FLT3-ITD and NPM1 mutation status can be defined in NK-AML. Prospective screening for these mutations is advocated in all NK-AML patients, as the genotype is of clinical importance when considering treatment options including stem cell transplantation.

The differential equation of an arbitrary reflecting surface

Science.gov (United States)

Melka, Richard F.; Berrettini, Vincent D.; Yousif, Hashim A.

2018-05-01

A differential equation describing the reflection of a light ray incident upon an arbitrary reflecting surface is obtained using the law of reflection. The derived equation is written in terms of a parameter and the value of this parameter determines the nature of the reflecting surface. Under various parametric constraints, the solution of the differential equation leads to the various conic surfaces but is not generally solvable. In addition, the dynamics of the light reflections from the conic surfaces are executed in the Mathematica software. Our derivation is the converse of the traditional approach and our analysis assumes a relation between the object distance and the image distance. This leads to the differential equation of the reflecting surface.

Changing patterns of Hodgkin lymphoma incidence in Singapore

DEFF Research Database (Denmark)

Hjalgrim, H.; Seow, A.; Rostgaard, K.

2008-01-01

rates increased annually by 7.0% (95% confidence interval 3.4%-10.7%) and 3.4% (0.1%-6.8%), respectively, in men and by 13.7% (9.1%-18.6%) and 12.2% (7.8-16.8%), respectively, in women between 1968 and 2004. However, the incidence peak remained considerably lower than what can be observed in young......A bimodal age-specific incidence pattern with a relatively high proportion of cases occurring in adolescents and young adults is a hallmark of Hodgkin lymphoma (HL) epidemiology in Western industrialized countries. The young adult incidence peak is believed to reflect the association between HL...

Taxonometric Applications in Radiotherapy Incident Analysis

International Nuclear Information System (INIS)

Dunscombe, Peter B.; Ekaette, Edidiong U.; Lee, Robert C.; Cooke, David L.

2008-01-01

Recent publications in both the scientific and the popular press have highlighted the risks to which patients expose themselves when entering a healthcare system. Patient safety issues are forcing us to, not only acknowledge that incidents do occur, but also actively develop the means for assessing and managing the risks of such incidents. To do this, we ideally need to know the probability of an incident's occurrence, the consequences or severity for the patient should it occur, and the basic causes of the incident. A structured approach to the description of failure modes is helpful in terms of communication, avoidance of ambiguity, and, ultimately, decision making for resource allocation. In this report, several classification schemes or taxonomies for use in risk assessment and management are discussed. In particular, a recently developed approach that reflects the activity domains through which the patient passes and that can be used as a basis for quantifying incident severity is described. The estimation of incident severity, which is based on the concept of the equivalent uniform dose, is presented in some detail. We conclude with a brief discussion on the use of a defined basic-causes table and how adding such a table to the reports of incidents can facilitate the allocation of resources

Combining counts and incidence data: an efficient approach for estimating the log-normal species abundance distribution and diversity indices.

Science.gov (United States)

Bellier, Edwige; Grøtan, Vidar; Engen, Steinar; Schartau, Ann Kristin; Diserud, Ola H; Finstad, Anders G

2012-10-01

Obtaining accurate estimates of diversity indices is difficult because the number of species encountered in a sample increases with sampling intensity. We introduce a novel method that requires that the presence of species in a sample to be assessed while the counts of the number of individuals per species are only required for just a small part of the sample. To account for species included as incidence data in the species abundance distribution, we modify the likelihood function of the classical Poisson log-normal distribution. Using simulated community assemblages, we contrast diversity estimates based on a community sample, a subsample randomly extracted from the community sample, and a mixture sample where incidence data are added to a subsample. We show that the mixture sampling approach provides more accurate estimates than the subsample and at little extra cost. Diversity indices estimated from a freshwater zooplankton community sampled using the mixture approach show the same pattern of results as the simulation study. Our method efficiently increases the accuracy of diversity estimates and comprehension of the left tail of the species abundance distribution. We show how to choose the scale of sample size needed for a compromise between information gained, accuracy of the estimates and cost expended when assessing biological diversity. The sample size estimates are obtained from key community characteristics, such as the expected number of species in the community, the expected number of individuals in a sample and the evenness of the community.

Thermal self-focusing at oblique incidence

International Nuclear Information System (INIS)

Craxton, R.S.; McCrory, R.L.

1984-03-01

Thermal self-focusing at oblique incidence has been investigated in two-dimensional line-focus geometry using the Eulerian hydrodynamics simulation code SAGE. The laser beam interacts with a long-scale-length preformed plasma with an expontial density profiele. Questions to be addressed include: (1) What happens when a self-focusing channel reaches the turning point of the incident rays, and (2) Does the unabsorbed light return in the specular direction or back along the channel. A comparison is also made between thermal self-focusing at normal incidence in cylindrical and line-focus geometries: in cylindrical geometry the self-focusing mechanism is enhanced by the relative ease with which plasma may be expelled from a small cylindrical channel

Incident spectrum determination for time-of-flight neutron powder diffraction data analysis

International Nuclear Information System (INIS)

Hodges, J. P.

1998-01-01

Accurate characterization of the incident neutron spectrum is an important requirement for precise Rietveld analysis of time-of-flight powder neutron diffraction data. Without an accurate incident spectrum the calculated model for the measured relative intensities of individual Bragg reflections will possess systematic errors. We describe a method for obtaining an accurate numerical incident spectrum using data from a transmitted beam monitor

Extended incident-angle dependence formula of sputter yield

International Nuclear Information System (INIS)

Ono, T.; Shibata, K.; Muramoto, T.; Kenmotsu, T.; Li Z.; Kawamura, T.

2006-06-01

We extend a new semi-empirical formula for incident-angle dependence of normalized sputter yield that includes the contribution to sputter yield from the direct knock-out process that was not considered in the previously proposed one. Three parameters included in the new one are estimated for data calculated with ACAT code for D + ions incident obliquely on C, Fe and W materials in incident-energy regions from several tens of eV to 10 keV. Then, the parameters are expressed with functions of incident energy. The formula with the functions derived well reproduces that using the ACAT data in the whole energy range. (author)

Dielectric multilayer beam splitter with differential phase shift on transmission and reflection for division-of-amplitude photopolarimeter.

Science.gov (United States)

Yuan, Wenjia; Shen, Weidong; Zhang, Yueguang; Liu, Xu

2014-05-05

Dielectric multilayer beam splitter with differential phase shift on transmission and reflection for division-of-amplitude photopolarimeter (DOAP) was presented for the first time to our knowledge. The optimal parameters for the beam splitter are Tp = 78.9%, Ts = 21.1% and Δr - Δt = π/2 at 532nm at an angle of incidence of 45°. Multilayer anti-reflection coating with low phase shift was applied to reduce the backside reflection. Different design strategies that can achieve all optimal targets at the wavelength were tested. Two design methods were presented to optimize the differential phase shift. The samples were prepared by ion beam sputtering (IBS). The experimental results show good agreement with those of the design. The ellipsometric parameters of samples were measured in reflection (ψr, Δr) = (26.5°, 135.1°) and (28.2°, 133.5°), as well as in transmission (ψt, Δt) = (62.5°, 46.1°) and (63.5°, 46°) at 532.6nm. The normalized determinant of instrument matrix to evaluate the performance of samples is respectively 0.998 and 0.991 at 532.6nm.

A preliminary analysis of incident investigation reports of an integrated steel plant: some reflection.

Science.gov (United States)

Verma, A; Maiti, J; Gaikwad, V N

2018-06-01

Large integrated steel plants employ an effective safety management system and gather a significant amount of safety-related data. This research intends to explore and visualize the rich database to find out the key factors responsible for the occurrences of incidents. The study was carried out on the data in the form of investigation reports collected from a steel plant in India. The data were processed and analysed using some of the quality management tools like Pareto chart, control chart, Ishikawa diagram, etc. Analyses showed that causes of incidents differ depending on the activities performed in a department. For example, fire/explosion and process-related incidents are more common in the departments associated with coke-making and blast furnace. Similar kind of factors were obtained, and recommendations were provided for their mitigation. Finally, the limitations of the study were discussed, and the scope of the research works was identified.

Layered magnets: polarized neutron reflection studies

Energy Technology Data Exchange (ETDEWEB)

Zabel, H; Schreyer, A [Ruhr-Univ. Bochum, Lehrstuhl fuer Experimentalphysik/Festkoerperphysik, Bochum (Germany)

1996-11-01

Neutron reflectivity measurements from extended surfaces, thin films and superlattices provide information on the chemical profile parallel to the film normal, including film thicknesses, average composition and interfacial roughness parameters. Reflectivity measurements with polarized neutrons are particularly powerful for analyzing the magnetic density profiles in thin films and superlattices in addition to chemical profiles. The basic theory of polarized neutron reflectivity is provided, followed by some examples and more recent applications concerning polarized neutron reflectivity studies from exchange coupled Fe/Cr superlattices. (author) 5 figs., 13 refs.

Continuous wave terahertz reflection imaging of human colorectal tissue

Science.gov (United States)

Doradla, Pallavi; Alavi, Karim; Joseph, Cecil S.; Giles, Robert H.

2013-03-01

Continuous wave terahertz (THz) imaging has the potential to offer a safe, non-ionizing, and nondestructive medical imaging modality for delineating colorectal cancer. Fresh excisions of normal colon tissue were obtained from surgeries performed at the University of Massachusetts Medical School, Worcester. Reflection measurements of thick sections of colorectal tissues, mounted in an aluminum sample holder, were obtained for both fresh and formalin fixed tissues. The two-dimensional reflection images were acquired by using an optically pumped far-infrared molecular gas laser operating at 584 GHz with liquid Helium cooled silicon bolometer detector. Using polarizers in the experiment both co-polarized and cross-polarized remittance form the samples was collected. Analysis of the images showed the importance of understanding the effects of formalin fixation while determining reflectance level of tissue response. The resulting co- and cross-polarized images of both normal and formalin fixed tissues showed uniform terahertz response over the entire sample area. Initial measurements indicated a co-polarized reflectance of 16%, and a cross-polarized reflectance of 0.55% from fresh excisions of normal colonic tissues.

Real-time detection of dielectric anisotropy or isotropy in unconventional oil-gas reservoir rocks supported by the oblique-incidence reflectivity difference technique.

Science.gov (United States)

Zhan, Honglei; Wang, Jin; Zhao, Kun; Lű, Huibin; Jin, Kuijuan; He, Liping; Yang, Guozhen; Xiao, Lizhi

2016-12-15

Current geological extraction theory and techniques are very limited to adequately characterize the unconventional oil-gas reservoirs because of the considerable complexity of the geological structures. Optical measurement has the advantages of non-interference with the earth magnetic fields, and is often useful in detecting various physical properties. One key parameter that can be detected using optical methods is the dielectric permittivity, which reflects the mineral and organic properties. Here we reported an oblique-incidence reflectivity difference (OIRD) technique that is sensitive to the dielectric and surface properties and can be applied to characterization of reservoir rocks, such as shale and sandstone core samples extracted from subsurface. The layered distribution of the dielectric properties in shales and the uniform distribution in sandstones are clearly identified using the OIRD signals. In shales, the micro-cracks and particle orientation result in directional changes of the dielectric and surface properties, and thus, the isotropy and anisotropy of the rock can be characterized by OIRD. As the dielectric and surface properties are closely related to the hydrocarbon-bearing features in oil-gas reservoirs, we believe that the precise measurement carried with OIRD can help in improving the recovery efficiency in well-drilling process.

An investigation of the structure of plasma produced by reflected shock waves

International Nuclear Information System (INIS)

Phillips, M.G.R.; Pugatschew, A.A.

1979-05-01

Space and time resolved measurements of electron density and temperature have been made in the reflected-shock plasma produced by a Mach 20 incident shock wave propagating in argon at an initial pressure of 1.5 Torr. The peak electron density was found to decrease away from the reflecting wall in such a way that the plasma was fairly uniform at all times. Close to the reflecting wall (0.2 cm away) the measured peak electron density was close to (i.e. about 20% lower than) the predicted equilibrium value but further away (1.0 cm) it was lower by a factor 4. Possible reasons for this discrepancy are discussed. Calculations of reflected-shock plasma structure based on incident shock structure are only partially supported by available experimental evidence

Mechanisms for the reflection of light atoms from crystal surfaces at kilovolt energies

International Nuclear Information System (INIS)

Hou, M.; Robinson, M.T.

1978-01-01

The computer program MARLOWE was used to investigate the backscattering of protons from the (110) surface of a nickel crystal. Grazing incidence was considered so that anisotropic effects originated mainly from the surface region. The contribution of aligned scattering was studied by comparing the results with similar calculations for an amorphous target. Energy distributions of backscattered particles were investigated for incident energies ranging from 0.1 to 5 keV. The structure of these distributions was explained by making calculations for several target thickness. Specular reflection was found to depend on the structure of the first few atomic planes only. The (110) rows in the surface plane were responsible for focusing into surface semichannels. Focusing in these semichannels was found to be the strongest under total reflection conditions (below about 1.3 keV) while the scattering intensity from surface rows increased with increasing incident energy. The orientation of the plane of incidence was found to have large influence on the relative contributions of the reflection mechanisms involved. (orig.) [de

Oblique incidence of electron beams - comparisons between calculated and measured dose distributions

International Nuclear Information System (INIS)

Karcher, J.; Paulsen, F.; Christ, G.

2005-01-01

Clinical applications of high-energy electron beams, for example for the irradiation of internal mammary lymph nodes, can lead to oblique incidence of the beams. It is well known that oblique incidence of electron beams can alter the depth dose distribution as well as the specific dose per monitor unit. The dose per monitor unit is the absorbed dose in a point of interest of a beam, which is reached with a specific dose monitor value (DIN 6814-8[5]). Dose distribution and dose per monitor unit at oblique incidence were measured with a small-volume thimble chamber in a water phantom, and compared to both normal incidence and calculations of the Helax TMS 6.1 treatment planning system. At 4 MeV and 60 degrees, the maximum measured dose per monitor unit at oblique incidence was decreased up to 11%, whereas at 18MeV and 60 degrees this was increased up to 15% compared to normal incidence. Comparisons of measured and calculated dose distributions showed that the predicted dose at shallow depths is usually higher than the measured one, whereas it is smaller at depths beyond the depth of maximum dose. On the basis of the results of these comparisons, normalization depths and correction factors for the dose monitor value were suggested to correct the calculations of the dose per monitor unit. (orig.)

Behavior of obliquely incident vector Bessel beams at planar interfaces

KAUST Repository

Salem, Mohamed; Bagci, Hakan

2013-01-01

We investigate the behavior of full-vector electromagnetic Bessel beams obliquely incident at an interface between two electrically different media. We employ a Fourier transform domain representation of Bessel beams to determine their behavior upon reflection and transmission. This transform, which is geometric in nature, consists of elliptical support curves with complex weighting associated with them. The behavior of the scattered field at an interface is highly complex, owing to its full-vector nature; nevertheless, this behavior has a straightforward representation in the transform domain geometry. The analysis shows that the reflected field forms a different vector Bessel beam, but in general, the transmitted field cannot be represented as a Bessel beam. Nevertheless, using this approach, we demonstrate a method to propagate a Bessel beam in the refractive medium by launching a non- Bessel beam at the interface. Several interesting phenomena related to the behavior of Bessel beams are illustrated, such as polarized reflection at Brewster's angle incidence, and the Goos-Hänchen and Imbert-Federov shifts in the case of total reflection. © 2013 Optical Society of America.

Behavior of obliquely incident vector Bessel beams at planar interfaces

KAUST Repository

Salem, Mohamed

2013-01-01

We investigate the behavior of full-vector electromagnetic Bessel beams obliquely incident at an interface between two electrically different media. We employ a Fourier transform domain representation of Bessel beams to determine their behavior upon reflection and transmission. This transform, which is geometric in nature, consists of elliptical support curves with complex weighting associated with them. The behavior of the scattered field at an interface is highly complex, owing to its full-vector nature; nevertheless, this behavior has a straightforward representation in the transform domain geometry. The analysis shows that the reflected field forms a different vector Bessel beam, but in general, the transmitted field cannot be represented as a Bessel beam. Nevertheless, using this approach, we demonstrate a method to propagate a Bessel beam in the refractive medium by launching a non- Bessel beam at the interface. Several interesting phenomena related to the behavior of Bessel beams are illustrated, such as polarized reflection at Brewster\\'s angle incidence, and the Goos-Hänchen and Imbert-Federov shifts in the case of total reflection. © 2013 Optical Society of America.

Reflection of the solar wind ions at the earth's bow shock: energization

International Nuclear Information System (INIS)

Bonifazi, C.; Moreno, G.; Russell, C.T.

1983-01-01

The energies of the field-aligned proton beams observed upstream of the earth's bow shock are tested, on a statistical basis, against a simple reflection model. The comparison is carried out using both plasma and magnetic field data collected by the ISEE 2 spacecraft. The observations refer to the period from November 5 to December 20, 1977. According to this model, some of the solar wind protons incident upon the earth's shock front when reflected upstream gain energy by displacement parallel to the interplanetary electric field. The energy gained in the reflection can be described as a function of the angles between the interplanetary magnetic field, the solar wind bulk velocity, and the local shock normal. The task of finding these angles, i.e., the expected source point of the reflected ions at the earth's shock front, has been resolved using both the measured magnetic field direction and actual beam trajectory. The latter method, which takes into account the ion drift velocity, leads to a better agreement between theory and observations when far from the shock. In particular, it allows us to check the energies of the field-aligned beams even when they are observed far from the earth's bow shock (at distances up to 10-15 R/sub E/). We confirm, on a statistical basis, the test of the model recently carried out using the Los Alamos National Laboratory/Max-Planck-extraterrestrische observations on ISEE 1 and 2. We infer that reflected beams can sometimes propagate far upstream of the earth's bow shock without changing their energy properties

Effect of front and rear incident proton irradiation on silicon solar cells

Science.gov (United States)

Anspaugh, Bruce; Kachare, Ram

1987-01-01

Four solar cell types of current manufacture were irradiated through the front and rear surfaces with protons in the energy range between 1 and 10 MeV. The solar cell parameters varied for this study were cell thickness and back surface field (BSF) vs. no BSF. Some cells were irradiated at normal incidence and an equal number were irradiated with simulated isotropic fluences. The solar cell electrical characteristics were measured under simulated AM0 illumination after each fluence. Using the normal incidence data, proton damage coefficients were computed for all four types of cells for both normal and omnidirectional radiation fields. These were found to compare well with the omnidirectional damage coefficients derived directly from the rear-incidence radiation data. Similarly, the rear-incidence omnidirectional radiation data were used to compute appropriate damage coefficients. A method for calculating the effect of a spectrum of energies is derived from these calculations. It is suitable for calculating the degradation of cells in space when they have minimal rear-surface shielding.

An isodose shift technique for obliquely incident electron beams

International Nuclear Information System (INIS)

Ulin, K.; Sternick, E.S.

1989-01-01

It is well known that when an electron beam is incident obliquely on the surface of a phantom, the depth dose curve measured normal to the surface is shifted toward the surface. Based on geometrical arguments alone, the depth of the nth isodose line for an electron beam incident at an angle θ should be equal to the product of cos θ and the depth of the nth isodose line at normal incidence. This method, however, ignores the effects of scatter and can lead to significant errors in isodose placement for beams at large angles of incidence. A semi-empirical functional relationship and a table of isodose shift factors have been developed with which one may easily calculate the depth of any isodose line for beams at incident angles of 0 degree to 60 degree. The isodose shift factors are tabulated in terms of beam energy (6--22 MeV) and isodose line (10%--90%) and are shown to be relatively independent of beam size and incident angle for angles <60 degree. Extensive measurements have been made on a Varian Clinac 2500 linear accelerator with a parallel-plate chamber and polystyrene phantom. The dependence of the chamber response on beam angulation has been checked, and the scaling factor of the polystyrene phantom has been determined to be equal to 1.00

Total internal reflection second-harmonic generation: probing the alkane water interface

International Nuclear Information System (INIS)

Conboy, J.C.; Daschbach, J.L.; Richmond, G.L.

1994-01-01

Total internal reflection Second-Harmonic Generation (SHG) has been used to study a series of neat n-alkane/water interfaces. Polarization and incident angular-dependent measurements of the SH response show good agreement with theoretical predictions. Analysis of the incident and polarization angular-dependent SH response allows for determination of the nonlinear optical properties of molecules comprising the interfacial region. Based on Kleinman symmetry, the measured surface nonlinear susceptibilities suggest a high degree of interfacial order for octane and decane with less order indicated by the odd carbon n-alkanes examined, heptane and nonane. The SH response in reflection and transmission has been measured under a Total Internal Reflection (TIR) of the fundamental. The measured nonlinear susceptibilities in each case are found to be identical. (orig.)

Reflection and transmission of ion acoustic waves from a plasma discontinuity

International Nuclear Information System (INIS)

Gary, S.P.; Alexeff, I.; Bloomberg, H.W.

1975-01-01

Transmission and reflection coefficients are calculated for an ion acoustic wave incident from the upstream direction upon a plasma discontinuity of width much less than the wavelength. In the limit of an infinitely strong discontinuity there is complete in phase reflection. (U.S.)

Strength of Gamma Rhythm Depends on Normalization

Science.gov (United States)

Ray, Supratim; Ni, Amy M.; Maunsell, John H. R.

2013-01-01

Neuronal assemblies often exhibit stimulus-induced rhythmic activity in the gamma range (30–80 Hz), whose magnitude depends on the attentional load. This has led to the suggestion that gamma rhythms form dynamic communication channels across cortical areas processing the features of behaviorally relevant stimuli. Recently, attention has been linked to a normalization mechanism, in which the response of a neuron is suppressed (normalized) by the overall activity of a large pool of neighboring neurons. In this model, attention increases the excitatory drive received by the neuron, which in turn also increases the strength of normalization, thereby changing the balance of excitation and inhibition. Recent studies have shown that gamma power also depends on such excitatory–inhibitory interactions. Could modulation in gamma power during an attention task be a reflection of the changes in the underlying excitation–inhibition interactions? By manipulating the normalization strength independent of attentional load in macaque monkeys, we show that gamma power increases with increasing normalization, even when the attentional load is fixed. Further, manipulations of attention that increase normalization increase gamma power, even when they decrease the firing rate. Thus, gamma rhythms could be a reflection of changes in the relative strengths of excitation and normalization rather than playing a functional role in communication or control. PMID:23393427

Use of an ultrasonic reflectance technique to examine bubble size changes in dough

Science.gov (United States)

Strybulevych, A.; Leroy, V.; Shum, A. L.; Koksel, H. F.; Scanlon, M. G.; Page, J. H.

2012-12-01

Bread quality largely depends on the manner in which bubbles are created and manipulated in the dough during processing. We have developed an ultrasonic reflectance technique to monitor bubbles in dough, even at high volume fractions, where near the bubble resonances it is difficult to make measurements using transmission techniques. A broadband transducer centred at 3.5 MHz in a normal incidence wave reflection set-up is used to measure longitudinal velocity and attenuation from acoustic impedance measurements. The technique is illustrated by examining changes in bubbles in dough due to two very different physical effects. In dough made without yeast, a peak in attenuation due to bubble resonance is observed at approximately 2 MHz. This peak diminishes rapidly and shifts to lower frequencies, indicative of Ostwald ripening of bubbles within the dough. The second effect involves the growth of bubble sizes due to gas generated by yeast during fermentation. This process is experimentally challenging to investigate with ultrasound because of very high attenuation. The reflectance technique allows the changes of the velocity and attenuation during fermentation to be measured as a function of frequency and time, indicating bubble growth effects that can be monitored even at high volume fractions of bubbles.

Use of an ultrasonic reflectance technique to examine bubble size changes in dough

International Nuclear Information System (INIS)

Strybulevych, A; Leroy, V; Page, J H; Shum, A L; Koksel, H F; Scanlon, M G

2012-01-01

Bread quality largely depends on the manner in which bubbles are created and manipulated in the dough during processing. We have developed an ultrasonic reflectance technique to monitor bubbles in dough, even at high volume fractions, where near the bubble resonances it is difficult to make measurements using transmission techniques. A broadband transducer centred at 3.5 MHz in a normal incidence wave reflection set-up is used to measure longitudinal velocity and attenuation from acoustic impedance measurements. The technique is illustrated by examining changes in bubbles in dough due to two very different physical effects. In dough made without yeast, a peak in attenuation due to bubble resonance is observed at approximately 2 MHz. This peak diminishes rapidly and shifts to lower frequencies, indicative of Ostwald ripening of bubbles within the dough. The second effect involves the growth of bubble sizes due to gas generated by yeast during fermentation. This process is experimentally challenging to investigate with ultrasound because of very high attenuation. The reflectance technique allows the changes of the velocity and attenuation during fermentation to be measured as a function of frequency and time, indicating bubble growth effects that can be monitored even at high volume fractions of bubbles.

EAP-based critical incident stress management: utilization of a practice-based assessment of incident severity level in responding to workplace trauma.

Science.gov (United States)

DeFraia, Gary S

2013-01-01

Central to the field of trauma psychology is assessment of the impact of critical incidents on individuals, as measured by individual symptoms of stress. Accordingly, the trauma literature reflects a proliferation of clinical impact of event scales. Workplace incidents however, affect not only individual employees, but also work organizations, requiring a multi-level response. Critical incident stress management (CISM) is the most prevalent multi-level incident response strategy utilized by organizations, often through specialized CISM units operating within their employee assistance programs (EAPs). While EAP-based CISM units seeks to support both individuals and organizations, studies focused on individual stress dominate the literature, mirroring assessment scales that tend to emphasize clinical as opposed to organizational practice. This research contributes to less-prevalent studies exploring incident characteristics as disruptive to organizations, rather than clinical symptoms as disruptive to individuals. To measure incident disruption, an EAP-based CISM unit developed a critical incident severity scale. By analyzing this unit's extensive practice database, this exploratory study examines how critical incident severity level varies among various types of incidents. Employing the methodology of clinical data mining, this practice-based research generates evidence-informed practice recommendations in the areas of EAP-based CISM intake assessment, organizational consultation and incident response planning.

Low reflectance radio frequency load

Science.gov (United States)

Ives, R. Lawrence; Mizuhara, Yosuke M

2014-04-01

A load for traveling microwave energy has an absorptive volume defined by cylindrical body enclosed by a first end cap and a second end cap. The first end cap has an aperture for the passage of an input waveguide with a rotating part that is coupled to a reflective mirror. The inner surfaces of the absorptive volume consist of a resistive material or are coated with a coating which absorbs a fraction of incident RF energy, and the remainder of the RF energy reflects. The angle of the reflector and end caps is selected such that reflected RF energy dissipates an increasing percentage of the remaining RF energy at each reflection, and the reflected RF energy which returns to the rotating mirror is directed to the back surface of the rotating reflector, and is not coupled to the input waveguide. Additionally, the reflector may have a surface which generates a more uniform power distribution function axially and laterally, to increase the power handling capability of the RF load. The input waveguide may be corrugated for HE11 mode input energy.

Quantitative survey radiographic evaluation of the lumbosacral spine of normal dogs and dogs with degenerative lumbosacral stenosis

International Nuclear Information System (INIS)

Mattoon, J.S.; Koblik, P.D.

