WorldWideScience

Sample records for nonmetal mines explosives

  1. 30 CFR 57.22313 - Explosion-protection systems (I-C mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosion-protection systems (I-C mines). 57... MINES Safety Standards for Methane in Metal and Nonmetal Mines Equipment § 57.22313 Explosion-protection systems (I-C mines). Pressure-relief systems including vents, or explosion suppression systems, shall...

  2. Quartz concentration trends in metal and nonmetal mining.

    Science.gov (United States)

    Watts, Winthrop F; Huynh, Tran B; Ramachandran, Gurumurthy

    2012-01-01

    From 1974 through 2010, the Mine Safety and Health Administration (MSHA) collected nearly 147,000 respirable dust samples with a mass of at least 0.1 mg and a minimum of 1% quartz. These samples represent about 50% of all respirable dust compliance samples collected by MSHA. Analysis of these data shows that pockets of high concentrations and overexposure continue to exist. At underground mines, from 2005 to 2010, occupations with >20% of the samples exceeding the permissible exposure limit (PEL) and geometric mean quartz concentrations exceeding the ACGIH threshold limit value of 25 μg/m(3) included mucking, crusher operator, general laborer/utility, and front-end loader operator. During the same period, stone and rock saw operators and bagger and packers working at surface mines and mills also had >20% of the samples exceeding the PEL and geometric mean quartz concentrations >25 μg/m(3). Regardless of mine type or location, slow but steady improvement in exposure levels is seen in jobs involving crushing operations, which are widespread in the mining industry. Crusher operators are more likely to work in an enclosed area where it is easier to apply dust controls and air conditioning. A downward trend is also observed for vehicle equipment operators who drive load-haul-dumps, front-end loaders, trucks, and similar equipment. Crusher operators and vehicle equipment operators represent occupational categories that are widely sampled by MSHA inspectors. A small but statistically significant reduction in the overall mean respirable quartz dust and quartz concentrations from 1993 to 2010 was observed in most commodity groups. Variability from year to year and between commodities is high. Reduction in respirable quartz dust concentration does not necessarily correspond to a reduction in quartz concentration within the same commodity group. These trends are consistent with those reported in previous studies.

  3. The diesel exhaust in miners study: IV. Estimating historical exposures to diesel exhaust in underground non-metal mining facilities.

    NARCIS (Netherlands)

    Vermeulen, R.; Coble, J.B.; Lubin, J.H.; Portengen, L.; Blair, A.; Attfield, M.D.; Silverman, D.T.; Stewart, P.A.

    2010-01-01

    We developed quantitative estimates of historical exposures to respirable elemental carbon (REC) for an epidemiologic study of mortality, including lung cancer, among diesel-exposed miners at eight non-metal mining facilities [the Diesel Exhaust in Miners Study (DEMS)]. Because there were no histori

  4. 30 CFR 56.6205 - Conveying explosives by hand.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Conveying explosives by hand. 56.6205 Section... NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Explosives Transportation § 56.6205 Conveying explosives by hand. Closed, nonconductive containers shall be used to carry...

  5. 30 CFR 57.6205 - Conveying explosives by hand.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Conveying explosives by hand. 57.6205 Section... NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Explosives Transportation-Surface and Underground § 57.6205 Conveying explosives by hand. Closed, nonconductive containers...

  6. The relationship between elemental carbon and diesel particulate matter in underground metal/nonmetal mines in the United States and coal mines in Australia.

    Science.gov (United States)

    Noll, James; Gilles, Stewart; Wu, Hsin Wei; Rubinstein, Elaine

    2015-01-01

    In the United States, total carbon (TC) is used as a surrogate for determining diesel particulate matter (DPM) compliance exposures in underground metal/nonmetal mines. Since TC can be affected by interferences and elemental carbon (EC) is not, one method used to estimate the TC concentration is to multiply the EC concentration from the personal sample by a conversion factor to avoid the influence of potential interferences. Since there is no accepted single conversion factor for all metal/nonmetal mines, one is determined every time an exposure sample is taken by collecting an area sample that represents the TC/EC ratio in the miner's breathing zone and is away from potential interferences. As an alternative to this procedure, this article investigates the relationship between TC and EC from DPM samples to determine if a single conversion factor can be used for all metal/nonmetal mines. In addition, this article also investigates how well EC represents DPM concentrations in Australian coal mines since the recommended exposure limit for DPM in Australia is an EC value. When TC was predicted from EC values using a single conversion factor of 1.27 in 14 US metal/nonmetal mines, 95% of the predicted values were within 18% of the measured value, even at the permissible exposure limit (PEL) concentration of 160 μg/m(3) TC. A strong correlation between TC and EC was also found in nine underground coal mines in Australia.

  7. Hemodynamic Disorders in Explosive Mine Injury: Experimental Study

    OpenAIRE

    V. N Yelsky; G. K. Krivobok; A. N. Talalayenko; A. A. Redko; A. Yu. Kryuk

    2005-01-01

    The authors have studied hemodynamic features in explosive mine injury in the presence or absence of a preliminary exposure to premorbid mining factors. A combined influence of premorbid mining factors following an explosive mine injury has been ascertained to induce more severe systemic and cerebral hemodynamic disorders than an isolated explosive mine injury.

  8. Numerical computation algorithm of explosion equations and thermodynamics parameters of mine explosives

    Institute of Scientific and Technical Information of China (English)

    李守巨; 刘迎曦; 何翔; 周圆π

    2001-01-01

    A new numerical algorithm is presented to simulate the explosion reaction process of mine explosives based on the equation of state, the equation of mass conservation and thermodynamics balance equation of explosion products. With the affection of reversible reaction of explosion products to explosion reaction equations and thermodynamics parameters considered, the computer program has been developed. The computation values show that computer simulation results are identical with the testinq ones.

  9. Numerical computation algorithm of explosion equations and thermodynamics parameters of mine explosives

    Institute of Scientific and Technical Information of China (English)

    LI Shou-ju; LIU Ying-xi; HE Xiang; ZHOU Y uan-pai

    2001-01-01

    A new numerical algorithm is presented to simulate the explosion reacti on process of mine explosives based on the equation of state, the equation of ma ss conservation and thermodynamics balance equation of explosion products. With the affection of reversible reaction of explosion products to explosion reaction equations and thermodynamics parameters considered, the computer program has be en developed. The computation values show that computer simulation results are i dentical with the testing ones.

  10. 30 CFR 57.6131 - Location of explosive material storage facilities.

    Science.gov (United States)

    2010-07-01

    ... NONMETAL MINES Explosives Storage-Surface Only § 57.6131 Location of explosive material storage facilities... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Location of explosive material storage facilities. 57.6131 Section 57.6131 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF...

  11. The Diesel Exhaust in Miners Study: IV. Estimating historical exposures to diesel exhaust in underground non-metal mining facilities.

    Science.gov (United States)

    Vermeulen, Roel; Coble, Joseph B; Lubin, Jay H; Portengen, Lützen; Blair, Aaron; Attfield, Michael D; Silverman, Debra T; Stewart, Patricia A

    2010-10-01

    We developed quantitative estimates of historical exposures to respirable elemental carbon (REC) for an epidemiologic study of mortality, including lung cancer, among diesel-exposed miners at eight non-metal mining facilities [the Diesel Exhaust in Miners Study (DEMS)]. Because there were no historical measurements of diesel exhaust (DE), historical REC (a component of DE) levels were estimated based on REC data from monitoring surveys conducted in 1998-2001 as part of the DEMS investigation. These values were adjusted for underground workers by carbon monoxide (CO) concentration trends in the mines derived from models of historical CO (another DE component) measurements and DE determinants such as engine horsepower (HP; 1 HP = 0.746 kW) and mine ventilation. CO was chosen to estimate historical changes because it was the most frequently measured DE component in our study facilities and it was found to correlate with REC exposure. Databases were constructed by facility and year with air sampling data and with information on the total rate of airflow exhausted from the underground operations in cubic feet per minute (CFM) (1 CFM = 0.0283 m³ min⁻¹), HP of the diesel equipment in use (ADJ HP), and other possible determinants. The ADJ HP purchased after 1990 (ADJ HP₁₉₉₀(+)) was also included to account for lower emissions from newer, cleaner engines. Facility-specific CO levels, relative to those in the DEMS survey year for each year back to the start of dieselization (1947-1967 depending on facility), were predicted based on models of observed CO concentrations and log-transformed (Ln) ADJ HP/CFM and Ln(ADJ HP₁₉₉₀(+)). The resulting temporal trends in relative CO levels were then multiplied by facility/department/job-specific REC estimates derived from the DEMS surveys personal measurements to obtain historical facility/department/job/year-specific REC exposure estimates. The facility-specific temporal trends of CO levels (and thus the REC

  12. NONMETALS DEPOSITS

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>20112372An Lianying(Chengdu University of Technology,Chengdu 610059,China); Yin Huian Feasibility Study of Leaching Mining of Deeply Buried Polyhalite and Kinetic Leaching Modeling (Acta Geologica

  13. 30 CFR 57.22607 - Blasting on shift (III mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Blasting on shift (III mines). 57.22607 Section... Standards for Methane in Metal and Nonmetal Mines Explosives § 57.22607 Blasting on shift (III mines). When blasting on shift, tests for methane shall be made in the mine atmosphere by a competent person...

  14. Program of mining research, 1998--1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    The paper contains: Reflections on 1998; Project summaries; Noise; Injury prevention, ergonomics, and human factors; Surface, sand and gravel, and stone mines; Hazard detection and warning devices; Ground control -- metal/nonmetal mines; Ground control -- coal mines; Explosion and fire detection and suppression; Methane detection; Electrical hazards; Emerging technologies; Surveillance; Construction; Training and education; and Communication activity.

  15. Mining explosion identification as an application to treaty verification

    Science.gov (United States)

    Arrowsmith, Marie

    With the contribution of data from an increasing number of high-quality seismic stations and networks throughout the globe, the event detection threshold is reduced to smaller and smaller magnitudes. At M4 and below, delay-fired explosions are often commonly observed along with natural seismicity. The addition of this class within an event catalog leads to several questions which much be addressed: (1) can delay-fired mining explosions be discriminated from earthquakes; (2) can the understanding of mining discriminants illuminate the explosion discrimination process in regions where there are no known nuclear explosions; and (3) are mining discriminants regionally dependent, and are there corrections to account for this dependence? A broader question is in understanding the ability to separate source and propagation path effects from regional data. Addressing this question utilizing growing regional dataset has direct application to the problems noted above but more generally to our ability to interpret regional seismic records from all types of events including earthquakes. To address these types of questions, we have assembled a database of ˜2500 mining explosions and ˜1300 earthquakes recorded at a number of regional stations, comprising a total of ˜150,000 waveforms. The database is focused on two regions, the Western US and the Altai-Sayan region of Russia, which are both areas of prolific mining activity. As part of an extensive collaboration with the largest coal mine in Wyoming and the nation, we have detailed shot information for ˜1000 mining events, classified into six distinct blast types. We have limited information for events in the Altai-Sayan based upon contacts with the ASSE. We have applied three discriminants to data from 11 stations and one array in the WUS. The first discriminant, amplitude ratios, exploits differences between regional phases due to source type. Results are highly station centric, although the largest mining events separate

  16. Atmospheric emission of NOx from mining explosives: A critical review

    Science.gov (United States)

    Oluwoye, Ibukun; Dlugogorski, Bogdan Z.; Gore, Jeff; Oskierski, Hans C.; Altarawneh, Mohammednoor

    2017-10-01

    High-energy materials such as emulsions, slurries and ammonium-nitrate fuel-oil (ANFO) explosives play crucial roles in mining, quarrying, tunnelling and many other infrastructure activities, because of their excellent transport and blasting properties. These explosives engender environmental concerns, due to atmospheric pollution caused by emission of dust and nitrogen oxides (NOx) from blasts, the latter characterised by the average emission factor of 5 kg (t AN explosive)-1. This first-of-its-kind review provides a concise literature account of the formation of NOx during blasting of AN-based explosives, employed in surface operations. We estimate the total NOx emission rate from AN-based explosives as 0.05 Tg (i.e., 5 × 104 t) N per annum, compared to the total global annual anthropogenic NOx emissions of 41.3 × 106 t N y-1. Although minor in the global sense, the large localised plumes from blasting exhibit high NOx concentration (500 ppm) exceeding up to 3000 times the international standards. This emission has profound consequences at mining sites and for adjacent atmospheric environment, necessitating expensive management of exclusion zones. The review describes different types of AN energetic materials for civilian applications, and summarises the essential properties and terminologies pertaining to their use. Furthermore, we recapitulate the mechanisms that lead to the formation of the reactive nitrogen species in blasting of AN-based explosives, review their implications to atmospheric air pollution, and compare the mechanisms with those experienced in other thermal and combustion operations. We also examine the mitigation approaches, including guidelines and operational-control measures. The review discusses the abatement technologies such as the formulation of new explosive mixtures, comprising secondary fuels, spin traps and other additives, in light of their effectiveness and efficiency. We conclude the review with a summary of unresolved problems

  17. 30 CFR 57.22602 - Blasting from the surface (I-C mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Blasting from the surface (I-C mines). 57.22602... Standards for Methane in Metal and Nonmetal Mines Explosives § 57.22602 Blasting from the surface (I-C mines). (a) All blasting shall be initiated from the surface after all persons are out of the mine and...

  18. 30 CFR 57.22604 - Blasting from the surface (II-B mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Blasting from the surface (II-B mines). 57.22604 Section 57.22604 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... MINES Safety Standards for Methane in Metal and Nonmetal Mines Explosives § 57.22604 Blasting from...

  19. 30 CFR 57.22603 - Blasting from the surface (II-A mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Blasting from the surface (II-A mines). 57.22603 Section 57.22603 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... MINES Safety Standards for Methane in Metal and Nonmetal Mines Explosives § 57.22603 Blasting from...

  20. Development of mine explosion ground truth smart sensors

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, Steven R. [Rocky Mountain Geophysics, Inc., Los Alamos, NM (United States); Harben, Phillip E. [Rocky Mountain Geophysics, Inc., Los Alamos, NM (United States); Jarpe, Steve [Jarpe Data Solutions, Prescott, AZ (United States); Harris, David B. [Deschutes Signal Processing, Maupin, OR (United States)

    2015-09-14

    Accurate seismo-acoustic source location is one of the fundamental aspects of nuclear explosion monitoring. Critical to improved location is the compilation of ground truth data sets for which origin time and location are accurately known. Substantial effort by the National Laboratories and other seismic monitoring groups have been undertaken to acquire and develop ground truth catalogs that form the basis of location efforts (e.g. Sweeney, 1998; Bergmann et al., 2009; Waldhauser and Richards, 2004). In particular, more GT1 (Ground Truth 1 km) events are required to improve three-dimensional velocity models that are currently under development. Mine seismicity can form the basis of accurate ground truth datasets. Although the location of mining explosions can often be accurately determined using array methods (e.g. Harris, 1991) and from overhead observations (e.g. MacCarthy et al., 2008), accurate origin time estimation can be difficult. Occasionally, mine operators will share shot time, location, explosion size and even shot configuration, but this is rarely done, especially in foreign countries. Additionally, shot times provided by mine operators are often inaccurate. An inexpensive, ground truth event detector that could be mailed to a contact, placed in close proximity (< 5 km) to mining regions or earthquake aftershock regions that automatically transmits back ground-truth parameters, would greatly aid in development of ground truth datasets that could be used to improve nuclear explosion monitoring capabilities. We are developing an inexpensive, compact, lightweight smart sensor unit (or units) that could be used in the development of ground truth datasets for the purpose of improving nuclear explosion monitoring capabilities. The units must be easy to deploy, be able to operate autonomously for a significant period of time (> 6 months) and inexpensive enough to be discarded after useful operations have expired (although this may not be part of our business

  1. Development of Mine Explosion Ground Truth Smart Sensors

    Science.gov (United States)

    2011-09-01

    DEVELOPMENT OF MINE EXPLOSION GROUND TRUTH SMART SENSORS Steven R. Taylor1, Phillip E. Harben1, Steve Jarpe2, and David B. Harris3 Rocky...improved location is the compilation of ground truth data sets for which origin time and location are accurately known. Substantial effort by the...National Laboratories and seismic monitoring groups have been undertaken to acquire and develop ground truth catalogs that form the basis of location

  2. Research on numerical emulator of mine methane and coal dust explosion

    Institute of Scientific and Technical Information of China (English)

    CAI Zhou-quan; Niu Steve

    2008-01-01

    The mathematical physics model of mine methane and coal dust explosionpropagation was established in the research, by using continuous phase, combustion, par-ticulate equations of mathematical physics. Based upon the data from mine methanedrainage roadway explosion, and mine methane and coal dust explosion propagation ex-perimental studies, the numerical emulator system of mine methane and coal dust explo-sion software was developed by using prevalent flow simulation platform, which can beused to simulate the explosion accidents process effectively. In addition, the system canalso be used to determine whether coal dust involved in the explosion, and to simulateaccurately the transition from deflagration to detonation in methane explosion, propagationvelocity of explosion shock, attenuation pattern, and affected area of explosion.

  3. Tele-infrasonic studies of hard-rock mining explosions.

    Science.gov (United States)

    McKenna, Mihan H; Stump, Brian W; Hayek, Sylvia; McKenna, Jason R; Stanton, Terry R

    2007-07-01

    The Lac-du-Bonnet infrasound station, IS-10, and the Minnesota iron mines 390 km to the southeast are ideally located to assess the accuracy of atmospheric profiles needed for infrasound modeling. Infrasonic data from 2003 associated with explosions at the iron mine were analyzed for effects of explosion size and atmospheric conditions on observations with well-constrained ground truth. Noise was the determining factor for observation; high noise conditions sometimes prevented unequivocal identification of infrasound arrivals. Observed arrivals had frequencies of 0.5 to 5 Hz, with a dominant frequency of 2 Hz, and generally had durations on the order of 10 s or less. There was no correlation between explosive amount and observability. Tele-infrasonic propagation distances (greater than 250 km) produce thermospheric ray paths. Modeling is based upon MSIS/HWM (Mass Spectrometer Incoherent Scatter/Horizontal Wind Model) and NRL-G2S (Naval Research Laboratory Ground to Space) datasets. The NRL-G2S dataset provided more accurate travel time predictions that the MSIS/HWM dataset. PE modeling for the NRL-G2S dataset indicates energy loss at higher frequencies (around 4 Hz). Additionally, applying the Sutherland/Bass model through the NRL-G2S realization of the atmosphere in InfraMAP results in predicted amplitudes too small to be observed.

  4. 30 CFR 57.22601 - Blasting from the surface (I-A mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Blasting from the surface (I-A mines). 57.22601... Standards for Methane in Metal and Nonmetal Mines Explosives § 57.22601 Blasting from the surface (I-A mines... blast area and through at least one atmospheric monitoring sensor. (b) After blasting, if the...

  5. 30 CFR 57.22605 - Blasting from the surface (V-A mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Blasting from the surface (V-A mines). 57.22605... Standards for Methane in Metal and Nonmetal Mines Explosives § 57.22605 Blasting from the surface (V-A mines). (a) All development and production blasting shall be initiated from the surface after all persons...

  6. 30 CFR 57.22606 - Explosive materials and blasting units (III mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosive materials and blasting units (III... materials and blasting units (III mines). (a) Mine operators shall notify the appropriate MSHA District Manager of all nonapproved explosive materials and blasting units to be used prior to their use....

  7. 77 FR 58173 - Proposed Extension of Existing Information Collection; Explosive Materials and Blasting Units...

    Science.gov (United States)

    2012-09-19

    ... Materials and Blasting Units (Pertains to Metal and Nonmetal Underground Mines Deemed To Be Gassy AGENCY... materials and blasting units as permissible for use in the mining industry. However, since there are no permissible explosives or blasting units available that have adequate blasting capacity for some metal...

  8. Man-Made Major Hazards Like Earthquake or Explosion; Case Study, Turkish Mine Explosion (13 May 2014.

    Directory of Open Access Journals (Sweden)

    Jamileh Vasheghani Farahani

    2014-10-01

    Full Text Available In all over the world, mining is considered as a high-risk activity that is pregnant with serious disasters not only for miners, engineers, and other people into it, but also for people who live near the mines. In this article, our main purpose is to examine some major mine disasters and safety in mines and the case study is a coal mine in Turkey. Safety in mines is one of the most important issues that need attention. Therefore, it is suggested that existing deficiencies in mines should be removed by continuous monitoring in all devices, equipments, control of Methane and safe separation of coal from a mine. Moreover, we recommend that early warning systems should be installed to alert some explosions, fires and other dangerous events to the fire departments, hospitals, Red Crescent and other major reliefs. Experiences from previous events in mines can help managers and miners. With some plans and projects related to disasters in mines and solution for them, some diseases such as black lung disease or other problems in mines such as carbon monoxide poisoning can forestall a danger. Before Mine owners begin their activity, they must research about the environmental and social effects of their activities. Therefore, they should identify some important hazards and determine some essential tasks to remove them or control risks via collaboration with other scientists.

  9. The consequences for children of explosive remnants of war: Land mines, unexploded ordnance, improvised explosive devices, and cluster bombs.

    Science.gov (United States)

    Watts, Hugh G

    2009-01-01

    Land mines are particularly a problem for children. The deaths and loss of body parts have been publicized, but the secondary effects - the loss or maiming of parents, the loss of physical and social space the loss of access to education, and the loss of cultivatable land with the resultant malnutrition and sickness, are less frequently considered. "Explosive Remnants of War" (ERW) is becoming the generic term to refer to land mines, unexploded ordnance, improvised explosive devices and cluster bombs. The United Nations estimates that there are currently as many as 100 million unexploded landmines with an equal number stockpiled around the world waiting to be planted. Mines are designed to be difficult to locate and their clearance is costly. Children in at least 80 countries are at risk due to ERW. The type of mine, the proximity of the child to the explosion, and location of the mine in relation to the child's body are the important determinants of the nature and severity of the injury. Children are especially susceptible to picking up explosive remnants thinking they are toys. The result is commonly loss of the hands, facial injuries, blindness and deafness. Rehabilitation for these children is extremely difficult due to remoteness and the limited resources available.

  10. Ground Truth Collection for Mining Explosions in Northern Fennoscandia and Northwestern Russia

    Energy Technology Data Exchange (ETDEWEB)

    Harris, D B; Ringdal, R; Kremenetskaya, E; Mykkeltveit, S; Rock, D W; Maercklin, N; Schweitzer, J; Hauk, T F; Lewis, J P

    2005-07-13

    We concluded comprehensive ground truth collection at the Khibiny, Olenegorsk, Kovdor, and Zapolyarnyi mines, and have basic information on 2,052 explosions. In the past two years we used this ground truth information to extract waveform data from the ARCES array and a number of regional stations (KEV, LVZ, APA) as well as from six stations that we deployed along two lines stretching between the Khibiny Massif mines and the region around the ARCES array. We calculated P/S ratios using the ARCES array data for many of these events comprising several source types (compact underground explosions, underground ripple-fired explosions, surface ripple-fired explosions). We found that the P/S ratios of small compact underground explosions in mines of the Khibiny Massif are systematically lower than the P/S ratios of large ripple-fired surface explosions. We had anticipated that smaller underground shots would appear more like single well-coupled explosions, thus having higher P/S ratios than large ripple-fired explosions. A possible explanation for this phenomenon is that the compact underground explosions in these mines are designed to fracture and drop a large quantity of ore from the ceiling of a horizontal shaft. The potential energy released by the falling ore may express as shear wave energy, which may be considerably greater than the (P wave) energy released directly by the explosive. We concluded the deployment of the six stations along the Khibiny-ARCES lines this past summer; this year we are examining the data from these stations to see how P/S ratios vary with range from the source. We have an update on the P/S ratio analysis contrasting different source types, with the addition of an analysis of range dependence using data from the temporary stations. The portable stations were redeployed in the fall of 2004 to the Kiruna and Malmberget underground mines in northern Sweden. The stations deployed in Malmberget also record events from the surface mining

  11. Ground Truth Collection for Mining Explosions in Northern Fennoscandia and Russia

    Energy Technology Data Exchange (ETDEWEB)

    Harris, D; Ringdal, F; Kremenetskaya, E; Mykkeltveit, S; Rock, D E; Schweitzer, J; Hauk, T; Lewis, J

    2004-07-15

    Analysis of data from our deployments and ground truth collection in northern Fennoscandia and northwestern Russia shows systematic variations in the P/S ratios of different types of explosions. The fact that this fundamental discriminant varies with firing practice is not in itself surprising - such variations probably contribute to the spread in P/S ratios normally observed for ripple-fired explosions. However, the nature of the variations is sometimes counterintuitive. Last year [Harris, 2003] we found that the P/S ratios of small compact underground explosions in mines of the Khibiny Massif are systematically lower than the P/S ratios of large ripple-fired surface explosions. We had anticipated that smaller underground shots would be more like single well-coupled explosions, thus having higher P/S ratios than large ripple-fired explosions. We now are performing a more extensive analysis of the data including compact and large ripple-fired explosions at additional mines and different types of explosions: small surface shots and large ripple-fired underground explosions. Our data are more complete as a result of an additional year of collection and allow a more complete sampling of the signals in range from the source. As of this writing we have measured Pn/Lg ratios on a larger number of explosions of three types: compact underground explosions, surface ripple-fired explosions and now underground ripple-fired explosions. We find that both types of underground explosions have systematically lower P/S ratios than surface ripple-fired shots; this effect is most pronounced in the 4-8 Hz frequency band. This result appears to be due to relatively diminished shear wave excitation by the surface explosions. We speculate that the relatively large shear phases in underground explosions may be caused by large amounts of rockfall in these events, which are designed to collapse the ceilings of tunnels. We have continued comprehensive ground truth collection at the Khibiny

  12. Methodical features of physical rehabilitation of victims with consequences of mine and explosive trauma

    Directory of Open Access Journals (Sweden)

    Khassan Dandash

    2016-04-01

    Full Text Available Purpose: the analysis of modern approaches to application of means and forms of physical rehabilitation of victims with mine and explosive trauma at an out-patient stage. Material & Methods: the analysis of actual special references on a problem of the mechanism of defeat, treatment and rehabilitation of consequences of mine and explosive trauma. Results: it is defined that the percent of use of nonconventional methods of non-drug therapy increases objectively and significantly in the last decade in physical rehabilitation along with a broad application of traditional complex techniques of medical physical culture, massage and physical therapy. Conclusions: kinesiotherapy, hydro-bathing technologies, reflexotherapy are most demanded in practical techniques of physical rehabilitation at mine and explosive trauma for today among methods of non-drug therapy.

  13. Prediction model of gas explosion overpressure in full-scale coal mine blind roadway

    Energy Technology Data Exchange (ETDEWEB)

    Yun-Feng Liang; Xin-Quan Zhou; Jiu-Ling Zhang; Shao Shao [China University of Mining and Technology (Beijing), Beijing (China). State Key Laboratory of Coal Resources and Safe Mining

    2009-01-15

    On the basis of the TNT equivalency method and by analysing data from gas explosion experiments, a new prediction method was put forward to estimate the attenuation of explosion overpressure in a full-scale coal mine blind roadway and its validity was testified in three cases. The results show that there is good agreement between the calculated and experimental data. 8 refs., 2 figs.

  14. Practice of Fighting Fire and Suppressing Explosion for a Super-Large and Highly Gassy Mine

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The Baijigou Mine fire in Ningxia Province, which broke out on October 24, 2003, affected more than 108 m3 of the mine and was probably the largest underground fire in China in recent years.In addition to its size, the fire was also characterized by excessive air leakage and the potential for violent methane explosions.A series of new measures were taken to fight the fire, including sealing intake tunnels with water, injecting three-phase foam through boreholes, and flushing with a large volume of nitrogen.The fire was successfully extinguished and production resumed soon afterwards; not one single methane explosion occurred during fire-fighting and afterwards.

  15. A Tale of Two Countries, Three Discriminants, and Many Mining Explosions

    Science.gov (United States)

    Arrowsmith, M.; Arrowsmith, S.; Stump, B.; Hedlin, M.

    2008-12-01

    With the advent of not only the IMS, but the contribution of high-quality stations and networks throughout the globe, nuclear explosion monitoring strategies have shifted from teleseismic to regional scales. At regional distances, the event detection threshold is greatly decreased, meaning mining explosions must be included in the event identification process. The addition of this event class leads to several questions which much be addressed in the discrimination process: (1) can delay-fired mining explosions be discriminated from earthquakes; (2) can the understanding of mining discriminants illuminate the explosion discrimination process in regions where there are no known nuclear explosions, and (3) are mining discriminants regionally dependent, and are there corrections to account for this dependence? To address these questions, we have assembled a database of ~2500 mining explosions and ~1300 earthquakes recorded at a number of regional stations, comprising a total of ~150,000 waveforms. The database is focused on two regions, the Western United States (WUS) and the Altai-Sayan (AS) region of Russia, which are both areas of prolific mining activity. Due to extensive collaboration with the largest coal mine in Wyoming and the nation, we have detailed shot information for ~1000 mining events, classified into six distinct blast types. We have limited information for events in the AS based upon contacts with the AS Seismological Expedition. We have applied 3 discriminants to data from 11 stations and 1 array in the WUS. The first discriminant, time- of-day (TOD), assesses the event origin time. Mining events occur between 9 am and 6 pm, while earthquakes are randomly distributed in time. The second discriminant, spectral ratios (SR), exploits differences between regional phases due to source type. Results are highly station centric, although the largest mining events separate from earthquakes that are < 250 km from the mine; as the earthquake dataset expands

  16. Explosion-assisted preparation of dispersed gold-bearing different-grade ore for selective mining

    Science.gov (United States)

    Trubachev, AI; Zykov, NV

    2017-02-01

    It is found that there are transient zones (between quality and off-quality ore areas) with the respective content of useful component in an ore body, and a variant of explosive treatment of such zones before the selective mining is put forward. Practicability of two processing technologies is evaluated: processing of high-grade and low-grade ore from the transient zones and heap leaching of metals from the low-grade and impoverished ore. Open mining technology is conventional truck-and-shovel scheme, with distributed ore flows to processing plant and (or) to heap leaching, which generally enhances the mine efficiency.

  17. Use of Diazepam to Correct Hemodynamic Changes in Explosive Mine Injury: Experimental Study

    Directory of Open Access Journals (Sweden)

    V. N. Yelsky

    2007-01-01

    Full Text Available Objective. To study the hemodynamic effect of benzodiazepine tranquilizers in explosive mine injury in an experiment.Materials and methods. The study was performed on non-inbred male rats; hemodynamic parameters were examined at the systemic, organ, and microcirculatory levels.Results. Circulatory adaptive changes occurring at the beginning of a premorbid load further become pathogenic, which in combination with a progressive change in blood-brain barrier resistance results in the severer course of premorbid load-complicated explosive mine injury than that of isolated one. Correction of occurring disorders, by stimulating the stress-limiting GABAergic system with diazepam, is most effective within the first 25 minutes after isolated explosive mine injury and within the first 15 minutes after complicated one. Conclusion. Under the conditions of deep collieries where medical aid was generally late, emergency medical activation of urgent adaptation mechanisms by the techniques specially developed by the authors for these conditions is the most effective way of preventing the complications of explosive mine injury. 

  18. The risk evaluation of mine coal-dust explosion based on BP neural network

    Institute of Scientific and Technical Information of China (English)

    CHEN Lian-jun; CHENG Wei-min

    2007-01-01

    Introduced the theory of three types of hazardous sources, and it recognized and analysed such three types of hazardous sources as the factor of inherent hazardous source, factor of inducing hazardous source and factor of men, which affect the safety and reliability of coal-dust explosion risk system and then builds up the risk factor indices of coal-dust explosion according to analysis of conditions inducing the coal-dust explosion. It fixes the risk degree of coal-dust explosion risk system by analyzing loss probability and loss scope of risk system and by means of the probabilistic hazard evaluation method and risk matrix method, etc.. According to the feature of strong capability of nonlinear approximation of BP neural network, the paper designed the structure of BP neural network for the risk evaluation of the mine coal-dust explosion with BP neural network. And the weight of the network was finally determined by training the given samples so that the risk degree of samples to be measured could be exactly evaluated and the risk of mine coal-dust explosion could be alarmed in good time.

  19. Respiratory health risks among nonmetal miners.

    Science.gov (United States)

    Short, S R; Petsonk, E L

    1993-01-01

    The risks of occupational respiratory disease faced by nonmetal miners are the focus of this review. An understanding of the respiratory risks requires an understanding of the minerology of the ground and rock around the materials being mined. Relevant exposures encompass radon gas and deisel fumes, as well as mineral and rock dusts, including free silica. The types of materials mined and their associated health effects are examined, including the silicates (fibrous silicates such as asbestos, asbestiform fibrous minerals such as wollastonite and fuller's earth, and nonfibrous silicates such as talc and kaolin), sedimentary precipitates such as phosphates, potash, gypsum, and salt, as well as hydrocarbon-containing sedimentary rock such as oil shale.

  20. The Explosively Formed Projectile (EFP) as a Standoff Sea Mine Neutralization Device

    Science.gov (United States)

    Hussain, G.; Hameed, A.; Hetherington, J. G.; Malik, A. Q.; Sanaullah, K.

    2013-04-01

    There are many methods that can be used for the clearance of underwater ammunition; for example, sea mines. In all such techniques, the primary aim is to defuse underwater ammunition without detonation. Explosively formed projectiles (EFPs) have great potential to cleanly and safely defuse underwater ammunition. Underwater simulations and experiments were conducted to highlight the use of EFPs for safe destruction of sea mines. The copper liner configuration was used to study the penetration performance of the EFPs in water. ANSYS AUTODYN-2D hydrocode was used to simulate copper EFP penetration, passage, and impact with a target immersed in water. Simulation results were obtained by making use of Lagrangian and Euler formulations. The results indicated that the velocity of an EFP reduces sharply as it enters the water. However, the velocity of an EFP is stable in the later part of its flight through the water. The results further indicated that after covering five cone diameters (CDs) in water, the velocity of the EFP was reduced below critical and it failed to perforate an aluminum target plate of 5 mm thickness. Nevertheless, it perforated the target plate at 4 CDs in water. A known quantity of high explosive sandwiched between two plates, just like explosive reactive armor (ERA), was used as a target to simulate the sea mine. Flash X-ray was also used to record the flight and penetration of the EFP through the target plate. Simulation results matched reasonably well with the experimental results.

  1. Prevention of explosion in coal mine and management of coal mine gas

    Institute of Scientific and Technical Information of China (English)

    FURUKAWA Hirofumi; LI Bingrui; TOMITA Shinji

    2009-01-01

    There are many problems in terms of safe coal production and the sound de-velopment of the coal industry. Accompanying the intensification and increasing efficiency of coal production and the conducting of mining operations at deeper and more remote areas of mines, the efficient recovery and utilization of Coal Mine Methane (CMM) is an important issue in improving and stabilizing the productivity in the coal mining industry with high levels of gas, where the incidence of gas outbursts is increasing. We plan to study various aspects of the development of production technology and characteristics of the mine site. This is to establish the technology for highly efficient coproduction coal and gas operation rate. As a result, the productivity at the coal mine face will increase due to the reduction in gas emissions in the mining face. Effective use of recovered gas can be ex-pected to reduce global warming by reducing the amount of coal mine methane gas emis-sion in the air.

  2. Earthquake-explosion discrimination using waveform cross-correlation technique for mines in southeast of Tehran

    Science.gov (United States)

    Kahbasi, A.; Moradi, A.

    2016-04-01

    The presence of man-made explosions in a seismic catalogue leads to errors in statistical analyses of seismicity. Recently, the need to monitor man-made explosions used for mining, road excavating, and other constructional applications has been become a demanding challenge for the seismologists. In this way, we gain new insight into the cross-correlation technique and conduct this approach to discriminate explosions from seismic datasets. Following this, improved P-wave arrival times are used for more precise relocation. In this study, the waveform cross-correlation technique provides a reliable means for discriminating explosions which have cross-correlation coefficients (CC) of 0.6 or greater with their own corresponding stacked waveforms. The results illustrate that approximately 80 % of seismicity of southeast of Tehran, recorded by the Iranian Seismological Center (IRSC), includes events which have cross-correlation coefficients of ≥0.6 with their corresponding stacked waveforms. Furthermore, with improved P-wave arrival time, there is a better chance to relocate explosions precisely in the region under study.

  3. DEVELOPMENT OF ANTI-PERSONNEL MINE CLEARANCE ROBOT WITH HIGH SERVICEABILITY AND MANOEUVRABILITY FOR DETECTION AND DISACTIVATION OF EXPLOSIVE OBJECTS

    Directory of Open Access Journals (Sweden)

    D. Mironov

    2012-01-01

    Full Text Available A team of the BNTU researchers has developed an anti-personnel mine clearance robot that makes it possible to detect, disactivate or transport explosive objects to safe places excluding any danger to  human life. Performance characteristics of the anti-personnel mine clearance robot  surpass foreign analogues. 

  4. RFID technology for tracking and tracing explosives and detonators in mining services applications

    Science.gov (United States)

    Mishra, P. K.; Bolic, Miodrag; Yagoub, Mustapha C. E.; Stewart, Ron F.

    2012-01-01

    The purpose of this study is to assess issues related to the usage of Radio Frequency Identification (RFID) technology for certain mining services applications. In addition, it discusses current RFID solutions and inventions related to mining services applications. Main goals of this study are to investigate if RFID technology is suitable for inventory management of detonators and boosters, security, tracing of explosives and detonators, and retrieval of the assembly from the blast debris in the event of a misfire. Attempt has been made to address the best RFID solution for the same. IEEE 1902.1(RuBee) technology may show great potential in this field since it can achieve long reading ranges and it is not affected by proximity of rocks or metals. A hybrid solution that incorporates both near-field and far-field capabilities may be reliable for reading all the boosters and detonators at predefined locations. The safety facets for using RFID with the explosives and in hazardous areas are also highlighted.

  5. Structural impairments of hippocampus in coal mine gas explosion-related posttraumatic stress disorder.

    Science.gov (United States)

    Zhang, Quan; Zhuo, Chuanjun; Lang, Xu; Li, Huabing; Qin, Wen; Yu, Chunshui

    2014-01-01

    Investigations on hippocampal and amygdalar volume have revealed inconsistent results in patients with posttraumatic stress disorder (PTSD). Little is known about the structural covariance alterations between the hippocampus and amygdala in PTSD. In this study, we evaluated the alteration in the hippocampal and amygdalar volume and their structural covariance in the coal mine gas explosion related PTSD. High resolution T1-weighted magnetic resonance imaging (MRI) was performed on coal mine gas explosion related PTSD male patients (n = 14) and non-traumatized coalminers without PTSD (n = 25). The voxel-based morphometry (VBM) method was used to test the inter-group differences in hippocampal and amygdalar volume as well as the inter-group differences in structural covariance between the ipsilateral hippocampus and amygdala. PTSD patients exhibited decreased gray matter volume (GMV) in the bilateral hippocampi compared to controls (pexplosion related PTSD had decreased hippocampal volume and structural covariance with the ipsilateral amygdala, suggesting that the structural impairment of the hippocampus may implicate in the pathophysiology of PTSD.

  6. Metal-to-nonmetal transitions

    CERN Document Server

    Hensel, Friedrich; Holst, Bastian

    2010-01-01

    This book is devoted to nonmetal-to-metal transitions. The original ideas of Mott for such a transition in solids have been adapted to describe a broad variety of phenomena in condensed matter physics (solids, liquids, and fluids), in plasma and cluster physics, as well as in nuclear physics (nuclear matter and quark-gluon systems). The book gives a comprehensive overview of theoretical methods and experimental results of the current research on the Mott effect for this wide spectrum of topics. The fundamental problem is the transition from localized to delocalized states which describes the nonmetal-to-metal transition in these diverse systems. Based on the ideas of Mott, Hubbard, Anderson as well as Landau and Zeldovich, internationally respected scientists present the scientific challenges and highlight the enormous progress which has been achieved over the last years. The level of description is aimed to specialists in these fields as well as to young scientists who will get an overview for their own work...

  7. Testing the electrostatic characteristics of polypropylene fabric with metallic yarns, intended for use in coal mines threatened by the explosion hazard. Part 2: Tests in coal mine

    Science.gov (United States)

    Talarek, M.; Orzech, L.

    2011-06-01

    The aim of this paper was to assess the electrostatic safety of polypropylene fabric with metallic yarns intended for use in coal mines. Such fabrics have not been used in the Polish mining industry yet. The tests conducted have been divided into two subgroups: laboratory tests and tests in a coal mine. This paper presents the results of tests in a coal mine, where we have focused on the resistance-to-ground in some specific situations. Bags made of fabric at the roadway face were tested, as well as the roll of fabric during transport and carried by a miner. The results obtained allow the reliable assessment of the risk of using fabrics with metallic yarns in the explosive atmosphere which often occurs in coal mines.

  8. Testing the electrostatic characteristics of polypropylene fabric with metallic yarns, intended for use in coal mines threatened by the explosion hazard. Part 2: Tests in coal mine

    Energy Technology Data Exchange (ETDEWEB)

    Talarek, M; Orzech, L, E-mail: mtalarek@komag.eu [KOMAG Institute of Mining Technology, Pszczynska 37, 44-101 Gliwice (Poland)

    2011-06-23

    The aim of this paper was to assess the electrostatic safety of polypropylene fabric with metallic yarns intended for use in coal mines. Such fabrics have not been used in the Polish mining industry yet. The tests conducted have been divided into two subgroups: laboratory tests and tests in a coal mine. This paper presents the results of tests in a coal mine, where we have focused on the resistance-to-ground in some specific situations. Bags made of fabric at the roadway face were tested, as well as the roll of fabric during transport and carried by a miner. The results obtained allow the reliable assessment of the risk of using fabrics with metallic yarns in the explosive atmosphere which often occurs in coal mines.

  9. 30 CFR 57.22401 - Underground retorts (I-A and I-B mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Underground retorts (I-A and I-B mines). 57... METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Safety Standards for Methane in Metal and Nonmetal Mines Underground Retorts § 57.22401...

  10. Underground Explosions

    Science.gov (United States)

    2015-09-09

    underground explosions has led to significant progress in the development of geomechanics a science studying mechanical properties of rocks and rock...mining industry. One way to improve methods of fragmentation by explosives involves utilizing the geomechanical properties of the rock massif, in...Geomekhanika krupnomasshtabnykh vzryvov ( Geomechanics of large explosions), Nedra, Moscow, 319 pp. [This book in available in electronic format

  11. A novel explosion-proof walking system:Twin dual-motor drive tracked units for coal mine rescue robots

    Institute of Scientific and Technical Information of China (English)

    李雨潭; 朱华; 李猛钢; 李鹏

    2016-01-01

    A new explosion-proof walking system was designed for the coal mine rescue robot (CMRR) by optimizing the mechanical structure and control algorithm. The mechanical structure innovation lies mainly in the dual-motor drive tracked unit used, which showed high dynamic performance compared with the conventional tracked unit. The control algorithm, developed based on decision trees and neural networking, facilitates autonomous switching between “Velocity-driven Mode” and “Torque- driven Mode”. To verify the feasibility and effectiveness of the control strategy, we built a self-designed test platform and used it to debug the control program; we then made a robot prototype and conducted further experiments on single-step, ramp, and rubble terrains. The results show that the proposed walking system has excellent dynamic performance and the control strategy is very efficient, suggesting that a robot with this type of explosion-proof walking system can be successfully applied in Chinese coal mines.

  12. Experiment study on the propagation laws of gas and coal dust explosion in coal mine

    Energy Technology Data Exchange (ETDEWEB)

    Rong-jun Si; Run-zhi Li; Lei Wang; Zi-ke Wu [China Coal Research Institute, Chongqing (China). Chongqing Research Institute

    2009-09-15

    An experiment of gas and coal dust explosion propagation in a single laneway was carried out in a large experimental roadway that is nearly the same with actual environment and geometry conditions. In the experiment, the time when the gas and coal dust explosion flame reaches test points has a logarithmic function relation with the test point distances. The explosion flame propagation velocity rises rapidly in the foreside of the coal dust segment and then decreases. The length of the flame area is about 2 times that of the original coal dust accumulation area. Shock wave pressure comes down to the rock bottom in the coal dust segment, then reaches a maximum peak rapidly and decreases. The theoretical basis of the research and assemble of across or explosion is supplied by the experiment conclusion. Compared with gas explosion, the force and destruction degree of a gas and coal dust explosion is much larger. 3 refs., 6 figs., 3 tabs.

  13. Experiment study on the propagation laws of gas and coal dust explosion in coal mine

    Institute of Scientific and Technical Information of China (English)

    SI Rong-jun; LI Run-zhi; WANG Lei; WU Zi-ke

    2009-01-01

    The experiment of gas and coal dust explosion propagation in a single laneway was carried out in a large experimental roadway that is nearly the same with actual envi-ronment and geometry conditions. In the experiment, the time when the gas and coal dust explosion flame reaches test points has a logarithmic function relation with the test point distances. The explosion flame propagation velocity rises rapidly in the foreside of the coal dust segment and comes down after that. The length of the flame area is about 2 times that of the original coal dust accumulation area. Shock wave pressure comes down to the rock bottom in the coal dust segment, then reaches the maximum peak rapidly and comes down. The theoretical basis of the research and assemble of across or explosion is sup-plied by the experiment conclusion. Compared with gas explosion, the force and destruc-tion degree of gas and coal dust explosion is much larger.

  14. The principle analysis of methane explosion suppressed by water column curtain in coal mining

    Institute of Scientific and Technical Information of China (English)

    ZHOU Tong-ling(周同龄); HE Xue-qiu(何学秋); YANG Yi(杨艺)

    2004-01-01

    The principles of fine water mist explosion-extinguishing system was introduced. The defects of current systems were analyzed. The concept of a new water column curtain and the explosion-extinguishing mechanism were given. Using water column curtain to suppress methane explosion in experiment pipes was conducted. The photos were written with schlieren photograph system. The results of experiment show that the effect is perfect.

  15. ECONOMIC GEOLOGY (2)NONMETALS DEPOSITS

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    <正>20071073 Huang Tiedong(No.1 Geological Team of Xinjiang Bureau of Exploration and Mining,Changji,Xinjiang 831100,China) Formation of the Salt Lake and KNO3 Ore in the Kumishi Block-Falling Basin in Xin- jiang(Hydrogeology & Engineering Geology, ISSN1000-3665,CN11-2202/P,32(6), 2005,p.20-24,4 illus.,3 tables,8 refs.) Key words:niter,salt deposits,Xinjiang The Kumishi Basin,a Cenozoic block- falling basin,has been controlled by a dry continental climate and continuously under- went a concentration process due to evapora- tion.The rock salt began to form in the late Pliocene to Pleistocene(35 ka B.P.).The thick rock salt bodies assembled in the late Holocene(4.5 ka B.P.)because of the stable crust and the continuous dry climate.With the evolution into the dry salt lake stage,the brines occurring in the crystals further con- centrated and the liquid-phase KNO3 formed,which is overlain by K-rich rock salt.

  16. Statistic analysis and prevention measures on poisoning and asphyxiation accidents in metal and nonmetal underground mines%金属非金属地下矿山中毒窒息事故统计分析与对策研究

    Institute of Scientific and Technical Information of China (English)

    杨志强; 李永密

    2015-01-01

    When we focus on the metal and nonmental mine accidents as well as the occurrence reasons during 2003~2012 ,we can conclude that poisoning choke is the main reason for that metal and nonmetal mine safety production situation is difficult to improve fundamentally .The imperfect mine ventilation system ,the chaotic ventilation safety management ,the illegal use of fire under the mine ,the nonuse of flame retardant materials and the blind rescuement are all reasons for poisoning suffocation accidents when we pay close attention to plenty of typical mine accident .For these reasons ,we accordingly put forward some specific prevention countermeasures and suggestions ,such as improving the mechanical ventilation system , equipped with self‐rescuers and poisonous and harmful gas detection equipment ,elimination of old equipment ,using non‐fire‐retardant materials ,strengthening emergency measures and so on .The practical applicability make it have guiding significance for preventing and reducing the poisoning suffocation accidents in metal and non‐mental mine .%通过对2003~2012年十年间金属非金属地下矿山事故的分析,从较大、重大事故起数、死亡人数等方面得出中毒窒息事故是制约金属非金属矿山安全生产形势根本好转的主要矛盾,通过对大量典型事故的分析,得出导致中毒窒息事故的主要原因有矿井通风系统不完善、通风安全管理混乱、井下违规动火、未使用非阻燃材料和盲目施救等,针对这些原因,相应地提出完善机械通风系统,配备自救器和有毒有害气体检测装备,淘汰老旧设备和使用非阻燃材料,并强化应急措施等防范对策和建议,具有很好的实用性,对防范和减少金属非金属矿山中毒窒息事故具有指导意义。

  17. Liquid explosives

    CERN Document Server

    Liu, Jiping

    2015-01-01

    The book drawing on the author's nearly half a century of energetic materials research experience intends to systematically review the global researches on liquid explosives. The book focuses on the study of the conception, explosion mechanism, properties and preparation of liquid explosives. It provides a combination of theoretical knowledge and practical examples in a reader-friendly style. The book is likely to be interest of university researchers and graduate students in the fields of energetic materials, blasting engineering and mining.

  18. Systems to limit coal dust and methane explosions in coal mines.

    CSIR Research Space (South Africa)

    Du Plessis, JJL

    1997-01-01

    Full Text Available In response to the need for enhanced precautionary measures to safeguard mine workers in collieries from the consequences of methane ignitions in a heading, the coal mining industry has expressed the desire for the development and testing of active...

