WorldWideScience

Sample records for nonreactive plane shear

  1. Continuous shear - a method for studying material elements passing a stationary shear plane

    DEFF Research Database (Denmark)

    Lindegren, Maria; Wiwe, Birgitte; Wanheim, Tarras

    2003-01-01

    Traditionally, material response to shear deformation has been studied with methods where the shear is gradually increasing from zero to the final value over a certain fixed deformation zone, e.g. in the well-known torsion test of a tube with a defined shear zone established by a machined circumf...... and tested with AlMgSil and copper. The sheared material has thereafter been tested n plane strain compression with different orientation concerning the angle between the shear plane and the compression direction....

  2. Continuous shear - a method for studying material elements passing a stationary shear plane

    DEFF Research Database (Denmark)

    Lindegren, Maria; Wiwe, Birgitte; Wanheim, Tarras

    2003-01-01

    Traditionally, material response to shear deformation has been studied with methods where the shear is gradually increasing from zero to the final value over a certain fixed deformation zone, e.g. in the well-known torsion test of a tube with a defined shear zone established by a machined...... circumferential groove. Normally shear in metal forming processes is of another nature, namely where the material elements move through a stationary shear zone, often of small width. In this paper a method enabling the simulation of this situation is presented. A tool for continuous shear has beeen manufactured...... and tested with AlMgSil and copper. The sheared material has thereafter been tested n plane strain compression with different orientation concerning the angle between the shear plane and the compression direction....

  3. Fibre-reinforced plastic composites - Determination of the in-plane shear stress/shear strain response, including the in-plane shear modulus and strength, by the plus or minus 45 degree tension test method

    CERN Document Server

    International Organization for Standardization. Geneva

    1997-01-01

    Fibre-reinforced plastic composites - Determination of the in-plane shear stress/shear strain response, including the in-plane shear modulus and strength, by the plus or minus 45 degree tension test method

  4. In-plane shear test of fibre reinforced concrete panels

    DEFF Research Database (Denmark)

    Solgaard, Anders Ole Stubbe; Stang, Henrik; Goltermann, Per

    2008-01-01

    contributes to the investigation of fibers as reinforcement in panels with experimental results and a consistent approach to material characterization and modeling. The proposed model draws on elements from the classical yield line theory of rigid, perfectly plastic materials and the theory of fracture......The present paper concerns the investigation of polymer Fiber Reinforced Concrete (FRC) panels subjected to in-plane shear. The use of fibers as primary reinforcement in panels is a new application of fiber reinforcement, hence test methods, design bases and models are lacking. This paper...

  5. In-plane shear piezoelectric wafer active sensor phased arrays for structural health monitoring

    Science.gov (United States)

    Wang, Wentao; Zhou, Wensong; Wang, Peng; Wang, Chonghe; Li, Hui

    2016-04-01

    This paper proposes a new way for guided wave structural health monitoring using in-plane shear (d36 type) piezoelectric wafer active sensors phased arrays. Conventional piezoelectric wafer active sensors phased arrays based on inducing into specific Lamb wave modes (d31 type) has already widely used for health monitoring of the thin-wall structures. Rather than Lamb wave modes, the in-plane shear piezoelectric wafer active sensors phased arrays induces in-plane shear horizontal (SH) guided waves. The SH guided waves are distinct with the Lamb waves with simple waveform and less additional converted wave modes and the zero symmetric mode (SH0) is non-dispersive. In this paper, the advantage of the shear horizontal wave and the in-plane shear piezoelectric wafers capability to generate SH waves is first reviewed. Then finite element analysis of a 4-in-plane shear wafer active sensors phased array embedded on a rectangular aluminium plate is performed. In addition, numerical simulations with respect to creaks with different sizes as well as locations are implemented by the in-plane shear wafer active sensors phased array. For comparison purposes, the same numerical simulations using the conventional piezoelectric wafer active sensors phased arrays are also employed at the same time. Results indicate that the in-plane shear (d36 type) piezoelectric wafer active sensors phased arrays has the potential to identify damage location and assess damage severity in structural health monitoring.

  6. Empirical paths of poles to planes (eppps) constrain the kinematics of geological shear zones

    Science.gov (United States)

    Talbot, Christopher J.

    2014-09-01

    Ductile shear zones are tabular bodies of deformed rocks bound by less deformed wall rocks. This work introduces a simple empirical approach to analysing the 3D kinematics of shear zones. The orientations of pre-shear planar markers distorted across natural shear zones by local strains are systematically measured and plotted as poles on lower hemisphere equal area projections that constrain smooth empiricalpaths ofpoles toplanes (eppps). Such eppps recording local strain gradients are used to fix a reference frame to the plane of greatest shear in any homogeneous bulk strain. Assuming that space can be taken as a proxy for time, the curvatures of pre-shear planar markers across shear zones are interpreted as the records of the 3D bulk strain histories of shear zones. The sig- or zig-moidal symmetries of sheared markers record different amounts of the same general strain within the same overall movement pattern (i.e. in a constant flow field) whatever its geometry or history. In effect eppps represent the strain memories of shear zones with successively inward readings recording successively younger shearing. In planes other than the bulk XY, great circle eppps indicate simple shear while hyperbolic eppps indicate pure shear. Eppps for suites of shear zones in Proterozoic gneisses in Sweden exhibit the parabolic shapes indicative of pure rather than simple shear.

  7. Effects of texture on shear band formation in plane strain tension/compression and bending

    DEFF Research Database (Denmark)

    Kuroda, M.; Tvergaard, Viggo

    2007-01-01

    model analysis. Third, shear band developments in plane strain pure bending of a sheet specimen with the typical textures are studied. Regions near the surfaces in a bent sheet specimen are approximately subjected to plane strain tension or compression. From this viewpoint, the bendability of a sheet......In this study, effects of typical texture components observed in rolled aluminum alloy sheets on shear band formation in plane strain tension/compression and bending are systematically studied. The material response is described by a generalized Taylor-type polycrystal model, in which each grain...... are obtained: i.e. the critical strain at the onset of shear banding and the corresponding orientation of shear band. Second, the shear band development in plane strain tension/compression is analyzed by the finite element method. Predictability of the finite element analysis is compared to that of the simple...

  8. Evaluation of in-plane shear test methods for composite material laminates

    Institute of Scientific and Technical Information of China (English)

    WANG Yan-lei; HAO Qing-duo; OU Jin-ping

    2007-01-01

    In-plane shear properties of composite material laminates are very important in structural design of composite material. Four commonly used in-plane shear test methods were introduced in this paper. In order to study the differences of various shear test methods, two ASTM standard in-plane shear test methods for composite material laminates were experimentally investigated. They are ±45℃ tensile shear test (ASTM D3518) and V-notched rail shear test (ASTM D7078). Five types of composite material laminates composed of E-glass fiber fabric and vinyl ester resin were utilized, whose stacking sequences are [0]3s, [0/90]3s, [CSM/0/90]2s, [±45]3s and [(0/90)2/(±45)2/(0/90)2]s, respectively. The test results indicate that the±45℃ tensile shear test can predict shear moduli of composite material laminates accurately. However, the predictions of shear strength using±45℃ tensile shear test are significantly lower than those of V-notched rail shear test.

  9. Evaluation of stresses in a combined plane strain-simple shear test

    NARCIS (Netherlands)

    Boogaard, van den A.H.; Riel, van M.; Huetink, J.

    2005-01-01

    A biaxial testing device for sheet metal has been developed that can impose a combination of plane strain and simple shear deformation. The specimen has a large width to height ratio and a small height to thickness ratio. The forces in tensile and shear direction are easily measured and the tensile

  10. Study of shear-thinning/thickening effects on plane Couette-Poiseuille flow with uniform crossflow

    Institute of Scientific and Technical Information of China (English)

    刘玉泉; 朱克勤

    2014-01-01

    The shear-thinning/thickening effects on the plane Couette-Poiseuille flow with a uniform crossflow are studied. The detailed solution procedures for both theo-retical and numerical purposes are given. In order to clarify the difference between the Newtonian flow and the power-law flow, all cases of the plane Couette-Poiseuille flows with uniform crossflows for different power indexes are assigned to the phase diagram in the parameter plane corresponding to the Couette number and the crossflow Reynolds number. The effects of shear-thinning/thickening on the phase diagram are discussed. An important feature of the shear-thinning circumstance distinguished from the shear-thickening circumstance is discovered.

  11. Oblique Laminar-Turbulent Interfaces in Plane Shear Flows

    Science.gov (United States)

    Duguet, Yohann; Schlatter, Philipp

    2013-01-01

    Localized structures such as turbulent stripes and turbulent spots are typical features of transitional wall-bounded flows in the subcritical regime. Based on an assumption for scale separation between large and small scales, we show analytically that the corresponding laminar-turbulent interfaces are always oblique with respect to the mean direction of the flow. In the case of plane Couette flow, the mismatch between the streamwise flow rates near the boundaries of the turbulence patch generates a large-scale flow with a nonzero spanwise component. Advection of the small-scale turbulent fluctuations (streaks) by the corresponding large-scale flow distorts the shape of the turbulence patch and is responsible for its oblique growth. This mechanism can be easily extended to other subcritical flows such as plane Poiseuille flow or Taylor-Couette flow.

  12. Chirality-specific lift forces of helix under shear flows: Helix perpendicular to shear plane.

    Science.gov (United States)

    Zhang, Qi-Yi

    2017-02-01

    Chiral objects in shear flow experience a chirality-specific lift force. Shear flows past helices in a low Reynolds number regime were studied using slender-body theory. The chirality-specific lift forces in the vorticity direction experienced by helices are dominated by a set of helix geometry parameters: helix radius, pitch length, number of turns, and helix phase angle. Its analytical formula is given. The chirality-specific forces are the physical reasons for the chiral separation of helices in shear flow. Our results are well supported by the latest experimental observations.

  13. In-plane Shear Joint Capacity of Pracast Lightweight Aggregate Concrete Elements

    DEFF Research Database (Denmark)

    Larsen, Henning; Goltermann, Per; Scherfig, Søren;

    1996-01-01

    The paper establishes and documents formulas for the in-plane shear capacity between precast elements of lightweight aggregate concrete with open structure. The joints investigated are rough or toothed and have all been precracked prior to the testing in order to obtain realistic test results...

  14. The growth and coalescence of ellipsoidal voids in plane strain under combined shear and tension

    NARCIS (Netherlands)

    Scheyvaerts, F.; Onck, P. R.; Tekoglu, C.; Pardoen, T.

    2011-01-01

    New extensions of a model for the growth and coalescence of ellipsoidal voids based on the Gurson formalism are proposed in order to treat problems involving shear and/or voids axis not necessarily aligned with the main loading direction, under plane strain loading conditions. These extensions are m

  15. A comparative evaluation of in-plane shear test methods for laminated graphite-epoxy composites

    Science.gov (United States)

    Morton, John; Ho, Henjen

    1992-01-01

    The objectives were to evaluate popular shear test methods for various forms of graphite-epoxy composite materials and to determine the shear response of graphite-epoxy composites with various forms of fiber architecture. Numerical and full-field experimental stress analyses were performed on four shear test configurations for unidirectional and bidirectional graphite-epoxy laminates to assess the uniformity and purity of the shear stress (strain) fields produced in the specimen test section and to determine the material in-plane shear modulus and shear response. The test methods were the 10 deg off-axis, the +/- 45 deg tension, the Iosipescu V-notch, and a compact U-notch specimen. Specimens were prepared from AS4/3501-6 graphite-epoxy panels, instrumented with conventional strain gage rosettes and with a cross-line moire grating, and loaded in a convenient testing machine. The shear responses obtained for each test method and the two methods of specimen instrumentation were compared. In a second phase of the program the shear responses obtained from Iosipescu V-notch beam specimens were determined for woven fabric geometries of different weave and fiber architectures. Again the responses of specimens obtained from strain gage rosettes and moire interferometry were compared. Additional experiments were performed on a bidirectional cruciform specimen which was also instrumented with strain gages and a moire grating.

  16. Shear heating by translational brittle reverse faulting along a single, sharp and straight fault plane

    Indian Academy of Sciences (India)

    Soumyajit Mukherjee

    2017-02-01

    Shear heating by reverse faulting on a sharp straight fault plane is modelled. Increase in temperature (Ti) of faulted hangingwall and footwall blocks by frictional/shear heating for planar rough reverse faults is proportional to the coefficient of friction (μ), density and thickness of the hangingwall block (ρ). Ti increases as movement progresses with time. Thermal conductivity (Ki) and thermal diffusivity (k'i) of faulted blocks govern Ti but they do not bear simple relation. Ti is significant only near the fault plane. If the lithology is dry and faulting brings adjacent hangingwall and footwall blocks of the same lithology in contact, those blocks undergo the same rate of increase in shear heating per unit area per unit time.

  17. Nonlinear transverse cascade and two-dimensional magnetohydrodynamic subcritical turbulence in plane shear flows.

    Science.gov (United States)

    Mamatsashvili, G R; Gogichaishvili, D Z; Chagelishvili, G D; Horton, W

    2014-04-01

    We find and investigate via numerical simulations self-sustained two-dimensional turbulence in a magnetohydrodynamic flow with a maximally simple configuration: plane, noninflectional (with a constant shear of velocity), and threaded by a parallel uniform background magnetic field. This flow is spectrally stable, so the turbulence is subcritical by nature and hence it can be energetically supported just by a transient growth mechanism due to shear flow non-normality. This mechanism appears to be essentially anisotropic in the spectral (wave-number) plane and operates mainly for spatial Fourier harmonics with streamwise wave numbers less than the ratio of flow shear to Alfvén speed, kymagnetohydrodynamic (MHD) turbulence research. We find similarity of the nonlinear dynamics to the related dynamics in hydrodynamic flows: to the bypass concept of subcritical turbulence. The essence of the analyzed nonlinear MHD processes appears to be a transverse redistribution of kinetic and magnetic spectral energies in the wave-number plane [as occurs in the related hydrodynamic flow; see Horton et al., Phys. Rev. E 81, 066304 (2010)] and differs fundamentally from the existing concepts of (anisotropic direct and inverse) cascade processes in MHD shear flows.

  18. Optical measurement on dynamic buckling behavior of stiffened composite panels under in-plane shear

    Science.gov (United States)

    Lei, Zhenkun; Bai, Ruixiang; Tao, Wang; Wei, Xiao; Leng, Ruijiao

    2016-12-01

    The buckling behavior and failure mode of a composite panel stiffened by I-shaped stringers under in-plane shear is studied using digital fringe projection profilometry. The basic principles of the dynamic phase-shifting technique, multi-frequency phase-unwrapping technique and inverse-phase technique for nonlinear error compensation are introduced. Multi-frequency fringe projection profilometry was used to monitor and measure the change in the morphology of a discontinuous surface of the stiffened composite panel during in-plane shearing. Meanwhile, the strain history of multiple points on the skin was obtained using strain rosettes. The buckling mode and deflection of the panel at different moments were analyzed and compared with those obtained using the finite element method. The experimental results validated the FEM analysis.

  19. Simultaneous inversion of layered compressional velocity and shear velocity by using plane wave seismogram

    Institute of Scientific and Technical Information of China (English)

    宋海斌; 马在田; 张关泉

    1996-01-01

    A layer-stripping method is presented for simultaneous inversion of compressional velocity and shear velocity in layered medium from single precritical-incident-angle data of P-P and P-SV plane wave seismogram. A finite bandwidth algorithm is provided and results obviously better than previous research work are obtained by the numerical experiments for band-limited seismogram and synthetic data including noise.

  20. On the role of vortex stretching in energy optimal growth of three dimensional perturbations on plane parallel shear flows

    CERN Document Server

    Heifetz, H Vitoshkin E; Harnik, N

    2012-01-01

    The three dimensional optimal energy growth mechanism, in plane parallel shear flows, is reexamined in terms of the role of vortex stretching and the interplay between the span-wise vorticity and the planar divergent components. For high Reynolds numbers the structure of the optimal perturbations in Couette, Poiseuille, and mixing layer shear profiles is robust and resembles localized plane-waves in regions where the background shear is large. The waves are tilted with the shear when the span-wise vorticity and the planar divergence fields are in (out of) phase when the background shear is positive (negative). A minimal model is derived to explain how this configuration enables simultaneous growth of the two fields, and how this mutual amplification reflects on the optimal energy growth. This perspective provides an understanding of the three dimensional growth solely from the two dimensional dynamics on the shear plane.

  1. The plane strain shear fracture of the advanced high strength steels

    Science.gov (United States)

    Sun, Li

    2013-12-01

    The "shear fracture" which occurs at the high-curvature die radii in the sheet metal forming has been reported to remarkably limit the application of the advanced high strength steels (AHSS) in the automobile industry. However, this unusual fracture behavior generally cannot be predicted by the traditional forming limit diagram (FLD). In this research, a new experimental system was developed in order to simulate the shear fracture, especially at the plane strain state which is the most common state in the auto-industry and difficult to achieve in the lab due to sample size. Furthermore, the system has the capability to operate in a strain rate range from quasi-static state to the industrial forming state. One kinds of AHSS, Quenching-Partitioning (QP) steels have been performed in this test and the results show that the limiting fracture strain is related to the bending ratio and strain rate. The experimental data support that deformation-induced heating is an important cause of "shear fracture" phenomena for AHSS: a deformation-induced quasi-heating caused by smaller bending ratio and high strain rate produce a smaller limiting plane strain and lead a "shear fracture" in the component.

  2. The plane strain shear fracture of the advanced high strength steels

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Li, E-mail: li.sun@gm.com [General Motors China Science Lab, No.56 Jinwan Road, Shanghai, 201206 (China)

    2013-12-16

    The “shear fracture” which occurs at the high-curvature die radii in the sheet metal forming has been reported to remarkably limit the application of the advanced high strength steels (AHSS) in the automobile industry. However, this unusual fracture behavior generally cannot be predicted by the traditional forming limit diagram (FLD). In this research, a new experimental system was developed in order to simulate the shear fracture, especially at the plane strain state which is the most common state in the auto-industry and difficult to achieve in the lab due to sample size. Furthermore, the system has the capability to operate in a strain rate range from quasi-static state to the industrial forming state. One kinds of AHSS, Quenching-Partitioning (QP) steels have been performed in this test and the results show that the limiting fracture strain is related to the bending ratio and strain rate. The experimental data support that deformation-induced heating is an important cause of “shear fracture” phenomena for AHSS: a deformation-induced quasi-heating caused by smaller bending ratio and high strain rate produce a smaller limiting plane strain and lead a “shear fracture” in the component.

  3. The radiation of sound by the instability waves of a compressible plane turbulent shear layer

    Science.gov (United States)

    Tam, C. K. W.; Morris, P. J.

    1980-01-01

    The problem of acoustic radiation generated by instability waves of a compressible plane turbulent shear layer is solved. The solution provided is valid up to the acoustic far-field region. It represents a significant improvement over the solution obtained by classical hydrodynamic-stability theory which is essentially a local solution with the acoustic radiation suppressed. The basic instability-wave solution which is valid in the shear layer and the near-field region is constructed in terms of an asymptotic expansion using the method of multiple scales. This solution accounts for the effects of the slightly divergent mean flow. It is shown that the multiple-scales asymptotic expansion is not uniformly valid far from the shear layer. Continuation of this solution into the entire upper half-plane is described. The extended solution enables the near- and far-field pressure fluctuations associated with the instability wave to be determined. Numerical results show that the directivity pattern of acoustic radiation into the stationary medium peaks at 20 degrees to the axis of the shear layer in the downstream direction for supersonic flows. This agrees qualitatively with the observed noise-directivity patterns of supersonic jets.

  4. The growth and coalescence of ellipsoidal voids in plane strain under combined shear and tension

    Science.gov (United States)

    Scheyvaerts, F.; Onck, P. R.; Tekogˇlu, C.; Pardoen, T.

    2011-02-01

    New extensions of a model for the growth and coalescence of ellipsoidal voids based on the Gurson formalism are proposed in order to treat problems involving shear and/or voids axis not necessarily aligned with the main loading direction, under plane strain loading conditions. These extensions are motivated and validated using 3D finite element void cell calculations with overall plane strain enforced in one direction. The starting point is the Gologanu model dealing with spheroidal void shape. A void rotation law based on homogenization theory is coupled to this damage model. The predictions of the model closely agree with the 3D cell calculations, capturing the effect of the initial void shape and orientation on the void rotation rate. An empirical correction is also introduced for the change of the void aspect ratio in the plane transverse to the main axis of the void departing from its initially circular shape. This correction is needed for an accurate prediction of the onset of coalescence. Next, a new approach is proposed to take strain hardening into account within the Thomason criterion for internal necking, avoiding the use of strain hardening-dependent fitting parameters. The coalescence criterion is generalized to any possible direction of the coalescence plane and void orientation. Finally, the model is supplemented by a mathematical description of the final drop of the stress carrying capacity during coalescence. The entire model is developed for plane strain conditions, setting the path to a 3D extension. After validation of the model, a parametric study addresses the effect of shear on the ductility of metallic alloys for a range of microstructural and flow parameters, under different stress states. In general, the presence of shear, for identical stress triaxiality, decreases the ductility, partly explaining recent experimental results obtained in the low stress triaxiality regime.

  5. Bounds on the Phase Velocity in the Linear Instability of Viscous Shear Flow Problem in the -Plane

    Indian Academy of Sciences (India)

    R G Shandil; Jagjit Singh

    2003-05-01

    Results obtained by Joseph (J. Fluid Mech. 33 (1968) 617) for the viscous parallel shear flow problem are extended to the problem of viscous parallel, shear flow problem in the beta plane and a sufficient condition for stability has also been derived.

  6. Trapping of Oxygen Vacancies at Crystallographic Shear Planes in Acceptor-Doped Pb-Based Ferroelectrics.

    Science.gov (United States)

    Batuk, Dmitry; Batuk, Maria; Tsirlin, Alexander A; Hadermann, Joke; Abakumov, Artem M

    2015-12-01

    The defect chemistry of the ferroelectric material PbTiO3 after doping with Fe(III) acceptor ions is reported. Using advanced transmission electron microscopy and powder X-ray and neutron diffraction, we demonstrate that even at concentrations as low as circa 1.7% (material composition approximately ABO2.95), the oxygen vacancies are trapped into extended planar defects, specifically crystallographic shear planes. We investigate the evolution of these defects upon doping and unravel their detailed atomic structure using the formalism of superspace crystallography, thus unveiling their role in nonstoichiometry in the Pb-based perovskites.

  7. Shear Creep Simulation of Structural Plane of Rock Mass Based on Discontinuous Deformation Analysis

    Directory of Open Access Journals (Sweden)

    Guoxin Zhang

    2017-01-01

    Full Text Available Numerical simulations of the creep characteristics of the structural plane of rock mass are very useful. However, most existing simulation methods are based on continuum mechanics and hence are unsuitable in the case of large displacements and deformations. The discontinuous deformation analysis method proposed by Genhua is a discrete one and has a significant advantage when simulating the contacting problem of blocks. In this study, we combined the viscoelastic rheological model of Burgers with the discontinuous deformation analysis (DDA method. We also derived the recurrence formula for the creep deformation increment with the time step during numerical simulations. Based on the minimum potential energy principle, the general equilibrium equation was derived, and the shear creep deformation in the structural plane was considered. A numerical program was also developed and its effectiveness was confirmed based on the curves obtained by the creep test of the structural plane of a rock mass under different stress levels. Finally, the program was used to analyze the mechanism responsible for the creep features of the structural plane in the case of the toppling deformation of the rock slope. The results showed that the extended DDA method is an effective one.

  8. Influence of Tissue Microstructure on Shear Wave Speed Measurements in Plane Shear Wave Elastography: A Computational Study in Lossless Fibrotic Liver Media.

    Science.gov (United States)

    Wang, Yu; Jiang, Jingfeng

    2017-07-01

    Shear wave elastography (SWE) has been used to measure viscoelastic properties for characterization of fibrotic livers. In this technique, external mechanical vibrations or acoustic radiation forces are first transmitted to the tissue being imaged to induce shear waves. Ultrasonically measured displacement/velocity is then utilized to obtain elastographic measurements related to shear wave propagation. Using an open-source wave simulator, k-Wave, we conducted a case study of the relationship between plane shear wave measurements and the microstructure of fibrotic liver tissues. Particularly, three different virtual tissue models (i.e., a histology-based model, a statistics-based model, and a simple inclusion model) were used to represent underlying microstructures of fibrotic liver tissues. We found underlying microstructures affected the estimated mean group shear wave speed (SWS) under the plane shear wave assumption by as much as 56%. Also, the elastic shear wave scattering resulted in frequency-dependent attenuation coefficients and introduced changes in the estimated group SWS. Similarly, the slope of group SWS changes with respect to the excitation frequency differed as much as 78% among three models investigated. This new finding may motivate further studies examining how elastic scattering may contribute to frequency-dependent shear wave dispersion and attenuation in biological tissues.

  9. The Application of Statistical Design of Experiments to Study the In-Plane Shear Behaviour of Hybrid Composite Sandwich Panel

    Directory of Open Access Journals (Sweden)

    Fajrin J.

    2016-03-01

    Full Text Available This paper presents a statistical aspect of experimental study on the in-plane shear behaviour of hybrid composite sandwich panel with intermediate layer. The study was aimed at providing information of how significant the contribution of intermediate layer to the in-plane shear behaviour of new developed sandwich panel. The investigation was designed as a single factor experimental design and the results were throughly analysed with statistics software; Minitab 15. The panels were tested by applying a tensile force along the diagonal of the test frame simulating pure shear using a 100 kN MTS servo-hydraulic UTM. The result shows that the incorporation of intermediate layer has sinificantly enhanced the in-plane shear behaviour of hybrid composite sandwich panel. The statistical analysis shows that the value of F0 is much higher than the value of Ftable, which has a meaning that the improvement provided by the incorporation of intermediate layer is statistically significant.

  10. Radiation of a Plane Shear Wave from an Elastic Waveguide to a Composite Elastic Space

    Directory of Open Access Journals (Sweden)

    Grigoryan E.Kh.

    2007-09-01

    Full Text Available The radiation of a plane shear wave from an elastic strip (waveguide to an elastic space is investigated in this paper. The strip is embedded into a space and is partially bonded with it. A given plane shear wave propagates from the free part of the strip and radiates into the composite space. The problem’s solution is led to a system of two uncoupled functional Wiener-Hopf type equations which are solved via the method of factorization. Closed form expressions are obtained which determine the wavefield in all the parts of the strip and space. Asymptotic expressions are provided which represent the wavefield in the far field and in the neighborhood of the contact zones. From these formulas it follows that: a in the cases of several values of the ratio of the wave numbers of the strip and space the order of vanishing of the volume wave in the strip becomes less and equal to the one in the case of a homogeneous material, b the radiated volume wave in the strip has a velocity of propagation equal to the volume wave’s velocity in the space.

  11. Crack Growth Mechanisms under Anti-Plane Shear in Composite Laminates

    Science.gov (United States)

    Horner, Allison Lynne

    The research conducted for this dissertation focuses on determining the mechanisms associated with crack growth in polymer matrix composite laminates subjected to anti-plane shear (mode III) loading. For mode III split-beam test methods were proposed, and initial evaluations were conducted. A single test method was selected for further evaluation. Using this test method, it was determined that the apparent mode III delamination toughness, GIIIc , depended on geometry, which indicated a true material property was not being measured. Transverse sectioning and optical microscopy revealed an array of transverse matrix cracks, or echelon cracks, oriented at approximately 45° and intersecting the plane of the delamination. Subsequent investigations found the echelon array formed prior to the onset of planar delamination advance and that growth of the planar delamination is always coupled to echelon array formation in these specimens. The evolution of the fracture surfaces formed by the echelon array and planar delamination were studied, and it was found that the development was similar to crack growth in homogenous materials subjected to mode III or mixed mode I-III loading, although the composite laminate architecture constrained the fracture surface development differently than homogenous materials. It was also found that, for split-beam specimens such as those used herein, applying an anti-plane shear load results in twisting of the specimen's uncracked region which gives rise to a mixed-mode I-III load condition. This twisting has been related to the apparent mode III toughness as well as the orientation of the transverse matrix cracks. A finite element model was then developed to study the mechanisms of initial echelon array formation. From this, it is shown that an echelon array will develop, but will become self-limiting prior to the onset of planar delamination growth.

  12. Fabrication of simulated plate fuel elements: Defining role of out-of-plane residual shear stress

    Science.gov (United States)

    Rakesh, R.; Kohli, D.; Sinha, V. P.; Prasad, G. J.; Samajdar, I.

    2014-02-01

    Bond strength and microstructural developments were investigated during fabrication of simulated plate fuel elements. The study involved roll bonding of aluminum-aluminum (case A) and aluminum-aluminum + yttria (Y2O3) dispersion (case B). Case B approximated aluminum-uranium silicide (U3Si2) 'fuel-meat' in an actual plate fuel. Samples after different stages of fabrication, hot and cold rolling, were investigated through peel and pull tests, micro-hardness, residual stresses, electron and micro-focus X-ray diffraction. Measurements revealed a clear drop in bond strength during cold rolling: an observation unique to case B. This was related to significant increase in 'out-of-plane' residual shear stresses near the clad/dispersion interface, and not from visible signatures of microstructural heterogeneities.

  13. Diffraction of a Shear Plane Wave in Elastic Medium with Piecewise Homogeneous Infinite Inclusion

    Directory of Open Access Journals (Sweden)

    Voskanyan A. R.

    2007-06-01

    Full Text Available Diffraction of shear plane wave incident from infinity at arbitrary angle on infinite inclusion is considered. The infinite inclusion consists of two semi-infinite parts made of different materials. The problem’s solution is presented in the form of sum of its even and odd problems. The case of long waves is considered and these problems (the even and odd ones are modelled in a corresponding way after which each of them is reduced to the solution of Wiener-Hopf functional equation. Asymptotic formulas are obtained for displacement’s amplitude and contacts stresses in the far field. The behaviors of contact stresses in the neighborhood of the bonding line of the semi-infinite parts of the inclusion are also obtained.

  14. Debonding of an elastic inhomogeneity of arbitrary shape in anti-plane shear

    Science.gov (United States)

    Wang, Xu; Yang, Moxuan; Schiavone, Peter

    2016-08-01

    We investigate the anti-plane shear problem of a curvilinear crack lying along the interface of an arbitrarily shaped elastic inhomogeneity embedded in an infinite matrix subjected to uniform stresses at infinity. Complex variable and conformal mapping techniques are used to derive an analytical solution in series form. The problem is first reduced to a non-homogeneous Riemann-Hilbert problem, the solution of which can be obtained by evaluating the associated Cauchy integral. A set of linear algebraic equations is obtained from the compatibility condition imposed on the resulting analytic function defined in the inhomogeneity and its Faber series expansion. Each of the unknown coefficients in the corresponding analytic functions can then be uniquely determined by solving the linear algebraic equations, which are written concisely in matrix form. The resulting analytical solution is then used to quantify the displacement jump across the debonded section of the interface as well as the traction distribution along the bonded section of the interface. In addition, our solution allows us to obtain mode-III stress intensity factors at the two crack tips. The solution to the anti-plane problem of a partially debonded elliptical inhomogeneity containing a confocal crack is also derived using a similar method.

  15. Experimental study on time-dependent stress and strain of in-plane shear(ModeⅡ) fracture process of rock

    Institute of Scientific and Technical Information of China (English)

    王志; 饶秋华; 谢海峰

    2008-01-01

    Shear-box test with strain measurement was used to study time-dependent stress and strain of in-plane shear(Mode Ⅱ) fracture process of rock and to reveal the mechanism of Mode Ⅱ fracture.Numerical results show that the maximum shear stress τmax at the crack tip is much larger than the maximum tensile stress σ1 and the ratio of τmax/σ1 is about 5,which favors Mode Ⅱ fracture of rock.Test results indicate that the strain-time curve comprises three stages:the linear deformation stage,the micro-cracking stage and the macroscopic crack propagation.The strain in the direction of the original notch plane is negative,due to restraining effect of compressive loading applied to the original notch plane.Both σ1 and τmax are increased as the load increases,but the slope of τmax is larger than that of σ1 and the value of τmax is always larger than that of σ1.Therefore,τmax reaches its limited value at peak load before σ1 and results in Mode Ⅱ fracture of rock.Shear-box(i.e.compression-shear) test becomes a potential standard method for achieving the true Mode Ⅱ fracture and determining Mode Ⅱ fracture toughness of rock.

  16. Inertial effects on thin-film wave structures with imposed surface shear on an inclined plane

    Science.gov (United States)

    Sivapuratharasu, M.; Hibberd, S.; Hubbard, M. E.; Power, H.

    2016-06-01

    This study provides an extended approach to the mathematical simulation of thin-film flow on a flat inclined plane relevant to flows subject to high surface shear. Motivated by modelling thin-film structures within an industrial context, wave structures are investigated for flows with moderate inertial effects and small film depth aspect ratio ε. Approximations are made assuming a Reynolds number, Re ∼ O(ε-1) and depth-averaging used to simplify the governing Navier-Stokes equations. A parallel Stokes flow is expected in the absence of any wave disturbance and a generalisation for the flow is based on a local quadratic profile. This approach provides a more general system which includes inertial effects and is solved numerically. Flow structures are compared with studies for Stokes flow in the limit of negligible inertial effects. Both two-tier and three-tier wave disturbances are used to study film profile evolution. A parametric study is provided for wave disturbances with increasing film Reynolds number. An evaluation of standing wave and transient film profiles is undertaken and identifies new profiles not previously predicted when inertial effects are neglected.

  17. Role of viscoelasticity in instability in plane shear flow over a deformable solid

    Indian Academy of Sciences (India)

    Paresh Chokshi

    2015-05-01

    The stability of the flow of a viscoelastic fluid over a deformable elastic solid medium is reviewed focusing on the role played by the fluid elasticity on the earlier known instability modes for the Newtonian fluids. In particular, two classes of modes are emphasized: the viscous mode for the creeping flow, and the wall mode for high Reynolds number flow. The flow geometry is restricted to plane Couette flow of fluid supported on elastic substrate of finite thickness. The viscoelastic fluid is described using the Oldroyd-B model and the dynamics of the deformable solid continuum is described by either Hookean or neo-Hookean elastic model. In the limit of $Re \\to 0$, the introduction of fluid elasticity delays the onset of instability and for sufficiently viscoelastic fluid with dilute polymer concentration, the instability is suppressed rendering the flow stable. For concentrated solution and polymer melt, the instability persists, but with higher value of critical shear rate than for the Newtonian fluid, indicating stabilizing role of fluid elasticity in creeping flow regime. However, for high Reynolds number flow of dilute polymer solution, the polymer addition plays a destabilizing role for wall modes, indicated by reduction in critical Reynolds number by an order of magnitude.

  18. MM98.21 Method for studying material element passing a stationary shear plane

    DEFF Research Database (Denmark)

    Lindegren, Maria; Wiwe, Birgitte; Christensen, Thomas

    1998-01-01

    Traditionally, material response to shear deformation has been studied with methods where the shear is gradually increasing from zero to the final value over a certain fixed deformation zone as e.g. in the well-known torsion test of tube with a defined shear zone established by a machined...... circumferential grove. Normally shear in metal forming processes are of another nature, namely where the material elements move through a stationary shear zone, often of small width. In this paper a method enabling the simulation of this situation is suggested....

  19. MM98.21 Method for studying material element passing a stationary shear plane

    DEFF Research Database (Denmark)

    Lindegren, Maria; Wiwe, Birgitte; Christensen, Thomas

    1998-01-01

    Traditionally, material response to shear deformation has been studied with methods where the shear is gradually increasing from zero to the final value over a certain fixed deformation zone as e.g. in the well-known torsion test of tube with a defined shear zone established by a machined...... circumferential grove. Normally shear in metal forming processes are of another nature, namely where the material elements move through a stationary shear zone, often of small width. In this paper a method enabling the simulation of this situation is suggested....

  20. Controlling the formation of wrinkles in a single layer graphene sheet subjected to in-plane shear

    KAUST Repository

    Duan, Wen Hui

    2011-08-01

    The initiation and development of wrinkles in a single layer graphene sheet subjected to in-plane shear displacements are investigated. The dependence of the wavelength and amplitude of wrinkles on the applied shear displacements is explicitly obtained with molecular mechanics simulations. A continuum model is developed for the characteristics of the wrinkles which show that the wrinkle wavelength decreases with an increase in shear loading, while the amplitude of the wrinkles is found to initially increase and then become stable. The propagation and growth process of the wrinkles in the sheet is elucidated. It is expected that the research could promote applications of graphenes in the transportation of biological systems, separation science, and the development of the fluidic electronics. © 2011 Elsevier Ltd. All rights reserved.

  1. Measurement of In-Plane Shear Strength of Carbon/Carbon Composites by Compression of Double-Notched Specimens

    Science.gov (United States)

    Yan, K. F.; Zhang, C. Y.; Qiao, S. R.; Song, C. Z.; Han, D.; Li, M.

    2012-01-01

    The compression of a double-notched specimen was used to determine the in-plane shear strength (IPSS) of a carbon/carbon composite in the paper. The effects of the notch distance ( L), thickness ( T), and notch width ( W) and supporting jig on the IPSS of the double-notched specimens were investigated numerically and experimentally. The fracture surfaces were examined by a scanning electron microscope. It was found that the IPSS varied with L. Thin specimen yielded low strength. W has little effect on IPSS. The main failure modes include the matrix shear cracking, delamination, fracture and pullout of fibers or fiber bundles. Meanwhile, a supporting jig can provide lateral support and prevent buckling, therefore lead to the failure in a shear mode.

  2. Transport coefficients and orientational distributions of spheroidal particles with magnetic moment normal to the particle axis (Analysis for an applied magnetic field normal to the shear plane).

    Science.gov (United States)

    Satoh, Akira; Ozaki, Masataka

    2006-06-15

    We have investigated the influence of the magnetic field strength, shear rate, and rotational Brownian motion on transport coefficients such as viscosity and diffusion coefficient, and also on the orientational distributions of rodlike particles of a dilute colloidal dispersion. The rodlike particle is modeled as a magnetic spheroidal particle which has a magnetic moment normal to the particle axis; such a particle may typically be a hematite particle. In the present study, an external magnetic field is applied in the direction normal to the shear plane of a simple shear flow. The basic equation of the orientational distribution function has been derived from the balance of torques and solved numerically. The results obtained here are summarized as follows. Although the orientational distribution function shows a sharp peak in the shear flow direction for a very strong magnetic field, such a peak is not restricted to the field direction alone, but continues in every direction of the shear plane. This is due to the characteristic particle motion that the particle can rotate around the axis of the magnetic moment in the shear plane, although the magnetic moment nearly points to the magnetic field direction. This particle motion in the shear plane causes negative values of the viscosity due to the magnetic field. The viscosity decreases, attains a minimum value, and then converges to zero as the field strength increases. Additionally, the diffusion coefficient is significantly influenced by such characteristic particle motion in the shear plane for a strong magnetic field.

  3. Moebius resistor is noninductive and nonreactive

    Science.gov (United States)

    Davis, R. L.

    1968-01-01

    Moebius strip made of insulated resistive materials with electrical leads attached directly opposite one another provides a noninductive, nonreactive resistor which is simple, inexpensive, and flexible in usage, and can be made to almost any desired size and shape.

  4. ELECTROELASTIC FIELD FOR AN IMPERMEABLE ANTI-PLANE SHEAR CRACK IN A PIEZOELECTRIC CERAMICS PLATE

    Institute of Scientific and Technical Information of China (English)

    李显方; 范天佑

    2002-01-01

    Electroelastic behavior of a cracked piezoelectric ceramics plate subjected to four cases of combined mechanical-electrical Ioads is analyzed. The integral transform method is applied to convert the problem involving an impermeable anti-plane crack to dual integral equations . Solving the resulting equations, the explicit analytic expressions for electroelastic field along the crack line and the intensity factors of relevant quantities near the crack tip and the mechanical strain energy release rate are obtained. The known results for an infinite piezoelectric ceramics plane containing an impermeable anti-plane crack are recoveredfrom the present results only if the thickness of the plate h → ∞.

  5. Analytical Solution for Predicting In-plane Elastic Shear Properties of 2D Orthogonal PWF Composites

    Institute of Scientific and Technical Information of China (English)

    CHENG Xu; XIONG Junjiang; BAI Jiangbo

    2012-01-01

    This paper proposes a new analytical solution to predict the shear modulus of a two-dimensional (2D) plain weave fabric (PWF) composite accounting for the interaction of orthogonal interlacing strands with coupled shear deformation modes including not only relative bending but also torsion,etc.The two orthogonal yams in a micromechanical unit cell are idealized as curved beams with a path depicted by using sinusoidal shape functions.The intemal forces and macroscopic deformations carried by the yarn families,together with macroscopic shear modulus of PWFs are derived by means of a strain energy approach founded on micromechanics.Three sets of experimental data pertinent to three kinds of 2D orthogonal PWF composites have been implemented to validate the new model.The calculations from the new model are also compared with those by using two models in the earlier literature.It is shown that the experimental results correlate well with predictions from the new model.

  6. Modeling of fan formation in a shear rupture head on the basis of singular solutions of plane elasticity

    Science.gov (United States)

    Tarasov, B. G.; Sadovskii, V. M.

    2016-10-01

    Mathematical model of the equilibrium fan-structure formation between two elastic half-planes is constructed, simulating a shear rupture at stress conditions of seismogenic depths. The stress-strain state far from the fan-structure is analyzed with the help of solution of the problem on the Volterra edge dislocation resulted in estimation of the fan length. The model of formation of two differently directed fans due to the localized action of tangential stress, which pushes two edge dislocations with the antiparallel Burgers vectors, is proposed and analysed.

  7. THE BEHAVIOR OF TWO COLLINEAR CRACKS IN MAGNETO-ELECTRO-ELASTIC COMPOSITES UNDER ANTI-PLANE SHEAR STRESS LOADING

    Institute of Scientific and Technical Information of China (English)

    Sun Yuguo; Zhou Zhengong

    2005-01-01

    In this paper, the behavior of two collinear cracks in magneto-electro-elastic composite material under anti-plane shear stress loading is studied by the Schmidt method for permeable electric boundary conditions. By using the Fourier transform, the problem can be solved with a set of triple integral equations in which the unknown variable is the jump of displacements across the crack surfaces. In solving the triple integral equations, the unknown variable is expanded in a series of Jacobi polynomials. Numerical solutions are obtained. It is shown that the stress field is independent of the electric field and the magnetic flux.

  8. The dynamic behavior of two collinear cracks in magneto-electro-elastic composites under harmonic anti-plane shear waves

    Institute of Scientific and Technical Information of China (English)

    SUN Yu-guo; WU Lin-zhi

    2005-01-01

    The dynamic behavior of two collinear cracks in magneto-electro-elastic composites under harmonic anti-plane shear waves is studied using the Schmidt method for the permeable crack surface conditions. By using the Fourier transform, the problem can be solved with a set of triple integral equations in which the unknown variable is the jump of the displacements across the crack surfaces. In solving the triple integral equations, the jump of the displacements across the crack surface is expanded in a series of Jacobi polynomials. It can be obtained that the stress field is independent of the electric field and the magnetic flux.

  9. An evaluation of the +/-45 deg tensile test for the determination of the in-plane shear strength of composite materials

    Science.gov (United States)

    Kellas, S.; Morton, J.; Jackson, K. E.

    1991-01-01

    The applicability of the +/-45 deg tensile test for the determination of the in-plane shear strength of advanced composite laminates is studied. The assumptions used for the development of the shear strength formulas were examined, and factors such as the specimen geometry and stacking sequence were assessed experimentally. It was found that the strength of symmetric and balanced +/-45 deg laminates depends primarily upon the specimen thickness rather than the specimen width. These findings have important implications for the +/-45 deg tensile test which is recommended by several organizations for the determination of the in-plane shear stress/strain response and the shear strength of continuous fiber reinforced composites. Modifications to the recommended practices for specimen selection and shear strength determination are suggested.

  10. Reflection and Transmission Coefficients for an Incident Plane Shear Wave at an Interface Separating Two Dissimilar Poroelastic Solids

    Science.gov (United States)

    Liu, Xu; Greenhalgh, Stewart

    2014-09-01

    Using Biot's poroelasticity theory, we derive expressions for the reflection and transmission coefficients for a plane shear wave incident on an interface separating two different poroelastic solids. The coefficients are formulated as a function of the wave incidence angle, frequency and rock properties. Specific cases calculated include the boundary between water-saturated sand and water-saturated sandstone and the gas-water interface in sand. The results show a very different interface response to that of an incident P wave. Plane SV wave incidence does not significantly excite the Biot slow P wave if the frequency of the wave is below the transition frequency. Above this frequency, an incident plane SV wave can generate a mode-converted slow Biot P wave which is actually a normal propagating wave and not highly attenuating as in the usual (diffusive) case. For an incident SV wave onto a gas-water interface, even at very high frequency, there is no significant Biot second P wave produced. For small incident angles, the gas-water interface is essentially transparent. With increasing angles, there can arise an unusual "definitive angle" in the reflection/transmission coefficient curves which is related to the change of fluid viscosity on both sides of the interface and provides a possible new means for underground fluid assessment.

  11. Calorimetry of non-reacting systems

    CERN Document Server

    McCullough, John P

    2013-01-01

    Experimental Thermodynamics, Volume 1: Calorimetry of Non-Reacting Systems covers the heat capacity determinations for chemical substances in the solid, liquid, solution, and vapor states, at temperatures ranging from near the absolute zero to the highest at which calorimetry is feasible.This book is divided into 14 chapters. The first four chapters provide background information and general principles applicable to all types of calorimetry of non-reacting systems. The remaining 10 chapters deal with specific types of calorimetry. Most of the types of calorimetry treated are developed over a c

  12. On the Nonlinear Stability of Plane Parallel Shear Flow in a Coplanar Magnetic Field

    Science.gov (United States)

    Xu, Lanxi; Lan, Wanli

    2016-10-01

    Lyapunov direct method has been used to study the nonlinear stability of laminar flow between two parallel planes in the presence of a coplanar magnetic field for streamwise perturbations with stress-free boundary planes. Two Lyapunov functions are defined. By means of the first, it is proved that the transverse components of the perturbations decay unconditionally and asymptotically to zero for all Reynolds numbers and magnetic Reynolds numbers. By means of the second, it is showed that the other components of the perturbations decay conditionally and exponentially to zero for all Reynolds numbers and the magnetic Reynolds numbers below π ^2/2M , where M is the maximum of the absolute value of the velocity field of the laminar flow.

  13. Off-plane motion of a non-spherical capsule in simple shear flow

    Science.gov (United States)

    Omori, Toshihiro; Ishikawa, Takuji; Imai, Yohsuke; Yamaguchi, Takami

    2012-11-01

    Dynamics of a capsule and a biological cell in fluid flow is now of great interest in chemical engineering and bioengineering. In this study, we numerically investigated the motion of a spheroid capsule in simple shear flow including a red blood cell type biconcave disk. The membrane of a capsule was modeled by a two-dimensional hyperelastic material, and its large deformation was solved by a finite element method. The motion of internal and external liquids was estimated as a Stokes flow and solved by a boundary element method. The results showed that the orientation of a spheroid capsule is variant under time reversal, though that of a rigid spheroid is invariant. The final orientation of a spheroid capsule over a long time duration tends to converge to a certain direction depending on the shear rate despite initial placement with random orientation. These results can be utilized for a particle alignment technique and form a fundamental basis of the suspension mechanics of capsules and biological cells.

  14. Coupling of bias-induced crystallographic shear planes with charged domain walls in ferroelectric oxide thin films

    Science.gov (United States)

    Han, Myung-Geun; Garlow, Joseph A.; Bugnet, Matthieu; Divilov, Simon; Marshall, Matthew S. J.; Wu, Lijun; Dawber, Matthew; Fernandez-Serra, Marivi; Botton, Gianluigi A.; Cheong, Sang-Wook; Walker, Frederick J.; Ahn, Charles H.; Zhu, Yimei

    2016-09-01

    Polar discontinuity at interfaces plays deterministic roles in charge transport, magnetism, and even superconductivity of functional oxides. To date, most polar discontinuity problems have been explored in heterointerfaces between two dissimilar materials. Here, we show that charged domain walls (CDWs) in epitaxial thin films of ferroelectric PbZ r0.2T i0.8O3 are strongly coupled to polar interfaces through the formation of 1/2 {h 0 l } - type crystallographic shear planes (CSPs). Using atomic resolution imaging and spectroscopy we illustrate that the CSPs consist of both conservative and nonconservative segments when coupled to the CDWs where necessary compensating charges for stabilizing the CDWs are associated with vacancies at the CSPs. The CDW/CSP coupling yields an atomically narrow domain wall, consisting of a single atomic layer of oxygen. This study shows that the CDW/CSP coupling is a fascinating venue to develop emergent material properties.

  15. Characterization of the Microstructure Evolution in IF-Steel and AA6016 during Plane-Strain Tension and Simple Shear.

    Science.gov (United States)

    Gerstein, Gregory; Klusemann, Benjamin; Bargmann, Swantje; Schaper, Mirko

    2015-01-15

    In the current work, the evolutions of grain and dislocation microstructures are investigated on the basis of plane strain tension and simple shear tests for an interstitial free steel (DC06) and a 6000 series aluminum alloy (AA6016-T4). Both materials are commonly-used materials in the automobile industry. The focus of this contribution is on the characterization and comparison of the microstructure formation in DC06 and AA6016-T4. Our observations shed light on the active mechanisms at the micro scale governing the macroscopic response. This knowledge is of great importance to understand the physical deformation mechanisms, allowing the control and design of new, tailor-made materials with the desired material behavior.

  16. SCATTERING OF ANTI-PLANE SHEAR WAVES IN A FUNCTIONALLY GRADED MATERIAL STRIP WITH AN OFF-CENTER VERTICAL CRACK

    Institute of Scientific and Technical Information of China (English)

    LI Lin; ZHOU Zhen-gong; WANG Biao

    2006-01-01

    The scattering problem of anti-plane shear waves in a functionally graded material strip with an off-center crack is investigated by use of Schmidt method. The crack is vertically to the edge of the strip. By using the Fourier transform, the problem can be solved with the help of a pair of dual integral equations that the unknown variable is the jump of the displacement across the crack surfaces. To solve the dual integral equations, the jump of the displacement across the crack surfaces was expanded in a series of Jacobi polynomials. Numerical examples were provided to show the effects of the parameter describing the functionally graded materials, the position of the crack and the frequency of the incident waves upon the stress intensity factors of the crack.

  17. Behavior of two parallel symmetry permeable cracks in functionally graded piezoelectric materials subjected to an anti-plane shear loading

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The behavior of two parallel symmetry permeable cracks in functionally graded piezoelectric materials subjected to an anti-plane shear loading was investigated. To make the analysis tractable, it was assumed that the material properties varied exponentially with coordinate vertical to the crack. By using the Fourier transform, the problem could be solved with the help of two pairs of dual integral equations, in which the unknown variables were the jumps of the displacements across the crack surfaces. To solve the dual integral equations, the displacement on the crack surfaces expanded in a series of Jacobi polynomials. The normalized stress and electrical displacement intensity factors were determined for different geometric and property parameters for permeable electric boundary conditions. Numerical examples were provided to show the effect of the geometry of the interacting cracks and the functionally graded material parameter upon the stress intensity factors of cracks.

  18. Boundary-dependent mechanical properties of graphene annular under in-plane circular shearing via atomistic simulations

    Science.gov (United States)

    Li, Yinfeng; Lin, Qianling; Cui, Daxiang

    2017-02-01

    Graphene annulus possesses special wrinkling phenomenon with wide range of potential applications. Using molecular dynamics simulation, this study concerns the effect of boundary on the mechanical properties of circular and elliptical graphene annuli under circular shearing at inner edge. Both the wrinkle characteristic and torque capacity of annular graphene can be effectively tuned by outer boundary radius and aspect ratio. For circular annulus with fixed inner radius, the critical angle of rotation can be increased by several times without sacrificing its torque capacity by increasing outer boundary radius. The wrinkle characteristic of graphene annulus with elliptical outer boundary differs markedly with that of circular annulus. Torque capacity anomalously decreases with the increase of aspect ratio, and a coupled effect of the boundary aspect ratio and the ratio of minor axis to inner radius on wrinkling are revealed. By studying the stress distribution and wrinkle characteristics, we find the decay of torque capacity is the result of circular stress concentration around the minor axis, while the nonuniform stress distribution is anomalously caused by the change of wrinkle profiles near the major axis. The specific mechanism of out-of-plane deformation on in-plane strength provides a straightforward means to develop novel graphene-based devices.

  19. Boundary-dependent mechanical properties of graphene annular under in-plane circular shearing via atomistic simulations

    Science.gov (United States)

    Li, Yinfeng; Lin, Qianling; Cui, Daxiang

    2017-01-01

    Graphene annulus possesses special wrinkling phenomenon with wide range of potential applications. Using molecular dynamics simulation, this study concerns the effect of boundary on the mechanical properties of circular and elliptical graphene annuli under circular shearing at inner edge. Both the wrinkle characteristic and torque capacity of annular graphene can be effectively tuned by outer boundary radius and aspect ratio. For circular annulus with fixed inner radius, the critical angle of rotation can be increased by several times without sacrificing its torque capacity by increasing outer boundary radius. The wrinkle characteristic of graphene annulus with elliptical outer boundary differs markedly with that of circular annulus. Torque capacity anomalously decreases with the increase of aspect ratio, and a coupled effect of the boundary aspect ratio and the ratio of minor axis to inner radius on wrinkling are revealed. By studying the stress distribution and wrinkle characteristics, we find the decay of torque capacity is the result of circular stress concentration around the minor axis, while the nonuniform stress distribution is anomalously caused by the change of wrinkle profiles near the major axis. The specific mechanism of out-of-plane deformation on in-plane strength provides a straightforward means to develop novel graphene-based devices. PMID:28198805

  20. Simultaneous quantitative evaluation of in-plane and out-of-plane deformation by use of a carrier method of large image-shearing shearography

    Institute of Scientific and Technical Information of China (English)

    Ping Sun; Ruijin Liu; Qing Han; Xiaofeng Wang

    2006-01-01

    A carrier method for separating out-of-plane displacement from in-plane components based on large imageshearing shearography is presented. A reference surface is fixed on the side of a test object. They are illuminated by two expanded symmetric illuminations respectively. The carrier is introduced by rotating the reference surface to modulate the displacement of an object. By using Fourier transform to demodulate the modulated fringe pattern, two phase maps, which include out-of-plane and in-plane displacements, can be obtained. Then the out-of-plane displacement can be easily separated from in-plane displacement by subtraction and addition of the two unwrapped phase distributions. The principle of the method is presented and proved by a typical three-point-bending experiment. Experimental results show that the method enjoys high visibility of carrier fringes. The system does not need a special beam as a reference light and has simple optical setup.

  1. Nonrashes. Part I: The Koebner nonreaction

    Energy Technology Data Exchange (ETDEWEB)

    Bernhard, J.D.; Haynes, H.A.

    1982-02-01

    ''Nonrashes'' range from pruritus that may signal an underlying systemic illness to delusional parasitosis associated with severe psychological disturbance. We report another kind of nonrash, the Koebner nonreaction or isomorphic nonresponse, that was manifested by the absence of a drug rash at the site of recently administered x-irradiation. We also present a compilation of a number of other nonrashes, such as the mitempfindungen (referred itch) and the prodrome of herpes zoster. The recognition of certain types of nonrashes may be lifesaving.

  2. Modeling fracture in the context of a strain-limiting theory of elasticity: a single anti-plane shear crack

    KAUST Repository

    Rajagopal, K. R.

    2011-01-06

    This paper is the first part of an extended program to develop a theory of fracture in the context of strain-limiting theories of elasticity. This program exploits a novel approach to modeling the mechanical response of elastic, that is non-dissipative, materials through implicit constitutive relations. The particular class of models studied here can also be viewed as arising from an explicit theory in which the displacement gradient is specified to be a nonlinear function of stress. This modeling construct generalizes the classical Cauchy and Green theories of elasticity which are included as special cases. It was conjectured that special forms of these implicit theories that limit strains to physically realistic maximum levels even for arbitrarily large stresses would be ideal for modeling fracture by offering a modeling paradigm that avoids the crack-tip strain singularities characteristic of classical fracture theories. The simplest fracture setting in which to explore this conjecture is anti-plane shear. It is demonstrated herein that for a specific choice of strain-limiting elasticity theory, crack-tip strains do indeed remain bounded. Moreover, the theory predicts a bounded stress field in the neighborhood of a crack-tip and a cusp-shaped opening displacement. The results confirm the conjecture that use of a strain limiting explicit theory in which the displacement gradient is given as a function of stress for modeling the bulk constitutive behavior obviates the necessity of introducing ad hoc modeling constructs such as crack-tip cohesive or process zones in order to correct the unphysical stress and strain singularities predicted by classical linear elastic fracture mechanics. © 2011 Springer Science+Business Media B.V.

  3. Tunnel effect of fractal fault and transient S-wave velocity rupture (TSVR) of in-plane shear fault

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    Transient S-wave velocity rupture (TSVR) means the velocity of fault rupture propagation is between S-wave velocity βand P-wave velocity α. Its existing in the rupture of in-plane (i.e. strike-slip) fault has been proved, but in 2-dimensional classical model, there are two difficulties in transient S-wave velocity rupture, i.e., initialization difficulty and divergence difficulty in interpreting the realization of TSVR. The initialization difficulty means, when v↑vR (Rayleigh wave velocity), the dynamic stress strength factor K2(t)→+0, and changes from positive into negative in the interval (vR,β). How v transit the forbidden of (vR,β)? The divergence difficulty means K2(t)→+ when v↓. Here we introduce the concept of fractal and tunnel effect that exist everywhere in fault. The structure of all the faults is fractal with multiple cracks. The velocity of fault rupture is differentiate of the length of the fault respect to time, so the rupture velocity is also fractal. The tunnel effect means the dynamic rupture crosses over the interval of the cracks, and the coalescence of the intervals is slower than the propagation of disturbance. Suppose the area of earthquake nucleation is critical or sub-critical propagation everywhere, the arriving of disturbance triggers or accelerates the propagation of cracks tip at once, and the observation system cannot distinguish the front of disturbance and the tip of fracture. Then the speed of disturbance may be identified as fracture velocity, and the phenomenon of TSVR appears, which is an apparent velocity. The real reason of apparent velocity is that the mathematics model of shear rupture is simplified of complex process originally. The dual character of rupture velocity means that the apparent velocity of fault and the real velocity of micro-crack extending, which are different in physics, but are unified in rupture criterion. Introducing the above-mentioned concept to the calculation of K2 (t), the difficulty of

  4. Behavior of fiber reinforced mortar joints in masonry walls subjected to in-plane shear and out-of-plane bending

    Science.gov (United States)

    Armwood, Catherine K.

    In this project, 26 fiber-reinforced mortar (FRM) mixtures are evaluated for their workability and strength characteristics. The specimens tested include two control mixtures and 24 FRMs. The mixtures were made of two types of binders; Type N Portland cement lime (Type N-PCL) and Natural Hydrated Lime 5 (NHL5); and 6 fiber types (5 synthetic fibers and one organic). When tested in flexure, the results indicate that majority of the synthetic fiber mixtures enhanced the performance of the mortar and the nano-nylon and horse hair fibers were the least effective in improving the mortar's modulus of rupture, ductility, and energy absorption. Four FRMs that improved the mortar's mechanical properties most during the flexural strength test were then used to conduct additional experiments. The FRM's compressive strength, as well as flexural and shear bond strength with clay and concrete masonry units were determined. Those four mixtures included Type N-PCL as the binder and 4 synthetic fibers. They were evaluated at a standard laboratory flow rate of 110% +/- 5% and a practical field flow rate of 130% +/- 5%. Results indicate that the use of fibers decreases the compressive strength of the mortar most of the time. However, the bond strength test results were promising: 81% of the FRM mixtures increased the flexural bond strength of the prism. The mixtures at 110 +/- 5% flow rate bonded better with concrete bricks and those ate 130+/-5% flow rate bonded better with clay bricks. The results of the shear bond strength show 50% of the FRM mixtures improved the shear bond strength. The FRM mixtures at 110+/-5% flow rate bonded with clay units provided the most improvement in shear bond strength compared to control specimen results. Along with detailed discussions and derived conclusions of these experiments, this dissertation includes recommendations for the most feasible FRM for different applications.