1993-01-01

Survey radiographic studies of the lumbosacral region for 93 normal dogs and for 26 dogs with confirmed degenerative lumbosacral stenosis were reviewed. Normal dogs were divided into 9 groups based on age and body weight. For normal dogs, increasing age and body weight were associated with a decreased ability to extend the lumbosacral joint and with increased incidence and severity of spondylosis. Transitional lumbosacral vertebrae and evidence of lumbosacral disc space collapse were very infrequent findings, and the pivot point for lumbosacral motion was consistently centered over the lumbosacral disc space. Relative to an age/weight matched sub-population of normal dogs, dogs with degenerative lumbosacral stenosis had similar mean normalized lumbosacral vertebral canal height, larger mean neutral lumbosacral angle, decreased extension of the lumbosacral joint, increased flexion of the lumbosacral joint, reduced lumbosacral range of motion, increased lumbosacral dynamic malalignment, higher incidence and severity of spondylosis, higher incidence of transitional vertebrae, and higher incidence of lumbosacral disc space collapse. A logistic model based strictly on radiographic parameters was able to discriminate normal from affected dogs with an overall accuracy rate of 86%

Using mid-Infrared External Reflectance Spectroscopy to Distinguish Between Different Commercially Produced Poly[Methyl MethAcrylate] (PMMA) Samples - A Null Result

Science.gov (United States)

Fajardo, Mario; Neel, Christopher; Lacina, David

2017-06-01

We report (null) results of experiments testing the hypothesis that mid-infrared (mid-IR) spectroscopy can be used to distinguish samples of poly[methyl methacrylate] (PMMA) obtained from different commercial suppliers. This work was motivated by the desire for a simple non-destructive and non-invasive test for pre-sorting PMMA samples prior to use in shock and high-strain-rate experiments, where PMMA is commonly used as a standard material. We discuss: our choice of mid-IR external reflectance spectroscopy, our approach to recording reflectance spectra at near-normal (θ = 0 + / - 5 degree) incidence and for extracting the wavelength-weighted absorption spectrum from the raw reflectance data via a Kramers-Krönig analysis. We employ extensive signal, which necessitates adopting a special experimental protocol to mitigate the effects of instrumental drift. Finally, we report spectra of three PMMA samples with different commercial pedigrees, and show that they are virtually identical (+ / - 1 % error, 95% confidence); obviating the use of mid-IR reflectance spectroscopy to tell the samples apart.

Neutron reflectivity

Directory of Open Access Journals (Sweden)

Cousin Fabrice

2015-01-01

Full Text Available The specular neutron reflectivity is a technique enabling the measurement of neutron scattering length density profile perpendicular to the plane of a surface or an interface, and thereby the profile of chemical composition. The characteristic sizes that are probed range from around 5 Å up 5000 Å. It is a scattering technique that averages information on the entire surface and it is therefore not possible to obtain information within the plane of the interface. The specific properties of neutrons (possibility of tuning the contrast by isotopic substitution, sensitivity to magnetism, negligible absorption, low energy of the incident neutrons makes it particularly interesting in the fields of soft matter, biophysics and magnetic thin films. This course is a basic introduction to the technique and does not address the magnetic reflectivity. It is composed of three parts describing respectively its principle and its formalism, the experimental aspects of the method (spectrometers, samples and two examples related to the materials for energy.

Study of the reflective behaviour of carbon fibres reinforced polymer composite up to 450°C

Science.gov (United States)

Le Louët, Violaine; Rousseau, Benoit; Le Corre, Steven; Boyard, Nicolas; Tardif, Xavier; Delmas, Jérôme; Delaunay, Didier

2017-10-01

This study aims at characterizing the radiative properties of a carbon/PEEK composite, a material known to be opaque for usual thicknesses and to scatter thermal radiation in the infrared spectral range. The scattering behaviour is probed here at room temperature with a variable angle reflectivity unit linked to a Fourier Transform InfraRed Spectrometer (0.6-25 µm), for different fibre orientations and various angles of incidence. Moreover, in order to study the influence of temperature, particularly of the polymer matrix melting, a compact cell, based on a customized resistive heater, is adapted to the sample compartment of the spectrometer to measure the thermal dependency of the normal reflectivity. The new sample holder can be used at a temperature ranging between 20 and 450°C and with a temperature stability lower than 0.1 K. For the carbon/PEEK composite, the effects of the polymer phase change are observed to be small, confirming the predominant role of carbon on those composites optical properties.

Reflection characterization of nano-sized dielectric structure in Morpho butterfly wings

Science.gov (United States)

Zhu, Dong

2017-10-01

Morpho butterflies living in Central and South America are well-known for their structural-colored blue wings. The blue coloring originates from the interaction of light with nano-sized dielectric structures that are equipped on the external surface of scales covering over their wings. The high-accuracy nonstandard finite-difference time domain (NS-FDTD) method is used to investigate the reflection characterization from the nanostructures. In the NS-FDTD calculation, a computational model is built to mimic the actual tree-like multilayered structures wherever possible using the hyperbolic tangent functions. It is generally known that both multilayer interference and diffraction grating phenomena can occur when light enters the nano-sized multilayered structure. To answer the question that which phenomenon is mainly responsible for the blue coloring, the NS-FDTD calculation is performed under various incidence angles at wavelengths from 360 to 500 nm. The calculated results at one incident wavelength under different incidence angles are visualized in a two-dimensional mapping image, where horizontal and vertical axes are incidence and reflection angles, respectively. The images demonstrate a remarkable transition from a ring-like pattern at shorter wavelengths to a retro-reflection pattern at longer wavelengths. To clarify the origin of the pattern transition, the model is separated into several simpler parts and compared their mapping images with the theoretical diffraction calculations. It can be concluded that the blue coloring at longer wavelengths is mainly caused by the cooperation of multilayer interference and retro-reflection while the effect of diffraction grating is predominant at shorter wavelengths.

Supra-salt normal fault growth during the rise and fall of a diapir: Perspectives from 3D seismic reflection data, Norwegian North Sea

Science.gov (United States)

Tvedt, Anette B. M.; Rotevatn, Atle; Jackson, Christopher A.-L.

2016-10-01

Normal faulting and the deep subsurface flow of salt are key processes controlling the structural development of many salt-bearing sedimentary basins. However, our detailed understanding of the spatial and temporal relationship between normal faulting and salt movement is poor due to a lack of natural examples constraining their geometric and kinematic relationship in three-dimensions. To improve our understanding of these processes, we here use 3D seismic reflection and borehole data from the Egersund Basin, offshore Norway, to determine the structure and growth of a normal fault array formed during the birth, growth and decay of an array of salt structures. We show that the fault array and salt structures developed in response to: (i) Late Triassic-to-Middle Jurassic extension, which involved thick-skinned, sub-salt and thin-skinned supra-salt faulting with the latter driving reactive diapirism; (ii) Early Cretaceous extensional collapse of the walls; and (iii) Jurassic-to-Neogene, active and passive diapirism, which was at least partly coeval with and occurred along-strike from areas of reactive diapirism and wall collapse. Our study supports physical model predictions, showcasing a three-dimensional example of how protracted, multiphase salt diapirism can influence the structure and growth of normal fault arrays.

REX - a program for the analysis of X-ray reflectivity data: user guide and programmer manual

International Nuclear Information System (INIS)

Crabb, T.A.; Gibson, P.N.

1992-12-01

A FORTRAN program REX, which has been developed to facilitate the interpretation of X-ray reflectivity data, is described. The program allows the simulation of reflectivity profiles as a function of either incident angle or of energy. Factors such as anomalous dispersion, and surface and interface roughness are taken into account in the model. In addition, experimental data of reflectivity as a function of incident angle can be matched to user-supplied theoretical parameters by a least-squares refinement procedure. Experimental reflectivity data recorded at several X-ray wavelengths can be analysed simultaneously, thus eliminating certain experimental errors. (author)

Unpacking In-Service EFL Teachers' Critical Incidents: The Case of Iran

Science.gov (United States)

Atai, Mahmood Reza; Nejadghanbar, Hassan

2016-01-01

Despite the importance of reflection on critical incidents (CIs), there are only a few studies in ELT literature addressing English language teachers' CIs (Farrell, 2008). Accordingly, this study was conducted to explore and discuss how six in-service EFL teachers reflected on and reported their CIs. In so doing, the participant teachers reflected…

Geometrically distributed one-dimensional photonic crystals for light-reflection in all angles.

Science.gov (United States)

Alagappan, G; Wu, P

2009-07-06

We demonstrate that a series of one-dimensional photonic crystals made of any dielectric materials, with the periods are distributed in a geometrical progression of a common ratio, r rc (theta,P), where rc is a structural parameter that depends on the angle of incidence, theta, and polarization, P, is capable of blocking light of any spectral range. If an omni-directional reflection is desired for all polarizations and for all incident angles smaller than thetao, then r rc (theta(o),p), where p is the polarization with the electric field parallel to the plane of incidence. We present simple and formula like expressions for rc, width of the bandgap, and minimum number of photonic crystals to achieve a perfect light reflection.

Pursuing Normality

DEFF Research Database (Denmark)

Madsen, Louise Sofia; Handberg, Charlotte

2018-01-01

implying an influence on whether to participate in cancer survivorship care programs. Because of "pursuing normality," 8 of 9 participants opted out of cancer survivorship care programming due to prospects of "being cured" and perceptions of cancer survivorship care as "a continuation of the disease......BACKGROUND: The present study explored the reflections on cancer survivorship care of lymphoma survivors in active treatment. Lymphoma survivors have survivorship care needs, yet their participation in cancer survivorship care programs is still reported as low. OBJECTIVE: The aim of this study...... was to understand the reflections on cancer survivorship care of lymphoma survivors to aid the future planning of cancer survivorship care and overcome barriers to participation. METHODS: Data were generated in a hematological ward during 4 months of ethnographic fieldwork, including participant observation and 46...

Reflectivity and thickness analysis of epiretinal membranes using spectral-domain optical coherence tomography

Directory of Open Access Journals (Sweden)

Ajay E. Kuriyan

2016-01-01

Full Text Available AIM: To compare thickness and reflectivity spectral domain optical coherence tomography (SD-OCT findings in patients with idiopathic epiretinal membranes (ERMs, before and after ERM peeling surgery, with normal controls. METHODS: A retrospective study analyzed SD-OCTs of eyes with ERMs undergoing ERM peeling surgery by one surgeon from 2008 to 2010 and normal control eyes. SD-OCTs were analyzed using a customized algorithm to measure reflectivity and thickness. The relationship between the SD-OCT findings and best corrected visual acuity (BCVA outcomes was also studied. RESULTS: Thirty-four ERM eyes and 12 normal eyes were identified. Preoperative eyes had high reflectivity and thickness of the group of layers from the internal limiting membrane (ILM to the retinal pigment epithelium (RPE and the group of layers from the ILM to the external limiting membrane (ELM. The values of reflectivity of these two groups of layers decreased postoperatively, but were still higher than normal eyes. In contrast, preoperative eyes had lower reflectivity of two 10×15 pixel regions of interest (ROIs incorporating: 1 ELM + outer nuclear layer (ONL and 2 photoreceptor layer (PRL + RPE, compared to controls. The values of reflectivity of these ROIs increased postoperatively, but were still lower than normal controls. A larger improvement in BCVA postoperatively was correlated with a greater degree of abnormal preoperative reflectivity and thickness findings. CONCLUSION: Quantitative differences in reflectivity and thickness between preoperative, postoperative, and normal SD-OCTs allow assessment of changes in the retina secondary to ERM. Our study identified hyperreflective inner retina changes and hyporeflective outer retina changes in patients with ERMs. SD-OCT quantitative measures of reflectivity and/or thickness of specific groups of retinal layers and/or ROIs correlate with improvement in BCVA.

Incident Duration Modeling Using Flexible Parametric Hazard-Based Models

Directory of Open Access Journals (Sweden)

Ruimin Li

2014-01-01

Full Text Available Assessing and prioritizing the duration time and effects of traffic incidents on major roads present significant challenges for road network managers. This study examines the effect of numerous factors associated with various types of incidents on their duration and proposes an incident duration prediction model. Several parametric accelerated failure time hazard-based models were examined, including Weibull, log-logistic, log-normal, and generalized gamma, as well as all models with gamma heterogeneity and flexible parametric hazard-based models with freedom ranging from one to ten, by analyzing a traffic incident dataset obtained from the Incident Reporting and Dispatching System in Beijing in 2008. Results show that different factors significantly affect different incident time phases, whose best distributions were diverse. Given the best hazard-based models of each incident time phase, the prediction result can be reasonable for most incidents. The results of this study can aid traffic incident management agencies not only in implementing strategies that would reduce incident duration, and thus reduce congestion, secondary incidents, and the associated human and economic losses, but also in effectively predicting incident duration time.

Incidence of inguinal hernia in children with congenital cerebral palsy

DEFF Research Database (Denmark)

Reimers, J I; Latocha, J E

1990-01-01

The incidence of inguinal hernia among 247 children with cerebral palsy was ascertained. During the first year of life, 20 of the 153 boys developed hernia, as did one of the 94 girls. Among boys with birthweights of 1000 to 2000g the incidence was 31 per cent, which is twice the rate for normal...

Occurrence and Magnitude of High Reflectance Materials on the Moon

Science.gov (United States)

Nuno, R. G.; Boyd, A. K.; Robinson, M. S.

2013-12-01

We utilize a Lunar Reconnaissance Orbiter (LRO) Wide Angle Camera (WAC) 643 nm photometrically normalized (30°, 0°, 30°; i, e, g) reflectance map to investigate the occurrence and origin of high reflectance materials on the Moon. Compositional differences (mainly iron and titanium content) and maturity state (e.g. Copernican crater rays and swirls) are the predominant factors affecting reflectance variations observed on the Moon. Therefore, comparing reflectance values of different regions yields insight into the composition and relative exposure age of lunar materials. But an accurate comparison requires precise reflectance values normalized across every region being investigated. The WAC [1] obtains monthly near-global ground coverage, each month's observations acquired with different lighting conditions. Boyd et al. [2] utilized a geologically homogeneous subset [0°N to 90°N, 146°E to 148°E] of the WAC observations to determine an equation that describes how viewing and lighting angles affect reflectance values. A normalized global reflectance map was generated by applying the local empirical solution globally, with photometric angles derived from the WAC Global Lunar Digital Terrain Model (DTM)(GLD100) [3]. The GLD100 enables accurate correction of reflectance differences caused by local topographic undulations at the scale of 300 meters. We compare reflectance values across the Moon within 80°S to 80°N latitude. The features with the highest reflectance are steep crater walls within Copernican aged craters, such as the walls of Giordano Bruno, which have normalized reflectance values up to 0.35. Near-impact ejecta of some craters have high reflectance values, such as Virtanen (0.22). There are also broad relatively flat features with high reflectance, such as the 900-km Thales-Compton region (0.24) and the 600-km extent of Anaxagoras (Copernican age) ejecta (0.20). Since the interior of Anaxagoras contains occurrences of pure anorthosite [4], the high

Ultrasmooth metallic films with buried nanostructures for backside reflection-mode plasmonic biosensing

Energy Technology Data Exchange (ETDEWEB)

Lindquist, N.C.; Johnson, T.W.; Jose, J.; Otto, L.M. [Laboratory of Nanostructures and Biosensing, Department of Electrical and Computer Engineering, University of Minnesota, Minneapolis, MN 55455 (United States); Oh, S.H. [Laboratory of Nanostructures and Biosensing, Department of Electrical and Computer Engineering, University of Minnesota, Minneapolis, MN 55455 (United States); Department of Biophysics and Chemical Biology, Seoul National University, Seoul, 151-747 (Korea, Republic of)

2012-11-15

A new plasmonic device architecture based on ultrasmooth metallic surfaces with buried plasmonic nanostructures is presented. Using template-stripping techniques, ultrathin gold films with less than 5 Aa surface roughness are optically coupled to an arbitrary arrangement of buried metallic gratings, rings, and nanodots. As a prototypical example, linear plasmonic gratings buried under an ultrasmooth 20 nm thick gold surface for biosensing are presented. The optical illumination and collection are completely decoupled from the microfluidic delivery of liquid samples due to the backside, reflection-mode geometry. This allows for sensing with opaque or highly scattering liquids. With the buried nanostructure design, high sensitivity and decoupled backside (reflective) optical access are maintained, as with traditional prism-based surface plasmon resonance (SPR) sensors. In addition, the benefits offered by nanoplasmonic sensors such as spectral tunability and high-resolution, wide-field SPR imaging with normal-incidence epi-illumination that is simple to construct and align are gained as well. Beyond sensing, the buried plasmonic nanostructures with ultrasmooth metallic surfaces can benefit nanophotonic waveguides, surface-enhanced spectroscopy, nanolithography, and optical trapping. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Aplanatic grazing incidence diffraction grating: a new optical element

International Nuclear Information System (INIS)

Hettrick, M.C.

1986-01-01

We present the theory of a grazing incidence reflection grating capable of imaging at submicron resolution. The optic is mechanically ruled on a spherical or cylindrical surface with varied groove spacings, delivering diffraction-limited response and a wide field of view at a selected wavelength. Geometrical aberrations are calculated on the basis of Fermat's principle, revealing significant improvements over a grazing incidence mirror. Aplanatic and quasi-aplanatic versions of the grating have applications in both imaging and scanning microscopes, microprobes, collimators, and telescopes. A 2-D crossed system of such gratings, similar to the grazing incidence mirror geometry of Kirkpatrick and Baez, could potentially provide spatial resolutions of --200 A

Acoustic wave spread in superconducting-normal-superconducting sandwich

International Nuclear Information System (INIS)

Urushadze, G.I.

2004-01-01

The acoustic wave spread, perpendicular to the boundaries between superconducting and normal metals in superconducting-normal-superconducting (SNS) sandwich has been considered. The alternate current flow sound induced by the Green function method has been found and the coefficient of the acoustic wave transmission through the junction γ=(S 1 -S 2 )/S 1 , (where S 1 and S 2 are average energy flows formed on the first and second boundaries) as a function of the phase difference between superconductors has been investigated. It is shown that while the SNS sandwich is almost transparent for acoustic waves (γ 0 /τ), n=0,1,2, ... (where τ 0 /τ is the ratio of the broadening of the quasiparticle energy levels in impurity normal metal as a result of scattering of the carriers by impurities 1/τ to the spacing between energy levels 1/τ 0 ), γ=2, (S 2 =-S 1 ), which corresponds to the full reflection of the acoustic wave from SNS sandwich. This result is valid for the limit of a pure normal metal but in the main impurity case there are two amplification and reflection regions for acoustic waves. The result obtained shows promise for the SNS sandwich as an ideal mirror for acoustic wave reflection

Real-Time, Label-Free Detection of Biomolecular Interactions in Sandwich Assays by the Oblique-Incidence Reflectivity Difference Technique

Directory of Open Access Journals (Sweden)

Yung-Shin Sun

2014-12-01

Full Text Available One of the most important goals in proteomics is to detect the real-time kinetics of diverse biomolecular interactions. Fluorescence, which requires extrinsic tags, is a commonly and widely used method because of its high convenience and sensitivity. However, in order to maintain the conformational and functional integrality of biomolecules, label-free detection methods are highly under demand. We have developed the oblique-incidence reflectivity difference (OI-RD technique for label-free, kinetic measurements of protein-biomolecule interactions. Incorporating the total internal refection geometry into the OI-RD technique, we are able to detect as low as 0.1% of a protein monolayer, and this sensitivity is comparable with other label-free techniques such as surface plasmon resonance (SPR. The unique advantage of OI-RD over SPR is no need for dielectric layers. Moreover, using a photodiode array as the detector enables multi-channel detection and also eliminates the over-time signal drift. In this paper, we demonstrate the applicability and feasibility of the OI-RD technique by measuring the kinetics of protein-protein and protein-small molecule interactions in sandwich assays.

Design of multi-layer anti-reflection coating for terrestrial solar panel ...

Indian Academy of Sciences (India)

To date, there is no ideal anti-reflection (AR) coating available on solar glass which can effectively transmit the incident light within the visible wavelength range. However, there is a need to develop multifunctional coatingwith superior anti-reflection properties and self-cleaning ability meant to be used for solar glass panels.

Effects of Different LiDAR Intensity Normalization Methods on Scotch Pine Forest Leaf Area Index Estimation

Directory of Open Access Journals (Sweden)

YOU Haotian

2018-02-01

Full Text Available The intensity data of airborne light detection and ranging (LiDAR are affected by many factors during the acquisition process. It is of great significance for the normalization and application of LiDAR intensity data to study the effective quantification and normalization of the effect from each factor. In this paper, the LiDAR data were normalized with range, angel of incidence, range and angle of incidence based on radar equation, respectively. Then two metrics, including canopy intensity sum and ratio of intensity, were extracted and used to estimate forest LAI, which was aimed at quantifying the effects of intensity normalization on forest LAI estimation. It was found that the range intensity normalization could improve the accuracy of forest LAI estimation. While the angle of incidence intensity normalization did not improve the accuracy and made the results worse. Although the range and incidence angle normalized intensity data could improve the accuracy, the improvement was less than the result of range intensity normalization. Meanwhile, the differences between the results of forest LAI estimation from raw intensity data and normalized intensity data were relatively big for canopy intensity sum metrics. However, the differences were relatively small for the ratio of intensity metrics. The results demonstrated that the effects of intensity normalization on forest LAI estimation were depended on the choice of affecting factor, and the influential level is closely related to the characteristics of metrics used. Therefore, the appropriate method of intensity normalization should be chosen according to the characteristics of metrics used in the future research, which could avoid the waste of cost and the reduction of estimation accuracy caused by the introduction of inappropriate affecting factors into intensity normalization.

Structure and Dissipation Characteristics of an Electron Diffusion Region Observed by MMS During a Rapid, Normal-Incidence Magnetopause Crossing

Science.gov (United States)

Torbert, R. B.; Burch, J. L.; Argall, M. R.; Alm, L.; Farrugia, C. J.; Forbes, T. G.; Giles, B. L.; Rager, A.; Dorelli, J.; Strangeway, R. J.; Ergun, R. E.; Wilder, F. D.; Ahmadi, N.; Lindqvist, P.-A.; Khotyaintsev, Y.

2017-12-01

On 22 October 2016, the Magnetospheric Multiscale (MMS) spacecraft encountered the electron diffusion region (EDR) when the magnetosheath field was southward, and there were signatures of fast reconnection, including flow jets, Hall fields, and large power dissipation. One rapid, normal-incidence crossing, during which the EDR structure was almost stationary in the boundary frame, provided an opportunity to observe the spatial structure for the zero guide field case of magnetic reconnection. The reconnection electric field was determined unambiguously to be 2-3 mV/m. There were clear signals of fluctuating parallel electric fields, up to 6 mV/m on the magnetosphere side of the diffusion region, associated with a Hall-like parallel current feature on the electron scale. The width of the main EDR structure was determined to be 2 km (1.8 de). Although the MMS spacecraft were in their closest tetrahedral separation of 8 km, the divergences and curls for these thin current structures could therefore not be computed in the usual manner. A method is developed to determine these quantities on a much smaller scale and applied to compute the normal component of terms in the generalized Ohm's law for the positions of each individual spacecraft (not a barocentric average). Although the gradient pressure term has a qualitative dependence that follows the observed variation of E + Ve × B, the quantitative magnitude of these terms differs by more than a factor of 2, which is shown to be greater than the respective errors. Thus, future research is required to find the manner in which Ohm's law is balanced.

Quasiparticle transport properties of mesoscopic wires containing normal-metal/superconductor/normal-metal proximity junctions

International Nuclear Information System (INIS)

Kim, Nam; Kim, Kijoon; Lee, Hu Jong; Lee, Seongjae; Yuk, Jong Seol; Park, Kyoung Wan; Lee, El Hang

1997-01-01

We measured the differential resistance dV/dI of mesoscopic normal-metal/superconductor/normal-metal (N-S-N) junctions. At low temperatures (T PbIn /e, where Δ PbIn is the gap energy of superconducting Pb-In, and at a higher bias V c . The zero-bias dip is supposed to originate from Andreev reflections of quasiparticles and the peak near 2Δ PbIn /e from the formation of a standing-wave mode of quasiparticles inside the superconducting potential barrier. We attribute the peaks at V c to a transition of the superconducting region to the normal state as the current exceeds the critical current I c of S

Solar flux incident on an orbiting surface after reflection from a planet

Science.gov (United States)

Modest, M. F.

1980-01-01

Algorithms describing the solar radiation impinging on an infinitesimal surface after reflection from a gray and diffuse planet are derived. The following conditions apply: only radiation from the sunny half of the planet is taken into account; the radiation must fall on the top of the orbiting surface, and radiation must come from that part of the planet that can be seen from the orbiting body. A simple approximate formula is presented which displays excellent accuracy for all significant situations, with an error which is always less than 5% of the maximum possible reflected flux. Attention is also given to solar albedo flux on a surface directly facing the planet, the influence of solar position on albedo flux, and to solar albedo flux as a function of the surface-planet tilt angle.

Transmission versus reflectance spectroscopy for quantitation

Science.gov (United States)

Gardner, Craig M.

2018-01-01

The objective of this work was to compare the accuracy of analyte concentration estimation when using transmission versus diffuse reflectance spectroscopy of a scattering medium. Monte Carlo ray tracing of light through the medium was used in conjunction with pure component absorption spectra and Beer-Lambert absorption along each ray's pathlength to generate matched sets of pseudoabsorbance spectra, containing water and six analytes present in skin. PLS regression models revealed an improvement in accuracy when using transmission compared to reflectance for a range of medium thicknesses and instrument noise levels. An analytical expression revealed the source of the accuracy degradation with reflectance was due both to the reduced collection efficiency for a fixed instrument etendue and to the broad pathlength distribution that detected light travels in the medium before exiting from the incident side.

Hewlett-Packard's Approaches to Full Color Reflective Displays

Science.gov (United States)

Gibson, Gary

2012-02-01

Reflective displays are desirable in applications requiring low power or daylight readability. However, commercial reflective displays are currently either monochrome or capable of only dim color gamuts. Low cost, high-quality color technology would be rapidly adopted in existing reflective display markets and would enable new solutions in areas such as retail pricing and outdoor digital signage. Technical breakthroughs are required to enable bright color gamuts at reasonable cost. Pixel architectures that rely on pure reflection from a single layer of side-by-side primary-color sub-pixels use only a fraction of the display area to reflect incident light of a given color and are, therefore, unacceptably dark. Reflective devices employing stacked color primaries offer the possibility of a somewhat brighter color gamut but can be more complex to manufacture. In this talk, we describe HP's successes in addressing these fundamental challenges and creating both high performance stacked-primary reflective color displays as well as inexpensive single layer prototypes that provide good color. Our stacked displays utilize a combination of careful light management techniques, proprietary high-contrast electro-optic shutters, and highly transparent active-matrix TFT arrays based on transparent metal oxides. They also offer the possibility of relatively low cost manufacturing through roll-to-roll processing on plastic webs. To create even lower cost color displays with acceptable brightness, we have developed means for utilizing photoluminescence to make more efficient use of ambient light in a single layer device. Existing reflective displays create a desired color by reflecting a portion of the incident spectrum while absorbing undesired wavelengths. We have developed methods for converting the otherwise-wasted absorbed light to desired wavelengths via tailored photoluminescent composites. Here we describe a single active layer prototype display that utilizes these materials

Increasing prevalence despite decreasing incidence of ischeamic heart disease and myocardial infarction

DEFF Research Database (Denmark)

Koch, Mette Bjerrum; Davidsen, Michael; Andersen, Lisbeth V.

2015-01-01

of these changes on the prevalence of IHD is not known. METHODS AND RESULTS: Changes in incidence and prevalence in 2000-2009 are presented, using nationwide data from public registers. An incident case is defined as a subject registered with a diagnosis of IHD/AMI and without a prior diagnosis for the past 20...... years (beginning in 1980). A prevalent case is defined as a subject surviving the first year after the incident diagnosis. Regarding IHD, age-standardised incidence rates declined significantly from 2000 to 2009 for both sexes (females 445 to 340/100,000, males 822 to 678/100,000), reflecting...

Low reflectance high power RF load

Science.gov (United States)

Ives, R. Lawrence; Mizuhara, Yosuke M.