  19. Active explosion barrier performance against methane and coal dust explosions

    National Research Council Canada - National Science Library

    J. J. L. du Plessis

    2015-01-01

    Preventing the propagation of methane or coal dust explosions through the use of active explosion-suppression systems remains one of the most underutilised explosion controls in underground coal mines...

  20. Estimated use of explosives in the mining industries of Algeria, Iran, Iraq, and Libya

    Energy Technology Data Exchange (ETDEWEB)

    Wilburn, D.R.; Russell, J.A.; Bleiwas, D.I. [and others

    1995-09-01

    This work was performed under Memorandum of Agreement B291534 Between the Lawrence Livermore National Laboratory (LLNL) and the United States Bureau of Mines. The Bureau of Mines authors are members of the Minerals Availability Field Office (MAFO) in Denver, CO, which uses an extensive network of information sources to develop and maintain the Minerals Availability database concerning mining and minerals properties worldwide. This study was initiated and directed by F. Heuze at LLNL. A previous study on the same subject had been commissioned by LLNL from the Mining Journal Research Services (MJRS) in London ,UK. Its results were integrated into this report. MJRS is shown as one of the numerous sources which were used for this work. All sources are listed in the report. This document is arranged in four sections, one for each country, in alphabetical order. Thie outline is the same for each country.

  1. Catalysis by nonmetals rules for catalyst selection

    CERN Document Server

    Krylov, Oleg V

    1970-01-01

    Catalysis by Non-metals: Rules of Catalyst Selection presents the development of scientific principles for the collection of catalysts. It discusses the investigation of the mechanism of chemosorption and catalysis. It addresses a series of properties of solid with catalytic activity. Some of the topics covered in the book are the properties of a solid and catalytic activity in oxidation-reduction reactions; the difference of electronegativities and the effective charges of atoms; the role of d-electrons in the catalytic properties of a solid; the color of solids; and proton-acid and proton-ba

  2. Preparation of ore blocks for mine leaching by reagent explosion injection

    Science.gov (United States)

    Shevchenko, YuS

    2017-02-01

    The current drilling-and-blasting operations fail to prepare intact ore body underlying a production horizon for subsequent mining and leaching. It is found that the required preparation quality is possible by means of advanced implementation of ore body discontinuity and filling of the resultant system of joints with active leaching solutions.

  3. The mineral base and productive capacities of metals and non-metals of Kosovo

    Energy Technology Data Exchange (ETDEWEB)

    Rizaj, M.; Beqiri, E.; McBow, I.; O' Brien, E.Z.; Kongoli, F. [University of Prishtina, Prishtina (Kosovo)

    2008-08-15

    All historical periods of Kosovo - Ilirik, Roman, Medieval, Turkish, and former Yugoslavian - are linked with the intensive development of mining and metallurgy. This activity influenced and still is influencing the overall position of Kosovo as a country. For example, according to a 2006 World Bank report as well as other studies, Kosovo has potential lignite resources (geological reserves) of about 1.5 billion tonnes, which are ranked fifth in the world in importance. Other significant Kosovan mineral resources include lead, zinc, gold, silver, bauxite, and uranium, and rare metals accompanying those minerals, including indium, cadmium, thallium, gallium, and bismuth. These rare metals are of particular importance in developing advanced industrial technologies. Kosovo also has reserves of high-quality non-metals, including magnesite, quartz grit, bentonite, argil, talc, and asbestos. No database exists for these non-metal reserves, and further research and studies are needed.

  4. The mineral base and productive capacities of metals and non-metals of Kosovo

    Science.gov (United States)

    Rizaj, M.; Beqiri, E.; McBow, I.; O'Brien, E. Z.; Kongoli, F.

    2008-08-01

    All historical periods of Kosovo—Ilirik, Roman, Medieval, Turkish, and former Yugoslavian—are linked with the intensive development of mining and metallurgy. This activity influenced and still is influencing the overall position of Kosovo as a country. For example, according to a 2006 World Bank report as well as other studies, Kosovo has potential lignite resources (geological reserves) of about 1.5 billion tonnes, which are ranked fifth in the world in importance. Other significant Kosovan mineral resources include lead, zinc, gold, silver, bauxite, and uranium, and rare metals accompanying those minerals, including indium, cadmium, thallium, gallium, and bismuth. These rare metals are of particular importance in developing advanced industrial technologies. Kosovo also has reserves of high-quality non-metals, including magnesite, quartz grit, bentonite, argil, talc, and asbestos. No database exists for these non-metal reserves, and further research and studies are needed.

  5. Chemical sensors for classification of mine-like objects by identification of explosives

    Energy Technology Data Exchange (ETDEWEB)

    Woodfin, R.L.

    1997-10-01

    This paper briefly describes a prototype sensor for detecting land mines placed in shallow water. An automatic system was developed which incorporates chemical concentration technology, an ion mobility spectrometer, and control and fluid movement subsystems. The system design was successfully demonstrated using laboratory instruments and equipment. Components for the portable unit, which will weigh less than 20 pounds, have been fabricated; field demonstrations will be completed by spring 1998. 4 figs.

  6. DEVELOPMENT OF CYCLOCONVERTER-IM SYSTEM FOR EXPLOSION-PROOF UNDERGROUND MINE HOIST

    Institute of Scientific and Technical Information of China (English)

    谢桂林; 赵一凡

    1990-01-01

    A recent developed Cycloconverter-IM haulage drive for underground mining is described in this paper. The control of this system is fully digitized. Six INTEL 8031 single-chip microprocessors are interconnected to perform the functions of motor speed control,cycloconverter firing , fault diagnosis,etc. The implementations of the above functions are illustrated,and also a new method called "slip feedback control" for improving power factor of cycloconverter is put forward in this paper.

  7. Experimental study of flame microstructure and propagation behavior of mine-gas explosion

    Institute of Scientific and Technical Information of China (English)

    CHEN Xian-feng; ZHANG Jian-hua; WANG Yu-jie; REN Shao-feng

    2008-01-01

    The high speed cameral and schlieren images methods were used to record the photograph of flame propagation process. Meanwhile, the ionization current probes were set up to detect the reaction intensity of the reaction zone. The characteristics of methane/air flame propagation and microstructure were analyzed in detail by the experi-mental results coupled with chemical reaction thermodynamics. The high speed schlieren image showed the transition from laminar flame to turbulence combustion. The ion current curves disclosed the reaction intensity and combustion characteristic of flame front. In the test, the particular tulip flame was formed clearly, which was induced to some extent by turbulent combustion. Based on the schlieren images and iron current result, it can be drawn that the small scale turbulence combustion also appears in laminar flame, which thickens the flame front, but makes little influence on the flame front shape. During the laminar-turbulent transition, the explosion pressure plays an important role on the flame structure change.

  8. The influence of the gaseous by-products from detonation and inert additives to explosives on the efficiency of mining rock breakdown

    Energy Technology Data Exchange (ETDEWEB)

    Komir, V.M.; Chebenko, V.N.; Napadailo, V.I.; Rodak, S.N.

    1981-01-01

    Results are given from experiments to determine the influence of inert additives to explosives on the intensity of crushing mining rock. The mechanism of the blast action during the destruction of the samples using carbonic acid and sand as the additives is examined. An analysis of the experimental results demonstrated that the disjoining action of the detonation products is the result of the determinate role of the radial cracks in increasing the radius of the zone--these waves are generated by the shock wave. The efficiency of the blast may be increased by using easily-decomposing additives in the explosive that during explosion, evaporate, and both give off a large amount of gas and decrease the temperature of the detonation products, and consequently, the intensity of heat exchange with the rock.

  9. Experimental study of flame microstructure and propagation behavior of mine-gas explosion

    Institute of Scientific and Technical Information of China (English)

    CHEN Xian-feng; ZHANG Jian-hua; WANG Yu-jie; REN Shao-feng

    2008-01-01

    The high speed cameral and schlieren images methods were used to record the photograph of flame propagation process.Meanwhile,the ionization current probeswere set up to detect the reaction intensity of the reaction zone.The characteristics ofmethane/air flame propagation and microstructure were analyzed in detail by the experi-mental results coupled with chemical reaction thermodynamics.The high speed schlieren image showed the transition from laminar flame to turbulence combustion.The ion current curves disclosed the reaction intensity and combustion characteristic of flame front.In the test,the particular tulip flame was formed clearly,which was induced to some extent by turbulent combustion.Based on the schlieren images and iron current result,it can be drawn that the small scale turbulence combustion also appears in laminar flame,which thickens the flame front,but makes little influence on the flame front shape.During the laminar-turbulent transition,the explosion pressure plays an important role on the flamestructure change.

  10. 75 FR 49429 - Metal and Nonmetal Dams

    Science.gov (United States)

    2010-08-13

    ... have constructed these structures for various purposes, such as disposing of tailings or mine waste... at small and large operations. Failures or near failures have occurred at copper, phosphate, sand and... tailings. The failure flooded eight lanes of a major highway, depositing tailings up to eight feet thick...

  11. 某煤矿瓦斯爆炸流场参数分布%Distribution of Flow Parameters in Coal Mine Gas Explosion

    Institute of Scientific and Technical Information of China (English)

    高尔新; 丁晨曦; 韩书亮; 孟莎莎; 张晓蕊

    2013-01-01

    The CFD software fluent was applied to simulate a coal mine gas explosion accident, and the propagation behavior of gas explosion wave was calculated by the numerical simulation methods. In the study, data of pressure and temperature distribution in gas fire of coal tunnel was obtained. Based on the analysis results, the cause of fatal accident was also obtained.%通过应用fluent流体软件,模拟了某矿井的一次瓦斯爆炸事故,采用数值模拟的方法对瓦斯燃烧爆炸波流动的运动规律进行了数值模拟计算,从而得出了瓦斯火灾后巷道中的压力场、温度场等分布.根据数值模拟分析结果,得出了事故人员的伤亡原因.

  12. 30 CFR 49.4 - Alternative mine rescue capability for special mining conditions.

    Science.gov (United States)

    2010-07-01

    ... parts of the mine in which miners work or travel; (4) Roadways or other openings are not supported or... to the Administrator for Coal Mine Safety and Health or the Administrator for Metal and Nonmetal Mine... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Alternative mine rescue capability for...

  13. Vibration in metal and non-metal incubators.

    Science.gov (United States)

    Youngblut, J M; Lewandowski, W; Casper, G R; Youngblut, W R

    1994-01-01

    The purpose of this study was to determine the amount of vibration transmitted to the surface of an incubator mattress. Empty incubators with metal (n = 12) and non-metal (n = 12) bases were monitored for vibration levels when the incubators were turned "off" and when they were turned "on." High levels of low-frequency vibration were detected in both types of incubators in both conditions. The metal incubators transmitted significantly less vibration to the mattress than did the non-metal incubators at several frequencies in the "off," the "on," and the "adjusted" conditions. These results suggest that infants experience significant whole-body vibration while lying in incubators.

  14. Mining

    Directory of Open Access Journals (Sweden)

    Khairullah Khan

    2014-09-01

    Full Text Available Opinion mining is an interesting area of research because of its applications in various fields. Collecting opinions of people about products and about social and political events and problems through the Web is becoming increasingly popular every day. The opinions of users are helpful for the public and for stakeholders when making certain decisions. Opinion mining is a way to retrieve information through search engines, Web blogs and social networks. Because of the huge number of reviews in the form of unstructured text, it is impossible to summarize the information manually. Accordingly, efficient computational methods are needed for mining and summarizing the reviews from corpuses and Web documents. This study presents a systematic literature survey regarding the computational techniques, models and algorithms for mining opinion components from unstructured reviews.

  15. 一种矿用防爆无轨电动胶轮车设计%Design of Mine Explosion-Proof Trackless Electric Iron Car

    Institute of Scientific and Technical Information of China (English)

    李博; 郑伟丽; 周会超

    2014-01-01

    This paper introduces the design of a mine explosion-proof electric iron car ,elaborated the structure of the vehicle ,electric control principle , high driving performance and the key technology of mechanical automatic explosion-proof shift clutch and transmission integration .After strict inspection and test ,the car has been produced and put into use .%介绍了一种煤矿用防爆电动胶轮车的设计方案。详细阐述了该车的结构、电气控制原理、高驱动性能和采用的安全型纯机械式自动换档防爆离合和传动集成关键技术。通过严格的测试和检验,该车相关技术均通过国家煤安和防爆认证,试制成功并投入生产。

  16. Past explosive outbursts of entrapped carbon dioxide in salt mines provide a new perspective on the hazards of carbon dioxide

    DEFF Research Database (Denmark)

    Hedlund, Frank Huess

    2013-01-01

    This paper reports on a source of past carbon dioxide accidents which so far has only been sporadically mentioned in the literature. Violent and highly destructive outbursts of hundreds of tons of CO2 occurred regularly, if not routinely, in the now closed salt mines of the former DDR....... The Menzengraben mine experienced an extreme outburst in 1953, possibly involving a several thousand tons of carbon dioxide. This source of accidents fills an important gap in the available carbon dioxide accident history and may provide a unique empirical perspective on the hazards of handling very large amounts...

  17. Core-Exciton Decay in Photoemission and the Nonmetal - Transition.

    Science.gov (United States)

    Zhang, Jiandi

    Ultra thin films or overlayers of materials, normally metallic in the bulk case, can exhibit nonmetallic characters. Typically, these systems undergo a nonmetal-to-metal transition with changing film density, crystalline structure, or thickness. The purpose of this thesis is to identify this electronic phase transition and to investigate the corresponding fundamental mechanisms by studying the detailed electronic structure. In particular, I attempted to look at the evolution of electronic structure in films undergoing this transition. The core -exciton decay in the resonant photoemission was probed, from both theoretical and experimental points of view, to correlate with the change of film metallicity. Resonant photoemission, combining with normal photoemission, was found to be a sensitive and successful method to identify the overlayer nonmetal-metal transition, both from static and dynamic pictures. In most of this work, we concentrate on the studies of the evolution of electronic structure of ultra thin films of divalent metals, on different crystalline surfaces. The formation of new Hg electronic states arising from the electron orbital hybridization between adjacent adatoms, the formation of quantum well states in the overlayers, and the evolution of mercury shape resonance due to 5d to epsilonf excitation, all provide indications of when mercury overlayers undergo a nonmetal to metal transition. This transition has been found to be associated the changes in adatom coordination number. On both Cu(100) and W(110), the interactions between the Hg adatoms and the substrates are very weak and the surface bonding is more like covalent bonding at low coverages. The Hg overlayers on these two surfaces resembles free-standing layers, and the metallicity of the overlayers is largely determined by the nearest neighbor interactions of Hg adatoms. Comparing Hg overlayers on Ni(111) where there exists a nonmetal to metal transition caused by the structure phase transition

  18. 30 CFR 75.1310 - Explosives and blasting equipment.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosives and blasting equipment. 75.1310... SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Explosives and Blasting § 75.1310 Explosives and blasting equipment. (a) Only permissible explosives, approved sheathed explosive units,...

  19. 30 CFR 57.22102 - Smoking (I-C mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Smoking (I-C mines). 57.22102 Section 57.22102... Methane in Metal and Nonmetal Mines Fire Prevention and Control § 57.22102 Smoking (I-C mines). (a) Persons shall not smoke or carry smoking materials, matches, or lighters underground or within 50 feet...

  20. 30 CFR 57.22213 - Air flow (III mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Air flow (III mines). 57.22213 Section 57.22213... Methane in Metal and Nonmetal Mines Ventilation § 57.22213 Air flow (III mines). The quantity of air... longwall and continuous miner sections. The quantity of air across each face at a work place shall be...

  1. Gas Explosion in Coal Mine Safety Driving Intelligent Real-time Early Warning and Monitoring System%矿井安全中掘进瓦斯爆炸实时智能预警监控系统

    Institute of Scientific and Technical Information of China (English)

    胡彦青

    2013-01-01

    我国百分之九十以上的煤矿是井工开采,在煤矿开采过程中瓦斯灾害始终是煤矿安全生产最大威胁。为了防止灾害的发生,构建煤矿安全实时智能预警监控系统,实现矿井掘进瓦斯爆炸实时智能预警功能,对于防止重、特大瓦斯灾害事故发生具有重要的意义,并且对于提高煤矿安全监控和管理水平,保障煤矿职工安全及煤炭工业可持续发展具有重要的意义。%More than ninety percent of China's coal mining, the coal mining process in safety production of coal mine gas disaster is always the biggest threat, In order to prevent disasters construction of coal mine safety intelligent real-time early warning and monitoring system, realize the gas explosion of mine heading real-time intelligent early warning function, to prevent heavy, especially big gas accidents, has the vital significance, and for improving coal mine safety monitoring and management level, ensure the work safety of coal mines and coal industry sustainable development has important significance.

  2. 初始压力对矿井可燃性气体爆炸特性的影响%Influence of initial pressure on explosion characteristics of flammable gases in coal mine

    Institute of Scientific and Technical Information of China (English)

    王华; 邓军; 葛岭梅

    2011-01-01

    采用20 L近球型爆炸反应器对不同初始压力下矿井单元及多元可燃性气体的爆炸特性进行了实验研究,并结合碰撞理论和火焰传播机理对实验结果进行了理论分析.实验结果表明:初始压力增加使可燃性气体的爆炸危险性增强,但使其到达最大爆炸超压的时间略有延长;最佳浓度与爆炸上限之间的可燃性气体较最佳浓度与爆炸下限之间的可燃性气体对初始压力更敏感;相同的初始压力下,矿井多元可燃性气体较单元可燃性气体甲烷爆炸的危险性更高,破坏性更强.%Explosion characteristics of mono-component and multi-component flammable gases in coal mine were studied by using a 20 L nearly spherical explosion reactor. The experimental results were theoretically analyzed through the collision theory and mechanism of flame propagation. The experimental results show that the explosive danger of flammable gases increases with the increase of initial pressure, but the time reaching the explosion peak overpressure is extended ;the flammable gases between optimum concentration and upper explosion limit are more sensitive to initial pressure than that between optimum concentration and lower explosion limit. The explosion risk of multi-component flammable gases is higher than that of methane under the same initial pressure and its explosion destructiveness is much stronger.

  3. Active explosion barrier performance against methane and coal dust explosions

    Institute of Scientific and Technical Information of China (English)

    J J L du Plessis

    2015-01-01

    Preventing the propagation of methane or coal dust explosions through the use of active explosion-suppression systems remains one of the most underutilised explosion controls in underground coal mines. As part of the effort to develop better technologies to safeguard mines, the use of active barrier systems was investigated at Kloppersbos in South Africa. The system is designed to meet the requirements of the European Standard (EN 14591-4 2007) as well as the Mine Safety Standardisation in the Ministry of Coal Industry, Coal Industrial l Standard of the Peoples Republic of China (MT 694-1997). From the tests conducted, it can be concluded that the ExploSpot System was successful in stopping flame propagation for both methane and methane and coal dust hybrid explosions when ammonium phosphate powder was used as the suppression material. The use of this barrier will provide coal mine management with an additional explosion control close to the point of ignition and may find application within longwall faces further protecting mines against the risk of an explosion propagating throughout a mine.

  4. [A case of carbon monoxide poisoning by explosion of coal mine presenting as visual agnosia: re-evaluation after 40 years].

    Science.gov (United States)

    Takaiwa, Akiko; Yamashita, Kenichiro; Nomura, Takuo; Shida, Kenshiro; Taniwaki, Takayuki

    2005-11-01

    We re-evaluated a case of carbon monoxide poisoning presenting as visual agnosia who had been injured by explosion of Miike-Mikawa coal mine 40 years ago. In an early stage, his main neuropsychological symptoms were visual agnosia, severe anterograde amnesia, alexia, agraphia, constructional apraxia, left hemispatial neglect and psychic paralysis of gaze, in addition to pyramidal and extra pyramidal signs. At the time of re-evaluation after 40 years, he still showed visual agnosia associated with agraphia and constructional apraxia. Concerning visual agnosia, recognition of the real object was preserved, while recognition of object photographs and picture was impaired. Thus, this case was considered to have picture agnosia as he could not recognize the object by pictorial cues on the second dimensional space. MRI examination revealed low signal intensity lesions and cortical atrophy in the bilateral parieto-occipital lobes on T1-weighted images. Therefore, the bilateral parieto-occipital lesions are likely to be responsible for his picture agnosia.

  5. A case of carbon monoxide poisoning by explosion of coal mine presenting as visual agnosia: re-evaluation after 40 years

    Energy Technology Data Exchange (ETDEWEB)

    Takaiwa, A.; Yamashita, K.; Nomura, T.; Shida, K.; Taniwaki, T. [Kyushu University, Fukuoka (Japan). Department of Neurology, Graduate School of Medical Science

    2005-11-15

    We re-evaluated a case of carbon monoxide poisoning presenting as visual agnosia who had been injured by explosion of Miike-Mikawa coal mine 40 years ago. In an early stage, his main neuropsychological symptoms were visual agnosia, severe anterograde amnesia, alexia, agraphia, constructional apraxia, left hemispatial neglect and psychic paralysis of gaze, in addition to pyramidal and extra pyramidal signs. At the time of re-evaluation after 40 years, he still showed visual agnosia associated with agraphia and constructional apraxia. Concerning visual agnosia, recognition of the real object was preserved, while recognition of object photographs and picture was impaired. Thus, this case was considered to have picture agnosia as he could not recognize the object by pictorial cues on the second dimensional space. MRI examination revealed low signal intensity lesions and cortical atrophy in the bilateral parieto-occipital lobes on T1-weighted images. Therefore, the bilateral parieto-occipital lesions are likely to be responsible for his picture agnosia.

  6. [Carbon monoxide poisoning: clinical features of the victims of the explosion accident of Mitsui-Miike Mikawa coal mine 50 years ago].

    Science.gov (United States)

    Kato, Motohiro

    2015-01-01

    Clinical features of carbon monoxide poisoning have been described in 24 victims of an intense explosion accident of the Mitsui-Miike Mikawa coal mine in Japan 50 years ago; these victims were admitted to the Kyushu University Hospital as they suffered from severe poisoning. In the early stage of poisoning, all victims showed disturbed state of consciousness, varying in duration from 5.5 hours to 3 months, and the duration of unconsciousness was closely correlated to the clinical severity in the late stage. Some of the severely poisoned patients showed a transient stage of apallic syndrome. After recovery from unconsciousness, all patients presented with severe amnestic syndrome and loss of initiative. Neurologically, the extrapyramidal signs were prominent in the early stage, which gradually improved in the late stage. Variable types of agnosia and apraxia were apparent in some of the severely and moderately poisoned patients in the late stage, with prominent Gerstmann syndrome and visual-visuospatial agnosias. Since these signs showed poor improvement, the agnosia and apraxia, as well as impaired intellectual ability, remained as a sequela of the poisoning, and were one of the major causes of deficits of the patients in their daily life activities in the late stage.

  7. Three Dimension Temperature Field Studies of Mine Explosion-Proof Motor%矿用防爆电机三维温度场研究

    Institute of Scientific and Technical Information of China (English)

    郑国丽; 黄鹏程

    2012-01-01

    电机温升对电机的性能有重要影响,是电机设计的关键.基于流体动力学原理,对矿用防爆电机的热流耦合场进行数值计算,得到了电机内部流场特性、电机整体温度分布、电机各部件峰值温度及所在位置.通过方案比较,确定定、转子铁心长度;然后进行结构优化,采用电机内置风扇、定转子铁心增设通风孔两种方法增强电机内部冷却效果,并验证数值计算的可行性.所得结论为电机设计提供了一定的理论参考.%It was the key of motor design because that the motor temperature rise has a significant effect on performance of the electric motors. Thermal-fluid coupled field of mine explosion-proof motor was numerically calculated based on computational fluid dynamics principles. Characteristic of flow field inside the motor, the overall temperature distribution of motor, peak temperature and peak temperature location of motor parts were obtained. Firstly, determine the length of the stator and rotor core by the comparison of proposals. Secondly, optimize the structure according to the temperature distribution, and the motor cooling effect was improved by the method of installing the fan inside the motor and adding vents to the core of stator and rotor. Finally, verify the feasibility of the numerical calculation. The conclusion would provide theoretical references for motor design.

  8. Explosives tester

    Science.gov (United States)

    Haas, Jeffrey S [San Ramon, CA; Howard, Douglas E [Livermore, CA; Eckels, Joel D [Livermore, CA; Nunes, Peter J [Danville, CA

    2011-01-11

    An explosives tester that can be used anywhere as a screening tool by non-technical personnel to determine whether a surface contains explosives. First and second explosives detecting reagent holders and dispensers are provided. A heater is provided for receiving the first and second explosives detecting reagent holders and dispensers.

  9. 30 CFR 75.1315 - Boreholes for explosives.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Boreholes for explosives. 75.1315 Section 75... HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Explosives and Blasting § 75.1315 Boreholes for explosives. (a) All explosives fired underground shall be confined in boreholes except— (1) Sheathed...

  10. 30 CFR 75.1311 - Transporting explosives and detonators.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Transporting explosives and detonators. 75.1311... SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Explosives and Blasting § 75.1311 Transporting explosives and detonators. (a) When explosives and detonators are to be transported underground...

  11. 防爆变频器在煤矿应用中的关键技术%Key Technologies of Explosion-proof Frequency Converter Applied in Coal Mine

    Institute of Scientific and Technical Information of China (English)

    祝龙记; 张旭立

    2012-01-01

    分析了防爆变频器在煤矿井下使用过程中存在的电压等级、散热、电磁兼容性、逆变器转换效率等问题,详细介绍了解决这些问题的方法,即通过采用隔爆兼本质安全型技术和热管散热技术解决变频器的防爆和散热问题,使防爆变频器具有性能高、功能强、噪音低等特点;通过改变变频器的电路拓扑结构、改进控制策略等技术手段解决变频器的电磁兼容性和能耗问题,使防爆变频器满足煤矿生产的现代化要求.%The paper analyzed problems of voltage level, heat dissipation, EMC and conversion efficiency of inverter existed in using process of explosion-proof frequency converter in coal mine underground, and introduced methods of solving these problems in details, namely using technologies of flameproof and intrinsic safety and heat dissipation with heat pipes to solve problems of explosion-proof and heat dissipation of frequency converter, which can make explosion-proof frequency converter has characteristics of high performance, strong functions and low noise; using technical means of changing circuit topology and improving control strategy of frequency converter to solve problems of EMC and energy consumption of frequency converter, which can make explosion-proof frequency converter meet with requirements of modernization of coal mine production.

  12. 30 CFR 57.22105 - Smoking and open flames (IV mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Smoking and open flames (IV mines). 57.22105... Standards for Methane in Metal and Nonmetal Mines Fire Prevention and Control § 57.22105 Smoking and open flames (IV mines). Smoking or open flames shall not be permitted in a face or raise, or during release...

  13. 30 CFR 57.22104 - Open flames (I-C mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Open flames (I-C mines). 57.22104 Section 57.22104 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... mine opening is covered. The cover shall be a substantial material, such as metal or wood, topped...

  14. 30 CFR 57.4760 - Shaft mines.

    Science.gov (United States)

    2010-07-01

    ..., but without an insulation core, are acceptable if an automatic sprinkler or deluge system is installed... HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Fire Prevention and Control... following means to control the spread of fire, smoke, and toxic gases underground in the event of a...

  15. Research of auto-sealing device for coal mine explosion protection door and cover%矿井防爆门、盖自动封堵装置研发

    Institute of Scientific and Technical Information of China (English)

    董腾; 王海桥; 张永青; 柳光磊

    2012-01-01

    Explosion protection door and cover would be damaged if gas and dust exploded in coal mine underground , which caused air escape branch from main draught fan, ventilation system underground air chaos and invalid, poison gas diffusion, mash gas accumulation and caused secondary explosion. In order to reduce the loss and disaster consequence, maintain continuous regular ventilation underground after the disasters to improve the condition for survive and save, an auto-sealing device was designed. It could seal the coal mine ventilation shaft instead of explosion protection door and cover automatic and timely. When the sensor, which was set below the explosion-proof covers, sense the non-normal work state of the explosion-proof covers, it will produce the trigger signal, which will trigger the circuit control system and let it start the inflatable power equipment. The folded body of the sealing airbag will pop-up storage cavern under the control of inflated power. It will roll and expand along the support structure, fill the entire wellbore cross-section soon through the effect of the inflatable inflation and negative pressure which is created by main fan ventilation.%煤矿井底发生煤尘瓦斯爆炸事故时产生的冲击波会冲开风井防爆门、盖,引起主风机风流短路,井底风流紊乱、通风系统瘫痪,导致毒害气体扩散、瓦斯积聚,引发二次爆炸.为了减少因此造成的损失,研发了一种在防爆门、盖被摧毁后能自动封堵的装置,通过感应防爆门盖的损毁信号控制充气动力设备对气囊折叠体进行充气,折叠体被充气弹出储藏硐室,沿支撑架构延展、膨胀并充满井筒横截面,实施对风井的密封,以维持灾后井底持续通风,降低灾害后果,为井底幸存人员的生存与自救提供有利条件.

  16. Modified Coward diagram method for determining mine gas explosibility%用改进的科沃德爆炸图确定矿井瓦斯的爆炸性

    Institute of Scientific and Technical Information of China (English)

    刘通; 白子明; 戚凯旋; 刘凯; 彭敏; 程健维

    2015-01-01

    为了改良用于测定矿井瓦斯爆炸性的科沃德爆炸图,并提高其精度,从分析矿井中气体组成入手,剖析影响可燃气体爆炸极限的种种因素,对爆炸极限进行修正。研究工作取得的进展有:扩充了原来的科沃德爆炸图;纠正了可燃极限;重新定义了每一种可燃气体的鼻限点;开发了一个方程用于测算单种可燃气体所需的过量惰性气体,并运用交叉验证的方法来检验结果。结果表明,改进的科沃德爆炸性图更精准、可靠,可以应用于生产实践。%To modify the Coward diagram which is used to determine the explosibility of mine gas and improve its accuracy,the study began with the analysis of mine gas composition and analyzed various influencing factors on flammable gas explosion limit, meanwhile corrected the explosion limit.Improvements that conducted in this research including:expanding the original Coward diagram;correcting the original flammable limits;redefining the nose limit for each combustible gas;and developing an equation to predict the excessive amount of inert gas needed for each combustible gas,then cross-verification method is used to test the re-sults.The results show that the modified Coward diagram method has higher accuracy and reliability and could be applied in prac-tice.

  17. MINING IN ECONOMY OF REPUBLIC OF CROATIA

    OpenAIRE

    Željko Matiša

    1996-01-01

    Croatia is not especially rich in mineral ore resources, and therefore it cannot be included into "mining countries". Nevertheless since exploitation of mineral resources is a primary activity in economy of any country, mining in Croatia is given a great significance. In Croatia, research and exploitation of oil and gas is considered to be the most significant. Exploitation of mineral resources for production of metals is negligable, while esploitation of non-metals satisfies the majority ...

  18. Occurrence, emission and ignition of combustible strata gases in Witwatersrand gold mines and Bushveld platinum mines, and means of ameliorating related ignition and explosion hazards, Part 1: literature and technical review.

    CSIR Research Space (South Africa)

    Cook, AP

    1998-10-01

    Full Text Available on different mines. Gold mines have more ignition related accidents, whereas the platinum mines have face outbursts during drilling, usually without ignition. The most common causes leading to gas accidents are changes to the ventilation, lack of testing... Plessis, 1998). It accumulates in raises and other high areas, layering in poor ventilation (Rowe, 1998), and this can lead to long tailing layers extending along the hangingwall. The pressure of gas pockets causes the face to break out (Marais, 1998...

  19. 高能炸药扫雷可行性计算分析%Calculation and Analysis on Feasibility of Clearing Mines Using High Energy Explosive

    Institute of Scientific and Technical Information of China (English)

    郭迎春; 侯吉忠

    2009-01-01

    炸药所能释放的能量多少通常取决于其密度和爆轰波速度,爆热的大小直接影响炸药对地雷的扫雷效果,针对多种高能炸药的不同特点,以扫雷需求为牵引,进行了炸药的扫雷原理分析和扫雷应用的计算,为扫雷试验研究和新型扫雷器材的开发提供参考.%The quantity of energy that explosive can release usually depends on the density and the speed of detonation wave. The blasting heat will directly influence the mineclearing effect of explosive. Aiming at different characteristics of various high energy explosive, and on the basis of mineclearing requirements, the mineclearing principle of explosive is analyzed and the mineclearing application of explosive is calculated. The results can be the reference for mineclearing test research and developing new mineclearing equipment.

  20. Fire and explosion hazards of oil shale

    Energy Technology Data Exchange (ETDEWEB)

    1989-01-01

    The US Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles. 10 refs., 54 figs., 29 tabs.

  1. Fire and explosion hazards of oil shale

    Energy Technology Data Exchange (ETDEWEB)

    1989-01-01

    The US Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles. 10 refs., 54 figs., 29 tabs.

  2. 30 CFR 7.100 - Explosion tests.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosion tests. 7.100 Section 7.100 Mineral... Underground Coal Mines Where Permissible Electric Equipment is Required § 7.100 Explosion tests. (a) Test... agree. (ii) Remove all parts that do not contribute to the operation or ensure the...

  3. 30 CFR 19.7 - Protection against explosion hazard.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Protection against explosion hazard. 19.7..., EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC CAP LAMPS § 19.7 Protection against explosion hazard. Unless properly designed, electric cap lamps may present two sources of probable explosion...

  4. 30 CFR 77.1303 - Explosives, handling and use.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosives, handling and use. 77.1303 Section... MINES Explosives and Blasting § 77.1303 Explosives, handling and use. (a) Persons who use or handle... treated and handled with the same safety precautions as blasting caps and electric detonators. (o) Capped...

  5. Absorbed dose assessment in particle-beam irradiated metal-oxide and metal-nonmetal memristors

    Directory of Open Access Journals (Sweden)

    Knežević Ivan D.

    2012-01-01

    Full Text Available Absorbed dose was estimated after Monte Carlo simulation of proton and ion beam irradiation on metal-oxide and metal-nonmetal memristors. A memristive device comprises two electrodes, each of a nanoscale width, and a double-layer active region disposed between and in electrical contact with electrodes. Following materials were considered for the active region: titanium dioxide, zirconium dioxide, hafnium dioxide, strontium titanium trioxide and galium nitride. Obtained results show that significant amount of oxygen ion - oxygen and nonmetal ion - nonmetal vacancy pairs is to be generated. The loss of such vacancies from the device is believed to deteriorate the device performance over time. Estimated absorbed dose values in the memristor for different constituting materials are of the same order of magnitude because of the close values of treshold displacement energies for the investigated materials.

  6. Instrument safety in explosive atmospheres.

    Science.gov (United States)

    Bossert, J A

    1975-01-01

    The current "Energy Crisis" has dramatically increased our potential need for coal, the worlds most abundant fossil fuel. This will probably lead to a greater use of automation and instrumentation in the coal mining industry. The presence of methane in coal mines and in the coal itself plus the presence of coal dust, both of which can form an explosive atmosphere in air, means that the possibility of a gas or coal dust ignition must be considered when designing, purchasing and installing new equipment in this industry. In addition, many metallurgical processes involve the use of potentially explosive substances against which similar safety precautions must be taken. This paper outlines the various methods of protection currently in use and proposed for electrical instruments in explosive atmospheres, with particular emphasis on the work of the International Electrotechnical Commission.

  7. Application of Mine Explosion-proof Rubber-tyred Vehicle Scheduling Management System in Baijigou Well%矿用防爆胶轮车调度管理系统在白芨沟井的应用

    Institute of Scientific and Technical Information of China (English)

    翟昆志

    2015-01-01

    The auxiliary transportation system of Baijigou Well of Rujigou Anthracite Branch, Shenhua Ningx⁃ia Coal Industry Group is given priority to explosion-proof trackless rubber-tyred vehicle. This thesis mainly introduces to the dispatching management system, which is constructed for explosion-proof rubber-tyred vehi⁃cle transportation in Baijigou Well, and its main function and conceives of improvement for mine vehicle management, driver management and assignment of vehicle tasks and tracking.%神华宁煤集团汝箕沟无烟煤分公司白芨沟井辅助运输系统以防爆无轨胶轮车为主。本文主要介绍白芨沟井为防爆胶轮车运输而建设的调度管理系统,及其为矿井的车辆管理、司机管理和出车任务分派与跟踪发挥的主要作用和改进设想。

  8. 30 CFR 77.1909 - Explosives and blasting; use of permissible explosives and shot-firing units.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosives and blasting; use of permissible explosives and shot-firing units. 77.1909 Section 77.1909 Mineral Resources MINE SAFETY AND HEALTH... blasting; use of permissible explosives and shot-firing units. Except as provided in § 77.1909-1,...

  9. 30 CFR 56.6131 - Location of explosive material storage facilities.

    Science.gov (United States)

    2010-07-01

    ... MINES Explosives Storage § 56.6131 Location of explosive material storage facilities. (a) Storage... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Location of explosive material storage facilities. 56.6131 Section 56.6131 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF...

  10. 30 CFR 18.80 - Approval of machines assembled with certified or explosion-proof components.

    Science.gov (United States)

    2010-07-01

    ... or explosion-proof components. 18.80 Section 18.80 Mineral Resources MINE SAFETY AND HEALTH... MINE EQUIPMENT AND ACCESSORIES Machines Assembled With Certified or Explosion-Proof Components, Field... assembled with certified or explosion-proof components. (a) A machine may be a new assembly, or a...

  11. 煤矿井底爆炸对通风系统的破坏及及其危害%Destruction to ventilation system from mine explosion and its hazards

    Institute of Scientific and Technical Information of China (English)

    董腾; 王海桥; 陶伟; 陈世强; 吴涛

    2012-01-01

    After explosion of the coal mine underground, the ventilation system will be damaged. In order to study the harm because of no wind, it is analyzed the specific damage situation of the ventilation system which involved the tunnel underground , electrical equipments , dampers and pipeline, studied the new risk factors and harmful consequences without wind. Causing no wind in the underground well, analyzed the risk factors include smoke flowing disorders, rising gas density, declining oxygen concentration, expanding the disaster area, and even lead to second explosion and other dangers. The result showed that the coal mine should be maintained continue to ventilate, develop necessary facility to avoid airflow short, which could decrease the casualties after an gas explosion, before the personnel inclined safely.%为了研究煤矿井下发生爆炸后因通风系统受损停风而造成的危害,分析了爆炸冲击波对井下巷道、电气设备、风门管道等通风系统的具体损毁情况,探讨了防爆井盖被冲开后导致风流短路的危害,研究了因停风而导致井下烟流紊乱、有害气体和瓦斯浓度升高、灾害区域扩散蔓延、氧气浓度下降、甚至引发二次爆炸等各种危险因素及灾害后果.结果表明:在煤矿发生爆炸后人员未全部安全升井前应保持持续通风,应开发出必要的设备防止井下风流短路,从而减少爆炸事故造成的伤亡人数,降低灾害后果.

  12. 煤矿瓦斯爆炸阻隔爆技术现状及展望%Status quo and prospect of gas explosion suppressing and isolating techniques in coal mines

    Institute of Scientific and Technical Information of China (English)

    张如明; 何学秋; 聂百胜; 李祥春; 戴林超; 赵彩虹

    2011-01-01

    煤矿主要采用隔爆水棚或岩粉棚来抑制瓦斯爆炸火焰传播,但此类技术仅针对一次性瓦斯爆炸,而缺乏对多次及连续瓦斯爆炸的有效阻隔爆手段.仅注重对燃烧波的淬熄作用,对造成很大破坏的冲击波的衰减效果不足.多孔介质的淬熄火焰和衰减冲击波的效能已得到国内外专家的重视,实验研究了多层丝网和多孔材料如泡沫铝和泡沫陶瓷的阻隔爆效果.泡沫陶瓷作为一种多孔介质,具有开孔率大、耐高温、抗冲击力强的优点.理论分析和实验研究表明,由于壁面的多次撞击效应,多孔介质可以有效地销毁瓦斯燃烧化学反应产生的自由基数量,抑制化学反应的放热,使化学反应不能自持进行,进,淬熄燃烧火焰传播;可以大幅衰减瓦斯爆炸的冲击波强度,起到同时淬熄燃烧火焰和衰减冲击波的作用.多孔介质有望成为煤矿井下一种新型的瓦斯爆炸阻隔爆材料和方法.%At present, coal mines largely resort to water tubs or rock barriers to suppress gas explosion flame propagation , but they concentrate only on initial gas explosions, and are inadequate to suppress and isolate multiple and continuous gas explosions. Moreoever, these devices mostly focus on quenching of combustion waves, and cannot significantly attenuate shock waves responsible for enormous damage. Thanks to its excellent performance in flame propagation quenching and shock wave attenuation, porous medium has attracted the attention of specialists worldwide. They investigated the gas explosion suppression effects of multilayer mesh and porous material. Foam ceramic is characterized with large porosity and resistance against high temperature and shock force. Theoretical analysis and experimental study suggested that, due to numerous collisions with the skeletons in porous medium, the free radicals generated in the chemical reactions of gas combustion can be largely destroyed, the heat release can

  13. Landmine Detection Technologies to TraceExplosive Vapour Detection Techniques

    OpenAIRE

    2007-01-01

    Large quantity of explosive is manufactured worldwide for use in various types of ammunition,arms, and mines, and used in armed conflicts. During manufacturing and usage of the explosiveequipment, some of the explosive residues are released into the environment in the form ofcontaminated effluents, unburnt explosives fumes and vapours. Limited but uncontrolledcontinuous release of trace vapours also takes place when explosive-laden landmines are deployedin the field. One of the major technolo...

  14. Asphalt modified with nonmetals separated from pulverized waste printed circuit boards.

    Science.gov (United States)

    Guo, Jiuyong; Guo, Jie; Wang, Shifeng; Xu, Zhenming

    2009-01-15

    Nonmetals separated from pulverized waste printed circuit boards (PCBs) were reused as a new modifier to improve the performance of asphalt. The classical and rheological properties of unmodified asphalt and non-metal-modified asphalt (NMA) were determined. Specifically, the influence of nonmetals content and particle size on these properties has been studied. When the nonmetals content was 25 wt% and the particle size group was 0.07-0.09 mm, the NMA had a viscosity of 1225 cP at 135 degrees C, a penetration of 53.7 dmm at 15 degrees C, a ring and ball softening point of 54 degrees C, a ductility of 43.5 cm at 15 degrees C, a G*/sin delta of 3995.27 Pa at 60 degrees C, and an upper limit temperature (G*/sin delta = 1 kPa) of 69.4 degrees C, all of which showed that the high temperature performance of asphalt was improved significantly. Therefore, this study gives a fundamental understanding of NMA and represents a novel attempt to deal with the fast increasing quantities of nonmetals from waste PCBs, which is significant from an environmental and economic standpoint.

  15. Synthesis and Catalytic Applications of Non-Metal Doped Mesoporous Titania

    Directory of Open Access Journals (Sweden)

    Syed Z. Islam

    2017-03-01

    Full Text Available Mesoporous titania (mp-TiO2 has drawn tremendous attention for a diverse set of applications due to its high surface area, interfacial structure, and tunable combination of pore size, pore orientation, wall thickness, and pore connectivity. Its pore structure facilitates rapid diffusion of reactants and charge carriers to the photocatalytically active interface of TiO2. However, because the large band gap of TiO2 limits its ability to utilize visible light, non-metal doping has been extensively studied to tune the energy levels of TiO2. While first-principles calculations support the efficacy of this approach, it is challenging to efficiently introduce active non-metal dopants into the lattice of TiO2. This review surveys recent advances in the preparation of mp-TiO2 and their doping with non-metal atoms. Different doping strategies and dopant sources are discussed. Further, co-doping with combinations of non-metal dopants are discussed as strategies to reduce the band gap, improve photogenerated charge separation, and enhance visible light absorption. The improvements resulting from each doping strategy are discussed in light of potential changes in mesoporous architecture, dopant composition and chemical state, extent of band gap reduction, and improvement in photocatalytic activities. Finally, potential applications of non-metal-doped mp-TiO2 are explored in water splitting, CO2 reduction, and environmental remediation with visible light.

  16. Research into Exploitation and Application of Three Sorts of Unconventional Nonmetal Resources

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In this paper the authors introduce their past years' study results about the exploitation and application of three sorts of nontraditional nonmetal minerals. In this research, the main aspects and techniques of basic study for the exploitation and application are summarized, and some key science and technological problems are proposed as the objects of their future research.

  17. The writing of 'The Westray Story': a discourse analysis of the aftermath of the Westray coal mine explosion (Nova Scotia)

    Energy Technology Data Exchange (ETDEWEB)

    Dodd, S.M. [York University (Canada). Toronto, ON (Canada). Department of Sociology

    2002-07-01

    This is a critical discourse analysis of the report of the public inquiry of the Westray mining disaster. The conflicting interests and values of the factions involved, the availability of information in the workplace, and the assignment of blame for the disaster are among the factors considered. The 'new prudentialism' that holds individuals responsible for risk assessment and avoidance, but forces them to act within the organizational framework, is discussed.

  18. Henan Plans to Shut Down Over 475 mines by 2015

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>Recently, the General Office of Henan Provin-cial Government printed and distributed "He-nan Province Metal and Non-metal Mine Recti-fication Shutdown Work Plan (2012-2015)" (The Plan). By carrying out rectification and

  19. Explosion and explosives. Volume 32, Number 5, 1971

    Energy Technology Data Exchange (ETDEWEB)

    1976-01-01

    The following topics are discussed: CMDB propellants with high pressure exponent; the thermal decomposition of phenylnitromethane in 2-propanol; double exposed flash x-ray photographic observation on detonation of coal mining explosions; detonation of condensed multiple components about detonation characteristics of three liquid explosives; synthesis of N,N'-bis (2,4,6-trinitro-3-glycidoxyphenyl)-ethylene dinitramine; resistance characteristics of electric primer containing conductive particles; and formation of Meisenheimer's complex by adding an aqueous sodium hydroxide to the reaction product of epoxy compound with picric acid.

  20. Explosion limits for combustible gases

    Institute of Scientific and Technical Information of China (English)

    TONG Min-ming; WU Guo-qing; HAO Ji-fei; DAI Xin-lian

    2009-01-01

    Combustible gases in coal mines are composed of methane, hydrogen, some multi-carbon alkane gases and other gases. Based on a numerical calculation, the explosion limits of combustible gases were studied, showing that these limits are related to the concentrations of different components in the mixture. With an increase of C4H10 and C6H14, the Lower ExplosionLimit (LEL) and Upper Explosion-Limit (UEL) of a combustible gas mixture will decrease clearly. For every 0.1% increase in C4H10 and C6H14, the LEL decreases by about 0.19% and the UEL by about 0.3%. The results also prove that, by increasing the amount of H2, the UEL of a combustible gas mixture will increase considerably. If the level of H2 increases by 0.1%, the UEL will increase by about 0.3%. However, H2 has only a small effect on the LEL of the combustible gas mixture. Our study provides a theoretical foundation for judging the explosion risk of an explosive gas mixture in mines.

  1. Injury experience in coal mining, 1990

    Energy Technology Data Exchange (ETDEWEB)

    None

    1991-01-01

    This Mine Safety and Health Administration (MSHA) informational report reviews in detail the occupational injury and illness experience of coal mining in the United States for 1990. Data reported by operators of mining establishments concerning work injuries are summarized by work location, accident classification, part of body injured, nature of injury, occupation, and anthracite or bituminous coal. Related information on employment, worktime, and operating activity also is presented. Data reported by independent contractors performing certain work at mining locations are depicted separately in this report. For ease of comparison between coal mining and the metal and nonmetal mineral mining industries, summary reference tabulations are included at the end of both the operator and the contractor sections of this report.

  2. Injury experience in coal mining, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Reich, R.B.; Hugler, E.C.

    1994-05-01

    This Mine Safety and Health Administration (MSHA) informational report reviews in detail the occupational injury and illness experience of coal mining in the United States for 1992. Data reported by operators of mining establishments concerning work injuries are summarized by work location, accident classification, part of body injured, nature of injury, occupation, and anthracite or bituminous coal. Related information on employment, worktime, and operating activity also is presented. Data reported by independent contractors performing certain work at mining locations are depicted separately in this report. For ease of comparison between coal mining and the metal and nonmetal mineral mining industries, summary reference tabulations are included at the end of both the operator and the contractor sections of this report.

  3. APPLICATION OF EXPLOSIVE ENERGY IN METALWORKING

    Directory of Open Access Journals (Sweden)

    Vječislav Bohanek

    2013-07-01

    Full Text Available When an explosive charge is detonate, considerable amount of energy in a very short period of time is released. Energy, released in this way, is used for performing various kinds of useful work. Most explosives are consumed to obtain mineral raw materials in the mining industry and for various excavations in the construction industry. One of the specific areas of application explosive energy is an area of explosive metalworking. Using energy of explosive metal is welded, formed, cuts, harden etc. This paper presents an overview of the existing explosive metalworking methods. Methods are explained and comparative advantages in comparison to conventional metalworking methods are given (the paper is published in Croatian.