  5. Insights into the growth rate of spatially evolving plane turbulent free-shear layers from 2D vortex-gas simulations

    Science.gov (United States)

    Suryanarayanan, Saikishan; Narasimha, Roddam

    2017-02-01

    Although the free-shear or mixing layer has been a subject of extensive research over nearly a century, there are certain fundamental issues that remain controversial. These include the influence of initial and downstream conditions on the flow, the effect of velocity ratio across the layer, and the nature of any possible coupling between small scale dynamics and the large scale evolution of layer thickness. In the spirit of the temporal vortex-gas simulations of Suryanarayanan et al. ["Free turbulent shear layer in a point vortex gas as a problem in nonequilibrium statistical mechanics," Phys. Rev. E 89, 013009 (2014)], we revisit the simple 2D inviscid vortex-gas model with extensive computations and detailed analysis, in order to gain insights into some of the above issues. Simulations of the spatially evolving vortex-gas shear layer are carried out at different velocity ratios using a computational model based on the work of Basu et al. ["Vortex sheet simulation of a plane canonical mixing layer," Comput. Fluids 21, 1-30 (1992) and "Modelling plane mixing layers using vortex points and sheets," Appl. Math. Modell. 19, 66-75 (1995)], but with a crucial improvement that ensures conservation of global circulation. The simulations show that the conditions imposed at the origin of the free shear layer and at the exit to the computational domain can affect flow evolution in their respective downstream and upstream neighbourhoods, the latter being particularly strong in the single stream limit. In between these neighbourhoods at the ends is a regime of universal self-preserving growth rate given by a universal function of velocity ratio. The computed growth rates are generally located within the scatter of experimental data on plane mixing layers and closely agree with recent high Reynolds number experiments and 3D large eddy simulation studies. These findings support the view that observed free-shear layer growth can be largely explained by the 2D vortex dynamics of

  6. Piezoelectric d36 in-plane shear-mode of lead-free BZT-BCT single crystals for torsion actuation

    Science.gov (United States)

    Berik, P.; Chang, W.-Y.; Jiang, X.

    2017-01-01

    We report the study of piezoelectric direct torsion actuation mechanism using lead-free piezoelectric d36 in-plane shear-mode BZT-BCT single crystals. The generated angle of twist of the piezoelectric torsion actuator was obtained from the transverse deflection measurement using a laser vibrometer. The bi-morph torsional actuator, consisting of two lead-free piezoelectric BZT-BCT in-plane shear-mode single crystals with a giant piezoelectric d36 shear strain coefficient of 1590 pC/N, provided a rate of twist of 34.12 mm/m under a quasi-static 15 V drive. The experimental benchmark was further modelled and verified by the ANSYS software using three dimensional (3D) piezoelectric finite elements. The experimental results revealed that lead-free piezoelectric BZT-BCT d36-mode single crystal is a superior candidate for piezoelectric torsion actuation. This lead-free piezoelectric BZT-BCT d36-mode torsion actuator can be effectively applied in torsional deformation control by taking into account the environmental considerations.

  7. INVESTIGATION OF THE DYNAMIC BEHAVIOR OF TWO COLLINEAR ANTI-PLANE SHEAR CRACKS IN A PIEZOELECTRIC LAYER BONDED TO TWO HALF SPACES BY A NEW METOHD

    Institute of Scientific and Technical Information of China (English)

    周振功; 王彪

    2003-01-01

    The dynamic behavior of two collinear anti-plane shear cracks in a piezoelectriclayer bonded to two half spaces subjected to the harmonic waves is investigated by a newmethod. The cracks are parallel to the interfaces in the mid-plane of the piezoelectric layer.By using the Fourier transform, the problem can be solved with two pairs of triple integralequations. These equations are solved by using Schmidt's method. This process is quitedifferent from that adopted previously. Numerical examples are provided to show the effectof the geometry of cracks, the frequency of the incident wave, the thickness of thepiezoelectric layer and the constants of the materials upon the dynamic stress intensity factorof cracks.

  8. Turbulent Transport by Diffusive Stratified Shear Flows: From Local to Global Models. I. Numerical Simulations of a Stratified Plane Couette Flow

    Science.gov (United States)

    Garaud, Pascale; Gagnier, Damien; Verhoeven, Jan

    2017-03-01

    Shear-induced turbulence could play a significant role in mixing momentum and chemical species in stellar radiation zones, as discussed by Zahn. In this paper we analyze the results of direct numerical simulations of stratified plane Couette flows, in the limit of rapid thermal diffusion, to measure the turbulent viscosity and the turbulent diffusivity of a passive tracer as a function of the local shear and the local stratification. We find that the stability criterion proposed by Zahn, namely that the product of the gradient Richardson number and the Prandtl number must be smaller than a critical values {(J\\Pr )}c for instability, adequately accounts for the transition to turbulence in the flow, with {(J\\Pr )}c≃ 0.007. This result recovers and confirms the prior findings of Prat et al. Zahn’s model for the turbulent diffusivity and viscosity, namely that the mixing coefficient should be proportional to the ratio of the thermal diffusivity to the gradient Richardson number, does not satisfactorily match our numerical data. It fails (as expected) in the limit of large stratification where the Richardson number exceeds the aforementioned threshold for instability, but it also fails in the limit of low stratification where the turbulent eddy scale becomes limited by the computational domain size. We propose a revised model for turbulent mixing by diffusive stratified shear instabilities that properly accounts for both limits, fits our data satisfactorily, and recovers Zahn’s model in the limit of large Reynolds numbers.

  9. Stability and turbulent transport in rotating shear flows: prescription from analysis of cylindrical and plane Couette flows data

    CERN Document Server

    Dubrulle, B; Daviaud, F; Longaretti, P-Y; Richard, D; Zahn, J-P

    2011-01-01

    This paper provides a prescription for the turbulent viscosity in rotating shear flows for use e.g. in geophysical and astrophysical contexts. This prescription is the result of the detailed analysis of the experimental data obtained in several studies of the transition to turbulence and turbulent transport in Taylor-Couette flow. We first introduce a new set of control parameters, based on dynamical rather than geometrical considerations, so that the analysis applies more naturally to rotating shear flows in general and not only to Taylor-Couette flow. We then investigate the transition thresholds in the supercritical and the subcritical regime in order to extract their general dependencies on the control parameters. The inspection of the mean profiles provides us with some general hints on the mean to laminar shear ratio. Then the examination of the torque data allows us to propose a decomposition of the torque dependence on the control parameters in two terms, one completely given by measurements in the ca...

  10. Steel plates and concrete filled composite shear walls related nuclear structural engineering: Experimental study for out-of-plane cyclic loading

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xiaohu [The College of Architecture and Civil Engineering, Beijing University of Technology, Beijing 100124 (China); Li, Xiaojun, E-mail: beerli@vip.sina.com [The College of Architecture and Civil Engineering, Beijing University of Technology, Beijing 100124 (China); Institute of Geophysics, China Earthquake Administration, Beijing 100081 (China)

    2017-04-15

    Based on the program of CAP1400 nuclear structural engineering, the out-of-plane seismic behavior of steel plate and concrete infill composite shear walls (SCW) was investigated. 6 1/5 scaled specimens were conducted which consist of 5 SCW specimens and 1 reinforced concrete (RC) specimen. The specimens were tested under out-of-plane cyclic loading. The effect of the thickness of steel plate, vertical load and the strength grade of concrete on the out-of-plane seismic behavior of SCW were analyzed. The results show that the thickness of steel plate and vertical load have great influence on the ultimate bearing capacity and lateral stiffness, however, the influence of the strength grade of concrete was little within a certain range. SCW is presented to have a better ultimate capacity and lateral stiffness but have worse ductility in failure stage than that of RC. Based on the experiment, the cracking load of concrete infill SCW was analyzed in theory. The modified calculation formula of the cracking load was made, the calculated results showed good agreement with the test results. The formula can be used as the practical design for the design of cracking loads.

  11. Out-of-plane (SH) soil-structure interaction: a shear wall with rigid and flexible ring foundation

    Science.gov (United States)

    Le, Thang; Lee, Vincent W.; Luo, Hao

    2016-02-01

    Soil-structure interaction (SSI) of a building and shear wall above a foundation in an elastic half-space has long been an important research subject for earthquake engineers and strong-motion seismologists. Numerous papers have been published since the early 1970s; however, very few of these papers have analytic closed-form solutions available. The soil-structure interaction problem is one of the most classic problems connecting the two disciplines of earthquake engineering and civil engineering. The interaction effect represents the mechanism of energy transfer and dissipation among the elements of the dynamic system, namely the soil subgrade, foundation, and superstructure. This interaction effect is important across many structure, foundation, and subgrade types but is most pronounced when a rigid superstructure is founded on a relatively soft lower foundation and subgrade. This effect may only be ignored when the subgrade is much harder than a flexible superstructure: for instance a flexible moment frame superstructure founded on a thin compacted soil layer on top of very stiff bedrock below. This paper will study the interaction effect of the subgrade and the superstructure. The analytical solution of the interaction of a shear wall, flexible-rigid foundation, and an elastic half-space is derived for incident SH waves with various angles of incidence. It found that the flexible ring (soft layer) cannot be used as an isolation mechanism to decouple a superstructure from its substructure resting on a shaking half-space.

  12. SCATTERING OF ANTI-PLANE SHEAR WAVES BY A SINGLE CRACK IN AN UNBOUNDED TRANSVERSELY ISOTROPIC ELECTRO-MAGNETO-ELASTIC MEDIUM

    Institute of Scientific and Technical Information of China (English)

    杜建科; 沈亚鹏; 高波

    2004-01-01

    A theoretical treatment of the scattering of anti-plane shear (SH) waves is provided by a single crack in an unbounded transversely isotropic electro-magneto-elastic medium. Based on the differential equations of equilibrium, electric displacement and magnetic induction intensity differential equations, the governing equations for SH waves were obtained. By means of a linear transform, the governing equations were reduced to one Helmholtz and two Laplace equations. The Cauchy singular integral equations were gained by making use of Fourier transform and adopting electro-magneto impermeable boundary conditions. The closed form expression for the resulting stress intensity factor at the crack was achieved by solving the appropriate singular integral equations using Chebyshev polynomial. Typical examples are provided to show the loading frequency upon the local stress fields around the crack tips. The study reveals the importance of the electromagneto-mechanical coupling terms upon the resulting dynamic stress intensity factor.

  13. ON ANTI-PLANE SHEAR BEHAVIOR OF A GRIFFITH PERMEABLE CRACK IN PIEZOELECTRIC MATERIALS BY USE OF THE NON-LOCAL THEORY

    Institute of Scientific and Technical Information of China (English)

    周振功; 杜善义; 王彪

    2003-01-01

    In this paper, the non-local theory of elasticity is applied to obtain the behavior of a Griffith crack in the piezoelectric materials under anti-plane shear loading for permeable crack surface conditions. By means of the Fourier transform, the problem can be solved with the help of a pair of dual integral equations with the unknown variable being the jump of the displacement across the crack surfaces. These equations are solved by the Schmidt method. Numerical examples are provided.Unlike the classical elasticity solutions, it is found that no stress and electric displacement singularity is present at the crack tip. The non-local elastic solutions yield a finite hoop stress at the crack tip,thus allowing for a fracture criterion based on the maximum stress hypothesis. The finite hoop stress at the crack tip depends on the crack length and the lattice parameter of the materials, respectively.

  14. Non-local dynamic solution of two parallel cracks in a functionally graded piezoelectric material under harmonic anti-plane shear wave

    Science.gov (United States)

    Liu, Hai-Tao; Sang, Jian-Bing; Zhou, Zhen-Gong

    2016-10-01

    This paper investigates a functionally graded piezoelectric material (FGPM) containing two parallel cracks under harmonic anti-plane shear stress wave based on the non-local theory. The electric permeable boundary condition is considered. To overcome the mathematical difficulty, a one-dimensional non-local kernel is used instead of a two-dimensional one for the dynamic fracture problem to obtain the stress and the electric displacement fields near the crack tips. The problem is formulated through Fourier transform into two pairs of dual-integral equations, in which the unknown variables are jumps of displacements across the crack surfaces. Different from the classical solutions, that the present solution exhibits no stress and electric displacement singularities at the crack tips.

  15. Turbulent transport by diffusive stratified shear flows: from local to global models. Part I: Numerical simulations of a stratified plane Couette flow

    CERN Document Server

    Garaud, P; Verhoeven, J

    2016-01-01

    Shear-induced turbulence could play a significant role in mixing momentum and chemical species in stellar radiation zones, as discussed by Zahn (1974). In this paper we analyze the results of direct numerical simulations of stratified plane Couette flows, in the limit of rapid thermal diffusion, to measure the turbulent diffusivity and turbulent viscosity as a function of the local shear and the local stratification. We find that the stability criterion proposed by Zahn (1974), namely that the product of the gradient Richardson number and the Prandtl number must be smaller than a critical values $(J\\Pr)_c$ for instability, adequately accounts for the transition to turbulence in the flow, with $(J\\Pr)_c \\simeq 0.007$. This result recovers and confirms the prior findings of Prat et al. (2016). Zahn's model for the turbulent diffusivity and viscosity (Zahn 1992), namely that the mixing coefficient should be proportional to the ratio of the thermal diffusivity to the gradient Richardson number, does not satisfact...

  16. Particle-in-cell simulation study of the scaling of asymmetric magnetic reconnection with in-plane flow shear

    CERN Document Server

    Doss, C E; Swisdak, M

    2016-01-01

    We investigate magnetic reconnection in systems simultaneously containing asymmetric (anti-parallel) magnetic fields, asymmetric plasma densities and temperatures, and arbitrary in-plane bulk flow of plasma in the upstream regions. Such configurations are common in the high-latitudes of Earth's magnetopause and in tokamaks. We investigate the convection speed of the X-line, the scaling of the reconnection rate, and the condition for which the flow suppresses reconnection as a function of upstream flow speeds. We use two-dimensional particle-in-cell simulations to capture the mixing of plasma in the outflow regions better than is possible in fluid modeling. We perform simulations with asymmetric magnetic fields, simulations with asymmetric densities, and simulations with magnetopause-like parameters where both are asymmetric. For flow speeds below the predicted cutoff velocity, we find good scaling agreement with the theory presented in Doss et al., J.~Geophys.~Res., 120, 7748 (2015). Applications to planetary...

  17. The nonlocal solution of two parallel cracks in functionally graded materials subjected to harmonic anti-plane shear waves

    Institute of Scientific and Technical Information of China (English)

    Jun Liang; Shiping Wu; Shanyi Du

    2007-01-01

    In this paper, the dynamic interaction of two parallel cracks in functionally graded materials (FGMs) is investigated by means of the non-local theory. To make the analysis tractable, the shear modulus and the material den-sity are assumed to vary exponentially with the coordinate vertical to the crack. To reduce mathematical difficulties, a one-dimensional non-local kemel is used instead of a two-dimensional one for the dynamic problem to obtain stress fields near the crack tips. By use of the Fourier transform,the problem can be solved with the help of two pairs of dual integral equations, in which the unknown variables are the jumps of displacements across the crack surfaces. To solve the dual integral equations, the jumps of displace-ments across the crack surfaces are expanded in a series of Jacobi polynomials. Unlike the classical elasticity solu-tions, it is found that no stress singularity is present at the crack tips. The non-local elastic solutions yield a finite hoop stress at the crack tips. The present result provides theoret-ical references helpful for evaluating relevant strength and preventing material failure of FGMs with initial cracks. The magnitude of the finite stress field depends on relevant param-eters, such as the crack length, the distance between two parallel cracks, the parameter describing the FGMs, the fre-quency of the incident waves and the lattice parameter of materials.

  18. Turbulent shear flow downstream of a sphere with and without an o-ring located over a plane boundary

    Directory of Open Access Journals (Sweden)

    Sahin Besir

    2012-04-01

    Full Text Available Flow-structure interaction of separated shear flow from the sphere and a flat plate was investigated by using dye visualization and the particle image velocimetry technique. Later, a passive control method was applied with 2mm oring located on the sphere surface at 55° from front stagnation point. The experiments were carried out in open water channel for Reynolds number value of Re=5000. Flow characteristics have been examined in terms of the 2-D instantaneous and time-averaged velocity vectors, patterns of vorticity, streamlines, rms of velocity fluctuations and Reynolds stress variations and discussed from the point of flow physics, vortex formation, lengths of large-scale Karman Vortex Streets and Kelvin-Helmholtz vortices depending on the sphere locations over the flat plate. It is demonstrated that the gap flow occurring between the sphere bottom point and the flat plate surface has very high scouring effect until h/d=0.25 and then unsymmetrical flow structure of the wake region keeps up to h/D=1.0 for smooth sphere. For the sphere with o-ring, the wake flow structure becomes symmetrical at smaller gap ratios and reattachment point on the flat plate surface occurs earlier. Moreover, o-ring on the sphere diminishes peak magnitudes of the flow characteristics and thus it is expected that the flow-induced forces will be lessened both on the sphere and flat plate surface. Vortex formation lengths and maximum value occurring points become closer locations to the rear surface of the sphere with o-ring.

  19. Turbulent shear flow downstream of a sphere with and without an o-ring located over a plane boundary

    Science.gov (United States)

    Ozgoren, Muammer; Okbaz, Abdulkerim; Dogan, Sercan; Sahin, Besir; Akilli, Huseyin

    2012-04-01

    Flow-structure interaction of separated shear flow from the sphere and a flat plate was investigated by using dye visualization and the particle image velocimetry technique. Later, a passive control method was applied with 2mm oring located on the sphere surface at 55° from front stagnation point. The experiments were carried out in open water channel for Reynolds number value of Re=5000. Flow characteristics have been examined in terms of the 2-D instantaneous and time-averaged velocity vectors, patterns of vorticity, streamlines, rms of velocity fluctuations and Reynolds stress variations and discussed from the point of flow physics, vortex formation, lengths of large-scale Karman Vortex Streets and Kelvin-Helmholtz vortices depending on the sphere locations over the flat plate. It is demonstrated that the gap flow occurring between the sphere bottom point and the flat plate surface has very high scouring effect until h/d=0.25 and then unsymmetrical flow structure of the wake region keeps up to h/D=1.0 for smooth sphere. For the sphere with o-ring, the wake flow structure becomes symmetrical at smaller gap ratios and reattachment point on the flat plate surface occurs earlier. Moreover, o-ring on the sphere diminishes peak magnitudes of the flow characteristics and thus it is expected that the flow-induced forces will be lessened both on the sphere and flat plate surface. Vortex formation lengths and maximum value occurring points become closer locations to the rear surface of the sphere with o-ring.

  20. Turbulent mixing in nonreactive and reactive flows

    CERN Document Server

    1975-01-01

    Turbulence, mixing and the mutual interaction of turbulence and chemistry continue to remain perplexing and impregnable in the fron­ tiers of fluid mechanics. The past ten years have brought enormous advances in computers and computational techniques on the one hand and in measurements and data processing on the other. The impact of such capabilities has led to a revolution both in the understanding of the structure of turbulence as well as in the predictive methods for application in technology. The early ideas on turbulence being an array of complicated phenomena and having some form of reasonably strong coherent struc­ ture have become well substantiated in recent experimental work. We are still at the very beginning of understanding all of the aspects of such coherence and of the possibilities of incorporating such structure into the analytical models for even those cases where the thin shear layer approximation may be valid. Nevertheless a distinguished body of "eddy chasers" has come into existence. T...

  1. Congenital syphilis in neonates with nonreactive nontreponemal test results.

    Science.gov (United States)

    Wozniak, P S; Cantey, J B; Zeray, F; Leos, N K; Sheffield, J S; Wendel, G D; Sánchez, P J

    2017-07-06

    Infants whose mothers had syphilis during pregnancy were studied to determine how often exposed newborns with normal physical examinations and nonreactive nontreponemal serologic tests had abnormal laboratory or radiographic studies. Retrospective analysis of prospectively collected data from infants born to mothers with syphilis and had a normal examination and a nonreactive nontreponemal test. Some infants had IgM immunoblotting, PCR testing or rabbit infectivity testing (RIT) performed. From 1984 to 2002, 115 infants had a nonreactive serum Venereal Disease Research Laboratory (VDRL)/rapid plasma reagin (RPR) test and a normal physical examination at birth. Among 87 infants born to mothers who had untreated syphilis, 4 had a positive serum IgM immunoblot or PCR test, but none had spirochetes recovered by RIT. Two infants had anemia, one had an elevated serum alanine aminotransferase concentration and one with Down's syndrome had direct hyperbilirubinemia. Among 14 infants born to mothers treated laboratory or radiographic tests, although 1 of 11 had a reactive serum IgM immunoblot. Among 14 infants born to mothers treated ⩾4 weeks before delivery, none had abnormal laboratory or radiographic tests. Newborns with normal physical examination and nonreactive nontreponemal test results are unlikely to have abnormalities detected on conventional laboratory and radiographic testing.Journal of Perinatology advance online publication, 6 July 2017; doi:10.1038/jp.2017.103.

  2. Large Eddy Simulation of Sydney Swirl Non-Reaction Jets

    DEFF Research Database (Denmark)

    Yang, Yang; Kær, Søren Knudsen; Yin, Chungen

    The Sydney swirl burner non-reaction case was studied using large eddy simulation. The two-point correlation method was introduced and used to estimate grid resolution. Energy spectra and instantaneous pressure and velocity plots were used to identify features in flow field. By using these method...

  3. Cutaneous tuberculosis with nonreactive PPD skin test: a diagnostic challenge.

    Science.gov (United States)

    Nassif, Priscila Wolf; Rosa, Ana Paula Zanatta; Gurgel, Ana Cristina Medeiros; Campanerut, Paula Aline Zanetti; Fillus Neto, José; Cardoso, Rosilene Fressatti

    2015-01-01

    The authors report a case of cutaneous tuberculosis in a 63-year-old female patient, who had an infiltrated, erythematous-ferruginous plaque of indurated aspect on her right leg and a nonreactive PPD skin test. Diagnosis was made by tissue culture and PCR of skin biopsy material. The treatment was performed with pyrazinamide, rifampicin, isoniazid and ethambutol, with good response.

  4. An experimental investigation of reacting and nonreacting coaxial jet mixing in a laboratory rocket engine

    Science.gov (United States)

    Schumaker, Stephen Alexander

    Coaxial jets are commonly used as injectors in propulsion and combustion devices due to both the simplicity of their geometry and the rapid mixing they provide. In liquid rocket engines it is common to use coaxial jets in the context of airblast atomization. However, interest exists in developing rocket engines using a full flow staged combustion cycle. In such a configuration both propellants are injected in the gaseous phase. In addition, gaseous coaxial jets have been identified as an ideal test case for the validation of the next generation of injector modeling tools. For these reasons an understanding of the fundamental phenomena which govern mixing in gaseous coaxial jets and the effect of combustion on these phenomena in coaxial jet diffusion flames is needed. A study was performed to better understand the scaling of the stoichiometric mixing length in reacting and nonreacting coaxial jets with velocity ratios greater than one and density ratios less than one. A facility was developed that incorporates a single shear coaxial injector in a laboratory rocket engine capable of ten atmospheres. Optical access allows the use of flame luminosity and laser diagnostic techniques such as Planar Laser Induced Fluorescence (PLIF). Stoichiometric mixing lengths (LS), which are defined as the distance along the centerline where the stoichiometric condition occurs, were measured using PLIF. Acetone was seeded into the center jet to provide direct PLIF measurement of the average and instantaneous mixture fraction fields for a range of momentum flux ratios for the nonreacting cases. For the coaxial jet diffusion flames, LS was measured from OH radical contours. For nonreacting cases the use of a nondimensional momentum flux ratio was found to collapse the mixing length data. The flame lengths of coaxial jet diffusion flames were also found to scale with the momentum flux ratio but different scaling constants are required which depended on the chemistry of the reaction. The

  5. The non-local theory solution of a Griffith crack in functionally graded materials subjected to the harmonic anti-plane shear waves

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In this paper, the dynamic stress field near crack tips in the functionally graded materials subjected to the harmonic anti-plane shear stress waves was investi- gated by means of the non-local theory. The traditional concepts of the non-local theory were extended to solve the fracture problem of functionally graded materials. To make the analysis tractable, it was assumed that the material properties vary exponentially with coordinate parallel to the crack. By use of the Fourier transform, the problem can be solved with the help of a pair of dual integral equations, in which the unknown variable was the displacement on the crack surfaces. To solve the dual integral equations, the displacement on the crack surfaces was expanded in a series of Jacobi polynomials. Unlike the classical elasticity solutions, it is found that no stress singularities are present at crack tips. The non-local elastic solutions yield a finite hoop stress at crack tips, thus allowing us to use the maximum stress as a fracture criterion. The magnitude of the finite dynamic stress field depends on the crack length, the parameter describing the functionally graded materials, the circular frequency of the incident waves and the lattice parameter of materials.

  6. The non-local theory solution of a Griffith crack in functionally graded materials subjected to the harmonic anti-plane shear waves

    Institute of Scientific and Technical Information of China (English)

    ZHANG PeiWei; ZHOU ZhenGong; WU LinZhi

    2007-01-01

    In this paper, the dynamic stress field near crack tips in the functionally graded materials subjected to the harmonic anti-plane shear stress waves was investigated by means of the non-local theory. The traditional concepts of the non-local theory were extended to solve the fracture problem of functionally graded materials.To make the analysis tractable, it was assumed that the material properties vary exponentially with coordinate parallel to the crack. By use of the Fourier transform,the problem can be solved with the help of a pair of dual integral equations, in which the unknown variable was the displacement on the crack surfaces. To solve the dual integral equations, the displacement on the crack surfaces was expanded in a series of Jacobi polynomials. Unlike the classical elasticity solutions, it is found that no stress singularities are present at crack tips. The non-local elastic solutions yield a finite hoop stress at crack tips, thus allowing us to use the maximum stress as a fracture criterion. The magnitude of the finite dynamic stress field depends on the crack length, the parameter describing the functionally graded materials, the circular frequency of the incident waves and the lattice parameter of materials.

  7. Experimental thermodynamics experimental thermodynamics of non-reacting fluids

    CERN Document Server

    Neindre, B Le

    2013-01-01

    Experimental Thermodynamics, Volume II: Experimental Thermodynamics of Non-reacting Fluids focuses on experimental methods and procedures in the study of thermophysical properties of fluids. The selection first offers information on methods used in measuring thermodynamic properties and tests, including physical quantities and symbols for physical quantities, thermodynamic definitions, and definition of activities and related quantities. The text also describes reference materials for thermometric fixed points, temperature measurement under pressures, and pressure measurements. The publicatio

  8. Rayleigh-wave phase-velocity maps and three-dimensional shear velocity structure of the western US from local non-plane surface wave tomography

    Science.gov (United States)

    Pollitz, F.F.; Snoke, J. Arthur

    2010-01-01

    We utilize two-and-three-quarter years of vertical-component recordings made by the Transportable Array (TA) component of Earthscope to constrain three-dimensional (3-D) seismic shear wave velocity structure in the upper 200 km of the western United States. Single-taper spectral estimation is used to compile measurements of complex spectral amplitudes from 44 317 seismograms generated by 123 teleseismic events. In the first step employed to determine the Rayleigh-wave phase-velocity structure, we implement a new tomographic method, which is simpler and more robust than scattering-based methods (e.g. multi-plane surface wave tomography). The TA is effectively implemented as a large number of local arrays by defining a horizontal Gaussian smoothing distance that weights observations near a given target point. The complex spectral-amplitude measurements are interpreted with the spherical Helmholtz equation using local observations about a succession of target points, resulting in Rayleigh-wave phase-velocity maps at periods over the range of 18–125 s. The derived maps depend on the form of local fits to the Helmholtz equation, which generally involve the nonplane-wave solutions of Friederich et al. In a second step, the phase-velocity maps are used to derive 3-D shear velocity structure. The 3-D velocity images confirm details witnessed in prior body-wave and surface-wave studies and reveal new structures, including a deep (>100 km deep) high-velocity lineament, of width ∼200 km, stretching from the southern Great Valley to northern Utah that may be a relic of plate subduction or, alternatively, either a remnant of the Mojave Precambrian Province or a mantle downwelling. Mantle seismic velocity is highly correlated with heat flow, Holocene volcanism, elastic plate thickness and seismicity. This suggests that shallow mantle structure provides the heat source for associated magmatism, as well as thinning of the thermal lithosphere, leading to relatively high

  9. Non-partial wave treatment of reactive and non-reactive scattering Coupled integral equation formalism.

    Science.gov (United States)

    Hayes, E. F.; Kouri, D. J.

    1971-01-01

    Coupled integral equations are derived for the full scattering amplitudes for both reactive and nonreactive channels. The equations do not involve any partial wave expansion and are obtained using channel operators for reactive and nonreactive collisions. These coupled integral equations are similar in nature to equations derived for purely nonreactive collisions of structureless particles. Using numerical quadrature techniques, these equations may be reduced to simultaneous algebraic equations which may then be solved.

  10. Flash pryolysis of biomass with reactive and nonreactive gases

    Science.gov (United States)

    Sundaram, M. S.; Steinberg, M.; Fallon, P. T.

    1982-10-01

    Studies were done on the flash pyrolysis of Douglas Fir wood in the presence of reactive and nonreactive gases including hydrogen, methane, and helium. Pyrolysis and gasification of the wood particles was done in one step, without catalysts. Almost complete (98%) gasification of the carbon in Douglas fir wood was achieved at 10000C and 500-psi hydrogen pressure. The reaction products were methane, ethane, ethylene, carbon monoxide, BTX, and water. Flash hydropyrolysis produced a large yield of hydrocarbon gases (up to 78% C) comprising methane and ethane. High yields of ethylene (up to 21% C) and BTX (up to 12% C) were obtained via methane pyrolysis of fir wood; a free radical mechanism is proposed to explain the enhanced yield of ethylene in a methane atmosphere.

  11. Non-Reactive Shear-Coaxial Jets with and without Transverse Acoustic Forcing

    Science.gov (United States)

    2012-04-23

    Orthogonal Decomposition Technique • Eigenvalue decomposition or singular value decomposition ( SVD ) can be used • SVD preferred since 1. Applicable...mean of A matrix of intensity fluctuations à • Applied SVD TT QVUSVà N × N Orthogonal Matrix of Left Singular Column Vectors of à N × P Orthogonal...characterized by antisymmetric flow structures that indicated the presence of helical instabilities peak frequencies of the magnitude spectra became broader

  12. Droplet Combustion and Non-Reactive Shear-Coaxial Jets with and without Transverse Acoustic Excitation

    Science.gov (United States)

    2012-01-01

    Teshome is approved. Russel E. Caflisch Xiaolin Zhong Ivett A. Leyva Owen I. Smith, Committee Co-chair Ann R. Karagozian, Committee Co-chair University of...Schadow, E. Gutmark, T.P. Parr , D.M. Parr , K.J. Wilson, and J.E. Crump. Large-scale coherent structures as drivers of combustion instability

  13. Droplet Combustion and Non-Reactive Shear-Coaxial Jets with Transverse Acoustic Excitation

    Science.gov (United States)

    2012-06-01

    Ao/Ai, large t/D1 injector showed strong response at the forcing frequency. iv The dissertation of Sophonias Teshome is approved. Russel E. Caflisch...Professor Xiaolin Zhong and Professor Russel Caflisch are very much appreciated. I would like to recognize current and former lab colleagues including...Reardon. Liquid propellant rocket combustion instability. nasa sp-194. NASA Special Publication, 194, 1972. [26] K.C. Schadow, E. Gutmark, T.P. Parr

  14. Acoustic excitation of diffusion flames with coherent structure in a plane shear layer.; Effects of acoustic excitation on combustion properties; Soshiki kozo wo tomonau sendan kakusan kaen no onkyo reiki.; Onkyo reiki ni yoru nensho tokusei no henka

    Energy Technology Data Exchange (ETDEWEB)

    Ishino, Y.; Kojima, T.; Oiwa, N.; Yamaguchi, S. [Nagoya Institute of Technology, Nagoya (Japan)

    1993-10-25

    This paper reports on experiments for acoustic excitation of plane shear structured flame. Flows of air separated into the higher velocity side and the lower velocity side by a partition on the center of a flow path merge at the measuring point to form a mixed layer with coherent structure. Fuel is supplied to this mixed layer with the flows so adjusted that the generated flame will attach to the partition on the lower velocity side. Acoustic excitation (at a sound pressure level of 100 dB to 120 dB) is performed in a speaker fitted on a wall on the higher velocity side. The paper mentions the results of the experiments as follows: the acoustic excitation produces such changes to diffusion flame in the plane shear layer as shorter flame and blue flame combustion and clarification of flame structures; as seen from spectral characteristics of temperature change in the flames, a flame acoustically excited strongly presents remarkable improvements in periodicity of the structure; as seen from sound pressure distribution in the flow direction at the measuring point, the flame zone of the flame acoustically excited strongly is positioned at the middle of the node and loop of a standing wave. 6 refs., 9 figs., 1 tab.

  15. Design and Manufacturing of a Novel Shear Thickening Fluid Composite (STFC) with Enhanced out-of-Plane Properties and Damage Suppression

    Science.gov (United States)

    Pinto, F.; Meo, M.

    2016-09-01

    The ability to absorb a large amount of energy during an impact event without generating critical damages represents a key feature of new generation composite systems. Indeed, the intrinsic layered nature of composite materials allows the embodiment of specific hybrid plies within the stacking sequence that can be exploited to increase impact resistance and damping of the entire structure without dramatic weight increase. This work is based on the development of an impact-resistant hybrid composite obtained by including a thin layer of Non-Newtonian silica based fluid in a carbon fibres reinforced polymer (CFRP) laminate. This hybrid phase is able to respond to an external solicitation by activating an order-disorder transition that thickens the fluid increasing its viscosity, hence dissipating the energy impact without any critical failure. Several Shear Thickening Fluids (STFs) were manufactured by changing the dimensions of the particles that constitute the disperse phase and their concentrations into the continuous phase. The dynamic viscosity of the different STFs was evaluated via rheometric tests, observing both shear thinning and shear thickening effects depending on the concentration of silica particles. The solutions were then embedded as an active layer within the stacking sequence to manufacture the hybrid CFRP laminates with different embedded STFs. Free vibration tests were carried out in order to assess the damping properties of the different laminates, while low velocity impact tests were used to evaluate their impact properties. Results indicate that the presence of the non-Newtonian fluid is able to absorb up to 45 % of the energy during an impact event for impacts at 2.5 m/s depending on the different concentrations and particles dimensions. These results were confirmed via C-Scan analyses to assess the extent of the internal delamination.

  16. 基于临界面法的剪切式多轴疲劳寿命预测模型%A MULTIAXIAL FATIGUE LIFE PREDICTION MODEL WITH SHEAR FORM BASED ON THE CRITICAL PLANE APPROACH

    Institute of Scientific and Technical Information of China (English)

    刘嘉; 李静; 张忠平

    2012-01-01

    Based on the critical plane approach,a new multiaxial fatigue damage parameter with shear form is proposed by means of the von-Mises criterion. This proposed damage parameter is suitable for both proportional and non-proportional loading. Besides, this damage parameter considers the maximum shear strain range and the normal strain range on the critical plane. The effect of the non-proportional cyclic hardening on the fatigue life is taken into account by an introduced stress-correlated factor. It is convenient for engineering application because of no empirical constants in this parameter. The predicted multiaxial fatigue lives of the considered materials(1045HR Steel,S45C Steel,Inconel718 Steel and 16MnR Steel) using the proposed model are found in good agreement with the experimental results.%基于临界平面原理,应用von-Mises准则提出一种能够同时适用于比例与非比例加载的剪切式多轴疲劳损伤参量.新的损伤参量,通过引入一个应力相关因子来考虑临界面上最大剪应变范围和正应变范围对多轴疲劳损伤贡献的不同,同时该因子还考虑了非比例附加强化对材料多轴疲劳寿命的影响.该参量不含有经验常数,便于工程应用.经1045HR钢,S45C钢,Inconel718钢,16MnR钢等四种材料的多轴疲劳试验验证,预测结果与试验结果吻合较好.

  17. Comparison of halogen light and vibroacoustic stimulation on nonreactive fetal heart rate pattern.

    Science.gov (United States)

    Rahimikian, Fatemeh; Rahiminia, Tahereh; Modarres, Maryam; Mehran, Abbas

    2013-03-01

    One of the first-line assessment tools for fetal surveillance is nonstress test (NST), although it is limited by a high rate of false-nonreactive results. This study was performed to investigate if external stimulation from vibroacoustic and halogen light could help in provoking fetal responsiveness and altering NST results. This is a clinical trial. Sampling was done from April to July 2010. One hundred pregnant women with nonreactive NST for 20 min were allocated in two groups: Vibroacoustic stimulated NST (VNST, n = 50) who received vibration from a standard fetal vibratory stimulator and halogen light stimulated NST (LNST, n = 50) who received a halogen light source for 3 and 10 sec, respectively. Results were compared together and then compared to biophysical profile (BPP) scores as a backup test. We used Mann-Whitney U test, Chi-square test, and Fisher's exact test to compare the variables in the two groups through SPSS version 14. P stimulations, 68% nonreactive subjects in halogen light stimulation group and 62% in vibroacoustic stimulation group changed to reactive patterns. Time to onset of the first acceleration (VNST: 2.17 min; LNST: 2.27 min) and the test duration (VNST: 4.91 min; LNST: 5.26 min) were the same in the two groups. In VNST 89.5% and in LNST 87.5% of nonreactivity followed by score 8 in BPP. There was no significant relation between stimulus NSTs and BPPs. Vibroacoustic and light stimulation offer benefits by decreasing the incidence of nonreactive results and reducing the test time. Both halogen light stimulation and vibroacoustic stimulation are safe and efficient in fetal well-being assessment services.

  18. Shear Yielding and Shear Jamming of Dense Hard Sphere Glasses

    Science.gov (United States)

    Urbani, Pierfrancesco; Zamponi, Francesco

    2017-01-01

    We investigate the response of dense hard sphere glasses to a shear strain in a wide range of pressures ranging from the glass transition to the infinite-pressure jamming point. The phase diagram in the density-shear strain plane is calculated analytically using the mean-field infinite-dimensional solution. We find that just above the glass transition, the glass generically yields at a finite shear strain. The yielding transition in the mean-field picture is a spinodal point in presence of disorder. At higher densities, instead, we find that the glass generically jams at a finite shear strain: the jamming transition prevents yielding. The shear yielding and shear jamming lines merge in a critical point, close to which the system yields at extremely large shear stress. Around this point, highly nontrivial yielding dynamics, characterized by system-spanning disordered fractures, is expected.

  19. Magnetohydrodynamic Shearing Waves

    CERN Document Server

    Johnson, B M

    2006-01-01

    I consider the nonaxisymmetric linear theory of an isothermal magnetohydrodynamic (MHD) shear flow. The analysis is performed in the shearing box, a local model appropriate for a thin disk geometry. Linear perturbations in this model can be decomposed in terms of shearing waves (shwaves), which appear spatially as plane waves in a frame comoving with the shear. The time dependence of these waves cannot in general be expressed in terms of a frequency eigenvalue as in a normal mode decomposition, and numerical integration of a set of first-order amplitude equations is required for a complete characterization of their behavior. Their generic time dependence, however, is oscillatory with slowly-varying frequency and amplitude, and one can construct accurate analytic solutions by applying the Wentzel-Kramers-Brillouin method to the full set of amplitude equations. For the bulk of wavenumber space, therefore, the shwaves are well-approximated as modes with time-dependent frequencies and amplitudes. The incompressiv...

  20. Fracture structure near a longitudinal shear macrorupture

    Science.gov (United States)

    Goldstein, R. V.; Osipenko, N. M.

    2012-09-01

    Fracture evolution the near a main longitudinal shear in the presence of normal stresses is studied. Experiments with model materials (gypsum, cheese) showed that a multiscale echelon structure of cracks feathering the main rupture is formed under the shear domination conditions. A system of small cracks in the initial echelon is replaced by an echelon of larger and sparser cracks. Intensive transverse compression along the normal to the shear plane, which imitates the initial stress concentrator, takes the fracture region away from the shear plane. A model of evolution development of the observed echelon structure along the main rupture front under the shear domination conditions is proposed.

  1. Experimental and theoretical studies on the effects of water content on shear creep behavior of weak structural plane of sandstone%不同含水率软弱结构面剪切蠕变试验及模型研究

    Institute of Scientific and Technical Information of China (English)

    李鹏; 刘建

    2009-01-01

    软弱结构面的蠕变特性是岩体重要力学特性之一,其蠕变特性常控制着岩体的蠕变变形和长期强度.软弱结构面中充填物的含水率是影响其蠕变特性的重要因素之一,通过开展不同含水率砂岩软弱结构面剪切蠕变试验,得到了具不同含水率的砂岩软弱结构面剪切蠕变试验曲线.基于得到的剪切蠕变试验曲线,分析了含水率对软弱结构面剪切蠕变特性及长期抗剪强度的影响规律.最后通过模型辨识,采用改进的粘弹塑性模型来描述考虑含水率变化的砂岩软弱结构面蠕变特性.%Creep behavior of weak structural plane is one of the most important mechanical characteristics of rock mass and always has an important influence on deformation and long-term strength of rock mass. Water content of the fillings is a significant factor influencing the creep properties of the weak structural plane. In this study, by multi-stage loading, a series of shear creep tests on the weak structural plane of sandstone with different water contents are conducted. The curves of the shear creep deformation vs. time under different water content of the fillings are derived. The effects of water content on the shear creep behavior and long-term shear strength of weak structural plane of sandstone are analyzed. Compared with the shear strength by rapid shear test, the long-term strength has sharply decreased. Based on the test results and analysis, modified viscoelastoplastic model is identified to describe the behavior of water content influencing on the weak structural plane of sandstones and parameters of this model are also given through back analysis.

  2. Integrated Design and Control of Reactive and Non-Reactive Distillation Processes

    DEFF Research Database (Denmark)

    Mansouri, Seyed Soheil; Sales-Cruz, Mauricio; Huusom, Jakob Kjøbsted

    , an alternative approach is to tackle process design and controllability issues simultaneously, in the early stages of process design. This simultaneous synthesis approach provides optimal/near optimal operation and more efficient control of conventional (non-reactive binary distillation columns) (Hamid et al......., 2010) as well as complex chemical processes; for example, intensified processes such as reactive distillation (Mansouri et al., 2015). Most importantly, it identifies and eliminates potentially promising design alternatives that may have controllability problems later. To date, a number...... of methodologies have been proposed and applied on various problems to address the interactions between process design and control, and they range from optimization-based approaches to model-based methods (Sharifzadeh, 2013). In this work, integrated design and control of non-reactive distillation, ternary...

  3. Clinical course and personality in reactive, compared with nonreactive, delusional disorder.

    Science.gov (United States)

    Pillmann, Frank; Wustmann, Tobias; Marneros, Andreas

    2012-04-01

    Reactive delusional disorder (DD) (with a precipitating factor) has been postulated to differ clinically from nonreactive DD and to show a better prognosis. Our study tests this hypothesis in a sample of patients with persistent DD (International Classification of Diseases, 10th Revision) or DD (Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition) followed during a period of more than 10 years. As part of a long-term study on DD, 19 patients with DD and a stressful life event preceding the onset of the disorder were compared with 24 DD patients without such a life event. Diagnoses, social and biographical data, life events, and outcome were assessed by a semistructured interview and validated rating scales. Personality features were assessed by the NEO Five-Factor Inventory and by the Inventory of Clinical Personality Accentuations. Patients with reactive DD tended to be somewhat younger but showed otherwise little differences to patients with nonreactive DD. In particular, there were no differences in the course of the disorder. However, patients with reactive DD were significantly more often in a stable relationship and showed higher values on neuroticism and more pronounced dependent and borderline personality accentuations in dimensional personality measures. Reactive DD was not found to have a better prognosis than nonreactive DD. However, the results suggest an increased vulnerability for interpersonal conflicts in these patients.

  4. Stability Criteria of 3D Inviscid Shears

    CERN Document Server

    Li, Y Charles

    2009-01-01

    The classical plane Couette flow, plane Poiseuille flow, and pipe Poiseuille flow share some universal 3D steady coherent structure in the form of "streak-roll-critical layer". As the Reynolds number approaches infinity, the steady coherent structure approaches a 3D limiting shear of the form ($U(y,z), 0, 0$) in velocity variables. All such 3D shears are steady states of the 3D Euler equations. This raises the importance of investigating the stability of such inviscid 3D shears in contrast to the classical Rayleigh theory of inviscid 2D shears. Several general criteria of stability for such inviscid 3D shears are derived. In the Appendix, an argument is given to show that a 2D limiting shear can only be the classical laminar shear.

  5. Stereospecificity of the sensory irritation receptor for nonreactive chemicals illustrated by pinene enantiomers.

    Science.gov (United States)

    Kasanen, J P; Pasanen, A L; Pasanen, P; Liesivuori, J; Kosma, V M; Alarie, Y

    1998-01-01

    To clarify the existence of a receptor protein for sensory irritants in trigeminal nerve endings, D- [i.e. (+)] and L- [i.e. (-)] enantiomers of alpha- and beta-pinene as models of nonreactive chemicals were evaluated for their potency in outbred OF1 and NIH/S mice using ASTM E981-84 bioassay. All pinenes possess sensory irritation properties and also induced sedation and signs of anaesthesia but had no pulmonary irritation effects. According to the ratio of RD50 (i.e. concentration which causes a 50% decrease in respiratory rate,f) and vapour pressure (Po), all pinenes are nonreactive chemicals. For nonreactive chemicals, Po and olive oil-gas partition (Loil) can be used to estimate their potency as sensory irritant. Thus, for enantiomers with identical physicochemical properties, the estimated RD50 values are the same. In addition, although alpha- and beta-pinene do not have identical Po and Loil values, their estimated potencies are quite close. However, the experimental results showed that D-enantiomers of pinenes were the most potent as sensory irritants and a difference in potency also exists between alpha- and beta-pinene. RD50 for D-enantiomers of alpha- and beta-pinene were almost equal, 1053 ppm and 1279 ppm in OF1 strain and 1107 ppm and 1419 ppm in NIH/S strain, respectively. Values differed by a factor of approximately 4 to 5 from L-beta-pinene for which the RD50 was 4663 ppm in OF1 and 5811 ppm in NIH/S mice. RD50 could not be determined for L-alpha-pinene; this pinene was almost inactive. D-alpha-pinene seems to best fit the receptor because its experimental RD50 was one-half of the estimated value while for D-beta-pinene those values were equal. On the contrary, L-beta-pinene was about 3 to 4 times less potent than estimated. L-alpha-pinene was only slightly active although it was estimated to be as potent as D-alpha-pinene. The remarkable difference in potency between L-enantiometers is most likely due to a structural difference between alpha- and

  6. Transient transport of reactive and non-reactive solutes in groundwater

    Science.gov (United States)

    Fares, Y. R.; Giacobbe, D.

    2004-06-01

    A numerical model capable of predicting the transient changes in concentration levels of a solute along a homogeneous aquifer system is presented. The advection-dispersion equation (ADE) is utilised in predicting the concentration levels for cases of continuous and instantaneous release modes. The Crank-Nicholson equation is employed in the presented finite difference model. The numerical calculations are carried out using the implicit Gauss-Seidel method with over- and under-relaxation coefficients depending on the state of convergence. The correction terms resulting from the removal of zero- and first-order truncation errors in the ADE with a reaction term have significantly improved the performance of the numerical scheme. Comparisons between the numerically predicted concentrations with analytical and measured values were carried out for cases of non-reactive (tracer) and reactive (organic) solutes with continuous injection in homogeneous isotropic soils. The overshooting problems experienced in the numerical calculations are minimised by refining the finite grid size. The analysis of results has shown that the model can produce reliable simulations for cases of non-reactive solutes. While for the case of solutes undergoing adsorption, accurate concentrations can be predicted by adjusting the influent pore water velocity through the use of a retardation factor, which is suitable for aquifers with low organic carbon content and undergoing hydrophobic partitioning.

  7. Evolution of twist-shear and dip-shear in Faring active region NOAA 10930

    CERN Document Server

    Gosain, Sanjay

    2010-01-01

    We study the evolution of magnetic shear angle in a flare productive active region NOAA 10930. The magnetic shear angle is defined as the deviation in the orientation of the observed magnetic field vector with respect to the potential field vector. The shear angle is measured in horizontal as well as vertical plane. The former is computed by taking the difference between the azimuth angles of the observed and potential field and is called the twist-shear, while the latter is computed by taking the difference between the inclination angles of the observed and potential field and is called the dip-shear. The evolution of the two shear angles is then tracked over a small region located over the sheared penumbra of the delta sunspot in NOAA 10930. We find that, while the twist-shear shows an increasing trend after the flare the dip-shear shows a significant drop after the flare.

  8. Cell disaggregation behavior in shear flow.

    Science.gov (United States)

    Snabre, P; Bitbol, M; Mills, P

    1987-05-01

    The disaggregation behavior of erythrocytes in dextran saline solution was investigated by a light reflectometry technique in a Couette flow and in a plane Poiseuille flow. Dextran concentration and mass average molecular weight of the polymer fraction strongly influence the shear stress dependence of the erythrocyte suspension reflectivity in shear flow and the critical hydrodynamic conditions (shear rate or shear stress) for near-complete cell dispersion. We investigated the influence of cell volume fraction and membrane deformability (heat treatment of the erythrocytes) on the reflectivity of the flowing suspension. This study indicates that the intercell adhesiveness and the shear stress are the only parameters that influence rouleau break-up in steady uniform shear flow, thus eliminating cell volume fraction and membrane deformability as possible factors. However, the critical cross-sectional average shear stress for near-complete cell dispersion through the flow cross-section is shown to depend on the flow pattern. The rotation of cells in a shear flow or the nonuniform shear field in Poiseuille flow indeed increases the flow resistance of cell aggregates. We give a theoretical description of the shear-induced cell disaggregation process in Couette flow and in plane Poiseuille flow. The quantitation of shear forces for cell dispersion provides a way for estimating the surface adhesive energy of the bridging membranes by fluid mechanical technique.

  9. Ultracold Nonreactive Molecules in an Optical Lattice: Connecting Chemistry to Many-Body Physics.

    Science.gov (United States)

    Doçaj, Andris; Wall, Michael L; Mukherjee, Rick; Hazzard, Kaden R A

    2016-04-01

    We derive effective lattice models for ultracold bosonic or fermionic nonreactive molecules (NRMs) in an optical lattice, analogous to the Hubbard model that describes ultracold atoms in a lattice. In stark contrast to the Hubbard model, which is commonly assumed to accurately describe NRMs, we find that the single on-site interaction parameter U is replaced by a multichannel interaction, whose properties we elucidate. Because this arises from complex short-range collisional physics, it requires no dipolar interactions and thus occurs even in the absence of an electric field or for homonuclear molecules. We find a crossover between coherent few-channel models and fully incoherent single-channel models as the lattice depth is increased. We show that the effective model parameters can be determined in lattice modulation experiments, which, consequently, measure molecular collision dynamics with a vastly sharper energy resolution than experiments in a free-space ultracold gas.

  10. Mechanism and Experimental Observability of Global Switching Between Reactive and Nonreactive Coordinates at High Total Energies

    Science.gov (United States)

    Teramoto, Hiroshi; Toda, Mikito; Takahashi, Masahiko; Kono, Hirohiko; Komatsuzaki, Tamiki

    2015-08-01

    We present a mechanism of global reaction coordinate switching, namely, a phenomenon in which the reaction coordinate dynamically switches to another coordinate as the total energy of the system increases. The mechanism is based on global changes in the underlying phase space geometry caused by a switching of dominant unstable modes from the original reactive mode to another nonreactive mode in systems with more than 2 degrees of freedom. We demonstrate an experimental observability to detect a reaction coordinate switching in an ionization reaction of a hydrogen atom in crossed electric and magnetic fields. For this reaction, the reaction coordinate is a coordinate along which electrons escape and its switching changes the escaping direction from the direction of the electric field to that of the magnetic field and, thus, the switching can be detected experimentally by measuring the angle-resolved momentum distribution of escaping electrons.

  11. Strengthening of Shear Walls

    DEFF Research Database (Denmark)

    Hansen, Christian Skodborg

    -plane loaded walls and disks is however not included in any guidelines, and only a small fraction of scientists have initiated research within this topic. Furthermore, studies of the principal behavior and response of a strengthened disk has not yet been investigated satisfactorily, and this is the principal...... be altered to fit the surrounding boundary conditions. The effective cohesive law will then become a function of the investigated structural geometry. A simplified approach for the latter topic was used to predict the load capacity of concrete beams in shear. Results obtained were acceptable, but the model...

  12. Control over colloidal crystallization by shear and electric fields

    NARCIS (Netherlands)

    Wu, Y.L.

    2007-01-01

    We used shear flow and an electric field to control colloidal crystallization. The structures were examined in situ with confocal microscopy. For experiments under shear, a new parallel plate shear cell was designed. It had a zero-velocity plane that was stationary with respect to the microscope. Th

  13. Proper Orthogonal Decomposition Analysis of Shear-Coaxial Injector Flows With and Without Transverse Acoustic Forcing

    Science.gov (United States)

    2011-10-13

    Rev. Fluid Mech. 22, 473-537 [19] Huerre P. 2000. Open shear flow instabilities. In Perspectives in Fluid Dynamics , ed. G.K. Batchelor , H.K... fluid dynamics aspect from the reactive flow processes, and studying the coupling of non-reactive injector flow instabilities with external pressure...2] Dahm, W. J. A., Frieler, C.E., and Tryggvason, G. 1992 Vortex structure and dynamics in the near field of a coaxial jet. J. Fluid Mech. 241

  14. Micromechanics of shear banding

    Energy Technology Data Exchange (ETDEWEB)

    Gilman, J.J.

    1992-08-01

    Shear-banding is one of many instabilities observed during the plastic flow of solids. It is a consequence of the dislocation mechanism which makes plastic flow fundamentally inhomogeneous, and is exacerbated by local adiabatic heating. Dislocation lines tend to be clustered on sets of neighboring glide planes because they are heterogeneously generated; especially through the Koehler multiple-cross-glide mechanism. Factors that influence their mobilities also play a role. Strain-hardening decreases the mobilities within shear bands thereby tending to spread (delocalize) them. Strain-softening has the inverse effect. This paper reviews the micro-mechanisms of these phenomena. It will be shown that heat production is also a consequence of the heterogeneous nature of the microscopic flow, and that dislocation dipoles play an important role. They are often not directly observable, but their presence may be inferred from changes in thermal conductivity. It is argued that after deformation at low temperatures dipoles are distributed a la Pareto so there are many more small than large ones. Instability at upper yield point, the shapes of shear-band fronts, and mechanism of heat generation are also considered. It is shown that strain-rate acceleration plays a more important role than strain-rate itself in adiabatic instability.

  15. Lateral shear interferometry with holo shear lens

    Science.gov (United States)

    Joenathan, C.; Mohanty, R. K.; Sirohi, R. S.

    1984-12-01

    A simple method for obtaining lateral shear using holo shear lenses (HSL) has been discussed. This simple device which produces lateral shears in the orthogonal directions has been used for lens testing. The holo shear lens is placed at or near the focus of the lens to be tested. It has also been shown that HSL can be used in speckle shear interferometry as it performs both the functions of shearing and imaging.

  16. Characteristics of patients with primary and late latent syphilis patients who were initially non-reactive to the rapid plasma reagin test.

    Science.gov (United States)

    Jun, Li; He-Yi, Zheng

    2013-01-01

    We aimed at determining the characteristics of patients with primary and late latent syphilis who were non-reactive on initial screening by rapid plasma reagin (RPR) but reactive by treponemal tests. We collected the RPR test results of all primary and late latent syphilis patients in our hospital from December 2000 to March 2012. The characteristics of syphilis patients who were non-reactive by RPR testing were compared to those of reactive patients. Multiple logistic regression was used to identify factors associated with non-reactive RPR results. Among primary syphilis patients, 37 (16.5%) were non-reactive on initial RPR and were compared with the 187 reactive cases. Age >35 years was an independent factor associated with a non-reactive result in primary cases (odds ratio [OR], 95% confidence intervals [CI] = 3.55 [1.39-9.07]). Of the late latent patients, 61 (8.8%) were non-reactive by RPR and 636 were reactive. Age >34 years was also an independent factor associated with a non-reactive result in late latent cases (OR [95% CI] = 4.30 [2.28-8.12]). This study suggests that RPR testing alone is insufficient to diagnose primary and late latent infections, especially in middle-aged and elderly individuals. Syphilis detection was lower for patients with primary syphilis than for those with late latent syphilis based on the results of the RPR.

  17. Non-reacting Flow Analysis from Combustor Inlet to Outlet using Computational Fluid Dynamics Code

    Directory of Open Access Journals (Sweden)

    G. Ananda Reddy

    2004-10-01

    Full Text Available This paper describes non-reacting flow analysis of a gas turbine combustion system. The method is based on the solution of Navier-Strokes equations using generalised non-orthogonal coordinate system. The turbulence effects are modelled through the renormalisation group k-E model. The method has been applied to a practical gas turbine combustor. The combustionsystem includes swirler vane passages, fuel nozzles, rotor bleed, customer bleed, air-blast atomiser, swirl cone, and all holes in primary , dilution , dome, flare, and cooling ring. Thetotal geometry has been created using the pre-processors GAMBIT and CATIA, and the meshing has been done using GAMBIT, and the analysis carried out in a FLUENT solver. The interaction between the diffuser and the combustor external flows plays a key role in controlling the pressure loss, air flow distribution around the combustor liner, durability, and stability. The aero gas turbine combustor designs are generally guided by experimental methods and past experience; however, experimental methods are inherently slow, costly, especially at hightemperature engine-operating conditions. These drawbacks and the growing need to understand the complex flow-field phenomenon involved, have led to the development of a numericalmodel for predicting flow in the gas turbine combustor. These models are used to optimise the design of the combustor and its subcomponents, and reduce cost, time, and the number ofexperiments.

  18. Measurements of Non-reacting and Reacting Flow Fields of a Liquid Swirl Flame Burner

    Institute of Scientific and Technical Information of China (English)

    CHONG Cheng Tung; HOCHGREB Simone

    2015-01-01

    The understanding of the liquid fuel spray and flow field characteristics inside a combustor is crucial for designing a fuel efficient and low emission device. Characterisation of the flow field of a model gas turbine liquid swirl burner is performed by using a 2-D particle imaging velocimetry(PIV) system. The flow field pattern of an axial flow burner with a fixed swirl intensity is compared under confined and unconfined conditions, i.e., with and without the combustor wall. The effect of temperature on the main swirling air flow is investigated under open and non-reacting conditions. The result shows that axial and radial velocities increase as a result of decreased flow density and increased flow volume. The flow field of the main swirling flow with liquid fuel spray injection is compared to non-spray swirling flow. Introduction of liquid fuel spray changes the swirl air flow field at the burner outlet, where the radial velocity components increase for both open and confined environment. Under reacting condition, the enclosure generates a corner recirculation zone that intensifies the strength of radial velocity. The reverse flow and corner recirculation zone assists in stabilizing the flame by preheating the reactants. The flow field data can be used as validation target for swirl combustion modelling.

  19. A theoretical framework for modeling dilution enhancement of non-reactive solutes in heterogeneous porous media.

    Science.gov (United States)

    de Barros, F P J; Fiori, A; Boso, F; Bellin, A

    2015-01-01

    Spatial heterogeneity of the hydraulic properties of geological porous formations leads to erratically shaped solute clouds, thus increasing the edge area of the solute body and augmenting the dilution rate. In this study, we provide a theoretical framework to quantify dilution of a non-reactive solute within a steady state flow as affected by the spatial variability of the hydraulic conductivity. Embracing the Lagrangian concentration framework, we obtain explicit semi-analytical expressions for the dilution index as a function of the structural parameters of the random hydraulic conductivity field, under the assumptions of uniform-in-the-average flow, small injection source and weak-to-mild heterogeneity. Results show how the dilution enhancement of the solute cloud is strongly dependent on both the statistical anisotropy ratio and the heterogeneity level of the porous medium. The explicit semi-analytical solution also captures the temporal evolution of the dilution rate; for the early- and late-time limits, the proposed solution recovers previous results from the literature, while at intermediate times it reflects the increasing interplay between large-scale advection and local-scale dispersion. The performance of the theoretical framework is verified with high resolution numerical results and successfully tested against the Cape Cod field data.