2016-02-02

A load for traveling microwave energy has an absorptive volume defined by cylindrical body enclosed by a first end cap and a second end cap. The first end cap has an aperture for the passage of an input waveguide with a rotating part that is coupled to a reflective mirror. The inner surfaces of the absorptive volume consist of a resistive material or are coated with a coating which absorbs a fraction of incident RF energy, and the remainder of the RF energy reflects. The angle of the reflector and end caps is selected such that reflected RF energy dissipates an increasing percentage of the remaining RF energy at each reflection, and the reflected RF energy which returns to the rotating mirror is directed to the back surface of the rotating reflector, and is not coupled to the input waveguide. Additionally, the reflector may have a surface which generates a more uniform power distribution function axially and laterally, to increase the power handling capability of the RF load. The input waveguide may be corrugated for HE11 mode input energy.

Thin transparent film characterization by photothermal reflectance (abstract)

Science.gov (United States)

Li Voti, R.; Wright, O. B.; Matsuda, O.; Larciprete, M. C.; Sibilia, C.; Bertolotti, M.

2003-01-01

Photothermal reflectance methods have been intensively applied to the nondestructive testing of opaque thin films [D. P. Almond and P. M. Patel, Photothermal Science and Techniques (Chapman and Hall, London, 1996); C. Bento and D. P. Almond, Meas. Sci. Technol. 6, 1022 (1995); J. Opsal, A. Rosencwaig, and D. Willenborg, Appl. Opt. 22, 3169 (1983)]. The basic principle is based on thermal wave interferometry: the opaque specimen is illuminated by a laser beam, periodically chopped at the frequency f, so as to generate a plane thermal wave in the surface region. This wave propagates in the film, approaches the rear interface (film-bulk), is partially reflected back, reaches the front surface, is again partially reflected back and so on, giving rise to thermal wave interference. A consequence of this interference is that the surface temperature may be enhanced (constructive interference) or reduced (destructive interference) by simply scanning the frequency f (that is, the thermal diffusion length μ=√D/πf ), so as to observe damped oscillations as a function of f; in practice only the first oscillation may be clearly resolved and used to measure either the film thickness d or the film thermal diffusivity D, and this situation occurs when μ≈d. In general, photothermal reflectance does not measure directly the surface temperature variation, but rather a directly related signal determined by the thermo-optic coefficients and the sample geometry; for detection it is common to monitor the optical reflectivity variation of a probe beam normally incident on the sample. If the thin film is partially transparent to the probe, the theory becomes more difficult [O. Matsuda and O. B. Wright, J. Opt. Soc. Am. B (in press)] and one should consider the probe beam multiple reflections in the thin film. The probe modulation is optically inhomogeneous due to the temperature-induced changes in refractive index. Although in the past the complexity of the analysis has impeded

Acousto-optic control of internal acoustic reflection in tellurium dioxide crystal in case of strong elastic energy walkoff [Invited].

Science.gov (United States)

Voloshinov, Vitaly; Polikarpova, Nataliya; Ivanova, Polina; Khorkin, Vladimir

2018-04-01

Peculiar cases of acoustic wave propagation and reflection may be observed in strongly anisotropic acousto-optical crystals. A tellurium dioxide crystal serves as a prime example of such media, since it possesses record indexes of acoustic anisotropy. We studied one of the unusual scenarios of acoustic incidence and reflection from a free crystal-vacuum boundary in paratellurite. The directions of the acoustic waves in the (001) plane of the crystal were determined, and their basic characteristics were calculated. The carried-out acousto-optic experiment at the wavelength of light 532 nm and the acoustic frequency 73 MHz confirmed the theoretical predictions. The effects examined in the paper include the acoustic wave propagation with the record walkoff angle 74°. We also observed the incidence of the wave on the boundary at the angle exceeding 90°. Finally, we registered the close-to-back reflection of acoustic energy following the incidence. One of the stunning aspects is the distribution of energy between the incident and the back-reflected wave. The unusual features of the acoustic wave reflections pointed out in the paper are valuable for their possible applications in acousto-optic devices.

A study on reflection pattern of swells from the shoreline of peninsular India

Digital Repository Service at National Institute of Oceanography (India)

Anoop, T.R.; SanilKumar, V.; Johnson, G.

and tidal current on the reflected waves were examined. For the locations off the west coast of India, seasons have large impact on the reflection coefficient and were relatively less during the monsoon season due to the increase in incident wave energy...

Incidence of cervical dysplasia and cervical cancer in women living with HIV in Denmark

DEFF Research Database (Denmark)

Thorsteinsson, Kristina; Ladelund, Steen; Jensen-Fangel, Søren

2014-01-01

and hazard ratios (HRs) for time from inclusion to first cervical intraepithelial neoplasia (CIN)/ICC and time from first normal cervical cytology to first CIN/ICC were estimated. Sensitivity analyses were performed to include prior screening outcome, screening intensity and treatment of CIN......INTRODUCTION: Women living with HIV (WLWH) are reportedly at increased risk of invasive cervical cancer (ICC). WLWH in Denmark attend the National ICC screening program less often than women in the general population. We aimed to estimate the incidence of cervical dysplasia and ICC in WLWH...... with normal baseline cytology, incidences of CIN1+ and CIN2+ were higher in WLWH. However, incidences were comparable between WLWH and controls adherent to the National ICC screening program. CONCLUSIONS: Overall, WLWH develop more cervical disease than controls. However, incidences of CIN are comparable...

Total internal reflection tomography of small objects

International Nuclear Information System (INIS)

Chen Xudong

2008-01-01

The multiple signal classification (MUSIC) imaging method is applied to determine the locations of a collection of small anisotropic spherical scatterers in the framework of the total internal reflection tomography. Multiple scattering between scatterers is considered and the inverse scattering problem is nonlinear, which, however, is solved by the proposed fast analytical approach where no associated forward problem is iteratively evaluated. The paper also discusses the role of the polarization of incidence waves, the incidence angle, the separation of scatterers from the surface of the substrate, and the level of noise on the resolution of imaging.

On normal modes of gas sheets and discs

International Nuclear Information System (INIS)

Drury, L.O'C.

1980-01-01

A method is described for calculating the reflection and transmission coefficients characterizing normal modes of the Goldreich-Lynden-Bell gas sheet. Two families of gas discs without self-gravity for which the normal modes can be found analytically are given and used to illustrate the validity of the sheet approximation. (author)

Change in spatial coherence of light on refraction and on reflection.

Science.gov (United States)

Lahiri, Mayukh; Wolf, Emil

2013-06-01

A theory of refraction and reflection of partially coherent electromagnetic beams has been recently developed. In this paper, we apply it to study the change in spatial coherence caused by refraction and by reflection more fully. By considering a Gaussian Schell-model beam, we show that the change is, in general, dependent on the angle of incidence.

77 FR 32006 - Special Conditions: Gulfstream Model GVI Airplane; High Incidence Protection

Science.gov (United States)

2012-05-31

... Special Conditions No. 25-423-SC] Special Conditions: Gulfstream Model GVI Airplane; High Incidence... pertaining to a high incidence protection system that replaces the stall warning system during normal... the condition existing in the test or performance standard in which V SR is being used. (3) The weight...

Full-angle Negative Reflection with An Ultrathin Acoustic Gradient Metasurface: Floquet-Bloch Modes Perspective and Experimental Verification

KAUST Repository

Liu, Bingyi

2017-07-01

Metasurface with gradient phase response offers new alternative for steering the propagation of waves. Conventional Snell\\'s law has been revised by taking the contribution of local phase gradient into account. However, the requirement of momentum matching along the metasurface sets its nontrivial beam manipulation functionality within a limited-angle incidence. In this work, we theoretically and experimentally demonstrate that the acoustic gradient metasurface supports the negative reflection for full-angle incidence. The mode expansion theory is developed to help understand how the gradient metasurface tailors the incident beams, and the full-angle negative reflection occurs when the first negative order Floquet-Bloch mode dominates. The coiling-up space structures are utilized to build desired acoustic gradient metasurface and the full-angle negative reflections have been perfectly verified by experimental measurements. Our work offers the Floquet-Bloch modes perspective for qualitatively understanding the reflection behaviors of the acoustic gradient metasurface and enables a new degree of the acoustic wave manipulating.

'Incidence Of Dry Socket\\' In Benin City: Analysis Of 21 Cases ...

African Journals Online (AJOL)

Zinc oxide/Eugenol dressing was the mainstay of treatment after irrigation of the socket with normal saline. The low incidence of dry socket in this review shows that it is not a common complication of tooth extraction in our hospital. Keywords: Dry socket, incidence. Annals of Biomedical Science Vol. 2 (2) 2003: pp. 82-87 ...

Reflective and antireflective coatings for the optical chain of the ASTRI SST-2M prototype

Science.gov (United States)

Bonnoli, Giacomo; Canestrari, Rodolfo; Catalano, Osvaldo; Pareschi, Giovanni; Perri, Luca; Stringhetti, Luca

2013-09-01

ASTRI is a Flagship Project of the Italian Ministry of Education, University and Research, led by the Italian National Institute of Astrophysics, INAF. One of the main aims of the ASTRI Project is the design, construction and on-field verification of a dual mirror (2M) end-to-end prototype for the Small Size Telescope (SST) envisaged to become part of the Cherenkov Telescope Array. The ASTRI SST-2M prototype is designed according to the Schwarzschild-Couder optical scheme, and adopts a camera based on Silicon Photo Multipliers (SiPM); it will be assembled at the INAF astronomical site of Serra La Nave on mount Etna (Catania, Italy) in the second half of 2014, and will start scientific validation phase soon after. With its 4m wide primary dish, the telescope will be sensitive to multi-TeV Very High Energy (VHE) gamma rays up to 100 TeV and above, with a point spread function of ~2 arcminutes and a wide (semiaperture 4.8°) corrected field of view. The peculiarities of the optical design and of the SiPM bandpass pushed towards specifically optimized choices in terms of reflective coatings for both the primary and the secondary mirror. Fully dielectric multi-layer coatings have been developed and tested as an option for the primary mirror, aiming to filter out the large Night Sky Background contamination at wavelengths λ>~700 nm. On the other hand, for the large monolithic secondary mirror a simpler design with quartz-overcoated aluminium has been optimized for incidences far from normality. The conformation of the ASTRI camera in turn pushed towards the design of a reimaging system based on thin pyramidal light guides, that could be optionally integrated in the focal surface, aiming to increase the fill factor. An anti-reflective coating optimized for a wide range of incident angles faraway from normality was specifically developed to enhance the UV-optical transparency of these elements. The issues, strategy, simulations and experimental results are thoroughly

Modified polarimetric bidirectional reflectance distribution function with diffuse scattering: surface parameter estimation

Science.gov (United States)

Zhan, Hanyu; Voelz, David G.

2016-12-01

The polarimetric bidirectional reflectance distribution function (pBRDF) describes the relationships between incident and scattered Stokes parameters, but the familiar surface-only microfacet pBRDF cannot capture diffuse scattering contributions and depolarization phenomena. We propose a modified pBRDF model with a diffuse scattering component developed from the Kubelka-Munk and Le Hors et al. theories, and apply it in the development of a method to jointly estimate refractive index, slope variance, and diffuse scattering parameters from a series of Stokes parameter measurements of a surface. An application of the model and estimation approach to experimental data published by Priest and Meier shows improved correspondence with measurements of normalized Mueller matrix elements. By converting the Stokes/Mueller calculus formulation of the model to a degree of polarization (DOP) description, the estimation results of the parameters from measured DOP values are found to be consistent with a previous DOP model and results.

Femtosecond tracking of carrier relaxation in germanium with extreme ultraviolet transient reflectivity

Science.gov (United States)

Kaplan, Christopher J.; Kraus, Peter M.; Ross, Andrew D.; Zürch, Michael; Cushing, Scott K.; Jager, Marieke F.; Chang, Hung-Tzu; Gullikson, Eric M.; Neumark, Daniel M.; Leone, Stephen R.

2018-05-01

Extreme ultraviolet (XUV) transient reflectivity around the germanium M4 ,5 edge (3 d core-level to valence transition) at 30 eV is advanced to obtain the transient dielectric function of crystalline germanium [100] on femtosecond to picosecond time scales following photoexcitation by broadband visible-to-infrared (VIS/NIR) pulses. By fitting the transient dielectric function, carrier-phonon induced relaxations are extracted for the excited carrier distribution. The measurements reveal a hot electron relaxation rate of 3.2 ±0.2 ps attributed to the X -L intervalley scattering and a hot hole relaxation rate of 600 ±300 fs ascribed to intravalley scattering within the heavy hole (HH) band, both in good agreement with previous work. An overall energy shift of the XUV dielectric function is assigned to a thermally induced band gap shrinkage by formation of acoustic phonons, which is observed to be on a timescale of 4-5 ps, in agreement with previously measured optical phonon lifetimes. The results reveal that the transient reflectivity signal at an angle of 66∘ with respect to the surface normal is dominated by changes to the real part of the dielectric function, due to the near critical angle of incidence of the experiment (66∘-70∘) for the range of XUV energies used. This work provides a methodology for interpreting XUV transient reflectivity near core-level transitions, and it demonstrates the power of the XUV spectral region for measuring ultrafast excitation dynamics in solids.

Usefulness of normal saline for sealing the needle track after CT-guided lung biopsy

International Nuclear Information System (INIS)

Li, Y.; Du, Y.; Luo, T.Y.; Yang, H.F.; Yu, J.H.; Xu, X.X.; Zheng, H.J.; Li, B.

2015-01-01

Aim: To determine whether the use of normal saline for sealing the needle track can reduce the incidence of pneumothorax and chest tube placement after computed tomography (CT)-guided lung biopsy. Materials and methods: A prospective, randomised, controlled trial enrolling 322 patients was conducted. All patients were randomly assigned to one of two groups: those in whom the needle track was not sealed with normal saline (n=161, Group A) and those who did receive normal saline (n=161, Group B). CT-guided biopsy was performed with coaxial technique. Normal saline, which ranged from 1–3 ml, was injected while the trocar needle was being withdrawn. Patient characteristics, lesion, and procedure variables were analysed as potential risk variables for occurrence of pneumothorax and chest tube placement. Results: The incidence of pneumothorax was 26.1% in Group A and 6.2% in Group B (p<0.001). Nine patients in Group A and one patient in Group B required chest tube placement (p=0.010). Using multiple logistic regression analysis, smaller lesion size, greater needle–pleural angle, longer lesion–pleural distance, presence of emphysema, and no sealing the needle track with normal saline were significantly associated with an increased risk of pneumothorax, and that the latter three factors were also associated with an increased risk of pneumothorax requiring chest tube placement. Conlusion: Normal saline for sealing the needle track significantly reduces the incidence of pneumothorax and prevents subsequent chest tube placement after CT-guided lung biopsy. - Highlights: • Normal saline is an effective sealant for use in lung biopsy. • This technique reduced the incidence of pneumothorax and chest tube placement. • This technique should be recommended for CT-guided lung biopsy.

Systematic Review and Meta-Analysis on Incidence of Altered Sensation of Mandibular Implant Surgery

Science.gov (United States)

Lin, Chia-Shu; Wu, Shih-Yun; Huang, Hsin-Yi; Lai, Yu-Lin

2016-01-01

Altered sensation (including paresthesia, dysesthesia and hypoesthesia) after mandibular implant surgery may indicate transient or permanent injury of the inferior alveolar nerve and the mental branch, and considerably lower patients’ satisfaction about the therapy. Previous studies have shown a great degree of variability on the incidence of altered sensation. We here reported the incidence of altered sensation after mandibular implant surgery based on a meta-analysis of 26 articles published between 1990.1.1 and 2016.1.1. Study quality and risk of bias was assessed and the studies with a lower score were excluded in the meta-analysis. Data synthesis was performed using the logistic-normal random-effect model. The meta-analyses revealed that the short-term (10 days after implant placement) and long-term (1 year after implant placement) incidence was 13% (95% CI, 6%-25%) and 3% (95% CI, 1%-7%), respectively. (2) For the patients who initially reported altered sensation, 80% (95% CI, 52%-94%) of them would return to normal sensation within 6 months after surgery, and 91% (95% CI, 78%-96%) of them would return to normal sensation one year after surgery. We concluded that dentist-patient communication about the risk of altered sensation is critical to treatment planning, since the short-term incidence of altered sensation is substantial (13%). When a patient reports altered sensation, regular assessment for 6 months would help tracing the changes of symptoms. In terms of long-term follow-up (1 year after surgery), the incidence is much lower (3%) and most patients (91%) would return to normal sensation. PMID:27100832

Systematic Review and Meta-Analysis on Incidence of Altered Sensation of Mandibular Implant Surgery.

Directory of Open Access Journals (Sweden)

Chia-Shu Lin

Full Text Available Altered sensation (including paresthesia, dysesthesia and hypoesthesia after mandibular implant surgery may indicate transient or permanent injury of the inferior alveolar nerve and the mental branch, and considerably lower patients' satisfaction about the therapy. Previous studies have shown a great degree of variability on the incidence of altered sensation. We here reported the incidence of altered sensation after mandibular implant surgery based on a meta-analysis of 26 articles published between 1990.1.1 and 2016.1.1. Study quality and risk of bias was assessed and the studies with a lower score were excluded in the meta-analysis. Data synthesis was performed using the logistic-normal random-effect model. The meta-analyses revealed that the short-term (10 days after implant placement and long-term (1 year after implant placement incidence was 13% (95% CI, 6%-25% and 3% (95% CI, 1%-7%, respectively. (2 For the patients who initially reported altered sensation, 80% (95% CI, 52%-94% of them would return to normal sensation within 6 months after surgery, and 91% (95% CI, 78%-96% of them would return to normal sensation one year after surgery. We concluded that dentist-patient communication about the risk of altered sensation is critical to treatment planning, since the short-term incidence of altered sensation is substantial (13%. When a patient reports altered sensation, regular assessment for 6 months would help tracing the changes of symptoms. In terms of long-term follow-up (1 year after surgery, the incidence is much lower (3% and most patients (91% would return to normal sensation.

The Effect of Non-Lambertian Surface Reflectance on Aerosol Radiative Forcing

Energy Technology Data Exchange (ETDEWEB)

Ricchiazzi, P.; O' Hirok, W.; Gautier, C.

2005-03-18

Surface reflectance is an important factor in determining the strength of aerosol radiative forcing. Previous studies of radiative forcing assumed that the reflected surface radiance is isotropic and does not depend on incident illumination angle. This Lambertian reflection model is not a very good descriptor of reflectance from real land and ocean surfaces. In this study we present computational results for the seasonal average of short and long wave aerosol radiative forcing at the top of the atmosphere and at the surface. The effect of the Lambertian assumption is found through comparison with calculations using a more detailed bi-direction reflectance distribution function (BRDF).

Optimum angle of incidence for monochromatic interference in transparent films on absorbing substrates

International Nuclear Information System (INIS)

Muller, R.H.; Sand, M.L.

1980-01-01

Angles of incidence for s- and p-polarized light have been computed and confirmed experimentally for which monochromatic interference in transparent thin films on absorbing substrates results in optimum interference fringe contrast (visibility=1). Under these angles of incidence and with polarized light, film thickness determinations which are not possible at normal incidence or with unpolarized light can be carried out by use of thin-film interference

Identifying diffraction effects in measured reflectances

OpenAIRE

Holzschuch , Nicolas; Pacanowski , Romain

2015-01-01

International audience; There are two different physical models connecting the micro-geometry of a surface and its physical reflectance properties (BRDF). The first, Cook-Torrance, assumes geometrical optics: light is reflected and masked by the micro-facets. In this model, the BRDF depends on the probability distribution of micro-facets normals. The second, Church-Takacs, assumes diffraction by the micro-geometry. In this model, the BRDF depends on the power spectral distribution of the surf...

Uniformity of the soft-x-ray emissions from gold foils irradiated by OMEGA laser beams determined by a two-mirror normal-incidence microscope with multilayer coatings

International Nuclear Information System (INIS)

Seely, John F.; Boehly, Thomas; Pien, Gregory; Bradley, David

1998-01-01

A two-mirror normal-incidence microscope with multilayer coatings was used to image the soft-x-ray emissions from planar foils irradiated by OMEGA laser beams. The bandpass of the multilayer coatings was centered at a wavelength of 48.3 Angstrom (257-eV energy) and was 0.5 Angstrom wide. Five overlapping OMEGA beams, without beam smoothing, were typically incident on the gold foils. The total energy was 1500 J, and the focused intensity was 6x10 13 Wcm -2 . The 5.8x magnified images were recorded by a gated framing camera at various times during the 3-ns laser pulse. A pinhole camera imaged the x-ray emission in the energy range of >2 keV. On a spatial scale of 10 μm, it was found that the soft-x-ray images at 257 eV were quite uniform and featureless. In contrast, the hard-x-ray images in the energy range of >2 kev were highly nonuniform with numerous features of size 150 μm. copyright 1998 Optical Society of America

Reflection and Transmission of a Focused Finite Amplitude Sound Beam Incident on a Curved Interface

Science.gov (United States)

Makin, Inder Raj Singh

Reflection and transmission of a finite amplitude focused sound beam at a weakly curved interface separating two fluid-like media are investigated. The KZK parabolic wave equation, which accounts for thermoviscous absorption, diffraction, and nonlinearity, is used to describe the high intensity focused beam. The first part of the work deals with the quasilinear analysis of a weakly nonlinear beam after its reflection and transmission from a curved interface. A Green's function approach is used to define the field integrals describing the primary and the nonlinearly generated second harmonic beam. Closed-form solutions are obtained for the primary and second harmonic beams when a Gaussian amplitude distribution at the source is assumed. The second part of the research uses a numerical frequency domain solution of the KZK equation for a fully nonlinear analysis of the reflected and transmitted fields. Both piston and Gaussian sources are considered. Harmonic components generated in the medium due to propagation of the focused beam are evaluated, and formation of shocks in the reflected and transmitted beams is investigated. A finite amplitude focused beam is observed to be modified due to reflection and transmission from a curved interface in a manner distinct from that in the case of a small signal beam. Propagation curves, beam patterns, phase plots and time waveforms for various parameters defining the source and media pairs are presented, highlighting the effect of the interface curvature on the reflected and transmitted beams. Relevance of the current work to biomedical applications of ultrasound is discussed.

Nature of Blame in Patient Safety Incident Reports: Mixed Methods Analysis of a National Database.

Science.gov (United States)

Cooper, Jennifer; Edwards, Adrian; Williams, Huw; Sheikh, Aziz; Parry, Gareth; Hibbert, Peter; Butlin, Amy; Donaldson, Liam; Carson-Stevens, Andrew

2017-09-01

A culture of blame and fear of retribution are recognized barriers to reporting patient safety incidents. The extent of blame attribution in safety incident reports, which may reflect the underlying safety culture of health care systems, is unknown. This study set out to explore the nature of blame in family practice safety incident reports. We characterized a random sample of family practice patient safety incident reports from the England and Wales National Reporting and Learning System. Reports were analyzed according to prespecified classification systems to describe the incident type, contributory factors, outcomes, and severity of harm. We developed a taxonomy of blame attribution, and we then used descriptive statistical analyses to identify the proportions of blame types and to explore associations between incident characteristics and one type of blame. Health care professionals making family practice incident reports attributed blame to a person in 45% of cases (n = 975 of 2,148; 95% CI, 43%-47%). In 36% of cases, those who reported the incidents attributed fault to another person, whereas 2% of those reporting acknowledged personal responsibility. Blame was commonly associated with incidents where a complaint was anticipated. The high frequency of blame in these safety, incident reports may reflect a health care culture that leads to blame and retribution, rather than to identifying areas for learning and improvement, and a failure to appreciate the contribution of system factors in others' behavior. Successful improvement in patient safety through the analysis of incident reports is unlikely without achieving a blame-free culture. © 2017 Annals of Family Medicine, Inc.

Reflection Patterns Generated by Condensed-Phase Oblique Detonation Interaction with a Rigid Wall

Science.gov (United States)

Short, Mark; Chiquete, Carlos; Bdzil, John; Meyer, Chad

2017-11-01

We examine numerically the wave reflection patterns generated by a detonation in a condensed phase explosive inclined obliquely but traveling parallel to a rigid wall as a function of incident angle. The problem is motivated by the characterization of detonation-material confiner interactions. We compare the reflection patterns for two detonation models, one where the reaction zone is spatially distributed, and the other where the reaction is instantaneous (a Chapman-Jouguet detonation). For the Chapman-Jouguet model, we compare the results of the computations with an asymptotic study recently conducted by Bdzil and Short for small detonation incident angles. We show that the ability of a spatially distributed reaction energy release to turn flow streamlines has a significant impact on the nature of the observed reflection patterns. The computational approach uses a shock-fit methodology.

The generalized vectorial laws of reflection and refraction

International Nuclear Information System (INIS)

Bhattacharjee, Pramode Ranjan

2005-01-01

This paper discloses two important discoveries. These are: (i) discovery of ambiguity in the well-established laws of reflection and refraction of light which have been in regular use for many years, and (ii) discovery of generalized vectorial laws of reflection and refraction of light. The existing definitions of angle of incidence, angle of reflection and angle of refraction are considered first. Each of these definitions is found to be ambiguous, not in compliance with the fundamental definition of angle in geometry. Two typical questions (one in the case of reflection and the other for refraction) have been addressed, which cannot be dealt with by using the existing laws of reflection and refraction of light. Thus, the existing laws of reflection and refraction of light seem to be ambiguous in respect of generality and their validity in a broad sense is questionable. With a view to removing the ambiguities, proper definitions of the above three angles are given first and then the statement of the generalized vectorial law of reflection (as well as that of refraction) has been offered

Modification of radiation-induced murine thymic lymphoma incidence by curcumin

International Nuclear Information System (INIS)

Dange, P.S.; Yadav, H.D.; Kumar, Vimalesh; Bhilwade, H.N.; Pandey, B.N.; Sarma, H.D.

2017-01-01

Curcumin is a known antioxidant, preventing radiation damage including carcinogenesis. However, concentration and feeding schedule of curcumin in modification of radiation induced thymic lymphoma incidence in vivo model has not been studied. We report here modification of incidence of γ-radiation-induced thymic lymphoma in mice fed with different doses of curcumin (0.05 to 1 %) in diet. Results: Female Swiss mice (6-8 weeks) fed with normal diet and exposed to 3 Gy whole body "6"0Co γ-irradiation (WBI) showed 85 % incidence of thymic lymphoma (TL) at 120 days post-irradiation. A concentration of 1 % curcumin was found the most effective in TL incidence prevention than other fed concentrations. The TL incidence was remarkably reduced when curcumin was fed to the mice before than after the radiation exposure. These results suggest modification of TL incidence by curcumin in irradiated mice involving DNA damage and apoptotic death mechanisms

Fragmentation mechanism reflecting the cluster structure of {sup 19}B

Energy Technology Data Exchange (ETDEWEB)

Takemoto, H.; Horiuchi, H. [Kyoto Univ., Dept. of Physics, Kyoto (Japan); Ono, A.

1999-08-01

Clustering structure of neutron dripline nucleus {sup 19}B which was predicted theoritically is investigated by studying the fragmentation reaction of {sup 19}B. We compare {sup 19}B fragmentation with {sup 13}B fragmentation in {sup 19}B + {sup 14}N and {sup 13}B + {sup 14}N reactions by using antisymmetrized molecular dynamics, where {sup 13}B has no clustering feature in its structure. We find that the cluster structure of the {sup 19}B nucleus is reflected in its fragmentation as the simultaneous production of He and Li isotopes. Furthermore we investigate the dependence of the cluster decay of {sup 19}B on the incident energy, and find that the cluster structure of {sup 19}B in its ground state is more reflected in lower incident-energy reactions. (author)

Reflection of slow hydrogen and helium ions from solid surfaces

International Nuclear Information System (INIS)

Akkerman, A.F.