  4. Protection of Military Vehicles Against Mine Threats and Improvised Explosive Devices / Ochrona Pojazdów Wojskowych Przed Wybuchem Min i Improwizowanych Urządzeń Wybuchowych

    Directory of Open Access Journals (Sweden)

    Niezgoda Tadeusz

    2015-09-01

    Full Text Available Pojazdy wojskowe są narażone na działanie m.in. fali wybuchowej min oraz improwizowanych urządzeń wybuchowych IED (z ang. improvised explosive device. Dotychczasowe rozwiązania konstrukcyjne pancerzy pojazdów wojskowych nie zapewniają ich ochrony na maksymalnym poziomie. W publikacji przedstawiono rozwiązania konstrukcyjne, których celem jest zwiększenie odporności pojazdów wojskowych na eksplozję ładunków wybuchowych. Ponadto scharakteryzowano wymagania dotyczące odporności pojazdów wojskowych na wybuch min i urządzeń IED. Przedstawiono również przykładowe wyniki badań paneli energochłonnych oraz sformułowane na ich podstawie wnioski do dalszego rozwoju konstrukcji ochronnych.

  5. Sir Humphry Davy and the coal miners of the world: a commentary on Davy (1816) 'An account of an invention for giving light in explosive mixtures of fire-damp in coal mines'.

    Science.gov (United States)

    Thomas, John Meurig

    2015-04-13

    In the period between 1815 and 1818, Sir Humphry Davy read four papers to the Royal Society and published a monograph dealing with a safety lamp for coal miners, all of which record in detail the experimental work that he carried out, with his assistant Michael Faraday, so as to determine how to prevent catastrophic accidents in coal mines by the explosion of fire-damp (methane) in the presence of a naked flame. This article describes the key experiments that he performed at the Royal Institution and some of the subsequent trials made in the coal mines of the north of England. It begins, however, with an account of Davy's prior achievements in science before he was approached for help by the clergymen and doctors in the Gateshead and Newcastle upon Tyne areas. There is little doubt that the Davy lamp, from the 1820s onwards, transformed the coal industry worldwide. It also profoundly influenced the science of combustion, and in the words of a pioneer in that field, W. A. Bone, FRS, 'There is no better model of logical experimental procedure, accurate reasoning, philosophical outlook and fine literary expression.' It is a remarkable fact that it took Davy essentially only two weeks from the time he was given samples of fire-damp to solve the problem and to devise his renowned miner's safety lamp. A brief account is also given of the contemporaneous invention of a safety lamp by George Stephenson, and of some of Davy's subsequent accomplishments. This commentary was written to celebrate the 350th anniversary of the journal Philosophical Transactions of the Royal Society.

  6. Land Mines (Landminen)

    Science.gov (United States)

    1978-02-02

    Probably the most sensitive area of an armored vehicle at that time was the track. Therefore, all countries endeavored to design prepared charges...of mines, for instance through improved explosives and the shaped charge principle, the basic principle of the funcion and design of antitank mines...dispersed over a large area . In most cases, the fragments are lethal up to adistance of 10 m and beyond, and cause serious injuries even at a distance of

  7. Direct imaging of explosives

    Energy Technology Data Exchange (ETDEWEB)

    Knapp, E.A.; Moler, R.B.; Saunders, A.W.; Trower, W.P. E-mail: trower@naxs.net

    2000-11-15

    Any technique that can detect nitrogen concentrations can screen for concealed explosives. However, such a technique would have to be insensitive to metal, both encasing and incidental. If images of the nitrogen concentrations could be captured, then, since form follows function, a robust screening technology could be developed. However these images would have to be sensitive to the surface densities at or below that of the nitrogen contained in buried anti-personnel mines or of the SEMTEX that brought down Pan Am 103, {approx}200 g. Although the ability to image in three-dimensions would somewhat reduce false positives, capturing collateral images of carbon and oxygen would virtually assure that nitrogenous non-explosive material like fertilizer, Melmac[reg] dinnerware, and salami could be eliminated. We are developing such an instrument, the Nitrogen Camera, which has met experimentally these criteria with the exception of providing oxygen images, which awaits the availability of a sufficiently energetic light source. Our Nitrogen Camera technique uses an electron accelerator to produce photonuclear reactions whose unique decays it registers. Clearly if our Nitrogen Camera is made mobile, it could be effective in detecting buried mines, either in an active battlefield situation or in the clearing of abandoned military munitions. Combat operations require that a swathe the width of an armored vehicle, 5 miles deep, be screened in an hour, which is within our camera's scanning speed. Detecting abandoned munitions is technically easier as it is free from the onerous speed requirement. We describe here our Nitrogen Camera and show its 180 pixel intensity images of elemental nitrogen in a 200 g mine simulant and in a 125 g stick of SEMTEX. We also report on our progress in creating a lorry transportable 70 MeV electron racetrack microtron, the principal enabling technology that will allow our Nitrogen Camera to be deployed in the field.

  8. Direct imaging of explosives.

    Science.gov (United States)

    Knapp, E A; Moler, R B; Saunders, A W; Trower, W P

    2000-01-01

    Any technique that can detect nitrogen concentrations can screen for concealed explosives. However, such a technique would have to be insensitive to metal, both encasing and incidental. If images of the nitrogen concentrations could be captured, then, since form follows function, a robust screening technology could be developed. However these images would have to be sensitive to the surface densities at or below that of the nitrogen contained in buried anti-personnel mines or of the SEMTEX that brought down Pan Am 103, approximately 200 g. Although the ability to image in three-dimensions would somewhat reduce false positives, capturing collateral images of carbon and oxygen would virtually assure that nitrogenous non-explosive material like fertilizer, Melmac dinnerware, and salami could be eliminated. We are developing such an instrument, the Nitrogen Camera, which has met experimentally these criteria with the exception of providing oxygen images, which awaits the availability of a sufficiently energetic light source. Our Nitrogen Camera technique uses an electron accelerator to produce photonuclear reactions whose unique decays it registers. Clearly if our Nitrogen Camera is made mobile, it could be effective in detecting buried mines, either in an active battlefield situation or in the clearing of abandoned military munitions. Combat operations require that a swathe the width of an armored vehicle, 5 miles deep, be screened in an hour, which is within our camera's scanning speed. Detecting abandoned munitions is technically easier as it is free from the onerous speed requirement. We describe here our Nitrogen Camera and show its 180 pixel intensity images of elemental nitrogen in a 200 g mine simulant and in a 125 g stick of SEMTEX. We also report on our progress in creating a lorry transportable 70 MeV electron racetrack microtron, the principal enabling technology that will allow our Nitrogen Camera to be deployed in the field.

  9. 30 CFR 57.22211 - Air flow (I-A mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Air flow (I-A mines). 57.22211 Section 57.22211... Methane in Metal and Nonmetal Mines Ventilation § 57.22211 Air flow (I-A mines). The average air velocity... openings nearest the face, shall be at least 40 feet per minute. The velocity of air ventilating each...

  10. Niche explosion.

    Science.gov (United States)

    Normark, Benjamin B; Johnson, Norman A

    2011-05-01

    The following syndrome of features occurs in several groups of phytophagous insects: (1) wingless females, (2) dispersal by larvae, (3) woody hosts, (4) extreme polyphagy, (5) high abundance, resulting in status as economic pests, (6) invasiveness, and (7) obligate parthenogenesis in some populations. If extreme polyphagy is defined as feeding on 20 or more families of hostplants, this syndrome is found convergently in several species of bagworm moths, tussock moths, root weevils, and 5 families of scale insects. We hypothesize that extreme polyphagy in these taxa results from "niche explosion", a positive feedback loop connecting large population size to broad host range. The niche explosion has a demographic component (sometimes called the "amplification effect" in studies of pathogens) as well as a population-genetic component, due mainly to the increased effectiveness of natural selection in larger populations. The frequent origins of parthenogenesis in extreme polyphages are, in our interpretation, a consequence of this increased effectiveness of natural selection and consequent reduced importance of sexuality. The niche explosion hypothesis makes detailed predictions about the comparative genomics and population genetics of extreme polyphages and related specialists. It has a number of potentially important implications, including an explanation for the lack of observed trade-offs between generalists and specialists, a re-interpretation of the ecological correlates of parthenogenesis, and a general expectation that Malthusian population explosions may be amplified by Darwinian effects.

  11. Explosive Start

    Institute of Scientific and Technical Information of China (English)

    FRANCISCO; LITTLE

    2006-01-01

    I ducked involuntarily as the first set of explosions went off and made my way in double time to the street corner, where I had spotted an arcade that could be used for shelter. Running quickly in a crouched, military maneuver while inhaling gunpowder fumes, I was totally oblivious to the laughter and head-shaking coming

  12. Wireless gas sensing in South African underground platinum mines

    CSIR Research Space (South Africa)

    Abu-Mahfouz, Adnan M

    2014-04-01

    Full Text Available Approximately 70% of South African mines are classified as fiery, where methane gas potentially could cause explosions. The number of flammable gas reports and accidents are increasing steadily for both gold and platinum mines. However...

  13. 30 CFR 77.1910 - Explosives and blasting; general.

    Science.gov (United States)

    2010-07-01

    ... COAL MINES Slope and Shaft Sinking § 77.1910 Explosives and blasting; general. (a) Light and power... drill holes are being charged and until after all shots have been fired. (h) The sides of the slope...

  14. NONMETALS DEPOSITS

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    <正>20140876 Gao Junbo(College of Resources and Environmental Engineering,Guizhou University,Guiyang 550025,China);Yang Ruidong Study on the Strontium Isotopic Composition of Large Devonian Barite Deposits from Zhenning,Guizhou Province(Geochimica,

  15. NONMETALS DEPOSITS

    Institute of Scientific and Technical Information of China (English)

    2015-01-01

    20152443 Cai Yitao(Nanjing Institute of Geology and Mineral Resources,Nanjing 210016,China);Chen Guoguang Geochemical Features of the Olivine-Gabbros and Their Relationship with Diamond-Mineralization in the Langan Area,Anhui Province(Resources Survey&Environment,ISSN1671-4814,CN32-1640/N,35(4),2014,p.245-253,10illus.,3tables,44 refs.)

  16. NONMETALS DEPOSITS

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>20110947 Chen Xinglong(Guizhou Bureau of Nonferrous Metal and Nuclear Geology,Guiyang 550005,China);Gong Heqiang Endowment Factors and Development & Utilization Strategy of Bauxite Resource in North Guizhou Province(Guizhou Geology,ISSN1000-5943,CN52-1059/P,27(2),2010,p.106-110,6 refs.,with English abstract)Key words:bauxite deposit,Guizhou Province20110948 Dang Yanxia(Mineral Resource & Reservoir Evaluation Center,Urumiq 830000,China);Fan Wenjun Geological Features and a Primary Study of Metallogenesis of the Wucaiwang Zeolite Deposit,Fuyun County(Xinjiang Geology,ISSN1000-8845,CN65-1092/P,28(2),2010,p.167-170,2 illus.,1 table,5 refs.)Key words:zeolite deposit,Xinjiang Nearly all zeolite deposits in the world result from low-temperature-alteration of glass-bearing volcanic rocks.The southern slope of the Kalamali Mountain is one of the regions where medium to acid volcanics are major lithological type,thus it is a preferred area to look for zeolite deposit.The Wucaiwang zeolite ore district consists of mainly acid volcanic-clastic rocks.

  17. NONMETALS DEPOSITS

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>20111761 Chen Hua(115 Geological Party,Guizhou Bureau of Geology and Mineral Exploration & Development,Guiyang 551400,China);Deng Chao Analysis on the Metallogenic Environment of Maochang Bauxite in Guizhou Province(Guizhou Geology,ISSN1000-5943,CN52-1059/P,27(3),2010,p.198-201,2 illus.,1 table,8 refs.)Key words:bauxite deposit,Guizhou Province By long time physical and chemical process,the carbonate rock after Central Guizhou uplidft,becomes red clay,after further weathering,the red clay decomposed into the oxide,hydroxide of Al and Fe,in the dissolution hole and depression,it concentrates primary fragmentary tight and earthy karst bauxite ore.Because the variation of landform,it decomposes and cracks again,affords the material source

  18. NONMETALS DEPOSITS

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    <正>20122457 Cai Jianshe ( Fujian Institute of Geological Survey and Drawing,Fuzhou 350011,China ) On the Geologic Characteristics and Genesis of the Longtangsi Fluorite Deposit in Pucheng County,Fujian Province ( Geology of Fujian,ISSN1001-3970,CN35-1080 / P,30 ( 4 ), 2011,p.301-306,3illus.,1table,6 refs.,with English abstract ) Key words:fluorspar deposit,Fujian Province

  19. NONMETALS DEPOSITS

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    <正>20102406 Chen Gang(China University of Geosciences,Beijing 100083,China);Li Fengming Discussion on Geological Characteristics and Genesis of Yuquanshan Graphite Deposit of Xinjiang(Xinjiang Geology,ISSN1000-8845,CN65-1092/P,27(4),2009,p.325-329,4 illus.,4 tables,5 refs.)Key words:graphite deposit,XinjiangYuquanshan graphite deposit of Xinjiang occurs in mica-quartz schist of Xingeer Information which belongs to Xinditate Group of Lower Pt in Kuluketage Block of Tarim paleo-continent,and experiences two mineralizing periods of

  20. NONMETALS DEPOSITS

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>20131601 Gao Junbo(College of Resources and Environmental Engineering,Guizhou University,Guiyang 550003,China);Yang Ruidong Hydrothermal Venting-Flowing Sedimentation Characteristics of Devonian Barite Deposits from Leji,Zhenning County,Guizhou Province(Acta Sedimentologica Sinica,ISSN1000-0550,CN62-1038/P,30(3),

  1. Explosive limits and its container factors of polybasic explosive mixture gas containing H2, CH4 and CO

    Institute of Scientific and Technical Information of China (English)

    胡耀元; 李勇; 朱凯汉; 周邦智; 杨元法

    2002-01-01

    Explosive characteristics of polybasic explosive mixture gas are systematically researched. Over 28000 experimental data have been obtained from 1278 effective experiments. The paper probes into the concentration explosive limits and the container factors of polybasic explosive mixture gas which contains H2, CH4 and CO. It has worked out the sufficient and necessary condition for branch-chain explosion and the unified expression of the probability of the heterogeneous chain termination. Experiments indicate that the concentration explosive limits of polybasic explosive mixture gas (H2, CH4, CO) relate to many factors. They enlarge with the augmentability of the container (linear size, geometric shape, and flame spread direction). This will be of great significance to guiding the revision of related industrial safety targets, reclaiming and reusing related industrial tail gas and waste gas, taking precautions against the explosion hazard of mixture gas in correlated industry and mines, and applying the br

  2. 30 CFR 816.62 - Use of explosives: Preblasting survey.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Use of explosives: Preblasting survey. 816.62 Section 816.62 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE... ACTIVITIES § 816.62 Use of explosives: Preblasting survey. (a) At least 30 days before initiation of blasting...

  3. 30 CFR 817.62 - Use of explosives: Preblasting survey.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Use of explosives: Preblasting survey. 817.62 Section 817.62 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE... ACTIVITIES § 817.62 Use of explosives: Preblasting survey. (a) At least 30 days before initiation of blasting...

  4. 30 CFR 18.42 - Explosion-proof distribution boxes.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosion-proof distribution boxes. 18.42 Section 18.42 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING... and Design Requirements § 18.42 Explosion-proof distribution boxes. (a) A cable passing through...

  5. 30 CFR 18.43 - Explosion-proof splice boxes.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosion-proof splice boxes. 18.43 Section 18.43 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION... Design Requirements § 18.43 Explosion-proof splice boxes. Internal connections shall be rigidly held...

  6. 防爆抽出式对旋轴流局部通风机叶轮的静力分析%Impeller static force of extractable explosion-proof contra-rotating axial fan for mine local ventilation

    Institute of Scientific and Technical Information of China (English)

    贺秋冬; 李丽君; 李坤

    2012-01-01

    为提高矿用防爆抽出式对旋轴流局部通风机叶轮的安全可靠性,以FBDCNo9.0/2×30型通风机叶轮为研究对象,利用有限元分析软件对叶轮建立了有限元计算模型,对其应力和位移进行了计算.经测试,通风机运转平稳,无异常声响,风量为655~978m3/min,全压为412~3443Pa,静压为118~3314Pa,最高静压效率达到70.35%,最高全压效率达到74.23%,比A声级噪声为17.6dB,叶轮的强度和刚度满足要求.样机试验及现场应用表明:对该型通风机叶轮所建立的计算与分析模型正确;通过合理的设计,采用等厚圆弧板叶型、普通热轧低碳钢板材质作叶片的对旋轴流叶轮,其强度、刚度能够满足要求,整机的空气动力性能较好.%To improve the impeller safe reliability of extractable explosion-proof contra-rotating axial fan for mine local ventilation, extractable explosion-proof contra-rotating axial fan for mine local ventilation FBDCNo9. 0/2 × 30(impeller diameter of 0.9 m, 2 stages, single stage power of 30 KW) was taken as the research object, and an approximate three-dimensional finite element compulation model is built by using ANSYS software. The stress and the displacement were calculated, too. By testing, the fan works stably without unusual sound. The air quantity is 655 -978 m3/min, total pressure is 3443 -412 Pa, static pressure is 3314 - 118 Pa. And the highest static pressure efficiency is up to 70. 35% , the highest total pressure efficiency is also up to 74. 23% , a-weight specific sound level is 17. 5 dB. Furthermore, the intension and stiffness of the impeller meet requirements. Sample test and field using show that the computation and the model of this impeller are right, through reasonable design, the impeller of contra-rotating axial fan with equally-thick circular arc blade profile and common hot-rolling low-carbon steel blades has the intension and the stiffness which meet demands, and the air performance

  7. Design of Explosion-proof Non-central Switch Voice Communication System in Coal Mine%煤矿井下防爆型无主机语音通信系统设计

    Institute of Scientific and Technical Information of China (English)

    夏春华

    2012-01-01

    An explosion-proof non-central switch voice communication systems is introduced in this article for the disadvantage of the slow rate of communication, the small bandwidth, the bad tone and the big SNR. The system consist of high voice encode and de- code chip CMX618 based on Robust Advanced Low Complexity Waveform Interpolation. The main system adopts the low power STM32FI03RE controller and the communication bus of far distance uses the CAN bus. Experimental results indicate that the tone of the system is acceptable better and the stability and reliability of the system is good when the compression rate mode is 2400b/s. The designed system can satisfy the demand of voice communication bandwidth, the quality of voice, the system stability and reliability. It can be Popularized in the coal mine.%针对煤矿井下语音通信速率低,带宽小,音质差,噪声大等缺点,设计了一种煤矿井下防爆型低功耗无主机语音通信系统。该系统的语音编解码采用高压缩率算法RALCWI的CMX618,系统控制采用低功耗STM32F103RE控制器,语音的远距离通信采用CAN总线方式。试验结果表明,语音的压缩速率模式2400b/s时,音质较好,通信稳定可靠,满足煤矿井下语音通信带宽要求,语音质量,系统稳定与可靠性高的要求,易于在煤矿系统中推广。

  8. Explosive Pleuritis

    Directory of Open Access Journals (Sweden)

    Jasdeep K Sharma

    2001-01-01

    Full Text Available The objective of the present paper is to describe the clinical and computed tomography features of 'explosive pleuritis', an entity first named by Braman and Donat in 1986, and to propose a case definition. A case report of a previously healthy, 45-year-old man admitted to hospital with acute onset pleuritic chest pain is presented. The patient arrived at the emergency room at 15:00 in mild respiratory distress; the initial chest x-ray revealed a small right lower lobe effusion. The subsequent clinical course in hospital was dramatic. Within 18 h of admission, he developed severe respiratory distress with oxygen desaturation to 83% on room air and dullness of the right lung field. A repeat chest x-ray, taken the morning after admission, revealed complete opacification of the right hemithorax. A computed tomography scan of the thorax demonstrated a massive pleural effusion with compression of pulmonary tissue and mediastinal shift. Pleural fluid biochemical analysis revealed the following concentrations: glucose 3.5 mmol/L, lactate dehydrogenase 1550 U/L, protein 56.98 g/L, amylase 68 U/L and white blood cell count 600 cells/mL. The pleural fluid cultures demonstrated light growth of coagulase-negative staphylococcus and viridans streptococcus, and very light growth of Candida albicans. Cytology was negative for malignant cells. Thoracotomy was performed, which demonstrated a loculated parapneumonic effusion that required decortication. The patient responded favourably to the empirical administration of intravenous levofloxacin and ceftriaxone, and conservative surgical methods in the management of the empyema. This report also discusses the patient's rapidly progressing pleural effusion and offers a potential case definition for explosive pleuritis. Explosive pleuritis is a medical emergency defined by the rapid development of a pleural effusion involving more than 90% of the hemithorax over 24 h, which causes compression of pulmonary tissue and

  9. CSIR: Mining Technology annual review 1996/97

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    CSIR: Mining Technology works in close collaboration and strategic partnership with the mining industry, government institutions and employee organizations by acquiring, developing and transferring technologies to improve the safety and health of their employees, and to improve the profitability of the mining industry. The annual report describes achievements over the year in the areas of: rock engineering (including rockburst control, mine layout, stope and gully support, coal mining); environmental safety and health on topics such as occupational hygiene services, methane explosions, blasting techniques; and mining systems (orebody information, hydraulic transport mine mechanization, engineering design and automation, mine services). A list of Mining Technology`s 1996/97 publications is given.

  10. Explosive Pleuritis

    Directory of Open Access Journals (Sweden)

    Satish Kumar

    2012-01-01

    Full Text Available Pleural effusions associated with pneumonia (parapneumonic effusions are one of the most common causes of exudative pleural effusions in the world. Approximately 20 to 40% of patients hospitalized with pneumonia will have an accompanying pleural effusion. The term 'Explosive pleuritis' was originally described by Braman and Donat in 1986 as pleural effusions developing within hours of admission. We report a 38 years old male patient with minimal pleural effusion which progressed rapidly within one day to involve almost whole of the hemithorax. There were multiple loculations on ultrasonography of thorax. Pleural fluid was sero-sanguinous and revealed gram positive diplococcic. The patient improved with antibiotics and pigtail catheter drainage.

  11. 30 CFR 57.22212 - Air flow (I-C, II-A, and V-A mines).

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Air flow (I-C, II-A, and V-A mines). 57.22212... Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22212 Air flow (I-C, II-A, and V-A mines). Air flow across each working face shall be sufficient to carry away any accumulation of methane,...

  12. 30 CFR 15.32 - Tolerances for weight of explosive, sheath, wrapper, and specific gravity.

    Science.gov (United States)

    2010-07-01

    ..., wrapper, and specific gravity. 15.32 Section 15.32 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... explosive, sheath, wrapper, and specific gravity. (a) The weight of the explosive, the sheath, and the outer.... (c) The specific gravity of the explosive and sheath shall be within ±7.5 percent of that specified...

  13. 30 CFR 75.1312 - Explosives and detonators in underground magazines.

    Science.gov (United States)

    2010-07-01

    ... magazines. 75.1312 Section 75.1312 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF... Blasting § 75.1312 Explosives and detonators in underground magazines. (a) The quantity of explosives kept..., explosives and detonators taken underground shall be kept in— (1) Separate, closed magazines at least 5...

  14. Leidenfrost explosions

    CERN Document Server

    Moreau, F; Dorbolo, S

    2012-01-01

    We present a fluid dynamics video showing the behavior of Leidenfrost droplets composed by a mixture of water and surfactant (SDS, Sodium Dodecyl sulfate). When a droplet is released on a plate heated above a given temperature a thin layer of vapor isolates the droplet from the plate. The droplet levitates over the plate. This is called the Leidenfrost effect. In this work we study the influence of the addition of a surfactant on the Leidenfrost phenomenon. As the droplet evaporates the concentration of SDS rises up to two orders of magnitude over the Critical Micelle Concentration (CMC). An unexpected and violent explosive behavior is observed. The video presents several explosions taken with a high speed camera (IDT-N4 at 30000 fps). All the presented experiments were performed on a plate heated at 300{\\deg}C. On the other hand, the initial quantity of SDS was tuned in two ways: (i) by varying the initial concentration of SDS and (ii) by varying the initial size of the droplet. By measuring the volume of th...

  15. Explosive Formulation Pilot Plant

    Data.gov (United States)

    Federal Laboratory Consortium — The Pilot Plant for Explosive Formulation supports the development of new explosives that are comprised of several components. This system is particularly beneficial...

  16. Ground Truth Collections for Explosions in Northern Fennoscandia and Russia

    Energy Technology Data Exchange (ETDEWEB)

    Harris, D B; Ringdal, F; Kremenetskaya, E; Mykkeltveit, S; Schweitzer, J.; Hauk, T; Asming, V; Rock, D; Lewis, P

    2003-07-28

    This project is providing ground-truth information on explosions conducted at the principal mines within 500 kilometers of the ARCES station, and is assembling a seismic waveform database for these events from local and regional stations. The principal mines of interest are in northwest Russia (Khibiny Massif, Olenogorsk, Zapolyamy, and Kovdor groups) and Sweden (Malmberget, Kiruna). These mines form a natural laboratory for examining the variation of mining explosion observations with source type, since they include colocated surface and underground mines and mines conducting a variety of different shot types. In September 2002 we deployed two lines of temporary stations from the Khibiny Massif through and to the north of the ARCES station. This deployment is producing data that will allow researchers to examine the variation of discriminants caused by varying source-receiver distance and the diversity of explosion types. To date, we have collected ground-truth information on 1,118 explosions in the Kola Peninsula, and have assembled waveform data for approximately 700 of these. The database includes waveforms from instruments temporarily deployed in the Khibiny Massif mines, from the Apatity network just outside of the Massif, from LVZ, KEV and ARCES, and from the stations deployed along the two lines into northern Norway. In this paper we present representative waveforms for several types of shots recorded at various regional distances. We have conducted a preliminary study of the variation of phase ratios as a function of source type. This study shows significant differences in Pd/Sn and Pd/Lg ratios for two types of mining explosions: surface ripple-fired explosions and compact underground explosions. Compact explosions are, typically, underground explosions of a few tons with only one or two short delays, and are the closest approximation to single, well-tamped explosions available in the Khibiny mines. The surface shots typically are much larger (ranging up

  17. Chaotic Explosions

    CERN Document Server

    Altmann, Eduardo G; Tél, Tamás

    2015-01-01

    We investigate chaotic dynamical systems for which the intensity of trajectories might grow unlimited in time. We show that (i) the intensity grows exponentially in time and is distributed spatially according to a fractal measure with an information dimension smaller than that of the phase space,(ii) such exploding cases can be described by an operator formalism similar to the one applied to chaotic systems with absorption (decaying intensities), but (iii) the invariant quantities characterizing explosion and absorption are typically not directly related to each other, e.g., the decay rate and fractal dimensions of absorbing maps typically differ from the ones computed in the corresponding inverse (exploding) maps. We illustrate our general results through numerical simulation in the cardioid billiard mimicking a lasing optical cavity, and through analytical calculations in the baker map.

  18. Injury experience in coal mining, 1991

    Energy Technology Data Exchange (ETDEWEB)

    1991-12-31

    This Mine Safety and Health Administration (MSHA) informational report reviews in detail the occupational injury and illness experience of coal mining in the United States for 1991. Data reported by operators of mining establishments concerning work injuries are summarized by work location, accident classification, part of body injured, nature of injury, occupation, and anthracite or bituminous coal. Related information on employment, worktime, and operating activity also is presented. Data reported by independent contractors performing certain work at mining locations are depicted separately in this report. For ease of comparison between coal mining and the metal and nonmetal mineral mining industries, summary reference tabulations are included at the end of both the operator and the contractor sections of this report. Data used in compiling this report were reported by operators of coal mines and preparation plants on a mandatory basis as required under the Federal Mine Safety and Health Act of 1977, Public Law 91-173,as amended by Public Law 95-164. Since January 1, 1978, operators of mines or preparation plants or both which are subject to the Act have been required under 30 CFR, Part 50, to submit reports of injuries, occupational illnesses, and related data.

  19. ANALYSIS OF ABILITY FOR IGNITING METHANE OF WATER-CARRYING EXPLOSIVES

    Institute of Scientific and Technical Information of China (English)

    陆守香

    1997-01-01

    In this paper, the ability to ignite methane of water-carrying explosives is discussed in detail. The difference of the safety towards methane of water- carrying explosives and ammonite is analysed comparatively. It is shown that the process of detonation reaction, the duration of flame by combustible residues of detonation and the fineness of cooling salt in detonation products are important factors of the safety of explosive towards methane. Water-carrying explosives are safer than ammonite used in coal mines.

  20. Chemical profiling of explosives

    NARCIS (Netherlands)

    Brust, G.M.H.

    2014-01-01

    The primary goal of this thesis is to develop analytical methods for the chemical profiling of explosives. Current methodologies for the forensic analysis of explosives focus on identification of the explosive material. However, chemical profiling of explosives becomes increasingly important, as

  1. Basic problems and advances in the area of planning enterprises for working nonmetal mineral fields

    Energy Technology Data Exchange (ETDEWEB)

    Tudor, Gh.; Bucur, S.; Gavriliu, M.; Rusu, A.; Tamas, V.

    1980-01-01

    An examination is made of the problems and achievements in the area of planning enterprises for working fields of calcium, feldspar, kaolin, graphite, asbestos, rock salt, dolomite associated with the improvement in the economy of production, reduction in the consumption of energy and scarce materials. The developed program for improving the efficiency of production of nonmetal mineral stipulates an improvement in labor productivity, more efficient and more complete use of reserves, decrease in the volume of construction operations, improvement in the technology of extraction, increase in the degree of automation of processes, more skillful planning of the surface equipment for extraction and enrichment, reduction in the dimensions of designs of the units designed for enrichment and extraction, improvement in the efficient consumption of electricity with the help of a new system of power and distribution, reduction in consumption of fuel by the use of less expensive. A description is made of the different examples making it possible to achieve advances in these areas.

  2. Supernova explosions

    CERN Document Server

    Branch, David

    2017-01-01

    Targeting advanced students of astronomy and physics, as well as astronomers and physicists contemplating research on supernovae or related fields, David Branch and J. Craig Wheeler offer a modern account of the nature, causes and consequences of supernovae, as well as of issues that remain to be resolved. Owing especially to (1) the appearance of supernova 1987A in the nearby Large Magellanic Cloud, (2) the spectacularly successful use of supernovae as distance indicators for cosmology, (3) the association of some supernovae with the enigmatic cosmic gamma-ray bursts, and (4) the discovery of a class of superluminous supernovae, the pace of supernova research has been increasing sharply. This monograph serves as a broad survey of modern supernova research and a guide to the current literature. The book’s emphasis is on the explosive phases of supernovae. Part 1 is devoted to a survey of the kinds of observations that inform us about supernovae, some basic interpreta tions of such data, and an overview of t...

  3. An Emulsion Explosive Containing Gunpowder Applied in Large-diameter Blasting of Surface Mine%一种用于露天大孔径爆破的含火药乳化炸药

    Institute of Scientific and Technical Information of China (English)

    谢永祥; 杨民刚; 王敏祥

    2012-01-01

    含火药乳化炸药是利用超期退役的废弃发射药与乳化炸药相混后制成。文中分析总结了该炸药的爆炸性能、安全使用要求和实际应用效果。%Emulsion explosive containing powder is prepared by mixing overdue retJred waste gun propellant and emulsion explosive. Its explosive performance, safety requirements for the use and practical application effect are analyzed and summarized in this paper.

  4. Mine Safety Detection System (MSDS)

    Science.gov (United States)

    2012-09-01

    BLANK xiii LIST OF ACRONYMS AND ABBREVIATIONS Acronym Term ALMDS Airborne Laser -Mine Detection System AMCM Airborne Mine Countermeasure AoA...Streak Tube Imaging Laser ULCC Ultra Large Crude Carrier USN United States Navy UWIED Under Water Improvised Explosive Devices VLCC Very Large Crude...active sonar, passive sonar, infra-red (IR) thermal imaging, LIDAR (Light Detection and Ranging), and the use of marine mammals ( dolphins and porpoises

  5. Lipophilic super-absorbent polymer gels as surface cleaners for oil and grease from metal and non-metal surfaces

    Science.gov (United States)

    The objective of this research is to develop a new cleaning technology based on lipophilic super-absorbent swelling gels for the removal of oil, grease and particulate matters from metal and non-metal surfaces. It is desired that the cleaner is in solid form and is VOC-exempt, HAP-free, non-toxic, n...

  6. Super-Absorbent polymer gels for oil and grease removal from metal and non-metal surfaces

    Science.gov (United States)

    The objective of this research is to develop a new surface cleaning technology for removal of oil, grease and particulate matters from metal and non-metal surfaces. It is desired that the cleaner is in solid form and is VOC-exempt, HAP-free, non-toxic, non-corrosive, non-ozone depleting, recyclable...

  7. Understanding vented gas explosions

    Energy Technology Data Exchange (ETDEWEB)

    Lautkaski, R. [VTT Energy, Espoo (Finland). Energy Systems

    1997-12-31

    The report is an introduction to vented gas explosions for nonspecialists, particularly designers of plants for flammable gases and liquids. The phenomena leading to pressure generation in vented gas explosions in empty and congested rooms are reviewed. The four peak model of vented gas explosions is presented with simple methods to predict the values of the individual peaks. Experimental data on the external explosion of dust and gas explosions is discussed. The empirical equation relating the internal and external peak pressures in vented dust explosions is shown to be valid for gas explosion tests in 30 m{sup 3} and 550 m{sup 3} chambers. However, the difficulty of predicting the internal peak pressure in large chambers remains. Methods of explosion relief panel design and principles of vent and equipment layout to reduce explosion overpressures are reviewed. (orig.) 65 refs.

  8. Proceedings of the 7th international mine ventilation congress

    Energy Technology Data Exchange (ETDEWEB)

    Wasilewski, S. (ed.)

    2001-07-01

    The proceedings contains 139 papers covering the topics: ventilation analysis; heat assessment; methane emission and drainage; human factors; health and contaminations; fans and systems; dust generation and control; ventilation network and simulation systems and virtual reality; mine explosions; ventilation studies; mine fire determination planning; mine fires prevention studies; diesels; and case studies. Selected papers have been abstracted for IEA Coal Research coal abstract database.

  9. 空气及非金属材料脱气中苯的GC/MS-SIM分析方法%GC/MS- SIM Analysis Method for Benzene in Ambient Air and Offgas of Nonmetal Material

    Institute of Scientific and Technical Information of China (English)

    于芳; 何正杰; 姜洁; 何新

    2001-01-01

    We have built GC/MS - SIM analysis method for benzene in ambient air and offgas of nonmetal material and determined the concentration of benzene in the offgas of a kind of nonmetal material with external standard quantity method.

  10. 78 FR 64246 - Commerce in Explosives; List of Explosives Materials

    Science.gov (United States)

    2013-10-28

    ... From the Federal Register Online via the Government Publishing Office ] DEPARTMENT OF JUSTICE Bureau of Alcohol, Tobacco, Firearms, and Explosives Commerce in Explosives; List of Explosives Materials AGENCY: Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF); Department of Justice. ACTION:...

  11. Explosive vapor detection payload for small robots

    Science.gov (United States)

    Stimac, Phil J.; Pettit, Michael; Wetzel, John P.; Haas, John W.

    2013-05-01

    Detection of explosive hazards is a critical component of enabling and improving operational mobility and protection of US Forces. The Autonomous Mine Detection System (AMDS) developed by the US Army RDECOM CERDEC Night Vision and Electronic Sensors Directorate (NVESD) is addressing this challenge for dismounted soldiers. Under the AMDS program, ARA has developed a vapor sampling system that enhances the detection of explosive residues using commercial-off-the-shelf (COTS) sensors. The Explosives Hazard Trace Detection (EHTD) payload is designed for plug-and-play installation and operation on small robotic platforms, addressing critical Army needs for more safely detecting concealed or exposed explosives in areas such as culverts, walls and vehicles. In this paper, we describe the development, robotic integration and performance of the explosive vapor sampling system, which consists of a sampling "head," a vapor transport tube and an extendable "boom." The sampling head and transport tube are integrated with the boom, allowing samples to be collected from targeted surfaces up to 7-ft away from the robotic platform. During sample collection, an IR lamp in the sampling head is used to heat a suspected object/surface and the vapors are drawn through the heated vapor transport tube to an ion mobility spectrometer (IMS) for detection. The EHTD payload is capable of quickly (less than 30 seconds) detecting explosives such as TNT, PETN, and RDX at nanogram levels on common surfaces (brick, concrete, wood, glass, etc.).

  12. Risk Assessment Study for Storage Explosive

    Directory of Open Access Journals (Sweden)

    S. S. Azhar

    2006-01-01

    Full Text Available In Malaysia, there has been rapidly increasing usage in amount of explosives due to widely expansion in quarrying and mining industries. The explosives are usually stored in the storage where the safety precaution had given high attention. As the storage of large quantity of explosive can be hazardous to workers and nearby residents in the events of accidental denotation of explosives, a risk assessment study for storage explosive (magazine had been carried out. Risk assessment study had been conducted in Kimanis Quarry Sdn. Bhd, located in Sabah. Risk assessment study had been carried out with the identification of hazards and failure scenarios and estimation of the failure frequency of occurrence. Analysis of possible consequences of failure and the effects of blast waves due to the explosion was evaluated. The risk had been estimated in term of fatalities and eardrum rupture to the workers and public. The average individual voluntary risk for fatality to the workers at the quarry is calculated to be 5.75 x 10-6 per person per year, which is much lower than the acceptable level. Eardrum rupture risk calculated to be 3.15 x 10-6 per person per year for voluntary risk. There is no involuntary risk found for fatality but for eardrum rupture it was calculated to be 6.98 x 10-8 per person per year, as given by Asian Development Bank.

  13. Internet multimedia and search mining

    CERN Document Server

    Hua, Xian-Sheng

    2013-01-01

    With the explosion of video and image data available on the Internet, desktops and mobile devices, multimedia search has gained immense importance. This is the first reference book on the subject of internet multimedia search and mining and it will be extremely useful for graduates, researchers and working professionals in the field of information technology and multimedia content analysis.

  14. Totally confined explosive welding

    Science.gov (United States)

    Bement, L. J. (Inventor)

    1978-01-01

    The undesirable by-products of explosive welding are confined and the association noise is reduced by the use of a simple enclosure into which the explosive is placed and in which the explosion occurs. An infrangible enclosure is removably attached to one of the members to be bonded at the point directly opposite the bond area. An explosive is completely confined within the enclosure at a point in close proximity to the member to be bonded and a detonating means is attached to the explosive. The balance of the enclosure, not occupied by explosive, is filled with a shaped material which directs the explosive pressure toward the bond area. A detonator adaptor controls the expansion of the enclosure by the explosive force so that the enclosure at no point experiences a discontinuity in expansion which causes rupture. The use of the technique is practical in the restricted area of a space station.

  15. Cell phone explosion.

    Science.gov (United States)

    Atreya, Alok; Kanchan, Tanuj; Nepal, Samata; Pandey, Bhuwan Raj

    2016-03-01

    Cell phone explosions and resultant burn injuries are rarely reported in the scientific literature. We report a case of cell phone explosion that occurred when a young male was listening to music while the mobile was plugged in for charging.

  16. NEW EXPLOSIVE WELDING TECHNIQUES

    OpenAIRE

    Lotous, V.; Dragobetskii, V.

    2015-01-01

    Purpose - analysis of the variety of factors of the physical phenomena accompanying the process of the power explosive effect for development of new processes of metal treatment: explosive film coating of hardening and updating of a superficial layer of an item. Industrial approbation of cladding techniques by explosion of item surfaces of complex configuration and determination of parameters of the process of the explosive welding of high-strength pig-iron (graphite of the spherical form) wi...

  17. Photoacoustic Sensing of Explosives

    Science.gov (United States)

    2013-11-01

    NOV 2013 2. REPORT TYPE 3. DATES COVERED 00-00-2013 to 00-00-2013 4. TITLE AND SUBTITLE Photoacoustic Sensing of Explosives 5a. CONTRACT NUMBER...2013www.ll.mit.edu Photoacoustic Sensing of Explosives (PHASE) is a promising new technology that detects trace explosive residues from significant... photoacoustic phenomena resulting from ultraviolet laser excitation. Exposed explosives are excited up to 100 meters away by using PHASE’s

  18. Inspection tester for explosives

    Science.gov (United States)

    Haas, Jeffrey S.; Simpson, Randall L.; Satcher, Joe H.

    2007-11-13

    An inspection tester that can be used anywhere as a primary screening tool by non-technical personnel to determine whether a surface contains explosives. It includes a body with a sample pad. First and second explosives detecting reagent holders and dispensers are operatively connected to the body and the sample pad. The first and second explosives detecting reagent holders and dispensers are positioned to deliver the explosives detecting reagents to the sample pad. A is heater operatively connected to the sample pad.

  19. Explosive Line Wave Generators

    Science.gov (United States)

    2013-12-01

    curvature produced by each line wave generator. Piezoelectric pins were used for an additional assessment of the explosive lens design...to a visual assessment of the wave curvature from the high speed camera images, the explosive lens design was also evaluated using piezoelectric pins...High Explosive Firing Complex (HEFC). The various explosive line wave generators were taped vertically on a supporting board and the detonation wave

  20. Metals, non-metals and PCB in electrical and electronic waste--actual levels in Switzerland.

    Science.gov (United States)

    Morf, Leo S; Tremp, Josef; Gloor, Rolf; Schuppisser, Felix; Stengele, Markus; Taverna, Ruedi

    2007-01-01

    The chemical composition of waste of small electrical and electronic equipment (s-WEEE), a rapidly growing waste stream, was determined for selected metals (Cu, Sb, Hg etc.) and non-metals (Cl, Br, P) and PCBs. During a 3-day experiment, all output products and the s-WEEE input mass flows in a WEEE recycling plant were measured. Only output products were sampled and analyzed. Material balances were established, applying substance flow analysis (SFA). Transfer coefficients for the selected substances were also determined. The results demonstrate the capability of SFA to determine the composition of the highly heterogeneous WEEE for most substances with rather low uncertainty (2 sigma +/- 30%). The results confirm the growing importance of s-WEEE regarding secondary resource metals and potential toxic substances. Nowadays, the thirty times smaller s-WEEE turns over larger flows for many substances, compared to municipal solid waste. Transfer coefficient results serve to evaluate the separation efficiency of the recycling process and confirm--with the exception of PCB and Hg--the limitation of hand-sorting and mechanical processing to separate pollutants (Cd, Pb, etc.) out of reusable fractions. Regularly applied SFA would serve to assess the efficacy of legislative, organizational and technical measures on the WEEE.

  1. Tunable redox potential of nonmetal doped monolayer MoS2: First principle calculations

    Science.gov (United States)

    Lu, S.; Li, C.; Zhao, Y. F.; Gong, Y. Y.; Niu, L. Y.; Liu, X. J.

    2016-10-01

    Doping is an effective method to alter the electronic behavior of materials by forming new chemical bonds and bringing bond relaxation. With this aid of first principle calculations, the crystal configuration and electronic properties of monolayer MoS2 have been modulated by the nonmetal (NM) dopants (H, B, C, N, O, F, Si, P, Cl, As, Se, Br, Te and I), and the thermodynamic stability depending on the preparation conditions (Mo-rich and S-rich conditions) were discussed. Results shown that, the NM dopants substituted preferentially for S under Mo-rich condition, the electronic distribution around the dopants and the nearby Mo atoms are changed by the new formed Mo-NM bonds and bands relaxation. Compared to pristine monolayer MoS2, the NM ions with odd chemical valences enhance the oxidation potential and reduce the reduction potential of specimens, but the NM ions with even chemical valences have the opposite effects on the redox potentials. Compared to the NM ions with even chemical valences, the lone pair electrons in NM ions with odd chemical valences can extra interact with the Mo ions and reduces the ECBM and EVBM values of specimens. It offers a simple way to design various monolayer MoS2 based catalysts in order to catalyze different materials by chose the reasonable dopants for stronger oxidation or reduction potential.

  2. Identification of Mine-Shaped Objects based on an Efficient Phase Stepped-Frequency Radar Approach

    DEFF Research Database (Denmark)

    Sørensen, Helge Bjarup Dissing; Jakobsen, Kaj Bjarne; Nymann, Ole

    1997-01-01

    A computational efficient approach to identify very small mine-shaped plastic objects, e.g. M56 Anti-Personnel (AP) mines buried in the ground, is presented. The size of the objects equals the smallest AP-mines in use today, i.e., the most difficult mines to detect with respect to humanitarian mine...... a radar probe is moved automatically to measure in each grid point a set of reflection coefficients from which phase and amplitude information are extracted. Based on a simple processing of the phase information, quarternary image and template cross-correlation a successful detection of metal- and non......-metal mine-shaped objects is possible. Measurements have been performed on loamy soil containing different mine-shaped objects...

  3. 30 CFR 57.6501 - Nonelectric initiation systems.

    Science.gov (United States)

    2010-07-01

    ... NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Explosives Nonelectric Blasting-Surface and Underground § 57.6501 Nonelectric initiation systems. (a) When the... blasts, the trunkline layout shall be designed so that the detonation can reach each blasthole from...

  4. 30 CFR 57.6605 - Isolation of blasting circuits.

    Science.gov (United States)

    2010-07-01

    ... NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Explosives Extraneous Electricity-Surface and Underground § 57.6605 Isolation of blasting circuits. Lead wires and blasting lines shall be isolated and insulated from power conductors, pipelines, and railroad tracks, and...

  5. Chemical industrial production and applied chemistry of metals and nonmetals in educational program of chemistry in elementary school

    OpenAIRE

    Cvjetićanin Stanko M.; Segedinac Mirjana; Letić Ljubinka B.

    2009-01-01

    In this paper a part of the model of the curriculum, which should improve chemical education in primary schools is presented. The implemented module refers to metals and non-metals in the fields of applied chemistry and chemical industry. Contents of the curriculum from 1974 to 2004 are considered. The quantity and quality of the pupils' knowledge are analyzed. The research showed that the pupils' knowledge is low. The module is implemented for the sake of overcoming the observed drawbacks in...

  6. Cleavage of hydrogen by activation at a single non-metal centre - towards new hydrogen storage materials.

    Science.gov (United States)

    Grabowski, Sławomir J

    2015-05-28

    Molecular surfaces of non-metal species are often characterized by both positive and negative regions of electrostatic potential (EP) at a non-metal centre. This centre may activate molecular hydrogen which further leads to the addition reaction. The positive EP regions at the non-metal centres correspond to σ-holes; the latter sites are enhanced by electronegative substituents. This is why the following simple moieties; PFH2, SFH, AsFH2, SeFH, BrF3, PF(CH3)2 and AsF(CH3)2, were chosen here to analyze the H2 activation and its subsequent splitting at the P, As, S, Se and Br centres. Also the reverse H-H bond reforming process is analyzed. MP2/aug-cc-pVTZ calculations were performed for systems corresponding to different stages of these processes. The sulphur centre in the SFH moiety is analyzed in detail since the potential barrier height for the addition reaction for this species is the lowest of the moieties analyzed here. The results of calculations show that the SFH + H2 → SFH3 reaction in the gas phase is endothermic but it is exothermic in polar solvents.

  7. Landmine Detection Technologies to TraceExplosive Vapour Detection Techniques

    Directory of Open Access Journals (Sweden)

    J. C. Kapoor

    2007-11-01

    Full Text Available Large quantity of explosive is manufactured worldwide for use in various types of ammunition,arms, and mines, and used in armed conflicts. During manufacturing and usage of the explosiveequipment, some of the explosive residues are released into the environment in the form ofcontaminated effluents, unburnt explosives fumes and vapours. Limited but uncontrolledcontinuous release of trace vapours also takes place when explosive-laden landmines are deployedin the field. One of the major technological challenges in post-war scenario worldwide is thedetection of landmines using these trace vapour signatures and neutralising them safely.  Differenttypes of explosives are utilised as the main charge in antipersonnel and antitank landmines. Inthis paper, an effort has been made to review the techniques so far available based on explosivevapour detection especially to detect the landmines. A comprehensive compilation of relevantinformation on the techniques is presented, and their maturity levels, shortcomings, and difficultiesfaced are highlighted.

  8. Acoustic resonance for nonmetallic mine detection

    Energy Technology Data Exchange (ETDEWEB)

    Kercel, S.W.

    1998-04-01

    The feasibility of acoustic resonance for detection of plastic mines was investigated by researchers at the Oak Ridge National Laboratory`s Instrumentation and Controls Division under an internally funded program. The data reported in this paper suggest that acoustic resonance is not a practical method for mine detection. Representative small plastic anti-personnel mines were tested, and were found to not exhibit detectable acoustic resonances. Also, non-metal objects known to have strong acoustic resonances were tested with a variety of excitation techniques, and no practical non-contact method of exciting a consistently detectable resonance in a buried object was discovered. Some of the experimental data developed in this work may be useful to other researchers seeking a method to detect buried plastic mines. A number of excitation methods and their pitfalls are discussed. Excitation methods that were investigated include swept acoustic, chopped acoustic, wavelet acoustic, and mechanical shaking. Under very contrived conditions, a weak response that could be attributed to acoustic resonance was observed, but it does not appear to be practical as a mine detection feature. Transfer properties of soil were investigated. Impulse responses of several representative plastic mines were investigated. Acoustic leakage coupling, and its implications as a disruptive mechanism were investigated.