  20. Fluid-Assisted Shear Failure Within a Ductile Shear Zone

    Science.gov (United States)

    Kirkpatrick, J. D.; Compton, K.; Holk, G. J.

    2015-12-01

    Exhumed shear zones often contain folded and/or dynamically recrystallized structures such as veins and pseudotachylytes that record contemporaneous brittle and ductile deformation representing mixed bulk rheology. Here, we constrain the conditions that promote the transitions between ductile and brittle deformation by investigating quartz veins with shear offsets in the Saddlebag Lake shear zone in the central Sierra Nevada, California. Mesozoic metasedimentary rocks within the shear zone contain transposed bedding, strong cleavage, dextrally rotated porphyroclasts, and a steep mineral lineation, which together suggest an overall transpressive kinematic regime for the ductile deformation. Foliation sub-parallel veins are one subset of the veins in the shear zone. They have observed horizontal trace lengths of up to around 5 meters, though most are obscured by limited exposure, and displacements range from ~3-30 mm, with 1-5 mm of opening. Foliation sub-parallel veins are folded with the foliation and quartz microstructures and fluid inclusion thermobarometry measurements from vein samples indicate temperatures during vein formation by fracture were between 300-680°C. Quartz δ18O values (+5.9 to +16.5) suggest extended fluid-rock interaction that involved magmatic (δ18O ~ +8 to +10) and meteoric (δ18O down to -1) fluids. Foliation sub-parallel veins are most abundant in relatively massive, quartz-rich rocks where they are boudinaged, indicating they were rigid inclusions after formation. Based on the orientation and spatial distribution of the veins, we infer that they formed under high differential stress with pore pressures sufficiently high for the rocks to be critically stressed for shear failure along mechanically weak foliation planes. These observations suggest high pore pressures and mechanical heterogeneity at a variety of scales are necessary conditions for nucleation of shear fractures within ductile shear zones.

  1. Elastic Constants of Plane Orthotropic Elasticity

    DEFF Research Database (Denmark)

    Krenk, Steen

    1979-01-01

    The four independent material parameters of plane orthotropic elasti city are introduced as the effective stiffness, the effective Poisson ratio, the stiffness ratio and the shear parameter. It is proved that stress boundary value problems with zero resulting force on internal contours lead to st...

  2. Averaged Description of Flow (Steady and Transient) and Nonreactive Solute Transport in Random Porous Media

    Energy Technology Data Exchange (ETDEWEB)

    Schvidler, M.; Karasaki, K.

    2011-06-15

    In previous papers (Shvidler and Karasaki, 1999, 2001, 2005, and 2008) we presented and analyzed an approach for finding the general forms of exactly averaged equations of flow and transport in porous media. We studied systems of basic equations for steady flow with sources in unbounded domains with stochastically homogeneous conductivity fields. A brief analysis of exactly averaged equations of nonsteady flow and nonreactive solute transport was also presented. At the core of this approach is the existence of appropriate random Green's functions. For example, we showed that in the case of a 3-dimensional unbounded domain the existence of appropriate random Green's functions is sufficient for finding the exact nonlocal averaged equations for flow velocity using the operator with a unique kernel-vector. Examination of random fields with global symmetry (isotropy, transversal isotropy and orthotropy) makes it possible to describe significantly different types of averaged equations with nonlocal unique operators. It is evident that the existence of random Green's functions for physical linear processes is equivalent to assuming the existence of some linear random operators for appropriate stochastic equations. If we restricted ourselves to this assumption only, as we have done in this paper, we can study the processes in any dimensional bounded or unbounded fields and in addition, cases in which the random fields of conductivity and porosity are stochastically nonhomogeneous, nonglobally symmetrical, etc.. It is clear that examining more general cases involves significant difficulty and constricts the analysis of structural types for the processes being studied. Nevertheless, we show that we obtain the essential information regarding averaged equations for steady and transient flow, as well as for solute transport.

  3. Macropore system characteristics controls on non-reactive solute transport at different flow rates

    Science.gov (United States)

    Larsbo, Mats; Koestel, John

    2014-05-01

    Preferential flow and transport in macroporous soils are important pathways for the leaching of agrochemicals through soils. Preferential solute transport in soil is to a large extent determined by the macropore system characteristics and the water flow conditions. The importance of different characteristics of the macropore system is likely to vary with the flow conditions. The objective of this study was to determine which properties of the macropore system that control the shape of non-reactive tracer solute breakthrough curves at different steady-state flow rates. We sampled five undisturbed columns (20 cm high, 20 cm diameter) from the soil surface of four soils with clay contents between 21 and 50 %. Solute transport experiments were carried out under unsaturated conditions at 2, 4, 6, 8 and 12 mm h-1 flow rates. For each flow rate a pulse of potassium bromide solution was applied at the soil surface and the electrical conductivity was measured with high temporal resolution in the column effluent. We used the 5 % arrival time and the holdback factor to estimate the degree of preferential transport from the resulting breakthrough curves. Unsaturated hydraulic conductivities were measured at the soil surface of the columns using a tension disc infiltrometer. The macropore system was imaged by industrial X-ray computed tomography at a resolution of 125 μm in all directions. Measures of the macropore system characteristics including measures of pore continuity were calculated from these images using the ImageJ software. Results show that the degree of preferential transport is generally increasing with flow rate when larger pores become active in the transport. The degree of preferential flow was correlated to measures of macropore topology. This study show that conclusions drawn from experiments carried out at one flow rate should generally not be extrapolated to other flow rates.

  4. Polar Mohr diagram method and its application in calculating the shear displacements of general shear zones with volume loss--With the Sangshuyuanzi ductile shear zone as an example

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The main problem,in determining the shear displacement of a general shear zone with volume change using the available formula,is that it is hard to know the initial angle between the planes (or lines) in the plane of shear.A planar deformation analysis of this kind of ductile shear zone is carried out with the polar Mohr diagram.If the volume change is induced by homogeneous contraction in the Z direction of the shear zone,there are sufficient conditions for constructing a polar Mohr diagram regardless of sequence of the simple shear and volume change.Therefore,the angle between a line and the shear direction before and after the deformation can be measured.Making use of these lines the shear strain and the volume change can be calculated and the shear displacement can be determined.

  5. Polar Mohr diagram method and its application in calculating the shear displacements of general shear zones with volume loss——With the Sangshuyuanzi ductile shear zone as an example

    Institute of Scientific and Technical Information of China (English)

    李海; 郭召杰; 刘瑞洵; 刘树文; 张志诚

    2000-01-01

    The main problem, in determining the shear displacement of a general shear zone with volume change using the available formula, is that it is hard to know the initial angle between the planes (or lines) in the plane of shear. A planar deformation analysis of this kind of ductile shear zone is carried out with the polar Mohr diagram. If the volume change is induced by homogeneous contraction in the Z direction of the shear zone, there are sufficient conditions for constructing a polar Mohr diagram regardless of sequence of the simple shear and volume change. Therefore, the angle between a line and the shear direction before and after the deformation can be measured. Making use of these lines the shear strain and the volume change can be calculated and the shear displacement can be determined.

  6. Transversely Compressed- and Restrained Shear Joints

    DEFF Research Database (Denmark)

    Schmidt, Jacob Wittrup; Hansen, Christian Skodborg

    2013-01-01

    . This paper presents theoretical model which can predict the response of transversely compressed and restrained single- and double lap shear joints. The interface material model is based on a cohesive law in the shear-slip plane with a descending branch and a uniform frictional stress added due...... to the friction in the crack, emanating from the transverse pressure or restraint. The theoretical model is compared with experimental results from transversely compressed single- and double shear joints. Also theoretical predictions of a mechanical integrated sleeve-wedge anchorage load capacity are carried out...

  7. Improvement of Energy Conversion/Utilization by Exergy Analysis: Selected Cases for Non-Reactive and Reactive Systems

    Directory of Open Access Journals (Sweden)

    Daniele Fiaschi

    2010-02-01

    Full Text Available Exergy analysis is a powerful and systematic tool for the improvement of energy systems, with many possible applications in both conversion and utilization of energy. Here we present selected applications, with a special attention to renewable energy systems (solar, covering both design and operation/control. After these applications to non-reactive systems, potential ways of reducing the large irreversibilities connected to reactive systems (combustion are considered, with special reference to chemically-recuperated gas turbine cycles and topping high-temperature fuel cells.

  8. Separation of microscale chiral objects by shear flow

    OpenAIRE

    Marcos,, Tavares; Fu, Henry C.; Powers, Thomas R.; Stocker, Roman

    2010-01-01

    We show that plane parabolic flow in a microfluidic channel causes nonmotile helically-shaped bacteria to drift perpendicular to the shear plane. Net drift results from the preferential alignment of helices with streamlines, with a direction that depends on the chirality of the helix and the sign of the shear rate. The drift is in good agreement with a model based on resistive force theory, and separation is efficient (>80%) and fast (

  9. Multiaxial fatigue crack path prediction using critical plane concept

    Directory of Open Access Journals (Sweden)

    Jafar Albinmousa

    2016-01-01

    Full Text Available Prediction of fatigue crack orientation can be an essential step for estimating fatigue crack path. Critical plane concept is widely used due to its physical basis that fatigue failure is associated with certain plane(s. However, recent investigations suggest that critical plane concept might need revision. In this paper, fatigue experiments that involve careful measurement of fatigue crack were reviewed. Predictions of fatigue crack orientation using critical plane concept were examined. Projected length and angle were used to characterize fatigue crack. Considering the entire fatigue life, this average representation suggests that it is more reasonable to assume the plane of maximum normal strain as the critical plane even though fundamentally the plane of maximum shear strain is more likely to be the critical one at early initiation stage.

  10. Microalga propels along vorticity direction in a shear flow

    Science.gov (United States)

    Chengala, Anwar; Hondzo, Miki; Sheng, Jian

    2013-05-01

    Using high-speed digital holographic microscopy and microfluidics, we discover that, when encountering fluid flow shear above a threshold, unicellular green alga Dunaliella primolecta migrates unambiguously in the cross-stream direction that is normal to the plane of shear and coincides with the local fluid flow vorticity. The flow shear drives motile microalgae to collectively migrate in a thin two-dimensional horizontal plane and consequently alters the spatial distribution of microalgal cells within a given suspension. This shear-induced algal migration differs substantially from periodic rotational motion of passive ellipsoids, known as Jeffery orbits, as well as gyrotaxis by bottom-heavy swimming microalgae in a shear flow due to the subtle interplay between torques generated by gravity and viscous shear. Our findings could facilitate mechanistic solutions for modeling planktonic thin layers and sustainable cultivation of microalgae for human nutrition and bioenergy feedstock.

  11. Test and Analysis of a New Ductile Shear Connection Design for RC Shear Walls

    DEFF Research Database (Denmark)

    Sørensen, Jesper Harrild; Hoang, Linh Cao; Olesen, John Forbes

    2016-01-01

    This paper presents a new and construction-friendly shear connection for assembly of precast reinforced concrete shear wall elements. In the proposed design, the precast elements have indented interfaces and are connected by a narrow zone grouted with mortar and reinforced with overlapping U......-bar loops. Contrary to the classical shear connections, the planes of the U-bar loops are here parallel to the plane of the wall elements. This feature enables a construction-friendly installation of the elements without the risk of rebars clashing. The core of mortar inside each U-bar loop is reinforced...... with a transverse double T-headed bar to ensure transfer of tension between the overlapping U-bars. Push-off tests show that a significantly ductile load-displacement response can be obtained by the new solution as compared to the performance of the conventional keyed shear connection design. The influence...

  12. Eco-friendly synthesis for MCM-41 nanoporous materials using the non-reacted reagents in mother liquor

    Science.gov (United States)

    2013-01-01

    Nanoporous materials such as Mobil composite material number 41 (MCM-41) are attractive for applications such as catalysis, adsorption, supports, and carriers. Green synthesis of MCM-41 is particularly appealing because the chemical reagents are useful and valuable. We report on the eco-friendly synthesis of MCM-41 nanoporous materials via multi-cycle approach by re-using the non-reacted reagents in supernatant as mother liquor after separating the solid product. This approach was achieved via minimal requirement of chemical compensation where additional fresh reactants were added into the mother liquor followed by pH adjustment after each cycle of synthesis. The solid product of each successive batch was collected and characterized while the non-reacted reagents in supernatant can be recovered and re-used to produce subsequent cycle of MCM-41. The multi-cycle synthesis is demonstrated up to three times in this research. This approach suggests a low cost and eco-friendly synthesis of nanoporous material since less waste is discarded after the product has been collected, and in addition, product yield can be maintained at the high level. PMID:23497184

  13. STRUCTURAL ANALYSIS OF IN-PLANE LOADED CLT BEAMS

    Directory of Open Access Journals (Sweden)

    Mario Jeleč

    2017-01-01

    Full Text Available Cross laminated timber (CLT is a versatile engineered timber product that is increasingly well-known and of global interest in several applications such as full size plane or linear timber elements. The aim of this study involves investigating the performance of CLT beams loaded in-plane by considering bending and shear stress analysis with a special emphasis on the in-plane shear behavior including the complex internal structure of CLT. Numerical analysis based on 3D-FE models was used and compared with two existing analytical approaches, namely representative volume sub element (method I and composite beam theory (method II. The separate verification of bending and shear stresses including tree different shear failure modes was performed, and a good agreement was obtained. The main difference between the results relates to shear failure mode in the crossing areas between the orthogonally bonded lamellas in which the distribution of shear stresses τzx over the crossing areas per height of the CLT beam is not in accordance with the analytical assumptions. The presented analyses constitute the first attempt to contribute to the on-going review process of Eurocode 5 with respect to CLT beams loaded-in plane. Currently, regulations on designing these types of beams do not exist, and thus experimental and numerical investigations are planned in the future.

  14. Critical plane approach to multiaxial variable amplitude fatigue loading

    Directory of Open Access Journals (Sweden)

    Yingyu Wang

    2015-07-01

    Full Text Available A new critical plane approach based on the modified Manson-Coffin curve method (MMCCM is presented in this paper for predicting fatigue lifetime under variable amplitude (VA multiaxial fatigue loading. The critical plane is assumed to coincide with that material plane experiencing the maximum variance of the resolved shear strain. Fatigue damage is hypothesized to be a function of both the amplitude of the resolved shear strain and the so-called critical plane stress ratio. The latter quantity depends on the mean value and the variance of the stress perpendicular to the critical plane as well as on the variance of the shear stress resolved along the direction experiencing the maximum variance of the resolved shear strain. Load cycles are counted from the resolved shear strain time history by using the classic rain flow counting method. Palmgren-Miner’s linear damage rule is applied to estimate cumulative fatigue damage. The accuracy and reliability of the proposed approach is checked by using several experimental data taken from the literature. The estimated fatigue lives based on the new approach are seen to be in sound agreement with the experimental results.

  15. Fixed Sagittal Plane Imbalance

    OpenAIRE

    Savage, Jason W.; Patel, Alpesh A.

    2014-01-01

    Study Design Literature review. Objective To discuss the evaluation and management of fixed sagittal plane imbalance. Methods A comprehensive literature review was performed on the preoperative evaluation of patients with sagittal plane malalignment, as well as the surgical strategies to address sagittal plane deformity. Results Sagittal plane imbalance is often caused by de novo scoliosis or iatrogenic flat back deformity. Understanding the etiology and magnitude of sagittal malalignment is ...

  16. Finite-amplitude steady waves in plane viscous shear flows

    Science.gov (United States)

    Milinazzo, F. A.; Saffman, P. G.

    1985-01-01

    Computations of two-dimensional solutions of the Navier-Stokes equations are carried out for finite-amplitude waves on steady unidirectional flow. Several cases are considered. The numerical method employs pseudospectral techniques in the streamwise direction and finite differences on a stretched grid in the transverse direction, with matching to asymptotic solutions when unbounded. Earlier results for Poiseuille flow in a channel are re-obtained, except that attention is drawn to the dependence of the minimum Reynolds number on the physical constraint of constant flux or constant pressure gradient. Attempts to calculate waves in Couette flow by continuation in the velocity of a channel wall fail. The asymptotic suction boundary layer is shown to possess finite-amplitude waves at Reynolds numbers orders of magnitude less than the critical Reynolds number for linear instability. Waves in the Blasius boundary layer and unsteady Rayleigh profile are calculated by employing the artifice of adding a body force to cancel the spatial or temporal growth. The results are verified by comparison with perturbation analysis in the vicinity of the linear-instability critical Reynolds numbers.

  17. A characterization of the desarguesian planes of order q2 by SL(2,q

    Directory of Open Access Journals (Sweden)

    D. A. Foulser

    1983-01-01

    Full Text Available The main result is that if the translation complement of a translation plane of order q2 contains a group isomorphic to SL(2,q and if the subgroups of order q are elations (shears, then the plane is Desarguesian. This generalizes earlier work of Walker, who assumed that the kernel of the plane contained GF(q.

  18. Systematic tests for position-dependent additive shear bias

    CERN Document Server

    van Uitert, Edo

    2016-01-01

    We present new tests to identify stationary position-dependent additive shear biases in weak gravitational lensing data sets. These tests are important diagnostics for currently ongoing and planned cosmic shear surveys, as such biases induce coherent shear patterns that can mimic and potentially bias the cosmic shear signal. The central idea of these tests is to determine the average ellipticity of all galaxies with shape measurements in a grid in the pixel plane. The distribution of the absolute values of these averaged ellipticities can be compared to randomized catalogues; a difference points to systematics in the data. In addition, we introduce a method to quantify the spatial correlation of the additive bias, which suppresses the contribution from cosmic shear and therefore eases the identification of a position-dependent additive shear bias in the data. We apply these tests to the publicly available shear catalogues from the Canada-France-Hawaii Telescope Lensing Survey (CFHTLenS) and the Kilo Degree Su...

  19. Strain and shear types of the Louzidian ductile shear zone in southern Chifeng, Inner Mongolia, China

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The Louzidian ductile shear zone at the south of Chifeng strikes NE-SW and dips SE at low-medium- angles. This ductile shear zone is mainly composed of granitic mylonite, which grades structurally upward into a chloritized zone, a microbreccia zone, a brittle fault and a gouge zone. All these zones share similar planar attitudes, but contain different linear attitudes and kinematic indicators. Finite strain measurements were performed on feldspar porphyroclasts using the Fry method. These meas- urements yield Fulin indexes of 1.25―3.30, Lode’s parameters of -0.535―-0.112 and strain parameters of 0.41―0.75 for the protomylonite, respectively. These data are plotted within the apparent constric- tional field in Fulin and Hossack diagrams. In contrast, for the mylonite, corresponding parameters are 0.99―1.43, -0.176―-0.004 and 0.63―0.82, respectively, and located in the apparent constrictional field close to the plane strain. The mean kinematic vorticity numbers of the protomylonite and mylonite by using three methods of polar Mohr circle, porphyroclast hyperbolic and oblique foliation, are in the range of 0.67―0.95, suggesting that the ductile shearing is accommodated by general shearing that is dominated by simple shear. Combination of the finite strain and kinematic vorticity indicates that shear type was lengthening shear and resulted in L-tectonite at the initial stage of deformation and the shear type gradually changed into lengthening-thinning shear and produced L-S-tectonite with the uplifting of the shear zone and accumulating of strain. These kinds of shear types only produce a/ab strain facies, so the lineation in the ductile shear zone could not deflect 90° in the progressively deformation.

  20. Planes of satellite galaxies and the cosmic web

    Science.gov (United States)

    Libeskind, Noam I.; Hoffman, Yehuda; Tully, R. Brent; Courtois, Helene M.; Pomarède, Daniel; Gottlöber, Stefan; Steinmetz, Matthias

    2015-09-01

    Recent observational studies have demonstrated that the majority of satellite galaxies tend to orbit their hosts on highly flattened, vast, possibly corotating planes. Two nearly parallel planes of satellites have been confirmed around the M31 galaxy and around the Centaurus A galaxy, while the Milky Way also sports a plane of satellites. It has been argued that such an alignment of satellites on vast planes is unexpected in the standard Λ cold dark matter (ΛCDM) model of cosmology if not even in contradiction to its generic predictions. Guided by ΛCDM numerical simulations, which suggest that satellites are channelled towards hosts along the axis of the slowest collapse as dictated by the ambient velocity shear tensor, we re-examine the planes of local satellites systems within the framework of the local shear tensor derived from the Cosmicflows-2 data set. The analysis reveals that the Local Group and Centaurus A reside in a filament stretched by the Virgo cluster and compressed by the expansion of the Local Void. Four out of five thin planes of satellite galaxies are indeed closely aligned with the axis of compression induced by the Local Void. Being the less massive system, the moderate misalignment of the Milky Way's satellite plane can likely be ascribed to its greater susceptibility to tidal torques, as suggested by numerical simulations. The alignment of satellite systems in the local Universe with the ambient shear field is thus in general agreement with predictions of the ΛCDM model.

  1. Accelerating Oxygen-Reduction Catalysts through Preventing Poisoning with Non-Reactive Species by Using Hydrophobic Ionic Liquids.

    Science.gov (United States)

    Zhang, Gui-Rong; Munoz, Macarena; Etzold, Bastian J M

    2016-02-05

    Developing cost-effective electrocatalysts for the oxygen reduction reaction (ORR) is a prerequisite for broad market penetration of low-temperature fuel cells. A major barrier stems from the poisoning of surface sites by nonreactive oxygenated species and the sluggish ORR kinetics on the Pt catalysts. Herein we report a facile approach to accelerating ORR kinetics by using a hydrophobic ionic liquid (IL), which protects Pt sites from surface oxidation, making the IL-modified Pt intrinsically more active than its unmodified counterpart. The mass activity of the catalyst is increased by three times to 1.01 A mg(-1) Pt @0.9 V, representing a new record for pure Pt catalysts. The enhanced performance of the IL-modified catalyst can be stabilized after 30 000 cycles. We anticipate these results will form the basis for an unprecedented perspective in the development of high-performing electrocatalysts for fuel-cell applications.

  2. Development of EEM based silicon-water and silica-water wall potentials for non-reactive molecular dynamics simulations

    Science.gov (United States)

    Kim, Junghan; Iype, Eldhose; Frijns, Arjan J. H.; Nedea, Silvia V.; van Steenhoven, Anton A.

    2014-07-01

    Molecular dynamics simulations of heat transfer in gases are computationally expensive when the wall molecules are explicitly modeled. To save computational time, an implicit boundary function is often used. Steele's potential has been used in studies of fluid-solid interface for a long time. In this work, the conceptual idea of Steele's potential was extended in order to simulate water-silicon and water-silica interfaces. A new wall potential model is developed by using the electronegativity-equalization method (EEM), a ReaxFF empirical force field and a non-reactive molecular dynamics package PumMa. Contact angle simulations were performed in order to validate the wall potential model. Contact angle simulations with the resulting tabulated wall potentials gave a silicon-water contact angle of 129°, a quartz-water contact angle of 0°, and a cristobalite-water contact angle of 40°, which are in reasonable agreement with experimental values.

  3. The brittle-viscous-plastic evolution of shear bands in the South Armorican Shear Zone

    Science.gov (United States)

    Bukovská, Zita; Jeřábek, Petr; Morales, Luiz F. G.; Lexa, Ondrej; Milke, Ralf

    2014-05-01

    Shear bands are microscale shear zones that obliquely crosscut an existing anisotropy such as a foliation. The resulting S-C fabrics are characterized by angles lower than 45° and the C plane parallel to shear zone boundaries. The S-C fabrics typically occur in granitoids deformed at greenschist facies conditions in the vicinity of major shear zones. Despite their long recognition, mechanical reasons for localization of deformation into shear bands and their evolution is still poorly understood. In this work we focus on microscale characterization of the shear bands in the South Armorican Shear Zone, where the S-C fabrics were first recognized by Berthé et al. (1979). The initiation of shear bands in the right-lateral South Armorican Shear Zone is associated with the occurrence of microcracks crosscutting the recrystallized quartz aggregates that define the S fabric. In more advanced stages of shear band evolution, newly formed dominant K-feldspar, together with plagioclase, muscovite and chlorite occur in the microcracks, and the shear bands start to widen. K-feldspar replaces quartz by progressively bulging into the grain boundaries of recrystallized quartz grains, leading to disintegration of quartz aggregates and formation of fine-grained multiphase matrix mixture. The late stages of shear band development are marked by interconnection of fine-grained white mica into a band that crosscuts the original shear band matrix. In its extremity, the shear band widening may lead to the formation of ultramylonites. With the increasing proportion of shear band matrix from ~1% to ~12%, the angular relationship between S and C fabrics increases from ~30° to ~40°. The matrix phases within shear bands show differences in chemical composition related to distinct evolutionary stages of shear band formation. The chemical evolution is well documented in K-feldspar, where the albite component is highest in porphyroclasts within S fabric, lower in the newly formed grains within

  4. Moving Overlapping Grids with Adaptive Mesh Refinement for High-Speed Reactive and Non-reactive Flow

    Energy Technology Data Exchange (ETDEWEB)

    Henshaw, W D; Schwendeman, D W

    2005-08-30

    We consider the solution of the reactive and non-reactive Euler equations on two-dimensional domains that evolve in time. The domains are discretized using moving overlapping grids. In a typical grid construction, boundary-fitted grids are used to represent moving boundaries, and these grids overlap with stationary background Cartesian grids. Block-structured adaptive mesh refinement (AMR) is used to resolve fine-scale features in the flow such as shocks and detonations. Refinement grids are added to base-level grids according to an estimate of the error, and these refinement grids move with their corresponding base-level grids. The numerical approximation of the governing equations takes place in the parameter space of each component grid which is defined by a mapping from (fixed) parameter space to (moving) physical space. The mapped equations are solved numerically using a second-order extension of Godunov's method. The stiff source term in the reactive case is handled using a Runge-Kutta error-control scheme. We consider cases when the boundaries move according to a prescribed function of time and when the boundaries of embedded bodies move according to the surface stress exerted by the fluid. In the latter case, the Newton-Euler equations describe the motion of the center of mass of the each body and the rotation about it, and these equations are integrated numerically using a second-order predictor-corrector scheme. Numerical boundary conditions at slip walls are described, and numerical results are presented for both reactive and non-reactive flows in order to demonstrate the use and accuracy of the numerical approach.

  5. Shear System Debugging and Shear Test

    Institute of Scientific and Technical Information of China (English)

    YANG; Dong-xue; JIAO; Hai-yang

    2015-01-01

    Shear system is the essential equipment of head-end processing in the spent fuel reprocessing process,with the aim of cutting spent fuels into appropriate lengths for dissolve,separatingspent fuel core from jacket.Shear system of CRARL is mainly set in 01Bhot cell,element rods will be cut into short lengths of 10-30mm

  6. Platform-based Shear Force Sensor

    Directory of Open Access Journals (Sweden)

    Wang Wei-Chih

    2015-01-01

    Full Text Available In this paper, we will present the development of a flexible fiber optic bend loss sensor for the measurement of plantar pressure and shear stress for diabetic patients. The sensor will allow the measurement of shear stress on the foot, which is a critical parameter in studying diabetic foot ulcers. The basic configuration of the optical sensor systems incorporates a mesh that is comprised of two sets of parallel optical waveguide planes; the planes are configured so the parallel rows of waveguides of the top and bottom planes are perpendicular to each other. The planes are sandwiched together creating one sensing sheet. Two-dimensional information is determined by measuring the loss of light from each of the waveguide to map the overall pressure distribution. The shifting of the layers relative to each other produces different patterns of the sensor output, and shear force information is characterized through repeated training of the sensor and analysis of the training data. The latest development and improvement in the sensors design is presented. Fabrication and sensor characterization results will be presented.

  7. Shear viscosity of nuclear matter

    CERN Document Server

    Magner, A G; Grygoriev, U V; Plujko, V A

    2016-01-01

    Shear viscosity $\\eta$ is calculated for the nuclear matter described as a system of interacting nucleons with the van der Waals (VDW) equation of state. The Boltzmann-Vlasov kinetic equation is solved in terms of the plane waves of the collective overdamped motion. In the frequent collision regime, the shear viscosity depends on the particle number density $n$ through the mean-field parameter $a$ which describes attractive forces in the VDW equation. In the temperature region $T=15\\div 40$~MeV, a ratio of the shear viscosity to the entropy density $s$ is smaller than 1 at the nucleon number density $n =(0.5\\div 1.5)\\,n^{}_0$, where $n^{}_0=0.16\\,$fm$^{-3}$ is the particle density of equilibrium nuclear matter at zero temperature. A minimum of the $\\eta/s$ ratio takes place somewhere in a vicinity of the critical point of the VDW system. Large values of $\\eta/s\\gg 1$ are however found in both the low density, $n\\ll n^{}_0$, and high density, $n>2n^{}_0$, regions. This makes the ideal hydrodynamic approach ina...

  8. Crystallography of shear transformations in zirconium hydrides

    Energy Technology Data Exchange (ETDEWEB)

    Cassidy, Michael Philip [Univ. of Illinois, Urbana-Champaign, IL (United States)

    1978-01-01

    The crystallography and substructure of the transformations which have been hypothesized as involving a martensitic shear, and which occur between zirconium hydrides were investigated. Specifically, the formation of gamma zirconium hydride from delta hydride and the delta hydride to epsilon hydride transformation were studied. The habit planes, orientation relationships, lattice invariant shears, and interface structures were determined by transmission electron microscopy and diffraction. Surface tilts were observed and measured with an interference microscope. The direction and magnitude of the shape strain produced by the formation of gamma were determined by the measurement of fiducial scratch displacements. These results were compared with the phenomenological crystallographic theory of martensitic transformations.

  9. Reduced shear power spectrum

    Energy Technology Data Exchange (ETDEWEB)

    Dodelson, Scott; /Fermilab /Chicago U., Astron. Astrophys. Ctr. /Northwestern U.; Shapiro, Charles; /Chicago U. /KICP, Chicago; White, Martin J.; /UC, Berkeley, Astron.

    2005-08-01

    Measurements of ellipticities of background galaxies are sensitive to the reduced shear, the cosmic shear divided by (1-{kappa}) where {kappa} is the projected density field. They compute the difference between shear and reduced shear both analytically and with simulations. The difference becomes more important an smaller scales, and will impact cosmological parameter estimation from upcoming experiments. A simple recipe is presented to carry out the required correction.

  10. Reduced shear power spectrum

    Energy Technology Data Exchange (ETDEWEB)

    Dodelson, Scott; /Fermilab /Chicago U., Astron. Astrophys. Ctr. /Northwestern U.; Shapiro, Charles; /Chicago U. /KICP, Chicago; White, Martin J.; /UC, Berkeley, Astron.

    2005-08-01

    Measurements of ellipticities of background galaxies are sensitive to the reduced shear, the cosmic shear divided by (1-{kappa}) where {kappa} is the projected density field. They compute the difference between shear and reduced shear both analytically and with simulations. The difference becomes more important an smaller scales, and will impact cosmological parameter estimation from upcoming experiments. A simple recipe is presented to carry out the required correction.

  11. Unitals in Projective Planes

    CERN Document Server

    Barwick, Susan

    2008-01-01

    Unitals are key structures in projective planes, and have connections with other structures in algebra. This book presents a monograph on unitals embedded in finite projective planes. It offers a survey of the research literature on embedded unitals. It is suitable for graduate students and researchers who want to learn about this topic

  12. Fixed sagittal plane imbalance.

    Science.gov (United States)

    Savage, Jason W; Patel, Alpesh A

    2014-12-01

    Study Design Literature review. Objective To discuss the evaluation and management of fixed sagittal plane imbalance. Methods A comprehensive literature review was performed on the preoperative evaluation of patients with sagittal plane malalignment, as well as the surgical strategies to address sagittal plane deformity. Results Sagittal plane imbalance is often caused by de novo scoliosis or iatrogenic flat back deformity. Understanding the etiology and magnitude of sagittal malalignment is crucial in realignment planning. Objective parameters have been developed to guide surgeons in determining how much correction is needed to achieve favorable outcomes. Currently, the goals of surgery are to restore a sagittal vertical axis Sagittal plane malalignment is an increasingly recognized cause of pain and disability. Treatment of sagittal plane imbalance varies according to the etiology, location, and severity of the deformity. Fixed sagittal malalignment often requires complex reconstructive procedures that include osteotomy correction. Reestablishing harmonious spinopelvic alignment is associated with significant improvement in health-related quality-of-life outcome measures and patient satisfaction.

  13. Development of EEM based silicon–water and silica–water wall potentials for non-reactive molecular dynamics simulations

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Junghan; Iype, Eldhose; Frijns, Arjan J.H.; Nedea, Silvia V.; Steenhoven, Anton A. van

    2014-07-01

    Molecular dynamics simulations of heat transfer in gases are computationally expensive when the wall molecules are explicitly modeled. To save computational time, an implicit boundary function is often used. Steele's potential has been used in studies of fluid–solid interface for a long time. In this work, the conceptual idea of Steele's potential was extended in order to simulate water–silicon and water–silica interfaces. A new wall potential model is developed by using the electronegativity-equalization method (EEM), a ReaxFF empirical force field and a non-reactive molecular dynamics package PumMa. Contact angle simulations were performed in order to validate the wall potential model. Contact angle simulations with the resulting tabulated wall potentials gave a silicon–water contact angle of 129°, a quartz–water contact angle of 0°, and a cristobalite–water contact angle of 40°, which are in reasonable agreement with experimental values.

  14. Spatial-temporal evolution of gas migration pathways in coal during shear loading

    Institute of Scientific and Technical Information of China (English)

    Peng; Shoujian; Xu; Jiang; Yin; Guangzhi; Liu; Dong; Wang; Weizhong

    2012-01-01

    Custom designed and built meso shear test equipment was used to examine the shear crack propagation in gassy coal under different gas pressures.The spatial-temporal evolution of gas migration pathways in the coal during shear loading was also researched.The results show that gas pressure can hasten crack growth at the shear fracture surface,can reduce the shear strength of gassy coal,and can accelerate the shear failure process.Shear failure in gassy coal exhibits five stages:the pre-crack stage;the stable crack growth stage;the unsteady crack growth stage;the fracture stage;and,finally,the friction crack stage.The shear breaking creates two kinds of crack,shear cracks and tensile cracks.Cracks first appear in the shear plane at both ends and then extend toward the center until a shear fracture surface forms.The direction of shear crack propagation diverges from the predetermined shear plane by an angle of about 5°-10°.

  15. Confocal microscopy of colloidal dispersions in shear flow using a counter-rotating cone-plate shear cell

    Energy Technology Data Exchange (ETDEWEB)

    Derks, Didi; Wisman, Hans; Blaaderen, Alfons van; Imhof, Arnout [Soft Condensed Matter, Debye Institute, Utrecht University, Princetonplein 5, 3584 CC Utrecht, The (Netherlands)

    2004-09-29

    We report on novel possibilities for studying colloidal suspensions in a steady shear field in real space. Fluorescence confocal microscopy is combined with the use of a counter-rotating cone-plate shear cell. This allows imaging of individual particles in the bulk of a sheared suspension in a stationary plane. Moreover, this plane of zero velocity can be moved in the velocity gradient direction while keeping the shear rate constant. The colloidal system under study consists of rhodamine labelled PMMA spheres in a nearly density and refractive index matched mixture of cyclohexylbromide and cis-decalin. We show measured flow profiles in both the fluid and the crystalline phase and find indications for shear banding in the case of a sheared crystal. Furthermore, we show that, thanks to the counter-rotating principle of the cone-plate shear cell, a layer of particles in the bulk of a sheared crystalline suspension can be imaged for a prolonged time, with the result that their positions can be tracked.

  16. On Howard's Conjecture in Heterogeneous Shear Flow Problem

    Indian Academy of Sciences (India)

    R G Shandil; Jagjit Singh

    2003-11-01

    Howard's conjecture, which states that in the linear instability problem of inviscid heterogeneous parallel shear flow growth rate of an arbitrary unstable wave must approach zero as the wave length decreases to zero, is established in a mathematically rigorous fashion for plane parallel heterogeneous shear flows with negligible buoyancy force $g \\ll 1$ (Miles J W, J. Fluid Mech. 10 (1961) 496–508), where is the basic heterogeneity distribution function).

  17. Shearing stability of lubricants

    Science.gov (United States)

    Shiba, Y.; Gijyutsu, G.

    1984-01-01

    Shearing stabilities of lubricating oils containing a high mol. wt. polymer as a viscosity index improver were studied by use of ultrasound. The oils were degraded by cavitation and the degradation generally followed first order kinetics with the rate of degradation increasing with the intensity of the ultrasonic irradiation and the cumulative energy applied. The shear stability was mainly affected by the mol. wt. of the polymer additive and could be determined in a short time by mechanical shearing with ultrasound.

  18. Shearing stability of lubricants

    Energy Technology Data Exchange (ETDEWEB)

    Shiba, Y.; Gijyutsu, G.

    1984-03-01

    Shearing stabilities of lubricating oils containing a high mol. wt. polymer as a viscosity index improver were studied by use of ultrasound. The oils were degraded by cavitation and the degradation generally followed first order kinetics with the rate of degradation increasing with the intensity of the ultrasonic irradiation and the cumulative energy applied. The shear stability was mainly affected by the mol. wt. of the polymer additive and could be determined in a short time by mechanical shearing with ultrasound.

  19. Is crack branching under shear loading caused by shear fracture? ——A critical review on maximum circumferential stress theory

    Institute of Scientific and Technical Information of China (English)

    孙宗颀

    2001-01-01

    When a crack is subjected to shear force, crack branching usually occurs. Theoretical study shows that the crack branching under shear loading is caused by tensile stress, but not caused by shear fracture. The co-plane shear fracture could be obtained if compressive stress with given direction is applied to the specimen, subsequently, calculated shear fracture toughness, KⅡ C, is larger than KⅠ C. A prerequisite of possible occurrence of mode Ⅱ fracture was proposed. The study of shear fracture shows that the maximum circumferential stress theory considered its criterion as a parametric equation of a curve in KⅠ, KⅡ plane is incorrect; the predicted ratio KⅡ C/KⅠ C=0.866 is incorrect too.

  20. In-plane magnetization-induced quantum anomalous Hall effect.

    Science.gov (United States)

    Liu, Xin; Hsu, Hsiu-Chuan; Liu, Chao-Xing

    2013-08-23

    The quantum Hall effect can only be induced by an out-of-plane magnetic field for two-dimensional electron gases, and similarly, the quantum anomalous Hall effect has also usually been considered for systems with only out-of-plane magnetization. In the present work, we predict that the quantum anomalous Hall effect can be induced by in-plane magnetization that is not accompanied by any out-of-plane magnetic field. Two realistic two-dimensional systems, Bi2Te3 thin film with magnetic doping and HgMnTe quantum wells with shear strains, are presented and the general condition for the in-plane magnetization-induced quantum anomalous Hall effect is discussed based on the symmetry analysis. Nonetheless, an experimental setup is proposed to confirm this effect, the observation of which will pave the way to search for the quantum anomalous Hall effect in a wider range of materials.

  1. Dynamic Stiffness Matrix for a Beam Element with Shear Deformation

    Directory of Open Access Journals (Sweden)

    Walter D. Pilkey

    1995-01-01

    Full Text Available A method for calculating the dynamic transfer and stiffness matrices for a straight Timoshenko shear beam is presented. The method is applicable to beams with arbitrarily shaped cross sections and places no restrictions on the orientation of the element coordinate system axes in the plane of the cross section. These new matrices are needed because, for a Timoshenko beam with an arbitrarily shaped cross section, deflections due to shear in the two perpendicular planes are coupled even when the coordinate axes are chosen to be parallel to the principal axes of inertia.

  2. Vane Shear Strength Based Stability Analysis of Slopes in Unconsolidated Soft Clay

    Institute of Scientific and Technical Information of China (English)

    刘润; 闫澍旺; 张连福

    2004-01-01

    In-situ vane shear test is frequently performed to determine shear strength for slope stability analysis in Tianjin New Harbor.However,the soil shear strength varies with the shear plane orientation.A possible means to reduce the effect of directional dependency of shear strength is to convert the in-situ vane shear strength into undrained shear strength parameters.A method of converting in-situ vane shear strength into undrained shear strength parameters is presented.The shear strength parameters determined for all of the in-situ vane shear strengths are subjected to statistical regression analysis to take into consideration the possible effect of non-homogeneity in the soft clay deposit.Using the regressed shear strength parameters,slope stability analyses are performed for five existing soil slopes.The results of stability analyses indicate that the safety factors obtained from the converted parameters reflect the state of the slopes analyzed much better than those obtained from in-situ vane shear strength and laboratory consolidated-undrained and unconsolidated-undrained strength parameters.It is concluded that the presented methsod of determining undrained shear strength parameters for in-situ vane shear strength is effective.

  3. Shear-Driven Reconnection in Kinetic Models

    Science.gov (United States)

    Black, C.; Antiochos, S. K.; Germaschewski, K.; Karpen, J. T.; DeVore, C. R.; Bessho, N.

    2015-12-01

    The explosive energy release in solar eruptive phenomena is believed to be due to magnetic reconnection. In the standard model for coronal mass ejections (CME) and/or solar flares, the free energy for the event resides in the strongly sheared magnetic field of a filament channel. The pre-eruption force balance consists of an upward force due to the magnetic pressure of the sheared field countered by a downward tension due to overlying unsheared field. Magnetic reconnection disrupts this force balance; therefore, it is critical for understanding CME/flare initiation, to model the onset of reconnection driven by the build-up of magnetic shear. In MHD simulations, the application of a magnetic-field shear is a trivial matter. However, kinetic effects are dominant in the diffusion region and thus, it is important to examine this process with PIC simulations as well. The implementation of such a driver in PIC methods is challenging, however, and indicates the necessity of a true multiscale model for such processes in the solar environment. The field must be sheared self-consistently and indirectly to prevent the generation of waves that destroy the desired system. Plasma instabilities can arise nonetheless. In the work presented here, we show that we can control this instability and generate a predicted out-of-plane magnetic flux. This material is based upon work supported by the National Science Foundation under Award No. AGS-1331356.

  4. Phoresis in a Shearing Gas

    Science.gov (United States)

    Söderholm, Lars H.; Borg, Karl I.

    2003-05-01

    An axially symmetric body small compared with the mean free path is free to move in a shearing gas. The body is treated as a test particle. The force and torque acting on the body are calculated. This force and torque will set the body in motion, which asymptotically will take place in one of the eigendirections of the rate of deformation tensor. The axis of the body then points in the same direction. For a velocity field vx(y) the final motion is parallel to one of the lines x = y and x = -y, and the speed of the motion is given by V = 9μβN/8p (2πkBT/m)1/2 ατb1/4 + 1/2πατ + [8 - (6 - πατ)]b3vx,y. Here μ is the viscosity of the gas, p is the pressure, βN is a number close to unity, T is the temperature, m is the mass of a gas molecule, and ατ is parameter in the boundary conditions close to unity. The non-dimensional numbers b1 and b3 depends on the shape of the body. This speed is of the order of the mean free path of the gas multiplied by the shearing. There will be no motion for a body, which is reflection symmetric in a plane orthogonal to the axis of symmetry. This means that there is a phenomenon of phoresis in a shearing gas, which is analogous to thermophoresis in a gas with a temperature gradient.

  5. A comprehensive model for in-plane and out-of-plane vibration of CANDU fuel endplate rings

    Energy Technology Data Exchange (ETDEWEB)

    Yu, S.D., E-mail: syu@ryerson.ca; Fadaee, M.

    2016-08-01

    Highlights: • Proposed an effective method for modelling bending and torsional vibration of CANDU fuel endplate rings. • Applied successfully the thick plate theory to curved structural members by accounting for the transverse shear effect. • The proposed method is computationally more efficient compared to the 3D finite element. - Abstract: In this paper, a comprehensive vibration model is developed for analysing in-plane and out-of-plane vibration of CANDU fuel endplate rings by taking into consideration the effects of in-plane extension in the circumferential and radial directions, shear, and rotatory inertia. The model is based on Reddy’s thick plate theory and the nine-node isoparametric Lagrangian plate finite elements. Natural frequencies of various modes of vibration of circular rings obtained using the proposed method are compared with 3D finite element results, experimental data and results available in the literature. Excellent agreement was achieved.

  6. Shear band in sand with spatially varying density

    Science.gov (United States)

    Borja, Ronaldo I.; Song, Xiaoyu; Rechenmacher, Amy L.; Abedi, Sara; Wu, Wei

    2013-01-01

    Bifurcation theory is often used to investigate the inception of a shear band in a homogeneously deforming body. The theory predicts conjugate shear bands that have the same likelihood of triggering. For structures loaded symmetrically the choice of which of the two conjugate shear bands will persist is arbitrary. In this paper we show that spatial density variation could be a determining factor for the selection of the persistent shear band in a symmetrically loaded localizing sand body. We combine experimental imaging on rectangular sand specimens loaded in plane strain compression with mesoscale finite element modeling on symmetrically loaded sand specimens to show that spatial heterogeneity in density does have a profound impact on the persistent shear band.

  7. Comment on shear-rotation mechanism for martensitic transformations

    Institute of Scientific and Technical Information of China (English)

    CHEN Zi; GUO Zhenghong

    2004-01-01

    The "shear-rotation mechanism" for f.c.c.→b.c.c.(b.c.t.) martensitic transformation is further discussed in this paper. Although "shear-rotation mechanism" involves some valuable ideas which is based on the Nishiyama's model, the concept of "rotation" in "shear-rotation mechanism" may not be consistent with the general definition in crystallography. In addition, the mathematical expression of this mechanism is questionable. Furthermore, a detailed mathematical analysis given in the present paper indicates that the nature of "shear-rotation mechanism" is equivalent to the first two steps of Nishiyama's model, I.e. It is an invariant line strain (ILS) rather than an invariant plane strain (IPS). In other words, it is difficult to obtain the IPS based on the "shear-rotation mechanism" even though the isotropic contraction is involved. Therefore, a new method should be developed to explain the IPS based on Nishiyama's model.

  8. SNAP focal plane

    Energy Technology Data Exchange (ETDEWEB)

    Lampton, Michael L.; Kim, A.; Akerlof, C.W.; Aldering, G.; Amanullah, R.; Astier, P.; Barrelet, E.; Bebek, C.; Bergstrom, L.; Berkovitz, J.; Bernstein, G.; Bester, M.; Bonissent, A.; Bower, C.; Carithers Jr., W.C.; Commins, E.D.; Day, C.; Deustua, S.E.; DiGennaro,R.; Ealet, A.; Ellis, R.S.; Eriksson, M.; Fruchter, A.; Genat, J.-F.; Goldhaber, G.; Goobar, A.; Groom, D.; Harris, S.E.; Harvey, P.R.; Heetderks, H.D.; Holland, S.E.; Huterer, D.; Karcher, A.; Kolbe, W.; Krieger, B.; Lafever, R.; Lamoureux, J.; Levi, M.E.; Levin, D.S.; Linder,E.V.; Loken, S.C.; Malina, R.; Massey, R.; McKay, T.; McKee, S.P.; Miquel, R.; Mortsell, E.; Mostek, N.; Mufson, S.; Musser, J.; Nugent, P.; Oluseyi, H.; Pain, R.; Palaio, N.; Pankow, D.; Perlmutter, S.; Pratt, R.; Prieto, E.; Refregier, A.; Rhodes, J.; Robinson, K.; Roe, N.; Sholl, M.; Schubnell, M.; Smadja, G.; Smoot, G.; Spadafora, A.; Tarle, G.; Tomasch,A.; von der Lippe, H.; Vincent, R.; Walder, J.-P.; Wang, G.

    2002-07-29

    The proposed SuperNova/Acceleration Probe (SNAP) mission will have a two-meter class telescope delivering diffraction-limited images to an instrumented 0.7 square-degree field sensitive in the visible and near-infrared wavelength regime. We describe the requirements for the instrument suite and the evolution of the focal plane design to the present concept in which all the instrumentation--visible and near-infrared imagers, spectrograph, and star guiders--share one common focal plane.

  9. Evolution of shear banding flows in metallic glasses characterized by molecular dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Yao, Li, E-mail: yltiger@sjtu.edu.cn [Shanghai Institute of Space Power-Sources, 2965 Dongchuan Rd., Shanghai 200245 (China); Luan, Yingwei [School of Materials Science and Engineering, Shanghai Jiao Tong University, 800 Dongchuan Rd., Shanghai 200240 (China)

    2016-06-21

    To reveal the evolution of shear banding flows, one-dimensional nanostructure metallic glass composites have been studied with molecular dynamics. The inherent size determines the initial thickness of shear bands, and the subsequent broadening can be restricted to some extent. The vortex-like flows evoke the atomic motion perpendicular to the shear plane, which accelerates the interatomic diffusion. The reduction of local strain rate causes the flow softening for monolithic Cu-Zr glass, but the participation of Cu-atoms in the shear banding flow gradually leads to the shear hardening for the composites.

  10. Beamlet focal plane diagnostic

    Energy Technology Data Exchange (ETDEWEB)

    Caird, J.A.; Nielsen, N.D.; Patton, H.G.; Seppala, L.G.; Thompson, C.E.; Wegner, P.J.

    1996-12-01

    This paper describes the major optical and mechanical design features of the Beamlet Focal Plane Diagnostic system as well as measurements of the system performance, and typical data obtained to date. We also discuss the NIF requirements on the focal spot that we are interested in measuring, and some of our plans for future work using this system.

  11. Structural Evidence for Fluid-Assisted Shear Failure within a Ductile Shear Zone

    Science.gov (United States)

    Compton, K.; Kirkpatrick, J. D.

    2014-12-01

    Recent observations of seismic slip occurring below the seismogenic zone of large fault zones have emphasized the significance of coeval ductile and brittle processes at high temperatures. We present observations of a shear zone contained within the Saddlebag Lake pendant of the eastern Sierra Nevada, CA, where Triassic and Jurassic metavolcanics and metasediments are highly strained in a high-temperature shear zone. Transposed bedding and cleavage that define a flattening fabric, dextrally rotated porphyroclasts, and a steep, pervasive lineation together suggest an overall transpressive kinematic regime for the ductile deformation. The high-strain rocks exhibit multiple episodes of vein formation, indicating a prolonged migration of hydrothermal fluids throughout the system. Crosscutting relationships and mineral assemblages define discrete sets of differently oriented veins. The veins form by fracture, but many veins are folded and boudinaged, showing synkinematic brittle and ductile deformation. We document foliation-parallel quartz veins that show shear displacement from the geometry of pull-apart structures and offsets of earlier veins. Synkinematic equilibrium mineral assemblages within the host rock and dynamic recrystallization of the quartz veins show they formed at temperatures around 400 to 500°C. The shear fractures have horizontal trace lengths of up to a few meters and displacements range from 2-3 mm to ~3 cm, with 1-5 mm of opening. Assuming the observed offset in the fractures occurred in a single event, these measurements are consistent with stress drops of 1 to 10 MPa. We interpret these observations to show that the veins formed as a result of high pore fluid pressure that caused shear failure at low effective stresses. Because foliated rocks are mechanically anisotropic, the foliation provided planes of weakness for failure with a preferred orientation. Evidence for shear failure occurring within crystal-plastic shear zones at high temperatures

  12. The effect of shearing rate and slope angle on the simple shear response of marine clays

    Science.gov (United States)

    Biscontin, G.; Rutherford, C.

    2010-12-01

    The response of submarine slopes to seismic or storm loading has become an important element in the risk assessment for offshore structures and local tsunami hazard. Evaluation of submarine slope stability requires characterization of soil behavior and relies on the selection of appropriate parameter values. Although the traditional simple shear device has been used to investigate cyclic loading effects on marine clay, it does not allow for complex loading conditions which often contribute to the failure on submarine slopes. Understanding the interaction between the initial shear stress, the slope angle, and the multi-directional shaking due to earthquakes or storm loading is an important aspect to understanding the failure mechanisms of submarine slope failures. The initial static driving force on the slope is combined with the dynamic loading by storms and earthquakes to create complex loading paths. Therefore, the ability to apply complex stress or strain paths is important to fully study the shear response of marine clays on submarine slopes. A new multi-directional simple shear device developed at Texas A&M University allows loading along three independent axes, two perpendicular horizontal directions to allow any stress or strain paths in the horizontal plane, and a third in the vertical direction. This device is used to investigate the response of Gulf of Mexico marine deposits to different loading conditions. To study the effect of slope angle on the shear response of the soil, samples are subjected to a shear stress during consolidation, Kα consolidation. One-dimensional monotonic and cyclic shearing of Ko consolidated specimens is used to simulate level ground conditions, whereas sloping surfaces were simulated using Kα consolidation for both monotonic and cyclic tests. The effects of shearing rate on the soil response are investigated using strain controlled tests at varying frequencies.

  13. Simple models for shear flow transition

    Science.gov (United States)

    Barkley, Dwight

    2011-11-01

    I will discuss recent developments in modeling transitional shear flows with simple two-variable models. Both pipe flow and plane Couette flow are considered. The essential insight is that most large-scale features of these shear flows can be traced to a change from excitability to bistability in the local dynamics. Models are presented in two variables, turbulence intensity and mean shear. A PDE model of pipe flow captures the essence of the puff-slug transition as a change from excitability to bistability. Extended models with turbulence as deterministic transient chaos or multiplicative noise reproduce almost all large-scale features of transitional pipe flow. In particular they capture metastable localized puffs, puff splitting, slugs, localized edge states, a continuous transition to sustained turbulence via spatiotemporal intermittency (directed percolation), and a subsequent increase in turbulence fraction towards uniform, featureless turbulence. A model that additionally takes into account the symmetries of plane Couette flow reproduces localized turbulence and periodic turbulent-laminar bands.

  14. Cross Shear Roll Bonding

    DEFF Research Database (Denmark)

    Bay, Niels; Bjerregaard, Henrik; Petersen, Søren. B;

    1994-01-01

    The present paper describes an investigation of roll bonding an AlZn alloy to mild steel. Application of cross shear roll bonding, where the two equal sized rolls run with different peripheral speed, is shown to give better bond strength than conventional roll bonding. Improvements of up to 20......-23% in bond strength are found and full bond strength is obtained at a reduction of 50% whereas 65% is required in case of conventional roll bonding. Pseudo cross shear roll bonding, where the cross shear effect is obtained by running two equal sized rolls with different speed, gives the same results....

  15. Angular shear plate

    Science.gov (United States)

    Ruda, Mitchell C [Tucson, AZ; Greynolds, Alan W [Tucson, AZ; Stuhlinger, Tilman W [Tucson, AZ

    2009-07-14

    One or more disc-shaped angular shear plates each include a region thereon having a thickness that varies with a nonlinear function. For the case of two such shear plates, they are positioned in a facing relationship and rotated relative to each other. Light passing through the variable thickness regions in the angular plates is refracted. By properly timing the relative rotation of the plates and by the use of an appropriate polynomial function for the thickness of the shear plate, light passing therethrough can be focused at variable positions.

  16. Strain and shear types of the Louzidian ductile shear zone in southern Chifeng,Inner Mongolia,China

    Institute of Scientific and Technical Information of China (English)

    WANG XinShe; ZHENG YaDong; WANG Tao

    2007-01-01

    The Louzidian ductile shear zone at the south of Chifeng strikes NE-SW and dips SE at low-mediumangles. This ductile shear zone is mainly composed of granitic mylonite, which grades structurally upward into a chloritized zone, a microbreccia zone, a brittle fault and a gouge zone. All these zones share similar planar attitudes. But contain different linear attitudes and kinematic indicators. Finite strain measurements were performed on feldspar porphyroclasts using the Fry method. These measurements yield Fulin indexes of 1.25-3.30,Lode's parameters of-0.535-0.112 and strain parameters of 0.41-0.75 for the protomylonite, respectively. These data are plotted within the apparent constrictional field in Fulin and Hossack diagrams. In contrast, for the mylonite, corresponding parameters are 0.99-1.43,-0.176--0.004 and 0.63-0.82,respectively,and located in the apparent constrictional field close to the plane strain. The mean kinematic vorticity numbers of the protomylonite and mylonite by using three methods of polar Mohr circle, porphyroclast hyperbolic and oblique foliation, are in the range of 0.67-0.95,suggesting that the ductile shearing is accommodated by general shearing that is dominated by simple shear. Combination of the finite strain and kinematic vorticity indicates that shear type was lengthening shear and resulted in L-tectonite at the initial stage of deformation and the shear type gradually changed into lengthening-thinning shear and produced L-S-tectonite with the uplifting of the shear zone and accumulating of strain. These kinds of shear types only produce a/ab strain facies, so the lineation in the ductile shear zone could not deflect 90.in the progressively deformation.

  17. Boundaries in digital planes

    Directory of Open Access Journals (Sweden)

    Efim Khalimsky

    1990-01-01

    Full Text Available The importance of topological connectedness properties in processing digital pictures is well known. A natural way to begin a theory for this is to give a definition of connectedness for subsets of a digital plane which allows one to prove a Jordan curve theorem. The generally accepted approach to this has been a non-topological Jordan curve theorem which requires two different definitions, 4-connectedness, and 8-connectedness, one for the curve and the other for its complement.

  18. BKP plane partitions

    Energy Technology Data Exchange (ETDEWEB)

    Foda, Omar; Wheeler, Michael [Department of Mathematics and Statistics, University of Melbourne, Parkville, Victoria 3010 (Australia)

    2007-01-15

    Using BKP neutral fermions, we derive a product expression for the generating function of volume-weighted plane partitions that satisfy two conditions. If we call a set of adjacent equal height-h columns, h > 0, an h-path, then 1. Every h-path can assume one of two possible colours. 2. There is a unique way to move along an h-path from any column to another.

  19. Reverberant shear wave fields and estimation of tissue properties

    Science.gov (United States)

    Parker, Kevin J.; Ormachea, Juvenal; Zvietcovich, Fernando; Castaneda, Benjamin

    2017-02-01

    The determination of shear wave speed is an important subject in the field of elastography, since elevated shear wave speeds can be directly linked to increased stiffness of tissues. MRI and ultrasound scanners are frequently used to detect shear waves and a variety of estimators are applied to calculate the underlying shear wave speed. The estimators can be relatively simple if plane wave behavior is assumed with a known direction of propagation. However, multiple reflections from organ boundaries and internal inhomogeneities and mode conversions can create a complicated field in time and space. Thus, we explore the mathematics of multiple component shear wave fields and derive the basic properties, from which efficient estimators can be obtained. We approach this problem from the historic perspective of reverberant fields, a conceptual framework used in architectural acoustics and related fields. The framework can be recast for the alternative case of shear waves in a bounded elastic media, and the expected value of displacement patterns in shear reverberant fields are derived, along with some practical estimators of shear wave speed. These are applied to finite element models and phantoms to illustrate the characteristics of reverberant fields and provide preliminary confirmation of the overall framework.

  20. Interaction of monopoles, dipoles, and turbulence with a shear flow

    Science.gov (United States)

    Marques Rosas Fernandes, V. H.; Kamp, L. P. J.; van Heijst, G. J. F.; Clercx, H. J. H.

    2016-09-01

    Direct numerical simulations have been conducted to examine the evolution of eddies in the presence of large-scale shear flows. The numerical experiments consist of initial-value-problems in which monopolar and dipolar vortices as well as driven turbulence are superposed on a plane Couette or Poiseuille flow in a periodic two-dimensional channel. The evolution of the flow has been examined for different shear rates of the background flow and different widths of the channel. Results found for retro-grade and pro-grade monopolar vortices are consistent with those found in the literature. Boundary layer vorticity, however, can significantly modify the straining and erosion of monopolar vortices normally seen for unbounded domains. Dipolar vortices are shown to be much more robust coherent structures in a large-scale shear flow than monopolar eddies. An analytical model for their trajectories, which are determined by self-advection and advection and rotation by the shear flow, is presented. Turbulent kinetic energy is effectively suppressed by the shearing action of the background flow provided that the shear is linear (Couette flow) and of sufficient strength. Nonlinear shear as present in the Poiseuille flow seems to even increase the turbulence strength especially for high shear rates.