1978-01-01

Some characteristics of the proton and helium ion flux (E < 10 keV), reflected from solid surfaces are presented. A 'condensed walk' scheme, previously used for electron transport calculations, was adapted. Results obtained either by the scheme or by a more detailed 'consequent' scheme agreed closely. The presented data permit calculations of the mean energy of reflected particles and other values for various energy and angular distributions of incident particles. (author)

Laser reflection spot as a pattern in a diamond coating – a microscopic study

Directory of Open Access Journals (Sweden)

GORDANA S. RISTIĆ

2009-07-01

Full Text Available Diamond coatings were deposited by the synchronous and coupled action of a hot filament CVD method and a pulsed CO2 laser in spectro-absorbing and spectro-non-absorbing diamond precursor atmospheres. The obtained coatings were structured/patterned, i.e., they were comprised of uncovered, bare locations. An extra effect observed only in the spectro-active diamond precursor atmosphere was the creation of another laser spot in the coating – a reflection spot. In order to establish the practical usability of the latter one, extensive microscopic investigations were performed with consideration of the morphology changes in the spot of the direct laser beam. Normal incidence SEM images of this spot showed a smooth surface, without any pulse radiation damage. AFM imaging revealed the actual surface condition and gave precise data on the surface characteristics.

The incidence of spondylolysis and spondylolisthesis in children with osteogenesis imperfecta.

Science.gov (United States)

Hatz, Daniel; Esposito, Paul W; Schroeder, Bruce; Burke, Bridget; Lutz, Richard; Hasley, Brian P

2011-09-01

Spondylolysis and spondylolisthesis are common abnormalities of the lumbar spine. The incidence of these diagnoses is recognized in the healthy population. However, their incidence in osteogenesis imperfecta (OI) patients is less well defined. This is a retrospective radiographic review of patients treated in the OI clinic from a single institution. Lateral radiographs were reviewed on all available patients to assess the incidence of spondylolysis and spondylolisthesis in this patient population. The morphology of the pedicle and pars interarticularis was also evaluated to identify any abnormalities or dysplasia of these structures. One hundred ten of the 139 patients treated in the OI clinic met the inclusion criteria for this study. Of these patients, 79% (87 of 110) were ambulatory. The overall incidence of spondylolysis in this pediatric OI population was found to be 8.2% (9 of 110) at an average age of 7.5 years. The incidence of spondylolisthesis was 10.9% (12 of 110) at an average age of 6.5 years with 75% (3 of 12) being isthmic type and 25% (3 of 12) dysplastic. The combined incidence of spondylolysis and spondylolisthesis was 19.2%. Incidentally, the pedicle length was noted to be elongated in 40.0% (44 of 110) of this OI population. This study found that the incidence of spondylolysis in a group of children with OI was much higher than in the normal pediatric population, which has been reported to be 2.6% to 4.0%. This incidence was also found to be higher than previously reported incidence of spondylolysis in OI patients (5.3%). The incidence of spondylolisthesis was also found to be much higher than that of the normal pediatric population (4.2%). It is important to recognize this higher incidence of these abnormalities and to anticipate future associated symptoms and potential worsening listhesis that can clinically affect the lifestyles of these children and potentially require surgical treatment. The clinical significance of these findings will

A functional equation for the specular reflection of rays.

Science.gov (United States)

Le Bot, A

2002-10-01

This paper aims to generalize the "radiosity method" when applied to specular reflection. Within the field of thermics, the radiosity method is also called the "standard procedure." The integral equation for incident energy, which is usually derived for diffuse reflection, is replaced by a more appropriate functional equation. The latter is used to solve some specific problems and it is shown that all the classical features of specular reflection, for example, the existence of image sources, are embodied within this equation. This equation can be solved with the ray-tracing technique, despite the implemented mathematics being quite different. Several interesting features of the energy field are presented.

Long range heliostat target using array of normal incidence pyranometers to evaluate a beam of solar radiation

Science.gov (United States)

Ghanbari, Cheryl M; Ho, Clifford K; Kolb, Gregory J

2014-03-04

Various technologies described herein pertain to evaluating a beam reflected by a heliostat. A portable target that has an array of sensors mounted thereupon is configured to capture the beam reflected by the heliostat. The sensors in the array output measured values indicative of a characteristic of the beam reflected by the heliostat. Moreover, a computing device can generate and output data corresponding to the beam reflected by the heliostat based on the measured values indicative of the characteristic of the beam received from the sensors in the array.

Tantalum films with well-controlled roughness grown by oblique incidence deposition

Science.gov (United States)

Rechendorff, K.; Hovgaard, M. B.; Chevallier, J.; Foss, M.; Besenbacher, F.

2005-08-01

We have investigated how tantalum films with well-controlled surface roughness can be grown by e-gun evaporation with oblique angle of incidence between the evaporation flux and the surface normal. Due to a more pronounced shadowing effect the root-mean-square roughness increases from about 2 to 33 nm as grazing incidence is approached. The exponent, characterizing the scaling of the root-mean-square roughness with length scale (α), varies from 0.75 to 0.93, and a clear correlation is found between the angle of incidence and root-mean-square roughness.

A Monte Carlo reflectance model for soil surfaces with three-dimensional structure

Science.gov (United States)

Cooper, K. D.; Smith, J. A.

1985-01-01

A Monte Carlo soil reflectance model has been developed to study the effect of macroscopic surface irregularities larger than the wavelength of incident flux. The model treats incoherent multiple scattering from Lambertian facets distributed on a periodic surface. Resulting bidirectional reflectance distribution functions are non-Lambertian and compare well with experimental trends reported in the literature. Examples showing the coupling of the Monte Carlo soil model to an adding bidirectional canopy of reflectance model are also given.

Computer simulation and data compilation of sputtering yield by hydrogen isotopes ({sup 1}H{sup +}, {sup 2}D{sup +}, {sup 3}T{sup +}) and helium ({sup 4}He{sup +}) ion impact from monatomic solids at normal incidence

Energy Technology Data Exchange (ETDEWEB)

Yamamura, Yasunori; Sakaoka, Kazuho; Tawara, Hiro

1995-10-01

The ion-induced sputtering yields from monatomic solids at normal incidence are presented graphically for light-ion ({sup 1}H{sup +}, {sup 2}D{sup +}, {sup 3}T{sup +}, {sup 4}He{sup +}) bombardment on various target materials as a function of the incident ion energy. To supplement the experimental data, the sputtering yields are calculated by the Monte Carlo simulation code ACAT for all possible light ion-target combinations. Each graph shows the available experimental and ACAT data points, together with the sputtering yield calculated by the Yamamura and Tawara empirical formula. (author).

Development of an ultrasonic shear reflection technique to monitor the crystallization of cocoa butter.

Science.gov (United States)

Rigolle, Annelien; Foubert, Imogen; Hettler, Jan; Verboven, Erik; Demuynck, Ruth; Van Den Abeele, Koen

2015-09-01

The quasi-isothermal crystallization process of cocoa butter was monitored by an ultrasonic shear reflection technique utilizing a custom-built experimental set-up in a temperature controlled environment. To facilitate the interpretation of the measurement results, the propagation of shear waves was first theoretically studied in different configurations of gas, liquid or solid layers with varying thickness for the case of normal incidence, yielding theoretical equations of the shear wave reflection coefficient (swRC) for different layering conditions. The typical experimentally observed pattern of the swRC during quasi-isothermal cocoa butter crystallization was subsequently linked to the theoretical equations. The remarkable oscillatory damped response in the swRC as function of the crystallization time could be explained by constructive and destructive interference of a first reflection at the boundary between a plexiglass delay line and the crystallized cocoa butter and a second reflection occurring at the interface between crystallized and liquid substance. This hypothesis was supported by the excitation frequency dependence of the oscillations. The quality of the fit of the theoretical model to the experimental results was very good and also the reproducibility between different independent measurements was acceptable. Finally, measurements at different temperatures (18°C and 20°C) suggested that the technique was able to detect differences in crystallization behavior, as measurements at 18°C displayed faster oscillations compared to measurements at 20°C. Moreover, this was also confirmed by the theoretical model, as a higher value of the crystallization rate parameter K, exhibited more rapid oscillations. Copyright © 2015 Elsevier Ltd. All rights reserved.

Normalizing Catastrophe: Sustainability and Scientism

Science.gov (United States)

Bonnett, Michael

2013-01-01

Making an adequate response to our deteriorating environmental situation is a matter of ever increasing urgency. It is argued that a central obstacle to achieving this is the way that scientism has become normalized in our thinking about environmental issues. This is taken to reflect on an underlying "metaphysics of mastery" that vitiates proper…

Evolution of the ischio-iliac lordosis during natural growth and its relation with the pelvic incidence.

Science.gov (United States)

Schlösser, Tom P C; Janssen, Michiel M A; Vrtovec, Tomaž; Pernuš, Franjo; Oner, F Cumhur; Viergever, Max A; Vincken, Koen L; Castelein, René M

2014-07-01

Human fully upright ambulation, with fully extended hips and knees, and the body's center of gravity directly above the hips, is unique in nature, and distinguishes humans from all other mammalians. This bipedalism is made possible by the development of a lordosis between the ischium and ilium; it allows to ambulate in this unique bipedal manner, without sacrificing forceful extension of the legs. This configuration in space introduces unique biomechanical forces with relevance for a number of spinal conditions. The aim of this study was to quantify the development of this lordosis between ischium and ilium in the normal growing and adult spine and to evaluate its correlation with the well-known clinical parameter, pelvic incidence. Consecutive series of three-dimensional computed tomography scans of the abdomen of 189 children and 310 adults without spino-pelvic pathologies were used. Scan indications were trauma screening or acute abdominal pathology. Using previously validated image processing techniques, femoral heads, center of the sacral endplate and the axes of the ischial bones were semi-automatically identified. A true sagittal view of the pelvis was automatically reconstructed, on which ischio-iliac angulation and pelvic incidence were calculated. The ischio-iliac angle was defined as the angle between the axes of the ischial bones and the line from the midpoint of the sacral endplate to the center of the femoral heads. A wide natural variation of the ischio-iliac angle (3°-46°) and pelvic incidence (14°-77°) was observed. Pearson's analysis demonstrated a significant correlation between the ischio-iliac angle and pelvic incidence (r = 0.558, P lordosis is unique in nature, is in harmonious continuity with the highly individual lumbar lordosis and defines the way the human spine is biomechanically loaded. The practical parameter that reflects this is the pelvic incidence; both values increase during growth and remain stable in adulthood.

Reflective self-awareness and conscious states

DEFF Research Database (Denmark)

Kjaer, Troels W; Nowak, Markus; Lou, Hans C

2002-01-01

A recent meta-analysis has shown precuneus, angular gyri, anterior cingulate gyri, and adjacent structures to be highly metabolically active in support of resting consciousness. We hypothesize that these regions constitute a functional network of reflective self-awareness thought to be a core...... function of consciousness. Seven normal volunteers were asked to think intensely on how they would describe the personality traits and physical appearance of themselves and a neutral reference person known to all the subjects (the Danish Queen). During each of the four conditions cerebral blood flow...... during reflective self-awareness. The commonality between the neural networks of the resting conscious state and self-awareness reflects the phenomenological concept of a fundamental contribution of reflective self-awareness to the contents and coherence of the conscious state....

Prácticas para estimular el parto normal Practices to stimulate normal childbirth

Directory of Open Access Journals (Sweden)

Flora Maria Barbosa da Silva

2011-09-01

Full Text Available Este artículo lleva a una reflexión sobre las prácticas del estímulo al parto normal, con la fundamentación teórica de cada una de ellas. Las prácticas incluidas en este estudio fueron el ayuno, enemas, spray y baños de inmersión, caminatas, movimientos pélvicos y masaje. En un contexto de revalorización del parto normal, ofrecer a la mujer durante el parto opciones de comodidad basadas en evidencias puede ser una forma de preservar el curso fisiológico del parto.This article leads to a reflection about the practices of encouraging normal childbirth, with the theoretical foundation for each one of them. The practices included in this study were fasting, enema, shower and immersion baths, walking, pelvic movements and massage. In a context of revaluation of normal birth, providing evidence-based comfort options for women during childbirth can be a way to preserve the physiological course of labour.

Giant enhancement of reflectance due to the interplay between surface confined wave modes and nonlinear gain in dielectric media.

Science.gov (United States)

Kim, Sangbum; Kim, Kihong

2017-12-11

We study theoretically the interplay between the surface confined wave modes and the linear and nonlinear gain of the dielectric layer in the Otto configuration. The surface confined wave modes, such as surface plasmons or waveguide modes, are excited in the dielectric-metal bilayer by obliquely incident p waves. In the purely linear case, we find that the interplay between linear gain and surface confined wave modes can generate a large reflectance peak with its value much greater than 1. As the linear gain parameter increases, the peak appears at smaller incident angles, and the associated modes also change from surface plasmons to waveguide modes. When the nonlinear gain is turned on, the reflectance shows very strong multistability near the incident angles associated with surface confined wave modes. As the nonlinear gain parameter is varied, the reflectance curve undergoes complicated topological changes and sometimes displays separated closed curves. When the nonlinear gain parameter takes an optimally small value, a giant amplification of the reflectance by three orders of magnitude occurs near the incident angle associated with a waveguide mode. We also find that there exists a range of the incident angle where the wave is dissipated rather than amplified even in the presence of gain. We suggest that this can provide the basis for a possible new technology for thermal control in the subwavelength scale.

Grazing incidence diffraction : A review

Energy Technology Data Exchange (ETDEWEB)

Gilles, B [LTPCM, ENSEEG. St. Martin d` Heres. (France)

1996-09-01

Different Grazing Incidence Diffraction (GID) methods for the analysis of thin films and multilayer structures are reviewed in three sections: the reflectivity is developed in the first one, which includes the non-specular diffuse scattering. The second one is devoted to the extremely asymmetric Bragg diffraction and the third one to the in-plane Bragg diffraction. Analytical formulations of the scattered intensities are developed for each geometry, in the framework of the kinetical analysis as well as the dynamical theory. Experimental examples are given to illustrate the quantitative possibility of the GID techniques.

Surface damage on 6H–SiC by highly-charged Xeq+ ions irradiation

International Nuclear Information System (INIS)

Zhang, L.Q.; Zhang, C.H.; Han, L.H.; Xu, C.L.; Li, J.J.; Yang, Y.T.; Song, Y.; Gou, J.; Li, J.Y.; Ma, Y.Z.

2014-01-01

Surface damage on 6H–SiC irradiated by highly-charged Xe q+ (q = 18, 26) ions to different fluences in two geometries was studied by means of AFM, Raman scattering spectroscopy and FTIR spectrometry. The FTIR spectra analysis shows that for Xe 26+ ions irradiation at normal incidence, a deep reflection dip appears at about 930 cm −1 . Moreover, the reflectance on top of reststrahlen band decreases as the ion fluence increases, and the reflectance at tilted incidence is larger than that at normal incidence. The Raman scattering spectra reveal that for Xe 26+ ions at normal incidence, surface reconstruction occurs and amorphous stoichiometric SiC and Si–Si and C–C bonds are generated and original Si–C vibrational mode disappears. And the intensity of scattering peaks decreases with increasing dose. The AFM measurement shows that the surface swells after irradiation. With increasing ion fluence, the step height between the irradiated and the unirradiated region increases for Xe 18+ ions irradiation; while for Xe 26+ ions irradiation, the step height first increases and then decreases with increasing ion fluence. Moreover, the step height at normal incidence is higher than that at tilted incidence by the irradiation with Xe 18+ to the same ion fluence. A good agreement between the results from the three methods is found

Quantum arrival times and operator normalization

International Nuclear Information System (INIS)

Hegerfeldt, Gerhard C.; Seidel, Dirk; Gonzalo Muga, J.

2003-01-01

A recent approach to arrival times used the fluorescence of an atom entering a laser illuminated region, and the resulting arrival-time distribution was close to the axiomatic distribution of Kijowski, but not exactly equal, neither in limiting cases nor after compensation of reflection losses by normalization on the level of expectation values. In this paper we employ a normalization on the level of operators, recently proposed in a slightly different context. We show that in this case the axiomatic arrival-time distribution of Kijowski is recovered as a limiting case. In addition, it is shown that Allcock's complex potential model is also a limit of the physically motivated fluorescence approach and connected to Kijowski's distribution through operator normalization

Guide on reflectivity data analysis

International Nuclear Information System (INIS)

Lee, Jeong Soo; Ku, Ja Seung; Seong, Baek Seok; Lee, Chang Hee; Hong, Kwang Pyo; Choi, Byung Hoon

2004-09-01

This report contains reduction and fitting process of neutron reflectivity data by REFLRED and REFLFIT in NIST. Because the detail of data reduction like BKG, footprint and data normalization was described, it will be useful to the user who has no experience in this field. Also, reflectivity and BKG of d-PS thin film were measured by HANARO neutron reflectometer. From these, the structure of d-PS thin film was analyzed with REFLRED and REFLFIT. Because the structure of thin film such as thickness, roughness and SLD was attained in the work, the possibility of data analysis with REFLRED and REFLFIT was certified

[Analysis of influencing factors of snow hyperspectral polarized reflections].

Science.gov (United States)

Sun, Zhong-Qiu; Zhao, Yun-Sheng; Yan, Guo-Qian; Ning, Yan-Ling; Zhong, Gui-Xin

2010-02-01

Due to the need of snow monitoring and the impact of the global change on the snow, on the basis of the traditional research on snow, starting from the perspective of multi-angle polarized reflectance, we analyzed the influencing factors of snow from the incidence zenith angles, the detection zenith angles, the detection azimuth angles, polarized angles, the density of snow, the degree of pollution, and the background of the undersurface. It was found that these factors affected the spectral reflectance values of the snow, and the effect of some factors on the polarization hyperspectral reflectance observation is more evident than in the vertical observation. Among these influencing factors, the pollution of snow leads to an obvious change in the snow reflectance spectrum curve, while other factors have little effect on the shape of the snow reflectance spectrum curve and mainly impact the reflection ratio of the snow. Snow reflectance polarization information has not only important theoretical significance, but also wide application prospect, and provides new ideas and methods for the quantitative research on snow using the remote sensing technology.

Atrophic Gastritis and the Risk of Incident Colorectal Cancer

Science.gov (United States)

Laiyemo, Adeyinka O.; Kamangar, Farin; Marcus, Pamela M.; Taylor, Philip R.; Virtamo, Jarmo; Albanes, Demetrius; Stolzenberg-Solomon, Rachael Z.

2012-01-01

Objective Previous studies evaluating whether risk factors for gastric cancer are also associated with colorectal cancer (CRC) have shown inconsistent results. We prospectively examined the association of atrophic gastritis, a pre-malignant condition for gastric cancer and long-term sequelae common to many exposure factors, and the risk of incident CRC. Methods A total of 20,928 Finnish male smokers, aged 50–69, who were participants in the Alpha-Tocopherol, Beta-Carotene Cancer Prevention Study (ATBC) had serum pepsinogen I (SPGI) levels measured. Participants with low SPGI levels (gastritis was histologically confirmed in 1,006 (95.0%) participants. We used Cox proportional hazards regression to evaluate the risk of incident CRC. Results During a mean follow-up of 11.3 years (236,258 person-years), 425 incident CRC were diagnosed. The incidence rates were 1.82, 1.48, and 1.82 per 1,000 person-years of follow-up for participants with normal SPGI (≥25 µg/l), low SPGI, and histologically-confirmed atrophic gastritis, respectively. Compared to subjects with normal SPGI, there was no increased risk of CRC among subjects with low SPGI (Adjusted Hazard Ratio (HR) = 0.71; 95%CI: 0.47–1.05) and among those with histologically-confirmed atrophic gastritis (Adjusted HR = 0.86; 95%CI: 0.55–1.34). Conclusions Atrophic gastritis is not associated with an increased risk of colorectal cancer among male smokers. PMID:19838812

Incidents/accidents classification and reporting in Statoil.

Science.gov (United States)

Berentsen, Rune; Holmboe, Rolf H

2004-07-26

Based on requirements in the new petroleum regulations from Norwegian Petroleum Directorate (NPD) and the realisation of a need to improve and rationalise the routines for reporting and follow up of incidents, Statoil Exploration & Production Norway (Statoil E&P Norway) has formulated a new strategy and process for handling of incidents/accidents. The following past experiences serve as basis for the changes made to incident reporting in Statoil E&P Norway; too much resources were spent on a comprehensive handling and analysis of a vast amount of incidents with less importance for the safety level, taking the focus away from the more severe and important issues at hand, the assessment of "Risk Factor", i.e. the combination of recurrence frequency and consequence, was difficult to use. The high degree of subjectivity involved in the determination of the "Risk Factor" (in particular the estimation of the recurrence frequency) resulted in poor data quality and lack of consistency in the data material. The new system for categorisation and handling of undesirable incidents was established in January 2002. The intention was to get a higher degree of focus on serious incidents (injuries, damages, loss and near misses), with a thorough handling and follow-up. This is reflected throughout the handling of the serious incidents, all the way from immediate notification of the incident, through investigation and follow-up of corrective and preventive actions. Simultaneously, it was also an objective to rationalise/simplify the handling of less serious incidents. These incidents are, however, subjected to analyses twice a year in order to utilize the learning opportunity that they also provide. A year after the introduction of this new system for categorisation and follow-up of undesirable incidents, Statoil's experiences are predominantly good; the intention to get a higher degree of focus on serious incidents (injuries, damages, loss and near misses), has been met, the data

Reflection and Transmission of P-Waves in an Intermediate Layer Lying Between Two Semi-infinite Media

Science.gov (United States)

Singh, Pooja; Chattopadhyay, Amares; Srivastava, Akanksha; Singh, Abhishek Kumar

2018-05-01

With a motivation to gain physical insight of reflection as well as transmission phenomena in frozen (river/ocean) situation for example in Antarctica and other coldest place on Earth, the present article undertakes the analysis of reflection and transmission of a plane wave at the interfaces of layered structured comprised of a water layer of finite thickness sandwiched between an upper half-space constituted of ice and a lower isotropic elastic half-space, which may be useful in geophysical exploration in such conditions. A closed form expression of reflection/transmission coefficients of reflected and transmitted waves has been derived in terms of angles of incidence, propagation vector, displacement vector and elastic constants of the media. Expressions corresponding to the energy partition of various reflected and transmitted waves have also been established analytically. It has been remarkably shown that the law of conservation of energy holds good in the entire reflection and transmission phenomena for different angles of incidence. A numerical examples were performed so to graphically portray the analytical findings. Further the deduced results are validated with the pre-established classical results.

Mirror and Bragg reflections of neutrons at a nuclear resonance: [Final technical report

International Nuclear Information System (INIS)

Batigun, C.M.; Brugger, R.M.

1987-01-01

These experiments have observed the mirror reflection and Bragg diffraction of neutrons at the energy of a low lying nuclear resonance of 115 In. The reflector was a mirror of In metal with the resonance at 1.457 eV. The mirror reflection for different angles of incidence has been measured and sets of data showing the relative reflectivities have been obtained. For the Bragg diffraction, the crystal was a wafer of InP and several examples of Bragg reflections near 1.455 eV were measured. 4 refs., 12 figs

Effect of year of birth on the breast cancer age-incidence curve in Iceland

Energy Technology Data Exchange (ETDEWEB)

Bjarnason, O [Univ. of Iceland, Reykjavik; Day, N; Snaedal, G; Tulinius, H

1974-01-01

Among different populations, the shape of the age-incidence curve for breast cancer is strongly related to the overall incidence of breast cancer in the respective population. Data are available from Iceland for the period 1911--1972. These data show that breast cancer has increased very markedly in Iceland during this period, and that as the overall incidence has risen, so the age-incidence curve has changed in shape, the relation between the shape and the overall incidence being the same as that now observed in other countries. The change in shape is shown to be explicable entirely as a cohort phenomenon, each decade of birth cohort having an age-incidence curve of similar shape, but with different overall incidence. Data from some other regions of the world indicate that many of the present differences in the shape of the age-incidence curve may be the reflection of cohort phenomena.

Reflections about the mathematics teachers' formation

Directory of Open Access Journals (Sweden)

Maria José de Freitas Mendes

2010-06-01

Full Text Available This paper brings some reflections about the formation of the math teacher that made part of my marsters paper and that aimed to investigate the process of formation of the math teacher. The focus of this study incided at the contributions of teaching practice in the teacher's formation above the new paradigms of formation, as a professional development and as a reflexive teacher. These reflections, from the learning and teaching process and from the meaning of form a teacher analyse the crisis and the restructuration of the teacher's formation and conclude being necessary that in the graduation courses there's a character more practice to the pedagogical formation, making possible for the future teacher to develop attitudes of autonomy, reflexion and investigation

Survey of incidents in West German nuclear power plants in the last quarter of the year 1988

International Nuclear Information System (INIS)

1989-01-01

There were 79 incidents reported. Six incidents belong to reporting category E (immediate notification), the remaining 73 incidents belong to reporting category N (normal notification). The survey covers all incidents reported to GRS until the 15th of February 1989 and also includes incidents that happened before the last quarter of 1988 but were recorded later. There was no release of radioactivity involved in the incidents, and there are no effects on man or the environment reported. (orig./HP) [de

NONLINEAR OPTICAL PHENOMENA: Self-reflection effect in semiconductors in a two-pulse regime

Science.gov (United States)

Khadzhi, P. I.; Nad'kin, L. Yu

2004-12-01

Peculiarities of reflection at the end face of a semi-infinite semiconductor in a two-pulse regime are studied. The reflection functions behave in a complex and ambiguous manner governed by the amplitudes of the fields of incident pulses. The possibility of a complete bleaching of the medium for the field in the M-band is predicted.

Bandgap characteristics of 2D plasma photonic crystal with oblique incidence: TM case

International Nuclear Information System (INIS)

Xie Ying-Tao; Yang Li-Xia

2011-01-01

A novel periodic boundary condition (PBC), that is the constant transverse wavenumber (CTW) method, is introduced to solve the time delay in the transverse plane with oblique incidence. Based on the novel PBC, the FDTD/PBC algorithm is proposed to study periodic structure consisting of plasma and vacuum. Then the reflection coefficient for the plasma slab from the FDTD/PBC algorithm is compared with the analytic results to show the validity of our technique. Finally, the reflection coefficients for the plasma photonic crystals are calculated using the FDTD/PBC algorithm to study the variation of bandgap characteristics with the incident angle and the plasma parameters. Thus it has provided the guiding sense for the actual manufacturing plasma photonic crystal. (general)

Incidence of cervical dysplasia and cervical cancer in women living with HIV in Denmark

DEFF Research Database (Denmark)

Thorsteinsson, K; Ladelund, Steen; Jensen-Fangel, S

2016-01-01

, which contains nationwide records of all pathology specimens. The cumulative incidence and hazard ratios (HRs) for time from inclusion to first cervical intraepithelial neoplasia (CIN)/ICC and time from first normal cervical cytology result to first CIN/ICC were estimated. Sensitivity analyses were......OBJECTIVES: Women living with HIV (WLWH) are reportedly at increased risk of invasive cervical cancer (ICC). A recent publication found that WLWH in Denmark attend the national ICC screening programme less often than women in the general population. We aimed to estimate the incidence of cervical...... in both groups were adherent to the national ICC screening programme and had a normal baseline cytology, incidences of CIN and ICC were comparable. CONCLUSIONS: Overall, WLWH developed more cervical disease than controls. Yet, in WLWH and controls adherent to the national ICC screening programme...

Angular reflectance of suspended gold, aluminum and silver nanospheres on a gold film: Effects of concentration and size distribution

International Nuclear Information System (INIS)

Aslan, Mustafa M.; Wriedt, Thomas

2010-01-01

In this article, we describe a parametric study of the effects of the size distribution (SD) and the concentration of nanospheres in ethanol on the angular reflectance. Calculations are based on an effective medium approach in which the effective dielectric constant of the mixture is obtained using the Maxwell-Garnett formula. The detectable size limits of gold, aluminum, and silver nanospheres on a 50-nm-thick gold film are calculated to investigate the sensitivity of the reflectance to the SD and the concentration of the nanospheres. The following assumptions are made: (1) the total number of particles in the unit volume of suspension is constant, (2) the nanospheres in the suspension on a gold film have a SD with three different concentrations, and (3) there is no agglomeration and the particles have a log-normal SD, where the effective diameter, d eff and the effective variance, ν eff are given. The dependence of the reflectance on the d eff , ν eff , and the width of the SD are also investigated numerically. The angular variation of the reflectance as a function of the incident angle shows a strong dependence on the effective size of the metallic nanospheres. The results confirm that the size of the nanospheres (d eff o and 75 o for a given concentration with a particular SD.