  9. SANFO: The missing link in explosives technology

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, R.J. [Johnson Hi-Tech Australia Pty Ltd, Queensland (Australia)

    1996-12-01

    The development of SANFO has provided the mining industry with a low cost high gas volume, variable density, blasting agent which can be blended on site in a simple agitator mixing and charging system by mine site employees. During the last decade most major explosives manufacturers have been promoting high density, high shock energy blasting agents. To offset the cost of these products they have relied on expanded borehole patterns. It has since been discovered that lower VOD products are more effective in most overburden geologies due to the longer explosion pressure period and lower shock energy. These characteristics also reduce energy loss consumed in pulverization around the perimeter of borehole. The major advantages of SANFO compared with normal ANFO or heavy ANFO are as listed. Due to problems associated with bulling when blasting soft geologies at BHP`s Riverside Mine in Central Queensland, Australia, the company was invited to develop a low density blasting agent which could be blended as required on the mine site. This paper describes the problems associated with blasting softer geologies and the use of sawdust as a cost-effective bulking agent.

  10. Real time explosive hazard information sensing, processing, and communication for autonomous operation

    Energy Technology Data Exchange (ETDEWEB)

    Versteeg, Roelof J; Few, Douglas A; Kinoshita, Robert A; Johnson, Doug; Linda, Ondrej

    2015-02-24

    Methods, computer readable media, and apparatuses provide robotic explosive hazard detection. A robot intelligence kernel (RIK) includes a dynamic autonomy structure with two or more autonomy levels between operator intervention and robot initiative A mine sensor and processing module (ESPM) operating separately from the RIK perceives environmental variables indicative of a mine using subsurface perceptors. The ESPM processes mine information to determine a likelihood of a presence of a mine. A robot can autonomously modify behavior responsive to an indication of a detected mine. The behavior is modified between detection of mines, detailed scanning and characterization of the mine, developing mine indication parameters, and resuming detection. Real time messages are passed between the RIK and the ESPM. A combination of ESPM bound messages and RIK bound messages cause the robot platform to switch between modes including a calibration mode, the mine detection mode, and the mine characterization mode.

  11. Real time explosive hazard information sensing, processing, and communication for autonomous operation

    Energy Technology Data Exchange (ETDEWEB)

    Versteeg, Roelof J.; Few, Douglas A.; Kinoshita, Robert A.; Johnson, Douglas; Linda, Ondrej

    2015-12-15

    Methods, computer readable media, and apparatuses provide robotic explosive hazard detection. A robot intelligence kernel (RIK) includes a dynamic autonomy structure with two or more autonomy levels between operator intervention and robot initiative A mine sensor and processing module (ESPM) operating separately from the RIK perceives environmental variables indicative of a mine using subsurface perceptors. The ESPM processes mine information to determine a likelihood of a presence of a mine. A robot can autonomously modify behavior responsive to an indication of a detected mine. The behavior is modified between detection of mines, detailed scanning and characterization of the mine, developing mine indication parameters, and resuming detection. Real time messages are passed between the RIK and the ESPM. A combination of ESPM bound messages and RIK bound messages cause the robot platform to switch between modes including a calibration mode, the mine detection mode, and the mine characterization mode.

  12. Combining metal and nonmetal isotopic measurements in barite to identify mode of formation

    Science.gov (United States)

    Griffith, E. M.; Paytan, A.; Eisenhauer, A.; Scher, H. D.; Wortmann, U.

    2014-12-01

    Barite (BaSO4) is a highly stable and widely-distributed mineral found in magmatic, metamorphic, and sedimentary rocks (of all ages), as well as in soils, aerosol dust, and extraterrestrial material. Today, barite can form in a variety of settings in the oceans (hydrothermal, cold seeps, water column, sediments) and on the continents - where supersaturation and precipitation of barite typically occurs from the mixing of fluids - one containing Ba and another containing sulfate. Sulfur (δ34S) and oxygen (δ18O) isotopes together with 87Sr/86Sr and stable Sr-isotopic signatures (δ88/86Sr) of modern authigenic continental barite are compared to modern pelagic marine barite and marine hydrothermal and cold seep barite to investigate the potential for their combined use to indicate mode of barite formation. The 87Sr/86Sr in barite cleary identifies the source of fluid for any particular type of barite (as previously noted, see Paytan et al., 2002). The highest (most radiogenic) 87Sr/86Sr values are measured in continental barite samples. There is no unique δ88/86Sr signature for any particular type of barite, but coretop marine (pelagic) barite has a consistent value measured from samples collected in different ocean basins. The highest and lowest δ88/86Sr values were measured in continental barite samples. The combination of isotopic systems result in unique δ88/86Sr and δ18O relationships and distinct δ88/86Sr and δ34S relationships for different types of barites investigated. Data suggest that the combined use of these metal and nonmetal isotopic measurements in barite could be useful as a new geochemical proxy to identify mode of barite mineralization for use in earth science applications including understanding ancient barite deposits.

  13. New Mix Explosives for Explosive Welding

    Science.gov (United States)

    Andreevskikh, Leonid

    2011-06-01

    Suggested and tested were some mix explosives--powder mixtures of a brisant high explosive (HE = RDX, PETN) and an inert diluent (baking soda)--for use in explosive welding. RDX and PETN were selected in view of their high throwing ability and low critical diameter. Since the decomposition of baking soda yields a huge amount of gaseous products, its presence ensures (even at a low HE percentage) a throwing speed that is sufficient for realization of explosive welding, at a reduced brisant action of charge. Mix chargers containing 30-70 wt % HE (the rest baking soda) have been tested experimentally and optimized. For study of possibility to reduce critical diameter of HE mixture, the mixture was prepared where HE crystal sizes did not exceed 10 μm. The tests, which were performed with this HE, revealed that the mixture detonated stably with the velocity D ~ 2 km/s, if the layer thickness was d = 2 mm. The above explosives afford to markedly diminish deformations within the oblique impact zone and thus to carry out explosive welding of hollow items and thin metallic foils.

  14. Use of wavelets techniques to discriminate between explosions and natural earthquakes

    Science.gov (United States)

    Beccar-Varela, Maria P.; Gonzalez-Huizar, Hector; Mariani, Maria C.; Tweneboah, Osei K.

    2016-09-01

    Wavelets analysis is used to discriminate between explosions and natural earthquakes. We applied wavelets techniques to analyze the seismograms of a set of mining explosions, reported in catalogs as earthquakes, and compared them with natural earthquakes that occurred in the same region (within a radius of 10 km).

  15. 30 CFR 817.66 - Use of explosives: Blasting signs, warnings, and access control.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Use of explosives: Blasting signs, warnings... STANDARDS-UNDERGROUND MINING ACTIVITIES § 817.66 Use of explosives: Blasting signs, warnings, and access control. (a) Blasting signs. Blasting signs shall meet the specifications of § 817.11. The operator...

  16. 30 CFR 816.68 - Use of explosives: Records of blasting operations.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Use of explosives: Records of blasting...-SURFACE MINING ACTIVITIES § 816.68 Use of explosives: Records of blasting operations. The operator shall... § 816.67(e). (e) Weather conditions, including those which may cause possible adverse blasting...

  17. 30 CFR 817.68 - Use of explosives: Records of blasting operations.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Use of explosives: Records of blasting...-UNDERGROUND MINING ACTIVITIES § 817.68 Use of explosives: Records of blasting operations. The operator shall... § 817.67 (e). (e) Weather conditions, including those which may cause possible adverse blasting...

  18. 30 CFR 816.66 - Use of explosives: Blasting signs, warnings, and access control.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Use of explosives: Blasting signs, warnings... STANDARDS-SURFACE MINING ACTIVITIES § 816.66 Use of explosives: Blasting signs, warnings, and access control. (a) Blasting signs. Blasting signs shall meet the specifications of § 816.11. The operator shall—...

  19. Applications of Radio Frequency Identification (RFID) in Mining Industries

    Science.gov (United States)

    Khairul Nizam Mahmad, Mohd; Z, Mohd Remy Rozainy M. A.; Baharun, Norlia

    2016-06-01

    RFID technology has recently become a dream of many companies or organizations because of its strategic potential in transforming mining operations. Now is the perfect time, for RFID technology arise as the next revolution in mining industries. This paper will review regarding the application of RFID in mining industries and access knowledge regarding RFID technology and overseen the opportunity of this technology to become an importance element in mining industries. The application of Radio-Frequency Identification (RFID) in mining industries includes to control of Personal Protective Equipment (PPE), control of personnel to access mining sites and RFID solutions for tracking explosives.

  20. Mining Frequent Itemsets from Online Data Streams: Comparative Study

    Directory of Open Access Journals (Sweden)

    HebaTallah Mohamed Nabil

    2013-08-01

    Full Text Available Online mining of data streams poses many new challenges more than mining static databases. In addition to the one-scan nature, the unbounded memory requirement, the high data arrival rate of data streams and the combinatorial explosion of itemsets exacerbate the mining task. The high complexity of the frequent itemsets mining problem hinders the application of the stream mining techniques. In this review, we present a comparative study among almost all, as we are acquainted, the algorithms for mining frequent itemsets from online data streams. All those techniques immolate with the accuracy of the results due to the relatively limited storage, leading, at all times, to approximated results.

  1. Explosives tester with heater

    Science.gov (United States)

    Del Eckels, Joel [Livermore, CA; Nunes, Peter J [Danville, CA; Simpson, Randall L [Livermore, CA; Whipple, Richard E [Livermore, CA; Carter, J Chance [Livermore, CA; Reynolds, John G [San Ramon, CA

    2010-08-10

    An inspection tester system for testing for explosives. The tester includes a body and a swab unit adapted to be removeably connected to the body. At least one reagent holder and dispenser is operatively connected to the body. The reagent holder and dispenser contains an explosives detecting reagent and is positioned to deliver the explosives detecting reagent to the swab unit. A heater is operatively connected to the body and the swab unit is adapted to be operatively connected to the heater.

  2. Explosive Technology Group

    Data.gov (United States)

    Federal Laboratory Consortium — The Explosive Technology Group (ETG) provides diverse technical expertise and an agile, integrated approach to solve complex challenges for all classes of energetic...

  3. Longwall mining

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-14

    As part of EIA`s program to provide information on coal, this report, Longwall-Mining, describes longwall mining and compares it with other underground mining methods. Using data from EIA and private sector surveys, the report describes major changes in the geologic, technological, and operating characteristics of longwall mining over the past decade. Most important, the report shows how these changes led to dramatic improvements in longwall mining productivity. For readers interested in the history of longwall mining and greater detail on recent developments affecting longwall mining, the report includes a bibliography.

  4. Expert system for assessing risk and prevention of methane explosions in coal mines. Sistema experto para evaluacion del riesgo y la prevencion de explosiones de grisu en minas de carbon

    Energy Technology Data Exchange (ETDEWEB)

    1991-05-01

    The expert system described here was developed by members of AITEMIN as part of a project financed by Ocicarbon, the General Directorate of Mines and MINER Construction. The article begins by asking the question, 'What is an expert system '. 1 tab.

  5. Imaging Detonations of Explosives

    Science.gov (United States)

    2016-04-01

    14. ABSTRACT The techniques and instrumentation presented in this report allow for mapping of temperature, pressure , chemical species, and...measurement in the explosive near- to far-field (0–500 charge diameters) of surface temperatures, peak air-shock pressures , some chemical species...15. SUBJECT TERMS imaging, explosions, temperature, pressure , chemical species 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU

  6. Explosions and static electricity

    DEFF Research Database (Denmark)

    Jonassen, Niels M

    1995-01-01

    The paper deals with the problem of electrostatic discharges as causes of ignition of vapor/gas and dust/gas mixtures. A series of examples of static-caused explosions will be discussed. The concepts of explosion limits, the incendiveness of various discharge types and safe voltages are explained...

  7. Melt Cast High Explosives

    Directory of Open Access Journals (Sweden)

    Stanisław Cudziło

    2014-12-01

    Full Text Available [b]Abstract[/b]. This paper reviews the current state and future developments of melt-cast high explosives. First the compositions, properties and methods of preparation of trinitrotoluene based (TNT conventional mixtures with aluminum, hexogen (RDX or octogen (HMX are described. In the newer, less sensitive explosive formulations, TNT is replaced with dinitroanisole (DNANDNANDNAN and nitrotriazolone (NTONTONTO, nitroguanidine (NG or ammonium perchlorate (AP are the replacement for RDRDX and HMX. Plasticized wax or polymer-based binder systems for melt castable explosives are also included. Hydroxyl terminated polybutadiene (HPTB is the binder of choice, but polyethylene glycol, and polycaprolactone with energetic plasticizers are also used. The most advanced melt-cast explosives are compositions containing energetic thermoplastic elastomers and novel highly energetic compounds (including nitrogen rich molecules in whose particles are nanosized and practically defect-less.[b]Keywords[/b]: melt-cast explosives, detonation parameters

  8. Data mining methods and applications

    CERN Document Server

    Lawrence, Kenneth D; Klimberg, Ronald K

    2007-01-01

    With today's information explosion, many organizations are now able to access a wealth of valuable data. Unfortunately, most of these organizations find they are ill-equipped to organize this information, let alone put it to work for them. Gain a Competitive Advantage Employ data mining in research and forecasting Build models with data management tools and methodology optimization Gain sophisticated breakdowns and complex analysis through multivariate, evolutionary, and neural net methodsLearn how to classify data and maintain qualityTransform Data into Business Acumen Data Mining Methods and

  9. Ignitability and explosibility of gases and vapors

    CERN Document Server

    Ma, Tingguang

    2015-01-01

    The book provides a systematic view on flammability and a collection of solved engineering problems in the fields of dilution and purge, mine gas safety, clean burning safety and gas suppression modeling. For the first time, fundamental principles of energy conservation are used to develop theoretical flammability diagrams and are then explored to understand various safety-related mixing problems. This provides the basis for a fully-analytical solution to any flammability problem. Instead of the traditional view that flammability is a fundamental material property, here flammability is discovered to be a result of the explosibility of air and the ignitability of fuel, or a process property. By exploring the more fundamental concepts of explosibility and ignitability, the safety targets of dilution and purge can be better defined and utilized for guiding safe operations in process safety. This book provides various engineering approaches to mixture flammability, benefiting not only the safety students, but al...

  10. Detecting underwater improvised explosive threats (DUIET)

    Science.gov (United States)

    Feeley, Terry

    2010-04-01

    Improvised Explosive Devices (IEDs) have presented a major threat in the wars in Afghanistan and Iraq. These devices are powerful homemade land mines that can be small and easily hidden near roadsides. They are then remotely detonated when Coalition Forces pass by either singly or in convoys. Their rapid detection, classification and destruction is key to the safety of troops in the area. These land based bombs will have an analogue in the underwater theater especially in ports, lakes, rivers and streams. These devices may be used against Americans on American soil as an element of the global war on terrorism (GWOT) Rapid detection and classification of underwater improvised explosive devices (UIED) is critical to protecting innocent lives and maintaining the day to day flow of commerce. This paper will discuss a strategy and tool set to deal with this potential threat.

  11. Death and injury caused by land mines in Burma

    DEFF Research Database (Denmark)

    Hougen, H P; Petersen, H D; Lykke, J

    2000-01-01

    One hundred and eighty-eight Burmese refugees in Thailand were interviewed. One hundred and five of those interviewed had knowledge of a total of 313 persons who had been exposed to land mine explosions. Twenty-three of the interviewed were land mine survivors. They were all male, aged between...

  12. Co-recycling of acrylonitrile-butadiene-styrene waste plastic and nonmetal particles from waste printed circuit boards to manufacture reproduction composites.

    Science.gov (United States)

    Sun, Zhixing; Shen, Zhigang; Zhang, Xiaojing; Ma, Shulin

    2015-01-01

    This study investigated the feasibility of using acrylonitrile-butadiene-styrene (ABS) waste plastic and nonmetal particles from waste printed circuit boards (WPCB) to manufacture reproduction composites (RC), with the aim of co-recycling these two waste resources. The composites were prepared in a twin-crew extruder and investigated by means of mechanical testing, in situ flexural observation, thermogravimatric analysis, and dimensional stability evaluation. The results showed that the presence of nonmetal particles significantly improved the mechanical properties and the physical performance of the RC. A loading of 30 wt% nonmetal particles could achieve a flexural strength of 72.6 MPa, a flexural modulus of 3.57 GPa, and an impact strength of 15.5 kJ/m2. Moreover, it was found that the application of maleic anhydride-grafted ABS as compatilizer could effectively promote the interfacial adhesion between the ABS plastic and the nonmetal particles. This research provides a novel method to reuse waste ABS and WPCB nonmetals for manufacturing high value-added product, which represents a promising way for waste recycling and resolving the environmental problem.

  13. The Hillcrest mine disaster: Canada's deadliest mining accident

    Energy Technology Data Exchange (ETDEWEB)

    Baldwin, Corey

    2011-02-15

    On June 19, 1914, the worst mining incident in Canadian history occurred at the Hillcrest coal mine in the Crowsnest Pass, in the southern Alberta-BC border. An overproduction occurred a few days before the disaster and the mine was then shut down during the two previous days to check for methane gas pockets. As the union committee did not find any, work resumed on June 19 and 234 men entered the mine. At 9:30 a.m. a massive explosion took place followed by one or two other explosions. The entrance to the mine was obstructed trapping the survivors in the mine with a lack of oxygen and rise of CO2 levels up to 50%. Rescue teams entered the mine facing the risk of further explosions and 46 men were saved by the end of the day. To commemorate this accident a monument was built at the entrance to the Hillcrest cemetery in honor of all miners killed on the job in Canada.

  14. Some features of the detonation of plane charges of Uglenit E-6 with applications to explosive welding

    Energy Technology Data Exchange (ETDEWEB)

    Ogolikhin, V.M.

    1983-09-01

    This article investigates the possibility of using Uglenit E-6 GOST, a permissible explosive employed in mines, etc., with gas or dust risks, for explosive welding purposes. The detonation velocity of Uglenit E-6 was measured using contact wires. For explosive welding it is desirable that the detonation velocity be less than the speed of sound in the materials being welded. It is determined that the constancy of the detonation velocity with increase in charge thickness above 30 mm is a great advantage of Uglenit E-6 as compared with loose-packed AN explosives. The results indicate that Uglenit E-6 can be used for explosive welding.

  15. Text Mining.

    Science.gov (United States)

    Trybula, Walter J.

    1999-01-01

    Reviews the state of research in text mining, focusing on newer developments. The intent is to describe the disparate investigations currently included under the term text mining and provide a cohesive structure for these efforts. A summary of research identifies key organizations responsible for pushing the development of text mining. A section…

  16. Text Mining.

    Science.gov (United States)

    Trybula, Walter J.

    1999-01-01

    Reviews the state of research in text mining, focusing on newer developments. The intent is to describe the disparate investigations currently included under the term text mining and provide a cohesive structure for these efforts. A summary of research identifies key organizations responsible for pushing the development of text mining. A section…

  17. Study of blasting vibrations in Sarcheshmeh copper mine

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Ground vibration is one of the side effects of blasting, in which way considerable amount of explosive energy is exhausted, and causes decrease in production and even decline in mine development workings. In this study, 57 recorded 3-C seismograms from 11 blasts in Sarcheshmeh copper mine, Kerman, Iran, are processed and analyzed. These data were recorded by digital seismograph PDAS-100 and analyzed by DADISP software. Finally, blasting parameters, such as explosive weight and type, distance between the structures and blasting site, blasting delays, affecting ground vibration are reviewed and their influence on peak particle velocity (PPV) are studied. Based on this study, suitable detonation delays and explosive type is determined. Considering these data, a graph of PPV versus scaled distance for Sarcheshmeh copper mine is prepared, by the help of which, safe distance for structures and accordingly explosive quantity could be determined.

  18. Aging of civil explosives (Poster)

    NARCIS (Netherlands)

    Krabbendam-La Haye, E.L.M.; Klerk, W.P.C. de; Hoen, C. 't; Krämer, R.E.

    2014-01-01

    For the Dutch MoD and police, TNO composed sets with different kinds of civil explosives to train their detection dogs. The manufacturer of these explosives guarantees several years of stability of these explosives. These sets of explosives are used under different conditions, like temperature and

  19. Prevention and suppression of explosions in gas-air and dust-air mixtures using powder aerosol-inhibitor

    Energy Technology Data Exchange (ETDEWEB)

    Krasnyansky, M. [Donetsk National Technical University of Ukraine, Donetsk (Ukraine)

    2006-11-15

    The prevention and suppression of explosions is a very topical field of research because annually hundreds of coal mine workers became their victims. In this research a very effective powder 'powder for suppression of explosions' ('PSE') for the suppression of explosions has been developed and tested. The experiments on suppression of explosions of a methane-air mixture (MAM) at a laboratory conditions using 'PSE'-powder have been carried out. The possibility of lowering the power of coal-dust explosion with the help of a 'PSE'-powder has been investigated. The feasibility of almost instantaneous disperse of powders using intentionally created mini-explosions (ammonal) was investigated. The barrel-suppressor of explosion in the experimental adit (tunnel) was studied and the large-scale tests for suppression of MAM-explosions in experimental adit were also subjects of study.

  20. Parametric Explosion Spectral Model

    Energy Technology Data Exchange (ETDEWEB)

    Ford, S R; Walter, W R

    2012-01-19

    Small underground nuclear explosions need to be confidently detected, identified, and characterized in regions of the world where they have never before occurred. We develop a parametric model of the nuclear explosion seismic source spectrum derived from regional phases that is compatible with earthquake-based geometrical spreading and attenuation. Earthquake spectra are fit with a generalized version of the Brune spectrum, which is a three-parameter model that describes the long-period level, corner-frequency, and spectral slope at high-frequencies. Explosion spectra can be fit with similar spectral models whose parameters are then correlated with near-source geology and containment conditions. We observe a correlation of high gas-porosity (low-strength) with increased spectral slope. The relationship between the parametric equations and the geologic and containment conditions will assist in our physical understanding of the nuclear explosion source.

  1. Explosive Components Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The 98,000 square foot Explosive Components Facility (ECF) is a state-of-the-art facility that provides a full-range of chemical, material, and performance analysis...

  2. Intermittent Explosive Disorder

    Directory of Open Access Journals (Sweden)

    Lut Tamam

    2011-09-01

    Full Text Available Intermittent explosive disorder is an impulse control disorder characterized by the occurrence of discrete episodes of failure to resist aggressive impulses that result in violent assault or destruction of property. Though the prevalence intermittent explosive disorder has been reported to be relatively rare in frontier studies on the field, it is now common opinion that intermittent explosive disorder is far more common than previously thought especially in clinical psychiatry settings. Etiological studies displayed the role of both psychosocial factors like childhood traumas and biological factors like dysfunctional neurotransmitter systems and genetics. In differential diagnosis of the disorder, disorders involving agression as a symptom such as alcohol and drug intoxication, antisocial and borderline personality disorders, personality changes due to general medical conditions and behavioral disorder should be considered. A combination of pharmacological and psychotherapeutic approaches are suggested in the treatment of the disorder. This article briefly reviews the historical background, diagnostic criteria, epidemiology, etiology and treatment of intermittent explosive disorder.

  3. 75 FR 5545 - Explosives

    Science.gov (United States)

    2010-02-03

    ....gov . This Federal Register notice, as well as news releases and other relevant information, are also..., Tobacco, Firearms and Explosives (ATF) regulates the import, manufacture, distribution, and storage of...

  4. Ammonium nitrate explosion hazards

    Directory of Open Access Journals (Sweden)

    Negovanović Milanka

    2015-01-01

    Full Text Available Ammonium nitrate (AN primarily is used as a fertilizer but it is also very important compound in the production of industrial explosives. The application of ammonium nitrate in the production of industrial explosives was related with the early era of Nobel dynamite and widely increased with the appearance of blasting agents such as ANFO and Slurry, in the middle of the last Century. Throughout the world millions of tons of ammonium nitrate are produced annually and handled without incident. Although ammonium nitrate generally is used safely, accidental explosions involving AN have high impact resulting in loss of lives and destruction of property. The paper presents the basic properties of ammonium nitrate as well as hazards in handling of ammonium nitrate in order to prevent accidents. Several accidents with explosions of ammonium nitrate resulted in catastrophic consequences are listed in the paper as examples of non-compliance with prescribed procedures.

  5. Explosion suppression system

    Science.gov (United States)

    Sapko, Michael J.; Cortese, Robert A.

    1992-01-01

    An explosion suppression system and triggering apparatus therefor are provided for quenching gas and dust explosions. An electrically actuated suppression mechanism which dispenses an extinguishing agent into the path ahead of the propagating flame is actuated by a triggering device which is light powered. This triggering device is located upstream of the propagating flame and converts light from the flame to an electrical actuation signal. A pressure arming device electrically connects the triggering device to the suppression device only when the explosion is sensed by a further characteristic thereof beside the flame such as the pioneer pressure wave. The light powered triggering device includes a solar panel which is disposed in the path of the explosion and oriented between horizontally downward and vertical. Testing mechanisms are also preferably provided to test the operation of the solar panel and detonator as well as the pressure arming mechanism.

  6. Shock waves & explosions

    CERN Document Server

    Sachdev, PL

    2004-01-01

    Understanding the causes and effects of explosions is important to experts in a broad range of disciplines, including the military, industrial and environmental research, aeronautic engineering, and applied mathematics. Offering an introductory review of historic research, Shock Waves and Explosions brings analytic and computational methods to a wide audience in a clear and thorough way. Beginning with an overview of the research on combustion and gas dynamics in the 1970s and 1980s, the author brings you up to date by covering modeling techniques and asymptotic and perturbative methods and ending with a chapter on computational methods.Most of the book deals with the mathematical analysis of explosions, but computational results are also included wherever they are available. Historical perspectives are provided on the advent of nonlinear science, as well as on the mathematical study of the blast wave phenomenon, both when visualized as a point explosion and when simulated as the expansion of a high-pressure ...

  7. Explosive Welding with Nitroguanidine.

    Science.gov (United States)

    Sadwin, L D

    1964-03-13

    By using the explosive nitroguanidine, continuous welds can be made between similar and dissimilar metals. Since low detonation pressures are attainable, pressure transfer media are not required between the explosive and the metal surface. The need for either a space or an angle between the metals is eliminated, and very low atmospheric pressures are not required. Successful welds have been made between tantalum and 4140 steel, 3003H14 aluminum and 4140 steel, and 304 stainless steel and 3003H14 aluminum.

  8. Overview of Explosive Initiators

    Science.gov (United States)

    2015-11-01

    important characteristics of an effective primary explosive is an extremely swift deflagration to detonation transition, meaning that once the... Taylor , G. W. C., Napier, S. E., "Preparation of Explosive Substances Containing Carboxymethyl Cellulose," U.S. Patent 3,291,664, 1966. 8 Perich, A...Rinkenbach, W. H., "Study of the Action of Lead Azide on Copper," U.S. Army ARDEC, Picatinny Arsenal, NJ, Technical Report No. 1152, 1942. 11 Taylor , G. W

  9. Handbook of HE (High Explosives) Explosive Effects

    Science.gov (United States)

    1986-04-11

    uPcup SI.B iPip P 3 [ xpI os i or ,tf fects, Lx’i Osions In Air,6 19 6T~lT’ Explosions, Airblast - 19 ABSTRAC.T ’Continuje on "uri~ee it neczessary and...AIR FORCE INSTITUTE OF TECHNOLOGY/EN ATTN: MAT 0323 ATTN- LIURARY/AFIT/LDEE NAVAL OCEAN SYSTEMS CENTER AIR FORCE LOGISTICS COMMAND ATTN: CODE 825

  10. How CSIR research aids mining industry

    Energy Technology Data Exchange (ETDEWEB)

    Vorster, H.

    1987-04-01

    The paper outlines supporting services to mining by the Council for Scientific and Industrial Research (CSIR) in South Africa. At present three CSIR institutes are actively involved in the programme of the Coal Mining Research Controlling Council (CMRCC). The use of an ultra-modern blasting tunnel to determine the explosive characteristics of South African coal types is considered as well as investigations to determine the influence of strata conditions on the behaviour of different types of roof bolts. The work of the Strength Mechanics Division in checking design and cause of structural failures of mining equipment and the modernization of the coal preparation research plant is described.

  11. Measurement of Naval Ship Responses to Underwater Explosion Shock Loadings

    Directory of Open Access Journals (Sweden)

    Il-Kwon Park

    2003-01-01

    Full Text Available The shock-resistance capability of battle ships against a non-contact underwater explosion (UNDEX is a very critical factor of survivability. In July 1987 and April 2000, we successfully conducted UNDEX shock tests for a coastal mine hunter (MHC and a mine sweeper/hunter (MSH of Republic of Korea Navy (ROKN, at the Chinhae bay, Korea. Test planning for conducting these shock tests included responsibilities, methods, and procedures. Test instruments were developed and tested on a drop shock machine to confirm availability in the actual shock tests with emphasis on shock resistance, remote control and reliability. All vital systems of the ships were confirmed to be capable of normal operational condition without significant damages during the explosion shot. By analyzing the test results, the tactical operational safety zone of the ships in underwater explosion environments was estimated. In this paper, we described the results of measurement of naval ship responses to underwater explosion shock loadings including test planning, sensor locations, data reduction, explosive devices, instrumentation and damage assessments of MSH.

  12. 49 CFR 172.522 - EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3... INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Placarding § 172.522 EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards. (a) Except for size and color, the EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3...

  13. Chemical industrial production and applied chemistry of metals and nonmetals in educational program of chemistry in elementary school

    Directory of Open Access Journals (Sweden)

    Cvjetićanin Stanko M.

    2009-01-01

    Full Text Available In this paper a part of the model of the curriculum, which should improve chemical education in primary schools is presented. The implemented module refers to metals and non-metals in the fields of applied chemistry and chemical industry. Contents of the curriculum from 1974 to 2004 are considered. The quantity and quality of the pupils' knowledge are analyzed. The research showed that the pupils' knowledge is low. The module is implemented for the sake of overcoming the observed drawbacks in the curriculum, which should facilitate further chemical education, especially in the field of chemical technology. Contents of the curriculum, ways of implementation of the contents, and methods for evaluation of the pupils' knowledge are proposed considering the results of the research. For this purpose the method of descriptive analysis and statistical methods are used.

  14. Non-metal doped TiO2 nanotube arrays for high efficiency photocatalytic decomposition of organic species in water

    Science.gov (United States)

    Szkoda, Mariusz; Siuzdak, Katarzyna; Lisowska-Oleksiak, Anna

    2016-10-01

    Titanium dioxide is a well-known photoactive semiconductor with a variety of possible applications. The procedure of pollutant degradation is mainly performed using TiO2 powder suspension. It can also be exploited an immobilized catalyst on a solid support. Morphology and chemical doping have a great influence on TiO2 activity under illumination. Here we compare photoactivity of titania nanotube arrays doped with non-metal atoms: nitrogen, iodine and boron applied for photodegradation of organic dye - methylene blue and terephtalic acid. The doped samples act as a much better photocatalyst in the degradation process of methylene blue and lead to the formation of much higher amount of hydroxyl radicals (•OH) than undoped TiO2 nanotube arrays. The use of a catalyst active under solar light illumination in the form of thin films on a stable substrate can be scaled up for an industrial application.

  15. Enhanced hydrogen desorption properties of magnesium hydride by coupling non-metal doping and nano-confinement

    Science.gov (United States)

    He, Daliang; Wang, Yulong; Wu, Chengzhang; Li, Qian; Ding, Weizhong; Sun, Chenghua

    2015-12-01

    Magnesium hydride (MgH2) offers excellent capacity to store hydrogen, but it suffers from the high desorption temperature (>283 °C for starting release hydrogen). In this work, we calculated the hydrogen desorption energy of Mg76H152 clusters with/without non-metal dopants by density functional theory method. Phosphorus (P), as identified as the best dopant, can reduce the reaction energy for releasing one hydrogen molecule from 0.75 eV (bulk MgH2) to 0.20 eV. Inspired by the calculation, P-doped ordered mesoporous carbon (CMK-3) was synthesized by one-step method and employed as the scaffold for loading MgH2 nanoparticles, forming MgH2@P/CMK-3. Element analysis shows that phosphorus dopants have been incorporated into the CMK-3 scaffold and magnesium and phosphorus elements are well-distributed in carbon scaffold hosts. Tests of hydrogen desorption confirmed that P-doping can remarkably enhance the hydrogen release properties of nanoconfined MgH2 at low temperature, specifically ˜1.5 wt. % H2 released from MgH2@P/CMK-3 below 200 °C. This work, based on the combination of computational calculations and experimental studies, demonstrated that the combined approach of non-metal doping and nano-confinement is promising for enhancing the hydrogen desorption properties of MgH2, which provides a strategy to address the challenge of hydrogen desorption from MgH2 at mild operational conditions.

  16. Explosive welding of pipes

    Energy Technology Data Exchange (ETDEWEB)

    Drennov, O.; Burtseva, O.; Kitin, A. [Russian Federal Nuclear Center, Sarov (Russian Federation)

    2006-08-15

    Arrangement of pipelines for the transportation of oil and gas is a complicated problem. In this paper it is suggested to use the explosive welding method to weld pipes together. This method is rather new. This method can be advantageous (saving material and physical resources) comparing to its static analogs (electron-beam welding, argon-arc welding, plasma welding, gas welding, etc.), in particular, in hard-to-reach areas due to their geographic and climatic conditions. We suggest to perform explosive welding according to the following scheme: the ends of the 2 pipes are connected, the external surfaces are kept at a similar level. A cylindrical steel layer of diameter larger than the pipe diameter is set around the pipe joint and an explosive charge is placed on its external surface. The basic problem is the elimination of strains and reduction of pipe diameter in the area of the dynamic effect. The suggestion is to use water as filler: the volume of pipes in the area adjacent to the zone of explosive welding is totally filled with water. The principle of non-compressibility of liquid under quasi-dynamic loading is used. In one-dimensional gas dynamic and elastic-plastic calculations we determined non-deformed mass of water. Model experiments with pipes having radii R = 57 mm confirmed results of the calculations and the possibility in principle to weld pipes by explosion with use of water as filler.

  17. Surface explosion cavities

    CERN Document Server

    Benusiglio, Adrien; Clanet, Christophe

    2012-01-01

    We present a fluid dynamics video on cavities created by explosions of firecrackers at the water free surface. We use three types of firecrackers containing 1, 1.3 and 5 g of flash powder. The firecrackers are held with their center at the surface of water in a cubic meter pool. The movies are recorded from the side with a high-speed video camera. Without confinement the explosion produces an hemispherical cavity. Right after the explosion this cavity grows isotropically, the bottom then stops while the sides continue to expand. In the next phase the bottom of the cavity accelerates backwards to the surface. During this phase the convergence of the flow creates a central jet that rises above the free surface. In the last part of the video the explosion is confined in a vertical open tube made of glass and of centimetric diameter. The explosion creates a cylindrical cavity that develops towards the free end of the tube. Depending on the charge, the cavity can either stop inside the tube or at its exit, but nev...

  18. Explosion containment device

    Science.gov (United States)

    Benedick, William B.; Daniel, Charles J.

    1977-01-01

    The disclosure relates to an explosives storage container for absorbing and containing the blast, fragments and detonation products from a possible detonation of a contained explosive. The container comprises a layer of distended material having sufficient thickness to convert a portion of the kinetic energy of the explosion into thermal energy therein. A continuous wall of steel sufficiently thick to absorb most of the remaining kinetic energy by stretching and expanding, thereby reducing the momentum of detonation products and high velocity fragments, surrounds the layer of distended material. A crushable layer surrounds the continuous steel wall and accommodates the stretching and expanding thereof, transmitting a moderate load to the outer enclosure. These layers reduce the forces of the explosion and the momentum of the products thereof to zero. The outer enclosure comprises a continuous pressure wall enclosing all of the layers. In one embodiment, detonation of the contained explosive causes the outer enclosure to expand which indicates to a visual observer that a detonation has occurred.

  19. Novel high explosive compositions

    Science.gov (United States)

    Perry, D.D.; Fein, M.M.; Schoenfelder, C.W.

    1968-04-16

    This is a technique of preparing explosive compositions by the in-situ reaction of polynitroaliphatic compounds with one or more carboranes or carborane derivatives. One or more polynitroaliphatic reactants are combined with one or more carborane reactants in a suitable container and mixed to a homogeneous reaction mixture using a stream of inert gas or conventional mixing means. Ordinarily the container is a fissure, crack, or crevice in which the explosive is to be implanted. The ratio of reactants will determine not only the stoichiometry of the system, but will effect the quality and quantity of combustion products, the explosive force obtained as well as the impact sensitivity. The test values can shift with even relatively slight changes or modifications in the reaction conditions. Eighteen illustrative examples accompany the disclosure. (46 claims)

  20. A real explosion: the requirement of steam explosion pretreatment.

    Science.gov (United States)

    Yu, Zhengdao; Zhang, Bailiang; Yu, Fuqiang; Xu, Guizhuan; Song, Andong

    2012-10-01

    The severity factor is a common term used in steam explosion (SE) pretreatment that describes the combined effects of the temperature and duration of the pretreatment. However, it ignores the duration of the explosion process. This paper describes a new parameter, the explosion power density (EPD), which is independent of the severity factor. Furthermore, we present the adoption of a 5m(3) SE model for a catapult explosion mode, which completes the explosion within 0.0875 s. The explosion duration ratio of this model to a conventional model of the same volume is 1:123. The comparison between the two modes revealed a qualitative change by explosion speed, demonstrating that this real explosion satisfied the two requirements of consistency, and suggested a guiding mechanism for the design of SE devices.

  1. High-nitrogen explosives

    Energy Technology Data Exchange (ETDEWEB)

    Naud, D. (Darren); Hiskey, M. A. (Michael A.); Kramer, J. F. (John F.); Bishop, R. L. (Robert L.); Harry, H. H. (Herbert H.); Son, S. F. (Steven F.); Sullivan, G. K. (Gregg K.)

    2002-01-01

    The syntheses and characterization of various tetrazine and furazan compounds offer a different approach to explosives development. Traditional explosives - such as TNT or RDX - rely on the oxidation of the carbon and hydrogen atoms by the oxygen carrying nitro group to produce the explosive energy. High-nitrogen compounds rely instead on large positive heats of formation for that energy. Some of these high-nitrogen compounds have been shown to be less sensitive to initiation (e.g. by impact) when compared to traditional nitro-containing explosives of similar performances. Using the precursor, 3,6-bis-(3,5-dimethylpyrazol-1-yl)-s-tetrazine (BDT), several useful energetic compounds based on the s-tetrazine system have been synthesized and studied. The compound, 3,3{prime}-azobis(6-amino-s-tetrazine) or DAAT, detonates as a half inch rate stick despite having no oxygen in the molecule. Using perfluoroacetic acid, DAAT can be oxidized to give mixtures of N-oxide isomers (DAAT03.5) with an average oxygen content of about 3.5. This energetic mixture burns at extremely high rates and with low dependency on pressure. Another tetrazine compound of interest is 3,6-diguanidino-s-tetrazine(DGT) and its dinitrate and diperchlorate salts. DGT is easily synthesized by reacting BDT with guanidine in methanol. Using Caro's acid, DGT can be further oxidized to give 3,6-diguanidino-s-tetrazine-1,4-di-N-oxide (DGT-DO). Like DGT, the di-N-oxide can react with nitric acid or perchloric acid to give the dinitrate and the diperchlorate salts. The compounds, 4,4{prime}-diamino-3,3{prime}-azoxyfurazan (DAAF) and 4,4{prime}-diamino-3,3{prime}-azofurazan (DAAzF), may have important future roles in insensitive explosive applications. Neither DAAF nor DAAzF can be initiated by laboratory impact drop tests, yet both have in some aspects better explosive performances than 1,3,5-triamino-2,4,6-trinitrobenzene TATB - the standard of insensitive high explosives. The thermal stability of DAAz

  2. Use of booster fans in underground coal mining to advantage

    Institute of Scientific and Technical Information of China (English)

    Habibi A; Gillies A D S

    2011-01-01

    A booster fan is an underground main fan which is installed in series with a main surface fan and used to boost the air pressure of the ventilation to overcome mine resistance.Currently booster fans are used in several major coal mining countries including the United Kingdom,Australia,Poland and China.In the United States booster fans are prohibited in coal mines although they are used in several metal and non-metal mines.A study has been undertaken to examine alternatives for ventilating an underground room and pillar coal mine system.A feasibility study of a hypothetical situation has shown that current ventilation facilities are incapable of fulfilling mine air requirements in the future due to increased seam methane levels.A current ventilation network model has been prepared and projected to a mine five years plan.“Ventsim visual” software simulations of different possible ventilation options have been conducted in which varying methane levels are found at working faces.The software can also undertake financial simulations and project present value total costs for the options under study.Several scenarios for improving the ventilation situation such as improving main surface fans,adding intake shafts,adding exhaust shafts and utilizing booster fans have been examined.After taking into account the total capital and operating costs for the five years mine plan the booster fan scenarios are recommended as being the best alternatives for further serious consideration by the mine.The optimum option is a properly sized and installed booster fan system that can be used to create safe work conditions,maintain adequate air quantity with lowest cost,generate a reduction in energy consumption and decrease mine system air leakage.

  3. About some aspects of explosion in the soils of artificial structures

    Directory of Open Access Journals (Sweden)

    V. P. Berbushenko

    2013-04-01

    Full Text Available Purpose. To define actual and prospective research guidelines of the destruction of patchy soil masses under the influence of explosions as well as the peculiarities of the explosion waves expansion throughout the boundaries of mediums separation in artificial soils. Methodology. Methods of the study and analysis of published studies on the behavior of soils in the explosion are used, the research methods matching that were used in the investigation of the explosion in natural soils and for research in artificial soil. Findings. The analysis of scientific issues on the topic of soils’ behavior during explosions shows that the natural soils behavior during the explosions in the main explosive for the manufacturing mining-and-explosive works is considered. Originality. The study of nature of artificial soils’ behavior during explosions as well as the consequences prediction and the development of technologies of their liquidation is a very important task for the State Special Transport Service’s subunit. The task is urgent especially considering the current situation of existing threats. Research methods that are offered are not new, but in relation to artificial soils, they were not applied. Practical value. The list and the amount of threats, which exist in the present time, shows that it is necessary to know which consequences the explosions towards the grounds of transport objects may result in.

  4. Application of explosive welding to heat exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Arthur, G.

    1983-10-01

    The subject is discussed under the headings: advantages of explosive welding; principle of explosive welding; explosive welding of tubes; metallurgy of explosive welds (micrographs; microhardness); tubular heat exchangers; plugging; sleeving; retubing; construction of new heat exchangers; thermal sleeves.

  5. The Information Explosion.

    Science.gov (United States)

    Kuhns, William

    Three facets of the media--events, myths, and sales pitches--constitute the most important lines of force taken by the information bombardment which all of us encounter and are influenced by every day. The focus of this book is on the changes created and hastened by this information explosion of the media bombardment: how we can live with them,…

  6. Conventional Weapons Underwater Explosions

    Science.gov (United States)

    1988-12-01

    te that the heat of detonation (the energy available per mass of explosive) is an increasing function of the aluminum content. As shown in Table 2...the heat of detonation of RDX is 6.15 MJ/kg; addition of 30 wt % Al increases this to 10.12 - a factor of 1.64. Fig. 12 indicates a bubble energy

  7. Explosives Safety Competency Study

    Science.gov (United States)

    2010-07-13

    Munitions Systems Journeyman CDC—AFSC 2W051 Combat Ammunition Planning and Production—AFCOMAC Munitions Systems Craftsman Course—AFSC 2W071 Combat...Ammunition Planning and Production—AFCOMAC Munitions Systems Craftsman Course—AFSC 2W071 Navy Basics of Naval Explosives Hazard Control—AMMO-18 b

  8. Explosions during galaxy formation

    Directory of Open Access Journals (Sweden)

    Hugo Martel

    2001-01-01

    Full Text Available As an idealized model of the e ects of energy release by supernovae during galaxy formation, we consider an explosion at the center of a halo which forms at the intersection of laments in the plane of a cosmological pancake by gravitational instability during pancake collapse. Such halos resemble the virialized objects found in N{body simulations in a CDM universe and, therefore, serve as a convenient, scale{free test{bed model for galaxy formation. ASPH=P3M simulations reveal that such explosions are anisotropic. The energy and metals are channeled into the low density regions, away from the pancake plane. The pancake remains essentially undisturbed, even if the explosion is strong enough to blow away all the gas lo- cated inside the halo at the onset of the explosion and reheat the IGM surrounding the pancake. Infall quickly replenishes this ejected gas and gradually restores the gas fraction as the halo mass continues to grow. Estimates of the collapse epoch and SN energy{release for galaxies of di erent mass in the CDM model can re- late these results to scale{dependent questions of blow{out and blow{away and their implication for early IGM heating and metal enrichment and the creation of dark{matter{dominated dwarf galaxies.

  9. Portable raman explosives detection

    Energy Technology Data Exchange (ETDEWEB)

    Moore, David Steven [Los Alamos National Laboratory; Scharff, Robert J [Los Alamos National Laboratory

    2008-01-01

    Recent advances in portable Raman instruments have dramatically increased their application to emergency response and forensics, as well as homeland defense. This paper reviews the relevant attributes and disadvantages of portable Raman spectroscopy, both essentially and instrumentally, to the task of explosives detection in the field.

  10. New explosive seam welding concepts

    Science.gov (United States)

    Bement, L. J.

    1973-01-01

    Recently developed techniques provide totally-confined linear explosive seam welding and produce scarf joint with linear explosive seam welding. Linear ribbon explosives are utilized in making narrow, continuous, airtight joints in variety of aluminum alloys, titanium, copper, brass, and stainless steel.

  11. From Sequential Pattern Mining to Structured Pattern Mining:A Pattern-Growth Approach

    Institute of Scientific and Technical Information of China (English)

    Jia-Wei Han; Jian Pei; Xi-Feng Yan

    2004-01-01

    Sequential pattern mining is an important data mining problem with broad applications. However,it is also a challenging problem since the mining may have to generate or examine a combinatorially explosive number of intermediate subsequences. Recent studies have developed two major classes of sequential pattern mining methods: (1) a candidate generation-and-test approach, represented by (i) GSP, a horizontal format-based sequential pattern mining method, and (ii) SPADE, a vertical format-based method; and (2) a pattern-growth method, represented by PrefixSpan and its further extensions, such as gSpan for mining structured patterns. In this study, we perform a systematic introduction and presentation of the pattern-growth methodology and study its principles and extensions. We first introduce two interesting pattern-growth algorithms, FreeSpan and PrefixSpan, for efficient sequential pattern mining. Then we introduce gSpan for mining structured patterns using the same methodology. Their relative performance in large databases is presented and analyzed. Several extensions of these methods are also discussed in the paper, including mining multi-level, multi-dimensional patterns and mining constraint-based patterns.

  12. Emergency evacuation system for mines

    Institute of Scientific and Technical Information of China (English)

    QIAN Qing-yi; BUDIMAN Jeff; SHEN Jay

    2011-01-01

    There are many potential hazards in the underground mining these include fire,explosion,inundation,roof collapse,toxic gases,chemical pollution,etc.Over past centuries,in US alone,more than 100 000 miners lost their life in different accidents.The primary safety methods used in underground mines concentrate on the monitoring of the hazardous gases,fire detection and ventilation.Using advanced instruments and monitoring techniques have significantly reduced the accidents in the modem mines.However despite the advancement of these monitoring facilities,accidents still occur in underground mining annually in the world,and many miners were killed because they were trapped and unable to escape due to blocked of exit access.Described a new development for the emergency evacuation system in underground mines and analyzed the advantages and disadvantages of the system.It is expected that the new system will greatly improve the emergency exit methods and save more lives in the future.

  13. Big data mining analysis method based on cloud computing

    Science.gov (United States)

    Cai, Qing Qiu; Cui, Hong Gang; Tang, Hao

    2017-08-01

    Information explosion era, large data super-large, discrete and non-(semi) structured features have gone far beyond the traditional data management can carry the scope of the way. With the arrival of the cloud computing era, cloud computing provides a new technical way to analyze the massive data mining, which can effectively solve the problem that the traditional data mining method cannot adapt to massive data mining. This paper introduces the meaning and characteristics of cloud computing, analyzes the advantages of using cloud computing technology to realize data mining, designs the mining algorithm of association rules based on MapReduce parallel processing architecture, and carries out the experimental verification. The algorithm of parallel association rule mining based on cloud computing platform can greatly improve the execution speed of data mining.

  14. 76 FR 35968 - Maintenance of Incombustible Content of Rock Dust in Underground Coal Mines

    Science.gov (United States)

    2011-06-21

    ... relaxation for lower volatile coal. In its experimental studies of the effect of particle size on explosion... approximately 415 active underground bituminous coal mines employing 47,119 miners. Table 1 presents the 415...