  1. Domino boudinage under layer-parallel simple shear

    Science.gov (United States)

    Dabrowski, Marcin; Grasemann, Bernhard

    2014-11-01

    The boudin segments of a torn competent layer experience synthetic rotation in layer-parallel simple shear. As long as the individual segments in a boudin train are constrained by their neighbors, even a highly viscous boudin deforms internally to create the necessary space for rotation. The rotation rate is then much smaller compared to the case of an isolated segment. Hence, a small tilt of boudin segments is not indicative of low strain. The rotation rate at this stage largely depends on the aspect ratio of the boudin segments and the scaled gap width. Once the tilted boudins are no longer constrained by their neighbors, the rotation rate greatly accelerates. In the case of a low viscosity ratio between the boudins and the host, the boudin segments develop complex shapes, which may give an impression of shear-band boudins forming under the opposite shear sense. We furthermore investigate the behavior of boudin trains of finite length. The terminal segments are displaced out of the shear plane, deforming into isoclinal folds, and separate into groups of boudin segments that rotate into the shear direction and eventually lead to an overall chaotic appearance of the structure. Natural examples of domino boudinage from a high shear -strain detachment zone in the Western Cyclades (Greece) show many similarities with the modeled structures suggesting that, under simple shear deformation, the rotation and separation of boudin segments is an indicator for high shear strain.

  2. Shear-resistant behavior of light composite shear wall

    Institute of Scientific and Technical Information of China (English)

    李升才; 董毓利

    2015-01-01

    Shear test results for a composite wall panel in a light composite structure system are compared with test results for shear walls in Japan. The analysis results show that this kind of composite wall panel works very well, and can be regarded as a solid panel. The composite wall panel with a hidden frame is essential for bringing its effect on shear resistance into full play. Comprehensive analysis of the shear-resistant behavior of the composite wall panel suggests that the shear of the composite shear wall panel can be controlled by the cracking strength of the web shearing diagonal crack.

  3. Shear-Resistant Behavior Analysis of Light Composite Shear Walls

    Institute of Scientific and Technical Information of China (English)

    李升才; 江见鲸; 于庆荣

    2002-01-01

    Shear test results for a composite wall panel in a light composite structure system are compared with test results for shear walls in Japan in this paper. The analysis results show that this kind of composite wall panel works very well, and can be regarded as a solid panel. The composite wall panel with a hidden frame is essential for bringing its effect on shear resistance into full play. Comprehensive analysis of the shear-resistant behavior of the composite wall panel suggests that the shear of the composite shear wall panel can be controlled by the cracking strength of the web shearing diagonal crack.

  4. Direct Shear Tests with Evaluation of Variable Shearing Area

    Directory of Open Access Journals (Sweden)

    Šarūnas Skuodis

    2014-12-01

    Full Text Available Investigations of soil shear strength properties for Baltic Sea shore sand along Klaipėda city are presented. Investigated sand angle of internal friction (φ and cohesion (c is determined via two different direct shear tests procedures. First procedure is standard and ordinary in geotechnical practice, when direct shear test is provided using constant shearing area A0. Second test procedure is different because shearing area according to horizontal displacement each test second is recalculated. This recalculated shearing area author’s call corrected shearing area A. Obtained normal and tangential stresses’ difference via two different testing procedures was 10%.

  5. Strong electron-scale instability in relativistic shear flows

    Science.gov (United States)

    Alves, Eduardo Paulo; Grismayer, Thomas; Fonseca, Ricardo; Silva, Luis

    2013-10-01

    Collisionless shear-driven plasma instabilities have recently been shown to be capable of generating strong and large-scale magnetic fields and may therefore play an important role in relativistic astrophysical outflows. We present a new collisionless shear-driven plasma instability, which operates in the plane transverse to the Kelvin Helmholtz instability (KHI). We develop the linear stability analysis of electromagnetic modes in the transverse plane and find that the growth rate of this instability is greater than the competing KHI in relativistic shears. The analytical results are confirmed with 2D particle-in-cell (PIC) simulations. Simulations also reveal the nonlinear evolution of the instability which leads to the development of mushroom-like electron-density structures, similar to the Rayleigh Taylor instability. Finally, the interplay between the competing instabilities is investigated in 3D PIC simulations.

  6. Stochastically driven instability in rotating shear flows

    CERN Document Server

    Mukhopadhyay, Banibrata

    2012-01-01

    Origin of hydrodynamic turbulence in rotating shear flows is investigated. The particular emphasis is the flows whose angular velocity decreases but specific angular momentum increases with increasing radial coordinate. Such flows are Rayleigh stable, but must be turbulent in order to explain observed data. Such a mismatch between the linear theory and observations/experiments is more severe when any hydromagnetic/magnetohydrodynamic instability and then the corresponding turbulence therein is ruled out. The present work explores the effect of stochastic noise on such hydrodynamic flows. We essentially concentrate on a small section of such a flow which is nothing but a plane shear flow supplemented by the Coriolis effect. This also mimics a small section of an astrophysical accretion disk. It is found that such stochastically driven flows exhibit large temporal and spatial correlations of perturbation velocities, and hence large energy dissipations of perturbation, which presumably generate instability. A ra...

  7. Constant load and constant volume response of municipal solid waste in simple shear.

    Science.gov (United States)

    Zekkos, Dimitrios; Fei, Xunchang

    2017-05-01

    Constant load and constant volume simple shear testing was conducted on relatively fresh municipal solid waste (MSW) from two landfills in the United States, one in Michigan and a second in Texas, at respective natural moisture content below field capacity. The results were assessed in terms of two failure strain criteria, at 10% and 30% shear strain, and two interpretations of effective friction angle. Overall, friction angle obtained assuming that the failure plane is horizontal and at 10% shear strain resulted in a conservative estimation of shear strength of MSW. Comparisons between constant volume and constant load simple shear testing results indicated significant differences in the shear response of MSW with the shear resistance in constant volume being lower than the shear resistance in constant load. The majority of specimens were nearly uncompacted during specimen preparation to reproduce the state of MSW in bioreactor landfills or in uncontrolled waste dumps. The specimens had identical percentage of waste. The results of these tests suggest the possibility of significantly lower shear strength of MSW in bioreactor landfills where waste is placed with low compaction effort and constant volume, i.e., "undrained", conditions may occur. Compacted MSW specimens resulted in shear strength parameters that are higher than uncompacted specimens and closer to values reported in the literature. However, the normalized undrained shear strength in simple shear for uncompacted and compacted MSW was still higher than the normalized undrained shear strength reported in the literature for clayey and silty soils. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Assessment of the Partially Resolved Numerical Simulation (PRNS) Approach in the National Combustion Code (NCC) for Turbulent Nonreacting and Reacting Flows

    Science.gov (United States)

    Shih, Tsan-Hsing; Liu, Nan-Suey

    2008-01-01

    This paper describes an approach which aims at bridging the gap between the traditional Reynolds-averaged Navier-Stokes (RANS) approach and the traditional large eddy simulation (LES) approach. It has the characteristics of the very large eddy simulation (VLES) and we call this approach the partially-resolved numerical simulation (PRNS). Systematic simulations using the National Combustion Code (NCC) have been carried out for fully developed turbulent pipe flows at different Reynolds numbers to evaluate the PRNS approach. Also presented are the sample results of two demonstration cases: nonreacting flow in a single injector flame tube and reacting flow in a Lean Direct Injection (LDI) hydrogen combustor.

  9. Dynamics of flexible fibers in shear flow

    Energy Technology Data Exchange (ETDEWEB)

    Słowicka, Agnieszka M.; Wajnryb, Eligiusz; Ekiel-Jeżewska, Maria L., E-mail: mekiel@ippt.pan.pl [Institute of Fundamental Technological Research, Polish Academy of Sciences, Pawińskiego 5b, 02-106 Warsaw (Poland)

    2015-09-28

    Dynamics of flexible non-Brownian fibers in shear flow at low-Reynolds-number are analyzed numerically for a wide range of the ratios A of the fiber bending force to the viscous drag force. Initially, the fibers are aligned with the flow, and later they move in the plane perpendicular to the flow vorticity. A surprisingly rich spectrum of different modes is observed when the value of A is systematically changed, with sharp transitions between coiled and straightening out modes, period-doubling bifurcations from periodic to migrating solutions, irregular dynamics, and chaos.

  10. Flow and segregation in sheared granular slurries

    Science.gov (United States)

    Barentin, C.; Azanza, E.; Pouligny, B.

    2004-04-01

    We study the behaviour of a granular slurry, i.e., a very concentrated suspension of heavy (denser than the fluid) and polydisperse particles sheared between two parallel-plane circular disks. For small gaps, the slurry behaves as a 2d system with a characteristic radial size segregation of particles. For large gaps, the slurry responds as a 3d system, with considerable vertical segregation and a concomitant 2-phase (fluid, solid) flow structure. The thickness ζ of the fluid phase is the 2d-3d gap crossover. Surprisingly, ζ is found to be nearly unaffected by very large changes in the particle size distribution.

  11. Plane and geodetic surveying

    CERN Document Server

    Johnson, Aylmer

    2004-01-01

    Plane and Geodetic Surveying blends theory and practice, conventional techniques and GPS, to provide the ideal book for students of surveying.Detailed guidance is given on how and when the principle surveying instruments (theodolites, Total Stations, levels and GPS) should be used. Concepts and formulae needed to convert instrument readings into useful results are explained. Rigorous explanations of the theoretical aspects of surveying are given, while at the same time a wealth of useful advice about conducting a survey in practice is provided. An accompanying least squares adjustment program

  12. Construction-friendly ductile shear joints for precast concrete panels

    DEFF Research Database (Denmark)

    Sørensen, Jesper Harrild; Hoang, Linh Cao; Fischer, Gregor

    2015-01-01

    The scope of this paper is the shear capacity of in-situ cast joints between precast concrete panels. Current practice with vertical lowering of the wall panels experiences difficulties in the assembly phase, since the traditional U-bar connection requires an overlap in a horizontal plane to allow....... The solution is tested in a push-off experimental setup and the influence of important geometric parameters of the keyed shear joint is investigated. The first peak load carrying capacity is assessed using plasticity models, and the failure modes are identified by the use of digital image correlation....... The upper bound models produce satisfactory results capturing the experimental tendencies and predicting the mode of shear failure in the shear keys....

  13. Nucleation of amorphous shear bands at nanotwins in boron suboxide

    Science.gov (United States)

    An, Qi; Reddy, K. Madhav; Qian, Jin; Hemker, Kevin J.; Chen, Ming-Wei; Goddard, William A., III

    2016-03-01

    The roles of grain boundaries and twin boundaries in mechanical properties are well understood for metals and alloys. However, for covalent solids, their roles in deformation response to applied stress are not established. Here we characterize the nanotwins in boron suboxide (B6O) with twin boundaries along the planes using both scanning transmission electron microscopy and quantum mechanics. Then, we use quantum mechanics to determine the deformation mechanism for perfect and twinned B6O crystals for both pure shear and biaxial shear deformations. Quantum mechanics suggests that amorphous bands nucleate preferentially at the twin boundaries in B6O because the twinned structure has a lower maximum shear strength by 7.5% compared with perfect structure. These results, which are supported by experimental observations of the coordinated existence of nanotwins and amorphous shear bands in B6O, provide a plausible atomistic explanation for the influence of nanotwins on the deformation behaviour of superhard ceramics.

  14. Large-scale ordering of nanoparticles using viscoelastic shear processing

    Science.gov (United States)

    Zhao, Qibin; Finlayson, Chris E.; Snoswell, David R. E.; Haines, Andrew; Schäfer, Christian; Spahn, Peter; Hellmann, Goetz P.; Petukhov, Andrei V.; Herrmann, Lars; Burdet, Pierre; Midgley, Paul A.; Butler, Simon; Mackley, Malcolm; Guo, Qixin; Baumberg, Jeremy J.

    2016-06-01

    Despite the availability of elaborate varieties of nanoparticles, their assembly into regular superstructures and photonic materials remains challenging. Here we show how flexible films of stacked polymer nanoparticles can be directly assembled in a roll-to-roll process using a bending-induced oscillatory shear technique. For sub-micron spherical nanoparticles, this gives elastomeric photonic crystals termed polymer opals showing extremely strong tunable structural colour. With oscillatory strain amplitudes of 300%, crystallization initiates at the wall and develops quickly across the bulk within only five oscillations. The resulting structure of random hexagonal close-packed layers is improved by shearing bidirectionally, alternating between two in-plane directions. Our theoretical framework indicates how the reduction in shear viscosity with increasing order of each layer accounts for these results, even when diffusion is totally absent. This general principle of shear ordering in viscoelastic media opens the way to manufacturable photonic materials, and forms a generic tool for ordering nanoparticles.

  15. Fourier plane image amplifier

    Science.gov (United States)

    Hackel, L.A.; Hermann, M.R.; Dane, C.B.; Tiszauer, D.H.

    1995-12-12

    A solid state laser is frequency tripled to 0.3 {micro}m. A small portion of the laser is split off and generates a Stokes seed in a low power oscillator. The low power output passes through a mask with the appropriate hole pattern. Meanwhile, the bulk of the laser output is focused into a larger stimulated Brillouin scattering (SBS) amplifier. The low power beam is directed through the same cell in the opposite direction. The majority of the amplification takes place at the focus which is the fourier transform plane of the mask image. The small holes occupy large area at the focus and thus are preferentially amplified. The amplified output is now imaged onto the multichip module where the holes are drilled. Because of the fourier plane amplifier, only about 1/10th the power of a competitive system is needed. This concept allows less expensive masks to be used in the process and requires much less laser power. 1 fig.

  16. The Aerodynamic Plane Table

    Science.gov (United States)

    Zahm, A F

    1924-01-01

    This report gives the description and the use of a specially designed aerodynamic plane table. For the accurate and expeditious geometrical measurement of models in an aerodynamic laboratory, and for miscellaneous truing operations, there is frequent need for a specially equipped plan table. For example, one may have to measure truly to 0.001 inch the offsets of an airfoil at many parts of its surface. Or the offsets of a strut, airship hull, or other carefully formed figure may require exact calipering. Again, a complete airplane model may have to be adjusted for correct incidence at all parts of its surfaces or verified in those parts for conformance to specifications. Such work, if but occasional, may be done on a planing or milling machine; but if frequent, justifies the provision of a special table. For this reason it was found desirable in 1918 to make the table described in this report and to equip it with such gauges and measures as the work should require.

  17. The MOND Fundamental Plane

    CERN Document Server

    Cardone, V F; Diaferio, A; Tortora, C; Molinaro, R

    2010-01-01

    Modified Newtonian Dynamics (MOND) has been shown to be able to fit spiral galaxy rotation curves as well as giving a theoretical foundation for empirically determined scaling relations, such as the Tully - Fisher law, without the need for a dark matter halo. As a complementary analysis, one should investigate whether MOND can also reproduce the dynamics of early - type galaxies (ETGs) without dark matter. As a first step, we here show that MOND can indeed fit the observed central velocity dispersion $\\sigma_0$ of a large sample of ETGs assuming a simple MOND interpolating functions and constant anisotropy. We also show that, under some assumptions on the luminosity dependence of the Sersic n parameter and the stellar M/L ratio, MOND predicts a fundamental plane for ETGs : a log - linear relation among the effective radius $R_{eff}$, $\\sigma_0$ and the mean effective intensity $\\langle I_e \\rangle$. However, we predict a tilt between the observed and the MOND fundamental planes.

  18. Fourier plane image amplifier

    Science.gov (United States)

    Hackel, Lloyd A.; Hermann, Mark R.; Dane, C. Brent; Tiszauer, Detlev H.

    1995-01-01

    A solid state laser is frequency tripled to 0.3 .mu.m. A small portion of the laser is split off and generates a Stokes seed in a low power oscillator. The low power output passes through a mask with the appropriate hole pattern. Meanwhile, the bulk of the laser output is focused into a larger stimulated Brillouin scattering (SBS) amplifier. The low power beam is directed through the same cell in the opposite direction. The majority of the amplification takes place at the focus which is the fourier transform plane of the mask image. The small holes occupy large area at the focus and thus are preferentially amplified. The amplified output is now imaged onto the multichip module where the holes are drilled. Because of the fourier plane amplifier, only .about.1/10th the power of a competitive system is needed. This concept allows less expensive masks to be used in the process and requires much less laser power.

  19. Investigation of the stress state on the fault planes and the magnitude of the seismic events occurred from geothermal reservoirs

    Science.gov (United States)

    Mukuhira, Y.; Asanuma, H.; Häring, M. O.; Saeki, K.

    2013-12-01

    Occurrence of felt earthquakes is a critical environmental burden in geothermal development, and studies on control factors of the magnitude of the seismic events have been activated worldwide. We have identified fault planes of the large events occurred from engineered geothermal systems (EGS) sites, at Cooper Basin, Australia, and Basel, Switzerland, and Yanaizu-Nishiyama, a Japanese hydrothermal field. Shear/normal stress working on these fault planes was evaluated on the Mohr stress circles, comparing with the event magnitudes. It has been found that the large events at Basel and Yanaizu-Nishiyama occurred from fault planes where relatively large shear stress is working, although smaller events also occurred from fault planes with large shear stress. Identification of the fault planes of the larger events at Basel showed that large events mainly occurred from two types of sub-vertical fault planes with azimuth of WNW-ESE or N-S (see figure). FPSs of four felt earthquakes in Yanaizu-Nishiyama showed nearly common strike/dip. From these observations, it can be interpreted that the large events from Basel and Yanaizu-Nishiyama were likely to occur from particular fault planes with large shear stress within complex facture system. Similar relationship between shear stress and the magnitude has been also found by several seismologists (e.g. Terakawa et al., 2012). The selectivity in occurrence of the large events among fault planes under common shear stress suggests that there would be some additional factors to control scale of the failure. At Cooper Basin, where limited number of sub-horizontal fractures and vertical fractures connecting them compose the reservoir, the large events occurred from the sub-horizontal fault planes on which many smaller events also occurred. In this case, the moderate shear stress was working on the sub-horizontal fault planes, suggesting that the event magnitudes were mainly controlled by some unknown factors rather than the shear

  20. Shear Horizontal Wave Propagation Speed in Mylar Sheet and Coated Paper

    Science.gov (United States)

    Leppänen, M.; Karppinen, T.; Hæggström, E.; Stor-Pellinen, J.

    2006-03-01

    Soft plate-like membranes find application e.g. as pill or paper coatings, bio-filter membranes, and gas seals in food products. For these applications the integrity and the mechanical properties of the membrane are important. Mechanical properties of these products can be determined by stretching or bending tests, but such methods can damage these fragile products. We propose a rapid nondestructive acoustic method to estimate mechanical film characteristics with shear horizontal (in-plane shear) waves. A 23 kHz, 1-cycle square signal was excited into a thin foil with a piezoceramic pickup and received with an inductive pickup. The SNR (power) was 20 dB in 1 kHz -50 kHz bandwidth. This actuation-detection scheme can be used to excite in-plane longitudinal, shear and even elliptic waves in a thin foil. The method was validated by measuring in-plane shear wave and longitudinal wave time-of-flight TOF at different actuator-receiver separations and calculating the corresponding longitudinal and shear modulus. The samples were Mylar® sheet and coated paper. The anisotropy of MOE for Mylar sheet was close to the manufacturer specifications. For coated paper a maximum shear modulus anisotropy of 5% and a shear modulus dependence on temperature of 0.7 MPa/°C were found. Laser doppler vibrometry showed that the excited waves were confined in-plane.

  1. Free volume under shear

    Science.gov (United States)

    Maiti, Moumita; Vinutha, H. A.; Sastry, Srikanth; Heussinger, Claus

    2015-10-01

    Using an athermal quasistatic simulation protocol, we study the distribution of free volumes in sheared hard-particle packings close to, but below, the random-close packing threshold. We show that under shear, and independent of volume fraction, the free volumes develop features similar to close-packed systems — particles self-organize in a manner as to mimick the isotropically jammed state. We compare athermally sheared packings with thermalized packings and show that thermalization leads to an erasure of these structural features. The temporal evolution in particular the opening-up and the closing of free-volume patches is associated with the single-particle dynamics, showing a crossover from ballistic to diffusive behavior.

  2. Physics of Transitional Shear Flows Instability and Laminar–Turbulent Transition in Incompressible Near-Wall Shear Layers

    CERN Document Server

    Boiko, Andrey V; Grek, Genrih R; Kozlov, Victor V

    2012-01-01

    Starting from fundamentals of classical stability theory, an overview is given of the transition phenomena in subsonic, wall-bounded shear flows. At first, the consideration focuses on elementary small-amplitude velocity perturbations of laminar shear layers, i.e. instability waves, in the simplest canonical configurations of a plane channel flow and a flat-plate boundary layer. Then the linear stability problem is expanded to include the effects of pressure gradients, flow curvature, boundary-layer separation, wall compliance, etc. related to applications. Beyond the amplification of instability waves is the non-modal growth of local stationary and non-stationary shear flow perturbations which are discussed as well. The volume continues with the key aspect of the transition process, that is, receptivity of convectively unstable shear layers to external perturbations, summarizing main paths of the excitation of laminar flow disturbances. The remainder of the book addresses the instability phenomena found at l...

  3. Systematic tests for position-dependent additive shear bias

    Science.gov (United States)

    van Uitert, Edo; Schneider, Peter

    2016-11-01

    We present new tests to identify stationary position-dependent additive shear biases in weak gravitational lensing data sets. These tests are important diagnostics for currently ongoing and planned cosmic shear surveys, as such biases induce coherent shear patterns that can mimic and potentially bias the cosmic shear signal. The central idea of these tests is to determine the average ellipticity of all galaxies with shape measurements in a grid in the pixel plane. The distribution of the absolute values of these averaged ellipticities can be compared to randomised catalogues; a difference points to systematics in the data. In addition, we introduce a method to quantify the spatial correlation of the additive bias, which suppresses the contribution from cosmic shear and therefore eases the identification of a position-dependent additive shear bias in the data. We apply these tests to the publicly available shear catalogues from the Canada-France-Hawaii Telescope Lensing Survey (CFHTLenS) and the Kilo Degree Survey (KiDS) and find evidence for a small but non-negligible residual additive bias at small scales. As this residual bias is smaller than the error on the shear correlation signal at those scales, it is highly unlikely that it causes a significant bias in the published cosmic shear results of CFHTLenS. In CFHTLenS, the amplitude of this systematic signal is consistent with zero in fields where the number of stars used to model the point spread function (PSF) is higher than average, suggesting that the position-dependent additive shear bias originates from undersampled PSF variations across the image.

  4. Mixing through shear instabilities

    CERN Document Server

    Brüggen, M

    2000-01-01

    In this paper we present the results of numerical simulations of the Kelvin-Helmholtz instability in a stratified shear layer. This shear instability is believed to be responsible for extra mixing in differentially rotating stellar interiors and is the prime candidate to explain the abundance anomalies observed in many rotating stars. All mixing prescriptions currently in use are based on phenomenological and heuristic estimates whose validity is often unclear. Using three-dimensional numerical simulations, we study the mixing efficiency as a function of the Richardson number and compare our results with some semi-analytical formalisms of mixing.

  5. Spatiotemporal evolution of a fault shear stress patch due to viscoelastic interseismic fault zone rheology

    Science.gov (United States)

    Sone, Hiroki; Uchide, Takahiko

    2016-08-01

    We conducted numerical studies to explore how shear stress anomalies on fault planes (shear stress patches) evolve spatiotemporally during the interseismic period under the influence of viscoelastic rheology assigned to fault zones of finite thickness. 2-D viscoelastic models consisting of a fault zone and host rock were sheared to simulate shear stress accumulation along fault zones due to tectonic loading. No fault slip along a distinct fault planes is implied in the model, thus all fault shear motion is accommodated by distributed deformation in the viscoelastic fault zone. Results show that magnitudes of shear stress patches evolve not only temporally, but also spatially, especially when the stress anomaly is created by a geometrical irregularity (asperity) along the interface of an elastic host rock and viscoelastic fault zone. Such shear stress anomalies diffuse spatially so that the spatial dimension of the shear stress patch appears to grow over time. Models with varying fault zone viscoelastic properties and varying fault zone viscosity both show that such spatial diffusion of shear stress is enhanced by increasing the contribution of the viscous behavior. The absolute rate at which shear stress patches grow spatially is generally not influenced by the size of the shear stress patch. Therefore shear stress patches with smaller dimensions will appear to grow quicker, in the relative sense, compared to larger stress patches. These results suggest that the minimum dimensions of shear stress patches that can exist along a fault could be governed by the effective viscosity of the fault zone. Therefore patterns of accumulated shear stress could vary along faults when viscous properties are heterogeneous, for instance due to depth or material heterogeneity, which has implications on how earthquake rupture behavior could vary along faults.

  6. Vorticity Fluctuations in Plane Couette Flow

    Science.gov (United States)

    Ortiz de Zarate, Jose; Sengers, Jan V.

    2010-11-01

    In this presentation we evaluate the flow-induced amplification of the thermal noise in plane Couette configuration. The physical origin of the noise is the random nature of molecular collisions, that contribute with a stochastic component to the stress tensor (Landau's fluctuating hydrodynamics). This intrinsic stochastic forcing is then amplified by the mode- coupling mechanisms associated to shear flow. In a linear approximation, noise amplification can be studied by solving stochastic Orr-Sommerfeld and Squire equations. We compare the efficiency of the different mechanisms, being the most important the direct coupling between Squire and Orr-Sommerfed equations. The main effect is to amplify wall-normal vorticity fluctuations with an spanwise modulation at wave number around 1.5, a configuration that resembles the streaks that have been proposed as precursors of the flow instability.

  7. Crisis bifurcations in plane Poiseuille flow.

    Science.gov (United States)

    Zammert, Stefan; Eckhardt, Bruno

    2015-04-01

    Many shear flows follow a route to turbulence that has striking similarities to bifurcation scenarios in low-dimensional dynamical systems. Among the bifurcations that appear, crisis bifurcations are important because they cause global transitions between open and closed attractors, or indicate drastic increases in the range of the state space that is covered by the dynamics. We here study exterior and interior crisis bifurcations in direct numerical simulations of transitional plane Poiseuille flow in a mirror-symmetric subspace. We trace the state space dynamics from the appearance of the first three-dimensional exact coherent structures to the transition from an attractor to a chaotic saddle in an exterior crisis. For intermediate Reynolds numbers, the attractor undergoes several interior crises, in which new states appear and intermittent behavior can be observed. The bifurcations contribute to increasing the complexity of the dynamics and to a more dense coverage of state space.

  8. Synthesis and characterization of photochromic Ag-embedded TiO{sub 2} nanocomposite thin films by non-reactive RF-magnetron sputter deposition

    Energy Technology Data Exchange (ETDEWEB)

    Zuo, J., E-mail: zuojuan@xmut.edu.cn [Department of Materials Science and Engineering, Xiamen University of Technology, Xiamen (China); Department of Interface Chemistry and Surface Engineering, Max-Planck-Institut fuer Eisenforschung GmbH, Duesseldorf (Germany); Keil, P. [Department of Interface Chemistry and Surface Engineering, Max-Planck-Institut fuer Eisenforschung GmbH, Duesseldorf (Germany); Grundmeier, G. [Department of Interface Chemistry and Surface Engineering, Max-Planck-Institut fuer Eisenforschung GmbH, Duesseldorf (Germany); Department of Chemical Engineering and Macromolecular Chemistry, University of Paderborn, Paderborn (Germany)

    2012-07-01

    Ag-embedded TiO{sub 2} nanocomposite thin film with reversible photochromic properties were prepared by layer-by-layer non-reactive RF-magnetron sputtering. Films were produced in Ar/O{sub 2} and pure Ar atmospheres. In the oxidizing regime, a diffusion of Ag from the film volume to the outer film surface was observed. Therefore, pure Ar plasma was applied in the deposition of TiO{sub 2}. The electronic and optical properties of the TiO{sub 2} film were almost not affected by the presence of oxygen. Transmission electron microscopy (TEM) and reflection mode X-ray absorption spectroscopy (XAS) were performed to study the morphology, crystal structure and chemical state of the embedded Ag nanoparticles before and after the annealing step. Annealing of the film led to the crystallization of the TiO{sub 2} matrix. Moreover, the Ag nanoparticles in the film underwent Ostwald ripening leading to particle agglomerate. No oxidation of the embedded Ag during the sputter deposition and subsequent annealing process was found as confirmed by XAS measurements. The non-reactive RF-magnetron method is believed to avoid the energetic oxygen ions attack to Ag during the deposition of Ag-embedded TiO{sub 2} nanocomposite and thus the films are expected to have better optical properties and long-term stability.

  9. Locally Corroded Stiffener Effect on Shear Buckling Behaviors of Web Panel in the Plate Girder

    Directory of Open Access Journals (Sweden)

    Jungwon Huh

    2015-01-01

    Full Text Available The shear buckling failure and strength of a web panel stiffened by stiffeners with corrosion damage were examined according to the degree of corrosion of the stiffeners, using the finite element analysis method. For this purpose, a plate girder with a four-panel web girder stiffened by vertical and longitudinal stiffeners was selected, and its deformable behaviors and the principal stress distribution of the web panel at the shear buckling strength of the web were compared after their post-shear buckling behaviors, as well as their out-of-plane displacement, to evaluate the effect of the stiffener in the web panel on the shear buckling failure. Their critical shear buckling load and shear buckling strength were also examined. The FE analyses showed that their typical shear buckling failures were affected by the structural relationship between the web panel and each stiffener in the plate girder, to resist shear buckling of the web panel. Their critical shear buckling loads decreased from 82% to 59%, and their shear buckling strength decreased from 88% to 76%, due to the effect of corrosion of the stiffeners on their shear buckling behavior. Thus, especially in cases with over 40% corrosion damage of the vertical stiffener, they can have lower shear buckling strength than their design level.

  10. Plane symmetric cosmological models

    CERN Document Server

    Yadav, Anil Kumar; Ray, Saibal; Mallick, A

    2016-01-01

    In this work, we perform the Lie symmetry analysis on the Einstein-Maxwell field equations in plane symmetric spacetime. Here Lie point symmetries and optimal system of one dimensional subalgebras are determined. The similarity reductions and exact solutions are obtained in connection to the evolution of universe. The present study deals with the electromagnetic energy of inhomogeneous universe where $F_{12}$ is the non-vanishing component of electromagnetic field tensor. To get a deterministic solution, it is assumed that the free gravitational field is Petrov type-II non-degenerate. The electromagnetic field tensor $F_{12}$ is found to be positive and increasing function of time. As a special case, to validate the solution set, we discuss some physical and geometric properties of a specific sub-model.

  11. Duality and noncommutative planes

    DEFF Research Database (Denmark)

    Jøndrup, Søren

    2015-01-01

    We study extensions of simple modules over an associative ring A   and we prove that for twosided ideals mm and nn with artinian factors the condition ExtA1(A/m,A/n)≠0 holds for the left A  -modules A/mA/m and A/nA/n if and only if it holds for the right modules A/nA/n and A/mA/m. The methods pro...... proving this are applied to show that noncommutative models of the plane, i.e. algebras of the form k〈x,y〉/(f)k〈x,y〉/(f), where f∈([x,y])f∈([x,y]) are noetherian only in case (f)=([x,y])...

  12. Recrystallization fabrics of sheared quartz veins with a strong pre-existing crystallographic preferred orientation from a seismogenic shear zone

    Science.gov (United States)

    Price, Nancy A.; Song, Won Joon; Johnson, Scott E.; Gerbi, Christopher C.; Beane, Rachel J.; West, David P.

    2016-07-01

    Microstructural investigations were carried out on quartz veins in schist, protomylonite, and mylonite samples from an ancient seismogenic strike-slip shear zone (Sandhill Corner shear zone, Norumbega fault system, Maine, USA). We interpret complexities in the microstructural record to show that: (1) pre-existing crystallographic preferred orientations (CPO) in the host rock may persist in the new CPO patterns of the shear zone and (2) the inner and outer parts of the shear zone followed diverging paths of fabric development. The host rocks bounding the shear zone contain asymmetrically-folded quartz veins with a strong CPO. These veins are increasingly deformed and recrystallized with proximity to the shear zone core. Matrix-accommodated rotation and recrystallization may position an inherited c-axis maximum in an orientation coincident with rhomb or basal slip. This inherited CPO likely persists in the shear zone fabric as a higher concentration of poles in one hemisphere of the c-axis pole figure, leading to asymmetric crossed girdle or paired maxima c-axis patterns about the foliation plane. Three observed quartz grain types indicate a general trend of localization with decreasing temperature: (1) large (> 100 μm), low aspect ratio (<~5) and (2) high aspect ratio (~ 5-20) grains overprinted by (3) smaller (<~80 μm), low aspect ratio (<~4) grains through subgrain rotation-dominated recrystallization. In the outer shear zone, subgrain rotation recrystallization led to a well-developed c-axis crossed girdle pattern. In the inner shear zone, the larger grains are completely overprinted by smaller grains, but the CPO patterns are relatively poorly developed and are associated with distinctively different misorientation angle histogram profiles ("flat" neighbor-pair profile with similar number fraction for angles from 10 to 90°). This may reflect the preferential activation of grain size sensitive deformation processes in the inner-most part of the shear zone

  13. Experimental Validation of the Transverse Shear Behavior of a Nomex Core for Sandwich Panels

    Science.gov (United States)

    Farooqi, M. I.; Nasir, M. A.; Ali, H. M.; Ali, Y.

    2017-05-01

    This work deals with determination of the transverse shear moduli of a Nomex® honeycomb core of sandwich panels. Their out-of-plane shear characteristics depend on the transverse shear moduli of the honeycomb core. These moduli were determined experimentally, numerically, and analytically. Numerical simulations were performed by using a unit cell model and three analytical approaches. Analytical calculations showed that two of the approaches provided reasonable predictions for the transverse shear modulus as compared with experimental results. However, the approach based upon the classical lamination theory showed large deviations from experimental data. Numerical simulations also showed a trend similar to that resulting from the analytical models.

  14. Keyed shear joints

    DEFF Research Database (Denmark)

    Hansen, Klaus

    This report gives a summary of the present information on the behaviour of vertical keyed shear joints in large panel structures. An attemp is made to outline the implications which this information might have on the analysis and design of a complete wall. The publications also gives a short...

  15. Sheared solid materials

    Indian Academy of Sciences (India)

    Akira Onuki; Akira Furukawa; Akihiko Minami

    2005-05-01

    We present a time-dependent Ginzburg–Landau model of nonlinear elasticity in solid materials. We assume that the elastic energy density is a periodic function of the shear and tetragonal strains owing to the underlying lattice structure. With this new ingredient, solving the equations yields formation of dislocation dipoles or slips. In plastic flow high-density dislocations emerge at large strains to accumulate and grow into shear bands where the strains are localized. In addition to the elastic displacement, we also introduce the local free volume . For very small the defect structures are metastable and long-lived where the dislocations are pinned by the Peierls potential barrier. However, if the shear modulus decreases with increasing , accumulation of around dislocation cores eventually breaks the Peierls potential leading to slow relaxations in the stress and the free energy (aging). As another application of our scheme, we also study dislocation formation in two-phase alloys (coherency loss) under shear strains, where dislocations glide preferentially in the softer regions and are trapped at the interfaces.

  16. Laboratory observation of magnetic field growth driven by shear flow

    Energy Technology Data Exchange (ETDEWEB)

    Intrator, T. P., E-mail: intrator@lanl.gov; Feng, Y.; Sears, J.; Weber, T. [Los Alamos National Laboratory, M.S. E526, Los Alamos, New Mexico 87545 (United States); Dorf, L. [Applied Materials, Inc., Santa Clara, CA 95054 (United States); Sun, X. [University of Science and Technology, Hefei (China)

    2014-04-15

    Two magnetic flux ropes that collide and bounce have been characterized in the laboratory. We find screw pinch profiles that include ion flow v{sub i}, magnetic field B, current density J, and plasma pressure. The electron flow v{sub e} can be inferred, allowing the evaluation of the Hall J×B term in a two fluid magnetohydrodynamic Ohm's Law. Flux ropes that are initially cylindrical are mutually attracted and compress each other, which distorts the cylindrical symmetry. Magnetic field is created via the ∇×v{sub e}×B induction term in Ohm's Law where in-plane (perpendicular) shear of parallel flow (along the flux rope) is the dominant feature, along with some dissipation and magnetic reconnection. We predict and measure the growth of a quadrupole out-of-plane magnetic field δB{sub z}. This is a simple and coherent example of a shear flow driven dynamo. There is some similarity with two dimensional reconnection scenarios, which induce a current sheet and thus out-of-plane flow in the third dimension, despite the customary picture that considers flows only in the reconnection plane. These data illustrate a general and deterministic mechanism for large scale sheared flows to acquire smaller scale magnetic features, disordered structure, and possibly turbulence.

  17. Laboratory observation of magnetic field growth driven by shear flow

    Science.gov (United States)

    Intrator, T. P.; Dorf, L.; Sun, X.; Feng, Y.; Sears, J.; Weber, T.

    2014-04-01

    Two magnetic flux ropes that collide and bounce have been characterized in the laboratory. We find screw pinch profiles that include ion flow vi, magnetic field B, current density J, and plasma pressure. The electron flow ve can be inferred, allowing the evaluation of the Hall J ×B term in a two fluid magnetohydrodynamic Ohm's Law. Flux ropes that are initially cylindrical are mutually attracted and compress each other, which distorts the cylindrical symmetry. Magnetic field is created via the ∇×ve×B induction term in Ohm's Law where in-plane (perpendicular) shear of parallel flow (along the flux rope) is the dominant feature, along with some dissipation and magnetic reconnection. We predict and measure the growth of a quadrupole out-of-plane magnetic field δBz. This is a simple and coherent example of a shear flow driven dynamo. There is some similarity with two dimensional reconnection scenarios, which induce a current sheet and thus out-of-plane flow in the third dimension, despite the customary picture that considers flows only in the reconnection plane. These data illustrate a general and deterministic mechanism for large scale sheared flows to acquire smaller scale magnetic features, disordered structure, and possibly turbulence.

  18. Shear Thinning of Noncolloidal Suspensions

    Science.gov (United States)

    Vázquez-Quesada, Adolfo; Tanner, Roger I.; Ellero, Marco

    2016-09-01

    Shear thinning—a reduction in suspension viscosity with increasing shear rates—is understood to arise in colloidal systems from a decrease in the relative contribution of entropic forces. The shear-thinning phenomenon has also been often reported in experiments with noncolloidal systems at high volume fractions. However its origin is an open theoretical question and the behavior is difficult to reproduce in numerical simulations where shear thickening is typically observed instead. In this letter we propose a non-Newtonian model of interparticle lubrication forces to explain shear thinning in noncolloidal suspensions. We show that hidden shear-thinning effects of the suspending medium, which occur at shear rates orders of magnitude larger than the range investigated experimentally, lead to significant shear thinning of the overall suspension at much smaller shear rates. At high particle volume fractions the local shear rates experienced by the fluid situated in the narrow gaps between particles are much larger than the averaged shear rate of the whole suspension. This allows the suspending medium to probe its high-shear non-Newtonian regime and it means that the matrix fluid rheology must be considered over a wide range of shear rates.

  19. Shear strength of non-shear reinforced concrete elements

    DEFF Research Database (Denmark)

    Hoang, Cao linh

    1997-01-01

    The paper deals with the plastic shear strength of non shear reinforced T-beams.The influence of an un-reinforced flange on the shear capacity is investigated by considering a failure mechanism involving crack sliding in the web and a kind of membrane action over an effective width of the flange...

  20. Exact near-wall traveling waves of plane Poiseuille flow

    Science.gov (United States)

    Gibson, John; Brand, Evan

    2013-11-01

    We present several spatially-localized equilibrium and traveling-wave solutions of plane Couette and plane Poiseuille flow. The solutions consist of highly concentrated and spanwise-localized alternating streamwise rolls, centered over low-speed streamwise streaks and flanked on either side by high-speed streaks. For large Reynolds numbers the solutions develop critical layers that are concentrated at isolated points on the critical surface u = c . For several traveling-wave solutions of plane Poiseuille flow, the rolls are concentrated near one wall, producing streaks near the wall and larger reduction of the bulk flow in the core. These solutions form particularly isolated and elemental versions of near-wall coherent structures in shear flows and capture, as precise time-independent solutions of Navier-Stokes, the process by which near-wall rolls exchange momentum between the wall and core regions and thereby increase drag.

  1. Three-dimensional sheaf of ultrasound planes reconstruction (SOUPR) of ablated volumes.

    Science.gov (United States)

    Ingle, Atul; Varghese, Tomy

    2014-08-01

    This paper presents an algorithm for 3-D reconstruction of tumor ablations using ultrasound shear wave imaging with electrode vibration elastography. Radio-frequency ultrasound data frames are acquired over imaging planes that form a subset of a sheaf of planes sharing a common axis of intersection. Shear wave velocity is estimated separately on each imaging plane using a piecewise linear function fitting technique with a fast optimization routine. An interpolation algorithm then computes velocity maps on a fine grid over a set of C-planes that are perpendicular to the axis of the sheaf. A full 3-D rendering of the ablation can then be created from this stack of C-planes; hence the name "Sheaf Of Ultrasound Planes Reconstruction" or SOUPR. The algorithm is evaluated through numerical simulations and also using data acquired from a tissue mimicking phantom. Reconstruction quality is gauged using contrast and contrast-to-noise ratio measurements and changes in quality from using increasing number of planes in the sheaf are quantified. The highest contrast of 5 dB is seen between the stiffest and softest regions of the phantom. Under certain idealizing assumptions on the true shape of the ablation, good reconstruction quality while maintaining fast processing rate can be obtained with as few as six imaging planes suggesting that the method is suited for parsimonious data acquisitions with very few sparsely chosen imaging planes.

  2. Optimal disturbances in shearing and swirling flows

    Science.gov (United States)

    Daly, Conor

    2011-11-01

    Over the past twenty years transient energy density growth of linearly stable disturbances has shown to be the likely instigator for transition to turbulence in parallel shear flows. In this vein, optimal linear perturbations are calculated for two flows which have a mixture of forces acting on the fluid body. These are; rotating plane Couette flow (RPCF), which combines pressure-driven shear and swirl, and cylindrical Couette-Poiseuille flow (CCPF), which combines pressure-driven and Couette shear. Contours are presented of the maximum achievable linear transient growth, G, over the full range of wavenumbers within the linearly stable parameter regimes. Reference is made to experimental works on each flow and we examine the role that optimal disturbances have in the different transition phenomena that are observed. It is found that the contours of G fall qualitatively alongside the points of transition in the two flows, in support of the notion that large linear transient growth can act a precursor to transition. Despite the combination of effects acting on each fluid, transition in both flows falls in the range 102 flows the same mechanism may be at work. This work is funded by EPSRC.

  3. Resonant alignment of microswimmer trajectories in oscillatory shear flows

    Science.gov (United States)

    Hope, Alexander; Croze, Ottavio A.; Poon, Wilson C. K.; Bees, Martin A.; Haw, Mark D.

    2016-09-01

    Oscillatory flows are commonly experienced by swimming micro-organisms in the environment, industrial applications, and rheological investigations. We characterize experimentally the response of the alga Dunaliella salina to oscillatory shear flows and report the surprising discovery that algal swimming trajectories orient perpendicular to the flow-shear plane. The ordering has the characteristics of a resonance in the driving parameter space. The behavior is qualitatively reproduced by a simple model and simulations accounting for helical swimming, suggesting a mechanism for ordering and criteria for the resonant amplitude and frequency. The implications of this work for active oscillatory rheology and industrial algal processing are discussed.

  4. Surface Forces on a Deforming Ellipsoid in Shear Flow

    CERN Document Server

    Kightley, E P; Evans, J A; Bortz, D M

    2016-01-01

    We present a model for computing the surface force density on a fluid ellipsoid in simple shear flow, which we derive by coupling existing models for the shape of a fluid droplet and the surface force density on a solid ellipsoid. The primary contribution of this coupling is to develop a method to compute the force acting against a plane intersecting the ellipsoid, which we call the fragmentation force. The model can be used to simulate the motion, shape, surface force density, and breakage of fluid droplets and colloidal aggregates in shear flow.

  5. Transverse Shear Behavior of a Nomex Core for Sandwich Panels

    Science.gov (United States)

    Nasir, M. A.; Khan, Z.; Farooqi, I.; Nauman, S.; Anas, S.; Khalil, S.; Pasha, A.; Khan, Z.; Shah, M.; Qaiser, H.; Ata, R.

    2015-01-01

    The out-of-plane transverse shear characteristics of a Nomex honeycomb core have been studied. Finite-element analyses were performed to find the equivalent transverse shear moduli of the honeycomb core by using a unit-cell-based modeling approach with account of the orthotropic nature of Nomex paper. The results obtained are compared with those of three theoretical approaches. The differences between the numerical and theoretical results are attributed to the isotropic behavior of the basic core material considered in the theoretical approaches.

  6. Resonant alignment of microswimmer trajectories in oscillatory shear flows

    CERN Document Server

    Hope, Alexander; Poon, Wilson C K; Bees, Martin A; Haw, Mark D

    2015-01-01

    Oscillatory flows are common in the environment, industrial applications and rheological investigations. We experimentally characterise the response of the alga {\\it Dunaliella salina} to oscillatory shear and squeeze flows, and report the surprising discovery that algal swimming trajectories orient perpendicular to the flow-shear plane. The ordering has the characteristics of a resonance in the driving parameter space, which is qualitatively reproduced by a model accounting for helical swimming. Our discovery challenges current understanding of swimmers in flows and provides the foundations for the oscillatory rheology of active suspensions, of particular relevance to algal processing applications.

  7. Local Reynolds number and thresholds of transition in shear flows

    Science.gov (United States)

    Tao, JianJun; Chen, ShiYi; Su, WeiDong

    2013-02-01

    Recent experimental and numerical investigations reveal that the onset of turbulence in plane-Poiseuille flow and plane-Couette flow has some similar stages separated with different threshold Reynolds numbers. Based on these observations and the energy equation of a disturbed fluid element, a local Reynolds number Re L is derived to represent the maximum ratio of the energy supplement to the energy dissipation in a cross section. It is shown that along the sequence of transition stages, which include transient localized turbulence, "equilibrium" localized turbulence, spatially intermittent but temporally persistent turbulence and uniform turbulence, the corresponding thresholds of Re L for plane-Couette flow, Hagen-Poiseuille flow and plane-Poiseuille flow are consistent, indicating that the critical (threshold) states during the laminar-turbulent transition are determined by the local properties of the base flow and are independent of global features, such as flow geometries (pipe or channel) and types of driving forces (shear driving or pressure driving).

  8. An experimental and numerical study of confined non-reacting and reacting turbulent jets to facilitate homogeneous combustion in industrial furnaces

    Science.gov (United States)

    Lee, Insu

    Confined non-reacting turbulent jets are ideal for recirculating the hot flue gas back into the furnace from an external exhaust duct. Such jets are also used inside the furnace to internally entrain and recirculate the hot flue gas to preheat and dilute the reactants. Both internal and external implementation of confined turbulent jets increase the furnace thermal efficiency. For external implementation, depending on the circumstances, the exhaust gas flow may be co- or counter-flow relative to the jet flow. Inside the furnaces, fuel and air jets are injected separately. To create a condition which can facilitate near homogeneous combustion, these jets have to first mix with the burned gas inside the furnace and simultaneously being heated and diluted prior to combustion. Clearly, the combustion pattern and emissions from reacting confined turbulent jets are affected by jet interactions, mixing and entrainment of hot flue gas. In this work, the flow and mixing characteristics of a non-reacting and reacting confined turbulent jet are investigated experimentally and numerically. This work consists of two parts: (i) A study of flow and mixing characteristics of non-reacting confined turbulent jets with co- or counter-flowing exhaust/flue gas. Here the axial and radial distributions of temperature, velocity and NO concentration (used as a tracer gas) were measured. FLUENT was used to numerically simulate the experimental results. This work provides the basic understanding of the flow and mixing characteristics of confined turbulent jets and develops some design considerations for recirculating flue gas back into the furnace as expressed by the recirculation zone and the stagnation locations. (ii) Numerical calculations of near homogeneous combustion are performed for the existing furnace. The exact geometry of the furnace in the lab is used and the real dimensional boundary conditions are considered. The parameters such as air nozzle diameter (dair), fuel nozzle

  9. Shear Behavior of Concrete Beams Reinforced with GFRP Shear Reinforcement

    OpenAIRE

    Heecheul Kim; Min Sook Kim; Myung Joon Ko; Young Hak Lee

    2015-01-01

    This paper presents the shear capacities of concrete beams reinforced with glass fiber reinforced polymer (GFRP) plates as shear reinforcement. To examine the shear performance, we manufactured and tested a total of eight specimens. Test variables included the GFRP strip-width-to-spacing ratio and type of opening array. The specimen with a GFRP plate with a 3×2 opening array showed the highest shear strength. From the test results, the shear strength increased as the strip-width-to-strip-spac...

  10. Shear Behavior of Concrete Beams Reinforced with GFRP Shear Reinforcement

    Directory of Open Access Journals (Sweden)

    Heecheul Kim

    2015-01-01

    Full Text Available This paper presents the shear capacities of concrete beams reinforced with glass fiber reinforced polymer (GFRP plates as shear reinforcement. To examine the shear performance, we manufactured and tested a total of eight specimens. Test variables included the GFRP strip-width-to-spacing ratio and type of opening array. The specimen with a GFRP plate with a 3×2 opening array showed the highest shear strength. From the test results, the shear strength increased as the strip-width-to-strip-spacing ratio increased. Also, we used the experimental results to evaluate whether the shear strength equations of ACI 318-14 and ACI 440.1R can be applied to the design of GFRP shear reinforcement. In the results, the ACI 440 equation underestimated the experimental results more than that of ACI 318.

  11. Gold mineralization in the West Hoggar shear zone, Algeria

    Science.gov (United States)

    Ferkous, K.; Leblanc, M.

    1995-06-01

    The Amesmessa gold prospect is located along a vertical N-S-trending crustal-scale ductile shear zone; stretching lineations are subhorizontal. This major shear zone is a Late Pan African dextral strike-slip fault of the Pharusian Belt of the Tuareg Shield (Algeria). The Amesmessa shear zone is asymmetric: strong thermal and deformational gradients are present along its western border where biotitic ultramylonites are in contact with a rigid Archean complex (In Ouzzal block), whereas there is a progressive gradation, through mylonite then protomylonite, to the Proterozoic gneiss of the Eastern block which displays co-axial Pan African structures. The Amesmessa shear zone is characterized by the presence of a felsic dike complex emplaced during shearing, and forming the most important parent material for ultramylonites. Basic magmas and carbonatites also intruded within the shear zone. The gold-rich quartz veins are located within the ultramylonitic western part of the shear zone. These N-S-trending laminated quartz veins formed during the late increments of shearing (plastic/brittle transition), by repeated syntectonic hydraulic fracturing along zones of rheological contrast parallel to foliation. The ore mineral association (pyrite, galena, native gold, sphalerite) crystallized in the deformed quartz matrix along late shear planes. Undeformed E-W trending banded quartz veins are present in the mylonitic eastern part of the shear zone; their gold content is low and no native gold has been observed. A strong hydrothermal alteration resulted in the development (along the walls of the N-S gold-bearing quartz veins) of a 5-m-wide carbonate-sericite-albite-pyrite secondary mineral association which implies an important CO2 supply and moderate temperature conditions. There is no alteration halo around the E-W quartz veins. Ultramylonites, hydrothermally altered rocks and quartz veins display similar REE patterns characterized by strong LREE enrichments. Shear

  12. Gelation under shear

    Energy Technology Data Exchange (ETDEWEB)

    Butler, B.D.; Hanley, H.J.M.; Straty, G.C. [National Institute of Standards and Technology, Boulder, CO (United States); Muzny, C.D. [Univ. of Colorado, Boulder, CO (United States)

    1995-12-31

    An experimental small angle neutron scattering (SANS) study of dense silica gels, prepared from suspensions of 24 nm colloidal silica particles at several volume fractions {theta} is discussed. Provided that {theta}{approx_lt}0.18, the scattered intensity at small wave vectors q increases as the gelation proceeds, and the structure factor S(q, t {yields} {infinity}) of the gel exhibits apparent power law behavior. Power law behavior is also observed, even for samples with {theta}>0.18, when the gel is formed under an applied shear. Shear also enhances the diffraction maximum corresponding to the inter-particle contact distance of the gel. Difficulties encountered when trying to interpret SANS data from these dense systems are outlined. Results of computer simulations intended to mimic gel formation, including computations of S(q, t), are discussed. Comments on a method to extract a fractal dimension characterizing the gel are included.

  13. Plane Mercury librations

    Science.gov (United States)

    Barkin, Yu. V.; Ferrandiz, J. M.

    2009-04-01

    theory of Mercury librations in longitude by using three characteristics of Mercury rotation determined in the paper [3]. Two from these parameters are values of angle of librations in longitude and angular velocity in moment of passage of perihelion of Mercury orbit on 17 April 2002: (^g)0 = 0007 ± 0001, (^?•? )0 = (2.10± 0.06)•? ars/d. Third parameter determined in [3] is a dynamical coefficient: K = (B -A)•(4Cm ) = (5.08± 0.30) × 10-5. B > A are principal moment of inertia, corresponding to equatorial axes of inertia; Cm is a polar moment of inertia of the mantle of Mercury. 1 Analytical theory of plane Mercury librations. This theory describes forced and free librations of Mercury in longitude in the frame of plane problem about resonant librations of Mercury considered or as non-spherical rigid body, or as system of rigid non-spherical mantle and liquid ellipsoidal core. Saving the main terms for the perturbations of angle of librations ^g and angular velocity ^? in both mentioned cases we will have formulae [6]: ^g = K(E sin M + E sin2M + E sin 3M + E sin4M + E sin5M ) 1 2 3 4 5+K0 sin(E šKM- - φ) (A)

  14. Shear Roll Mill Reactivation

    Science.gov (United States)

    2012-09-13

    accommodate a trial run of inert single base pellet feed for use in a twin screw extruder. 15. SUBJECT TERMS INIT248, Advanced Propellant Technology...Bldg. 4909-5 – Shear Roll Mill Pilot Plant at the Radford Army Ammunition Plant (RFAAP) in order to produce pellet feed for a twin screw extruder used...propellant to simulate feed for a twin screw extruder. Preventive maintenance procedures were in progress in final preparation for running with

  15. Gravitational Couplings for Gop-Planes and y-Op-Planes

    CERN Document Server

    Ospina-Giraldo, J F

    2000-01-01

    The Wess-Zumino actions for generalized orientifold planes (GOp-planes) and y-deformed orientifold planes (yOp-planes) are presented and two series power expantions are realized from whiches processes that involves GOp-planes,yOp-planes, RR-forms, gravitons and gaugeons, are obtained. Finally non-standard GOp-planes and y-Op-planes are showed.

  16. Large-scale instability in a sheared nonhelical turbulence: Formation of vortical structures.

    Science.gov (United States)

    Elperin, Tov; Golubev, Ilia; Kleeorin, Nathan; Rogachevskii, Igor

    2007-12-01

    We study a large-scale instability in a sheared nonhelical turbulence that causes generation of large-scale vorticity. Three types of the background large-scale flows are considered, i.e., the Couette and Poiseuille flows in a small-scale homogeneous turbulence, and the "log-linear" velocity shear in an inhomogeneous turbulence. It is known that laminar plane Couette flow and antisymmetric mode of laminar plane Poiseuille flow are stable with respect to small perturbations for any Reynolds numbers. We demonstrate that in a small-scale turbulence under certain conditions the large-scale Couette and Poiseuille flows are unstable due to the large-scale instability. This instability causes formation of large-scale vortical structures stretched along the mean sheared velocity. The growth rate of the large-scale instability for the "log-linear" velocity shear is much larger than that for the Couette and Poiseuille background flows. We have found a turbulent analogue of the Tollmien-Schlichting waves in a small-scale sheared turbulence. A mechanism of excitation of turbulent Tollmien-Schlichting waves is associated with a combined effect of the turbulent Reynolds stress-induced generation of perturbations of the mean vorticity and the background sheared motions. These waves can be excited even in a plane Couette flow imposed on a small-scale turbulence when perturbations of mean velocity depend on three spatial coordinates. The energy of these waves is supplied by the small-scale sheared turbulence.

  17. Compressibility effects in the shear layer over a rectangular cavity

    Energy Technology Data Exchange (ETDEWEB)

    Beresh, Steven J.; Wagner, Justin; Casper, Katya Marie

    2016-10-26

    we studied the influence of compressibility on the shear layer over a rectangular cavity of variable width in a free stream Mach number range of 0.6–2.5 using particle image velocimetry data in the streamwise centre plane. As the Mach number increases, the vertical component of the turbulence intensity diminishes modestly in the widest cavity, but the two narrower cavities show a more substantial drop in all three components as well as the turbulent shear stress. Furthermore, this contrasts with canonical free shear layers, which show significant reductions in only the vertical component and the turbulent shear stress due to compressibility. The vorticity thickness of the cavity shear layer grows rapidly as it initially develops, then transitions to a slower growth rate once its instability saturates. When normalized by their estimated incompressible values, the growth rates prior to saturation display the classic compressibility effect of suppression as the convective Mach number rises, in excellent agreement with comparable free shear layer data. The specific trend of the reduction in growth rate due to compressibility is modified by the cavity width.

  18. Shear-stress-controlled dynamics of nematic complex fluids.

    Science.gov (United States)

    Klapp, Sabine H L; Hess, Siegfried

    2010-05-01

    Based on a mesoscopic theory we investigate the nonequilibrium dynamics of a sheared nematic liquid, with the control parameter being the shear stress σ xy (rather than the usual shear rate, γ). To this end we supplement the equations of motion for the orientational order parameters by an equation for γ, which then becomes time dependent. Shearing the system from an isotropic state, the stress-controlled flow properties turn out to be essentially identical to those at fixed γ. Pronounced differences occur when the equilibrium state is nematic. Here, shearing at controlled γ yields several nonequilibrium transitions between different dynamic states, including chaotic regimes. The corresponding stress-controlled system has only one transition from a regular periodic into a stationary (shear-aligned) state. The position of this transition in the σ xy-γ plane turns out to be tunable by the delay time entering our control scheme for σ xy. Moreover, a sudden change in the control method can stabilize the chaotic states appearing at fixed γ.

  19. Multiphysics Simulations of Entrained Flow Gasification. Part I: Validating the Nonreacting Flow Solver and the Particle Turbulent Dispersion Model

    KAUST Repository

    Kumar, Mayank

    2012-01-19

    In this two-part paper, we describe the construction, validation, and application of a multiscale model of entrained flow gasification. The accuracy of the model is demonstrated by (1) rigorously constructing and validating the key constituent submodels against relevant canonical test cases from the literature and (2) validating the integrated model against experimental data from laboratory scale and commercial scale gasifiers. In part I, the flow solver and particle turbulent dispersion models are validated against experimental data from nonswirling flow and swirling flow test cases in an axisymmetric sudden expansion geometry and a two-phase flow test case in a cylindrical bluff body geometry. Results show that while the large eddy simulation (LES) performs best among all tested models in predicting both swirling and nonswirling flows, the shear stress transport (SST) k-ω model is the best choice among the commonly used Reynolds-averaged Navier-Stokes (RANS) models. The particle turbulent dispersion model is accurate enough in predicting particle trajectories in complex turbulent flows when the underlying turbulent flow is well predicted. Moreover, a commonly used modeling constant in the particle dispersion model is optimized on the basis of comparisons with particle-phase experimental data for the two-phase flow bluff body case. © 2011 American Chemical Society.

  20. Numerical simulation of reacting and non-reacting flow in a combustion chamber; Numerisk simulering av reagerande och icke-reagerande stroemning i en braennkammare

    Energy Technology Data Exchange (ETDEWEB)

    Borg, A.; Revstedt, J.