Characteristics of Wave Reflection for Vertical and Slit Caissons with Porous Structures

Directory of Open Access Journals (Sweden)

Tae-Hwa Jung

2012-01-01

Full Text Available Offshore structures are occasionally located at a relatively deep water region, the outside of breakwater. In this case, these structures may be damaged by the supposition of incident and reflected waves from a vertical breakwater. To prevent the damage, the reflected waves are controlled by installing porous structures at the face of the vertical breakwater. In this study, numerical experiments are carried out to identify the characteristics of wave reflection from the porous structures installing in front of a vertical or slit caisson.

An evaluation of directional analysis techniques for multidirectional, partially reflected waves .1. numerical investigations

DEFF Research Database (Denmark)

Ilic, C; Chadwick, A; Helm-Petersen, Jacob

2000-01-01

, non-phased locked methods are more appropriate. In this paper, the accuracy of two non-phased locked methods of directional analysis, the maximum likelihood method (MLM) and the Bayesian directional method (BDM) have been quantitatively evaluated using numerical simulations for the case...... of multidirectional waves with partial reflections. It is shown that the results are influenced by the ratio of distance from the reflector (L) to the length of the time series (S) used in the spectral analysis. Both methods are found to be capable of determining the incident and reflective wave fields when US > 0......Recent studies of advanced directional analysis techniques have mainly centred on incident wave fields. In the study of coastal structures, however, partially reflective wave fields are commonly present. In the near structure field, phase locked methods can be successfully applied. In the far field...

Reflective and refractive objects for mixed reality.

Science.gov (United States)

Knecht, Martin; Traxler, Christoph; Winklhofer, Christoph; Wimmer, Michael

2013-04-01

In this paper, we present a novel rendering method which integrates reflective or refractive objects into a differential instant radiosity (DIR) framework usable for mixed-reality (MR) applications. This kind of objects are very special from the light interaction point of view, as they reflect and refract incident rays. Therefore they may cause high-frequency lighting effects known as caustics. Using instant-radiosity (IR) methods to approximate these high-frequency lighting effects would require a large amount of virtual point lights (VPLs) and is therefore not desirable due to real-time constraints. Instead, our approach combines differential instant radiosity with three other methods. One method handles more accurate reflections compared to simple cubemaps by using impostors. Another method is able to calculate two refractions in real-time, and the third method uses small quads to create caustic effects. Our proposed method replaces parts in light paths that belong to reflective or refractive objects using these three methods and thus tightly integrates into DIR. In contrast to previous methods which introduce reflective or refractive objects into MR scenarios, our method produces caustics that also emit additional indirect light. The method runs at real-time frame rates, and the results show that reflective and refractive objects with caustics improve the overall impression for MR scenarios.

Secondary electron emission of sapphire tungsten molybdenum and titanium for Maxwellian incident electrons

International Nuclear Information System (INIS)

Saussez-Hublet, M.-C.; Harbour, P.J.

1980-06-01

The second electron emission coefficient of various materials, namely titanium, molybdenum, tungsten and sapphire, has been calculated for a Maxwellian energy distribution from data for a normally incident monoenergetic beam of primary electrons. The most significant difference from the monoenergetic case occurs at low energies. In addition the influence of the incident angle of the electrons is discussed. (author)

STRATEG - an incident training system for thermohydraulic effects and principles

International Nuclear Information System (INIS)

Rehn, H.; Majohr, N.

1993-01-01

STRATEG is a 1:10 scale glass model of a PWR (Biblis B reactor coolant circuit) built by RWE in 1986 on the site of the Biblis plant as a training model. The model can be used for training of normal operation and incident situations since all important operating and incident sequences of a PWR can be simulated. Thermodynamic phenomena can also be demonstrated occurring under various operating situations and in particular associated with malfunctions. (Z.S.) 1 tab., 3 figs., 1 ref

Optical fringe-reflection deflectometry with bundle adjustment

Science.gov (United States)

Xiao, Yong-Liang; Li, Sikun; Zhang, Qican; Zhong, Jianxin; Su, Xianyu; You, Zhisheng

2018-06-01

Liquid crystal display (LCD) screens are located outside of a camera's field of view in fringe-reflection deflectometry. Therefore, fringes that are displayed on LCD screens are obtained through specular reflection by a fixed camera. Thus, the pose calibration between the camera and LCD screen is one of the main challenges in fringe-reflection deflectometry. A markerless planar mirror is used to reflect the LCD screen more than three times, and the fringes are mapped into the fixed camera. The geometrical calibration can be accomplished by estimating the pose between the camera and the virtual image of fringes. Considering the relation between their pose, the incidence and reflection rays can be unified in the camera frame, and a forward triangulation intersection can be operated in the camera frame to measure three-dimensional (3D) coordinates of the specular surface. In the final optimization, constraint-bundle adjustment is operated to refine simultaneously the camera intrinsic parameters, including distortion coefficients, estimated geometrical pose between the LCD screen and camera, and 3D coordinates of the specular surface, with the help of the absolute phase collinear constraint. Simulation and experiment results demonstrate that the pose calibration with planar mirror reflection is simple and feasible, and the constraint-bundle adjustment can enhance the 3D coordinate measurement accuracy in fringe-reflection deflectometry.

Trends in adult leukemia incidence and survival in Denmark, 1943-2003

DEFF Research Database (Denmark)

Thygesen, Lau Caspar; Nielsen, Ove Juul; Johansen, Christoffer

2009-01-01

The etiology of leukemia is largely unknown. Ecological data indicating trends in incidence and survival can provide information about changes in risk factors, can reflect underlying changes in diagnostic classification, and can measure therapeutic advances. From the records of the Danish Cancer...... Registry with registration starting from 1943, we calculated age-specific, period-specific, and age-standardized (world standard) incidence rates of chronic lymphoid leukemia (CLL), acute lymphoid leukemia (ALL), chronic myeloid leukemia (CML), and acute myeloid leukemia (AML) for persons above the age...... of 18. Kaplan-Meier survival curves and median survival times were calculated. Between 1943 and 2003, there were 26,036 cases of leukemia reported. The age-specific incidence rates of CLL, CML, and AML were higher for older men and women, while the incidence rates of ALL by age were more homogeneous...

Split-field FDTD method for oblique incidence study of periodic dispersive metallic structures.

Science.gov (United States)

Baida, F I; Belkhir, A

2009-08-15

The study of periodic structures illuminated by a normally incident plane wave is a simple task that can be numerically simulated by the finite-difference time-domain (FDTD) method. On the contrary, for off-normal incidence, a widely modified algorithm must be developed in order to bypass the frequency dependence appearing in the periodic boundary conditions. After recently implementing this FDTD algorithm for pure dielectric materials, we here extend it to the study of metallic structures where dispersion can be described by analytical models. The accuracy of our code is demonstrated through comparisons with already-published results in the case of 1D and 3D structures.

Liquid Carbon Reflectivity at 19 nm

Directory of Open Access Journals (Sweden)

Riccardo Mincigrucci

2015-01-01

Full Text Available We hereby report on a pump-probe reflectivity experiment conducted on amorphous carbon, using a 780 nm laser as a pump and a 19 nm FEL emission as probe. Measurements were performed at 50 degrees with respect to the surface normal to have an un-pumped reflectivity higher than 0.5%. A sub-10 fs time synchronization error could be obtained exploiting the nearly jitter-free capabilities of FERMI. EUV FEL-based experiments open the way to study the behaviour of a liquid carbon phase being unaffected by plasma screening.

Gravitational wave sources: reflections and echoes

Science.gov (United States)

Price, Richard H.; Khanna, Gaurav

2017-11-01

The recent detection of gravitational waves has generated interest in alternatives to the black hole interpretation of sources. A subset of such alternatives involves a prediction of gravitational wave ‘echoes’. We consider two aspects of possible echoes: first, general features of echoes coming from spacetime reflecting conditions. We find that the detailed nature of such echoes does not bear any clear relationship to quasi-normal frequencies. Second, we point out the pitfalls in the analysis of local reflecting ‘walls’ near the horizon of rapidly rotating black holes.

Gravitational wave sources: reflections and echoes

International Nuclear Information System (INIS)

Price, Richard H; Khanna, Gaurav

2017-01-01

The recent detection of gravitational waves has generated interest in alternatives to the black hole interpretation of sources. A subset of such alternatives involves a prediction of gravitational wave ‘echoes’. We consider two aspects of possible echoes: first, general features of echoes coming from spacetime reflecting conditions. We find that the detailed nature of such echoes does not bear any clear relationship to quasi-normal frequencies. Second, we point out the pitfalls in the analysis of local reflecting ‘walls’ near the horizon of rapidly rotating black holes. (paper)

Electro-optic polymeric reflection modulator based on plasmonic metamaterial

Science.gov (United States)

Abbas, A.; Swillam, M.

2018-02-01

A novel low power design for polymeric Electro-Optic reflection modulator is proposed based on the Extraordinary Reflection of light from multilayer structure consisting of a plasmonic metasurface with a periodic structure of sub wavelength circular apertures in a gold film above a thin layer of EO polymer and above another thin gold layer. The interference of the different reflected beams from different layer construct the modulated beam, The applied input driving voltage change the polymer refractive index which in turn determine whether the interference is constructive or destructive, so both phase and intensity modulation could be achieved. The resonant wavelength is tuned to the standard telecommunication wavelength 1.55μm, at this wavelength the reflection is minimum, while the absorption is maximum due to plasmonic resonance (PR) and the coupling between the incident light and the plasmonic metasurface.

Using wave intensity analysis to determine local reflection coefficient in flexible tubes.

Science.gov (United States)

Li, Ye; Parker, Kim H; Khir, Ashraf W

2016-09-06

It has been shown that reflected waves affect the shape and magnitude of the arterial pressure waveform, and that reflected waves have physiological and clinical prognostic values. In general the reflection coefficient is defined as the ratio of the energy of the reflected to the incident wave. Since pressure has the units of energy per unit volume, arterial reflection coefficient are traditionally defined as the ratio of reflected to the incident pressure. We demonstrate that this approach maybe prone to inaccuracies when applied locally. One of the main objectives of this work is to examine the possibility of using wave intensity, which has units of energy flux per unit area, to determine the reflection coefficient. We used an in vitro experimental setting with a single inlet tube joined to a second tube with different properties to form a single reflection site. The second tube was long enough to ensure that reflections from its outlet did not obscure the interactions of the initial wave. We generated an approximately half sinusoidal wave at the inlet of the tube and took measurements of pressure and flow along the tube. We calculated the reflection coefficient using wave intensity (R dI and R dI 0.5 ) and wave energy (R I and R I 0.5 ) as well as the measured pressure (R dP ) and compared these results with the reflection coefficient calculated theoretically based on the mechanical properties of the tubes. The experimental results show that the reflection coefficients determined by all the techniques we studied increased or decreased with distance from the reflection site, depending on the type of reflection. In our experiments, R dP , R dI 0.5 and R I 0.5 are the most reliable parameters to measure the mean reflection coefficient, whilst R dI and R I provide the best measure of the local reflection coefficient, closest to the reflection site. Additional work with bifurcations, tapered tubes and in vivo experiments are needed to further understand, validate the

Molecular dynamics study of the interactions of incident N or Ti atoms with the TiN(001) surface

International Nuclear Information System (INIS)

Xu, Zhenhai; Zeng, Quanren; Yuan, Lin; Qin, Yi; Chen, Mingjun; Shan, Debin

2016-01-01

Graphical abstract: - Highlights: • Interactions of incident N or Ti atoms with TiN(001) surface are studied by CMD. • The impact position of incident N on the surface determines the interaction modes. • Adsorption could occur due to the atomic exchange process. • Resputtering and reflection may simultaneously occur. • The initial sticking coefficient of N on TiN(001) is much smaller than that of Ti. - Abstract: The interaction processes between incident N or Ti atoms and the TiN(001) surface are simulated by classical molecular dynamics based on the second nearest-neighbor modified embedded-atom method potentials. The simulations are carried out for substrate temperatures between 300 and 700 K and kinetic energies of the incident atoms within the range of 0.5–10 eV. When N atoms impact against the surface, adsorption, resputtering and reflection of particles are observed; several unique atomic mechanisms are identified to account for these interactions, in which the adsorption could occur due to the atomic exchange process while the resputtering and reflection may simultaneously occur. The impact position of incident N atoms on the surface plays an important role in determining the interaction modes. Their occurrence probabilities are dependent on the kinetic energy of incident N atoms but independent on the substrate temperature. When Ti atoms are the incident particles, adsorption is the predominant interaction mode between particles and the surface. This results in the much smaller initial sticking coefficient of N atoms on the TiN(001) surface compared with that of Ti atoms. Stoichiometric TiN is promoted by N/Ti flux ratios larger than one.

Improved Topographic Normalization for Landsat TM Images by Introducing the MODIS Surface BRDF

Directory of Open Access Journals (Sweden)

Yanli Zhang

2015-05-01

Full Text Available In rugged terrain, the accuracy of surface reflectance estimations is compromised by atmospheric and topographic effects. We propose a new method to simultaneously eliminate atmospheric and terrain effects in Landsat Thematic Mapper (TM images based on a 30 m digital elevation model (DEM and Moderate Resolution Imaging Spectroradiometer (MODIS atmospheric products. Moreover, we define a normalized factor of a Bidirectional Reflectance Distribution Function (BRDF to convert the sloping pixel reflectance into a flat pixel reflectance by using the Ross Thick-Li Sparse BRDF model (Ambrals algorithm and MODIS BRDF/albedo kernel coefficient products. Sole atmospheric correction and topographic normalization were performed for TM images in the upper stream of the Heihe River Basin. The results show that using MODIS atmospheric products can effectively remove atmospheric effects compared with the Fast Line-of-Sight Atmospheric Analysis of Spectral Hypercubes (FLAASH model and the Landsat Climate Data Record (CDR. Moreover, superior topographic effect removal can be achieved by considering the surface BRDF when compared with the surface Lambertian assumption of topographic normalization.

Investigation of the reflection of fast neutrons

International Nuclear Information System (INIS)

Devillers, Christian; Hasselin, Gilbert

1964-10-01

The authors report the study of the reflection of fast neutrons on a plane plate having a finite and varying thickness and an infinite width. Calculations are performed by using a Monte-Carlo method which allows the number, the energy, the direction, the emergence point of neutrons reflected on a plate, to be computed with respect to the energy and direction of incident neutrons. The author present how paths, elastic and inelastic shocks, direction after shock are calculated. Different information are calculated: the numbers of elastic shocks, inelastic shocks and transmitted neutrons, the number, energy and dose albedo, the spectrum and angular distribution, the distribution of neutron in terms of energy and direction

Major Incident Hospital: Development of a Permanent Facility for Management of Incident Casualties.

Science.gov (United States)

Marres, Geertruid; Bemelman, Michael; van der Eijk, John; Leenen, Luke

2009-06-01

Preparation is essential to cope with the challenge of providing optimal care when there is a sudden, unexpected surge of casualties due to a disaster or major incident. By definition, the requirements of such cases exceed the standard care facilities of hospitals in qualitative or quantitative respects and interfere with the care of regular patients. To meet the growing demands to be prepared for disasters, a permanent facility to provide structured, prepared relief in such situations was developed. A permanent but reserved Major Incident Hospital (MIH) has been developed through cooperation between a large academic medical institution, a trauma center, a military hospital, and the National Poison Information Centre (NVIC). The infrastructure, organization, support systems, training and systematic working methods of the MIH are designed to create order in a chaotic, unexpected situation and to optimize care and logistics in any possible scenario. Focus points are: patient flow and triage, registration, communication, evaluation and training. Research and the literature are used to identify characteristic pitfalls due to the chaos associated with and the unexpected nature of disasters, and to adapt our organization. At the MIH, the exceptional has become the core business, and preparation for disaster and large-scale emergency care is a daily occupation. An Emergency Response Protocol enables admittance to the normally dormant hospital of up to 100 (in exceptional cases even 300) patients after a start-up time of only 15 min. The Patient Barcode Registration System (PBR) with EAN codes guarantees quick and adequate registration of patient data in order to facilitate good medical coordination and follow-up during a major incident. The fact that the hospital is strictly reserved for this type of care guarantees availability and minimizes impact on normal care. When it is not being used during a major incident, there is time to address training and research

Targeting safety improvements through identification of incident origination and detection in a near-miss incident learning system

International Nuclear Information System (INIS)

Novak, Avrey; Nyflot, Matthew J.; Ermoian, Ralph P.; Jordan, Loucille E.; Sponseller, Patricia A.; Kane, Gabrielle M.; Ford, Eric C.; Zeng, Jing

2016-01-01

Purpose: Radiation treatment planning involves a complex workflow that has multiple potential points of vulnerability. This study utilizes an incident reporting system to identify the origination and detection points of near-miss errors, in order to guide their departmental safety improvement efforts. Previous studies have examined where errors arise, but not where they are detected or applied a near-miss risk index (NMRI) to gauge severity. Methods: From 3/2012 to 3/2014, 1897 incidents were analyzed from a departmental incident learning system. All incidents were prospectively reviewed weekly by a multidisciplinary team and assigned a NMRI score ranging from 0 to 4 reflecting potential harm to the patient (no potential harm to potential critical harm). Incidents were classified by point of incident origination and detection based on a 103-step workflow. The individual steps were divided among nine broad workflow categories (patient assessment, imaging for radiation therapy (RT) planning, treatment planning, pretreatment plan review, treatment delivery, on-treatment quality management, post-treatment completion, equipment/software quality management, and other). The average NMRI scores of incidents originating or detected within each broad workflow area were calculated. Additionally, out of 103 individual process steps, 35 were classified as safety barriers, the process steps whose primary function is to catch errors. The safety barriers which most frequently detected incidents were identified and analyzed. Finally, the distance between event origination and detection was explored by grouping events by the number of broad workflow area events passed through before detection, and average NMRI scores were compared. Results: Near-miss incidents most commonly originated within treatment planning (33%). However, the incidents with the highest average NMRI scores originated during imaging for RT planning (NMRI = 2.0, average NMRI of all events = 1.5), specifically

Targeting safety improvements through identification of incident origination and detection in a near-miss incident learning system

Energy Technology Data Exchange (ETDEWEB)

Novak, Avrey; Nyflot, Matthew J.; Ermoian, Ralph P.; Jordan, Loucille E.; Sponseller, Patricia A.; Kane, Gabrielle M.; Ford, Eric C.; Zeng, Jing, E-mail: jzeng13@uw.edu [Department of Radiation Oncology, University of Washington Medical Center, 1959 NE Pacific Street, Campus Box 356043, Seattle, Washington 98195 (United States)

2016-05-15

Purpose: Radiation treatment planning involves a complex workflow that has multiple potential points of vulnerability. This study utilizes an incident reporting system to identify the origination and detection points of near-miss errors, in order to guide their departmental safety improvement efforts. Previous studies have examined where errors arise, but not where they are detected or applied a near-miss risk index (NMRI) to gauge severity. Methods: From 3/2012 to 3/2014, 1897 incidents were analyzed from a departmental incident learning system. All incidents were prospectively reviewed weekly by a multidisciplinary team and assigned a NMRI score ranging from 0 to 4 reflecting potential harm to the patient (no potential harm to potential critical harm). Incidents were classified by point of incident origination and detection based on a 103-step workflow. The individual steps were divided among nine broad workflow categories (patient assessment, imaging for radiation therapy (RT) planning, treatment planning, pretreatment plan review, treatment delivery, on-treatment quality management, post-treatment completion, equipment/software quality management, and other). The average NMRI scores of incidents originating or detected within each broad workflow area were calculated. Additionally, out of 103 individual process steps, 35 were classified as safety barriers, the process steps whose primary function is to catch errors. The safety barriers which most frequently detected incidents were identified and analyzed. Finally, the distance between event origination and detection was explored by grouping events by the number of broad workflow area events passed through before detection, and average NMRI scores were compared. Results: Near-miss incidents most commonly originated within treatment planning (33%). However, the incidents with the highest average NMRI scores originated during imaging for RT planning (NMRI = 2.0, average NMRI of all events = 1.5), specifically

Uniqueness in inverse elastic scattering with finitely many incident waves

International Nuclear Information System (INIS)

Elschner, Johannes; Yamamoto, Masahiro

2009-01-01

We consider the third and fourth exterior boundary value problems of linear isotropic elasticity and present uniqueness results for the corresponding inverse scattering problems with polyhedral-type obstacles and a finite number of incident plane elastic waves. Our approach is based on a reflection principle for the Navier equation. (orig.)

Data sets for hydrogen reflection and their use in neutral transport calculations

International Nuclear Information System (INIS)

Eckstein, W.; Heifetz, D.B.

1986-08-01

A realistic characterization of the interaction of ions and neutral particles with device walls is important for any edge plasma calculation. Present reflection models vary in detail and computational efficiency. This paper presents a data set for the distribution of the reflection coefficient, R N , over reflected energy, polar, and azimuthal angles, as functions of incident polar angle and energy. These results have been computed using a vectorized version of the TRIM Monte Carlo code. The data are stored using an algorithm for reducing the data into three one-dimensional distributions, resulting in a realistic reflection model which can be used very efficiently in plasma edge calculations. (orig.)

A Self-reflection in Developing Teaching Performance at the Classroom for English Foreign Language (Efl) Teachers

OpenAIRE

Karlinawati, Esih

2014-01-01

This paper deals with a topic self-reflection in developing teaching performance. Self-reflection is a vital skill to reflect and evaluate teachers' teaching performance in the classroom. However, there are many teachers running monotonous classes because they do not make a self-reflection. This consideration explores teachers' strengths and weaknesses in learning process. This research will help the teachers to maintain or eliminate critical incident on learning and teaching process. This re...

Measuring solar reflectance - Part I: Defining a metric that accurately predicts solar heat gain

Energy Technology Data Exchange (ETDEWEB)

Levinson, Ronnen; Akbari, Hashem; Berdahl, Paul [Heat Island Group, Environmental Energy Technologies Division, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States)

2010-09-15

Solar reflectance can vary with the spectral and angular distributions of incident sunlight, which in turn depend on surface orientation, solar position and atmospheric conditions. A widely used solar reflectance metric based on the ASTM Standard E891 beam-normal solar spectral irradiance underestimates the solar heat gain of a spectrally selective ''cool colored'' surface because this irradiance contains a greater fraction of near-infrared light than typically found in ordinary (unconcentrated) global sunlight. At mainland US latitudes, this metric R{sub E891BN} can underestimate the annual peak solar heat gain of a typical roof or pavement (slope {<=} 5:12 [23 ]) by as much as 89 W m{sup -2}, and underestimate its peak surface temperature by up to 5 K. Using R{sub E891BN} to characterize roofs in a building energy simulation can exaggerate the economic value N of annual cool roof net energy savings by as much as 23%. We define clear sky air mass one global horizontal (''AM1GH'') solar reflectance R{sub g,0}, a simple and easily measured property that more accurately predicts solar heat gain. R{sub g,0} predicts the annual peak solar heat gain of a roof or pavement to within 2 W m{sup -2}, and overestimates N by no more than 3%. R{sub g,0} is well suited to rating the solar reflectances of roofs, pavements and walls. We show in Part II that R{sub g,0} can be easily and accurately measured with a pyranometer, a solar spectrophotometer or version 6 of the Solar Spectrum Reflectometer. (author)

Measuring solar reflectance Part I: Defining a metric that accurately predicts solar heat gain

Energy Technology Data Exchange (ETDEWEB)

Levinson, Ronnen; Akbari, Hashem; Berdahl, Paul

2010-05-14

Solar reflectance can vary with the spectral and angular distributions of incident sunlight, which in turn depend on surface orientation, solar position and atmospheric conditions. A widely used solar reflectance metric based on the ASTM Standard E891 beam-normal solar spectral irradiance underestimates the solar heat gain of a spectrally selective 'cool colored' surface because this irradiance contains a greater fraction of near-infrared light than typically found in ordinary (unconcentrated) global sunlight. At mainland U.S. latitudes, this metric RE891BN can underestimate the annual peak solar heat gain of a typical roof or pavement (slope {le} 5:12 [23{sup o}]) by as much as 89 W m{sup -2}, and underestimate its peak surface temperature by up to 5 K. Using R{sub E891BN} to characterize roofs in a building energy simulation can exaggerate the economic value N of annual cool-roof net energy savings by as much as 23%. We define clear-sky air mass one global horizontal ('AM1GH') solar reflectance R{sub g,0}, a simple and easily measured property that more accurately predicts solar heat gain. R{sub g,0} predicts the annual peak solar heat gain of a roof or pavement to within 2 W m{sup -2}, and overestimates N by no more than 3%. R{sub g,0} is well suited to rating the solar reflectances of roofs, pavements and walls. We show in Part II that R{sub g,0} can be easily and accurately measured with a pyranometer, a solar spectrophotometer or version 6 of the Solar Spectrum Reflectometer.

Metrology and Alignment of Light Weight Grazing Incidence X-Ray Mirrors

Science.gov (United States)

Zhang, William; Content, David; Petre, Robert; Saha, Timo

2000-01-01

Metrology and alignment of light weight X-ray optics have been a challenge for two reasons: (1) that the intrinsic mirror quality and distortions caused by handling can not be easily separated, and (2) the diffraction limits of the visible light become a severe problem at the order of one arc-minute. Traditional methods of using a normal incident pencil or small parallel beam which monitors a tiny fraction of the mirror in question at a given time can not adequately monitor those distortions. We are developing a normal incidence setup that monitors a large fraction, if not the whole, of the mirror at any given time. It will allow us to align thin X-ray mirrors to-an accuracy of a few arc seconds or to a limit dominated by the mirror intrinsic quality.

Evaluation of directional normalization methods for Landsat TM/ETM+ over primary Amazonian lowland forests

Science.gov (United States)

Van doninck, Jasper; Tuomisto, Hanna

2017-06-01

Biodiversity mapping in extensive tropical forest areas poses a major challenge for the interpretation of Landsat images, because floristically clearly distinct forest types may show little difference in reflectance. In such cases, the effects of the bidirectional reflection distribution function (BRDF) can be sufficiently strong to cause erroneous image interpretation and classification. Since the opening of the Landsat archive in 2008, several BRDF normalization methods for Landsat have been developed. The simplest of these consist of an empirical view angle normalization, whereas more complex approaches apply the semi-empirical Ross-Li BRDF model and the MODIS MCD43-series of products to normalize directional Landsat reflectance to standard view and solar angles. Here we quantify the effect of surface anisotropy on Landsat TM/ETM+ images over old-growth Amazonian forests, and evaluate five angular normalization approaches. Even for the narrow swath of the Landsat sensors, we observed directional effects in all spectral bands. Those normalization methods that are based on removing the surface reflectance gradient as observed in each image were adequate to normalize TM/ETM+ imagery to nadir viewing, but were less suitable for multitemporal analysis when the solar vector varied strongly among images. Approaches based on the MODIS BRDF model parameters successfully reduced directional effects in the visible bands, but removed only half of the systematic errors in the infrared bands. The best results were obtained when the semi-empirical BRDF model was calibrated using pairs of Landsat observation. This method produces a single set of BRDF parameters, which can then be used to operationally normalize Landsat TM/ETM+ imagery over Amazonian forests to nadir viewing and a standard solar configuration.

Simple methods of aligning four-circle diffractometers with crystal reflections

Energy Technology Data Exchange (ETDEWEB)

Mitsui, Y [Tokyo Univ. (Japan). Faculty of Pharmaceutical Sciences

1979-08-01

Simple methods of aligning four-circle diffractometers with crystal reflections are devised. They provide the methods to check (1) perpendicularity of chi plane to the incident beam, (2) zero point of 2theta and linearity of focus-chi center-receiving aperture and (3) zero point of chi.

The current status of grazing incidence optics

International Nuclear Information System (INIS)

Aschenbach, B.