  15. Mine seismicity and the Comprehensive Nuclear Test Ban Treaty

    Energy Technology Data Exchange (ETDEWEB)

    Chiappetta, F. [Blasting Analysis International, Allentown, PA (United States); Heuze, F.; Walter, W. [Lawrence Livermore National Lab., CA (United States); Hopler, R. [Powderman Consulting Inc., Oxford, MD (United States); Hsu, V. [Air Force Technical Applications Center, Patrick AFB, FL (United States); Martin, B. [Thunder Basin Coal Co., Wright, WY (United States); Pearson, C. [Los Alamos National Lab., NM (United States); Stump, B. [Southern Methodist Univ., Dallas, TX (United States); Zipf, K. [Univ. of New South Wales (Australia)

    1998-12-09

    Surface and underground mining operations generate seismic ground motions which are created by chemical explosions and ground failures. It may come as a surprise to some that the ground failures (coal bumps, first caves, pillar collapses, rockbursts, etc.) can send signals whose magnitudes are as strong or stronger than those from any mining blast. A verification system that includes seismic, infrasound, hydroacoustic and radionuclide sensors is being completed as part of the CTBT. The largest mine blasts and ground failures will be detected by this system and must be identified as distinct from signals generated by small nuclear explosions. Seismologists will analyze the seismic records and presumably should be able to separate them into earthquake-like and non earthquake-like categories, using a variety of so-called seismic discriminants. Non-earthquake essentially means explosion- or implosion-like. Such signals can be generated not only by mine blasts but also by a variety of ground failures. Because it is known that single-fired chemical explosions and nuclear explosion signals of the same yield give very similar seismic records, the non-earthquake signals will be of concern to the Treaty verification community. The magnitude of the mine-related events is in the range of seismicity created by smaller nuclear explosions or decoupled tests, which are of particular concern under the Treaty. It is conceivable that legitimate mining blasts or some mine-induced ground failures could occasionally be questioned. Information such as shot time, location and design parameters may be all that is necessary to resolve the event identity. In rare instances where the legitimate origin of the event could not be resolved by a consultation and clarification procedure, it might trigger on On-Site Inspection (OSI). Because there is uncertainty in the precise location of seismic event as determined by the International Monitoring System (IMS), the OSI can cover an area of up to 1

  16. Novel methods for detecting buried explosive devices

    Energy Technology Data Exchange (ETDEWEB)

    Kercel, S.W.; Burlage, R.S.; Patek, D.R.; Smith, C.M. [Oak Ridge National Lab., TN (United States); Hibbs, A.D.; Rayner, T.J. [Quantum Magnetics, Inc., San Diego, CA (United States)

    1997-04-01

    Oak Ridge National Laboratory (ORNL) and Quantum Magnetics, Inc. (QM) are exploring novel landmine detection technologies. Technologies considered here include bioreporter bacteria, swept acoustic resonance, nuclear quadrupole resonance (NQR), and semiotic data fusion. Bioreporter bacteria look promising for third-world humanitarian applications; they are inexpensive, and deployment does not require high-tech methods. Swept acoustic resonance may be a useful adjunct to magnetometers in humanitarian demining. For military demining, NQR is a promising method for detecting explosive substances; of 50,000 substances that have been tested, none has an NQR signature that can be mistaken for RDX or TNT. For both military and commercial demining, sensor fusion entails two daunting tasks, identifying fusible features in both present-day and emerging technologies, and devising a fusion algorithm that runs in real-time on cheap hardware. Preliminary research in these areas is encouraging. A bioreporter bacterium for TNT detection is under development. Investigation has just started in swept acoustic resonance as an approach to a cheap mine detector for humanitarian use. Real-time wavelet processing appears to be a key to extending NQR bomb detection into mine detection, including TNT-based mines. Recent discoveries in semiotics may be the breakthrough that will lead to a robust fused detection scheme.

  17. Explosion Testing of a Polycarbonate Safe Haven Wall

    Science.gov (United States)

    Perry, Kyle A.; Meyr, Rex A.

    2016-12-01

    The MINER Act of 2006 was enacted by MSHA following the major mining accidents and required every underground coal mine to install refuge areas to help prevent future fatalities of trapped miners in the event of a disaster where the miners cannot escape. A polycarbonate safe haven wall for use in underground coal mines as component of a complete system was designed and modeled using finite element modeling in ANSYS Explicit Dynamics to withstand the MSHA required 15 psi (103.4 kPa) blast loading spanning 200 milliseconds. The successful design was constructed at a uniform height in both half-width scale and quarter-width scale in the University of Kentucky Explosives Research Team's (UKERT) explosives driven shock tube for verification of the models. The constructed polycarbonate walls were tested multiple times to determine the walls resistance to pressures generated by an explosion. The results for each test were analyzed and averaged to create one pressure versus time waveform which was then imported into ANSYS Explicit Dynamics and modeled to compare results to that which was measured during testing for model validation. This paper summarizes the results.

  18. Incorporating Domain Knowledge into Data Mining Process: An Ontology Based Framework

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    With the explosive growth of data available, there is an urgent need to develop continuous data mining which reduces manual interaction evidently. A novel model for data mining is proposed in evolving environment. First, some valid mining task schedules are generated, and then autonomous and local mining are executed periodically, finally, previous results are merged and refined. The framework based on the model creates a communication mechanism to incorporate domain knowledge into continuous process through ontology service. The local and merge mining are transparent to the end user and heterogeneous data source by ontology. Experiments suggest that the framework should be useful in guiding the continuous mining process.

  19. Theoretical analysis on the casualty of explosion and blower of waste heap with the mutation of intrinsic factors

    Energy Technology Data Exchange (ETDEWEB)

    Jia, H.; Yu, M.; Pan, R.; Yu, S. [Henan Polytechnic University, Jiaozuo (China). College of Safety Science and Engineering

    2008-11-15

    In order to analyse the effects of explosion and disturbance in the waste heap of No. 4 coal mine of Pingdingshan Coal Co. Ltd., the equation of state and specific internal energy equation from the theory of explosion dynamics were applied to find a kinetic model. The evolution process of the explosion and disturbance of the waste heap has the same effect as dynamite being hurled into the explosion centre and the equivalent weight of the dynamite changes with the extent of reaction of the coal, air and water. 9 refs., 2 figs., 3 tabs.

  20. Process mining

    DEFF Research Database (Denmark)

    van der Aalst, W.M.P.; Rubin, V.; Verbeek, H.M.W.

    2010-01-01

    Process mining includes the automated discovery of processes from event logs. Based on observed events (e.g., activities being executed or messages being exchanged) a process model is constructed. One of the essential problems in process mining is that one cannot assume to have seen all possible...... behavior. At best, one has seen a representative subset. Therefore, classical synthesis techniques are not suitable as they aim at finding a model that is able to exactly reproduce the log. Existing process mining techniques try to avoid such “overfitting” by generalizing the model to allow for more...

  1. Development of ammonium nitrate based explosives to optimize explosive properties and explosive welding parameters used during explosion cladding

    Science.gov (United States)

    Hurley, Christoph

    The ability to accurately measure and predict the velocity of explosively driven flyer plates has been a subject of significant work by the explosives community for some time. The majority of this work has focused on the use of high-energy, ideal explosives that are of interest for defense applications. Several attempts have been made to modify the experimental methods developed for these ideal explosives for use in testing low-energy, non-ideal explosive compounds (including industrially useful mixtures of ammonium nitrate, fuels, and additives) with varying degrees of success. The detonation properties of non-ideal explosives are difficult to measure precisely due to the effect of physical, environmental, and geometric factors on the detonation of these materials. The work presented in this document attempts to mitigate the variability inherent in measurements of non-ideal, ammonium nitrate-based explosives by performing testing using charge geometry similar to that used in the industrial process of explosion welding. A method to measure flyer plate velocity with optical high-speed imaging using commercially available equipment is described. Flyer plate velocity data from both experimental measurements and numerical modeling is presented. A new formula for predicting explosive energy based on the detonation velocity of an ammonium nitrate based explosive in a planar geometry is proposed and applied to a theoretical explosive cladding scenario.

  2. Morphology, mechanical and thermal oxidative aging properties of HDPE composites reinforced by nonmetals recycled from waste printed circuit boards.

    Science.gov (United States)

    Yang, Shuangqiao; Bai, Shibing; Wang, Qi

    2016-11-01

    In this study nonmetals recycled from waste printed circuit boards (NPCB) is used as reinforce fillers in high-density polyethylene (HDPE) composites. The morphology, mechanical and thermal oxidative aging properties of NPCB reinforced HDPE composites are assessed and it compared with two other commercial functional filler for the first time. Mechanical test results showed that NPCB could be used as reinforcing fillers in the HDPE composites and mechanical properties especially for stiffness is better than other two commercial fillers. The improved mechanical property was confirmed by the higher aspect ratio and strong interfacial adhesion in scanning electron microscopy (SEM) studies. The heat deflection temperature (HDT) test showed the presence of fiberglass in NPCB can improve the heat resistance of composite for their potential applications. Meanwhile, the oxidation induction time (OIT) and the Fourier transform infrared (FTIR) spectroscopy results showed that NPCB has a near resistance to oxidation as two other commercial fillers used in this paper. The above results show the reuse of NPCB in the HDPE composites represents a promising way for resolving both the environmental pollution and the high-value reuse of resources.

  3. Static, dynamic and electronic properties of expanded fluid mercury in the metal-nonmetal transition range. An ab initio study

    Energy Technology Data Exchange (ETDEWEB)

    CalderIn, L [Research Computing and Cyberinfrastructure, The Pennsylvania State University, University Park, PA 16802 (United States); Gonzalez, L E; Gonzalez, D J, E-mail: david@liq1.fam.cie.uva.es [Departamento de Fisica Teorica, Facultad de Ciencias, Universidad de Valladolid, 47011 Valladolid (Spain)

    2011-09-21

    Fluid Hg undergoes a metal-nonmetal (M-NM) transition when expanded toward a density of around 9 g cm{sup -3}. We have performed ab initio molecular dynamics simulations for several thermodynamic states around the M-NM transition range and the associated static, dynamic and electronic properties have been analyzed. The calculated static structure shows a good agreement with the available experimental data. It is found that the volume expansion decreases the number of nearest neighbors from 10 (near the triple point) to around 8 at the M-NM transition region. Moreover, these neighbors are arranged into two subshells and the decrease in the number of neighbors occurs in the inner subshell. The calculated dynamic structure factors agree fairly well with their experimental counterparts obtained by inelastic x-ray scattering experiments, which display inelastic side peaks. The derived dispersion relation exhibits some positive dispersion for all the states, although its value around the M-NM transition region is not as marked as suggested by the experiment. We have also calculated the electronic density of states, which shows the appearance of a gap at a density of around 8.3 g cm{sup -3}. (paper)

  4. Social big data mining

    CERN Document Server

    Ishikawa, Hiroshi

    2015-01-01

    Social Media. Big Data and Social Data. Hypotheses in the Era of Big Data. Social Big Data Applications. Basic Concepts in Data Mining. Association Rule Mining. Clustering. Classification. Prediction. Web Structure Mining. Web Content Mining. Web Access Log Mining, Information Extraction and Deep Web Mining. Media Mining. Scalability and Outlier Detection.

  5. The propagation law and analysis of gas explosion in U type duct

    Institute of Scientific and Technical Information of China (English)

    YE Qing; LIN Bai-quan; JIA Zhen-zhen; FENG Tao; WANG Hai-qiao

    2008-01-01

    In order to explore the propagation law of gas explosion in U type laneways, the propagation law of flame and shock wave in U type duct were experimentally and theoretically investigated. It is shown that the shock wave takes on the complicated stress state and the flame takes on complicated change rules in the U type duct. The propagation process of gas explosion in bend duct is the mutual action of explosion wave, flame and complicate flow, the destruction in bend surface is especially serious. In the mine exploitation and laneway design, the bend laneway should be avoided, especially continuous bend laneway.

  6. Characteristic Research on Evaporated Explosive Film

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    The evaporation source of evaporated explosive was designed and improved based on the inherent specialties of explosive. The compatibility of explosives and addition agent with evaporation vessels was analyzed. The influence of substrate temperature on explosive was analyzed, the control method of substrate temperature was suggested. The influences of evaporation rate on formation of explosive film and mixed explosive film were confirmed. Optimum evaporation rate for evaporation explosive and the better method for evaporating mixed explosive were presented. The necessary characteristics of the evaporated explosive film were obtained by the research of the differences between the evaporated explosive and other materials.

  7. The classification of explosion-proof protected induction motor into adequate temperature and efficiency class

    Science.gov (United States)

    Brinovar, Iztok; Srpčič, Gregor; Seme, Sebastijan; Štumberger, Bojan; Hadžiselimović, Miralem

    2017-07-01

    This article deals with the classification of explosion-proof protected induction motors, which are used in hazardous areas, into adequate temperature and efficiency class. Hazardous areas are defined as locations with a potentially explosive atmosphere where explosion may occur due to present of flammable gasses, liquids or combustible dusts (industrial plants, mines, etc.). Electric motors and electrical equipment used in such locations must be specially designed and tested to prevent electrical initiation of explosion due to high surface temperature and arcing contacts. This article presents the basic tests of three-phase explosion-proof protected induction motor with special emphasis on the measuring system and temperature rise test. All the measurements were performed with high-accuracy instrumentation and accessory equipment and carried out at the Institute of energy technology in the Electric machines and drives laboratory and Applied electrical engineering laboratory.

  8. Attitudinal Modeling of Affect, Behavior and Cognition: Semantic Mining of Disaster Text Corpus

    Science.gov (United States)

    2010-10-01

    areas in countries all around the Indian Ocean rim, from Indonesia to Somalia. At least 150,000 people died in the disaster, with over 525,000...pollutes the environment, chemical explosion, nuclear explosion, mine explosion and oil spills. Transport Accidents Transport accidents are...whipped past him, but missed. Instead the wave wrapped him around a palm tree, which he struggled to climb. Reaching the top, he could see that his

  9. Explosive bulk charge

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Jacob Lee

    2015-04-21

    An explosive bulk charge, including: a first contact surface configured to be selectively disposed substantially adjacent to a structure or material; a second end surface configured to selectively receive a detonator; and a curvilinear side surface joining the first contact surface and the second end surface. The first contact surface, the second end surface, and the curvilinear side surface form a bi-truncated hemispherical structure. The first contact surface, the second end surface, and the curvilinear side surface are formed from an explosive material. Optionally, the first contact surface and the second end surface each have a substantially circular shape. Optionally, the first contact surface and the second end surface consist of planar structures that are aligned substantially parallel or slightly tilted with respect to one another. The curvilinear side surface has one of a smooth curved geometry, an elliptical geometry, and a parabolic geometry.

  10. Explosive welding underwater

    Energy Technology Data Exchange (ETDEWEB)

    Sim, T.; Allen, K.; Lowes, J.M.

    1980-06-11

    Explosive welding underwater is described. First and second underwater tubular members are assembled together so that the outer surface of the first tubular member and the inner surface of the second tubular member are spaced apart to form an annular cavity. The cavity is closed by seals accommodated in portions of the second tubular member, and is then cleaned and dried and filled with a gas at a pressure greater than the surrounding water pressure. The pressure in the cavity is reduced prior to detonating an explosive charge within the first tubular member to weld the members together. The second tubular member may include portions for receiving further seals so as to subdivide the cavity into a number of zones. The pressures in the zones then can be separately adjusted so as to be able to control the pressure difference a cross each seal. 9 claims.

  11. Explosion of Leidenfrost Droplets

    Science.gov (United States)

    Moreau, Florian; Colinet, Pierre; Dorbolo, Stephane

    2012-11-01

    When a drop is released on a plate heated above a given temperature, a thin layer of vapour can isolate the droplet so that it levitates over the plate. This effect was first reported by Leidenfrost in 1756. However, this fascinating subject remains an active field of research in both fundamental and applied researches. In this work, we focus on what happens when surfactant is added to the drop. The aim is to study the influence of a decrease of the surface tension. Surprisingly, as the droplet evaporates, suddenly it explodes. The evolution of the droplet and the resulting explosion are followed using a high speed camera. We show that when a critical concentration of surfactant is reached inside the drop, a shell of surfactant is formed leading to the explosion. The authors would like to thank FNRS for financial support. This work is financially supported by ODILE project (Contract No. FRFC 2.4623.11).

  12. Explosive Turbulent Magnetic Reconnection

    OpenAIRE

    Higashimori, Katsuaki; Yokoi, Nobumitsu; Hoshino, Masahiro

    2013-01-01

    We report simulation results for turbulent magnetic reconnection obtained using a newly developed Reynolds-averaged magnetohydrodynamics model. We find that the initial Harris current sheet develops in three ways, depending on the strength of turbulence: laminar reconnection, turbulent reconnection, and turbulent diffusion. The turbulent reconnection explosively converts the magnetic field energy into both kinetic and thermal energy of plasmas, and generates open fast reconnection jets. This ...

  13. Hydrogeochemistry and microbiology of mine drainage: An update

    Science.gov (United States)

    Nordstrom, D. Kirk; Blowes, D.W; Ptacek, C.J.

    2015-01-01

    The extraction of mineral resources requires access through underground workings, or open pit operations, or through drillholes for solution mining. Additionally, mineral processing can generate large quantities of waste, including mill tailings, waste rock and refinery wastes, heap leach pads, and slag. Thus, through mining and mineral processing activities, large surface areas of sulfide minerals can be exposed to oxygen, water, and microbes, resulting in accelerated oxidation of sulfide and other minerals and the potential for the generation of low-quality drainage. The oxidation of sulfide minerals in mine wastes is accelerated by microbial catalysis of the oxidation of aqueous ferrous iron and sulfide. These reactions, particularly when combined with evaporation, can lead to extremely acidic drainage and very high concentrations of dissolved constituents. Although acid mine drainage is the most prevalent and damaging environmental concern associated with mining activities, generation of saline, basic and neutral drainage containing elevated concentrations of dissolved metals, non-metals, and metalloids has recently been recognized as a potential environmental concern. Acid neutralization reactions through the dissolution of carbonate, hydroxide, and silicate minerals and formation of secondary aluminum and ferric hydroxide phases can moderate the effects of acid generation and enhance the formation of secondary hydrated iron and aluminum minerals which may lessen the concentration of dissolved metals. Numerical models provide powerful tools for assessing impacts of these reactions on water quality.

  14. Explosive Welding of Pipes

    Science.gov (United States)

    Drennov, Oleg; Drennov, Andrey; Burtseva, Olga

    2013-06-01

    For connection by welding it is suggested to use the explosive welding method. This method is rather new. Nevertheless, it has become commonly used among the technological developments. This method can be advantageous (saving material and physical resources) comparing to its statical analogs (electron-beam welding, argon-arc welding, plasma welding, gas welding, etc.), in particular, in hard-to-reach areas due to their geographic and climatic conditions. Explosive welding of cylindrical surfaces is performed by launching of welded layer along longitudinal axis of construction. During this procedure, it is required to provide reliable resistance against radial convergent strains. The traditional method is application of fillers of pipe cavity, which are dense cylindrical objects having special designs. However, when connecting pipes consecutively in pipelines by explosive welding, removal of the fillers becomes difficult and sometimes impossible. The suggestion is to use water as filler. The principle of non-compressibility of liquid under quasi-dynamic loading is used. In one-dimensional gasdynamic and elastic-plastic calculations we determined non-deformed mass of water (perturbations, which are moving in the axial direction with sound velocity, should not reach the layer end boundaries for 5-7 circulations of shock waves in the radial direction). Linear dimension of the water layer from the zone of pipe coupling along axis in each direction is >= 2R, where R is the internal radius of pipe.

  15. Improving mine safety technology and training in the U.S. recommendations of the Mine Safety Technology and Training Commission

    Institute of Scientific and Technical Information of China (English)

    GRAYSON R. Larry

    2008-01-01

    The key issues studied focused on underground coal mining and included (1)prevention of explosions in sealed areas, (2) better emergency preparedness and re-sponse, (3) improvement of miners' ability to escape, (4) better protection of miners beforeand after a fire or explosion, (5) improved provision of oxygen, and (6) development andimplementation of more robust post-incident communication. The U.S. Congress passedthe Mine Improvement and New Emergency Response Act of 2006, which mandated newlaws to address the issues. Concurrent with investigations and congressional deliberations,the National Mining Association formed the independent Mine Safety Technology andTraining Commission to study the state-of-the-art relative to technology and training thatcould address the vulnerabilities exposed by the mine disasters. As discussed, the reportoutlined persistent vulnerabilities linked with significant hazards in underground coal mines,and made recommendations to provide a path for addressing them. Overall the commis-sion report made 75 recommendations in the areas of risk-based design and management,communications technology, emergency response and mine rescue procedures, trainingfor preparedness, and escape and protection strategies. In its deliberations, the commis-sion importantly noted that mine safety in the U.S. needs to follow a new paradigm for en-suring mine safety and developing a culture of prevention that supports safe production atthe business core. In the commission's viewpoint, the bottom line in protecting coal minersis not only adopting a culture of prevention but also systematically pursuing mitigation ofsignificant risks.

  16. Theoretical Calculation for the Explosion Temperature of Expanded Ammonium Nitrate Explosives%膨化硝铵炸药爆温的理论计算分析

    Institute of Scientific and Technical Information of China (English)

    刘丽梅; 杨林; 夏建才

    2011-01-01

    The explosion temperature of expanded ammonium nitrate explosives are calculated in this paper. The result shows that the explosion temperature of opencast expanded ammonium nitrate explosives, rock expanded ammonium nitrate explosives, class Ⅰ and Ⅱ coal mine permissible expanded ammonium nitrate explosives is 2 722 K, 2 771 K,2 544 K,2 486 K respectively. The explosion temperature of rock expanded ammonium nitrate explosives in assumed formula are calculated when the ratio of paraffin with diesel oil in composite fuel oil are different. According to the calculation results,it can be seen that the explosion heat and explosion temperature of rock expanded ammonium nitrate explosives increase weakly with the increasing of contents of paraffin in composite fuel oil.%运用B-W法确定膨化硝铵炸药的爆炸反应方程式,用盖斯定律计算定容爆热,用加权法计算爆炸产物的摩尔定容热容,研究计算得出露天膨化硝铵炸药、岩石膨化硝铵炸药、一级、二级煤矿许用膨化硝铵炸药的爆温依次为2722 K、2 771K、2544K和2 486 K.同时计算分析了复合油相中不同的石蜡与柴油的混合比例对岩石膨化硝铵炸药爆热、爆温数据的影响情况,计算结果表明复合油相组成的变化对岩石膨化硝铵炸药爆热、爆温的影响不明显.

  17. Improvised explosive devices: pathophysiology, injury profiles and current medical management.

    Science.gov (United States)

    Ramasamy, A; Hill, A M; Clasper, J C

    2009-12-01

    The improvised explosive device (IED), in all its forms, has become the most significant threat to troops operating in Afghanistan and Iraq. These devices range from rudimentary home made explosives to sophisticated weapon systems containing high-grade explosives. Within this broad definition they may be classified as roadside explosives and blast mines, explosive formed pojectile (EFP) devices and suicide bombings. Each of these groups causeinjury through a number of different mechanisms and can result in vastly different injury profiles. The "Global War on Terror" has meant that incidents which were previously exclusively seen in conflict areas, can occur anywhere, and clinicians who are involved in emergency trauma care may be required to manage casualties from similar terrorist attacks. An understanding of the types of devices and their pathophysiological effects is necessary to allow proper planning of mass casualty events and to allow appropriate management of the complex poly-trauma casualties they invariably cause. The aim of this review article is to firstly describe the physics and injury profile from these different devices and secondly to present the current clinical evidence that underpins their medical management.

  18. Fibre Optics In Coal Mining

    Science.gov (United States)

    Cooper, Paul

    1984-08-01

    Coal mines have a number of unique problems which affect the use of fibre optic technology. These include a potentially explosive atmosphere due to the evolution of methane from coal, and a dirty environment with no cleaning facilities readily available. Equipment being developed by MRDE to allow the exploitation of optical fibres underground includes: A hybrid electrical/fibre optic connector for the flexible power trailing cable of the coal-face shearer; An Intrinsically Safe (IS) pulsed laser transmitter using Frequency Shift Key (FSK) data modulation; An IS Avalanche Photo Diode Receiver suitable for pulsed & continuous wave optical signals; A mine shaft and roadway cable/ connector system incorporating low loss butt-splices and preterminated demountable connectors.

  19. Data mining concepts and techniques

    CERN Document Server

    Han, Jiawei

    2005-01-01

    Our ability to generate and collect data has been increasing rapidly. Not only are all of our business, scientific, and government transactions now computerized, but the widespread use of digital cameras, publication tools, and bar codes also generate data. On the collection side, scanned text and image platforms, satellite remote sensing systems, and the World Wide Web have flooded us with a tremendous amount of data. This explosive growth has generated an even more urgent need for new techniques and automated tools that can help us transform this data into useful information and knowledge.Like the first edition, voted the most popular data mining book by KD Nuggets readers, this book explores concepts and techniques for the discovery of patterns hidden in large data sets, focusing on issues relating to their feasibility, usefulness, effectiveness, and scalability. However, since the publication of the first edition, great progress has been made in the development of new data mining methods, systems, and app...

  20. Data mining for social network data

    CERN Document Server

    Memon, Nasrullah; Hicks, David L; Chen, Hsinchun

    2010-01-01

    Driven by counter-terrorism efforts, marketing analysis and an explosion in online social networking in recent years, data mining has moved to the forefront of information science. This proposed Special Issue on ""Data Mining for Social Network Data"" will present a broad range of recent studies in social networking analysis. It will focus on emerging trends and needs in discovery and analysis of communities, solitary and social activities, and activities in open fora, and commercial sites as well. It will also look at network modeling, infrastructure construction, dynamic growth and evolution

  1. Surface Mines, Other - Longwall Mining Panels

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Coal mining has occurred in Pennsylvania for over a century. A method of coal mining known as Longwall Mining has become more prevalent in recent decades. Longwall...

  2. Coal Mines, Active - Longwall Mining Panels

    Data.gov (United States)

    NSGIC GIS Inventory (aka Ramona) — Coal mining has occurred in Pennsylvania for over a century. A method of coal mining known as Longwall Mining has become more prevalent in recent decades. Longwall...

  3. Nanosensors for trace explosive detection

    OpenAIRE

    2008-01-01

    Selective and sensitive detection of explosives is very important in countering terrorist threats. Detecting trace explosives has become a very complex and expensive endeavor because of a number of factors, such as the wide variety of materials that can be used as explosives, the lack of easily detectable signatures, the vast number of avenues by which these weapons can be deployed, and the lack of inexpensive sensors with high sensitivity and selectivity. High sensitivity and selectivity, co...

  4. Study on dangers of methane in the gob of fully mechanized caving mining

    Institute of Scientific and Technical Information of China (English)

    LU Guang-li; WU Li-rong; ZOU De-yun

    2007-01-01

    Divided the gob gas in different types according to falling structure and spatial patterns of gob of the fully mechanized caving mining and analyzed its main form of harm.This passage preliminarily studied the law of unusual gush of gob gas of the fully mechanized caving mining. According to the basic condition for the gas explosion, made comprehensive analysis and appraisal about the oxygen condition, gas concentration distribute and fire source conditions. And find that there is the dangerous district of gas explosion in a certain area of the producing gob and give the three zone theory of gob gas explosion.

  5. Zonal disintegration of rocks around underground mines, part III: theoretical concepts

    Energy Technology Data Exchange (ETDEWEB)

    Shemyakin, E.I.; Fisenko, G.L.; Kurlenya, M.V.; Oparin, V.N.; Reva, V.N.; Glushikhin, F.P.; Rozenbaum, M.A.; Tropp, E.A.; Kuznetsov, Yu.D.

    1987-11-01

    The authors construct a nonlinear mathematical model describing the fracture mechanics of coal seams during explosive fracturing and drilling operations in underground mining. The model incorporates stress distribution and relaxation analysis and crack propagation along with other mechanical properties and can be implemented in determining the required layout and strength of support systems and the advance of the mine working.

  6. Explosive turbulent magnetic reconnection.

    Science.gov (United States)

    Higashimori, K; Yokoi, N; Hoshino, M

    2013-06-21

    We report simulation results for turbulent magnetic reconnection obtained using a newly developed Reynolds-averaged magnetohydrodynamics model. We find that the initial Harris current sheet develops in three ways, depending on the strength of turbulence: laminar reconnection, turbulent reconnection, and turbulent diffusion. The turbulent reconnection explosively converts the magnetic field energy into both kinetic and thermal energy of plasmas, and generates open fast reconnection jets. This fast turbulent reconnection is achieved by the localization of turbulent diffusion. Additionally, localized structure forms through the interaction of the mean field and turbulence.

  7. Asteroid mining

    Science.gov (United States)

    Gertsch, Richard E.

    1992-01-01

    The earliest studies of asteroid mining proposed retrieving a main belt asteroid. Because of the very long travel times to the main asteroid belt, attention has shifted to the asteroids whose orbits bring them fairly close to the Earth. In these schemes, the asteroids would be bagged and then processed during the return trip, with the asteroid itself providing the reaction mass to propel the mission homeward. A mission to one of these near-Earth asteroids would be shorter, involve less weight, and require a somewhat lower change in velocity. Since these asteroids apparently contain a wide range of potentially useful materials, our study group considered only them. The topics covered include asteroid materials and properties, asteroid mission selection, manned versus automated missions, mining in zero gravity, and a conceptual mining method.

  8. Process mining

    DEFF Research Database (Denmark)

    van der Aalst, W.M.P.; Rubin, V.; Verbeek, H.M.W.

    2010-01-01

    Process mining includes the automated discovery of processes from event logs. Based on observed events (e.g., activities being executed or messages being exchanged) a process model is constructed. One of the essential problems in process mining is that one cannot assume to have seen all possible...... behavior. At best, one has seen a representative subset. Therefore, classical synthesis techniques are not suitable as they aim at finding a model that is able to exactly reproduce the log. Existing process mining techniques try to avoid such “overfitting” by generalizing the model to allow for more...... behavior. This generalization is often driven by the representation language and very crude assumptions about completeness. As a result, parts of the model are “overfitting” (allow only for what has actually been observed) while other parts may be “underfitting” (allowfor much more behavior without strong...

  9. Controlled by Distant Explosions

    Science.gov (United States)

    2007-03-01

    VLT Automatically Takes Detailed Spectra of Gamma-Ray Burst Afterglows Only Minutes After Discovery A time-series of high-resolution spectra in the optical and ultraviolet has twice been obtained just a few minutes after the detection of a gamma-ray bust explosion in a distant galaxy. The international team of astronomers responsible for these observations derived new conclusive evidence about the nature of the surroundings of these powerful explosions linked to the death of massive stars. At 11:08 pm on 17 April 2006, an alarm rang in the Control Room of ESO's Very Large Telescope on Paranal, Chile. Fortunately, it did not announce any catastrophe on the mountain, nor with one of the world's largest telescopes. Instead, it signalled the doom of a massive star, 9.3 billion light-years away, whose final scream of agony - a powerful burst of gamma rays - had been recorded by the Swift satellite only two minutes earlier. The alarm was triggered by the activation of the VLT Rapid Response Mode, a novel system that allows for robotic observations without any human intervention, except for the alignment of the spectrograph slit. ESO PR Photo 17a/07 ESO PR Photo 17a/07 Triggered by an Explosion Starting less than 10 minutes after the Swift detection, a series of spectra of increasing integration times (3, 5, 10, 20, 40 and 80 minutes) were taken with the Ultraviolet and Visual Echelle Spectrograph (UVES), mounted on Kueyen, the second Unit Telescope of the VLT. "With the Rapid Response Mode, the VLT is directly controlled by a distant explosion," said ESO astronomer Paul Vreeswijk, who requested the observations and is lead-author of the paper reporting the results. "All I really had to do, once I was informed of the gamma-ray burst detection, was to phone the staff astronomers at the Paranal Observatory, Stefano Bagnulo and Stan Stefl, to check that everything was fine." The first spectrum of this time series was the quickest ever taken of a gamma-ray burst afterglow

  10. Data mining

    CERN Document Server

    Gorunescu, Florin

    2011-01-01

    The knowledge discovery process is as old as Homo sapiens. Until some time ago, this process was solely based on the 'natural personal' computer provided by Mother Nature. Fortunately, in recent decades the problem has begun to be solved based on the development of the Data mining technology, aided by the huge computational power of the 'artificial' computers. Digging intelligently in different large databases, data mining aims to extract implicit, previously unknown and potentially useful information from data, since 'knowledge is power'. The goal of this book is to provide, in a friendly way

  11. Mining Review

    Science.gov (United States)

    ,

    2013-01-01

    In 2012, the estimated value of mineral production increased in the United States for the third consecutive year. Production and prices increased for most industrial mineral commodities mined in the United States. While production for most metals remained relatively unchanged, with the notable exception of gold, the prices for most metals declined. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals’ contribution to the GDP increased for the second consecutive year.

  12. Low-Frequency Synthetic Aperture Sonar For Detecting Explosives in Harbors

    NARCIS (Netherlands)

    Beckers, A.L.D.; Vossen, R. van; Vlaming, G.

    2012-01-01

    Naval mines and underwater improvised explosive devices in harbors can halt or block maritime transport, causing local disruptions that can impact national and regional economies considerably. Securing harbors against such threats is implemented in the Netherlands through cooperation between civil a

  13. Development of active guidance systems to overcome problems of disorientation and low visibility following severe explosions.

    CSIR Research Space (South Africa)

    Phillips, HR

    1995-01-01

    Full Text Available The objective of this research project was to review methods of overcoming the disorientation of underground mine workers following an explosion or severe fire. The results of this project indicate that different strategies may be required for fires...

  14. 30 CFR 18.14 - Identification of tested noncertified explosion-proof enclosures.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Identification of tested noncertified explosion-proof enclosures. 18.14 Section 18.14 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... AND ACCESSORIES General Provisions § 18.14 Identification of tested noncertified...

  15. Destruction mechanism of gas explosion to ventilation facilities and automatic recovery technology

    Institute of Scientific and Technical Information of China (English)

    Wang Kai; Jiang Shuguang; Zhang Weiqing; Wu Zhengyan; Shao Hao; Kou Liwen

    2012-01-01

    In order to overcome the heavy casualties caused by gas explosion,we verified the propagation law of shock wave in pipeline and the overpressure distribution of gas explosion by similar experiments according to the analyses of reasons for casualty and ventilation system model destroyed by gas explosion in the mining face.We summarized the gas composition after the explosion and its danger,analyzed the effects of the gas explosion shock wave to ventilation system and facilities and the laws of toxic gas spread and diffusion in the ventilation network after the explosion.We presented a technical proposal to control the smoke and recover the ventilation system after a gas explosion and developed a reserve air door and control system that were embed in the lane,and could close automatically in conditions of no pressure and electricity.The results showed that the reserve air door normally opened and could close automatically controlling the smoke flow and resuming the ventilation system when the gas explosion shock wave destroyed the original shutting air door which resulted in the air short circuit.

  16. Laser machining of explosives

    Science.gov (United States)

    Perry, Michael D.; Stuart, Brent C.; Banks, Paul S.; Myers, Booth R.; Sefcik, Joseph A.

    2000-01-01

    The invention consists of a method for machining (cutting, drilling, sculpting) of explosives (e.g., TNT, TATB, PETN, RDX, etc.). By using pulses of a duration in the range of 5 femtoseconds to 50 picoseconds, extremely precise and rapid machining can be achieved with essentially no heat or shock affected zone. In this method, material is removed by a nonthermal mechanism. A combination of multiphoton and collisional ionization creates a critical density plasma in a time scale much shorter than electron kinetic energy is transferred to the lattice. The resulting plasma is far from thermal equilibrium. The material is in essence converted from its initial solid-state directly into a fully ionized plasma on a time scale too short for thermal equilibrium to be established with the lattice. As a result, there is negligible heat conduction beyond the region removed resulting in negligible thermal stress or shock to the material beyond a few microns from the laser machined surface. Hydrodynamic expansion of the plasma eliminates the need for any ancillary techniques to remove material and produces extremely high quality machined surfaces. There is no detonation or deflagration of the explosive in the process and the material which is removed is rendered inert.

  17. Future challenges for explosive industry vis-a-vis underground coal blasting

    Energy Technology Data Exchange (ETDEWEB)

    Roy, S.K.; Singh, R.R.; Ram, P.; Paul, R.K. [Central Mining Research Institute, Dhanbad (India)

    2002-03-01

    It is apprehended that with contribution of open cast mines in total production of coal going up further, the deterioration trend in coal quality will continue. Production from underground coal mines has to be increased in coming years for sustainable growth of coal industry and to meet the ever increasing power demand. So, to compete with the mechanical cutting of coal, the explosive industry needs a breakthrough in innovativeness, production and uses. The explosive industry and concerned organisations have to accept future challenges in development of safer products, more efficient application technique and strict quality control of products. Change in some of the regulations governing the uses of explosive in underground coal blasting also is called for. 14 refs.

  18. Damage Characteristics of Surrounding Rock Subjected to VCR Mining Blasting Shock

    OpenAIRE

    Nan Jiang; Chuanbo Zhou; Xuedong Luo; Shiwei Lu

    2015-01-01

    For limiting the damage range caused by explosive shock loads in vertical crater retreat (VCR) mining, the blasting damage characteristics of surrounding rock were studied by two methods: numerical simulation and ultrasonic testing. Combined with the mining blasting in Dongguashan Copper Mine of China, the VCR blasting shock characteristics under different conditions are obtained by using LSDYNA. Based on statistical fracture mechanics and damage mechanics theories, a damage constitutive mode...

  19. Explosive Welding for Remote Applications

    Science.gov (United States)

    Bement, L. J.

    1985-01-01

    Explosive seam welding produces up to 100-percent joint strength. Ribbon explosive activated by remote energy source produces metallurgically sound joint. Success of technique verified for joints between like metals and joints between two different metals. Applications include structural assembly in toxic atmospheres and in radioactive or otherwise hazardous environments.

  20. Active Water Explosion Suppression System

    Science.gov (United States)

    2002-06-01

    efficient in eliminating the heat of detonation , thereby eliminating the heat of combustion and the associated burning of explosive by-products in the...efficiency in eliminating the heat of detonation . In any case, the net effect of the water absorbing the detonation energy of the explosive is a major

  1. Introduction to High Explosives Science

    Energy Technology Data Exchange (ETDEWEB)

    Skidmore, Cary Bradford [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Preston, Daniel N. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-11-17

    These are a set of slides for educational outreach to children on high explosives science. It gives an introduction to the elements involved in this science: carbon, hydrogen, nitrogen, and oxygen. Combined, these form the molecule HMX. Many pictures are also included to illustrate explosions.

  2. Explosive welding of undersea pipelines

    Energy Technology Data Exchange (ETDEWEB)

    Stalker, A.W.

    1978-02-01

    The phenomenon of explosive welding has been known informally for many years. A number of investigations reported the occurerence of solid phase bonds as an incidental effect when using high explosives in association with adjacent metal surfaces and probably the earliest formal record was the observation by Carl in 1944 of a bond between two copper discs in contact with a detonator. In 1957 Philipchuk reported what is now recognized as an explosive weld between aluminium channel sections and a steel die when carrying out explosive forming trials. Since then a great deal of development work has resulted in explosive welding becoming a well established manufacturing technique, particularly in the fields of cladding and the joining of tube/tubeplates. In more recent years the process has been extended to the welding of large diameter line pipe materials.

  3. Explosive welding: Principles and potentials

    Energy Technology Data Exchange (ETDEWEB)

    Brasher, D.G.; Butler, D.J. [Northwest Technical Industries, Inc., Sequim, WA (United States)

    1995-03-01

    Explosive welding is a solid-state process in which controlled explosive detonations force two or more metals together at high pressures. The resultant composite system is joined with a high-quality metallurgical bond. Explosive welding (or explosive bonding) is a high-pressure process in which contaminant surface films are plastically jetted off the base metals as a result of the collision of two metals. The time duration involved in the explosive welding event is so short that the reaction zone (or heat affected zone) between the constituent metals is microscopic. During the process, the first few atomic layers of each metal become plasma because of the high velocity of the impact (200 to 500 m/s, 660 to 1,640 ft/s.) The angle of collision causes the plasma to jet in front of the collision point, effectively scrub-cleaning both surfaces, and leaving clean metal behind.

  4. The Scaled Thermal Explosion Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Wardell, J F; Maienschein, J L

    2002-07-05

    We have developed the Scaled Thermal Explosion Experiment (STEX) to provide a database of reaction violence from thermal explosion for explosives of interest. Such data are needed to develop, calibrate, and validate predictive capability for thermal explosions using simulation computer codes. A cylinder of explosive 25, 50 or 100 mm in diameter, is confined in a steel cylinder with heavy end caps, and heated under controlled conditions until reaction. Reaction violence is quantified through non-contact micropower impulse radar measurements of the cylinder wall velocity and by strain gauge data at reaction onset. Here we describe the test concept, design and diagnostic recording, and report results with HMX- and RDX-based energetic materials.

  5. Mining Method

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Young Shik; Lee, Kyung Woon; Kim, Oak Hwan; Kim, Dae Kyung [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

    1996-12-01

    The reducing coal market has been enforcing the coal industry to make exceptional rationalization and restructuring efforts since the end of the eighties. To the competition from crude oil and natural gas has been added the growing pressure from rising wages and rising production cost as the workings get deeper. To improve the competitive position of the coal mines against oil and gas through cost reduction, studies to improve mining system have been carried out. To find fields requiring improvements most, the technologies using in Tae Bak Colliery which was selected one of long running mines were investigated and analyzed. The mining method appeared the field needing improvements most to reduce the production cost. The present method, so-called inseam roadway caving method presently is using to extract the steep and thick seam. However, this method has several drawbacks. To solve the problems, two mining methods are suggested for a long term and short term method respectively. Inseam roadway caving method with long-hole blasting method is a variety of the present inseam roadway caving method modified by replacing timber sets with steel arch sets and the shovel loaders with chain conveyors. And long hole blasting is introduced to promote caving. And pillar caving method with chock supports method uses chock supports setting in the cross-cut from the hanging wall to the footwall. Two single chain conveyors are needed. One is installed in front of chock supports to clear coal from the cutting face. The other is installed behind the supports to transport caved coal from behind. This method is superior to the previous one in terms of safety from water-inrushes, production rate and productivity. The only drawback is that it needs more investment. (author). 14 tabs., 34 figs.

  6. Planning the Mine and Mining the Plan

    Science.gov (United States)

    Boucher, D. S.; Chen, N.

    2016-11-01

    Overview of best practices used in the terrestrial mining industry when developing a mine site towards production. The intent is to guide planners towards an effective and well constructed roadmap for the development of ISRU mining activities. A strawman scenario is presented as an illustration for lunar mining of water ice.

  7. Preliminary study to AP mine neutralisation by EFP impact

    NARCIS (Netherlands)

    Meulman, J.H.

    2004-01-01

    A preliminary study has been conducted into the response of anti-personnel mines at the impact of an Explosively Formed Projectile (EFP). The objective was to obtain a low order reaction (preferably a deflagration) to minimise collateral damage. Further the method should be capable to neutralise min

  8. Condition for Contur Blasting use on Openpit Mines

    OpenAIRE

    Krsmanovic, I; Dambov, Risto

    2010-01-01

    For purpose of obtaining a stable final slope in open pit mines practice, the most common approach is the contour blasting method and investigation of possible applications of various primary blasting methods for purpose of gaining the optimal techno-economical effects. This paper presents one of the contour blasting methods, drilling and blasting parameters, construction of explosive charges and method of initiation.

  9. The interaction of explosively generated plasma with explosives

    Science.gov (United States)

    Tasker, Douglas G.; Whitley, Von H.; Johnson, Carl E.

    2017-01-01

    It has been shown that the temperature of explosively generated plasma (EGP) is of the order of 1 eV and plasma ejecta can be focused to achieve velocities as high as 25 km/s. Proof-of-principle tests were performed to determine if EGP could be used for explosive ordnance demolition and other applications. The goals were: to benignly disable ordnance containing relatively sensitive high performance explosives (PBX-9501); and to investigate the possibility of interrupting an ongoing detonation in a powerful high explosive (again PBX-9501) with EGP. Experiments were performed to establish the optimum sizes of plasma generators for the benign deactivation of high explosives, i.e., the destruction of the ordnance without initiating a detonation or comparable violent event. These experiments were followed by attempts to interrupt an ongoing detonation by the benign disruption of the unreacted explosive in its path. The results were encouraging. First, it was demonstrated that high explosives could be destroyed without the initiation of a detonation or high order reaction. Second, ongoing detonations were successfully interrupted with EGP. [LA-UR-15-25350

  10. Mixing in explosions

    Energy Technology Data Exchange (ETDEWEB)

    Kuhl, A.L.

    1993-12-01

    Explosions always contain embedded turbulent mixing regions, for example: boundary layers, shear layers, wall jets, and unstable interfaces. Described here is one particular example of the latter, namely, the turbulent mixing occurring in the fireball of an HE-driven blast wave. The evolution of the turbulent mixing was studied via two-dimensional numerical simulations of the convective mixing processes on an adaptive mesh. Vorticity was generated on the fireball interface by baroclinic effects. The interface was unstable, and rapidly evolved into a turbulent mixing layer. Four phases of mixing were observed: (1) a strong blast wave phase; (2) and implosion phase; (3) a reshocking phase; and (4) an asymptotic mixing phase. The flowfield was azimuthally averaged to evaluate the mean and r.m.s. fluctuation profiles across the mixing layer. The vorticity decayed due to a cascade process. This caused the corresponding enstrophy parameter to increase linearly with time -- in agreement with homogeneous turbulence calculations of G.K. Batchelor.

  11. Explosion risks from nanomaterials

    Science.gov (United States)

    Bouillard, Jacques; Vignes, Alexis; Dufaud, Olivier; Perrin, Laurent; Thomas, Dominique

    2009-05-01

    Emerging nanomanufactured products are being incorporated in a variety of consumer products ranging from closer body contact products (i.e. cosmetics, sunscreens, toothpastes, pharmaceuticals, clothing) to more remote body-contact products (electronics, plastics, tires, automotive and aeronautical), hence posing potential health and environmental risks. The new field of nanosafety has emerged and needs to be explored now rather than after problems becomes so ubiquitous and difficult to treat that their trend become irreversible. Such endeavour necessitates a transdisciplinary approach. A commonly forgotten and/or misunderstood risk is that of explosion/detonation of nanopowders, due to their high specific active surface areas. Such risk is emphasized and illustrated with the present development of an appropriate risk analysis. For this particular risk, a review of characterization methods and their limitations with regard to nanopowders is presented and illustrated for a few organic and metallic nanopowders.

  12. Soil microflora over the closed Donbas mines

    Energy Technology Data Exchange (ETDEWEB)

    Kurdish, I.K.; Kisten, A.G.; Roi, A.A.; Iakovenko, E.A.; Bezborodov, V.A.

    2005-05-15

    Composition of soil air and microflora in different soil horizons (to 30 cm depth) over some closed Donbas coal mines has been studied. The intensive methane leakages have been found in some soil zones over the closed coal mines. This results in formation of explosive and inflammable gas mixtures. Methane content in soil gas mixtures could vary from trace amounts to 34 %. The essential decrease of oxygen (to 3-4%) and increasing (up to 5 %) of CO2 concentrations that evidences for active microbiological processes in such soils is marked in the latter case. Methanotrophic bacteria involving methane into biogenic cycle are widespread (up to 106 cells per 1 g) in methane-containing soils over the closed coal mines. Microorganisms of different physiological groups in the community with methanotrophic bacteria were found in the given technogenic econiche.

  13. [Soil microflora over the closed Donbas mines].

    Science.gov (United States)

    Kurdish, I K; Kisten', A G; Roĭ, A A; Iakovenko, E A; Bezborodov, V A

    2005-01-01

    Composition of soil air and microflora in different soil horizons (to 30 cm depth) over some closed Donbas coal mines has been studied. The intensive methane leakages have been found in some soil zones over the closed coal mines. This results in formation of explosive and inflammable gas mixtures. Methane content in soil gas mixtures could vary from trace amounts to 34 %. The essential decrease of oxygen (to 3-4%) and increasing (up to 5 %) of CO2 concentrations that evidences for active microbiological processes in such soils is marked in the latter case. Methanotrophic bacteria involving methane into biogenic cycle are widespread (up to 106 cells per 1 g) in methane-containing soils over the closed coal mines. Microorganisms of different physiological groups in the community with methanotrophic bacteria were found in the given technogenic econiche.

  14. 无机非金属材料专业基础实验的教学体会%Experiences to Experiment Teaching of Inorganic Nonmetal Material Engineering

    Institute of Scientific and Technical Information of China (English)

    李宏林; 李明玲; 高华敏

    2015-01-01

    Professional basic experiment of Inorganic Nonmetal Material Engineering is an important teaching in enhancing students’ abilities of comprehending academic courses, and it is very important to foster compositive diathesis and the ability of solving actual problems for students. Some experiences in the Inorganic Nonmetal Material Engineering specialty experiment teaching were summarized. The experimental teaching method was reformed to make students pay attention to preview and participate in the experimental teaching, gather more experimental material to enrich the experimental teaching content, and regulate experiment report writing. The purpose was to improve the inorganic nonmetal material engineering specialty experiment teaching.%无机非金属材料专业基础实验是学生加深理解理论课知识的一个重要的实践教学环节,对培养学生综合素质和解决实际问题能力作用重大。笔者结合无机非金属材料专业基础实验教学经验提出了几点体会。主要从“教学方法改革让学生重视预习并参与实验教学、广集实验原料以及规范实验报告的撰写”等几个方面进行了简单的探讨,以达到提高无机非金属材料工程专业基础实验教学效果的目的。

  15. Sustainable mining management; Gestion minera sostenible

    Energy Technology Data Exchange (ETDEWEB)

    Tejera Oliver, J. L.