    1996-04-01

    The purpose of this work has been to do a preliminary study of how well numerical calculations with different turbulence models can predict the flow and temperature fields of a strongly swirling and combusting flow in an experimental combustion chamber and to see which parameters in the mathematical model are the most important. The combustion chamber on which we have done the calculations is called Validation Rig II and was designed by Volvo Aero Corporation. The main part of the study has been carried out on a non-reacting flow but some work has also been done on reacting flow. In most cases it has not been meaningful to compare the calculations with the measurements because they differ quite a lot from each other. For the non-reacting case the following investigations have been made: * How the solution differs for different turbulence models, * The solutions sensitivity to inlet boundary conditions, * How different types of leakage disturb the flow, and * The difference in results between two different CFD-codes, the commercial code CFDS-Flow3D and a code developed at the department of fluid mechanics. For the reacting cases we have studied the influence of: * one or two reaction steps, * the effects of a change in reaction rate, * the influence of thermal radiation, and * the effects of changing the boundary conditions for temperature on the walls. The results from these calculations show that the inlet turbulence intensity has very little effect on the values of the turbulent quantities as well as the velocity profiles at the outlet. Changing the turbulence model or the outlet boundary conditions gives some change in velocity profiles at the outlet but only marginal effects on the swirl number. 21 refs, 54 figs, 19 tabs

  1. Evolutes of Hyperbolic Plane Curves

    Institute of Scientific and Technical Information of China (English)

    Shyuichi IZUMIYA; Dong He PEI; Takashi SANO; Erika TORII

    2004-01-01

    We define the notion of evolutes of curves in a hyperbolic plane and establish the relationships between singularities of these subjects and geometric invariants of curves under the action of the Lorentz group. We also describe how we can draw the picture of an evolute of a hyperbolic plane curve in the Poincar(e) disk.

  2. Conceptual Design of Wave Plane

    DEFF Research Database (Denmark)

    Frigaard, Peter; Trewers, Andrew; Kofoed, Jens Peter;

    The Wave Plane is a patented Wave Energy device of the overtopping type, designed to capture potential as well as kinetic energy. This is as such different to other overtopping devices, who usually only focus on potential energy. If Wave Plane A/S can deliver the turbine technology to utilize both...

  3. Shear stress distribution and characteristics of deformation for shear band-elastic body system at pre-peak and post-peak

    Institute of Scientific and Technical Information of China (English)

    WANG Xue-bin

    2005-01-01

    The distributed shear stress and the displacement across shear band, the evolution of plastic zones, and the load-carrying capacity of rock specimen were investigated in plane strain direct shear test according to Fast Lagrangian Analysis of Continua (FLAC). And then the shear displacement distribution in normal direction of system composed of localized shear band and elastic rock was analyzed based on gradient-dependent plasticity. The adopted failure criterion was a composite of Mohr-Coulomb criterion, that is, the relation between tension cut-off and post-peak constitutive of rock was linear strain-softening. Numerical results show that shear stress field approximately undergoes three different stages. At first, shear stress is only concentrated in the middle of top and base of specimen. Next, shear stress in the middle of specimen tends to increase, owing to superposition of shear stresses. Interestingly, two peaks of shear stress appear far from the loading ends of specimen, and the peaks approach with the increase in timestep until elements at the center of specimen yield. Finally, relatively lower shear stress level is reached in large part of specimen except in the regions near the two ends. As flow stress decreases, the analytical shear displacement distribution in shear band based on gradient-dependent plasticity becomes steep; outside the band, it is linear and its slope tends to decrease. These theoretical results qualitatively agree with that of the present numerical predicted results. Main advantage of the analytical solution over the numerical results according to FLAC is that it is continuous, smooth and non-linear (except at elastic stage).

  4. Magnetic field generation from shear flow in flux ropes

    Science.gov (United States)

    Intrator, T. P.; Sears, J.; Gao, K.; Klarenbeek, J.; Yoo, C.

    2012-10-01

    In the Reconnection Scaling Experiment (RSX) we have measured out of plane quadrupole magnetic field structure in situations where magnetic reconnection was minimal. This quadrupole out of plane magnetic signature has historically been presumed to be the smoking gun harbinger of reconnection. On the other hand, we showed that when flux ropes bounced instead of merging and reconnecting, this signature could evolve. This can follow from sheared fluid flows in the context of a generalized Ohms Law. We reconstruct a shear flow model from experimental data for flux ropes that have been experimentally well characterized in RSX as screw pinch equilibria, including plasma ion and electron flow, with self consistent profiles for magnetic field, pressure, and current density. The data can account for the quadrupole field structure.

  5. Construction-friendly ductile shear joints for precast concrete panels

    DEFF Research Database (Denmark)

    Sørensen, Jesper Harrild; Hoang, Linh Cao; Fischer, Gregor

    2015-01-01

    The scope of this paper is the shear capacity of in-situ cast joints between precast concrete panels. Current practice with vertical lowering of the wall panels experiences difficulties in the assembly phase, since the traditional U-bar connection requires an overlap in a horizontal plane to allow...... a construction-friendly design with U-bars overlapping in the same plane as the panel itself. The design allows for a trouble-free vertical lowering of the panels without pre or post processing of the preinstalled reinforcement loops. Furthermore, an overall more ductile behavior of the joint is obtained....... The solution is tested in a push-off experimental setup and the influence of important geometric parameters of the keyed shear joint is investigated. The first peak load carrying capacity is assessed using plasticity models, and the failure modes are identified by the use of digital image correlation...

  6. Transverse electron-scale instability in relativistic shear flows

    CERN Document Server

    Alves, E P; Fonseca, R A; Silva, L O

    2015-01-01

    Electron-scale surface waves are shown to be unstable in the transverse plane of a shear flow in an initially unmagnetized plasma, unlike in the (magneto)hydrodynamics case. It is found that these unstable modes have a higher growth rate than the closely related electron-scale Kelvin-Helmholtz instability in relativistic shears. Multidimensional particle-in-cell simulations verify the analytic results and further reveal the emergence of mushroom-like electron density structures in the nonlinear phase of the instability, similar to those observed in the Rayleigh Taylor instability despite the great disparity in scales and different underlying physics. Macroscopic ($\\gg c/\\omega_{pe}$) fields are shown to be generated by these microscopic shear instabilities, which are relevant for particle acceleration, radiation emission and to seed MHD processes at long time-scales.

  7. Anomalous diffusion of proteins in sheared lipid membranes

    CERN Document Server

    Khoshnood, Atefeh

    2013-01-01

    We use coarse grained molecular dynamics simulations to investigate diffusion properties of sheared lipid membranes with embedded transmembrane proteins. In membranes without proteins, we find normal in-plane diffusion of lipids in all flow conditions. Protein embedded membranes behave quite differently: by imposing a simple shear flow and sliding the monolayers of the membrane over each other, the motion of protein clusters becomes strongly superdiffusive in the shear direction. In such a circumstance, subdiffusion regime is predominant perpendicular to the flow. We show that superdiffusion is a result of accelerated chaotic motions of protein--lipid complexes within the membrane voids, which are generated by hydrophobic mismatch or the transport of lipids by proteins.

  8. Plasticity Approach to Shear Design

    DEFF Research Database (Denmark)

    Hoang, Cao Linh; Nielsen, Mogens Peter

    1998-01-01

    The paper presents some plastic models for shear design of reinforced concrete beams. Distinction is made between two shear failure modes, namely web crushing and crack sliding. The first mentioned mode is met in beams with large shear reinforcement degrees. The mode of crack sliding is met in no...... in uncracked concrete. Good agree between theory and tests has been found.Keywords: dsign, plasticity, reinforced concrete, reinforcement, shear, web crushing.......The paper presents some plastic models for shear design of reinforced concrete beams. Distinction is made between two shear failure modes, namely web crushing and crack sliding. The first mentioned mode is met in beams with large shear reinforcement degrees. The mode of crack sliding is met in non......-shear reinforced beams as well as in lightly shear reinforced beams. For such beams the shear strength is determined by the recently developed crack sliding model. This model is based upon the hypothesis that cracks can be transformed into yield lines, which have lower sliding resistance than yield lines formed...

  9. Direct numerical simulation of turbulent plane Couette flow

    Science.gov (United States)

    Lee, Moon Joo

    1991-01-01

    Turbulent plane Couette flow was numerically simulated at a Reynolds number (U(sub w)h/nu) of 6000, where U(sub w) is the relative wall speed and h is half the channel-height. Unlike in Poiseuille flow, where the mean shear rate changes its sign at the centerline, the sign of mean shear rate in plane Couette flow remains the same across the whole channel. This difference is expected to yield several differences between the two flows, especially in the core region. The most significant and dramatic difference observed was the existence of large-scale structures in the core region of the plane Couette flow. The large eddies are extremely long in the flow direction and fill the entire channel (i.e., their vertical extent is 2h). The large-scale structures have the largest contribution from the wavenumber (k(sub x)h,k(sub z)h) = (0, plus or minus 1.5), corresponding to a wavelength lambda(sub z)/h is approximately equal to 4. The secondary motion associated with the k(sub x)h = 0 mode consists of the large-scale vortices. The large eddies contribute about 30 percent of turbulent kinetic energy.

  10. Matrix cracking of fiber-reinforced ceramic composites in shear

    Science.gov (United States)

    Rajan, Varun P.; Zok, Frank W.

    2014-12-01

    The mechanics of cracking in fiber-reinforced ceramic matrix composites (CMCs) under general loadings remains incomplete. The present paper addresses one outstanding aspect of this problem: the development of matrix cracks in unidirectional plies under shear loading. To this end, we develop a model based on potential energy differences upstream and downstream of a fully bridged steady-state matrix crack. Through a combination of analytical solutions and finite element simulations of the constituent stresses before and after cracking, we identify the dominant stress components that drive crack growth. We show that, when the axial slip lengths are much larger than the fiber diameter and when interfacial slip precedes cracking, the shear stresses in the constituents are largely unaffected by the presence of the crack; the changes that do occur are confined to a 'core' region within a distance of about one fiber diameter from the crack plane. Instead, the driving force for crack growth derives mainly from the axial stresses-tensile in the fibers and compressive in the matrix-that arise upon cracking. These stresses are well-approximated by solutions based on shear-lag analysis. Combining these solutions with the governing equation for crack growth yields an analytical estimate of the critical shear stress for matrix cracking. An analogous approach is used in deriving the critical stresses needed for matrix cracking under arbitrary in-plane loadings. The applicability of these results to cross-ply CMC laminates is briefly discussed.

  11. Mode Ⅱ fracture mechanism of direct shearing specimen with guiding grooves of rock

    Institute of Scientific and Technical Information of China (English)

    饶秋华; 孙宗颀; 王桂尧; 徐纪成; 张静宜

    2001-01-01

    Fracture mechanism of direct shear specimen with guiding grooves of rock was investigated experimentally and numerically in order to explore a favorable stress condition for creating Mode Ⅱ fracture and guide design of specimen configuration for determining Mode Ⅱ fracture toughness of rock, KⅡC. The experimental and numerical results demonstrate that Mode Ⅱ fracture can be successfully achieved in the direct shearing specimen with guiding groove because the guiding grooves added in the notch plane can generate a favorable stress condition for Mode Ⅱ fracture, i.e. tensile stress at the notch tip is completely depressed and shear stress at the notch tip is very high in the notch plane. The optimum design of the specimen configuration for KⅡC testing should aim to reduce tensile stress to be compressive stress or be lower than tensile strength and greatly increase shear stress at crack tip.

  12. The velocity shear and vorticity across redshifts and non-linear scales

    CERN Document Server

    Libeskind, Noam I; Gottlöber, Stefan

    2013-01-01

    The evolution of the large scale distribution of matter in the universe is often characterized by the density field. Here we take a complimentary approach and characterize it using the cosmic velocity field, specifically the deformation of the velocity field. The deformation tensor is decomposed into its symmetric component (known as the "shear tensor") and its anti-symmetric part (the "vorticity"). Using a high resolution cosmological simulation we examine the relative orientations of the shear and the vorticity as a function of spatial scale and redshift. The shear is found to be remarkable stable to the choice of scale, while the vorticity is found to quickly decay with increasing spatial scale or redshift. The vorticity emerges out of the linear regime randomly oriented with respect to the shear eigenvectors. Non-linear evolution drives the vorticity to lie within the plane defined by the eigenvector of the fastest collapse. Within that plane the vorticity first gets aligned with the middle eigenvector an...

  13. Wind shear test

    Science.gov (United States)

    Techniques for forecasting and detecting a type of wind shear called microbursts are being tested this month in an operational program at Denver's Stapleton International Airport as part of an effort to reduce hazards to airplanes and passengers.Wind shear, which can be spawned by convective storms, can occur as a microburst. These downbursts of cool air are usually recognizable as a visible rain shaft beneath a thundercloud. Sometimes, however, the rain shaft evaporates before reaching the ground, leaving the downdraft invisible. Although thunderstorms are traditionally avoided by airplane pilots, these invisible downdrafts also harbor hazards in what usually appear to be safe skies. When the downdraft reaches the earth's surface, the downdraft spreads out horizontally, much like a stream of water gushing from a garden hose on a concrete surface, explained John McCarthy, director of the operational program. Airplanes can encounter trouble when the downdraft from the microburst causes sudden shifts in wind direction, which may reduce lift on the wing, an especially dangerous situation during takeoff.

  14. Effect of single-particle magnetostriction on the shear modulus of compliant magnetoactive elastomers

    OpenAIRE

    Kalita, Viktor; Snarskii, Andrew; Shamonin, Mikhail; Zorinets, Denys

    2017-01-01

    The influence of an external magnetic field on the static shear strain and the effective shear modulus of a magnetoactive elastomer (MAE) is studied theoretically in the framework of a recently introduced approach to the single-particle magnetostriction mechanism [V. M. Kalita et al, Phys. Rev. E 93, 062503 (2016)]. The planar problem of magnetostriction in an MAE with soft magnetic inclusions in the form of a thin disk (platelet) having the magnetic anisotropy in the plane of this disk is so...

  15. Inductive shearing of drilling pipe

    Energy Technology Data Exchange (ETDEWEB)

    Ludtka, Gerard M.; Wilgen, John; Kisner, Roger; Mcintyre, Timothy

    2016-04-19

    Induction shearing may be used to cut a drillpipe at an undersea well. Electromagnetic rings may be built into a blow-out preventer (BOP) at the seafloor. The electromagnetic rings create a magnetic field through the drillpipe and may transfer sufficient energy to change the state of the metal drillpipe to shear the drillpipe. After shearing the drillpipe, the drillpipe may be sealed to prevent further leakage of well contents.

  16. Inductive shearing of drilling pipe

    Science.gov (United States)

    Ludtka, Gerard M.; Wilgen, John; Kisner, Roger; Mcintyre, Timothy

    2016-04-19

    Induction shearing may be used to cut a drillpipe at an undersea well. Electromagnetic rings may be built into a blow-out preventer (BOP) at the seafloor. The electromagnetic rings create a magnetic field through the drillpipe and may transfer sufficient energy to change the state of the metal drillpipe to shear the drillpipe. After shearing the drillpipe, the drillpipe may be sealed to prevent further leakage of well contents.

  17. Failure During Sheared Edge Stretching

    Science.gov (United States)

    Levy, B. S.; van Tyne, C. J.

    2008-12-01

    Failure during sheared edge stretching of sheet steels is a serious concern, especially in advanced high-strength steel (AHSS) grades. The shearing process produces a shear face and a zone of deformation behind the shear face, which is the shear-affected zone (SAZ). A failure during sheared edge stretching depends on prior deformation in the sheet, the shearing process, and the subsequent strain path in the SAZ during stretching. Data from laboratory hole expansion tests and hole extrusion tests for multiple lots of fourteen grades of steel were analyzed. The forming limit curve (FLC), regression equations, measurement uncertainty calculations, and difference calculations were used in the analyses. From these analyses, an assessment of the primary factors that contribute to the fracture during sheared edge stretching was made. It was found that the forming limit strain with consideration of strain path in the SAZ is a major factor that contributes to the failure of a sheared edge during stretching. Although metallurgical factors are important, they appear to play a somewhat lesser role.

  18. Seismic shear waves as Foucault pendulum

    Science.gov (United States)

    Snieder, Roel; Sens-Schönfelder, Christoph; Ruigrok, Elmer; Shiomi, Katsuhiko

    2016-03-01

    Earth's rotation causes splitting of normal modes. Wave fronts and rays are, however, not affected by Earth's rotation, as we show theoretically and with observations made with USArray. We derive that the Coriolis force causes a small transverse component for P waves and a small longitudinal component for S waves. More importantly, Earth's rotation leads to a slow rotation of the transverse polarization of S waves; during the propagation of S waves the particle motion behaves just like a Foucault pendulum. The polarization plane of shear waves counteracts Earth's rotation and rotates clockwise in the Northern Hemisphere. The rotation rate is independent of the wave frequency and is purely geometric, like the Berry phase. Using the polarization of ScS and ScS2 waves, we show that the Foucault-like rotation of the S wave polarization can be observed. This can affect the determination of source mechanisms and the interpretation of observed SKS splitting.

  19. Behaviour of voids in a shear field

    DEFF Research Database (Denmark)

    Tvergaard, Viggo

    2009-01-01

    to a plane connecting the ends of the micro-crack is used as an approximate representation of contact stresses during frictionless sliding. In a previous study of the same problem the author applied hydrostatic pressure inside the nearly closed micro-crack to approximate contact conditions. The transverse...... surface loads used in the present analyses avoid the tendency to unrealistically elongate the voids. It is found that even though the model applied here gives significantly later occurrence of a maximum overall shear stress than that found by using hydrostatic pressure, the present model does predict...... a maximum in all the cases analyzed and thus illustrates the micro-mechanism leading to failure of the material by localization of plastic flow....

  20. Acoustic excitation of diffusion flames with coherent structure in a plane shear layer. ; Application of active combustion control to two-dimensional phase-locked arranging measurements. Soshiki kozo wo tomonau heimen sendai kakusan kaen no onkyo reiki. ; Nijigen iso heikin bunpu sokutei eno active nensho seigyo no oyo

    Energy Technology Data Exchange (ETDEWEB)

    Ishino, Y.; Kojima, T.; Oiwa, N.; Yamaguchi, S. (Nagoya Institute of Technology, Nagoya (Japan))

    1993-11-25

    The acoustic excitation of a plane diffusion flame enhances the periodicity of organized eddy controlled combustion. In this study, to clarify an effectiveness of application of active combustion control, phase characteristics of the excited eddy flames with high periodicity have been examined. A computer-aided phase-locked averaging method was employed to obtain graphical two-dimensional contour maps of the instantaneous profiles of temperature and CH emission. Both maps consisting of eight consecutive phases indicated clearly not only the periodic behavior of the organized eddy flame, but also the gas dynamic properties peculiar to those flames with coherent structure. In addition, the profiles of local contribution of the sound field to the combustion process were examined by calculating the two-dimensional distribution of the local Rayleigh index. Calculation results of the two-dimensional distribution of the local Rayleigh index indicated that the organized eddy flames have high sensitivity to sound, and play an important role in an interaction of sound and flame. 6 refs., 9 figs.

  1. Composite Interlaminar Shear Fracture Toughness, G(sub 2c): Shear Measurement of Sheer Myth?

    Science.gov (United States)

    OBrien, T. Kevin

    1997-01-01

    The concept of G2c as a measure of the interlaminar shear fracture toughness of a composite material is critically examined. In particular, it is argued that the apparent G2c as typically measured is inconsistent with the original definition of shear fracture. It is shown that interlaminar shear failure actually consists of tension failures in the resin rich layers between plies followed by the coalescence of ligaments created by these failures and not the sliding of two planes relative to one another that is assumed in fracture mechanics theory. Several strain energy release rate solutions are reviewed for delamination in composite laminates and structural components where failures have been experimentally documented. Failures typically occur at a location where the mode 1 component accounts for at least one half of the total G at failure. Hence, it is the mode I and mixed-mode interlaminar fracture toughness data that will be most useful in predicting delamination failure in composite components in service. Although apparent G2c measurements may prove useful for completeness of generating mixed-mode criteria, the accuracy of these measurements may have very little influence on the prediction of mixed-mode failures in most structural components.

  2. Energy flow analysis of out-of-plane vibration in coplanar coupled finite Mindlin plates

    Directory of Open Access Journals (Sweden)

    Park Young-Ho

    2015-01-01

    Full Text Available In this paper, an Energy Flow Analysis (EFA for coplanar coupled Mindlin plates was performed to estimate their dynamic responses at high frequencies. Mindlin plate theory can consider the effects of shear distortion and rotatory inertia, which are very important at high frequencies. For EFA for coplanar coupled Mindlin plates, the wave transmission and reflection relationship for progressing out-of-plane waves (out-of-plane shear wave, bending dominant flexural wave, and shear dominant flexural wave in coplanar coupled Mindlin plates was newly derived. To verify the validity of the EFA results, numerical analyses were performed for various cases where coplanar coupled Mindlin plates are excited by a harmonic point force, and the energy flow solutions for coplanar coupled Mindlin plates were compared with the classical solutions in the various conditions.

  3. Shear strength of non-shear reinforced concrete elements

    DEFF Research Database (Denmark)

    Hoang, Cao linh

    1997-01-01

    The paper deals with the shear strength of prestressed hollow-core slabs determined by the theory of plasticity. Two failure mechanisms are considered in order to derive the solutions.In the case of sliding failure in a diagonal crack, the shear strength is determined by means of the crack sliding...

  4. Shear strength of non-shear reinforced concrete elements

    DEFF Research Database (Denmark)

    Hoang, Cao linh

    1997-01-01

    The report deals with the shear strength of statically indeterminate reinforced concrete beams without shear reinforcement. Solutions for a number of beams with different load and support conditions have been derived by means of the crack sliding model developed by Jin- Ping Zhang.This model...

  5. A streamwise constant model of turbulence in plane Couette flow

    OpenAIRE

    Gayme, D. F.; McKeon, B. J.; Papachristodoulou, A.; Bamieh, B; Doyle, J. C.

    2010-01-01

    Streamwise and quasi-streamwise elongated structures have been shown to play a significant role in turbulent shear flows. We model the mean behaviour of fully turbulent plane Couette flow using a streamwise constant projection of the Navier–Stokes equations. This results in a two-dimensional three-velocity-component (2D/3C) model. We first use a steady-state version of the model to demonstrate that its nonlinear coupling provides the mathematical mechanism that shapes the turbulent velocity p...

  6. Size-effects in plane strain sheet-necking

    DEFF Research Database (Denmark)

    Niordson, Christian Frithiof; Redanz, Pia

    2003-01-01

    are analyzed. The strain gradient plasticity theory predicts delayed onset of localization when compared to conventional theory, and it depresses deformation localization in the neck. The sensitivity to imperfections is analyzed as well as differently hardening materials.......A finite strain generalization of the strain gradient plasticity theory by Fleck and Hutchinson (2001) is proposed and used to study size effects in plane strain necking of thin sheets using the finite element method. Both sheets with rigid grips at the ends and specimens with shear free ends...

  7. Size-effects in plane strain sheet-necking

    DEFF Research Database (Denmark)

    Niordson, Christian Frithiof; Redanz, Pia

    2004-01-01

    and specimens with shear free ends are analyzed. The strain gradient plasticity theory predicts delayed onset of localization when compared to conventional theory, and it depresses deformation localization in the neck. The sensitivity to imperfections is analyzed as well as differently hardening materials. (C......A finite strain generalization of the strain gradient plasticity theory by Fleck and Hutchinson (J. Mech. Phys. Solids 49 (2001a) 2245) is proposed and used to study size effects in plane strain necking of thin sheets using the finite element method. Both sheets with rigid grips at the ends...

  8. Numerical Modelling of Double-Steel Plate Composite Shear Walls

    Directory of Open Access Journals (Sweden)

    Michaela Elmatzoglou

    2017-02-01

    Full Text Available Double-steel plate concrete composite shear walls are being used for nuclear plants and high-rise buildings. They consist of thick concrete walls, exterior steel faceplates serving as reinforcement and shear connectors, which guarantee the composite action between the two different materials. Several researchers have used the Finite Element Method to investigate the behaviour of double-steel plate concrete walls. The majority of them model every element explicitly leading to a rather time-consuming solution, which cannot be easily used for design purposes. In the present paper, the main objective is the introduction of a three-dimensional finite element model, which can efficiently predict the overall performance of a double-steel plate concrete wall in terms of accuracy and time saving. At first, empirical formulations and design relations established in current design codes for shear connectors are evaluated. Then, a simplified finite element model is used to investigate the nonlinear response of composite walls. The developed model is validated using results from tests reported in the literature in terms of axial compression and monotonic, cyclic in-plane shear loading. Several finite element modelling issues related to potential convergence problems, loading strategies and computer efficiency are also discussed. The accuracy and simplicity of the proposed model make it suitable for further numerical studies on the shear connection behaviour at the steel-concrete interface.

  9. Shear wave speed recovery in sonoelastography using crawling wave data.

    Science.gov (United States)

    Lin, Kui; McLaughlin, Joyce; Renzi, Daniel; Thomas, Ashley

    2010-07-01

    The crawling wave experiment, in which two harmonic sources oscillate at different but nearby frequencies, is a development in sonoelastography that allows real-time imaging of propagating shear wave interference patterns. Previously the crawling wave speed was recovered and used as an indicator of shear stiffness; however, it is shown in this paper that the crawling wave speed image can have artifacts that do not represent a change in stiffness. In this paper, the locations and shapes of some of the artifacts are exhibited. In addition, a differential equation is established that enables imaging of the shear wave speed, which is a quantity strongly correlated with shear stiffness change. The full algorithm is as follows: (1) extract the crawling wave phase from the spectral variance data; (2) calculate the crawling wave phase wave speed; (3) solve a first-order PDE for the phase of the wave emanating from one of the sources; and (4) compute and image the shear wave speed on a grid in the image plane.

  10. Shear correction factors for layered plates and shells

    Science.gov (United States)

    Gruttmann, F.; Wagner, W.

    2016-10-01

    In this paper layered composite shells subjected to static loading are considered. The theory is based on a multi-field functional, where the associated Euler-Lagrange equations include besides the global shell equations formulated in stress resultants, the local in-plane equilibrium in terms of stresses and a constraint which enforces the correct shape of warping through the thickness. Within representative volume elements warping displacements are interpolated with layerwise cubic functions in thickness direction and constant shape throughout the reference surface. Elimination of warping and Lagrange parameters by static condensation leads to a material matrix for the stress resultants and to shear correction factors for layered plates and shells. For linear elasticity the computation can be done once in advance. The condensed material matrix is used in displacement based elements along with the enhanced strain method or in mixed hybrid elements with the usual 5 or 6 nodal degrees of freedom. This allows standard geometrical boundary conditions and the elements are applicable also to shell intersection problems. The interlaminar shear stresses are evaluated via the constitutive law by back substitution of the eliminated parameters. The computed transverse shear stresses are automatically continuous at the layer boundaries and zero at the outer surfaces. Furthermore, the integrals of the shear stresses coincide exactly with the shear forces without introduction of further constraints.

  11. Shear correction factors for layered plates and shells

    Science.gov (United States)

    Gruttmann, F.; Wagner, W.

    2017-01-01

    In this paper layered composite shells subjected to static loading are considered. The theory is based on a multi-field functional, where the associated Euler-Lagrange equations include besides the global shell equations formulated in stress resultants, the local in-plane equilibrium in terms of stresses and a constraint which enforces the correct shape of warping through the thickness. Within representative volume elements warping displacements are interpolated with layerwise cubic functions in thickness direction and constant shape throughout the reference surface. Elimination of warping and Lagrange parameters by static condensation leads to a material matrix for the stress resultants and to shear correction factors for layered plates and shells. For linear elasticity the computation can be done once in advance. The condensed material matrix is used in displacement based elements along with the enhanced strain method or in mixed hybrid elements with the usual 5 or 6 nodal degrees of freedom. This allows standard geometrical boundary conditions and the elements are applicable also to shell intersection problems. The interlaminar shear stresses are evaluated via the constitutive law by back substitution of the eliminated parameters. The computed transverse shear stresses are automatically continuous at the layer boundaries and zero at the outer surfaces. Furthermore, the integrals of the shear stresses coincide exactly with the shear forces without introduction of further constraints.

  12. Emergence of stochastic dynamics in plane Couette flow

    CERN Document Server

    Gvalani, Rishabh

    2016-01-01

    Spatially localized states play an important role in transition to turbulence in shear flows (Kawahara, Uhlmann & van Veen, Annu. Rev. Fluid Mech. 44, 203 (2012)). Despite the fact that some of them are attractors on the separatrix between laminar and turbulent flows, little is known of their dynamics. We investigate here the temporal dynamics of such steady spatially localized solutions in the context of plane Couette flow. These solutions exist on oscillating branches in parameter space. We consider the saddle-nodes of these branches as initial conditions of simulations run with offset Reynolds numbers. We observe a relaminarization regime mostly characterized by deterministic dynamics and identify within this regime the existence of parameter intervals in which the results are stochastic and long-lived chaotic transients are observed. These results are obtained below the threshold for transition, shed light on the emergence of stochasticity in transitional plane Couette flow and will likely inform a ra...

  13. Real-time optical image subtraction by a holographic shear lens

    Science.gov (United States)

    Rao, V. Venkateswara; Joenathan, C.; Sirohi, R. S.

    1985-08-01

    A new optical method of image subtraction by employing a holographic shear lens is proposed. The principle underlying this technique is that of optical interference between two sheared fields produced by the holographic shear lens (HSL). Two dissimilar inputs with some common characters are subtracted in real time while keeping the HSL at the Fourier plane of a well corrected lens. The difference is detectable only when zero fringe is obtained in the interferogram. Experimental verification is presented with the results. The basic advantages of this technique are the simplicity in aligning the input transparencies and the real time operation.

  14. A New Multiaxial High-Cycle Fatigue Criterion Based on the Critical Plane for Ductile and Brittle Materials

    Science.gov (United States)

    Wang, Cong; Shang, De-Guang; Wang, Xiao-Wei

    2015-02-01

    An improved high-cycle multiaxial fatigue criterion based on the critical plane was proposed in this paper. The critical plane was defined as the plane of maximum shear stress (MSS) in the proposed multiaxial fatigue criterion, which is different from the traditional critical plane based on the MSS amplitude. The proposed criterion was extended as a fatigue life prediction model that can be applicable for ductile and brittle materials. The fatigue life prediction model based on the proposed high-cycle multiaxial fatigue criterion was validated with experimental results obtained from the test of 7075-T651 aluminum alloy and some references.

  15. Electroosmotic shear flow in microchannels

    NARCIS (Netherlands)

    Mampallil, Dileep; Ende, van den Dirk

    2013-01-01

    We generate and study electroosmotic shear flow in microchannels. By chemically or electrically modifying the surface potential of the channel walls a shear flow component with controllable velocity gradient can be added to the electroosmotic flow caused by double layer effects at the channel walls.

  16. A NEW APPROACH TO THE NONLINEAR STABILITY OF PARALLEL SHEAR FLOWS

    Institute of Scientific and Technical Information of China (English)

    XU Lan-xi; HUANG Yong-nian

    2005-01-01

    Lyapunov's second method was used to study the nonlinear stability of parallel shear flows for stress-free boundaries. By introducing an energy functional, it was shown that the plane Couette and plane Poiseuille flows are conditionally and asymptotically stable for all Reynolds numbers. In particular, to two-dimensional perturbations, by defining new energy functionals the unconditional stability of the basic flows was proved.

  17. Strength of precast concrete shear joints reinforced with high-strength wire ropes

    DEFF Research Database (Denmark)

    Joergensen, Henrik B.; Hoang, Linh Cao; Hagsten, Lars German

    2017-01-01

    This paper concerns the in-plane shear strength of connections between precast concrete wall elements reinforced with looped high-strength wire ropes. The looped wire ropes are pre-installed in so-called ‘wire boxes’ which function as shear keys. Although only a small amount of research...... on the shear strength of such connections can be found in the literature, this type of connection is increasingly being used because wire ropes are much more construction-friendly than traditional U-bars. A rigid plastic upper bound model for the shear strength of wall connections reinforced with looped wire...... ropes that are pre-installed in wire boxes is presented along with test results on the shear strength of connections with double-wire boxes. It is shown that the plastic solution agrees well with both the obtained test results and results from previously conducted tests....

  18. Study of Strength of RC Shear Wall at Different Location on Multi-Storied Residential Building

    Directory of Open Access Journals (Sweden)

    Syed Ehtesham Ali

    2014-09-01

    Full Text Available Shear wall systems are one of the most commonly used lateral load resisting systems in high-rise buildings. Shear walls have very high in plane stiffness and strength, which can be used to simultaneously resist large horizontal loads and support gravity loads, making them quite advantageous in many structural engineering applications. There are lots of literatures available to design and analyze the shear wall. However, the decision about the location of shear wall in multi-storey building is not much discussed in any literatures. In this paper, therefore, main focus is to determine the solution for shear wall location in multi-storey building. A RCC building of six storey placed in HYDERABAD subjected to earthquake loading in zone-II is considered. An earthquake load is calculated by seismic coefficient method using IS 1893 (PART–I:2002. These analyses were performed using ETABS.

  19. Evaluation of interlaminar shear strength of a unidirectional carbon/epoxy laminated composite under impact loading

    Science.gov (United States)

    Yokoyama, T.; Nakai, K.

    2006-08-01

    The interlaminar shear strength (ILSS) of a unidirectional carbon/epoxy (T700/2521) laminated composite under impact loading is determined using the conventional split Hopkinson pressure bar. Double-notch shear (DNS) specimens with lateral constraint from a supporting jig are used in the static and impact interlaminar compressive shear tests. Short-beam shear specimens are also used under static 3-point bending. Numerical stress analyses are performed to determine the shear stress and normal stress distributions on the expected failure plane in the DNS specimen using the MSC/NASTRAN package. The effect of deformation rate on the ILSS and failure mode is investigated. It is observed that the ILSS is independent of the deformation rate up to nearly 1.5m/s (dotγ ≈ 780/s). The validity of the test results is confirmed by microscopic examinations of both static and impact failure surfaces for the DNS specimens.

  20. A Piezoelectric Shear Stress Sensor

    Science.gov (United States)

    Kim, Taeyang; Saini, Aditya; Kim, Jinwook; Gopalarathnam, Ashok; Zhu, Yong; Palmieri, Frank L.; Wohl, Christopher J.; Jiang, Xiaoning

    2016-01-01

    In this paper, a piezoelectric sensor with a floating element was developed for shear stress measurement. The piezoelectric sensor was designed to detect the pure shear stress suppressing effects of normal stress generated from the vortex lift-up by applying opposite poling vectors to the: piezoelectric elements. The sensor was first calibrated in the lab by applying shear forces and it showed high sensitivity to shear stress (=91.3 +/- 2.1 pC/Pa) due to the high piezoelectric coefficients of PMN-33%PT (d31=-1330 pC/N). The sensor also showed almost no sensitivity to normal stress (less than 1.2 pC/Pa) because of the electromechanical symmetry of the device. The usable frequency range of the sensor is 0-800 Hz. Keywords: Piezoelectric sensor, shear stress, floating element, electromechanical symmetry

  1. Shear jamming in highly strained granular system without shear banding

    Science.gov (United States)

    Zhao, Yiqiu; Barés, Jonathan; Zheng, Hu; Behringer, Robert

    2016-11-01

    Bi et al. have shown that, if sheared, a granular material can jam even if its packing fraction (ϕ) is lower than the critical isotropic jamming point ϕJ. They have introduced a new critical packing fraction value ϕS such that for ϕSjams if sheared. Nevertheless, the value of ϕS as a function of the shear profile or the strain necessary to observe jamming remain poorly understood because of the experimental complexity to access high strain without shear band. We present a novel 2D periodic shear apparatus made of 21 independent, aligned and mirrored glass rings. Each ring can be moved independently which permits us to impose any desired shear profile. The circular geometry allows access to any strain value. The forces between grains are measured using reflective photoelasticity. By performing different shear profiles for different packing fractions we explored the details of jamming diagram including the location of the yield surface. This work is supported by NSF No.DMR1206351, NASA No.NNX15AD38G and W. M. Keck Foundation.

  2. A Very Large Eddy Simulation of the Nonreacting Flow in a Single-Element Lean Direct Injection Combustor Using PRNS with a Nonlinear Subscale Model

    Science.gov (United States)

    Shih, Tsan-Hsing; Liu, Nan-Suey

    2009-01-01

    Very large eddy simulation (VLES) of the nonreacting turbulent flow in a single-element lean direct injection (LDI) combustor has been successfully performed via the approach known as the partially resolved numerical simulation (PRNS/VLES) using a nonlinear subscale model. The grid is the same as the one used in a previous RANS simulation, which was considered as too coarse for a traditional LES simulation. In this study, we first carry out a steady RANS simulation to provide the initial flow field for the subsequent PRNS/VLES simulation. We have also carried out an unsteady RANS (URANS) simulation for the purpose of comparing its results with that of the PRNS/VLES simulation. In addition, these calculated results are compared with the experimental data. The present effort has demonstrated that the PRNS/VLES approach, while using a RANS type of grid, is able to reveal the dynamically important, unsteady large-scale turbulent structures occurring in the flow field of a single-element LDI combustor. The interactions of these coherent structures play a critical role in the dispersion of the fuel, hence, the mixing between the fuel and the oxidizer in a combustor.

  3. The experimental basis for interpreting particle and magnetic fabrics of sheared till

    Science.gov (United States)

    Iverson, N.R.; Hooyer, T.S.; Thomason, J.F.; Graesch, M.; Shumway, J.R.

    2008-01-01

    Particle fabrics of basal tills may allow testing of the bed-deformation model of glacier flow, which requires high bed shear strains (>100). Field studies, however, have not yielded a systematic relationship between shear-strain magnitude and fabric development. To isolate this relationship four basal tills and viscous putty were sheared in a ring-shear device to strains as high as 714. Fabric was characterized within a zone of shear deformation using the long-axis orientations of fine-gravel and sand particles and the anisotropy of magnetic susceptibility (AMS) of small (???5-8 cm3) intact samples. Results indicate that till particles rotate toward the plane of shearing with long-axis orientations that become tightly clustered in the direction of shear (0??78 particle-size fraction under consideration. These results do not support the Jeffery model of particle rotation, which correctly describes particle rotation in the viscous putty but not in the tills, owing to fluid-mechanical assumptions of the model that are violated in till. The sensitivity of fabric development to shear-strain magnitude indicates that, for most till units where shear-strain magnitude is poorly known, attributing fabric variations to spatial differences in other variables, such as till thickness or water content, will be inherently speculative. Attributing fabric characteristics to particular basal till facies is uncertain because shear-strain magnitude is unlikely to be closely correlated to till facies. Weak or spatially variable fabrics, in the absence of post-depositional disturbance or major deviations from unidirectional simple shear, indicate that till has not been pervasively sheared to the high strains required by the bed-deformation model. Strong flow-parallel fabrics are a necessary but insufficient criterion for confirming the model. Copyright ?? 2008 John Wiley & Sons, Ltd.

  4. Shear Profiles and Velocity Distribution in Dense Shear Granular Flow

    Institute of Scientific and Technical Information of China (English)

    WANG Deng-Ming; ZHOU You-He

    2009-01-01

    We perform DEM simulations to investigate the influence of the packing fraction γ on the,shape of mean tan-gential velocity profile in a 2D annular dense shear granular flow. There is a critical packing fraction γc. For γ < γc, the mean tangential velocity profile shows a roughly exponential decay from the shearing boundary and is almost invariant to the imposed shear rate. However, for γ γc, the tangential velocity profile exhibits a rate-dependence feature and changes from linear to nonlinear gradually with the increasing shear rate. Fhrther-more, the distributions of normalized tangential velocities at different positions along radial direction exhibit the Gaussian or the composite Gaussian distributing features.

  5. Tensile/Shear Behaviour of Multi-stitched/Nano Composites

    Science.gov (United States)

    Bilisik, Kadir; Kaya, Gaye

    2017-02-01

    This study aims to investigate tensile/shear behavior of multi-stitched/nano composites. For this purpose, non-stitched, non-stitched/nano, multi-stitched and multi-stitched/nano composites were made. It was shown that the warp/filling tensile strength and modulus of composites were slightly reduced in both multi-stitched and multi-stitched/nano composites due to fiber breakage that resulted from the multi-stitching process. In addition, there were not significant differences between non-stitched and multi-stitched structures. The non-stitched/nano composite showed slightly higher in-plane shear strength compared with the non-stitched composite. The in-plane shear strength of the non-stitched composite, on the other hand, increased steadily compared to the multi-stitched composite because of the stitching process and the interface between the stitching yarn and polymer matrix. Stitching significantly improved the delamination resistance in the multi-stitched and multi-stitched/nano composites experienced a small amount of damaged areas. The incorporation of nano silica improved the damage resistance of multi-stitched composites. Therefore, the damaged tolerance composite was developed with stitching and the addition of the nano silica for various industrial applications, such as electronic boards.

  6. Structural analysis of red blood cell aggregates under shear flow.

    Science.gov (United States)

    Chesnutt, J K W; Marshall, J S

    2010-03-01

    A set of measures of red blood cell (RBC) aggregates are developed and applied to examine the aggregate structure under plane shear and channel flows. Some of these measures are based on averages over the set of red blood cells which are in contact with each other at a given time. Other measures are developed by first fitting an ellipse to the planar projection of the aggregate, and then examining the area and aspect ratio of the fit ellipse as well as the orientations of constituent RBCs with respect to the fit ellipse axes. The aggregate structural measures are illustrated using a new mesoscale computational model for blood cell transport, collision and adhesion. The sensitivity of this model to change in adhesive surface energy density and shear rate on the aggregate structure is examined. It is found that the mesoscale model predictions exhibit reasonable agreement with experimental and theoretical data for blood flow in plane shear and channel flows. The new structural measures are used to examine the differences between predictions of two- and three-dimensional computations of the aggregate formation, showing that two-dimensional computations retain some of the important aspects of three-dimensional computations.

  7. Geometry of state space in plane Couette flow

    Science.gov (United States)

    Cvitanović, P.; Gibson, J. F.

    A large conceptual gap separates the theory of low-dimensional chaotic dynamics from the infinite-dimensional nonlinear dynamics of turbulence. Recent advances in experimental imaging, computational methods, and dynamical systems theory suggest a way to bridge this gap in our understanding of turbulence. Recent discoveries show that recurrent coherent structures observed in wall-bounded shear flows (such as pipes and plane Couette flow) result from close passes to weakly unstable invariant solutions of the Navier-Stokes equations. These 3D, fully nonlinear solutions (equilibria, traveling waves, and periodic orbits) structure the state space of turbulent flows and provide a skeleton for analyzing their dynamics. We calculate a hierarchy of invariant solutions for plane Couette, a canonical wall-bounded shear flow. These solutions reveal organization in the flow's turbulent dynamics and can be used to predict directly from the fundamental equations physical quantities such as bulk flow rate and mean wall drag. All results and the code that generates them are disseminated through through our group's open-source CFD software and solution database Channelflow.org and the collaborative e-book ChaosBook.org.

  8. Fifty years of shear zones

    Science.gov (United States)

    Graham, Rodney

    2017-04-01

    We are here, of course, because 1967 saw the publication of John Ramsay's famous book. Two years later a memorable field trip from Imperial College to the Outer Hebrides saw John on a bleak headland on the coast of North Uist where a relatively undeformed metadolerite within Lewisian (Precambrian) gneisses contained ductile shear zones with metamorphic fabrics in amphibolite facies. One particular outcrop was very special - a shear zone cutting otherwise completely isotropic, undeformed metadolerite, with an incremental foliation starting to develop at 45° to the deformation zone, and increasing in intensity as it approached the shear direction. Here was proof of the process of simple shear under ductile metamorphic conditions - the principles of simple shear outlined in John Ramsay's 1967 book clearly visible in nature, and verified by Ramsay's mathematical proofs in the eventual paper (Ramsay and Graham, 1970). Later work on the Lewisian on the mainland of Scotland, in South Harris, in Africa, and elsewhere applied Ramsay's simple shear principles more liberally, more imprecisely and on larger scale than at Caisteal Odair, but in retrospect it documented what seems now to be the generality of mid and lower crustal deformation. Deep seismic reflection data show us that on passive margins hyper-stretched continental crust (whether or not cloaked by Seaward Dipping Reflectors) seems to have collapsed onto the mantle. Crustal faults mostly sole out at or above the mantle - so the Moho is a detachment- an 'outer marginal detachment', if you like, and, of course, it must be a ductile shear. On non-volcanic margins this shear zone forms the first formed ocean floor before true sea floor spreading gets going to create real oceanic crust. Gianreto Manatschal, Marcel Lemoine and others realised that the serpentinites described in parts of the Alps are exposed remnants of this ductile shear zone. Associated ophicalcite breccias tell of sea floor exposure, while high

  9. Arnold's Projective Plane and -Matrices

    Directory of Open Access Journals (Sweden)

    K. Uchino

    2010-01-01

    Full Text Available We will explain Arnold's 2-dimensional (shortly, 2D projective geometry (Arnold, 2005 by means of lattice theory. It will be shown that the projection of the set of nontrivial triangular -matrices is the pencil of tangent lines of a quadratic curve on Arnold's projective plane.

  10. Affine Contractions on the Plane

    Science.gov (United States)

    Celik, D.; Ozdemir, Y.; Ureyen, M.

    2007-01-01

    Contractions play a considerable role in the theory of fractals. However, it is not easy to find contractions which are not similitudes. In this study, it is shown by counter examples that an affine transformation of the plane carrying a given triangle onto another triangle may not be a contraction even if it contracts edges, heights or medians.…

  11. Distributed storage in the plane

    NARCIS (Netherlands)

    Altman, Eitan; Avrachenkov, Konstatin; Goseling, Jasper

    2013-01-01

    We consider storage devices located in the plane according to a general point process and specialize the results for the homogeneous Poisson process. A large data file is stored at the storage devices, which have limited storage capabilities. Hence, they can only store parts of the data. Clients can

  12. Distributed storage in the plane

    NARCIS (Netherlands)

    Altman, Eitan; Avrachenkov, Konstatin; Goseling, Jasper

    2014-01-01

    We consider storage devices located in the plane according to a general point process and specialize the results for the homogeneous Poisson process. A large data file is stored at the storage devices, which have limited storage capabilities. Hence, they can only store parts of the data. Clients can

  13. Plane and parabolic solar panels

    CERN Document Server

    Sales, J H O

    2009-01-01

    We present a plane and parabolic collector that absorbs radiant energy and transforms it in heat. Therefore we have a panel to heat water. We study how to increment this capture of solar beams onto the panel in order to increase its efficiency in heating water.

  14. Distributed storage in the plane

    NARCIS (Netherlands)

    Altman, Eitan; Avrachenkov, Konstatin; Goseling, Jasper

    2013-01-01

    We consider storage devices located in the plane according to a general point process and specialize the results for the homogeneous Poisson process. A large data file is stored at the storage devices, which have limited storage capabilities. Hence, they can only store parts of the data. Clients can

  15. Distributed storage in the plane

    NARCIS (Netherlands)

    Altman, Eitan; Avrachenkov, Konstatin; Goseling, Jasper

    2014-01-01

    We consider storage devices located in the plane according to a general point process and specialize the results for the homogeneous Poisson process. A large data file is stored at the storage devices, which have limited storage capabilities. Hence, they can only store parts of the data. Clients can

  16. Gravitational Couplings for y-Gop-Planes

    CERN Document Server

    Ospina-Giraldo, J F

    2000-01-01

    The Wess-Zumino action for y deformed and generalized orientifold planes (yGOp-planes) is presented and one power expantion is realized from which processes that involves yGOp-planes, RR-forms, gravitons and gaugeons, are obtained. Finally non-standard yGOp-planes are showed.

  17. ANALYSIS OF PULSATILE FLOW IN THE PARALLEL-PLATE FLOW CHAMBER WITH SPATIAL SHEAR STRESS GRADIENT

    Institute of Scientific and Technical Information of China (English)

    QIN Kai-rong; HU Xu-qu; LIU Zhao-rong

    2007-01-01

    The Parallel-Plate Flow Chamber (PPFC), of which the height is far smaller than its own length and width, is one of the main apparatus for the in-vitro study of the mechanical behavior of cultured vascular Endothelical Cells (ECs) exposed to fluid shear stress. The steady flow in different kinds of PPFC has been extensively investigated, whereas, the pulsatile flow in the PPFC has little attention. In consideration of the characteristics of geometrical size and pulsatile flow in the PPFC, the 3-D pulsatile flow was decomposed into a 2-D pulsatile flow in the vertical plane, and an incompressible plane potential flow in the horizontal plane. A simple method was then proposed to analyze the pulsatile flow in the PPFC with spatial shear stress gradient. On the basis of the method, the pulsatile fluid shear stresses in several reported PPFCs with spatial shear stress gradients were calculated. The results were theoretically meaningful for applying the PPFCs in-vitro, to simulate the pulsatile fluid shear stress environment, to which cultured ECs were exposed.

  18. Linear Instability of the Plane Couette and Plane Poiseuille Flows

    CERN Document Server

    Chefranov, Sergey G

    2015-01-01

    We show possibility of the Plane Couette (PC) flow instability for Reynolds number Re>Reth=140. This new result of the linear hydrodynamic stability theory is obtained on the base of refusal from the traditionally used assumption on longitudinal periodicity of the disturbances along the direction of the fluid flow. We found that earlier existing understanding on the linear stability of this flow for any arbitrary large Reynolds number is directly related with an assumption on the separation of the variables of the spatial variability for the disturbance field and their periodicity in linear theory of stability. By the refusal from the pointed assumptions also for the Plane Poiseuille (PP) flow, we get a new threshold Reynolds value Reth=1040 that with 4% accuracy agrees with the experiment contrary to more than 500% discrepancy for the earlier known estimate Reth=5772 obtained in the frame of the linear theory but when using the "normal" disturbance form (S. A. Orszag, 1971).

  19. Hydrodynamic Interactions between Two Equally Sized Spheres in Viscoelastic Fluids in Shear Flow

    NARCIS (Netherlands)

    Snijkers, F.; Pasquino, R.; Vermant, J.

    2013-01-01

    The effect of using a viscoelastic suspending medium, on the;in-plane hydrodynamic interaction between two equally sized spheres in shear flow is studied experimentally to understand flow-induced assembly behavior (i.e., string formation). A counterrotating device equipped with a Couette geometry is

  20. Thermal Expansion of Self-Organized and Shear-Oriented Cellulose Nanocrystal Films

    Science.gov (United States)

    Jairo A. Diaz; Xiawa Wu; Ashlie Martini; Jeffrey P. Youngblood; Robert J. Moon

    2013-01-01

    The coefficient of thermal expansion (CTE) of cellulose nanocrystal (CNC) films was characterized using novel experimental techniques complemented by molecular simulations. The characteristic birefringence exhibited by CNC films was utilized to calculate the in-plane CTE of selforganized and shear-oriented self-standing CNC films from room temperature to 100 °...

  1. Grafted polymer under shear flow

    Science.gov (United States)

    Kumar, Sanjiv; Foster, Damien P.; Giri, Debaprasad; Kumar, Sanjay

    2016-04-01

    A self-attracting-self-avoiding walk model of polymer chain on a square lattice has been used to gain an insight into the behaviour of a polymer chain under shear flow in a slit of width L. Using exact enumeration technique, we show that at high temperature, the polymer acquires the extended state continuously increasing with shear stress. However, at low temperature the polymer exhibits two transitions: a transition from the coiled to the globule state and a transition to a stem-flower like state. For a chain of finite length, we obtained the exact monomer density distributions across the layers at different temperatures. The change in density profile with shear stress suggests that the polymer under shear flow can be used as a molecular gate with potential application as a sensor.

  2. SEDflume - High Shear Stress Flume

    Data.gov (United States)

    Federal Laboratory Consortium — The U.S. Army Corps of Engineers High Shear Stress flume (SEDflume) is designed for estimating erosion rates of fine-grained and mixed fine/coarse grained sediments...

  3. Gene Transfer of Tumor-Reactive TCR Confers Both High Avidity and Tumor Reactivity to Nonreactive Peripheral Blood Mononuclear Cells and Tumor-Infiltrating Lymphocytes1

    Science.gov (United States)

    Johnson, Laura A.; Heemskerk, Bianca; Powell, Daniel J.; Cohen, Cyrille J.; Morgan, Richard A.; Dudley, Mark E.; Robbins, Paul F.; Rosenberg, Steven A.

    2007-01-01

    Cell-based antitumor immunity is driven by CD8+ cytotoxic T cells bearing TCR that recognize specific tumor-associated peptides bound to class I MHC molecules. Of several cellular proteins involved in T cell:target-cell interaction, the TCR determines specificity of binding; however, the relative amount of its contribution to cellular avidity remains unknown. To study the relationship between TCR affinity and cellular avidity, with the intent of identifying optimal TCR for gene therapy, we derived 24 MART-1:27–35 (MART-1) melanoma Ag-reactive tumor-infiltrating lymphocyte (TIL) clones from the tumors of five patients. These MART-1-reactive clones displayed a wide variety of cellular avidities. α and β TCR genes were isolated from these clones, and TCR RNA was electroporated into the same non-MART-1-reactive allogeneic donor PBMC and TIL. TCR recipient cells gained the ability to recognize both MART-1 peptide and MART-1-expressing tumors in vitro, with avidities that closely corresponded to the original TCR clones (p = 0.018–0.0003). Clone DMF5, from a TIL infusion that mediated tumor regression clinically, showed the highest avidity against MART-1 expressing tumors in vitro, both endogenously in the TIL clone, and after RNA electroporation into donor T cells. Thus, we demonstrated that the TCR appeared to be the core determinant of MART-1 Ag-specific cellular avidity in these activated T cells and that nonreactive PBMC or TIL could be made tumor-reactive with a specific and predetermined avidity. We propose that inducing expression of this highly avid TCR in patient PBMC has the potential to induce tumor regression, as an “off-the-shelf” reagent for allogeneic melanoma patient gene therapy. PMID:17056587

  4. Effects of induced shear deformation on microstructure and texture evolution in CP-Ti rolled sheets

    Energy Technology Data Exchange (ETDEWEB)

    Milner, Justin L. [Department of Automotive Engineering, Clemson University, Greenville, SC 29607 (United States); Abu-Farha, Fadi, E-mail: FADI@clemson.edu [Department of Automotive Engineering, Clemson University, Greenville, SC 29607 (United States); Kurfess, Thomas [School of Mechanical Engineering, Georgia Institute of Technology, GA 30332 (United States); Hammond, Vincent H. [US Army Research Laboratory, Aberdeen Proving Ground, MD 21005 (United States)

    2014-12-01

    Commercial pure titanium sheets were deformed by shear rolling at 400 °C with subsequent annealing to investigate microstructure and texture evolution along with its effects on the mechanical properties. A four sheet multilayer rolling scheme was used to isolate shear strains within the outer sheets, termed isolated shear rolling (ISR), thus allowing for direct comparison between shear strained material (outer sheets) and plane-strained material under similar conditions. Microstructure and texture evolution were investigated by electron backscatter diffraction analysis, while mechanical properties were evaluated through tensile testing aided by digital image correlation (DIC). Texture was seen to evolve from a ±30° transverse direction (TD) split basal texture to primarily basal texture (〈0001〉//Normal Direction) for the shear-strained sheets, in comparison with a slight rotation to a ±20° TD-split for the plane-strained sheets. After short-term annealing at 600 °C for 15 min, texture remained similar to that of the as-processed material yet at lower intensity levels. Compared to the base material, shear-rolled material showed much higher Lankford Coefficient values, with a significant boost attributed to shear deformation. The greater stretch formability is achieved in the shear-rolled material by rotation of the basal poles to become parallel to the sheet thickness. The results obtained here with ISR in regards to the effects of inducing higher shear strains on the rolled material are comparable to those reported in the literature by differential speed rolling (DSR)

  5. Load carrying capacity of shear wall t-connections reinforced with high strength wire ropes

    DEFF Research Database (Denmark)

    Jørgensen, Henrik B.; Bryndom, Thor; Larsen, Michael

    2016-01-01

    Traditionally, U-bar loop connections with keyed joints have been used in vertical shear connections between precast concrete wall elements. However, in the recent years, connections with looped high strength wire ropes instead of U-bar loops have proven to be a much more construction......-friendly solution. The wire ropes have no bending stiffness and therefore allow for an easier vertical installation of the wall elements. During the last 10 – 15 years, a number of shear tests on plane wire rope connections have been carried out. However, to the best knowledge of the authors, tests on wire rope...... connections for assembly of precast elements in different planes, such as T- and L-connections, have not yet been published. This paper presents the results of a large test series recently conducted at the University of Southern Denmark to study the shear behaviour of high strength wire rope T...

  6. Load Carrying Capacity of Shear Wall T-Connections Reinforced with High Strength Wire Ropes

    DEFF Research Database (Denmark)

    Jørgensen, Henrik Brøner; Bryndum, Thor; Larsen, Michael

    2017-01-01

    Traditionally, U-bar loop connections with keyed joints have been used in vertical shear connections between precast concrete wall elements. However, in the recent years, connections with looped high strength wire ropes instead of U-bar loops have proven to be a much more construction......-friendly solution. The wire ropes have no bending stiffness and therefore allow for an easier vertical installation of the wall elements. During the last 10 – 15 years, a number of shear tests on plane wire rope connections have been carried out. However, to the best knowledge of the authors, tests on wire rope...... connections for assembly of precast elements in different planes, such as T- and L-connections, have not yet been published. This paper presents the results of a large test series recently conducted at the University of Southern Denmark to study the shear behaviour of high strength wire rope T...

  7. Surface-mounted bender elements for measuring horizontal shear wave velocity of soils

    Institute of Scientific and Technical Information of China (English)

    Yan-guo ZHOU; Yun-min CHEN; Yoshiharu ASAKA; Tohru ABE

    2008-01-01

    The bender element testing features its in-plane directivity,which allows using bender elements to measure the shear wave velocities in a wider range of in-plane configurations besides the standard tip-to-tip alignment.This paper proposed a novel bender element testing technique for measuring the horizontal shear wave velocity of soils,where the bender elements are surface-mounted and the axes of the source and receiver elements are parallel to each other.The preliminary tests performed on model ground of silica sand showed that,by properly determining the travel distance and time of the shear waves,the surface-mounted bender elements can perform as accurately as the conventional "tip-to-tip" configuration.Potentially,the present system provides a promising nondestructive tool for characterizing geomaterials and site conditions both in laboratory and in the fields.

  8. Evaluation of Transverse Thermal Stresses in Composite Plates Based on First-Order Shear Deformation Theory

    Science.gov (United States)

    Rolfes, R.; Noor, A. K.; Sparr, H.

    1998-01-01

    A postprocessing procedure is presented for the evaluation of the transverse thermal stresses in laminated plates. The analytical formulation is based on the first-order shear deformation theory and the plate is discretized by using a single-field displacement finite element model. The procedure is based on neglecting the derivatives of the in-plane forces and the twisting moments, as well as the mixed derivatives of the bending moments, with respect to the in-plane coordinates. The calculated transverse shear stiffnesses reflect the actual stacking sequence of the composite plate. The distributions of the transverse stresses through-the-thickness are evaluated by using only the transverse shear forces and the thermal effects resulting from the finite element analysis. The procedure is implemented into a postprocessing routine which can be easily incorporated into existing commercial finite element codes. Numerical results are presented for four- and ten-layer cross-ply laminates subjected to mechanical and thermal loads.

  9. Shear induced diffusion in a red blood cell suspension

    Science.gov (United States)

    Podgorski, Thomas; Grandchamp, Xavier; Srivastav, Aparna; Coupier, Gwennou

    2012-11-01

    In the microcirculation, blood exhibits an inhomogeneous structure which results in the well know Fahraeus-Lindqvist effect : the apparent viscosity decreases when the diameter of the capillary decreases due to the formation of a marginal cell depletion layer (known as plasma skimming). This structure is a consequence of several phenomena, which include i) the migration of cells aways from walls due to lift forces and gradients of shear and ii) shear induced diffusion due to collisions and interactions among cells. We investigated these phenomena through experiments in simple shear and microchannel flows, with dilute suspensions of vesicles and blood cells. Pairwise interactions between suspended objects result in non-linear and flow-dependent diffusion, whose properties have been measured in different experiments for vesicles and blood cells. The injection of a sheet of concentrated blood cell suspension in a microchannel with a rectangular cross-section allows, through the measurement of its widening along the channel, to measure the diffusivity of blood cells, both in the local plane of shear and in the vorticity direction.