1983-01-01

The developments in the area of grazing incidence optics with emphasis on telescopes for use in X-ray astronomy are reviewed. The performance of existing high-resolution telescopes is outlined and compared with those expected from future missions like ROSAT and AXAF. Starting from the basic principles of X-ray reflection and scattering, an attempt is made to highlight the current understanding of X-ray mirror physics using new theoretical ideas as well as experimental laboratory results. (author)

Liquid Atomization Induced by Pulse Laser Reflection underneath Liquid Surface

Science.gov (United States)

Utsunomiya, Yuji; Kajiwara, Takashi; Nishiyama, Takashi; Nagayama, Kunihito; Kubota, Shiro; Nakahara, Motonao

2009-05-01

We observed a novel effect of pulse laser reflection at the interface between transparent materials with different refractive indices. The electric field intensity doubles when a laser beam is completely reflected from a material with a higher refractive index to a material with a lower index. This effect appreciably reduces pulse laser ablation threshold of transparent materials. We performed experiments to observe the entire ablation process for laser incidence on the water-air interface using pulse laser shadowgraphy with high-resolution film; the minimum laser fluence for laser ablation at the water-air interface was approximately 12-16 J/cm2. We confirmed that this laser ablation occurs only when the laser beam is incident on the water-air interface from water. Many slender liquid ligaments extend like a milk crown and seem to be atomized at the tip. Their detailed structures can be resolved only by pulse laser photography using high-resolution film.

Cyber Incidents Involving Control Systems

Energy Technology Data Exchange (ETDEWEB)

Robert J. Turk

2005-10-01

The Analysis Function of the US-CERT Control Systems Security Center (CSSC) at the Idaho National Laboratory (INL) has prepared this report to document cyber security incidents for use by the CSSC. The description and analysis of incidents reported herein support three CSSC tasks: establishing a business case; increasing security awareness and private and corporate participation related to enhanced cyber security of control systems; and providing informational material to support model development and prioritize activities for CSSC. The stated mission of CSSC is to reduce vulnerability of critical infrastructure to cyber attack on control systems. As stated in the Incident Management Tool Requirements (August 2005) ''Vulnerability reduction is promoted by risk analysis that tracks actual risk, emphasizes high risk, determines risk reduction as a function of countermeasures, tracks increase of risk due to external influence, and measures success of the vulnerability reduction program''. Process control and Supervisory Control and Data Acquisition (SCADA) systems, with their reliance on proprietary networks and hardware, have long been considered immune to the network attacks that have wreaked so much havoc on corporate information systems. New research indicates this confidence is misplaced--the move to open standards such as Ethernet, Transmission Control Protocol/Internet Protocol, and Web technologies is allowing hackers to take advantage of the control industry's unawareness. Much of the available information about cyber incidents represents a characterization as opposed to an analysis of events. The lack of good analyses reflects an overall weakness in reporting requirements as well as the fact that to date there have been very few serious cyber attacks on control systems. Most companies prefer not to share cyber attack incident data because of potential financial repercussions. Uniform reporting requirements will do much to make this

Incidence of centrally positioned nuclei in mouse masticatory muscle fibers

DEFF Research Database (Denmark)

Vilmann, A; Vilmann, H; Kirkeby, S

1989-01-01

Cross-sections of normal digastric, temporalis and masseter muscles from 7- and 30-week-old mice were studied for centrally positioned nuclei. Such nuclei were inhomogeneously distributed throughout each muscle and varied markedly between specimens. The incidence of centrally positioned nuclei in...

Experimental analysis of bidirectional reflectance distribution function cross section conversion term in direction cosine space.

Science.gov (United States)

Butler, Samuel D; Nauyoks, Stephen E; Marciniak, Michael A

2015-06-01

Of the many classes of bidirectional reflectance distribution function (BRDF) models, two popular classes of models are the microfacet model and the linear systems diffraction model. The microfacet model has the benefit of speed and simplicity, as it uses geometric optics approximations, while linear systems theory uses a diffraction approach to compute the BRDF, at the expense of greater computational complexity. In this Letter, nongrazing BRDF measurements of rough and polished surface-reflecting materials at multiple incident angles are scaled by the microfacet cross section conversion term, but in the linear systems direction cosine space, resulting in great alignment of BRDF data at various incident angles in this space. This results in a predictive BRDF model for surface-reflecting materials at nongrazing angles, while avoiding some of the computational complexities in the linear systems diffraction model.

Optical Reflectance Measurements for Commonly Used Reflectors

Science.gov (United States)

Janecek, Martin; Moses, William W.

2008-08-01

When simulating light collection in scintillators, modeling the angular distribution of optical light reflectance from surfaces is very important. Since light reflectance is poorly understood, either purely specular or purely diffuse reflectance is generally assumed. In this paper we measure the optical reflectance distribution for eleven commonly used reflectors. A 440 nm, output power stabilized, un-polarized laser is shone onto a reflector at a fixed angle of incidence. The reflected light's angular distribution is measured by an array of silicon photodiodes. The photodiodes are movable to cover 2pi of solid angle. The light-induced current is, through a multiplexer, read out with a digital multimeter. A LabVIEW program controls the motion of the laser and the photodiode array, the multiplexer, and the data collection. The laser can be positioned at any angle with a position accuracy of 10 arc minutes. Each photodiode subtends 6.3deg, and the photodiode array can be positioned at any angle with up to 10 arc minute angular resolution. The dynamic range for the current measurements is 10 5:1. The measured light reflectance distribution was measured to be specular for several ESR films as well as for aluminum foil, mostly diffuse for polytetrafluoroethylene (PTFE) tape and titanium dioxide paint, and neither specular nor diffuse for Lumirrorreg, Melinexreg and Tyvekreg. Instead, a more complicated light distribution was measured for these three materials.

Adjustable wideband reflective converter based on cut-wire metasurface

International Nuclear Information System (INIS)

Zhang, Linbo; Zhou, Peiheng; Chen, Haiyan; Lu, Haipeng; Xie, Jianliang; Deng, Longjiang

2015-01-01

We present the design, analysis, and measurement of a broadband reflective converter using a cut-wire (CW) metasurface. Based on the characteristics of LC resonances, the proposed reflective converter can rotate a linearly polarized (LP) wave into its cross-polarized wave at three resonance frequencies, or convert the LP wave to a circularly polarized (CP) wave at two other resonance frequencies. Furthermore, the broad-band properties of the polarization conversion can be sustained when the incident wave is a CP wave. The polarization states can be adjusted easily by changing the length and width of the CW. The measured results show that a polarization conversion ratio (PCR) over 85% can be achieved from 6.16 GHz to 16.56 GHz for both LP and CP incident waves. The origin of the polarization conversion is interpreted by the theory of microwave antennas, with equivalent impedance and electromagnetic (EM) field distributions. With its simple geometry and multiple broad frequency bands, the proposed converter has potential applications in the area of selective polarization control. (paper)

Controllable transmission and total reflection through an impedance-matched acoustic metasurface

KAUST Repository

Mei, Jun

2014-12-02

A general design paradigm for a novel type of acoustic metasurface is proposed by introducing periodically repeated supercells on a rigid thin plate, where each supercell contains multiple cut-through slits that are filled with materials possessing different refractive indices but the same impedance as that of the host medium. When the wavelength of the incident wave is smaller than the periodicity, the direction of the transmitted wave with nearly unity transmittance can be chosen by engineering the phase discontinuities along the transverse direction. When the wavelength is larger than the periodicity, even though the metasurface is impedance matched to the host medium, most of the incident energy is reflected back and the remaining portion is converted into a surface-bound mode. We show that both the transmitted wave control and the high reflection with the surface mode excitation can be interpreted by a unified analytic model based on mode-coupling theory. Our general design principle not only supplies the functionalities of reflection-type acoustic metasurfaces, but also exhibits unprecedented flexibility and efficiency in various domains of wave manipulation for possible applications in fields like refracting, collimating, focusing or absorbing wave energy.

Determination of hot carrier energy distributions from inversion of ultrafast pump-probe reflectivity measurements.

Science.gov (United States)

Heilpern, Tal; Manjare, Manoj; Govorov, Alexander O; Wiederrecht, Gary P; Gray, Stephen K; Harutyunyan, Hayk

2018-05-10

Developing a fundamental understanding of ultrafast non-thermal processes in metallic nanosystems will lead to applications in photodetection, photochemistry and photonic circuitry. Typically, non-thermal and thermal carrier populations in plasmonic systems are inferred either by making assumptions about the functional form of the initial energy distribution or using indirect sensors like localized plasmon frequency shifts. Here we directly determine non-thermal and thermal distributions and dynamics in thin films by applying a double inversion procedure to optical pump-probe data that relates the reflectivity changes around Fermi energy to the changes in the dielectric function and in the single-electron energy band occupancies. When applied to normal incidence measurements our method uncovers the ultrafast excitation of a non-Fermi-Dirac distribution and its subsequent thermalization dynamics. Furthermore, when applied to the Kretschmann configuration, we show that the excitation of propagating plasmons leads to a broader energy distribution of electrons due to the enhanced Landau damping.

Theory of relativistic radiation reflection from plasmas

Science.gov (United States)

Gonoskov, Arkady

2018-01-01

We consider the reflection of relativistically strong radiation from plasma and identify the physical origin of the electrons' tendency to form a thin sheet, which maintains its localisation throughout its motion. Thereby, we justify the principle of relativistic electronic spring (RES) proposed in [Gonoskov et al., Phys. Rev. E 84, 046403 (2011)]. Using the RES principle, we derive a closed set of differential equations that describe the reflection of radiation with arbitrary variation of polarization and intensity from plasma with an arbitrary density profile for an arbitrary angle of incidence. We confirm with ab initio PIC simulations that the developed theory accurately describes laser-plasma interactions in the regime where the reflection of relativistically strong radiation is accompanied by significant, repeated relocation of plasma electrons. In particular, the theory can be applied for the studies of plasma heating and coherent and incoherent emissions in the RES regime of high-intensity laser-plasma interaction.

Elder Abuse and Black Americans: Incidence, Correlates, Treatment and Prevention.

Science.gov (United States)

Cazenave, Noel A.

Existing evidence on family violence rates by age and race as well as the available data on race and physical elder abuse incidence rates suggests that because such data are not based on random or representative samples and tend to reflect a "sampling artifact" of the particular client populations served by the professionals surveyed,…

Improving imaging quality using least-squares reverse time migration: application to data from Bohai basin

KAUST Repository

Zhang, Hao; Liu, Qiancheng; Wu, Jizhong

2017-01-01

Least-squares reverse time migration (LSRTM) is a seismic imaging technique based on linear inversion, which usually aims to improve the quality of seismic image through removing the acquisition footprint, suppressing migration artifacts, and enhancing resolution. LSRTM has been shown to produce migration images with better quality than those computed by conventional migration. In this paper, our derivation of LSRTM approximates the near-incident reflection coefficient with the normal-incident reflection coefficient, which shows that the reflectivity term defined is related to the normal-incident reflection coefficient and the background velocity. With reflected data, LSRTM is mainly sensitive to impedance perturbations. According to an approximate relationship between them, we reformulate the perturbation related system into a reflection-coefficient related one. Then, we seek the inverted image through linearized iteration. In the proposed algorithm, we only need the migration velocity for LSRTM considering that the density changes gently when compared with migration velocity. To validate our algorithms, we first apply it to a synthetic case and then a field data set. Both applications illustrate that our imaging results are of good quality.

Improving imaging quality using least-squares reverse time migration: application to data from Bohai basin

KAUST Repository

Zhang, Hao

2017-07-07

Least-squares reverse time migration (LSRTM) is a seismic imaging technique based on linear inversion, which usually aims to improve the quality of seismic image through removing the acquisition footprint, suppressing migration artifacts, and enhancing resolution. LSRTM has been shown to produce migration images with better quality than those computed by conventional migration. In this paper, our derivation of LSRTM approximates the near-incident reflection coefficient with the normal-incident reflection coefficient, which shows that the reflectivity term defined is related to the normal-incident reflection coefficient and the background velocity. With reflected data, LSRTM is mainly sensitive to impedance perturbations. According to an approximate relationship between them, we reformulate the perturbation related system into a reflection-coefficient related one. Then, we seek the inverted image through linearized iteration. In the proposed algorithm, we only need the migration velocity for LSRTM considering that the density changes gently when compared with migration velocity. To validate our algorithms, we first apply it to a synthetic case and then a field data set. Both applications illustrate that our imaging results are of good quality.

Residential Radon and Brain Tumour Incidence in a Danish Cohort

DEFF Research Database (Denmark)

Bräuner, Elvira V.; Andersen, Zorana J.; Andersen, Claus Erik

2013-01-01

Background: Increased brain tumour incidence over recent decades may reflect improved diagnostic methods and clinical practice, but remain unexplained. Although estimated doses are low a relationship between radon and brain tumours may exist. Objective: To investigate the long-term effect of expo...... significant associations and exposure-response patterns between long-term residential radon exposure radon in a general population and risk of primary brain tumours, adding new knowledge to this field. This finding could be chance and needs to be challenged in future studies.......Background: Increased brain tumour incidence over recent decades may reflect improved diagnostic methods and clinical practice, but remain unexplained. Although estimated doses are low a relationship between radon and brain tumours may exist. Objective: To investigate the long-term effect...... of exposure to residential radon on the risk of primary brain tumour in a prospective Danish cohort. Methods: During 1993–1997 we recruited 57,053 persons. We followed each cohort member for cancer occurrence from enrolment until 31 December 2009, identifying 121 primary brain tumour cases. We traced...

Grazing incidence Fe-line telescopes using W/B4C multilayers

DEFF Research Database (Denmark)

Joensen, K. D.; Gorenstein, P.; Christensen, Finn Erland

1995-01-01

The loss of throughput observed at higher energies for traditional grazing-incidence X-ray telescopes coated with high-Z elements can be partly countered by employing multilayers on the outermost reflectors. Using 8-keV reflectivity data from a periodic W/B4C multilayer, the expected performance...

Nontuberculous mycobacteria: incidence in Southwest Ireland from 1987 to 2000.

LENUS (Irish Health Repository)

Kennedy, M P

2012-02-03

SETTING: The Southwest of Ireland (Counties Cork and Kerry) 1987-2000, average population 549,500. OBJECTIVE: Nontuberculous mycobacteria (NTM) cause significant morbidity worldwide and the study of epidemiology and characteristics helps in their prevention and treatment. This study was performed to determine the incidence of NTM disease in comparison to Mycobacterium tuberculosis (M. tuberculosis) and Mycobacterium bovis (M. bovis) in Southwest Ireland, over the above time period. DESIGN: A retrospective study was carried out in all human isolates of NTM, M. tuberculosis and M. bovis between 1987 and 2000, in the Southwest Region of Ireland. RESULTS: The mean incidence of NTM (0.4\\/100,000 population) has risen since 1995, principally of pulmonary Mycobacterium avium intracellulare complex (MAC). The annual incidence of M. tuberculosis in humans over 14 years in the same region was 971\\/100,000 population with a significant reduction since 1994 and M. bovis remained constant at 0.5\\/100,000 population. CONCLUSION: The increasing incidence of disease causing NTM noted in Southwest Ireland reflects global data and is surmised to be due to an ageing population, increased incidence related to chronic fibrotic lung disease, and environmental mycobacterial factors.

Decline in Weight and Incident Mild Cognitive Impairment: Mayo Clinic Study of Aging

Science.gov (United States)

Alhurani, Rabe E.; Vassilaki, Maria; Aakre, Jeremiah; Mielke, Michelle M.; Kremers, Walter K.; Machulda, Mary M.; Geda, Yonas E.; Knopman, David S.; Peterson, Ronald C.; Roberts, Rosebud O.

2016-01-01

IMPORTANCE Unintentional weight loss has been associated with risk of dementia. Since mild cognitive impairment (MCI) is a prodromal stage for dementia, we sought to evaluate whether changes in weight and body mass index (BMI) may predict incident MCI. OBJECTIVE To investigate the association of change in weight and BMI with risk of MCI. DESIGN, SETTING, AND PARTICIPANTS A population-based, prospective study of participants aged 70 years and older from the Mayo Clinic Study of Aging. Maximum weight and height in midlife (aged 40 to 65 years old) were retrospectively ascertained from the medical records of participants using a medical records linkage system. MAIN OUTCOMES MEASURES Participants were evaluated for cognitive outcomes of normal cognition, MCI, or dementia at baseline and prospectively assessed for incident events at each 15-month evaluation. The association of rate of change in weight and body mass index with risk of MCI was investigated using proportional hazards models. RESULTS Over a mean follow-up of 4.4 years, 524 of 1895 cognitively normal participants developed incident MCI. The mean (standard deviation) rate of weight change per decade from midlife to study entry was greater for individuals who developed incident MCI vs. those who remained cognitively normal (−2.0 (5.1) vs. −1.2 (4.9) kg; p = 0.006). A greater decline in weight per decade was associated with an increased risk of incident MCI (hazard ratio [HR] 95% confidence interval [CI], 1.04 [1.02, 1.06], p weight loss of 5 kg/decade corresponds to a 24% increase in risk of MCI (HR=1.24). Higher decline in BMI per decade was also associated with incident MCI (HR, 1.08, 95% CI = [1.03, 1.13], p = 0.003). CONCLUSIONS AND RELEVANCE These findings suggest that declining weight from midlife to late-life is a marker for MCI and may help identify persons at increased risk for MCI. PMID:26831542

Study of the reflection of fast neutrons by a simple theory of shock. Application to iron

International Nuclear Information System (INIS)

Devillers, Christian; Hasselin, Gilbert

1964-10-01

By using a first shock theory, the authors report the calculation of an albedo current for fast neutrons, i.e. the rate between the reflected current per cm 2 of plate and the incident current on the same cm 2 . They also compute the spectrum and the angular distribution of reflected neutrons. These calculations are performed by means of three specific software: Psyche 1 for the determination of the albedo due to elastic scattering, and Psyche 2 and 3 for inelastic scattering (the first one addresses incident neutrons with an energy 0.86 and 5 MeV, and the second one the 5-12 MeV energy band). Hypotheses for each calculation are presented, as well as calculation principles and methods. Results are briefly presented and discussed in terms of albedo evolution with respect to incidence and to plate thickness

Broadband reflective multi-polarization converter based on single-layer double-L-shaped metasurface

Science.gov (United States)

Mao, Chenyang; Yang, Yang; He, Xiaoxiang; Zheng, Jingming; Zhou, Chun

2017-12-01

In this paper, a broadband reflective multi-polarization converter based on single-layer double-L-shaped metasurface is proposed. The proposed metasurface can effectively convert linear-polarized (TE/TM) incident wave into the reflected wave with three different polarizations within the frequency bands of 5.5-22.75 GHz. Based on the electric and magnetic resonant features of the double-L-shaped structure, the proposed metasurface can convert linearly polarized waves into cross-polarized waves at three resonant frequency bands. Furthermore, the incident linearly polarized waves can be effectively converted into left/right handed circular-polarized (LHCP and RHCP) waves at other four non-resonance frequency bands. Thus, the proposed metasurface can be regarded as a seven-band multi-polarization converter. The prototype of the proposed polarization converter is analyzed and measured. Both simulated and measured results show the 3-dB axis ratio bandwidth of circular polarization bands and the high polarization conversion efficiency of cross-polarization bands when the incident wave changes from 0° to 30° at both TE and TM modes.

Effect of FEL induced ionization on X-ray reflectivity of multilayers

Energy Technology Data Exchange (ETDEWEB)

Ksenzov, Dmitriy; Grigorian, Souren; Pietsch, Ullrich [University of Siegen (Germany)

2009-07-01

The VUV-FEL in Hamburg (FLASH) emits short-pulse radiation with wavelengths from 6 to 30 nm and a pulse length of 10-50 fs. The FLASH wavelength allows x-ray diffraction experiments at periodical multilayer's structures acting as 1D crystal. The probe of depth selective interaction of the high-intense x-ray short pulse with these objects can be used to obtain information about possible electronic excitation and various recombination processes inside multilayers. As known from recent experiments at FLASH, the later ones are most likely using highly intense FEL radiation. The ML reflectivity is analyzed for case of that the optical parameters are changing as function of the depth of the penetrating incident pulse into the multilayer. The response is studied for the model system La/B{sub 4}C using two experimental conditions both at fixed incidence angle: 1) the energy of the incident pulses, E, coincides with the energy of the 1st order multilayer Bragg peak, E{sub B}, of the reflection curve, and 2) the energy of incident pulse differs by a small dE from E{sub B}. The ML response to a given sub-pulse differs for both conditions. However, there is a clear fingerprint of ionization for both conditions for the case that E is close to the K-absorption edge of B-atoms. Our results support respective efforts to measure the optical parameters of solids under high-intense FEL radiation.

Use of reflective surfaces on roadway embankment

DEFF Research Database (Denmark)

Jørgensen, Anders Stuhr; Doré, Guy

2007-01-01

adherence characteristics for roadway use. In Kangerlussuaq Airport, western Greenland, ground-penetrating radar (GPR) has been used to compare the variation of the frost table underneath a normal black asphalt surface and a more reflective surface (white paint). The GPR results have shown a clear...

Label-Free and Real-Time Monitor of Binding and Dissociation Processes between Protein A and Swine IgG by Oblique-Incidence Reflectivity Difference Method

International Nuclear Information System (INIS)

He Li-Ping; Liu Shuang; Dai Jun; Lu Hui-Bin; Jin Kui-Juan; Yang Guo-Zhen; Wu Lin; Liu Guo-Zhen; Wei Han-Fu

2015-01-01

Life science has a need for detection methods that are label-free and real-time. In this paper, we have selected staphylococcal protein A (SPA) and swine immunoglobulin G (IgG), and monitor the bindings between SPA and swine IgG with different concentrations, as well as the dissociations of SPA-swine IgG complex in different pH values of phosphate buffer by oblique-incidence reflectivity difference (OIRD) in a label-free and real-time fashion. We obtain the ON and OFF reaction dynamic curves corresponding to the bindings and dissociations of SPA and swine IgG. Through our analysis of the experimental results, we have been able to obtain the damping coefficients and the dissociation time of SPA and swine IgG for different pH values of the phosphate buffer. The results prove that the OIRD technique is a competing method for monitoring the dynamic processes of biomolecule interaction and achieving the quantitative information of reaction kinetics. (general)

Low Group Delay Dispersion Optical Coating for Broad Bandwidth High Reflection at 45° Incidence, P Polarization of Femtosecond Pulses with 900 nm Center Wavelength

Directory of Open Access Journals (Sweden)

John C. Bellum

2016-03-01

Full Text Available We describe an optical coating design suitable for broad bandwidth high reflection (BBHR at 45° angle of incidence (AOI, P polarization (Ppol of femtosecond (fs laser pulses whose wavelengths range from 800 to 1000 nm. Our design process is guided by quarter-wave HR coating properties. The design must afford low group delay dispersion (GDD for reflected light over the broad, 200 nm bandwidth in order to minimize temporal broadening of the fs pulses due to dispersive alteration of relative phases between their frequency components. The design should also be favorable to high laser-induced damage threshold (LIDT. We base the coating on TiO2/SiO2 layer pairs produced by means of e-beam evaporation with ion-assisted deposition, and use OptiLayer Thin Film Software to explore designs starting with TiO2/SiO2 layers having thicknesses in a reverse chirped arrangement. This approach led to a design with R > 99% from 800 to 1000 nm and GDD < 20 fs2 from 843 to 949 nm (45° AOI, Ppol. The design’s GDD behaves in a smooth way, suitable for GDD compensation techniques, and its electric field intensities show promise for high LIDTs. Reflectivity and GDD measurements for the initial test coating indicate good performance of the BBHR design. Subsequent coating runs with improved process calibration produced two coatings whose HR bands satisfactorily meet the design goals. For the sake of completeness, we summarize our previously reported transmission spectra and LIDT test results with 800 ps, 8 ps and 675 fs pulses for these two coatings, and present a table of the LIDT results we have for all of our TiO2/SiO2 BBHR coatings, showing the trends with test laser pulse duration from the ns to sub-ps regimes.

Dependence of secondary electron emission on the incident angle and the energy of primary electrons bombarding bowl-structured beryllium surfaces

International Nuclear Information System (INIS)

Kawata, Jun; Ohya, Kaoru.

1994-01-01

A Monte Carlo simulation of the secondary electron emission from beryllium is combined with a model of bowl structure for surface roughness, for analyzing the difference between the electron emissions for normal and oblique incidences. At normal incidence, with increasing the roughness parameter H/W, the primary energy E pm at which the maximum electron yield occurs becomes higher, and at more than the E pm , the decrease in the yield is slower; where H and W are the depth and width of the bowl structure, respectively. The dispersion of incident angle to the microscopic surface causes a small increase in the yield at oblique incidence, whereas the blocking of primary electrons from bombarding the bottom of the structure causes an opposite trend. The strong anisotropy in the polar angular distribution with respect to the azimuthal angle is calculated at oblique incidence. (author)

An X-ray grazing incidence phase multilayer grating

CERN Document Server

Chernov, V A; Mytnichenko, S V

2001-01-01

An X-ray grazing incidence phase multilayer grating, representing a thin grating placed on a multilayer mirror, is proposed. A high efficiency of grating diffraction can be obtained by the possibility of changing the phase shift of the wave diffracted from the multilayer under the Bragg and total external reflection conditions. A grazing incidence phase multilayer grating consisting of Pt grating stripes on a Ni/C multilayer and optimized for the hard X-ray range was fabricated. Its diffraction properties were studied at photon energies of 7 and 8 keV. The obtained maximum value of the diffraction efficiency of the +1 grating order was 9% at 7 keV and 6.5% at 8 keV. The data obtained are in a rather good accordance with the theory.

Incidence and physical properties of PSE chicken meat in a commercial processing plant

Directory of Open Access Journals (Sweden)

RG Garcia

2010-12-01

Full Text Available It is known that PSE meat present important functional defects, such as low water holding capacity and ultimate pH, which may compromise the quality of further-processed meat products. In this study, L* (lightness, a* (redness, and b* (yellowness values of 500 chicken breast fillets were determined using a portable colorimeter (Minolta, model CR-400 in a commercial processing plant. Fillets were considered pale when their L* was >49. Out of those samples, 30 fillets with normal color and 30 pale fillets were evaluated as to pH, drip loss, cooking loss, water holding capacity, shear force, and submitted to sensorial analysis. An incidence of 10.20% PSE meat was determined. Pale and normal fillets presented significantly different (p0.05 between pale and normal fillets. Despite the significant differences in meat physical properties, these were not perceived by consumers in terms of tenderness, aspect, and flavor. The observed incidence of PSE may cause losses due to its low water retention capacity.

Secondary electron/reflected particle coincidence studies during slow highly charged ion-surface interactions

Energy Technology Data Exchange (ETDEWEB)

McGrath, C.T.; Szilagyi, Z.; Shah, M.B.; McCullough, R.W. [Queen' s Univ., Belfast, Northern Ireland (United Kingdom); Woolsey, J.M. [Stirling Univ. (United Kingdom). DBMS; Trassl, R.; Salzborn, E. [Giessen Univ. (Germany). Inst. fuer Kernphysik

2001-07-01

We have measured the secondary electron emission statistics (ES) for 5 keV N{sup q+} (q = 1-4) ions incident at 10 on polycrystalline aluminium, in coincidence with specularly reflected N{sup 0}. In this arrangement the kinetic contribution to secondary electron emission is minimised. The experimental data shows that the coincident electron yield, {gamma}, increases linearly with incident ion charge state. The kinetic emission contribution has also been determined from this data. The ES due to 2 and 4 keV He{sup 2+} impact on polycrystalline aluminium in coincidence with specularly reflected He{sup +} and He{sup 0} have also been determined. The process He{sup 2+} {yields} He{sup 0} yields a larger {gamma} value than the process He{sup 2+} {yields} He{sup +}. (orig.)