    2009-07-01

    Mining activities are carried out by the older man and have provided resources, since ancient times, for their development and progress. With the discovery of fire will show the first metals that have marked the civilizations of copper, bronze and iron, and is the prehistory of the Stone Age tools that man has made from the exploitation of quarries first. The industrial revolution of the nineteenth century is linked to coal and steel, and could not conceiver of todays society without oil and gas, without silicon and coltan. But the mines are often aggressive and, despite their need and what they contribute to the development are answered by the societies where are made. during recent years there has been growing international efforts to try to make the minimum requirements of sustainable exploitation (European Directives, GMI, GRI, etc.) In AENOR, and within the Technical Committee of Standardization 22 Mining and Explosives, chaired by AITEMIN, was established the subcommittee 3, chaired by IGME, where, with the participation of all stake holders, have developed some standards on sustainable mining management sustainable mining that will be a tool available to mining companies to demonstrate their sustainable use to Society. (Author)

  16. Shock desensitizing of solid explosive

    Energy Technology Data Exchange (ETDEWEB)

    Davis, William C [Los Alamos National Laboratory

    2010-01-01

    Solid explosive can be desensitized by a shock wave too weak to initiate it promptly, and desensitized explosive does not react although its chemical composition is almost unchanged. A strong second shock does not cause reaction until it overtakes the first shock. The first shock, if it is strong enough, accelerates very slowly at first, and then more rapidly as detonation approaches. These facts suggest that there are two competing reactions. One is the usual explosive goes to products with the release of energy, and the other is explosive goes to dead explosive with no chemical change and no energy release. The first reaction rate is very sensitive to the local state, and the second is only weakly so. At low pressure very little energy is released and the change to dead explosive dominates. At high pressure, quite the other way, most of the explosive goes to products. Numerous experiments in both the initiation and the full detonation regimes are discussed and compared in testing these ideas.

  17. Effect Of Non-metal Elements (C, N, S) As Anionic Dopants On Electronic Structure Of Tio2-Anatase By Density-Functional Theory Approach

    OpenAIRE

    Hari Sutrisno

    2016-01-01

    This article is a theoritical approach to calculate the electronic structure of undoped- and non-metal anions doped-TiO2-anatase. The objective of the research is to calculate abinitio the band structure and the density of states (DOS) of undoped-, C-, N-, and S-doped TiO2-anatase. Kohn-Sham equations are performed with the density functional theory (DFT) using the local density approximation (LDA) for exchange-correlation functional. The first-principle calculations were done using supercell...

  18. Development of opencast mines

    Energy Technology Data Exchange (ETDEWEB)

    Szebenyi, F.

    1987-01-01

    The role and works of the Central Institute for Mining Development and its legal predecessors, the Mining Research Institute and Mines Design Institute, in relation with opencast lignite mining in Hungary, are summarized. Investigations aimed at the determination of the heating technical properties of lignites are reviewed. Different lignite mines, their geological features, production possibilities and development conditions are outlined.

  19. Research of explosives in an environment of high pressure and temperature using a new test stand

    Directory of Open Access Journals (Sweden)

    Jan Drzewiecki

    2015-01-01

    Full Text Available In this article the test stand for determining the blast abilities of explosives in high pressure and temperature conditions as well as the initial results of the research are presented. Explosives are used in rock burst and methane prevention to destroy precisely defined fragments of the rock mass where energy and methane are accumulated. Using this preventive method for fracturing the structure of the rocks which accumulate the energy or coal of the methane seam very often does not bring the anticipated results. It is because of the short range of destructive action of the post-blast gases around the blast hole. Evaluation of the blast dynamics of explosives in a test chamber, i.e. in the pressure and temperature conditions comparable to those found “in situ”, will enable evaluation of their real usefulness in commonly used mining hazard preventive methods. At the same time, it will enable the development of new designs of the explosive charges used for precisely determined mining hazards. In order to test the explosives for their use in difficult environmental conditions and to determine the characteristics of their explosion, a test chamber has been built. It is equipped with a system of sensors and a high-frequency recording system of pressure and temperature during a controlled explosion of an explosive charge. The results of the research will enable the development of new technologies for rock burst and methane prevention which will significantly increase workplace health and safety level. This paper presented results constitute the initial phase of research started in the middle of 2014.

  20. A study on optimization and rehabilitation of damaged land of surface mining

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Sun Duck; Lee, Hyun Joo [Korea Institute of Geology Mining and Materials, Taejon (Korea)

    1998-12-01

    The demand of nonmetal minerals is ever increasing according to the expansion of national economy. Especially, limestone takes more than 75% of total production of nonmetal minerals, and 125 limestone mines are producing 84,740,000 tones annually 90% of which are adopting open pit mining system. However, recently, open pit mining systems are being discouraged by the stringent environmental regulations. In this research, general survey for present status and difficulties in view of operational and regulatory point of view. Considering production scale, shape of deposit, topography and quality, new mining system has been researched for minimizing environmental impacts and maximizing economical viability. Two sample mines were chosen and the model design were suggested one of which steeply inclined deposit producing 500,000 m{sup 3}/year and the other one is mildly inclines deposit producing 2,040,000 m{sup 3}/year. In case of former one, replacing stationary crusher by portable one, 14,440 cm{sup 2} of forest damage could be reduced and cost savings of 698.53 won/m{sup 3}, internal rate of return of 22.98% and pay back period of 4.3 year could be achieved respectively. On the other hand, in case of latter one, by redesign of blasting methods and hauling route, 207,192 m{sup 2} of forest damage could be reduced and cost savings of 999 won/m{sup 3}, internal rate of return of 96.2% and pay back period of 1.0 year could be achieved respectively. (author). 16 refs., 54 tabs., 35 figs.

  1. 32 CFR 234.9 - Explosives.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 2 2010-07-01 2010-07-01 false Explosives. 234.9 Section 234.9 National Defense... PENTAGON RESERVATION § 234.9 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of a...

  2. 36 CFR 1002.38 - Explosives.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Explosives. 1002.38 Section... RECREATION § 1002.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of a permit. When...

  3. 36 CFR 2.38 - Explosives.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Explosives. 2.38 Section 2.38... PROTECTION, PUBLIC USE AND RECREATION § 2.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions...

  4. 32 CFR 1903.9 - Explosives.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false Explosives. 1903.9 Section 1903.9 National... INSTALLATIONS § 1903.9 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents, ammunition or explosive materials is prohibited on any Agency installation, except as authorized by the...

  5. [Causation, prevention and treatment of dust explosion].

    Science.gov (United States)

    Dong, Maolong; Jia, Wenbin; Wang, Hongtao; Han, Fei; Li, Xiao-Qiang; Hu, Dahai

    2014-10-01

    With the development of industrial technology, dust explosion accidents have increased, causing serious losses of people's lives and property. With the development of economy, we should lay further emphasis on causation, prevention, and treatment of dust explosion. This article summarizes the background, mechanism, prevention, and treatment of dust explosion, which may provide some professional knowledge and reference for the treatment of dust explosion.

  6. Explosive welding finds uses offshore

    Energy Technology Data Exchange (ETDEWEB)

    1984-02-01

    This article discusses an explosive welding procedure for pipeline repair. Unlike fusion welding, explosive welding does not leave a brittle area behind and will stop axial or longitudinal cracking of a pipeline. The metals are joined by cold impact pressure, which actually liquifies the metal at the point of impact. In explosive welding, the force of the circular explosion drives the two metals together with such an impact that a bonded wave pattern is set up. All surface defects and oxides are pushed ahead of the collision front, resulting in a metal-to-metal seal. Two techniques are reviewed: the Exploweld method and the Norabel method. Both methods do not reduce or expand the internal diameter of the welded surface.

  7. Detonation probabilities of high explosives

    Energy Technology Data Exchange (ETDEWEB)

    Eisenhawer, S.W.; Bott, T.F.; Bement, T.R.

    1995-07-01

    The probability of a high explosive violent reaction (HEVR) following various events is an extremely important aspect of estimating accident-sequence frequency for nuclear weapons dismantlement. In this paper, we describe the development of response curves for insults to PBX 9404, a conventional high-performance explosive used in US weapons. The insults during dismantlement include drops of high explosive (HE), strikes of tools and components on HE, and abrasion of the explosive. In the case of drops, we combine available test data on HEVRs and the results of flooring certification tests to estimate the HEVR probability. For other insults, it was necessary to use expert opinion. We describe the expert solicitation process and the methods used to consolidate the responses. The HEVR probabilities obtained from both approaches are compared.

  8. Explosive Blast Neuropathology and Seizures

    Directory of Open Access Journals (Sweden)

    S. Krisztian eKovacs

    2014-04-01

    Full Text Available Traumatic brain injury (TBI due to explosive blast exposure is a leading combat casualty. It is also implicated as a key contributor to war related mental health diseases. A clinically important consequence of all types of TBI is a high risk for development of seizures and epilepsy. Seizures have been reported in patients who have suffered blast injuries in the Global War on Terror but the exact prevalence is unknown. The occurrence of seizures supports the contention that explosive blast leads to both cellular and structural brain pathology. Unfortunately, the exact mechanism by which explosions cause brain injury is unclear, which complicates development of meaningful therapies and mitigation strategies. To help improve understanding, detailed neuropathological analysis is needed. For this, histopathological techniques are extremely valuable and indispensable. In the following we will review the pathological results, including those from immunohistochemical and special staining approaches, from recent preclinical explosive blast studies.

  9. Suppression of stratified explosive interactions

    Energy Technology Data Exchange (ETDEWEB)

    Meeks, M.K.; Shamoun, B.I.; Bonazza, R.; Corradini, M.L. [Wisconsin Univ., Madison, WI (United States). Dept. of Nuclear Engineering and Engineering Physics

    1998-01-01

    Stratified Fuel-Coolant Interaction (FCI) experiments with Refrigerant-134a and water were performed in a large-scale system. Air was uniformly injected into the coolant pool to establish a pre-existing void which could suppress the explosion. Two competing effects due to the variation of the air flow rate seem to influence the intensity of the explosion in this geometrical configuration. At low flow rates, although the injected air increases the void fraction, the concurrent agitation and mixing increases the intensity of the interaction. At higher flow rates, the increase in void fraction tends to attenuate the propagated pressure wave generated by the explosion. Experimental results show a complete suppression of the vapor explosion at high rates of air injection, corresponding to an average void fraction of larger than 30%. (author)

  10. Simulation Analysis of Indoor Gas Explosion Damage

    Institute of Scientific and Technical Information of China (English)

    钱新明; 陈林顺; 冯长根

    2003-01-01

    The influence factors and process of indoor gas explosion are studied with AutoReaGas explosion simulator. The result shows that venting pressure has great influence on the indoor gas explosion damage. The higher the venting pressure is, the more serious the hazard consequence will be. The ignition location has also evident effect on the gas explosion damage. The explosion static overpressure would not cause major injury to person and serious damage to structure in the case of low venting pressure (lower than 2 kPa). The high temperature combustion after the explosion is the major factor to person injury in indoor gas explosion accidents.

  11. Furball Explosive Breakout Test

    Energy Technology Data Exchange (ETDEWEB)

    Carroll, Joshua David [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-08-05

    For more than 30 years the Onionskin test has been the primary way to study the surface breakout of a detonation wave. Currently the Onionskin test allows for only a small, one dimensional, slice of the explosive in question to be observed. Asymmetrical features are not observable with the Onionskin test and its one dimensional view. As a result, in 2011, preliminary designs for the Hairball and Furball were developed then tested. The Hairball used shorting pins connected to an oscilloscope to determine the arrival time at 24 discrete points. This limited number of data points, caused by the limited number of oscilloscope channels, ultimately led to the Hairball’s demise. Following this, the Furball was developed to increase the number of data points collected. Instead of shorting pins the Furball uses fiber optics imaged by a streak camera to determine the detonation wave arrival time for each point. The original design was able to capture the detonation wave’s arrival time at 205 discrete points with the ability to increase the number of data points if necessary.

  12. Disaster management following explosion.

    Science.gov (United States)

    Sharma, B R

    2008-01-01

    Explosions and bombings remain the most common deliberate cause of disasters involving large numbers of casualties, especially as instruments of terrorism. These attacks are virtually always directed against the untrained and unsuspecting civilian population. Unlike the military, civilians are poorly equipped or prepared to handle the severe emotional, logistical, and medical burdens of a sudden large casualty load, and thus are completely vulnerable to terrorist aims. To address the problem to the maximum benefit of mass disaster victims, we must develop collective forethought and a broad-based consensus on triage and these decisions must reach beyond the hospital emergency department. It needs to be realized that physicians should never be placed in a position of individually deciding to deny treatment to patients without the guidance of a policy or protocol. Emergency physicians, however, may easily find themselves in a situation in which the demand for resources clearly exceeds supply and for this reason, emergency care providers, personnel, hospital administrators, religious leaders, and medical ethics committees need to engage in bioethical decision-making.

  13. Coal Mine Permit Boundaries

    Data.gov (United States)

    Earth Data Analysis Center, University of New Mexico — ESRI ArcView shapefile depicting New Mexico coal mines permitted under the Surface Mining Control and Reclamation Act of 1977 (SMCRA), by either the NM Mining these...

  14. Exploration and Mining Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2002-09-01

    This Exploration and Mining Technology Roadmap represents the third roadmap for the Mining Industry of the Future. It is based upon the results of the Exploration and Mining Roadmap Workshop held May 10 ñ 11, 2001.

  15. Numerical simulation of gas explosions

    Energy Technology Data Exchange (ETDEWEB)

    Van den Berg, A.C.; Van Wingerden, J.M.; Verhagen, T.L.

    1989-08-01

    Recent developments in numerical fluid dynamics and computer technology enable detailed simulation of gas explosions. Prins Maurits Laboratory TNO of the Netherlands Organization for Applied Scientific Research developed the necessary software. This software is a useful tool to develop and evaluate explosion safe installations. One of the possible applications is the design of save offshore rigs. (f.i. to prevent Piper Alpha disasters). The two-dimensional blast model is described and an example is given. 4 figs., 6 refs.

  16. System for analysis of explosives

    Science.gov (United States)

    Haas, Jeffrey S [San Ramon, CA

    2010-06-29

    A system for analysis of explosives. Samples are spotted on a thin layer chromatography plate. Multi-component explosives standards are spotted on the thin layer chromatography plate. The thin layer chromatography plate is dipped in a solvent mixture and chromatography is allowed to proceed. The thin layer chromatography plate is dipped in reagent 1. The thin layer chromatography plate is heated. The thin layer chromatography plate is dipped in reagent 2.

  17. Lidar Detection of Explosives Traces

    Directory of Open Access Journals (Sweden)

    Bobrovnikov Sergei M.

    2016-01-01

    Full Text Available The possibility of remote detection of traces of explosives using laser fragmentation/laser-induced fluorescence (LF/LIF is studied. Experimental data on the remote visualization of traces of trinitrotoluene (TNT, hexogen (RDX, trotyl-hexogen (Comp B, octogen (HMX, and tetryl with a scanning lidar detector of traces of nitrogen-containing explosives at a distance of 5 m are presented.

  18. Intraperitoneal explosion following gastric perforation.

    Science.gov (United States)

    Mansfield, Scott K; Borrowdale, Roderick

    2014-04-01

    The object of this study is to report a rare case of explosion during laparotomy where diathermy ignited intraperitoneal gas from a spontaneous stomach perforation. Fortunately, the patient survived but the surgeon experienced a finger burn. A literature review demonstrates other examples of intraoperative explosion where gastrointestinal gases were the fuel source. Lessons learned from these cases provide recommendations to prevent this potentially lethal event from occurring.

  19. Damage Characteristics of Surrounding Rock Subjected to VCR Mining Blasting Shock

    Directory of Open Access Journals (Sweden)

    Nan Jiang

    2015-01-01

    Full Text Available For limiting the damage range caused by explosive shock loads in vertical crater retreat (VCR mining, the blasting damage characteristics of surrounding rock were studied by two methods: numerical simulation and ultrasonic testing. Combined with the mining blasting in Dongguashan Copper Mine of China, the VCR blasting shock characteristics under different conditions are obtained by using LSDYNA. Based on statistical fracture mechanics and damage mechanics theories, a damage constitutive model for rock mass subjected to blasting shock load was established. Then by using the fast Lagrange analysis codes (FLAC3D, the blasting damage characteristics of surrounding rock were analyzed by applying the blasting shock loads obtained from the VCR mining and the damage zone is obtained. At last, the relationship between the amount of explosives and the radius of damaged surrounding rock mass was discussed, and its formula was also derived. The research provides a theoretical basis for rationally controlling stope boundaries and optimizing mining blasting parameters.

  20. In situ photo sonosynthesis and characterize nonmetal/metal dual doped honeycomb-like ZnO nanocomposites on wool fabric.

    Science.gov (United States)

    Behzadnia, Amir; Montazer, Majid; Rad, Mahnaz Mahmoudi

    2015-11-01

    In this work, nonmetal/metal dual-doped honeycomb-like N-Ag/ZnO nanocomposites were successfully photo sonosynthesized and sonoimmobilized on wool fabric through a facile one-step method under ambient pressure at low temperature as a novel photo-catalyst nanocomposite on textile material. Introducing nitrogen and silver on the sonoprepared nano ZnO particles led to superior photocatalytic activity. The homogenous distribution of the honeycomb-like nanocomposites on the fiber surface was confirmed by FE-SEM, EDX and X-ray mapping. X-ray diffraction patterns also proved the presence of silver metal with a crystal size of 54Å on the photo sonotreated sample with nonmetal/metal dual-doped honeycomb-like N-Ag/ZnO nanocomposites. The defect analysis based on XPS confirmed the composition of the nanocomposite. Ultraviolet-blocking was examined through reflectance spectra in the range of 200-800 nm showing reasonable transmittance property. The sonoloaded wool sample indicated excellent antibacterial/antifungal properties with low negative effect on human dermal fibroblasts. The role of both zinc acetate and silver nitrate concentration on diverse properties of the fabric was investigated and the optimized conditions introduced using response surface methodology. Finally a superior quality wool fabric with multifunctional properties was introduced for using special clothing in different environment.

  1. Study on the addition of nonmetal interstitial atoms to the yttrium lattice: formation of YB{sub x}, YC{sub x} and YN{sub x} alloys

    Energy Technology Data Exchange (ETDEWEB)

    Soto, Gerardo; Moreno-Armenta, Maria G.; Reyes-Serrato, Armando [Universidad Nacional Autonoma de Mexico (Mexico)

    2009-01-15

    Yttrium is a rather rare and reactive metal. Due to these characteristics it absorbs important quantities of light atoms in its void spaces. Here, we present a study where B, C and N atoms are gradually incorporated into the octahedral interstices of Y. The idea is to model, by first-principles calculations in a supercell approach, several stages of nonmetal assimilation in the yttrium lattice. In this case to develop YB{sub x}, YC{sub x} and YN{sub x} alloys. This study is limited to the cubic close-packed stacking of Y and chemical compositions in the 0{<=}x{<=}1 range. We found that the studied alloys become thermodynamically favored. The cohesive energies improve with the addition of the nonmetal atoms. Besides, the cell volume and the bulk modulus vary differently for each kind of added atom. We come upon the fact that the ratio between cohesive energy and cell volume is strikingly better for YN{sub x}. We conclude that these alloys permit a remarkable degree of modulation in their properties and electronic structures by means of chemical composition. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  2. Mining industry and US government cooperative research: Lessons learned and benefits to mining industry

    Energy Technology Data Exchange (ETDEWEB)

    Pearson, D.C.; Stump, B.W.; Phillips, W.S. [Los Alamos National Lab., NM (United States). Earth and Environmental Sciences Div.; Martin, R. [Thunder Basin Coal Co. (United States); Anderson, D.P. [Southern Methodist Univ., Dallas, TX (United States). Dept. of Geological Sciences

    1997-09-01

    Since 1994, various mines in the US have cooperated with research scientists at the Los Alamos and Lawrence Livermore National Laboratories to address issues related to verification of the Comprehensive Test Ban Treaty (CTBT). The CTBT requires that no country may conduct any nuclear explosion in the future. While the CTBT is a significant step toward reducing the global nuclear danger, verifying compliance with the treat requires that the monitoring system be able to detect, locate and identify much larger numbers of smaller amplitude seismic events than had been required previously. Large mining blasts conducted world-wide will be of sufficient amplitude to trigger the monitoring system at the lower threshold. It is therefore imperative that research into the range various blasting practices employed, the relationship of yield to seismic magnitude, and identification of anomalous blasting results be performed. This paper will describe a suite of experiments funded by the Department of Energy and conducted by the Los Alamos and Lawrence Livermore National Laboratories in cooperation with the US mining industry. Observations of cast blasting, underground long wall generated coal bumps, stoping, and explosively induced collapse of room and pillar panels will be presented. Results of these dual use experiments which are of interest to the mining community will be discussed. These include (1) variation of amplitude of seismic energy at various azimuths from cast blasts, (2) identification of the extent of back failure following explosive removal of pillars, and (3) the use of single fired shots for calibration of the monitoring system. The wealth of information and discovery described in this paper is a direct result of mutual cooperation between the US Government and the US Mining Industry.

  3. Mining review

    Science.gov (United States)

    McCartan, L.; Morse, D.E.; Plunkert, P.A.; Sibley, S.F.

    2004-01-01

    The average annual growth rate of real gross domestic product (GDP) from the third quarter of 2001 through the second quarter of 2003 in the United States was about 2.6 percent. GDP growth rates in the third and fourth quarters of 2003 were about 8 percent and 4 percent, respectively. The upward trends in many sectors of the U.S. economy in 2003, however, were shared by few of the mineral materials industries. Annual output declined in most nonfuel mining and mineral processing industries, although there was an upward turn toward yearend as prices began to increase.

  4. Coal Mines, Abandoned - Digitized Mined Areas

    Data.gov (United States)

    NSGIC GIS Inventory (aka Ramona) — Coal mining has occurred in Pennsylvania for over a century. The maps to these coal mines are stored at many various public and private locations (if they still...

  5. Wikipedia Mining

    Science.gov (United States)

    Nakayama, Kotaro; Ito, Masahiro; Erdmann, Maike; Shirakawa, Masumi; Michishita, Tomoyuki; Hara, Takahiro; Nishio, Shojiro

    Wikipedia, a collaborative Wiki-based encyclopedia, has become a huge phenomenon among Internet users. It covers a huge number of concepts of various fields such as arts, geography, history, science, sports and games. As a corpus for knowledge extraction, Wikipedia's impressive characteristics are not limited to the scale, but also include the dense link structure, URL based word sense disambiguation, and brief anchor texts. Because of these characteristics, Wikipedia has become a promising corpus and a new frontier for research. In the past few years, a considerable number of researches have been conducted in various areas such as semantic relatedness measurement, bilingual dictionary construction, and ontology construction. Extracting machine understandable knowledge from Wikipedia to enhance the intelligence on computational systems is the main goal of "Wikipedia Mining," a project on CREP (Challenge for Realizing Early Profits) in JSAI. In this paper, we take a comprehensive, panoramic view of Wikipedia Mining research and the current status of our challenge. After that, we will discuss about the future vision of this challenge.

  6. Molecular Outflows: Explosive versus Protostellar

    Science.gov (United States)

    Zapata, Luis A.; Schmid-Burgk, Johannes; Rodríguez, Luis F.; Palau, Aina; Loinard, Laurent

    2017-02-01

    With the recent recognition of a second, distinctive class of molecular outflows, namely the explosive ones not directly connected to the accretion–ejection process in star formation, a juxtaposition of the morphological and kinematic properties of both classes is warranted. By applying the same method used in Zapata et al., and using 12CO(J = 2-1) archival data from the Submillimeter Array, we contrast two well-known explosive objects, Orion KL and DR21, to HH 211 and DG Tau B, two flows representative of classical low-mass protostellar outflows. At the moment, there are only two well-established cases of explosive outflows, but with the full availability of ALMA we expect that more examples will be found in the near future. The main results are the largely different spatial distributions of the explosive flows, consisting of numerous narrow straight filament-like ejections with different orientations and in almost an isotropic configuration, the redshifted with respect to the blueshifted components of the flows (maximally separated in protostellar, largely overlapping in explosive outflows), the very-well-defined Hubble flow-like increase of velocity with distance from the origin in the explosive filaments versus the mostly non-organized CO velocity field in protostellar objects, and huge inequalities in mass, momentum, and energy of the two classes, at least for the case of low-mass flows. Finally, all the molecular filaments in the explosive outflows point back to approximately a central position (i.e., the place where its “exciting source” was located), contrary to the bulk of the molecular material within the protostellar outflows.

  7. Behavior and Release of Nitrogen at Mines and Quarries in Nordic Conditions

    Science.gov (United States)

    Karlsson, Teemu; Neitola, Raisa; Jermakka, Johannes; Merta, Elina; Mroueh, Ulla-Maija

    2015-04-01

    The increased extraction of mineral resources and mining activities creates added pressure on the environmental issues and a proper water management in mining areas in Finland. Among others, nitrogen compounds released from explosives or from mining processes can have a detrimental effect on the environment. Thus, this project aimed at comprehensive understanding on the nitrogen issue in the extractive industry. The project collected essential data on nitrogen compounds present in the environments of mines and quarries, and generated better understanding of the discharge and behaviour of nitrogen compounds in mining areas. The sources and balances of explosives-originated nitrogen compounds at mines and quarries of different sizes were investigated and compared. Additionally, the focus was in 'nitrogen smudging' problem of waste rocks and the intensity, as well as evolution and chemical characteristics of their nitrogen contamination. According to the results, the total load of potential nitrogen to the environment depends on the scale and type of the activity as well as the type of explosives used. The main emission sources of nitrogen are process and dewatering waters. A lysimeter study showed that the explosives originated nitrogen content of left over stones from natural stone quarrying is relatively low and ca. half of the nitrogen is leached within the first weeks after detonation. The "nitrogen smudging" of natural stone quarrying left over stones is relatively low to begin with and enhanced by the rapid flushing by rainwater, thus the residues of explosives should not be considered to prevent the utilization of otherwise mineralogically inert waste rocks of good technical quality. The overall nitrogen management should take into account the background concentrations and sensitivity of the local ecosystem. The research project "Solution for Control of Nitrogen Discharges at Mines and Quarries, (MINIMAN)" was realized during years 2012-2014 as a cooperative

  8. 30 CFR 56.6801 - Vehicle repair.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Vehicle repair. 56.6801 Section 56.6801 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... Vehicle repair. Vehicles containing explosive material and oxidizers shall not be taken into a...

  9. 30 CFR 56.6902 - Excessive temperatures.

    Science.gov (United States)

    2010-07-01

    ... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Requirements § 56.6902 Excessive temperatures. (a) Where heat could cause premature detonation, explosive... the initiation of the blast to no more than 12 hours; and (3) Take other special precautions to...

  10. THE INFLUENCE OF BARRIERS ON FLAME AND EXPLOSION WAVE IN GAS EXPLOSION

    Institute of Scientific and Technical Information of China (English)

    林柏泉; 周世宁; 张仁贵

    1998-01-01

    This paper researches into the influence of barriers on flame and explosion wave in gasexplosion on the basis of experiment. The result shows that the barrier is very important to thetransmission of flame and explosion wave in gas explosion. When there are barriers, the speed oftransmission would be very fast and shock wave will appear in gas explosion, which would in-crease gas explosion power. The result of research is very important to prevent gas explosion anddecrease the power of it.

  11. Thermodynamic States in Explosion Fields

    Energy Technology Data Exchange (ETDEWEB)

    Kuhl, A L

    2009-10-16

    Here we investigate the thermodynamic states occurring in explosion fields from the detonation of condensed explosives in air. In typical applications, the pressure of expanded detonation products gases is modeled by a Jones-Wilkins-Lee (JWL) function: P{sub JWL} = f(v,s{sub CJ}); constants in that function are fit to cylinder test data. This function provides a specification of pressure as a function of specific volume, v, along the expansion isentrope (s = constant = s{sub CJ}) starting at the Chapman-Jouguet (CJ) state. However, the JWL function is not a fundamental equation of thermodynamics, and therefore gives an incomplete specification of states. For example, explosions inherently involve shock reflections from surfaces; this changes the entropy of the products, and in such situations the JWL function provides no information on the products states. In addition, most explosives are not oxygen balanced, so if hot detonation products mix with air, they after-burn, releasing the heat of reaction via a turbulent combustion process. This raises the temperature of explosion products cloud to the adiabatic flame temperature ({approx}3,000K). Again, the JWL function provides no information on the combustion products states.

  12. National Underground Mines Inventory

    Science.gov (United States)

    1983-10-01

    08 019 726 LONG PARK 15 0502379 08 095 2904 GEO a1 MINE 0502383 08 085 2904 BESSIE 0 MINE 0502387 08 667 2904 PAYSTREAK 0502397 08 113 2904 BUENO MILL...35 061QUESTA MINE 2901267 35 055 43560 ’ RUDY NO, I S 2 2901364 35 031 MT, TAYLOR 2901375 35 061 0 MARQUEZ SHAFT 2901597 35 031 6534 MARIANO LAKE MINE

  13. Mining ergonomics

    Energy Technology Data Exchange (ETDEWEB)

    McPhee, B.

    2007-02-15

    Changes in work practices and a drive for greater productivity have introduced a range of emerging issues in ergonomics in mining. Some of the practices appear to be at odds with the need to improve general occupational health and safety. Longer shift lengths and fatigue, mental overload and underload, intermittent heavy physical work, reduced task variation, sedentary work in fixed postures and whole-body vibration all have risks for health and safety. The increasing age of some of the workforce is of concern. There appears to be a need to recognise these as potential causes of health problems. The article gives a review of these problems are reports on research findings. 36 refs., 3 figs.

  14. Low cost mobile explosive/drug detection devices

    Science.gov (United States)

    Gozani, T.; Bendahan, J.

    1999-06-01

    Inspection technologies based on Thermal Neutron Analysis (TNA®) and/or Fast Neutron Analysis (FNA) are the basis for relatively compact and low-cost, material-sensitive devices for a wide variety of inspection needs. The TNA allows the use of either isotropic neutron sources such as a 252Cf, or electronic neutron generators such as the d-T sealed neutron generator tubes. The latter could be used in a steady state mode or in slow (>μs) pulsing mode, to separate the thermal neutron capture signatures following the pulse from the combination of the FNA plus TNA signatures during the pulse. Over the years, Ancore Corporation has built and is continuing to develop a variety of inspection devices based on its TNA and FNA technologies: SPEDS—an explosive detection device for small parcels, portable electronics, briefcases and other similar carry-on items; MDS—a system for the detection or confirmation of buried mines; VEDS—a system for the detection of varied amounts of explosives and/or drugs concealed in passenger vehicles, pallets, lightly loaded trucks or containers, etc.; ACD—a device to clear alarms from a primary, non-specific explosive detection system for passenger luggage. The principle and performance of these devices will be shown and discussed.

  15. The Quiet Explosion

    Science.gov (United States)

    2008-07-01

    A European-led team of astronomers are providing hints that a recent supernova may not be as normal as initially thought. Instead, the star that exploded is now understood to have collapsed into a black hole, producing a weak jet, typical of much more violent events, the so-called gamma-ray bursts. The object, SN 2008D, is thus probably among the weakest explosions that produce very fast moving jets. This discovery represents a crucial milestone in the understanding of the most violent phenomena observed in the Universe. Black Hole ESO PR Photo 23a/08 A Galaxy and two Supernovae These striking results, partly based on observations with ESO's Very Large Telescope, will appear tomorrow in Science Express, the online version of Science. Stars that were at birth more massive than about 8 times the mass of our Sun end their relatively short life in a cosmic, cataclysmic firework lighting up the Universe. The outcome is the formation of the densest objects that exist, neutron stars and black holes. When exploding, some of the most massive stars emit a short cry of agony, in the form of a burst of very energetic light, X- or gamma-rays. In the early afternoon (in Europe) of 9 January 2008, the NASA/STFC/ASI Swift telescope discovered serendipitously a 5-minute long burst of X-rays coming from within the spiral galaxy NGC 2770, located 90 million light-years away towards the Lynx constellation. The Swift satellite was studying a supernova that had exploded the previous year in the same galaxy, but the burst of X-rays came from another location, and was soon shown to arise from a different supernova, named SN 2008D. Researchers at the Italian National Institute for Astrophysics (INAF), the Max-Planck Institute for Astrophysics (MPA), ESO, and at various other institutions have observed the supernova at great length. The team is led by Paolo Mazzali of INAF's Padova Observatory and MPA. "What made this event very interesting," says Mazzali, "is that the X-ray signal was very

  16. Mining lore : Bankhead, mining for coal

    Energy Technology Data Exchange (ETDEWEB)

    Nichiporuk, A.

    2007-09-15

    Bankhead, Alberta was one of the first communities to be established because of mining. It was founded in 1903 by the Canadian Pacific Railway (CPR) on Cascade Mountain in the Bow River Valley of Banff National Park. In 1904, Mine No. 80 was opened by the Pacific Coal Company to fuel CPR's steam engines. In order to avoid flooding the mine, the decision was made to mine up the steep seams instead of down. The mine entered full production in 1905. This article described the working conditions and pay scale for the mine workers, noting that there was not much in terms of safety equipment. There were many accidents and 15 men lost their lives at the mine. During the mine's 20-year operation, miners went on strike 6 times. The last strike marked the closure of the mine in June 1922 and the end of industry in national parks. CPR was ordered to clear out and move the mining equipment as well as the houses, buildings and essentially the entire town. During its peak production, Mine No. 80 produced about a half million tons of coal. 1 ref., 1 fig.

  17. Optimal dynamic detection of explosives

    Energy Technology Data Exchange (ETDEWEB)

    Moore, David Steven [Los Alamos National Laboratory; Mcgrane, Shawn D [Los Alamos National Laboratory; Greenfield, Margo T [Los Alamos National Laboratory; Scharff, R J [Los Alamos National Laboratory; Rabitz, Herschel A [PRINCETON UNIV; Roslund, J [PRINCETON UNIV

    2009-01-01

    The detection of explosives is a notoriously difficult problem, especially at stand-off distances, due to their (generally) low vapor pressure, environmental and matrix interferences, and packaging. We are exploring optimal dynamic detection to exploit the best capabilities of recent advances in laser technology and recent discoveries in optimal shaping of laser pulses for control of molecular processes to significantly enhance the standoff detection of explosives. The core of the ODD-Ex technique is the introduction of optimally shaped laser pulses to simultaneously enhance sensitivity of explosives signatures while reducing the influence of noise and the signals from background interferents in the field (increase selectivity). These goals are being addressed by operating in an optimal nonlinear fashion, typically with a single shaped laser pulse inherently containing within it coherently locked control and probe sub-pulses. With sufficient bandwidth, the technique is capable of intrinsically providing orthogonal broad spectral information for data fusion, all from a single optimal pulse.

  18. Coulomb explosion of "hot spot"

    CERN Document Server

    Oreshkin, V I; Chaikovsky, S A; Artyomov, A P

    2016-01-01

    The study presented in this paper has shown that the generation of hard x rays and high-energy ions, which are detected in pinch implosion experiments, may be associated with the Coulomb explosion of the hot spot that is formed due to the outflow of the material from the pinch cross point. During the process of material outflow, the temperature of the hot spot plasma increases, and conditions arise for the plasma electrons to become continuously accelerated. The runaway of electrons from the hot spot region results in the buildup of positive space charge in this region followed by a Coulomb explosion. The conditions for the hot spot plasma electrons to become continuously accelerated have been revealed and estimates have been obtained for the kinetic energy of the ions generated by the Coulomb explosion.

  19. Evidence for Nearby Supernova Explosions

    CERN Document Server

    Benítez, N; Canelles, M; Benitez, Narciso; Maiz-Apellaniz, Jesus; Canelles, Matilde

    2002-01-01

    Supernova explosions are one of the most energetic--and potentially lethal--phenomena in the Universe. Scientists have speculated for decades about the possible consequences for life on Earth of a nearby supernova, but plausible candidates for such an event were lacking. Here we show that the Scorpius-Centaurus OB association, a group of young stars currently located at~130 parsecs from the Sun, has generated 20 SN explosions during the last 11 Myr, some of them probably as close as 40 pc to our planet. We find that the deposition on Earth of 60Fe atoms produced by these explosions can explain the recent measurements of an excess of this isotope in deep ocean crust samples. We propose that ~2 Myr ago, one of the SNe exploded close enough to Earth to seriously damage the ozone layer, provoking or contributing to the Pliocene-Pleistocene boundary marine extinction.

  20. Tube bundle system: for monitoring of coal mine atmosphere.

    Science.gov (United States)

    Zipf, R Karl; Marchewka, W; Mohamed, K; Addis, J; Karnack, F

    2013-05-01

    A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fire or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. Most longwall coal mines in Australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflow monitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

  1. Effect of Electronegativity and Charge Balance on the Visible-Light-Responsive Photocatalytic Activity of Nonmetal Doped Anatase TiO2

    Directory of Open Access Journals (Sweden)

    Jibao Lu

    2012-01-01

    Full Text Available The origin of visible light absorption and photocatalytic activity of nonmetal doped anatase TiO2 were investigated in details in this work based on density functional theory calculations. Our results indicate that the electronegativity is of great significance in the band structures, which determines the relative positions of impurity states induced by the doping species, and further influences the optical absorption and photocatalytic activities of doped TiO2. The effect of charge balance on the electronic structure was also discussed, and it was found that the charge-balance structures may be more efficient for visible light photocatalytic activities. In addition, the edge positions of conduction band and valence band, which determine the ability of a semiconductor to transfer photoexcited electrons to species adsorbed on its surface, were predicted as well. The results may provide a reference to further experimental studies.

  2. Adsorption of alkali, alkaline-earth, simple and 3d transition metal, and nonmetal atoms on monolayer MoS2

    Directory of Open Access Journals (Sweden)

    X. D. Li

    2015-05-01

    Full Text Available Single adsorption of different atoms on pristine two-dimensional monolayer MoS2 have been systematically investigated by using density functional calculations with van der Waals correction. The adatoms cover alkali metals, alkaline earth metals, main group metal, 3d-transition metals, coinage metal and nonmetal atoms. Depending on the adatom type, metallic, semimetallic or semiconducting behavior can be found in direct bandgap monolayer MoS2. Additionally, local or long-range magnetic moments of two-dimensional MoS2 sheet can also attained through the adsorption. The detailed atomic-scale knowledge of single adsorption on MoS2 monolayer is important not only for the sake of a theoretical understanding, but also device level deposition technological application.

  3. Local-moment formation and metal–nonmetal transition in Ca1-YVO3 and Ca1-YTiO3

    Indian Academy of Sciences (India)

    Y Nishihara; H Kawanaka; H Bando

    2002-05-01

    Electron-doped metallic states of Ca1-YVO3 and Ca1-YTiO3 change into nonmetallic states around ∼ 0.4 and 0.6, respectively. The residual resistivity in the metallic states increases with increasing effective magnetic moment or coefficient of 2 term of resistivity. The effective moment reaches ∼ 0.5 B/molecule in Ca1-YVO3 and also in Ca1-YTiO3 near the metal–nonmetal phase boundary. In these metallic states, ∼ 10% of 3 atoms seem to have large localized magnetic moments. In electron-doped metallic sample of Ca1-YVO3, the temperature dependence of resistance shows no resistance-minimum. However, weak negative magneto-resistance is observed for the sample with = 0.2 up to 50 Tesla at 4.2 K.

  4. Mining and environment

    Energy Technology Data Exchange (ETDEWEB)

    Kisgyorgy, S.

    1986-01-01

    The realization of new mining projects should be preceded by detailed studies on the impact of mining activities on the environment. For defining the conditions of environmental protection and for making proper financial plans the preparation of an information system is needed. The possible social effects of the mining investments have to be estimated, first of all from the points of view of waste disposal, mining hydrology, subsidence due to underground mining etc.

  5. Explosively Joining Dissimilar Metal Tubes.

    Science.gov (United States)

    1979-11-01

    both steel, photograph (7), and the Ni-Cu specimen, photograph (8) , showed considerable pitting corrosion in the aluminum . 4. The paint was then...for 6061 -T6 aluminum and are: collision angle 5 - 200, collision velocity 270 - 350 m/sec, with an impact pressure of at least 27 Kbar (391 Kpsi...Welded Aluminum Alloy 1 .. 5 rn-i (P0 -I Op. 2si 11 6W TABLE I Explosive2 Cladder Metal Base Metal Explosive Loading (gins/in2 6061 -T6 Al 304 SS TSE- 1004

  6. Intravesical explosion during transurethral electrosurgery.

    Science.gov (United States)

    Georgios, Kallinikas; Evangelos, Boulinakis; Helai, Habib; Ioannis, Gerzelis

    2015-05-01

    Intravesical explosion is a very rare complication of transurethral resection of prostate and transurethral resection of bladder tumour operations. In vitro studies have shown that the gases produced during the procedure could result in a blast once they are mixed with air from the atmosphere. A 79-year-old male experienced an explosion in his bladder while undergoing a transurethral resection of bladder tumour. The case is presented as well as the way that it was treated as an emergency. Precautions of such events are finally suggested.

  7. Imaging of metals, metalloids, and non-metals by laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) in biological tissues.

    Science.gov (United States)

    Becker, J Sabine; Becker, J Susanne

    2010-01-01

    The determination of the localization and distribution of essential and beneficial metals (e.g., Cu, Fe, Zn, Mn, Co, Ti, Al, Ca, K, Na, Cr and others), toxic metals (like Cd, Pb, Hg, U), metalloids (e.g., As, Se, Sb), and non-metals (such as C, S, P, Cl, I) in biological tissues is a challenging task for life science studies. Over the past few years, the development and application of mass spectrometric imaging (MSI) techniques for elements has been rapidly growing in the life sciences in order to investigate the uptake and the transport of both essential and toxic metals in plant and animal sections. Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) is a very sensitive and efficient trace, surface, and isotopic analytical technique for biological samples. LA-ICP-MS is increasingly utilized as an elemental mass spectrometric technique using double-focusing sector field (LA-ICP-SFMS) or quadrupole mass spectrometers (LA-ICP-QMS) to produce images of detailed regionally specific element distributions in thin biological tissue sections. Nowadays, MSI studies focus on brain research for studying neurodegenerative diseases such as Alzheimer's or Parkinson's, stroke, or tumor growth, or for the imaging of cancer biomarkers in tissue sections.The combination of the mass spectrometry imaging of metals by LA-ICP-MS with proteomics using biomolecular mass spectrometry (such as MALDI-MS or ESI-MS) to identify metal-containing proteins has become an important strategy in the life sciences. Besides the quantitative imaging of metals, non-metals and metalloids in biological tissues, LA-ICP-MS has been utilized for imaging metal-containing proteins in a 2D gel after electrophoretic separation of proteins. Recent progress in applying LA-ICP-MS in life science studies will be reviewed including the imaging of thin slices of biological tissue and applications in proteome analysis in combination with MALDI/ESI-MS to analyze metal-containing proteins.

  8. Abnormality of the corpus callosum in coalmine gas explosion-related posttraumatic stress disorder.

    Science.gov (United States)

    Zhang, Yang; Li, Huabing; Lang, Xu; Zhuo, Chuanjun; Qin, Wen; Zhang, Quan

    2015-01-01

    Abnormal corpus callosum (CC) has been reported in childhood trauma-related posttraumatic stress disorder (PTSD); however, the nature of white matter (WM) integrity alterations in the CC of young adult-onset PTSD patients is unknown. In this study, 14 victims of a coal mine gas explosion with PTSD and 23 matched coal miners without experiencing the coal mine explosion were enrolled. The differences in fractional anisotropy (FA) within 7 sub-regions of the CC were compared between the two groups. Compared to the controls, PTSD coal miners exhibited significantly reduced FA values in the anterior sub-regions of the CC (P < 0.05, Bonferroni-corrected), which mainly interconnect the bilateral frontal cortices. Our findings indicated that the anterior part of the CC was more severely impaired than the posterior part in young adult-onset PTSD, which suggested the patterns of CC impairment may depend on the developmental stage of the structure when the PTSD occurs.

  9. 46 CFR 188.10-25 - Explosive.

    Science.gov (United States)

    2010-10-01

    ... mixture, the primary purpose of which is to function by explosion; i.e., with substantially instantaneous release of gas and heat. Explosives are discussed in more detail in 49 CFR parts 171-179....

  10. New Source Model for Chemical Explosions

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Xiaoning [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-03-03

    With sophisticated inversion scheme, we recover characteristics of SPE explosions such as corner frequency fc and moment M0, which are used to develop a new source model for chemical explosions.

  11. Pulmonary contusion and hemothorax due to explosion

    National Research Council Canada - National Science Library

    Baeza-Herrera, Carlos; Sanjuán-Fabián, Héctor; Medellín-Sierra, Ulises Darío; Nájera-Garduño, Heladio; García-Cabello, Luis Manuel

    2006-01-01

    .... Such is the case of gunpowder explosive objects used during celebration holidays. We present a 14-year-old male who suffered a pulmonary contusion as a consequence of an explosion of "huevo de codorniz...

  12. Structures and Opportunities to Supply the Telecommunication Systems in Underground Mines

    Science.gov (United States)

    Wojaczek, Antoni

    2016-06-01

    Telecommunication systems in underground mines require reliable power supply both of stationary and underground devices. Special problems connected with power supply occur in a case when subscriber devices are located in explosion hazard areas. The paper presents the basic problems connected with power supply of stationary elements of safety systems as well as subscriber devices located in explosion hazard areas that are significantly distant from stationary elements. Acceptable methods of supplying the subscribers devices under technical environment conditions of mine undergrounds have been determined.

  13. The behavior limestone under explosive load

    Science.gov (United States)

    Orlov, M. Yu; Orlova, Yu N.; Bogomolov, G. N.

    2016-11-01

    Limestone behavior under explosive loading was investigated. The behavior of the limestone by the action of the three types of explosives, including granular, ammonite and emulsion explosives was studied in detail. The shape and diameter of the explosion craters were obtained. The observed fragments after the blast have been classified as large, medium and small fragments. Three full-scale experiments were carried out. The research results can be used as a qualitative test for the approbation of numerical methods.

  14. Gas Explosions Mitigation by Ducted Venting

    OpenAIRE

    2007-01-01

    The mitigation of effects of gas and dust explosions within industrial equipment is effective if venting the combustion products to safe location. The presence of relief duct is however likely to increase the severity of the explosion with respect to equipment vented to open atmosphere, due to secondary explosions occurring in the initial sections of duct, frictional drag and inertia of the gas column, acoustic and Helmholtz oscillations. The weights of these phenomena on explosion e...

  15. Statistical estimation of loads from gas explosions

    OpenAIRE

    Høiset, Stian

    1998-01-01

    In the design of structures in the offshore and process industries, the possibility of a gas explosion must always be considered. This is usually incorporated by performing explosion simulations. However, estimations based on such calculations introduce uncertainties in the design process. The main uncertainties in explosion simulations are the assumption of the gas cloud,the location of the ignition point and the properties of the explosion simulator itself. In this thesis, we try to investi...

  16. 75 FR 70291 - Commerce in Explosives; List of Explosive Materials (2010R-27T)

    Science.gov (United States)

    2010-11-17

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF JUSTICE Bureau of Alcohol, Tobacco, Firearms and Explosives Commerce in Explosives; List of Explosive Materials (2010R-27T) AGENCY: Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF), Department of...

  17. 77 FR 58410 - Commerce in Explosives; List of Explosive Materials (2012R-10T)

    Science.gov (United States)

    2012-09-20

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF JUSTICE Bureau of Alcohol, Tobacco, Firearms, and Explosives Commerce in Explosives; List of Explosive Materials (2012R-10T) AGENCY: Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF), Department of...

  18. 76 FR 64974 - Commerce in Explosives; List of Explosive Materials (2011R-18T)

    Science.gov (United States)

    2011-10-19

    ... From the Federal Register Online via the Government Publishing Office ] DEPARTMENT OF JUSTICE Bureau of Alcohol, Tobacco, Firearms and Explosives Commerce in Explosives; List of Explosive Materials (2011R-18T) AGENCY: Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF), Department of...

  19. Explosive micro-bubble actuator

    NARCIS (Netherlands)

    Broek, van den D.M.; Elwenspoek, M.

    2008-01-01

    Explosive evaporation occurs when a liquid is exposed to extremely high heat-fluxes. Within a few microseconds a bubble in the form vapour film is generated, followed by rapid growth due to the pressure impulse and finally the bubbles collapse. This effect, which already has proven its use in curren

  20. Explosive micro-bubble actuator

    NARCIS (Netherlands)

    Broek, van den D.M.; Elwenspoek, M.C.

    2007-01-01

    Explosive evaporation occurs when a thin layer of liquid reaches a very high temperature in a very short time. At these temperatures homogeneous nucleation takes place. The nucleated bubbles almost instantly coalesce forming a vapour film followed by rapid growth due to the pressure impulse and fina

  1. Measuring explosive non-ideality

    Energy Technology Data Exchange (ETDEWEB)

    Souers, P C

    1999-02-17

    The sonic reaction zone length may be measured by four methods: (1) size effect, (2) detonation front curvature, (3) crystal interface velocity and (4) in-situ gauges. The amount of data decreases exponentially from (1) to (4) with there being almost no gauge data for prompt detonation at steady state. The ease and clarity of obtaining the reaction zone length increases from (1) to (4). The method of getting the reaction zone length, , is described for the four methods. A measure of non-ideality is proposed: the reaction zone length divided by the cylinder radius. N = /R{sub o}. N = 0 for true ideality. It also decreases with increasing radius as it should. For N < 0.10, an equilibrium EOS like the JWL may be used. For N > 0.10, a time-dependent description is essential. The crystal experiment, which measures the particle velocity of an explosive-transparent material interface, is presently rising in importance. We examine the data from three experiments and apply: (1) an impedance correction that transfers the explosive C-J particle velocity to the corresponding value for the interface, and (2) multiplies the interface time by 3/4 to simulate the explosive speed of sound. The result is a reaction zone length comparable to those obtained by other means. A few explosives have reaction zones so small that the change of slope in the particle velocity is easily seen.