  10. Vortex dynamics and shear layer instability in high intensity cyclotrons

    CERN Document Server

    Cerfon, Antoine J

    2016-01-01

    We show that the space charge dynamics of high intensity beams in the plane perpendicular to the magnetic field in cyclotrons is described by the two-dimensional Euler equations for an incompressible fluid. This analogy with fluid dynamics gives a unified and intuitive framework to explain the beam spiraling and beam break up behavior observed in experiments and in simulations. In particular, we demonstrate that beam break up is the result of a classical instability occurring in fluids subject to a sheared flow. We give scaling laws for the instability and predict the nonlinear evolution of beams subject to it. Our work suggests that cyclotrons may be uniquely suited for the experimental study of shear layers and vortex distributions that are not achievable in Penning-Malmberg traps.

  11. Oscillatory motion of sheared nanorods beyond the nematic phase.

    Science.gov (United States)

    Strehober, David A; Engel, Harald; Klapp, Sabine H L

    2013-07-01

    We study the role of the control parameter triggering nematic order (temperature or concentration) on the dynamical behavior of a system of nanorods under shear. Our study is based on a set of mesoscopic equations of motion for the components of the tensorial orientational order parameter. We investigate these equations via a systematic bifurcation analysis based on a numerical continuation technique, focusing on spatially homogeneous states. Exploring a wide range of parameters we find, unexpectedly, that states with oscillatory motion can exist even under conditions where the equilibrium system is isotropic. These oscillatory states are characterized by a wagging motion of the paranematic director, and they occur if the tumbling parameter is sufficiently small. We also present full nonequilibrium phase diagrams in the plane spanned by the concentration and the shear rate.

  12. Miscible displacement fronts of shear thinning fluids inside rough fractures

    CERN Document Server

    Boschan, A; Ippolito, I; Chertcoff, R; Hulin, J P; Boschan, Alexandro; Auradou, Harold; Ippolito, Irene; Chertcoff, Ricardo; Hulin, Jean-Pierre

    2006-01-01

    The miscible displacement of a shear-thinning fluid by another of same rheological properties is studied experimentally in a transparent fracture by an optical technique imaging relative concentration distributions. The fracture walls have complementary self-affine geometries and are shifted laterally in the direction perpendicular to the mean flow velocity {\\bf U} : the flow field is strongly channelized and macro dispersion controls the front structure for P\\'{e}clet numbers above a few units. The global front width increases then linearly with time and reflects the velocity distribution between the different channels. In contrast, at the local scale, front spreading is similar to Taylor dispersion between plane parallel surfaces. Both dispersion mechanisms depend strongly on the fluid rheology which shifts from Newtonian to shear-thinning when the flow rate increases. In the latter domain, increasing the concentration enhances the global front width but reduces both Taylor dispersion (due to the flattening...

  13. Oscillatory motion of sheared nanorods beyond the nematic phase

    Science.gov (United States)

    Strehober, David A.; Engel, Harald; Klapp, Sabine H. L.

    2013-07-01

    We study the role of the control parameter triggering nematic order (temperature or concentration) on the dynamical behavior of a system of nanorods under shear. Our study is based on a set of mesoscopic equations of motion for the components of the tensorial orientational order parameter. We investigate these equations via a systematic bifurcation analysis based on a numerical continuation technique, focusing on spatially homogeneous states. Exploring a wide range of parameters we find, unexpectedly, that states with oscillatory motion can exist even under conditions where the equilibrium system is isotropic. These oscillatory states are characterized by a wagging motion of the paranematic director, and they occur if the tumbling parameter is sufficiently small. We also present full nonequilibrium phase diagrams in the plane spanned by the concentration and the shear rate.

  14. The influence of water and LPO on the initiation and evolution of mantle shear zones

    Science.gov (United States)

    Skemer, Philip; Warren, Jessica M.; Hansen, Lars N.; Hirth, Greg; Kelemen, Peter B.

    2013-08-01

    We present data from the Josephine Peridotite (SW Oregon, USA) that constrain the underlying physical processes responsible for the initiation of shear localization and the evolution of ductile shear zones in Earth's mantle. Field measurements of narrow (2-60 m wide) ductile shear zones in harzburgite were used to construct strain profiles, which have maximum shear strains ranging from γ=5.25 to γ>20. Measurements of pyroxene water concentrations from harzburgite samples within and immediately adjacent to the shear zones indicate that gradients in water concentration exist on a 10-100 m scale, even after exhumation. Water concentration measurements are correlated with olivine lattice-preferred orientation (LPO), corroborating experimental results on the influence of water on slip system activity. Using empirical olivine flow laws and the diffusivity of water in olivine, we model initiation of a ductile shear zone through localized water weakening. We demonstrate that this mechanism can readily generate spatial perturbations in both effective viscosity and strain. However this model is not able to reproduce both the observed shear strain gradients and water concentration data from the Josephine shear zones. We evaluate other plausible localization mechanisms, which may amplify this initial strain perturbation. The most relevant at these conditions is the development of viscous anisotropy associated with the evolution of olivine LPO. Using recent experimental results, we demonstrate that progressive rotation of olivine LPO into the shear plane enhances deformation within a shear zone. We conclude that feedback between at least two microphysical processes is needed to account for observed outcrop-scale shear localization.

  15. On rank 5 projective planes

    Directory of Open Access Journals (Sweden)

    Otto Bachmann

    1984-01-01

    Full Text Available In this paper we continue the study of projective planes which admit collineation groups of low rank (Kallaher [1] and Bachmann [2,3]. A rank 5 collineation group of a projective plane ℙ of order n≠3 is proved to be flag-transitive. As in the rank 3 and rank 4 case this implies that is ℙ not desarguesian and that n is (a prime power of the form m4 if m is odd and n=m2 with m≡0mod4 if n is even. Our proof relies on the classification of all doubly transitive groups of finite degree (which follows from the classification of all finite simple groups.

  16. Hydrodynamics of planing monohull watercraft

    CERN Document Server

    Vorus, William S

    2017-01-01

    This book addresses the principles involved in the design and engineering of planing monohull power boats, with an emphasis on the theoretical fundamentals that readers need in order to be fully functional in marine design and engineering. Author William Vorus focuses on three topics: boat resistance, seaway response, and propulsion and explains the physical principles, mathematical details, and theoretical details that support physical understanding. In particular, he explains the approximations and simplifications in mathematics that lead to success in the applications of planing craft design engineering, and begins with the simplest configuration that embodies the basic physics. He leads readers, step-by-step, through the physical complications that occur, leading to a useful working knowledge of marine design and engineering. Included in the book are a wealth of examples that exemplify some of the most important naval architecture and marine engineering problems that challenge many of today’s engineers.

  17. Plane waves as tractor beams

    CERN Document Server

    Forgács, Péter; Romańczukiewicz, Tomasz

    2013-01-01

    It is shown that in a large class of systems plane waves can act as tractor beams: i.e., an incident plane wave can exert a pulling force on the scatterer. The underlying physical mechanism for the pulling force is due to the sufficiently strong scattering of the incoming wave into another mode having a larger wave number, in which case excess momentum is created behind the scatterer. Such a tractor beam or negative radiation pressure effect arises naturally in systems where the coupling between the scattering channels is due to Aharonov-Bohm (AB) gauge potentials. It is demonstrated that this effect is also present if the AB potential is an induced, ("artificial") gauge potential such as the one found in J. March-Russell, J. Preskill, F. Wilczek, Phys. Rev. Lett. 58 2567 (1992).

  18. Eight plane IPND mechanical testing.

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, A.; Guarino, V.; Wood, K.; Nephew, T.; Ayres, D.; Lee, A.; High Energy Physics; FNAL

    2008-03-18

    A mechanical test of an 8 plane IPND mechanical prototype, which was constructed using extrusions from the testing/tryout of the 16 cell prototype extrusion die in Argonne National Laboratory, was conducted. There were 4 vertical and 4 horizontal planes in this 8 plane IPND prototype. Each vertical plane had four 16 cell extrusions, while each horizontal plane had six 16 cell extrusions. Each plane was glued together using the formulation of Devcon adhesive, Devcon 60. The vertical extrusions used in the vertical planes shares the same dimensions as the horizontal extrusions in the horizontal planes with the average web thickness of 2.1 mm and the average wall thickness of 3.1 mm. This mechanical prototype was constructed with end-seals on the both ends of the vertical extrusions. The gaps were filled with epoxy between extrusions and end-seals. The overall dimension of IPND is 154.8 by 103.1 by 21.7 inches with the weight of approximately 1200 kg, as shown in a figure. Two similar mechanical tests of 3 layer and 11 layer prototypes have been done in order to evaluate the strength of the adhesive joint between extrusions in the NOvA detector. The test showed that the IPND prototype was able to sustain under the loading of weight of itself and scintillator. Two FEA models were built to verify the measurement data from the test. The prediction from FEA slice model seems correlated reasonably well to the test result, even under a 'rough' estimated condition for the wall thickness (from an untuned die) and an unknown property of 'garage type' extrusion. A full size of FEA 3-D model also agrees very well with the test data from strain gage readings. It is worthy to point out that the stress distribution of the structure is predominantly determined by the internal pressure, while the buckling stability relies more on the loading weight from the extrusions themselves and scintillate. Results of conducted internal pressure tests, including 3- cell, 11

  19. Ab initio studies of two Al grain boundaries subjected to mixed tension/shear mode loading: how shear may promote breakage

    Science.gov (United States)

    Ehlers, F. J. H.; Seydou, M.; Tingaud, D.; Maurel, F.; Queyreau, S.; Charles, Y.

    2017-09-01

    Using the framework of density functional theory, the structural and energetic response of two face-centred cubic (fcc) Al grain boundaries (GBs) to combined tension and shear loadings has been examined. It is shown that tension will serve to inhibit the Σ5 [100] 36.87° twist GB response to shear in a mixed-mode loading scenario, by increasing the difference in structural environments for inequivalent atoms at the GB plane. We propose that the presence of such atoms, rather than the full structural details of the GB structure, is instrumental in triggering this tension-shear interplay. As support for this hypothesis, we compute the Σ3 [-110] (111) 60° symmetric tilt GB mixed-mode loading response. Here, all atoms at the GB plane are equivalent, and the qualitative shear energy variation is unaffected by tension. Our findings indicate that general fcc Al GBs may display a stronger shear energy variation at larger levels of tension, contrasting general expectations. The implications to GB breakage are discussed.

  20. Force Lines in Plane Stress

    DEFF Research Database (Denmark)

    Rathkjen, Arne

    A state of plane stress is illustrated by means of two families of curves, each family representing constant values of a derivative of Airy's stress function. The two families of curves form a map giving in the first place an overall picture of regions of high and low stress, and in the second...... place, the map comprises a complete graphic representation of the stress at any point....

  1. Experimental observation of shear thickening oscillation

    DEFF Research Database (Denmark)

    Nagahiro, Shin-ichiro; Nakanishi, Hiizu; Mitarai, Namiko

    2013-01-01

    We report experimental observations of the shear thickening oscillation, i.e. the spontaneous macroscopic oscillation in the shear flow of severe shear thickening fluid. Using a density-matched starch-water mixture, in the cylindrical shear flow of a few centimeters flow width, we observed...

  2. Numerical simulation of influence of shear dilatancy on deformation characteristics of shear band-elastic body system

    Institute of Scientific and Technical Information of China (English)

    WANG Xue-bin

    2004-01-01

    The paper was numerically focused on investigation of deformation, failure and instability of shear band-surrounding elastic rock system in plane strain direct shear test considering shear dilatancy according to fast lagrangian analysis of continua (FLAC). The adopted failure criterion was a composite Mohr-Coulomb criterion with tension cut-off and post-peak constitutive relation of rock, i.e. linear strain-softening. Numerical results show that dilation angle affects the responses of elements, the number and the position of yielded elements. Increasing dilation angle results in higher load-carrying capability of elements, higher deformation or strain corresponding to peak stress, less brittle post-peak stress-deformation curve. Strain-hardening behavior can occur if dilation angle is high.Therefore, shear band-elastic rock body system tends to be stable and rock burst does not occur as dilation angle is increased. Moreover, the number of yielded elements is increased with dilation angle increase and two parallel plastic zones initially generated in the middle of two loading ends of specimen no longer remain collinear, reflecting increase in deformation resistant of the system. Evolution of volumetric strain rate was investigated based on three-dimensional curved surface diagrams. Approximately, volumetric strain rate concentration regions coincide with plastic zones. Volumetric strain rate in yielded elements is very evident. However, in elastic zones volumetric strain has not been nearly changed throughout the numerical tests.

  3. Shear elasticity of fluids at low-frequent shear influence.

    Science.gov (United States)

    Badmaev, Badma B; Budaev, Ochir R; Dembelova, Tuyana S; Damdinov, Bair B

    2006-12-22

    The visco-elastic properties of liquids have been investigated using acoustical resonance method. Piezoquatrz performed tangential oscillations on the main resonance frequency of 74 kHz contacts by the one end of horizontal surface with the studied liquid layer covered by quartz cover-plate. So the stagnant shear waves are installed in layer. The solution of interaction of piezoquartz-liquid layer-cover-plate gives three methods of determination of the real shear modulus (G) and the tangent of mechanical loss angle (tan theta) of liquid. The first method is realized at smaller thickness of liquid layer then the length of shear wave. Liquids of different classes have been studied using this method: polymer liquids, oils, glycols and alcohols. The second method is connected with the propagation of shear wave in liquid layer, parameters of which are determined the G and tan theta. And the third method is based on the determination of limit shift of resonance frequencies at completes damping of shear wave in thick layer of liquid. All these three methods give satisfactory agreement of results.

  4. An analytical-based method for studying the nonlinear evolution of localized vortices in planar homogenous shear flows

    Science.gov (United States)

    Cohen, J.; Shukhman, I. G.; Karp, M.; Philip, J.

    2010-10-01

    Recent experimental and numerical studies have shown that the interaction between a localized vortical disturbance and the shear of an external base flow can lead to the formation of counter-rotating vortex pairs and hairpin vortices that are frequently observed in wall bounded and free turbulent shear flows as well as in subcritical shear flows. In this paper an analytical-based solution method is developed. The method is capable of following (numerically) the evolution of finite-amplitude localized vortical disturbances embedded in shear flows. Due to their localization in space, the surrounding base flow is assumed to have homogeneous shear to leading order. The method can solve in a novel way the interaction between a general family of unbounded planar homogeneous shear flows and any localized disturbance. The solution is carried out using Lagrangian variables in Fourier space which is convenient and enables fast computations. The potential of the method is demonstrated by following the evolved structures of large amplitude disturbances in three canonical base flows, including simple shear, plane stagnation (extensional) and pure rotation flows, and a general case. The results obtained by the current method for plane stagnation and simple shear flows are compared with the published results. The proposed method could be extended to other flows (e.g. geophysical and rotating flows) and to include periodic disturbances as well.

  5. Instability of subharmonic resonances in magnetogravity shear waves.

    Science.gov (United States)

    Salhi, A; Nasraoui, S

    2013-12-01

    We study analytically the instability of the subharmonic resonances in magnetogravity waves excited by a (vertical) time-periodic shear for an inviscid and nondiffusive unbounded conducting fluid. Due to the fact that the magnetic potential induction is a Lagrangian invariant for magnetohydrodynamic Euler-Boussinesq equations, we show that plane-wave disturbances are governed by a four-dimensional Floquet system in which appears, among others, the parameter ɛ representing the ratio of the periodic shear amplitude to the vertical Brunt-Väisälä frequency N(3). For sufficiently small ɛ and when the magnetic field is horizontal, we perform an asymptotic analysis of the Floquet system following the method of Lebovitz and Zweibel [Astrophys. J. 609, 301 (2004)]. We determine the width and the maximal growth rate of the instability bands associated with subharmonic resonances. We show that the instability of subharmonic resonance occurring in gravity shear waves has a maximal growth rate of the form Δ(m)=(3√[3]/16)ɛ. This instability persists in the presence of magnetic fields, but its growth rate decreases as the magnetic strength increases. We also find a second instability involving a mixing of hydrodynamic and magnetic modes that occurs for all magnetic field strengths. We also elucidate the similarity between the effect of a vertical magnetic field and the effect of a vertical Coriolis force on the gravity shear waves considering axisymmetric disturbances. For both cases, plane waves are governed by a Hill equation, and, when ɛ is sufficiently small, the subharmonic instability band is determined by a Mathieu equation. We find that, when the Coriolis parameter (or the magnetic strength) exceeds N(3)/2, the instability of the subharmonic resonance vanishes.

  6. Waveguide characteristics of coupled in-plane waves.

    Science.gov (United States)

    Pan, Jie; Lu, Jing; Qiu, Xiaojun

    2012-06-01

    In-plane waves in a waveguide made from a thin plate are described by a superposition of a set of orthogonal functions that satisfy the edge conditions of the waveguide. Due to the Poisson and shear effects, the displacement components of the in-plane waves along the two in-plane orthogonal coordinates are coupled and this coupling affects the propagation and spatial properties of the waveguide modes. The orthogonal functions and their associated wavenumbers represent the characteristics of the uncoupled modes of the waveguide where the above mentioned couplings are ignored. This study demonstrates that the characteristics of the waveguide modes are determined by the couplings of the uncoupled mode pairs, which become significant when the pairs satisfy the conditions of spatial coincidence. At some frequencies, certain waveguide modes can be determined by a single pair of uncoupled modes. For this case, the analytical solution for the waveguide modes exists and provides both a qualitative and quantitative interpretation of the characteristics of the waveguide mode.

  7. Temperature-dependent ideal strength and stacking fault energy of fcc Ni: a first-principles study of shear deformation.

    Science.gov (United States)

    Shang, S L; Wang, W Y; Wang, Y; Du, Y; Zhang, J X; Patel, A D; Liu, Z K

    2012-04-18

    Variations of energy, stress, and magnetic moment of fcc Ni as a response to shear deformation and the associated ideal shear strength (τ(IS)), intrinsic (γ(SF)) and unstable (γ(US)) stacking fault energies have been studied in terms of first-principles calculations under both the alias and affine shear regimes within the {111} slip plane along the and directions. It is found that (i) the intrinsic stacking fault energy γ(SF) is nearly independent of the shear deformation regimes used, albeit a slightly smaller value is predicted by pure shear (with relaxation) compared to the one from simple shear (without relaxation); (ii) the minimum ideal shear strength τ(IS) is obtained by pure alias shear of {111}; and (iii) the dissociation of the 1/2[110] dislocation into two partial Shockley dislocations (1/6[211] + 1/6[121]) is observed under pure alias shear of {111}. Based on the quasiharmonic approach from first-principles phonon calculations, the predicted γ(SF) has been extended to finite temperatures. In particular, using a proposed quasistatic approach on the basis of the predicted volume versus temperature relation, the temperature dependence of τ(IS) is also obtained. Both the γ(SF) and the τ(IS) of fcc Ni decrease with increasing temperature. The computed ideal shear strengths as well as the intrinsic and unstable stacking fault energies are in favorable accord with experiments and other predictions in the literature.

  8. Analysis of shear band instabilities in sintered metals

    DEFF Research Database (Denmark)

    Redanz, Pia; Tvergaard, Viggo

    1999-01-01

    of a material instability. The elastic plastic behaviour of the material is represented by a material model, which combines the Gurson model, relevant to rather low porosities, with the FKM model, developed for high porosity powder compacts. Predictions are shown for various levels of initial porosity...... and for various levels of initial material:imperfections, considering both plane strain and axisymmetric conditions outside the shear band. Also a comparison of localization predictions by the Gurson model, the FKM model and the combined model is presented. (C) 1999 Elsevier Science Ltd. All rights reserved....

  9. On the origin of streaks in turbulent shear flows

    Science.gov (United States)

    Waleffe, Fabian; Kim, John

    1991-01-01

    The paper substantiates the notion that selective amplification and direct resonance, based on linear theory, does not provide a selection mechanism for the well-defined streak spacing of about 100 wall units observed in wall-bounded turbulent shear flows. For the direct resonance theory, it is shown that the streaks are created by the nonlinear self-interaction of the vertical velocity rather than that of the directly forced vertical vorticity. It is proposed that the selection mechanism must be inherently nonlinear and correspond to a self-sustaining process. For the case of plane Poiseuille flow the 100-wall-unit criterion corresponds to a critical Reynolds number of 1250, based on the centerline velocity and the channel half-width, which is close to the usually quoted value of about 1000. In plane Couette flow, it corresponds to a critical Reynolds number of 625, based on the half-velocity difference and the half-width.

  10. Modelling the Shear-Tension Coupling of Woven Engineering Fabrics

    Directory of Open Access Journals (Sweden)

    F. Abdiwi

    2013-01-01

    Full Text Available An approach to incorporate the coupling between the shear compliance and in-plane tension of woven engineering fabrics, in finite-element-based numerical simulations, is described. The method involves the use of multiple input curves that are selectively fed into a hypoelastic constitutive model that has been developed previously for engineering fabrics. The selection process is controlled by the current value of the in-plane strain along the two fibre directions using a simple algorithm. Model parameters are determined from actual experimental data, measured using the Biaxial Bias Extension test. An iterative process involving finite element simulations of the experimental test is used to normalise the test data for use in the code. Finally, the effectiveness of the method is evaluated and shown to provide qualitatively good predictions.

  11. Two multilayered plate models with transverse shear warping functions issued from three dimensional elasticity equations

    CERN Document Server

    Loredo, Alexandre

    2013-01-01

    A multilayered plate theory which uses transverse shear warping functions issued from three-dimensional elasticity is presented. Two methods to obtain these transverse shear warping functions are detailed. The warping functions are issued from the variations of transverse shear stresses computed at special location points for a simply supported bending problem. The first method considers an exact 3D solution of the problem. The second method uses the solution provided by the model itself: the transverse shear stresses are computed by the integration of equilibrium equations. Hence, an iterative process is applied, the model being updated with the new warping functions, and so on. These two models are compared to other models and to analytical solutions for the bending of simply supported plates. Four different laminates and a sandwich are considered, length-to-thickness values varying from 2 to 100. An additional analytical solution that simulates the behavior of laminates under the plane stress hypothesis - ...

  12. Energy trapping of thickness-shear vibration modes of elastic plates with functionally graded materials.

    Science.gov (United States)

    Wang, Ji; Yang, Jiashi; Li, Jiangyu

    2007-03-01

    Energy trapping has important applications in the design of thickness-shear resonators. Considerable efforts have been made for the effective utilization and improvement of energy trapping with variations of plate configurations, such as adding electrodes and contouring. As a new approach in seeking improved energy trapping feature, we analyze thickness-shear vibrations in an elastic plate with functionally graded material (FGM) of in-plane variation of mechanical properties, such as elastic constants and density. A simple and general equation governing the thickness-shear modes is derived from a variational analysis. A plate with piecewise constant material properties is analyzed as an example. It is shown that such a plate can support thickness-shear vibration modes with obvious energy trapping. Bechmann's number for the existence of only one trapped mode also can be determined accordingly.

  13. Behaviour Of Multi-Storied Flat Slab Building Considering Shear Walls: A Review

    Directory of Open Access Journals (Sweden)

    Dhanaji R. Chavan

    2016-10-01

    Full Text Available Recently there has been a considerable increase in the number of tall buildings, both residential and commercial, and modern trend is towards taller structures. Flat slab is most widely used systems in reinforced concrete construction. Flat-slab building structures possesses major advantages over traditional slab-beam-column structures taking a advantages of reduced floor height, shorter construction time, architectural –functional and economical aspects. But in flat slab building columns are directly provides supports to slab with eliminating beams so there is requirement of provision of shear walls to increase the stiffness of building against lateral forces. Shear wall system are one of the most commonly used lateral load resisting in high rise building. Shear wall has high in plane stiffness and strength. The present paper reviews various research works carried out by several researchers on multi-storied buildings provided with flat slab and shear walls.

  14. Quantitative calculation of local shear deformation in adiabatic shear band for Ti-6Al-4V

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    JOHNSON-COOK(J-C) model was used to calculate flow shear stress-shear strain curve for Ti-6Al-4V in dynamic torsion test. The predicted curve was compared with experimental result. Gradient-dependent plasticity(GDP) was introduced into J-C model and GDP was involved in the measured flow shear stress-shear strain curve, respectively, to calculate the distribution of local total shear deformation(LTSD) in adiabatic shear band(ASB). The predicted LTSDs at different flow shear stresses were compared with experimental measurements. J-C model can well predict the flow shear stress-shear strain curve in strain-hardening stage and in strain-softening stage where flow shear stress slowly decreases. Beyond the occurrence of ASB, with a decrease of flow shear stress, the increase of local plastic shear deformation in ASB is faster than the decrease of elastic shear deformation, leading to more and more apparent shear localization. According to the measured flow shear stress-shear strain curve and GDP, the calculated LTSDs in ASB are lower than experimental results. At earlier stage of ASB, though J-C model overestimates the flow shear stress at the same shear strain, the model can reasonably assess the LTSDs in ASB. According to the measured flow shear stress-shear strain curve and GDP, the calculated local plastic shear strains in ASB agree with experimental results except for the vicinity of shear fracture surface. In the strain-softening stage where flow shear stress sharply decreases, J-C model cannot be used. When flow shear stress decreases to a certain value, shear fracture takes place so that GDP cannot be used.

  15. Development of quartz c-axis crossed/single girdles under simple-pure shear deformation: Results of visco-plastic self-consistent modeling

    Science.gov (United States)

    Nie, Guanjun; Shan, Yehua

    2014-09-01

    Quartz c-axis fabrics are widely used to determine the shear plane in ductile shear zones, based upon an assumption that the shear plane is perpendicular to both the central segment of quartz c-axis crossed girdle and single girdle. In this paper the development of quartz c-axis fabric under simple-pure shear deformation is simulated using the visco-plastic self-consistent (VPSC) model so as to re-examine this assumption. In the case of no or weak dynamic recrystallization, the simulated crossed girdles have a central segment perpendicular or nearly perpendicular to the maximum principal finite strain direction (X) and the XY finite strain plane, and at a variable angle relative to the imposed kinematic framework that is dependent on the modeled flow vorticity and finite strain. These crossed girdles have a symmetrical skeleton with respect to the finite strain axes, regardless of the bulk strain and the kinematic vorticity, and rotate in a way similar to the shear sense with increasing bulk strain ratio. The larger the vorticity number the more asymmetrical their legs tend to be. In the case of strong dynamic recrystallization and large bulk strain, under simple shear the crossed girdle switches into single girdles, sub-perpendicular to the shear plane, by losing the weak legs. The numerical results in our models do not confirm the above-mentioned assumption.

  16. Shear Acceleration in Expanding Flows

    CERN Document Server

    Rieger, F M

    2016-01-01

    Shear flows are naturally expected to occur in astrophysical environments and potential sites of continuous non-thermal Fermi-type particle acceleration. Here we investigate the efficiency of expanding relativistic outflows to facilitate the acceleration of energetic charged particles to higher energies. To this end, the gradual shear acceleration coefficient is derived based on an analytical treatment. The results are applied to the context of the relativistic jets of active galactic nuclei. The inferred acceleration timescale is investigated for a variety of conical flow profiles (i.e., power law, Gaussian, Fermi-Dirac) and compared to the relevant radiative and non-radiative loss timescales. The results exemplify that relativistic shear flows are capable of boosting cosmic-rays to extreme energies. Efficient electron acceleration, on the other hand, requires weak magnetic fields and may thus be accompanied by a delayed onset of particle energization and affect the overall jet appearance (e.g., core, ridge ...

  17. SNAP Satellite Focal Plane Development

    Energy Technology Data Exchange (ETDEWEB)

    Bebek, C.; Akerlof, C.; Aldering, G.; Amanullah, R.; Astier, P.; Baltay, C.; Barrelet, E.; Basa, S.; Bercovitz, J.; Bergstrom, L.; Berstein, G.P.; Bester, M.; Bohlin, R.; Bonissent, A.; Bower, C.; Campbell, M.; Carithers, W.; Commins, E.; Day, C.; Deustua, S.; DiGennaro, R.; Ealet, A.; Ellis, R.; Emmett, W.; Eriksson, M.; Fouchez,D.; Fruchter, A.; Genat, J-F.; Goldhaber, G.; Goobar, A.; Groom, D.; Heetderks, H.; Holland, S.; Huterer, D.; Johnson, W.; Kadel, R.; Karcher,A.; Kim, A.; Kolbe, W.; Lafever, R.; Lamoureaux, J.; Lampton, M.; Lefevre, O.; Levi, M.; Levin, D.; Linder, E.; Loken, S.; Malina, R.; Mazure, A.; McKay, T.; McKee, S.; Miquel, R.; Morgan, N.; Mortsell, E.; Mostek, N.; Mufson, S.; Musser, J.; Roe, N.; Nugent, P.; Oluseyi, H.; Pain, R.; Palaio, N.; Pankow, D.; Perlmutter, S.; Prieto, E.; Rabinowitz,D.; Refregier, A.; Rhodes, J.; Schubnell, M.; Sholl, M.; Smadja, G.; Smith, R.; Smoot, G.; Snyder, J.; Spadafora, A.; Szymkowiak, A.; Tarle,G.; Taylor, K.; Tilquin, A.; Tomasch, A.; Vincent, D.; von der Lippe, H.; Walder, J-P.; Wang, G.

    2003-07-07

    The proposed SuperNova/Acceleration Probe (SNAP) mission will have a two-meter class telescope delivering diffraction-limited images to an instrumented 0.7 square degree field in the visible and near-infrared wavelength regime. The requirements for the instrument suite and the present configuration of the focal plane concept are presented. A two year R&D phase, largely supported by the Department of Energy, is just beginning. We describe the development activities that are taking place to advance our preparedness for mission proposal in the areas of detectors and electronics.

  18. Homoclinic snaking in plane Couette flow: bending, skewing, and finite-size effects

    CERN Document Server

    Gibson, John F

    2015-01-01

    Invariant solutions of shear flows have recently been extended from spatially periodic solutions in minimal flow units to spatially localized solutions on extended domains. One set of spanwise-localized solutions of plane Couette flow exhibits homoclinic snaking, a process by which steady-state solutions grow additional structure smoothly at their fronts when continued parametrically. Homoclinic snaking is well understood mathematically in the context of the one-dimensional Swift-Hohenberg equation. Consequently, the snaking solutions of plane Couette flow form a promising connection between the largely phenomenological study of laminar-turbulent patterns in viscous shear flows and the mathematically well-developed field of pattern-formation theory. In this paper we present a numerical study of the snaking solutions, generalizing beyond the fixed streamwise wavelength of previous studies. We find a number of new solution features, including bending, skewing, and finite-size effects. We show that the finite-si...

  19. Analysis of bonded anisotropic wedges with interface crack under anti-plane shear loading

    Institute of Scientific and Technical Information of China (English)

    M.GHADIRI; A.R.SHAHANI

    2014-01-01

    The antiplane stress analysis of two anisotropic finite wedges with arbitrary radii and apex angles that are bonded together along a common edge is investigated. The wedge radial boundaries can be subjected to displacement-displacement boundary condi-tions, and the circular boundary of the wedge is free from any traction. The new finite complex transforms are employed to solve the problem. These finite complex transforms have complex analogies to both kinds of standard finite Mellin transforms. The traction free condition on the crack faces is expressed as a singular integral equation by using the exact analytical method. The explicit terms for the strength of singularity are extracted, showing the dependence of the order of the stress singularity on the wedge angle, material constants, and boundary conditions. A numerical method is used for solving the resul-tant singular integral equations. The displacement boundary condition may be a general term of the Taylor series expansion for the displacement prescribed on the radial edge of the wedge. Thus, the analysis of every kind of displacement boundary conditions can be obtained by the achieved results from the foregoing general displacement boundary condition. The obtained stress intensity factors (SIFs) at the crack tips are plotted and compared with those obtained by the finite element analysis (FEA).

  20. Experimental Investigation on the Effects of Chemical Heat Release in the Reacting Turbulent Plane Shear Layer.

    Science.gov (United States)

    1981-01-01

    detailed comparison between experimental and predicted profiles is made in Section 3.2 IIH 71. a0.21 U c 9.2 CL) 0 - .0-.005 . .5y Fi . 31 feto nMaue...eprtr rfls 72. b) 1.1 cc 010 - . . . h.y Fi.31 feto nTmeauePoie nerdfo Kords Ds 73. but this discussion concerns the effects of changing F. The three

  1. Real-Time Adaptive Control of Mixing in a Plane Shear Layer

    Science.gov (United States)

    1992-01-01

    surface neaters, cold wire I a O Ssensors, performance measure, pdf, piezo ~electric 3ctuactors 17. SICjUNT O.CANWAON1 IL. suojarr cLAssI.To~no it. sacurm...between the primary vortical structures. At this downstream location, the flow has already begun pairing and hence the amplitude of the subharmonic is...number of spectral peaks, none of which can be classified as dominant. In addition, the subharmonic frequency band (i.e., around fN/2) shows a similar

  2. On free fermions and plane partitions

    CERN Document Server

    Foda, O; Zuparic, M

    2008-01-01

    We use free fermion methods to re-derive a result of Okounkov and Reshetikhin relating charged fermions to random plane partitions, and to extend it to relate neutral fermions to strict plane partitions.

  3. On poro-hyperelastic shear

    Science.gov (United States)

    Suvorov, A. P.; Selvadurai, A. P. S.

    2016-11-01

    The paper examines the problem of the shear of a porous hyperelastic material, the pore space of which is saturated with an incompressible fluid. Poro-hyperelasticity provides a suitable approach for modelling the mechanical behaviour of highly deformable materials in engineering applications and particularly soft tissues encountered in biomechanical applications. Unlike with the infinitesimal theory of poroelasticity, the application of pure shear generates pore fluid pressures that dissipate with time as fluid migrates either from or into the pore space due to the generated fluid pressure gradients. The analytical results provide benchmark problems that can be used to examine the accuracy of computational approaches.

  4. Shear loading of costal cartilage

    CERN Document Server

    Subit, Damien

    2014-01-01

    A series of tests were performed on a single post-mortem human subject at various length scales. First, tabletop tests were performed. Next, the ribs and intercostal muscles were tested with the view to characterize the load transfer between the ribs. Finally, the costal cartilage was tested under shear loading, as it plays an important in the transfer of the load between the ribs and the sternum. This paper reports the results of dynamic shear loading tests performed on three samples of costal cartilage harvested from a single post-mortem human subject, as well as the quantification of the effective Young's modulus estimated from the amount of cartilage calcification.

  5. Shear strength of non-shear reinforced concrete elements

    DEFF Research Database (Denmark)

    Hoang, Cao linh

    1997-01-01

    . The position of the crack in which sliding takes place is determined by the crack sliding model developed by Jin-Ping Zhang. The theoretical calculations are compared with test results reported in the literature. A good agreement has been found.A simplified method to calculate the shear capacity of T...

  6. Shear resistance of beams based on the effective shear depth

    NARCIS (Netherlands)

    Pruijssers, A.F.

    1986-01-01

    Despite extensive experimental and theoretical studies the shear resistance of beams with longitudinal reinforcement is described by empirical expressions. A reliable empirical formula is derived by Rafla [10]. This formula is based on 442 experimental results. In this report no experiments are

  7. Cosmic Shear Bias and Calibration in Cosmic Shear Studies

    CERN Document Server

    Taylor, A N

    2016-01-01

    With the advent of large-scale weak lensing surveys there is a need to understand how realistic, scale-dependent systematics bias cosmic shear and dark energy measurements, and how they can be removed. Here we describe how spatial variations in the amplitude and orientation of realistic image distortions convolve with the measured shear field, mixing the even-parity convergence and odd-parity modes, and bias the shear power spectrum. Many of these biases can be removed by calibration to external data, the survey itself, or by modelling in simulations. The uncertainty in the calibration must be marginalised over and we calculate how this propagates into parameter estimation, degrading the dark energy Figure-of-Merit. We find that noise-like biases affect dark energy measurements the most, while spikes in the bias power have the least impact, reflecting their correlation with the effect of cosmological parameters. We argue that in order to remove systematic biases in cosmic shear surveys and maintain statistica...

  8. Active Control of Shear Thickening in Suspensions

    CERN Document Server

    Lin, Neil Y C; Cates, Michael E; Sun, Jin; Cohen, Itai

    2016-01-01

    Shear thickening, an increase of viscosity with shear rate, is a ubiquitous phenomena in suspended materials that has implications for broad technological applications. Controlling this thickening behavior remains a major challenge and has led to empirical strategies ranging from altering the particle surfaces and shape to modifying the solvent properties. However, none of these methods allow for active control of flow properties during shear itself. Here, we demonstrate that by strategic imposition of a high-frequency and low-amplitude shear perturbation orthogonal to the primary shearing flow, we can largely eradicate shear thickening. The orthogonal shear effectively becomes a regulator for controlling thickening in the suspension, allowing the viscosity to be reduced by up to two decades on demand. In a separate setup, we show that such effects can be induced by simply agitating the sample transversely to the primary shear direction. Overall, the ability of in situ manipulation of shear thickening paves a...

  9. Visualizing shear bands in 3-D using axisymmetric sample: An experimental study

    Directory of Open Access Journals (Sweden)

    W. Khraisat

    2017-07-01

    Full Text Available In this study a qualitative description of the occurrence of shear bands produced by a sudden impact on an axisymmetric specimen made of medium carbon steel 0.45% C is given. A simple experiment was developed aimed at producing a pinch shear stress in the front side of the test sample in order to visualize shear bands in 3-D. Curve fitting using MATLAB was employed based on the points taken from the images of the front section of the test sample. The predictions of the curve fitting suggests a hyperbolic section leading to the conclusion that within the sample there is a double cone region of material where the shear band region is located on its outer surface. The formation of the shear band is explained by the fact that the interaction of the stress wave front with the free surface of the test sample produces reflection waves that attenuate the incoming stress wave inwards leading to a stress gradient in the plane of the front side of the specimen that causes shear localization. Also, the progressively increasing cross sectional area of the test sample causes the expansion of the wave front, which also results in a stress gradient in the normal direction of the front side of the specimen. So the formation of shear bands depends not only on the impact momentum and strain rates but also on the sample’s geometry.

  10. Inverse method for the instantaneous measure of wall shear rate magnitude and direction using electrodiffusion probes

    Science.gov (United States)

    Lamarche-Gagnon, Marc-Etienne; Vetel, Jerome

    2016-11-01

    Several methods can be used when one needs to measure wall shear stress in a fluid flow. Yet, it is known that a precise shear measurement is seldom met, mostly when both time and space resolutions are required. The electrodiffusion method lies on the mass transfer between a redox couple contained in an electrolyte and an electrode flush mounted to a wall. Similarly to the heat transfer measured by a hot wire anemometer, the mass transfer can be related to the fluid's wall shear rate. When coupled with a numerical post-treatment by the so-called inverse method, precise instantaneous wall shear rate measurements can be obtained. With further improvements, it has the potential to be effective in highly fluctuating three-dimensional flows. We present developments of the inverse method to two-component shear rate measurements, that is shear magnitude and direction. This is achieved with the use of a three-segment electrodiffusion probe. Validation tests of the inverse method are performed in an oscillating plane Poiseuille flow at moderate pulse frequencies, which also includes reverse flow phases, and in the vicinity of a separation point where the wall shear stress experiences local inversion in a controlled separated flow.

  11. Shear strength of chromia across multiple length scales: An LDA + U study

    Energy Technology Data Exchange (ETDEWEB)

    Mosey, Nicholas J. [Department of Mechanical and Aerospace Engineering and Program in Applied and Computational Mathematics, Princeton University, Princeton, NJ 08544-5263 (United States); Carter, Emily A., E-mail: eac@princeton.edu [Department of Mechanical and Aerospace Engineering and Program in Applied and Computational Mathematics, Princeton University, Princeton, NJ 08544-5263 (United States)

    2009-06-15

    A method for predicting the shear strength of materials over multiple length scales is developed and tested. The method is based on renormalizing the energies and shear displacements obtained through electronic structure calculations of nanoscale models of the material of interest. All material- and size-dependent quantities are incorporated into the renormalization factors, yielding a universal model that can be applied to many materials and length scales. The model is used to predict the shear strength of Cr{sub 2}O{sub 3} along three relevant slip planes and slip directions. The results demonstrate that the shear strengths of the nanoscale systems used in the calculations range from 19.4 to 29.4 GPa. These data are then renormalized to predict the shear strength of a grain that is 10 {mu}m thick, yielding shear strengths ranging from 189 to 342 MPa. The large decrease in the shear strength with increasing grain size is consistent with the behavior of many materials. The ability to capture this change using electronic structure calculations that do not require experimental input may be useful in developing cohesive laws of novel materials for use in large-scale mechanical engineering simulations of materials failure.

  12. Image plane sweep volume illumination.

    Science.gov (United States)

    Sundén, Erik; Ynnerman, Anders; Ropinski, Timo

    2011-12-01

    In recent years, many volumetric illumination models have been proposed, which have the potential to simulate advanced lighting effects and thus support improved image comprehension. Although volume ray-casting is widely accepted as the volume rendering technique which achieves the highest image quality, so far no volumetric illumination algorithm has been designed to be directly incorporated into the ray-casting process. In this paper we propose image plane sweep volume illumination (IPSVI), which allows the integration of advanced illumination effects into a GPU-based volume ray-caster by exploiting the plane sweep paradigm. Thus, we are able to reduce the problem complexity and achieve interactive frame rates, while supporting scattering as well as shadowing. Since all illumination computations are performed directly within a single rendering pass, IPSVI does not require any preprocessing nor does it need to store intermediate results within an illumination volume. It therefore has a significantly lower memory footprint than other techniques. This makes IPSVI directly applicable to large data sets. Furthermore, the integration into a GPU-based ray-caster allows for high image quality as well as improved rendering performance by exploiting early ray termination. This paper discusses the theory behind IPSVI, describes its implementation, demonstrates its visual results and provides performance measurements.

  13. The INTEGRAL Galactic Plane Scanning

    CERN Document Server

    Fiocchi, Mariateresa

    2013-01-01

    After the first nine years of INTEGRAL operational life, the discovery of new sources and source types, a large fraction of which are highly transient or highly absorbed, is certainly one of the most compelling results and legacies of INTEGRAL. Frequent monitoring of the Galactic Plane in AO8 and AO9 campaigns allowed us to detect transient sources, both known and new, confirming that the gamma-ray sky is dominated by the extreme variability of different classes of objects. Regular scans of the Galactic Plane by INTEGRAL provide the most sensitive hard X-ray wide survey to date of our Galaxy, with flux limits of the order of 0.3 mCrab for an exposure time of ~2Ms. Many transient sources have been detected on a wide range of time scales (~hours to months) and identified by triggered followup observations, mainly by Swift/XRT and optical/infrared telescopes. These discoveries are very important to characterize the X-ray binary population in our Galaxy, that is necessary input for evolution studies. The transien...

  14. The HAWC Galactic Plane Survey

    Science.gov (United States)

    Hui, Michelle

    2016-03-01

    The High Altitude Water Cherenkov (HAWC) Observatory is an all-sky surveying instrument that covers 2/3 of the sky in 24 hours. It is designed with an emphasis on continuous sky coverage for transient events, and on the measurement of extended and large-scale structures. The array is located in Sierra Negra, Mexico at an elevation of 4,100 m and was inaugurated in March 2015. The HAWC array consists of 300 water Cherenkov detectors and is sensitive to extensive air showers triggered by cosmic rays and gamma rays from 100 GeV to >100 TeV. Thanks to its modular design, data taking began in Summer 2013 with 1/3 of the array. Analysis of the first year of data with the partial array shows detections that are coincident with known TeV supernova remnants and pulsar wind nebulae along the Galactic plane. Spectral and morphological analyses are ongoing to study the particle population and acceleration mechanism of these objects. With a growing data set taken with the completed array, source searches are underway for both point-like and extended emission along the Galactic plane, which contain many objects such as pulsar wind nebulae, young star clusters, and binaries.

  15. Lines, Circles, Planes and Spheres

    CERN Document Server

    Purdy, George B

    2009-01-01

    Let $S$ be a set of $n$ points in $\\mathbb{R}^3$, no three collinear and not all coplanar. If at most $n-k$ are coplanar and $n$ is sufficiently large, the total number of planes determined is at least $1 + k \\binom{n-k}{2}-\\binom{k}{2}(\\frac{n-k}{2})$. For similar conditions and sufficiently large $n$, (inspired by the work of P. D. T. A. Elliott in \\cite{Ell67}) we also show that the number of spheres determined by $n$ points is at least $1+\\binom{n-1}{3}-t_3^{orchard}(n-1)$, and this bound is best possible under its hypothesis. (By $t_3^{orchard}(n)$, we are denoting the maximum number of three-point lines attainable by a configuration of $n$ points, no four collinear, in the plane, i.e., the classic Orchard Problem.) New lower bounds are also given for both lines and circles.

  16. Singularities from colliding plane gravitational waves

    Science.gov (United States)

    Tipler, Frank J.

    1980-12-01

    A simple geometrical argument is given which shows that a collision between two plane gravitational waves must result in singularities. The argument suggests that these singularities are a peculiar feature of plane waves, because singularities are also a consequence of a collision between self-gravitating plane waves of other fields with arbitrarily small energy density.

  17. Singularities from colliding plane gravitational waves

    Energy Technology Data Exchange (ETDEWEB)

    Tipler, F.J.

    1980-12-15

    A simple geometrical argument is given which shows that a collision between two plane gravitational waves must result in singularities. The argument suggests that these singularities are a peculiar feature of plane waves, because singularities are also a consequence of a collision between self-gravitating plane waves of other fields with arbitrarily small energy density.

  18. Evolved stars in galactic plane surveys

    NARCIS (Netherlands)

    Verbeek, K.

    2013-01-01

    For the first time in history the entire Galactic Plane is digitally mapped from La Palma and Chile by the European Galactic Plane surveys EGAPS (UVEX, IPHAS and VPHAS+, see http://www.uvexsurvey.org http://www.iphas.org and http://www.vphasplus.org). The complete Galactic plane (3600 square degrees

  19. Homogeneity and plane-wave limits

    CERN Document Server

    Figueroa-O'Farrill, J M; Philip, S; Farrill, Jos\\'e Figueroa-O'; Meessen, Patrick; Philip, Simon

    2005-01-01

    We explore the plane-wave limit of homogeneous spacetimes. For plane-wave limits along homogeneous geodesics the limit is known to be homogeneous and we exhibit the limiting metric in terms of Lie algebraic data. This simplifies many calculations and we illustrate this with several examples. We also investigate the behaviour of (reductive) homogeneous structures under the plane-wave limit.

  20. Experimental observation of shear thickening oscillation

    CERN Document Server

    Nagahiro, Shin-ichiro; Mitarai, Namiko

    2012-01-01

    We report experimental observation of the shear thickening oscillation, i.e. the spontaneous macroscopic oscillation in the shear flow of severe shear thickening fluid. The shear thickening oscillation is caused by the interplay between the fluid dynamics and the shear thickening, and has been predicted theoretically by the present authors using a phenomenological fluid dynamics model for the dilatant fluid, but never been reported experimentally. Using a density-matched starch-water mixture, in the cylindrical shear flow of a few centimeters flow width, we observed strong vibrations of the frequency around 20 Hz, which is consistent with our theoretical prediction.

  1. Unexpected shear strength change in magnetorheological fluids

    Directory of Open Access Journals (Sweden)

    Yu Tian

    2014-09-01

    Full Text Available Smart materials of magnetorheological (MR fluids could be turned from a liquid state into a solid state, which solidification extent or shear strength often increases monotonically with the applied magnetic field. In this study, the shear stress of a dilute MR fluid decreased with increasing applied magnetic field at a constant shear rate. The dynamic shear stress was significantly higher than the stable counterpart at medium magnetic fields. They are ascribed to the slow particle structure transformation. A higher shear rate and particle volume fraction could reduce the transient time and the shear strength difference.

  2. Shear-affected depletion interaction

    NARCIS (Netherlands)

    July, C.; Kleshchanok, D.; Lang, P.R.

    2012-01-01

    We investigate the influence of flow fields on the strength of the depletion interaction caused by disc-shaped depletants. At low mass concentration of discs, it is possible to continuously decrease the depth of the depletion potential by increasing the applied shear rate until the depletion force i

  3. Grouted Connections with Shear Keys

    DEFF Research Database (Denmark)

    Pedersen, Ronnie; Jørgensen, M. B.; Damkilde, Lars

    2012-01-01

    This paper presents a finite element model in the software package ABAQUS in which a reliable analysis of grouted pile-to-sleeve connections with shear keys is the particular purpose. The model is calibrated to experimental results and a consistent set of input parameters is estimated so...

  4. Particle Tracking Velocimetry in Transitional Plane Couette Flow

    Science.gov (United States)

    Lüthi, B.; Holzner, B.; Kinzel, M.; Liberzon, A.; Tsinober, A.

    Plane Couette flow has the peculiar property that transition to turbulence occurs despite the fact that its laminar profile is linearly stable. For high enough Reynolds numbers small amplitude perturbations are enough to initiate the growth of turbulent spots. Such spots have been subject to investigation for a few decades, see e.g. [1, 2]. In addition, it has been observed that around transitional Reynolds numbers laminar and turbulent regions can co-exist if this Reynolds number is approached from the turbulent side, e.g., [3, 4]. For both cases, distinct interfaces divide the regimes between turbulent and non turbulent flow. It is our main interest to study the evolution of such interfaces similar to the work of [5] where the shear free case with inhomogeneous forcing by an oscillating grid has been investigated in detail.

  5. FRACTURE ANALYSIS OF A FUNCTIONALLY GRADED STRIP UNDER PLANE DEFORMATION

    Institute of Scientific and Technical Information of China (English)

    Cheng Zhanqi; Zhong Zheng

    2006-01-01

    In this paper the plane elasticity problem for a functionally graded strip containing a crack is considered. It is assumed that the reciprocal of the shear modulus is a linear function of the thickness-coordinate, while the Possion's ratio keeps constant. By utilizing the Fourier trans formation technique and the transfer matrix method, the mixed boundary problem is reduced to a system of singular integral equations that are solved numerically. The influences of the geometric parameters and the graded parameter on the stress intensity factors and the strain energy release rate are investigated. The numerical results show that the graded parameters, the thickness of the strip and the crack size have significant effects on the stress intensity factors and the strain energy release rate.

  6. Homotopy between plane Couette flow and Pipe flow

    Science.gov (United States)

    Nagata, Masato; Deguchi, Kengo

    2014-11-01

    In order to investigate symmetry connections between two canonical shear flows, i.e. plane Couette (PCF) and pipe flow (PF), which are linearly stable for all Reynolds numbers and therefore undergo subcritical transition, we take annular Poiseuille-Couette flow (APCF) as an intermediary Although PCF and PF are very different geometrically, APCF recovers PCF by taking the narrow gap limit, and also PF by taking the limit of vanishing inner cylinder where a homotopy of the basis functions from no-slip to regular conditions at the centre is considered. We show that the double-layered mirror-symmetric solutions in sliding Couette flow (APCF without axial pressure gradient) found by Deguchi & Nagata (2011) can be traced back to the mirror-symmetric solutions in PCF. Also we show that only the double-layered solution successfully reaches the PF limit, reproducing the mirror-symmetric solution in PF classified as M1 by Pringle & Kerswell (2007).

  7. Enhancement of thermal fluctuations in Plane Couette Flow

    Science.gov (United States)

    Ortiz de Zarate, Jose M.; Sengers, Jan V.

    2011-11-01

    Mode-coupling phenomena in systems outside equilibrium generically cause an enhancement of thermal fluctuations. These enhancements can be studied by Landau's fluctuating hydrodynamics. Here we present a detailed study for the case of plane Couette flow based on stochastically forced Orr-Sommerfeld and Squire equations. The forcing arises from random contributions to the stress tensor due to the stochastic nature of molecular collisions. This intrinsic stochastic forcing is then amplified by mode- coupling mechanisms associated with the shear flow. We discuss the different coupling mechanisms, the most important one being the direct coupling between fluctuations of the wall-normal velocity and vorticity. The most pronounced effect is amplification of wall-normal vorticity fluctuations with a spanwise modulation at dimensionless wave numbers q∥ around 1.5. Financial support: MICINN FIS2008/03801.

  8. National Aerospace Plane Integrated Fuselage/Cryotank Risk Reduction program

    Science.gov (United States)

    Dayton, K. E.

    1993-06-01

    The principal objectives and results of the National Aerospace Plane (NASP) Integrated Risk Reduction program are briefly reviewed. The program demonstrated the feasibility of manufacturing lightweight advanced composite materials for single-stage-to-orbit hypersonic flight vehicle applications. A series of combined load simulation tests (thermal, mechanical, and cryogenic) demonstrated proof of concept performance for an all unlined composite cryogenic fuel tank with flat end bulkheads and a high-temperature thin-shell advanced composite fuselage. Temperatures of the fuselage were as high as 1300 F, with 100 percent bending and shear loads applied to the tank while filled with 850 gallons of cryogenic fluid hydrogen (-425 F). Leak rates measured on and around the cryotank shell and bulkheads were well below acceptable levels.

  9. An introduction to finite projective planes

    CERN Document Server

    Albert, Abraham Adrian

    2015-01-01

    Geared toward both beginning and advanced undergraduate and graduate students, this self-contained treatment offers an elementary approach to finite projective planes. Following a review of the basics of projective geometry, the text examines finite planes, field planes, and coordinates in an arbitrary plane. Additional topics include central collineations and the little Desargues' property, the fundamental theorem, and examples of finite non-Desarguesian planes.Virtually no knowledge or sophistication on the part of the student is assumed, and every algebraic system that arises is defined and

  10. Linear and nonlinear studies of velocity shear driven three dimensional electron-magnetohydrodynamics instability

    Energy Technology Data Exchange (ETDEWEB)

    Gaur, Gurudatt; Das, Amita [Institute for Plasma Research, Bhat, Gandhinagar 382428 (India)

    2012-07-15

    The study of electron velocity shear driven instability in electron magnetohydrodynamics (EMHD) regime in three dimensions has been carried out. It is well known that the instability is non-local in the plane defined by the flow direction and that of the shear, which is the usual Kelvin-Helmholtz mode, often termed as the sausage mode in the context of EMHD. On the other hand, a local instability with perturbations in the plane defined by the shear and the magnetic field direction exists which is termed as kink mode. The interplay of these two modes for simple sheared flow case as well as that when an external magnetic field exists has been studied extensively in the present manuscript in both linear and nonlinear regimes. Finally, these instability processes have been investigated for the exact 2D dipole solutions of EMHD equations [M. B. Isichenko and A. N. Marnachev, Sov. Phys. JETP 66, 702 (1987)] for which the electron flow velocity is sheared. It has been shown that dipoles are very robust and stable against the sausage mode as the unstable wavelengths are typically longer than the dipole size. However, we observe that they do get destabilized by the local kink mode.

  11. Fragmentation and shear band formation by slow compression of brittle porous media

    Science.gov (United States)

    Pál, Gergő; Jánosi, Zoltán; Kun, Ferenc; Main, Ian G.

    2016-11-01

    Localized fragmentation is an important phenomenon associated with the formation of shear bands and faults in granular media. It can be studied by empirical observation, by laboratory experiment, or by numerical simulation. Here we investigate the spatial structure and statistics of fragmentation using discrete element simulations of the strain-controlled uniaxial compression of cylindrical samples of different finite size. As the system approaches failure, damage localizes in a narrow shear band or synthetic fault "gouge" containing a large number of poorly sorted noncohesive fragments on a broad bandwidth of scales, with properties similar to those of natural and experimental faults. We determine the position and orientation of the central fault plane, the width of the shear band, and the spatial and mass distribution of fragments. The relative width of the shear band decreases as a power law of the system size, and the probability distribution of the angle of the central fault plane converges to around 30 degrees, representing an internal coefficient of friction of 0.7 or so. The mass of fragments is power law distributed, with an exponent that does not depend on scale, and is near that inferred for experimental and natural fault gouges. The fragments are in general angular, with a clear self-affine geometry. The consistency of this model with experimental and field results confirms the critical roles of preexisting heterogeneity, elastic interactions, and finite system size to grain size ratio on the development of shear bands and faults in porous media.

  12. Chaotic and regular shear-induced orientational dynamics of nematic liquid crystals

    Science.gov (United States)

    Rienäcker, G.; Kröger, M.; Hess, S.

    2002-12-01

    Based on a relaxation equation for the alignment tensor characterizing the molecular orientation in liquid crystals under flow we present results for the full orientational dynamics of homogeneous liquid crystals in a shear flow. We extend the analysis of the symmetry-adapted states by Rienäcker and Hess (Physica A 267 (1999) 294), which invoke only 3 of the 5 components of the tensor to full alignment. The steady and transient states of reduced model are preserved in this more general description, except for log-rolling, which turns out to be unstable in the range of parameters considered. However, the states reported earlier are only stable within a certain range of the parameters and there is a variety of new, symmetry-breaking transient states with the director out of the shear plane, which partially coexist with the in-plane states. The new, out-of-plane states can be divided in two classes: simple periodic and complex orbits. The first class consists of a kayaking-tumbling and a kayaking-wagging state, where the projection of the director onto the shear plane describes a tumbling or wagging motion, respectively. The second class of states, which can be found only in a small parameter range, consists of a variety of either complicated periodic or irregular, chaotic orbits. Both an intermittency route and a period-doubling route to chaos are found. A link to the corresponding rheological properties is made.

  13. Thermodynamics of black plane solution

    CERN Document Server

    Rodrigues, Manuel E; Houndjo, Stéphane J M

    2012-01-01

    We obtain a new phantom black plane solution in 4D of the Einstein-Maxwell theory coupled with a cosmological constant. We analyse their basic properties and obtain the extensive and intensive thermodynamic variables, as well as the specific heat and the first law. Through the specific heat and the so-called geometric methods, we analyse in detail their thermodynamic properties, the extreme and phase transition limits, as well as the local and global stabilities of the system. The normal case is shown with an extreme limit and the phantom one with a phase transition only for null mass. The systems present local and global stabilities for certain values of the entropy density with respect to the electric charge, for the canonical and grand canonical ensembles.

  14. Thermodynamics of black plane solution

    Science.gov (United States)

    Rodrigues, Manuel E.; Jardim, Deborah F.; Houndjo, Stéphane J. M.; Myrzakulov, Ratbay

    2013-11-01

    We obtain a new phantom black plane solution in D of the Einstein-Maxwell theory coupled with a cosmological constant. We analyse their basic properties, as well as its causal structure, and obtain the extensive and intensive thermodynamic variables, as well as the specific heat and the first law. Through the specific heat and the so-called geometric methods, we analyse in detail their thermodynamic properties, the extreme and phase transition limits, as well as the local and global stabilities of the system. The normal case is shown with an extreme limit and the phantom one with a phase transition only for null mass, which is physically inaccessible. The systems present local and global stabilities for certain values of the entropy density with respect to the electric charge, for the canonical and grand canonical ensembles.

  15. On plane submerged laminar jets

    Science.gov (United States)

    Coenen, Wilfried; Sanchez, Antonio L.

    2016-11-01

    We address the laminar flow generated when a developed stream of liquid of kinematic viscosity ν flowing along channel of width 2 h discharges into an open space bounded by two symmetric plane walls departing from the channel rim with an angle α 1 . Attention is focused on values of the jet volume flux 2 Q such that the associated Reynolds number Re = Qh / ν is of order unity. The formulation requires specification of the boundary conditions far from the channel exit. If the flow is driven by the volume flux, then the far-field solution corresponds to Jeffery-Hamel self-similar flow. However, as noted by Fraenkel (1962), such solutions exist only for α potential flow driven by the jet entrainment, and a Falkner-Skan near-wall boundary layer. Numerical integrations of the Navier-Stokes equations are used to ascertain the existence of these different solutions.

  16. Electrical conductivity anisotropy of partially molten peridotite under shear deformation

    Science.gov (United States)

    Zhang, B.; Yoshino, T.; Yamazaki, D.; Manthilake, G. M.; Katsura, T.