Incidence of lactase deficiency (LD) in gastroduodenal ulcer and gastric carcinoma

International Nuclear Information System (INIS)

Bahk, Yong Whee; Ahn, Kwan Shik; Kim, Chung Ja

1974-01-01

Lactase deficiency (LD) has been described in associated with peptic ulcer disease of the upper gastrointestinal tract, but little has been known as to the incidence of LD in the patients with ulcer disease of the upper GI tract or with gastric carcinoma. The purpose of the present study is to investigate the incidence of LD in gastric and/or duodenal ulcer disease and in gastric carcinoma, and to hypothesize the possible effect of these diseases on LD. Clinical materials consisted of 40 cases of active duodenal ulcer disease, 19 cases of benign gastric ulcer, 5 cases of multiple ulcers both in the stomach and duodenum, and 32 cases of gastric carcinoma. We used the lactose-barium test in diagnosing LD. X-ray findings were assessed according to the criteria described by Laws et al. and Preger and Amberg in the small-bowel film obtained at 30 minutes after the ingestion of some 200 ml of lactose-barium meal which contained 50 gm of lactose. Our clinical study revealed that the incidence of LD in duodenal ulcer was 50%, in gastric ulcer 57.9%, in gastric and duodenal ulcer 60%, and in gastric carcinoma 46.9%. The difference of incidence between each disease were statistically not significant, but the difference between the disease group and normal control was highly significant. The incidence of LD in disease group was nearly twice as high as that of normal control (27.7%). It is speculated that high incidence of LD in peptic ulcer disease of upper GI tract in particular may be associated with high acidity, the analog of which is found in Zollinger-Ellison syndrome. But high acidity is not a prominent feature in gastric carcinoma which is attended by almost equally high incidence of LD. It is therefore likely that the intolerability to lactose is caused by much complicated mechanism of versatile factors

Incidence of lactase deficiency (LD) in gastroduodenal ulcer and gastric carcinoma

Energy Technology Data Exchange (ETDEWEB)

Bahk, Yong Whee; Ahn, Kwan Shik; Kim, Chung Ja [St. Mary' s Hospital, Catholic Medical College, Seoul (Korea, Republic of)

1974-04-15

Lactase deficiency (LD) has been described in associated with peptic ulcer disease of the upper gastrointestinal tract, but little has been known as to the incidence of LD in the patients with ulcer disease of the upper GI tract or with gastric carcinoma. The purpose of the present study is to investigate the incidence of LD in gastric and/or duodenal ulcer disease and in gastric carcinoma, and to hypothesize the possible effect of these diseases on LD. Clinical materials consisted of 40 cases of active duodenal ulcer disease, 19 cases of benign gastric ulcer, 5 cases of multiple ulcers both in the stomach and duodenum, and 32 cases of gastric carcinoma. We used the lactose-barium test in diagnosing LD. X-ray findings were assessed according to the criteria described by Laws et al. and Preger and Amberg in the small-bowel film obtained at 30 minutes after the ingestion of some 200 ml of lactose-barium meal which contained 50 gm of lactose. Our clinical study revealed that the incidence of LD in duodenal ulcer was 50%, in gastric ulcer 57.9%, in gastric and duodenal ulcer 60%, and in gastric carcinoma 46.9%. The difference of incidence between each disease were statistically not significant, but the difference between the disease group and normal control was highly significant. The incidence of LD in disease group was nearly twice as high as that of normal control (27.7%). It is speculated that high incidence of LD in peptic ulcer disease of upper GI tract in particular may be associated with high acidity, the analog of which is found in Zollinger-Ellison syndrome. But high acidity is not a prominent feature in gastric carcinoma which is attended by almost equally high incidence of LD. It is therefore likely that the intolerability to lactose is caused by much complicated mechanism of versatile factors.

Estimating Forest fAPAR from Multispectral Landsat-8 Data Using the Invertible Forest Reflectance Model INFORM

Directory of Open Access Journals (Sweden)

Huili Yuan

2015-06-01

Full Text Available The estimation of the Fraction of Absorbed Photosynthetically Active Radiation in forests (forest fAPAR from multi-spectral Landsat-8 data is investigated in this paper using a physically based radiative transfer model (Invertible Forest Reflectance Model, INFORM combined with an inversion strategy based on artificial neural nets (ANN. To derive the forest fAPAR for the Dabie mountain test site in China in 30 m spatial resolution (size approximately 3000 km2, a database of forest canopy spectral reflectances was simulated with INFORM taking into account structural variables such as leaf area index (LAI, crown coverage and stem density as well as leaf composition. To establish the relationship between forest fAPAR and the reflectance modeled by INFORM, a logarithmic relationship between LAI and fAPAR was used previously established using on-site field measurements. On this basis, predictive models between Landsat-8 reflectance and fAPAR were established using an artificial neural network. After calibrating INFORM for the test site, forty-two forest stands were used to validate the performance of the method. The results show that spectral signatures modeled by INFORM correspond reasonably well with the forest canopy reflectance spectra derived from Landsat data. Deviations increase with increasing angle between surface normal of the hilly terrain and sun incidence. The comparison of estimated and measured fAPAR (R2 = 0.47, RMSE = 0.11 demonstrates that INFORM can be inverted using neural nets to provide acceptable estimates of forest fAPAR. The accuracy of the predictions increased significantly when excluding pixels located in very steep terrain. This demonstrates that the applied topographic correction was not sufficiently accurate and should be improved for making optimum use of radiative transfer models such as INFORM.

Graphite irradiated by swift heavy ions under grazing incidence

CERN Document Server

Liu, J; Müller, C; Neumann, R

2002-01-01

Highly oriented pyrolytic graphite is irradiated with various heavy projectiles (Ne, Ni, Zn, Xe and U) in the MeV to GeV energy range under different oblique angles of incidence. Using scanning tunneling microscopy, the impact zones are imaged as hillocks protruding from the surface. The diameter of surface-grazing tracks varies between 3 nm (Ne) and 6 nm (U), which is about twice as large as under normal beam incidence. Exclusively for U and Xe projectiles, grazing tracks exhibit long comet-like tails consisting of successive little bumps indicating that the damage along the ion path is discontinuous even for highest electronic stopping powers.

Surface characterization of selected polymer thin films by total-reflection x-ray fluorescence spectroscopy and x-ray reflectivity

International Nuclear Information System (INIS)

Innis, Vallerie Ann A.

2006-01-01

Development of available x-ray characterizations tools for grazing incidence techniques was done to be able to probe nano-size thin films. Alignment of a Philips x-ray powder diffractometer was improved to let it perform as an x-ray reflectometer. X-ray reflectometry was coupled with total-reflection x-ray fluorescence spectroscopy. Evaluation of the performance of this grazing incidence techniques was done by preparing polymer thin films of carboxymethylcellulose, carrageenan and polyvinylpyrrolidone (PVP). The thickness of the films were varied by varying the process parameters such as concentration, spin speed and spin time. Angle-dispersive total-reflection x-ray fluorescence spectroscopy profiles of three films showed film formation only in carrageenan and PVP. For both carrageenan and PVP, an increase in concentration yielded a corresponding increase in intensity of the fluorescent or scattered peaks. XRR profiles of carrageenan thin films yielded a mean value for the critical angle close to quartz substrate. Thickness measurements of the prepared carrageenan thin films showed that concentration was the main determinant for final film thickness over the other process parameters. Sulfur fluorescent intensity derived from the TXRF measurement showed a linear relationship with the measured thickness by XRR. For PVP, measured critical angle is lower than quartz. Poor adhesion of the polymer onto the substrate yielded a limited number of thickness measurements made from the XRR profiles. (Author)

Analog modeling of splitting the envelope of an electromagnetic pulse reflected from a plasma layer

International Nuclear Information System (INIS)

Bakunov, M.I.; Rogozhin, I.Yu.

1997-01-01

By means of a simple radio engineering model, an experimental study is carried out of the effect of the strong deformation of the envelope of a quasimonochromatic electromagnetic pulse reflected from a thin plasma layer placed on the surface of an ideal conductor. This deformation is considered under the conditions of the plasma resonance in the plasma layer and when the thickness of the layer is less then the wavelength of the incident radiation. It is shown that the pulse whose initial profile is Gaussian, after the reflection, is separated (entirely of partially) into two pulses with amplitudes that can be controlled by means of varying the parameters of the incident pulse and plasma layer

Late effects of selected immunosuppressants on immunocompetence, disease incidence, and mean life-span. III. Disease incidence and life expectancy. [Mice, x radiation

Energy Technology Data Exchange (ETDEWEB)

Peter, C P; Perkins, E H; Peterson, W J; Walburg, H E; Makinodan, T

1975-01-01

The effect of various immunosuppressive treatments on mean life-span and disease incidence have been studied. Significant life shortening was seen only in mice which received X-irradiation early in life and can be ascribed primarily to an increased incidence of certain malignancies. Marginal life shortening was seen in cyclophosphamide-treated animals, however, survival patterns between those and control animals did not differ until 30 months of age and the magnitude of life-shortening never approached that seen in X-irradiated animals. Thymectomy, splenectomy or cortisone treatment did not alter survival. All immunosuppressive treatments enhanced mortality due to non-neoplastic diseases, however, only a small percentage of animals die with these disease entities. With the exception of cortisone all immunosuppressive treatments increased the incidence of neoplastic disease. However, their effects on various neoplastic processes were variable and unpredictable. Four primary patterns in terms of relative immune competence, disease incidence and life expectancy were seen. Thus, immunodepression may or may not correlate with increased disease incidence, which in turn may or may not have a life-shortening effect. These findings are discussed in terms of the marked reduction of both humoral and cell-mediated immunity normally seen in aged mice and the significance of postulated immune surveillance mechanisms to survival.

Measurement of the spatial resolution of wide-pitch silicon strip detectors with large incident angle

International Nuclear Information System (INIS)

Kawasaki, T.; Hazumi, M.; Nagashima, Y.

1996-01-01

As a part of R ampersand D for the BELLE experiment at KEK-B, we measured the spatial resolution of silicon strip detectors for particles with incident angles ranging from 0 degrees to 75 degrees. These detectors have strips with pitches of 50, 125 and 250 μm on the ohmic side. We have obtained the incident angle dependence which agreed well with a Monte Carlo simulation. The resolution was found to be 11 μm for normal incidence with a pitch of 50 μm, and 29 μm for incident angle of 75 degrees with a pitch of 250μm

X-ray reflectivity study of bias graded diamond like carbon film ...

Indian Academy of Sciences (India)

destructive technique for determining layer thickness, sur- face and interfacial roughness and internal structure of films. The XRR technique is alike the optical reflectivity technique and is performed at a glancing angle. ..... critical incident energy window the film attains minimum roughness. Thereafter, for higher energy the ...

Bladder cancer mapping in Libya based on standardized morbidity ratio and log-normal model

Science.gov (United States)

Alhdiri, Maryam Ahmed; Samat, Nor Azah; Mohamed, Zulkifley

2017-05-01

Disease mapping contains a set of statistical techniques that detail maps of rates based on estimated mortality, morbidity, and prevalence. A traditional approach to measure the relative risk of the disease is called Standardized Morbidity Ratio (SMR). It is the ratio of an observed and expected number of accounts in an area, which has the greatest uncertainty if the disease is rare or if geographical area is small. Therefore, Bayesian models or statistical smoothing based on Log-normal model are introduced which might solve SMR problem. This study estimates the relative risk for bladder cancer incidence in Libya from 2006 to 2007 based on the SMR and log-normal model, which were fitted to data using WinBUGS software. This study starts with a brief review of these models, starting with the SMR method and followed by the log-normal model, which is then applied to bladder cancer incidence in Libya. All results are compared using maps and tables. The study concludes that the log-normal model gives better relative risk estimates compared to the classical method. The log-normal model has can overcome the SMR problem when there is no observed bladder cancer in an area.

Complex refractive index measurements for BaF 2 and CaF 2 via single-angle infrared reflectance spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Kelly-Gorham, Molly Rose K.; DeVetter, Brent M.; Brauer, Carolyn S.; Cannon, Bret D.; Burton, Sarah D.; Bliss, Mary; Johnson, Timothy J.; Myers, Tanya L.

2017-10-01

We have re-investigated the optical constants n and k for the homologous series of inorganic salts barium fluoride (BaF2) and calcium fluoride (CaF2) using a single-angle near-normal incidence reflectance device in combination with a calibrated Fourier transform infrared (FTIR) spectrometer. Our results are in good qualitative agreement with most previous works. However, certain features of the previously published data near the reststrahlen band exhibit distinct differences in spectral characteristics. Notably, our measurements of BaF2 do not include a spectral feature in the ~250 cm-1 reststrahlen band that was previously published. Additionally, CaF2 exhibits a distinct wavelength shift relative to the model derived from previously published data. We confirmed our results with recently published works that use significantly more modern instrumentation and data reduction techniques

Global trends in testicular cancer incidence and mortality.

Science.gov (United States)

Rosen, Alexandre; Jayram, Gautam; Drazer, Michael; Eggener, Scott E

2011-08-01

Epidemiologic studies on testicular cancer have focused primarily on European countries. Global incidence and mortality have been less thoroughly evaluated. Our goal was to gain a better understanding of the most recent global age-standardized incidence and mortality rates for testicular cancer and to use these values to estimate a region's health care quality. Age-standardized incidence rate (ASIR) and age-standardized mortality rate (ASMR) for testicular cancer were obtained for men of all ages in 172 countries by using the GLOBOCAN 2008 database, reflecting the annual rate of cancer incidence and mortality per 100,000 men. These data were evaluated on a regional level to compare incidence and mortality rates. Global plots of these values were constructed to better visualize geographic distributions. Finally, the ratio of ASIR to ASMR was calculated as a method to assess each region's proficiency in diagnosing and effectively treating testicular cancer. ASIR and ASMR were analyzed by region, and each region's ratio of ASIR to ASMR was calculated. Testicular cancer ASIR is highest in Western Europe (7.8%), Northern Europe (6.7%), and Australia (6.5%). Asia and Africa had the lowest incidence (ASMR was highest in Central America (0.7%), western Asia (0.6%), and Central and Eastern Europe (0.6%). Mortality was lowest in North America, Northern Europe, and Australia (0.1-0.2%). The ASIR-ASMR ratio was highest in Australia (65.0%) and lowest in western Africa (1.0%). National reporting systems varied by country, and data quality may have fluctuated between regions. Testicular cancer incidence remains highest in developed nations with primarily Caucasian populations. Variable ASIR-ASMR ratios suggest markedly different geographic-specific reporting mechanisms, access to care, and treatment capabilities. Copyright © 2011 European Association of Urology. Published by Elsevier B.V. All rights reserved.

IMPLEMENTATION OF INCIDENT DETECTION ALGORITHM BASED ON FUZZY LOGIC IN PTV VISSIM

Directory of Open Access Journals (Sweden)

Andrey Borisovich Nikolaev

2017-05-01

Full Text Available Traffic incident management is a major challenge in the management of movement, requiring constant attention and significant investment, as well as fast and accurate solutions in order to re-establish normal traffic conditions. Automatic control methods are becoming an important factor for the reduction of traffic congestion caused by an arising incident. In this paper, the algorithm of automatic detection incident based on fuzzy logic is implemented in the software PTV VISSIM. 9 different types of tests were conducted on the two lane road section segment with changing traffic conditions: the location of the road accident, loading of traffic. The main conclusion of the research is that the proposed algorithm for the incidents detection demonstrates good performance in the time of detection and false alarms

MHD Wave Propagation at the Interface Between Solar Chromosphere and Corona

Science.gov (United States)

Huang, Y.; Song, P.; Vasyliunas, V. M.

2017-12-01

We study the electromagnetic and momentum constraints at the solar transition region which is a sharp layer interfacing between the solar chromosphere and corona. When mass transfer between the two domains is neglected, the transition region can be treated as a contact discontinuity across which the magnetic flux is conserved and the total forces are balanced. We consider an Alfvénic perturbation that propagates along the magnetic field incident onto the interface from one side. In order to satisfy the boundary conditions at the transition region, only part of the incident energy flux is transmitted through and the rest is reflected. Taking into account the highly anisotropic propagation of waves in magnetized plasmas, we generalize the law of reflection and specify Snell's law for each of the three wave MHD modes: incompressible Alfvén mode and compressible fast and slow modes. Unlike conventional optical systems, the interface between two magnetized plasmas is not rigid but can be deformed by the waves, allowing momentum and energy to be transferred by compression. With compressible modes included, the Fresnel conditions need substantial modification. We derive Fresnel conditions, reflectivities and transmittances, and mode conversion for incident waves propagating along the background magnetic field. The results are well organized when the incident perturbation is decomposed into components in and normal to the incident plane (containing the background magnetic field and the normal direction of the interface). For a perturbation normal to the incident plane, both transmitted and reflected perturbations are incompressible Alfvén mode waves. For a perturbation in the incident plane, they can be compressible slow and fast mode waves which may produce ripples on the transition region.

X-ray reflectivity and surface roughness

International Nuclear Information System (INIS)

Ocko, B.M.

1988-01-01

Since the advent of high brightness synchrotron radiation sources there has been a phenomenal growth in the use of x-rays as a probe of surface structure. The technique of x-ray reflectivity is particularly relevant to electrochemists since it is capable of probing the structure normal to an electrode surface in situ. In this paper the theoretical framework for x-ray reflectivity is reviewed and the results from previous non-electrochemistry measurements are summarized. These measurements are from the liquid/air interface (CCl 4 ), the metal crystal vacuum interface (Au(100)), and from the liquid/solid interface(liquid crystal/silicon). 34 refs., 5 figs

Nonlocal Andreev reflection and spin current in a three-terminal Aharonov–Bohm interferometer

International Nuclear Information System (INIS)

Ju, Peng; Hua-Ling, Yu; Zhi-Guo, Wang

2009-01-01

This paper theoretically reports the nonlocal Andreev reflection and spin current in a normal metal-ferromagnetic metal-superconducting Aharonov–Bohm interferometer. It is found that the electronic current and spin current are sensitive to systematic parameters, such as the gate voltage of quantum dots and the external magnetic flux. The electronic current in the normal metal lead results from two competing processes: quasiparticle transmission and nonlocal Andreev reflection. The appearance of zero spin-up electronic current (or spin-down electronic current) signals the existence of nonlocal Andreev reflection, and the presence of zero electronic current results in the appearance of pure spin current. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Out-of-plane reflection and refraction of light by anisotropic optical antenna metasurfaces with phase discontinuities.

Science.gov (United States)

Aieta, Francesco; Genevet, Patrice; Yu, Nanfang; Kats, Mikhail A; Gaburro, Zeno; Capasso, Federico

2012-03-14

Experiments on ultrathin anisotropic arrays of subwavelength optical antennas display out-of-plane refraction. A powerful three-dimensional (3D) extension of the recently demonstrated generalized laws of refraction and reflection shows that the interface imparts a tangential wavevector to the incident light leading to anomalous beams, which in general are noncoplanar with the incident beam. The refracted beam direction can be controlled by varying the angle between the plane of incidence and the antenna array. © 2012 American Chemical Society

Pathologic evaluation of normal and perfused term placental tissue

DEFF Research Database (Denmark)

Maroun, Lisa Leth; Mathiesen, Line; Hedegaard, Morten

2014-01-01

This study reports for the 1st time the incidence and interobserver variation of morphologic findings in a series of 34 term placentas from pregnancies with normal outcome used for perfusion studies. Histologic evaluation of placental tissue is challenging, especially when it comes to defining...... "normal tissue" versus "pathologic lesions." A scoring system for registration of abnormal morphologic findings was developed. Light microscopic examination was performed independently by 2 pathologists, and interobserver variation was analyzed. Findings in normal and perfused tissue were compared...... and selected findings were tested against success parameters from the perfusions. Finally, the criteria for frequent lesions with fair to poor interobserver variation in the nonperfused tissue were revised and reanalyzed. In the perfused tissue, the perfusion artefact "trophoblastic vacuolization," which...

Medication incidents reported to an online incident reporting system.

LENUS (Irish Health Repository)

Alrwisan, Adel

2011-01-15

AIMS: Approximately 20% of deaths from adverse events are related to medication incidents, costing the NHS an additional £500 million annually. Less than 5% of adverse events are reported. This study aims to assess the reporting rate of medication incidents in NHS facilities in the north east of Scotland, and to describe the types and outcomes of reported incidents among different services. Furthermore, we wished to quantify the proportion of reported incidents according to the reporters\\' profession. METHODS: A retrospective description was made of medication incidents reported to an online reporting system (DATIX) over a 46-month-period (July 2005 to April 2009). Reports originated from acute and community hospitals, mental health, and primary care facilities. RESULTS: Over the study period there were 2,666 incidents reported with a mean monthly reporting rate of 78.2\\/month (SD±16.9). 6.1% of all incidents resulted in harm, with insulin being the most commonly implicated medication. Nearly three-quarters (74.2%, n=1,978) of total incidents originated from acute hospitals. Administration incidents were implicated in the majority of the reported medication incidents (59%), followed by prescribing (10.8%) and dispensing (9.9%), while the nondescript "other medication incidents" accounted for 20.3% of total incidents. The majority of reports were made by nursing and midwifery staff (80%), with medical and dental professionals reporting the lowest number of incidents (n=56, 2%). CONCLUSIONS: The majority of medication incidents in this study were reported by nursing and midwifery staff, and were due to administration incidents. There is a clear need to elucidate the reasons for the limited contribution of the medical and dental professionals to reporting medication incidents.

Improvement of Infrared Detectors for Tissue Oximetry using Black Silicon Nanostructures

DEFF Research Database (Denmark)

Petersen, Søren Dahl; Davidsen, Rasmus Schmidt; Alcala, Lucia R.

2014-01-01

We present a nanostructured surface, made of dry etched black silicon, which lowers the reflectance for light incident at all angles. This surface is fabricated on infrared detectors used for tissue oximetry, where the detection of weak diffuse light signals is important. Monte Carlo simulations...... performed on a model of a neonatal head shows that approximately 60% of the injected light will be diffuse reflected. However, the change in diffuse reflected light due to the change in cerebral oxygenation is very low and the light will be completely isotropic scattered. The reflectance of the black...... in quantum efficiency for both normal incident light and light incident at 38°....

[Reference ranges of gestational weight gain in Chinese population on the incidence of macrosomia: a multi-center cross-sectional survey].

Science.gov (United States)

Liang, H; Zhang, W Y; Li, X T

2017-03-25

Objective: To investigate the influence of gestational weight gain (GWG) on the incidence of macrosomia, and to establish the reference ranges of GWG based on the incidence of macrosomia. Methods: A multicenter, cross-sectional study was conducted. Totally, 112 485 women were recruited from 39 hospitals in 14 provinces in China. Totally, 61 149 cases were eligible with singleton pregnancies and non-premature deliveries. The associations of pre-pregnancy body mass index (BMI), GWG, newborn gender and gestational diabetes with macrosomia were analyzed with logistic regression. The normal GWG ranges were calculated in all maternal BMI subgroups, based on the normal incidence of macrosomia was set as the range of 5.0% to 10.0%. Results: In this study, the incidence of macrosomia was 7.46% (4 563/611 149). The macrosociam was positive related with maternal height, delivery week, pre-pregnancy BMI, GWG, gestational diabetes, primipara, and male babies significantly ( P< 0.05), based on unadjusted and adjusted logestic regression. The normal range of GWG 20.0-25.0, 10.0-20.0, 0-10.0 and 0-5.0 kg in subgroups of underweight (pre-pregnancy BMI<18.5 kg/m(2)), normal (18.5-24.9 kg/m(2)), overweight (25.0-29.9 kg/m(2)) and obese (≥30.0 kg/m(2)), respectively. Conclusion: The reference range of GWG in China based on the incidence of macrosomia is established.

Theory of the Andreev reflection and the density of states in proximity contact normal-superconducting infinite double-layer

International Nuclear Information System (INIS)

Nagato, Yasushi; Nagai, Katsuhiko

1993-01-01

Proximity contact N-S double-layer with infinite layer widths is studied in the clean limit. The finite reflection at the interface is taken into account. Starting from a recent theory of finite width double-layer by Ashida et al., the authors obtain explicit expressions for the quasi-classical Green's function which already satisfy the boundary condition and include no exploding terms at infinities. The self-consistent pair potentials are obtained numerically with sufficient accuracy. The Andreev reflection at the N-S interface is discussed on the basis of the self-consistent pair potential. It is shown that there exists a resonance state in a potential valley formed between the depressed pair potential and the partially reflecting interface, which leads to a peak of the Andreev reflection coefficient with the height unity slightly below the bulk superconductor energy gap. They also find general relationship between the Andreev reflection coefficient and the local density of states of the superconductor just at the interface

Semi-automated high-efficiency reflectivity chamber for vacuum UV measurements

Science.gov (United States)

Wiley, James; Fleming, Brian; Renninger, Nicholas; Egan, Arika

2017-08-01

This paper presents the design and theory of operation for a semi-automated reflectivity chamber for ultraviolet optimized optics. A graphical user interface designed in LabVIEW controls the stages, interfaces with the detector system, takes semi-autonomous measurements, and monitors the system in case of error. Samples and an optical photodiode sit on an optics plate mounted to a rotation stage in the middle of the vacuum chamber. The optics plate rotates the samples and diode between an incident and reflected position to measure the absolute reflectivity of the samples at wavelengths limited by the monochromator operational bandpass of 70 nm to 550 nm. A collimating parabolic mirror on a fine steering tip-tilt motor enables beam steering for detector peak-ups. This chamber is designed to take measurements rapidly and with minimal oversight, increasing lab efficiency for high cadence and high accuracy vacuum UV reflectivity measurements.

Electrically Tunable Reflective Terahertz Phase Shifter Based on Liquid Crystal

Science.gov (United States)

Yang, Jun; Xia, Tianyu; Jing, Shuaicheng; Deng, Guangsheng; Lu, Hongbo; Fang, Yong; Yin, Zhiping

2018-02-01

We present a reflective spatial phase shifter which operates at terahertz regime above 325 GHz. The controllable permittivity of the nematic liquid crystals was utilized to realize a tunable terahertz (THz) reflective phase shifter. The reflective characteristics of the terahertz electromagnetic waves and the liquid crystal parameters were calculated and analyzed. We provide the simulation results for the effect of the incident angle of the plane wave on the reflection. The experiment was carried out considering an array consisting of 30 × 30 patch elements, printed on a 20 × 20 mm quartz substrate with 1-mm thickness. The phase shifter provides a tunable phase range of 300° over the frequency range of 325 to 337.6 GHz. The maximum phase shift of 331° is achieved at 330 GHz. The proposed phase shifter is a potential candidate for THz applications, particularly for reconfigurable reflectarrays.

Relating normalization to neuronal populations across cortical areas.

Science.gov (United States)

Ruff, Douglas A; Alberts, Joshua J; Cohen, Marlene R

2016-09-01

Normalization, which divisively scales neuronal responses to multiple stimuli, is thought to underlie many sensory, motor, and cognitive processes. In every study where it has been investigated, neurons measured in the same brain area under identical conditions exhibit a range of normalization, ranging from suppression by nonpreferred stimuli (strong normalization) to additive responses to combinations of stimuli (no normalization). Normalization has been hypothesized to arise from interactions between neuronal populations, either in the same or different brain areas, but current models of normalization are not mechanistic and focus on trial-averaged responses. To gain insight into the mechanisms underlying normalization, we examined interactions between neurons that exhibit different degrees of normalization. We recorded from multiple neurons in three cortical areas while rhesus monkeys viewed superimposed drifting gratings. We found that neurons showing strong normalization shared less trial-to-trial variability with other neurons in the same cortical area and more variability with neurons in other cortical areas than did units with weak normalization. Furthermore, the cortical organization of normalization was not random: neurons recorded on nearby electrodes tended to exhibit similar amounts of normalization. Together, our results suggest that normalization reflects a neuron's role in its local network and that modulatory factors like normalization share the topographic organization typical of sensory tuning properties. Copyright © 2016 the American Physiological Society.