  2. Explosion mitigation by water mist

    NARCIS (Netherlands)

    Wal, R. van der; Cargill, S.; Longbottom, A.; Rhijnsburger, M.P.M.; Erkel, A.G. van

    2010-01-01

    The internal explosion of an anti-ship missile or stored ammunition is a potentially catastrophic threat for a navy vessel. These events generally cause heavy blast loading and fragments to perforate the ship structure. As a solution to reduce the blast loading, the compartment can be filled with

  3. Lead-free primary explosives

    Science.gov (United States)

    Huynh, My Hang V.

    2010-06-22

    Lead-free primary explosives of the formula (cat).sub.Y[M.sup.II(T).sub.X(H.sub.2O).sub.6-X].sub.Z, where T is 5-nitrotetrazolate, and syntheses thereof are described. Substantially stoichiometric equivalents of the reactants lead to high yields of pure compositions thereby avoiding dangerous purification steps.

  4. Turbulent Combustion in SDF Explosions

    Energy Technology Data Exchange (ETDEWEB)

    Kuhl, A L; Bell, J B; Beckner, V E

    2009-11-12

    A heterogeneous continuum model is proposed to describe the dispersion and combustion of an aluminum particle cloud in an explosion. It combines the gas-dynamic conservation laws for the gas phase with a continuum model for the dispersed phase, as formulated by Nigmatulin. Inter-phase mass, momentum and energy exchange are prescribed by phenomenological models. It incorporates a combustion model based on the mass conservation laws for fuel, air and products; source/sink terms are treated in the fast-chemistry limit appropriate for such gasdynamic fields, along with a model for mass transfer from the particle phase to the gas. The model takes into account both the afterburning of the detonation products of the C-4 booster with air, and the combustion of the Al particles with air. The model equations were integrated by high-order Godunov schemes for both the gas and particle phases. Numerical simulations of the explosion fields from 1.5-g Shock-Dispersed-Fuel (SDF) charge in a 6.6 liter calorimeter were used to validate the combustion model. Then the model was applied to 10-kg Al-SDF explosions in a an unconfined height-of-burst explosion. Computed pressure histories are compared with measured waveforms. Differences are caused by physical-chemical kinetic effects of particle combustion which induce ignition delays in the initial reactive blast wave and quenching of reactions at late times. Current simulations give initial insights into such modeling issues.

  5. Optical Pressure Measurements of Explosions

    Science.gov (United States)

    2013-09-01

    Explosive Shocks in Air, 2nd ed.; Springer-Verlag: Berlin , Germany, 1985. 7. Anderson, J. D. Hypersonic and High Temperature Gas Dynamics, 2nd Ed...PDF) RDRL CIO LA T LANDFRIED RDRL WML M ZOLTOSKI RDRL WML A F DE LUCIA W OBERLE RDRL WML B J GOTTFRIED J CIEZAK

  6. MECHANISM OF EXPLOSIVE WELDING OF METALS

    OpenAIRE

    Sek, W.

    1988-01-01

    Mechanism of explosive welding is discussed. The experimental date indicate that the explosive bonding interface forms behind the collision point and the physical properties of metals affect considerably this process. The usefulness of hydrodynamic model for describing the explosive welding process is called in question.

  7. 14 CFR 420.63 - Explosive siting.

    Science.gov (United States)

    2010-01-01

    ... Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION, FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... site plan shall include: (1) A scaled map that shows the location of all proposed explosive hazard... explosive hazard facility and all other explosive hazard facilities and each public area, including...

  8. 30 CFR 77.1301 - Explosives; magazines.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosives; magazines. 77.1301 Section 77.1301... and Blasting § 77.1301 Explosives; magazines. (a) Detonators and explosives other than blasting agents shall be stored in magazines. (b) Detonators shall not be stored in the same magazine with...

  9. 49 CFR 173.54 - Forbidden explosives.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Forbidden explosives. 173.54 Section 173.54... SHIPMENTS AND PACKAGINGS Definitions, Classification and Packaging for Class 1 § 173.54 Forbidden explosives. Unless otherwise provided in this subchapter, the following explosives shall not be offered for...

  10. 46 CFR 147.95 - Explosives.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Explosives. 147.95 Section 147.95 Shipping COAST GUARD... Special Requirements for Particular Materials § 147.95 Explosives. (a) Explosives—general. Except as provided for elsewhere in this subchapter, explosives, as defined in 49 CFR 173.50, which are hazardous...

  11. 46 CFR 153.921 - Explosives.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Explosives. 153.921 Section 153.921 Shipping COAST GUARD....921 Explosives. No person may load, off-load, or carry a cargo listed in this part on board a vessel that carries explosives unless he has the prior written permission of the Commandant (CG-522). ...

  12. Portable SERS Instrument for Explosives Monitoring

    Science.gov (United States)

    2008-01-01

    groundwater monitoring from a cone penetrometer (CPT) platform (5) Demonstrate improved capability for discriminating explosives versus colorimetry ...interference, and better discrimination of individual explosives compared to colorimetry • Applicability to virtually any environmental water...chemicals such as nitroaromatics or nitramines. While this makes colorimetry more generally applicable at explosive sites, it also limits the ability to

  13. Scientific Support for NQR Explosive Detection Development

    Science.gov (United States)

    2006-07-01

    Final 3. DATES COVERED (From - To) 8 March 2004 - 7 March 2006 4. TITLE AND SUBTITLE Scientific Support for NQR Explosive Detection Development...Laboratory (NRL) to improve explosive detection using nuclear quadrupole resonance ( NQR ) is summarized. The work includes studies of the effects...superconducting coils for explosive detection. Additional studies involving slowly rotating NQR measurements were also pursued. 15. SUBJECT TERMS Nuclear

  14. Explosion Power and Pressure Desensitization Resisting Property of Emulsion Explosives Sensitized by MgH2

    Science.gov (United States)

    Cheng, Yangfan; Ma, Honghao; Liu, Rong; Shen, Zhaowu

    2014-07-01

    Due to low detonation power and pressure desensitization problems that traditional emulsion explosives encounter in utilization, a hydrogen-based emulsion explosives was devised. This type of emulsion explosives is sensitized by hydrogen-containing material MgH2, and MgH2 plays a double role as a sensitizer and an energetic material in emulsion explosives. Underwater explosion experiments and shock wave desensitization experiments show that an MgH2 emulsion explosives has excellent detonation characteristics and is resistant to pressure desensitization. The pressure desensitization-resistant mechanism of MgH2 emulsion explosives was investigated using scanning electron microscopy.

  15. Degasification possibilities evaluation in Socotá coal mines (Boyacá, Colombia

    Directory of Open Access Journals (Sweden)

    Jorge Eliécer Mariño-Martínez

    2016-09-01

    Those wells would not only produce gas, but would also degas the future underground mining areas. The combination of degasification and ventilation would considerably allow a decrease in the explosions risk. The high coalbed methane content in the area could produce energy for the mining company or commercial gas for the natural gas distribution network. The Socotá area has the ideal conditions for a pilot project, which could be a model for other degasification projects in Colombia.

  16. Gas explosions - an elementary account; Eksplosiv fare

    Energy Technology Data Exchange (ETDEWEB)

    Seehusen, Joachim

    2002-07-01

    Although in a typical gas explosion the flame front propagates at sub-sonic speed, it still moves fast. Safety people often believe they can run away from a gas explosion. While gas explosions are well understood in the major companies, this is not true in many small ones, and people often do not realise how small the difference may be between a small puff and a dangerous explosion. Of special interest in a ''hydrogen society'' is the fact that hydrogen is dangerous and must be handled with care. The article discusses in an elementary way some of the basic concepts from the physics of gas explosions.

  17. Damage Effects of Shelled Explosive Explosion in Concrete

    Directory of Open Access Journals (Sweden)

    Liu Yan

    2010-10-01

    Full Text Available The damage of concrete subjected to explosion loading is an important issue in defense engineering. The damage degree of concrete is related to many factors, such as the type of explosive charge, the depth of burial and the parameters of concrete. In this paper, three factors are considered for experiments of shelled explosives in concrete targets, which are the filling coefficient, length-to-diameter ratio and the depth of burial. The filling coefficient is from 0.1 to 1 by changing thickness of shell, and length-to-diameter ratio is from 2.5 to 10. The unconfined compressive strength of concrete target for test is 35MPa. The experimental results showed that the sizes of craters of concretes are varied as the filling coefficient, length-to-diameter ratio and the depth of burial. The optimal values of filling coefficient, length-to-diameter ratio and the depth of burial of shelled charges were obtained to get largest damage regions of concrete targets. This work provides a base for evaluating the damage of concrete and designing the penetrating warhead.Defence Science Journal, 2010, 60(6, pp.672-677, DOI:http://dx.doi.org/10.14429/dsj.60.434

  18. Neutralization of potential land mine hazards by abrasive waterjet use

    Science.gov (United States)

    Summers, David A.; Fossey, Robert D.; Thompson, S. J.

    1998-09-01

    A method of neutralizing landmines in which the integrity of the surrounding terrain is retained is herein described. High pressure waterjets which can be used to detect the presence of landmines can then be used to remove the soil and other cover in a plane immediately adjacent to and around the mine so that the side of the mine can be visually inspected through a remote television camera. At that time the flow of water is channeled through a line in which small particles of sand are added to the waterjet which is at a pressure of between 3,000 and 10,000 psi depending on the device which is used. Jet flow rates are on the order of 5 gpm depending on the nozzle configuration used. By bringing this abrasive stream in along a lateral plane through the mine it is possible to intersect, and neutralize, the fusing systems most likely to be used to initiate the charge, in a single pass. At higher flow rates, as the cut is made the jet will generate significant turbulence in the mine body, sufficient to remove a considerable quantity of the explosive which is resident within the mine at the same time as the mine is being dissected. The precision of cut achievable is shown by the longitudinal cutting into two parts of live detonators, as well as representative mine bodies.

  19. Spot test kit for explosives detection

    Science.gov (United States)

    Pagoria, Philip F; Whipple, Richard E; Nunes, Peter J; Eckels, Joel Del; Reynolds, John G; Miles, Robin R; Chiarappa-Zucca, Marina L

    2014-03-11

    An explosion tester system comprising a body, a lateral flow membrane swab unit adapted to be removeably connected to the body, a first explosives detecting reagent, a first reagent holder and dispenser operatively connected to the body, the first reagent holder and dispenser containing the first explosives detecting reagent and positioned to deliver the first explosives detecting reagent to the lateral flow membrane swab unit when the lateral flow membrane swab unit is connected to the body, a second explosives detecting reagent, and a second reagent holder and dispenser operatively connected to the body, the second reagent holder and dispenser containing the second explosives detecting reagent and positioned to deliver the second explosives detecting reagent to the lateral flow membrane swab unit when the lateral flow membrane swab unit is connected to the body.

  20. Sensitivity to friction for primary explosives.

    Science.gov (United States)

    Matyáš, Robert; Šelešovský, Jakub; Musil, Tomáš

    2012-04-30

    The sensitivity to friction for a selection of primary explosives has been studied using a small BAM friction apparatus. The probit analysis was used for the construction of a sensitivity curve for each primary explosive tested. Two groups of primary explosives were chosen for measurement (a) the most commonly used industrially produced primary explosives (e.g. lead azide, tetrazene, dinol, lead styphnate) and (b) the most produced improvised primary explosives (e.g. triacetone triperoxide, hexamethylenetriperoxide diamine, mercury fulminate, acetylides of heavy metals). A knowledge of friction sensitivity is very important for determining manipulation safety for primary explosives. All the primary explosives tested were carefully characterised (synthesis procedure, shape and size of crystals). The sensitivity curves obtained represent a unique set of data, which cannot be found anywhere else in the available literature. Copyright © 2012 Elsevier B.V. All rights reserved.

  1. First Mexican coal mine recovery after mine fire, Esmeralda Mine

    Energy Technology Data Exchange (ETDEWEB)

    Santillan, M.A. [Minerales Monclova, SA de CV, Palau Coahuila (Mexico)

    2005-07-01

    The fire started on 8 May 1998 in the development section from methane released into the mine through a roof-bolt hole. The flames spread quickly as the coal was ignited. After eight hours the Safety Department decided to seal the vertical ventilation shafts and the slopes. The quality of coal in the Esmeralda Mine is very high quality, and Minerales Monclova (MIMOSA) decided to recover the facilities. However, the Esmeralda Mine coals have a very high gas content of 12 m{sup 3}/t. During the next 2.5 months, MIMOSA staff and specialists observed and analysed the gas behaviour supported by a chromatograph. With the results of the observations and analyses, MIMOSA in consultation with the specialists developed a recovery plan based on flooding the area in which fire might have propagated and in which rekindling was highly probable. At the same time MIMOSA trained rescue teams. By 20 August 1998, the mine command centre had re-opened the slopes seal. Using a 'Step-by-Step' system, the rescue team began the recovery process by employing cross-cuts and using an auxiliary fan to establish the ventilation circuit. The MIMOSA team advanced into the mine as far as allowed by the water level and was able to recover the main fan. The official mine recovery date was 30 November 1998. Esmeralda Mine was back in operation in December 1998. 1 ref., 3 figs.

  2. Mining robotics sensors

    CSIR Research Space (South Africa)

    Green, JJ

    2012-04-01

    Full Text Available causes of fatalities in underground narrow reef mining. Data are gathered and processed from multiple underground mine sources, and techniques such as surfel modeling and synthetic view generation are explored towards creating visualisations of the data...

  3. Mines and Mineral Resources

    Data.gov (United States)

    Department of Homeland Security — Mines in the United States According to the Homeland Security Infrastructure Program Tiger Team Report Table E-2.V.1 Sub-Layer Geographic Names, a mine is defined as...

  4. MONITORING OF MINING

    Directory of Open Access Journals (Sweden)

    Berislav Šebečić

    1996-12-01

    Full Text Available The way mining was monitored in the past depended on knowledge, interest and the existing legal regulations. Documentary evidence about this work can be found in archives, libraries and museums. In particular, there is the rich archival material (papers and books concerning the work of the one-time Imperial and Royal Mining Captaincies in Zagreb, Zadar, Klagenfurt and Split, A minor part of the documentation has not yet been transferred to Croatia. From mining handbooks and books we can also find out about mining in Croatia. In the context of Austro-Hungary. For example, we can find out that the first governorships in Zagreb and Zadar headed the Ban, Count Jelacic and Baron Mamula were also the top mining authorities, though this, probably from political motives, was suppressed in the guides and inventories or the Mining Captaincies. At the end of the 1850s, Croatia produced 92-94% of sea salt, up to 8.5% of sulphur, 19.5% of asphalt and 100% of oil for the Austro-Hungarian empire. From data about mining in the Split Mining Captaincy, prepared for the Philadephia Exhibition, it can be seen that in the exploratory mining operations in which there were 33,372 independent mines declared in 1925 they were looking mainly for bauxite (60,0%, then dark coal (19,0%, asphalts (10.3% and lignites (62%. In 1931, within the area covered by the same captaincy, of 74 declared mines, only 9 were working. There were five coal mines, three bauxite mines and one for asphalt. I suggest that within state institution, the Mining Captaincy or Authority be renewed, or that a Mining and Geological Authority be set ap, which would lead to the more complete affirmation of Croatian mining (the paper is published in Croatian.

  5. Towards semantic web mining

    OpenAIRE

    Berendt, Bettina; Hotho, Andreas; Stumme, Gerd

    2002-01-01

    Semantic Web Mining aims at combining the two fast-developing research areas Semantic Web and Web Mining. The idea is to improve, on the one hand, the results of Web Mining by exploiting the new semantic structures in the Web; and to make use of Web Mining, on overview of where the two areas meet today, and sketches ways of how a closer integration could be profitable.

  6. Mining in El Salvador

    DEFF Research Database (Denmark)

    Pacheco Cueva, Vladimir

    2014-01-01

    In this guest article, Vladimir Pacheco, a social scientist who has worked on mining and human rights shares his perspectives on a current campaign against mining in El Salvador – Central America’s smallest but most densely populated country.......In this guest article, Vladimir Pacheco, a social scientist who has worked on mining and human rights shares his perspectives on a current campaign against mining in El Salvador – Central America’s smallest but most densely populated country....

  7. Implications of mining practices in an open-pit gold mine for monitoring of a comprehensive test-ban treaty

    Energy Technology Data Exchange (ETDEWEB)

    Jarpe, S.P.; Moran, B.; Goldstein, P.; Glenn, L.A.

    1996-01-01

    This report summarizes the results of an experiment at the Gold Quarry pit, operated by the Newmont Gold Company at Carlin, NV The purpose of the experiment was to obtain local and regional seismic data, together with ``ground truth``, from conventional surface blasting activity and to use these data to help determine the effectiveness with which conventional mining blasts can be discriminated from underground nuclear explosions.

  8. Autonomous mine detection system (AMDS) neutralization payload module

    Science.gov (United States)

    Majerus, M.; Vanaman, R.; Wright, N.

    2010-04-01

    The Autonomous Mine Detection System (AMDS) program is developing a landmine and explosive hazards standoff detection, marking, and neutralization system for dismounted soldiers. The AMDS Capabilities Development Document (CDD) has identified the requirement to deploy three payload modules for small robotic platforms: mine detection and marking, explosives detection and marking, and neutralization. This paper addresses the neutralization payload module. There are a number of challenges that must be overcome for the neutralization payload module to be successfully integrated into AMDS. The neutralizer must meet stringent size, weight, and power (SWaP) requirements to be compatible with a small robot. The neutralizer must be effective against a broad threat, to include metal and plastic-cased Anti-Personnel (AP) and Anti-Tank (AT) landmines, explosive devices, and Unexploded Explosive Ordnance (UXO.) It must adapt to a variety of threat concealments, overburdens, and emplacement methods, to include soil, gravel, asphalt, and concrete. A unique neutralization technology is being investigated for adaptation to the AMDS Neutralization Module. This paper will describe review this technology and how the other two payload modules influence its design for minimizing SWaP. Recent modeling and experimental efforts will be included.

  9. Applying NASA's explosive seam welding

    Science.gov (United States)

    Bement, Laurence J.

    1991-01-01

    The status of an explosive seam welding process, which was developed and evaluated for a wide range of metal joining opportunities, is summarized. The process employs very small quantities of explosive in a ribbon configuration to accelerate a long-length, narrow area of sheet stock into a high-velocity, angular impact against a second sheet. At impact, the oxide films of both surface are broken up and ejected by the closing angle to allow atoms to bond through the sharing of valence electrons. This cold-working process produces joints having parent metal properties, allowing a variety of joints to be fabricated that achieve full strength of the metals employed. Successful joining was accomplished in all aluminum alloys, a wide variety of iron and steel alloys, copper, brass, titanium, tantalum, zirconium, niobium, telerium, and columbium. Safety issues were addressed and are as manageable as many currently accepted joining processes.

  10. Explosives detection system and method

    Science.gov (United States)

    Reber, Edward L.; Jewell, James K.; Rohde, Kenneth W.; Seabury, Edward H.; Blackwood, Larry G.; Edwards, Andrew J.; Derr, Kurt W.

    2007-12-11

    A method of detecting explosives in a vehicle includes providing a first rack on one side of the vehicle, the rack including a neutron generator and a plurality of gamma ray detectors; providing a second rack on another side of the vehicle, the second rack including a neutron generator and a plurality of gamma ray detectors; providing a control system, remote from the first and second racks, coupled to the neutron generators and gamma ray detectors; using the control system, causing the neutron generators to generate neutrons; and performing gamma ray spectroscopy on spectra read by the gamma ray detectors to look for a signature indicative of presence of an explosive. Various apparatus and other methods are also provided.

  11. RANCHERO explosive pulsed power experiments

    CERN Document Server

    Goforth, J H; Armijo, E V; Atchison, W L; Bartos, Yu; Clark, D A; Day, R D; Deninger, W J; Faehl, R J; Fowler, C M; García, F P; García, O F; Herrera, D H; Herrera, T J; Keinigs, R K; King, J C; Lindemuth, I R; López, E; Martínez, E C; Martínez, D; McGuire, J A; Morgan, D; Oona, H; Oro, D M; Parker, J V; Randolph, R B; Reinovsky, R E; Rodríguez, G; Stokes, J L; Sena, F C; Tabaka, L J; Tasker, D G; Taylor, A J; Torres, D T; Anderson, H D; Broste, W B; Johnson, J B; Kirbie, H C

    1999-01-01

    The authors are developing the RANCHERO high explosive pulsed power (HEPP) system to power cylindrically imploding solid-density liners for hydrodynamics experiments. Their near-term goal is to conduct experiments in the regime pertinent to the Atlas capacitor bank. That is, they will attempt to implode liners of ~50 g mass at velocities approaching 15 km/sec. The basic building block of the HEPP system is a coaxial generator with a 304.8 mm diameter stator, and an initial armature diameter of 152 mm. The armature is expanded by a high explosive (HE) charge detonated simultaneously along its axis. The authors have reported a variety of experiments conducted with generator modules 43 cm long and have presented an initial design for hydrodynamic liner experiments. In this paper, they give a synopsis of their first system test, and a status report on the development of a generator module that is 1.4 m long. (6 refs).

  12. Determination of Nanogram Microparticles from Explosives after Real Open-Air Explosions by Confocal Raman Microscopy.

    Science.gov (United States)

    Zapata, Félix; García-Ruiz, Carmen

    2016-07-05

    Explosives are increasingly being used for terrorist attacks to cause devastating explosions. The detection of their postblast residues after an explosion is a high challenge, which has been barely investigated, particularly using spectroscopic techniques. In this research, a novel methodology using confocal Raman microscopy has been developed for the analysis of postblast residues from 10 open-air explosions caused by 10 different explosives (TNT, RDX, PETN, TATP, HMTD, dynamite, black powder, ANFO, chloratite, and ammonal) commonly used in improvised explosive devices. The methodology for the determination of postblast particles from explosives consisted of examining the samples surfaces with both the naked eye, first, and microscopically (10× and 50×), immediately afterward; and finally, analyzing the selected residues by confocal Raman spectroscopy in order to identify the postblast particles from explosives. Interestingly, confocal Raman microscopy has demonstrated to be highly suitable to rapidly, selectively, and noninvasively analyze postblast microscopic particles from explosives up to the nanogram range.

  13. The Kelastic variable wall mining machine. Interim final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-12

    This machine cuts coal along a longwall face extending up to 500 feet by a rotating auger with bits. The machine also transports the coal that is cut acting as screw conveyor. By virtue of an integral shroud comprising part of the conveyor the machine is also amenable to a separation of the zones where men work from air being contaminated by dust and methane gas by the cutting action. Beginning as single intake air courses, the air separates at the working section where one split provides fresh air to the Occupied Zone (OZ) for human needs and the other split purges and carries away dust and methane from face fragmentation in the Cutting Zone (CZ). The attractiveness of the Variable Wall Mining Machine is that it addresses the limitations of current longwall mining equipment: it can consistently out-produce continuous mining machines and most longwall shearing machines. It also is amenable to configuring an environment, the dual-duct system, where the air for human breathing is separated from dust-laden ventilating air with methane mixtures. The objective of the research was to perform a mathematical and experimental study of the interrelationships of the components of the system so that a computer model could demonstrate the workings of the system in an animation program. The analysis resulted in the compilation of the parameters for three different configurations of a dual aircourse system of ventilating underground mines. In addressing the goal of an inherently safe mining system the dual-duct adaptation to the Variable Wall Mining Machine appears to offer the path to solution. The respirable dust problem is solvable; the explosive dust problem is nearly solvable; and the explosive methane problem can be greatly reduced. If installed in a highly gassy mine, the dual duct models would also be considerably less costly.

  14. American mines, methods and men

    Energy Technology Data Exchange (ETDEWEB)

    Walker, S.C.A. (Thames Water Utilities (UK))

    1992-04-01

    The paper is based on the author's visits to a number of American mines, to see their mining machinery and to discuss with mine management their industrial relations problems. The paper gives a brief review of American mines, methods and men and is in the form of a diary. Mines visited are: Ohio Valley Coal Company; Big John Mine; Pittsburgh Research Center of the US Bureau of Mines; Martinka Mine; Robin Hood Complex No 9 Mine (Boone County, West Virginia), Green Briar Mine (Virginia); Martin County Coal (Kentucky); Wabash Mine (Keensburgh, Illinois); Galatia Mine (Harrisburgh, Illinois); and William Station Mine (Sturgis, Kentucky). Details given include mining methods productivity and staffing levels. The mining machinery is described in detail in a separate article. 5 figs.

  15. Data Mining for CRM

    Science.gov (United States)

    Thearling, Kurt

    Data Mining technology allows marketing organizations to better understand their customers and respond to their needs. This chapter describes how Data Mining can be combined with customer relationship management to help drive improved interactions with customers. An example showing how to use Data Mining to drive customer acquisition activities is presented.

  16. EXPLOSION RISK ASSESSMENTS FOR FACILITIES

    Directory of Open Access Journals (Sweden)

    Martin KULICH

    2015-12-01

    Full Text Available In the first part of the article we discuss the possibilities and analytical tools that can deal with the classification of space into zones with danger of explosion for devices with the presence of compressed flammable gases. Then we continue with specifications of possibilities for practical utilization linked to variables such as ventilation degree, hypothetical volume etc., including the examples. At the end we also give a brief overview of software for modelling gas leak, including examples of an outcome.

  17. Trace Explosives Detection by Photoluminescence

    OpenAIRE

    2004-01-01

    Some field tests in counter-terrorism efforts to detect explosive traces employ chemistries that yield colored products. We have examined a test kit of this kind, ETKPlus, based on widely used chemistries and employed extensively by the Israel Police. Our investigation focuses on the prospect of gaining sensitivity by replacing the normal colorimetric modality with photoluminescence detection, which, to our knowledge, has not been explored to date. We find two or more orders of magnitude sens...

  18. LX-10 Explosive Damage Studies

    Science.gov (United States)

    2015-03-03

    Suite NAWCWD TM 8757 6 where P = System pressure Vs = System volume n = Covolume we = Weight of explosive burned F = Impetus, f...simultaneously ignited and regress uniformly, and the regression rate depends only on pressure and propellant temperature. 2. Heat losses from the bomb are...and fired in a manometric closed vessel. The pressure -time history was recorded, and an analysis of the data was performed to evaluate both the

  19. Shell and explosive hydrogen burning

    CERN Document Server

    Boeltzig, A; Cavanna, F; Cristallo, S; Davinson, T; Depalo, R; deBoer, R J; Di Leva, A; Ferraro, F; Imbriani, G; Marigo, P; Terrasi, F; Wiescher, M

    2016-01-01

    The nucleosynthesis of light elements, from helium up to silicon, mainly occurs in Red Giant and Asymptotic Giant Branch stars and Novae. The relative abundances of the synthesized nuclides critically depend on the rates of the nuclear processes involved, often through non-trivial reaction chains, combined with complex mixing mechanisms. In this review, we summarize the contributions made by LUNA experiments in furthering our understanding of nuclear reaction rates necessary for modeling nucleosynthesis in AGB stars and Novae explosions.

  20. Explosion Source Similarity Analysis via SVD

    Science.gov (United States)

    Yedlin, Matthew; Ben Horin, Yochai; Margrave, Gary

    2016-04-01

    An important seismological ingredient for establishing a regional seismic nuclear discriminant is the similarity analysis of a sequence of explosion sources. To investigate source similarity, we are fortunate to have access to a sequence of 1805 three-component recordings of quarry blasts, shot from March 2002 to January 2015. The centroid of these blasts has an estimated location 36.3E and 29.9N. All blasts were detonated by JPMC (Jordan Phosphate Mines Co.) All data were recorded at the Israeli NDC, HFRI, located at 30.03N and 35.03E. Data were first winnowed based on the distribution of maximum amplitudes in the neighborhood of the P-wave arrival. The winnowed data were then detrended using the algorithm of Cleveland et al (1990). The detrended data were bandpass filtered between .1 to 12 Hz using an eighth order Butterworth filter. Finally, data were sorted based on maximum trace amplitude. Two similarity analysis approaches were used. First, for each component, the entire suite of traces was decomposed into its eigenvector representation, by employing singular-valued decomposition (SVD). The data were then reconstructed using 10 percent of the singular values, with the resulting enhancement of the S-wave and surface wave arrivals. The results of this first method are then compared to the second analysis method based on the eigenface decomposition analysis of Turk and Pentland (1991). While both methods yield similar results in enhancement of data arrivals and reduction of data redundancy, more analysis is required to calibrate the recorded data to charge size, a quantity that was not available for the current study. References Cleveland, R. B., Cleveland, W. S., McRae, J. E., and Terpenning, I., Stl: A seasonal-trend decomposition procedure based on loess, Journal of Official Statistics, 6, No. 1, 3-73, 1990. Turk, M. and Pentland, A., Eigenfaces for recognition. Journal of cognitive neuroscience, 3(1), 71-86, 1991.

  1. Fuze for explosive magnetohydrodynamic generator

    Energy Technology Data Exchange (ETDEWEB)

    Webb, G.

    1976-12-23

    An apparatus is examined by which high explosive charges are propelled into and detonated at the center of an MHD-X generator. The high explosive charge units are engaged and propelled by a reciprocating ram device. Detonating in each instance is achieved by striking with a firing pin a detonator charge that is in register with a booster charge, the booster charge being in detonating communication with the high explosive charge. Various safety requirements are satisfied by a spring loaded slider operating in a channel transverse and adjacent to the booster charge. The slide retains the detonator charge out of register with the booster charge until a safety pin that holds the slider in place is pulled by a lanyard attached between the reciprocating ram and the safety pin. Removal of the safety pin permits the detonator charge to slide into alignment with the booster charge. Firing pin actuation is initiated by the slider at the instant the detonator charge and the booster charge come into register.

  2. Thermodynamic States in Explosion Fields

    Energy Technology Data Exchange (ETDEWEB)

    Kuhl, A L

    2010-03-12

    We investigate the thermodynamic states occurring in explosion fields from condensed explosive charges. These states are often modeled with a Jones-Wilkins-Lee (JWL) function. However, the JWL function is not a Fundamental Equation of Thermodynamics, and therefore cannot give a complete specification of such states. We use the Cheetah code of Fried to study the loci of states of the expanded detonation products gases from C-4 charges, and their combustion products air. In the Le Chatelier Plane of specific-internal-energy versus temperature, these loci are fit with a Quadratic Model function u(T), which has been shown to be valid for T < 3,000 K and p < 1k-bar. This model is used to derive a Fundamental Equation u(v,s) for C-4. Given u(v,s), one can use Maxwell's Relations to derive all other thermodynamic functions, such as temperature: T(v,s), pressure: p(v,s), enthalpy: h(v,s), Gibbs free energy: g(v,s) and Helmholz free energy: f(v,s); these loci are displayed in figures for C-4. Such complete equations of state are needed for numerical simulations of blast waves from explosive charges, and their reflections from surfaces.

  3. Nuclear Explosions 1945-1998

    Energy Technology Data Exchange (ETDEWEB)

    Bergkvist, Nils-Olov; Ferm, Ragnhild

    2000-07-01

    The main part of this report is a list of nuclear explosions conducted by the United States, the Soviet Union, the United Kingdom, France, China, India and Pakistan in 1945-98. The list includes all known nuclear test explosions and is compiled from a variety of sources including officially published information from the USA, Russia and France. The details given for each explosion (date, origin time, location, yield, type, etc.) are often compiled from more than one source because the individual sources do not give complete information. The report includes a short background to nuclear testing and provides brief information on the Comprehensive Nuclear-Test-Ban Treaty and the verification regime now being established to verify compliance with the treaty. It also summarizes nuclear testing country by country. The list should be used with some caution because its compilation from a variety of sources means that some of the data could be incorrect. This report is the result of cooperation between the Defence Research Establishment (FOA) and the Stockholm International Peace Research Institute (SIPRI)

  4. Clean, agile alternative binders, additives and plasticizers for propellant and explosive formulations

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, D.M. [Lawrence Livermore National Lab., CA (United States); Hawkins, T.W. [Phillips Lab., Edwards AFB, CA (United States); Lindsay, G.A. [Naval Weapons Station, China Lake, CA (United States)] [and others

    1994-12-01

    As part of the Strategic Environmental Research and Development Program (SERDP) a clean, agile manufacturing of explosives, propellants and pyrotechniques (CANPEP) effort set about to identify new approaches to materials and processes for producing propellants, explosives and pyrotechniques (PEP). The RDX based explosive PBXN-109 and gun propellant M-43 were identified as candidates for which waste minimization and recycling modifications might be implemented in a short time frame. The binders, additives and plasticizers subgroup identified cast non-curable thermoplastic elastomer (TPE) formulations as possible replacement candidates for these formulations. Paste extrudable explosives were also suggested as viable alternatives to PBXN-109. Commercial inert and energetic TPEs are reviewed. Biodegradable and hydrolyzable binders are discussed. The applicability of various types of explosive formulations are reviewed and some issues associated with implementation of recyclable formulations are identified. It is clear that some processing and weaponization modifications will need to be made if any of these approaches are to be implemented. The major advantages of formulations suggested here over PBXN-109 and M-43 is their reuse/recyclability. Formulations using TPE or Paste could by recovered from a generic bomb or propellant and reused if they met specification or easily reprocessed and sold to the mining industry.

  5. Totally confined explosive welding. [apparatus to reduce noise level and protect personnel during explosive bonding

    Science.gov (United States)

    Bement, L. J. (Inventor)

    1974-01-01

    A method and associated apparatus for confining the undesirable by-products and limiting noise of explosive welding are discussed. The apparatus consists fo a simple enclosure into which the explosive is placed and within which the explosion occurs. The shape of the enclosure, the placement of the explosive, and the manner in which the enclosure is placed upon the material to be welded determine the force of the explosion transmitted to the proposed bond area. The explosion is totally confined within the enclosure thus reducing the noise level and preventing debris from being strewn about to contaminate the weld area or create personnel hazards.

  6. Mining text data

    CERN Document Server

    Aggarwal, Charu C

    2012-01-01

    Text mining applications have experienced tremendous advances because of web 2.0 and social networking applications. Recent advances in hardware and software technology have lead to a number of unique scenarios where text mining algorithms are learned. ""Mining Text Data"" introduces an important niche in the text analytics field, and is an edited volume contributed by leading international researchers and practitioners focused on social networks & data mining. This book contains a wide swath in topics across social networks & data mining. Each chapter contains a comprehensive survey including

  7. Detection of explosive remnants of war by neutron thermalisation

    Energy Technology Data Exchange (ETDEWEB)

    Brooks, F.D., E-mail: frank.brooks@uct.ac.za [Department of Physics, University of Cape Town, Rondebosch 7701 (South Africa); Drosg, M. [Faculty of Physics, University of Vienna, Wien A-1090 (Austria); Smit, F.D.; Wikner, C. [iThemba Laboratory for Accelerator-Based Sciences, Somerset West 7129 (South Africa)

    2012-01-15

    The HYDAD-D landmine detector () has been modified and field-tested for 17 months in a variety of soil conditions. Test objects containing about the same mass of hydrogen (20 g) as small explosive remnants of war, such as antipersonnel landmines, were detected with efficiency 100% when buried at cover depths up to 10 cm. The false alarm rate under the same conditions was 9%. Plots of detection efficiency versus false alarm rate are presented. - Highlights: Black-Right-Pointing-Pointer A new version of the HYDAD-D antipersonnel landmine detector is described. Black-Right-Pointing-Pointer Field tests were carried out for 17 months under different conditions. Black-Right-Pointing-Pointer Dummy antipersonnel mines were detected with 100% efficiency at cover depths up to 10 cm. Black-Right-Pointing-Pointer Results are presented as plots of landmine detection efficiency versus false alarm rate.

  8. Configurational order-disorder induced metal-nonmetal transition in B13C2 studied with first-principles superatom-special quasirandom structure method

    Science.gov (United States)

    Ektarawong, A.; Simak, S. I.; Hultman, L.; Birch, J.; Alling, B.

    2015-07-01

    Due to a large discrepancy between theory and experiment, the electronic character of crystalline boron carbide B13C2 has been a controversial topic in the field of icosahedral boron-rich solids. We demonstrate that this discrepancy is removed when configurational disorder is accurately considered in the theoretical calculations. We find that while the ordered ground state B13C2 is metallic, the configurationally disordered B13C2 , modeled with a superatom-special quasirandom structure method, goes through a metal to nonmetal transition as the degree of disorder is increased with increasing temperature. Specifically, one of the chain-end carbon atoms in the CBC chains substitutes a neighboring equatorial boron atom in a B12 icosahedron bonded to it, giving rise to a B11Ce (BBC) unit. The atomic configuration of the substitutionally disordered B13C2 thus tends to be dominated by a mixture between B12(CBC) and B11Ce (BBC). Due to splitting of valence states in B11Ce (BBC), the electron deficiency in B12(CBC) is gradually compensated.

  9. The effects of nonmetal dopants on the electronic, optical and chemical performances of monolayer g-C3N4 by first-principles study

    Science.gov (United States)

    Lu, S.; Li, C.; Li, H. H.; Zhao, Y. F.; Gong, Y. Y.; Niu, L. Y.; Liu, X. J.; Wang, T.

    2017-01-01

    Doping is an effective means to alter the electronic behavior of materials by forming new chemical bond and relaxing the surrounding chemical bonds. With the aid of first-principle studies, the effects of a series of nonmetal (NM) dopants on the geometric, thermodynamic, electronic and optical performances of monolayer g-C3N4 have been investigated. Results shown that, all considered NM atoms except Br and I atoms can be introduced into the monolayer g-C3N4 on account of the thermal stability, the supercell parameter and film thickness have been altered by the newly formed Csbnd NM bonds and the relaxed chemical bonds around them, which have affected their electronic structure. The band gap values were altered less than ±0.14 eV. The optical absorption edge (and intensity) in visible light of all doped specimens red-shift 10-75 nm (and increase about 14%-71%) except for O- and S-doped specimens, and thus the NM dopants can enhance the visible-light response capability. Moreover, the highest occupied molecular orbital and lowest unoccupied molecular orbital of H-, B-, O-, S-, F- and As-doped specimens have been separated adequately, it can effectively separate the photogenerated e-/h+ pairs and enhance the photocatalytic efficiency. Finally, we have confirmed six high efficiency monolayer g-C3N4 based photocatalysts by doping H, B, O, S, F and As atoms.

  10. Data mining in radiology.

    Science.gov (United States)

    Kharat, Amit T; Singh, Amarjit; Kulkarni, Vilas M; Shah, Digish

    2014-04-01

    Data mining facilitates the study of radiology data in various dimensions. It converts large patient image and text datasets into useful information that helps in improving patient care and provides informative reports. Data mining technology analyzes data within the Radiology Information System and Hospital Information System using specialized software which assesses relationships and agreement in available information. By using similar data analysis tools, radiologists can make informed decisions and predict the future outcome of a particular imaging finding. Data, information and knowledge are the components of data mining. Classes, Clusters, Associations, Sequential patterns, Classification, Prediction and Decision tree are the various types of data mining. Data mining has the potential to make delivery of health care affordable and ensure that the best imaging practices are followed. It is a tool for academic research. Data mining is considered to be ethically neutral, however concerns regarding privacy and legality exists which need to be addressed to ensure success of data mining.

  11. Data mining in radiology

    Directory of Open Access Journals (Sweden)

    Amit T Kharat

    2014-01-01

    Full Text Available Data mining facilitates the study of radiology data in various dimensions. It converts large patient image and text datasets into useful information that helps in improving patient care and provides informative reports. Data mining technology analyzes data within the Radiology Information System and Hospital Information System using specialized software which assesses relationships and agreement in available information. By using similar data analysis tools, radiologists can make informed decisions and predict the future outcome of a particular imaging finding. Data, information and knowledge are the components of data mining. Classes, Clusters, Associations, Sequential patterns, Classification, Prediction and Decision tree are the various types of data mining. Data mining has the potential to make delivery of health care affordable and ensure that the best imaging practices are followed. It is a tool for academic research. Data mining is considered to be ethically neutral, however concerns regarding privacy and legality exists which need to be addressed to ensure success of data mining.

  12. Commercial Data Mining Software

    Science.gov (United States)

    Zhang, Qingyu; Segall, Richard S.

    This chapter discusses selected commercial software for data mining, supercomputing data mining, text mining, and web mining. The selected software are compared with their features and also applied to available data sets. The software for data mining are SAS Enterprise Miner, Megaputer PolyAnalyst 5.0, PASW (formerly SPSS Clementine), IBM Intelligent Miner, and BioDiscovery GeneSight. The software for supercomputing are Avizo by Visualization Science Group and JMP Genomics from SAS Institute. The software for text mining are SAS Text Miner and Megaputer PolyAnalyst 5.0. The software for web mining are Megaputer PolyAnalyst and SPSS Clementine . Background on related literature and software are presented. Screen shots of each of the selected software are presented, as are conclusions and future directions.

  13. Data mining in radiology

    Science.gov (United States)

    Kharat, Amit T; Singh, Amarjit; Kulkarni, Vilas M; Shah, Digish

    2014-01-01

    Data mining facilitates the study of radiology data in various dimensions. It converts large patient image and text datasets into useful information that helps in improving patient care and provides informative reports. Data mining technology analyzes data within the Radiology Information System and Hospital Information System using specialized software which assesses relationships and agreement in available information. By using similar data analysis tools, radiologists can make informed decisions and predict the future outcome of a particular imaging finding. Data, information and knowledge are the components of data mining. Classes, Clusters, Associations, Sequential patterns, Classification, Prediction and Decision tree are the various types of data mining. Data mining has the potential to make delivery of health care affordable and ensure that the best imaging practices are followed. It is a tool for academic research. Data mining is considered to be ethically neutral, however concerns regarding privacy and legality exists which need to be addressed to ensure success of data mining. PMID:25024513

  14. Physical and technological factors of the formation of detonation capacity of blasthole charges of emulsion explosives

    Directory of Open Access Journals (Sweden)

    Poplavsky V.A.

    2017-04-01

    Full Text Available Modern conditions of mining are characterized by a constant increase in the depth of the pit, as a result of this there is a change in the geological and mining conditions. The obtaining of the mined rock is provided by using the drilling-and-blasting method as the main process that influences the technical and economic indicators of the next processes and enterprises in general. The effectiveness of the explosion in rocks depends on the technology of blasting. In scientific and technical literature the influence of various natural and technological factors on the process of the explosion has been studied in detail. We developed methods and recommendations for calculating the parameters of mass blasting used in common projects in the blasting operation and ensure their implementation of getting the rock mass of different coarseness of grading. However, these methods are based on traditional formulas and empirical dependencies, according to which the parameters of location and charge blasting accepted as the same, despite the fact that the blocks that blasted may include different types of rocks, and this, in turn, causes predatory yield of sub-standard fractions. Therefore, the implementation of the design parameters of the blasting should be based on modern scientific achievements, interrelationships of geological and technological indicators and parameters with the least expenditure of labor and time in the design process. The article analyzes the impact of the physical condition and the composition of emulsion explosive, geometric parameters and conditions of charge blasting, characteristics of dynamic processes in the charge and the decomposed array for the manifestation of the phenomenon of desensibilization emulsion explosives. Keywords: desensibilization; detonation speed; critical diameter; ; hydrostatic pressure; gas-generating process; shock wave; boulder.

  15. ANFO and TNT anti-vehicle mine blast: Experimental and numerical observations

    NARCIS (Netherlands)

    Tyler-Street, M.; Leerdam, P.J.; Verhoeven, T.

    2014-01-01

    Anti-vehicle (AV) mines and Improvised Explosive Devices (IEDs) pose a major threat in recent and current missions. In the latest operational theatres of Iraq and Afghanistan they have been responsible for a significant proportion of all casualties. Understanding both the characteristics and strengt

  16. Infrared processing and sensor fusion for anti-personnel land-mine detection

    NARCIS (Netherlands)

    Schavemaker, J.G.M.; Cremer, F.; Schutte, K.; Breejen, E. den

    2000-01-01

    In this paper we present the results of infrared processing and sensor fusion obtained within the European research project GEODE (Ground Explosive Ordnance DEtection) that strives for the realization of a vehicle-mounted, multi-sensor anti-personnel land-mine detection system for humanitarian demin

  17. Preliminary field exploration in the bituminous coal mining with impulse radar

    Energy Technology Data Exchange (ETDEWEB)

    Thyssen, F.; Schepers, R.

    1983-06-01

    A laboratory measuring station to determine the physical characteristics of coal has been built up and measurements have been carried out with samples from different seams. Underground radar measurements were carried out in the experimental mine Tremonia with a non-explosion-proof apparatus. The development of a intrinsicly safe radar apparatus for underground measurements has been chiefly terminated.

  18. On the Detection of Drifting Sea Mines using Above- and Underwater Sensors

    NARCIS (Netherlands)

    Dol, H.S.; Sabel, J.C.; Lensen, H.A.; Beckers, A.L.D.

    2010-01-01

    Small drifting objects can be a big threat to surface ships, especially when the objects are explosion hazards like sea mines that have become detached from their moorings. Timely detection of such objects is crucial in order to be able to perform adequate evasive manoeuvres. However, the vertical p

  19. ANFO and TNT anti-vehicle mine blast: Experimental and numerical observations

    NARCIS (Netherlands)

    Tyler-Street, M.; Leerdam, P.J.; Verhoeven, T.

    2014-01-01

    Anti-vehicle (AV) mines and Improvised Explosive Devices (IEDs) pose a major threat in recent and current missions. In the latest operational theatres of Iraq and Afghanistan they have been responsible for a significant proportion of all casualties. Understanding both the characteristics and strengt

  20. Blasting chamber of the mine water stained; Voladuras de avance en labores subterraneas

    Energy Technology Data Exchange (ETDEWEB)

    Domingo Perlado, J. F.

    2012-11-01

    In this paper, the main parameters that lay out a developed blast in underground mining are studied. Such parameters affect the geometry of the draft scheme so as to get a regular cut with a minimum consumption of explosive in order to reduce the vibrations caused by blasting. (Author)

  1. Detection of anti-personnel land-mines using sensor-fusion techniques

    NARCIS (Netherlands)

    Cremer, F.; Schavemaker, J.G.M.; Breejen, E. den; Schutte, K.

    1999-01-01

    In this paper we present the sensor-fusion results based on the measurements obtained within the European research project GEODE (Ground Explosive Ordnance DEtection system) that strives for the realisation of a vehicle-mounted, multisensor, anti-personnel land-mine detection system for humanitarian

  2. Thermal explosion in oscillating ambient conditions

    Science.gov (United States)

    Novozhilov, Vasily

    2016-07-01

    Thermal explosion problem for a medium with oscillating ambient temperature at its boundaries is considered. This is a new problem in thermal explosion theory, not previously considered in a distributed system formulation, but important for combustion and fire science. It describes autoignition of wide range of fires (such as but not limited to piles of biosolids and other organic matter; storages of munitions, explosives, propellants) subjected to temperature variations, such as seasonal or day/night variation. The problem is considered in formulation adopted in classical studies of thermal explosion. Critical conditions are determined by frequency and amplitude of ambient temperature oscillations, as well as by a number of other parameters. Effects of all the parameters on critical conditions are quantified. Results are presented for the case of planar symmetry. Development of thermal explosion in time is also considered, and a new type of unsteady thermal explosion development is discovered where thermal runaway occurs after several periods of temperature oscillations within the medium.

  3. Numerical computations of explosions in gases

    Science.gov (United States)

    Chushkin, P. I.; Shurshalov, L. V.

    The development and the present-day state of the problem on numerical computations of explosions in gases are reviewed. In the first part, different one-dimensional cases are discussed: point explosion with counterpressure, blast-like expansion of volumes filled with a compressed hot gas, blast of charges of condensed explosive, explosion processes in real high-temperature air, in combustible detonating media and under action of other physical-chemical factors. In the second part devoted to two-dimensional flows, we consider explosion in the non-homogeneous atmosphere, blast of asymmetric charges, detonation in gas, explosion modelling of some cosmic phenomena (solar flares, the Tunguska meteorite). The survey includes about 110 works beginning with the first publications on the subject.

  4. Coal mine safety achievements in the USA and the contribution of NIOSH research

    Energy Technology Data Exchange (ETDEWEB)

    Esterhuizen, G.S.; Gurtunca, R.G. [NIOSH, Washington, DC (United States)

    2006-12-15

    Over the past century coal miner safety and health have seen tremendous improvements: the fatality and injury rates continue to decrease while productivity continues to increase. Many of the hazards that plagued miners in the past, such as coal bumps, methane and coal dust explosions, ground fall accidents and health issues have been significantly reduced. The contribution of NIOSH research includes products for prevention and survival of mine fires, methane control measures, design procedure for underground coal mines, methods for excavation surface controls, methods and procedures for blasting, laser usage in underground mines and prevention of electrocution from overhead power lines that have reduced accidents and injuries in underground coal mines. Health research has produced products such as the personal dust monitor, noise abating technologies and ergonomic solutions for equipment operators. Research priorities at NIOSH are set by considering surveillance statistics, stakeholder inputs and loss control principles. Future research in coal mining is directed towards respiratory diseases, noise-induced hearing loss, repetitive musculoskeletal injuries, traumatic injuries, falls of ground and mine disasters. The recent spate of accidents in coal mines resulted in the Miner Act of 2006, which includes a specific role for NIOSH in future mine safety research and development. The mine safety achievements in the USA reflect the commitment of industry, labour, government and research organizations to improving the safety of the mine worker.