    2013-12-01

    Recent ocean bottom magnetotelluric investigations have revealed a high-conductivity layer (HCL) with high anisotropy characterized by higher conductivity values in the direction parallel to the plate motion beneath the southern East Pacific Rise (Evans et al., 2005) and beneath the edge of the Cocos plate at the Middle America trench offshore of Nicaragua (Naif et al., 2013). These geophysical observations have been attributed to either hydration (water) of mantle minerals or the presence of partial melt. Currently, aligned partial melt has been regarded as the most preferable candidate for explaining the conductivity anisotropy because of the implausibility of proton conduction (Yoshino et al., 2006). In this study, we report development of the conductivity anisotropy between parallel and normal to shear direction on the shear plane in partial molten peridotite as a function of time and shear strain. Starting samples were pre-synthesized partial molten peridotite, showing homogeneous melt distribution. The partially molten peridotite samples were deformed in simple shear geometry at 1 GPa and 1723 K in a DIA-type apparatus with uniaxial deformation facility. Conductivity difference between parallel and normal to shear direction reached one order, which is equivalent to that observed beneath asthenosphere. In contrast, such anisotropic behavior was not found in the melt-free samples, suggesting that development of the conductivity anisotropy was generated under shear stress. Microstructure of the deformed partial molten peridotite shows partial melt tends to preferentially locate grain boundaries parallel to shear direction, and forms continuously thin melt layer sub-parallel to the shear direction, whereas apparently isolated distribution was observed on the section perpendicular to the shear direction. The resultant melt morphology can be approximated by tube like geometry parallel to the shear direction. This observation suggests that the development of

  17. Review of the Shearing Process for Sheet Steels and Its Effect on Sheared-Edge Stretching

    Science.gov (United States)

    Levy, B. S.; Van Tyne, C. J.

    2012-07-01

    Failure in sheared-edge stretching often limits the use of advanced high-strength steel sheets in automotive applications. The present study analyzes data in the literature from laboratory experiments on both the shearing process and the characteristics of sheared edges. Shearing produces a surface with regions of rollover, burnish, fracture, and burr. The effect of clearance and tensile strength on the shear face characteristics is quantified. Higher strength, lower ductility steels exhibit an increase in percent fracture region. The shearing process also creates a zone of deformation adjacent to the shear face called the shear-affected zone (SAZ). From an analysis of data in the literature, it is concluded that deformation in the SAZ is the dominant factor in controlling failure during sheared-edge stretching. The characteristics of the shear face are generally important for failures during sheared-edge stretching only as there is a correlation between the characteristics of the shear face and the characteristics of the SAZ. The effect of the shear burr on shear-edge stretching is also related to a correlation with the characteristics of the SAZ. In reviewing the literature, many shearing variables that could affect sheared-edge stretching limits are not identified or if identified, not quantified. It is likely that some of these variables could affect subsequent sheared-edge stretching limits.

  18. X-Point Reconnection from Shear Driving in Kinetic Simulations

    Science.gov (United States)

    Black, C.; Antiochos, S. K.; DeVore, C. R.; Germaschewski, K.; Bessho, N.; Karpen, J. T.

    2014-12-01

    The explosive energy release in solar eruptive phenomena such as CMEs/eruptive flares and coronal jets is believed to be due to magnetic reconnection. Magnetic free energy builds up slowly in the corona due to footpoint stressing by the photospheric motions. Along with the free energy, current sheets build up at coronal nulls, which eventually triggers fast reconnection and explosive energy release. This basic scenario has been modeled extensively by MHD simulations and applied to both CMEs/eruptive flares and jets, but the reconnection itself is well-known to be due to kinetic processes. Consequently, it is imperative that shear-driven X-point reconnection be modeled in a fully kinetic system so as to test and guide the MHD results. In MHD simulations, the application of a magnetic-field shear at the system boundary is a trivial matter, but this is definitely not the case for a kinetic system, because the electric currents need to be fully consistent with all the mass motions. We present the first results of reconnection in a 2D X-Point geometry due to a velocity shear driver perpendicular to the plane of reconnection. We compare the results to high-resolution MHD simulations and discuss the implications for coronal activity.

  19. On the Structure Orientation in Rotating and Sheared Homogeneous Turbulence

    Science.gov (United States)

    Aguirre, Joylene C.; Moreau, Adam F.; Jacobitz, Frank G.

    2016-11-01

    The results of direct numerical simulations are used to study the effect of rotation on the orientation of structures and the evolution of the turbulent kinetic energy in homogeneous sheared turbulence. Shear flows without rotation, with moderate rotation, and with strong rotation are considered and the rotation axis is either parallel or anti-parallel to the mean flow vorticity. In the case of moderate rotation, an anti-parallel configuration increases the growth rate of the turbulent kinetic energy, while a parallel configuration decreases the growth rate as compared to the flow without rotation. The orientation of turbulent structures present in the flows are characterized using the three-dimensional, two-point autocorrelation coefficient of velocity magnitude and vorticity magnitude. An ellipsoid is fitted to the surface defined by a constant autocorrelation coefficient value and the major and minor axes are used to determine the inclination angle of flow structures in the plane of shear. It was found that the inclination angle assumes a maximum value for the anti-parallel configuration with moderate rotation. Again, the inclination angle for the parallel configuration with moderate rotation is reduced as compared to the case without rotation. The smallest inclination angles are found for the strongly rotating cases. Hence, the inclination angle is directly related to the growth rate of the turbulent kinetic energy. University of San Diego Shiley-Marcos School of Engineering and McNair Scholars.

  20. Analytical Solution for Wave-Induced Response of Seabed with Variable Shear Modulus

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A plane strain analysis based on the generalized Biot's equation is utilized to investigate the wave-induced response of a poro-elastic seabed with variable shear modulus. By employing integral transform and Frobenius methods, the transient and steady solutions for the wave-induced pore water pressure, effective stresses and displacements are analytically derived in detail. Verification is available through the reduction to the simple case of homogeneous seabed. The numerical results indicate that the inclusion of variable shear modulus significantly affects the wave-induced seabed response.

  1. Analysis of a high intensity shear zone between overlapping fiber ends in a polymer matrix composite

    DEFF Research Database (Denmark)

    Lindgreen, Britta

    2008-01-01

    The formation of high intensity shear zones in a glass fiber reinforced thermoplast is studied numerically. The thermoplast is characterized by a finite strain elastic-viscoplastic constitutive relation and the calculations are carried out using a dynamic finite element program where plane strain...... conditions are assumed to prevail in the direction of the thickness. Different ratios of the elongation strain and the transverse strain are studied to consider the effect of different levels of stress triaxiality and the effect of these states on the shear zone development and emerging strain and stress...

  2. Hydrodynamic interaction between two vesicles in a linear shear flow: asymptotic study.

    Science.gov (United States)

    Gires, P Y; Danker, G; Misbah, C

    2012-07-01

    Interactions between two vesicles in an imposed linear shear flow are studied theoretically, in the limit of almost spherical vesicles, with a large intervesicle distance, in a strong flow, with a large inner to outer viscosity ratio. This allows to derive a system of ordinary equations describing the dynamics of the two vesicles. We provide an analytic expression for the interaction law. We find that when the vesicles are in the same shear plane, the hydrodynamic interaction leads to a repulsion. When they are not, the interaction may turn into attraction instead. The interaction law is discussed and analyzed as a function of relevant parameters.

  3. Plane Couette-Poiseuille flow past a homogeneous poroelastic layer

    Science.gov (United States)

    Alexiou, Terpsichori S.; Kapellos, George E.

    2013-07-01

    An analytical solution is presented for the problem of fully developed plane Couette-Poiseuille flow past a homogeneous, permeable poroelastic layer. Main novel feature of this work is that the compressibility, which is related to the action of the free-fluid pressure on the poroelastic layer, is taken into account. Therefore, the solid stress problem is two-dimensional, although the fluid flow problem remains one-dimensional in the limit of infinitesimal strain. The pressure-related compressibility affects strongly the distribution of the von Mises stress in the poroelastic layer by shifting the local maximum towards the high-pressure region of the channel. Furthermore, the established analytical solution is used to investigate some aspects of the mechanotransducing role of the endothelial surface layer. A compressible surface layer might serve as a "bumper'' by reducing the magnitude of the overall shearing force (viscous and elastic) acting on endothelial cells, as compared to the magnitude of the fluid shear force that would be exerted in its absence.

  4. Shear Thickening Behaviour of Composite Propellant Suspension under Oscillatory Shear

    Directory of Open Access Journals (Sweden)

    D. Singh

    2016-04-01

    Full Text Available Composite propellant suspensions consist of highly filled polymeric system wherein solid particles of different sizes and shapes are dispersed in a polymeric matrix. The rheological behaviour of a propellant suspension is characterised by viscoplasticity and shear rate and time dependant viscosity. The behaviour of composite propellant suspension has been studied under amplitude sweep test where tests were performed by continuously varying strain amplitude (strain in %, γ by keeping the frequency and temperature constant and results are plotted in terms of log γ (strain amplitude vs logGʹ and logGʺ (Storage modulus and loss modulus, respectively. It is clear from amplitude sweep test that dynamic moduli and complex viscosity show marked increase at critical strain amplitude after a plateau region, infering a shear thickening behaviour.

  5. Transiently Jammed State in Shear Thickening Suspensions under Shear

    Science.gov (United States)

    Mukhopadhyay, Shomeek; Allen, Benjamin; Brown, Eric

    2014-03-01

    We examine the response of a suspension of cornstarch and water under normal impact at controlled velocities. This is a model system to understand why a person can run on the surface of a discontinuous shear thickening fluid. Using simultaneous high-speed imaging of the top and bottom surfaces along with normal force measurements allows us to investigate whether the force response is a result of system spanning structures. We observe a shear thickening transition where above a critical velocity the normal force increases by orders of magnitude. In the high force regime the force response is displacement dependent like a solid rather than velocity dependent like a liquid. The stresses are on the order of 106 Pa which is enough to hold up a person's weight. In this regime imaging shows the existence of a solid like structure that extends to the bottom interface.

  6. Initiation and Propagation of Shear Bands in Antiplane Shear Deformation.

    Science.gov (United States)

    1984-03-01

    hypoelastic ), and they examined the differences between the uniform deformation field under rising load and the nonuniform field due to the imperfection...approach to the study of the criteria for the onset of shear localization in one dimensional models has been considered by some authors, including...to simulate the phenomenon of thermal softening due to adiabatic heating, a material model is selected which shows a local maximum in the dependence

  7. Generalized plane gravitational waves of non-symmetric unified field theories in plane symmetry

    Directory of Open Access Journals (Sweden)

    Sanjiv R. Bhoyar

    2012-12-01

    Full Text Available In this paper we investigated the plane wave solutions of both the weak and strong non-symmetric unified field equations of Einstein and Bonner in a generalized plane symmetric space-time in the sense of Taub [Ann. Math. 53, 472 (1951] for plane gravitational waves. We show that the plane wave solutions of Einstein and Bonner field equations exist in plane symmetry.

  8. Reduced thoracolumbar fascia shear strain in human chronic low back pain

    Science.gov (United States)

    2011-01-01

    Background The role played by the thoracolumbar fascia in chronic low back pain (LBP) is poorly understood. The thoracolumbar fascia is composed of dense connective tissue layers separated by layers of loose connective tissue that normally allow the dense layers to glide past one another during trunk motion. The goal of this study was to quantify shear plane motion within the thoracolumbar fascia using ultrasound elasticity imaging in human subjects with and without chronic low back pain (LBP). Methods We tested 121 human subjects, 50 without LBP and 71 with LBP of greater than 12 months duration. In each subject, an ultrasound cine-recording was acquired on the right and left sides of the back during passive trunk flexion using a motorized articulated table with the hinge point of the table at L4-5 and the ultrasound probe located longitudinally 2 cm lateral to the midline at the level of the L2-3 interspace. Tissue displacement within the thoracolumbar fascia was calculated using cross correlation techniques and shear strain was derived from this displacement data. Additional measures included standard range of motion and physical performance evaluations as well as ultrasound measurement of perimuscular connective tissue thickness and echogenicity. Results Thoracolumbar fascia shear strain was reduced in the LBP group compared with the No-LBP group (56.4% ± 3.1% vs. 70.2% ± 3.6% respectively, p fascia shear strain and the following variables: perimuscular connective tissue thickness (r = -0.45, p fascia shear strain was ~20% lower in human subjects with chronic low back pain. This reduction of shear plane motion may be due to abnormal trunk movement patterns and/or intrinsic connective tissue pathology. There appears to be some sex-related differences in thoracolumbar fascia shear strain that may also play a role in altered connective tissue function. PMID:21929806

  9. Developments in Plasticity Approach to Shear

    DEFF Research Database (Denmark)

    Hoang, Cao Linh; Nielsen, Mogens Peter

    1999-01-01

    The paper deals with plastic methods applied to shear design of reinforced concrete beams. Emphasis is put on the recently developed crack sliding model applicable to non-shear reinforced and lightly shear reinforced beams and slabs. The model, which is an upper bound plasticity approach, takes...

  10. Shear instability of a gyroid diblock copolymer

    DEFF Research Database (Denmark)

    Eskimergen, Rüya; Mortensen, Kell; Vigild, Martin Etchells

    2005-01-01

    -induced destabilization is discussed in relation to analogous observations on shear-induced order-to-order and disorder-to-order transitions observed in related block copolymer systems and in microemulsions. It is discussed whether these phenomena originate in shear-reduced fluctuations or shear-induced dislocations....

  11. Longitudinal shear resistance of composite slabs

    NARCIS (Netherlands)

    Schuurman, R.G.; Stark, J.W.B.

    1996-01-01

    Verification methods for longitudinal shear. currently in use, are empirical. This applies for both the m-k method as the Partial Shear Connection method. Parameters and mechanisms determining the behaviour of the shear connection in composite slabs are not directly considered in these methods. A

  12. Strain path effects on the development of shear bands during shear tests in aluminum alloy processed by ECAP

    Directory of Open Access Journals (Sweden)

    Cleber Granato de Faria

    2015-07-01

    Full Text Available ECAP (Equal Channel Angular Pressing involves the pressing of a prismatic specimen through two channels with the cross-section identical to that of the specimen and intercepting at a certain angle. The specimen undergoes shearing over a single plane but no dimensional changes, leading to a possible anisotropy in the mechanical properties of the processed specimen. In addition, multiple ECAP passes lead to a severe refinement of the material structure, which is a function of the angle between the channels and the rotation of the sample in successive passes (the so-called “processing route”. An analysis is presented of the mechanical and microstructural anisotropy along three orthogonal axes in an aluminum alloy specimen processed along three different processing routes. The mechanical properties were evaluated through shearing tests, and the stress–strain curves thus determined indicated that the mechanical behavior of the commercial purity aluminum after ECAP depends on the processing route. The analysis of the specimen surfaces after testing revealed the presence of shearing bands whose orientation also depended on the processing route.

  13. Steel-plate composite (SC) walls for safety related nuclear facilities: Design for in-plane forces and out-of-plane moments

    Energy Technology Data Exchange (ETDEWEB)

    Varma, Amit H., E-mail: ahvarma@purdue.edu [Bowen Laboratory, School of Civil Engineering, Purdue University, West Lafayette, IN (United States); Malushte, Sanjeev R., E-mail: smalusht@bechtel.com [Bechtel Power Corporation, Frederick, MD (United States); Sener, Kadir C., E-mail: ksener@purdue.edu [Bowen Laboratory, School of Civil Engineering, Purdue University, West Lafayette, IN (United States); Lai, Zhichao, E-mail: laiz@purdue.edu [Bowen Laboratory, School of Civil Engineering, Purdue University, West Lafayette, IN (United States)

    2014-04-01

    Steel-concrete (SC) composite walls being considered and used as an alternative to conventional reinforced concrete (RC) walls in safety-related nuclear facilities due to their construction economy and structural efficiency. However, there is a lack of standardized codes for SC structures, and design guidelines and approaches are still being developed. This paper presents the development and verification of: (a) mechanics based model, and (b) detailed nonlinear finite element model for predicting the behavior and failure of SC wall panels subjected to combinations of in-plane forces. The models are verified using existing test results, and the verified models are used to explore the behavior of SC walls subjected to combinations of in-plane forces and moments. The results from these investigations are used to develop an interaction surface in principle force (S{sub p1}–S{sub p2}) space that can be used to design or check the adequacy of SC wall panels. The interaction surface is easy to develop since it consists of straight line segments connecting anchor points defined by the SC wall section strengths in axial tension, in-plane shear, and compression. Both models and the interaction surface (for design) developed in this paper are recommended for future work. However, in order to use these approaches, the SC wall section should be detailed with adequate shear connector and tie bar strength and spacing to prevent non-ductile failure modes.

  14. Microstructures, deformation mechanisms and seismic properties of a Palaeoproterozoic shear zone: The Mertz shear zone, East-Antarctica

    Science.gov (United States)

    Lamarque, Gaëlle; Bascou, Jérôme; Maurice, Claire; Cottin, Jean-Yves; Riel, Nicolas; Ménot, René-Pierre

    2016-06-01

    The Mertz shear zone (MSZ) is a lithospheric scale structure that recorded mid-crustal deformation during the 1.7 Ga orogeny. We performed a microstructural and crystallographic preferred orientation (CPO) study of samples from both mylonites and tectonic boudins that constitute relics of the Terre Adélie Craton (TAC). The deformation is highly accommodated in the MSZ by anastomosed shear bands, which become more scattered elsewhere in the TAC. Most of the MSZ amphibolite-facies mylonites display similar CPO, thermal conditions, intensity of deformation and dominant shear strain. Preserved granulite-facies boudins show both coaxial and non-coaxial strains related to the previous 2.45 Ga event. This former deformation is more penetrative and less localized and shows a deformation gradient, later affected by a major phase of recrystallization during retrogression at 2.42 Ga. Both MSZ samples and granulite-facies tectonic boudins present microstructures that reflect a variety of deformation mechanisms associated with the rock creep that induce contrasted CPO of minerals (quartz, feldspar, biotite, amphibole and orthopyroxene). In particular, we highlight the development of an "uncommon" CPO in orthopyroxene from weakly deformed samples characterized by (010)-planes oriented parallel to the foliation plane, [001]-axes parallel to the stretching lineation and clustering of [100]-axes near the Y structural direction. Lastly, we computed the seismic properties of the amphibolite and granulite facies rocks in the MSZ area in order to evaluate the contribution of the deformed intermediate and lower continental crust to the seismic anisotropy recorded above the MSZ. Our results reveal that (i) the low content of amphibole and biotite in the rock formations of the TAC, and (ii) the interactions between the CPO of the different mineralogical phases, generate a seismically isotropic crust. Thus, the seismic anisotropy recorded by the seismic stations of the TAC, including the

  15. New experiment in Plane Poiseuille flow with zero mean advection velocity: observation of stationary turbulent spots

    Science.gov (United States)

    Klotz, Lukasz; Lemoult, Gregoire; Wesfreid, Jose Eduardo

    2015-11-01

    We describe a new experimental set-up which allows us to study the sub-critical transition to turbulence in a two dimensional shear flow (including plane Couette, plane Couette-Poiseuille and plane Poiseuille flows). Our facility is an extension of a classical plane Couette experiment, in which one uses a single closed loop of plastic belt to generate the opposite sign velocity at each wall of the test section. However, in our case, we use two independent closed loops of plastic belt, one at each wall of the test section. The speed of these belts may be controlled separately. That enables to set two different velocities (in value and direction) as a boundary conditions at each of two test section's walls. In addition the pressure gradient in streamwise direction can be controlled. In particular, the plane Poiseuille flow with zero mean advection velocity can be created. We characterize by PIV the basic flow for different configurations. For a plane Poiseuille flows as base flow, we were able to observe for the first time the nearly stationary turbulent spots in this flow, with structures of characteristic wavelength ~ the distance between the two plates.

  16. Finite Thin Cover on an Orthotropic Elastic Half Plane

    Directory of Open Access Journals (Sweden)

    Federico Oyedeji Falope

    2016-01-01

    Full Text Available The present work deals with the mechanical behaviour of thin films bonded to a homogeneous elastic orthotropic half plane under plain strain condition and infinitesimal strain. Both the film and semi-infinite substrate display linear elastic orthotropic behaviour. By assuming perfect adhesion between film and half plane together with membrane behaviour of the film, the compatibility condition between the coating and substrate leads to a singular integral equation with Cauchy kernel. Such an equation is straightforwardly solved by expanding the unknown interfacial stress in series of Chebyshev polynomials displaying square-root singularity at the film edges. This approach allows handling the singular behaviour of the shear stress and, in turn, reducing the problem to a linear algebraic system of infinite terms. Results are found for two loading cases, with particular reference to concentrated axial forces acting at the edges of the film. The corresponding mode II stress intensity factor has been assessed, thus providing the stress concentrations at both ends of the covering. Possible applications of the results here obtained range from MEMS, NEMS, and solar Silicon cell for energy harvesting to welded joint and building foundation.

  17. Punching shear capacity of reinforced concrete slabs with headed shear studs

    DEFF Research Database (Denmark)

    Hoang, Linh Cao; Pop, Anamaria

    2015-01-01

    Punching shear in slabs is analogous to shear in beams. Despite this similarity, current design codes provide distinctly different methods for the design of shear reinforcement in the two situations. For example, the Eurocode method for beam shear design is founded on the theory of rigid plasticity....... To design shear reinforcement in slabs, on the other hand, the engineer must settle for an empirical equation. The aim of the study reported is to demonstrate that it is possible in a simple manner to design shear reinforcement in slabs based on the same rigid-plasticity foundation as for beam shear design...

  18. Shear failure of granular materials

    Science.gov (United States)

    Degiuli, Eric; Balmforth, Neil; McElwaine, Jim; Schoof, Christian; Hewitt, Ian

    2012-02-01

    Connecting the macroscopic behavior of granular materials with the microstructure remains a great challenge. Recent work connects these scales with a discrete calculus [1]. In this work we generalize this formalism from monodisperse packings of disks to 2D assemblies of arbitrarily shaped grains. In particular, we derive Airy's expression for a symmetric, divergence-free stress tensor. Using these tools, we derive, from first-principles and in a mean-field approximation, the entropy of frictional force configurations in the Force Network Ensemble. As a macroscopic consequence of the Coulomb friction condition at contacts, we predict shear failure at a critical shear stress, in accordance with the Mohr-Coulomb failure condition well known in engineering. Results are compared with numerical simulations, and the dependence on the microscopic geometric configuration is discussed. [4pt] [1] E. DeGiuli & J. McElwaine, PRE 2011. doi: 10.1103/PhysRevE.84.041310

  19. Statistical Model of Extreme Shear

    DEFF Research Database (Denmark)

    Larsen, Gunner Chr.; Hansen, Kurt Schaldemose

    2004-01-01

    In order to continue cost-optimisation of modern large wind turbines, it is important to continously increase the knowledge on wind field parameters relevant to design loads. This paper presents a general statistical model that offers site-specific prediction of the probability density function...... by a model that, on a statistically consistent basis, describe the most likely spatial shape of an extreme wind shear event. Predictions from the model have been compared with results from an extreme value data analysis, based on a large number of high-sampled full-scale time series measurements...... are consistent, given the inevitabel uncertainties associated with model as well as with the extreme value data analysis. Keywords: Statistical model, extreme wind conditions, statistical analysis, turbulence, wind loading, statistical analysis, turbulence, wind loading, wind shear, wind turbines....

  20. Focal Plane Instrumentation of VERITAS

    CERN Document Server

    Nagai, T; Sleege, G; Petry, D

    2007-01-01

    VERITAS is a new atmospheric Cherenkov imaging telescope array to detect very high energy gamma rays above 100 GeV. The array is located in southern Arizona, USA, at an altitude of 1268m above sea level. The array consists of four 12-m telescopes of Davies-Cotton design and structurally resembling the Whipple 10-m telescope. The four focal plane instruments are equipped with high-resolution (499 pixels) fast photo-multiplier-tube (PMT) cameras covering a 3.5 degree field of view with 0.15 degree pixel separation. Light concentrators reduce the dead-space between PMTs to 25% and shield the PMTs from ambient light. The PMTs are connected to high-speed preamplifiers allowing operation at modest anode current and giving good single photoelectron peaks in situ. Electronics in the focus box provides real-time monitoring of the anode currents for each pixel and ambient environmental conditions. A charge injection subsystem installed in the focus box allows daytime testing of the trigger and data acquisition system b...

  1. Radioactivity in the galactic plane

    Science.gov (United States)

    Walraven, G. D.; Haymes, R. C.

    1976-01-01

    The paper reports the detection of a large concentration of interstellar radioactivity during balloon-altitude measurements of gamma-ray energy spectra in the band between 0.02 and 12.27 MeV from galactic and extragalactic sources. Enhanced counting rates were observed in three directions towards the plane of the Galaxy; a power-law energy spectrum is computed for one of these directions (designated B 10). A large statistical deviation from the power law in a 1.0-FWHM interval centered near 1.16 MeV is discussed, and the existence of a nuclear gamma-ray line at 1.15 MeV in B 10 is postulated. It is suggested that Ca-44, which emits gamma radiation at 1.156 MeV following the decay of radioactive Sc-44, is a likely candidate for this line, noting that Sc-44 arises from Ti-44 according to explosive models of supernova nucleosynthesis. The 1.16-MeV line flux inferred from the present data is shown to equal the predicted flux for a supernova at a distance of approximately 3 kpc and an age not exceeding about 100 years.

  2. A Collaborative Knowledge Plane for Autonomic Networks

    Science.gov (United States)

    Mbaye, Maïssa; Krief, Francine

    Autonomic networking aims to give network components self-managing capabilities. Several autonomic architectures have been proposed. Each of these architectures includes sort of a knowledge plane which is very important to mimic an autonomic behavior. Knowledge plane has a central role for self-functions by providing suitable knowledge to equipment and needs to learn new strategies for more accuracy.However, defining knowledge plane's architecture is still a challenge for researchers. Specially, defining the way cognitive supports interact each other in knowledge plane and implementing them. Decision making process depends on these interactions between reasoning and learning parts of knowledge plane. In this paper we propose a knowledge plane's architecture based on machine learning (inductive logic programming) paradigm and situated view to deal with distributed environment. This architecture is focused on two self-functions that include all other self-functions: self-adaptation and self-organization. Study cases are given and implemented.

  3. Haptic Edge Detection Through Shear

    Science.gov (United States)

    Platkiewicz, Jonathan; Lipson, Hod; Hayward, Vincent

    2016-01-01

    Most tactile sensors are based on the assumption that touch depends on measuring pressure. However, the pressure distribution at the surface of a tactile sensor cannot be acquired directly and must be inferred from the deformation field induced by the touched object in the sensor medium. Currently, there is no consensus as to which components of strain are most informative for tactile sensing. Here, we propose that shape-related tactile information is more suitably recovered from shear strain than normal strain. Based on a contact mechanics analysis, we demonstrate that the elastic behavior of a haptic probe provides a robust edge detection mechanism when shear strain is sensed. We used a jamming-based robot gripper as a tactile sensor to empirically validate that shear strain processing gives accurate edge information that is invariant to changes in pressure, as predicted by the contact mechanics study. This result has implications for the design of effective tactile sensors as well as for the understanding of the early somatosensory processing in mammals. PMID:27009331

  4. Elastic clearance change in axisymmetric shearing process

    Science.gov (United States)

    Yoshida, Yoshinori

    2016-10-01

    An axisymmetric shearing experiment is conducted for a sheet of low carbon steel and stainless steel. Elastic change in the clearance between punch and die is measured. The increase of the clearance in shearing is confirmed and the influence of sheared material's flow stress on the clearance change is shown. Finite element analysis (FEA) of shearing with Gurson-Tvergaard-Needlman model (GTN model) is conducted for shearing of the carbon steels with rigid tools as a numerical experiment. Burr height is predicted in the FEA and the result is compared with the experimental result. In addition, the influence of the clearance on stress state in the material is investigated.

  5. RF/Optical Demonstration: Focal Plane Assembly

    Science.gov (United States)

    Hoppe, D. J.; Chung, S.; Kovalik, J.; Gama, E.; Fernandez, M. M.

    2016-11-01

    In this article, we describe the second-generation focal plane optical assembly employed in the RF/optical demonstration at DSS-13. This assembly receives reflected light from the two mirror segments mounted on the RF primary. The focal plane assembly contains a fast steering mirror (FSM) to stabilize the focal plane spot, a pupil camera to aid in aligning the two segments, and several additional cameras for receiving the optical signal prior to as well as after the FSM loop.

  6. The effect of transverse shear on the postbuckling and growth characteristics of delaminations in composites

    Energy Technology Data Exchange (ETDEWEB)

    Ferrie, C.H.; Sheinman, I.; Kardomateas, G.A.

    1999-10-01

    A geometrically nonlinear formulation for the behavior of composite delaminated beams of arbitrary stacking sequence, and with the effects of transverse shear deformation included, is presented. The formulation is based on a first-order shear deformation kinematic model, which incorporates the bending-stretching coupling effect and also assumes an arbitrary initial imperfection. The nonlinear differential equations are solved by Newton's method using a finite-difference scheme. The growth of the delamination is also studied by applying the J-integral in order to derive a formula for the energy release rate, which includes transverse shear. Results are presented which illustrate the shear effect, especially with respect to the ratio of the in-plane extensional over shear modulus and with respect to the ratio of plate length over thickness. It is seen that transverse shear can affect largely the displacement profiles, rendering the structure more compliant, and can promote growth by increasing the energy release rate, but this latter effect is moderate and mainly noticeable only at the later stages in the postbuckling regime.

  7. Coupled fracture modes under anti-plane loading

    Directory of Open Access Journals (Sweden)

    Les P. Pook

    2016-07-01

    Full Text Available The linear elastic analysis of homogeneous, isotropic cracked bodies is a Twentieth Century development. It was recognised that the crack tip stress field is a singularity, but it was not until the introduction of the essentially two dimensional stress intensity factor concept in 1957 that widespread application to practical engineering problems became possible. The existence of three dimensional corner point effects in the vicinity of a corner point where a crack front intersects a free surface was investigated in the late 1970s: it was found that modes II and III cannot exist in isolation. The existence of one of these modes always induces the other. An approximate solution for corner point singularities by Bažant and Estenssoro explained some features of corner point effects but there were various paradoxes and inconsistencies. In an attempt to explain these a study was carried out on the coupled in-plane fracture mode induced by a nominal anti-plane (mode III loading applied to plates and discs weakened by a straight crack. The results derived from a large bulk of finite element models showed clearly that Bažant and Estenssoro’s analysis is incomplete. Some of the results of the study are summarised, together with some recent results for a disc under in-plane shear loading. On the basis of these results, and a mathematical argument, the results suggest that the stress field in the vicinity of a corner point is the sum of two singularities: one due to stress intensity factors and the other due to an as yet undetermined corner point singularity.

  8. On the effects of a dipping axis of symmetry on shear wave splitting measurements in a transversely isotropic medium

    NARCIS (Netherlands)

    Hilst, R.D. van der; Chevrot, Sébastien

    2003-01-01

    We derive the explicit expressions for the phase velocities and polarizations of quasi-shear waves propagating in a transversely isotropic medium. The normal to the plane defined by the phase normal and the symmetry axis gives the exact polarization of S₁, while the polarization of S₂ also depends o

  9. Quantitative test of the time dependent Gintzburg-Landau equation for sheared granular flow in two dimensions

    NARCIS (Netherlands)

    Saitoh, K.; Hayakawa, Hisao

    2013-01-01

    We examine the validity of the time-dependent Ginzburg-Landau equation of granular fluids for a plane shear flow under the Lees-Edwardsboundary condition derivedfrom a weakly nonlinear analysis through the comparison with the result of discrete element method.We verify quantitative agreements in the

  10. Large Format Uncooled Focal Plane Array Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Black Forest Engineering has identified innovative modifications in uncooled focal plane array (UFPA) architecture and processing that allows development of large...

  11. Comparison between SSF and Critical-Plane models to predict fatigue lives under multiaxial proportional load histories

    Directory of Open Access Journals (Sweden)

    Manuel de Freitas

    2016-10-01

    Full Text Available Materials can be classified as shear or tensile sensitive, depending on the main fatigue microcrack initiation process under multiaxial loadings. The nature of the initiating microcrack can be evaluated from a stress scale factor (SSF, which usually multiplies the hydrostatic or the normal stress term from the adopted multiaxial fatigue damage parameter. Low SSF values are associated with a shear-sensitive material, while a large SSF indicates that a tensile-based multiaxial fatigue damage model should be used instead. For tension-torsion histories, a recent published approach combines the shear and normal stress amplitudes using a SSF polynomial function that depends on the stress amplitude ratio (SAR between the shear and the normal components. Alternatively, critical-plane models calculate damage on the plane where damage is maximized, adopting a SSF value that is assumed constant for a given material, sometimes varying with the fatigue life (in cycles, but not with the SAR, the stress amplitude level, or the loading path shape. In this work, in-phase proportional tension-torsion tests in 42CrMo4 steel specimens for several values of the SAR are presented. The SSF approach is then compared with critical-plane models, based on their predicted fatigue lives and the observed values for these tension-torsion histories

  12. The formation of sporadic E layers by a vortical perturbation excited in a horizontal wind shear flow

    Directory of Open Access Journals (Sweden)

    G. G. Didebulidze

    2008-06-01

    Full Text Available The formation of the mid-latitude sporadic E layers (Es layers by an atmospheric vortical perturbation excited in a horizontal shear flow (horizontal wind with a horizontal linear shear is investigated. A three-dimensional atmospheric vortical perturbation (atmospheric shear waves, whose velocity vector is in the horizontal plane and has a vertical wavenumber kz≠0, can provide a vertical shear of the horizontal wind. The shear waves influence the vertical transport of heavy metallic ions and their convergence into thin and dense horizontal layers. The proposed mechanism takes into account the dynamical influence of the shear wave velocity in the horizontal wind on the vertical drift velocity of the ions. It also can explain the multi-layer structure of Es layers. The pattern of the multi-layer structure depends on the value of the shear-wave vertical wavelength, the ion-neutral collision frequency and the direction of the background horizontal wind. The modelling of formation of sporadic E layers with a single and a double peak is presented. Also, the importance of shear wave coupling with short-period atmospheric gravity waves (AGWs on the variations of sporadic E layer ion density is examined and discussed.

  13. Using a Numerical Model to Quantitatively Assess Dynamic Recrystallization as a Mechanism for He Enrichment in Mantle Shear Zones

    Science.gov (United States)

    Kaminski, K.; Mittelstaedt, E. L.; Warren, J. M.; Kurz, M. D.; Kumamoto, K.

    2015-12-01

    Recent studies of ductile peridotite shear zones in the Josephine Peridotite in SW Oregon find higher helium concentrations in whole rock samples located where total strain is greatest and recrystallized grain sizes are smallest. Based upon these results, previous workers suggest that dynamic recrystallization may lead to increased storage of He on grain boundaries. To assess the feasibility of this mechanism for enhanced He storage, we utilize a combined set of new and previous data from Shear Zone A (SZA) and B (SZB) of the Fresno Bench of the Josephine Peridotite to constrain a 1D numerical model of a ductile shear zone; the combined data set includes both He concentrations as well as measured total strain across the shear zone. Existing data within the region of highest strain (0 to ~2.5 m from the center of each shear zone) are sparse and, thus, we strategically sampled locations within this zone to maximize data resolution across a range of total strain. In each sample, we measure helium concentrations in unserpentinized harzburgite bulk rock using mass spectrometry. Analysis of the orientation of pyroxene foliation planes compared to shear planes provides an estimation of shear strain during deformation. Numerically, our model is discretized using finite differences and incorporates a non-linear, temperature-dependent viscosity, shear heating, and dynamic recrystallization. Here, we present our newly compiled collection of helium concentrations relative to total strain within SZA and SZB and measured grain sizes, which are used to constrain the modeled equilibrium grain size and quantitatively test dynamic recrystallization as a mechanism for concentrating He within peridotite shear zones.

  14. Steady shear rheometry of dissipative particle dynamics models of polymer fluids in reverse Poiseuille flow.

    Science.gov (United States)

    Fedosov, Dmitry A; Karniadakis, George Em; Caswell, Bruce

    2010-04-14

    Polymer fluids are modeled with dissipative particle dynamics (DPD) as undiluted bead-spring chains and their solutions. The models are assessed by investigating their steady shear-rate properties. Non-Newtonian viscosity and normal stress coefficients, for shear rates from the lower to the upper Newtonian regimes, are calculated from both plane Couette and plane Poiseuille flows. The latter is realized as reverse Poiseuille flow (RPF) generated from two Poiseuille flows driven by uniform body forces in opposite directions along two-halves of a computational domain. Periodic boundary conditions ensure the RPF wall velocity to be zero without density fluctuations. In overlapping shear-rate regimes the RPF properties are confirmed to be in good agreement with those calculated from plane Couette flow with Lees-Edwards periodic boundary conditions (LECs), the standard virtual rheometer for steady shear-rate properties. The concentration and the temperature dependence of the properties of the model fluids are shown to satisfy the principles of concentration and temperature superposition commonly employed in the empirical correlation of real polymer-fluid properties. The thermodynamic validity of the equation of state is found to be a crucial factor for the achievement of time-temperature superposition. With these models, RPF is demonstrated to be an accurate and convenient virtual rheometer for the acquisition of steady shear-rate rheological properties. It complements, confirms, and extends the results obtained with the standard LEC configuration, and it can be used with the output from other particle-based methods, including molecular dynamics, Brownian dynamics, smooth particle hydrodynamics, and the lattice Boltzmann method.

  15. Inhomogeneity Dislocation Interaction of Piezoelectric Materials Under Remote Non-uniform Shear & Electric Field

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The complex potentials method is used to develop a solution for a screw dislocation interacting with an elliptical piezoelectric inhomogeneity in piezoelectric materials under remote non-uniform antiplane shear and non-uniform inplane electric field. The theoretical analysis result is formulated via the conformal mapping and Laurent series expansion in the transformed plane by using complex variable method. The general expression of the complex variables is dirived explicitly in both the elliptical inhomogeneity and the surrounding matrix

  16. Two new ductile microscopic shear sense indicators from the Oman Mountains

    Science.gov (United States)

    Scharf, Andreas; Mattern, Frank; Pracejus, Bernhard

    2017-04-01

    The new shear sense indicators were observed in two different tectonic settings. The first one occurs in mylonitized Jurassic limestone on the northern flank of the Jebel Akhdar Dome (eastern Oman Mountains) and is associated with top-to-the-NNE extension. The second one was discovered in mylonitized plagiogranite (trondhjemite) with vertical to subvertical foliation and strike-slip deformation within harzburgite of the Semail Ophiolite in Wadi Fizh (northwestern Oman Mountains). The carbonate mylonite displays shear planes, in thin, flat and parallel laminations with a compositional aspect as there are alternations between pure calcite laminae and dark laminae of accumulated limestone impurities (iron compounds, clay). Despite the fact that the carbonate mylonite is associated with extension, the shear sense criterion is linked to top-to-the-NNE microthrusts, involving shortening of the dark laminae. The thrusts form an acute angle in relation to the lamination. Thrusting between segments of these, microthrusts created pull-aparts whose voids remained temporarily open cavities but were eventually filled with drusy calcite cement. The shear sense is revealed by (1) the shortening and related imbrication of the thrust laminae, (2) the pull-apart structures and (3) drag folds at either end of the microthrusts. The shear is also confirmed by independent ductile and brittle macroscopic shear sense criteria in the same outcrop, such as drag folds, Riedel shears and mineral steps. These new shear sense fabrics measure approximately 0.5mm in width and 1mm in length. The mylonitized granite contains large (2mm long axis) plagioclase porphyroclasts. We encountered a rotated plagioclase crystal whose twin lamellae have been dragged by the rotational motion during high-temperature conditions. Drag folds occur on either end of the lamellae/crystal. As a result an "S" shape is produced by counterclockwise rotation and sinistral shear, respectively. The observed shear sense is

  17. Low temperature rate coefficients for the reactions of 1CH2 with reactive and non-reactive species, and the implications for Titan's atmosphere

    Science.gov (United States)

    Douglas, Kevin; Slater, Eloise; Blitz, Mark; Plane, John; Heard, Dwayne; Seakins, Paul

    2016-04-01

    5 observed at 45±5 K. In addition to measuring total removal rates of 1CH2, the fraction of 1CH2 removed via electronic relaxation verses chemical reaction to products has also been investigated. Results for the reactive species ethane, ethene, and acetylene at 45±5 K, and for hydrogen and methane at 73±9 K indicate that following reactions with 1CH2, removal of 1CH2 is predominantly due to electronic relaxation (> 95 %) and not chemical reaction to products. This is in agreement with previous studies that show that with decreasing temperature, the fraction of reactive removal of 1CH2 to chemical products decreases while the fraction of removal by electronic relaxation increases[4][5]. These results indicate that 1CH2 formed in Titan's atmosphere will be rapidly relaxed to it's ground state via collisions with both reactive and non-reactive species, and thus will play a less significant role in the formation of larger hydrocarbons than previously thought. However for a full understanding of the implications of these results, the new measurements are to be included in a 1D model of Titan's atmosphere to determine the impact of the laboratory measurements on observation/model agreement. [1] K. Gannon et. al., J. Phys. Chem. A, (2010), 114, 9413 [2] E.H. Wilson, S.K. Atreya, J. Geophys. Res., (2004), 109, 6002 [3] M. Fulchignoni, Nature, (2005), 438, 785 [4] K. Gannon, Faraday Discuss., (2010), 147, 173 [5] K. Gannon, J. Phys. Chem. A, (2008), 112, 9575

  18. Stresses and Shear Fracture Zone of Jinshazhou Tunnel Surrounding Rock in Rich Water Region

    Institute of Scientific and Technical Information of China (English)

    ZHENG Jun-jie; LOU Xiao-ming

    2008-01-01

    Field evidence has shown that large-scale and unstable discontinuous planes in the rock mass surrounding tunnels in rich water region are probably generated after excavation. The tunnel surrounding rock was divided into three zones, including elastic zone, plastic damage zone and shear fracture zone fof assessing the stability of the tunnel surrounding rock. By local hydrogeology, the stresses of surrounding rock of Jinshazhou circular tunnel was analyzed and the stress solutions on the elastic and plastic damage zones were obtained by applying the theories of fluid-solid coupling and elasto-plastic damage mechanics. The shear fracture zone generated by joints was studied and its range was determined by using Mohr-Coulomb strength criterion. Finally, the correctness of the theoretical results was validated by comparing the scopes of shear fracture zones calculated in this paper with those from literature.

  19. Manipulating shear-induced non-equilibrium transitions in colloidal films by feedback control.

    Science.gov (United States)

    Vezirov, Tarlan A; Gerloff, Sascha; Klapp, Sabine H L

    2015-01-14

    Using Brownian Dynamics (BD) simulations we investigate non-equilibrium transitions of sheared colloidal films under controlled shear stress σxz. In our approach the shear rate [small gamma, Greek, dot above] is a dynamical variable, which relaxes on a time scale τc such that the instantaneous, configuration-dependent stress σxz(t) approaches a pre-imposed value. Investigating the dynamics under this "feedback-control" scheme we find unique behavior in regions where the flow curve σxz([small gamma, Greek, dot above]) of the uncontrolled system is monotonic. However, in non-monotonic regions our method allows to select between dynamical states characterized by different in-plane structure and viscosities. Indeed, the final state strongly depends on τc relative to an intrinsic relaxation time of the uncontrolled system. The critical values of τc are estimated on the basis of a simple model.

  20. Interactions of Shear Layer Vortices with the Trailing Corner in an Open Cavity Flow

    CERN Document Server

    Liu, Xiaofeng

    2011-01-01

    This fluid dynamics video provides sample experimental results focusing on the interactions of shear layer vortices with the trailing corner in a 2D open cavity shear layer. These interactions were investigated experimentally in a water tunnel at a Reynolds number of $4.0\\times 10^4$. Time-resolved particle image velocimetry (PIV) with an image sampling rate of 4500 frames per second was used to simultaneously measure the instantaneous velocity, material acceleration and pressure distribution. The latter was calculated by integrating the spatial distribution of in-plane components of the material acceleration. A large database of instantaneous realizations visualized the dynamic changes to the shear layer vortices, such as deformation and breakup as they impinged and climbed over the cavity trailing corner. These interactions cause time-dependent formation of a pressure maximum as the flow impinges on the forward facing surface of the trailing corner, and a minimum above the corner, where large local pressure...

  1. Collapse and coalescence of spherical voids subject to intense shearing: studied in full 3D

    DEFF Research Database (Denmark)

    Nielsen, Kim Lau; Dahl, Jonas; Tvergaard, Viggo

    2012-01-01

    for a range of initial material configurations and loading conditions. In addition, a direct comparison to corresponding 2D cell model predictions for circular cylindrical voids under plane strain shearing is presented. A quantitatively good agreement of the two model configurations (2D vs. 3D) is obtained......Micro-mechanical 2D cell model studies have revealed ductile failure during intense shearing to be governed by the interaction of neighbouring voids, which collapse to micro-cracks and continuously rotate and elongate until coalescence occurs. For a three-dimensional void structure, this implies...... shape, void orientation etc. The objective of this work is to expand the range of stress triaxiality usually faced in 3D cell model studies, such that intense shearing is covered, and to bring forward details on the porosity and void shape evolution. The overall material response is presented...

  2. Shear banding analysis of plastic models formulated for incompressible viscous flows

    Science.gov (United States)

    Lemiale, V.; Mühlhaus, H.-B.; Moresi, L.; Stafford, J.

    2008-12-01

    We investigate shear band orientations for a simple plastic formulation in the context of incompressible viscous flow. This type of material modelling has been introduced in literature to enable the numerical simulation of the deformation and failure of the lithosphere coupled with the mantle convection. In the present article, we develop a linear stability analysis to determine the admissible shear band orientations at the onset of bifurcation. We find that the so-called Roscoe angle and Coulomb angle are both admissible solutions. We present numerical simulations under plane strain conditions using the hybrid particle-in-cell finite element code Underworld. The results both in compressional and extensional stress conditions show that the variation of the numerical shear bands angle with respect to the internal friction angle follows closely the evolution of the Coulomb angle.

  3. Research on Failure Modes and Key Parameters of Corrugated Steel Shear Walls

    Directory of Open Access Journals (Sweden)

    Cao Qiang

    2016-01-01

    Full Text Available The corrugated steel plate shear wall is an effective and economical lateral load resisting system. And the thin steel plate is easy to buckle. And it is necessary to use much more thickness or ribs to prevent the buckle at out of plane direction, which is not economical or complicated to construct. A number of corrugated shear walls are analyzed by nonlinear static pushover analysis method. And failure modes, buckling, the ultimate capacity, and shear force-drift curves are studied. The results showed that the corrugated steel plate can be designed according to the failure modes, in order to have a desirable failure mode that the corrugated steel plate yield before buckling.

  4. Buckling analysis of thick isotropic plates by using exponential shear deformation theory

    Directory of Open Access Journals (Sweden)

    Sayyad A. S.

    2012-12-01

    Full Text Available In this paper, an exponential shear deformation theory is presented for the buckling analysis of thick isotropic plates subjected to uniaxial and biaxial in-plane forces. The theory accounts for a parabolic distribution of the transverse shear strains across the thickness, and satisfies the zero traction boundary conditions on the top and bottom surfaces of the plate without using shear correction factors. Governing equations and associated boundary conditions of the theory are obtained using the principle of virtual work. The simply supported thick isotropic square plates are considered for the detailed numerical studies. A closed form solutions for buckling analysis of square plates are obtained. Comparison studies are performed to verify the validity of the present results. The effects of aspect ratio on the critical buckling load of isotropic plates is investigated and discussed.

  5. Slipping and Rolling on an Inclined Plane

    Science.gov (United States)

    Aghamohammadi, Cina; Aghamohammadi, Amir

    2011-01-01

    In the first part of the paper, using a direct calculation two-dimensional motion of a particle sliding on an inclined plane is investigated for general values of friction coefficient ([mu]). A parametric equation for the trajectory of the particle is also obtained. In the second part of the paper, the motion of a sphere on the inclined plane is…

  6. The European Galactic Plane Surveys: EGAPS

    NARCIS (Netherlands)

    Groot, P.J.; Drew, J.; Greimel, R.; Gaensicke, B.; Knigge, C.; Irwin, M.; Mampaso, A.; Augusteijn, T.; Morales-Rueda, L.; Barlow, M.; Iphas, C.; Uvex, C.; Vphas, C.

    2006-01-01

    Introduction: The European Galactic Plane Surveys (EGAPS) will for the first time ever map the complete galactic plane (10x360 degrees) down to 21st magnitude in u', g', r', i' and H-alpha and partly in He I 5875. It will complete a database of ~1 billion objects. The aim of EGAPS is to study popula

  7. Fast & Furious focal-plane wavefront sensing

    NARCIS (Netherlands)

    Korkiakoski, V.A.; Keller, C.U.; Doelman, N.; Kenworthy, M.; Otten, G.; Verhaegen, M.H.G.

    2014-01-01

    We present two complementary algorithms suitable for using focal-plane measurements to control a wavefront corrector with an extremely high-spatial resolution. The algorithms use linear approximations to iteratively minimize the aberrations seen by the focal-plane camera. The first algorithm, Fast &

  8. Focal-plane sensor-processor chips

    CERN Document Server

    Zarándy, Ákos

    2011-01-01

    Focal-Plane Sensor-Processor Chips explores both the implementation and application of state-of-the-art vision chips. Presenting an overview of focal plane chip technology, the text discusses smart imagers and cellular wave computers, along with numerous examples of current vision chips.

  9. Shear zone junctions: Of zippers and freeways

    Science.gov (United States)

    Passchier, Cees W.; Platt, John P.

    2017-02-01

    Ductile shear zones are commonly treated as straight high-strain domains with uniform shear sense and characteristic curved foliation trails, bounded by non-deforming wall rock. Many shear zones, however, are branched, and if movement on such branches is contemporaneous, the resulting shape can be complicated and lead to unusual shear sense arrangement and foliation geometries in the wall rock. For Y-shaped shear zone triple junctions with three joining branches and transport direction at a high angle to the branchline, only eight basic types of junction are thought to be stable and to produce significant displacement. The simplest type, called freeway junctions, have similar shear sense in all three branches. The other types show joining or separating behaviour of shear zone branches similar to the action of a zipper. Such junctions may have shear zone branches that join to form a single branch (closing zipper junction), or a single shear zone that splits to form two branches, (opening zipper junction). All categories of shear zone junctions show characteristic foliation patterns and deflection of markers in the wall rock. Closing zipper junctions are unusual, since they form a non-active zone with opposite deflection of foliations in the wall rock known as an extraction fault or wake. Shear zipper junctions can form domains of overprinting shear sense along their flanks. A small and large field example are given from NE Spain and Eastern Anatolia. The geometry of more complex, 3D shear zone junctions with slip parallel and oblique to the branchline is briefly discussed.

  10. Effect of Eccentricity in Compound Droplets Subject to a Simple Shear Flow

    Science.gov (United States)

    Kim, Sangkyu; Dabiri, Sadegh

    2016-11-01

    A double emulsion, or a compound droplet, is a system where two liquids are separated by an immiscible third liquid, thereby forming an emulsion inside an emulsion. Compound drops benefit from this separation in applications such food sciences, microfluidics, pharmaceutical engineering, and polymer sciences. While the subjects of double emulsion preparations, deformations, and breakup mechanisms are well-explored, the time-evolution of non-concentric compound drops has received far less analytical or computational scrutiny. In this work, we present computational results using finite volume method with front-tracking approach for initially spherical and non-concentric compound drops in a shear flow. Our findings for low Reynolds number flows show that: 1. The surrounding shear flow to the outer drop induces a rotational velocity field inside it, causing the inner drop to tumble with the flow, 2. the tumbling motion persists in time, and acts to increase the eccentricity of the compound drop, and 3. the hemisection-plane to the outer drop that is aligned with the plane of the simple shear defines an unstable equilibrium for inner drop's center, and the inner drop continuously drifts away from that plane. This work suggests a means of favorably configuring compound drops suitable for breakups, and helps to understand their migration in channel flows.

  11. Magnetogenesis through Relativistic Velocity Shear

    Science.gov (United States)

    Miller, Evan

    Magnetic fields at all scales are prevalent in our universe. However, current cosmological models predict that initially the universe was bereft of large-scale fields. Standard magnetohydrodynamics (MHD) does not permit magnetogenesis; in the MHD Faraday's law, the change in magnetic field B depends on B itself. Thus if B is initially zero, it will remain zero for all time. A more accurate physical model is needed to explain the origins of the galactic-scale magnetic fields observed today. In this thesis, I explore two velocity-driven mechanisms for magnetogenesis in 2-fluid plasma. The first is a novel kinematic 'battery' arising from convection of vorticity. A coupling between thermal and plasma oscillations, this non-relativistic mechanism can operate in flows that are incompressible, quasi-neutral and barotropic. The second mechanism results from inclusion of thermal effects in relativistic shear flow instabilities. In such flows, parallel perturbations are ubiquitously unstable at small scales, with growth rates of order with the plasma frequency over a defined range of parameter-space. Of these two processes, instabilities seem far more likely to account for galactic magnetic fields. Stable kinematic effects will, at best, be comparable to an ideal Biermann battery, which is suspected to be orders of magnitude too weak to produce the observed galactic fields. On the other hand, instabilities grow until saturation is reached, a topic that has yet to be explored in detail on cosmological scales. In addition to investigating these magnetogenesis sources, I derive a general dispersion relation for three dimensional, warm, two species plasma with discontinuous shear flow. The mathematics of relativistic plasma, sheared-flow instability and the Biermann battery are also discussed.

  12. Large-scale instability in a sheared nonhelical turbulence: formation of vortical structures

    CERN Document Server

    Elperin, T; Kleeorin, N; Rogachevskii, I

    2007-01-01

    We study a large-scale instability in a sheared nonhelical turbulence that causes generation of large-scale vorticity. Three types of the background large-scale flows are considered, i.e., the Couette and Poiseuille flows in a small-scale homogeneous turbulence, and the "log-linear" velocity shear in an inhomogeneous turbulence. It is known that laminar plane Couette flow and antisymmetric mode of laminar plane Poiseuille flow are stable with respect to small perturbations for any Reynolds numbers. We demonstrate that in a small-scale turbulence under certain conditions the large-scale Couette and Poiseuille flows are unstable due to the large-scale instability. This instability causes formation of large-scale vortical structures stretched along the mean sheared velocity. The growth rate of the large-scale instability for the "log-linear" velocity shear is much larger than that for the Couette and Poiseuille background flows. We have found a turbulent analogue of the Tollmien-Schlichting waves in a small-scal...

  13. Hydrodynamic interactions between two equally sized spheres in viscoelastic fluids in shear flow.

    Science.gov (United States)

    Snijkers, Frank; Pasquino, Rossana; Vermant, Jan

    2013-05-14

    The effect of using a viscoelastic suspending medium on the in-plane hydrodynamic interaction between two equally sized spheres in shear flow is studied experimentally to understand flow-induced assembly behavior (i.e., string formation). A counterrotating device equipped with a Couette geometry is used together with quantitative videomicroscopy. To evaluate the effects of differences in rheological properties of the suspending media, fluids have been selected that highlight specific constitutive features. These include a reference Newtonian fluid (N), a constant-viscosity, high-elasticity Boger fluid (BF), a wormlike micellar surfactant solution with a single dominant relaxation time (WMS), and a broad spectrum shear-thinning elastic polymer solution (ST). As expected, the trajectories are symmetric in the Newtonian fluid. In the BF, the midpoints of the spheres are observed to remain in the same plane before and after the interaction, as in the Newtonian fluid, although the path lines are in this case no longer symmetric. Interactions in the ST and WMS are highly asymmetric. Two fundamentally different kinds of path lines are observed in the WMS and ST: reversing and open trajectories. The type of trajectory depends on the initial configuration of the spheres with respect to each other and on the shear rate. On the basis of the obtained results, shear-thinning of the viscosity seems to be the key rheological parameter that determines the overall nature of the interactions, rather than the relative magnitude of the normal stress differences.

  14. Elliptical Weighted HOLICs for Weak Lensing Shear Measurement. part1:Definitions and isotropic PSF correction

    CERN Document Server

    Okura, Yuki

    2010-01-01

    We develop a new method to estimate gravitational shear by adopting an elliptical weight function to measure background galaxy images. In doing so, we introduce a new concept of "zero plane" which is an imaginal source plane where shapes of all sources are perfect circles, and regard the intrinsic shear as the result of an imaginal lensing distortion. This makes the relation between the observed shear, the intrinsic shear and lensing distortion more simple and thus higher-order calculation more easy. The elliptical weight function allows us to measure the mutiplemoment of shape of background galaxies more precisely by weighting highly to brighter parts of image and moreover to reduce systematic error due to insufficient expansion of the weight function in the original approach of KSB. Point Spread Function(PSF) correction in E-HOLICs methods becomes more complicated than those in KSB methods. In this paper we studied isotropic PSF correction in detail. By adopting the lensing distortion as the ellipticity of ...

  15. Slipping and rolling on an inclined plane

    Energy Technology Data Exchange (ETDEWEB)

    Aghamohammadi, Cina [Department of Electrical Engineering, Sharif University of Technology, PO Box 11365-11155, Tehran (Iran, Islamic Republic of); Aghamohammadi, Amir, E-mail: mohamadi@alzahra.ac.ir [Department of Physics, Alzahra University, Tehran 19938-91176 (Iran, Islamic Republic of)

    2011-07-15

    In the first part of the paper, using a direct calculation two-dimensional motion of a particle sliding on an inclined plane is investigated for general values of friction coefficient ({mu}). A parametric equation for the trajectory of the particle is also obtained. In the second part of the paper, the motion of a sphere on the inclined plane is studied. It is shown that the evolution equation for the contact point of a sliding sphere is similar to that of a point particle sliding on an inclined plane whose friction coefficient is 7/2 {mu}. If {mu} > 2/7 tan {theta}, for any arbitrary initial velocity and angular velocity, the sphere will roll on the inclined plane after some finite time. In other cases, it will slip on the inclined plane. In the case of rolling, the centre of the sphere moves on a parabola. Finally the velocity and angular velocity of the sphere are exactly computed.

  16. Slipping and Rolling on an Inclined Plane

    CERN Document Server

    Aghamohammadi, Cina; 10.1088/0143-0807/32/4/017

    2011-01-01

    In the first part of the article using a direct calculation two-dimensional motion of a particle sliding on an inclined plane is investigated for general values of friction coefficient ($\\mu$). A parametric equation for the trajectory of the particle is also obtained. In the second part of the article the motion of a sphere on the inclined plane is studied. It is shown that the evolution equation for the contact point of a sliding sphere is similar to that of a point particle sliding on an inclined plane whose friction coefficient is $2/7}\\ \\mu$. If $\\mu> 2/7 \\tan\\theta$, for any arbitrary initial velocity and angular velocity the sphere will roll on the inclined plane after some finite time. In other cases, it will slip on the inclined plane. In the case of rolling center of the sphere moves on a parabola. Finally the velocity and angular velocity of the sphere are exactly computed.

  17. Statistical Model of Extreme Shear

    DEFF Research Database (Denmark)

    Hansen, Kurt Schaldemose; Larsen, Gunner Chr.

    2005-01-01

    In order to continue cost-optimisation of modern large wind turbines, it is important to continuously increase the knowledge of wind field parameters relevant to design loads. This paper presents a general statistical model that offers site-specific prediction of the probability density function...... by a model that, on a statistically consistent basis, describes the most likely spatial shape of an extreme wind shear event. Predictions from the model have been compared with results from an extreme value data analysis, based on a large number of full-scale measurements recorded with a high sampling rate...

  18. Reduced thoracolumbar fascia shear strain in human chronic low back pain

    Directory of Open Access Journals (Sweden)

    Konofagou Elisa E

    2011-09-01

    Full Text Available Abstract Background The role played by the thoracolumbar fascia in chronic low back pain (LBP is poorly understood. The thoracolumbar fascia is composed of dense connective tissue layers separated by layers of loose connective tissue that normally allow the dense layers to glide past one another during trunk motion. The goal of this study was to quantify shear plane motion within the thoracolumbar fascia using ultrasound elasticity imaging in human subjects with and without chronic low back pain (LBP. Methods We tested 121 human subjects, 50 without LBP and 71 with LBP of greater than 12 months duration. In each subject, an ultrasound cine-recording was acquired on the right and left sides of the back during passive trunk flexion using a motorized articulated table with the hinge point of the table at L4-5 and the ultrasound probe located longitudinally 2 cm lateral to the midline at the level of the L2-3 interspace. Tissue displacement within the thoracolumbar fascia was calculated using cross correlation techniques and shear strain was derived from this displacement data. Additional measures included standard range of motion and physical performance evaluations as well as ultrasound measurement of perimuscular connective tissue thickness and echogenicity. Results Thoracolumbar fascia shear strain was reduced in the LBP group compared with the No-LBP group (56.4% ± 3.1% vs. 70.2% ± 3.6% respectively, p Conclusion Thoracolumbar fascia shear strain was ~20% lower in human subjects with chronic low back pain. This reduction of shear plane motion may be due to abnormal trunk movement patterns and/or intrinsic connective tissue pathology. There appears to be some sex-related differences in thoracolumbar fascia shear strain that may also play a role in altered connective tissue function.