Enface Thickness Mapping and Reflectance Imaging of Retinal Layers in Diabetic Retinopathy.

Science.gov (United States)

Francis, Andrew W; Wanek, Justin; Lim, Jennifer I; Shahidi, Mahnaz

2015-01-01

To present a method for image segmentation and generation of enface thickness maps and reflectance images of retinal layers in healthy and diabetic retinopathy (DR) subjects. High density spectral domain optical coherence tomography (SDOCT) images were acquired in 10 healthy and 4 DR subjects. Customized image analysis software identified 5 retinal cell layer interfaces and generated thickness maps and reflectance images of the total retina (TR), inner retina (IR), outer retina (OR), and the inner segment ellipsoid (ISe) band. Thickness maps in DR subjects were compared to those of healthy subjects by generating deviation maps which displayed retinal locations with thickness below, within, and above the normal 95% confidence interval. In healthy subjects, TR and IR thickness maps displayed the foveal depression and increased thickness in the parafoveal region. OR and ISe thickness maps showed increased thickness at the fovea, consistent with normal retinal anatomy. In DR subjects, thickening and thinning in localized regions were demonstrated on TR, IR, OR, and ISe thickness maps, corresponding to retinal edema and atrophy, respectively. TR and OR reflectance images showed reduced reflectivity in regions of increased thickness. Hard exudates appeared as hyper-reflective spots in IR reflectance images and casted shadows on the deeper OR and ISe reflectance images. The ISe reflectance image clearly showed the presence of focal laser scars. Enface thickness mapping and reflectance imaging of retinal layers is a potentially useful method for quantifying the spatial and axial extent of pathologies due to DR.

Nonlinear reflection of shock shear waves in soft elastic media.

Science.gov (United States)

Pinton, Gianmarco; Coulouvrat, François; Gennisson, Jean-Luc; Tanter, Mickaël

2010-02-01

For fluids, the theoretical investigation of shock wave reflection has a good agreement with experiments when the incident shock Mach number is large. But when it is small, theory predicts that Mach reflections are physically unrealistic, which contradicts experimental evidence. This von Neumann paradox is investigated for shear shock waves in soft elastic solids with theory and simulations. The nonlinear elastic wave equation is approximated by a paraxial wave equation with a cubic nonlinear term. This equation is solved numerically with finite differences and the Godunov scheme. Three reflection regimes are observed. Theory is developed for shock propagation by applying the Rankine-Hugoniot relations and entropic constraints. A characteristic parameter relating diffraction and non-linearity is introduced and its theoretical values are shown to match numerical observations. The numerical solution is then applied to von Neumann reflection, where curved reflected and Mach shocks are observed. Finally, the case of weak von Neumann reflection, where there is no reflected shock, is examined. The smooth but non-monotonic transition between these three reflection regimes, from linear Snell-Descartes to perfect grazing case, provides a solution to the acoustical von Neumann paradox for the shear wave equation. This transition is similar to the quadratic non-linearity in fluids.

Packing stress reduction in polymer-lipid monolayers at the air-water interface: An X-ray grazing-incidence diffraction and reflectivity study

Energy Technology Data Exchange (ETDEWEB)

Kuhl, T.L.; Majewski, J.; Howes, P.B.; Kjaer, K.; Nahmen, A. von; Lee, K.Y.C.; Ocko, B.; Israelachvili, J.N.; Smith, G.S.

1999-08-25

Using synchrotron grazing-incidence X-ray diffraction (GIXD) and reflectivity (XR), the authors have determined the in-plane and out-of-plane structure of phospholipid monolayers at the air-water interface as a function of hydrophilic lipid headgroup size. Di-stearoyl-phosphatidyl-ethanolamine (DSPE) lipid monolayers were systematically modified by chemically grafting hydrophilic poly(ethylene glycol) (PEG) chains of MW = 90 g/mol (2 ethylene oxide, EO, units), MW = 350 g/mol (8 EO units), and MW = 750 g/mol (17 EO units) to the lipid headgroups. The monolayers were studied in the solid phase at a surface pressure of 42 mN/m. At these high lipid packing densities, the PEG chains are submerged in the water subphase. The increased packing stresses from these bulky polymer headgroups distort the unit cell and the in-plane packing modes of the monolayers, leading to large out-of-plane alterations and staggering of the lipid molecules. Surprisingly, a change in the molecular packing of the monolayer toward higher packing densities (lower area per molecule) was observed on increasing the PEG MW to 750 g/mol (17 EO units). This rearrangement of the monolayer structure may be due to a conformational change in the PEG chains.

Direct observation of ballistic Andreev reflection

Science.gov (United States)

Klapwijk, T. M.; Ryabchun, S. A.

2014-12-01

An overview is presented of experiments on ballistic electrical transport in inhomogeneous superconducting systems which are controlled by the process of Andreev reflection. The initial experiments based on the coexistence of a normal phase and a superconducting phase in the intermediate state led to the concept itself. It was followed by a focus on geometrically inhomogeneous systems like point contacts, which provided a very clear manifestation of the energy and direction dependence of the Andreev reflection process. The point contacts have recently evolved towards the atomic scale owing to the use of mechanical break-junctions, revealing a very detailed dependence of Andreev reflection on the macroscopic phase of the superconducting state. In present-day research, the superconducting in homogeneity is constructed by clean room technology and combines superconducting materials, for example, with low-dimensional materials and topological insulators. Alternatively, the superconductor is combined with nano-objects, such as graphene, carbon nanotubes, or semiconducting nanowires. Each of these "inhomogeneous systems" provides a very interesting range of properties, all rooted in some manifestation of Andreev reflection.

Statin Use, Incident Dementia and Alzheimer Disease in Elderly African Americans.

Science.gov (United States)

Hendrie, Hugh C; Hake, Ann; Lane, Kathleen; Purnell, Christianna; Unverzagt, Frederick; Smith-Gamble, Valerie; Murrell, Jill; Ogunniyi, Adesola; Baiyewu, Olusegun; Callahan, Chris; Saykin, Andrew; Taylor, Stanley; Hall, Kathleen; Gao, Su

2015-08-07

To investigate the association between statin use, incident dementia, and Alzheimer disease (AD) in a prospective elderly African American cohort. Two stage design with a screening interview followed by a comprehensive in-home assessment conducted over an eight-year period. Diagnoses of incident AD and dementia were made by consensus. Statin use was collected at each evaluation. Measurements of low-density lipoprotein cholesterol (LDL), C-reactive protein (CRP) and APOE genotype were obtained from baseline blood samples. Logistic regression models were used to test the association of statin use on incident dementia and AD and its possible association with lipid and CRP levels. Indianapolis, Indiana. From an original cohort of 2629 participants, a subsample of 974 African Americans aged >70 years with normal cognition, at least one follow up evaluation, complete statin information, and biomarker availability were included. Incident dementia and incident AD. After controlling for age at diagnosis, sex, education level, presence of the APOE ε4 allele and history of stroke for the incident dementia model, baseline use of statins was associated with a significantly decreased risk of incident dementia (OR=.44, P=.029) and incident AD (OR=.40, P=.029). The significant effect of statin use on reduced AD risk and trend for dementia risk was found only for those participants who reported consistent use over the observational period (incident AD: P=.034; incident dementia: P=.061). Additional models found no significant interaction between baseline statin use, baseline LDL, or CRP level and incident dementia/AD. Consistent use of statin medications during eight years of follow-up resulted in significantly reduced risk for incident AD and a trend toward reduced risk for incident dementia.

Acoustic plane waves normally incident on a clamped panel in a rectangular duct. [to explain noise reduction curves for reducing interior noise in aircraft

Science.gov (United States)

Unz, H.; Roskam, J.

1979-01-01

The theory of acoustic plane wave normally incident on a clamped panel in a rectangular duct is developed. The coupling theory between the elastic vibrations of the panel (plate) and the acoustic wave propagation in infinite space and in the rectangular duct is considered. The partial differential equation which governs the vibration of the panel (plate) is modified by adding to its stiffness (spring) forces and damping forces, and the fundamental resonance frequency and the attenuation factor are discussed. The noise reduction expression based on the theory is found to agree well with the corresponding experimental data of a sample aluminum panel in the mass controlled region, the damping controlled region, and the stiffness controlled region. All the frequency positions of the upward and downward resonance spikes in the sample experimental data are identified theoretically as resulting from four cross interacting major resonance phenomena: the cavity resonance, the acoustic resonance, the plate resonance, and the wooden back panel resonance.

Near IR Scanning Angle Total Internal Reflection Raman Spectroscopy at Smooth Gold Films

Energy Technology Data Exchange (ETDEWEB)

McKee, Kristopher; Meyer, Matthew; Smith, Emily

2012-04-13

Total internal reflection (TIR) Raman and reflectivity spectra were collected for nonresonant analytes as a function of incident angle at sapphire or sapphire/smooth 50 nm gold interfaces using 785 nm excitation. For both interfaces, the Raman signal as a function of incident angle is well-modeled by the calculated interfacial mean square electric field (MSEF) relative to the incident field times the thickness of the layer being probed in the Raman measurement (D{sub RS}). The Raman scatter was reproducibly enhanced at the interface containing a gold film relative to the sapphire interface by a factor of 4.3–4.6 for aqueous pyridine or 2.2–3.7 for neat nitrobenzene, depending on the analyzed vibrational mode. The mechanism for the increased Raman signal is the enhanced MSEF at incident angles where propagating surface plasmons are excited in the metal film. The background from the TIR prism was reduced by 89–95% with the addition of the gold film, and the percent relative uncertainty in peak area was reduced from 15 to 1.7% for the 1347 cm–1 mode of nitrobenzene. Single monolayers of benzenethiol (S/N = 6.8) and 4-mercaptopyridine (S/N = 16.5) on gold films were measured by TIR Raman spectroscopy with 785 nm excitation (210 mW) without resonant enhancement in 1 min.

Angularly symmetric splitting of a light beam upon reflection and refraction at an air-dielectric plane boundary: comment.

Science.gov (United States)

Andersen, Torben B

2016-05-01

In a recent paper, conditions for achieving equal and opposite angular deflections of a light beam by reflection and refraction at an interface between air and a dielectric were determined [J. Opt. Soc. Am. A32, 2436 (2015)JOAOD60740-323210.1364/JOSAA.32.002436]. The paper gives plots of angles of incidence and refraction as a function of the prism refractive index as well as plots of reflectances and incident linear-polarization azimuth angles as functions of the refractive index. We show here that it is possible to express these quantities as simple algebraic functions of the refractive index.

Far-infrared reflection-absorption spectroscopy of amorphous and polycrystalline gallium arsenide films

International Nuclear Information System (INIS)

Gregory, J.R.

1992-01-01

We have reported far-infrared reflection absorption spectra (30-320CM -1 ) at 30 and 310K for nine films of non-stoichiometric GaAs. The FIRRAS measurements were performed using the grazing incidence FIR double-modulation spectroscopy technique first described by DaCosta and Coleman. The films were fabricated by molecular beam deposition on metallized substrates for two As/Ga molecular beam flux ratios. The films were characterized by depth profilometry, IRAS, XRD, and x-ray microprobe analysis. Film thicknesses ranged from 800 to 5800 angstrom and compositions were 45-50% As for a MB flux ratio of 0.29 and 60-70% As for a ratio of 1.12. FIRRAS measurements were made and characterizations performed for as-deposited films and for 5 hour anneals at 473, 573, 673 and 723 degrees C. Vibrational spectra of the crystallized films were interpreted in terms of the exact reflectivity of a thin dielectric film on a conducting substrate, using a classical Lorentzian dielectric function for the response of the film. Resonances appearing in the open-quote forbidden close-quote region between the TO and LO frequencies were modelled with an effective medium approximation and are interpreted as arising from small-scale surface roughness. The behavior of the amorphous film spectra were examined within two models. The effective force constant model describes the variation of the reflection-absorption maxima with measured crystallite size in terms of the effective vibration frequency of 1-D atomic chains having force constants distributed according to the parameters of the crystalline-to-amorphous relaxation length and the crystalline to amorphous force constant ratio. The dielectric function continuum model uses the relaxation of the crystal momentum selection rule to calculate the reflection-absorption spectrum based on a dielectric function in which the oscillator strength is the normalized product of a constant dipole strength and the smoothed vibrational density of states

Estimated HIV incidence in the United States, 2006-2009.

Directory of Open Access Journals (Sweden)

Joseph Prejean

Full Text Available BACKGROUND: The estimated number of new HIV infections in the United States reflects the leading edge of the epidemic. Previously, CDC estimated HIV incidence in the United States in 2006 as 56,300 (95% CI: 48,200-64,500. We updated the 2006 estimate and calculated incidence for 2007-2009 using improved methodology. METHODOLOGY: We estimated incidence using incidence surveillance data from 16 states and 2 cities and a modification of our previously described stratified extrapolation method based on a sample survey approach with multiple imputation, stratification, and extrapolation to account for missing data and heterogeneity of HIV testing behavior among population groups. PRINCIPAL FINDINGS: Estimated HIV incidence among persons aged 13 years and older was 48,600 (95% CI: 42,400-54,700 in 2006, 56,000 (95% CI: 49,100-62,900 in 2007, 47,800 (95% CI: 41,800-53,800 in 2008 and 48,100 (95% CI: 42,200-54,000 in 2009. From 2006 to 2009 incidence did not change significantly overall or among specific race/ethnicity or risk groups. However, there was a 21% (95% CI:1.9%-39.8%; p = 0.017 increase in incidence for people aged 13-29 years, driven by a 34% (95% CI: 8.4%-60.4% increase in young men who have sex with men (MSM. There was a 48% increase among young black/African American MSM (12.3%-83.0%; p<0.001. Among people aged 13-29, only MSM experienced significant increases in incidence, and among 13-29 year-old MSM, incidence increased significantly among young, black/African American MSM. In 2009, MSM accounted for 61% of new infections, heterosexual contact 27%, injection drug use (IDU 9%, and MSM/IDU 3%. CONCLUSIONS/SIGNIFICANCE: Overall, HIV incidence in the United States was relatively stable 2006-2009; however, among young MSM, particularly black/African American MSM, incidence increased. HIV continues to be a major public health burden, disproportionately affecting several populations in the United States, especially MSM and racial and

Survey of reportable incidents in nuclear power plants in Germany in the year 1992

International Nuclear Information System (INIS)

1993-01-01

In 1992, 223 reportable incidents in German nuclear power plant have been reported. There was no radioactivity release exceeding the maximum permissible limits, and there were no hazardous effects on the population or the environment. There was no incident belonging to category S of the official event scale, requiring urgent notification, while there were two incidents requiring immediate notification. All other incidents reported belonged to category N, the lowest on the scale, requiring normal notification. 216 incidents belonged to category 0 of the INES scale, and 7 to INES category 1 (disturbance). The tabulated survey of the report lists the various events and their position on the INES scale. The reportable events have been analysed thoroughly from various viewpoints, but no systematic pattern of weak points could be detected. (orig./HP) [de

On the reflectivity of nickel neutron mirrors

Energy Technology Data Exchange (ETDEWEB)

Adib, M.; Maayouf, R.M.A.; Abdel-Kawy, A.; Habib, N. (Atomic Energy Establishment, Cairo (Egypt). Reactor and Neutron Physics Dept.); Kenawy, M.A.; Wahba, M.; Ashry, A.H. (Ain Shams Univ., Cairo (Egypt))

1991-02-01

Neutron reflectivities were determined for 300 nm thick films of natural nickel and nickel 58 coated on glass plates. The measurements were performed at glancing angles between 40' and 60'. The incident neutron beam from one of the ET-RR-1 reactor horizontal channels covered neutron wavelengths between 0.55 and 0.80 nm. It was found that nickel 58, because of the high value of its critical glancing angle, is more efficient as a neutron mirror than natural nickel. (orig.).

Reflection and Refraction of Light in Absorbing Media

Science.gov (United States)

Katsumata, Koichi; Sasaki, Shosuke

2018-05-01

The results of a rigorous calculation of optical phenomena in absorbing media based on Maxwell's equations are reported. In the case of an absorbing dielectric, we assume a complex dielectric constant. We find an expression for the angle of refraction as a function of the incident angle and the real and imaginary parts of the complex dielectric constant, all of which are real. The amplitudes of the reflected and transmitted waves are calculated on the same footing. These amplitudes are shown to be complex, from which we deduce the magnitude and phase change of the reflection and transmission coefficients. The same argument applies to an absorbing magnetic material if we replace the complex dielectric constant by a complex magnetic permeability.

Reflectivity and energy balance in pulsed-laser deposition experiments from mono- and bi-atomic targets

International Nuclear Information System (INIS)

Mueller, T.; Rohr, K.P.; Sinha, B. K.

2002-01-01

Reflectivity and complete energy balance from the planar targets of aluminum, copper, nickel, and molybdenum have been measured using a Nd: glass laser (λ=1060 nm,τ=5 ns) in the low intensity regime of laser plasma interaction as a function of focal spot size. The magnitude of partition of total incident laser energy into different channels is observed to decrease as the focal spot size increases. It is further observed that the magnitude of partition of the incident energy into these channels, in general, decreases as the atomic number increases for any given focal spot size, although, the reflectivity component of the partitioned energy increases with focal spot size for any given element. The reflectivities of copper and tungsten and their alloy were measured separately. The reflectivity from the alloy plasma was reduced by a factor of 6 compared to either element separately. This observation confirms the recent theory that in the multiion plasma the ion acoustic waves are additionally damped due to additional Joule, thermal diffusion, and viscous terms in the modified ion-fluid theory of the ion acoustic waves in a multiion species plasma

Statement of nuclear incidents at nuclear installations. Third quarter 2001

International Nuclear Information System (INIS)

2002-01-01

A statement of nuclear incidents at nuclear installations in Britain during the third quarter of 2001 is published today by the Health and Safety Executive (copy attached). It covers the period 1 July to 30 September 2001. The statement is published under arrangements that came into effect from the first quarter of 1993, derived from the Health and Safety Commission's powers under section 11 of the Health and Safety at Work, etc. Act 1974. Normally each incident mentioned in HSE's Quarterly Incident Statements will already have been made public by the licensee or site operator either through a press statement or by inclusion in the newsletter for the site concerned. The locations of the installations mentioned in the statement are as follows: Heysham 1 (British Energy Generation plc), Sellafield (British Nuclear Fuels plc), Chapelcross (British Nuclear Fuels plc)

Elastic reflection based waveform inversion with a nonlinear approach

KAUST Repository

Guo, Qiang

2017-08-16

Full waveform inversion (FWI) is a highly nonlinear problem due to the complex reflectivity of the Earth, and this nonlinearity only increases under the more expensive elastic assumption. In elastic media, we need a good initial P-wave velocity and even a better initial S-wave velocity models with accurate representation of the low model wavenumbers for FWI to converge. However, inverting for the low wavenumber components of P- and S-wave velocities using reflection waveform inversion (RWI) with an objective to fit the reflection shape, rather than produce reflections, may mitigate the limitations of FWI. Because FWI, performing as a migration operator, is in preference of the high wavenumber updates along reflectors. We propose a nonlinear elastic RWI that inverts for both the low wavenumber and perturbation components of the P- and S-wave velocities. To generate the full elastic reflection wavefields, we derive an equivalent stress source made up by the inverted model perturbations and incident wavefields. We update both the perturbation and propagation parts of the velocity models in a nested fashion. Applications on synthetic isotropic models and field data show that our method can efficiently update the low and high wavenumber parts of the models.

Elastic reflection based waveform inversion with a nonlinear approach

KAUST Repository

Guo, Qiang; Alkhalifah, Tariq Ali

2017-01-01

Full waveform inversion (FWI) is a highly nonlinear problem due to the complex reflectivity of the Earth, and this nonlinearity only increases under the more expensive elastic assumption. In elastic media, we need a good initial P-wave velocity and even a better initial S-wave velocity models with accurate representation of the low model wavenumbers for FWI to converge. However, inverting for the low wavenumber components of P- and S-wave velocities using reflection waveform inversion (RWI) with an objective to fit the reflection shape, rather than produce reflections, may mitigate the limitations of FWI. Because FWI, performing as a migration operator, is in preference of the high wavenumber updates along reflectors. We propose a nonlinear elastic RWI that inverts for both the low wavenumber and perturbation components of the P- and S-wave velocities. To generate the full elastic reflection wavefields, we derive an equivalent stress source made up by the inverted model perturbations and incident wavefields. We update both the perturbation and propagation parts of the velocity models in a nested fashion. Applications on synthetic isotropic models and field data show that our method can efficiently update the low and high wavenumber parts of the models.

The incidence of mesothelioma has not decreased for the last twenty ...

African Journals Online (AJOL)

Background: Malignant pleural Mesothelioma (MPM) is a very rarely encountered tumor in the normal population. Objectives: To investigate the variations in incidence of MPM in Southeast region of Turkey. Methods: We retrospectively investigated the data of 161 MPM patients who were diagnosed from January 2000 to ...

Spatial Distribution of Black Bear Incident Reports in Michigan.

Directory of Open Access Journals (Sweden)

Jamie E McFadden-Hiller

Full Text Available Interactions between humans and carnivores have existed for centuries due to competition for food and space. American black bears are increasing in abundance and populations are expanding geographically in many portions of its range, including areas that are also increasing in human density, often resulting in associated increases in human-bear conflict (hereafter, bear incidents. We used public reports of bear incidents in Michigan, USA, from 2003-2011 to assess the relative contributions of ecological and anthropogenic variables in explaining the spatial distribution of bear incidents and estimated the potential risk of bear incidents. We used weighted Normalized Difference Vegetation Index mean as an index of primary productivity, region (i.e., Upper Peninsula or Lower Peninsula, primary and secondary road densities, and percentage land cover type within 6.5-km2 circular buffers around bear incidents and random points. We developed 22 a priori models and used generalized linear models and Akaike's Information Criterion (AIC to rank models. The global model was the best compromise between model complexity and model fit (w = 0.99, with a ΔAIC 8.99 units from the second best performing model. We found that as deciduous forest cover increased, the probability of bear incident occurrence increased. Among the measured anthropogenic variables, cultivated crops and primary roads were the most important in our AIC-best model and were both positively related to the probability of bear incident occurrence. The spatial distribution of relative bear incident risk varied markedly throughout Michigan. Forest cover fragmented with agriculture and other anthropogenic activities presents an environment that likely facilitates bear incidents. Our map can help wildlife managers identify areas of bear incident occurrence, which in turn can be used to help develop strategies aimed at reducing incidents. Researchers and wildlife managers can use similar mapping

Spatial Distribution of Black Bear Incident Reports in Michigan.

Science.gov (United States)

McFadden-Hiller, Jamie E; Beyer, Dean E; Belant, Jerrold L

2016-01-01

Interactions between humans and carnivores have existed for centuries due to competition for food and space. American black bears are increasing in abundance and populations are expanding geographically in many portions of its range, including areas that are also increasing in human density, often resulting in associated increases in human-bear conflict (hereafter, bear incidents). We used public reports of bear incidents in Michigan, USA, from 2003-2011 to assess the relative contributions of ecological and anthropogenic variables in explaining the spatial distribution of bear incidents and estimated the potential risk of bear incidents. We used weighted Normalized Difference Vegetation Index mean as an index of primary productivity, region (i.e., Upper Peninsula or Lower Peninsula), primary and secondary road densities, and percentage land cover type within 6.5-km2 circular buffers around bear incidents and random points. We developed 22 a priori models and used generalized linear models and Akaike's Information Criterion (AIC) to rank models. The global model was the best compromise between model complexity and model fit (w = 0.99), with a ΔAIC 8.99 units from the second best performing model. We found that as deciduous forest cover increased, the probability of bear incident occurrence increased. Among the measured anthropogenic variables, cultivated crops and primary roads were the most important in our AIC-best model and were both positively related to the probability of bear incident occurrence. The spatial distribution of relative bear incident risk varied markedly throughout Michigan. Forest cover fragmented with agriculture and other anthropogenic activities presents an environment that likely facilitates bear incidents. Our map can help wildlife managers identify areas of bear incident occurrence, which in turn can be used to help develop strategies aimed at reducing incidents. Researchers and wildlife managers can use similar mapping techniques to

Full four-dimensional and reciprocal Mueller matrix bidirectional reflectance distribution function of sintered polytetrafluoroethylene.

Science.gov (United States)

Germer, Thomas A

2017-11-20

We measured the Mueller matrix bidirectional reflectance distribution function (BRDF) of a sintered polytetrafluoroethylene (PTFE) sample over the scattering hemisphere for six incident angles (0°-75° in 15° steps) and for four wavelengths (351 nm, 532 nm, 633 nm, and 1064 nm). The data for each wavelength were fit to a phenomenological description for the Mueller matrix BRDF, which is an extension of the bidirectional surface scattering modes developed by Koenderink and van Doorn [J. Opt. Soc. Am. A.15, 2903 (1998)JOAOD60740-323210.1364/JOSAA.15.002903] for unpolarized BRDF. This description is designed to be complete, to obey the appropriate reciprocity conditions, and to provide a full description of the Mueller matrix BRDF as a function of incident and scattering directions for each wavelength. The description was further extended by linearizing the surface scattering mode coefficients with wavelength. This data set and its parameterization provides a comprehensive on-demand description of the reflectance properties for this commonly used diffuse reflectance reference material over a wide range of wavelengths.

Ellipsometry of single-layer antireflection coatings on transparent substrates

Science.gov (United States)

Azzam, R. M. A.

2017-11-01

The complex reflection coefficients of p- and s-polarized light and ellipsometric parameters of a transparent substrate of refractive index n2, which is coated by a transparent thin film whose refractive index n1 =√{n2 } satisfies the anti-reflection condition at normal incidence, are considered as functions of film thickness d and angle of incidence ϕ. A unique coated surface, with n1 =√{n2 } and film thickness d equal to half of the film-thickness period Dϕ at angle ϕ and wavelength λ, reflects light of the same wavelength without change of polarization for all incident polarization states. (The reflection Jones matrix of such coated surface is the 2 × 2 identity matrix pre-multiplied by a scalar, hence tanΨ = 1,Δ = 0.) To monitor the deposition of an antireflection coating, the normalized Stokes parameters of obliquely reflected light (e.g. at ϕ =70∘) are measured until predetermined target values of those parameters are detected. This provides a more accurate means of film thickness control than is possible using a micro-balance technique or an intensity reflectance method.

Paediatric renal length measurements from ultrasound and DMSA scans: does clinical practice reflect theoretical normal values?

International Nuclear Information System (INIS)

Que, L.; Rutland, M.D.; Hassan, I.M.

1999-01-01

Full text: Renal length measurement is a routine part of ultrasound examination in children and those results are plotted on a normogram style graph, so that each child's results are compared to a normal range (mean ± 2 S.D.). Renal length measurements from the posterior oblique views of dimercaptosuccinic acid (DMSA) scans in our department have not always correlated well with the ultrasound measurements on the same patients. Renal lengths from the DMSA scans of 120 patients with apparently normal kidneys were recorded and used to generate a normogram of renal length at different ages (0.5-7 years). This DMSA normogram was compared to the ultrasound (US) normogram used in the Paediatric Radiology Department, and it showed slight differences in renal lengths (3-8 mm), but that the US normogram had smaller coefficients of variation (US = 6.6%, NM 8.3%), implying a 'tighter' normal range. 39 of these patients had DMSA and ultrasound measurements of renal length within 3 months, and these were studied first by calculating the mean and CV values for different age groups, and then by plotting individual renal lengths on the appropriate normograms. The measured data produced much greater variability in the ultrasound measurements than the DTPA measurements, and the individual points produced 4/78 (5.1%) abnormal results for DMSA, but 21/78 (26.9%) abnormal results for ultrasound. Thus, in routine clinical use, using patients with apparently normal kidneys, ultrasound was unable to match the 'normal range' set by their current normogram, but the nuclear medicine showed 5.1% of values outside the normal (DMSA) range, which was completely appropriate for a range of ± 2 standard deviations

Validation of a spectral correction procedure for sun and sky reflections in above-water reflectance measurements.