  5. From Sequential Pattern Mining to Structured Pattern Mining: A Pattern-Growth Approach

    Institute of Scientific and Technical Information of China (English)

    Jia-WeiHan; JianPei; Xi-FengYan

    2004-01-01

    Sequential pattern mining is an important data mining problem with broad applications. However, it is also a challenging problem since the mining may have to generate or examine a combinatorially explosive number of intermediate subsequences. Recent studies have developed two major classes of sequential pattern mining methods: (1) a candidate generation-and-test approach, represented by (i) GSP, a horizontal format-based sequential pattern mining method, and (ii) SPADE, a vertical format-based method; and (2) a pattern-growth method, represented by PrefixSpan and its further extensions, such as gSpan for mining structured patterns. In this study, we perform a systematic introduction and presentation of the pattern-growth methodology and study its principles and extensions. We first introduce two interesting pattern-growth algorithms, FreeSpan and PrefixSpan, for efficient sequential pattern mining. Then we introduce gSpan for mining structured patterns using the same methodology. Their relative performance in large databases is presented and analyzed. Several extensions of these methods are also discussed in the paper, including mining multi-level, multi-dimensional patterns and mining constraint-based patterns.

  6. Workplace Air Quality at Explosive Material Manufacturing and Handling Units

    Directory of Open Access Journals (Sweden)

    G. K. Kannan

    2006-10-01

    Full Text Available Worldwide, large quantities of explosives are manufactured for use in various types ofammunitions, arms, and mines. Toxic pollutants in the workplaces of three major activities, viz.,explosive and solid propellant preparation facility, solid propellant shell assembling facility, andsolid propellant shell proof firing facility, were studied. The suspended particulate matter (SPMconcentration in grinding room (13.9 mg/m3 and sieving room (19.3 mg/m3 of solid propellantpreparation facility was observed to be two to threefold higher than the permissible limit. TheSPM in the dentex preparation section was found to be significantly high (10.8 mg/m3. Thepersonal exposure was fourfold higher (21 mg/m3 than the permissible limit. It was emerged thatconcentration of particulate is a major concern in all the processing sections. Since the chemicalnature of these particulates is expected to be more toxic in nature, it requires greater attention.At firing point, carbon monoxide appeared to be a major concern.

  7. Wireless system for explosion detection in underground structures

    Science.gov (United States)

    Chikhradze, M.; Bochorishvili, N.; Akhvlediani, I.; Kukhalashvili, D.; Kalichava, I.; Mataradze, E.

    2009-06-01

    Considering the growing threat of terrorist or accidental explosions in underground stations, underground highway and railway sections improvement of system for protecting people from explosions appears urgent. Current automatic protective devices with blast identification module and blast damping absorbers of various designs as their basic elements cannot be considered effective. Analysis revealed that low reliability of blast detection and delayed generation of start signal for the activation of an absorber are the major disadvantages of protective devices. Besides the transmission of trigger signal to an energy absorber through cable communication reduces the reliability of the operation of protective device due to a possible damage of electric wiring under blast or mechanical attack. This paper presents the outcomes of the studies conducted to select accurate criteria for blast identification and to design wireless system of activation of defensive device. The results of testing of blast detection methods (seismic, EMP, optical, on overpressure) showed that the proposed method, which implies constant monitoring of overpressure in terms of its reliability and response speed, best meets the requirements. Proposed wireless system for explosions identification and activation of protective device consists of transmitter and receiver modules. Transmitter module contains sensor and microprocessor equipped with blast identification software. Receiver module produces activation signal for operation of absorber. Tests were performed in the underground experimental base of Mining Institute. The time between the moment of receiving signal by the sensor and activation of absorber - 640 microsecond; distance between transmitter and receiver in direct tunnel - at least 150m; in tunnel with 900 bending - 50m. This research is sponsored by NATO's Public Diplomacy Division in the framework of "Science for Peace".

  8. Optical detection of buried explosive hazards: a longitudinal comparison of three types of imagery

    Science.gov (United States)

    Staszewski, James J.; Hibbitts, Charles H.; Davis, Luke; Bursley, James

    2013-06-01

    Visual detection of soil disturbances is a surprisingly effective, but far from perfect way of detecting buried explosive threats such as landmines and improvised explosive devices (IEDs). This effort builds upon the few systematic studies of optical detection in this area. It investigates observer sensitivity to optical information produced by the burial of anti-tank and small anti-personnel landmines asking "How detectable are disturbed soil signatures captured in visible (VIS), shortwave infrared (SWIR), and thermal infrared (TIR), bands?" "Which band or bands are most effective for detection?" and "How well does each band support detection in the natural environment over time?" Using signal detection procedures this study presented young adults photographs showing soil disturbed by landmine burial or adjacent undisturbed surfaces with instructions to make decisions about the presence or absence of a disturbance. Stimuli spanned a six-week time period over which VIS, SWIR, and TIR imagery was collected. Results show that (a) signal strength persists surprisingly well over the observation period, (b) generally, SWIR and VIS show consistently strong performance for large anti-tank mines and SWIR shows the soil signature for the small, anti-personnel mine remarkably well. TIR lags the other two bands when using d' to measure performance, but shows promising hit rates for anti-tank mine signatures under appropriate conditions. Generally, results show that the SWIR and VIS bands show most promise as a practical means of explosive hazards detection, although TIR can work effectively for large anti-tank mines under certain conditions. Limitations and implications for further research are discussed.

  9. In the beginning, the Box Flat mining disaster 1972

    Energy Technology Data Exchange (ETDEWEB)

    Colin Hester

    2006-10-15

    This is the second of a series of historical pieces from the author recalling less complicated days of mining; days of an age when coal and ore were just as important as they are today but technology and safety were less well developed. This story is drawn from Government records of enquiry and newspaper articles of the day. It recounts the fire and explosion caused by spontaneous combustion of coal in No. 5 mine of the Box Flat Extended Collieries in Ipswich, Queensland on 31 July 1972. Each character is a real person; every mine manager, miner, investigator and relative is a real person, and they acted as real people do when confronted by disaster. With the advantages of hindsight and modernity, the hour of their lives that have been recorded forever. One must not judge them too harshly; there are things we can learn from them not least of which is how we made it this far. 4 refs., 2 photos.

  10. Lunar construction/mining equipment

    Science.gov (United States)

    Ozdemir, Levent

    1990-01-01

    For centuries, mining has utilized drill and blast as the primary method of rock excavation. Although this technique has undergone significant improvements, it still remains a cyclic, labor intensive operation with inherent safety hazards. Other drawbacks include damage to the surrounding ground, creation of blast vibrations, rough excavation walls resulting in increased ventilation requirements, and the lack of selective mining ability. Perhaps the most important shortcoming of drill and blast is that it is not conducive to full implementation of automation or robotics technologies. Numerous attempts have been made in the past to automate drill and blast operations to remove personnel from the hazardous work environment. Although most of the concepts devised look promising on paper, none of them was found workable on a sustained production basis. In particular, the problem of serious damage to equipment during the blasting cycle could not be resolved regardless of the amount of charge used in excavation. Since drill and blast is not capable of meeting the requirements of a fully automated rock fragmentation method, its role is bound to gradually decrease. Mechanical excavation, in contrast, is highly suitable to automation because it is a continuous process and does not involve any explosives. Many of the basic principles and trends controlling the design of an earth-based mechanical excavator will hold in an extraterrestrial environment such as on the lunar surface. However, the economic and physical limitations for transporting materials to space will require major rethinking of these machines. In concept, then, a lunar mechanical excavator will look and perform significantly different from one designed for use here on earth. This viewgraph presentation gives an overview of such mechanical excavator systems.

  11. Momentum transfer in indirect explosive drive

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, J.E.; Warnes, R.H. [Los Alamos National Lab., NM (United States); Cherry, C.R.; Cherry, C.R. Jr.; Fischer, S.H. [Sandia National Labs., Albuquerque, NM (United States)

    1996-07-01

    Material which is not in direct contact with detonating explosives may still be driven by the explosion through impact by driven material or by attachment to driven material. In such circumstances the assumption of inelastic collision permits estimation of the final velocity of an assemblage. Examples of the utility of this assumption are demonstrated through use of Gurney equations. The inelastic collision calculation may also be used for metal parts which are driven by explosives partially covering the metal. We offer a new discounting angle to account for side energy losses from laterally unconfined explosive charges in cases where the detonation wave travels parallel to the surface which is driven.

  12. Method and apparatus for detecting explosives

    Science.gov (United States)

    Moore, David Steven [Santa Fe, NM

    2011-05-10

    A method and apparatus is provided for detecting explosives by thermal imaging. The explosive material is subjected to a high energy wave which can be either a sound wave or an electromagnetic wave which will initiate a chemical reaction in the explosive material which chemical reaction will produce heat. The heat is then sensed by a thermal imaging device which will provide a signal to a computing device which will alert a user of the apparatus to the possibility of an explosive device being present.

  13. Explosive Field Visualization Based on Image Fusion

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wen-yao; JIANG Ling-shuang

    2009-01-01

    m the composite sequence. Experimental results show that the new images integrate the advantages of sources, effectively improve the visualization, and disclose more information about explosive field.

  14. High Explosives Research and Development (HERD) Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The purpose is to provide high explosive formulation, chemical analysis, safety and performance testing, processing, X-ray, quality control and loading support for...

  15. 27 CFR 555.181 - Reporting of plastic explosives.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Reporting of plastic..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.181 Reporting of plastic explosives. All persons, other than an agency of the United...

  16. 27 CFR 70.445 - Commerce in explosives.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Commerce in explosives. 70... Cartridges, and Explosives § 70.445 Commerce in explosives. Part 55 of title 27 CFR contains the regulations..., explosives, (b) Permits for users who buy or transport explosives in interstate or foreign commerce,...

  17. 29 CFR 1926.902 - Surface transportation of explosives.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Surface transportation of explosives. 1926.902 Section 1926... Explosives § 1926.902 Surface transportation of explosives. (a) Transportation of explosives shall meet the... Carriers. (b) Motor vehicles or conveyances transporting explosives shall only be driven by, and be in the...

  18. 29 CFR 1926.903 - Underground transportation of explosives.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Underground transportation of explosives. 1926.903 Section... Explosives § 1926.903 Underground transportation of explosives. (a) All explosives or blasting agents in... explosives or blasting agents taken to an underground loading area shall not exceed the amount estimated to...

  19. 27 CFR 555.63 - Explosives magazine changes.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Explosives magazine..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Licenses and Permits § 555.63 Explosives magazine changes. (a) General. (1) The requirements of this section are applicable...

  20. General phenomenology of underground nuclear explosions; Phenomenologie generale des explosions nucleaires souterraines

    Energy Technology Data Exchange (ETDEWEB)

    Derlich, S.; Supiot, F. [Commissariat a l' Energie Atomique, Bruyeres-le-Chatel (France). Centre d' Etudes

    1969-07-01

    An essentially qualitatively description is given of the phenomena related to underground nuclear explosions (explosion of a single unit, of several units in line, and simultaneous explosions). In the first chapter are described the phenomena which are common to contained explosions and to explosions forming craters (formation and propagation of a shock-wave causing the vaporization, the fusion and the fracturing of the medium). The second chapter describes the phenomena related to contained explosions (formation of a cavity with a chimney). The third chapter is devoted to the phenomenology of test explosions which form a crater; it describes in particular the mechanism of formation and the different types of craters as a function of the depth of the explosion and of the nature of the ground. The aerial phenomena connected with explosions which form a crater: shock wave in the air and focussing at a large distance, and dust clouds, are also dealt with. (authors) [French] On donne une description essentiellement qualitative des phenomenes lies aux explosions nucleaires souterraines (explosion d'un seul engin, d'engins en ligne et explosions simultanees). Dans un premier chapitre sont decrits les phenomenes communs aux explosions contenues et aux explosions formant un cratere (formation et propagation d'une onde de choc provoquant la vaporisation, la fusion et la fracturation du milieu). Le deuxieme chapitre decrit les phenomenes lies aux tirs contenus (formation d'une cavite et d'une cheminee). Le troisieme chapitre est consacre a la phenomenologie des tirs formant un cratere et decrit notamment le mecanisme de formation et les differents types de crateres en fonction de la profondeur d'explosion et de la nature du terrain. Les phenomenes aeriens lies aux explosions formant un cratere: onde de pression aerienne et focalisation a grande distance, nuages de poussieres, sont egalement abordes. (auteurs)

  1. An Incremental High-Utility Mining Algorithm with Transaction Insertion

    Directory of Open Access Journals (Sweden)

    Jerry Chun-Wei Lin

    2015-01-01

    Full Text Available Association-rule mining is commonly used to discover useful and meaningful patterns from a very large database. It only considers the occurrence frequencies of items to reveal the relationships among itemsets. Traditional association-rule mining is, however, not suitable in real-world applications since the purchased items from a customer may have various factors, such as profit or quantity. High-utility mining was designed to solve the limitations of association-rule mining by considering both the quantity and profit measures. Most algorithms of high-utility mining are designed to handle the static database. Fewer researches handle the dynamic high-utility mining with transaction insertion, thus requiring the computations of database rescan and combination explosion of pattern-growth mechanism. In this paper, an efficient incremental algorithm with transaction insertion is designed to reduce computations without candidate generation based on the utility-list structures. The enumeration tree and the relationships between 2-itemsets are also adopted in the proposed algorithm to speed up the computations. Several experiments are conducted to show the performance of the proposed algorithm in terms of runtime, memory consumption, and number of generated patterns.

  2. Static Charge Development on Explosives .

    Directory of Open Access Journals (Sweden)

    K. Raha

    1991-01-01

    Full Text Available Static charge development character of some of the important explosive crystals have been predicted on the basis of their crystal class and symmetry. Among the important mechanism of charge development, the piezoelectric and pyroelectric characters have been considered. Ammonium trinitrate, ammonium nitrate, m-dinitro-benzene, trinitro-toluene, styphnic acid, beeta-lead styphnate, 4,4'dinitro-dipheny1, a-hexamethylenetetranitramine, nitroguanidine, picric acid, dimethylnitramine, a-lead azide and beeta-lead azide are pyroelectric in nature, whereas pentaerythritol tetranitrate, picryliodide, hexamethylenetranitramine, tetranitromethane and trinitroethane are piezoelectric in nature.

  3. The gas dynamics of explosions

    CERN Document Server

    Lee,\tJohn H S

    2016-01-01

    Explosions, and the non-steady shock propagation associated with them, continue to interest researchers working in different fields of physics and engineering (such as astrophysics and fusion). Based on the author's course in shock dynamics, this book describes the various analytical methods developed to determine non-steady shock propagation. These methods offer a simple alternative to the direct numerical integration of the Euler equations and offer a better insight into the physics of the problem. Professor Lee presents the subject systematically and in a style that is accessible to graduate students and researchers working in shock dynamics, combustion, high-speed aerodynamics, propulsion and related topics.

  4. Reliability of Hydrox explosive blasting

    Energy Technology Data Exchange (ETDEWEB)

    Chikunov, V.I.; Chulkov, O.G.; Domanov, V.P.

    1980-03-01

    The safest method of blasting in coal mines with methane and coal dust hazards is with the flameless Hydrox charges. The results of operational tests on Hydrox BV-A2U charges with a I-43 initiator in underground coal mines are discussed. Efficiency and reliability of blasting using Hydrox BV-A2U compared to BV-48 Hydrox charges is evaluated. Results of blasting and the percentage of charge failures are given in tables. It is suggested that BV-A2U Hydrox charges are superior to BV-48, as no charge failures occur, operational time of BV-A2U is up to 5 seconds and the maximum operational time spread is 1.8 sec (weight of initiator 0.05 kg). Blasting properties of BV-A2U are stable and do not change as a result of long storage. (In Russian)

  5. A structured approach to forensic study of explosions: The TNO Inverse Explosion Analysis tool

    NARCIS (Netherlands)

    Voort, M.M. van der; Wees, R.M.M. van; Brouwer, S.D.; Jagt-Deutekom, M.J. van der; Verreault, J.

    2015-01-01

    Forensic analysis of explosions consists of determining the point of origin, the explosive substance involved, and the charge mass. Within the EU FP7 project Hyperion, TNO developed the Inverse Explosion Analysis (TNO-IEA) tool to estimate the charge mass and point of origin based on observed damage

  6. 75 FR 1085 - Commerce in Explosives; List of Explosive Materials (2009R-18T)

    Science.gov (United States)

    2010-01-08

    ... [Federal Register Volume 75, Number 5 (Friday, January 8, 2010)] [Notices] [Pages 1085-1087] [FR Doc No: 2010-45] DEPARTMENT OF JUSTICE Bureau of Alcohol, Tobacco, Firearms and Explosives [Docket No. ATF 34N] Commerce in Explosives; List of Explosive Materials (2009R-18T) AGENCY: Bureau of...

  7. Mine your own business! Mine other's news!

    OpenAIRE

    Pham, Quang-Khai; Saint-Paul, Régis; Benatallah, Boualem; Mouaddib, Noureddine; Raschia, Guillaume

    2008-01-01

    International audience; Major media companies such as The Financial Times, the Wall Street Journal or Reuters generate huge amounts of textual news data on a daily basis. Mining frequent patterns in this mass of information is critical for knowledge workers such as financial analysts, stock traders or economists. Using existing frequent pattern mining (FPM) algorithms for the analysis of news data is difficult because of the size and lack of structuring of the free text news content. In this ...

  8. Data mining, mining data : energy consumption modelling

    Energy Technology Data Exchange (ETDEWEB)

    Dessureault, S. [Arizona Univ., Tucson, AZ (United States)

    2007-09-15

    Most modern mining operations are accumulating large amounts of data on production and business processes. Data, however, provides value only if it can be translated into information that appropriate users can utilize. This paper emphasized that a new technological focus should emerge, notably how to concentrate data into information; analyze information sufficiently to become knowledge; and, act on that knowledge. Researchers at the Mining Information Systems and Operations Management (MISOM) laboratory at the University of Arizona have created a method to transform data into action. The data-to-action approach was exercised in the development of an energy consumption model (ECM), in partnership with a major US-based copper mining company, 2 software companies, and the MISOM laboratory. The approach begins by integrating several key data sources using data warehousing techniques, and increasing the existing level of integration and data cleaning. An online analytical processing (OLAP) cube was also created to investigate the data and identify a subset of several million records. Data mining algorithms were applied using the information that was isolated by the OLAP cube. The data mining results showed that traditional cost drivers of energy consumption are poor predictors. A comparison was made between traditional methods of predicting energy consumption and the prediction formed using data mining. Traditionally, in the mines for which data were available, monthly averages of tons and distance are used to predict diesel fuel consumption. However, this article showed that new information technology can be used to incorporate many more variables into the budgeting process, resulting in more accurate predictions. The ECM helped mine planners improve the prediction of energy use through more data integration, measure development, and workflow analysis. 5 refs., 11 figs.

  9. 非金属元素掺杂改性TiO2的光催化性能%The Photocatalytic Performance of Nonmetal Elements Doping TiO2

    Institute of Scientific and Technical Information of China (English)

    蔡河山; 刘国光; 余林; 熊心美

    2005-01-01

      通过非金属掺杂改性的方法可以将只能UV光激发的TiO2光催化反应红移到可见光区域进行。文中介绍了非金属N、S等元素掺杂改性TiO2,指出金属与非金属复合掺杂改性TiO2是今后的一个重要研究方向,并存在巨大的研究空间。%  Through the method of nonmetal elements doping and modifying TiO2, the photocatalytic reaction which excited only under UV-light can be excited under the visible light region. This paper introduces the progress of the nonmetal elements, such as N, S, etc. doping and modifying TiO2. The codoping(metal and nonmetal ) method might be an important research direction in the future to modify TiO2.

  10. Spatiotemporal Data Mining: A Computational Perspective

    Directory of Open Access Journals (Sweden)

    Shashi Shekhar

    2015-10-01

    Full Text Available Explosive growth in geospatial and temporal data as well as the emergence of new technologies emphasize the need for automated discovery of spatiotemporal knowledge. Spatiotemporal data mining studies the process of discovering interesting and previously unknown, but potentially useful patterns from large spatiotemporal databases. It has broad application domains including ecology and environmental management, public safety, transportation, earth science, epidemiology, and climatology. The complexity of spatiotemporal data and intrinsic relationships limits the usefulness of conventional data science techniques for extracting spatiotemporal patterns. In this survey, we review recent computational techniques and tools in spatiotemporal data mining, focusing on several major pattern families: spatiotemporal outlier, spatiotemporal coupling and tele-coupling, spatiotemporal prediction, spatiotemporal partitioning and summarization, spatiotemporal hotspots, and change detection. Compared with other surveys in the literature, this paper emphasizes the statistical foundations of spatiotemporal data mining and provides comprehensive coverage of computational approaches for various pattern families. ISPRS Int. J. Geo-Inf. 2015, 4 2307 We also list popular software tools for spatiotemporal data analysis. The survey concludes with a look at future research needs.

  11. Mines Systems Safety Improvement Using an Integrated Event Tree and Fault Tree Analysis

    Science.gov (United States)

    Kumar, Ranjan; Ghosh, Achyuta Krishna

    2017-04-01

    Mines systems such as ventilation system, strata support system, flame proof safety equipment, are exposed to dynamic operational conditions such as stress, humidity, dust, temperature, etc., and safety improvement of such systems can be done preferably during planning and design stage. However, the existing safety analysis methods do not handle the accident initiation and progression of mine systems explicitly. To bridge this gap, this paper presents an integrated Event Tree (ET) and Fault Tree (FT) approach for safety analysis and improvement of mine systems design. This approach includes ET and FT modeling coupled with redundancy allocation technique. In this method, a concept of top hazard probability is introduced for identifying system failure probability and redundancy is allocated to the system either at component or system level. A case study on mine methane explosion safety with two initiating events is performed. The results demonstrate that the presented method can reveal the accident scenarios and improve the safety of complex mine systems simultaneously.

  12. Localisation of an Unknown Number of Land Mines Using a Network of Vapour Detectors

    Directory of Open Access Journals (Sweden)

    Hiba Haj Chhadé

    2014-11-01

    Full Text Available We consider the problem of localising an unknown number of land mines usingconcentration information provided by a wireless sensor network. A number of vapoursensors/detectors, deployed in the region of interest, are able to detect the concentrationof the explosive vapours, emanating from buried land mines. The collected data iscommunicated to a fusion centre. Using a model for the transport of the explosive chemicalsin the air, we determine the unknown number of sources using a Principal ComponentAnalysis (PCA-based technique. We also formulate the inverse problem of determiningthe positions and emission rates of the land mines using concentration measurementsprovided by the wireless sensor network. We present a solution for this problem basedon a probabilistic Bayesian technique using a Markov chain Monte Carlo sampling scheme,and we compare it to the least squares optimisation approach. Experiments conducted onsimulated data show the effectiveness of the proposed approach.

  13. Localisation of an unknown number of land mines using a network of vapour detectors.

    Science.gov (United States)

    Chhadé, Hiba Haj; Abdallah, Fahed; Mougharbel, Imad; Gning, Amadou; Julier, Simon; Mihaylova, Lyudmila

    2014-11-06

    We consider the problem of localising an unknown number of land mines using concentration information provided by a wireless sensor network. A number of vapour sensors/detectors, deployed in the region of interest, are able to detect the concentration of the explosive vapours, emanating from buried land mines. The collected data is communicated to a fusion centre. Using a model for the transport of the explosive chemicals in the air, we determine the unknown number of sources using a Principal Component Analysis (PCA)-based technique. We also formulate the inverse problem of determining the positions and emission rates of the land mines using concentration measurements provided by the wireless sensor network. We present a solution for this problem based on a probabilistic Bayesian technique using a Markov chain Monte Carlo sampling scheme, and we compare it to the least squares optimisation approach. Experiments conducted on simulated data show the effectiveness of the proposed approach.

  14. Geotechnical Aspects of Explosive Compaction

    Directory of Open Access Journals (Sweden)

    Mahdi Shakeran

    2016-01-01

    Full Text Available Explosive Compaction (EC is the ground modification technique whereby the energy released from setting off explosives in subsoil inducing artificial earthquake effects, which compact the soil layers. The efficiency of EC predominantly depends on the soil profile, grain size distribution, initial status, and the intensity of energy applied to the soil. In this paper, in order to investigate the geotechnical aspects, which play an important role in performance of EC, a database has been compiled from thirteen-field tests or construction sites around the world, where EC has been successfully applied for modifying soil. This research focuses on evaluation of grain size distribution and initial stability status of deposits besides changes of soil penetration resistance due to EC. Results indicated suitable EC performance for unstable and liquefiable deposits having particle sizes ranging from gravel to silty sand with less than 40% silt content and less than 10% clay content. However, EC is most effective in fine-to-medium sands with a fine content less than 5% and hydraulically deposited with initial relative density ranging from 30% to 60%. Moreover, it has been observed that EC can be an effective method to improve the density, stability, and resistance of the target soils.

  15. Coal mine site reclamation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-02-15

    Coal mine sites can have significant effects on local environments. In addition to the physical disruption of land forms and ecosystems, mining can also leave behind a legacy of secondary detrimental effects due to leaching of acid and trace elements from discarded materials. This report looks at the remediation of both deep mine and opencast mine sites, covering reclamation methods, back-filling issues, drainage and restoration. Examples of national variations in the applicable legislation and in the definition of rehabilitation are compared. Ultimately, mine site rehabilitation should return sites to conditions where land forms, soils, hydrology, and flora and fauna are self-sustaining and compatible with surrounding land uses. Case studies are given to show what can be achieved and how some landscapes can actually be improved as a result of mining activity.

  16. Implementation of Paste Backfill Mining Technology in Chinese Coal Mines

    Directory of Open Access Journals (Sweden)

    Qingliang Chang

    2014-01-01

    Full Text Available Implementation of clean mining technology at coal mines is crucial to protect the environment and maintain balance among energy resources, consumption, and ecology. After reviewing present coal clean mining technology, we introduce the technology principles and technological process of paste backfill mining in coal mines and discuss the components and features of backfill materials, the constitution of the backfill system, and the backfill process. Specific implementation of this technology and its application are analyzed for paste backfill mining in Daizhuang Coal Mine; a practical implementation shows that paste backfill mining can improve the safety and excavation rate of coal mining, which can effectively resolve surface subsidence problems caused by underground mining activities, by utilizing solid waste such as coal gangues as a resource. Therefore, paste backfill mining is an effective clean coal mining technology, which has widespread application.

  17. Implementation of paste backfill mining technology in Chinese coal mines.

    Science.gov (United States)

    Chang, Qingliang; Chen, Jianhang; Zhou, Huaqiang; Bai, Jianbiao

    2014-01-01

    Implementation of clean mining technology at coal mines is crucial to protect the environment and maintain balance among energy resources, consumption, and ecology. After reviewing present coal clean mining technology, we introduce the technology principles and technological process of paste backfill mining in coal mines and discuss the components and features of backfill materials, the constitution of the backfill system, and the backfill process. Specific implementation of this technology and its application are analyzed for paste backfill mining in Daizhuang Coal Mine; a practical implementation shows that paste backfill mining can improve the safety and excavation rate of coal mining, which can effectively resolve surface subsidence problems caused by underground mining activities, by utilizing solid waste such as coal gangues as a resource. Therefore, paste backfill mining is an effective clean coal mining technology, which has widespread application.

  18. Light Stable Isotopes in Aquifers Affected by Mining Activities in a Brazilian Mining Province

    Science.gov (United States)

    Moreira, R. M.; de Carvalho, J. B.

    2013-05-01

    Iron ore is presently a main item in the Brazilian commercial agenda. Large reserves have converted this utility into an important source of export earnings and, secondarily, of raw materials for the domestic industry. Parallel to a boom in mining activities in the last years environmental impacts and a stress on natural resources have soared. A region exhibiting pronouncedly intensive mining activities lies in the central part of the State of Minas Gerais, the third economy of the federation. Mines are sited right beside the capital and neighbor towns amounting to nearly five million inhabitants and a pronounced dependence on groundwater resources. Besides, this region is a water divide enclosing the sources of main contributors to the most strategic fluvial basins in the country. Iron ore is by large the main mineral but other metals (including gold and uranium), as well as non-metals such as limestone, quartz and granite, also occur. Given the significance of this commodity in the country's trade balance and the demand of water resources with acceptable quality for human consumption, the scale of ensuing water use conflicts caused by its exploration is wide ranging and has to be coped with well grounded environmental assessment approaches. Tracer hydrology techniques might be a valuable tool in this context. The characteristics of the area being impacted have been surveyed, including climate and pluviometry, stratigraphic litology, geological structure, use of soil, mineral resources and their exploration, surface and ground water hydrology and their sundry uses. Data to be processed have been procured at local public agencies but as regard local hydrological features, particularly isotopic compositions, ad hoc surveys and methodologies were required. One instance concerns pluviometric isotopy due to the alpine character of the surveyed region altitude and temperature effects might take place. Hence different sites were monitored; cumulative pluviometer samples

  19. Synergy of metal and nonmetal dopants for visible-light photocatalysis: a case-study of Sn and N co-doped TiO2.

    Science.gov (United States)

    Zhuang, Huaqiang; Zhang, Yingguang; Chu, Zhenwei; Long, Jinlin; An, Xiaohan; Zhang, Hongwen; Lin, Huaxiang; Zhang, Zizhong; Wang, Xuxu

    2016-04-14

    This paper mainly focuses on the synergistic effect of Sn and N dopants to enhance the photocatalytic performance of anatase TiO2 under visible light or simulated solar light irradiation. The Sn and N co-doped TiO2 (SNT-x) photocatalysts were successfully prepared by the facile sol-gel method and the post-nitridation route in the temperature range of 400-550 °C. All the as-prepared samples were characterized in detail by X-ray diffraction, UV-vis diffuse reflectance spectroscopy, transmission electron microscopy, X-ray photoelectron and electron spin resonance spectroscopy and photoelectrochemical measurements. The characterization results reveal that the co-incorporation of Sn and N atoms remarkably modifies the electronic structure of TiO2, which gives rise to a prominent separation of photogenerated charge carriers and more efficient interfacial charge-transfer reactions in a photocatalytic process. The enhanced photocatalytic activity is attributed to the intensified active oxygen species including hydroxyl radicals (˙OH) and superoxide anion radicals (O2˙(-)) for degradation of organic pollutants. And the result of photocatalytic hydrogen production further confirms the existence of the synergistic effect in the SNT-x samples, because they exhibit higher photocatalytic activity than the sum of N/TiO2 and Sn/TiO2. This work provides a paradigm to consolidate the understanding of the synergistic effect of metal and non-metal co-doped TiO2 in domains of photocatalysis and photoelectrochemistry.

  20. A REVIEW ON TEXT MINING IN DATA MINING

    OpenAIRE

    2016-01-01

    Data mining is the knowledge discovery in databases and the gaol is to extract patterns and knowledge from large amounts of data. The important term in data mining is text mining. Text mining extracts the quality information highly from text. Statistical pattern learning is used to high quality information. High –quality in text mining defines the combinations of relevance, novelty and interestingness. Tasks in text mining are text categorization, text clustering, entity extraction and sentim...

  1. Explosions inside Ejecta and Most Luminous Supernovae

    CERN Document Server

    Blinnikov, S I

    2008-01-01

    The extremely luminous supernova SN2006gy is explained in the same way as other SNIIn events: light is produced by a radiative shock propagating in a dense circumstellar envelope formed by a previous weak explosion. The problems in the theory and observations of multiple-explosion SNe IIn are briefly reviewed.

  2. Simulation of explosive welding with ANFO mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Mousavi, A.A. Akbari; Burley, Stephen J.; Al-Hassani, S.T.S. [Department of Mechanical, Aerospace and Manufacturing Engineering, UMIST, PO Box 88, Manchester M60 1QD (United Kingdom); Byers Brown, W. [Mass Action Research Consultancy, Devonshire House, 14 Corbar Road, Buxton, SK17 6RQ (United Kingdom)

    2004-06-01

    The work described here arose from a study into explosive welding. As part of that study, the impact velocity of stainless steel and titanium plates to grazing detonation of ANFO/perlite, the velocity of detonation were measured. Computer simulation required a new model which copes with an equation of state of low explosives. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

  3. 77 FR 55108 - Explosive Siting Requirements

    Science.gov (United States)

    2012-09-07

    ... trinitrotoluene (TNT) equivalents of less than or equal to 450 pounds. Although decreased, the revised separation... required separation distances for division 1.1 explosives and liquid propellants with TNT equivalents that... separation from a given net explosive weight (NEW) is one percent, which is an equivalent level of safety...

  4. Some analytical methods for explosives: Part 2

    Energy Technology Data Exchange (ETDEWEB)

    Selig, W.

    1965-12-08

    This report is the second compilation of methods for analyzing explosives. All the methods were developed for routine performance by techniques, and an attempt has therefore been made to keep them as simple as possible. Methods are presented for analyzing plastic-bonded explosives based on sym-cyclomethylenetetra-nitramine (HMX), based on viton in addition to HMX, and based on pentraerythritol tetranitrate (PETN).

  5. Sensitivity to friction for primary explosives

    Energy Technology Data Exchange (ETDEWEB)

    Matyas, Robert, E-mail: robert.matyas@upce.cz [Institute of Energetic Materials, Faculty of Chemical Technology, University of Pardubice, Pardubice 532 10 (Czech Republic); Selesovsky, Jakub; Musil, Tomas [Institute of Energetic Materials, Faculty of Chemical Technology, University of Pardubice, Pardubice 532 10 (Czech Republic)

    2012-04-30

    Highlights: Black-Right-Pointing-Pointer The friction sensitivity of 14 samples of primary explosives was determined. Black-Right-Pointing-Pointer The same apparatus (small scale BAM) and the same method (probit analysis) was used. Black-Right-Pointing-Pointer The crystal shapes and sizes were documented with microscopy. Black-Right-Pointing-Pointer Almost all samples are less sensitive than lead azide, which is commercially used. Black-Right-Pointing-Pointer The organic peroxides (TATP, DADP, HMTD) are not as sensitive as often reported. - Abstract: The sensitivity to friction for a selection of primary explosives has been studied using a small BAM friction apparatus. The probit analysis was used for the construction of a sensitivity curve for each primary explosive tested. Two groups of primary explosives were chosen for measurement (a) the most commonly used industrially produced primary explosives (e.g. lead azide, tetrazene, dinol, lead styphnate) and (b) the most produced improvised primary explosives (e.g. triacetone triperoxide, hexamethylenetriperoxide diamine, mercury fulminate, acetylides of heavy metals). A knowledge of friction sensitivity is very important for determining manipulation safety for primary explosives. All the primary explosives tested were carefully characterised (synthesis procedure, shape and size of crystals). The sensitivity curves obtained represent a unique set of data, which cannot be found anywhere else in the available literature.

  6. Gas explosion prediction using CFD models

    Energy Technology Data Exchange (ETDEWEB)

    Niemann-Delius, C.; Okafor, E. [RWTH Aachen Univ. (Germany); Buhrow, C. [TU Bergakademie Freiberg Univ. (Germany)

    2006-07-15

    A number of CFD models are currently available to model gaseous explosions in complex geometries. Some of these tools allow the representation of complex environments within hydrocarbon production plants. In certain explosion scenarios, a correction is usually made for the presence of buildings and other complexities by using crude approximations to obtain realistic estimates of explosion behaviour as can be found when predicting the strength of blast waves resulting from initial explosions. With the advance of computational technology, and greater availability of computing power, computational fluid dynamics (CFD) tools are becoming increasingly available for solving such a wide range of explosion problems. A CFD-based explosion code - FLACS can, for instance, be confidently used to understand the impact of blast overpressures in a plant environment consisting of obstacles such as buildings, structures, and pipes. With its porosity concept representing geometry details smaller than the grid, FLACS can represent geometry well, even when using coarse grid resolutions. The performance of FLACS has been evaluated using a wide range of field data. In the present paper, the concept of computational fluid dynamics (CFD) and its application to gas explosion prediction is presented. Furthermore, the predictive capabilities of CFD-based gaseous explosion simulators are demonstrated using FLACS. Details about the FLACS-code, some extensions made to FLACS, model validation exercises, application, and some results from blast load prediction within an industrial facility are presented. (orig.)

  7. Summary of European directives for explosion safety

    NARCIS (Netherlands)

    Versloot, N.H.A.; Klein, A.J.J.; Maaijer, M. de

    2008-01-01

    On July 1, 2003 a transitional period has ended and two European directives became fully active: • Directive 1999/92/EC • Directive 94/9/EC These directives have an impact on companies with an explosion hazard (gas, vapor, mist, or dust explosions) and on manufacturers of equipment intended to be

  8. Explosion risks and consequences for tunnels

    NARCIS (Netherlands)

    Weerheijm, J.; Berg, A.C. van den

    2014-01-01

    Tunnel accidents with transports of dangerous goods may lead to explosions. Risk assessment for these accidents is complicated because of the low probability and the unknown, but disastrous effects expected. Especially the lack of knowledge on the strength of the explosion and the consequences for t

  9. Numerical simulation of disaster effects induced by typical industrial explosive explosion%典型工业炸药爆炸灾害效应的数值模拟

    Institute of Scientific and Technical Information of China (English)

    段云; 熊代余; 李国仲; 张鑫

    2011-01-01

    为了评价典型工业炸药在空气中发生意外爆炸产生的灾害效应,利用非线性动力学软件AUTODYN,炸药产物选用JWL状态方程,分析1 kg铵油炸药、乳化炸药、2号岩石炸药在空气自由场中爆炸冲击波的传播特性和温度场分布情况,并与TNT炸药进行对比分析.计算结果表明,冲击波损害效应中,2号岩石炸药与TNT炸药爆炸产生的冲击波峰值相当,乳化炸药次之;温度灾害效应中,岩石炸药的温度峰值最高,铵油炸药温度峰值次之,乳化炸药温度峰值最低.为正确使用工业炸药和矿山安全提供了理论依据.%In order to evaluate the disaster effects generated by accidental explosion in air for typical industrial explosives,the spreading characteristics of air shock waves and temperature field of free-field explosion for 1kg ANFO,emulsion explosives and the 2nd rock explosives are investigated based on the nonlinear dynamics software AUTODYN and JWL state equation of explosion products,and are compared with TNT explosives.The calculated results show that in the temperature damage effect,the highest temperature is generated by rock explosives;the second is ANFO,followed by emulsion explosives.That disaster effect of temperature,the highest temperature is generated by the 2nd rock explosives and the second is ANFO,followed by the lowest temperature peak emulsion explosive.These conclusions provide theoretical basis for the correct use of industrial explosives and the safety of mines.

  10. Hydrodynamics of Explosion Experiments and Models

    CERN Document Server

    Kedrinskii, Valery K

    2005-01-01

    Hydronamics of Explosion presents the research results for the problems of underwater explosions and contains a detailed analysis of the structure and the parameters of the wave fields generated by explosions of cord and spiral charges, a description of the formation mechanisms for a wide range of cumulative flows at underwater explosions near the free surface, and the relevant mathematical models. Shock-wave transformation in bubbly liquids, shock-wave amplification due to collision and focusing, and the formation of bubble detonation waves in reactive bubbly liquids are studied in detail. Particular emphasis is placed on the investigation of wave processes in cavitating liquids, which incorporates the concepts of the strength of real liquids containing natural microinhomogeneities, the relaxation of tensile stress, and the cavitation fracture of a liquid as the inversion of its two-phase state under impulsive (explosive) loading. The problems are classed among essentially nonlinear processes that occur unde...

  11. Morphomechanical Innovation Drives Explosive Seed Dispersal.

    Science.gov (United States)

    Hofhuis, Hugo; Moulton, Derek; Lessinnes, Thomas; Routier-Kierzkowska, Anne-Lise; Bomphrey, Richard J; Mosca, Gabriella; Reinhardt, Hagen; Sarchet, Penny; Gan, Xiangchao; Tsiantis, Miltos; Ventikos, Yiannis; Walker, Simon; Goriely, Alain; Smith, Richard; Hay, Angela

    2016-06-30

    How mechanical and biological processes are coordinated across cells, tissues, and organs to produce complex traits is a key question in biology. Cardamine hirsuta, a relative of Arabidopsis thaliana, uses an explosive mechanism to disperse its seeds. We show that this trait evolved through morphomechanical innovations at different spatial scales. At the organ scale, tension within the fruit wall generates the elastic energy required for explosion. This tension is produced by differential contraction of fruit wall tissues through an active mechanism involving turgor pressure, cell geometry, and wall properties of the epidermis. Explosive release of this tension is controlled at the cellular scale by asymmetric lignin deposition within endocarp b cells-a striking pattern that is strictly associated with explosive pod shatter across the Brassicaceae plant family. By bridging these different scales, we present an integrated mechanism for explosive seed dispersal that links evolutionary novelty with complex trait innovation. VIDEO ABSTRACT.

  12. [Explosion injuries - prehospital care and management].

    Science.gov (United States)

    Holsträter, Thorsten; Holsträter, Susanne; Rein, Daniela; Helm, Matthias; Hossfeld, Björn

    2013-11-01

    Explosion injuries are not restricted to war-like military conflicts or terrorist attacks. The emergency physician may also encounter such injuries in the private or industrial fields, injuries caused by fireworks or gas explosions. In such cases the injury patterns are especially complex and may consist of blunt and penetrating injuries as well as thermal damage. Emergency medical personnel must be prepared to cope with explosion trauma not only in individual cases but also in major casualty incidents (MCI). This necessitates a sound knowledge about the mechanisms and processes of an explosion as well as the particular pathophysiological relationships of explosion injuries in order to be able to initiate the best possible, guideline-conform trauma therapy.

  13. Regional gas drainage techniques in Chinese coal mines

    Institute of Scientific and Technical Information of China (English)

    Wang Haifeng; Cheng Yuanping; Wang Lei

    2012-01-01

    China's rapid economic development has increased the demand for coal.These results in Chinese coal mines being extended to deeper levels.The eastern Chinese,more economical developed,regions have a long history of coal mining and many coal mines have now started deep mining at a depth from 800 to 1500 m.This increase in mining depth,geostresses,pressures,and gas content of the coal seam complicates geologic construction conditions.Lower permeability and softer coal contribute to increasing numbers of coal and gas outburst,and gas explosion,disasters.A search on effective methods of preventing gas disasters has been provided funds from the Chinese government since 1998.The National Engineering Research Center of Coal Gas Control and the Huainan and Huaibei Mining Group have conducted theoretical and experimental research on a regional gas extraction technology.The results included two important findings.First,grouped coal seams allow adoption of a method where a first,key protective layer is mined to protect upper and lower coal seams by increasing permeability from 400 to 3000 times.Desorption of gas and gas extraction in the protected coal seam of up to 60%,or more,may be achieved in this way.Second,a single seam may be protected by using a dense network of extraction boreholes consisting of cross and along-bed holes.Combined with this is increased use of water that increases extraction of coal seam gas by up to 50%.Engineering practice showed that regional gas drainage technology eliminates regional coal and gas outburst and also enables mining under low gas conditions.These research results have been adopted into the national safety codes of production technology.This paper systematically introduces the principles of the technology,the engineering methods and techniques,and the parameters of regional gas drainage.Engineering applications are discussed.

  14. Regional gas drainage techniques in Chinese coal mines

    Institute of Scientific and Technical Information of China (English)

    Wang; Haifeng; Cheng; Yuanping; Wang; Lei

    2012-01-01

    China's rapid economic development has increased the demand for coal.These results in Chinese coal mines being extended to deeper levels.The eastern Chinese,more economical developed,regions have a long history of coal mining and many coal mines have now started deep mining at a depth from 800 to 1500 m.This increase in mining depth,geostresses,pressures,and gas content of the coal seam complicates geologic construction conditions.Lower permeability and softer coal contribute to increasing numbers of coal and gas outburst,and gas explosion,disasters.A search on effective methods of preventing gas disasters has been provided funds from the Chinese government since 1998.The National Engineering Research Center of Coal Gas Control and the Huainan and Huaibei Mining Group have conducted theoretical and experimental research on a regional gas extraction technology.The results included two important findings.First,grouped coal seams allow adoption of a method where a first,key protective layer is mined to protect upper and lower coal seams by increasing permeability from 400 to 3000 times.Desorption of gas and gas extraction in the protected coal seam of up to 60%,or more,may be achieved in this way.Second,a single seam may be protected by using a dense network of extraction boreholes consisting of cross and along-bed holes.Combined with this is increased use of water that increases extraction of coal seam gas by up to 50%.Engineering practice showed that regional gas drainage technology eliminates regional coal and gas outburst and also enables mining under low gas conditions.These research results have been adopted into the national safety codes of production technology.This paper systematically introduces the principles of the technology,the engineering methods and techniques,and the parameters of regional gas drainage.Engineering applications are discussed.

  15. Explosion probability of unexploded ordnance: expert beliefs.

    Science.gov (United States)

    MacDonald, Jacqueline Anne; Small, Mitchell J; Morgan, M G

    2008-08-01

    This article reports on a study to quantify expert beliefs about the explosion probability of unexploded ordnance (UXO). Some 1,976 sites at closed military bases in the United States are contaminated with UXO and are slated for cleanup, at an estimated cost of $15-140 billion. Because no available technology can guarantee 100% removal of UXO, information about explosion probability is needed to assess the residual risks of civilian reuse of closed military bases and to make decisions about how much to invest in cleanup. This study elicited probability distributions for the chance of UXO explosion from 25 experts in explosive ordnance disposal, all of whom have had field experience in UXO identification and deactivation. The study considered six different scenarios: three different types of UXO handled in two different ways (one involving children and the other involving construction workers). We also asked the experts to rank by sensitivity to explosion 20 different kinds of UXO found at a case study site at Fort Ord, California. We found that the experts do not agree about the probability of UXO explosion, with significant differences among experts in their mean estimates of explosion probabilities and in the amount of uncertainty that they express in their estimates. In three of the six scenarios, the divergence was so great that the average of all the expert probability distributions was statistically indistinguishable from a uniform (0, 1) distribution-suggesting that the sum of expert opinion provides no information at all about the explosion risk. The experts' opinions on the relative sensitivity to explosion of the 20 UXO items also diverged. The average correlation between rankings of any pair of experts was 0.41, which, statistically, is barely significant (p= 0.049) at the 95% confidence level. Thus, one expert's rankings provide little predictive information about another's rankings. The lack of consensus among experts suggests that empirical studies

  16. Chemical analysis kit for the presence of explosives

    Science.gov (United States)

    Eckels, Joel Del [Livermore, CA; Nunes,; Peter, J [Danville, CA; Alcaraz, Armando [Livermore, CA; Whipple, Richard E [Livermore, CA

    2011-05-10

    A tester for testing for explosives associated with a test location comprising a first explosives detecting reagent; a first reagent holder, the first reagent holder containing the first explosives detecting reagent; a second explosives detecting reagent; a second reagent holder, the second reagent holder containing the second explosives detecting reagent; a sample collection unit for exposure to the test location, exposure to the first explosives detecting reagent, and exposure to the second explosives detecting reagent; and a body unit containing a heater for heating the sample collection unit for testing the test location for the explosives.

  17. Noise and dust emissions from mining activities : a software for a first approach to the measurement management and selection of suitable reduction techniques

    Energy Technology Data Exchange (ETDEWEB)

    Cigna, C.; Lovera, E.; Patrucco, M. [Politecnico di Torino, Turin (Italy)

    2005-07-01

    Mining activities are often a matter of concern to local communities due to the potential impacts on the environment and landscape. As such, an effective balance is needed between socio-economic development and environmental protection. Mining activities in populated areas must be carefully planned and managed in order to avoid annoying local populations and to minimize health risks. This study was based on the criteria of the European Communities Commission to promote resource extraction and production methods that encourage eco-efficiency by developing best practice programs. In particular, this study defined and evaluated measurement, analysis and control criteria for the emission of chemical and physical pollutants from non-metal mining industries with particular reference to the reduction of noise and airborne particulates to the surrounding environment. The main focus of the study included on-site measuring campaigns in Italy's Lombardia mining region to collect data on mining techniques and technologies as well as pollutant emissions and propagation. The objective was to test the applicability of a newly proposed simplified monitoring systems and to evaluate the effective results of adopted pollution reduction strategies. A software-based database was also developed to manage detailed information on mining activities and to store the measured emissions data for future evaluation. 3 refs., 7 figs.

  18. 30 CFR 57.6407 - Circuit testing.

    Science.gov (United States)

    2010-07-01

    ... SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Explosives Electric Blasting-Surface and Underground § 57.6407 Circuit testing. A blasting galvanometer or other instrument designed for testing blasting circuits shall be used to test the following: (a) In surface operations—...

  19. 30 CFR 57.6404 - Separation of blasting circuits from power source.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Separation of blasting circuits from power... NONMETAL MINES Explosives Electric Blasting-Surface and Underground § 57.6404 Separation of blasting circuits from power source. (a) Switches used to connect the power source to a blasting circuit shall...

  20. Rock blasting and explosives engineering

    Energy Technology Data Exchange (ETDEWEB)

    Persson, P.-A.; Holmberg, R.; Lee, J. (New Mexico Institute of Mining and Technology, Socorro, NM (United States). Research Center for Energetic Materials)

    1994-01-01

    The book covers the practical engineering aspects of different kinds of rock blasting. It includes a thorough analysis of the cost of the entire process of tunneling by drilling and blasting compared with full-face boring. It covers the economics of the entire rock blasting operation and its dependence on the size of excavation. The book highlights the fundamentals of rock mechanics, shock waves and detonation, initiation and mechanics of rock motion. It describes the engineering design principles and computational techniques for many separate mining methods and rock blasting operations. 274 refs.