  19. Analysis of a Griffith crack at the interface of two piezoelectric materials under anti-plane loading

    Science.gov (United States)

    Gherrous, M.; Ferdjani, H.

    2016-11-01

    The main objective of this work is the contribution to the study of the piezoelectric structures which contain preexisting defect (crack). For that, we consider a Griffith crack located at the interface of two piezoelectric materials in a semi-infinite plane structure. The structure is subjected to an anti-plane shearing combined with an in-plane electric displacement. Using integral Fourier transforms, the equations of piezoelectricity are converted analytically to a system of singular integral equations. The singular integral equations are further reduced to a system of algebraic equations and solved numerically by using Chebyshev polynomials. The stress intensity factor and the electric displacement intensity factor are calculated and used for the determination of the energy release rate which will be taken as fracture criterion. At the end, numerical results are presented for various parameters of the problem; they are also presented for an infinite plane structure.

  20. Turbulent rotating plane Couette flow: Reynolds and rotation number dependency of flow structure and momentum transport

    Science.gov (United States)

    Kawata, Takuya; Alfredsson, P. Henrik

    2016-07-01

    Plane Couette flow under spanwise, anticyclonic system rotation [rotating plane Couette flow (RPCF)] is studied experimentally using stereoscopic particle image velocimetry for different Reynolds and rotation numbers in the fully turbulent regime. Similar to the laminar regime, the turbulent flow in RPCF is characterized by roll cells, however both instantaneous snapshots of the velocity field and space correlations show that the roll cell structure varies with the rotation number. All three velocity components are measured and both the mean flow and all four nonzero Reynolds stresses are obtained across the central parts of the channel. This also allows us to determine the wall shear stress from the viscous stress and the Reynolds stress in the center of the channel, and for low rotation rates the wall shear stress increases with increasing rotation rate as expected. The results show that zero absolute vorticity is established in the central parts of the channel of turbulent RPCF for high enough rotation rates, but also that the mean velocity profile for certain parameter ranges shows an S shape giving rise to a negative velocity gradient in the center of the channel. We find that from an analysis of the Reynolds stress transport equation using the present data there is a transport of the Reynolds shear stress towards the center of the channel, which may then result in a negative mean velocity gradient there.

  1. Mechanical picture of the linear transient growth of vortical perturbations in incompressible smooth shear flows

    Science.gov (United States)

    Chagelishvili, George; Hau, Jan-Niklas; Khujadze, George; Oberlack, Martin

    2016-08-01

    The linear dynamics of perturbations in smooth shear flows covers the transient exchange of energies between (1) the perturbations and the basic flow and (2) different perturbations modes. Canonically, the linear exchange of energies between the perturbations and the basic flow can be described in terms of the Orr and the lift-up mechanisms, correspondingly for two-dimensional (2D) and three-dimensional (3D) perturbations. In this paper the mechanical basis of the linear transient dynamics is introduced and analyzed for incompressible plane constant shear flows, where we consider the dynamics of virtual fluid particles in the framework of plane perturbations (i.e., perturbations with plane surfaces of constant phase) for the 2D and 3D case. It is shown that (1) the formation of a pressure perturbation field is the result of countermoving neighboring sets of incompressible fluid particles in the flow, (2) the keystone of the energy exchange mechanism between the basic flow and perturbations is the collision of fluid particles with the planes of constant pressure in accordance with the classical theory of elastic collision of particles with a rigid wall, making the pressure field the key player in this process, (3) the interplay of the collision process and the shear flow kinematics describes the transient growth of plane perturbations and captures the physics of the growth, and (4) the proposed mechanical picture allows us to reconstruct the linearized Euler equations in spectral space with a time-dependent shearwise wave number, the linearized Euler equations for Kelvin modes. This confirms the rigor of the presented analysis, which, moreover, yields a natural generalization of the proposed mechanical picture of the transient growth to the well-established linear phenomenon of vortex-wave-mode coupling.

  2. Microstructural description of shear-thickening suspensions

    Directory of Open Access Journals (Sweden)

    Singh Abhinendra

    2017-01-01

    Full Text Available Dynamic particle-scale numerical simulations are used to study the variation of microstructure with shear stress during shear thickening in dense non-Brownian suspensions. The microscale information is used to characterize the differences between the shear thickened (frictional and non-thickened (lubricated, frictionless states. Here, we focus on the force and contact networks and study the evolution of associated anisotropies with increase in shear stress. The force and contact networks are both more isotropic in the shear-thickened state than in non-thickened state. We also find that both force and structural anisotropies are rate independent for both low and high stress, while they are rate (or stress dependent for the intermediate stress range where the shear thickening occurs. This behavior is similar to the evolution of viscosity with increasing stress, showing a clear correlation between the microstructure and the macroscopic rheology.

  3. Shear dynamo problem: Quasilinear kinematic theory.

    Science.gov (United States)

    Sridhar, S; Subramanian, Kandaswamy

    2009-04-01

    Large-scale dynamo action due to turbulence in the presence of a linear shear flow is studied. Our treatment is quasilinear and kinematic but is nonperturbative in the shear strength. We derive the integrodifferential equation for the evolution of the mean magnetic field by systematic use of the shearing coordinate transformation and the Galilean invariance of the linear shear flow. For nonhelical turbulence the time evolution of the cross-shear components of the mean field does not depend on any other components excepting themselves. This is valid for any Galilean-invariant velocity field, independent of its dynamics. Hence the shear-current assisted dynamo is essentially absent, although large-scale nonhelical dynamo action is not ruled out.

  4. The Shear Dynamo: quasilinear kinematic theory

    CERN Document Server

    Sridhar, S

    2008-01-01

    Large--scale dynamo action due to turbulence in the presence of a linear shear flow is studied. Our treatment is quasilinear and kinematic but is non perturbative in the strength of the background shear. We derive expressions for the turbulent transport coefficients of the mean magnetic field, by systematic use of the shearing coordinate transformation and the Galilean invariance of the linear shear flow. We prove that, for non helical turbulence, the equation governing the time evolution of the cross shear component of the mean magnetic field is closed, in the sense that it is independent of the other two components. This result is valid for any Galilean--invariant velocity field, independent of its dynamics. Thus we find the shear--current assisted dynamo is essentially absent, although large--scale non helical dynamo action is not ruled out.

  5. PIV measurements of isothermal plane turbulent impinging jets at moderate Reynolds numbers

    Science.gov (United States)

    Khayrullina, A.; van Hooff, T.; Blocken, B.; van Heijst, G. J. F.

    2017-04-01

    This paper contains a detailed experimental analysis of an isothermal plane turbulent impinging jet (PTIJ) for two jet widths at moderate Reynolds numbers (7200-13,500) issued on a horizontal plane at fixed relative distances equal to 22.5 and 45 jet widths. The available literature on such flows is scarce. Previous studies on plane turbulent jets mainly focused on free jets, while most studies on impinging jets focused on the heat transfer between the jet and an impingement plane, disregarding jet development. The present study focuses on isothermal PTIJs at moderate Reynolds numbers characteristic of air curtains. Flow visualisations with fluorescent dye and 2D particle image velocimetry (PIV) measurements have been performed. A comparison is made with previous studies of isothermal free turbulent jets at moderate Reynolds numbers. Mean and instantaneous velocity and vorticity, turbulence intensity, and Reynolds shear stress are analysed. The jet issued from the nozzle with higher aspect ratio shows more intensive entrainment and a faster decay of the centreline velocity compared to the jet of lower aspect ratio for the same value of jet Reynolds number. The profiles of centreline and cross-jet velocity and turbulence intensity show that the PTIJs behave as a free plane turbulent jet until 70-75% of the total jet height. Alongside the information obtained on the jet dynamics, the data will be useful for the validation of numerical simulations.

  6. Shear wall ultimate drift limits

    Energy Technology Data Exchange (ETDEWEB)

    Duffey, T.A. [Duffy, (T.A.) Tijeras, NM (United States); Goldman, A. [Goldman, (A.), Sandia, Los Alamos, NM (United States); Farrar, C.R. [Los Alamos National Lab., NM (United States)

    1994-04-01

    Drift limits for reinforced-concrete shear walls are investigated by reviewing the open literature for appropriate experimental data. Drift values at ultimate are determined for walls with aspect ratios ranging up to a maximum of 3.53 and undergoing different types of lateral loading (cyclic static, monotonic static, and dynamic). Based on the geometry of actual nuclear power plant structures exclusive of containments and concerns regarding their response during seismic (i.e.,cyclic) loading, data are obtained from pertinent references for which the wall aspect ratio is less than or equal to approximately 1, and for which testing is cyclic in nature (typically displacement controlled). In particular, lateral deflections at ultimate load, and at points in the softening region beyond ultimate for which the load has dropped to 90, 80, 70, 60, and 50 percent of its ultimate value, are obtained and converted to drift information. The statistical nature of the data is also investigated. These data are shown to be lognormally distributed, and an analysis of variance is performed. The use of statistics to estimate Probability of Failure for a shear wall structure is illustrated.

  7. The Limits of Cosmic Shear

    CERN Document Server

    Kitching, Thomas D; Heavens, Alan F; Jimenez, Raul; McEwen, Jason D; Verde, Licia

    2016-01-01

    In this paper we discuss the commonly-used approximations for two-point cosmic shear statistics. We discuss the four most prominent assumptions in this statistic: the flat-sky, tomographic, Limber and configuration-space approximations, that the vast majority of cosmic shear results to date have used simultaneously. Of these approximations we find that the flat-sky approximation suppresses power by >1% on scales of l5% on scales l<100; in doing so we find an l-dependent factor that has been neglected in analyses to date. To investigate the impact of these approximations we reanalyse the CFHTLenS 2D correlation function results. When using all approximations we reproduce the result that measurements of the matter power spectrum amplitude are in tension with measurements from the CMB Planck data: where a conditional value of sigma8=0.789 +/- 0.015 is found from CFHTLenS and sigma8=0.830 +/- 0.015 from Planck. When we do not use the Limber and flat-sky approximations we find a conditional value of sigma8=0.80...

  8. Localized shear deformation during shear band propagation in titanium considering interactions among microstructures

    Institute of Scientific and Technical Information of China (English)

    王学滨; 杨梅; 于海军; 海龙; 潘一山

    2004-01-01

    Closed-form analytical solutions of plastic shear strain and relative plastic shear displacement during shear band propagation are proposed under dynamic loadings based on gradient-dependent plasticity considering the effect of microstructures due to heterogeneous texture of Ti. According to the differences in shear stress levels, Ti specimen is divided into three regions. residual region, strain-softening region and elastic region. Well-developed shear band is formed in the residual region and the relative plastic shear displacement no longer increases. In the normal and tangential directions, the plastic strain and the displacement are nonuniform in the strain-softening region.At the tip of shear band, the shear stress acting on the band is increased to shear strength from the elastic state and the shear localization just occurs. Prior to the tip, Ti remains elastic. At higher strain rates, the extent of plastic strain concentration is greater than that under static loading. Higher strain rate increases the relative plastic shear displacement. The present analytical solution for evolution or propagation of shear localization under nonuniform shear stress can better reproduce the observed localized characteristics for many kinds of ductile metals.

  9. Shear Wave Imaging of Breast Tissue by Color Doppler Shear Wave Elastography.

    Science.gov (United States)

    Yamakoshi, Yoshiki; Nakajima, Takahito; Kasahara, Toshihiro; Yamazaki, Mayuko; Koda, Ren; Sunaguchi, Naoki

    2017-02-01

    Shear wave elastography is a distinctive method to access the viscoelastic characteristic of the soft tissue that is difficult to obtain by other imaging modalities. This paper proposes a novel shear wave elastography [color Doppler shear wave imaging (CD SWI)] for breast tissue. Continuous shear wave is produced by a small lightweight actuator, which is attached to the tissue surface. Shear wave wavefront that propagates in tissue is reconstructed as a binary pattern that consists of zero and the maximum flow velocities on color flow image (CFI). Neither any modifications of the ultrasound color flow imaging instrument nor a high frame rate ultrasound imaging instrument is required to obtain the shear wave wavefront map. However, two conditions of shear wave displacement amplitude and shear wave frequency are needed to obtain the map. However, these conditions are not severe restrictions in breast imaging. This is because the minimum displacement amplitude is [Formula: see text] for an ultrasonic wave frequency of 12 MHz and the shear wave frequency is available from several frequencies suited for breast imaging. Fourier analysis along time axis suppresses clutter noise in CFI. A directional filter extracts shear wave, which propagates in the forward direction. Several maps, such as shear wave phase, velocity, and propagation maps, are reconstructed by CD SWI. The accuracy of shear wave velocity measurement is evaluated for homogeneous agar gel phantom by comparing with the acoustic radiation force impulse method. The experimental results for breast tissue are shown for a shear wave frequency of 296.6 Hz.

  10. Wind turbine wakes in forest and neutral plane wall boundary layer large-eddy simulations

    Science.gov (United States)

    Schröttle, Josef; Piotrowski, Zbigniew; Gerz, Thomas; Englberger, Antonia; Dörnbrack, Andreas

    2016-09-01

    Wind turbine wake flow characteristics are studied in a strongly sheared and turbulent forest boundary layer and a neutral plane wall boundary layer flow. The reference simulations without wind turbine yield similar results as earlier large-eddy simulations by Shaw and Schumann (1992) and Porte-Agel et al. (2000). To use the fields from the homogeneous turbulent boundary layers on the fly as inflow fields for the wind turbine wake simulations, a new and efficient methodology was developed for the multiscale geophysical flow solver EULAG. With this method fully developed turbulent flow fields can be achieved upstream of the wind turbine which are independent of the wake flow. The large-eddy simulations reproduce known boundary-layer statistics as mean wind profile, momentum flux profile, and eddy dissipation rate of the plane wall and the forest boundary layer. The wake velocity deficit is more asymmetric above the forest and recovers faster downstream compared to the velocity deficit in the plane wall boundary layer. This is due to the inflection point in the mean streamwise velocity profile with corresponding turbulent coherent structures of high turbulence intensity in the strong shear flow above the forest.

  11. Slip patterns and preferred dislocation boundary planes

    DEFF Research Database (Denmark)

    Winther, G.

    2003-01-01

    The planes of deformation induced extended planar dislocation boundaries are analysed in two different co-ordinate systems, namely the macroscopic system defined by the deformation axes and the crystallographic system given by the crystallographic lattice. The analysis covers single and polycryst......The planes of deformation induced extended planar dislocation boundaries are analysed in two different co-ordinate systems, namely the macroscopic system defined by the deformation axes and the crystallographic system given by the crystallographic lattice. The analysis covers single...... and polycrystals of fcc metals in three deformation modes (rolling, tension and torsion). In the macroscopic system, boundaries lie close to the macroscopically most stressed planes. In the crystallographic system, the boundary plane depends on the grain/crystal orientation. The boundary planes in both co......-ordinate systems are rationalised based on the slip. The more the slip is concentrated on a slip plane, the closer the boundaries lie to this. The macroscopic preference arises from the macroscopic directionality of the slip. The established relations are applied to (a) prediction of boundary planes from slip...

  12. ON WALL SHEAR STRESS OF ARTERY

    Institute of Scientific and Technical Information of China (English)

    Liu Zhao-rong; Liu Bao-yu; Qin Kai-rong

    2003-01-01

    In this paper, a method was proposed that the wall shear stress of artery could be determined by measuring the centerline axial velocity and radial motion of arterial wall simultaneously.The method is simple in application and can get higher precision when it is used to determine the shear stress of arterial wall in vivo.As an example, the shear stress distribution in periodic oscillatory flow of human carotid was calculated and discussed.The computed results show that the shear stress distribution at any given instant is almost uniform and will be zero at the centerline and tends to maximum at the vessel wall.

  13. Determination of arterial wall shear stress

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The arteries can remodel their structure and function to adapt themselves to the mechanical environment. In various factors that lead to vascular remodeling, the shear stress on the arterial wall induced by the blood flow is of great importance. However, there are many technique difficulties in measuring the wall shear stress directly at present. In this paper, through analyzing the pulsatile blood flow in arteries, a method has been proposed that can determine the wall shear stress quantitatively by measuring the velocity on the arterial axis, and that provides a necessary means to discuss the influence of arterial wall shear stress on vascular remodeling.

  14. Cyclic Shearing Deformation Behavior of Saturated Clays

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The apparatus for static and dynamic universal triaxial and torsional shear soil testing is employed to perform stress-controlled cyclic single-direction torsional shear tests and two-direction coupled shear tests under unconsolidated-undrained conditions. Through a series of tests on saturated clay, the effects of initial shear stress and stress reversal on the clay's strain-stress behavior are examined, and the behavior of pore water pressure is studied. The experimental results indicate that the patterns of stress-strain relations are distinctly influenced by the initial shear stress in the cyclic single-direction shear tests. When the initial shear stress is large and no stress reversal occurs, the predominant deformation behavior is characterized by an accumulative effect. When the initial shear stress is zero and symmetrical cyclic stress occurs, the predominant deformation behavior is characterized by a cyclic effect. The pore water pressure fluctuates around the confining pressure with the increase of cycle number. It seems that the fluctuating amplitude increases with the increase of the cyclic stress. But a buildup of pore water pressure does not occur. The deformations of clay samples under the complex initial and the cyclic coupled stress conditions include the normal deviatoric deformation and horizontal shear deformation, the average deformation and cyclic deformation. A general strain failure criterion taking into account these deformations is recommended and is proved more stable and suitable compared to the strain failure criteria currently used.

  15. Shear banding phenomena in a Laponite suspension

    CERN Document Server

    Ianni, F; Gentilini, S; Ruocco, G

    2007-01-01

    Shear localization in an aqueous clay suspension of Laponite is investigated through dynamic light scattering, which provides access both to the dynamics of the system (homodyne mode) and to the local velocity profile (heterodyne mode). When the shear bands form, a relaxation of the dynamics typical of a gel phase is observed in the unsheared band soon after flow stop, suggesting that an arrested dynamics is present during the shear localization regime. Periodic oscillations of the flow behavior, typical of a stick-slip phenomenon, are also observed when shear localization occurs. Both results are discussed in the light of various theoretical models for soft glassy materials.

  16. Origins of Shear Jamming for Frictional Grains

    Science.gov (United States)

    Wang, Dong; Zheng, Hu; Ren, Jie; Dijksman, Joshua; Bares, Jonathan; Behringer, Robert

    2016-11-01

    Granular systems have been shown to be able to behave like solids, under shear, even when their densities are below the critical packing fraction for frictionless isotropic jamming. To understand such a phenomena, called shear jamming, the question we address here is: how does shear bring a system from a unjammed state to a jammed state, where the coordination number, Z, is no less than 3, the isotropic jamming point for frictional grains? Since Z can be used to distinguish jammed states from unjammed ones, it is vital to understand how shear increases Z. We here propose a set of three particles in contact, denoted as a trimer, as the basic unit to characterize the deformation of the system. Trimers, stabilized by inter-grain friction, fail under a certain amount of shear and bend to make extra contacts to regain stability. By defining a projection operator of the opening angle of the trimer to the compression direction in the shear, O, we see a systematically linear decrease of this quantity with respect to shear strain, demonstrating the bending of trimers as expected. In addition, the average change of O from one shear step to the next shows a good collapse when plotted against Z, indicating a universal behavior in the process of shear jamming. We acknowledge support from NSF DMR1206351, NASA NNX15AD38G, the William M. Keck Foundation and a RT-MRSEC Fellowship.

  17. Dynamic shear deformation in high purity Fe

    Energy Technology Data Exchange (ETDEWEB)

    Cerreta, Ellen K [Los Alamos National Laboratory; Bingert, John F [Los Alamos National Laboratory; Trujillo, Carl P [Los Alamos National Laboratory; Lopez, Mike F [Los Alamos National Laboratory; Gray, George T [Los Alamos National Laboratory

    2009-01-01

    The forced shear test specimen, first developed by Meyer et al. [Meyer L. et al., Critical Adiabatic Shear Strength of Low Alloyed Steel Under Compressive Loading, Metallurgical Applications of Shock Wave and High Strain Rate Phenomena (Marcel Decker, 1986), 657; Hartmann K. et al., Metallurgical Effects on Impact Loaded Materials, Shock Waves and High Strain rate Phenomena in Metals (Plenum, 1981), 325-337.], has been utilized in a number of studies. While the geometry of this specimen does not allow for the microstructure to exactly define the location of shear band formation and the overall mechanical response of a specimen is highly sensitive to the geometry utilized, the forced shear specimen is useful for characterizing the influence of parameters such as strain rate, temperature, strain, and load on the microstructural evolution within a shear band. Additionally, many studies have utilized this geometry to advance the understanding of shear band development. In this study, by varying the geometry, specifically the ratio of the inner hole to the outer hat diameter, the dynamic shear localization response of high purity Fe was examined. Post mortem characterization was performed to quantify the width of the localizations and examine the microstructural and textural evolution of shear deformation in a bcc metal. Increased instability in mechanical response is strongly linked with development of enhanced intergranular misorientations, high angle boundaries, and classical shear textures characterized through orientation distribution functions.

  18. Novel shear mechanism in nanolayered composites

    Energy Technology Data Exchange (ETDEWEB)

    Mara, Nathan [Los Alamos National Laboratory; Bhattacharyya, Dhriti [Los Alamos National Laboratory; Hirth, John P [Los Alamos National Laboratory; Dickerson, Patricia O [Los Alamos National Laboratory; Misra, Amit [Los Alamos National Laboratory

    2009-01-01

    Recent studies have shown that two-phase nanocomposite materials with semicoherent interfaces exhibit enhanced strength, deformability, and radiation damage resistance. The remarkable behavior exhibited by these materials has been attributed to the atomistic structure of the bi-metal interface that results in interfaces with low shear strength and hence, strong barriers for slip transmission due to dislocation core spreading along the weak interfaces. In this work, the low interfacial shear strength of Cu/Nb nanoscale multilayers dictates a new mechanism for shear banding and strain softening during micropillar compression. Previous work investigating shear band formation in nanocrystalline materials has shown a connection between insufficient strain hardening and the onset of shear banding in Fe and Fe-10% Cu, but has also shown that hardening does not necessarily offset shear banding in Pd nanomaterials. Therefore, the mechanisms behind shear localization in nanocrystalline materials are not completely understood. Our findings, supported by molecular dynamics simulations, provide insight on the design of nanocomposites with tailored interface structures and geometry to obtain a combination of high strength and deformability. High strength is derived from the ability of the interfaces to trap dislocations through relative ease of interfacial shear, while deformability can be maximized by controlling the effects of loading geometry on shear band formation.

  19. Surface waves on arbitrary vertically-sheared currents

    CERN Document Server

    Smeltzer, Benjamin K

    2016-01-01

    We study dispersion properties of linear surface gravity waves propagating in an arbitrary direction atop a current profile of arbitrary depth-varying magnitude using a piecewise linear approximation, and develop a robust numerical framework for practical calculation. The method has been much used in the past in 2D, and we herein extend and apply it to 3D problems. Being valid for all wavelengths without loss of accuracy, the scheme is particularly well suited to solve problems involving Fourier transformations in the horizontal plane. We examine the group and phase velocities over different wavelength regimes and current profiles, highlighting characteristics due to the depth-variable vorticity. We show an example application to ship waves on an arbitrary current profile, and demonstrate qualitative differences in the wake patterns between a concave down profile when compared to a constant shear profile with equal depth-averaged vorticity. New insight is given concerning the nature of extra spurious solution...

  20. GodunovSPH with shear viscosity : implementation and tests

    CERN Document Server

    Cha, Seung-Hoon

    2016-01-01

    The acceleration and energy dissipation terms due to the shear viscosity have been implemented and tested in GodunovSPH. The double summation method has been employed to avoid the well known numerical noise of the second derivative in particle based codes. The plane Couette flow with various initial and boundary conditions have been used as tests, and the numerical and analytical results show a good agreement. Not only the viscosity--only calculation, but the full hydrodynamics simulations have been performed, and they show expected results as well. The very low kinematic viscosity simulations show a turbulent pattern when the Reynolds number exceeds $\\sim$$10^2$. The critical value of the Reynolds number at the transition point of the laminar and turbulent flows coincides with the previous works approximately. A smoothed dynamic viscosity has been suggested to describe the individual kinematic viscosity of particles. The infinitely extended Couette flow which has two layers of different viscosities has been ...

  1. Transverse shear effect in a circumferentially cracked cylindrical shell

    Science.gov (United States)

    Delale, F.; Erdogan, F.

    1979-01-01

    The objectives of the paper are to solve the problem of a circumferentially-cracked cylindrical shell by taking into account the effect of transverse shear, and to obtain the stress intensity factors for the bending moment as well as the membrane force as the external load. The formulation of the problem is given for a specially orthotropic material within the framework of a linearized shallow shell theory. The particular theory used permits the consideration of all five boundary conditions as to moment and stress resultants on the crack surface. The effect of Poisson's ratio on the stress intensity factors and the nature of the out-of-plane displacement along the edges of the crack, i.e., bulging, are also studied.

  2. A new energy transfer model for turbulent free shear flow

    Science.gov (United States)

    Liou, William W.-W.

    1992-01-01

    A new model for the energy transfer mechanism in the large-scale turbulent kinetic energy equation is proposed. An estimate of the characteristic length scale of the energy containing large structures is obtained from the wavelength associated with the structures predicted by a weakly nonlinear analysis for turbulent free shear flows. With the inclusion of the proposed energy transfer model, the weakly nonlinear wave models for the turbulent large-scale structures are self-contained and are likely to be independent flow geometries. The model is tested against a plane mixing layer. Reasonably good agreement is achieved. Finally, it is shown by using the Liapunov function method, the balance between the production and the drainage of the kinetic energy of the turbulent large-scale structures is asymptotically stable as their amplitude saturates. The saturation of the wave amplitude provides an alternative indicator for flow self-similarity.

  3. Optimal penetration landing trajectories in the presence of wind shear

    Science.gov (United States)

    Miele, A.; Wang, T.; Melvin, W. W.; Wang, H.

    1988-01-01

    Aircraft penetration landing in the presence of strong-to-severe wind shear is investigated analytically. The optimal-control problem for vertical-plane trajectories is considered, using angle of attack as one control parameter with either (1) a power setting (PS) which remains constant at its preshear value, (2) a PS which increases to its maximum value, or (3) a PS which is controlled (as the second parameter). The problem formulation is explained in detail, and numerical results obtained with the primal sequential gradient-restoration algorithm of Miele and Wang (1986) are presented in extensive tables and graphs. It is found that the touchdown requirements can only be satisfied by optimal trajectories using scheme (1) (but only at low altitudes) or scheme (3); the characteristics of the latter trajectories are explored.

  4. Influence of mandibular fixation method on stability of the maxillary occlusal plane after occlusal plane alteration.

    Science.gov (United States)

    Yosano, Akira; Katakura, Akira; Takaki, Takashi; Shibahara, Takahiko

    2009-05-01

    In this study, we investigated how method of mandibular fixation influenced longterm postoperative stability of the maxilla in Class III cases. In particular, we investigated change in the maxillary occlusal plane after Occlusal Plane Alteration. Therefore, we focused on change in the palatal plane to evaluate stability of the maxillary occlusal plane, as the position of the palatal plane affects the maxillary occlusal plane. This study included 16 patients diagnosed with mandibular protrusion. Alteration of the occlusal plane was achieved by clockwise rotation of the maxilla by Le Fort I osteotomy and mandibular setback was performed by bilateral sagittal split ramus osteotomy. We analyzed and examined lateral cephalometric radiographs taken at 1 month, 3 months, 6 months, and 1 year after surgery. Stability achieved by two methods of mandibular fixation was compared. In one group of patients (group S) titanium screws were used, and in the other group (group P) titanium-locking mini-plates were used. No significant displacement was recognized in group S, whereas an approximately 0.7mm upward vertical displacement was recognized in the anterior nasal spine in group P. As a result, not only the angle of the palatal plane and S-N plane, but also occlusal plane angle in group P showed a greater decrease than that in group S. The results suggest that fixing the mandible with screws yielded greater stability of the maxilla and maxillary occlusal plane than fixing the mandible with titanium plates.

  5. On the Construction of Mohr Stress Circle and a Graphic Method in Representing the Stress Components on Different Oblique Planes

    Institute of Scientific and Technical Information of China (English)

    Zhubin He; Z. R. Wang; Kunpeng Kang

    2004-01-01

    The Mohr stress circle for three-dimensional stress is usually determined by equations,which is lack of intuitionistic meanings and difficult to understand. In this paper, the construction of Mohr stress circle is illustrated directly by numerical method. The shortcoming of Mohr stress circle in representing the stress components on different oblique planes for three-dimensional stress is analyzed. A three-dimensional figure is given to describe the variation of normal and shear stress on different oblique planes at one point for the first time.

  6. Elliptically Weighted HOLICs for Weak-lensing Shear Measurement. I. Definitions and Isotropic Point-spread Function Correction

    Science.gov (United States)

    Okura, Yuki; Futamase, Toshifumi

    2011-03-01

    We develop a new method of estimating gravitational shear by adopting an elliptical weight function to measure background galaxy images. In doing so, we introduce the new concept of "zero plane," which is an imaginary source plane where shapes of all sources are perfect circles, and regard the intrinsic shear as the result of an imaginary lensing distortion. This makes the relation between the observed shear, intrinsic shear, and lensing distortion much simpler, and thus higher-order calculations are easier. The elliptical weight function allows us to measure the multipole moments of the shapes of background galaxies more precisely by weighting brighter parts of the image highly, and to reduce systematic error due to insufficient expansion of the weight function in the original approach of Kaiser et al. (KSB). Point-spread function (PSF) correction in the elliptically weighted higher-order lensing image characteristics (E-HOLICs) method becomes more complicated than in the KSB method. In this paper, we study isotropic PSF correction in detail. By adopting the lensing distortion as the ellipticity of the weight function, we are able to show that the shear estimation in the E-HOLICs method reduces to solve a polynomial in the absolute magnitude of the distortion. We compare the systematic errors between our approach and that of KSB using the Shear Testing Programme 2 simulation. It is confirmed that the KSB method overestimates the input shear for images with large ellipticities, and E-HOLICs correctly estimates the input shear even for such images. Anisotropic PSF correction and analysis of real data will be presented in a forthcoming paper.

  7. Streptococcus anginosus infections: crossing tissue planes.

    Science.gov (United States)

    Sunwoo, Bernie Y; Miller, Wallace T

    2014-10-01

    Streptococcus anginosus has long been recognized to cause invasive pyogenic infections. This holds true for thoracic infections where S. anginosus has a propensity for abscess and empyema formation. Early diagnosis is important given the significant morbidity and mortality associated with thoracic S. anginosus infections. Yet, distinguishing thoracic S. anginosus clinically is difficult. We present three cases of thoracic S. anginosus that demonstrated radiographic extension across tissue planes, including the interlobar fissure, diaphragm, and chest wall. Few infectious etiologies are known to cross tissue planes. Accordingly, we propose S. anginosus be considered among the differential diagnosis of potential infectious etiologies causing radiographic extension across tissue planes.

  8. Rail Shear and Short Beam Shear Properties of Various 3-Dimensional (3-D) Woven Composites

    Science.gov (United States)

    2016-01-01

    ARL-TR-7576 ● JAN 2016 US Army Research Laboratory Rail Shear and Short Beam Shear Properties of Various 3 - Dimensional ( 3 -D...2016 US Army Research Laboratory Rail Shear and Short Beam Shear Properties of Various 3 - Dimensional ( 3 -D) Woven Composites by Mark...Properties of Various 3 - Dimensional Woven Composites 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Mark Pankow

  9. Two-state shear diagrams for complex fluids in shear flow

    OpenAIRE

    1999-01-01

    The possible "phase diagrams'' for shear-induced phase transitions between two phases are collected. We consider shear-thickening and shear-thinning fluids, under conditions of both common strain rate and common stress in the two phases, and present the four fundamental shear stress vs. strain rate curves and discuss their concentration dependence. We outline how to construct more complicated phase diagrams, discuss in which class various experimental systems fall, and sketch how to reconstru...

  10. Numerical analysis of the angular motion of a neutrally buoyant spheroid in shear flow at small Reynolds numbers

    Science.gov (United States)

    Rosén, T.; Einarsson, J.; Nordmark, A.; Aidun, C. K.; Lundell, F.; Mehlig, B.

    2015-12-01

    We numerically analyze the rotation of a neutrally buoyant spheroid in a shear flow at small shear Reynolds number. Using direct numerical stability analysis of the coupled nonlinear particle-flow problem, we compute the linear stability of the log-rolling orbit at small shear Reynolds number Rea. As Rea→0 and as the box size of the system tends to infinity, we find good agreement between the numerical results and earlier analytical predictions valid to linear order in Rea for the case of an unbounded shear. The numerical stability analysis indicates that there are substantial finite-size corrections to the analytical results obtained for the unbounded system. We also compare the analytical results to results of lattice Boltzmann simulations to analyze the stability of the tumbling orbit at shear Reynolds numbers of order unity. Theory for an unbounded system at infinitesimal shear Reynolds number predicts a bifurcation of the tumbling orbit at aspect ratio λc≈0.137 below which tumbling is stable (as well as log rolling). The simulation results show a bifurcation line in the λ -Rea plane that reaches λ ≈0.1275 at the smallest shear Reynolds number (Rea=1 ) at which we could simulate with the lattice Boltzmann code, in qualitative agreement with the analytical results.

  11. Assembly of vorticity-aligned hard-sphere colloidal strings in a simple shear flow

    KAUST Repository

    Cheng, X.

    2011-12-23

    Colloidal suspensions self-assemble into equilibrium structures ranging from face- and body-centered cubic crystals to binary ionic crystals, and even kagome lattices. When driven out of equilibrium by hydrodynamic interactions, even more diverse structures can be accessed. However, mechanisms underlying out-of-equilibrium assembly are much less understood, though such processes are clearly relevant in many natural and industrial systems. Even in the simple case of hard-sphere colloidal particles under shear, there are conflicting predictions about whether particles link up into string-like structures along the shear flow direction. Here, using confocal microscopy, we measure the shear-induced suspension structure. Surprisingly, rather than flow-aligned strings, we observe log-rolling strings of particles normal to the plane of shear. By employing Stokesian dynamics simulations, we address the mechanism leading to this out-of-equilibrium structure and show that it emerges from a delicate balance between hydrodynamic and interparticle interactions. These results demonstrate a method for assembling large-scale particle structures using shear flows.

  12. An octahedral shear strain-based measure of SNR for 3D MR elastography

    Energy Technology Data Exchange (ETDEWEB)

    McGarry, M D J; Perrinez, P R; Pattison, A J; Weaver, J B; Paulsen, K D [Thayer School of Engineering, Dartmouth College, Hanover, NH 03755 (United States); Van Houten, E E W, E-mail: matthew.d.mcgarry@dartmouth.edu [Department of Mechanical Engineering, University of Canterbury, Christchurch (New Zealand)

    2011-07-07

    A signal-to-noise ratio (SNR) measure based on the octahedral shear strain (the maximum shear strain in any plane for a 3D state of strain) is presented for magnetic resonance elastography (MRE), where motion-based SNR measures are commonly used. The shear strain, {gamma}, is directly related to the shear modulus, {mu}, through the definition of shear stress, {tau} = {mu}{gamma}. Therefore, noise in the strain is the important factor in determining the quality of motion data, rather than the noise in the motion. Motion and strain SNR measures were found to be correlated for MRE of gelatin phantoms and the human breast. Analysis of the stiffness distributions of phantoms reconstructed from the measured motion data revealed a threshold for both strain and motion SNR where MRE stiffness estimates match independent mechanical testing. MRE of the feline brain showed significantly less correlation between the two SNR measures. The strain SNR measure had a threshold above which the reconstructed stiffness values were consistent between cases, whereas the motion SNR measure did not provide a useful threshold, primarily due to rigid body motion effects. (note)

  13. The role of shear and tensile failure in dynamically triggered landslides

    Science.gov (United States)

    Gipprich, T.L.; Snieder, R.K.; Jibson, R.W.; Kimman, W.

    2008-01-01

    Dynamic stresses generated by earthquakes can trigger landslides. Current methods of landslide analysis such as pseudo-static analysis and Newmark's method focus on the effects of earthquake accelerations on the landslide mass to characterize dynamic landslide behaviour. One limitation of these methods is their use Mohr-Coulomb failure criteria, which only accounts for shear failure, but the role of tensile failure is not accounted for. We develop a limit-equilibrium model to investigate the dynamic stresses generated by a given ground motion due to a plane wave and use this model to assess the role of shear and tensile failure in the initiation of slope instability. We do so by incorporating a modified Griffith failure envelope, which combines shear and tensile failure into a single criterion. Tests of dynamic stresses in both homogeneous and layered slopes demonstrate that two modes of failure exist, tensile failure in the uppermost meters of a slope and shear failure at greater depth. Further, we derive equations that express the dynamic stress in the near-surface in the acceleration measured at the surface. These equations are used to approximately define the depth range for each mechanism of failure. The depths at which these failure mechanisms occur suggest that shear and tensile failure might collaborate in generating slope failure. ?? 2007 The Authors Journal compilation ?? 2007 RAS.

  14. Experimental evidence for both progressive and simultaneous shear during quasistatic compression of a bulk metallic glass

    Science.gov (United States)

    Wright, Wendelin J.; Liu, Yun; Gu, Xiaojun; Van Ness, Katherine D.; Robare, Steven L.; Liu, Xin; Antonaglia, James; LeBlanc, Michael; Uhl, Jonathan T.; Hufnagel, Todd C.; Dahmen, Karin A.

    2016-02-01

    Two distinct types of slip events occur during serrated plastic flow of bulk metallic glasses. These events are distinguished not only by their size but also by distinct stress drop rate profiles. Small stress drop serrations have fluctuating stress drop rates (with maximum stress drop rates ranging from 0.3-1 GPa/s), indicating progressive or intermittent propagation of a shear band. The large stress drop serrations are characterized by sharply peaked stress drop rate profiles (with maximum stress drop rates of 1-100 GPa/s). The propagation of a large slip is preceded by a slowly rising stress drop rate that is presumably due to the percolation of slipping weak spots prior to the initiation of shear over the entire shear plane. The onset of the rapid shear event is accompanied by a burst of acoustic emission. These large slips correspond to simultaneous shear with uniform sliding as confirmed by direct high-speed imaging and image correlation. Both small and large slip events occur throughout plastic deformation. The significant differences between these two types require that they be carefully distinguished in both modeling and experimental efforts.

  15. Thermal conductivity of graphene nanoribbons under shear deformation: A molecular dynamics simulation.

    Science.gov (United States)

    Zhang, Chao; Hao, Xiao-Li; Wang, Cui-Xia; Wei, Ning; Rabczuk, Timon

    2017-01-25

    Tensile strain and compress strain can greatly affect the thermal conductivity of graphene nanoribbons (GNRs). However, the effect of GNRs under shear strain, which is also one of the main strain effect, has not been studied systematically yet. In this work, we employ reverse nonequilibrium molecular dynamics (RNEMD) to the systematical study of the thermal conductivity of GNRs (with model size of 4 nm × 15 nm) under the shear strain. Our studies show that the thermal conductivity of GNRs is not sensitive to the shear strain, and the thermal conductivity decreases only 12-16% before the pristine structure is broken. Furthermore, the phonon frequency and the change of the micro-structure of GNRs, such as band angel and bond length, are analyzed to explore the tendency of thermal conductivity. The results show that the main influence of shear strain is on the in-plane phonon density of states (PDOS), whose G band (higher frequency peaks) moved to the low frequency, thus the thermal conductivity is decreased. The unique thermal properties of GNRs under shear strains suggest their great potentials for graphene nanodevices and great potentials in the thermal managements and thermoelectric applications.

  16. Atomistic simulation study of the shear-band deformation mechanism in Mg-Cu metallic glasses

    DEFF Research Database (Denmark)

    Bailey, Nicholas; Schiøtz, Jakob; Jacobsen, Karsten Wedel

    2006-01-01

    We have simulated plastic deformation of a model Mg-Cu metallic glass in order to study shear banding. In uniaxial tension, we find a necking instability occurs rather than shear banding. We can force the latter to occur by deforming in plane strain, forbidding the change of length in one...... of the transverse directions. Furthermore, in most of the simulations a notch is used to initiate shear bands, which lie at a 45 degrees angle to the tensile loading direction. The shear bands are characterized by the Falk and Langer local measure of plastic deformation D-min(2), averaged here over volumes...... containing many atoms. The D-min(2) profile has a peak whose width is around 10 nm; this width is largely independent of the strain rate. Most of the simulations were, at least nominally, at 100 K, about T-g/3 for this system. The development of the shear bands takes a few tens of ps, once plastic flow has...

  17. Magnetic Field Shear in Kinetic Models Steps Toward Understanding Magnetic Reconnection Drivers

    Science.gov (United States)

    Black, Carrie; Antiochos, Spiro; DeVore, Rick; Karpen, Judith

    2015-11-01

    In the standard model for coronal mass ejections (CME) and/or solar flares, the free energy for the eruptive event resides in a strongly sheared magnetic. A pre-eruption force balance consists of an upward force due to the magnetic pressure of the sheared field and a downward tension due to overlying unsheared field. Magnetic reconnection disrupts this force balance; therefore, it is critical for understanding CME/flare initiation, to model the onset of reconnection driven by the build-up of magnetic shear. In MHD simulations, the application of a magnetic-field shear is a trivial matter. However, kinetic effects are dominant in the diffusion region and thus, it is important to examine this process with PIC simulations as well. The implementation of such a driver in PIC methods is challenging, however, and indicates the necessity of a true multiscale model for such processes in the solar environment. The field must be sheared self-consistently and indirectly to prevent the generation of waves that destroy the desired system. Plasma instabilities can arise nonetheless. Here, we show that we can control this instability and generate a predicted out-of-plane magnetic flux. This material is based upon work supported by the National Science Foundation under Award No. AGS-1331356.

  18. An Octahedral Shear Strain Based measure of SNR for 3D MR Elastography

    Science.gov (United States)

    McGarry, MDJ; Van Houten, EEW; Perriñez, PR; Pattison, AJ; Weaver, JB; Paulsen, KD

    2011-01-01

    A signal to noise ratio (SNR) measure based on the octahedral shear strain (the maximum shear strain in any plane for a 3D state of strain) is presented for MR elastography, where motion-based SNR measures are commonly used. The shear strain, γ, is directly related to the shear modulus, μ, through the definition of shear stress, τ = μγ. Therefore, noise in the strain is the important factor in determining the quality of motion data, rather than the noise in the motion. Motion and strain SNR measures were found to be correlated for MRE of gelatin phantoms and human breast. Analysis of the stiffness distributions of phantoms reconstructed from the measured motion data revealed a threshold for both strain and motion SNR where MRE stiffness estimates match independent mechanical testing. MRE of the feline brain showed significantly less correlation between the two SNR measures. The strain SNR measure had a threshold above which the reconstructed stiffness values were consistent between cases, whereas the motion SNR measure did not provide a useful threshold, primarily due to rigid body motion effects. PMID:21654044

  19. An octahedral shear strain-based measure of SNR for 3D MR elastography.

    Science.gov (United States)

    McGarry, M D J; Van Houten, E E W; Perriñez, P R; Pattison, A J; Weaver, J B; Paulsen, K D

    2011-07-07

    A signal-to-noise ratio (SNR) measure based on the octahedral shear strain (the maximum shear strain in any plane for a 3D state of strain) is presented for magnetic resonance elastography (MRE), where motion-based SNR measures are commonly used. The shear strain, γ, is directly related to the shear modulus, μ, through the definition of shear stress, τ = μγ. Therefore, noise in the strain is the important factor in determining the quality of motion data, rather than the noise in the motion. Motion and strain SNR measures were found to be correlated for MRE of gelatin phantoms and the human breast. Analysis of the stiffness distributions of phantoms reconstructed from the measured motion data revealed a threshold for both strain and motion SNR where MRE stiffness estimates match independent mechanical testing. MRE of the feline brain showed significantly less correlation between the two SNR measures. The strain SNR measure had a threshold above which the reconstructed stiffness values were consistent between cases, whereas the motion SNR measure did not provide a useful threshold, primarily due to rigid body motion effects.

  20. Thermal conductivity of graphene nanoribbons under shear deformation: A molecular dynamics simulation

    Science.gov (United States)

    Zhang, Chao; Hao, Xiao-Li; Wang, Cui-Xia; Wei, Ning; Rabczuk, Timon

    2017-01-01

    Tensile strain and compress strain can greatly affect the thermal conductivity of graphene nanoribbons (GNRs). However, the effect of GNRs under shear strain, which is also one of the main strain effect, has not been studied systematically yet. In this work, we employ reverse nonequilibrium molecular dynamics (RNEMD) to the systematical study of the thermal conductivity of GNRs (with model size of 4 nm × 15 nm) under the shear strain. Our studies show that the thermal conductivity of GNRs is not sensitive to the shear strain, and the thermal conductivity decreases only 12–16% before the pristine structure is broken. Furthermore, the phonon frequency and the change of the micro-structure of GNRs, such as band angel and bond length, are analyzed to explore the tendency of thermal conductivity. The results show that the main influence of shear strain is on the in-plane phonon density of states (PDOS), whose G band (higher frequency peaks) moved to the low frequency, thus the thermal conductivity is decreased. The unique thermal properties of GNRs under shear strains suggest their great potentials for graphene nanodevices and great potentials in the thermal managements and thermoelectric applications. PMID:28120921

  1. Shear induced inactivation of a-amylase in a plain shear field

    NARCIS (Netherlands)

    Veen, van der M.E.; Iersel, van D.G.; Goot, van der A.J.; Boom, R.M.

    2004-01-01

    A newly developed shearing device was used to study shear-induced inactivation of thermostable alpha-amylase in a plain shear field, under conditions comparable to extrusion. The results show that the inactivation can be described well with a first-order process, in which the inactivation energy lar

  2. Shear induced inactivation of a-amylase in a plain shear field

    NARCIS (Netherlands)

    Veen, van der M.E.; Iersel, van D.G.; Goot, van der A.J.; Boom, R.M.

    2004-01-01

    A newly developed shearing device was used to study shear-induced inactivation of thermostable alpha-amylase in a plain shear field, under conditions comparable to extrusion. The results show that the inactivation can be described well with a first-order process, in which the inactivation energy

  3. Effect of fracture surface roughness on shear crack growth

    Energy Technology Data Exchange (ETDEWEB)

    Gross, T.S.; Watt, D.W. (New Hampshire Univ., Durham, NH (United States). Dept. of Mechanical Engineering); Mendelsohn, D.A. (Ohio State Univ., Columbus, OH (United States). Dept. of Engineering Mechanics)

    1992-12-01

    A model of fracture surface interference for Mode I fatigue crack profiles was developed and evaluated. Force required to open the crack faces is estimated from point contact expressions for Mode I stress intensity factor. Force transfer across contacting asperities is estimated and used to calculate Mode II resistance stress intensity factor (applied factor is sum of effective and resistance factors). Electro-optic holographic interferometry was used to measure 3-D displacement field around a Mode I fatigue pre-crack in Al loaded in Mode II shear. Induced Mode I crack face displacements were greater than Mode II displacements. Plane stress shear lip caused displacement normal to surface as the crack faces are displaced. Algorithms are being developed to track the displacements associated with the original coordinate system in the camera. A 2-D boundary element method code for mixed mode I and II loading of a rough crack (sawtooth asperity model) has been completed. Addition of small-scale crack tip yielding and a wear model are completed and underway, respectively.

  4. Feedback control of flow alignment in sheared liquid crystals.

    Science.gov (United States)

    Strehober, David A; Schöll, Eckehard; Klapp, Sabine H L

    2013-12-01

    Based on a continuum theory, we investigate the manipulation of the nonequilibrium behavior of a sheared liquid crystal via closed-loop feedback control. Our goal is to stabilize a specific dynamical state, that is, the stationary "flow alignment," under conditions where the uncontrolled system displays oscillatory director dynamics with in-plane symmetry. To this end we employ time-delayed feedback control (TDFC), where the equation of motion for the ith component q(i)(t) of the order parameter tensor is supplemented by a control term involving the difference q(i)(t)-q(i)(t-τ). In this diagonal scheme, τ is the delay time. We demonstrate that the TDFC method successfully stabilizes flow alignment for suitable values of the control strength K and τ; these values are determined by solving an exact eigenvalue equation. Moreover, our results show that only small values of K are needed when the system is sheared from an isotropic equilibrium state, contrary to the case where the equilibrium state is nematic.

  5. Oblique waves on a vertically sheared current are rotational

    CERN Document Server

    Ellingsen, Simen Å

    2015-01-01

    In the study of surface waves in the presence of a shear current, a useful and much studied model is that in which the shear flow has constant vorticity. Recently it was shown by Constantin [Eur. J. Mech. B/Fluids 30 (2011) 12-16] that a flow of constant vorticity can only permit waves travelling exactly upstream or downstream, but not at oblique angles to the current, and several proofs to the same effect have appeared thereafter. Physical waves cannot possibly adhere to such a restriction, however. We resolve the paradox by showing that an oblique plane wave propagating atop a current of constant vorticity according to the linearized Euler equation carries with it an undulating perturbation of the vorticity field, hence is not prohibited by the Constantin theorem since vorticity is not constant. The perturbation of the vorticity field is readily interpreted in a Lagrangian perspective as the wave motion gently shifting and twisting the vortex lines as the wave passes. In the special case of upstream or down...

  6. Large Format Uncooled Focal Plane Array Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Uncooled focal plane arrays have improved dramatically and array sizes of 320x240 elements in a 50-?m pitch are commercially available at affordable cost. Black...

  7. Causal inheritence in plane wave quotients

    Energy Technology Data Exchange (ETDEWEB)

    Hubeny, Veronika E.; Rangamani, Mukund; Ross, Simon F.

    2003-11-24

    We investigate the appearance of closed timelike curves in quotients of plane waves along spacelike isometries. First we formulate a necessary and sufficient condition for a quotient of a general spacetime to preserve stable causality. We explicitly show that the plane waves are stably causal; in passing, we observe that some pp-waves are not even distinguishing. We then consider the classification of all quotients of the maximally supersymmetric ten-dimensional plane wave under a spacelike isometry, and show that the quotient will lead to closed timelike curves iff the isometry involves a translation along the u direction. The appearance of these closed timelike curves is thus connected to the special properties of the light cones in plane wave spacetimes. We show that all other quotients preserve stable causality.

  8. Titanium Heat Pipe Thermal Plane Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Thermacore Inc. proposes an innovative titanium heat pipe thermal plane for passive thermal control of individual cells within a fuel cell stack. The proposed...

  9. Titanium Heat Pipe Thermal Plane Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of the Phase II program is to complete the development of the titanium heat pipe thermal plane and establish all necessary steps for production of this...

  10. Equivalent boundary integral equations for plane elasticity

    Institute of Scientific and Technical Information of China (English)

    胡海昌; 丁皓江; 何文军

    1997-01-01

    Indirect and direct boundary integral equations equivalent to the original boundary value problem of differential equation of plane elasticity are established rigorously. The unnecessity or deficiency of some customary boundary integral equations is indicated by examples and numerical comparison.

  11. Linear connections on the quantum plane

    CERN Document Server

    Dubois-Violette, M; Masson, T; Mourad, J; Dubois-Violette, Michel; Madore, John; Masson, Thierry; Mourad, Jihad

    1994-01-01

    A general definition has been proposed recently of a linear connection and a metric in noncommutative geometry. It is shown that to within normalization there is a unique linear connection on the quantum plane and there is no metric.

  12. Parallels plane projection and its geometric features

    Institute of Scientific and Technical Information of China (English)

    ZHOU ChengHu; MA Ting; YANG Liao; QIN Biao

    2007-01-01

    A new equivalent map projection called the parallels plane projection is proposed in this paper. The transverse axis of the parallels plane projection is the expansion of the equator and its vertical axis equals half the length of the central meridian. On the parallels plane projection, meridians are projected as sine curves and parallels are a series of straight, parallel lines. No distortion of length occurs along the central meridian or on any parallels of this projection. Angular distortion and the proportion of length along meridians (except the central meridian) introduced by the projection transformation increase with increasing longitude and latitude. A potential application of the parallels plane projection is that it can provide an efficient projection transformation for global discrete grid systems.

  13. Metrics and causality on Moyal planes

    CERN Document Server

    Franco, Nicolas

    2015-01-01

    Metrics structures stemming from the Connes distance promote Moyal planes to the status of quantum metric spaces. We discuss this aspect in the light of recent developments, emphasizing the role of Moyal planes as representative examples of a recently introduced notion of quantum (noncommutative) locally compact space. We move then to the framework of Lorentzian noncommutative geometry and we examine the possibility of defining a notion of causality on Moyal plane, which is somewhat controversial in the area of mathematical physics. We show the actual existence of causal relations between the elements of a particular class of pure (coherent) states on Moyal plane with related causal structure similar to the one of the usual Minkowski space, up to the notion of locality.

  14. Large Eddy Simulation of Spatially Developing Turbulent Reacting Shear Layers with the One-Dimensional Turbulence Model

    Science.gov (United States)

    Hoffie, Andreas Frank

    model. The chemical reaction is simulated with a global single-step, second-order equilibrium reaction with an Arrhenius reaction rate. The two benchmark cases of constant density reacting and variable density non-reacting shear layers used to determine ODT parameters yield perfect agreement with regards to first and second-order flow statistics as well as shear layer growth rate. The variable density non-reacting shear layer also serves as a testing case for the LES-ODT model to simulate passive scalar mixing. The variable density, reacting shear layer cases only agree reasonably well and indicate that more work is necessary to improve variable density coupling of ODT and LES. The disagreement is attributed to the fact that the ODT filtered density is kept constant across the Runge-Kutta steps. Furthermore, a more in-depth knowledge of large scale and subgrid turbulent kinetic energy (TKE) spectra at several downstream locations as well as TKE budgets need to be studied to obtain a better understanding about the model as well as about the flow under investigation. The local Reynolds number based on the one-percent thickness at the exit is Redelta ≈ 5300, for the constant density reacting and for the variable density non-reacting case. For the variable density reacting shear layer, the Reynolds number based on the 1% thickness is Redelta ≈ 2370. The variable density reacting shear layers show suppressed growth rates due to density variations caused by heat release. This has also been reported in literature. A Lewis number parameter study is performed to extract non-unity Lewis number effects. An increase in the Lewis number leads to a further suppression of the growth rate, however to an increase spread of second-order flow statistics. Major focus and challenge of this work is to improve and advance the three-dimensional coupling of the one-dimensional ODT domains while keeping the solution correct. This entails major restructuring of the model. The turbulent

  15. Shear Viscosity from Lattice QCD

    CERN Document Server

    Mages, Simon W; Fodor, Zoltán; Schäfer, Andreas; Szabó, Kálmán

    2015-01-01

    Understanding of the transport properties of the the quark-gluon plasma is becoming increasingly important to describe current measurements at heavy ion collisions. This work reports on recent efforts to determine the shear viscosity h in the deconfined phase from lattice QCD. The main focus is on the integration of the Wilson flow in the analysis to get a better handle on the infrared behaviour of the spectral function which is relevant for transport. It is carried out at finite Wilson flow time, which eliminates the dependence on the lattice spacing. Eventually, a new continuum limit has to be carried out which sends the new regulator introduced by finite flow time to zero. Also the non-perturbative renormalization strategy applied for the energy momentum tensor is discussed. At the end some quenched results for temperatures up to 4 : 5 T c are presented

  16. Inverse Magnetic/Shear Catalysis

    CERN Document Server

    McInnes, Brett

    2015-01-01

    It is well known that very large magnetic fields are generated when the Quark-Gluon Plasma is formed during peripheral heavy-ion collisions. Lattice, holographic, and other studies strongly suggest that these fields may, for observationally relevant field values, induce ``inverse magnetic catalysis'', signalled by a lowering of the critical temperature for the chiral/deconfinement transition. The theoretical basis of this effect has recently attracted much attention; yet so far these investigations have not included another, equally dramatic consequence of the peripheral collision geometry: the QGP acquires a large angular momentum vector, parallel to the magnetic field. Here we use holographic techniques to argue that the angular momentum can also, independently, have an effect on transition temperatures, and we obtain a rough estimate of the relative effects of the presence of both a magnetic field and an angular momentum density. We find that the shearing angular momentum reinforces the effect of the magne...

  17. Faddeev Null Plane Model of Proton

    CERN Document Server

    D'Araújo, W R B; Frederico, T

    1998-01-01

    The proton is formulated as a relativistic system of three constituent quarks interacting via a zero-range two-body force in the null-plane. The covariance of the null-plane Faddeev-like equation under kinematical front-form boosts is discussed. A simplified three-boson model of the nucleon wave-function is obtained numerically. The proton electric form-factor reproduces the experimental data for low momentum transfers and qualitatively describes the asymptotic region.

  18. Ostrowski Type Inequalities in the Grushin Plane

    Directory of Open Access Journals (Sweden)

    Liu Heng-Xing

    2010-01-01

    Full Text Available Motivated by the work of B.-S. Lian and Q.-H. Yang (2010 we proved an Ostrowski inequality associated with Carnot-Carathéodory distance in the Grushin plane. The procedure is based on a representation formula. Using the same representation formula, we prove some Hardy type inequalities associated with Carnot-Carathéodory distance in the Grushin plane.

  19. Deep-Plane Lipoabdominoplasty in East Asians

    OpenAIRE

    Kim, June-kyu; Jang, Jun-Young; Hong, Yoon Gi; Sim, Hyung Bo; Sun, Sang Hoon

    2016-01-01

    Background The objective of this study was to develop a new surgical technique by combining traditional abdominoplasty with liposuction. This combination of operations permits simpler and more accurate management of various abdominal deformities. In lipoabdominoplasty, the combination of techniques is of paramount concern. Herein, we introduce a new combination of liposuction and abdominoplasty using deep-plane flap sliding to maximize the benefits of both techniques. Methods Deep-plane lipoa...

  20. Kinematic, finite strain and vorticity analysis of the Sisters Shear Zone, Stewart Island, New Zealand

    Science.gov (United States)

    Ring, Uwe; Bernet, Matthias; Tulloch, Andy

    2015-04-01

    The Sisters Shear Zone (SSZ) on Stewart Island, New Zealand, is a greenschist-facies extensional shear zone active prior to and possibly during the development of the Pacific-Antarctica spreading ridge at ˜76 Ma. We report quantitative kinematic and rotation data as well as apatite fission-track (AFT) ages from the SSZ. Early kinematic indicators associated with the NNE-trending stretching lineation formed under upper greenschist-facies metamorphism and show alternating top-to-the-NNW and top-to-the-SSE senses of shear. During progressive exhumation lowermost greenschist-facies and brittle-ductile kinematic indicators depict a more uniform top-to-the-SSE sense of shear in the topmost SSZ just below the detachment plane. Deformed metagranites in the SSZ allow the reconstruction of deformation and flow parameters. The mean kinematic vorticity number (Wm) ranges from 0.10 to 0.89; smaller numbers prevail in the deeper parts of the shear zone with a higher degree of simple shear deformation in the upper parts of the shear zone (deeper and upper parts relate to present geometry). High finite strain intensity correlates with low Wm and high Wm numbers near the detachment correlate with relatively weak strain intensity. Finite strain shows oblate geometries. Overall, our data indicate vertical and possibly temporal variations in deformation of the SSZ. Most AFT ages cluster around 85-75 Ma. We interpret the AFT ages to reflect the final stages of continental break-up just before and possibly during the initiation of sea-floor spreading between New Zealand and Antarctica.